Determination of Lead in Urine by Atomic Absorption Spectrophotometry1

PubMed Central

Selander, Stig; Cramé, Kim

1968-01-01

A method for the determination of lead in urine by means of atomic absorption spectrophotometry (AAS) is described. A combination of wet ashing and extraction with ammonium pyrrolidine dithiocarbamate into isobutylmethylketone was used. The sensitivity was about 0·02 μg./ml. for 1% absorption, and the detection limit was about 0·02 μg./ml. with an instrumental setting convenient for routine analyses of urines. Using the scale expansion technique, the detection limit was below 0·01 μg./ml., but it was found easier to determine urinary lead concentrations below 0·05 μg./ml. by concentrating the lead in the organic solvent by increasing the volume of urine or decreasing that of the solvent. The method was applied to fresh urines, stored urines, and to urines, obtained during treatment with chelating agents, of patients with lead poisoning. Urines with added inorganic lead were not used. The results agreed well with those obtained with a colorimetric dithizone extraction method (r = 0·989). The AAS method is somewhat more simple and allows the determination of smaller lead concentrations. PMID:5647975

Determination of Lead in Blood by Atomic Absorption Spectrophotometry1

PubMed Central

Selander, Stig; Cramér, Kim

1968-01-01

Lead in blood was determined by atomic absorption spectrophotometry, using a wet ashing procedure and a procedure in which the proteins were precipitated with trichloroacetic acid. In both methods the lead was extracted into isobutylmethylketone before measurement, using ammonium pyrrolidine dithiocarbamate as chelator. The simpler precipitation procedure was shown to give results identical with those obtained with the ashing technique. In addition, blood specimens were examined by the precipitation method and by spectral analysis, which method includes wet ashing of the samples, with good agreement. All analyses were done on blood samples from `normal' persons or from lead-exposed workers, and no additions of inorganic lead were made. The relatively simple protein precipitation technique gave accurate results and is suitable for the large-scale control of lead-exposed workers. PMID:5663425

24 CFR 35.1325 - Abatement.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... accordance with § 35.1340. If encapsulation or enclosure is used as a method of abatement, ongoing lead-based...

24 CFR 35.1325 - Abatement.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... accordance with § 35.1340. If encapsulation or enclosure is used as a method of abatement, ongoing lead-based...

24 CFR 35.1325 - Abatement.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... accordance with § 35.1340. If encapsulation or enclosure is used as a method of abatement, ongoing lead-based...

24 CFR 35.1325 - Abatement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... accordance with § 35.1340. If encapsulation or enclosure is used as a method of abatement, ongoing lead-based...

24 CFR 35.1325 - Abatement.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... accordance with § 35.1340. If encapsulation or enclosure is used as a method of abatement, ongoing lead-based...

Method of manufacturing lead electrodes for storage cells

DOEpatents

Jonville, P.; Stoehr, H.; Beccu, K.D.

1975-09-23

A method of manufacturing electrodes for lead storage batteries is described. Molten lead or lead alloy is deposited on a felt of glass fibers by spraying in a molten state to fill the space between the fibers of the felt to form an electrically conductive zone defining electrode contacts. A mass of powdered lead-based material is introduced into the felt by filtration for subsequently producing an active electrode mass by at least one electrochemical transformation. The felt is then cut into individual electrodes. (auth)

The effect of different propolis harvest methods on its lead contents determined by ET AAS and UV-visS.

PubMed

Sales, A; Alvarez, A; Areal, M Rodriguez; Maldonado, L; Marchisio, P; Rodríguez, M; Bedascarrasbure, E

2006-10-11

Argentinean propolis is exported to different countries, specially Japan. The market demands propolis quality control according to international standards. The analytical determination of some metals, as lead in food, is very important for their high toxicity even in low concentrations and because of their harmful effects on health. Flavonoids, the main bioactive compounds of propolis, tend to chelate metals as lead, which becomes one of the main polluting agents of propolis. The lead found in propolis may come from the atmosphere or it may be incorporated in the harvest, extraction and processing methods. The aim of this work is to evaluate lead level on Argentinean propolis determined by electrothermal atomic absorption spectrometry (ET AAS) and UV-vis spectrophotometry (UV-visS) methods, as well as the effect of harvest methods on those contents. A randomized test with three different treatments of collection was made to evaluate the effect of harvest methods. These procedures were: separating wedges (traditional), netting plastic meshes and stamping out plastic meshes. By means of the analysis of variance technique for multiple comparisons (ANOVA) it was possible to conclude that there are significant differences between scraped and mesh methods (stamped out and mosquito netting meshes). The results obtained in the present test would allow us to conclude that mesh methods are more advisable than scraped ones in order to obtain innocuous and safe propolis with minor lead contents. A statistical comparison of lead determination by both, ET AAS and UV-visS methods, demonstrated that there is not a significant difference in the results achieved with the two analytical techniques employed.

Lead Apron Inspection Using Infrared Light: A Model Validation Study.

PubMed

McKenney, Sarah E; Otero, Hansel J; Fricke, Stanley T

2018-02-01

To evaluate defect detection in radiation protective apparel, typically called lead aprons, using infrared (IR) thermal imaging. The use of IR lighting eliminates the need for access to x-ray-emitting equipment and radiation dose to the inspector. The performance of radiation workers was prospectively assessed using both a tactile inspection and the IR inspection with a lead apron phantom over a 2-month period. The phantom was a modified lead apron with a series of nine holes of increasing diameter ranging from 2 to 35 mm in accordance with typical rejection criteria. Using the tactile method, a radiation worker would feel for the defects in the lead apron. For the IR inspection, a 250-W IR light source was used to illuminate the lead apron phantom; an IR camera detected the transmitted radiation. The radiation workers evaluated two stills from the IR camera. From the 31 participants inspecting the lead apron phantom with the tactile method, only 2 participants (6%) correctly discovered all 9 holes and 1 participant reported a defect that was not there; 10 of the 20 participants (50%) correctly identified all 9 holes using the IR method. Using a weighted average, 5.4 defects were detected with the tactile method and 7.5 defects were detected with the IR method. IR light can penetrate an apron's protective outer fabric and illuminate defects below the current standard rejection size criteria. The IR method improves defect detectability as compared with the tactile method. Copyright © 2017 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Determination of lead equivalent values according to IEC 61331-1:2014—Report and short guidelines for testing laboratories

NASA Astrophysics Data System (ADS)

Büermann, L.

2016-09-01

Materials used for the production of protective devices against diagnostic medical X-radiation described in the international standard IEC 61331-3 need to be specified in terms of their lead attenuation equivalent thickness according to the methods described in IEC 61331-1. In May 2014 the IEC published the second edition of these standards which contain improved methods for the determination of attenuation ratios and the corresponding lead attenuation equivalent thicknesses of lead-reduced or lead-free materials. These methods include the measurement of scattered photons behind the protective material which were hitherto neglected but are becoming more important because of the increasing use of lead-reduced or even lead-free materials. They can offer the same protective effect but are up to 20% lighter and also easier to dispose of. The new method is based on attenuation ratios measured with the so-called ``inverse broad beam condition''. Since the corresponding measurement procedure is new and in some respects more complex than the methods used in the past, it was regarded as being helpful to have a description of how such measurements can reliably be performed. This technical report describes in detail the attenuation ratio measurements and corresponding procedures for the lead equivalent determinations of sample materials using the method with the inverse broad beam condition as carried out at the Physikalisch-Technische Bundesanstalt (PTB). PTB still offers material testing and certification for the German responsible notified body. In addition to the description of the measurements at PTB, a short technical guide is provided for testing laboratories which intend to establish this kind of protective material certification. The guide includes technical recommendations for the testing equipment like X-ray facilities, reference lead sheets and radiation detectors; special procedures for the determination of the lead attenuation equivalent thickness; their uncertainties and the necessary contents of the test certificate.

Superconducting transition edge sensors and methods for design and manufacture thereof

NASA Technical Reports Server (NTRS)

Sadleir, John E. (Inventor)

2013-01-01

Methods for forming sensors using transition edge sensors (TES) and sensors therefrom are described. The method includes forming a plurality of sensor arrays includes at least one TES device. The TES device includes a TES device body, a first superconducting lead contacting a first portion of the TES device body, and a second superconducting lead contacting of a second portion of the TES device body, where the first and second superconducting leads separated on the TES device body by a lead spacing. The lead spacing can be selected to be different for at least two of the plurality of sensor arrays. The method also includes determining a transition temperature for each of the plurality of sensor arrays and generating a signal responsive to detecting a change in the electrical characteristics of one of the plurality of sensor arrays meeting a transition temperature criterion.

A lead isotope distribution study in swine tissue using ICP-MS

USGS Publications Warehouse

May, T.W.; Wiedmeyer, Ray H.; Brown, L.D.; Casteel, S.W.

1999-01-01

In the United States lead is an ubiquitous environmental pollutant that is a serious human health hazard, especially for women of childbearing age, developing fetuses, and young children. Information concerning the uptake and distribution of lead to maternal and fetal tissues during pregnancy is poorly documented. A study was designed using domestic swine and lead isotope enrichment methodology to focus on maternal absorption and distribution of lead into bone and soft tissues, including the fetal compartment, under varying conditions of oral lead exposure and during altered physiological states (pregnant vs unbred). Total lead levels and Pb207/Pb206 ratios in bone (femur and vertebra), blood, and soft tissues (liver, kidney, brain) were determined by ICP-MS. Lead in fetal tissues derived from maternal bone could be differentiated from that derived from exogenous dosing. Unbred swine absorbed much less lead than pregnant females receiving the same dose. The accuracy and precision of ICP-MS at the instrumental level and for the entire method (sample collection, digestion, and analysis) were evaluated for both Pb207/Pb206 ratios and total lead. Several changes were suggested in method design to improve both instrumental and total method precision.

Evaluation of four sampling methods for determining exposure of children to lead-contaminated household dust

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sterling, D.A.; Roegner, K.C.; Lewis, R.D.

Childhood exposure to lead has been demonstrated to result in health effects and lead-contaminated household dust is a primary exposure source. There is a need to establish reliable methods for sampling surfaces to determine levels of lead contamination. Three vacuums (HVS3, GS80, and MVM) and one wipe method were evaluated for the collection of household floor dust under field sampling conditions within a Superfund site and demographically similar control area. Side-by-side floor samples were taken from three locations within 41 randomly selected households between August and September 1995: a child's bedroom, primary play area, and primary entrance. Analysis was performedmore » to assess the relative collection performance of each sampler, spatial distribution of lead within a household, and correlation of lead loading with observed blood lead level, and to determine if discrete or composites samples were more predictive of blood lead levels. Approximately 90% of the floor surfaces were carpeted. The rank order of sampling methods from greatest to lowest collection efficiency was HVS3 > G80 > wipe > MVM. The HVS3 had the highest level of precision (CV = 0.05), with the GS80 and wipe precisions 0.48 and 0.053, respectively.« less

Reducing bone lead content by chelation treatment in chronic lead poisoning: an in vivo X-ray fluorescence and bone biopsy study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Batuman, V.; Wedeen, R.P.; Bogden, J.D.

1989-02-01

A stained-glass artist with longstanding exposure to lead presented with neuropsychiatric symptoms. He was evaluated before and after chelation treatment by the CaNa2 EDTA lead mobilization test, iliac crest bone lead measurement, and in vivo tibial X-ray fluorescence (XRF). The three methods showed a progressive fall in body lead stores during chelation therapy in association with improvement in symptoms and a fall in blood lead and zinc protoporphyrin levels. In vivo tibial XRF is a safe, rapid, and noninvasive technique for detecting excessive body lead burdens. XRF measurement of bone lead content is a practical method for monitoring the efficacymore » of therapy as well as for establishing the diagnosis.« less

Recovering lead from cupel waste generated in gold analysis by Pb-Fire assay.

PubMed

Cerceau, Cristiane Isaac; Carvalho, Cornélio de Freitas; Rabelo, Ana Carolina Silveira; Dos Santos, Cláudio Gouvea; Gonçalves, Sabrina Mayra Dias; Varejão, Eduardo Vinícius Vieira

2016-12-01

Because of its precision and accuracy, Pb-Fire assay is the most employed method for gold analysis in geological materials. At the second stage of the method, namely cupellation, lead is oxidized to PbO which is absorbed by the cupel, leading to metallic gold as a tiny bend at the bottom of the recipient. After cupellation, cupel becomes highly contaminated with lead, making its disposal a serious risk of environmental contamination. In the present work, a leaching process for removing lead from cupel waste is proposed, which allowed for removing 96% of PbO by weight. After a precipitation step, 92.0% of lead was recovered from leachates in the form of PbSO 4 . Lead in the solid wastes left by the extraction was above the limit established by Brazilian legislation and these were classified as non-hazardous. Finally, secondary effluents generated after the precipitation step presented lead content more than twenty times lower than that of leachates from cupel waste. Tons of cupel waste are annually generated from gold analysis by Pb-Fire assay. Thus, the proposed method can contribute to prevent the discharge of high amounts of lead into the environment. Also, recovery of lead can help to partially meet the industrial demand for lead compounds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Method for a Leading Edge Slat on a Wing of an Aircraft

NASA Technical Reports Server (NTRS)

Pitt, Dale M. (Inventor); Eckstein, Nicholas Stephen (Inventor)

2016-01-01

A method for managing a flight control surface system. A leading edge device is moved on a leading edge from an undeployed position to a deployed position. The leading edge device has an outer surface, an inner surface, and a deformable fairing attached to the leading edge device such that the deformable fairing covers at least a portion of the inner surface. The deformable fairing changes from a deformed shape to an original shape when the leading edge device is moved to the deployed position. The leading edge device is then moved from the deployed position to the undeployed position, wherein the deformable fairing changes from the original shape to the deformed shape.

An efficient method for computation of the manipulator inertia matrix

NASA Technical Reports Server (NTRS)

Fijany, Amir; Bejczy, Antal K.

1989-01-01

An efficient method of computation of the manipulator inertia matrix is presented. Using spatial notations, the method leads to the definition of the composite rigid-body spatial inertia, which is a spatial representation of the notion of augmented body. The previously proposed methods, the physical interpretations leading to their derivation, and their redundancies are analyzed. The proposed method achieves a greater efficiency by eliminating the redundancy in the intrinsic equations as well as by a better choice of coordinate frame for their projection. In this case, removing the redundancy leads to greater efficiency of the computation in both serial and parallel senses.

Lead detection in living plant tissue using a new histochemical method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glater, R.A.B.; Hernandez, L. Jr.

1972-06-01

A quick, simple method for identifying and distinguishing lead from other heavy metals in living plants has been developed using sodium rhodizonate (C/sub 6/O/sub 6/Na/sub 2/) which forms a scarlet precipitate with lead at approximately pH 2.8. Hand sections of plant tissues are treated with rhodizonate reagent, buffered, and examined microscopically. Very little time and/or effect is required for this method. Those cells and tissues contaminated with lead turn scarlet - color intensity being directly related to concentration. Lead may be detected in quite low concentrations and, most importantly, may be observed in situ; its entry and movement through themore » plant can thus be followed. In an area of moderate traffic of Downey, California (Southeast Los Angeles), lead was found abundantly on leaves as well as on and in roots of garden-grown lettuce; origin of this lead is presumed to be from car exhausts.« less

Preparing ultrafine PbS powders from the scrap lead-acid battery by sulfurization and inert gas condensation

NASA Astrophysics Data System (ADS)

Xia, Huipeng; Zhan, Lu; Xie, Bing

2017-02-01

A novel method for preparing ultrafine PbS powders involving sulfurization combined with inert gas condensation is developed in this paper, which is applicable to recycle Pb from lead paste of spent lead-acid batteries. Initially, the effects of the evaporation and condensation temperature, the inert gas pressure, the condensation distance and substrate on the morphology of as-obtained PbS ultrafine particles are intensively investigated using sulfur powders and lead particles as reagents. Highly dispersed and homogeneous PbS nanoparticles can be prepared under the optimized conditions which are 1223 K heating temperature, 573 K condensation temperature, 100 Pa inert gas pressure and 60 cm condensation distance. Furthermore, this method is successfully applied to recycle Pb from the lead paste of spent lead acid battery to prepare PbS ultrafine powders. This work does not only provide the theoretical fundamental for PbS preparation, but also provides a novel and efficient method for recycling spent lead-acid battery with high added-value products.

The effect of a lignosulphate type additive on the lead—acid battery positive plate reactions

NASA Astrophysics Data System (ADS)

Ovuru, S. E.; Harrison, J. A.

The electrochemical formation of lead dioxide has been investigated at a lead electrode in a 5 M sulphuric acid solution, and in the presence of phosphoric acid and lignosulphate-type additive. The formation of lead dioxide from lead sulphate, and the reverse reaction, have been investigated by the linear potential sweep method, by an impedance method in which the impedance was measured at the end of each pulse during a potential pulse train, and by a charging curve method in which the current and charge was measured during a similar potential pulse train. The charge measurements prove that the main effect of the additive is to decrease the accompanying oxygen evolution reaction. The impedance measurements, however, show that the additive has a small but significant effect on the structure of the solid lead sulphate and lead dioxide layers.

Investigation of the Preservation Method within Environmental Protection Agency Method 200.8

EPA Science Inventory

Lead (Pb) is a trace metal that is closely regulated in drinking water systems because of its harmful toxicity. The U.S. Environmental Protection Agency (USEPA) issued the Lead and Copper Rule (LCR), which defines the action level for Lead as 0.015 mg/L. Researchers and drinking ...

2010 Lead (Pb) Air Monitoring Requirements & 2013 Method for Determination of Lead (Pb) in Total Suspended Particulate Matter Fact Sheets

EPA Pesticide Factsheets

This page contains a variety of fact sheets and other documents that are supplementary to the 2010 final revisions to lead (Pb) ambient air monitoring requirements and the 2013 final method for determination of Pb in total suspended particulate matter.

Development and validation of a novel, simple, and accurate spectrophotometric method for the determination of lead in human serum.

PubMed

Shayesteh, Tavakol Heidari; Khajavi, Farzad; Khosroshahi, Abolfazl Ghafuri; Mahjub, Reza

2016-01-01

The determination of blood lead levels is the most useful indicator of the determination of the amount of lead that is absorbed by the human body. Various methods, like atomic absorption spectroscopy (AAS), have already been used for the detection of lead in biological fluid, but most of these methods are based on complicated, expensive, and highly instructed instruments. In this study, a simple and accurate spectroscopic method for the determination of lead has been developed and applied for the investigation of lead concentration in biological samples. In this study, a silica gel column was used to extract lead and eliminate interfering agents in human serum samples. The column was washed with deionized water. The pH was adjusted to the value of 8.2 using phosphate buffer, and then tartrate and cyanide solutions were added as masking agents. The lead content was extracted into the organic phase containing dithizone as a complexion reagent and the dithizone-Pb(II) complex was formed and approved by visible spectrophotometry at 538 nm. The recovery was found to be 84.6 %. In order to validate the method, a calibration curve involving the use of various concentration levels was calculated and proven to be linear in the range of 0.01-1.5 μg/ml, with an R (2) regression coefficient of 0.9968 by statistical analysis of linear model validation. The largest error % values were found to be -5.80 and +11.6 % for intra-day and inter-day measurements, respectively. The largest RSD % values were calculated to be 6.54 and 12.32 % for intra-day and inter-day measurements, respectively. Further, the limit of detection (LOD) was calculated to be 0.002 μg/ml. The developed method was applied to determine the lead content in the human serum of voluntary miners, and it has been proven that there is no statistically significant difference between the data provided from this novel method and the data obtained from previously studied AAS.

Results of a greenhouse study investigating the phytoextraction of lead from contaminated soils obtained from the Sunflower Army Ammunition Plant, Desoto, Kansas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bader, D.F.; Behel, A.D.; Almond, R.A.

1998-08-01

This report describes the results of greenhouse studies conducted to determine if phytoextraction methods could be enhanced by increasing ionic lead`s solubility in water. Soil acidifiers and chelating agents were used to increase lead`s solubility in water. The study was conducted using lead contaminated soil from the Sunflower Army Ammunition Plant near Desoto, Kansas. These soils were shipped to the Tennessee Valley Authority`s Environmental Research Facility in Muscle Shoals, Alabama, where the study was conducted. The report concludes that phytoextraction methods may be enhanced by these techniques and that the risk of leaching lead out of the soil`s root zonemore » is minimal.« less

Method and Apparatus for a Leading Edge Slat on a Wing of an Aircraft

NASA Technical Reports Server (NTRS)

Pitt, Dale M. (Inventor); Eckstein, Nicholas Stephen (Inventor)

2013-01-01

A method and apparatus for managing a flight control surface system. A leading edge device is moved on a leading edge from an undeployed position to a deployed position. The leading edge device has an outer surface, an inner surface, and a deformable fairing attached to the leading edge device such that the deformable fairing covers at least a portion of the inner surface. The deformable fairing changes from a deformed shape to an original shape when the leading edge device is moved to the deployed position. The leading edge device is then moved from the deployed position to the undeployed position, wherein the deformable fairing changes from the original shape to the deformed shape.

Rapid and Highly Sensitive Detection of Lead Ions in Drinking Water Based on a Strip Immunosensor

PubMed Central

Kuang, Hua; Xing, Changrui; Hao, Changlong; Liu, Liqiang; Wang, Libing; Xu, Chuanlai

2013-01-01

In this study, we have first developed a rapid and sensitive strip immunosensor based on two heterogeneously-sized gold nanoparticles (Au NPs) probes for the detection of trace lead ions in drinking water. The sensitivity was 4-fold higher than that of the conventional LFA under the optimized conditions. The visual limit of detection (LOD) of the amplified method for qualitative detection lead ions was 2 ng/mL and the LOD for semi-quantitative detection could go down to 0.19 ng/mL using a scanning reader. The method suffered from no interference from other metal ions and could be used to detect trace lead ions in drinking water without sample enrichment. The recovery of the test samples ranged from 96% to 103%. As the detection method could be accomplished within 15 min, this method could be used as a potential tool for preliminary monitoring of lead contamination in drinking water. PMID:23539028

Levels of lead in foods from the first French total diet study on infants and toddlers.

PubMed

Guérin, Thierry; Le Calvez, Emilie; Zinck, Julie; Bemrah, Nawel; Sirot, Véronique; Leblanc, Jean-Charles; Chekri, Rachida; Hulin, Marion; Noël, Laurent

2017-12-15

Infants and toddlers are highly vulnerable to exposure to lead due to its higher absorption in small children than in adults. This study describes the optimisation and validation of a very sensitive method for the determination of low levels of lead in foods mostly consumed by infants and toddlers. This method, based on inductively coupled plasma-mass spectrometry with a programmable temperature cyclonic spray chamber, attained a limit of quantification (LOQ) of 0.6 or 0.9µgPbkg -1 for a liquid or a solid sample, that was improved by a factor 5.6-8.3 compared to the previous method (LOQ: 5µgkg -1 ). The analytical method was then applied to 291 food samples from the first French total diet study on infants and toddlers. Lead was detected in most samples at relatively low concentrations (range 0.0-16µgkg -1 ). The highest lead concentrations were mainly found in processed food products (e.g. products containing chocolate). Copyright © 2017 Elsevier Ltd. All rights reserved.

Lead in a Baltimore shipyard.

PubMed

Hall, Francis X

2006-12-01

The goal was to monitor the effectiveness of the Coast Guard Yard's lead program by comparing a shipyard period in 1991 to one in 2002-2003. Comparisons of airborne lead levels by paint removal techniques, airborne lead levels by welding techniques, and blood lead levels of workers were evaluated by chi2 analysis. Airborne lead levels in paint removal techniques decreased over time for all methods used. Airborne lead levels in welding techniques decreased over time for all methods used. Blood lead levels of the high-risk group revealed a 2-fold reduction (prevalence rate ratio = 8.3; 95% confidence interval, 3.7-18.6) and in the low-risk group revealed a 1.6-fold reduction (prevalence rate ratio = 6.2; 95% confidence interval, 0.86-44.7). The Coast Guard Yard runs an effective lead program that exceeds the national Healthy People 2010 goal for lead. The results validate the Coast Guard Yard's use of air-line respirators and lead-free paint on all vessels.

Recent Advances in the Clinical Management of Lead Poisoning.

PubMed

Kianoush, Sina; Sadeghi, Mahmood; Balali-Mood, Mahdi

2015-01-01

Lead poisoning is a historic universal disease. Acute or chronic lead exposure may cause reversible or even permanent damages in human beings. Environmental lead exposure is a global health concern in children. Occupational lead poisoning is still a health issue, particularly in developing countries. During the last decades, new methods and medications have been advocated for the prevention and treatment of lead poisoning. This review deals mainly with recent developments in the management of lead poisoning. Sources of lead exposure are introduced, and methods for the primary prevention of lead poisoning are discussed. Details for the screening of adults and children are also explained to serve as a practical guideline for the secondary prevention. Standard chelation therapy in different groups and up-to-date less toxic new medications for the treatment of lead poisoning are finally discussed. Our published clinical research on the therapeutic effects of garlic tablets in mild to moderate occupational lead poisoning will also be discussed.

Mapping sea ice leads with a coupled numeric/symbolic system

NASA Technical Reports Server (NTRS)

Key, J.; Schweiger, A. J.; Maslanik, J. A.

1990-01-01

A method is presented which facilitates the detection and delineation of leads with single-channel Landsat data by coupling numeric and symbolic procedures. The procedure consists of three steps: (1) using the dynamic threshold method, an image is mapped to a lead/no lead binary image; (2) the likelihood of fragments to be real leads is examined with a set of numeric rules; and (3) pairs of objects are examined geometrically and merged where possible. The processing ends when all fragments are merged and statistical characteristics are determined, and a map of valid lead objects are left which summarizes useful physical in the lead complexes. Direct implementation of domain knowledge and rapid prototyping are two benefits of the rule-based system. The approach is found to be more successfully applied to mid- and high-level processing, and the system can retrieve statistics about sea-ice leads as well as detect the leads.

AN EXPERIMENTAL EVALUATION OF THREE METHODS FOR INCREASING THE LEADING EDGE THICKNESS OF SUPERCAVITATING PROPELLERS.

DTIC Science & Technology

An experimental investigation of three methods of increasing the leading-edge thickness of supercavitating propeller sections was conducted. The...addition of a parabolic thickness to both the face and back of the section. Five supercavitating propeller models incorporating these three methods of

Investigation of Analytical Techniques for the Rapid Determination of the Moisture Content of NOL 130 Primer Mix and Lead Azide

DTIC Science & Technology

1986-05-01

the presence of NOL 130 6 Determination of moisture content of dextrinated lead azide 14 containing known amounts of water, by the Karl Fisher method...maLhiod, extraction mode 8 Determinatiov) of moisture content of special purpose and 16 dextrinated lead atide, containing known amounts of water by the...water in special purpose and dextrinated lead azides were determined by the method described in the experimen- tal section of this report, data shown

40 CFR 53.2 - General requirements for a reference method determination.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Manual methods—(1) Sulfur dioxide (SO 2 ) and lead. For measuring SO2 and lead, appendices A and G of part 50 of this chapter specify unique manual FRM for measuring these pollutants. Except as provided in § 53.16, other manual methods for SO2 and lead will not be considered for FRM determinations under this...

Low level lead exposure: history and discovery.

PubMed

Needleman, Herbert

2009-04-01

The history of lead toxicity spans 2 millennnia. With increasingly sensitive methods, deficits due to lead exposure have been demonstrated at lower and lower doses. Persuasive evidence suggests that no threshold for lead toxicity exists.

Random left censoring: a second look at bone lead concentration measurements

NASA Astrophysics Data System (ADS)

Popovic, M.; Nie, H.; Chettle, D. R.; McNeill, F. E.

2007-09-01

Bone lead concentrations measured in vivo by x-ray fluorescence (XRF) are subjected to left censoring due to limited precision of the technique at very low concentrations. In the analysis of bone lead measurements, inverse variance weighting (IVW) of measurements is commonly used to estimate the mean of a data set and its standard error. Student's t-test is used to compare the IVW means of two sets, testing the hypothesis that the two sets are from the same population. This analysis was undertaken to assess the adequacy of IVW in the analysis of bone lead measurements or to confirm the results of IVW using an independent approach. The rationale is provided for the use of methods of survival data analysis in the study of XRF bone lead measurements. The procedure is provided for bone lead data analysis using the Kaplan-Meier and Nelson-Aalen estimators. The methodology is also outlined for the rank tests that are used to determine whether two censored sets are from the same population. The methods are applied on six data sets acquired in epidemiological studies. The estimated parameters and test statistics were compared with the results of the IVW approach. It is concluded that the proposed methods of statistical analysis can provide valid inference about bone lead concentrations, but the computed parameters do not differ substantially from those derived by the more widely used method of IVW.

Combined micro-droplet and thin-film-assisted pre-concentration of lead traces for on-line monitoring using anodic stripping voltammetry.

PubMed

Belostotsky, Inessa; Gridin, Vladimir V; Schechter, Israel; Yarnitzky, Chaim N

2003-02-01

An improved analytical method for airborne lead traces is reported. It is based on using a Venturi scrubber sampling device for simultaneous thin-film stripping and droplet entrapment of aerosol influxes. At least threefold enhancement of the lead-trace pre-concentration is achieved. The sampled traces are analyzed by square-wave anodic stripping voltammetry. The method was tested by a series of pilot experiments. These were performed using contaminant-controlled air intakes. Reproducible calibration plots were obtained. The data were validated by traditional analysis using filter sampling. LODs are comparable with the conventional techniques. The method was successfully applied to on-line and in situ environmental monitoring of lead.

X-ray fluorescence determination of Sn, Sb, Pb in lead-based bearing alloys using a solution technique

NASA Astrophysics Data System (ADS)

Tian, Lunfu; Wang, Lili; Gao, Wei; Weng, Xiaodong; Liu, Jianhui; Zou, Deshuang; Dai, Yichun; Huang, Shuke

2018-03-01

For the quantitative analysis of the principal elements in lead-antimony-tin alloys, directly X-ray fluorescence (XRF) method using solid metal disks introduces considerable errors due to the microstructure inhomogeneity. To solve this problem, an aqueous solution XRF method is proposed for determining major amounts of Sb, Sn, Pb in lead-based bearing alloys. The alloy samples were dissolved by a mixture of nitric acid and tartaric acid to eliminated the effects of microstructure of these alloys on the XRF analysis. Rh Compton scattering was used as internal standard for Sb and Sn, and Bi was added as internal standard for Pb, to correct for matrix effects, instrumental and operational variations. High-purity lead, antimony and tin were used to prepare synthetic standards. Using these standards, calibration curves were constructed for the three elements after optimizing the spectrometer parameters. The method has been successfully applied to the analysis of lead-based bearing alloys and is more rapid than classical titration methods normally used. The determination results are consistent with certified values or those obtained by titrations.

Lead exposure in US worksites: A literature review and development of an occupational lead exposure database from the published literature

PubMed Central

Koh, Dong-Hee; Locke, Sarah J.; Chen, Yu-Cheng; Purdue, Mark P.; Friesen, Melissa C.

2016-01-01

Background Retrospective exposure assessment of occupational lead exposure in population-based studies requires historical exposure information from many occupations and industries. Methods We reviewed published US exposure monitoring studies to identify lead exposure measurement data. We developed an occupational lead exposure database from the 175 identified papers containing 1,111 sets of lead concentration summary statistics (21% area air, 47% personal air, 32% blood). We also extracted ancillary exposure-related information, including job, industry, task/location, year collected, sampling strategy, control measures in place, and sampling and analytical methods. Results Measurements were published between 1940 and 2010 and represented 27 2-digit standardized industry classification codes. The majority of the measurements were related to lead-based paint work, joining or cutting metal using heat, primary and secondary metal manufacturing, and lead acid battery manufacturing. Conclusions This database can be used in future statistical analyses to characterize differences in lead exposure across time, jobs, and industries. PMID:25968240

Approximation methods for control of structural acoustics models with piezoceramic actuators

NASA Astrophysics Data System (ADS)

Banks, H. T.; Fang, W.; Silcox, R. J.; Smith, R. C.

1993-01-01

The active control of acoustic pressure in a 2-D cavity with a flexible boundary (a beam) is considered. Specifically, this control is implemented via piezoceramic patches on the beam which produces pure bending moments. The incorporation of the feedback control in this manner leads to a system with an unbounded input term. Approximation methods in this manner leads to a system with an unbounded input term. Approximation methods in this manner leads to a system with an unbounded input team. Approximation methods in the context of linear quadratic regulator (LQR) state space control formulation are discussed and numerical results demonstrating the effectiveness of this approach in computing feedback controls for noise reduction are presented.

Evaluation of Vacuum Blasting and Heat Guns as Methods for Abating Lead- Based Paint on Buildings

DTIC Science & Technology

1993-09-01

INCOMPATIBILITY - Contact with powerful oxidizing agents such as FLUORINE, CHLORINE TRIFLUORIDE , MANGANESE TRIOXIDE, OXYGEN DIFLUORIDE, MANGANESE...investigating new technologies for lead-based paint abatement. This research evaluates the effectiveness , safety, LEC1L•.T• and cost of vacuum abrasive...paint abatement. This research evaluates the effectiveness , safety, and cost of vacuum abrasive units and heat guns as methods of removing lead-based

Subtraction method of computing QCD jet cross sections at NNLO accuracy

NASA Astrophysics Data System (ADS)

Trócsányi, Zoltán; Somogyi, Gábor

2008-10-01

We present a general subtraction method for computing radiative corrections to QCD jet cross sections at next-to-next-to-leading order accuracy. The steps needed to set up this subtraction scheme are the same as those used in next-to-leading order computations. However, all steps need non-trivial modifications, which we implement such that that those can be defined at any order in perturbation theory. We give a status report of the implementation of the method to computing jet cross sections in electron-positron annihilation at the next-to-next-to-leading order accuracy.

Sol-gel preparation of lead magnesium niobate (PMN) powders and thin films

DOEpatents

Boyle, T.J.

1999-01-12

A method of preparing a lead magnesium niobium oxide (PMN), Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}, precursor solution by a solvent method wherein a liquid solution of a lead-complex PMN precursor is combined with a liquid solution of a niobium-complex PMN precursor, the combined lead- and niobium-complex liquid solutions are reacted with a magnesium-alkyl solution, forming a PMN precursor solution and a lead-based precipitate, and the precipitate is separated from the reacted liquid PMN precursor solution to form a precipitate-free PMN precursor solution. This precursor solution can be processed to form both ferroelectric powders and thin films. 3 figs.

Sol-Gel Preparation Of Lead Magnesium Ni Obate (Pmn) Powdersand Thin Films

DOEpatents

Boyle, Timothy J.

1999-01-12

A method of preparing a lead magnesium niobium oxide (PMN), Pb(Mg.sub.1/3 Nb.sub.2/3)O.sub.3, precursor solution by a solvent method wherein a liquid solution of a lead-complex PMN precursor is combined with a liquid solution of a niobium-complex PMN precursor, the combined lead- and niobium-complex liquid solutions are reacted with a magnesium-alkyl solution, forming a PMN precursor solution and a lead-based precipitate, and the precipitate is separated from the reacted liquid PMN precursor solution to form a precipitate-free PMN precursor solution. This precursor solution can be processed to form both ferroelectric powders and thin films.

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2010 CFR

2010-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2014 CFR

2014-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2013 CFR

2013-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2012 CFR

2012-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

Code of Federal Regulations, 2011 CFR

2011-04-01

... POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and...

40 CFR 50.12 - National primary and secondary ambient air quality standards for lead.

Code of Federal Regulations, 2013 CFR

2013-07-01

... air quality standards for lead. 50.12 Section 50.12 Protection of Environment ENVIRONMENTAL PROTECTION... National primary and secondary ambient air quality standards for lead. (a) National primary and secondary ambient air quality standards for lead and its compounds, measured as elemental lead by a reference method...

40 CFR 50.12 - National primary and secondary ambient air quality standards for lead.

Code of Federal Regulations, 2012 CFR

2012-07-01

... air quality standards for lead. 50.12 Section 50.12 Protection of Environment ENVIRONMENTAL PROTECTION... National primary and secondary ambient air quality standards for lead. (a) National primary and secondary ambient air quality standards for lead and its compounds, measured as elemental lead by a reference method...

40 CFR 50.12 - National primary and secondary ambient air quality standards for lead.

Code of Federal Regulations, 2011 CFR

2011-07-01

... air quality standards for lead. 50.12 Section 50.12 Protection of Environment ENVIRONMENTAL PROTECTION... National primary and secondary ambient air quality standards for lead. (a) National primary and secondary ambient air quality standards for lead and its compounds, measured as elemental lead by a reference method...

Optical waveguides in fluoride lead silicate glasses fabricated by carbon ion implantation

NASA Astrophysics Data System (ADS)

Shen, Xiao-liang; Wang, Yue; Zhu, Qi-feng; Lü, Peng; Li, Wei-nan; Liu, Chun-xiao

2018-03-01

The carbon ion implantation with energy of 4.0 MeV and a dose of 4.0×1014 ions/cm2 is employed for fabricating the optical waveguide in fluoride lead silicate glasses. The optical modes as well as the effective refractive indices are measured by the prism coupling method. The refractive index distribution in the fluoride lead silicate glass waveguide is simulated by the reflectivity calculation method (RCM). The light intensity profile and the energy losses are calculated by the finite-difference beam propagation method (FD-BPM) and the program of stopping and range of ions in matter (SRIM), respectively. The propagation properties indicate that the C2+ ion-implanted fluoride lead silicate glass waveguide is a candidate for fabricating optical devices.

Method and apparatus for lead-unity-lag electric power generation system

NASA Technical Reports Server (NTRS)

Ganev, Evgeni (Inventor); Warr, William (Inventor); Salam, Mohamed (Arif) (Inventor)

2013-01-01

A method employing a lead-unity-lag adjustment on a power generation system is disclosed. The method may include calculating a unity power factor point and adjusting system parameters to shift a power factor angle to substantially match an operating power angle creating a new unity power factor point. The method may then define operation parameters for a high reactance permanent magnet machine based on the adjusted power level.

Method for measuring lead concentrations in blood

DOEpatents

Nogar, Nicholas S.

2001-01-01

Method for measuring lead concentrations in blood. The present invention includes the use of resonant laser ablation to analyze .ltoreq.1 .mu.L (or equivalent mass) samples of blood for lead content. A typical finger prick, for example, yields about 10 .mu.L. Solid samples may also readily be analyzed by resonant laser ablation. The sample is placed on a lead-free, electrically conducting substrate and irradiated with a single, focused laser beam which simultaneously vaporizes, atomizes, and resonantly ionizes an analyte of interest in a sample. The ions are then sorted, collected and detected using a mass spectrometer.

24 CFR 35.1340 - Clearance.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

24 CFR 35.1340 - Clearance.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

24 CFR 35.1345 - Occupant protection and worksite preparation.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1345 Occupant... occupants and the environment from contamination from lead-contaminated or lead-containing materials during...

24 CFR 35.1340 - Clearance.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

24 CFR 35.1345 - Occupant protection and worksite preparation.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1345 Occupant... occupants and the environment from contamination from lead-contaminated or lead-containing materials during...

24 CFR 35.1340 - Clearance.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

24 CFR 35.1345 - Occupant protection and worksite preparation.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1345 Occupant... occupants and the environment from contamination from lead-contaminated or lead-containing materials during...

24 CFR 35.1345 - Occupant protection and worksite preparation.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1345 Occupant... occupants and the environment from contamination from lead-contaminated or lead-containing materials during...

24 CFR 35.1345 - Occupant protection and worksite preparation.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1345 Occupant... occupants and the environment from contamination from lead-contaminated or lead-containing materials during...

24 CFR 35.1340 - Clearance.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint... abatement of lead-based paint or lead-based paint hazards shall be performed in accordance with 40 CFR 745...

40 CFR 60.374 - Test methods and procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... = concentration of lead emissions for the entire facility, mg/dscm (gr/dscf). Ca = concentration of lead emissions from facility “a”, mg/dscm (gr/dscf). Qsda = volumetric flow rate of effluent gas from facility “a...=emission rate of lead, mg/kg (lb/ton) of lead charged. CPbi = concentration of lead from emission point “i...

User's manual for interfacing a leading edge, vortex rollup program with two linear panel methods

NASA Technical Reports Server (NTRS)

Desilva, B. M. E.; Medan, R. T.

1979-01-01

Sufficient instructions are provided for interfacing the Mangler-Smith, leading edge vortex rollup program with a vortex lattice (POTFAN) method and an advanced higher order, singularity linear analysis for computing the vortex effects for simple canard wing combinations.

Comparison of Hydrogen Sulfide Analysis Techniques

ERIC Educational Resources Information Center

Bethea, Robert M.

1973-01-01

A summary and critique of common methods of hydrogen sulfide analysis is presented. Procedures described are: reflectance from silver plates and lead acetate-coated tiles, lead acetate and mercuric chloride paper tapes, sodium nitroprusside and methylene blue wet chemical methods, infrared spectrophotometry, and gas chromatography. (BL)

A theoretical investigation of the aerodynamics of low-aspect-ratio wings with partial leading-edge separation

NASA Technical Reports Server (NTRS)

Mehrotra, S. C.; Lan, C. E.

1978-01-01

A numerical method is developed to predict distributed and total aerodynamic characteristics for low aspect-ratio wings with partial leading-edge separation. The flow is assumed to be steady and inviscid. The wing boundary condition is formulated by the quasi-vortex-lattice method. The leading-edge separated vortices are represented by discrete free vortex elements which are aligned with the local velocity vector at mid-points to satisfy the force free condition. The wake behind the trailing-edge is also force free. The flow tangency boundary condition is satisfied on the wing, including the leading- and trailing-edges. Comparison of the predicted results with complete leading-edge separation has shown reasonably good agreement. For cases with partial leading-edge separation, the lift is found to be highly nonlinear with angle of attack.

Recycling of Exhaust Batteries in Lead-Foam Electrodes

NASA Astrophysics Data System (ADS)

Costanza, Girolamo; Tata, Maria Elisa

Lead and lead-alloy foams have been investigated in this research. In particular low-cost techniques for the direct production of lead-based electrodes have been analyzed and discussed in this work. The relevance of the main process parameters (powder compacting pressure, granulometry, base metal composition, sintering temperature and time) have been focused and the effect on foam morphology has been discussed too. In particular "Sintering and Dissolution Process" (SDP) and "Replication Process" (RP) have been employed and suitable modified. Both spherical urea and NaCl have been adopted in the SDP method. In the replication process it has been evidenced that the viscosity of the melt is fundamental. Furthermore the research examines lead recovery and recycling of exhaust batteries into foam-based electrodes. A novel method for the direct conversion of Pb scrap into lead foam is discussed too.

Lead and cadmium in human placentas and maternal and neonatal blood (in a heavily polluted area) measured by graphite furnace atomic absorption spectrometry.

PubMed Central

Baranowska, I

1995-01-01

OBJECTIVE--To measure the concentrations of the trace elements lead and cadmium in human placenta and in maternal and neonatal (cord) blood. To assess the influence of the strongly polluted environment on the content of metals in tissues and on the permeability of placenta to cadmium and lead. Various methods of mineralisation were tested before analysis. METHODS--Graphite furnace atomic absorption spectrometry was used for the determination of lead and cadmium. The samples for analysis were prepared by mineralisation under pressure in a Teflon bomb (HNO3, 110 degrees C), by wet ashing under normal pressure (HNO3 + H2O2 for 12 hours), and by microwave digestion in concentrated nitric acid. RESULTS--In analysed samples the following mean concentrations of cadmium and lead were found: in venous blood Pb = 72.50 ng/ml, Cd = 4.90 ng/ml; in placenta Pb = 0.50 microgram/g, Cd = 0.11 microgram/g; in cord blood Pb = 38.31 ng/ml, Cd = 1.13 ng/ml. CONCLUSION--High concentrations of lead and cadmium were found in placentas and in maternal blood whereas in neonatal blood there was an increased concentration of lead and only traces of cadmium. It is concluded that the placenta is a better barrier for cadmium than for lead. Among the examined methods of mineralisation, microwave digestion was the best. PMID:7795737

First detection of lead in black paper from intraoral film: an environmental concern.

PubMed

Guedes, Débora F C; Silva, Reginaldo S; da Veiga, Márcia A M S; Pecora, Jesus D

2009-10-30

Lead (Pb) contamination in the black paper that recovers intraoral films (BKP) has been investigated. BKP samples were collected from the Radiology Clinics of the Dental School of Ribeirão Preto, University of São Paulo, Brazil. For sake of comparison, four different methods were used. The results revealed the presence of high lead levels, well above the maximum limit allowed by the legislation. Pb contamination levels achieved after the following treatments: paper digestion in nitric acid, microwave treatment, DIN38414-54 method and TCLP method were 997 microg g(-1), 189 microg g(-1), 20.8 microg g(-1), and 54.0 microg g(-1), respectively. Flame atomic absorption spectrometry (FAAS) and inductively coupled plasma mass spectrometry (ICP-MS) were employed for lead determination according to the protocols of the applied methods. Lead contamination in used BKP was confirmed by scanning electron microscopy coupled with energy dispersive X-ray microanalysis (SEM-EDS). All the SEM imaging was carried out in the secondary electron mode (SE) and backscattered-electron mode (QBSD) following punctual X-ray fluorescence spectra. Soil contamination derived from this product revealed the urgent need of addressing this problem. These elevated Pb levels, show that a preliminary treatment of BKP is mandatory before it is disposed into the common trash. The high lead content of this material makes its direct dumping into the environment unwise.

A fast method for the determination of lead in honey samples using stabilizer-free silver nanoparticles

NASA Astrophysics Data System (ADS)

Bittar, Dayana Borges; Catelani, Tiago Augusto; Pezza, Leonardo; Pezza, Helena Redigolo

2018-01-01

A sensitive, rapid and robust method based on the use of stabilizer-free silver nanoparticles was developed for lead detection in honey. Silver nanoparticles were synthesized without the presence of any stabilizers using silver nitrate and sodium borohydride as precursors where the latter was applied as reducing agent. The optimization of the experimental variables (AgNO3 and NaBH4) for the formation of the nanoparticles was carried out using varying volumes of these solutions. Spectrophotometric measurements at 393 nm showed a linear working range between 0.0500 and 0.167 mg L- 1 lead (R = 0.994), with limits of detection (LOD) and quantification (LOQ) of 0.0135 and 0.0451 mg L- 1, respectively. The proposed method proved to be a significantly sensitive mechanism for lead detection in honey samples.

A Role for Fragment-Based Drug Design in Developing Novel Lead Compounds for Central Nervous System Targets.

PubMed

Wasko, Michael J; Pellegrene, Kendy A; Madura, Jeffry D; Surratt, Christopher K

2015-01-01

Hundreds of millions of U.S. dollars are invested in the research and development of a single drug. Lead compound development is an area ripe for new design strategies. Therapeutic lead candidates have been traditionally found using high-throughput in vitro pharmacological screening, a costly method for assaying thousands of compounds. This approach has recently been augmented by virtual screening (VS), which employs computer models of the target protein to narrow the search for possible leads. A variant of VS is fragment-based drug design (FBDD), an emerging in silico lead discovery method that introduces low-molecular weight fragments, rather than intact compounds, into the binding pocket of the receptor model. These fragments serve as starting points for "growing" the lead candidate. Current efforts in virtual FBDD within central nervous system (CNS) targets are reviewed, as is a recent rule-based optimization strategy in which new molecules are generated within a 3D receptor-binding pocket using the fragment as a scaffold. This process not only places special emphasis on creating synthesizable molecules but also exposes computational questions worth addressing. Fragment-based methods provide a viable, relatively low-cost alternative for therapeutic lead discovery and optimization that can be applied to CNS targets to augment current design strategies.

A Role for Fragment-Based Drug Design in Developing Novel Lead Compounds for Central Nervous System Targets

PubMed Central

Wasko, Michael J.; Pellegrene, Kendy A.; Madura, Jeffry D.; Surratt, Christopher K.

2015-01-01

Hundreds of millions of U.S. dollars are invested in the research and development of a single drug. Lead compound development is an area ripe for new design strategies. Therapeutic lead candidates have been traditionally found using high-throughput in vitro pharmacological screening, a costly method for assaying thousands of compounds. This approach has recently been augmented by virtual screening (VS), which employs computer models of the target protein to narrow the search for possible leads. A variant of VS is fragment-based drug design (FBDD), an emerging in silico lead discovery method that introduces low-molecular weight fragments, rather than intact compounds, into the binding pocket of the receptor model. These fragments serve as starting points for “growing” the lead candidate. Current efforts in virtual FBDD within central nervous system (CNS) targets are reviewed, as is a recent rule-based optimization strategy in which new molecules are generated within a 3D receptor-binding pocket using the fragment as a scaffold. This process not only places special emphasis on creating synthesizable molecules but also exposes computational questions worth addressing. Fragment-based methods provide a viable, relatively low-cost alternative for therapeutic lead discovery and optimization that can be applied to CNS targets to augment current design strategies. PMID:26441817

Lead isotope ratios for bullets, a descriptive approach for investigative purposes and a new method for sampling of bullet lead.

PubMed

Sjåstad, Knut-Endre; Simonsen, Siri Lene; Andersen, Tom H

2014-11-01

To establish a link between a bullet fired from a suspected firearm, investigation of striation marks are one of the corner stones in the forensic laboratory. Nevertheless, on some occasions, the bullet may be deformed to such extent that traditional investigation of striation marks will be impossible. Fragments of lead can be investigated by lead isotope ratio determination in order to distinguish between bullets with different origin. This approach initially seems reasonable, since the abundance of lead isotopes varies significantly in nature. To make a method valid for forensic purposes, it is important to have a fundamental understanding of the variation within a box of lead bullets and the expected variation between boxes. Studies of variability within and between boxes of ammunition are imperative to perform any type of forensic interpretation, both in an investigative and evaluative context. This work presents an extensive study of variability within and between boxes of ammunition by use of multicollector inductive coupled mass spectrometry. As a first approximation to classify bullets to any given source, a simple and robust graphical method is presented. In addition, an easy-to-use sampling procedure of lead is presented. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Lead: Aspects of its ecology and environmental toxicity. [physiological effects of lead compound contamination of environment

NASA Technical Reports Server (NTRS)

Siegel, S. M.

1973-01-01

An analysis of lead toxicity in the Hawaiian environment was conducted. It was determined that lead enters the environment as an industrial contaminant resulting from the combustion of leaded gasoline. The amount of lead absorbed by the plants in various parts of the Hawaiian Islands is reported. The disposition of lead in the sediments of canals and yacht basins was investigated. The methods for conducting the surveys of lead content are described. Possible consequences of continued environmental pollution by burning leaded gasoline are discussed.

Efficacy of a lead based paint XRF analyzer and a commercially available colorimetric lead test kit as qualitative field tools for determining presence of lead in religious powders.

PubMed

Shah, Manthan P; Shendell, Derek G; Meng, Qingyu; Ohman-Strickland, Pamela; Halperin, William

2018-04-23

The performances of a portable X-Ray Fluorescence (XRF) lead paint analyzer (RMD LPA-1, Protec Instrument Corp., Waltham, MA) and a commercially available colorimetric lead test kit (First Alert Lead Test Kit, eAccess Solutions, Inc., Palatine, IL) were evaluated for use by local or state health departments as potential cost-effective rapid analysis or "spot test" field techniques for tentative identification of lead content in sindoor powders. For both field-sampling methods, sensitivity, specificity and predictive values varied widely for samples containing <300,000 μg/g lead. For samples containing ≥300,000 μg/g lead, the aforementioned metrics were 100% (however, the CIs had a wide range). In addition, both field sampling methods showed clear, consistent positive readings only for samples containing ≥300,000 μg/g lead. Even samples with lead content as high as 5,110 μg/g were not positively identified by either field analysis technique. The results of this study suggest the XRF analyzer and colorimetric lead test kit cannot be used as a rapid field test for sindoor by health department inspectors.

An analysis of occupational blood lead trends in Manitoba, 1979 through 1987

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yassi, A.; Cheang, M.; Tenenbein, M.

1991-06-01

While regulations for workplace lead exposure become more strict, their effectiveness in decreasing blood lead concentrations and the method by which this is attained have not been evaluated. METHODS: An analysis was conducted of 10,190 blood lead samples from employees of 10 high-risk workplaces collected in Manitoba, 1979-87, as part of regulated occupational surveillance. A significant decrease in blood lead concentrations was observed overall as well as for each individual company. A 1979 government regulation to reduce blood lead to below 3.38 mumol/L (70 micrograms/dl) was followed by a drop in blood lead concentrations; a 1983 order to reduce bloodmore » leads to below 2.90 mumol/L (60 micrograms/dl) was not followed by such a drop. Longitudinal analysis by individual workers suggested that companies were complying by use of administrative control, i.e., removing workers to lower lead areas until blood lead levels had fallen, then returning them to high lead areas. Focusing upon blood lead as the sole criterion for compliance is not effective; regulations must specifically require environmental monitoring and controls. Biological surveillance serves as 'back-up' to environmental surveillance and this database illustrates the usefulness of a comprehensive centralized surveillance system.« less

Comparison of Digital 12-Lead ECG and Digital 12-Lead Holter ECG Recordings in Healthy Male Subjects: Results from a Randomized, Double-Blinded, Placebo-Controlled Clinical Trial.

PubMed

Wang, Duolao; Bakhai, Ameet; Arezina, Radivoj; Täubel, Jörg

2016-11-01

Electrocardiogram (ECG) variability is greatly affected by the ECG recording method. This study aims to compare Holter and standard ECG recording methods in terms of central locations and variations of ECG data. We used the ECG data from a double-blinded, placebo-controlled, randomized clinical trial and used a mixed model approach to assess the agreement between two methods in central locations and variations of eight ECG parameters (Heart Rate, PR, QRS, QT, RR, QTcB, QTcF, and QTcI intervals). A total of 34 heathy male subjects with mean age of 25.7 ± 4.78 years were randomized to receive either active drug or placebo. Digital 12-lead ECG and digital 12-lead Holter ECG recordings were performed to assess ECG variability. There are no significant differences in least square mean between the Holter and the standard method for all ECG parameters. The total variance is consistently higher for the Holter method than the standard method for all ECG parameters except for QRS. The intraclass correlation coefficient (ICC) values for the Holter method are consistently lower than those for the standard method for all ECG parameters except for QRS, in particular, the ICC for QTcF is reduced from 0.86 for the standard method to 0.67 for the Holter method. This study suggests that Holter ECGs recorded in a controlled environment are not significantly different but more variable than those from the standard method. © 2016 Wiley Periodicals, Inc.

24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2012-04-01 2012-04-01 false Ongoing lead-based paint...

24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2013-04-01 2013-04-01 false Ongoing lead-based paint...

24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2011-04-01 2011-04-01 false Ongoing lead-based paint...

24 CFR 35.1355 - Ongoing lead-based paint maintenance and reevaluation activities.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities... 24 Housing and Urban Development 1 2014-04-01 2014-04-01 false Ongoing lead-based paint...

Lead line in rodents: an old sign of lead intoxication turned into a new method for environmental surveillance.

PubMed

de Figueiredo, Fellipe Augusto Tocchini; Ramos, Junia; Kawakita, Erika R Hashimoto; Bilal, Alina S; de Sousa, Frederico B; Swaim, William D; Issa, Joao P Mardegan; Gerlach, Raquel F

2016-11-01

The "lead line" was described by Henry Burton in 1840. Rodents are used as sentinels to monitor environmental pollution, but their teeth have not been used to determine lead. To determine whether lead deposits can be observed in the teeth of lead-exposed animals, since the gingival deposits known as "lead line" would likely have a correlate in the calcified tissue to which the gums are opposed during life. Male Wistar rats were exposed to lead in the drinking water (30 mg/L) since birth until 60 days-old. Molars and the incisors of each hemimandible were analyzed by scanning electron microscopy (SEM) on regular and backscattered electrons (BSE) mode. Elements were determined using electron dispersive spectroscopy (EDS). Clean cervical margins were observed on control teeth, as opposed to the findings of extensive deposits on lead-exposed animals, even in hemimandibles that had been exhumed after being buried for 90 days. BSE/EDS indicated that those deposits were an exogenous material compatible with lead sulfite. Presence of calcium, phosphorus, magnesium, carbon, lead, and oxygen is presented. Lead-exposed animals presented marked root resorption. The lead deposits characterized here for the first time show that the "lead line" seen in gums has a calcified tissue counterpart, that is detectable post-mortem even in animals exposed to a low dose of lead. This is likely a good method to detect undue lead exposure and will likely have wide application for pollution surveillance using sentinels.

Poisoning of wild birds from exposure to anticholinesterase compounds and lead: diagnostic methods and selected cases

USGS Publications Warehouse

Franson, J. Christian; Smith, Milton R.

1999-01-01

Organophosphorus and carbamate compounds have largely replaced chlorinated hydrocarbons for pesticidal use in the United States, and many cases of poisoning resulting from exposure to these anticholinesterase agents have occurred in free-living birds. Although lead shot has been prohibited for waterfowl hunting throughout the United States since 1991, lead poisoning from the ingestion of spent lead shot is still occasionally seen in wild birds, and lead poisoning from the ingestion of fishing sinkers is an emerging issue of concern. A thorough history, a complete necropsy evaluation, and appropriate laboratory analysis of tissues are required to diagnose toxicoses in wild birds, including those caused by anticholinesterase compounds and lead. The interpretation of brain cholinesterase (ChE) activity results depends on the methods of analysis and comparison with expected normal enzyme activities in brain tissue from the same species. Although lead residues in tissues vary among species, many lead poisoned birds have tissue residues that are much higher than the lower threshold commonly accepted for a diagnosis of lead poisoning. We review histories, necropsy findings, and analytical methodologies and results for selected anticholinesterase and lead poisoning cases diagnosed in wild raptors, waterfowl, and loons.

Adaptive allocation for binary outcomes using decreasingly informative priors.

PubMed

Sabo, Roy T

2014-01-01

A method of outcome-adaptive allocation is presented using Bayes methods, where a natural lead-in is incorporated through the use of informative yet skeptical prior distributions for each treatment group. These prior distributions are modeled on unobserved data in such a way that their influence on the allocation scheme decreases as the trial progresses. Simulation studies show this method to behave comparably to the Bayesian adaptive allocation method described by Thall and Wathen (2007), who incorporate a natural lead-in through sample-size-based exponents.

Improvement of calculation method for electrical parameters of short network of ore-thermal furnaces

NASA Astrophysics Data System (ADS)

Aliferov, A. I.; Bikeev, R. A.; Goreva, L. P.

2017-10-01

The paper describes a new calculation method for active and inductive resistance of split interleaved current leads packages in ore-thermal electric furnaces. The method is developed on basis of regression analysis of dependencies of active and inductive resistances of the packages on their geometrical parameters, mutual disposition and interleaving pattern. These multi-parametric calculations have been performed with ANSYS software. The proposed method allows solving split current lead electrical parameters minimization and balancing problems for ore-thermal furnaces.

Virtual screening methods as tools for drug lead discovery from large chemical libraries.

PubMed

Ma, X H; Zhu, F; Liu, X; Shi, Z; Zhang, J X; Yang, S Y; Wei, Y Q; Chen, Y Z

2012-01-01

Virtual screening methods have been developed and explored as useful tools for searching drug lead compounds from chemical libraries, including large libraries that have become publically available. In this review, we discussed the new developments in exploring virtual screening methods for enhanced performance in searching large chemical libraries, their applications in screening libraries of ~ 1 million or more compounds in the last five years, the difficulties in their applications, and the strategies for further improving these methods.

Strand-Specific Analysis of DNA Synthesis and Proteins Association with DNA Replication Forks in Budding Yeast.

PubMed

Yu, Chuanhe; Gan, Haiyun; Zhang, Zhiguo

2018-01-01

DNA replication initiates at DNA replication origins after unwinding of double-strand DNA(dsDNA) by replicative helicase to generate single-stranded DNA (ssDNA) templates for the continuous synthesis of leading-strand and the discontinuous synthesis of lagging-strand. Therefore, methods capable of detecting strand-specific information will likely yield insight into the association of proteins at leading and lagging strand of DNA replication forks and the regulation of leading and lagging strand synthesis during DNA replication. The enrichment and Sequencing of Protein-Associated Nascent DNA (eSPAN), which measure the relative amounts of proteins at nascent leading and lagging strands of DNA replication forks, is a step-wise procedure involving the chromatin immunoprecipitation (ChIP) of a protein of interest followed by the enrichment of protein-associated nascent DNA through BrdU immunoprecipitation. The isolated ssDNA is then subjected to strand-specific sequencing. This method can detect whether a protein is enriched at leading or lagging strand of DNA replication forks. In addition to eSPAN, two other strand-specific methods, (ChIP-ssSeq), which detects potential protein-ssDNA binding and BrdU-IP-ssSeq, which can measure synthesis of both leading and lagging strand, were developed along the way. These methods can provide strand-specific and complementary information about the association of the target protein with DNA replication forks as well as synthesis of leading and lagging strands genome wide. Below, we describe the detailed eSPAN, ChIP-ssSeq, and BrdU-IP-ssSeq protocols.

Determination of lead and cadmium in soils, sludges, and fertilizers by an ion-exchange/spectrophotometric method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heinzig, M.; DeYong, G.D.; Anglin, R.J.

1993-12-01

The MetalTrace method, which consists of an anion-exchange separation coupled with a spectrophotometric quantification, was used to determine lead and cadmium in sulfuric acid-hydrogen peroxide digests of soils and sludges and hydrobromic acid extracts of soils. Cadmium only was determined in sulfuric acid-hydrogen peroxide digests of fertilizers because no standards were available with certified lead contents. The selectivity provided by the anion-exchange separation allowed the use of a spectrophotometric indicator with an extremely high extinction coefficient so that detection limits in the low parts per million range could be attained. The results obtained using this method compared favorably with thosemore » obtained using much more expensive methods requiring more specialized training and equipment.« less

[Simultaneous determination of trace amounts of zinc, cadmium, lead and copper by the method of anodic voltammetry using factor experimental design].

PubMed

Koen, E

1975-01-01

Using the method of factor planning of the experiment, the author studies and demonstrates the influence exerted by the potential and time of electrolysis, and by the concentration of the background and elements on the heights of anodal peaks upon simultaneous determination of zinc, cadmium, lead and copper microconcentrations. On the ground of statistical elaboration of the results, the optimal condition for polarographic determination through anodal voltamperometry are outlined. According to the cyclic voltametry method, the electrod processes reversibility for zinc, cadmium and lead, as well as the incomplete reversibility for copper are established; the number of electrons participating in the electrochemical reaction are found using the method of gas coulometry. The possibility of simultaneous determination of the four elements' ultramicroconcentrations after the method of voltamperometry with enrichment is proved. The standard deviation is in the range 3.02 to 4.9.

Evaluation of Methods for Analysis of Lead in Air Particulates: An Intra-Laboratory and Inter-Laboratory Comparison

EPA Science Inventory

In 2008, the United States Environmental Protection Agency (USEPA) set a new National Ambient Air Quality Standard (NAAQS) for lead (Pb) in total suspended particulate matter (Pb-TSP) which called for significant decreases in the allowable limits. The Federal Reference Method (FR...

Method and apparatus for connecting high voltage leads to a high temperature super-conducting transformer

DOEpatents

Golner, Thomas M.; Mehta, Shirish P.

2005-07-26

A method and apparatus for connecting high voltage leads to a super-conducting transformer is provided that includes a first super-conducting coil set, a second super-conducting coil set, and a third super-conducting coil set. The first, second and third super-conducting coil sets are connected via an insulated interconnect system that includes insulated conductors and insulated connectors that are utilized to connect the first, second, and third super-conducting coil sets to the high voltage leads.

Childhood lead poisoning investigations: evaluating a portable instrument for testing soil lead.

PubMed

Reames, Ginger; Lance, Larrie L

2002-04-01

The Childhood Lead Poisoning Prevention Branch of the California Department of Health Services evaluated a portable X-ray fluorescence (XRF) instrument for use as a soil lead-testing tool during environmental investigations of lead-poisoned children's homes. A Niton XRF was used to test soil at 119 sampling locations in the yards of 11 San Francisco Bay Area houses. Niton XRF readings were highly correlated with laboratory results and met the study criteria for an acceptable screening method. The data suggest that the most health-protective and time-efficient approach to testing for soil lead above regulatory levels is to take either surface readings or readings of a test cup of soil prepared by grinding with a mortar and pestle. The advantage of the test cup method is that the test cup with soil may be submitted to a laboratory for confirmatory analysis.

Survey of Manual Methods of Measurements of Asbestos, Beryllium, Lead, Cadmium, Selenium, and Mercury in Stationary Source Emissions. Environmental Monitoring Series.

ERIC Educational Resources Information Center

Coulson, Dale M.; And Others

The purpose of this study is to evaluate existing manual methods for analyzing asbestos, beryllium, lead, cadmium, selenium, and mercury, and from this evaluation to provide the best and most practical set of analytical methods for measuring emissions of these elements from stationary sources. The work in this study was divided into two phases.…

Costs of IQ Loss from Leaded Aviation Gasoline Emissions

PubMed Central

Wolfe, Philip J.; Giang, Amanda; Ashok, Akshay; Selin, Noelle E.; Barrett, Steven R. H.

2017-01-01

In the United States, general aviation piston-driven aircraft are now the largest source of lead emitted to the atmosphere. Elevated lead concentrations impair children’s IQ and can lead to lower earnings potentials. This study is the first assessment of the nationwide annual costs of IQ losses from aircraft lead emissions. We develop a general aviation emissions inventory for the continental United States and model its impact on atmospheric concentrations using the Community Multi-Scale Air Quality Model (CMAQ). We use these concentrations to quantify the impacts of annual aviation lead emissions on the U.S. population using two methods: through static estimates of cohort-wide IQ deficits and through dynamic economy-wide effects using a computational general equilibrium model. We also examine the sensitivity of these damage estimates to different background lead concentrations, showing the impact of lead controls and regulations on marginal costs. We find that aircraft-attributable lead contributes to $1.06 billion 2006 USD ($0.01 – $11.6) in annual damages from lifetime earnings reductions, and that dynamic economy-wide methods result in damage estimates that are 54% larger. Because the marginal costs of lead are dependent on background concentration, the costs of piston-driven aircraft lead emissions are expected to increase over time as regulations on other emissions sources are tightened. PMID:27494542

Costs of IQ Loss from Leaded Aviation Gasoline Emissions.

PubMed

Wolfe, Philip J; Giang, Amanda; Ashok, Akshay; Selin, Noelle E; Barrett, Steven R H

2016-09-06

In the United States, general aviation piston-driven aircraft are now the largest source of lead emitted to the atmosphere. Elevated lead concentrations impair children's IQ and can lead to lower earnings potentials. This study is the first assessment of the nationwide annual costs of IQ losses from aircraft lead emissions. We develop a general aviation emissions inventory for the continental United States and model its impact on atmospheric concentrations using the community multi-scale air quality model (CMAQ). We use these concentrations to quantify the impacts of annual aviation lead emissions on the U.S. population using two methods: through static estimates of cohort-wide IQ deficits and through dynamic economy-wide effects using a computational general equilibrium model. We also examine the sensitivity of these damage estimates to different background lead concentrations, showing the impact of lead controls and regulations on marginal costs. We find that aircraft-attributable lead contributes to $1.06 billion 2006 USD ($0.01-$11.6) in annual damages from lifetime earnings reductions, and that dynamic economy-wide methods result in damage estimates that are 54% larger. Because the marginal costs of lead are dependent on background concentration, the costs of piston-driven aircraft lead emissions are expected to increase over time as regulations on other emissions sources are tightened.

Periodical capacity setting methods for make-to-order multi-machine production systems

PubMed Central

Altendorfer, Klaus; Hübl, Alexander; Jodlbauer, Herbert

2014-01-01

The paper presents different periodical capacity setting methods for make-to-order, multi-machine production systems with stochastic customer required lead times and stochastic processing times to improve service level and tardiness. These methods are developed as decision support when capacity flexibility exists, such as, a certain range of possible working hours a week for example. The methods differ in the amount of information used whereby all are based on the cumulated capacity demand at each machine. In a simulation study the methods’ impact on service level and tardiness is compared to a constant provided capacity for a single and a multi-machine setting. It is shown that the tested capacity setting methods can lead to an increase in service level and a decrease in average tardiness in comparison to a constant provided capacity. The methods using information on processing time and customer required lead time distribution perform best. The results found in this paper can help practitioners to make efficient use of their flexible capacity. PMID:27226649

Applicability of linearized-theory attached-flow methods to design and analysis of flap systems at low speeds for thin swept wings with sharp leading edges

NASA Technical Reports Server (NTRS)

Carlson, Harry W.; Darden, Christine M.

1987-01-01

Low-speed experimental force and data on a series of thin swept wings with sharp leading edges and leading and trailing-edge flaps are compared with predictions made using a linearized-theory method which includes estimates of vortex forces. These comparisons were made to assess the effectiveness of linearized-theory methods for use in the design and analysis of flap systems in subsonic flow. Results demonstrate that linearized-theory, attached-flow methods (with approximate representation of vortex forces) can form the basis of a rational system for flap design and analysis. Even attached-flow methods that do not take vortex forces into account can be used for the selection of optimized flap-system geometry, but design-point performance levels tend to be underestimated unless vortex forces are included. Illustrative examples of the use of these methods in the design of efficient low-speed flap systems are included.

Method of fabricating a PbS-PbSe IR detector array

NASA Technical Reports Server (NTRS)

Barrett, John R. (Inventor)

1987-01-01

A silicon wafer is provided which does not employ individually bonded leads between the IR sensitive elements and the input stages of multiplexers. The wafer is first coated with lead selenide in a first detector array area and is thereafter coated with lead sulfide within a second detector array area. The described steps result in the direct chemical deposition of lead selenide and lead sulfide upon the silicon wafer to eliminate individual wire bonding, bumping, flip chiping, planar interconnecting methods of connecting detector array elements to silicon chip circuitry, e.g., multiplexers, to enable easy fabrication of very long arrays. The electrode structure employed, produces an increase in the electrical field gradient between the electrodes for a given volume of detector material, relative to conventional electrode configurations.

Characterizing artifacts in RR stress test time series.

PubMed

Astudillo-Salinas, Fabian; Palacio-Baus, Kenneth; Solano-Quinde, Lizandro; Medina, Ruben; Wong, Sara

2016-08-01

Electrocardiographic stress test records have a lot of artifacts. In this paper we explore a simple method to characterize the amount of artifacts present in unprocessed RR stress test time series. Four time series classes were defined: Very good lead, Good lead, Low quality lead and Useless lead. 65 ECG, 8 lead, records of stress test series were analyzed. Firstly, RR-time series were annotated by two experts. The automatic methodology is based on dividing the RR-time series in non-overlapping windows. Each window is marked as noisy whenever it exceeds an established standard deviation threshold (SDT). Series are classified according to the percentage of windows that exceeds a given value, based upon the first manual annotation. Different SDT were explored. Results show that SDT close to 20% (as a percentage of the mean) provides the best results. The coincidence between annotators classification is 70.77% whereas, the coincidence between the second annotator and the automatic method providing the best matches is larger than 63%. Leads classified as Very good leads and Good leads could be combined to improve automatic heartbeat labeling.

BLOOD LEAD CONCENTRATION AND DELAYED PUBERTY IN GIRLS

EPA Science Inventory

Background
Environmental lead exposure has been linked to alterations in growth and endocrine function. It is not known whether such exposure affects pubertal development.

Methods
We analyzed the relations between blood lead concentration and pubertal...

Chicago Lead in Drinking Water Study

EPA Pesticide Factsheets

EPA Region 5 and the Chicago Department of Water Management conducted a study on field sampling protocols for lead in drinking water. The purpose of the study was to evaluate the method used by public water systems to monitor lead levels.

Calculation of vortex lift effect for cambered wings by the suction analogy

NASA Technical Reports Server (NTRS)

Lan, C. E.; Chang, J. F.

1981-01-01

An improved version of Woodward's chord plane aerodynamic panel method for subsonic and supersonic flow is developed for cambered wings exhibiting edge separated vortex flow, including those with leading edge vortex flaps. The exact relation between leading edge thrust and suction force in potential flow is derived. Instead of assuming the rotated suction force to be normal to wing surface at the leading edge, new orientation for the rotated suction force is determined through consideration of the momentum principle. The supersonic suction analogy method is improved by using an effective angle of attack defined through a semi-empirical method. Comparisons of predicted results with available data in subsonic and supersonic flow are presented.

Epsilon Waves Detected by Various Electrocardiographic Recording Methods in Patients with Arrhythmogenic Right Ventricular Cardiomyopathy

PubMed Central

Wang, Jing; Yang, Bing; Chen, Hongwu; Ju, Weizhu; Chen, Kai; Zhang, Fengxiang; Cao, Kejiang; Chen, Minglong

2010-01-01

We analyzed the shape and distribution of epsilon waves by 3 various methods of electrocardiographic recording in patients with arrhythmogenic right ventricular cardiomyopathy. Thirty-two patients who met recognized diagnostic criteria for arrhythmogenic right ventricular cardiomyopathy were included in this study (24 men and 8 women; mean age, 42.3 ± 12.9 yr). Epsilon waves were detected by standard 12-lead electrocardiography (S-ECG), right-sided precordial lead electrocardiography (R-ECG), and Fontaine bipolar precordial lead electrocardiography (F-ECG). We found 3 types of epsilon waves: wiggle waves, small spike waves, and smooth potential waves that formed an atypical prolonged R' wave. The most common configuration was small spiked waves. In some circumstances, epsilon waves were evident in some leads (especially in leads V1 through V3), but notches were recorded in the other leads during the corresponding phase. These waves could be detected only by S-ECG in 1 patient, R-ECG in 3 patients, and F-ECG in 5 patients; the rates of epsilon-wave detection by these 3 methods were 38% (12/32), 38% (12/32), and 50% (16/32), respectively. However, the detection rate using combined methods was significantly higher than that by S-ECG alone (SF-ECG 56% vs S-ECG 38%, P = 0.0312; and SRF-ECG 66% vs S-ECG 38%, P = 0.0039). In addition, the rate of widespread T-wave inversion (exceeding V3) was significantly higher in patients with epsilon waves than in those without (48% vs 9%, P = 0.029), as was ventricular tachycardia (95% vs 64%, P = 0.019). These 3 electrocardiographic recording methods should be used in combination to improve the detection rate of epsilon waves. PMID:20844612

Liquid electrode plasma-optical emission spectrometry combined with solid-phase preconcentration for on-site analysis of lead.

PubMed

Barua, Suman; Rahman, Ismail M M; Alam, Iftakharul; Miyaguchi, Maho; Sawai, Hikaru; Maki, Teruya; Hasegawa, Hiroshi

2017-08-15

A relatively rapid and precise method is presented for the determination of lead in aqueous matrix. The method consists of analyte quantitation using the liquid electrode plasma-optical emission spectrometry (LEP-OES) coupled with selective separation/preconcentration by solid-phase extraction (SPE). The impact of operating variables on the retention of lead in SPEs such as pH, flow rate of the sample solution; type, volume, flow rate of the eluent; and matrix effects were investigated. Selective SPE-separation/preconcentration minimized the interfering effect due to manganese in solution and limitations in lead-detection in low-concentration samples by LEP-OES. The LEP-OES operating parameters such as the electrical conductivity of sample solution; applied voltage; on-time, off-time, pulse count for applied voltage; number of measurements; and matrix effects have also been optimized to obtain a distinct peak for the lead at λ max =405.8nm. The limit of detection (3σ) and the limit of quantification (10σ) for lead determination using the technique were found as 1.9 and 6.5ng mL -1 , respectively. The precision, as relative standard deviation, was lower than 5% at 0.1μg mL -1 Pb, and the preconcentration factor was found to be 187. The proposed method was applied to the analysis of lead contents in the natural aqueous matrix (recovery rate:>95%). The method accuracy was verified using certified reference material of wastewaters: SPS-WW1 and ERM-CA713. The results from LEP-OES were in good agreement with inductively coupled plasma optical emission spectrometry measurements of the same samples. The application of the method is rapid (≤5min, without preconcentration) with a reliable detection limit at trace levels. Copyright © 2017 Elsevier B.V. All rights reserved.

Evaluation of a Low-Cost Commercially Available Extraction Device for Assessing Lead Bioaccessibility in Contaminated Soils

EPA Science Inventory

The U.S. EPA’s in vitro bioaccessibility (IVBA) method 9200.1-86 defines a validated analytical procedure for the determination of lead bioaccessibility in contaminated soils. The method requires the use of a custom-fabricated extraction device that uses a heated water bath for ...

GS4 Molasses ICUMSA (International Commission for Uniform Methods in Sugar Analysis) Report

USDA-ARS?s Scientific Manuscript database

A report is given on international trade methods for molasses. At the present time there is a need to replace lead acetate clarification agent used in the determination of sucrose in molasses samples, in Europe and other parts of the world. The report discusses possible replacements for lead aceta...

Smoothed Two-Dimensional Edges for Laminar Flow

NASA Technical Reports Server (NTRS)

Holmes, B. J.; Liu, C. H.; Martin, G. L.; Domack, C. S.; Obara, C. J.; Hassan, A.; Gunzburger, M. D.; Nicolaides, R. A.

1986-01-01

New concept allows passive method for installing flaps, slats, iceprotection equipment, and other leading-edge devices on natural-laminar-flow (NLF) wings without causing loss of laminar flow. Two-dimensional roughness elements in laminar boundary layers strategically shaped to increase critical (allowable) height of roughness. Facilitates installation of leading-edge devices by practical manufacturing methods.

A novel assay method for the trace determination of Th and U in copper and lead using inductively coupled plasma mass spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaFerriere, Brian D.; Maiti, Tapas C.; Arnquist, Isaac J.

2015-03-01

This study describes a novel sample preparation and assay method developed in support of the MAJORANA DEMONSTRATOR experiment for the determination of thorium and uranium levels in copper and lead shielding components. Meticulously clean sample preparation methods combined with novel anion exchange separations for analyte pre-concentration and matrix removal were developed. Quantification was performed by inductively coupled plasma mass spectrometry. Detection limits of 0.0084 pg 232Th/g and 0.0106 pg 238U/g were determined for copper, while detection limits of 0.23 pg 232Th/g and 0.46 pg 238U/g were achieved for lead. These methods allow the Majorana Collaboration to accurately assay detector componentsmore » and ensure that the experiment’s stringent radiopurity requirements are met.« less

Effects of blood lead and cadmium levels on homocysteine level in plasma.

PubMed

Cai, R; Zheng, Y-F; Bu, J-G; Zhang, Y-Y; Fu, S-L; Wang, X-G; Guo, L-L; Zhang, J-R

2017-01-01

We studied the effect of non-occupational exposure to lead and cadmium on homocysteine level in plasma. Homocysteine is a marker for plasma folate folic acid metabolism in urban populations. 159 individuals from Beijing, Guangzhou, Shenzhen and Shanghai with no history of close exposure to heavy metals and no history of metabolic diseases were enrolled to participate in this study. Blood lead and cadmium levels were detected using ICP-MS method and the level of homocysteine was also measured using enzyme method. Our results showed that blood lead and cadmium levels in males were significantly higher than those in females. Also, blood lead and cadmium levels in smokers were higher than those in non-smokers; homocysteine level was significantly higher in smokers as well. According to blood lead and cadmium levels, cases were divided into four groups. Our results showed that a surge in blood lead and cadmium levels could result in an increase in homocysteine level. We concluded that in the Chinese population, smoking and gender might be the risk factors for elevated levels of lead and cadmium. Meanwhile, blood lead and cadmium levels may influence the homocysteine levels in the body. It is possible to speculate that non-occupational exposure to lead and cadmium, by increasing the homocysteine levels, negatively affect the cardiovascular and nervous system.

Performance of Dower's inverse transform and Frank lead system for Identification of Myocardial Infarction.

PubMed

Aranda, A; Bonizzi, P; Karel, J; Peeters, R

2015-08-01

This study performs a comparison between Dower's inverse transform and Frank lead system for Myocardial Infarction (MI) identification. We have selected a set of relevant features for MI detection from the vectorcardiogram and used the lasso method after that to build a model for the Dower's inverse transform and one for the Frank leads system. Then we analyzed the performance between both models on MI detection. The proposed methods have been tested using PhysioNet PTB database that contains 550 records from which 368 are MIs. Two main conclusions are coming from this study. The first one is that Dower's inverse transform performs equally well than Frank leads in identification of MI patients. The second one is that lead positions have a large influence on the accuracy of MI patient identification.

The Number of Recalled Leads is Highly Predictive of Lead Failure: Results From the Pacemaker and Implantable Defibrillator Leads Survival Study ("PAIDLESS").

PubMed

Kersten, Daniel J; Yi, Jinju; Feldman, Alyssa M; Brahmbhatt, Kunal; Asheld, Wilbur J; Germano, Joseph; Islam, Shahidul; Cohen, Todd J

2016-12-01

The purpose of this study was to determine if implantation of multiple recalled defibrillator leads is associated with an increased risk of lead failure. The authors of the Pacemaker and Implantable Defibrillator Leads Survival Study ("PAIDLESS") have previously reported a relationship between recalled lead status, lead failure, and patient mortality. This substudy analyzes the relationship in a smaller subset of patients who received more than one recalled lead. The specific effects of having one or more recalled leads have not been previously examined. This study analyzed lead failure and mortality of 3802 patients in PAIDLESS and compared outcomes with respect to the number of recalled leads received. PAIDLESS includes all patients at Winthrop University Hospital who underwent defibrillator lead implantation between February 1, 1996 and December 31, 2011. Patients with no recalled ICD leads, one recalled ICD lead, and two recalled ICD leads were compared using the Kaplan-Meier method and log-rank test. Sidak adjustment method was used to correct for multiple comparisons. All calculations were performed using SAS 9.4. P-values <.05 were considered statistically significant. This study included 4078 total ICD leads implanted during the trial period. There were 2400 leads (59%) in the no recalled leads category, 1620 leads (40%) in the one recalled lead category, and 58 leads (1%) in the two recalled leads category. No patient received more than two recalled leads. Of the leads categorized in the two recalled leads group, 12 experienced lead failures (21%), which was significantly higher (P<.001) than in the no recalled leads group (60 failures, 2.5%) and one recalled lead group (81 failures; 5%). Multivariable Cox's regression analysis found a total of six significant predictive variables for lead failure including the number of recalled leads (P<.001 for one and two recalled leads group). The number of recalled leads is highly predictive of lead failure. Lead-based multivariable Cox's regression analysis produced a total of six predictive variable categories for lead failure, one of which was the number of recalled leads. Kaplan-Meier analysis showed that the leads in the two recalled leads category failed faster than both the no recalled lead and one recalled lead groups. The greater the number of recalled leads to which patients are exposed, the greater the risk of lead failure.

Sparse Matrix for ECG Identification with Two-Lead Features.

PubMed

Tseng, Kuo-Kun; Luo, Jiao; Hegarty, Robert; Wang, Wenmin; Haiting, Dong

2015-01-01

Electrocardiograph (ECG) human identification has the potential to improve biometric security. However, improvements in ECG identification and feature extraction are required. Previous work has focused on single lead ECG signals. Our work proposes a new algorithm for human identification by mapping two-lead ECG signals onto a two-dimensional matrix then employing a sparse matrix method to process the matrix. And that is the first application of sparse matrix techniques for ECG identification. Moreover, the results of our experiments demonstrate the benefits of our approach over existing methods.

Two-Jet Rate in e+e- at Next-to-Next-to-Leading-Logarithmic Order

NASA Astrophysics Data System (ADS)

Banfi, Andrea; McAslan, Heather; Monni, Pier Francesco; Zanderighi, Giulia

2016-10-01

We present the first next-to-next-to-leading-logarithmic resummation for the two-jet rate in e+e- annihilation in the Durham and Cambridge algorithms. The results are obtained by extending the ares method to observables involving any global, recursively infrared and collinear safe jet algorithm in e+e- collisions. As opposed to other methods, this approach does not require a factorization theorem for the observables. We present predictions matched to next-to-next-to-leading order and a comparison to LEP data.

24 CFR 35.1310 - References.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint...) The HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing (Guidelines...

24 CFR 35.1310 - References.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint...) The HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing (Guidelines...

24 CFR 35.1310 - References.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint...) The HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing (Guidelines...

24 CFR 35.1310 - References.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint...) The HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing (Guidelines...

24 CFR 35.1310 - References.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint...) The HUD Guidelines for the Evaluation and Control of Lead-Based Paint Hazards in Housing (Guidelines...

Evaluation of landscape coverings to reduce soil lead hazards in urban residential yards: The Safer Yards Project.

PubMed

Binns, Helen J; Gray, Kimberly A; Chen, Tianyue; Finster, Mary E; Peneff, Nicholas; Schaefer, Peter; Ovsey, Victor; Fernandes, Joyce; Brown, Mavis; Dunlap, Barbara

2004-10-01

This study was designed primarily to evaluate the effectiveness of landscape coverings to reduce the potential for exposure to lead-contaminated soil in an urban neighborhood. Residential properties were randomized in to three groups: application of ground coverings/barriers plus placement of a raised garden bed (RB), application of ground coverings/barriers only (no raised bed, NRB), and control. Outcomes evaluated soil lead concentration (employing a weighting method to assess acute hazard soil lead [areas not fully covered] and potential hazard soil lead [all soil surfaces regardless of covering status]), density of landscape coverings (6 = heavy, > 90% covered; 1 = bare, < 10% covered), lead tracked onto carpeted entryway floor mats, and entryway floor dust lead loadings. Over 1 year, the intervention groups had significantly reduced acute hazard soil lead concentration (median change: RB, -478 ppm; NRB, -698 ppm; control, +52 ppm; Kruskal-Wallis, P = 0.02), enhanced landscape coverings (mean change in score: RB, +0.6; NRB, +1.5; control, -0.6; ANOVA, P < 0.001), and a 50% decrease in lead tracked onto the floor mats. The potential hazard soil lead concentration and the entryway floor dust lead loading did not change significantly. Techniques evaluated by this study are feasible for use by property owners but will require continued maintenance. The long-term sustainability of the method needs further examination.

Laboratory studies on the removal of radon-born lead from KamLAND's organic liquid scintillator

NASA Astrophysics Data System (ADS)

Keefer, G.; Grant, C.; Piepke, A.; Ebihara, T.; Ikeda, H.; Kishimoto, Y.; Kibe, Y.; Koseki, Y.; Ogawa, M.; Shirai, J.; Takeuchi, S.; Mauger, C.; Zhang, C.; Schweitzer, G.; Berger, B. E.; Dazeley, S.; Decowski, M. P.; Detwiler, J. A.; Djurcic, Z.; Dwyer, D. A.; Efremenko, Y.; Enomoto, S.; Freedman, S. J.; Fujikawa, B. K.; Furuno, K.; Gando, A.; Gando, Y.; Gratta, G.; Hatakeyama, S.; Heeger, K. M.; Hsu, L.; Ichimura, K.; Inoue, K.; Iwamoto, T.; Kamyshkov, Y.; Karwowski, H. J.; Koga, M.; Kozlov, A.; Lane, C. E.; Learned, J. G.; Maricic, J.; Markoff, D. M.; Matsuno, S.; McKee, D.; McKeown, R. D.; Miletic, T.; Mitsui, T.; Motoki, M.; Nakajima, Kyo; Nakajima, Kyohei; Nakamura, K.; O`Donnell, T.; Ogawa, H.; Piquemal, F.; Ricol, J.-S.; Shimizu, I.; Suekane, F.; Suzuki, A.; Svoboda, R.; Tajima, O.; Takemoto, Y.; Tamae, K.; Tolich, K.; Tornow, W.; Watanabe, Hideki; Watanabe, Hiroko; Winslow, L. A.; Yoshida, S.

2015-01-01

The removal of radioactivity from liquid scintillator has been studied in preparation of a low background phase of KamLAND. This paper describes the methods and techniques developed to measure and efficiently extract radon decay products from liquid scintillator. We report the radio-isotope reduction factors obtained when applying various extraction methods. During this study, distillation was identified as the most efficient method for removing radon-born lead from liquid scintillator.

Method development and subsequent survey analysis of biological tissues for platinum, lead, and manganese content.

PubMed Central

Yoakum, A M; Stewart, P L; Sterrett, J E

1975-01-01

An emission spectrochemical method is described for the determination of trace quantities of platinum, lead, and manganese in biological tissues. Total energy burns in an argon-oxygen atmosphere are employed. Sample preparation, conditions of analysis, and preparation of standards are discussed. The precision of the method is consistently better than +/- 15%, and comparative analyses indicate comparable accuracies. Data obtained for experimental rat tissues and for selected autopsy tissues are presented. PMID:1157798

Graphene oxide sheets immobilized polystyrene for column preconcentration and sensitive determination of lead by flame atomic absorption spectrometry.

PubMed

Islam, Aminul; Ahmad, Hilal; Zaidi, Noushi; Kumar, Suneel

2014-08-13

A novel solid-phase extractant was synthesized by coupling graphene oxide (GO) on chloromethylated polystyrene through an ethylenediamine spacer unit to develop a column method for the preconcentration/separation of lead prior to its determination by flame atomic absorption spectrometry. It was characterized by Fourier transform infrared spectroscopy, far-infrared spectroscopy, thermogravimetric analysis/differential thermal analysis, scanning electron microscopy, energy-dispersive spectrometry, and transmission electron microscopy. The abundant oxygen-containing surface functional groups form a strong complex with lead, resulting in higher sorption capacity (227.92 mg g(-1)) than other nanosorbents used for sorption studies of the column method. Using the column procedure here is an alternative to the direct use of GO, which restricts irreversible aggregation of GO and its escape into the ecosystem, making it an environmentally sustainable method. The column method was optimized by varying experimental variables such as pH, flow rate for sorption/desorption, and elution condition and was observed to exhibit a high preconcentration factor (400) with a low preconcentration limit (2.5 ppb) and a high degree of tolerance for matrix ions. The accuracy of the proposed method was verified by determining the Pb content in the standard reference materials and by recovery experiments. The method showed good precision with a relative standard deviation <5%. The proposed method was successfully applied for the determination of lead in tap water, electroplating wastewater, river water, and food samples after preconcentration.

Blood lead levels and cumulative blood lead index (CBLI) as predictors of late neurodevelopment in lead poisoned children

PubMed Central

Nie, Linda H.; Wright, Robert O.; Bellinger, David C.; Hussain, Javed; Amarasiriwardena, Chitra; Chettle, David R.; Pejović-Milić, Ana; woolf, Alan; Shannon, Michael

2011-01-01

Objective To find the best lead exposure assessment marker for children. Methods We recruited 11 children, calculated a cumulative blood lead index (CBLI) for the children, measured their concurrent BLL, assessed their development, and measured their bone lead level. Results Nine of 11 children had clinically significant neurodevelopment problems. CBLI and current blood lead level, but not the peak lead level, were significantly or marginally negatively associated with the full-scale IQ score. Conclusion Lead exposure at younger age significantly impacts a child’s later neurodevelopment. CBLI may be a better predictor of neurodevelopment than are current or peak blood lead levels. PMID:21827276

Thermoelectric materials and methods for synthesis thereof

DOEpatents

Ren, Zhifeng; Zhang, Qinyong; Zhang, Qian; Chen, Gang

2015-08-04

Materials having improved thermoelectric properties are disclosed. In some embodiments, lead telluride/selenide based materials with improved figure of merit and mechanical properties are disclosed. In some embodiments, the lead telluride/selenide based materials of the present disclosure are p-type thermoelectric materials formed by adding sodium (Na), silicon (Si) or both to thallium doped lead telluride materials. In some embodiments, the lead telluride/selenide based materials are formed by doping lead telluride/selenides with potassium.

Preparation of lead oxide nanoparticles from cathode-ray tube funnel glass by self-propagating method.

PubMed

Wang, Yu; Zhu, Jianxin

2012-05-15

This paper presents a novel process of extracting lead oxide nanoparticles from cathode-ray tube (CRT) funnel glass using self-propagating high-temperature synthesis (SHS) method. The impacts of added amount of funnel glass on the extraction ratio of lead, the lead extraction velocity and the micromorphology, as well as particle size of extracted nanoparticles were investigated. We found that self-propagating reaction in the presence of Mg and Fe(2)O(3) could separate lead preferentially and superfine lead oxide nanoparticles were obtained from a collecting chamber. The separation ratio was related closely to the amount of funnel glass added in the original mixture. At funnel glass addition of no more than 40wt.%, over 90wt.% of lead was recovered from funnel glass. High extraction yield reveals that the network structure of funnel glass was fractured due to the dramatic energy generated during the SHS melting process. The PbO nanoparticles collected show good dispersion and morphology with a mean grain size of 40-50nm. Copyright © 2012 Elsevier B.V. All rights reserved.

Simulation Analysis of Helicopter Ground Resonance Nonlinear Dynamics

NASA Astrophysics Data System (ADS)

Zhu, Yan; Lu, Yu-hui; Ling, Ai-min

2017-07-01

In order to accurately predict the dynamic instability of helicopter ground resonance, a modeling and simulation method of helicopter ground resonance considering nonlinear dynamic characteristics of components (rotor lead-lag damper, landing gear wheel and absorber) is presented. The numerical integral method is used to calculate the transient responses of the body and rotor, simulating some disturbance. To obtain quantitative instabilities, Fast Fourier Transform (FFT) is conducted to estimate the modal frequencies, and the mobile rectangular window method is employed in the predictions of the modal damping in terms of the response time history. Simulation results show that ground resonance simulation test can exactly lead up the blade lead-lag regressing mode frequency, and the modal damping obtained according to attenuation curves are close to the test results. The simulation test results are in accordance with the actual accident situation, and prove the correctness of the simulation method. This analysis method used for ground resonance simulation test can give out the results according with real helicopter engineering tests.

Total Arsenic, Cadmium, and Lead Determination in Brazilian Rice Samples Using ICP-MS

PubMed Central

Buzzo, Márcia Liane; de Arauz, Luciana Juncioni; Carvalho, Maria de Fátima Henriques; Arakaki, Edna Emy Kumagai; Matsuzaki, Richard; Tiglea, Paulo

2016-01-01

This study is aimed at investigating a suitable method for rice sample preparation as well as validating and applying the method for monitoring the concentration of total arsenic, cadmium, and lead in rice by using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). Various rice sample preparation procedures were evaluated. The analytical method was validated by measuring several parameters including limit of detection (LOD), limit of quantification (LOQ), linearity, relative bias, and repeatability. Regarding the sample preparation, recoveries of spiked samples were within the acceptable range from 89.3 to 98.2% for muffle furnace, 94.2 to 103.3% for heating block, 81.0 to 115.0% for hot plate, and 92.8 to 108.2% for microwave. Validation parameters showed that the method fits for its purpose, being the total arsenic, cadmium, and lead within the Brazilian Legislation limits. The method was applied for analyzing 37 rice samples (including polished, brown, and parboiled), consumed by the Brazilian population. The total arsenic, cadmium, and lead contents were lower than the established legislative values, except for total arsenic in one brown rice sample. This study indicated the need to establish monitoring programs for emphasizing the study on this type of cereal, aiming at promoting the Public Health. PMID:27766178

Lead-free 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 nanowires for energy harvesting.

PubMed

Zhou, Zhi; Bowland, Christopher C; Malakooti, Mohammad H; Tang, Haixiong; Sodano, Henry A

2016-03-07

Lead-free piezoelectric nanowires (NWs) show strong potential in sensing and energy harvesting applications due to their flexibility and ability to convert mechanical energy to electric energy. Currently, most lead-free piezoelectric NWs are produced through low yield synthesis methods and result in low electromechanical coupling, which limit their efficiency as energy harvesters. In order to alleviate these issues, a scalable method is developed to synthesize perovskite type 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 (BZT-BCT) NWs with high piezoelectric coupling coefficient. The piezoelectric coupling coefficient of the BZT-BCT NWs is measured by a refined piezoresponse force microscopy (PFM) testing method and shows the highest reported coupling coefficient for lead-free piezoelectric nanowires of 90 ± 5 pm V(-1). Flexible nanocomposites utilizing dispersed BZT-BCT NWs are fabricated to demonstrate an energy harvesting application with an open circuit voltage of up to 6.25 V and a power density of up to 2.25 μW cm(-3). The high electromechanical coupling coefficient and high power density demonstrated with these lead-free NWs produced via a scalable synthesis method shows the potential for high performance NW-based devices.

Impact analysis of leading sub sector on basic sector to regional income in Siak Regency, Riau Province

NASA Astrophysics Data System (ADS)

Astuti, P.; Nugraha, I.; Abdillah, F.

2018-02-01

During this time Siak regency only known as oil producing regency in Riau province, but based on the vision of spatial planning Siak’s regency in 2031 there was a shift from petroleum towards to other sectors such as agribusiness, agroindustry and tourism. The purpose of this study was to identify the sector base, the leading subsectors and shift with their characteristics and to identify the leading subsectors development priority. The method used in this research consisted of the method of Location Quotient (LQ, Shift Share, and Overlay method). The research results were used Location Quotient (LQ) to identify sector’s base in Siak regency based on the document of PDRB. The sector’s refers to the constant prices year of 2000 were mining and quarrying sector (2.25). The sector’s base using document of PDRB at constant prices 2000 without oil and gas sector was the agricultural sector with a value of LQ was 2,45. The leading sub sector in the Siak regency with mining and quarrying sector was oil and gas (1.02) and leading sub sector without oil and gas sector was the plantation sector (1.48) and forestry sector (1.73). Overlay analysis results shown that agriculture sector as a sector base and plantation and forestry as a leading sub sector has positive value and categorize as progressive and competitiveness. Because of that, this leading sub sector gets high priority to developing.

Lead Quantification in Urine Samples of Athletes by Coupling DLLME with UV-Vis Spectrophotometry.

PubMed

Faraji, Hakim; Helalizadeh, Masoumeh

2017-04-01

Urine lead level is one of the most employed measures of lead exposure and risk. The urine samples used in this study were obtained from ten healthy male cyclists. Dispersive liquid-liquid microextraction combined with ultraviolet and visible spectrophotometry was utilized for preconcentration, extraction, and determination of lead in urine samples. Optimization of the independent variables was carried out based on chemometric methods in three steps. According to the screening and optimization study, 133 μL of CCl 4 (extracting solvent), 1.34 mL ethanol (dispersing solvent), pH 2.0, 0.00 % of salt, and 0.1 % O,O-diethyl dithiophosphoric (chelating agent) were used as the optimum independent variables for microextraction and determination of lead. Under the optimized conditions, R 2 was 0.9991, and linearity range was 0.01-100 μg L -1 . Precision was evaluated in terms of repeatability and intermediate precision, with relative standard deviations being <9.1 and <15.3 %, respectively. The accuracy was estimated using urine samples of cyclists as real samples and it was confirmed. The relative error of ≤5 % was considered significant in the method specificity study. The lead concentration mean for the cyclists was 3.79 μg L -1 in urine samples. As a result, the proposed method is a robust technique to quantify lead concentrations higher than 11.6 ng L -1 in urine samples.

Infrared Spectroscopy Determination of Lead Binding to Ethylenediaminotetraacetic Acid

NASA Astrophysics Data System (ADS)

Fitch, Alanah; Dragan, Simona

1998-08-01

In an attempt to improve a thematic lab sequence based on lead analysis of community derived samples, we have considered infrared spectroscopy as a method of determining the lead bound to ethylenediaminotetraacetic acid (EDTA). Students get acquainted with infrared spectroscopy by interpreting the spectra of EDTA, disodium ethylenediaminotetraacetate (Na2EDTA) and of lead(II) ethylenediaminotetraacetate (PbEDTA). Spectral characterization of the above compounds in the 1800-1500 cm-1 region gives information about the structural changes that sodium and lead binding to EDTA, respectively, produce. The spectra show the carboxylic carbonyl absorption band shifted from 1697 cm-1 to 1633 cm-1 in Na2EDTA, and two distinctive absorption bands at 1697 cm-1 and 1558 cm-1 in PbEDTA, the former being attributed to the "free" carboxylic group, as in EDTA, and the latter to the coordinated carboxylate with the bond order of less than 1.5 between the carbon and oxygen atoms. These features led us to the conclusion that the divalent Pb is tetra-coordinated having two covalent metal-nitrogen bonds and two ionic metal-carboxylate bonds. Based on the spectral differences between PbEDTA and EDTA, we have developed a method to quantitate the amount of lead bound to EDTA by simply comparing the peak height of the most prominent peaks in the 1800-1550 cm-1 region. A potential application of this method could be determination of lead extracted by binding it to ethylenediaminotetraacetic acid, excess EDTA being added.

In situ click chemistry: a powerful means for lead discovery.

PubMed

Sharpless, K Barry; Manetsch, Roman

2006-11-01

Combinatorial chemistry and parallel synthesis are important and regularly applied tools for lead identification and optimisation, although they are often accompanied by challenges related to the efficiency of library synthesis and the purity of the compound library. In the last decade, novel means of lead discovery approaches have been investigated where the biological target is actively involved in the synthesis of its own inhibitory compound. These fragment-based approaches, also termed target-guided synthesis (TGS), show great promise in lead discovery applications by combining the synthesis and screening of libraries of low molecular weight compounds in a single step. Of all the TGS methods, the kinetically controlled variant is the least well known, but it has the potential to emerge as a reliable lead discovery method. The kinetically controlled TGS approach, termed in situ click chemistry, is discussed in this article.

Method and apparatus for diagnosis of lead toxicity

DOEpatents

Rosen, John F.; Slatkin, Daniel N.; Wielopolski, Lucian

1989-01-01

Improved methods and apparatus for in vivo measurement of the skeletal lead burden of a patient and for diagnosis of lead toxicity are disclosed. The apparatus comprises an x-ray tube emitting soft low energy x-rays from a silver anode, a polarizer for polarizing the emitted x-rays, and a detector for detecting photons fluoresced from atoms in the patient's tibia upon irradiation by the polarized x-rays. The fluoresced photons are spectrally analyzed to determine their energy distribution. Peaks indicating the presence of lead are identified if the patient has relatively high bone lead content. The data may be compared to data recorded with respect to a similar test performed on patients having also had the conventional EDTA chelation tests performed thereon in order to correlate the test results with respect to a particular patient to the conventionally accepted EDTA chelation test.

Polypyrrole/multi-walled carbon nanotube composite for the solid phase extraction of lead(II) in water samples.

PubMed

Sahmetlioglu, Ertugrul; Yilmaz, Erkan; Aktas, Ece; Soylak, Mustafa

2014-02-01

A multi-walled carbon nanotubes-polypyrrole conducting polymer nanocomposite has been synthesized, characterized and used for the separation and preconcentration of lead at trace levels in water samples prior to its flame atomic absorption spectrometric detection. The analytical parameters like pH, sample volume, eluent, sample flow rate that were affected the retentions of lead(II) on the new nanocomposite were optimized. Matrix effects were also investigated. Limit of detection and preconcentration factors were 1.1 µg L(-1) and 200, respectively. The adsorption capacity of the nanocomposite was 25.0mg lead(II) per gram composite. The validation of the method was checked by using SPS-WW2 Waste water Level 2 certified reference material. The method was applied to the determination of lead in water samples with satisfactory results. © 2013 Elsevier B.V. All rights reserved.

Method of preventing leakage of a fluid along and through an insulating jacket of a thermocouple

DOEpatents

Thermos, Anthony Constantine; Rahal, Fadi Elias

2002-01-01

A thermocouple assembly includes a thermocouple; a plurality of lead wires extending from the thermocouple; an insulating jacket extending along and enclosing the plurality of leads; and at least one internally sealed area within the insulating jacket to prevent fluid leakage along and within the insulating jacket. The invention also provides a method of preventing leakage of a fluid along and through an insulating jacket of a thermocouple including the steps of a) attaching a plurality of lead wires to a thermocouple; b) adding a heat sensitive pseudo-wire to extend along the plurality of lead wires; c) enclosing the lead wires and pseudo-wire inside an insulating jacket; d) locally heating axially spaced portions of the insulating jacket to a temperature which melts the pseudo-wire and fuses it with an interior surface of the jacket.

SOURCES OF VARIABILITY IN COLLECTION AND PREPARATION OF PAINT AND LEAD-COATING SAMPLES

EPA Science Inventory

Chronic exposure of children to lead can result in permanent physiologic impairment. Since surfaces coated with lead-containing paints and varnishes are potential sources of exposure, it is extremely important that reliable methods for sampling and analysis be available. The so...

CASE STUDIES IN THE INTEGRATED USE OF SCALE ANALYSES TO SOLVE LEAD PROBLEMS

EPA Science Inventory

All methods of controlling lead corrosion involve immobilizing lead into relatively insoluble compounds that deposit on the interior wall of water pipes. Many different solid phases can form under the disparate conditions that exist in distribution systems, which range in how the...

The Pollution Detectives, Part III: Roadside Lead Pollution.

ERIC Educational Resources Information Center

Sanderson, Phil

1989-01-01

Described is a simple test tube method developed lead analysis of samples of roadside soil. The relationship between the results and the traffic flow indicate car exhausts are the major source of lead pollution. Materials and procedures are detailed. An example of results is provided. (Author/CW)

Association of Lead Levels and Cerebral Palsy

PubMed Central

Bansal, Neha; Aggarwal, Anju; Faridi, M. M. A.; Sharma, Tusha; Baneerjee, B. D.

2017-01-01

Background: Cerebral palsy is a common motor disability in childhood. Raised lead levels affect cognition. Children with cerebral palsy may have raised lead levels, further impairing their residual cognitive motor and behavioral abilities. Environmental exposure and abnormal eating habits may lead to increased lead levels. Aims and Objectives: To measure blood lead levels in children with cerebral palsy and compare them with healthy neurologically normal children. To correlate blood lead levels with environmental factors. Material and Methods: Design: Prospective case-control study. Setting: Tertiary care hospital. Participants: Cases comprised 34 children with cerebral palsy, and controls comprised 34 neurologically normal, age- and sex-matched children. Methods: Clinical and demographic details were recorded as per proforma. Detailed environmental history was recorded to know the source of exposure to lead. These children were investigated and treated as per protocol. Venous blood was collected in ethylenediaminetetraacetic acid vials for analysis of blood lead levels. Lead levels were estimated by Schimadzu Flame AA-6800 (atomic absorption spectrophotometer). Data were analyzed using SPSS version 17. P < .05 was taken as significant. Results: Mean blood lead levels were 9.20 ± 8.31 µg/dL in cerebral palsy cases and 2.89 ± 3.04 µg/dL in their controls (P < .001). Among children with cerebral palsy, 19 (55.88%) children had blood lead levels ≥5 µg/dL. Lead levels in children with pica were 12.33 ± 10.02 µg/dL in comparison to children with no history of pica, 6.70 ± 4.60 µg/dL (P = .029). No correlation was found between hemoglobin and blood lead levels in cases and controls. Conclusion: In our study, blood lead levels are raised in children with cerebral palsy. However, further studies are required to show effects of raised levels in these children. PMID:28491920

Technical Status and Progress of Lead Recycling of Battery

NASA Astrophysics Data System (ADS)

Li, Wei-feng; Jiang, Li-hua; Zhan, Jing; Zhang, Chuan-fu

The characteristics of various components in waste lead acid battery are analyzed in this paper. The present status and the study progress situation in industry production and research field of recycling of waste lead acid battery and lead paste used broken-separation technology are introduced. The comparison of advantages and disadvantages in different industry processes is carried. The advantages of redox bath smelting of lead concentrate and lead paste are analyzed. The method of redox bath smelting will be a low-carbon, environmentally friendly and efficient processes of secondary lead production and can be intensive to desulfurize for high temperature pool.

A Least-Squares Commutator in the Iterative Subspace Method for Accelerating Self-Consistent Field Convergence.

PubMed

Li, Haichen; Yaron, David J

2016-11-08

A least-squares commutator in the iterative subspace (LCIIS) approach is explored for accelerating self-consistent field (SCF) calculations. LCIIS is similar to direct inversion of the iterative subspace (DIIS) methods in that the next iterate of the density matrix is obtained as a linear combination of past iterates. However, whereas DIIS methods find the linear combination by minimizing a sum of error vectors, LCIIS minimizes the Frobenius norm of the commutator between the density matrix and the Fock matrix. This minimization leads to a quartic problem that can be solved iteratively through a constrained Newton's method. The relationship between LCIIS and DIIS is discussed. Numerical experiments suggest that LCIIS leads to faster convergence than other SCF convergence accelerating methods in a statistically significant sense, and in a number of cases LCIIS leads to stable SCF solutions that are not found by other methods. The computational cost involved in solving the quartic minimization problem is small compared to the typical cost of SCF iterations and the approach is easily integrated into existing codes. LCIIS can therefore serve as a powerful addition to SCF convergence accelerating methods in computational quantum chemistry packages.

Power Series Approximation for the Correlation Kernel Leading to Kohn-Sham Methods Combining Accuracy, Computational Efficiency, and General Applicability

NASA Astrophysics Data System (ADS)

Erhard, Jannis; Bleiziffer, Patrick; Görling, Andreas

2016-09-01

A power series approximation for the correlation kernel of time-dependent density-functional theory is presented. Using this approximation in the adiabatic-connection fluctuation-dissipation (ACFD) theorem leads to a new family of Kohn-Sham methods. The new methods yield reaction energies and barriers of unprecedented accuracy and enable a treatment of static (strong) correlation with an accuracy of high-level multireference configuration interaction methods but are single-reference methods allowing for a black-box-like handling of static correlation. The new methods exhibit a better scaling of the computational effort with the system size than rivaling wave-function-based electronic structure methods. Moreover, the new methods do not suffer from the problem of singularities in response functions plaguing previous ACFD methods and therefore are applicable to any type of electronic system.

SU-E-P-20: Personnel Lead Apparel Integrity Inspection: Where We Are and What We Need?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, S; Zhang, J; Anaskevich, L

Purpose: In recent years, tremendous efforts have been devoted to radiation dose reduction, especially for patients who are directly exposed to primary radiation or receive radiopharmaceuticals. Limited efforts have been focused on those personnel who are exposed to secondary radiation while fulfilling their work responsibilities associated with diagnostic imaging and image-guided interventions. Occupational exposure is compounded in daily practice and can lead to a significant radiation dose over time. Personnel lead apparel is a well-accepted engineering control to protect healthcare workers when radiation is inevitable. The question is, do we have a nationally established program to protect personnel? This studymore » is to investigate the lead apparel inspection programs among the USA. Methods: A series of surveys of state regulations, the University Health System Consortium, and federal regulations and regulations determined by accrediting bodies were conducted. The surveys were used to determine the current status of lead apparel programs regarding integrity inspections. Based on the survey results, a thorough program was proposed accordingly. Results: Of 50 states, seventeen states and Washington D.C. require lead apparel integrity inspections within their state regulations. Eleven of these states specify that the inspection is required on an annual basis. Two of these states require lead apron integrity checks to be performed semi-annually. Eleven out of the two hundred academic medical centers surveyed responded. The results show that the method (visually vs. fluoroscopy) used to conduct lead apparel integrity checks differ greatly amongst healthcare organizations. The FDA, EPA, CRCPD and NCRP require lead apparel integrity checks. However, the level of policies is different. A standard program is not well established and clearly there is a lack of standardization. Conclusion: A program led by legislative (state or federal government) and with specific frequency, methods, tracking and criteria is needed to ensure the integrity of personnel lead apparel.« less

Effectiveness of the Preservation Protocol within the Environmental Protection Agency (EPA) Method 200.8 for Soluble and Particulate Lead Recovery in Drinking Water

EPA Science Inventory

Lead (Pb) is a toxic trace metal that is regulated in drinking water. The U.S. Environmental Protection Agency (USEPA) issued the Lead and Copper Rule (LCR), which defines the action level for lead at the tap as 0.015 mg/L. Researchers and drinking water utilities typically emplo...

The Dramatic Methods of Hans van Dam.

ERIC Educational Resources Information Center

van de Water, Manon

1994-01-01

Interprets for the American reader the untranslated dramatic methods of Hans van Dam, a leading drama theorist in the Netherlands. Discusses the functions of drama as a method, closed dramatic methods, open dramatic methods, and applying van Dam's methods. (SR)

Content of toxic and essential metals in recrystallized and washed table salt in Shiraz, Iran

PubMed Central

2014-01-01

Background Table salt is the most commonly used food additive. Since most of the salt consumed in Iran comes from mines, contamination with heavy metals is a health concern. The commonest salt purification method in Iran is washing with water. But recently, some industries have turned to recrystallization method. The present study aimed to determine the level of essential and non-essential heavy metals in the table salt refined with recrystallization and washing methods. Methods Thirty eight pre-packed salt samples were directly collected from retail market in Shiraz (22 samples refined with recrystallization method and 16 with washing method). The level of lead, cadmium, copper, zinc, nickel and cobalt was determined using Voltammetric method. Daily intakes of lead and cadmium as well as their weekly intakes were calculated. Results The levels of lead, cadmium, copper, zinc, nickel and cobalt in recrystallized samples were 0. 30 ± 0.26, 0.02 ± 0.02, 0.11 ± 0.06, 0.34 ± 0.22, 0.15 ± 0.19 and 0.008 ± 0.007 μg/g, respectively, and also 0.37 ± 0.27, 0.017 ± 0.021, 0.19 ± 0.18, 0.37 ± 0.20, 0.13 ± 0.23 and 0.037 ± 0.06 μg/g in washed salt samples. The calculated weekly intake of lead and cadmium was 0.216 and 0.014 μg/kg, respectively for the recrystallized and 0.2653 and 0.0119 μg/kg for the washed salts. Conclusion All values for toxic metals were lower than the permitted maximum for human consumption as prescribed by Codex and Institute of Standards and Industrial Research of Iran. Only 0.8652-1.0612% of lead and 0.17-0.2% of cadmium PTWIs are received via salt consumption weekly. PMID:24398299

Prevention of Pica, the Major Cause of Lead Poisoning in Children

ERIC Educational Resources Information Center

de la Burde, Brigitte; Reames, Betty

1973-01-01

Describes a study undertaken to establish a basis for various methods to combat the ingestion of plaster or paint containing lead by children from the lower socio-economic level. Stresses the need for the removal of substandard housing, case-finding, and early treatment of lead poisoning. (Author/SF)

Deriving the 12-Lead Electrocardiogram From Four Standard Leads Based on the Frank Torso Model

DTIC Science & Technology

2001-10-25

System The University of Aizu, Fukushima Prefecture, Japan Abstract – This paper proposes a lead method and a processing means for monitoring the 12...Performing Organization Name(s) and Address(es) The University of Aizu Graduate School of Information System Fukushima Prefecture, Japan Performing

24 CFR 35.1335 - Standard treatments.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1335 Standard treatments. Standard... § 35.1330, unless it is found not to be a soil-lead hazard in accordance with § 35.1320(b). (e) Safe...

24 CFR 35.1335 - Standard treatments.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1335 Standard treatments. Standard... § 35.1330, unless it is found not to be a soil-lead hazard in accordance with § 35.1320(b). (e) Safe...

24 CFR 35.1335 - Standard treatments.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1335 Standard treatments. Standard... § 35.1330, unless it is found not to be a soil-lead hazard in accordance with § 35.1320(b). (e) Safe...

24 CFR 35.1335 - Standard treatments.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1335 Standard treatments. Standard... § 35.1330, unless it is found not to be a soil-lead hazard in accordance with § 35.1320(b). (e) Safe...

40 CFR 300.420 - Remedial site evaluation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... section is to describe the methods, procedures, and criteria the lead agency shall use to collect data, as...) Remedial preliminary assessment. (1) The lead agency shall perform a remedial PA on all sites in CERCLIS as... indicates that a removal action may be warranted, the lead agency shall initiate removal evaluation pursuant...

40 CFR 300.420 - Remedial site evaluation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... section is to describe the methods, procedures, and criteria the lead agency shall use to collect data, as...) Remedial preliminary assessment. (1) The lead agency shall perform a remedial PA on all sites in CERCLIS as... indicates that a removal action may be warranted, the lead agency shall initiate removal evaluation pursuant...

PROVIDING SOLUTIONS FOR A BETTER TOMORROW: REDUCING THE RISKS ASSOCIATED WITH LEAD IN SOIL; URL:

EPA Science Inventory

This brief publication describes, in general language, the health risks associated with exposure to soil and dust contaminated with lead as well as an innovative method to immobilize lead contaminants in the soil (and thereby reduce the risk of exposure) at Superfund sites. Also ...

Stable lead isotopes reveal a natural source of high lead concentrations to gasoline-contaminated groundwater

USGS Publications Warehouse

Landmeyer, J.E.; Bradley, P.M.; Bullen, T.D.

2003-01-01

Concentrations of total lead as high as 1,600 ??g/L were detected in gasoline-contaminated and uncontaminated groundwater at three gasoline-release sites in South Carolina. Total lead concentrations were highest in turbid groundwater samples from gasoline-contaminated and uncontaminated wells, whereas lower turbidity groundwater samples (collected using low-flow methods) had lower total lead concentrations. Dissolved lead concentrations in all wells sampled, however, were less than 15 ??g total lead/L, the current United States Environmental Protection Agency (US EPA) maximum contaminant level (MCL). Because many total lead concentrations exceeded the MCL, the source of lead to the groundwater system at two of the three sites was investigated using a stable lead isotope ratio approach. Plots of the stable isotope ratios of lead (Pb) in groundwater as 207Pb/206Pb versus 208Pb/206Pb, and 208Pb/204Pb versus 206Pb/204Pb were similar to ratios characteristic of lead-based minerals in local rocks of the southeastern US, and were not similar to the stable lead isotopes ratios characteristic of distant lead ore deposits such as Broken Hill, Australia, used to produce tetraethyl lead in gasoline products prior to its phase-out and ban in the United States. Moreover, the isotopic composition of dissolved lead was equivalent to the isotopic composition of total lead in turbid samples collected from the same well, suggesting that the majority of the lead detected in the groundwater samples was associated with sediment particulates of indigenous aquifer material, rather than lead associated with spilled leaded gasoline. The results of this investigation indicate that (1) lead detected at some gasoline-release sites may be derived from the local aquifer material, rather than the gasoline release, and consequently may affect site-specific remediation goals; (2) non-low flow groundwater sampling methods, such as a disposable bailer, may result in turbid groundwater samples and high total lead concentrations, and; (3) stable lead isotopes can be used to clarify the source of lead detected above permissible levels in gasoline-contaminated groundwater systems.

A Framework for Widespread Replication of a Highly Spatially Resolved Childhood Lead Exposure Risk Model

PubMed Central

Kim, Dohyeong; Galeano, M. Alicia Overstreet; Hull, Andrew; Miranda, Marie Lynn

2008-01-01

Background Preventive approaches to childhood lead poisoning are critical for addressing this longstanding environmental health concern. Moreover, increasing evidence of cognitive effects of blood lead levels < 10 μg/dL highlights the need for improved exposure prevention interventions. Objectives Geographic information system–based childhood lead exposure risk models, especially if executed at highly resolved spatial scales, can help identify children most at risk of lead exposure, as well as prioritize and direct housing and health-protective intervention programs. However, developing highly resolved spatial data requires labor-and time-intensive geocoding and analytical processes. In this study we evaluated the benefit of increased effort spent geocoding in terms of improved performance of lead exposure risk models. Methods We constructed three childhood lead exposure risk models based on established methods but using different levels of geocoded data from blood lead surveillance, county tax assessors, and the 2000 U.S. Census for 18 counties in North Carolina. We used the results to predict lead exposure risk levels mapped at the individual tax parcel unit. Results The models performed well enough to identify high-risk areas for targeted intervention, even with a relatively low level of effort on geocoding. Conclusions This study demonstrates the feasibility of widespread replication of highly spatially resolved childhood lead exposure risk models. The models guide resource-constrained local health and housing departments and community-based organizations on how best to expend their efforts in preventing and mitigating lead exposure risk in their communities. PMID:19079729

A Three-Dimensional Solution of Flows over Wings with Leading-Edge Vortex Separation. Part 1: Engineering Document

NASA Technical Reports Server (NTRS)

Brune, G. W.; Weber, J. A.; Johnson, F. T.; Lu, P.; Rubbert, P. E.

1975-01-01

A method of predicting forces, moments, and detailed surface pressures on thin, sharp-edged wings with leading-edge vortex separation in incompressible flow is presented. The method employs an inviscid flow model in which the wing and the rolled-up vortex sheets are represented by piecewise, continuous quadratic doublet sheet distributions. The Kutta condition is imposed on all wing edges. Computed results are compared with experimental data and with the predictions of the leading-edge suction analogy for a selected number of wing planforms over a wide range of angle of attack. These comparisons show the method to be very promising, capable of producing not only force predictions, but also accurate predictions of detailed surface pressure distributions, loads, and moments.

Presence of lead in paint of toys sold in stores of the formal market of Bogotá, Colombia.

PubMed

Mateus-García, A; Ramos-Bonilla, J P

2014-01-01

Lead (Pb) is a non-essential metal. Exposure to lead has been associated with adverse health effects in both children and adults. Lead content in paint used in toys or children's products has been identified as both a potential and preventable source of childhood lead exposure. Twenty-four stores located in Bogotá (Colombia) were selected by cluster sampling to participate in the study. A random sample of 96 toys was purchased at these stores. Since one toy can have different paint colors, a total of 116 paint samples from 96 toys were analyzed for lead content. Paint samples were prepared by microwave digestion and lead was quantified using ICP-OES. For quality control purposes of the analytical method, spike samples and a certified reference material (NIST SRM 2582) were used. The lead content in paint ranged from below the method detection limit (5ppm) to 47,600ppm, with an average Pb concentration of 1024ppm and a median concentration of 5ppm. Eight (8) paint samples removed from five toys had lead concentrations exceeding the US regulatory limit for total lead content (90ppm). Brown paint and toys manufactured in Colombia were significantly associated with high concentrations of lead in paint. Furthermore, a statistically significant interaction between these two variables was also found. The results suggest that there is a potential risk of lead exposure from paint of toys sold in the formal market of Bogotá. Therefore, the implementation of a national surveillance program of lead content in children products is urgently needed. The risk of children's lead exposure identified in this study, which is completely preventable, could be present also in other developing countries. © 2013 Published by Elsevier Inc.

Heavy metals in soil at a waste electrical and electronic equipment processing area in China.

PubMed

Gu, Weihua; Bai, Jianfeng; Yao, Haiyan; Zhao, Jing; Zhuang, Xuning; Huang, Qing; Zhang, Chenglong; Wang, JingWei

2017-11-01

For the objective of evaluating the contamination degree of heavy metals and analysing its variation trend in soil at a waste electrical and electronic equipment processing area in Shanghai, China, evaluation methods, which include single factor index method, geo-accumulation index method, comprehensive pollution index method, and potential ecological risk index method, were adopted in this study. The results revealed that the soil at a waste electrical and electronic equipment processing area was polluted by arsenic, cadmium, copper, lead, zinc, and chromium. It also demonstrated that the concentrations of heavy metals were increased over time. Exceptionally, the average value of the metalloid (arsenic) was 73.31 mg kg -1 in 2014, while it was 58.31 mg kg -1 in the first half of 2015, and it was 2.93 times and 2.33 times higher than that of the Chinese Environmental Quality Standard for Soil in 2014 and the first half of 2015, respectively. The sequences of the contamination degree of heavy metals in 2014 and the first half of 2015 were cadmium > lead > copper > chromium > zinc and cadmium > lead > chromium > zinc > copper. From the analysis of the potential ecological risk index method, arsenic and cadmium had higher ecological risk than other heavy metals. The integrated ecological risk index of heavy metals (cadmium, copper, lead, zinc, and chromium) and metalloid (arsenic) was 394.10 in 2014, while it was 656.16 in the first half of 2015, thus documenting a strong ecological risk.

[Use of blood lead data to evaluate and prevent childhood lead poisoning in Latin America].

PubMed

Romieu, Isabelle

2003-01-01

Exposure to lead is a widespread and serious threat to the health of children in Latin America. Health officials should monitor sources of exposure and health outcomes to design, implement, and evaluate prevention and control activities. To evaluate the magnitude of lead as a public health problem, three key elements must be defined: I) the potential sources of exposure, 2) the indicators to evaluate health effects and environmental exposure, and 3) the sampling methods for the population at risk. Several strategies can be used to select the study population depending on the study objectives, the time limitations, and the available resources. If the objective is to evaluate the magnitude and sources of the problem, the following sampling methods can be used: I) population-based random sampling; 2) facility-based random sampling within hospitals, daycare centers, or schools; 3) target sampling of high risk groups; 4) convenience sampling of volunteers; and 5) case reporting (which can lead to the identification of populations at risk and sources of exposures). For all sampling methods, information gathering should include the use of a questionnaire to collect general information on the participants and on potential local sources of exposure, as well as the collection of biological samples. In interpreting data, one should consider the type of sampling used and the non-response rates, as well as factors that might influence blood lead measurements, such as age and seasonal variability. Blood lead measurements should be integrated in an overall strategy to prevent lead toxicity in children. The English version of this paper is available at: http://www.insp.mx/salud/index.html.

Some aspects of using ultrasounds to improve sulfurous mineral flotation technology

NASA Technical Reports Server (NTRS)

Mihu, V. P.; Pop, I.

1974-01-01

The results are discussed which were obtained with a new method of desorption of collector reagents connected with improving the selectivity of the flotation of copper and lead concentrate through the action of ultrasounds. Analysis of the results obtained by treating copper and lead concentrate in an ultraacoustic field indicates an increase in the copper content of the copper concentrate, of the lead content in the lead concentrate and, at the same time, a reduction in the lead of the copper concentrate.

24 CFR 35.1300 - Purpose and applicability.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1300 Purpose and applicability. The...

24 CFR 35.1300 - Purpose and applicability.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1300 Purpose and applicability. The...

24 CFR 35.1300 - Purpose and applicability.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1300 Purpose and applicability. The...

24 CFR 35.1300 - Purpose and applicability.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1300 Purpose and applicability. The...

24 CFR 35.1300 - Purpose and applicability.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1300 Purpose and applicability. The...

[Determination of lead in edible salt with solid-phase extraction and GFAAS].

PubMed

Zhao, Xin; Zhou, Shuang; Ma, Lan; Yang, Dajin

2013-01-01

Establishing a method for determination of lead in salt with solid-phase extraction and GFAAS. Salt sample was diluted to a certain volume directly with ammonium acetate, then the sample solution was filtered through the solid phase extraction column which has been pre-activated. Lead ions were retained, and the sodium chloride matrix was removed. After elution, the collected lead ions was determined by graphite furnace atomic absorption spectrometry in 257.4 nm. This method can be used effectively to wipe off the sodium chloride in matrix. The limit of detection was 0.7 microg/kg and the limit of quantification was 2 microg/kg. Solid phase extraction technique can be used effectively to reduce the interference in matrix and improves the accuracy and reproducibility of detection.

The Enumeration Structure of 爾雅 Ěryǎ's "Semantic Lists"

NASA Astrophysics Data System (ADS)

Teboul (戴明德), Michel

Modern linguistic enumeration theory is applied to a study of 爾雅 Ěryǎ's Semantic Lists, leading to an in-depth analysis of the work's first three sections without any recourse to the traditional methods of Chinese classical philology. It is hoped that an extension of the same method can lead to a better understanding of the remaining 16 sections.

Integrated circuit package with lead structure and method of preparing the same

NASA Technical Reports Server (NTRS)

Kennedy, B. W. (Inventor)

1973-01-01

A beam-lead integrated circuit package assembly including a beam-lead integrated circuit chip, a lead frame array bonded to projecting fingers of the chip, a rubber potting compound disposed around the chip, and an encapsulating molded plastic is described. The lead frame array is prepared by photographically printing a lead pattern on a base metal sheet, selectively etching to remove metal between leads, and plating with gold. Joining of the chip to the lead frame array is carried out by thermocompression bonding of mating goldplated surfaces. A small amount of silicone rubber is then applied to cover the chip and bonded joints, and the package is encapsulated with epoxy resin, applied by molding.

The astonishingly holistic role of urban soil in the exposure of children to lead.

NASA Astrophysics Data System (ADS)

Mielke, Howard; Gonzales, Christopher; Powell, Eric

2017-04-01

The long-term resilience and sustainability of urban communities is associated with its environmental quality. One major impediment to community welfare is children's exposure to lead because it is a root cause of disparity and chronic conditions including health, learning, and behavioral differences. There is no safe level of lead exposure and this revelation is confounded by the lack of an effective intervention after exposure takes place. In August, 2005, Hurricane Katrina flooded 80% of New Orleans. This report explores the natural experiment of the dynamic changes of soil and children's blood lead in New Orleans before and ten years after the flood. Matched pre- and post-Hurricane soil lead and children's blood lead results were stratified by 172 communities of New Orleans. GIS methods were used to organize, describe, and map the pre- and post-Katrina data. Comparing pre- and post-Katrina results, simultaneous decreases occurred in soil lead and children's blood lead response. Health and welfare disparities continue to exist between environments and children's exposure living in interior compared with outer communities of the city. At the scale of a city this investigation demonstrates that declining soil lead effectively reduces children's blood lead. The astonishingly holistic role of soil relates to its position as a lead dust deposition reservoir and, at the same time, as an open source of ingestible and inhalable lead dust. Decreasing the soil lead on play areas of urban communities is beneficial and economical as a method for effective lead intervention and primary prevention. References Mielke, H.W.; Gonzales, C.R.; Powell, E.T.; Mielke, P.W. Jr. Spatiotemporal dynamic transformations of soil lead and children's blood lead ten years after Hurricane Katrina: New grounds for primary prevention. Environ. Int. 2016, DOI: 10.1016/j.envint.2016.06.017. Mielke, H.W.; Gonzales, C.R.; Powell, E.T. In review. The dynamic lead exposome and children's health in New Orleans pre-and post-Hurricane Katrina. Int. J. Environ. Res. Public Health

[Fragment-based drug discovery: concept and aim].

PubMed

Tanaka, Daisuke

2010-03-01

Fragment-Based Drug Discovery (FBDD) has been recognized as a newly emerging lead discovery methodology that involves biophysical fragment screening and chemistry-driven fragment-to-lead stages. Although fragments, defined as structurally simple and small compounds (typically <300 Da), have not been employed in conventional high-throughput screening (HTS), the recent significant progress in the biophysical screening methods enables fragment screening at a practical level. The intention of FBDD primarily turns our attention to weakly but specifically binding fragments (hit fragments) as the starting point of medicinal chemistry. Hit fragments are then promoted to more potent lead compounds through linking or merging with another hit fragment and/or attaching functional groups. Another positive aspect of FBDD is ligand efficiency. Ligand efficiency is a useful guide in screening hit selection and hit-to-lead phases to achieve lead-likeness. Owing to these features, a number of successful applications of FBDD to "undruggable targets" (where HTS and other lead identification methods failed to identify useful lead compounds) have been reported. As a result, FBDD is now expected to complement more conventional methodologies. This review, as an introduction of the following articles, will summarize the fundamental concepts of FBDD and will discuss its advantages over other conventional drug discovery approaches.

A comparison of alternative variants of the lead and lag time TTO.

PubMed

Devlin, Nancy; Buckingham, Ken; Shah, Koonal; Tsuchiya, Aki; Tilling, Carl; Wilkinson, Grahame; van Hout, Ben

2013-05-01

'Lead Time' TTO improves upon conventional TTO by providing a uniform method for eliciting positive and negative values. This research investigates (i) the values generated from different combinations of time in poor health and in full health; and the order in which these appear (lead vs. lag); (ii) whether values concur with participants' views about states; (iii) methods for handling extreme preferences. n = 208 participants valued five EQ-5D states, using two of four variants. Combinations of lead time and health state duration were: 10 years and 20 years; 5 years and 1 year; 5 years and 10 years; and a health state duration of 5 years with a lag time of 10 years. Longer lead times capture more preferences, but may involve a framing effect. Lag time results in less non-trading for mild states, and less time being traded for severe states. Negative values broadly agree with participants' stated opinion that the state is worse than dead. The values are sensitive to the ratio of lead time to duration of poor health, and the order in which these appear (lead vs. lag). It is feasible to handle extreme preferences though challenges remain. Copyright © 2012 John Wiley & Sons, Ltd.

Symmetric airfoil geometry effects on leading edge noise.

PubMed

Gill, James; Zhang, X; Joseph, P

2013-10-01

Computational aeroacoustic methods are applied to the modeling of noise due to interactions between gusts and the leading edge of real symmetric airfoils. Single frequency harmonic gusts are interacted with various airfoil geometries at zero angle of attack. The effects of airfoil thickness and leading edge radius on noise are investigated systematically and independently for the first time, at higher frequencies than previously used in computational methods. Increases in both leading edge radius and thickness are found to reduce the predicted noise. This noise reduction effect becomes greater with increasing frequency and Mach number. The dominant noise reduction mechanism for airfoils with real geometry is found to be related to the leading edge stagnation region. It is shown that accurate leading edge noise predictions can be made when assuming an inviscid meanflow, but that it is not valid to assume a uniform meanflow. Analytic flat plate predictions are found to over-predict the noise due to a NACA 0002 airfoil by up to 3 dB at high frequencies. The accuracy of analytic flat plate solutions can be expected to decrease with increasing airfoil thickness, leading edge radius, gust frequency, and Mach number.

SU-F-I-71: Fetal Protection During Fluoroscopy: To Shield Or Not to Shield?

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, S; Vanderhoek, M

Purpose: Lead aprons are routinely used to shield the fetus from radiation during fluoroscopically guided interventions (FGI) involving pregnant patients. When placed in the primary beam, lead aprons often reduce image quality and increase fluoroscopic radiation output, which can adversely affect fetal dose. The purpose of this work is to identify an effective and practical method to reduce fetal dose without affecting image quality. Methods: A pregnant patient equivalent abdominal phantom is set on the table along with an image quality test object (CIRS model 903) representing patient anatomy of interest. An ion chamber is positioned at the x-ray beammore » entrance to the phantom, which is used to estimate the relative fetal dose. For three protective methods, image quality and fetal dose measurements are compared to baseline (no protection):1. Lead apron shielding the entire abdomen; 2. Lead apron shielding part of the abdomen, including the fetus; 3. Narrow collimation such that fetus is excluded from the primary beam. Results: With lead shielding the entire abdomen, the dose is reduced by 80% relative to baseline along with a drastic deterioration of image quality. With lead shielding only the fetus, the dose is reduced by 65% along with complete preservation of image quality, since the image quality test object is not shielded. However, narrow collimation results in 90% dose reduction and a slight improvement of image quality relative to baseline. Conclusion: The use of narrow collimation to protect the fetus during FGI is a simple and highly effective method that simultaneously reduces fetal dose and maintains sufficient image quality. Lead aprons are not as effective at fetal dose reduction, and if placed improperly, they can severely degrade image quality. Future work aims to investigate a wider variety of fluoroscopy systems to confirm these results across many different system geometries.« less

24 CFR 35.1305 - Definitions and other general requirements.

Code of Federal Regulations, 2011 CFR

2011-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1305...

24 CFR 35.1305 - Definitions and other general requirements.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1305...

24 CFR 35.1305 - Definitions and other general requirements.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1305...

24 CFR 35.1305 - Definitions and other general requirements.

Code of Federal Regulations, 2010 CFR

2010-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1305...

24 CFR 35.1305 - Definitions and other general requirements.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1305...

Changes in Blood Lead Levels Associated with Use of Chloramines in Water Treatment Systems

PubMed Central

Miranda, Marie Lynn; Kim, Dohyeong; Hull, Andrew P.; Paul, Christopher J.; Galeano, M. Alicia Overstreet

2007-01-01

Background More municipal water treatment plants are using chloramines as a disinfectant in order to reduce carcinogenic by-products. In some instances, this has coincided with an increase in lead levels in drinking water in those systems. Lead in drinking water can be a significant health risk. Objectives We sought to test the potential effect of switching to chloramines for disinfection in water treatment systems on childhood blood lead levels using data from Wayne County, located in the central Coastal Plain of North Carolina. Methods We constructed a unified geographic information system (GIS) that links blood lead screening data with age of housing, drinking water source, and census data for 7,270 records. The data were analyzed using both exploratory methods and more formal multivariate techniques. Results The analysis indicates that the change to chloramine disinfection may lead to an increase in blood lead levels, the impact of which is progressively mitigated in newer housing. Conclusions Introducing chloramines to reduce carcinogenic by-products may increase exposure to lead in drinking water. Our research provides guidance on adjustments in the local childhood lead poisoning prevention program that should accompany changes in water treatment. As similar research is conducted in other areas, and the underlying environmental chemistry is clarified, water treatment strategies can be optimized across the multiple objectives that municipalities face in providing high quality drinking water to local residents. PMID:17384768

Library design practices for success in lead generation with small molecule libraries.

PubMed

Goodnow, R A; Guba, W; Haap, W

2003-11-01

The generation of novel structures amenable to rapid and efficient lead optimization comprises an emerging strategy for success in modern drug discovery. Small molecule libraries of sufficient size and diversity to increase the chances of discovery of novel structures make the high throughput synthesis approach the method of choice for lead generation. Despite an industry trend for smaller, more focused libraries, the need to generate novel lead structures makes larger libraries a necessary strategy. For libraries of a several thousand or more members, solid phase synthesis approaches are the most suitable. While the technology and chemistry necessary for small molecule library synthesis continue to advance, success in lead generation requires rigorous consideration in the library design process to ensure the synthesis of molecules possessing the proper characteristics for subsequent lead optimization. Without proper selection of library templates and building blocks, solid phase synthesis methods often generate molecules which are too heavy, too lipophilic and too complex to be useful for lead optimization. The appropriate filtering of virtual library designs with multiple computational tools allows the generation of information-rich libraries within a drug-like molecular property space. An understanding of the hit-to-lead process provides a practical guide to molecular design characteristics. Examples of leads generated from library approaches also provide a benchmarking of successes as well as aspects for continued development of library design practices.

Indirect lead exposure among children of radiator repair workers.

PubMed

Aguilar-Garduño, C; Lacasaña, M; Tellez-Rojo, M M; Aguilar-Madrid, G; Sanin-Aguirre, L H; Romieu, I; Hernandez-Avila, M

2003-06-01

Secondary exposure to lead has been identified as a public health problem since the late 1940s; we investigate the risk of lead exposure among families of radiator repair workers. A sample of the wives and children, aged 6 months to 6 years (exposed children) (n = 19), of radiator repair workers and a sample of children whose parents were not occupationally exposed to lead (non-exposed children) (n = 29) were matched for age and residence; their geometric mean blood lead levels are compared. Blood samples were obtained by the finger stick method and environmental dust samples by the wipe method; both were analyzed using a portable anodic stripping voltameter. Dust lead levels were significantly higher in the houses of exposed children (143.8 vs. 3.9 microg/g; P < 0.01). In crude analyses, the highest lead levels were observed among children whose fathers worked in home-based workshops (22.4 microg/dl)(n = 6). Children whose fathers worked in an external workshop (n = 13) also had high levels (14.2 microg/dl) (P < 0.01), while blood lead levels in non-exposed children were significantly lower (5.6 microg/dl)(P < 0.01). The observed differences remained significant after adjustment for age and gender. This study confirms that children of radiator repair workers are at increased risk of lead exposure and public health interventions are needed to protect them. Copyright 2003 Wiley-Liss, Inc.

Spectrophotometric studies on the complexation equilibria of Ni and Pb with 2-carboxy-2-hydroxy-5'-sulfo-formazylbenzene. Simultaneous determination of trace amounts of Ni and Pb.

PubMed

Hashem, Elham Y; Abu-Bakr, Mohamed S; Hussain, Sawsan M

2004-01-01

Spectrophotometric studies have been made to investigate the reaction of Nickel and Lead with 2-carboxy-2'-hydroxy-5'-sulfoformazyl-benzene (zincon) in 50%(v/v) ethanol-water at 25 degrees C and an ionic strength of 0.1 M NaClO4. A complete picture of the complexation equilibria in the pH range (4.2-12.0) for nickel and (1.9-11.5) for lead are presented. Simple, rapid, selective and sensitive methods for the spectro-photometric determination of nickel and lead has been developed based on the color reaction of their complexes with zincon. The methods allow the determination of 4.69 microg mL(-1) of nickel at pH = 6.3 (lambdamax = 665 nm) and 10.3 microg ml(-1) of lead at pH = 5.6 (lambdamax = 610 nm). The apparent molar absorptivities were epsilon = 1.3 x 10(4) L mol(-1) cm(-1) for nickel and epsilon = 0.6 x 10(4) L mol(-1) cm(-1) for lead. The interference of a large number of foreign ions and complexing agents has been studied. Thiosulphate, as masking agent allows the simultaneous determination of nickel and lead in the presence of high concentrations of copper. Ascorbic acid, sodium cyanide and or sodium fluoride provide the elimination of many other interferences. The methods have been applied successfully to the simultaneous determination of nickel and lead in an aluminium and non-ferrous alloy.

Lead with Passion: Effective Leadership Characteristics as Perceived by School Administrators and Teachers

ERIC Educational Resources Information Center

Manuel, La Tanya Antoinette

2017-01-01

The purpose of this mixed methods research study was to examine how educators lead with passion. The study identified key characteristics in school administrators and teachers who lead effective schools. This research study analyzed whether there were any significant differences in the leadership styles of administrators and teachers. Five…

Hybrid Ultra-Low VOC and Non-HAP Rain Erosion Coatings

DTIC Science & Technology

2018-01-12

cavitation test stand for running the modified ASTM G32 method...Objective Numerous military aircraft and shipboard surfaces, such as radomes, antennas, gun shields, wing leading edges, and helicopter blade leading edges... blades , and helicopter blade leading edges. The application market is extremely widespread. Luna will leverage existing internal contacts for

Field Turbidity Methods for the Determination of Lead in Acid Extracts of Dried Paint

EPA Science Inventory

Lead, which can be found in old paint, soil, and dust, has been clearly shown to have adverse health effects on the neurological systems of both children and adults. As part of an ongoing effort to reduce childhood lead poisoning, the U.S. Environmental Protection Agency promulga...

Analysis and Development of Finite Element Methods for the Study of Nonlinear Thermomechanical Behavior of Structural Components

NASA Technical Reports Server (NTRS)

Oden, J. Tinsley

1995-01-01

Underintegrated methods are investigated with respect to their stability and convergence properties. The focus was on identifying regions where they work and regions where techniques such as hourglass viscosity and hourglass control can be used. Results obtained show that underintegrated methods typically lead to finite element stiffness with spurious modes in the solution. However, problems exist (scalar elliptic boundary value problems) where underintegrated with hourglass control yield convergent solutions. Also, stress averaging in underintegrated stiffness calculations does not necessarily lead to stable or convergent stress states.

Low-level lead exposure and the IQ of children. A meta-analysis of modern studies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Needleman, H.L.; Gatsonis, C.A.

1990-02-02

We identified 24 modern studies of childhood exposures to lead in relation to IQ. From this population, 12 that employed multiple regression analysis with IQ as the dependent variable and lead as the main effect and that controlled for nonlead covariates were selected for a quantitative, integrated review or meta-analysis. The studies were grouped according to type of tissue analyzed for lead. There were 7 blood and 5 tooth lead studies. Within each group, we obtained joint P values by two different methods and average effect sizes as measured by the partial correlation coefficients. We also investigated the sensitivity ofmore » the results to any single study. The sample sizes ranged from 75 to 724. The sign of the regression coefficient for lead was negative in 11 of 12 studies. The negative partial r's for lead ranged from -.27 to -.003. The power to find an effect was limited, below 0.6 in 7 of 12 studies. The joint P values for the blood lead studies were less than .0001 for both methods of analysis (95% confidence interval for group partial r, -.15 {plus minus} .05), while for the tooth lead studies they were .0005 and .004, respectively (95% confidence interval for group partial r, -.08 {plus minus} .05). The hypothesis that lead impairs children's IQ at low dose is strongly supported by this quantitative review. The effect is robust to the impact of any single study.« less

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Burnside, Walter D.

1989-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameter is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

A method to design blended rolled edges for compact range reflectors

NASA Technical Reports Server (NTRS)

Gupta, Inder J.; Ericksen, Kurt P.; Burnside, Walter D.

1990-01-01

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameters is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Creating the learning situation to promote student deep learning: Data analysis and application case

NASA Astrophysics Data System (ADS)

Guo, Yuanyuan; Wu, Shaoyan

2017-05-01

How to lead students to deeper learning and cultivate engineering innovative talents need to be studied for higher engineering education. In this study, through the survey data analysis and theoretical research, we discuss the correlation of teaching methods, learning motivation, and learning methods. In this research, we find that students have different motivation orientation according to the perception of teaching methods in the process of engineering education, and this affects their choice of learning methods. As a result, creating situations is critical to lead students to deeper learning. Finally, we analyze the process of learning situational creation in the teaching process of «bidding and contract management workshops». In this creation process, teachers use the student-centered teaching to lead students to deeper study. Through the study of influence factors of deep learning process, and building the teaching situation for the purpose of promoting deep learning, this thesis provide a meaningful reference for enhancing students' learning quality, teachers' teaching quality and the quality of innovation talent.

Low temperature synthesis & characterization of lead-free BCZT ceramics using molten salt method

NASA Astrophysics Data System (ADS)

Jai Shree, K.; Chandrakala, E.; Das, Dibakar

2018-04-01

Piezoelectric properties are greatly influenced by the synthesis route, microstructure, stoichiometry of the chemical composition, purity of the starting materials. In this study, molten salt method was used to prepare lead-free BCZT ceramics. Molten salt method is one of the simplestmethods to prepare chemically-purified, single phase powders in high yield often at lower temperatures and shorten reaction time. Calcination of the molten salt synthesized powders resulted in asingle-phase perovskite structure at 1000 °C which is ˜ 350 °C less than the conventional solid-sate reaction method. With increasing calcination temperature the average template size was increased (˜ 0.5-2 µm). Formation of well dispersive templates improves the sinterability at lower temperatures. Lead-free BCZT ceramics sintered at 1500 °C for 2 h resulted in homogenous and highly dense microstructure with ˜92% of the theoretical density and a grain size of ˜ 35 µm. This highly dense microstructure could enhance the piezoelectric properties of the system.

Method and System for Weakening Shock Wave Strength at Leading Edge Surfaces of Vehicle in Supersonic Atmospheric Flight

NASA Technical Reports Server (NTRS)

Pritchett, Victor E., II (Inventor); Wang, Ten-See (Inventor); Blankson, Isaiah M. (Inventor); Daso, Endwell O. (Inventor); Farr, Rebecca Ann (Inventor); Auslender, Aaron Howard (Inventor); Plotkin, Kenneth J. (Inventor)

2015-01-01

A method and system are provided to weaken shock wave strength at leading edge surfaces of a vehicle in atmospheric flight. One or more flight-related attribute sensed along a vehicle's outer mold line are used to control the injection of a non-heated, non-plasma-producing gas into a local external flowfield of the vehicle from at least one leading-edge surface location along the vehicle's outer mold line. Pressure and/or mass flow rate of the gas so-injected is adjusted in order to cause a Rankine-Hugoniot Jump Condition along the vehicle's outer mold line to be violated.

The lead-lag relationship between stock index and stock index futures: A thermal optimal path method

NASA Astrophysics Data System (ADS)

Gong, Chen-Chen; Ji, Shen-Dan; Su, Li-Ling; Li, Sai-Ping; Ren, Fei

2016-02-01

The study of lead-lag relationship between stock index and stock index futures is of great importance for its wide application in hedging and portfolio investments. Previous works mainly use conventional methods like Granger causality test, GARCH model and error correction model, and focus on the causality relation between the index and futures in a certain period. By using a non-parametric approach-thermal optimal path (TOP) method, we study the lead-lag relationship between China Securities Index 300 (CSI 300), Hang Seng Index (HSI), Standard and Poor 500 (S&P 500) Index and their associated futures to reveal the variance of their relationship over time. Our finding shows evidence of pronounced futures leadership for well established index futures, namely HSI and S&P 500 index futures, while index of developing market like CSI 300 has pronounced leadership. We offer an explanation based on the measure of an indicator which quantifies the differences between spot and futures prices for the surge of lead-lag function. Our results provide new perspectives for the understanding of the dynamical evolution of lead-lag relationship between stock index and stock index futures, which is valuable for the study of market efficiency and its applications.

The study of lead vapor ionization in discharge with a hot cathode and efficiency of its deposition on the substrates applied for plasma separation method

NASA Astrophysics Data System (ADS)

Antonov, N. N.; Samokhin, A. A.; Zhabin, S. N.; Gavrikov, A. V.; Smirnov, V. P.

2016-11-01

Spent nuclear fuel plasma separation method approbation implies the use of model substances. Thus it is necessary to solve the problem of material conversion into a cold plasma flow, as well as the problem of deposition on collectors. For this purpose, we carried out a kinetic and hydrodynamic simulation of the discharge with hot cathode in the lead vapor (lead vapor was injected into the interelectrode gap). Dependencies of the ionization efficiency, electrostatic potential distribution, density distribution of ions and electrons in the discharge gap on the discharge current density and the model substance vapor concentration were obtained. The simulation results show that at discharge current density of about 3.5 A/cm2 and the lead vapor concentration of 2 × 1012 cm-3, the ionization efficiency is close to 60%. Experimental research of the discharge with a hot cathode in the lead vapor was carried out. We also carried out the research of the Pb condensation coefficients on various substrates. For experimental data analysis the numerical model based on Monte Carlo method was used. The research results show that deposition coefficients at medium temperatures of substrates near 70 °C do not drop lower than 75%.

Characterization of a new candidate isotopic reference material for natural Pb using primary measurement method.

PubMed

Nonose, Naoko; Suzuki, Toshihiro; Shin, Ki-Cheol; Miura, Tsutomu; Hioki, Akiharu

2017-06-29

A lead isotopic standard solution with natural abundance has been developed by applying a mixture of a solution of enriched 208 Pb and a solution of enriched 204 Pb ( 208 Pb- 204 Pb double spike solution) as bracketing method. The amount-of-substance ratio of 208 Pb: 204 Pb in this solution is accurately measured by applying EDTA titrimetry, which is one of the primary measurement methods, to each enriched Pb isotope solution. Also metal impurities affecting EDTA titration and minor lead isotopes contained in each enriched Pb isotope solution are quantified by ICP-SF-MS. The amount-of-substance ratio of 208 Pb: 204 Pb in the 208 Pb- 204 Pb double spike solution is 0.961959 ± 0.000056 (combined standard uncertainty; k = 1). Both the measurement of lead isotope ratios in a candidate isotopic standard solution and the correction of mass discrimination in MC-ICP-MS are carried out by coupling of a bracketing method with the 208 Pb- 204 Pb double spike solution and a thallium internal addition method, where thallium solution is added to the standard and the sample. The measured lead isotope ratios and their expanded uncertainties (k = 2) in the candidate isotopic standard solution are 18.0900 ± 0.0046 for 206 Pb: 204 Pb, 15.6278 ± 0.0036 for 207 Pb: 204 Pb, 38.0626 ± 0.0089 for 208 Pb: 204 Pb, 2.104406 ± 0.00013 for 208 Pb: 206 Pb, and 0.863888 ± 0.000036 for 207 Pb: 206 Pb. The expanded uncertainties are about one half of the stated uncertainty for NIST SRM 981, for 208 Pb: 204 Pb, 207 Pb: 204 Pb and 206 Pb: 204 Pb, or one eighth, for 208 Pb: 206 Pb and 207 Pb: 206 Pb, The combined uncertainty consists of the uncertainties due to lead isotope ratio measurements and the remaining time-drift effect of mass discrimination in MC-ICP-MS, which is not removed by the coupled correction method. In the measurement of 208 Pb: 204 Pb, 207 Pb: 204 Pb and 206 Pb: 204 Pb, the latter contribution is two or three times larger than the former. When the coupling of a bracketing method with the 208 Pb- 204 Pb double spike solution and a thallium internal addition method is applied to the analysis of NIST SRM 981, the measured lead isotope ratios are in good agreement with its certified values. This proves that the developed method is not only consistent with the conventional one by NIST SRM 981 but also enables measurement of the lead isotope ratios with higher precision. Copyright © 2017 Elsevier B.V. All rights reserved.

24 CFR 35.1315 - Collection and laboratory analysis of samples.

Code of Federal Regulations, 2013 CFR

2013-04-01

... of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1315...

24 CFR 35.1315 - Collection and laboratory analysis of samples.

Code of Federal Regulations, 2014 CFR

2014-04-01

... of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1315...

24 CFR 35.1315 - Collection and laboratory analysis of samples.

Code of Federal Regulations, 2012 CFR

2012-04-01

... of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1315...

24 CFR 35.1315 - Collection and laboratory analysis of samples.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1315...

24 CFR 35.1315 - Collection and laboratory analysis of samples.

Code of Federal Regulations, 2011 CFR

2011-04-01

... of Housing and Urban Development LEAD-BASED PAINT POISONING PREVENTION IN CERTAIN RESIDENTIAL STRUCTURES Methods and Standards for Lead-Paint Hazard Evaluation and Hazard Reduction Activities § 35.1315...

Post-processing through linear regression

NASA Astrophysics Data System (ADS)

van Schaeybroeck, B.; Vannitsem, S.

2011-03-01

Various post-processing techniques are compared for both deterministic and ensemble forecasts, all based on linear regression between forecast data and observations. In order to evaluate the quality of the regression methods, three criteria are proposed, related to the effective correction of forecast error, the optimal variability of the corrected forecast and multicollinearity. The regression schemes under consideration include the ordinary least-square (OLS) method, a new time-dependent Tikhonov regularization (TDTR) method, the total least-square method, a new geometric-mean regression (GM), a recently introduced error-in-variables (EVMOS) method and, finally, a "best member" OLS method. The advantages and drawbacks of each method are clarified. These techniques are applied in the context of the 63 Lorenz system, whose model version is affected by both initial condition and model errors. For short forecast lead times, the number and choice of predictors plays an important role. Contrarily to the other techniques, GM degrades when the number of predictors increases. At intermediate lead times, linear regression is unable to provide corrections to the forecast and can sometimes degrade the performance (GM and the best member OLS with noise). At long lead times the regression schemes (EVMOS, TDTR) which yield the correct variability and the largest correlation between ensemble error and spread, should be preferred.

Encapsulation of lead from hazardous CRT glass wastes using biopolymer cross-linked concrete systems.

PubMed

Kim, Daeik; Quinlan, Michael; Yen, Teh Fu

2009-01-01

Discarded computer monitors and television sets are identified as hazardous materials due to the high content of lead in their cathode ray tubes (CRTs). Over 98% of lead is found in CRT glass. More than 75% of obsolete electronics including TV and CRT monitors are in storage because appropriate e-waste management and remediation technologies are insufficient. Already an e-waste tsunami is starting to roll across the US and the whole world. Thus, a new technology was developed as an alternative to current disposal methods; this method uses a concrete composite crosslinked with minute amounts of biopolymers and a crosslinking agent. Commercially available microbial biopolymers of xanthan gum and guar gum were used to encapsulate CRT wastes, reducing Pb leachability as measured by standard USEPA methods. In this investigation, the synergistic effect of the crosslinking reaction was observed through blending two different biopolymers or adding a crosslinking agent in biopolymer solution. This CRT-biopolymer-concrete (CBC) composite showed higher compressive strength than the standard concrete and a considerable decrease in lead leachability.

Encapsulation of lead from hazardous CRT glass wastes using biopolymer cross-linked concrete systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Daeik; Quinlan, Michael; Yen, Teh Fu

2009-01-15

Discarded computer monitors and television sets are identified as hazardous materials due to the high content of lead in their cathode ray tubes (CRTs). Over 98% of lead is found in CRT glass. More than 75% of obsolete electronics including TV and CRT monitors are in storage because appropriate e-waste management and remediation technologies are insufficient. Already an e-waste tsunami is starting to roll across the US and the whole world. Thus, a new technology was developed as an alternative to current disposal methods; this method uses a concrete composite crosslinked with minute amounts of biopolymers and a crosslinking agent.more » Commercially available microbial biopolymers of xanthan gum and guar gum were used to encapsulate CRT wastes, reducing Pb leachability as measured by standard USEPA methods. In this investigation, the synergistic effect of the crosslinking reaction was observed through blending two different biopolymers or adding a crosslinking agent in biopolymer solution. This CRT-biopolymer-concrete (CBC) composite showed higher compressive strength than the standard concrete and a considerable decrease in lead leachability.« less

A method of predicting flow rates required to achieve anti-icing performance with a porous leading edge ice protection system

NASA Technical Reports Server (NTRS)

Kohlman, D. L.; Albright, A. E.

1983-01-01

An analytical method was developed for predicting minimum flow rates required to provide anti-ice protection with a porous leading edge fluid ice protection system. The predicted flow rates compare with an average error of less than 10 percent to six experimentally determined flow rates from tests in the NASA Icing Research Tunnel on a general aviation wing section.

Atomic absorption spectrometric determination of copper, zinc, and lead in geological materials

USGS Publications Warehouse

Sanzolone, R.F.; Chao, T.T.

1976-01-01

An atomic absorption spectrometric method is described for the determination of copper, zinc, and lead in geological materials. The sample is digested with HF-HCl-H2O2; the final solution for analysis is in 10 % (v/v) HCl. Copper and zinc are determined directly by aspirating the solution into an air-acetylene flame. A separate aliquot of the solution is used for determination of lead; lead is extracted into TOPO-MIBK from the acidic solution in the presence of iodide and ascorbic acid. For a 0.50-g sample, the limits of determination are 10-2000 p.p.m. for Cu and Zn, and 5-5000 p.p.m. for Pb. As much as 40 % Fe or Ca. and 10 % Al, Mg, or Mn in the sample do not interfere. The proposed method can be applied to the determination of copper, zinc, and lead in a wide range of geological materials including iron- and manganese-rich, calcareous and carbonate samples. ?? 1976.

Dynamic filtration and static adsorption of lead ions in aqueous solution by use of blended polysulfone membranes with nano size MCM-41 particles coated by polyaniline.

PubMed

Toosi, Mohammad Reza; Emami, Mohammad Reza Sarmasti; Hajian, Sudeh

2018-05-11

MCM-41 mesopore was prepared by hydrothermal method and used for synthesis of polyaniline/MCM-41 nanocomposite via in situ polymerization. The nanocomposite was blended with polysulfone to prepare mixed matrix membrane in different content of nanocomposite by phase inversion method. Structural and surface properties of the samples were characterized by SEM, XRD, FTIR, AFM, TGA, BET, and zeta potential measurements. Effect of the nanocomposite content on the hydrophilicity, porosity, and permeability of the membrane was determined. Membrane performance was evaluated for removal of lead ions in dynamic filtration and static adsorption. The membranes were found as effective adsorptive filters for removal of lead ions via interactions between active sites of nanocomposite in membrane structure and lead ions during filtration. Results of batch experiments proved adsorptive mechanism of membranes for removal of lead ions with the maximum adsorption capacity of 19.6 mg/g.

Assessment of the clinical efficacy of the heart spectrum blood pressure monitor for diagnosis of atrial fibrillation: An unblinded clinical trial.

PubMed

Kao, Wei-Fong; Hou, Sen-Kuang; Huang, Chun-Yao; Chao, Chun-Chieh; Cheng, Chung-Chih; Chen, Yi-Jung

2018-01-01

Atrial fibrillation (AF) is the most common arrhythmia. The most common diagnostic method, 12-lead electrocardiogram (ECG), can record episodes of arrhythmia from which the type and severity can be determined. The Heart Spectrum Blood Pressure Monitor (P2; OSTAR Meditech Corp., New Taipei City, Taiwan) is used to measure cardiovascular pressure change with fast Fourier transform (FFT) analysis to obtain heart rate frequency variability and accurate blood pressure data. We compared the diagnostic efficacy of the Heart Spectrum Blood Pressure Monitor to a 12-lead ECG (gold standard) for patients with AF. Three measurement methods were used in this study to analyze the heart index and compare the results with simultaneous 12-lead ECG: blood pressure; mean arterial pressure, which was calculated from individual blood pressure as a constant pressure; and a constant pressure of 60 mmHg. The physician used a 12-lead ECG and the Heart Spectrum Blood Pressure Monitor simultaneously. The Heart Spectrum Blood Pressure Monitor used FFT analysis to diagnose AF, and the findings were compared to the 12-lead ECG readings. This unblinded clinical trial was conducted in the emergency department of Taipei Medical University Hospital. Twenty-nine subjects with AF and 33 without AF aged 25 to 97 y (mean, 63.5 y) were included. Subjects who were exposed to high-frequency surgical equipment during testing, those with cardiac pacemakers or implantable defibrillators, and pregnant women were excluded. The sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) were 97%, 97%, 97%, and 97%, respectively, for method 1; 90%, 100%, 100%, and 91%, respectively, for method 2; and 100%, 94%, 94%, and 100%, respectively, for method 3. The sensitivity, specificity, PPV, and NPV for both methods ranged between 90% and 100%, indicating that the Heart Spectrum Blood Pressure Monitor can be effectively applied for AF detection.

Assessment of the clinical efficacy of the heart spectrum blood pressure monitor for diagnosis of atrial fibrillation: An unblinded clinical trial

PubMed Central

Kao, Wei-Fong; Hou, Sen-Kuang; Huang, Chun-Yao; Cheng, Chung-Chih; Chen, Yi-Jung

2018-01-01

Atrial fibrillation (AF) is the most common arrhythmia. The most common diagnostic method, 12-lead electrocardiogram (ECG), can record episodes of arrhythmia from which the type and severity can be determined. The Heart Spectrum Blood Pressure Monitor (P2; OSTAR Meditech Corp., New Taipei City, Taiwan) is used to measure cardiovascular pressure change with fast Fourier transform (FFT) analysis to obtain heart rate frequency variability and accurate blood pressure data. We compared the diagnostic efficacy of the Heart Spectrum Blood Pressure Monitor to a 12-lead ECG (gold standard) for patients with AF. Three measurement methods were used in this study to analyze the heart index and compare the results with simultaneous 12-lead ECG: blood pressure; mean arterial pressure, which was calculated from individual blood pressure as a constant pressure; and a constant pressure of 60 mmHg. The physician used a 12-lead ECG and the Heart Spectrum Blood Pressure Monitor simultaneously. The Heart Spectrum Blood Pressure Monitor used FFT analysis to diagnose AF, and the findings were compared to the 12-lead ECG readings. This unblinded clinical trial was conducted in the emergency department of Taipei Medical University Hospital. Twenty-nine subjects with AF and 33 without AF aged 25 to 97 y (mean, 63.5 y) were included. Subjects who were exposed to high-frequency surgical equipment during testing, those with cardiac pacemakers or implantable defibrillators, and pregnant women were excluded. The sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) were 97%, 97%, 97%, and 97%, respectively, for method 1; 90%, 100%, 100%, and 91%, respectively, for method 2; and 100%, 94%, 94%, and 100%, respectively, for method 3. The sensitivity, specificity, PPV, and NPV for both methods ranged between 90% and 100%, indicating that the Heart Spectrum Blood Pressure Monitor can be effectively applied for AF detection. PMID:29902218

Health Risk Assessment of Lead Ingestion Exposure by Particle Sizes in Crumb Rubber on Artificial Turf Considering Bioavailability

PubMed Central

Kim, Sunduk; Yang, Ji-Yeon; Kim, Ho-Hyun; Yeo, In-Young; Shin, Dong-Chun

2012-01-01

Objectives The purpose of this study was to assess the risk of ingestion exposure of lead by particle sizes of crumb rubber in artificial turf filling material with consideration of bioavailability. Methods This study estimated the ingestion exposure by particle sizes (more than 250 um or less than 250 um) focusing on recyclable ethylene propylene diene monomer crumb rubber being used as artificial turf filling. Analysis on crumb rubber was conducted using body ingestion exposure estimate method in which total content test method, acid extraction method and digestion extraction method are reflected. Bioavailability which is a calibrating factor was reflected in ingestion exposure estimate method and applied in exposure assessment and risk assessment. Two methods using acid extraction and digestion extraction concentration were compared and evaluated. Results As a result of the ingestion exposure of crumb rubber material, the average lead exposure amount to the digestion extraction result among crumb rubber was calculated to be 1.56×10-4 mg/kg-day for low grade elementary school students and 4.87×10-5 mg/kg-day for middle and high school students in 250 um or less particle size, and that to the acid extraction result was higher than the digestion extraction result. Results of digestion extraction and acid extraction showed that the hazard quotient was estimated by about over 2 times more in particle size of lower than 250 um than in higher than 250 um. There was a case of an elementary school student in which the hazard quotient exceeded 0.1. Conclusions Results of this study confirm that the exposure of lead ingestion and risk level increases as the particle size of crumb rubber gets smaller. PMID:22355803

Cloud field classification based upon high spatial resolution textural features. II - Simplified vector approaches

NASA Technical Reports Server (NTRS)

Chen, D. W.; Sengupta, S. K.; Welch, R. M.

1989-01-01

This paper compares the results of cloud-field classification derived from two simplified vector approaches, the Sum and Difference Histogram (SADH) and the Gray Level Difference Vector (GLDV), with the results produced by the Gray Level Cooccurrence Matrix (GLCM) approach described by Welch et al. (1988). It is shown that the SADH method produces accuracies equivalent to those obtained using the GLCM method, while the GLDV method fails to resolve error clusters. Compared to the GLCM method, the SADH method leads to a 31 percent saving in run time and a 50 percent saving in storage requirements, while the GLVD approach leads to a 40 percent saving in run time and an 87 percent saving in storage requirements.

Linking Geological and Health Sciences to Assess Childhood Lead Poisoning from Artisanal Gold Mining in Nigeria

PubMed Central

Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather A.; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behbod, Behrooz; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally. PMID:23524139

Linking geology and health sciences to assess childhood lead poisoning from artisanal gold mining in Nigeria

USGS Publications Warehouse

Plumlee, Geoffrey S.; Durant, James T.; Morman, Suzette A.; Neri, Antonio; Wolf, Ruth E.; Dooyema, Carrie A.; Hageman, Philip L.; Lowers, Heather; Fernette, Gregory L.; Meeker, Gregory P.; Benzel, William M.; Driscoll, Rhonda L.; Berry, Cyrus J.; Crock, James G.; Goldstein, Harland L.; Adams, Monique; Bartrem, Casey L.; Tirima, Simba; Behrooz, Behbod; von Lindern, Ian; Brown, Mary Jean

2013-01-01

Background: In 2010, Médecins Sans Frontières discovered a lead poisoning outbreak linked to artisanal gold processing in northwestern Nigeria. The outbreak has killed approximately 400 young children and affected thousands more. Objectives: Our aim was to undertake an interdisciplinary geological- and health-science assessment to clarify lead sources and exposure pathways, identify additional toxicants of concern and populations at risk, and examine potential for similar lead poisoning globally. Methods: We applied diverse analytical methods to ore samples, soil and sweep samples from villages and family compounds, and plant foodstuff samples. Results: Natural weathering of lead-rich gold ores before mining formed abundant, highly gastric-bioaccessible lead carbonates. The same fingerprint of lead minerals found in all sample types confirms that ore processing caused extreme contamination, with up to 185,000 ppm lead in soils/sweep samples and up to 145 ppm lead in plant foodstuffs. Incidental ingestion of soils via hand-to-mouth transmission and of dusts cleared from the respiratory tract is the dominant exposure pathway. Consumption of water and foodstuffs contaminated by the processing is likely lesser, but these are still significant exposure pathways. Although young children suffered the most immediate and severe consequences, results indicate that older children, adult workers, pregnant women, and breastfed infants are also at risk for lead poisoning. Mercury, arsenic, manganese, antimony, and crystalline silica exposures pose additional health threats. Conclusions: Results inform ongoing efforts in Nigeria to assess lead contamination and poisoning, treat victims, mitigate exposures, and remediate contamination. Ore deposit geology, pre-mining weathering, and burgeoning artisanal mining may combine to cause similar lead poisoning disasters elsewhere globally.

Effect of the Crystal Structure on the Electrical Properties of Thin-Film PZT Structures

NASA Astrophysics Data System (ADS)

Delimova, L. A.; Gushchina, E. V.; Zaitseva, N. V.; Seregin, D. S.; Vorotilov, K. A.; Sigov, A. S.

2018-03-01

A new method of two-stage crystallization of lead zirconate-titanate (PZT) films using a seed sublayer with a low excess lead content has been proposed and realized. A seed layer with a strong texture of perovskite Pe(111) grains is formed from a solution with a lead excess of 0-5 wt %; the fast growth of the grains is provided by the deposition of the main film from a solution with high lead content. As a result, a strong Pe(111) texture with complete suppression of the Pe(100) orientation forms. An analysis of current-voltage dependences of the transient currents and the distributions of the local conductivity measured by the contact AFM method reveals two various mechanisms of current percolation that are determined by traps in the bulk and at the perovskite grain interfaces.

Hit discovery and hit-to-lead approaches.

PubMed

Keseru, György M; Makara, Gergely M

2006-08-01

Hit discovery technologies range from traditional high-throughput screening to affinity selection of large libraries, fragment-based techniques and computer-aided de novo design, many of which have been extensively reviewed. Development of quality leads using hit confirmation and hit-to-lead approaches present their own challenges, depending on the hit discovery method used to identify the initial hits. In this paper, we summarize common industry practices adopted to tackle hit-to-lead challenges and review how the advantages and drawbacks of different hit discovery techniques could affect the various issues hit-to-lead groups face.

Study of supersonic wings employing the attainable leading-edge thrust concept

NASA Technical Reports Server (NTRS)

Middleton, W. D.

1982-01-01

A theoretical study was made of supersonic wing geometries at Mach 1.8, using the attainable leading-edge thrust concept. The attainable thrust method offers a powerful means to improve overall aerodynamic efficiency by identifying wing leading-edge geometries that promote attached flow and by defining a local angle-of-attack range over which attached flow may be obtained. The concept applies to flat and to cambered wings, which leads to the consideration of drooped-wing leading edges for attached flow at high lift coefficients.

Moveable Leading Edge Device for a Wing

NASA Technical Reports Server (NTRS)

Pitt, Dale M. (Inventor); Eckstein, Nicholas Stephen (Inventor)

2013-01-01

A method and apparatus for managing a flight control surface system. A leading edge section on a wing of an aircraft is extended into a deployed position. A deformable section connects the leading edge section to a trailing section. The deformable section changes from a deformed shape to an original shape when the leading edge section is moved into the deployed position. The leading edge section on the wing is moved from the deployed position to an undeployed position. The deformable section changes to the deformed shape inside of the wing.

Vapor cooled current lead for cryogenic electrical equipment

DOEpatents

Vansant, James H.

1983-01-01

Apparatus and method are provided for conducting electric current to cryogenic electrical equipment devices. A combination of inner and outer tubes together form a plurality of hollow composite tubes housed in a sheath. Top and bottom block mounting means are fitted to hold the composite tubes and are affixed to the ends of the sheath. This combination forms a current lead. The current lead is attached to a cryogenic device housing a fluid coolant which moves through the current lead, cooling the current lead as the fluid travels.

7 CFR Exhibit H to Subpart A of... - Prohibition of Lead-Based Paints

Code of Federal Regulations, 2011 CFR

2011-01-01

... prohibiting the use of lead-based paint in all contracts and subcontracts for construction or rehabilitation... 7 Agriculture 12 2011-01-01 2011-01-01 false Prohibition of Lead-Based Paints H Exhibit H to...-Based Paints I. Purpose This exhibit prescribes the methods to be used to comply with the requirements...

[Determination of Trace Lead in Water by UV-Visible Diffuse Reflectance Spectroscopy Combined with Surfactant and Membrane Filtration-Enrichment].

PubMed

Zhang, Xiao-fang; Zhu, Bi-lin; Li, Wei; Wang, Lei; Zhang, Lei; Wu, Ting; Du, Yi-ping

2015-07-01

In this paper, a method of determination of trace lead in water by UV-Visible diffuse reflectance spectroscopy combined with surfactant and membrane filtration enrichment was proposed. In the NH3 x H2O-NH4Cl buffer solution with pH 8.5, the lead(II) ion would react with dithizone to form the red complex under vigorous stirring, which is hydrophobic and can be enriched by the mixed cellulose ester membrane. In addition, the nonionic surfactant Polyoxyethylene lauryl ether (Brij-30) was added into the solution to improve the enrichment efficiency, then visible diffuse reflectance spectra of the membrane were measured directly after the membrane were naturally dried. We also optimized the reaction conditions which may affect the complexation reaction process, such as type of surfactants, the concentration of the surfactant, the reaction acidity, the concentration of dithizone as well as the reaction time. The research results show that under the optimum conditions, a good linear correlation between absorbance at 485 nm and concentration of lead in the range of 5.0-100.0 microg x L(-1) was obtained with a squared correlation coefficient (R2) of 0.9906, and the detection limit was estimated accordingly to be 2.88 microg x L(-1). To determine real water sample, the interference from some potential coexisting ions was also studied at the optimal conditions when the concentration of lead (II) ion standard solution was fixed to 20 microg x L(-1). The results indicate that the following ions cannot interfere in the determination of lead with the proposed method: 500 times of the K+, Na+, Ca2+, Mg2+, NH4+, NO3-, Cl-, CH3COO-, SO4(2-); 10 times of the Al3+ (using 10% NaF as a masking reagent to avoid the interference); 10 times of the Fe3+ (using 10% NaF and 10% sodium potassium tartrate as masking reagents); 10 times of Hg2+ or Zn2+ (using 10% NaSCN and 10% potassium sodium tartrate as masking reagents); the same amount of Cd2+, Cu2+. The proposed method was applied to the determnation of lead (II) in bottled water as a real sample. The determination results show good agreements between the proposed method and graphite furnace atomic absorption spectrometry (GFAAS) method. The recoveries in case of spiked real samples were between 95.4% and 104.5%, and the standard deviations (SD) were between 0.5 micro x L(-1) and 1.5 microg x L(-1), which indicate that the method developed in the present work with advantages of accuracy, simpleness, sensitiveness are of potential application for the determination of trace lead in water samples.

Lead Poison Detection

NASA Technical Reports Server (NTRS)

1976-01-01

With NASA contracts, Whittaker Corporations Space Science division has developed an electro-optical instrument to mass screen for lead poisoning. Device is portable and detects protoporphyrin in whole blood. Free corpuscular porphyrins occur as an early effect of lead ingestion. Also detects lead in urine used to confirm blood tests. Test is inexpensive and can be applied by relatively unskilled personnel. Similar Whittaker fluorometry device called "drug screen" can measure morphine and quinine in urine much faster and cheaper than other methods.

A fast and sensitive TLD method for measurement of energy and homogeneity of electron beams using transmitted radiation through lead.

PubMed

Pradhan, A S; Quast, U; Sharma, P K

1994-09-01

A simple and fast, but sensitive TLD method for the measurement of energy and homogeneity of therapeutically used electron beams has been developed and tested. This method is based on the fact that when small thicknesses of high-Z absorbers such as lead are interposed in the high-energy electron beams, the transmitted radiation increases with the energy of the electron beams. Consequently, the ratio of readouts of TLDS held on the two sides of a lead plate varied sharply (by factor of 70) with a change in energy of the electron beam from 5 MeV to 18 MeV, offering a very sensitive method for the measurement of the energy of electron beams. By using the ratio of TL readouts of two types of TLD ribbon with widely different sensitivities, LiF TLD-700 ribbons on the upstream side and highly sensitive CaF2:Dy TLD-200 ribbons on the downstream side, an electron energy discrimination of better than +/- 0.1 MeV could be achieved. The homogeneity of the electron beam energy and the absorbed dose was measured by using a jig in which the TLDS were held in the desired array on both sides of a 4 mm thick lead plate. The method takes minimal beam time and makes it possible to carry out measurements for the audit of the quality of electron beams as well as for intercomparison of beams by mail.

Development of a GC/MS method for the qualitative and quantitative analysis of mixtures of free fatty acids and metal soaps in paint samples.

PubMed

La Nasa, Jacopo; Modugno, Francesca; Aloisi, Matteo; Lluveras-Tenorio, Anna; Bonaduce, Ilaria

2018-02-25

In this paper we present a new analytical GC/MS method for the analysis of mixtures of free fatty acids and metal soaps in paint samples. This approach is based on the use of two different silylating agents: N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) and 1,1,1,3,3,3-hexamethyldisilazane (HMDS). Our experimentation demonstrated that HMDS does not silylate fatty acid carboxylates, so it can be used for the selective derivatization and GC/MS quantitative analysis of free fatty acids. On the other hand BSTFA is able to silylate both free fatty acids and fatty acids carboxylates. The reaction conditions for the derivatization of carboxylates with BSTFA were thus optimized with a full factorial 3 2 experimental design using lead stearate and lead palmitate as model systems. The analytical method was validated following the ICH guidelines. The method allows the qualitative and quantitative analysis of fatty acid carboxylates of sodium, calcium, magnesium, aluminium, manganese, cobalt, copper, zinc, cadmium, and lead and of lead azelate. In order to exploit the performances of the new analytical method, samples collected from two reference paint layers, from a gilded 16th century marble sculpture, and from a paint tube belonging to the atelier of Edvard Munch, used in the last period of his life (1916-1944), were characterized. Copyright © 2017 Elsevier B.V. All rights reserved.

TOT measurement implemented in FPGA TDC

NASA Astrophysics Data System (ADS)

Fan, Huan-Huan; Cao, Ping; Liu, Shu-Bin; An, Qi

2015-11-01

Time measurement plays a crucial role for the purpose of particle identification in high energy physics experiments. With increasingly demanding physics goals and the development of electronics, modern time measurement systems need to meet the requirement of excellent resolution specification as well as high integrity. Based on Field Programmable Gate Arrays (FPGAs), FPGA time-to-digital converters (TDCs) have become one of the most mature and prominent time measurement methods in recent years. For correcting the time-walk effect caused by leading timing, a time-over-threshold (TOT) measurement should be added to the FPGA TDC. TOT can be obtained by measuring the interval between the signal leading and trailing edges. Unfortunately, a traditional TDC can recognize only one kind of signal edge, the leading or the trailing. Generally, to measure the interval, two TDC channels need to be used at the same time, one for leading, the other for trailing. However, this method unavoidably increases the amount of FPGA resources used and reduces the TDC's integrity. This paper presents one method of TOT measurement implemented in a Xilinx Virtex-5 FPGA. In this method, TOT measurement can be achieved using only one TDC input channel. The consumed resources and time resolution can both be guaranteed. Testing shows that this TDC can achieve resolution better than 15ps for leading edge measurement and 37 ps for TOT measurement. Furthermore, the TDC measurement dead time is about two clock cycles, which makes it good for applications with higher physics event rates. Supported by National Natural Science Foundation of China (11079003, 10979003)

Thermo-Acoustic Ultrasound for Detection of RF-Induced Device Lead Heating in MRI.

PubMed

Dixit, Neerav; Stang, Pascal P; Pauly, John M; Scott, Greig C

2018-02-01

Patients who have implanted medical devices with long conductive leads are often restricted from receiving MRI scans due to the danger of RF-induced heating near the lead tips. Phantom studies have shown that this heating varies significantly on a case-by-case basis, indicating that many patients with implanted devices can receive clinically useful MRI scans without harm. However, the difficulty of predicting RF-induced lead tip heating prior to scanning prevents numerous implant recipients from being scanned. Here, we demonstrate that thermo-acoustic ultrasound (TAUS) has the potential to be utilized for a pre-scan procedure assessing the risk of RF-induced lead tip heating in MRI. A system was developed to detect TAUS signals by four different TAUS acquisition methods. We then integrated this system with an MRI scanner and detected a peak in RF power absorption near the tip of a model lead when transmitting from the scanner's body coil. We also developed and experimentally validated simulations to characterize the thermo-acoustic signal generated near lead tips. These results indicate that TAUS is a promising method for assessing RF implant safety, and with further development, a TAUS pre-scan could allow many more patients to have access to MRI scans of significant clinical value.

Vortex assisted solid-phase extraction of lead(II) using orthorhombic nanosized Bi2WO6 as a sorbent.

PubMed

Baghban, Neda; Yilmaz, Erkan; Soylak, Mustafa

2017-12-07

Nanosized single crystal orthorhombic Bi 2 WO 6 was synthesized by a hydrothermal method and used as a sorbent for vortex assisted solid phase extraction of lead(II). The crystal and molecular structure of the sorbent was examined using XRD, Raman, SEM and SEM-EDX analysis. Various parameters affecting extraction efficiency were optimized by using multivariate design. The effect of diverse ions on the extraction also was studied. Lead was quantified by flame atomic absorption spectrometry (FAAS). The recoveries of lead(II) from spiked samples (at a typical spiking level of 200-400 ng·mL -1 ) are >95%. Other figures of merit includes (a) a detection limit of 6 ng·mL -1 , (b) a preconcentration factor of 50, (c) a relative standard deviation of 1.6%, and (d) and adsorption capacity of 6.6 mg·g -1 . The procedure was successfully applied to accurate determination of lead in (spiked) pomegranate and water samples. Graphical abstract Nanosized single crystal orthorhombic Bi 2 WO 6 was synthesized and characterized by a hydrothermal method and used as a sorbent for vortex assisted solid phase extraction of lead(II). The procedure was successfully applied to accurate determination of lead in (spiked) pomegranate and water samples.

Evaluation of Small Arms Range Soils for Metal Contamination and Lead Bioavailability

DTIC Science & Technology

2009-11-03

measured by an in vivo or in vitro method. Risk assessment and/or remediation of small arms ranges should therefore assume a high relative bioavailability of...lead for the eight soils was about 100% (108 ( 18% and 95 ( 6%, respectively) showing good agreement between both methods. Risk assessment and/ or...significant efforts in stewardship, environmental risk assessment , and reme- diation, so that training of personnel and future land use can be

Effect of positive pulse charge waveforms on the energy efficiency of lead-acid traction cells

NASA Technical Reports Server (NTRS)

Smithrick, J. J.

1981-01-01

The effects of four different charge methods on the energy conversion efficiency of 300 ampere hour lead acid traction cells were investigated. Three of the methods were positive pulse charge waveforms; the fourth, a constant current method, was used as a baseline of comparison. The positive pulse charge waveforms were: 120 Hz full wave rectified sinusoidal; 120 Hz silicon controlled rectified; and 1 kHz square wave. The constant current charger was set at the time average pulse current of each pulse waveform, which was 150 amps. The energy efficiency does not include charger losses. The lead acid traction cells were charged to 70 percent of rated ampere hour capacity in each case. The results of charging the cells using the three different pulse charge waveforms indicate there was no significant difference in energy conversion efficiency when compared to constant current charging at the time average pulse current value.

Calculation of smooth potential energy surfaces using local electron correlation methods

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mata, Ricardo A.; Werner, Hans-Joachim

2006-11-14

The geometry dependence of excitation domains in local correlation methods can lead to noncontinuous potential energy surfaces. We propose a simple domain merging procedure which eliminates this problem in many situations. The method is applied to heterolytic bond dissociations of ketene and propadienone, to SN2 reactions of Cl{sup -} with alkylchlorides, and in a quantum mechanical/molecular mechanical study of the chorismate mutase enzyme. It is demonstrated that smooth potentials are obtained in all cases. Furthermore, basis set superposition error effects are reduced in local calculations, and it is found that this leads to better basis set convergence when computing barriermore » heights or weak interactions. When the electronic structure strongly changes between reactants or products and the transition state, the domain merging procedure leads to a balanced description of all structures and accurate barrier heights.« less

Performance of Lead-Free versus Lead-Based Hunting Ammunition in Ballistic Soap

PubMed Central

Gremse, Felix; Krone, Oliver; Thamm, Mirko; Kiessling, Fabian; Tolba, René Hany; Rieger, Siegfried; Gremse, Carl

2014-01-01

Background Lead-free hunting bullets are an alternative to lead-containing bullets which cause health risks for humans and endangered scavenging raptors through lead ingestion. However, doubts concerning the effectiveness of lead-free hunting bullets hinder the wide-spread acceptance in the hunting and wildlife management community. Methods We performed terminal ballistic experiments under standardized conditions with ballistic soap as surrogate for game animal tissue to characterize dimensionally stable, partially fragmenting, and deforming lead-free bullets and one commonly used lead-containing bullet. The permanent cavities created in soap blocks are used as a measure for the potential wound damage. The soap blocks were imaged using computed tomography to assess the volume and shape of the cavity and the number of fragments. Shots were performed at different impact speeds, covering a realistic shooting range. Using 3D image segmentation, cavity volume, metal fragment count, deflection angle, and depth of maximum damage were determined. Shots were repeated to investigate the reproducibility of ballistic soap experiments. Results All bullets showed an increasing cavity volume with increasing deposited energy. The dimensionally stable and fragmenting lead-free bullets achieved a constant conversion ratio while the deforming copper and lead-containing bullets showed a ratio, which increases linearly with the total deposited energy. The lead-containing bullet created hundreds of fragments and significantly more fragments than the lead-free bullets. The deflection angle was significantly higher for the dimensionally stable bullet due to its tumbling behavior and was similarly low for the other bullets. The deforming bullets achieved higher reproducibility than the fragmenting and dimensionally stable bullets. Conclusion The deforming lead-free bullet closely resembled the deforming lead-containing bullet in terms of energy conversion, deflection angle, cavity shape, and reproducibility, showing that similar terminal ballistic behavior can be achieved. Furthermore, the volumetric image processing allowed superior analysis compared to methods that involve cutting of the soap blocks. PMID:25029572

Determining the effect of cartridge case coatings on GSR using post-fire priming cup residue.

PubMed

Terry, Molly; Fookes, Barry; Bridge, Candice M

2017-07-01

Ammunition is typically composed of a lead-based priming mixture which contributes to the characteristics most commonly used for the identification of gunshot residue (GSR). Due to the health risks often associated with lead, the use of lead-free primers in ammunitions is becoming more popular. Thus, the presence of GSR is becoming more difficult to discern based on the traditional means, i.e. the presence of lead (Pb), barium (Ba), and antimony (Sb). While research has been conducted on the differences between lead-based and lead-free muzzle discharge residue, few have researched other components of ammunition which may lead to other means of characterizing GSR. This research, therefore, covers that gap by focusing on the priming cup present in ammunition and the residue which may originate from it, that can contribute to muzzle discharge residue. In this study, a lead-based and a lead-free ammunition from four different manufacturers were chosen. The cartridges were fired using a Glock 17, 9mm Parabellum, collected post-fire, and subsequently de-primed resulting in the removal of the anvil. The GSR present on the anvils and cups was analyzed using scanning electron microscopy coupled with energy dispersive x-ray spectrometry (SEM-EDX). The data was then processed using unit vector analysis for normalization and analyzed using principal component analysis (PCA) and linear discriminant analysis (LDA). This data was then used to determine the components of the cartridge case which contribute to GSR and develop a method of characterization between lead-free and lead-based ammunition. Such a method will improve the detection of GSR by strengthening the criteria of identification. Copyright © 2017 Elsevier B.V. All rights reserved.

Aeroelastic loads prediction for an arrow wing. Task 3: Evaluation of the Boeing three-dimensional leading-edge vortex code

NASA Technical Reports Server (NTRS)

Manro, M. E.

1983-01-01

Two separated flow computer programs and a semiempirical method for incorporating the experimentally measured separated flow effects into a linear aeroelastic analysis were evaluated. The three dimensional leading edge vortex (LEV) code is evaluated. This code is an improved panel method for three dimensional inviscid flow over a wing with leading edge vortex separation. The governing equations are the linear flow differential equation with nonlinear boundary conditions. The solution is iterative; the position as well as the strength of the vortex is determined. Cases for both full and partial span vortices were executed. The predicted pressures are good and adequately reflect changes in configuration.

Recycling of waste lead storage battery by vacuum methods.

PubMed

Lin, Deqiang; Qiu, Keqiang

2011-07-01

Waste lead storage battery is the most important recyclable lead material not only in various European and other OECD countries but also in China. Pollution control of lead has become the focus of people's attention in the world. A vacuum process for recycling waste lead storage battery was developed in this work. The experimental results showed that all the valuable materials in waste lead storage battery could be satisfactorily recycled by vacuum technologies. The vacuum melting of lead grids and the vacuum reduction of lead pastes produce the lead bullion with the direct recovery ratio of 96.29% and 98.98%, respectively. The vacuum pyrolysis of plastics can produce pyrolysis oil with yield of more than 93 wt.%. These vacuum recycling technologies offer improvements in metallurgical and environmental performance. Copyright © 2011 Elsevier Ltd. All rights reserved.

On the study of wavy leading-edge vanes to achieve low fan interaction noise

NASA Astrophysics Data System (ADS)

Tong, Fan; Qiao, Weiyang; Xu, Kunbo; Wang, Liangfeng; Chen, Weijie; Wang, Xunnian

2018-04-01

The application of wavy leading-edge vanes to reduce a single-stage axial fan noise is numerically studied. The aerodynamic and acoustic performance of the fan is numerically investigated using a hybrid unsteady Reynolds averaged Navier-Stokes (URANS)/acoustic analogy method (Goldstein equations). First, the hybrid URANS/Goldstein method is developed and successfully validated against experiment results. Next, numerical simulations are performed to investigate the noise reduction effects of the wavy leading-edge vanes. The aerodynamic and acoustic performance is assessed for a fan with vanes equipped with two different wavy leading-edge profiles and compared with the performance of conventional straight leading-edge vanes. Results indicate that a fan with wavy leading-edge vanes produces lower interaction noise than the baseline fan without a significant loss in aerodynamic performance. In fact, it is demonstrated that wavy leading-edge vanes have the potential to lead to both aerodynamic and acoustic improvements. The two different wavy leading-edge profiles are shown to successfully reduce the fan tone sound power level by 1.2 dB and 4.3 dB, respectively. Fan efficiency is also improved by about 1% with one of the tested wavy leading-edge profiles. Large eddy simulation (LES) is also performed for a simplified fan stage model to assess the effects of wavy leading-edge vanes on the broadband fan noise. Results indicate that the overall sound power level of a fan can be reduced by about 4 dB with the larger wavy leading-edge profile. Finally, the noise reduction mechanisms are investigated and analysed. It is found that the wavy leading-edge profiles can induce significant streamwise vorticity around the leading-edge protuberances and reduce pressure fluctuations (especially at locations of wavy leading-edge hills) and unsteady forces on the stator vanes. The underlying mechanism of the reduced pressure fluctuations is also discussed by examining the magnitude-squared coherence between the velocity and pressure fluctuations in the vicinity of the noise sources. Moreover, a reduction in the correlation level of the wall pressure fluctuations along the vane leading-edge is observed, as well as destructive phase interference along the vane leading-edge.

Cumulant generating function formula of heat transfer in ballistic systems with lead-lead coupling and general nonlinear systems

NASA Astrophysics Data System (ADS)

Li, Huanan

2013-03-01

Based on a two-time observation protocol, we consider heat transfer in a given time interval tM in a lead-junction-lead system taking coupling between the leads into account. In view of the two-time observation, consistency conditions are carefully verified in our specific family of quantum histories. Furthermore, its implication is briefly explored. Then using the nonequilibrium Green's function method, we obtain an exact formula for the cumulant generating function for heat transfer between the two leads, valid in both transient and steady-state regimes. Also, a compact formula for the cumulant generating function in the long-time limit is derived, for which the Gallavotti-Cohen fluctuation symmetry is explicitly verified. In addition, we briefly discuss Di Ventra's repartitioning trick regarding whether the repartitioning procedure of the total Hamiltonian affects the nonequilibrium steady-state current fluctuation. All kinds of properties of nonequilibrium current fluctuations, such as the fluctuation theorem in different time regimes, could be readily given according to these exact formulas. Finally a practical formalism dealing with cumulants of heat transfer across general nonlinear quantum systems is established based on field theoretical/algebraic method.

Lead User Design: Medication Management in Electronic Medical Records.

PubMed

Price, Morgan; Weber, Jens H; Davies, Iryna; Bellwood, Paule

2015-01-01

Improvements in medication management may lead to a reduction of preventable errors. Usability and user experience issues are common and related to achieving benefits of Electronic Medical Records (EMRs). This paper reports on a novel study that combines the lead user method with a safety engineering review to discover an innovative design for the medication management module in EMRs in primary care. Eight lead users were recruited that represented prescribers and clinical pharmacists with expertise in EMR design, evidence-based medicine, medication safety and medication research. Eight separate medication management module designs were prototyped and validated, one with each lead user. A parallel safety review of medicaiton management was completed. The findings were synthesized into a single common set of goals, activities and one interactive, visual prototype. The lead user method with safety review proved to be an effective way to elicit diverse user goals and synthesize them into a common design. The resulting design ideas focus on meeting the goals of quality, efficiency, safety, reducing the cognitive load on the user, and improving communication wih the patient and the care team. Design ideas are being adapted to an existing EMR product, providing areas for further work.

Eco-Balance analysis of the disused lead-acid-batteries recycling technology

NASA Astrophysics Data System (ADS)

Kamińska, Ewa; Kamiński, Tomasz

2017-10-01

The article presents the results of the eco-balance analysis of the disused lead-acid batteries recycling process. Test-dedicated technology offers the possibility to recover other elements, for example, polypropylene of the battery case or to obtain crystalline sodium sulphate. The life cycle assessment was made using ReCiPe and IMPACT2002 + methods. The results are shown as environmental points [Pt]. The results are shown in the environmental categories, specific for each of the methods grouped in the impact categories. 1 Mg of the processed srap was a dopted as the functional unit. The results of the analyses indicate that recycling processes may provide the environmental impact of recycling technology less harmful. Repeated use of lead causes that its original sources are not explored. Similarly, the use of granule production-dedicated polypropylene extracted from battery casings that are used in the plastics industry, has environmental benefits. Due to the widespread use of lead-acid batteries, the attention should be paid to their proper utilization, especially in terms of heavy metals, especially lead. According to the calculations, the highest level of environmental benefits from the use of lead from secondary sources in the production of new products, was observed in the refining process.

Attaching Copper Wires to Magnetic-Reed-Switch Leads

NASA Technical Reports Server (NTRS)

Kamila, Rudolf

1987-01-01

Bonding method reliably joins copper wires to short iron-alloy leads from glass-encased dry magnetic-reed switch without disturbing integrity of glass-to-metal seal. Joint resistant to high temperatures and has low electrical resistance.

Identifying critical transitions and their leading biomolecular networks in complex diseases.

PubMed

Liu, Rui; Li, Meiyi; Liu, Zhi-Ping; Wu, Jiarui; Chen, Luonan; Aihara, Kazuyuki

2012-01-01

Identifying a critical transition and its leading biomolecular network during the initiation and progression of a complex disease is a challenging task, but holds the key to early diagnosis and further elucidation of the essential mechanisms of disease deterioration at the network level. In this study, we developed a novel computational method for identifying early-warning signals of the critical transition and its leading network during a disease progression, based on high-throughput data using a small number of samples. The leading network makes the first move from the normal state toward the disease state during a transition, and thus is causally related with disease-driving genes or networks. Specifically, we first define a state-transition-based local network entropy (SNE), and prove that SNE can serve as a general early-warning indicator of any imminent transitions, regardless of specific differences among systems. The effectiveness of this method was validated by functional analysis and experimental data.

Current leads cooling for the series-connected hybrid magnets

NASA Astrophysics Data System (ADS)

Bai, Hongyu; Marshall, William S.; Bird, Mark D.; Gavrilin, Andrew V.; Weijers, Hubertus W.

2014-01-01

Two Series-Connected Hybrid (SCH) magnets are being developed at the National High Magnetic Field Laboratory. Both SCH magnets combine a set of resistive Florida-Bitter coils with a superconducting outsert coil constructed of the cable-in-conduit conductor (CICC). The outsert coils of the two magnets employ 20 kA BSCCO HTS current leads for the power supply although they have different designs and cooling methods. The copper heat exchangers of the HTS current leads for the HZB SCH are cooled with forced flow helium at a supply temperature of 44 K, while the copper heat exchangers of HTS current leads for NHMFL SCH are cooled with liquid nitrogen at a temperature of 78 K in a self-demand boil-off mode. This paper presents the two cooling methods and their impacts on cryogenic systems. Their efficiencies and costs are compared and presented.

Drawing a different picture with pencil lead as matrix-assisted laser desorption/ionization matrix for fullerene derivatives.

PubMed

Nye, Leanne C; Hungerbühler, Hartmut; Drewello, Thomas

2018-02-01

Inspired by reports on the use of pencil lead as a matrix-assisted laser desorption/ionization matrix, paving the way towards matrix-free matrix-assisted laser desorption/ionization, the present investigation evaluates its usage with organic fullerene derivatives. Currently, this class of compounds is best analysed using the electron transfer matrix trans-2-[3-(4-tert-butylphenyl)-2-methyl-2-propenylidene] malononitrile (DCTB), which was employed as the standard here. The suitability of pencil lead was additionally compared to direct (i.e. no matrix) laser desorption/ionization-mass spectrometry. The use of (DCTB) was identified as the by far gentler method, producing spectra with abundant molecular ion signals and much reduced fragmentation. Analytically, pencil lead was found to be ineffective as a matrix, however, appears to be an extremely easy and inexpensive method for producing sodium and potassium adducts.

Working towards accreditation by the International Standards Organization 15189 Standard: how to validate an in-house developed method an example of lead determination in whole blood by electrothermal atomic absorption spectrometry.

PubMed

Garcia Hejl, Carine; Ramirez, Jose Manuel; Vest, Philippe; Chianea, Denis; Renard, Christophe

2014-09-01

Laboratories working towards accreditation by the International Standards Organization (ISO) 15189 standard are required to demonstrate the validity of their analytical methods. The different guidelines set by various accreditation organizations make it difficult to provide objective evidence that an in-house method is fit for the intended purpose. Besides, the required performance characteristics tests and acceptance criteria are not always detailed. The laboratory must choose the most suitable validation protocol and set the acceptance criteria. Therefore, we propose a validation protocol to evaluate the performance of an in-house method. As an example, we validated the process for the detection and quantification of lead in whole blood by electrothermal absorption spectrometry. The fundamental parameters tested were, selectivity, calibration model, precision, accuracy (and uncertainty of measurement), contamination, stability of the sample, reference interval, and analytical interference. We have developed a protocol that has been applied successfully to quantify lead in whole blood by electrothermal atomic absorption spectrometry (ETAAS). In particular, our method is selective, linear, accurate, and precise, making it suitable for use in routine diagnostics.

[Lead poisoning: towards a paleo-epidemiologic re-interpretation?].

PubMed

Bourdieu, Anne

2014-01-01

Lead is a major public health issue. Its use has been increasing since Neolithic times, climaxing in the Ancient Rome and the nineteenth century. Defining the frequency of plumbism before modern times proves to be a difficult matter because of its various and delayed symptoms, and of diagenetic processes affecting bones. After reviewing various methods of lead measurement in bone and tooth, we will expose ways to ascertain lead measurement interpretation in order to estimate the epidemiology of plumbism in ancient times.

Lead toxicity and endoscopic removal of ingested firearm cartridges.

PubMed

Hatten, B W; Bueso, A; Craven, P; Hendrickson, R G; Horowitz, B Z

2013-06-01

Lead toxicity from the ingestion of a lead foreign body has been described in several case reports. Management of ingested live ammunition presents its own challenges due to the risk of accidental discharge. A safe and effective method of retrieving a live cartridge must be considered. We present two cases of lead toxicity due to intact firearm cartridge ingestion with the removal of the cartridges via endoscopy. The first case is of severe pediatric lead toxicity due to the ingestion of 30-mm rifle cartridges. The second case is an adult ingestion of .22 caliber cartridges resulting in mild lead toxicity. These cases illustrate a diagnostic dilemma in both the diagnosis of lead toxicity and the removal of live ammunition from the stomach.

Lead foil wrapping of the plastic scintillators for the gamma ray detection: optical reflector or spectrum intensifier?

NASA Astrophysics Data System (ADS)

Taheri, A.; Askari, M.; Taghan Sasanpour, M.

2017-08-01

This paper studies the effect of lead wrapping on the response of the plastic scintillators as gamma detectors. Experimental tests and Geant4 simulations showed that lead wrapping cannot increase the gamma absorption efficiency of the detector but, as a reflector, it can improve the optical properties of the detector. The reflectivity of the lead foil as an optical reflector was determined equal to 66% using an experimental-simulation combined method. Based on the obtained results, the optical collection efficiency of the detector was also increased about 4% after employing the lead reflector.

Dual-acting of Hybrid Compounds - A New Dawn in the Discovery of Multi-target Drugs: Lead Generation Approaches.

PubMed

Abdolmaleki, Azizeh; Ghasemi, Jahan B

2017-01-01

Finding high quality beginning compounds is a critical job at the start of the lead generation stage for multi-target drug discovery (MTDD). Designing hybrid compounds as selective multitarget chemical entity is a challenge, opportunity, and new idea to better act against specific multiple targets. One hybrid molecule is formed by two (or more) pharmacophore group's participation. So, these new compounds often exhibit two or more activities going about as multi-target drugs (mtdrugs) and may have superior safety or efficacy. Application of integrating a range of information and sophisticated new in silico, bioinformatics, structural biology, pharmacogenomics methods may be useful to discover/design, and synthesis of the new hybrid molecules. In this regard, many rational and screening approaches have followed by medicinal chemists for the lead generation in MTDD. Here, we review some popular lead generation approaches that have been used for designing multiple ligands (DMLs). This paper focuses on dual- acting chemical entities that incorporate a part of two drugs or bioactive compounds to compose hybrid molecules. Also, it presents some of key concepts and limitations/strengths of lead generation methods by comparing combination framework method with screening approaches. Besides, a number of examples to represent applications of hybrid molecules in the drug discovery are included. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Standard methods for chemical analysis of steel, cast iron, open-hearth iron, and wrought iron

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1973-01-01

Methods are described for determining manganese, phosphorus, sulfur, selenium, copper, nickel, chromium, vanadium, tungsten, titanium, lead, boron, molybdenum ( alpha -benzoin oxime method), zirconium (cupferron --phosphate method), niobium and tantalum (hydrolysis with perchloric and sulfurous acids (gravimetric, titrimetric, and photometric methods)), and beryllium (oxide method). (DHM)

Determination of lead in bone tissues by axially viewed inductively coupled plasma multichannel-based emission spectrometry.

PubMed

Grotti, Marco; Abelmoschi, Maria Luisa; Dalla Riva, Simona; Soggia, Francesco; Frache, Roberto

2005-04-01

A new procedure for determining low levels of lead in bone tissues has been developed. After wet acid digestion in a pressurized microwave-heated system, the solution was analyzed by inductively coupled plasma multichannel-based emission spectrometry. Internal standardization using the Co 228.615 nm reference line was chosen as the optimal method to compensate for the matrix effects from the presence of calcium and nitric acid at high concentration levels. The detection limit of the procedure was 0.11 microg Pb g(-1) dry mass. Instrumental precision at the analytical concentration of approximately 10 microg l(-1) ranged from 6.1 to 9.4%. Precision of the sample preparation step was 5.4%. The concentration of lead in SRM 1486 (1.32+/-0.04 microg g(-1)) found using the new procedure was in excellent agreement with the certified level (1.335+/-0.014 microg g(-1)). Finally, the method was applied to determine the lead in various fish bone tissues, and the analytical results were found to be in good agreement with those obtained through differential pulse anodic stripping voltammetry. The method is therefore suitable for the reliable determination of lead at concentration levels of below 1 microg g(-1) in bone samples. Moreover, the multi-element capability of the technique allows us to simultaneously determine other major or trace elements in order to investigate inter-element correlation and to compute enrichment factors, making the proposed procedure particularly useful for investigating lead occurrence and pathways in fish bone tissues in order to find suitable biomarkers for the Antarctic marine environment.

Evaluation of a low-cost commercially available extraction device for assessing lead bioaccessibility in contaminated soils.

PubMed

Nelson, Clay M; Gilmore, Thomas M; Harrington, M; Scheckel, Kirk G; Miller, Bradley W; Bradham, Karen D

2013-03-01

The U.S. EPA's in vitro bioaccessibility (IVBA) method 9200.1-86 defines a validated analytical procedure for the determination of lead bioaccessibility in contaminated soils. The method requires the use of a custom-fabricated extraction device that uses a heated water bath for sample incubation. In an effort to improve ease of use, increase sample throughput, and reduce equipment acquisition and maintenance costs, an alternative low-cost, commercially available extraction device capable of sample incubation via heated air and end-over-end rotation was evaluated. An intra-laboratory study was conducted to compare lead bioaccessibility values derived using the two extraction devices. IVBA values were not statistically different (α = 0.05) between the two extraction devices for any of the soils (n = 6) evaluated in this study, with an average difference in mean lead IVBA of 0.8% (s.d. = 0.5%). The commercially available extraction device was able to generate accurate lead IVBA data as compared to the U.S. EPA's expected value for a National Institute of Standards and Technology standard reference material soil. The relative percent differences between high and low IVBA values for each soil, a measure of instrument precision, were also not statistically different (α = 0.05) between the two extraction devices. The statistical agreement of lead IVBA values observed using the two extraction devices supports the use of a low-cost, commercially available extraction device as a reliable alternative to a custom-fabricated device as required by EPA method 9200.1-86.

Boundary and Interface Conditions for High Order Finite Difference Methods Applied to the Euler and Navier-Strokes Equations

NASA Technical Reports Server (NTRS)

Nordstrom, Jan; Carpenter, Mark H.

1998-01-01

Boundary and interface conditions for high order finite difference methods applied to the constant coefficient Euler and Navier-Stokes equations are derived. The boundary conditions lead to strict and strong stability. The interface conditions are stable and conservative even if the finite difference operators and mesh sizes vary from domain to domain. Numerical experiments show that the new conditions also lead to good results for the corresponding nonlinear problems.

Compressed domain ECG biometric with two-lead features

NASA Astrophysics Data System (ADS)

Lee, Wan-Jou; Chang, Wen-Whei

2016-07-01

This study presents a new method to combine ECG biometrics with data compression within a common JPEG2000 framework. We target the two-lead ECG configuration that is routinely used in long-term heart monitoring. Incorporation of compressed-domain biometric techniques enables faster person identification as it by-passes the full decompression. Experiments on public ECG databases demonstrate the validity of the proposed method for biometric identification with high accuracies on both healthy and diseased subjects.

Method of making a non-lead hollow point bullet

DOEpatents

Vaughn, Norman L.; Lowden, Richard A.

2003-10-07

The method of making a non-lead hollow point bullet has the steps of a) compressing an unsintered powdered metal composite core into a jacket, b) punching a hollow cavity tip portion into the core, c) seating an insert, the insert having a hollow point tip and a tail protrusion, on top of the core such that the tail protrusion couples with the hollow cavity tip portion, and d) swaging the open tip of the jacket.

Experimental study of flow separation control on a low- Re airfoil using leading-edge protuberance method

NASA Astrophysics Data System (ADS)

Zhang, M. M.; Wang, G. F.; Xu, J. Z.

2014-04-01

An experimental study of flow separation control on a low- Re c airfoil was presently investigated using a newly developed leading-edge protuberance method, motivated by the improvement in the hydrodynamics of the giant humpback whale through its pectoral flippers. Deploying this method, the control effectiveness of the airfoil aerodynamics was fully evaluated using a three-component force balance, leading to an effectively impaired stall phenomenon and great improvement in the performances within the wide post-stall angle range (22°-80°). To understand the flow physics behind, the vorticity field, velocity field and boundary layer flow field over the airfoil suction side were examined using a particle image velocimetry and an oil-flow surface visualization system. It was found that the leading-edge protuberance method, more like low-profile vortex generator, effectively modified the flow pattern of the airfoil boundary layer through the chordwise and spanwise evolutions of the interacting streamwise vortices generated by protuberances, where the separation of the turbulent boundary layer dominated within the stall region and the rather strong attachment of the laminar boundary layer still existed within the post-stall region. The characteristics to manipulate the flow separation mode of the original airfoil indicated the possibility to further optimize the control performance by reasonably designing the layout of the protuberances.

Sea Ice Freeboard and Thickness from the 2013 IceBridge ATM and DMS Data in Ross Sea, Antarctica

NASA Astrophysics Data System (ADS)

Xie, H.; Tian, L.; Tang, J.; Ackley, S. F.

2016-12-01

In November (20, 21, 27, and 28) 2013, NASA's IceBridge mission flew over the Ross Sea, Antarctica and collected important sea ice data with the ATM and DMS for the first time. We will present our methods to derive the local sea level and total freeboard for ice thickness retrieval from these two datasets. The methods include (1) leads classification from DMS data using an automated lead detection method, (2) potential leads from the reflectance of less than 0.25 from the ATM laser shots of L1B data, (3) local sea level retrieval based on these qualified ATM laser shots (L1B) within the DMS-derived leads (after outliers removal from the mean ± 2 standard deviation of these ATM elevations), (4) establishment of an empirical equation of local sea level as a function of distance from the starting point of each IceBridge flight, (5) total freeboard retrieval from the ATM L2 elevations by subtracting the local sea level derived from the empirical equation, and (6) ice thickness retrieval. The ice thickness derived from this method will be analyzed and compared with ICESat data (2003-2009) and other available data for the same region at the similar time period. Possible change and potential reasons will be identified and discussed.

Detection of lead(II) ions with a DNAzyme and isothermal strand displacement signal amplification.

PubMed

Li, Wenying; Yang, Yue; Chen, Jian; Zhang, Qingfeng; Wang, Yan; Wang, Fangyuan; Yu, Cong

2014-03-15

A DNAzyme based method for the sensitive and selective quantification of lead(II) ions has been developed. A DNAzyme that requires Pb(2+) for activation was selected. An RNA containing DNA substrate was cleaved by the DNAzyme in the presence of Pb(2+). The 2',3'-cyclic phosphate of the cleaved 5'-part of the substrate was efficiently removed by Exonuclease III. The remaining part of the single stranded DNA (9 or 13 base long) was subsequently used as the primer for the strand displacement amplification reaction (SDAR). The method is highly sensitive, 200 pM lead(II) could be easily detected. A number of interference ions were tested, and the sensor showed good selectivity. Underground water samples were also tested, which demonstrated the feasibility of the current approach for real sample applications. It is feasible that our method could be used for DNAzyme or aptazyme based new sensing method developments for the quantification of other target analytes with high sensitivity and selectivity. © 2013 Elsevier B.V. All rights reserved.

Novel non-invasive algorithm to identify the origins of re-entry and ectopic foci in the atria from 64-lead ECGs: A computational study.

PubMed

Alday, Erick A Perez; Colman, Michael A; Langley, Philip; Zhang, Henggui

2017-03-01

Atrial tachy-arrhytmias, such as atrial fibrillation (AF), are characterised by irregular electrical activity in the atria, generally associated with erratic excitation underlain by re-entrant scroll waves, fibrillatory conduction of multiple wavelets or rapid focal activity. Epidemiological studies have shown an increase in AF prevalence in the developed world associated with an ageing society, highlighting the need for effective treatment options. Catheter ablation therapy, commonly used in the treatment of AF, requires spatial information on atrial electrical excitation. The standard 12-lead electrocardiogram (ECG) provides a method for non-invasive identification of the presence of arrhythmia, due to irregularity in the ECG signal associated with atrial activation compared to sinus rhythm, but has limitations in providing specific spatial information. There is therefore a pressing need to develop novel methods to identify and locate the origin of arrhythmic excitation. Invasive methods provide direct information on atrial activity, but may induce clinical complications. Non-invasive methods avoid such complications, but their development presents a greater challenge due to the non-direct nature of monitoring. Algorithms based on the ECG signals in multiple leads (e.g. a 64-lead vest) may provide a viable approach. In this study, we used a biophysically detailed model of the human atria and torso to investigate the correlation between the morphology of the ECG signals from a 64-lead vest and the location of the origin of rapid atrial excitation arising from rapid focal activity and/or re-entrant scroll waves. A focus-location algorithm was then constructed from this correlation. The algorithm had success rates of 93% and 76% for correctly identifying the origin of focal and re-entrant excitation with a spatial resolution of 40 mm, respectively. The general approach allows its application to any multi-lead ECG system. This represents a significant extension to our previously developed algorithms to predict the AF origins in association with focal activities.

Gamma-Ray Dose Measurement with Radio-Photoluminescence Glass Dosimeter in Mixed Radiation Field for BNCT

NASA Astrophysics Data System (ADS)

Hiramatsu, K.; Yoshihashi, S.; Kusaka, S.; Sato, F.; Hoashi, E.; Murata, I.

2017-09-01

Accelerator based neutron sources (ABNS) are being developed as the next generation neutron irradiation system for BNCT. From the ABNS, unnecessary gamma-rays will be generated by neutron capture reactions, as well as fast neutrons. To control the whole-body radiation dose to the patient, measurement of gamma-ray dose in the irradiation room is necessary. In this study, the objective is to establish a method to measure gamma-ray dose separately in a neutron/gamma mixed field by using RPL glass dosimeter. For this purpose, we proposed a lead filter method which uses a pair of RPL glasses with and without a lead filter outside. In order to realize this method, the basic characteristics of glass dosimeter was verified in the gamma-ray field, before adapting it in the mixture field. From the result of the experiment using the lead filter, the simulation result especially for the case with a lead filter overestimated the absorbed does obtained from measurement. We concluded that the reason of the discrepancy is caused by existence of gradient of the dose distribution in the glass, and the difference of sensitivity to low-energy photon between measurement and theory.

Application of six sigma and AHP in analysis of variable lead time calibration process instrumentation

NASA Astrophysics Data System (ADS)

Rimantho, Dino; Rahman, Tomy Abdul; Cahyadi, Bambang; Tina Hernawati, S.

2017-02-01

Calibration of instrumentation equipment in the pharmaceutical industry is an important activity to determine the true value of a measurement. Preliminary studies indicated that occur lead-time calibration resulted in disruption of production and laboratory activities. This study aimed to analyze the causes of lead-time calibration. Several methods used in this study such as, Six Sigma in order to determine the capability process of the calibration instrumentation of equipment. Furthermore, the method of brainstorming, Pareto diagrams, and Fishbone diagrams were used to identify and analyze the problems. Then, the method of Hierarchy Analytical Process (AHP) was used to create a hierarchical structure and prioritize problems. The results showed that the value of DPMO around 40769.23 which was equivalent to the level of sigma in calibration equipment approximately 3,24σ. This indicated the need for improvements in the calibration process. Furthermore, the determination of problem-solving strategies Lead Time Calibration such as, shortens the schedule preventive maintenance, increase the number of instrument Calibrators, and train personnel. Test results on the consistency of the whole matrix of pairwise comparisons and consistency test showed the value of hierarchy the CR below 0.1.

Thermal Cycling Life Prediction of Sn-3.0Ag-0.5Cu Solder Joint Using Type-I Censored Data

PubMed Central

Mi, Jinhua; Yang, Yuan-Jian; Huang, Hong-Zhong

2014-01-01

Because solder joint interconnections are the weaknesses of microelectronic packaging, their reliability has great influence on the reliability of the entire packaging structure. Based on an accelerated life test the reliability assessment and life prediction of lead-free solder joints using Weibull distribution are investigated. The type-I interval censored lifetime data were collected from a thermal cycling test, which was implemented on microelectronic packaging with lead-free ball grid array (BGA) and fine-pitch ball grid array (FBGA) interconnection structures. The number of cycles to failure of lead-free solder joints is predicted by using a modified Engelmaier fatigue life model and a type-I censored data processing method. Then, the Pan model is employed to calculate the acceleration factor of this test. A comparison of life predictions between the proposed method and the ones calculated directly by Matlab and Minitab is conducted to demonstrate the practicability and effectiveness of the proposed method. At last, failure analysis and microstructure evolution of lead-free solders are carried out to provide useful guidance for the regular maintenance, replacement of substructure, and subsequent processing of electronic products. PMID:25121138

DOE Office of Scientific and Technical Information (OSTI.GOV)

Craswell, P.W.; Price, J.; Boyle, P.D.

EDTA (calcium disodium edetate) lead mobilization and x-ray fluorescence (XRF) finger bone lead tests were done in 42 patients with chronic renal failure and without persisting lead intoxication. Nineteen of 23 patients with gout and 8 of 19 without gout had positive EDTA lead mobilization tests. Those patients with gout excreted significantly more excess lead chelate than those without gout. In the gout group 17 patients denied any childhood or industrial exposure to lead. They had a greater number of positive tests and excreted significantly more excess lead chelate than 14 patients with neither gout nor lead exposure. These resultsmore » confirm that gout in the presence of chronic renal failure is a useful marker of chronic lead poisoning. Of 27 patients with positive lead mobilization tests, only 13 had elevated XRF finger bone lead concentrations (sensitivity 48%). Three of 15 patients with negative lead mobilization tests had elevated XRF finger bone lead concentrations (specificity 80%). Although the XRF finger bone lead test is a convenient noninvasive addition to the diagnostic evaluation of patients with chronic renal failure and gout, its application is limited due to the lack of sensitivity of the method.« less

Method for fabricating fan-fold shielded electrical leads

DOEpatents

Rohatgi, R.R.; Cowan, T.E.

1994-12-27

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate. 3 figures.

Extraction of lead and ridge characteristics from SAR images of sea ice

NASA Technical Reports Server (NTRS)

Vesecky, John F.; Smith, Martha P.; Samadani, Ramin

1990-01-01

Image-processing techniques for extracting the characteristics of lead and pressure ridge features in SAR images of sea ice are reported. The methods are applied to a SAR image of the Beaufort Sea collected from the Seasat satellite on October 3, 1978. Estimates of lead and ridge statistics are made, e.g., lead and ridge density (number of lead or ridge pixels per unit area of image) and the distribution of lead area and orientation as well as ridge length and orientation. The information derived is useful in both ice science and polar operations for such applications as albedo and heat and momentum transfer estimates, as well as ship routing and offshore engineering.

Method for fabricating fan-fold shielded electrical leads

DOEpatents

Rohatgi, Rajeev R.; Cowan, Thomas E.

1994-01-01

Fan-folded electrical leads made from copper cladded Kapton, for example, with the copper cladding on one side serving as a ground plane and the copper cladding on the other side being etched to form the leads. The Kapton is fan folded with the leads located at the bottom of the fan-folds. Electrical connections are made by partially opening the folds of the fan and soldering, for example, the connections directly to the ground plane and/or the lead. The fan folded arrangement produces a number of advantages, such as electrically shielding the leads from the environment, is totally non-magnetic, and has a very low thermal conductivity, while being easy to fabricate.

Technology-based vs. traditional instruction. A comparison of two methods for teaching the skill of performing a 12-lead ECG.

PubMed

Jeffries, Pamela R; Woolf, Shirley; Linde, Beverly

2003-01-01

The purpose of this study was to compare the effectiveness of an interactive, multimedia CD-ROM with traditional methods of teaching the skill of performing a 12-lead ECG. A randomized pre/posttest experimental design was used. Seventy-seven baccalaureate nursing students in a required, senior-level critical-care course at a large midwestern university were recruited for the study. Two teaching methods were compared. The traditional method included a self-study module, a brief lecture and demonstration by an instructor, and hands-on experience using a plastic manikin and a real 12-lead ECG machine in the learning laboratory. The second method covered the same content using an interactive, multimedia CD-ROM embedded with virtual reality and supplemented with a self-study module. There were no significant (p < .05) baseline differences in pretest scores between the two groups and no significant differences by group in cognitive gains, student satisfaction with their learning method, or perception of self-efficacy in performing the skill. Overall results indicated that both groups were satisfied with their instructional method and were similar in their ability to demonstrate the skill correctly on a live, simulated patient. This evaluation study is a beginning step to assess new and potentially more cost-effective teaching methods and their effects on student learning outcomes and behaviors, including the transfer of skill acquisition via a computer simulation to a real patient.

Agile Methods in Air Force Sustainment: Status and Outlook

DTIC Science & Technology

2014-10-01

manage for it through iterations, anticipation and adaptation  unleash creativity and innovation by recognizing that individuals are the ultimate...073561993X X X Agile Project Management : Creating Innovative Products – 2nd Edition Jim Highsmith ISBN 0321658396 X Agile Retrospectives...X Leading Change John Kotter ISBN 0875847471 X Leading Geeks: How to Manage and Lead the People Who Deliver Technology Paul Glen ISBN

16 CFR 1500.90 - Procedures and requirements for exclusions from lead limits under section 101(b) of the Consumer...

Code of Federal Regulations, 2014 CFR

2014-01-01

... inaccessible to a child or prevent the absorption of any lead in the human body through normal and reasonably...) Measurement. For purposes of paragraph (b)(1)(i)(C) of this section, there is no measurable adverse effect on... method of measurement other than blood lead levels if it determines, after notice and a hearing, that...

Method to pattern <10 micrometer conducting and passivating features on 3D substrates for implantable devices

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolosa, Vanessa; Pannu, Satinderpall S.; Sheth, Heeral

2017-07-04

An implantable device has a cylindrical base, at least one electrode on the cylindrical base, at least one electrically conducting lead on the cylindrical base connected to the electrode wherein the electrically conducting lead has a feature size of <10 micrometers. A protective coating on the cylindrical base covers the at least one electrically conducting lead.

40 CFR Appendix G to Part 50 - Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From...

Code of Federal Regulations, 2012 CFR

2012-07-01

... obtains filters with a lead content of 75 µg/filter. It is important that the variation in lead content... important to keep the sample covered so that corrosion products—formed on fume hood surfaces which may... National Science Foundation for publications, 1976. 3. Zdrojewski, A. et al. “The Accurate Measurement of...

40 CFR Appendix G to Part 50 - Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From...

Code of Federal Regulations, 2011 CFR

2011-07-01

... obtains filters with a lead content of 75 µg/filter. It is important that the variation in lead content... important to keep the sample covered so that corrosion products—formed on fume hood surfaces which may... National Science Foundation for publications, 1976. 3. Zdrojewski, A. et al. “The Accurate Measurement of...

40 CFR Appendix G to Part 50 - Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From...

Code of Federal Regulations, 2013 CFR

2013-07-01

... obtains filters with a lead content of 75 µg/filter. It is important that the variation in lead content... important to keep the sample covered so that corrosion products—formed on fume hood surfaces which may... National Science Foundation for publications, 1976. 3. Zdrojewski, A. et al. “The Accurate Measurement of...

Occupational Determinants of Cumulative Lead Exposure: Analysis of Bone Lead Among Men in the VA Normative Aging Study

PubMed Central

Ji, John S.; Schwartz, Joel; Sparrow, David; Hu, Howard; Weisskopf, Marc G.

2014-01-01

Objectives To examine the relation between occupation and cumulative lead exposure—assessed by measuring bone lead—in a community-dwelling population Method We measured bone lead concentration with K-shell X-Ray Fluorescence in 1,320 men in the Normative Aging Study. We categorized job titles into 14 broad US Census Bureau categories. We used ordinary least squares regression to estimate bone lead by job categories adjusted for other predictors. Results Service Workers, Construction and Extractive Craft Workers, and Installation, Maintenance and Repair Craft Workers had the highest bone lead concentrations. Including occupations significantly improved the overall model (p<0.001) and reduced by −15% to −81% the association between bone lead and education categories. Conclusion Occupation significantly predicts cumulative lead exposure in a community-dwelling population, and accounts for a large proportion of the association between education and bone lead. PMID:24709766

Anaerobic microbial dissolution of lead and production of organic acids

DOEpatents

Francis, A.J.; Dodge, C.; Chendrayan, K.

1986-02-28

The present invention relates to a method of solubilizing lead, in the form of lead oxide, found in industrial wastes, before these wastes are dumped into the environment. The lead is solubilized by dissolving the lead oxide in the wastes through contact with an anaerobic bacterial culture containing the bacterium ATCC No. 53464. The solubilized lead can then be removed from the wastes by chemical separation. It could also be removed by extending the contact period with the bacterial culture. As the culture grows, the solubilized lead is removed from the wastes by bioaccumulation by the microorganism or by immobilization by a polymer-like material produced by the microorganism. At this point, the lead is then removed from the wastes when the waste material is separated from the bacterial culture. If desired, the bacterial culture could be digested at this point to yield relatively pure lead for further industrial use.

Kinetics of oil saponification by lead salts in ancient preparations of pharmaceutical lead plasters and painting lead mediums.

PubMed

Cotte, M; Checroun, E; Susini, J; Dumas, P; Tchoreloff, P; Besnard, M; Walter, Ph

2006-12-15

Lead soaps can be found in archaeological cosmetics as well as in oil paintings, as product of interactions of lead salts with oil. In this context, a better understanding of the formation of lead soaps allows a follow-up of the historical evolution of preparation recipes and provides new insights into conservation conditions. First, ancient recipes of both pharmaceutical lead plasters and painting lead mediums, mixtures of oil and lead salts, were reconstructed. The ester saponification by lead salts is determined by the preparation parameters which were quantified by FT-IR spectrometry. In particular, ATR/FT-IR spectrometer was calibrated by the standard addition method to quantitatively follow the kinetics of this reaction. The influence of different parameters such as temperature, presence of water and choice of lead salts was assessed: the saponification is clearly accelerated by water and heating. This analysis provides chemical explanations to the historical evolution of cosmetic and painting preparation recipes.

High-Intensity Targeted Screening for Elevated Blood Lead Levels Among Children in 2 Inner-City Chicago Communities

PubMed Central

Dignam, Timothy A.; Evens, Anne; Eduardo, Eduard; Ramirez, Shokufeh M.; Caldwell, Kathleen L.; Kilpatrick, Nikki; Noonan, Gary P.; Flanders, W. Dana; Meyer, Pamela A.; McGeehin, Michael A.

2004-01-01

Objectives. We assessed the prevalence of elevated blood lead levels (≥ 10 micrograms of lead per deciliter of blood), risk factors, and previous blood lead testing among children in 2 high-risk Chicago, Ill, communities. Methods. Through high-intensity targeted screening, blood lead levels were tested and risks were assessed among a representative sample of children aged 1 to 5 years who were at risk for lead exposure. Results. Of the 539 children who were tested, 27% had elevated blood lead levels, and 61% had never been tested previously. Elevated blood lead levels were associated with chipped exterior house paint. Conclusions. Most of the children who lived in these communities—where the prevalence for elevated blood lead levels among children was 12 times higher than the national prevalence—were not tested for lead poisoning. Our findings highlight the need for targeted community outreach that includes testing blood lead levels in accordance with the American Academy of Pediatrics’ recommendations. PMID:15514235

Determination of cadmium and lead in table salt by sequential multi-element flame atomic absorption spectrometry.

PubMed

Amorim, Fábio A C; Ferreira, Sérgio L C

2005-02-28

In the present paper, a simultaneous pre-concentration procedure for the sequential determination of cadmium and lead in table salt samples using flame atomic absorption spectrometry is proposed. This method is based on the liquid-liquid extraction of cadmium(II) and lead(II) ions as dithizone complexes and direct aspiration of the organic phase for the spectrometer. The sequential determination of cadmium and lead is possible using a computer program. The optimization step was performed by a two-level fractional factorial design involving the variables: pH, dithizone mass, shaking time after addition of dithizone and shaking time after addition of solvent. In the studied levels these variables are not significant. The experimental conditions established propose a sample volume of 250mL and the extraction process using 4.0mL of methyl isobutyl ketone. This way, the procedure allows determination of cadmium and lead in table salt samples with a pre-concentration factor higher than 80, and detection limits of 0.3ngg(-1) for cadmium and 4.2ngg(-1) for lead. The precision expressed as relative standard deviation (n = 10) were 5.6 and 2.6% for cadmium concentration of 2 and 20ngg(-1), respectively, and of 3.2 and 1.1% for lead concentration of 20 and 200ngg(-1), respectively. Recoveries of cadmium and lead in several samples, measured by standard addition technique, proved also that this procedure is not affected by the matrix and can be applied satisfactorily for the determination of cadmium and lead in saline samples. The method was applied for the evaluation of the concentration of cadmium and lead in table salt samples consumed in Salvador City, Bahia, Brazil.

Practice-Tailored Facilitation to Improve Pediatric Preventive Care Delivery: A Randomized Trial

PubMed Central

Schiltz, Nicholas K.; Sattar, Abdus; Stange, Kurt C.; Nevar, Ann H.; Davey, Christina; Ferretti, Gerald A.; Howell, Diana E.; Strosaker, Robyn; Vavrek, Pamela; Bader, Samantha; Ruhe, Mary C.; Cuttler, Leona

2014-01-01

OBJECTIVE: Evolving primary care models require methods to help practices achieve quality standards. This study assessed the effectiveness of a Practice-Tailored Facilitation Intervention for improving delivery of 3 pediatric preventive services. METHODS: In this cluster-randomized trial, a practice facilitator implemented practice-tailored rapid-cycle feedback/change strategies for improving obesity screening/counseling, lead screening, and dental fluoride varnish application. Thirty practices were randomized to Early or Late Intervention, and outcomes assessed for 16 419 well-child visits. A multidisciplinary team characterized facilitation processes by using comparative case study methods. RESULTS: Baseline performance was as follows: for Obesity: 3.5% successful performance in Early and 6.3% in Late practices, P = .74; Lead: 62.2% and 77.8% success, respectively, P = .11; and Fluoride: <0.1% success for all practices. Four months after randomization, performance rose in Early practices, to 82.8% for Obesity, 86.3% for Lead, and 89.1% for Fluoride, all P < .001 for improvement compared with Late practices’ control time. During the full 6-month intervention, care improved versus baseline in all practices, for Obesity for Early practices to 86.5%, and for Late practices 88.9%; for Lead for Early practices to 87.5% and Late practices 94.5%; and for Fluoride, for Early practices to 78.9% and Late practices 81.9%, all P < .001 compared with baseline. Improvements were sustained 2 months after intervention. Successful facilitation involved multidisciplinary support, rapid-cycle problem solving feedback, and ongoing relationship-building, allowing individualizing facilitation approach and intensity based on 3 levels of practice need. CONCLUSIONS: Practice-tailored Facilitation Intervention can lead to substantial, simultaneous, and sustained improvements in 3 domains, and holds promise as a broad-based method to advance pediatric preventive care. PMID:24799539

Soil Lead and Children’s Blood Lead Disparities in Pre- and Post-Hurricane Katrina New Orleans (USA)

PubMed Central

Mielke, Howard W.; Gonzales, Christopher R.; Powell, Eric T.

2017-01-01

This study appraises New Orleans soil lead and children’s lead exposure before and ten years after Hurricane Katrina flooded the city. Introduction: Early childhood exposure to lead is associated with lifelong and multiple health, learning, and behavioral disorders. Lead exposure is an important factor hindering the long-term resilience and sustainability of communities. Lead exposure disproportionately affects low socioeconomic status of communities. No safe lead exposure is known and the common intervention is not effective. An essential responsibility of health practitioners is to develop an effective primary intervention. Methods: Pre- and post-Hurricane soil lead and children’s blood lead data were matched by census tract communities. Soil lead and blood lead data were described, mapped, blood lead graphed as a function of soil lead, and Multi-Response Permutation Procedures statistics established disparities. Results: Simultaneous decreases occurred in soil lead accompanied by an especially large decline in children’s blood lead 10 years after Hurricane Katrina. Exposure disparities still exist between children living in the interior and outer areas of the city. Conclusions: At the scale of a city, this study demonstrates that decreasing soil lead effectively reduces children’s blood lead. Primary prevention of lead exposure can be accomplished by reducing soil lead in the urban environment. PMID:28417939

Soil Lead and Children's Blood Lead Disparities in Pre- and Post-Hurricane Katrina New Orleans (USA).

PubMed

Mielke, Howard W; Gonzales, Christopher R; Powell, Eric T

2017-04-12

This study appraises New Orleans soil lead and children's lead exposure before and ten years after Hurricane Katrina flooded the city. Introduction : Early childhood exposure to lead is associated with lifelong and multiple health, learning, and behavioral disorders. Lead exposure is an important factor hindering the long-term resilience and sustainability of communities. Lead exposure disproportionately affects low socioeconomic status of communities. No safe lead exposure is known and the common intervention is not effective. An essential responsibility of health practitioners is to develop an effective primary intervention. Methods : Pre- and post-Hurricane soil lead and children's blood lead data were matched by census tract communities. Soil lead and blood lead data were described, mapped, blood lead graphed as a function of soil lead, and Multi-Response Permutation Procedures statistics established disparities. Results : Simultaneous decreases occurred in soil lead accompanied by an especially large decline in children's blood lead 10 years after Hurricane Katrina. Exposure disparities still exist between children living in the interior and outer areas of the city. Conclusions : At the scale of a city, this study demonstrates that decreasing soil lead effectively reduces children's blood lead. Primary prevention of lead exposure can be accomplished by reducing soil lead in the urban environment.

Cosmic ray radiography of the damaged cores of the Fukushima reactors

DOE PAGES

Borozdin, Konstantin; Greene, Steven; Lukić, Zarija; ...

2012-10-11

The passage of muons through matter is dominated by the Coulomb interaction with electrons and nuclei. The interaction with the electrons leads to continuous energy loss and stopping of the muons. The interaction with nuclei leads to angle “diffusion.” Two muon-imaging methods that use flux attenuation and multiple Coulomb scattering of cosmic-ray muons are being studied as tools for diagnosing the damaged cores of the Fukushima reactors. Here, we compare these two methods. We conclude that the scattering method can provide detailed information about the core. Lastly, attenuation has low contrast and little sensitivity to the core.

Approximation methods for control of acoustic/structure models with piezoceramic actuators

NASA Technical Reports Server (NTRS)

Banks, H. T.; Fang, W.; Silcox, R. J.; Smith, R. C.

1991-01-01

The active control of acoustic pressure in a 2-D cavity with a flexible boundary (a beam) is considered. Specifically, this control is implemented via piezoceramic patches on the beam which produces pure bending moments. The incorporation of the feedback control in this manner leads to a system with an unbounded input term. Approximation methods in this manner leads to a system with an unbounded input term. Approximation methods in the context of linear quadratic regulator (LQR) state space control formulation are discussed and numerical results demonstrating the effectiveness of this approach in computing feedback controls for noise reduction are presented.

The magnetic lead field theorem in the quasi-static approximation and its use for magnetoencephalography forward calculation in realistic volume conductors.

PubMed

Nolte, Guido

2003-11-21

The equation for the magnetic lead field for a given magnetoencephalography (MEG) channel is well known for arbitrary frequencies omega but is not directly applicable to MEG in the quasi-static approximation. In this paper we derive an equation for omega = 0 starting from the very definition of the lead field instead of using Helmholtz's reciprocity theorems. The results are (a) the transpose of the conductivity times the lead field is divergence-free, and (b) the lead field differs from the one in any other volume conductor by a gradient of a scalar function. Consequently, for a piecewise homogeneous and isotropic volume conductor, the lead field is always tangential at the outermost surface. Based on this theoretical result, we formulated a simple and fast method for the MEG forward calculation for one shell of arbitrary shape: we correct the corresponding lead field for a spherical volume conductor by a superposition of basis functions, gradients of harmonic functions constructed here from spherical harmonics, with coefficients fitted to the boundary conditions. The algorithm was tested for a prolate spheroid of realistic shape for which the analytical solution is known. For high order in the expansion, we found the solutions to be essentially exact and for reasonable accuracies much fewer multiplications are needed than in typical implementations of the boundary element methods. The generalization to more shells is straightforward.

Simultaneous determination of thorium, niobium, lead, and zinc by photon-induced x-ray fluorescence of lateritic material

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaBrecque, J.J.; Adames, D.; Parker, W.C.

1981-01-01

A rapid method is presented for the simultaneous determinations of thorium, niobium, lead, and zinc in lateritic material from Cerro Impacto, Estado Bolivar, Venezuela. This technique uses a PDP - 11/05 processor - based photon induced x-ray fluorescence system. The total variations of approximately 5% for concentrations of approximately 1 and 10% for concentrations of approximately 0.1% were obtained with only 500 s of fluorescent time. The values obtained by this method were in agreement with values measured by conventional flame atomic absorption spectroscopy for lead and zinc. The values for thorium measured were in agreement with the reported valuesmore » for the reference materials supplied by NBL.« less

SU-E-J-110: TG 51 Dosimetry : With Or Without Lead

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shah, M

TG-51 Dosimetry: With or Without Lead. Purpose: In this project, an analytical method has been introduced for adjustment of the TG-51 recommended KQ in order to produce accurate dosimetric data for high energy photons without the lead foil. Methods: These investigations were performed using a 30 cm × 30 cm × 30 cm CIVCO water tank, A12 EXRADIN Water proof Farmer Chamber, a Standard Imaging MAX 4000 electrometer, and 1 mm thick lead foil from Standard Imaging. Complete TG-51 was performed every month with and without lead. The results were analyzed and an analytical model has been developed for comparingmore » the values of KQ. TG-51 Table I was used to obtain KQ values. Results: The dosimetric evaluations were obtained for Varian Linear accelerators Model 21ix and 21ex. These results indicates that the measured data with lead foil in place as recommended by TG-51 is in excellent agreement (within 0.1%) with the calculated data obtained by the new model, from our dosimetry data without-lead. If equation 15 of the TG-51 report is used without any adjustments, it will lead to differences of about 1.6 % (on the average) in relative data which will Resultin differences of about 0.3 % (on the average) in the KQ Values. The KQ value for 18 MV obtained consistently with the equation of TG-51 “with lead” and “without lead” were 0.971 and 0.974, respectively. The 0.3 % higher results for KQ without lead eventually will lead to 0.3% larger output. However, by considering this model the KQ value was found to be 0.971 for dosimetry without lead. Conclusion: The analytical model that was introduced in this project was able to reproduce the dosimetric data of the high energy linear accelerators to within 0.1% without the use of the lead foil.« less

Present and future contraception: does discovery of targets lead to new contraceptives?

PubMed

Jensen, Jeffrey T

2015-01-01

Although many highly effective methods of reversible contraception are available, high rates of unintended pregnancy and abortion provide evidence that current methods do not meet the needs of all couples. In recent years, a number of highly specific targets have been identified in key pathways that regulate the development of male and female gametes. Support for development of novel approaches has moved from industry to governmental and foundation funders. Continued public funding will be needed to move promising leads into clinical trials.

Three-Jet Production in Electron-Positron Collisions at Next-to-Next-to-Leading Order Accuracy

NASA Astrophysics Data System (ADS)

Del Duca, Vittorio; Duhr, Claude; Kardos, Adam; Somogyi, Gábor; Trócsányi, Zoltán

2016-10-01

We introduce a completely local subtraction method for fully differential predictions at next-to-next-to-leading order (NNLO) accuracy for jet cross sections and use it to compute event shapes in three-jet production in electron-positron collisions. We validate our method on two event shapes, thrust and C parameter, which are already known in the literature at NNLO accuracy and compute for the first time oblateness and the energy-energy correlation at the same accuracy.

Three-Jet Production in Electron-Positron Collisions at Next-to-Next-to-Leading Order Accuracy.

PubMed

Del Duca, Vittorio; Duhr, Claude; Kardos, Adam; Somogyi, Gábor; Trócsányi, Zoltán

2016-10-07

We introduce a completely local subtraction method for fully differential predictions at next-to-next-to-leading order (NNLO) accuracy for jet cross sections and use it to compute event shapes in three-jet production in electron-positron collisions. We validate our method on two event shapes, thrust and C parameter, which are already known in the literature at NNLO accuracy and compute for the first time oblateness and the energy-energy correlation at the same accuracy.

Multigrid method for stability problems

NASA Technical Reports Server (NTRS)

Ta'asan, Shlomo

1988-01-01

The problem of calculating the stability of steady state solutions of differential equations is addressed. Leading eigenvalues of large matrices that arise from discretization are calculated, and an efficient multigrid method for solving these problems is presented. The resulting grid functions are used as initial approximations for appropriate eigenvalue problems. The method employs local relaxation on all levels together with a global change on the coarsest level only, which is designed to separate the different eigenfunctions as well as to update their corresponding eigenvalues. Coarsening is done using the FAS formulation in a nonstandard way in which the right-hand side of the coarse grid equations involves unknown parameters to be solved on the coarse grid. This leads to a new multigrid method for calculating the eigenvalues of symmetric problems. Numerical experiments with a model problem are presented which demonstrate the effectiveness of the method.

Two-step extraction method for lead isotope fractionation to reveal anthropogenic lead pollution.

PubMed

Katahira, Kenshi; Moriwaki, Hiroshi; Kamura, Kazuo; Yamazaki, Hideo

2018-05-28

This study developed the 2-step extraction method which eluted the Pb adsorbing on the surface of sediments in the first solution by aqua regia and extracted the Pb absorbed inside particles into the second solution by mixed acid of nitric acid, hydrofluoric acid and hydrogen peroxide solution. We applied the method to sediments in the enclosed water area and found out that the isotope ratios of Pb in the second solution represented those of natural origin. This advantage of the method makes it possible to distinguish the Pb between natural origin and anthropogenic source on the basis of the isotope ratios. The results showed that the method was useful to discuss the Pb sources and that anthropogenic Pb in the sediment samples analysed was mainly derived from China because of transboundary air pollution.

A stable second order method for training back propagation networks

NASA Technical Reports Server (NTRS)

Nachtsheim, Philip R.

1993-01-01

A simple method for improving the learning rate of the back-propagation algorithm is described. The basis of the method is that approximate second order corrections can be incorporated in the output units. The extended method leads to significant improvements in the convergence rate.

75 FR 45627 - Office of Research and Development; Ambient Air Monitoring Reference and Equivalent Methods...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-03

... Monitoring Reference and Equivalent Methods: Designation of One New Equivalent Method AGENCY: Environmental Protection Agency. ACTION: Notice of the designation of one new equivalent method for monitoring ambient air... accordance with 40 CFR part 53, one new equivalent method for measuring concentrations of lead (Pb) in total...

40 CFR 63.547 - Test methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Test methods. 63.547 Section 63.547... Hazardous Air Pollutants from Secondary Lead Smelting § 63.547 Test methods. (a) The following test methods...), and 63.545(e): (1) Method 1 shall be used to select the sampling port location and the number of...

40 CFR 63.547 - Test methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 9 2011-07-01 2011-07-01 false Test methods. 63.547 Section 63.547... Hazardous Air Pollutants from Secondary Lead Smelting § 63.547 Test methods. (a) The following test methods...), and 63.545(e): (1) Method 1 shall be used to select the sampling port location and the number of...

75 FR 30022 - Office of Research and Development; Ambient Air Monitoring Reference and Equivalent Methods...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-28

... Monitoring Reference and Equivalent Methods: Designation of One New Equivalent Method AGENCY: Environmental Protection Agency. ACTION: Notice of the designation of one new equivalent method for monitoring ambient air... accordance with 40 CFR Part 53, one new equivalent method for measuring concentrations of lead (Pb) in total...

75 FR 9894 - Office of Research and Development; Ambient Air Monitoring Reference and Equivalent Methods...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-04

... Monitoring Reference and Equivalent Methods: Designation of One New Equivalent Method AGENCY: Environmental Protection Agency. ACTION: Notice of the designation of one new equivalent method for monitoring ambient air... accordance with 40 CFR part 53, one new equivalent method for measuring concentrations of lead (Pb) in total...

An enhanced structure tensor method for sea ice ridge detection from GF-3 SAR imagery

NASA Astrophysics Data System (ADS)

Zhu, T.; Li, F.; Zhang, Y.; Zhang, S.; Spreen, G.; Dierking, W.; Heygster, G.

2017-12-01

In SAR imagery, ridges or leads are shown as the curvilinear features. The proposed ridge detection method is facilitated by their curvilinear shapes. The bright curvilinear features are recognized as the ridges while the dark curvilinear features are classified as the leads. In dual-polarization HH or HV channel of C-band SAR imagery, the bright curvilinear feature may be false alarm because the frost flowers of young leads may show as bright pixels associated with changes in the surface salinity under calm surface conditions. Wind roughened leads also trigger the backscatter increasing that can be misclassified as ridges [1]. Thus the width limitation is considered in this proposed structure tensor method [2], since only shape feature based method is not enough for detecting ridges. The ridge detection algorithm is based on the hypothesis that the bright pixels are ridges with curvilinear shapes and the ridge width is less 30 meters. Benefited from GF-3 with high spatial resolution of 3 meters, we provide an enhanced structure tensor method for detecting the significant ridge. The preprocessing procedures including the calibration and incidence angle normalization are also investigated. The bright pixels will have strong response to the bandpass filtering. The ridge training samples are delineated from the SAR imagery in the Log-Gabor filters to construct structure tensor. From the tensor, the dominant orientation of the pixel representing the ridge is determined by the dominant eigenvector. For the post-processing of structure tensor, the elongated kernel is desired to enhance the ridge curvilinear shape. Since ridge presents along a certain direction, the ratio of the dominant eigenvector will be used to measure the intensity of local anisotropy. The convolution filter has been utilized in the constructed structure tensor is used to model spatial contextual information. Ridge detection results from GF-3 show the proposed method performs better compared to the direct threshold method.

UV spectroscopy determination of aqueous lead and copper ions in water

NASA Astrophysics Data System (ADS)

Tan, C. H.; Moo, Y. C.; Mat Jafri, M. Z.; Lim, H. S.

2014-05-01

Lead (Pb2+) and copper (Cu2+) ions are very common pollutants in water which have dangerous potential causing serious disease and health problems to human. The aim of this paper is to determine lead and copper ions in aqueous solution using direct UV detection without chemical reagent waste. This technique allow the determination of lead and copper ions from range 0.2 mg/L to 10 mg/L using UV wavelength from 205 nm to 225 nm. The method was successfully applied to synthetic sample with high performance.

Lead electrowinning in a fluoborate medium. Use of hydrogen diffusion anodes

NASA Astrophysics Data System (ADS)

Expósito, E.; González-García, J.; Bonete, P.; Montiel, V.; Aldaz, A.

The results of an investigation of the electrowinning of lead employing a fluoboric acid bath are reported. The electrodeposition lead reaction was studied by voltammetric methods and scanning electron microscopy (SEM) microphotographs of the electrodeposited lead were taken. The effects of current density, temperature, catholyte flow and H + concentration were investigated on a laboratory scale to optimise operating conditions. Finally, the substitution of the traditionally used Dimensionally Stable Anode (DSA) by a Hydrogen Diffusion Electrode (HDE) was made in order to decrease the energy consumption (EC) of the overall process.

Rapid New Methods for Paint Collection and Lead Extraction

EPA Science Inventory

Chronic exposure of children to lead (Ph) can result in permanent physiologic impairment. In adults, it can cause irritability, poor muscle coordination, and nerve damage to the sense organs and nerves controlling the body. Surfaces coated with Pb-containing paints are potential ...

Field methods for determining lead content in bridge paint removal waste.

DOT National Transportation Integrated Search

2013-12-01

The removal of paint from bridges and other structures is a significant issue facing transportation agencies because of the presence and : potential for release of lead and other contaminants upon disposal. A large percentage of the bridges are reach...

METHOD OF IMPROVING THE CARRIER PRECIPITATION OF PLUTONIUM

DOEpatents

Kamack, H.J.; Balthis, J.H.

1958-12-01

Plutonium values can be recovered from acidic solutlons by adding lead nitrate, hydrogen fluoride, lantha num nitrate, and sulfurlc acid to the solution to form a carrler preclpitate. The lead sulfate formed improves the separatlon characteristics of the lanthanum fluoride carrier precipitate,

METHOD FOR JOINING ALUMINUM TO STAINLESS STEEL

DOEpatents

Lemon, L.C.

1960-05-24

Aluminum may be joined to stainless steel without the use of flux by tinning the aluminum with a tin solder containing 1% silver and 1% lead, tinning the stainless steel with a 50% lead 50% tin solder, and then sweating the tinned surfaces together.

Agile Methods in Air Force Sustainment: Status and Outlook

DTIC Science & Technology

2014-07-01

Schwaber ISBN10: 073561993X X X Agile Project Management : Creating Innovative Products – 2nd Edition Jim Highsmith ISBN 0321658396 X Agile...ISBN 0787974277 X Leading Change John Kotter ISBN 0875847471 X Leading Geeks: How to Manage and Lead the People Who Deliver Technology Paul ...Development: Achieving Enterprise Agility Alan Shalloway, Guy Beaver, and James R. Trott ISBN 0321532899 X Managing Transitions: Making the Most of

Kinetics of thermal decomposition of some biomasses in an inert environment. An investigation of the effect of lead loaded by biosorption.

PubMed

Martín-Lara, María Ángeles; Iáñez-Rodríguez, Irene; Blázquez, Gabriel; Quesada, Lucía; Pérez, Antonio; Calero, Mónica

2017-12-01

The thermal behavior of some types of raw and lead-polluted biomasses typical in south Spain was studied by non-isothermal thermogravimetry. Experiments were carried out in nitrogen atmosphere at three heating rates (5, 10 and 20°C/min). The results of thermogravimetric tests carried out proved that the presence of lead did not change the main degradation pathways of selected biomass (almond shell (AS) and olive pomace (OP)). However, from a point of view of mass loss, lead-polluted samples showed higher decomposition temperatures and decomposition at higher rate. The determination of activation energies was performed by isoconversional methods of Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS) and Friedman (FR). In general, lead-polluted samples showed lower activation energies than raw ones. Then, Coast-Redfern method was applied to determine kinetic function. The kinetic function that seems to determine the mechanism of thermal degradation of main components of all samples was nth order reaction. Finally, a model based on three parallel reactions (for three pseudocomponents) that fit to nth order reactions was evaluated. This model was appropriate to predict the pyrolysis behavior of the raw and lead-polluted samples in all pyrolysis conditions studied. Copyright © 2017 Elsevier Ltd. All rights reserved.

[Evaluation of environmental conditions: air, water and soil in areas of mining activity in Boyacá, Colombia].

PubMed

Agudelo-Calderón, Carlos A; Quiroz-Arcentales, Leonardo; García-Ubaque, Juan C; Robledo-Martínez, Rocío; García-Ubaque, Cesar A

2016-02-01

Objectives To determine concentrations of PM10, mercury and lead in indoor air of homes, water sources and soil in municipalities near mining operations. Method 6 points were evaluated in areas of influence and 2 in control areas. For measurements of indoor air, we used the NIOSH 600 method (PM10), NIOSH 6009 (mercury) and NIOSH 7300 (lead). For water analysis we used the IDEAM Guide for monitoring discharges. For soil analysis, we used the cold vapor technique (mercury) and atomic absorption (lead). Results In almost all selected households, the average PM10 and mercury concentrations in indoor air exceeded applicable air quality standards. Concentrations of lead were below standard levels. In all water sources, high concentrations of lead were found and in some places within the mining areas, high levels of iron, aluminum and mercury were also found. In soil, mercury concentrations were below the detection level and for lead, differences between the monitored points were observed. Conclusions The results do not establish causal relationships between mining and concentration of these pollutants in the evaluated areas because of the multiplicity of sources in the area. However, such studies provide important information, useful to agents of the environmental health system and researchers. Installation of networks for environmental monitoring to obtain continuous reports is suggested.

Calculating the trap density of states in organic field-effect transistors from experiment: A comparison of different methods

NASA Astrophysics Data System (ADS)

Kalb, Wolfgang L.; Batlogg, Bertram

2010-01-01

The spectral density of localized states in the band gap of pentacene (trap DOS) was determined with a pentacene-based thin-film transistor from measurements of the temperature dependence and gate-voltage dependence of the contact-corrected field-effect conductivity. Several analytical methods to calculate the trap DOS from the measured data were used to clarify, if the different methods lead to comparable results. We also used computer simulations to further test the results from the analytical methods. Most methods predict a trap DOS close to the valence-band edge that can be very well approximated by a single exponential function with a slope in the range of 50-60 meV and a trap density at the valence-band edge of ≈2×1021eV-1cm-3 . Interestingly, the trap DOS is always slightly steeper than exponential. An important finding is that the choice of the method to calculate the trap DOS from the measured data can have a considerable effect on the final result. We identify two specific simplifying assumptions that lead to significant errors in the trap DOS. The temperature dependence of the band mobility should generally not be neglected. Moreover, the assumption of a constant effective accumulation-layer thickness leads to a significant underestimation of the slope of the trap DOS.

Health-hazard evaluation report HETA 86-348-1756, J'Leen Ltd. , Boulder, Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gunter, B.J.

1986-12-01

In response to a request from the owner of J'Leen, Ltd., Boulder, Colorado, an evaluation of exposures to lead in the copper and lead glazing art studio was carried out. Breathing-zone and general air samples were analyzed by NIOSH Method P and CAM 173, blood lead was measured by voltammetry, and free-erythrocyte protoporphyrin was measured photofluorometrically. Ventilation was found to be inadequate for removing airborne lead resulting from use of lead dust and furnaces. The author concludes that the high environmental lead levels present a health hazard, and recommends improved exhaust ventilation, continued use of ultrafilter respiratory protection, and educationmore » of new employees on clean work habits.« less

NMR approaches in structure-based lead discovery: Recent developments and new frontiers for targeting multi-protein complexes

PubMed Central

Dias, David M.; Ciulli, Alessio

2014-01-01

Nuclear magnetic resonance (NMR) spectroscopy is a pivotal method for structure-based and fragment-based lead discovery because it is one of the most robust techniques to provide information on protein structure, dynamics and interaction at an atomic level in solution. Nowadays, in most ligand screening cascades, NMR-based methods are applied to identify and structurally validate small molecule binding. These can be high-throughput and are often used synergistically with other biophysical assays. Here, we describe current state-of-the-art in the portfolio of available NMR-based experiments that are used to aid early-stage lead discovery. We then focus on multi-protein complexes as targets and how NMR spectroscopy allows studying of interactions within the high molecular weight assemblies that make up a vast fraction of the yet untargeted proteome. Finally, we give our perspective on how currently available methods could build an improved strategy for drug discovery against such challenging targets. PMID:25175337

A Method for Computing the Core Flow in Three-Dimensional Leading-Edge Vortices. Ph.D. Thesis - North Carolina State Univ.

NASA Technical Reports Server (NTRS)

Luckring, J. M.

1985-01-01

A theory is presented for calculating the flow in the core of a separation-induced leading-edge vortex. The method is based on matching inner and outer representations of the vortex. The inner model of the vortex is based on the quasicylindrical Navier-Stokes equations; the flow is assumed to be steady, axially symmetric, and incompressible and in addition, gradients in the radial direction are assumed to be much larger then gradients in the axial direction. The outer model is based on the three-dimensional free-vortex-sheet theory, a higher-order panel method which solves the Prandtl-Glauert equation including nonlinear boundary conditions pertinent to the concentrated vorticity representation of the leading edge vortex. The resultant flow is evaluated a posteriori for evidence of incipient vortex breakdown and the critical helix angle concept, in conjunction with an adverse longitudinal pressure gradient, is found to correlate well with the occurrence of vortex breakdown at the trailing edge of delta, arrow, and diamond wings.

A novel method for the identification of inorganic and organic gunshot residue particles of lead-free ammunitions from the hands of shooters using scanning laser ablation-ICPMS and Raman micro-spectroscopy.

PubMed

Abrego, Zuriñe; Grijalba, Nagore; Unceta, Nora; Maguregui, Maite; Sanchez, Alicia; Fernández-Isla, Alberto; Goicolea, M Aranzazu; Barrio, Ramón J

2014-12-07

A method based on scanning laser ablation and inductively coupled plasma-mass spectrometry (SLA-ICPMS) and Raman micro-spectroscopy for the detection and identification of compounds consistent with gunshot residue particles (GSR) has been developed. The method has been applied to the characterization of particles resulting from the discharge of firearms using lead-free ammunition. Modified tape lifts were used to collect the inorganic and organic residues from skin surfaces in a single sample. Using SLA-ICPMS, aggregates related to the composition of the ammunition, such as Cu-Zn-Sn, Zr-Sr, Cu-Zn, Al-Ti, or Al-Sr-Zr were detected, but this composition is only consistent with GSR from lead-free ammunitions. Additional evidence was provided by micro-Raman spectroscopy, which identified the characteristic organic groups of the particles as centralite, diphenylamine or their nitrated derivatives, which are indicative of GSR.

Euler technology assessment for preliminary aircraft design employing OVERFLOW code with multiblock structured-grid method

NASA Technical Reports Server (NTRS)

Treiber, David A.; Muilenburg, Dennis A.

1995-01-01

The viability of applying a state-of-the-art Euler code to calculate the aerodynamic forces and moments through maximum lift coefficient for a generic sharp-edge configuration is assessed. The OVERFLOW code, a method employing overset (Chimera) grids, was used to conduct mesh refinement studies, a wind-tunnel wall sensitivity study, and a 22-run computational matrix of flow conditions, including sideslip runs and geometry variations. The subject configuration was a generic wing-body-tail geometry with chined forebody, swept wing leading-edge, and deflected part-span leading-edge flap. The analysis showed that the Euler method is adequate for capturing some of the non-linear aerodynamic effects resulting from leading-edge and forebody vortices produced at high angle-of-attack through C(sub Lmax). Computed forces and moments, as well as surface pressures, match well enough useful preliminary design information to be extracted. Vortex burst effects and vortex interactions with the configuration are also investigated.

Spatial resolution properties of motion-compensated tomographic image reconstruction methods.

PubMed

Chun, Se Young; Fessler, Jeffrey A

2012-07-01

Many motion-compensated image reconstruction (MCIR) methods have been proposed to correct for subject motion in medical imaging. MCIR methods incorporate motion models to improve image quality by reducing motion artifacts and noise. This paper analyzes the spatial resolution properties of MCIR methods and shows that nonrigid local motion can lead to nonuniform and anisotropic spatial resolution for conventional quadratic regularizers. This undesirable property is akin to the known effects of interactions between heteroscedastic log-likelihoods (e.g., Poisson likelihood) and quadratic regularizers. This effect may lead to quantification errors in small or narrow structures (such as small lesions or rings) of reconstructed images. This paper proposes novel spatial regularization design methods for three different MCIR methods that account for known nonrigid motion. We develop MCIR regularization designs that provide approximately uniform and isotropic spatial resolution and that match a user-specified target spatial resolution. Two-dimensional PET simulations demonstrate the performance and benefits of the proposed spatial regularization design methods.

Optimized mixed Markov models for motif identification

PubMed Central

Huang, Weichun; Umbach, David M; Ohler, Uwe; Li, Leping

2006-01-01

Background Identifying functional elements, such as transcriptional factor binding sites, is a fundamental step in reconstructing gene regulatory networks and remains a challenging issue, largely due to limited availability of training samples. Results We introduce a novel and flexible model, the Optimized Mixture Markov model (OMiMa), and related methods to allow adjustment of model complexity for different motifs. In comparison with other leading methods, OMiMa can incorporate more than the NNSplice's pairwise dependencies; OMiMa avoids model over-fitting better than the Permuted Variable Length Markov Model (PVLMM); and OMiMa requires smaller training samples than the Maximum Entropy Model (MEM). Testing on both simulated and actual data (regulatory cis-elements and splice sites), we found OMiMa's performance superior to the other leading methods in terms of prediction accuracy, required size of training data or computational time. Our OMiMa system, to our knowledge, is the only motif finding tool that incorporates automatic selection of the best model. OMiMa is freely available at [1]. Conclusion Our optimized mixture of Markov models represents an alternative to the existing methods for modeling dependent structures within a biological motif. Our model is conceptually simple and effective, and can improve prediction accuracy and/or computational speed over other leading methods. PMID:16749929

Lead field theory provides a powerful tool for designing microelectrode array impedance measurements for biological cell detection and observation.

PubMed

Böttrich, Marcel; Tanskanen, Jarno M A; Hyttinen, Jari A K

2017-06-26

Our aim is to introduce a method to enhance the design process of microelectrode array (MEA) based electric bioimpedance measurement systems for improved detection and viability assessment of living cells and tissues. We propose the application of electromagnetic lead field theory and reciprocity for MEA design and measurement result interpretation. Further, we simulated impedance spectroscopy (IS) with two- and four-electrode setups and a biological cell to illustrate the tool in the assessment of the capabilities of given MEA electrode constellations for detecting cells on or in the vicinity of the microelectrodes. The results show the power of the lead field theory in electromagnetic simulations of cell-microelectrode systems depicting the fundamental differences of two- and four-electrode IS measurement configurations to detect cells. Accordingly, the use in MEA system design is demonstrated by assessing the differences between the two- and four-electrode IS configurations. Further, our results show how cells affect the lead fields in these MEA system, and how we can utilize the differences of the two- and four-electrode setups in cell detection. The COMSOL simulator model is provided freely in public domain as open source. Lead field theory can be successfully applied in MEA design for the IS based assessment of biological cells providing the necessary visualization and insight for MEA design. The proposed method is expected to enhance the design and usability of automated cell and tissue manipulation systems required for bioreactors, which are intended for the automated production of cell and tissue grafts for medical purposes. MEA systems are also intended for toxicology to assess the effects of chemicals on living cells. Our results demonstrate that lead field concept is expected to enhance also the development of such methods and devices.

Dosimetric evaluation of internal shielding in a high dose rate skin applicator

PubMed Central

Granero, Domingo; Perez-Calatayud, Jose; Carmona, Vicente; Pujades, M Carmen; Ballester, Facundo

2011-01-01

Purpose The Valencia HDR applicators are accessories of the microSelectron HDR afterloading system (Nucletron) shaped as truncated cones. The base of the cone is either 2 or 3 cm diameter. They are intended to treat skin lesions, being the typical prescription depth 3 mm. In patients with eyelid lesions, an internal shielding is very useful to reduce the dose to the ocular globe. The purpose of this work was to evaluate the dose enhancement from potential backscatter and electron contamination due to the shielding. Material and methods Two methods were used: a) Monte Carlo simulation, performed with the GEANT4 code, 2 cm Valencia applicator was placed on the surface of a water phantom in which 2 mm lead slab was located at 3 mm depth; b) radiochromic EBT films, used to verify the Monte Carlo results, positioning the films at 1.5, 3, 5 and 7 mm depth, inside the phantom. Two irradiations, with and without the lead shielding slab, were carried out. Results The Monte Carlo results showed that due to the backscatter component from the lead, the dose level raised to about 200% with a depth range of 0.5 mm. Under the lead the dose level was enhanced to about 130% with a depth range of 1 mm. Two millimeters of lead reduce the dose under the slab with about 60%. These results agree with film measurements within uncertainties. Conclusions In conclusion, the use of 2 mm internal lead shielding in eyelid skin treatments with the Valencia applicators were evaluated using MC methods and EBT film dosimetry. The minimum bolus thickness that was needed above and below the shielding was 0.5 mm and 1 mm respectively, and the shielding reduced the absorbed dose delivered to the ocular globe by about 60%. PMID:27877198

40 CFR 141.89 - Analytical methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

40 CFR 141.89 - Analytical methods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 24 2013-07-01 2013-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

40 CFR 141.89 - Analytical methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 23 2014-07-01 2014-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

77 FR 7095 - Transitional Program for Covered Business Method Patents-Definition of Technological Invention

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... 0651-AC75 Transitional Program for Covered Business Method Patents-- Definition of Technological... proceeding for covered business method patents. The provision of the Leahy-Smith America Invents Act will... to the attention of ``Lead Judge Michael Tierney, Covered Business Method Patent Review Proposed...

40 CFR 141.89 - Analytical methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 23 2011-07-01 2011-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

40 CFR 141.89 - Analytical methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 24 2012-07-01 2012-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

Multiwalled carbon nanotubes as a sorbent material for the solid phase extraction of lead from urine and subsequent determination by electrothermal atomic absorption spectrometry

NASA Astrophysics Data System (ADS)

Peña Crecente, Rosa M.; Lovera, Carlha Gutiérrez; García, Julia Barciela; Méndez, Jennifer Álvarez; Martín, Sagrario García; Latorre, Carlos Herrero

2014-11-01

The determination of lead in urine is a way of monitoring the chemical exposure to this metal. In the present paper, a new method for the Pb determination by electrothermal atomic absorption spectrometry (ETAAS) in urine at low levels has been developed. Lead was separated from the undesirable urine matrix by means of a solid phase extraction (SPE) procedure. Oxidized multiwalled carbon nanotubes have been used as a sorbent material. Lead from urine was retained at pH 4.0 and was quantitatively eluted using a 0.7 M nitric acid solution and was subsequently measured by ETAAS. The effects of parameters that influence the adsorption-elution process (such as pH, eluent volume and concentration, sampling and elution flow rates) and the atomic spectrometry conditions have been studied by means of different factorial design strategies. Under the optimized conditions, the detection and quantification limits obtained were 0.08 and 0.26 μg Pb L- 1, respectively. The results demonstrate the absence of a urine matrix effect and this is the consequence of the SPE process carried out. Therefore, the developed method is useful for the analysis of Pb at low levels in real samples without the influence of other urine components. The proposed method was applied to the determination of lead in urine samples of unexposed healthy people and satisfactory results were obtained (in the range 3.64-22.9 μg Pb L- 1).

Update on Recovering Lead From Scrap Batteries

NASA Astrophysics Data System (ADS)

Cole, E. R.; Lee, A. Y.; Paulson, D. L.

1985-02-01

Previous work at the Bureau of Mines Rolla Research Center, U.S. Department of the Interior, resulted in successful development of a bench-scale, combination electrorefining-electrowinning method for recycling lead from scrap batteries by using waste fluosilicic acid (H2SiF6) as electrolyte.1,2 This paper describes larger scale experiments. Prior attempts to electrowin lead failed because large quantities of insoluble lead dioxide were deposited on the anodes at the expense of lead deposition on the cathodes. A major breakthrough was achieved with the discovery that lead dioxide formation at the anodes is prevented by adding a small amount of phosphorus to the electrolyte. The amount of PbO2 formed on the anodes during lead electrowinning was less than 1% of the total lead deposited on the cathodes. This work recently won the prestigious IR·100 award as one of the 100 most significant technological advances of 1984.

Impacts of future radiation management scenarios on terrestrial carbon dynamics simulated with fully coupled NorESM

NASA Astrophysics Data System (ADS)

Ekici, Altug; Tjiputra, Jerry; Grini, Alf; Muri, Helene

2017-04-01

We have simulated 3 different radiation management geoengineering methods (CCT - cirrus cloud thinning; SAI - stratospheric aerosol injection; MSB - marine sky brightening) on top of future RCP8.5 scenario with the fully coupled Norwegian Earth System Model (NorESM). A globally consistent cooling in both atmosphere and soil is observed with all methods. However, precipitation patterns are dependent on the used method. Globally CCT and MSB methods do not affect the vegetation carbon budget, while SAI leads to a loss compared to RCP8.5 simulations. Spatially the most sensitive region is the tropics. Here, the changes in vegetation carbon content are related to the precipitation changes. Increase in soil carbon is projected in all three methods, the biggest change seen in SAI method. Simulations with CCT method leads to twice as much soil carbon retention in the tropics compared to the MSB method. Our findings show that there are unforeseen regional consequences of such geoengineering methods in the biogeochemical cycles and they should be considered with care in future climate policies.

Development of a simple method for the determination of lead in lipstick using alkaline solubilization and graphite furnace atomic absorption spectrometry.

PubMed

Soares, Aline Rodrigues; Nascentes, Clésia Cristina

2013-02-15

A simple method was developed for determining the total lead content in lipstick samples by graphite furnace atomic absorption spectrometry (GFAAS) after treatment with tetramethylammonium hydroxide (TMAH). Multivariate optimization was used to establish the optimal conditions of sample preparation. The graphite furnace heating program was optimized through pyrolysis and atomization curves. An aliquot containing approximately 50mg of the sample was mixed with TMAH and heated in a water bath at 60°C for 60 min. Using Nb as the permanent modifier and Pd as the chemical modifier, the optimal temperatures were 900°C and 1800°C for pyrolysis and atomization, respectively. Under optimum conditions, the working range was from 1.73 to 50.0 μg L(-1), with detection and quantification limits of 0.20 and 0.34 μg g(-1), respectively. The precision was evaluated under conditions of repeatability and intermediate precision and showed standard deviations of 2.37%-4.61% and 4.93%-9.75%, respectively. The % recovery ranged from 96.2% to 109%, and no significant differences were found between the results obtained using the proposed method and the microwave decomposition method for real samples. Lead was detected in 21 tested lipstick samples; the lead content in these samples ranged from 0.27 to 4.54 μg g(-1). Copyright © 2012 Elsevier B.V. All rights reserved.

SU-E-T-802: Verification of Implanted Cardiac Pacemaker Doses in Intensity-Modulated Radiation Therapy: Dose Prediction Accuracy and Reduction Effect of a Lead Sheet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, J; Chung, J

2015-06-15

Purpose: To verify delivered doses on the implanted cardiac pacemaker, predicted doses with and without dose reduction method were verified using the MOSFET detectors in terms of beam delivery and dose calculation techniques in intensity-modulated radiation therapy (IMRT). Methods: The pacemaker doses for a patient with a tongue cancer were predicted according to the beam delivery methods [step-and-shoot (SS) and sliding window (SW)], intensity levels for dose optimization, and dose calculation algorithms. Dosimetric effects on the pacemaker were calculated three dose engines: pencil-beam convolution (PBC), analytical anisotropic algorithm (AAA), and Acuros-XB. A lead shield of 2 mm thickness was designedmore » for minimizing irradiated doses to the pacemaker. Dose variations affected by the heterogeneous material properties of the pacemaker and effectiveness of the lead shield were predicted by the Acuros-XB. Dose prediction accuracy and the feasibility of the dose reduction strategy were verified based on the measured skin doses right above the pacemaker using mosfet detectors during the radiation treatment. Results: The Acuros-XB showed underestimated skin doses and overestimated doses by the lead-shield effect, even though the lower dose disagreement was observed. It led to improved dose prediction with higher intensity level of dose optimization in IMRT. The dedicated tertiary lead sheet effectively achieved reduction of pacemaker dose up to 60%. Conclusion: The current SS technique could deliver lower scattered doses than recommendation criteria, however, use of the lead sheet contributed to reduce scattered doses.Thin lead plate can be a useful tertiary shielder and it could not acuse malfunction or electrical damage of the implanted pacemaker in IMRT. It is required to estimate more accurate scattered doses of the patient with medical device to design proper dose reduction strategy.« less

Using Wavelet Bases to Separate Scales in Quantum Field Theory

NASA Astrophysics Data System (ADS)

Michlin, Tracie L.

This thesis investigates the use of Daubechies wavelets to separate scales in local quantum field theory. Field theories have an infinite number of degrees of freedom on all distance scales. Quantum field theories are believed to describe the physics of subatomic particles. These theories have no known mathematically convergent approximation methods. Daubechies wavelet bases can be used separate degrees of freedom on different distance scales. Volume and resolution truncations lead to mathematically well-defined truncated theories that can be treated using established methods. This work demonstrates that flow equation methods can be used to block diagonalize truncated field theoretic Hamiltonians by scale. This eliminates the fine scale degrees of freedom. This may lead to approximation methods and provide an understanding of how to formulate well-defined fine resolution limits.

[Development of ICP-OES, ICP-MS and GF-AAS Methods for Simultaneous Quantification of Lead, Total Arsenic and Cadmium in Soft Drinks].

PubMed

Kataoka, Yohei; Watanabe, Takahiro; Hayashi, Tomoko; Teshima, Reiko; Matsuda, Rieko

2015-01-01

In this study, we developed methods to quantify lead, total arsenic and cadmium contained in various kinds of soft drinks, and we evaluated their performance. The samples were digested by common methods to prepare solutions for measurement by ICP-OES, ICP-MS and graphite furnace atomic absorption spectrometry (GF-AAS). After digestion, internal standard was added to the digestion solutions for measurements by ICP-OES and ICP-MS. For measurement by GF-AAS, additional purification of the digestion solution was conducted by back-extraction of the three metals into nitric acid solution after extraction into an organic solvent with ammonium pyrrolidine dithiocarbamate. Performance of the developed methods were evaluated for eight kinds of soft drinks.

Subsonic aerodynamic characteristics of interacting lifting surfaces with separated flow around sharp edges predicted by a vortex-lattice method

NASA Technical Reports Server (NTRS)

Lamar, J. E.; Gloss, B. B.

1975-01-01

Because the potential flow suction along the leading and side edges of a planform can be used to determine both leading- and side-edge vortex lift, the present investigation was undertaken to apply the vortex-lattice method to computing side-edge suction force for isolated or interacting planforms. Although there is a small effect of bound vortex sweep on the computation of the side-edge suction force, the results obtained for a number of different isolated planforms produced acceptable agreement with results obtained from a method employing continuous induced-velocity distributions. By using the method outlined, better agreement between theory and experiment was noted for a wing in the presence of a canard than was previously obtained.

[Environmental Risks to Infants and Children.

ERIC Educational Resources Information Center

Pawl, Jeree, Ed.

1991-01-01

This theme issue addresses environmental risks to infants and young children. Articles have the following titles and authors: "Lead Exposure: The Commonest Environmental Disease of Childhood" (Herbert L. Needleman); "Research in Process: A Comparison of Lead Screening Methods in Young Children" (Catherine S. Rude and David…

Characteristics of Infrared Detectors for Spece Applications

DTIC Science & Technology

2000-10-01

using Platinium Resistance Thermometers using the four lead method. The readout is performed by a high performace voltmeter, HP 3458 type. These...3.3.4 Temperature measurements The accuracy of the temperature measurements are mainly due to the Platinium Resistance Thermometers using the four lead

Curvature controlled wetting in two dimensions

NASA Astrophysics Data System (ADS)

Gil, Tamir; Mikheev, Lev V.

1995-07-01

A complete wetting transition at vanishing curvature of the substrate in two-dimensional circular geometry is studied by the transfer matrix method. We find an exact formal mapping of the partition function of the problem onto that of a (1+1)-dimensional wetting problem in planar geometry. As the radius of the substrate r0-->∞, the leading effect of the curvature is adding the Laplace pressure ΠL~r-10 to the pressure balance in the film. At temperatures and pressures under which the wetting is complete in planar geometry, Laplace pressure suppresses divergence of the mean thickness of the wetting layer lW, leading to a power law lW~r1/30. At a critical wetting transition of a planar substrate, curvature adds a relevant field; the corresponding multiscaling forms are readily available. The method allows for the systematic evaluation of corrections to the leading behavior; the next to the leading term reduces the thickness by the amount proportional to r-1/30

Toxic metals in ayurvedic preparations from a public health lead poisoning cluster investigation.

PubMed

Mikulski, Marek A; Wichman, Michael D; Simmons, Donald L; Pham, Anthony N; Clottey, Valentina; Fuortes, Laurence J

2017-07-01

Background Herbal formulations, traditional medicine, and complementary and alternative medicine are used by the majority of the world's population. Toxicity associated with use of Ayurvedic products due to metal content is an increasingly recognized potential public health problem. Objectives Report on toxic metals content of Ayurvedic products obtained during an investigation of lead poisoning among users of Ayurvedic medicine. Methods Samples of Ayurvedic formulations were analyzed for metals and metalloids following established US. Environmental Protection Agency methods. Results Lead was found in 65% of 252 Ayurvedic medicine samples with mercury and arsenic found in 38 and 32% of samples, respectively. Almost half of samples containing mercury, 36% of samples containing lead and 39% of samples containing arsenic had concentrations of those metals per pill that exceeded, up to several thousand times, the recommended daily intake values for pharmaceutical impurities. Conclusions Lack of regulations regarding manufacturing and content or purity of Ayurvedic and other herbal formulations poses a significant global public health problem.

Urban gardens: Lead exposure, recontamination mechanisms, and implications for remediation design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Clark, Heather F.; Hausladen, Debra M.; Brabander, Daniel J.

2008-07-15

Environmental lead contamination is prevalent in urban areas where soil represents a significant sink and pathway of exposure. This study characterizes the speciation of lead that is relevant to local recontamination and to human exposure in the backyard gardens of Roxbury and Dorchester, MA, USA. One hundred forty-one backyard gardens were tested by X-ray fluorescence, and 81% of gardens have lead levels above the US EPA action limit of 400 {mu}g/g. Raised gardening beds are the in situ exposure reduction method used in the communities to promote urban gardening. Raised beds were tested for lead and the results showed thatmore » the lead concentration increased from an initial range of 150{+-}40 {mu}g/g to an average of 336 {mu}g/g over 4 years. The percent distribution of lead in the fine grain soil (<100 {mu}m) and the trace metal signature of the raised beds support the conclusion that the mechanism of recontamination is wind-transported particles. Scanning electron microscopy and sequential extraction were used to characterize the speciation of lead, and the trace metal signature of the fine grain soil in both gardens and raised gardening beds is characteristic of lead-based paint. This study demonstrates that raised beds are a limited exposure reduction method and require maintenance to achieve exposure reduction goals. An exposure model was developed based on a suite of parameters that combine relevant values from the literature with site-specific quantification of exposure pathways. This model suggests that consumption of homegrown produce accounts for only 3% of children's daily exposure of lead while ingestion of fine grained soil (<100 {mu}m) accounts for 82% of the daily exposure. This study indicates that urban lead remediation on a yard-by-yard scale requires constant maintenance and that remediation may need to occur on a neighborhood-wide scale.« less

Urban gardens: lead exposure, recontamination mechanisms, and implications for remediation design.

PubMed

Clark, Heather F; Hausladen, Debra M; Brabander, Daniel J

2008-07-01

Environmental lead contamination is prevalent in urban areas where soil represents a significant sink and pathway of exposure. This study characterizes the speciation of lead that is relevant to local recontamination and to human exposure in the backyard gardens of Roxbury and Dorchester, MA, USA. One hundred forty-one backyard gardens were tested by X-ray fluorescence, and 81% of gardens have lead levels above the US EPA action limit of 400 microg/g. Raised gardening beds are the in situ exposure reduction method used in the communities to promote urban gardening. Raised beds were tested for lead and the results showed that the lead concentration increased from an initial range of 150+/-40 microg/g to an average of 336 microg/g over 4 years. The percent distribution of lead in the fine grain soil (<100 microm) and the trace metal signature of the raised beds support the conclusion that the mechanism of recontamination is wind-transported particles. Scanning electron microscopy and sequential extraction were used to characterize the speciation of lead, and the trace metal signature of the fine grain soil in both gardens and raised gardening beds is characteristic of lead-based paint. This study demonstrates that raised beds are a limited exposure reduction method and require maintenance to achieve exposure reduction goals. An exposure model was developed based on a suite of parameters that combine relevant values from the literature with site-specific quantification of exposure pathways. This model suggests that consumption of homegrown produce accounts for only 3% of children's daily exposure of lead while ingestion of fine grained soil (<100 microm) accounts for 82% of the daily exposure. This study indicates that urban lead remediation on a yard-by-yard scale requires constant maintenance and that remediation may need to occur on a neighborhood-wide scale.

Assessment of the post-implant final left ventricular lead position: a comparative study between radiographic and angiographic modalities.

PubMed

Kumar, Prabhat; Blendea, Dan; Nandigam, Veena; Moore, Stephanie A; Heist, E Kevin; Singh, Jagmeet P

2010-10-01

Post-implant lateral and postero-anterior chest X-rays (CXR) are often utilized to determine the final LV lead tip position after cardiac resynchronization therapy (CRT). This study sought to compare post-implant standard CXRs with intra-procedural rotational coronary venous angiography (RCVA) to localize the final LV lead position. Sixty-four patients undergoing CRT (69.2 ± 11.4 years; males 68.7%; ischemic cardiomyopathy 59.4%; NYHA class 2.9 ± 0.5 and LV ejection fraction 24% ± 9%) were included in the study. RCVA was done by recording a rapid 4-second isocentric cine-loop from RAO 55° to LAO 55° (120 frames). Conventional CXR method (CC) and a composite CXR strategy (CM) based on two-view CXR were separately compared with RCVA. The most common pacing site was lateral (64.1%), followed by postero-lateral (23.4%) and antero-lateral (10.9%). In 73.4% (47) cases, the LV lead position was misclassified by CC as compared to RCVA. Among the 47 (73.4%) cases misclassified by CC approach, 35 had lateral LV lead position misclassified by CC as postero-lateral (77%), posterior (20%) and antero-lateral (3%). On the other hand, CM strategy classified the LV lead position correctly in 46 (71.9%) of the patients (p < 0.0001). The composite CXR strategy is a useful method for post-procedure LV lead localization. Due to its simplicity, it can be widely applied in post-implant evaluation of LV lead position in CRT patients.

Selecting, training and assessing new general practice community teachers in UK medical schools.

PubMed

Hydes, Ciaran; Ajjawi, Rola

2015-09-01

Standards for undergraduate medical education in the UK, published in Tomorrow's Doctors, include the criterion 'everyone involved in educating medical students will be appropriately selected, trained, supported and appraised'. To establish how new general practice (GP) community teachers of medical students are selected, initially trained and assessed by UK medical schools and establish the extent to which Tomorrow's Doctors standards are being met. A mixed-methods study with questionnaire data collected from 24 lead GPs at UK medical schools, 23 new GP teachers from two medical schools plus a semi-structured telephone interview with two GP leads. Quantitative data were analysed descriptively and qualitative data were analysed informed by framework analysis. GP teachers' selection is non-standardised. One hundred per cent of GP leads provide initial training courses for new GP teachers; 50% are mandatory. The content and length of courses varies. All GP leads use student feedback to assess teaching, but other required methods (peer review and patient feedback) are not universally used. To meet General Medical Council standards, medical schools need to include equality and diversity in initial training and use more than one method to assess new GP teachers. Wider debate about the selection, training and assessment of new GP teachers is needed to agree minimum standards.

The use of contraception for patients after bariatric surgery.

PubMed

Ostrowska, Lucyna; Lech, Medard; Stefańska, Ewa; Jastrzębska-Mierzyńska, Marta; Smarkusz, Joanna

2016-01-01

Obesity in women of reproductive age is a serious concern regarding reproductive health. In many cases of infertility in obese women, reduction of body weight may lead to spontaneous pregnancy, without the need for more specific methods of treatment. Bariatric surgery is safe and is the most effective method for body weight reduction in obese and very obese patients. In practice there are two bariatric techniques; gastric banding, which leads to weight loss through intake restriction, and gastric bypass, leads to weight loss through food malabsorption. Gastric bypass surgery (the more frequently performed procedure), in most cases, leads to changes in eating habits and may result in vomiting, diarrhea and rapid body mass reduction. There are reliable data describing the continuous increase in the number of women who are trying to conceive, or are already pregnant, following bariatric surgery. Most medical specialists advise women to avoid pregnancy within 12-18 months after bariatric surgery. This allows for time to recover sufficiency from the decreased absorption of nutrients caused by the bariatric surgery. During this period there is a need for the use of reliable contraception. As there is a risk for malabsorption of hormones taken orally, the combined and progestogen-only pills are contraindicated, and displaced by non-oral hormonal contraception or non-hormonal methods, including intrauterine devices and condoms.

RADIAL FLOW PATTERN OF A SLOW CORONAL MASS EJECTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Li; Gan, Weiqun, E-mail: lfeng@pmo.ac.cn; Inhester, Bernd

2015-06-01

Height–time plots of the leading edge of coronal mass ejections (CMEs) have often been used to study CME kinematics. We propose a new method to analyze the CME kinematics in more detail by determining the radial mass transport process throughout the entire CME. Thus, our method is able to estimate not only the speed of the CME front but also the radial flow speed inside the CME. We have applied this method to a slow CME with an average leading edge speed of about 480 km s{sup −1}. In the Lagrangian frame, the speeds of the individual CME mass elementsmore » stay almost constant within 2 and 15 R{sub S}, the range over which we analyzed the CME. Hence, we have no evidence of net radial forces acting on parts of the CME in this range or of a pile up of mass ahead of the CME. We find evidence that the leading edge trajectory obtained by tie-pointing may gradually lag behind the Lagrangian front-side trajectories derived from our analysis. Our results also allow a much more precise estimate of the CME energy. Compared with conventional estimates using the CME total mass and leading edge motion, we find that the latter may overestimate the kinetic energy and the gravitational potential energy.« less

Numerical integration of discontinuous functions: moment fitting and smart octree

NASA Astrophysics Data System (ADS)

Hubrich, Simeon; Di Stolfo, Paolo; Kudela, László; Kollmannsberger, Stefan; Rank, Ernst; Schröder, Andreas; Düster, Alexander

2017-11-01

A fast and simple grid generation can be achieved by non-standard discretization methods where the mesh does not conform to the boundary or the internal interfaces of the problem. However, this simplification leads to discontinuous integrands for intersected elements and, therefore, standard quadrature rules do not perform well anymore. Consequently, special methods are required for the numerical integration. To this end, we present two approaches to obtain quadrature rules for arbitrary domains. The first approach is based on an extension of the moment fitting method combined with an optimization strategy for the position and weights of the quadrature points. In the second approach, we apply the smart octree, which generates curved sub-cells for the integration mesh. To demonstrate the performance of the proposed methods, we consider several numerical examples, showing that the methods lead to efficient quadrature rules, resulting in less integration points and in high accuracy.

Methods for separating particles and/or nucleic acids using isotachophoresis

DOEpatents

Jung, Byoungsok; Ness, Kevin; Rose, Klint A.

2016-03-15

According to one embodiment, a method includes co-feeding fluids comprising a leading electrolyte, a trailing electrolyte, and at least one of DNA and RNA to a channel, and applying an electric field to the fluids in a direction perpendicular to an axis of the channel for inducing transverse isotachophoresis. In another embodiment, a method includes co-feeding fluids to a channel. The fluids include a leading electrolyte, a trailing electrolyte, biological objects, at least one of DNA and RNA, and a spacer electrolyte having an electrophoretic mobility that is between an electrophoretic mobility of at least some of the biological objects and an electrophoretic mobility of the at least one of the DNA and the RNA. The method also includes applying an electric field to the fluids in a direction perpendicular to an axis of the channel for inducing transverse isotachophoresis. Other methods of isotachophoresis are disclosed in addition to these.

Community- and family-level factors influence care-giver choice to screen blood lead levels of children in a mining community.

PubMed

Moodie, S M; Tsui, E K; Silbergeld, E K

2010-07-01

Bunker Hill, in Kellogg, Idaho, formerly a lead mine (1884-1981) and smelter (1917-1981), is now a Superfund site listed on the Environmental Protection Agency's (EPA) National Priorities List. Lead contamination from the site is widespread due to past smelter discharges to land, water, and air, placing children at risk for both exposure to lead and resultant health effects of lead. Since 1983, the EPA has used child blood lead levels to inform the clean-up standards for the Bunker Hill Superfund site. This study was undertaken to examine factors that have contributed to the significant fall-off in the rates and numbers of children being screened for blood lead in Kellogg (number screened decreased from 195 to 8 from 2002 to 2007). The goal of this research project was to define community- and family-level factors which influence care-giver choice to screen blood lead levels of their children in this environment. This formative research study used mixed methods and was comprised of three research components: (1) preliminary interviews using community-based participatory research methods to define key research questions of relevance to community members, government and NGOs working in relation to the Bunker Hill clean-up; (2) a quantitative analysis of a cross-sectional household survey conducted with adult care-givers about child blood lead screening in Kellogg; and (3) ethnographic community rapid assessment methods formed the in-depth interview process and qualitative analysis. The survey showed the likelihood of blood lead screening that for children under the age of 18 years increases 34% with each one-year increase in current age of the child (95% CI, 1.08-1.67, p-value=0.009), and decreases 45% with annual household income greater than $10,000 (95% CI, 0.35-0.88, p-value=0.013). Sibling birth order increased the likelihood of blood lead screening by 61% (95% CI, 1.04-2.48, p-value=0.032) for each successive child. Female children were rated by their care-givers as 3.7 times less agitated or easily angered than male children (95% CI, 1.5-8.8, p-value=0.005). Across all levels of interviews, regulators, residents, and non-governmental organization representatives reported that Kellogg's long history as a mining town has continued to influence attitudes and actions of care-givers to access blood lead screening for their children. The mining context has been described as instilling stigmas, parental blame and a sense of shame about lead exposure and resultant health effects. Children under 6 years of age are currently the least likely to have been screened for lead in Kellogg and screening rates decreased in the 2000s. According to most indicators, socio-economic status did not influence the likelihood of a care-giver to screen children's blood lead levels. However, children in homes with an annual income below $10,000 were more likely to have been screened than the rest of the population. Former concerted screening efforts, including outreach, support, follow-up, and financial incentives in the 1980s-1990s to screen children, may have influenced low-income residents. Programmatic outreach for children under 6 years of age in Kellogg should focus on increasing female child and first child blood lead screening, rather than targeting only low-income families, by improving approaches to promotion, implementation and environmental follow-up for child lead screening. Some families have resided in Kellogg for five to six generations, and the long-term mining context influences community values and perceptions of lead exposure and screening for children through a conflicted combination of pride in the mining history, attachment to the past economy that supported the community in juxtaposition to the personalized blame, shame, guilt, and stigma associated with children having high blood lead levels. Health communication and other programs should prioritize methods of reducing parental feelings of blame, shame and guilt, and stigmas associated with the health effects of lead in a way that respects the pride of former mine workers, their families, and the history of the town. 2010 Elsevier Inc. All rights reserved.

W -Boson Production in Association with a Jet at Next-to-Next-to-Leading Order in Perturbative QCD

NASA Astrophysics Data System (ADS)

Boughezal, Radja; Focke, Christfried; Liu, Xiaohui; Petriello, Frank

2015-08-01

We present the complete calculation of W -boson production in association with a jet in hadronic collisions through next-to-next-to-leading order (NNLO) in perturbative QCD. To cancel infrared divergences, we discuss a new subtraction method that exploits the fact that the N -jettiness event-shape variable fully captures the singularity structure of QCD amplitudes with final-state partons. This method holds for processes with an arbitrary number of jets and is easily implemented into existing frameworks for higher-order calculations. We present initial phenomenological results for W +jet production at the LHC. The NNLO corrections are small and lead to a significantly reduced theoretical error, opening the door to precision measurements in the W +jet channel at the LHC.

Large piezoelectric properties in KNN-based lead-free single crystals grown by a seed-free solid-state crystal growth method

NASA Astrophysics Data System (ADS)

Yang, Jie; Zhang, Faqiang; Yang, Qunbao; Liu, Zhifu; Li, Yongxiang; Liu, Yun; Zhang, Qiming

2016-05-01

We report lead-free single crystals with a nominal formula of (K0.45Na0.55)0.96Li0.04NbO3 grown using a simple low-cost seed-free solid-state crystal growth method (SFSSCG). The crystals thus prepared can reach maximum dimensions of 6 mm × 5 mm × 2 mm and exhibit a large piezoelectric coefficient d33 of 689 pC/N. Moreover, the effective piezoelectric coefficient d33 * , obtained under a unipolar electric field of 30 kV/cm, can reach 967 pm/V. The large piezoelectric response plus the high Curie temperature (TC) of 432 °C indicate that SFSSCG is an effective approach to synthesize high-performance lead-free piezoelectric single crystals.

Nuclear qualified in-containment electrical connectors and method of connecting electrical conductors

DOEpatents

Powell, J. G.

1991-01-01

A nuclear qualified in-containment electrical connection comprises an insulated, sheathed instrument lead having electrical conductors extending from one end thereof to provide two exposed lead wires, a watertight cable having electrical conducting wires therein and extending from one end of the cable to provide two lead wires therefrom, two butt splice connectors each connecting the ends of respective ones of the lead wires from the instrument lead and cable, a length of heat shrinkable plastic tubing positioned over each butt splice connector and an adjacent portion of a respective lead wire from the cable and heat shrunk into position, a length of heat shrinkable plastic tubing on the end portion of the instrument lead adjacent the lead wires therefrom and heat shrunk thereon and a length of outer heat shrinkable plastic tubing extending over the end portion of the instrument lead and the heat shrinkable tubing thereon and over the butt splice connectors and a portion of the cable adjacent the cable lead lines, the outer heat shrinkable tubing being heat shrunk into sealing position on the instrument lead and cable.

A New Pulse Pileup Rejection Method Based on Position Shift Identification

NASA Astrophysics Data System (ADS)

Gu, Z.; Prout, D. L.; Taschereau, R.; Bai, B.; Chatziioannou, A. F.

2016-02-01

Pulse pileup events degrade the signal-to-noise ratio (SNR) of nuclear medicine data. When such events occur in multiplexed detectors, they cause spatial misposition, energy spectrum distortion and degraded timing resolution, which leads to image artifacts. Pulse pileup is pronounced in PETbox4, a bench top PET scanner dedicated to high sensitivity and high resolution imaging of mice. In that system, the combination of high absolute sensitivity, long scintillator decay time (BGO) and highly multiplexed electronics lead to a significant fraction of pulse pileup, reached at lower total activity than for comparable instruments. In this manuscript, a new pulse pileup rejection method named position shift rejection (PSR) is introduced. The performance of PSR is compared with a conventional leading edge rejection (LER) method and with no pileup rejection implemented (NoPR). A comprehensive digital pulse library was developed for objective evaluation and optimization of the PSR and LER, in which pulse waveforms were directly recorded from real measurements exactly representing the signals to be processed. Physical measurements including singles event acquisition, peak system sensitivity and NEMA NU-4 image quality phantom were also performed in the PETbox4 system to validate and compare the different pulse pile-up rejection methods. The evaluation of both physical measurements and model pulse trains demonstrated that the new PSR performs more accurate pileup event identification and avoids erroneous rejection of valid events. For the PETbox4 system, this improvement leads to a significant recovery of sensitivity at low count rates, amounting to about 1/4th of the expected true coincidence events, compared to the LER method. Furthermore, with the implementation of PSR, optimal image quality can be achieved near the peak noise equivalent count rate (NECR).

The roles of the Q (q) wave in lead I and QRS frontal axis for diagnosing loss of left ventricular capture during cardiac resynchronization therapy.

PubMed

Cao, Yuan-Yuan; Su, Yan-Gang; Bai, Jin; Wang, Wei; Wang, Jing-Feng; Qin, Sheng-Mei; Ge, Jun-Bo

2015-01-01

Loss of left ventricular (LV) capture may lead to deterioration of heart failure in patients with cardiac resynchronization therapy (CRT). Recognition of loss of LV capture in time is important in clinical practice. A total of 422 electrocardiograms were acquired and analyzed from 53 CRT patients at 8 different pacing settings (LV only, right ventricle [RV] only, biventricular [BV] pacing with LV preactivation of 60, 40, 20, and 0 milliseconds and RV preactivation of 20 and 40 milliseconds). A modified Ammann algorithm by adding a third step-presence of Q (q, or QS) wave-to the original 2-step Ammann algorithm and a QRS axis shift method were devised to identify the loss of LV capture. The accuracy of modified Ammann algorithm was significantly higher than that of Ammann algorithm (78.9% vs. 69.1%, P < 0.001). The accuracy of the axis shift method was 66.4%, which was significantly lower than the modified Ammann algorithm (P < 0.001) and similar to the original one (P = 0.412). However, in the ECGs with QRS axis shift, 96.8% were correctly classified. LV preactivation or simultaneous BV activation and LV lead positioned in nonposterior or noninferior wall could elevate the accuracies of the modified Ammann algorithm and the QRS axis shift method. The accuracy of the modified Ammann algorithm is greatly improved. The QRS axis shift method can help diagnose LV capture. The LV preactivation, or simultaneous BV activation and LV lead positioned in nonposterior or noninferior wall can increase the diagnostic power of the modified Ammann algorithm and QRS axis shift method. © 2014 Wiley Periodicals, Inc.

Accuracy of effective dose estimation in personal dosimetry: a comparison between single-badge and double-badge methods and the MOSFET method.

PubMed

Januzis, Natalie; Belley, Matthew D; Nguyen, Giao; Toncheva, Greta; Lowry, Carolyn; Miller, Michael J; Smith, Tony P; Yoshizumi, Terry T

2014-05-01

The purpose of this study was three-fold: (1) to measure the transmission properties of various lead shielding materials, (2) to benchmark the accuracy of commercial film badge readings, and (3) to compare the accuracy of effective dose (ED) conversion factors (CF) of the U.S. Nuclear Regulatory Commission methods to the MOSFET method. The transmission properties of lead aprons and the accuracy of film badges were studied using an ion chamber and monitor. ED was determined using an adult male anthropomorphic phantom that was loaded with 20 diagnostic MOSFET detectors and scanned with a whole body CT protocol at 80, 100, and 120 kVp. One commercial film badge was placed at the collar and one at the waist. Individual organ doses and waist badge readings were corrected for lead apron attenuation. ED was computed using ICRP 103 tissue weighting factors, and ED CFs were calculated by taking the ratio of ED and badge reading. The measured single badge CFs were 0.01 (±14.9%), 0.02 (±9.49%), and 0.04 (±15.7%) for 80, 100, and 120 kVp, respectively. Current regulatory ED CF for the single badge method is 0.3; for the double-badge system, they are 0.04 (collar) and 1.5 (under lead apron at the waist). The double-badge system provides a better coefficient for the collar at 0.04; however, exposure readings under the apron are usually negligible to zero. Based on these findings, the authors recommend the use of ED CF of 0.01 for the single badge system from 80 kVp (effective energy 50.4 keV) data.

Intracardiac electrocardiography via a "saline-filled central venous catheter electrocardiographic lead": a historical perspective.

PubMed

Madias, John E

2004-04-01

The author describes his experience with a "saline-filled central venous catheter electrocardiographic lead" for the recording of intracardiac electrocardiograms provides a brief description of the methodology, refers to this modality's clinical usefulness, furnishes 2 examples illustrating the contribution of the method to clinical diagnosis, and outlines his literature search to find the discoverer/originator of the employment of a saline-filled intracardiac catheter as an electrocardiogram recording lead.

Wind Plant Performance Prediction (WP3) Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Craig, Anna

The methods for analysis of operational wind plant data are highly variable across the wind industry, leading to high uncertainties in the validation and bias-correction of preconstruction energy estimation methods. Lack of credibility in the preconstruction energy estimates leads to significant impacts on project financing and therefore the final levelized cost of energy for the plant. In this work, the variation in the evaluation of a wind plant's operational energy production as a result of variations in the processing methods applied to the operational data is examined. Preliminary results indicate that selection of the filters applied to the data andmore » the filter parameters can have significant impacts in the final computed assessment metrics.« less

NUCLEON-mission: A New Approach to Cosmic Rays Investigation

NASA Technical Reports Server (NTRS)

Adams, J.; Bashindzhagyan, G.; Chilingarian, A.; Drury, L.; Egorov, N.; Golubkov, S.; Grebenyuk, V.; Korotkova, N.; Mashkantcev, A.; Nanjo, H.;

Longitudinal changes in bone lead levels: the VA Normative Aging Study

PubMed Central

Wilker, Elissa; Korrick, Susan; Nie, Linda H; Sparrow, David; Vokonas, Pantel; Coull, Brent; Wright, Robert O.; Schwartz, Joel; Hu, Howard

2011-01-01

Objective Bone lead is a cumulative measure of lead exposure that can also be remobilized. We examined repeated measures of bone lead over 11 years to characterize long-term changes and identify predictors of tibia and patella lead stores in an elderly male population. Methods Lead was measured every 3–5 years by k-x-ray fluorescence and mixed-effect models with random effects were used to evaluate change over time. Results 554 participants provided up to 4 bone lead measurements. Final models predicted a −1.4% annual decline (95%CI: −2.2,−0.7) for tibia lead and piecewise linear model for patella with an initial decline of 5.1% per year (95%CI: −6.2,−3.9) during the first 4.6 years but no significant change thereafter (−0.4% (95% CI: −2.4, 1.7)). Conclusions These results suggest that bone lead half-life may be longer than previously reported. PMID:21788910

[Application of the data from China Total Diet Study to assess the distribution of lead exposure in different age-gender population groups].

PubMed

Li, Xiaowei; Liu, Qing; Liu, Liping; Wu, Yongning

2012-05-01

To assess the distribution of dietary lead exposure in different age-gender groups of Chinese residents by using the data from China Total Diet Study, and combining the new risk assessment and the PTWI withdrawn by JECFA. Methods Combining the lead concentrations of dietary samples with the food consumption data from China Total Diet Study in 2007 to obtain the distribution of dietary intake and dietary source of lead in different age-gender population groups. Dietary lead exposure of different age-gender population groups in China was in the range of 48.7 -116.7 microg/d. The status of higher lead exposure in younger age groups was not optimistic, as the mean and median margins of exposure (MOE) have been less than 1.0 (0.1 - 0.3). The main sources of dietary lead were cereals and vegetables, which covering 57% of total lead exposure. Lowering the dietary lead exposure of Chinese residents is necessary, especially of infants and children.

Heavy metal speciation and uptake in crayfish and tadpoles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bundy, K.J.; Berzins, D.; Millet, L.

1996-12-31

Developing valid pollution recording methods is central to assessing environmental damage and remediation. This often is difficult, however, because of speciation and multiphase distribution of contaminants. Polarography, an electroanalytical technique capable of detection and quantification of trace levels of elements and ionic complexes, is a promising method for analyzing environmental samples. Here, polarography has been used to determine lead concentration in water, sediment, bullfrogs, tadpoles, and adsorbed onto kaolin. It has also been used to measure hexavalent chromium concentration in crayfish. This research involves field studies and two laboratory experiments. Studies of a Louisiana swamp have shown lead`s affinity formore » sediment and water particulate phases, rather than being ionically dissolved in the aqueous phase. In swamp bullfrogs, lead was found in greater concentrations in bone compared to muscle. In the first laboratory experiment, lead uptake originating from water and sediment increased in tadpoles as exposure time and concentration increased. Also, this animal`s development was hindered at higher concentrations. The second laboratory experiment exposed crayfish to aqueous hexavalent chromium. Total chromium uptake increased with exposure time and concentration. The chromium tissue abundance was hepatopancreas > gills > muscle. A substantial portion of tissue hexavalent chromium converted to the less toxic trivalent form.« less

A Novel Face-on-Face Contact Method for Nonlinear Solid Mechanics

NASA Astrophysics Data System (ADS)

Wopschall, Steven Robert

The implicit solution to contact problems in nonlinear solid mechanics poses many difficulties. Traditional node-to-segment methods may suffer from locking and experience contact force chatter in the presence of sliding. More recent developments include mortar based methods, which resolve local contact interactions over face-pairs and feature a kinematic constraint in integral form that smoothes contact behavior, especially in the presence of sliding. These methods have been shown to perform well in the presence of geometric nonlinearities and are demonstratively more robust than node-to-segment methods. These methods are typically biased, however, interpolating contact tractions and gap equations on a designated non-mortar face, which leads to an asymmetry in the formulation. Another challenge is constraint enforcement. The general selection of the active set of constraints is brought with difficulty, often leading to non-physical solutions and easily resulting in missed face-pair interactions. Details on reliable constraint enforcement methods are lacking in the greater contact literature. This work presents an unbiased contact formulation utilizing a median-plane methodology. Up to linear polynomials are used for the discrete pressure representation and integral gap constraints are enforced using a novel subcycling procedure. This procedure reliably determines the active set of contact constraints leading to physical and kinematically admissible solutions void of heuristics and user action. The contact method presented herein successfully solves difficult quasi-static contact problems in the implicit computational setting. These problems feature finite deformations, material nonlinearity, and complex interface geometries, all of which are challenging characteristics for contact implementations and constraint enforcement algorithms. The subcycling procedure is a key feature of this method, handling active constraint selection for complex interfaces and mesh geometries.

Root removal to improve disease management in replanted Washington red raspberry fields

USDA-ARS?s Scientific Manuscript database

Washington leads the nation in the production of red raspberries for processing. Soilborne pathogens are a production constraint in this $61 million industry with growers relying on preplant soil fumigation for their management. However, current fumigation methods can be ineffective, leading to repl...

Lead Pipe Scale Analysis Using Broad-Beam Argon Ion Milling to Elucidate Drinking Water Corrosion

EPA Science Inventory

Herein, we compared the characterization of lead pipe scale removed from a drinking water distribution system using two different cross section methods (conventional polishing and argon ion beam etching). The pipe scale solids were analyzed using scanning electron microscopy (SEM...

Leads Detection Using Mixture Statistical Distribution Based CRF Algorithm from Sentinel-1 Dual Polarization SAR Imagery

NASA Astrophysics Data System (ADS)

Zhang, Yu; Li, Fei; Zhang, Shengkai; Zhu, Tingting

2017-04-01

Synthetic Aperture Radar (SAR) is significantly important for polar remote sensing since it can provide continuous observations in all days and all weather. SAR can be used for extracting the surface roughness information characterized by the variance of dielectric properties and different polarization channels, which make it possible to observe different ice types and surface structure for deformation analysis. In November, 2016, Chinese National Antarctic Research Expedition (CHINARE) 33rd cruise has set sails in sea ice zone in Antarctic. Accurate leads spatial distribution in sea ice zone for routine planning of ship navigation is essential. In this study, the semantic relationship between leads and sea ice categories has been described by the Conditional Random Fields (CRF) model, and leads characteristics have been modeled by statistical distributions in SAR imagery. In the proposed algorithm, a mixture statistical distribution based CRF is developed by considering the contexture information and the statistical characteristics of sea ice for improving leads detection in Sentinel-1A dual polarization SAR imagery. The unary potential and pairwise potential in CRF model is constructed by integrating the posteriori probability estimated from statistical distributions. For mixture statistical distribution parameter estimation, Method of Logarithmic Cumulants (MoLC) is exploited for single statistical distribution parameters estimation. The iteration based Expectation Maximal (EM) algorithm is investigated to calculate the parameters in mixture statistical distribution based CRF model. In the posteriori probability inference, graph-cut energy minimization method is adopted in the initial leads detection. The post-processing procedures including aspect ratio constrain and spatial smoothing approaches are utilized to improve the visual result. The proposed method is validated on Sentinel-1A SAR C-band Extra Wide Swath (EW) Ground Range Detected (GRD) imagery with a pixel spacing of 40 meters near Prydz Bay area, East Antarctica. Main work is listed as follows: 1) A mixture statistical distribution based CRF algorithm has been developed for leads detection from Sentinel-1A dual polarization images. 2) The assessment of the proposed mixture statistical distribution based CRF method and single distribution based CRF algorithm has been presented. 3) The preferable parameters sets including statistical distributions, the aspect ratio threshold and spatial smoothing window size have been provided. In the future, the proposed algorithm will be developed for the operational Sentinel series data sets processing due to its less time consuming cost and high accuracy in leads detection.

40 CFR 80.3 - Test methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 17 2012-07-01 2012-07-01 false Test methods. 80.3 Section 80.3... FUELS AND FUEL ADDITIVES General Provisions § 80.3 Test methods. The lead and phosphorus content of gasoline shall be determined in accordance with test methods set forth in the appendices to this part. [47...

40 CFR 63.1546 - Test methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Test methods. 63.1546 Section 63.1546... Hazardous Air Pollutants for Primary Lead Smelting § 63.1546 Test methods. (a) The following procedure shall....1543(a)(1) through § 63.1543(a)(9) shall be determined according to the following test methods in...

40 CFR 63.547 - Test methods.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 10 2012-07-01 2012-07-01 false Test methods. 63.547 Section 63.547... Hazardous Air Pollutants From Secondary Lead Smelting § 63.547 Test methods. (a) You must use the test methods from appendix A of part 60 as listed in paragraphs (a)(1) through (5) of this section to determine...

40 CFR 63.547 - Test methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 10 2014-07-01 2014-07-01 false Test methods. 63.547 Section 63.547... Hazardous Air Pollutants From Secondary Lead Smelting § 63.547 Test methods. (a) You must use the test methods from appendix A of part 60 as listed in paragraphs (a)(1) through (5) of this section to determine...

40 CFR 80.3 - Test methods.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 17 2014-07-01 2014-07-01 false Test methods. 80.3 Section 80.3... FUELS AND FUEL ADDITIVES General Provisions § 80.3 Test methods. The lead and phosphorus content of gasoline shall be determined in accordance with test methods set forth in the appendices to this part. [47...

40 CFR 63.1546 - Test methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Test methods. 63.1546 Section 63.1546... Hazardous Air Pollutants for Primary Lead Smelting § 63.1546 Test methods. (a) The following procedure shall....1543(a)(1) through § 63.1543(a)(9) shall be determined according to the following test methods in...

40 CFR 80.3 - Test methods.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Test methods. 80.3 Section 80.3... FUELS AND FUEL ADDITIVES General Provisions § 80.3 Test methods. The lead and phosphorus content of gasoline shall be determined in accordance with test methods set forth in the appendices to this part. [47...

40 CFR 80.3 - Test methods.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 16 2011-07-01 2011-07-01 false Test methods. 80.3 Section 80.3... FUELS AND FUEL ADDITIVES General Provisions § 80.3 Test methods. The lead and phosphorus content of gasoline shall be determined in accordance with test methods set forth in the appendices to this part. [47...

40 CFR 63.547 - Test methods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 10 2013-07-01 2013-07-01 false Test methods. 63.547 Section 63.547... Hazardous Air Pollutants From Secondary Lead Smelting § 63.547 Test methods. (a) You must use the test methods from appendix A of part 60 as listed in paragraphs (a)(1) through (5) of this section to determine...

40 CFR 80.3 - Test methods.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 17 2013-07-01 2013-07-01 false Test methods. 80.3 Section 80.3... FUELS AND FUEL ADDITIVES General Provisions § 80.3 Test methods. The lead and phosphorus content of gasoline shall be determined in accordance with test methods set forth in the appendices to this part. [47...

78 FR 40000 - Method for the Determination of Lead in Total Suspended Particulate Matter

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-03

.... Purpose of the New Reference Method B. Rationale for Selection of the New Reference Method C. Comments on.../files/ambient/criteria/reference-equivalent-methods-list.pdf . C. Comments on the Proposed Rule On... information collection requirements beyond those imposed by the existing Pb monitoring requirements. C...

77 FR 32632 - Ambient Air Monitoring Reference and Equivalent Methods: Designation of Three New Equivalent Methods

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

... Hydrogen Peroxide Filter Extraction'' In this method, total suspended particulate matter (TSP) is collected on glass fiber filters according to 40 CFR Appendix G to part 50, EPA Reference Method for the Determination of Lead in Suspended Particulate Matter Collected From Ambient Air. The filter samples are...

An Alternative Method to the Classical Partial Fraction Decomposition

ERIC Educational Resources Information Center

Cherif, Chokri

2007-01-01

PreCalculus students can use the Completing the Square Method to solve quadratic equations without the need to memorize the quadratic formula since this method naturally leads them to that formula. Calculus students, when studying integration, use various standard methods to compute integrals depending on the type of function to be integrated.…

An improved panel method for the solution of three-dimensional leading-edge vortex flows. Volume 1: Theory document

NASA Technical Reports Server (NTRS)

Johnson, F. T.; Lu, P.; Tinoco, E. N.

1980-01-01

An improved panel method for the solution of three dimensional flow and wing and wing-body combinations with leading edge vortex separation is presented. The method employs a three dimensional inviscid flow model in which the configuration, the rolled-up vortex sheets, and the wake are represented by quadratic doublet distributions. The strength of the singularity distribution as well as shape and position of the vortex spirals are computed in an iterative fashion starting with an assumed initial sheet geometry. The method calculates forces and moments as well as detail surface pressure distributions. Improvements include the implementation of improved panel numerics for the purpose of elimination the highly nonlinear effects of ring vortices around double panel edges, and the development of a least squares procedure for damping vortex sheet geometry update instabilities. A complete description of the method is included. A variety of cases generated by the computer program implementing the method are presented which verify the mathematical assumptions of the method and which compare computed results with experimental data to verify the underlying physical assumptions made by the method.

Method for the thermal characterization, visualization, and integrity evaluation of conducting material samples or complex structures

DOEpatents

Ortiz, Marcos G.

1992-01-01

A method for modeling a conducting material sample or structure (herein called a system) as at least two regions which comprise an electrical network of resistances, for measuring electric resistance between at least two selected pairs of external leads attached to the surface of the system, wherein at least one external lead is attached to the surface of each of the regions, and, using basic circuit theory, for translating measured resistances into temperatures or thermophysical properties in corresponding regions of the system.

Method for the thermal characterization, visualization, and integrity evaluation of conducting material samples or complex structures

DOEpatents

Ortiz, M.G.

1992-11-24

Disclosed is a method for modeling a conducting material sample or structure (herein called a system) as at least two regions which comprise an electrical network of resistances, for measuring electric resistance between at least two selected pairs of external leads attached to the surface of the system, wherein at least one external lead is attached to the surface of each of the regions, and, using basic circuit theory, for translating measured resistances into temperatures or thermophysical properties in corresponding regions of the system. 16 figs.

Singularity embedding method in potential flow calculations

NASA Technical Reports Server (NTRS)

Jou, W. H.; Huynh, H.

1982-01-01

The so-called H-type mesh is used in a finite-element (or finite-volume) calculation of the potential flow past an airfoil. Due to coordinate singularity at the leading edge, a special singular trial function is used for the elements neighboring the leading edge. The results using the special singular elements are compared to those using the regular elements. It is found that the unreasonable pressure distribution obtained by the latter is removed by the embedding of the singular element. Suggestions to extend the present method to transonic cases are given.

Assessment of Methods for Estimating Risk to Birds from ...

EPA Pesticide Factsheets

The U.S. EPA Ecological Risk Assessment Support Center (ERASC) announced the release of the final report entitled, Assessment of Methods for Estimating Risk to Birds from Ingestion of Contaminated Grit Particles. This report evaluates approaches for estimating the probability of ingestion by birds of contaminated particles such as pesticide granules or lead particles (i.e. shot or bullet fragments). In addition, it presents an approach for using this information to estimate the risk of mortality to birds from ingestion of lead particles. Response to ERASC Request #16

Dense grid sibling frames with linear phase filters

NASA Astrophysics Data System (ADS)

Abdelnour, Farras

2013-09-01

We introduce new 5-band dyadic sibling frames with dense time-frequency grid. Given a lowpass filter satisfying certain conditions, the remaining filters are obtained using spectral factorization. The analysis and synthesis filterbanks share the same lowpass and bandpass filters but have different and oversampled highpass filters. This leads to wavelets approximating shift-invariance. The filters are FIR, have linear phase, and the resulting wavelets have vanishing moments. The filters are designed using spectral factorization method. The proposed method leads to smooth limit functions with higher approximation order, and computationally stable filterbanks.

Shaping a screening file for maximal lead discovery efficiency and effectiveness: elimination of molecular redundancy.

PubMed

Bakken, Gregory A; Bell, Andrew S; Boehm, Markus; Everett, Jeremy R; Gonzales, Rosalia; Hepworth, David; Klug-McLeod, Jacquelyn L; Lanfear, Jeremy; Loesel, Jens; Mathias, John; Wood, Terence P

2012-11-26

High Throughput Screening (HTS) is a successful strategy for finding hits and leads that have the opportunity to be converted into drugs. In this paper we highlight novel computational methods used to select compounds to build a new screening file at Pfizer and the analytical methods we used to assess their quality. We also introduce the novel concept of molecular redundancy to help decide on the density of compounds required in any region of chemical space in order to be confident of running successful HTS campaigns.

Fragment-Based Drug Discovery in Academia: Experiences From a Tuberculosis Programme

NASA Astrophysics Data System (ADS)

Heikkila, Timo J.; Surade, Sachin; Silvestre, Hernani L.; Dias, Marcio V. B.; Ciulli, Alessio; Bromfield, Karen; Scott, Duncan; Howard, Nigel; Wen, Shijun; Wei, Alvin Hung; Osborne, David; Abell, Chris; Blundell, Tom L.

The problems associated with neglected diseases are often compounded by increasing incidence of antibiotic resistance. Patient negligence and abuse of antibiotics has lead to explosive growth in cases of tuberculosis, with some M. tuberculosis strains becoming virtually untreatable. Structure-based drug development is viewed as cost-effective and time-consuming method for discovery and development of hits to lead compounds. In this review we will discuss the suitability of fragment-based methods for developing new chemotherapeutics against neglected diseases, providing examples from our tuberculosis programme.

Computing correct truncated excited state wavefunctions

NASA Astrophysics Data System (ADS)

Bacalis, N. C.; Xiong, Z.; Zang, J.; Karaoulanis, D.

2016-12-01

We demonstrate that, if a wave function's truncated expansion is small, then the standard excited states computational method, of optimizing one "root" of a secular equation, may lead to an incorrect wave function - despite the correct energy according to the theorem of Hylleraas, Undheim and McDonald - whereas our proposed method [J. Comput. Meth. Sci. Eng. 8, 277 (2008)] (independent of orthogonality to lower lying approximants) leads to correct reliable small truncated wave functions. The demonstration is done in He excited states, using truncated series expansions in Hylleraas coordinates, as well as standard configuration-interaction truncated expansions.

Lead poison prevention: a comparative review of brochures.

PubMed

Endres, Jeannette; Montgomery, Joe; Welch, Patricia

2002-01-01

Although eliminating lead from the environment is the most effective way to prevent lead poisoning, outreach and education also must be addressed. This study reports a consensus summary of lead-poisoning prevention topics and reading levels derived from state brochures. This information may be useful in the evaluation and design of future lead prevention brochures. A point system was used to assess the readability and topic content of 20 brochures from 11 states. Only half of the brochures were written at the targeted grade level. Frequently covered topics were wash hands and face, provide foods that contain good sources of key nutrients, and use damp cleaning methods when dusting and mopping. The findings about topics and reading levels can be used throughout the development of lead-hazard prevention brochures.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiao, Li-Na; Wang, H.C.; Shen, Y.

Nanostructured lead chalcogenides (PbX, X = Te, Se, S) were prepared via a simple hydrothermal method. The powder samples were characterized by XRD, SEM, SAED and DRS. Phase composition and microstructure analysis indicate that these samples are pure lead chalcogenides phases and have similar morphologies. These lead chalcogenides display efficient absorption in the UV-visible light range. The photocatalytic properties of lead chalcogenides nanoparticles were evaluated by the photodegradation of Congo red under UV-visible light irradiation in air atmosphere. The Congo red solution can be efficiently degraded under visible light in the presence of lead chalcogenides nanoparticles. The photocatalytic activities ofmore » lead chalcogenides generally increase with increasing their band gaps and shows no appreciable loss after repeated cycles. Our results may be useful for developing new photocatalyst systems responsive to visible light among narrow band gap semiconductors.« less

Spices as a source of lead exposure: a market-basket survey in Sri Lanka.

PubMed

Senanayake, M P; Perera, R; Liyanaarachchi, L A; Dassanayake, M P

2013-12-01

We performed a laboratory analysis of spices sold in Sri Lanka for lead content. Samples of curry powder, chili powder and turmeric powder from seven provinces, collected using the market basket survey method, underwent atomic absorption spectrometry. Blanks and standards were utilised for instrument calibration and measurement accuracy. The results were validated in two different laboratories. All samples were found to have lead levels below the US Food and Drug Administration's action level of 0.5 μg/g. Spices sold in Sri Lanka contain lead concentrations that are low and within the stipulated safety standards.

Colloidal-gold electrosensor measuring device

DOEpatents

Wegner, S.; Harpold, M.A.; McCaffrey, T.M.; Morris, S.E.; Wojciechowski, M.; Zhao, J.; Henkens, R.W.; Naser, N.; O`Daly, J.P.

1995-11-21

The present invention provides a new device for use in measuring lead levels in biological and environmental samples. Using square wave coulometry and colloidal gold particles impregnated on carbon electrodes, the present invention provides a rapid, reliable, portable and inexpensive means of detecting low lead levels. The colloidal gold modified electrodes have microelectrode array characteristics and produce significantly higher stripping detection signals for lead than are produced at bulk gold electrode surfaces. The method is effective in determining levels of lead down to at least 5 {micro}g/dL in blood samples as small as 10 {micro}L. 9 figs.

Source of lead-210 and polonium-210 in tobacco.

PubMed

Tso, T C; Harley, N; Alexander, L T

1966-08-19

Test plants were grown within a chamber enriched with radon-222 in the atmosphere, in tobacco fields with different sources of phosphate-containing fertilizer, and in culture containing lead-210 in the nutrient solution. Harvested leaves were subjected to three curing conditions. The major portion of the lead-210 in the plant was probably absorbed through the roots. Airborne radon 222 and its daughters contributed much less to the plant's content of lead-210 and of polonium-210. The stage of leaf development and the methods used to cure the leaf affected the final amount of polonium-210 in tobacco leaf.

Colloidal-gold electrosensor measuring device

DOEpatents

Wegner, Steven; Harpold, Michael A.; McCaffrey, Terence M.; Morris, Susan E.; Wojciechowski, Marek; Zhao, Junguo; Henkens, Robert W.; Naser, Najih; O'Daly, John P.

1995-01-01

The present invention provides a new device for use in measuring lead levels in biological and environmental samples. Using square wave coulometry and colloidal gold particles impregnated on carbon electrodes, the present invention provides a rapid, reliable, portable and inexpensive means of detecting low lead levels. The colloidal gold modified electrodes have microelectrode array characteristics and produce significantly higher stripping detection signals for lead than are produced at bulk gold electrode surfaces. The method is effective in determining levels of lead down to at least 5 .mu.g/dL in blood samples as small as 10 .mu.L.

Science and Technology Highlights | NREL

Science.gov Websites

Leads to Enhanced Upgrading Methods NREL's efforts to standardize techniques for bio-oil analysis inform enhanced modeling capability and affordable methods to increase energy efficiency. December 2012 NREL Meets Performance Demands of Advanced Lithium-ion Batteries Novel surface modification methods are

Impact of parasitic thermal effects on thermoelectric property measurements by Harman method.

PubMed

Kwon, Beomjin; Baek, Seung-Hyub; Kim, Seong Keun; Kim, Jin-Sang

2014-04-01

Harman method is a rapid and simple technique to measure thermoelectric properties. However, its validity has been often questioned due to the over-simplified assumptions that this method relies on. Here, we quantitatively investigate the influence of the previously ignored parasitic thermal effects on the Harman method and develop a method to determine an intrinsic ZT. We expand the original Harman relation with three extra terms: heat losses via both the lead wires and radiation, and Joule heating within the sample. Based on the expanded Harman relation, we use differential measurement of the sample geometry to measure the intrinsic ZT. To separately evaluate the parasitic terms, the measured ZTs with systematically varied sample geometries and the lead wire types are fitted to the expanded relation. A huge discrepancy (∼28%) of the measured ZTs depending on the measurement configuration is observed. We are able to separately evaluate those parasitic terms. This work will help to evaluate the intrinsic thermoelectric property with Harman method by eliminating ambiguities coming from extrinsic effects.

Prediction of the Possibility a Right-Turn Driving Behavior at Intersection Leads to an Accident by Detecting Deviation of the Situation from Usual when the Behavior is Observed

NASA Astrophysics Data System (ADS)

Hayashi, Toshinori; Yamada, Keiichi

Deviation of driving behavior from usual could be a sign of human error that increases the risk of traffic accidents. This paper proposes a novel method for predicting the possibility a driving behavior leads to an accident from the information on the driving behavior and the situation. In a previous work, a method of predicting the possibility by detecting the deviation of driving behavior from usual one in that situation has been proposed. In contrast, the method proposed in this paper predicts the possibility by detecting the deviation of the situation from usual one when the behavior is observed. An advantage of the proposed method is the number of the required models is independent of the variety of the situations. The method was applied to a problem of predicting accidents by right-turn driving behavior at an intersection, and the performance of the method was evaluated by experiments on a driving simulator.

Application of the vortex-lattice technique to the analysis of thin wings with vortex separation and thick multi-element wings

NASA Technical Reports Server (NTRS)

Smith, C. W.; Bhateley, I. C.

1976-01-01

Two techniques for extending the range of applicability of the basic vortex-lattice method are discussed. The first improves the computation of aerodynamic forces on thin, low-aspect-ratio wings of arbitrary planforms at subsonic Mach numbers by including the effects of leading-edge and tip vortex separation, characteristic of this type wing, through use of the well-known suction-analogy method of E. C. Polhamus. Comparisons with experimental data for a variety of planforms are presented. The second consists of the use of the vortex-lattice method to predict pressure distributions over thick multi-element wings (wings with leading- and trailing-edge devices). A method of laying out the lattice is described which gives accurate pressures on the top and part of the bottom surface of the wing. Limited comparisons between the result predicted by this method, the conventional lattice arrangement method, experimental data, and 2-D potential flow analysis techniques are presented.

Lead-lag cross-sectional structure and detection of correlated anticorrelated regime shifts: Application to the volatilities of inflation and economic growth rates

NASA Astrophysics Data System (ADS)

Zhou, Wei-Xing; Sornette, Didier

2007-07-01

We have recently introduced the “thermal optimal path” (TOP) method to investigate the real-time lead-lag structure between two time series. The TOP method consists in searching for a robust noise-averaged optimal path of the distance matrix along which the two time series have the greatest similarity. Here, we generalize the TOP method by introducing a more general definition of distance which takes into account possible regime shifts between positive and negative correlations. This generalization to track possible changes of correlation signs is able to identify possible transitions from one convention (or consensus) to another. Numerical simulations on synthetic time series verify that the new TOP method performs as expected even in the presence of substantial noise. We then apply it to investigate changes of convention in the dependence structure between the historical volatilities of the USA inflation rate and economic growth rate. Several measures show that the new TOP method significantly outperforms standard cross-correlation methods.

Model-free simulations of turbulent reactive flows

NASA Technical Reports Server (NTRS)

Givi, Peyman

1989-01-01

The current computational methods for solving transport equations of turbulent reacting single-phase flows are critically reviewed, with primary attention given to those methods that lead to model-free simulations. In particular, consideration is given to direct numerical simulations using spectral (Galerkin) and pseudospectral (collocation) methods, spectral element methods, and Lagrangian methods. The discussion also covers large eddy simulations and turbulence modeling.

SORPTION OF LEAD ON A HIGH AFFINITY OXIDE: MACROSCOPIC AND MICROSCOPIC STUDIES

EPA Science Inventory

Sorption of lead (Pb) was investigated on an innovative metal oxide compound using macroscopic and microscopic techniques. The objective of this study was to elucidate the sorption mechanism of Pb on the high-affinity engineered oxide with time at pH 6 employing batch methods an...

SORPTION OF LEAD ON A HIGH AFFINITY OXIDE: MACROSCOPIC AND MICROSCOPIC STUDIES (ABSTRACT)

EPA Science Inventory

Sorption of lead (Pb) was investigated on an innovative metal oxide compound using macroscopic and microscopic techniques. The objective of this study was to elucidate the sorption mechanism of Pb on the high-affinity engineered oxide with time at pH 6 employing batch methods an...

The Challenges of Developing Research Resources for Leading Vietnamese Universities

ERIC Educational Resources Information Center

Nguyen, Thi Lan Huong

2013-01-01

This paper examines the challenges of developing research resources for leading Vietnamese universities. The first part of the paper presents the background to the study, including literature review on the challenges to research resources development, and describes the research questions and research methods. The next part provides empirical…

System for agitating the acid in a lead-acid battery

DOEpatents

Weintraub, Alvin; MacCormack, Robert S.

1987-01-01

A system and method for agitating the acid in a large lead-sulfuric acid storage battery of the calcium type. An air-lift is utilized to provide the agitation. The air fed to the air-lift is humidified prior to being delivered to the air-lift.

A Discussion of Water Pollution in the United States and Mexico; with High School Laboratory Activities for Analysis of Lead, Atrazine, and Nitrate.

ERIC Educational Resources Information Center

Kelter, Paul B.; Grundman, Julie; Hage, David S.; Carr, James D.; Castro-Acuna, Carlos Mauricio

1997-01-01

Presents discussions on sources, health impacts, methods of analysis as well as lengthy discussions of lead, nitrates, and atrazine as related to water pollution and the interdisciplinary nature of the modern chemistry curriculum. (DKM)

Testing for lead in toys at day care centers.

PubMed

Sanders, Martha; Stolz, Julie; Chacon-Baker, Ashley

2013-01-01

Exposure to lead-based paint or material has been found to impact children's cognitive and behavioral development at blood lead levels far below current standards. The purpose of the project was to screen for lead in toy items in daycare centers in order to raise awareness of inside environmental lead exposures and minimize lead-based exposures for children. Occupational therapy students in a service learning class tested for lead in ten daycare or public centers using the XRF Thermo Scientific Niton XL3t, a method accepted by the Consumer Product Safety Commission (CPSC). A total of 460 items were tested over a two-month period for an average of 66 toys per setting. Fifty six (56) items tested > 100 ppm, which represented 12% of the entire sample. Items with high lead levels included selected toys constructed with lead-based paint, lead metals, plastics using lead as a color enhancer, and decorative objects. While the actual number of lead-based products is small, the cumulative exposure or habitual use may pose an unnecessary risk to children. Indoor exposures occurred for all day care centers regardless of socio-economic levels. Recommendations to minimize exposures are provided.

Blood Lead Levels and Health Problems of Lead Acid Battery Workers in Bangladesh

PubMed Central

Ahmad, Sk. Akhtar; Khan, Manzurul Haque; Khandker, Salamat; Sarwar, A. F. M.; Yasmin, Nahid; Faruquee, M. H.; Yasmin, Rabeya

2014-01-01

Introduction. Use of lead acid battery (LAB) in Bangladesh has risen with sharp rise of motor vehicles. As result, manufacture of LAB is increasing. Most of the lead used by these industries comes from recycling of LAB. Workers in LAB industry are at risk of exposure lead and thus development of lead toxicity. Objective. The objective of this study was to measure the blood lead concentration and to assess the magnitude of health problems attributable to lead toxicity among the LAB manufacturing workers. Methods. A cross-sectional study was conducted among the workers of LAB manufacturing industries located in Dhaka city. Result. Mean blood lead level (BLL) among the workers was found to be high. They were found to be suffering from a number of illnesses attributable to lead toxicity. The common illnesses were frequent headache, numbness of the limbs, colic pain, nausea, tremor, and lead line on the gum. High BLL was also found to be related to hypertension and anemia of the workers. Conclusion. High BLL and illnesses attributable to lead toxicity were prevalent amongst workers of the LAB manufacturing industries, and this requires attention especially in terms of occupational hygiene and safety. PMID:24707223

Next-to-leading-logarithmic power corrections for N -jettiness subtraction in color-singlet production

NASA Astrophysics Data System (ADS)

Boughezal, Radja; Isgrò, Andrea; Petriello, Frank

2018-04-01

We present a detailed derivation of the power corrections to the factorization theorem for the 0-jettiness event shape variable T . Our calculation is performed directly in QCD without using the formalism of effective field theory. We analytically calculate the next-to-leading logarithmic power corrections for small T at next-to-leading order in the strong coupling constant, extending previous computations which obtained only the leading-logarithmic power corrections. We address a discrepancy in the literature between results for the leading-logarithmic power corrections to a particular definition of 0-jettiness. We present a numerical study of the power corrections in the context of their application to the N -jettiness subtraction method for higher-order calculations, using gluon-fusion Higgs production as an example. The inclusion of the next-to-leading-logarithmic power corrections further improves the numerical efficiency of the approach beyond the improvement obtained from the leading-logarithmic power corrections.

More evidence of unpublished industry studies of lead smelter/refinery workers

PubMed Central

2015-01-01

Background Lead smelter/refinery workers in the US have had significant exposure to lead and are an important occupational group to study to understand the health effects of chronic lead exposure in adults. Recent research found evidence that studies of lead smelter/refinery workers have been conducted but not published. This paper presents further evidence for this contention. Objectives To present further evidence of industry conducted, unpublished epidemiologic studies of lead smelter/refinery workers and health outcomes. Methods Historical research relying on primary sources such as internal industry documents and published studies. Results ASARCO smelter/refinery workers were studied in the early 1980s and found to have increased risk of lung cancer and stroke in one study, but not in another. Conclusions Because occupational lead exposure is an on-going concern for US and overseas workers, all epidemiologic studies should be made available to evaluate and update occupational health and safety standards. PMID:26070220

Childhood lead poisoning - United States: report to the Congress by the Agency for Toxic Substances and Disease Registry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The long-term consequences of unabated exposures to environmental lead sources can be serious, particularly for children. Recent scientific studies have shown a progressive decline in the lowest exposure levels of lead at which adverse effects can be reliably detected in children. In recognition of this, Congress directed the Agency for Toxic Substances and Disease Registry (ATSDR), in consultation with the Environmental Protection Agency (EPA), to examine the nature and extent of childhood lead poisoning in the United States. The study was to address such areas as the long-term health implications of environmental lead exposure in children, the extent of leadmore » intoxication of children in terms of geographic areas and sources of lead in the United States, and methods and strategies for removing lead from the environment of US children. This article summarizes the key findings of the report.« less

Lead poisoning in children.

PubMed

Warniment, Crista; Tsang, Katrina; Galazka, Sim S

2010-03-15

The prevalence and severity of childhood lead poisoning have been greatly reduced since the removal of lead from paint and gasoline in the 1970s. Despite these efforts, approximately 310,000 U.S. children younger than five years have elevated blood lead levels. Health care professionals should perform targeted screening for lead poisoning in children who are Medicaid-enrolled or -eligible, foreign born, or identified as high risk by the Centers for Disease Control and Prevention (CDC) location-specific recommendations or by a personal risk questionnaire. Venous sampling is the preferred method for measuring blood lead levels, but a carefully collected finger-stick sample is an acceptable alternative. Capillary samples of elevated levels should be confirmed by a venous sample. The CDC recommends that the threshold for follow-up and intervention of lead poisoning be a blood lead level of 10 microg per dL or higher. Recommendations for treatment of elevated blood levels include a thorough environmental investigation, laboratory testing when appropriate, iron supplementation for iron-deficient children, and chelation therapy for blood lead levels of 45 microg per dL or more. Prevention consists of education and avoidance of lead-contaminated products.

Left heart pacing lead implantation using subxiphoid videopericardioscopy.

PubMed

Zenati, Marco A; Bonanomi, Gianluca; Chin, Albert K; Schwartzman, David

2003-09-01

Recent clinical data support the utility of left heart pacing. The transvenous approach for left heart pacing lead implantation is imperfect. A direct epicardial approach may have advantages, but heretofore its utility has been limited because of the requirement for thoracotomy. We sought to examine the feasibility of a method for epicardial lead implantation that did not require thoracotomy. In five large swine, percutaneous access to the epicardium was achieved with subxiphoid videopericardioscopy, using a device that marries endoscopy with a port through which pacing leads could be introduced. In each animal, standard, active fixation pacing leads were implanted onto the left atrium and ventricle. The atrial lead was implanted at the base of the appendage. The ventricular lead was implanted on the anterior, lateral, and inferior walls. Continuous direct visualization of the epicardium provided guidance for lead localization and fixation, including avoidance of complications such as trauma to epicardial coronary vessels. Capture thresholds were uniformly low. Postmortem examination demonstrated anatomically accurate, uncomplicated lead fixation. Using subxiphoid videopericardioscopy, uncomplicated, anatomically accurate left heart epicardial pacing lead implantation can be achieved without thoracotomy.

Spiral lead platen robotic end effector

NASA Technical Reports Server (NTRS)

Beals, David C. (Inventor)

1990-01-01

A robotic end effector is disclosed which makes use of a rotating platen with spiral leads used to impact lateral motion to gripping fingers. Actuation is provided by the contact of rolling pins with the walls of the leads. The use of the disclosed method of actuation avoids jamming and provides excellent mechanical advantage while remaining light in weight and durable. The entire end effector is compact and easily adapted for attachment to robotic arms currently in use.

Staining of Tissue Sections for Electron Microscopy with Heavy Metals

PubMed Central

Watson, Michael L.

1958-01-01

Descriptions of three heavy metal stains and methods of application to tissue sections for electron microscopy are presented. Lead hydroxide stains rather selectively two types of particles in liver: those associated with the endoplasmic reticulum and containing ribonucleic acid and other somewhat larger particles. Barium hydroxide emphasizes certain bodies within vesicles of the Golgi region of hepatic cells. Alkalized lead acetate is useful as a general stain, as are also lead and barium hydroxides. PMID:13610936

Environmental Assessment of Lead at Camp Edwards, Massachusetts, Small Arms Ranges

DTIC Science & Technology

2007-08-01

phosphates in soils as a method to immobilize lead. Environmental Science and Technology. 28(4):646–654. Rühling, A., and G. Tyler. 1973. Heavy metal ...control of heavy metals in a sandy soil . Environmental Science and Technology. 36(22):4804– 4810. Xia, K., W. Bleam, and P. A. Helmke. 1997. Studies...Military Training Sources of Lead and Soil Distribution at Camp Edwards ..............38 3.3 Projects Specific to Camp Edwards Small Arms Ranges

Mathematical foundations of hybrid data assimilation from a synchronization perspective

NASA Astrophysics Data System (ADS)

Penny, Stephen G.

2017-12-01

The state-of-the-art data assimilation methods used today in operational weather prediction centers around the world can be classified as generalized one-way coupled impulsive synchronization. This classification permits the investigation of hybrid data assimilation methods, which combine dynamic error estimates of the system state with long time-averaged (climatological) error estimates, from a synchronization perspective. Illustrative results show how dynamically informed formulations of the coupling matrix (via an Ensemble Kalman Filter, EnKF) can lead to synchronization when observing networks are sparse and how hybrid methods can lead to synchronization when those dynamic formulations are inadequate (due to small ensemble sizes). A large-scale application with a global ocean general circulation model is also presented. Results indicate that the hybrid methods also have useful applications in generalized synchronization, in particular, for correcting systematic model errors.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendt, Joel Robert; Hadley, G. Ronald; Samora, Sally

Plasmonic structures open up new opportunities in photonic devices, sometimes offering an alternate method to perform a function and sometimes offering capabilities not possible with standard optics. In this LDRD we successfully demonstrated metal coatings on optical surfaces that do not adversely affect the transmission of those surfaces at the design frequency. This technology could be applied as an RF noise blocking layer across an optical aperture or as a method to apply an electric field to an active electro-optic device without affecting optical performance. We also demonstrated thin optical absorbers using similar patterned surfaces. These infrared optical antennas showmore » promise as a method to improve performance in mercury cadmium telluride detectors. Furthermore, these structures could be coupled with other components to lead to direct rectification of infrared radiation. This possibility leads to a new method for infrared detection and energy harvesting of infrared radiation.« less

Transonic pressure measurements and comparison of theory to experiment for an arrow-wing configuration. Volume 1: Experimental data report, base configuration and effects of wing twist and leading-edge configuration. [wind tunnel tests, aircraft models

NASA Technical Reports Server (NTRS)

Manro, M. E.; Manning, K. J. R.; Hallstaff, T. H.; Rogers, J. T.

1975-01-01

A wind tunnel test of an arrow-wing-body configuration consisting of flat and twisted wings, as well as a variety of leading- and trailing-edge control surface deflections, was conducted at Mach numbers from 0.4 to 1.1 to provide an experimental pressure data base for comparison with theoretical methods. Theory-to-experiment comparisons of detailed pressure distributions were made using current state-of-the-art attached and separated flow methods. The purpose of these comparisons was to delineate conditions under which these theories are valid for both flat and twisted wings and to explore the use of empirical methods to correct the theoretical methods where theory is deficient.

Mathematical foundations of hybrid data assimilation from a synchronization perspective.

PubMed

Penny, Stephen G

2017-12-01

The state-of-the-art data assimilation methods used today in operational weather prediction centers around the world can be classified as generalized one-way coupled impulsive synchronization. This classification permits the investigation of hybrid data assimilation methods, which combine dynamic error estimates of the system state with long time-averaged (climatological) error estimates, from a synchronization perspective. Illustrative results show how dynamically informed formulations of the coupling matrix (via an Ensemble Kalman Filter, EnKF) can lead to synchronization when observing networks are sparse and how hybrid methods can lead to synchronization when those dynamic formulations are inadequate (due to small ensemble sizes). A large-scale application with a global ocean general circulation model is also presented. Results indicate that the hybrid methods also have useful applications in generalized synchronization, in particular, for correcting systematic model errors.

Irreducible Green's functions method for a quantum dot coupled to metallic and superconducting leads

NASA Astrophysics Data System (ADS)

Górski, Grzegorz; Kucab, Krzysztof

2017-05-01

Using irreducible Green's functions (IGF) method we analyse the Coulomb interaction dependence of the spectral functions and the transport properties of a quantum dot coupled to isotropic superconductor and metallic leads (SC-QD-N). The irreducible Green's functions method is the modification of classical equation of motion technique. The IGF scheme is based on differentiation of double-time Green's functions, both over the primary and secondary times. The IGF method allows to obtain the spectral functions for equilibrium and non-equilibrium impurity Anderson model used for SC-QD-N system. By the numerical computations, we show the change of spectral and the anomalous densities under the influence of the Coulomb interactions. The observed sign change of the anomalous spectral density can be used as the criterion of the SC singlet-Kondo singlet transition.

A Method for Estimating Zero-Flow Pressure and Intracranial Pressure

PubMed Central

Caren, Marzban; Paul, Raymond Illian; David, Morison; Anne, Moore; Michel, Kliot; Marek, Czosnyka; Pierre, Mourad

2012-01-01

Background It has been hypothesized that critical closing pressure of cerebral circulation, or zero-flow pressure (ZFP), can estimate intracranial pressure (ICP). One ZFP estimation method employs extrapolation of arterial blood pressure versus blood-flow velocity. The aim of this study is to improve ICP predictions. Methods Two revisions are considered: 1) The linear model employed for extrapolation is extended to a nonlinear equation, and 2) the parameters of the model are estimated by an alternative criterion (not least-squares). The method is applied to data on transcranial Doppler measurements of blood-flow velocity, arterial blood pressure, and ICP, from 104 patients suffering from closed traumatic brain injury, sampled across the United States and England. Results The revisions lead to qualitative (e.g., precluding negative ICP) and quantitative improvements in ICP prediction. In going from the original to the revised method, the ±2 standard deviation of error is reduced from 33 to 24 mm Hg; the root-mean-squared error (RMSE) is reduced from 11 to 8.2 mm Hg. The distribution of RMSE is tighter as well; for the revised method the 25th and 75th percentiles are 4.1 and 13.7 mm Hg, respectively, as compared to 5.1 and 18.8 mm Hg for the original method. Conclusions Proposed alterations to a procedure for estimating ZFP lead to more accurate and more precise estimates of ICP, thereby offering improved means of estimating it noninvasively. The quality of the estimates is inadequate for many applications, but further work is proposed which may lead to clinically useful results. PMID:22824923

Synthesis and characterisation of nano structure lead (II) ion-imprinted polymer as a new sorbent for selective extraction and preconcentration of ultra trace amounts of lead ions from vegetables, rice, and fish samples.

PubMed

Behbahani, Mohammad; Bagheri, Akbar; Taghizadeh, Mohsen; Salarian, Mani; Sadeghi, Omid; Adlnasab, Laleh; Jalali, Kobra

2013-06-01

This paper describes the preparation of new Pb(II)-imprinted polymeric particles using 2-vinylpyridine as a functional monomer, ethylene glycol dimethacrylate as the cross-linker, 2,2'- azobisisobutyronitrile as the initiator, diphenylcarbazone as the ligand, acetonitril as the solvent, and Pb(NO(3))(2) as the template ion, through bulk polymerisation technique. The imprinted lead ions were removed from the polymeric matrix using 5 mL of HCl (2 mol.L(-1)) as the eluting solvent. The lead ion concentration was determined by flame atomic absorption spectrometry. Optimum pH for maximum sorption was obtained at 6.0. Sorption and desorption of Pb(II) ions on the IIP particles were quite fast and achieved fully over 5 min. In the proposed method, the maximum sorbent capacity of the ion-imprinted polymer was calculated to be 75.4 mg g(-1). The preconcentration factor, relative standard deviation, and limit of detection of the method were found to be 245, 2.1%, and 0.42 ng mL(-1), respectively. The prepared ion-imprinted polymer particles have an increased selectivity toward Pb(II) ions over a range of competing metal ions with the same charge and similar ionic radius. This ion-imprinted polymer is an efficient solid phase for extraction and preconcentration of lead ions in complex matrixes. For proving that the proposed method is reliable, a wide range of food samples with different and complex matrixes was used. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Guided Autobiography Method: A Learning Experience

ERIC Educational Resources Information Center

Thornton, James E.

2008-01-01

This article discusses the proposition that learning is an unexplored feature of the guided autobiography method and its developmental exchange. Learning, conceptualized and explored as the embedded and embodied processes, is essential in narrative activities of the guided autobiography method leading to psychosocial development and growth in…

BCI`s RBSM test methods: Eight years in the making

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1993-03-01

RBSM stands for recombinant battery separator mat. This is the acronym chosen after a lot of debate during eight years of committee work to develop test methods to characterize separators which are used in valve regulated lead acid batteries. This paper discusses the test methods.

Present and future of the undergraduate ophthalmology curriculum: a survey of UK medical schools

PubMed Central

Hill, Sophie; Dennick, Reg

2017-01-01

Objectives To investigate the current undergraduate ophthalmology curricula provided by the UK medical schools, evaluate how they compare with the guidelines of the Royal College of Ophthalmologists (RCOphth) and International Council for Ophthalmology (ICO), and determine the views of the UK ophthalmology teaching leads on the future direction of the curriculum. Methods A cross-sectional questionnaire was sent to teaching leads in 31 medical schools across the UK. The questionnaire evaluated eight themes of the curriculum: content and learning outcomes, communication of learning outcomes, organisation of the curriculum, assessment, educational resources, teaching methods used, and the educational environment. The ophthalmology teaching leads were also asked their opinion on the current and future management of the curriculum. These were compared with RCOphth and ICO guidelines and descriptive statistical analysis performed. Results A response rate of 93% (n=29/31) was achieved. The knowledge and clinical skills taught by the UK medical schools match the  RCOphth guidelines, but fail to meet the ICO recommendations. A diverse range of assessment methods are used by UK medical schools during ophthalmology rotations. Variation was also observed in the organisation and methods of ophthalmology teaching.  However, a significant consensus about the future direction of the curriculum was reported by teaching leads. Conclusions Comprehensive RCOphth guidance, and resource sharing between medical schools could help to ensure ophthalmology’s continuing presence in the medical curriculum and improve the effectiveness of undergraduate ophthalmology teaching, while reducing the workload of local teaching departments and medical schools.  PMID:29103017

Target-responsive DNAzyme cross-linked hydrogel for visual quantitative detection of lead.

PubMed

Huang, Yishun; Ma, Yanli; Chen, Yahong; Wu, Xuemeng; Fang, Luting; Zhu, Zhi; Yang, Chaoyong James

2014-11-18

Because of the severe health risks associated with lead pollution, rapid, sensitive, and portable detection of low levels of Pb(2+) in biological and environmental samples is of great importance. In this work, a Pb(2+)-responsive hydrogel was prepared using a DNAzyme and its substrate as cross-linker for rapid, sensitive, portable, and quantitative detection of Pb(2+). Gold nanoparticles (AuNPs) were first encapsulated in the hydrogel as an indicator for colorimetric analysis. In the absence of lead, the DNAzyme is inactive, and the substrate cross-linker maintains the hydrogel in the gel form. In contrast, the presence of lead activates the DNAzyme to cleave the substrate, decreasing the cross-linking density of the hydrogel and resulting in dissolution of the hydrogel and release of AuNPs for visual detection. As low as 10 nM Pb(2+) can be detected by the naked eye. Furthermore, to realize quantitative visual detection, a volumetric bar-chart chip (V-chip) was used for quantitative readout of the hydrogel system by replacing AuNPs with gold-platinum core-shell nanoparticles (Au@PtNPs). The Au@PtNPs released from the hydrogel upon target activation can efficiently catalyze the decomposition of H2O2 to generate a large volume of O2. The gas pressure moves an ink bar in the V-chip for portable visual quantitative detection of lead with a detection limit less than 5 nM. The device was able to detect lead in digested blood with excellent accuracy. The method developed can be used for portable lead quantitation in many applications. Furthermore, the method can be further extended to portable visual quantitative detection of a variety of targets by replacing the lead-responsive DNAzyme with other DNAzymes.

Evolution of efficient methods to sample lead sources, such as house dust and hand dust, in the homes of children

DOE Office of Scientific and Technical Information (OSTI.GOV)

Que Hee, S.S.; Peace, B.; Clark, C.S.

Efficient sampling methods to recover lead-containing house dust and hand dust have been evolved so that sufficient lead is collected for analysis and to ensure that correlational analyses linking these two parameters to blood lead are not dependent on the efficiency of sampling. Precise collection of loose house dust from a 1-unit area (484 cmS) with a Tygon or stainless steel sampling tube connected to a portable sampling pump (1.2 to 2.5 liters/min) required repetitive sampling (three times). The Tygon tube sampling technique for loose house dust <177 m in diameter was around 72% efficient with respect to dust weightmore » and lead collection. A representative house dust contained 81% of its total weight in this fraction. A single handwipe for applied loose hand dust was not acceptably efficient or precise, and at least three wipes were necessary to achieve recoveries of >80% of the lead applied. House dusts of different particle sizes <246 m adhered equally well to hands. Analysis of lead-containing material usually required at least three digestions/decantations using hot plate or microwave techniques to allow at least 90% of the lead to be recovered. It was recommended that other investigators validate their handwiping, house dust sampling, and digestion techniques to facilitate comparison of results across studies. The final methodology for the Cincinnati longitudinal study was three sampling passes for surface dust using a stainless steel sampling tube; three microwave digestion/decantations for analysis of dust and paint; and three wipes with handwipes with one digestion/decantation for the analysis of six handwipes together.« less

Arctic sea ice leads from advanced very high resolution radiometer images

NASA Technical Reports Server (NTRS)

Lindsay, R. W.; Rothrock, D. A.

1995-01-01

A large number of advanced very high resolution radiometer (AVHRR) images from throughout 1989 are analyzed to determine lead characteristics. The units of analysis are square 200-km cells, and there are 270 such cells in the data set. Clouds are masked manually. Leads determine from images of the potential open water delta, a scaled version of the surface temperature or albedo that weights thin ice by its thermal or brightness impact. The lead fraction is determined as the mean delta, the monthly mean lead fraction ranges from 0.02 in winter to 0.06 in summer in the central Arctic and is near 0.08 in the winter in the peripheral seas. A method of accounting for lead width sampling errors due to the finite sample areas is introduced. In the central Arctic the observed mean lead width for a threshold of delta = 0.1 ranges from 2 or 3 km (near the resolution of the instrument) in the winter to 6 km in the summer. In the peripheral seas it is about 5 km in the winter. Width distributions are often more heavily weighted in the tail than exponential distributions and are well approximated by a power law. The along-track, number density power law N = aw(exp -6) has a mean exponent of b = 1.60 (standard deviation 0.18) and shows some seasonal variability. Mean floe widths in the central Arctic are 40 to 50 km in the winter, dropping to about 10 km in the summer. For floes the power law has a mean exponent of 0.93 and exhibits a clearer annual cycle. Lead orientation is determined with a method based on the direction of maximum extent.

Anaerobic microbial dissolution of lead and production of organic acids

DOEpatents

Francis, Arokiasamy J.; Dodge, Cleveland; Chendrayan, Krishnachetty; Quinby, Helen L.

1988-01-01

The present invention relates to an anaerobic bacterial culture of Clostridium sp. ATCC No. 53464 which solubilizes lead oxide under anaerobic conditions in coal and industrial wastes and therefore presents a method of removing lead from such wastes before they are dumped into the environment. The rate of lead dissolution during logarithmic growth of the bacteria in 40 ml medium containing 3.32 .mu.moles of lead as lead oxide was 0.042 .mu.moles ml.sup.-1 hr.sup.-1. Dissolution of lead oxide by the bacterial isolate is due to the production of metabolites and acidity in the culture medium. The major metabolites are acetic, butyric and lactic acid. Clostridium sp. ATCC No. 53464 can be used in the recovery of strategic metals from ores and wastes and also for the production of lactic acid for commercial purposes. The process yields large quantities of lactic acid as well as lead complexed in a stable form with said acids.

Design of Current Leads for the MICE Coupling Magnet

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Li; Li, L.K.; Wu, Hong

2008-04-02

A pair of superconducting coupling magnets will be part of the Muon Ionization Cooling Experiment (MICE). They were designed and will be constructed by the Institute of Cryogenics and Superconductivity Technology, Harbin Institute of Technology, in collaboration with Lawrence Berkeley National Laboratory. The coupling magnet is to be cooled by using cryocoolers at 4.2K. In order to reduce the heat leak to the 4.2K cold mass from 300 K, a pair of current leads composed of conventional copper leads and high temperature superconductor (HTS) leads will be used to supply current to the magnet. This paper presents the optimization ofmore » the conventional conduction-cooled metal leads for the coupling magnet. Analyses on heat transfer down the leads using theoretical method and numerical simulation were carried out. The stray magnetic field around the HTS leads has been calculated and effects of the magnetic field on the performance of the HTS leads has also been analyzed.« less

Removal of Lead from Water Using Calcium Alginate Beads Doped with Hydrazine Sulphate-Activated Red Mud as Adsorbent

PubMed Central

2017-01-01

Calcium alginate beads doped with hydrazine sulphate-treated red mud are investigated as adsorbent for extracting lead ions from water using batch methods of extraction. Different extraction conditions are optimised for maximum lead extraction. Substantial amount of lead is removed, and the adsorption ability is found to be 138.6 mg/g. Surface characterization using FTIR, EDX, and FESEM confirms that lead is “onto” the surface of the adsorbent. Thermodynamic parameters, adsorption isotherms, and kinetics of adsorption are analysed. Adsorption is “physisorption” in nature and spontaneous. The adsorbent developed can be regenerated using 0.1 M HCl. Thus regenerated adsorbent can be used as the adsorbent for further removal of lead at least 10 times, and this enables the complete removal of lead from water by repetitive use of the regenerated adsorbent. The beads facilitate the easy filtration. The methodology developed is successfully applied for removing lead from industrial waste waters. PMID:29527385

Evaluating wood failure in plywood shear by optical image analysis

Treesearch

Charles W. McMillin

1984-01-01

This exploratory study evaulates the potential of using an automatic image analysis method to measure percent wood failure in plywood shear specimens. The results suggest that this method my be as accurate as the visual method in tracking long-term gluebond quality. With further refinement, the method could lead to automated equipment replacing the subjective visual...

A simulation-based evaluation of methods for inferring linear barriers to gene flow

Treesearch

Christopher Blair; Dana E. Weigel; Matthew Balazik; Annika T. H. Keeley; Faith M. Walker; Erin Landguth; Sam Cushman; Melanie Murphy; Lisette Waits; Niko Balkenhol

2012-01-01

Different analytical techniques used on the same data set may lead to different conclusions about the existence and strength of genetic structure. Therefore, reliable interpretation of the results from different methods depends on the efficacy and reliability of different statistical methods. In this paper, we evaluated the performance of multiple analytical methods to...

Nodal Analysis Optimization Based on the Use of Virtual Current Sources: A Powerful New Pedagogical Method

ERIC Educational Resources Information Center

Chatzarakis, G. E.

2009-01-01

This paper presents a new pedagogical method for nodal analysis optimization based on the use of virtual current sources, applicable to any linear electric circuit (LEC), regardless of its complexity. The proposed method leads to straightforward solutions, mostly arrived at by inspection. Furthermore, the method is easily adapted to computer…

A Metallurgical Study of Nāga Bhasma

PubMed Central

Singh Gautam, Dev Nath

2017-01-01

Background: The metal Nāga (Lead) is being used by Indians since ancient times. Its external and internal uses have been described in Caraka, Suśruta and other Ayurvedic Saṃhitā. According to most of the Rasa texts, Nāga Bhasma and its formulations are used in many diseases such as Prameha, Jvara, Gulma, Śukrameha etc. Objectives: In the present study, Nāga Bhasma was prepared by the traditional Puṭa method (TPM) and by the electric muffle furnace Puṭa method (EMFPM) and standardized using Metallographic studies. Doing so helps in the study of the microstructure of Nāga Bhasma and also helps in the identification of the metal particles along with the nature of compound formed during the Māraṇa (Bhasmīkaraṇa) process. Setting and Design: Different samples from initial raw material to final product of Nāga Bhasma were collected during the pharmaceutical process (1st, 30th and 60th Puṭa) from both methods i.e. TPM and EMFPM. Samples from both methods were studied using metallographic examination. Materials and Methods: The processing of the Nāga Bhasma (ṣaṣṭipuṭa) was done according to Ānanda Kanda[9] Samples from the raw material i.e. Aśodhita Nāga (raw Lead) and that processed after 1st, 30th and 60th Puṭa from both methods i.e. traditional Puṭa method (using heat from burning of cow dung cakes) and electric muffle furnace Puṭa method were taken. They were mounted on self hardening acrylic base. After careful polishing to obtain scratch free surface of product, they were used for metallurgical study. Conclusion: This study shows that traditional Puṭa method may be better than electric muffle furnace Puṭa method because of more homogeneous distribution of Lead sulphide in the Nāga Bhasma which is prepared by traditional method. PMID:29269968

Comparison of a wipe method with and without a rinse to recover wall losses in closed face 37-mm cassettes used for sampling lead dust particulates

PubMed Central

Ceballos, Diana; King, Bradley; Beaucham, Catherine; Brueck, Scott E.

2015-01-01

Closed-face 37-millimeter (mm) polystyrene cassettes are often used for exposure monitoring of metal particulates. Several methods have been proposed to account for the wall loss in air sampling cassettes, including rinsing, wiping, within-cassette dissolution, and an internal capsule fused to the filter that could be digested with the filter. Until internal capsules replace filters, other methods for assessing wall losses may be considered. To determine if rinsing and wiping or wiping alone is adequate to determine wall losses on cassettes, we collected 54 full-shift area air samples at a battery recycling facility. We collected six replicate samples at three locations within the facility for 3 consecutive days. The wall losses of three replicate cassettes from each day-location were analyzed following a rinse and two consecutive wipes. The wall losses of the other three replicates from each day-location were analyzed following two consecutive wipes only. Mixed-cellulose ester membrane filter, rinse, and wipes were analyzed separately following NIOSH Method 7303. We found an average of 29% (range: 8%–54%) recovered lead from the cassette walls for all samples. We also found that rinsing prior to wiping the interior cassette walls did not substantially improve recovery of wall losses compared to wiping alone. A rinse plus one wipe recovered on average 23% (range: 13%–33%) of the lead, while one wipe alone recovered on average 21% (range: 16%–22%). Similarly we determined that a second wipe did not provide substantial additional recovery of lead (average: 4%, range: 0.4%–19%) compared to the first wipe disregarding the rinse (average: 18%, range: 4%–39%). We concluded that when an internal capsule is not used, wall losses of lead dust in air sampling cassettes can be adequately recovered by wiping the internal wall surfaces of the cassette with a single wipe. PMID:26125330

Adsorption of lead onto smectite from aqueous solution.

PubMed

Mhamdi, M; Galai, H; Mnasri, N; Elaloui, E; Trabelsi-Ayadi, M

2013-03-01

The purpose of this research is to study the effect of a new method of adsorption using membrane filtration to determine the maximum amount of lead adsorbed by clay and investigate the behavior of the clay after adsorption of the said metal. Treatment of wastewater contaminated with heavy metals depends on the characteristics of the effluent, the amount of final discharge, the cost of treatment, and the compatibility of the treatment process. The process of adsorption of heavy metals by clays may be a simple, selective, and economically viable alternative to the conventional physical-chemical treatment. This is justified by the importance of the surface developed by this material, the presence of negative charges on the said surface, the possibility of ion exchange taking place, and its wide availability in nature. The removal of lead from wastewater was studied by using the adsorption technique and using clay as the adsorbent. A method was optimized for adsorption through a membrane approaching natural adsorption. This new method is simple, selective, and the lead adsorption time is about 3 days. The various properties of clay were determined. It was observed that the cation exchange capacity of the clay was 56 meq/100 g of hydrated clay for the raw sample and 82 meq/100 g for the purified sample. The total surface area determined by the methylene blue method was equal to 556 and 783 m(2)/g for the raw and purified samples, respectively. The adsorption kinetics depends on several parameters. The Pb(II) clay, obeys the Langmuir, Freundlich, and the Elovich adsorption isotherms with high regression coefficients. The use of this adsorbent notably decreases the cost of treatment. It was concluded that clay shows a strong adsorption capacity on Pb(II), the maximum interaction occurring with purified clay treated at high concentration of lead. It is proposed that this adsorption through a membrane be extended for the treatment of effluents containing other metals.

Computation of NLO processes involving heavy quarks using Loop-Tree Duality

NASA Astrophysics Data System (ADS)

Driencourt-Mangin, Félix

2017-03-01

We present a new method to compute higher-order corrections to physical cross-sections, at Next-to-Leading Order and beyond. This method, based on the Loop Tree Duality, leads to locally integrable expressions in four dimensions. By introducing a physically motivated momentum mapping between the momenta involved in the real and the virtual contributions, infrared singularities naturally cancel at integrand level, without the need to introduce subtraction counter-terms. Ultraviolet singularities are dealt with by using dual representations of suitable counter-terms, with some subtleties regarding the self-energy contributions. As an example, we apply this method to compute the 1 → 2 decay rate in the context of a scalar toy model with massive particles.

Crystallization of bFGF-DNA Aptamer Complexes Using a Sparse Matrix Designed for Protein-Nucleic Acid Complexes

NASA Technical Reports Server (NTRS)

Cannone, Jaime J.; Barnes, Cindy L.; Achari, Aniruddha; Kundrot, Craig E.; Whitaker, Ann F. (Technical Monitor)

2001-01-01

The Sparse Matrix approach for obtaining lead crystallization conditions has proven to be very fruitful for the crystallization of proteins and nucleic acids. Here we report a Sparse Matrix developed specifically for the crystallization of protein-DNA complexes. This method is rapid and economical, typically requiring 2.5 mg of complex to test 48 conditions. The method was originally developed to crystallize basic fibroblast growth factor (bFGF) complexed with DNA sequences identified through in vitro selection, or SELEX, methods. Two DNA aptamers that bind with approximately nanomolar affinity and inhibit the angiogenic properties of bFGF were selected for co-crystallization. The Sparse Matrix produced lead crystallization conditions for both bFGF-DNA complexes.

An Old Story in the Parallel Synthesis World: An Approach to Hydantoin Libraries.

PubMed

Bogolubsky, Andrey V; Moroz, Yurii S; Savych, Olena; Pipko, Sergey; Konovets, Angelika; Platonov, Maxim O; Vasylchenko, Oleksandr V; Hurmach, Vasyl V; Grygorenko, Oleksandr O

2018-01-08

An approach to the parallel synthesis of hydantoin libraries by reaction of in situ generated 2,2,2-trifluoroethylcarbamates and α-amino esters was developed. To demonstrate utility of the method, a library of 1158 hydantoins designed according to the lead-likeness criteria (MW 200-350, cLogP 1-3) was prepared. The success rate of the method was analyzed as a function of physicochemical parameters of the products, and it was found that the method can be considered as a tool for lead-oriented synthesis. A hydantoin-bearing submicromolar primary hit acting as an Aurora kinase A inhibitor was discovered with a combination of rational design, parallel synthesis using the procedures developed, in silico and in vitro screenings.

Analysis and computation of a least-squares method for consistent mesh tying

DOE PAGES

Day, David; Bochev, Pavel

2007-07-10

We report in the finite element method, a standard approach to mesh tying is to apply Lagrange multipliers. If the interface is curved, however, discretization generally leads to adjoining surfaces that do not coincide spatially. Straightforward Lagrange multiplier methods lead to discrete formulations failing a first-order patch test [T.A. Laursen, M.W. Heinstein, Consistent mesh-tying methods for topologically distinct discretized surfaces in non-linear solid mechanics, Internat. J. Numer. Methods Eng. 57 (2003) 1197–1242]. This paper presents a theoretical and computational study of a least-squares method for mesh tying [P. Bochev, D.M. Day, A least-squares method for consistent mesh tying, Internat. J.more » Numer. Anal. Modeling 4 (2007) 342–352], applied to the partial differential equation -∇ 2φ+αφ=f. We prove optimal convergence rates for domains represented as overlapping subdomains and show that the least-squares method passes a patch test of the order of the finite element space by construction. To apply the method to subdomain configurations with gaps and overlaps we use interface perturbations to eliminate the gaps. Finally, theoretical error estimates are illustrated by numerical experiments.« less

Video-Based Fingerprint Verification

PubMed Central

Qin, Wei; Yin, Yilong; Liu, Lili

2013-01-01

Conventional fingerprint verification systems use only static information. In this paper, fingerprint videos, which contain dynamic information, are utilized for verification. Fingerprint videos are acquired by the same capture device that acquires conventional fingerprint images, and the user experience of providing a fingerprint video is the same as that of providing a single impression. After preprocessing and aligning processes, “inside similarity” and “outside similarity” are defined and calculated to take advantage of both dynamic and static information contained in fingerprint videos. Match scores between two matching fingerprint videos are then calculated by combining the two kinds of similarity. Experimental results show that the proposed video-based method leads to a relative reduction of 60 percent in the equal error rate (EER) in comparison to the conventional single impression-based method. We also analyze the time complexity of our method when different combinations of strategies are used. Our method still outperforms the conventional method, even if both methods have the same time complexity. Finally, experimental results demonstrate that the proposed video-based method can lead to better accuracy than the multiple impressions fusion method, and the proposed method has a much lower false acceptance rate (FAR) when the false rejection rate (FRR) is quite low. PMID:24008283

A Noninvasive Isotopic Approach to Estimate the Bone Lead Contribution to Blood in Children: Implications for Assessing the Efficacy of Lead Abatement

PubMed Central

Gwiazda, Roberto; Campbell, Carla; Smith, Donald

2005-01-01

Lead hazard control measures to reduce children’s exposure to household lead sources often result in only limited reductions in blood lead levels. This may be due to incomplete remediation of lead sources and/or to the remobilization of lead stores from bone, which may act as an endogenous lead source that buffers reductions in blood lead levels. Here we present a noninvasive isotopic approach to estimate the magnitude of the bone lead contribution to blood in children following household lead remediation. In this approach, lead isotopic ratios of a child’s blood and 5-day fecal samples are determined before and after a household intervention aimed at reducing the child’s lead intake. The bone lead contribution to blood is estimated from a system of mass balance equations of lead concentrations and isotopic compositions in blood at the different times of sample collection. The utility of this method is illustrated with three cases of children with blood lead levels in the range of 18–29 μg/dL. In all three cases, the release of lead from bone supported a substantial fraction of the measured blood lead level postintervention, up to 96% in one case. In general, the lead isotopic compositions of feces matched or were within the range of the lead isotopic compositions of the household dusts with lead loadings exceeding U.S. Environmental Protection Agency action levels. This isotopic agreement underscores the utility of lead isotopic measurements of feces to identify household sources of lead exposure. Results from this limited number of cases support the hypothesis that the release of bone lead into blood may substantially buffer the decrease in blood lead levels expected from the reduction in lead intake. PMID:15626656

Quantum chemical approaches in structure-based virtual screening and lead optimization

NASA Astrophysics Data System (ADS)

Cavasotto, Claudio N.; Adler, Natalia S.; Aucar, Maria G.

2018-05-01

Today computational chemistry is a consolidated tool in drug lead discovery endeavors. Due to methodological developments and to the enormous advance in computer hardware, methods based on quantum mechanics (QM) have gained great attention in the last 10 years, and calculations on biomacromolecules are becoming increasingly explored, aiming to provide better accuracy in the description of protein-ligand interactions and the prediction of binding affinities. In principle, the QM formulation includes all contributions to the energy, accounting for terms usually missing in molecular mechanics force-fields, such as electronic polarization effects, metal coordination, and covalent binding; moreover, QM methods are systematically improvable, and provide a greater degree of transferability. In this mini-review we present recent applications of explicit QM-based methods in small-molecule docking and scoring, and in the calculation of binding free-energy in protein-ligand systems. Although the routine use of QM-based approaches in an industrial drug lead discovery setting remains a formidable challenging task, it is likely they will increasingly become active players within the drug discovery pipeline.

Magnetic properties of alluvial soils contaminated with lead, zinc and cadmium

NASA Astrophysics Data System (ADS)

Petrovský, E.; Kapička, A.; Jordanova, N.; Borůvka, L.

2001-09-01

Several proxy methods have been used recently to outline increased levels of pollution. One of them is based on measurements of the concentration of (ferri)magnetic minerals of anthropogenic origin. This method has been used recently in the mapping of both polluted and unpolluted areas. In order to validate this method, a more detailed study of links between magnetic parameters characterising the physical shape of magnetic minerals and concentrations of heavy metals is needed. In this study, we analysed the magnetic characteristics of alluvial soils, formed as a result of several breakdowns of wet deposit sink of ashes from a lead ore smelter. The soils were previously analysed for concentration of lead, zinc and cadmium. Our results show that in this case of a shared source of heavy metals and magnetic minerals, simple measurements of magnetic susceptibility discriminate well between polluted and clean areas. In addition, the concentration pattern agrees with the concentrations of the heavy metals studied in deeper soil layers that were not affected by post-depositional changes due to climate and remediation efforts.

Shape optimization for aerodynamic efficiency and low observability

NASA Technical Reports Server (NTRS)

Vinh, Hoang; Van Dam, C. P.; Dwyer, Harry A.

1993-01-01

Field methods based on the finite-difference approximations of the time-domain Maxwell's equations and the potential-flow equation have been developed to solve the multidisciplinary problem of airfoil shaping for aerodynamic efficiency and low radar cross section (RCS). A parametric study and an optimization study employing the two analysis methods are presented to illustrate their combined capabilities. The parametric study shows that for frontal radar illumination, the RCS of an airfoil is independent of the chordwise location of maximum thickness but depends strongly on the maximum thickness, leading-edge radius, and leadingedge shape. In addition, this study shows that the RCS of an airfoil can be reduced without significant effects on its transonic aerodynamic efficiency by reducing the leading-edge radius and/or modifying the shape of the leading edge. The optimization study involves the minimization of wave drag for a non-lifting, symmetrical airfoil with constraints on the airfoil maximum thickness and monostatic RCS. This optimization study shows that the two analysis methods can be used effectively to design aerodynamically efficient airfoils with certain desired RCS characteristics.

A Design Problem of Assembly Line Systems using Genetic Algorithm under the BTO Environment

NASA Astrophysics Data System (ADS)

Abe, Kazuaki; Yamada, Tetsuo; Matsui, Masayuki

Under the BTO environment, stochastic assembly lines require design methods which shorten not only the production lead time but also the ready time for the line design. We propose a design method for Assembly Line Systems (ALS) in Yamada et al. (2001) by using Genetic Algorithm (GA) and Adam-Eve GA, in which all design variables are determined in consideration of constraints such as line length related to the production lead time. First, an ALS model with a line length constraint is introduced, and an optimal design problem is set to maximize the net reward under shorter lead time. Next, a simulation optimization method is developed using Adam-Eve GA and traditional GA. Finally, an optimal design example is shown and discussed by comparing the 2-stage design by Yamada et al. (2001) and both the GA designs. It is shown that the Adam-Eve GA is superior to the traditional GA design in terms of computational time though there is only a slight difference in terms of net reward.

NMR approaches in structure-based lead discovery: recent developments and new frontiers for targeting multi-protein complexes.

PubMed

Dias, David M; Ciulli, Alessio

2014-01-01

Nuclear magnetic resonance (NMR) spectroscopy is a pivotal method for structure-based and fragment-based lead discovery because it is one of the most robust techniques to provide information on protein structure, dynamics and interaction at an atomic level in solution. Nowadays, in most ligand screening cascades, NMR-based methods are applied to identify and structurally validate small molecule binding. These can be high-throughput and are often used synergistically with other biophysical assays. Here, we describe current state-of-the-art in the portfolio of available NMR-based experiments that are used to aid early-stage lead discovery. We then focus on multi-protein complexes as targets and how NMR spectroscopy allows studying of interactions within the high molecular weight assemblies that make up a vast fraction of the yet untargeted proteome. Finally, we give our perspective on how currently available methods could build an improved strategy for drug discovery against such challenging targets. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

Comparison of EDTA and SDS as potential surface impregnation agents for lead adsorption by activated carbon

NASA Astrophysics Data System (ADS)

Chen, Wei-fang; Pan, Ling; Chen, Li-fang; Yu, Zhe; Wang, Qiong; Yan, Chang-cheng

2014-08-01

Ethylene diamine tetraacetic acid (EDTA) and sodium dodecyl sulfate (SDS) were employed to impregnate activated carbons for the purpose of lead removal. The mechanisms of surface impregnation and lead adsorption method of chemical regeneration were investigated. Results showed that the highest impregnation of EDTA and SDS on activated carbon was 0.33 and 0.96 mmol/g, respectively. Adsorption capacities for lead of EDTA and SDS impregnated activated carbons reached 0.29 and 0.24 mmol/g. Rapid small scale column tests of adsorption and regeneration were conducted. Lead adsorption was greatly enhanced by EDTA impregnation. In addition, EDTA impregnated adsorbent was able to be successful regenerated by HNO3 and thus reused.

PbS-PbSe IR detector arrays

NASA Technical Reports Server (NTRS)

Barrett, John R. (Inventor)

1986-01-01

A silicon wafer is provided which does not employ individually bonded leads between the IR sensitive elements and the input stages of multiplexers. The wafer is first coated with lead selenide in a first detector array area and is thereafter coated with lead sulfide within a second detector array area. The described steps result in the direct chemical deposition of lead selenide and lead sulfide upon the silicon wafer to eliminate individual wire bonding, bumping, flip chipping, planar interconnecting methods of connecting detector array elements to silicon chip circuitry, e.g., multiplexers, to enable easy fabrication of very long arrays. The electrode structure employed, produces an increase in the electrical field gradient between the electrodes for a given volume of detector material, relative to conventional electrode configurations.

Controllable deposition of regular lead iodide nanoplatelets and their photoluminescence at room temperature

NASA Astrophysics Data System (ADS)

Kong, Weimin; Li, Guohui; Liang, Qiangbing; Ji, Xingqi; Li, Gang; Ji, Ting; Che, Tao; Hao, Yuying; Cui, Yanxia

2018-03-01

In this work, the synthesis of regular single crystalline lead iodide nanoplatelets are carried out based on the physical vapor phase deposition method. Different lead iodide nanoplatelets are obtained by tuning the location of the mica substrate along with the temperature of the tube furnace. The rules of size, thickness, density of the lead iodide nanoplatelets at varied deposition conditions are analyzed according to the crystal growth principles. It was claimed in literature that the photoluminescence of lead iodide could be obtained only at a low temperature (lower than 200 K). Here, at room temperature, we successfully obtained the photoluminescence spectra of the prepared lead iodide nanoplatelets, which possess two apparent peaks due to the biexcitons and the inelastic scattering of excitons, respectively. Our present study contributes to the development of nanoscaled high performance optoelectronic devices.

Hypersonic aerospace vehicle leading edge cooling using heat pipe, transpiration and film cooling techniques

NASA Astrophysics Data System (ADS)

Modlin, James Michael

An investigation was conducted to study the feasibility of cooling hypersonic vehicle leading edge structures exposed to severe aerodynamic surface heat fluxes using a combination of liquid metal heat pipes and surface mass transfer cooling techniques. A generalized, transient, finite difference based hypersonic leading edge cooling model was developed that incorporated these effects and was demonstrated on an assumed aerospace plane-type wing leading edge section and a SCRAMJET engine inlet leading edge section. The hypersonic leading edge cooling model was developed using an existing, experimentally verified heat pipe model. Two applications of the hypersonic leading edge cooling model were examined. An assumed aerospace plane-type wing leading edge section exposed to a severe laminar, hypersonic aerodynamic surface heat flux was studied. A second application of the hypersonic leading edge cooling model was conducted on an assumed one-quarter inch nose diameter SCRAMJET engine inlet leading edge section exposed to both a transient laminar, hypersonic aerodynamic surface heat flux and a type 4 shock interference surface heat flux. The investigation led to the conclusion that cooling leading edge structures exposed to severe hypersonic flight environments using a combination of liquid metal heat pipe, surface transpiration, and film cooling methods appeared feasible.

Nuclear qualified in-containment electrical connectors and methods of connecting electrical conductors

NASA Astrophysics Data System (ADS)

Powell, J. G.

1990-07-01

A nuclear qualified in-containment electrical connection is presented that comprises: (1) an insulated, sheathed instrument lead having electrical conductors extending from one end thereof to provide two exposed lead wires; (2) a watertight cable having electrical conducting wires therein and extending from one end of the cable to provide two lead wires therefrom; (3) two butt splice connectors each connecting the ends of respective ones of the lead wires from the instrument lead and cable; (4) a length of heat shrinkable plastic tubing positioned over each butt splice connector and an adjacent portion of a respective lead wire from the cable and heat shrunk into position; and (5) a length of heat shrinkable plastic tubing on the end portion of the instrument lead adjacent the lead wires therefrom, heat shrunk thereon, with a length of outer heat shrinkable plastic tubing. The plastic tubing extends over the end portion of the instrument lead and the heat shrinkable tubing and over the butt splice connectors and a portion of the cable adjacent the cable lead lines. The outer heat shrinkable tubing is heat shrunk into sealing position on the instrument lead and cable.

Blood Lead Level Among Fuel Station Workers

PubMed Central

Al-Rudainy, Laith Abdulmajeed

2010-01-01

Objectives This study aims to determine the level of lead in blood of fuel station workers and in a group of people not occupationally exposed to lead Methods 53 control subjects with low risk lead exposure and 45 fuel station workers comprising the study group were included in this study in a period from September 2008 to December 2009. Blood samples were collected and analyzed for each subject by Lead Care Blood Testing System. The average blood lead levels of each group were compared using the independent sample (Mann – Whitney U) test. Results The median (range) 14.1 (7.5–56) μg/dl concentration of lead in the blood of fuel stations workers was significantly higher than the median (range) 6.5 (4.0–1.6) μg/dl concentration of lead in the blood of the control group (p< 0.001).The results obtained also showed that the values of blood lead levels in many workers were higher than action and upper limits acceptable for adults. In fuel station workers, the duration of exposure to leaded fuel was significantly correlated with the blood lead level. Conclusions Occupational exposure to lead is prevalent among many fuel station workers in Basrah. A policy action to improve working conditions and to phase out the use of leaded gasoline is recommended. PMID:22043339

Contraceptive Evaluation.

ERIC Educational Resources Information Center

Hulka, Barbara S.; And Others

The objective of research in contraceptive evaluation is to improve the ability of individuals to choose contraceptive methods best suited to their needs and circumstances and to provide information that will lead to the development of safer and more effective methods. There are usually three considerations in judging the importance of a method of…

Students' Reflective Essays as Insights into Student Centred-Pedagogies within the Undergraduate Research Methods Curriculum

ERIC Educational Resources Information Center

Hosein, Anesa; Rao, Namrata

2017-01-01

In higher education, despite the emphasis on student-centred pedagogical approaches, undergraduate research methods pedagogy remains surprisingly teacher-directed. Consequently, it may lead to research methods students assuming that becoming a researcher involves gathering information rather than it being a continuous developmental process. To…

Single Laboratory Comparison of Host-Specific PCR Assays for the Detection of Bovine Fecal Pollution

EPA Science Inventory

There are numerous PCR-based methods available to detect bovine fecal pollution in ambient waters. Each method targets a different gene and microorganism leading to differences in method performance, making it difficult to determine which approach is most suitable for field appl...

Intercultural Sourcebook: Cross-Cultural Training Methods. Volume 2.

ERIC Educational Resources Information Center

Fowler, Sandra M., Ed.; Mumford, Monica G., Ed.

This comprehensive collection of training methods and exercises used by top trainers in the cross-cultural field contains resources essential for cross-cultural learning. This second volume of the collection includes articles by 34 leading cross-cultural trainers and covers new or divergent training methods for cross-cultural skill development and…

Prevalence of Evaluation Method Courses in Education Leader Doctoral Preparation

ERIC Educational Resources Information Center

Shepperson, Tara L.

2013-01-01

This exploratory study investigated the prevalence of single evaluation methods courses in doctoral education leadership programs. Analysis of websites of 132 leading U.S. university programs found 62 evaluation methods courses in 54 programs. Content analysis of 49 course catalog descriptions resulted in five categories: survey, planning and…

Piezoelectric and Electrostrictive Materials for Transducer Applications. Volume 3.

DTIC Science & Technology

1988-03-01

the preparation and characterization of these required compositions. High-purity lead acetate, titanium isopropoxide , and zirconium n-propoxide were...method was similar to the procedure used in Reference 4 to prepare PbTiO 3. High-purity lead acetate [Pb(C2 H3 0 2 )2 -3H-2Oj, titanium isopropoxide [Ti(OC...dielectric constant as shown in Figure 14(A). P.𔃿 8 IV. CONCLUSION High-purity lead acetate, titanium isopropoxide and zirconium n-propoxide were used as

Study of influence of various factors on electrochemical signal of lead in water solutions

NASA Astrophysics Data System (ADS)

Zhikharev, Yu N.; Andrianova, L. I.; Ogudova, E. V.

2018-05-01

The conditions for obtaining a reproducible signal of lead in water solutions of indifferent electrolytes on various substrates (working electrodes) for analytical purposes were studied. Attention was also paid to studying the regularities of the initial stage of formation of lead sediments by the method of inversion voltammetry. The possibility of using different working electrodes to obtain stable current-potential curves is shown depending on the conditions of electrolysis, pH of the medium, the electrolysis potential and impurities.

Ultrafast time-resolved spectroscopy of lead halide perovskite films

NASA Astrophysics Data System (ADS)

Idowu, Mopelola A.; Yau, Sung H.; Varnavski, Oleg; Goodson, Theodore

2015-09-01

Recently, lead halide perovskites which are organic-inorganic hybrid structures, have been discovered to be highly efficient as light absorbers. Herein, we show the investigation of the excited state dynamics and emission properties of non-stoichiometric precursor formed lead halide perovskites grown by interdiffusion method using steady-state and time-resolved spectroscopic measurements. The influence of the different ratios of the non-stoichiometric precursor solution was examined. The observed photoluminescence properties were correlated with the femtosecond transient absorption measurements.

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

1998-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

2000-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead environmentally safe projectiles and method of making same

DOEpatents

Lowden, Richard A.; McCoig, Thomas M.; Dooley, Joseph B.

1999-01-01

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic base material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics.

Non-lead, environmentally safe projectiles and method of making same

DOEpatents

Lowden, R.A.; McCoig, T.M.; Dooley, J.B.

1998-06-02

A projectile, such as a bullet, is made by combining two different metals in proportions calculated to achieve a desired density, without using lead. A base constituent, made of a material having density greater than lead, is combined with a binder constituent having less density. The binder constituent is malleable and ductile metallic phase material that forms projectile shapes when subjected to a consolidation force, such as compression. The metal constituents can be selected, rationed, and consolidated to achieve desired frangibility characteristics. 7 figs.

How can we deal with ANN in flood forecasting? As a simulation model or updating kernel!

NASA Astrophysics Data System (ADS)

Hassan Saddagh, Mohammad; Javad Abedini, Mohammad

2010-05-01

Flood forecasting and early warning, as a non-structural measure for flood control, is often considered to be the most effective and suitable alternative to mitigate the damage and human loss caused by flood. Forecast results which are output of hydrologic, hydraulic and/or black box models should secure accuracy of flood values and timing, especially for long lead time. The application of the artificial neural network (ANN) in flood forecasting has received extensive attentions in recent years due to its capability to capture the dynamics inherent in complex processes including flood. However, results obtained from executing plain ANN as simulation model demonstrate dramatic reduction in performance indices as lead time increases. This paper is intended to monitor the performance indices as it relates to flood forecasting and early warning using two different methodologies. While the first method employs a multilayer neural network trained using back-propagation scheme to forecast output hydrograph of a hypothetical river for various forecast lead time up to 6.0 hr, the second method uses 1D hydrodynamic MIKE11 model as forecasting model and multilayer neural network as updating kernel to monitor and assess the performance indices compared to ANN alone in light of increase in lead time. Results presented in both graphical and tabular format indicate superiority of MIKE11 coupled with ANN as updating kernel compared to ANN as simulation model alone. While plain ANN produces more accurate results for short lead time, the errors increase expeditiously for longer lead time. The second methodology provides more accurate and reliable results for longer forecast lead time.

Childhood lead poisoning in a Somali refugee resettlement community in New Hampshire.

PubMed

Caron, Rosemary M; Tshabangu-Soko, Thandi; Finefrock, Krysten

2013-08-01

Despite the gradual decrease in childhood lead poisoning in the United States, the risk for lead poisoning among African refugee children who resettle in the United States remains elevated. Communication methods implemented by resettlement agencies in the public health system for preventing childhood lead poisoning in this at-risk population warrant further investigation. We utilized structured interviews with key stakeholders (resettlement agencies, social service agencies developed by African refugees and resettled Somali refugees) involved in the refugee resettlement process to (1) describe the agency's role in the refugee resettlement process; (2) examine communication methods utilized and barriers experienced by the public health system in reference to childhood lead poisoning; (3) describe the refugee population's perception of childhood lead poisoning; (4) examine general challenges experienced by the public health system and the refugee population during the resettlement process; and (5) describe stakeholders' recommendations to improve health communication efforts. Based on our findings, we propose that communities are important determinants in health-related problems for refugee populations. Each community has its own environment and public health system that interacts with each other to influence health risks and risk perceptions of its populations. We advocate that understanding a community's ecology and implementing a culture-centered approach is essential for the public health system to help educate and prevent communication inequalities and health disparities among an at-risk African refugee population. This action can reduce a population's resistance to communication and help build a community's capacity to address a persistent public health problem, such as childhood lead poisoning.

Universal algorithm for diagnosis of biventricular capture in patients with cardiac resynchronization therapy.

PubMed

Jastrzebski, Marek; Kukla, Piotr; Fijorek, Kamil; Czarnecka, Danuta

2014-08-01

An accurate and universal method for diagnosis of biventricular (BiV) capture using a standard 12-lead electrocardiogram (ECG) would be useful for assessment of cardiac resynchronization therapy (CRT) patients. Our objective was to develop and validate such an ECG method for BiV capture diagnosis that would be independent of pacing lead positions-a major confounder that significantly influences the morphologies of paced QRS complexes. On the basis of an evaluation of 789 ECGs of 443 patients with heart failure and various right ventricular (RV) and left ventricular (LV) lead positions, the following algorithm was constructed and validated. BiV capture was diagnosed if the QRS in lead I was predominantly negative and either V1 QRS was predominantly positive or V6 QRS was of negative onset and predominantly negative (step 1), or if QRS complex duration was <160 ms (step 2). All other ECGs were classified as loss of LV capture. The algorithm showed good accuracy (93%), sensitivity (97%), and specificity (90%) for detection of loss of LV capture. The performance of the algorithm did not differ among apical, midseptal, and outflow tract RV lead positions and various LV lead positions. LV capture leaves diagnostic hallmarks in the fused BiV QRS related to different vectors of depolarization and more rapid depolarization of the ventricles. An accurate two-step ECG algorithm for BiV capture diagnosis was developed and validated. This algorithm is universally applicable to all CRT patients, regardless of the positions of the pacing leads. ©2014 Wiley Periodicals, Inc.

Application of flowerlike MgO for highly sensitive determination of lead via matrix-assisted laser desorption/ionization mass spectrometry.

PubMed

Hou, Jian; Chen, Suming; Cao, Changyan; Liu, Huihui; Xiong, Caiqiao; Zhang, Ning; He, Qing; Song, Weiguo; Nie, Zongxiu

2016-08-01

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI MS) is a high-throughput method to achieve fast and accurate identification of lead (Pb) exposure, but is seldom used because of low ionization efficiency and insufficient sensitivity. Nanomaterials applied in MS are a promising technique to overcome the obstacles of MALDI. Flowerlike MgO nanostructures are applied for highly sensitive lead profiling in real samples. They can be used in two ways: (a) MgO is mixed with N-naphthylethylenediamine dihydrochloride (NEDC) as a novel matrix MgO/NEDC; (b) MgO is applied as an absorbent to enrich Pb ions in very dilute solution. The signal intensities of lead by MgO/NEDC were ten times higher than the NEDC matrix. It also shows superior anti-interference ability when analyzing 10 μmol/L Pb ions in the presence of organic substances or interfering metal ions. By applying MgO as adsorbent, the LOD of lead before enrichment is 1 nmol/L. Blood lead test can be achieved using this enrichment process. Besides, MgO can play the role of internal standard to achieve quantitative analysis. Flowerlike MgO nanostructures were applied for highly sensitive lead profiling in real samples. The method is helpful to prevent Pb contamination in a wide range. Further, the combination of MgO with MALDI MS could inspire more nanomaterials being applied in highly sensitive profiling of pollutants. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

The effect of L-ascorbic acid and/or tocopherol supplementation on electrophysiological parameters of the colon of rats chronically exposed to lead

PubMed Central

Kosik-Bogacka, Danuta I.; Baranowska-Bosiacka, Irena; Marchlewicz, Mariola; Kolasa, Agnieszka; Jakubowska, Katarzyna; Olszewska, Maria; Łanocha, Natalia; Wiernicki, Ireneusz; Millo, Barbara; Wiszniewska, Barbara; Chlubek, Dariusz

2011-01-01

Summary Background The aim of this study was to assess the effect of diet supplementation with L-ascorbic acid (500 mg/L), tocopherol (3 mg/kg b.w.), and/or a water soluble analog of tocopherol (Trolox) (48 mg/L) on ion transport in the colon of rats subjected to a chronic exposure (9 months) to 0.1% lead acetate in drinking water. Material/Methods The electrophysiological parameters of the colon wall were measured with Ussing methods. Lead content in the whole blood was analyzed by graphite furnace atomic absorption spectrometry (GFAAS) using Zeeman correction. L-ascorbic acid and tocopherol in plasma was measured by high performance liquid chromatography. Immunohistochemical reaction was carried out for visualization of occludin, the intracellular tight junction protein. Results We showed a strong inhibitory effect of lead on the electrophysiological parameters, changes in intestinal permeability, disappearance of junctional occludin, decreased amount of mucus covering the colon surface, and the accumulation of PAS-positive substance in the apical region of the cytoplasm in the absorptive cells. Conclusions Supplementation with tocopherol or Trolox did not exert a beneficial influence on the studied parameters. L-ascorbic acid positively influenced the examined electrophysiological parameters, as it cancelled the inhibitory influence of lead on ion transport in the rat colon. L-ascorbic acid also protected against tight junction disruption of epithelial cells in the colon of the lead-treated rats. A similar effect was observed in the group of rats receiving lead and supplemented with L-ascorbic acid plus Trolox. PMID:21169903

Analysis of heavy metal lead (Pb) levels with Aas in cow's milk by giving cumin (Cuminum cyminum L.), white turmeric (Curcuma zedoaria Rosc.) and mango turmeric (Curcuma mangga Val.).

PubMed

Nurdin, E; Putra, D P; Amelia, T

2013-11-01

The aim of this study was to determine the effect of giving Cumin (Cuminum cyminum L.), White Turmeric (Curcuma zedoaria Rosc.) and Mango Turmeric (Curcuma mango Val.) on levels of heavy metals lead (Pb) in cow's milk produced. The study was conducted in West Java with experimental method in 16 Fries Holland dairy cows with lactation period of 2-4 months and lactation months of 3-4 months. The design used is simple randomized design with 4 treatments such as Group A (control/no treatment), Group B (Cumin 0.03% body weight), Group C (White Turmeric 0.02% body weight) and Group D (Mango Turmeric 0.06% body weight). Measurement of Pb levels in milk using the method of wet destruction, while Pb measurements on faeces using wet ashing method, by means of Atomic Absorption Spectrophotometry. Based on the researsch results showed that administration of Cumin, White Turmeric and Mango Turmeric have very real effect on reducing levels of heavy metals lead (Pb) in cow's milk produced, with a consecutive decrease 98.36, 99.33 and 99.37% and the very real effect on elevated levels of Pb in faeces by 68.01, 64.52 and 80.54%. Mango Turmeric is the best treatment of three treatment in decreasing lead level in milk.

Effects of lead structure in Bering Sea pack ice on the flight costs of wintering spectacled eiders

NASA Astrophysics Data System (ADS)

Bump, Joseph K.; Lovvorn, James R.

2004-10-01

In polar regions, sea ice is critical habitat for many marine birds and mammals. The quality of pack ice habitat depends on the duration and spacing of leads (openings in the ice), which determine access to water and air for diving endotherms, and how often and how far they must move as leads open and close. Recent warming trends have caused major changes in the extent and nature of sea ice at large scales used in climate models. However, no studies have analyzed lead structure in terms of habitat for ice-dependent endotherms, or effects of climate on ice habitat at scales relevant to their daily movements. Based on observations from an icebreaker and synthetic aperture radar (SAR) images, we developed methods to describe the dynamics and thermodynamics of lead structure relative to use by spectacled eiders ( Somateria fischeri) wintering in pack ice of the Bering Sea. By correlating lead structure with weather variables, we then used these methods to estimate changes in lead dynamics from 1945 to 2002, and effects of such changes on flight costs of the eiders. For 1991-1992, when images were available about every 3 days throughout winter, SAR images were divided among five weather regimes defined by wind speed, wind direction, and air temperature. Based on 12.5-m pixels, lead shape, compass orientation, and fetch across leads did not differ among the weather regimes. However, the five regimes differed in total area of open water, leads per unit area, and distance between leads. Lead duration was modeled based on air temperature, wind, and fetch. Estimates of mean daily flight time for eiders, based on lead duration and distance between neighboring leads, differed among regimes by 0 to 15 min. Resulting flight costs varied from 0 to 158 kJ day -1, or from 0% to 11% of estimated field metabolic rate. Over 57 winters (1945-2002), variation among years in mean daily flight time was most influenced by the north-south wind component, which determined pack divergence (lead opening) during northerly winds or pack convergence (lead closing) during southerly winds. Mean daily flight time and flight cost during winter did not differ among proposed periods of decadal-scale climate shifts in the North Pacific Ocean. Although leads in mobile pack ice constantly open and close with variations in wind, under most conditions in the Bering Sea there appeared to be a shifting-mosaic steady-state of lead availability. Long-term trends in the extent and timing of Bering Sea pack ice may have affected spectacled eiders more by altering foodweb processes than by changing flight costs relative to lead structure.

Adjustment of QT dispersion assessed from 12 lead electrocardiograms for different numbers of analysed electrocardiographic leads: comparison of stability of different methods.

PubMed Central

Hnatkova, K; Malik, M; Kautzner, J; Gang, Y; Camm, A J

1994-01-01

OBJECTIVE--Normal electrocardiographic recordings were analysed to establish the influence of measurement of different numbers of electrocardiographic leads on the results of different formulas expressing QT dispersion and the effects of adjustment of QT dispersion obtained from a subset of an electrocardiogram to approximate to the true QT dispersion obtained from a complete electrocardiogram. SUBJECTS AND METHODS--Resting 12 lead electrocardiograms of 27 healthy people were investigated. In each lead, the QT interval was measured with a digitising board and QT dispersion was evaluated by three formulas: (A) the difference between the longest and the shortest QT interval among all leads; (B) the difference between the second longest and the second shortest QT interval; (C) SD of QT intervals in different leads. For each formula, the "true" dispersion was assessed from all measurable leads and then different combinations of leads were omitted. The mean relative differences between the QT dispersion with a given number of omitted leads and the "true" QT dispersion (mean relative errors) and the coefficients of variance of the results of QT dispersion obtained when omitting combinations of leads were compared for the different formulas. The procedure was repeated with an adjustment of each formula dividing its results by the square root of the number of measured leads. The same approach was used for the measurement of QT dispersion from the chest leads including a fourth formula (D) the SD of interlead differences weighted according to the distances between leads. For different formulas, the mean relative errors caused by omitting individual electrocardiographic leads were also assessed and the importance of individual leads for correct measurement of QT dispersion was investigated. RESULTS--The study found important differences between different formulas for assessment of QT dispersion with respect to compensation for missing measurements of QT interval. The standard max-min formula (A) performed poorly (mean relative errors of 6.1% to 18.5% for missing one to four leads) but was appropriately adjusted with the factor of 1/square root of n (n = number of measured leads). In a population of healthy people such an adjustment removed the systematic bias introduced by missing leads of the 12 lead electrocardiogram and significantly reduced the mean relative errors caused by the omission of several leads. The unadjusted SD was the optimum formula (C) for the analysis of 12 lead electrocardiograms, and the weighted standard deviation (D) was the optimum for the analysis of six lead chest electrocardiograms. The coefficients of variance of measurements of QT dispersion with different missing leads were very large (about 3 to 7 for one to four missing leads). Independently of the formula for measurement of QT dispersion, omission of different leads produced substantially different relative errors. In 12 lead electrocardiograms the largest relative errors (> 10%) were caused by omitting lead aVL or lead V1. CONCLUSIONS--Because of the large coefficients of variance, the concept of adjusting the QT dispersion for different numbers of electrocardiographic leads used in its assessment is difficult if not impossible to fulfil. Thus it is likely to be more appropriate to assess QT dispersion from standardised constant sets of electrocardiographic leads. PMID:7833200

Studying Practices of Leading--Qualitative Shadowing in Early Childhood Research

ERIC Educational Resources Information Center

Hognestad, Karin; Bøe, Marit

2016-01-01

This article considers qualitative shadowing as a fruitful method to investigate leadership practices. We propose that an approach to practice that takes into account the activities of "sayings, doings and relatings" offers a fresh perspective on how to obtain rich data on practices of leading. The value of this idea is illustrated from…

Teacher Openness and Prosocial Motivation: Creating an Environment Where Questions Lead to Engaged Students

ERIC Educational Resources Information Center

Crane, Bret D.

2017-01-01

Evidence suggests that student engagement in the classroom leads to improved learning outcomes. As a result, teachers of management have promoted ways to involve students through Socratic teaching methods, case-based pedagogy, and class discussion. These approaches to learning emphasize the use of questions to stimulate student engagement.…

INTERLABORATORY COMPARISON OF MASS SPECTROMETRIC METHODS FOR LEAD ISOTOPES AND TRACE ELEMENTS IN NIST SRM 1400 BONE ASH

EPA Science Inventory

The results of an interlaboratory comparison are reported for he lead isotope composition and for trace element concentrations in NIST SRM 1400 Bone Ash obtained using quadrupole and magnetic-sector inductively coupled plasma mass spectrometry (ICP-MS) and (for the Pb isotopes on...

In Vitro And In Vivo Approaches For The Measurement Of Oral Bioavailability Of Lead (Pb) In Contaminated Soils: A Review

EPA Science Inventory

We reviewed the published evidence of lead (Pb) contamination of urban soils, soil Pb risk to children through hand-to-mouth activity, reduction of soil Pb bioavailability due to soil amendments, and methods to assess bioaccessibility which correlate with bioavailability of soil ...

Leading Higher Education Professionals: Local, Connected, and Artful

ERIC Educational Resources Information Center

Bathurst, Ralph; van Gelderen, Marco

2014-01-01

In this paper, we explore the work life of a scholar new to academia in her methods of leading informally. We discuss five vignettes that offer moments of learning and reflection, including reducing performance anxiety, privileging financial accountability, the rise of the virtual world, the impact of silence, and the potential for confrontation…

The Determination of Lead in Gasoline by Atomic Absorption Spectrometry.

ERIC Educational Resources Information Center

Coleman, M. F. M.

1985-01-01

Describes an experiment that involves the extraction of lead from gasoline into an aqueous solvent using iodine monochloride reagent. This method (which avoids the aspiration of organic solvents) also illustrates the use of wavelengths other than the most sensitive wavelength and effects of flame stoichiometry and burner height upon absorbance.…

77 FR 65146 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-25

... and retard mode, in case of go-around, might lead to a temporary loss of airplane longitudinal control... comments by any of the following methods: Federal eRulemaking Portal: Go to http://www.regulations.gov... flare and retard mode, in case of go-around, the situation may lead to a temporary loss of aeroplane...

Analysis of KC-46 Live-Fire Risk Mitigation Program Testing

DTIC Science & Technology

2012-03-01

the use of real hardware such as electrohydraulic actuators , electrical units, and converter regulators (Andrus, 2010). The only feasible method for...worked with the MQ-9 as a test engineer and analyst for the programs IOT &E, RQ-4 as lead engineer and program lead for the block 3 and the block 4

Solar Energy Evolution and Diffusion Studies: 2014-2016 | Solar Research |

Science.gov Websites

motivations for adoption A non-adopter considerer survey that targeted lost leads by installers to identify two experimental market pilots to test methods to increase lead generation and conversion using concerned individuals may need to emphasize non-environmental benefits. The results also support leveraging

Double-Polymer-Modified Pencil Lead for Stripping Voltammetry of Perchlorate in Drinking Water

ERIC Educational Resources Information Center

Izadyar, Anahita; Kim, Yushin; Ward, Michelle M.; Amemiya, Shigeru

2012-01-01

The inexpensive and disposable electrode based on a double-polymer-modified pencil lead is proposed for upper-division undergraduate instrumental laboratories to enable the highly sensitive detection of perchlorate. Students fabricate and utilize their own electrodes in the 3-4 h laboratory session to learn important concepts and methods of…

Healthy Behaviors and Lifestyles in Young Adults with a History of Developmental Disabilities

ERIC Educational Resources Information Center

Rurangirwa, Jacqueline; Braun, Kim Van Naarden; Schendel, Diana; Yeargin-Allsopp, Marshalyn

2006-01-01

Objective: Measure select Healthy People 2010 Leading Health Indicators in young adults with and without a history of developmental disabilities (DD) using a population-based cohort. Methods: Young adults were interviewed to assess the prevalence of seven Leading Health Indicators: physical activity, overweight and obesity, tobacco use, substance…