Kinetics study of carbon raiser on the reduction of nickel laterite from Pomalaa, Southeast Sulawesi

NASA Astrophysics Data System (ADS)

Petrus, H. T. B. M.; Rhamdani, A. R.; Putera, A. D. P.; Warmada, I. W.; Yuliansyad, A. T.; Perdana, I.

2016-11-01

As one of the top ten on nickel laterite ore resources in the world, Indonesia must have been initiating the nickel processing in total amount of about 1.5 million tonnes. In regard to the low nickel laterite processing, one of the possible product is nickel pig iron (NPI) needed for the stainless steel industries. In this study carbon raiser that is waste from oil industries was used to replace metalurgical coke. The kinetic of nickel laterite reduction using carbon raiser was studied and compared with anthrasite coal. In this work, the author conducted the reduction of nickel laterite ores by both carbon raiser and anthrasite coal as reductant, in air and CO2 atmosphere, within the temperature ranged from 800°C and 1000°C. Two models were applied, sphere particle geometry model and Ginstling-Brounhstein diffusion model, to study the kinetic parameters. The results indicated that type of reductants and reduction atmosphere greatly influence the kinetic parameters. The obtained values of activation energy were varied between 17.44-18.12 kcal/mol.

The effect of smelting time and composition of palm kernel shell charcoal reductant toward extractive Pomalaa nickel laterite ore in mini electric arc furnace

NASA Astrophysics Data System (ADS)

Sihotang, Iqbal Huda; Supriyatna, Yayat Iman; Ismail, Ika; Sulistijono

2018-04-01

Indonesia is a country that is rich in natural resources. Being a third country which has a nickel laterite ore in the world after New Caledonia and Philippines. However, the processing of nickel laterite ore to increase its levels in Indonesia is still lacking. In the processing of nickel laterite ore into metal, it can be processed by pyrometallurgy method that typically use coal as a reductant. However, coal is a non-renewable energy and have high enough levels of pollution. One potentially replace is the biomass, that is a renewable energy. Palm kernel shell are biomass that can be used as a reductant because it has a fairly high fix carbon content. This research aims to make nickel laterite ores become metal using palm kernel shell charcoal as reductant in mini electric arc furnace. The result show that the best smelting time of this research is 60 minutes with the best composition of the reductant is 2,000 gram.

Nickel-cobalt laterites: a deposit model: Chapter H in Mineral deposit models for resource assessment

USGS Publications Warehouse

Marsh, Erin; Anderson, Eric J.; Gray, Floyd

2013-01-01

Nickel-cobalt (Ni-Co) laterite deposits are supergene enrichments of Ni±Co that form from intense chemical and mechanical weathering of ultramafic parent rocks. These regolith deposits typically form within 26 degrees of the equator, although there are a few exceptions. They form in active continental margins and stable cratonic settings. It takes as little as one million years for a laterite profile to develop. Three subtypes of Ni-Co laterite deposits are classified according to the dominant Ni-bearing mineralogy, which include hydrous magnesium (Mg)-silicate, smectite, and oxide. These minerals form in weathering horizons that begin with the unweathered protolith at the base, saprolite next, a smectite transition zone only in profiles where drainage is very poor, followed by limonite, and then capped with ferricrete at the top. The saprolite contains Ni-rich hydrous Mg-silicates, the Ni-rich clays occur in the transition horizon, and Ni-rich goethite occurs in the limonite. Although these subtypes of deposits are the more widely used terms for classification of Ni-Co laterite deposits, most deposits have economic concentrations of Ni in more than one horizon. Because of their complex mineralogy and heterogeneous concentrations, mining of these metallurgically complex deposits can be challenging. Deposits range in size from 2.5 to about 400 million tonnes, with Ni and Co grades of 0.66–2.4 percent (median 1.3) and 0.01–0.15 percent (median 0.08), respectively. Modern techniques of ore delineation and mineralogical identification are being developed to aid in streamlining the Ni-Co laterite mining process, and low-temperature and low-pressure ore processing techniques are being tested that will treat the entire weathered profile. There is evidence that the production of Ni and Co from laterites is more energy intensive than that of sulfide ores, reflecting the environmental impact of producing a Ni-Co laterite deposit. Tailings may include high levels of magnesium, sulfate, and manganese and have the potential to be physically unstable.

The contribution of lateritization processes to the formation of the kaolin deposits from eastern Amazon

NASA Astrophysics Data System (ADS)

da Costa, Marcondes Lima; Sousa, Daniel José Lima; Angélica, Rômulo Simões

The eastern region of the Amazon is home to the most important kaolin bauxite producing district in Brazil, referred to as the Paragominas-Capim kaolin bauxite district, which has a reserve of at least 1.0 billion tons of high-quality kaolin used in the paper coating industry. The kaolin deposits are closely related to sedimentary rocks of the Parnaíba basin and their lateritic cover. Two large deposits are already being mined: IRCC (Ipixuna) and PPSA (Paragominas). The geology of the IRCC mine is comprised of the kaolin-bearing lower unit (truncated mature laterite succession derived from the Ipixuna/Itapecuru formation) and the upper unit (immature lateritized Barreiras formation). The lower kaolin unit is characterized by a sandy facies at the bottom and a soft (ore) with flint facies at the top. It is formed by kaolinite, quartz, some iron oxi-hydroxides, mica and several accessories and heavy minerals. The <2 μm kaolinite crystallites only correspond to 41.3-58.3% of the soft kaolin, and large booklets of 15-300 μm are common. The degree of structure order of kaolinite decreases towards the flint kaolin. The chemical composition of the soft kaolin is similar to the theoretical chemical composition of kaolinite, with low iron content, and can be well correlated to most kaolin deposits in the region. The distribution pattern of chemical elements from sandy to flint kaolin (lower unit) suggests a lateritic evolution and erosive truncation. This is quite distinct from the upper unit, which has a mineralogical and chemical pathway relating it to a complete immature lateritic profile. The geological evolution of the IRCC kaolin is similar to that of other deposits in the eastern Amazon region, being comprised of: parent rocks formed in an estuarine marine and fluvio-laccustrine environment during the early Cretaceous; establishment of mature lateritization with the formation of kaolin in the Eocene; marine transgression and regression - (Pirabas and Barreiras formation) with kaolin profile erosion and forward movement of deferruginization and flintization during the Miocene after partial mangrove covering; and immature lateritization - partial kaolin ferruginization during the Pleistocene.

Growing Eremanthus erythropappus in crushed laterite: A promising alternative to topsoil for bauxite-mine revegetation.

PubMed

Machado, Naiara Amaral de Miranda; Leite, Mariangela Garcia Praça; Figueiredo, Maurílio Assis; Kozovits, Alessandra Rodrigues

2013-11-15

Topsoil is the preferred substrate for areas requiring rehabilitation after bauxite mining. However, topsoil is sometimes lacking and so there is a need to test the suitability of other, locally available substrates. In an abandoned bauxite mine in Southeastern Brazil, small patches of native vegetation spontaneously established in shallow depressions over weathered laterite, suggesting that granulometric reduction may have facilitated the establishment of plants. To test this hypothesis, blocks of laterite collected in the area were crushed to simulate texture observed in the vegetation patches. Topsoil collected in a preserved ferruginous field near to the extraction area was also used as a substrate in which Eremanthus erythropappus seedlings, a native woody species, were grown. Seedlings were cultivated without fertilizers in these two substrates and also directly over the exposed and uncrushed laterite. The species proved to be very promising for the revegetation, showing a high survival rate in all substrates. Higher annual growth rates and higher final biomass values were observed in topsoil, but the granulometric reduction of laterite doubled plant growth rate in comparison to the exposed laterite. This result was likely due to the increased availability of essential nutrients to plants and to the improvement in physical conditions for root growth and functioning. Moreover, seedling allometry was not altered by the type of substrate, suggesting that the species was highly tolerant to the new substrate conditions, a fundamental characteristic for success of revegetation of bauxite extraction degraded areas. Copyright © 2013 Elsevier Ltd. All rights reserved.

Satellite Remote Sensing For Aluminum And Nickel Laterites

NASA Astrophysics Data System (ADS)

Henderson, Frederick B.; Penfield, Glen T.; Grubbs, Donald K.

1984-08-01

The new LANDSAT-4,-5/Thematic Mapper (TM) land observational satellite remote sensing systems are providing dramatically new and important short wave infrared (SWIR) data, which combined with Landsat's Multi-Spectral Scanner (MSS) visible (VIS), very near infrared (VNIR), and thermal infrared (TI) data greatly improves regional geological mapping on a global scale. The TM will significantly improve clay, iron oxide, aluminum, and nickel laterite mapping capabilities over large areas of the world. It will also improve the ability to discriminate vegetation stress and species distribution associated with lateritic environments. Nickel laterites on Gag Island, Indonesia are defined by MSS imagery. Satellite imagery of the Cape Bougainville and the Darling Range, Australia bauxite deposits show the potential use of MSS data for exploration and mining applications. Examples of satellite syn-thetic aperture radar (SAR) for Jamaica document the use of this method for bauxite exploration. Thematic Mapper data will be combined with the French SPOT satellite's high spatial resolution and stereoscopic digital data, and U.S., Japanese, European, and Canadian Synthetic Aperture Radar (SAR) data to assist with logistics, mine development, and environ-mental concerns associated with aluminum and nickel lateritic deposits worldwide.

Characterization of nickel laterite reduction from Pomalaa, Sulawesi Tenggara

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rhamdani, Ahmad Rizky; Petrus, Himawan T. B. M., E-mail: bayu.petrus@ugm.ac.id; Fahrurrozi, Moh.

2015-12-29

The effect of using different reductors in the reduction process of nickel laterite was investigated. In this work, the author conducted the reduction of nickel laterite ores by anthracite coal, lamtoro charcoal, and carbon raiser, in air and CO{sub 2} atmosphere, within the temperature ranged from 800°C and 1000°C. The results indicate that at higher temperatures, the reduction reactions proceed more complete. According to the X-ray powder diffraction (XRD) analysis, the type of carbon used greatly influence the rate of the reduction of nickel laterite. The order of reactivity is anthracite coal, lamtoro charcoal, and carbon raiser, respectively. The reductionmore » atmospheric condition also greatly influences the reduction process. The reduction process in CO{sub 2} atmospheric condition gives a lot of significant decrease in hematite and magnetite presence, means that the reduction reactions proceed more complete compared to the reduction process in the air atmospheric condition.« less

Effects of fines content on hydraulic conductivity and morphology of laterite soil as hydraulic barrier

NASA Astrophysics Data System (ADS)

Bello Yamusa, Yamusa; Yunus, Nor Zurairahetty Mohd; Ahmad, Kamarudin; Rahman, Norhan Abd; Sa'ari, Radzuan

2018-03-01

Laterite soil was investigated to find out the effects of fines content and to identify the micro-structural and molecular characteristics to evaluate its potentiality as a compacted soil landfill liner material. Tests were carried out on natural soil and reconstituted soil by dry weight of soil samples to determine the physical and engineering properties of the soil. All tests were carried out on the samples by adopting the British Standard 1377:1990. The possible mechanisms that contributed to the clay mineralogy were analyzed using spectroscopic and microscopic techniques such as field emission scanning electron microscopy (FESEM), energy-dispersive X-ray (EDX) and X-ray diffractometry (XRD). The laterite soil was found to contain kaolinite as the major clay minerals. A minimum of 50% fines content of laterite soil met the required result for hydraulic barriers in waste containment facilities.

Thermodynamic Analysis of the Selective Reduction of a Nickeliferous Limonitic Laterite Ore by Hydrogen

NASA Astrophysics Data System (ADS)

Elliott, R.; Pickles, C. A.

2017-09-01

Nickeliferous limonitic laterite ores are becoming increasingly attractive as a source of metallic nickel as the costs associated with recovering nickel from the sulphide ores increase. Unlike the sulphide ores, however, the laterite ores are not amenable to concentration by conventional mineral processing techniques such as froth flotation. One potential concentrating method would be the pyrometallurgical solid state reduction of the nickeliferous limonitic ores at relatively low temperatures, followed by beneficiation via magnetic separation. A number of reductants can be utilized in the reduction step, and in this research, a thermodynamic model has been developed to investigate the reduction of a nickeliferous limonitic laterite by hydrogen. The nickel recovery to the ferronickel phase was predicted to be greater than 95 % at temperatures of 673-873 K. Reductant additions above the stoichiometric requirement resulted in high recoveries over a wider temperature range, but the nickel grade of the ferronickel decreased.

Geochemical indications and Detrital Zircon U-Pb ages of net-like laterite from Youjiang terrace, Bose Basin, southwestern China: new evidence of proximal provenance for laterite sediments

NASA Astrophysics Data System (ADS)

Cheng, F.; Hong, H.; Li, C.; Ye, H.; Yang, H.

2015-12-01

The net-like laterite sediments is widely spread over the terraces and high lands of the river valley in southern China during mid-Pleistocene, although whose origin is still debated. The Xiaomei laterite sediments on the terraces of Youjiang River, Guangxi Zhuang Autonomous Region, southern China, was dominated by the intermittently uplift of the Tibetan Plateau for the mechanism during the Quaternary times. Compared to the loess-paleosol deposits in Chinese Loess Plateau (CLP), the upper continental crust (UCC) and the post-Archean Australian average shale (PAAS), the sediments show notable depletion of the relative mobile compositions like CaO, MgO, Na2O, K2O, Sr, Ba and the accumulation of TiO2, Al2O3, Fe2O3(t), Zr, but similar with other laterite sediments (the Xuancheng and Jiujiang laterite profiles) in the middle to lower reaches of Yangtze River, southern China. The relatively uniform La/Th ratio, U/Pb vs. Th/Pb ratio and chondrite-normalized REE distribution pattern of Xiaomei samples are similar with the loess-paleosol deposits and UCC values, which suggesting the sediments have experienced well-mixing prior to deposition and intense superficial weathering. The low ɛNd(t) values and uniform 147Sm/144Nd ratios with the 87Sr/86Sr vs. Rb/Sr ratios show the notable differences with loess-paleosol deposits and the recycling function of the old fluvial sediments which are similar with the Pearl River sediments. The stable zircon age distribution pattern with three age groups of 240-300Ma, 420-480Ma and 900-1000Ma for Xiaomei laterite samples are different with the loess-paleosol deposits and its source regions. The zircons are mainly derived from a source of the Upper Permian to Middle Triassic clastic rocks in Youjiang Basin, superordinate tectonic unit of Bose Basin, and their potential source areas like the Emeishan Large Igneous Province (Emeishan LIP) and the southeastern area of south China Craton (SCC). For the basis of these data, we suggest that that the aeolian dusts may have not started to accumulate in southern China during these times, and the laterite sediments in southern China may dominate by the proximal supplementation.

Nickel and cobalt distribution in the laterites of the Lomié region, south-east Cameroon

NASA Astrophysics Data System (ADS)

Yongue-Fouateu, R.; Ghogomu, R. T.; Penaye, J.; Ekodeck, G. E.; Stendal, H.; Colin, F.

2006-05-01

In the Lomié region (south-east Cameroon), strong weathering of serpentinized ultramafic rocks has produced a thick laterite cover with significant nickel and cobalt contents. The highest concentrations of these elements are located in the middle section of the laterite profiles, in the lower clay horizon, and preferentially along the slopes of the interfluves. The investigation of the composition of the laterite ores (by whole-rock analysis) and of the main components, using SEM/microprobe and XRD, reveals the presence of four main enriched facies: a non-differentiated facies, a layered smectitic facies, a quartz-rich facies and a gibbsitic nodular facies. Nickel, with generally low concentrations (less than 2% NiO), is hosted by several secondary mineral phases (goethite, Mn-oxyhydroxides and smectite locally). Cobalt is generally of higher grade (up to 0.9% CoO), and is associated with cryptocrystalline and crystallized Mn-oxyhydroxides. SEM/microprobe observations suggest that nickel and cobalt concentration in secondary minerals is due to repeated remobilization. This has also favored the formation of mineral phases, of which the best crystallized and most richly mineralized are mainly those of the asbolan-lithiophorite group. The SEM studies indicate that these mineral phases show various morphologies related to their chemical composition: poorly crystallized nipple shaped (Fe, Mn, Ni), fine cross-bedded needles (Mn, Ni) and elongated crystals (Mn, Al, Ni, Co) occur in the layered smectitic facies, while platy and needle-like forms (Mn, Al, Ni, Co) characterize the gibbsitic nodular facies. The predominantly cobaltiferous nature of the Lomié laterite ore deposit is the result of remobilizations and transformations of elements that led to the impoverishment of both the Ni-Co contents of the laterite but most importantly of Ni rather than Co.

Vertical changes of the Co and Mn speciation along a lateritic regolith developed on peridotites (New Caledonia)

DOE PAGES

Dublet, Gabrielle; Juillot, Farid; Brest, Jessica; ...

2017-07-21

Because they can host significant amounts of Co, the Mn-oxides are commonly considered as the major Co-bearing mineral species in lateritic environments. However, little is known about the process leading to the formation and/or the weathering of these Co-rich Mn-oxides. This lack of knowledge is mainly due to the fact that Co concentrations are too low in primary silicates for classical speciation analysis. In this study, we investigated both Co and Mn speciation in a 64 m thick lateritic regolith developed upon peridotites in New Caledonia, by combining High Energy Resolution Fluorescence Detection X-ray absorption Near Edge Structure (HERFD-XANES) spectroscopymore » at the Co K-edge with classical XANES spectroscopy at the Mn K-edge, bulk chemistry (ICP) and mineralogy (XRD). The results obtained provide new insights into the evolution of Co and Mn speciation as a function of the weathering stages. Co and Mn primarily occur as Co(II) and Mn(II,III) in olivine and serpentine in the bedrock. During the first weathering stage, these forms of Co and Mn are progressively oxidized toward Co(III) and Mn(III,IV), which occur mainly as Co(III)-bearing Mn(III/IV)-oxides in the transition between the saprolite and the laterite. In the uppermost lateritic horizons, long-time weathering resulted in a strong leaching of Co and Mn, and the remaining of these elements occurs as Co(II) and Mn(III) substituting for Fe(III) in goethite. Finally, this latter scavenging process emphasizes the importance of Fe-oxides for the long-term stabilization of Co and Mn in such deeply weathered laterites.« less

Vertical changes of the Co and Mn speciation along a lateritic regolith developed on peridotites (New Caledonia)

NASA Astrophysics Data System (ADS)

Dublet, Gabrielle; Juillot, Farid; Brest, Jessica; Noël, Vincent; Fritsch, Emmanuel; Proux, Olivier; Olivi, Luca; Ploquin, Florian; Morin, Guillaume

2017-11-01

Because they can host significant amounts of Co, the Mn-oxides are commonly considered as the major Co-bearing mineral species in lateritic environments. However, little is known about the process leading to the formation and/or the weathering of these Co-rich Mn-oxides. This lack of knowledge is mainly due to the fact that Co concentrations are too low in primary silicates for classical speciation analysis. In this study, we investigated both Co and Mn speciation in a 64 m thick lateritic regolith developed upon peridotites in New Caledonia, by combining High Energy Resolution Fluorescence Detection X-ray absorption Near Edge Structure (HERFD-XANES) spectroscopy at the Co K-edge with classical XANES spectroscopy at the Mn K-edge, bulk chemistry (ICP) and mineralogy (XRD). The results obtained provide new insights into the evolution of Co and Mn speciation as a function of the weathering stages. Co and Mn primarily occur as Co(II) and Mn(II,III) in olivine and serpentine in the bedrock. During the first weathering stage, these forms of Co and Mn are progressively oxidized toward Co(III) and Mn(III,IV), which occur mainly as Co(III)-bearing Mn(III/IV)-oxides in the transition between the saprolite and the laterite. In the uppermost lateritic horizons, long-time weathering resulted in a strong leaching of Co and Mn, and the remaining of these elements occurs as Co(II) and Mn(III) substituting for Fe(III) in goethite. This latter scavenging process emphasizes the importance of Fe-oxides for the long-term stabilization of Co and Mn in such deeply weathered laterites.

Identification of Karstic Features in Lateritic Soil by an Integrated Geophysical Approach

NASA Astrophysics Data System (ADS)

Anbazhagan, P.; Rohit, Divyesh; Prabhakaran, Athul; Vidyaranya, B.

2018-06-01

Lateritic soils are widely spread across the southern and central parts of India. Lateritic formations usually have soft sediments, entrapped between hard to medium soft lateritic rock, which are leached due to the ingress of water during rainy seasons creating hollow sections or cavities which span over large lengths. Laterites are highly heterogeneous and prone to cavitation due to its weathering process; a sound knowledge of the subsurface condition is required before starting any construction. This study presents the application of integrated geophysical investigation for the identification of cavities at a mega construction site in Kerala State, India. Geophysical survey methods, namely ground penetrating radar (GPR) and multichannel analysis of surface waves (MASWs) techniques, are used to identify the heterogeneities in lateritic soils and localized cavities. The survey areas identified are critical sections of a mega construction project subjected to heavy dynamic and static loads. The preliminary GPR survey is carried out across the study areas at specific interval spacing to identify probable heterogeneities. Confirmative survey or detailed GPR and MASW surveys are carried out at the locations identified in the preliminary survey at close intervals to confirm the presence of an anomaly and identify its location. The anomalies in the GPR radargram are identified by visual inspection and trace amplitude approach. Using MASW survey, a 2D shear wave velocity profile is generated to identify low shear wave velocity zones which confirm the presence of an anomaly. On comparing the data from both GPR and MASW survey techniques, the underground cavities were successfully identified at multiple locations with further crosschecking with borings. The study further provided details on subsurface lithology at survey locations.

Supergene neoformation of Pt-Ir-Fe-Ni alloys: multistage grains explain nugget formation in Ni-laterites

NASA Astrophysics Data System (ADS)

Aiglsperger, Thomas; Proenza, Joaquín A.; Font-Bardia, Mercè; Baurier-Aymat, Sandra; Galí, Salvador; Lewis, John F.; Longo, Francisco

2017-10-01

Ni-laterites from the Dominican Republic host rare but extremely platinum-group element (PGE)-rich chromitites (up to 17.5 ppm) without economic significance. These chromitites occur either included in saprolite (beneath the Mg discontinuity) or as `floating chromitites' within limonite (above the Mg discontinuity). Both chromitite types have similar iridium-group PGE (IPGE)-enriched chondrite normalized patterns; however, chromitites included in limonite show a pronounced positive Pt anomaly. Investigation of heavy mineral concentrates, obtained via hydroseparation techniques, led to the discovery of multistage PGE grains: (i) Os-Ru-Fe-(Ir) grains of porous appearance are overgrown by (ii) Ni-Fe-Ir and Ir-Fe-Ni-(Pt) phases which are overgrown by (iii) Pt-Ir-Fe-Ni mineral phases. Whereas Ir-dominated overgrowths prevail in chromitites from the saprolite, Pt-dominated overgrowths are observed within floating chromitites. The following formation model for multistage PGE grains is discussed: (i) hypogene platinum-group minerals (PGM) (e.g. laurite) are transformed to secondary PGM by desulphurization during serpentinization; (ii) at the stages of serpentinization and/or at the early stages of lateritization, Ir is mobilized and recrystallizes on porous surfaces of secondary PGM (serving as a natural catalyst) and (iii) at the late stages of lateritization, biogenic mediated neoformation (and accumulation) of Pt-Ir-Fe-Ni nanoparticles occurs. The evidence presented in this work demonstrates that in situ growth of Pt-Ir-Fe-Ni alloy nuggets of isometric symmetry is possible within Ni-laterites from the Dominican Republic.

Nickel distribution and isotopic fractionation in a Brazilian lateritic regolith: Coupling Ni isotopes and Ni K-edge XANES

NASA Astrophysics Data System (ADS)

Ratié, G.; Garnier, J.; Calmels, D.; Vantelon, D.; Guimarães, E.; Monvoisin, G.; Nouet, J.; Ponzevera, E.; Quantin, C.

2018-06-01

Ultramafic (UM) rocks are known to be nickel (Ni) rich and to weather quickly, which makes them a good candidate to look at the Ni isotope systematics during weathering processes at the Earth's surface. The present study aims at identifying the Ni solid speciation and discussing the weathering processes that produce Ni isotope fractionation in two deep laterite profiles under tropical conditions (Barro Alto, Goiás State, Brazil). While phyllosilicates and to a lower extent goethite are the main Ni-bearing phases in the saprolitic part of the profile, iron (Fe) oxides dominate the Ni budget in the lateritic unit. Nickel isotopic composition (δ60Ni values) has been measured in each unit of the regolith, i.e., rock, saprock, saprolite and laterite (n = 52). δ60Ni varies widely within the two laterite profiles, from -0.10 ± 0.05‰ to 1.43 ± 0.05‰, showing that significant Ni isotope fractionation occurs during the weathering of UM rocks. Overall, our results show that during weathering, the solid phase is depleted in heavy Ni isotopes due to the preferential sorption and incorporation of light Ni isotopes into Fe oxides; the same mechanisms likely apply to the incorporation of Ni into phyllosilicates (type 2:1). However, an isotopically heavy Ni pool is observed in the solid phase at the bottom of the saprolitic unit. This feature can be explained by two hypotheses that are not mutually exclusive: (i) a depletion in light Ni isotopes during the first stage of weathering due to the preferential dissolution of light Ni-containing minerals, and (ii) the sorption or incorporation of isotopically heavy Ni carried by percolating waters (groundwater samples have δ60Ni of 2.20 and 2.27‰), that were enriched in heavy Ni isotopes due to successive weathering processes in the overlying soil and laterite units.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dublet, Gabrielle; Juillot, Farid; Brest, Jessica

Because they can host significant amounts of Co, the Mn-oxides are commonly considered as the major Co-bearing mineral species in lateritic environments. However, little is known about the process leading to the formation and/or the weathering of these Co-rich Mn-oxides. This lack of knowledge is mainly due to the fact that Co concentrations are too low in primary silicates for classical speciation analysis. In this study, we investigated both Co and Mn speciation in a 64 m thick lateritic regolith developed upon peridotites in New Caledonia, by combining High Energy Resolution Fluorescence Detection X-ray absorption Near Edge Structure (HERFD-XANES) spectroscopymore » at the Co K-edge with classical XANES spectroscopy at the Mn K-edge, bulk chemistry (ICP) and mineralogy (XRD). The results obtained provide new insights into the evolution of Co and Mn speciation as a function of the weathering stages. Co and Mn primarily occur as Co(II) and Mn(II,III) in olivine and serpentine in the bedrock. During the first weathering stage, these forms of Co and Mn are progressively oxidized toward Co(III) and Mn(III,IV), which occur mainly as Co(III)-bearing Mn(III/IV)-oxides in the transition between the saprolite and the laterite. In the uppermost lateritic horizons, long-time weathering resulted in a strong leaching of Co and Mn, and the remaining of these elements occurs as Co(II) and Mn(III) substituting for Fe(III) in goethite. Finally, this latter scavenging process emphasizes the importance of Fe-oxides for the long-term stabilization of Co and Mn in such deeply weathered laterites.« less

Extraction of nickel from Ramu laterite by sulphation roasting-water leaching

NASA Astrophysics Data System (ADS)

Wang, Weiwei; Du, Shangchao; Liu, Guo; Tang, Jianwen; Lu, Yeda; Lv, Dong

2017-08-01

Recovery of nickel from a PNG nickel laterite with high content of iron by a sulphation roasting-water leaching has been studied. The influences of sulfuric acid/ore ratio, temperature of roasting and water on recovery efficiency were investigated. The effective separation of nickel over the co-existed elements including iron was achieved by the process with mixing, curing, roasting and leaching stages. Near 100% of nickel was leached from the roasted laterite by water at 80°C in an atmospheric air, while co-leaching of about 2% of iron, under the optimal pre-treatment conditions with the ratio of acid: ore around 0.45:1 and the roasting temperature about 650°C. The advantages and disadvantages of sulphation atmospheric leaching are compared with pressure acid leaching with engineering consideration.

Lamtoro charcoal (l. leucocephala) as bioreductor in nickel laterite reduction: performance and kinetics study

NASA Astrophysics Data System (ADS)

Petrus, H. T. B. M.; Diga, A.; Rhamdani, A. R.; Warmada, I. W.; Yuliansyah, A. T.; Perdana, I.

2017-04-01

The performance and kinetic of nickel laterite reduction were studied. In this work, the reduction of nickel laterite ores by anthracite coal, representing the high-grade carbon content matter, and lamtoro charcoal, representing the bioreductor, were conducted in air and CO2 atmosphere, within the temperature ranged from 800°C and 1000°C. XRD analysis was applied to observe the performance of anthracite and lamtoro as a reductor. Two models were applied, sphere particle geometry model and Ginstling-Brounhstein diffusion model, to study the kinetic parameters. The results indicated that the type of reductant and the reduction atmosphere used greatly influence the kinetic parameters. The obtained values of activation energy vary in the range of 13.42-18.12 kcal/mol.

Co-reduction of Copper Smelting Slag and Nickel Laterite to Prepare Fe-Ni-Cu Alloy for Weathering Steel

NASA Astrophysics Data System (ADS)

Guo, Zhengqi; Pan, Jian; Zhu, Deqing; Zhang, Feng

2018-02-01

In this study, a new technique was proposed for the economical and environmentally friendly recovery of valuable metals from copper smelting slag while simultaneously upgrading nickel laterite through a co-reduction followed by wet magnetic separation process. Copper slag with a high FeO content can decrease the liquidus temperature of the SiO2-Al2O3-CaO-MgO system and facilitate formation of liquid phase in a co-reduction process with nickel laterite, which is beneficial for metallic particle growth. As a result, the recovery of Ni, Cu, and Fe was notably increased. A crude Fe-Ni-Cu alloy with 2.5% Ni, 1.1% Cu, and 87.9% Fe was produced, which can replace part of scrap steel, electrolytic copper, and nickel as the burden in the production of weathering steel by an electric arc furnace. The study further found that an appropriate proportion of copper slag and nickel laterite in the mixture is essential to enhance the reduction, acquire appropriate amounts of the liquid phase, and improve the growth of the metallic alloy grains. As a result, the liberation of alloy particles in the grinding process was effectively promoted and the metal recovery was increased significantly in the subsequent magnetic separation process.

Inorganic polymers from laterite using activation with phosphoric acid and alkaline sodium silicate solution: Mechanical and microstructural properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lassinantti Gualtieri, Magdalena, E-mail: magdalena.gualtieri@unimore.it; Romagnoli, Marcello; Pollastri, Simone

2015-01-15

Geopolymers from laterite, an iron-rich soil available in developing countries, have great potential as building materials. In this work, laterite from Togo (Africa) was used to prepare geopolymers using both phosphoric acid and alkaline sodium silicate solution. Microstructural properties were investigated by scanning electron microscopy, X-ray powder diffraction and mercury porosimetry, whereas thermal properties were evaluated by thermal analyses. The local environment of iron was studied by X-ray Absorption Spectroscopy (XANES region). The mechanical properties were determined. Modulus of Rupture and Young's modulus fell in the ranges 3.3–4.5 MPa and 12–33 GPa, respectively, rendering the materials good candidates for constructionmore » purposes. Heating above 900 °C results in weight-gain, presumably due to iron redox reactions. X-ray Absorption Spectroscopy data evidence changes in the chemical and structural environments of iron following thermal treatment of geopolymers. These changes indicate interaction between the geopolymer structure and iron during heating, possibly leading to redox properties. -- Highlights: •Geopolymerization of laterite is promising for fabrication of building materials. •Both phosphoric acid and alkaline sodium silicate solution can be used for activation. •Thermally activated redox properties of the inorganic polymers were observed.« less

Effects of reduction temperature to Ni and Fe content and the morphology of agglomerate of reduced laterite limonitic nickel ore by coal-bed method

NASA Astrophysics Data System (ADS)

Abdul, Fakhreza; Pintowantoro, Sungging; Kawigraha, Adji; Nursidiq, Ahlidin

2018-04-01

As the current drop of nickel sulfide ore on earth, the attention to nickel laterite ore processing was inscreased in order to fulfill the future nickel demand needs. This research aims to optimized the process of nickel laterite ore extraction using coal bed method. This research was conducted by reducing low grade nickel laterite ore (limonitic) with nickel content of 1.25 %. The reduction process was carried out using CO gas which formed by the reaction of coal and dolomite. The Briquette of nickel ore, coal, Na2SO4 mixtures incorporated in the crucible with bed, then reduced for 6 hours at the temperature of 1200 °C. 1400 °C, and 1400 °C. The result of the research shown that the highest increase of Ni content and Ni recovery value was in the reduction temperature of 1400 °C with the increase of 3.44 %, and the recovery value of Ni equal to 86.75 %. While the highest increase of Fe content and Fe recovery value, respectively, was in the reduction temperature of 1300 °C with the increase of 22.67 % and 1200 °C with Fe recovery value of 89.41 %.

Analysis of holding time variations to Ni and Fe content and morphology in nickel laterite limonitic reduction process by using coal-dolomite bed

NASA Astrophysics Data System (ADS)

Abdul, Fakhreza; Pintowantoro, Sungging; Yuwandono, Ridwan Bagus

2018-04-01

With the depletion of nickel sulfide ore resources, the nickel laterit processing become an attention to fulfill nickel world demans. Reducing laterite nickel by using a low cost carbonaceous reductan has proved produces high grade ferronickel alloy. In this research, reduction was carried out to low grade laterite nickel (limonite) with 1.25% nikel content by using CO gas reductant formed by reaction between coal and dolomite. Reduction process preceded by forming brickets mixture from limonit ore, coal, and Na2SO4, then the brickets placed inside crucible bed together with dolomit and reduced at temperature 1400 °C with holding time variations 4, 6, and 8 hours. EDX, XRD, and SEM test were carried out to find out the Ni and nickel grade after reduced, the phases that formed, and the morphology brickets after reduced. The reduction results shows that the highest increase on nickel grade was obtained by 8 hours holding time increasing 5.84 % from initial grade, and the highest recovery was obtained by 6 hours holding time with recovery 88.51 %. While the higest increase on Fe grade was obtained by 4 hours holding time, and the highest recovery Fe was obtained by 4 hours holding time with recovery 85.41%.

Effect of Lime Stabilization on Vertical Deformation of Laterite Halmahera Soil

NASA Astrophysics Data System (ADS)

Saing, Zubair; Djainal, Herry

2018-04-01

In this paper, the study was conducted to determine the lime effect on vertical deformation of road base physical model of laterite Halmahera soil. The samples of laterite soil were obtained from Halmahera Island, North Maluku Province, Indonesia. Soil characteristics were obtained from laboratory testing, according to American Standard for Testing and Materials (ASTM), consists of physical, mechanical, minerals, and chemical. The base layer of physical model testing with the dimension; 2m of length, 2m of width, and 1.5m of height. The addition of lime with variations of 3, 5, 7, an 10%, based on maximum dry density of standard Proctor test results and cured for 28 days. The model of lime treated laterite Halmahera soil with 0,1m thickness placed on subgrade layer with 1,5m thickness. Furthermore, the physical model was given static vertical loading. Some dial gauge is placed on the lime treated soil surface with distance interval 20cm, to read the vertical deformation that occurs during loading. The experimentals data was analyzed and validated with numerical analysis using finite element method. The results showed that the vertical deformation reduced significantly on 10% lime content (three times less than untreated soil), and qualify for maximum deflection (standard requirement L/240) on 7-10% lime content.

Dating Amazonian laterites through the novel geochronometers kaolinite and iron oxides

NASA Astrophysics Data System (ADS)

Allard, Thierry; Bressan Riffel, Silvana; Gautheron, Cécile; Fernandes Soares, Bruna; Pinna-Jamme, Rosella; Morin, Guillaume

2016-04-01

Soils on Earth's surface are in constant interaction with climate. As a matter of fact, soils cannot only produce greenhouse effect gases, such as NO2 and CH4, but also behave as sinks for CO2, especially by silicate weathering. Major processes of silicate weathering are known and exhibit climatic zonation at the global scale. Laterites are particularly relevant because they are ancient and deeply weathered soils of major significance. They occupy 30 % of the continental surface and can keep records of past climates and landscape modifications (paleosurface) through specific mineral markers. These formations reach several tens of meters and are mainly composed of kaolinite, iron and aluminium oxides as well as relicts of parent minerals such as quartz and ancillary minerals. Once the major processes of laterite formation are known, their age will allow a growth of researches, owing to the implementation of various chronometers. Moreover, it is fundamental to date laterites in order to improve our understanding of soil formation related to paleoclimates, and to build predictive models of their evolution. In this study, we focus on comparing kaolinite ages with the still unknown ages of lateritic duricrusts from the central Amazon region (Brazil), where strong weathering processes were developed from the early Tertiary, after the Andean uplift. The central Amazon region displays flat areas and dissected plateaus (100-180 m a.s.l.) sustained by weathered clastic sedimentary rocks and latosols. The region contains horizons of duricrusts, relatively continuous layers of Fe-cuirasses, stratified lateritic profiles, and kaolin deposits. Here we employed two methods to date ubiquitous secondary minerals of laterite, which are consistent with geological time-scale. The corresponding geochronometers are the following: (i) radiation-induced defects in kaolinite (trapped in duricrusts) analysed by electron paramagnetic resonance spectroscopy (EPR) (Balan et al., 2005), and (ii) (U-Th)/He on millimetric-sized pisolites of iron oxides. Goethite (U-Th)/He ages range from Late Pliocene to Pleistocene. Taking advantage of the crystallographic characterization of samples and the use of a new He production/diffusion code for iron oxides, we interpret that the results correspond to the ages of Fe oxides crystallization. In addition, these ages are younger than those assessed by kaolinite, which yielded Oligocene-Miocene ages for the weathered sediments of Alter do Chão Formation (Cretaceous-Paleogene unit) and Miocene-Pliocene ages for the topsoil. As a result of the Andean uplift and drainage reversal of the Amazon River, Miocene sediments were deposited in the western Amazon. Dated Fe-cuirasses suggest a minimum age of Early Pliocene for the Solimões formation A probability density plot of Goethite ages suggests an intensification and/or preservation of weathering processes during the Late Pliocene, revealing warm and humid conditions for that period. Both geochronometers are providing an opportunity to constrain the geodynamics and climatic history for the central Amazon region. Balan, E., Allard, T., Fritsch, E., Sélo, M., Falguères, C., Chabaux, F., Pierret, M.C. and Calas, G. (2005) Formation and evolution of lateritic profiles in the middle Amazon basin: insights from radiation-induced defects in kaolinite. Geochimi. Cosmochimi. Acta. 69, 2193-2204.

Effects of simulated acid rain on microbial characteristics in a lateritic red soil

Treesearch

Hua-qin Xu; Jia-en Zhang; Ying Ouyang; Ling Lin; Guo-ming Quan; Ben-liang Zhao; Jia-yu Yu

2015-01-01

A laboratory experiment was performed to examine the impact of simulated acid rain (SAR) on nutrient leaching, microbial biomass, and microbial activities in a lateritic red soil in South China. The soil column leaching experiment was conducted over a 60-day period with the following six SAR pH treatments (levels): 2.5, 3.0, 3.5, 4.0, 4.5, and 5.0 and one control...

Effects of corn cob ash on lime stabilized lateritic soil

NASA Astrophysics Data System (ADS)

Nnochiri, Emeka Segun

2018-03-01

This study assesses the effects of Corn Cob Ash (CCA) on lime-stabilized lateritic soil. Preliminary tests were carried out on the natural soil sample for purpose of identification and classification. Lime being the main stabilizing material was thoroughly mixed with the soil sample to determine the optimum lime requirement of the sample as a basis for evaluating the effects of the CCA. The optimum lime requirement was 10%. The CCA was thereafter added to the lime stabilized soil in varying proportions of 2, 4, 6, 8 and 10%. Unsoaked CBR increased from 83% at 0% CCA to highest value of 94% at 4% CCA. Unconfined Compressive Strength (UCS) values increased from 1123kN/m2 at 0% CCA to highest value of 1180kN/m2 at 4% CCA. It was therefore concluded that CCA can serve as a good complement for lime stabilization in lateritic soil.

The effect of tempering treatment on mechanical properties and microstructure for armored lateritic steel

NASA Astrophysics Data System (ADS)

Herbirowo, Satrio; Adjiantoro, Bintang; Romijarso, Toni Bambang; Pramono, Andika Widya

2018-05-01

High demand of armor material impacts on the use of lateritic steel as alternative armored material, therefore an increase of its mechanical properties is necessary. Quenching and tempering process can be used to increase the mechanical properties of the lateritic steel. The variables that used in this research are variation in media quench (water, oil, and air) and variation in tempering temperatures (0, 100, and 200 °C). The results show that specimen with water quenchant tempered at 100 °C have the highest average on hardness (59.1 HRC) and tensile strength. Specimen with oil quenchant tempered at 100 °C has the highest impact toughness (52 J). Secondary hardening and tempered martensite embrittlement phenomenon is found in some specimens where its hardness increased and its impact toughness decreased after the tempering process. Microstructures which formed in this process are martensite and retained austenite phase with fracture types are brittle.

Carbothermic Reduction of Nickeliferous Laterite Ores for Nickel Pig Iron Production in China: A Review

NASA Astrophysics Data System (ADS)

Rao, Mingjun; Li, Guanghui; Jiang, Tao; Luo, Jun; Zhang, Yuanbo; Fan, Xiaohui

2013-11-01

Both the consumption and production of crude stainless steel in China rank first in the world. In 2011, the nickel production in China amounted to 446 kilotons, with the proportion of electrolytic nickel and nickel pig iron (NPI) registering 41.5% and 56.5%, respectively. NPI is a low-cost feedstock for stainless steel production when used as a substitute for electrolytic nickel. The existing commercial NPI production processes such as blast furnace smelting, rotary kiln-electric furnace smelting, and Krupp-Renn (Nipon Yakin Oheyama) processes are discussed. As low-temperature (below 1300°C) reduction of nickeliferous laterite ores followed by magnetic separation could provide an alternative avenue without smelting at high temperature (~1500°C) for producing ferronickel with low cost, the fundamentals and recent developments of the low-temperature reduction of nickeliferous laterite ores are reviewed.

Ferronickel Preparation from Nickeliferous Laterite by Rotary Kiln-Electric Furnace Process

NASA Astrophysics Data System (ADS)

Li, Guanghui; Jia, Hao; Luo, Jun; Peng, Zhiwei; Zhang, Yuanbo; Jiang, Tao

Nickel is an important strategic metal, which is mainly used for stainless steel production. In the recent years, ferronickel has been used as a substitute for electrolytic nickel for alleviating the cost of stainless steel production. Rotary kiln-electric furnace (RKEF) smelting is currently the world-wide mainstreaming process for ferronickel production from nickeliferous laterite ore, in spite of the high power consumption. In this study, aiming to provide some meaningful guidance for ferronickel production of RKEF smelting, reductive roasting followed by smelting process was carried out. The conditions including reducing parameters (roasting temperature and time) and smelting parameters (coke dosage, CaO dosage, melting temperature and time) were ascertained. The metal recovery ratios, as well as Ni, Fe, S and P content of ferronickel were considered. The results showed that a ferronickel containing 10. 32 wt. % Ni was obtained from a laterite with 1. 85 wt. % Ni, the nickel recovery ratio was about 99%.

Potential for cobalt recovery from lateritic ores in Europe

NASA Astrophysics Data System (ADS)

Herrington, R.

2012-04-01

Cobalt is one of the 'critical metals' identified under the EU Raw Materials Initiative. Annually the global mine production of cobalt is around 55,000 tonnes,with Europe's industries consuming around 30% of that figure. Currently Europe produces around 27 tonnes of cobalt from mines in Finland although new capacity is planned. Co-bearing nickel laterite ores being mined in Greece, Macedonia and Kosovo where the cobalt is currently not being recovered (ores have typical analyses of 0.055% Co and >1% Ni,). These ores are currently treated directly in pyrometallurgical plants to recover the contained nickel and this process means there is no separate cobalt product produced. Hydrometallurgical treatment of mineralogically suitable laterite ores can recover the cobalt; for example Cuba recovers 3,500 tonnes of cobalt from its laterite mining operations, which are of a similar scale to the current European operations. Implementation of hydrometallurgical techniques is in its infancy in Europe with one deposit in Turkey planning to use atmospheric heap leaching to recover nickel and copper from oxide-dominated ores. More widespread implementation of these methods to mineralogically suitable ore types could unlock the highly significant undeveloped resources (with metal contents >0.04% Co and >1% Ni), which have been defined throughout the Balkans eastwards into Turkey. At a conservative estimate, this region has the potential to supply up to 30% of the EU cobalt requirements.

Extraction of copper from an oxidized (lateritic) ore using bacterially catalysed reductive dissolution.

PubMed

Nancucheo, Ivan; Grail, Barry M; Hilario, Felipe; du Plessis, Chris; Johnson, D Barrie

2014-01-01

An oxidized lateritic ore which contained 0.8 % (by weight) copper was bioleached in pH- and temperature-controlled stirred reactors under acidic reducing conditions using pure and mixed cultures of the acidophilic chemolithotrophic bacterium Acidithiobacillus ferrooxidans. Sulfur was provided as the electron donor for the bacteria, and ferric iron present in goethite (the major ferric iron mineral present in the ore) acted as electron acceptor. Significantly more copper was leached by bacterially catalysed reductive dissolution of the laterite than in aerobic cultures or in sterile anoxic reactors, with up to 78 % of the copper present in the ore being extracted. This included copper that was leached from acid-labile minerals (chiefly copper silicates) and that which was associated with ferric iron minerals in the lateritic ore. In the anaerobic bioreactors, soluble iron in the leach liquors was present as iron (II) and copper as copper (I), but both metals were rapidly oxidized (to iron (III) and copper (II)) when the reactors were aerated. The number of bacteria added to the reactors had a critical role in dictating the rate and yield of copper solubilised from the ore. This work has provided further evidence that reductive bioprocessing, a recently described approach for extracting base metals from oxidized deposits, has the potential to greatly extend the range of metal ores that can be biomined.

Understanding the residence of Co in ore minerals - towards the development of novel Co extraction strategies for laterite deposits

NASA Astrophysics Data System (ADS)

Dybowska, Agnieszka; Norman, Rachel; Schofield, Paul; Herrington, Richard

2017-04-01

Cobalt has unique properties highly valued for many applications essential to the green economy. It has been classified as a critical raw material due to the particularly high risk of supply shortage and its importance for the value chain. Despite low crustal abundance (25ppm), Co is concentrated by various geological processes to concentrations suitable for mining, however the majority of Co is recovered as a by-product of Cu and Ni processing in three principal geological settings: hydrothermal, magmatic and lateritic. Cobalt-rich laterites, which provide 20% of the world's Co, are mainly processed using energy-inefficient pyrometallurgical techniques or high-pressure acid leaching technologies often optimised for extraction of other elements, which can leave between 50 and 80% of the Co unrecovered. In order to develop more efficient Co extraction strategies, understanding the residence of Co in ore minerals is essential. To this end, we are undertaking a detailed mineralogical, chemical and atomistic-scale characterization of Co in samples from a range of laterite deposits. Bulk samples representative of the average ore material were sourced from a variety of undeveloped laterite deposits: Shevchenko (Kazakhstan), Acoje (Philippines), Nkamouna (Cameroon) and Piauí (Brazil). Bulk chemical and mineralogical characterisation was undertaken with ICP-OES/MS and XRD, followed by spatially resolved chemical and mineralogical imaging at the micron scale using µXRD, EPMA, SEM and synchrotron-based µXRF. The chemical state and local environment of Co were determined using X ray spectroscopy (μXANES and μEXAFS). The total concentrations of Co ranged from 630 to 2780 mg/kg. The ore mineral assemblage in the various samples includes goethite, maghemite, hematite, quartz, talc, serpentines, chlorites, smectites, kaolinite and chromites. Manganese oxide minerals are present but, due to their poor crystallinity and low concentration, are not routinely detectable with bulk XRD. These low abundance minerals, identified in the samples using Raman spectroscopy, µXRD and EPMA, proved however to be very important Co-hosting phases. Electron microscopy and µ-XRF mapping revealed a strong Mn and Co association in all samples but little correlation between Co and Fe. The important determinant of Co concentration is thus its association with Mn oxides, a variety of which have been found in the samples studied. For example, in Shevchenko laterite asbolane was identified with Co concentrations varying from 0.25 to 12.4 wt% (6.3 wt% on average). Goethite was found to carry only minor Co i.e. below 0.03 wt% or 0.1-0.2 wt%. In samples from the Nkamouna laterite Mn oxide minerals were found to contain Co ranging widely from below 1 wt% in tectomanganate phases such as hollandite and pyrolusite, 5.5% wt% in lithiophorite and up to 21 wt% in lithiophorite-asbolane intermediates. No Co or minor Co (<0.1 wt%) was detected in Fe oxides and oxy-hydroxides. XANES spectroscopy shows that Co is bound in a range of Mn oxide minerals as Co3+. The structural environment of Co in these minerals is very similar with Co in octahedral coordination. Analysis of the EXAFS data for asbolane shows an apparent high degree of structural order around Co which suggest that Co is present as clustered aggregates. Our results indicate that Co should be efficiently and selectively removed from the studied laterites by targeted solubilisation of Mn oxides, which can be achieved via, for example, microbially mediated reductive mineral dissolution.

Au crystal growth on natural occurring Au-Ag aggregate elucidated by means of precession electron diffraction (PED)

NASA Astrophysics Data System (ADS)

Roqué Rosell, Josep; Portillo Serra, Joaquim; Aiglsperger, Thomas; Plana-Ruiz, Sergi; Trifonov, Trifon; Proenza, Joaquín A.

2018-02-01

In the present work, a lamella from an Au-Ag aggregate found in Ni-laterites has been examined using Transmission Electron Microscope to produce a series of Precision Electron Diffraction (PED) patterns. The analysis of the structural data obtained, coupled with Energy Dispersive X-ray microanalysis, made it possible to determine the orientation of twinned native gold growing on the Au-Ag aggregate. The native Au crystal domains are found to have grown at the outermost part of the aggregate whereas the inner core of the aggregate is an Au-Ag alloy (∼4 wt% Ag). The submicron structural study of the natural occurring Au aggregate points to the mobilization and precipitation of gold in laterites and provides insights on Au aggregates development at supergene conditions. This manuscript demonstrates the great potential of electron crystallographic analysis, and in particular, PED to study submicron structural features of micron sized mineral aggregates by using the example of a gold grain found in a Ni-laterite deposits.

Effect of pulp density and particle size on indirect bioleaching of Pomalaa nickel laterite using metabolic citric acid

NASA Astrophysics Data System (ADS)

Petrus, H. B. T. M.; Wanta, K. C.; Setiawan, H.; Perdana, I.; Astuti, W.

2018-01-01

Nickel laterite ore contains oxide of iron, aluminum or both with nickel, cobalt and chromium which can be leached out using hydrometallurgical process. For the purpose of meeting the world’s increasing demand of nickel, there is a need to invent environmentally friendly process to efficiently leach nickel. This experiment used nickel laterite ore obtained from Pomalaa, South Sulawesi. The leaching agent is metabolic citric acid produced by Aspergillus niger under optimum condition. Leaching process was done in three-necked flask in atmospheric temperature and constant stirring speed of 200 rpm. The variable examined in the experiment was pulp density and particle size of nickel laterite ore. Samples were taken at 3, 7, 10, 14, and 17 minutes and then filtered and diluted to be analyzed using ICP-AES. The result of the experiment showed the maximum recovery of metals increase with the decrease of the pulp density. The maximum recovery for varying pulp density were at 5% solid/liquid ratio and the recovery were Ni at 1.63%, Al at 0.47%, Fe at 0.23% and Mg at 1.09%. The effect of particle size on leaching process showed that the leaching process follows the shrinking core model. The maximum recovery of metals at particle size were at 100-120 mesh with Ni at 1.37%, Fe at 0.10%, Al at 0.72% and Mg at 0.62%.

Reconstruction of Post-Deccan topographies from mapping of relict lateritic paleosurfaces: Implications for long-term denudation of Peninsular India

NASA Astrophysics Data System (ADS)

Jean, Amandine; Beauvais, Anicet; Chardon, Dominique; Bonnet, Nicolas; Mudlappa, Jayananda; Janwari, Shazia; Mathé, Pierre-Etienne

2017-04-01

Cenozoic topographic rejuvenation of divergent continental margins and their cratonic hinterland is a matter of debate. For instance, continental scale tilt has been advocated as a cause of Late Cenozoic relief growth of the Indian Peninsula. Our work aims at providing independent geomorphological constraints to test such assertions. The western margin of the Peninsula bears the Western Ghats Escarpment (WGE), which carves both Precambrian rocks and 65 Ma old Deccan Traps. The escarpment separates a narrow coastal lowland plain drained to the Arabian Sea from a highland plateau drained towards the Bengal Sea. Alternating and coupled chemical weathering and erosion led to formation and dissection of lateritic paleolandscapes preserved both sides of the WGE. In the highland, the relicts of three distinctive lateritic surfaces are recognized. They formed successively from 53 Ma to 23 Ma on the basis of ages obtained by Ar-Ar dating of K-rich manganese oxides [1]. The first surface is topped by a duricrust rich in Al (bauxite) forming mesas at altitudes of 960 to 1400 m. The second surface called "Intermediate" is mantled by a ferricrete, whose relicts remain 100 m below the bauxite at altitudes of 850 to 1250 m. The third surface corresponds to the relicts of a lateritic pediment, which may be capped by a ferricrete at altitudes of 600 to 900 m. Three lateritic surfaces have been documented in the lowland. The Ar-Ar ages obtained indicate common lateritic weathering in both the highland and the lowland between at 53-45 Ma, then a divergence later on [1]. The oldest remnants of lateritic surface in the lowland are preserved at maximum elevation of 400-500 m close to the WGE and correspond to a pediment. This ancient landform was re-altered at 24-19 Ma to form residual hills of the "Intermediate" relief (ca. 350-200 m). A younger pediment formed around the residual hills and is preserved at ca. 150-50 m elevation. Relicts' elevations of the three surfaces have been retrieved in both the lowland and the highland to reconstruct successive topographies across the WGE and estimate relief evolution and erosion budgets for major time steps. The results suggest that the denudation did not exceed 10 m/my in the Highland since 45 Ma, and is less than 11 m/my since mitigation of chemical weathering ca. 23 Ma ago. In the lowland, denudation was limited to 5 m/my since 45 Ma and less than 6 m/my since 19 Ma, implying negligible reworking of the WGE, which stabilized at least 50 Ma ago [2]. These results have major implications for relief evolution of South India. They imply very low relief growth since the Eocene and do not require a tilt of the Peninsula. They further put constraints on sedimentary supplies to both margins of the Peninsula over the last 50 Ma. [1] Bonnet et al., 2016, Chemical Geology 446, 33-53. [2] Beauvais et al., 2016, Geology 44, 299-302.

Effective use of iron-aluminum rich laterite based soil mixture for treatment of landfill leachate.

PubMed

Nayanthika, I V K; Jayawardana, D T; Bandara, N J G J; Manage, P M; Madushanka, R M T D

2018-04-01

Landfill leachate poses environmental threats worldwide and causes severe issues on adjacent water bodies and soil by direct discharge. The primary objective of this study is to analyze the efficient use of compost and laterite mixtures (0, 10, 20, 30 and 40 wt% compost/laterite) on leachate treatment and to investigate the associated removal efficiencies under different sorption processes. Therefore, in the experimental design, laterite is used for providing adsorption characteristics, and compost for activating biological properties of the filter. The filtering process is continued until major physical changes occur in the filter at approximately 100 days. The raw leachate used for the experiment shows higher average values for many analyzed parameters. Parameters for the experiment are selected based on their availability in raw leachate in the Sri Lanka. During filtering, removal efficiencies of BOD (>90%), COD (>85%), phosphate (>90%) and nitrate (75-95%) show higher values for all filters. These removals are mainly associated with biodegradation, which is activated by the added compost. Perhaps the removal of nitrate steadily increases with time, which indicates in denitrification by the added excess carbon from the leachate. The removal of total suspended solids (TSS) is moderate to high, but conversely, the electric conductivity (EC) is unsteady, indicating an association between iron exchange and carbonate degradation. A very high removal efficiency is reported in Fe (90-100%), and wide ranges of efficiencies in Mn (30-90%), Cu (45-85%), Ni (30-93%), Cd (37-98%), Zn (15-98%), and Pb (35-98%) involve heterogeneous sorption processes. Furthermore, the normalization of raw leachate by the liquid filtrate has apparent improvements. The differences (p > .05) in removal efficiencies between the filters are significant. It can be concluded that the filter with laterite mixed with 20% of compost has the optimum conditions. Further, the Fourier-transforminfrared (FT-IR) models for filter media conclude multiple sorptions and reveal evidence on vacant sites. X-ray diffraction (XRD) analyses indicate secondary minerals gibbsite, hematite, goethite and kaolinite as the major minerals that involved on the sorption process. Copyright © 2018 Elsevier Ltd. All rights reserved.

Interfacial reactions between humic-like substances and lateritic clay: application to the preparation of "geomimetic" materials.

PubMed

Goure-Doubi, Herve; Martias, Céline; Lecomte-Nana, Gisèle Laure; Nait-Ali, Benoît; Smith, Agnès; Thune, Elsa; Villandier, Nicolas; Gloaguen, Vincent; Soubrand, Marilyne; Konan, Léon koffi

2014-11-15

The aim of this study was to understand the mechanisms responsible for the strengthening of "geomimetic" materials, especially the chemical bonding between clay and humic substances. The mineral matter is lateritic clay which mainly consists in kaolinite, goethite, hematite and quartz. The other starting products are fulvic acid (FA) and lime. The preparation of these geomimetic materials is inspired from the natural stabilization of soils by humic substances occurring over thousands of years. The present process involves acidic and alkaline reactions followed by a curing period of 18days at 60°C under a water saturated atmosphere. The acceleration of the strengthening process usually observed in soils makes this an original process for treatment of soils. The consolidation of the "geomimetic" materials could result from two major phenomena: (i) chemical bonding at the interface between the clay particles and iron compounds and the functional groups of the fulvic acid, (ii) a partial dissolution of the clay grains followed by the precipitation of the cementitious phases, namely calcium silicate hydrates, calcium aluminate hydrates and mixed calcium silicum and aluminum hydrates. Indeed, the decrease of the BET specific area of the lateritic clay after 24 h of reaction with FA added to the structural reorganization observed between 900 and 1000°C in the "geomimetic" material, and to the results of adsorption measurements, confirm the formation of organo-ferric complexes. The presence of iron oxides in clay, in the form of goethite, appears to be another parameter in favor of a ligand exchange process and the creation of binding bridges between FA and the mineral matter. Indeed all faces of goethite are likely to be involved in complexation reactions whereas in lateritic clay only lateral faces could be involved. The results of the adsorption experiments realized at a local scale will improve our understandings about the process of adsorption of FA on lateritic clays and its involvement in the strengthening process of materials. Copyright © 2014 Elsevier Inc. All rights reserved.

Reactive transport model of the formation of oxide-type Ni-laterite profiles (Punta Gorda, Moa Bay, Cuba)

NASA Astrophysics Data System (ADS)

Domènech, Cristina; Galí, Salvador; Villanova-de-Benavent, Cristina; Soler, Josep M.; Proenza, Joaquín A.

2017-10-01

Oxide-type Ni-laterite deposits are characterized by a dominant limonite zone with goethite as the economically most important Ni ore mineral and a thin zone of hydrous Mg silicate-rich saprolite beneath the magnesium discontinuity. Fe, less soluble, is mainly retained forming goethite, while Ni is redeposited at greater depth in a Fe(III) and Ni-rich serpentine (serpentine II) or in goethite, where it adsorbs or substitutes for Fe in the mineral structure. Here, a 1D reactive transport model, using CrunchFlow, of Punta Gorda oxide-type Ni-laterite deposit (Moa Bay, Cuba) formation is presented. The model reproduces the formation of the different laterite horizons in the profile from an initial, partially serpentinized peridotite, in 106 years, validating the conceptual model of the formation of this kind of deposits in which a narrow saprolite horizon rich in Ni-bearing serpentine is formed above peridotite parent rock and a thick limonite horizon is formed over saprolite. Results also confirm that sorption of Ni onto goethite can explain the weight percent of Ni found in the Moa goethite. Sensitivity analyses accounting for the effect of key parameters (composition, dissolution rate, carbonate concentration, quartz precipitation) on the model results are also presented. It is found that aqueous carbonate concentration and quartz precipitation significantly affects the laterization process rate, while the effect of the composition of secondary serpentine or of mineral dissolution rates is minor. The results of this reactive transport modeling have proven useful to validate the conceptual models derived from field observations.

Fractal Theory and Field Cover Experiments: Implications for the Fractal Characteristics and Radon Diffusion Behavior of Soils and Rocks.

PubMed

Tan, Wanyu; Li, Yongmei; Tan, Kaixuan; Duan, Xianzhe; Liu, Dong; Liu, Zehua

2016-12-01

Radon diffusion and transport through different media is a complex process affected by many factors. In this study, the fractal theories and field covering experiments were used to study the fractal characteristics of particle size distribution (PSD) of six kinds of geotechnical materials (e.g., waste rock, sand, laterite, kaolin, mixture of sand and laterite, and mixture of waste rock and laterite) and their effects on radon diffusion. In addition, the radon diffusion coefficient and diffusion length were calculated. Moreover, new formulas for estimating diffusion coefficient and diffusion length functional of fractal dimension d of PSD were proposed. These results demonstrate the following points: (1) the fractal dimension d of the PSD can be used to characterize the property of soils and rocks in the studies of radon diffusion behavior; (2) the diffusion coefficient and diffusion length decrease with increasing fractal dimension of PSD; and (3) the effectiveness of final covers in reducing radon exhalation of uranium tailings impoundments can be evaluated on the basis of the fractal dimension of PSD of materials.

Effects of Palm Kernel Shell Ash on Lime-Stabilized Lateritic Soil

NASA Astrophysics Data System (ADS)

Nnochiri, Emeka Segun; Ogundipe, Olumide M.; Oluwatuyi, Opeyemi E.

2017-09-01

The research investigated the effects of palm kernel shell ash (PKSA) on lime-stabilized lateritic soil. Preliminary tests were performed on three soil samples, i.e., L1, L2 and L3 for identification; the results showed that L1 was A-7-6, L2 was A-7-6, and L3 was A-7-6. The optimum amount of lime for each of the soil samples was achieved. The optimum amount for L1 was 10%, for L2, 8% and for L3, 10%; at these values they recorded the lowest plasticity indexes. The further addition of PKSA was performed by varying the amount of PKSA and lime added to each of the soil samples. The addition of 4% PKSA+ 6% lime, the addition of 4% PKSA + 4% lime, and the addition of 4% PKSA + 6% lime increased the California Bearing Ratio (CBR) to the highest values for L1, L2 and L3 from 8.20%. It was concluded that PKSA can be a suitable complement for lime stabilization in lateritic soil.

Multivariate erosion risk assessment of lateritic badlands of Birbhum (West Bengal, India): A case study

NASA Astrophysics Data System (ADS)

Ghosh, Sandipan; Bhattacharya, Kamala

2012-12-01

Each geomorphic hazard involves a degree of risk which incorporates quantification of the probability that a hazard will be harmful. At present, the categorization of sub-watersheds into erosion risk is considered as the fundamental step to conserve the soil loss. Development of badlands over the laterites of Birbhum district is an indicative of excessive soil loss in the monsoonal wet-dry type of climate. Slope erosion and channel erosion have generated huge amount of sediment from the small watersheds during intense monsoonal rainfall (June-September). The adjoining areas of Rampurhat I Block, Birbhum (West Bengal) and Shikaripara Block, Dumka (Jharkhand) have lost the lateritic soil cover at a rate of 20-40 ton/ha/year (Sarkar et al. 2005). In order to estimate the progressive removal of soil particles from the gully-catchments of the above-mentioned area, different morphometric parameters, soil parameters, hydrologic parameters and empirical models are employed. Side by side, the study is carried out to categorize the gully-catchments into different magnitude of erosion risk using several multivariate statistical techniques.

Effect of hydrated lime on compressive strength mortar of fly ash laterite soil geopolymer mortar

NASA Astrophysics Data System (ADS)

Wangsa, F. A.; Tjaronge, M. W.; Djamaluddin, A. R.; Muhiddin, A. B.

2017-11-01

This paper explored the suitability of fly ash, hydrated lime, and laterite soil with several activator (sodium hydroxide and sodium tiosulfate) to produce geopolymer mortar. Furthermore, the heat that released by hydrated lime was used instead of oven curing. In order to produce geopolymer mortar without oven curing, three variations of curing condition has been applied. Based on the result, all the curing condition showed that the hardener mortar can be produced and exhibited the increasing of compressive strength of geopolymer mortar from 3 days to 7 days without oven curing.

Geochemical and mineralogical constraints on the distribution and enrichment of the rare earth elements during pedogenesis and tropical weathering

NASA Astrophysics Data System (ADS)

Hardy, Liam; Smith, Martin; Moles, Norman; Marsellos, Antonios

2015-04-01

Current European manufacturing relies heavily on imports from the USA & China for unprocessed rare earth elements (REEs) and rare earth oxides (REOs). It has been suggested that the EU holds viable reserves of REEs that, with adequate research, could satisfy 10% of EU industrial demand, by the recycling of mine waste from bauxite production (red muds) alone (Deady, E. (BGS), 2014). Focus has been turned to the potential for Mount Weld type laterite deposits being exploited in the EU, but limited exploration and understanding of EU laterite (& paleo laterite) formations currently makes them unattractive to investment. Although previously researched, the full range of factors influencing the transition of rare earth (primarily lanthanide series, Y & Sc) elements between mineral and clay phases in allochthonous soils, saprolites and laterites is not fully understood, especially in present and Paleo-European environments (Herrington, Boni, Skarpelis, & Large, 2007) (Deady, E. (BGS), 2014) but several deposits globally are suggested to have formed at economically viable concentrations due to this secondary remobilisation & transition from mineral to clay phase and subsequent seasonal leaching and evaporation system, to form depositional buffer zones other than the soil base. (Hoatson, Jaireth, & Miezitis, 2011) (Berger, Janots, Gnos, Frei, & Bernier, 2014). This project intends to use new techniques in sequential extractions, ICP-MS, Quantitative XRD & SEM analysis to expand current knowledge around lateritic & allochtonous ore forming, & weathering processes. Heavy REE content and mineralogical variations in clays will be examined, with examples from a selection of profiles across Southern Europe (and potentially paleo soils from Scandinavia) to define the main influencing factors on REE concentration. Are the specific sites enriched simply by the nature of their source rock (protolith), by the soil formation (pedogenesis), or by biogenic & meteorological factors? These results will then be applied in targeted, environmentally focused exploration projects, and perhaps enhance techniques used industrially for the extraction of HREEs, for less environmentally damaging production in sensitive areas (with current research sites within national parks in Italy and Portugal; and in areas where it is believed more attention should be paid to environmental preservation, including Central Turkey and Southern China). It is hypothesised that: HREE content in tropical laterite formations is due primarily to the source rock's mineralogy, although it's distribution is a result of slower genesis and leaching as opposed to more common biogenetic pedogenesis. It is suggested this distribution initially forms banded horizontal enrichment zones according to protolith, but eventual separation of heavy and light REEs is controlled by clay-surface (the protolith's weathering style), solvent type, fluctuation and availability. It may be found, as in Fe-Ni laterite resources globally (Herrington, Boni, Skarpelis, & Large, 2007) (Eliopoulos, 2000), that high initial bedrock concentrations of REEs are not necessarily required if prolonged weathering continues to concentrate these elements/minerals over longer periods (although this has been found inversely in certain Turkish bauxites (Karadag˘, Peli, Ary, & Ayhan, 2008)). Regardless of eventual concentrations, identifying the argillic phase and the time scales required for clay REE hosting clay formation may broaden the European search for supergene enrichments to REE hosting marine shales, mineral sands and other sedimentary formations that have been long-term- weathered without major displacement.

Corrigendum to “Comparing activated alumina with indigenous laterite and bauxite as potential sorbents for removing fluoride from drinking water in Ghana” [Appl. Geochem. 56 (2015) 50–66

USGS Publications Warehouse

Craig, Laura; Stillings, Lisa; Decker, David L.; Thomas, James M.

2015-01-01

The authors regret that the application of the t-plot to determine the presence of micropores in the three sorbents needs the following corrections: (1) Fig. 1a, c, e are N2(g) adsorption and desorption isotherms” (remove “BET”). This correction applies to descriptions in the text as well. (2) Table 2, the column titled “Micropores” is mislabelled, and should be labelled “Film thickness”, which may not equal the pore width. The column titled “Micropore volume” is a correct description for laterite volume 0.0022 cm3 g−1 (t = 0.3–0.5 nm), but the other pore volumes listed cannot be identified as corresponding to micropores. They likely comprise both micropores and mesopores in laterite, while the presence of micropores in activated alumina is not clear. The positive y-intercept for the lowest linear portion of the laterite t-plot curve indicates micropores (Fig. 1f), and the shape of the t-plot curve suggests the presence of both micropores and mesopores. The shape of the activated alumina t-plot curve suggests the presence of micropores and mesopores, but the zero intercept for the lowest linear portion of the curve (Fig. 1b) creates uncertainty regarding the presence of micropores. Also see Storck et al., 1998; Hay et al. 2011 and references therein. (Additional note: analytical instrument Micromeritics® was misspelled as “Micrometrics”).The authors would like to apologise for any inconvenience caused.

Elemental and isotopic behaviour of Zn in Deccan basalt weathering profiles: Chemical weathering from bedrock to laterite and links to Zn deficiency in tropical soils.

PubMed

Suhr, Nils; Schoenberg, Ronny; Chew, David; Rosca, Carolina; Widdowson, Mike; Kamber, Balz S

2018-04-01

Zinc (Zn) is a micronutrient for organisms and essential for plant growth, therefore knowledge of its elemental cycling in the surface environment is important regarding wider aspects of human nutrition and health. To explore the nature of Zn cycling, we compared its weathering behaviour in a sub-recent regolith versus an ancient laterite profile of the Deccan Traps, India - an area of known soil Zn deficiency. We demonstrate that progressive breakdown of primary minerals and the associated formation of phyllosilicates and iron oxides leads to a depletion in Zn, ultimately resulting in a loss of 80% in lateritic residues. This residue is mainly composed of resistant iron oxides and hydroxides ultimately delivering insufficient amounts of bio-available Zn. Moreover, (sub)-tropical weathering in regions experiencing extended tectonic quiescence (e.g., cratons) further enhance the development of old and deep soil profiles that become deficient in Zn. This situation is clearly revealed by the spatial correlation of the global distribution of laterites, cratons (Africa, India, South America and Australia) and known regions of Zn deficient soils that result in health problems for humans whose diet is derived from such land. We also investigate whether this elemental depletion of Zn is accompanied by isotope fractionation. In the saprolitic horizons of both weathering profiles, compositions of δ 66 Zn JMC-Lyon lie within the "crustal average" of +0.27±0.07‰ δ 66 Zn JMC-Lyon . By contrast, soil horizons enriched in secondary oxides show lighter isotope compositions. The isotopic signature of Zn (Δ 66 Zn sample-protolith up to ~ -0.65‰) during the formation of the ferruginous-lateritic weathering profile likely resulted from a combination of biotically- and kinetically-controlled sorption reactions on Fe-oxyhydroxides. Our findings suggest that oxide rich soil types/horizons in (sub)-tropical regions likely exert a control on riverine Zn isotope compositions such that these become heavier than the crustal average. This isotopic behaviour invites a broader study of global soils to test whether light isotope composition alone could serve as an indicator for reduced bioavailability of Zn. Copyright © 2017 Elsevier B.V. All rights reserved.

Weathering and denudation history of the western continental margin of India constrained by combined Ar-Ar dating and paleomagnetism

NASA Astrophysics Data System (ADS)

Jean, Amandine; Mathé, Pierre-Etienne; Beauvais, Anicet; Chardon, Dominique; Demory, François; Janwari, Shazia

2017-04-01

The western continental passive margin of Peninsular India is fringed by an escarpment, the Western Ghats escarpment (WGE), which separates a narrow coastal lowland plain drained to the west from a highland plateau drained to the east. Since Deccan Traps emplacement, the combined effects of chemical alteration and mechanical erosion led to the formation and dissection of lateritic landscapes whose relicts are preserved both sides of the WGE. Ar-Ar ages of K-rich manganese oxides (cryptomelane) sampled in the lateritic profile of each paleolandscape element have documented the weathering history and put constraints on the paleoclimatic and denudation history of Peninsular India [1,2]. The results have documented intense lateritic weathering during the Eocene (ca. 53-45 Ma) on either sides of the escarpment. Here, we present new independent constraints on the age of that weathering based on paleomagnetism of ferricretes included in thick lateritic weathering mantles of the coastal lowland plain. Our method is based on the paleomagnetic properties of Fe-oxy-hydroxides crystallized in situ in the lateritic weathering profile. The major magnetic minerals, hematite and goethite, have been analyzed by combining hysteresis and remanent magnetizations together with magnetic susceptibility measurements including thermomagnetic curves (KT curves). The main carrier of Natural Remanent Magnetization (NRM) at low temperature is a well-crystallized goethite of first generation characterized by sharp Neel temperature, Tn, at 85°C on KT curves; late goethite generations with distributed Tn below diurnal temperatures (< 65°C) are unable to keep stable NRM. At higher temperature, the component carried by primary and neoformed hematite mimics the primary goethite component. The derived paleopole fits the APWP of India at paleolatitude of 62.3° (with alpha95=5.2°) suggesting an age of ca. 52 Ma [3]. The reverse polarity systematically observed may be ascribed to Chron 23 [4] that refines the paleomagnetic age of the primary goethite to 51.9 - 52.2 Ma. This new age is in agreement with previously obtained Ar-Ar ages in the same weathering mantle upslope the pediment occupying the lowland. These results imply together that the lateritic pediment formed at the foot of the WGE is old, and further attest for very limited denudation of the coastal lowland plain confirming the great stability of the escarpment since at least 50 Ma, despite the negative anomaly of the geoid observed at this latitude. These results have major implications for the Cenozoic topographic evolution of the western continental margin of India, which underwent negligible relief rejuvenation or positive epeirogeny over the last 50 Ma. [1] Bonnet et al., 2016, Chemical Geology 446, 33-53. [2] Beauvais et al., 2016, Geology 44, 299-292. [3] Besse & Courtillot, 1991, J. Geophys. Research 96, 4029-4050 [4] Cande & Kent, 1995, Geomag. Paleomag. Mar. Geol. Geophys. 100, 6093-6095.

Mineralogical and geochemical characterization of supergene Cu-Pb-Zn-V ores in the Oriental High Atlas, Morocco

NASA Astrophysics Data System (ADS)

Verhaert, Michèle; Bernard, Alain; Dekoninck, Augustin; Lafforgue, Ludovic; Saddiqi, Omar; Yans, Johan

2017-10-01

In the Moroccan High Atlas, two sulfide deposits hosted by Jurassic dolostones underwent significant weathering. In the Cu deposit of Jbel Klakh, several stages of supergene mineralization are distinguished: (1) the replacement of hypogene sulfides in the protolith (chalcopyrite) by secondary sulfides in the cementation zone (bornite, digenite, chalcocite, covellite), (2) the formation of oxidized minerals in the saprolite (malachite, azurite, brochantite) where the environment becomes more oxidizing and neutral, and (3) the precipitation of late carbonates (calcite) and iron (hydr-)oxides in the laterite. The precipitation of carbonates is related to the dissolution of dolomitic host rocks, which buffers the fluid acidity due to the oxidation of sulfides. In the Jbel Haouanit Pb-Zn deposit, the mineral assemblage is dominated by typical calamine minerals, Cu minerals (chalcocite, covellite, malachite), and a Cu-Pb-Zn vanadate (mottramite). Galena is successively weathered in anglesite and cerussite. Sphalerite is weathered in smithsonite, which is rapidly replaced by hydrozincite. Late iron (hydr-)oxides are mainly found at the top of both deposits (laterite). Both deposits are thus characterized by specific mineral zoning, from laterite to protolith, related to variations in the mineralogy and ore grades and probably caused by varying Eh-pH conditions.

Effects of Na2SO4 on iron and nickel reduction in a high-iron and low-nickel laterite ore

NASA Astrophysics Data System (ADS)

Wang, Xiao-ping; Sun, Ti-chang; Chen, Chao; Kou, Jue

2018-04-01

This study investigates the reactions of Na2SO4 and its effects on iron and nickel reduction in the roasting of a high-iron and low-nickel laterite ore through gas composition, X-ray diffraction, and scanning electron microscope analyses. Results showed that a reduction reaction of Na2SO4 to SO2 was performed with roasting up to 600°C. However, no clear influence on iron and nickel reductions appeared, because only a small amount of Na2SO4 reacted to produce SO2. Na2SO4 reacted completely at 1000°C, mainly producing troilite and nepheline, which remarkably improves selective reduction of nickel. Furthermore, the production of low-melting-point minerals, including troilite and nepheline, accelerated nickel reduction and delayed iron reduction, which is attributed to the concurrent production of magnesium magnetite, whose structure is more stable than the structure of magnetite. Reduction reactions of Na2SO4 resulted in weakening of the reduction atmosphere, and the main product of Na2SO4 changed and delayed the reduction of iron. Eventually, iron metallization was effectively controlled during laterite ore reduction roasting, leading to iron mainly being found in wustite and high iron-containing olivine.

Adsorption-desorption behavior of atrazine on agricultural soils in China.

PubMed

Yue, Lin; Ge, ChengJun; Feng, Dan; Yu, Huamei; Deng, Hui; Fu, Bomin

2017-07-01

Adsorption and desorption are important processes that affect atrazine transport, transformation, and bioavailability in soils. In this study, the adsorption-desorption characteristics of atrazine in three soils (laterite, paddy soil and alluvial soil) were evaluated using the batch equilibrium method. The results showed that the kinetics of atrazine in soils was completed in two steps: a "fast" adsorption and a "slow" adsorption and could be well described by pseudo-second-order model. In addition, the adsorption equilibrium isotherms were nonlinear and were well fitted by Freundlich and Langmuir models. It was found that the adsorption data on laterite, and paddy soil were better fitted by the Freundlich model; as for alluvial soil, the Langmuir model described it better. The maximum atrazine sorption capacities ranked as follows: paddy soil>alluvial soil>laterite. Results of thermodynamic calculations indicated that atrazine adsorption on three tested soils was spontaneous and endothermic. The desorption data showed that negative hysteresis occurred. Furthermore, lower solution pH value was conducive to the adsorption of atrazine in soils. The atrazine adsorption in these three tested soils was controlled by physical adsorption, including partition and surface adsorption. At lower equilibrium concentration, the atrazine adsorption process in soils was dominated by surface adsorption; while with the increase of equilibrium concentration, partition was predominant. Copyright © 2016. Published by Elsevier B.V.

The removal of fluoride from aqueous solution by a lateritic soil adsorption: Kinetic and equilibrium studies.

PubMed

Iriel, Analia; Bruneel, Stijn P; Schenone, Nahuel; Cirelli, Alicia Fernández

2018-03-01

The use of natural sorbents to remove fluoride from drinking water is a promising alternative because of its low-cost and easy implementation. In this article, fluoride adsorption on a latosol soil from Misiones province (Argentina) was studied regarding kinetic and equilibrium aspects. Experiments were conducted in batch at room temperature under controlled conditions of pH 4-8) and ionic strength (1-10mM KNO 3 ). Experimental data indicated that adsorption processes followed a PSO kinetic where initial rates have showed to be influenced by pH solution. The necessary time to reach an equilibrium state had resulted approximately 30min. Equilibrium adsorption studies were performed at pH 8 which is similar to the natural groundwater. For that, fluoride adsorption data were successfully adjusted to Dubinin-Ataskhov model determining that the fluoride adsorption onto soil particles mainly followed a physical mechanism with a removal capacity of 0.48mgg -1 . Finally, a natural groundwater was tested with laterite obtaining a reduction close to 30% from initial concentration and without changing significantly the physicochemical properties of the natural water. Therefore, it was concluded that the use of lateritic soils for fluoride removal is very promising on a domestic scale. Copyright © 2017 Elsevier Inc. All rights reserved.

Laboratory investigation of TerraZyme as a soil stabilizer

NASA Astrophysics Data System (ADS)

Yusoff, Siti Aimi Nadia Mohd; Azmi, Mastura; Ramli, Harris; Bakar, Ismail; Wijeyesekera, D. C.; Zainorabidin, Adnan

2017-10-01

In this study, a laboratory investigation was conducted to examine the performance of TerraZyme on different soil types. Laterite and kaolin were treated with 2% and 5% TerraZyme to determine changes in the soils' geotechnical properties. The obtained results were analysed and investigated in terms of compaction, Unconfined Compressive Strength (UCS) and California Bearing Ratio (CBR). The changes in geotechnical properties of the stabilised and unstabilised soils were monitored after curing periods of 0, 7, 15, 21 and 30 days. Changes in compaction properties, UCS and CBR were observed. It was found that laterite with 5% TerraZyme gave a higher maximum dry density (MDD) and decreased the optimum moisture content (OMC). For kaolin, a different TerraZyme percentage did not show any effect on both MDD and OMC. For strength properties, it was found that 2% TerraZyme showed the greatest change in UCS over a 30-day curing period. The CBR value of stabilised kaolin with 2% TerraZyme gave a higher CBR value than the kaolin treated with 5% TerraZyme. It was also found that laterite treated with TerraZyme gave a higher CBR value. Lastly, it can be concluded that TerraZyme is not suitable for stabilising kaolin; TerraZyme requires a cohesive soil to achieve a better performance.

In detail monazite characterization in a carbonatite weathering profile - a new tool for landscape geochronology

NASA Astrophysics Data System (ADS)

Renno, A. D.; Le Bras, L.; Ziegenrücker, R.; Couffignal, F.; Wiedenbeck, M.; Haser, S.; Hlawacek, G.

2016-12-01

The Post-Gondwana geology of South Africa is marked by two prominent planation surfaces, the result of two distinct phases of uplift and erosion. The first of these took place during the mid- to late Cretaceous (the so-called "African planation"), whilst the second is tentatively placed into the Miocene or Oligocene (the "Post-African I planation"). Humid and warm climatic conditions are recorded by deep lateritic weathering columns of suitable lithologies. The present study tests the suitability of U-Th-Pb dating on supergene monazite as a geochronometer for landscape formation and the downward progression of the chemical weathering process. We investigated material from the Zandkopsdrift carbonatite, Namaqualand, South Africa, a pipe-shaped intrusion located in the Northern Cape Province of South Africa. The age of carbonatite intrusion has been determined to be Eocene (54-56 Ma). This carbonatite has a well-developed lateritic cap that is more than 80 m thick in places and that is highly enriched in REE's hosted mostly by very fine crystalline monazite of presumably supergene origin. Due to the fact that the age of intrusion postdates the African planation surface, the lateritic cap almost certainly marks the Post-African I erosion surface. Both the onset and duration of the Post-African I cycle of erosion remain uncertain. This study addresses the duration of the Post-African I event through the dating of supergene monazite from the Zandkopsdrift laterite cap. A detailed description of the petrographic and mineralogical properties has identified the most promising samples for dating using secondary ion mass spectrometry (SIMS). A detailed description of the internal structure, microporosity and inclusions as well as intergrowths and pseudomorphic mineral formations has helped greatly toward understand the origins of the Zandkopsdrift sequence and the genesis of the REE within this profile. These data establish important anchor points for the reconstruction of the landscape evolution in South Africa.

Uranium isotope composition of a laterite profile during extreme weathering of basalt in Guangdong, South China

NASA Astrophysics Data System (ADS)

Huang, J.; Zhou, Z.; Gong, Y.; Lundstrom, C.; Huang, F.

2015-12-01

Rock weathering and soil formation in the critical zone are important for material cycle from the solid Earth to superficial system. Laterite is a major type of soil in South China forming at hot-humid climate, which has strong effect on the global uranium cycle. Uranium is closely related to the environmental redox condition because U is stable at U(Ⅳ) in anoxic condition and U(Ⅵ) as soluble uranyl ion (UO22+) under oxic circumstance. In order to understand the behavior of U isotopes during crust weathering, here we report uranium isotopic compositions of soil and base rock samples from a laterite profile originated from extreme weathering of basalt in Guangdong, South China. The uranium isotopic data were measured on a Nu Plasma MC-ICP-MS at the University of Illinois at Urbana-Champaign using the double spike method. The δ238U of BCR-1 is -0.29±0.03‰ (relative to the international standard CRM-112A), corresponding to a 238U/235U ratio of 137.911±0.004. Our result of BCR-1 agrees with previous analyses (e.g., -0.28‰ in Weyer et al. 2008) [1]. U contents of the laterite profile decrease from 1.9 ppm to 0.9 ppm with depth, and peak at 160 - 170 cm (2.3 ppm), much higher than the U content of base rocks (~0.5 ppm). In contrary, U/Th of laterites is lower than that of base rock (0.27) except the peak at the depth of 160-170 cm (0.38), indicating significant U loss during weathering. Notably, U isotope compositions of soils show a small variation from -0.38 to -0.28‰, consistent with the base rock within analytical error (0.05‰ to 0.08‰, 2sd). Such small variation can be explained by a "rind effect" (Wang et al., 2015) [2], by which U(Ⅳ) can be completely oxidized to U(VI) layer by layer during basalt weathering by dissolved oxygen. Therefore, our study indicates that U loss during basalt weathering at the hot-humid climate does not change U isotope composition of superficial water system. [1] Weyer S. et al. (2008) Natural fractionation of 238U/235U. GCA 72,345-359 [2] Wang X. et al. (2015) Isotope fractionation during oxidation of tetravalent uranium by dissolved oxygen. GCA 150, 160-170

Subsurface Reactive Transport Modelling of the Lateritic Ni mineralization in New Caledonia: A coupled Thermo-Hydro-Geochemical Approach

NASA Astrophysics Data System (ADS)

Myagkiy, Andrey; Golfier, Fabrice; Truche, Laurent; Cathelineau, Michel

2017-04-01

This research proposes a subsurface reactive geochemical transport modelling of the development of a nickel laterite profile in New Caledonia over the past few million years. Such a regolith formation from ultramafic bedrock was not yet modelled and gives new profound insights into the Ni vertical mobility, its retention processes in a soil profile and relative enrichment, that are still poorly studied. The downward progression of the lateritization front is allowed by the leaching of the soluble elements (Si, Mg and Ni) through drainage system, represented by porous column of peridotite. Particular emphasis is placed on the detailed understanding of Ni redistribution as a function of time and depth triggered by Ni-bearing silicate precipitation (i.e. garnierite) and by sorption or recrystallization process with goethite. Current work consists of the following models: i) 1-D calculations that are done at 25oC with the code PHREEQC associated with the llnl thermodynamic database and ii) 2-D model that handles coupled thermo-hydro-chemical processes and is calculated on the interface Comsol-Phreeqc (iCP, Nardi et al., 2014). The impact of i) fluid flow in fractures and ii) recharge rate along with iii) hydraulic and iv) geothermal gradients are considered here. While the first model gives profound insights into the vertical mobility of metals upon the formation of laterite (Myagkiy et al, submitted), the latter one additionally allows to describe heterogeneities of mineralizing distributions due to the influence of preferential pathways (fractures), convective flows and lateral transfers. Our long-term 1-D simulations (10 Ma) clearly demonstrate that the Ni enrichment and thickening of iron-rich zone are governed by the vertical progression of the pH front. At the same time 2-D modelling shows reactivation of Ni from oxide zone and it subsequent redistribution and concentration in saprolite. Such a model appears to be of importance in attempt of explanation Ni mineralization processes, revealing the main keys to understanding the trace elements mobility in ultramafic environment. Myagkiy A, Truche L, Cathelineau M, Golfier F. "Revealing the conditions of Ni mineralization in laterite profile of New Caledonia: insights from reactive geochemical transport modelling" Preprint submitted to Chemical Geology (September 28, 2016). Nardi A, Idiart A, Trinchero P, de Vries LM, and Molinero J. "Interface COMSOL-PHREEQC (iCP), an efficient numerical framework for the solution of coupled multiphysics and geochemistry."Computers & Geosciences 69 (2014): 10-21.

Erosion rates and landscape evolution of the lowlands of the Upper Paraguay river basin (Brazil) from cosmogenic 10Be

NASA Astrophysics Data System (ADS)

Pupim, Fabiano do Nascimento; Bierman, Paul R.; Assine, Mario Luis; Rood, Dylan H.; Silva, Aguinaldo; Merino, Eder Renato

2015-04-01

The importance of Earth's low sloping areas in regard to global erosion and sediment fluxes has been widely and vigorously debated. It is a crucial area of research to elucidate geologically meaningful rates of land-surface change and thus the speed of element cycling on Earth. However, there are large portions of Earth where erosion rates have not been well or extensively measured, for example, the tropical lowlands. The Cuiabana lowlands are an extensive low-altitude and low-relief dissected metamorphic terrain situated in the Upper Paraguay river basin, central-west Brazil. Besides exposures of highly variable dissected metamorphic rocks, flat residual lateritic caps related to a Late Cenozoic planation surface dominate interfluves of the Cuiabana lowlands. The timescale over which the lowlands evolved and the planation surface developed, and the rate at which they have been modified by erosion, are poorly known. Here, we present measurements of in situ produced cosmogenic 10Be in outcropping metamorphic bedrock and clastic-lateritic caps to quantify rates of erosion of the surface and associated landforms in order to better understand the Quaternary landscape evolution of these lowlands. Overall, slow erosion rates (mean 10 m/Ma) suggest a stable tectonic environment in these lowlands. Erosion rates vary widely between different lithologies (range 0.57 to 28.3 m/Ma) consistent with differential erosion driving regional landform evolution. The lowest erosion rates are associated with the low-relief area (irregular plains), where clastic-laterite (mean 0.67 m/Ma) and quartzite (mean 2.6 m/Ma) crop out, whereas the highest erosion rates are associated with dissection of residual hills, dominated by metasandstone (mean 11.6 m/Ma) and phyllite (mean 27.6 m/Ma). These data imply that the Cuiabana lowland is comprised of two dominant landform sets with distinct and different dynamics. Because the planation surface (mostly lowlands) is lowering and losing mass more slowly than associated residual hills, regional relief is decreasing over time and the landscape is not in steady state. The extremely slow erosion rates of the clastic-laterite are similar to the slowest outcrop erosion rates reported worldwide. These slow rates are due to the material's properties and resistance, being comprised of quartzite fragments cemented by an iron-rich crust, and reflecting long-term weathering with iron chemical precipitation and ferricrete formation, at least since the Middle Pleistocene. The lateritic caprock appears to be a key factor maintaining hilltop summits of the planation surface over long timescales.

Simultaneous determination of thorium, niobium, lead, and zinc by photon-induced x-ray fluorescence of lateritic material

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaBrecque, J.J.; Adames, D.; Parker, W.C.

1981-01-01

A rapid method is presented for the simultaneous determinations of thorium, niobium, lead, and zinc in lateritic material from Cerro Impacto, Estado Bolivar, Venezuela. This technique uses a PDP - 11/05 processor - based photon induced x-ray fluorescence system. The total variations of approximately 5% for concentrations of approximately 1 and 10% for concentrations of approximately 0.1% were obtained with only 500 s of fluorescent time. The values obtained by this method were in agreement with values measured by conventional flame atomic absorption spectroscopy for lead and zinc. The values for thorium measured were in agreement with the reported valuesmore » for the reference materials supplied by NBL.« less

The influence of tempering process for DP lateritic steel in hardness and microstructure behavior

NASA Astrophysics Data System (ADS)

Hasbi, Muhammad Yunan; Saefudin, Romijarso, Toni Bambang

2018-05-01

In this study, the influence of tempering temperature on dual phase (DP) steel lateritic has been examined. Lateritic is chosen because of its excellence as austenite stabilizer in the formation of martensite and also increase the weldability due to nickel content. The hardness and microstructure behavior of steels were the main focus of this research. One of the goals was to obtain the combination of high strength and ductile materials for automotive application. The specimens used in this study were low carbon steel made by the hot-rolled process and followed by the initial heating process with various temperature (760 °C, 800 °C, 840 °C) continued with rapid cooling. The specimens also conducted by secondary heating with tempering process at 450 °C in an hour with very slow cooling. The experimental results showed that correlation between temperatures with hardness properties of materials. The hardness of the specimens increases as temperature increases. It was because austenite phase has a sufficient time and temperature to form, therefore the amount of transformed austenite becomes martensite was greater. The highest hardness reached by T = 840 °C was 46.98 HRC, it was about 153% from as cast (18.54 HRC). Decreasing in hardness value when the specimen was tempering at 450 °C indicated that martensite phase has been transformed into tempered martensite.

Genèse d'un horizon tacheté par déferruginisation dans une couverture à latérite du Bassin amazonien

NASA Astrophysics Data System (ADS)

Rosolen, Vania; Lamotte, Mathieu; Boulet, René; Trichet, Jean; Rouer, Olivier; José Melfi, Adolpho

A mottled horizon in a laterite cover (without any duricrust) was studied by microscopy and quantitative chemical microanalysis. Apart from the voids, light red spots consisting of Fe-rich particles (≈2 μm) are set in clayey plasma. Dark red spots consisted of concentrations of Fe-rich particles. These patterns are inherited. On the border of structural or biological voids, where Fe-depletion features are systematic, gray or yellow spots result from dissolution of the Fe-rich particles and impregnation of the plasma by iron, respectively. The present Fe-depletion is the dominant process that explains the mottled differentiation and the absence of lateritic duricrust. To cite this article: V. Rosolen et al., C. R. Geoscience 334 (2002) 187-195.

REE concentration processes in ion adsorption deposits: Evidence from Madagascar and China.

NASA Astrophysics Data System (ADS)

Smith, Martin; Estrade, Guillaume; Marquis, Eva; Goodenough, Kathryn; Nasun, Peter; Cheng, Xu; Kynicky, Jindrich

2017-04-01

Lateritic clay deposits, where the rare earth elements (REE) occur adsorbed to clay mineral surfaces, are the world's dominant supply of heavy REE (Gd-Lu). These deposits are currently only mined in China where there is a reported heavy REE enrichment, but other deposits are currently under exploration in Brazil, the Philippines and Madagascar. Concentration of REE within IADs has been proposed to be a dominantly supergene process, where easily degradable REE-minerals (e.g. REE-fluorcarbonates) break down and release REE that are then adsorbed to clay minerals resulting in HREE enrichment. Here we present data from the Ambohimirahavavy Complex, Madagascar, and compare them to data from mineralised profiles in China, with the aim of further constraining the formation and REE enrichment processes in ion adsorption deposits. Bulk rock total REE contents from Madagascar vary from 400-5000ppm, with the HREE varying from 10 to 20% of the TREE. Ammonium Sulphate leaches (designed to remove clay-adsorbed REE) of laterite show leachable TREE from 130-500ppm, with no preferential HREE adsorption. Within the sequential extraction procedure the reducible fraction (hydroxylammonium chloride leach) showed the highest REE, but this is largely attributable to Ce4+ in oxide layers. Analysis of laterite profiles show that the REE distribution is heterogeneous, with control from both bedrock heterogeneity, and the hydrological variation between pedolith and saprolith. Similar patterns are seen in Chinese profiles from Jiangxi province. X-ray diffraction shows the clay fraction in all sites is dominated by kaolinite and halloysite. These data are consistent with experimental data which show that kaolinite is only HREE selective in high ionic strength solutions (Coppin et al., 2002), and suggest that HREE enrichment in lateritic deposits may be a function of exceptional bed rock conditions. Petrographic investigation of the Zhaibei granite, immediately underlying HREE enriched weathering profiles in Jiangxi province has identified the presence of HREE-enriched secondary phases associated with carbonate-rich areas (Xu et al., In press). Neodymium isotope data from primary granitic minerals (ɛNd(t)=-11.5±0.5) contrasts dramatically with data from HREE-enriched minerals (ɛNd(t)=0.9±0.8) indicating that pre-weathering metasomatism from fluids derived from outside the granite system may be critical in the HREE enrichment process of mineralised laterites. This may be important in determining the viability of ion adsorption deposits as HREE resources. Coppin et al. (2002) Sorption of lanthanides on smectite and kaolinite. Chem. Geol. 182, 57-68 Xu et al., (In press) Origin of heavy rare earth mineralization in South China. Nature Comms.

Strontium isotopes reveal weathering processes in lateritic covers in southern China with implications for paleogeographic reconstructions

PubMed Central

Wei, Xiao; Wang, Shijie; Ji, Hongbing; Shi, Zhenhua

2018-01-01

The isotope ratios of Sr are useful tracers for studying parent material sources, weathering processes, and biogeochemical cycling. Mineralogical and geochemical investigations of two lateritic weathering covers, in an area close to the Tropic of Cancer (Guangxi Province, southern China), were undertaken to study the regional weathering processes and Sr isotopic sources. We found that weathering and decomposition of Rb- and Sr-bearing minerals change the Sr isotopic composition in weathering products (lateritic soils). Weathering of illite lowered the 87Sr/86Sr ratio whereas dissolving and leaching of carbonate minerals increased the 87Sr/86Sr ratio. An Fe nodular horizon is widely developed on the top of the weathering covers in the studied area and it differs from the lateritic soil horizon in mineral composition, construction, and elemental concentration. Furthermore, both Fe2O3 and P2O5 (concentrations) are negatively correlated with the 87Sr/86Sr ratios, suggesting fixation of apatite by Fe oxides is a controlling factor of the Sr isotopic composition in the Fe nodular horizon. The 87Sr/86Sr and Nb/Sr ratios imply the contents and proportions of Fe nodules and clay are critical in controlling the changes of Sr isotopic composition in the Fe nodular horizon. The two stages of the weathering process of carbonate rocks are revealed by the87Sr/86Sr versus Nb/Sr diagram. The 87Sr/86Sr and Rb/Sr ratios suggest that Sr isotopes in the weathering covers within the studied area are derived mainly from parent rock weathering and that the contributions from allothogenic Sr isotopes are limited. A comparison of Sr isotopic composition signatures in the weathering covers of the studied area and Guizhou Province provided insight into the Sr isotopic source and paleogeographic evolution of southern China. From the Permian to the Triassic, the continental fragment sources of the South China sedimentary basin changed significantly. In the Permian, Southern China presented the paleogeographic pattern that the north was higher (in elevation) than the south. PMID:29373592

Strontium isotopes reveal weathering processes in lateritic covers in southern China with implications for paleogeographic reconstructions.

PubMed

Wei, Xiao; Wang, Shijie; Ji, Hongbing; Shi, Zhenhua

2018-01-01

The isotope ratios of Sr are useful tracers for studying parent material sources, weathering processes, and biogeochemical cycling. Mineralogical and geochemical investigations of two lateritic weathering covers, in an area close to the Tropic of Cancer (Guangxi Province, southern China), were undertaken to study the regional weathering processes and Sr isotopic sources. We found that weathering and decomposition of Rb- and Sr-bearing minerals change the Sr isotopic composition in weathering products (lateritic soils). Weathering of illite lowered the 87Sr/86Sr ratio whereas dissolving and leaching of carbonate minerals increased the 87Sr/86Sr ratio. An Fe nodular horizon is widely developed on the top of the weathering covers in the studied area and it differs from the lateritic soil horizon in mineral composition, construction, and elemental concentration. Furthermore, both Fe2O3 and P2O5 (concentrations) are negatively correlated with the 87Sr/86Sr ratios, suggesting fixation of apatite by Fe oxides is a controlling factor of the Sr isotopic composition in the Fe nodular horizon. The 87Sr/86Sr and Nb/Sr ratios imply the contents and proportions of Fe nodules and clay are critical in controlling the changes of Sr isotopic composition in the Fe nodular horizon. The two stages of the weathering process of carbonate rocks are revealed by the87Sr/86Sr versus Nb/Sr diagram. The 87Sr/86Sr and Rb/Sr ratios suggest that Sr isotopes in the weathering covers within the studied area are derived mainly from parent rock weathering and that the contributions from allothogenic Sr isotopes are limited. A comparison of Sr isotopic composition signatures in the weathering covers of the studied area and Guizhou Province provided insight into the Sr isotopic source and paleogeographic evolution of southern China. From the Permian to the Triassic, the continental fragment sources of the South China sedimentary basin changed significantly. In the Permian, Southern China presented the paleogeographic pattern that the north was higher (in elevation) than the south.

Land-surface evolution at the continental time-scale: An example from interior Western Australia

NASA Astrophysics Data System (ADS)

Mabbutt, J. A.

1988-12-01

The interior plateau of Western Australia in the Wiluna—Meekatharra area is in part an exhumed pre-Permian surface of low relief and to that extent of Gondwana age. A lateritic duricrust on interfluvial remnants of an Old Plateau surface is probably the outcome of several cycles of weathering and stripping, rather than of a single geomorphic episode. Landforms above the Old Plateau have maintained their relief during this circumdenudation and there is no regional evidence of their isolation by major escarpment retreat. A New Plateau surface has extended by stripping of saprolite and is an etchplain, as also is the Old Plateau under the genesis postulated. The New Plateau cycle was initiated by general drainage rejuvenation whilst lateritic weathering still continued, but its extension was halted through increasing climatic aridity, probably during the Miocene.

Application of Taguchi optimisation of electro metal - electro winning (EMEW) for nickel metal from laterite

NASA Astrophysics Data System (ADS)

Sudibyo, Hermida, L.; Junaedi, A.; Putra, F. A.

2017-11-01

Nickel and cobalt metal able to process from low grade laterite using solvent extraction and electrowinning. One of electrowinning methods which has good performance to produce pure metal is electrometal-electrowinninge(EMEW). In this work, solventextraction was used to separate nickel and cobalt which useCyanex-Versatic Acid in toluene as an organic phase. An aqueous phase of extraction was processed using EMEW in order to deposit the nickel metal in Cathode electrode. The parameters which used in this work were batch temperature, operation time, voltage, and boric acid concentration. Those parameters were studied and optimized using the design of experiment of Taguchi. The Taguchi analysis result shows that the optimum result of EMEW was at 60°C of batch temperature, 2 Voltage, 6 hours operation and 0.5 M of boric acid.

Magnetic multi-metal co-doped magnesium ferrite nanoparticles: An efficient visible light-assisted heterogeneous Fenton-like catalyst synthesized from saprolite laterite ore.

PubMed

Diao, Yifei; Yan, Zhikai; Guo, Min; Wang, Xidong

2018-02-15

Magnetic nanoparticles of multi-metal co-doped magnesium ferrite (MgFe 2 O 4 ) were synthesized from saprolite laterite ore by a hydrothermal method, and firstly proposed as a heterogeneous photon-Fenton-like catalyst for degradation of Rhodamine B (RhB). The factors that influence the degradation reaction including pH value, the concentration of H 2 O 2 and the amount of catalyst, were systematically investigated. The doped MgFe 2 O 4 exhibited a degradation efficiency up to 96.8%, and the chemical oxygen demand (COD) and total organic carbon (TOC) removal efficiencies about 85.6% and 68.3%, respectively, under visible light illumination for 180min. The high activity is mainly attributed to the high specific surface area of the catalyst and the synergistic interaction between photo-catalytic oxidation and Fenton-like oxidation. Moreover, the catalyst also showed good stability and recycling performance for degrading RhB. After five consecutive degradation cycles, the activity decayed no more than 10%. Compared to other catalysts prepared from pure chemical agents, the multi-metal co-doped MgFe 2 O 4 is more competitive due to its high activity, good stability, ease of recollection, and especially the use of saprolite laterite ore as precursor. This work may provide a new avenue to synthesize efficient ferrite catalysts for degrading organic pollutants in wastewater by using natural minerals. Copyright © 2017 Elsevier B.V. All rights reserved.

Modeling thermal performance of exterior walls retrofitted from insulation and modified laterite based bricks materials

NASA Astrophysics Data System (ADS)

Wati, Elvis; Meukam, Pierre; Damfeu, Jean Claude

2017-12-01

Uninsulated concrete block walls commonly found in tropical region have to be retrofitted to save energy. The thickness of insulation layer used can be reduced with the help of modified laterite based bricks layer (with the considerably lower thermal conductivity than that of concrete block layer) during the retrofit building fabrics. The aim of this study is to determine the optimum location and distribution of different materials. The investigation is carried out under steady periodic conditions under the climatic conditions of Garoua in Cameroon using a Simulink model constructed from H-Tools (the library of Simulink models). Results showed that for the continuous air-conditioned space, the best wall configuration from the maximum time lag, minimum decrement factor and peak cooling transmission load perspective, is dividing the insulation layer into two layers and placing one at the exterior surface and the other layer between the two different massive layers with the modified laterite based bricks layer at the interior surface. For intermittent cooling space, the best wall configuration from the minimum energy consumption depends on total insulation thickness. For the total insulation thickness less than 8 cm approximately, the best wall configuration is placing the half layer of insulation material at the interior surface and the other half between the two different massive layers with the modified earthen material at the exterior surface. Results also showed that, the optimum insulation thickness calculated from the yearly cooling transmission (estimated only during the occupied period) and some economic considerations slightly depends on the location of that insulation.

Modes, tempo and spatial variability of Cenozoic cratonic denudation: morphoclimatic constraints from West Africa

NASA Astrophysics Data System (ADS)

Beauvais, Anicet; Chardon, Dominique

2010-05-01

After the onset of Gondwana break-up in the Early Mesozoic, the emerged part of the African plate underwent long Greenhouse effect climatic periods and epeirogeny. The last Greenhouse effect period in the Early Cenozoic and the alternation of wet and dry climatic periods since the Eocene enhanced episodes of rock chemical weathering and laterite production, forming bauxites and ferricretes, interrupted by drier periods of dominantly mechanical denudation, shaping glacis [1]. In Sub-Saharan West Africa, this evolution resulted in pulsate and essentially climatically-forced denudation that has shaped an ubiquitous sequence of five stepped lateritic paleosurfaces that synchronously developed over Cenozoic times. The modes, timing and spatial variability of continental denudation of the region are investigated by combining geomorphologic and geochronological data sets. The geomorphologic data set comprises the altitudinal distribution of the lateritic paleosurfaces relicts and their differential elevation from 42 locations in Sub-Saharan West Africa where the sequence (or part of it) has been documented. The geochronological data set consists in the age ranges of each paleosurface tackled by radiometric 39Ar-40Ar dating of the neoformed oxy-hydroxides (i.e., cryptomelane, K1-2Mn8O16, nH2O, [4]) carried by their laterites at the Tambao reference site, Burkina Faso [1, 3]. Five groups of 39Ar-40Ar ages, ~ 59 - 45 Ma, ~ 29 - 24 Ma, ~ 18 - 11.5 Ma, ~ 7.2 - 5.8 Ma, and ~ 3.4 - 2.9 Ma, characterize periods of chemical weathering whereas the time laps between these groups of ages correspond to episodes of mechanical denudation that reflect physical shaping of the paleosurfaces. For the last 45 Ma, the denudation rate estimates (3 to 8 m Ma-1) are comparable with those derived on shorter time scale (103 to 106 y.) in the same region by the cosmogenic radionuclide method [2]. Combined with the geomorphologic data set, these age ranges allow the visualization of the regional variability in the estimates of local relief and denudation rates for several time spans defined between selected paleosurfaces in the sequence. Denudation rates, ranging from ~ 4 m to ~ 25 m Ma-1, reflect overall acceleration of erosion rates in the Neogene. The observed space-time variability of the denudation rates suggest the interplay of (1) duration and intensity of climatically driven physical erosion periods, (2) absolute elevation and position of the considered sites with respect to the main continental divides, and (3) potential reorganization of the large-scale drainage. The results provide a new perspective for the detection, dating and quantification of subtle epeirogenic movements in West Africa, once combined with the sedimentary record of Cenozoic intracratonic and coastal basins. [1] Beauvais, A., Ruffet, G., Hénocque, O., Colin, F., 2008. Chemical and physical erosion rhythms of the West African Cenozoic morphogenesis: The 39Ar-40Ar dating of supergene K-Mn oxides. J. Geophys. Res. Earth Surface 113, F04007, doi :10.1029/2008JF000996. [2] Brown, E.T., Bourlès, D.L., Colin, F., Sanfo, Z., Raisbeck, G.M., Yiou, F., 1994. The development of iron crust lateritic systems in Burkina Faso, West Africa examined with in-situ-produced cosmogenic nuclides. Earth Planet. Sci. Letters 124, 19-33. [3] Colin, F., Beauvais, A., Ruffet, G., Hénocque, O., 2005. First 40Ar/39Ar geochronology of lateritic manganiferous pisolites: Implications for the palaeogene history of a West African landscape. Earth Planet. Sci. letters 238, 172-188. [4] Vasconcelos, P.M., 1999. K-Ar and 40Ar/39Ar geochronology of weathering processes. Ann. Rev. Earth Planet. Sci. 27, 183-229.

REE in karst bauxites: the Campania example (southern Italy)

NASA Astrophysics Data System (ADS)

Mondillo, N.; Boni, M.; Balassone, G.; Rollinson, G.

2012-04-01

Global production of Rare Earth Element (REE) has dramatically increased in the last years, hence the strong interest to identify new deposits and to understand the processes responsible for their formation. Among REE concentrations related to weathering, the current targets are represented by the ion-adsorption deposit-types, occurring in China, in which REEs are adsorbed onto the surface of clays. Laterites have been also intensively investigated since the discovery of the secondary deposit of Mount Weld (Australia). Most REEs behave as immobile elements in laterites, and tend to be enriched compared to the underlying parent rocks. Many authors debate on a possible REE fractionation along the laterite profiles, resulting in the formation of supergene LREE-minerals. Bauxites are economic Al accumulations, derived from the weathering of alumosilicate-rich parent rocks resulting in the development of laterite profiles. Components as Ca, Mg, K, Si are leached and residual Fe, Al and Ti precipitate in form of hematite>>goethite, gibbsite [Al(OH)3] or amorphous Al hydroxides and anatase. Metabauxites can contain boehmite or diaspore [AlO(OH)]. Chemical composition (including REEs content) of lateritic bauxites generally mirrors the original composition of the parent rock. Geochemistry of REEs in karst bauxites, which lay on carbonate bedrocks and may be also allochthonous to them, is not so straightforward. Cretaceous karst bauxite deposits in the Apennine chain (Southern Italy) are presently uneconomic. A full mineralogical and geochemical study has been performed on several deposits of the Campania district, and three representative profiles have been sampled. In all deposits the bauxite ore has an oolitic-pisolitic texture, but contains also detrital intervals. The mineral association consists of boehmite, kaolinite and hematite, with less goethite and anatase. The main REE-bearing mineral is detrital monazite. In detail, we could detect (SEM) other LREE-phosphates (florencite type minerals) in the Regia Piana deposit and possibly LREE-enriched goethite at Dragoni. QEMSCAN® analysis allowed the identification and location of discrete particles of monazite and xenotime, but because of their very small dimensions (typically <10 microns) it was difficult to determine the exact chemical composition without further investigation. Chemical analyses have shown a total REEs content of 620 ppm on average in all bauxite deposits, with a maximum value of 1454 ppm of total REEs at the top of the Regia Piana profile. The LREE (La-Eu) contents in the samples vary between 200 and 1400 ppm, with positive Ce and La anomalies. The HREE (Gd-Lu) contents are always around 40-60 ppm. The relationship between REEs and the Al and/or Fe values is not clear, probably because the REE content may be slightly biased by the detrital characteristics of the bauxite. The higher Ce and other LREE values, detected at the top of several deposits rather than at the bottom, can be related to LREE supergene minerals occurrence in the higher parts of profile. The Campania deposits represent an interesting case study for REE concentration in karst bauxites. A similar LREE fractionation process could be applied to other bauxite deposits, though related to more favorable parent rocks with sub-economic REE-grades.

THE DEVELOPMENT OF AN INDIGENOUS FLUORIDE FILTER

EPA Science Inventory

Given that an essential component of the design is that it can be adapted for use throughout the world, the potential media investigated are those available in the regions containing fluoride contaminated groundwater. From the literature, wood charcoal, bone char, laterite and...

Comparing activated alumina with indigenous laterite and bauxite as potential sorbents for removing fluoride from drinking water in Ghana

USGS Publications Warehouse

Craig, Laura; Stillings, Lisa; Decker, David L.; Thomas, James M.

2015-01-01

Fluoride is considered beneficial to teeth and bones when consumed in low concentrations, but at elevated concentrations it can cause dental and skeletal fluorosis. Most fluoride-related health problems occur in poor, rural communities of the developing world where groundwater fluoride concentrations are high and the primary sources of drinking water are from community hand-pump borehole drilled wells. One solution to drinking high fluoride water is to attach a simple de-fluoridation filter to the hand-pump; and indigenous materials have been recommended as low-cost sorbents for use in these filters. In an effort to develop an effective, inexpensive, and low-maintenance de-fluoridation filter for a high fluoride region in rural northern Ghana, this study conducted batch fluoride adsorption experiments and potentiometric titrations to investigate the effectiveness of indigenous laterite and bauxite as sorbents for fluoride removal. It also determined the physical and chemical properties of each sorbent. Their properties and the experimental results, including fluoride adsorption capacity, were then compared to those of activated alumina, which has been identified as a good sorbent for removing fluoride from drinking water. The results indicate that, of the three sorbents, bauxite has the highest fluoride adsorption capacity per unit area, but is limited by a low specific surface area. When considering fluoride adsorption per unit weight, activated alumina has the highest fluoride adsorption capacity because of its high specific surface area. Activated alumina also adsorbs fluoride well in a wider pH range than bauxite, and particularly laterite. The differences in adsorption capacity are largely due to surface area, pore size, and mineralogy of the sorbent.

Hydrogeologic and hydraulic characterization of aquifer and nonaquifer layers in a lateritic terrain (West Bengal, India)

NASA Astrophysics Data System (ADS)

Biswal, Sabinaya; Jha, Madan K.; Sharma, Shashi P.

2018-02-01

The hydrogeologic and hydraulic characteristics of a lateritic terrain in West Bengal, India, were investigated. Test drilling was conducted at ten sites and grain-size distribution curves (GSDCs) were prepared for 275 geologic samples. Performance evaluation of eight grain-size-analysis (GSA) methods was carried out to estimate the hydraulic conductivity (K) of subsurface formations. Finally, the GSA results were validated against pumping-test data. The GSDCs indicated that shallow aquifer layers are coarser than the deeper aquifer layers (uniformity coefficient 0.19-11.4). Stratigraphy analysis revealed that both shallow and deep aquifers of varying thickness exist at depths 9-40 and 40-79 m, respectively. The mean K estimates by the GSA methods are 3.62-292.86 m/day for shallow aquifer layers and 0.97-209.93 m/day for the deeper aquifer layers, suggesting significant aquifer heterogeneity. Pumping-test data indicated that the deeper aquifers are leaky confined with transmissivity 122.69-693.79 m2/day, storage coefficient 1.01 × 10-7-2.13 × 10-4 and leakance 2.01 × 10-7-34.56 × 10-2 day-1. Although the K values yielded by the GSA methods are generally larger than those obtained from the pumping tests, the Slichter, Harleman and US Bureau Reclamation (USBR) GSA methods yielded reasonable values at most of the sites (1-3 times higher than K estimates by the pumping-test method). In conclusion, more reliable aquifers exist at deeper depths that can be tapped for dependable water supply. GSA methods such as Slichter, Harleman and USBR can be used for the preliminary assessment of K in lateritic terrains in the absence of reliable field methods.

Preparation of a low-cost and eco-friendly superabsorbent composite based on wheat bran and laterite for potential application in Chinese herbal medicine growth.

PubMed

Gao, Jiande; Liu, Jin; Peng, Hui; Wang, Yaya; Cheng, Sha; Lei, Ziqiang

2018-05-01

A low-cost and eco-friendly superabsorbent composite is prepared through the free-radical graft co-polymerization of wheat bran (WB), acrylic acid (AA) and laterite (LA) in an aqueous solution. Elemental map, scanning electron microscopy and Fourier transform infrared spectra revealed that the LA evenly distributed in the superabsorbent composite and wheat bran-g-poly(acrylic acid)/laterite (WB-g-PAA/LA) formed successfully. Thermogravimetric analysis confirmed that the WB-g-PAA/LA had high thermal stability. Furthermore, the properties of the WB-g-PAA/LA, such as swelling in saline solutions and degradation, are also assessed. The final WB-g-PAA/LA (5 wt%) superabsorbent composite attained an optimum water absorbency of 1425 g g -1 in distilled water and 72 g g -1 in 0.9 wt% NaCl solution. The water absorbency of WB-g-PAA/LA (10 wt%) is even greater than that of the WB-g-PAA. Moreover, the water-retention capacity of WB-g-PAA/LA (5 wt%) is high, and the water-retention process followed a zero-order reaction. The reaction rate constant is 8.2428 × 10 5 exp(- E a /RT ) and the apparent activation energy ( E a ) is 35.11 kJ mol -1 . Furthermore, WB-g-PAA/LA (5 wt%) may regulate the release of urea, indicating that the superabsorbent composite could provide a promising application as a urea fertilizer carrier. Additionally, it increased the germination and growth rates of Glycyrrhiza uralensis Fisch, suggesting it could influence the growth of Chinese herbal medicine.

Evaluation of Strength Characteristics of Laterized Concrete with Corn Cob Ash (CCA) Blended Cement

NASA Astrophysics Data System (ADS)

Ikponmwosa, E. E.; Salau, M. A.; Kaigama, W. B.

2015-11-01

Agricultural wastes are dumped in landfills or left on land in which they constitute nuisance. This study presents the results of investigation of strength characteristics of reinforced laterized concrete beams with cement partially replaced with corn cob (agricultural wastes) ash (CCA). Laterized concrete specimen of 25% laterite and 75% sharp sand were made by blending cement with corn cob ash at 0 to 40% in steps of 10%. A concrete mix ratio of 1:2:4 was used to cast 54 cubes of 150×150×150mm size and 54 beams of dimension 750×150×150mm. The results show that the consistency and setting time of cement increased as the percentage replacement of cement with CCA increased while the workability and density of concrete decreased as the percentage of CCA increased. There was a decrease in compressive strength when laterite was introduced to the concrete from 25.04 to 22.96N/mm2 after 28 days and a continual reduction in strength when CCA was further added from 10% to 40% at steps of 10%. Generally, the beam specimens exhibited majorly shear failure with visible diagonal cracks extending from support points to the load points. The corresponding central deflection in beams, due to two points loading, increased as the laterite was added to the concrete mix but reduced and almost approaching that of the control as 10% CCA was added. The deflection then increased as the CCA content further increased to 20%, 30% and 40% in the mix. It was also noted that the deflection of all percentage replacement including 40% CCA is less than the standard recommended maximum deflection of the beam. The optimal flexural strength occurred with 10% CCA content.

Fe-Ni-bearing serpentines from the saprolite horizon of Caribbean Ni-laterite deposits: new insights from thermodynamic calculations

NASA Astrophysics Data System (ADS)

Villanova-de-Benavent, Cristina; Domènech, Cristina; Tauler, Esperança; Galí, Salvador; Tassara, Santiago; Proenza, Joaquín A.

2017-10-01

Fe-Ni-bearing serpentine from the saprolite horizon is the main Ni ores in hydrous silicate-type Ni laterites and formed by chemical weathering of partially serpentinized ultramafic rocks under tropical conditions. During lateritization, Mg, Si, and Ni are leached from the surface and transported downwards. Fe2+ is oxidized to Fe3+ and fixed as insoluble Fe-oxyhydroxides (mostly goethite) that incorporate Ni. This Ni is later leached from goethite and incorporated in secondary serpentine and garnierite. As a result, a serpentine-dominated saprolite horizon forms over the ultramafic protolith, overlapped by a Fe-oxyhydroxide-dominated limonite horizon. The serpentine from the protolith (serpentine I) is of hydrothermal origin and yields similar Ni (0.10-0.62 wt.% NiO) and lower Fe (mostly 1.37-5.81 wt.% FeO) concentrations than the primary olivine. In contrast, Fe-Ni-bearing serpentine from the saprolite (serpentine II) shows significantly higher and variable Fe and Ni contents, typically ranging from 2.23 to 15.59 wt.% Fe2O3 and from 1.30 to 7.67 wt.% NiO, suggesting that serpentine get enriched in Fe and Ni under supergene conditions. This study presents detailed mineralogical, textural, and chemical data on this serpentine II, as well as new insights by thermodynamic calculations assuming ideal solution between Fe-, Ni- and Mg-pure serpentines. The aim is to assess if at atmospheric pressure and temperature Fe-Ni-bearing serpentine can be formed by precipitation. Results indicate that the formation of serpentine II under atmospheric pressure and temperature is thermodynamically supported, and pH, Eh, and the equilibrium constant of the reaction are the parameters that affect the results more significantly.

Geochemical evidences for palaeoclimatic fluctuations at the Triassic-Jurassic boundary: southwestern margin of the Neotethys in the Salt Range, Pakistan

NASA Astrophysics Data System (ADS)

Iqbal, Shahid; Wagreich, Michael; Jan, Irfanullah; Kürschner, Wolfram Michael; Gier, Susanne

2017-04-01

The Triassic-Jurassic boundary interval reveals a change from warm-arid to a warm and humid climate in the Tethyan domain. Sea-level reconstruction records across the European basins during this interval reveal an end-Triassic global regression event and is linked to the Central Atlantic Magmatic Province (CAMP) activity and Pangaea breakup. In the Tethyan Salt Range of Pakistan a succession of Upper Triassic dolomites/green-black mudstones (Kingriali Formation), overlying quartzose sandstone, mudstones, laterites and Lower Jurassic conglomerates/pebbly sandstones (Datta Formation) provides information on the palaeoclimatic evolution of the area. Preliminary palynological results from the mudstones indicate a Rhaetian age for the Kingriali Formation and a Hettangian age for the Datta Formation. X-ray diffraction (XRD) analysis of the mudstones (upper part of the Kingriali Formation) indicates the presence of mainly illite while kaolinite is a minor component. The kaolinite content, a reflection of the advanced stage of chemical weathering and hence warm-humid conditions, increases up-section in the overlying sandstone-mudstone succession. The overlying laterite-bauxite horizons lack illite/smectite and are entirely composed of kaolinite, boehmite and haematite. At places these kaolinite rich horizons are mined in the area (Western Salt Range). The bulk rock geochemistry of the succession confirms a similar trend. The Chemical Index of Alteration (CIA) displays an increasing trend from the Upper Triassic shales (CIA 75-80) through the overlying sandstones/mudstones-laterites to the overlying quartz rich sandstones and mudstones (CIA 90-97). The overall results for the succession reveal an increasing chemical maturity trend (increase in the intensity of chemical weathering) from Rhaetian to Hettangian thereby supporting a change from warm-arid to a warm-humid palaeoclimate, probably extreme greenhouse conditions.

Preparation of a low-cost and eco-friendly superabsorbent composite based on wheat bran and laterite for potential application in Chinese herbal medicine growth

PubMed Central

Liu, Jin; Peng, Hui; Wang, Yaya; Cheng, Sha; Lei, Ziqiang

2018-01-01

A low-cost and eco-friendly superabsorbent composite is prepared through the free-radical graft co-polymerization of wheat bran (WB), acrylic acid (AA) and laterite (LA) in an aqueous solution. Elemental map, scanning electron microscopy and Fourier transform infrared spectra revealed that the LA evenly distributed in the superabsorbent composite and wheat bran-g-poly(acrylic acid)/laterite (WB-g-PAA/LA) formed successfully. Thermogravimetric analysis confirmed that the WB-g-PAA/LA had high thermal stability. Furthermore, the properties of the WB-g-PAA/LA, such as swelling in saline solutions and degradation, are also assessed. The final WB-g-PAA/LA (5 wt%) superabsorbent composite attained an optimum water absorbency of 1425 g g−1 in distilled water and 72 g g−1 in 0.9 wt% NaCl solution. The water absorbency of WB-g-PAA/LA (10 wt%) is even greater than that of the WB-g-PAA. Moreover, the water-retention capacity of WB-g-PAA/LA (5 wt%) is high, and the water-retention process followed a zero-order reaction. The reaction rate constant is 8.2428 × 105 exp(−Ea/RT) and the apparent activation energy (Ea) is 35.11 kJ mol−1. Furthermore, WB-g-PAA/LA (5 wt%) may regulate the release of urea, indicating that the superabsorbent composite could provide a promising application as a urea fertilizer carrier. Additionally, it increased the germination and growth rates of Glycyrrhiza uralensis Fisch, suggesting it could influence the growth of Chinese herbal medicine. PMID:29892438

The effect of entry into force of the mining law 2009 began January 2014 in the production of NPI (Nickel Pig Iron) in China

NASA Astrophysics Data System (ADS)

Prasetyo, P.

2018-01-01

China is the largest producer NPI (Nickel Pig Iron) obtained from the processing of the low grade laterite (oxide ore) with pyrometallurgical process. Furthermore NPI is used as substitute FeNi (Ferro Nickel) to make stainless steel (SS). The low grade laterite are imported from Philippines and Indonesia because China does not have the natural resources of laterite. China mainly imported limonite contains Ni < 1.5 % from Philippines and the low grade saprolite contains Ni > 1.5 % from Indonesia. The entry into force of the Mining Law 2009 began January 12, 2014 which prohibits the export of the raw materials of mineral, and obliged to process minerals in Indonesia. Applicability of the legislation automatically affects the production of NPI in China. The effects in the short term since the enactment of the Act, the production of NPI declined and imports FeNi increased in China in 2014/2015. So that in anticipation, the NPI producers in China are trying to relocate the NPI plant out of China especially to Indonesia. For the producers who do not relocate the NPI plant, they tried to get the low grade saprolite from the other country especially from Philippines. If the NPI factory from China is relocated to Indonesia, it seems that China is likely to relocate the NPI plant to Indonesia. So in anticipation of the government must make government regulations (GR/PP: Peraturan Pemerintah) which in principle do not harm Indonesia. The government regulation (GR/PP) is to be mutually beneficial to both parties or win-win solution. This reality will be studied in this paper.

Evaluation of shrinking core model in leaching process of Pomalaa nickel laterite using citric acid as leachant at atmospheric conditions

NASA Astrophysics Data System (ADS)

Wanta, K. C.; Perdana, I.; Petrus, H. T. B. M.

2016-11-01

Most of kinetics studies related to leaching process used shrinking core model to describe physical phenomena of the process. Generally, the model was developed in connection with transport and/or reaction of reactant components. In this study, commonly used internal diffusion controlled shrinking core model was evaluated for leaching process of Pomalaa nickel laterite using citric acid as leachant. Particle size was varied at 60-70, 100-120, -200 meshes, while the operating temperature was kept constant at 358 K, citric acid concentration at 0.1 M, pulp density at 20% w/v and the leaching time was for 120 minutes. Simulation results showed that the shrinking core model was inadequate to closely approach the experimental data. Meanwhile, the experimental data indicated that the leaching process was determined by the mobility of product molecules in the ash layer pores. In case of leaching resulting large product molecules, a mathematical model involving steps of reaction and product diffusion might be appropriate to develop.

Section of Permian deposits and fusulinids in the Halvan Mountains, Yazd province, Central Iran

NASA Astrophysics Data System (ADS)

Leven, E. Ya.; Gorgij, M. N.

2009-04-01

The Permian section situated northwest of Tabas in the Halvan Mountains is studied and fusulinids occurring in the section are described. The Chili, Sartakht, and Hermez formations distinguished in the section are separated by horizons of bauxitic laterite and belong to the Khan Group formerly ranked as a synonymous formation. Fusulinids occur at two levels in the section. The lower one confined to the Chili Formation yields the so-called Kalaktash fusulinid assemblage of the late Sakmarian age. The second late Asselian assemblage has been discovered in pebbles from conglomerate-breccia in the basal laterite of the Sartakht Formation. A brief characterization of fusulinids is presented and three new species are described. The new Benshiella genus is discriminated from the Rugosofusulinidae family. As Skinner and Wilde (1965, 1966) changed the original diagnosis of the Pseudofusulina genus, we suggest, regarding all species, which have been attributed to this genus but do not satisfy the new diagnosis, as representing the new Nonpseudofusulina genus.

ENGINEERING-GEOLOGY SITE APPRAISAL OF THE FEDERAL CAPITAL TERRITORY, NIGERIA.

USGS Publications Warehouse

Ege, J.R.; Griffitts, W.R.; Overstreet, W.C.

1985-01-01

The 7,700-km**2-area Federal Capital Territory, Nigeria, is underlain by crystalline igneous and metamorphic rocks of Precambrian age. Laterite caps many hills of Cretaceous rock, some hills of Precambrian rock, and crops out near stream banks in the east and northeast. The most conspicuous structural features are a broad 'J'-shaped fold traversing the eastern and central part of the Territory and a north-trending shear zone along the eastern boundary. The soils of the Territory are lateritic and belong to the SW-SP-SM (Unified Soil Classification System) groups covering Precambrian migmatites, gneisses and granites and the SC group covering Cretaceous sediments and Precambrian mica-rich schists. The engineering characteristics of the rocks are medium- to high-strength massive and gneissic rock, low-to medium-strength bedded rock, and low-strength foliated and sheared rock. An area of at least 800 km**2 is free from apparent geological hazards and should be suitable for construction of a capital city, its environs and supporting facilities.

Evaluation of Sintering Behaviors of Saprolitic Nickeliferous Laterite Based on Quaternary Basicity

NASA Astrophysics Data System (ADS)

Luo, Jun; Li, Guanghui; Rao, Mingjun; Zhang, Yuanbo; Peng, Zhiwei; Zhi, Qian; Jiang, Tao

2015-09-01

The sintering behaviors of saprolitic nickeliferous laterite with various quaternary basicities [(CaO + MgO)/(SiO2 + Al2O3) mass ratio] in a reductive atmosphere are investigated by simulative sintering and validated by sintering pot tests. The simulative sintering results show that the generation of diopside (CaMgSi2O6) with low melting point is the key reason for the decrease in characteristic fusion temperatures when the quaternary basicity increases from 0.5 to 0.8-1.0. Continuous increase of basicity leads to transformation of diopside (CaMgSi2O6) into akermanite (Ca2MgSi2O7), which adversely increases the characteristic fusion temperatures. These findings are confirmed by the sinter pot tests, which demonstrate that the sintering indexes including vertical sintering velocity (VSV), yield ( Y), and productivity ( P), can be improved by optimizing quaternary basicity. At basicity of 1.0, the VSV, Y, P, and ISO tumbling index reach 49.2 mm/min, 80.5%, 1.0 t/(h m2), and 66.5%, respectively.

Control of autoclave scaling during acid pressure leaching of nickeliferous laterite ore

NASA Astrophysics Data System (ADS)

Queneau, P. B.; Doane, R. E.; Cooperrider, M. W.; Berggren, M. H.; Rey, P.

1984-09-01

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMAX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the area of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel-and magnesium-rich serpentine while maintaining acid utilization efficiency. Scale formation is minimized by combining staged acid addition with vigorous agitation and 270 °C operation. This paper describes how advantage can be taken of MgSO4· XH2O precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4 · XH2O matrix. Cooling the autoclave from its 270 ·C operating temperature down to 180 ·C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Lower Tertiary laterite on the Iceland-Faeroe Ridge and the Thulean land bridge

USGS Publications Warehouse

Nilsen, T.H.

1978-01-01

CORES of a lower Tertiary lateritic palaeosol resting on basalt were recovered1 from Deep Sea Drilling Project Site 336 (Leg 38) on the north-east flank of the Iceland-Faeroe Ridge (Fig. 1), a major aseismic oceanic ridge that, together with Iceland, forms the Icelandic transverse ridge 2. The transverse ridge extends from the West European continental margin to the East Greenland continental margin, forming the geographic boundary and a partial barrier to flow of water between the Norwegian-Greenland Sea to the north and the northern North Atlantic Ocean to the south. The palaeosol indicates that at least part of the Iceland-Faeroe Ridge was above sea level during early Tertiary time3. Palaeogeographic and palaeooceanographic reconstructions suggest that it formed the main part of the Thulean land bridge that connected South-east Greenland and the Faeroe islands during the early Tertiary4. This report summarises the subsidence history of the Iceland-Faeroe Ridge relative to early Tertiary seafloor spreading, basaltic volcanism, and the development of the proposed Thulean land bridge. ?? 1978 Nature Publishing Group.

Mineral resources of parts of the Departments of Antioquia and Caldas, Zone II, Colombia

USGS Publications Warehouse

Hall, R.B.; Feininger, Tomas; Barrero, L.; Dario, Rico H.; ,; Alvarez, A.

1970-01-01

The mineral resources of an area of 40,000 sq km, principally in the Department of Antioquia, but including small parts of the Departments of Caldas, C6rdoba, Risaralda, and Tolima, were investigated during the period 1964-68. The area is designated Zone II by the Colombian Inventario Minero Nacional(lMN). The geology of approximately 45 percent of this area, or 18,000 sq km, has been mapped by IMN. Zone II has been a gold producer for centuries, and still produces 75 percent of Colombia's gold. Silver is recovered as a byproduct. Ferruginous laterites have been investigated as potential sources of iron ore but are not commercially exploitable. Nickeliferous laterite on serpentinite near Ure in the extreme northwest corner of the Zone is potentially exploitable, although less promising than similar laterites at Cerro Matoso, north of the Zone boundary. Known deposits of mercury, chromium, manganese, and copper are small and have limited economic potentia1. Cement raw materials are important among nonmetallic resources, and four companies are engaged in the manufacture of portland cement. The eastern half of Zone II contains large carbonate rock reserves, but poor accessibility is a handicap to greater development at present. Dolomite near Amalfi is quarried for the glass-making and other industries. Clay saprolite is abundant and widely used in making brick and tiles in backyard kilns. Kaolin of good quality near La Union is used by the ceramic industry. Subbituminous coal beds of Tertiary are an important resource in the western part of the zone and have good potential for greater development. Aggregate materials for construction are varied and abundant. Deposits of sodic feldspar, talc, decorative stone, and silica are exploited on a small scale. Chrysotils asbestos deposits north of Campamento are being developed to supply fiber for Colombia's thriving asbestos-cement industry, which is presently dependent upon imported fiber. Wollastonite and andalusite are potential resources not exploitable now.

Chemical and physical erosion rhythms of the West African Cenozoic morphogenesis: The 39Ar-40Ar dating of supergene K-Mn oxides

NASA Astrophysics Data System (ADS)

Beauvais, Anicet; Ruffet, Gilles; HéNocque, Olivier; Colin, Fabrice

2008-12-01

Chemical weathering and mechanical erosion are first-order processes of long-term tropical morphogenesis, which is still poorly deciphered for lack of time constraints. We address this issue by laser probe 39Ar-40Ar dating of generations of cryptomelane [K1-2Mn8O16, nH2O] from the manganese ore deposit of Tambao in northern Burkina Faso. This Mn deposit results from the supergene weathering of carbonate and silicate Mn protores underneath lateritic palaeolandsurfaces. It consists of an upper cryptomelane-rich domain and a lower domain where pyrolusite (β-MnO2) is the dominant Mn oxide. The oldest 39Ar-40Ar ages (59-45 Ma) are obtained on surface outcrops while the youngest ones characterize deep oxidation fronts (3.4-2.9 Ma). Apparent correlations of 39Ar-40Ar age groups with δ18O and eustatic curves allow definition of the different stages of morphogenesis. Paleocene-Eocene ages (59-45 Ma) bracket a greenhouse period propitious to bauxitic weathering. The lack of significant ages between ˜45 and 29 Ma characterizes a period dominated by mechanical erosion, during which detrital sediments, including lateritic materials, were accumulated in intracratonic basins allowing the exhumation of a new lateritic landsurface. Two major weathering periods separated by a second erosion episode (24-18 Ma) are also depicted at the end of Oligocene (29-24 Ma) and lower to mid-Miocene (18-11.5 Ma) in the upper domain, during which newly shaped land surfaces conspicuously weathered. The shorter-weathering and erosion episodes recorded in the lower domain from ˜18 to ˜2.9 Ma led to the final geomorphic changes that were conducive to the formation of glacis. The preservation of old cryptomelane (59-45 Ma) in the upper part of the ore deposit indicates a Cenozoic denudation limited to the erosion of previous bauxites, and partly, of ferricretes.

Magnetic fabrics and fluid flow directions in hydrothermal systems. A case study in the Chaillac Ba-F-Fe deposits (France)

NASA Astrophysics Data System (ADS)

Sizaret, Stanislas; Chen, Yan; Chauvet, Alain; Marcoux, Eric; Touray, Jean Claude

2003-02-01

This study presents a possible use of anisotropy of magnetic susceptibility (AMS) to describe the mineralizing process in hydrothermal systems. Ba-F-Fe-rich deposits within the Chaillac Basin are on the southern border of the Paris Basin. In these deposits hydrothermal textures and tectonic structures have been described in veins, sinters, and sandstone cemented by hydrothermal goethite. 278 oriented cores from 24 sites have been collected in these formations. In addition, a lateritic duricrust superimposed on the hydrothermal formation has been sampled. Rock magnetic investigations show that the principal magnetic carrier is goethite for the hydrothermal mineralization and for the laterite level. The AMS measurements show distinguishable behaviors in the different mineralogical and geological contexts. The K1 magnetic lineation (maximum axis) is strongly inclined for the vertical veins. For the horizontally mineralized sinters, the magnetic lineation is almost horizontal with an azimuth similar to the sedimentary flow direction. The AMS of goethite-rich sandstone close to the veins shows strongly inclined K1 as they are probably influenced by the vertical veins; however, when the distance from the vein is larger than 1 m, the AMS presents rather horizontal K1 directions, parallel to the sedimentary flow. The laterite has a foliation dominance of AMS with vertically well-grouped K3 axes and scattered K1 and K2 axes. Field structural observations suggest that the ore deposit is mainly controlled by EW extension tectonics associated with NS trending normal faults. Combining the AMS results on the deposit with vein textures and field data a model is proposed in which AMS results are interpreted in terms of hydrothermal fluid flow. This work opens a new investigation field to constrain hydrodynamic models using the AMS method. Textural study combined with efficient AMS fabric measurements should be used for systematic investigation to trace flow direction in fissures and in sand porosity.

Effect of nonwoven jute agrotextile mulch on soil health and productivity of broccoli (Brassica oleracea L.) in lateritic soil.

PubMed

Manna, Koushik; Kundu, Manik Chandra; Saha, Biplab; Ghosh, Goutam Kumar

2018-01-16

A field experiment was conducted in winter season of 2015-2016 in the dry lateritic soil of Eastern India to study the effect of different thicknesses of nonwoven jute agrotextile mulches (NJATM) along with other mulches on soil health, growth and productivity of broccoli (Brassica oleracea L.). The experiment was conducted in randomized block design with six treatments viz., T 1 (control, i.e. no mulching), T 2 (300 gsm NJATM), T 3 (350 gsm NJATM), T 4 (400 gsm NJATM), T 5 (rice straw) and T 6 (black polythene mulch), each of which was replicated four times. The highest average curd weight (355.25 g) and yield (8.53 t ha -1 ) of broccoli were recorded in T 3 treatment. The lowest density of broad leaved weed, sedges and grasses were recorded in T 6 treatment which was statistically at par with T 4 . All the treatments composing of NJATM increased the population of all the soil microbes except bacteria in the root rhizosphere of broccoli from their initial population. On average, the highest population of fungi (54.0 × 10 3  cfu per g) and actinomycetes (134.75 × 10 3  cfu per g) was recorded with T 3 and T 4 treatments respectively in the post-harvest soil. The soil moisture was conserved in all treatments compared to control showing highest moisture content in T 4 treatment. Organic carbon and available N, P and K contents of soil were increased in all mulch treated plots compared to control, and their initial value and their highest value were recorded in T 3 . The NJATM of 350 gsm thickness was very effective compared to other mulches in increasing the growth and productivity of broccoli by suppressing weeds, increasing moisture, microbial population and nutrient content of the lateritic soil.

Role of phosphate solubilizing Burkholderia spp. for successful colonization and growth promotion of Lycopodium cernuum L. (Lycopodiaceae) in lateritic belt of Birbhum district of West Bengal, India.

PubMed

Ghosh, Ranjan; Barman, Soma; Mukherjee, Rajib; Mandal, Narayan C

2016-02-01

Profuse growth of Lycpodium cernuum L. was found in phosphate deficient red lateritic soil of West Bengal, India. Interaction of vesicular-arbuscular mycorrhiza (VAM) with Lycopodium rhizoids were described earlier but association of PGPR with their rhizoids were not studied. Three potent phosphate solubilizing bacterial strains (P4, P9 and P10) associated with L. cernuum rhizoids were isolated and identified by 16S rDNA homologies on Ez-Taxon database as Burkholderia tropica, Burkholderia unamae and Burkholderia cepacia respectively. Day wise kinetics of phosphate solubilization against Ca3(PO4)2 suggested P4 (580.56±13.38 μg ml(-1)) as maximum mineral phosphate solubilizer followed by P9 (517.12±17.15 μg ml(-1)) and P10 (485.18±14.23 μg ml(-1)) at 28 °C. Release of bound phosphates by isolated strains from ferric phosphate (FePO4), aluminum phosphate (AlPO4) and four different complex rock phosphates indicated their very good phosphate solubilizng efficacy. Nitrogen independent solubilizition also supports their nitrogen fixing capabilities. Inhibition of P solubilization by calcium salts and induction by EDTA suggested pH dependent chelation of metal cations by all of the isolates. Rhizoidal colonization potentials of Burkholderia spp. were confirmed by in planta experiment and also using scanning electron microscope (SEM). Increases of total phosphate content in Lycopodium plants upon soil treatment with these isolates were also recorded. In addition siderophore production on CAS agar medium, tryptophan dependent IAA production and antifungal activities against pathogenic fungi by rhizospheric isolates deep-rooted that they have definite role in nutrient mobilization for successful colonization of L. cernuum in nutrient deficient lateritic soil. Copyright © 2015 Elsevier GmbH. All rights reserved.

Time constraints on post-rift evolution of the Southwest Indian passive margin from ^{40}Ar-^{39Ar dating of supergene K-Mn oxides

NASA Astrophysics Data System (ADS)

Bonnet, Nicolas; Arnaud, Nicolas; Beauvais, Anicet; Chardon, Dominique

2013-04-01

The high-elevation passive margin of Southwest India is marked by the Western Ghats escarpment, which separates the coastal domain from the low-relief East-dipping Mysore plateau. The escarpment has evolved from the Seychelles rifting at ~ 63 Ma following the Deccan traps volcanic event at ~ 65-63 Ma. This escarpment results from differential erosion processes across the passive margin, the rate and timing of which depend upon whether the margin has evolved according to a model of downwarped or rising flank topography. We explore the post-rift evolution of the South Indian passive margin through the characterisation of stepped relicts of lateritic paleosurfaces across that margin, and notably by 40Ar-39Ar dating of in-situ formed K-Mn oxides in supergene Mn-ore deposits carried by these paleosurfaces. The genesis and maturation of Mn-ore deposits are generally linked to progressive weathering processes of the paleosurfaces, which expose them. Dating of K-Mn oxides thus document the timing of these processes [1], and potentially the ages of the altered paleosurface. Moreover, the elevation differences between successive lateritic paleosurfaces of different ages may provide denudation rates for the considered time spans. Previous work (e.g., [2]) and our own field investigations, allow identifying three main lateritic paleosurfaces on the plateau at altitude ranges of 1000-900 m (S2), 900-800 m (S3) and 800-700 m (S3d), and a lower paleosurface in the coastal domain at 150-50 m (S4). K-Mn oxides (cryptomelane) were sampled in Mn ore deposits from different paleosurfaces, particularly in the coastal area around Goa on S4 and in Sandur and Shimoga Mn-ore deposits exposed on S2 and S3. The 40Ar-39Ar ages obtained from carefully characterised mineralogical assemblages range from ~ 26 to ~ 36 Ma in the Sandur Mn-ore deposit indicating intense lateritic weathering processes at the Eocene-Oligocene transition underneath paleosurface S2. Similar ages of ~ 24 and ~ 32 Ma are obtained in two Shimoga Mn ore deposits carried by S3 and S2, respectively. A younger age (~ 21 Ma) is also obtained in a Goa deposit carried by S4. These first results suggest that the Western Ghats passive margin escarpment was established at the latest by early Miocene and that at least part of the inland Mysore plateau morphogenesis was achieved at that time. [1] Beauvais A. et al., Journal of Geophysical Research 113, F04007, 2008. [2] Gunnell, Y., Basin Research 10, 281-310, 1998.

Synthesis and characterization of Co3O4 prepared from atmospheric pressure acid leach liquors of nickel laterite ores

NASA Astrophysics Data System (ADS)

Meng, Long; Guo, Zhan-cheng; Qu, Jing-kui; Qi, Tao; Guo, Qiang; Hou, Gui-hua; Dong, Peng-yu; Xi, Xin-guo

2018-01-01

A chemical precipitation-thermal decomposition method was developed to synthesize Co3O4 nanoparticles using cobalt liquor obtained from the atmospheric pressure acid leaching process of nickel laterite ores. The effects of the precursor reaction temperature, the concentration of Co2+, and the calcination temperature on the specific surface area, morphology, and the electrochemical behavior of the obtained Co3O4 particles were investigated. The precursor basic cobaltous carbonate and cobaltosic oxide products were characterized and analyzed by Fourier transform infrared spectroscopy, thermogravimetric differential thermal analysis, X-ray diffraction, field-emission scanning electron microscopy, specific surface area analysis, and electrochemical analysis. The results indicate that the specific surface area of the Co3O4 particles with a diameter of 30 nm, which were obtained under the optimum conditions of a precursor reaction temperature of 30°C, 0.25 mol/L Co2+, and a calcination temperature of 350°C, was 48.89 m2/g. Electrodes fabricated using Co3O4 nanoparticles exhibited good electrochemical properties, with a specific capacitance of 216.3 F/g at a scan rate of 100 mV/s.

Biocatalytic and chemical leaching of a low-grade nickel laterite ore

NASA Astrophysics Data System (ADS)

Ciftci, Hasan; Atik, Suleyman; Gurbuz, Fatma

2018-04-01

Nickel and cobalt recovery from a low-grade nickel laterite ore, supplied from Çaldağ deposit (Manisa, Turkey) were investigated by bio and chemical leaching processes. The fungus, Aspergillus niger was used for biocatalytic leaching experiments. The effects of parameters (solid ratio and sucrose concentration) on the biocatalytic leaching of the ore were initially tested in flasks to obtain the optimum conditions for the A. niger. Then chemical leaching was applied as a comparison to bioleaching, using organic acids (citric, oxalic, acetic and gluconic acids) as well as a mixture of acids. According the results, the maximum dissolution yield of nickel, cobalt and iron were detected respectively as 95.3%, 74.3% and 50.0% by biocatalytic processes which containing 25% (w/v) sucrose and 1% (w/v) solids. The increase in the solid ratio adversely influenced the biocatalytic activity of A. niger. Finally, further tests in reactors (v = 1 and 10 L) were performed using the optimum conditions from the flask tests. The difference in metals recovery between biocatalytic and chemical leaching was significantly important. Bioleaching produced higher Ni and Co extractions (34.3-75.6%) than chemical process.

Platinum mineralization in the Kapalagulu Intrusion, western Tanzania

NASA Astrophysics Data System (ADS)

Wilhelmij, Harry R.; Cabri, Louis J.

2016-03-01

Low-grade copper and nickel mineralization was found near the eastern shore of Lake Tanganyika at Kungwe Bay in the early part of the twentieth century. The mineralization occurs in harzburgite at the base of a layered gabbro complex known as the Kapalagulu Intrusion, emplaced between the Paleoproterozoic Ubendian basement and overlying Neoproterozoic Itiaso Group metasediments. Several mining and exploration companies continued the geophysical and drilling exploration for base metals throughout the last century culminating in the discovery of high-grade platinum-group element (PGE) mineralization associated with chromitite and sulfide-bearing harzburgite within the southeastern extension of the Kapalagulu Intrusion (known as the Lubalisi Zone) that is covered by a layer of nickel-rich laterite regolith. The poorly layered southeastern harzburgite forms part of the >1500 m-thick Lower Ultramafic Sequence and resembles a dike-like body that flares upwards into a succession of well-layered gabbroic rocks of the Upper Mafic Sequence. No PGE mineralization has been found in the layered gabbro; all the mineralization is associated with the chromite- and sulfide-rich harzburgite of the Lower Ultramafic Sequence and the laterite regolith overlying the mineralized harzburgite. The Lubalisi Zone harzburgite is underlain by basal dunite and overlain by an interval of layered harzburgite and troctolite and this ultramafic sequence is folded into a syncline that plunges towards the northwest that has been modified by major dolerite-filled faults orientated subparallel to the fold axial surface. Extensive deep drilling in the Lubalisi Zone of the Kapalagulu Intrusion shows that the folded harzburgite can be subdivided into a lower feldspathic harzburgite, a harzburgite containing chromitite seams and intervals of sulfide and chromite mineralization known as the Main Chromite Sulfide Succession (MCSS), an overlying sulfide-rich harzburgite, and an upper feldspathic harzburgite. Impersistent, stratiform PGE mineralized horizons occur within the MCSS harzburgite from which drill core samples were taken for platinum-group mineral (PGM) characterization from two drill holes. Where the PGE reefs reach the surface there is residual PGE mineralization within the laterite regolith from which drill core samples were taken from various laterite lithological units for PGM characterization. As the harzburgite PGE reefs contain significant concentrations of both sulfide and chromite (including chromitite seams) they resemble the PGE-rich chromitite seams of the Bushveld Complex rather than the PGE-bearing Main Sulfide Zone of the Great Dyke and Main Sulfide Layer of the Munni Munni Complex. The dominant Pd PGM in three PGE reef samples varies, ranging ( n = 164, relative wt%) from bismuthides (63 %), bismuthtellurides (19 %), and tellurides (6 %), to tellurides (39 %), bismuthtellurides (24 %), stannides (14 %), and alloys (13 %), and to antimon-arsenides (33 %), stannides (21 %), bismuthides (17 %), tellurides (13 %), and alloys (10 %). From 13.5 % to 21.0 % of the total Pd occurs as a solid solution in pentlandite. The three samples have similar Pt PGM modal distributions ( n = 172, relative wt%); the dominant Pt mineral is sperrylite (79, 58, and 47 %) followed by tellurides (15, 17, 21 %), alloys (2, 1, 1 %), and sulfides (2, 1, 0 %). Comparison of Pd/Pt ratios from assays to those calculated from minerals show that the data for the Pt and Pd PGM are very robust, confirming the concentration methodology and characterization. Study of samples from a shallow drill hole penetrating the laterite regolith shows that the primary Pd mineralization has not survived oxidation, is mainly dispersed, but some was reconstituted to form secondary minerals: cabriite, unnamed tellurides, a selenide, a Pd-Te-Hg mineral, alloys and Pd-bearing secondary sulfides (millerite and heazlewoodite). The primary Pt minerals are more resistant to oxidation and dissolution, especially sperrylite and isoferroplatinum, but it is likely that other Pt alloys (tetraferroplatinum and tulameenite) are of secondary origin after dissolution of Pt tellurides.

The potential use of rainwater as alternative source of drinking water by using laterite soil as natural adsorbent

NASA Astrophysics Data System (ADS)

Omar, Khairunnisa Fakhriah Mohd; Palaniandy, Puganeshwary; Adlan, Mohd Nordin; Aziz, Hamidi Abdul; Subramaniam, Ambarasi

2017-10-01

Generally, the rainwater has low concentration of pollutants, whereby it is applicable for domestic water supply. Due to the low concentration of pollutants, further treatment such as adsorption is necessary to treat the harvested rainwater as an alternative source of drinking water supply. Therefore, this research has been carried out to determine the quality of rainwater from different types of locations, which are; rural residential area, urban residential area, agricultural area, industrial area, and open surface. The rainwater sampling was carried out from September 2014 to December 2015. The parameters that have been analysed during the sampling process are chemical oxygen demand (COD), turbidity, heavy metals, and Escherichia coli (E.coli). The sampling results show that the rainwater provides low concentration of contaminants. Thus, it has high potential to be used as alternative source of potable and non potable water supply with a suitable treatment. Due to that, an experimental work contained of 86 of designated experiments for a batch study has been carried out to determine the performance of laterite soil as an adsorbent to remove pollutants that present in the rainwater (i.e. zinc, manganese, and E.coli). The operating factors involved in the experimental works are pH, mass of adsorbents, contact time, initial concentration of zinc, manganese, and E.coli. In this study, the experimental data of the batch study was analysed by developing regression model equation and analysis of variance. Perturbation plots were analysed to determine the effectiveness of the operating factors by developing response surface model, resulting that the high removals of zinc, manganese, and E.coli are 95.8%, 94.05% and 100%, respectively. Overall, this research works found out that the rainwater has a good quality as alternative source of drinking water by providing a suitable treatment. The application of laterite soil as natural adsorbent shows that it has potential to be used as the response surface model provide a good removal for zinc, manganese, and E.coli.

Green and sustainable median on a divided multilane highway

NASA Astrophysics Data System (ADS)

Ambak, K.; Bajuri, F. A. A.; Yusoff, N. A.; Madun, A.; Prasetijo, J.

2017-11-01

The road system in Malaysia showed good growth with increasing number of vehicles on the road. However, statistic of road accident is still at an alarming rate. There are many factor can contribute to the occurrence of an accident. If the accident was caused by road facilities such as street furniture, it is shown that the street furniture was failed to improve the safety of the road users. In this study, a new concept of materials for the construction of road dividers was purpose. The sustainable materials such as laterite soil, Cow Grass, tires and PVC pipes was used to replace the cement and iron guardrails in road divider construction. The main objectives of this study is to design characteristics of a road divider using natural material such as laterite soil, sand, grass and recycle material like used a tyre. A series of experiments such as test liquid limit, plastic limit test, standard proctor test and observations of root growth in 30 days were conducted. The result shows that the plastic index value of 35% was obtained. From the proctor compaction test, the optimum water content was 23% and maximum dry density at 15.3 kN/m3. This value was used to build a prototype of green and sustainable raised road median. The suitability of sand used as the medium in irrigation system was approved. Permeability of sand is 10-2 mm/s to 10 mm/s which is having a high rate of flow. The growth of Cow Grass roots was increased by 4.9 cm in 30 days. This shows that, the grass is suitable to grow in laterite soil and can be used as vegetation material. Through the impact test conducted on a model with a scale of 1:7.5, indicate the initial damage occurred when a force reaches 10N. However, the condition of the model is still stable. From the impact test conducted, the prototype of green and sustainable raised road median has a good potential to be used as existing road divider as it can absorb the impact of an accident.

Gold grade variation and particle microchemistry in exploration pits of the Batouri gold district, SE Cameroon

NASA Astrophysics Data System (ADS)

Vishiti, A.; Suh, C. E.; Lehmann, B.; Egbe, J. A.; Shemang, E. M.

2015-11-01

The Batouri area hosts lode-gold mineralization under several-m-thick lateritic cover. Pitting to bed rock on a geochemical Au anomaly defined from previous reconnaissance soil sampling identified five horizons ranging from saprock at the base to laterite at the top. Analysis of bulk samples from each horizon by fire assay shows that most of the horizons are barren although 119 ppb and 48 ppb Au values were obtained from one laterite horizon and one saprolite horizon, respectively, from two separate pits. All the horizons were panned and particulate gold was also recovered only from these two horizons. The gold grains from both horizons are morphologically and compositionally indistinguishable with rare quartz, pyrite and galena inclusions. The grains have irregular, sub-rounded, bean to elongated shapes and they show a remarkable core-rim zonation. Electron microprobe analysis of the grains recorded high gold content in the rims (86.3-100 wt%) and along fissures within the grains (95.1-100 wt%). The cores are relatively Ag rich (11.8-14 wt% Ag) while the rims (0.63-13.7 wt% Ag, most of the values fall within the lower limit of this range) and fissures (0.03-5.02 wt% Ag) are poor in Ag. The low Ag concentration in the rims and along fissures is attributed to preferential leaching of Ag; a process recognized in gold grains and platiniferous alloys from alluvia. The core composition of the grains is similar to that of primary gold composition in the bedrock. These results show that gold in the soil is relic particulate gold derived from the primary source with no evidence of secondary gold precipitation in the weathering cycle. In all the pits no horizon was systematically enriched in gold suggesting there has been no chemical remobilization of gold in this environment. Rather the dispersion of gold here is in the particulate form. Therefore combining particulate gold features with assay data is relevant to exploration in such tropical environments.

Metal distribution and mobility in lateritic soils affected by Cu-Co smelting in the Copperbelt district, Zambia

NASA Astrophysics Data System (ADS)

Ettler, Vojtech; Mihaljevic, Martin; Majer, Vladimir; Kribek, Bohdan; Sebek, Ondrej

2010-05-01

The copper smelting activities in the Copperbelt mining district (Zambia) left a huge pollution related to the disposal sites of smelting waste (slags) and to the continuous deposition of the smelter stack particulates in the soil systems. We sampled 196 surface and subsurface soils in the vicinity of the Nkana copper smelter at Kitwe and a 110 cm deep lateritic soil profile in order to assess the regional distribution of metallic contaminants and their vertical mobility. The content of contaminants in soil samples were measured by ICP techniques and the lead isotopic compositions (206Pb/207Pb and 208Pb/206Pb ratios) were determined by ICP-MS. The spatial distribution of the major contaminants (Cu, Co, Pb, Zn) indicated the highest contamination NW of the smelter stack corresponding to the direction of prevailing winds in the area. The highest metal concentrations in soils were: 27410 ppm Cu, 606 ppm Co, 480 ppm Pb, 450 ppm Zn. Lead isotopes helped to discriminate the extent of metallic pollution related to the smelter emissions having similar 206Pb/207Pb ratio of 1.17-1.20 in contrast to the regional background value of 1.32. The investigation of the lateritic soil profile sampled in the near vicinity of the Nkana smelter indicated that contamination is mostly located in the uppermost soil horizons enriched in organic matter (< 10 cm). The sequential extraction procedure indicated that up to 33% of Cu and <10% of Co, Pb and Zn was mobile in the profile, being bound in the exchangeable fraction. However, in the deeper parts of the soil profile, metals were mostly bound in reducible fraction, presumably to hydrous ferric oxides. The combination of sequential extraction and lead isotopic determination indicated that the "mobile" fractions of Pb in the soil profile corresponded to the signatures of smelter particulate emissions (206Pb/207Pb = 1.17-1.20), which means that the anthropogenic emissions are the important source of mobile (and potentially bioavailable) metals.

Adsorption and desorption characteristics of endosulfan in two typical agricultural soils in Southwest China.

PubMed

Qian, Sheng; Zhu, Heng; Xiong, Bailian; Zheng, Guocan; Zhang, Jinzhong; Xu, Weihong

2017-04-01

Endosulfan is an organochlorine pesticide widely used in Southwest China. In this paper, the adsorption and desorption characteristics of endosulfan in two typical agricultural soils (latosol and lateritic red soil) in this area were studied. The results showed that Langmuir isothermal equation could well describe the adsorption thermodynamic characteristics of endosulfan in latosol and lateritic red soil, and the maximum adsorption capacities of α-endosulfan were 0.186 and 0.209 mg/g, while those of β-endosulfan were 0.140 and 0.148 mg/g, respectively. Endosulfan adsorption in the two soils was an exothermic physicochemical process, but dominated by physical process. The adsorption kinetic characteristics of endosulfan in the two soils could be well described by second-order kinetic equation, and the initial rate constants were 0.228 and 0.325 mg/(g min) for α-endosulfan, while those were 0.119 and 0.125 mg/(g min) for β-endosulfan, respectively. The adsorbed endosulfan in the two soils was difficult to be desorbed into the liquid phase, and showed weak desorption hysteresis. These results implied that endosulfan could be firmly adsorbed by the two soils, and their adsorption and desorption abilities may be related to the contents of soil clay and organic matter.

Morphology and composition of gold in a lateritic profile, Fazenda Pison “Garimpo”, Amazon, Brazil

NASA Astrophysics Data System (ADS)

Larizzatti, J. H.; Oliveira, S. M. B.; Butt, C. R. M.

2008-05-01

This study describes the morphological evolution of gold grains in a lateritic weathering profile in an equatorial rainforest climate. Primary sources of gold are quartz veins associated with shallow granophyric intrusion. Gold grains were found in fresh ore, saprolite, transition zones, ferruginous duricrust, red latosol, and yellow latosol. Irregularly shaped grains predominate, with smaller proportions of dendritic and prismatic forms. Gold grains are weathered in the uppermost 10 m of the regolith. Mean gold grain size is maximum in the duricrust (>125 μm) and decreases progressively upward into the yellow latosol (<90 μm). Voids and corrosion pits appear on grain surfaces, and progressive rounding is observed from the bottom of the profile to the top. Gold grains can be classified as either homogeneous or zoned with respect to their chemical composition. Homogeneous grains contain 2-15% Ag (mean 8.3%). Zoned grains have more variable Ag contents; grain cores have means of approximately 10% or 23% Ag, with Ag-poor zones of approximately 3.7% Ag along internal discontinuities and/or outer rims. Formation of Ag-poor rims is due to preferential depletion of silver. Processes responsible for duricrust formation may preserve some grains as large aggregates, but subsequent transformation into latosol further modifies them.

Effects of simulated acid rain on microbial characteristics in a lateritic red soil.

PubMed

Xu, Hua-qin; Zhang, Jia-en; Ouyang, Ying; Lin, Ling; Quan, Guo-ming; Zhao, Ben-liang; Yu, Jia-yu

2015-11-01

A laboratory experiment was performed to examine the impact of simulated acid rain (SAR) on nutrient leaching, microbial biomass, and microbial activities in a lateritic red soil in South China. The soil column leaching experiment was conducted over a 60-day period with the following six SAR pH treatments (levels): 2.5, 3.0, 3.5, 4.0, 4.5, and 5.0 and one control treatment (pH = 7). Compared with the control treatment, the concentrations of soil organic matter, total nitrogen, total phosphorus, total potassium, soil microbial biomass carbon (MBC), soil microbial biomass nitrogen (MBN), and average well color density (AWCD) in the Ecoplates were all significantly decreased by leaching with SAR at different pH levels. The decrease in MBC and MBN indicated that acid rain reduced the soil microbial population, while the decrease in AWCD revealed that acid rain had a negative effect on soil bacterial metabolic function. Soil basal respiration increased gradually from pH 4.0 to 7.0 but decreased dramatically from pH 2.5 to 3.0. The decrease in soil nutrient was the major reason for the change of soil microbial functions. A principal component analysis showed that the major carbon sources used by the bacteria were carbohydrates and carboxylic acids.

Rehabilitating acid soils for increasing crop productivity through low-cost liming material.

PubMed

Bhat, Javid Ahmad; Kundu, Manik Chandra; Hazra, Gora Chand; Santra, Gour Hari; Mandal, Biswapati

2010-09-15

Productivity of red and lateritic soils is low because of their acidity and deficiencies in few essential nutrients viz., nitrogen, phosphorus, calcium, zinc, boron, molybdenum etc. We compared the effectiveness of basic slag, a low-cost liming material, with that of calcite as an ameliorant for these soils using mustard followed by rice as test crops. Experiments were conducted with three levels of each of basic slag and calcite along with a control on farmers' fields at 14 different locations. Influence of farmyard manure (FYM) and poultry manure (PM) on the effectiveness of the slag was also tested. On an average, basic slag performed better than calcite in increasing yields of both mustard and rice and left over higher amounts of available Ca, Si and Zn in residual soils. The slag also improved N, P, K and Ca nutrition of mustard and Si and Zn nutrition of rice with a favorable benefit:cost (B:C) ratio over the calcite (4.82 vs. 1.44). Effectiveness of the basic slag improved when it was applied in combination with FYM or PM (B:C, 5.83 and 6.27). Basic slag can, therefore, be advocated for use in the acidic red and lateritic soils for economically improving their productivity. Copyright 2010 Elsevier B.V. All rights reserved.

Assessment of bauxite, clay, and laterite deposits in Afghanistan

USGS Publications Warehouse

Renaud, Karine M.; Wardlaw, Bruce R.; Hubbard, Bernard E.

2015-01-01

Although some bauxite occurrences were sampled in the course of reconnaissance exploration by Soviet workers in the 1960s and 1970s, the bauxite areas in Afghanistan generally are underexplored. The Obatu Sheila area is a known field of bauxite deposits of Late Jurassic age that had been studied in more detail than other known bauxite deposits and occurrences in Afghanistan. Obatu Sheila has an estimated reserve of 7.2 million tons.

Ground water in folded Cretaceous sandstone of the Bhachau area, Kutch, India, with reference to the Kandla Port water supply

USGS Publications Warehouse

Taylor, George C.; Osa, H.M.; Mitra, A.; Sen, B.N.

1964-01-01

This report is based on an investigation of the availability of ground-water supplies in the Bhachau area for the nearby Kandla Port and township development undertaken by the Government of India. This seaport lies on an estuary of the Gulf of Kutch in western India and in the eastern part of the State of Kutch. The fieldwork on the investigation was carried on from November 1952 through April 1953 with continuing hydrologic observations through 1954-55. The fieldwork included: geologic mapping and delimitation of the principal aquifers of the region; preparation of water-table maps; a detailed inventory of existing wells and springs; observations of significant water table fluctuations; preparation of isobicarb, isochlor and isosulf maps to show the areal distribution of ground-water salinity. The Bhachau area includes about 116 square miles in eastern Kutch and lies in a belt of semiarid low-latitude steppes. The mean annual rainfall is about 15 inches, most of which falls from late June to late September during the southwest monsoon. The area includes a central sandy upland ranging from about 100 to 250 feet above sea level ; a northern lowland of between about 50 to 125 feet altitude that slopes north to the Great Rann of Kutch; a belt of low buttes and discontinuous ridges ranging from about 200 to 275 feet above sea level; and southern lowland which slopes in a southerly to southeasterly direction from an altitude of about 125 feet to 25 feet or less near the Gulf of Kutch. The principal streams are Kageshwar Vokra and Kara Vokra which drain north to the Great Rann and Kotwala Vokra and Dalwala Vokra which drain south toward the Gulf of Kutch. The rocks of the Bhachau area include nonmarine and marine sediments of Mesozoic, Tertiary, and Quaternary age and volcanic rocks of late Mesozoic to early Tertiary age. The oldest rocks in the area are medium- to coarse-grained white to buff current-bedded friable sandstone with occasional partings of white silty shale of the Upper Bhuj series that has been assigned to the Early Cretaceous. The soft friable sandstone of the Upper Bhuj series constitutes the most productive ground-water reservoir in the Bhachau area. At present (1955) there are nine irrigated tracts for which water is obtained from dug wells less than 90 feet deep in the Upper Bhuj. These wells are worked by bullocks and 'motes' (leather bags) at withdrawal rates ranging from about 6,000 to 24,000imperial gallons per day; however, many existing individual wells if equipped with mechanical pumps are capable of yielding 100,000 gallons per day. The Deccan trap of Late Cretaceous to Eocene age occurs in a sequence of basaltic lava flows in the Bhachau area, but trap dikes, sills and plugs that are common in other parts of Kutch have not been observed in the area. Laterite of probable Eocene age is extensive at the top of the Deccan trap, and in places where the lava flows are thin the parent rock has been almost completely lateritized. The Deccan lava flows or the laterite, where the trap is absent, rest disconformably on the Upper Bhuj. No wells have been observed in the Deccan trap of the Bhachau area, but it is possible that locally small supplies of good water may be obtained from these rocks. The Tertiary sediments, which are assigned to the Manchhar series of Pliocene age, generally rest on the laterite or the Deccan trap ; but where both are absent, the Manchhar rests directly on the Upper Bhuj. The Manchhar series includes massive reddish-brown gypseous clay shales, laminated gray siltstones, some limestone, mottled sandstone, and laterite trap gravel. Only meager supplies of brackish water are obtained from wells in these sediments. Along the channels of Kotwala, Dalwala, Kageshwar, and Kara Vokras are narrow bands of unconsolidated coarse sand with fine gravel of Quaternary age. No wells were observed in these deposits, but it is possible that locally they may contain small supplies of bracki

Response of Haloalkaliphilic Archaeon Natronococcus Jeotgali RR17 to Hypergravity

NASA Astrophysics Data System (ADS)

Thombre, Rebecca S.; Bhalerao, Aniruddha R.; Shinde, Vinaya D.; Dhar, Sunil Kumar; Shouche, Yogesh S.

2017-06-01

The survival of archaeabacteria in extreme inhabitable environments on earth that challenge organismic survival is ubiquitously known. However, the studies related to the effect of hypergravity on the growth and proliferation of archaea are unprecedented. The survival of organisms in hypergravity and rocks in addition to resistance to cosmic radiations, pressure and other extremities is imperative to study the possibilities of microbial travel between planets and endurance in hyperaccelerative forces faced during ejection of rocks from planets. The current investigation highlights the growth of an extremophilic archaeon isolated from a rocky substrate in hypergravity environment. The haloalkaliphilic archaeon, Natronococcus jeotgali RR17 was isolated from an Indian laterite rock, submerged in the Arabian sea lining Coastal Maharashtra, India. The endolithic haloarchaeon was subjected to hypergravity from 56 - 893 X gusing acceleration generated by centrifugal rotation. The cells of N. jeotgali RR17 proliferated and demonstrated good growth in hypergravity (223 X g). This is the first report on isolation of endolithic haloarchaeon N. jeotgali RR17 from an Indian laterite rock and its ability to proliferate in hypergravity. The present study demonstrates the ability of microbial life to survive and proliferate in hypergravity. Thus the inability of organismic growth in hypergravity may no longer be a limitation for astrobiology studies related to habitability of substellar objects, brown dwarfs and other planetary bodies in the universe besides planet earth.

Unravelling regolith material types using Mg/Al and K/Al plot to support field regolith identification in the savannah regions of NW Ghana, West Africa

NASA Astrophysics Data System (ADS)

Arhin, Emmanuel; Zango, Saeed M.

2015-12-01

The XRF analytical method was used to measure the weight % of the major oxides in regolith samples. The metal weight % of Mg, K and Al were calculated from their oxides and were normalised relative to immobile Al calculated from its oxide. The plot of Mg/Al and K/Al identified the regolith of the study area to consist of 137 transported clays, 4 ferruginous sediments or ferricrete, 2 lateritic duricrust and 4 saprolites. Surface regolith that had undergone secondary transformation and shows compositional overlaps were 4 transported clays with Fe-oxide impregnation may be referred to as nodular laterite and 5 ferruginous saprolites. The variable regolith materials features identified from the 154 samples enabled the characterisation and identification of the different sample materials because an overprint of bedrock geochemistry is reflected in the regolith. Plot of Mg/Al and K/Al highlighted the compositional variability of the regolith samples and refute the notion of the homogeneity of all the sampled materials in the area. The study thus recognized Mg/Al versus K/Al plots to be used in supporting field identification of regolith mapping units particularly in complex regolith terrains of savannah regions of Ghana and in similar areas where geochemical exploration surveys are being carried out under cover.

High calcium fly ash geopolymer stabilized lateritic soil and granulated blast furnace slag blends as a pavement base material.

PubMed

Phummiphan, Itthikorn; Horpibulsuk, Suksun; Rachan, Runglawan; Arulrajah, Arul; Shen, Shui-Long; Chindaprasirt, Prinya

2018-01-05

Granulated Blast Furnace Slag (GBFS) was used as a replacement material in marginal lateritic soil (LS) while class C Fly Ash (FA) was used as a precursor for the geopolymerization process to develop a low-carbon pavement base material at ambient temperature. Unconfined Compression Strength (UCS) tests were performed to investigate the strength development of geopolymer stabilized LS/GBFS blends. Scanning Electron Microscopy and X-ray Diffraction analysis were undertaken to examine the role of the various influencing factors on UCS development. The influencing factors studied included GBFS content, Na 2 SiO 3 :NaOH ratio (NS:NH) and curing time. The 7-day soaked UCS of FA geopolymer stabilized LS/GBFS blends at various NS:NH ratios tested was found to satisfy the specifications of the Thailand national road authorities. The GBFS replacement was found to be insignificant for the improvement of the UCS of FA geopolymer stabilized LS/GBFS blends at low NS:NH ratio of 50:50. Microstructural analysis indicated the coexistence of Calcium Silicate Hydrate (CSH) and Sodium Alumino Silicate Hydrate products in FA geopolymer stabilized LS/GBFS blends. This research enables GBFS, which is traditionally considered as a waste material, to be used as a replacement and partially reactive material in FA geopolymer pavement applications. Copyright © 2017 Elsevier B.V. All rights reserved.

Ce(III) and Ce(IV) (re)distribution and fractionation in a laterite profile from Madagascar: Insights from in situ XANES spectroscopy at the Ce LIII-edge

NASA Astrophysics Data System (ADS)

Janots, Emilie; Bernier, Felix; Brunet, Fabrice; Muñoz, Manuel; Trcera, Nicolas; Berger, Alfons; Lanson, Martine

2015-03-01

The distribution of trivalent and tetravalent cerium, Ce(III) and Ce(IV) respectively, in a lateritic profile from Madagascar, has been characterized by X-ray-absorption near-edge structure (XANES) spectroscopy at the Ce LIII-edge on the LUCIA beamline (SOLEIL synchrotron, France). XANES spectra were acquired on bulk-rock samples as well as on specific lateritic minerals or polymineral zones (in-situ measurements) of the tonalite bedrock and the three overlying weathered horizons (C-, B- and A-horizons). Geochemically, the bedrock, and the A- and C-horizons show similar rare earth element content (REE = 363-405 mg/kg). They also display the same positive Ce-anomaly (CeCN/Ce∗ = 1.12-1.45), which is therefore likely to be inherited from the bedrock. In the B-horizon, the higher REE content (REE = 2194 mg/kg) and the larger Ce-anomaly (CeCN/Ce∗ = 4.26) are consistent with an accumulation zone caused by the evaporation of groundwater during the dry season. There is a good agreement between the Ce(III)/Cetotal ratio (XCe(III)) deduced from the positive Ce-anomaly (bulk-rock geochemical data) and that derived from XANES spectroscopy on the same bulk-rock samples (BR-XCe(III)-XANES) in the bedrock, and the C- and B-horizons. In the A-horizon, XANES measurements on bulk rock and minerals revealed a higher BR-XCe(III)-XANES (up to 100%) compared to the XCe(III) deduced from geochemical data (XCe(III) = 79%). The preservation of a positive Ce-anomaly in the A-horizon suggests that the Ce mobilization and redistribution during weathering occurred with no significant Ce fractionation from other trivalent REE. Remarkably, the only investigated sample where cerianite is observed belongs to the B-horizon. Within this horizon, Ce oxidation state varies depending on the microstructural position (porosity, cracks, clay-rich groundmass). The highest Ce(IV) concentrations are measured in cerianite (and aluminophosphates) localized in pores at the vicinity of Mn-rich domains (XCe(III)-XANES = 30-51%). Therefore, Ce fractionation from other REE is attributed to a Ce oxidation and precipitation potentially assisted by oxyhydroxide scavenging. In the C-horizon, Ce(III) and Ce(IV) are mainly distributed in REE-minerals of the rhabdophane group found in pores and cracks. The similarity between the Ce(III) proportion of rhabdophane grains (XCe(III)-XANES = 74-89%) with that of the bedrock (BR-XCe(III)-XANES = 79%) suggests no significant fractionation of Ce(III) and Ce(IV) between solution and mineral during the successive stages of primary REE-mineral alteration, transport in solution and secondary precipitation in the incipient stages of weathering. Overall, our novel spectroscopic approach shows that Ce is not necessarily oxidized nor fractionated from other REE during weathering in lateritic conditions. This implies that like Ce(III), Ce(IV) can be mobilized in aqueous fluids during weathering, possibly thanks to complexation with organic molecules, and can precipitate together with Ce(III) in secondary REE-bearing minerals. The corollary is that (paleo)redox reconstructions in soils and/or sediments based on Ce-anomaly in weathered rocks or minerals must be interpreted with caution.

Project CHECO Southeast Asia Report. Forward Airfields for Tactical Airlift in SEA

DTIC Science & Technology

1970-06-15

publications, this is an authen- tic s-sment of the effectiveness of USAF airpower in PACOM. ef /o a , Major General, USAF I/ m i ii l UNCLASSIFIED...Australian Air Force (RAAF) crews were airborne 35,569 times in 1969, with cargo that ranged from troops to chickens, cement , rice, ammunition, cattle...Runway surfaces--clay, laterite , limestone, light steel matting (M8Al), or sod, depending on the aircraft involved-- were expected to sustain 700 traffic

Field recovery of layered tektites in northeast Thailand

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wasson, J.T.; Pitakpaivan, K.; Putthapiban, P.

The authors recovered Australasian tektites in place throughout a 40 X 130 km region in northeast Thailand extending from the Laotian border westward to a line connecting Na Pho Klang in the northeast through Det Udom to Nam Yun in the south. With two exceptions, in sites near the western edge of this region, all fragments are layered (muong-Nong-type) tektites. It appears that large layered tektites are mainly found by rice farmers in fields that were forested until the recent past. The presence of layered tektites in this 40 X 130 km area implies that impact melt that fell inmore » these areas was hot enough to flow if it was deposited on a sloping surface. The absence of splash-form tektites from the region indicates that the layer was still molten when masses having shapes (teardrops, dumbbells, etc.) produced by spinning reached the ground. To account for this and to allow time for the melt to flow a few tens of centimeters requires that the atmosphere remained hot (>2300 K) for a few minutes. Tektites that are in place are almost always associated with a widespread 10-cm to meter-thick layer of laterite. In two cases (one involving layered, one involving splash-form tektites), where accurate stratigraphic control demonstrated that the tektites were still in section, they were sited on top of the laterite layer just below a layer of aeolian sand. 27 refs., 1 fig., 1 tab.« less

Effects of acidic solutions on element dynamics in the monsoon evergreen broad-leaved forest at Dinghushan, China. Part 2: dynamics of Fe, Cu, Mn and Al.

PubMed

Liu, Juxiu; Zhou, Guoyi; Zhang, Deqiang

2007-05-01

Soil metal dynamics are affected by acid deposition. Little knowledge is available about the process in the lateritic soils under the monsoon forest in south China. Samplings of Acmera acuminatissima, Cryptocarya concinna and Schima superba were grown from October, 2000 to July, 2002 in pots with a natural acid lateritic forest soil from Dinghushan. Pots were watered weekly with an acid solution (pH 3.05, 3.52, 4.00 or 4.40) or with tap water. Fe, Mn, Cu and Al were measured in soils, leachates and sapling leaves. Soil extractable Fe and leachate Al and Mn concentrations increased with a decreasing treatment pH. Soil reactive Al exhibited the opposite trend and decreased over time. The Ca/Al and Mg/ (Al+Mn) ratios did not decrease in the leaves of Schima superba, but decreased with a decreasing treatment pH for Cryptocaria concinna. Both ratios only decreased in the pH 3.05 treatment for Acmena Cu will not be toxic for plants since soil extractable Cu was not high and Fe will not be toxic either given that its root uptake was inhibited by Mn. Acid rains will lead to increased Mn and Al mobility in soil. Cryptocaria concinna will be the most sensible species to these changes (nutrient deficiency and direct Mn toxicity), while Schima superba should retain a good growth.

Zinc and copper behaviour at the soil-river interface: New insights by Zn and Cu isotopes in the organic-rich Rio Negro basin

NASA Astrophysics Data System (ADS)

Guinoiseau, Damien; Gélabert, Alexandre; Allard, Thierry; Louvat, Pascale; Moreira-Turcq, Patricia; Benedetti, Marc F.

2017-09-01

The complex behaviour of Zn and Cu at the soil-river interface was investigated in soil and riverine water samples from the Rio Negro basin, a secondary tributary of the Rio Amazonas, using their stable isotope compositions. This acidic and organic river drains two types of intensely weathered terrains: podzols in its upstream part, and lateritic soils downstream. Bulk soil particles, suspended particulate matter (SPM) as well as colloidal fractions were sampled across the whole basin during low and high water stages. In the basin, Zn and Cu are mostly exported from lateritic soils and transported by organic colloids where significant losses are observed in the downstream part of the river. The use of δ66Zn and δ65Cu measurements reveals distinct stories for these two metals in suspended sediments and colloids. In the colloids, the constant δ66Zncoll across the basin is induced by the same weak association mode between Zn and organic ligands, regardless of the origin of the water. By contrast, in SPM, the speciation of Zn and thus δ66ZnSPM differ according to the type of drained soils. Zn is associated with organic complexes in particles exported with water draining podzol whereas Zn2+ is incorporated in the structure of the remaining kaolinite clays in lateritic output. The stronger reactivity of Cu than Zn with organic ligands induces its complete complexation. Copper is controlled by refractory particulate organic matter (POM) and by reactive colloidal organic matter; the latter being enriched in 65Cu due to stronger binding interactions than in POM. While the Cu content remains constant in the upstream part of the Rio Negro, downstream, the decrease of SPM and colloidal Cu fluxes is associated with a constant δ65CuSPM and with an increase of δ65Cucoll at the Rio Negro outlet. Geochemical mass balance modelling, based on SPM, Cu and Zn fluxes in SPM and their associated isotopic signatures, confirms distinct host phases for Zn and Cu, and identifies the most probable places where losses of these two metals occur. In colloids, the observed Cu isotope fractionation (from 0.24 to 0.45‰) superimposed on the significant Cucoll loss is assumed to result from a new isotopic equilibrium in a low velocity and high productivity zone: Cu-rich colloids enriched in 63Cu aggregate and settle down, whereas the remaining heavy Cu is partially complexed on strong organic ligands secreted by phytoplankton, forming new Cu-colloids.

Unraveling climatic changes from intra-profile variation in oxygen and hydrogen isotopic composition of goethite and kaolinite in laterites: An integrated study from Yaou, French Guiana

NASA Astrophysics Data System (ADS)

Girard, Jean-Pierre; Freyssinet, Philippe; Chazot, Gilles

2000-02-01

An integrated study of O and H isotopes in the lateritic profile of Yaou, French Guiana, was undertaken to investigate the usefulness of stable isotopes as tracers of climatic changes in continental environments. The studied profile is composed of a 27 m thick saprolite, mostly developed in the past under wet-and-dry tropical climate in association with a duricrust, overlain by a 3 m thick yellow latosol formed more recently under present equatorial hot and humid climate. δ 18O-δD values determined for weathering goethite (pseudomorphs after pyrite) and kaolinite (microcrystalline clay groundmass) throughout the 30 m deep profile reflect formation temperatures consistent with present (25°C) and realistic past climatic temperatures (20°C-30°C), indicating that weathering minerals formed in isotopic equilibrium with their genetic environment and were not subjected to significant isotope exchange after formation. A distinct shift downward (2‰ for δ 18O, 15‰ for δD) from low to high δ 18O-δD values occurs around 20 m depth in the saprolite. It is interpreted as recording the change from the past tropical to the present equatorial climate. Goethite and kaolinite in the 5-10 m thick saprolite interval immediately above the active basement weathering front are in isotopic equilibrium with modern water and must have formed under present equatorial-humid conditions. In contrast, goethite and kaolinite found higher up in the saprolite and in the duricrust formed in the past under tropical wet and dry climate from waters distinctly depleted in 18O and D relative to modern water. The marked depletion of paleo-meteoric water at Yaou most likely reflects a more contrasted or "monsoonal" character of the ancient tropical climate. The present study shows that ancient weathering minerals in lateritic profiles preserve their δ 18O-δD values and carry a time signal. The time signal is best expressed in minerals formed rapidly at the weathering front and not subjected to post-formational remobilization, such as the goethite pseudomorphs after pyrite occurring at Yaou. Groundmass kaolinite is more susceptible to partial remobilization, through successive dissolution-precipitation reactions, which may obliterate the paleoclimatic signal. Unraveling the climatic record carried by weathering minerals in old soil systems is greatly enhanced by studying both oxygen and hydrogen isotopic compositions.

KALMIOPSIS WILDERNESS, OREGON.

USGS Publications Warehouse

Page, Norman J; Miller, Michael S.

1984-01-01

Geologic, geochemical, geophysical field and laboratory, and mine and prospect studies conducted in the Kalmiopsis Wilderness, Oregon indicate that areas within and immediately adjacent to the wilderness have substantiated mineral-resource potential. The types of mineral resources which occur in these areas include massive sulfide deposits containing copper, zinc, lead, silver and gold; podiform chromite deposits; laterite deposits containing nickel, cobalt, and chromium; lode gold deposits; and placer gold deposits. Past production from existing mines is estimated to have been at least 7000 troy oz of gold, 4000 long tons of chromite, and few tens of tons of copper ore.

Elemental weathering fluxes and saprolite production rate in a Central African lateritic terrain (Nsimi, South Cameroon)

NASA Astrophysics Data System (ADS)

Braun, Jean-Jacques; Marechal, Jean-Christophe; Riotte, Jean; Boeglin, Jean-Loup; Bedimo Bedimo, Jean-Pierre; Ndam Ngoupayou, Jules Remy; Nyeck, Brunot; Robain, Henri; Sekhar, M.; Audry, Stéphane; Viers, Jérôme

2012-12-01

The comparison between contemporary and long-term weathering has been carried out in the Small Experimental Watershed (SEW) of Nsimi, South Cameroon in order to quantify the export fluxes of major and trace elements and the residence time of the lateritic weathering cover. We focus on the hillside system composed of a thick lateritic weathering cover topped by a soil layer. This study is built on the recent improvements of the hillside hydrological functioning and on the analyses of major and trace elements. The mass balance calculation at the weathering horizon scale performed with the parent rock as reference indicates (i) strong depletion profiles for alkalis (Na, K, Rb) and alkaline earths (Mg, Ca, Sr, Ba), (ii) moderate depletion profiles for Si, P, Cd, Cu, Zn, Ni and Co, (iii) depletion/enrichment profiles for Al, Ga, Ge, Sn, Pb, LREE, HREE, Y, U, Fe, V, Cr, Mn. It is noteworthy that (i) Mn and Ce are not significantly redistributed according to oxidative processes as it is the case for Fe, V and Cr, and (ii) Ge is fractionated compared to silica with enrichment in Fe-rich horizons. The calculations performed for the topsoil with iron crust as parent material reference reveal that the degradation of the iron crust is accompanied by the loss of most of the constituting elements, among which are those specifically accumulated as the redox sensitive elements (Fe, V, Cr) and iron oxide related elements like Th. The overall current elemental fluxes from the hillside system at the springs and the seepage zones are extremely low due to the inert lateritic mineralogy. Ninety-four percent of the whole Na flux generated from the hillside corrected from atmospheric deposits (77 mol/ha/yr) represents the current weathering rates of plagioclase (oligoclase) in the system, the other remaining 6% may be attributed to the dissolution of hornblende. The silica hillside flux is 300 mol/ha/yr and can be mostly attributed to the plagioclase and kaolinite dissolution. Al and Ga are exported from the lateritic regolith and maybe due to the dissolution of kaolinite crystals. Compared to the other immobile elements (Zr, Hf, Nb and Th), Ti is significantly exported. Among redox-sensitive elements (Fe, V, Cr, Mn, Ce), only Ce and Mn are exported out of the hillside system. The other elements (Fe, V, Cr) are likely able to be mobilized but over a short distance only. Rb, Sr, Ba, Ni, Cu, Zn are affected by export processes. LREE and Y are exported but in very low amounts (in the range from μmol/ha/yr to mmol/ha/yr) while HREE and U are exported in negligible quantities. A first attempt is carried out to compare the mature ridge top profile from Nsimi SEW with the immature ridge top weathering profile from the Mule Hole SEW (South India), developed on similar granodioritic basement, in order to get deeper insight into (i) the contemporary saprolite production rates and (ii) the combined effect of precipitation (in terms of Mean Annual Rainfall, MAR) and evapotranspiration on the aggressiveness of the draining solutions. Considering (i) the contemporary Na flux as representative of the dissolution of plagioclase crystals and conservative during saprolitization processes and (ii) steady state of the inter-annual recharge (R) over a 10 years period, the current saprolite production rates (σr) are of 22 mm/kyr for Mule Hole SEW and 2 mm/kyr for Nsimi SEW, respectively. Even with a very low R/MAR ratio (0.04) compared to Nsimi, the chemical weathering at Mule Hole is active and related to the groundwater exports. At Mule Hole, plagioclase crystals are still present in the saprolite and the soil cover leading to a diffuse weathering front. The high Nsimi R/MAR ratio (0.2) allows the solution to be still aggressive with respect to the plagioclase and other weatherable minerals at the bedrock interface resulting in their complete breakdown in a few centimetres (sharp weathering front) leading to a mature saprolite. For the Nsimi SEW, if we consider (i) the low contemporary saprolite production rate (2 mm/kyr), (ii) the Miocene age (average 15 Myr) of the South Cameron Plateau landscape and (ii) the limited movement of Africa continent since Eocene, the long term saprolite production rate should have remained in its lower range, from 2 to 10 m/Myr. This suggests that, for thick weathering profiles the migration of the weathering front into the bedrock occurs at a relatively uniform rate regardless of present-day climatic conditions. Climate variation leading to the alternation of setup of savanna or humid forest will have an effect on physical erosion rather than chemical erosion for such deep weathering profiles.

A study to investigate fluoride contamination and fluoride exposure dose assessment in lateritic zones of West Bengal, India.

PubMed

Samal, Alok C; Bhattacharya, Piyal; Mallick, Anusaya; Ali, Md Motakabber; Pyne, Jagadish; Santra, Subhas C

2015-04-01

To assess the status of severity of fluoride contamination in lateritic Bankura and Purulia districts of West Bengal, concentrations of fluoride in different water sources and agricultural field soils were investigated. The fluoride content (mg/l) was observed to differ with aquifer depths: 0.19-0.47 in dug wells, 0.01-0.17 in shallow tube wells, and 0.07-1.6 in deep tube wells. Fluoride within the World Health Organization (WHO) prescribed range (1.0-1.5 mg/l) was estimated only in ~17% of the total collected water samples while ~67% showed <0.7 mg/l fluoride and thus may impede in the production and maintenance of healthy teeth and bones of the residents, especially children. Fluoride in water was found to be significantly correlated (r = 0.63) with pH. The exposure dose of fluoride (mg/kg/day) from drinking water in infants, children, and adults was estimated in the ranges 0.02-0.53, 0.01-0.24, and 0.01-0.14, respectively against the standard value of 0.05. A clear risk of dental fluorosis is apparent in infants and children of the study area. The fluoride in soil (55-399 mg/kg) was detected to be significantly correlated with the fluoride content in deep tube wells and soil pH (r = 0.56 and 0.71, respectively). The relationships of soil fluoride with total hardness and that with phosphate were not significant. There is a high possibility of bioaccumulation of fluoride from contaminated soil and water of the study area to cultivated crops. This will enhance the quantity of fluoride intake into human food chain in addition to drinking water pathway.

Phosphorus runoff from sewage sludge applied to different slopes of lateritic soil.

PubMed

Chen, Yan Hui; Wang, Ming Kuang; Wang, Guo; Chen, Ming Hua; Luo, Dan; Ding, Feng Hua; Li, Rong

2011-01-01

Sewage sludge (SS) applied to sloping fields at rates that exceed annual forest nutrient requirements can be a source of phosphorus (P) in runoff. This study investigates the effects of different slopes (18, 27, 36, and 45%) on P in runoff from plots amended with SS (120 Mg ha). Lateritic soil (pH 5.2) was exposed to five simulated rainfalls (90 mm h) on outdoor plots. When sludge was broadcast and mixed with surface soils, the concentrations and loss in runoff of total P in the mixed sample (MTP), total P in the settled sample (STP), total particulate P (TPP), total suspended P (TSP), and total dissolved P (TDP) were highest at 1 or 18 d after application. Initially, pollution risks to surface waters generally increased to different degrees with steeper slopes, and then diminished gradually with dwindling differences between the slopes. The runoff losses coefficient of MTP increased in the order 36 > 45 > 27 > 18%. The initial event (1 and 18 d) accounted for 67.0 to 83.6% of total runoff P losses. Particulate fraction were dominant carriers for P losses, while with the lower slopes there was higher content of P per unit particulate fraction in runoff. Phosphorus losses were greatly affected by the interaction of sludge-soil-runoff and the modification of soil properties induced by sludge amendment. It is recommended to choose lower slopes (<27%) to reduce risk of P losses. Thus, the risk of application sludge to sloping fields in acid soils should be studied further in the field under a wider diversity of conditions. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Relief inversion in the geomorphological evolution of sub-Saharan West Africa

NASA Astrophysics Data System (ADS)

Butt, C. R. M.; Bristow, A. P. J.

2013-03-01

The geomorphology of much of sub-Saharan West Africa is dominated by the presence of plateaux and plains with ferruginous and, locally, aluminous (bauxitic) duricrusts. The plateaux occur at different elevations and have been correlated as two or more palaeosurfaces across much of the region. The duricrusts have generally been considered to be residual, formed by conformable erosion and chemical wasting of immediately underlying bedrock. This concept has been central to interpretations as diverse as the formation and evolution of the landscape and the development of geochemical exploration models. Recent regolith landform mapping, field observations and experience from mineral exploration in southern Mali and Burkina Faso, however, demonstrate that the duricrusts are mainly ferricretes, i.e., Fe oxide-cemented sediments. These observations require a re-interpretation of the geomorphological evolution of the region during the Cenozoic. The landscape has evolved by several cycles of weathering and erosion-deposition, triggered by climatic, tectonic or other environmental changes. It is proposed that an initial bauxitic/lateritic regolith was partly eroded following uplift and/or a change to a more arid climate, and that the detritus, rather than being removed, was deposited on slopes and valleys. During a subsequent humid period of lateritic weathering, Fe oxide cementation of this detritus formed ferricrete. Dehydration and hardening of the ferricrete after further uplift or aridity increased its resistance to erosion, resulting in relief inversion, with the detritus, in turn, being deposited downslope. This too has been weathered and cemented, to form a younger ferricrete. The occurrence of ferricrete landforms in adjacent countries, noted by field observation and inferred from satellite imagery, demonstrates that relief inversion is a very widespread and important phenomenon in southern Mali, Burkina Faso and adjacent countries in semi-arid West Africa.

U-Pb zircon geochronologycal investigation on the Morro dos Seis Lagos Carbonatite Complex and associated Nb deposit (Amazonas, Brazil)

NASA Astrophysics Data System (ADS)

Rossoni, Marco B.; Bastos Neto, Artur C.; Souza, Valmir S.; Marques, Juliana C.; Dantas, Elton; Botelho, Nilson F.; Giovannini, Arthur L.; Pereira, Vitor P.

2017-12-01

We present results of U-Pb dating (by MC-ICP-MS) of zircons from samples that cover all of the known lithotypes in the Seis Lagos Carbonatite Complex and associated lateritic mineralization (the Morro dos Seis Lagos Nb deposit). The host rock (gneiss) yielded an age of 1828 ± 09 Ma interpreted as the crystallization time of this unit. The altered feldspar vein in the same gneiss yielded an age of 1839 ± 29 Ma. Carbonatite samples provided 3 groups of ages. The first group comprises inherited zircons with ages compatible with the gneissic host rock: 1819 ± 10 Ma (superior intercept), 1826 ± 5 Ma (concordant age), and 1812 ± 27 Ma (superior intercept), all from the Orosirian. The second and the third group of ages are from the same carbonatite sample: the superior intercept age of 1525 ± 21 Ma (MSWD = 0.77) and the superior intercept age of 1328 ± 58 Ma (MSWD = 1.4). The mineralogical study indicates that the ∼1.3 Ga zircons have affinity with carbonatite. It is, however, a tendence rather than a well-defined result. The data allow state that the age of 1328 ± 58 Ma represents the maximum age of the carbonatite. Without the same certainty, we consider that the data suggest that this age may be the carbonatite age, whose emplacement would have been related to the evolution of the K'Mudku belt. The best age obtained in laterite samples (a superior intercept age of 1828 ± 12 Ma) is considered the age of the main source for the inherited zircons related to the gneissic host rock.

Micro-habitat distribution drives patch quality for sub-tropical rocky plateau amphibians in the northern Western Ghats, India

PubMed Central

Kulkarni, Siddharth; Watve, Aparna; Gaitonde, Nikhil; Pryce, David; Davies, Lewis; Bilton, David T.; Knight, Mairi E.

2018-01-01

The importance of patch quality for amphibians is frequently overlooked in distribution models. Here we demonstrate that it is highly important for the persistence of endemic and endangered amphibians found in the threatened and fragile ecosystems that are the rocky plateaus in Western Maharashtra, India. These plateaus are ferricretes of laterite and characterise the northern section of the Western Ghats/Sri Lanka Biodiversity Hotspot, the eighth most important global hotspot and one of the three most threatened by population growth. We present statistically supported habitat associations for endangered and data-deficient Indian amphibians, demonstrating significant relationships between individual species and their microhabitats. Data were collected during early monsoon across two seasons. Twenty-one amphibian taxa were identified from 14 lateritic plateaus between 67 and 1179m above sea level. Twelve of the study taxa had significant associations with microhabitats using a stepwise analysis of the AICc subroutine (distLM, Primer-e, v7). Generalist taxa were associated with increased numbers of microhabitat types. Non-significant associations are reported for the remaining 9 taxa. Microhabitat distribution was spatially structured and driven by climate and human activity. Woody plants were associated with 44% of high-elevation taxa. Of the 8 low-elevation taxa 63% related to water bodies and 60% of those were associated with pools. Rock size and abundance were important for 33% of high elevation specialists. Three of the 4 caecilians were associated with rocks in addition to soil and stream presence. We conclude the plateaus are individualistic patches whose habitat quality is defined by their microhabitats within climatic zones. PMID:29579111

[Effects of slopes on nitrogen transport along with runoff from sloping plots on a lateritic red soil amended with sewage sludge].

PubMed

Chen, Yan-Hui; Chen, Ming-Hua; Wang, Guo; Chen, Wen-Xiang; Yang, Shun-Cheng; Chai, Peng

2010-10-01

The effects of different slopes on nitrogen transport along with runoff from sloping plots amended with sewage sludge on a lateritic red soil were studied under simulated rainfall conditions. When the sludge was broadcasted and mixed with surface soils (BM), the MTN (total nitrogen of mixing sample), STN (total nitrogen of settled sample), TPN (total particulate nitrogen), TSN (total suspended nitrogen), TDN (total dissolved nitrogen) and NH4(+) -N concentrations and nitrogen loss amounts in runoff of all treatments were highest at 1 day or 18 days after application. The highest concentrations and the loss amounts of MTN and STN in the slope runoff for the BM treatment increased with slope degree, showing increasing pollution risks to the surface waters. The STN concentration and loss amounts from the 25 degrees plots were 126.1 mg x L(-1) and 1788.6 mg x m(-2), respectively, being 4.6 times and 5.8 times of the corresponding values from the 10 degrees plots, respectively. Then the concentrations and the loss amounts of nitrogen (except NO3(-) -N) from the BM plots diminished rapidly first and then tended to be stable with dwindling differences between the slopes. The loss of MTN and STN in early runoff (1 day and 18 days) accounted for 68.6% -73.4% and 62.3% -66.7% of the cumulative loss amounts during the experimental period for all the broadcasted treatments. Runoff loss coefficients of MTN increased in the order of 20 degrees > 25 degrees > 15 degrees > 10 degrees. Nitrogen was largely lost in dissolved species while large portion of NH4(+) -N was lost with particulates.

Mineralogy, geochemistry, and palynology of modern and late Tertiary mangrove deposits in the Barreiras Formation of Mosqueiro Island, northeastern Pará state, eastern Amazonia

NASA Astrophysics Data System (ADS)

Behling, Hermann; da Costa, Marcondes Lima

2004-12-01

A coastal environment has been interpreted from 110 cm thick mudstone deposits found at the base of a 10 m immature laterite profile, which forms the modern coastal cliff on Mosqueiro Island in northeastern Pará state, northern Brazil. The late Tertiary sediment deposits of the Barreiras Formation are studied by multi-element geochemistry and pollen analyses. The mineralogical and geochemical results show that the gray, organic-rich deposits are composed of kaolinite, quartz, and illite/muscovite, as well as pyrite and anatase. They are rich in SiO 2, Al 2O 3, and some FeO. The composition is homogenous, indicating that the detritus source area is formed of lateritic soils derived from acid rock composition. Their chemical composition, including trace elements, is somewhat comparable to continental shale, and the values are below the upper continental Earth crust composition. The pollen analytical data document that the mudstone deposits were formed by an ancient mangrove ecosystem. Mineralogical, geochemical, and pollen analytical data obtained from late Tertiary mangrove deposits are compared with modern mangrove deposits from the Bragança Peninsula of the northeastern coast of Pará state. Although the pollen composition of the deposits is very similar to the modern one, the geochemical and mineralogical composition is different. Smectite was only found in the modern deposit; illite/mica occurs in the ancient deposit, along with Mg, K, and Na. The pollen signature and detrital minerals (kaolinite, quartz and anatase) found in both mangrove deposits show that during the Miocene, a humid tropical climate condition prevailed, similar to modern conditions.

Mineral resource of the month: Chromium

USGS Publications Warehouse

Schulte, Ruth

2018-01-01

Although chromium is a metal, it does not occur naturally in metallic form. Chromium can be found in many minerals, but the only economically significant chromium-bearing mineral is chromite. Chromite has been mined from four different deposit types: stratiform chromite, podiform chromite, placer chromite, and laterite deposits. Most of the world's resources, however, are located in stratiform chromite deposits, such as the Bushveld Complex in South Africa. The economic potential of chromite resources depends on the thickness and continuity of the deposit and on the grade of the ore. Many of the major stratiform chromite deposits also contain economic levels of platinum, paladium, rhodium, osmium, iridium, and ruthenium.

Iron-tolerant Cyanobacteria as a Tool to Study Terrestrial and Extraterrestrial Iron Deposition

NASA Technical Reports Server (NTRS)

Brown, I. I.; Mummey, D.; Cooksey, K. E.; McKay, D. S.

2005-01-01

We are investigating biological mechanisms of terrestrial iron deposition as analogs for Martian hematite recently confirmed by. Possible terrestrial analogs include iron oxide hydrothermal deposits, rock varnish, iron-rich laterites, ferricrete soils, moki balls, and banded iron formations (BIFs). With the discovery of recent volcanic activity in the summit craters of five Martian volcanoes, renewed interest in the iron dynamics of terrestrial hydrothermal environments and associated microorganisms is warranted. In this study we describe a new genus and species of CB exhibiting elevated dissolved iron tolerance and the ability to precipitate hematite on the surface of their exopolymeric sheathes.

A Study on L-Asparaginase of Nocardia levis MK-VL_113

PubMed Central

Kavitha, Alapati; Vijayalakshmi, Muvva

2012-01-01

An enzyme-based drug, L-asparaginase, was produced by Nocardia levis MK-VL_113 isolated from laterite soils of Guntur region. Cultural parameters affecting the production of L-asparaginase by the strain were optimized. Maximal yields of L-asparaginase were recorded from 3-day-old culture grown in modified asparagine-glycerol salts broth with initial pH 7.0 at temperature 30°C. Glycerol (2%) and yeast extract (1.5%) served as good carbon and nitrogen sources for L-asparaginase production, respectively. Cell-disrupting agents like EDTA slightly enhanced the productivity of L-asparaginase. Ours is the first paper on the production of L-asparaginase by N. levis. PMID:22619604

A study on L-asparaginase of Nocardia levis MK-VL_113.

PubMed

Kavitha, Alapati; Vijayalakshmi, Muvva

2012-01-01

An enzyme-based drug, L-asparaginase, was produced by Nocardia levis MK-VL_113 isolated from laterite soils of Guntur region. Cultural parameters affecting the production of L-asparaginase by the strain were optimized. Maximal yields of L-asparaginase were recorded from 3-day-old culture grown in modified asparagine-glycerol salts broth with initial pH 7.0 at temperature 30°C. Glycerol (2%) and yeast extract (1.5%) served as good carbon and nitrogen sources for L-asparaginase production, respectively. Cell-disrupting agents like EDTA slightly enhanced the productivity of L-asparaginase. Ours is the first paper on the production of L-asparaginase by N. levis.

Environmental drivers of soil microbial community structure and function at the Avon River Critical Zone Observatory.

PubMed

Gleeson, Deirdre; Mathes, Falko; Farrell, Mark; Leopold, Matthias

2016-11-15

The Critical Zone is defined as the thin, permeable layer from the tops of the trees to the bottom of the bedrock that sustains terrestrial life on Earth. The geometry and shape of the various weathering zones are known as the critical zone architecture. At the centre of the Critical Zone are soils and the microorganisms that inhabit them. In Western Australia, the million-year-old stable weathering history and more recent lateral erosion during the past hundreds of thousands of years have created a geomorphic setting where deep weathering zones are now exposed on the surface along the flanks of many lateritic hills. These old weathering zones provide diverse physical and chemical properties that influence near surface pedologic conditions and thus likely shape current surface microbiology. Here, we present data derived from a small lateritic hill on the UWA Farm Ridgefield. Spatial soil sampling revealed the contrasting distribution patterns of simple soil parameters such as pH (CaCl2) and electric conductivity. These are clearly linked with underlying changes of the critical zone architecture and show a strong contrast with low values of pH3.3 at the top of the hill to pH5.3 at the bottom. These parameters were identified as major drivers of microbial spatial variability in terms of bacterial and archaeal community composition but not abundance. In addition, we used sensitive (14)C labelling to assess turnover of three model organic nitrogen compounds - an important biogeochemical functional trait relating to nutrient availability. Though generally rapid and in the order of rates reported elsewhere (t½<5h), some points in the sampling area showed greatly reduced turnover rates (t½>10h). In conclusion, we have shown that the weathering and erosion history of ancient Western Australia affects the surface pedology and has consequences for microbial community structure and function. Copyright © 2016 Elsevier B.V. All rights reserved.

Neogene weathering and terrestrial sedimentation in southern New Caledonia; inference on post-obduction tectonics and climate change

NASA Astrophysics Data System (ADS)

Folcher, Nicolas; Ricordel-Prognon, Caroline; Sevin, Brice; Maurizot, Pierre; Cluzel, Dominique; Quesnel, Florence

2014-05-01

Iron-rich sediments that fill up karst-like depressions and paleo-valleys in southern New Caledonia are mainly composed of re-sedimented laterite and saprolite. These fluvial sediments come from the erosion of an older regolith that developed upon peridotites and gabbros of the Peridotite Nappe during Late Oligocene times. At the bottom, conglomeratic facies fill incised valleys and contain some metre-size cobbles of ferricrete that record dissection of pre-existing weathering profiles and were deposited in alluvial fan environment. The basal conglomerate is overlain by sand, then dominantly silty fluvial sediments 40 to 50 m thick, with a few thin conglomerate channels. Brutal grain size reduction suggests that erosion was short-lived and followed by quiescence. Multiple interbedded ferruginous duricrusts and rhizocretions made of goethite (and secondary hematite) and liesegang rings reveal iron mobility and several iron oxi-hydroxides concretion/ cementation episodes alternating with sedimentation, probably as a consequence of water table variations. The top of the succession is overlain by a weathering profile and capped by a nodular lateritic ferricrete. Finally, reactivated erosion profoundly incised the fluvial succession and locally reached the bedrock which today crops out upstream along the main river beds. In southern New Caledonia some ferricretes and ferruginous duricrusts have been dated at -25 Ma and -20 to -10 Ma by paleomagnetic method (in progress). They could be correlated to some warming events of the Late Oligocene and Early Miocene or to the Middle Miocene Climatic Optimum. Erosion that predates the accumulation of terrestrial sediments may be tentatively correlated to the uplift that accompanied the emplacement of the Saint-Louis and Koum plutons, and some internal dissection episodes could be related to the Lower Miocene post-obduction slab break off. The final erosion is most probably related to the southward tilt of New Caledonia due to Recent SW Pacific tectonics and to sea level drops during the Quaternary as well.

Storm event-scale nutrient attenuation in constructed wetlands experiencing a Mediterranean climate: A comparison of a surface flow and hybrid surface-subsurface flow system.

PubMed

Adyel, Tanveer M; Oldham, Carolyn E; Hipsey, Matthew R

2017-11-15

Among different Water Sensitive Urban Design options, constructed wetlands (CWs) are used to protect and restore downstream water quality by attenuating nutrients generated by stormwater runoff. This research compared the nutrient attenuation ability during a diverse population of storm events of two CWs: (a) a hybrid CW with multiple alternating surface flow (SF) and laterite-based subsurface flow (SSF) compartments, and (b) a single stage SF CW. Within-storm variability, nutrient concentrations were assessed at 2 to 3-h intervals at both the main inlet and outlet of each CW. Dissolved oxygen concentrations of the surface waters were also monitored at 10-min intervals using high frequency in situ sensors. Nutrient loads into the CWs were observed to be higher when a high rainfall event occurred, particularly after longer antecedent dry conditions. Longer hydraulic retention times promoted higher attenuation at both sites. However, the relative extent of nutrient attenuation differed between the CW types; the mean total nitrogen (TN) attenuation in the hybrid and SF CW was 45 and 48%, respectively. The hybrid CW attenuated 67% total phosphorus (TP) loads on average, while the SF CW acted as a net TP source. Periodic storm events transitioned the lentic CW into a lotic CW and caused riparian zone saturation; it was therefore hypothesized that such saturation of organic matter rich-riparian zones led to release of TP in the system. The hybrid CW attenuated the released TP in the downstream laterite-based SSF compartments. Diel oxygen metabolism calculated before and after the storm events was found to be strongly correlated with water temperature, solar exposure and antecedent dry condition during the pre-storm conditions. Furthermore, the SF CW showed a significant relationship between overall nutrient load attenuation and the change in oxygen metabolism during the storm perturbation, suggesting oxygen variation could be a useful proxy indicator of CW function. Copyright © 2017 Elsevier B.V. All rights reserved.

Origin and significance of high nickel and chromium concentrations in pliocene lignite of the Kosovo Basin, Serbia

USGS Publications Warehouse

Ruppert, L.; Finkelman, R.; Boti, E.; Milosavljevic, M.; Tewalt, S.; Simon, N.; Dulong, F.

1996-01-01

Trace element data from 59 Pliocene lignite cores from the lignite field in the Kosovo Basin, southern Serbia, show localized enrichment of Ni and Cr (33-304 ppm and 8-176 ppm, respectively, whole-coal basis). Concentrations of both elements decrease from the western and southern boundaries of the lignite field. Low-temperature ash and polished coal pellets of selected bench and whole-coal samples were analyzed by X-ray diffraction and scanning electron microscopy with energy-dispersive X-ray analyses. These analyses show that most of the Ni and Cr are incorporated in detrital and, to a lesser degree, in authigenic minerals. The Ni- and Cr-bearing detrital minerals include oxides, chromites, serpentine-group minerals and rare mixed-layer clays. Possible authigenic minerals include Ni-Fe sulfates and sulfides. Analyses of three lignite samples by a supercritical fluid extraction technique indicate that some (1-11%) of the Ni is organically bound. Ni- and Cr-bearing oxides, mixed-layer clays, chromites and serpentine-group minerals were also identified in weathered and fresh samples of laterite developed on serpentinized Paleozoic peridotite at the nearby Glavica and C??ikatovo Ni mines. These mines are located along the western and northwestern rim, respectively, of the Kosovo Basin, where Ni contents are highest. The detrital Ni- and Cr-bearing minerals identified in lignite samples from the western part of the Kosovo Basin may have been transported into the paleoswamp by rivers that drained the two Paleocene laterites. Some Ni may have been transported directly into the paleoswamp in solution or, alternatively, Ni may have been leached from detrital minerals by acidic peat water and adsorbed onto organic matter and included into authigenic mineral phases. No minable source of Ni and Cr is known in the southern part of the lignite field; however, the mineral and chemical data from the lignite and associated rocks suggest that such a source area may exist.

Slope Stability Analysis for Shallow Landslides using TRIGRS: A Case Study for Sta. Cruz, Zambales, Philippines

NASA Astrophysics Data System (ADS)

Mendoza, J. P. A.

2016-12-01

The Philippines, being located in the circum-Pacific, bounded by multiple subduction zones, open seas and ocean, is one of the most hazard-prone countries in the world (Benson, 1997). This widespread recurrence of natural hazards in the country requires much attention for disaster management (Aurelio, 2006). On the average, 21 typhoons enter the Philippine area of responsibility annually with 6-9 making a landfall. Several rainfall-induced landslide events are reported annually particularly during and after the inundation of major typhoons which imposes hazards to communities and causes destruction of properties due to the moving mass and possible flash floods it may induce. Shallow landslides are the most commonly observed failure involving soil-mantled slopes and are considered major geohazards, often causing property damage and other economic loss. Hence numerous studies on landslide susceptibility including numerical models based on infinite slope equation are used in order to identify slopes prone to occurrences of shallow landslides. The study aims to determine the relationships between the slope and elevation to the factor of safety for laterite-mantled topography by incorporating precipitation values in the determination of landslide susceptibility. Using a DEM, flow direction map and slope map of the Sta Cruz (Zambales, Philippines), the FORTRAN based program TRIGRS, was used to generate the values for the factors of safety in the study area. Overlays with a generated slope map and elevation map were used to determine relationships of the mentioned factors and the factors of safety. A slope in a topography mantled with lateritic soil will fail at a slope angle higher than 20 degrees. Generally, the factor of safety decreases as the slope angle increases; this increases the probability and risk of slope failure. Elevation has no bearing on the computation for the factor of safety. The factor of safety is heavily dependent on the slope angle. The value of generated factor of safety coincides with the published geohazard map from Mines and Geosciences Bureau(MGB).

Lake Eyre, Simpson Desert, South Australia, Australia

NASA Image and Video Library

1990-12-10

STS035-501-007 (2-10 Dec. 1990) --- The STS-35 crewmembers aboard the Earth-orbiting Space Shuttle Columbia photographed this view of the Arid Simpson Desert of Australia with a handheld Rolleiflex camera. Lake Eyre is normally dry; however, the STS-35 crew was able to recognize water in the lowest parts of the lake (dark pink area) and possibly in Lake Blanche east of Lake Eyre. Lake Frome lies in the distance separated from Lake Torrens (top right) by dark hills of Flinders Range. The Finke River (bottom left to middle) flows into the Eyre basin from the northwest. Although it is the largest river entering the basin, Finke's floods seldom reach Lake Eyre. The dark brown patch in the foreground is an area of ancient, brown lateritic soils partly covered by dunes.

Deficiencies and toxicities of trace elements and micronutrients in tropical soils: Limitations of knowledge and future research needs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davies, B.E.

1997-01-01

This article reviews present knowledge concerning deficiencies and toxicities of trace elements and micronutrients in tropical soils. The myth that all tropical soils are highly leached and nutrient-poor is challenged. Continuing use of the term laterite by ecologists and geologists is criticized and adoption of plinthite is urged. The trace element content of plinthite and its possible influence on micronutrient availability are described. Micronutrient limitations of tropical agriculture are related to soil type and formation, and the special problem of aluminum toxicity in acid soils is discussed in both agricultural and ecological contexts. Studies of micronutrient cycling in tropical forestsmore » or savannas are needed to supplement the emerging picture of the complexities of major element cycles in these ecosystems.« less

Observations of the plant growth and annual flooding in the inland delta of the Niger River, west Africa

NASA Technical Reports Server (NTRS)

Macleod, N. H. (Principal Investigator)

1973-01-01

The author has identified the following significant results. A large potential irrigation area with water delivery system in place was identified from ERTS-1 imagery. The site is in the Sahara Desert. Color additive change detection imagery was used to assess ground water potentials in the Savannah in conjunction with a major US AID-Mali livestock sector initiative. The potential capacity to map laterite deposits in the Inland Delta from space was established with the help of aerial and ground surveys. A color composite of the Inland Delta could have saved French biogeographers 3 5/6 man-years of professional field work had it been available, according to the man who prepared a plant community map of part of the southern Inland Delta.

Characterization of the Sukinda and Nausahi ultramafic complexes, Orissa, India by platinum-group element geochemistry

USGS Publications Warehouse

Page, N.J.; Banerji, P.K.; Haffty, J.

1985-01-01

Samples of 20 chromitite, 14 ultramafic and mafic rock, and 9 laterite and soil samples from the Precambrian Sukinda and Nausahi ultramafic complexes, Orissa, India were analyzed for platinum-group elements (PGE). The maximum concentrations are: palladium, 13 parts per billion (ppb); platinum, 120 ppb; rhodium, 21 ppb; iridium, 210 ppb; and ruthenium, 630 ppb. Comparison of chondrite-normalized ratios of PGE for the chromitite samples of lower Proterozoic to Archean age with similar data from Paleozoic and Mesozoic ophiolite complexes strongly implies that these complexes represent Precambrian analogs of ophiolite complexes. This finding is consistent with the geology and petrology of the Indian complexes and suggests that plate-tectonic and ocean basin developement models probably apply to some parts of Precambrian shield areas. ?? 1985.

Geology and mineral resources of central Antioquia Department (Zone IIA), Colombia

USGS Publications Warehouse

Hall, R.B.; Alvarez A., Jairo; Rico H., Hector

1973-01-01

This report summarizes the geology of an area of some 6000 square kilometers in the northern part of the Central Cordillera of the Colombian Andes. The area, in north-central Department of Antioquia, was mapped between 1964 and 1968 as part of the Inventario Minero Nacional (IMN) project. Mineral resources are summarized within a larger area, designated as subzone ILK of IMN Zone If, which comprises almost 22,000 sq. kin, including the area mapped geologically by IMN and additional areas mapped by other agencies. The oldest formation is a micaceous paragneiss of early Paleozoic or possibly late Precambrian age. A thick geosynclinal sedimentary series accumulated during the Paleozoic Era and became regionally metamorphosed to greenschist (locally amphibolite) facies during the Permian or early Triassic; these schists and gneisses are designated collectively as the Valdivia Group. The Permian(?) orogenic episode included intrusion of concordant syntectonic plutons, mostly of tonalitic composition. Rocks of unequivocal Triassic or Jurassic age are not recognized. The Cretaceous is well represented by both igneous and sedimentary assemblages. Eugeosynclinal alpine ophiolites comprising submarine basalt flows and numerous intrusions of gabbro and serpentinite are prominent in the Lower Cretaceous, together with flysch composed of marine shale and lesser sandstone and conglomerate. The Upper Cretaceous is represented along the west border of the mapped area by submarine basalt flows and pyroclastic rocks, locally Interbedded with fine-grained clastic sedimentary beds, and lenses of dark laminated chert, at least part of which is radiolarian. The Late Cretaceous was marked by an orogenic event that profoundly folded and faulted all rocks and in the Central Cordillera caused low-grade metamorphism, the overprint of which is hardly observable in pre-Cretaceous rocks elsewhere. The Late Cretaceous orogeny culminated with discordant intrusion of the epizonal tonalitic Antioquian batholith. Displacement along the great Romeral wrench fault may have begun in the Cretaceous. Plutonism continued into the Cenozoic, exemplified by the hornblende-diorite Sabanalarga pluton. Intermontane basins were filled with molasse derived from the erosion of adjacent highlands; Tertiary sedimentation in marshy areas included organic carboniferous matter subsequently converted to lignite or subbituminous coal. The Sabanalarga fault system originated in the Late Tertiary; intermittent displacement continued on the older wrench faults such as the Romeral. Epeirogenic uplift, which probably began in the Pliocene and continued through the Pleistocene and Holocene, brought on renewed erosion which has sculptured the mountains into their present form. Mineral resources in subzone IIA are varied but not of outstanding importance. Gold and silver mining, significant in past centuries, is minor today. Ferruginous laterite on serpentinite once considered as a potential source of iron ore is not economically exploitable. IMN has explored nickeliferous laterite at the extreme northwest corner of subzone IIA; this is a potential resource, exploitable only after exhaustion of the larger and richer nickel laterite deposit at Cerro Matoso, farther to the north and outside the boundaries of Zone If. Known deposits of mercury, chromium, manganese, and copper are small, with limited economic potential. Nonmetallic resources include raw materials for cement, including portland cement. Saprolite clay is widely used in making common red brick and tile, still a dominant construction material in all but the most modern multistory buildings. Aggregate materials are varied and abundant. Kaolin of good quality near La Union is important as a ceramic raw mineral filler. Tertiary subbituminous coal beds are an important energy resource in western subzone IIA, and have a good potential for greater development. Deposits of sodic feldspar, talc, decorative stone, and silica a

Stabilization of arsenic and fluoride bearing spent adsorbent in clay bricks: Preparation, characterization and leaching studies.

PubMed

Rathore, Vineet Kumar; Mondal, Prasenjit

2017-09-15

The presence of arsenic and fluoride in groundwater has been observed throughout the world. Many technologies have been developed by various research groups in order to tackle this problem. Adsorption has emerged as one of the best possible technique for the removal of arsenic, fluoride and many other pollutants from drinking water. Although a considerable amount of work has been published on the adsorptive removal of arsenic and fluoride, the area related to the management of spent adsorbent is not well explored. Present paper deals with the adsorptive removal of arsenic and fluoride from aqueous solution by three different types of adsorbents, namely, thermally treated laterite (TTL), acid-base treated laterite (ABTL) and aluminum oxide/hydroxide nanoparticles (AHNP). Under the experimental conditions in batch operation, the adsorption capacities of TTL, ABLT and AHNP for arsenic are found to be 6.43 μg/g, 9.25 μg/g and 48.5 μg/g respectively, whereas for fluoride, these values are found as 0.21 mg/g, 0.85 mg/g and 4.65 mg/g respectively. After adsorption, the spent adsorbents have been stabilized in the form of clay bricks. The effects of spent adsorbent concentration on the properties of bricks and their leaching properties are investigated. The bricks have been tested for various properties like density, percentage water absorption, shrinkage, compressive strength and efflorescence. The maximum values of density and shrinkage of the bricks formed are found as 2.3 g/cm 3 and 10.2%, whereas the percentage water absorption and compressive strength of the bricks are found between 11 and 14% and 35 to 150 kgf/cm 2 respectively. All the test results are in accordance with the criteria set by Indian Standards. The leaching test of arsenic and fluoride from the bricks reveals that their maximum values in leachate are 510 μg/L and 2.1 mg/L respectively, which are below the permissible limits of USEPA standards. Copyright © 2017 Elsevier Ltd. All rights reserved.

Soil water dynamics of lateritic catchments as affected by forest clearing for pasture

NASA Astrophysics Data System (ADS)

Sharma, M. L.; Barron, R. J. W.; Williamson, D. R.

1987-10-01

Aspects of soil water dynamics as affected by land use changes were examined over a period of five years (1974-1979) in two groups of adjacent catchments located in 1200 mm yr -1 and 800 mm yr -1 rainfall zones near Collie, Western Australia. In the summer of 1976/1977, after three years of calibration, 100% of one high rainfall catchment, Wights, and 53% of one lower rainfall catchment, Lemon, was cleared of native eucalyptus forest and replaced with pasture. The soil water storage down to 6m was measured in-situ using a neutron probe in fifteen access tubes located at five stratified sites in each catchment. Considerable spatial variability in soil water storage was encountered within a site, between sites within a catchment, and between paired catchments; the dominant variability being between sites. Comparisons between the pre- and postclearing states within a catchment and between the cleared and uncleared control catchments were used to evaluate the effect of change in land use on soil water dynamics. Within two years of the change from forest to pasture, a significant increase in soil water storage had occurred in the profiles in both cleared catchments. Concurrently, there was a small decrease in the uncleared control catchments. The increases following clearing were greater in the higher than in the lower rainfall catchment, more pronounced in the first year than in the second year, and occurred mostly at depths greater than 2m. In Wights catchment, the increase in summer minimum soil water storage in the first and second years amounted to 220 and 58 mm respectively, whilst for Lemon catchment the increase for the first year was < 50 mm. This increased soil water storage was due to a substantially lower evapotranspiration from the shallow-rooted, seasonally active pasture which extracts water from the top 1 m or so, compared with the perennial native eucalyptus forest which extracts water from depths down to 6 m and beyond. Due to the relatively low water holding capacity of the surface lateritic soils, the drainage beyond 1 m is substantially increased under pasture, and this results in an increased recharge to the underlying aquifer.

Organic complexation and translocation of ferric iron in podzols of the Negro River watershed. Separation of secondary Fe species from Al species

NASA Astrophysics Data System (ADS)

Fritsch, E.; Allard, Th.; Benedetti, M. F.; Bardy, M.; do Nascimento, N. R.; Li, Y.; Calas, G.

2009-04-01

The development of podzols in lateritic landscapes of the upper Amazon basin contributes to the exportation of organic carbon and associated metals in the black waters of the Negro River watershed. We have investigated the distribution of Fe III in the clay-size fraction of eight organic-rich horizons of waterlogged plateau podzols, to unravel the weathering conditions and mechanisms that control its transfer to the rivers. The speciation and amount of Fe III stored in residual mineral phases of laterites, or bound to organic compounds of weakly and well-expressed podzols, were determined by electron paramagnetic resonance spectroscopy combined with chemical analyses. Reducing conditions restrict the production of organo-Fe complexes in the subsoil B-horizons of waterlogged podzols and most of the Fe 2+ released from the dissolution of Fe-oxides is exported to the rivers via the perched groundwater. However, significant amounts of diluted Fe III bound to organic ligands (Fe IIIOM) and nano Fe-oxides are produced at the margin of the depression in the topsoil A horizons of weakly expressed podzols due to shorter periods of anoxia. The downward translocation of organically bound metals from topsoil A to subsoil B-horizons of podzols occurs in shorter distances for Fe than it does for Al. This separation of secondary Fe species from Al species is attributed to the physical fractionation of their organic carriers in texture contrasted B-horizons of podzols, as well as to the effect of pH on metal speciation in soil solutions and metal binding onto soil organic ligands (mostly for Al). This leads us to consider the topsoil A horizons of weakly expressed podzols, as well as the subsoil Bh horizon of better-expressed ones, as the main sources for the transfer of Fe IIIOM to the rivers. The concentration of Fe IIIOM rises from soil sources to river colloids, suggesting drastic biogeochemical changes in more oxygenated black waters of the Negro River watershed. The contribution of soil organic matter to the transfer of Fe to rivers is likely at the origin of the peculiar Fe isotope pattern recently recognized in podzolic environments.

Development of kenaf mat for slope stabilization

NASA Astrophysics Data System (ADS)

Ahmad, M. M.; Manaf, M. B. H. Ab; Zainol, N. Z.

2017-09-01

This study focusing on the ability of kenaf mat to act as reinforcement to laterite compared to the conventional geosynthetic in term of stabilizing the slope. Kenaf mat specimens studied in this paper are made up from natural kenaf fiber with 3mm thickness, 150mm length and 20mm width. With the same size of specimens, geosynthetic that obtain from the industry are being tested for both direct shear and tensile tests. Plasticity index of the soil sample used is equal to 13 which indicate that the soil is slightly plastic. Result shows that the friction angle of kenaf mat is higher compared to friction between soil particles itself. In term of resistance to tensile load, the tensile strength of kenaf mat is 0.033N/mm2 which is lower than the tensile strength of geosynthetic.

Near surface IP investigations: Four case studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hearst, R.B.; Morris, W.A.; Clark, M.A.

1995-12-31

The use of the Induced Polarisation (IP) method of geophysical surveying for near surface site investigations is gaining acceptance within the geophysical community. In this study the IP method is evaluated as a tool for the delineation of ground water resources; contamination plume detection in a lateritic horizon; and acid mine drainage leak detection from decommissioned mine tailings. A time domain IP system was selected for this study primarily for the flexibility in the selection and setting of receiver time windows and diagnostic characteristics attributed to submitting the data to Cole-Cole analysis. Analysis of the acquired data in conjunction withmore » available borehole and geological information illustrates the effectiveness and usefulness of the survey method for solving near surface problems. In all of the locations tested, it was found that with a properly designed IP survey it was possible to resolve the target and/or related structures.« less

Optimization and purification of L-asparaginase produced by Streptomyces tendae TK-VL_333.

PubMed

Kavitha, Alapati; Vijayalakshmi, Muvva

2010-01-01

Cultural factors affecting the production of L-asparaginase by Streptomyces tendae isolated from laterite soil samples of Guntur region were investigated on glycerol-asparagine-salts (modified ISP-5) broth. Optimal yields of L-asparaginase were recorded in the culture medium with the initial pH 7.0 incubated at 30 degrees C for 72 h. The strain utilized sucrose (2%) and yeast (2%) extract as carbon and nitrogen sources for L-asparaginase production. The productivity of L-asparaginase was slightly enhanced when the strain was treated with cell-disrupting agents like EDTA. The crude enzyme was purified to homogeneity by ammonium sulfate precipitation, Sephadex G-100 and CM-Sephadex G-50 gel filtration. By employing sodium dodecyl sulfate-polyacrylamide gel electrophoresis, the molecular weight of the enzyme was recorded as 97.4 kDa. This is the first report on production and purification of L-asparaginase from S. tendae.

Past and Present Weathering Recorded in Cretaceous Shale Samples from Colombia - Implications for Paleoenvironmental Reconstructions

NASA Astrophysics Data System (ADS)

Mahoney, C.; März, C.; Wagner, T.

2016-12-01

It is well known that for geochemical studies on ancient rocks, outcrop samples can be compromised by present-day weathering. This raises the fundamental question, if only outcrop samples are available, how reliable can paleoenvironmental reconstructions be? To answer this question, shale samples have been gathered from Cretaceous outcrops of the Eastern Cordillera of Colombia, and analysed by XRF and Fe speciation in order to investigate paleo-redox conditions in this margin basin of the Proto-Atlantic. The samples are consistently depleted (relative to average shale) in redox-related trace metals and in total Fe indicating oxic conditions, whereas Fe speciation (highly reactive over total Fe) indicates anoxic conditions. We ask if this depletion in trace metals and total Fe is due to a lack of primary supply from the depositional environment, or if is it caused by modern oxidative outcrop weathering in this tropical mountainous setting? Our results from artificial weathering experiments confirm that certain trace metals U, Zn and Mo are easily leached from the samples, whereas Fe is quantitatively retained in the samples due to conversion of pyrite and siderite to Fe oxides. Pristine samples from wells in the adjacent Middle Magdalena Valley Basin (MMV) also exhibit total Fe depletion, but are up to 2000-fold enriched in Mo. This combined evidence indicates that the depletion of trace metals may be due to contemporary weathering, but there has to be a paleoenvironmental reason behind the low total Fe signature. The Guiana Shield was the probable source of sediment to the Cretaceous basin. The Chemical Index of Alteration suggest the source of detrital material was initially highly weathered (average 83, maximum 95). Ancient laterites have been identified on the Guiana Shield, and retention of Fe in these laterites may explain the low Fe input into the Eastern Cordillera basin. These results confirm that trace metal-based redox proxies may be seriously affected by oxidative weathering in outcrops, and caution should be applied when using such samples. But it also appears that due to the extreme chemical weathering in the provenance area, the Eastern Cordillera basin (and adjacent MMV basin) was unusually Fe-depleted throughout the Cretaceous, and this geochemical signal is preserved even in weathered outcrop samples.

The application of U-isotopes to assess weathering in contrasted soil-water regime in Brazil.

PubMed

Rosolen, Vania; Bueno, Guilherme Taitson; Bonotto, Daniel Marcos

2018-02-01

This paper presents the use of U-series radionuclides 238 U and 234 U to evaluate the biogeochemical disequilibrium in soil cover under a contrasted soil-water regime. The approach was applied in three profiles located in distinct topographical positions, from upslope ferralitic to downslope hydromorphic domain. The U fractionation data was obtained in the samples representing the saprolite and the superficial and subsuperficial soil horizons. The results showed a significant and positive correlation between U and the Total Organic Carbon (TOC). Soil organic matter has accumulated in soil due to hydromorphy. There is no evidence of positive correlation between U and Fe, as expected in lateritic soils. The advance of the hydromorphy on Ferralsol changes the weathering rates, and the ages of weathering are discussed as a function of the advance of waterlogged soil conditions from downslope. Also, the bioturbation could represent the other factor responsible to construct a more recent soil horizon. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermal characteristic of limonite ore upon calcination and reduction

NASA Astrophysics Data System (ADS)

Febriana, Eni; Manaf, Azwar; Prasetyo, A. B.; Mayangsari, W.

2018-05-01

Thermal characteristics of the limonite laterite ore types have been studied using TG / DTA. There are four endothermic peaks at 250, 646, 900, and 1023 °C with a total mass loss of 10.07wt%. These four peaks correspond to the XRD results on samples calcined at 600-1000 °C. Analysis of TG / DTA to the mixture of limonite and graphite showed two endothermic reaction peaks at 641 and 900 °C and an exothermic peak at 1180 °C. Reduction of the limonite-graphite mixture was done by heating at 800-1100 °C for 1 hour, and the reduced samples were analyzed using XRD. The results indicate that the reduction process proceed completely at higher temperatures, indicated by the increasing intensity of kamacite and Fe metal phase, and the decrease of peak intensity of carbon due to reaction with metal oxides. At 1100 °C, intensity of Fe-metal decreased due to sintering of Fe which may occur because the temperature was too high.

Progress in bioleaching: part B: applications of microbial processes by the minerals industries.

PubMed

Brierley, Corale L; Brierley, James A

2013-09-01

This review presents developments and applications in bioleaching and mineral biooxidation since publication of a previous mini review in 2003 (Olson et al. Appl Microbiol Biotechnol 63:249-257, 2003). There have been discoveries of newly identified acidophilic microorganisms that have unique characteristics for effective bioleaching of sulfidic ores and concentrates. Progress has been made in understanding and developing bioleaching of copper from primary copper sulfide minerals, chalcopyrite, covellite, and enargite. These developments point to low oxidation-reduction potential in concert with thermophilic bacteria and archaea as a potential key to the leaching of these minerals. On the commercial front, heap bioleaching of nickel has been commissioned, and the mineral biooxidation pretreatment of sulfidic-refractory gold concentrates is increasingly used on a global scale to enhance precious metal recovery. New and larger stirred-tank reactors have been constructed since the 2003 review article. One biooxidation-heap process for pretreatment of sulfidic-refractory gold ores was also commercialized. A novel reductive approach to bioleaching nickel laterite minerals has been proposed.

Evaluation of Mercury Contamination in Fungi Boletus Species from Latosols, Lateritic Red Earths, and Red and Yellow Earths in the Circum-Pacific Mercuriferous Belt of Southwestern China.

PubMed

Falandysz, Jerzy; Zhang, Ji; Wang, Yuan-Zhong; Saba, Martyna; Krasińska, Grażyna; Wiejak, Anna; Li, Tao

2015-01-01

For the first time, highly elevated levels of mercury (Hg) have been documented for several species of the edible Fungi genus Boletus growing in latosols, lateritic red earths, and red and yellow earths from the Yunnan province of China. Analysis of Hg concentrations in the genus suggests that geogenic Hg is the dominant source of Hg in the fungi, whereas anthropogenic sources accumulate largely in the organic layer of the forest soil horizon. Among the 21 species studied from 32 locations across Yunnan and 2 places in Sichuan Province, the Hg was found at elevated level in all samples from Yunnan but not in the samples from Sichuan, which is located outside the mercuriferous belt. Particularly abundant in Hg were the caps of fruiting bodies of Boletus aereus (up to 13 mg kg-1 dry matter), Boletus bicolor (up to 5.5 mg kg-1 dry matter), Boletus edulis (up to 22 mg kg-1 dry matter), Boletus luridus (up to 11 mg kg-1 dry matter), Boletus magnificus (up to 13 mg kg-1 dry matter), Boletus obscureumbrinus (up to 9.4 mg kg-1 dry matter), Boletus purpureus (up to 16 mg kg-1 dry matter), Boletus sinicus (up to 6.8 mg kg-1 dry matter), Boletus speciosus (up to 4.9mg kg-1 dry matter), Boletus tomentipes (up to 13 mg kg-1 dry matter), and Boletus umbriniporus (up to 4.9 mg kg-1 dry matter). Soil samples of the 0-10 cm topsoil layer from the widely distributed locations had mercury levels ranging between 0.034 to 3.4 mg kg-1 dry matter. In Yunnan, both the soil parent rock and fruiting bodies of Boletus spp. were enriched in Hg, whereas the same species from Sichuan, located outside the mercuriferous belt, had low Hg concentrations, suggesting that the Hg in the Yunnan samples is mainly from geogenic sources rather than anthropogenic sources. However, the contribution of anthropogenically-derived Hg sequestered within soils of Yunnan has not been quantified, so more future research is required. Our results suggest that high rates of consumption of Boletus spp. from Yunnan can deliver relatively high doses of Hg to consumers, but that rates can differ widely because of large variability in mercury concentrations between species and locations.

Evaluation of Mercury Contamination in Fungi Boletus Species from Latosols, Lateritic Red Earths, and Red and Yellow Earths in the Circum-Pacific Mercuriferous Belt of Southwestern China

PubMed Central

Falandysz, Jerzy; Zhang, Ji; Wang, Yuan-Zhong; Saba, Martyna; Krasińska, Grażyna; Wiejak, Anna; Li, Tao

2015-01-01

For the first time, highly elevated levels of mercury (Hg) have been documented for several species of the edible Fungi genus Boletus growing in latosols, lateritic red earths, and red and yellow earths from the Yunnan province of China. Analysis of Hg concentrations in the genus suggests that geogenic Hg is the dominant source of Hg in the fungi, whereas anthropogenic sources accumulate largely in the organic layer of the forest soil horizon. Among the 21 species studied from 32 locations across Yunnan and 2 places in Sichuan Province, the Hg was found at elevated level in all samples from Yunnan but not in the samples from Sichuan, which is located outside the mercuriferous belt. Particularly abundant in Hg were the caps of fruiting bodies of Boletus aereus (up to 13 mg kg-1 dry matter), Boletus bicolor (up to 5.5 mg kg-1 dry matter), Boletus edulis (up to 22 mg kg-1 dry matter), Boletus luridus (up to 11 mg kg-1 dry matter), Boletus magnificus (up to 13 mg kg-1 dry matter), Boletus obscureumbrinus (up to 9.4 mg kg-1 dry matter), Boletus purpureus (up to 16 mg kg-1 dry matter), Boletus sinicus (up to 6.8 mg kg-1 dry matter), Boletus speciosus (up to 4.9mg kg-1 dry matter), Boletus tomentipes (up to 13 mg kg-1 dry matter), and Boletus umbriniporus (up to 4.9 mg kg-1 dry matter). Soil samples of the 0–10 cm topsoil layer from the widely distributed locations had mercury levels ranging between 0.034 to 3.4 mg kg-1 dry matter. In Yunnan, both the soil parent rock and fruiting bodies of Boletus spp. were enriched in Hg, whereas the same species from Sichuan, located outside the mercuriferous belt, had low Hg concentrations, suggesting that the Hg in the Yunnan samples is mainly from geogenic sources rather than anthropogenic sources. However, the contribution of anthropogenically-derived Hg sequestered within soils of Yunnan has not been quantified, so more future research is required. Our results suggest that high rates of consumption of Boletus spp. from Yunnan can deliver relatively high doses of Hg to consumers, but that rates can differ widely because of large variability in mercury concentrations between species and locations. PMID:26606425

Ni cycling in mangrove sediments from New Caledonia

NASA Astrophysics Data System (ADS)

Noël, Vincent; Morin, Guillaume; Juillot, Farid; Marchand, Cyril; Brest, Jessica; Bargar, John R.; Muñoz, Manuel; Marakovic, Grégory; Ardo, Sandy; Brown, Gordon E.

2015-11-01

Covering more than 70% of tropical and subtropical coastlines, mangrove intertidal forests are well known to accumulate potentially toxic trace metals in their sediments, and thus are generally considered to play a protective role in marine and lagoon ecosystems. However, the chemical forms of these trace metals in mangrove sediments are still not well known, even though their molecular-level speciation controls their long-term behavior. Here we report the vertical and lateral changes in the chemical forms of nickel, which accumulates massively in mangrove sediments downstream from lateritized ultramafic deposits from New Caledonia, where one of nature's largest accumulations of nickel occurs. To accomplish this we used Ni K-edge Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy data in combination with microscale chemical analyses using Scanning Electron Microscopy coupled with Energy-Dispersive X-ray Spectroscopy (SEM-EDXS). After Principal Component and Target Transform analyses (PCA-TT), the EXAFS data of the mangrove sediments were reliably least-squares fitted by linear combination of 3-components chosen from a large model compound spectral database including synthetic and natural Ni-bearing sulfides, clay minerals, oxyhydroxides, and organic complexes. Our results show that in the inland salt flat Ni is hosted in minerals inherited from the eroded lateritic materials, i.e. Ni-poor serpentine (44-58%), Ni-rich talc (20-31%), and Ni-goethite (18-24%). In contrast, in the hydromorphic sediments beneath the vegetated Avicennia and Rhizophora stands, a large fraction of Ni is partly redistributed into a neoformed smectite pool (20-69% of Ni-montmorillonite), and Ni speciation significantly changes with depth in the sediment. Indeed, Ni-rich talc (25-56%) and Ni-goethite (15-23%) disappear below ∼15 cm depth in the sediment and are replaced by Ni-sorbed pyrite (23-52%) in redox-active intermediate depth layers and by pyrite (34-55%) in the deepest sediment layers. Ni-incorporation in pyrite is especially observed beneath an inland Avicennia stand where anoxic conditions are dominant. In contrast, beneath a Rhizophora stand closer to the ocean, where the redox cycle is intensified due to the tide cycle, partial re-oxidation of Ni-bearing pyrites favors nickel mobility, as confirmed by Ni-mass balance estimates and by higher Ni concentration in the pore waters. These findings have important environmental implications for better evaluating the protective role of mangroves against trace metal dispersion into marine ecosystems. They may also help in predicting the response of mangrove ecosystems to increasing anthropogenic pressure on coastal areas.

Mars Hematite Site: Potential for Preservation of Microfossils

NASA Technical Reports Server (NTRS)

Allen, Carlton C.; Westall, Frances; Longazo, Teresa; Schelble, Rachel; Probst, Luke; Flood, Beverly

2003-01-01

Defining locations where conditions may have been favorable for life is a key objective for the exploration of Mars. Of prime importance are sites where conditions may have been favorable for the preservation of evidence of pre-biotic or biotic processes. Areas displaying significant concentrations of the mineral hematite (alpha-Fe2O3) have been identified from orbit by thermal emission spectrometry. The largest such deposit, in Sinus Meridiani, is a strong candidate landing site for one of the twin Mars Exploration Rovers, scheduled to launch in 2003. The Martian hematite site may have significance in the search for evidence of extraterrestrial life. Since iron oxides can form as aqueous mineral precipitates, the potential exists for preserving microscopic evidence of life in ecosystems that deposit iron oxides. Terrestrial hematite deposits proposed as possible analogs for the hematite sites on Mars include massive (banded) iron formations, iron oxide hydrothermal deposits, iron-rich laterites and ferricrete soils, and rock varnish. We are engaged in a systematic effort to document the evidence of life preserved in iron oxide deposits from each of these environments.

The role of ophiolite in metallogeny of the Sikhote-Alin region

NASA Astrophysics Data System (ADS)

Kazachenko, V. T.; Perevoznikova, E. V.; Lavrik, S. N.; Skosareva, N. V.

2012-06-01

Metalliferous sediments of the Triassic siliceous formation of the Sikhote-Alin (manganese-silicate rocks and cherts with dispersed rhodochrosite, silicate-magnetite ores, and jasper) and skarns of the Dalnegorsk and Olginsk ore districts were initially the wash away products (Late Anisian-end of the Triassic) of the lateritic weathering crust on ophiolite in the islands. Manganese, iron, and other metals were deposited in the sediments of both lagoons (present-day, skarns) and island water areas (manganese-silicate and siliceousrhodochrosite rocks, silicate-magnetite ores, and jasper). Skarns contain boric and polymetallic ores thus indicating the occurrence of both shallow (periodically drying up) and quite deep (with hydrogen sulfide contamination zones) lagoons. Lead was deposited in protoliths of the skarn deposits in lagoons from the beginning of the Carboniferous to the beginning of the Late Anisian (initial island submergence). Tin, tin-leadzinc (with Ag), and silver-lead-zinc (with Sn and Au) vein deposits (Late Cretaceous-Paleogene) of the Taukha and Zhuravlevka Terrains contain lead deposited in the sediments flanking the islands of water areas with the hydrogen sulfide contamination zones, in the Carboniferous-Permian and Triassic metalliferous sediments.

[Spatiotemporal variation of soil pH in Guangdong Province of China in past 30 years].

PubMed

Guo, Zhi-Xing; Wang, Jing; Chai, Min; Chen, Ze-Peng; Zhan, Zhen-Shou; Zheng, Wu-Ping; Wei, Xiu-Guo

2011-02-01

Based on the 1980s' soil inventory data and the 2002-2007 soil pH data of Guangdong Province, the spatiotemporal variation of soil pH in the Province in past 30 years was studied. In the study period, the spatial distribution pattern of soil pH in the Province had less change (mainly acidic), except that in Pearl River Delta and parts of Qingyuan and Shaoguan (weak alkaline). The overall variation of soil pH was represented as acidification, with the average pH value changed from 5.70 to 5.44. Among the soil types in the Province, alluvial soil had an increased pH, lateritic red soil, paddy soil, and red soil had a large decrement of pH value, and lime soil was most obvious in the decrease of pH value and its area percentage. The soil acidification was mainly induced by soil characteristics, some natural factors such as acid rain, and human factors such as unreasonable fertilization and urbanization. In addition, industrialization and mining increased the soil pH in some areas.

Preliminary results from an investigation of AIS-1 data over an area of epithermal alteration: Plateau, Northern Queensland, Australia

NASA Technical Reports Server (NTRS)

Mackin, Steve; Munday, Tim; Hook, Simon

1987-01-01

Airborne Imaging Spectrometer-1 (AIS-1) data were flown over undifferentiated sequences of acid to intermediate volcanics and intrusives; meta-sediments; and a series of partially lateritized sedimentary rocks. The area exhibits a considerable spectral variability, after the suppression of striping effects. Log residual, and Internal Average Relative Reflectance (IARR) analytical techniques were used to enhance mineralogically related spectral features. Both methods produce similar results, but did not visually highlight mineral absorption features due to processing artifacts in areas of significant vegetation cover. The enhancement of mineral related absorption features was achieved using a hybrid processing approach based on the relative reflectance differences between vegetated and non-vegetated surfaces at 1.2 and 2.1 micron. The result is an image with little overall contrast, but which enhances the more subtle spectral features believed to be associated with clays and epidote. The AIS data was subject to interactive analysis using SPAM. Clear separation of clay and epidote related absorption features was apparent, and the identification of kaolinite was possible despite detrimental spectral effects.

Water in the critical zone: soil, water and life from profile to planet

NASA Astrophysics Data System (ADS)

Kirkby, M. J.

2016-12-01

Earth is unique in the combination of abundant liquid water, plate tectonics and life, providing the broad context within which the critical zone exists, as the surface skin of the land. Global differences in the availability of water provide a major control on the balance of processes operating in the soil, allowing the development of environments as diverse as those dominated by organic soils, by salty deserts or by deeply weathered lateritic profiles. Within the critical zone, despite the importance of water, the complexity of its relationships with the soil material continue to provide many fundamental barriers to our improved understanding, at the scales of pore, hillslope and landscape. Water is also a vital resource for the survival of increasing human populations. Intensive agriculture first developed in semi-arid areas where the availability of solar energy could be combined with irrigation water from more humid areas, minimising the problems of weed control with primitive tillage techniques. Today the challenge to feed the world requires improved, and perhaps novel, ways to optimise the combination of solar energy and water at a sustainable economic and environmental cost.

Riverine dissolved lithium isotopic signatures in low-relief central Africa and their link to weathering regimes

NASA Astrophysics Data System (ADS)

Henchiri, Soufian; Gaillardet, Jérôme; Dellinger, Mathieu; Bouchez, Julien; Spencer, Robert G. M.

2016-05-01

The isotopic composition of dissolved lithium (δ7Li) near the Congo River mouth varied from 14‰ to 22‰ in 2010 and was negatively correlated to discharge. From the relationship between dissolved δ7Li and strontium isotopes, we suggest that this large variation is due to mixing of waters from two contrasting continental weathering regimes. One end-member (high δ7Li ≈ 25‰) represents waters sourced from active lateritic soils covering the periphery of the basin (Li highly sequestered into secondary mineral products) and another representing blackwater rivers (low δ7Li ≈ 5.7‰) derived from the swampy central depression where high organic matter content in water leads to congruent dissolution of the Tertiary sedimentary bedrock. This suggests that the lithium isotopic signature of tropical low-relief surfaces is not unique and traces the long-term, large-scale vertical motions of the continental crust that control geomorphological settings. This evolution should be recorded in the oceanic secular δ7Li curve.

Microbial leaching of chromite overburden from Sukinda mines, Orissa, India using Aspergillus niger

NASA Astrophysics Data System (ADS)

Biswas, Supratim; Samanta, Saikat; Dey, Rajib; Mukherjee, Siddhartha; Banerjee, Pataki C.

2013-08-01

Leaching of nickel and cobalt from two physical grades (S1, 125-190 μm, coarser and S3, 53-75 μm, finer) of chromite overburden was achieved by treating the overburden (2% pulp density) with 21-d culture filtrate of an Aspergillus niger strain grown in sucrose medium. Metal dissolution increases with ore roasting at 600°C and decreasing particle size due to the alteration of microstructural properties involving the conversion of goethite to hematite and the increase in surface area and porosity as evident from X-ray diffraction (XRD), thermogravimetry-differential thermal analysis (DT-TGA), and field emission scanning electron microscopy (FESEM). About 65% Ni and 59% Co were recovered from the roasted S3 ore employing bioleaching against 26.87% Ni and 31.3% Co using an equivalent amount of synthetic oxalic acid under identical conditions. The results suggest that other fungal metabolites in the culture filtrate played a positive role in the bioleaching process, making it an efficient green approach in Ni and Co recovery from lateritic chromite overburden.

PCDD/F formation during thermal desorption of p,p'-DDT contaminated soil.

PubMed

Zhao, Zhonghua; Ni, Mingjiang; Li, Xiaodong; Buekens, Alfons; Yan, Jianhua

2017-05-01

Thermal treatment of polychlorinated biphenyls (PCB) contaminated soil was shown in earlier work to generate polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF). In this study, the PCDD/F were studied arising during the remediation of p,p'-DDT contaminated soil by thermal desorption. Three kinds of soil (sandy, clayey and lateritic soil) were tested to investigate the effect of soil texture on PCDD/F formation. Those soils were artificially polluted with p,p'-DDT, obtaining a concentration level of 100 mg/kg. Thermal desorption experiments were conducted for 10 min at 300 °C in an air atmosphere. The total concentration of PCDD/F generated for three soils were 331, 803 and 865 ng/kg, respectively, and TeCDD and TeCDF were dominant among all PCDD/F congeners. After thermal desorption, the total amount of PCDD/F generated both in soil and in off-gas correlated positively with the amount of DDT added to soil. In addition, a possible pathway of the formation of PCDD/F was presented.

Constitutive mass balance relations between chemical composition, volume, density, porosity, and strain in metasomatic hydrochemical systems: Results on weathering and pedogenesis

NASA Astrophysics Data System (ADS)

Brimhall, George H.; Dietrich, William E.

1987-03-01

Relations characterizing the chemical, physical, and mechanical changes resulting from metasomatic hydrochemical processes are developed using mass balance models which formally link chemical composition to bulk density, mineral density, volumetric properties, porosity, and amount of deformation (strain). Rigorous analysis of aqueous solute transport effects is then made possible in a variety of porous media flow environments including chemical weathering, pedogenesis (soil formation), diagenesis, ore deposition and enrichment, and metamorphism. Application of these linear constitutive relations to chemical weathering profiles shows that immobile and locally mobile chemical elements, with masses conserved on the scale of soil profiles, can be accurately identified from analysis of appropriate data arrays and then used as natural geochemical tracers to infer the nature and extent of hydrochemical weathering processes and volume changes during pedogenesis. Assumptions commonly made in the past about the supposed immobility of certain elements, e.g., Ti and Zr, become unnecessary. Quantitative differentiation between the effects of residual and supergene fractionation is then easily made. These methods are applied to Ni-rich laterites developed by weathering of ultramafic rocks, showing that during ordinary residual enrichment, Ni is concentrated by as much as 4× protolith peridotite concentrations. This occurs simply by silicate mineral dissolution and removal of chemical elements other than Ni ( e.g., Mg) with a corresponding reduction in saprolite density and increase in bulk porosity without significant deformation. In contrast, laterites with mineable concentrations of Ni which are similarly undeformed (such as the Nickel Mountain Mine in Riddle, Oregon) have experienced, in addition to residual enrichment, strong supergene enrichment by fractionation of ore elements between a leached zone from which Ni is extracted and a complementary enriched zone positioned farther along the direction of ground water flow. Soil-forming processes in podzol chronosequences developed on sandy beach terraces of the Mendocino Coast of California involved soil column collapse of 60 percent by dissolution of silicate minerals in the albic horizon of Al and Fe leaching, and 70 percent dilation (expansion) in the overlying organic-rich layer by root growth. The amount of erosion based upon paleosurface reconstructions using the excess mass of Fe, Al, Pb, Ga, and Cu in the zone of supergene enrichment (spodic horizon) below the ground water table indicates that subsurface erosion by dissolutional collapse is three times that of surficial erosion. Finally, using published chemical data for Ti, Zr, and Cr on major bauxite deposits in Australia where erosion rates are thought to be low, we infer that there may have been major amounts of dissolutional collapse to explain the upwards increase of detrital zircon and rutile in weathering profiles.

Assessment of hydrogeochemical status of groundwater in a coastal region of Southeast coast of India

NASA Astrophysics Data System (ADS)

Chidambaram, S.; Sarathidasan, J.; Srinivasamoorthy, K.; Thivya, C.; Thilagavathi, R.; Prasanna, M. V.; Singaraja, C.; Nepolian, M.

2018-03-01

A study was conducted in a coastal region of Cuddalore district of Tamil Nadu, India, to identify the hydrogeochemical processes controlling the groundwater chemistry. The major geological units of the study area are sandstone, clay, alluvium, and laterite soils of Tertiary and Quaternary age. A total of 64 groundwater samples were measured for major ions and stable isotopes. Higher electrical conductivity values indicate the poor quality groundwater along the coastal region. Saline water intrusion mainly affects the hydrochemical composition of the aquifer water reflected by Na-Cl-type waters. Cl-/(Cl- + HCO3 -) ratio also indicates the mixing of fresh groundwater with saline water. The results of δD and δ18O analyses show that isotopic compositions of groundwater ranges from - 7.7 to - 2.1‰ for δ18O and from - 55.6 to - 18.5‰ for δD. Correlation and factor analysis were carried out to find the association of ions and to determine the major factors controlling the groundwater chemistry of the region. The study indicates that ion exchange, weathering, salt water intrusion along the coast, and anthropogenic impacts are the major controlling factors for the groundwater chemistry of the region.

ERT and Well Data Tie for Nickel Laterite Characterization

NASA Astrophysics Data System (ADS)

Aswad, Sabrianto; Mamela Mais, Difar; Syamsuddin; Wanni

2018-03-01

The need of ERT method in nickel latentes exploration can’t be deny. This method have capability to make exploration more effective and efficient. In reality this method still remain ambiguity in its application, especially for geologist and mining expert. These ambiguity related with layer zone determination (limonite, saprolite and bedrock), the same resistivity values in the different zones and determination of bedrock. This paper try to expose interesting fact to overcome this ambiguity by using ERT data and drill data tie. This tie will show characteristic of nickel lateric based on resisitivity value and the contribution of chemistry element for resistivity value. Data ERT was collected by using gradient configuration and well data consist of mayor element and minor element. Tie result showed difference resistivity value in limonite layer influence by Fe, H2O and Ni, where resistivity value from saprolite layer influenced by Fe, H2O, Si02, MgO, Al, Cr, and Ni in certain accumulation. In bedrock layer, almost all drill data did not reach bedrock but only reached the boulder alone, it is supported by the value of the resistivity of rock unserpentinized peridotite which should show a relatively large resistivity value

Effect of Cr2O3 Pickup on Dissolution of Lime in Converter Slag

NASA Astrophysics Data System (ADS)

Yan, Wei; Chen, Weiqing; Zhao, Xiaobo; Yang, Yindong; McLean, Alex

2017-09-01

Application of low-nickel laterite ore containing chromium as charging material for ironmaking can reduce raw material costs, but result in an increase of chromium content in the hot metal and hence, Cr2O3 content in the steelmaking slag, which subsequently causes many problems related to lime dissolution for the steelmaking operation. In this work, a rotating cylinder method was employed to study the effect of Cr2O3 on lime dissolution in steelmaking slag. The lime dissolution mechanism, rate control step and affecting factors, including slag basicity, FeOx and B2O3 content, and the formation of phases at reacted layer, were discussed. It was found that mass transfer was the rate control step in slag phase, increase of Cr2O3 and slag basicity delayed lime dissolution due to the formation of high-melting temperature phases of FeO · Cr2O3 spinel and 2CaO · SiO2 at the slag/lime reacted interface. Addition of B2O3 promoted lime dissolution and suppressed formation of FeO · Cr2O3 spinel.

Mima mounds in the Kenya highlands: significance for the Dalquest-Scheffer hypothesis.

PubMed

Cox, George W; Gakahu, Christopher G

1983-03-01

The Dalquest-Scheffer Hypothesis that Mima mounds in western North America are the long-term product of burrowing activities of geomyid pocket gophers was tested by examination of areas of similar topography in the highlands of Kenya. Two mound areas, located near Nyahururu at an elevation of about 2,400 m, were studied in detail. The mounds ranged from less than 25 cm to 2 m in height and from a few m to about 20 m in diameter, and were not the remains of large termite nests. Populations of the rhizomyid mole rat, Tachyoryctes splendens, a fossorial rodent similar in morphology and social behavior to geomyid pocket gophers, were associated with these mounds. Mound density and dispersion pattern were similar to North American Mima mounds, and the distribution of fresh soil heaps indicated that the activities of these animals were mound-centered. A shallow laterite hardpan underlay these mound areas, fulfilling another requirement of the Dalquest-Scheffer hypothesis. It is concluded that Mima mounds are the product of the burrowing of fossorial rodents such as pocket gophers and mole rats, and that these two groups are convergent in morphology, burrowing behavior, and impact on the landscape.

Different depth intermittent sand filters for laboratory treatment of synthetic wastewater with concentrations close to measured septic tank effluent.

PubMed

Rodgers, M; Walsh, G; Healy, M G

2011-01-01

The objective of this study was to apply hydraulic and chemical oxygen demand (COD) loading rates at the upper limits of the design criteria for buried sand filters to test the sand filter depth design criteria. Over a 274-day study duration, synthetic effluent with a strength of domestic wastewater was intermittently dosed onto two sand filters of 0.2 m diameter, with depths of 0.3 and 0.4 m. Hydraulic and organic carbon loading rates of 105 L m(-2) d(-1) and 40 g COD m(-2) d(-1), respectively, were applied to the filters. The filters did not clog and had good effluent removal capabilities for 274 and 190 days, respectively. However, the 0.3 m-deep filter did experience a reduced performance towards the end of the study period. In the 0.3 and 0.4 m-deep filters, the effluent COD and SS concentrations were less than 86 and 31 mg L(-1), respectively, and nitrification was nearly complete in both these columns. Ortho-phosphorus (PO(4)-P) removal in fine sand and laterite 'upflow' filters, receiving effluent from the 0.3 m-deep filter, was 10% and 44%, respectively.

Cassava; African perspective on space agriculture

NASA Astrophysics Data System (ADS)

Katayama, Naomi; Njemanze, Philip; Nweke, Felix; Space Agriculture Task Force, J.; Katayama, Naomi; Yamashita, Masamichi

Looking on African perspective in space agriculture may contribute to increase diversity, and enforce robustness for advanced life support capability. Cassava, Manihot esculentaand, is one of major crop in Africa, and could be a candidate of space food materials. Since resource is limited for space agriculture in many aspects, crop yield should be high in efficiency, and robust as well. The efficiency is measured by farming space and time. Harvest yield of cassava is about 41 MJ/ m2 (70 ton/ha) after 11 months of farming. Among rice, wheat, potato, and sweet potato, cassava is ranked to the first place (40 m2 ) in terms of farming area required to supply energy of 5 MJ/day, which is recommended for one person. Production of cassava could be made under poor condition, such as acidic soil, shortage of fertilizer, draught. Laterite, similar to Martian regolith. Propagation made by stem cutting is an advantage of cassava in space agriculture avoiding entomophilous or anemophilous process to pollinate. Feature of crop storage capability is additional factor that determines the efficiency in the whole process of agriculture. Cassava root tuber can be left in soil until its consumption. Cassava might be an African contribution to space agriculture.

Identification of areas of recharge and discharge using Landsat-TM satellite imagery and aerial photography mapping techniques

NASA Astrophysics Data System (ADS)

Salama, R. B.; Tapley, I.; Ishii, T.; Hawkes, G.

1994-10-01

Aerial photographs (AP) and Landsat (TM) colour composites were used to map the geomorphology, geology and structures of the Salt River System of Western Australia. Geomorphic features identified are sand plains, dissected etchplain, colluvium, lateritic duricrust and rock outcrops. The hydrogeomorphic units include streams, lakes and playas, palaeochannels and palaeodeltas. The structural features are linear and curvilinear lineaments, ring structures and dolerite dykes. Suture lines control the course of the main river channel. Permeable areas around the circular granitic plutons were found to be the main areas of recharge in the uplands. Recharge was also found to occur in the highly permeable areas of the sandplains. Discharge was shown to be primarily along the main drainage lines, on the edge of the circular sandplains, in depressions and in lakes. The groundwater occurrence and hydrogeological classification of the recharge potential of the different units were used to classify the mapped areas into recharge and discharge zones. The results also show that TM colour composites provide a viable source of data comparable with AP for mapping and delineating areas of recharge and discharge on a regional scale.

Tests on the centrifugal flotation technique and its use in estimating the prevalence of Toxocara in soil samples from urban and suburban areas of Malaysia.

PubMed

Loh, A G; Israf, D A

1998-03-01

The influence of soil texture (silt, sand and laterite) and flotation solutions (saturated NaCl, sucrose, NaNO3, and ZnSO4) upon the recovery of Toxocara ova from seeded soil samples with the centrifugal flotation technique was investigated. Soil samples of different texture were artificially seeded with Toxocara spp. ova and subjected to a centrifugal flotation technique which used various flotation solutions. The results showed significant (P < 0.001) interactions between the soil types and the flotation solutions. The highest percentage of ova recovery was obtained with silty soil (34.9-100.8%) with saturated NaCl as the flotation solution (45.3-100.8%). A combination of washing of soil samples with 0.1% Tween 80, and flotation using saturated NaCl and a 30 min coverslip recovery period was used to study the prevalence of contamination of soil samples. Forty-six soil samples were collected from up to 24 public parks/playgrounds in urban areas of Petaling Jaya and suburban areas of Serdang. The prevalence of Toxocara species in the urban and suburban areas was 54.5% and 45.8% respectively.

Lithofacies and palynostratigraphy of some Cretaceous and Paleocene rocks, Surghar and Salt Range coal fields, northern Pakistan

USGS Publications Warehouse

Warwick, Peter D.; Javed, Shahid; Mashhadi, S. Tahir A.; Shakoor, Tariq; Khan, Asrar M.; Khan, A. Latif

1995-01-01

The stratigraphic relation between the Cretaceous generally non-coal-bearing Lumshiwal Formation (64 to 150 m thick) and the Paleocene coal-bearing Hangu Formation (5 to 50 m thick) in the Surghar Range of north-central Pakistan is complex. Both formations contain remarkably similar lithofacies: one or two types of sandstone lithofacies; a combined lithofacies of mudstone, claystone, carbonaceous shale, and coal beds; and a rare carbonate lithofacies. An analysis of pollen data from rock samples collected from various stratigraphic positions indicates that the formations are separated by a disconformity and that the age of the Lumshiwal Formation is Early Cretaceous and the age of the Hangu is Paleocene. Previous workers had suggested that the age of the Lumshiwal is Late Cretaceous. An analysis of sedimentologic, stratigraphic, and paleontologic data indicates that both the Lumshiwal and Hangu Formations probably were deposited in shallow-marine and deltaic environments. The rocks of the Lumshiwal become more terrestrial in origin upward, whereas the rocks of the Hangu become more marine in origin upward. The contact between the two formations is associated with a laterally discontinuous lateritic paleosol (assigned to the Hangu Formation) that is commonly overlain by the economically important Makarwal coal bed. This coal bed averages 1.2 m in thickness. No other coal beds in the Surghar Range are as thick or as laterally continuous as the Makarwal coal bed. Analytical data from the Makarwal and one other Hangu coal bed indicate that Surghar Range coal beds range from high-volatile B to high-volatile C bituminous in apparent rank. Averaged, as-received results of proximate and ultimate analyses of coal samples are (1) moisture content, 5.4 percent; (2) ash yield, 12.5 percent; (3) total sulfur content, 5 percent; and (4) calorific value, 11034 Btu/lb (British thermal units per pound). Minor- and trace-element analyses indicate that these coals contain relatively high concentrations of the environmentally sensitive element selenium (average 13.4 ppm (parts per million)), compared to concentrations from United States coals of similar rank. The Makarwal coal bed represents a paleopeat that formed during changing relative ground-water base levels. Relatively low base levels were associated with periods of slow clastic deposition and lateritic paleosol development, followed by relatively high base levels that coincided with increased runoff, marine flooding, and clastic sedimentation that buried the paleopeat of the Makarwal. These environments formed along the northwestern margin of the Indian subcontinent as it drifted northward through equatorial latitudes in the Tethys Sea. The Makarwal coal bed is thin or absent in the northern part of the range where the Lumshiwal and Hangu Formations are the thinnest. Such rapid lateral changes (over about 25 km) in formation thickness and the apparent change in relative ground-water base level indicate that tectonically induced subsidence rates varied across the Surghar Range and influenced the deposition of the rocks that compose the two formations.

Application of Nutrient Enriched Biochar to Grow Bananas at the Plantation Scale

NASA Astrophysics Data System (ADS)

Nzengung, Valentine

2017-04-01

The majority of soils in Cameroon consist of varying laterites derived from granites. The lateritic soils are generally depleted in nutrients. The most fertile soils in Cameroon are young soils that have formed from volcanic rocks of the Cameroon volcanic line (CVL). The richer volcanic soils which are found in the southwest region and the western regions are used to grow the major cash crops, including cocoa, coffee, rubber, banana, tea, and palm fruits. The government owned Cameroon Development Corporation (CDC) and private commercial farmers in the country have resorted to the heavy use of imported agrochemicals to mitigate the serious and persistent soil fertility challenges. Cameroon is the third largest biomass producer in Africa. This means that Cameroon has a high biomass production potential. Among the many types of biomass available for biochar production in Cameroon, empty fruit bunches (EFB) from the many palm oil plantations offer one of the largest concentration of biomass. CDC alone produces over 200,000 tons of EFB biomass each year. The corporation uses less than half of the EFB it produces in its palm oil processing mills for mulching. The remaining EFB are disposed by open burning leading to significant air pollution. In 2015, we entered into a collaborative understanding with CDC to dispose some of its EFB by pyrolysis to produce biochar. The produced biochar is enriched with natural plant nutrients obtained from animal waste (poultry chicken manure) and volcanic lava dust from the 2001 eruption of Mount Cameroon. The biochar, chicken litter and volcanic rock dust is aged for 14 - 21 days to produce a 100% natural soil enhancer commercialized under the name "QwikGro". The QwikGro is undergoing field evaluation on three hectares of banana plantation owned by CDC. The field trial began in June 2016. Of the three hectares, one hectare of the bananas was planted using 100% (only) QwikGro, the second hectare was planted with 50% QwikGro and received 50% of the dose of artificial fertilizer that CDC uses to grow its bananas. The control was planted and fertilized with artificial fertilizer only. The banana growth parameters collected so far (24 weeks after the bananas were planted) have showed no statistical difference among the three fertigation regimes. The bananas grown with 100% QwikGro showed signs of nitrogen deficiency after three months and were provided with 50% of the mass of QwikGro used at planting. Specifically, the 100% QwikGro mats each received 8 kg of QwikGro at planting and 4 kg after three months. Meanwhile, the 50% QwikGro mats received 4 kg of QwikGro at planting and 2 kg after three months. Flowering and fruiting was observed after 20 weeks. Our presentation will include details on our nutrient enrichment methods, the banana bunch weight and the fruit physical and nutritional parameters at maturity.

Cobalt mineral exploration and supply from 1995 through 2013

USGS Publications Warehouse

Wilburn, David R.

2011-01-01

The global mining industry has invested a large amount of capital in mineral exploration and development over the past 15 years in an effort to ensure that sufficient resources are available to meet future increases in demand for minerals. Exploration data have been used to identify specific sites where this investment has led to a significant contribution in global mineral supply of cobalt or where a significant increase in cobalt production capacity is anticipated in the next 5 years. This report provides an overview of the cobalt industry, factors affecting mineral supply, and circumstances surrounding the development, or lack thereof, of key mineral properties with the potential to affect mineral supply. Of the 48 sites with an effective production capacity of at least 1,000 metric tons per year of cobalt considered for this study, 3 producing sites underwent significant expansion during the study period, 10 exploration sites commenced production from 1995 through 2008, and 16 sites were expected to begin production by 2013 if planned development schedules are met. Cobalt supply is influenced by economic, environmental, political, and technological factors affecting exploration for and production of copper, nickel, and other metals as well as factors affecting the cobalt industry. Cobalt-rich nickel laterite deposits were discovered and developed in Australia and the South Pacific and improvements in laterite processing technology took place during the 1990s and early in the first decade of the 21st century when mining of copper-cobalt deposits in Congo (Kinshasa) was restricted because of regional conflict and lack of investment in that country's mining sector. There was also increased exploration for and greater importance placed on cobalt as a byproduct of nickel mining in Australia and Canada. The emergence of China as a major refined cobalt producer and consumer since 2007 has changed the pattern of demand for cobalt, particularly from Africa and Australasia. Chinese companies are increasingly becoming involved in copper and cobalt exploration and mining in Congo (Kinshasa) and Zambia as well as nickel, copper, and other mining in Australia and the South Pacific. Between 2009 and 2013, mines with a cumulative capacity of more than 100,000 metric tons per year of cobalt were proposed to come into production if all sites came into production as scheduled. This additional capacity corresponds to 175 percent of the 2008 global refinery production level. About 45 percent of this cobalt would be from primary nickel deposits, about 32 percent from primary copper deposits, and about 21 percent from primary cobalt deposits. By 2013, about 40 percent of new capacity was expected to come from the African Copperbelt; 38 percent, from Australia and the South Pacific countries of Philippines, Indonesia, New Caledonia, and Papua New Guinea; 11 percent, from other African countries; 5 percent, from North America; and 6 percent, from other areas.

Hawaii and Beyond: Volcanic Islands as Model Systems for Biogeochemical and Human Ecodynamic Research

NASA Astrophysics Data System (ADS)

Chadwick, O.

2012-12-01

The Hawaiian Islands provide an excellent natural lab for understanding geochemical and ecosystem processes. The most important features are: a) increasing volcano age with distance from the hotspot, b) asymmetric rainfall distribution imposed by the northeasterly trade winds and orographic processes, creating wet windward and dry leeward landscapes, c) an impoverished vegetation assemblage allowing the same species to grow in strongly varying climate and soil conditions, d) the ability to hold topography relatively constant over long time scales by sampling on volcanic shield remnants that are preserved even on the oldest high island, Kauai, and e) a long-term topographic evolution that carves the gently sloping shield surfaces into steep-sided, amphitheater headed, relatively flat floored valleys. Although deeply incised valleys are well represented in Kauai, the later stages of volcanic island evolution are not well expressed in the exposed Hawaiian Islands. Therefore, I also consider examples from the Society and Gambier Islands in French Polynesia to demonstrate the biogeochemical and human ecodynamic impacts of valley expansion and subsidence leading to drowning of all but the highest elevation interfluves. In Hawaii, I and many colleagues have characterized the details of biogeochemical processes such as: a) variations in oxygen isotopes in soil water and soil minerals, b) changing nutrient sources using Sr, Ca, and Mg isotopes, c) mineral - carbon sorption and its implications for carbon storage in soils and for mineral ripening, and d) the development of leaching and redox driven pedogenic thresholds. Here, I address how these biogeochemical features influence human land-use decisions in prehistoric Hawaii and elsewhere in the Pacific. Polynesian radiation into the eastern Pacific occurred rapidly after 1300 y bp. Although they carried with them a kitchen garden each new island presented a different environmental challenge. They were sensitive to topographic and weathering conditions and adjusted their agricultural efforts accordingly. On young minimally eroded islands they favored dryland agriculture in the uplands - there being nowhere to establish extensive irrigation systems - whereas on older islands they favored irrigated lands in the extensive eroded valleys - the soil nutrient status being too depleted in the uplands. Thus Hawaii has most dryland agriculture and Kauai has most irrigated agriculture. Islands such as Easter Island created a problem because the upland soils were nutrient depleted and there were no valleys. On Moorea, valleys provided substantial areas for irrigation. However much of the uplands had infertile lateritic soils, which in places are covered by landslide deposits that contained very rocky and nutrient-rich soils. Archeological surveys demonstrate that religious and house features were sited on the lateritic soils whereas agriculture was practiced on the landslide deposits. The Gambier Islands are composed of steep highly eroded slopes and small valleys. The valleys were the only place where agriculture could be developed and it is clear that they were the locus of considerable alluvial/colluvial deposition during prehistory and even more so during historic times.

Soil-vegetation relationships on a banded ironstone 'island', Carajás Plateau, Brazilian Eastern Amazonia.

PubMed

Nunes, Jaquelina A; Schaefer, Carlos E G R; Ferreira Júnior, Walnir G; Neri, Andreza V; Correa, Guilherme R; Enright, Neal J

2015-01-01

Vegetation and soil properties of an iron-rich canga (laterite) island on the largest outcrop of banded-iron formation in Serra de Carajás (eastern Amazonia, Brazil) were studied along a topographic gradient (738-762 m asl), and analyzed to test the hypothesis that soil chemical and physical attributes play a key role in the structure and floristic composition of these plant communities. Soil and vegetation were sampled in eight replicate plots within each of the four vegetation types. Surface (0-10 cm) soil samples from each plot were analyzed for basic cations, N, P and plant species density for all species was recorded. CCA ordination analysis showed a strong separation between forest and non-forest sites on the first axis, and between herbaceous and shrubby campo rupestre on the second axis. The four vegetation types shared few plant species, which was attributed to their distinctive soil environments and filtering of their constituent species by chemical, physical and hydrological constraints. Thus, we can infer that Edaphic (pedological) factors are crucial in explaining the types and distributions of campo rupestre vegetation associated with ferruginous ironstone uplands (Canga) in Carajás, eastern Amazonia, therefore the soil properties are the main drivers of vegetation composition and structure on these ironstone islands.

Nano-Sized Natural Colorants from Rocks and Soils

NASA Astrophysics Data System (ADS)

Ahmad, W. Y. W.; Ruznan, W. S.; Hamid, H. A.; Kadir, M. I. A.; Yusoh, M. K. M.; Ahmad, M. R.

2010-03-01

Colored rocks (lateritic) and soils (shales) are available in abundant all around Malaysia and they are from natural sources. The colorants will be useful if they can be transferred to substrates using dyeing, printing or brushing with acceptable fastness. First of all the rocks need to be crushed into powder form before coloration can take place. The sizes of the colorants particles obtained with coffee grinder were of 7-8 microns. They can be reduced to 3-5 micron using fluidized bed jetmill and to nano sizes with the help of planetary mono mill grinders. The experiment was conducted in both dyeing and printing of textiles using all three sizes (7-8 microns, 3-5 microns and nano sizes) of colorants on silk fabric. The colorants were applied on silk fabrics by dyeing and tie and dye techniques. In addition, the colorants can also be applied by brushing technique as in batik canting or batik block as well as silk screen printing. The evaluations of colored materials were based on the levelness of dyeing, fastness properties (washing, light and rubbing fastness) and color strength. The wash fastness testing shows that all colorants sizes have more or less the same fastness to washing but nano sized colorants produced better uniform dyes distribution (levelness of dyeing) and higher color strength.

Critical parameters in the production of ceramic pot filters for household water treatment in developing countries.

PubMed

Soppe, A I A; Heijman, S G J; Gensburger, I; Shantz, A; van Halem, D; Kroesbergen, J; Wubbels, G H; Smeets, P W M H

2015-06-01

The need to improve the access to safe water is generally recognized for the benefit of public health in developing countries. This study's objective was to identify critical parameters which are essential for improving the performance of ceramic pot filters (CPFs) as a point-of-use water treatment system. Defining critical production parameters was also relevant to confirm that CPFs with high-flow rates may have the same disinfection capacity as pots with normal flow rates. A pilot unit was built in Cambodia to produce CPFs under controlled and constant conditions. Pots were manufactured from a mixture of clay, laterite and rice husk in a small-scale, gas-fired, temperature-controlled kiln and tested for flow rate, removal efficiency of bacteria and material strength. Flow rate can be increased by increasing pore sizes and by increasing porosity. Pore sizes were increased by using larger rice husk particles and porosity was increased with larger proportions of rice husk in the clay mixture. The main conclusions: larger pore size decreases the removal efficiency of bacteria; higher porosity does not affect the removal efficiency of bacteria, but does influence the strength of pots; flow rates of CPFs can be raised to 10-20 L/hour without a significant decrease in bacterial removal efficiency.

Soil Compaction Assessment Using Spectral Analysis of Surface Waves (SASW)

NASA Astrophysics Data System (ADS)

Afiq Roslan, Muhammad; Madun, Aziman; Hazreek Zainalabidin, Mohd; Dan@Azlan, Mohd Firdaus Md; Khaidir Abu Talib, Mohd; Nur Hidayat Zahari, Muhammad; Ambak, Kamaruddin; Ashraf Mohamad Ismail, Mohd

2018-04-01

Compaction is a process of soil densification in earthworks via by pressing the soil particles with air being expelled from the soil mass, thereby increasing its unit weight. Thus, it is important to evaluate the quality of soil compaction as prescribed in the technical requirement. SASW method is widely used for estimating material properties in layered structures based on the dispersion characteristics of Rayleigh Waves. The small scale at dimension area of 1.0 m width x 1.0 m length x 0.9 m depth was excavated and back filled with laterite soil. The soil was compacted for every layer at 0.3 m thickness. Each layer of soil compaction was conducted compaction test using core cutter methods and SASW test to determine the density and shear wave velocity. The phase velocity for layer 1 was between 112 m/s and 114 m/s, layer 2 was between 67 m/s and 74 m/s and layer 3 was between 74 m/s and 97 m/s. The result shows that the compacted soil layers are not fulfilled the quality of compacted soil layers where supposedly the expected shear wave velocity for the compacted layers should be higher than 180 m/s which is classified as stiff soil.

Mixing mechanisms in siliciclastic-carbonate successions of Khan Formation (Permian), Central Iran

NASA Astrophysics Data System (ADS)

Shadan, Mahdi; Hosseini-Barzi, Mahboubeh

2010-05-01

Mixing mechanisms in siliciclastic-carbonate successions of Khan Formation (Permian), Central Iran M. Shadan & M. Hosseini-Barzi Geology Department, Faculty of Earth Science, Shahid Beheshti University, Tehran, Iran shadangeo@gmail.com Mixing mechanisms in siliciclastic-carbonate successions of Khan Formation (Permian) have been studied in two sections (Chahroof with 197 m thick in north and Cheshmeh Bakhshi with 204 m thick in south) along basement Kalmard fault in Posht-e-Badam block, Central Iran. Siliciclastic units are characterized by well sorted, fine to medium grain quartzarenites with laterite interbeds, deposited in shoreline zone (foreshore, upper and lower shoreface) influencing wave and longshore currents. Longshore sands which have been transported along the coast made the sand bars in the shoreface. Further along the coast, returning of these currents as rip currents produced erosive channel inlets and caused to carry fine grain into the deeper regions of the basin. Based on this sedimentary model we introduced longshore currents as a probable agent for mixing, by transporting some volumes of sands into the adjacent carbonate environments. Vertically, clastic units of Khan Formation underlined by carbonate units of a tidal flat and high-energy inner ramp system. Repeating of this pattern produced 3 cycles in each section. Cyclic evolution, in studied sections, is accompanied with discrepancy in erosion and sedimentation. These factors caused to disperse local sub-aerial exposures in successions which are recognizable by laterite and conglomerate interbeds. These horizons of sub-aerial exposures are more often in Chahroof section than in Cheshmeh Bakhshi section and indicate more fluctuations of relative sea level probably due to more local tectonic activity in the northern part of the Kalmard fault than in the southern part of it. Also, thicker siliciclastic units in Chahroof section show higher rate of sediment supply and/or more accommodation space there. Moreover, the late Paleozoic glacial conditions in Gondwana lands supported the large volume of clastic supply into the basin by intense weathering and erosion of vast exposed regions in Posht-e-Badam block. Also, tectonic activity along Kalmard basement fault mainly controlled local sea level changes and lithology of outcrops in the hinterlands. Therefore, interplay of these factors during lowstand of relative sea level, with lower accommodation space and higher gradient led to high rate of sediment input and distribution of siliciclastics in the base of each cycles. In contrast, relative sea level rises have been corresponded to the more accommodation space and reducing of siliciclastic entrance into the sedimentary basin that made a suitable condition for carbonate production. Therefore, during relative sea level rise, verities of carbonate-producing organisms tend to more rates of biogenic carbonate products and eventually formation of carbonate units upon the preexistence silisiclastics. Therefore, mixing of siliciclastics with carbonate deposits in Khan Formation have mainly been controlled temporally by sea level fluctuations due to local and/or eustatic sea level changes and spatially by variations in local tectonic activities and lateral facies mixing by longshore currents.

Behavior of major and trace elements upon weathering of peridotites in New Caledonia : A possible site on ultramafic rocks for the Critical Zone Exploration Network (CZEN) ?

NASA Astrophysics Data System (ADS)

Juillot, Farid; Fandeur, D.; Fritsch, E.; Morin, G.; Ambrosi, J. P.; Olivi, L.; Cognigni, A.; Hazemann, J. L.; Proux, O.; Webb, S.; Brown, G. E., Jr.

2010-05-01

Ultramafic rocks cover about 1% of the continental surfaces and are related to ophiolitic bodies formed near convergent plate boundaries (Coleman, 1977). The most typical ultramafic rocks are dunite and harzburgite, which are composed of easily weatherable ferromagnesian mineral species (olivines and pyroxenes), but also of more resistant spinels (chromite and magnetite). Oceanic serpentinization of these ultramafic rocks usually lead to partial transformation of these initial mineral assemblages by forming hydrous layer silicates such as serpentine (lizardite, chrysotile and antigorite) talc, chlorite and actinolite (Malpas, 1992). It also lead to the formation of highly sheared textures, which favor meteoric weathering through preferential water flows. Compared to their crystalline rock counterpart that covers most of the continental surfaces, these ultramafic rocks mainly differ by their lower SiO2, Al2O3 and K2O contents (less than 50%, 10% and 1%, respectively) and, on the opposite, much higher MgO content (more than 18%). Moreover, they commonly have higher concentrations in FeO and other trace elements, such as Ni, Cr, Mn and Co. Weathering of these rocks is then at the origin of major geochemical anomalies on continental surfaces, especially when they occur in tropical and subtropical regions. Such conditions are encountered in New Caledonia where one third of the surface is covered with peridotites (mainly harzburgite with small amounts of dunite) obducted about 35 millions years ago during large tectonic events in the Southwest Pacific at the Late Eocene (Cluzel et al., 2001). Tropical weathering of these ultramafic rocks lead to the development of thick lateritic regoliths where almost all Mg and Si have been leached out and Fe, Mn, Ni, Cr and Co have been relatively concentrated. In these oxisols, Ni, Cr and Co can exhibit concentration up to several wt%, which make them good candidates for ore mining (New Caledonia is the third Ni producer in the world). However, these high concentration of potentially toxic elements can represent a serious hazard for the environmental quality of the Caledonian ecosystem which is a '' biodiversity hotspot' (Myers, 2000), which emphasize the strong need for characterizing the natural cycling of these elements upon weathering of ultramafic rocks. To reach this goal, we have studied the mineralogical distribution, crystal-chemistry and mass balance modelling of major (Si, Mg, Al, Fe, Mn) and trace elements (Ni, Cr and Co) in the freely-drained weathering profile developed in the serpentinized harzburgites of Mt Koniambo (West Coast of New Caledonia). Results show that both hydrothermal and meteoric processes contributed to the vertical differentiation of this freely drained weathering profiles in serpentinized ultramafic rocks. Finally, they also emphasize the importance of both redox reactions and interactions with Mn- and Fe-oxyhydroxydes (Fandeur et al., 2009a; 2009b) to explain the opposite behavior observed between very mobile Ni and almost immobile Cr (Fandeur et al., 2010). These results bring new insights on the geochemical behavior of trace elements upon weathering of ultramafic rocks under tropical conditions leading to the formation of supergene ore deposits. They also emphasize the interest of such a weathering site on ultramafic rocks under tropical climate to complemente the reference sites of the Critical Zone Exploration Network (CZEN). References Cluzel D., Aitchinson J.C. and Picard C. (2001) Tectonic accretion and underplating of mafic terranes in the Late Eocene intraoceanic fore-arc of New-Caledonia (Southwest Pacific): geodynamic implications. Tectonophysics, 340, 23-59. Coleman, R.G. (1977) Ophiolites: Ancient oceanic lithosphere?: Berlin, Germany, Springer-Verlag, 229p. Fandeur D., Juillot F., Morin G., Olivi L., Cognigni A., Fialin M., Coufignal F., Ambrosi J.P., Guyot F. and Fritsch E. (2009a). Synchrotron-based speciation of chromium in an Oxisol from New-Caledonia : Importance of secondary Fe-oxyhydroxydes. American Mineralogist, 94, 710-719. Fandeur D., Juillot F., Morin G., Olivi L., Cognigni A., Webb S., Ambrosi J.P., Fritsch E. and Brown Jr. G.E. (2009b). XANES evidence for oxidation of Cr(III) to Cr(VI) by Mn-oxides in a lateritic regolith developed on serpentinized ultramafic rocks in New Caledonia. Environmental Science and Technology, 43, 7384-7390. Fandeur D., Fritsch E., Juillot F., Morin G., and Ambrosi J.P. (2010). Influence of mineralization and weathering on the distribution and mobility of major and trace elements along a freely-drained lateritic regolith developed in ultramafic rocks in New-Caledonia. Chemical Geology, submitted. Malpas J. (1992) Serpentine and the geology of serpentinized rocks. In The ecology of aeras with serpentinized rocks, Roberts B.A. and Proctor J (eds), Kluwer Academic Publishers, Netherland. Myers, N., R. A. Mittermeier, C. G. Mittermeier, G. A. B. da Fonseca, J. Kent (2000) Biodiversity hotspots for conservation priorities. Nature, 403, 853-858.

Plant-associated fluorescent Pseudomonas from red lateritic soil: Beneficial characteristics and their impact on lettuce growth.

PubMed

Maroniche, Guillermo A; Rubio, Esteban J; Consiglio, Adrián; Perticari, Alejandro

2016-11-25

Fluorescent Pseudomonas are ubiquitous soil bacteria that usually establish mutualistic associations with plants, promoting their growth and health by several mechanisms. This makes them interesting candidates for the development of crop bio-inoculants. In this work, we isolated phosphate-solubilizing fluorescent Pseudomonas from the rhizosphere and inner tissues of different plant species growing in red soil from Misiones, Argentina. Seven isolates displaying strong phosphate solubilization were selected for further studies. Molecular identification by rpoD genotyping indicated that they belong to different species within the P. fluorescens and P. putida phylogenetic groups. Screening for in vitro traits such as phosphate solubilization, growth regulators synthesis or degradation, motility and antagonism against phytopathogens or other bacteria, revealed a unique profile of characteristics for each strain. Their plant growth-promoting potential was assayed using lettuce as a model for inoculation under controlled and greenhouse conditions. Five of the strains increased the growth of lettuce plants. Overall, the strongest lettuce growth promoter under both conditions was strain ZME4, isolated from inner tissues of maize. No clear association between lettuce growth promotion and in vitro beneficial traits was detected. In conclusion, several phosphate solubilizing pseudomonads from red soil were isolated that display a rich array of plant growth promotion traits, thus showing a potential for the development of new inoculants.

The Paleoproterozoic snowball Earth: a climate disaster triggered by the evolution of oxygenic photosynthesis.

PubMed

Kopp, Robert E; Kirschvink, Joseph L; Hilburn, Isaac A; Nash, Cody Z

2005-08-09

Although biomarker, trace element, and isotopic evidence have been used to claim that oxygenic photosynthesis evolved by 2.8 giga-annum before present (Ga) and perhaps as early as 3.7 Ga, a skeptical examination raises considerable doubt about the presence of oxygen producers at these times. Geological features suggestive of oxygen, such as red beds, lateritic paleosols, and the return of sedimentary sulfate deposits after a approximately 900-million year hiatus, occur shortly before the approximately 2.3-2.2 Ga Makganyene "snowball Earth" (global glaciation). The massive deposition of Mn, which has a high redox potential, practically requires the presence of environmental oxygen after the snowball. New age constraints from the Transvaal Supergroup of South Africa suggest that all three glaciations in the Huronian Supergroup of Canada predate the Snowball event. A simple cyanobacterial growth model incorporating the range of C, Fe, and P fluxes expected during a partial glaciation in an anoxic world with high-Fe oceans indicates that oxygenic photosynthesis could have destroyed a methane greenhouse and triggered a snowball event on time-scales as short as 1 million years. As the geological evidence requiring oxygen does not appear during the Pongola glaciation at 2.9 Ga or during the Huronian glaciations, we argue that oxygenic cyanobacteria evolved and radiated shortly before the Makganyene snowball.

Regolith-geology mapping with support vector machine: A case study over weathered Ni-bearing peridotites, New Caledonia

NASA Astrophysics Data System (ADS)

De Boissieu, Florian; Sevin, Brice; Cudahy, Thomas; Mangeas, Morgan; Chevrel, Stéphane; Ong, Cindy; Rodger, Andrew; Maurizot, Pierre; Laukamp, Carsten; Lau, Ian; Touraivane, Touraivane; Cluzel, Dominique; Despinoy, Marc

2018-02-01

Accurate maps of Earth's geology, especially its regolith, are required for managing the sustainable exploration and development of mineral resources. This paper shows how airborne imaging hyperspectral data collected over weathered peridotite rocks in vegetated, mountainous terrane in New Caledonia were processed using a combination of methods to generate a regolith-geology map that could be used for more efficiently targeting Ni exploration. The image processing combined two usual methods, which are spectral feature extraction and support vector machine (SVM). This rationale being the spectral features extraction can rapidly reduce data complexity by both targeting only the diagnostic mineral absorptions and masking those pixels complicated by vegetation, cloud and deep shade. SVM is a supervised classification method able to generate an optimal non-linear classifier with these features that generalises well even with limited training data. Key minerals targeted are serpentine, which is considered as an indicator for hydrolysed peridotitic rock, and iron oxy-hydroxides (hematite and goethite), which are considered as diagnostic of laterite development. The final classified regolith map was assessed against interpreted regolith field sites, which yielded approximately 70% similarity for all unit types, as well as against a regolith-geology map interpreted using traditional datasets (not hyperspectral imagery). Importantly, the hyperspectral derived mineral map provided much greater detail enabling a more precise understanding of the regolith-geological architecture where there are exposed soils and rocks.

Morphology and morphometry of upland lakes over lateritic crust, Serra dos Carajás, southeastern Amazon region.

PubMed

Silva, Marcio S DA; Guimarães, José T F; Souza Filho, Pedro W M; Nascimento Júnior, Wilson; Sahoo, Prafulla K; Costa, Francisco R DA; Silva Júnior, Renato O; Rodrigues, Tarcísio M; Costa, Marlene F DA

2018-01-01

High-resolution satellite images, digital elevation models, bathymetric and sedimentological surveys coupled with statistical analysis were used to understand the physical environment and discuss their influence on water quality of the five upland lakes of Serra Sul dos Carajás, southeast Amazonia. The lakes have mid-altitude ranges (elevation), very small (catchment) and shallow to very shallow (central basins). Based on the length, area and volume, Violão and TI (Três Irmãs)-3 lakes may present large vertical movements of the water due to wind action and weakly stratified waters. Trophic conditions based on depth and shore development (Ld) parameters must be used with caution, since Amendoim Lake is relatively deep, but it is oligotrophic to ultra-oligotrophic. Ld values suggest that the lakes are circular to subcircular and are likely formed by solution process, as also suggested by volume development. TI-2 Lake is only presenting convex central basin and has highest dynamic ratio (DR), thus it may have high sedimentation and erosion rates. Based on the relationship between studied parameters, morphometric index and DR likely influence temperature and dissolved oxygen of waters of TI-2 Lake due to its depth profile and wind-induced surface mixing. Nevertheless, water quality parameters are controlled by catchment characteristics of the lakes.

Source and Fate of Sediments in the Bahia de Anasco, Puerto Rico

NASA Astrophysics Data System (ADS)

Webb, R. M.

2005-12-01

Sediments and wastewater mix in the insular marine waters of the Bah'{i}a de Añasco near Mayag{u}ez, Puerto Rico. Trace metal concentrations in fine sediments deposited in the bay were measured to assess potential impact of the ocean outfall on the biota and habitats that include coral reefs. A Q-mode factor analysis of elemental compositions identified three sediment sources and their relative proportions in 51 core and surficial samples collected from the bay and within the coral reefs: (1) sediments discharged by the R'{i}o Grande de Añasco; (2) calcareous skeletal remains; and (3) sediments discharged by the R'{i}o Guanajibo. The nickel and chromium derived from laterite deposits provide a unique fingerprint for sediments discharged from the R'{i}o Guanajibo. Naturally occurring concentrations of these elements exceed Probable Effect Limits (PEL's: 42 mg/kg for nickel and 160 mg/kg for chromium) in sediments deposited near the river mouth. The detection of mercury at 1 mg/kg in one sample from a core recovered near the wastewater outfall was the only indication of a possible outfall source in the data set. The temporal and spatial variations in source fractions proved useful in determining relative frequencies of historic floods and steady-state circulation patterns off the west coast of Puerto Rico.

Importance of a martian hematite site for astrobiology

NASA Technical Reports Server (NTRS)

Allen, C. C.; Westall, F.; Schelble, R. T.

2001-01-01

Defining locations where conditions may have been favorable for life is a key objective for the exploration of Mars. Of prime importance are sites where conditions may have been favorable for the preservation of evidence of prebiotic or biotic processes. Areas displaying significant concentrations of the mineral hematite (alpha-Fe2O3), recently identified by thermal emission spectrometry, may have significance in the search for evidence of extraterrestrial life. Since iron oxides can form as aqueous mineral precipitates, the potential exists to preserve microscopic evidence of life in iron oxide-depositing ecosystems. Terrestrial hematite deposits proposed as possible analogs for hematite deposits on Mars include massive (banded) iron formations, iron oxide hydrothermal deposits, iron-rich laterites and ferricrete soils, and rock varnish. We report the potential for long-term preservation of microfossils by iron oxide mineralization in specimens of the approximately 2,100-Ma banded iron deposit of the Gunflint Formation, Canada. Scanning and analytical electron microscopy reveals micrometer-scale rods, spheres, and filaments consisting predominantly of iron and oxygen with minor carbon. We interpret these objects as microbial cells permineralized by an iron oxide, presumably hematite. The confirmation of ancient martian microbial life in hematite deposits will require the return of samples to terrestrial laboratories. A hematite-rich deposit composed of aqueous iron oxide precipitates may thus prove to be a prime site for future sample return.

Geology of five small Australian impact craters

USGS Publications Warehouse

Shoemaker, E.M.; Macdonald, F.A.; Shoemaker, C.S.

2005-01-01

Here we present detailed geological maps and cross-sections of Liverpool, Wolfe Creek, Boxhole, Veevers and Dalgaranga craters. Liverpool crater and Wolfe Creek Meteorite Crater are classic bowlshaped, Barringer-type craters, Liverpool was likely formed during the Neoproterozoic and was filled and covered with sediments soon thereafter. In the Cenozoic, this cover was exhumed exposing the crater's brecciated wall rocks. Wolfe Creek Meteorite Crater displays many striking features, including well-bedded ejecta units, crater-floor faults and sinkholes, a ringed aeromagnetic anomaly, rim-skirting dunes, and numerous iron-rich shale balls. Boxhole Meteorite Crater, Veevers Meteorite Crater and Dalgaranga crater are smaller, Odessa-type craters without fully developed, steep, overturned rims. Boxhole and Dalgaranga craters are developed in highly follated Precambrian basement rocks with a veneer of Holocene colluvium. The pre-existing structure at these two sites complicates structural analyses of the craters, and may have influenced target deformation during impact. Veevers Meteorite Crater is formed in Cenozoic laterites, and is one of the best-preserved impact craters on Earth. The craters discussed herein were formed in different target materials, ranging from crystalline rocks to loosely consolidated sediments, containing evidence that the impactors struck at an array of angles and velocities. This facilitates a comparative study of the influence of these factors on the structural and topographic form of small impact craters. ?? Geological Society of Australia.

The influence of grain size, grain color, and suspended-sediment concentration on light attenuation: why fine-grained terrestrial sediment is bad for coral reef ecosystems

USGS Publications Warehouse

Storlazzi, Curt; Norris, Benjamin; Rosenberger, Kurt

2015-01-01

Sediment has been shown to be a major stressor to coral reefs globally. Although many researchers have tested the impact of sedimentation on coral reef ecosystems in both the laboratory and the field and some have measured the impact of suspended sediment on the photosynthetic response of corals, there has yet to be a detailed investigation on how properties of the sediment itself can affect light availability for photosynthesis. We show that finer-grained and darker-colored sediment at higher suspended-sediment concentrations attenuates photosynthetically active radiation (PAR) significantly more than coarser, lighter-colored sediment at lower concentrations and provide PAR attenuation coefficients for various grain sizes, colors, and suspended-sediment concentrations that are needed for biophysical modeling. Because finer-grained sediment particles settle more slowly and are more susceptible to resuspension, they remain in the water column longer, thus causing greater net impact by reducing light essential for photosynthesis over a greater duration. This indicates that coral reef monitoring studies investigating sediment impacts should concentrate on measuring fine-grained lateritic and volcanic soils, as opposed to coarser-grained siliceous and carbonate sediment. Similarly, coastal restoration efforts and engineering solutions addressing long-term coral reef ecosystem health should focus on preferentially retaining those fine-grained soils rather than coarse silt and sand particles.

New geological and tectonic map of Paleoproterozoic basement in western Burkina Faso: integrated interpretation of airborne geophysical and field data

NASA Astrophysics Data System (ADS)

Metelka, Vaclav; Baratoux, Lenka; Jessell, Mark; Naba, Seta

2010-05-01

The recent acquisition of regional scale airborne datasets over most of the West African craton sparked off a number of studies concentrating on their litho-tectonic interpretation. In such polydeformed terrains, where outcrop is very sparse or virtually nonexistent due to the presence of thick lateritic cover, geophysics and specifically geomagnetic surveying provide a wealth of information that facilitates the deciphering of regional litho-structural hierarchies. A revised geological and tectonic map of the Houndé and Boromo greenstone belts was derived by interpretation of aeromagnetic and gamma-ray spectrometric data constrained by field observations where available. Medium resolution geophysical data gridded at 250 meters acquired during the SYSMIN project served as a basis for the interpretation. This dataset was integrated with the SRTM digital elevation model and over 600 field observations. Furthermore, the BRGM/BUMIGEB SYSMIN project outcrops database (Castaing et al., 2003) as well as older outcrop maps, maintained by BUMIGEB, were used. Locally, outcrop maps and high resolution geophysics provided by mining companies (Orezone, SEMAFO, Volta Resources, Wega Mining) were employed. 2-D geophysical inversion modeling in GM-sys software using the ground gravity and airborne magnetic data was applied to three selected E-W profiles. Principal component analysis (PCA) of magnetic and radiometric data was a powerful tool for distinguishing different lithological units, in particular tholeiitic suites of basalts and gabbros and various volcano-sedimentary units. Some of the granite pluton limits can be traced as well using the PCA; however thick lateritic cover substantially hinders precise mapping. Magnetic data used on its own gave better results not only for granite limits but also for determining internal structures such as shear zones and concentric compositional zoning. Several major N-S to NNE-SSW oriented shear zones, representing most probably deep crustal structures were identified, some of them previously unreported. The western-most one runs through the eastern margin of the Banfora belt, continues eastwards through to Houndé belt and defines the northern limit of the Boromo belt. Regional stitches of airborne magnetic data at the craton scale show that this structure continues southeastwards to Liberia, attaining over 1000 km. Another shear zone, one of the newly discovered major structures, is NNW-SSE oriented and it affects granitoids between the Banfora and Houndé belts, joining the N-S trending shear zone limiting the Hounde belt in the west. Tarkwaian type metasediments occur as cca 400 km N-S oriented quasi-continuous unit located in the easterly part of the Houndé belt and they are limited on both eastern and western sides by regional scale shear zones. Finally, the Boromo belt is affected along all its length by a connected system of anastomosing subvertical shear zones, some of them representing the limit between the greenstone and granitoids. Additionally, tight isoclinal folds in the Houndé belt indicating E-W compression during the Eburnean orogeny are clearly visible on the PCA image. Interpreted structures are in a good accordance with the meso-scale structures measured in-situ. Castaing, C., Billa, M., Milési, J.P., Thiéblemont, D., Le Mentour, J., Egal, E., Donzeau, M. (BRGM) (coordonnateurs) et Guerrot, C., Cocherie, A., Chevremont, P., Tegyey, M., Itard, Y. (BRGM), Zida, B., Ouedraogo, I., Kote, S., Kabore, B.E., Ouedraogo, C. (BUMIGEB), Ki, J.C., Zunino (ANTEA), 2003. Notice explicative de la Carte géologique et miniére du Burkina Faso à 1/1 000 000.

Distribution and bioavailability of Cr in central Euboea, Greece

NASA Astrophysics Data System (ADS)

Megremi, Ifigeneia

2010-06-01

Plants and soils from central Euboea, were analyzed for Cr(totai), Cr(VI), Ni, Mn, Fe and Zn. The range of metal concentrations in soils is typical to those developed on Fe-Ni laterites and ultramafic rocks. Their bioavailability was expressed in terms of concentrations extractable with EDTA and 1 M HNO3, with EDTA having a limited effect on metal recovery. Cr(VI) concentrations in soils evaluated by alkaline digestion solution were lower than phytotoxic levels. Chromium and Ni — and occasionally Zn — in the majority of plants were near or above toxicity levels. Cr(VI) concentrations in plants were extremely low compared to total chromium concentrations. Cr(total) in ground waters ranged from <1 μg.L-1 to 130 μg.L-1, with almost all chromium present as Cr(VI). With the exception of Cr(total) and in some cases Zn, all elements were below regulatory limits for drinking water. On the basis of Ca, Mg, Cr(total) and Si ground waters were classified into three groups: Group(I) with Cr concentrations less than 1 μg.L-1 from a karstic aquifer; Group(II) with average concentrations of 24 μg.L-1 of Cr and relatively high Si associated with ophiolites; and Group(III) with Cr concentrations of up to 130 μg.L-1, likely due to anthropogenic activity. Group(III) is comparable to ground waters from Assopos basin, characterized by high Cr(VI) concentrations, probably due to industrial actrivities.

Purification and biological evaluation of the metabolites produced by Streptomyces sp. TK-VL_333.

PubMed

Kavitha, Alapati; Prabhakar, Peddikotla; Vijayalakshmi, Muvva; Venkateswarlu, Yenamandra

2010-06-01

An Actinobacterium strain isolated from laterite soils of the Guntur region was identified as Streptomyces sp. TK-VL_333 by 16S rRNA analysis. Cultural, morphological and physiological characteristics of the strain were recorded. The secondary metabolites produced by the strain cultured on galactose-tyrosine broth were extracted and concentrated followed by defatting of the crude extract with cyclohexane to afford polar and non-polar residues. Purification of the two residues by column chromatography led to isolation of five polar and one non-polar fraction. Bioactivity- guided fractions were rechromatographed on a silica gel column to obtain four compounds, namely 1H-indole-3-carboxylic acid, 2,3-dihydroxy-5-(hydroxymethyl) benzaldehyde, 4-(4-hydroxyphenoxy) butan-2-one and acetic acid-2-hydroxy-6-(3-oxo-butyl)-phenyl ester from three active polar fractions and 8-methyl decanoic acid from one non-polar fraction. The structure of the compounds was elucidated on the basis of FT-IR, mass and NMR spectroscopy. The antimicrobial activity of the bioactive compounds produced by the strain was tested against the bacteria and fungi and expressed in terms of minimum inhibitory concentration. Antifungal activity of indole-3-carboxylic acid was further evaluated under in vitro and in vivo conditions. This is the first report of 2,3-dihydroxy-5-(hydroxymethyl) benzaldehyde, 4-(4-hydroxyphenoxy) butan-2-one, acetic acid-2-hydroxy-6-(3-oxo-butyl)-phenyl ester and 8-methyl decanoic acid from the genus Streptomyces. 2010 Elsevier Masson SAS. All rights reserved.

Surface Response to Regional Uplift of Madagascar Reveals Short Wavelength Dynamic Topography

NASA Astrophysics Data System (ADS)

Stephenson, S.; White, N.

2016-12-01

The physiography of Madagascar is characterized by high elevation but low relief topography with 42% of the landscape at an elevation grgeater than 500 m. Eocene marine limestones crop out at an elevation of 400 m, extensive low relief erosion surfaces capped by laterites occur at elevations of up to 2 km, and longitudinal river profiles are disequilibrated. Together, these observations suggest that Madagascar underwent regional uplift in Neogene times. Inverse modeling of drainage networks suggests that regional uplift is diachronous and has occurred on wavelengths of 1000 km. The existence of deeply incised river channels together with low-temperature thermochronologic measurements (i.e. AFT, AHe) implies that erosion occurred in response to regional Neogene uplift. Admittance analysis of long wavelength free-air gravity and topography shows that admittance, Z = 45 ± 5 mGal/km. The history of Neogene volcanism and a lack of significant tectonic shortening both suggest that uplift is dynamically supported. Here we present a suite of U-Th dates of emergent coral reef deposits from northern Madagascar, whose margins are sometimes considered `stable'. Elevation of these coeval coral reefs decreases from 7.2 m at the northern tip of Madagascar to sea level 100 km to the south. The existence of a spatial gradient suggests that differential vertical motions occurred during Late Quaternary times. These results raise significant questions about the reliability both of emergent coral reefs as global sea-level markers and the length-scale of variations in dynamic topography.

The next decade in geochemistry

USGS Publications Warehouse

Ingerson, E.

1958-01-01

The purpose, associations, functions; and activities of the Geochmical Society are reviewed briefly. Work on the Colorado Plateau uranium deposits is described as an example of what geochemical research, in conjunction with detailed field work, mineralogical studies, and related techniques can contribute to the understanding of a type of deposit. It is pointed out that not only have these studies given a great deal of information about the origin of the ores, but they have brought about directly a manifold increase in production and reserves of uranium in the United States. Indirectly, they aided the discovery of the tremendous deposits of the Blind River area in Ontario. It is suggested that similar broad cooperative attacks could not only yield comparable results with other types of mineral deposits, such as laterites and Mississippi Valley type lead-zinc deposits, but could also advance our knowledge and understanding of such diverse problems of geology and cosmology as the origin of granites, origin and geologic implications of meteorites (including tektites), origin and search for petroleum, and geochemical relations and interpretations of natural waters. For each of these problems methods of approach are outlined and for some of them, specific projects and correlative problems are mentioned. It is further suggested that the broad cooperative attack needed for most of these problems might be fostered most effectively by a programme comparable to that of the I.G.Y., even though for most types of geochemical research synoptic sampling and observations are not as important as they are for many projects in geophysics. ?? 1958.

A test of the chromosomal theory of ecotypic speciation in Anopheles gambiae

PubMed Central

Manoukis, Nicholas C.; Powell, Jeffrey R.; Touré, Mahamoudou B.; Sacko, Adama; Edillo, Frances E.; Coulibaly, Mamadou B.; Traoré, Sekou F.; Taylor, Charles E.; Besansky, Nora J.

2008-01-01

The role of chromosomal inversions in speciation has long been of interest to evolutionists. Recent quantitative modeling has stimulated reconsideration of previous conceptual models for chromosomal speciation. Anopheles gambiae, the most important vector of human malaria, carries abundant chromosomal inversion polymorphism nonrandomly associated with ecotypes that mate assortatively. Here, we consider the potential role of paracentric inversions in promoting speciation in A. gambiae via “ecotypification,” a term that refers to differentiation arising from local adaptation. In particular, we focus on the Bamako form, an ecotype characterized by low inversion polymorphism and fixation of an inversion, 2Rj, that is very rare or absent in all other forms of A. gambiae. The Bamako form has a restricted distribution by the upper Niger River and its tributaries that is associated with a distinctive type of larval habitat, laterite rock pools, hypothesized to be its optimal breeding site. We first present computer simulations to investigate whether the population dynamics of A. gambiae are consistent with chromosomal speciation by ecotypification. The models are parameterized using field observations on the various forms of A. gambiae that exist in Mali, West Africa. We then report on the distribution of larvae of this species collected from rock pools and more characteristic breeding sites nearby. Both the simulations and field observations support the thesis that speciation by ecotypification is occurring, or has occurred, prompting consideration of Bamako as an independent species. PMID:18287019

Biomining: metal recovery from ores with microorganisms.

PubMed

Schippers, Axel; Hedrich, Sabrina; Vasters, Jürgen; Drobe, Malte; Sand, Wolfgang; Willscher, Sabine

2014-01-01

Biomining is an increasingly applied biotechnological procedure for processing of ores in the mining industry (biohydrometallurgy). Nowadays the production of copper from low-grade ores is the most important industrial application and a significant part of world copper production already originates from heap or dump/stockpile bioleaching. Conceptual differences exist between the industrial processes of bioleaching and biooxidation. Bioleaching is a conversion of an insoluble valuable metal into a soluble form by means of microorganisms. In biooxidation, on the other hand, gold is predominantly unlocked from refractory ores in large-scale stirred-tank biooxidation arrangements for further processing steps. In addition to copper and gold production, biomining is also used to produce cobalt, nickel, zinc, and uranium. Up to now, biomining has merely been used as a procedure in the processing of sulfide ores and uranium ore, but laboratory and pilot procedures already exist for the processing of silicate and oxide ores (e.g., laterites), for leaching of processing residues or mine waste dumps (mine tailings), as well as for the extraction of metals from industrial residues and waste (recycling). This chapter estimates the world production of copper, gold, and other metals by means of biomining and chemical leaching (bio-/hydrometallurgy) compared with metal production by pyrometallurgical procedures, and describes new developments in biomining. In addition, an overview is given about metal sulfide oxidizing microorganisms, fundamentals of biomining including bioleaching mechanisms and interface processes, as well as anaerobic bioleaching and bioleaching with heterotrophic microorganisms.

The effect of oxidant addition on ferrous iron removal from multi-element acidic sulphate solutions

NASA Astrophysics Data System (ADS)

Mbedzi, Ndishavhelafhi; Ibana, Don; Dyer, Laurence; Browner, Richard

2017-01-01

This study was an investigation on the hydrolytic precipitation of iron from simulated pregnant leach solution (PLS) of nickel laterite atmospheric leaching. The effect of equilibrium pH, temperature and the addition of oxidant on total iron (ferrous (Fe (II)) and ferric (Fe (III)), aluminium and chromium removal was investigated together with the associated nickel and cobalt losses to the precipitate. Systematic variations of the experimental variables revealed ≥99% of the ferric iron can be removed from solution at conditions similar to those used in standard partial neutralisation in zinc and nickel production, pH of 2.5 and temperature less than 100 °C with minimal losses (<0.5%) of both nickel and cobalt. Temperature variation from 55 to 90 °C had no significant effect on the magnitude of Fe (III) precipitation but led to a significant increase in aluminium removal from 67% to 95% and improved the filterability of the precipitates. There was no ferrous iron precipitation even at a pH of 3.75 in the absence of an oxidant with its removal (98%) achieved by oxidative precipitation with oxygen gas at pH 3.5. Unlike Fe (III) precipitation, the operating temperature significantly affects oxidative precipitation of Fe (II). Hence, in practical application, the hydrolytic precipitation and oxidation to remove iron must be operated at 85 °C to ensure both ferrous and ferric iron are precipitated.

Adsorption Mechanisms of Trivalent Gold onto Iron Oxy-Hydroxides: From the Molecular Scale to the Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cances, Benjamin; Benedetti, Marc; Farges, Francois

2007-02-02

Gold is a highly valuable metal that can concentrate in iron-rich exogenetic horizons such as laterites. An improved knowledge of the retention mechanisms of gold onto highly reactive soil components such as iron oxy-hydroxides is therefore needed to better understand and predict the geochemical behavior of this element. In this study, we use EXAFS information and titration experiments to provide a realistic thermochemical description of the sorption of trivalent gold onto iron oxy-hydroxides. Analysis of Au LIII-edge XAFS spectra shows that aqueous Au(III) adsorbs from chloride solutions onto goethite surfaces as inner-sphere square-planar complexes (Au(III)(OH,Cl)4), with dominantly OH ligands atmore » pH > 6 and mixed OH/Cl ligands at lower pH values. In combination with these spectroscopic results, Reverse Monte Carlo simulations were used to constraint the possible sorption sites on the surface of goethite. Based on this structural information, we calculated sorption isotherms of Au(III) on Fe oxy-hydroxides surfaces, using the CD-MUSIC (Charge Distribution - MUlti SIte Complexation) model. The various Au(III)-sorbed species were identified as a function of pH, and the results of these EXAFS+CD-MUSIC models are compared with titration experiments. The overall good agreement between the predicted and measured structural models shows the potential of this combined approach to better model sorption processes of transition elements onto highly reactive solid surfaces such as goethite and ferrihydrite.« less

Adsorption Mechanisms of Trivalent Gold onto Iron Oxy-Hydroxides: From the Molecular Scale to the Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cances, Benjamin; /Marne La Vallee U.; Benedetti, Marc

2006-12-13

Gold is a highly valuable metal that can concentrate in iron-rich exogenetic horizons such as laterites. An improved knowledge of the retention mechanisms of gold onto highly reactive soil components such as iron oxyhydroxides is therefore needed to better understand and predict the geochemical behavior of this element. In this study, we use EXAFS information and titration experiments to provide a realistic thermochemical description of the sorption of trivalent gold onto iron oxy-hydroxides. Analysis of Au L{sub III}-edge XAFS spectra shows that aqueous Au(III) adsorbs from chloride solutions onto goethite surfaces as inner-sphere square-planar complexes (Au(III)(OH,Cl){sub 4}), with dominantly OHmore » ligands at pH > 6 and mixed OH/Cl ligands at lower pH values. In combination with these spectroscopic results, Reverse Monte Carlo simulations were used to constraint the possible sorption sites on the surface of goethite. Based on this structural information, we calculated sorption isotherms of Au(III) on Fe oxy-hydroxides surfaces, using the CD-MUSIC (Charge Distribution--Multi Site Complexation) model. The various Au(III)-sorbed species were identified as a function of pH, and the results of these EXAFS+CD-MUSIC models are compared with titration experiments. The overall good agreement between the predicted and measured structural models shows the potential of this combined approach to better model sorption processes of transition elements onto highly reactive solid surfaces such as goethite and ferrihydrite.« less

Geodynamic and climate controls in the formation of Mio-Pliocene world-class oxidized cobalt and manganese ores in the Katanga province, DR Congo

NASA Astrophysics Data System (ADS)

Decrée, Sophie; Deloule, Étienne; Ruffet, Gilles; Dewaele, Stijn; Mees, Florias; Marignac, Christian; Yans, Johan; de Putter, Thierry

2010-10-01

The Katanga province, Democratic Republic of Congo, hosts world-class cobalt deposits accounting for ~50% of the world reserves. They originated from sediment-hosted stratiform copper and cobalt sulfide deposits within Neoproterozoic metasedimentary rocks. Heterogenite, the main oxidized cobalt mineral, is concentrated as “cobalt caps” along the top of silicified dolomite inselbergs. The supergene cobalt enrichment process is part of a regional process of residual ore formation that also forms world-class “manganese cap” deposits in western Katanga, i.e., the “black earths” that are exploited by both industrial and artisanal mining. Here, we provide constraints on the genesis and the timing of these deposits. Ar-Ar analyses of oxidized Mn ore and in situ U-Pb SIMS measurements of heterogenite yield Mio-Pliocene ages. The Ar-Ar ages suggest a multi-phase process, starting in the Late Miocene (10-5 Ma), when the metal-rich substratum was exposed to the action of meteoric fluids, due to major regional uplift. Further oxidation took place in the Pliocene (3.7-2.3 Ma) and formed most of the observed deposits under humid conditions: Co- and Mn-caps on metal-rich substrata, and coeval Fe laterites on barren areas. These deposits formed prior to the regional shift toward more arid conditions in Central Africa. Arid conditions still prevailed during the Quaternary and resulted in erosion and valley incision, which dismantled the metal-bearing caps and led to ore accumulation in valleys and along foot slopes.

High arsenic groundwater: mobilization, metabolism and mitigation--an overview in the Bengal Delta Plain.

PubMed

Bhattacharyya, Rupa; Chatterjee, Debashis; Nath, Bibhash; Jana, Joydev; Jacks, Gunnar; Vahter, Marie

2003-11-01

The widespread occurrence of high inorganic arsenic in natural waters is attributed to human carcinogen and is identified as a major global public health issue. The scale of the problem in terms of population exposure (36 million) and geographical area coverage (173 x 10(3) Km2) to high arsenic contaminated groundwater (50-3200 microgL(-1)) compared to the National drinking water standard (50 microgL(-1)) and WHO recommended provisional limit (10 microgL(-1)) is greatest in the Holocene alluvium and deltaic aquifers of the Bengal Delta Plain (Bangladesh and West Bengal, India). This large-scale 'natural' high arsenic groundwater poses a great threat to human health via drinking water. Mobilization, metabolism and mitigation issues of high arsenic groundwater are complex and need holistic approach for sustainable development of the resource. Mobilization depends on the redox geochemistry of arsenic that plays a vital role in the release and subsequent transport of arsenic in groundwater. Metabolism narrates the biological response vis-à-vis clinical manifestations of arsenic due to various chemical and biological factors. Mitigation includes alternative source for safe drinking water supply. Drinking water quality regulatory standards as well as guidelines are yet to cover risk assessments for such metal toxicity. Lowering of the ingested inorganic arsenic level and introduction of newer treatment options (implementation of laterite, the natural material) to ensure safe water supply (arsenic free and/or low arsenic within permissible limit) are the urgent need to safe guard the mass arsenic poisoning and internal arsenic related health problems.

[Dr. Moshe Sherman--the first otolaryngologist in Eretz-Israel: 100 years since his arrival].

PubMed

Golz, Avishay; Netzer, Aviram

2012-01-01

On 4.8.1911 Dr. Moshe Sherman landed at the port of Jaffa. He was the first otolaryngologist in Eretz-Israel and for one year he was the only specialist in the country. Dr. Sherman was born in Nikolayev (Russia) in 1881. He started his medical education in Odessa, continued in Berlin, graduated in 1907 at the University of Dorpat (Estonia) and pursued postgraduate studies in otolaryngology at Moscow University. He settled in Jaffa, started a private practice and soon became a famous specialist. He volunteered at the Jewish hospital in Jaffa--"Shaar Zion", and twice a year spent several weeks in Jerusalem seeing patients and performing small operations. On January 1912 Dr. Sherman, together with another 5 physicians, laid the foundations for the first doctors' organization in Israel: "The Medical Society of Jaffa and Jaffa district". In 1918 Dr. Sherman was elected consultant at the Hadassah Hospital in Tel Aviv, and in 1932 a department for ear, nose and throat diseases was established there under his management. He was the founder and first chairman of the Ototaryngology Society in Eretz-Israel, and in 1935 was elected the chairman of the Jewish Medical Association in Eretz-Israel (later--its honorary president). He was the initiator and founder of the "World Fellowship", and the Editor in Chief of 'Harefuah' and "Michtav Lachaver". Dr. Sherman was the author of numerous papers related to his specialty and to the history of Jewish organizations in Eretz-Israel and, later, in the State of Israel. Dr. Sherman died in Tel Aviv on July 17th 1969.

Classifying zones of suitability for manual drilling using textural and hydraulic parameters of shallow aquifers: a case study in northwestern Senegal

NASA Astrophysics Data System (ADS)

Fussi, F. Fabio; Fumagalli, Letizia; Fava, Francesco; Di Mauro, Biagio; Kane, Cheik Hamidou; Niang, Magatte; Wade, Souleye; Hamidou, Barry; Colombo, Roberto; Bonomi, Tullia

2017-12-01

A method is proposed that uses analysis of borehole stratigraphic logs for the characterization of shallow aquifers and for the assessment of areas suitable for manual drilling. The model is based on available borehole-log parameters: depth to hard rock, depth to water, thickness of laterite and hydraulic transmissivity of the shallow aquifer. The model is applied to a study area in northwestern Senegal. A dataset of boreholes logs has been processed using a software package (TANGAFRIC) developed during the research. After a manual procedure to assign a standard category describing the lithological characteristics, the next step is the automated extraction of different textural parameters and the estimation of hydraulic conductivity using reference values available in the literature. The hydraulic conductivity values estimated from stratigraphic data have been partially validated, by comparing them with measured values from a series of pumping tests carried out in large-diameter wells. The results show that this method is able to produce a reliable interpretation of the shallow hydrogeological context using information generally available in the region. The research contributes to improving the identification of areas where conditions are suitable for manual drilling. This is achieved by applying the described method, based on a structured and semi-quantitative approach, to classify the zones of suitability for given manual drilling techniques using data available in most African countries. Ultimately, this work will support proposed international programs aimed at promoting low-cost water supply in Africa and enhancing access to safe drinking water for the population.

Alteration mineral mapping for iron prospecting using ETM+ data, Tonkolili iron field, northern Sierra Leone

NASA Astrophysics Data System (ADS)

Mansaray, Lamin R.; Liu, Lei; Zhou, Jun; Ma, Zhimin

2013-10-01

The Tonkolili iron field in northern Sierra Leone has the largest known iron ore deposit in Africa. It occurs in a greenstone belt in an Achaean granitic basement. This study focused mainly on mapping areas with iron-oxide and hydroxyl bearing minerals, and identifying potential areas for haematite mineralization and banded iron formations (BIFs) in Tonkolili. The predominant mineral assemblage at the surface (laterite duricrust) of this iron field is haematitegoethite- limonite ±magnetite. The mineralization occurs in quartzitic banded ironstones, layered amphibolites, granites, schists and hornblendites. In this study, Crosta techniques were applied on Enhanced Thematic Mapper (ETM+) data to enhance areas with alteration minerals and target potential areas of haematite and BIF units in the Tonkolili iron field. Synthetic analysis shows that alteration zones mapped herein are consistent with the already discovered magnetite BIFs in Tonkolili. Based on the overlaps of the simplified geological map and the remote sensing-based alteration mineral maps obtained in this study, three new haematite prospects were inferred within, and one new haematite prospect was inferred outside the tenement boundary of the Tonkolili exploration license. As the primary iron mineral in Tonkolili is magnetite, the study concludes that, these haematite prospects could also be underlain by magnetite BIFs. This study also concludes that, the application of Crosta techniques on ETM+ data is effective not only in mapping iron-oxide and hydroxyl alterations but can also provide a basis for inferring areas of potential iron resources in Algoma-type banded iron formations (BIFs), such as those in the Tonkolili field.

Detection of hydrocarbon microseepage in a rain forest environment (Jurua Gas field, northern Brazil) using Landsat MSS data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miranda, F.P.; Cunha, F.M.B.

1990-05-01

The Jurua gas field is the first important hydrocarbon accumulation found in the jungle-covered Solimoes basin. The tectonic framework in this area is characterized by a right-lateral transpressional zone (Jurua structural trend). Hydrocarbon traps are anticlines developed along the upthrown block of a reverse fault. The prospective 2,200-m-thick Paleozoic section is unconformably covered by a 2,800-m-thick pile of Mesozoic and Cenozoic continental sediments. Anomalous concentrations of hydrocarbons (C{sub 2}-C{sub 4}) in soil samples are concordantly aligned with the trace of the reverse fault crossing the gas field, indicating that this feature acted as a conduit for hydrocarbon microseepage. Gas-producing wellsmore » are located over a tabular watershed which coincides with the northeast-southwest Jurua structural trend. An unsupervised classification of Landsat MSS data over the gas field area reveals that one spectral class of vegetation is aligned with the Jurua structural trend. Field checking shows that the vegetation near the gas-producing well 1-JR-1-AM is not as dense as the forest outside the limits of the Jurua gas field. Two geologic factors may account for the vegetation anomaly over the gas field. (1) The northeast-southwest tabular watershed corresponds to a Pleistocene erosional surface associated with weathering products such as bauxite and laterite. The resulting soil is impermeable and low in nutrients. (2) The spectral behavior of vegetation may represent the response of plants to long-term anaerobic soil conditions brought about by gas leakage from the Paleozoic reservoir.« less

Sediment pollution impacts sensory ability and performance of settling coral-reef fish.

PubMed

O'Connor, J Jack; Lecchini, David; Beck, Hayden J; Cadiou, Gwenael; Lecellier, Gael; Booth, David J; Nakamura, Yohei

2016-01-01

Marine organisms are under threat globally from a suite of anthropogenic sources, but the current emphasis on global climate change has deflected the focus from local impacts. While the effect of increased sedimentation on the settlement of coral species is well studied, little is known about the impact on larval fish. Here, the effect of a laterite "red soil" sediment pollutant on settlement behaviour and post-settlement performance of reef fish was tested. In aquarium tests that isolated sensory cues, we found significant olfaction-based avoidance behaviour and disruption of visual cue use in settlement-stage larval fish at 50 mg L(-1), a concentration regularly exceeded in situ during rain events. In situ light trap catches showed lower abundance and species richness in the presence of red soil, but were not significantly different due to high variance in the data. Prolonged exposure to red soil produced altered olfactory cue responses, whereby fish in red soil made a likely maladaptive choice for dead coral compared to controls where fish chose live coral. Other significant effects of prolonged exposure included decreased feeding rates and body condition. These effects on fish larvae reared over 5 days occurred in the presence of a minor drop in pH and may be due to the chemical influence of the sediment. Our results show that sediment pollution of coral reefs may have more complex effects on the ability of larval fish to successfully locate suitable habitat than previously thought, as well as impacting on their post-settlement performance and, ultimately, recruitment success.

Groundwater vulnerability assessment using hydrogeologic and geoelectric layer susceptibility indexing at Igbara Oke, Southwestern Nigeria

NASA Astrophysics Data System (ADS)

Oni, T. E.; Omosuyi, G. O.; Akinlalu, A. A.

2017-12-01

Groundwater vulnerability assessment was carried out at Igbara Oke Southwestern Nigeria, with a view to classify the area into vulnerability zones, by applying the electrical resistivity method, using Schlumberger electrode arrays with maximum electrode separation (AB/2) of 65 m in (41) different locations for data acquisition. Geoelectric parameters (layer resistivity and thickness) were determined from the interpreted data. The study area comprises four geoelectric layers (topsoil, lateritic layer, weathered/fractured layer and fresh basement). The geoelectric parameters of the overlying layers across the area were used to assess the vulnerability of the underlying aquifers to near-surface contaminants with the aid of vulnerability maps generated. Three models were compared by maps using geo-electrically derived models; longitudinal conductance, GOD (groundwater occurrence, overlying lithology and depth to the aquifer) and GLSI (geoelectric layer susceptibility indexing). The total longitudinal conductance map shows the north central part of the study area as a weakly protected (0.1-0.19) area, while the northern and southern parts have poor protective capacity (<0.1); this is in agreement with the GOD method which shows the northern part of the study area as less vulnerable (0-0.1) while the southern part has low/moderate (0.1-0.3) vulnerability to contamination. The longitudinal conductance exaggerates the degree of susceptibility to contamination than the GOD and GLSI models. From the models, vulnerability to contamination can be considered higher at the southern part than the northern part and therefore, sources of contamination like septic tank, refuse dump should be cited far from groundwater development area.

Cenozoic Source-to-Sink of the African margin of the Equatorial Atlantic

NASA Astrophysics Data System (ADS)

Rouby, Delphine; Chardon, Dominique; Huyghe, Damien; Guillocheau, François; Robin, Cecile; Loparev, Artiom; Ye, Jing; Dall'Asta, Massimo; Grimaud, Jean-Louis

2016-04-01

The objective of the Transform Source to Sink Project (TS2P) is to link the dynamics of the erosion of the West African Craton to the offshore sedimentary basins of the African margin of the Equatorial Atlantic at geological time scales. This margin, alternating transform and oblique segments from Guinea to Nigeria, shows a strong structural variability in the margin width, continental geology and relief, drainage networks and subsidence/accumulation patterns. We analyzed this system combining onshore geology and geomorphology as well as offshore sub-surface data. Mapping and regional correlation of dated lateritic paleo-landscape remnants allows us to reconstruct two physiographic configurations of West Africa during the Cenozoic. We corrected those reconstitutions from flexural isostasy related to the subsequent erosion. These geometries show that the present-day drainage organization stabilized by at least 29 Myrs ago (probably by 34 Myr) revealing the antiquity of the Senegambia, Niger and Volta catchments toward the Atlantic as well as of the marginal upwarp currently forming a continental divide. The drainage rearrangement that lead to this drainage organization was primarily enhanced by the topographic growth of the Hoggar swell and caused a major stratigraphic turnover along the Equatorial margin of West Africa. Elevation differences between paleo-landscape remnants give access to the spatial and temporal distribution of denudation for 3 time-increments since 45 Myrs. From this, we estimate the volumes of sediments and associated lithologies exported by the West African Craton toward different segments of the margin, taking into account the type of eroded bedrock and the successive drainage reorganizations. We compare these data to Cenozoic accumulation histories in the basins and discuss their stratigraphic expression according to the type of margin segment they are preserved in.

Mineral potential for nickel, copper, platinum group elements(PGE), and chromium deposits hosted in ultramafic rocks in the Islamic Republic of Mauritania (phase V, deliverable 67): Chapter G in Second projet de renforcement institutionnel du secteur minier de la République Islamique de Mauritanie (PRISM-II)

USGS Publications Warehouse

Taylor, Cliff D.; Marsh, Erin; Anderson, Eric D.

2015-01-01

PRISM-I summary documents mention the presence of mafic-ultramafic igneous intrusive rocks in several areas of Mauritania and a number of chromium (Cr) and copper-nickel (Cu-Ni (±Co, Au)) occurrences associated with them. Permissive geologic settings generally include greenstone belts of any age, layered mafic-ultramafic and unlayered gabbro-anorthosite intrusive complexes in cratonic settings, ophiolite complexes, flood basalt provinces, and fluid-rich shear zones cutting accumulations of mafic-ultramafic rocks. Regions of Mauritania having these characteristics that are discussed in PRISM-I texts include the Mesoarchean greenstone belts of the TasiastTijirit terrane in the southwestern Rgueïbat Shield, two separate layered ultramafic complexes in the Amsaga Complex west of Atar, serpentinized metadunites in Mesoarchean rocks of the Rgueïbat Shield in the Zednes map sheet, several lateritized annular mafic-ultramafic complexes in the Paleoproterozoic northwestern portion of the Rgueïbat Shield, and the serpentinized ophiolitic segments of the Gorgol Noir Complex in the axial portion of the southern Mauritanides. Bureau de Recherches Géologiques et Minières (BRGM) work in the “Extreme Sud” zone also suggests that small copper occurrences associated with the extensive Jurassic microgabbroic intrusive rocks in the Taoudeni Basin of southeastern Mauritania could have potential for magmatic Cu-Ni (PGE, Co, Au) sulfide mineralization. Similarly, Jurassic mafic intrusive rocks in the northeastern Taoudeni Basin may be permissive. Known magmatic Cu-Ni deposits of these types in Mauritania are few in number and some uncertainty exists as to the nature of several of the more important ones.

Investigation of groundwater in parts of Ndokwa District in Nigeria using geophysical logging and electrical resistivity methods: Implications for groundwater exploration

NASA Astrophysics Data System (ADS)

Anomohanran, Ochuko; Ofomola, Merrious Oviri; Okocha, Fredrick Ogochukwu

2017-05-01

Groundwater study involving the application of geophysical logging and vertical electrical sounding (VES) methods was carried out in parts of Ndokwa area of Delta State, Nigeria. The objective was to delineate the geological situation and the groundwater condition of the area. The geophysical logging of a drilled well and thirty VESs of the Schlumberger configuration were executed in this study using the Abem SAS 1000/4000 Terrameter. The result of the lithological study from the drilled well showed that the subsurface formation consist of lateritic topsoil, very fine sand, clayey fine sand, fine and medium grain sand, coarse sand, medium coarse sand and very coarse sand. The interpretation of the vertical electrical sounding data using a combination of curve matching and Win Resist computer iteration showed a close correlation with the well record. The result revealed the presence of four geoelectric layers with the aquifer identified to be in the fourth layer and having resistivity which ranged from 480 to 11,904 Ωm, while the depth ranged between 17.8 and 38.8 m. The analysis of the geophysical logging revealed that the average value of the electrical conductivity and the total dissolved solid of the groundwater in the aquifer were obtained as 229 μS/cm and 149 mg/cm3 respectively. These results indicate that the groundwater is within the permissible limit set by the Standard Organization of Nigeria for potable water which is 1000 μS/cm for electrical conductivity and 500 mg/cm3 for total dissolved solid. The fourth layer was therefore identified as the potential non conductive zone suitable for groundwater development in the study area.

A review of nickel toxicity to marine and estuarine tropical biota with particular reference to the South East Asian and Melanesian region.

PubMed

Gissi, Francesca; Stauber, Jennifer L; Binet, Monique T; Golding, Lisa A; Adams, Merrin S; Schlekat, Christian E; Garman, Emily R; Jolley, Dianne F

2016-11-01

The South East Asian Melanesian (SEAM) region contains the world's largest deposits of nickel lateritic ores. Environmental impacts may occur if mining operations are not adequately managed. Effects data for tropical ecosystems are required to assess risks of contaminant exposure and to derive water quality guidelines (WQG) to manage these risks. Currently, risk assessment tools and WQGs for the tropics are limited due to the sparse research on how contaminants impact tropical biota. As part of a larger project to develop appropriate risk assessment tools to ensure sustainable nickel production in SEAM, nickel effects data were required. The aim of this review was to compile data on the effects of nickel on tropical marine, estuarine, pelagic and benthic species, with a particular focus on SEAM. There were limited high quality chronic nickel toxicity data for tropical marine species, and even fewer for those relevant to SEAM. Of the data available, the most sensitive SEAM species to nickel were a sea urchin, copepod and anemone. There is a significant lack of high quality chronic data for several ecologically important taxonomic groups including cnidarians, molluscs, crustaceans, echinoderms, macroalgae and fish. No high quality chronic nickel toxicity data were available for estuarine waters or marine and estuarine sediments. The very sparse toxicity data for tropical species limits our ability to conduct robust ecological risk assessment and may require additional data generation or read-across from similar species in other databases (e.g. temperate) to fill data gaps. Recommendations on testing priorities to fill these data gaps are presented. Copyright © 2016 Elsevier Ltd. All rights reserved.

Topographic growth around the Orange River valley, southern Africa: A Cenozoic record of crustal deformation and climatic change

NASA Astrophysics Data System (ADS)

Dauteuil, Olivier; Bessin, Paul; Guillocheau, François

2015-03-01

We reconstruct the history of topographic growth in southern Africa on both sides of the Orange River valley from an integrated analysis of erosion surfaces, crustal deformation and climate change. First, we propose an inventory of erosion surfaces observed in the study area and classify them according to their most likely formative process, i.e. chemical weathering or mechanical erosion. Among the various land units observed we define a new class of landform: the pedivalley, which corresponds to a wide valley with a flat erosional floor. In the Orange River valley, we mapped three low-relief erosion surfaces, each bevelling a variety of lithologies. The oldest and most elevated is (1) a stripped etchplain evolving laterally into (2) a stepped pediplain bearing residual inselbergs; (3) a younger pediplain later formed in response to a more recent event of crustal deformation. These are all Cenozoic landforms: the etchplain is associated with a late Palaeocene to middle Eocene weathering event, and the two pediplains are older than the middle Miocene alluvial terraces of the Orange River. Landscape evolution was first driven by slow uplift (10 m/Ma), followed by a second interval of uplift involving a cumulative magnitude of at least 200 m. This event shaped the transition between the two pediplains and modified the drainage pattern. A final phase of uplift (magnitude: 60 m) occurred after the Middle Miocene and drove the incision of the lower terraces of the Orange River. Climate exerted a major control over the denudation process, and involved very humid conditions responsible for lateritic weathering, followed by more arid conditions, which promoted the formation of pedivalleys. Collectively, these produce pediplains.

Internal dose assessment of 238U contaminated soils based on in-vitro gastrointestinal protocol

NASA Astrophysics Data System (ADS)

Perama, Yasmin Mohd Idris; Rashid, Nur Shahidah Abdul; Majid, Amran Ab.; Siong, Khoo Kok

2017-01-01

Human exposure to natural radioactive uranium has been a great interest as more industrial rapidly growing contributes to radiation risks. The aim of this case study was to determine the internal dose in humans incorporated with ingestion of 238U contaminated soils. A gastrointestinal analogue test was employed to simulate the human digestive tract. In-vitro approach via German DIN 19738 model was developed in order to estimate the internal exposure of 238U due to ingestion of different types of soils. Synthetic gastrointestinal fluids assay via in-vitro method were produced to determine the concentration of 238U in various soils using ICP-MS. Based on the results, concentration of 238U in BRIS, laterite, peat and alluvium soils were in ranged between (0.0061 ± 0.0057 - 0.0488 ± 0.0148) ppm and (0.0005 ± 0.0004 - 0.0046 ± 0.0007) ppm in gastric and gastrointestinal phase respectively. Types of soil compositions and pH medium were some of the factors that influence mobilization and solubility of 238U contaminanted soil into the digestive juices that resembles human gastrointestinal tract. For the purpose of internal dose assessment, the committed efective dose from 238U intake in soils ranged between 1.237 × 10-11 - 9.8993 × 10-11 Sv y-1 for gastric phase and 1.0184 × 10-12 - 9.3294 × 10-12 Sv y-1 for gastric-intestinal phase. The internal dose measurements from this study were much lower from the recommended values. Hence, ingestion of 238U contaminated soils would not be expected to pose major health risk to humans.

Electrical Resistivity Studies Between Subarnarekha And Kansabati Rivers, Paschim Medinipur (W.B.), India: Implication To Groundwater Problems In The Area.

NASA Astrophysics Data System (ADS)

Panda, K. P.; Jha, M. K.; Sharma, S. P.

2017-12-01

Various parts of the world face acute shortage of groundwater. To solve groundwater problems various approaches are followed. Interlinking of the river is one of the approaches. The southern part of the West Bengal province of India receives huge amount of rainfall (annual 1200mm). Instead of huge amount of rainfall some parts of the area are problematic for groundwater occurrence. Characterization of aquifer in this area is very important for sustainable development of water supply and artificial recharge schemes. Electrical resistivity survey was performed at regular interval from Kharagpur (north) to Subarnrekha River (south) to map the lithological variations in this area. It covers around 25 kilometers distance from Kharagpur with latitude and longitude (22°19'7.3"N 87°18'40"E) to Subarnrekha River (22°15'49.4" N 87°16'45.1" E). To locating a suitable area for artificial recharge and for the characterization of aquifers vertical electrical sounding is a robust method. Resistivity soundings were carried out with an interval of 2 to 3 kilometers. Subsurface resistivity distribution has been interpreted by using very fast simulated annealing (VFSA) global optimization technique. The study reveals that northern part of the area is problematic and does not have suitable aquifer systems. Resistivity distribution is suitable in the southern part of area and corresponds to clayey sand. Interpreted resistivity in the northern part of the area is relatively high and reveals impervious laterite layer. In southern part of the area resistivity varies between 5-10 Ohm-m at depth below 80 m. Based on the resistivity model different types of geologic units are classified and the zone of interests for aquifer has been demarcated.

Geochemical characterization of the largest upland lake of the Brazilian Amazonia: Impact of provenance and processes

NASA Astrophysics Data System (ADS)

Sahoo, Prafulla Kumar; Guimarães, José Tasso Felix; Souza-Filho, Pedro Walfir Martins; da Silva, Marcio Sousa; Nascimento, Wilson, Júnior; Powell, Mike A.; Reis, Luiza Santos; Pessenda, Luiz Carlos Ruiz; Rodrigues, Tarcísio Magevski; da Silva, Delmo Fonseca; Costa, Vladimir Eliodoro

2017-12-01

Lake Três Irmãs (LTI), the largest upland lake in the Brazilian Amazonia, located in Serra dos Carajás, was characterized using multi-elemental and isotope geochemistry (δ13C and δ15N) to understand the significance of organic and inorganic sources, weathering and sedimentary processes on the distribution of elements in lake bottom (surficial) sediments. Carbon and nitrogen isotopes from sedimentary organic matter suggest C3 terrestrial plants (forests > canga vegetation), macrophytes and freshwater DOC as the main sources. Sediments are depleted in most of the major oxides (except Fe2O3 and P2O5) when compared to upper continental crust (UCC) and their spatial distribution is highly influenced by catchment lithology. Principal Component Analysis revealed that most of the trace elements (Ba, Sr, Rb, Sc, Th, U, Zr, Hf, Nb, Y, V, Cr, Ga, Co, Ni) and REEs are closely correlated with Al and Ti (PC1; Group-1), so their redistribution is less influenced by post-depositional process. This is due to their relative immobility and being hosted by Al-bearing minerals during laterization. High Chemical Index of Alteration (CIA), Mafic Index of Alteration (MIA) and Index of Laterization (IOL) values indicate intense chemical weathering at source areas, but the weathering transformation was better quantified by IOL. A-CN-K plot along with elemental ratios (Al/K, Ti/K, Ti/Zr, La/Al, Cr/Th, Co/Th, La/Sm, La/Gd, Zr/Y, and Eu/Eu*) as well as chondrite-normalized REE patterns show that the detritic sediments are mainly sourced from ferruginous laterites and soils in the catchment, which may have characteristics similar to mafic rocks.

Medical geology of endemic goiter in Kalutara, Sri Lanka; distribution and possible causes.

PubMed

Fernando, G W A R; Liyanage, P L C L; Rajapaksha, Anushka Upamali; Vithanage, Meththika

2017-12-01

This study assesses the distribution of goiter in the Kalutara District, Sri Lanka in order to find causative factors for the occurrence of goiter even after the salt iodization. A questionnaire survey was conducted at the household level and at the same time iodine and selenium levels of the water sources were analyzed. Questionnaire survey results indicated the highest numbers of goiter patients in the northern part where the lowest were found in the southern sector which may be due to the presence of acid sulfate soils. Females were more susceptible and it even showed a transmittance between generations. Average iodine concentrations in subsurface water of goiter endemic regions are 28.25 ± 15.47 μg/L whereas non-goiter regions show identical values at 24.74 ± 18.29 μg/L. Surface water exhibited relatively high values at 30.87 ± 16.13 μg/L. Endemic goiter was reported in some isolated patches where iodine and selenium concentrations low, latter was <10 μg/L. The formation of acid sulfate soils in the marshy lands in Kalutara district may lead to transformation of biological available iodine oxidation into volatile iodine by humic substances, at the same time organic matter rich peaty soil may have strong held of iodine and selenium which again induced by low pH and high temperature were suggested as the instrumental factors in the endemic goiter in Kalutara district. Hence, geochemical features such as soil pH, organic matter and thick lateritic cap in the Kalutara goiter endemic area play a role in controlling the available selenium and iodine for food chain through plant uptake and in water.

Origin of the lethal gas burst from Lake Monoun, Cameroun

NASA Astrophysics Data System (ADS)

Sigurdsson, H.; Devine, J. D.; Tchua, F. M.; Presser, F. M.; Pringle, M. K. W.; Evans, W. C.

1987-03-01

On 15 August, 1984, a lethal gas burst issued from a submerged 96-m-deep crater in Lake Monoun in Cameroun, western Africa, killing 37 people. The event was associated with a landslide from the eastern crater rim, which slumped into deep water. Waters below 50 m are anoxic, dominated by high Fe 2+ (˜600 mg/l) and HCO 3- (≥ 1900 mg/l), anoxic and supersaturated with siderite, which is a major component of the crater floor sediments. The unusually high Fe 2+ levels are attributed to reduction of laterite-derived ferric iron gradually brought into the lake as loess and in river input. Sulfur compounds are below detection limits in both water and gas. Gases effervescing from depressurized deep waters are dominantly CO 2 with minor CH 4, having δ 13C of -7.18 and -54.8 per mil, respectively. Bacterial decomposition of organic matter may account for the methane, but 14C of lake water indicates that only 10% of the carbon is modern, giving an apparent age of 18,000 years. The dominant source of carbon is therefore attributed to long-term emission of CO 2 as volcanic exhalation from vents within the crater, which led to gradual build-up of HCO 3- in the lake. The density stratification of the lake may have been upset by an earthquake and underwater landslide on 15 August, which triggered overturn of the lake and caused nucleation of CO 2 in the deep water. The resultant ebullition of CO 2 from deep lake waters led to a gas burst at the surface and locally generated a water wave up to 5 m high. People travelling through the gas cloud were asphyxiated, presumably from CO 2, and suffered skin discoloration from unidentified components.

Origin of the lethal gas burst from Lake Monoun, Cameroun

USGS Publications Warehouse

Sigurdsson, Haraldur; Devine, J.D.; Tchua, F.M.; Presser, F.M.; Pringle, M.K.W.; Evans, William C.

1987-01-01

On 15 August, 1984, a lethal gas burst issued from a submerged 96-m-deep crater in Lake Monoun in Cameroun, western Africa, killing 37 people. The event was associated with a landslide from the eastern crater rim, which slumped into deep water. Waters below 50 m are anoxic, dominated by high Fe2+ (???600 mg/l) and HCO3- (??? 1900 mg/l), anoxic and supersaturated with siderite, which is a major component of the crater floor sediments. The unusually high Fe2+ levels are attributed to reduction of laterite-derived ferric iron gradually brought into the lake as loess and in river input. Sulfur compounds are below detection limits in both water and gas. Gases effervescing from depressurized deep waters are dominantly CO2 with minor CH4, having ??13C of -7.18 and -54.8 per mil, respectively. Bacterial decomposition of organic matter may account for the methane, but 14C of lake water indicates that only 10% of the carbon is modern, giving an apparent age of 18,000 years. The dominant source of carbon is therefore attributed to long-term emission of CO2 as volcanic exhalation from vents within the crater, which led to gradual build-up of HCO3- in the lake. The density stratification of the lake may have been upset by an earthquake and underwater landslide on 15 August, which triggered overturn of the lake and caused nucleation of CO2 in the deep water. The resultant ebullition of CO2 from deep lake waters led to a gas burst at the surface and locally generated a water wave up to 5 m high. People travelling through the gas cloud were asphyxiated, presumably from CO2, and suffered skin discoloration from unidentified components. ?? 1987.

Short-lived U and Th isotope distribution in a tropical laterite derived from granite (Pitinga river basin, Amazonia, Brazil): Application to assessment of weathering rate

NASA Astrophysics Data System (ADS)

Mathieu, D.; Bernat, M.; Nahon, D.

1995-12-01

We have analyzed samples of a 15 m thick profile weathered from the Madeira granite, located in the Pitinga basin river, north of Manaus, in the state of Amazonia, Brazil. This profile consists essentially of a yellow-red saprolite covered by a soil. U and Th concentrations are particularly high in the granite (20 and 80 μg/g respectively). Normalized element to Th concentrations indicate that Th is most resistant to chemical weathering, except to some extent in the top soil. Higher concentrations in the saprolite compared to the granite comprise a relative enrichment, resulting from a loss of mass. The saprolites are initially generated by a descending weathering front which alters the granite to a yellow-red saprolite, a second front, close to the top, turns the saprolite into a soil. Weathering has led to leaching of U. The 234U/ 238U and 230Th/ 238U isotopic ratios are in radioactive disequilibrium. Numerous nodules are present and apparently started to form at the base of the saprolite. These nodules achieve more developed form during their relative ascent until they are reached by the descending top front where they undergo dissolution. The Th and Pb are concentrated in the nodules close to the top front. The U, being more mobile, is strongly leached by the first front, and most of the remainder, freed by the second, engages in a descending flux which supplies the underlying saprolite. Using the data an attempt is made to model the isotopic distribution in the profile. We conclude that the first front has descended at a rate of 5 cm/1000 yt, and that the time needed to create the saprolite must have been around 300,000 yr.

Nickel and manganese transfer from soil to plant in lateritic mining soils from New Caledonia

NASA Astrophysics Data System (ADS)

Pouschat, P.; Rose, J.; Alliot, I.; Dominici, C.; Keller, C.; Laffont-Schwob, I.; Olivi, L.; Ambrosi, J.-P.

2009-04-01

New Caledonian ferritic soils (more than 50 % of iron) are naturally rich in metals (chromium, nickel, cobalt, and manganese), deficient in major nutrients (nitrogen, phosphorous, and potassium), and unbalanced for the calcium/magnesium ratio. Under these particular ecological conditions, New Caledonia, recognized as a hot-spot of biodiversity, is a natural laboratory to study and understand the adaptation strategies of plants to metalliferous soils, and particularly the tolerance and (hyper)accumulation of metals by plants. Moreover, understanding such mechanisms is essential to develop rehabilitation or phytoremediation techniques for polluted soils, as well as phytomining techniques. Thus, in order to understand the soil - plant relationship and metal mobility along a toposequence in a future nickel mining massif, field experiments were conducted in an isolated ultramafic massif of New Caledonia. Several plant species of two endemic and frequent plant genera were chosen: Tristaniopsis guillainii and T. calobuxus (Myrtaceae), and Phyllanthus serpentinus and P. favieri (Euphorbiaceae), because of their nickel and/or manganese accumulating or hyperaccumulating nature. Leaves, twigs, and roots of all plants were collected along the soil sequence and their associated rhizospheric and bulk soils were sampled. Next, a series of characterization techniques were adapted and then coupled to cryogenics. The combined use of those multiple techniques (cryo-microtomy, cryo-SEM, µXRF, cryo-XAS, and soil characterization) allowed to study co-location and speciation of nickel and manganese in the different plant organs and soils (rhizospheric and bulk). Bioaccumulated nickel and manganese had different distribution patterns. In leaves, Ni accumulated in non photosynthetic tissues (e.g. epidermis) whereas Mn preferentially accumulated in mesophyll whatever the plant species. Nevertheless, in spite of a different speciation in soils, nickel and manganese were both found as similar divalent organometallic complexes in the different plant parts.

Diamonds from the Espinhaço Range (Minas Gerais, Brazil) and their redistribution through the geologic record

NASA Astrophysics Data System (ADS)

Chaves, M. L. S. C.; Karfunkel, J.; Hoppe, A.; Hoover, D. B.

2001-07-01

Diamond-bearing deposits from the Espinhaço Range are associated with three distinct periods in the geologic record. During a Precambrian magmatic period (≥1.75 Ga), diamondiferous rocks were introduced into the crust; the location of these rocks remains an enigma. During a second period, diamonds were eroded from the primary rocks and deposited in the Mesoproterozoic Espinhaço basin (≅1.75-1.70 Ga), where several generations of reworking and diagenisis are suggested. The third period is the Phanerozoic, during which several more episodes of reworking occurred. The first was during the Eocretaceous uplift of the range, when Precambrian conglomerates were partially eroded and diamonds redeposited in fluvial systems. These deposits have little economic significance because of overlying Tertiary laterites. Renewed upheaval at the Neogene formed diamondiferous fanglomeratic deposits as a result of the pronounced relief. Quaternary climate cycling developed colluvial deposits on earlier formed occurrences. Fanglomeratic and colluvial deposits are worked where the adjacent Proterozoic or Cretaceous sources produced widespread diamond-bearing gravels. Finally, recent river systems have reworked all the earlier sources to produce economic gravels in some places. Although these recent gravels are low grade, they are a major diamond source because of the large reserves. The mineralogical characteristics of these diamonds reflect the long history and repeated reworking of the source deposits, and the geologic history of the region points towards an extra-basinal source area, probably to the west within the São Francisco Craton. This repeated reworking has resulted in a natural selection of the diamonds that eliminated low-quality stones in the journey to their final resting place.

Significance of the giant Lower Cretaceous paleoweathering event

NASA Astrophysics Data System (ADS)

Thiry, Médard; Ricordel-Prognon, Caroline; Schmitt, Jean-Michel

2010-05-01

Weathering profiles typically develop at the interface with the atmosphere, and thus, record the fluctuations in the paleoatmosphere's chemistry and climatic conditions. Consequently they are one of the main archives to upgrade our understanding on paleoclimate and the Earth's environmental history. In this presentation, we will focus on the linking between paleoatmosphere compositions, weathering rates, and their impact on the subsequent sedimentary records. Distribution of the Lower Cretaceous lateritic weathering facies. During the Early Cretaceous, sea level drops and wide exondations lead to development of deep "lateritic" weathering profiles. Thick kaolinitic weathering profiles occured on the Hercynian basements and diverse kaolinitic and ferruginous weathering products covered the Jurassic limestone platforms. This major lateritic event is not restricted to Europe but also well know in North-America (up to Canada), South-America (down to Argentina), and in Australia. Moreover, recent paleomagnetic and radiometric datations revealed that numerous kaolinitic and ferruginous formations, which classically were ascribed to Tertiary ages, date back to the Lower Cretaceous period (Thiry et al., 2006). Additionally, the Bonherz iron ore deposits in the paleokarsts of the Jurassic limestone plateform of the Paris Basin also have to be reconsidered as of Cretaceous age, probably as well as the Tertiary age of the Swiss and Bavarian Jura Bonherz. Paleoclimatic interpretation. During a long time, the interpretation of these paleoweathering features has been a major palaeoclimatic argument. The spreading out of deep kaolinitic weathering profiles (from the Scandinavian and Canadian shields to southern Argentina and Australia, which was still situated close to Antarctica at that time) has lead to considerations, that during this period a warm and wet climate prevailed globally, with very little latitudinal differentiation. These paleoclimatic interpretations stand in contradiction to the paleobotanical data and the interpretation of the glacial origin of some sedimentary figures, such as dropstones. Additionally, some isotopic data are contradictory to the hypothesis of a warm climate around the whole world; in fact the data indicate cold water masses or even glaciation at high latitudes (Bornemann, 2008). On the other hand, numerous paleontological as well as some isotopic data support the theory of a greenhouse Earth during Cretaceous times (Sellwood & Valdes, 2006. Cretaceous paleoatmosphere. Taking in account the composition of the paleoatmosphere during the Cretaceous has considerably enriched the paleoclimatic debate. It is know that the CO2 concentrations of the Cretaceous atmosphere may have been 5 to 10 times higher than present day values (Berner & Kothavala, 2001). These high CO2 concentrations have often been used to explain higher rates of silicate mineral alteration. Nevertheless, although it is well understood that the CO2 content of the atmosphere controls the climate and therefore weathering, the specific mechanisms that intervene have rarely been studied. Here we will examine some aspects of the influence of CO2 upon weathering in order to reconsider the nature and the distribution of the Lower Cretaceous paleoweathering features. Simulation of granite weathering in high CO2 atmosphere. Two models, one of rainwater in equilibrium with the present day atmosphere and another with a CO2 atmospheric level 10 times higher than present day values (similar to the Lower Cretaceous atmosphere) have been developed and applied to a granite weathering simulation (Schmitt, 1999). The modelling shows that the successive minerals are the same for both simulations. But, under high atmospheric CO2 content, kaolinite appears with three times less rainwater flushed through the profile. This means that under similar rainfall and temperature conditions profiles would deepen three times faster than under present atmospheric conditions. Increased pCO2 has no direct effect on the appearance of gibbsite and hence on bauxite formation. Simulation of granite weathering at higher temperature (35 instead of 25°C) shows that gibbsite appears earlier, with about 20% less rainwater flushed through the profile, as a result of the increase in silica solubility between 25 and 35°C. The modelling also shows that elevated atmospheric CO2 values strongly accelerate the formation of deep kaolinitic profiles. This explains why deep kaolinized profiles, and kaolinite deposits have been widespread during the Cretaceous, even at extratropical latitudes, and under cool, moderately humide climate conditions. There is no direct effect of the simulated increased CO2 atmosphere on the rapidity of bauxitisation, but we know that the induced greenhouse effect and the particular Cretaceous paleogeography have both resulted in an increase in rainfall and in an important warming at intermediate latitudes. The simulation shows that the conjunction of these two factors is likely responsible for the expansion of the bauxites during the Cretaceous. Imprint in the sedimentary record The massive kaolinite formation during the Lower Cretaceous had a major impact on the clay mineral series of the sedimentary basins. The Upper Cretaceous sea level rise lead to the reworking of the kaolinitic weathering cover. Nevertheless the kaolinitic weathering paleoprofiles remained in place on wide continental areas until the Tertiary. A major reworking of these paleoprofiles occurred in Europe during the early Tertiary, when the climate became seasonally drier and vegetation cover more sparse, combined with the first Alpine tectonic movements. The kaolinite deposits of the Lower Eocene are mostly inherited from the Lower Cretaceous giant paleoweathering event. Berner R.A., Kothavala Z., 2001, GEOCARB III: a revised model of atmospheric CO2 over Phanerozoic time. American Journal of Science, 3001, p. 182-204. Bornemann, R.D. Norris, O. Friedrich, B. Beckmann, S. Schouten, J.S. Sinninghe Damsté, J. Vogel, P. Hofmann, T. Wagner. (2008). Isotopic evidence for glaciation during the cretaceous supergreenhouse. Science. 319 : 189-192. Schmitt J-M., 1999, Weathering, rainwater and atmosphere chemistry: example and modelling of granite weathering in present conditions, in a CO2-rich, and in an anoxic palaeoatmosphere. In : Palaeoweathering, palaeosurfaces and related continental deposits (eds. Thiry M. & Simon-Coinçon R.), Spec. Publ. Intern. Ass. Sediment., 27, p. 21 41. Thiry M., Quesnel F., Yans J., Wyns R., Vergari A., Théveniaut H., Simon-Coinçon R., Ricordel C., Moreau M.-G., Giot D., Dupuis C., Bruxelles L., Barbarand J., Baele J.-M, 2006, Continental France and Belgium during the Early Cretaceous : paleoweatherings and paleolandforms. Bull. Soc. géol Fr., 177/3 , p. 155 175. Sellwood B.W., Valdes P.J., 2006, Mesozoic climates: general circulation models and the rock record. Sedimentary Geology, 100, p. 269-287.

Geographic Size Variation and Intra-Tektite Geochemical Heterogeneity of Muong Nong Tektites: Insights for Cratering Process and Fall Location.

NASA Astrophysics Data System (ADS)

Schonwalder, D. A.; Sieh, K.; Herrin, J. S.; Wiwegwin, W.; Charusiri, P.; Singsomboun, K.; Sihavong, V.

2017-12-01

Australasian tektites cover 10% of Earth's surface and are the result of a 790 ka meteorite impact [1]. We have suggested that the search of the impact crater has long been mysterious because it lies buried beneath the volcanic field of the Bolaven Plateau (BP), southern Laos. [2]. Here we report our initial textural and geochemical work on 700 Muong Nong (MN) tektites collected in Laos and Thailand, including physical inspections and geochemical point-analyses of selected samples using a Field Emission Electron Probe Microanalyzer. We integrated our results with published data to identify any geographic patterns related to proposed crater site on the BP. Mung Nong tektite masses display a clear pattern in relation to BP. Within 50 km of the BP source, they do not exceed 10 gr. Mass then increases with radius to peak of 1 to 10 kg between 100 and 600 km, beyond which mass decreases steadily. We also see large geochemical heterogeneities within single tektites (e.g. 72.80±4.38 wt. % SiO2), and intra-sample compositions consisting with mixing of three principal source rocks on the BP, basalt-sourced laterites, basalt and sandstone. We infer that the geographical pattern in mass distribution of the MN tektites result from fragmentation of brittle, partially molten material during crater excavation and by debris interactions occurring in the ejecta blanket. The smaller and closest-to-crater tektites experienced greater interactions with crater walls and other ejecta during crater excavation, whereas the larger tektites that fell farther from the impact site, experienced lesser fragmentation because they had higher ejection trajectories that had less involvement in crater excavation. Intra-tektite compositional trends suggest the involvement of three protoliths, all of them found at the BP. 1. Schwarz et al. (2016) Geochem. Cosmo. Acta 178 2. Sieh et al. (2015) AGU Fall Mtg. T54A-04

The pH-dependent leaching behavior of slags from various stages of a copper smelting process: Environmental implications.

PubMed

Jarošíková, Alice; Ettler, Vojtěch; Mihaljevič, Martin; Kříbek, Bohdan; Mapani, Ben

2017-02-01

The leaching behaviors of primary copper (Cu) slags originating from Ausmelt, reverbatory, and converter furnaces operating under a single technological process were compared to a residual slag tailing obtained by slag re-processing via flotation and metal recovery. The EN 12457-2 leaching test, used for assessment of the hazardous properties, was followed by the CEN/TS 14997 pH-static leaching test (pH range 3-12). Both leaching experiments were coupled with a mineralogical investigation of the primary and secondary phases as well as geochemical modeling. Metals (Cd, Cu, Pb, Zn) exhibit the highest leaching at low pH. Under acidic conditions (pH 3-6), Ausmelt slag and slag tailing exhibited higher metal leaching compared to other slag types. Very low leaching of metals (far below EU limits for non-hazardous waste) was observed at natural pH (7.9-9.0) for all the studied slag samples. In contrast, relatively high leaching of As was observed over the entire pH range, especially for Ausmelt slag (exceeding the EU limit for hazardous waste by 1.7×). However, geochemical modeling and scanning electron microscopy indicated that formation of stable Ca-Cu-Pb arsenates and the binding of As to newly formed Fe (oxyhydr)oxides play an important role in efficient As immobilization at the slag-water interface. In contrast, no controls were predicted for Sb, whose leaching was almost pH-independent. Nevertheless Sb leached concentrations at natural pH were below EU limit for hazardous waste. Re-processing of primary Cu slags for metal recovery, and subsequent co-disposal of the resulting slag tailing with dolomite-rich mine tailing and local laterite is suitable for stabilizing the remaining contaminants (except Sb) and limiting their leaching into the environment. Copyright © 2016 Elsevier Ltd. All rights reserved.

Chemical analysis of black crust on the Angkor sandstone at the Bayon temple, Cambodia

NASA Astrophysics Data System (ADS)

Song, Wonsuh; Oguchi, Chiaki; Waragai, Tetsuya

2014-05-01

The Angkor complex is the one of the greatest cultural heritages in the world. It is constructed in the early 12th century, designated as a world cultural heritage by UNESCO in 1992. The temples at the Angkor complex are mainly made of sandstone and laterite. However, due to the tropical climate, plants, lichens and various microorganisms are growing well on the rock surface. Black crusts are also easily found on the stone surface. The 21st technical session of the International Coordinating Committee for the Safeguarding and Development of the Historic Site of Angkor (ICC-Angkor) held in 2012 recommended that to preserve both the biofilms and the forest cover and to prohibit the biocides (chlorine-based) and organic biocides. However, there are many reports that lichens and microorganisms accelerate rock weathering. It is important to clarify that how the biofilm on the Angkor temples affect Angkor sandstones. We sampled Angkor sandstone covered by black crust at the Bayon temple, Angkor complex, and observed the section and the surface of the rock sample by using SEM. Surfaces of the samples are not polished in order to observe the original condition. The samples are coated with gold for 180 seconds. The depth of the black crust is up to 1 mm. Many filamentous materials were found on the black crust. Average energy-dispersive X-ray spectroscopy data of the five areas of ca. 20 μm ×15 μm in the black crusts shows that over 80 % of the filamentous materials are compounds of carbon. It seems that these materials are hyphae. The shape of the hypha is like a thread and its size is few μm in diameter and up to several centimeters in length. Black crusts are consisted of elements and compounds of carbon, Na, Mg, Al, Si, Cl, K, Ca, and Fe. Further research has to be done to find out the better and proper way of conservation for the Angkor complex.

Geomicrobiological Features of Ferruginous Sediments from Lake Towuti, Indonesia

PubMed Central

Vuillemin, Aurèle; Friese, André; Alawi, Mashal; Henny, Cynthia; Nomosatryo, Sulung; Wagner, Dirk; Crowe, Sean A.; Kallmeyer, Jens

2016-01-01

Lake Towuti is a tectonic basin, surrounded by ultramafic rocks. Lateritic soils form through weathering and deliver abundant iron (oxy)hydroxides but very little sulfate to the lake and its sediment. To characterize the sediment biogeochemistry, we collected cores at three sites with increasing water depth and decreasing bottom water oxygen concentrations. Microbial cell densities were highest at the shallow site—a feature we attribute to the availability of labile organic matter (OM) and the higher abundance of electron acceptors due to oxic bottom water conditions. At the two other sites, OM degradation and reduction processes below the oxycline led to partial electron acceptor depletion. Genetic information preserved in the sediment as extracellular DNA (eDNA) provided information on aerobic and anaerobic heterotrophs related to Nitrospirae, Chloroflexi, and Thermoplasmatales. These taxa apparently played a significant role in the degradation of sinking OM. However, eDNA concentrations rapidly decreased with core depth. Despite very low sulfate concentrations, sulfate-reducing bacteria were present and viable in sediments at all three sites, as confirmed by measurement of potential sulfate reduction rates. Microbial community fingerprinting supported the presence of taxa related to Deltaproteobacteria and Firmicutes with demonstrated capacity for iron and sulfate reduction. Concomitantly, sequences of Ruminococcaceae, Clostridiales, and Methanomicrobiales indicated potential for fermentative hydrogen and methane production. Such first insights into ferruginous sediments showed that microbial populations perform successive metabolisms related to sulfur, iron, and methane. In theory, iron reduction could reoxidize reduced sulfur compounds and desorb OM from iron minerals to allow remineralization to methane. Overall, we found that biogeochemical processes in the sediments can be linked to redox differences in the bottom waters of the three sites, like oxidant concentrations and the supply of labile OM. At the scale of the lacustrine record, our geomicrobiological study should provide a means to link the extant subsurface biosphere to past environments. PMID:27446046

Persistence of Pathogenic and Non-Pathogenic Escherichia coli Strains in Various Tropical Agricultural Soils of India

PubMed Central

Naganandhini, S.; Kennedy, Z. John; Uyttendaele, M.; Balachandar, D.

2015-01-01

The persistence of Shiga-like toxin producing E. coli (STEC) strains in the agricultural soil creates serious threat to human health through fresh vegetables growing on them. However, the survival of STEC strains in Indian tropical soils is not yet understood thoroughly. Additionally how the survival of STEC strain in soil diverges with non-pathogenic and genetically modified E. coli strains is also not yet assessed. Hence in the present study, the survival pattern of STEC strain (O157-TNAU) was compared with non-pathogenic (MTCC433) and genetically modified (DH5α) strains on different tropical agricultural soils and on a vegetable growing medium, cocopeat under controlled condition. The survival pattern clearly discriminated DH5α from MTCC433 and O157-TNAU, which had shorter life (40 days) than those compared (60 days). Similarly, among the soils assessed, the red laterite and tropical latosol supported longer survival of O157-TNAU and MTCC433 as compared to wetland and black cotton soils. In cocopeat, O157 recorded significantly longer survival than other two strains. The survival data were successfully analyzed using Double-Weibull model and the modeling parameters were correlated with soil physico-chemical and biological properties using principal component analysis (PCA). The PCA of all the three strains revealed that pH, microbial biomass carbon, dehydrogenase activity and available N and P contents of the soil decided the survival of E. coli strains in those soils and cocopeat. The present research work suggests that the survival of O157 differs in tropical Indian soils due to varied physico-chemical and biological properties and the survival is much shorter than those reported in temperate soils. As the survival pattern of non-pathogenic strain, MTCC433 is similar to O157-TNAU in tropical soils, the former can be used as safe model organism for open field studies. PMID:26101887

Cenozoic Uplift, Erosion and Dynamic Support of Madagascar

NASA Astrophysics Data System (ADS)

Stephenson, Simon; White, Nicky

2016-04-01

The physiography of Madagascar is characterised by high-elevation but low-relief topography; 42% of the landscape is above 500 m in elevation. Eocene (marine) nummulitic (marine) limestones at elevations of ˜400 m above sea level and newly dated, emergent 125 ka coral reefs suggest that Madagascar has experienced differential vertical motions during Cenozoic times. Malagasy rivers are often deeply incised and contain steepened reaches, implying that they have responded to changes in regional uplift rate. However, low temperature thermochronology and 10Be derived erosion rates suggest that both Cenozoic and Recent average denudation rates have been low. Extensive laterite-capped, low-relief surfaces also suggest that there have been long periods of tectonic quiescence. In contrast, the modern landscape is characterised by erosional gullies (i.e. lavaka), with very high local erosion rates. To bridge the gap between this disparate evidence, we inverted 2566 longitudinal river profiles using a damped non-negative, least-squares linear inversion to determine the history of regional uplift. We used a simplified version of the stream power erosional law. River profiles were extracted from the 3 arc-second Shuttle Radar Topography Mission (SRTM) digital elevation model. Calibration of the stream power erosional law is based upon Cenozoic limestones and new radiometrically dated marine terraces. The residual misfit between observed and calculated river profiles is small. Results suggest that Malagasy topography grew diachronously by 1-2 km over the last 15-20 Ma. Calculated uplift and denudation are consistent with independent observations. Thus drainage networks contain coherent signals that record regional uplift. The resultant waves of incision are the principal trigger for modern erosional processes. Admittance calculations, the history of basaltic volcanism and nearby oceanic residual age-depth measurements all suggest that as much as 0.8 - 1.1 km of Cenozoic uplift in Madagascar is supported by mantle processes.

Effect of soil pH and organic matter on the adsorption and desorption of pentachlorophenol.

PubMed

Chien, Shui-Wen Chang; Chen, Shou-Hung; Li, Chi-Jui

2018-02-01

Various properties of soil affect the partition of organic contaminants within, and conversely, the properties of the organic contaminants also directly affect their partition behavior in soil. Therefore, understanding the effects of various properties of soil on the partition of organic contaminants favors subsequent assessment and provides soil remediation methods for policymakers. This study selected pentachlorophenol (PCP), a common hydrophobic ionizable organic compound in contaminated sites worldwide, as the target contaminant. The effects of pH, organic matter, and the combination of both, on PCP adsorption/desorption behavior in soil were investigated. Phosphoric acid and potassium hydroxide were used as buffer solutions to modify the soil pH by the batch and column extraction methods. A common retail organic fertilizer and fulvic acid were selected as additives to manipulate the soil organic content. Modifying the pH of the soil samples revealed that acidic soil exhibited a greater PCP adsorption rate than alkaline soil. The amount of PCP desorption increased regardless of pH of the in situ contaminated soil. The adsorption of PCP increased with increasing amount of organic additive. However, addition of fulvic acid yielded different results compared to the addition of organic fertilizer. Specifically, the organic fertilizer could not compete with the in situ contaminated soil in PCP adsorption, whereas fulvic acids increased the PCP dissolution to facilitate adsorbing contaminant adsorption. The combined effect of pH modification and organic matter addition provides additional PCP adsorption sites; therefore, adding the organic fertilizer to decrease the soil pH elevated the PCP adsorption rates of the laterite, alluvial, and in situ contaminated soil samples. The study results revealed that both pH and organic matter content are crucial to PCP adsorption/desorption in soil. Therefore, the effects of soil pH and organic matter should be considered in facilitating PCP treatment for soil remediation.

Quaternary stratigraphy of Bermuda: A high-resolution pre-Sangamonian rock record

NASA Astrophysics Data System (ADS)

Hearty, Paul J.; Vacher, H. Leonard

Carbonate islands such as Bermuda are created by climatic change. Warm climates and high sea levels stimulate carbonate sediment production that may ultimately result in island growth, while cold glacials expose the platforms to weathering, dissolution and soil formation. Of great importance in Quaternary studies is the ability to decipher this climatic history. Mapping and geochronologic studies have established that Bermuda may have one of the most continuous and detailed Quaternary interglacial depositional records on a carbonate platform. Advances in racemization dating (AAR) have offered a means of deciphering this climatic history and generating a high-resolution stratigraphic and age framework for the Quaternary. Bermudian interglacial units consist predominantly of eolianites, with less voluminous occurrences of beach deposits and calcarenite protosols (Entisols). Glacial or stadial-age terra rossa (aluminous laterite) paleosols, whose degree of development is a function of time of exposure, form boundaries between interglacial units. D-alloiso-leucine/ L-isoleucine ( {A}/{I}) ratios have been determined on marine pelecypods, land snails and whole-rock samples from mapped sections; aminozones have been defined for two Sangamonian and at least five pre-Sangamonian depositional intervals. From kinetic models based on calibration with previously published U-series coral dates, estimated ages of middle Pleistocene and older aminozones are: F = 190,000-265,000 years; G = 300,000-400,000 years; H = 400,000-500,000 years; J = >700,000 years; and K = > 900,000 years. Aminozone G, which is correlated with the upper Town Hill Formation and Isotope Stage 9, is volumetrically the most important depositional event of the middle Pleistocene. The great mass of sediment deposited during this period suggests an interglacial of significant duration and prolonged shelf submergence, during which the island grew to over half its present size. Only the Sangamonian ( sensu lato) rivals Stage 9 in volume of eolianite deposited on the island. Sea-level amplitude, as determined from dated outcrops, appears to correlate well with amplitudinal variations in the oxygen isotope record.

Risk assessment of drought disaster in southern China

NASA Astrophysics Data System (ADS)

Wang, Y.

2015-12-01

Abstract: Drought has become an increasing concern in southern China, but the drought risk has not been adequately studied. This study presents a method for the spatial assessment of drought risk in southern China using a conceptual framework that emphasizes the combined role of hazard, vulnerability, and exposure.A drought hazard map was retrieved with a compound index of meteorological drought method in a GIS environment. Normally, a large variation in the disaster-inducing factor implies a high probability of economic/social losses caused by a drought disaster. The map indicated that areas with a higher risk of drought hazard were mainly distributed in mid-east Yunnan and the basins in eastern Sichuan.The vulnerability indices were based on climate factors as well as land use, geomorphological types, soil properties, and drainage density. The water preserving capability of purple calcareous soil in the basins in Sichuan and mid-east Yunnan, and the lateritic red soil in northeastern Guangdong is relatively weak. The main geomorphological features in Guangxi and Guangdong are hills, which leads to a serious expectation of soil and water losses. Thus, the main areas with a high risk of drought vulnerability are mid-east Yunnan and the basins in eastern Sichuan.The exposure indices were based on population density and agricultural production because population and agriculture experience the main impacts of a drought disaster. Higher exposure indices mean higher economic/social losses due to drought disasters. Areas with high exposure indices were mainly distributed in Guangdong and southern Guangxi.The overall risk was then calculated as the product of the hazard, vulnerability, and exposure. The results indicated a higher risk of drought disaster in the basins in eastern Sichuan,, northeastern Yunnan, and northeastern Guangdong. The main factor influencing the risk of a drought disaster was the hazard, but the vulnerability and exposure also played important roles.

Trace metal geochemistry in mangrove sediments and their transfer to mangrove plants (New Caledonia).

PubMed

Marchand, C; Fernandez, J-M; Moreton, B

2016-08-15

Because of their physico-chemical inherent properties, mangrove sediments may act as a sink for pollutants coming from catchments. The main objective of this study was to assess the distribution of some trace metals in the tissues of various mangrove plants developing downstream highly weathered ferralsols, taking into account metals partitioning in the sediment. In New Caledonia, mangroves act as a buffer between open-cast mines and the world's largest lagoon. As a result of the erosion of lateritic soils, Ni and Fe concentrations in the sediment were substantially higher than the world average. Whatever the mangrove stand and despite low bioaccumulation and translocations factors, Fe and Ni were also the most abundant metals in the different plant tissues. This low bioaccumulation may be explained by: i) the low availability of metals, which were mainly present in the form of oxides or sulfur minerals, and ii) the root systems acting as barriers towards the transfer of metals to the plant. Conversely, Cu and Zn metals had a greater mobility in the plant, and were characterized by high bioconcentration and translocation factors compared to the other metals. Cu and Zn were also more mobile in the sediment as a result of their association with organic matter. Whatever the metal, a strong decrease of trace metal stock was observed from the landside to the seaside of the mangrove, probably as a result of the increased reactivity of the sediment due to OM enrichment. This reactivity lead to higher dissolution of bearing phases, and thus to the export of dissolved trace metals trough the tidal action. Cu and Zn were the less concerned by the phenomenon probably as a result of higher plant uptake and their restitution to the sediment with litter fall in stands where tidal flushing is limited. Copyright © 2016 Elsevier B.V. All rights reserved.

Should there be a "Wet" Soil Order in Soil Taxonomy?

NASA Astrophysics Data System (ADS)

Rabenhorst, Martin; Wessel, Barret; Stolt, Mark; Lindbo, David

2017-04-01

Early soil classification systems recognized wet soils at the highest categorical level. Among the Intrazonal Soils of the US classification utilized between the 1920s and 1960, were included as Great Soil Groups, the Wiesenboden, Bog, Half-Bog, Ground-Water Podzols and Ground-Water Laterites. In other systems, groups named with such terms as ground water gley and pseudogley were also used. With the advent of Soil Taxonomy and it's precursor (1960, 1975), Histosols (organic soils) were distinguished as one of the initial 10 soil orders, and while many of these organic soils are wet soils, some are not (Folists for example). Thus, for over 50 years, with the exception of Histosols, wet soils (which typically represent the wettest end of subaerial wet soils) have not been collectively recognized within taxa at the highest categorical level (order) in the US soil classification system. Rather, the wettest soils were designated at the second categorical level as wet (Aqu) suborders among the various soil orders, and more recently, subaqueous soils as "Wass" suborders of Entisols and Histosols. Soils with less-wet conditions have been recognized at the subgroup (4th) level. Further, in impoundments and regions of transgressing coastlines, submerged upland soils have been found that still classify in soil orders that do not accommodate subaqueous soils ("Wass" suborders). Notwithstanding, other contemporary soil classification systems do (have continued to) recognize wet soils at the highest level. In the World Reference Base (WRB) for example, wet soils are designated as Gleysols or Stagnosols. As efforts are underway to revisit, simplify, and revise Soil Taxonomy, questions have been raised regarding whether wet soils should again be moved back with a place among taxa at the highest category using a name such as Hydrasols, Aquasols, etc. This paper will explore and consider the questions and arguments for and against such proposals and the difficult question regarding where along the soil wetness continuum would be the best point for recognizing a wet soil order.

Fine-grained Goethite as a Precursor for Martian Gray Hematite

NASA Technical Reports Server (NTRS)

Glotch, T. D.; Morris, R. V.; Sharp, T. G.; Christensen, P. R.

2003-01-01

Several isolated deposits of gray, crystalline hematite on Mars were discovered using data returned from the Thermal Emission Spectrometer (TES) instrument aboard the Mars Global Surveyor spacecraft. Christensen et al. provided five testable hypotheses regarding the formation of crystalline hematite on Mars: 1) low-temperature precipitation of Fe oxides/hydroxides from standing, oxygenated, Fe-rich water, followed by subsequent alteration to gray hematite, 2) low-temperature leaching of iron-bearing silicates and other materials leaving a Fe-rich residue laterite-style weathering) which is subsequently altered to gray hematite, 3) direct precipitation of gray hematite from Fe-rich circulating fluids of hydrothermal or other origin, 4) formation of gray hematitic surface coatings during weathering, and 5) thermal oxidation of magnetite-rich lavas. Since this initial work, several authors have examined the hematite deposits to determine their formation mechanism. Lane et al. cited the absence of a 390/ cm absorption in the martian hematite spectrum as evidence for platy hematite grains. Their model for the formation of the deposits includes deposition of any of a variety of iron oxides or oxyhydroxides by aqueous or hydrothermal fluids, burial and metamorphosis to gray platy hematite grains, and exhumation in recent times. Based on a detailed geomorphic examination of the Sinus Meridiani region, Hynek et al. conclude that the most likely method of hematite formation was either emplacement by a hydrothermal fluid or oxidation of a magnetite-rich pyroclastic deposit. Similarly, Arvidson et al., favor a model involving the alteration of pyroclastic deposits by aqueous or hydrothermal fluids. Finally, based on geochemical modeling and an examination of Aram Chaos, Catling and Moore favor emplacement by hydrothermal fluids with a minimum temperature of 100 C. Comparison of the average martian hematite spectrum measured by TES to hematite emissivity spectra for a variety of naturally occurring hematites shows small but potentially important differences. In particular, band shapes, positions and relative band emissivities of hematite spectra vary over the range of samples. These differences imply that the natural variability of thermal infrared hematite spectra has not been fully characterized, especially with respect to the reaction pathway and crystal structure.

Environmental Changes Associated With Deccan Volcanism: evidences from the red bole record

NASA Astrophysics Data System (ADS)

Nikhil, Sharma; Valentin, Sordet; Thierry, Adatte; Gerta, Keller; Eric, Font; Blair, Schoene; Kyle, Samperton; Syed, Khadri

2017-04-01

Recent studies indicate that the bulk (80%) of Deccan trap eruptions occurred over a relatively short time interval in magnetic polarity C29r. U-Pb zircon geochronology shows that the main phase-2 began 250 ky before the Cretaceous-Tertiary (KT) mass extinction and continued into the early Danian suggesting a cause-and-effect relationship. Closer to the eruption center, the lava flows are generally separated by red weathered horizons known as red boles that mark quiescent periods between basalt flows. A typical red bole begins with the fresh underlying basalt and evolves into weathered basalt, then, a layer of basalt in a rounded shape called 'bole' surrounded by clays at the top, which is overlain by the next lava flow. Red boles have increasingly attracted the attention of researchers to understand the climatic and paleoenvironmental impact of Continental Flood Basalts (CFB). Recent advances in U-Pb dating of Deccan lava flows, studies of weathering patterns and paleoclimatic information gained from multiproxy analyses of red bole beds (e.g., lithology, mineralogy, geochemistry) yield crucial evidence of environmental changes triggered by volcanic activity. Red boles consist mainly of red silty clays characterized by concentrations of immobile elements such as Al and Fe3+ ions that are typical of paleo-laterites, which probably developed during the short periods of weathering between eruptions. Clay minerals consist mostly of smectite suggesting semi-arid monsoonal conditions. At least 30 thick red bole layers are present in C29r below the KT boundary between lava flows of phase-2 that erupted over a time span of about 250 ky. The short duration exposures of these red boles are reflected in the mineralogical and geochemical data that indicate rapid weathering (high CIA) linked to increasing acid rains. ∂D and ∂18O measured on smectite clays from the red boles approximate the meteoric water composition that prevailed during Deccan eruptions. Isotopic data from red boles deposited through the main phase-2 suggest significant and rapid changes in rainfall intensity and/or altitude linked to the accumulation of a 3100m thick basalt pile that erupted over a short period of time.

Cobalt—Styles of deposits and the search for primary deposits

USGS Publications Warehouse

Hitzman, Murray W.; Bookstrom, Arthur A.; Slack, John F.; Zientek, Michael L.

2017-11-30

Cobalt (Co) is a potentially critical mineral. The vast majority of cobalt is a byproduct of copper and (or) nickel production. Cobalt is increasingly used in magnets and rechargeable batteries. More than 50 percent of primary cobalt production is from the Central African Copperbelt. The Central African Copperbelt is the only sedimentary rock-hosted stratiform copper district that contains significant cobalt. Its presence may indicate significant mafic-ultramafic rocks in the local basement. The balance of primary cobalt production is from magmatic nickel-copper and nickel laterite deposits. Cobalt is present in several carbonate-hosted lead-zinc and copper districts. It is also variably present in Besshi-type volcanogenic massive sulfide and siliciclastic sedimentary rock-hosted deposits in back arc and rift environments associated with mafic-ultramafic rocks. Metasedimentary cobalt-copper-gold deposits (such as Blackbird, Idaho), iron oxide-copper-gold deposits, and the five-element vein deposits (such as Cobalt, Ontario) contain different amounts of cobalt. None of these deposit types show direct links to mafic-ultramafic rocks; the deposits may result from crustal-scale hydrothermal systems capable of leaching and transporting cobalt from great depths. Hydrothermal deposits associated with ultramafic rocks, typified by the Bou Azzer district of Morocco, represent another type of primary cobalt deposit.In the United States, exploration for cobalt deposits may focus on magmatic nickel-copper deposits in the Archean and Proterozoic rocks of the Midwest and the east coast (Pennsylvania) and younger mafic rocks in southeastern and southern Alaska; also, possibly basement rocks in southeastern Missouri. Other potential exploration targets include—The Belt-Purcell basin of British Columbia (Canada), Idaho, Montana, and Washington for different styles of sedimentary rock-hosted cobalt deposits;Besshi-type VMS deposits, such as the Greens Creek (Alaska) deposit and the Ducktown (Tennessee) waste and tailings; andKnown five-element vein districts in Arizona and New Mexico, as well as in the Yukon-Tanana terrane of Alaska; and hydrothermal deposits associated with ultramafic rocks along the west coast, in Alaska, and in the Appalachian Mountains.

Large Igneous Provinces, Their Giant Mafic Dyke Swarms, and Links to Metallogeny

NASA Astrophysics Data System (ADS)

Jowitt, S.; Ernst, R. E.

2017-12-01

The relationships between large igneous provinces (LIPs), their giant dyke swarms and differing metallogenic systems can be condensed into five distinct although partially overlapping classifications: (1) LIP magmas that directly generate mineral deposits such as orthomagmatic Ni-Cu-PGE sulfides. Many carbonatites (Nb, Ta REE deposits) and kimberlites (diamonds) are also often LIP related. On the other hand, LIP-related thermal pulses (from a mantle plume) can sometimes destroy diamond potential in the overlying lithosphere. A key locus for Ni-Cu-PGE mineralization is within a few hundred km of the plume center region and plume centers are best located using giant radiating dyke swarms. Dyke subswarms with chalcophile element depletions can also be tracked "upstream" toward the plume center to identify exploration targets. (2) LIP magmas that provide energy, fluids, and/or metals for ore types such as hydrothermal volcanogenic massive sulfide (VMS) and iron oxide-copper-gold (IOCG) deposits. Heat loss from the margins of dykes and sills can also generate local enrichments in key metals (e.g. Co) within the surrounding sedimentary rocks. (3) LIP rocks (particularly sills and dykes) can act barriers to fluid flow and/or as reaction zones that control mineralizing events, act as structural traps within hydrocarbon systems, and form impermeable barriers that control water flow and hence aquifer formation (4) surficial effects, such as the formation of Ni-Co laterites and Al bauxites from tropical weathering of LIP mafic-ultramafic rocks (including volcanics fed by radiating dykes as well as the dykes themselves). This category also includes LIP-related anoxia events that generate hydrocarbon source rocks; and (5) indirect links between LIPs and ore deposits, where continental breakup-related LIP events define a `barcode' record (usually dominated by dyke swarms) that can be used to correlate and reconstruct Precambrian supercontinents. This fifth classification type also includes links between major continental breakup (linked to LIPs and their dyke swarms) and distal compression and transpression in the plate tectonic circuit, leading to the formation of orogeny-related deposits such as orogenic Au mineralization.

Reconnaissance geology of the Central Mastuj Valley, Chitral State, Pakistan

USGS Publications Warehouse

Stauffer, Karl W.

1975-01-01

The Mastuj Valley in Chitral State is a part of the Hindu Kush Range, and is one of the structurally most complicated areas in northern Pakistan. Sedimentary rocks ranging from at least Middle Devonian to Cretaceous, and perhaps Early Tertiary age lie between ridge-forming granodiorite intrusions and are cut by thrust faults. The thrust planes dip 10? to 40? to the north- west. Movement of the upper thrust plates has been toward the southeast relative to the lower blocks. If this area is structurally typical of the Hindu-Kush and Karakoram Ranges, then these mountains are much more tectonically disturbed than previously recorded, and suggest compression on a scale compatible with the hypothesis that the Himalayan, Karakoram, and Hindu Kush Ranges form part of a continental collision zone. The thrust faults outline two plates consisting of distinctive sedimentary rocks. The lower thrust plate is about 3,000 feet thick and consists of the isoclinally folded Upper Cretaceous to perhaps lower Tertiary Reshun Formation. It has overridden the Paleozoic metasedimentary rocks of the Chitral Slate unit. This thrust plate is, in turn, overridden by an 8,000-foot thick sequence consisting largely of Devonian to Carboniferous limestones and quartzites. A key factor in the tectonic processes has been the relatively soft and plastic lithology of the siltstone layers in the Reshun Formation which have acted as lubricants along the principal thrust faults, where they are commonly found today as fault slices and smears. The stratigraphic sequence, in the central Mastuj Valley was tentatively divided into 9 mapped units. The fossiliferous shales and carbonates of the recently defined Shogram Formation and the clastlcs of the Reshun Formation have been fitted into a sequence of sedimentary rocks that has a total thick- ness of at least 13,000 feet and ranges in age from Devonian to Neogene. Minerals of potential economic significance include antimony sulfides which have been mined elsewhere in Chitral, the tungstate, scheelite, which occurs in relatively high concentrations in heavy-mineral fractions of stream sands, and an iron-rich lateritic rock.

Review of cenozoic ooidal ironstones

NASA Astrophysics Data System (ADS)

van Houten, Franklyn B.

1992-06-01

Cenozoic (Tertiary) ooidal ironstones (COI) in 20 districts (39 deposits) developed between the equatorial zone and 60° N, except for one Eocene district in mid-southern latitude. Stratigraphic distribution. Paleocene OI occur in northern Pakistan, western Siberia, southern Germany, northwestern Venezuela, and northeastern Colombia: Eocene OI in western Siberia, southern Germany, northwestern Romania, central North Africa, central-west Saudi Arabia, southwestern Central Africa, northwestern Venezuela, northeastern Colombia, south-central USA, and northwestern Australia; Oligocene OI in northwest and west-central Kazakhstan, central Denmark, and north-central Iran?; Miocene OI in northwestern Venezuela, northeastern Colombia, and southeastern Malaysia; Pliocene OI in southeastern Ukraine. Geotectonic framework. Ten districts developed in an interior or fractured craton: five along the south-trending Uralian Seaway, and one along the east-trending Northern European Seaway, the south-trending Trans-Saharan Seaway, in or near an early Red Sea embayment, in southeastern Malaysia, and in northwestern Australia. Ten districts lay near a eratonic margin: one along divergent margin and nine along the broad east-trending Caribbean and Tethyan seaways. Almost all COI accumulated during the Paleogene relatively high stand of sea level, especially in Early and Middle Eocene time. As sea level fell gradually in Neogene time COI developed in only three marginal districts (including the giant Pliocene Kerch-Taman deposit in southeastern Ukraine). Sedimentary environment. Almost all of the COI developed in deltaic to shallow marine facies. These are commonly associated with shoaling-upward siliciclastic sequences; a few are in mixed siliciclastic-carbonate sequences. A few COI apparently occurred in fluvial and lacustrine facies; some of these may have been reworked from laterite or from marine ironstones. Sedimentary petrology. Many COI are less than a few tens of centimeters thick and sporadic. The ooids are entirely or predominantly ferric oxide. A few contain a minor amount of berthierine (7A); only the oldest one (northern Pakistan) contains chamosite (14A). More than half of the COI are associated directly or more remotely with glauconite. Nearly all the COI need much more rigorous examination for both their individual composition and their comparison with older ooidal ironstones.

Sea level reconstructions and non-marine sedimentation at the Triassic-Jurassic boundary: southwestern margin of the Neotethys in the Salt Range, Pakistan

NASA Astrophysics Data System (ADS)

Iqbal, Shahid; Wagreich, Michael

2016-04-01

The environmental changes during the Triassic-Jurassic boundary interval and the associated mass extinction event are still strongly debated. Sea-level reconstruction records during this interval reveal an end-Triassic global regression event. Erosion and karstification at the top of Triassic sediments, and Lower Jurassic fluvial channels with reworked Triassic clasts indicate widespread regression in the European basins. Laterite at the top of the Triassic, and quartzose conglomerates/sandstones at the base of the Jurassic indicate a fluvial/terrestrial onset in Iran and Afghanistan. Abrupt emergence, erosion and facies dislocation, from the Triassic dolomites (Kingriali Formation) to Lower Jurassic fluvial/continental quartzose conglomerates/pebbly sandstones (Datta Formation) occur in the Tethyan Salt Range of Pakistan. Sedimentological analyses indicate marine regression and emergence under tropical-subtropical conditions (Greenhouse conditions) and negates the possibility of glacial influence in this region. Field evidences indicate the presence of an undulatory surface at the base of the Jurassic and a high (Sargodha High) is present south of the Salt Range Thrust, the southern boundary of the basin. Furthermore, geophysical data (mostly seismic sections) in different parts of the basin display normal faults in the basement. These features are interpreted as horst and graben structures at the Triassic-Jurassic boundary in the Kohat-Potwar Plateau. The Lower Jurassic Datta Formation appears to have been deposited in an overall graben fill settings. Similar normal faults and graben fill geometries are observed on seismic sections in Tanzania, Mozambique, Madagascar and other regions of the southeastern margin of the African Plate and are related to the Karoo rift system. To summarize, the basement normal faults and the graben fill features at the Triassic-Jurassic boundary in the Kohat-Potwar Plateau can be correlated to similar features common in the Karoo rift area. Regional sea-level fall associated with this rift produced erosional and reworking features similar to those occur at the Triassic-Jurassic boundary in the European basins, Iran and Afghanistan. The tectonic correlation with the European basins and sedimentological evidences for the globally present Jurassic-Triassic boundary in the Salt Range of Pakistan encourage a detail work in this regard.

When did a Mediterranean-type climate originate in southwestern Australia?

NASA Astrophysics Data System (ADS)

Lamont, Byron B.; He, Tianhua

2017-09-01

Knowing the environments under which biota have evolved is essential for understanding the functional traits that they possess. Here, we ask when a Mediterranean-type climate (MTC) originated in Western Australia that might help to explain some of its special plant adaptations to summer drought and heat, mild wet winters and intense summer fires. Periodic drought and fire can be traced back to the Cretaceous in southwestern Australia (SWA) but its seasonality is unknown. Previous estimates of the origin of the MTC in SWA have varied from 30 to 3 million years ago (Ma). An early proposal was that it originated in northwestern Australia 30 Ma and migrated south to its present location for which we find independent support. We collated 47 cases of what is currently known about the time of origin of adaptive responses to summer drought and heat, wet winters and periodic intense fire among flowering plants in SWA. About 15% arose in the 40-30-million-year (My) period, 32% in the 30-20-My period and 47% in the 20-10-My period, suggesting that a MTC may have been widespread in SWA by the mid-Miocene, but there may have been local appearances (proto-MTC) up to 20 My earlier. Uncertainties remain about the location of lineages at various times, the fitness benefits of apparent adaptive traits and their confinement to a MTC, and the significance of the origin versus the onset of diversification of traits. The current dearth of C4 grasses in SWA is consistent with other indications of the absence of a prior history of a summer-dominant rainfall, suggesting that the current MTC arose from a uniform-rainfall climate. Other lines of evidence that might refine these findings include the chemical composition of, and application of geochronometers to, laterites, carbonates and corals that have been used with success elsewhere. We conclude by noting that there may have been a mixture of climates for much of the time, indicated by the persistence of a few rainforest species up to 3 Ma, while there have been strong climatic oscillations about a MTC 'mean' over the last 5 My.

Grow your own REE deposits: Novel observations from the soils of Southern Portugal

NASA Astrophysics Data System (ADS)

Hardy, Liam; Smith, Martin; Boyce, Adrian; McDonald, Alison; Heller, Shaun; Bamberger, Axel; Blum, Astrid; Hood, Leo

2017-04-01

Industrialised eucalyptus farming in Serra de Monchique has been well documented for its regional impacts on water flow, for its destructive centralisation of local economics (Jenkins, 1979) and for its derogatory impacts on local ecology (Brito, 1999) (Matias & Lamberts, 2011), it is another story of cash cropping for short term gain in an area of sensitive environmental balance which had previously been suitably subsistence farmed for some 700 years with no outside influence until the early 1950s (Jenkins, 1979). The farming has irreversibly changed local customs, soil and water systems, but formed new and intricate relationships between the troposol, oxisol and latosol formations and plants which have not previously been studied in this region in terms of soil geochemistry. During research in the region (as part of the SoS Rare/NERC-UK program) into metal and clay interactions in the troposol formations of Monchique, it was noted that rare earth elements (REEs) and other soluble ions were being mobilised in the upper half of the profiles by some seasonal cycle other than the natural meteoric input/leaching expected during classical lateritisation (Tardy, 1997). It was observed that some 40% of Fe and some 30% of Y were leaving the profile during wet season and concentrating at specific depths during dry seasons to a grade of some 160ppm Y and were thus, potentially viable as an economic resource of Heavy REEs. This PICO presentation discusses the proposed anthropogenic/biogenic mechanism for this concentration and how you too could potentially grow an economically viable REE enriched garden. References: Brito, J. G. (1999). Management strategies for conservation of the lizard Lacerta schreiberi in Portugal. Biological conservation, 311-319. Jenkins, R. (1979). The Road to Alto: An account of peasants, capitalists and their soil in the mountains of Southern Portugal. London: Pluto, ISBN: 0861040767. Matias, M., & Lamberts, P. (2011, May 26). Parliamentary questions. Retrieved from European Parliamentary Records Nash, D., & Mclaren, S. (2007). Geochemical Sediments and Landscapes. London: Wiley-Blackwell. Tardy, Y. (1997). Petrology of Laterites & Tropical Soils. Rotterdam: A. A. Balkema.

Geomorphological and Geoelectric Techniques for Kwoi's Multiple Tremor Assessment

NASA Astrophysics Data System (ADS)

Dikedi, P. N.

2017-12-01

This work epicentres on geomorphological and geoelectric techniques for multiple tremor assessment in Kwoi, Nigeria. Earth tremor occurrences have been noted by Akpan and Yakubu (2010) within the last 70 years, in nine regions in Nigeria; on September 11,12,20,22, 23 and 24, 2016, additional earth tremors rocked the village of Kwoi eleven times. Houses cracked and collapsed, a rock split and slid and smoke evolved at N9027''5.909''', E800'44.951'', from an altitude of 798m. By employing the Ohmega Meter and Schlumberger configuration, four VES points are sounded for subsurface structure characterisation. Thereafter, a cylindrical steel ring is hammered into the ground at the first point (VES 1) and earth samples are scooped from this location; this procedure is repeated for other points (VES 2, 3 and 4). Winresist, Geo-earth, and Surfer version 12.0.626 software are employed to generate geo-sections, lithology, resistivity profile, Iso resistivity and Isopach maps, of the region. Outcome of results reveal some lithological formations of lateritic topsoil, fractured basement and fresh basement; additionally, results reveal 206.6m, 90.7m, 73.2m and 99.4m fractured basement thicknesses for four points. Scooped samples are transferred to the specimen stage of a Scanning Electron Microscope (SEM). SEM images show rounded inter-granular boundaries—the granular structures act like micro-wheels making the upper crustal mass susceptible to movement at the slightest vibration. Collapsed buildings are sited around VES1 location; samples from VES 1 are the most well fragmented sample owing to multiple microfractures—this result explains why VES 1 has the thickest fractured basement. Abrupt frictional sliding occurs between networks of fault lines; there is a likelihood that friction is most intense at the rock slide site on N9027'21.516'' and E800'44.9993'', VES 1 at N9027'5.819'' and E8005'3.1120'' and smoke sites—holo-centres are suspected below these locations. The presence of borehole facilities and quarry activities around the region serve as artificial causal factors of these tremors.

Stratigraphy, facies architecture, and palaeoenvironment of Neoproterozoic volcanics and volcaniclastic deposits in Fatira area, Central Eastern Desert, Egypt

NASA Astrophysics Data System (ADS)

Khalaf, Ezz El Din Abdel Hakim

Fatira area in the Central Eastern Desert, Egypt, is a composite terrane consisting of Neoproterozoic volcanics and sediments laid down in submarine to subaerial environment, intruded by voluminous old to young granitic rocks. The various lithofacies of the study area can be grouped in three distinct lithostratigraphic sequences, which are described here in stratigraphic order, from base to top as the Fatira El Beida, Fatira El Zarqa and Gabal Fatira sequences. Each depositional sequence, is intimately related to volcanic activity separated by time intervals of volcanic inactivity, such as marked hiatuses, reworked volcaniclasts, and or turbidite sedimentation. Four submarine facies groups have been recognized within the oldest, folded eruption sequence of Fatira El Beida. The southern part of the study area is occupied by sheet lava (SL), pillow lavas (PL), pillow breccias (PB), and overlying Bouma turbiditic volcaniclastites (VC). The four facies groups of Fatira El Beida sequence occur in a predictable upward-deepening succession, essentially from base to top, an SL-PL-PB-VC stacking pattern. The coeval tholeiitic mafic and felsic volcaniclastic rocks of this sequence indicate an extensional back-arc tectonic setting. The El Beida depositional sequence appears to fit a submarine-fan and slope-apron environment in an intra-arc site. The Fatira El Zarqa sequence involves a large volume of subaerial calc-alkaline intermediate to felsic volcanics and an unconformably overlying siliciclastic succession comprising clast-supported conglomerates (Gm), massive sandstone sheet floods (Sm) and mudstones (FI), together with a lateritic argillite paleosol (P) top formed in an alluvial-fan system. The youngest rock of Gabal Fatira sequence comprises anorogenic trachydacites and rhyolites with locally emergent domes associated with autobrecciation and sill-dyke rock swarms that could be interpreted as feeders and subvolcanic intrusions. Unconformity and lithofacies assemblages define seven events and three unconformity-bounded tectonic stages that record uplift-subsidence cycles in the study area. A proximal-distal relationship has been established within the depositional products, based on the relative dominance of erosional and depositional features.

Colours Convey Lanna Identity in Lamphun and Chiang Mai Area

NASA Astrophysics Data System (ADS)

Raksawin, Karuna; Wonglaksanapan, Arphaphon; Suthasupa, Supagtra

2017-10-01

Colour control is a specific tool to identify local environment. Especially in the historic area or conservation area, to promote colour control is very necessary. Therefore, there are many standards of colour to control such as Munsell, colour name, and L*a*b*. This research is aimed to analyze the appropriate colour control by using a Munsell standard colour which is suitable to visual perception. The study area is scoped in northern region of Lanna culture in Thailand which nowadays used names of colours to control. Chiang Mai and Lamphun are selected to be case study because they are in a center of Lanna Empire of Thailand and have many historic significant things such as city wall, temple, monastery, palace, and city moat. The mainly procedure conducts in this article is based on the analysis of material colour. The study chose local natural materials which are used in the historic significant things. Earthen clay tile, wooden roof tile, burnt clay brick, laterites, hard wood, bamboo, silver, and gold are evaluated. The procedure used the DIC application of android processor on smart phone. This application has a conversion data to switch a colour value from pick-up point in photo to many colour values such as RGB, CMYK which Munsell value is included. The photos were taken within the historic area of Chiang Mai and Lamphun by random. The result can scope a range of colours of Munsell standard of natural colour (N), red (R), yellow (Y), and yellow-red (YR). A natural colour (N) can be suggested a range 1.0-9.0 (N 1.0-9.0). Red can be ranged the value between 3.0-7.0 and chroma between 3.0-9.0 (R 3.0-7.0/3.0-9.0). Yellow can be ranged the value between 6.0-9.0 and chroma between 4.0-12.0 (Y 6.0-9.0/4.0-12.0). Yellow-red can be ranged the value between 2.0-8.0 and chroma between 2.0-11.0 (YR 2.0-8.0/2.0-11.0). The results can be revealed a process of colour analysis of historic colour control and may offer to be an ordinance in further.

Reconstructing sacred landscapes from soils-based records

NASA Astrophysics Data System (ADS)

Simpson, Ian; Gilliland, Krista; Coningham, Robin; Manuel, Mark; Davis, Christopher; Strickland, Keir; Acharya, Kosh; Hyland, Katherine; Bull, Ian; Kinnaird, Timothy; Sanderson, David

2015-04-01

From soils- and sediments- based records we reconstruct development of the sacred landscape at Lumbini UNESCO World Heritage Site in the central Nepalese Terai, the birthplace of Buddha, a world religion and now a major place of pilgrimage to its temple site. The Terai is a plain less than 100 m above sea level with incising rivers that originate in the Churia Hills and flow to the Ganges. Alluvial sediments on the Terai plain, originating as laterite soils within the hills, are characterised by a range of textural classes rich in iron oxides and manganese, with sandier sediments near water sources and finer textures near the distal ends of alluvial reaches. Our objectives are to establish a chronological framework for occupation, identify influences of alluvial environments on site occupation and determine the process of secular and sacred site formation within the World Heritage Site. A set of key stratigraphies are the basis for our analyses and are located in a palaeo-channel adjacent the temple site, within the temple site itself, and within the mound of the original Lumbini village. Optically stimulated luminescence (OSL) measurements of soils and sediments together with supporting single entity radiocarbon measurements provide robust chronological frameworks. Assessment of field properties, thin section micromorphology and organic biomarkers offer new insight into the intimate and complex relationships between natural, cultural and culturally mediated processes in landscape development. Integration of our findings allows a detailed narrative of cultural landscape development at Lumbini. The area was occupied from ca. 1,500 BC first of all by a transient community who used the area for product storage and who were subject to persistent flooding with periodic major flood events. Subsequent occupation deliberately raised a permanent village settlement above the level of flood events flooding and which had associated managed field cultivation. Village life was well established by the time of the Buddha's birth. Dating of the early and previously unknown temple site indicates a birth date of ca. 550 BC. Reconstruction of the early temple site indicates an enclosed open space with tree cover that was further elaborated with a surrounding walkway and cover during a later phase of construction. Triterpeniod and wax ester soil biomarkers indicate that the tree cover was most likely Ficus religiosa (Pipal). The study offers the first geoarchaeological investigation of Lumbini and the implications this carries for the understanding of international heritage and its conservation.

Planation surfaces as a record of medium to large wavelength deformation: the example of the Lake Albert Rift (Uganda) on the East African Dome

NASA Astrophysics Data System (ADS)

Brendan, Simon; François, Guillocheau; Cécile, Robin; Jean, Braun; Olivier, Dauteuil; Massimo, Dall'Asta

2016-04-01

African relief is characterized by planation surfaces, some of them of continental scale. These surfaces are slightly deformed according to different wavelengths (x10 km; x100 km, x1000 km) which record both mantle dynamics (very long wavelength, x 1000 km) and lithosphere deformation (long wavelength deformation, x 100 km). Different types of these planation surfaces are recognized: - Etchplains capped by iron-duricrust which correspond to erosional nearly flat weathered surfaces resulting from the growth of laterites under warm and humid conditions. - Pediments which define mechanical erosional surfaces with concave or rectilinear profiles delimited by upslope scarps connected upstream with the upper landforms. We here focused on the Lake Albert Rift at the northern termination of the western branch of the East African Rift System of which the two branches are surimposed on the East-African Dome. Different wavelengths of deformation were characterized based on the 3D mapping of stepped planation surfaces: (1) very long wavelength deformations resulting from the uplift of the East African Dome; (2) long wavelength deformations resulting from the opening of the eastern branch and (3) medium wavelength deformations represented by the uplift of rift shoulders like the Rwenzori Mountains. The paleo-landscape reconstruction of Uganda shows the existence of four generations of landforms dated according to their geometrical relationships with volcanic rocks. A four stepped evolution of the Ugandan landforms is proposed: • 70 - 22 Ma: generation of two weathered planation surfaces (etchplain Uw and Iw). The upper one (Uw) records a very humid period culminating at time of the Early Eocene Climatic Optimum (70-45 Ma). It corresponds to the African Surface. A first uplift of the East African Dome generates a second lower planation surface (Iw) connected to the Atlantic Ocean base level; • 17-2.7 Ma: planation of large pediplains connected to the local base level induced by the birth of the Albertine Rift System and the formation of the proto-Lake Albert; • 2.7-0.4 Ma: uplift of the Ruwenzori Mountains and degradation by river incision of the previous large pediplains; • 0.4-0 Ma: long wavelength downwarping of the Tanzania Craton between the two branches of the rift, creation of the Victoria Lake, inversion of the drainage and formation of the fault-bounded scarps of Albert Rift.

Reevaluation of 1935 M 7.0 earthquake fault, Miaoli-Taichung Area, western Taiwan: a DEM and field study

NASA Astrophysics Data System (ADS)

Lin, Y. N.; Chen, Y.; Ota, Y.

2003-12-01

A large earthquake (M 7.0) took place in Miaoli area, western Taiwan on April 21st, 1935. Right to its south is the 1999 Chi-Chi earthquake fault, indicating it is not only tectonically but seismically active. As the previous study, the study area is located in the mature zone of a tectonic collision that occurred between Philippine sea Plate and Eurasia continental Plate. The associated surface ruptures of 1935 earthquake daylighted Tungtsichiao Fault, a tear fault trending NE in the south and Chihhu Fault, a back thrust trending N-S in the north, but no ruptures occurred in between. Strike-slip component was identified by the horizontal offset observed along Tungtsichiao Fault; however, there are still disputes on the reported field evidence. Our purposes are (1) to identify the structural behaviors of these two faults, (2) to find out what the seismogenic structure is, and (3) to reconstruct the regional geology by information given by this earthquake. By DEM interpretation and field survey, we can clearly recognize a lot of the 1935 associated features. In the west of Chihhu Fault, a series of N-S higher terraces can be identified with eastward tilted surfaces and nearly 200 m relative height. Another lower terrace is also believed being created during the 1935 earthquake, showing an east-facing scarp with a height of ca. 1.5~2 m. Outcrop investigation reveals that the late-Miocene bedrock has been easterly thrusted over the Holocene conglomerates, indicating a west-dipping fault plane. The Tungtsichiao Fault cuts through a lateritic terrace at Holi, which is supposed developed in Pleistocene. The fault scarp is only discernible in the northeastern ending. Other noticeable features are the fault related antiforms that line up along the surface rupture. There is no outcrop to show the fault geometry among bedrocks. We re-interpret the northern Chihhu Fault as the back thrust generated from a main subsurface detachment, which may be the actual seismogenic fault. Due to the bend geometry normally existing between ramp and detachment, stress accumulated and earthquake happened right on it. The fault tip of this main thrust may be blind on land or break out offshore, which explains why no surface ruptures related to the main thrust were found.

Timing, tempo and paleoenvironmental influence of Deccan volcanism relative to the KT extinction

NASA Astrophysics Data System (ADS)

Adatte, Thierry; Keller, Gerta; Schoene, Blair; Khadri, Syed

2015-04-01

Deccan Traps erupted in three main phases with 6% total Deccan volume in phase-1 (base C30n), 80% in phase-2 (C29r) and 14% in phase-3 (C29n). Recent studies indicate that the bulk (80%) of Deccan trap eruptions (Phase-2) occurred over a relatively short time interval in magnetic polarity C29r (Chenet et al., 2008). Moreover, U-Pb zircon geochronology shows that the main Phase 2 began 250 ka before the Cretaceous-Tertiary (KT) mass extinction, suggesting a cause-and-effect relationship (Blair et al., 2015). In India a strong floral response is observed as a direct consequence of volcanic phase-2. In Lameta (infratrappean) sediments preceding the volcanic eruptions, palynoflora are dominated by gymnosperms and angiosperms (Samant and Mohabey, 2005). Shortly after the onset of Deccan phase-2, this floral association was decimated as indicated by a sharp decrease in pollen and spores coupled with the appearance of fungi, which mark increasing stress conditions apparently as a direct result of volcanic activity. The inter-trappean sediments corresponding to the Phases 2 and 3 are characterized by the highest alteration CIA index values suggesting increased acid rains due to SO2 emissions. Closer to the eruption center, the lava flows are generally separated by red weathered horizons known as red boles, marking a quiescent period between two basalt flows. Red boles consist mainly of red silty clays characterized by concentrations of immobile elements such as Al and Fe3+ ions, which provide indirect evidence of a primitive form of paleo-laterite that probably developed during the short periods of weathering between eruptions. There are at least 15 thick red bole layers in C29r below the KT boundary, and all were deposited in phase-2 volcanic eruptions that occurred over a time span of about 250 ky. These short duration exposures are reflected in the mineralogical and geochemical data that indicate rapid weathering (high CIA) but arid conditions. The arid conditions can be explained by acid rain, which accelerated the weathering process. These observations indicate that Deccan volcanism played a key role in increasing atmospheric CO2 and SO2 levels that resulted in global warming and acidified oceans, thus increasing biotic stress that predisposed faunas to eventual extinction at the KTB.

Foundation integrity assessment using integrated geophysical and geotechnical techniques: case study in crystalline basement complex, southwestern Nigeria

NASA Astrophysics Data System (ADS)

Olayanju, G. M.; Mogaji, K. A.; Lim, H. S.; Ojo, T. S.

2017-06-01

The determination of parameters comprising exact depth to bedrock and its lithological type, lateral changes in lithology, and detection of fractures, cracks, or faults are essential to designing formidable foundations and assessing the integrity of civil engineering structures. In this study, soil and site characterization in a typical hard rock geologic terrain in southwestern Nigeria were carried out employing integrated geophysical and geotechnical techniques to address tragedies in civil engineering infrastructural development. The deployed geophysical measurements involved running both very low frequency electromagnetic (VLF-EM) and electrical resistivity methods (dipole-dipole imaging and vertical electrical sounding (VES) techniques) along the established traverses, while the latter technique entailed conducting geological laboratory sieve analysis and Atterberg limit-index tests upon the collected soil samples in the area. The results of the geophysical measurement, based on the interpreted VLF-EM and dipole-dipole data, revealed conductive zones and linear features interpreted as fractures/faults which endanger the foundations of public infrastructures. The delineation of four distinct geoelectric layers in the area—comprised of topsoil, lateritic/clayey substratum, weathered layer, and bedrock—were based on the VES results. Strong evidence, including high degree of decomposition and fracturing of underlying bedrock revealed by the VES results, confirmed the VLF-EM and dipole-dipole results. Furthermore, values in the range of 74.2%-77.8%, 55%-62.5%, 23.4%-24.5%, 7.7%-8.2%, 19.5%-22.4%, and 31.65%-38.25% were obtained for these geotechnical parameters viz soil percentage passing 0.075 mm sieve size, liquid limit, plasticity index, linear shrinkage, natural moisture content, and plastic limit, respectively, resulting from the geotechnical analysis of the soil samples. The comparatively analyzed geophysical and geotechnical results revealed a high weathering of charnockitic rocks resulting in plastic clay material mapped with a mean resistivity value of 73 Ohm-m, in conformity with the obtained geotechnical parameters, which failed to agree with the standard specification of subsoil foundation materials and which, in turn, can impact negatively on the foundational integrity of infrastructures. Based on these results, the area subsoils’ competence for foundation has been rated poor to low. This study has more widely demonstrated the effective application of integrative geophysical and geotechnical methods in the assessment of subsoil competence.

A Miocene wave-dominated estuarine system in the Paraíba Basin, northeastern Brazil

NASA Astrophysics Data System (ADS)

Gandini, Rosana; Rossetti, Dilce de Fátima; Netto, Renata Guimarães; Góes, Ana Maria

2017-11-01

A number of publications have documented the effect of the Miocene transgression on several coasts of the world. However, this event is incompletely documented along the Brazilian margin, despite the existence of an impressive record of Miocene deposits exposed mostly as several coastal cliffs along more than 5000 km of distance. The transgressive nature of Miocene deposits, so far recognized only in a few localities of northeastern Brazil, needs to be amplified in order to better characterize the impact of the Miocene transgression in eastern South America. In this work, we provide facies analysis of early/middle Miocene strata exposed in the Paraíba Basin, northeastern Brazil, aiming reconstruct the depositional paleoenvironments and analyze their evolution within the context of relative sea-level fluctuations data. The results revealed deposits characterized by several features that were related to the action of tidal currents, such as alternating thicker/thinner forest packages, abundant reactivation surfaces, mud drapes and oppositely-dipping (herringbone) cross sets. These sedimentary structures were associated with an ichnological assemblage indicative of marine-influenced and brackish water, best represented by Ophiomorpha, Planolites-Palaeophycus-Thalassinoides and Thallassinoides-Planolites-Palaeophycus ichnofabrics. Sedimentation occurred in environments consisting of estuarine channel, estuarine central basin, tidal inlet/tidal channel, tidal delta/washover, tidal flat/shoal and foreshore, which were related to an estuarine setting, at least in part of a wave-dominated type. Analysis of facies stratal patterns led to suggest that the estuarine deposits of the Paraíba Basin reflect a rise in relative sea level probably during the transgressive and/or highstand stage of a depositional sequence formed directly overlying Cretaceous rocks. This rise can be correlated with the worldwide early/mid Miocene marine transgression. However, while the eustatic sea level remained rising through the middle Miocene, the estuarine sedimentation in the study area was cut off, being replaced by a regional unconformity marked by lateritic paleosols. Thus, a relative sea-level fall is recorded in the Paraíba Basin while the eustatic sea level remained rising through the middle Miocene, before its fall in the Tortonian. It follows that other factors, such as tectonics, is proposed to explain the mid-Miocene fall in sea level along the Paraíba coast, while the eustatic sea level was rising.

Rhodolith-forming coralline red algae from New Caledonia (SW Pacific) record half a century of sea-surface temperature variations and mining history

NASA Astrophysics Data System (ADS)

Darrenougue, N.; De Deckker, P.; Eggins, S. M.; Payri, C. E.; Fallon, S. J.

2011-12-01

We present a continuous, high-resolution tropical record of Mg/Ca and trace elements back to the 1960s, using laser ablation ICP-MS on rhodoliths (i.e. free living forms of coralline red algae) of the species Sporolithon durum. The analysed rhodoliths are composed entirely of branched system forming mostly spherical specimens of 8-10 cm in diameter. Chronology was constrained by 20 radiocarbon dates calibrated with the 1960s-70s atomic bomb-spike curve, in conjunction with commonly used growth band counting and Mg/Ca minima-maxima peaks. Mg/Ca variations are reproducible between different branches of a single specimen as well as between three distinct rhodoliths from the same site in the SW lagoon of New Caledonia. All records present a significant correlation with the local sea-surface temperatures at a monthly to inter-annual resolution (respectively, 0.59< r <0.70 and 0.62< r <0.72; p<0.0001), thus confirming the global potential of coralline red algae for palaeo-temperature reconstructions, as suggested by recent studies from the North Atlantic and North Pacific Oceans (e.g. Halfar et al. 2000, Kamenos et al. 2008, Hetzinger et al., 2009). Compared to the youngest part of the record, Mn/Ca, Fe/Ca and Ni/Ca ratios present significantly higher values for the period prior to 1980, which corresponds to the high production period of an open-air, Ni-extraction mine located in the water catchment area of the Coulée River, ~10km from the studied rhodolith bed. The mining production at the site ceased in 1981. After that date, Mn, Fe and Ni concentrations in the rhodoliths show a steady decline. Co/Ca, however, shows no such trend, indicating different behaviour and availability for these metals, all related to the weathering of exposed laterite formations. Average metal records corrected from the anthropogenic mining effect (except for Co/Ca) present significant correlations with the inter-annual local rainfall signal (r=0.62, r=0.60, r=0.48; p<0.0001 for Mn/Ca, Fe/Ca and Ni/Ca, respectively) for most of the studied period, in accordance with a freshwater-derived origin of the metals at the study site. This also suggests a potential use of metal concentrations in rhodoliths as an indirect tracer for local rainfall patterns.

Geology of uranium in the Chadron area, Nebraska and South Dakota

USGS Publications Warehouse

Dunham, Robert Jacob

1961-01-01

The Chadron area covers 375 square miles about 25 miles southeast of the Black Hills. Recurrent mild tectonic activity and erosion on the Chadron arch, a compound anticlinal uplift of regional extent, exposed 1900 feet of Upper Cretaceous rocks, mostly marine shale containing pyrite and organic matter, and 600 feet of Oligocene and Miocene rocks, mostly terrestrial fine-grained sediment containing volcanic ash. Each Cretaceous formation truncated by the sub-Oligocene unconformity is stained yellow and red, leached, kaolinized, and otherwise altered to depths as great as 55 feet. The composition and profile of the altered material indicate lateritic soil; indirect evidence indicates Eocene(?) age. In a belt through the central part of the area, the Brule formation of Oligocene age is a sequence of bedded gypsum, clay, dolomite, and limestone more than 300 feet thick. Uranium in Cretaceous shale in 58 samples averages 0.002 percent, ten times the average for the earths crust. Association with pyrite and organic matter indicates low valency. The uranium probably is syngenetic or nearly so. Uranium in Eocene(?) soil in 43 samples averages 0.054 percent, ranging up to 1.12 percent. The upper part of the soil is depleted in uranium; enriched masses in the basal part of the soil consist of remnants of bedrock shale and are restricted to the highest reaches of the ancient oxidation-reduction interface. The uranium is probably in the from of a low-valent mineral, perhaps uraninite. Modern weathering of Cretaceous shale is capable of releasing as much as 0.780 ppm uranium to water. Eocene(?) weathering probably caused enrichment of the ancient soil through 1) leaching of Cretaceous shale, 2) downward migration of uranyl complex ions, and 3) reduction of hydrogen sulfide at the water table. Uranium minerals occur in the basal 25 feet of the gypsum facies of the Brule formation at the two localities where the gypsum is carbonaceous; 16 samples average 0.066 percent uranium and range up to 0.43 percent. Elsewhere uranium in dolomite and limestone in the basal 25 feet of the gypsum facies in 10 samples averages 0.007 percent, ranging up to 0.12 percent. Localization of the uranium at the base of the gypsum facies suggests downward moving waters; indirect evidence that the water from which the gypsum was deposited was highly alkaline suggests that the uranium was leached from volcanic ash in Oligocene time.

A geochronological 40Ar/39Ar and 87Rb/81Sr study of K-Mn oxides from the weathering sequence of Azul, Brazil

NASA Astrophysics Data System (ADS)

Ruffet, G.; Innocent, C.; Michard, A.; Féraud, G.; Beauvais, A.; Nahon, D.; Hamelin, B.

1996-06-01

KMn oxides of hollandite group minerals such as cryptomelane (K 1-2(Mn 3+, Mn 4+) 8O 16nH 2O) are often precipitated authigenically in weathering profiles. The presence of structural K allows these minerals to be dated by the KAr and 40Ar/ 39Ar methods, making it possible to study the progression of oxidation fronts during weathering processes. Within the context of a recent 40Ar/ 39Ar study of cryptomelane from the Azul Mn deposit in the Carajàs region (Amazônia, Brazil), Vasconcelos et al. (1994) defined three age clusters (65-69, 51-56, and 40-43 Ma) and proposed that they correspond to the episodic precipitation of the three generations of Mn oxide that have been identified in the deposit (Beauvais et al., 1987). We performed a laser probe 40Ar/ 39Ar and 87Rb/ 87Sr study on new samples from the same Mn deposit. Our 40Ar/ 39Ar data confirm that cryptomelane is a suitable mineral for 40Ar/ 39Ar dating, although in some cases we clearly identify the existence of 39Ar recoil effects. Although the corresponding age spectra are generally strongly disturbed, our results also confirm that the earliest cryptomelane generation is of Upper Cretaceous-Paleocene age. We obtained good plateau ages from veins and concretions of the second cryptomelane generation. Some of these results allow definition of a well-constrained age cluster at 46.7-48.1 Ma not observed by Vasconcelos et al. (1994). A petrographic study confirms that none of the samples analyzed in the present study contained material associated with the third generation of cryptomelane. We propose that these new results support the idea of a more or less continuous crystallization of KMn oxides, mainly constrained by local factors, rather than the model advanced by Vasconcelos et al. (1994), which suggests that each cryptomelane generation corresponds to distinct weathering events related to global climatic changes. 87Sr/ 86Sr data show large variations, clearly inherited from the 2.1 Ga parent rock of the Mn protore. The Rb/Sr results demonstrate that minimum fractionation occurs during cryptomelane crystallization, except for the latest generation, which is depleted in Sr. This precludes use of the Rb/Sr radiochronometer for dating secondary Mn oxides in laterites.

Characterization of diagenetic siderites formed in recent and ancient ferruginous sediments of Lake Towuti, Indonesia.

NASA Astrophysics Data System (ADS)

Vuillemin, Aurele; Kallmeyer, Jens; Wagner, Dirk; Kemnitz, Helga; Wirth, Richard; Luecke, Andreas; Mayr, Christoph

2016-04-01

Authigenic minerals in lacustrine settings can be formed in the water column and within the sediment, abiotically and/or triggered by biological activity. Such minerals have been used as paleosalinity and paleoproductivity proxies, reflecting trophic state, and/or early diagenetic conditions. They have also been considered as potential biosignatures of past and present microbial activity. Here we present a study from Lake Towuti, a deep tectonic basin in Sulawesi, Indonesia. Its geographic position makes it a prime location to record paleoclimatic changes in the tropical Western Pacific warm pool in its sedimentary sequence. The ultramafic rocks and surrounding lateritic soils in the catchment area supply considerable amounts of iron and other metals to the lake. These elements further restrain primary productivity along with the development of specific microbial metabolic pathways involved in early diagenesis. Lake Towuti is stratified with anoxic conditions below 130 m, allowing metal reduction processes to take place in the hypolimnion. The extreme scarcity of sulphate and nitrate/nitrite make Lake Towuti's bottom waters a modern analogue for the Archaean Ocean. It was therefore chosen as a drilling target by the International Continental Drilling Program (ICDP). In May to July 2015, the Towuti Drilling Project recovered a total >1000 m of sediment core from three drilling sites, including a 114 m long core drilled with a contamination tracer dedicated to geomicrobiological studies. Heavy mineral fractions were extracted from core catcher samples and siderite crystals (FeCO3) were selected from different depths. Characterization of their habitus was achieved via SEM and TEM imaging. Preliminary results show that siderites grow from amorphous into nanocrystalline phases and form twinned aggregates developing into mosaic monocrystals with depth. Gradual filling of vugs and microporosity were observed along with inclusions of magnetite nanocrystals. Work in progress includes parallel δ13C measurements on bulk organic matter (OM) surrounding the minerals and on the siderites themselves to trace organic to inorganic carbon transfer associated with microbial respiration of OM and infer possible relationships to methane oxidation processes. Analysis of δ56Fe compositions will complement this dataset to highlight the role of dissimilatory Fe (III) reduction in siderite formation. We hypothesize that sedimentary siderite is formed by precipitation from pore water due to saturation resulting from microbial OM and iron respiration processes. A similar approach will be applied to vivianite crystals (Fe3(PO4)3ṡ8H2O) that were found concomitantly with siderite in sedimentary horizons intercalated with tephra layers.

Metallic elements and metalloids in Boletus luridus, B. magnificus and B. tomentipes mushrooms from polymetallic soils from SW China.

PubMed

Falandysz, Jerzy; Zhang, Ji; Wiejak, Anna; Barałkiewicz, Danuta; Hanć, Anetta

2017-08-01

Yunnan Province in China is known for its high biodiversity of mushrooms and a diverse geochemistry of soil bedrock and polymetallic soils, but our knowledge of mineral compositions of mushrooms from Yunnan is scarce. The metallic trace elements, Ag, Ba, Co, Cd, Cs, Cu, Cr, Hg, Li, Mn, Ni, Pb, Rb, Sr, V, Tl, U and Zn, and the metalloids, As and Sb, have been investigated using validated methods with a dynamic reactive cell by mass spectroscopy - inductive coupled plasma and cold vapour - atomic absorption spectroscopy on three popular species of Boletus mushrooms from Southwestern China. The trace mineral profiles in caps and stipes of B. luridus (24 individuals), B. magnificus (29 individuals) and B. tomentipes (38 individuals) have been evaluated. The interspecific differences in the content of several trace elements could be attributed to known differences in the geochemistry of soils in Yunnan, but for copper a difference was observed within species. The mean values of concentrations in composite samples of caps for B. luridus, B. magnificus and B. tomentipes from three to four locations were at the ranges (mgkg -1 dry biomass): Ag (1.3-3.7), As (0.79-53), Ba (4.0-12), Co (0.68-1.2), Cd (0.79-2.2), Cs (0.67-55), Cu (37-77), Cr (5.0-7.6), Hg (2.1-5.4), Li (0.15-0.61), Mn (13-28), Ni (0.86-4.6), Pb (0.59-1.8), Rb (90-120), Sb (0.014-0.088), Sr (0.63-1.6), V (1.4-2.2), Tl (0.017-0.054), U (0.029-0.065) and Zn (130-180). Caps of Boletus mushrooms were richer in Ag, Cu, Hg and Zn than stipes, while other elements were distributed roughly equally between both morphological parts. B. luridus, B. magnificus and B. tomentipes grew in certain sites in Yunnan contained Ag, As, Ba, Cr, Hg, Ni, Sr or V at elevated concentration. A specific geochemistry of the soils type (latosols, lateritic red earths, and red and yellow earths in the Circum-Pacific Mercuriferous Belt of Southwestern China) can explain occurrence of some minerals at greater or elevated amount in mushrooms in Yunnan, while number of available research and data on mineral composition of mushrooms due to geochemical anomalies of soil parent material is so far little. Copyright © 2017 Elsevier Inc. All rights reserved.

Nanoparticles of noble metals in the supergene zone

NASA Astrophysics Data System (ADS)

Zhmodik, S. M.; Kalinin, Yu. A.; Roslyakov, N. A.; Mironov, A. G.; Mikhlin, Yu. L.; Belyanin, D. K.; Nemirovskaya, N. A.; Spiridonov, A. M.; Nesterenko, G. V.; Airiyants, E. V.; Moroz, T. N.; Bul'bak, T. A.

2012-04-01

Formation of noble metal nanoparticles is related to various geological processes in the supergene zone. Dispersed mineral phases appear during weathering of rocks with active participation of microorganisms, formation of soil, in aqueous medium and atmosphere. Invisible gold and other noble metals are incorporated into oxides, hydroxides, and sulfides, as well as in dispersed organic and inorganic carbonic matter. Sulfide minerals that occur in bedrocks and ores unaltered by exogenic processes and in cementation zone are among the main concentrators of noble metal nanoparticles. The ability of gold particles to disaggregate is well-known and creates problems in technological and analytical practice. When Au and PGE nanoparticles and clusters occur, these problems are augmented because of their unusual reactions and physicochemical properties. The studied gold, magnetite, titanomagnetite and pyrite microspherules from cementation zone and clay minerals of laterites in Republic of Guinea widen the knowledge of their abundance and inferred formation conditions, in particular, in the contemporary supergene zone. Morphology and composition of micrometer-sized Au mineral spherules were studied with SEM and laser microprobe. The newly formed segregations of secondary gold on the surface of its residual grains were also an object of investigation. The character of such overgrowths is the most indicative for nanoparticles. The newly formed Au particles provide evidence for redistribution of ultradispersed gold during weathering. There are serious prerequisites to state that microorganisms substantially control unusual nano-sized microspherical morphology of gold particles in the supergene zone. This is supported by experiments indicating active absorption of gold by microorganisms and direct evidence for participation of Ralstonia metallidurans bacteria in the formation of peculiar corroded bacteriomorphic surface of gold grains. In addition, the areas enriched in carbon and nitrogen have been detected with SEM on the surface of gold spherules from Guinea. Such organic compounds as serine, alanine, and glycine are identified on their surface with Raman spectroscopy. The experiments have been carried out and new data have been obtained indicating the role of micromycetes in concentration and distribution of noble metals in ferromanganese nodules of the World Ocean. Au and Pt were detected in the system with radioisotopes. It has been established that two forms of gold distribution develop within pseudomorphs of fungi colonies: (1) as pseudomorphic concentrates and (2) dispersed form unrelated to the colony structure. Inhomogeneities in distribution of dispersed platinum are manifested in the form of linear anomalies with elevated concentrations at the margins of the colonies.

Mining hydrogeological data from existing AEM datasets for mineral Mining

NASA Astrophysics Data System (ADS)

Menghini, Antonio; Viezzoli, Andrea; Teatini, Pietro; Cattarossi, Andrea

2017-04-01

Large amount of existing Airborne Electromagnetic (AEM) data are potentially available all over the World. Originally acquired for mining purposes, AEM data traditionally do not get processed in detail and inverted: most of the orebodies can be easily detected by analyzing just the peak anomaly directly evidenced by voltage values (the so-called "bump detection"). However, the AEM acquisitions can be accurately re-processed and inverted to provide detailed 3D models of resistivity: a first step towards hydrogeological studies and modelling. This is a great opportunity especially for the African continent, where the detection of exploitable groundwater resources is a crucial issue. In many cases, a while after AEM data have been acquired by the mining company, Governments become owners of those datasets and have the opportunity to develop detailed hydrogeological characterizations at very low costs. We report the case in which existing VTEM (Versatile Time Domain Electromagnetic - Geotech Ltd) data, originally acquired to detect gold deposits, are used to improve the hydrogeological knowledge of a roughly 50 km2 pilot-test area in Sierra Leone. Thanks to an accurate processing workflow and an advanced data inversion, based on the Spatially Constrained Inversion (SCI) algorithm, we have been able to resolve the thickness of the regolith aquifer and the top of the granitic-gneiss or greenstone belt bedrock. Moreover, the occurrence of different lithological units (more or less conductive) directly related to groundwater flow, sometimes having also a high chargeability (e.g. in the case of lateritic units), has been detailed within the regolith. The most promising areas to drill new productive wells have been recognized where the bedrock is deeper and the regolith thickness is larger. A further info that was considered in hydrogeological mapping is the resistivity of the regolith, provided that the most permeable layers coincide with the most resistive units. The resistivity model thus produced has allowed us to detect some alignments of conductive dykes, perforating the greenstone belt (made by volcanic Mafic and Ultramafic rocks or Metasedimentary formations), and correlated with the gold mineralization. Moreover, the conductive response of the basal serpentine-chloritized Ultramafic volcanic rocks, has allowed reconstructing the deeper structural features of the area. Therefore, the advantage in re-processing existing AEM data has been twofold, i.e. for both hydrogeological and geological-structural (hence mining) purposes. Concluding, we advocate for re-using of existing AEM datasets covering wide areas in underdeveloped and developing countries in to improve the hydrogeological characterizations of these nations where groundwater resources could cope with need of providing fresh / safe water to the population.

Stages of weathering mantle formation from carbonate rocks in the light of rare earth elements (REE) and Sr-Nd-Pb isotopes

NASA Astrophysics Data System (ADS)

Hissler, Christophe; Stille, Peter

2015-04-01

Weathering mantles are widespread and include lateritic, sandy and kaolinite-rich saprolites and residuals of partially dissolved rocks. These old regolith systems have a complex history of formation and may present a polycyclic evolution due to successive geological and pedogenetic processes that affected the profile. Until now, only few studies highlighted the unusual high content of associated trace elements in weathering mantles originating from carbonate rocks, which have been poorly studied, compared to those developing on magmatic bedrocks. For instance, these enrichments can be up to five times the content of the underlying carbonate rocks. However, these studies also showed that the carbonate bedrock content only partially explains the soil enrichment for all the considered major and trace elements. Up to now, neither soil, nor saprolite formation has to our knowledge been geochemically elucidated. Therefore, the aim of this study was to examine more closely the soil forming dynamics and the relationship of the chemical soil composition to potential sources. REE distribution patterns and Sr-Nd-Pb isotope ratios have been used because they are particularly well suited to identify trace element migration, to recognize origin and mixing processes and, in addition, to decipher possible anthropogenic and/or "natural" atmosphere-derived contributions to the soil. Moreover, leaching experiments have been applied to identify mobile phases in the soil system and to yield information on the stability of trace elements and especially on their behaviour in these Fe-enriched carbonate systems. All these geochemical informations indicate that the cambisol developing on such a typical weathering mantle ("terra fusca") has been formed through weathering of a condensed Bajocian limestone-marl facies. This facies shows compared to average world carbonates important trace element enrichments. Their trace element distribution patterns are similar to those of the soil suggesting their close genetic relationships. Sr-Nd-Pb isotope data allow to identify four principal components in the soil: a silicate-rich pool at close to the surface, a leachable REE enriched pool at the bottom of the soil profile, the limestone facies on which the weathering profile developed and an anthropogenic, atmosphere-derived component detected in the soil leachates of the uppermost soil horizon. The leachable phases are mainly secondary carbonate-bearing REE phases such as bastnaesite. The isotope data and trace element distribution patterns indicate that at least four geological and environmental events impacted the chemical and isotopical compositions of the soil system since the Cretaceous.

Unusual Rocks of the Yap Ridge - Metamorphosed Basal Cumulates of an Arc ?

NASA Astrophysics Data System (ADS)

Hawkins, J. W.; Castillo, P. R.; Batiza, R.

2002-12-01

The 8 to 9 km deep Yap trench, and adjacent Yap Ridge, extend from the southwest end of the Mariana Trench near 11o N, to near 7o 15' N where the trench swings west to intersect the Palau Trench. Unlike other western Pacific subduction systems, the Yap Ridge rises directly from the trench, it has no forearc, neither a remnant nor active volcanic arc, and no inclined seismic zone. The few seismic events recorded are mainly < 70 km depth. Yap Ridge crest depths range from 2.5 km to emergent; there are no emergent volcanoes. Rocks from the islands Yap and Map, are mainly strongly schistose, amphibole-rich, mafic and ultramafic rocks. Metamorphic lineations, and meter-sized mullions having lenticular cross-sections, define inclined (15o southerly dip) tectonic transport. Yap and Map schists are in greenschist facies (actinolite - chlorite - Na-plagioclase, rare titanite and epidote). Talc - tremolite schists, serpentinite, and chlorite-pyroxenite are less common. Small areas of altered andesite are present; quartz diorite and hornblende-rich gabbro occur as clasts in breccias, bomb craters yielded fragments of basalt and diabase. Scattered blankets of laterite several meters thick, and jungle, obscure many details. Deeper crustal rocks exposed on inner wall of Yap Trench, (5 - 2.5 km depths) include amphibolite (Al-hornblende-andesine-titanite) interlayered with calcite- diopside - grossularite marble, and calc-silicate gneisses. Rocks dredged from Yap Ridge include metabasite similar toYap schists, island arc tholeiite series basalt, basaltic andesite, and 2-PX gabbro. These have late Miocene ages (Beccaluva et al., AGU Mon. 23, 1980). Assuming isochemical behavior for immobile elements, protolith for mafic and ultramafic schists had high Mg# (52-83), CaO/Al2O3 0.7-6, Cr 288-1490, Ni 64-609, Zr 13-145, Y 3-28 (ppm).These data suggest picrite, high-Mg basalt, boninite, or OL-PX rich ultramafic cumulates as parents. REE data, e.g. negative slope and (La/Sm)N 0.9-1.9 indicate sub-arc PX-rich cumulates as a likely protolith (from late-Oligocene to late Miocene West Mariana Ridge ?). Basalt, andesite and gabbro have arc-like depleted HFSE and REE patterns. Yap Ridge crust probably formed in a subduction setting; the inactive trench is preserved but subduction has ended. Thick crust of the Caroline Ridge, lying outboard of the Yap Trench, may inhibit subduction. Yap Ridge schists may represent ultramafic cumulates metamorphosed when thrust over arc or forearc crust.

CZO perspective in Central Africa : The Lopé watershed, Lopé National Park, Ogooué River basin, Gabon.

NASA Astrophysics Data System (ADS)

Braun, J. J.; Jeffery, K.; Koumba Pambo, A. F.; Paiz, M. C.; Richter, D., Jr.; John, P.; Jerome, G.

2015-12-01

Critical Zone Observatories (CZO) in equatorial regions are seldom (see e. g. http://www.czen.org/, USA and http://rnbv.ipgp.fr/, France). The equatorial zone of Central Africa is almost free of them with the exception of the CZO of the Upper Nyong river basin (organic-rich river on the lateritic plateau of South Cameroon; SO BVET, http://bvet.omp.obs-mip.fr/). On both sides of the Equator line, the Ogooué River Basin (215,000 km2) stretches on about 80% of the total area of Gabon and drains various geological and morpho-pedological contexts and feeds the sedimentation areas of the Central African passive margin (Guillochaux et al., 2014). The Upper Ogooué (up to Lambaréné) drains the stepped planation surface of the Congo craton while the Lower Ogooué drains Mesozoic and Cenozoic sedimentary terrains. The climate is equatorial (Pmean = 2500 mm/yr; Tmean = 26 °; %humidity > 80%). Continuous hydro-climatic chronicles exist for the period 1953-1974 (managed by ORSTOM, now IRD). The runoff at Lambaréné (92% of the basin area) is very high (714 mm/yr). With a rural density of 1 inhabitant/km2, it is one of the last largely pristine tropical forested ecosystems on the Planet. In addition, the basin will be, in the coming decades, the theatre of important anthropogenic changes (dams, agriculture, mining, urbanisation, …). However, a conservation plan with an ambitious sustainable development policy is set up. This plan articulates the environmental issues related to the emergence of the country. Because of these characteristics, the basin offers ideal conditions for studying the changes in equatorial region of hydro-climate, weathering/erosion regimes and regolith production based on morpho-pedological contexts and associated physical, chemical and biological processes. It is thus germane to launch an integrated CZO initiative at both regional scale and local scale. At the regional scale, we plan to reactivate some of the hydro-climatic stations located on the planation surface (Franceville, Ayem, and Lambaréné). At the local scale, we plan to set up a small experimental watershed on the Lopé stream draining the northern part of the Lopé National Park, which is covered by a mosaic of forest and savannah. The Ogooué CZO will be highly complementary to the Nyong CZO, Cameroon, and a major asset for the international community.

Monitoring environmental risk in fibrous minerals in New Caledonia: a comparison between different analytical methods.

NASA Astrophysics Data System (ADS)

Petriglieri, Jasmine Rita; Laporte-Magoni, Christine; Salvioli-Mariani, Emma; Gunkel-Grillon, Peggy; Tribaudino, Mario; Mantovani, Luciana; Bersani, Danilo; Lottici, Pier Paolo; Tomatis, Maura

2017-04-01

The New Caledonia is covered by ultrabasic units for more than a third of its surface, and it is one of the largest world producers of nickel ore. Mining activity, focused on extraction from lateritic ore deposits formed by the alteration of ultramafic rocks, must deal with the natural occurrence of asbestos and fibrous minerals. Almost all outcrops of geological units in open mines contain serpentine and amphibole, also as asbestos varieties (Lahondère, 2007). Owing to humid tropical to sub-tropical conditions, weathering processes and supergene mineralization are one of the main responsible for fibrogenesis of asbestos minerals. The presence of fibrous minerals in mining and storage sites requires attention due to public health problems and for the safety of the operators. In this context, the evaluation of risk and health hazard to prevent the effects due to exposition is closely linked to the formation, alteration and release of fibers into the environment. It has been demonstrated that different fibrous minerals have different toxicity (Fubini & Otero-Arean, 1999; Fubini & Fenoglio, 2007). An analytical strategy to discriminate and characterize, with certainty, the different varieties of the asbestiform phases is required to the establishment of an environmental monitoring system. We have therefore analyzed by different methods a set of about fifty asbestos sampled for mapping environmental risk in fibrous minerals in New Caledonia. The samples contain serpentines (chrysotile, antigorite) and amphibole (tremolite), all fibrous and have been sorted by their different degree of alteration. Data obtained with the more traditional mineralogical and petrological analytical techniques - such as optical microscopy, X-ray diffraction, secondary electron microscopy (SEM-EDS), and transmission electron microscopy - have been completed by the employment of more specialized tools as phase contrast microscopy (PCM), Raman spectroscopy, and thermal analysis (DTA). Moreover analytical performances of a Raman portable equipment, to be used in field observation, were assessed against other laboratory methods. Portable Raman was tested first in laboratory to check its reliability, and then on fieldtrip, directly on the mining front under normal environmental conditions (sun, strong wind, high temperature, etc.). Thus, for each analytical method, ability for fibers identification was tested. This project is part of the French-Italian program "Amiantes et Bonnes Pratiques", financed by the CNRT "Nickel and its environment" of New Caledonia. Fubini, B., & Otero-Arean, C. (1999): Chemical aspects of the toxicity of inhaled mineral dusts. Chemical Society Reviews, 28(6), 373-381. Fubini, B., & Fenoglio, I. (2007): Toxic potential of mineral dusts. Elements, 3(6), 407-414. Lahondère, D. (2007): L'amiante environnemental en Nouvelle Calédonie: Expertise géologique des zones amiantifères. Evaluation des actions engagées. BRGM/RP-55894-FR, 55 p.

Cobalt

USGS Publications Warehouse

Slack, John F.; Kimball, Bryn E.; Shedd, Kim B.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Cobalt is a silvery gray metal that has diverse uses based on certain key properties, including ferromagnetism, hardness and wear-resistance when alloyed with other metals, low thermal and electrical conductivity, high melting point, multiple valences, and production of intense blue colors when combined with silica. Cobalt is used mostly in cathodes in rechargeable batteries and in superalloys for turbine engines in jet aircraft. Annual global cobalt consumption was approximately 75,000 metric tons in 2011; China, Japan, and the United States (in order of consumption amount) were the top three cobalt-consuming countries. In 2011, approximately 109,000 metric tons of recoverable cobalt was produced in ores, concentrates, and intermediate products from cobalt, copper, nickel, platinum-group-element (PGE), and zinc operations. The Democratic Republic of the Congo (Congo [Kinshasa]) was the principal source of mined cobalt globally (55 percent). The United States produced a negligible amount of byproduct cobalt as an intermediate product from a PGE mining and refining operation in southeastern Montana; no U.S. production was from mines in which cobalt was the principal commodity. China was the leading refiner of cobalt, and much of its production came from cobalt ores, concentrates, and partially refined materials imported from Congo (Kinshasa).The mineralogy of cobalt deposits is diverse and includes both primary (hypogene) and secondary (supergene) phases. Principal terrestrial (land-based) deposit types, which represent most of world’s cobalt mine production, include primary magmatic Ni-Cu(-Co-PGE) sulfides, primary and secondary stratiform sediment-hosted Cu-Co sulfides and oxides, and secondary Ni-Co laterites. Seven additional terrestrial deposit types are described in this chapter. The total terrestrial cobalt resource (reserves plus other resources) plus past production, where available, is calculated to be 25.5 million metric tons. Additional resources of cobalt are known to occur on the modern sea floor in aerially extensive deposits of Fe-Mn(-Ni-Cu-Co-Mo) nodules and Fe-Mn(-Co-Mo-rare-earth-element) crusts. Legal, economic, and technological barriers have prevented exploitation of these cobalt resources, which lie at water depths of as great as 6,000 meters, although advances in technology may soon allow production of these resources to be economically viable.Environmental issues related to cobalt mining concern mainly the elevated cobalt contents in soils and waters. Although at low levels cobalt is essential to human health (it is the central atom in the critical nutrient vitamin B12), overexposure to high levels of cobalt may cause lung and heart dysfunction, as well as dermatitis. The ecological impacts of cobalt vary widely and can be severe for some species of fish and plants, depending on various environmental factors.

Effect of a Quaternary Meteoroid Impact in Indo-China on the Surface Sedimentary Record

NASA Astrophysics Data System (ADS)

Carling, Paul; Songtham, Wickanet; Tada, Riuji; Tada, Toshihiro; Duangkrayon, Jaa

2017-04-01

Effects of meteoroid impacts on terrestrial geology primarily have been considered with respect of proximal effects near the impact location; such as cratering, fracturing and melt. However, other than the use of rare elements (iridium) as event markers and tektite chemistry for dating control, distal effects of impacts are less-well documented. Distal effects might include: fireball, air blast, heat, water vaporization, catastrophic flooding, earthquakes, ejecta fallout (tektites & dust), large quantities of N2O from shock heating of the atmosphere, release of CO2 and sulphur aerosols causing heating or cooling of atmosphere, IR radiation causing vegetation fires, smoke and pyrotoxins, and altered native rock geochemistry. Such processes may affect the distal surface geology, degrade vegetation cover and cause extirpation of flora and fauna. Quaternary sedimentary sections have been examined in northern and central Cambodia, in southern China and in north-east Thailand. These locality lie within the Australian strewn tektite field ̶ reliably dated to 0.77-0.78Ma BP ̶ just before the 0.80Ma BP Brunhes/Matayama reversal. The location of the primary impact crater (if any) is uncertain but a local major crater probably lies within central Laos or just offshore to the east. The described sections are considered distal from the main impact. Stratigraphic evidence indicates a temporal sequence of catastrophic stripping of alluvial-gravel surfaces followed by catastrophic redistribution of gravel (incorporating tektites), followed by deposition of atmospheric dust. Grain-size and grain-density trends, XRD, spherule distributions, luminescence profiles, tektite, and microtektite and shock quartz assay, are used to with the stratigraphic evidence to examine an hypothesis that the sections represent the distal effects of a meteorite. Additional insight is gained with respect to prior claims that large accumulations of woody debris in Thai Quaternary river terraces were due to blast and are burnt. Fossil evidence for the local extirpations of Quaternary mammals within the region might also be related to the impact event. Tektites occur at the same level as occupation horizons of Palaeolithic people such that the impact would have had direct effects on hominins. The stratigraphy includes: erosional antidunes, blast-induced debris flow incorporating tektites, catastrophically-broken laterite pavements and mud layers with reversed magnetism. Sedimentological evidence in favour of impact includes: the presence of delicate thin translucent-tektites that must be in situ from initial fallout as reworking would destroy them, graded spherule distributions, highly-stressed quartz grains and microtektites. Grain size data, including X-ray and CT-scanning analysis, can be used to support the impact hypothesis but alone these data are not conclusive. XRD data is inconclusive. On balance the stratigraphy and sedimentology support the notion that the sediments represent the distal effects of a meteorite in the region.

Detrital and early chemical remanent magnetization in redbeds and their rock magnetic signature: Zicapa Formation, southern Mexico

NASA Astrophysics Data System (ADS)

Sierra-Rojas, Maria Isabel; Molina-Garza, Roberto Stanley

2018-06-01

Poles from continental redbeds are a large fraction of the world's palaeomagnetic database. Nonetheless, the time of acquisition and origin of the remanent magnetization of redbeds has been long debated. We report palaeomagnetic data, rock magnetic data and microscope observations for Lower Cretaceous redbeds in southern Mexico. These data allow us to discriminate between the hysteresis properties of remanent magnetizations of detrital and chemical origin, and to establish the early origin of a chemical remanence. Red sandstones of the Zicapa Formation contain a multicomponent remanence revealed by thermal demagnetization, and consisting of three stable components with partially overlapping laboratory unblocking temperatures of <250 °C, ˜300 to ˜500 °C and >600 °C, (low, intermediate and high temperature, respectively). They are interpreted as a viscous remanence residing in detrital magnetite, a chemical remanence residing in authigenic hematite and a depositional remanence residing in detrital hematite, respectively. The low-temperature component is nearly parallel to the recent dipole field. The tilt-corrected overall site means of the intermediate (chemical) and high temperature (depositional) components are indistinguishable (Dec = 282.0°, Inc = 12.4°, k = 13.33, α95 = 10.1°, N = 17, for the intermediate temperature; and Dec = 272.5°, Inc = 16.5°, k = 14.04, α95 = 11, N = 14, for the high temperature). Elongation/inclination analysis suggests that depositional and chemical components require applying an f = factor of approximately 0.4. Both of these components define a magnetic polarity zonation, but the polarity of the chemical and detrital components may or may not be the same. The chemical remanence coincides, more often than not, with the polarity of the depositional remanence of the overlying (younger) strata, suggesting a delay in remanence acquisition of tens to a few hundred ka for the chemical component. Pigmentary and detrital haematite were recognized with microscopic observations. The particle size of haematite ranges from approximately 10 to 300 μm for detrital haematite (martite, specularite and laterite), and from ca. 0.2 to 1 μm for pigmentary haematite flakes. The IRM of these rocks can be modelled with components of low coercivity (H1/2 between 5 and 10 mT interpreted as detrital magnetite), and components of a wide coercivity range (prevailing H1/2 from ˜400 to 600 mT interpreted as haematite). Hysteresis ratios show a systematic correlation with demagnetization behaviour, with lower Hcr/Hc values and higher Mrs/Ms values for samples with a dominant chemical component, than form samples with a significant (>40 per cent) depositional component.

Groundwater Quality Assessment in the Upper East Region of Ghana

NASA Astrophysics Data System (ADS)

Apambire, W. B.

2001-05-01

In Ghana, West Africa, fluoride occurs as a natural pollutant in some groundwaters, while the presence of isolated high levels of nitrate and arsenic in groundwater is due to human activities such as poor sanitation, garbage disposal and mining practices. The challenge for Ghana is to ensure that groundwater quality and environmental adversities such as water level decline are not compromised by attempts to increase water quantity. Concentrations of groundwater fluoride in the study area range from 0.11 to 4.60 mg/L, with the highest concentrations found in the fluorine-enriched Bongo granitoids. Eighty-five out of 400 wells sampled have fluoride concentrations above the World Health Organization maximum guideline value of 1.5 mg/L and thus causes dental fluorosis in children drinking from the wells. The distribution of fluoride in groundwater is highly related to the distribution of dental fluorosis in the UER. Nitrate concentrations ranged from 0.03 to 211.00 mg/L and the mean value was 16.11 mg/L. Twenty-one samples had concentrations in excess of the guideline value of 45 mg/L. Consumption of water in excess of the guideline value, by infants, may cause an infantile disease known as methaemoglobinaemia. It is inferred that groundwaters with exceptionally high NO3 values have been contaminated principally through human activities such as farming and waste disposal. This is because wells with high nitrate concentrations are all located in and around towns and sizable villages. Also, there is good correlation between Cl and NO3 (r = +0.74), suggesting that both elements come from the same sources of pollution. Only two well waters had concentrations of iron in excess of the guideline value of 0.3 mg/L. These samples come from shallow hand-dug wells. The maximum concentration of iron in groundwaters is 3.5 mg/L. The recommended guideline limit for Al in drinking water is 0.2 mg/L; two wells had Al concentrations of 12.0 and 4.0 mg/L, respectively. Other high concentrations of Al are associated with shallow wells and ponds. There is a highly positive correlation (r = +1) between Fe and Al, suggesting that dissolution of weathered lateritic material (e.g., Fe oxides, gibbsite, etc.) is the common source for these elements. Manganese concentrations are generally within acceptable limits, except for 11 wells that have concentrations above the guideline limit of 0.1 mg/L. These anomalous concentrations may be associated with manganiferous deposits in the study area. A majority of the samples contain very low concentrations of the trace elements Zn, Pb, Cd, Cr, As and Se; however, the highest concentrations occur in areas where small-scale mining is practiced.

The cancrinite-syenite/carbonatite complex of Lueshe, Kivu/NE-Zaire: petrographic and geochemical studies and its economic significance

NASA Astrophysics Data System (ADS)

Maravic, H. v.; Morteani, G.; Roethe, G.

The Luesche cancrinite-syenite/carbonatite complex is located in NE-Zaire about 50 km SSW of Lake Edward. The alkaline rocks have intruded metamorphic rocks of Burundian age (1.100 m.y.). The country rocks are quartzites and mica schists bearing chlorite, garnet, Kyanite and staurolite, which indicates P-T conditions of some 4 kbar and 430-500°C, maximum 6 kbar and 620°C. The K/Ar age of the biotites from the carbonatite is found to be 516 m.y. The core of the alkaline complex is composed of cancrinite-syenites which vary from place to place with respect to the contents of garnet, amphibole, aegirine, sodalite and cancrinite. Significant variations of the pyrochlore content are also observed. The core is surrounded by fine grained calcitic carbonatite (alvikite) which often shows a banded texture and grades into coarse grained calcitic carbonatite (søvite). In the SE of the søvite ring there is a separate dolomitic carbonatite body (beforsite) while at the contacts between the alkaline rocks and the country rocks a wide range of low to high grade fenites enriched in Na or K occurs. Within the alkaline complex the highest niobium values are found associated with metasomatic rocks of the contact zones such as carbosyenites, pyroxentic rocks and fenites. The main niobium mineral is a Ca, Na-pyrochlore enriched in Ti and/or Sr. The geochemical distribution patterns of the major elements as well as of the trace elements, especially the REE, suggests that the carbonatites are of primary magmatic origin derived from mantle material which was affected by later remobilizations, most likely as a result of postmagmatic hydrothermal solutions. Regarding the cancrinite-syenites, there is no evidence for a comagmatic formation with the carbonatites. They are rather of subcrustal origin; formed in the course of various metasomatic processes where the alkalic carbonate melts or volatile carbonate phases interacted with the metamorphic country rocks to form rheomorphic syenites which subsequently intruded. From an economic point of view only the lateritic zone derived from weathering of the carbo-syenites, pyroxenitic rocks and fenites is considered as ore due to the concentration of pyrochlore in the course of weathering. Ore grades vary from 1 % to 7 % Nb 2O 5. The ore is composed of clay minerals, iron oxides and phosphates. The weathering profile may be up to 150 m deep, whereby a gradual change with depth from crandallitic ore to crandallitic-apatitic ore and to apatitic ore in the bottom section occurs. Ore reserves amount to some 8 million tons with an average of 2.5 % Nb 2O 5. By these figures Lueshe is one of the few high grade niobium deposits in the world.

Phanerozoic burial, uplift and denudation of the Equatorial Atlantic margin of South America

NASA Astrophysics Data System (ADS)

Japsen, Peter; Bonow, Johan M.; Green, Paul F.; dall'Asta, Massimo; Roig, Jean-Yves; Theveniaut, Hervé

2017-04-01

We have initiated a study aimed at understanding the history of burial, uplift and denudation of the South American Equatorial Atlantic Margin (SAEAM Uplift) including the Guiana Shield to provide a framework for investigating the hydrocarbon prospectivity of the offshore region. We report first results including observations from fieldwork at the northern and southern flank of the Guiana Shield. The study combines apatite fission-track analysis (AFTA) and vitrinite reflectance data from samples of outcrops and drillcores, sonic velocity data from drill holes and stratigraphic landscape analysis (mapping of peneplains) - all constrained by geological evidence, following the methods of Green et al. (2013). The study will thus combine the thermal history from AFTA data with the denudation history from stratigraphic landscape analysis to provide magnitudes and timing of vertical movements (Japsen et al. 2012, 2016). Along the Atlantic margin of Suriname and French Guiana, tilted and truncated Lower Cretaceous strata rest on Precambrian basement (Sapin et al. 2016). Our AFTA data show that the basement underwent Mesozoic exhumation prior to deposition of the Lower Cretaceous cover. Sub-horizontal peneplains define the landscape of the Guiana Shield at elevations up to 500 m a.s.l. As these sub-horizontal peneplains truncate the tilted, sub-Cretaceous surface along the Atlantic margin, these peneplains were therefore formed and uplifted in post-Cretaceous time. This interpretation is in good agreement with our AFTA data that define Paleogene exhumation along the margin and with the results of Theveniaut and Freyssinet (2002) who used palaeomagnetic data to conclude that bauxitic surfaces across basement at up to 400 m a.s.l. on the Guiana Shield formed during the Palaeogene. Integration of the results from AFTA with stratigraphic landscape analysis (currently in progress) and geological evidence will provide a robust reconstruction of the tectonic development of the onshore margin. References Green, Lidmar-Bergström, Japsen, Bonow & Chalmers 2013: Stratigraphic landscape analysis, thermochronology and the episodic development of elevated passive continental margins. GEUS Bulletin. Japsen, Green, Bonow & Erlström 2016: Episodic burial and exhumation of the southern Baltic Shield: Epeirogenic uplifts during and after break-up of Pangea. Gondwana Research. Japsen, Bonow, Green, Cobbold, Chiossi et al. 2012: Episodic burial and exhumation history of NE Brazil after opening of the South Atlantic. GSA Bulletin. Sapin, Davaux, dall'Asta et al. 2016: Post-rift subsidence of the French Guiana hyper-oblique margin: from rift-inherited subsidence to Amazon deposition effect. Geol. Soc. Spec. Publ. Theveniaut & Freyssinet 2002: Timing of lateritization on the Guiana Shield: synthesis of paleomagnetic results from French Guiana and Suriname. 3 x Palaeo.

Predicting local Soil- and Land-units with Random Forest in the Senegalese Sahel

NASA Astrophysics Data System (ADS)

Grau, Tobias; Brandt, Martin; Samimi, Cyrus

2013-04-01

MODIS (MCD12Q1) or Globcover are often the only available global land-cover products, however ground-truthing in the Sahel of Senegal has shown that most classes do have any agreement with actual land-cover making those products unusable in any local application. We suggest a methodology, which models local Wolof land- and soil-types in an area in the Senegalese Ferlo around Linguère at different scales. In a first step, interviews with the local population were conducted to ascertain the local denotation of soil units, as well as their agricultural use and woody vegetation mainly growing on them. "Ndjor" are soft sand soils with mainly Combretum glutinosum trees. They are suitable for groundnuts and beans while millet is grown on hard sand soils ("Bardjen") dominated by Balanites aegyptiaca and Acacia tortilis. "Xur" are clayey depressions with a high diversity of tree species. Lateritic pasture sites with dense woody vegetation (mostly Pterocarpus lucens and Guiera senegalensis) have never been used for cropping and are called "All". In a second step, vegetation and soil parameters of 85 plots (~1 ha) were surveyed in the field. 28 different soil parameters are clustered into 4 classes using the WARD algorithm. Here, 81% agree with the local classification. Then, an ordination (NMDS) with 2 dimensions and a stress-value of 9.13% was calculated using the 28 soil parameters. It shows several significant relationships between the soil classes and the fitted environmental parameters which are derived from field data, a digital elevation model, Landsat and RapidEye imagery as well as TRMM rainfall data. Landsat's band 5 reflectance values (1.55 - 1.75 µm) of mean dry season image (2000-2010) has a R² of 0.42 and is the most important of 9 significant variables (5%-level). A random forest classifier is then used to extrapolate the 4 classes to the whole study area based on the 9 significant environmental parameters. At a resolution of 30 m the OBB (out-of-bag) error rate is 6.55%. At this scale, even small depressions and local discrepancies at field-level can be identified. Scaling to 250, 500 and 1000 m still gives a reliable overview of prevalent soil-units in the region. By relating soil to vegetation parameters we prove, that these maps indicate the potential dominant woody vegetation. Our example demonstrates, that solely the use of native Wolof land-types, which are gathered by interviews, can be used to get a proper scientific classification of (a) the agricultural suitability and (b) the dominant woody vegetation in an area of the Senegalese Sahel region.

Mineralogical and geochemical characteristics of the Noamundi-Koira basin iron ore deposits (India)

NASA Astrophysics Data System (ADS)

Mirza, Azimuddin; Alvi, Shabbar Habib; Ilbeyli, Nurdane

2015-04-01

India is one of the richest sources of iron ore deposits in the world; and one of them is located in the Noamundi-Koira basin, Singhbhum-Orissa craton. The geological comparative studies of banded iron formation (BIF) and associated iron ores of Noamundi-Koira iron ore deposits, belonging to the iron ore group in eastern India, focus on the study of mineralogy and major elemental compositions along with the geological evaluation of different iron ores. The basement of the Singhbhum-Orissa craton is metasedimentary rocks which can be traced in a broadly elliptical pattern of granitoids, surrounded by metasediments and metavolcanics of Greenstone Belt association. The Singhbhum granitoid is intrusive into these old rocks and to younger, mid Archaean metasediments, including iron formations, schists and metaquartzites and siliciclastics of the Precambrian Iron Ore Group (Saha et al., 1994; Sharma, 1994). The iron ore of Noamundi-Koira can be divided into seven categories (Van Schalkwyk and Beukes 1986). They are massive, hard laminated, soft laminated, martite-goethite, powdery blue dust and lateritic ore. Although it is more or less accepted that the parent rock of iron ore is banded hematite jasper (BHJ), the presence of disseminated martite in BHJ suggests that the magnetite of protore was converted to martite. In the study area, possible genesis of high-grade hematite ore could have occurred in two steps. In the first stage, shallow, meteoric fluids affect primary, unaltered BIF by simultaneously oxidizing magnetite to martite and replacing quartz with hydrous iron oxides. In the second stage of supergene processes, deep burial upgrades the hydrous iron oxides to microplaty hematite. Removal of silica from BIF and successive precipitation of iron resulted in the formation of martite- goethite ore. Soft laminated ores were formed where precipitation of iron was partial or absent. The leached out space remains with time and the interstitial space is generally filled with kaolinite and gibbsite, which make it low grade. Massive iron ores are devoid of any lamination and usually associated with BHJ and lower shale. The thickness of the massive ore layer varies with the location. The massive iron ore grades in to well-developed bedded BHJ in depth. Blue dust occurs in association with BHJ as pockets and layers. Although blue dust and friable ore are both powdery ores, and subjected to variable degree of deformation, leading to the formation of folding, faulting and joints of complex nature produce favourable channels. Percolating water play an important role in the formation of blue dust and the subterranean solution offers the necessary acidic environment for leaching of quartz from the BHJ. The dissolution of silica and other alkalis are responsible for the formation of blue dust. The friable and powdery ore on the other hand are formed by soft laminated ore. As it is formed from the soft laminated ore, its alumina content remains high similar to soft laminated ore compaired to blue dust. Mineralogy study suggests that magnetite was the principal iron oxide mineral, now a relict phase whose depositional history is preserved in BHJ, where it remains in the form of martite. The platy hematite is mainly the product of martite. The different types of iron ores are intricately related with the BHJ. Hard laminated ores, martite-goethite ore and soft laminated ore are resultant of desilicification process through the action of hydrothermal fluids. Geochemistry of banded iron-formations of the Noamundi-Koira iron ore deposits shows that they are detritus-free chemical precipitates. The mineralogical and geochemical data suggest that the hard laminated, massive, soft laminated ores and blue dust had a genetic lineage from BIF's aided with certain input from hydrothermal activity. The comparative study of major elemental composition of the basin samples and while plotting a binary diagram, it shows a relation between major oxides against iron oxides, in which iron oxides is taken as a reference oxide (Mirza, 2011). On the other hand, by plotting a binary diagram between chemical index of alteration (CIA) and other oxides while taking the samples of lower, middle and upper shales. It reflects an immobility and mobility of ions during partial and complete weathering processes (Mirza, 2011). Geochemical data indicate that BIF are in general detritus free chemical precipitates. Fe2O3 content of BHJ are varies in between 36.6% to 65.04%. In hard laminated ore, Fe2O3 content varies from 93.8% to 96.38%, Soft laminated ore varies from 83.64% to 89.5% and laterite ore varies from 53.5% to 79.11%. Fe2O3 content in Martite- Goethite ore varies from 86.38% to 89.42% and blue dust having 90.74% to 95.86% and all other oxides like SiO2, Al2O3, CaO, MgO, K2O, Na2O are decreases. Major part of the iron could have been added to the bottom sea water by hydrothermal solutions derived from hydrothermally active anoxic marine environments. The presence of intacalated tuffaceous shales pointing towards the genesis of iron, which could have leached from sea floor by volcanogenic process. Iron and silica of BIF were provided by the hydrothermal solutions emplaced at the vent sites situated at the Archean-Mid Oceanic Ridges. References: Mirza A (2011). Major element geochemistry of iron ore deposits in Noamundi-Koira basin of Singhbhum-Orissa craton (India). MSc thesis, Aligarh Muslim University, India. Saha AK (1994). Crustal evolution of Singhbhum, North Orissa, Eastern India; Geol. Soc. India Memoir 27 341. Sharma M, Basu AR and Ray SL (1994). Sm-Nd isotopic and geochemical study of the Archaean tonalite-amphibolite association from the eastern Indian craton. Contrib. Mineral Petrol. 117:45-55. Van Schalkwyk J and Beukes N J (1986). The Sishen iron ore deposit, Griqualand West; In: Mineral deposits of Southern Africa (eds) Annhaeusser C R and Maske S S, Geological Society of South Africa, Johannesburg, 931-956.

Volcaniclastic stratigraphy of Gede volcano in West Java

NASA Astrophysics Data System (ADS)

Belousov, A.; Belousova, M.; Zaennudin, A.; Prambada, O.

2012-12-01

Gede volcano (2958 m a.s.l.) and the adjacent Pangrango volcano (3019 m a.s.l.) form large (base diameter 35 km) volcanic massif 60 km south of Jakarta. While Pangrango has no recorded eruptions, Gede is one of the most active volcanoes in Indonesia: eruptions were reported 26 times starting from 1747 (Petroeschevsky 1943; van Bemmelen 1949). Historic eruptions were mildly explosive (Vulcanian) with at least one lava flow. Modern activity of the volcano includes persistent solfataric activity in the summit crater and periodic seismic swarms - in 1990, 1991, 1992, 1995, 1996, 1997, 2000, 2010, and 2012 (CVGHM). Lands around the Gede-Pangrango massif are densely populated with villages up to 1500-2000 m a.s.l. Higher, the volcano is covered by rain forest of the Gede-Pangrango Natural Park, which is visited every day by numerous tourists who camp in the summit area. We report the results of the detailed reinvestigation of volcaniclastic stratigraphy of Gede volcano. This work has allowed us to obtain 24 new radiocarbon dates for the area. As a result the timing and character of activity of Gede in Holocene has been revealed. The edifice of Gede volcano consists of main stratocone (Gumuruh) with 1.8 km-wide summit caldera; intra-caldera lava cone (Gede proper) with a 900 m wide summit crater, having 2 breaches toward N-NE; and intra-crater infill (lava dome/flow capped with 3 small craters surrounded by pyroclastic aprons). The Gumuruh edifice, composed mostly of lava flows, comprises more than 90% of the total volume of the volcano. Deep weathering of rocks and thick (2-4 m) red laterite soil covering Gumuruh indicates its very old age. Attempts to get 14C dates in 4 different locations of Gumuruh (including a large debris avalanche deposit on its SE foot) provided ages older than 45,000 years - beyond the limit for 14C dating. Outside the summit caldera, notable volumes of fresh, 14C datable volcaniclastic deposits were found only in the NNE sector of the volcano where they form a fan below the breached summit crater. The fan is composed of pyroclastic flows (PFs) and lahars of Holocene age that were deposited in 4 major stages: ~ 10 000 BP - voluminous PF of black scoria; ~ 4000 BP - two PFs of mingled grey/black scoria; ~ 1200 BP - multiple voluminous PFs strongly enriched by accidental material; ~ 1000 BP - a small scale debris avalanche (breaching of the crater wall) followed by small scale PFs of black scoria. The intra-crater lava dome/flow was erupted in 1840 (Petroeschevsky, 1943). Three small craters on the top of the lava dome were formed by multiple post-1840 small-scale phreatomagmatic eruptions. Ejected pyroclasts are lithic hydrothermally altered material containing a few breadcrust bombs. The Holocene eruptive history of Gede indicates that the volcano can produce moderately strong (VEI 3-4) explosive eruptions and send PFs and lahars onto the NE foot of the volcano.

21st century hydrological modeling for optimizing traditional soil and water conservation practices

NASA Astrophysics Data System (ADS)

Wildemeersch, Jasmien; Garba, Maman; Sabiou, Mahaman; Al-Barri, Bashar; Cornelis, Wim

2017-04-01

In order to increase dryland productivity, soil and water conservation practices have received renewed attention, leading to their massive implementation in marginal drylands. However, versatile tools to evaluate their efficiency under a wide range of conditions are often lacking. This study focuses on semi-arid Niger, where as a result of growing population pressure and severe soil erosion, farmers increasingly rely on degraded lands for millet production. The adverse rainfall distribution and imbalanced rainfall partitioning over the rootzone of these degraded lands calls for sustainable land management strategies that are water resource efficient. We therefore evaluated the soil-water balance of promising Nigerien Water and Soil Conservation (WSC) techniques (i.e., zaï pits, demi-lune microcatchments and scarification with standing crop residue) and their impact on millet yield by means of an in-situ field experiment on degraded laterite soil classified as Plinthosol with a 1% slope. We also applied a fully coupled 3D surface-subsurface hydrological model based on the Richards' and the Saint Venant equations to further improve promising WSC techniques. All WSC practices received the same amount of fertilizer and were compared to two control practices, one with and one without fertilizer. Soil-water content was recorded with a neutron probe till 105 cm depth and runoff by means of a cemented gutter directing runoff water with a multi-pipe divisor into a collector drum. WSC techniques proved to significantly reduce runoff with overall runoff coefficients being reduced from 25% (control practice) to 5-10%. Consequently, significantly more water was stored inside the catchments of the zaï pits and demi-lunes. With the scarification treatment, no considerable differences in soil-water storage were found with the control. On the other hand, WSC practices had little impact on soil evaporation, which was only 12% of rainfall by the self-mulching soil. Crop transpiration increased with WSC and highest millet yields were found with zaï pits (4 to 5 times higher than under the fertilized control). Although rainwater was better partitioned in case of demi-lune microcatchments resulting in highest amounts of water stored in the soil, yield was only 40-60% of that with zaï pits. This was due to a higher plant density within each demi-lune microcatchment in an attempt to attain similar plant densities at field scale across the treatments. An optimized design for demi-lune microcatchments, in which the number of catchments per surface area is increased while reducing plant density per catchment, is therefore suggested. This was demonstrated using the fully coupled surface-subsurface process-based model that enabled to simulate at field scale overland and soil-water flow in 3D under various WSC designs. The model would also allow to evaluate the effect of WSC practices at catchment scale.

Bauxite to eclogite: Evidence for late Permian supracontinental subduction at the Red River shear zone, northern Vietnam

NASA Astrophysics Data System (ADS)

Nakano, Nobuhiko; Osanai, Yasuhito; Nam, Nguyen Van; Tri, Tran Van

2018-03-01

We have investigated the geological processes recorded in aluminous granulites from the Red River shear zone in northern Vietnam using mineral and whole-rock chemistries, fluid inclusions, metamorphic pressure-temperature paths, and geochronology. The granulites are extremely rich in Al2O3 (36.3-50.9 wt%), TiO2, and total Fe2O3, and poor in SiO2 (7.9-24.1 wt%), MgO, CaO, Na2O, and K2O. The granulites are enriched in high-field-strength elements and rare earth elements, and severely depleted in large-ion lithophile elements. These features strongly suggest the protolith was lateritic bauxite. Moreover, the other elemental concentrations and the Zr/Ti ratios point to basaltic rock as the precursor of the bauxite. Some of the aluminous granulites contain high-pressure mineral inclusions of kyanite, staurolite, siderite, and rutile, none of which are observed in the matrix. Abundant primary carbonic fluid inclusions are observed in garnet, corundum, and staurolite, but are rare in quartz and zircon. The average densities of fluid inclusions in garnet, corundum, staurolite, quartz, and zircon are 1.00 ± 0.06, 1.07 ± 0.04, 1.09 ± 0.03, 0.29 ± 0.07, and 1.15 ± 0.05 g/cm3, respectively. The mineral features not only in the matrix and but also in garnet from all rock types, isochemical phase diagrams obtained for each bulk rock composition, and Zr-in-rutile thermometry indicate an early eclogite-facies metamorphism ( 2.5 GPa at 650 °C) and a subsequent nearly isothermal decompression. Zircons yield a wide range of U-Pb ages from 265 to 36 Ma, whereas the dark luminescent cores of the zircons, which contain high-density CO2 inclusions, yield a concordia age of 257 ± 8 Ma. These observations suggest that the dark luminescent zircon cores were formed at the same time as the garnet, corundum, and staurolite that contain high-density CO2 fluid inclusions. Based on the carbonic fluid inclusion isochore and the densities as well as calculated phase diagram, the concordia age can be regarded as recording a prograde stage of metamorphism under conditions lower than 600 °C and 0.7 GPa. Our new data provide the following geological and tectonic constraints: 1) the eruption of basalt occurred before the Permian, possibly related to subduction of the Paleo-Tethys Plate beneath the Indochina craton near the paleo-equator in the Devonian-Carboniferous; 2) strong weathering transformed the basalt to bauxite before the late Permian; 3) the uppermost continental crust, including the bauxites, was subducted in the late Permian due to the collision of the Indochina and South China cratons, leading to eclogite-facies metamorphism; 4) the rocks were then exhumed; and 5) shearing-related thermal events took place until the Paleogene.

Ediacaran stromatolites and intertidal phosphorite of the Salitre Formation, Brazil: Phosphogenesis during the Neoproterozoic Oxygenation Event

NASA Astrophysics Data System (ADS)

Caird, R. A.; Pufahl, P. K.; Hiatt, E. E.; Abram, M. B.; Rocha, A. J. D.; Kyser, T. K.

2017-04-01

The Ediacaran Nova America and Gabriel members of the Salitre Formation are composed of limestone and economic phosphorite that accumulated on an unrimmed epeiric ramp along the margins of the Irecê Basin, Brazil. Deposition occurred during a marine transgression punctuated by higher-order fluctuations in relative sea-level that produced m-scale, shallowing-upward peritidal cycles. Cycles consist of six lithofacies rich in microbial sedimentary structures including subtidal, cross-stratified grainstones and hemispheroidal columnar stromatolite reefs overlain by intertidal flat sediments indicative of decreasing accommodation. Phosphorite is restricted to the paleocoast where digitate stromatolite biostromes colonized tidal flats. Phosphorite accumulation is interpreted to have been associated with biostromes because photosynthetic oxygen production created a redox gradient beneath the seafloor that phosphogenic chemosynthetic bacteria exploited. The concentration of francolite or sedimentary apatite in microbial laminae suggests these bacteria actively stored, released, and concentrated phosphate to promote in situ precipitation. The sealing effect of interbedded, fine-grained tidal deposits was also critical for maintaining the high levels of pore water phosphate required. The absence of francolite in subtidal columnar stromatolite reefs implies phosphogenesis was prevented in deeper, more energetic environments because wave pumping of oxygenated seawater through reefs surrounded by constantly moving grainy sediment promoted the recycling of P directly back to the water column. The Salitre Formation has a complex paragenesis, including hydrothermal alteration that produced Mississippi Valley-type Pb-Zn mineralization. δ18O values of Nova America member dolomites range from - 10.2‰ to - 0.5‰ (mean = - 3.9‰) and δ13C ranges from - 9.2‰ to + 10.0‰ (mean = + 2.8‰). Samples contain varying proportions of low-Mg calcite and saddle dolomite. δ18O values of hydrothermal veins range from - 4.7‰ to - 3.0‰ (mean = - 4.2‰) reflecting equilibration with temperatures > 80 °C. δ13C values are between - 7.0‰ and + 5.6‰ (mean = - 1.8‰,). Late lateritic weathering produced calcretes with δ18O values between - 3.3‰ and - 1.3‰, and δ13C values from - 9.2‰ to - 8.0‰ (mean values are - 1.8‰ and - 8.7‰, respectively). Petrographic analysis, generally low δ18O, and high δ13C values suggest hydrothermal dolomitization and remobilization of P led to secondary phosphate mineralization of intertidal stromatolite biostromes to produce economic phosphorite. Collectively, these results suggest that the benthic P-cycle in the Neoproterozoic was more complex than previously surmised and emphasize the multifaceted significance of microbial, paleoenvironmental, and diagenetic processes that allowed phosphorite to accumulate on the São Franciscan craton. Such information further elucidates attributes of the onset of Earth's second major phosphogenic episode, which is roughly coincident with the Neoproterozoic Oxygenation Event (NOE) and the evolution of multicellular animals.

Origin of enormous trace metal enrichments in weathering mantles of Jurassic carbonates: evidence from Sr, Nd and Pb isotopes

NASA Astrophysics Data System (ADS)

Hissler, C.; Stille, P.; Juilleret, J.; Iffly, J.; Perrone, T.; Morvan, G.

2013-12-01

Weathering mantels are widespread worldwide and include lateritic, sandy and kaolinite-rich saprolites and residuals of partially dissolved carbonate rocks. These old regolith systems have a complex history of formation and may present a polycyclic evolution due to successive geological and pedogenetic processes that affected the profile. Until now, only few studies highlighted the unusual content of associated trace elements in this type of weathering mantle. For instance, these enrichments can represent about five times the content of the underlying Bajocian to Oxfordian limestone/marl complexes, which have been relatively poorly studied compared to weathering mantle developed on magmatic bedrocks. Up to now, neither soil, nor saprolite formation has to our knowledge been geochemically elucidated. Therefore, the aim of this study was to examine more closely the soil forming dynamics and the relationship of the chemical soil composition to potential sources (saprolite, Bajocian silty marls and limestones, atmospheric particles deposition...). Of special interest has also been the origin of trace metals and the processes causing their enrichments. Especially Rare Earth Element (REE) distribution patterns and Sr, Nd and Pb isotope ratios are particularly well suited to identify trace element migration, to recognize origin and mixing processes and, in addition, to decipher possible anthropogenic and/or "natural" atmosphere-derived contributions to the soil. Moreover, leaching experiments shall help to identify mobile phases in the soil system. This may inform on the stability of trace elements and especially on their behaviour in these Fe-enriched carbonate systems. Trace metal migration and enrichments were studied on a cambisol developing on an underlying Jurassic limestone. The base is strongly enriched among others in rare earth elements (ΣREE: 2640ppm) or redox-sensitive elements such as Fe (44 wt.%), V (920ppm), Cr (700ppm), Zn (550ppm), As (260ppm), Co (45ppm) and Cd (2.4ppm). The underlying limestone and marl show, compared to average world carbonates, enrichments in the same elements and trace element distribution patterns similar to the soil suggesting their close genetic relationship. Pb, Sr and Nd isotope data allow to identify three principal components in the soil: a silicate-rich phase at close to the surface, a strongly trace metal enriched component at the bottom of the soil profile and an anthropogenic, atmosphere- derived component detected in the soil leachates. The isotopic mixing curves defined by the soil samples point to the close genetic connection between upper and lowermost soil horizons. The Nd isotopic composition of the leachates of all soil horizons are in contrast to the untreated soil and residual soil samples very homogeneous suggesting that the leachable phases of the upper and lower soil horizons are genetically connected. The downward migration of the trace metals is stopped at this soil level due to the presence of important secondary calcite precipitations, smectite and Fe-oxide accumulations. Mass balance calculations indicate that the enrichment process goes along with a volume increase relative to the bottom soil horizons.

Revised Geochronology and Magnetostratigraphy of Northwest Iceland

NASA Astrophysics Data System (ADS)

Riishuus, M. S.; Duncan, R. A.; Kristjansson, L.

2013-12-01

The lava pile of the NW peninsula of Iceland is largely composed of tholeiites, with less abundant olivine basalts and plagioclase porphyritic basalts, with a modest regional dip toward the southeast. The peninsula attracted the attention of scientists already in the eighteenth century, especially its occurrences of fossiliferous sediment layers of variable volcaniclastic character containing lignite. Fieldwork in a large stratigraphic mapping project was initiated in 1975 (McDougall et al., 1984). This project involved sampling of 1261 lava flows for paleomagnetic studies of ~50 correlated profiles in the western and eastern coastal areas of the peninsula, and K-Ar dating of >70 lava flows in the profiles. On the western side the average rate of buildup of the lava pile was found to be ~1800 m/Myr, corresponding to a mean time interval between successive lava flows of about 5000 yrs, and contrasting with a much lower rate of ~700 m/Myr for the younger eastern sequence. Only a few radiometric ages have been obtained from the Northwest peninsula after 1984 without adding much to the previous knowledge of the buildup of the peninsula. The effort by McDougall et al. (1984) has however been followed by three smaller but sizable projects on the stratigraphy and paleomagnetism of the peninsula. In one of these studies, altogether 307 lavas were sampled in 12 profiles in the tributary fjords south of Ísafjardardjúp. Using paleomagnetic polarities, lava petrography, and the ~12 Ma sediment horizon, a 2.6 km composite section was correlated with a central 2.8 km segment of the 4.1 km thick western section of McDougall et al. (1984). Here we present >50 new Ar-Ar ages on basaltic lava flows from magnetostratigraphic profiles across the peninsula. The results show that the preserved lavas below the oldest sediment horizon were erupted between ~17 and ~16 Ma at a low growth rate for the lava pile of 350m/Myr. The onset of volcanism above the unconformity occurred by 14.5-15.0 Ma - and at a significantly higher growth rate. This suggests that the period of volcanic quiescence, during which the lignite-bearing laterites were deposited, was long-lived (1-1.5 Myr). Our results also reveal significant variations in growth rates SW-NE along strike of the lava pile, presumably reflecting differences in the volcanic productivity along the rift zone, as well as higher resolution of temporal growth rate variations from 17 to 8 Ma (~350 m/Myr @ 17-15 Ma, ~2200m/Myr @ 14.5-13.8 Ma, ~700m/Myr @ 13.8-11.6 Ma, ~1500m/Myr @ 11.6-10.6 Ma, ~800m/Myr @ 10.5-8 Ma) than hitherto thought. At several stratigraphic levels the new absolute ages are significantly older than the recalculated age data from earlier studies. This requires reassessment of the correlation of the observed polarity patterns with the Geomagnetic Polarity Time Scale. McDougall, I., Kristjansson, L. and Saemundsson, K., 1984. Magnetostratigraphy and geochronology of Northwest Iceland. Journal of Geophysical Research 89, 7029-7060.

Ground-water geology of Kordofan Province, Sudan

USGS Publications Warehouse

Rodis, Harry G.; Hassan, Abdulla; Wahadan, Lutfi

1968-01-01

For much of Kordofan Province, surface-water supplies collected and stored in hafirs, fulas, and tebeldi trees are almost completely appropriated for present needs, and water from wells must serve as the base for future economic and cultural development. This report describes the results of a reconnaissance hydrogeologic investigation of the Province and the nature and distribution of the ground-water resources with respect to their availability for development. Kordofan Province, in central Sudan, lies within the White Nile-Nile River drainage basin. The land surface is largely a plain of low relief; jebels (hills) occur sporadically, and sandy soils are common in most areas except in the south where clayey soils predominate. Seasonal rainfall, ranging from less than 100 millimeters in the north to about 800 millimeters in the south, occurs almost entirely during the summer months, but little runoff ever reaches the Nile or White Nile Rivers. The rocks beneath the surficial depsits (Pleistocene to Recent) in the Province comprise the basement complex (Precambrian), Nawa Series (upper Paleozoic), Nubian Series (Mesozoic), laterite (lower to middle Tertiary), and the Umm Ruwaba Series (Pliocene to Pleistocene). Perennial ground-water supplies in the Province are found chiefly in five hydrologic units, each having distinct geologic or hydrologic characteristics. These units occur in Nubian or Umm Ruwaba strata or both, and the sandstone and conglomerate beds form the :principal aquifers. The water is generally under slight artesian head, and the upper surface of the zone of saturation ranges from about 50 meters to 160 meters below land surface. The surficial deposits and basement rocks are generally poor sources of ground water in most of the Province. Supplies from such sources are commonly temporary and may dissipate entirely during the dry season. Locally, however, perennial supplies are obtained from the surficial deposits and from the basement rocks. Generally, water from Nubian aquifers is satisfactory for most uses and is of better quality than that obtained from Umm Ruwaba aquifers. The relatively high mineralization of water from the Umm Ruwaba, especially in the eastern part of the Province, makes the water unsuitable for many municipal ad industrial uses. The water is generally usable, however, for domestic and livestock purposes. Some 175 drilled wells located at 75 water yards yield an average, of about 1,000 imperial gallons .per hour per well from Nubian or Umm Ruwaba. aquifers. Generally the water yards provide sufficient water for minimum domestic and livestock requirements throughout the year. Commonly, however, the water yards are widely separated and, hence, not always properly spaced for good range management or for serving the needs of the dispersed rural population. In 1962, withdrawals from Nubian and Umm Ruwaba aquifers in the Province were approximately 600 million gallons annually. This rate of draft: could probably be continued almost indefinitely without significant depletion of the water supply. Nubian and Umm Ruwaba aquifers in the southwestern part of Kordofan offer excellent potential for future development. Nubian aquifers in northern Kordofan need extensive exploration by test drilling before their economic potential can be properly evaluated.

Timing, tempo and paleoenvironmental implications of Deccan volcanism relative to the KTB extinction, what we can learn from the red bole record?

NASA Astrophysics Data System (ADS)

Adatte, Thierry; Sordet, Valentin; Keller, Gerta; Schoene, Blair; Samperton, Kyle; Khadri, Syed

2016-04-01

Deccan Traps erupted in three main phases with 6% total Deccan volume in phase-1 (C30n), 80% in phase-2 (C29r) and 14% in phase-3 (C29n). Recent studies indicate that the bulk (80%) of Deccan trap eruptions (phase-2) occurred over a relatively short time interval in magnetic polarity C29r. U-Pb zircon geochronology shows that the main phase-2 began 250 ky before the Cretaceous-Tertiary (KT) mass extinction and continued into the early Danian suggesting a cause-and-effect relationship. In India a strong floral response is observed as a direct consequence of volcanic phase-2. Shortly after the onset of Deccan phase-2, the floral association dominated by gymnosperms and angiosperms was decimated as indicated by a sharp decrease in pollen and spores coupled with the appearance of fungi, which mark increasing stress conditions as a direct result of volcanic activity. The inter-trappean sediments deposited in phase-2 are characterized by the highest alteration CIA index values suggesting increased acid rains due to SO2 emissions. In addition, a sharp decrease in pollen and spores coupled with the appearance of fungi mark increasing stress conditions, which are likely a direct result of volcanic activity. Bulk organic geochemistry points to a strong degradation of the indigenous organic matter, suggesting that the biomass was oxidized in acidic conditions triggered by intense volcanic activity. Closer to the eruption center, the lava flows are generally separated by red weathered horizons known as red boles that mark quiescent periods between basalt flows. Red boles have increasingly attracted the attention of researchers to understand the climatic and paleoenvironmental impact of Continental Flood Basalts (CFB). Recent advances in U-Pb dating of Deccan lava flows, studies of weathering patterns and paleoclimatic information gained from multiproxy analyses of red bole beds (e.g., lithology, mineralogy, geochemistry) yield crucial evidence of environmental changes triggered by volcanic activity. Red boles consist mainly of red silty clays characterized by concentrations of immobile elements such as Al and Fe3+ ions that are typical of paleo-laterites which probably developed during the short periods of weathering between eruptions. At least 30 thick red bole layers are present in C29r below the KT boundary between lava flows of phase-2 that erupted over a time span of about 250 ky. The short duration exposures of these red boles are reflected in the mineralogical and geochemical data that indicate rapid weathering (high CIA) linked to increasing acid rains. ∂D and ∂18O measured on smectite clays from the red boles approximate the meteoric water composition that prevailed during Deccan eruptions. Preliminary isotopic data from red boles deposited during the main phase-2 suggest significant and rapid changes in rainfall intensity and/or altitude linked to the accumulation of a 3100m thick basalt pile that erupted over a short period of time.

Airborne Gravity Gradiometry Resolves a Full Range of Gravity Frequencies

NASA Astrophysics Data System (ADS)

Mataragio, J.; Brewster, J.; Mims, J.

2007-12-01

Airborne Full Tensor Gradiometry (Air\\-FTGR) was flown at high altitude coincident with Airborne Gravity (AG) flown in 2003 in West Arnhem Land, Australia. A preliminary analysis of two data sets indicates that the Air\\-FTGR system has the capability of resolving intermediate to long wavelengths features that may be associated with relatively deeper geological structures. A comparison of frequency filtered slices and power spectral density (PSD) for both data sets using the short (> 5 km), intermediate (10 km) and long (20 km) wavelengths reveals that high altitude Air\\-FTGR data show greater response in high frequency anomalies than a conventional Airborne Gravity and matches well with the AG even at the longest wavelengths anomalies. The effect of line spacing and target resolution was examined between the two data sets. Reprocessed gradient and AG data at 2, 4 and 6 km line spacing suggest that Air\\-FTGR could be effectively flown at a comparatively wider line spacing to resolve similar targets the AG would resolve with tighter line spacing. Introduction Airborne Full Tensor Gradiometry (Air\\-FTGR) data have been available to the mining industry since 2002 and their use for geologic applications is well established. However, Air\\-FTGR data has been mostly considered and used in mapping and delineation of near surface geological targets. This is due to the fact that gravity gradiometer measurements are well suited to capture the high frequency signal associated with near\\-surface targets ( Li, 2001). This is possible because the gradiometer signal strength falls off with the cube of the distance to the target. Nonetheless, in recent years there has been an increasing demand from the mining, oil, and gas industry in utilizing Full Tensor Gravity Gradiometer as a mapping tool for both regional and prospect level surveys. Air\\-FTGR as a Regional Mapping Tool Several, relatively low altitude surveys have been successfully flown in Brazil, Canada and Australia mostly targeting large, regional\\- scale crustal structures as well as regional mapping of both lithology and regolith. Air\\-FTGR mapping is especially effective in areas of thick lateritic and/or clay cover where other geophysical methods such as airborne magnetics or electromagnetics become less effective. For instance, an Air\\-FTGR survey was successfully flown in Brazil in the Province of Minas Gerais, where several crustal\\-scale structures associated with iron oxide mineralization were identified ( Mataragio et. al., 2006). In addition, in 2006 Air\\-FTGR had good success in the regional mapping of structures associated with Iron Oxide Copper Gold (IOCG) and uranium mineralization in the Wernecke Mountains in the Yukon, and Northwest Territories, Canada. On the basis of these successful surveys, Bell Geospace has initiated a number of high altitude test surveys aiming at evaluating the performance of the Air\\-FTGR system in capturing low frequency signal that may be associated with regional\\-scale, deeper structures. One of the test surveys was conducted in December of 2006 in Australia, where the performance of Air\\-FTGR and the conventional Airborne Gravity were evaluated. Airborne gravity is currently considered well suited for capturing low frequency signal.

The influence of vegetation cover and soil physical properties on deflagration of shallow landslides - Nova Friburgo, RJ / Brazil

NASA Astrophysics Data System (ADS)

de Oliveira Marques, Maria Clara; Silva, Roberta; Fraga, Joana; Luiza Coelho Netto, Ana; Mululo Sato, Anderson

2017-04-01

In 2011, the mountainous region of the State of Rio de Janeiro (Brazil) suffered enormous social and economic losses due to thousands of landslides caused by an extreme rainfall event. The mapping of the scars of these landslides in an area of 421 km2 in the municipality of Nova Friburgo, RJ - Brazil resulted in a total of 3622, and 89% of these scars were located in areas covered by grasses and forests. Despite the unexpected result (64% of scars in forest areas), field evidence has shown that most of the forest fragments in the municipality are in the initial stages of succession and in different states of degradation, evidencing the need for a better understanding of the role of these forests in the detonation and propagation of landslides. Two slope forest areas with different ages (20 and 50 years) were evaluated in relation to the vegetative aspects that influence the stability of the slopes in each area. Hydrological monitoring, including precipitation, interception by manual and automatic method, soil moisture and subsurface flows were performed in two different areas: forest and grass. Soil moisture was monitored by granular matrix sensors and flows by collecting troughs in trenches at depths of 0 cm, 20 cm, 50 cm, 100 cm, 150 cm and 220 cm, which were also analyzed for biomass and length of thick roots (> 2 mm diameter) and thin roots (< 2 mm diameter) and for the soil physical properties (particle size, aggregate stability, porosity and hydraulic conductivity in situ). In the grass area, the lower soil structure in relation to the forest areas makes it difficult to transmit the water through the soil matrix. During the monitoring period, that area preserved the moisture in depths of 100 cm, 150 cm and 220 cm. The fasciculate root system of the grasses increased the infiltration of water at the top of the soil, favouring the formation of more superficial saturation zones in the heavy rains, due to the hydraulic discontinuities. In forest areas, infiltration by preferential paths allows the concentration of water in the depths in which they are terminal increasing the pore water pressure. Soil saturation in this area also occurred in heavy rains, but more deeply due to the rapid movement and redirection of water in depth by tree roots. This process was also responsible for the higher subsurface flows found in the forest, that is, the greater aggregation of the soil, the existence of interconnected macropores, ducts and roots facilitate the transmission of water in depth. Associated with the high rainfall and high relative humidity, these vegetation favoured the formation of saturation zones and increased pore pressures of the water, causing landslides on lands between 0.5 m and 2.0 m. The results of hydraulic conductivity show that the difference (lateritic = 10-4 cm/s; saprolitic = 10-5 cm/s) between the layers of the soil can generate zones of hydraulic discontinuity in extreme rainfall events, which would justify the predominance of shallow translational landslides at these same depths.

Sedimentology and arsenic pollution in the Bengal Basin: insight into arsenic occurrence and subsurface geology.

NASA Astrophysics Data System (ADS)

Hills, Andrew; McArthur, John

2014-05-01

The Bengal delta system is a geologically recent feature overlying a deeply incised palaeo-surface formed during the Last Glacial Maximum. This surface is a series of terraces and valleys created by river incision (Goodbred & Kuehl 2003). The terraces were weathered, forming a thin, indurated laterite deposit (Goodbred & Kuehl 2000) at depths greater than 50 m. McArthur et al. (2008) define this as a palaeosol and have identified it at depths greater than 30 m though out Bangladesh and West Bengal. It has been observed that arsenic concentrations at these sites are lower than the rest of the delta. It has been assumed that the surface morphology at sites where there is a palaeosol are similar and can therefore be characterised by remote sensing, in the form of Google Earth images. Sites were selected in Bangladesh and West Bengal, from work by McArthur et al. (2011); Hoque et al. (2012), where groundwater chemistry and sedimentology data are available making it possible to determine if the subsurface is a palaeo-channel or palaeo-interfluve. Arsenic concentration data have been inputted into Google Earth and the palaeo-channels marked where the arsenic concentration is greater than 10 µg/L, and palaeo-interfluves where arsenic concentration is less than 10 µg/L. The surface morphologies in these domains have been examined for similarities, and it was shown that avulsion scars and abandoned river channels are found where arsenic concentrations are greater than 10 µg/L. Conversely the surrounding areas that are devoid of channel scars have arsenic concentrations less than 10 µg/L. Using the correlation between avulsion features being representative of palaeo-channels and high arsenic concentrations, sites were selected that had a similar surface morphology to the type localities. A comparison of these images and arsenic concentrations showed that the postulate is valid for over 80 percent of cases. Where this is not valid, this could indicate that the subsurface is more complex than previously thought. References 1. Goodbred, S. L. & Kuehl, S. A. 2000. Enormous Ganges-Brahmaputra sediment discharge during strengthened early Holocene monsoon. Geology, 28, 1083-1086. 2. Goodbred, S. L., Kuehl, S. A., Steckler, M. S., & Sarkar, M. H. 2003. Controls on facies distribution and stratigraphic preservation in the Ganges-Brahmaputra delta sequence. Sedimentary Geology, 155, 301-316. 3. Hoque, M. A., McArthur, J. M., & Sikdar, P. K. 2012. The palaeosol model of arsenic pollution of groundwater tested along a 32 km traverse across West Bengal, India. Science of the Total Environment, 431, 157-165. 4. McArthur, J. M., Ravenscroft, P., Banerjee, D. M., Milsom, J., Hudson-Edwards, K. A., Sengupta, S., Bristow, C., Sarkar, A., & Purohit, R. 2008. How palaeosols influence groundwater flow and arsenic pollution: A model from the Bengal Basin and its worldwide implication. Water Resources Research, 44, W11411, doi: 10.1029/2007WR0067552. 5. McArthur, J. M., Nath, B., Banerjee, D. M., Purohit, R., & Grassineau, N. 2011. Palaeosol control on groundwater flow and pollutant distribution: The example of arsenic. Environmental Science and Technology, 45, 1376-1383.

Geochemistry of Selected Coal Samples from Sumatra, Kalimantan, Sulawesi, and Papua, Indonesia

USGS Publications Warehouse

Belkin, Harvey E.; Tewalt, Susan J.

2007-01-01

Introduction Indonesia is an archipelago of more than 17,000 islands that stretches astride the equator for about 5,200 km in southeast Asia (figure 1) and includes major Cenozoic volcano-plutonic arcs, active volcanoes, and various related onshore and offshore basins. These magmatic arcs have extensive Cu and Au mineralization that has generated much exploration and mining in the last 50 years. Although Au and Ag have been mined in Indonesia for over 1000 years (van Leeuwen, 1994), it was not until the middle of the nineteenth century that the Dutch explored and developed major Sn and minor Au, Ag, Ni, bauxite, and coal resources. The metallogeny of Indonesia includes Au-rich porphyry Cu, porphyry Mo, skarn Cu-Au, sedimentary-rock hosted Au, epithermal Au, laterite Ni, and diamond deposits. For example, the Grasberg deposit in Papua has the world's largest gold reserves and the third-largest copper reserves (Sillitoe, 1994). Coal mining in Indonesia also has had a long history beginning with the initial production in 1849 in the Mahakam coal field near Pengaron, East Kalimantan; in 1891 in the Ombilin area, Sumatra, (van Leeuwen, 1994); and in South Sumatra in 1919 at the Bukit Asam mine (Soehandojo, 1989). Total production from deposits in Sumatra and Kalimantan, from the 19thth century to World War II, amounted to 40 million metric tons (Mt). After World War II, production declined due to various factors including politics and a boom in the world-wide oil economy. Active exploration and increased mining began again in the 1980's mainly through a change in Indonesian government policy of collaboration with foreign companies and the global oil crises (Prijono, 1989). This recent coal revival (van Leeuwen, 1994) has lead Indonesia to become the largest exporter of thermal (steam) coal and the second largest combined thermal and metallurgical (coking) coal exporter in the world market (Fairhead and others, 2006). The exported coal is desirable as it is low sulfur and ash (generally <1 and < 10 wt.%, respectively). Coal mining for both local use and for export has a very strong future in Indonesia although, at present, there are concerns about the strong need for a major revision in mining laws and foreign investment policies (Wahju, 2004; United States Embassy Jakarta, 2004). The World Coal Quality Inventory (WoCQI) program of the U.S. Geological Survey (Tewalt and others, 2005) is a cooperative project with about 50 countries (out of 70 coal-producing countries world-wide). The WoCQI initiative has collected and published extensive coal quality data from the world's largest coal producers and consumers. The important aspects of the WoCQI program are; (1) samples from active mines are collected, (2) the data have a high degree of internal consistency with a broad array of coal quality parameters, and (3) the data are linked to GIS and available through the world-wide-web. The coal quality parameters include proximate and ultimate analysis, sulfur forms, major-, minor-, and trace-element concentrations and various technological tests. This report contains geochemical data from a selected group of Indonesian coal samples from a range of coal types, localities, and ages collected for the WoCQI program.

A Preliminary Investigation of the Yallalie Basin: A Buried 15 KM Diameter Structure of Possible Impact Origin in the Perth Basin, Western Australia

NASA Astrophysics Data System (ADS)

Dentith, M. C.; Bevan, A. W. R.; McInerney, K. B.

1992-07-01

In late 1990, Ampol Exploration drew the attention of the senior author to an enigmatic structure located in Mesozoic rocks in the Dandaragan Trough of the Perth Basin about 200 km north of Perth, Western Australia. The basin-like Yallalie structure, centred on coordinates ca. 30 degrees 28'S, 115 degrees 47'E, is subcircular in plan view and about 15 km in diameter. Recognizing structures beneath the basin likely to contain oil, Ampol carried out an intensive geophysical survey of the area, and subsequently drilled a well (Yallalie 1). The well proved to be dry and exploration ceased. Generously, Ampol and their partners have made available the results of their exploration for a research project into the nature of the structure. Geology and regional setting: The exposed geology of the Yallalie basin area comprises discontinuous sequences of sedimentary rocks (sandstones, siltstones and shales) of Middle Jurassic to Late Cretaceous age that are capped by laterite and locally covered by thin (<50 m) Cenozoic eolian, colluvial and alluvial deposits (Cockbain, 1990). Modern, high-resolution, seismic reflection profiles across the Yallalie structure show a basin-shaped area of chaotic reflections that extend down to a depth of approximately 2 km below the surface. The structure has sharp boundaries with surrounding faulted, but otherwise relatively undisturbed rocks. At the base of the structure there is a central uplifted area approximately 3-4 km across similar to those described from complex impact structures (Dence et al., 1977). A preliminary survey of the area has shown that exposed rocks of the Yarragadee Formation (Middle Jurassic to Lower Cretaceous) and the succeeding Warnbro (Lower Cretaceous) and Coolyena (Late Cretaceous) Groups dip gently and their deposition appears to have postdated the underlying structure of intensely disturbed rocks. Although the structure is "draped" by a thin (a few hundred metres) veneer of late Jurassic to Cretaceous rocks it has some surface expression. A broad depression approximately 120 m deep is centered on Yallalie Well and is bounded to the west and north by a marked "rim." The area is characterized by a radial pattern of drainage that flows into the depression and which is gradually exhuming the buried structure. A southerly flowing stream drains the depression and has breached the "rim" to the south. Evidence for impact at Yallalie: Quartz grains taken from the core at a depth of 430-460 m in the Yallalie 1 well show widesprad development of prismatic cleavage fractures and irregular, slightly curved planes formed by brittle fracture. Quartz grains from a depth of 150-180 m in the well are essentially undeformed (McInerney, 1991). However, multiple sets of closely spaced planar features in quartz, characteristic of highly shocked rocks, have yet to be observed in core material from the Yallalie structure. Nevertheless, the morphology of the Yallalie structure determined from geophysical data suggests strongly that it is of impact origin. Work is continuing on the core material to search for diagnostic shock-metamorhic effects, and to constrain the age of the structure. References Cockbain A. E. (1990) In Geology and Mineral Resources of Western Australia, Western Australia Geological Survey, Memoir 3, pp. 514-516. Dence M. R., Grieve R. A. F., and Robertson P. B. (1977) In Impact and Explosion Cratering (eds. D. J. Roddy, R. O. Pepin, and R. B. Merrill), Pergamon Press, pp. 247-275. McInerney K. B. (1991) Honors Thesis (unpublished), University of Western Australia.

Genesis of the Doğankuzu and Mortaş Bauxite deposits, Taurides, Turkey: separation of Al, Fe, and Mn and implications for passive margin metallogeny

USGS Publications Warehouse

Öztürk, Hüseyin; Hein, James R.; Hanilçi, Nurullah

2002-01-01

The Taurides region of Turkey is host to a number of important bauxite, Al-rich laterite, and Mn deposits. The most important bauxite deposits, Doğankuzu and Mortaş, are karst-related, unconformity-type deposits in Upper Cretaceous limestone. The bottom contact of the bauxite ore is undulatory, and bauxite fills depressions and sinkholes in the footwall limestone, whereas its top surface is concordant with the hanging-wall limestone. The thickness of the bauxite varies from 1 to 40 m and consists of böhmite, hematite, pyrite, marcasite, anatase, diaspore, gypsum, kaolinite, and smectite. The strata-bound, sulfide- and sulfate-bearing, low-grade lower part of the bauxite ore bed contains pyrite pseudomorphs after hematite and is deep red in outcrop owing to supergene oxidation. The lower part of the bauxite body contains local intercalations of calcareous conglomerate that formed in fault-controlled depressions and sinkholes. Bauxite ore is overlain by fine-grained Fe sulfide-bearing and calcareous claystone and argillaceous limestone, which are in turn overlain by massive, compact limestone of Santonian age. That 50-m-thick limestone is in turn overlain by well-bedded bioclastic limestone of Campanian or Maastrichtian age, rich with rudist fossils. Fracture fillings in the bauxite orebody are up to 1 m thick and consist of bluish-gray-green pyrite and marcasite (20%) with böhmite, diaspore, and anatase. These sulfide veins crosscut and offset the strata-bound sulfide zones. Sulfur for the sulfides was derived from the bacterial reduction of seawater sulfate, and Fe was derived from alteration of oxides in the bauxite. Iron sulfides do not occur within either the immediately underlying or overlying limestone. The platform limestone and shale that host the bauxite deposits formed at a passive margin of the Tethys Ocean. Extensive vegetation developed on land as the result of a humid climate, thereby creating thick and acidic soils and enhancing the transport of large amounts of organic matter to the ocean. Alteration of the organic matter provided CO2 that contributed to formation of a relatively 12C-rich marine footwall limestone. Relative sea-level fall resulted from strike-slip faulting associated with closure of the ocean and local uplift of the passive margin. That uplift resulted in karstification and bauxite formation in topographic lows, as represented by the Doğankuzu and Mortaş deposits. During stage 1 of bauxite formation, Al, Fe, Mn, and Ti were mobilized from deeply weathered aluminosilicate parent rock under acidic conditions and accumulated as hydroxides at the limestone surface owing to an increase in pH. During stage 2, Al, Fe, and Ti oxides and clays from the incipient bauxite (bauxitic soil) were transported as detrital phases and accumulated in the fault-controlled depressions and sinkholes. During stage 3, the bauxitic material was concentrated by repeated desilicification, which resulted in the transport of Si and Mn to the ocean through a well-developed karst drainage system. The transported Mn was deposited in offshore muds as Mn carbonates. The sulfides also formed in stage 3 during early diagenesis. Transgression into the foreland basin resulted from shortening of the ocean basin and nappe emplacement during the latest Cretaceous. During that time bioclastic limestone was deposited on the nappe ramp, which overlapped bauxite accumulation.

The Lake Albert Rift (uganda, East African Rift System): Deformation, Basin and Relief Evolution Since 17 Ma

NASA Astrophysics Data System (ADS)

Brendan, Simon; François, Guillocheau; Cécile, Robin; Olivier, Dauteuil; Thierry, Nalpas; Martin, Pickford; Brigitte, Senut; Philippe, Lays; Philippe, Bourges; Martine, Bez

2016-04-01

This study is based on a coupled basin infilling study and a landforms analysis of the Lake Albert Rift located at the northern part of the western branch of the East African Rift. The basin infilling study is based on both subsurface data and outcrops analysis. The objective was to (1) obtain an age model based on onshore mammals biozones, (2) to reconstruct the 3D architecture of the rift using sequence stratigraphy correlations and seismic data interpretation, (3) to characterize the deformation and its changes through times and (4) to quantify the accommodation for several time intervals. The infilling essentially consists of isopach fault-bounded units composed of lacustrine deposits wherein were characterized two major unconformities dated at 6.2 Ma (Uppermost Miocene) and 2.7 Ma (Pliocene-Pleistocene boundary), coeval with major subsidence and climatic changes. The landforms analysis is based on the characterization and relative dating (geometrical relationships with volcanism) of Ugandan landforms which consist of stepped planation surfaces (etchplains and peplians) and incised valleys. We here proposed a seven-steps reconstruction of the deformation-erosion-sedimentation relationships of the Lake Albert Basin and its catchments: - 55-45 Ma: formation of laterites corresponding to the African Surface during the very humid period of the Lower-Middle Eocene; - 45-22: stripping of the African Surface in response of the beginning of the East-African Dome uplift and formation of a pediplain which associated base level is the Atlantic Ocean; - 17-2.5 Ma: Initiation of the Lake Albert Basin around 17 Ma and creation of local base levels (Lake Albert, Edward and George) on which three pediplains tend to adapt; - 18 - 16 Ma to 6.2 Ma: "Flexural" stage (subsidence rate: 150-200 m/Ma; sedimentation rate 1.3 km3/Ma between 17 and 12 Ma and 0.6 km3/Ma from 12 to 6 Ma) - depocenters location (southern part of Lake Albert Basin) poorly controlled by fault; - 6.2 Ma to 2.5 Ma: Rift stage 1 (subsidence rate: > 500m/Ma up to 600-800 m/Ma; sedimentation rate: 2.4 km3/Ma) - Rifting climax; - 2.5-0.4 Ma: uplift of the Ruwenzori Mountains and shifting from an alluvial system to a network of bedrock river incision - Rift Stage 2 (subsidence rate: 450 to 250 m/Ma; sedimentation rate: 1.5 km3/Ma); - 0.4-0 Ma: long wavelength downwarping of the Tanzanian Craton, initiation of the Lake Victoria trough, drainage network inversion and uplift of the present-day Ugandan escarpment (normal faulting motion of the border faults) with formation of perched valleys associated to the Lower Pleistocene (2.5-0.4 Ma) rivers network. At larger scale, comparison of the Lake Albert Rift evolution with the data available in the basins of both eastern and western branches of the East African Rift System shows that most of the sedimentary basins experienced the same geometrical evolution from large basins with limited fault controls during Late Miocene to narrow true rift in Late Pleistocene (e.g. Northern and Central Kenyan Basins), in agreement with the volcanism distribution, large (width >100 km) during the Miocene times, narrower (width x10 km) from Late Pliocene to Pleistocene times and today limited to narrow rifts.

A lithofacies terrain model for the Blantyre Region: Implications for the interpretation of palaeosavanna depositional systems and for environmental geology and economic geology in southern Malawi

NASA Astrophysics Data System (ADS)

Dill, H. G.; Ludwig, R.-R.; Kathewera, A.; Mwenelupembe, J.

2005-06-01

The Blantyre City Area is part of the African savanna in southern Malawi. Sedimentological, geomorphological, chemical and mineralogical studies were conducted to create a lithofacies terrain model. The project involves mapping, cross-sectioning, grain size, heavy mineral analysis, XRD and the study of sedimentary textures under the petrographic microscope. These classical techniques were combined with GIS-based field and office works. The combined efforts led to 2-D maps and 3-D block diagrams that illustrate the geomorphological and sedimentological evolution of the landscape in southern Malawi during the late Mesozoic and Cenozoic. The results obtained through integrated geomorphological-sedimentological studies form the basis for land management (planning of residential areas, waste disposal sites, assessment of bearing capacity of rocks), geohazard prediction (delineation of high risk zones in terms of mass flow and inundation) and the evaluation of high-place (ceramic raw materials) and high-unit value (placers of precious metals and gemstones) mineral commodities in the study area. The study addresses regional and general aspects alike. In regional terms, the study aimed at unraveling the evolution of landforms at the southern end of the East African Rift System during the most recent parts of the geological past. Four stages of peneplanation were established in the working area. Planation was active from the Cretaceous to the Quaternary (stage I: early to mid-Cretaceous, stage II: early Tertiary, stage III: early to mid-Tertiary, stage IV: mid- to late Tertiary). During the most recent parts of the Quaternary, strong fluvial incision was triggered by the base-level lowering of the Shire River. Geomorphological alteration of the landscape goes along with a phyllosilicate-sesquioxide transformation from minerals indicative of more acidic meteoric fluids (e.g., gibbsite, kaolinite) to those typical of more alkaline conditions (e.g. smectite, vermiculite, hydrobiotite). In addition, the investigation is to provide some characteristic features suitable for the recognition and interpretation of terrestrial environments resembling the present-day savanna in the ancient sedimentary record: Conspicuous bimodality in the grain-size distribution. High degree of gravel roundness. Boulder fields (basal conglomerates) with fitting breccias and no rotation of structural elements. Poor to very poor sorting of siliciclastics. Stratification is rare; if present only in sandy beds with antidune and tabular cross-bedding at low angle prevailing over cross-bedding at high angle. Grading rare; in arenaceous deposits poorly developed FU sequences, in rudites poorly developed CU sequences, locally with surface armoring. Directional sedimentary structures in coarse-grained deposits are unimodal. Fabric types: a(t)b(i) and a(p)b(i); shear planes indicative of slide may be present. Ribbon-shaped architectural elements prevail over channel-like types. Bounding surfaces/unconformities are uneven to wavy and more widespread than scour-and-pool structures. Fine-grained carbonaceous interbeds are restricted to shallow depressions. Etch marks such as tafonis, flutes, honeycomb textures are common. Placer deposits of metallic and non-metallic mineral commodities are abundant. Alucretes and ferricretes of bog iron (ferrihydrite > goethite) and lateritic (goethite > ferrihydrite) types are common, calcitic freshwater limestones and gypcretes are scarce. Kandite-group minerals "in" (relic), smectite-group minerals "in", vermiculite "in" (recent), mica-group minerals "out".

Hydrology and Soil Erosion in Tropical Rainforests and Pasture Lands on the Atherton Tablelands, North Queensland, Australia - a rainfall simulator study

NASA Astrophysics Data System (ADS)

Joanne, Joanne; Ciesiolka, Cyril

2010-05-01

The Barron and Johnstone Rivers rise in the basaltic Atherton Tableland, North Queensland, Australia, and flow into the Coral Sea and Great Barrier Reef World Heritage Area (GBRWHA). Natural rainforest in this region was cleared for settlement in the early 20th century. Rapid decline in soil fertility during the 1940's and 50's forced landholders to turn to pasture based industries from row crop agriculture. Since then, these pasture based industries have intensified. The intensified land use has been linked to increases in sediment and nutrient levels in terrestrial runoff and identified as a major environmental threat to the GBRWHA, which has raised alarm for the tourist industry and resource managers. Studies linking land-use to pollutant discharge are often based on measurements and modelling of end of catchment measurements of water quality. Whilst such measurements can be a reasonable indicator of the effects of land use on pollutant discharge to waterways, they are often a gross assessment. This project used rainfall simulations to investigate the relationship between land use and management with sources and sinks of runoff and soil erosion within the Barron and Johnstone Rivers catchments. Rainfall simulations were conducted and pollutant loads measured in natural rainforest, as well as dairy and beef farming systems. The dairy farming systems included an effluent fed pasture, a high mineral fertilizer and supplementary irrigation farm, and a rainfed organic pasture that relied on tropical legumes and introduced grasses and returned organic material to the soil. One of the beef farming systems used a 7-10 day rotation with a low fertilizer regime (kikuyu mostly), while the other, used a long period- two paddock-rotation with no fertiliser and paspalum pastures. The rainforests were generally small isolated enclaves with a well developed shrub layer (1-3 m), and a presence of scattered, deciduous trees. Simulations were carried out on sites which were observed to be part of a drainage network and which were typical of the surrounding hillslopes. A 13 m long by 2 m wide portable rainfall simulator was used to produce rainfall associated with high intensity events. The simulator consisted of six A-frame modules with spray nozzles (equipped with pressure gauges) that operated in an oscillating movement. Rainfall from the simulator was measured using seven dynamically calibrated pluviometers (~0.1mm/tip) and 26 rain gauges (100mm diameter, muslin covered). Runoff volume was recorded using a tipping bucket mechanism. Samples were collected at three minute intervals and used to calculate soil loss using standard methods. At sites where there was a high rate of infiltration a catena effect on runoff could be discerned. Highest runoff volumes tended to be generated on the midslope, rectilinear segments of the hillslope. However some of the sites exhibited effects from indurated laterite layers, exfiltration areas, and small areas of unweathered basalt veneered by a surface ferrasol. All sites had high levels of vegetative cover but large differences in biomass. While runoff and soil erosion were not significantly correlated with vegetative cover, a useful relationship was found when cover was multiplied by biomass. The rate of soil loss from intensive dairying was less than from the intensive beef grazing sites and cattle tracks. However, because deposition from these point sources occurred it became difficult to verify whether contributions from overland flow to the stream were significant. Observations of farm dam overflows near to the simulation sites confirmed the significant subsurface flows that diluted sediment concentrations in the local waterways. Overall, the results indicated that to reduce sediment loss farms must be designed and managed according to landscape features. In order to better understand runoff and sediment delivery it would be necessary to measure volumes and rates through a 'nested' catchment approach so that stream channel contributions could be quantified.

The limitations of seedling growth and drought tolerance to novel soil substrates in arid systems: Implications for restoration success

NASA Astrophysics Data System (ADS)

Bateman, Amber; Lewandrowski, Wolfgang; Stevens, Jason; Muñoz-Rojas, Miriam

2016-04-01

Introduction With the limited knowledge available regarding the impact of drought on seedling growth, an understanding of seedling tolerance to arid conditions is crucial for restoration success (James et al., 2013; Muñoz-Rojas et al., 2014). However, restoration in semi-arid areas faces the challenge of re-establishing plant communities on altered soil substrates (Muñoz-Rojas et al., 2015). These substrates are a result of anthropogenic disturbances such as mining which have altered the plant-soil-water dynamics of the ecosystem (Machado et al., 2013). The aim of this study was to assess the impact of mining on the plant-soil-water dynamics of an arid ecosystem of Western Australia (Pilbara region, North Western Australia) and the implications these altered relationships have on seedling growth and their responses to drought. Methods Drought responses of native plant species were assessed through a series of glasshouse experiments. Firstly, 21 species dominant to the Pilbara region were subjected to drought in a topsoil growth media to assess variation in responses (leaf water potential at the time of stomatal closure) across species and identify traits associated with drought tolerance. Secondly, four species ranging in their drought tolerance identified previously, were grown to two leaf stages (second and fourth leaf stage) in three mining substrates (topsoil, a topsoil and waste mix and waste) to assess seedling drought responses to various potential restoration substrates and how that varied with plant development stage. Results and discussion Four morphological traits were found to be significantly associated with drought indicators (leaf mass ratio, stem area, stem length, stem weight), however, these were weak correlations. Waste substrate and its addition to topsoil reduced plant total biomass but did not alter species responses to drought. However, the soil physical properties of the waste reduced water retention and water availability for plant uptake resulting in seedling mortality at less negative soil water potential. Finally, no significant differences in drought tolerance were observed between the two leaf stages across the four species tested. Analysis of plant desiccation curves found the advanced leaf stage to be less tolerant of drought as shown by a decrease in soil water potential at the time of stomatal closure. Species possess a range of morphological traits, some of which are associated with drought tolerance. However, these traits on their own may not be main drivers for drought resilience and other factors play a role, for example soil nutrient availability. Materials tested in this study that may be available to create novel restoration substrates hinder plant growth but not necessarily plant responses to drought. These findings go a long way to defining some of the limitations of seedling growth and the degree of drought tolerance which will assist in the management of post-mining restoration. References James, J.J., Sheley, R.L., Erickson,T., Rollins, K.S., Taylor, M.H., Dixon, K.W. (2013) A systems approach to restoring degraded drylands. Journal of Applied Ecology 50:730-739. Machado, N. A. M., Leite, M. G. P., Figueiredo, M. A., Kozovits, A. R. (2013) Growing Ereman-thus erythropappus in crushed laterite: A promising alternative to topsoil for baux¬ite-mine revegetation. Journal of Environmental Management 129: 149-156. Muñoz-Rojas, M., Erickson, T., Merritt, D., Dixon, K. (2014) Optimising post-mining soil conditions to maximise restoration success in a biodiverse semiarid environment. Geophysical Research. Abstracts Vol. 16, EGU2014-2069-1, EGU General Assembly. Muñoz-Rojas, M., Erickson, T., Merritt, D., Dixon, K. (2015) Applying soil science for restoration of post mining degraded landscapes in semi-arid Australia: challenges and opportunities. Geophysical Research. Abstracts Vol. 17, EGU2015-3967-1, EGU General Assembly.

Vanadium

USGS Publications Warehouse

Kelley, Karen D.; Scott, Clinton T.; Polyak, Désirée E.; Kimball, Bryn E.; Schulz, Klaus J.; DeYoung,, John H.; Seal, Robert R.; Bradley, Dwight C.

2017-12-19

Vanadium is used primarily in the production of steel alloys; as a catalyst for the chemical industry; in the making of ceramics, glasses, and pigments; and in vanadium redox-flow batteries (VRBs) for large-scale storage of electricity. World vanadium resources in 2012 were estimated to be 63 million metric tons, which include about 14 million metric tons of reserves. The majority of the vanadium produced in 2012 was from China, Russia, and South Africa.Vanadium is extracted from several different types of mineral deposits and from fossil fuels. These deposits include vanadiferous titanomagnetite (VTM) deposits, sandstone-hosted vanadium (with or without uranium) deposits (SSV deposits), and vanadium-rich black shales. VTM deposits are the principal source of vanadium and consist of magmatic accumulations of ilmenite and magnetite containing 0.2 to 1 weight percent vanadium pentoxide (V2O5). SSV deposits are another important source; these deposits have average ore grades that range from 0.1 to greater than 1 weight percent V2O5. The United States has been and is currently the main producer of vanadium from SSV deposits, particularly those on the Colorado Plateau. Vanadium-rich black shales occur in marine successions that were deposited in epeiric (inland) seas and on continental margins. Concentrations in these shales regularly exceed 0.18 weight percent V2O5 and can be as high as 1.7 weight percent V2O5. Small amounts of vanadium have been produced from the Alum Shale in Sweden and from ferrophosphorus slag generated during the reduction of phosphate to elemental phosphorus in ore from shales of the Phosphoria Formation in Idaho and Wyoming. Because vanadium enrichment occurs in beds that are typically only a few meters thick, most of the vanadiferous black shales are not currently economic, although they may become an important resource in the future. Significant amounts of vanadium are recovered as byproducts of petroleum refining, and processing of coal, tar sands, and oil shales may be important future sources.Vanadium occurs in one of four oxidation states in nature: +2, +3, +4, and +5. The V3+ ion has an octahedral radius that is almost identical to that of (Fe3+) and (Al3+) and, therefore, it substitutes in ferromagnesian minerals. During weathering, much of the vanadium may partition into newly formed clay minerals, and it either remains in the +3 valence state or oxidizes to the +4 valence state, both of which are relatively insoluble. If erosion is insignificant but chemical leaching is intense, the residual material may be enriched in vanadium, as are some bauxites and laterites. During the weathering of igneous, residual, or sedimentary rocks, some vanadium oxidizes to the +5 valence state, especially in the intensive oxidizing conditions that are characteristic of arid climates.The average contents of vanadium in the environment are as follows: soils [10 to 500 parts per million (ppm)]; streams and rivers [0.2 to 2.9 parts per billion (ppb)]; and coastal seawater (0.3 to 2.8 ppb). Concentrations of vanadium in soils (548 to 7,160 ppm) collected near vanadium mines in China, the Czech Republic, and South Africa are many times greater than natural concentrations in soils. Additionally, if deposits contain sulfide minerals such as chalcocite, pyrite, and sphalerite, high levels of acidity may be present if sulfide dissolution is not balanced by the presence of acid-neutralizing carbonate minerals. Some of the vanadium-bearing deposit types, particularly some SSV and black-shale deposits, contain appreciable amounts of carbonate minerals, which lowers the acid-generation potential.Vanadium is a micronutrient with a postulated requirement for humans of less than 10 micrograms per day, which can be met through dietary intake. Primary and secondary drinking water regulations for vanadium are not currently in place in the United States. Vanadium toxicity is thought to result from an intake of more than 10 to 20 milligrams per day. Vanadium is essential for some biological processes and organisms. For example, some nitrogen-fixing bacteria require vanadium for producing enzymes necessary to convert nitrogen from the atmosphere into ammonia, which is a more biologically accessible form of nitrogen.

Geochronology of the Baye Mn oxide deposit, southern Yunnan Plateau: Implications for the late Miocene to Pleistocene paleoclimatic conditions and topographic evolution

NASA Astrophysics Data System (ADS)

Deng, Xiao-Dong; Li, Jian-Wei; Vasconcelos, Paulo M.; Cohen, Benjamin E.; Kusky, Timothy M.

2014-08-01

40Ar/39Ar laser incremental heating analyses of supergene K-Mn oxides from weathering profiles at the Baye Mn deposit, southern Yunnan Plateau, SW China, were carried out to place constraints on the timing of weathering and derive insights into local paleoclimatic and landscape evolution. Weathering profiles in the Baye Mn mine are dominated by 20-30 m thick saprolites, which are locally covered by unconsolidated alluvial deposits. We analyzed 70 grains from 35 hand samples collected from four sites located at distinct elevations. In most cases, different grains from the same hand sample and different samples from the same site have reproducible 40Ar/39Ar plateau ages. The plateau ages of individual grains are also consistent with the respective isochron, integrated, and ideogram ages. This age consistency attests to the reliability of the geochronological results as numerical constraints on the formation and evolution of these weathering profiles. Sixty-four grains from 32 hand samples collected from weathering profiles at four sites (A to D) yield well-defined plateau or pseudoplateau ages ranging from 2.98 ± 0.07 to <0.16 Ma (2σ). The age results show that Mn oxides become progressively younger towards lower elevations: samples collected from the highest elevation site (∼1855 m a.s.l.) have the oldest ages at 2.98 ± 0.07 to 2.83 ± 0.13 Ma; samples from intermediate elevations (1821 to 1815 m a.s.l.) yield ages ranging from 2.91 ± 0.10 to 2.08 ± 0.11 Ma; and those from the lowest sites (1768 to 1753 m a.s.l.) are younger than 1.25 ± 0.08 Ma. The age versus elevation relationship indicates fast downward propagation of weathering front since the late Pliocene, and permits estimating the weathering rates at 3.3 ± 3.8, 6.6 ± 1.2, and 11.1 ± 1.9 m Myr-1 during the time periods of 2.98-2.83, 2.91-2.08, and 1.25 to <0.16 Ma, respectively. The average river incision rates estimated from the surface exposed ages range from 235 ± 10 to 416 ± 19 m Myr-1 during the past 3 million years. The incision rate calculated from minimum exposed ages at sites B-D is 33 ± 2 m Myr-1 for the time period of 2.91-1.25 Ma, which is consistent with the slow incision of streams on the ridges over the Yunnan Plateau since the early Pleistocene. Three Mn oxide pebbles contained in the alluvial deposits overlying the saprolite-dominated weathering profiles at the two highest sites provided additional information on the timing of weathering. Four grains from two pebbles yield plateau ages of 6.32 ± 0.19 to 5.27 ± 0.10 Ma, whereas the other two grains from the third pebble indicate the minimum formation ages of 8.2 ± 0.4 and 9.3 ± 0.3 Ma. These ages confirm the existence of older weathering profiles, now dismantled, in the region. Manganese oxide 40Ar/39Ar ages of the Baye deposit, when combined with results from other localities, indicate that lateritic weathering and supergene Mn enrichment and, by inference, warm and humid climates conducive to intense weathering have prevailed over the Plateau since the middle to late Miocene. The climatic conditions inferred from the weathering geochronology are consistent with multiple independent marine and terrestrial sedimentary and paleontological records, confirming that supergene Mn oxides can be used as a useful proxy for past climate. Age clusters of Mn oxides at 2.9-2.4, 1.2-0.8, and 0.6-0.4 Ma are broadly coincident with and thus likely reflect intensification events of the Indian Summer Monsoon that brings moisture and abundant precipitation to the Yunnan Plateau. These clusters also coincide with the periods of significant surface uplift in the Yunnan Plateau, demonstrating a causal link between topographic evolution, plateau uplift, and intensification of the monsoonal climate.

Paleoenvironments, Evolution, and Geomicrobiology in a Tropical Pacific Lake: The Lake Towuti Drilling Project (TOWUTI)

NASA Astrophysics Data System (ADS)

Vogel, Hendrik; Russell, James M.; Bijaksana, Satria; Crowe, Sean; Fowle, David; Haffner, Douglas; King, John; Marwoto, Ristiyanti; Melles, Martin; von Rintelen, Thomas; Stevenson, Janelle; Watkinson, Ian; Wattrus, Nigel

2014-05-01

Lake Towuti (2.5°S, 121°E) is a, 560 km2, 200-m deep tectonic lake at the downstream end of the Malili lake system, a set of five, ancient (1-2 MYr) tectonic lakes in central Sulawesi, Indonesia. Lake Towuti's location in central Indonesia provides a unique opportunity to reconstruct long-term paleoclimate change in a crucially important yet understudied region- the Indo-Pacific warm pool (IPWP), heart of the El Niño-Southern Oscillation. The Malili Lakes have extraordinarily high rates of floral and faunal endemism, and the lakes are surrounded by one of the most diverse tropical forests on Earth. Drilling in Lake Towuti will identify the age and origin of the lake and the environmental and climatic context that shaped the evolution of this unique lacustrine and terrestrial ecosystem. The ultramafic (ophiolitic) rocks and lateritic soils surrounding Lake Towuti provide metal substrates that feed a diverse, exotic microbial community, analogous to the microbial ecosystems that operated in the Archean Oceans. Drill core will provide unique insight into long-term changes in this ecosystem, as well as microbial processes operating at depth in the sediment column. High-resolution seismic reflection data (CHIRP and airgun) combined with numerous long sediment piston cores collected from 2007-2013 demonstrate the enormous promise of Lake Towuti for an ICDP drilling campaign. Well-stratified sequences of up to 150 m thickness, uninterrupted by unconformities or erosional truncation, are present in multiple sub-basins within Towuti, providing ideal sites for long-term environmental, climatic, and limnological reconstructions. Multiproxy analyses of our piston cores document a continuous and detailed record of moisture balance variations in Lake Towuti during the past 60 kyr BP. In detail our datasets show that wet conditions and rainforest ecosystems in central Indonesia persisted during Marine Isotope Stage 3 (MIS3) and the Holocene, and were interrupted by severe drying between ~33,000 and 16,000 yr BP when high-latitude ice sheets expanded and global temperatures cooled. This in combination with the observed little direct influence of precessional orbital forcing and exposure of the Sunda Shelf implies that central Indonesian hydroclimate varies strongly in response to high-latitude climate forcing: a hypothesis we aim to test across multiple glacial-interglacial cycles through scientific drilling. Indeed, numerous high-amplitude reflectors in the upper 150 m of lacustrine fill suggest repeated cycles of moisture-balance variations in the tropical Pacific. In summary drilling in Lake Towuti will help to: (1) Document the timing, frequency, and amplitude of orbital- to millennial-scale changes in surface hydrology and terrestrial temperature in the Indo-Pacific Warm Pool across multiple glacial-interglacial cycles; (2) Understand how variations in terrestrial hydrology and temperature in central Indonesia respond to changes in the mean state of the ENSO system, the monsoons, high-latitude forcing, and insolation; (3) Analyze the long-term stability and resilience of rainforest vegetation to changes in climate, greenhouse gases, and fire frequency; (4) Study the extent, biogeography, and metabolism of microbial life in the sediments of a non-sulfidic, ferrginous basin, and their relationships to carbon cycling, redox metal deposition, and the concentration of metal ore minerals; (5) Study the effects of climate-driven changes in the aquatic environment on both lacustrine microbial populations, and the geobiosphere within the lake's sediment; (6) Determine the age of Lake Towuti, and the ensuing rates of speciation of Towuti's endemic fauna and flora; (7) Identify the timing of past lake level fluctuations in Towuti, changes in hydrological connections among the Malili Lakes, and how these influenced biological colonization events, habitat stability, and modes of speciation (sympatric, allopatric). Important milestones concerning the operational and logistical preparation of a deep drilling at Lake Towuti have been achieved by the PI team in close collaboration with DOSECC, local authorities and businesses in Indonesia, and ICDP. A drilling proposal has recently been funded through the ICDP and proposals for matching funds have been submitted to national funding agencies in 2013. Drilling operations are envisaged to commence in early 2015.

Source of Australasian Tektites: Investigating Possible Impact Sites in Laos

NASA Astrophysics Data System (ADS)

Schnetzler, C. C.; McHone, J. F.

1995-09-01

Approximately 770,000 years ago an asteroid or comet crashed with the Earth somewhere in southeast Asia, in what was arguably the largest terrestrial impact in the past several 10's of millions of years. Evidence for this impact is not a crater but ejecta from a crater - tektites, microtektites and impact debris - which are found over more than one-tenth of the Earth's surface. Despite its relative youth and the large size of the ejecta field, the structure produced by this impact has not yet been discovered. In the past few years searches have focused on eastern Indochina, specifically in northeast Thailand [1], Cambodia [2] and Laos [3]. In February, 1995 we spent ten days in southern Laos looking for the source crater. The trip was an outgrowth of an investigation using satellite imagery and a digital topographic database, which suggested the impact site might be one of several structures in southern Laos. The primary purpose of the trip was to investigate these structures; a secondary objective was to document tektite localities and to collect samples of known provenance. One crater-like structure identified from digital topographic and multispectral images seemed to be especially interesting due to its quasi-circular shape and relatively youthful appearance. Three additional suspicious structures were identified near this primary target, but these appeared much more subdued and highly eroded. All of these features lie in southern Laos within the broad region of Mesozoic marine sedimentary rocks, primarily sandstones interbedded with shales and limestones, which covers much of central Indochina. The top-priority structure, centered at 16.35 degrees N/106.15 degrees E, is a ring of steep-sided hills 35 to 40 km in diameter, rising 70 to several hundred meters above the surrounding flat plain. It also has a central elevated area rising about 100 meters above the floor, suggesting an eroded central uplift. Despite difficult field conditions we successfully reconnoitered all four potential impact structures. None showed obvious evidence of formation by extraterrestrial impact. A small domal feature near the city of Savannakhet is probably a salt diapir, and a nearby larger eviscerated domal form to the southeast is similarly related to broadscale evaporite tectonics. The 90 km diameter Savannakhet Basin shows no evidence of impact damage and has been a stable sedimentary trap since Mesozoic times. Our prime target, the 35 to 40 km diameter craterlike depression south of Muong Phin, is an erosional feature etched into upper layers of a sedimentary section. Its "central peak" is a fortuitous resistant erosional remnant. Not a great deal of time was available for the secondary objective, i.e., to look for tektites which occur in Indochina in two forms: layered form (Muong Nong-type) which appear to have flowed over the ground and splash form which solidified during atmospheric flight. We identified ten new sites and collected samples from some of these sites. Nine sites were in southern Laos, and all contained only layered tektites. Three of these sites were found by us in road-material quarries south of the village of Xeno. Here the yellow loessial soil overburden had been scraped off to expose a laterite layer rich in quartz pebbles, where small tektites were found after only a short search. This same technique, looking for road-material quarries beside the highway, was used to find layered tektites by Wasson's 1994 field expedition in Thailand [1] about 200 km to the southwest of our areas in Laos. Our new sites support a working theory [3, 4] that this area is rich in layered tektites but there are no splash-form tektites over a broad area of southern NE Thailand and neighboring Laos. The approximate dimensions of this area appears to be at least 200 by 350 km. Acknowledgments: Work was supported in part by NASA and the Barringer Crater Company. References: [1] Wasson J. T. et al. (1995) JGR, in press. [2] Hartung J. and Koeberl C. (1994) Meteoritics, 29, 411-416. [3] Schnetzler C. C. (1992) Meteoritics, 27, 154-165. [4] Wasson J. T. (1993) Eos Trans. AGU, 74, 390.

Kinetic stable Cr isotopic fractionation between aqueous Cr(III)-Cl-H2O complexes at 25 °C: Implications for Cr(III) mobility and isotopic variations in modern and ancient natural systems

NASA Astrophysics Data System (ADS)

Babechuk, Michael G.; Kleinhanns, Ilka C.; Reitter, Elmar; Schoenberg, Ronny

2018-02-01

The stable Cr isotope fractionation preserved in natural substances has been attributed predominantly to Cr(III)-Cr(VI) redox transformations. However, non-redox reaction pathways (e.g., ligand-promoted dissolution, ligand exchange, adsorption of Cr(III)) are liable to contribute to isotopic fractionation in natural systems given that soluble Cr(III)-ligands have been directly documented or modeled in several marine, continental, and hydrothermal environments. This study isolates the stable Cr isotope fractionation accompanying Cl-H2O ligand exchange during the transformation of three aqueous species in the Cr(III)-Cl-H2O system, [CrCl2(H2O)4]+aq (abr. CrCl2+ or S1), [CrCl(H2O)5]2+aq (abr. CrCl2+ or S2), and [Cr(H2O)6]3+aq (abr. Cr3+ or S3), at low pH (≤2). In dilute HCl (0.01 to 1 M), Cr3+ is the kinetically favoured species and transformation of CrCl2+ to CrCl2+ to Cr3+ via 2 steps of dechlorination/hydrolyzation begins immediately upon dissolution of a Cr(III)-Cl solid. Individual species are separated with cation exchange chromatography at different stages of transformation and inter- and intra-species (across an elution peak of one species) isotopic fractionation of up to 1 and 2‰ (δ53/52Cr), respectively, is documented. Comparison of peak elution characteristics with Cr-Cl-H-O isotopologue mass abundances suggests mass-dependent sorting of isotopologues alone cannot explain intra-species fractionation, supporting a previously published proposal that preferential adsorption of light Cr isotopes on the resin is driven by vibrational energy effects. The transformation of CrCl2+ to CrCl2+ is faster than CrCl2+ to Cr3+ and the rates of both transformations increase with solution pH. Preferential reaction of light Cr(III) isotopes into product species occurs during each transformation, consistent with closed-system, kinetic fractionation during Cl-H2O ligand exchange. Inter-species fractionation is assessed using time-series experiments beginning from the dissolution of two Cr(III)-Cl solids (dried NIST SRM979 standard and commercial CrCl3·6H2O salt) in 0.01 M HCl (pH ≈ 2). The ε53/52Cr(CrCl2+/CrCl2+) for the CrCl2+ to CrCl2+ reaction is -0.19‰ (SRM979) and -0.38‰ (salt) and the ε53/52Cr(Cr3+/CrCl2+) for the CrCl2+ to Cr3+ reaction is consistent for both experiments at -0.49‰ (SRM979) and -0.51‰ (salt). Experiments where SRM979 is dissolved in 0.1 and 1 M HCl for a longer aging period provide preliminary evidence that the Cr3+/CrCl2+ Cr(III) isotopic fractionation scales with HCl concentration (transformation rate). Chromium(III) dissolved in 6 M HCl and aged 5 months still yields an inter-species Cr isotope distribution that is apparently inherited from kinetic effects (light Cr isotopes in Cr3+), attesting to the slow development of inter-species isotopic equilibrium, which instead predicts progressively heavier Cr isotopes from CrCl2+ to CrCl2+ to Cr3+. The kinetic Cr(III) isotopic fractionation documented herein is proposed to be relevant to understanding systems where aqueous Cr(III)-Cl species may be temporarily stable (e.g., metamorphic and hydrothermal systems or lateritic weathering). Further, the complexation of Cr(III) with other ligands (e.g., CO32-, organics), combined with additional kinetic effects of Cr(III) potentially occurring in soils or sediment, must be explored prior to establishing the significance of empirical stable Cr isotope signatures in marine and continental environments. Further understanding of non-redox effects may lead to stable Cr isotopes developing as a proxy for system pH or ligand chemistry.

Natural Weathering Rates of Silicate Minerals

NASA Astrophysics Data System (ADS)

White, A. F.

2003-12-01

Silicates constitute more than 90% of the rocks exposed at Earth's land surface (Garrels and Mackenzie, 1971). Most primary minerals comprising these rocks are thermodynamically unstable at surface pressure/temperature conditions and are therefore susceptible to chemical weathering. Such weathering has long been of interest in the natural sciences. Hartt (1853) correctly attributed chemical weathering to "the efficacy of water containing carbonic acid in promoting the decomposition of igneous rocks." Antecedent to the recent interest in the role of vegetation on chemical weathering, Belt (1874) observed that the most intense weathering of rocks in tropical Nicaragua was confined to forested regions. He attributed this effect to "the percolation through rocks of rain water charged with a little acid from decomposing vegetation." Chamberlin (1899) proposed that the enhanced rates of chemical weathering associated with major mountain building episodes in Earth's history resulted in a drawdown of atmospheric CO2 that led to periods of global cooling. Many of the major characteristics of chemical weathering had been described when Merrill (1906) published the groundbreaking volume Rocks, Rock Weathering, and Soils.The major advances since that time, particularly during the last several decades, have centered on understanding the fundamental chemical, hydrologic, and biologic processes that control weathering and in establishing quantitative weathering rates. This research has been driven by the importance of chemical weathering to a number environmentally and economically important issues. Undoubtedly, the most significant aspect of chemical weathering is the breakdown of rocks to form soils, a process that makes life possible on the surface of the Earth. The availability of many soil macronutrients such as magnesium, calcium, potassium, and PO4 is directly related to the rate at which primary minerals weather. Often such nutrient balances are upset by anthropogenic activities. For example, Huntington et al. (2000) show that extensive timber harvesting in the southeastern forests of the United States, which are underlain by intensely weathered saprolites, produces net calcium exports that exceed inputs from weathering, thus creating a long-term regional problem in forest management.The role of chemical weathering has long been recognized in economic geology. Tropical bauxites, which account for most of world's aluminum ores, are typical examples of residual concentration of silicate rocks by chemical weathering over long time periods (Samma, 1986). Weathering of ultramafic silicates such as peridotites forms residual lateritic deposits that contain significant deposits of nickel and cobalt. Ores generated by chemical mobilization include uranium deposits that are produced by weathering of granitic rocks under oxic conditions and subsequent concentration by sorption and precipitation ( Misra, 2000).Over the last several decades, estimating rates of silicate weathering has become important in addressing new environmental issues. Acidification of soils, rivers, and lakes has become a major concern in many parts of North America and Europe. Areas at particular risk are uplands where silicate bedrock, resistant to chemical weathering, is overlain by thin organic-rich soils (Driscoll et al., 1989). Although atmospheric deposition is the most important factor in watershed acidification, land use practices, such as conifer reforestation, also create acidification problems ( Farley and Werritty, 1989). In such environments, silicate hydrolysis reactions are the principal buffer against acidification. As pointed out by Drever and Clow (1995), a reasonable environmental objective is to decrease the inputs of acidity such that they are equal to or less than the rate of neutralization by weathering in sensitive watersheds.The intensive interest in past and present global climate change has renewed efforts to understand quantitatively feedback mechanisms between climate and chemical weathering. On timescales longer than a million years, atmospheric CO2 levels have been primarily controlled by the balance between the rate of volcanic inputs from the Earth's interior and the rate of uptake through chemical weathering of silicates at the Earth's surface (Ruddiman, 1997). Weathering is proposed as the principal moderator in controlling large increases and decreases in global temperature and precipitation through the greenhouse effects of CO2 over geologic time (R. A. Berner and E. K. Berner, 1997). Weathering processes observed in paleosols, discussed elsewhere in this volume (see Chapter 5.18), have also been proposed as indicating changes in Archean atmospheric CO2 and O2 levels (Ohmoto, 1996; Rye and Holland, 1998).

The use of soil quality indicators to assess soil functionality in restored semi-arid ecosystems

NASA Astrophysics Data System (ADS)

Muñoz-Rojas, Miriam; Erickson, Todd E.; Dixon, Kingsley W.; Merritt, David J.

2016-04-01

Keywords: Pilbara, 1-day CO2 test, microbial activity, mine restoration, soil health, ecosystem services. Introduction Semi-arid and arid environments are highly vulnerable to land degradation and their restoration has commonly showed low rates of success (James et al., 2013). A systematic knowledge of soil functionality is critical to successful restoration of degraded ecosystems since approximately 80% of ecosystem services can be connected to soil functions. The assessment of soil functionality generally involves the evaluation of soil properties and processes as they relate to the ability of soil to function effectively as a component of a healthy ecosystem (Costantini et al., 2015) Using soil quality indicators may be a valuable approach to assess functionality of topsoil and novel substrates used in restoration (Muñoz-Rojas et al., 2014; 2015). A key soil chemical indicator is soil organic C, that has been widely used as an attribute of soil quality because of the many functions that it provides and supports (Willaarts et al., 2015). However, microbial indicators can be more sensitive to disturbances and could be a valuable addition in soil assessment studies in restoration programs. Here, we propose a set of soil quality indicators to assess the soil status in restored soils (topsoil and waste material) of semi-arid environments. The study was conducted during March 2015 in the Pilbara biogeographical region (northwestern Australia) at an iron ore mine site rehabilitated in 2011. Methods Soil samples were collected from two sub-areas with different soil materials used as growth media: topsoil retrieved from nearby stockpiles and a lateritic waste material utilised for its erosive stability and physical competence. An undisturbed natural shrub-grassland ecosystem dominated by Triodia spp. and Acacia spp. representative of the restored area was selected as the analogue reference site. Soil physicochemical analysis were undertaken according to standard methods. Soil microbial activity was measured with the 1-day CO2 test, a cost-effective and rapid method to determine soil microbial respiration rate based on the measurement of the CO2 burst produced after moistening dry soil (Muñoz-Rojas et al., 2016). Soil microbial abundance of specific groups was measured by phospholipid fatty acid analysis. Results and discussion We showed that in addition to organic C and C:N ratio, biological indicators (microbial diversity and activity in particular), are the most sensitive indicators to detect differences among reconstructed soils and analogue undisturbed soils in semi-arid areas. The 1-day CO2 test is an alternative cost- and time-effective method to measure microbial activity and assess soil functionality of restored soils. Our results also showed a positive effect of vegetation on reconstructed soils and a recovery of soil functionality in waste material to levels similar to topsoil once vegetation is established, although soil quality levels are still far from those in undisturbed native soils four years post-restoration. Soil functionality is critical in the restoration process, particularly in semi-arid areas, and the methods used here could be effectively applied in a broad range of restoration projects in arid and semi-arid environments. References Costantini EAC, Branquinho C, Nunes A, Schwilch G, Stavi I, Valdecantos A and Zucca C (2015) Soil indicators to assess the effectiveness of restoration strategies in dryland ecosystems. Solid Earth Discussions 7:3645-3687. James JJ, Sheley RL, EricksonT, Rollins KS, Taylor MH, Dixon KW (2013) A systems approach to restoring degraded drylands. Journal of Applied Ecology 50:730-739. Muñoz-Rojas M., Erickson T, Merritt D, Dixon K (2014) Optimising post-mining soil conditions to maximise restoration success in a biodiverse semiarid environment. Geophysical Research. Abstracts Vol. 16, EGU2014-2069-1, EGU General Assembly. Muñoz-Rojas M, Erickson T, Merritt D, Dixon K (2015) Applying soil science for restoration of post mining degraded landscapes in semi-arid Australia: challenges and opportunities. Geophysical Research. Abstracts Vol. 17, EGU2015-3967-1, EGU General Assembly. Muñoz-Rojas M, Erickson TE, Martini D, Dixon KW, Merritt DJ (2016) Soil physicochemical and microbiological indicators of short, medium and long term post-fire recovery in semi-arid ecosystems. Ecological indicators 63:14-22. Willaarts BA, Oyonarte C, Muñoz-Rojas M., Ibáñez JJ and Aguilera PA (2015) Environmental Factors Controlling Soil Organic Carbon Stocks in Two Contrasting Mediterranean Climatic Areas of Southern Spain. Land Degradation and Development (on-line). DOI: 10.1002/ldr.2417

Geology and ground-water resources of the islands of Lanai and Kahoolawe, Hawaii

USGS Publications Warehouse

Stearns, Harold T.; Macdonald, Gordon Andrew; Swartz, Joel Howard

1940-01-01

Lanai lies 59 miles southeast of Honolulu, Oahu, has an area of 141 square miles, and is 3,370 feet high. (See fig. 1 and pl. 1.) Lanai City is the only town of importance. The island produces pineapples and cattle. The surface above about 1,200 feet is generally covered with lateritic soil, which reaches a maximum depth of about 50 feet. Below this level the island is partly devoid of vegetation and is strewn with boulders, the result of having been once submerged by the ocean to this depth. Traces of various emerged and submerged shore lines are described, the highest fossiliferous marine deposits being 1,070 feet above sea level. Lanai is an eroded extinct basaltic volcano built during one period of activity. No secondary eruptions occurred as on most of the other islands. It has three rift zones and a summit caldera. The summit plateau has resulted from collapse along the northwest rift zone. Elsewhere there is much evidence of faulting. About 100 faults and 275 dikes were recorded, but they are so close together in places that it was not possible to show them all on the map.The climate is semitropical, the mean annual temperature of Lanai City, altitude 1,620 feet, being 68° F. Because Lanai lies to the lee of Maui Island it is dry. The mean annual rainfall ranges from 38 inches on the summit to less than 10 inches on the coast. The windward (northeast) side is carved by streams into deep canyons. Maunalei Gulch has the only perennial stream, and it does not reach the sea. Ground water, the lifeblood of Lanai is scarce. Lanai City obtains some of its water supply by a tunnel from gravel in Maumalei Gulch. This water apparently rises from the dike complex in this gulch. The rest of the supply comes from a recently constructed shaft tapping the dike complex not far downstream. The total quantity of high-level ground water discharged by springs and tunnels ranges from about 600,000 gallons a day in wet weather to about 250,000 gallons a day in dry weather. The basal water, although potable, is fairly high in salt. Several sites are recommended for developing and conserving ground water.Kahoolawe Island is 11 miles long, 6 miles wide, 1,491 feet high, covers 45 square miles, and lies 94 miles southeast of Honolulu and 6 3/4 miles southwest of Maui. It is a shield-shaped extinct volcano composed chiefly of thin flows of primitive basalt poured in rapid succession from three rift zones and a vent at their intersection. At one stage the volcano was indented with a caldera about 3 miles across which was later completely filled. A graben led southwestward from it. The rocks are divided into Late Tertiary (?) or early Pleistocene(?) pre-caldera basalts, caldera-filling basalts and basaltic andesites, post-caldera basalts and andesites, and Recent post erosional basalts. A few thin vitric tuff beds and cinder cones were found. Marine erosion has cut cliffs as high as 800 feet along the east and south shores and exposed a cross section of the caldera. Only shallow ephemeral gulches exist. The entire summit has been eroded to a hard-pan surface by the wind as a result of the vegetation being destroyed by livestock. The island is semi-arid and well water is needed for stook: "The stook is now supplied entirely from storage of rain and flood waters. During droughts water is hauled by boat from the island of Maui. All the wells dug so far yield water that is too brackish for stock except at the fairly inaccessible south side of Kanapou Bay. The resistivity survey indicates a water table 1.5 feet or less above sea level for 2.25 miles inland. A few sites for wells are recommended in the dike complex where small supplies of water suitable for stock might be found. Petrographic studies by Gordon A. Macdonald indicate that the pre-caldera and caldera-filling lavas are largely normal olivine basalt of the type which forms the bulk of all Hawaiian volcanoes thus far investigated. It represents the undifferentiated magma of the Hawaiian petrographic province. Toward the close of the caldera-filling epoch the vent became less active, and magmatic differentiation produced basaltic andesites, which are interbedded with normal basalts. The post-caldera lavas are largely basaltic andesites and andesites. The much younger lavas, erupted after a period of extensive erosion, are olivine basalts similar in composition to the pre-caldera flows. The mineralogy of the Kahoolawe rocks is described in detail.

Paleoenvironments, Evolution, and Geomicrobiology in a Tropical Pacific Lake: The Lake Towuti Drilling Project (TOWUTI)

NASA Astrophysics Data System (ADS)

Vogel, Hendrik; Russell, James M.; Bijaksana, Satria; Fowle, David; von Rintelen, Thomas; Stevenson, Janelle; Watkinson, Ian; Marwoto, Ristiyanti; Melles, Martin; Crowe, Sean; Haffner, Doug; King, John

2013-04-01

Lake Towuti (2.5°S, 121°E) is a, 560 km2, 200-m deep tectonic lake at the downstream end of the Malili lake system, a set of five, ancient (1-2 MYr) tectonic lakes in central Sulawesi, Indonesia. Lake Towuti's location in central Indonesia provides a unique opportunity to reconstruct long-term paleoclimate change in a crucially important yet understudied region- the tropical Western Pacific warm pool, heart of the El Niño-Southern Oscillation. The Malili Lakes have extraordinarily high rates of floral and faunal endemism, and the lakes are surrounded by one of the most diverse tropical forests on Earth. Drilling in Lake Towuti will identify the age and origin of the lake and the environmental and climatic context that shaped the evolution of this unique lacustrine and terrestrial ecosystem. The ultramafic (ophiolitic) rocks and lateritic soils surrounding Lake Towuti provide metal substrates that feed a diverse, exotic microbial community, analogous to the microbial ecosystems that operated in the Archean Oceans. Drill core will provide unique insight into long-term changes in this ecosystem, as well as microbial processes operating at depth in the sediment column. While the Malili Lakes have long been considered high-priority drilling sites, only now do we have the requisite site survey information to propose the development of ICDP's first lake drilling target in the tropical western Pacific. High-resolution seismic reflection data (CHIRP and airgun) combined with numerous long sediment piston cores collected from 2007-2010 demonstrate the enormous promise of Lake Towuti for an ICDP drilling campaign. Well-stratified sequences of up to 150 m thickness, uninterrupted by unconformities or erosional truncation, are present in multiple sub-basins within Towuti, providing ideal sites for long-term environmental, climatic, and limnological reconstructions. Multiproxy analyses of our piston cores document a continuous and detailed record of moisture balance variations in Lake Towuti during the past 60 kyr BP, highlighted by arid conditions during northern hemisphere stadials and the last glacial maximum, followed by a dry early and wet late Holocene. This history suggests that climate in central Indonesia responds most strongly to high-latitude climate forcing, despite Indonesia's remote location, and secondarily to southern hemisphere insolation forcing, a hypothesis we aim to test across multiple glacial-interglacial cycles through scientific drilling. Indeed, numerous high-amplitude reflectors in the upper 150 m of lacustrine fill suggest repeated cycles of moisture-balance variations in the tropical Pacific. The principal objectives of our proposed ICDP deep drilling initiative are to: (1) Document the timing, frequency, and amplitude of orbital- to millennial-scale changes in surface hydrology and terrestrial temperature in the Indo-Pacific Warm Pool across multiple glacial-interglacial cycles; (2) Understand how variations in terrestrial hydrology and temperature in central Indonesia respond to changes in the mean state of the ENSO system, the monsoons, high-latitude forcing, and insolation; (3) Analyze the long-term stability and resilience of rainforest vegetation to changes in climate, greenhouse gases, and fire frequency; (4) Study the extent, biogeography, and metabolism of microbial life in the sediments of a non-sulfidic, ferrginous basin, and their relationships to carbon cycling, redox metal deposition, and the concentration of metal ore minerals; (5) Study the effects of climate-driven changes in the aquatic environment on both lacustrine microbial populations, and the geobiosphere within the lake's sediment; (6) Determine the age of Lake Towuti, and the ensuing rates of speciation of Towuti's endemic fauna and flora; (7) Identify the timing of past lake level fluctuations in Towuti, changes in hydrological connections among the Malili Lakes, and how these influenced biological colonization events, habitat stability, and modes of speciation (sympatric, allopatric). We established an international science team, reviewed datasets from the site survey, and selected three drill sites that are best suited to address the objectives of the TOWUTI project during an ICDP and NSF sponsored workshop held in Bandung, Indonesia in March 2012. Important milestones concerning the operational and logistical preparation of a deep drilling at Lake Towuti have been achieved by the PI team in close collaboration with DOSECC, local authorities and businesses in Indonesia, and ICDP. A drilling proposal has been submitted to ICDP in January 2013 and proposals for matching funds will be submitted to national funding agencies in the course of 2013. Drilling operations are envisaged to commence in early 2015.

Hydrological Processes Modifications Induced by Land-Use Changes in the Caetité Region, Northeastern Brazil

NASA Astrophysics Data System (ADS)

Fernandes, N. F.; Franklin, M. R.; Ferraz, A. C.; Reis, R. G.; Melo, V. P.

2009-04-01

Land-use changes can generate important modifications in hydrological processes, especially those that take place close to the soil surface. These changes usually lead to a decrease in infiltration rates and to an increase in surface runoff and soil erosion. Besides, in the long-term, they tend to reduce groundwater recharge. Such effect can be amplified when intensive groundwater pumping is carried out in order to support mining and milling activities. This is the case in the region close to Caetité, in the southwestern portion of Bahia state located in northeastern Brazil, where an already problematic situation in terms of water supply due to the semi-arid conditions is becoming worse due to the exhaustive pumping, mainly for supporting the uranium mining and concentration activities, leading to a variety of potential conflicts concerning the water management in the basin. Since 2008 an experimental basin was installed in the area in order to characterize, through field monitoring and modeling, the evolution of the hydrogeochemical processes in the basin. This study aims, besides the assessment of the water quality, to characterize the effects produced by land-use changes in the hydrological processes that take place at the soil surface, especially on the soil infiltration capacity and saturated hydraulic conductivity (ksat). The Caetité experimental basin has a total area of about 65 km2 that includes portions with natural vegetation (dense and sparse), agriculture (usually small farms), grazing, as well as those resulting from the mining and milling activities (open pit, waste rock piles , industrial plant, ponds and access dirty roads). Although the mining activities have been only recently installed in the area (year of 2000), farmers have been established in the basin for up to 40 years. Average total annual rainfall in the basin is about 710 mm, with a long dry period (from April to October). The geological frame of the area comprises an Archaean gneiss-migmatite complex leading to gentle topography with long convex hillslopes separated by wide flat tops at the divides, where elevations vary from 750 to 1100 m. At the flat tops, thick highly weathered Oxisols (more than 20 m thick) develop over an old lateritic cover. At the lower elevations, hillslope dissection contributed to the formation of less developed and thinner soils, sometimes less than 1m thick. Soil texture may vary significantly inside the basin due to the changes in the mineralogical composition of the different bedrocks, with clay soils developing over alkaline metassomatic rocks. In this study we carried out an initial characterization of the spatial variation of soil infiltration capacity and ksat inside the experimental basin. The infiltration capacity was measured using double-ring infiltrometers (5 cm head). In situ measurements of ksat at 20cm depth were conducted using a Guelph permeameter. These in situ field measurements were carried out in 12 sites in the basin, with 2 repetitions, involving different conditions of land-use (natural vegetation, agriculture and grazing), soil type (Oxisols and Cambisols), geology (granite and gneisses) and topography (flat top and hillslope). Besides, undisturbed soil samples were collected from the upper portion of the soil profile (0-5, 10-15 and 20-25cm depths) to analyze the main physical and hydrological soil properties, including soil texture, bulk density, porosity (micro, macro and total), as well as the water retention curve. The initial results show that areas with dense natural vegetation, independently of soil and topography conditions, present the highest infiltration capacity values in the basin, with minimum infiltration rates (MIR) of up to 100 cm/h. In areas under agriculture, the MIR is reduced by about a factor of 3 when compared with that one of the natural vegetation. MIR values for soils under grazing for more than 10 years show a reduction of up to about a factor of 30, attaining values as low as 3 cm/h. However, long-term grazing in this area tends to favor biogenic activity, mainly by ants. In these areas, the soil disturbing and the pore network produced increase infiltration rates, bringing MIR values to that ones of soil under agriculture. In other words, biogenic activity induced changes due to grazing activity in the area may improve soil infiltration conditions, increasing MIR values by about one order of magnitude. In areas under sparse natural vegetation, splash processes take place favoring surface sealing, leading to MIR values similar to the ones observed for grazing. Differently from what was observed in the infiltration rate, the effects of land-use on ksat are not clear. In general, the greater ksat values observed in the basin were at the main drainage divides, with soil are well-developed over large flat tops. The average ksat value for the basin was 5.68×10-2 cm/s. The results presented here, although preliminary, suggest that the land-use changes that took place in the area during the last decades induced important modifications in the hydrological processes.

Groundwater contamination in the basement-complex area of Ile-Ife, southwestern Nigeria: A case study using the electrical-resistivity geophysical method

NASA Astrophysics Data System (ADS)

Adepelumi, A. A.; Ako, B. D.; Ajayi, T. R.

2001-11-01

Hydrogeoenvironmental studies were carried out at the sewage-disposal site of Obafemi Awolowo University campus, Ile-Ife, Nigeria. The objective of the survey was to determine the reliability of the electrical-resistivity method in mapping pollution plumes in a bedrock environment. Fifty stations were occupied with the ABEM SAS 300C Terrameter using the Wenner array. The electrical-resistivity data were interpreted by a computer-iteration technique. Water samples were collected at a depth of 5.0 m in 20 test pits and analyzed for quality. The concentrations of Cr, Cd, Pb, Zn, and Cu are moderately above the World Health Organization recommended guidelines. Plumes of contaminated water issuing from the sewage ponds were delineated. The geoelectric sections reveal four subsurface layers, with increasing depth, lateritic clay, clayey sand/sand, and weathered/fractured bedrock, and fresh bedrock. The deepest layers, 3 and 4, constitute the main aquifer, which has a thickness of 3.1-67.1 m. The distribution of the elements in the sewage effluent confirms a hydrological communication between the disposal ponds and groundwater. The groundwater is contaminated, as shown by sampling and the geophysical results. Thus, the results demonstrate the reliability of the direct-current electrical-resistivity geophysical method in sensing and mapping pollution plumes in a crystalline bedrock environment. Résumé. Des études géo-environnementales ont été réalisées sur le site d'épandages du campus universitaire d'Obafemi Awolowo, à Ile-Ife (Nigeria). L'objectif de ce travail était de déterminer la fiabilité de la méthode des résistivités électriques pour cartographier les panaches de pollution dans un environnement de socle. Cinquante stations ont été soumises à mesures au moyen d'un ABEM SAS 300C Terrameter en utilisant le dispositif de Wenner. Les données de résistivité électrique ont été interprétées au moyen d'une technique de calcul itérative. Des échantillons d'eau ont été prélevés à une profondeur de 5,0 m dans 20 puits tests et analysés pour la qualité. Les concentrations en Cr, Cd, Pb, Zn et Cu sont légèrement au-dessus des valeurs recommandées par l'OMS. Des panaches d'eau contaminée provenant de bassins d'eaux usées ont été délimités. Les profils géoélectriques mettent en évidence quatre couches, qui sont successivement en profondeurs croissantes une argile latéritique, un sable ou un sable argileux, le substratum altéré, puis fissuré, et enfin le substratum non altéré. Les niveaux 3 et 4 les plus profonds constituent l'aquifère principal, de 3,1-67,1 m d'épaisseur. La distribution des éléments dans les effluents d'égouts confirme l'existence d'une communication hydrologique entre les bassins d'épandage et la nappe. Les eaux souterraines sont contaminées, comme le prouvent les résultats des prélèvements et de la géophysique. Par conséquent, les résultats démontrent la fiabilité de la méthode géophysique de résistivité électrique pour la détection et la cartographie de panaches de pollution dans un environnement de socle cristallin. Resumen. Se ha efectuado un estudio hidrogeológico ambiental en el punto de vertido de las aguas residuales del Campus Universitario de Obafemi Awolowo, en Ile-Ife (Nigeria). El objetivo era determinar la validez del método de la resistividad eléctrica para delimitar penachos de contaminación en un medio rocoso. Se utilizó 50 estaciones con un Terrameter ABEM SAS 300C, utilizando la matriz de Wenner. Se interpretó los resultados por medio de una técnica iterativa automática. Se recogieron muestras de agua a una profundidad de 5 m en 20 pozos de ensayo, las cuales fueron posteriormente analizadas en laboratorio. Las concentraciones de cromo, cadmio, plomo, cinc y cobre son ligeramente superiores a los valores guía de la Organización Mundial de la Salud. Se delineó el penacho de agua contaminada procedente de las balsas de aguas residuales. Las secciones geoeléctricas revelan la existencia de cuatro capas, que están formadas, de menor a mayor profundidad, por arcilla laterítica, arena arcillosa/arena, matriz rocosa meteorizada/fracturada, y roca sin alterar. Las dos capas más profundas constituyen el acuífero principal, que tiene un espesor comprendido entre 3,1-67,1 m. La caracterización química de las aguas residuales confirma que hay una conexión hidrológica entre las balsas de estabilización y las aguas subterráneas. Éstas muestran síntomas de contaminación, de acuerdo con el muestreo y la interpretación geofísica. Los datos evidencian la fiabilidad del método geofísico de la resistividad eléctrica por corriente directa para detectar y delimitar penachos contaminantes en un medio rocoso cristalino.

Critical Zone Exploration in the Tropics: Clues from small experimental watersheds in South Cameroon and South India

NASA Astrophysics Data System (ADS)

Braun, J.-J.; Riotte, J.; Audry, S.; Boeglin, J. L.; Descloitres, M.; Deschamps, P.; Maréchal, J. C.; Viers, J.; Ndam, J.-R.; Sekhar, M.

2009-04-01

Critical Zone Exploration in the Tropics: Clues from small experimental watersheds in South Cameroon and South India J.-J. BRAUN1,2*, J. RIOTTE1,2, S. AUDRY2, J. L. BOEGLIN2, M. DESCLOITRES3, P. DESCHAMPS4, J. C. MARÉCHAL1,2, J. VIERS2, J.-R. NDAM5, M. SEKHAR6, B. DUPRÉ2 1IFCWS, Indian Institute of Science, 560012 Bangalore, India. (*Correspondence: braun@civil.iisc.ernet.in) 2LMTG, Univ. Toulouse, CNRS IRD OMP, 14, avenue E. Belin, F-31400 Toulouse, France 3LTHE, Univ. Grenoble, CNRS, IRD, INPG, BP53, F-38041 Grenoble, Cedex 09, France 4CEREGE, Univ. Aix-Marseille, CNRS, IRD, Europôle Méditerranéen de l'Arbois, BP80, 13545 Aix en Provence, France. 5Université de Yaoundé I, Faculté des Sciences, Département des Sciences de la Terre, BP80, 13545 Yaoundé, Cameroun. 6Deprtment of Civil Engineering, Indian Institute of Science, 560012 Bangalore, India Understanding the relative controls of forcing factors on the silicate chemical weathering rates and the associated atmospheric CO2 consumption is usually assessed through investigations based on small to medium granito-gneissic watersheds from 1 to100 km2 located in different climatic and tectonic settings. In addition to climate, the importance of the thickness and nature of the blanket of loose and transportable weathered material, namely regolith, which overlies the intact bedrocks, was also recently invoked, especially in tropical environment. We have conducted an integrated approach of the Critical Zone in two pristine forested small watersheds located in Cameroon and India. Both watersheds have developed on granito-gneissic bedrocks of stable Precambrian shields. Our approach is directed at (i) understanding the bio-geochemical, hydro-geological and hydrological processes and (ii) assessing the long-term and contemporary chemical weathering rates. The Nsimi watershed, South Cameroon, has been the first to be monitored since 1994. It belongs to the Nyong River basin and has a humid tropical climate. It is characterized by a deep mature lateritic mantle and mean annual rainfall of 1600 mm. The second watershed, under investigation since 2003, is located at Mule Hole, South India. It belongs to the sub-humid zone of the climatic gradient of the Kabini River basin in the rain shadow of the Western Ghâts. It is characterized by an immature thick regolith and mean annual rainfall of 1100 mm. In both watersheds, the water balance was calculated from on time-series of hydrological and climatic data and then modelled for lean/normal/high rainfall years. The contemporary chemical weathering rates were established by coupling the water balance with geochemical time-series in groundwater, stream water and rainfall. The degree of weathering and the thickness of the regolith were achieved by combining investigations of geophysics (electrical resistivity logging and tomography), mineralogy, and bulk chemical analyses. This allowed us to assess the long-term chemical weathering mass balance at the watershed scale. In the Nsimi watershed, the contemporary chemical weathering rate, even though low (2.8 mm/kyr), predominates over the mechanical weathering rate (1.9 mm/kyr). Compared to the Rio Icacos watershed, the most studied tropical site, the chemical weathering fluxes of silica and sodium in the stream are 16 and 40 times lower, respectively. This is not only related to the protective role of the regolith, thick in both cases, but also to differences in the hydrological functioning. The carbon transfer occurs primarily in an organic form and essentially as colloids produced by the slow biodegradation of the swamp organic matter. These organic colloids contribute significantly to the mobilization and transfer of Fe, Al, Zr, Ti and Th in the uppermost first meter of the swamp regolith. In the Mule Hole watershed, the contemporary mechanical weathering rate (25 mm/kyr), predominates over the chemical weathering rate estimated for both stream (0.3 mm/kyr) and groundwater (3.0 mm/kyr). This difference is due to the disconnection of groundwater and stream during the monitored period of time. The contemporary denudation rate is then 28 mm/kyr, twice the one integrated over the last 100 kyr estimated with 10Be with the streambed sand. The immature, relatively thick regolith has a great potential to produce alkalinity by chemical weathering. Depending on the runoff and therefore climate variability with a more humid gradient (i. e. intensification of the monsoon), the production of alkalinity would increase and consequently increase the atmospheric CO2 consumption. This study has important signification in terms of quantification of the amount of weathered material at small watershed scale and hence of the assessment of the impact of silicate chemical weathering on atmospheric CO2 consumption. The hydrological functioning may then constitute a critical parameter for carbon cycle modelling. This study also stresses the need to have accurate monitoring at the watershed scale in a context of changing climate and to maintain such observatories for decades. Braun, J.-J. et al. (2008) Regolith mass balance inferred from combined mineralogical, geochemical and geophysical studies: Mule Hole gneissic watershed, South India. Geochimica et Cosmochimica Acta doi: 10.1016/j.gca.2008.11.013 Braun, J. J. (2005) Present weathering rates in a humid tropical watershed: Nsimi, South Cameroon. Geochimica et Cosmochimica Acta 69, 357-387. Maréchal, J.-C. et al. (2009) Indirect and direct recharges in a tropical forested watershed: Mule Hole, India. Journal of Hydrology 364, 272-284.

Surficial geology and geomorphology of Potter County, Pennsylvania

USGS Publications Warehouse

Denny, C.S.

1956-01-01

Potter County is located in the Appalachian Plateaus of north-central Pennsylvania and contains the headwaters of the Genesee River, the Allegheny River, and the Susquehanna River. Drift of Wisconsin age covers the northeastern part of the county. This study includes a detailed survev of the surficial deposits of the Genesee quadrangle in north-central Potter County and a reconnaissance of the remainder of the county; a soil survey and a botanical survey were carried on concurrently. The region is a deeply dissected plateau having extensive areas of steeply sloping land separated by narrow ridges and valleys; there is very little level land. Near the junction of the three watersheds the uplands rise to altitudes of more than 2,500 feet. The maximum relief in the Susquehanna drainage is more than 1,500 feet; in the Genesee and Allegheny drainage it. is about 800 feet. Valley walls are steep (15° to 30°), and the uplands have gentle slopes (0.5° to 10°). The drainage pattern is trellised. The climate is continental. Temperatures range from about -30° F. to more than 100° F. The average annual precipitation ranges approximately from 34 to 42 inches. Floods may occur at any season of the year. The large volumes of water from rain or melting snow carried by small streams come from springs. There is little precise data on frost in the ground, but it is probable that the ground seldom freezes in forested areas. The soils of Potter County have relatively immature profiles with poorly developed horizons that commonly have many characteristics inherited from their parent materials. At the great soil group level, the zonal soils are divided into Podzol soils and Brown Podzolic soils. Many soils have a high silt content in the upper part of the profile, apparently derived (at least partly) from a mantle of eolian silt. Mos~ of Potter County is covered by second-growth forests consisting of 40- to 60-year-old hardwood stands. The present forests growing on slopes and summits are composed approximately of 25 species of trees. The northern hardwood region includes most of the county, with an oak-forest region near the borders, principally along its southern margin. Potter County is underlain by sandstone, siltstone, shale, conglomerate, and minor amounts of coal and calcareous rock that range in age from Late Devonian to Pennsylvanian. These rocks form broad open folds that strike northeast. South of the border of the Wisconsin drift, and possibly at two localities inside the drift border, are scattered remnants of ancient soils (here called paleosol), that were formed in preWisconsin time-probably during the Sangamon interglacial stage. This paleosol ranges in texture from clay loam to silt loam, ranges in color from yellowish red to red, includes a few percent to more than 25 percent of rock fragments, and apparently contains a small percentage of gibbsite and varying amounts of kaolinite. Known thicknesses range from 1 to 33 feet. Paleosol was developed on diverse kinds of parent material, such as till, stratified drift, colluvium, and residuum, at altitudes ranging from a few hundred to 2,400 feet. The climatic conditions under which the paleosol formed are uncertain; however, these ancient soils may record an episode of subtropical climatic conditions during which lateritic soils were formed. Perhaps these soils are analogous to the Red-Yellow Podzolic soils of southeastern United States. Except for one possible remnant, no pre-Wisconsin drift has been recognized in Potter County. The Wisconsin glacial deposits of Potter County belong to either the Iowan or Tazewell substages and are dominantly till with minor amounts of glaciofluvial deposits. Erratics of igneous or metamorphic rock comprise less than 0.1 percent of the total number of rock fragments. The till is slightly weathered to depths ranging from 3 to about 12 feet. The drift border is indefinite and has been drawn at the southern limit of erratics or well-rounded or striated pebbles and is only locally marked by a terminal moraine or by a distinct change in the surficial deposits. The drift border is relatively straight and crosses the Genesee quadrangle in a northwesterly direction with little regard for the major topographic features, thus suggesting that the Wisconsin ice sheet had a relatively straight and steep front. Over most of the unglaciated part of Potter County, the bedrock is concealed beneath rubble that probably was formed during the Iowan or Tazewell substage, almost contemporaneously with the adjacent drift. In general, the rubble is thickest and most extensive within about 10 miles of the drift border, becoming thinner and less continuous farther away. The apparent parallelism between a belt of thick periglacial deposits and the drift border suggests that the deposits result from climatic factors in operation while the Wisconsin ice sheet was nearby. Ancient soil structures or patterned ground occur at, or near, the surface of both the periglacial deposits and the adjacent drift. These ancient soil structures are so similar to modern forms in arctic or alpine environments that they are considered to be the result of vigorous frost action. Many of the structures are believed to be a result of down-slope movement of debris by solifluction, facilitated by a frozen subsoil as much as 10 feet deep. Perennially frozen ground may have been present, but this is not a prerequisite. The periglacial deposits underlie long smooth slopes that extend from ridge crest to valley bottom. Flood plains are absent near the headwaters of many streams, the valley walls forming a V-shaped profile. While frost action was in progress, forests probably were restricted to flood plains, lower slopes, and scattered upland areas. Large parts of the upland were bare or partly covered by tundra vegetation; elsewhere, there were scattered trees but no dense forest. 1 2 SURFICIAL GEOLOGY AND GEOMORPHOLOGY OF POTTER COUNTY, PENNSYLVANIA Recent alluvium and alluvial fans include sand and sandy loams, 1 to 3 feet thick, that overlie gravel. The alluvium contains organic matter and lenses of finer materials. Thickness ranges from a few to more than 100 feet. Along the principal streams the alluvium probably overlies Pleistocene deposits. Most of the alluvial fans are composed of unstratified rubbly, pebbly, cobbly. or bouldery sandy loams to silty clay loams with local lenses of stratified sand and gravel. The alluvial fans mapped in the Genesee quadrangle probably include both Wisconsin stage and Recent deposits. The summits of the A.ppalachian Plateaus in north-central Pennsylvania have long been recognized as the remnants or traces of one or more peneplains. To test this hypothesis, a restored contour map was prepared to show the configuration of a supposed peneplain on the assumption that the plateau tops are remnants of such an old erosion surface. The restored contours delineate a surface that corresponds roughly to rock structure. In general, the uplands slope parallel to the dip of the bedrock. The major streams, such as the West Branch Susquehanna River, cross the ridges and valleys of the restored surface in such a way that it is difficult to suppose that the restored surface was ever graded to these streams. On the contrary, it is probable that the restored surface never existed and that the plateau tops are structurally controlled surfaces held up by sandstone and conglomerate beds in the Pottsville and Pocono formations. The plateau tops may have been lowered by erosion as much as 200 feet during the Pleistocene-in other words, after the major streams were incised. If this portion of the Appalachian Plateaus was ever reduced to a peneplain, such a hypothetical surface must have lain many hundreds of feet above the uplands of the present day. The only alternative that might involve peneplanation is the improbable hypothesis that the plateau tops are remnants of a slightly deformed peneplain and that the peneplain was folded along the axes of the Appalachian orogeny. This remote possibility is not supported by any known evidence. The geomorphic analysis yields no new data on the origin of the cross-axial drainage. Regardless of whether the plateaus are peneplain remnants or are structurally controlled surfaces, the beginning of the major southeastward-flowing streams long antedates the existing landscape. The geomorphic history of Potter County begins with an assumed long interval of erosion during the Mesozoic and early Cenozoic eras, for which no record remains in this area. The southeast master drainage was established by the latter part of the Tertiary period (perhaps at a much earlier date), probably as the result of the northwestward migration of the Atlanticinterior divide. In late Pliocene(?) time, areas adjacent to parts of the West Branch Susquehanna River-and probably elsewhere-had a moderate relief ranging from 300 to 700 feet. Some segments of the West Branch meandered across a broad valley that lay about 900 feet above the present streams. The landscape probably was covered by deep residual soils, perhaps by saprolite. The early Pleistocene history of Potter County is essentially unknown. No deposits of the Kansan stage are known except for a possible trace of pre-Illinoian drift on the uplands in central Potter County (Ayers Hill quadrangle). Some deposits in central and eastern Pennsylvania may be of Kansan age. It is probable that the assumed Aftonian regolith was removed by mass movements and other processes during the Kansan stage, thus resulting in a lowering of the plateau tops by as much as 10 feet. By the close of the Yarmouth(?) interglacial stage the major streams were incised to essentially their present depths. The climates of the Yarmouth interglacial stage probably produced deep residual soils over the landscape, parts of which may still be preserved in the paleosol remnants of the present day. No Illinoian drift is known in Potter County, but drift assigned to this stage occurs in areas to the northwest and to the southeast. Some valleys, such as Kettle Creek valley, were filled with sand and gravel alluvium to depths of as much as 150 feet above their present flood plains. It is assumed that the Yarmouth residual soils were removed by mass movements and other processes induced by a periglacial climate, thus lowering the plateau tops by as much as 10 feet. During the Sangamon interglacial stage, deep (10-to-20 foot) residual soils or paleosol were developed in Potter County and probably throughout much of Pennsylvania, perhaps as a result of lateritic weathering in a subtropical climate. It is possible that the paleosol was largely removed by mass movements and by running water during late Sangamon time. During either the Iowan or Tazewell substages of the Wisconsin (perhaps the Iowan), the ice sheet advanced into the northeastern part of Potter County. The drift is similar to the Olean drift (local usage). The paleosol was almost completely removed by mass movements and other processes induced· by a periglacial climate, prior to drift deposition. This removal probably resulted in a lowering of the plateau tops by as much as 10 feet since Sangamon time. Nearly contemporaneously with drift deposition, the periglacial deposits were formed by frost heaving, solifluction, and fluvial transport in areas outside the drift border. Soil structures or patterned ground were developed on both the drift and the periglacial deposits. It is probable that the forests in the periglacial area were greatly restricted and that large areas on the uplands were essentially treeless. Little is known about the history of Potter County in postOlean time. Presumably, forests completely covered the county by the onset of the next substage, during which the Binghamton drift of MacClintock and Apfel was deposited. This drift also is found in southern New York State. The formation of the alluvium and alluvial fans probably began in the Tazewell substage and continued during the Recent epoch. Since these deposits were formed there has been very little dissection. There is little, if any, difference between soils developed on periglacial deposits and soils developed on drift. The roots of fallen trees have disturbed the soil horizons, and it is unlikely that the existing soil profiles are more than 500 years old. The forested landscape of Potter County has a distinctive microrelief ranging from a few inches to a few feet of mounds and pits produced by the roots of fallen trees. Most mounds and pits range from 10 to 20 feet in length and from 6 to 15 feet in width. On level land, many mounds are oriented with their long axes trending northward, and in some areas the orientation is random. On slopes, the mounds are oriented with their long axes at right angles to the maximum slope as a result of trees falling downslope. The toppling of trees increases the permeability of surficial deposits and mixes and destroys the soil horizons. The microrelief is a factor in forest development. The toppling of trees on slopes is a significant agent of slope erosion. The process loosens, breaks up, or overturns the upper 2 to 3 feet of the forest soil, and it tends to make the surficial layer more stony and to produce features resembling soil structures.

Geology and ground-water resources of the island of Oahu, Hawaii

USGS Publications Warehouse

Stearns, Harold T.; Vaksvik, Knute N.

1935-01-01

Oahu, one of the islands of the Hawaiian group, lies in the Mid-Pacific 2,100 miles southwest of San Francisco. The principal city is Honolulu. The Koolau Range makes up the eastern part of the island, and the Waianae Range the western part. Both are extinct basaltic volcanoes deeply dissected by erosion. The Koolau Volcano was the later to become extinct. The Waianae Range is made up of three groups of lavas erupted in Tertiary and possibly in early Pleistocene time. The exposed part of the older lava is nearly 2,000 feet thick and consists largely of thin-bedded pahoehoe. It is separated in most places from the middle lavas by an angular unconformity and talus breccia and in a few places by an erosional unconformity. The middle basalts are about 2,000 feet thick and closely resemble the lower ones except that they contain more aa. The upper lavas reach a thickness of about 2,300 feet and are mostly massive aa flows. The last eruptions produced large cinder cones and some nephelite basalts. The Waianae Volcano, like other Hawaiian volcanoes, produced only small amounts of ash, and the lavas were largely extruded from fissures a few feet wide, now occupied by dikes. The center of activity was near Kolekole Pass, at the head of Lualualei Valley.The Koolau Volcano is made up of two groups of lavas extruded in Tertiary and early Pleistocene (?) time. The older group, the Kailua volcanic series, is greatly altered by hydrothermal action and was extruded from fissures near Lanikai. The flows of the younger group, the Koolau volcanic series, were extruded from fissures about a mile south of the Kailua rift and have an exposed thickness of about 3,000 feet. The Koolau Volcano produced even less ash than the Waianae Volcano, and its flows are thin-bedded pahoehoe and aa. The eruptive center of the Koolau Volcano lies between Kaneohe and Waimanalo. Great amounts of both the Waianae and Koolau Ranges were removed by fluvial and marine erosion during the Pleistocene. The master streams are characterized by deep amphitheater-headed valleys. After this erosion cycle the island was submerged more than 1,200 feet, and these great valleys were drowned and alluviated. Besides this submergence, several strand lines, preserved up to 100 feet above present sea level occur, which may be due to world-wide changes in sea level in response to the withdrawal and restoration of water concurrent with the advances and recessions of the polar ice caps and to accompanying changes in the ocean floor. During this time of shifting ocean levels spasmodic eruptions occurred on the southeast end of the Koolau Range, producing numerous lava flows and tuff cones, most of which are nephelite basalt. The last of these eruptions occurred in Recent time. A description of the climate, rates of run-off, and results of experiments to determine evaporation and transpiration in the areas of high rainfall are given. It was found that the consumptive use decreases materially and becomes a very small percentage of the rainfall in the areas of high precipitation. The lava rocks of the island are very permeable and, because of a rainfall reaching a maximum of 300 inches a year, carry large amounts of ground water, confined and unconfined, basal and perched. The basal ground water floats on salt water because of its lower specific gravity. Consequently for each foot the water table stands above sea level, salt water lies about 42 feet below sea level, in accordance with the sea along the coast as basal ground water. In most places the lava rocks along the shore are overlain by an impermeable or nearly impermeable caprock consisting of submerged lateritic soils and marine noncalcareous sediments. These deposits retard the escape of basal ground water into the sea and give rise to artesian water, but unlike most other artesian systems, this one has no lower restraining formation. The artesian water is the principal source of domestic, municipal, and irrigation supplies. The average annual quantity pumped for the period 1928 to 1933 amounted to about 105,000,000,000 gallons, nearly 90 percent of which came from Koolau hasalt and the remainder from Waianae basalt. There are ten artesian areas in the Koolau Range and two in the Waianae Range. Hydraulic gradients in these basins were found to range from 1.2 to 3 feet to the mile. Because of these extremely flat gradients and the high permeability of the aquifers it is possible to reverse the hydraulic gradients by draft and make the water flow from one artesian area to another. The artesian water levels fluctuate in response to seasonal variations in draft and recharge and in a lesser way to tidal, barometric, and seismic pressures. The water, as shown by chemical analysis, is of excellent quality except where it is contaminated with sea water. Methods have been devised for freshening wells that have gone salty, for detecting leaks, for sealing leaky and defective wells, and for recharging the artesian basins. Owing to the danger of the wells becoming brackish with increased draft, it is believed that further large developments will be more successful if shafts are sunk to sea level in the basalt as far inland as practicable, and tunnels are driven from the bottom of the shafts near the top of the saturated zone. Favorable places for such development exist in Honolulu.In addition to the basal water in the volcanic rocks, water is found in the recent gravel, beach, and dune deposits, and the emerged reef limestone. This water has been recovered by wells and tunnels, and there are favorable localities for developing additional water of this type. The island contains two types of basal springs—those like the Pearl Harbor Springs, which issue from basalt and are supplied by overflow and leakage from the artesian basin, and those which issue from the coastal-plain sediments and are mainly return irrigation water. The total quantity of basal ground water issuing as springs is estimated to be 100,000,000 gallons a day. Ground water occurs at high levels, confined by dikes and perched on tuff, alluvium, and soil beds. These structures give rise to innumerable high-level springs. In the Koolau Range 60 tunnels yield about 33,000,000 gallons daily, of which about 95 percent is obtained from tunnels penetrating the dike complex of the Koolau volcanic series, about 2 percent from tunnels entering post-Koolau ash or tuff deposits, and the remainder from tunnels whose geologic relations are not certainly known. The average daily yield of the tunnels that recover dike water is 2,330 gallons a foot, but the average daily yield of the tunnels in post-Koolau tuff is 450 gallons a foot, and that of the tunnels in alluvium or soil is only 23 gallons a foot. Owing largely to the much lower rainfall on the Waianac Range, its 35 tunnels (not including two new tunnels under construction) yield only about 2,400,000 gallons daily, about 94 percent of which is believed to be obtained from dike systems. The average daily yield of the tunnels in this range that are supplied by dike systems is 581 gallons a foot, as compared to 5 gallons a foot from tunnels in ash or tuff. An extensive tunnel system is proposed to develop a large supply of high-level water for Honolulu from the dike complex of the Koolau series, and high-level water can be recovered by tunnels at many other places. The average daily discharge of all high-level springs in the Koolau Range is about 58,000,000 gallons, of which about 94 percent comes from the Koolau dike complex and about 6 percent from post-Koolau volcanic rocks. The average daily discharge of all high-level springs in the Waianae Range is about 500,000 gallons of which about 81 percent issues from the dike complex.