Science.gov

Sample records for laser ablation processes

  1. Dynamical modeling of laser ablation processes

    SciTech Connect

    Leboeuf, J.N.; Chen, K.R.; Donato, J.M.; Geohegan, D.B.; Liu, C.L.; Puretzky, A.A.; Wood, R.F.

    1995-09-01

    Several physics and computational approaches have been developed to globally characterize phenomena important for film growth by pulsed laser deposition of materials. These include thermal models of laser-solid target interactions that initiate the vapor plume; plume ionization and heating through laser absorption beyond local thermodynamic equilibrium mechanisms; gas dynamic, hydrodynamic, and collisional descriptions of plume transport; and molecular dynamics models of the interaction of plume particles with the deposition substrate. The complexity of the phenomena involved in the laser ablation process is matched by the diversity of the modeling task, which combines materials science, atomic physics, and plasma physics.

  2. Physical processes of laser tissue ablation

    NASA Astrophysics Data System (ADS)

    Furzikov, Nickolay P.

    1991-05-01

    The revised ablation model applicable to homogeneous tissues is presented. It is based on the thermal mechanism and involves the instability of the laserinduced evaporation (thermodestruction) front the growth of the surface ripple structure the interference of the laser wave and of the surface wave arising by diffraction on the ripples Beer''s law violation the pulsed thermodestruction of the organic structural component the tissue water boiling and gas dynamic expansion of the resulting products into the surrounding medium which is followed by the shock wave formation. The UV and IR ablation schemes were implemented and compared to the corneal ablation experiments. The initial ablation pressure and temperature are given restored from the timeofflight measurements of the supersonic expansion of the product. 1.

  3. Experimental investigation of the laser ablation process on wood surfaces

    NASA Astrophysics Data System (ADS)

    Panzner, M.; Wiedemann, G.; Henneberg, K.; Fischer, R.; Wittke, Th.; Dietsch, R.

    1998-05-01

    Processing of wood by conventional mechanical tools like saws or planes leaves behind a layer of squeezed wood only slightly adhering to the solid wood surface. Laser ablation of this layer could improve the durability of coatings and glued joints. For technical applications, thorough knowledge about the laser ablation process is necessary. Results of ablation experiments by excimer lasers, Nd:YAG lasers, and TEA-CO 2 lasers on surfaces of different wood types and cut orientations are shown. The process of ablation was observed by a high-speed camera system and optical spectroscopy. The influence of the experimental parameters are demonstrated by SEM images and measurement of the ablation rate depending on energy density. Thermal effects like melting and also carbonizing of cellulose were found for IR- and also UV-laser wavelengths. Damage of the wood surface after laser ablation was weaker for excimer lasers and CO 2-TEA lasers. This can be explained by the high absorption of wood in the ultraviolet and middle infrared spectral range. As an additional result, this technique provides an easy way for preparing wood surfaces with excellently conserved cellular structure.

  4. Revisiting the interplay between ablation, collisional, and radiative processes during ns-laser ablation

    NASA Astrophysics Data System (ADS)

    Autrique, D.; Gornushkin, I.; Alexiades, V.; Chen, Z.; Bogaerts, A.; Rethfeld, B.

    2013-10-01

    A study of ns-laser ablation is presented, which focuses on the transient behavior of the physical processes that act in and above a copper sample. A dimensionless multiphase collisional radiative model describes the interplay between the ablation, collisional, and radiative mechanisms. Calculations are done for a 6 ns-Nd:YAG laser pulse operating at 532 nm and fluences up to 15 J/cm2. Temporal intensity profiles as well as transmissivities are in good agreement with experimental results. It is found that volumetric ablation mechanisms and photo-processes both play an essential role in the onset of ns-laser induced breakdown.

  5. Mechanisms of Carbon Nanotube Production by Laser Ablation Process

    NASA Technical Reports Server (NTRS)

    Scott, Carl D.; Arepalli, Sivaram; Nikolaev, Pavel; Smalley, Richard E.; Nocholson, Leonard S. (Technical Monitor)

    2000-01-01

    We will present possible mechanisms for nanotube production by laser oven process. Spectral emission of excited species during laser ablation of a composite graphite target is compared with that of laser irradiated C60 vapor. The similarities in the transient and spectral data suggest that fullerenes are intermediate precursors for nanotube formation. The confinement of the ablation products by means of a 25-mm diameter tube placed upstream of the target seems to improve the production and purity of nanotubes. Repeated laser pulses vaporize the amorphous/graphitic carbon and possibly catalyst particles, and dissociate fullerenes yielding additional feedstock for SWNT growth.

  6. Modeling of dynamical processes in laser ablation

    SciTech Connect

    Leboeuf, J.N.; Chen, K.R.; Donato, J.M.; Geohegan, D.B.; Liu, C.L.; Puretzky, A.A.; Wood, R.F.

    1995-12-31

    Various physics and computational approaches have been developed to globally characterize phenomena important for film growth by pulsed-laser deposition of materials. These include thermal models of laser-solid target interactions that initiate the vapor plume, plume ionization and heating through laser absorption beyond local thermodynamic equilibrium mechanisms, hydrodynamic and collisional descriptions of plume transport, and molecular dynamics models of the interaction of plume particles with the deposition substrate.

  7. Laser backwriting process on glass via ablation of metal targets

    NASA Astrophysics Data System (ADS)

    Castelo, A.; Nieto, D.; Bao, C.; Flores-Arias, M. T.; Pérez, M. V.; Gómez-Reino, C.; López-Gascón, C.; de la Fuente, G. F.

    2007-05-01

    Ablation of metal targets onto pyrex glass substrates, using a Q-switched Nd:YAG laser working at 355 nm, was used to study the potential of a laser backwriting process for the fabrication of optical waveguides via an index of refraction change. Metal foils of stainless steel, aluminum, copper, brass and gold have been used as blanks and irradiated by focusing the laser beam through a cylindrical lens under continuous movement in a direction perpendicular to the irradiation. An horizontal setup was found suitable to improve the effect of the plume in the sample. Results were obtained for two different configurations. Transversal profiles were analysed using a contact profilometer, comparing results obtained for the different configurations, traverse speeds and metal targets used. Two ablation regimes were identified, which are related to a critical laser fluence value of 2.7 J/cm 2. Surface micrographs obtained by scanning electron microscopy are discussed, together with the characteristics of the structures attained, taking into account the optical and thermal properties of the ablated metal blanks.

  8. Ablation by ultrashort laser pulses: Atomistic and thermodynamic analysis of the processes at the ablation threshold

    SciTech Connect

    Upadhyay, Arun K.; Inogamov, Nail A.; Rethfeld, Baerbel; Urbassek, Herbert M.

    2008-07-15

    Ultrafast laser irradiation of solids may ablate material off the surface. We study this process for thin films using molecular-dynamics simulation and thermodynamic analysis. Both metals and Lennard-Jones (LJ) materials are studied. We find that despite the large difference in thermodynamical properties between these two classes of materials--e.g., for aluminum versus LJ the ratio T{sub c}/T{sub tr} of critical to triple-point temperature differs by more than a factor of 4--the values of the ablation threshold energy E{sub abl} normalized to the cohesion energy, {epsilon}{sub abl}=E{sub abl}/E{sub coh}, are surprisingly universal: all are near 0.3 with {+-}30% scattering. The difference in the ratio T{sub c}/T{sub tr} means that for metals the melting threshold {epsilon}{sub m} is low, {epsilon}{sub m}<{epsilon}{sub abl}, while for LJ it is high, {epsilon}{sub m}>{epsilon}{sub abl}. This thermodynamical consideration gives a simple explanation for the difference between metals and LJ. It explains why despite the universality in {epsilon}{sub abl}, metals thermomechanically ablate always from the liquid state. This is opposite to LJ materials, which (near threshold) ablate from the solid state. Furthermore, we find that immediately below the ablation threshold, the formation of large voids (cavitation) in the irradiated material leads to a strong temporary expansion on a very slow time scale. This feature is easily distinguished from the acoustic oscillations governing the material response at smaller intensities, on the one hand, and the ablation occurring at larger intensities, on the other hand. This finding allows us to explain the puzzle of huge surface excursions found in experiments at near-threshold laser irradiation.

  9. Cultured human cornea healing process after free-electron-laser ablation

    NASA Astrophysics Data System (ADS)

    Shen, Jin-Hui; Joos, Karen M.; Shetlar, Debra J.; Robinson, Richard D.; Thind, Gurpreet K.; Edwards, Glenn S.; O'Day, Denis M.

    1997-05-01

    The purpose of this study is to investigate the healing process in cultured human cornea after infrared Free Electron Laser ablation. Fresh human cadaver cornea was ablated using the Free Electron Laser at the amide II band peak (6.45 micrometers ). The cornea was then cultured in an incubator for 18 days. Haze development within the ablated area was monitored during culture. Histologic sections of the cornea showed complete re-epithelialization of the lased area, and ablation of the underlying Bowman's layer and stroma. The endothelium appeared unaffected. Cultured human corneas may provide useful information regarding the healing process following laser ablation.

  10. Process and structures for fabrication of solar cells with laser ablation steps to form contact holes

    DOEpatents

    Harley, Gabriel; Smith, David D; Dennis, Tim; Waldhauer, Ann; Kim, Taeseok; Cousins, Peter John

    2013-11-19

    Contact holes of solar cells are formed by laser ablation to accomodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thickness.

  11. Deposition of superconducting thin films by laser ablation processing

    SciTech Connect

    Kim, B.F.; Bohandy, J.; Moorjani, K.; Adrian, F.J.

    1988-02-25

    Superconducting thin films, approximately 1 ..mu..m thick and 1 cm/sup 2/ in area, have been deposited on fused silica by ablation of the bulk material, YBa/sub 2/Cu/sub 3/O/sub 7-y/, using a pulsed excimer laser. The presence of superconductivity in as-deposited films was established by a novel variation of the technique of microwave absorption, in which the superconducting transition appears as a peak in the temperature dependence of the microwave response. The method is sensitive enough to allow detection of superconductivity in small (approx.0.1 mg) samples and is capable of resolving multiple superconducting phases with slight differences in T/sub c/. As-deposited films have essentially the same value of T/sub c/ (94K) as the bulk material.

  12. Laser ablation process for single-walled carbon nanotube production

    NASA Technical Reports Server (NTRS)

    Arepalli, Sivaram

    2004-01-01

    Different types of lasers are now routinely used to prepare single-walled carbon nanotubes. The original method developed by researchers at Rice University used a "double-pulse laser oven" process. Several researchers have used variations of the lasers to include one-laser pulse (green or infrared), different pulse widths (ns to micros as well as continuous wave), and different laser wavelengths (e.g., CO2, or free electron lasers in the near to far infrared). Some of these variations are tried with different combinations and concentrations of metal catalysts, buffer gases (e.g., helium), oven temperatures, flow conditions, and even different porosities of the graphite targets. This article is an attempt to cover all these variations and their relative merits. Possible growth mechanisms under these different conditions will also be discussed.

  13. Parametric Study of Carbon Nanotube Production by Laser Ablation Process

    NASA Technical Reports Server (NTRS)

    Arepalli, Sivaram; Nikolaev, Pavel; Holmes, William; Hadjiev, Victor; Scott, Carl

    2002-01-01

    Carbon nanotubes form a new class of nanomaterials that are presumed to have extraordinary mechanical, electrical and thermal properties. The single wall nanotubes (SWNTs) are estimated to be 100 times stronger than steel with 1/6th the weight; electrical carrying capacity better than copper and thermal conductivity better than diamond. Applications of these SWNTs include possible weight reduction of aerospace structures, multifunctional materials, nanosensors and nanoelectronics. Double pulsed laser vaporization process produces SWNTs with the highest percentage of nanotubes in the output material. The normal operating conditions include a green laser pulse closely followed by an infrared laser pulse. Lasers ab late a metal-containing graphite target located in a flow tube maintained in an oven at 1473K with argon flow of 100 sccm at a 500 Torr pressure. In the present work a number of production runs were carried out, changing one operating condition at a time. We have studied the effects of nine parameters, including the sequencing of the laser pulses, pulse separation times, laser energy densities, the type of buffer gas used, oven temperature, operating pressure, flow rate and inner flow tube diameters. All runs were done using the same graphite target. The collected nanotube material was characterized by a variety of analytical techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman and thermo gravimetric analysis (TGA). Results indicate trends that could be used to optimize the process and increase the efficiency of the production process.

  14. Laser ablation plasmas for diagnostics of structured electronic and optical materials during or after laser processing

    NASA Astrophysics Data System (ADS)

    Russo, Richard E.; Bol'shakov, Alexander A.; Yoo, Jong H.; González, Jhanis J.

    2012-03-01

    Laser induced plasma can be used for rapid optical diagnostics of electronic, optical, electro-optical, electromechanical and other structures. Plasma monitoring and diagnostics can be realized during laser processing in real time by means of measuring optical emission that originates from the pulsed laser-material interaction. In post-process applications, e.g., quality assurance and quality control, surface raster scanning and depth profiling can be realized with high spatial resolution (~10 nm in depth and ~3 μm lateral). Commercial instruments based on laser induced breakdown spectrometry (LIBS) are available for these purposes. Since only a laser beam comes in direct contact with the sample, such diagnostics are sterile and non-disruptive, and can be performed at a distance, e.g. through a window. The technique enables rapid micro-localized chemical analysis without a need for sample preparation, dissolution or evacuation of samples, thus it is particularly beneficial in fabrication of thin films and structures, such as electronic, photovoltaic and electro-optical devices or circuits of devices. Spectrum acquisition from a single laser shot provides detection limits for metal traces of ~10 μg/g, which can be further improved by accumulating signal from multiple laser pulses. LIBS detection limit for Br in polyethylene is 90 μg/g using 50-shot spectral accumulation (halogen detection is a requirement for semiconductor package materials). Three to four orders of magnitude lower detection limits can be obtained with a femtosecond laser ablation - inductively coupled plasma mass spectrometer (LA-ICP-MS), which is also provided on commercial basis. Laser repetition rate is currently up to 20 Hz in LIBS instruments and up to 100 kHz in LA-ICP-MS.

  15. 3D transient model to predict temperature and ablated areas during laser processing of metallic surfaces

    NASA Astrophysics Data System (ADS)

    Naghshine, Babak. B.; Kiani, Amirkianoosh

    2017-02-01

    Laser processing is one of the most popular small-scale patterning methods and has many applications in semiconductor device fabrication and biomedical engineering. Numerical modelling of this process can be used for better understanding of the process, optimization, and predicting the quality of the final product. An accurate 3D model is presented here for short laser pulses that can predict the ablation depth and temperature distribution on any section of the material in a minimal amount of time. In this transient model, variations of thermal properties, plasma shielding, and phase change are considered. Ablation depth was measured using a 3D optical profiler. Calculated depths are in good agreement with measured values on laser treated titanium surfaces. The proposed model can be applied to a wide range of materials and laser systems.

  16. Modeling of the human enamel laser ablation process at the mesoscopic scale

    NASA Astrophysics Data System (ADS)

    Vila Verde, Ana C.; Duarte Ramos, Marta Maria; Mendes Ribeiro, Ricardo; Stoneham, Marshall

    2003-06-01

    A mesoscopic simulation of the process of human enamel laser ablation by Er:YAG and CO2 lasers is being developed using the finite element method, taking into account the complex structure and chemical composition of this material. A geometric model that allows studying in detail the temperature, stress and displacement distribution within a few enamel rods is presented. The heat generation that takes place inside the enamel at the centre of the laser spot, caused by a non-ablative laser pulse emitted by CO2 and Er:YAG lasers, was simulated. The sensitivity of our model to the estimated material parameters was studied. Temperature, displacement and stress distribution maps obtained for both lasers are presented. These preliminary results suggest that the temperature distribution across the enamel rods is different in the two situations considered; thermally induced stresses in the material are higher in the regions that are richer in hydroxyapatite (HA), and the higher displacements are observed in the regions that are rich in water. The rod tails inside enamel present higher stresses in the direction perpendicular to the surface of enamel than the ones that are created at the surface of our simulated structure. We conclude that the mesostructure plays a crucial role in the accurate modelling of dental laser ablation.

  17. Laser Ablation for Medical Applications

    NASA Astrophysics Data System (ADS)

    Hayashi, Ken-Ichi

    Medical applications of laser are measurement, laser surgery, in-situ monitoring, and processing of medical devices. In this paper, author briefly reviews the trends of medical applications, describes some new applications, and then discuss about the future trends and problems of medical applications. At present, the domestic market of laser equipment for medical applications is nearly 1/10 of that for industrial applications, which has registered significant growth continuously. Laser surgery as a minimum invasive surgery under arthroscope is expected to decrease the pain of patients. Precise processing such as cutting and welding is suitable for manufacturing medical devices. Pulsed laser deposition has been successfully applied to the thin film coating. The corneal refractive surgery by ArF excimer laser has been widely accepted for its highly safe operation. Laser ablation for retinal implant in the visual prosthesis is one of the promising applications of laser ablation in medicine. New applications with femtosecond laser are expected in the near future.

  18. Nanoparticle formation in the expansion process of a laser ablated plume

    NASA Astrophysics Data System (ADS)

    Takiya, T.; Umezu, I.; Yaga, M.; Han, M.

    2007-04-01

    In the present article, we describe the process of nanoparticle formation during pulsed laser ablation in an inert gas atmosphere. We investigated the interaction between laser ablated plumes and shock waves using one dimensional Eulerian fluid dynamics equations combined with a rate equation relating to a classical nucleation model of supersaturated vapors. The initial values for the plume immediately after laser irradiation onto a silicon target were calculated based on stochastic thermodynamics, which was first used by Houle et al. We found a certain case wherein the rate of nanoparticle formation becomes higher when a reflected shock wave passes through the plume. In that particular case, mono-dispersed nanoparticles can be generated by carrying out nucleation and nanoparticle growth as separate processes.

  19. Infrared laser bone ablation

    SciTech Connect

    Nuss, R.C.; Fabian, R.L.; Sarkar, R.; Puliafito, C.A.

    1988-01-01

    The bone ablation characteristics of five infrared lasers, including three pulsed lasers (Nd:YAG, lambda = 1064 micron; Hol:YSGG, lambda = 2.10 micron; and Erb:YAG, lambda = 2.94 micron) and two continuous-wave lasers (Nd:YAG, lambda = 1.064 micron; and CO/sub 2/, lambda = 10.6 micron), were studied. All laser ablations were performed in vitro, using moist, freshly dissected calvarium of guinea pig skulls. Quantitative etch rates of the three pulsed lasers were calculated. Light microscopy of histologic sections of ablated bone revealed a zone of tissue damage of 10 to 15 micron adjacent to the lesion edge in the case of the pulsed Nd:YAG and the Erb:YAG lasers, from 20 to 90 micron zone of tissue damage for bone ablated by the Hol:YSGG laser, and 60 to 135 micron zone of tissue damage in the case of the two continuous-wave lasers. Possible mechanisms of bone ablation and tissue damage are discussed.

  20. Modeling of laser ablation processes for thin film deposition of materials^

    NASA Astrophysics Data System (ADS)

    Leboeuf, Jean-Noel G.

    1996-05-01

    The laser ablation technique for pulsed laser deposition of thin films has proven extremely successful at growing high-quality films of very complex and novel materials, such as high temperature superconducting compounds and diamond-like carbon. The physics ingredients involved are quite complicated given that they include laser-solid interactions at the target, plasma formation off the target, vapor/plasma plume transport towards the deposition substrate, and plume-solid interactions at the substrate. A global physics and computational approach to the laser ablation process has been taken which relies on thermal models to describe laser-solid interactions; on kinetic models of plasma formation in the ablated plume; on an assorted variety of hydrodynamic, gas dynamic and collisional models of plume transport in near vacuum and in a higher pressure background gas; and on molecular dynamics methods to treat plume-substrate interactions. We have chosen to concentrate mostly on silicon to validate our models against experiments. The application of our physics results does however go beyond silicon, given the universality of many experimental observations, such as plume splitting for instance, for a wide variety of laser-ablated materials, be it carbon, copper, yttrium or YBCO. ^* In collaboration with K. R. Chen, J. M. Donato, D. B. Geohegan, C. L. Liu, A. A. Puretzky and R. F. Wood, Oak Ridge National Laboratory, Oak Ridge, TN 37831-8071 ^ Work supported by Oak Ridge National Laboratory Directed Research and Development (LDRD) Fund under U.S Department of Energy contract No. DE-AC05-96OR22464 with Lockheed Martin Energy Systems, Inc.

  1. Controlling the oxidation processes of Zn nanoparticles produced by pulsed laser ablation in aqueous solution

    NASA Astrophysics Data System (ADS)

    Camarda, P.; Messina, F.; Vaccaro, L.; Buscarino, G.; Agnello, S.; Gelardi, F. M.; Cannas, M.

    2016-09-01

    We used online UV-VIS optical absorption and photoluminescence spectra, acquired during and after pulsed laser ablation of a Zinc plate in aqueous solution, to investigate the effect of the laser repetition rate and liquid environment on the oxidation processes of the produced nanoparticles. A transient Zn/ZnO core-shell structure was revealed by the coexistence of an absorption peak around 5.0 eV due to Zn surface plasmon resonance and of an edge at 3.4 eV coming from wurtzite ZnO. The growth kinetics of ZnO at the various repetition rates, selectively probed by the excitonic emission at 3.3 eV, began immediately at the onset of laser ablation and was largely independent of the repetition rate. In addition, we detected an emission at 2.3 eV related to oxygen vacancies, which began to grow after a number of pulses increasing with the used repetition rate. Optical absorption spectra during and after ablation in a mixture of water and ethanol (0%-100%) revealed that the oxidation kinetics of Zn nanoparticles slows down from about 900 s in pure water to at least one week in pure ethanol.

  2. Review of Laser Ablation Process for Single Wall Carbon Nanotube Production

    NASA Technical Reports Server (NTRS)

    Arepalli, Sivaram

    2003-01-01

    Different types of lasers are now routinely used to prepare single wall carbon nanotubes (SWCNTs). The original method developed by researchers at Rice University utilized a "double pulse laser oven" process. A graphite target containing about 1 atomic percent of metal catalysts is ablated inside a 1473K oven using laser pulses (10 ns pulse width) in slow flowing argon. Two YAG lasers with a green pulse (532 nm) followed by an IR pulse (1064 nm) with a 50 ns delay are used for ablation. This set up produced single wall carbon nanotube material with about 70% purity having a diameter distribution peaked around 1.4 nm. The impurities consist of fullerenes, metal catalyst clusters (10 to 100 nm diameter) and amorphous carbon. The rate of production with the initial set up was about 60 mg per hour with 10Hz laser systems. Several researchers have used variations of the lasers to improve the rate, consistency and study effects of different process parameters on the quality and quantity of SWCNTs. These variations include one to three YAG laser systems (Green, Green and IR), different pulse widths (nano to microseconds as well as continuous) and different laser wavelengths (Alexandrite, CO, CO2, free electron lasers in the near to far infrared). It is noted that yield from the single laser (Green or IR) systems is only a fraction of the two laser systems. The yield seemed to scale up with the repetition rate of the laser systems (10 to 60 Hz) and depended on the beam uniformity and quality of the laser pulses. The shift to longer wavelength lasers (free electron, CO and CO2) did not improve the quality, but increased the rate of production because these lasers are either continuous (CW) or high repetition rate pulses (kHz to MHz). The average power and the peak power of the lasers seem to influence the yields. Very high peak powers (MegaWatts per square centimeter) are noted to increase ablation of bigger particles with reduced yields of SWCNTs. Increased average powers

  3. The influence of ambient medium density on laser ablation processes

    SciTech Connect

    Kilgo, III, Marvin Moses

    1995-11-01

    Interest in high flux transport processes has grown in recent years along with the ability and need to manipulate systems with microscopic length and time scales. These systems present unique engineering challenges. Because the time and length scales associated with these problems are very small, assumptions of local equilibrium, physical and mathematical smoothness of boundaries and the unambiguous definition of thermodynamic fields can not be automatically made, even though they may ultimately be acceptable. Furthermore, the observations are made on macroscopic or integrated scales. The large difference in scales between the temporal evolution of the process and the observation requires careful consideration of the claims made regarding the system`s microscopic, temporal behavior. In particular, consistency of a proposed model with observed results does not guarantee uniqueness, or predictive accuracy for the model. For these reasons, microscale heat transfer systems demand a careful consideration of the framework within which the experimentation and analysis are conducted.

  4. [Ablative and fractional lasers].

    PubMed

    Beylot, C; Grognard, C; Michaud, T

    2009-10-01

    The use of pulsed or scanning Carbon Dioxide, and pulsed Erbium-YAG lasers allows the programmable and reproducible photocoagulation of thin layers of the epidermis and superficial dermis. Thermal damage depends on the type of laser and is greater with CO(2) lasers. The degree of neocollagenesis is proportional to the thermal damage and is better with CO(2) lasers. Their main indication is the correction of photoaged facial skin but they can also be used for corrective dermatology, e.g. for scars and genodermatosis. Results are highly satisfactory but the technique is invasive and the patient experiences a social hindrance of around two weeks. Fractionated techniques treat 25% of the defective skin area at each session in noncontiguous microzones; four sessions are therefore necessary to treat the entire cutaneous surface. The treatment is given under topical anesthesia and is much less invasive, particularly with nonablative fractional laser treatment in which photothermolysis does not penetrate below the epidermis and/or the effects are slight, with no or very little social isolation. However, the results are much less satisfactory than the results of ablative laser and there is no firming effect. Other zones than the face can be treated. With the fractional CO(2) and Erbium ablative lasers, which have multiplied over the past 2 years, the much wider impacts cause perforation of the epidermis and there is a zone of ablation by laser photovaporization, with a zone of thermal damage below. The results are better in correcting photoaging of the face, without, however, achieving the efficacy of ablative lasers, which remain the reference technique. However, the effects are not insignificant, requiring at least 5 days of social isolation.

  5. Properties of the ablation process for excimer laser ablation of Y sub 1 Ba sub 2 Cu sub 3 O sub 7

    SciTech Connect

    Neifeld, R.A.; Potenziani, E. ); Sinclair, W.R. ); Hill III, W.T.; Turner, B.; Pinkas, A. )

    1991-01-15

    The process of excimer laser ablation has been studied while varying the laser fluence from 0.237 to 19.1 J/cm{sup 2}. Ion time-of-flight, total charge, target etch depth per pulse, and etch volume per pulse have been measured. Results indicate a maximum ablation volume and minimum ionization fraction occur near 5 J/cm{sup 2}. Several of the parameters measured vary rapidly in the 1--5 J/cm{sup 2} range. Variation in these parameters strongly influences the properties of films grown by this technique.

  6. OCDR guided laser ablation device

    DOEpatents

    Dasilva, Luiz B.; Colston, Jr., Bill W.; James, Dale L.

    2002-01-01

    A guided laser ablation device. The device includes a mulitmode laser ablation fiber that is surrounded by one or more single mode optical fibers that are used to image in the vicinity of the laser ablation area to prevent tissue damage. The laser ablation device is combined with an optical coherence domain reflectometry (OCDR) unit and with a control unit which initializes the OCDR unit and a high power laser of the ablation device. Data from the OCDR unit is analyzed by the control unit and used to control the high power laser. The OCDR images up to about 3 mm ahead of the ablation surface to enable a user to see sensitive tissue such as a nerve or artery before damaging it by the laser.

  7. Chemical models for simulating single-walled nanotube production in arc vaporization and laser ablation processes

    NASA Technical Reports Server (NTRS)

    Scott, Carl D.

    2004-01-01

    Chemical kinetic models for the nucleation and growth of clusters and single-walled carbon nanotube (SWNT) growth are developed for numerical simulations of the production of SWNTs. Two models that involve evaporation and condensation of carbon and metal catalysts, a full model involving all carbon clusters up to C80, and a reduced model are discussed. The full model is based on a fullerene model, but nickel and carbon/nickel cluster reactions are added to form SWNTs from soot and fullerenes. The full model has a large number of species--so large that to incorporate them into a flow field computation for simulating laser ablation and arc processes requires that they be simplified. The model is reduced by defining large clusters that represent many various sized clusters. Comparisons are given between these models for cases that may be applicable to arc and laser ablation production. Solutions to the system of chemical rate equations of these models for a ramped temperature profile show that production of various species, including SWNTs, agree to within about 50% for a fast ramp, and within 10% for a slower temperature decay time.

  8. Pulsed infrared laser ablation and clinical applications

    NASA Astrophysics Data System (ADS)

    Chan, Kin Foong

    -running pulsed Ho:YAG laser in lithotripsy. Results indicated that a photothermal ablative process with concomitant chemical decomposition of calculus components occurred. This discovery dispelled the hypothesis that laser lithotripsy fragments calculus by means of shockwaves. Finally, the Er:YAG laser was explored for use in laser lithotripsy. Preliminary mass loss measurements suggested that the Er:YAG laser was more efficient than the Ho:YAG laser for lithotripsy.

  9. Including parameterization of the discrete ablation process into a planning and simulation environment for robot-assisted laser osteotomy.

    PubMed

    Burgner, Jessica; Kahrs, Lüder Alexander; Raczkowsky, Jörg; Wörn, Heinz

    2009-01-01

    Material processing using laser became a widely used method especially in the scope of industrial automation. The systems are mostly based on a precise model of the laser process and the according parameterization. Beside the industrial use the laser as an instrument to treat human tissue has become an integral part in medicine as well. Human tissue as an inhomogeneous material to process, poses the question of how to determine a model, which reflects the interaction processes with a specific laser.Recently it could be shown that the pulsed CO2 laser is suitable to ablate bony and cartilage tissue. Until now this thermo-mechanical bone ablation is not characterized as a discrete process. In order to plan and simulate the ablation process in the correct level of detail, the parameterization is indispensable. We developed a planning and simulation environment, determined parameters by confocal measurements of bony specimen and use these results to transfer planned cutting trajectories into a pulse sequence and corresponding robot locations.

  10. Laser ablation in analytical chemistry - A review

    SciTech Connect

    Russo, Richard E.; Mao, Xianglei; Liu, Haichen; Gonzalez, Jhanis; Mao, Samuel S.

    2001-10-10

    Laser ablation is becoming a dominant technology for direct solid sampling in analytical chemistry. Laser ablation refers to the process in which an intense burst of energy delivered by a short laser pulse is used to sample (remove a portion of) a material. The advantages of laser ablation chemical analysis include direct characterization of solids, no chemical procedures for dissolution, reduced risk of contamination or sample loss, analysis of very small samples not separable for solution analysis, and determination of spatial distributions of elemental composition. This review describes recent research to understand and utilize laser ablation for direct solid sampling, with emphasis on sample introduction to an inductively coupled plasma (ICP). Current research related to contemporary experimental systems, calibration and optimization, and fractionation is discussed, with a summary of applications in several areas.

  11. Modeling of the shrinking process of a bubble induced by laser metal ablation in water and experimental verification

    NASA Astrophysics Data System (ADS)

    Dabir-Moghaddam, Navid; Liu, Ze; Wu, Benxin

    2017-01-01

    Laser ablation of a solid target immersed in liquid (such as water) has many important applications such as laser synthesis of nanoparticles, laser micromachining in water, and laser shock peening. Laser ablation of a solid target in water involves complicated physical processes. One important process often involved is the generation and evolution of a bubble in water and attached to the target surface, which may have significant effects on the target and the ambient water, and hence may greatly affect the relevant practical applications. Some experimental studies were reported in the literature on bubble evolutions induced by laser ablation of a solid target in water. However, the reported previous relevant physics-based modeling work is not sufficient. A physics-based model may help improve the process fundamental understanding and generate valuable information to related applications. In this paper, physics-based modeling work has been performed on the shrinking process of a bubble induced by laser metal ablation in water, together with time-resolved shadowgraph imaging experiments to verify the model. The model-predicted bubble evolution agrees reasonably well with the experimental measurement shown in the paper. Under the studied conditions, it has been found that near the bubble collapse moment (i.e., the moment when the bubble shrinks to a minimum size): (1) the bubble shrinks very fast, and the peak fluid velocity magnitude occurs inside the bubble and can exceed ˜550 m/s; (2) the temperature inside the bubble increases very quickly and approaches ˜2000 K; and (3) the pressure inside the bubble becomes very high, and can reach a peak magnitude of ˜380 MPa at the collapse moment at the bubble center. During the shrinking process, a high-pressure region outside and near the bubble wall is generated near the collapse moment, but the temperature of the region outside the bubble mostly remains low.

  12. Probing mesoscopic process of laser ablation in liquid by integrated method of optical beam deflection and time-resolved shadowgraphy.

    PubMed

    Chen, Jun; Li, Xiaoming; Gu, Yu; Wang, Hao; Song, Xiufeng; Zeng, Haibo

    2017-03-01

    For nanomaterial fabrication by laser ablation in liquid (LAL), it is very important to understand the mesoscopic process of laser interaction with materials in liquid. We proposed a method combining time-resolved shadowgraphy and optical beam deflection method to study the LAL process in both pure water and water with nanoparticles (colloids). As the laser was focused on the target in pure water, the laser energy was absorbed by the target and plasma, shockwaves and bubbles were produced, along with the generation of nanoparticles. While in case of colloid, laser beam first passed through the solution, interacted with nanoparticles and induced plenty of sporadic shadows (small bubbles) on the beam path which were captured by shadowgraphy. Then, the laser arrived at the target and induced breakdown accompanied by the emergence of plasma, shockwave and bubbles. Meanwhile, the concentration of nanoparticle increased and the sizes of nanoparticle were modified. The radius and oscillation time of bubbles are much smaller in the colloid than that in pure water, mainly due to laser energy loss by breakdown of the nanoparticles and generation of small bubbles before reaching the target. Moreover, we found the maximum bubble radius and bubble oscillation time decrease quickly with laser irradiation times at the beginning, and then reach a plateau, because of laser energy lost on the way to the target. In addition, we used the ablation process to explain a bimodal size distribution of nanoparticles. This work will deepen our understanding on the mechanism of both laser ablation of bulk targets in liquid and laser irradiation of particles in liquid.

  13. Laser ablation in analytical chemistry.

    PubMed

    Russo, Richard E; Mao, Xianglei; Gonzalez, Jhanis J; Zorba, Vassilia; Yoo, Jong

    2013-07-02

    In 2002, we wrote an Analytical Chemistry feature article describing the Physics of Laser Ablation in Microchemical Analysis. In line with the theme of the 2002 article, this manuscript discusses current issues in fundamental research, applications based on detecting photons at the ablation site (LIBS and LAMIS) and by collecting particles for excitation in a secondary source (ICP), and directions for the technology.

  14. Highspeed laser ablation cutting of metal

    NASA Astrophysics Data System (ADS)

    Ullmann, F.; Loeschner, U.; Hartwig, L.; Szczepanski, D.; Schille, J.; Gronau, S.; Knebel, T.; Drechsel, J.; Ebert, R.; Exner, H.

    2013-02-01

    In laser ablation cutting, irradiation of high-intense laser beams causes ejection of molten and evaporated material out of the cutting zone as a result of high pressure gradients, induced by expanding plasma plumes. This paper investigates highspeed laser ablation cutting of industrial grade metal sheets using high-brilliant continuous wave fiber lasers with output powers up to 5 kW. The laser beam was deflected with scan speeds up to 2700 m/min utilizing both a fast galvanometer scan system and a polygon scan system. By sharp laser beam focusing using different objectives with focal lengths ranging between 160 mm and 500 mm, small laser spot diameters between 16.5 μm and 60 μm were obtained, respectively. As a result high peak intensities between 3*108 W/cm² and 2.5*109 W/cm² were irradiated on the sample surface, and cutting kerfs with a maximum depth of 1.4 mm have been produced. In this study the impact of the processing parameters laser power, laser spot diameter, cutting speed, and number of scans on both the achievable cutting depth and the cutting edge quality was investigated. The ablation depths, the heights of the cutting burr, as well as the removed material volumes were evaluated by means of optical microscope images and cross section photographs. Finally highspeed laser ablation cutting was studied using an intensified ultra highspeed camera in order to get useful insights into the cutting process.

  15. Online monitoring of nanoparticles formed during nanosecond laser ablation

    NASA Astrophysics Data System (ADS)

    Nováková, Hana; Holá, Markéta; Vojtíšek-Lom, Michal; Ondráček, Jakub; Kanický, Viktor

    2016-11-01

    The particle size distribution of dry aerosol originating from laser ablation of glass material was monitored simultaneously with Laser Ablation - Inductively Coupled Plasma Mass Spectrometry (LA-ICP-MS) analysis and two aerosol spectrometers - Fast Mobility Particle Sizer (FMPS) and Aerodynamic Particle Sizer (APS). The unique combination of LA-ICP-MS and FMPS offers the possibility of measuring the particle size distribution every 1 s of the ablation process in the size range of 5.6-560 nm. APS extends the information about particle concentration in the size range 0.54-17 μm. Online monitoring of the dry aerosol was performed for two ablation modes (spot and line with a duration of 80 s) with a 193 nm excimer laser system, using the glass reference material NIST 610 as a sample. Different sizes of laser spot for spot ablation and different scan speeds for line ablation were tested. It was found that the FMPS device is capable of detecting changes in particle size distribution at the first pulses of spot laser ablation and is suitable for laser ablation control simultaneously with LA-ICP-MS analysis. The studied parameters of laser ablation have an influence on the resulting particle size distribution. The line mode of laser ablation produces larger particles during the whole ablation process, while spot ablation produces larger particles only at the beginning, during the ablation of the intact layer of the ablated material. Moreover, spot ablation produces more primary nano-particles (in ultrafine mode size range < 100 nm) than line ablation. This effect is most probably caused by a reduced amount of large particles released from the spot ablation crater. The larger particles scavenge the ultrafine particles during the line ablation mode.

  16. From Laser Desorption to Laser Ablation of Biopolymers

    NASA Astrophysics Data System (ADS)

    Franz, Hillenkamp

    1998-03-01

    For selected indications laser ablation and cutting of biological tissues is clinical practice. Preferentially lasers with emission wavelengths in the far UV and the mid IR are used, for which tissue absorption is very high. Morphologically the ablation sites look surprisingly similar for the two wavelength ranges, despite of the very different prim y putative interaction mechanisms. Ablation depth as a function of fluence follows a sigmoidal curve. Even factors below the nominal ablation threshold superficial layers of material get removed from the surface. This is the fluence range for Matrix-Assisted Laser Desorption/Ionization (MALDI). Evidence will be presented which suggest that strong similarities exist between the desorption and ablation processes both for UV- as well as for IR-wavelengths.

  17. Analysis of process parameter for the ablation of optical glasses with femto- and picosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Schindler, Christian; Friedrich, Maria; Bliedtner, Jens

    2016-03-01

    Experiments with an ultrashort pulsed laser system emitting pulses ranging from 350 fs to 10 ps and a maximum average power of 50 W at 1030 nm are presented. The laser beam gets deflected by a galvanometric scan-system with maximum scan speed of 2500 mm/s and focused by F-theta lenses onto the substrates. By experiments the influences of pulse energy, fluence, laser wavelength, pulse length and material conditions on the target figures is analyzed. These are represented by the material characteristics mean squared roughness, ablation depths as well as the microcrack distribution in depth. The experimental procedure is applied onto a series of fused silica and SF6 samples.

  18. The Post-Processing Effects due to Pulsed Laser Ablation of Paper

    NASA Astrophysics Data System (ADS)

    Kaminska, A.; Sawczak, M.; Cieplnski, M.; Sliwinski, G.

    For contemporary samples the effect of pulsed laser ablation applied at wavelengths selected from the range UV — near IR of 266, 355, 532 and 1064 nm were investigated. All the samples were made by the same method and of the same material, i.e. mixture of pure cotton cellulose and wood-pulp. Results of the colorimetric measurements indicate the most effective surface cleaning at 532 nm for the artificially soiled samples. An artificial aging resulted in neglectable changes in lightness and yellowness of the laser cleaned laboratory soiled samples but influenced the changes in non soiled samples. Marked changes were noticed due to 266 nm, 355 nm and 1064 nm irradiation and were ascribed to the photochemical damage of the cellulose fibres and to enhanced absorption of the laser radiation by the soil particles.

  19. Laser ablation based fuel ignition

    DOEpatents

    Early, James W.; Lester, Charles S.

    1998-01-01

    There is provided a method of fuel/oxidizer ignition comprising: (a) application of laser light to a material surface which is absorptive to the laser radiation; (b) heating of the material surface with the laser light to produce a high temperature ablation plume which emanates from the heated surface as an intensely hot cloud of vaporized surface material; and (c) contacting the fuel/oxidizer mixture with the hot ablation cloud at or near the surface of the material in order to heat the fuel to a temperature sufficient to initiate fuel ignition.

  20. Laser ablation based fuel ignition

    DOEpatents

    Early, J.W.; Lester, C.S.

    1998-06-23

    There is provided a method of fuel/oxidizer ignition comprising: (a) application of laser light to a material surface which is absorptive to the laser radiation; (b) heating of the material surface with the laser light to produce a high temperature ablation plume which emanates from the heated surface as an intensely hot cloud of vaporized surface material; and (c) contacting the fuel/oxidizer mixture with the hot ablation cloud at or near the surface of the material in order to heat the fuel to a temperature sufficient to initiate fuel ignition. 3 figs.

  1. Superconducting thin films of Bi-Sr-Ca-Cu-O obtained by laser ablation processing

    SciTech Connect

    Kim, B.F.; Bohandy, J.; Phillips, T.E.; Green, W.J.; Agostinelli, E.; Adrian, F.J.; Moorjani, K.; Swartzendruber, L.J.; Shull, R.D.; Bennett, L.H.; and others

    1988-07-25

    Thin films of Bi-Sr-Ca-Cu-O, deposited on (100) cubic zirconia by laser ablation from a bulk superconducting target of nominal composition BiSrCaCu/sub 2/ O/sub x/ , have been investigated by dc resistance and magnetically modulated microwave absorption measurements. The latter technique reveals important features regarding the phase purity of superconducting samples that are masked in the dc resistance measurements. The superconducting behavior of the films, as a function of the substrate temperature during deposition and the post-deposition annealing conditions, is discussed.

  2. Coupled molecular dynamics-Monte Carlo model to study the role of chemical processes during laser ablation of polymeric materials.

    PubMed

    Prasad, Manish; Conforti, Patrick F; Garrison, Barbara J

    2007-08-28

    The coarse grained chemical reaction model is enhanced to build a molecular dynamics (MD) simulation framework with an embedded Monte Carlo (MC) based reaction scheme. The MC scheme utilizes predetermined reaction chemistry, energetics, and rate kinetics of materials to incorporate chemical reactions occurring in a substrate into the MD simulation. The kinetics information is utilized to set the probabilities for the types of reactions to perform based on radical survival times and reaction rates. Implementing a reaction involves changing the reactants species types which alters their interaction potentials and thus produces the required energy change. We discuss the application of this method to study the initiation of ultraviolet laser ablation in poly(methyl methacrylate). The use of this scheme enables the modeling of all possible photoexcitation pathways in the polymer. It also permits a direct study of the role of thermal, mechanical, and chemical processes that can set off ablation. We demonstrate that the role of laser induced heating, thermomechanical stresses, pressure wave formation and relaxation, and thermochemical decomposition of the polymer substrate can be investigated directly by suitably choosing the potential energy and chemical reaction energy landscape. The results highlight the usefulness of such a modeling approach by showing that various processes in polymer ablation are intricately linked leading to the transformation of the substrate and its ejection. The method, in principle, can be utilized to study systems where chemical reactions are expected to play a dominant role or interact strongly with other physical processes.

  3. Laser ablation ICP-MS applications using the timescales of geologic and biologic processes

    NASA Astrophysics Data System (ADS)

    Ridley, W. I.

    2003-04-01

    Geochemists commonly examine geologic processes on timescales of 10^4--10^9 years, and accept that often age relations, e.g., chemical zoning in minerals, can only be measured in a relative sense. The progression of a geologic process that involves geochemical changes may be assessed using trace element microbeam techniques, because the textural, and therefore spatial context, of the analytical scheme can be preserved. However, quantification requires appropriate calibration standards. Laser ablation ICP-MS (LA-ICP-MS) is proving particularly useful now that appropriate standards are becoming available. For instance, trace element zoning patterns in primary sulfides (e.g., pyrite, sphalerite, chalcopyrite, galena) and secondary phases can be inverted to examine relative changes in fluid composition during cycles of hydrothermal mineralization. In turn such information provides insights into fluid sources, migration pathways and depositional processes. These studies have only become possible with the development of appropriate sulfide calibration standards. Another example, made possible with the development of appropriate silicate calibration standards, is the quantitative spatial mapping of REE variations in amphibolite-grade garnets. The recognition that the trace and major elements are decoupled provides a better understanding of the various sources of elements during metamorphic re-equilibration. There is also a growing realization that LA-ICP-MS has potential in biochemical studies, and geochemists have begun to turn their attention in this direction, working closely with biologists. Unlike many geologic processes, the timescales of biologic processes are measured in years to centuries and are frequently amenable to absolute dating. Examples that can be cited where LA-ICP-MS has been applied include annual trace metal variations in tree rings, corals, teeth, bones, bird feathers and various animal vibrissae (sea lion, walrus, wolf). The aim of such studies is

  4. Microfabrication with femtosecond laser processing : (A) laser ablation of ferrous alloys, (B) direct-write embedded optical waveguides and integrated optics in bulk glasses.

    SciTech Connect

    Guo, Junpeng; McDaniel, Karen Lynn; Palmer, Jeremy Andrew; Yang, Pin; Griffith, Michelle Lynn; Vawter, Gregory Allen; Harris, Marc F.; Tallant, David Robert; Luk, Ting Shan; Burns, George Robert

    2004-11-01

    At Sandia National Laboratories, miniaturization dominates future hardware designs, and technologies that address the manufacture of micro-scale to nano-scale features are in demand. Currently, Sandia is developing technologies such as photolithography/etching (e.g. silicon MEMS), LIGA, micro-electro-discharge machining (micro-EDM), and focused ion beam (FIB) machining to fulfill some of the component design requirements. Some processes are more encompassing than others, but each process has its niche, where all performance characteristics cannot be met by one technology. For example, micro-EDM creates highly accurate micro-scale features but the choice of materials is limited to conductive materials. With silicon-based MEMS technology, highly accurate nano-scale integrated devices are fabricated but the mechanical performance may not meet the requirements. Femtosecond laser processing has the potential to fulfill a broad range of design demands, both in terms of feature resolution and material choices, thereby improving fabrication of micro-components. One of the unique features of femtosecond lasers is the ability to ablate nearly all materials with little heat transfer, and therefore melting or damage, to the surrounding material, resulting in highly accurate micro-scale features. Another unique aspect to femtosecond radiation is the ability to create localized structural changes thought nonlinear absorption processes. By scanning the focal point within transparent material, we can create three-dimensional waveguides for biological sensors and optical components. In this report, we utilized the special characteristics of femtosecond laser processing for microfabrication. Special emphasis was placed on the laser-material interactions to gain a science-based understanding of the process and to determine the process parameter space for laser processing of metals and glasses. Two areas were investigated, including laser ablation of ferrous alloys and direct

  5. Laser ablation studies of concrete

    SciTech Connect

    Savina, M.; Xu, Z.; Wang, Y.; Reed, C.; Pellin, M.

    1999-10-20

    Laser ablation was studied as a means of removing radioactive contaminants from the surface and near-surface regions of concrete. The authors present the results of ablation tests on cement and concrete samples using a 1.6 kW pulsed Nd:YAG laser with fiber optic beam delivery. The laser-surface interaction was studied using cement and high density concrete as targets. Ablation efficiency and material removal rates were determined as functions of irradiance and pulse overlap. Doped samples were also ablated to determine the efficiency with which surface contaminants were removed and captured in the effluent. The results show that the cement phase of the material melts and vaporizes, but the aggregate portion (sand and rock) fragments. The effluent consists of both micron-size aerosol particles and chunks of fragmented aggregate material. Laser-induced optical emission spectroscopy was used to analyze the surface during ablation. Analysis of the effluent showed that contaminants such as cesium and strontium were strongly segregated into different regions of the particle size distribution of the aerosol.

  6. Laser Ablated Carbon Nanodots for Light Emission.

    PubMed

    Reyes, Delfino; Camacho, Marco; Camacho, Miguel; Mayorga, Miguel; Weathers, Duncan; Salamo, Greg; Wang, Zhiming; Neogi, Arup

    2016-12-01

    The synthesis of fluorescent carbon dots-like nanostructures (CNDs) obtained through the laser ablation of a carbon solid target in liquid environment is reported. The ablation process was induced in acetone with laser pulses of 1064, 532, and 355 nm under different irradiation times. Close-spherical amorphous CNDs with sizes between 5 and 20 nm, whose abundance strongly depends on the ablation parameters were investigated using electron microscopy and was confirmed using absorption and emission spectroscopies. The π- π* electronic transition at 3.76 eV dominates the absorption for all the CNDs species synthesized under different irradiation conditions. The light emission is most efficient due to excitation at 3.54 eV with the photoluminescence intensity centered at 3.23 eV. The light emission from the CNDs is most efficient due to ablation at 355 nm. The emission wavelength of the CNDs can be tuned from the near-UV to the green wavelength region by controlling the ablation time and modifying the ablation and excitation laser wavelength.

  7. Femtosecond laser ablation of enamel

    NASA Astrophysics Data System (ADS)

    Le, Quang-Tri; Bertrand, Caroline; Vilar, Rui

    2016-06-01

    The surface topographical, compositional, and structural modifications induced in human enamel by femtosecond laser ablation is studied. The laser treatments were performed using a Yb:KYW chirped-pulse-regenerative amplification laser system (560 fs and 1030 nm) and fluences up to 14 J/cm2. The ablation surfaces were studied by scanning electron microscopy, grazing incidence x-ray diffraction, and micro-Raman spectroscopy. Regardless of the fluence, the ablation surfaces were covered by a layer of resolidified material, indicating that ablation is accompanied by melting of hydroxyapatite. This layer presented pores and exploded gas bubbles, created by the release of gaseous decomposition products of hydroxyapatite (CO2 and H2O) within the liquid phase. In the specimen treated with 1-kHz repetition frequency and 14 J/cm2, thickness of the resolidified material is in the range of 300 to 900 nm. The micro-Raman analysis revealed that the resolidified material contains amorphous calcium phosphate, while grazing incidence x-ray diffraction analysis allowed detecting traces of a calcium phosphate other than hydroxyapatite, probably β-tricalcium phosphate Ca3), at the surface of this specimen. The present results show that the ablation of enamel involves melting of enamel's hydroxyapatite, but the thickness of the altered layer is very small and thermal damage of the remaining material is negligible.

  8. Laser ablation of gall bladder stones

    NASA Astrophysics Data System (ADS)

    Marafi, M.; Makdisi, Y.; Bhatia, K. S.; Abdulah, A. H.; Kokaj, Y.; Mathew, K.; Quinn, F.; Qabazard, A.

    1999-06-01

    Study of laser interaction with calculi is presented. A system of Nd-Yag and Ho-Yag pulsed lasers were used to produce fluorescence and plasma signals at the stone surface surrounded by saline and bile fluids. Fourth harmonic from Nd-Yag laser was transmitted to the samples by graded UV optical fibres. Gall bladder stones of various compositions were subjected to the high power Ho-Yag laser. Temporal transients and spectral evolution of plasma and fluorescence signals were monitored by a streak camera. A profile of acoustic pressures generated by shock waves was recorded with sensitive hydrophones placed in the surrounding fluids. Ablation threshold, cavitation process and fluorescence dependence on the laser parameters were studied in detail. Potential of stone identification by fluorescence and possible hydrodynamic model for ablation of biological samples is discussed.

  9. Effects of laser ablation on cemented tungsten carbide surface quality

    NASA Astrophysics Data System (ADS)

    Tan, J. L.; Butler, D. L.; Sim, L. M.; Jarfors, A. E. W.

    2010-11-01

    Although laser micromachining has been touted as being the most promising way to fabricate micro tools, there has been no proper evaluation of the effects of laser ablation on bulk material properties. The current work demonstrates the effects of laser ablation on the properties of a cemented tungsten carbide surface. Of particular interest is the resultant increase in compressive residual stresses in the ablated surface. From this study it is seen that there are no adverse effects from laser ablation of cemented tungsten carbide that would preclude its use for the fabrication of micro-tools but a finishing process may not be avoidable.

  10. Molecular dynamics investigation of mechanisms of femtosecond laser ablation

    NASA Astrophysics Data System (ADS)

    Cheng, Changrui

    Laser micro-machining has been widely applied for material processing in many industries. A phenomenon called "laser ablation" is usually involved in the laser micro-machining process. Laser ablation is the process of material removal after the irradiation of a laser beam onto the material. It is commonly characterized by small temporal and spatial scales, extremely high material temperature and pressure, and strong non-equilibrium thermodynamic state. In this work, molecular dynamics (MD) simulation is conducted to study the femtosecond laser ablation of metals (nickel and copper) and dielectrics (fused silica, or glass). The laser heating and the ablation processes are numerically modeled, and the computation is accelerated by parallel processing technique. Both the pair-wise Morse potential and the many-body EAM (Embedded-Atom Method) potential are employed for metals. In the simulation of fused silica, the BKS (van Beest, Kramer and van Santen) potential is used, and the generation of free electrons, the energy transport from laser beam to free electrons and energy coupling between electrons and the lattice are considered. The main goal of this work is to illustrate the detailed processes of femtosecond laser ablation and to study its mechanisms. From the MD results, it is found that the mechanism of femtosecond laser ablation is strongly dependent on the laser fluences. For metals, low fluence laser ablation is mainly through phase explosion (homogeneous gas bubble nucleation), while spinodal decomposition is responsible for high fluence ablation. Ablation mechanism is determined by whether or not the material (liquid) temperature exceeds the critical temperature. For fused silica, the generation and existence of free electrons are found to affect ablation significantly, especially at low fluence, where Coulomb explosion is found to play an important role in material separation.

  11. A Compact, Solid-State UV (266 nm) Laser System Capable of Burst-Mode Operation for Laser Ablation Desorption Processing

    NASA Technical Reports Server (NTRS)

    Arevalo, Ricardo, Jr.; Coyle, Barry; Paulios, Demetrios; Stysley, Paul; Feng, Steve; Getty, Stephanie; Binkerhoff, William

    2015-01-01

    Compared to wet chemistry and pyrolysis techniques, in situ laser-based methods of chemical analysis provide an ideal way to characterize precious planetary materials without requiring extensive sample processing. In particular, laser desorption and ablation techniques allow for rapid, reproducible and robust data acquisition over a wide mass range, plus: Quantitative, spatially-resolved measurements of elemental and molecular (organic and inorganic) abundances; Low analytical blanks and limits-of-detection ( ng g-1); and, the destruction of minimal quantities of sample ( g) compared to traditional solution and/or pyrolysis analyses (mg).

  12. Laser Ablation Molecular Isotopic Spectrometry

    NASA Astrophysics Data System (ADS)

    Russo, Richard E.; Bol'shakov, Alexander A.; Mao, Xianglei; McKay, Christopher P.; Perry, Dale L.; Sorkhabi, Osman

    2011-02-01

    A new method of performing optical isotopic analysis of condensed samples in ambient air and at ambient pressure has been developed: Laser Ablation Molecular Isotopic Spectrometry (LAMIS). The technique uses radiative transitions from molecular species either directly vaporized from a sample or formed by associative mechanisms of atoms or ions in a laser ablation plume. This method is an advanced modification of a known atomic emission technique called laser-induced breakdown spectroscopy (LIBS). The new method — LAMIS — can determine not only chemical composition but also isotopic ratios of elements in the sample. Isotopic measurements are enabled by significantly larger isotopic shifts found in molecular spectra relative to atomic spectra. Analysis can be performed from a distance and in real time. No sample preparation or pre-treatment is required. Detection of the isotopes of hydrogen, boron, carbon, and oxygen are discussed to illustrate the technique.

  13. Temporal and spectral analysis of laser induced plasma in the ablation process of flexible printed circuit board

    NASA Astrophysics Data System (ADS)

    Ryoo, Hoon C.; Kim, Seok; Hahn, Jae W.

    2008-02-01

    Flexible printed circuit board (FPCB), consisting of copper sheets laminated onto non conductive film substrates with multiple structures, are core elements in electronics with their flexibility and capability of high density 3 dimensional wiring characteristics. In laser applied FPCB processing, a better understanding of the ablation mechanism leads to precision control of the depth processing especially by monitoring of the material transition layer. For this purpose, here we investigate the temporal and spectral behavior of the plasma plum generated on the single sided structure of FPCB using the technique of laser induced breakdown spectroscopy (LIBS). Using KrF excimer laser, the characteristic spectral emission lines of C II swan band at the wavelength of 516.5 nm and neutral copper at the wavelength range from 510 nm to 522 nm are acquired under ambient pressure in the ablation process of polyimide film and copper coated layer respectively. From a time delay from 50 ns to 4.05 μs from the beginning of the laser pulse, the temporal profiles of the spectral intensity are obtained in steps of 200 ns, which have a tendency of exponential decrease on both C II and neutral copper. In particular, we concentrate our attention on the temporal intensity behavior of the Bremsstrahlung continuum emission that decides the proper set of detection time window, by which the monitoring sensitivity of LIBS is determined. Finally, using the information of the temporal analysis for each molecular, atomic, and continuum emission, the transition layer between polyimide and copper film is distinguished by their characteristic peak information.

  14. Depth Profiling of Polymer Composites by Ultrafast Laser Ablation

    NASA Astrophysics Data System (ADS)

    Young, Christopher; Clayton, Clive; Longtin, Jon

    2009-03-01

    Past work has shown femtosecond laser ablation to be an athermal process at low fluences in polymer systems. The ablation rate in this low fluence regime is very low, allowing for micro-scale removal of material. We have taken advantage of this fact to perform shallow depth profiling ablation on carbon fiber reinforced polymer (CFRP) composites. Neat composite and resin samples were studied to establish reference ablation profiles. These profiles and the effects of the heterogeneous distribution of carbon fibers were observed through confocal laser profilometry and optical and scanning electron microscopy. Weathered materials that have been subjected to accelerated tests in artificial sunlight or water conditions were ablated to determine the correlation between exposure and change in ablation characteristics. Preliminary Raman and micro-ATR analysis performed before and after ablation shows no chemical changes indicative of thermal effects. The low-volume-ablation property was utilized in an attempt to expose the sizing-matrix interphase for analysis.

  15. Fractional ablative laser skin resurfacing: a review.

    PubMed

    Tajirian, Ani L; Tarijian, Ani L; Goldberg, David J

    2011-12-01

    Ablative laser technology has been in use for many years now. The large side effect profile however has limited its use. Fractional ablative technology is a newer development which combines a lesser side effect profile along with similar efficacy. In this paper we review fractional ablative laser skin resurfacing.

  16. Approximate model for laser ablation of carbon

    NASA Astrophysics Data System (ADS)

    Shusser, Michael

    2010-08-01

    The paper presents an approximate kinetic theory model of ablation of carbon by a nanosecond laser pulse. The model approximates the process as sublimation and combines conduction heat transfer in the target with the gas dynamics of the ablated plume which are coupled through the boundary conditions at the interface. The ablated mass flux and the temperature of the ablating material are obtained from the assumption that the ablation rate is restricted by the kinetic theory limitation on the maximum mass flux that can be attained in a phase-change process. To account for non-uniform distribution of the laser intensity while keeping the calculation simple the quasi-one-dimensional approximation is used in both gas and solid phases. The results are compared with the predictions of the exact axisymmetric model that uses the conservation relations at the interface derived from the momentum solution of the Boltzmann equation for arbitrary strong evaporation. It is seen that the simpler approximate model provides good accuracy.

  17. Printable Nanophotonic Devices via Holographic Laser Ablation.

    PubMed

    Zhao, Qiancheng; Yetisen, Ali K; Sabouri, Aydin; Yun, Seok Hyun; Butt, Haider

    2015-09-22

    Holography plays a significant role in applications such as data storage, light trapping, security, and biosensors. However, conventional fabrication methods remain time-consuming, costly, and complex, limiting the fabrication of holograms and their extensive use. Here, we demonstrate a single-pulse laser ablation technique to write parallel surface gratings and Fresnel zone plates. We utilized a 6 ns high-energy green laser pulse to form interference patterns to record a surface grating with 820 nm periodicity and asymmetric zone plate holograms on 4.5 nm gold-coated substrates. The holographic recording process was completed within seconds. The optical characteristics of the interference patterns have been computationally modeled, and well-ordered polychromatic diffraction was observed from the fabricated holograms. The zone plate showed a significant diffraction angle of 32° from the normal incident for the focal point. The nanosecond laser interference ablation for rapid hologram fabrication holds great potential in a vast range of optical devices.

  18. Ablation of steel using picosecond laser pulses in burst mode

    NASA Astrophysics Data System (ADS)

    Lickschat, Peter; Demba, Alexander; Weissmantel, Steffen

    2017-02-01

    Results obtained in picosecond laser processing of steel applying the burst mode are presented. Using the burst mode, pulse trains, i.e., bursts, consisting of a number of picosecond pulses with an inter-pulse delay of 12.5 ns and 10 ps pulse duration are applied for material processing. Small cavities with sizes in the range of the laser beam diameter made by single-burst ablation are compared to quadratic cavities of 0.5 × 0.5 mm² produced by multiburst ablation and simultaneous scanning of the laser beam across the steel sample surface. The ablated volume per pulse within the burst was calculated either from the ablated volume per burst or from the ablation depth of the quadratic cavities. With the second to fourth pulses in the bursts, a reduction of the ablated volume per pulse in comparison with the first pulse in the bursts (i.e., to the use of single pulses) was found for both single- and multiburst ablation, which is assumed to be due to plasma shielding. By contrast, the ablated volume per pulse within the bursts increases for the fifth to eighth pulses. Heat accumulation effect and the influence of the heated plasma can be assumed to be the reason for these higher ablation rates. SEM micrographs also show that there is a higher melt ejection out of the laser processed area. This is indicated by the formation of bulges about the ablated area.

  19. Influence of the Liquid on Femtosecond Laser Ablation of Iron

    NASA Astrophysics Data System (ADS)

    Kanitz, A.; Hoppius, J. S.; Gurevich, E. L.; Ostendorf, A.

    Ultrashort pulse laser ablation has become a very important industrial method for highly precise material removal ranging from sensitive thin film processing to drilling and cutting of metals. Over the last decade, a new method to produce pure nanoparticles emerged from this technique: Pulsed Laser Ablation in Liquids (PLAL). By this method, the ablation of material by a laser beam is used to generate a metal vapor within the liquid in order to obtain nanoparticles from its recondensation process. It is well known that the liquid significantly alters the ablation properties of the substrate, in our case iron. For example, the ablation rate and crater morphology differ depending on the used liquid. We present our studies on the efficiency and quality of ablated grooves in water, methanol, acetone, ethanol and toluene. The produced grooves are investigated by means of white-light interferometry, EDX and SEM.

  20. Effective temperatures of polymer laser ablation

    NASA Astrophysics Data System (ADS)

    Furzikov, Nickolay P.

    1991-09-01

    Effective temperatures of laser ablation of certain polymers are extracted from experimental dependences of ablation depths on laser fluences. Dependence of these temperatures on laser pulse durations is established. Comparison with the known thermodestruction data shows that the effective temperature corresponds to transient thermodestruction proceeding by the statistically most probable way.

  1. Mechanism study of skin tissue ablation by nanosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Fang, Qiyin

    Understanding the fundamental mechanisms in laser tissue ablation is essential to improve clinical laser applications by reducing collateral damage and laser pulse energy requirement. The motive of this dissertation is to study skin tissue ablation by nanosecond laser pulses in a wide spectral region from near-infrared to ultraviolet for a clear understanding of the mechanism that can be used to improve future design of the pulsed lasers for dermatology and plastic surgery. Multiple laser and optical configurations have been constructed to generate 9 to 12ns laser pulses with similar profiles at 1064. 532, 266 and 213nm for this study of skin tissue ablation. Through measurements of ablation depth as a function cf laser pulse energy, the 589nm spectral line in the secondary radiation from ablated skin tissue samples was identified as the signature of the occurrence of ablation. Subsequently, this spectral signature has been used to investigate the probabilistic process of the ablation near the threshold at the four wavelengths. Measurements of the ablation probability were conducted as a function of the electrical field strength of the laser pulse and the ablation thresholds in a wide spectral range from 1064nm to 213nm were determined. Histology analysis and an optical transmission method were applied in assessing of the ablation depth per pulse to study the ablation process at irradiance levels higher than threshold. Because more than 70% of the wet weight of the skin tissue is water, optical breakdown and backscattering in water was also investigated along with a nonlinear refraction index measurement using a z-scan technique. Preliminary studies on ablation of a gelatin based tissue phantom are also reported. The current theoretical models describing ablation of soft tissue ablation by short laser pulses were critically reviewed. Since none of the existing models was found capable of explaining the experimental results, a new plasma-mediated model was developed

  2. Laser tattoo removal as an ablation process monitored by acoustical and optical methods

    NASA Astrophysics Data System (ADS)

    Cencič, Boris; Gregorčič, Peter; Možina, Janez; Jezeršek, Matija

    2013-07-01

    Strength of the laser-tissue interaction varies even within a single tattoo because of the inhomogeneous distribution of the tattoo pigment embedded in the skin. A monitoring system is therefore developed for simultaneous monitoring of the laser tattoo removal process based on acoustical and optical techniques. A laser-beam-deflection probe is used for measuring the acoustical signals accompanying the breakdown, and a CCD camera captures the level and the spatial distribution of the plasma radiation. Using these methods we examine the degree of excitation-pulse absorption within the pigment and the degree of the structural changes of the skin. A Nd:YAG laser with a top-hat beam profile, designed for tattoo removal, is used as the excitation source in our experiments. Special attention is given to structural changes in the skin, which depend on the applied fluence. Tattoo removal with multiple pulses is also analyzed. Experiments are made in vitro (skin phantoms) and ex vivo (marking tattoos on the pig skin). The presented results are important for the understanding and optimization of the process used in medical therapies.

  3. UV laser ablation of parylene films from gold substrates

    SciTech Connect

    O. R. Musaev, P. Scott, J. M. Wrobel, and M. B. Kruger

    2009-11-19

    Parylene films, coating gold substrates, were removed by laser ablation using 248 nm light from an excimer laser. Each sample was processed by a different number of pulses in one of three different environments: air at atmospheric pressure, nitrogen at atmospheric pressure, and vacuum. The laser-induced craters were analyzed by optical microscopy and x-ray photoelectron spectroscopy. Multi-pulse ablation thresholds of gold and parylene were estimated.

  4. Nanosecond laser ablation for pulsed laser deposition of yttria

    NASA Astrophysics Data System (ADS)

    Sinha, Sucharita

    2013-09-01

    A thermal model to describe high-power nanosecond pulsed laser ablation of yttria (Y2O3) has been developed. This model simulates ablation of material occurring primarily through vaporization and also accounts for attenuation of the incident laser beam in the evolving vapor plume. Theoretical estimates of process features such as time evolution of target temperature distribution, melt depth and ablation rate and their dependence on laser parameters particularly for laser fluences in the range of 6 to 30 J/cm2 are investigated. Calculated maximum surface temperatures when compared with the estimated critical temperature for yttria indicate absence of explosive boiling at typical laser fluxes of 10 to 30 J/cm2. Material ejection in large fragments associated with explosive boiling of the target needs to be avoided when depositing thin films via the pulsed laser deposition (PLD) technique as it leads to coatings with high residual porosity and poor compaction restricting the protective quality of such corrosion-resistant yttria coatings. Our model calculations facilitate proper selection of laser parameters to be employed for deposition of PLD yttria corrosion-resistive coatings. Such coatings have been found to be highly effective in handling and containment of liquid uranium.

  5. Laser Navigation for Radiofrequency Ablation

    SciTech Connect

    Varro, Zoltan; Locklin, Julia K. Wood, Bradford J.

    2004-09-15

    A 45-year-old male with renal cell carcinoma secondary to von-Hippel Lindau (VHL) disease presented for radiofrequency ablation (RFA) of kidney tumors. Due to his prior history of several partial nephrectomies and limited renal reserve, RFA was chosen because of its relatively nephron-sparing nature. A laser guidance device was used to help guide probe placement in an attempt to reduce procedure time and improve targeting accuracy. The device was successful at guiding needle placement, as both tumors were located with a single pass. Follow-up CT scan confirmed accurate needle placement, showing an area of coagulation necrosis covering the previously seen tumor.

  6. Endometrial ablation

    MedlinePlus

    Hysteroscopy-endometrial ablation; Laser thermal ablation; Endometrial ablation-radiofrequency; Endometrial ablation-thermal balloon ablation; Rollerball ablation; Hydrothermal ablation; Novasure ablation

  7. Atomic Processes in Emission Characteristics of a Lithium Plasma Plume Formed by Double-Pulse Laser Ablation

    NASA Astrophysics Data System (ADS)

    Sivakumaran, V.; Ajai, Kumar; K. Singh, R.; Prahlad, V.; C. Joshi, H.

    2013-03-01

    High resolution spectral analysis of lithium plasma formed by single and double laser ablation has been undertaken to understand the plume-laser interaction, especially at the early stages of the plasma plume. In order to identify different atomic processes in evolving plasma, time resolved spectral emission studies at different inter-pulse delays have been performed for ionic and neutral lithium lines emitting from different levels. Along with the enhancement in emission intensity, a large line broadening and spectral shift, especially in the case of excited state transition Li I 610.3 nm have been observed in the presence of the second pulse. This broadening and shift gradually decrease with increasing time delay. Another interesting feature is the appearance of a multi-component structure in the ionic line at 548.4 nm and these components change conversely into a single structure at the later stages of the plasma. The multi-component structures are correlated with the presence of different velocity (temperature) distributions in non-LTE conditions. Atomic analyses by computing photon emissivity coefficients with an ADAS code have been used to identify the above processes.

  8. Influence of water environment on holmium laser ablation performance for hard tissues.

    PubMed

    Lü, Tao; Xiao, Qing; Li, Zhengjia

    2012-05-01

    This study clarifies the ablation differences in air and in water for hard biological tissues, which are irradiated by fiber-guided long-pulsed holmium lasers. High-speed photography is used to record the dynamic characteristics of ablation plumes and vaporization bubbles induced by pulsed holmium lasers. The ablation morphologies and depth of hard tissues are quantitatively measured by optical coherence microscopy. Explosive vaporization effects in water play a positive role in the contact ablation process and are directly responsible for significant ablation enhancement. Furthermore, water layer depth can also contribute to ablation performance. Under the same laser parameters for fiber-tissue contact ablation in air and water, ablation performances are comparable for a single-laser pulse, but for more laser pulses the ablation performances in water are better than those in air. Comprehensive knowledge of ablation differences under various environments is important, especially in medical procedures that are performed in a liquid environment.

  9. Laser ablation dynamics in metals: The thermal regime

    SciTech Connect

    Mezzapesa, F. P.; Brambilla, M.; Dabbicco, M.; Scamarcio, G.; Columbo, L. L.; Ancona, A.; Sibillano, T.

    2012-07-02

    We studied the laser ablation dynamics of steel in the thermal regime both experimentally and theoretically. The real-time monitoring of the process shows that the ablation rate depends on laser energy density and ambient pressure during the exposure time. We demonstrated that the ablation efficiency can be enhanced when the pressure is reduced with respect to the atmospheric pressure for a given laser fluence, reaching an upper limit despite of high-vacuum conditions. An analytical model based on the Hertz-Knudsen law reproduces all the experimental results.

  10. Ablation dynamics in laser sclerotomy ab externo

    NASA Astrophysics Data System (ADS)

    Brinkmann, Ralf; Droege, Gerit; Mohrenstecher, Dirk; Scheu, M.; Birngruber, Reginald

    1996-01-01

    Laser sclerostomy ab externo with flashlamp excited mid-IR laser systems emitting in the 2-3 micrometer spectral range is in phase II clinical trials. Although acutely high success rates were achieved, the restenosis rate after several months is about 40%. Laser pulses of several hundreds of microseconds, known to induce thermo-mechanical explosive evaporation were used for this procedure. We investigated the ablation dynamics in tissue and the cavitation bubble dynamics in water by means of an Er:YAG laser system to estimate the extent of mechanical damage zones in the sclera and in the anterior chamber, which may contribute to the clinical failure. We found substantial mechanical tissue deformation during the ablation process caused by the cavitation effects. Stress waves up to several bar generated by explosive evaporization were measured. The fast mechanical stretching and collapsing of the scleral tissue induced by cavitation resulted in tissue dissection as could be proved by flash photography and histology. The observed high restenosis might be a result of a subsequent enhanced wound healing process. Early fistula occlusions due to iris adherences, observed in about 20% of the clinical cases may be attributed to intraocular trauma induced by vapor bubble expansion through the anterior chamber after scleral perforation. An automatic feedback system minimizing adverse effects by steering and terminating the laser process during scleral fistulization is demonstrated. Moreover, a new approach in laser sclerostomy ab externo is presented using a cw-IR laser diode system emitting at the 1.94 micrometer mid-IR water absorption peak. This system was used in vitro and showed smaller damage zones compared to the pulsed laser radiation.

  11. Ablation characteristics of quantum square pulse mode dental erbium laser

    NASA Astrophysics Data System (ADS)

    Lukač, Nejc; Suhovršnik, Tomaž; Lukač, Matjaž; Jezeršek, Matija

    2016-01-01

    Erbium lasers are by now an accepted tool for performing ablative medical procedures, especially when minimal invasiveness is desired. Ideally, a minimally invasive laser cutting procedure should be fast and precise, and with minimal pain and thermal side effects. All these characteristics are significantly influenced by laser pulse duration, albeit not in the same manner. For example, high cutting efficacy and low heat deposition are characteristics of short pulses, while vibrations and ejected debris screening are less pronounced at longer pulse durations. We report on a study of ablation characteristics on dental enamel and cementum, of a chopped-pulse Er:YAG [quantum square pulse (QSP)] mode, which was designed to reduce debris screening during an ablation process. It is shown that in comparison to other studied standard Er:YAG and Er,Cr:YSGG laser pulse duration modes, the QSP mode exhibits the highest ablation drilling efficacy with lowest heat deposition and reduced vibrations, demonstrating that debris screening has a considerable influence on the ablation process. By measuring single-pulse ablation depths, we also show that tissue desiccation during the consecutive delivery of laser pulses leads to a significant reduction of the intrinsic ablation efficacy that cannot be fully restored under clinical settings by rehydrating the tooth using an external water spray.

  12. Universal threshold for femtosecond laser ablation with oblique illumination

    NASA Astrophysics Data System (ADS)

    Liu, Xiao-Long; Cheng, Weibo; Petrarca, Massimo; Polynkin, Pavel

    2016-10-01

    We quantify the dependence of the single-shot ablation threshold on the angle of incidence and polarization of a femtosecond laser beam, for three dissimilar solid-state materials: a metal, a dielectric, and a semiconductor. Using the constant, linear value of the index of refraction, we calculate the laser fluence transmitted through the air-material interface at the point of ablation threshold. We show that, in spite of the highly nonlinear ionization dynamics involved in the ablation process, the so defined transmitted threshold fluence is universally independent of the angle of incidence and polarization of the laser beam for all three material types. We suggest that angular dependence of ablation threshold can be utilized for profiling fluence distributions in ultra-intense femtosecond laser beams.

  13. IR laser ablation of dental enamel

    NASA Astrophysics Data System (ADS)

    Fried, Daniel

    2000-03-01

    An overview of the basic mechanisms of IR laser ablation of dental enamel is presented. Enamel is a highly structured tissue consisting of an heterogeneous distribution of water, mineral, protein and lipid. Absorption bands of water and carbonated hydroxyapatite can be selectively targeted from 2.7 to 11-micrometer via several laser wavelengths. Mechanistic differences in the nature of ablation and the varying surface morphology produced can be explained by the microstructure of the tissue. Suggested criteria for the choice of the optimum laser parameters for clinical use, the influence of plasma shielding and the role of exogenous water on the mechanism of ablation are discussed.

  14. Higher Order Chemistry Models in the CFD Simulation of Laser-Ablated Carbon Plumes

    NASA Technical Reports Server (NTRS)

    Greendyke, R. B.; Creel, J. R.; Payne, B. T.; Scott, C. D.

    2005-01-01

    Production of single-walled carbon nanotubes (SWNT) has taken place for a number of years and by a variety of methods such as laser ablation, chemical vapor deposition, and arc-jet ablation. Yet, little is actually understood about the exact chemical kinetics and processes that occur in SWNT formation. In recent time, NASA Johnson Space Center has devoted a considerable effort to the experimental evaluation of the laser ablation production process for SWNT originally developed at Rice University. To fully understand the nature of the laser ablation process it is necessary to understand the development of the carbon plume dynamics within the laser ablation oven. The present work is a continuation of previous studies into the efforts to model plume dynamics using computational fluid dynamics (CFD). The ultimate goal of the work is to improve understanding of the laser ablation process, and through that improved understanding, refine the laser ablation production of SWNT.

  15. Modeling of multi-burst mode pico-second laser ablation for improved material removal rate

    NASA Astrophysics Data System (ADS)

    Hu, Wenqian; Shin, Yung C.; King, Galen

    2010-02-01

    This paper deals with the unique phenomena occurring during the multi-burst mode picosecond (ps) laser ablation of metals through modeling and experimental studies. The two-temperature model (TTM) is used and expanded to calculate the ablation depth in the multi-burst mode. A nonlinear increment of ablation volume is found during the multi-burst laser ablation. The deactivation of ablated material and the application of temperature-dependent electron-phonon coupling are demonstrated to be important to provide reliable results. The simulation results based on this expanded laser ablation model are experimentally validated. A significant increase of ablation rate is found in the multi-burst mode, compared with the single-pulse mode under the same total fluence. This numerical model provides a physical perspective into the energy transport process during multi-burst laser ablation and can be used to study the pulse-to-pulse separation time effect on the ablation rate.

  16. In situ iron isotope ratio determination using UV-femtosecond laser ablation with application to hydrothermal ore formation processes

    NASA Astrophysics Data System (ADS)

    Horn, Ingo; von Blanckenburg, Friedhelm; Schoenberg, Ronny; Steinhoefel, Grit; Markl, Gregor

    2006-07-01

    The feasibility of in situ stable Fe isotope ratio measurements using UV-femtosecond laser ablation connected to a multiple-collector inductively coupled plasma mass spectrometer (MC-ICP-MS) has been investigated. Different types of matrices, independently determined by solution MC-ICP-MS after chromatographic separation of Fe, have been analysed by laser ablation using the isotopically certified iron reference material IRMM-014 as the bracketing standard. The samples have been pure iron metal (JM Puratronic), Fe-meteorites (North Chile, Glenormiston and Toluca), the meteorite phases kamacite and taenite in Toluca and Fe-sulphides. Furthermore, Fe isotope ratios from hydrothermal hematite, siderite and goethite from an old mining area in the Schwarzwald, Germany, and of magnetite from the metamorphic Biwabik iron formation have been determined. The results show that a precision of better than 0.1‰ (2 sigma) can be achieved with laser ablation and that all the results obtained agree with those determined by solution ICP to better than 0.1‰. This precision and accuracy is achievable in both raster and spot ablation mode. A matrix-matched bracketing standard is not required , and all these materials can be measured accurately against a metal standard. The hydrothermal minerals show significant Fe isotope zonations. In some samples the range of δ56Fe in a single aggregate encompasses the entire spectrum of ratios found by bulk solution analyses in multiple samples distributed over the whole mining district. For example, isotopic zonations found in secondary fibrous hematites show a continuous change in the δ56Fe values from -0.5‰ in the core to -1.8‰ in the rim. Primary hydrothermal siderite shows the reverse pattern with lighter values in the core than in the rim. While the siderite is thought to record primary fluid histories, the hematite pattern is interpreted as a reworked isotopic signature generated by oxic dissolution of primary zoned siderite and

  17. Nanosecond laser ablation of gold nanoparticle films

    SciTech Connect

    Ko, Seung H.; Choi, Yeonho; Hwang, David J.; Grigoropoulos, Costas P.; Chung, Jaewon; Poulikakos, Dimos

    2006-10-02

    Ablation of self-assembled monolayer protected gold nanoparticle films on polyimide was explored using a nanosecond laser. When the nanoparticle film was ablated and subsequently thermally sintered to a continuous film, the elevated rim structure by the expulsion of molten pool could be avoided and the ablation threshold fluence was reduced to a value at least ten times lower than the reported threshold for the gold film. This could be explained by the unusual properties of nanoparticle film such as low melting temperature, weak bonding between nanoparticles, efficient laser energy deposition, and reduced heat loss. Finally, submicron lines were demonstrated.

  18. Effects of Laser Wavelength on Ablator Testing

    NASA Technical Reports Server (NTRS)

    White, Susan M.

    2014-01-01

    Wavelength-dependent or spectral radiation effects are potentially significant for thermal protection materials. NASA atmospheric entry simulations include trajectories with significant levels of shock layer radiation which is concentrated in narrow spectral lines. Tests using two different high powered lasers, the 10.6 micron LHMEL I CO2 laser and the near-infrared 1.07 micron fiber laser, on low density ablative thermal protection materials offer a unique opportunity to evaluate spectral effects. Test results indicated that the laser wavelength can impact the thermal response of an ablative material, in terms of bond-line temperatures, penetration times, mass losses, and char layer thicknesses.

  19. Analysis of infrared laser tissue ablation

    NASA Astrophysics Data System (ADS)

    McKenzie, Gordon P.; Timmerman, Brenda H.; Bryanston-Cross, Peter J.

    2005-04-01

    The mechanisms involved in infrared laser tissue ablation are studied using a free electron laser (FELIX) in order to clarify whether the increased ablation efficiency reported in literature for certain infrared wavelengths is due to a wavelength effect or to the specific pulse structure of the lasers that are generally used in these studies. Investigations are presented of ablation of vitreous from pigs" eyes using several techniques including protein gel electrophoresis and ablation plume visualization. The ablation effects of three different infrared wavelengths are compared: 3 mm, which is currently in clinical surgical use, and the wavelengths associated with the amide I and amide II bands, i.e. 6.2 mm and 6.45mm, respectively. The results suggest a different ablation mechanism to be in operation for each studied wavelength, thus indicating that the generally reported increased ablation efficiency in the 6-6.5 micron range is due to the wavelength rather than the typical free electron laser pulse structure.

  20. Femtosecond laser ablation of polytetrafluoroethylene (Teflon) in ambient air

    NASA Astrophysics Data System (ADS)

    Wang, Z. B.; Hong, M. H.; Lu, Y. F.; Wu, D. J.; Lan, B.; Chong, T. C.

    2003-05-01

    Teflon, polytetrafluorethylene (PTFE), is an important material in bioscience and medical application due to its special characteristics (bio-compatible, nonflammable, antiadhesive, and heat resistant). The advantages of ultrashort laser processing of Teflon include a minimal thermal penetration region and low processing temperatures, precision removal of material, and good-quality feature definition. In this paper, laser processing of PTFE in ambient air by a Ti:sapphire femtosecond laser (780 nm, 110 fs) is investigated. It is found that the pulse number on each irradiated surface area must be large enough for a clear edge definition and the ablated depth increases with the pulse number. The air ionization effect at high laser fluences not only degrades the ablated structures quality but also reduces the ablation efficiency. High quality microstructures are demonstrated with controlling laser fluence below a critical fluence to exclude the air ionization effect. The ablated microstructures show strong adhesion property to liquids and clear edges that are suitable for bio-implantation applications. Theoretical calculation is used to analyze the evolution of the ablated width and depth at various laser fluences.

  1. Activation processes and polyethylene formation on a phillips model catalyst studied by laser ablation, laser desorption, and static secondary ion mass spectrometry.

    PubMed

    Aubriet, Frédéric; Muller, Jean-François; Poleunis, Claude; Bertrand, Patrick; Di Croce, Pascal G; Grange, Paul

    2006-03-01

    Since the discovery of the Phillips catalysts, there still is much uncertainty concerning their activation, their molecular structure, the nature of the active chromium sites, and the polymerization mechanisms. Surface techniques are not easy to be used for such study according to the nonconductive behavior of the support. Therefore, model Phillips catalyst is elaborated by spin coating a trivalent chromium precursor on a silicon wafer. The surface characterization of this model catalyst is conducted by laser ablation mass spectrometry (LA-MS), laser desorption/ionization mass spectrometry (LDI-MS), and static secondary ion mass spectrometry (s-SIMS), at different steps of its preparation. To validate our approach, a comparison is also made between the model and the real Philips catalyst. Moreover, the model catalyst efficiency for polyethylene synthesis is evaluated and allows us to discuss the validity of the mechanisms previously proposed to explain the catalytic process. The characterization of Phillips model catalyst by mass spectrometry allows us to better understand the activation processes of such catalyst. Depending on the activation temperature, chromium oxide species are formed and anchored at the support surface. They consist mainly in mono-chromium sites at high temperature. The chromium valence is hexavalent. This model catalyst is active for the polymerization of ethylene. A pseudo-oligomer molecular weight distribution is observed by LA-MS, whereas s-SIMS allows us to elucidate the anchorage of the polymer at activate chromium surface sites.

  2. Femtosecond laser bone ablation with a high repetition rate fiber laser source.

    PubMed

    Mortensen, Luke J; Alt, Clemens; Turcotte, Raphaël; Masek, Marissa; Liu, Tzu-Ming; Côté, Daniel C; Xu, Chris; Intini, Giuseppe; Lin, Charles P

    2015-01-01

    Femtosecond laser pulses can be used to perform very precise cutting of material, including biological samples from subcellular organelles to large areas of bone, through plasma-mediated ablation. The use of a kilohertz regenerative amplifier is usually needed to obtain the pulse energy required for ablation. This work investigates a 5 megahertz compact fiber laser for near-video rate imaging and ablation in bone. After optimization of ablation efficiency and reduction in autofluorescence, the system is demonstrated for the in vivo study of bone regeneration. Image-guided creation of a bone defect and longitudinal evaluation of cellular injury response in the defect provides insight into the bone regeneration process.

  3. Pulsed HF laser ablation of dentin

    NASA Astrophysics Data System (ADS)

    Papagiakoumou, Eirini I.; Papadopoulos, Dimitris N.; Makropoulou, Mersini I.; Khabbaz, Maruan G.; Serafetinides, Alexander A.

    2005-03-01

    The interaction of a TEA (Transversally Excited Atmospheric pressure) corona preionized oscillator double amplifier HF (hydrogen fluoride) laser beam with dentin tissue is reported. Pulses of 39 ns in the wavelength range of 2.65-3.35 μm and output energies in the range of 10-45 mJ, in a predominantly TEM00 beam were used to interact with dentin tissue. Ablation experiments were conducted with the laser beam directly focused on the tissue. Several samples of freshly extracted human teeth were used, cut longitudinally in facets of about 1mm thick and stored in phosphate buffered saline after being cleaned from the soft tissue remains. The experimental data (ablation thresholds, ablation rates) are discussed with respect to the ablation mechanism(s). Adequate tissue removal was observed and the ablation behavior was, in the greates part of the available fluences, almost linear. From the microscopic examination of teh samples, in a scanning electron microscope (SEM), the irradiated surfaces displayed oval craters (reflecting the laser beam shape) with absence of any melting or carbonization zone. It is suggested that the specific laser removes hard tissue by a combined photothermal and plasma mediated ablation mechanism, leaving a surface free from thermal damage and with a well-shaped crater.

  4. A comparison of the characteristics of excimer and femtosecond laser ablation of acrylonitrile butadiene styrene (ABS)

    NASA Astrophysics Data System (ADS)

    See, Tian Long; Liu, Zhu; Li, Lin; Zhong, Xiang Li

    2016-02-01

    This paper presents an investigation on the ablation characteristics of excimer laser (λ = 248 nm, τ = 15 ns) and femtosecond laser (λ = 800 nm, τ = 100 fs) on ABS polymer sheets. The laser-material interaction parameters (ablation threshold, optical penetration depth and incubation factor) and the changes in material chemical properties were evaluated and compared between the two lasers. The work shows that the ablation threshold and effective optical penetration depth values are dependent on the wavelength of laser beam (photon energy) and the pulse width. The ablation threshold value is lower for the excimer laser ablation of ABS (Fth = 0.087 J/cm2) than that for the femtosecond laser ablation of ABS (Fth = 1.576 J/cm2), demonstrating a more dominating role of laser wavelength than the pulse width in influencing the ablation threshold. The ablation depth versus the logarithmic scale of laser fluence shows two linear regions for the fs laser ablation, not previously known for polymers. The effective optical penetration depth value is lower for excimer laser ablation (α-1 = 223 nm) than that for femtosecond laser ablation (α-1 = 2917 nm). The ablation threshold decreases with increasing number of pulses (NOP) due to the chain scission process that shortens the polymeric chains, resulting in a weaker polymeric configuration and the dependency is governed by the incubation factor. Excimer laser treatment of ABS eliminates the Cdbnd C bond completely through the chain scission process whereas Cdbnd C bond is partially eliminated through the femtosecond laser treatment due to the difference in photon energy of the two laser beams. A reduction in the Cdbnd C bond through the chain scission process creates free radical carbons which then form crosslinks with each other or react with oxygen, nitrogen and water in air producing oxygen-rich (Csbnd O and Cdbnd O bond) and nitrogen-rich (Csbnd N) functional groups.

  5. Heat effects of metals ablated with femtosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Hirayama, Yoichi; Obara, Minoru

    2002-09-01

    Heat effects of metallic bulk crystals of Au, Ag, Cu, and Fe ablated with femtosecond Ti:sapphire laser pulses is experimentally studied. As a result of X-ray diffraction (XRD) measurements, the XRD peak signal of the area ablated with Ti:sapphire laser is much smaller than that of the crystalline metal sample. While the crystal form of the metal sample is crystalline before laser ablation, the crystal form in the ablated area is partially changed into the amorphous form. The residual pulse energy that did not contribute to the ablation process remains, which leads to the formation of thin layer of melted phase. The melted layer is abruptly cooled down not to be re-crystallized, but to transform into amorphous form. It is evident that the area ablated with femtosecond laser is changed into amorphous metals. This mechanism would be the same as the melt-quenching generally used as the fabrication method of amorphous metals. This experimental result is consistent with the theoretical result.

  6. Visual servoing of a laser ablation based cochleostomy

    NASA Astrophysics Data System (ADS)

    Kahrs, Lüder A.; Raczkowsky, Jörg; Werner, Martin; Knapp, Felix B.; Mehrwald, Markus; Hering, Peter; Schipper, Jörg; Klenzner, Thomas; Wörn, Heinz

    2008-03-01

    The aim of this study is a defined, visually based and camera controlled bone removal by a navigated CO II laser on the promontory of the inner ear. A precise and minimally traumatic opening procedure of the cochlea for the implantation of a cochlear implant electrode (so-called cochleostomy) is intended. Harming the membrane linings of the inner ear can result in damage of remaining organ functions (e.g. complete deafness or vertigo). A precise tissue removal by a laser-based bone ablation system is investigated. Inside the borehole the pulsed laser beam is guided automatically over the bone by using a two mirror galvanometric scanner. The ablation process is controlled by visual servoing. For the detection of the boundary layers of the inner ear the ablation area is monitored by a color camera. The acquired pictures are analyzed by image processing. The results of this analysis are used to control the process of laser ablation. This publication describes the complete system including image processing algorithms and the concept for the resulting distribution of single laser pulses. The system has been tested on human cochleae in ex-vivo studies. Further developments could lead to safe intraoperative openings of the cochlea by a robot based surgical laser instrument.

  7. Laser ablation of polymeric materials at 157 nm

    NASA Astrophysics Data System (ADS)

    Costela, A.; García-Moreno, I.; Florido, F.; Figuera, J. M.; Sastre, R.; Hooker, S. M.; Cashmore, J. S.; Webb, C. E.

    1995-03-01

    Results are presented on the ablation by 157 nm laser radiation of polytetrafluoroethylene (PTFE), polyimide, polyhydroxybutyrate (PHB), poly(methyl methacrylate) (PMMA), and poly(2-hydroxyethyl methacrylate) with 1% of ethylene glycol dimethacrylate as a crosslinking monomer. Direct photoetching of PHB and undoped PTFE is demonstrated for laser fluences ranging from 0.05 to 0.8 J/cm2. The dependence of the ablation process on the polymer structure is analyzed, and insight into the ablation mechanism is gained from an analysis of the data using Beer-Lambert's law and the kinetic model of the moving interface. Consideration of the absorbed energy density required to initiate significant ablation suggests that the photoetching mechanism is similar for all the polymers studied.

  8. UV laser ablation patterns in intraocular lenses

    NASA Astrophysics Data System (ADS)

    Lagiou, D. P.; Evangelatos, Ch.; Apostolopoulos, A.; Spyratou, E.; Bacharis, C.; Makropoulou, M.; Serafetinides, A. A.

    2013-03-01

    The aim of this work is to investigate the effect of UV solid state laser radiation on intraocular lens (IOL) polymer surfaces as an alternative method to conventional surface shaping techniques for IOLs customization. Laser ablation experiments were performed on PMMA plates and commercially available hydrophobic and hydrophilic acrylic IOLs with the 5th harmonic of a Q-switched Nd:YAG laser (λ=213 nm). Circular arrays of holes were drilled on the polymer surface, covering the centre and the peripheries of the IOL. The morphology of the ablated IOL surface was examined with a conventional optical microscope (Leitz GMBH Wetzlar) and with a scanning electron microscope (SEM, Fei - Innova Nanoscope) at various laser parameters. Quantitative measurements of ablation rates were performed with a contact profilometer (Dektak-150), in which a mechanical stylus scanned across the surface of gold-coated IOLs (after SEM imaging) to measure variationsF in surface height. Laser interaction with IOLs depends on optical and mechanical material properties, in addition to laser radiation parameters. The exact ablation mechanism is discussed. Some polymer materials, depending on their properties, are more susceptible to the photothermal mechanism than the photochemical one or vice versa. In summary, every IOL polymer exhibits specific attributes in its interaction with the 5th harmonic of Nd:YAG laser.

  9. Resonant laser ablation: mechanisms and applications

    SciTech Connect

    Anderson, J.E.; Allen, T.M.; Garrett, A.W.; Gill, C.G.; Hemberger, P.H.; Kelly, P.B.; Nogar, N.S.

    1996-10-01

    We report on aspects of resonant laser ablation (RLA) behavior for a number of sample types: metals, alloys, thin films, zeolites and soil. The versatility of RLA is demonstrated, with results on a variety of samples and in several mass spectrometers. In addition, the application to depth profiling of thin films is described; absolute removal rates and detection limits are also displayed. A discussion of possible mechanisms for low-power ablation is presented.

  10. Laser ablated hard coating for microtools

    DOEpatents

    McLean, W. II; Balooch, M.; Siekhaus, W.J.

    1998-05-05

    Wear-resistant coatings composed of laser ablated hard carbon films, are deposited by pulsed laser ablation using visible light, on instruments such as microscope tips and micro-surgical tools. Hard carbon, known as diamond-like carbon (DLC), films produced by pulsed laser ablation using visible light enhances the abrasion resistance, wear characteristics, and lifetimes of small tools or instruments, such as small, sharp silicon tips used in atomic probe microscopy without significantly affecting the sharpness or size of these devices. For example, a 10--20 nm layer of diamond-like carbon on a standard silicon atomic force microscope (AFM) tip, enables the useful operating life of the tip to be increased by at least twofold. Moreover, the low inherent friction coefficient of the DLC coating leads to higher resolution for AFM tips operating in the contact mode. 12 figs.

  11. Laser ablated hard coating for microtools

    DOEpatents

    McLean, II, William; Balooch, Mehdi; Siekhaus, Wigbert J.

    1998-05-05

    Wear-resistant coatings composed of laser ablated hard carbon films, are deposited by pulsed laser ablation using visible light, on instruments such as microscope tips and micro-surgical tools. Hard carbon, known as diamond-like carbon (DLC), films produced by pulsed laser ablation using visible light enhances the abrasion resistance, wear characteristics, and lifetimes of small tools or instruments, such as small, sharp silicon tips used in atomic probe microscopy without significantly affecting the sharpness or size of these devices. For example, a 10-20 nm layer of diamond-like carbon on a standard silicon atomic force microscope (AFM) tip, enables the useful operating life of the tip to be increased by at least twofold. Moreover, the low inherent friction coefficient of the DLC coating leads to higher resolution for AFM tips operating in the contact mode.

  12. Emission spectroscopy analysis during Nopal cladodes dethorning by laser ablation

    NASA Astrophysics Data System (ADS)

    Peña-Díaz, M.; Ponce, L.; Arronte, M.; Flores, T.

    2007-04-01

    Optical emission spectroscopy of the pulsed laser ablation of spines and glochids from Opuntia (Nopal) cladodes was performed. Nopal cladodes were irradiated with Nd:YAG free-running laser pulses on their body, glochids and spines. Emission spectroscopy analyses in the 350-1000 nm region of the laser induced plasma were made. Plasma plume evolution characterization, theoretical calculations of plasma plume temperature and experiments varying the processing atmosphere showed that the process is dominated by a thermally activated combustion reaction which increases the dethorning process efficiency. Therefore, appropriate laser pulse energy for minimal damage of cladodes body and in the area beneath glochids and spines can be obtained.

  13. Cartilage ablation studies using mid-IR free electron laser

    NASA Astrophysics Data System (ADS)

    Youn, Jong-In; Peavy, George M.; Venugopalan, Vasan

    2005-04-01

    The ablation rate of articular cartilage and fibrocartilage (meniscus), were quantified to examine wavelength and tissue-composition dependence of ablation efficiency for selected mid-infrared wavelengths. The wavelengths tested were 2.9 um (water dominant absorption), 6.1 (protein and water absorption) and 6.45 um (protein dominant absorption) generated by the Free Electron Laser (FEL) at Vanderbilt University. The measurement of tissue mass removal using a microbalance during laser ablation was conducted to determine the ablation rates of cartilage. The technique can be accurate over methods such as profilometer and histology sectioning where tissue surface and the crater morphology may be affected by tissue processing. The ablation efficiency was found to be dependent upon the wavelength. Both articular cartilage and meniscus (fibrocartilage) ablations at 6.1 um were more efficient than those at the other wavelengths evaluated. We observed the lowest ablation efficiency of both types of cartilage with the 6.45 um wavelength, possibly due to the reduction in water absorption at this wavelength in comparison to the other wavelengths that were evaluated.

  14. Ablative Laser Propulsion Using Multi-Layered Material Systems

    NASA Technical Reports Server (NTRS)

    Nehls, Mary; Edwards, David; Gray, Perry; Schneider, T.

    2002-01-01

    Experimental investigations are ongoing to study the force imparted to materials when subjected to laser ablation. When a laser pulse of sufficient energy density impacts a material, a small amount of the material is ablated. A torsion balance is used to measure the momentum produced by the ablation process. The balance consists of a thin metal wire with a rotating pendulum suspended in the middle. The wire is fixed at both ends. Recently, multi-layered material systems were investigated. These multi-layered materials were composed of a transparent front surface and opaque sub surface. The laser pulse penetrates the transparent outer surface with minimum photon loss and vaporizes the underlying opaque layer.

  15. Nanoscale patterning of graphene through femtosecond laser ablation

    SciTech Connect

    Sahin, R.; Akturk, S.; Simsek, E.

    2014-02-03

    We report on nanometer-scale patterning of single layer graphene on SiO{sub 2}/Si substrate through femtosecond laser ablation. The pulse fluence is adjusted around the single-pulse ablation threshold of graphene. It is shown that, even though both SiO{sub 2} and Si have more absorption in the linear regime compared to graphene, the substrate can be kept intact during the process. This is achieved by scanning the sample under laser illumination at speeds yielding a few numbers of overlapping pulses at a certain point, thereby effectively shielding the substrate. By adjusting laser fluence and translation speed, 400 nm wide ablation channels could be achieved over 100 μm length. Raster scanning of the sample yields well-ordered periodic structures, provided that sufficient gap is left between channels. Nanoscale patterning of graphene without substrate damage is verified with Scanning Electron Microscope and Raman studies.

  16. Dynamics of multiple plumes in laser ablation: Modeling of the shielding effect

    NASA Astrophysics Data System (ADS)

    Zinovik, Igor; Povitsky, Alex

    2006-07-01

    The scattering and absorption of laser radiation by previously ablated plumes in laser ablation (known as the shielding effect) dramatically affect the efficiency of laser ablation process. The ablated plumes consisting of water vapor, droplets, and particles are modeled as a gas-particle equilibrium mixture by solution of the Euler equations combined with the transport equation for the ratio of heat capacities. Shielding effect on the overall ablated mass by multiple plumes is studied for a wide range of concentration of particles in vaporized plumes, various laser repetition rates, scattering, and absorption of laser energy. The shielding phenomenon is studied for short sequences of discrete plumes to focus on the shielding effect of individual plumes. The results of numerical modeling were compared to experimental results of laser-induced water explosive vaporization. Ablation rate was calculated for a single ablated plume and for the sequence of six laser pulses at the repetition rates of 0.33 and 1MHz at which gas dynamics interactions between plumes are strong but plumes have not yet form a continuous jet. A single ablated plume has an initial semispherical shape which transforms into mushroomlike cloud with a thin stem and a ring vortex as it was observed in experiments with water and cornea ablation. For the plume with a given ablated mass, the longer ejection of plume with smaller density produces the plume with smaller shielding capacity. For multiple laser pulses, the velocity of ejected mixture increases from the center of the target to its periphery because of the shielding effect. The ablated mass of the current plume depends on the attenuation of the incident laser beam energy caused by the propagation of laser beam through previously ablated plumes. In the case of laser energy absorption, the ablation rate per pulse exceeds 2-2.5 times the rate obtained for the laser energy scattering.

  17. Outpatient laser tonsillar ablation under local anaesthetic.

    PubMed

    Andrews, Peter J; Latif, Abdul

    2004-11-01

    Outpatient laser ablation of the palatine tonsils under local anaesthetic is an alternative technique to capsular tonsillectomy for recurrent tonsillitis under general anaesthetic. Laser tonsillotomy ablates up to 70% of the tonsillar tissue and is performed when patients choose not to have a conventional tonsillectomy, or are unfit for a general anaesthetic. The technique described here is an adaptation of Krespis' laser-assisted serial tonsillectomy (LAST) whereby only one sitting is required. Krespis' technique effectively eliminates recurrent tonsillitis in 96% of the cases over a 4-year follow-up period and represents the only substantial study looking at treating recurrent tonsillitis with outpatient laser ablation. This study is a retrospective postal survey of 19 patients who underwent laser tonsillar ablation under local anaesthetic for recurrent chronic tonsillitis from 1997 to 2001 and was performed in liaison with the clinical audit department at Basildon Hospital. We had a response rate of 74% and an admission rate of 0%, which compares favourably with day case tonsillectomy surgery. Of the patients, 75% did not experience further episodes of tonsillitis 12 months after the procedure and 77% of the patients were glad they had the operation. Although this technique does not completely eliminate tonsillitis, it offers an alternative for those patients who prefer a procedure that is done quickly in an outpatient setting without the additional problems of general anaesthesia, overnight hospital admission and long waiting lists.

  18. Laser ablation of GaAs in liquid: the role of laser pulse duration

    NASA Astrophysics Data System (ADS)

    De Bonis, Angela; Galasso, Agostino; Santagata, Antonio; Teghil, Roberto

    2016-01-01

    The synthesis of gallium arsenide (GaAs) nanoparticles has attracted wide scientific and technological interest due to the possibility of tuning the GaAs NP (nanoparticle) band gap across the visible spectrum and their consequent use in optoelectronic devices. In recent years, laser ablation in liquid (LAL) has been widely used for the preparation of colloidal solutions of semiconducting and metallic nanoparticles, thanks to its flexibility. With the aim of highlighting the key role played by laser pulse duration on the ablation mechanism and on the properties of the obtained materials, laser ablation of a gallium arsenide target in acetone was performed using laser sources operating in two different temporal regimes: Nd:glass laser (λ   =  527 nm, pulse duration of 250 fs and frequency repetition rate of 10 Hz) and Nd:YAG laser (λ   =  532 nm, pulse duration of 7 ns and frequency repetition rate of 10 Hz). The ablation process was studied following the dynamics of the laser induced shock waves (SWs) and cavitation bubbles (CBs) by fast shadowgraphy, showing that CB dimension and lifetime is related to the laser pulse length. A characterization of the obtained materials by TEM (transmission electron microscopy) and microRaman spectroscopy have shown that quite spherical gallium oxide/GaAs nanoparticles can be obtained by nanosecond laser ablation. On the other hand, pure polycrystalline GaAs nanoparticles can be produced by using an ultrashort laser source.

  19. Laser Thermal Ablation of Thyroid Benign Nodules

    PubMed Central

    Shahrzad, Mohammad Karim

    2015-01-01

    Thermal ablation therapies for benign thyroid nodules have been introduced in recent years to avoid the complications of traditional methods such as surgery. Despite the little complications and the reportedly acceptable efficacy of thermal ablation methods, quite few medical centers have sought the potential benefits of employing them. This paper provides an introduction to the literature, principles and advances of Percutaneous Laser Ablation therapy of thyroid benign nodules, as well as a discussion on its efficacy, complications and future. Several clinical research papers evaluating the thermal effect of laser on the alleviation of thyroid nodules have been reviewed to illuminate the important points. The results of this research can help researchers to advance the approach and medical centers to decide on investing in these novel therapies. PMID:26705459

  20. Excimer laser ablation of the cornea

    NASA Astrophysics Data System (ADS)

    Pettit, George H.; Ediger, Marwood N.; Weiblinger, Richard P.

    1995-03-01

    Pulsed ultraviolet laser ablation is being extensively investigated clinically to reshape the optical surface of the eye and correct vision defects. Current knowledge of the laser/tissue interaction and the present state of the clinical evaluation are reviewed. In addition, the principal findings of internal Food and Drug Administration research are described in some detail, including a risk assessment of the laser-induced-fluorescence and measurement of the nonlinear optical properties of cornea during the intense UV irradiation. Finally, a survey is presented of the alternative laser technologies being explored for this ophthalmic application.

  1. Numerical analysis of laser ablation and damage in glass with multiple picosecond laser pulses.

    PubMed

    Sun, Mingying; Eppelt, Urs; Russ, Simone; Hartmann, Claudia; Siebert, Christof; Zhu, Jianqiang; Schulz, Wolfgang

    2013-04-08

    This study presents a novel numerical model for laser ablation and laser damage in glass including beam propagation and nonlinear absorption of multiple incident ultrashort laser pulses. The laser ablation and damage in the glass cutting process with a picosecond pulsed laser was studied. The numerical results were in good agreement with our experimental observations, thereby revealing the damage mechanism induced by laser ablation. Beam propagation effects such as interference, diffraction and refraction, play a major role in the evolution of the crater structure and the damage region. There are three different damage regions, a thin layer and two different kinds of spikes. Moreover, the electronic damage mechanism was verified and distinguished from heat modification using the experimental results with different pulse spatial overlaps.

  2. Thermal melting and ablation of silicon by femtosecond laser radiation

    SciTech Connect

    Ionin, A. A.; Kudryashov, S. I. Seleznev, L. V.; Sinitsyn, D. V.; Bunkin, A. F.; Lednev, V. N.; Pershin, S. M.

    2013-03-15

    The space-time dynamics of thermal melting, subsurface cavitation, spallative ablation, and fragmentation ablation of the silicon surface excited by single IR femtosecond laser pulses is studied by timeresolved optical reflection microscopy. This dynamics is revealed by monitoring picosecond and (sub)nanosecond oscillations of probe pulse reflection, which is modulated by picosecond acoustic reverberations in the dynamically growing surface melt subjected to ablation and having another acoustic impedance, and by optical interference between the probe pulse replicas reflected by the spalled layer surface and the layer retained on the target surface. The acoustic reverberation periods change during the growth and ablation of the surface melt film, which makes it possible to quantitatively estimate the contributions of these processes to the thermal dynamics of the material surface. The results on the thermal dynamics of laser excitation are supported by dynamic measurements of the ablation parameters using noncontact ultrasonic diagnostics, scanning electron microscopy, atomic force microscopy, and optical interference microscopy of the modified regions appearing on the silicon surface after ablation.

  3. A Review of Laser Ablation Propulsion

    NASA Astrophysics Data System (ADS)

    Phipps, Claude; Bohn, Willy; Lippert, Thomas; Sasoh, Akihiro; Schall, Wolfgang; Sinko, John

    2010-10-01

    Laser Ablation Propulsion is a broad field with a wide range of applications. We review the 30-year history of laser ablation propulsion from the transition from earlier pure photon propulsion concepts of Oberth and Sänger through Kantrowitz's original laser ablation propulsion idea to the development of air-breathing "Lightcraft" and advanced spacecraft propulsion engines. The polymers POM and GAP have played an important rôle in experiments and liquid ablation fuels show great promise. Some applications use a laser system which is distant from the propelled object, for example, on another spacecraft, the Earth or a planet. Others use a laser that is part of the spacecraft propulsion system on the spacecraft. Propulsion is produced when an intense laser beam strikes a condensed matter surface and produces a vapor or plasma jet. The advantages of this idea are that exhaust velocity of the propulsion engine covers a broader range than is available from chemistry, that it can be varied to meet the instantaneous demands of the particular mission, and that practical realizations give lower mass and greater simplicity for a payload delivery system. We review the underlying theory, buttressed by extensive experimental data. The primary problem in laser space propulsion theory has been the absence of a way to predict thrust and specific impulse over the transition from the vapor to the plasma regimes. We briefly discuss a method for combining two new vapor regime treatments with plasma regime theory, giving a smooth transition from one regime to the other. We conclude with a section on future directions.

  4. A Review of Laser Ablation Propulsion

    SciTech Connect

    Phipps, Claude; Bohn, Willy; Lippert, Thomas; Sasoh, Akihiro; Schall, Wolfgang; Sinko, John

    2010-10-08

    Laser Ablation Propulsion is a broad field with a wide range of applications. We review the 30-year history of laser ablation propulsion from the transition from earlier pure photon propulsion concepts of Oberth and Saenger through Kantrowitz's original laser ablation propulsion idea to the development of air-breathing 'Lightcraft' and advanced spacecraft propulsion engines. The polymers POM and GAP have played an important role in experiments and liquid ablation fuels show great promise. Some applications use a laser system which is distant from the propelled object, for example, on another spacecraft, the Earth or a planet. Others use a laser that is part of the spacecraft propulsion system on the spacecraft. Propulsion is produced when an intense laser beam strikes a condensed matter surface and produces a vapor or plasma jet. The advantages of this idea are that exhaust velocity of the propulsion engine covers a broader range than is available from chemistry, that it can be varied to meet the instantaneous demands of the particular mission, and that practical realizations give lower mass and greater simplicity for a payload delivery system. We review the underlying theory, buttressed by extensive experimental data. The primary problem in laser space propulsion theory has been the absence of a way to predict thrust and specific impulse over the transition from the vapor to the plasma regimes. We briefly discuss a method for combining two new vapor regime treatments with plasma regime theory, giving a smooth transition from one regime to the other. We conclude with a section on future directions.

  5. Temperature dependent ablation threshold in silicon using ultrashort laser pulses

    NASA Astrophysics Data System (ADS)

    Thorstensen, Jostein; Erik Foss, Sean

    2012-11-01

    We have experimentally investigated the ablation threshold in silicon as a function of temperature when applying ultrashort laser pulses at three wavelengths. By varying the temperature of a silicon substrate from room temperature to 320 °C, we observe that the ablation threshold for a 3 ps pulse using a wavelength of 1030 nm drops from 0.43 J/cm2 to 0.24 J/cm2, a reduction of 43%. For a wavelength of 515 nm, the ablation threshold drops from 0.22 J/cm2 to 0.15 J/cm2, a reduction of 35%. The observed ablation threshold for pulses at 343 nm remains constant with temperature, at 0.10 J/cm2. These results indicate that substrate heating is a useful technique for lowering the ablation threshold in industrial silicon processing using ultrashort laser pulses in the IR or visible wavelength range. In order to investigate and explain the observed trends, we apply the two-temperature model, a thermodynamic model for investigation of the interaction between silicon and ultrashort laser pulses. Applying the two-temperature model implies thermal equilibrium between optical and acoustic phonons. On the time scales encountered herein, this need not be the case. However, as discussed in the article, the two-temperature model provides valuable insight into the physical processes governing the interaction between the laser light and the silicon. The simulations indicate that ablation occurs when the number density of excited electrons reaches the critical electron density, while the lattice remains well below vaporization temperature. The simulated laser fluence required to reach critical electron density is also found to be temperature dependent. The dominant contributor to increased electron density is, in the majority of the investigated cases, the linear absorption coefficient. Two-photon absorption and impact ionization also generate carriers, but to a lesser extent. As the linear absorption coefficient is temperature dependent, we find that the simulated reduction in

  6. Laser wavelength effect on nanosecond laser light reflection in ablation of metals

    NASA Astrophysics Data System (ADS)

    Benavides, O.; de la Cruz May, L.; Mejia, E. B.; Ruz Hernandez, J. A.; Flores Gil, A.

    2016-12-01

    Reflection of nanosecond laser pulses with different wavelengths (1.06 and 0.69 µm) in ablation of titanium in air is studied experimentally. The laser wavelength effect on reflection is essential at low laser fluence values. However, it becomes negligible for laser fluence values by about an order of magnitude higher than the plasma ignition threshold. We speculate that the disappearance of the wavelength effect is explained by counter-acting processes of the laser light absorption in plasma, which increases with laser wavelength, and absorption in the surface layer, which decreases with increasing laser wavelength.

  7. Mathematical Modeling of Laser Ablation in Liquids with Applications to Laser Ultrasonics

    SciTech Connect

    Conant, R. J.; Telschow, Kenneth Louis; Walter, John Bradley

    2002-12-01

    The use of laser ablation as a means of generating ultrasonic waves in liquid metals is studied in this paper. A mathematical model for predicting the onset of ablation is developed, as is a model of the ablation process based on steady state, one-dimensional gas dynamics in which the vapor phase is treated as an ideal gas. The results of this model are then used in a quasi-two-dimensional model of laser ablation that accounts for the spatial distribution of intensity in the laser beam. Model predictions are compared with experiments conducted on liquid mercury and excellent agreement is obtained. Based on these results, a simplified model is developed that shows excellent agreement with both the theory and the experiments.

  8. Specific Impulse Definition for Ablative Laser Propulsion

    NASA Technical Reports Server (NTRS)

    Herren, Kenneth A.; Gregory, Don A.

    2004-01-01

    The term "specific impulse" is so ingrained in the field of rocket propulsion that it is unlikely that any fundamental argument would be taken seriously for its removal. It is not an ideal measure but it does give an indication of the amount of mass flow (mass loss/time), as in fuel rate, required to produce a measured thrust over some time period This investigation explores the implications of being able to accurately measure the ablation rate and how the language used to describe the specific impulse results may have to change slightly, and recasts the specific impulse as something that is not a time average. It is not currently possible to measure the ablation rate accurately in real time so it is generally just assumed that a constant amount of material will be removed for each laser pulse delivered The specific impulse dependence on the ablation rate is determined here as a correction to the classical textbook definition.

  9. Characterization of Individual Microneedles Formed on Alloy Surfaces by Femtosecond Laser Ablation

    NASA Astrophysics Data System (ADS)

    Bhattacharya, Sudip; Kam, Dong Hyuck; Song, Lijun; Mazumder, Jyotirmoy

    2012-08-01

    Cross-sectional microstructural analyses of micron/nano-sized structures (termed microneedles) formed by low and high fluence pulse laser ablation of AISI 4340 steel, Ti6Al4V, and Al 5754 alloy specimens were performed. Dependence of length scale and orientation of microneedle microstructures on energy absorptance during laser irradiation, heat transfer direction, absorptivity, and thermal conductivity of the material was established. Microneedle nucleation and growth process were explained based on penetration depths, redeposition of ablated material, and ablation rates.

  10. Laser ablation of ceramic Al{sub 2}O{sub 3} at 193 nm and 248 nm: The importance of single-photon ionization processes

    SciTech Connect

    Pelaez, R. J.; Afonso, C. N.; Bator, M.; Lippert, T.

    2013-06-14

    The aim of this work is to demonstrate that single-photon photoionization processes make a significant difference in the expansion and temperature of the plasma produced by laser ablation of ceramic Al{sub 2}O{sub 3} in vacuum as well as to show their consequences in the kinetic energy distribution of the species that eventually will impact on the film properties produced by pulsed laser deposition. This work compares results obtained by mass spectrometry and optical spectroscopy on the composition and features of the plasma produced by laser ablation at 193 nm and 248 nm, i.e., photon energies that are, respectively, above and below the ionization potential of Al, and for fluences between threshold for visible plasma and up to Almost-Equal-To 2 times higher. The results show that the ionic composition and excitation of the plasma as well as the ion kinetic energies are much higher at 193 nm than at 248 nm and, in the latter case, the population of excited ions is even negligible. The comparison of Maxwell-Boltzmann temperature, electron temperatures, and densities of the plasmas produced with the two laser wavelengths suggests that the expansion of the plasma produced at 248 nm is dominated by a single population. Instead, the one produced at 193 nm is consistent with the existence of two populations of cold and hot species, the latter associated to Al{sup +} ions that travel at the forefront and produced by single photon ionization as well as Al neutrals and double ionized ions produced by electron-ion impact. The results also show that the most energetic Al neutrals in the plasma produced at the two studied wavelengths are in the ground state.

  11. Status of the Ablative Laser Propulsion Studies

    NASA Technical Reports Server (NTRS)

    Herren, Kenneth A.; Lin, Jun; Cohen, Tinothy; Pakhomov, Andrew V.; Thompson, M. Shane

    2004-01-01

    We present a short review of our laser-propulsion research as well as some of the current results of the Ablative Laser Propulsion (ALP) studies currently underway at the University of Alabama in Huntsville. It has been shown that direct surface ablation of a solid material produces high specific impulse (Isp) at relatively high energy conversion efficiency (20 - 40%). We detail measurements of specific impulse, thrust and coupling coefficients for elemental target materials both with single and with double pulse laser shots. We also present measurements taken using three independent methods for determination of Isp. The three methods produce consistent values from ion time-of-flight technique, impulse measurements and imaging of the expansion front of plasma plume. We present a demonstration of our ALP lightcraft, a small free-flying micro-vehicle that is propelled by ablation. For ALP lightcraft we use a subscale thin shell of nickel replicated over a diamond turned mandrel that produces a highly polished self-focusing, truncated at the focus parabolic mirror. The mass of the lightcraft is 54 mg and it is driven by 100-ps wide, 35-mJ laser pulses at 532 nm wavelength. This is an ongoing research. We also present the latest work on laserdriven micro-thrusters and detail some the near term goals of our program.

  12. In vitro investigation on Ho:YAG laser-assisted bone ablation underwater.

    PubMed

    Zhang, Xianzeng; Chen, Chuanguo; Chen, Faner; Zhan, Zhenlin; Xie, Shusen; Ye, Qing

    2016-07-01

    Liquid-assisted hard tissue ablation by infrared lasers has extensive clinical application. However, detailed studies are still needed to explore the underlying mechanism. In the present study, the dynamic process of bubble evolution induced by Ho:YAG laser under water without and with bone tissue at different thickness layer were studied, as well as its effects on hard tissue ablation. The results showed that the Ho:YAG laser was capable of ablating hard bone tissue effectively in underwater conditions. The penetration of Ho:YAG laser can be significantly increased up to about 4 mm with the assistance of bubble. The hydrokinetic forces associated with the bubble not only contributed to reducing the thermal injury to peripheral tissue, but also enhanced the ablation efficiency and improve the ablation crater morphology. The data also presented some clues to optimal selection of irradiation parameters and provided additional knowledge of the bubble-assisted hard tissue ablation mechanism.

  13. Modeling CO{sub 2} Laser Ablative Impulse with Polymers

    SciTech Connect

    Sinko, John E.; Phipps, Claude R.; Sasoh, Akihiro

    2010-10-08

    Laser ablation vaporization models have usually ignored the spatial dependence of the laser beam. Here, we consider effects from modeling using a Gaussian beam for both photochemical and photothermal conditions. The modeling results are compared to experimental and literature data for CO{sub 2} laser ablation of the polymer polyoxymethylene under vacuum, and discussed in terms of the ablated mass areal density and momentum coupling coefficient. Extending the scope of discussion, laser ablative impulse generation research has lacked a cohesive strategy for linking the vaporization and plasma regimes. Existing models, mostly formulated for ultraviolet laser systems or metal targets, appear to be inappropriate or impractical for applications requiring CO{sub 2} laser ablation of polymers. A recently proposed method for linking the vaporization and plasma regimes for analytical modeling is addressed here along with the implications of its use. Key control parameters are considered, along with the major propulsion parameters needed for laser ablation propulsion modeling.

  14. Subcellular analysis by laser ablation electrospray ionization mass spectrometry

    DOEpatents

    Vertes, Akos; Stolee, Jessica A; Shrestha, Bindesh

    2014-12-02

    In various embodiments, a method of laser ablation electrospray ionization mass spectrometry (LAESI-MS) may generally comprise micro-dissecting a cell comprising at least one of a cell wall and a cell membrane to expose at least one subcellular component therein, ablating the at least one subcellular component by an infrared laser pulse to form an ablation plume, intercepting the ablation plume by an electrospray plume to form ions, and detecting the ions by mass spectrometry.

  15. Particle analysis using laser ablation mass spectroscopy

    DOEpatents

    Parker, Eric P.; Rosenthal, Stephen E.; Trahan, Michael W.; Wagner, John S.

    2003-09-09

    The present invention provides a method of quickly identifying bioaerosols by class, even if the subject bioaerosol has not been previously encountered. The method begins by collecting laser ablation mass spectra from known particles. The spectra are correlated with the known particles, including the species of particle and the classification (e.g., bacteria). The spectra can then be used to train a neural network, for example using genetic algorithm-based training, to recognize each spectra and to recognize characteristics of the classifications. The spectra can also be used in a multivariate patch algorithm. Laser ablation mass specta from unknown particles can be presented as inputs to the trained neural net for identification as to classification. The description below first describes suitable intelligent algorithms and multivariate patch algorithms, then presents an example of the present invention including results.

  16. Picosecond laser ablation of poly-L-lactide: Effect of crystallinity on the material response

    SciTech Connect

    Ortiz, Rocio; Quintana, Iban; Etxarri, Jon; Lejardi, Ainhoa; Sarasua, Jose-Ramon

    2011-11-01

    The picosecond laser ablation of poly-L-lactide (PLLA) as a function of laser fluence and degree of crystallinity was examined. The ablation parameters and the surface modifications were analyzed under various irradiation conditions using laser wavelengths ranging from the ultraviolet through the visible. When processing the amorphous PLLA, both energy threshold and topography varied considerably depending on laser wavelength. Laser irradiation showed a reduction in the energy ablation threshold as the degree of crystallinity increased, probably related to photomechanical effects involved in laser ablation with ultra-short pulses and the lower stress accommodation behavior of semicrystalline polymers. In particular, cooperative chain motions are impeded by the higher degree of crystallinity, showing fragile mechanical behavior and lower energy dissipation. The experimental results on ablation rate versus laser energy showed that UV laser ablation on semicrystalline PLLA was more efficient than the visible ablation, i.e., it exhibits higher etch rates over a wide range of pulse energy conditions. These results were interpreted in terms of photo-thermal and photo-chemical response of polymers as a function of material micro-structure and incident laser wavelength. High quality micro-grooves were produced in amorphous PLLA, reveling the potential of ultra-fast laser processing technique in the field of micro-structuring biocompatible and biodegradable polymers for biomedical applications.

  17. Nanochemical effects in femtosecond laser ablation of metals

    SciTech Connect

    Vorobyev, A. Y.; Guo, Chunlei

    2013-02-18

    We study chemical energy released from the oxidation of aluminum in multipulse femtosecond laser ablation in air and oxygen. Our study shows that the released chemical energy amounts to about 13% of the incident laser energy, and about 50% of the ablated material is oxidized. The ablated material mass per laser pulse is measured to be on the nanogram scale. Our study indicates that femtosecond laser ablation is capable of inducing nanochemical reactions since the femtosecond laser pulse can controllably produce nanoparticles, clusters, and atoms from a solid target.

  18. PREFACE AND CONFERENCE INFORMATION: Eighth International Conference on Laser Ablation

    NASA Astrophysics Data System (ADS)

    Hess, Wayne P.; Herman, Peter R.; Bäuerle, Dieter; Koinuma, Hideomi

    2007-04-01

    Laser ablation encompasses a wide range of delicate to extreme light interactions with matter that present considerably challenging problems for scientists to study and understand. At the same time, laser ablation also represents a basic process of significant commercial importance in laser material processing—defining a multi-billion dollar industry today. These topics were widely addressed at the 8th International Conference on Laser Ablation (COLA), held in Banff, Canada on 11-16 September 2005. The meeting took place amongst the majestic and natural beauty of the Canadian Rocky Mountains at The Banff Centre, where delegates enjoyed many inspiring presentations and discussions in a unique campus learning environment. The conference brought together world leading scientists, students and industry representatives to examine the basic science of laser ablation and improve our understanding of the many physical, chemical and/or biological processes driven by the laser. The multi-disciplinary research presented at the meeting underlies some of our most important trends at the forefront of science and technology today that are represented in the papers collected in this volume. Here you will find new processes that are producing novel types of nanostructures and nano-materials with unusual and promising properties. Laser processes are described for delicately manipulating living cells or modifying their internal structure with unprecedented degrees of control and precision. Learn about short-pulse lasers that are driving extreme physical processes on record-fast time scales and opening new directions from material processing applications. The conference papers further highlight forefront application areas in pulsed laser deposition, nanoscience, analytical methods, materials, and microprocessing applications. Laser ablation continues to grow and evolve, touching forefront areas in science and driving new technological trends in laser processing applications. Please

  19. Picosecond laser ablation of nickel-based superalloy C263

    NASA Astrophysics Data System (ADS)

    Semaltianos, N. G.; Perrie, W.; Cheng, J.; French, P.; Sharp, M.; Dearden, G.; Watkins, K. G.

    2010-02-01

    Picosecond laser (10.4 ps, 1064 nm) ablation of the nickel-based superalloy C263 is investigated at different pulse repetition rates (5, 10, 20, and 50 kHz). The two ablation regimes corresponding to ablation dominated by the optical penetration depth at low fluences and of the electron thermal diffusion length at high fluences are clearly identified from the change of the surface morphology of single pulse ablated craters (dimples) with fluence. The two corresponding thresholds were measured as F {th(D1)/1}=0.68±0.02 J/cm2 and F {th(D2)/1}=2.64±0.27 J/cm2 from data of the crater diameters D 1,2 versus peak fluence. The surface morphology of macroscopic areas processed with a scanning laser beam at different fluences is characterised by ripples at low fluences. As the fluence increases, randomly distributed areas among the ripples are formed which appear featureless due to melting and joining of the ripples while at high fluences the whole irradiated surface becomes grainy due to melting, splashing of the melt and subsequent resolidification. The throughput of ablation becomes maximal when machining at high pulse repetition rates and with a relatively low fluence, while at the same time the surface roughness is kept low.

  20. Heat-affected zone of metals ablated with femtosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Hirayama, Yoichi; Obara, Minoru

    2003-07-01

    The melted area is found on the surface ablated by nanosecond and picosecond laser pulses. However, the heat effect is little on the ablated surface in the case of femtosecond laser due to non-thermal ablation process. Heat-affected zone of metallic bulk crystal ablated with femtosecond Ti:sapphire laser pulses is experimentally studied. As a result of XRD (X-ray diffraction) measurements, the XRD peak signal of the area ablated with Ti:sapphire laser becomes smaller than that of the crystalline metal sample. While the crystallinity of the metal sample is crystalline before the laser ablation, the crystallinity in the ablated area is partially changed into the amorphous form. Because the residual pulse energy that is not used for the ablation process remains, leading to the formation of thin layer of melt phase. The melt layer is abruptly cooled down not to be re-crystallized, but to transform into the amorphous form. It is evident that the area ablated with femtosecond laser is changed into the amorphous metal. Additionally XRD measurements and AR+ etching are performed alternately to measure the thickness of the amorphous layer. In the case of iron, the thickness is measured to be 1 μm approximately, therefore heat-affected zone is quite small.

  1. Next generation Er:YAG fractional ablative laser

    NASA Astrophysics Data System (ADS)

    Heinrich, A.; Vizhanyo, A.; Krammer, P.; Summer, S.; Gross, S.; Bragagna, T.; Böhler, C.

    2011-03-01

    Pantec Biosolutions AG presents a portable fractional ablative laser system based on a miniaturized diode pumped Er:YAG laser. The system can operate at repetition rates up to 500 Hz and has an incorporated beam deflection unit. It is smaller, lighter and cost efficient compared to systems based on lamp pumped Er:YAG lasers and incorporates a skin layer detection to guarantee precise control of the microporation process. The pulse parameters enable a variety of applications in dermatology and in general medicine, as demonstrated by first results on transdermal drug delivery of FSH (follicle stimulating hormone).

  2. Thrust Measurements in Ballistic Pendulum Ablative Laser Propulsion Experiments

    SciTech Connect

    Brazolin, H.; Rodrigues, N. A. S.; Minucci, M. A. S.

    2008-04-28

    This paper describes a setup for thrust measurement in ablative laser propulsion experiments, based on a simple ballistic pendulum associated to an imaging system, which is being assembled at IEAv. A light aluminium pendulum holding samples is placed inside a 100 liters vacuum chamber with two optical windows: the first (in ZnSe) for the laser beam and the second (in fused quartz) for the pendulum visualization. A TEA-CO{sub 2} laser beam is focused to the samples providing ablation and transferring linear moment to the pendulum as a whole. A CCD video camera captures the oscillatory movement of the pendulum and the its trajectory is obtained by image processing. By fitting the trajectory of the pendulum to a dumped sinusoidal curve is possible to obtain the amplitude of the movement which is directly related to the momentum transfered to the sample.

  3. Inertial effects in laser-driven ablation

    SciTech Connect

    Harrach, R.J.; Szeoke, A.; Howard, W.M.

    1983-07-15

    The gasdynamic partial differential equations (PDE's) governing the motion of an ablatively accelerated target (rocket) contain an inertial force term that arises from acceleration of the reference frame in which the PDE's are written. We give a simple, intuitive description of this effect, and estimate its magnitude and parametric dependences by means of approximate analytical formulas inferred from our computer hydrocode calculations. Often this inertial term is negligible, but for problems in the areas of laser fusion and laser equation of state studies we find that it can substantially reduce the attainable hydrodynamic efficiency of acceleration and implosion.

  4. Solar cell contact formation using laser ablation

    DOEpatents

    Harley, Gabriel; Smith, David D.; Cousins, Peter John

    2015-07-21

    The formation of solar cell contacts using a laser is described. A method of fabricating a back-contact solar cell includes forming a poly-crystalline material layer above a single-crystalline substrate. The method also includes forming a dielectric material stack above the poly-crystalline material layer. The method also includes forming, by laser ablation, a plurality of contacts holes in the dielectric material stack, each of the contact holes exposing a portion of the poly-crystalline material layer; and forming conductive contacts in the plurality of contact holes.

  5. Solar cell contact formation using laser ablation

    DOEpatents

    Harley, Gabriel; Smith, David D.; Cousins, Peter John

    2014-07-22

    The formation of solar cell contacts using a laser is described. A method of fabricating a back-contact solar cell includes forming a poly-crystalline material layer above a single-crystalline substrate. The method also includes forming a dielectric material stack above the poly-crystalline material layer. The method also includes forming, by laser ablation, a plurality of contacts holes in the dielectric material stack, each of the contact holes exposing a portion of the poly-crystalline materiat layer; and forming conductive contacts in the plurality of contact holes.

  6. Solar cell contact formation using laser ablation

    DOEpatents

    Harley, Gabriel; Smith, David; Cousins, Peter

    2012-12-04

    The formation of solar cell contacts using a laser is described. A method of fabricating a back-contact solar cell includes forming a poly-crystalline material layer above a single-crystalline substrate. The method also includes forming a dielectric material stack above the poly-crystalline material layer. The method also includes forming, by laser ablation, a plurality of contacts holes in the dielectric material stack, each of the contact holes exposing a portion of the poly-crystalline material layer; and forming conductive contacts in the plurality of contact holes.

  7. Spectroscopic characterization approach to study surfactants effect on ZnO 2 nanoparticles synthesis by laser ablation process

    NASA Astrophysics Data System (ADS)

    Drmosh, Q. A.; Gondal, M. A.; Yamani, Z. H.; Saleh, T. A.

    2010-05-01

    Zinc peroxide nanoparticles having grain size less than 5 nm were synthesized using pulsed laser ablation in aqueous solution in the presence of different surfactants and solid zinc target in 3% H 2O 2. The effect of surfactants on the optical and structure of ZnO 2 was studied by applying different spectroscopic techniques. Structural properties and grain size of the synthesized nanoparticles were studied using XRD method. The presence of the cubic phase of zinc peroxide in all samples was confirmed with XRD, and the grain sizes were 4.7, 3.7, 3.3 and 2.8 nm in pure H 2O 2, and H 2O 2 mixed with SDS, CTAB and OGM respectively. For optical characterization, FTIR transmittance spectra of ZnO 2 nanoparticles prepared with and without surfactants show a characteristic ZnO 2 absorption at 435-445 cm -1. FTIR spectrum revealed that the adsorbed surfactants on zinc peroxide disappeared in case of CTAB and OGM while it appears in case of SDS. This could be due to high critical micelles SDS concentration comparing with others which is attributed to the adsorption anionic nature of this surfactant. Both FTIR and UV-vis spectra show a red shift in the presence of SDS and blue shift in the presence of CTAB and OGM. The blue shift in the absorption edge indicates the quantum confinement property of nanoparticles. The zinc peroxide nanoparticles prepared in additives-free media was also characterized by Raman spectra which show the characteristic peaks at 830-840 and 420-440 cm -1.

  8. High throughput laser processing

    SciTech Connect

    Harley, Gabriel; Pass, Thomas; Cousins, Peter John; Viatella, John

    2016-12-27

    A solar cell is formed using a solar cell ablation system. The ablation system includes a single laser source and several laser scanners. The laser scanners include a master laser scanner, with the rest of the laser scanners being slaved to the master laser scanner. A laser beam from the laser source is split into several laser beams, with the laser beams being scanned onto corresponding wafers using the laser scanners in accordance with one or more patterns. The laser beams may be scanned on the wafers using the same or different power levels of the laser source.

  9. In Situ Sr Isotope Analysis of Minerals and Groundmass Using Laser Ablation Multi-collector ICPMS: Potentials for Determining Magma Chamber Processes and Residence Times of Phenocrysts

    NASA Astrophysics Data System (ADS)

    Ramos, F. C.; Wolff, J. A.; Tollstrup, D. L.

    2004-05-01

    In situ analyses of Sr isotope ratios using LA-MC-ICPMS hold great promise for identifying the processes and timescales involved in magmagenesis. The rapid analysis time and spatial control of laser ablation analyses offer significant advantages as compared to modern microdrilling techniques, including substantial time-savings. Laser ablation analyses can constrain the effects of contamination on individual mineral crystals and determine individual crystal residence histories. Integrating these analyses with additional isotopic, major and trace element, and mineralogic data allow us an opportunity to build an integrated magmatic history of the processes affecting magmas. The limited applicability of such LA-MC-ICPMS analyses was typically due to its inability to attain similar measurement precision and accuracy as analyses associated with thermal ionization mass spectrometry (TIMS). We introduce a Sr isotope measurement technique that uses LA-MC-ICPMS to obtain Sr isotope ratios that approach the accuracy and precision offered by TIMS. For marine carbonate, LA-MC-ICPMS results are statistically identical to purified samples analyzed by MC-ICPMS. In addition, we have analyzed common, non-abnormally Sr-enriched minerals from alkalic and tholeiitic basalts such as plagioclase, clinopyroxene, and fine-grained groundmass. Results for basaltic minerals and groundmass are generally within 2 sigma accuracy of microdrilled TIMS results on the same minerals. Results can be combined with simple diffusion models to constrain residence ages of individual minerals in magma chambers or identify the effects of processes such as crustal contamination. In addition, differences in signatures between mineral phases can aid in determining the environments in which different minerals crystallize and may offer the best means by which to constrain magma chamber dynamics.

  10. Spectroscopic characterization of laser ablation brass plasma

    NASA Astrophysics Data System (ADS)

    Shaikh, Nek M.; Hafeez, Sarwat; Kalyar, M. A.; Ali, R.; Baig, M. A.

    2008-11-01

    We present optical emission studies of the laser ablation brass plasma generated by the fundamental, second, and third harmonics of a neodymium doped yttrium aluminum garnet laser. The spectra predominantly reveal the spectral lines of the neutral and singly ionized copper and zinc. The excitation temperatures are determined by the Boltzmann plot method, whereas the electron number densities have been extracted from the Stark broadened line profiles. The spatial variations in the spectral line intensities and the plasma parameters at 1000, 500, and 100 mbar air pressures have been evaluated. Besides, the effect of the ambient gases (He, Ne, and Ar), the laser irradiance, and the laser wavelengths on the plasma parameters have been investigated.

  11. Dynamics of Molecular Emission Features from Nanosecond, Femtosecond Laser and Filament Ablation Plasmas

    SciTech Connect

    Harilal, Sivanandan S.; Yeak, J.; Brumfield, Brian E.; Suter, Jonathan D.; Phillips, Mark C.

    2016-06-15

    The evolutionary paths of molecular species and nanoparticles in laser ablation plumes are not well understood due to the complexity of numerous physical processes that occur simultaneously in a transient laser-plasma system. It is well known that the emission features of ions, atoms, molecules and nanoparticles in a laser ablation plume strongly depend on the laser irradiation conditions. In this letter we report the temporal emission features of AlO molecules in plasmas generated using a nanosecond laser, a femtosecond laser and filaments generated from a femtosecond laser. Our results show that, at a fixed laser energy, the persistence of AlO is found to be highest and lowest in ns and filament laser plasmas respectively while molecular species are formed at early times for both ultrashort pulse (fs and filament) generated plasmas. Analysis of the AlO emission band features show that the vibrational temperature of AlO decays rapidly in filament assisted laser ablation plumes.

  12. Effect of Pulsed Laser Ablation and Continuous Laser Heating on the Adhesion and Cohesion of Cold Sprayed Ti-6Al-4V Coatings

    NASA Astrophysics Data System (ADS)

    Perton, M.; Costil, S.; Wong, W.; Poirier, D.; Irissou, E.; Legoux, J.-G.; Blouin, A.; Yue, S.

    2012-12-01

    The individual and cumulative effects of in situ pulsed laser ablation and continuous laser pre-heating on adhesion and cohesion strength of cold sprayed Ti-6Al-4V coatings are investigated. Laser beams were coupled to a cold spray gun in order to ablate and pre-heat the substrate surface a few milliseconds prior to the impact of the spray particles. Cohesion and adhesion strength were evaluated by scratch test, standard ASTM C633 pull test and laser shock (LASAT) technique. The effects of laser ablation before and during cold spray operations were investigated. Results demonstrate that laser ablation of the substrate before cold spraying led to a smooth surface which improved adhesion strength. However, when laser ablation was maintained throughout the cold spray process, i.e., in between the coating layers, a reduction of cohesion and adhesion was observed. These negative effects were circumvented when laser ablation and laser pre-heating were combined.

  13. An observation of ablation effect of soft biotissue by pulsed Er:YAG laser

    NASA Astrophysics Data System (ADS)

    Zhang, Xianzeng; Xie, Shusen; Ye, Qing; Zhan, Zhenlin

    2007-02-01

    Because of the unique properties with regard to the absorption in organic tissue, pulsed Er:YAG laser has found most interest for various application in medicine, such as dermatology, dentistry, and cosmetic surgery. However, consensus regarding the optimal parameters for clinical use of this tool has not been reached. In this paper, the laser ablation characteristics of soft tissue by Er:YAG laser irradiation was studied. Porcine skin tissue in vitro was used in the experiment. Laser fluences ranged from 25mJ/mm2 to 200mJ/mm2, repetition rates was 5Hz, spot sizes on the tissue surface was 2mm. The ablation effects were assessed by the means of optical microscope, ablation diameters and depths were measured with reading microscope. It was shown that the ablation of soft biotissue by pulsed Er:YAG laser was a threshold process. With appropriate choice of irradiation parameters, high quality ablation with clean, sharp cuts following closely the spatial contour of the incident beam can be achieved. The curves of ablation crater diameter and depth versus laser fluence were obtained, then the ablation threshold and ablation yield were calculated subsequently, and the influence of the number of pulses fired into a crater on ablation crater depth was also discussed.

  14. Micropillar fabrication on bovine cortical bone by direct-write femtosecond laser ablation

    NASA Astrophysics Data System (ADS)

    Lim, Yong C.; Altman, Katrina J.; Farson, Dave F.; Flores, Katharine M.

    2009-11-01

    We investigated fabrication of cylindrical micropillars on bovine cortical bone using direct-write femtosecond laser ablation. The ablation threshold of the material was measured by single-pulse ablation tests, and the incubation coefficient was measured from linear scanned ablation tests. A motion system was programmed to apply multiple layers of concentric rings of pulses to machine pillars of various diameters and heights. The diameter of the top surface of the pillar was found to steadily decrease due to incubation of damage from successive layers of pulses during the machining process. Pillar top diameter was predicted based on a paraxial beam fluence approximation and single-pulse ablation threshold and incubation coefficient measurements. Pillar diameters predicted as successive layers of pulses were applied were well-matched to experiments, confirming that femtosecond laser ablation of the cortical bone was well-modeled by single-pulse ablation threshold measurements and an incubation coefficient.

  15. Low-order harmonic generation in metal ablation plasmas in nanosecond and picosecond laser regimes

    SciTech Connect

    Lopez-Arias, M.; Oujja, M.; Sanz, M.; Castillejo, M.; Ganeev, R. A.; Boltaev, G. S.; Satlikov, N. Kh.; Tugushev, R. I.; Usmanov, T.

    2012-02-15

    Low-order harmonics, third and fifth, of IR (1064 nm) laser emission have been produced in laser ablation plasmas of the metals manganese, copper and silver. The harmonics were generated in a process triggered by laser ablation followed by frequency up-conversion of a fundamental laser beam that propagates parallel to the target surface. These studies were carried out in two temporal regimes by creating the ablation plasma using either nanosecond or picosecond pulses and then probing the plasma plume with pulses of the same duration. The spatiotemporal behavior of the generated harmonics was characterized and reveals the distinct composition and dynamics of the plasma species that act as nonlinear media, allowing the comparison of different processes that control the generation efficiency. These results serve to guide the choice of laser ablation plasmas to be used for efficient high harmonic generation of laser radiation.

  16. Hard tissue ablation with a spray-assisted mid-IR laser.

    PubMed

    Kang, H W; Rizoiu, I; Welch, A J

    2007-12-21

    The objective of this study was to understand the dominant mechanism(s) for dental enamel ablation with the application of water spray. A free-running Er,Cr:YSGG (yttrium, scandium, gallium, garnet) laser was used to ablate human enamel tissue at various radiant exposures. During dental ablation, distilled water was sprayed on the sample surface, and these results were compared to ablation without a spray (dry ablation). In order to identify dominant ablation mechanisms, transient acoustic waves were compared to ablation thresholds and the volume of material removed. The ablation profile and depth were measured using optical coherence tomography (OCT). Irregular surface modification, charring and peripheral cracks were associated with dry ablation, whereas craters for spray samples were relatively clean without thermal damage. In spite of a 60% higher ablation threshold for spray associated irradiations owing to water absorption, acoustic peak pressures were six times higher and ablation volume was up to a factor of 2 larger compared to dry ablation. The enhanced pressure and ablation performance of the spray-assisted process was the result of rapid water vaporization, material ejection with recoil stress, interstitial water explosion and possibly liquid-jet formation. With water cooling and abrasive/disruptive mechanical effects, the spray ablation can be a safe and efficient modality for dental treatment.

  17. Calcified lesion modeling for excimer laser ablation

    NASA Astrophysics Data System (ADS)

    Scott, Holly A.; Archuleta, Andrew; Splinter, Robert

    2009-06-01

    Objective: Develop a representative calcium target model to evaluate penetration of calcified plaque lesions during atherectomy procedures using 308 nm Excimer laser ablation. Materials and Methods: An in-vitro model representing human calcified plaque was analyzed using Plaster-of-Paris and cement based composite materials as well as a fibrinogen model. The materials were tested for mechanical consistency. The most likely candidate(s) resulting from initial mechanical and chemical screening was submitted for ablation testing. The penetration rate of specific multi-fiber catheter designs and a single fiber probe was obtained and compared to that in human cadaver calcified plaque. The effects of lasing parameters and catheter tip design on penetration speed in a representative calcified model were verified against the results in human cadaver specimens. Results: In Plaster of Paris, the best penetration was obtained using the single fiber tip configuration operating at 100 Fluence, 120 Hz. Calcified human lesions are twice as hard, twice as elastic as and much more complex than Plaster of Paris. Penetration of human calcified specimens was highly inconsistent and varied significantly from specimen to specimen and within individual specimens. Conclusions: Although Plaster of Paris demonstrated predictable increases in penetration with higher energy density and repetition rate, it can not be considered a totally representative laser ablation model for calcified lesions. This is in part due to the more heterogeneous nature and higher density composition of cadaver intravascular human calcified occlusions. Further testing will require a more representative model of human calcified lesions.

  18. Simulation of laser interaction with ablative plasma and hydrodynamic behavior of laser supported plasma

    SciTech Connect

    Tong Huifeng; Yuan Hong; Tang Zhiping

    2013-01-28

    When an intense laser beam irradiates on a solid target, ambient air ionizes and becomes plasma, while part of the target rises in temperature, melts, vaporizes, ionizes, and yet becomes plasma. A general Godunov finite difference scheme WENO (Weighted Essentially Non-Oscillatory Scheme) with fifth-order accuracy is used to simulate 2-dimensional axis symmetrical laser-supported plasma flow field in the process of laser ablation. The model of the calculation of ionization degree of plasma and the interaction between laser beam and plasma are considered in the simulation. The numerical simulations obtain the profiles of temperature, density, and velocity at different times which show the evolvement of the ablative plasma. The simulated results show that the laser energy is strongly absorbed by plasma on target surface and that the velocity of laser supported detonation (LSD) wave is half of the ideal LSD value derived from Chapman-Jouguet detonation theory.

  19. Simulation of laser interaction with ablative plasma and hydrodynamic behavior of laser supported plasma

    NASA Astrophysics Data System (ADS)

    Tong, Huifeng; Yuan, Hong; Tang, Zhiping

    2013-01-01

    When an intense laser beam irradiates on a solid target, ambient air ionizes and becomes plasma, while part of the target rises in temperature, melts, vaporizes, ionizes, and yet becomes plasma. A general Godunov finite difference scheme WENO (Weighted Essentially Non-Oscillatory Scheme) with fifth-order accuracy is used to simulate 2-dimensional axis symmetrical laser-supported plasma flow field in the process of laser ablation. The model of the calculation of ionization degree of plasma and the interaction between laser beam and plasma are considered in the simulation. The numerical simulations obtain the profiles of temperature, density, and velocity at different times which show the evolvement of the ablative plasma. The simulated results show that the laser energy is strongly absorbed by plasma on target surface and that the velocity of laser supported detonation (LSD) wave is half of the ideal LSD value derived from Chapman-Jouguet detonation theory.

  20. Laser ablation and high precision patterning of biomaterials and intraocular lenses

    NASA Astrophysics Data System (ADS)

    Serafetinides, A. A.; Spyratou, E.; Makropoulou, M.

    2010-10-01

    The use of intraocular lenses (IOL) is the most promising method for restoring excellent vision in cataract surgery. In addition, multifocal intraocular lenses for good distant and near vision are investigated. Several new materials, techniques and patterns are studied for the formation and etching of intraocular lenses in order to improve their optical properties and reduce the diffractive aberrations. As pulsed laser ablation is well established as a universal tool for surface processing of organic polymer materials, this study was focused in using laser ablation with short and ultra short laser pulses for surface modification of PMMA and intraocular lenses, instead of using other conventional techniques. The main advantage of using very short laser pulses, e.g. of ns, ps or fs duration, is that heat diffusion into the polymer material is negligible. As a result high precision patterning of the sample, without thermal damage of the surroundings, becomes possible. In this study, laser ablation was performed using commercially available hydrophobic acrylic IOLs, hydrophilic acrylic IOLs, and PMMA IOLs, with various diopters. We investigated the ablation efficiency and the phenomenology of the etched patterns by testing the ablation rate, versus laser energy fluence, at several wavelengths and the surface modification with atomic force microscopy (AFM), or scanning electron microscopy (SEM). The irradiated polymers have different optical properties, at the applied wavelengths, and therefore, present different ablation behaviour and morphology of the laser ablated crater walls and surrounding surfaces. The experimental results, some theoretical assumptions for mathematical modeling of the relevant ablation mechanisms are discussed.

  1. Fabrication of silver nanoparticles dispersed in palm oil using laser ablation.

    PubMed

    Zamiri, Reza; Zakaria, Azmi; Ahangar, Hossein Abbastabar; Sadrolhosseini, Amir Reza; Mahdi, Mohd Adzir

    2010-11-22

    In this study we used a laser ablation technique for preparation of silver nanoparticles. The fabrication process was carried out by ablation of a silver plate immersed in palm oil. A pulsed Nd:YAG laser at a wavelength of 1064 nm was used for ablation of the plate at different times. The palm coconut oil allowed formation of nanoparticles with very small and uniform particle size, which are dispersed very homogeneously within the solution. The obtained particle sizes for 15 and 30 minute ablation times were 2.5 and 2 nm, respectively. Stability study shows that all of the samples remained stable for a reasonable period of time.

  2. Analysis of the PMMA and cornea temperature rise during excimer laser ablation

    NASA Astrophysics Data System (ADS)

    Arba-Mosquera, Samuel; Shraiki, Mario

    2010-03-01

    A general method to analyze the ablation temperature for different materials (in particular in the human cornea and poly-methyl-methacrylate (PMMA)) is provided. The model is comprehensive and provides directly laser beam characteristics and ablative spot properties. The model further provides a method to convert the temperature rise during ablation observed in PMMA to equivalent temperature rises in the cornea. The proposed model can be used for calibration, verification and validation purposes of laser systems used for ablation processes at relatively low cost and would directly improve the quality of results.

  3. Ultrafast properties of femtosecond-laser-ablated GaAs and its application to terahertz optoelectronics.

    PubMed

    Madéo, Julien; Margiolakis, Athanasios; Zhao, Zhen-Yu; Hale, Peter J; Man, Michael K L; Zhao, Quan-Zhong; Peng, Wei; Shi, Wang-Zhou; Dani, Keshav M

    2015-07-15

    We report on the first terahertz (THz) emitter based on femtosecond-laser-ablated gallium arsenide (GaAs), demonstrating a 65% enhancement in THz emission at high optical power compared to the nonablated device. Counter-intuitively, the ablated device shows significantly lower photocurrent and carrier mobility. We understand this behavior in terms of n-doping, shorter carrier lifetime, and enhanced photoabsorption arising from the ablation process. Our results show that laser ablation allows for efficient and cost-effective optoelectronic THz devices via the manipulation of fundamental properties of materials.

  4. Physical mechanisms of SiN{sub x} layer structuring with ultrafast lasers by direct and confined laser ablation

    SciTech Connect

    Rapp, S.; Heinrich, G.; Wollgarten, M.; Huber, H. P.; Schmidt, M.

    2015-03-14

    In the production process of silicon microelectronic devices and high efficiency silicon solar cells, local contact openings in thin dielectric layers are required. Instead of photolithography, these openings can be selectively structured with ultra-short laser pulses by confined laser ablation in a fast and efficient lift off production step. Thereby, the ultrafast laser pulse is transmitted by the dielectric layer and absorbed at the substrate surface leading to a selective layer removal in the nanosecond time domain. Thermal damage in the substrate due to absorption is an unwanted side effect. The aim of this work is to obtain a deeper understanding of the physical laser-material interaction with the goal of finding a damage-free ablation mechanism. For this, thin silicon nitride (SiN{sub x}) layers on planar silicon (Si) wafers are processed with infrared fs-laser pulses. Two ablation types can be distinguished: The known confined ablation at fluences below 300 mJ/cm{sup 2} and a combined partial confined and partial direct ablation at higher fluences. The partial direct ablation process is caused by nonlinear absorption in the SiN{sub x} layer in the center of the applied Gaussian shaped laser pulses. Pump-probe investigations of the central area show ultra-fast reflectivity changes typical for direct laser ablation. Transmission electron microscopy results demonstrate that the Si surface under the remaining SiN{sub x} island is not damaged by the laser ablation process. At optimized process parameters, the method of direct laser ablation could be a good candidate for damage-free selective structuring of dielectric layers on absorbing substrates.

  5. Deflection of uncooperative targets using laser ablation

    NASA Astrophysics Data System (ADS)

    Thiry, Nicolas; Vasile, Massimiliano

    2015-09-01

    Owing to their ability to move a target in space without requiring propellant, laser-based deflection methods have gained attention among the research community in the recent years. With laser ablation, the vaporized material is used to push the target itself allowing for a significant reduction in the mass requirement for a space mission. Specifically, this paper addresses two important issues which are thought to limit seriously the potential efficiency of a laser-deflection method: the impact of the tumbling motion of the target as well as the impact of the finite thickness of the material ablated in the case of a space debris. In this paper, we developed a steady-state analytical model based on energetic considerations in order to predict the efficiency range theoretically allowed by a laser deflection system in absence of the two aforementioned issues. A numerical model was then implemented to solve the transient heat equation in presence of vaporization and melting and account for the tumbling rate of the target. This model was also translated to the case where the target is a space debris by considering material properties of an aluminium 6061-T6 alloy and adapting at every time-step the size of the computational domain along with the recession speed of the interface in order to account for the finite thickness of the debris component. The comparison between the numerical results and the analytical predictions allow us to draw interesting conclusions regarding the momentum coupling achievable by a given laser deflection system both for asteroids and space debris in function of the flux, the rotation rate of the target and its material properties. In the last section of this paper, we show how a reasonably small spacecraft could deflect a 56m asteroid with a laser system requiring less than 5kW of input power.

  6. Femtosecond laser processing and spatial light modulator

    NASA Astrophysics Data System (ADS)

    Paivasaari, Kimmo; Silvennoinen, Martti; Kaakkunen, Jarno; Vahimaa, Pasi

    2014-03-01

    The use of the femtosecond laser enables generation of small spot sizes and ablation features. Ablation of the small features usually requires only a small amount of laser power to be delivered to the ablation spot. When using only a one beam for the ablation of the small features this process is bound to be time consuming. The spatial light modulator (SLM) together with the computer generated holograms (CGH) can be used for manipulating and shaping of the laser beam in various applications. In laser micromachining, when using laser with relatively high power, the original beam can be divided up to hundreds beams and still have the energy of the individual beam above the ablation threshold of the material. This parallel laser processing enables more efficient use of the laser power regardless of the machining task.

  7. Subsurface ablation of atherosclerotic plaque using ultrafast laser pulses

    PubMed Central

    Lanvin, Thomas; Conkey, Donald B.; Frobert, Aurelien; Valentin, Jeremy; Goy, Jean-Jacques; Cook, Stéphane; Giraud, Marie-Noelle; Psaltis, Demetri

    2015-01-01

    We perform subsurface ablation of atherosclerotic plaque using ultrafast pulses. Excised mouse aortas containing atherosclerotic plaque were ablated with ultrafast near-infrared (NIR) laser pulses. Optical coherence tomography (OCT) was used to observe the ablation result, while the physical damage was inspected in histological sections. We characterize the effects of incident pulse energy on surface damage, ablation hole size, and filament propagation. We find that it is possible to ablate plaque just below the surface without causing surface damage, which motivates further investigation of ultrafast ablation for subsurface atherosclerotic plaque removal. PMID:26203381

  8. Subsurface ablation of atherosclerotic plaque using ultrafast laser pulses.

    PubMed

    Lanvin, Thomas; Conkey, Donald B; Frobert, Aurelien; Valentin, Jeremy; Goy, Jean-Jacques; Cook, Stéphane; Giraud, Marie-Noelle; Psaltis, Demetri

    2015-07-01

    We perform subsurface ablation of atherosclerotic plaque using ultrafast pulses. Excised mouse aortas containing atherosclerotic plaque were ablated with ultrafast near-infrared (NIR) laser pulses. Optical coherence tomography (OCT) was used to observe the ablation result, while the physical damage was inspected in histological sections. We characterize the effects of incident pulse energy on surface damage, ablation hole size, and filament propagation. We find that it is possible to ablate plaque just below the surface without causing surface damage, which motivates further investigation of ultrafast ablation for subsurface atherosclerotic plaque removal.

  9. Excimer laser ablation of thick SiOx-films: Etch rate measurements and simulation of the ablation threshold

    NASA Astrophysics Data System (ADS)

    Ihlemann, J.; Meinertz, J.; Danev, G.

    2012-08-01

    Excimer laser ablation of 4.5 μm thick SiOx-films with x ≈ 1 is investigated at 193 nm, 248 nm, and 308 nm. Strong absorption enables precisely tunable removal depths. The ablation rates correlate with laser penetration depths calculated from low level absorption coefficients. The experimental ablation thresholds are in agreement with numerical simulations on the basis of linear absorption and one-dimensional heat flow. This behaviour is similar to that of strongly UV-absorbing polymers, leading to well controllable micro machining prospects. After laser processing, SiOx can be converted to SiO2, opening a route to laser based fabrication of micro optical components.

  10. Antibacterial effects of laser ablated Ni nanoparticles

    NASA Astrophysics Data System (ADS)

    Shamaila, S.; Wali, H.; Sharif, R.; Nazir, J.; Zafar, N.; Rafique, M. S.

    2013-10-01

    The interaction of nickel nanoparticles with Escherichia coli (E. coli) bacteria has been studied. The nickel nanoparticles have been fabricated by continuous wave laser ablation of nickel target and their properties are studied using different characterization techniques. The antibacterial activity of nickel nanoparticles was checked against E. coli bacteria. Escherichia coli were cultured in nutrients broth and different concentrations of nickel nanoparticles were added to bacterial culture solution to investigate the interaction of nickel nanoparticles with bacteria and to check toxicity of the nickel nanoparticles against E. coli. The fabricated Ni nanoparticles have exhibited considerable antimicrobial activity against E. coli.

  11. Laser ablation of liquid surface in air induced by laser irradiation through liquid medium

    NASA Astrophysics Data System (ADS)

    Utsunomiya, Yuji; Kajiwara, Takashi; Nishiyama, Takashi; Nagayama, Kunihito; Kubota, Shiro; Nakahara, Motonao

    2010-10-01

    The pulse laser ablation of a liquid surface in air when induced by laser irradiation through a liquid medium has been experimentally investigated. A supersonic liquid jet is observed at the liquid-air interface. The liquid surface layer is driven by a plasma plume that is produced by laser ablation at the layer, resulting in a liquid jet. This phenomenon occurs only when an Nd:YAG laser pulse (wavelength: 1064 nm) is focused from the liquid onto air at a low fluence of 20 J/cm2. In this case, as Fresnel’s law shows, the incident and reflected electric fields near the liquid surface layer are superposed constructively. In contrast, when the incident laser is focused from air onto the liquid, a liquid jet is produced only at an extremely high fluence, several times larger than that in the former case. The similarities and differences in the liquid jets and atomization processes are studied for several liquid samples, including water, ethanol, and vacuum oil. The laser ablation of the liquid surface is found to depend on the incident laser energy and laser fluence. A pulse laser light source and high-resolution film are required to observe the detailed structure of a liquid jet.

  12. INTERACTION OF LASER RADIATION WITH MATTER: Effect of the pulse duration on graphitisation of diamond during laser ablation

    NASA Astrophysics Data System (ADS)

    Kononenko, Vitalii V.; Kononenko, Taras V.; Pimenov, S. M.; Sinyavskii, M. N.; Konov, Vitalii I.; Dausinger, F.

    2005-03-01

    Processes of graphitisation of laser-irradiated polycrystalline diamond surface exposed to multipulse irradiation are studied experimentally. The thickness of the laser-modified layer as a function of the laser-pulse duration ranging from 100 fs to 1.5 μs and the effect of the radiation wavelength on this thickness are studied. It is shown that the diamond graphitisation during multipulse laser ablation is a thermally stimulated process. The dependences of the diamond-ablation rates on the radiation energy density under the action of laser pulses of various durations are presented.

  13. Ablative skin resurfacing with a novel microablative CO2 laser.

    PubMed

    Gotkin, Robert H; Sarnoff, Deborah S; Cannarozzo, Giovanni; Sadick, Neil S; Alexiades-Armenakas, Macrene

    2009-02-01

    Carbon dioxide (CO2) laser skin resurfacing has been a mainstay of facial rejuvenation since its introduction in the mid 1990s. Recently, a new generation of fractional or microablative CO2 lasers has been introduced to the marketplace. According to the concept of fractional photothermolysis, these lasers ablate only a fraction of the epidermal and dermal architecture in the treatment area. An array of microscopic thermal wounds is created that ablates the epidermis and dermis within very tiny zones; adjacent to these areas, the epidermis and dermis are spared. This microablative process of laser skin resurfacing has proven safe and effective not only for facial rejuvenation, but elsewhere on the body as well. It is capable of improving wrinkles, acne scars, and other types of atrophic scars and benign pigmented lesions associated with elastotic, sun-damaged skin. Because of the areas of spared epidermis and dermis inherent in a procedure that employs fractional photothermolysis, healing is more rapid compared to fully ablative CO2 laser skin resurfacing and downtime is proportionately reduced. A series of 32 consecutive patients underwent a single laser resurfacing procedure with the a new microablative CO2 laser. All patients were followed for a minimum of 6 months and were asked to complete patient satisfaction questionnaires; a 6 month postoperative photographic evaluation by an independent physician, not involved in the treatment, was also performed. Both sets of data were graded and reported on a quartile scale. Results demonstrated greater than 50% improvement in almost all patients with those undergoing treatment for wrinkles, epidermal pigment or solar elastosis deriving the greatest change for the better (>75%).

  14. Bioavailable nanoparticles obtained in laser ablation of a selenium target in water

    SciTech Connect

    Kuzmin, P G; Shafeev, Georgii A; Voronov, Valerii V; Raspopov, R V; Arianova, E A; Trushina, E N; Gmoshinskii, I V; Khotimchenko, S A

    2012-11-30

    The process of producing colloidal solutions of selenium nanoparticles in water using the laser ablation method is described. The prospects of using nanoparticles of elementary selenium as a nutrition source of this microelement are discussed. (nanoparticles)

  15. Investigation of laser-induced ablation of ceramic materials for spaceborne applications

    NASA Astrophysics Data System (ADS)

    Schroeder, H.; Hippler, M.; Allenspacher, P.; Riede, W.; Ciapponi, A.; Mateo, A. B.; Ivanov, T.; Alves, J.; Piris, J.; Heese, C.; Wernham, D.

    2016-12-01

    In this work tests for determination of ablation thresholds of various ceramic materials for pulsed laser irradiations at wavelengths of 355 nm and 1064 nm in vacuum are presented. For comparison tests with copper and aluminium are also reported. The ablation process was monitored insitu by long-distance microscopy. The morphology of ablation spots was exsitu inspected by scanning electron microscopy. Furthermore, the redeposition of potentially released particles on optics in the vicinity to the target was examined.

  16. Mid-infrared laser ablation of intraocular acrylic lenses

    NASA Astrophysics Data System (ADS)

    Spyratou, E.; Makropoulou, M.; Bacharis, C.; Serafetinides, A. A.

    2007-05-01

    Ablation rates measurements with free-running Er:YAG laser (λ=2.94 μm) were performed in hydrophilic acrylic intraocular lenses. We studied the role of water in the laser ablation mechanisms by using hydrophilic lenses with different concentrations of H II0 and D II0. A mathematical model simulated the experimental results.

  17. Analysis of fabric materials cut using ultraviolet laser ablation

    NASA Astrophysics Data System (ADS)

    Tsai, Hsin-Yi; Yang, Chih-Chung; Hsiao, Wen-Tse; Huang, Kuo-Cheng; Andrew Yeh, J.

    2016-04-01

    Laser ablation technology has widely been applied in the clothing industry in recent years. However, the laser mechanism would affect the quality of fabric contours and its components. Hence, this study examined carbonization and oxidation conditions and contour variation in nonwoven, cotton, and composite leather fabrics cut by using an ultraviolet laser at a wavelength of 355 nm. Processing parameters such as laser power, pulse frequency, scanning speed, and number of pulses per spot were adjusted to investigate component variation of the materials and to determine suitable cutting parameters for the fabrics. The experimental results showed that the weights of the component changed substantially by pulse frequency but slightly by laser power, so pulse frequency of 100 kHz and laser power of 14 W were the approximate parameters for three fabrics for the smaller carbonization and a sufficient energy for rapidly cutting, which the pulse duration of laser system was fixed at 300 μs and laser irradiance was 0.98 J/mm2 simultaneously. In addition, the etiolate phenomenon of nonwoven was reduced, and the component weight of cotton and composite leather was closed to the value of knife-cut fabric as the scanning speed increased. The approximate scanning speed for nonwoven and composite leather was 200 mm/s, and one for cotton was 150 mm/s, respectively. The sharper and firmer edge is obtained by laser ablation mechanism in comparison with traditional knife cutting. Experimental results can serve as the reference for laser cutting in the clothing industry, for rapidly providing smoother patterns with lower carbonization and oxidation edge in the fashion industry.

  18. Laser-Ablation (U-Th)/He Geochronology

    NASA Astrophysics Data System (ADS)

    Hodges, K.; Boyce, J.

    2003-12-01

    Over the past decade, ultraviolet laser microprobes have revolutionized the field of 40Ar/39Ar geochronology. They provide unprecedented information about Ar isotopic zoning in natural crystals, permit high-resolution characterization of Ar diffusion profiles produced during laboratory experiments, and enable targeted dating of multiple generations of minerals in thin section. We have modified the analytical protocols used for 40Ar/39Ar laser microanalysis for use in (U-Th)/He geochronologic studies. Part of the success of the 40Ar/39Ar laser microprobe stems from fact that measurements of Ar isotopic ratios alone are sufficient for the calculation of a date. In contrast, the (U-Th)/He method requires separate analysis of U+Th and 4He. Our method employs two separate laser microprobes for this process. A target mineral grain is placed in an ultrahigh vacuum chamber fitted with a window of appropriate composition to transmit ultraviolet radiation. A focused ArF (193 nm) excimer laser is used to ablate tapered cylindrical pits on the surface of the target. The liberated material is scrubbed with a series of getters in a fashion similar to that used for 40Ar/39Ar geochronology, and the 4He abundance is determined using a quadrupole mass spectrometer with well-calibrated sensitivity. A key requirement for calculation of the 4He abundance in the target is a precise knowledge of the volume of the ablation pit. This is the principal reason why we employ the ArF excimer for 4He analysis rather than a less-expensive frequency-multiplied Nd-YAG laser; the excimer creates tapered cylindrical pits with extremely reproducible and easily characterized geometry. After 4He analysis, U and Th are measured on the same sample surface using the more familiar technique of laser-ablation inductively coupled plasma mass spectrometry (LA-ICPMS). Our early experiments have been done using a frequency-quintupled Nd-YAG microprobe (213nm), While the need to analyze U+Th and He in separate

  19. Laser ablation plume dynamics in nanoparticle synthesis

    SciTech Connect

    Osipov, V V; Platonov, V V; Lisenkov, V V

    2009-06-30

    The dynamics of the plume ejected from the surface of solid targets (YSZ, Nd:YAG and graphite) by a CO{sub 2} laser pulse with a duration of {approx}500 {mu}s (at the 0.03 level), energy of 1.0-1.3 J and peak power of 6-7 kW have been studied using high-speed photography of the plume luminescence and shadow. The targets were used to produce nanopowders by laser evaporation. About 200 {mu}s after termination of the pulse, shadowgraph images of the plumes above the YSZ and Nd:YAG targets showed dark straight tracks produced by large particles. The formation of large ({approx}10 {mu}m) particles is tentatively attributed to cracking of the solidified melt at the bottom of the ablation crater. This is supported by the fact that no large particles are ejected from graphite, which sublimes without melting. Further support to this hypothesis is provided by numerical 3D modelling of melt cooling in craters produced by laser pulses of different shapes. (interaction of laser radiation with matter. laser plasma)

  20. Q-switched 1064nm laser source for photomechanical ablation in obsidianus lapis

    NASA Astrophysics Data System (ADS)

    Aguilar-Morales, A. I.; Álvarez-Chávez, J. A.; Morales-Ramírez, A. J.; Panzner, Michael; Ortega-Delgado, M. A.

    2015-09-01

    The process of ablation in obsidianus lapis is mainly governed by pulse energy from the laser source and scanning speed. The rate of material ablation is influenced by chemical and physical properties. In this work, laser energy at 1064 nm, has been used for ablation behavior in Q-switch regime. A >40 W, average power Nd:YAG source with pulse energies ranging from 3mJ to nearly 7 mJ, achieved surface damages up to 160 μm of depth. Photo-mechanical ablation in terms of scan speed showed a maximum depth of nearly 500 μm at 130 mm/s. The maximum pulse energy of 12 mJ resulted in ablation of 170 μm depth. Highly efficient ablation in obsidianus lapis for artistic work is an interesting field of application.

  1. Numerical study of the thermal ablation of wet solids by ultrashort laser pulses

    SciTech Connect

    Perez, Danny; Beland, Laurent Karim; Deryng, Delphine; Lewis, Laurent J.; Meunier, Michel

    2008-01-01

    The ablation by ultrashort laser pulses at relatively low fluences (i.e., in the thermal regime) of solids wetted by a thin liquid film is studied using a generic numerical model. In comparison with dry targets, the liquid is found to significantly affect ablation by confining the solid and slowing down the expansion of the laser-heated material. These factors affect the relative efficiency of the various ablation mechanisms, leading, in particular, to the complete inhibition of phase explosion at lower fluences, a reduced ablation yield, and significant changes in the composition of the plume. As a consequence, at fluences above the ablation threshold, the size of the ejected nanoclusters is lower in presence of the liquid. Our results provide a qualitative understanding of the effect of wetting layers on the ablation process.

  2. Research and application of surface heat treatment for multipulse laser ablation of materials

    NASA Astrophysics Data System (ADS)

    Cai, Song; Chen, Genyu; Zhou, Cong

    2015-11-01

    This study analysed a laser ablation platform and built heat transfer equations for multipulse laser ablation of materials. The equations include three parts: laser emission after the material melt and gasification; end of laser emission after the material melts and there is the presence of a super-hot layer and solid-phase heat transfer changes during material ablation. For each of the three parts, the effects of evaporation, plasma shielding and energy accumulation under the pulse interval were considered. The equations are reasonable, and all the required parameters are only related to the laser parameters and material properties, allowing the model to have a certain versatility and practicability. The model was applied for numerical simulation of the heat transfer characteristics in the multipulse laser ablation of bronze and diamond. Next, experiments were conducted to analyse the topography of a bronze-bonded diamond grinding wheel after multipulse laser ablation. The theoretical analysis and experimental results showed that multipulse laser can merge the truing and dressing on a bronze-bonded diamond grinding wheel. This study provides theoretical guidance for optimising the process parameters in the laser ablation of a bronze-bonded diamond grinding wheel. A comparative analysis showed that the numerical solution to the model is in good agreement with the experimental data, thus verifying the correctness and feasibility of the heat transfer model.

  3. Measurements of erbium laser-ablation efficiency in hard dental tissues under different water cooling conditions.

    PubMed

    Kuščer, Lovro; Diaci, Janez

    2013-10-01

    Laser triangulation measurements of Er:YAG and Er,Cr:YSGG laser-ablated volumes in hard dental tissues are made, in order to verify the possible existence of a "hydrokinetic" effect that has been proposed as an alternative to the "subsurface water expansion" mechanism for hard-tissue laser ablation. No evidence of the hydrokinetic effect could be observed under a broad range of tested laser parameters and water cooling conditions. On the contrary, the application of water spray during laser exposure of hard dental material is observed to diminish the laser-ablation efficiency (AE) in comparison with laser exposure under the absence of water spray. Our findings are in agreement with the generally accepted principle of action for erbium laser ablation, which is based on fast subsurface expansion of laser-heated water trapped within the interstitial structure of hard dental tissues. Our measurements also show that the well-known phenomenon of ablation stalling, during a series of consecutive laser pulses, can primarily be attributed to the blocking of laser light by the loosely bound and recondensed desiccated minerals that collect on the tooth surface during and following laser ablation. In addition to the prevention of tooth bulk temperature buildup, a positive function of the water spray that is typically used with erbium dental lasers is to rehydrate these minerals, and thus sustaining the subsurface expansion ablation process. A negative side effect of using a continuous water spray is that the AE gets reduced due to the laser light being partially absorbed in the water-spray particles above the tooth and in the collected water pool on the tooth surface. Finally, no evidence of the influence of the water absorption shift on the hypothesized increase in the AE of the Er,Cr:YSGG wavelength is observed.

  4. Flow speed of the ablation vapors generated during laser drilling of CFRP with a continuous-wave laser beam

    NASA Astrophysics Data System (ADS)

    Faas, S.; Freitag, C.; Boley, S.; Berger, P.; Weber, R.; Graf, T.

    2017-03-01

    The hot plume of ablation products generated during the laser drilling process of carbon fiber reinforced plastics (CFRP) with a continuous-wave laser beam was analyzed by means of high-speed imaging. The formation of compression shocks was observed within the flow of the evaporated material, which is an indication of flow speeds well above the local speed of sound. The flow speed of the hot ablation products can be estimated by analyzing the position of these compression shocks. We investigated the temporal evolution of the flow speed during the drilling process and the influence of the average laser power on the flow speed. The flow speed increases with increasing average laser powers. The moment of drilling through the material changes the conditions for the drilling process and was confirmed to influence the flow speed of the ablated material. Compression shocks can also be observed during laser cutting of CFRP with a moving laser beam.

  5. Water content contribution in calculus phantom ablation during Q-switched Tm:YAG laser lithotripsy.

    PubMed

    Zhang, Jian J; Rajabhandharaks, Danop; Xuan, Jason Rongwei; Wang, Hui; Chia, Ray W J; Hasenberg, Tom; Kang, Hyun Wook

    2015-01-01

    Q-switched (QS) Tm:YAG laser ablation mechanisms on urinary calculi are still unclear to researchers. Here, dependence of water content in calculus phantom on calculus ablation performance was investigated. White gypsum cement was used as a calculus phantom model. The calculus phantoms were ablated by a total 3-J laser pulse exposure (20 mJ, 100 Hz, 1.5 s) and contact mode with N=15 sample size. Ablation volume was obtained on average 0.079, 0.122, and 0.391  mm3 in dry calculus in air, wet calculus in air, and wet calculus in-water groups, respectively. There were three proposed ablation mechanisms that could explain the effect of water content in calculus phantom on calculus ablation performance, including shock wave due to laser pulse injection and bubble collapse, spallation, and microexplosion. Increased absorption coefficient of wet calculus can cause stronger spallation process compared with that caused by dry calculus; as a result, higher calculus ablation was observed in both wet calculus in air and wet calculus in water. The test result also indicates that the shock waves generated by short laser pulse under the in-water condition have great impact on the ablation volume by Tm:YAG QS laser.

  6. Precise ablation of dental hard tissues with ultra-short pulsed lasers. Preliminary exploratory investigation on adequate laser parameters.

    PubMed

    Bello-Silva, Marina Stella; Wehner, Martin; Eduardo, Carlos de Paula; Lampert, Friedrich; Poprawe, Reinhart; Hermans, Martin; Esteves-Oliveira, Marcella

    2013-01-01

    This study aimed to evaluate the possibility of introducing ultra-short pulsed lasers (USPL) in restorative dentistry by maintaining the well-known benefits of lasers for caries removal, but also overcoming disadvantages, such as thermal damage of irradiated substrate. USPL ablation of dental hard tissues was investigated in two phases. Phase 1--different wavelengths (355, 532, 1,045, and 1,064 nm), pulse durations (picoseconds and femtoseconds) and irradiation parameters (scanning speed, output power, and pulse repetition rate) were assessed for enamel and dentin. Ablation rate was determined, and the temperature increase measured in real time. Phase 2--the most favorable laser parameters were evaluated to correlate temperature increase to ablation rate and ablation efficiency. The influence of cooling methods (air, air-water spray) on ablation process was further analyzed. All parameters tested provided precise and selective tissue ablation. For all lasers, faster scanning speeds resulted in better interaction and reduced temperature increase. The most adequate results were observed for the 1064-nm ps-laser and the 1045-nm fs-laser. Forced cooling caused moderate changes in temperature increase, but reduced ablation, being considered unnecessary during irradiation with USPL. For dentin, the correlation between temperature increase and ablation efficiency was satisfactory for both pulse durations, while for enamel, the best correlation was observed for fs-laser, independently of the power used. USPL may be suitable for cavity preparation in dentin and enamel, since effective ablation and low temperature increase were observed. If adequate laser parameters are selected, this technique seems to be promising for promoting the laser-assisted, minimally invasive approach.

  7. Renaissance of laser interstitial thermal ablation.

    PubMed

    Missios, Symeon; Bekelis, Kimon; Barnett, Gene H

    2015-03-01

    Laser interstitial thermal therapy (LITT) is a minimally invasive technique for treating intracranial tumors, originally introduced in 1983. Its use in neurosurgical procedures was historically limited by early technical difficulties related to the monitoring and control of the extent of thermal damage. The development of magnetic resonance thermography and its application to LITT have allowed for real-time thermal imaging and feedback control during laser energy delivery, allowing for precise and accurate provision of tissue hyperthermia. Improvements in laser probe design, surgical stereotactic targeting hardware, and computer monitoring software have accelerated acceptance and clinical utilization of LITT as a neurosurgical treatment alternative. Current commercially available LITT systems have been used for the treatment of neurosurgical soft-tissue lesions, including difficult to access brain tumors, malignant gliomas, and radiosurgery-resistant metastases, as well as for the ablation of such lesions as epileptogenic foci and radiation necrosis. In this review, the authors aim to critically analyze the literature to describe the advent of LITT as a neurosurgical, laser excision tool, including its development, use, indications, and efficacy as it relates to neurosurgical applications.

  8. Energy balance in laser ablation of metal targets

    SciTech Connect

    Sobral, H.; Villagran-Muniz, M.; Bredice, F.

    2005-10-15

    Laser-generated plasma was induced on metallic targets glued to a piezoelectric microphone and placed between the plates of a planar charged capacitor. The plasma generates a temporal redistribution of electric charge on the plates that can easily be measured by a resistor connected to the ground plate; this signal is proportional to the total number of ions removed by breakdown. Both the absorbed and scattered energies were simultaneously monitored by the photoacoustic signal and an energy meter. From these signals it was possible to determine the energy involved in each of the processes. Just above the ablation threshold most of the delivered energy is absorbed and the acoustic signal prevails compared to other contributions. Above this region, the electric signal, which is proportional to the energy involved in the ablation process, becomes dominant.

  9. Plume collimation for laser ablation electrospray ionization mass spectrometry

    DOEpatents

    Vertes, Akos; Stolee, Jessica A.

    2016-06-07

    In various embodiments, a device may generally comprise a capillary having a first end and a second end; a laser to emit energy at a sample in the capillary to ablate the sample and generate an ablation plume in the capillary; an electrospray apparatus to generate an electrospray plume to intercept the ablation plume to produce ions; and a mass spectrometer having an ion transfer inlet to capture the ions. The ablation plume may comprise a collimated ablation plume. The device may comprise a flow cytometer. Methods of making and using the same are also described.

  10. Plume collimation for laser ablation electrospray ionization mass spectrometry

    DOEpatents

    Vertes, Akos; Stolee, Jessica A.

    2014-09-09

    In various embodiments, a device may generally comprise a capillary having a first end and a second end; a laser to emit energy at a sample in the capillary to ablate the sample and generate an ablation plume in the capillary; an electrospray apparatus to generate an electrospray plume to intercept the ablation plume to produce ions; and a mass spectrometer having an ion transfer inlet to capture the ions. The ablation plume may comprise a collimated ablation plume. The device may comprise a flow cytometer. Methods of making and using the same are also described.

  11. Laser-induced shockwave propagation from ablation in a cavity

    SciTech Connect

    Zeng Xianzhong; Mao Xianglei; Mao, Samuel S.; Wen, S.-B.; Greif, Ralph; Russo, Richard E.

    2006-02-06

    The propagation of laser-induced shockwaves from ablation inside of cavities was determined from time-resolved shadowgraph images. The temperature and electron number density of the laser-induced plasma was determined from spectroscopic measurements. These properties were compared to those for laser ablation on the flat surface under the same energy and background gas condition. A theoretical model was proposed to determine the amount of energy and vaporized mass stored in the vapor plume based on these measurements.

  12. A study of particle generation during laser ablation with applications

    SciTech Connect

    Liu, Chunyi

    2005-01-01

    A study has been made of the generation of particles during laser ablation and has included size distribution measurements and observation of the formation processes. The particle size distribution with respect to different laser parameters was obtained in-line using a differential mobility analyzer (DMA) and a particle counter. The experimental results show that the particle size varies with laser energy, laser pulsewidth, ambient gas flow rate and sample properties. The results serve as a basis for controlling the size of nanoparticles generated by laser ablation. Laser shadowgraph imaging was used to study mass ejection processes and mechanisms. At higher laser irradiance, some particles were ejected in the liquid and even in the solid phase. Time-resolved images show the propagation of the shockwaves: external shockwaves propagate outward and decelerate, and internal shockwaves reflect back and forth between the gas contact surface and the sample surface. The internal shockwave is proposed to cause the ejection of liquid particles when the internal shockwave strikes the liquid molten layer. A simulation based on vapor plume expansion was carried out and provides satisfactory agreement with experimental results. Different material properties result in different particle ejection behavior:particle ejection for most materials including metals result in a conically shaped envelope for the ejected material while ejection for silicon resembles a liquid jet. The difference in density change when the materials melt was proposed to be an important factor in the different ejection behavior. The characteristics of particles generated by laser ablation have a strong influence on the chemical analysis of the irradiated sample. Large particles are more difficult to completely vaporize and ionize, and induced preferential vaporization causes fractionation (i.e. a detected chemical composition that differs from the sample material). Large particles also result in spikes in

  13. Laser ablation system, and method of decontaminating surfaces

    DOEpatents

    Ferguson, Russell L.; Edelson, Martin C.; Pang, Ho-ming

    1998-07-14

    A laser ablation system comprising a laser head providing a laser output; a flexible fiber optic cable optically coupled to the laser output and transmitting laser light; an output optics assembly including a nozzle through which laser light passes; an exhaust tube in communication with the nozzle; and a blower generating a vacuum on the exhaust tube. A method of decontaminating a surface comprising the following steps: providing an acousto-optic, Q-switched Nd:YAG laser light ablation system having a fiber optically coupled output optics assembly; and operating the laser light ablation system to produce an irradiance greater than 1.times.10.sup.7 W/cm.sup.2, and a pulse width between 80 and 170 ns.

  14. Human cornea wound healing in organ culture after Er:YAG laser ablation

    NASA Astrophysics Data System (ADS)

    Shen, Jin-Hui; Joos, Karen M.; Robinson, Richard D.; Shetlar, Debra J.; O'Day, Denis M.

    1998-06-01

    Purpose: To study the healing process in cultured human corneas after Er:YAG laser ablation. Methods: Human cadaver corneas within 24 hours post mortem were ablated with a Q- switched Er:YAG laser at 2.94 micrometer wavelength. The radiant exposure was 500 mJ/cm2. The cornea was cultured on a tissue supporting frame immediately after the ablation. Culture media consisted of 92% minimum essential media, 8% fetal bovine serum, 0.125% HEPES buffer solution, 0.125% gentamicin, and 0.05% fungizone. The entire tissue frame and media container were kept in an incubator at 37 degrees Celsius and 5% CO2. Serial macroscopic photographs of the cultured corneas were taken during the healing process. Histology was performed after 30 days of culture. Results: A clear ablated crater into the stroma was observed immediately after the ablation. The thickness of thermal damage ranges between 1 and 25 micrometer. Haze development within the crater varies from the third day to the fourteenth day according to the depth and the roughness of the crater. Histologic sections of the cultured cornea showed complete re- epithelization of the lased area. Loose fibrous tissue is observed filling the ablated space beneath the epithelium. The endothelium appeared unaffected. Conclusions: The intensity and time of haze development appears dependent upon the depth of the ablation. Cultured human corneas may provide useful information regarding the healing process following laser ablation.

  15. Outcomes of ablative fractional laser scar treatment.

    PubMed

    Kim, Deok-Woo; Hwang, Na-Hyun; Yoon, Eul-Sik; Dhong, Eun-Sang; Park, Seung-Ha

    2015-04-01

    Ablative fractional laser (AFL) systems are commonly used to treat various scars, and recent reports have indicated that early scar treatment with fractional lasers has good aesthetic results. Some scars respond dramatically to AFL treatment, incurring high levels of patient satisfaction; however, other scars respond poorly or became worse after treatment. This study was designed to clarify prognostic factors that predict AFL scar treatment outcomes. A total of 108 patients were included in this study. The fractional laser treatments were repeated every 4 weeks until the scar site was acceptable and no additional improvement was expected or the patient discontinued the treatment. The scar improvements were defined as changes in the Manchester scar scale (MSS) from before to after laser treatment. A digital camera was used to acquire digital photographs of the scars under the same light source, the same background, exposure, and white balance. This study developed a modification of the MSS for image analysis in which colour assessment was based on L*a*b* colour co-ordinates of the digital images. The mean MSS values prior to and after laser treatments were 11.6 ± 3.6 and 9.5 ± 2.9, respectively (p < 0.01). AFL treatment improved the qualities of each scar, and the improvements were evident in colour and contour. Scar elevation, pigmentation, high vascularity, early onset of treatment, and the number of treatment sessions were directly related to scar improvement after AFL therapy (p < 0.05). AFL treatments were effective methods for scar treatment. Clinicians can use these prognostic factors to determine treatment plans and to estimate scar improvement after AFL treatment.

  16. Formation of tribological structures by laser ablation

    NASA Astrophysics Data System (ADS)

    Schilling, Niels; Paschke, Mike; Hendow, Sami T.; Klotzbach, Udo

    2012-03-01

    Many technical applications can benefit from the use of tribological structures in minimizing abrasive material wear and energy consumption without the integration of additional materials in a working assembly. Especially in lubricated friction systems, the tribological character can be significantly improved through the addition of oriented and repetitive microstructure. In this study, experimental tests are discussed for a small range of structure dimensions to verify the effect of optimizing the tribological contact performance. A nanosecond pulsed fiber laser is used to create various test structures with different sizes and form. The quality of the fabricated surface pattern, particularly form correctness, feathering and material modification effects of the ablated area is characterized and optimized. The influence of pulse duration, pulse energy and pulse delay using normal pulsing is presented and compared to various burst modes.

  17. Amalgam ablation with the Er:YAG laser

    NASA Astrophysics Data System (ADS)

    Wigdor, Harvey A.; Visuri, Steven R.; Walsh, Joseph T., Jr.

    1995-04-01

    Any laser that will be used by dentist to replace the dental drill (handpiece) must remove dental hard tissues safely. These lasers must also have the ability to ablate the restorative dental materials which are present in the teeth being treated. Prior to any laser being used to treat humans a thorough knowledge of the effects of the laser treatment on dental materials must be understood. Cores of dental amalgam were created and sliced into thin wafers for this experiment. Ablation efficiency and thermal changes were evaluated with and without water. It appears as if the Er:YAG laser can effectively ablate amalgam dental material with and without water. The water prevents the temperature from increasing much above baseline and does not reduce efficiency of ablation.

  18. Size control of nanoparticles by multiple-pulse laser ablation

    NASA Astrophysics Data System (ADS)

    Yu, Jiaxin; Nan, Junyi; Zeng, Heping

    2017-04-01

    Bare nanoparticles synthesized by laser ablation in water have found their application in catalysis, spectroscopy and biomedical research fields. In this perspective, how to efficiently produce stable nanoparticles with controllable size is an important topic and has attracted a lot of interests. Here, we introduce a multiple-pulse laser as the ablation source. By changing the number of sub-pulses, the average size of nanoparticles can be tuned in a broad range from ∼120 nm to ∼4 nm. The demonstration in this article may offer a new approach to fabricate ultrafine nanostructures and also help the scientific study of the mechanism in laser ablation.

  19. Molecular dynamics simulation of heat-affected zone of copper metal ablated with femtosecond laser

    NASA Astrophysics Data System (ADS)

    Hirayama, Yoichi; Obara, Minoru

    2005-03-01

    Femtosecond laser ablation of materials with high thermal conductivity is of paramount importance, because the chemical composition and properties of the area ablated with femtosecond laser are kept unchanged. The material processing by femtosecond laser can well control the heat-affected zone, compared to nanosecond laser ablation. We report on the heat-affected zone of crystalline copper (Cu) by use of femtosecond laser experimentally and theoretically. Laser ablation of Cu is investigated theoretically by two temperature model and molecular dynamics (MD) simulation. The MD simulation takes into account of electron temperature and thermal diffusion length calculated by two temperature model. The dependence of lattice temperature on time and depth is calculated by the MD simulation and two temperature model. The heat-affected zone estimated from the temperature is mainly studied and calculated to be 3 nm at 0.02 J/cm2 which is below the threshold fluence of 0.137 J/cm2. In addition, the thickness of heat-affected zone of copper crystal ablated with femtosecond Ti:sapphire laser is experimentally studied. As a result of X-ray diffraction (XRD) of the ablated surface, the surface crystallinity is partially changed into disordered structure from crystal form. The residual energy left in the metal, which is not used for ablation, will induce liquid phase, leading to the amorphous phase of the metal during resolidification. The thickness of heat-affected zone depends on laser fluence and is experimentally measured to be less than 1 μm at higher laser fluences than the ablation threshold.

  20. Paint ablation process vs. different laser wavelengths for 18 diverse spray paints used for graffiti on the monuments and historical mansions

    NASA Astrophysics Data System (ADS)

    Daurelio, G.; Comparelli, R.; Catalano, I. M.; Andriani, S. E.

    2010-09-01

    Some diverse spray paints, used for graffiti on the monuments and historical mansions, were selected and chosen. These paints are ones common used by some uncivil young peoples to produce graffiti on many monuments and historical mansions. These paints were sprayed on a stainless steel square plate substrate (30x30mm) and left to dry outdoors for 3 days. Then thickness measurements of each painting on these samples were carried out. Moreover each of the 18 paintings was subjected to reflectivity (absorption) measures by using a reflectance spectra in the range from 2500 to 300 nm. So many plots were recorded by an UV-VIS-NIR Cary 5 (Varian) spectrophotometer using a scanning rate of 600.00 nm / min, a data interval of 1,000 nm and average time of 0.1 s. By using the same technique the restricted range from 300 to 1200nm were investigated for a close, interesting and precise scanning. All this results much more useful and interesting as it can furnish many experimental information on the per cent absorption of a data laser wavelength for a specific spray paint , identified by a RAL (Reichsausschuss für Lieferbedingungen) Code for a normalized colour scales (RAL 840 HR for opaque colours and RAL 841 GL for brilliant colours). This information were not possible to obtain on the scientific literature as well as by some paint manufacturers, so it was necessary and useful to test for a better comprehension of the laser ablation process as well as for the possible chance of success. The works are still in progress.

  1. Nanoparticle fabrication of hydroxyapatite by laser ablation in water

    SciTech Connect

    Musaev, O. R.; Wieliczka, D. M.; Wrobel, J. M.; Kruger, M. B.; Dusevich, V.

    2008-10-15

    Synthetic polycrystalline hydroxyapatite was ablated in water with 337 nm radiation from a UV nitrogen pulsed laser. According to transmission electron microscopy micrographs, the ablated particles were approximately spherical and had a size of {approx}80 nm. Raman spectroscopic analysis demonstrated that particles had the same structure as the original crystal. X-ray photoelectron spectroscopy showed that the surface chemical composition was close to that of the original material. The characteristics of the ablated particles and estimations of the temperature rise of the hydroxyapatite surface under laser irradiation are consistent with the mechanism of explosive boiling being responsible for ablation. The experimental observations offer the basis for preparation of hydroxyapatite nanoparticles by laser ablation in water.

  2. Pulsed Tm:YAG laser ablation of knee joint tissues

    NASA Astrophysics Data System (ADS)

    Shi, Wei-Qiang; Vari, Sandor G.; Duffy, J. T.; Miller, J. M.; Weiss, Andrew B.; Fishbein, Michael C.; Grundfest, Warren S.

    1992-06-01

    We investigated the effect of a free-running 2.01 micron pulsed Tm:YAG laser on bovine knee joint tissues. Ablation rates of fresh fibrocartilage, hyaline cartilage, and bone were measured in saline as a function of laser fluence (160 - 640 J/cm2) and fiber core size (400 and 600 microns). All tissues could be effectively ablated and the ablation rate increased linearly with the increasing fluence. Use of fibers of different core sizes, while maintaining constant energy fluence, did not result in significant difference in ablation rate. Histology analyses of the ablated tissue samples reveal average Tm:YAG radiation induced thermal damage (denatunalization) zones ranging between 130 and 540 microns, depending on the laser parameters and the tissue type.

  3. Laser Ablation with Vacuum Capture for MALDI Mass Spectrometry of Tissue

    NASA Astrophysics Data System (ADS)

    Donnarumma, Fabrizio; Cao, Fan; Murray, Kermit K.

    2016-01-01

    We have developed a laser ablation sampling technique for matrix-assisted laser desorption ionization (MALDI) mass spectrometry and tandem mass spectrometry (MS/MS) analyses of in-situ digested tissue proteins. Infrared laser ablation was used to remove biomolecules from tissue sections for collection by vacuum capture and analysis by MALDI. Ablation and transfer of compounds from tissue removes biomolecules from the tissue and allows further analysis of the collected material to facilitate their identification. Laser ablated material was captured in a vacuum aspirated pipette-tip packed with C18 stationary phase and the captured material was dissolved, eluted, and analyzed by MALDI. Rat brain and lung tissue sections 10 μm thick were processed by in-situ trypsin digestion after lipid and salt removal. The tryptic peptides were ablated with a focused mid-infrared laser, vacuum captured, and eluted with an acetonitrile/water mixture. Eluted components were deposited on a MALDI target and mixed with matrix for mass spectrometry analysis. Initial experiments were conducted with peptide and protein standards for evaluation of transfer efficiency: a transfer efficiency of 16% was obtained using seven different standards. Laser ablation vacuum capture was applied to freshly digested tissue sections and compared with sections processed with conventional MALDI imaging. A greater signal intensity and lower background was observed in comparison with the conventional MALDI analysis. Tandem time-of-flight MALDI mass spectrometry was used for compound identification in the tissue.

  4. Laser Ablation with Vacuum Capture for MALDI Mass Spectrometry of Tissue.

    PubMed

    Donnarumma, Fabrizio; Cao, Fan; Murray, Kermit K

    2016-01-01

    We have developed a laser ablation sampling technique for matrix-assisted laser desorption ionization (MALDI) mass spectrometry and tandem mass spectrometry (MS/MS) analyses of in-situ digested tissue proteins. Infrared laser ablation was used to remove biomolecules from tissue sections for collection by vacuum capture and analysis by MALDI. Ablation and transfer of compounds from tissue removes biomolecules from the tissue and allows further analysis of the collected material to facilitate their identification. Laser ablated material was captured in a vacuum aspirated pipette-tip packed with C18 stationary phase and the captured material was dissolved, eluted, and analyzed by MALDI. Rat brain and lung tissue sections 10 μm thick were processed by in-situ trypsin digestion after lipid and salt removal. The tryptic peptides were ablated with a focused mid-infrared laser, vacuum captured, and eluted with an acetonitrile/water mixture. Eluted components were deposited on a MALDI target and mixed with matrix for mass spectrometry analysis. Initial experiments were conducted with peptide and protein standards for evaluation of transfer efficiency: a transfer efficiency of 16% was obtained using seven different standards. Laser ablation vacuum capture was applied to freshly digested tissue sections and compared with sections processed with conventional MALDI imaging. A greater signal intensity and lower background was observed in comparison with the conventional MALDI analysis. Tandem time-of-flight MALDI mass spectrometry was used for compound identification in the tissue.

  5. Heat accumulation in ultra-short pulsed scanning laser ablation of metals.

    PubMed

    Bauer, Franziska; Michalowski, Andreas; Kiedrowski, Thomas; Nolte, Stefan

    2015-01-26

    High average laser powers can have a serious adverse impact on the ablation quality in ultra-short pulsed laser material processing of metals. With respect to the scanning speed, a sharp transition between a smooth, reflective and an uneven, dark ablated surface is observed. Investigating the influence of the sample temperature, it is experimentally shown that this effect stems from heat accumulation. In a numerical heat flow simulation, the critical scanning speed indicating the change in ablation quality is determined in good agreement with the experimental data.

  6. Osteoid Osteoma: Experience with Laser- and Radiofrequency-Induced Ablation

    SciTech Connect

    Gebauer, Bernhard Tunn, Per-Ulf; Gaffke, Gunnar; Melcher, Ingo; Felix, Roland; Stroszczynski, Christian

    2006-04-15

    The purpose of this study was to analyze the clinical outcome of osteoid osteoma treated by thermal ablation after drill opening. A total of 17 patients and 20 procedures were included. All patients had typical clinical features (age, pain) and a typical radiograph showing a nidus. In 5 cases, additional histological specimens were acquired. After drill opening of the osteoid osteoma nidus, 12 thermal ablations were induced by laser interstitial thermal therapy (LITT) (9F Power-Laser-Set; Somatex, Germany) and 8 ablations by radiofrequency ablation (RFA) (RITA; StarBurst, USA). Initial clinical success with pain relief has been achieved in all patients after the first ablation. Three patients had an osteoid osteoma recurrence after 3, 9, and 10 months and were successfully re-treated by thermal ablation. No major complication and one minor complication (sensible defect) were recorded. Thermal ablation is a safe and minimally invasive therapy option for osteoid osteoma. Although the groups are too small for a comparative analysis, we determined no difference between laser- and radiofrequency-induced ablation in clinical outcome after ablation.

  7. Instabilities and structure formation in laser processing

    SciTech Connect

    Baeuerle, D.; Arenholz, E.; Arnold, N.; Heitz, J.; Kargl, P.B.

    1996-12-31

    This paper gives an overview on different types of instabilities and structure formation in various fields of laser processing. Among the examples discussed in detail are non-coherent structures observed in laser-induced chemical vapor deposition (LCVD), in laser-induced surface modifications, and in laser ablation of polymers.

  8. In situ Diagnostics During Carbon Nanotube Production by Laser Ablation

    NASA Technical Reports Server (NTRS)

    Arepalli, Sivaram

    1999-01-01

    The preliminary results of spectral analysis of the reaction zone during the carbon nanotube production by laser ablation method indicate synergetic dependence on dual laser setup. The emission spectra recorded from different regions of the laser ablated plume at different delay times from the laser pulses are used to map the temperatures of C2 and C3. These are compared with Laser Induced Fluorescence (LIF) spectra also obtained during production to model the growth mechanism of carbon nanotubes. Experiments conducted to correlate the spectral features with nanotube yields as a function of different production parameters will be discussed.

  9. Laser ablation synthesis and spectral characterization of ruby nanoparticles

    NASA Astrophysics Data System (ADS)

    Baranov, M. S.; Bardina, A. A.; Savelyev, A. G.; Khramov, V. N.; Khaydukov, E. V.

    2016-04-01

    The laser ablation method was implemented for synthesis of ruby nanoparticles. Nanoparticles were obtained by nanosecond ablation of bulk ruby crystal in 10% ethanol water solution. The nanoparticles enable water colloid stability and exhibit narrow photoluminescent line at 694 nm when pumped at blue-green spectral range. The ruby nanoparticles were characterized by SEM and Z-sizer.

  10. Ablation layers to prevent pitting in laser peening

    DOEpatents

    Hackel, Lloyd A

    2016-08-09

    A hybrid ablation layer that comprises a separate under layer is applied to a material to prevent pitting resulting from laser peening. The underlayer adheres to the surface of the workpiece to be peened and does not have bubbles and voids that exceed an acceptable size. One or more overlayers are placed over and in contact with the underlayer. Any bubbles formed under the over layers are insulated from the surface to be peened. The process significantly reduces the incidence of pits on peened surfaces.

  11. Laser ablation synthesis of gold nanoparticles in organic solvents.

    PubMed

    Amendola, Vincenzo; Polizzi, Stefano; Meneghetti, Moreno

    2006-04-13

    Free and functionalized gold nanoparticles are synthesized by laser ablation of a gold metal plate immersed in dimethyl sulfoxide, acetonitrile, and tetrahydrofuran. Functionalized gold nanoparticles are synthesized in a one-step process thanks to the solubility of the ligands in these solvents. It is possible to have significant control of the concentration, aggregation, and size of the particles by varying a few parameters. UV-vis spectroscopy and transmission electron microscopy are used for the characterization of the nanoparticles. The Mie model for spherical particles and the Gans model for spheroids allow a fast and reliable interpretation of experimental UV-vis spectra.

  12. Laser tattoo removal with preceding ablative fractional treatment

    NASA Astrophysics Data System (ADS)

    Cencič, Boris; Možina, Janez; Jezeršek, Matija

    2013-06-01

    A combined laser tattoo removal treatment, first the ablative fractional resurfacing (AFR) with an Er:YAG laser and then the q-switched (QSW) Nd:YAG laser treatment, was studied. Experiments show that significantly higher fluences can be used for the same tissue damage levels.

  13. Laser ablation/Fourier transform mass spectrometry of polymers

    NASA Astrophysics Data System (ADS)

    Creasy, William R.; Brenna, J. T.

    1989-10-01

    Laser ablation/ionization followed by Fourier transform mass spectrometry is used to identify and characterize polymers. The mass spectra of several polymers are discussed, including polyimide, polyamic acid, Dupont Tefzel, and polyphenylene sulfide.

  14. Manufacturing of Medical Implants by Combination of Selective Laser Melting and Laser Ablation

    NASA Astrophysics Data System (ADS)

    Hallmann, S.; Glockner, P.; Daniel, C.; Seyda, V.; Emmelmann, C.

    2015-09-01

    The perfect fit of hip stem prostheses is supposed to have positive effects on their lifetime performance. Moreover, the ingrowth of tissue into the surface of the implant has to be assured to create a firm and load bearing contact. For the manufacturing of customized hip stem prostheses, the technology of Selective Laser Melting has shown promising results. Poor surface quality, however, makes it necessary to finish up the part by e.g., sand blasting or polishing. With the use of laser ablation for post-processing, reproducible and functionalized surface morphologies might be achievable. Hence, with the motive to produce customized hip stem prostheses, a combined process chain for both mentioned laser technologies is developed. It is examined what type of surface should be produced at which part of the process chain. The produced implants should contain the demanded final surface characteristics without any conventional post-processing. Slight advantages for the Selective Laser Melting regarding the accuracy for different geometrical structures of 400 μm depth were observed. However, an overall improvement of surface quality after the laser ablation process in terms of osseointegration could be achieved. A complete laser based production of customized hip stem implants is found to be with good prospects.

  15. Ablation of film stacks in solar cell fabrication processes

    DOEpatents

    Harley, Gabriel; Kim, Taeseok; Cousins, Peter John

    2013-04-02

    A dielectric film stack of a solar cell is ablated using a laser. The dielectric film stack includes a layer that is absorptive in a wavelength of operation of the laser source. The laser source, which fires laser pulses at a pulse repetition rate, is configured to ablate the film stack to expose an underlying layer of material. The laser source may be configured to fire a burst of two laser pulses or a single temporally asymmetric laser pulse within a single pulse repetition to achieve complete ablation in a single step.

  16. Femtosecond laser materials processing

    NASA Astrophysics Data System (ADS)

    Banks, Paul S.; Stuart, Brent C.; Komashko, Aleksey M.; Feit, Michael D.; Rubenchik, Alexander M.; Perry, Michael D.

    2000-05-01

    The use of femtosecond lasers allows materials processing of practically any material with extremely high precision and minimal collateral damage. Advantages over conventional laser machining (using pulses longer than a few tens of picoseconds) are realized by depositing the laser energy into the electrons of the material on a time scale short compared to the transfer time of this energy to the bulk of the material, resulting in increased ablation efficiency and negligible shock or thermal stress. The improvement in the morphology by using femtosecond pulses rather than nanosecond pulses has been studied in numerous materials from biological materials to dielectrics to metals. During the drilling process, we have observed the onset of small channels which drill faster than the surrounding material.

  17. Femtosecond Laser Materials Processing

    SciTech Connect

    Banks, P.S.; Stuart, B.C.; Komashko, A.M.; Feit, M.D.; Rubenchik, A.M.; Perry, M.D.

    2000-03-06

    The use of femtosecond lasers allows materials processing of practically any material with extremely high precision and minimal collateral damage. Advantages over conventional laser machining (using pulses longer than a few tens of picoseconds) are realized by depositing the laser energy into the electrons of the material on a time scale short compared to the transfer time of this energy to the bulk of the material, resulting in increased ablation efficiency and negligible shock or thermal stress. The improvement in the morphology by using femtosecond pulses rather than nanosecond pulses has been studied in numerous materials from biologic materials to dielectrics to metals. During the drilling process, we have observed the onset of small channels which drill faster than the surrounding material.

  18. Laser ablation for the synthesis of carbon nanotubes

    NASA Technical Reports Server (NTRS)

    Holloway, Brian C. (Inventor); Eklund, Peter C. (Inventor); Smith, Michael W. (Inventor); Jordan, Kevin C. (Inventor); Shinn, Michelle (Inventor)

    2012-01-01

    Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces and output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of "side pumped", preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

  19. Laser ablation for the synthesis of carbon nanotubes

    NASA Technical Reports Server (NTRS)

    Holloway, Brian C. (Inventor); Eklund, Peter C. (Inventor); Smith, Michael W. (Inventor); Jordan, Kevin C. (Inventor); Shinn, Michelle (Inventor)

    2010-01-01

    Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces an output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of side pumped, preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

  20. Laser ablation for the synthesis of carbon nanotubes

    DOEpatents

    Holloway, Brian C.; Eklund, Peter C.; Smith, Michael W.; Jordan, Kevin C.; Shinn, Michelle

    2010-04-06

    Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces an output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of "side pumped", preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

  1. Laser ablation for the synthesis of carbon nanotubes

    DOEpatents

    Holloway, Brian C; Eklund, Peter C; Smith, Michael W; Jordan, Kevin C; Shinn, Michelle

    2012-11-27

    Single walled carbon nanotubes are produced in a novel apparatus by the laser-induced ablation of moving carbon target. The laser used is of high average power and ultra-fast pulsing. According to various preferred embodiments, the laser produces and output above about 50 watts/cm.sup.2 at a repetition rate above about 15 MHz and exhibits a pulse duration below about 10 picoseconds. The carbon, carbon/catalyst target and the laser beam are moved relative to one another and a focused flow of "side pumped", preheated inert gas is introduced near the point of ablation to minimize or eliminate interference by the ablated plume by removal of the plume and introduction of new target area for incidence with the laser beam. When the target is moved relative to the laser beam, rotational or translational movement may be imparted thereto, but rotation of the target is preferred.

  2. Carbon nanocrystals produced by pulsed laser ablation of carbon

    NASA Astrophysics Data System (ADS)

    Mangione, A.; Torrisi, L.; Picciotto, A.; Caridi, F.; Margarone, D.; Fazio, E.; La Mantia, A.; di Marco, G.

    2005-10-01

    Plasma laser ablation experiments were performed irradiating glassy-carbon targets placed in vacuum through a pulsed Nd:YAG laser operating at the second harmonic (532 nm), 9 ns pulse width and 10(9) W/cm(2) density power. Thin films of ablated carbon were deposited on silicon oxide substrates placed at different distances and angles with respect to the target. The analysis of the deposited material was carried out by using surface profiler, scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) and Raman spectroscopy. Results show the evidence of carbon nanocrystals and nanostructures with dimension of the order of 100 nm deposited on the substrates together with a large amount of amorphous phase. The spectroscopic investigations and the SEM images indicate the formation of nanodiamond seeds as a nucleation process induced on the substrate surface. Nanostructures were investigated as a function of the laser intensity and angle distribution. Experimental results were compared with the literature data coming from nanodiamonds growth with different techniques. Experiments performed at Instituto Nazionale di Fisica Nucleare-Laboratori Nazionali del Sud (INFN-LNS) of Catania (Italy) and data analysis conducted at Dipartimento di Fisica and DFMTA of the Universita of Messina (Italy), CNR-ITIS of Messina and ST-Microelectronics of Catania will be presented and discussed.

  3. Simulation of femtosecond pulsed laser ablation of metals

    NASA Astrophysics Data System (ADS)

    Davydov, R. V.; Antonov, V. I.

    2016-11-01

    In this paper a mathematical model for femtosecond laser ablation of metals is proposed, based on standard two-temperature model connected with 1D hydrodynamic equations. Wide-range equation of state has been developed. The simulation results are compared with experimental data for aluminium and copper. A good agreement for both metals with numerical results and experiment shows that this model can be employed for choosing laser parameters to better accuracy in nanoparticles production by ablation of metals.

  4. Momentum Transfer by Laser Ablation of Irregularly Shaped Space Debris

    SciTech Connect

    Liedahl, Duane A.; Libby, Stephen B.; Rubenchik, Alexander

    2010-10-08

    Proposals for ground-based laser remediation of space debris rely on the creation of appropriately directed ablation-driven impulses to either divert the fragment or drive it into an orbit with a perigee allowing atmospheric capture. For a spherical fragment, the ablation impulse is a function of the orbital parameters and the laser engagement angle. If, however, the target is irregularly shaped and arbitrarily oriented, new impulse effects come into play. Here we present an analysis of some of these effects.

  5. Momentum Transfer by Laser Ablation of Irregularly Shaped Space Debris

    SciTech Connect

    Liedahl, D A; Libby, S B; Rubenchik, A

    2010-02-04

    Proposals for ground-based laser remediation of space debris rely on the creation of appropriately directed ablation-driven impulses to either divert the fragment or drive it into an orbit with a perigee allowing atmospheric capture. For a spherical fragment, the ablation impulse is a function of the orbital parameters and the laser engagement angle. If, however, the target is irregularly shaped and arbitrarily oriented, new impulse effects come into play. Here we present an analysis of some of these effects.

  6. Ultra-fast movies of thin-film laser ablation

    NASA Astrophysics Data System (ADS)

    Domke, Matthias; Rapp, Stephan; Schmidt, Michael; Huber, Heinz P.

    2012-11-01

    Ultra-short-pulse laser irradiation of thin molybdenum films from the glass substrate side initiates an intact Mo disk lift off free from thermal effects. For the investigation of the underlying physical effects, ultra-fast pump-probe microscopy is used to produce stop-motion movies of the single-pulse ablation process, initiated by a 660-fs laser pulse. The ultra-fast dynamics in the femtosecond and picosecond ranges are captured by stroboscopic illumination of the sample with an optically delayed probe pulse of 510-fs duration. The nanosecond and microsecond delay ranges of the probe pulse are covered by an electronically triggered 600-ps laser. Thus, the setup enables an observation of general laser ablation processes from the femtosecond delay range up to the final state. A comparison of time- and space-resolved observations of film and glass substrate side irradiation of a 470-nm molybdenum layer reveals the driving mechanisms of the Mo disk lift off initiated by glass-side irradiation. Observations suggest that a phase explosion generates a liquid-gas mixture in the molybdenum/glass interface about 10 ps after the impact of the pump laser pulse. Then, a shock wave and gas expansion cause the molybdenum layer to bulge, while the enclosed liquid-gas mixture cools and condenses at delay times in the 100-ps range. The bulging continues for approximately 20 ns, when an intact Mo disk shears and lifts off at a velocity of above 70 m/s. As a result, the remaining hole is free from thermal effects.

  7. Photoactive dye enhanced tissue ablation for endoscopic laser prostatectomy

    NASA Astrophysics Data System (ADS)

    Ahn, Minwoo; Nguyen, Trung Hau; Nguyen, Van Phuc; Oh, Junghwan; Kang, Hyun Wook

    2015-02-01

    Laser light has been widely used as a surgical tool to treat benign prostate hyperplasia with high laser power. The purpose of this study was to validate the feasibility of photoactive dye injection to enhance light absorption and eventually to facilitate tissue ablation with low laser power. The experiment was implemented on chicken breast due to minimal optical absorption Amaranth (AR), black dye (BD), hemoglobin powder (HP), and endoscopic marker (EM), were selected and tested in vitro with a customized 532-nm laser system with radiant exposure ranging from 0.9 to 3.9 J/cm2. Light absorbance and ablation threshold were measured with UV-VIS spectrometer and Probit analysis, respectively, and compared to feature the function of the injected dyes. Ablation performance with dye-injection was evaluated in light of radiant exposure, dye concentration, and number of injection. Higher light absorption by injected dyes led to lower ablation threshold as well as more efficient tissue removal in the order of AR, BD, HP, and EM. Regardless of the injected dyes, ablation efficiency principally increased with input parameter. Among the dyes, AR created the highest ablation rate of 44.2+/-0.2 μm/pulse due to higher absorbance and lower ablation threshold. Preliminary tests on canine prostate with a hydraulic injection system demonstrated that 80 W with dye injection yielded comparable ablation efficiency to 120 W with no injection, indicating 33 % reduced laser power with almost equivalent performance. In-depth comprehension on photoactive dye-enhanced tissue ablation can help accomplish efficient and safe laser treatment for BPH with low power application.

  8. High Current Cathodes Fabricated by KrF Laser Ablation

    SciTech Connect

    Gilgenbach, Ronald M.; Lau, Y. Y.; Jones, M. C.; Johnston, M. D.; Jordan, N. M.; Hoff, B. W.

    2010-10-08

    In this paper we review several high power laser ablation techniques that have been utilized to fabricate high current (1-80 kA) electron beam cathodes for accelerators and microwave sources: 1) Projection Ablation Lithography (PAL) cathodes, 2) Ablation Line Focus (ALF) cathodes, and 3) Metal-Oxide-Junction (MOJ) cathodes. Laser-ablative micromachining techniques (PAL and ALF) have been utilized to generate micron-scale features on metal substrates that provide electric field (beta) enhancement for Fowler-Nordheim emission and plasma cathodes. Since these laser-ablated patterns are directly, laser-written on the substrate metal they exhibit much higher thermal conductivity for higher current capability and increased damage thresholds. Metal-Oxide-Junction (MOJ) cathodes exploit the triple-point electron emission that occurs at the interface between metal, insulator and vacuum.The ablation laser is a KrF excimer laser with a pulse energy of 600 mJ and pulselength of 20 ns. Cathode experiments were performed on the MELBA-C accelerator: V = -300 kV, pulselength = 0.5 microsecond. Data will be presented for PAL, ALF and MOJ cathodes.

  9. Tissue morphologic analysis and ablation rates in the UV and visible for laser angioplasty

    NASA Astrophysics Data System (ADS)

    Sartori, M.; Henry, P. D.; Roberts, R.; Sauerbrey, R.; Tittel, F. K.

    1986-08-01

    Ablation rates were determined in human and canine aortas subjected to excimer and visible laser radiation. For UV and pulsed frequency doubled Nd:YAG lasers ablation rates were constant and depended linearly on average laser power, while for cw argon lasers ablation rates depended nonlinearly on laser power.

  10. Deposition of epitaxial Cu 2O films on (100) MgO by laser ablation and their processing using ion beams

    NASA Astrophysics Data System (ADS)

    Ogale, S. B.; Bilurkar, P. G.; Mate, Nitant; Parikh, Nalin; Patnaik, B.

    1993-03-01

    Epitaxial thin films of Cu2O have been deposited on (100) MgO substrates by pulsed excimer laser ablation technique. Chemical polishing of the substrates by etching them in hot phosphoric acid prior to film deposition is found to be a critical step in realizing epitaxy. A KrF excimer laser operating at 248 nm wavelengths was used for ablation. The depositions were carried out at the laser energy density of 2 J/cm2 and the pulse repetition rate of 5 Hz. The substrate temperature was held at 700°C and the oxygen partial pressure during deposition and cooling was 10-3 Torr. The epitaxial nature of the deposited films was established via X-ray diffraction (XRD) and Rutherford back-scattering (RBS) channelling measurements. The epitaxial films thus obtained were then subjected to ion bombardment for studies of damage formation. Implantations were carried out using 110 keV Ar+ ions over a dose range between 5 x 1014 and 1.5 x 1016 ions/cmz. The as-grown and implanted samples were subjected to resistivity versus temperature measurements in view of the importance of the Cu-O system in the context of the phenomenon of high temperature superconductivity.

  11. Synthesis of CaWO4 nanocolloidal suspension via pulsed laser ablation and its optical properties

    NASA Astrophysics Data System (ADS)

    Ryu, Jeong Ho; Park, Gyeong Seon; Kim, Kang Min; Lim, Chang Sung; Yoon, Jong-Won; Shim, Kwang Bo

    2007-09-01

    Pulsed laser ablation (PLA) in the liquid phase was successfully employed to synthesize calcium tungstate (CaWO4) nanocolloidal suspension. The crystalline phase, particle morphology and laser ablation mechanism for the colloidal nanoparticles were investigated using XRD, TEM and SEM. The obtained colloidal suspension consisted of well-dispersed CaWO4 nanoparticles which showed a spherical shape with sizes ranging from 5 to 30 nm. The laser ablation and the nanoparticle forming process were discussed under consideration of the photo-ablation mechanism, where the nanoparticles were generated by rapid condensation of the plume in high pressured ethanol vapor. The optical properties of the prepared CaWO4 colloidal nanoparticles were analyzed in detail using XPS, Raman spectroscopy, UV-Vis spectroscopy and PL spectrophotometry. The optical band gap was estimated by Tauc and Menths law.

  12. Analysis of laser ablation dynamics of CFRP in order to reduce heat affected zone

    NASA Astrophysics Data System (ADS)

    Sato, Yuji; Tsukamoto, Masahiro; Nariyama, Tatsuya; Nakai, Kazuki; Matsuoka, Fumihiro; Takahashi, Kenjiro; Masuno, Shinichiro; Ohkubo, Tomomasa; Nakano, Hitoshi

    2014-03-01

    A carbon fiber reinforced plastic [CFRP], which has high strength, light weight and weather resistance, is attractive material applied for automobile, aircraft and so on. The laser processing of CFRP is one of suitable way to machining tool. However, thermal affected zone was formed at the exposure part, since the heat conduction property of the matrix is different from that of carbon fiber. In this paper, we demonstrated that the CFRP plates were cut with UV nanosecond laser to reduce the heat affected zone. The ablation plume and ablation mass were investigated by laser microscope and ultra-high speed camera. Furthermore, the ablation model was constructed by energy balance, and it was confirmed that the ablation rate was 0.028 μg/ pulse in good agreement with the calculation value of 0.03 μg/ pulse.

  13. Dynamics of Laser Ablation in Superfluid ^4{He}

    NASA Astrophysics Data System (ADS)

    Buelna, X.; Popov, E.; Eloranta, J.

    2017-02-01

    Pulsed laser ablation of metal targets immersed in superfluid ^4{He} is visualized by time-resolved shadowgraph photography and the products are analyzed by post-experiment atomic force microscopy (AFM) measurements. The expansion dynamics of the gaseous ablation half-bubble on the target surface appears underdamped and follows the predicted behavior for the thermally induced bubble growth mechanism. An inherent instability of the ablation bubble appears near its maximum radius and no tightly focused cavity collapse or rebound events are observed. During the ablation bubble retreat phase, the presence of sharp edges in the target introduces flow patterns that lead to the creation of large classical vortex rings. Furthermore, on the nanometer scale, AFM data reveal that the metal nanoparticles created by laser ablation are trapped in spherical vortex tangles and quantized vortex rings present in the non-equilibrium liquid.

  14. Far-ultraviolet laser ablation of the cornea: photoacoustic studies

    SciTech Connect

    Srinivasan, R.; Dyer, P.E.; Braren, B.

    1987-01-01

    Wide bandwidth piezoelectric transducers made of thin (9 microns) polyvinylidene fluoride film have been used to make time-resolved measurements of the stress-wave generated by far-ultraviolet (193 nm) laser ablation in corneal tissue in vitro. At high fluence (approximately 250 mJ/cm2), ablation commences within 10 ns (+/- 5 ns) of the laser pulse and generates short acoustic impulses (approximately 30 ns). The time profile of the ablation, when coupled to the energy requirements for ablation from earlier work, allows the estimation of a temperature and a half-life for the thermal decomposition of the collagen in cornea. These values do not support a photothermal mechanism for the ablation under the experimental conditions.

  15. Laser ablation of a turbid medium: Modeling and experimental results

    SciTech Connect

    Brygo, F.; Semerok, A.; Weulersse, J.-M.; Thro, P.-Y.; Oltra, R.

    2006-08-01

    Q-switched Nd:YAG laser ablation of a turbid medium (paint) is studied. The optical properties (absorption coefficient, scattering coefficient, and its anisotropy) of a paint are determined with a multiple scattering model (three-flux model), and from measurements of reflection-transmission of light through thin layers. The energy deposition profiles are calculated at wavelengths of 532 nm and 1.064 {mu}m. They are different from those described by a Lambert-Beer law. In particular, the energy deposition of the laser beam is not maximum on the surface but at some depth inside the medium. The ablated rate was measured for the two wavelengths and compared with the energy deposition profile predicted by the model. This allows us to understand the evolution of the ablated depth with the wavelength: the more the scattering coefficient is higher, the more the ablated depth and the threshold fluence of ablation decrease.

  16. Laser ablation with applied magnetic field for electric propulsion

    NASA Astrophysics Data System (ADS)

    Batishcheva, Alla; Batishchev, Oleg; Cambier, Jean-Luc

    2012-10-01

    Using ultrafast lasers with tera-watt-level power allows efficient ablation and ionization of solid-density materials [1], creating dense and hot (˜100eV) plasma. We propose ablating small droplets in the magnetic nozzle configurations similar to mini-helicon plasma source [2]. Such approach may improve the momentum coupling compared to ablation of solid surfaces and facilitate plasma detachment. Results of 2D modeling of solid wire ablation in the applied magnetic field are presented and discussed. [4pt] [1] O. Batishchev et al, Ultrafast Laser Ablation for Space Propulsion, AIAA technical paper 2008-5294, -16p, 44th JPC, Hartford, 2008.[0pt] [2] O. Batishchev and J.L. Cambier, Experimental Study of the Mini-Helicon Thruster, Air Force Research Laboratory Report, AFRL-RZ-ED-TR-2009-0020, 2009.

  17. Control of laser-ablation plasma potential with external electrodes

    SciTech Connect

    Isono, Fumika Nakajima, Mitsuo; Hasegawa, Jun; Kawamura, Tohru; Horioka, Kazuhiko

    2015-08-15

    The potential of a laser-ablation plasma was controlled stably up to +2 kV by using external ring electrodes. A stable electron sheath was formed between the plasma and the external electrodes by placing the ring electrodes away from the boundary of the drifting plasma. The plasma kept the potential for a few μs regardless of the flux change of the ablation plasma. We also found that the plasma potential changed with the expansion angle of the plasma from the target. By changing the distance between the plasma boundary and the external electrodes, we succeeded in controlling the potential of laser-ablation plasma.

  18. Peak pressures and temperatures within laser-ablated tissues

    NASA Astrophysics Data System (ADS)

    Furzikov, Nickolay P.; Dmitriev, A. C.; Lekhtsier, Eugeny N.; Orlov, M. Y.; Semyenov, Alexander D.; Tyurin, Vladimir S.

    1991-06-01

    The time-of-flight probing of supersonic motion of ablation products or preceding shock wave was used to extract the maximum values of initial pressure and temperature. Measurements were accomplished at three laser- tissue combinations - the TEA CO2 laser plus artery wall, and the ArF excimer laser or the Q-switched Er:YSGG laser plus pig eye cornea and gave pressures from 1 to 40 MPa and temperatures from 450 to 700 K. These data favor the thermal ablation mechanism for all three cases.

  19. Derivation of effective penetration depth of femtosecond laser pulses in metal from ablation rate dependence on laser fluence, incidence angle, and polarization

    SciTech Connect

    Miyasaka, Yasuhiro; Hashida, Masaki; Nishii, Takaya; Inoue, Shunsuke; Sakabe, Shuji

    2015-01-05

    Ablation rate dependence on laser fluence for copper subjected to oblique femtosecond laser irradiation has been determined experimentally in order to investigate processing induced by oblique irradiation. A difference of ablation rate between p-polarized and s-polarized oblique irradiation is clearly observed. Effective penetration depth is defined to explain the ablation rate dependence instead of using optical penetration depth, which is treated as a key value for determining the ablation rate in conventional theory. The effective penetration depth for copper is presented in simple formulas as a function of laser incidence angle for each polarization.

  20. Subpicosecond and picosecond laser ablation of dental enamel: comparative analysis

    NASA Astrophysics Data System (ADS)

    Rode, Andrei V.; Madsen, Nathan R.; Kolev, Vesselin Z.; Gamaly, Eugene G.; Luther-Davies, Barry; Dawes, Judith M.; Chan, A.

    2004-06-01

    We report the use of sub-picosecond near-IR and ps UV pulsed lasers for precision ablation of freshly extracted human teeth. The sub-picosecond laser wavelength was ~800nm, with pulsewidth 150 fs and pulse repetition rate of 1kHz; the UV laser produced 10 ps pulses at 266 nm with pulse rate of ~1.2x105 pulses/s; both lasers produced ~1 W of output energy, and the laser fluence was kept at the same level of 10-25 J/cm2. Laser radiation from both laser were effectively absorbed in the teeth enamel, but the mechanisms of absorption were radically different: the near-IR laser energy was absorbed in a plasma layer formed through the optical breakdown mechanism initiated by multiphoton absorption, while the UV-radiation was absorbed due to molecular photodissociation of the enamel and conventional thermal deposition. The rise in the intrapulpal temperature was monitored by embedded thermocouples, and was shown to remain low with subpicosecond laser pulses, but risen up to 30°C, well above the 5°C pain level with the UV-laser. This study demonstrates the potential for ultra-short-pulsed lasers to precision and painless ablation of dental enamel, and indicated the optimal combination of laser parameters in terms of pulse energy, duration, intensity, and repetition rate, required for the laser ablation rates comparable to that of mechanical drill.

  1. Transmission of 1064 nm laser radiation during ablation with an ultra-short pulse laser (USPL) system

    NASA Astrophysics Data System (ADS)

    Schelle, Florian; Meister, Jörg; Oehme, Bernd; Frentzen, Matthias

    2012-01-01

    During ablation of oral hard tissue with an USPL system a small amount of the incident laser power does not contribute to the ablation process and is being transmitted. Partial transmission of ultra-short laser pulses could potentially affect the dental pulp. The aim of this study was to assess the transmission during ablation and to deduce possible risks for the patient. The study was performed with an Nd:YVO4 laser, emitting pulses with a duration of 8 ps at a wavelength of 1064 nm. A repetition rate of 500 kHz and an average power of 9 W were chosen to achieve high ablation efficiency. A scanner system created square cavities with an edge length of 1 mm. Transmission during ablation of mammoth ivory and dentin slices with a thickness of 2 mm and 5 mm was measured with a power meter, placed directly beyond the samples. Effects on subjacent blood were observed by ablating specimens placed in contact to pork blood. In a separate measurement the temperature increase during ablation was monitored using an infrared camera. The influence of transmission was assessed by tuning down the laser to the corresponding power and then directly irradiating the blood. Transmission during ablation of 2 mm specimens was about 7.7% (ivory) and 9.6% (dentin) of the incident laser power. Ablation of specimens directly in contact to blood caused coagulation at longer irradiation times (t~18s). Direct irradiation of blood with the transmitted power provoked bubbling and smoke formation. Temperature measurements identified heat generation as the main reason for the observed coagulation.

  2. MRI-guided laser ablation of neuroendocrine tumor hepatic metastases

    PubMed Central

    Perälä, Jukka; Klemola, Rauli; Kallio, Raija; Li, Chengli; Vihriälä, Ilkka; Salmela, Pasi I; Tervonen, Osmo

    2014-01-01

    Background Neuroendocrine tumors (NET) represent a therapeutically challenging and heterogeneous group of malignancies occurring throughout the body, but mainly in the gastrointestinal system. Purpose To describe magnetic resonance imaging (MRI)-guided laser ablation of NET liver metastases and assess its role within the current treatment options and methods. Material and Methods Two patients with NET tumor hepatic metastases were treated with MRI-guided interstitial laser ablation (LITT). Three tumors were treated. Clinical follow-up time was 10 years. Results Both patients were successfully treated. There were no local recurrences at the ablation site during the follow-up. Both patients had survived at 10-year follow-up. One patient is disease-free. Conclusion MRI-guided laser ablation can be used to treat NET tumor liver metastases but combination therapy and a rigorous follow-up schedule are recommended. PMID:24778794

  3. Planarization of Isolated Defects on ICF Target Capsule Surfaces by Pulsed Laser Ablation

    SciTech Connect

    Alfonso, Noel; Carlson, Lane C.; Bunn, Thomas L.

    2016-08-09

    Demanding surface quality requirements for inertial confinement fusion (ICF) capsules motivated the development of a pulsed laser ablation method to reduce or eliminate undesirable surface defects. The pulsed laser ablation technique takes advantage of a full surface (4π) capsule manipulation system working in combination with an optical profiling (confocal) microscope. Based on the defect topography, the material removal rate, the laser pulse energy and its beam profile, a customized laser raster pattern is derived to remove the defect. The pattern is a table of coordinates and number of pulses that dictate how the defect will be vaporized until its height is level with the capsule surface. This paper explains how the raster patterns are optimized to minimize surface roughness and how surface roughness after laser ablation is simulated. The simulated surfaces are compared with actual ablated surfaces. Large defects are reduced to a size regime where a tumble finishing process produces very high quality surfaces devoid of high mode defects. The combined polishing processes of laser ablation and tumble finishing have become routine fabrication steps for National Ignition Facility capsule production.

  4. Planarization of Isolated Defects on ICF Target Capsule Surfaces by Pulsed Laser Ablation

    DOE PAGES

    Alfonso, Noel; Carlson, Lane C.; Bunn, Thomas L.

    2016-08-09

    Demanding surface quality requirements for inertial confinement fusion (ICF) capsules motivated the development of a pulsed laser ablation method to reduce or eliminate undesirable surface defects. The pulsed laser ablation technique takes advantage of a full surface (4π) capsule manipulation system working in combination with an optical profiling (confocal) microscope. Based on the defect topography, the material removal rate, the laser pulse energy and its beam profile, a customized laser raster pattern is derived to remove the defect. The pattern is a table of coordinates and number of pulses that dictate how the defect will be vaporized until its heightmore » is level with the capsule surface. This paper explains how the raster patterns are optimized to minimize surface roughness and how surface roughness after laser ablation is simulated. The simulated surfaces are compared with actual ablated surfaces. Large defects are reduced to a size regime where a tumble finishing process produces very high quality surfaces devoid of high mode defects. The combined polishing processes of laser ablation and tumble finishing have become routine fabrication steps for National Ignition Facility capsule production.« less

  5. Efficient space propulsion engines based on laser ablation

    SciTech Connect

    Phipps, C.R.

    1993-08-01

    Recent results have shown laser momentum transfer coefficients C{sub m} as large as 700 dynes/J from visible and near-infrared laser pulses with heterogeneous targets. Using inexpensive target materials, it is now possible to deliver a 1-tonne satellite from LEO to GEO in 21 days using a 10-kW onboard laser ablation engine, or to maintain several 1-tonne GEO satellites on station from Earth indefinitely using a laser with 100-W average power.

  6. Laser-induced breakdown spectroscopy for on-line control of selective removal of cobalt binder from tungsten carbide hardmetal by pulsed UV laser surface ablation

    NASA Astrophysics Data System (ADS)

    Li, Tiejun; Lou, Qihong; Wei, Yunrong; Huang, Feng; Dong, Jingxing; Liu, Jingru

    2001-09-01

    Laser-induced breakdown spectroscopy (LIBS) was successfully used in on-line control of selective removal of cobalt from tungsten carbide hardmetal by pulsed UV laser surface ablation. The dependence of LIBS on number of laser shots was investigated at different laser fluences. The optimal laser fluence of 2.5 J/cm 2 suited for selective removal of cobalt from surface layer of hardmetal was confirmed. The result sample was also subject to different post-examinations to evaluate the feasibility of the application of LIBS in this laser ablation process. It was demonstrated that, monitoring of the emission intensity of cobalt lines could be used as a control parameter for selective removal of cobalt from surface layer of hardmetal by pulsed UV laser. The on-line implementation of the spectroscopic technique LIBS to the surface-ablation process provided important information about the optimal-ablation parameters.

  7. Modeling of long term behavior of ablation plumes produced with ultrashort laser pulses

    SciTech Connect

    Feit, M D; Komashko, A M; Rubenchik, A M

    2000-02-10

    Expansion of ablation plumes created by intense ultrashort lasers is determined by various complicated physical processes which have very different spatial and time scales. Since complete simulation by one model is practically impossible, the authors suggest using two models describing initial and final stages that can be matched at an intermediate time. The proposed modeling procedure connects laser parameters to plume properties far away from the ablation spot. Laser material interaction and beginning of the expansion are simulated with a one-dimensional hydrodynamics code and the final stage is modeled using an analytical solution for an expanding three-dimensional ellipsoidal gas cloud.

  8. Destruction of monocrystalline silicon with nanosecond pulsed fiber laser accompanied by the oxidation of ablation microparticles

    NASA Astrophysics Data System (ADS)

    Veiko, V. P.; Skvortsov, A. M.; Huynh, C. T.; Petrov, A. A.

    2013-11-01

    In this work, we report an observation of process of local destruction monocrystalline silicon with a scanning beam irradiation of pulse ytterbium fiber laser with a wavelength λ= 1062 nm, accompanied by the oxidation of ablation microparticles. It is shown that depending on the power density of irradiation was observed a large scatter size of the microparticles. From a certain average power density is observed beginning oxidation particulate emitted from the surface of the irradiated area. By varying the parameters of the laser beam such as scanning speed, pulse repetition rate, overlap of laser spot, radiation dose can be achieved almost complete oxidation of all formed during the ablation of microparticles.

  9. Ultrashort laser ablation of PMMA and intraocular lenses

    NASA Astrophysics Data System (ADS)

    Serafetinides, A. A.; Makropoulou, M.; Fabrikesi, E.; Spyratou, E.; Bacharis, C.; Thomson, R. R.; Kar, A. K.

    2008-10-01

    The use of intraocular lenses (IOLs) is the most promising method to restore vision after cataract surgery. Several new materials, techniques, and patterns have been studied for forming and etching IOLs to improve their optical properties and reduce diffractive aberrations. This study is aimed at investigating the use of ultrashort laser pulses to ablate the surface of PMMA and intraocular lenses, and thus provide an alternative to conventional techniques. Ablation experiments were conducted using various polymer substrates (PMMA samples, hydrophobic acrylic IOL, yellow azo dye doped IOL, and hydrophilic acrylic IOL consist of 25% H2O). The irradiation was performed using 100 fs pulses of 800 nm radiation from a regeneratively amplified Ti:sapphire laser system. We investigated the ablation efficiency and the phenomenology of the ablated patterns by probing the ablation depth using a profilometer. The surface modification was examined using a high resolution optical microscope (IOLs) or atomic force microscope—AFM (PMMA samples). It was found that different polymers exhibited different ablation characteristics, a result that we attribute to the differing optical properties of the materials. In particular, it was observed that the topography of the ablation tracks created on the hydrophilic intraocular lenses was smoother in comparison to those created on the PMMA and hydrophobic lens. The yellow doped hydrophobic intraocular lenses show higher ablation efficiency than undoped hydrophobic acrylic lenses.

  10. Ultrafast laser ablation for targeted atherosclerotic plaque removal

    NASA Astrophysics Data System (ADS)

    Lanvin, Thomas; Conkey, Donald B.; Descloux, Laurent; Frobert, Aurelien; Valentin, Jeremy; Goy, Jean-Jacques; Cook, Stéphane; Giraud, Marie-Noelle; Psaltis, Demetri

    2015-07-01

    Coronary artery disease, the main cause of heart disease, develops as immune cells and lipids accumulate into plaques within the coronary arterial wall. As a plaque grows, the tissue layer (fibrous cap) separating it from the blood flow becomes thinner and increasingly susceptible to rupturing and causing a potentially lethal thrombosis. The stabilization and/or treatment of atherosclerotic plaque is required to prevent rupturing and remains an unsolved medical problem. Here we show for the first time targeted, subsurface ablation of atherosclerotic plaque using ultrafast laser pulses. Excised atherosclerotic mouse aortas were ablated with ultrafast near-infrared (NIR) laser pulses. The physical damage was characterized with histological sections of the ablated atherosclerotic arteries from six different mice. The ultrafast ablation system was integrated with optical coherence tomography (OCT) imaging for plaque-specific targeting and monitoring of the resulting ablation volume. We find that ultrafast ablation of plaque just below the surface is possible without causing damage to the fibrous cap, which indicates the potential use of ultrafast ablation for subsurface atherosclerotic plaque removal. We further demonstrate ex vivo subsurface ablation of a plaque volume through a catheter device with the high-energy ultrafast pulse delivered via hollow-core photonic crystal fiber.

  11. Doping He droplets by laser ablation with a pulsed supersonic jet source

    SciTech Connect

    Katzy, R.; Singer, M.; Izadnia, S.; LaForge, A. C. Stienkemeier, F.

    2016-01-15

    Laser ablation offers the possibility to study a rich number of atoms, molecules, and clusters in the gas phase. By attaching laser ablated materials to helium nanodroplets, one can gain highly resolved spectra of isolated species in a cold, weakly perturbed system. Here, we present a new setup for doping pulsed helium nanodroplet beams by means of laser ablation. In comparison to more well-established techniques using a continuous nozzle, pulsed nozzles show significant differences in the doping efficiency depending on certain experimental parameters (e.g., position of the ablation plume with respect to the droplet formation, nozzle design, and expansion conditions). In particular, we demonstrate that when the ablation region overlaps with the droplet formation region, one also creates a supersonic beam of helium atoms seeded with the sample material. The processes are characterized using a surface ionization detector. The overall doping signal is compared to that of conventional oven cell doping showing very similar dependence on helium stagnation conditions, indicating a comparable doping process. Finally, the ablated material was spectroscopically studied via laser induced fluorescence.

  12. Laser ablation threshold and etch rate comparison between the ultrafast Yb fiber-based FCPA laser and a Ti:sapphire laser for various materials

    NASA Astrophysics Data System (ADS)

    Bovatsek, James M.; Shah, Lawrence; Arai, Alan Y.; Uehara, Yuzuru

    2004-10-01

    Ti:Sapphire lasers remain the most widely used utlrafast laser. However, precise optical alignment and environmental control are necessary for continuous, long-term stable operatoin of the laser. IMRA's FCPA laser is an air-cooled, Yb fiber-based ultrafast laser designed to operate in an industrial environment and provide a stable, high-quality laser beam. In this work, the micromachining performance of the FCPA laser is directly compared with a conventional Ti:Sapphire regenerative amplifier laser. An experimental study was conducted to determine the ablation threshold and etch rate for a variety of materials (including metals, semiconductors, and dielectrics). The materials chosen for the experiments cover a wide range of optical, mechanical and physical properties. Similar focusing conditions were used for both lasers in order to ensure that any differences in the results are primarily due to the different characteristics of each laser. For materials with a relatively low ablation threshold, the full energy of the Ti:Sapphire laser is not needed. Furthermore, it is near the ablation threshold where ultrafast laser processing provides the benefit of minimal thermal damage to the surrounding material. Although the relatively low pulse energy of the FCPA limits its ability to ablate some harder materials, its high repetition rate increases the material processing speed and its good beam quality and stability facilitates tight, efficient focusing for precise machining of small features.

  13. Material morphological characteristics in laser ablation of alpha case from titanium alloy

    NASA Astrophysics Data System (ADS)

    Yue, Liyang; Wang, Zengbo; Li, Lin

    2012-08-01

    Alpha case (an oxygen enriched alloy layer) is commonly formed in forged titanium alloys during the manufacturing process and it reduces the service life of the materials. This layer is normally removed mechanically or chemically. This paper reports the feasibility and characteristics of using a short pulsed laser to remove oxygen-enriched alpha case layer from a titanium alloy (Ti6Al4V) substrate. The material removal rate, i.e., ablation rate, and ablation threshold of the alpha case titanium were experimentally determined, and compared with those for the removal of bulk Ti6Al4V. Surface morphologies of laser processed alpha case titanium layer, especially that of cracks at different ablated depths, were carefully examined, and also compared with those for Ti6Al4V. It has been shown that in the alpha case layer, laser ablation has always resulted in crack formation while for laser ablation of alpha case free Ti6Al4V layers, cracking was not present. In addition, the surface is rougher within the alpha case layer and becomes smoother (Ra - 110 nm) once the substrate Ti-alloy is reached. The work has demonstrated that laser is a feasible processing tool for removing alpha case titanium, and could also be used for the rapid detection of the presence of alpha case titanium on Ti6Al4V surfaces in aerospace applications.

  14. Interaction of extreme ultraviolet laser radiation with solid surface: ablation, desorption, nanostructuring

    NASA Astrophysics Data System (ADS)

    Kolacek, Karel; Schmidt, Jiri; Straus, Jaroslav; Frolov, Oleksandr; Juha, Libor; Chalupsky, Jaromir

    2015-02-01

    The area, where interaction of focused XUV laser radiation with solid surface takes place, can be divided according to local fluency into desorption region (if fluency is larger than zero and smaller than ablation threshold) and ablation region (if fluency is equal or larger than this threshold). It turned out that a direct nanostructuring (e.g. imprinting diffraction pattern created on edges of windows of proximity standing grid) is possible in the desorption region only. While for femtosecond pulses the particle (atom/molecule) removal-efficiency η in the desorption region is very small (η < 10%), and hence, it can be easily distinguished from the ablation region with η ~ 100%, for nanosecond pulses in desorption region this η rises at easily ablated materials from 0% at the periphery up to ~90% at the ablation contour and, therefore, the boundary between these two regions can be found with the help of nanostructuring only. This rise of removal efficiency could be explained by gradually increased penetration depth (due to gradually removed material) during laser pulse. This is a warning against blind using crater shape for fluency mapping in the case of long laser pulses. On the other hand it is a motivation to study an ablation plum (or ablation jet) and to create a knowledge bank to be used at future numerical modeling of this process.

  15. On the role of chemical reactions in initiating ultraviolet laser ablation in poly(methyl methacrylate)

    SciTech Connect

    Prasad, Manish; Conforti, Patrick F.; Garrison, Barbara J.

    2007-05-15

    The role of chemical reactions is investigated versus the thermal and mechanical processes occurring in a polymer substrate during irradiation by a laser pulse and subsequent ablation. Molecular dynamics simulations with an embedded Monte Carlo based reaction scheme were used to study ultraviolet ablation of poly(methyl methacrylate) at 157 nm. We discuss the onset of ablation, the mechanisms leading to ablation, and the role of stress relaxation of the polymer matrix during ablation. Laser induced heating and chemical decomposition of the polymer substrate are considered as ablation pathways. It is shown that heating the substrate can set off ablation via mechanical failure of the material only for very short laser pulses. For longer pulses, the mechanism of ejection is thermally driven limited by the critical number of bonds broken in the substrate. Alternatively, if the photon energy goes towards direct bond breaking, it initiates chemical reactions, polymer unzipping, and formation of gaseous products, leading to a nearly complete decomposition of the top layers of substrates. The ejection of small molecules has a hollowing out effect on the weakly connected substrates which can lead to lift-off of larger chunks. Excessive pressure buildup upon the creation of gaseous molecules does not lead to enhanced yield. The larger clusters are thermally ejected, and an entrainment of larger polymer fragments in gaseous molecules is not observed.

  16. Plasma mediated ablation of biological tissues with ultrashort laser pulses

    SciTech Connect

    Oraevsky, A.A. |; DaSilva, L.B.; Feit, M.D.

    1995-03-08

    Plasma mediated ablation of collagen gels and porcine cornea was studied at various laser pulse durations in the range from 350 fs to 1 ns at 1,053 nm wavelength. A time resolved stress detection technique was employed to measure transient stress profiles and amplitudes. Optical microscopy was used to characterize ablation craters qualitatively, while a wide band acoustic transducer helped to quantify tissue mechanical response and the ablation threshold. The ablation threshold was measured as a function of laser pulse duration and linear absorption coefficient. For nanosecond pulses the ablation threshold was found to have a strong dependence on the linear absorption coefficient of the material. As the pulse length decreased into the subpicosecond regime the ablation threshold became insensitive to the linear absorption coefficient. The ablation efficiency was found to be insensitive to both the laser pulse duration and the linear absorption coefficient. High quality ablation craters with no thermal or mechanical damage to surrounding material were obtained with 350 fs laser pulses. The mechanism of optical breakdown at the tissue surface was theoretically investigated. In the nanosecond regime, optical breakdown proceeds as an electron collisional avalanche ionization initiated by thermal seed electrons. These seed electrons are created by heating of the tissue by linear absorption. In the ultrashort pulse range, optical breakdown is initiated by the multiphoton ionization of the irradiated medium (6 photons in case of tissue irradiated at 1,053 nm wavelength), and becomes less sensitive to the linear absorption coefficient. The energy deposition profile is insensitive to both the laser pulse duration and the linear absorption coefficient.

  17. Solid sampling with 193-nm excimer laser ablation

    NASA Astrophysics Data System (ADS)

    Delmdahl, Ralph

    2007-02-01

    Reproducible and sensitive elemental analysis of solid samples is a crucial task in areas of geology (e.g. microanalysis of fluid inclusions), material sciences, industrial quality control as well as in environmental, forensic and biological studies. To date the most versatile detection method is mass-spectroscopic multi-element analysis. In order to obtain reproducible results, this requires transferring the solid sample into the gas-phase while preserving the sample's stoichiometric composition. Laser ablation in combination with Inductively Coupled Plasma-Mass Spectrometry (LA-ICP-MS) is a proven powerful technique to meet the requirements for reliable solid sample analysis. The sample is laser ablated in an air-tight cell and the aerosol is carried by an inert gas to a micro-wave induced plasma where its constituents are atomized and ionized prior to mass analysis. The 193 nm excimer laser ablation, in particular, provides athermal sample ablation with very precise lateral ablation and controlled depth profiling. The high photon energy and beam homogeneity of the 193 nm excimer laser system avoids elemental fractionation and permits clean ablation of even transmissive solid materials such as carbonates, fluorites and pure quartz.

  18. Edge isolation of transparent conductive polymer (TCP) thin films on flexible substrates using UV laser ablation.

    PubMed

    Hsiao, Wen-Tse; Tseng, Shih-Feng; Huang, Kuo-Cheng; Chiang, Donyau; Chen, Ming-Fei

    2012-06-01

    The purpose of this study was to directly use the writing techniques for the complex electrode edge isolation of transparent conductive polymer (TCP) thin films by a nanosecond pulsed UV laser processing system. The processing parameters including the laser pulse energy, the pulse repetition frequency, and the scan speed of galvanometers were examined to ablate the TCP films deposited on polyethylene terephtalate substrates of 188 microm thick. The thickness of TCP films was approximately 20 nm. The laser pulse repetition frequency and the scan speed of galvanometers were applied to calculate the overlapping rate of laser spots and to discuss the patterning region quality. Surface morphology, edge quality, and width and depth of edge isolated patterning structures after laser ablation process were measured by a three-dimensional confocal laser scanning microscope. In addition, the electrical conductivity of ablated TCP films was measured by a four-point probes instrument. After isolated line patterning was formed, the ablated TCP films with a better edge quality were obtained directly when the overlapping rate of laser spots, the scan speed, and the pulse repetition rate were 83.3%, 200 mm/s, and 40 kHz, respectively. The better surface morphology of electrode pattern structures was also obtained when the scan speed and the pulse repetition rate were 500 mm/s and 40 kHz, respectively.

  19. Formation of nanostructures under femtosecond laser ablation of metals

    SciTech Connect

    Ashitkov, S I; Romashevskii, S A; Komarov, P S; Burmistrov, A A; Agranat, M B; Zhakhovskii, V V; Inogamov, N A

    2015-06-30

    We present the results of studying the morphology of the modified surface of aluminium, nickel and tantalum after ablation of the surface layer by a femtosecond laser pulse. The sizes of characteristic elements of a cellular nanostructure are found to correlate with thermo-physical properties of the material and the intensity of laser radiation. (superstrong light fields)

  20. Mechanisms of nanoparticle formation by ultra-short laser ablation of metals in liquid environment.

    PubMed

    Povarnitsyn, Mikhail E; Itina, Tatiana E; Levashov, Pavel R; Khishchenko, Konstantin V

    2013-03-07

    Laser ablation in liquids is now commonly used to produce colloidal nanoparticles (NPs) that have found numerous applications in different areas. In experiments, NPs of different materials can be rather easily obtained by using laser systems with various pulse durations, shapes, wavelengths, and fluences. In this paper, we focus our attention on metal (gold) NPs produced by ultra-short laser pulses. To better understand the mechanisms of the NPs formation, we perform modeling of femtosecond laser interactions with a gold target in the presence of liquid (water). Simulation of the ablation process over several nanoseconds shows that most of the primary NPs originate from the ablated metastable liquid layer, whereas only a minority is formed by condensation inside the cavitation bubble. These particles will further grow/evaporate, and coagulate during a much longer collision stage in the liquid colloid.

  1. UV solid state laser ablation of intraocular lenses

    NASA Astrophysics Data System (ADS)

    Apostolopoulos, A.; Lagiou, D. P.; Evangelatos, Ch.; Spyratou, E.; Bacharis, C.; Makropoulou, M.; Serafetinides, A. A.

    2013-06-01

    Commercially available intraocular lenses (IOLs) are manufactured from silicone and acrylic, both rigid (e.g. PMMA) and foldable (hydrophobic or hydrophilic acrylic biomaterials), behaving different mechanical and optical properties. Recently, the use of apodizing technology to design new diffractive-refractive multifocals improved the refractive outcome of these intraocular lenses, providing good distant and near vision. There is also a major ongoing effort to refine laser refractive surgery to correct other defects besides conventional refractive errors. Using phakic IOLs to treat high myopia potentially provides better predictability and optical quality than corneal-based refractive surgery. The aim of this work was to investigate the effect of laser ablation on IOL surface shaping, by drilling circular arrays of holes, with a homemade motorized rotation stage, and scattered holes on the polymer surface. In material science, the most popular lasers used for polymer machining are the UV lasers, and, therefore, we tried in this work the 3rd and the 5th harmonic of a Q-switched Nd:YAG laser (λ=355 nm and λ=213 nm respectively). The morphology of the ablated IOL surface was examined with a scanning electron microscope (SEM, Fei - Innova Nanoscope) at various laser parameters. Quantitative measurements were performed with a contact profilometer (Dektak-150), in which a mechanical stylus scanned across the surface of gold-coated IOLs (after SEM imaging) to measure variations in surface height and, finally, the ablation rates were also mathematically simulated for depicting the possible laser ablation mechanism(s). The experimental results and the theoretical modelling of UV laser interaction with polymeric IOLs are discussed in relation with the physical (optical, mechanical and thermal) properties of the material, in addition to laser radiation parameters (laser energy fluence, number of pulses). The qualitative aspects of laser ablation at λ=213 nm reveal a

  2. Ultrashort pulse laser ablation of dielectrics: Thresholds, mechanisms, role of breakdown

    PubMed Central

    Mirza, Inam; Bulgakova, Nadezhda M.; Tomáštík, Jan; Michálek, Václav; Haderka, Ondřej; Fekete, Ladislav; Mocek, Tomáš

    2016-01-01

    In this paper, we establish connections between the thresholds and mechanisms of the damage and white-light generation upon femtosecond laser irradiation of wide-bandgap transparent materials. On the example of Corning Willow glass, evolution of ablation craters, their quality, and white-light emission were studied experimentally for 130-fs, 800-nm laser pulses. The experimental results indicate co-existence of several ablation mechanisms which can be separated in time. Suppression of the phase explosion mechanism of ablation was revealed at the middle of the irradiation spots. At high laser fluences, air ionization was found to strongly influence ablation rate and quality and the main mechanisms of the influence are analysed. To gain insight into the processes triggered by laser radiation in glass, numerical simulations have been performed with accounting for the balance of laser energy absorption and its distribution/redistribution in the sample, including bremsstrahlung emission from excited free-electron plasma. The simulations have shown an insignificant role of avalanche ionization at such short durations of laser pulses while pointing to high average energy of electrons up to several dozens of eV. At multi-pulse ablation regimes, improvement of crater quality was found as compared to single/few pulses. PMID:27991543

  3. Ultrashort pulse laser ablation of dielectrics: Thresholds, mechanisms, role of breakdown

    NASA Astrophysics Data System (ADS)

    Mirza, Inam; Bulgakova, Nadezhda M.; Tomáštík, Jan; Michálek, Václav; Haderka, Ondřej; Fekete, Ladislav; Mocek, Tomáš

    2016-12-01

    In this paper, we establish connections between the thresholds and mechanisms of the damage and white-light generation upon femtosecond laser irradiation of wide-bandgap transparent materials. On the example of Corning Willow glass, evolution of ablation craters, their quality, and white-light emission were studied experimentally for 130-fs, 800-nm laser pulses. The experimental results indicate co-existence of several ablation mechanisms which can be separated in time. Suppression of the phase explosion mechanism of ablation was revealed at the middle of the irradiation spots. At high laser fluences, air ionization was found to strongly influence ablation rate and quality and the main mechanisms of the influence are analysed. To gain insight into the processes triggered by laser radiation in glass, numerical simulations have been performed with accounting for the balance of laser energy absorption and its distribution/redistribution in the sample, including bremsstrahlung emission from excited free-electron plasma. The simulations have shown an insignificant role of avalanche ionization at such short durations of laser pulses while pointing to high average energy of electrons up to several dozens of eV. At multi-pulse ablation regimes, improvement of crater quality was found as compared to single/few pulses.

  4. A study of photothermal laser ablation of various polymers on microsecond time scales.

    PubMed

    Kappes, Ralf S; Schönfeld, Friedhelm; Li, Chen; Golriz, Ali A; Nagel, Matthias; Lippert, Thomas; Butt, Hans-Jürgen; Gutmann, Jochen S

    2014-01-01

    To analyze the photothermal ablation of polymers, we designed a temperature measurement setup based on spectral pyrometry. The setup allows to acquire 2D temperature distributions with 1 μm size and 1 μs time resolution and therefore the determination of the center temperature of a laser heating process. Finite element simulations were used to verify and understand the heat conversion and heat flow in the process. With this setup, the photothermal ablation of polystyrene, poly(α-methylstyrene), a polyimide and a triazene polymer was investigated. The thermal stability, the glass transition temperature Tg and the viscosity above Tg were governing the ablation process. Thermal decomposition for the applied laser pulse of about 10 μs started at temperatures similar to the start of decomposition in thermogravimetry. Furthermore, for polystyrene and poly(α-methylstyrene), both with a Tg in the range between room and decomposition temperature, ablation already occurred at temperatures well below the decomposition temperature, only at 30-40 K above Tg. The mechanism was photomechanical, i.e. a stress due to the thermal expansion of the polymer was responsible for ablation. Low molecular weight polymers showed differences in photomechanical ablation, corresponding to their lower Tg and lower viscosity above the glass transition. However, the difference in ablated volume was only significant at higher temperatures in the temperature regime for thermal decomposition at quasi-equilibrium time scales.

  5. Thermal ablation of liver metastases from colorectal cancer: radiofrequency, microwave and laser ablation therapies.

    PubMed

    Vogl, Thomas J; Farshid, Parviz; Naguib, Nagy N N; Darvishi, Abbas; Bazrafshan, Babak; Mbalisike, Emmanuel; Burkhard, Thorsten; Zangos, Stephan

    2014-07-01

    Surgery is currently considered the treatment of choice for patients with colorectal cancer liver metastases (CRLM) when resectable. The majority of these patients can also benefit from systemic chemotherapy. Recently, local or regional therapies such as thermal ablations have been used with acceptable outcomes. We searched the medical literature to identify studies and reviews relevant to radiofrequency (RF) ablation, microwave (MW) ablation and laser-induced thermotherapy (LITT) in terms of local progression, survival indexes and major complications in patients with CRLM. Reviewed literature showed a local progression rate between 2.8 and 29.7 % of RF-ablated liver lesions at 12-49 months follow-up, 2.7-12.5 % of MW ablated lesions at 5-19 months follow-up and 5.2 % of lesions treated with LITT at 6-month follow-up. Major complications were observed in 4-33 % of patients treated with RF ablation, 0-19 % of patients treated with MW ablation and 0.1-3.5 % of lesions treated with LITT. Although not significantly different, the mean of 1-, 3- and 5-year survival rates for RF-, MW- and laser ablated lesions was (92.6, 44.7, 31.1 %), (79, 38.6, 21 %) and (94.2, 61.5, 29.2 %), respectively. The median survival in these methods was 33.2, 29.5 and 33.7 months, respectively. Thermal ablation may be an appropriate alternative in patients with CRLM who have inoperable liver lesions or have operable lesions as an adjunct to resection. However, further competitive evaluation should clarify the efficacy and priority of these therapies in patients with colorectal cancer liver metastases.

  6. Optical properties measurement of the laser-ablated tissues for the combined laser ablation with photodynamic therapy

    NASA Astrophysics Data System (ADS)

    Honda, Norihiro; Ishii, Katsunori; Awazu, Kunio

    2012-03-01

    Laser ablation therapy combined with photodynamic therapy (PDT) is studied for treatment of advanced cancers. The clinical outcome of PDT may be improved by the accurate knowledge about the light distribution within tissue. Optical properties [absorption coefficient (μa), scattering coefficient (μs), anisotropy factor (g), refractive index, etc.] of tissues help us realizing a light propagation through the tissue. It is important to understand of the effect of laser coagulation formed by laser ablation to PDT. The aim of this study is to estimate of influence of coagulated region to PDT for effective PDT combined laser ablation therapy. We evaluated the optical property of mouse tumor tissue in native and coagulated state using a double integrating sphere system and an inverse Monte Carlo method in the wavelength range from 350 to 1000 nm. After laser ablation, the μa and reduced scattering coefficient spectra of coagulated tissues were increased in the wavelength range from 350 to 1000 nm. The optical penetration depth of coagulated tissues is 1.2-2.9 times lower than the native state in the wavelength range from 350 to 1000 nm. The intensity of the light energy inside the coagulated tissue falls to about 60% of its original value at the end of coagulated layer. The evaluation of light energy distribution by the determination of the tissues optical properties could be useful for optimization of the treatment procedure in combined laser ablation with PDT.

  7. Laser ablation sample transfer for mass spectrometry imaging.

    PubMed

    Park, Sung-Gun; Murray, Kermit K

    2015-01-01

    Infrared laser ablation sample transfer (IR-LAST) is a novel ambient sampling technique for mass spectrometry. In this technique, a pulsed mid-IR laser is used to ablate materials that are collected for mass spectrometry analysis; the material can be a solid sample or deposited on a sample target. After collection, the sample can be further separated or analyzed directly by mass spectrometry. For IR-LAST sample transfer tissue imaging using MALDI mass spectrometry, a tissue section is placed on a sample slide and material transferred to a target slide by scanning the tissue sample under a focused laser beam using transmission-mode (back side) IR laser ablation. After transfer, the target slide is analyzed using MALDI imaging. The spatial resolution is approximately 400 μm and limited by the spread of the laser desorption plume. IR-LAST for MALDI imaging provides several new capabilities including ambient sampling, area to spot concentration of ablated material, multiple ablation and analysis from a single section, and direct deposition on matrix-free nanostructured targets.

  8. Ablation Studies of Enamel Tissue Using Pulsed HF Laser

    DTIC Science & Technology

    2007-11-02

    and enamel has been successful. The reason is thought to be due to high absorption coefficients of hydroxyapatite [Ca10(Po4)6(OH2)] with a total...secondary absorption peak of hydroxyapatite lies, a less violent and cleaner ablation of enamel compared with its main absorption peak at 9.6 µm is...1 of 4 Ablation Studies of Enamel Tissue using Pulsed HF Laser M.E. Khosroshahi, B.A. Ghasemi Amirkabir University of Technology, School of

  9. Laser Ablation of Biological Tissue Using Pulsed CO{sub 2} Laser

    SciTech Connect

    Hashishin, Yuichi; Sano, Shu; Nakayama, Takeyoshi

    2010-10-13

    Laser scalpels are currently used as a form of laser treatment. However, their ablation mechanism has not been clarified because laser excision of biological tissue occurs over a short time scale. Biological tissue ablation generates sound (laser-induced sound). This study seeks to clarify the ablation mechanism. The state of the gelatin ablation was determined using a high-speed video camera and the power reduction of a He-Ne laser beam. The aim of this study was to clarify the laser ablation mechanism by observing laser excision using the high-speed video camera and monitoring the power reduction of the He-Ne laser beam. We simulated laser excision of a biological tissue by irradiating gelatin (10 wt%) with radiation from a pulsed CO{sub 2} laser (wavelength: 10.6 {mu}m; pulse width: 80 ns). In addition, a microphone was used to measure the laser-induced sound. The first pulse caused ablation particles to be emitted in all directions; these particles were subsequently damped so that they formed a mushroom cloud. Furthermore, water was initially evaporated by laser irradiation and then tissue was ejected.

  10. Molecular dynamics simulations studies of laser ablation in metals

    SciTech Connect

    Roth, Johannes; Sonntag, Steffen; Karlin, Johannes; Paredes, Carolina Trichet; Sartison, Marc; Krauss, Armin; Trebin, Hans-Rainer

    2012-07-30

    An overview of several aspects of our recent molecular dynamics simulations of femtosecond laser ablation is presented. This includes the study of phase diagrams for suitable interactions, analysis of ablated material and bubble formation below threshold, study of two-pulse ablation and the classification of materials with respect to electron properties and electron-phonon coupling in the two-temperature model. A treatment of boundary conditions and of an extended twotemperature model is also included. Most of the results apply to aluminum, others also to copper and iron, and to metals in general.

  11. Laser Ablation Increases PEM/Catalyst Interfacial Area

    NASA Technical Reports Server (NTRS)

    Whitacre, Jay; Yalisove, Steve

    2009-01-01

    An investigational method of improving the performance of a fuel cell that contains a polymer-electrolyte membrane (PEM) is based on the concept of roughening the surface of the PEM, prior to deposition of a thin layer of catalyst, in order to increase the PEM/catalyst interfacial area and thereby increase the degree of utilization of the catalyst. The roughening is done by means of laser ablation under carefully controlled conditions. Next, the roughened membrane surface is coated with the thin layer of catalyst (which is typically platinum), then sandwiched between two electrode/catalyst structures to form a membrane/ele c t - rode assembly. The feasibility of the roughening technique was demonstrated in experiments in which proton-conducting membranes made of a perfluorosulfonic acid-based hydrophilic, protonconducting polymer were ablated by use of femtosecond laser pulses. It was found that when proper combinations of the pulse intensity, pulse-repetition rate, and number of repetitions was chosen, the initially flat, smooth membrane surfaces became roughened to such an extent as to be converted to networks of nodules interconnected by filaments (see Figure 1). In further experiments, electrochemical impedance spectroscopy (EIS) was performed on a pristine (smooth) membrane and on two laser-roughened membranes after the membranes were coated with platinum on both sides. Some preliminary EIS data were interpreted as showing that notwithstanding the potential for laser-induced damage, the bulk conductivities of the membranes were not diminished in the roughening process. Other preliminary EIS data (see Figure 2) were interpreted as signifying that the surface areas of the laser-roughened membranes were significantly greater than those of the smooth membrane. Moreover, elemental analyses showed that the sulfur-containing molecular groups necessary for proton conduction remained intact, even near the laser-roughened surfaces. These preliminary results can be taken

  12. Shock pressures induced in condensed matter by laser ablation.

    PubMed

    Swift, Damian C; Tierney, Thomas E; Kopp, Roger A; Gammel, J Tinka

    2004-03-01

    The Trident laser was used to induce shock waves in samples of solid elements, with atomic numbers ranging from Be to Au, using pulses of 527 nm light around 1 ns long with irradiances of the order of 0.1 to 10 PW/m(2). States induced by the resulting ablation process were investigated using laser Doppler velocimetry to measure the velocity history of the opposite surface. By varying the energy in the laser pulse, relations were inferred between the irradiance and the induced pressure. For samples in vacuo, an irradiance constant in time does not produce a constant pressure. Radiation hydrodynamics simulations were used to investigate the relationship between the precise pulse shape and the pressure history. In this regime of time and irradiance, it was possible to reproduce the experimental data to within their uncertainty by including conductivity-dependent deposition of laser energy, heat conduction, gray radiation diffusion, and three temperature hydrodynamics in the treatment of the plasma, with ionizations calculated using the Thomas-Fermi equation. States induced in the solid sample were fairly insensitive to the details of modeling in the plasma, so Hugoniot points may be estimated from experiments of this type given a reasonable model of the plasma. More useful applications include the generation of dynamic loading to investigate compressive strength and phase transitions, and for sample recovery.

  13. Pulsed laser ablation of dental calculus in the near ultraviolet.

    PubMed

    Schoenly, Joshua E; Seka, Wolf; Rechmann, Peter

    2014-02-01

    Pulsed lasers emitting wavelengths near 400 nm can selectively ablate dental calculus without damaging underlying and surrounding sound dental hard tissue. Our results indicate that calculus ablation at this wavelength relies on the absorption of porphyrins endogenous to oral bacteria commonly found in calculus. Sub- and supragingival calculus on extracted human teeth, irradiated with 400-nm, 60-ns laser pulses at ≤8  J/cm2, exhibits a photobleached surface layer. Blue-light microscopy indicates this layer highly scatters 400-nm photons, whereas fluorescence spectroscopy indicates that bacterial porphyrins are permanently photobleached. A modified blow-off model for ablation is proposed that is based upon these observations and also reproduces our calculus ablation rates measured from laser profilometry. Tissue scattering and a stratified layering of absorbers within the calculus medium explain the gradual decrease in ablation rate from successive pulses. Depending on the calculus thickness, ablation stalling may occur at <5  J/cm2 but has not been observed above this fluence.

  14. Microwave ablation versus laser ablation in occluding lateral veins in goats.

    PubMed

    Wang, Xu-hong; Wang, Xiao-ping; Su, Wen-juan; Yuan, Yuan

    2016-02-01

    Increasing number of endovenous techniques are available for the treatment of saphenous vein reflux and endovenous laser ablation (EVLA) is a frequently used method. A newly developed alternative, based on thermal therapy, is endovenous microwave ablation (EMA). This study evaluated the effect of the two procedures, in terms of coagulation and histological changes, in occluding lateral veins in goats. Twelve animals were randomized into two group, with 6 treated with EMA (EMA group), and the rest 6 with EVLA (EVLA group). Results of coagulation, including coagulation, fibrinolysis and platelet activation, were assessed at three or four different time points: before, immediately after, 24 h (and 48 h) after ablation. The diameter change, a measure of efficacy, was ultrasonographically measured before and 1 month after the ablation. Histological changes were grossly and microscopically evaluated immediately, 1 and 3 month(s) after the ablation. The length of the ablated vein and preoperative average diameter were comparable between the two groups. In both EMA and EVLA groups, several coagulation parameters, fibrinolysis and platelet activation parameters only underwent slight changes. Ultrasound imaging displayed that the diameter reduction of the veins treated by EMA was significantly larger than by EVLA, in consistent with the results of macroscopic examination. Microscopic examination revealed necrosis and thickening of the vein wall, and occlusion of the lumen within 3 months after ablation in both EMA and EVLA groups. It is concluded that EMA is a minimally invasive therapy, which appears to be safe and effective for treatment of lateral veins in goats.

  15. Nanostructures synthesis by femtosecond laser ablation of glasses

    NASA Astrophysics Data System (ADS)

    Vipparty, D.; Tan, B.; Venkatakrishnan, K.

    2012-10-01

    In this article, we investigate the variations in ablation dynamics that result in diverse nanostructures on SiO2 based glass samples. A three-dimensional fibrous nanoparticle agglomerate was observed on sodalime glass when exposed to femtosecond laser irradiation. The fused nanoparticles have diameters ranging from 30 nm to 70 nm. Long continuous nanofibers of extremely high aspect ratio (certain fibers up to 100 000:1) were obtained by exposing silica glass surface to femtosecond laser irradiation at MHz repetition rate in air. A nanostructure assembly comprising of nanofiber and nanoparticle agglomerates was also observed by ablating silica glass. From our experimental analysis, it was determined that variation in bandgap and material composition alters ablation dynamics and dictates the response of glass to femtosecond laser irradiation, ultimately leading to the formation of structures with varying morphology on silica and sodalime glass. The possible underlying mechanisms that produce such nanostructures on glass specimens have also been explored.

  16. UV-laser ablation of sensory cells in living insects

    NASA Astrophysics Data System (ADS)

    Fuhr, G.; Ronacher, B.; Krahe, R.; Fest, S.; Shirley, S. G.; Rogaschewski, S.

    An experimental set-up for applying pulsed UV-laser ablation to the integument of insects and the high precision of ablation is demonstrated. In order to test for possible detrimental effects on physiological responses, this technique was applied to the ears of migratory locust (Locusta migratoria L.). The handling of living insects, the survival, and physiological response after treatment are described. We selectively interrupted the d-receptor of the tympanal organ, which is the receptor system responsible for the locust's sensitivity in the high-frequency range (>10 kHz). The effects of the laser treatment were tested by determining hearing thresholds in electrophysiological recordings from the tympanal nerves. In agreement with the literature, the interruption of the d-receptors led to a significant shift towards higher values of the thresholds in the high-frequency range. Future perspectives and biological applications of UV-laser ablation are discussed.

  17. CO2 laser ablative etching of polyethylene terephthalate

    NASA Astrophysics Data System (ADS)

    Dyer, P. E.; Oldershaw, G. A.; Sidhu, J.

    1989-06-01

    Films of polyethylene terephthalate (PET) can be successfully etched with 9 μm radiation from a pulsed TEA CO2 laser. The relationship between etch depth and fluence is broadly similar to that observed for excimer laser etching but with a less well-defined threshold. Time-resolved photoacoustic measurements of stress waves generated in the interaction show that at a fluence of 1.8 J cm-2 ablation occurs 100 200 ns after the start of the laser pulse, a time which is consistent with the rate of thermal decomposition of PET. The volatile products of ablation are carbon monoxide, carbon dioxide, methane, ethyne, ethene, benzene, ethanal, and small quantities of other products. For fluences close to and appreciably above the threshold the ablated material consists predominantly of involatile species of relatively high molecular weight, whereas at higher fluences substantial fragmentation of the polymer to small molecules occurs.

  18. Ablative fractional laser resurfacing helps treat restrictive pediatric scar contractures.

    PubMed

    Krakowski, Andrew C; Goldenberg, Alina; Eichenfield, Lawrence F; Murray, Jill-Peck; Shumaker, Peter R

    2014-12-01

    Conventional management of debilitating pediatric scar contractures, including hand therapy and surgery, may often be beset by delayed treatment, suboptimal results, and additional surgical morbidity. Ablative fractional laser resurfacing is an emerging adjunctive procedural option for scar contractures because of its promising efficacy and safety profile. However, its use to improve function has not been studied in the pediatric population. Herein we report 2 pediatric patients with recalcitrant scar contractures, causing persistent functional deficits, treated with an ablative fractional laser protocol. Both patients experienced rapid and cumulative subjective and objective improvements in range of motion and function as measured by an independent occupational therapist without reported complications. We highlight ablative fractional laser resurfacing as a novel and promising tool in the management of function-limiting scar contractures in children and propose that the technique be incorporated into existing scar treatment paradigms, guided by future research.

  19. Dentin mid-infrared laser ablation at various lasing parameters

    NASA Astrophysics Data System (ADS)

    Papadopoulos, Dimitris N.; Papagiakoumou, Eirini I.; Makropoulou, Mersini I.; Khabbaz, Marouan G.; Serafetinides, Alexander A.

    2005-01-01

    In this study a frustrated total internal reflection (FTIR) Q-switched and free-running Er:YAG laser, as well as a novel design transversally excited atmospheric pressure (TEA) oscillator-double amplifier corona preionised high beam quality Hydrogen-Fluoride (HF) laser system, all developed in our lab, were used in dentin ablation experiments. In the case of the Er:YAG laser, pulses of 190 ns in Q-switched operation and of 80 μs pulse width in free-running operation at 2.94 μm were used, while HF laser pulses of 39 ns in the wavelength range of 2.6-3.1 μm in a predominantly TEM00 beam were also used to interact in vitro with dentin tissue. Several samples of freshly extracted human teeth were used, cut longitudinally in facets of 0.4-1.5 mm thick. Ablation experiments were conducted with the laser beam directly focused on the tissue or after being waveguided through suitable mid-IR fiber/waveguide alternatively ended with quartz end-sealing caps. The correlation between the various laser beam parameters, as wavelength, pulse duration, repetition rate, energy and spatial distribution of the beam profile and the ablative characteristics (ablation rates, tissue surface morphology) of dentin surface were investigated.

  20. Band-pass filters for THz spectral range fabricated by laser ablation

    NASA Astrophysics Data System (ADS)

    Voisiat, B.; Bičiūnas, A.; Kašalynas, I.; Račiukaitis, G.

    2011-09-01

    The terahertz resonant metal-mesh filters were fabricated using the laser direct writing technique. UV picosecond laser was employed to cut matrixes of cross-shaped holes in stainless steel foil and molybdenum layer deposited on polyimide substrate. Different laser processing strategies were developed: holes were cut through in the metal foil and the molybdenum film was removed from the polyimide by laser ablation. Band-pass filters with a different center frequency were designed and fabricated. The regular shape, smoothness of edges and sharpness of corners of the cross-shaped holes in the metal were the main attributes for quality assessment for the laser ablation process. Spectral characteristics of the filters, determined by the mesh period, cross-arm length, and its width, were investigated by terahertz time-domain spectroscopy and conventional space-domain Fourier transform spectroscopy. Experimental data were supported by three-dimensional finite-difference time-domain simulations.

  1. Cavitation effect of holmium laser pulse applied to ablation of hard tissue underwater.

    PubMed

    Lü, Tao; Xiao, Qing; Xia, Danqing; Ruan, Kai; Li, Zhengjia

    2010-01-01

    To overcome the inconsecutive drawback of shadow and schlieren photography, the complete dynamics of cavitation bubble oscillation or ablation products induced by a single holmium laser pulse [2.12 microm, 300 micros (FWHM)] transmitted in different core diameter (200, 400, and 600 microm) fibers is recorded by means of high-speed photography. Consecutive images from high-speed cameras can stand for the true and complete process of laser-water or laser-tissue interaction. Both laser pulse energy and fiber diameter determine cavitation bubble size, which further determines acoustic transient amplitudes. Based on the pictures taken by high-speed camera and scanned by an optical coherent microscopy (OCM) system, it is easily seen that the liquid layer at the distal end of the fiber plays an important role during the process of laser-tissue interaction, which can increase ablation efficiency, decrease heat side effects, and reduce cost.

  2. Laser ablated zirconium plasma: A source of neutral zirconium

    SciTech Connect

    Yadav, Dheerendra; Thareja, Raj K.

    2010-10-15

    The authors report spectroscopic investigations of laser produced zirconium (Zr) plasma at moderate laser fluence. At low laser fluence the neutral zirconium species are observed to dominate over the higher species of zirconium. Laser induced fluorescence technique is used to study the velocity distribution of ground state neutral zirconium species. Two-dimensional time-resolved density distributions of ground state zirconium is mapped using planner laser induced fluorescence imaging and total ablated mass of neutral zirconium atoms is estimated. Temporal and spatial evolutions of electron density and temperature are discussed by measuring Stark broadened profile and ratio of intensity of emission lines, respectively.

  3. Liquid-assisted laser ablation of advanced ceramics and glass-ceramic materials

    NASA Astrophysics Data System (ADS)

    Garcia-Giron, A.; Sola, D.; Peña, J. I.

    2016-02-01

    In this work, results obtained by laser ablation of advanced ceramics and glass-ceramic materials assisted by liquids are reported. A Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulse-width in the nanosecond range was used to machine the materials, which were immersed in water and ethylene glycol. Variation in geometrical parameters, morphology, and ablation yields were studied by using the same laser working conditions. It was observed that machined depth and removed volume depended on the thermal, optical, and mechanical features of the processed materials as well as on the properties of the surrounding medium in which the laser processing was carried out. Variation in ablation yields was studied in function of the liquid used to assist the laser process and related to refractive index and viscosity. Material features and working conditions were also related to the obtained results in order to correlate ablation parameters with respect to the hardness of the processed materials.

  4. Pulsed laser ablation of polymers for display applications

    NASA Astrophysics Data System (ADS)

    Pedder, James E. A.; Holmes, Andrew S.; Booth, Heather J.

    2008-02-01

    Laser micromachining by ablation is a well established technique used for the production of 2.5D and 3D features in a wide variety of materials. The fabrication of stepped, multi-level, structures can be achieved using a number of binary mask projection techniques using excimer lasers. Alternatively, direct-writing of complex 2.5D features can easily be achieved with solid-state lasers. Excimer laser ablation using half-tone masks allows almost continuous surface relief and the generation of features with low surface roughness. We have developed techniques to create large arrays of repeating micro-optical structures on polymer substrates. Here, we show our recent developments in laser structuring with the combination of half-tone and binary mask techniques.

  5. Aerospace Laser Ignition/Ablation Variable High Precision Thruster

    NASA Technical Reports Server (NTRS)

    Campbell, Jonathan W. (Inventor); Edwards, David L. (Inventor); Campbell, Jason J. (Inventor)

    2015-01-01

    A laser ignition/ablation propulsion system that captures the advantages of both liquid and solid propulsion. A reel system is used to move a propellant tape containing a plurality of propellant material targets through an ignition chamber. When a propellant target is in the ignition chamber, a laser beam from a laser positioned above the ignition chamber strikes the propellant target, igniting the propellant material and resulting in a thrust impulse. The propellant tape is advanced, carrying another propellant target into the ignition chamber. The propellant tape and ignition chamber are designed to ensure that each ignition event is isolated from the remaining propellant targets. Thrust and specific impulse may by precisely controlled by varying the synchronized propellant tape/laser speed. The laser ignition/ablation propulsion system may be scaled for use in small and large applications.

  6. Hydrodynamic simulations of metal ablation by femtosecond laser irradiation

    SciTech Connect

    Colombier, J.P.; Combis, P.; Bonneau, F.

    2005-04-15

    Ablation of Cu and Al targets has been performed with 170 fs laser pulses in the intensity range of 10{sup 12}-10{sup 14} W cm{sup -2}. We compare the measured removal depth with 1D hydrodynamic simulations. The electron-ion temperature decoupling is taken into account using the standard two-temperature model. The influence of the early heat transfer by electronic thermal conduction on hydrodynamic material expansion and mechanical behavior is investigated. A good agreement between experimental and numerical matter ablation rates shows the importance of including solid-to-vapor evolution of the metal in the current modeling of the laser matter interaction.

  7. Optical feedback-induced light modulation for fiber-based laser ablation.

    PubMed

    Kang, Hyun Wook

    2014-11-01

    Optical fibers have been used as a minimally invasive tool in various medical fields. However, due to excessive heat accumulation, the distal end of a fiber often suffers from severe melting or devitrification, leading to the eventual fiber failure during laser treatment. In order to minimize thermal damage at the fiber tip, an optical feedback sensor was developed and tested ex vivo. Porcine kidney tissue was used to evaluate the feasibility of optical feedback in terms of signal activation, ablation performance, and light transmission. Testing various signal thresholds demonstrated that 3 V was relatively appropriate to trigger the feedback sensor and to prevent the fiber deterioration during kidney tissue ablation. Based upon the development of temporal signal signatures, full contact mode rapidly activated the optical feedback sensor possibly due to heat accumulation. Modulated light delivery induced by optical feedback diminished ablation efficiency by 30% in comparison with no feedback case. However, long-term transmission results validated that laser ablation assisted with optical feedback was able to almost consistently sustain light delivery to the tissue as well as ablation efficiency. Therefore, an optical feedback sensor can be a feasible tool to protect optical fiber tips by minimizing debris contamination and delaying thermal damage process and to ensure more efficient and safer laser-induced tissue ablation.

  8. Femtosecond laser ablation of polymethylmethacrylate via dual-color synthesized waveform

    SciTech Connect

    Yang, Chan-Shan; Zaytsev, Alexey; Lin, Chih-Hsuan; Teng, Kuei-Chung; Her, Tsing-Hua; Pan, Ci-Ling

    2015-02-02

    We have demonstrated the laser ablation of PMMA using dual-color waveform synthesis of the fundamental (ω) and its second-harmonic (2ω) of a femtosecond Ti:Sapphire laser. A modest and yet clear modulation (∼22%) in ablated area versus relative phase between the 2ω and ω beams with a power-ratio of 15% (28/183 mW) is revealed. This is explained qualitatively by the dependence of ablation on multiphoton ionization of which the rate is related to the relative phase of the synthesized waveform. At higher peak power ratios, the modulation decreases rapidly, as the two-photon-ionization rate of the 2ω dominates over that of the three- to four- photon ionization of the ω beam. This technique demonstrates the feasibility of phase-controlled laser processing of materials.

  9. Hyperthermal Pulsed-Laser Ablation Beams for Film Deposition and Surface Microstructural Engineering

    SciTech Connect

    Lowndes, D.H.

    1999-11-08

    This paper presents an overview of pulsed-laser ablation for film deposition and surface microstructure formation. By changing the ambient gas pressure from high vacuum to several Torr (several hundred Pa) and by selecting the pulsed-laser wavelength, the kinetic energy of ablated atoms/ions can be varied from several hundred eV down to {approximately}0.1 eV and films ranging from superhard to nanocrystalline may be deposited. Furthermore, cumulative (multi-pulse) irradiation of a semiconductor surface (e.g. silicon) in an oxidizing gas (0{sub 2}, SF{sub 6}) et atmospheric pressure can produce dense, self-organized arrays of high-aspect-ratio microcolumns or microcones. Thus, a wide range of materials synthesis and processing opportunities result from the hyperthermal flux and reactive growth conditions provided by pulsed-laser ablation.

  10. Fabrication of pillared PLGA microvessel scaffold using femtosecond laser ablation

    PubMed Central

    Wang, Hsiao-Wei; Cheng, Chung-Wei; Li, Ching-Wen; Chang, Han-Wei; Wu, Ping-Han; Wang, Gou-Jen

    2012-01-01

    One of the persistent challenges confronting tissue engineering is the lack of intrinsic microvessels for the transportation of nutrients and metabolites. An artificial microvascular system could be a feasible solution to this problem. In this study, the femtosecond laser ablation technique was implemented for the fabrication of pillared microvessel scaffolds of polylactic-co-glycolic acid (PLGA). This novel scaffold facilitates implementation of the conventional cell seeding process. The progress of cell growth can be observed in vitro by optical microscopy. The problems of becoming milky or completely opaque with the conventional PLGA scaffold after cell seeding can be resolved. In this study, PLGA microvessel scaffolds consisting of 47 μm × 80 μm pillared branches were produced. Results of cell culturing of bovine endothelial cells demonstrate that the cells adhere well and grow to surround each branch of the proposed pillared microvessel networks. PMID:22605935

  11. Erbium oxide thin films on Si(100) obtained by laser ablation and electron beam evaporation

    NASA Astrophysics Data System (ADS)

    Queralt, X.; Ferrater, C.; Sánchez, F.; Aguiar, R.; Palau, J.; Varela, M.

    1995-02-01

    Erbium oxide thin films have been obtained by laser ablation and electron beam evaporation techniques on Si(100) substrates. The samples were grown under different conditions of oxygen atmosphere and substrate temperature without any oxidation process after deposition. The crystal structure has been studied by X-ray diffraction. Films obtained by laser ablation are highly textured in the [ hhh] direction, although this depends on the conditions of oxygen pressure and substrate temperature. In order to study the depth composition profile of the thin films and the interdiffusion of erbium metal and oxygen towards the silicon substrates, X-ray photoelectron spectroscopy analyses have been carried out.

  12. CdSe quantum dots synthesized by laser ablation in water and their photovoltaic applications

    NASA Astrophysics Data System (ADS)

    Horoz, Sabit; Lu, Liyou; Dai, Qilin; Chen, Jiajun; Yakami, Baichhabi; Pikal, J. M.; Wang, Wenyong; Tang, Jinke

    2012-11-01

    CdSe quantum dots (QDs) have been prepared by a facile and clean synthesis method--laser ablation in water. The structural and luminescent properties of the CdSe QDs have been investigated. The CdSe QDs of wurtzite crystal structure have an average particle size of about 5 nm. The QDs can be attached to ZnO nanowires making them ideal for applications in QD-sensitized nanowire solar cells. A uniqueness of the QDs attached to the ZnO nanowires by this laser ablation method is that they do not contain ligands, and the preparation avoids the complicated process of ligand exchange.

  13. Experimental and Analytical Investigation of Cemented Tungsten Carbide Ultra-Short Pulse Laser Ablation

    NASA Astrophysics Data System (ADS)

    Urbina, J. P. Calderón; Daniel, C.; Emmelmann, C.

    Ultra-short pulse laser processing of hard materials, such as cemented tungsten carbide, requires an accurate and agile experimental and analytical investigation to obtain adequate information and setting parameters to maximize ablation rate. Therefore, this study presents a systematic approach which, first, experimentally searches for the variables with the most significant influence on the objective using a design of experiments method; and second, analyzes by means of existing ablation theory the interaction of the material and laser taking into account the Beer-Lambert law and incubation effect.Therefore, this places a basis for future analytical-experimental validation of the examined material.

  14. Ultrashort-pulse laser ablation of nanocrystalline aluminum

    SciTech Connect

    Gill-Comeau, Maxime; Lewis, Laurent J.

    2011-12-01

    Molecular-dynamics simulations of the ablation of nanocrystalline Al films by ultrashort laser pulses in the low-fluence (no-ionization) regime (0-2.5 times the ablation threshold, F{sub th}) are reported. The simulations employ an embedded-atom method potential for the dynamics of the ions and a realistic two-temperature model for the electron gas (and its interactions with the ion gas), which confers different electronic properties to the monocrystalline solid, nanocrystalline solid, and liquid regions of the targets. The ablation dynamics in three nanocrystalline structures is studied: two dense targets with different crystallite sizes (d=3.1 and 6.2 nm on average) and a d=6.2 nm porous sample. The results are compared to the ablation of monocrystalline Al. Significant differences are observed, the nanocrystalline targets showing, in particular, a lower ablation threshold and a larger melting depth, and yielding pressure waves of higher amplitude than the monocrystalline targets. Furthermore, it is shown that nanocrystalline targets experience no residual stress associated with thermal expansion and lateral constraints, and that little crystal growth occurs in the solid during and after ablation. Laser-induced spallation of the back surface of the films is also investigated; we find, in particular, that the high-strain fracture resistance of nanocrystalline samples is significantly reduced in comparison to the crystalline material.

  15. CO{sub 2} Laser Ablation Propulsion Tractor Beams

    SciTech Connect

    Sinko, John E.; Schlecht, Clifford A.

    2010-05-06

    Manipulation of objects at a distance has already been achieved with no small measure of success in the realm of microscopic objects on the scale size of nanometers to micrometers in applications including laser trapping and laser tweezers. However, there has been relatively little effort to apply such remote control to macroscopic systems. A space tractor beam could be applied to a wide range of applications, including removal of orbital debris, facilitation of spacecraft docking, adjustment of satellite attitude or orbital position, etc. In this paper, an ablative laser propulsion tractor beam is demonstrated based on radiation from a CO{sub 2} laser. Cooperative, layered polymer targets were used for remote impulse generation using a CO{sub 2} laser. The use of a structured ablatant enabling switching between thrust directional parity (i.e., forward or reverse) and imparting torque to a remote target. Fluence-dependent results are presented in the context of polymer ablation modeling work and with consideration of confined ablation effects.

  16. Infrared laser ablation sample transfer for MALDI imaging.

    PubMed

    Park, Sung-Gun; Murray, Kermit K

    2012-04-03

    An infrared laser was used to ablate material from tissue sections under ambient conditions for direct collection on a matrix assisted laser desorption ionization (MALDI) target. A 10 μm thick tissue sample was placed on a microscope slide and was mounted tissue-side down between 70 and 450 μm from a second microscope slide. The two slides were mounted on a translation stage, and the tissue was scanned in two dimensions under a focused mid-infrared (IR) laser beam to transfer material to the target slide via ablation. After the material was transferred to the target slide, it was analyzed using MALDI imaging using a tandem time-of-flight mass spectrometer. Images were obtained from peptide standards for initial optimization of the system and from mouse brain tissue sections using deposition either onto a matrix precoated target or with matrix addition after sample transfer and compared with those from standard MALDI mass spectrometry imaging. The spatial resolution of the transferred material is approximately 400 μm. Laser ablation sample transfer provides several new capabilities not possible with conventional MALDI imaging including (1) ambient sampling for MALDI imaging, (2) area to spot concentration of ablated material, (3) collection of material for multiple imaging analyses, and (4) direct collection onto nanostructure assisted laser desorption ionization (NALDI) targets without blotting or ultrathin sections.

  17. Femtosecond laser ablation of cadmium tungstate for scintillator arrays

    NASA Astrophysics Data System (ADS)

    Richards, S.; Baker, M. A.; Wilson, M. D.; Lohstroh, A.; Seller, P.

    2016-08-01

    Ultrafast pulsed laser ablation has been investigated as a technique to machine CdWO4 single crystal scintillator and segment it into small blocks with the aim of fabricating a 2D high energy X-ray imaging array. Cadmium tungstate (CdWO4) is a brittle transparent scintillator used for the detection of high energy X-rays and γ-rays. A 6 W Yb:KGW Pharos-SP pulsed laser of wavelength 1028 nm was used with a tuneable pulse duration of 10 ps to 190 fs, repetition rate of up to 600 kHz and pulse energies of up to 1 mJ was employed. The effect of varying the pulse duration, pulse energy, pulse overlap and scan pattern on the laser induced damage to the crystals was investigated. A pulse duration of ≥500 fs was found to induce substantial cracking in the material. The laser induced damage was minimised using the following operating parameters: a pulse duration of 190 fs, fluence of 15.3 J cm-2 and employing a serpentine scan pattern with a normalised pulse overlap of 0.8. The surface of the ablated surfaces was studied using scanning electron microscopy, energy dispersive X-ray spectroscopy, atomic force microscopy and X-ray photoelectron spectroscopy. Ablation products were found to contain cadmium tungstate together with different cadmium and tungsten oxides. These laser ablation products could be removed using an ammonium hydroxide treatment.

  18. Laser Ablation Surface Preparation of Ti-6A1-4V for Adhesive Bonding

    NASA Technical Reports Server (NTRS)

    Palmieri, Frank L.; Watson, Kent A.; Morales, Guillermo; Williams, Thomas; Hicks, Robert; Wohl, Christopher J.; Hopkins, John W.; Connell, John W.

    2012-01-01

    Adhesive bonding offers many advantages over mechanical fastening, but requires certification before it can be incorporated in primary structures for commercial aviation without disbond-arrestment features or redundant load paths. Surface preparation is widely recognized as the key step to producing robust and predictable bonds. Laser ablation imparts both topographical and chemical changes to a surface which can lead to increased bond durability. A laser based process provides an alternative to chemical-dip, manual abrasion and grit blast treatments which are expensive, hazardous, polluting, and less precise. This report documents preliminary testing of a surface preparation technique using laser ablation as a replacement for the chemical etch and abrasive processes currently applied to Ti-6Al-4V alloy adherends. Failure mode, surface roughness, and chemical makeup were analyzed using fluorescence enhanced visualization, microscopy, and X-ray photoelectron spectroscopy, respectively. Single lap shear tests were conducted on bonded and aged specimens to observe bond strength retention and failure mode. Some promising results showed increasing strength and durability of lap shear specimens as laser ablation coverage area and beam intensity increased. Chemical analyses showed trends for surface chemical species which correlated with improved bond strength and durability. Combined, these results suggest that laser ablation is a viable process for inclusion with or/and replacement of one or more currently used titanium surface treatments. On-going work will focus on additional mechanical tests to further demonstrate improved bond durability.

  19. Investigations of the damage mechanisms during ultrashort pulse laser ablation of dental tissue

    NASA Astrophysics Data System (ADS)

    Domke, Matthias; Wick, Sebastian; Laible, Maike; Rapp, Stephan; Kuznetsova, Julia; Homann, Christian; Huber, Heinz P.; Sroka, Ronald

    2015-07-01

    Several investigations of dental tissue ablation with ultrashort pulsed lasers suggest that these lasers enable precise and selective material removal and reduce the formation of micro cracks and thermal effects, when compared to ns-pulses. In this study, two damage mechanisms are presented occurring during ablation of dentin using a laser emitting pulses of a duration of 380 fs at a wavelength of 1040 nm. First, it was found that nano cracks appear around the craters after single fs-pulse ablation. These cracks are directed to the crater and cross the dentinal tubules. Transient investigation of the single fs-pulse ablation process by pump-probe microscopy suggest that the driving mechanism could be a pressure wave that is released after stress confinement. Second, squared ablation holes were created by moving the laser focus at scan speeds between 0.5 mm/s and 2.0 m/s and fluences up to 14 J/cm2. It was found that deep cracks appear at the edges of the squared holes, if the scan speed is about 0.5 m/s. The fluence has only a minor impact on the crack formation. The crack propagation was investigated in the depth using x-ray micro tomography and optical coherence tomography. It was found that these cracks appear in the depth down to the dental pulp. These findings suggest that fast scanning of the laser beam is the key for damage free processing using ultrashort pulse lasers. Then, ablation rates of about 2.5 - 3.5 mm3/min/W can be achieved in dentine with pulse durations of 380 fs.

  20. Laser-induced ablation of polymers using a patterned dopant generated from a leuco-dye precursor via flood exposure: A ``portable conformable mask'' approach to laser ablation of PMMA at 351 nm

    NASA Astrophysics Data System (ADS)

    Holtz, S.; Bargon, J.

    1995-05-01

    A two-stage laser ablation process is described, which initially generates a laser-light absorbing image from a conventional photolithographic mask via a UV-flood exposure step. For this purpose a colorless precursor of a dye, i.e., its leuco form, is imbedded into the polymer to be ablated as a dopant. For poly(methyl methacrylate) as such a polymer, triphenylmethanol, the leuco precursor for the corresponding triphenylmethyl dye represents a good choice for ablation with excimer lasers operating at the wavelength 351 nm. In this fashion conventional masks and exposure tools of UV-photolithography may be used in combination with laser ablation. The resulting images are characterized by a good contrast and reasonably sharp contours. The photochemical mechanism and additional aspects of this two-step process, which resembles the “portable conformal mask” approach of photolithography, are outlined.

  1. Absorption-ablation-excitation mechanism of laser-cluster interactions in a nanoaerosol system.

    PubMed

    Ren, Yihua; Li, Shuiqing; Zhang, Yiyang; Tse, Stephen D; Long, Marshall B

    2015-03-06

    The absorption-ablation-excitation mechanism in laser-cluster interactions is investigated by measuring Rayleigh scattering of aerosol clusters along with atomic emission from phase-selective laser-induced breakdown spectroscopy. For 532 nm excitation, as the laser intensity increases beyond 0.16  GW/cm^{2}, the scattering cross section of TiO_{2} clusters begins to decrease, concurrent with the onset of atomic emission of Ti, indicating a scattering-to-ablation transition and the formation of nanoplasmas. With 1064 nm laser excitation, the atomic emissions are more than one order of magnitude weaker than that at 532 nm, indicating that the thermal effect is not the main mechanism. To better clarify the process, time-resolved measurements of scattering signals are examined for different excitation laser intensities. For increasing laser intensity, the cross section of clusters decreases during a single pulse, evincing the shorter ablation delay time and larger ratios of ablation clusters. Assessment of the electron energy distribution during the ablation process is conducted by nondimensionalizing the Fokker-Planck equation, with analogous Strouhal Sl_{E}, Peclet Pe_{E}, and Damköhler Da_{E} numbers defined to characterize the laser-induced aerothermochemical environment. For conditions where Sl_{E}≫1, Pe_{E}≫1, and Da_{E}≪1, the electrons are excited to the conduction band by two-photon absorption, then relax to the bottom of the conduction band by electron energy loss to the lattice, and finally serve as the energy transfer media between laser field and lattice. The relationship between delay time and excitation intensity is well correlated by this simplified model with quasisteady assumption.

  2. Optical design and laser ablation of surface textures: demonstrating total internal reflection

    NASA Astrophysics Data System (ADS)

    Gommans, Hans; Booij, Silvia; Pijlman, Fetze; Krijn, Marcel; de Zwart, Siebe; Sepkhanov, Ruslan; Beaumont, Dave; van der Schaft, Hans; Sanders, Rene

    2015-09-01

    In lighting applications key drivers for optical design of surface textures are integration of optical elements, the disentanglement of optical functionality and appearance and late stage configuration. We investigated excimer laser ablation as a mastering technology for micro textured surfaces, where we targeted an increase in correspondence between surface design and ablated surface for high aspect ratio structures. To achieve this we have improved the photo mask design using a heuristic algorithm that corrects for the angular dependence of the ablation process and the loss of image resolution at ablation depths that exceed the depth of field. Using this approach we have been able to demonstrate close correspondence between designed and ablated facet structures up to 75° inclination at 75 μm depth. These facet design parameters allow for total internal reflection (TIR) as a means of beam deflection which is demonstrated in a range of mono shaped cone arrays in hexagonal tessellation. BSDF analysis was used to characterize the narrow TIR deflection beams that matched the peak positions of the design down to 28° apex. In addition, a single surface TIR-Fresnel lens design with focal distance 5 mm has been manufactured using this photo mask design algorithm and beam collimation up to 12° beam angle and 32° field angle is shown. These outcomes demonstrate that the laser ablation process intrinsically yields sufficient small dispersion in structure and fillet radii for lighting applications.

  3. Production of nanoparticles from natural hydroxylapatite by laser ablation

    PubMed Central

    2011-01-01

    Laser ablation of solids in liquids technique has been used to obtain colloidal nanoparticles from biological hydroxylapatite using pulsed as well as a continuous wave (CW) laser. Transmission electron microscopy (TEM) measurements revealed the formation of spherical particles with size distribution ranging from few nanometers to hundred nanometers and irregular submicronic particles. High resolution TEM showed that particles obtained by the use of pulsed laser were crystalline, while those obtained by the use of CW laser were amorphous. The shape and size of particles are consistent with the explosive ejection as formation mechanism. PMID:21711800

  4. Development of a Laser Ablation ICPMS Rutile Standard

    NASA Astrophysics Data System (ADS)

    Lytle, M. L.; Kohn, M. J.

    2015-12-01

    Rutile is a common accessory mineral in igneous and high-grade metamorphic rocks and igneous, with many applications in geosciences. Rutile geochemistry, especially the high field strength elements (i.e., Nb and Ta), monitors many geological processes including subduction-zone metamorphism, while Zr provides temperature information in buffering assemblages. Rutile can also be used for U-Pb geochronology, but typically low U concentrations can make age dating difficult. Many applications of rutile now rely on laser ablation ICPMS (LA-ICPMS) analysis, a major disadvantage of this technique is the lack of reliable rutile standards. Here, we present laser ablation data of several rutile megacrysts from around the world, illustrating typical geochemical characteristics of potential standards. Whole-grain transects and depth profiles were collected on several rutiles, including Graves Mountain, Kragerø, Madagascar, Mozambique, Quebec, and Diamantina. Most transects, particularly across Graves Mountain and Diamantina, show dramatic zoning in Zr (up to 100 ppm), U (up to 10 ppm), and Nb (up to 1000 ppm). Rutile grains from Mozambique and Kragerø show little variation in concentration in Zr, U, and Nb. However, U concentrations generally range from 1ppm (Graves Mountain) to 45ppm (Kragero). Depth profiles (30-80s analysis; 15-40 μm) showed a combination of slight surface contamination plus minor to significant near-rim zoning. Some samples, such as Mozambique, show minor concentration changes in Zr, Nb, and Ta over the outer 10 μm but are otherwise unzoned, whereas U concentrations decrease for 25 μm then are constant. Kragero shows depth zoning throughout for Zr, Ta, and U but Nb is unzoned. Some rutile megacrysts show promise as standards (e.g. Mozambique and Kragero), but must be prepared to eliminate crystal surfaces. Other megacrysts would have to be subsampled within specific crystals to isolate chemical homogeneous domains.

  5. Optical properties of petal-like aggregated nanocrystalline zinc oxide synthesized by laser ablation

    SciTech Connect

    Jafarkhani, P.; Chehrghani, A.; Torkamany, M.J.

    2012-03-15

    Highlights: Black-Right-Pointing-Pointer Petal like ZnO nanocrystals are synthesized by high frequency laser ablation in water. Black-Right-Pointing-Pointer Optical band gap of ZnO nanocrystals was tunable by changing the laser pulse energy. Black-Right-Pointing-Pointer Nonlinear optical properties and limiting threshold were obtained by Z-scan technique. -- Abstract: The results of the investigations carried out on the third-order nonlinearity in zinc oxide (ZnO) nanocrystals (NCs) by Z-scan technique are included in this paper. ZnO NCs show negative nonlinearity and good nonlinear absorption behavior at 532 nm. The third-order optical susceptibility {chi}(3) increases with enlargement of NCs due to the size dependent enhancement of exciton oscillator strength. The synthesis of ZnO NCs was performed by laser ablation from a high-purity metallic target of Zn in distilled water medium. For the ablation process, a high frequency pulsed Nd:YAG laser was employed operating at 532 nm with 100 ns pulse duration. UV-vis absorption spectroscopy illustrated the enhancement of the size of ZnO NCs upon increasing the laser pulse energy applied in ablation process. Accordingly the corresponding optical band gap (E{sub g}) decrease by increasing the size of NCs. X-ray diffraction (XRD) associated with transmission electron microscopy (TEM) was utilized to characterize the crystalline phase and also for determining the ZnO NCs morphology.

  6. Infrared Laser Ablation Sample Transfer for MALDI and Electrospray

    NASA Astrophysics Data System (ADS)

    Park, Sung-Gun; Murray, Kermit King

    2011-08-01

    We have used an infrared laser to ablate materials under ambient conditions that were captured in solvent droplets. The droplets were either deposited on a MALDI target for off-line analysis by MALDI time-of-flight mass spectrometry or flow-injected into a nanoelectrospray source of an ion trap mass spectrometer. An infrared optical parametric oscillator (OPO) laser system at 2.94 μm wavelength and approximately 1 mJ pulse energy was focused onto samples for ablation at atmospheric pressure. The ablated material was captured in a solvent droplet 1-2 mm in diameter that was suspended from a silica capillary a few millimeters above the sample target. Once the sample was transferred to the droplet by ablation, the droplet was deposited on a MALDI target. A saturated matrix solution was added to the deposited sample, or in some cases, the suspended capture droplet contained the matrix. Peptide and protein standards were used to assess the effects of the number of IR laser ablation shots, sample to droplet distance, capture droplet size, droplet solvent, and laser pulse energy. Droplet collected samples were also injected into a nanoelectrospray source of an ion trap mass spectrometer with a 500 nL injection loop. It is estimated that pmol quantities of material were transferred to the droplet with an efficiency of approximately 1%. The direct analysis of biological fluids for off-line MALDI and electrospray was demonstrated with blood, milk, and egg. The implications of this IR ablation sample transfer approach for ambient imaging are discussed.

  7. Optimization of silver nanoparticles production by laser ablation in water using a 150-ps laser

    NASA Astrophysics Data System (ADS)

    Stašić, J.; Živković, Lj.; Trtica, M.

    2016-12-01

    Silver nanoparticles were synthesized by laser ablation in liquid (water) using a 150-ps Nd:YAG laser. Due to their extraordinary characteristics, especially when obtained by this method providing high purity and high stability of colloids, silver NPs are nowadays highly important in various applications. The objective of this study was to optimize the process parameters in order to achieve the highest possible yield while retaining small particle size. Yield/mass concentration of the obtained particles was measured depending on different parameters: time of irradiation, pulse energy, position regarding the focus, and number of irradiation locations. The conditions providing relatively high yield, small particle size, highest production rate, and highest efficiency are 7 mJ, 15-min irradiation time (9000 pulses), and target position ˜4 mm in front of the lens focus. The results are compared with the results obtained by the longer nanosecond as well as the ultrashort pulsed lasers. A possible physical explanation is given.

  8. Laser ablation assisted adhesive bonding of automotive structural composites

    SciTech Connect

    Boeman, R.G.; Paulauskas, F.L.; Warren, C.D.

    1999-07-03

    Laser ablation has been evaluated as a surface pretreatment prior to adhesive bonding. In prior experimental work, it was observed that when adhesively bonded, composite, single lap shear samples fail, the fracture often occurs at either the adhesive/adherend interface or in the resin rich surface layer of the composite. These two areas represent the weakest portion of the joint. Laser ablation pretreatment generates areas where the resin on the composite surface is selectively removed leaving behind exposed reinforcing fibers which are the major load bearing members of the composite. In a subsequent adhesive bonding operation, this allows portions of the fibers to be encapsulated in the adhesive while other portions of the fiber remain in the composite resin. This type of pretreatment permits fibers to bridge and reinforce the interface between adhesive and adherend. A secondary benefit is the removal of surface contaminantes by pyrolysis. Microscopic observation of laser ablated surfaces indicates a prominent, fiber rich area. Results of the mechanical evaluation indicated that the lap shear strength for laser ablated samples was significantly higher than specimens with no pretreatment or with solvent cleaning only, but were slightly lower than specimens that were mechanically roughened and cleaned with solvents prior to bonding.

  9. Pulsed laser ablation of pepsin on an inorganic substrate

    NASA Astrophysics Data System (ADS)

    Cicco, N.; Lopizzo, T.; Marotta, V.; Morone, A.; Verrastro, M.; Viggiano, V.

    2009-03-01

    Pressed pepsin pellets used as targets were ablated with the pulses of the Nd-YAG laser. The activity of the pepsin thin layer, deposited on a glass substrate, was successfully detected by analyzing the proteolytic degradation areas on the polyacrylamide gel (PA-gel) copolymerized with albumin from the hen egg white (ovalbumin), used as an enzymatic substrate.

  10. Femtosecond laser ablation of gold interdigitated electrodes for electronic tongues

    NASA Astrophysics Data System (ADS)

    Manzoli, Alexandra; de Almeida, Gustavo F. B.; Filho, José A.; Mattoso, Luiz H. C.; Riul, Antonio; Mendonca, Cleber R.; Correa, Daniel S.

    2015-06-01

    Electronic tongue (e-tongue) sensors based on impedance spectroscopy have emerged as a potential technology to evaluate the quality and chemical composition of food, beverages, and pharmaceuticals. E-tongues usually employ transducers based on metal interdigitated electrodes (IDEs) coated with a thin layer of an active material, which is capable of interacting chemically with several types of analytes. IDEs are usually produced by photolithographic methods, which are time-consuming and costly, therefore, new fabrication technologies are required to make it more affordable. Here, we employed femtosecond laser ablation with pulse duration of 50 fs to microfabricate gold IDEs having finger width from 2.3 μm up to 3.2 μm. The parameters used in the laser ablation technique, such as light intensity, scan speed and beam spot size have been optimized to achieve uniform IDEs, which were characterized by optical and scanning electron microscopy. The electrical properties of gold IDEs fabricated by laser ablation were evaluated by impedance spectroscopy, and compared to those produced by conventional photolithography. The results show that femtosecond laser ablation is a promising alternative to conventional photolithography for fabricating metal IDEs for e-tongue systems.

  11. Laser Ablation of Materials for Propulsion of Spacecraft

    NASA Technical Reports Server (NTRS)

    Edwards, David L.; Carruth, Ralph; Campbell, Jonathan; Gray, Perry

    2004-01-01

    A report describes experiments performed as part of a continuing investigation of the feasibility of laser ablation of materials as a means of propulsion for small spacecraft. In each experiment, a specimen of ablative material was mounted on a torsion pendulum and irradiated with a laser pulse having an energy of 5 J. The amplitude of the resulting rotation of the torsion pendulum was taken to be an indication of the momentum transferred from the laser beam. Of the ablative materials tested, aluminum foils yielded the smallest rotation amplitudes of the order of 10 degrees. Black coating materials yielded rotation amplitudes of the order of 90 degrees. Samples of silver coated with a fluorinated ethylene propylene (FEP) copolymer yielded the largest rotation amplitudes 6 to 8 full revolutions. The report presents a theory involving heating of a confined plasma followed by escape of the plasma to explain the superior momentum transfer performance of the FEP specimens. It briefly discusses some concepts for optimizing designs of spacecraft engines to maximize the thrust obtainable by exploiting the physical mechanisms of the theory. Also discussed is the use of laser-ablation engines with other types of spacecraft engines.

  12. Estimation of Al2O3 critical temperature using a Langmuir probe in laser ablation

    NASA Astrophysics Data System (ADS)

    Yahiaoui, K.; Abdelli-Messaci, S.; Messaoud Aberkane, S.; Kellou, A.

    2016-11-01

    Pulsed laser deposition (PLD) has demonstrated its capacity in thin films growing under the moderate laser intensity. But when the laser intensity increases, the presence of droplets on the thin film limits the PLD efficiency such that the process needs an optimization study. In this way, an experimental study has been conducted in order to correlate between the appearance of those droplets and the laser fluence. The comprehension of the physical mechanism during ablation and the control of the deposition parameters allowed to get a safe process. Our experiment consists in measuring the amount of ejected matter from polycrystalline alumina target as a function of the laser fluence when irradiated by a KrF laser. According to laser fluence, several kinds of ablation regimes have been identified. Below a threshold value found as 12 J/cm2, the mechanism of ablation was assigned to normal evaporation, desorption and nonthermal processes. While above this threshold value, the mechanism of ablation was assigned to phase explosion phenomenon which is responsible of droplets formation when the surface temperature approaches the critical temperature T tc. A negative charge collector was used to collect the positive ions in the plume. Their times of flight (TOF) signal were used to estimate the appropriate T tc for alumina target. Ions yield, current as well as kinetic energy were deduced from the TOF signal. Their evolutions show the occurrence of an optical breakdown in the vapor plume which is well correlated with the onset of the phase explosion phenomenon. At 10 J/cm2, the ions velocities collected by the probe have been compared to those obtained from optical emission spectroscopy diagnostic and were discussed. To prove the occurrence of phase explosion by the appearance of droplets, several thin films were elaborated on Si (100) substrate at different laser fluence into vacuum. They have been characterized by scanning electron microscope. The results were well

  13. Optical transmission and laser ablation of pathologically changed eye lens capsule

    NASA Astrophysics Data System (ADS)

    Gamidov, A. A.; Bolshunov, A. V.; Yuzhakov, A. V.; Shcherbakov, E. M.; Baum, O. I.; Sobol, E. N.

    2015-02-01

    Optical transmission and ablation mechanisms in the secondary cataract films under the impact of 1.06-mm laser radiation are studied. The comparison of incident and transmitted (paraxial) radiation power at different values of the power density is carried out for two types of the eye lens capsule tissue (hard and soft) possessing different optical and mechanical properties. It is found that the effective attenuation coefficient for soft films is almost five times as large as that for the hard ones. The obtained measurement data on the transparency variation in the process of laser action allow the temperature evaluation and the determination of dominant mechanism of laser ablation, as well as the development of recommendations, providing the prevention or reduction of possible side effects. The obtained results can be used to optimise the regimes of laser impact in the process of the opacified lens capsule removal.

  14. Optical transmission and laser ablation of pathologically changed eye lens capsule

    SciTech Connect

    Gamidov, A A; Bolshunov, A V; Yuzhakov, A V; Shcherbakov, E M; Baum, O I; Sobol, E N

    2015-02-28

    Optical transmission and ablation mechanisms in the secondary cataract films under the impact of 1.06-mm laser radiation are studied. The comparison of incident and transmitted (paraxial) radiation power at different values of the power density is carried out for two types of the eye lens capsule tissue (hard and soft) possessing different optical and mechanical properties. It is found that the effective attenuation coefficient for soft films is almost five times as large as that for the hard ones. The obtained measurement data on the transparency variation in the process of laser action allow the temperature evaluation and the determination of dominant mechanism of laser ablation, as well as the development of recommendations, providing the prevention or reduction of possible side effects. The obtained results can be used to optimise the regimes of laser impact in the process of the opacified lens capsule removal.

  15. Hybrid Laser Processing of Transparent Materials

    NASA Astrophysics Data System (ADS)

    Niino, Hiroyuki

    The following chapter is an overview of processing fused silica and other transparent materials by pulsed-laser irradiation: (1) Direct excitation of materials with multi-wavelength excitation processes, and (2) Media-assisted process with a conventional pulsed laser. A method to etch transparent materials by using laserinduced plasma-assisted ablation (LIPAA), or laser-induced backside wet etching (LIBWE), has been described in detail.

  16. Setup for functional cell ablation with lasers: coupling of a laser to a microscope.

    PubMed

    Sweeney, Sean T; Hidalgo, Alicia; de Belle, J Steven; Keshishian, Haig

    2012-06-01

    The selective removal of cells by ablation is a powerful tool in the study of eukaryotic developmental biology, providing much information about their origin, fate, or function in the developing organism. In Drosophila, three main methods have been used to ablate cells: chemical, genetic, and laser ablation. Each method has its own applicability with regard to developmental stage and the cells to be ablated, and its own limitations. The primary advantage of laser-based ablation is the flexibility provided by the method: The operations can be performed in any cell pattern and at any time in development. Laser-based techniques permit manipulation of structures within cells, even to the molecular level. They can also be used for gene activation. However, laser ablation can be expensive, labor-intensive, and time-consuming. Although live cells can be difficult to image in Drosophila embryos, the use of vital fluorescent imaging methods has made laser-mediated cell manipulation methods more appealing; the methods are relatively straightforward. This article provides the information necessary for setting up and using a laser microscope for lasesr ablation studies.

  17. Comparative study on laser tissue ablation between PV and HPS lasers

    NASA Astrophysics Data System (ADS)

    Kang, Hyun Wook; Jebens, David; Mitchell, Gerald; Koullick, Ed

    2008-02-01

    Laser therapy for obstructive benign prostatic hyperplasia (BPH) has gained broad adoption due to effective tissue removal, immediate hemostasis, and minor complications. The aim of this study is to quantitatively compare ablation characteristics of PV (Photoselective Vaporization) and the newly introduced HPS (High Performance System) 532 nm lasers. Bovine prostatic tissues were ablated in vitro, using a custom-made scanning system. Laser-induced volume produced by two lasers was quantified as a function of applied power, fiber working distance (WD), and treatment speed. Given the same power of 80 W and speed of 4 mm/s, HPS created up to 50 % higher tissue ablation volume than PV did. PV induced a rapid decrease of ablation volume when WD increased from 0.5 mm to 3 mm while HPS yielded almost constant tissue removal up to 3 mm for both 80 W and 120 W. As the treatment speed increased, both lasers reached saturation in tissue ablation volume. Lastly, both PV and HPS lasers exhibited approximately 1 mm thick heat affected zone (HAZ) in this study although HPS created twice deeper ablation channels with a depth of up to 4 mm. Due to a smaller beam size and a higher output power, HPS maximized tissue ablation rate with minimal thermal effects to the adjacent tissue. Furthermore, more collimated beam characteristics provides more spatial flexibility and may even help to decrease the rate of fiber degradation associated with thermal damage from debris reattachment to the tip.

  18. In-Situ Apatite Laser Ablation U-Th-Sm/He Dating, Methods and Challenges

    NASA Astrophysics Data System (ADS)

    Pickering, J. E.; Matthews, W.; Guest, B.; Hamilton, B.; Sykes, C.

    2015-12-01

    In-situ, laser ablation U-Th-Sm/He dating is an emerging technique in thermochronology that has been proven as a means to date zircon and monzonite1-5. In-situ U-Th-Sm/He thermochronology eliminates many of the problems and inconveniences associated with traditional, whole grain methods, including; reducing bias in grain selection based on size, shape and clarity; allowing for the use of broken grains and grains with inclusions; avoiding bad neighbour effects; and eliminating safety hazards associated with dissolution. In-situ apatite laser ablation is challenging due to low concentrations of U and Th and thus a low abundance of radiogenic He. For apatite laser ablation to be effective the ultra-high-vacuum (UHV) line must have very low and consistent background levels of He. To reduce He background, samples are mounted in a UHV stable medium. Our mounting process uses a MicroHePP (Microscope Mounted Heated Platen Press) to press samples into FEP (fluorinated ethylene propylene) bonded to an aluminum backing plate. Samples are ablated using a Resonetics 193 nm excimer laser and liberated He is measured using a quadrupole mass spectrometer on the ASI Alphachron noble gas line; collectively this system is known as the Resochron. The ablated sites are imaged using a Zygo Zescope optical profilometer and ablated pit volume measured using PitVol, a custom MatLab algorithm developed to enable precise and unbiased measurement of the ablated pit geometry. We use the well-characterized Durango apatite to demonstrate the accuracy and precision of the method. He liberated from forty-two pits, having volumes between 1700 and 9000 um3, were measured using the Resochron. The ablated sites were imaged using a Zygo Zescope optical profilometer and ablated pit volume measured using PitVol. U, Th and Sm concentrations were measured by laser ablation and the U-Th-Sm/He age calculated by standard age equation. An age of 33.8±0.31 Ma was determined and compares well with conventional

  19. Comparative shock wave analysis during corneal ablation with an excimer laser, picosecond laser, and femtosecond laser

    NASA Astrophysics Data System (ADS)

    Krueger, Ronald R.; Juhasz, Tibor

    1995-05-01

    With the event of topographic steep central islands following excimer laser surgery and the potential damage to the corneal endothelium, shock waves are playing an increasingly important role in laser refractive surgery. With this in mind, we performed a comparative shock wave analysis in corneal tissue using an excimer laser, picosecond laser, and femtosecond laser. We used a Lambda Physik excimer laser at 308 nm wavelength, a Nd:YLF picosecond laser at 1053 nm wavelength and a synchronously pumped linear cavity femtosecond laser at 630 nm wavelength. The pulse widths of the corresponding lasers were 8 ns, 18 ps, 150 fs, respectively. The energy density of irradiation was 2.5 to 8 times the threshold level being 2 J/cm2 (excimer laser), 86 J/cm2 (picosecond laser) and 10.3 J/cm2 (femtosecond laser). Shock wave dynamics were analyzed using time-resolved photography on a nanosecond time scale using the picosecond laser in corneal tissue, water and air. Shock wave dynamics using the femtosecond laser were studied in water only while the excimer laser induced shock wave during corneal ablation was studied in air only. We found the dynamics of shock waves to be similar in water and corneal tissue indicating that water is a good model to investigate shock wave effects in the cornea. The magnitude of the shock wave velocity and pressure decays over time to that of a sound wave. The distance over which it decays is 3 mm in air with the excimer laser and 600 - 700 micrometers in air with the picosecond laser. In water, the picosecond laser shock wave decays over a distance of 150 micrometers compared to the femtosecond laser shock wave which decays over a distance of 30 micrometers . Overall the excimer laser shock wave propagates 5 times further than that of the picosecond laser and the picosecond laser shock wave propagates 5 times further than that of the femtosecond laser. In this preliminary comparison, the time and distance for shock wave decay appears to be directly

  20. A review of Thulium fiber laser ablation of kidney stones

    NASA Astrophysics Data System (ADS)

    Fried, Nathaniel M.; Blackmon, Richard L.; Irby, Pierce B.

    2011-02-01

    The clinical solid-state Holmium:YAG laser lithotripter (λ=2120 nm) is capable of operating at high pulse energies, but its efficient operation is limited to low pulse rates during lithotripsy. The diode-pumped experimental Thulium Fiber Laser (λ=1908 nm) is limited to low pulse energies, but can operate at high pulse rates. This review compares stone ablation threshold, ablation rate, and retropulsion effects for Ho:YAG and TFL. Laser lithotripsy complications also include optical fiber bending failure resulting in endoscope damage and low irrigation rates leading to poor visibility. Both problems are related to fiber diameter and limited by Ho:YAG laser multimode spatial beam profile. This study exploits TFL spatial beam profile for higher power transmission through smaller fibers. A short taper is also studied for expanding TFL beam at the distal tip of a small-core fiber. Stone mass loss, stone crater depths, fiber transmission losses, fiber burn-back, irrigation rates, and deflection through a flexible ureteroscope were measured for tapered fiber and compared with conventional fibers. The stone ablation threshold for TFL was four times lower than for Ho:YAG. Stone retropulsion with Ho:YAG increased linearly with pulse energy. Retropulsion with TFL was minimal at pulse rates < 150 Hz, then rapidly increased at higher pulse rates. TFL beam profile provides higher laser power through smaller fibers than Ho:YAG laser, potentially reducing fiber failure and endoscope damage and allowing greater irrigation rates for improved visibility and safety. Use of a short tapered distal fiber tip also allows expansion of the laser beam, resulting in decreased fiber tip damage compared to conventional fibers, without compromising fiber bending, stone ablation efficiency, or irrigation rates.

  1. Controlled Contamination of Epoxy Composites with PDMS and Removal by Laser Ablation

    NASA Technical Reports Server (NTRS)

    Palmieri, Frank; Ledesma, Rodolfo; Cataldo, Daniel; Lin, Yi; Wohl, Christopher; Gupta, Mool; Connell, John

    2016-01-01

    Surface preparation is critical to the performance of adhesively bonded composites. During manufacturing, minute quantities of mold release compounds are inevitably deposited on faying surfaces and may compromise bond performance. To ensure safety, mechanical fasteners and other crack arrest features must be installed in the bondlines of primary structures, which negates some advantages of adhesively bonded construction. Laser ablation is an automated, repeatable, and scalable process with high potential for the surface preparation of metals and composites in critical applications such as primary airframe structures. In this study, laser ablation is evaluated on composite surfaces for the removal of polydimethylsiloxane (PDMS), a common mold release material. Composite panels were contaminated uniformly with PDMS film thicknesses as low as 6.0 nm as measured by variable angle spectroscopic ellipsometry. Bond performance was assessed by mechanical testing using a 250 F cure, epoxy adhesive and compared with pre-bond surface inspection results. Water contact angle, optically stimulated electron emission, and laser induced breakdown spectroscopy were used to characterize contaminated and laser ablated surfaces. The failure mode obtained from double cantilever beam tests correlated well with surface characterization data. The test results indicated that even low levels of PDMS were not completely removed by laser ablation.

  2. Preparation of GaN Nanostructures by Laser Ablation of ga Metal

    NASA Astrophysics Data System (ADS)

    El Nadi, Lotfia; Omar, Magdy M.; Mehena, Galila A.; Moniem, Hussien M. A.

    2011-06-01

    In the present study, GaN nanodots (0D) and nanowires (1D) nanostructures were prepared on stainless steal substrates applying laser ablation technique. The target of Ga metal mixed with NaNO2 was introduced in a central bore of a graphite rod of a confined geometry set up. The laser beam was normally focused onto the central bore and the ablated plume of Ga metal was deposited on stainless steal substrate lying below the graphite rod in an atmosphere of slow flow of nitrogen gas with or without ammonia vapor. The pulsed N2 laser beam having a wavelength of 337± 2 nm, pulse duration 15±1 ns and energy per pulse of 15±1 m J, could be focused on the central bore by a cylindrical quartz lens to a spot of dimensions 500 × 700 μm2 t providing target irradiance of 0.2-0.3 GW/cm2 per pulse. The ablated plum was collected after several thousand laser shots. The morphology and structure of the formed nanostructures were investigated by Scanning electron microscope and Energy Dispersive X-Ray Spectroscopy. The growth mechanism is most likely by Solid-Liquid-Vapor phase during the laser ablation processes. The role of the carbon, the NaNO2 and the flowing gas on the growth of Nanostructures of GaN are discussed.

  3. New Combined Laser Ablation Platform Determines Cell Wall Chemistry (Fact Sheet)

    SciTech Connect

    Not Available

    2011-09-01

    NREL has designed and developed a combined laser ablation/pulsed sample introduction/mass spectrometry platform that integrates pyrolysis and/or laser ablation with resonance-enhanced multiphoton ionization (REMPI) time-of-flight mass spectrometry. Using this apparatus, we can measure the cell wall chemical composition of untreated biomass materials. Understanding the chemical composition of untreated biomass is key to both the biochemical and thermochemical conversion of lignocellulosic biomass to biofuels. In the biochemical conversion process, the new technique provides a better understanding of the chemistry of lignin and will improve accessibility to plant sugars. In thermochemical conversion, the information provided by the new technique may help to reduce the formation of unwanted byproducts during gasification. NREL validated the ability of the system to detect pyrolysis products from plant materials using poplar, a potentially high-impact bioenergy feedstock. In the technique, biomass vapors are produced by laser ablation using the 3rd harmonic of an Nd:YAG laser (355 nm). The resulting vapors are entrained in a free jet expansion of helium, then skimmed and introduced into an ionization region. REMPI is used to ionize the vapors because it is highly sensitive for detecting lignin and aromatic metabolites. The laser ablation method was used to selectively volatilize specific plant tissues and detect lignin-based products from the vapors with enhanced sensitivity. This will allow the determination of lignin distribution in future biomass studies.

  4. Optical time of flight studies of lithium plasma in double pulse laser ablation: Evidence of inverse Bremsstrahlung absorption

    SciTech Connect

    Sivakumaran, V.; Joshi, H. C.; Singh, R. K.; Kumar, Ajai

    2014-06-15

    The early stage of formation of lithium plasma in a collinear—double pulse laser ablation mode has been studied using optical time of flight (OTOF) spectroscopy as a function of inter-pulse delay time, the distance from the target surface and the fluence of the ablation lasers. The experimental TOF measurements were carried out for lithium neutral (670.8 nm and 610.3 nm), and ionic (548.4 nm and 478.8 nm) lines. These experimental observations have been compared with that for single pulse laser ablation mode. It is found that depending on the fluence and laser pulse shape of the first pre-ablation laser and the second main ablation laser, the plasma plume formation and its characteristic features can be described in terms of plume-plume or laser-plume interaction processes. Moreover, the enhancement in the intensity of Li neutral and ionic lines is observed when the laser-plume interaction is the dominant process. Here, we see the evidence of the role of inverse Bremsstrahlung absorption process in the initial stage of formation of lithium plasma in this case.

  5. Fabrication of microchannels in single-crystal GaN by wet-chemical-assisted femtosecond-laser ablation

    NASA Astrophysics Data System (ADS)

    Nakashima, Seisuke; Sugioka, Koji; Midorikawa, Katsumi

    2009-09-01

    We investigated micro- and nano-fabrication of wide band-gap semiconductor gallium nitride (GaN) using a femtosecond (fs) laser. Nanoscale craters were successfully formed by wet-chemical-assisted fs-laser ablation, in which the laser beam is focused onto a single-crystal GaN substrate in a hydrochloric acid (HCl) solution. This allows efficient removal of ablation debris produced by chemical reactions during ablation, resulting in high-quality ablation. However, a two-step processing method involving irradiation by a fs-laser beam in air followed by wet etching, distorts the shape of the crater because of residual debris. The threshold fluence for wet-chemical-assisted fs-laser ablation is lower than that for fs-laser ablation in air, which is advantageous for improving fabrication resolution since it reduces thermal effects. We have fabricated craters as small as 510 nm by using a high numerical aperture (NA) objective lens with an NA of 0.73. Furthermore, we have formed three-dimensional hollow microchannels in GaN by fs-laser direct-writing in HCl solution.

  6. Optimisation of laser wavelength in the ablation sampling of glass materials

    NASA Astrophysics Data System (ADS)

    Shuttleworth, S.

    1996-04-01

    Glass is an excellent matrix for use in the immobilisation of waste materials. In order to more thoroughly understand how this material behaves over long periods of time it is important to be able to carry out spatially resolved chemical analysis of the material. One technique which offers spatially resolved chemical and isotopic analysis is laser microprobe inductively coupled plasma mass spectrometry. The laser is employed as a high resolution sampling probe and the inductively coupled plasma mass spectrometer provides the analysis. For the sampling technique to be valid it is imperative that the material ablated is representative of the original matrix. Unfortunately glass can be a difficult material to ablate at certain wavelengths due to its transparency and ability to reflect the radiation. This can result in ablation of material which is not representative of the matrix. This paper will examine the effect of laser wavelength on the ablation process. Chemical analysis by inductively coupled plasma mass spectrometry will be used to examine the composition of the ablate.

  7. Surface Modification of ICF Target Capsules by Pulsed Laser Ablation

    SciTech Connect

    Carlson, Lane C.; Johnson, Michael A.; Bunn, Thomas L.

    2016-06-30

    Topographical modifications of spherical surfaces are imprinted on National Ignition Facility (NIF) target capsules by extending the capabilities of a recently developed full surface (4π) laser ablation and mapping apparatus. The laser ablation method combines the precision, energy density and long reach of a focused laser beam to pre-impose sinusoidal modulations on the outside surface of High Density Carbon (HDC) capsules and the inside surface of Glow Discharge Polymer (GDP) capsules. Sinusoidal modulations described in this paper have sub-micron to 10’s of microns vertical scale and wavelengths as small as 30 μm and as large as 200 μm. The modulated patterns are created by rastering a focused laser fired at discrete capsule surface locations for a specified number of pulses. The computer program developed to create these raster patterns uses inputs such as laser beam intensity profile, the material removal function, the starting surface figure and the desired surface figure. The patterns are optimized to minimize surface roughness. Lastly, in this paper, simulated surfaces are compared with actual ablated surfaces measured using confocal microscopy.

  8. Surface Modification of ICF Target Capsules by Pulsed Laser Ablation

    DOE PAGES

    Carlson, Lane C.; Johnson, Michael A.; Bunn, Thomas L.

    2016-06-30

    Topographical modifications of spherical surfaces are imprinted on National Ignition Facility (NIF) target capsules by extending the capabilities of a recently developed full surface (4π) laser ablation and mapping apparatus. The laser ablation method combines the precision, energy density and long reach of a focused laser beam to pre-impose sinusoidal modulations on the outside surface of High Density Carbon (HDC) capsules and the inside surface of Glow Discharge Polymer (GDP) capsules. Sinusoidal modulations described in this paper have sub-micron to 10’s of microns vertical scale and wavelengths as small as 30 μm and as large as 200 μm. The modulatedmore » patterns are created by rastering a focused laser fired at discrete capsule surface locations for a specified number of pulses. The computer program developed to create these raster patterns uses inputs such as laser beam intensity profile, the material removal function, the starting surface figure and the desired surface figure. The patterns are optimized to minimize surface roughness. Lastly, in this paper, simulated surfaces are compared with actual ablated surfaces measured using confocal microscopy.« less

  9. Comparison of ultraviolet femtosecond and nanosecond laser ablation inductively coupled plasma mass spectrometry analysis in glass, monazite, and zircon.

    PubMed

    Poitrasson, Franck; Mao, Xianglei; Mao, Samuel S; Freydier, Rémi; Russo, Richard E

    2003-11-15

    We compared the analytical performance of ultraviolet femtosecond and nanosecond laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS). The benefit of ultrafast lasers was evaluated regarding thermal-induced chemical fractionation, that is otherwise well known to limit LA-ICPMS. Both lasers had a Gaussian beam energy profile and were tested using the same ablation system and ICPMS analyzer. Resulting crater morphologies and analytical signals showed more straightforward femtosecond laser ablation processes, with minimal thermal effects. Despite a less stable energy output, the ultrafast laser yielded elemental (Pb/U, Pb/Th) and Pb isotopic ratios that were more precise, repeatable, and accurate, even when compared to the best analytical conditions for the nanosecond laser. Measurements on NIST glasses, monazites, and zircon also showed that femtosecond LA-ICPMS calibration was less matrix-matched dependent and therefore more versatile.

  10. Laser processing of polytetrafluoroethylene (Teflon) in air

    NASA Astrophysics Data System (ADS)

    Wang, Z. B.; Hong, Ming Hui; Lu, Yong Feng; Chong, Tow Chong

    2003-02-01

    Teflon, polytetrafluorethylene (PTFE), is an important material in bioscience and medical application due to its special characteristics (non-flammable, anti-adhesive, heat-resistant and bio-compatible). The advantages of ultrashort laser processing of Teflon include a minimal thermal penetration region and low processing temperatures, precision removal of material, and good-quality feature definition. In this paper, laser processing of Teflon by Ti:Sapphire femtosecond laser (780 nm, 110 fs), Nd:YAG laser (532 nm, 7 ns) and CO2 laser (10.6 μm, 10 μs) has been investigated. For femtosecond laser processing, clear ablation takes place and provides high-quality groove on Teflon surface. Both the groove depth and the width increase as the laser fluence increase, and decrease almost linearly as the scanning speed increase for laser fluence below 5.0 J/cm2. For Nd:YAG processing, Teflon surface roughness is improved but no clean ablation is accessible, which makes it difficult to micromachine Teflon by Nd:YAG laser. For CO2 laser processing, laser-induced bumps were formed on Teflon surface with controlled laser parameters. The physics mechanisms for different pulse duration laser processing of Teflon are also discussed.

  11. Laser ablation of single-crystalline silicon by radiation of pulsed frequency-selective fiber laser

    NASA Astrophysics Data System (ADS)

    Veiko, V. P.; Skvortsov, A. M.; Huynh, C. T.; Petrov, A. A.

    2015-07-01

    We have studied the process of destruction of the surface of a single-crystalline silicon wafer scanned by the beam of a pulsed ytterbium-doped fiber laser radiation with a wavelength of λ = 1062 nm. It is established that the laser ablation can proceed without melting of silicon and the formation of a plasma plume. Under certain parameters of the process (radiation power, beam scan velocity, and beam overlap density), pronounced oxidation of silicon microparticles with the formation of a characteristic loose layer of fine powdered silicon dioxide has been observed for the first time. The range of lasing and beam scanning regimes in which the growth of SiO2 layer takes place is determined.

  12. Planar laser-driven ablation model for nonlocalized absorption

    SciTech Connect

    Dahmani, F.; Kerdja, T. )

    1991-05-01

    A model for planar laser-driven ablation is presented. Nonlocalized inverse bremsstrahlung absorption of laser energy at a density {ital n}{sub 1}{lt}{ital n}{sub {ital c}} is assumed. A steady-state solution in the conduction zone is joined to a rarefaction wave in the underdense plasma. The calculations relate all steady-state fluid quantities to only the material, absorbed intensity, and laser wavelength. The theory agrees well with results from a computer hydrodynamics code MEDUSA (Comput. Phys. Commun. {bold 7}, 271 (1974)) and experiments.

  13. Laser processing of solar cells with anti-reflective coating

    DOEpatents

    Harley, Gabriel; Smith, David D.; Dennis, Tim; Waldhauer, Ann; Kim, Taeseok; Cousins, Peter John

    2016-02-16

    Contact holes of solar cells are formed by laser ablation to accommodate various solar cell designs. Use of a laser to form the contact holes is facilitated by replacing films formed on the diffusion regions with a film that has substantially uniform thickness. Contact holes may be formed to deep diffusion regions to increase the laser ablation process margins. The laser configuration may be tailored to form contact holes through dielectric films of varying thicknesses.

  14. Ultra-fast Movies Resolve Ultra-short Pulse Laser Ablation and Bump Formation on Thin Molybdenum Films

    NASA Astrophysics Data System (ADS)

    Domke, Matthias; Rapp, Stephan; Huber, Heinz

    For the monolithic serial interconnection of CIS thin film solar cells, 470 nm molybdenum films on glass substrates must be separated galvanically. The single pulse ablation with a 660 fs laser at a wavelength of 1053 nm is investigated in a fluence regime from 0.5 to 5.0 J/cm2. At fluences above 2.0 J/cm2 bump and jet formation can be observed that could be used for creating microstructures. For the investigation of the underlying mechanisms of the laser ablation process itself as well as of the bump or jet formation, pump probe microscopy is utilized to resolve the transient ablation behavior.

  15. Real time ablation rate measurement during high aspect-ratio hole drilling with a 120-ps fiber laser.

    PubMed

    Mezzapesa, Francesco P; Sibillano, Teresa; Di Niso, Francesca; Ancona, Antonio; Lugarà, Pietro M; Dabbicco, Maurizio; Scamarcio, Gaetano

    2012-01-02

    We report on the instantaneous detection of the ablation rate as a function of depth during ultrafast microdrilling of metal targets. The displacement of the ablation front has been measured with a sub-wavelength resolution using an all-optical sensor based on the laser diode self-mixing interferometry. The time dependence of the laser ablation process within the depth of aluminum and stainless steel targets has been investigated to study the evolution of the material removal rate in high aspect-ratio micromachined holes.

  16. Time-resolved photoluminescence for evaluating laser-induced damage during dielectric stack ablation in silicon solar cells

    NASA Astrophysics Data System (ADS)

    Parola, Stéphanie; Blanc-Pélissier, Danièle; Barbos, Corina; Le Coz, Marine; Poulain, Gilles; Lemiti, Mustapha

    2016-06-01

    Selective laser ablation of dielectric layers on crystalline silicon wafers was investigated for solar cell fabrication. Laser processing was performed on Al2O3, and bi-layers Al2O3/SiNX:H with a nanosecond UV laser at various energy densities ranging from 0.4 to 2 J cm-2. Ablation threshold was correlated to the simulated temperature at the interface between the dielectric coatings and the silicon substrate. Laser-induced damage to the silicon substrate was evaluated by time-resolved photoluminescence. The minority carrier lifetime deduced from time-resolved photoluminescence was related to the depth of the heat affected zone in the substrate.

  17. Microsecond enamel ablation with 10.6μm CO2 laser radiation

    NASA Astrophysics Data System (ADS)

    Góra, W. S.; McDonald, A.; Hand, D. P.; Shephard, J. D.

    2016-02-01

    Lasers have been previously been used for dental applications, however there remain issues with thermally-induced cracking. In this paper we investigate the impact of pulse length on CO2 laser ablation of human dental enamel. Experiments were carried in vitro on molar teeth without any modification to the enamel surface, such as grinding or polishing. In addition to varying the pulse length, we also varied pulse energy and focal position, to determine the most efficient ablation of dental hard tissue and more importantly to minimize or eradicate cracking. The maximum temperature rise during the multi pulse ablation process was monitored using a set of thermocouples embedded into the pulpal chamber. The application of a laser device in dental surgery allows removal of tissue with higher precision, which results in minimal loss of healthy dental tissue. In this study we use an RF discharge excited CO2 laser operating at 10.6μm. The wavelength of 10.6 μm overlaps with a phosphate band (PO3-4) absorption in dental hard tissue hence the CO2 laser radiation has been selected as a potential source for modification of the tissue. This research describes an in-depth analysis of single pulse laser ablation. To determine the parameters that are best suited for the ablation of hard dental tissue without thermal cracking, a range of pulse lengths (10-200 μs), and fluences (0-100 J/cm2) are tested. In addition, different laser focusing approaches are investigated to select the most beneficial way of delivering laser radiation to the surface (divergent/convergent beam). To ensure that these processes do not increase the temperature above the critical threshold and cause the necrosis of the tissue a set of thermocouples was placed into the pulpal chambers. Intermittent laser radiation was investigated with and without application of a water spray to cool down the ablation site and the adjacent area. Results show that the temperature can be kept below the critical threshold

  18. Fast femtosecond laser ablation for efficient cutting of sintered alumina substrates

    NASA Astrophysics Data System (ADS)

    Oosterbeek, Reece N.; Ward, Thomas; Ashforth, Simon; Bodley, Owen; Rodda, Andrew E.; Simpson, M. Cather

    2016-09-01

    Fast, accurate cutting of technical ceramics is a significant technological challenge because of these materials' typical high mechanical strength and thermal resistance. Femtosecond pulsed lasers offer significant promise for meeting this challenge. Femtosecond pulses can machine nearly any material with small kerf and little to no collateral damage to the surrounding material. The main drawback to femtosecond laser machining of ceramics is slow processing speed. In this work we report on the improvement of femtosecond laser cutting of sintered alumina substrates through optimisation of laser processing parameters. The femtosecond laser ablation thresholds for sintered alumina were measured using the diagonal scan method. Incubation effects were found to fit a defect accumulation model, with Fth,1=6.0 J/cm2 (±0.3) and Fth,∞=2.5 J/cm2 (±0.2). The focal length and depth, laser power, number of passes, and material translation speed were optimised for ablation speed and high quality. Optimal conditions of 500 mW power, 100 mm focal length, 2000 μm/s material translation speed, with 14 passes, produced complete cutting of the alumina substrate at an overall processing speed of 143 μm/s - more than 4 times faster than the maximum reported overall processing speed previously achieved by Wang et al. [1]. This process significantly increases processing speeds of alumina substrates, thereby reducing costs, making femtosecond laser machining a more viable option for industrial users.

  19. Focused ion beam imaging of laser ablation sub-surface effects on layered materials

    NASA Astrophysics Data System (ADS)

    Téllez, Helena; Vadillo, José M.; Chater, Richard J.; Laserna, J. Javier; McPhail, David S.

    2008-12-01

    The focussed ion beam (FIB) represents a useful and versatile tool to allow visualization of sub-surface features related to the thermal effects of laser-target interaction with high spatial resolution. The possibility of performing a contamination-free milling process on specific sample locations provides significant advantage over conventional metallurgical procedures involving cutting and polishing. In particular, the direct visualization of the thermal features occurring at fluences below the phase explosion allows a deeper understanding of the extension of the laser heat-affected zone, the sub-surface alloying processes and additional features related to the photo-thermal mechanism of laser ablation.

  20. On the growth mechanism of nanoparticles in plasma during pulsed laser ablation in liquids

    NASA Astrophysics Data System (ADS)

    Taccogna, F.; Dell’Aglio, M.; Rutigliano, M.; Valenza, G.; De Giacomo, A.

    2017-04-01

    Particle-in-cell methodology is applied to study the simultaneous charging and coagulation of a nanoparticle, taking into account the self-consistent dynamics of surrounding plasma induced by laser ablation in liquid. The model uses, as an input, plasma temperature and electron number density which are experimentally obtained by high temporally resolved optical emission spectroscopy of the laser-induced plasma in water. Results show the important role of ions in the growth process and of the atom-induced evaporation process for the final nanoparticle size. The competition between different mechanisms of nanoparticle formation in the laser-induced plasma is finally discussed.

  1. Spin-offs from laser ablation in art conservation

    NASA Astrophysics Data System (ADS)

    Asmus, J.; Elford, J.; Parfenov, V.

    2013-05-01

    In 1973 The Center for Art Conservation Studies (CASS) was established at the University of California, San Diego (UCSD). This was in response to demonstrations that were conducted during January-March 1972 in Venice for UNESCO, Venice in Peril, International Fund for Monuments, and the Italian Petroleum Institute (ENI). The feasibility investigation explored in-situ pulsed holography, holographic interferometry, and laser ablation divestment for applications in art conservation practice. During subsequent decades scores of UCSD graduate and undergraduate students as well as conservators, conservation scientists, academics, and engineers who resided in CASS as "Visiting Scholars" contributed to advancing the understanding and performance of radiation technologies in the arts. Several technologies in addition to those involving optical wavelengths were also investigated to aid in art conservation and conservation science. Magnetic Resonance Imaging (MRI) and Nuclear Magnetic Resonance (NMR) were employed to detect and map moisture within masonry. Lead isotopic analyses revealed authenticity and provenance of Benin bronzes. Inside-out x-ray radiography facilitated the detection of defects in stone. Ultrasonic imaging was introduced for the mapping of fresco strata. Photoacoustic Spectroscopy (PAS) was used to characterize varnish layers on paintings. Digital image processing was introduced in order to detect and visualize pentimenti within paintings as well as to perform virtual restoration and provide interactive museum displays. Holographic images were employed as imaginary theater sets. In the years that followed the graduation of students and the visits of professional collaborators, numerous other applications of radiation ablation began appearing in a wide variety of other fields such as aircraft maintenance, ship maintenance, toxic chemical remediation, biological sterilization, food processing, industrial fabrication, industrial maintenance, nuclear

  2. Optical properties of tin oxide nanoparticles prepared by laser ablation in water: Influence of laser ablation time duration and laser fluence

    SciTech Connect

    Desarkar, Himadri Sankar; Kumbhakar, P. Mitra, A.K.

    2012-11-15

    Colloidal tin oxide nanoparticles are prepared by laser (having a wavelength of 1064 nm) ablation of tin metallic target immersed in pure deionized water. The influences of laser ablation time and laser fluence on the size and optical properties of the synthesized nanoparticles are studied. Prepared tin oxide nanoparticles are characterized by transmission electron microscope, selected area electron diffraction and UV-Visible absorption spectroscopy. The morphology of prepared tin oxide nanoparticles is found to be mostly spherical and with sizes in the nanometric range (mean radius of 3.2 to 7.3 nm). The measured UV-Visible absorption spectra show the presence of absorption peaks in the ultraviolet region. The band gap energy of samples prepared with different laser ablation time duration is calculated and is found to be increased with decrease in size (radius) of the prepared nanoparticles. Photoluminescence emission measurements at room temperature show that all the samples exhibit photoluminescence in the visible region. The peak photoluminescence emission intensity in the sample prepared with 50 min of laser ablation time is 3.5 times larger than that obtained in the sample prepared with 10 min of laser ablation time. - Highlights: Black-Right-Pointing-Pointer SnO{sub 2} nanoparticles (6.4-14.6 nm) are prepared by laser ablation in liquid technique. Black-Right-Pointing-Pointer The influences of laser ablation time and laser fluence are studied. Black-Right-Pointing-Pointer Samples are characterized by TEM and UV-Visible absorption spectroscopy. Black-Right-Pointing-Pointer UV-Visible absorption spectra exhibit quantum confinement effect. Black-Right-Pointing-Pointer Samples exhibit enhanced photoluminescence emissions in the visible region.

  3. Femtosecond laser for cavity preparation in enamel and dentin: ablation efficiency related factors

    PubMed Central

    Chen, H.; Li, H.; Sun, YC.; Wang, Y.; Lü, PJ.

    2016-01-01

    To study the effects of laser fluence (laser energy density), scanning line spacing and ablation depth on the efficiency of a femtosecond laser for three-dimensional ablation of enamel and dentin. A diode-pumped, thin-disk femtosecond laser (wavelength 1025 nm, pulse width 400 fs) was used for the ablation of enamel and dentin. The laser spot was guided in a series of overlapping parallel lines on enamel and dentin surfaces to form a three-dimensional cavity. The depth and volume of the ablated cavity was then measured under a 3D measurement microscope to determine the ablation efficiency. Different values of fluence, scanning line spacing and ablation depth were used to assess the effects of each variable on ablation efficiency. Ablation efficiencies for enamel and dentin were maximized at different laser fluences and number of scanning lines and decreased with increases in laser fluence or with increases in scanning line spacing beyond spot diameter or with increases in ablation depth. Laser fluence, scanning line spacing and ablation depth all significantly affected femtosecond laser ablation efficiency. Use of a reasonable control for each of these parameters will improve future clinical application. PMID:26864679

  4. Femtosecond laser for cavity preparation in enamel and dentin: ablation efficiency related factors

    NASA Astrophysics Data System (ADS)

    Chen, H.; Li, H.; Sun, Yc.; Wang, Y.; Lü, Pj.

    2016-02-01

    To study the effects of laser fluence (laser energy density), scanning line spacing and ablation depth on the efficiency of a femtosecond laser for three-dimensional ablation of enamel and dentin. A diode-pumped, thin-disk femtosecond laser (wavelength 1025 nm, pulse width 400 fs) was used for the ablation of enamel and dentin. The laser spot was guided in a series of overlapping parallel lines on enamel and dentin surfaces to form a three-dimensional cavity. The depth and volume of the ablated cavity was then measured under a 3D measurement microscope to determine the ablation efficiency. Different values of fluence, scanning line spacing and ablation depth were used to assess the effects of each variable on ablation efficiency. Ablation efficiencies for enamel and dentin were maximized at different laser fluences and number of scanning lines and decreased with increases in laser fluence or with increases in scanning line spacing beyond spot diameter or with increases in ablation depth. Laser fluence, scanning line spacing and ablation depth all significantly affected femtosecond laser ablation efficiency. Use of a reasonable control for each of these parameters will improve future clinical application.

  5. Influence of an Angular Hatching Exposure Strategy on the Surface Roughness During Picosecond Laser Ablation of Hard Materials

    NASA Astrophysics Data System (ADS)

    Daniel, Christian; Manderla, Jannik; Hallmann, Sina; Emmelmann, Claus

    Innovative chip breakers for cutting tools made of very hard materials require laser ablation and demand a high quality regarding the manufactured surface. When processing materials such as polycrystalline cubic boron-nitride or tungsten carbide the surface roughness by laser ablation reaches Sa = 1,0-2,9 μm compared to Sa = 0,42 μm achieved by grinding. Therefore in the presented research the influence of the hatching exposure strategy on surface roughness during picosecond laser ablation of tungsten carbide is examined. The areal, layerwise ablation process is separated into its elements which are represented by intersection zones between single and multiple laser vectors. Thus two mechanisms of roughness formation are identified and described by model functions. Further the mechanisms are transferred to areal ablation in which surface roughness decreases due to improved hatching angles compared to a commonly used one of φ= 0°/90°. With this approach the roughness is reduced by approximately factor 2,0-3,5 to Sa = 0,82 μm. In conclusion guidelines are derived which present favorable settings for high quality laser ablation processes.

  6. Excimer laser surface ablation: a review of recent literature.

    PubMed

    O'Brart, David P S

    2014-01-01

    The aim was to review the recently published literature on excimer laser surface ablation procedures, including photorefractive keratectomy (PRK), laser sub-epithelial keratomileusis (LASEK), microkeratome-assisted PRK (epi-LASIK) and trans-epithelial (laser-assisted) PRK, to help elucidate where and how surface ablation may best fit into current refractive surgical practice. The emphasis was on publications within the last three years and included systemic reviews, meta-analyses and randomised controlled trials. Where such evidence did not exist, selective large series cohort studies, case-controlled studies and case series with follow-up preferably greater than six months were examined and included. Refractive and visual outcomes are excellent and comparable to those after LASIK even in complex cases after previous corneal surgery. Indeed, surface ablation combined with corneal collagen cross-linking may be used in selected eyes with biomechanical instability, where LASIK is contraindicated. In addition, there is evidence to suggest that there may be less induction of higher order aberrations with surface techniques. Long-term stability and safety appear to be extremely satisfactory. The literature supports the use of modern excimer laser surface treatments, with outcomes comparable to those after LASIK and evidence of less induction of higher-order aberrations. Follow-up studies at 10 to 20 years indicate excellent stability and safety.

  7. Laser ablation efficiency during the production of Ag nanoparticles in ethanol at a low pulse repetition rate (1-10 Hz)

    NASA Astrophysics Data System (ADS)

    Valverde-Alva, M. A.; García-Fernández, T.; Esparza-Alegría, E.; Villagrán-Muniz, M.; Sánchez-Aké, C.; Castañeda-Guzmán, R.; de la Mora, M. B.; Márquez-Herrera, C. E.; Sánchez Llamazares, J. L.

    2016-10-01

    We studied the effect of the repetition rate of laser pulses (RRLP) in the range from 1-10 Hz in the production of silver nanoparticles (Ag-NPs) by laser ablation in ethanol. Laser pulses with a duration of 7 ns, a wavelength of 1064 nm and an energy of 60 mJ were used to ablate a 99.99% pure silver target immersed in 10 ml of ethanol. Transmittance analysis and atomic absorption spectroscopy were used to study the silver concentration in the colloidal solutions. The ablation process was studied by measuring the transmission of the laser pulses through the colloid. It is shown that for a fixed number of laser pulses (NLP) the ablation efficiency, in terms of the ablated silver mass per laser pulse, increases with the RRLP. This result contradicts what had previously been established in the literature.

  8. Laser ablation of advanced ceramics and glass-ceramic materials: Reference position dependence

    NASA Astrophysics Data System (ADS)

    Sola, D.; Escartín, A.; Cases, R.; Peña, J. I.

    2011-04-01

    In this work, we present the effect produced by modifying the reference position as well as the method of machining on the results obtained when advanced ceramics and glass-ceramic materials are machined by laser ablation. A Q-switched Nd:YAG laser at its fundamental wavelength of 1064 nm with pulsewidths in the nanosecond range has been used. Morphology, depth and volume obtained by means of pulse bursts and grooves have been studied. Working within the same laser conditions, it has been shown that these values depend on the thermal, optical and mechanical features of the material processed. We have also studied the variation in the ablation yield when the position of the surface to be machined is modified. Material properties and work conditions are related to the results obtained. We have described and discussed the morphology, composition, microstructure and hardness of the materials processed.

  9. Spatial and Temporal Investigations of Laser Ablation Plasma Plume Density and Composition

    NASA Astrophysics Data System (ADS)

    Iratcabal, Jeremy; Bach, Bernhard; Beatty, Cuyler; Dutra, Eric; Darling, Timothy; Wiewior, Piotr; Covington, Aaron

    2016-10-01

    Laser ablation of solid targets with laser intensities of the order of 108-1011 W/cm2 provides a rich platform for investigating the density and composition of coexisting molecular, atomic, and ion species in the resulting plasma plume. Experiments measuring the spatial- and temporal-evolution of laser ablation plumes have been performed to simultaneously characterize the multiple parameters related to the energy and momentum partitioning of the incident laser energy as the ablation process occurs. The temperature, density, and relative populations of different molecular, atomic, and ion species can be determined by the simultaneous measurement of optical and charged particle spectroscopy, fast imaging cameras, and optical interferometric diagnostics. Additionally, background gas pressure, density, and species were carefully varied. A comparison of density measurements obtained with multiple interferometric, spectroscopic, and fast imaging diagnostics for a carbon ablation plume expanding into vacuum and into background gases with different Reynolds numbers will be presented. Atomic, molecular, and ion species population evolution will be presented as measured with optical and charged particle spectroscopy. This work was supported by the U.S. DOE NNSA Cooperative Agreement No. DE-NA0002075 and National Securities Technologies, LLC under Contract No. DE-AC52-06NA25946/subcontract No. 165819.

  10. Temperature profiles of 980- and 1,470-nm endovenous laser ablation, endovenous radiofrequency ablation and endovenous steam ablation.

    PubMed

    Malskat, W S J; Stokbroekx, M A L; van der Geld, C W M; Nijsten, T E C; van den Bos, R R

    2014-03-01

    Endovenous thermal ablation (EVTA) techniques are very effective for the treatment of varicose veins, but their exact working mechanism is still not well documented. The lack of knowledge of mechanistic properties has led to a variety of EVTA protocols and a commercially driven dissemination of new or modified techniques without robust scientific evidence. The aim of this study is to compare temperature profiles of 980-and 1,470-nm endovenous laser ablation (EVLA), segmental radiofrequency ablation (RFA), and endovenous steam ablation (EVSA). In an experimental setting, temperature measurements were performed using thermocouples; raw potato was used to mimic a vein wall. Two laser wavelengths (980 and 1,470 nm) were used with tulip-tip fibers and 1,470 nm also with a radial-emitting fiber. Different powers and pullback speeds were used to achieve fluences of 30, 60, and 90 J/cm. For segmental RFA, 1 cycle of 20 s was analyzed. EVSA was performed with two and three pulses of steam per centimeter. Maximum temperature increase, time span of relevant temperature increase, and area under the curve of the time of relevant temperature increase were measured. In all EVLA settings, temperatures increased and decreased rapidly. High fluence is associated with significantly higher temperatures and increased time span of temperature rise. Temperature profiles of 980- and 1,470-nm EVLA with tulip-tip fibers did not differ significantly. Radial EVLA showed significantly higher maximum temperatures than tulip-tip EVLA. EVSA resulted in mild peak temperatures for longer durations than EVLA. Maximum temperatures with three pulses per centimeter were significantly higher than with two pulses. RFA temperature rises were relatively mild, resulting in a plateau-shaped temperature profile, similar to EVSA. Temperature increase during EVLA is fast with a high-peak temperature for a short time, where EVSA and RFA have longer plateau phases and lower maximum temperatures.

  11. Laser ablation coupled with DAPNe-NSI-MS applied to redacted documents.

    PubMed

    Huynh, Vivian; Sasiene, Zachary J; Mach, Phillip M; Golden, Teresa D; Verbeck, Guido F

    2016-09-01

    Laser ablation has been applied to redacted documents, where the text has been concealed by other ink. This technique strips the redacting ink revealing the text that was once redacted. Once removed, a nanomanipulation technique is used to extract the ink of the underlying text where mass spectrometry is then implemented to analyze its ink chemistry. In order to facilitate microscopy with direct analyte-probed nanoextraction coupled to nanospray ionization mass spectrometry (DAPNe-NSI-MS), laser ablation must be executed prior to ink extraction. Laser ablation has a nondestructive approach of stripping the ink used to redact the document. Not only does this reveal the text, it clears an area for DAPNe to directly extract ink, in miniscule amounts, from the document without inducing destruction. The redacting ink was concluded to affect the aging process of the concealed handwritten ink more than the printed text. The redacted handwritten sample obtained higher relative peak area (%) values than the control samples (text that was not redacted) and the control for the printed text produced higher amounts of low molecular weight products than the sample. Implementing laser ablation on these samples could also affect the chemical properties of the underlying ink due to the additional UV radiation and plasma heating. Results indicate by using laser ablation to remove the redacting ink, the relative peak area of the underlying ink deviates by 1.25%. The thermal degradation of binding agents such as polymethylene, polyethylene glycol, and diethylene glycol was monitored by calculating the relative peak area for five days which, in turn, tracks the oxidation process. The relative peak area values were also used to determine the chemical kinetics of polyethylene glycol, where degradation and polymerization occur.

  12. Pre-ignition laser ablation of nanocomposite energetic materials

    SciTech Connect

    Stacy, S. C.; Massad, R. A.; Pantoya, M. L.

    2013-06-07

    Laser ignition of energetic material composites was studied for initiation with heating rates from 9.5 Multiplication-Sign 10{sup 4} to 1.7 Multiplication-Sign 10{sup 7} K/s. This is a unique heating rate regime for laser ignition studies because most studies employ either continuous wave CO{sub 2} lasers to provide thermal ignition or pulsed Nd:YAG lasers to provide shock ignition. In this study, aluminum (Al) and molybdenum trioxide (MoO{sub 3}) nanoparticle powders were pressed into consolidated pellets and ignited using a Nd:YAG laser (1064 nm wavelength) with varied pulse energy. Results show reduced ignition delay times corresponding to laser powers at the ablation threshold for the sample. Heating rate and absorption coefficient were determined from an axisymmetric heat transfer model. The model estimates absorption coefficients from 0.1 to 0.15 for consolidated pellets of Al + MoO{sub 3} at 1064 nm wavelength. Ablation resulted from fracturing caused by a rapid increase in thermal stress and slowed ignition of the pellet.

  13. CdTe nanoparticles synthesized by laser ablation

    SciTech Connect

    Semaltianos, N. G.; Logothetidis, S.; Perrie, W.; Romani, S.; Potter, R. J.; Dearden, G.; Watkins, K. G.; Sharp, M.

    2009-07-20

    Nanoparticle generation by laser ablation of a solid target in a liquid environment is an easy, fast, and 'green' method for a large scale production of nanomaterials with tailored properties. In this letter we report the synthesis of CdTe nanoparticles by femtosecond laser [387 nm, 180 fs, 1 kHz, pulse energy=6 {mu}J (fluence=1.7 J/cm{sup 2})] ablation of the target material. Nanoparticles with diameters from {approx}2 up to {approx}25 nm were observed to be formed in the colloidal solution. Their size distribution follows the log-normal function with a statistical median diameter of {approx_equal}7.1 nm. Their crystal structure is the same as that of the bulk material (cubic zincblende) and they are slightly Cd-rich (Cd:Te percentage ratio {approx}1:0.9). Photoluminescence emission from the produced nanoparticles was detected in the deep red ({approx}652 nm)

  14. Ablation and nanostructuring of metals by femtosecond laser pulses

    SciTech Connect

    Ashitkov, S I; Komarov, P S; Ovchinnikov, A V; Struleva, E V; Agranat, M B; Zhakhovskii, V V; Inogamov, N A

    2014-06-30

    Using an interferometric continuous monitoring technique, we have investigated the motion of the surface of an aluminium target in the case of femtosecond laser ablation at picosecond time delays relative to the instant of laser exposure. Measurements of the temporal target dispersion dynamics, molecular dynamics simulation results and the morphology of the ablation crater have demonstrated a thermomechanical (spall) nature of the disruption of the condensed phase due to the cavitation-driven formation and growth of vapour phase nuclei upon melt expansion, followed by the formation of surface nanostructures upon melt solidification. The tensile strength of heated aluminium in a condensed state has been determined experimentally at an expansion rate of ∼10{sup 9} s{sup -1}. (extreme light fields and their applications)

  15. Laser-ablation-assisted microparticle acceleration for drug delivery

    NASA Astrophysics Data System (ADS)

    Menezes, V.; Takayama, K.; Ohki, T.; Gopalan, J.

    2005-10-01

    Localized drug delivery with minimal tissue damage is desired in some of the clinical procedures such as gene therapy, treatment of cancer cells, treatment of thrombosis, etc. We present an effective method for delivering drug-coated microparticles using laser ablation on a thin metal foil containing particles. A thin metal foil, with a deposition of a layer of microparticles is subjected to laser ablation on its backface such that a shock wave propagates through the foil. Due to shock wave loading, the surface of the foil containing microparticles is accelerated to very high speeds, ejecting the deposited particles at hypersonic speeds. The ejected particles have sufficient momentum to penetrate soft body tissues, and the penetration depth observed is sufficient for most of the pharmacological treatments. We have tried delivering 1μm tungsten particles into gelatin models that represent soft tissues, and liver tissues of an experimental rat. Sufficient penetration depths have been observed in these experiments with minimum target damage.

  16. Laser Ablation Molecular Isotopic Spectrometry: Strontium and its isotopes

    NASA Astrophysics Data System (ADS)

    Mao, Xianglei; Bol'shakov, Alexander A.; Choi, Inhee; McKay, Christopher P.; Perry, Dale L.; Sorkhabi, Osman; Russo, Richard E.

    2011-11-01

    The experimental details are reported of Laser Ablation Molecular Isotopic Spectrometry (LAMIS) and its application for performing optical isotopic analysis of solid strontium-containing samples in ambient atmospheric air at normal pressure. The LAMIS detection method is described for strontium isotopes from samples of various chemical and isotopic compositions. The results demonstrate spectrally resolved measurements of the three individual 86Sr, 87Sr, and 88Sr isotopes that are quantified using multivariate calibration of spectra. The observed isotopic shifts are consistent with those calculated theoretically. The measured spectra of diatomic oxide and halides of strontium generated in laser ablation plasmas demonstrate the isotopic resolution and capability of LAMIS. In particular, emission spectra of SrO and SrF molecular radicals provided clean and well resolved spectral signatures for the naturally occurring strontium isotopes. A possibility is discussed of using LAMIS of strontium isotopes for radiogenic age determination.

  17. Comparison of kinetic theory models of laser ablation of carbon

    SciTech Connect

    Shusser, Michael

    2010-05-15

    The paper compares the predictions of three-dimensional kinetic theory models of laser ablation of carbon. All the models are based on the moment solution of the Boltzmann equation for arbitrary strong evaporation but use different approximations. Comparison of the model predictions demonstrated that the choice of the particular model has very little influence on the results. The influence of the heat conduction from the gas to the solid phase was also found to be negligible in this problem.

  18. Optical feedback signal for ultrashort laser pulse ablation of tissue

    SciTech Connect

    Kim, B.-M.; Feit, M.D.; Rubenchik, A.M.; Mammini, B.M.; Da Silva, L.B.

    1997-07-01

    An optical feedback system for controlled precise tissue ablation is discussed. Our setup includes an ultrashort pulse laser (USPL), and a diagnostic system using analysis of either tissue fluorescence or plasma emission luminescence. Current research is focused on discriminating hard and soft tissues such as bone and spinal cord during surgery using either technique. Our experimental observations exhibit considerable spectroscopic contrast between hard and soft tissue, and both techniques offer promise for a practical diagnostic system.

  19. Particle size dependent chemistry from laser ablation of brass.

    PubMed

    Liu, Chunyi; Mao, Xianglei; Mao, Sam S; Greif, Ralph; Russo, Richard E

    2005-10-15

    The proportion of zinc and copper in particles formed by laser ablation of brass was found to vary with the particle diameter. Energy-dispersive X-ray analysis showed that smaller particles were zinc enhanced while larger particles were composed mostly of copper. A model based on condensation of vapor onto large droplets ejected from a melted liquid layer is proposed to describe the change in particle composition versus size.

  20. Gallium nitride powerbar transistors with via holes fabricated by laser ablation

    NASA Astrophysics Data System (ADS)

    Lossy, Richard; Liero, Armin; Krüger, Olaf; Würfl, Joachim; Tränkle, Günther

    2006-03-01

    Low ohmic through-hole vias are fabricated for AlGaN/GaN HEMT powerbar devices on SiC substrates using laser ablation technique. A complete processing technique has been developed. Through-wafer micro holes with an aspect ratio of 4 were drilled using pulsed UV laser machining. A plating technique on steep side wall could be established. Feasibility and performance of laser drilled via holes were tested with large power devices and proved successful up to the packaging level. The device demonstrated 14 dB of linear gain and a saturated output power of 40 W.

  1. Interferometric diagnostic suite for ultrafast laser ablation of metals

    SciTech Connect

    Clarke, S. A.; Rodriguez, G.; Taylor, Antoinette J.,; Forsman, A. C.

    2004-01-01

    We report on the development of a suite of novel techniques to measure important characteristics in intense ultrashort laser solid target experiments such as critical surface displacement, ablation depth, and plasma characteristics. Measurement of these important characteristics on an ultrafast ({approx}50 fs) time scale is important in understanding the primary event mechanisms in laser ablation of metal targets. Unlike traditional methods that infer these characteristics from spectral power shifts, phase shifts in frequency domain interferometry (FDI) or laser breakthrough studies of multiple shots on bulk materials, these techniques directly measure these characteristics from a single ultrafast heating pulse. These techniques are based on absolute displacement interferometry and nanotopographic applications of wavefront sensors. By applying all these femtosecond time-resolved techniques to a range of materials (Al, Au, and Au on plastic) over a range of pulse energies (10{sup 11} to 10{sup 16} W/cm{sup 2}) and pulse durations (50 to 700 fs), greater insight into the ablation mechanism and its pulse parameter dependencies can be determined. Comparison of these results with hydrocode software programs also reveals the applicability of hydrocode models.

  2. Damage in materials following ablation by ultrashort laser pulses: A molecular-dynamics study

    SciTech Connect

    Bouilly, Delphine; Perez, Danny; Lewis, Laurent J.

    2007-11-01

    The formation of craters following femtosecond- and picosecond-pulse laser ablation in the thermal regime is studied using a generic two-dimensional numerical model based on molecular-dynamics simulations and the Lennard-Jones potential. Femtosecond pulses are found to produce very clean craters through a combination of etching of the walls and the formation of a very thin heat affected zone. Our simulations also indicate that dislocations are emitted continuously during all of the ablation process (i.e., for hundreds of ps). For picosecond pulses, we observe much thicker heat affected zones which result from melting and recrystallization following the absorption of the light. In this case also, continuous emission of dislocations--though fewer in number--takes place throughout the ablation process.

  3. In Situ Geochemical Analysis and Age Dating of Rocks Using Laser Ablation-Miniature Mass Spectrometer

    NASA Technical Reports Server (NTRS)

    Sinha, Mahadeva P.; Hecht, Michael H.; Hurowitz, Joel A.

    2012-01-01

    A miniaturized instrument for performing chemical and isotopic analysis of rocks has been developed. The rock sample is ablated by a laser and the neutral species produced are analyzed using the JPL-invented miniature mass spectrometer. The direct sampling of neutral ablated material and the simultaneous measurement of all the elemental and isotopic species are the novelties of this method. In this laser ablation-miniature mass spectrometer (LA-MMS) method, the ablated neutral atoms are led into the electron impact ionization source of the MMS, where they are ionized by a 70-eV electron beam. This results in a secondary ion pulse typically 10-100 microsecond wide, compared to the original 5-10-nanosecond laser pulse duration. Ions of different masses are then spatially dispersed along the focal plane of the magnetic sector of the miniature mass spectrometer and measured in parallel by a modified CCD (charge-coupled device) array detector capable of detecting ions directly. Compared to conventional scanning techniques, simultaneous measurement of the ion pulse along the focal plane effectively offers a 100% duty cycle over a wide mass range. LAMMS offers a more quantitative assessment of elemental composition than techniques that detect laser-ionized species produced directly in the ablation process because the latter can be strongly influenced by matrix effects that vary with the structure and geometry of the surface, the laser beam, and the ionization energies of the elements. The measurement of high-precision isotopic ratios and elemental composition of different rock minerals by LAMMS method has been demonstrated. The LA-MMS can be applied for the absolute age determination of rocks. There is no such instrument available presently in a miniaturized version that can be used for NASA space missions. Work is in progress in the laboratory for geochronology of rocks using LA-MMS that is based on K-Ar radiogenic dating technique.

  4. Third harmonic generation in air ambient and laser ablated carbon plasma

    SciTech Connect

    Singh, Ravi Pratap Gupta, Shyam L.; Thareja, Raj K.

    2015-12-15

    We report the third harmonic generation of a nanosecond laser pulse (1.06 μm) in air ambient and in the presence of nanoparticles from laser ablated carbon plasma. Significant decrease in the threshold of third harmonic generation and multi-fold increment in the intensity of generated third harmonic is observed in presence of carbon plasma. The third harmonic in air is due to the quasi-resonant four photon process involving vibrationally excited states of molecular ion of nitrogen due to electron impact ionization and laser pulse. Following optical emission spectroscopic observations we conclude that the presence of C{sub 2} and CN in the ablated plume play a vital role in the observed third harmonic signals.

  5. Shock wave mediated plume chemistry for molecular formation in laser ablation plasmas

    SciTech Connect

    Harilal, Sivanandan S.; Brumfield, Brian E.; Cannon, Bret D.; Phillips, Mark C.

    2016-02-16

    Laser ablation is used in a variety of applications albeit formation mechanisms of molecules and nanoclusters are not well understood. We investigated the formation mechanisms of AlO molecules during complex interactions between an Al laser plume expanding into ambient air at atmospheric pressure levels. To produce the plasma a high-purity Al target was ablated using 1064 nm, 6 ns laser pulses. Our results show that the plasma chemistry leading to the formation of AlO is mediated by shock waves. During the early times of plasma expansion, the generated shock waves at the plume edges act as a barrier for the combustion process and the molecular formation is prevalent after the shockwave collapse. The temporally and spatially resolved contour mapping of Al and AlO highlight the formation routes and persistence of species in the plasma and its relation to plume hydrodynamics.

  6. Polarization-selective alignment of a carbon nanotube film by using femtosecond laser ablation

    NASA Astrophysics Data System (ADS)

    Choi, S. B.; Byeon, C. C.; Park, D. J.; Jeong, M. S.

    2016-01-01

    We report on a considerable alignment of single-walled carbon nanotubes (SWCNTs) in randomly oriented bundles, by using a simple drop-and-dry method and irradiation with high-intensity femtosecond laser pulses. A remarkable third-harmonic generation was observed after irradiation with the laser pulses, whereas a narrow-band white-light continuum was generated in the as-prepared films. This observation, combined with scanning electron microscopy images, confirmed the high degree of alignment of the SWCNTs. In contrast to the pulsed irradiation of carbon soot, the powerdependent laser irradiation of a highly-purified SWCNT film show polarization-dependent ablation of individual nanotubes caused by polarization-dependent absorption. Raman spectroscopy results confirmed the presence of fractured nanotubes caused by the ablation processes. Polarizationresolved absorption spectroscopy results revealed that the aligned SWCNT film had potential usage in optical polarizers.

  7. Precise femtosecond laser ablation of dental hard tissue: preliminary investigation on adequate laser parameters

    NASA Astrophysics Data System (ADS)

    Hikov, Todor; Pecheva, Emilia; Montgomery, Paul; Antoni, Frederic; Leong-Hoi, Audrey; Petrov, Todor

    2017-01-01

    This work aims at evaluating the possibility of introducing state-of-the-art commercial femtosecond laser system in restorative dentistry by maintaining well-known benefits of lasers for caries removal, but also in overcoming disadvantages such as thermal damage of irradiated substrate. Femtosecond ablation of dental hard tissue is investigated by changing the irradiation parameters (pulsed laser energy, scanning speed and pulse repetition rate), assessed for enamel and dentin. The femtosecond laser system used in this work may be suitable for cavity preparation in dentin and enamel, due to the expected effective ablation and low temperature increase when using ultra short laser pulses. If adequate laser parameters are selected, this system seems to be promising for promoting a laser-assisted, minimally invasive approach in restorative dentistry.

  8. Comparison of soft and hard tissue ablation with sub-ps and ns pulse lasers

    SciTech Connect

    Da Silva, L.B.; Stuart, B.C.; Celliers, P.M.; Feit, M.D.; Glinsky, M.E.; Heredia, N.J.; Herman, S.; Lane, S.M.; London, R.A.; Matthews, D.L.; Perry, M.D.; Rubenchik, A.M.; Chang, T.D.; Neev, J.

    1996-05-01

    Tissue ablation with ultrashort laser pulses offers several unique advantages. The nonlinear energy deposition is insensitive to tissue type, allowing this tool to be used for soft and hard tissue ablation. The localized energy deposition lead to precise ablation depth and minimal collateral damage. This paper reports on efforts to study and demonstrate tissue ablation using an ultrashort pulse laser. Ablation efficiency and extent of collateral damage for 0.3 ps and 1000 ps duration laser pulses are compared. Temperature measurements of the rear surface of a tooth section is also presented.

  9. Production of Calcium Phosphate Nanoparticles by Laser Ablation in Liquid

    NASA Astrophysics Data System (ADS)

    Boutinguiza, M.; Pou, J.; Lusquiños, F.; Comesaña, R.; Riveiro, A.

    Calcium phosphate nanoparticles represent an important object of investigation in the field of biomaterials due to the new properties obtainable at nanoscale. In this work calcium phosphate nanoparticles are obtained by laser ablation of hydroxyapatite (HA) targets in water and in ambient conditions; on the other hand particles of HA are reduced to nanoscale by laser-induced fracture. The results show that nanometric particles of calcium phosphate can be obtained. The morphology and the composition of the obtained particles were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and conventional and high resolution transmission electron microscopy (TEM, HRTEM).

  10. Analysis of excimer laser radiant exposure effect toward corneal ablation volume at LASIK procedure

    NASA Astrophysics Data System (ADS)

    Adiati, Rima Fitria; Rini Rizki, Artha Bona; Kusumawardhani, Apriani; Setijono, Heru; Rahmadiansah, Andi

    2016-11-01

    LASIK (Laser Asissted In Situ Interlamelar Keratomilieusis) is a technique for correcting refractive disorders of the eye such as myopia and astigmatism using an excimer laser. This procedure use photoablation technique to decompose corneal tissues. Although preferred due to its efficiency, permanency, and accuracy, the inappropriate amount radiant exposure often cause side effects like under-over correction, irregular astigmatism and problems on surrounding tissues. In this study, the radiant exposure effect toward corneal ablation volume has been modelled through several processes. Data collecting results is laser data specifications with 193 nm wavelength, beam diameter of 0.065 - 0.65 cm, and fluence of 160 mJ/cm2. For the medical data, the myopia-astigmatism value, cornea size, corneal ablation thickness, and flap data are taken. The first modelling step is determining the laser diameter between 0.065 - 0.65 cm with 0.45 cm increment. The energy, power, and intensity of laser determined from laser beam area. Number of pulse and total energy is calculated before the radiant exposure of laser is obtained. Next is to determine the parameters influence the ablation volume. Regression method used to create the equation, and then the spot size is substituted to the model. The validation used is statistic correlation method to both experimental data and theory. By the model created, it is expected that any potential complications can be prevented during LASIK procedures. The recommendations can give the users clearer picture to determine the appropriate amount of radiant exposure with the corneal ablation volume necessary.

  11. Adjustment of ablation shapes and subwavelength ripples based on electron dynamics control by designing femtosecond laser pulse trains

    NASA Astrophysics Data System (ADS)

    Yuan, Yanping; Jiang, Lan; Li, Xin; Wang, Cong; Lu, Yongfeng

    2012-11-01

    A quantum model is proposed to investigate femtosecond laser pulse trains processing of dielectrics by including the plasma model with the consideration of laser particle-wave duality. Central wavelengths (400 nm and 800 nm) strongly impact the surface plasmon field distribution, the coupling field intensity distribution (between the absorbed intensity and the surface plasma), and the distribution of transient localized free electron density in the material. This, in turn, significantly changes the localized transient optical/thermal properties during laser materials processing. The effects of central wavelengths on ablation shapes and subwavelength ripples are discussed. The simulation results show that: (1) ablation shapes and the spacing of subwavelength ripples can be adjusted by localized transient electron dynamics control using femtosecond laser pulse trains; (2) the adjustment of the radii of ablation shapes is stronger than that of the periods of subwavelength ripples.

  12. Surface modification of a biodegradable composite by UV laser ablation: in vitro biological performance.

    PubMed

    Martins, Albino; Gang, Wu; Pinho, Elisabete D; Rebollar, Esther; Chiussi, Stefano; Reis, Rui L; León, Betty; Neves, Nuno M

    2010-08-01

    Melt blends of chitosan and biodegradable aliphatic polyester have been physically and biologically studied, presenting great potential for biomedical applications. Structurally, poly(butylene succinate)-chitosan (PBS/Cht) composite scaffolds are covered by a thin PBS layer, preventing the desired interaction of cells/tissues with the chitosan particules. In the present work, a selective and controlled ablation of this skin layer was induced by UV laser processing. X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) data demonstrated an increment of chitosan components and others resulting from the laser ablation process. The biological activity (i.e. cell viability and proliferation) on the inner regions of the composite scaffolds is not significantly different from those of the external layer, despite the observed differences in surface roughness (determined by interferometric optical profilometry) and wettability (water contact angle). However, the morphology of human osteoblastic cells was found to be considerably different in the case of laser-processed samples, since the cells tend to aggregate in multilayer columnar structures, preferring the PBS surface and avoiding the chitosan-rich areas. Thus, UV laser ablation can be considered a model technique for the physical surface modification of biomaterials without detrimental effects on cellular activity.

  13. Gold fingerprinting by laser ablation inductively coupled plasma mass spectrometry

    NASA Astrophysics Data System (ADS)

    Watling, R. John; Herbert, Hugh K.; Delev, Dianne; Abell, Ian D.

    1994-02-01

    Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) has been applied to the characterization of the trace element composition "fingerprint" of selected gold samples from Western Australia and South Africa. By comparison of the elemental associations it is possible to relate gold to a specific mineralizing event, mine or bullion sample. This methodology facilitates identification of the provenance of stolen gold or gold used in salting activities. In this latter case, it is common for gold from a number of sources to be used in the salting process. Consequently, gold in the prospect being salted will not come from a single source and identification of multiple sources for this gold will establish that salting has occurred. Preliminary results also indicate that specific elemental associations could be used to identify the country of origin of gold. The technique has already been applied in 17 cases involving gold theft in Western Australia, where it is estimated that up to 2% of gold production is "relocated" each year as a result of criminal activities.

  14. Properties of zirconia thin films deposited by laser ablation

    SciTech Connect

    Cancea, V. N.; Filipescu, M.; Colceag, D.; Dinescu, M.; Mustaciosu, C.

    2013-11-13

    Zirconia thin films have been deposited by laser ablation of a ceramic ZrO{sub 2} target in vacuum or in oxygen background at 0.01 mbar. The laser beam generated by an ArF laser (λ=193 nm, ν=40 Hz) has been focalized on the target through a spherical lens at an incident angle of 45°. The laser fluence has been established to a value from 2.0 to 3.4 Jcm{sup −2}. A silicon (100) substrate has been placed parallel to the target, at a distance of 4 cm, and subsequently has been heated to temperatures ranging between 300 °C and 600 °C. Thin films morphology has been characterized by atomic force microscopy and secondary ion mass spectrometry. Biocompatibility of these thin films has been assessed by studying the cell attachment of L929 mouse fibroblasts.

  15. Ablation of biological tissues by radiation of strontium vapor laser

    SciTech Connect

    Soldatov, A. N. Vasilieva, A. V.

    2015-11-17

    A two-stage laser system consisting of a master oscillator and a power amplifier based on sources of self- contained transitions in pairs SrI and SrII has been developed. The radiation spectrum contains 8 laser lines generating in the range of 1 – 6.45 μm, with a generation pulse length of 50 – 150 ns, and pulse energy of ∼ 2.5 mJ. The divergence of the output beam was close to the diffraction and did not exceed 0.5 mrad. The control range of the laser pulse repetition rate varied from 10 to 15 000 Hz. The given laser system has allowed to perform ablation of bone tissue samples without visible thermal damage.

  16. Towards nanopatterning by femtosecond laser ablation of pre-stretched elastomers

    NASA Astrophysics Data System (ADS)

    Surdo, Salvatore; Piazza, Simonluca; Ceseracciu, Luca; Diaspro, Alberto; Duocastella, Martí

    2016-06-01

    Diffraction limits the focusing capabilities of an optical system seriously constraining the use of lasers for nanopatterning. In this work, we present a novel and simple approach to reduce the minimum feature size of a laser-direct write system by ablating a pre-stretched material. In particular, by focusing and scanning a femtosecond laser beam on the surface of a uniaxially pre-stretched elastomeric membrane we are able to obtain microstructures according to a desired pattern. After removing the stress applied to the elastomer, the membrane relaxes to its original size and the ablated patterns shrink while preserving their shape. In this way, the minimum feature size that is typically determined by the optical properties of the focusing system can be now controlled by the strain applied to the elastomer during the ablation process. We demonstrate this approach by ablating lines on a stretchable polymeric membrane at different strain conditions. Experimental results are in good agreement with theoretical predictions. The proposed method opens up new interesting possibilities for the rapid prototyping of micro- and nano-structures suitable for a wide range of applications such as soft-lithography, micro-/nano-fluidics and lab-on-chip.

  17. Combined optical tweezers and laser dissector for controlled ablation of functional connections in neural networks

    NASA Astrophysics Data System (ADS)

    Difato, Francesco; Dal Maschio, Marco; Marconi, Emanuele; Ronzitti, Giuseppe; Maccione, Alessandro; Fellin, Tommasso; Berdondini, Luca; Chieregatti, Evelina; Benfenati, Fabio; Blau, Axel

    2011-05-01

    Regeneration of functional connectivity within a neural network after different degrees of lesion is of utmost clinical importance. To test pharmacological approaches aimed at recovering from a total or partial damage of neuronal connections within a circuit, it is necessary to develop a precise method for controlled ablation of neuronal processes. We combined a UV laser microdissector to ablate neural processes in vitro at single neuron and neural network level with infrared holographic optical tweezers to carry out force spectroscopy measurements. Simultaneous force spectroscopy, down to the sub-pico-Newton range, was performed during laser dissection to quantify the tension release in a partially ablated neurite. Therefore, we could control and measure the damage inflicted to an individual neuronal process. To characterize the effect of the inflicted injury on network level, changes in activity of neural subpopulations were monitored with subcellular resolution and overall network activity with high temporal resolution by concurrent calcium imaging and microelectrode array recording. Neuronal connections have been sequentially ablated and the correlated changes in network activity traced and mapped. With this unique combination of electrophysiological and optical tools, neural activity can be studied and quantified in response to controlled injury at the subcellular, cellular, and network level.

  18. Development and fundamental investigation of Laser Ablation Glow Discharge Time-Of-Flight Mass Spectrometry (LA-GD-TOFMS)

    NASA Astrophysics Data System (ADS)

    Tarik, Mohamed; Lotito, Giovanni; Whitby, James A.; Koch, Joachim; Fuhrer, Katrin; Gonin, Marc; Michler, Johann; Bolli, Jean-Luc; Günther, Detlef

    2009-03-01

    Glow Discharge (GD) spectroscopy is a well known and accepted technique for the bulk and surface composition analysis, while laser ablation (LA) provides analysis with high spatial-resolution analysis in LIBS (laser-induced breakdown spectroscopy) or when coupled to inductively coupled plasma spectrometry (ICP-OES or ICP-MS). This work concerns the construction of a Laser Ablation Glow Discharge Time-Of-Flight Mass Spectrometry (LA-GD-TOFMS) instrument to study the analytical capabilities resulting from the interaction of a laser-generated sample plume with a pulsed glow discharge. Two ablation configurations were studied in detail. In a first approach, the laser-generated plume was introduced directly into the GD, while the second approach generated the plume inside the GD. The ablated material was introduced at different times with respect to the discharge pulse in order to exploit the efficient ionization in the GD plasma. For both LA-GD configurations, direct ablation into the afterglow of the pulsed glow discharge leads to an ion signal enhancement of up to a factor of 7, as compared to the ablation process alone under the same experimental conditions. The LA-GD enhancement was found to occur exclusively in the GD afterglow, with a maximum ablation S/N occurring in a few hundred microseconds after the termination of the glow discharge. The duration of the enhanced signal is about two milliseconds. Both the laser pulse energy and the position of the ablation plume (with respect to the sampling orifice) were found to affect the amount of mass entering the afterglow region and consequently, the enhancement factor of ionization.

  19. Testing of concrete by laser ablation

    DOEpatents

    Flesher, D.J.; Becker, D.L.; Beem, W.L.; Berry, T.C.; Cannon, N.S.

    1997-01-07

    A method is disclosed for testing concrete in a structure in situ, by: directing a succession of pulses of laser radiation at a point on the structure so that each pulse effects removal of a quantity of concrete and transfers energy to the concrete; detecting a characteristic of energy which has been transferred to the concrete; determining, separately from the detecting step, the total quantity of concrete removed by the succession of pulses; and calculating a property of the concrete on the basis of the detected energy characteristic and the determined total quantity of concrete removed. 1 fig.

  20. Testing of concrete by laser ablation

    DOEpatents

    Flesher, Dann J.; Becker, David L.; Beem, William L.; Berry, Tommy C.; Cannon, N. Scott

    1997-01-01

    A method of testing concrete in a structure in situ, by: directing a succession of pulses of laser radiation at a point on the structure so that each pulse effects removal of a quantity of concrete and transfers energy to the concrete; detecting a characteristic of energy which has been transferred to the concrete; determining, separately from the detecting step, the total quantity of concrete removed by the succession of pulses; and calculating a property of the concrete on the basis of the detected energy characteristic and the determined total quantity of concrete removed.

  1. Laser ablative synthesis of carbon nanotubes

    DOEpatents

    Smith, Michael W.; Jordan, Kevin; Park, Cheol

    2010-03-02

    An improved method for the production of single walled carbon nanotubes that utilizes an RF-induction heated side-pumped synthesis chamber for the production of such. Such a method, while capable of producing large volumes of carbon nanotubes, concurrently permits the use of a simplified apparatus that allows for greatly reduced heat up and cool down times and flexible flowpaths that can be readily modified for production efficiency optimization. The method of the present invention utilizes a free electron laser operating at high average and peak fluence to illuminate a rotating and translating graphite/catalyst target to obtain high yields of SWNTs without the use of a vacuum chamber.

  2. Ablation of selected conducting layers by fiber laser

    NASA Astrophysics Data System (ADS)

    Pawlak, Ryszard; Tomczyk, Mariusz; Walczak, Maria

    2014-08-01

    Laser Direct Writing (LDW) are used in the manufacture of electronic circuits, pads, and paths in sub millimeter scale. They can also be used in the sensors systems. Ablative laser writing in a thin functional layer of material deposited on the dielectric substrate is one of the LDW methods. Nowadays functional conductive layers are composed from graphene paint or nanosilver paint, indium tin oxide (ITO), AgHTTM and layers containing carbon nanotubes. Creating conducting structures in transparent layers (ITO, AgHT and carbon nanotubes layers) may have special importance e.g. for flexi electronics. The paper presents research on the fabrication of systems of paths and appropriate pattern systems of paths and selected electronic circuits in AgHTTM and ITO layers deposited on glass and polymer substrates. An influence of parameters of ablative fiber laser treatment in nanosecond regime as well as an influence of scanning mode of laser beam on the pattern fidelity and on electrical parameters of a generated circuit was investigated.

  3. Resonant holographic measurements of laser ablation plume expansion in vacuum and argon gas backgrounds

    SciTech Connect

    Lindley, Roger Alan

    1993-01-01

    This thesis discusses the following on resonant holographic measurements of laser ablation plume expansion: Introduction to laser ablation; applications of laser ablation; The study of plume expansion; holographic interferometry; resonant holographic interferometry; accounting for finite laser bandwidth; The solution for doppler broadening and finite bandwidth; the main optical table; the lumonics laser spot shape; developing and reconstructing the holograms; plume expansion in RF/Plasma Environments; Determining λ°; resonant refraction effects; fringe shift interpretation; shot-to-shot consistency; laser ablation in vacuum and low pressure, inert, background gas; theoretically modeling plume expansion in vacuum and low pressure, inert, background gas; and laser ablation in higher pressure, inert, background gas.

  4. Laser ablation of contaminants from concrete and metal surfaces. Topical report, June--December 1994

    SciTech Connect

    Freiwald, J.; Freiwald, D.A.

    1994-12-01

    Tests have demonstrated that it is possible to clean coatings off surfaces using high-power, pulsed, high-repetition-rate lasers. Purpose of this contract is to demonstrate (1) that pulsed-repetition lasers can be used to remove paint from concrete and metal surfaces, including cleaning out the surface pores, (2) that the cleaning process will result in negligible release of contaminated ablated material to the environment, and (3) that the process generates negligible additional waste compared to competing technologies. This report covers technical progress during Phase 1 of the contract and makes recommendations for technology development in Phase 2.

  5. Growth of anatase and rutile phase TiO2 nanoparticles using pulsed laser ablation in liquid: Influence of surfactant addition and ablation time variation

    NASA Astrophysics Data System (ADS)

    Chaturvedi, Amita; Joshi, M. P.; Mondal, P.; Sinha, A. K.; Srivastava, A. K.

    2017-02-01

    Titanium dioxide (TiO2) nanoparticles were grown using nanosecond pulsed laser ablation of Ti target in DI water and in 0.001 M sodium dodecyl sulfate (SDS) surfactant aqueous solution. Growth was carried out with varying ablation times i. e. 30 min, 60 min and 90 min. The objective of our study was to investigate the influence of variations in liquid ambience conditions on the growth of the nanoparticles in a pulsed laser ablation in liquid (PLAL) process. Size, composition and optical properties of the grown TiO2 nanoparticles were investigated using transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), optical absorption, photoluminescence (PL) spectroscopy and X-ray diffraction (XRD) studies. The obtained nanoparticles of TiO2 were found almost spherical in shape and polycrystalline in nature in both the liquid mediums i.e. DI water and aqueous solution of surfactant. Nanoparticles number density was also found to increase with increasing ablation time in both the liquid mediums. However crystalline phase of the grown TiO2 nanoparticles differs with the change in liquid ambience conditions. Selected area electron diffraction (SAED), PL and XRD studies suggest that DI water ambience is favorable for the growth of anatase phase TiO2 nanoparticles for all ablation times. While Surfactant added water ambience is favorable for the growth of rutile phase TiO2 nanoparticles but for shorter ablation times of 30 min and 60 min only, for longer ablation time of 90 min anatase phase was also observed along with the rutile phase TiO2 nanoparticles. The formation of anatase phase in DI water and rutile and anatase phase in aqueous solution of surfactant is explained on the basis of varying thermodynamic conditions with the two different liquid ambiences and different ablation times.

  6. Excimer laser ablation lithography applied to the fabrication of reflective diffractive optics

    NASA Astrophysics Data System (ADS)

    Flury, M.; Benatmane, A.; Gérard, P.; Montgomery, P. C.; Fontaine, J.; Engel, T.; Schunck, J. P.; Fogarassy, E.

    2003-03-01

    We propose a low cost technique for the production of diffractive optical elements (DOE). These elements are devoted to high power lasers beam shaping in the mid-infrared wavelengths. This process called laser ablation lithography (LAL), may seem similar to laser beam writing (LBW) in the way the whole DOE's design is reproduced pixel by pixel on the substrate placed on a computer controlled XY translation stage. A first difference is that the photoresist is not exposed with UV light but is directly ablated with short excimer laser pulses. Furthermore, with LAL technique the size of the smallest pixel ( 5 μm×5 μm) is more than 10 times greater than those produced by LBW. We discuss in details the experimental set-up for LAL and demonstrate that it gives a resolution up to 10 times greater than photolithography with flexible masks. This makes LAL a promising solution for the production of DOE for use with Nd:YAG lasers. New applications of DOEs are finally introduced with high power lasers sources, such as laser marking or multi-point brazing.

  7. Laser-induced back-ablation of aluminum thin films using picosecond laser pulses

    SciTech Connect

    BULLOCK, A B

    1999-05-26

    Experiments were performed to understand laser-induced back-ablation of Al film targets with picosecond laser pulses. Al films deposited on the back surface of BK-7 substrates are ablated by picosecond laser pulses propagating into the Al film through the substrate. The ablated Al plume is transversely probed by a time-delayed, two-color sub-picoseond (500 fs) pulse, and this probe is then used to produce self-referencing interferograms and shadowgraphs of the Al plume in flight. Optical emission from the Al target due to LIBA is directed into a time-integrated grating spectrometer, and a time-integrating CCD camera records images of the Al plume emission. Ablated Al plumes are also redeposited on to receiving substrates. A post-experimental study of the Al target and recollected deposit characteristics was also done using optical microscopy, interferometry, and profilometry. In this high laser intensity regime, laser-induced substrate ionization and damage strongly limits transmitted laser fluence through the substrate above a threshold fluence. The threshold fluence for this ionization-based transmission limit in the substrate is dependent on the duration of the incident pulse. The substrate ionization can be used as a dynamic control of both transmitted spatial pulse profile and ablated Al plume shape. The efficiency of laser energy transfer between the laser pulse incident on the Al film and the ablated Al plume is estimated to be of order 5% and is a weak function of laser pulsewidth. The Al plume is highly directed. Low plume divergence ({theta}{sub divergence} < 5{sup o}) shows the ablated plume temperature to be very low at long time delays ( T << 0.5 eV at delays of 255 ns). Spectroscopic observations and calculations indicate that, in early time (t < 100 ps), the Al film region near the substrate/metal interface is at temperatures of order 0.5 eV. Interferograms of Al plumes produced with 0.1 {micro}m films show these plumes to be of high neutral atom

  8. Time-resolved diagnostics of excimer laser-generated ablation plasmas used for pulsed laser deposition

    SciTech Connect

    Geohegan, D.B.

    1994-09-01

    Characteristics of laser plasmas used for pulsed laser deposition (PLD) of thin films are examined with four in situ diagnostic techniques: Optical emission spectroscopy, optical absorption spectroscopy, ion probe studies, and gated ICCD (intensified charge-coupled-device array) fast photography. These four techniques are complementary and permit simultaneous views of the transport of ions, excited states, ground state neutrals and ions, and hot particulates following KrF laser ablation of YBCO, BN, graphite and Si in vacuum and background gases. The implementation and advantages of the four techniques are first described in order to introduce the key features of laser plasmas for pulsed laser deposition. Aspects of the interaction of the ablation plume with background gases (i.e., thermalization, attenuation, shock formation) and the collision of the plasma plume with the substrate heater are then summarized. The techniques of fast ICCD photography and gated photon counting are then applied to investigate the temperature, velocity, and spatial distribution of hot particles generated during KrF ablation of YBCO, BN, Si and graphite. Finally, key features of fast imaging of the laser ablation of graphite into high pressure rare gases are presented in order to elucidate internal reflected shocks within the plume, redeposition of material on a surface, and formation of hot nanoparticles within the plume.

  9. Microfabrication of Fresnel zone plates by laser induced solid ablation

    NASA Astrophysics Data System (ADS)

    Rodrigues, Vanessa R. M.; Thomas, John; Santhosh, Chidangil; Ramachandran, Hema; Mathur, Deepak

    2016-07-01

    A novel and simple single-step method of inscribing optical elements on metal-coated transparent substrates is demonstrated. Laser induced solid ablation (LISA) demands very low laser energies (nJ), as can be amply provided by a femtosecond laser oscillator. Here, LISA is used to write Fresnel zone plates on indium and tungsten coated glass. With up to 100 zones, remarkable agreement is obtained between measured and expected values of the focal length. LISA has enabled attainment of focal spot sizes that are 38% smaller than what would be obtained using conventional lenses of the same numerical aperture. The simplicity with which a high degree of automation can readily be achieved using LISA makes this cost-effective method amenable to a wide variety of applications related to microfabrication of optical elements.

  10. Laser Surface Preparation of Epoxy Composites for Secondary Bonding: Optimization of Ablation Depth

    NASA Technical Reports Server (NTRS)

    Palmieri, Frank L.; Hopkins, John; Wohl, Christopher J.; Lin, Yi; Connell, John W.; Belcher, Marcus A.; Blohowiak, Kay Y.

    2015-01-01

    Surface preparation has been identified as one of the most critical aspects of attaining predictable and reliable adhesive bonds. Energetic processes such as laser ablation or plasma treatment are amenable to automation and are easily monitored and adjusted for controlled surface preparation. A laser ablation process was developed to accurately remove a targeted depth of resin, approximately 0.1 to 20 micrometers, from a carbon fiber reinforced epoxy composite surface while simultaneously changing surface chemistry and creating micro-roughness. This work demonstrates the application of this process to prepare composite surfaces for bonding without exposing or damaging fibers on the surface. Composite panels were prepared in an autoclave and had a resin layer approximately 10 micrometers thick above the fiber reinforcement. These composite panels were laser surface treated using several conditions, fabricated into bonded panels and hygrothermally aged. Bond performance of aged, experimental specimens was compared with grit blast surface treated specimens using a modified double cantilever beam test that enabled accelerated saturation of the specimen with water. Comparison of bonded specimens will be used to determine how ablation depth may affect average fracture energies and failure modes.

  11. Surface chemical reaction of laser ablated aluminum sample for detonation initiation

    SciTech Connect

    Kim, Chang-hwan; Yoh, Jack J.

    2011-05-01

    We explore the evolution of metal plasma generated by high laser irradiances and its effect on the surrounding air by using shadowgraph images after laser pulse termination; hence the formation of laser supported detonation and combustion processes has been investigated. The essence of the paper is in observing initiation of chemical reaction between ablated aluminum plasma and oxygen from air by inducing high power laser pulse (>1000 mJ/pulse) and conduct a quantitative comparison of chemically reactive laser initiated waves with the classical detonation of exploding aluminum (dust) cloud in air. Findings in this work may lead to a new method of initiating detonation from metal sample in its bulk form without the need of mixing nano-particles with oxygen for initiation.

  12. Deciphering formation processes of banded iron formations from the Transvaal and the Hamersley successions by combined Si and Fe isotope analysis using UV femtosecond laser ablation

    NASA Astrophysics Data System (ADS)

    Steinhoefel, Grit; von Blanckenburg, Friedhelm; Horn, Ingo; Konhauser, Kurt O.; Beukes, Nicolas J.; Gutzmer, Jens

    2010-05-01

    To investigate the genesis of BIFs, we have determined the Fe and Si isotope composition of coexisting mineral phases in samples from the ˜2.5 billion year old Kuruman Iron Formation (Transvaal Supergroup, South Africa) and Dales Gorges Member of the Brockman Iron Formation (Hamersley Group, Australia) by UV femtosecond laser ablation coupled to a MC-ICP-MS. Chert yields a total range of δ 30Si between -1.3‰ and -0.8‰, but the Si isotope compositions are uniform in each core section examined. This uniformity suggests that Si precipitated from well-mixed seawater far removed from its sources such as hydrothermal vents or continental drainage. The Fe isotope composition of Fe-bearing mineral phases is much more heterogeneous compared to Si with δ 56Fe values of -2.2‰ to 0‰. This heterogeneity is likely due to variable degrees of partial Fe(II) oxidation in surface waters, precipitation of different mineral phases and post-depositional Fe redistribution. Magnetite exhibits negative δ 56Fe values, which can be attributed to a variety of diagenetic pathways: the light Fe isotope composition was inherited from the Fe(III) precursor, heavy Fe(II) was lost by abiotic reduction of the Fe(III) precursor or light Fe(II) was gained from external fluids. Micrometer-scale heterogeneities of δ 56Fe in Fe oxides are attributed to variable degrees of Fe(II) oxidation or to isotope exchange upon Fe(II) adsorption within the water column and to Fe redistribution during diagenesis. Diagenetic Fe(III) reduction caused by oxidation of organic matter and Fe redistribution is supported by the C isotope composition of a carbonate-rich sample containing primary siderite. These carbonates yield δ 13C values of ˜-10‰, which hints at a mixed carbon source in the seawater of both organic and inorganic carbon. The ancient seawater composition is estimated to have a minimum range in δ 56Fe of -0.8‰ to 0‰, assuming that hematite and siderite have preserved their primary Fe

  13. Evaluation of the analytical capability of NIR femtosecond laser ablation-inductively coupled plasma mass spectrometry.

    PubMed

    Hirata, Takafumi; Kon, Yoshiaki

    2008-03-01

    A laser ablation-inductively coupled plasma-mass spectrometric (LA-ICPMS) technique utilizing a titanium-sapphire (TiS) femtosecond laser (fs-laser) has been developed for elemental and isotopic analysis. The signal intensity profile, depth of the ablation pit and level of elemental fractionation were investigated in order to evaluate the analytical capability of the present fs-laser ablation-ICPMS technique. The signal intensity profile of (57)Fe, obtained from iron sulfide (FeS(2)), demonstrated that the resulting signal intensity of (57)Fe achieved by the fs-laser ablation was almost 4-times higher than that obtained by ArF excimer laser ablation under a similar energy fluence (5 J/cm(2)). In fs-laser ablation, there is no significant difference in a depth of the ablation pit between glass and zircon material, while in ArF laser ablation, the resulting crater depth on the zircon crystal was almost half the level than that obtained for glass material. Both the thermal-induced and particle size-related elemental fractionations, which have been thought to be main sources of analytical error in the LA-ICPMS analysis, were measured on a Harvard 91500 zircon crystal. The resulting fractionation indexes on the (206)Pb/(238)U (f(Pb/U)) and (238)U/(232)Th (f(U/Th)) ratios obtained by the present fs-laser ablation system were significantly smaller than those obtained by a conventional ArF excimer laser ablation system, demonstrative of smaller elemental fractionation. Using the present fs-laser ablation technique, the time profile of the signal intensity of (56)Fe and the isotopic ratios ((57)Fe/(54)Fe and (56)Fe/(54)Fe) have been measured on a natural pyrite (FeS(2)) sample. Repeatability in signal intensity of (56)Fe achieved by the fs-laser ablation system was significantly better than that obtained by ArF excimer laser ablation. Moreover, the resulting precision in (57)Fe/(54)Fe and (56)Fe/(54)Fe ratio measurements could be improved by the fs-laser ablation system

  14. Reduction of picosecond laser ablation threshold and damage via nanosecond pre-pulse for removal of dielectric layers on silicon solar cells

    NASA Astrophysics Data System (ADS)

    Brand, A. A.; Meyer, F.; Nekarda, J.-F.; Preu, R.

    2014-10-01

    Laser microstructuring of thin dielectric layers on sensitive electronic devices, such as crystalline silicon solar cells, requires a careful design of the laser ablation process. For instance, degradation of the substrate's crystallinity can vastly decrease minority carrier lifetime and consequently impair the efficiency of such devices. Short-pulse laser ablation seems well suited for clean and spatially confined structuring because of the small heat-affected zone in the remaining substrate material [Dube and Gonsiorawski in Conference record of the twenty first IEEE photovoltaic specialists conference, 624-628 1990]. The short-time regimes, however, generate steep temperature gradients that can lead to amorphization of the remaining silicon surface. By `heating' the substrate via a non-ablative laser pulse in the nanosecond regime before the actual ablation pulse occurs we are able to prevent amorphization of the surface of the silicon solar cell substrate, while lowering the ablation thresholds of a SiNx layer on crystalline silicon wafers.

  15. A unified model to determine the energy partitioning between target and plasma in nanosecond laser ablation of silicon

    SciTech Connect

    Galasso, G.; Kaltenbacher, M.; Tomaselli, A.; Scarpa, D.

    2015-03-28

    In semiconductor industry, pulsed nanosecond lasers are widely applied for the separation of silicon wafers. Here, the high intensities employed activate a cascade of complex multi-physical and multi-phase mechanisms, which finally result in the formation of a laser induced plasma, shielding the target from the incoming laser beam. Such induced plasma plume, by preventing the laser to effectively reach the target, reduces the overall efficiency and controllability of the ablation process. Modelling can be a useful tool in the optimization of industrial laser applications, allowing a deeper understanding of the way the laser energy distributes between target and induced plasma. Nevertheless, the highly multi-physical character of laser ablation poses serious challenges on the implementation of the various mechanisms underlying the process within a common modelling framework. A novel strategy is here proposed in order to simulate in a simplified, yet physically consistent way, a typical industrial application as laser ablation of silicon wafers. Reasonable agreement with experimental findings is obtained. Three fundamental mechanisms have been identified as the main factors influencing the accuracy of the numerical predictions: the transition from evaporative to volumetric mass removal occurring at critical temperature, the collisional and radiative processes underlying the initial plasma formation stage and the increased impact of the liquid ejection mechanism when a sub-millimeter laser footprint is used.

  16. Micromachining of microchannel on the polycarbonate substrate with CO 2 laser direct-writing ablation

    NASA Astrophysics Data System (ADS)

    Qi, Heng; Chen, Tao; Yao, Liying; Zuo, Tiechuan

    2009-05-01

    Low-power CO 2 laser direct-writing ablation was used to micromachine a microchannel on the polycarbonate substrate in this work. The influence of the process parameters (the laser power, the moving velocity of the laser beam and the scanning times) on the micromachining quality (the depth, the width and their aspect ratio) of the microchannel was experimentally studied. The depth and width of microchannel both increase with the increase of the laser power and the decrease of the moving velocity of the laser beam. When higher laser power and slower moving velocity were used, the polycarbonate surface bore more heat irradiated from the CO 2 laser for longer time which results in the formation of deeper and wider molten pool, hence the ability to fabricate bigger microchannel. Because of the effect of the laser power on the depth and width of microchannels, higher aspect (depth/width) ratio could be achieved using slower moving velocity and higher laser power, and it would reach a steady state when the laser power increases to 9.0 W possibly caused by the effect of laser power on the different directions of microchannel. The polycarbonate-polycarbonate chip was bonded with hot-press bonding technique.

  17. Pulsed laser ablation of complex oxides: The role of congruent ablation and preferential scattering for the film stoichiometry

    SciTech Connect

    Wicklein, S.; Koehl, A.; Dittmann, R.; Sambri, A.; Amoruso, S.; Wang, X.; Bruzzese, R.

    2012-09-24

    By combining structural and chemical thin film analysis with detailed plume diagnostics and modeling of the laser plume dynamics, we are able to elucidate the different physical mechanisms determining the stoichiometry of the complex oxides model material SrTiO{sub 3} during pulsed laser deposition. Deviations between thin film and target stoichiometry are basically a result of two effects, namely, incongruent ablation and preferential scattering of lighter ablated species during their motion towards the substrate in the O{sub 2} background gas. On the one hand, a progressive preferential ablation of the Ti species with increasing laser fluence leads to a regime of Ti-rich thin film growth at larger fluences. On the other hand, in the low laser fluence regime, a more effective scattering of the lighter Ti plume species results in Sr rich films.

  18. Terahertz refractive anisotropy on femtosecond laser pulse ablated semi-insulating gallium arsenide surface

    NASA Astrophysics Data System (ADS)

    Zhao, Zhenyu; Song, Zhiqiang; Bai, Feng; Shi, Wangzhou; Zhao, Quan-Zhong

    2017-04-01

    We present an artificial variation of THz refractive index ellipse from isotropy to anisotropy at the surface of <100>-oriented semi-insulating gallium arsenide (SI-GaAs) via femtosecond pulse laser ablation. The refractive index ellipse is determined by the frequency and the polarization of incident THz radiation. The THz wave is localized in the gap of columns of micro-ripples when the polarization of THz is parallel to the micro-ripples, while no electric energy localization occurs when the polarization of THz is perpendicular to the micro-ripples. We found that the laser ablation process can induce a periodic distribution of n-type GaAs at the surface of SI-GaAs. These n-type GaAs micro-ripples work as plasmonic resonators, which are proposed to be the origin of the induced refractive index anisotropy.

  19. Patterned graphene ablation and two-photon functionalization by picosecond laser pulses in ambient conditions

    SciTech Connect

    Bobrinetskiy, I. I. Otero, N.; Romero, P. M.; Emelianov, A. V.

    2015-07-27

    Direct laser writing is a technology with excellent prospects for mask-less processing of carbon-based nanomaterials, because of the wide range of photoinduced reactions that can be performed on large surfaces with submicron resolution. In this paper, we demonstrate the use of picoseconds laser pulses for one-step ablation and functionalization of graphene. Varying the parameters of power, pulse frequency, and speed, we demonstrated the ablation down to 2 μm width and up to mm-long lines as well as functionalization with spatial resolution less than 1 μm with linear speeds in the range of 1 m/s. Raman and atomic-force microscopy studies were used to indicate the difference in modified graphene states and correlation to the changes in optical properties.

  20. Experimental and modelling investigations into the laser ablation with picosecond pulses at second harmonics

    NASA Astrophysics Data System (ADS)

    Boerner, Paul; Zandonadi, Germana; Eberle, Gregory; Wegener, Konrad

    2015-03-01

    Ablation threshold experiments on various materials are carried out using a picosecond laser generating second harmonic radiation in air at atmospheric pressure. Various materials are investigated which vary according to their different electronic band gap structure and include: silicon, fine grain polycrystalline diamond, copper, steel and tungsten carbide. Through the use of scanning electron microscopy and 3D confocal microscopy, the crater depth and diameter are determined and a correlation is found. The ablation thresholds are given for the aforementioned materials and compared with recent literature results. Picosecond laser-material interactions are modelled using the two-temperature model, simulated and compared with experimental results for metallic materials. An extension of the two-temperature model to semiconducting and insulating materials is discussed. This alternative model uses multiple rate equations to describe the transient free electron density. Additionally, a set of coupled ordinary differential equations describes the processes of multiphoton excitation, inverse bremsstrahlung, and collisional excitation. The resulting electron density distribution can be used as an input for an electron density dependent twotemperature model. This multiple rate equation model is a generic and fast model, which provides important information like ablation threshold, ablation depth and optical properties.

  1. Responses of polymers to laser plasma EUV light beyond ablation threshold and micromachining

    NASA Astrophysics Data System (ADS)

    Makimura, Tetsuya; Torii, Shuichi; Okazaki, Kota; Nakamura, Daisuke; Takahashi, Akihiko; Niino, Hiroyuki; Okada, Tatsuo; Murakami, Kouichi

    2011-06-01

    We have investigated responses of PDMS, PMMA and acrylic block copolymers (BCP) to EUV light from laserproduced plasma beyond ablation thresholds and micromachining. We generated wide band EUV light around 100 eV by irradiation of Ta targets with Nd:YAG laser light. In addition, narrow band EUV light at 11 and 13 nm were generated by irradiation of solid Xe and Sn targets, respectively, with pulsed CO2 laser light. The generated EUV light was condensed onto samples, using an ellipsoidal mirror. The EUV light was incident through windows of contact masks on the samples. We found that through-holes with a diameter of 1 μm can be fabricated in PDMS sheets with thicknesses of 10 μm. PDMS sheets are ablated if they are irradiated with EUV light beyond a threshold power density, while PDMS surfaces were modified by irradiation with the narrow band EUV light at lower power densities. Effective ablation of PMMA sheets can be applied to a LIGA-like process for fabricating micro-structures of metals using the practical apparatus. Furthermore, BCP sheets were ablated to have micro-structures. Thus, we have developed a practical technique for microma chining of PMMA, PDMS and BCP sheets in a micrometer scale.

  2. Silver nanoparticles generated by pulsed laser ablation in supercritical CO2 medium

    NASA Astrophysics Data System (ADS)

    Machmudah, Siti; Sato, Takayuki; Wahyudiono; Sasaki, Mitsuru; Goto, Motonobu

    2012-03-01

    Pulsed laser ablation (PLA) has been widely employed in industrial and biological applications and in other fields. The environmental conditions in which PLA is conducted are important parameters that affect both the solid particle cloud and the deposition produced by the plume. In this work, the generation of nanoparticles (NPs) has been developed by performing PLA of silver (Ag) plates in a supercritical CO2 medium. Ag NPs were successfully generated by allowing the selective generation of clusters. Laser ablation was performed with an excitation wavelength of 532 nm under various pressures and temperatures of CO2 medium. On the basis of the experimental result, both surface of the irradiated Ag plate and structure of Ag NPs were significantly affected by the changes in supercritical CO2 pressure and temperature. With increasing irradiation pressure, plume deposited in the surrounding crater created by the ablation was clearly observed. In Field Emission Scanning Electron Microscopy (FE-SEM) the image of the generated Ag NPs on the silicon wafer and the morphology of Ag particles were basically a sphere-like structure. Ag particles contain NPs with large-varied diameter ranging from 5 nm to 1.2 μm. The bigger Ag NPs melted during the ablation process and then ejected smaller spherical Ag NPs, which formed nanoclusters attached on the molten Ag NPs. The smaller Ag NPs were also formed around the bigger Ag NPs. Based on the results, this new method can also be used to obtain advanced nano-structured materials.

  3. Effects of pulsed CO2 laser in caries selective ablation

    NASA Astrophysics Data System (ADS)

    Colojoara, Carmen; David, Ion; Marinovici, Mariana

    1995-03-01

    We have evaluated the effect of pulsed carbon dioxide laser in the treatment for deep carious decay. The so called `caries profonda' is still a problem for conservative dentistry. A `Valvfivre' Master 20S carbon dioxide laser was pulsed to determine the effects on dentine and for testing the properties of softened dentine in selective ablation. Laser treatment parameters were from 1 to 2 W, 50 to 150 ms, 200 to 320 Hz. Fifteen human teeth samples were exposed to irradiation: extracted third molar were exposed to CO2 pulsed laser to determine in vitro the effects on pulp morphology. The tissue samples were analyzed histologically and by means of scanning electron microscopy for evidence of thermal damage. Next, we have evaluated the morphologic changes in vivo on 10 cases in patients with deep carious decay. Pulsed infrared lasers are capable of inducing physical and chemical changes in dentine structure. The results showed an artificially sclerosing and micro-hardness on the remaining dentine. CO2 laser can vaporized carious dentine.

  4. Visual laser ablation of the prostate (VLAP) with the prostascope

    NASA Astrophysics Data System (ADS)

    Mattioli, Stefano; Cremona, M.; Ackaert, K. J.

    1997-12-01

    Introduction: Laser ablation of the prostatic tissue or laser prostatectomy, is used as an alternative method to traditional endoscopic resection of the prostate. The usual side-firing Nd:YAG laser fiber for the treatment of obstructive symptoms has operational difficulties, a high cost and often poor early results. Materials: We describe the laser coagulation of the prostate using a 600-um bare fiber inserted in a modified Albarran bridge which included at the tip, a new gold-plated deflectable reflector. The complete device passes through a 21Fr.rigid cysto- urethroscope. The system and the fiber can be used for several dozen treatments. The dosimetry was 2000 J per 1 cc of prostatic tissue. Methods: VLAP using the prostascope was performed on more than 70 men in one institution, and 150 in a second one, for obstructive symptoms due to benign prostatic hyperplasia. The parameter included AUA symptom score, flow rate, residual volume and complications. Data were obtained preoperatively and 1, 3, 6 and 12 months after treatment. Discussion: According to our data VLAP with this system is a save, minimal invasive and effective treatment. Results are comparable to other non-contact laser devices. As the gold-plated reflector is inexpensive and the standard bare fiber can be used repeatedly, the cost is less than of an usual side-firing laser fiber.

  5. Rapid cell-patterning and microfluidic chip fabrication by crack-free CO2 laser ablation on glass

    NASA Astrophysics Data System (ADS)

    Yen, Meng-Hua; Cheng, Ji-Yen; Wei, Cheng-Wey; Chuang, Yung-Chuan; Young, Tai-Horng

    2006-07-01

    This paper uses a widely available CO2 laser scriber (λ = 10.6 µm) to perform the direct-writing ablation of quartz, borofloat and pyrex substrates for the development of microfluidic chips and cell chips. The surface quality of the ablated microchannels and the presence of debris and distortion are examined by scanning electron microscopy, atomic force microscopy and surface profile measurement techniques. The developed laser ablation system provides a versatile and economic approach for the fabrication of glass microfluidic chips with crack-free structures. In the laser writing process, the desired microfluidic patterns are designed using commercial computer software and are then transferred to the laser scriber to ablate the trenches. This process eliminates the requirement for corrosive chemicals and photomasks, and hence the overall microchip development time is limited to less than 24 h. Additionally, since the laser writing process is not limited by the dimensions of a photomask, the microchannels can be written over a large substrate area. The machining capability and versatility of the laser writing system are demonstrated through its application to the fabrication of a borofloat microfluidic chip and the writing of a series of asymmetric trenches in a microwell array. It is shown that the minimum attainable trench width is 95 µm and that the maximum trench depth is 225 µm. The system provides an economic and powerful means of rapid glass microfluidic chip development. A rapid cell-patterning method based on this method is also demonstrated.

  6. Heat generation caused by ablation of dental hard tissues with an ultrashort pulse laser (USPL) system.

    PubMed

    Braun, Andreas; Krillke, Raphael Franz; Frentzen, Matthias; Bourauel, Christoph; Stark, Helmut; Schelle, Florian

    2015-02-01

    Heat generation during the removal of dental hard tissues may lead to a temperature increase and cause painful sensations or damage dental tissues. The aim of this study was to assess heat generation in dental hard tissues following laser ablation using an ultrashort pulse laser (USPL) system. A total of 85 specimens of dental hard tissues were used, comprising 45 specimens of human dentine evaluating a thickness of 1, 2, and 3 mm (15 samples each) and 40 specimens of human enamel with a thickness of 1 and 2 mm (20 samples each). Ablation was performed with an Nd:YVO4 laser at 1,064 nm, a pulse duration of 9 ps, and a repetition rate of 500 kHz with an average output power of 6 W. Specimens were irradiated for 0.8 s. Employing a scanner system, rectangular cavities of 1-mm edge length were generated. A temperature sensor was placed at the back of the specimens, recording the temperature during the ablation process. All measurements were made employing a heat-conductive paste without any additional cooling or spray. Heat generation during laser ablation depended on the dental hard tissue (enamel or dentine) and the thickness of the respective tissue (p < 0.05). Highest temperature increase could be observed in the 1-mm thickness group for enamel. Evaluating the 1-mm group for dentine, a significantly lower temperature increase could be measured (p < 0.05) with lowest values in the 3-mm group (p < 0.05). A time delay for temperature increase during the ablation process depending on the material thickness was observed for both hard tissues (p < 0.05). Employing the USPL system to remove dental hard tissues, heat generation has to be considered. Especially during laser ablation next to pulpal tissues, painful sensations and potential thermal injury of pulp tissue might occur.

  7. Growth modes of ZnO nanostructures from laser ablation

    SciTech Connect

    Amarilio-Burshtein, I.; Tamir, S.; Lifshitz, Y.

    2010-03-08

    ZnO nanowires (NWs) and other nanostructures were grown by laser ablation of a ZnO containing target onto different substrates with and without the presence of an Au catalyst. The morphology and structure of the NWs were studied using high resolution scanning and transmission electron microscopes [including imaging, selected area electron diffraction (SAED), and energy dispersive x-ray spectroscopy (EDS)]. The different growth modes obtainable could be tuned by varying the Zn concentration in the vapor phase keeping other growth parameters intact. Possible growth mechanisms of these nanowires are suggested and discussed.

  8. New technique using laser ablation blasts into geochemical labs

    NASA Astrophysics Data System (ADS)

    Sylvester, Paul J.

    Geochemists have long sought a low-cost, reliable instrument for analyzing trace elements in situ. After a quiet start in the mid-1980s, laser ablation inductively coupled plasma mass spectrometry (LA-ICPMS) has steadily captured the imagination of geochemists all over the world and is now becoming “standard equipment” in the modern geochemical laboratory. In recognition of this phenomenon, a special session on “Analytical methodologies and geochemical applications of LA-ICPMS” was held at the Fall AGU meeting in San Francisco.

  9. Thermal ablation of an aluminium film upon absorption of a femtosecond laser pulse

    SciTech Connect

    Bezhanov, S G; Kanavin, A P; Uryupin, S A

    2016-02-28

    We have found the time dependence of the ablation depth of aluminium irradiated by a femtosecond laser pulse. It is shown to what extent an increase in the radiation energy flux density leads to an increase in the quasi-stationary value of the ablation depth. By reducing the aluminium film thickness down to one hundred nanometres and less, the ablation depth significantly increases. At the same time, the quasi-stationary value of the ablation depth of a thin film is obtained due to the removal of heat from the focal spot region. (interaction of laser radiation with matter. laser plasma)

  10. Femtosecond Laser Ablated FBG with Composite Microstructure for Hydrogen Sensor Application

    PubMed Central

    Zou, Meng; Dai, Yutang; Zhou, Xian; Dong, Ke; Yang, Minghong

    2016-01-01

    A composite microstructure in fiber Bragg grating (FBG) with film deposition for hydrogen detection is presented. Through ablated to FBG cladding by a femtosecond laser, straight-trenches and spiral micro-pits are formed. A Pd–Ag film is sputtered on the surface of the laser processed FBG single mode fiber, and acts as hydrogen sensing transducer. The demonstrated experimental outcomes show that a composite structure produced the highest sensitivity of 26.3 pm/%H, nearly sevenfold more sensitive compared with original standard FBG. It offers great potential in engineering applications for its good structure stability and sensitivity. PMID:27916933

  11. Synthesis of silver nanoparticles by laser ablation in ethanol: A pulsed photoacoustic study

    NASA Astrophysics Data System (ADS)

    Valverde-Alva, M. A.; García-Fernández, T.; Villagrán-Muniz, M.; Sánchez-Aké, C.; Castañeda-Guzmán, R.; Esparza-Alegría, E.; Sánchez-Valdés, C. F.; Llamazares, J. L. Sánchez; Herrera, C. E. Márquez

    2015-11-01

    The pulsed photoacoustic (PA) technique was used to study the synthesis by laser ablation of silver nanoparticles (Ag-NPs) in ethanol. PA technique allowed to determine the production rate per laser pulse and concentration of synthesized Ag-NPs. The samples were produced by using a pulsed Nd:YAG laser with 1064 nm of wavelength and 7 ns of pulse duration. The laser pulse energy varied from 10 to 100 mJ. Transmission electron microscopy micrographs demonstrated that the obtained nanoparticles were spherical with an average size close to 10 nm. The absorption spectra of the colloids showed a plasmon absorption peak around 400 nm. The PA analyses showed a significant reduction of the production rate of Ag-NPs during the first hundreds of laser pulses. For a higher number of pulses this rate was kept almost constant. Finally, we found that the root mean square (RMS) value of the PA signal was proportional to the laser pulse fluence on the target surface. Thus PA technique was useful to monitor the ablation process.

  12. Laser ablated copper plasmas in liquid and gas ambient

    SciTech Connect

    Kumar, Bhupesh; Thareja, Raj K.

    2013-05-15

    The dynamics of copper ablated plasma plumes generated using laser ablation of copper targets in both liquid (de-ionized water) and gas (air) ambients is reported. Using time and space resolved visible emission spectroscopy (450-650 nm), the plasma plumes parameters are investigated. The electron density (n{sub e}) determined using Stark broadening of the Cu I (3d{sup 10}4d{sup 1} {sup 2}D{sub 3/2}-3d{sup 10}4p{sup 1} {sup 2}P{sub 3/2} at 521.8 nm) line is estimated and compared for both plasma plumes. The electron temperature (T{sub e}) was estimated using the relative line emission intensities of the neutral copper transitions. Field emission scanning electron microscopy and energy dispersive x-ray spectral analysis of the ablated copper surface indicated abundance of spherical nanoparticles in liquid while those in air are amalgamates of irregular shapes. The nanoparticles suspended in the confining liquid form aggregates and exhibit a surface plasmon resonance at ∼590 nm.

  13. Multidiagnostic analysis of ultrafast laser ablation of metals with pulse pair irradiation

    NASA Astrophysics Data System (ADS)

    Amoruso, S.; Bruzzese, R.; Wang, X.; O'Connell, G.; Lunney, J. G.

    2010-12-01

    Copper targets are irradiated in the ablation regime by pairs of equal, time-delayed collinear laser pulses separated on a timescale going from ≈2 ps to ≈2 ns. The ablation plume is characterized by ion probe diagnostic, fast imaging, and temporally and spatially resolved optical emission spectroscopy. The variation in the ablation efficiency with the delay between the pulses is analyzed by measuring the ablation crater profile with a contact profilometer. The second laser pulse modifies the characteristics of the plasma plume produced by the first pulse and the ablation efficiency. The different mechanisms involved in double pulse ultrafast laser ablation are identified and discussed. The experimental findings are interpreted in the frame of a simple model of the interaction of the second pulse with the nascent ablation plume produced by the first pulse. This model yields consistent and quantitative agreement with the experimental findings predicting the observed experimental trends of the ablation depth reduction and ion yield increase with the delay between the pulses, as well as the characteristic timescale of the observed changes. The possibility of controlling the characteristics of the plumes produced during ultrafast laser ablation via an efficient coupling of the energy of the second pulse to the various ablation components produced by the first pulse is of particular interest in ultrafast pulsed laser deposition and microprobe analyses of materials.

  14. Time Resolved Shadowgraph Images of Silicon during Laser Ablation:Shockwaves and Particle Generation

    SciTech Connect

    Liu, C.Y.; Mao, X.L.; Greif, R.; Russo, R.E.

    2006-05-06

    Time resolved shadowgraph images were recorded of shockwaves and particle ejection from silicon during laser ablation. Particle ejection and expansion were correlated to an internal shockwave resonating between the shockwave front and the target surface. The number of particles ablated increased with laser energy and was related to the crater volume.

  15. Approximate theory of highly absorbing polymer ablation by nanosecond laser pulses

    NASA Astrophysics Data System (ADS)

    Furzikov, N. P.

    1990-04-01

    Surface interference, nonlinearly saturated instability of laser-induced thermodestruction, and subsequent oscillation of absorption mode permit the description of analytical ablation thresholds and depths per pulse of polymers having high absorption at laser wavelengths, e.g., polyimide and poly(ethylene terephtalate). Inverse problem solution for polycarbonate and ablation invariant designing are also realized.

  16. Effect of nanosecond pulse laser ablation on the surface morphology of Zr-based metallic glass

    NASA Astrophysics Data System (ADS)

    Zhu, Yunhu; Fu, Jie; Zheng, Chao; Ji, Zhong

    2016-09-01

    In this study, we investigated the ripple patterns formation on the surface of Zr41.2Ti13.8Cu12.5Ni10Be22.5 (vit1) bulk metallic glass using a nanosecond pulse laser ablation in air with a wavelength of 1064 nm. The strong thermal ablation phenomenon could be observed on vit1 BMG surface at laser energy of 200 mJ as a result of the adhibition of confining overlay. Many periodic ripples had formed on the edge of the ablated area at laser energy of 400 mJ because of the high intensity pulsed laser beam. The underlying mechanism of the periodic ripples formation could be explained by the K-H hydrodynamic instability theory. It had been shown that laser ablation with 600 mJ and 200 pulses results in the formation of many micro-cracks on the ablated area. Further analysis showed that the spatial occupation of the laser ablated area and the spacing between two adjacent ripples increased as the laser energy and the number of incident laser pulses increasing. The surface ripples feature on the edge of ablated area became more obvious with increasing laser pulses, but it was not correlated closely with the laser energies variation.

  17. Comparison of the effectiveness of nonablative fractional laser versus ablative fractional laser in thyroidectomy scar prevention: A pilot study.

    PubMed

    Kim, Hei Sung; Lee, Ji Hae; Park, Young Min; Lee, Jun Young

    2012-04-01

    A scar is a mark that remains after the healing of a wound or other morbid processes. In the past, treatment was mainly focused on severe scarring, such as the hypertrophic and burn scars. However, scars from relatively minor wounds can also be stressful. The site of an open thyroidectomy is the anterior neck, a prominently exposed part of the body, where postoperative scarring can cause patients distress. The cosmetic outcome of the scar after thyroidectomy is of particular importance to women, who constitute the majority of patients with thyroid disease. Active prevention is more likely to yield better cosmetic results and would require fewer treatment sessions and less expense than scar revision procedures. Many interventions have been proposed, but there is yet no universal consensus on optimal treatment. Recently, focus has been made on 'laser scar prevention', where various types of lasers have been used to improve the appearance of scars. The purpose of this study was to improve the appearance of scars, by laser intervention of the wound healing process. In this pilot study, we comparatively examined the effect of non-ablative 1550-nm fractional Er: glass laser and ablative 2940-nm fractional Er: YAG laser on fresh surgical scars of patients with Fitzpatrick skin type III-IV.

  18. Comparison of holmium:YAG and thulium fiber laser lithotripsy: ablation thresholds, ablation rates, and retropulsion effects.

    PubMed

    Blackmon, Richard L; Irby, Pierce B; Fried, Nathaniel M

    2011-07-01

    The holmium:YAG (Ho:YAG) laser lithotriptor is capable of operating at high pulse energies, but efficient operation is limited to low pulse rates (∼10 Hz) during lithotripsy. On the contrary, the thulium fiber laser (TFL) is limited to low pulse energies, but can operate efficiently at high pulse rates (up to 1000 Hz). This study compares stone ablation threshold, ablation rate, and retropulsion for the two different Ho:YAG and TFL operation modes. The TFL (λ = 1908 nm) was operated with pulse energies of 5 to 35 mJ, 500-μs pulse duration, and pulse rates of 10 to 400 Hz. The Ho:YAG laser (λ = 2120 nm) was operated with pulse energies of 30 to 550 mJ, 350-μs pulse duration, and a pulse rate of 10 Hz. Laser energy was delivered through 200- and 270-μm-core optical fibers in contact mode with human calcium oxalate monohydrate (COM) stones for ablation studies and plaster-of-Paris stone phantoms for retropulsion studies. The COM stone ablation threshold for Ho:YAG and TFL measured 82.6 and 20.8 J∕cm(2), respectively. Stone retropulsion with the Ho:YAG laser linearly increased with pulse energy. Retropulsion with TFL was minimal at pulse rates less than 150 Hz, then rapidly increased at higher pulse rates. For minimal stone retropulsion, Ho:YAG operation at pulse energies less than 175 mJ at 10 Hz and TFL operation at 35 mJ at 100 Hz is recommended, with both lasers producing comparable ablation rates. Further development of a TFL operating with both high pulse energies of 100 to 200 mJ and high pulse rates of 100 to 150 Hz may also provide an alternative to the Ho:YAG laser for higher ablation rates, when retropulsion is not a primary concern.

  19. Comparison of holmium:YAG and thulium fiber laser lithotripsy: ablation thresholds, ablation rates, and retropulsion effects

    NASA Astrophysics Data System (ADS)

    Blackmon, Richard L.; Irby, Pierce B.; Fried, Nathaniel M.

    2011-07-01

    The holmium:YAG (Ho:YAG) laser lithotriptor is capable of operating at high pulse energies, but efficient operation is limited to low pulse rates (~10 Hz) during lithotripsy. On the contrary, the thulium fiber laser (TFL) is limited to low pulse energies, but can operate efficiently at high pulse rates (up to 1000 Hz). This study compares stone ablation threshold, ablation rate, and retropulsion for the two different Ho:YAG and TFL operation modes. The TFL (λ = 1908 nm) was operated with pulse energies of 5 to 35 mJ, 500-μs pulse duration, and pulse rates of 10 to 400 Hz. The Ho:YAG laser (λ = 2120 nm) was operated with pulse energies of 30 to 550 mJ, 350-μs pulse duration, and a pulse rate of 10 Hz. Laser energy was delivered through 200- and 270-μm-core optical fibers in contact mode with human calcium oxalate monohydrate (COM) stones for ablation studies and plaster-of-Paris stone phantoms for retropulsion studies. The COM stone ablation threshold for Ho:YAG and TFL measured 82.6 and 20.8 J/cm2, respectively. Stone retropulsion with the Ho:YAG laser linearly increased with pulse energy. Retropulsion with TFL was minimal at pulse rates less than 150 Hz, then rapidly increased at higher pulse rates. For minimal stone retropulsion, Ho:YAG operation at pulse energies less than 175 mJ at 10 Hz and TFL operation at 35 mJ at 100 Hz is recommended, with both lasers producing comparable ablation rates. Further development of a TFL operating with both high pulse energies of 100 to 200 mJ and high pulse rates of 100 to 150 Hz may also provide an alternative to the Ho:YAG laser for higher ablation rates, when retropulsion is not a primary concern.

  20. Ablation experiment and threshold calculation of titanium alloy irradiated by ultra-fast pulse laser

    SciTech Connect

    Zheng, Buxiang; Jiang, Gedong; Wang, Wenjun Wang, Kedian; Mei, Xuesong

    2014-03-15

    The interaction between an ultra-fast pulse laser and a material's surface has become a research hotspot in recent years. Micromachining of titanium alloy with an ultra-fast pulse laser is a very important research direction, and it has very important theoretical significance and application value in investigating the ablation threshold of titanium alloy irradiated by ultra-fast pulse lasers. Irradiated by a picosecond pulse laser with wavelengths of 1064 nm and 532 nm, the surface morphology and feature sizes, including ablation crater width (i.e. diameter), ablation depth, ablation area, ablation volume, single pulse ablation rate, and so forth, of the titanium alloy were studied, and their ablation distributions were obtained. The experimental results show that titanium alloy irradiated by a picosecond pulse infrared laser with a 1064 nm wavelength has better ablation morphology than that of the green picosecond pulse laser with a 532 nm wavelength. The feature sizes are approximately linearly dependent on the laser pulse energy density at low energy density and the monotonic increase in laser pulse energy density. With the increase in energy density, the ablation feature sizes are increased. The rate of increase in the feature sizes slows down gradually once the energy density reaches a certain value, and gradually saturated trends occur at a relatively high energy density. Based on the linear relation between the laser pulse energy density and the crater area of the titanium alloy surface, and the Gaussian distribution of the laser intensity on the cross section, the ablation threshold of titanium alloy irradiated by an ultra-fast pulse laser was calculated to be about 0.109 J/cm{sup 2}.

  1. Effects of Liquid Medium and Ablation Wavelength on the Properties of Cadmium Sulfide Nanoparticles Formed by Pulsed-Laser Ablation.

    PubMed

    García Guillén, Grisel; Zuñiga Ibarra, Veronica Anahi; Mendivil Palma, Maria Isabel; Krishnan, Bindu; Avellaneda Avellaneda, David; Shaji, Sadasivan

    2016-11-03

    Pulsed-laser ablation in liquid (PLAL) is a green synthesis technique to obtain semiconductor nanomaterials in colloidal form. Herein, cadmium sulfide (CdS) nanoparticles were synthesized by the pulsed-laser ablation of a CdS target in different liquid media by using λ=532 and 1064 nm outputs from a pulsed (10 ns, 10 Hz) Nd:YAG laser at different ablation fluence values. The morphology, structure, crystalline phase, elemental composition, optical, and luminescent properties of CdS nanomaterials were analyzed by using transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV/Vis absorption spectroscopy, and fluorescence spectroscopy. By changing the liquid medium and ablation wavelength, CdS nanoparticles with different morphology and size were formed, as demonstrated by using TEM analysis. The crystallinity and chemical states of the ablation products were confirmed by using XRD and XPS analyses. The optical bandgap of the CdS nanoparticles was dependent on the ablation wavelength and the fluence. These nanocolloids presented different green emissions, which implied the presence of several emission centers. CdS nanocolloids in distilled water catalyzed the photocatalytic decay of methylene blue dye under light irradiation from a solar simulator.

  2. Cavitation dynamics of laser ablation of bulk and wire-shaped metals in water during nanoparticles production.

    PubMed

    De Giacomo, A; Dell'Aglio, M; Santagata, A; Gaudiuso, R; De Pascale, O; Wagener, P; Messina, G C; Compagnini, G; Barcikowski, S

    2013-03-07

    Although the first nanoseconds to microseconds rule the resulting process yield of laser ablation in liquid, a comprehensive view involving combination of time-resolved measurement techniques is still lacking. In this paper, fundamental aspects of laser ablation of metals in water during the production of nanoparticles are discussed. Three fast diagnostic methods have been applied simultaneously. These are Optical Emission Spectroscopy for the plasma characterization, fast shadowgraph for plasma and cavitation bubble dynamics and laser scattering for the mechanisms of delivery of the produced materials in the liquid. Moreover, in order to validate the discussion, the effect on cavitation dynamics of the ablation of bulk and wire-shaped targets has been investigated together with the relative nanoparticles production yield. Unusual arrow-bow ejection phenomena between the cavitation bubble and the wire result in suppressed material back-deposition, causing efficient ejection of ablated matter into the liquid. The presented nanosecond and microsecond-resolved analysis allows estimating the timescale and role of the basic mechanisms involved in laser ablation in liquids as well as the thermodynamic characteristics of the processes.

  3. Laser Ablation of Dental Calculus Around 400 nm Using a Ti:Sapphire Laser

    SciTech Connect

    Schoenly, J.; Seka, W.; Rechmann, P.

    2009-10-19

    A Nd:YAG laser-pumped, frequency-doubled Ti:sapphire laser is used for selective ablation of calculus. The laser provides ≤25 mJ at 400 nm (60-ns pulse width, 10-Hz repetition rate). The laser is coupled into an optical multimode fiber coiled around a 4-in.-diam drum to generate a top-hat output intensity profile. With coaxial water cooling, this is ideal for efficient, selective calculus removal. This is in stark contrast with tightly focused Gaussian beams that are energetically inefficient and lead to irreproducible results. Calculus is well ablated at high fluences ≥2 J/cm^2; stalling occurs below this fluence because of photobleaching. Healthy hard tissue is not removed at fluences ≤3 J/cm^2.

  4. Characterization of laser ablation of carbon-doped glycerol at different laser wavelengths

    NASA Astrophysics Data System (ADS)

    Zheng, Z. Y.; Zhang, S. Q.; Liang, T.; Tang, W. C.; Xiao, K.; Liang, W. F.; Gao, L.; Gao, H.; Xing, J.; Wu, X. W.; Zhang, Z. L.

    2016-12-01

    Laser ablation of carbon-doped glycerol at laser wavelengths of 1064 and 532 nm are characterized in laser plasma propulsion. The coupling coefficient, specific impulse and the plasma luminescence are measured. It is found that the coupling coefficient and the specific impulse are much related to the wavelength and the carbon content. A long wavelength and a high carbon content can enhance the coupling coefficient and specific impulse due to the prolonging coupling time of laser pulse with plasma. However, an optimal propulsion also relates with the un-ionized splashing liquids.

  5. EUV nanosecond laser ablation of silicon carbide, tungsten and molybdenum

    NASA Astrophysics Data System (ADS)

    Frolov, Oleksandr; Kolacek, Karel; Schmidt, Jiri; Straus, Jaroslav; Choukourov, Andrei; Kasuya, Koichi

    2015-09-01

    In this paper we present results of study interaction of nanosecond EUV laser pulses at wavelength of 46.9 nm with silicon carbide (SiC), tungsten (W) and molybdenum (Mo). As a source of laser radiation was used discharge-plasma driver CAPEX (CAPillary EXperiment) based on high current capillary discharge in argon. The laser beam is focused with a spherical Si/Sc multilayer-coated mirror on samples. Experimental study has been performed with 1, 5, 10, 20 and 50 laser pulses ablation of SiC, W and Mo at various fluence values. Firstly, sample surface modification in the nanosecond time scale have been registered by optical microscope. And the secondly, laser beam footprints on the samples have been analyzed by atomic-force microscope (AFM). This work supported by the Czech Science Foundation under Contract GA14-29772S and by the Grant Agency of the Ministry of Education, Youth and Sports of the Czech Republic under Contract LG13029.

  6. Endometrial ablation using SideFire laser fiber

    NASA Astrophysics Data System (ADS)

    Everett, Royice B.

    1996-05-01

    The first successful report using the neodymium:yttrium-aluminum-garnet (Nd:YAG) Laser to control hypermenorrhea was reported in 1981. Variations on the treatment technique have been attempted to improve the amenorrhea rate. Reports using the Nd:YAG laser with the blanching or non-touch technique seem to result in a better outcome and higher rate of total amenorrhea than using the dragging technique. Due to the report of improved rates of amenorrhea when using the blanching technique and the Nd:YAG laser, a fiber was developed to direct the laser energy at right angles to the axis of the fiber, therefore allowing a total treatment of the entire uterus in a perpendicular fashion. The theoretic benefit of this would be a more complete and predictable destruction of the endometrial lining, avoiding fluid overload by coagulating and sealing of the vessels and lymphatic. After a follow-up of 12 to 36 months, 56 of the 60 patients (93%) who underwent complete endometrial ablation with the SideFireTM technique had excellent results. Total absolute amenorrhea resulted in 50 patients (83%). Contrary to earlier reports, using the rollerball electrode, this procedure technique resulted in no decrease in results in younger patients. In conclusion, this seems to be a reasonable alternative which offers improved results when compared to previously available methods using electrosurgery or the Nd:YAG laser without the use of the SideFireTM device.

  7. Positioning for Endovenous Laser Ablation: Comparative Study with Thigh Stripping

    PubMed Central

    Masaki, Hisao; Yunoki, Yasuhiro; Watanabe, Yoshiko; Furukawa, Hiroshi; Yamasawa, Takahiko; Takiuchi, Hiroki; Honda, Takeshi; Kuwada, Noriaki; Kojima, Kenji; Tanemoto, Kazuo

    2016-01-01

    We performed a comparative study of surgical outcomes and venous functions between endovenous laser ablation with a 980-nm diode laser (EV group) and thigh stripping (ST group). There were no severe complications and initial success rates were 100% in both groups. In the EV group, preoperative symptoms improved in 94.3% of cases, the venous occlusion rate was 98%, and endovenous heat induced thrombosis had occurred in 11.9% (Class 3: 0.7%) at 12 months after the operation. Although comparative study of postoperative venous function by air plethysmography showed significant improvement in both groups, there was less recovery of postoperative venous function in the EV than in the ST group. (This article is a translation of J Jpn Coll Angiol 2015; 55: 13–20.) PMID:27738455

  8. Laser ablation and competitive technologies in paint stripping of heavy anticorrosion coatings

    NASA Astrophysics Data System (ADS)

    Schuöcker, Georg D.; Bielak, Robert

    2007-05-01

    During the last years surface preparation prior to coating operations became an important research and development task, since tightened environmental regulations have to be faced in view of the deliberation of hazardous compounds of coatings. Especially, ship-yards get more and more under pressure, because the environmental commitment of their Asian competitors is fairly limited. Therefore, in the US and in Europe several technology evaluation projects have been launched to face this challenge. The majority of coating service providers and ship yards use grit blasting; this process causes heavy emissions as of dust and enormous amounts of waste as polluted sand. Coating removal without any blasting material would reduce the environmental impact. Laser processing offers ecological advantages. Therefore thermal processes like laser ablation have been studied thoroughly in several published projects and also in this study. Many of these studies have been focused on the maintenance of airplanes, but not on de-coating of heavy protective coatings. In this case the required laser power is extra-high. This study is focused on the maintenance of heavy anti-corrosion coatings and compares the industrial requirements and the opportunities of the innovative laser processes. Based on the results of this analysis similar approaches as e.g. plasma jet coating ablation have been studied. It was concluded that none of these methods can compete economically with the conventional processes as grit blasting and water jetting since the required ablation rate is very high (>60m2/h). A new process is required that is not based on any blasting operation and which does not depend strongly on the coating's characteristic. The delamination of the coating where the coatings is not removed by evaporation, but in little pieces of the complete coating system meets these requirements. The delamination can be accomplished by the thermal destruction of the primer coating by an intense heat pulse

  9. Laser Direct Ablation of Indium Tin Oxide Films on Both Sides of Various Substrates.

    PubMed

    Oh, Gi Taek; Kwon, Sang Jik; Han, Jae-Hee; Cho, Eou Sik

    2015-03-01

    We demonstrate ablation of indium tin oxide (ITO) films onto both glass and polyethylene terephthalate (PET) substrates, using a Q-switched diode-pumped neodymium-doped yttrium vanadate laser (Nd:YVO4, λ = 1064 nm) incident on both the front and back sides of the substrate. From scanning electron microscope (SEM) images and depth profile data, ITO patterns that were laser-ablated onto glass from the back side showed a larger abrupt change in the ablated line width than those ablated from the front. However, there were only slight differences in ablated line widths due to the direction of the incident laser beam. We provide a possible explanation in terms of several factors: dispersion of laser beam energy through the substrate, overlapping of each laser beam spot due to scanning speed, and the thickness of glass and PET substrates.

  10. Laser ablation with resonance ionization for determination of hydrogen in zirconium

    NASA Astrophysics Data System (ADS)

    Bickel, Grant A.; McRae, Glenn A.; Green, Lawrence W.

    1993-10-01

    Corrosion and hydrogen ingress in zirconium alloys can lead to hydride blister formation at localized areas and possible delayed hydride cracking. Laser ablation is being investigated in our laboratory as a method to determine the content with the 1.06 μm or 355 nm output of a Nd:YAG laser. The elemental H and D in the ablation plume are detected in a time-of-flight mass spectrometer following photo-ionization via the two-photon resonance near 243 nm. The ablation is accurately described by a simple laser-heating model for fluences below 3 J/cm2 at beam center. Ablation rates were found to range from a few to hundreds of Å per shot, varying exponentially with fluence. Laser ablation depth profiling in thin oxide films has yielded qualitative information about the H distribution. Various surface techniques such as Nuclear Reaction Analysis (NRA) and laser profilometry are used to support these conclusions.

  11. Laser ablation of basal cell carcinomas guided by confocal microscopy

    NASA Astrophysics Data System (ADS)

    Sierra, Heidy; Cordova, Miguel; Nehal, Kishwer; Rossi, Anthony; Chen, Chih-Shan Jason; Rajadhyaksha, Milind

    2016-02-01

    Laser ablation offers precise and fast removal of superficial and early nodular types of basal cell carcinomas (BCCs). Nevertheless, the lack of histological confirmation has been a limitation. Reflectance confocal microscopy (RCM) imaging combined with a contrast agent can offer cellular-level histology-like feedback to detect the presence (or absence) of residual BCC directly on the patient. We conducted an ex vivo bench-top study to provide a set of effective ablation parameters (fluence, number of passes) to remove superficial BCCs while also controlling thermal coagulation post-ablation to allow uptake of contrast agent. The results for an Er:YAG laser (2.9 um and pulse duration 250us) show that with 6 passes of 25 J/cm2, thermal coagulation can be effectively controlled, to allow both the uptake of acetic acid (contrast agent) and detection of residual (or absence) BCCs. Confirmation was provided with histological examination. An initial in vivo study on 35 patients shows that the uptake of contrast agent aluminum chloride) and imaging quality is similar to that observed in the ex vivo study. The detection of the presence of residual tumor or complete clearance was confirmed in 10 wounds with (additional) histology and in 25 lesions with follow-up imaging. Our results indicate that resolution is sufficient but further development and use of appropriate contrast agent are necessary to improve sensitivity and specificity. Advances in RCM technology for imaging of lateral and deep margins directly on the patient may provide less invasive, faster and less expensive image-guided approaches for treatment of BCCs.

  12. Single droplet separations and surface partition coefficient measurements using laser ablation mass spectrometry

    PubMed Central

    Jorabchi, Kaveh; Smith, Lloyd M.

    2010-01-01

    Surface activity of analytes plays a significant role in many chemical and physical phenomena. We present here a mass spectrometric method to characterize surface activity and solute partitioning between bulk liquid and the gas-liquid interface in droplets. The approach employs ablation by an IR laser from the surface of a microliter droplet deposited on a stainless steel post. The ablated material is ionized for mass spectrometric analysis by either droplet charging or by post-ionization in an electrospray plume. Three areas of application have been explored using this method; 1) separations in a single droplet: continuous ablation by a series of many successive laser pulses results in faster depletion of more surface active analytes, effectively comprising a surface activity-based separation. 2) Partition coefficient measurements: droplet volume is held constant during ablation by continually replenishing lost solvent. This leads to analyte-specific ion signal decay curves that may be fitted to a model based on Langmuir adsorption isotherms and simple analytical expressions, yielding quantitative values for the analyte surface partition coefficients. 3) Studies of the relationship between surface partitioning and HPLC phase partitioning: comparisons of surface activities measured by laser desorption with retention times in reversed phase HPLC reveal that the relationship between the two partitioning processes is very sensitive to chemical structure. Poor correlation between the retention time and surface activity is also observed within a subcategory of analytes (peptides). This effect is attributed to multi-modal solute-stationary phase interactions. The laser desorption approach presented here provides direct information on analyte surface activities free from the complications encountered in chromatographic methods due to chemical structure variations. PMID:19886638

  13. Photonic Doppler velocimetry of laser-ablated ultrathin metals.

    PubMed

    Valenzuela, A R; Rodriguez, G; Clarke, S A; Thomas, K A

    2007-01-01

    Obtaining velocity information from the interaction of a laser pulse on a metal layer provides insight into the rapid dynamics of material removal and plasma plume physics during ablation. A traditional approach involves using a velocity interferometer system for any reflector (VISAR) on a reflective metal surface. However, when the target is a thin metal layer, the cohesion of the surface is quickly lost resulting in a large spread of particle velocities that cannot be easily resolved by VISAR. This is due to material ejection"confusing" the VISAR measurement surface, effectively washing out the spatial fringe visibility in the VISAR interferometer. A new heterodyne-based optical velocimeter method is the photonic Doppler velocimeter (PDV). Because PDV tracks motion in a frequency encoded temporal electro-optical signal, velocity information is preserved and allows for multiple velocity components to be recorded simultaneously. The challenge lies in extracting PDV velocity information at short (nanosecond) laser ablation time scales with rapidly varying heterodyne beats by using electronic, optical, and analytical techniques to recover the velocity information from a fleeting signal. Here we show how we have been able to obtain velocity information on the nanosecond time scale and are able to compare it to hydrodynamic simulations. Also, we examine refinements to our PDV system by increasing the bandwidth, utilizing different probes, and sampling different analysis techniques.

  14. Neutral atomic jet generation by laser ablation of copper targets

    SciTech Connect

    Matos, J. B. de; Rodrigues, N. A. S.

    2014-08-15

    This work aimed the obtainment of a neutral atomic jet departing from a plume generated by laser ablation of copper targets. A pair of electrodes together with a transducer pressure sensor was used to study the ablated plume charge composition and also to measure the ion extraction from the plasma plume. The neutral beam was produced with this setup and the relative abundance of neutrals in the plasma was measured, it decreases from 30% to 8% when the laser fluence is varied from 20 J/cm{sup 2} to 32 J/cm{sup 2}. The necessary voltage to completely remove the ions from the plume varied from 10 V to 230 V in the same fluence range. TOF analysis resulted in center of mass velocities between 3.4 and 4.6 km/s, longitudinal temperature in the range from 1 × 10{sup 4} K to 2.4 × 10{sup 4} K and a Mach number of M = 2.36, calculated using purely hydrodynamic expansion approximation.

  15. Photonic Doppler velocimetry of laser-ablated ultrathin metals

    SciTech Connect

    Valenzuela, A. R.; Rodriguez, G.; Clarke, S. A.; Thomas, K. A.

    2007-01-15

    Obtaining velocity information from the interaction of a laser pulse on a metal layer provides insight into the rapid dynamics of material removal and plasma plume physics during ablation. A traditional approach involves using a velocity interferometer system for any reflector (VISAR) on a reflective metal surface. However, when the target is a thin metal layer, the cohesion of the surface is quickly lost resulting in a large spread of particle velocities that cannot be easily resolved by VISAR. This is due to material ejection 'confusing' the VISAR measurement surface, effectively washing out the spatial fringe visibility in the VISAR interferometer. A new heterodyne-based optical velocimeter method is the photonic Doppler velocimeter (PDV). Because PDV tracks motion in a frequency encoded temporal electro-optical signal, velocity information is preserved and allows for multiple velocity components to be recorded simultaneously. The challenge lies in extracting PDV velocity information at short (nanosecond) laser ablation time scales with rapidly varying heterodyne beats by using electronic, optical, and analytical techniques to recover the velocity information from a fleeting signal. Here we show how we have been able to obtain velocity information on the nanosecond time scale and are able to compare it to hydrodynamic simulations. Also, we examine refinements to our PDV system by increasing the bandwidth, utilizing different probes, and sampling different analysis techniques.

  16. Laser ablation molecular isotopic spectrometry of carbon isotopes

    NASA Astrophysics Data System (ADS)

    Bol‧shakov, Alexander A.; Mao, Xianglei; Jain, Jinesh; McIntyre, Dustin L.; Russo, Richard E.

    2015-11-01

    Quantitative determination of carbon isotopes using Laser Ablation Molecular Isotopic Spectrometry (LAMIS) is described. Optical emission of diatomic molecules CN and C2 is used in these measurements. Two quantification approaches are presented: empirical calibration of spectra using a set of reference standards and numerical fitting of a simulated spectrum to the experimental one. Formation mechanisms of C2 and CN in laser ablation plasma are briefly reviewed to provide insights for implementation of LAMIS measurements. A simulated spectrum of the 12C2 Swan system was synthesized using four constituents within 473.5-476.5 nm. Simulation included three branches of 12C2 (1-0), branches R(0-0) and R(1-1), and branch P(9-8) of 12C2. Spectral positions of the tail lines in R(0-0) and R(1-1) were experimentally measured, since they were not accurately known before. The Swan band (1-0) of the isotopologue 13C12C was also simulated. Fitting to the experimental spectrum yielded the ratio 13C/12C = 1.08% in a good agreement with measurements by isotope ratio mass spectrometry. LAMIS promises to be useful in coal, oil and shale exploration, carbon sequestration monitoring, and agronomy studies.

  17. Pulsed Laser Processing of Paper Materials

    NASA Astrophysics Data System (ADS)

    Schechtel, Florian; Reg, Yvonne; Zimmermann, Maik; Stocker, Thomas; Knorr, Fabian; Mann, Vincent; Roth, Stephan; Schmidt, Michael

    At present the trends in paper and packaging industries are the personalization of products and the use of novel high-tech materials. Laser processes as non-contact and flexible techniques seem to be the obvious choice to address those developments. In this paper we present a basic understanding of the occurring mechanisms of laser based engraving of different paper and paperboard materials, using a picosecond laser source at 1064 nm. The influences on the beam-paper-interaction of grammage, the composition of the paper matrix, as well as the paper inherent cellulose fibers were investigated. Here the ablation threshold of commercially available paper was determined and a matrix ablation effect under the 1064 nm radiation observed. These results were characterized and qualified mainly by means of laser scanning microscope (LSM) micrographs in combination with color-space analytics.

  18. Comparison of Laser Chemical Processing and LaserMicroJet for structuring and cutting silicon substrates

    NASA Astrophysics Data System (ADS)

    Hopman, Sybille; Fell, Andreas; Mayer, Kuno; Mesec, Matthias; Rodofili, Andreas; Kray, Daniel

    2009-06-01

    This paper deals with the development of a new cutting method for thin silicon solar wafers with liquid-jet-guided lasers (LaserMicroJet®, LMJ, and Laser Chemical Processing, LCP). Several laser systems with different wavelengths were tested to find the optimum laser system and processing parameters in terms of efficient material removal and deep laser cutting. Water and potassium hydroxide were used as carrier liquids to enhance laser ablation. The ablation efficiency was defined as a target parameter and experimentally determined by performing single laser grooves. It is demonstrated that the ablation process of LMJ is mainly affected by silicon melting and then removing by the liquid-jet momentum for single laser grooves. Best result for deep laser grooves is achieved if evaporation dominates the ablation process. Better surface quality referred to laser-induced crystalline damage is presented for a cut wafer with LMJ in comparison to a standard multiwire slurry saw. This shows a great potential of wafering with liquid-jet-guided lasers although no optimal liquid media was used.

  19. Experimental study on 800 nm femtosecond laser ablation of fused silica in air and vacuum

    NASA Astrophysics Data System (ADS)

    Xu, Shi-zhen; Yao, Cai-zhen; Liao, Wei; Yuan, Xiao-dong; Wang, Tao; Zu, Xiao-tao

    2016-10-01

    Ablation rates of fused silica were studied as a function of femtosecond laser pulse fluences (0.7-41 J/cm2) in air and vacuum. The experiment was conducted by using a Ti:sapphire laser that emits radiation at 800 nm with a pulse width of 35 fs and a repetition rate of 10 Hz. The morphology and ablation depth of laser-induced damage crater were evaluated by using optical microscopy and scanning electron microscopy (SEM). Ablation rates were calculated from the depth of craters induced by multiple laser pulses. Results showed that two ablation regimes, i.e. non-thermal and thermal ablation co-existed in air and vacuum at low and moderate fluences. A drop of ablation rate was observed at high fluence (higher than 9.5 J/cm2) in air. While in vacuum, the ablation rate increased continuously with the increasing of laser fluence and much higher than that in air. The drop of ablation rate observed at high fluence in air was due to the strong defocusing effects associated with the non-equilibrium ionization of air. Furthermore, the laser-induced damage threshold (LIDT), which was determined from the relationship between crater area and the logarithm of laser energy, was found to depend on the number of incident pulses on the same spot, and similar phenomenon was observed in air and vacuum.

  20. Femtosecond laser ablation with single and two-photon excitation for MEMS

    NASA Astrophysics Data System (ADS)

    Elbandrawy, Mohamed Abdelfattah Kottb Ahmad

    There is an increasing interest in femtosecond laser micromachining of materials because of the femtosecond laser's unique high peak power, ultrashort pulse width, negligible heat conductivity process during the laser pulse, and the minimal heat affected zone, which is in the same order of magnitude of the ablated submicron spot. There are some obstacles in reaching optimal and reliable micromachining parameters. One of these obstacles is the lack of understanding of the nature of the interaction and related physical processes. These processes include amorphization, melting, re-crystallization, nucleated-vaporization, and ablation. The focus of this Dissertation was to study the laser-matter interaction with single and two-photon excitation for optical micro-electro-mechanical system (OMEMS) applications. The laser pulse interaction mechanism was studied by performing a series of experiments including self-imaging experiments, two-photon absorption measurements, and micromachining processes characterizations. As a result of the self-imaging experiment, it was found for both Si and GaP that the material surface reflectivity increased twice as much during the action of the laser pulse. The generation of electron-hole plasma of 10 22cm-3 density was assigned to be responsible for the reflectivity jump. The Drude damping time of the generated plasma was determined to be 0.35 fs for silicon and 0.27 fs for gallium phosphate. Additionally, a precise measurement of the two-photon absorption (TPA) coefficient (beta) was done. The TPA coefficient was found to be 0.2 cm/GW. Experimental results were in good agreement with the theoretical expectations up to a point at which the ablation started kicking off and the plasma absorption took place. In case of a single pulse interaction with silicon, self-assembled nano-filaments of a few tens of microns' length and about 100 nm width were observed for the first time with the femtosecond single pulse interaction. The filaments were

  1. Particle Generation by Pulsed Excimer Laser Ablation in Liquid: Hollow Structures and Laser-Induced Reactions

    NASA Astrophysics Data System (ADS)

    Yan, Zijie

    2011-12-01

    Pulsed laser ablation of solid targets in liquid media is a powerful method to fabricate micro-/nanoparticles, which has attracted much interest in the past decade. It represents a combinatorial library of constituents and interactions, and one can explore disparate regions of parameter space with outcomes that are impossible to envision a priori. In this work, a pulsed excimer laser (wavelength 248 nm, pulse width 30 ns) has been used to ablate targets in liquid media with varying laser fluences, frequencies, ablation times and surfactants. It is observed that hollow particles could be fabricated by excimer laser ablation of Al, Pt, Zn, Mg, Ag, Si, TiO2, and Nb2O5 in water or aqueous solutions. The hollow particles, with sizes from tens of nanometers to micrometers, may have smooth and continuous shells or have morphologies demonstrating that they were assembled from nanoparticles. A new mechanism has been proposed to explain the formation of these novel particle geometries. They were formed on laser-produced bubbles through bubble interface pinning by laser-produced solid species. Considering the bubble dynamics, thermodynamic and kinetic requirements have been discussed in the mechanism that can explain some phenomena associated with the formation of hollow particles, especially (1) larger particles are more likely to be hollow particles; (2) Mg and Al targets have stronger tendency to generate hollow particles; and (3) the 248 nm excimer laser is more beneficial to fabricate hollow particles in water than other lasers with longer wavelengths. The work has also demonstrated the possiblities to fabricate novel nanostructures through laser-induced reactions. Zn(OH)2/dodecyl sulfate flower-like nanostructures, AgCl cubes, and Ag2O cubes, pyramids, triangular plates, pentagonal rods and bars have been obtained via reactions between laser-produced species with water, electrolyes, or surfactant molecules. The underlying mechanisms of forming these structures have been

  2. Carbon isotope separation and molecular formation in laser-induced plasmas by laser ablation molecular isotopic spectrometry.

    PubMed

    Dong, Meirong; Mao, Xianglei; Gonzalez, Jhanis J; Lu, Jidong; Russo, Richard E

    2013-03-05

    Laser ablation molecular isotopic spectrometry (LAMIS) recently was reported for rapid isotopic analysis by measuring molecular emission from laser-induced plasmas at atmospheric pressure. This research utilized the LAMIS approach to study C2 molecular formation from laser ablation of carbon isotopic samples in a neon gas environment at 0.1 MPa. The isotopic shift for the Swan system of the C2 Δν = 1 band was chosen for carbon isotope analysis. Temporal and spatial resolved measurements of (12)C2, (12)C(13)C, and (13)C2 show that C2 forms from recombination reactions in the plasma. A theoretical simulation was used to determine the temperature from the molecular bands and to extract the isotopic ratio of (12)C/(13)C derived from (12)C2, (12)C(13)C, and (13)C2. Our data show that the ratio of (12)C/(13)C varies with time after the laser pulse and with distance above the sample. (12)C/(13)C deviates from the nominal ratio (2:1) at early times and closest to the sample surface. These measurements provide understanding of the chemical processes in the laser plasma and analytical improvement using LAMIS.

  3. Minimizing matrix effect by femtosecond laser ablation and ionization in elemental determination.

    PubMed

    Zhang, Bochao; He, Miaohong; Hang, Wei; Huang, Benli

    2013-05-07

    Matrix effect is unavoidable in direct solid analysis, which usually is a leading cause of the nonstoichiometric effect in quantitative analysis. In this research, experiments were carried out to study the overall characteristics of atomization and ionization in laser-solid interaction. Both nanosecond (ns) and femtosecond (fs) lasers were applied in a buffer-gas-assisted ionization source coupled with an orthogonal time-of-flight mass spectrometer. Twenty-nine solid standards of ten different matrices, including six metals and four dielectrics, were analyzed. The results indicate that the fs-laser mode offers more stable relative sensitivity coefficients (RSCs) with irradiance higher than 7 × 10(13) W·cm(-2), which could be more reliable in the determination of element composition of solids. The matrix effect is reduced by half when the fs-laser is employed, owing to the fact that the fs-laser ablation and ionization (fs-LAI) incurs an almost heat-free ablation process and creates a dense plasma for the stable ionization.

  4. Microchannel fabrication on cyclic olefin polymer substrates via 1064 nm Nd:YAG laser ablation

    NASA Astrophysics Data System (ADS)

    McCann, Ronán; Bagga, Komal; Groarke, Robert; Stalcup, Apryll; Vázquez, Mercedes; Brabazon, Dermot

    2016-11-01

    This paper presents a method for fabrication of microchannels on cyclic olefin polymer films that have application in the field of microfluidics and chemical sensing. Continuous microchannels were fabricated on 188-μm-thick cyclic olefin polymer substrates using a picosecond pulsed 1064 nm Nd:YAG laser. The effect of laser fluence on the microchannel morphology and dimensions was analysed via scanning electron microscopy and optical profilometry. Single laser passes were found to produce v-shaped microchannels with depths ranging from 12 μm to 47 μm and widths from 44 μm to 154 μm. The ablation rate during processing was lower than predicted theoretically. Multiple laser passes were applied to examine the ability for finer control over microchannel morphology with channel depths ranging from 22 μm to 77 μm and channel widths from 59 μm to 155 μm. For up to five repeat passes, acceptable reproducibility was found in the produced microchannel morphology. Infrared spectroscopy revealed oxidation and dehydrogenation of the polymer surface following laser ablation. These results were compared to other work conducted on cyclic olefin polymers.

  5. 3D photomechanical model of tooth enamel ablation by Er-laser radiation

    NASA Astrophysics Data System (ADS)

    Belikov, Andrey V.; Shatilova, Ksenia V.; Skrypnik, Alexei V.

    2014-02-01

    The three-dimensional (3D) photomechanical model of human tooth enamel ablation is described. It takes into account: the structural peculiarities of enamel, Er-laser beam energy spatial distribution and laser radiation attenuation in the tissue. Dynamics change of enamel coefficient of absorption during ablation is also discussed. We consider the 3D photomechanical model of incomplete removal (modification) of the enamel rods by the pressure of water contained in the enamel pores and heated by laser radiation, and complete removal (ablation) of the enamel rods as result of hydroxyapatite heated by laser radiation and evaporation. Modeling results are in close agreement with the experimental results.

  6. KrF pulsed laser ablation of thin films made from fluorinated heterocyclic poly(naphthyl-imide)s.

    PubMed

    Damaceanu, Mariana-Dana; Rusu, Radu-Dan; Olaru, Mihaela Adriana; Timpu, Daniel; Bruma, Maria

    2012-06-01

    Among the many aspects of laser ablation, development of conical structures induced by excimer laser radiation on polyimide surfaces has been thoroughly investigated. Because the mechanisms that produce these surface textures are not fully understood, two theories, photochemical bond breaking and thermal reaction, have been introduced. Here we present the first study of ultraviolet laser ablation behavior of thin films made from fluorinated poly(naphthyl-imide)s containing oxadiazole rings and the investigation of the mechanism of cone-like structure formation at two laser fluences, 57 and 240 mJ/cm(2). The morphology of thin films before and after laser ablation was studied by using various spectroscopy techniques such as Fourier transform infrared spectroscopy, time-resolved emission and X-ray photoelectron spectroscopy, atomic force microscopy, and contact angle measurements. All of the data suggest impurities shielded at low fluence radiation (57 mJ/cm(2)) and a radiation hardening process at high value fluence (240 mJ/cm(2)), which are proposed as the main mechanisms for laser ablation of our polyimide films, and we bring evidence to support them.

  7. Photothermal ablation of liver tissue with 1940-nm thulium fiber laser: an ex vivo study on lamb liver

    NASA Astrophysics Data System (ADS)

    Alagha, Heba Z.; Gülsoy, Murat

    2016-01-01

    The purpose of this study was to investigate the ablation efficiency of 1940-nm thulium fiber laser on liver tissue, while utilizing a real-time measurement system to monitor the temperature rise in adjacent tissues. Thulium fiber laser was delivered to lamb liver tissue samples via 400-μm bare tip fiber in contact mode. Eight different laser parameter combinations [power, continuous-wave (cw)/pulsed-modulated (pm) mode, and exposure time] were used. Exposure times were chosen to give the same total applied energy of 4 J for comparative purposes. Following laser irradiations, tissues were processed and stained with hematoxylin and eosin for macroscopic evaluation of ablation areas and total altered areas, and ablation efficiencies were calculated. Temperature of the nearby tissue at a distance of 1 mm from the fiber was measured, and rate of temperature change was calculated. A strong correlation between the rate of temperature change and ablation area was noted. Thermal effects increased with increasing power for both modes. The continuous-wave mode yielded higher ablation efficiencies than the pulse-modulated mode. Histological evaluation revealed a narrow vacuolization zone and negligible carbonization for higher-power values.

  8. Myocardial tissue ablation by single high-energy laser pulses for ELR and TMR

    NASA Astrophysics Data System (ADS)

    Theisen, Dirk; Brinkmann, Ralf; Stubbe, Hans-Martin; Birngruber, Reginald

    1999-02-01

    The objective of this study is to compare the ablation sites induced by two different laser and application systems for myocardial laser revascularization. One system used was an 800 W CO2 laser, which is clinically established for transmyocardial laser revascularization (TMR). The second system was a self-designed Holmium laser emitting single high energy pulses for the minimal invasive approach of endocardial laser revascularization (ELR), whereby the laser light is transmitted via optical fiber into the left ventricle to ablate the myocardial channels from the inside. The laser energy was applied to Polyacrylamide (PAA) as transparent tissue phantom and in water as blood phantom. The ablation dynamics were investigated by high speed flash photography recording a picture series of a single event. Reperfused ex- vivo porcine hearts were treated to quantify differences in the thermal-mechanical damage ranges by polarization light microscopy. Ablation dynamics in water revealed oscillatory changes of the axial length of the steam bubbles between 3 mm and 12 mm during the CO2 laser pulse. For the Holmium laser pulse a maximal axial and lateral length of 5 mm was observed. The lateral dimensions of the bubbles were maximal 1 mm with the CO2- and 3.5 mm with the Holmium laser system. In PAA bubbles also collapse during the laser pulse which affects the size of the ablated channels. Using 12 J Holmium laser pulses for ablation of PAA, channel depths around 7 mm were found. Single Holmium laser pulses demonstrate ablations comparable in size and thermal- mechanical collateral damage to those achieved with the standard CO2 laser. The results are very encouraging for single pulse ELR and demonstrate the potential of a catheter based minimal invasive procedure for laser heart reperfusion.

  9. Multi-criteria optimization in CO2 laser ablation of multimode polymer waveguides

    NASA Astrophysics Data System (ADS)

    Tamrin, K. F.; Zakariyah, S. S.; Sheikh, N. A.

    2015-12-01

    High interconnection density associated with current electronics products poses certain challenges in designing circuit boards. Methods, including laser-assisted microvia drilling and surface mount technologies for example, are being used to minimize the impacts of the problems. However, the bottleneck is significantly pronounced at bit data rates above 10 Gbit/s where losses, especially those due to crosstalk, become high. One solution is optical interconnections (OI) based on polymer waveguides. Laser ablation of the optical waveguides is viewed as a very compatible technique with ultraviolet laser sources, such as excimer and UV Nd:YAG lasers, being used due to their photochemical nature and minimal thermal effect when they interact with optical materials. In this paper, the authors demonstrate the application of grey relational analysis to determine the optimized processing parameters concerning fabrication of multimode optical polymer waveguides by using infra-red 10.6 μm CO2 laser micromachining to etch acrylate-based photopolymer (Truemode™). CO2 laser micromachining offers a low cost and high speed fabrication route needed for high volume productions as the wavelength of CO2 lasers can couple well with a variety of polymer substrates. Based on the highest grey relational grade, the optimized processing parameters are determined at laser power of 3 W and scanning speed of 100 mm/s.

  10. Femtosecond laser ablation of cemented carbides: properties and tribological applications

    NASA Astrophysics Data System (ADS)

    Dumitru, G.; Romano, V.; Weber, H. P.; Gerbig, Y.; Haefke, H.; Bruneau, S.; Hermann, J.; Sentis, M.

    Laser ablation with fs laser pulses was performed in air on cobalt cemented tungsten carbide by means of a Ti : sapphire laser (800 nm, 100 fs). Small and moderate fluences (2, 5, 10 J/cm2) and up to 5×104 pulses per irradiated spot were used to drill holes with aspect ratios up to 10. Cross-section cuts from laser-irradiated samples were produced and they were analysed with optical microscopy and SEM. EDX analyses were carried out on selected zones. Quasi-cylindrical holes were found for 2 J/cm2, whereas for 5 and 10 J/cm2 irregular shapes (lobes, bottoms wider than hole entrances) were found to occur after a given number of incident pulses. Layers with modified structure were evidenced at pore walls. SEM revealed a denser structure, while EDX analyses showed uniform and almost similar contents of W, C, and Co in these layers. As a direct application, patterning of coated WC-Co was carried out with 2 J/cm2 and 100 pulses per pore. The resulted surfaces were tribologically tested and these tests revealed an improved friction and wear behaviour.

  11. Proton extraction by laser ablation of transition metals

    NASA Astrophysics Data System (ADS)

    Velardi, L.; Delle Side, D.; Krása, J.; Nassisi, V.

    2014-07-01

    A study on the proton beams extraction from a plasma generated by pulsed laser ablation by targets containing transition metals is presented. The targets used were pure disks of titanium and tantalum and disks of TiH2, obtained by compression of TiH2 powder. The plasma was produced by means of a nanosecond excimer KrF laser operating at low irradiance (109-1010 W/cm2). The proton and ions emission was analyzed by the time-of-flight technique using a Faraday cup as ion collector. Studies on the produced protons and ions at different laser irradiances from 2 to 15 GW/cm2 were performed. The characterization showed that it is possible to obtain good proton fluxes from these targets, up to 1011 proton/pulse. The results obtained are very interesting if compared with those available in literature where proton fluxes per pulse ranging from 108 to 109 by hydride targets were obtained, at the same laser irradiances.

  12. Mid-IR enhanced laser ablation molecular isotopic spectrometry

    NASA Astrophysics Data System (ADS)

    Brown, Staci; Ford, Alan; Akpovo, Codjo A.; Johnson, Lewis

    2016-08-01

    A double-pulsed laser-induced breakdown spectroscopy (DP-LIBS) technique utilizing wavelengths in the mid-infrared (MIR) for the second pulse, referred to as double-pulse LAMIS (DP-LAMIS), was examined for its effect on detection limits compared to single-pulse laser ablation molecular isotopic spectrometry (LAMIS). A MIR carbon dioxide (CO2) laser pulse at 10.6 μm was employed to enhance spectral emissions from nanosecond-laser-induced plasma via mid-IR reheating and in turn, improve the determination of the relative abundance of isotopes in a sample. This technique was demonstrated on a collection of 10BO and 11BO molecular spectra created from enriched boric acid (H3BO3) isotopologues in varying concentrations. Effects on the overall ability of both LAMIS and DP-LAMIS to detect the relative abundance of boron isotopes in a starting sample were considered. Least-squares fitting to theoretical models was used to deduce plasma parameters and understand reproducibility of results. Furthermore, some optimization for conditions of the enhanced emission was achieved, along with a comparison of the overall emission intensity, plasma density, and plasma temperature generated by the two techniques.

  13. Interaction of a converging laser beam with a Ag colloidal solution during the ablation of a Ag target in water

    NASA Astrophysics Data System (ADS)

    Resano-Garcia, Amandine; Battie, Yann; Naciri, Aotmane En; Chaoui, Nouari

    2016-05-01

    We studied the nanosecond laser-induced shape modifications of Ag colloids exposed to a converging laser beam during the ablation of a Ag target in water. To this end, we performed a series of laser ablation experiments in which the laser energy was varied while all other parameters were kept constant. In addition to transmission electron microscopy (TEM), the shape distribution of the Ag nanoparticles was determined by modelling the extinction spectra of the final colloidal solutions using theoretical calculations based on shape distributed effective medium theory (SDEMT). From these calculations, two physical parameters named sphericity and dispersity were introduced and used to gauge the evolution of the shape distribution of the particles. As the laser energy on the target was increased from 5 to 20 mJ/pulse, an apparently abrupt modification of the shape distribution of the particles was evidenced by both TEM and SDEMT calculations. This change is explained in terms of competitive fragmentation, growth and reshaping processes. On the basis the heating-melting-vaporization model, we demonstrate how the competition between these processes, occurring at different locations of the converging beam, determines the shape distribution of the final product. We highlight the relevance of the fluence gradient along the beam path and the laser interaction volume on the laser-induced modifications of the suspended particles during the ablation process.

  14. Surface modification of biomaterials by pulsed laser ablation deposition and plasma/gamma polymerization

    NASA Astrophysics Data System (ADS)

    Rau, Kaustubh R.

    Surface modification of stainless-steel was carried out by two different methods: pulsed laser ablation deposition (PLAD) and a combined plasma/gamma process. A potential application was the surface modification of endovascular stents, to enhance biocompatibility. The pulsed laser ablation deposition process, had not been previously reported for modifying stents and represented a unique and potentially important method for surface modification of biomaterials. Polydimethylsiloxane (PDMS) elatomer was studied using the PLAD technique. Cross- linked PDMS was deemed important because of its general use for biomedical implants and devices as well as in other fields. Furthermore, PDMS deposition using PLAD had not been previously studied and any information gained on its ablation characteristics could be important scientifically and technologically. The studies reported here showed that the deposited silicone film properties had a dependence on the laser energy density incident on the target. Smooth, hydrophobic, silicone-like films were deposited at low energy densities (100-150 mJ/cm2). At high energy densities (>200 mJ/cm2), the films had an higher oxygen content than PDMS, were hydrophilic and tended to show a more particulate morphology. It was also determined that (1)the deposited films were stable and extremely adherent to the substrate, (2)silicone deposition exhibited an `incubation effect' which led to the film properties changing with laser pulse number and (3)films deposited under high vacuum were similar to films deposited at low vacuum levels. The mechanical properties of the PLAD films were determined by nanomechanical measurements which are based on the Atomic Force Microscope (AFM). From these measurements, it was possible to determine the modulus of the films and also study their scratch resistance. Such measurement techniques represent a significant advance over current state-of-the-art thin film characterization methods. An empirical model for

  15. Data Fitting to Study Ablated Hard Dental Tissues by Nanosecond Laser Irradiation

    PubMed Central

    Abdel-Daiem, A. M.; Ansari, M. Shahnawaze; Babkair, Saeed S.; Salah, Numan A.; Al-Mujtaba, A.

    2016-01-01

    Laser ablation of dental hard tissues is one of the most important laser applications in dentistry. Many works have reported the interaction of laser radiations with tooth material to optimize laser parameters such as wavelength, energy density, etc. This work has focused on determining the relationship between energy density and ablation thresholds using pulsed, 5 nanosecond, neodymium-doped yttrium aluminum garnet; Nd:Y3Al5O12 (Nd:YAG) laser at 1064 nanometer. For enamel and dentin tissues, the ablations have been performed using laser-induced breakdown spectroscopy (LIBS) technique. The ablation thresholds and relationship between energy densities and peak areas of calcium lines, which appeared in LIBS, were determined using data fitting. Furthermore, the morphological changes were studied using Scanning Electron Microscope (SEM). Moreover, the chemical stability of the tooth material after ablation has been studied using Energy-Dispersive X-Ray Spectroscopy (EDX). The differences between carbon atomic % of non-irradiated and irradiated samples were tested using statistical t-test. Results revealed that the best fitting between energy densities and peak areas of calcium lines were exponential and linear for enamel and dentin, respectively. In addition, the ablation threshold of Nd:YAG lasers in enamel was higher than that of dentin. The morphology of the surrounded ablated region of enamel showed thermal damages. For enamel, the EDX quantitative analysis showed that the atomic % of carbon increased significantly when laser energy density increased. PMID:27228169

  16. Low work function surface layers produced by laser ablation using short-wavelength photons

    DOEpatents

    Balooch, Mehdi; Dinh, Long N.; Siekhaus, Wigbert J.

    2000-01-01

    Short-wavelength photons are used to ablate material from a low work function target onto a suitable substrate. The short-wavelength photons are at or below visible wavelength. The elemental composition of the deposit is controlled by the composition of the target and the gaseous environment in which the ablation process is performed. The process is carried out in a deposition chamber to which a short-wavelength laser is mounted and which includes a substrate holder which can be rotated, tilted, heated, or cooled. The target material is mounted onto a holder that spins the target during laser ablation. In addition, the deposition chamber is provided with a vacuum pump, an external gas supply with atomizer and radical generator, a gas generator for producing a flow of molecules on the substrate, and a substrate cleaning device, such as an ion gun. The substrate can be rotated and tilted, for example, whereby only the tip of an emitter can be coated with a low work function material.

  17. Ablation of carbon-doped liquid propellant in laser plasma propulsion

    NASA Astrophysics Data System (ADS)

    Zheng, Z. Y.; Liang, T.; Zhang, S. Q.; Gao, L.; Gao, H.; Zhang, Z. L.

    2016-04-01

    Carbon-doped liquid glycerol ablated by nanosecond pulse laser is investigated in laser plasma propulsion. It is found that the propulsion is much more correlated with the carbon content. The doped carbon can change the laser intensity and laser focal position so as to reduce the splashing quantity of the glycerol. Less consumption of the liquid volume results in a high specific impulse.

  18. Atomistic investigation of ablation of amorphous polystyrene under femtosecond laser pulse

    NASA Astrophysics Data System (ADS)

    Huang, YanHua; Song, ChengWei; Zhang, JunJie; Sun, Tao

    2015-03-01

    In the present work we elucidate the thermodynamic mechanisms of femtosecond (fs) laser ablation of amorphous polystyrene by means of molecular dynamics (MD) simulations. The effects of extrinsic parameter of laser pulse intensity and intrinsic parameter of molecular architecture on the laser ablation are further studied. Simulation results show that the laser ablation-induced polymeric material removal is achieved by evaporation from the surface and expansion within the bulk. Furthermore, inter-chain sliding and intra-chain change also play important roles in the microscopic deformation of the material. It is found that both the laser pulse intensity and the arrangement of phenyl groups have significant influence on the fs laser ablation of polystyrene.

  19. Modification of polyimide wetting properties by laser ablated conical microstructures

    NASA Astrophysics Data System (ADS)

    Least, Brandon T.; Willis, David A.

    2013-05-01

    Laser texturing of Kapton® HN polyimide was performed by low-fluence ablation using a pulsed, frequency tripled (349 nm) Nd:YLF laser. The laser was scanned in two dimensions in order to generate texture over a large area. The laser overlap percentage and fluence were varied and the resulting texture was studied. The texture features were inspected by electron microscopy and energy dispersive X-Ray spectroscopy (EDS), while the static contact angle of de-ionized water was measured by a contact angle goniometer. Rounded bump features were formed at all fluences, which decreased in areal density with fluence and number of laser pulses. Conical microstructures or "cones" were also formed at most fluences. Cones were larger than the bumps and thus had lower areal density, which increased as a function of the number of laser pulses. The polyimide was hydrophilic before texturing, with a contact angle of approximately 76°. For most of the experimental conditions the contact angle increased as a result of texturing, with the contact angle exceeding 90° for some textured surfaces, and reaching values as high as 118°. In general, the surfaces with significant increases in contact angle had high density of texture features, either bumps or cones. The surfaces that experienced a decrease in contact angle generally had low density of texture features. The increase in contact angle from a wetting (θ < 90°) to a nonwetting surface (θ > 90°) cannot be explained by texturing alone. EDS measurements indicate that textured regions had higher carbon content than the untextured regions due to depletion of oxygen species. The increase in carbon content relative to the oxygen content increased the native contact angle of the surface, causing the transition from hydrophilic to hydrophobic behavior. The contact angle of a textured surface increased as the relative spacing of features (diameter to spacing) decreased.

  20. Outcome of Endovenous Laser Ablation of Varicose Veins

    PubMed Central

    Rustempasic, Nedzad; Cvorak, Alemko; Agincic, Alija

    2014-01-01

    ABSTRACT Introduction: In Bosnia and Herzegovina according to available data, treatment of incompetent superficial lower extremity varicose veins by endovenous laser ablation (EVLA) has been introduced two years ago and so far no paper has been published regarding results of EVLA treatment of patients from our country. We wanted to present our results with EVLA treatment. Aim of study: to evaluate and compare primary posttreatment outcomes of endovenous laser ablation (EVLA) with classical surgical method of varicose vein treatment. Patients and methods: The study was clinical and prospective. It was carried out at Clinic for vascular surgery in Sarajevo where fifty-eight (58) patients received surgical treatment for varicose veins and in Aesthetic Surgery Center “Nasa mala klinika” in Sarajevo were sixty-one (61) patients with varicose veins were treated by endovenous laser ablation. Total 119 patients (limbs) with pathologic reflux only in great saphenous vein were evaluated between 1st of January 2013 and 31st of April 2014. Following primary outcome endpoints were evaluated smean day of return to normal everyday activities, patient subjective quantification of pain during first seven days after intervention, incidence of deep venous thrombosis (DVT), incidence of wound bleeding requiring surgical intervention, incidence of peri-saphenous vein hematoma and infection rate. Results: Mean of return to normal activities (expressed in days after intervention); EVLA vs. stripping (surgery) =1.21vs12.24, T test 13,619; p=0, 000, p<0,05. T test was used for comparing Mean value of visual pain analog scale for the first 7 days between groups, for all seven days pain was significantly higher in surgical group of patients as compared to EVLA group; p<0,05. Incidence of hematoma greater than 1% of total body surface area was significantly higher in patients receiving surgical treatment; Pearson Chi Square=23,830, p<0,05; odds ratio:10,453. Incidences of infection, deep

  1. Simulation of Laser Interaction with Ablative Plasma and ydrodynamic of Laser Supported Plasma(LSP)

    NASA Astrophysics Data System (ADS)

    Huifeng, Tong; Zhiping, Tang

    2011-06-01

    A general Godunov finite difference schemes-WENO(Weighted Essentially Non-Oscillatory) Schemes which have fifth-order accuracy was used to make a numerical calculation for 2-dimensional axis symmetrical laser-supported plasma flow field under laser ablated solid target. The models of the calculation of ionization degree of plasma and the interaction between laser beam and plasma and the simplified eos(equation of state) of plasma were considered in the simulation. The plasma field parameters during and after laser duration variation with time are also obtained. The simulation results show that the laser beam power was strong absorbed by plasma of target surface, and the velocity of LSD(Laser Supported Detonation) wave is half of ideal LSD value which derived from C-J detonation theory.

  2. Influence of water layer thickness on hard tissue ablation with pulsed CO2 laser

    NASA Astrophysics Data System (ADS)

    Zhang, Xianzeng; Zhan, Zhenlin; Liu, Haishan; Zhao, Haibin; Xie, Shusen; Ye, Qing

    2012-03-01

    The theory of hard tissue ablation reported for IR lasers is based on a process of thermomechanical interaction, which is explained by the absorption of the radiation in the water component of the tissue. The microexplosion of the water is the cause of tissue fragments being blasted from hard tissue. The aim of this study is to evaluate the influence of the interdependence of water layer thickness and incident radiant exposure on ablation performance. A total of 282 specimens of bovine shank bone were irradiated with a pulse CO2 laser. Irradiation was carried out in groups: without a water layer and with a static water layer of thickness ranging from 0.2 to 1.2 mm. Each group was subdivided into five subgroups for different radiant exposures ranging from 18 to 84 J/cm2, respectively. The incision geometry, surface morphology, and microstructure of the cut walls as well as thermal injury were examined as a function of the water layer thickness at different radiant exposures. Our results demonstrate that the additional water layer is actually a mediator of laser-tissue interaction. There exists a critical thickness of water layer for a given radiant exposure, at which the additional water layer plays multiple roles, not only acting as a cleaner to produce a clean cut but also as a coolant to prevent bone heating and reduce thermal injury, but also helping to improve the regularity of the cut shape, smooth the cut surface, and enhance ablation rate and efficiency. The results suggest that desired ablation results depend on optimal selection of both water layer thickness and radiant exposure.

  3. Influence of water layer thickness on hard tissue ablation with pulsed CO2 laser.

    PubMed

    Zhang, Xianzeng; Zhan, Zhenlin; Liu, Haishan; Zhao, Haibin; Xie, Shusen; Ye, Qing

    2012-03-01

    The theory of hard tissue ablation reported for IR lasers is based on a process of thermomechanical interaction, which is explained by the absorption of the radiation in the water component of the tissue. The microexplosion of the water is the cause of tissue fragments being blasted from hard tissue. The aim of this study is to evaluate the influence of the interdependence of water layer thickness and incident radiant exposure on ablation performance. A total of 282 specimens of bovine shank bone were irradiated with a pulse CO(2) laser. Irradiation was carried out in groups: without a water layer and with a static water layer of thickness ranging from 0.2 to 1.2 mm. Each group was subdivided into five subgroups for different radiant exposures ranging from 18 to 84 J/cm(2), respectively. The incision geometry, surface morphology, and microstructure of the cut walls as well as thermal injury were examined as a function of the water layer thickness at different radiant exposures. Our results demonstrate that the additional water layer is actually a mediator of laser-tissue interaction. There exists a critical thickness of water layer for a given radiant exposure, at which the additional water layer plays multiple roles, not only acting as a cleaner to produce a clean cut but also as a coolant to prevent bone heating and reduce thermal injury, but also helping to improve the regularity of the cut shape, smooth the cut surface, and enhance ablation rate and efficiency. The results suggest that desired ablation results depend on optimal selection of both water layer thickness and radiant exposure.

  4. An advanced optical system for laser ablation propulsion in space

    NASA Astrophysics Data System (ADS)

    Bergstue, Grant; Fork, Richard; Reardon, Patrick

    2014-03-01

    We propose a novel space-based ablation driven propulsion engine concept utilizing transmitted energy in the form of a series of ultra-short optical pulses. Key differences are generating the pulses at the transmitting spacecraft and the safe delivery of that energy to the receiving spacecraft for propulsion. By expanding the beam diameter during transmission in space, the energy can propagate at relatively low intensity and then be refocused and redistributed to create an array of ablation sites at the receiver. The ablation array strategy allows greater control over flight dynamics and eases thermal management. Research efforts for this transmission and reception of ultra-short optical pulses include: (1) optical system design; (2) electrical system requirements; (3) thermal management; (4) structured energy transmission safety. Research has also been focused on developing an optical switch concept for the multiplexing of the ultra-short pulses. This optical switch strategy implements multiple reflectors polished into a rotating momentum wheel device to combine the pulses from different laser sources. The optical system design must minimize the thermal load on any one optical element. Initial specifications and modeling for the optical system are being produced using geometrical ray-tracing software to give a better understanding of the optical requirements. In regards to safety, we have advanced the retro-reflective beam locking strategy to include look-ahead capabilities for long propagation distances. Additional applications and missions utilizing multiplexed pulse transmission are also presented. Because the research is in early development, it provides an opportunity for new and valuable advances in the area of transmitted energy for propulsion as well as encourages joint international efforts. Researchers from different countries can cooperate in order to find constructive and safe uses of ordered pulse transmission for propulsion in future space

  5. Laser Ablative Deposition of Polymer Films: A Promise for Sensor Fabrication

    NASA Astrophysics Data System (ADS)

    Blazevska-Gilev, Jadranka; Kupčík, Jaroslav; Šubrt, Jan; Pola, Josef

    There is a continuing interest in the use of polymer films as insulating components of sensors; a number of such films have been prepared by polymer sputtering or vacuum deposition processes involving gas phase pyrolysis/photolysis and by plasma decomposition of monomers. An attractive and rather new technique for the deposition of novel polymer films is IR laser ablation of polymers containing polar groups. We have recently studied this process with poly(vinyl chloride) (PVC), poly(vinyl acetate) (PVAc) and poly(vinyl chloride-co-vinyl acetate) P(VC/VAc) to establish its specific features and differences to conventional pyrolysis.

  6. Ablation and carbon deposition induced by UV laser irradiation of polyimide: Application to the metallization of VIAs in high density printed circuit boards

    NASA Astrophysics Data System (ADS)

    Metayer, P.; Davenas, J.; Bureau, J. M.

    2001-12-01

    Polyimides are known to exhibit large ablation rates upon irradiation with excimer laser due to their high absorbance in the UV and low fluorescence yield. We have studied different regimes of laser ablation according to the fluence and studied the structures resulting from carbon products deposition. For fluences larger than the polyimide ablation threshold, but lower than the carbon one, the development of one structure is the dominant process, whereas large ablation rates lead to polyimide etching above the carbon ablation threshold. The deposition of a carbon layer on the walls of ablated slits has in particular been investigated using an original experimental technique. Optical microscopy and MEB have shown that this carbon layer covered the main height of the ablated holes whereas a threshold (bare polyimide) for carbon condensation was evidenced at the bottom of the ablated hole. Raman spectroscopy and conductivity measurements have shown that the carbon phase is mainly graphitic. A dependence of the carbon condensation threshold on the slit width has been evidenced and discussed in relation with the angle of ejection of ablation debris. A procedure has been developed to render the bare polyimide of the threshold region conductive. At last the conductive properties of the walls of the ablated holes have been exploited to perform an electrolytic metallization. Implications for the production of interconnection vertical interconnections (VIAs) in high density printed circuits are addressed.

  7. INTERACTION OF LASER RADIATION WITH MATTER. LASER PLASMA: Laser ablation plume dynamics in nanoparticle synthesis

    NASA Astrophysics Data System (ADS)

    Osipov, V. V.; Platonov, V. V.; Lisenkov, V. V.

    2009-06-01

    The dynamics of the plume ejected from the surface of solid targets (YSZ, Nd:YAG and graphite) by a CO2 laser pulse with a duration of ~500 μs (at the 0.03 level), energy of 1.0-1.3 J and peak power of 6-7 kW have been studied using high-speed photography of the plume luminescence and shadow. The targets were used to produce nanopowders by laser evaporation. About 200 μs after termination of the pulse, shadowgraph images of the plumes above the YSZ and Nd:YAG targets showed dark straight tracks produced by large particles. The formation of large (~10 μm) particles is tentatively attributed to cracking of the solidified melt at the bottom of the ablation crater. This is supported by the fact that no large particles are ejected from graphite, which sublimes without melting. Further support to this hypothesis is provided by numerical 3D modelling of melt cooling in craters produced by laser pulses of different shapes.

  8. Alternatives to excimer laser refractive surgery: UV and mid-infrared laser ablation of intraocular lenses and porcine cornea

    NASA Astrophysics Data System (ADS)

    Serafetinides, A. A.; Makropoulou, M.; Spyratou, E.; Bacharis, C.

    2007-03-01

    Despite the fact that the laser applications in human ophthalmology are well established, further research is still required, for better and predictable ablation dosimetry on both cornea tissue and intraocular lenses. Further studies for alternative laser sources to the well established excimer lasers, such as UV or mid-infrared solid state lasers, have been proposed for refractive surgery. The precise lens ablation requires the use of laser wavelengths possessing a small optical penetration depth in the cornea and in the synthetic lenses, in order to confine the laser energy deposition to a small volume. In order to eliminate some very well known problems concerning the reshaping of cornea and the modification of the optical properties of the intraocular lenses, ablation experiments of ex vivo porcine cornea, acrylic PMMA and hydrophilic lenses were conducted with an Er:YAG laser (2.94 μm) and the fifth harmonic of a Nd:YAG laser (213 nm). The morphology of cornea was recorded using a cornea topography system before and immediately after the ablation. Histology analysis of the specimens was obtained, in order to examine the microscopic appearance of the ablated craters and the existence of any thermal damage caused by the mid-infrared and UV laser irradiation. The macroscopic morphology of the intraocular lens craters was inspected with an optical transmission microscope. Measurements of the ablation rates of the lenses were performed and simulated by a mathematical model.

  9. Co:MgF2 laser ablation of tissue: effect of wavelength on ablation threshold and thermal damage.

    PubMed

    Schomacker, K T; Domankevitz, Y; Flotte, T J; Deutsch, T F

    1991-01-01

    The wavelength dependence of the ablation threshold of a variety of tissues has been studied by using a tunable pulsed Co:MgF2 laser to determine how closely it tracks the optical absorption length of water. The Co:MgF2 laser was tuned between 1.81 and 2.14 microns, a wavelength region in which the absorption length varies by a decade. For soft tissues the ablation threshold tracks the optical absorption length; for bone there is little wavelength dependence, consistent with the low water content of bone. Thermal damage vs. wavelength was also studied for cornea and bone. Thermal damage to cornea has a weak wavelength dependence, while that to bone shows little wavelength dependence. Framing-camera pictures of the ablation of both cornea and liver show explosive removal of material, but differ as to the nature of the explosion.

  10. Comparison of the Effectiveness of Ablative and Non-Ablative Fractional Laser Treatments for Early Stage Thyroidectomy Scars

    PubMed Central

    Jang, Jin-Uk; Kim, Soo-Young; Kim, Woo-Kyung; Park, Seung-Ha; Lee, Byung-Il; Kim, Deok-Woo

    2016-01-01

    Background Open thyroidectomy is conventionally performed at the anterior side of neck, which is a body part with a comparatively great degree of open exposure; due to this, postoperative scarring may cause distress in patients. We aimed to compare the effects of ablative and nonablative fractional laser treatments on thyroidectomy scars. We examined medical records in a retrospective manner and analyzed scars based on their digital images by using the modified Manchester Scar Scale (mMSS). Methods Between February 2012 and May 2013, 55 patients with thyroidectomy scars were treated with ablative (34 patients) or nonablative (21 patients) fractional laser. Each patient underwent 4 laser treatment sessions in 3–4 week intervals, 1–2 months postoperatively. Scar improvement was assessed using patient images and the mMSS scale. Results The mean decrease in scar score was 3.91 and 3.47 in the ablative and nonablative groups, respectively; the reduction between 2 groups did not exhibit any significant difference (P=0.16). We used the scale once again to individually evaluate scar attributes. The nonablative group accounted for a considerably higher color score value (P=0.03); the ablative group accounted for a considerably higher contour score value (P<0.01). Patient satisfaction was high and no complications occurred. Conclusions Both types of fractional laser treatments can be used successfully for thyroidectomy scar treatment with minimal complications; however, results indicate that higher effectiveness may be obtained from the use of ablative and nonablative lasers for hypertrophic scars and early erythematous scars, respectively. Therefore, the appropriate laser for scar treatment should be selected according to its specific characteristics. PMID:27896191

  11. Time-Resolved Force and Schlieren Visualization Study of TEA CO2 Laser Ablation of Water Droplets

    NASA Astrophysics Data System (ADS)

    Li, Xiuqian; Hong, Yanji; Wen, Ming; Ye, Jifei; Cui, Cunyan

    2011-11-01

    Time-resolved force sensing technique was applied to the study of propulsive characteristics of water droplets for multi-pulse TEA (transversely excited at atmospheric pressure) CO2 laser propulsion. Laser-driven blast waves and associated flow dynamics in the impulse generation processes of ablation of water droplets were studied by Schlieren visualization. Experimental results showed that coupling coefficient and specific impulse decreased as the interval between laser pulses and pulse numbers was increased. The maximum speed of the blast wave in the opposite and same direction of laser propagation was respectively 10 km/s and 7 km/s.

  12. Ultrafast laser ablation in liquids for nanomaterials and applications.

    PubMed

    Rao, S Venugopal; Podagatlapalli, G Krishna; Hamad, Syed

    2014-02-01

    We present an inclusive overview of the ultrafast ablation technique performed in liquids. Being a comparatively new method, we bring out the recent progress achieved, present the challenges ahead, and outline the future prospects for this technique. The review is conveniently divided into five parts: (a) a succinct preamble to the technique of ultrafast ablation in liquids (ULAL) is provided. A brief introduction to the conventional ns ablation is also presented for the sake of completeness (b) fundamental physical processes involved in this technique are elaborated (c) specific advantages of the technique compared to other physical and chemical methodologies are enumerated (d) applications of this technique in photonics; biomedical and explosives detection [using surface-enhanced Raman scattering (SERS)] is updated (e) future prospects describing the potential of this technique for creating unique nanoparticles (NPs) and nanostructures (NSs) for niche applications. We also discuss some of the recently reported significant results achieved in a variety of materials, especially metals, using this technique. Furthermore, we present some of our own experimental data obtained from ULAL of Ag, Cu, and Zn in a variety of liquids such as acetone, water, acetonitrile etc. The generated NPs (colloidal solutions) and NSs (on substrates) have been successfully utilized for nonlinear optical, SERS, and biomedical applications.

  13. Molecular dynamics investigation of desorption and ion separation following picosecond infrared laser (PIRL) ablation of an ionic aqueous protein solution.

    PubMed

    Zou, J; Wu, C; Robertson, W D; Zhigilei, L V; Miller, R J D

    2016-11-28

    Molecular dynamics simulations were performed to characterize the ablation process induced by a picosecond infrared laser (PIRL) operating in the regime of desorption by impulsive vibrational excitation (DIVE) of a model peptide (lysozyme)/counter-ion system in aqueous solution. The simulations were performed for ablation under typical experimental conditions found within a time-of-flight mass spectrometer (TOF-MS), that is in vacuum with an applied electric field (E = ± 10(7) V/m), for up to 2 ns post-ablation and compared to the standard PIRL-DIVE ablation condition (E = 0 V/m). Further, a simulation of ablation under an extreme field condition (E = 10(10) V/m) was performed for comparison to extend the effective dynamic range of the effect of the field on charge separation. The results show that the plume dynamics were retained under a typical TOF-MS condition within the first 1 ns of ablation. Efficient desorption was observed with more than 90% of water molecules interacting with lysozyme stripped off within 1 ns post-ablation. The processes of ablation and desolvation of analytes were shown to be independent of the applied electric field and thus decoupled from the ion separation process. Unlike under the extreme field conditions, the electric field inside a typical TOF-MS was shown to modify the ions' motion over a longer time and in a soft manner with no enhancement to fragmentation observed as compared to the standard PIRL-DIVE. The study indicates that the PIRL-DIVE ablation mechanism could be used as a new, intrinsically versatile, and highly sensitive ion source for quantitative mass spectrometry.

  14. Molecular dynamics investigation of desorption and ion separation following picosecond infrared laser (PIRL) ablation of an ionic aqueous protein solution

    NASA Astrophysics Data System (ADS)

    Zou, J.; Wu, C.; Robertson, W. D.; Zhigilei, L. V.; Miller, R. J. D.

    2016-11-01

    Molecular dynamics simulations were performed to characterize the ablation process induced by a picosecond infrared laser (PIRL) operating in the regime of desorption by impulsive vibrational excitation (DIVE) of a model peptide (lysozyme)/counter-ion system in aqueous solution. The simulations were performed for ablation under typical experimental conditions found within a time-of-flight mass spectrometer (TOF-MS), that is in vacuum with an applied electric field (E = ± 107 V/m), for up to 2 ns post-ablation and compared to the standard PIRL-DIVE ablation condition (E = 0 V/m). Further, a simulation of ablation under an extreme field condition (E = 1010 V/m) was performed for comparison to extend the effective dynamic range of the effect of the field on charge separation. The results show that the plume dynamics were retained under a typical TOF-MS condition within the first 1 ns of ablation. Efficient desorption was observed with more than 90% of water molecules interacting with lysozyme stripped off within 1 ns post-ablation. The processes of ablation and desolvation of analytes were shown to be independent of the applied electric field and thus decoupled from the ion separation process. Unlike under the extreme field conditions, the electric field inside a typical TOF-MS was shown to modify the ions' motion over a longer time and in a soft manner with no enhancement to fragmentation observed as compared to the standard PIRL-DIVE. The study indicates that the PIRL-DIVE ablation mechanism could be used as a new, intrinsically versatile, and highly sensitive ion source for quantitative mass spectrometry.

  15. Femtosecond laser ablation characteristics of nickel-based superalloy C263

    NASA Astrophysics Data System (ADS)

    Semaltianos, N. G.; Perrie, W.; French, P.; Sharp, M.; Dearden, G.; Logothetidis, S.; Watkins, K. G.

    2009-03-01

    Femtosecond laser (180 fs, 775 nm, 1 kHz) ablation characteristics of the nickel-based superalloy C263 are investigated. The single pulse ablation threshold is measured to be 0.26±0.03 J/cm2 and the incubation parameter ξ=0.72±0.03 by also measuring the dependence of ablation threshold on the number of laser pulses. The ablation rate exhibits two logarithmic dependencies on fluence corresponding to ablation determined by the optical penetration depth at fluences below ˜5 J/cm2 (for single pulse) and by the electron thermal diffusion length above that fluence. The central surface morphology of ablated craters (dimples) with laser fluence and number of laser pulses shows the development of several kinds of periodic structures (ripples) with different periodicities as well as the formation of resolidified material and holes at the centre of the ablated crater at high fluences. The debris produced during ablation consists of crystalline C263 oxidized nanoparticles with diameters of ˜2-20 nm (for F=9.6 J/cm2). The mechanisms involved in femtosecond laser microprocessing of the superalloy C263 as well as in the synthesis of C263 nanoparticles are elucidated and discussed in terms of the properties of the material.

  16. Laser Ablation of Gallium Arsenide in Different Solutions

    SciTech Connect

    Ganeev, R.A.; Kuroda, H.; Ryasnyanskii, A.I.

    2005-12-15

    The optical, structural, and nonlinear optical characteristics of GaAs nanoparticles obtained by laser ablation in different liquids were investigated. Thermally induced self-defocusing in GaAs solutions was observed using both a high pulse repetition rate and nanosecond pulses. In studying the nonlinear optical characteristics of GaAs solutions using picosecond and femtosecond pulses, two-photon absorption was observed. The nonlinear absorption coefficient of an aqueous GaAs solution measured by the Z-scan technique and the nonlinear susceptibility of GaAs nanoparticles were, respectively, 0.7 x 10{sup -9} cm W{sup -1} and 2 x 10{sup -9} esu at a wavelength of 795 nm.

  17. Laser material processing system

    DOEpatents

    Dantus, Marcos

    2015-04-28

    A laser material processing system and method are provided. A further aspect of the present invention employs a laser for micromachining. In another aspect of the present invention, the system uses a hollow waveguide. In another aspect of the present invention, a laser beam pulse is given broad bandwidth for workpiece modification.

  18. Fabrication of 250-nm-hole arrays in glass and fused silica by UV laser ablation

    NASA Astrophysics Data System (ADS)

    Karstens, R.; Gödecke, A.; Prießner, A.; Ihlemann, J.

    2016-09-01

    Parallel nanohole drilling in glass using an ArF excimer laser (193 nm) is demonstrated. For the first time, hole arrays with 500 nm pitch and individual holes with 250 nm diameter and more than 100 nm depth are fabricated by phase mask imaging using a Schwarzschild objective. Holes in soda lime glass are drilled by direct ablation; fused silica is processed by depositing a SiOx-film on SiO2, patterning the SiOx by ablation, and finally oxidizing the remaining SiOx to SiO2. Thermally induced ordered dewetting of noble metal films deposited on such templates may be used for the fabrication of plasmonic devices.

  19. Experimental study on double-pulse laser ablation of steel upon multiple parallel-polarized ultrashort-pulse irradiations

    NASA Astrophysics Data System (ADS)

    Schille, Joerg; Schneider, Lutz; Kraft, Sebastian; Hartwig, Lars; Loeschner, Udo

    2016-07-01

    In this paper, double-pulse laser processing is experimentally studied with the aim to explore the influence of ultrashort pulses with very short time intervals on ablation efficiency and quality. For this, sequences of 50 double pulses of varied energy and inter-pulse delay, as adjusted between 400 fs and 18 ns by splitting the laser beam into two optical paths of different length, were irradiated to technical-grade stainless steel. The depth and the volume of the craters produced were measured in order to evaluate the efficiency of the ablation process; the crater quality was analyzed by SEM micrographs. The results obtained were compared with craters produced with sequences of 50 single pulses and energies equal to the double pulse. It is demonstrated that double-pulse processing cannot exceed the ablation efficiency of single pulses of optimal fluence, but the ablation crater surface formed smoother if inter-pulse delay was in the range between 10 ns and 18 ns. In addition, the influence of pulse duration and energy distribution between the individual pulses of the double pulse on ablation was studied. For very short inter-pulse delay, no significant effect of energy variation within the double pulse on removal rate was found, indicating that the double pulse acts as a big single pulse of equal energy. Further, the higher removal efficiency was achieved when double-pulse processing using femtosecond pulses instead of picosecond pulses.

  20. Evaluation of corneal ablation by an optical parametric oscillator (OPO) at 2.94 μm and an Er:YAG laser and comparison to ablation by a 193-nm excimer laser

    NASA Astrophysics Data System (ADS)

    Telfair, William B.; Hoffman, Hanna J.; Nordquist, Robert E.; Eiferman, Richard A.

    1998-06-01

    Purpose: This study first evaluated the corneal ablation characteristics of (1) an Nd:YAG pumped OPO (Optical Parametric Oscillator) at 2.94 microns and (2) a short pulse Er:YAG laser. Secondly, it compared the histopathology and surface quality of these ablations with (3) a 193 nm excimer laser. Finally, the healing characteristics over 4 months of cat eyes treated with the OPO were evaluated. Methods: Custom designed Nd:YAG/OPO and Er:YAG lasers were integrated with a new scanning delivery system to perform PRK myopic correction procedures. After initial ablation studies to determine ablation thresholds and rates, human cadaver eyes and in-vivo cat eyes were treated with (1) a 6.0 mm Dia, 30 micron deep PTK ablation and (2) a 6.0 mm Dia, -5.0 Diopter PRK ablation. Cadaver eyes were also treated with a 5.0 mm Dia, -5.0 Diopter LASIK ablation. Finally, cats were treated with the OPO in a 4 month healing study. Results: Ablation thresholds below 100 mJ/cm2 and ablation rates comparable to the excimer were demonstrated for both infrared systems. Light Microscopy (LM) showed no thermal damage for low fluence treatments, but noticeable thermal damage at higher fluences. SEM and TEM revealed morphologically similar surfaces for low fluence OPO and excimer samples with a smooth base and no evidence of collagen shrinkage. The Er:YAG and higher fluence OPO treated samples revealed more damage along with visible collagen coagulation and shrinkage in some cases. Healing was remarkably unremarkable. All eyes had a mild healing response with no stromal haze and showed topographic flattening. LM demonstrated nothing except a moderate increase in keratocyte activity in the upper third of the stroma. TEM confirmed this along with irregular basement membranes. Conclusions: A non- thermal ablation process called photospallation is demonstrated for the first time using short pulse infrared lasers yielding damage zones comparable to the excimer and healing which is also comparable to

  1. Infra-red femtosecond laser ablation: Benefit for LA-ICP-MS elemental analysis?

    NASA Astrophysics Data System (ADS)

    Poitrasson, F.; d'Abzac, F.; Freydier, R.; Seydoux-Guillaume, A.; Chmeleff, J.; Chatel, B.

    2011-12-01

    Femtosecond (fs) laser ablation systems have now been used for about a decade for elemental analysis in chemical and geosciences laboratories. Published studies investigated the influence of various analytical parameters, such as laser pulsewidth, wavelength, energy or ablation duration, on the quality of the analytical data produced by fs Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry (LA-ICP-MS). It was rapidly found that under comparable analytical conditions, chemical fractionation effects that may occur during laser-induced particle production, transport and/or decomposition in the ICP-MS plasma torch become negligible in the fs laser ablation regime under 300 fs laser pulsewidth. Another major benefit of fs laser ablation is its restricted matrix-sensitive nature compared to ns laser ablation, thereby facilitating greatly LA-ICP-MS calibration for chemical analysis with a reference material having completely different optical and chemical properties compared to the sample to be analyzed (e.g., a standard glass to calibrate analyses of a phosphate mineral). This effect is particularly remarkable as it can be stated from both UV and IR fs laser ablation studies. Reproducible laser ablations of optical quality quartz can also be produced using such an IR laser. Precise, accurate and reproducible chemical analyses may be obtained using ns laser ablation systems. However, this is achieved under carefully controlled analytical conditions using state of the art ablation cells. Instead, it appears that fs laser ablation is making LA-ICP-MS analyses more reliable. More recently, analytical studies combined with high spatial resolution microscopic techniques allowed us to understand better the nature of fs laser-matter interaction through the direct examination of the laser-induced craters and of the particles produced. These investigations have shown the dominance of mechanical over thermal effects on the solids ablated using a fs laser. Whatever the

  2. The effect of polarization on ultrashort pulsed laser ablation of thin metal films

    NASA Astrophysics Data System (ADS)

    Venkatakrishnan, K.; Tan, B.; Stanley, P.; Sivakumar, N. R.

    2002-08-01

    Ultrashort pulse lasers have proven to have superior advantages over conventional continuous wave and long pulse lasers for ablation of thin metal films. Though several investigations have been carried out to understand the phenomena of ultrashort pulse laser machining, the effect of the beam polarization on ablation of thin metal films has been seldom investigated. In this article, we report our recent observations on how the shape of the machined feature and also the damage threshold of the material varies according to the polarization of the ultrashort pulse laser beam. Based on this we have explained how the polarization of the beam controls the laser cutting rate, kerf width, edge quality, and ablation depth of the ablated feature.

  3. [A comparative analysis of tonsillectomy and ablation of the palatine tonsils with CO2 laser].

    PubMed

    Zbyshko, Ia B

    2007-01-01

    Efficacy and toletance of two methods were compared: ablation of the palatine tonsils with CO2 laser and tonsillectomy. 270 case histories (118 after tonsillectomy and 152 after laser ablation of the palatine tonsils) have been analysed and 50 patients from each group have been examined. The comparison of the methods leads to conclusion that laser ablation of the palatine tonsils prevents intraoperative and postoperative complications; makes postoperative hemostatic therapy unnecessary; allows conduction of the operations in outpatient clinics or day hospitals; causes minimal pain in the postoperative period; shortens duration of disability.

  4. Study of visible and mid-infrared laser ablation mechanism of PMMA and intraocular lenses: experimental and theoretical results.

    PubMed

    Spyratou, E; Makropoulou, M; Serafetinides, A A

    2008-04-01

    Laser-polymer interactions have attracted extensive attention both for understanding the inherent basic ablation mechanism and for development of tissue simulators in several biomedical laser applications such as in human ophthalmology. Ablation experiments were performed on polymethylmethacrylate used as cornea tissue simulator and PMMA intraocular lenses. The polymer-ablation mechanism was examined with two different wavelengths and pulse durations. The experiments were conducted with Nd:YAG and Er:YAG solid-state lasers, and the ablation rates were simulated by a mathematical model in each case. Furthermore, to investigate the role of tissue hydration during laser ablation, we performed a set of experiments in which Er:YAG laser ablation of hydrophilic acrylic intraocular lenses, with different H(2)O and D(2)O concentrations, was studied. The hydrophilic acrylic lenses with the higher concentration of H(2)O gave the most satisfactory results regarding both the ablation efficiency and the quality of the ablated craters.

  5. Ablation of hard dental tissues with the Er:YAG laser

    NASA Astrophysics Data System (ADS)

    Vickers, Vicki A.; Jacques, Steven L.; Schwartz, Jon A.; Motamedi, Massoud; Rastegar, Sohi; Martin, J. W.

    1992-08-01

    The Er:YAG laser ablation of hard dental tissues and artificial dental stones was studied. The hole depth after ablation was measured as a function of pulse energy and pulse number. The dental gypsum products allowed systematic study of how pulse energy, pulse number, and water content affected ablation. The studies on human teeth compared teeth stored in saline vs teeth stored in formalin.

  6. Modelling of Indirect Laser-induced Thin-film Ablation of Epoxy for Local Exposing of Carbon Fibers

    NASA Astrophysics Data System (ADS)

    Emonts, Michael; Fischer, Kai; Schmitt, Stefan; Schares, Richard Ludwig

    Laser radiation is used as enabling technology for intrinsic joining of high-strength CFRP laminates and fiber-reinforced thermoplastic injection moulding compounds by exposure of surface-near carbon fibers. Short-pulsed NIR laser sources represent an acceptable compromise with respect to ablation performance, remote process capability by use of compact 3D scanner and the capability for closed-loop process control. However, using such a laser source means also minimizing heat-affected zones (HAZ). Based on literature research about laser ablation of thin metal films, heat flow at CFRP and thermo-mechanical behavior in FRP by pyrolysis, an analytical model was generated for thin-film ablation of cured epoxy resins at the surface of CFRP laminates by lift-off of resin chips. A comparison between simulation and experimental results confirms the capability of the model to predict the exposure area and the HAZ with deviations below 15%. Threshold fluences for the HAZ (>1 J/cm2) and the resin ablation (>3 J/cm2) have been confirmed.

  7. Enhanced mass removal due to phase explosion during high irradiance nanosecond laser ablation of silicon

    SciTech Connect

    Yoo, Jong Hyun

    2000-05-01

    The morphology of craters resulting from high irradiance laser ablation of silicon was measured using a white light interferometry microscope. The craters show a dramatic increase in their depth and volume at a certain irradiance, indicating a change in the primary mechanism for mass removal. Laser shadowgraph imaging was used to characterize and differentiate the mass ejection processes for laser irradiances above and below the threshold value. Time-resolved images show distinct features of the mass ejected at irradiances above the threshold value including the presence of micron-sized particulates; this begins at approximately 300 ~ 400 ns after the start of laser heating. The analysis of the phenomena was carried out by using two models: a thermal evaporation model and a phase explosion model. Estimation of the crater depth due to the thermally evaporated mass led to a large underestimation of the crater depth for irradiances above the threshold. Above the threshold irradiance, the possibility of phase explosion was analyzed. Two important results are the thickness of the superheated liquid layer that is close to the critical temperature and the time for vapor bubbles that are generated in the superheated liquid to achieve a critical size. After reaching the critical size, vapor bubbles can grow spontaneously resulting in a violent ejection of liquid droplets from the superheated volume. The effects of an induced transparency, i.e. of liquid silicon turning into an optically transparent liquid dielectric medium, are also introduced. The estimated time for a bubble to reach the critical size is in agreement with the delay time measured for the initiation of large mass ejection. Also, the thickness of the superheated liquid layer that is close to the critical temperature at the time of the beginning of the large mass ejection is representative of the crater depth at the threshold irradiance. These results suggest that phase explosion is a plausible thermal

  8. Infrared nanosecond laser-metal ablation in atmosphere: Initial plasma during laser pulse and further expansion

    SciTech Connect

    Wu, Jian; Wei, Wenfu; Li, Xingwen; Jia, Shenli; Qiu, Aici

    2013-04-22

    We have investigated the dynamics of the nanosecond laser ablated plasma within and after the laser pulse irradiation using fast photography. A 1064 nm, 15 ns laser beam was focused onto a target made from various materials with an energy density in the order of J/mm{sup 2} in atmosphere. The plasma dynamics during the nanosecond laser pulse were observed, which could be divided into three stages: fast expansion, division into the primary plasma and the front plasma, and stagnation. After the laser terminated, a critical moment when the primary plasma expansion transited from the shock model to the drag model was resolved, and this phenomenon could be understood in terms of interactions between the primary and the front plasmas.

  9. In Situ Chemical Composition Measurements of Planetary Surfaces with a Laser Ablation Mass Spectrometer

    NASA Astrophysics Data System (ADS)

    Brigitte Neuland, Maike; Riedo, Andreas; Meyer, Stefan; Mezger, Klaus; Tulej, Marek; Wurz, Peter

    2013-04-01

    The knowledge of the chemical composition of moons, comets, asteroids or other planetary bodies is of particular importance for the investigation of the origin and evolution of the Solar System. For cosmochemistry, the elemental and isotopic composition of the surface material is essential information to investigate origin, differentiation and evolution processes of the body and therefore the history of our Solar System [1]. We show that the use of laser-based mass spectrometers is essential in such research because of their high sensitivity in the ppm range and their capability for quantitative elemental and isotopic analysis. A miniaturised Laser Ablation Time-of-Flight Mass Spectrometer (LMS) was developed in our group to study the elemental composition of solid samples [2]. The instrument's small size and light weight make it suitable for an application on a space mission to determine the elemental composition of a planetary surface for example [3]. Meteorites offer the excellent possibility to study extraterrestrial material in the laboratory. To demonstrate the sensitivity and functionality of the LMS instrument, a sample of the Allende meteorite has been investigated with a high spatial resolution. The LMS measurements allowed investigations of the elemental abundances in the Allende meteorite and detailed studies of the mineralogy and volatility [4]. These approaches can be of considerable interest for in situ investigation of grains and inhomogeneous materials with high sensitivity on a planetary surface. [1] Wurz, P., Whitby, J., Managadze, G., 2009, Laser Mass Spectrometry in Planetary Science, AIP Conf. Proc. CP1144, 70-75. [2] Tulej, M., Riedo, A., Iakovleva, M., Wurz, P., 2012, Int. J. Spec., On Applicability of a Miniaturized Laser Ablation Time of Flight Mass Spectrometer for Trace Element Measurements, article ID 234949. [3] Riedo, A., Bieler, A., Neuland, M., Tulej, M., Wurz, P., 2012, Performance evaluation of a miniature laser ablation time

  10. Spectrum of laser light scattered by nanoparticles in an ablation-induced cavitation bubble

    NASA Astrophysics Data System (ADS)

    Takeuchi, Masato; Sasaki, Koichi

    2016-04-01

    The spectrum of the laser light scattered by nanoparticles in a cavitation bubble, which was induced by laser ablation of a titanium target in water, was measured using a triple-grating spectrograph. The scattered laser light observed at 100 \\upmu s after laser ablation had no wavelength-shifted component, suggesting that nanoparticles at this delay time were metallic. The wavelength-shifted component was observed in the spectrum at a delay time of 200 \\upmu s, suggesting the formation of oxidized nanoparticles. However, we observed no peaks in the spectrum of the scattered laser light in the present in situ laser-light scattering experiment. On the other hand, we observed clear peaks in the Raman spectrum of synthesized nanoparticles. The experimental results suggest slow crystallization of nanoparticles in liquid in liquid-phase laser ablation.

  11. CO{sub 2} Laser Ablation Area Scaling And Redeposition On Flat Polyoxymethylene Targets

    SciTech Connect

    Sinko, John E.; Scharring, Stefan; Eckel, Hans-Albert; Tsukiyama, Yosuke; Umehara, Noritsugu; Ichihashi, Katsuhiro; Ogita, Naoya; Sasoh, Akihiro; Roeser, Hans-Peter

    2010-10-08

    One of the remaining unknown subjects of laser propulsion involves whether special benefits or challenges exist for applying laser ablation propulsion to targets with particularly large or small spot areas. This subject is of high importance for a wide range of topics ranging from laser removal of space debris to micropropulsion for laser propulsion vehicles. Analysis is complex since different ablation phenomena are dominant between atmosphere and vacuum conditions. Progress has also been impeded by the difficulty of setting control parameters (particularly fluence) constant while the spot area is adjusted. It is also usually difficult for one group to address small- and large-area effects using a single high-power laser system. Recent collaborative experiments on laser ablation area scaling at several institutions, using 100-J class and 10-J class CO{sub 2} lasers, have advanced the understanding of laser propulsion area scaling. The spot area-dependence of laser propulsion parameters has been investigated over an area range covering approximately 0.05-50 cm{sup 2} at low fluence of about 0.6 J/cm{sup 2}. The experiments were conducted well below the threshold for plasma formation, and provide an estimate of the ablation threshold for CO{sub 2} laser ablation of POM.

  12. What controls the composition and the structure of nanomaterials generated by laser ablation in liquid solution?

    PubMed

    Amendola, Vincenzo; Meneghetti, Moreno

    2013-03-07

    Laser ablation synthesis in liquid solution (LASiS) is a "green" technique that gives access to the preparation of a library of nanomaterials. Bare noble metal spherical particles, multiphase core-shell oxides, metal-semiconductor heterostructures, layered organometallic compounds and other complex nanostructures can be obtained with the same experimental set up, just by varying a few synthetic parameters. How to govern such versatility is one of the current challenges of LASiS and requires a thorough understanding of the physical and chemical processes involved in the synthesis. In this perspective, the fundamental mechanisms of laser ablation in liquids are summarized, organized according to their temporal sequence and correlated with relevant examples taken from the library of nanomaterials disclosed by LASiS, in order to show how synthesis parameters influence the composition and the structure of products. The resulting framework suggests that, to date, much attention has been devoted to the physical aspects of laser-matter interaction and to the characterization of the final products of the synthesis. Conversely, the clarification of chemical processes active during LASiS deserves more research efforts and requires the synergy among multiple investigation techniques.

  13. Temporal evolution of liquid-assisted hard bio-tissue ablation with infrared pulsed lasers under a liquid environment

    NASA Astrophysics Data System (ADS)

    Chen, Faner; Li, Qiang; Hua, Mingxin; Zhan, Zhenlin; Xie, Shusen; Zhang, Xianzeng

    2016-10-01

    Liquid-assisted hard biotissue ablation with the pulsed lasers takes advantages in precision and compatibility than mechanical tools in traditional surgery. The objective of this study was to monitor the dynamic process of the cavitation bubble evolution induced by Ho:YAG laser under water and identify the opening time of channel formation between the fiber tip to the target tissue surface. A free-running Ho:YAG laser was used in the experiment. The wavelength was 2.1 μm with a pulse duration of 350 us and pulse energy varied from 500 mJ to 2000 mJ. The high-speed camera (PCO. dimax, Germany, PCO) applied to monitor the whole ablation process was setting at a frame rate of 52000 frames/s. The results showed that the cavitation bubble induced by laser energy experienced an oscillation process including occurrence, expansion, contraction and subsequent collapse. A channel connected the fiber tip and target tissue surface was formed during the dynamic process which allowed the following pulse energy transmitted through the channel with a relative low absorption and directly interacted with the target tissue. The beginning time of channel formation, as well as the duration of channel opening, as functions of incident laser energy were also presented. A micro-explosion was observed near the tissue surface during the bubble collapse, which may contribute to produce a clean cut, reduce the thermal injury and improve the morphology of ablation crater.

  14. Formation of periodic structures upon laser ablation of metal targets in liquids

    SciTech Connect

    Kazakevich, Pavel V; Simakin, Aleksandr V; Shafeev, Georgii A

    2005-09-30

    Experimental data on the formation of ordered microstructures produced upon ablation of metal targets in liquids irradiated by a copper vapour laser or a pulsed Nd:YAG laser are presented. The structures were obtained on brass, bronze, copper, and tungsten substrates immersed in distilled water or ethanol. As a result of multiple-pulse laser ablation by a scanning beam, ordered microcones with pointed vertexes are formed on the target surface. The structures are separated by deep narrow channels. The structure period was experimentally shown to increase linearly with diameter of the laser spot on the target surface. (interaction of laser radiation with matter)

  15. Higher Order Chemistry Models in the CFD Simulation of Laser-Ablated Carbon Plumes

    NASA Technical Reports Server (NTRS)

    Scott, C. D.; Greendyke, R. B.; Creel, J. R.; Payne, B. T.

    2005-01-01

    Production of single-walled carbon nanotubes (SWNT) has taken place for a number of years and by a variety of methods such-as laser ablation, chemical vapor deposition, and arc-jet ablation. Yet, little is actually understood about the exact chemical kinetics and processes that occur in SWNT formation. In recent time, NASA Johnson Space Center has devoted a considerable effort to the experimental evaluation of the laser ablation production process for SWNT originally developed at Rice University. To fully understand the nature of the laser ablation process it is necessary to understand the development of the carbon plume dynamics within the laser ablation oven. The present work is a continuation of previous studies into the efforts to model plume dynamics using computational fluid dynamics (CFD). The ultimate goal of the work is to improve understanding of the laser ablation process, and through that improved understanding, refine the laser ablation production of SWNT. Fig. 1 shows a basic schematic of the laser-ablation oven at NASA-JSC. Construction of the facility is simple in concept. Two concentric quartz tubes of 1.5 mm thickness form the inner and outer tubes with inside diameters of 2.2 and 5.08 cm respectively. At one end of the inner tube are located two 60 Hz pulsed lasers operating at 1064 nm and 532 nm wavelength with beam diameters of 5 mm aligned coaxially with the longitudinal axis of the inner quartz tube. For standard nanotube production runs, a 10 ns 532 nm pulse is followed 50 ns later by a 10 ns 1064 nm pulse. Each pulse is of 300 mJ energy. A target of carbon graphite with approximately 1% nickel and cobalt catalysts is located at the other end of the inner quartz tube. In the ordinary processing of SWNT, a base flow of 100 sccm of argon is maintained from the laser location and exits past the carbon target at a pressure of 66.7 kPa. These conditions yield a baseline mass flow through the chamber of 2.723x10(exp -6)kg/s of argon. The whole

  16. Plasma luminescence feedback control system for precise ultrashort pulse laser tissue ablation

    SciTech Connect

    Kim, B.M.; Feit, M.D.; Rubenchick, A.M.; Gold, D.M.; Darrown, C.B.; Da Silva, L.B.

    1998-01-01

    Plasma luminescence spectroscopy was used for precise ablation of bone tissue without damaging nearby soft tissue using ultrashort pulse laser (USPL). Strong contrast of the luminescence spectra between bone marrow and spinal cord provided the real time feedback control so that only bone tissue can be selectively ablated while preserving the spinal cord.

  17. Generation of multiple stress waves in silica glass in high fluence femtosecond laser ablation

    SciTech Connect

    Hu Haofeng; Wang Xiaolei; Zhai Hongchen; Zhang Nan; Wang Pan

    2010-08-09

    Shadowgraphs of dynamic processes outside and inside transparent target during the intense femtosecond laser ablation of silica glass are recorded. Two material ejections outside the target and two corresponding stress waves inside the target are observed at different energy fluences. In particular, a third stress wave can be observed at energy fluence as high as 40 J/cm{sup 2}. The first wave is a thermoelastic wave, while the second and the third may be generated subsequently by the mechanical expansions. In addition, the magnitudes of the three stress waves decrease sequentially based on our analysis.

  18. Experimental investigation on thermal ablation of carbon-fiber/epoxy composite irradiated by continuous wave laser

    NASA Astrophysics Data System (ADS)

    He, Minbo; Ma, Zhiliang; Chen, Linzhu; Lin, Xinwei; Zhou, Menglian

    2015-05-01

    The tests of carbon-fiber/epoxy composite laminates, subjected to a tangential gas-flow and 1070 nm continuous wave laser are carried out to acquire the ablation laws of samples on the conditions of different gas-flow. Simultaneously, considered the images from camera of large dynamic range, the damage laws of samples are also obtained for various laser power densities. Experimental results reveal that, without airflow on sample surface, the smoke caused by laser heating can be quickly on fire which causes a burn damage on the surface of samples so that the mass loss is most of all. However, the tangential airflow can remove away the smoke which has a weakening effect on the energy of incidence laser. So the ablation depth has an obvious increase in laser irradiation area. Unlike airflow, nitrogen flow can obviously restrain oxidation ablation on surface so that the ablation damage in laser irradiation area is relatively not severe. On the other hand, as laser power density increases, the mass loss of samples continues to rise but isn't proportional. And the ablation heat with the increase of power density shows a complex change. Below power density of 390 W/cm2, the mass loss mainly depends on the pyrolysis of epoxy while the ablation heat has a gradual decrease. Along with power density increasing but less than 1330 W/cm2 , the oxidation ablation of carbon fibers will be a leading factor and the ablation heat shows a little increase. Above power density of 1330 W/cm2 , the carbon fibers turn up the phenomenon of sublimation. What's more, airflow removed effects will be enhanced in high temperature. In this case, the ablation heat again has a trend of decrease.

  19. Sprayable low density ablator and application process

    NASA Technical Reports Server (NTRS)

    Sharpe, M. H.; Hill, W. E.; Simpson, W. G.; Carter, J. M.; Brown, E. L.; King, H. M.; Schuerer, P. H.; Webb, D. D. (Inventor)

    1978-01-01

    A sprayable, low density ablative composition is described consisting esentially of: (1) 100 parts by weight of a mixture of 25-65% by weight of phenolic microballoons, 0-20% by weight of glass microballoons, 4-10% by weight of glass fibers, 25-45% by weight of an epoxy-modified polyurethane resin, 2-4% by weight of a bentonite dispersing aid, and 1-2% by weight of an alcohol activator for the bentonite; (2) 1-10 parts by weight of an aromatic amine curing agent; and (3) 200-400 parts by weight of a solvent.

  20. A novel laser ablation plasma thruster with electromagnetic acceleration

    NASA Astrophysics Data System (ADS)

    Zhang, Yu; Zhang, Daixian; Wu, Jianjun; He, Zhen; Zhang, Hua

    2016-10-01

    A novel laser ablation plasma thruster accelerated by electromagnetic means was proposed and investigated. The discharge characteristics and thrust performance were tested with different charged energy, structural parameters and propellants. The thrust performance was proven to be improved by electromagnetic acceleration. In contrast with the pure laser propulsion mode, the thrust performance in electromagnetic acceleration modes was much better. The effects of electrodes distance and the off-axis distance between ceramic tube and cathode were tested, and it's found that there were optimal structural parameters for achieving optimal thrust performance. It's indicated that the impulse bit and specific impulse increased with increasing charged energy. In our experiments, the thrust performance of the thruster was optimal in large charged energy modes. With the charged energy 25 J and the use of metal aluminum, a maximal impulse bit of 600 μNs, a specific impulse of approximate 8000 s and thrust efficiency of about 90% were obtained. For the PTFE propellant, a maximal impulse bit of about 350 μNs, a specific impulse of about 2400 s, and thrust efficiency of about 16% were obtained. Besides, the metal aluminum was proven to be the better propellant than PTFE for the thruster.

  1. Density Profile of a Foil Accelerated by Laser Ablation

    NASA Astrophysics Data System (ADS)

    Knauer, J. P.; Hu, S. X.; Goncharov, V. N.; Haberberger, D.

    2016-10-01

    An experiment to measure the density profile of a foil accelerated by laser ablation has been designed and is underway. High-density material is measured with x-ray radiography and low-density plasma is measured using 251-nm interferometry. Two-dimensional hydrodynamic simulation results from the code DRACO will be compared to these data. The accelerated foil is an 80- μm-thick CH target with Ge and Si-doped layers. The incident laser is a 351-nm, 5-ns pulse with a total energy of 6.2 kJ. Si and Ti x rays are used for the radiography measurement. A 1-D image versus time data are recorded with an x-ray streak camera and 2-D image data at specific times are recorded with an x-ray framing camera using point-projection backlighting. Foil acceleration is measured with the 1-D data. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

  2. A spectroscopic study of laser ablation plasma from Mo target

    NASA Astrophysics Data System (ADS)

    Jakubowska, Katarzyna; Kubkowska, Monika; Blagoev, Alexander; Rosiński, Marcin; Parys, Piotr; Gąsior, Paweł

    2014-05-01

    The goal of this contribution is to present time-resolved optical spectroscopy studies of laser ablation of the Mo target with ˜ 3.5 ns, 0.4 J pulses delivered by the Nd-YAG laser system at 1.06 μm. The sample was placed in a vacuum chamber under 5 × 10-5 mbar pressure and irradiated, with power densities varied up to 22.7 GW cm-2. The ion emission from the plasma plume was measured using an electrostatic ion energy analyzer (IEA) and ion collector, which allowed us to estimate the ion kinetic energy and charge independent of the applied power densities. The signal collected by the IEA indicated the presence of molybdenum ions up to eight-ion charge. Simultaneously after the ion emission, the optical spectra acquired within 2 μs of exposure time were observed in the wavelength range from 200 to 1000 nm with a Mechelle 5000 spectrometer equipped with an iCCD (iStar) detector. The plasma electron temperature was estimated from a Boltzmann plot based on the registered spectra as well as from the ion measurements.

  3. Excimer laser ablation for spatially controlled protein patterns

    NASA Astrophysics Data System (ADS)

    Thissen, Helmut; Hayes, Jason P.; Kingshott, Peter; Johnson, Graham; Harvey, Erol C.; Griesser, Hans J.

    2001-11-01

    Two-dimensional control over the location of proteins on surfaces is desired for a number of applications including diagnostic tests and tissue engineered medical devices. Many of these applications require patterns of specific proteins that allow subsequent two-dimensionally controlled cell attachment. The ideal technique would allow the deposition of specific protein patterns in areas where cell attachment is required, with complete prevention of unspecific protein adsorption in areas where cells are not supposed to attach. In our study, collagen I was used as an example for an extracellular matrix protein known to support the attachment of bovine corneal epithelial cells. An allylamine plasma polymer was deposited on a silicon wafer substrate, followed by grafting of poly(ethylene oxide). Two-dimensional control over the surface chemistry was achieved using a 248 nm excimer laser. Results obtained by XPS and AFM show that the combination of extremely low-fouling surfaces with excimer laser ablation can be used effectively for the production of spatially controlled protein patterns with a resolution of less than 1 micrometers . Furthermore, it was shown that bovine corneal epithelial cell attachment followed exactly the created protein patterns. The presented method is an effective tool for a number of in vitro and in vivo applications.

  4. KrF laser-induced ablation and patterning of Y--Ba--Cu--O films

    SciTech Connect

    Heitz, J.; Wang, X.Z.; Schwab, P.; Baeuerle, D. ); Schultz, L. )

    1990-09-01

    The ablation and patterning of Y--Ba--Cu--O films on (100) SrTiO{sub 3} and (100) MgO substrates by KrF excimer-laser light projection was investigated. Three different regimes of laser-material interactions were observed. Transition temperatures and critical current densities in laser-fabricated strip lines were investigated.

  5. Assessment of Tablet Surface Hardness by Laser Ablation and Its Correlation With the Erosion Tendency of Core Tablets.

    PubMed

    Narang, Ajit S; Breckenridge, Lydia; Guo, Hang; Wang, Jennifer; Wolf, Abraham Avi; Desai, Divyakant; Varia, Sailesh; Badawy, Sherif

    2017-01-01

    Surface erosion of uncoated tablets results in processing problems such as dusting and defects during coating and is governed by the strength of particle bonding on tablet surface. In this study, the correlation between dusting tendency of tablets in a coating pan with friability and laser ablation surface hardness was assessed using tablets containing different concentrations of magnesium stearate and tartaric acid. Surface erosion propensity of different batches was evaluated by assessing their dusting tendency in the coating pan. In addition, all tablets were analyzed for crushing strength, friability, modified friability test using baffles in the friability apparatus, and weight loss after laser ablation. Tablets with similar crushing strength showed differences in their surface erosion and dusting tendency when rotated in a coating pan. These differences did not correlate well with tablet crushing strength or friability but did show reasonably good correlation with mass loss after laser ablation. These results suggest that tablet surface mass loss by laser ablation can be used as a minipiloting (small-scale) tool to assess tablet surface properties during early stages of drug product development to assess the risk of potential large-scale manufacturing issues.

  6. A Simple Method for Improving the Spatial Resolution in Infrared Laser Ablation Mass Spectrometry Imaging

    NASA Astrophysics Data System (ADS)

    Hieta, Juha-Pekka; Vaikkinen, Anu; Auno, Samuli; Räikkönen, Heikki; Haapala, Markus; Scotti, Gianmario; Kopra, Jaakko; Piepponen, Petteri; Kauppila, Tiina J.

    2017-01-01

    In mass spectrometry imaging of tissues, the size of structures that can be distinguished is determined by the spatial resolution of the imaging technique. Here, the spatial resolution of IR laser ablation is markedly improved by increasing the distance between the laser and the focusing lens. As the distance between the laser and the lens is increased from 1 to 18 m, the ablation spot size decreases from 440 to 44 μm. This way, only the collimated center of the divergent laser beam is directed on the focusing lens, which results in better focusing of the beam. Part of the laser energy is lost at longer distance, but this is compensated by focusing of the radiation to a smaller area on the sample surface. The long distance can also be achieved by a set of mirrors, between which the radiation travels before it is directed to the focusing lens and the sample. This method for improving the spatial resolution can be utilized in mass spectrometry imaging of tissues by techniques that utilize IR laser ablation, such as laser ablation electrospray ionization, laser ablation atmospheric pressure photoionization, and matrix-assisted laser desorption electrospray ionization.

  7. Synthesis of silicon-based nanoparticles by 10.6 μm nanosecond CO2 laser ablation in liquid

    NASA Astrophysics Data System (ADS)

    Popovic, D. M.; Chai, J. S.; Zekic, A. A.; Trtica, M.; Momcilovic, M.; Maletic, S.

    2013-02-01

    Silicon-based nanoparticles were produced by irradiating a single-crystal silicon target with 10.6 μm nanosecond transverse excited atmospheric (TEA) pulsed CO2 laser in de-ionized water. The effects of the laser pulse energies and repetition rate were studied. To reveal the role of thermal effects, a low laser repetition rate has been applied, excluding the interaction of the laser beam with the previously generated cavitation bubble. The analysis of the influence of the laser pulse energies and the laser repetition rate showed that the increase of the laser pulse energies leads to an increase of the nanoparticle size. An explanation of such results was proposed and the importance of the role of the target surface temperature in the ablation process is discussed.

  8. Portable laser ablation sampling device for elemental fingerprinting of objects outside the laboratory with laser ablation inductively coupled plasma mass spectrometry.

    PubMed

    Glaus, Reto; Koch, Joachim; Günther, Detlef

    2012-06-19

    Laser ablation-inductively coupled plasma mass spectrometry (LA-ICPMS) is a powerful method for elemental fingerprinting of solid samples in a quasi-nondestructive manner. In order to extend the field of application to objects outside the laboratory, a portable laser ablation sampling device was assembled using a diode pumped solid state laser and fiber-optics. The ablated materials were sampled on membrane filters and subsequently quantified by means of LA-ICPMS. The analytical performance of this approach was investigated for glass and gold reference materials. Accuracies of better than 20% were reached for most elements and typical limits of detection were found to be in the range of 0.01-1 μg/g. In summary, this approach combines spatially resolved sampling with the detection power of ICPMS and enables elemental fingerprinting of objects which cannot be transferred to the laboratory, e.g., archeological artifacts in museums.

  9. Endoluminal non-contact soft tissue ablation using fiber-based Er:YAG laser delivery

    NASA Astrophysics Data System (ADS)

    Kundrat, Dennis; Fuchs, Alexander; Schoob, Andreas; Kahrs, Lüder A.; Ortmaier, Tobias

    2016-03-01

    The introduction of Er:YAG lasers for soft and hard tissue ablation has proven promising results over the last decades due to strong absorption at 2.94 μm wavelength by water molecules. An extension to endoluminal applications demands laser delivery without mirror arms due to dimensional constraints. Therefore, fiber-based solutions are advanced to provide exible access while keeping space requirements to a minimum. Conventional fiber-based treatments aim at laser-tissue interactions in contact mode. However, this procedure is associated with disadvantages such as advancing decrease in power delivery due to particle coverage of the fiber tip, tissue carbonization, and obstructed observation of the ablation progress. The objective of this work is to overcome aforementioned limitations with a customized fiber-based module for non-contact robot-assisted endoluminal surgery and its associated experimental evaluation. Up to the authors knowledge, this approach has not been presented in the context of laser surgery at 2.94 μm wavelength. The preliminary system design is composed of a 3D Er:YAG laser processing unit enabling automatic laser to fiber coupling, a GeO2 solid core fiber, and a customized module combining collimation and focusing unit (focal length of 20 mm, outer diameter of 8 mm). The performance is evaluated with studies on tissue substitutes (agar-agar) as well as porcine samples that are analysed by optical coherence tomography measurements. Cuts (depths up to 3mm) with minimal carbonization have been achieved under adequate moistening and sample movement (1.5mms-1). Furthermore, an early cadaver study is presented. Future work aims at module miniaturization and integration into an endoluminal robot for scanning and focus adaptation.

  10. Laser-launched flyer plate and confined laser ablation for shock wave loading: Validation and applications

    NASA Astrophysics Data System (ADS)

    Paisley, Dennis L.; Luo, Sheng-Nian; Greenfield, Scott R.; Koskelo, Aaron C.

    2008-02-01

    We present validation and some applications of two laser-driven shock wave loading techniques: laser-launched flyer plate and confined laser ablation. We characterize the flyer plate during flight and the dynamically loaded target with temporally and spatially resolved diagnostics. With transient imaging displacement interferometry, we demonstrate that the planarity (bow and tilt) of the loading induced by a spatially shaped laser pulse is within 2-7mrad (with an average of 4±1mrad), similar to that in conventional techniques including gas gun loading. Plasma heating of target is negligible, in particular, when a plasma shield is adopted. For flyer plate loading, supported shock waves can be achieved. Temporal shaping of the drive pulse in confined laser ablation allows for flexible loading, e.g., quasi-isentropic, Taylor-wave, and off-Hugoniot loading. These techniques can be utilized to investigate such dynamic responses of materials as Hugoniot elastic limit, plasticity, spall, shock roughness, equation of state, phase transition, and metallurgical characteristics of shock-recovered samples.

  11. CO2 TEA Laser-Enhanced Laser Ablation Molecular Isotopic Spectrometry (TELLAMIS)

    NASA Astrophysics Data System (ADS)

    Brown, Staci R.; Akpovo, Charlemagne A.; Ford, Alan; Herbert, Kenley; Johnson, Lewis

    2014-03-01

    Recently, it has been shown that the relative abundance of isotopes in enriched materials can be determined via laser-induced breakdown spectroscopy (LIBS) in a technique known as laser-ablation molecular isotopic spectroscopy (LAMIS). The original LAMIS work has focused on single-pulse (SP) LIBS for the excitation. However, dual-pulse (DP) LIBS reduces shot-to-shot variation and can lower detection limits of an element by about an order of magnitude or more. It also has the potential to improve the accuracy of the determination of the relative abundances of isotopes in LAMIS by minimizing the signal-to-noise ratio. In this work, a DP-LIBS technique for improving LAMIS relative-abundance information from a sample is presented. The new technique, called (TEA) Transverse-Excited breakdown in Atmosphere Laser-Enhanced Laser Ablation Molecular Isotopic Spectrometry (TELLAMIS), uses a carbon dioxide (CO2) laser to increase the breakdown emission from LIBS in the LAMIS method. This technique is demonstrated on a collection of relative abundance isotopes of boron- 10 and boron-11 in varying concentrations in boric acid. Least-squares fitting to theoretical models are used to deduce plasma parameters and understand reproducibility of results. DTRA.

  12. Analysis of the change in peak corneal temperature during excimer laser ablation in porcine eyes

    NASA Astrophysics Data System (ADS)

    Mosquera, Samuel Arba; Verma, Shwetabh

    2015-07-01

    The objective is to characterize the impact of different ablation parameters on the thermal load during corneal refractive surgery by means of excimer laser ablation on porcine eyes. One hundred eleven ablations were performed in 105 porcine eyes. Each ablation was recorded using infrared thermography and analyzed mainly based on the two tested local frequencies (40 Hz, clinical local frequency; 1000 Hz, no local frequency). The change in peak corneal temperature was analyzed with respect to varying ablation parameters [local frequency, system repetition rate, pulse energy, optical zone (OZ) size, and refractive correction]. Transepithelial ablations were also compared to intrastromal ablations. The average of the baseline temperature across all eyes was 20.5°C±1.1 (17.7°C to 22.2°C). Average of the change in peak corneal temperature for all clinical local frequency ablations was 5.8°C±0.8 (p=3.3E-53 to baseline), whereas the average was 9.0°C±1.5 for all no local frequency ablations (p=1.8E-35 to baseline, 1.6E-16 to clinical local frequency ablations). A logarithmic relationship was observed between the changes in peak corneal temperature with increasing local frequency. For clinical local frequency, change in peak corneal temperature was comparatively flat (r2=0.68 with a range of 1.5°C) with increasing system repetition rate and increased linearly with increasing OZ size (r2=0.95 with a range of 2.4°C). Local frequency controls help maintain safe corneal temperature increase during excimer laser ablations. Transepithelial ablations induce higher thermal load compared to intrastromal ablations, indicating a need for stronger thermal controls in transepithelial refractive procedures.

  13. Analysis of the change in peak corneal temperature during excimer laser ablation in porcine eyes.

    PubMed

    Arba Mosquera, Samuel; Verma, Shwetabh

    2015-07-01

    The objective is to characterize the impact of different ablation parameters on the thermal load during corneal refractive surgery by means of excimer laser ablation on porcine eyes. One hundred eleven ablations were performed in 105 porcine eyes. Each ablation was recorded using infrared thermography and analyzed mainly based on the two tested local frequencies (40 Hz, clinical local frequency; 1000 Hz, no local frequency). The change in peak corneal temperature was analyzed with respect to varying ablation parameters [local frequency, system repetition rate, pulse energy, optical zone (OZ) size, and refractive correction]. Transepithelial ablations were also compared to intrastromal ablations. The average of the baseline temperature across all eyes was 20.5°C±1.1 (17.7°C to 22.2°C). Average of the change in peak corneal temperature for all clinical local frequency ablations was 5.8°C±0.8 (p=3.3E-53 to baseline), whereas the average was 9.0°C±1.5 for all no local frequency ablations (p=1.8E-35 to baseline, 1.6E-16 to clinical local frequency ablations). A logarithmic relationship was observed between the changes in peak corneal temperature with increasing local frequency. For clinical local frequency, change in peak corneal temperature was comparatively flat (r 2 =0.68 with a range of 1.5°C) with increasing system repetition rate and increased linearly with increasing OZ size (r 2 =0.95 with a range of 2.4°C). Local frequency controls help maintain safe corneal temperature increase during excimer laser ablations. Transepithelial ablations induce higher thermal load compared to intrastromal ablations, indicating a need for stronger thermal controls in transepithelial refractive procedures.

  14. Experimental verification of the ablation pressure dependence upon the laser intensity at pulsed irradiation of metals

    NASA Astrophysics Data System (ADS)

    Krasyuk, I. K.; Semenov, A. Yu; Stuchebryukhov, I. A.; Khishchenko, K. V.

    2016-11-01

    Experiments for verification of a functional dependence of the ablation pressure on the irradiated surface of a target upon the laser intensity in a range from 1.2 to 350 TW/cm2 have been carried out. For that, at some intensities of the laser irradiation, time intervals between the laser pulse maximum and the moment of the shock-wave front arrival to the rear surface of the target were measured, which are dependent on the ablation pressure. Two schemes of the measurements were used. At the first scheme, at higher laser intensities, the front arrival moment is determined via an electron-optical camera when the rear surface begins glowing. At the second scheme, the front arrival moment is recorded when a probe laser pulse changes the character of the reflection by the rear surface of the irradiated target. Results of measurements are in agreement with the ablation pressure dependence upon the laser pulse intensity within 20%.

  15. Visualization of liquid-assisted hard tissue ablation with a pulsed CO2 laser

    NASA Astrophysics Data System (ADS)

    Li, X. W.; Chen, C. G.; Zhang, X. Z.; Zhan, Z. L.; Xie, S. S.

    2015-01-01

    To investigate the characteristics of liquid-mediated hard tissue ablation induced by a pulsed CO2 laser with a wavelength of 10.6 μm, a high speed camera was used to monitor the interaction between water, tissue and laser irradiation. The results showed that laser irradiation can directly impact on tissue through a vapor channel formed by the leading part of the laser pulse. The ablation debris plays a key role in liquid-assisted laser ablation, having the ability to keep the vapor channel open to extend actuation time. The runoff effect induced by vortex convection liquid flow can remove the tissue that obstructs the effect of the next laser pulse.

  16. The TriBeam system: Femtosecond laser ablation in situ SEM

    SciTech Connect

    Echlin, McLean P.; Straw, Marcus; Randolph, Steven; Filevich, Jorge; Pollock, Tresa M.

    2015-02-15

    Femtosecond laser ablation offers the unique ability to remove material at rates that are orders of magnitude faster than existing ion beam technologies with little or no associated damage. By combining ultrafast lasers with state-of-the-art electron microscopy equipment, we have developed a TriBeam system capable of targeted, in-situ tomography providing chemical, structural, and topographical information in three dimensions of near mm{sup 3} sized volumes. The origins, development, physics, current uses, and future potential for the TriBeam system are described in this tutorial review. - Graphical abstract: Display Omitted - Highlights: • An emerging tool, the TriBeam, for in situ femtosecond (fs) laser ablation is presented. • Fs laser ablation aided tomography at the mm{sup 3}-scale is demonstrated. • Fs laser induced deposition of Pt is demonstrated at sub-diffraction limit resolution. • Fs laser surface structuring is reviewed as well as micromachining applications.

  17. Guiding heat in laser ablation of metals on ultrafast timescales: an adaptive modeling approach on aluminum

    NASA Astrophysics Data System (ADS)

    Colombier, J. P.; Combis, P.; Audouard, E.; Stoian, R.

    2012-01-01

    Using an optimal control hydrodynamic modeling approach and irradiation adaptive time-design, we indicate excitation channels maximizing heat load in laser ablated aluminum at low energy costs. The primary relaxation paths leading to an emerging plasma are particularly affected. With impulsive pulses on ps pedestals, thermodynamic trajectories are preferentially guided in ionized domains where variations in ionization degree occur. This impinges on the gas-transformation mechanisms and triggers a positive bremsstrahlung absorption feedback. The highest temperatures are thus obtained in the expanding ionized matter after a final impulsive excitation, as the electronic energy relaxes recombinatively. The drive relies on transitions to weakly coupled front plasmas at the critical optical density, favoring energy confinement with low mechanical work. Alternatively, robust collisional heating occurs in denser regions above the critical point. This impacts the nature, the excitation degree and the energy content of the ablated matter. Adaptive modeling can therefore provide optimal strategies with information on physical variables not readily accessible and, as experimentally confirmed, databases for pulse shapes with interest in remote spectroscopy, laser-induced matter transfer, laser material processing and development of secondary sources.

  18. Laser ablation production of Ba, Ca, Dy, Er, La, Lu, and Yb ions

    NASA Astrophysics Data System (ADS)

    Olmschenk, S.; Becker, P.

    2017-04-01

    We use a pulsed nitrogen laser to produce atomic ions by laser ablation, measuring the relative ion yield for several elements, including some that have only recently been proposed for use in cold trapped ion experiments. For barium, we monitor the ion yield as a function of the number of applied ablation pulses for different substrates. We also investigate the ion production as a function of the pulse energy, and the efficiency of loading an ion trap as a function of radiofrequency voltage.

  19. Formation of x-ray Newton's rings from nano-scale spallation shells of metals in laser ablation

    NASA Astrophysics Data System (ADS)

    Nishikino, Masaharu; Hasegawa, Noboru; Tomita, Takuro; Minami, Yasuo; Eyama, Takashi; Kakimoto, Naoya; Izutsu, Rui; Baba, Motoyoshi; Kawachi, Tetsuya; Suemoto, Tohru

    2017-01-01

    The initial stages of the femtosecond (fs) laser ablation process of gold, platinum, and tungsten were observed by single-shot soft x-ray imaging technique. The formation and evolution of soft x-ray Newton's rings (NRs) were found for the first time. The soft x-ray NRs are caused by the interference between the bulk ablated surface and nanometer-scale thin spallation layer; they originate from the metal surface at pump energy fluence of around 1 J/cm2 and work as a flying soft x-ray beam splitter.

  20. Evaluation of the cavity margins after Er:YAG laser ablation of the enamel and dentin

    NASA Astrophysics Data System (ADS)

    Dostalova, Tatjana; Krejsa, Otakar; Jelinkova, Helena; Hamal, Karel

    1994-12-01

    This study investigates the checks of cavity margin after enamel and dentin ablation. The Er:YAG laser enamel and dentin ablation can be directly connected with the danger of cracks originating in the enamel near the cavity. This study evaluates the quality of the enamel edges after Er:YAG laser preparation. The enamel and dentin of buccal surfaces were ablated by the Er:YAG laser radiation. An Erbium:YAG laser system with the energy of 200 mJ was used to generate 200 microsecond(s) long pulses of mid-infrared 2.94 micrometers light in multimode configuration. The laser was operating in a free running mode, the repetition rate being 0.5 Hz with average laser power of 100 mW. Laser radiation was focused on the tooth tissue. Water cooling was used during the procedure in order to prevent tooth tissue destruction. The time of laser preparation was 5 minutes. A cavity of class V was prepared. The teeth were immersed into 0.5% basic fuchsin and then centrifuged at 6000 rev/min for 20 minutes. The microphotographs of the margins stained with 0.5% basic fuchsin were made and then the longitudinal section of the teeth were evaluated. The micrographs of the longitudinal section were checked and measured afterwards. The effect of the investigated laser irradiation on the origin of cracks was analyzed in the scanning electron microscope. Micrographs of each tooth before and after the laser ablation were compared. Micrographs of the intact teeth after extraction present the cracks of the enamel. They depend on the pressure exerted during extraction. The influence of the laser ablation proper is it bears no signs of new cracks. The conclusions of this study demonstrate the non-invasive nature of the Er:YAG laser ablation of the hard dental tissues.