Science.gov

Sample records for left-handed transmission lines

  1. Mid-infrared metasurface made of composite right/left-handed transmission-line

    NASA Astrophysics Data System (ADS)

    Luo, Yi; Ying, Xiangxiao; Pu, Yang; Jiang, Yadong; Xu, Jimmy; Liu, Zhijun

    2016-06-01

    We report on the realization of a mid-infrared metasurface based on the concept of composite right/left-handed transmission-line. The metasurface consists of a three-layer metal-insulator-metal structure patterned into transmission-lines by electron-beam lithography. Angle-variable reflection spectroscopy measurements reveal resonant absorption features corresponding to both right- and left-handed propagations in the leaky-wave guided mode region. Material loss is shown to dominate the quality factor of the left-handed modes, while the radiative loss dominates the right-handed ones. The experimental results are in good agreement with full-wave numerical simulations and are explained with an equivalent circuit model.

  2. Novel Composite Right/Left-Handed Metamaterial-Based Leaky-Wave Transmission-Lines

    NASA Astrophysics Data System (ADS)

    Hashemi, Mohammed Reza Mahmoodi

    The focus of this dissertation is on the design procedure as well as analysis of a very interesting category of metamaterial-based structures namely composite right/left-handed (CRLH) Leaky-wave (LW) transmission-lines (TL). As a result several unique CRLH-TLs are designed and presented. Each of the discussed CRLH LW-TLs has exceptional and beneficial characteristics, which is only realizable due to their composite right/left-handed nature and dispersion characteristics. The operation mechanism of CRLH-TL is explained in the first chapter by the overview of the theory behind the CRLH concept. The dispersion diagram of a CRLH unit-cell shows that the phase constant (beta) is a non-linear function of frequency with a beta = 0 point at a non-zero frequency. Furthermore, a CRLH-TL supports left-handed slow-wave (guided-wave) and fast-wave (leaky-wave) modes, where the phase velocity and the group velocity are anti-parallel and phase advanced is achievable, as well as right-handed slow-wave and fast-wave modes, where the two velocities are parallel and phase delay can be observed. The subject of the second chapter is conformal CRLH LW-TLs. The effect of conformation of a planar uniform CRLH LW-TL on a convex and a concave surface are investigated. It is shown when the CRLH LW-TL is operating in the fast-wave region the conformation affects its radiation characteristics and the radiation pattern becomes wider in both convex and concave cases. A dispersion engineering method is introduced to modify the conformal structure such that it provides comparable performance to that of the planar version in terms of radiation characteristics. Then taking advantage of the proposed modification method a multifunctional electronically controlled conformal CRLH LW-TL is introduced in a later part of this chapter. Varactor diodes are introduced in the unit-cells to electronically control its guided and radiation characteristics. This CRLH-TL has the ability to operate partially in the

  3. A compact very wideband amplifying filter based on RTD loaded composite right/left-handed transmission lines.

    PubMed

    Abu-Marasa, Mahmoud O Mahmoud; El-Khozondar, Hala Jarallah

    2015-01-01

    The composite right/left-handed (CRLH) transmission line (TL) is presented as a general TL possessing both left-handed (LH) and right-handed (RH) natures. RH materials have both positive permittivity and positive permeability, and LH materials have both negative permittivity and negative permeability. This paper aims to design and analyze nonlinear CRLH-TL transmission line loaded with resonant tunneling diode (RTD). The main application of this design is a very wideband and compact filter that amplifies the travelling signal. We used OrCAD and ADS software to analyze the proposed circuit. CRLH-TL consists of a microstrip line which is loaded with complementary split-rings resonators (CSRRs), series gaps, and shunt inductor connected parallel to the RTD. The designed structure possess a wide band that ranges from 5 to 10.5 GHz and amplifies signal up to 50 %. The proposed design is of interest to microwave compact component designers. PMID:26636021

  4. A compact very wideband amplifying filter based on RTD loaded composite right/left-handed transmission lines.

    PubMed

    Abu-Marasa, Mahmoud O Mahmoud; El-Khozondar, Hala Jarallah

    2015-01-01

    The composite right/left-handed (CRLH) transmission line (TL) is presented as a general TL possessing both left-handed (LH) and right-handed (RH) natures. RH materials have both positive permittivity and positive permeability, and LH materials have both negative permittivity and negative permeability. This paper aims to design and analyze nonlinear CRLH-TL transmission line loaded with resonant tunneling diode (RTD). The main application of this design is a very wideband and compact filter that amplifies the travelling signal. We used OrCAD and ADS software to analyze the proposed circuit. CRLH-TL consists of a microstrip line which is loaded with complementary split-rings resonators (CSRRs), series gaps, and shunt inductor connected parallel to the RTD. The designed structure possess a wide band that ranges from 5 to 10.5 GHz and amplifies signal up to 50 %. The proposed design is of interest to microwave compact component designers.

  5. Leaky wave antenna with amplitude controlled beam steering based on composite right/left-handed transmission lines

    NASA Astrophysics Data System (ADS)

    Eberspächer, M. A.; Eibert, T. F.

    2010-09-01

    An antenna comprising two different composite right/left-handed transmission line structures is proposed which enables easy beam steering at an operation frequency of 10 GHz. The composite right/left-handed transmission lines are based on planar, periodically arranged via free unit cells, implemented in microstrip technology. Both transmission lines exhibit the infinite wavelength phenomenon which occurs at 9.72 GHz and 9.89 GHz, respectively. Thus, operating the different leaky wave structures at 10 GHz, radiation with azimuth angles of ±8° and ±17° can be achieved depending on the selected input port. In order to obtain a tunable main beam direction, the radiation patterns of both structures are superimposed by feeding them simultaneously. The influence of each guiding structure, and hence the direction of the main beam, can be controlled via the feeding amplitude. As a result of this, the beam can be steered between ±17° with a gain of up to 10 dBi. The guiding structures are arranged in parallel with a clearance of a=12.2 mm which is less than half of the wavelength in free space. This allows in a further step the attachment of additional guiding structures in order to increase the tunable angle range or creating an antenna array with a small beamwidth in the elevation plane without the occurrence of grating lobes. An antenna prototype was fabricated and validated by measurements.

  6. MEMS-tunable composite right/left-handed (CRLH) transmission line and its application to a phase shifter

    NASA Astrophysics Data System (ADS)

    Hwang, Sung-Hyun; Jang, Taehee; Kim, Jong-Man; Kim, Yong-Kweon; Lim, Sungjoon; Baek, Chang-Wook

    2011-12-01

    This paper reports a novel compact tunable composite right/left-handed transmission line (CRLH TL) with multi-state phase tunability using integrated microelectromechanical system (MEMS) switches and its application to a phase shifter. It is possible to select multiple states with different positive/negative phase responses. The phase states can be determined by controlling the admittance of capacitors and impedance of inductors through MEMS switch operations. The designed devices are analyzed using electromagnetic and circuit simulations. The propagation characteristics and phase lead/lag properties of the devices are investigated. The designed device can be operated as a 90°/-90° phase tunable CRLH TL at 8 GHz and a four-state phase shifter at 9.5 GHz by switch configuration. At 8 GHz, the phase responses of the device were 87° of the phase lead and -80° of the phase lag for the left-handed (LH) and right-handed (RH) states, respectively. At 9.5 GHz, the phase of each state varies among 26.7°, 14.6°, -6.7°, and -11.5°, where the first two states are in the LH region and the others are in the RH region. At 9-15 GHz, insertion losses are measured to be <2.6 dB, and return losses are >10 dB.

  7. Coupled backward- and forward-propagating solitons in a composite right- and left-handed transmission line.

    PubMed

    Veldes, G P; Cuevas, J; Kevrekidis, P G; Frantzeskakis, D J

    2013-07-01

    We study the coupling between backward- and forward-propagating wave modes, with the same group velocity, in a composite right- and left-handed nonlinear transmission line. Using an asymptotic multiscale expansion technique, we derive a system of two coupled nonlinear Schrödinger equations governing the evolution of the envelopes of these modes. We show that this system supports a variety of backward- and forward-propagating vector solitons of the bright-bright, bright-dark, and dark-bright type. Performing systematic numerical simulations in the framework of the original lattice that models the transmission line, we study the propagation properties of the derived vector soliton solutions. We show that all types of the predicted solitons exist, but differ on their robustness: Only bright-bright solitons propagate undistorted for long times, while the other types are less robust, featuring shorter lifetimes. In all cases, our analytical predictions are in very good agreement with the results of the simulations, at least up to times of the order of the solitons' lifetimes.

  8. Resonance amplification of left-handed transmission at optical frequencies by stimulated emission of radiation in active metamaterials.

    PubMed

    Dong, Zheng-Gao; Liu, Hui; Li, Tao; Zhu, Zhi-Hong; Wang, Shu-Ming; Cao, Jing-Xiao; Zhu, Shi-Ning; Zhang, X

    2008-12-01

    We demonstrate that left-handed resonance transmission from metallic metamaterial, composed of periodically arranged double rings, can be extended to visible spectrum by introducing an active medium layer as the substrate. The severe ohmic loss inside metals at optical frequencies is compensated by stimulated emission of radiation in this active system. Due to the resonance amplification mechanism of recently proposed lasing spaser, the left-handed transmission band can be restored up to 610 nm wavelength, in dependence on the gain coefficient of the active layer. Additionally, threshold gains for different scaling levels of the double-ring unit are investigated to evaluate the gain requirement of left-handed transmission restoration at different frequency ranges.

  9. Left-handed-media simulation and transmission of EM waves in subwavelength split-ring-resonator-loaded metallic waveguides.

    PubMed

    Marqués, R; Martel, J; Mesa, F; Medina, F

    2002-10-28

    At microwave frequencies, hollow metallic waveguides behave in certain aspects as a "one-dimensional plasma." This feature will be advantageously used for simulating the propagation of electromagnetic (EM) waves in left-handed metamaterials provided the hollow waveguide is periodically loaded with split ring resonators. It will be shown that EM transmission in this structure is feasible within a certain frequency band even if the transverse dimensions of the waveguide are much smaller than the associated free-space wavelength. This effect can be qualitatively and quantitatively explained by the left-handed metamaterial theory, thus providing a new experimental validation for such a theory.

  10. [Left-handed painters].

    PubMed

    Lanthony, P

    1995-03-01

    The role of the right hemisphere in the building of our visual space is now well established. The purpose of the present research was to determine the proportion of left handed painters, and to identify famous painters which were left-handed. The methods were as follows. First, the study of the portraits of the painters; but self-portraits were worthless (right-handed painters often painting themself as observed in the mirror, i.e. left-handed). Therefore, only portraits of painters made by another painter or by photography were used. Secondly, the orientation of the hatchings used by the artist for the representation of the shadows in the drawing: the right-handed artist making hatchings descending from right to left, and the left-handed artist making hatchings descending from left to right. Thirdly, the study of the relevant literature about history of art. The studied population included 500 painters divided in two groups: a population of 127 painters studied by portraits and hatchings; and a population of 373 painters studied only by hatchings. In the first population, the proportion of left-handed painters was 4.7%. In the second population, the proportion of left-handed painters was 2.1%. Among the 500 painters they were 14 left-handed subjects, i.e. 2.8%. These 14 painters were, in alphabetical order: Cambiaso, Dufy, Escher, Füssli, Grandville, Holbein, Klee, De La Patellière, Léonard de Vinci, Menzel, Montelupo, Papety, Regnault, Van Goyen.(ABSTRACT TRUNCATED AT 250 WORDS)

  11. The Left-Handed Writer.

    ERIC Educational Resources Information Center

    Bloodsworth, James Gaston

    Contrary to the beliefs of many, right-handedness is not a single factor existing in almost all people, with a few exceptions termed left-handed: neither extreme exists independently of the other. During the first 4 years of life there is a period of fluctuation between right and left-handed dominance. Statistics and findings vary in determining…

  12. Why Am I Left-Handed?

    MedlinePlus

    ... does since most hitters are right-handed. In basketball and other sports, a left-handed player can ... change in strategy. For instance, a left-handed basketball player will dribble with his or her left ...

  13. Slow microwaves in left-handed materials

    NASA Astrophysics Data System (ADS)

    di Gennaro, E.; Parimi, P. V.; Lu, W. T.; Sridhar, S.; Derov, J. S.; Turchinetz, B.

    2005-07-01

    Remarkably slow propagation of microwaves in two different classes of left-handed materials (LHM’s) is reported from microwave-pulse and continuous-wave transmission measurements. Microwave dispersion in a composite LHM made of split-ring resonators and wire strips reveals group velocity vg˜c/50 , where c is the free-space light velocity. Photonic crystals (PhC’s) made of dielectric Al2O3 rods reveal vg˜c/10 . Group delay dispersion of both the composite LHM and PhC’s determined from the experiment is in complete agreement with that obtained from theory. The slow group velocities are quantitatively described by the strong dispersion observed in these materials.

  14. Multimode circuit quantum electrodynamics with hybrid metamaterial transmission lines.

    PubMed

    Egger, D J; Wilhelm, F K

    2013-10-18

    Quantum transmission lines are central to superconducting and hybrid quantum computing. In this work we show how coupling them to a left-handed transmission line allows circuit QED to reach a new regime: multimode ultrastrong coupling. Out of the many potential applications of this novel device, we discuss the preparation of multipartite entangled states and the simulation of the spin-boson model where a quantum phase transition is reached up to finite size effects.

  15. Left-handed Children in Singapore.

    ERIC Educational Resources Information Center

    Gan, Linda

    1998-01-01

    Used teacher questionnaires to examine incidence of left-handedness in nearly 2,800 Singaporean children, racial differences in this left-handed population, and educational provisions in preschool and primary school. Findings indicated that 7.5% of preschoolers and 6.3% of primary children were left-handed, with a higher proportion being Chinese…

  16. The Left-Handed: "Their Sinister" History.

    ERIC Educational Resources Information Center

    Costas, Elaine Fowler

    The history of left-handedness can provide teachers and parents a better understanding of left-handed children and give those children more pride in their difference. No child should be made to feel that he or she is abnormal because of using the left hand, although some specific instruction for these students is necessary in handwriting. Many…

  17. Active terahertz quantum-cascade composite right/left-handed metamaterial

    NASA Astrophysics Data System (ADS)

    Tavallaee, Amir A.; Hon, Philip W. C.; Chen, Qi-Sheng; Itoh, Tatsuo; Williams, Benjamin S.

    2013-01-01

    We report the demonstration of a composite right/left-handed (CRLH) metamaterial waveguide for terahertz quantum-cascade (QC) lasers. By incorporating gap capacitors (˜250 nm) in the top metallization of a metal-metal waveguide operating in a higher order lateral mode, we have realized a CRLH transmission line that supports traveling modes with negative effective phase indices (i.e., left-handed or backward-wave propagation). The CRLH metamaterial waveguide is employed as an active leaky-wave antenna for a terahertz QC-laser. Directional single-lobed beams launched in the backwards direction at angles of -4° and -63° were experimentally observed at excitation frequencies 2.59 and 2.48 THz, respectively.

  18. Quasidiscrete microwave solitons in a split-ring-resonator-based left-handed coplanar waveguide.

    PubMed

    Veldes, G P; Cuevas, J; Kevrekidis, P G; Frantzeskakis, D J

    2011-04-01

    We study the propagation of quasidiscrete microwave solitons in a nonlinear left-handed coplanar waveguide coupled with split-ring resonators. By considering the relevant transmission line analog, we derive a nonlinear lattice model which is studied analytically by means of a quasidiscrete approximation. We derive a nonlinear Schrödinger equation, and find that the system supports bright envelope soliton solutions in a relatively wide subinterval of the left-handed frequency band. We perform systematic numerical simulations, in the framework of the nonlinear lattice model, to study the propagation properties of the quasidiscrete microwave solitons. Our numerical findings are in good agreement with the analytical predictions, and suggest that the predicted structures are quite robust and may be observed in experiments.

  19. Left-handed wrestlers are more successful.

    PubMed

    Ziyagil, Mehmet Akif; Gursoy, Recep; Dane, Senol; Yuksel, Ramazan

    2010-08-01

    It has been reported that there is a high proportion of left-handers among top athletes in different sports. In this study, the goal was to examine the rate of left-handedness in the top wrestlers at the world championships for achievement by left-handed wrestlers. The rate of left-handedness was higher in wrestlers with medal honors compared to wrestlers without medals for both men and women. The winning numbers and match degrees were higher in the left-handed wrestlers than in both right- and mixed-handed wrestlers among top international wrestlers.

  20. Numerical Modeling of Left-Handed Metamaterials

    SciTech Connect

    Burke, G J; Champagne, N J; Sharpe, R M

    2001-11-06

    The EIGER method of moments program with periodic Green's function was used to model a periodic array of strips and split-ring resonators. Left-handed propagation due to negative index of refraction is demonstrated in a frequency band. The effective material parameters versus frequency are extracted from the EIGER solution.

  1. Artificial, parallel, left-handed DNA helices.

    PubMed

    Tian, Cheng; Zhang, Chuan; Li, Xiang; Li, Yingmei; Wang, Guansong; Mao, Chengde

    2012-12-19

    This communication reports an engineered DNA architecture. It contains multiple domains of half-turn-long, standard B-DNA duplexes. While each helical domain is right-handed and its two component strands are antiparallel, the global architecture is left-handed and the two component DNA strands are oriented parallel to each other.

  2. Series Transmission Line Transformer

    DOEpatents

    Buckles, Robert A.; Booth, Rex; Yen, Boris T.

    2004-06-29

    A series transmission line transformer is set forth which includes two or more of impedance matched sets of at least two transmissions lines such as shielded cables, connected in parallel at one end ans series at the other in a cascading fashion. The cables are wound about a magnetic core. The series transmission line transformer (STLT) which can provide for higher impedance ratios and bandwidths, which is scalable, and which is of simpler design and construction.

  3. Transmission Line Security Monitor

    SciTech Connect

    2011-01-01

    The Transmission Line Security Monitor is a multi-sensor monitor that mounts directly on high-voltage transmission lines to detect, characterize and communicate terrorist activity, human tampering and threatening conditions around support towers. For more information about INL's critical infrastructure protection research, visit http://www.facebook.com/idahonationallaboratory.

  4. Transmission Line Security Monitor

    ScienceCinema

    None

    2016-07-12

    The Transmission Line Security Monitor is a multi-sensor monitor that mounts directly on high-voltage transmission lines to detect, characterize and communicate terrorist activity, human tampering and threatening conditions around support towers. For more information about INL's critical infrastructure protection research, visit http://www.facebook.com/idahonationallaboratory.

  5. Photonic-resonant left-handed medium

    NASA Astrophysics Data System (ADS)

    Shen, Jian Qi

    2006-08-01

    A new scheme to realize simultaneously negative permittivity and permeability in a coherent atomic vapor medium (photonic-resonant material) via a coherent driving mechanism is suggested. It is verified that the atomic system coherently driven by a strong optical field will give rise to a negative refractive index in certain probe frequency ranges. One of the most remarkable features of the present scheme is such that a slab fabricated by the left-handed vapor medium is an ideal candidate for designing perfect lenses since the photonic-resonant atomic vapor cannot only exhibit an isotropic negative refractive index, but also provide a good impedance match at the air-medium interfaces.

  6. Spatial Deficit in Familial Left-Handed Children.

    ERIC Educational Resources Information Center

    And Others; Eme, Robert

    1978-01-01

    The study evaluated the hypothesis that familial left-handed children, who presumably have bilateral representation of language ability, should show an impairment in spatial abiblity on 44 children (22 right handed, 11 familial left handed, and 11 nonfamilial left handed) whose average age was 8 years old. (Author/PHR)

  7. Study of left-handed materials

    NASA Astrophysics Data System (ADS)

    Zhou, Jiangfeng

    Left handed materials (LHMs) are artificial materials that have negative electrical permittivity, negative magnetic permeability, and negative index of refraction across a common frequency band. They possess electromagnetic (EM) properties not found in nature. LHMs have attracted tremendous attention because of their potential applications to build the perfect lens and cloaking devices. In the past few years there has been ample proof for the existence of LHMs in the microwave frequency range. Recently, researchers are trying hard to push the operating frequency of LHMs into terahertz and the optical regime. In this thesis, we start with the theoretical prediction of left handed materials made by Veselago 40 years ago, introducing the unique electromagnetic properties of the left handed materials. After discussing the realization of LHMs by the split ring resonators (SRRs) and wire designs, we briefly review the development of LHMs from microwave frequency to the optical regime. We discuss the chiral metamaterial, which provides an alternative approach to realize negative refractive index. In Chapter 2, we discuss the electromagnetic properties of the SRRs and the breakdown of linear scaling properties of SRRs at infrared and optical frequencies. By discussing the current modes, and the electric and magnetic moments, we study three resonance modes of SRR with respect to different polarizations of EM waves. Through numerical simulations, we find the breakdown of linear scaling, due to the free electron kinetic energy for frequencies above 100 THz. This result is important. It proves that researchers cannot push metamaterials into the optical regime by just scaling down the geometrical size of metamaterial designs used at low frequency. Due to the breakdown of the linear scaling property, a much smaller structure size of LHMs design is required in the optical regime, so new designs with simpler topology are needed. In Chapter 3, we discuss a short wire pair design

  8. Printed circuit dispersive transmission line

    DOEpatents

    Ikezi, H.; Lin-Liu, Y.R.; DeGrassie, J.S.

    1991-08-27

    A printed circuit dispersive transmission line structure is disclosed comprising an insulator, a ground plane formed on one surface of the insulator, a first transmission line formed on a second surface of the insulator, and a second transmission line also formed on the second surface of the insulator and of longer length than the first transmission line and periodically intersecting the first transmission line. In a preferred embodiment, the transmission line structure exhibits highly dispersive characteristics by designing the length of one of the transmission line between two adjacent periodic intersections to be longer than the other. 5 figures.

  9. Printed circuit dispersive transmission line

    DOEpatents

    Ikezi, Hiroyuki; Lin-Liu, Yuh-Ren; DeGrassie, John S.

    1991-01-01

    A printed circuit dispersive transmission line structure is disclosed comprising an insulator, a ground plane formed on one surface of the insulator, a first transmission line formed on a second surface of the insulator, and a second transmission line also formed on the second surface of the insulator and of longer length than the first transmission line and periodically intersecting the first transmission line. In a preferred embodiment, the transmission line structure exhibits highly dispersive characteristics by designing the length of one of the transmission line between two adjacent periodic intersections to be longer than the other.

  10. Left-handed metamaterial coatings for subwavelength-resolution imaging.

    PubMed

    Zapata-Rodríguez, Carlos J; Pastor, David; Martínez, Luis E; Miret, Juan J

    2012-09-01

    We report on a procedure to improve the resolution of far-field imaging by using a neighboring high-index medium that is coated with a left-handed metamaterial. The resulting plot can also exhibit an enhanced transmission by considering proper conditions to retract backscattering. Based on negative refraction, geometrical aberrations are considered in detail since they may cause a great impact in this sort of diffraction-unlimited imaging by reducing its resolution power. We employ a standard aberration analysis to refine the asymmetric configuration of metamaterial superlenses. We demonstrate that low-order centrosymmetric aberrations can be fully corrected for a given object plane. For subwavelength-resolution imaging, however, high-order aberrations become of relevance, which may be balanced with defocus. Not only the point spread function but also numerical simulations based on the finite-element method support our theoretical analysis, and subwavelength resolution is verified in the image plane.

  11. Topology optimization of multilayer left-handed material based on the genetic algorithm

    NASA Astrophysics Data System (ADS)

    Xu, Weikai; Wang, Wei

    2013-02-01

    Owing to the special properties, left-handed materials (LHM) have important potential applications in engineering. However, in the current stage, the design of LHM is primarily based on several basic prototypes such as meta-material and transmission line structures. In the present work, the topology optimization technology is introduced to design a type of multilayer LHM. A type of one-dimensional material with periodic unit cell is studied and the topology of its microstructure is designed by using the technology of enumerative search and genetic algorithm (GA), respectively. The material is composed of metal and ferrite films, and several types of negative refraction materials are obtained numerically. These obtained materials with periodic unit cells can exhibit negative refractive index in some frequency spectrums, and the results show that the GA could achieve good designs efficiently in a larger design space.

  12. Drill string transmission line

    DOEpatents

    Hall, David R.; Hall, Jr., H. Tracy; Pixton, David S.; Bradford, Kline; Fox, Joe

    2006-03-28

    A transmission line assembly for transmitting information along a downhole tool comprising a pin end, a box end, and a central bore traveling between the pin end and the box end, is disclosed in one embodiment of the invention as including a protective conduit. A transmission line is routed through the protective conduit. The protective conduit is routed through the central bore and the ends of the protective conduit are routed through channels formed in the pin end and box end of the downhole tool. The protective conduit is elastically forced into a spiral or other non-linear path along the interior surface of the central bore by compressing the protective conduit to a length within the downhole tool shorter than the protective conduit.

  13. Electron-Beam Instability in Left-Handed Media

    SciTech Connect

    Bliokh, Yury P. |; Savelev, Sergey; Nori, Franco

    2008-06-20

    We predict that two electron beams can develop an instability when passing through a slab of left-handed media (LHM). This instability, which is inherent only for LHM, originates from the backward Cherenkov radiation and results in a self-modulation of the beams and radiation of electromagnetic waves. These waves leave the sample via the rear surface of the slab (the beam injection plane) and form two shifted bright circles centered at the beams. A simulated spectrum of radiation has well-separated lines on top of a broad continuous spectrum, which indicates dynamical chaos in the system. The radiation intensity and its spectrum can be controlled either by the beams' current or by the distance between the two beams.

  14. Left-Handed Students: A Forgotten Minority. Fastback 399.

    ERIC Educational Resources Information Center

    Kelly, Evelyn B.

    This fastback, a booklet bound "left-handed," is designed to help educators become aware of the problems faced by left-handed students in school and to suggest ways that many of the problems might be solved. Following an introduction discussing a personal experience with left-handedness, the booklet continues with a brief history of the treatment…

  15. Left-Handed Preschool Children with Orthopedic Disabilities.

    ERIC Educational Resources Information Center

    Banham, Katharine M.

    1983-01-01

    The mental development of 332 preschool-age children with orthopedic disabilities was assessed at a children's hospital over a 10-year period, and comparisons were made for right-handed and left-handed. The left-handed children were slower than right-handed children in learning speech and language skills (Author/SEW)

  16. Enantioselective targeting left-handed Z-G-quadruplex.

    PubMed

    Zhao, Andong; Zhao, Chuanqi; Ren, Jinsong; Qu, Xiaogang

    2016-01-25

    Herein, we report the first example where an M-enantiomer of a chiral metal complex can selectively stabilize a left-handed G-quadruplex, but its P-enantiomer cannot. The interactions between the chiral metal complexes and the left-handed G-quadruplex were evaluated by UV melting, circular dichroism, isothermal titration calorimetry, gel electrophoresis and NMR titrations.

  17. Left-Handed Children--Are They Losing Out?

    ERIC Educational Resources Information Center

    Milsom, Lauren

    1995-01-01

    Discusses difficulties faced by left-handed children in everyday schoolwork. Highlights include right-handed bias of toys, clothing, and tools; the need for guidance in handwriting; problem areas including domestic science, arts and crafts, and metal and woodwork; left-hand advantages in sports and creative arts; and the European Left-Handers Club…

  18. A Quantitative Transmission Line Experiment

    ERIC Educational Resources Information Center

    Johnston, D. C.; Silbernagel, B. G.

    1969-01-01

    Describes modifications of a commercially available strip-type transmission line, which makes possible reproducible measurements of standing waves on the line. Experimental data yield values for the characteristic impedance, phase velocity and line wavelength of radiation in the transmission line, and the dielectric constant of material in the…

  19. Hemispheric asymmetries of visual ERPs in left-handed bilinguals.

    PubMed

    Andreou, G; Karapetsas, A

    2001-10-01

    ERPs (N1, P1, N2, P2) obtained from left and right occipital and temporal lobes were elicited in 30 left-handed highly proficient bilingual males in response to visually presented linguistic stimuli. The absence of statistically significant(P = < or =0.05) differences between left and right occipital and temporal lobes in all the components of the waveforms obtained, indicates a bilateral pattern of lateralization in left-handed males for both their native and foreign language.

  20. Left-handed surgical instruments - a guide for cardiac surgeons.

    PubMed

    Burdett, Clare; Theakston, Maureen; Dunning, Joel; Goodwin, Andrew; Kendall, Simon William Henry

    2016-08-19

    For ease of use and to aid precision, left-handed instruments are invaluable to the left-handed surgeon. Although they exist, they are not available in many surgical centres. As a result, most operating theatre staff (including many left-handers) have little knowledge of their value or even application. With specific reference to cardiac surgery, this article addresses the ways in which they differ, why they are needed and what is required - with tips on use.

  1. EC Transmission Line Materials

    SciTech Connect

    Bigelow, Tim S

    2012-05-01

    The purpose of this document is to identify materials acceptable for use in the US ITER Project Office (USIPO)-supplied components for the ITER Electron cyclotron Heating and Current Drive (ECH&CD) transmission lines (TL), PBS-52. The source of material property information for design analysis shall be either the applicable structural code or the ITER Material Properties Handbook. In the case of conflict, the ITER Material Properties Handbook shall take precedence. Materials selection, and use, shall follow the guidelines established in the Materials Assessment Report (MAR). Materials exposed to vacuum shall conform to the ITER Vacuum Handbook. [Ref. 2] Commercial materials shall conform to the applicable standard (e.g., ASTM, JIS, DIN) for the definition of their grade, physical, chemical and electrical properties and related testing. All materials for which a suitable certification from the supplier is not available shall be tested to determine the relevant properties, as part of the procurement. A complete traceability of all the materials including welding materials shall be provided. Halogenated materials (example: insulating materials) shall be forbidden in areas served by the detritiation systems. Exceptions must be approved by the Tritium System and Safety Section Responsible Officers.

  2. Simultaneous normal and parallel incidence planar left-handed metamaterial.

    PubMed

    Lv, Jianhong; Yan, Baorong; Liu, Minghai; Hu, Xiwei

    2009-08-01

    We investigate numerically the negative refraction of a simultaneous normal and parallel incidence planar left-handed metamaterial (LHM) in this paper. This LHM is comprised of fourfold C-shaped rings, which are printed on both sides of the substrates symmetrically, and it can exhibit left-handed properties with electromagnetic wave incident in three different directions. The retrieved result and the simulated result verify the left-handed properties of the fourfold C-shaped metamaterial very well. Then the different electric responses of the normal and parallel incidence cases to the incident electromagnetic wave are discussed, and it is due to the different distribution of the induced currents in the metallic wires.

  3. Electrical transmission line diametrical retainer

    DOEpatents

    Hall, David R.; Hall, Jr., H. Tracy; Pixton, David; Dahlgren, Scott; Sneddon, Cameron; Briscoe, Michael; Fox, Joe

    2004-12-14

    The invention is a mechanism for retaining an electrical transmission line. In one embodiment of the invention it is a system for retaining an electrical transmission line within down hole components. In accordance with one aspect of the invention, the system includes a plurality of downhole components, such as sections of pipe in a drill string. The system also includes a coaxial cable running between the first and second end of a drill pipe, the coaxial cable having a conductive tube and a conductive core within it. The invention allows the electrical transmission line to with stand the tension and compression of drill pipe during routine drilling cycles.

  4. Left-Handed Interfaces for Electromagnetic Surface Waves

    NASA Astrophysics Data System (ADS)

    Kats, A. V.; Savel'Ev, Sergey; Yampol'Skii, V. A.; Nori, Franco

    2007-02-01

    We show that surface electromagnetic waves (SEMWs) propagating along two-dimensional (2D) interfaces separating different metamaterials can behave analogously to 3D electromagnetic waves in either usual or left-handed media, depending on the permeabilities and/or permittivities of the two materials forming the interface. We derive the conditions when SEMWs carry energy opposite to the phase velocity. In analogy to three-dimensional (3D) left-handed media, we derive both an anomalous Cherenkov emission and a reversed Doppler effect. We also predict a negative refraction at the boundary between two different interfaces, which can be useful for perfect 2D lensing.

  5. Crab scars reveal survival advantage of left-handed snails.

    PubMed

    Dietl, Gregory P; Hendricks, Jonathan R

    2006-09-22

    Biological asymmetries are important elements of the structure and function of many living organisms. Using the Plio-Pleistocene fossil record of crab predation on morphologically similar pairs of right- and left-handed snail species, we show here for the first time, contrary to traditional wisdom, that rare left-handed coiling promotes survival from attacks by right-handed crabs. This frequency-dependent result influences the balance of selection processes that maintain left-handedness at the species level and parallels some social interactions in human cultures, such as sports that involve dual contests between opponents of opposite handedness.

  6. Crab scars reveal survival advantage of left-handed snails

    PubMed Central

    Dietl, Gregory P; Hendricks, Jonathan R

    2006-01-01

    Biological asymmetries are important elements of the structure and function of many living organisms. Using the Plio–Pleistocene fossil record of crab predation on morphologically similar pairs of right- and left-handed snail species, we show here for the first time, contrary to traditional wisdom, that rare left-handed coiling promotes survival from attacks by right-handed crabs. This frequency-dependent result influences the balance of selection processes that maintain left-handedness at the species level and parallels some social interactions in human cultures, such as sports that involve dual contests between opponents of opposite handedness. PMID:17148425

  7. Magnetotunable left-handed FeSiB ferromagnetic microwires.

    PubMed

    Labrador, Alberto; Gómez-Polo, Cristina; Pérez-Landazábal, José Ignacio; Zablotskii, Vitalii; Ederra, Iñigo; Gonzalo, Ramón; Badini-Confalonieri, Giovanni; Vázquez, Manuel

    2010-07-01

    The magnetotunable left-handed characteristics of Fe(77.5)Si(12.5)B(10) glass-coated ferromagnetic microwires are analyzed in array and single microwire configuration, employing a rectangular waveguide working in X band. While the negative permeability is ascribed to the natural ferromagnetic resonance (NFMR) of the highly and positive magnetostrictive microwire, the negative permittivity features of the medium are attributed to the interaction of the microwires with the metallic rectangular waveguide. The dependence of the NFMR frequency on the applied external magnetic field enables the design of magnetotunable left-handed systems with wide-frequency band.

  8. Brain Activation Associated with Practiced Left Hand Mirror Writing

    ERIC Educational Resources Information Center

    Kushnir, T.; Arzouan, Y.; Karni, A.; Manor, D.

    2013-01-01

    Mirror writing occurs in healthy children, in various pathologies and occasionally in healthy adults. There are only scant experimental data on the underlying brain processes. Eight, right-handed, healthy young adults were scanned (BOLD-fMRI) before and after practicing left-hand mirror-writing (lh-MW) over seven sessions. They wrote dictated…

  9. The Left Hand of Math and Verbal Talent.

    ERIC Educational Resources Information Center

    Bower, B.

    1985-01-01

    Children possessing extremely high levels of mathematical or verbal ability tend, many times more than normal ability children, to be left-handed (2 times), nearsighted (4 times), and suffering from allergies (2 times). Studies at Johns Hopkins University indicate 80 percent of "precocious" 12-13 year olds have at least one of these…

  10. Left handed dispersion of a stack of subwavelength hole metal arrays at terahertz frequencies

    NASA Astrophysics Data System (ADS)

    Croënne, Charles; Garet, Frédéric; Lheurette, Éric; Coutaz, Jean-Louis; Lippens, Didier

    2009-03-01

    We report on the electromagnetic response of a stack of subwavelength hole metal arrays. The samples were designed for exhibiting left handed dispersion branches under normal incidence, and their transmissivities were optimized via the fabrication of elliptical-shaped holes. They are constituted of benzocyclobutene layers with tens of micron thicknesses and submicron-thick gold films patterned by photolithography. Experimental evidence, achieved by time-domain terahertz spectroscopy and supported by full wave simulations, of a ground left handed dispersion branch is found around 0.45 THz. The insertion losses are -3 dB for a five-layer structure, this good level being explained by the matching of the impedance.

  11. Bilayer fractal structure with multiband left-handed characteristics.

    PubMed

    Du, Qiujiao; Liu, Jinsong; Yang, Hongwu; Yi, Xunong

    2011-08-20

    We present a bilayer fractal structure for the realization of multiband left-handed metamaterial at terahertz frequencies. The structure is composed of metallic H-fractal pairs separated by a dielectric layer. The electromagnetic properties of periodic H-fractal pairs have been investigated by numerical simulation. The period in the propagation direction is extremely small as compared to the wavelength at the operational frequency. Under the electromagnetic wave normal incidence, the material exhibits negative refraction simultaneously around the frequencies of 0.10 and 0.15 THz for parallel polarization, and around the frequencies of 0.19 and 0.38 THz for perpendicular polarization. The design provides a left-handed metamaterial suitable for multiband and compact devices at terahertz frequencies.

  12. Atypical interhemispheric communication in left-handed individuals.

    PubMed

    Iwabuchi, Sarina J; Kirk, Ian J

    2009-01-28

    The relative latencies of evoked electroencephalogram potentials to lateralized visual stimuli were used to calculate the interhemispheric transfer time (IHTT) in right-handed and left-handed males. We confirmed earlier observations of a directional asymmetry in right-handed males. That is, IHTT from the right to the left hemisphere is significantly shorter than from the left to the right. We showed for the first time, however, that this directional asymmetry is not seen in left-handed males. It is suggested that differences in the cytoarchitechtonics of the right and left hemisphere (differences that may result in lateralization of function per se) underlie the asymmetric IHTT in right handers, and that these differences are less pronounced in left handers.

  13. Scatterer localization using a left-handed medium.

    PubMed

    Karkashadze, David; Fernández, Juan Pablo; Shubitidze, Fridon

    2009-06-01

    This paper explores the possibility of using the focusing property of left-handed materials to estimate the location of a visually obscured target. The field scattered by the target and measured on a surface can be considered as incident upon a left-handed half-space and should converge to a point resembling the mirror image of the scatterer's location. The results are obtained using the method of auxiliary sources as adapted to double-negative media. Two-dimensional scattering is considered, either from a single object or from several targets, using pointlike and Gaussian sources of illumination. The method gives reasonable results when the sizes of the scatterers are comparable to the wavelength.

  14. Proprioceptive target matching asymmetries in left-handed individuals.

    PubMed

    Goble, Daniel J; Noble, Brittany C; Brown, Susan H

    2009-08-01

    In right-handers, the ability to reproduce proprioceptive targets has been shown to be asymmetric, favoring the non-preferred left arm. The present study sought to determine whether a similar arm/hemisphere asymmetry exists for left-handers. Ten strong left-handed adults used the left or right arm to perform proprioceptive target matching tasks that varied in processing demands (i.e., need for memory, interhemispheric transfer) and target amplitude (20, 40 degrees). Similar to right-handers, left-handed individuals had smaller total errors when matching with the non-preferred arm. This asymmetry was greatest in conditions with increased processing demands and larger amplitude targets. These results provide the first evidence to date of right arm/left hemisphere dominance for proprioceptive target matching in left-handers that is the "mirror image" of right-handers.

  15. Left-Handed W bosons at the LHC

    SciTech Connect

    Bern, Z.; Diana, G.; Dixon, L.J.; Cordero, F.Febres; Forde, D.; Gleisberg, T.; Hoeche, S.; Ita, H.; Kosower, D.A.; Maitre, D.; Ozeren, K.; /UCLA

    2011-05-20

    The production of W bosons in association with jets is an important background to new physics at the LHC. Events in which the W carries large transverse momentum and decays leptonically lead to large missing energy and are of particular importance. We show that the left-handed nature of the W coupling, combined with valence quark domination at a pp machine, leads to a large left-handed polarization for both W{sup +} and W{sup -} bosons at large transverse momenta. The polarization fractions are very stable with respect to QCD corrections. The leptonic decay of the W{sup +-} bosons translates the common left-handed polarization into a strong asymmetry in transverse momentum distributions between positrons and electrons, and between neutrinos and anti-neutrinos (missing transverse energy). Such asymmetries may provide an effective experimental handle on separating W +jets from top quark production, which exhibits very little asymmetry due to C invariance, and from various types of new physics.

  16. Microwave pulse propagation measurements in left-handed materials

    NASA Astrophysics Data System (ADS)

    di Gennaro, Emiliano; Parimi, Patanjali V.; Vodo, Plarenta; Lu, Wentao; Sridhar, Srinivas

    2004-03-01

    Left handed electromagnetism is well established in media with negative permeability and permittivity and in photonic crystals [1]. In such media the negative refractive index is accompanied by large dispersion dn/dω, and consequently a very low group velocity is predicted for left-handed metamaterial (LHM). It is well known that an artificial material consisting of interleaved arrays of wires and split ring resonators in a certain microwave frequency range shows left handed behavior. We have carried out pulse measurements on LHM using a transition analyzer in order to measure the group velocity. Time delay measurements are performed in an X-band and parallel plate waveguide. Sending a 100ns width pulse with a carrier frequency ranging between 9 and 11 GHz, we analyze the signal delay due to the sample. The results suggest that the group velocity in the LHM is very low. Pulse delay measurements in photonic crystals are also discussed. Work supported by NSF & AFRL [1]. P. V. Parimi et al., submitted (2003).

  17. Nonceramic insulators for transmission lines

    SciTech Connect

    Schneider, H.M. . High Voltage Transmission Research Center); Hall, J.F. ); Karady, G. ); Rendowden, J. )

    1989-10-01

    Progress in development of nonceramic transmission lines insulator technology is reviewed. The results of a survey to utilities in the United States are presented to indicate the range of applications, distribution by voltage class, appraisal of performance, and failure modes. Concerns expressed by utility representatives at a recent workshop are described and future research and standardization needs are presented.

  18. Pulse shaping with transmission lines

    DOEpatents

    Wilcox, R.B.

    1985-08-15

    A method and apparatus for forming shaped voltage pulses uses passive reflection from a transmission line with nonuniform impedance. The impedance of the reflecting line varies with length in accordance with the desired pulse shape. A high voltage input pulse is transmitted to the reflecting line. A reflected pulse is produced having the desired shape and is transmitted by pulse removal means to a load. Light activated photoconductive switches made of silicon can be utilized. The pulse shaper can be used to drive a Pockels cell to produce shaped optical pulses.

  19. Pulse shaping with transmission lines

    DOEpatents

    Wilcox, Russell B.

    1987-01-01

    A method and apparatus for forming shaped voltage pulses uses passive reflection from a transmission line with nonuniform impedance. The impedance of the reflecting line varies with length in accordance with the desired pulse shape. A high voltage input pulse is transmitted to the reflecting line. A reflected pulse is produced having the desired shape and is transmitted by pulse removal means to a load. Light activated photoconductive switches made of silicon can be utilized. The pulse shaper can be used to drive a Pockels cell to produce shaped optical pulses.

  20. Coiled transmission line pulse generators

    DOEpatents

    McDonald, Kenneth Fox

    2010-11-09

    Methods and apparatus are provided for fabricating and constructing solid dielectric "Coiled Transmission Line" pulse generators in radial or axial coiled geometries. The pour and cure fabrication process enables a wide variety of geometries and form factors. The volume between the conductors is filled with liquid blends of monomers, polymers, oligomers, and/or cross-linkers and dielectric powders; and then cured to form high field strength and high dielectric constant solid dielectric transmission lines that intrinsically produce ideal rectangular high voltage pulses when charged and switched into matched impedance loads. Voltage levels may be increased by Marx and/or Blumlein principles incorporating spark gap or, preferentially, solid state switches (such as optically triggered thyristors) which produce reliable, high repetition rate operation. Moreover, these Marxed pulse generators can be DC charged and do not require additional pulse forming circuitry, pulse forming lines, transformers, or an a high voltage spark gap output switch. The apparatus accommodates a wide range of voltages, impedances, pulse durations, pulse repetition rates, and duty cycles. The resulting mobile or flight platform friendly cylindrical geometric configuration is much more compact, light-weight, and robust than conventional linear geometries, or pulse generators constructed from conventional components. Installing additional circuitry may accommodate optional pulse shape improvements. The Coiled Transmission Lines can also be connected in parallel to decrease the impedance, or in series to increase the pulse length.

  1. Frequency Bandwidth Optimization of Left-Handed Metamaterial

    NASA Technical Reports Server (NTRS)

    Chevalier, Christine T.; Wilson, Jeffrey D.

    2004-01-01

    Recently, left-handed metamaterials (LHM s) have been demonstrated with an effective negative index of refraction and with antiparallel group and phase velocities for microwave radiation over a narrow frequency bandwidth. In order to take advantage of these characteristics for practical applications, it will be beneficial to develop LHM s with increased frequency bandwidth response and lower losses. In this paper a commercial three-dimensional electromagnetic simulation code is used to explore the effects of geometry parameter variations on the frequency bandwidth of a LHM at microwave frequencies. Utilizing an optimizing routine in the code, a geometry was generated with a bandwidth more than twice as large as the original geometry.

  2. Phase compensating effect in left-handed materials

    NASA Astrophysics Data System (ADS)

    Feng, Liang; Liu, Xiao-Ping; Lu, Ming-Hui; Chen, Yan-Feng

    2004-11-01

    Based on the difference between negative refraction and negative refractive index, the phase compensating effect was proposed to distinguish negative refraction in left-handed materials (LHMs) and photonic crystals (PCs). With this effect, perfect lens (PL) of LHM in which both propagating and evanescent waves contribute to the image could be well understood, which is differed from superlens made of PCs. Furthermore, a 1D periodic structure consisted of ordinary materials and LHMs was predicted to realize higher and wider bandgaps than the 1D conventional photonic crystal due to phase compensating effect.

  3. Controllable optical black hole in left-handed materials.

    PubMed

    Bai, Qiang; Chen, Jing; Shen, Nian-Hai; Cheng, Chen; Wang, Hui-Tian

    2010-02-01

    Halting and storing light by infinitely decelerating its speed, in the absence of any form of external control, is extremely di+/-cult to imagine. Here we present a theoretical prediction of a controllable optical black hole composed of a planar left-handed material slab. We reveal a criterion that the effective round-trip propagation length in one zigzag path is zero, which brings light to a complete standstill. Both theory and ab initio simulation demonstrate that this optical black hole has degrees flexible controllability for the speed of light. Surprisingly, the ab initio simulations reveal that our scheme has degrees flexible controllability for swallowing, holding, and releasing light. PMID:20174039

  4. Structure of a left-handed DNA G-quadruplex.

    PubMed

    Chung, Wan Jun; Heddi, Brahim; Schmitt, Emmanuelle; Lim, Kah Wai; Mechulam, Yves; Phan, Anh Tuân

    2015-03-01

    Aside from the well-known double helix, DNA can also adopt an alternative four-stranded structure known as G-quadruplex. Implications of such a structure in cellular processes, as well as its therapeutic and diagnostic applications, have been reported. The G-quadruplex structure is highly polymorphic, but so far, only right-handed helical forms have been observed. Here we present the NMR solution and X-ray crystal structures of a left-handed DNA G-quadruplex. The structure displays unprecedented features that can be exploited as unique recognition elements.

  5. Garner-Interference in left-handed awkward grasping.

    PubMed

    Eloka, Owino; Feuerhake, Felix; Janczyk, Markus; Franz, Volker H

    2015-07-01

    The Perception-Action Model (PAM) claims to provide a coherent interpretation of data from all areas of the visual neurosciences, most notably data from neuropsychological patients and from behavioral experiments in healthy people. Here, we tested two claims that are part of the core version of the PAM: (a) certain actions (natural, highly practiced, and right-handed) are controlled by the dorsal vision for action pathway, while other actions (awkward, unpracticed, or left-handed) are controlled by the ventral vision for perception pathway. (b) Only the dorsal pathway operates in an analytical fashion, being able to selectively focus on the task-relevant dimension of an object (Ganel and Goodale, Nature 426(6967):664-667, 2003). We show that one of these claims must be wrong: using the same test for analytical processing as Ganel and Goodale (2003), we found that even an action that should clearly be ventral (left-handed awkward grasping) shows analytical processing just as a dorsal task does (right-handed natural precision grasping). These results are at odds with the PAM and point to an inconsistency of the model.

  6. Left-handed sperm removal by male Calopteryx damselflies (Odonata).

    PubMed

    Tsuchiya, Kaori; Hayashi, Fumio

    2014-01-01

    Male genitalia in several insect species are asymmetry in right and left shape. However, the function of such asymmetric male genitalia is still unclear. We found that the male genitalia of the damselfly Calopteryx cornelia (Odonata: Calopterygidae) are morphologically symmetric just after emergence but asymmetric after reproductive maturation. Males remove rival sperm stored in the female bursa copulatrix (single spherical sac) and the following spermatheca (Y-shaped tubular sac) prior to their own ejaculation to prevent sperm competition. Males possess the aedeagus with a recurved head to remove bursal sperm and a pair of spiny lateral processes to remove spermathecal sperm. The right lateral process is less developed than the left, and sperm stored in the right spermathecal tube are rarely removed. Experiments involving surgical cutting of each lateral process demonstrated that only the left process functions in spermathecal sperm removal. Thus, males of C. cornelia are left-handed in their sperm removal behaviour at copulation.

  7. Terahertz Quantum-Cascade Transmission-Line Metamaterials

    NASA Astrophysics Data System (ADS)

    Tavallaee, Amir Ali

    was demonstrated from terahertz QC-lasers with leaky-wave coupler antennas which exhibited slope efficiencies ˜ 4 times greater than conventional Fabry-Perot metal-metal waveguides. Using this technique the first demonstration of beam scanning for a terahertz QC-laser was reported (from 35° - 60°) as the emission frequency varied from 2.65 - 2.81 THz. Towards the bigger goal of realizing an active terahertz metamaterial to ultimately develop "zero-index" terahertz quantum-cascade lasers immune to spatial hole burning, or "negative-index" metamaterials for superresolution terahertz imaging, a composite right-/left-handed transmission-line metamaterial based upon subwavelength metal waveguide loaded with terahertz QC material was demonstrated. Due to the addition of distributed series capacitors (realized by introducing gaps in top metallization) and shunt inductors (realized by operating in the higher-order lateral mode of the waveguide), the transmission-line metamaterial exhibits left-handed (backward waves or negative index) leaky-wave propagation from 2.3 - 2.45 THz in addition to the conventional right-handed leaky-wave behavior (from 2.6 - 3.0 THz).

  8. Superconducting transmission line particle detector

    DOEpatents

    Gray, K.E.

    1988-07-28

    A microvertex particle detector for use in a high energy physic collider including a plurality of parallel superconducting thin film strips separated from a superconducting ground plane by an insulating layer to form a plurality of superconducting waveguides. The microvertex particle detector indicates passage of a charged subatomic particle by measuring a voltage pulse measured across a superconducting waveguide caused by the transition of the superconducting thin film strip from a superconducting to a non- superconducting state in response to the passage of a charged particle. A plurality of superconducting thin film strips in two orthogonal planes plus the slow electromagnetic wave propagating in a superconducting transmission line are used to resolve N/sup 2/ ambiguity of charged particle events. 6 figs.

  9. Superconducting transmission line particle detector

    DOEpatents

    Gray, Kenneth E.

    1989-01-01

    A microvertex particle detector for use in a high energy physic collider including a plurality of parallel superconducting thin film strips separated from a superconducting ground plane by an insulating layer to form a plurality of superconducting waveguides. The microvertex particle detector indicates passage of a charged subatomic particle by measuring a voltage pulse measured across a superconducting waveguide caused by the transition of the superconducting thin film strip from a superconducting to a non-superconducting state in response to the passage of a charged particle. A plurality of superconducting thin film strips in two orthogonal planes plus the slow electromagnetic wave propogating in a superconducting transmission line are used to resolve N.sup.2 ambiguity of charged particle events.

  10. Magnetically insulated transmission line oscillator

    DOEpatents

    Bacon, L.D.; Ballard, W.P.; Clark, M.C.; Marder, B.M.

    1987-05-19

    A magnetically insulated transmission line oscillator employs self-generated magnetic fields to generate microwave energy. An anode of the oscillator includes slow-wave structures which are formed of a plurality of thin conductive vanes defining cavities therebetween, and a gap is formed between the anode and a cathode of the oscillator. In response to a pulsed voltage applied to the anode and cathode, self-generated magnetic fields are produced in a cross-field orientation with respect to the orientation of the electric field between the anode and the cathode. The cross-field magnetic fields insulate the flow of electrons in the gap and confine the flow of electrons within the gap. 11 figs.

  11. Magnetically insulated transmission line oscillator

    DOEpatents

    Bacon, Larry D.; Ballard, William P.; Clark, M. Collins; Marder, Barry M.

    1988-01-01

    A magnetically insulated transmission line oscillator employs self-generated magnetic fields to generate microwave energy. An anode of the oscillator includes slow-wave structures which are formed of a plurality of thin conductive vanes defining cavities therebetween, and a gap is formed between the anode and a cathode of the oscillator. In response to a pulsed voltage applied to the anode and cathode, self-generated magnetic fields arfe produced in a cross-field orientation with respect to the orientation of the electric field between the anode and the cathode. The cross-field magnetic fields insulate the flow of electrons in the gap and confine the flow of electrons within the gap.

  12. Flat Lens Focusing Demonstrated With Left-Handed Metamaterial

    NASA Technical Reports Server (NTRS)

    Wilson, Jeffrey D.; Schwartz, Zachary D.; Chevalier, Christine T.; Downey, Alan N.; Vaden, Karl R.

    2004-01-01

    Left-handed metamaterials (LHM's) are a new media engineered to possess an effective negative index of refraction over a selected frequency range. This characteristic enables LHM's to exhibit physical properties never before observed. In particular, a negative index of refraction should cause electromagnetic radiation to refract or bend at a negative angle when entering an LHM, as shown in the figure above on the left. The figure on the right shows that this property could be used to bring radiation to a focus with a flat LHM lens. The advantage of a flat lens in comparison to a conventional curved lens is that the focal length could be varied simply by adjusting the distance between the lens and the electromagnetic wave source. In this in-house work, researchers at the NASA Glenn Research Center developed a computational model for LHM's with the three-dimensional electromagnetic commercial code Microwave Studio, constructed an LHM flat lens, and used it to experimentally demonstrate the reversed refraction and flat lens focusing of microwave radiation.

  13. Why are some people left-handed? An evolutionary perspective

    PubMed Central

    Llaurens, V.; Raymond, M.; Faurie, C.

    2008-01-01

    Since prehistoric times, left-handed individuals have been ubiquitous in human populations, exhibiting geographical frequency variations. Evolutionary explanations have been proposed for the persistence of the handedness polymorphism. Left-handedness could be favoured by negative frequency-dependent selection. Data have suggested that left-handedness, as the rare hand preference, could represent an important strategic advantage in fighting interactions. However, the fact that left-handedness occurs at a low frequency indicates that some evolutionary costs could be associated with left-handedness. Overall, the evolutionary dynamics of this polymorphism are not fully understood. Here, we review the abundant literature available regarding the possible mechanisms and consequences of left-handedness. We point out that hand preference is heritable, and report how hand preference is influenced by genetic, hormonal, developmental and cultural factors. We review the available information on potential fitness costs and benefits acting as selective forces on the proportion of left-handers. Thus, evolutionary perspectives on the persistence of this polymorphism in humans are gathered for the first time, highlighting the necessity for an assessment of fitness differences between right- and left-handers. PMID:19064347

  14. A survey of left-handed polyproline II helices.

    PubMed Central

    Stapley, B. J.; Creamer, T. P.

    1999-01-01

    Left-handed polyproline II helices (PPII) are contiguous elements of protein secondary structure in which the phi and psi angles of constituent residues are restricted to around -75 degrees and 145 degrees, respectively. They are important in structural proteins, in unfolded states and as ligands for signaling proteins. Here, we present a survey of 274 nonhomologous polypeptide chains from proteins of known structure for regions that form these structures. Such regions are rare, but the majority of proteins contain at least one PPII helix. Most PPII helices are shorter than five residues, although the longest found contained 12 amino acids. Proline predominates in PPII, but Gln and positively charged residues are also favored. The basis of Gln's prevalence is its ability to form an i, i + 1 side-chain to main-chain hydrogen bond with the backbone carbonyl oxygen of the proceeding residue; this helps to fix the psi angle of the Gln and the phi and psi of the proceeding residue in PPII conformations and explains why Gln is favored at the first position in a PPII helix. PPII helices are highly solvent exposed, which explains why apolar amino acids are disfavored despite preferring this region of phi/psi space when in isolation. PPII helices have perfect threefold rotational symmetry and within these structures we find significant correlation between the hydrophobicity of residues at i and i + 3; thus, PPII helices in globular proteins can be considered to be amphipathic. PMID:10091661

  15. Observation of tunable nonlinear effects in an analogue of superconducting composite right/left hand filter

    NASA Astrophysics Data System (ADS)

    Liu, Haiwen; Lei, Jiuhuai; Jiang, Hao; Guan, Xuehui; Ji, Laiyun; Ma, Zhewang

    2015-10-01

    Artificial structures with negative permittivity or permeability have attracted significant attention in the science community because they provide a pathway for obtaining exotic electromagnetic properties not found in natural materials. At the moment, the great challenge of these artificial structures in microwave frequency exhibits a relatively large loss. It is well-known that superconducting thin films have extremely low surface resistance. Hence, it is a good candidate to resolve this constraint. Besides, the reported artificial structures with negative permittivity or permeability are mainly focusing on linear regime of wave propagation. However, any future effort in creating tunable structures would require knowledge of nonlinear properties. In this work, a tunable superconducting filter with composite right/left-hand transmission property is proposed and fabricated. Its nonlinear effects on temperature and power are studied by theoretical analysis and experiments.

  16. Observation of tunable nonlinear effects in an analogue of superconducting composite right/left hand filter

    PubMed Central

    Liu, Haiwen; Lei, Jiuhuai; Jiang, Hao; Guan, Xuehui; Ji, Laiyun; Ma, Zhewang

    2015-01-01

    Artificial structures with negative permittivity or permeability have attracted significant attention in the science community because they provide a pathway for obtaining exotic electromagnetic properties not found in natural materials. At the moment, the great challenge of these artificial structures in microwave frequency exhibits a relatively large loss. It is well-known that superconducting thin films have extremely low surface resistance. Hence, it is a good candidate to resolve this constraint. Besides, the reported artificial structures with negative permittivity or permeability are mainly focusing on linear regime of wave propagation. However, any future effort in creating tunable structures would require knowledge of nonlinear properties. In this work, a tunable superconducting filter with composite right/left-hand transmission property is proposed and fabricated. Its nonlinear effects on temperature and power are studied by theoretical analysis and experiments. PMID:26442447

  17. Detonator comprising a nonlinear transmission line

    SciTech Connect

    Elizondo-Decanini, Juan M

    2014-12-30

    Detonators are described herein. In a general embodiment, the detonator includes a nonlinear transmission line that has a variable capacitance. Capacitance of the nonlinear transmission line is a function of voltage on the nonlinear transmission line. The nonlinear transmission line receives a voltage pulse from a voltage source and compresses the voltage pulse to generate a trigger signal. Compressing the voltage pulse includes increasing amplitude of the voltage pulse and decreasing length of the voltage pulse in time. An igniter receives the trigger signal and detonates an explosive responsive to receipt of the trigger signal.

  18. RF Transmission Lines on Silicon Substrates

    NASA Technical Reports Server (NTRS)

    Ponchak, George E.

    1999-01-01

    A review of RF transmission lines on silicon substrates is presented. Through measurements and calculated results, it is shown that attenuation is dominated by conductor loss if silicon substrates with a resistivity greater than 2500 Ohm-cm are used. Si passivation layers affect the transmission line attenuation; however, measured results demonstrate that passivation layers do not necessarily increase attenuation. If standard, low resistivity Si wafers must be used, alternative transmission lines such as thin film microstrip and Co-Planar Waveguide (CPW) on thick polyimide layers must be used. Measured results presented here show that low loss per unit length is achievable with these transmission lines.

  19. Transmission Line Security Monitor: Final Report

    SciTech Connect

    John Svoboda

    2011-04-01

    The Electric Power Transmission Line Security Monitor System Operational Test is a project funded by the Technical Support Working Group (TSWG). TSWG operates under the Combating Terrorism Technical Support Office that functions under the Department of Defense. The Transmission Line Security Monitor System is based on technology developed by Idaho National Laboratory. The technology provides a means for real-time monitoring of physical threats and/or damage to electrical transmission line towers and conductors as well as providing operational parameters to transmission line operators to optimize transmission line operation. The end use is for monitoring long stretches of transmission lines that deliver electrical power from remote generating stations to cities and industry. These transmission lines are generally located in remote transmission line corridors where security infrastructure may not exist. Security and operational sensors in the sensor platform on the conductors take power from the transmission line and relay security and operational information to operations personnel hundreds of miles away without relying on existing infrastructure. Initiated on May 25, 2007, this project resulted in pre-production units tested in realistic operational environments during 2010. A technology licensee, Lindsey Manufacturing of Azusa California, is assisting in design, testing, and ultimately production. The platform was originally designed for a security monitoring mission, but it has been enhanced to include important operational features desired by electrical utilities.

  20. Cultural and Environmental Pressure against Left-Hand Preference in Urban and Semi-Urban Malawi

    ERIC Educational Resources Information Center

    Zverev, Y. P.

    2006-01-01

    The study assessed views of teachers, pupils and their guardians on left-hand preference. Seventy-five percent of the responders indicated that the left hand should not be preferred for habitual activities and 87.6% of them indicated that left-handers should be forced to change the hand. Gender had significant effect on the view on left hand…

  1. Hand Preference and Skill in 115 Children of Two Left-Handed Parents.

    ERIC Educational Resources Information Center

    Annett, Marian

    1983-01-01

    Studied hand skill and performance in children (N=115) of left-handed parents using peg moving tasks and soccer kicks. Concluded that being raised by two left-handed parents does little to hinder the expression of the rs plus gene. Correlations for handedness in families depend more on genetics than experience. (Author/JAC)

  2. Simultaneous dielectric monitoring of microfluidic channels at microwaves utilizing a metamaterial transmission line structure.

    PubMed

    Schüßler, M; Puentes, M; Dubuc, D; Grenier, K; Jakoby, R

    2012-01-01

    The paper presents a technique that allows the simultaneous monitoring of the dielectric properties of liquids in microfluidic channels at microwave frequencies. It is capable of being integrated within the lab-on-a-chip concept and uses a composite right/left-handed transmission line resonator which is detuned by the dielectric loading of the liquids in the channels. By monitoring the change in the resonance spectrum of the resonator the loading profile can be derived with the multi-resonant perturbation method. From the value of the dielectric constant inference on the substances like cells or chemicals in the channels can be drawn. The paper presents concept, design, fabrication and characterization of prototype sensors. The sensors have been designed to operate between 20 and 30 GHz and were tested with water and water ethanol mixtures.

  3. A leaky-wave antenna using double-layered metamaterial transmission line

    NASA Astrophysics Data System (ADS)

    Xu, He-Xiu; Wang, Guang-Ming; Qi, Mei-Qing

    2013-05-01

    A novel leaky-wave antenna (LWA) is proposed using a double-layered resonant-type metamaterial (MTM) transmission line (TL). The MTM TL is composed of periodically arranged complementary split ring resonators (CSRRs), capacitive gaps, and metal caps. By introducing the extra metal cap in additional layer of the basic artificial MTM TL element, an increased left handed capacitor by 36 % with respect to that using none cap is engineered, which is necessary to implement a balanced condition, and thus a continuous beam steering property of the resultant LWA in terms of providing phase constants from negative to positive values. For verification, a 20-cells LWA sample is fabricated and measured. Consistent numerical and experimental results have both validated the continuous frequency-scanning capabilities of the antenna from backward -29° to forward 72° (including the broadside). The proposed prescription opens a way toward new types of MTM LWAs with easily engineered broadside radiation.

  4. Simultaneous dielectric monitoring of microfluidic channels at microwaves utilizing a metamaterial transmission line structure.

    PubMed

    Schüßler, M; Puentes, M; Dubuc, D; Grenier, K; Jakoby, R

    2012-01-01

    The paper presents a technique that allows the simultaneous monitoring of the dielectric properties of liquids in microfluidic channels at microwave frequencies. It is capable of being integrated within the lab-on-a-chip concept and uses a composite right/left-handed transmission line resonator which is detuned by the dielectric loading of the liquids in the channels. By monitoring the change in the resonance spectrum of the resonator the loading profile can be derived with the multi-resonant perturbation method. From the value of the dielectric constant inference on the substances like cells or chemicals in the channels can be drawn. The paper presents concept, design, fabrication and characterization of prototype sensors. The sensors have been designed to operate between 20 and 30 GHz and were tested with water and water ethanol mixtures. PMID:23367363

  5. SPP-associated dual left-handed bands and field enhancement in metal-dielectric-metal metamaterial perforated by asymmetric cross hole arrays.

    PubMed

    Ding, P; Liang, E J; Hu, W Q; Zhou, Q; Zhang, L; Yuan, Y X; Xue, Q Z

    2009-02-16

    Dual-band left-handed transmissions in the near infrared frequencies through the metal-dielectric-metal metamaterial perforated with an array of asymmetric cross holes are demonstrated. It is shown that the left-handed bands originate from the SPP-associated magnetic response excited by different polarized light and their frequencies can be tuned by the arm's length or width of the cross-gaps. The structures are further optimized at 1.064 microm laser light excitation for elucidating the mechanism and possible application in surface enhanced Raman spectroscopy in sandwiched architectures. This study provides valuable information for the design of compact optical devices with dual left-handed bands in a single structure and may also pave the way toward stable and reproducible substrate design for surface enhanced Raman spectroscopy.

  6. Single transmission line data acquisition system

    DOEpatents

    Fasching, George E.

    1984-01-01

    A single transmission line interrogated multiple channel data acquisition system is provided in which a plurality of remote station/sensors monitor specific process variables and transmit measurement values over the single transmission line to a master station when addressed by the master station. Power for all remote stations (up to 980) is provided by driving the line with constant voltage supplied from the master station and automatically maintained independent of the number of remote stations directly connected to the line. The transmission line can be an RG-62 coaxial cable with lengths up to about 10,000 feet with branches up to 500 feet. The remote stations can be attached randomly along the line. The remote stations can be scanned at rates up to 980 channels/second.

  7. Electrical Transmission Line Diametrical Retention Mechanism

    DOEpatents

    Hall, David R.; Hall, Jr., H. Tracy; Pixton, David; Dahlgren, Scott; Sneddon, Cameron; Briscoe, Michael; Fox, Joe

    2006-01-03

    The invention is a mechanism for retaining an electrical transmission line. In one embodiment of the invention it is a system for retaining an electrical transmission line within downhole components. The invention allows a transmission line to be attached to the internal diameter of drilling components that have a substantially uniform drilling diameter. In accordance with one aspect of the invention, the system includes a plurality of downhole components, such as sections of pipe in a drill string, drill collars, heavy weight drill pipe, and jars. The system also includes a coaxial cable running between the first and second end of a drill pipe, the coaxial cable having a conductive tube and a conductive core within it. The invention allows the electrical transmission line to withstand the tension and compression of drill pipe during routine drilling cycles.

  8. Left-handed materials and negative refraction: Transfer matrix and FDTD calculations

    NASA Astrophysics Data System (ADS)

    Soukoulis, Costas M.

    2004-03-01

    We will present transfer matrix calculations of metallic wires, split ring resonators (SRR) and left-handed materials (LHM). Our results [1] show that the transfer matrix method can capture all the details characteristics of the metamaterials. In particular the dependence of the resonance frequency and its width on the structural parameters of the SRR and the size of the unit cell is studied. Also the dependence of the imaginary part of effective permittivity of arrays of metallic wires is studied in detail. It is found [2,3] that the imaginary part of effective permittivity has small values even for wires as small as 20 micron in diameter. The transfer matrix is very useful in calculating both the amplitude and the phase of the transmission and reflection coefficient. These numerical data was used [4] in the determination of the effective parameters of the metamaterials. It was indeed found that the refractive index was unambiguously negative in the frequency region where both ɛ and μ were negative. Finally, we will show that SRR have a strong electric response, equivalent to that of cut wires [5], which dominates the response of LHM. A new criterion is introduced to clearly identify if an experimental expression peak is left- or right handed. Finite difference time domain (FDTD) simulations will be presented for the transmission of the EM wave through the interface of the positive and negative refraction index. It is found [6] that the wave is trapped temporarily at the interface and after a long time the wave front moves eventually in the direction of negative refraction. The differences between negative refraction in photonic crystals and left-handed materials will be also discussed. Work supported by US-DOE, DARPA, NSF and EU (DALHM project). References: [1] P. Markos and C. M. Soukoulis, Phys. Rev. B 65, 033401 (2002); Phys. Rev. E 65, 036622 (2002). [2] P. Markos, I. Rousochatzakis and C. M. Soukoulis, Phys. Rev. B 66, 045601 (2002). [3] P. Markos and C. M

  9. Transmission Line Series Compensation for Wind Energy Transmission

    NASA Astrophysics Data System (ADS)

    Palanichamy, Dr C., Prof; Wong, Y. C.

    2015-04-01

    Wind energy has demonstrated to be a clean, copious and absolutely renewable source of energy, and the large penetration of it into the power grid indicates that wind energy is considered an effective means of power generation, Transmission of wind energy from remote locations to load centers necessitates long transmission lines. Series compensation is a proven and economical transmission solution to address system power transfer strength, grid stability, and voltage profile issues of long transmission lines. In this paper, a programmable approach to determine the capacitive reactance of series capacitor and optimum location for its placement to achieve maximum power transfer gas been presented. The respective program with sample solutions has been provided for real-time applications.

  10. Effect of tornado loads on transmission lines

    SciTech Connect

    Ishac, M.F.; White, H.B.

    1994-12-31

    Of all the populated areas in Canada, southwestern Ontario has experienced the highest tornado incidence and faces the greatest tornado damage. About 1 or 2 tornadoes per 10,000 km{sup 2} can be expected there annually. The probability of a tornado strike at a given point is very small but the probability of a transmission line being crossed by a tornado is significant. The purpose of this paper is to review the literature related to tornadoes in Ontario and to investigate the effect of tornado loads on transmission lines. Based on this investigation a design basis tornado loading for transmission towers is proposed.

  11. Effect of tornado loads on transmission lines

    SciTech Connect

    Ishac, M.F.; White, H.B.

    1995-01-01

    Of all the populated areas in Canada, southwestern Ontario has experienced the highest tornado incidence and faces the greatest tornado damage. About 1 or 2 tornadoes per 10,000 km{sup 2} can be expected there annually. The probability of a tornado strike at a given point is very small but the probability of a transmission line being crossed by a tornado is significant. The purpose of this paper is to review the literature related to tornadoes in Ontario and to investigate the effect of tornado loads on transmission lines. Based on this investigation a design basis tornado loading for transmission towers is proposed.

  12. Concurrent Wind Cooling in Power Transmission Lines

    SciTech Connect

    Jake P Gentle

    2012-08-01

    Idaho National Laboratory and the Idaho Power Company, with collaboration from Idaho State University, have been working on a project to monitor wind and other environmental data parameters along certain electrical transmission corridors. The combination of both real-time historical weather and environmental data is being used to model, validate, and recommend possibilities for dynamic operations of the transmission lines for power and energy carrying capacity. The planned results can also be used to influence decisions about proposed design criteria for or upgrades to certain sections of the transmission lines.

  13. Bird streamer flashovers on FPL transmission lines

    SciTech Connect

    Burnham, J.T.

    1995-04-01

    FPL transmission lines with excessive unknown cause outages were investigated and determined to have experiences bird streamer flashovers. Findings are extended to similar lines and the frequency of bird streamer occurrences are estimated. Outage patterns associated with bird streamer flashovers are presented.

  14. Upgrading a 24-in. gas transmission line

    SciTech Connect

    Stiles, R.E.

    1986-10-01

    Because of increasing population density, Texas Eastern Transmission Corp. removed an existing 24-in. gas line and replaced it with a higher yield line pipe with a greater wall thickness. Work was through exclusive lake subdivisions and across a golf course and required special construction techniques.

  15. Load-resistant coaxial transmission line

    DOEpatents

    Hall, David R.; Fox, Joe

    2006-01-03

    A transmission line for downhole tools that make up all or part of a tool string for drilling and production of oil, gas, and geothermal wells that can withstand the dynamic gravitational forces and other accelerations associated with downhole excavations. The transmission line has a metal tube, or outer conductor, that houses a coaxial wire inner conductor. A non-metallic dielectric material is interposed between the inner and outer conductors. The outer and inner conductors and the dielectric are sufficiently compressed together so that independent motion between them is abated. Compression of the components of the transmission line may be achieved by drawing the transmission through one or more dies in order to draw down the outer conductor onto the dielectric, or by expanding the inner conductor against the dielectric using a mandrel or hydraulic pressure. Non-metallic bead segments may be used in aid of the compression necessary to resist the dynamic forces and accelerations of drilling.

  16. Quasi-phase-matching of the dual-band nonlinear left-handed metamaterial

    SciTech Connect

    Liu, Yahong Song, Kun; Gu, Shuai; Liu, Zhaojun; Guo, Lei; Zhao, Xiaopeng; Zhou, Xin

    2014-11-17

    We demonstrate a type of nonlinear meta-atom creating a dual-band nonlinear left-handed metamaterial (DNLHM). The DNLHM operates at two distinct left-handed frequency bands where there is an interval of one octave between the two center frequencies. Under the illumination of a high-power signal at the first left-handed frequency band corresponding to fundamental frequency (FF), second-harmonic generation (SHG) is observed at the second left-handed band. This means that our DNLHM supports backward-propagating waves both at FF and second-harmonic (SH) frequency. We also experimentally demonstrate quasi-phase-matching configurations for the backward SHG. This fancy parametric process can significantly transmits the SH generated by an incident FF wave.

  17. Quasi-phase-matching of the dual-band nonlinear left-handed metamaterial

    NASA Astrophysics Data System (ADS)

    Liu, Yahong; Zhou, Xin; Song, Kun; Gu, Shuai; Liu, Zhaojun; Guo, Lei; Zhao, Xiaopeng

    2014-11-01

    We demonstrate a type of nonlinear meta-atom creating a dual-band nonlinear left-handed metamaterial (DNLHM). The DNLHM operates at two distinct left-handed frequency bands where there is an interval of one octave between the two center frequencies. Under the illumination of a high-power signal at the first left-handed frequency band corresponding to fundamental frequency (FF), second-harmonic generation (SHG) is observed at the second left-handed band. This means that our DNLHM supports backward-propagating waves both at FF and second-harmonic (SH) frequency. We also experimentally demonstrate quasi-phase-matching configurations for the backward SHG. This fancy parametric process can significantly transmits the SH generated by an incident FF wave.

  18. METHODOLOGICAL NOTES: What are the left-handed media and what is interesting about them?

    NASA Astrophysics Data System (ADS)

    Bliokh, Konstantin Yu; Bliokh, Yurii P.

    2004-04-01

    We review the intensively discussed ideas about wave propagation and refraction in media where both electric permittivity and magnetic permeability are negative. The criticism against negative refraction as violating the causality principle is considered. Starting from the initial wave equations, refraction of beams at the boundary of a left-handed medium is analyzed. The physics of a perfect lens formed by a flat layer of a left-handed material is considered.

  19. Human mitochondrial mTERF wraps around DNA through a left-handed superhelical tandem repeat.

    PubMed

    Jiménez-Menéndez, Nereida; Fernández-Millán, Pablo; Rubio-Cosials, Anna; Arnan, Carme; Montoya, Julio; Jacobs, Howard T; Bernadó, Pau; Coll, Miquel; Usón, Isabel; Solà, Maria

    2010-07-01

    The regulation of mitochondrial DNA (mtDNA) processes is slowly being characterized at a structural level. We present here crystal structures of human mitochondrial regulator mTERF, a transcription termination factor also implicated in replication pausing, in complex with double-stranded DNA oligonucleotides containing the tRNA(Leu)(UUR) gene sequence. mTERF comprises nine left-handed helical tandem repeats that form a left-handed superhelix, the Zurdo domain.

  20. Transmission Line Adapted Analytical Power Charts Solution

    NASA Astrophysics Data System (ADS)

    Sakala, Japhet D.; Daka, James S. J.; Setlhaolo, Ditiro; Malichi, Alec Pulu

    2016-08-01

    The performance of a transmission line has been assessed over the years using power charts. These are graphical representations, drawn to scale, of the equations that describe the performance of transmission lines. Various quantities that describe the performance, such as sending end voltage, sending end power and compensation to give zero voltage regulation, may be deduced from the power charts. Usually required values are read off and then converted using the appropriate scales and known relationships. In this paper, the authors revisit this area of circle diagrams for transmission line performance. The work presented here formulates the mathematical model that analyses the transmission line performance from the power charts relationships and then uses them to calculate the transmission line performance. In this proposed approach, it is not necessary to draw the power charts for the solution. However the power charts may be drawn for the visual presentation. The method is based on applying derived equations and is simple to use since it does not require rigorous derivations.

  1. Application of transmission-line super theory to classical transmission lines with risers

    NASA Astrophysics Data System (ADS)

    Rambousky, R.; Nitsch, J.; Tkachenko, S.

    2015-11-01

    By applying the Transmission-Line Super Theory (TLST) to a practical transmission-line configuration (two risers and a horizontal part of the line parallel to the ground plane) it is elaborated under which physical and geometrical conditions the horizontal part of the transmission-line can be represented by a classical telegrapher equation with a sufficiently accurate description of the physical properties of the line. The risers together with the part of the horizontal line close to them are treated as separate lines using the TLST. Novel frequency and local dependent reflection coefficients are introduced to take into account the action of the bends and their radiation. They can be derived from the matrizant elements of the TLST solution. It is shown that the solution of the resulting network and the TLST solution of the entire line agree for certain line configurations. The physical and geometrical parameters for these corresponding configurations are determined in this paper.

  2. EC Transmission Line Risk Identification and Analysis

    SciTech Connect

    Bigelow, Tim S

    2012-04-01

    The purpose of this document is to assist in evaluating and planning for the cost, schedule, and technical project risks associated with the delivery and operation of the EC (Electron cyclotron) transmission line system. In general, the major risks that are anticipated to be encountered during the project delivery phase associated with the implementation of the Procurement Arrangement for the EC transmission line system are associated with: (1) Undefined or changing requirements (e.g., functional or regulatory requirements) (2) Underperformance of prototype, first unit, or production components during testing (3) Unavailability of qualified vendors for critical components Technical risks associated with the design and operation of the system are also identified.

  3. Flux Cloning in Josephson Transmission Lines

    SciTech Connect

    Gulevich, D.R.; Kusmartsev, F.V.

    2006-07-07

    We describe a novel effect related to the controlled birth of a single Josephson vortex. In this phenomenon, the vortex is created in a Josephson transmission line at a T-shaped junction. The 'baby' vortex arises at the moment when a 'mother' vortex propagating in the adjacent transmission line passes the T-shaped junction. In order to give birth to a new vortex, the mother vortex must have enough kinetic energy. Its motion can also be supported by an externally applied driving current. We determine the critical velocity and the critical driving current for the creation of the baby vortices and briefly discuss the potential applications of the found effect.

  4. 18 CFR 2.2 - Transmission lines.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Transmission lines. 2.2 Section 2.2 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

  5. 18 CFR 2.2 - Transmission lines.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Transmission lines. 2.2 Section 2.2 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

  6. 18 CFR 2.2 - Transmission lines.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 1 2013-04-01 2013-04-01 false Transmission lines. 2.2 Section 2.2 Conservation of Power and Water Resources FEDERAL ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY GENERAL RULES GENERAL POLICY AND INTERPRETATIONS Statements of General Policy and...

  7. Fluxon propagation on a Josephson transmission line

    SciTech Connect

    Matsuda, A.; Kawakami, T.

    1983-08-22

    Fluxon propagation profiles for Josephson transmission lines have been directly measured. Single--input-pulse dissociation into multifluxon as well as velocity-dependent wave forms have actually been observed. The experimental results agree well with the theoretical results if a large rf loss term is assumed.

  8. Bimanual proprioceptive performance differs for right- and left-handed individuals.

    PubMed

    Han, Jia; Waddington, Gordon; Adams, Roger; Anson, Judith

    2013-05-10

    It has been proposed that asymmetry between the upper limbs in the utilization of proprioceptive feedback arises from functional differences in the roles of the preferred and non-preferred hands during bimanual tasks. The present study investigated unimanual and bimanual proprioceptive performance in right- and left-handed young adults with an active finger pinch movement discrimination task. With visual information removed, participants were required to make absolute judgments about the extent of pinch movements made to physical stops, either by one hand, or by both hands concurrently, with the sequence of presented movement extents varied randomly. Discrimination accuracy scores were derived from participants' responses using non-parametric signal detection analysis. Consistent with previous findings, a non-dominant hand/hemisphere superiority effect was observed, where the non-dominant hands of right- and left-handed individuals performed overall significantly better than their dominant hands. For all participants, bimanual movement discrimination scores were significantly lower than scores obtained in the unimanual task. However, the magnitude of the performance reduction, from the unimanual to the bimanual task, was significantly greater for left-handed individuals. The effect whereby bimanual proprioception was disproportionately affected in left-handed individuals could be due to enhanced neural communication between hemispheres in left-handed individuals leading to less distinctive separation of information obtained from the two hands in the cerebral cortex.

  9. Are there excitability changes in the hand motor cortex during speech in left-handed subjects?

    PubMed

    Tokimura, Hiroshi; Tokimura, Yoshika; Arita, Kazunori

    2012-01-01

    Hemispheric dominance was investigated in left-handed subjects using single transcranial magnetic stimulation to assess the possible effect of forced change in the dominant hand. Single transcranial magnetic stimuli were delivered randomly over the hand area of the left or right motor cortex of 8 Japanese self-declared left-handed adult volunteers. Electromyographic responses were recorded in the relaxed first dorsal interosseous muscle while the subjects read aloud. Laterality quotient calculated by the Edinburgh Inventory ranged from -100 to -5.26 and laterality index calculated from motor evoked potentials ranged from -86.2 to 38.8. There was no significant correlation between laterality quotient and laterality index. Mean data values across all 8 subjects indicated significant increases only in the left hand. Our ratio analysis of facilitation of the hand motor potentials showed that 2 each of the 8 self-declared left-handers were right- and left-hand dominant and the other 4 were bilateral-hand dominant. Speech dominancy was localized primarily in the right cerebral hemisphere in left-handed subjects, but some individuals exhibited bilateral or left dominance, possibly attributable to the forced change of hand preference for writing in childhood. Our findings suggest changes in the connections between the speech and hand motor areas.

  10. Unusual entanglement transformation properties of the quantum radiation through one-dimensional random system containing left-handed-materials.

    PubMed

    Dong, Yunxia; Zhang, Xiangdong

    2008-10-13

    The quantum radiation through the multilayer structures containing the left-handed materials is investigated based on the Green-function approach to the quantization of the phenomenological Maxwell theory. Emphasis is placed on the effect of randomness on the generation and transmission of entangled-states. It is shown that some unusual properties appear for the present systems in comparison with those of the conventional dielectric structures. The quantum relative entropy is always enhanced with the increase of random degree due to the existence of nonlocalized mode in the present systems, while the maximal entanglement can be observed only at some certain randomness for the conventional dielectric structures. In contrast to exponential decrease in the conventional systems, the entanglement degrades slowly with the increase of disorder and thickness of the sample near the nonlocalized mode after transmission through the present systems. This will benefit the quantum communication for long distances.

  11. Transmission line environmental assessment guidance document

    SciTech Connect

    Jackson, J.; Pentecost, E.; Muzzarelli, J.

    1994-01-01

    Since 1939, U.S. utility companies have been required to obtain a Presidential Permit to construct electric transmission lines that cross a U.S. border and connect with a foreign utility. The purpose of this document is to provide Presidential Permit applicants with two types of guidance: (1) on the type of environmental and project descriptive information needed to assess the potential impacts of the proposed and alternative actions and (2) on compliance with applicable federal and state regulations. The main three chapters present information on the purpose and content of this document (Chapter 1); legislative, regulatory, and consultation requirements for transmission line interconnect projects (Chapter 2); and identification of basic transmission system design parameters and environmental data requirements for analysis of potential impacts of the proposed action (Chapter 3). Chapter 3 also includes information on possible techniques or measures to mitigate impacts. Appendix A presents an overview of NEPA requirements and DOE`s implementing procedures. Appendix B summarizes information on legislation that may be applicable to transmission line projects proposed in Presidential Permit applications.

  12. Left-handed properties dependence versus the interwire distance in Fe-based microwires metastructures

    NASA Astrophysics Data System (ADS)

    Ababei, Gabriel; Olariu, Cristina Stefania; Lupu, Nicoleta; Chiriac, Horia

    2016-05-01

    Experimental and theoretical investigations on the left-handed properties dependence versus the interwire distance of three new proposed Fe77.5Si7.5B15 glass coated microwires-based metastructures are presented. The left-handed characteristics of the metastructures were determined in the frequency range 8.2 ÷ 12 GHz and external d.c. magnetic fields ranging from 0 to 32 kA/m. The experimental results show that the electromagnetic losses of the metastructures increase with the decreasing of the interwire distance due to the increasing of the long-range dynamic dipole-dipole interaction within inter-wires in the presence of the microwave field. The numerical calculations using Nicolson-Weiss-Ross algorithm are in agreement with the experimental results. The variation of the interwire distance proves to be a useful tool to obtain metastructures with controlled left-handed characteristics.

  13. Birefringent left-handed metamaterials and perfect lenses for vectorial fields

    NASA Astrophysics Data System (ADS)

    Zharov, Alexander A.; Zharova, Nina A.; Noskov, Roman E.; Shadrivov, Ilya V.; Kivshar, Yuri S.

    2005-10-01

    We describe the properties of specific non-reflecting birefringent left-handed metamaterials and demonstrate a birefringent perfect lens for vectorial fields. We predict that, in a sharp contrast to the concept of a conventional perfect lens realized at epsi = μ = -1 (where epsi is the dielectric permittivity and μ is the magnetic permeability), the birefringent left-handed slab possesses the property of negative refraction either for TE- or TM-polarized waves or for both of them simultaneously. This allows selective focusing and a spatial separation of the images created at different polarizations. We discuss several applications of the birefringent left-handed lenses such as the beam splitting and near-field diagnostics at the sub-wavelength scale.

  14. Electroinductive waves role in left-handed stacked complementary split rings resonators.

    PubMed

    Beruete, M; Aznabet, M; Navarro-Cía, M; El Mrabet, O; Falcone, F; Aknin, N; Essaaidi, M; Sorolla, M

    2009-02-01

    In this letter it is presented a Left-Handed Metamaterial design route based upon stacked arrays of screens made of complementary split rings resonators under normal incidence in the microwave regime. Computation of the dispersion diagram highlights the possibility to obtain backward waves provided the longitudinal lattice is small enough. The experimental results are in good agreement with the computed ones. The physics underlying the Left-Handed behavior is found to rely on electroinductive waves, playing the mutual capacitive coupling the major role to explain the phenomenon. Our route to Left-Handed metamaterial introduced in this paper based on stacking CSRRs screens can be scaled to millimeter and terahertz for future applications.

  15. Optical refractive index of massive particles and physical meanings of left-handed media [rapid communication

    NASA Astrophysics Data System (ADS)

    Shen, Jian Qi

    2005-09-01

    In this Letter the expression for the refractive index of de Broglie wave in the presence of a potential field is obtained and based on this, the physical meanings of negative index of refraction is revealed. We demonstrate that the electromagnetic wave propagation in a left-handed medium with negative refractive index behaves just like that of antiphotons, which is required of the complex vector field theory. It is believed that the complex vector field theory is helpful in considering the wave propagation and photonic band gap structures in the left-handed medium photonic crystals with a periodicity in negative and positive indices of refraction.

  16. Sub-wavelength imaging with a left-handed material flat lens

    NASA Astrophysics Data System (ADS)

    Feise, Michael W.; Kivshar, Yuri S.

    2005-01-01

    We study numerically, by means of the pseudospectral time-domain method, the unique features of imaging by a flat lens made of a left-handed metamaterial that possesses the property of negative refraction. We confirm the earlier finding that a left-handed flat lens can provide near-perfect imaging of a point source and a pair of point sources with clear evidence of sub-wavelength resolution. We illustrate the limitation of the resolution in the time-integrated image due to the presence of surface waves.

  17. Comparisons of Negative Refraction in Left-Handed Materials and Photonic Crystals

    NASA Astrophysics Data System (ADS)

    Feng, Liang; Liu, Xiao-Ping; Ren, Jie; Chen, Yan-Feng; Zhu, Yong-Yuan

    Using the equifrequency surfaces (EFS) to describe negative refractions in left-handed materials (LHMs) and photonic crystals (PCs), negative phase and negative group refractive indexes in LHMs were compared with positive phase and negative group refractive indexes in PCs. The refractive indexes in PCs were dependent on frequencies and incident angles of electromagnetic wave, while indexes in LHMs were constant in the left-handed region. Furthermore, the phase compensating effect resulting from the negative phase refractive index was addressed to distinguish the perfect lens made of LHMs from the superlens realized in the all angle negative refraction (AANR) region of PCs.

  18. Wave propagation in parallel-plate waveguides filled with nonlinear left-handed material

    NASA Astrophysics Data System (ADS)

    Burhan, Zamir; Rashid, Ali

    2011-01-01

    A theoretical investigation of field components for transverse electric mode in the parallel-plate waveguides has been studied. In this analysis two different types of waveguide structures have been discussed, i.e., (a) normal good/perfect conducting parallel-plate waveguide filled with nonlinear left-handed material and (b) high-temperature-superconducting parallel-plate waveguide filled with nonlinear left-handed material. The dispersion relations of transverse electric mode have also been discussed for these two types of waveguide structures.

  19. Radiation characteristics of electromagnetic eigenmodes at the corrugated interface of a left-handed material.

    PubMed

    Cuevas, Mauro; Depine, Ricardo A

    2009-08-28

    We study the radiation characteristics of electromagnetic surface waves at a periodically corrugated interface between a conventional and a negatively refracting (or left-handed) material. In this case, and contrary to the surface plasmon polariton in a metallic grating, surface plasmon polaritons may radiate on both sides of the rough interface along which they propagate. We find novel radiation regimes which provide an indirect demonstration of other unusual phenomena characteristic of electromagnetic wave propagation in left-handed materials, such as negative refraction or backward wave propagation.

  20. Two Left Hands, Ten Interlaced Fingers: A New Rubber Hand Illusion.

    PubMed

    White, Rebekah C; Bowen, Dillon; Dumbalska, Tsvetomira; Hoeger, Katharine; Mok, Anastasia Y S

    2016-03-01

    A variation on the rubber hand paradigm elicits an illusion in which the participant's sense of body ownership can switch back and forth between two viewed prosthetic hands. The interlaced fingers paradigm involves three prosthetic left hands: Two are positioned in full view of the participant, with their fingers interlaced, and the fingers of a third prosthetic hand are interlaced with the fingers of the participant's left hand, which is hidden from view. The examiner alternates brushstrokes to the two viewed prosthetic hands, while administering synchronous brushstrokes to the participant's hidden hand. Most participants experience ownership for the prosthetic hand that is being stroked at a given moment.

  1. Ferrite-based magnetically tunable left-handed metamaterial composed of SRRs and wires.

    PubMed

    Kang, Lei; Zhao, Qian; Zhao, Hongjie; Zhou, Ji

    2008-10-27

    We experimentally demonstrate a magnetically tunable left-handed metamaterial by introducing yttrium iron garnet rods into SRRs/wires array. It shows that the left-handed passband of the metamaterial can be continuously and reversibly adjusted by external dc applied magnetic fields. Retrieved effective parameters based on simulated scattering parameters show that tunable effective refraction index can be conveniently realized in a broad frequency range by changing the applied magnetic field. Different from those tuned by controlling the capacitance of equivalent LC circuit of SRR, this metamaterial is based on a mechanism of magnetically tuning the inductance via the active ambient effective permeability.

  2. Artificial magnetism and left-handed media from dielectric rings and rods.

    PubMed

    Jelinek, L; Marqués, R

    2010-01-20

    It is shown that artificial magnetism with relatively large frequency bandwidth can be obtained from periodic arrangements of dielectric rings. Combined with dielectric rods, dielectric rings can provide 3D isotropic left-handed metamaterials which are an advantageous alternative to metallic split ring resonators (SRRs) and/or metallic wires when undetectability by low frequency external magnetic fields is desired. Furthermore it is shown that, unlike conventional SRRs, dielectric rings can also be combined with natural plasma-like media to obtain a left-handed metamaterial.

  3. 7 CFR 1726.77 - Substation and transmission line construction.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 11 2012-01-01 2012-01-01 false Substation and transmission line construction. 1726... and Transmission Facilities § 1726.77 Substation and transmission line construction. (a) Contract... substation and transmission line construction (including minor modifications or improvements), exclusive...

  4. 7 CFR 1726.77 - Substation and transmission line construction.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 11 2011-01-01 2011-01-01 false Substation and transmission line construction. 1726... and Transmission Facilities § 1726.77 Substation and transmission line construction. (a) Contract... substation and transmission line construction (including minor modifications or improvements), exclusive...

  5. 7 CFR 1726.77 - Substation and transmission line construction.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 11 2014-01-01 2014-01-01 false Substation and transmission line construction. 1726... and Transmission Facilities § 1726.77 Substation and transmission line construction. (a) Contract... substation and transmission line construction (including minor modifications or improvements), exclusive...

  6. 7 CFR 1726.77 - Substation and transmission line construction.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 11 2013-01-01 2013-01-01 false Substation and transmission line construction. 1726... and Transmission Facilities § 1726.77 Substation and transmission line construction. (a) Contract... substation and transmission line construction (including minor modifications or improvements), exclusive...

  7. Accelerator power concepts using isolated transmission lines

    SciTech Connect

    Nunnally, W.C.

    1981-05-01

    This report outlines the rationale and the advantages of using multiple transmission-line sections isolated by transit time and inductance in accelerating high-current (approx. = 10 -kA), short-pulse (less than or equal to 100-ns) particle beams to the multimegavolt level. The main advantages of this system include reducing the number of output switches required per output pulse by nearly an order of magnitude over conventional systems and increasing the system capability for repetition-rate operation. The isolated transmission-line concept is developed, and possible modes of operation are outlined. In addition, a point design of a 10-kA short-pulse accelerator is presented.

  8. Application of composite insulators to transmission lines

    SciTech Connect

    Cherney, E.A.; Brown, R.L.; Karady, G.; Nicholls, J.L.; Orbeck, T.; Pargamin, L.

    1983-05-01

    The paper provides guidelines for the application of composite insulators to transmission lines. These guidelines are based on utility field experiences, results of research laboratory tests and manufacturers' recommendations. Discussed are interchangeability with porcelain and glass insulators, application in contaminated environments, material ageing, insulator icing, the use of grease, resistance to vandalism, temperature extremes, and the need for grading rings. Clarification is provided on the mechanical rating of composite insulators because there is not yet general agreement by various industry groups.

  9. Microstrip transmission line for soil moisture measurement

    NASA Astrophysics Data System (ADS)

    Chen, Xuemin; Li, Jing; Liang, Renyue; Sun, Yijie; Liu, C. Richard; Rogers, Richard; Claros, German

    2004-12-01

    Pavement life span is often affected by the amount of voids in the base and subgrade soils, especially moisture content in pavement. Most available moisture sensors are based on the capacitive sensing using planar blades. Since the planar sensor blades are fabricated on the same surface to reduce the overall size of the sensor, such structure cannot provide very high accuracy for moisture content measurement. As a consequence, a typical capacitive moisture sensor has an error in the range of 30%. A more accurate measurement is based on the time domain refelctometer (TDR) measurement. However, typical TDR system is fairly expensive equipment, very large in size, and difficult to operate, the moisture content measurement is limited. In this paper, a novel microstrip transmission line based moisture sensor is presented. This sensor uses the phase shift measurement of RF signal going through a transmission line buried in the soil to be measured. Since the amplitude of the transmission measurement is a strong function of the conductivity (loss of the media) and the imaginary part of dielectric constant, and the phase is mainly a strong function of the real part of the dielectric constant, measuring phase shift in transmission mode can directly obtain the soil moisture information. This sensor was designed and implemented. Sensor networking was devised. Both lab and field data show that this sensor is sensitive and accurate.

  10. Effect of different metallic nano-inclusions (Ag, Al, Au and Cu) and gain assistance for isotropic left-handed photonic material in blue light region

    NASA Astrophysics Data System (ADS)

    Rajput, M.; Sinha, R. K.; Varshney, S. K.

    2013-07-01

    A gain assisted Double Negative-Metallo-Semiconductor Photonic Crystal (DN-MSPC) for blue light with effect of different plasmonic (Al, Ag, Au, Cu) nanorod inclusions is presented. Effect of different metal nanocomposites and inverted host matrix, on dispersion and transmission properties of the designed DN-MSPC is demonstrated. Negative real values of both permeability (μ) and permittivity (ɛ) with extremely low imaginary values in the visible region are obtained by applying coupled dipole approximation for different nanocomposites. It is shown that index matching to the incident medium and compensated losses due to the gain assistance lead to the light amplification in the designed structure. A comparison of dispersion properties and left-handed resonance for different plasmonic nanocomposites of a similar shape and geometry shows permittivity-dependent dispersion and resonant properties. Fabrication tolerance with effect of change in plasmonic nanorod radius by ±10% is also analyzed. Furthermore, the sensitivity of the left-handed transmission to index changes of the host material (i.e., refractive index sensitivity) and highest left-handed transmission efficiency (>99%) is also investigated for biosensing application.

  11. Evidence for right-hand feeding biases in a left-handed population.

    PubMed

    Flindall, Jason W; Stone, Kayla D; Gonzalez, Claudia L R

    2015-05-01

    We have recently shown that actions with similar kinematic requirements, but different end-state goals may be supported by distinct neural networks. Specifically, we demonstrated that when right-handed individuals reach-to-grasp food items with intent to eat, they produce smaller maximum grip apertures (MGAs) than when they grasp the same item with intent to place it in a location near the mouth. This effect was restricted to right-handed movements; left-handed movements showed no difference between tasks. The current study investigates whether (and to which side) the effect may be lateralized in left-handed individuals. Twenty-one self-identified left-handed participants grasped food items of three different sizes while grasp kinematics were captured via an Optotrak Certus motion capture array. A main effect of task was identified wherein the grasp-to-eat action generated significantly smaller MGAs than did the grasp-to-place action. Further analysis revealed that similar to the findings in right-handed individuals, this effect was significant only during right-handed movements. Upon further inspection however, we found individual differences in the magnitude and direction of the observed lateralization. These results underscore the evolutionary significance of the grasp-to-eat movement in producing population-level right-handedness in humans as well as highlighting the heterogeneity of the left-handed population.

  12. Comparative analysis of brain EEG signals generated from the right and left hand while writing

    NASA Astrophysics Data System (ADS)

    Sardesai, Neha; Jamali Mahabadi, S. E.; Meng, Qinglei; Choa, Fow-Sen

    2016-05-01

    This paper provides a comparative analysis of right handed people and left handed people when they write with both their hands. Two left handed and one right handed subject were asked to write their respective names on a paper using both, their left and right handed, and their brain signals were measured using EEG. Similarly, they were asked to perform simple mathematical calculations using both their hand. The data collected from the EEG from writing with both hands is compared. It is observed that though it is expected that the right brain only would contribute to left handed writing and vice versa, it is not so. When a right handed person writes with his/her left hand, the initial instinct is to go for writing with the right hand. Hence, both parts of the brain are active when a subject writes with the other hand. However, when the activity is repeated, the brain learns to expect to write with the other hand as the activity is repeated and then only the expected part of the brain is active.

  13. A Left Handed Compliment: A newly discovered, early nineteenth-century lithograph by John Lewis Marks.

    PubMed

    McManus, I C; Snowman, Janet

    2010-01-01

    A newly discovered, early nineteenth-century lithograph by John Lewis Marks (b. ca. 1795-1796, d. ca. 1857-1861), entitled A Left Handed Compliment, is described. In this humorous print a young boy is using his left hand to draw the face of an elderly woman who is his grandmother, and she is shocked at the boy's suggestion that he will, “just see if I can't touch off your old Phizog left handed”. The source of the joke about the left-handed compliment is obscure, but more than likely it is sexual in origin. Glued to the verso of the print are early versions of two prints by Robert Seymour (1798-1836), the illustrator of Dickens' Pickwick Papers, suggesting a possible link between Marks and Seymour. From the hatch patterns on the Seymour engravings, it appears that Seymour may himself have been left-handed and perhaps therefore the butt of the joke. An alternative possibility is that Phizog is a reference to Dickens' later illustrator whose pseudonym was Phiz. It is also just conceivable that the young boy is Marks's own young son, Jacob. The print can be placed in the context of a scatological English vernacular humour that extends from Shakespeare through to Donald McGill and into the present day.

  14. Cued Dichotic Listening with Right-Handed, Left-Handed, Bilingual and Learning-Disabled Children.

    ERIC Educational Resources Information Center

    Obrzut, John E.; And Others

    This study used cued dichotic listening to investigate differences in language lateralization among right-handed (control), left handed, bilingual, and learning disabled children. Subjects (N=60) ranging in age from 7-13 years were administered a consonant-vowel-consonant dichotic paradigm with three experimental conditions (free recall, directed…

  15. A Left-Hand Rule for Faraday's Law

    ERIC Educational Resources Information Center

    Salu, Yehuda

    2014-01-01

    A left-hand rule for Faraday's law is presented here. This rule provides a simple and quick way of finding directional relationships between variables of Faraday's law without using Lenz's rule.

  16. SiGe BiCMOS balanced transmission line based on coplanar waveguide and split ring resonator

    NASA Astrophysics Data System (ADS)

    Serrano, Enrique; Borja, Alejandro L.; Boccia, Luigi; Cascon, Joaquin; Ibrahim, Safwat; Calzona, D.; Amendola, G.

    2016-06-01

    In this work, the design of a right-/left-handed composite transmission line implementation with passband characteristics is demonstrated on 0.13 µm silicon-germanium bipolar CMOS (SiGe BiCMOS) technology. The proposed structure is formed by a shorted coplanar waveguide transmission line loaded with split ring resonators (SRRs). As it will be shown, by controlling the geometry of the SRRs as well as their electric coupling with the host line, it is possible to achieve a balanced passband response with widespread bandwidth at millimeter wave frequencies. Besides, this paper introduces a configuration that allows to significantly lower the resonant frequency of the SRRs by loading the rings with Metal-Insulator-Metal capacitors. It will be illustrated how this approach allows to reduce the center band frequency of about 40% preserving the balanced behavior and without increasing the resonator size. Finally, the proposed design was experimentally validated with a prototype exhibiting an extended passband with a fractional bandwidth of 19.3% and -3.2 dB of insertion loss around the central frequency of 60 GHz. The use of these transmission lines can be foreseeing in high-capacity millimeter wave communication systems which require compact passband blocks integrated on chip.

  17. Nonreciprocal and magnetically scanned miniaturized leaky-wave antennas using coupled transmission lines

    NASA Astrophysics Data System (ADS)

    Apaydin, Nil; Sertel, Kubilay; Volakis, John L.

    2014-06-01

    This paper presents a new class of magnetically scanned leaky wave antennas (LWAs), incorporating ferrite (or possibly magnetoelectric composite), for wide angle beamsteering. Using the ferrite's tunable permeability beamsteering is achieved by controlling the external bias field. This is unlike most leaky-wave antennas requiring frequency modulation to steer the beam. Our first design is based on coupled microstrip lines on a biased ferrite substrate with nonreciprocal radiation properties, specifically a 5 dB contrast between the measured transmit and receive gain in the E-plane was achieved. However, it was found that inhomogeneities in the bias field limited its scanning performance. To alleviate this issue, a new class of miniaturized metamaterial based LWA was considered and presented here. This new design is based on coupled composite right left handed (CRLH) transmission lines (TLs) and has a unit-cell length of only λ0/20. For validation, a 15-unit-cell prototype was manufactured and its TX/RX beams were scanned in the E-plane 80° by changing the bias field within a range of ±50 Oe. We found that the associated antenna gain varied between 3.5 dB and 5 dB at 1.79 GHz as the beam was scanned. In the above design, scanning was realized by changing the distance between the bias source and the LWA. Thus, future work will be focused on LWAs tuned by biasing a magnetodielectric layer placed below the ferrite substrate.

  18. Dispersion-free radial transmission lines

    DOEpatents

    Caporaso, George J.; Nelson, Scott D.

    2011-04-12

    A dispersion-free radial transmission line ("DFRTL") preferably for linear accelerators, having two plane conductors each with a central hole, and an electromagnetically permeable material ("EPM") between the two conductors and surrounding a channel connecting the two holes. At least one of the material parameters of relative magnetic permeability, relative dielectric permittivity, and axial width of the EPM is varied as a function of radius, so that the characteristic impedance of the DFRTL is held substantially constant, and pulse transmission therethrough is substantially dispersion-free. Preferably, the EPM is divided into concentric radial sections, with the varied material parameters held constant in each respective section but stepwise varied between sections as a step function of the radius. The radial widths of the concentric sections are selected so that pulse traversal time across each section is the same, and the varied material parameters of the concentric sections are selected to minimize traversal error.

  19. View facing north, Structure 162 in foreground, as Transmission Line ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing north, Structure 16-2 in foreground, as Transmission Line turns at intersection of Powerline Road and US 87 - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  20. View facing south, near Structure 515, of Transmission Line rising ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing south, near Structure 51-5, of Transmission Line rising out of Marias River Valley - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  1. 3. DETAIL, LIGHTNING ARRESTER ON SAR TRANSMISSION LINE. EEC print ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. DETAIL, LIGHTNING ARRESTER ON SAR TRANSMISSION LINE. EEC print no. S-C-01-00478, no date. Photographer unknown. - Santa Ana River Hydroelectric System, Transmission Lines, Redlands, San Bernardino County, CA

  2. Transmission line including support means with barriers

    DOEpatents

    Cookson, Alan H.

    1982-01-01

    A gas insulated transmission line includes an elongated outer sheath, a plurality of inner conductors disposed within and extending along the outer sheath, and an insulating gas which electrically insulates the inner conductors from the outer sheath. A support insulator insulatably supports the inner conductors within the outer sheath, with the support insulator comprising a main body portion including a plurality of legs extending to the outer sheath, and barrier portions which extend between the legs. The barrier portions have openings therein adjacent the main body portion through which the inner conductors extend.

  3. Transmission line icing measurement on photogrammetry method

    NASA Astrophysics Data System (ADS)

    Huang, Huan; Ma, Xiaohong; Zhao, Lijin; Du, Hao; Luo, Hong; Mao, Xianyin; Tang, Min; Liu, Yawen

    2015-12-01

    Icing thickness parameter is the basic data for power sector to make decision for icing accident prevention. In this paper, a transmission line icing measurement method is proposed. It used the photogrammetry method to realize icing parameters measurement through the integration of high resolution camera, laser range finder and inertial measurement unit. Compared with traditional icing measurement method, this method is flexible and is the effective supplement of the fixed icing detection terminal. And its high accuracy measurement guarantees the reliability of the icing thickness parameters.

  4. SMILE transmission line adder for RADLAC II

    SciTech Connect

    Mazarakis, M.G.; Poukey, J.W.; Shope, S.L.; Frost, C.A.; Turman, B.N.; Ramirez, J.J.; Prestwich, K.R.; Pankuch, P.J.

    1991-12-31

    SMILE is a coaxial Self Magnetically Insulated Transmission Line voltage adder. It replaces the original beam line of the RADLAC II accelerator by a 12.5 m long cathode electrode. The anode electrode remains practically the same, consisting of the original eight insulating stacks or feeds which are connected with equal diameter stainless steel cylinders. The beam is produced at the end of the accelerator and is free of all the possible instabilities associated with accelerating gaps and magnetic vacuum transport. Annular beams with {beta}{perpendicular} {le} 0.1 and radius r{sub b} {le} 1 cm were routinely obtained and extracted from a small magnetically-immersed foilless electron diode. Results of the experimental evaluation are presented and compared with design parameters and numerical simulation predictions. 4 refs.

  5. SMILE transmission line adder for RADLAC II

    SciTech Connect

    Mazarakis, M.G.; Poukey, J.W.; Shope, S.L.; Frost, C.A.; Turman, B.N.; Ramirez, J.J.; Prestwich, K.R. ); Pankuch, P.J. . Special Projects)

    1991-01-01

    SMILE is a coaxial Self Magnetically Insulated Transmission Line voltage adder. It replaces the original beam line of the RADLAC II accelerator by a 12.5 m long cathode electrode. The anode electrode remains practically the same, consisting of the original eight insulating stacks or feeds which are connected with equal diameter stainless steel cylinders. The beam is produced at the end of the accelerator and is free of all the possible instabilities associated with accelerating gaps and magnetic vacuum transport. Annular beams with {beta}{perpendicular} {le} 0.1 and radius r{sub b} {le} 1 cm were routinely obtained and extracted from a small magnetically-immersed foilless electron diode. Results of the experimental evaluation are presented and compared with design parameters and numerical simulation predictions. 4 refs.

  6. Giant vacuum forces via transmission lines

    PubMed Central

    Shahmoon, Ephraim; Mazets, Igor; Kurizki, Gershon

    2014-01-01

    Quantum electromagnetic fluctuations induce forces between neutral particles, known as the van der Waals and Casimir interactions. These fundamental forces, mediated by virtual photons from the vacuum, play an important role in basic physics and chemistry and in emerging technologies involving, e.g., microelectromechanical systems or quantum information processing. Here we show that these interactions can be enhanced by many orders of magnitude upon changing the character of the mediating vacuum modes. By considering two polarizable particles in the vicinity of any standard electric transmission line, along which photons can propagate in one dimension, we find a much stronger and longer-range interaction than in free space. This enhancement may have profound implications on many-particle and bulk systems and impact the quantum technologies mentioned above. The predicted giant vacuum force is estimated to be measurable in a coplanar waveguide line. PMID:25002503

  7. 49 CFR 192.719 - Transmission lines: Testing of repairs.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Testing of repairs. 192.719... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.719 Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line...

  8. 49 CFR 192.745 - Valve maintenance: Transmission lines.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Valve maintenance: Transmission lines. 192.745... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.745 Valve maintenance: Transmission lines. (a) Each transmission line valve that might be required during any...

  9. 49 CFR 192.745 - Valve maintenance: Transmission lines.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Valve maintenance: Transmission lines. 192.745... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.745 Valve maintenance: Transmission lines. (a) Each transmission line valve that might be required during any...

  10. 49 CFR 192.179 - Transmission line valves.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission line valves. 192.179 Section 192.179... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing...

  11. 49 CFR 192.179 - Transmission line valves.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission line valves. 192.179 Section 192.179... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Design of Pipeline Components § 192.179 Transmission line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing...

  12. 32 CFR 644.431 - Power transmission lines.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 32 National Defense 4 2012-07-01 2011-07-01 true Power transmission lines. 644.431 Section 644.431... transmission lines. (a) Authority. Pursuant to the provisions of section 13(d) of the Surplus Property Act of... transmission line and the right of way acquired for its construction is needed for or adaptable to...

  13. 32 CFR 644.431 - Power transmission lines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 32 National Defense 4 2014-07-01 2013-07-01 true Power transmission lines. 644.431 Section 644.431... transmission lines. (a) Authority. Pursuant to the provisions of section 13(d) of the Surplus Property Act of... transmission line and the right of way acquired for its construction is needed for or adaptable to...

  14. 49 CFR 192.745 - Valve maintenance: Transmission lines.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Valve maintenance: Transmission lines. 192.745 Section 192.745 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... maintenance: Transmission lines. (a) Each transmission line valve that might be required during any...

  15. 49 CFR 192.719 - Transmission lines: Testing of repairs.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission lines: Testing of repairs. 192.719 Section 192.719 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line...

  16. 49 CFR 192.745 - Valve maintenance: Transmission lines.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Valve maintenance: Transmission lines. 192.745 Section 192.745 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... maintenance: Transmission lines. (a) Each transmission line valve that might be required during any...

  17. 32 CFR 644.431 - Power transmission lines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 32 National Defense 4 2013-07-01 2013-07-01 false Power transmission lines. 644.431 Section 644... Power transmission lines. (a) Authority. Pursuant to the provisions of section 13(d) of the Surplus... power transmission line and the right of way acquired for its construction is needed for or adaptable...

  18. 49 CFR 192.719 - Transmission lines: Testing of repairs.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Testing of repairs. 192.719 Section 192.719 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line...

  19. 49 CFR 192.719 - Transmission lines: Testing of repairs.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission lines: Testing of repairs. 192.719 Section 192.719 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line...

  20. 49 CFR 192.719 - Transmission lines: Testing of repairs.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Testing of repairs. 192.719 Section 192.719 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Testing of repairs. (a) Testing of replacement pipe. If a segment of transmission line...

  1. 49 CFR 192.745 - Valve maintenance: Transmission lines.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Valve maintenance: Transmission lines. 192.745 Section 192.745 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... maintenance: Transmission lines. (a) Each transmission line valve that might be required during any...

  2. 32 CFR 644.431 - Power transmission lines.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Power transmission lines. 644.431 Section 644.431... transmission lines. (a) Authority. Pursuant to the provisions of section 13(d) of the Surplus Property Act of... transmission line and the right of way acquired for its construction is needed for or adaptable to...

  3. 49 CFR 192.706 - Transmission lines: Leakage surveys.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission lines: Leakage surveys. 192.706... Transmission lines: Leakage surveys. Leakage surveys of a transmission line must be conducted at intervals not... transports gas in conformity with § 192.625 without an odor or odorant, leakage surveys using leak...

  4. 49 CFR 192.706 - Transmission lines: Leakage surveys.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission lines: Leakage surveys. 192.706... Transmission lines: Leakage surveys. Leakage surveys of a transmission line must be conducted at intervals not... transports gas in conformity with § 192.625 without an odor or odorant, leakage surveys using leak...

  5. 49 CFR 192.706 - Transmission lines: Leakage surveys.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Leakage surveys. 192.706... Transmission lines: Leakage surveys. Leakage surveys of a transmission line must be conducted at intervals not... transports gas in conformity with § 192.625 without an odor or odorant, leakage surveys using leak...

  6. 49 CFR 192.706 - Transmission lines: Leakage surveys.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Leakage surveys. 192.706... Transmission lines: Leakage surveys. Leakage surveys of a transmission line must be conducted at intervals not... transports gas in conformity with § 192.625 without an odor or odorant, leakage surveys using leak...

  7. 32 CFR 644.431 - Power transmission lines.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 4 2011-07-01 2011-07-01 false Power transmission lines. 644.431 Section 644... Power transmission lines. (a) Authority. Pursuant to the provisions of section 13(d) of the Surplus... power transmission line and the right of way acquired for its construction is needed for or adaptable...

  8. A radial transmission line material measurement apparatus

    SciTech Connect

    Warne, L.K.; Moyer, R.D.; Koontz, T.E.; Morris, M.E.

    1993-05-01

    A radial transmission line material measurement sample apparatus (sample holder, offset short standards, measurement software, and instrumentation) is described which has been proposed, analyzed, designed, constructed, and tested. The purpose of the apparatus is to obtain accurate surface impedance measurements of lossy, possibly anisotropic, samples at low and intermediate frequencies (vhf and low uhf). The samples typically take the form of sections of the material coatings on conducting objects. Such measurements thus provide the key input data for predictive numerical scattering codes. Prediction of the sample surface impedance from the coaxial input impedance measurement is carried out by two techniques. The first is an analytical model for the coaxial-to-radial transmission line junction. The second is an empirical determination of the bilinear transformation model of the junction by the measurement of three full standards. The standards take the form of three offset shorts (and an additional lossy Salisbury load), which have also been constructed. The accuracy achievable with the device appears to be near one percent.

  9. Observation of Wakefield Generation in Left-Handed Band of Metamaterial-Loaded Waveguide

    SciTech Connect

    Antipov, S.; Spentzouris, L.; Liu, W.; Gai, W.; Power, J. G.

    2009-01-22

    We report on a design of a TM-mode based metamaterial-loaded waveguide. Network analyzer measurements demonstrated a left-handed propagation region for the TM11 mode at around 10 GHz. A beamline experiment was performed with the metamaterial-loaded waveguide. In this experiment, a 6 MeV electron beam passes through the waveguide and generates a wakefield, via the Cherenkov radiation mechanism. We detected a signal in the left-handed frequency band at 10 GHz. This is an indirect demonstration of reverse Cherenkov radiation as discussed in several papers. Cherenkov radiation in artificially constructed materials (metamaterials, MTM) can provide unusual, engineered features that can be advantageous for particle detector design.

  10. Normal-incidence left-handed metamaterials based on symmetrically connected split-ring resonators.

    PubMed

    Wang, Jiafu; Qu, Shaobo; Xu, Zhuo; Ma, Hua; Xia, Song; Yang, Yiming; Wu, Xiang; Wang, Qian; Chen, Chunhui

    2010-03-01

    Normal-incidence left-handed metamaterials (LHMs) based on symmetrically connected split-ring resonators (SC-SRRs) were proposed and investigated numerically and experimentally. The SC-SRR, which can be easily fabricated by conventional printed circuit board technology, is composed of metallic patterns connected by metalized vias through the dielectric substrate. Under normal incidence, SC-SRR exhibits strong magnetic response, leading to negative permeability. By combing SC-SRRs with metallic wires, a normal-incidence LHM was realized. Both the simulation and experiment results demonstrated left-handed properties of the SC-SRR/wire LHM. The design method paved new ways of realizing magnetic and even electric metamaterials.

  11. Why a harmonic solution for lossless, perfectly homogeneous, left-handed material cannot exist.

    PubMed

    Maystre, Daniel; Enoch, Stefan; McPhedran, Ross

    2008-08-01

    In a preceding paper [J. Opt. Soc. Am. A21, 122 (2004)], we proposed proof of the nonexistence of harmonic solutions for a perfectly homogeneous left-handed material with both relative permittivity and relative permeability equal to -1 using the theorem of analytic continuation of an analytic function. The use of this theorem of analyticity has been questioned in a recent paper [Phys. Rev. E73, 046608 (2006)], arguing the possible inadequacy of the conditions of application of the theorem. We avoid the use of the analyticity theorem and propose a direct and simple proof of the nonexistence of such solutions. Furthermore, this proof is extended to any left-handed material with negative permeability and permittivity.

  12. Genuine effectively biaxial left-handed metamaterials due to extreme coupling.

    PubMed

    Menzel, Christoph; Alaee, Rasoul; Pshenay-Severin, Ekaterina; Helgert, Christian; Chipouline, Arkadi; Rockstuhl, Carsten; Pertsch, Thomas; Lederer, Falk

    2012-02-15

    Most left-handed metamaterials cannot be described by local effective permittivity or permeability tensors in the visible or near-infrared due to the mesoscopic size of the respective unit cells and the related strong spatial dispersion. We lift this problem and propose a metamaterial exhibiting artificial magnetism that does not suffer from this restriction. The artificial magnetism arises from the extreme coupling between both metallic films forming the unit cell. We show that its electromagnetic response can be properly described by biaxial local constitutive relations. A genuine biaxial left-handed fishnet metamaterial is suggested, which can be realized by atomic layer deposition to fabricate the nanoscaled spacing layers required for extreme coupling.

  13. Neuromotor performance of normally developing left-handed children and adolescents.

    PubMed

    Rousson, Valentin; Gasser, Theo; Caflisch, Jon; Jenni, Oskar G

    2009-12-01

    Neuromotor functioning - i.e., timed performance and quality of movements - was examined in 66 left-handed children and adolescents between 5 and 18.5 years by means of the Zurich Neuromotor Assessment. Quality of movements was assessed by the degree and the frequency of associated movements. Results were compared to normative data from 593 right-handers. The overall scores for timed motor performance were similar for left-handers and right-handers, while left-handers had more associated movements than right-handers with both sides. In agreement with previous studies in adults, we found that left-handed children were less lateralized than right-handers. They performed faster with their non-dominant side and slower with their dominant side. This finding was roughly independent of age, which may indicate that handedness does not reflect long-term effects of previous motor experience, but may be primarily attributed to genetic factors.

  14. [The comparison of characteristics of smooth pursuit in left-handed and right-handed persons].

    PubMed

    Bozhkova, V P; Surovicheva, N S; Nikolaev, D P

    2010-01-01

    The estimation of the smooth pursuit efficiency in healthy young adults by method based on stroboscopic stimulation is given. The influence of manual function asymmetry on smooth pursuit was tested. Subjects were classified as left-handed or right-handed under a well known handedness questionnaire of Annett supplemented by Luria's tests. It was shown that the strong right-handed persons have a high quality of smooth pursuit of stimuli moving horizontally in rightward and leftward directions with the velocities 20 degrees/s and 25 degrees/s. Left-handed persons track similar stimuli, on the average, worse than the strong right-handed ones. It haven't been observed the influence of manual function asymmetry on the dependence of the smooth pursuit efficiency from the moving stimuli direction (left to right or right to left).

  15. Structure of the fully modified left-handed cyclohexene nucleic acid sequence GTGTACAC.

    PubMed

    Robeyns, Koen; Herdewijn, Piet; Van Meervelt, Luc

    2008-02-13

    CeNA oligonucleotides consist of a phosphorylated backbone where the deoxyribose sugars are replaced by cyclohexene moieties. The X-ray structure determination and analysis of a fully modified octamer sequence GTGTACAC, which is the first crystal structure of a carbocyclic-based nucleic acid, is presented. This particular sequence was built with left-handed building blocks and crystallizes as a left-handed double helix. The helix can be characterized as belonging to the (mirrored) A-type family. Crystallographic data were processed up to 1.53 A, and the octamer sequence crystallizes in the space group R32. The sugar puckering is found to adopt the 3H2 half-chair conformation which mimics the C3'-endo conformation of the ribose sugar. The double helices stack on top of each other to form continuous helices, and static disorder is observed due to this end-to-end stacking.

  16. Unprecedented right- and left-handed quadruplex structures formed by heterochiral oligodeoxyribonucleotides.

    PubMed

    Virgilio, Antonella; Esposito, Veronica; Citarella, Giuseppe; Mangoni, Alfonso; Mayol, Luciano; Galeone, Aldo

    2011-07-01

    CD and NMR studies on heterochiral oligodeoxynucleotides (d/l-ODNs) forming quadruplex structures are reported. Heterochiral ODNs, based on sequence TGGGGT, are able to form stable either right- or left-handed quadruplexes depending on d/l ratio and residues position. Results suggest that the 3'-end and the core of the G-run are more important than the 5'-end in determining the quadruplex handness. Particularly, oligonucleotide T(D)G(D)G(L)G(L)G(D)T(D) (L34) at low temperatures forms a well-defined left-handed quadruplex, notwithstanding it is mostly composed by natural d residues. This structure is characterized by three all-anti G-tetrads and one all-syn G-tetrad.

  17. Two-Dimensional Simulation of Left-Handed Metamaterial Flat Lens Using Remcon XFDTD

    NASA Technical Reports Server (NTRS)

    Wilson, Jeffrey D.; Reinert, Jason M.

    2006-01-01

    Remcom's XFDTD software was used to model the properties of a two-dimensional left-handed metamaterial (LHM) flat lens. The focusing capability and attenuation of the material were examined. The results showed strong agreement with experimental results and theoretical predictions of focusing effects and focal length. The inherent attenuation in the model corresponds well with the experimental results and implies that the code does a reasonably accurate job of modeling the actual metamaterial.

  18. 45. 800 H.P. WATER WHEEL UNIT (LEFT HAND) DIRECT CONNECTED ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    45. 800 H.P. WATER WHEEL UNIT (LEFT HAND) DIRECT CONNECTED TO A 500 K.W. G.E. CO. GENERATOR, SPEED 176 R.P.M., HEAD OF WATER 305 FT EFF., FOR SANTA ANA RIVER NO. 2 PLANT. ABNER DOBLE CO., ENGINEERS, SAN FRANCISCO, AUG. 29, 1904. TRACED FROM DOBLE BLUE PRINT, SEPT. 9, 1911. SCE drawing no. 5698. - Santa Ana River Hydroelectric System, SAR-2 Powerhouse, Redlands, San Bernardino County, CA

  19. Left-handed metamaterials operating in the visible: negative refraction and negative radiation pressure

    NASA Astrophysics Data System (ADS)

    Lezec, Henri

    2009-03-01

    Forty years ago, V. Veselago derived the electromagnetic properties of a hypothetical material having simultaneously-negative values of electric permittivity and magnetic permeability [1]. Such a material, denominated ``left-handed'', was predicted to exhibit a negative index of refraction, as well as a number of other counter-intuitive optical properties. For example, it was hypothesized that a perfect mirror illuminated with a plane wave would experience a negative radiation pressure (pull) when immersed in a left-handed medium, as opposed to the usual positive radiation pressure experienced when facing a dielectric medium such as air or glass. Since left-handed materials are not available in nature, considerable efforts are currently under way to implement them under the form of artificial ``metamaterials'' -- composite media with tailored bulk optical characteristics resulting from constituent structures which are smaller in both size and density than the effective wavelength in the medium. Here we show how surface-plasmon modes propagating in a stacked array of metal-insulator-metal (MIM) waveguides can be harnessed to yield a volumetric left-handed metamaterial characterized by an in-plane-isotropic negative index of refraction over a broad frequency range spanning the blue and green. By sculpting this material with a focused-ion beam we realize prisms and micro-cantilevers which we use to demonstrate, for the first time, (a) in-plane isotropic negative-refraction at optical frequencies, and (b) negative radiation pressure. We predict and experimentally verify a negative ``superpressure'', the magnitude of which exceeds the photon pressure experienced by a perfect mirror by more than a factor of two. 1) V. Veselago, Sov. Phys. Usp. 10, p.509 (1968).

  20. Fabrication of left-handed metal microcoil from spiral vessel of vascular plant.

    PubMed

    Kamata, Kaori; Suzuki, Soichiro; Ohtsuka, Masayuki; Nakagawa, Masaru; Iyoda, Tomokazu; Yamada, Atsushi

    2011-12-01

    Silver microcoil is fabricated through a biotemplating process combined with electroless plating. Spiral vessels in Lotus root are employed as a biotemplate because of their left-handed coil structure. The silver microcoil exhibits a solenoidal microcoil showing self-inductance in the level of picohenry, which could be applied for electromagnetic-responsive materials in the high-frequency region such as millimeter waves or terahertz waves.

  1. Left-handed cardiac surgery: tips from set up to closure for trainees and their trainers.

    PubMed

    Burdett, Clare; Dunning, Joel; Goodwin, Andrew; Theakston, Maureen; Kendall, Simon

    2016-09-01

    There are certain obstacles which left-handed surgeons can face when training but these are not necessary and often perpetuated by a lack of knowledge. Most have been encountered and overcome at some point but unless recorded and disseminated they will have to be resolved repeatedly by each trainee and their trainers. This article highlights difficulties that the left-hander may encounter in cardiac surgery and gives practical operative advice for both trainees and their trainers to help overcome them.

  2. 77 FR 24264 - Notice of Receipt of Petition for Decision That Nonconforming Left-Hand Drive 2006 Land Rover...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-04-23

    ... in the Federal Register published on April 11, 2000 (65 FR 19477-78). How to Read Comments submitted... Nonconforming Left-Hand Drive 2006 Land Rover Range Rover Multi-Purpose Passenger Vehicles Manufactured Prior to... Traffic Safety Administration (NHTSA) of a petition for a decision that left-hand drive (LHD) 2006...

  3. Reduced asymmetry in motor skill learning in left-handed compared to right-handed individuals.

    PubMed

    McGrath, Robert L; Kantak, Shailesh S

    2016-02-01

    Hemispheric specialization for motor control influences how individuals perform and adapt to goal-directed movements. In contrast to adaptation, motor skill learning involves a process wherein one learns to synthesize novel movement capabilities in absence of perturbation such that they are performed with greater accuracy, consistency and efficiency. Here, we investigated manual asymmetry in acquisition and retention of a complex motor skill that requires speed and accuracy for optimal performance in right-handed and left-handed individuals. We further determined if degree of handedness influences motor skill learning. Ten right-handed (RH) and 10 left-handed (LH) adults practiced two distinct motor skills with their dominant or nondominant arms during separate sessions two-four weeks apart. Learning was quantified by changes in the speed-accuracy tradeoff function measured at baseline and one-day retention. Manual asymmetry was evident in the RH group but not the LH group. RH group demonstrated significantly greater skill improvement for their dominant-right hand than their nondominant-left hand. In contrast, for the LH group, both dominant and nondominant hands demonstrated comparable learning. Less strongly-LH individuals (lower EHI scores) exhibited more learning of their dominant hand. These results suggest that while hemispheric specialization influences motor skill learning, these effects may be influenced by handedness. PMID:26638046

  4. A sinister plot? Facts, beliefs, and stereotypes about the left-handed personality.

    PubMed

    Grimshaw, Gina M; Wilson, Marc S

    2013-01-01

    Is there a left-handed personality? Is there a left-handed stereotype? Although psychologists have enthusiastically compared left- and right-handers across myriad cognitive, behavioural, and neuropsychological domains, there has been very little empirical investigation of the relationship between handedness and personality. In Study 1 we assessed the Big 5 personality traits (extraversion, agreeableness, conscientiousness, emotionality, and openness to experience) in a sample of 662 young adults in New Zealand. Left- and right-handers did not differ on any factor. However, there was a curvilinear relationship between hand preference and extraversion; mixed-handers were more introverted than either left- or right-handers. This finding is consistent with other research indicating that degree may be of more psychological consequence than direction of handedness. In Study 2 we assessed beliefs and stereotypes about the left-handed personality. Both left- and right-handers shared the belief that left-handers are more introverted and open to experience than right-handers. This stereotype is not negative, and argues against the status of left-handers as a stigmatised group in modern Western culture.

  5. Reduced asymmetry in motor skill learning in left-handed compared to right-handed individuals.

    PubMed

    McGrath, Robert L; Kantak, Shailesh S

    2016-02-01

    Hemispheric specialization for motor control influences how individuals perform and adapt to goal-directed movements. In contrast to adaptation, motor skill learning involves a process wherein one learns to synthesize novel movement capabilities in absence of perturbation such that they are performed with greater accuracy, consistency and efficiency. Here, we investigated manual asymmetry in acquisition and retention of a complex motor skill that requires speed and accuracy for optimal performance in right-handed and left-handed individuals. We further determined if degree of handedness influences motor skill learning. Ten right-handed (RH) and 10 left-handed (LH) adults practiced two distinct motor skills with their dominant or nondominant arms during separate sessions two-four weeks apart. Learning was quantified by changes in the speed-accuracy tradeoff function measured at baseline and one-day retention. Manual asymmetry was evident in the RH group but not the LH group. RH group demonstrated significantly greater skill improvement for their dominant-right hand than their nondominant-left hand. In contrast, for the LH group, both dominant and nondominant hands demonstrated comparable learning. Less strongly-LH individuals (lower EHI scores) exhibited more learning of their dominant hand. These results suggest that while hemispheric specialization influences motor skill learning, these effects may be influenced by handedness.

  6. Method for bonding a transmission line to a downhole tool

    SciTech Connect

    Hall, David R.; Fox, Joe

    2007-11-06

    An apparatus for bonding a transmission line to the central bore of a downhole tool includes a pre-formed interface for bonding a transmission line to the inside diameter of a downhole tool. The pre-formed interface includes a first surface that substantially conforms to the outside contour of a transmission line and a second surface that substantially conforms to the inside diameter of a downhole tool. In another aspect of the invention, a method for bonding a transmission line to the inside diameter of a downhole tool includes positioning a transmission line near the inside wall of a downhole tool and placing a mold near the transmission line and the inside wall. The method further includes injecting a bonding material into the mold and curing the bonding material such that the bonding material bonds the transmission line to the inside wall.

  7. Tendon and ligament fibrillar crimps give rise to left-handed helices of collagen fibrils in both planar and helical crimps.

    PubMed

    Franchi, Marco; Ottani, Vittoria; Stagni, Rita; Ruggeri, Alessandro

    2010-03-01

    Collagen fibres in tendons and ligaments run straight but in some regions they show crimps which disappear or appear more flattened during the initial elongation of tissues. Each crimp is formed of collagen fibrils showing knots or fibrillar crimps at the crimp top angle. The present study analyzes by polarized light microscopy, scanning electron microscopy, transmission electron microscopy the 3D morphology of fibrillar crimp in tendons and ligaments of rat demonstrating that each fibril in the fibrillar region always twists leftwards changing the plane of running and sharply bends modifying the course on a new plane. The morphology of fibrillar crimp in stretched tendons fulfills the mechanical role of the fibrillar crimp acting as a particular knot/biological hinge in absorbing tension forces during fibril strengthening and recoiling collagen fibres when stretching is removed. The left-handed path of fibrils in the fibrillar crimp region gives rise to left-handed fibril helices observed both in isolated fibrils and sections of different tendons and ligaments (flexor digitorum profundus muscle tendon, Achilles tendon, tail tendon, patellar ligament and medial collateral ligament of the knee). The left-handed path of fibrils represents a new final suprafibrillar level of the alternating handedness which was previously described only from the molecular to the microfibrillar level. When the width of the twisting angle in the fibrillar crimp is nearly 180 degrees the fibrils appear as left-handed flattened helices forming crimped collagen fibres previously described as planar crimps. When fibrils twist with different subsequent rotational angles (< 180 degrees ) they always assume a left-helical course but, running in many different nonplanar planes, they form wider helical crimped fibres.

  8. Nonlinear transmission line based electron beam driver

    SciTech Connect

    French, David M.; Hoff, Brad W.; Tang Wilkin; Heidger, Susan; Shiffler, Don; Allen-Flowers, Jordan

    2012-12-15

    Gated field emission cathodes can provide short electron pulses without the requirement of laser systems or cathode heating required by photoemission or thermionic cathodes. The large electric field requirement for field emission to take place can be achieved by using a high aspect ratio cathode with a large field enhancement factor which reduces the voltage requirement for emission. In this paper, a cathode gate driver based on the output pulse train from a nonlinear transmission line is experimentally demonstrated. The application of the pulse train to a tufted carbon fiber field emission cathode generates short electron pulses. The pulses are approximately 2 ns in duration with emission currents of several mA, and the train contains up to 6 pulses at a frequency of 100 MHz. Particle-in-cell simulation is used to predict the characteristic of the current pulse train generated from a single carbon fiber field emission cathode using the same technique.

  9. Networks of nonlinear superconducting transmission line resonators

    NASA Astrophysics Data System (ADS)

    Leib, M.; Deppe, F.; Marx, A.; Gross, R.; Hartmann, M. J.

    2012-07-01

    We investigate a network of coupled superconducting transmission line resonators, each of them made nonlinear with a capacitively shunted Josephson junction coupling to the odd flux modes of the resonator. The resulting eigenmode spectrum shows anticrossings between the plasma mode of the shunted junction and the odd resonator modes. Notably, we find that the combined device can inherit the complete nonlinearity of the junction, allowing for a description as a harmonic oscillator with a Kerr nonlinearity. Using a dc SQUID instead of a single junction, the nonlinearity can be tuned between 10 kHz and 4 MHz while maintaining resonance frequencies of a few gigahertz for realistic device parameters. An array of such nonlinear resonators can be considered a scalable superconducting quantum simulator for a Bose-Hubbard Hamiltonian. The device would be capable of accessing the strongly correlated regime and be particularly well suited for investigating quantum many-body dynamics of interacting particles under the influence of drive and dissipation.

  10. 49 CFR 192.705 - Transmission lines: Patrolling.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Patrolling. 192.705 Section... NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.705 Transmission... adjacent to the transmission line right-of-way for indications of leaks, construction activity, and...

  11. 49 CFR 192.709 - Transmission lines: Record keeping.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Record keeping. 192.709... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.709 Transmission lines: Record keeping. Each operator shall maintain the following records for transmission...

  12. 49 CFR 192.709 - Transmission lines: Record keeping.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Record keeping. 192.709 Section 192.709 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Record keeping. Each operator shall maintain the following records for transmission...

  13. 7 CFR 1726.77 - Substation and transmission line construction.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Substation and transmission line construction. 1726... UTILITIES SERVICE, DEPARTMENT OF AGRICULTURE ELECTRIC SYSTEM CONSTRUCTION POLICIES AND PROCEDURES Substation and Transmission Facilities § 1726.77 Substation and transmission line construction. (a)...

  14. 49 CFR 192.709 - Transmission lines: Record keeping.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission lines: Record keeping. 192.709 Section 192.709 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Record keeping. Each operator shall maintain the following records for transmission...

  15. 49 CFR 192.705 - Transmission lines: Patrolling.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Transmission lines: Patrolling. 192.705 Section... NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.705 Transmission... adjacent to the transmission line right-of-way for indications of leaks, construction activity, and...

  16. 49 CFR 192.709 - Transmission lines: Record keeping.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Record keeping. 192.709 Section 192.709 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Record keeping. Each operator shall maintain the following records for transmission...

  17. 49 CFR 192.709 - Transmission lines: Record keeping.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission lines: Record keeping. 192.709 Section 192.709 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND... Transmission lines: Record keeping. Each operator shall maintain the following records for transmission...

  18. 49 CFR 192.705 - Transmission lines: Patrolling.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Transmission lines: Patrolling. 192.705 Section... NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.705 Transmission... adjacent to the transmission line right-of-way for indications of leaks, construction activity, and...

  19. 49 CFR 192.705 - Transmission lines: Patrolling.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Patrolling. 192.705 Section... NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.705 Transmission... adjacent to the transmission line right-of-way for indications of leaks, construction activity, and...

  20. 49 CFR 192.705 - Transmission lines: Patrolling.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Patrolling. 192.705 Section... lines: Patrolling. (a) Each operator shall have a patrol program to observe surface conditions on and adjacent to the transmission line right-of-way for indications of leaks, construction activity, and...

  1. 49 CFR 192.179 - Transmission line valves.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission line valves. 192.179 Section 192.179... line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing block valves spaced as follows, unless in a particular case the Administrator finds that alternative...

  2. 49 CFR 192.179 - Transmission line valves.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... be equipped with valves or other components to shut off the flow of gas to an offshore platform in an... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission line valves. 192.179 Section 192.179... line valves. (a) Each transmission line, other than offshore segments, must have sectionalizing...

  3. Big Creek Hydroelectric System, East & West Transmission Line, 241mile ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Big Creek Hydroelectric System, East & West Transmission Line, 241-mile transmission corridor extending between the Big Creek Hydroelectric System in the Sierra National Forest in Fresno County and the Eagle Rock Substation in Los Angeles, California, Visalia, Tulare County, CA

  4. 49 CFR 192.707 - Line markers for mains and transmission lines.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Line markers for mains and transmission lines. 192... § 192.707 Line markers for mains and transmission lines. (a) Buried pipelines. Except as provided in paragraph (b) of this section, a line marker must be placed and maintained as close as practical over...

  5. 49 CFR 192.707 - Line markers for mains and transmission lines.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Line markers for mains and transmission lines. 192... § 192.707 Line markers for mains and transmission lines. (a) Buried pipelines. Except as provided in paragraph (b) of this section, a line marker must be placed and maintained as close as practical over...

  6. 49 CFR 192.707 - Line markers for mains and transmission lines.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Line markers for mains and transmission lines. 192... § 192.707 Line markers for mains and transmission lines. (a) Buried pipelines. Except as provided in paragraph (b) of this section, a line marker must be placed and maintained as close as practical over...

  7. Radio frequency communication system utilizing radiating transmission lines

    DOEpatents

    Struven, Warren C.

    1984-01-01

    A radio communication system for use in tunnels, mines, buildings or other shielded locations in which a pair of radiating transmission lines (30), (31) extend through such location in spaced coextensive relation to each other. Each transmission line (30), (31) has at least one unidirectional amplifier (32), (33) interposed therein with the sense of the unidirectional amplifier (32) of one transmission line (30) being opposite to the sense of the unidirectional amplifier (33) of the other transmission line (31). Each of the amplifiers (32), (33) has a gain which is less than the coupling loss between the transmission lines (30), (31). Two or more mobile transceivers (35) in the location served by the system are coupled to the transmission lines (30), (31) by electromagnetic wave propagation in space in order to communicate directly with each other at a given radio frequency within the frequency range of the system.

  8. Study of left-handed characteristics of parallel microwires based metastructures

    NASA Astrophysics Data System (ADS)

    Olariu, C. S.; Ababei, G.; Lupu, N.; Chiriac, H.

    2016-04-01

    The aim of this work is to present a complex experimental and theoretical study of the ferromagnetic resonance frequencies and plasma behavior for CoFe-based, Co-based, Fe-based and FINEMETTM glass covered amorphous microwires (GCAWs), arranged in parallel configurations as free-standing systems, as well as combinations thereof, in order to obtain metastructures with tailored and enlarged left-handed frequency domain. The negative magnetic properties interval of the metastructures is expanded by alternating different types of GCAWs with close natural ferromagnetic resonance (NFMR) and natural antiferromagnetic resonance (NFMAR) domains, respectively.

  9. Increased cortical representation of the fingers of the left hand in string players.

    PubMed

    Elbert, T; Pantev, C; Wienbruch, C; Rockstroh, B; Taub, E

    1995-10-13

    Magnetic source imaging revealed that the cortical representation of the digits of the left hand of string players was larger than that in controls. The effect was smallest for the left thumb, and no such differences were observed for the representations of the right hand digits. The amount of cortical reorganization in the representation of the fingering digits was correlated with the age at which the person had begun to play. These results suggest that the representation of different parts of the body in the primary somatosensory cortex of humans depends on use and changes to conform to the current needs and experiences of the individual.

  10. S-Wave Dispersion Relations: Exact Left Hand E-Plane Discontinuity from the Born Series

    NASA Technical Reports Server (NTRS)

    Bessis, D.; Temkin, A.

    1999-01-01

    We show, for a superposition of Yukawa potentials, that the left hand cut discontinuity in the complex E plane of the (S-wave) scattering amplitude is given exactly, in an interval depending on n, by the discontinuity of the Born series stopped at order n. This also establishes an inverse and unexpected correspondence of the Born series at positive high energies and negative low energies. We can thus construct a viable dispersion relation (DR) for the partial (S-) wave amplitude. The high numerical precision achievable by the DR is demonstrated for the exponential potential at zero scattering energy. We also briefly discuss the extension of our results to Field Theory.

  11. Portion of left hand SRB aft segment containing ET attach ring for 51-L

    NASA Technical Reports Server (NTRS)

    1986-01-01

    These two photographs show a portion of the left hand solid rocket booster (SRB) aft segment which contains the external tank (ET) attach ring for the 51-L mission resting on the ocean bottom in 210 feet of water approximately 23 miles east of the Kennedy Space Center (KSC). The photographs were take by the Deep Drone, a remotely controlled, unmanned U.S. Navy submersible. Photo 1 shows small fish below and to the left of the booster segment (10145); Photo two shows the opposite end of the segment. Visible from left are the clevis portion of the field joint and the external tank attach ring (10146).

  12. Pure associative tactile agnosia for the left hand: clinical and anatomo-functional correlations.

    PubMed

    Veronelli, Laura; Ginex, Valeria; Dinacci, Daria; Cappa, Stefano F; Corbo, Massimo

    2014-09-01

    Associative tactile agnosia (TA) is defined as the inability to associate information about object sensory properties derived through tactile modality with previously acquired knowledge about object identity. The impairment is often described after a lesion involving the parietal cortex (Caselli, 1997; Platz, 1996). We report the case of SA, a right-handed 61-year-old man affected by first ever right hemispheric hemorrhagic stroke. The neurological examination was normal, excluding major somaesthetic and motor impairment; a brain magnetic resonance imaging (MRI) confirmed the presence of a right subacute hemorrhagic lesion limited to the post-central and supra-marginal gyri. A comprehensive neuropsychological evaluation detected a selective inability to name objects when handled with the left hand in the absence of other cognitive deficits. A series of experiments were conducted in order to assess each stage of tactile recognition processing using the same stimulus sets: materials, 3D geometrical shapes, real objects and letters. SA and seven matched controls underwent the same experimental tasks during four sessions in consecutive days. Tactile discrimination, recognition, pantomime, drawing after haptic exploration out of vision and tactile-visual matching abilities were assessed. In addition, we looked for the presence of a supra-modal impairment of spatial perception and of specific difficulties in programming exploratory movements during recognition. Tactile discrimination was intact for all the stimuli tested. In contrast, SA was able neither to recognize nor to pantomime real objects manipulated with the left hand out of vision, while he identified them with the right hand without hesitations. Tactile-visual matching was intact. Furthermore, SA was able to grossly reproduce the global shape in drawings but failed to extract details of objects after left-hand manipulation, and he could not identify objects after looking at his own drawings. This case

  13. Electromagnetic-field quantization and spontaneous decay in left-handed media

    SciTech Connect

    Dung, Ho Trung; Buhmann, Stefan Yoshi; Knoell, Ludwig; Welsch, Dirk-Gunnar; Scheel, Stefan; Kaestel, Juergen

    2003-10-01

    We present a quantization scheme for the electromagnetic field interacting with atomic systems in the presence of dispersing and absorbing magnetodielectric media, including left-handed material having negative real part of the refractive index. The theory is applied to the spontaneous decay of a two-level atom at the center of a spherical free-space cavity surrounded by magnetodielectric matter of overlapping band-gap zones. Results for both big and small cavities are presented, and the problem of local-field corrections within the real-cavity model is addressed.

  14. Very simple metallic subwavelength cell for constructing left-handed metamaterial

    NASA Astrophysics Data System (ADS)

    Wang, Zhiyu; Wang, Dongxing; Jiang, Tao; Peng, Liang; Huangfu, Jiangtao; Ran, Lixin

    2009-06-01

    In this letter, a very simple metallic subwavelength cell is designed for constructing left-handed metamaterial. The conductive current mode inside the metallic resonator of this cell imitates one reported displacement current mode inside a dielectric subwavelength resonator. We show by simulation and experiments that an artificial metamaterial composed of cells with such kind of current mode can behave simultaneously negative permittivity and permeability. The metallic cell with double negative property obtained in this letter is suitable for the applications in the high frequency band, such as in millimeter or even terahertz bands.

  15. Surface modes at the interface with left-handed electromagnetic media

    NASA Astrophysics Data System (ADS)

    Darmanyan, Sergei; Neviére, M.; Zakhidov, Anvar

    2003-03-01

    Left handed electromagnetic meta-materials (LHM) have attracted an explosion of interest, after first encouraging observations [2-4], due to tremendous perspectives for applications, such as new lenses and other microwave and optical devices. The experiments of San Diego group have proved experimentally that negative refraction can be achieved by split-ring resonator (SRR) arrays embedded into metallic meshes. In this presentation we address the problem of surface waves at LHM: surface p- and s-polarized stationary waves propagating along the interface between left-handed electromagnetic meta-material (LHM) with three types of conventional materials: metals, dielectrics, and magnetic media with negative m(w)<0 ) are studied. The constraints for the existence of surface modes in each case are identified and analyzed. It is shown that the frequency domains of existence, for p- and s- modes are quite different for different types of interfaces. The Poyting vector and the density of energy associated with surface mode at each type of interface are calculated. Depending on the system parameters either p- or s- surface mode has the time-averaged Poyting vector directed opposite to phase velocity of the interface mode.

  16. The respiratory syncytial virus nucleoprotein-RNA complex forms a left-handed helical nucleocapsid.

    PubMed

    Bakker, Saskia E; Duquerroy, Stéphane; Galloux, Marie; Loney, Colin; Conner, Edward; Eléouët, Jean-François; Rey, Félix A; Bhella, David

    2013-08-01

    Respiratory syncytial virus (RSV) is an important human pathogen. Its nucleocapsid (NC), which comprises the negative sense RNA viral genome coated by the viral nucleoprotein N, is a critical assembly that serves as template for both mRNA synthesis and genome replication. We have previously described the X-ray structure of an NC-like structure: a decameric ring formed of N-RNA that mimics one turn of the helical NC. In the absence of experimental data we had hypothesized that the NC helix would be right-handed, as the N-N contacts in the ring appeared to more easily adapt to that conformation. We now unambiguously show that the RSV NC is a left-handed helix. We further show that the contacts in the ring can be distorted to maintain key N-N-protein interactions in a left-handed helix, and discuss the implications of the resulting atomic model of the helical NC for viral replication and transcription.

  17. Functional MRI evaluation of supplementary motor area language dominance in right- and left-handed subjects.

    PubMed

    Dalacorte, Amauri; Portuguez, Mirna Wetters; Maurer das Neves, Carlos Magno; Anes, Maurício; Dacosta, Jaderson Costa

    2012-01-01

    Functional magnetic resonance imaging (fMRI) is a non-invasive brain imaging technique widely used in the evaluation of the brain function that provides images with high temporal and spatial resolution. Investigation of the supplementary motor area (SMA) function is critical in the pre-surgical evaluation of neurological patients, since marked individual differences and complex overlapping with adjacent cortical areas exist, and it is important to spare the SMA from lesions when adjacent cortical tissue is surgically removed. We used fMRI to assess the activity of SMA in six right-handed and six left-handed healthy volunteers when a task requiring silent repetition of a series of words was given. Brain activation areas in each of the subjects were localized according to the standard Talairach coordinate space, and the individual voxels for each map were compared after 3D sagittal images were created and SMA was delimited. Quantitative analysis of hemispheric and bilateral SMA activation was described as mean ± standard deviation of hot points/total points. The results show that the language task induced bilateral SMA activation. Left SMA activation was significantly higher than right SMA activation in both right-handed and left-handed subjects.

  18. 49 CFR 192.485 - Remedial measures: Transmission lines.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for...

  19. 49 CFR 192.485 - Remedial measures: Transmission lines.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for...

  20. 49 CFR 192.485 - Remedial measures: Transmission lines.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for...

  1. 49 CFR 192.485 - Remedial measures: Transmission lines.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Requirements for Corrosion Control § 192.485 Remedial measures: Transmission lines. (a) General corrosion. Each segment of transmission line with general corrosion and with a remaining wall thickness less than that required for...

  2. Reversed Cherenkov-Transition Radiation by a Charge Crossing a Left-Handed Medium Boundary

    SciTech Connect

    Galyamin, Sergey N.; Tyukhtin, Andrey V.; Kanareykin, Alexey; Schoessow, Paul

    2009-11-06

    We analyze the radiation from a charged particle crossing the boundary between an ordinary medium and a 'left-handed' metamaterial. We obtain exact and approximate expressions for the field components and develop algorithms for their computation. The spatial radiation in this system can be separated into three distinct components, corresponding to ordinary transition radiation having a relatively large magnitude, Cherenkov radiation, and reversed Cherenkov-transition radiation (RCTR). The last one is explained by reflection and refraction of reversed Cherenkov radiation at the interface. Conditions for generating of RCTR are obtained. We note properties of this radiation that have potential applications in the detection of charged particles and accelerator beams and for the characterization of metamaterial macroscopic parameters (epsilon, mu).

  3. Exact solution to plane-wave scattering by an ideal "left-handed" wedge.

    PubMed

    Monzon, Cesar; Forester, Donald W; Smith, Douglas; Loschialpo, Peter

    2006-02-01

    An exact analytical solution to the problem of plane-wave diffraction by a penetrable left-handed medium (LHM) epsilon = micro = -1 wedge of arbitrary angle (subject to valid physical constraints) is presented. Standard analysis involving discontinuous angular eigenfunctions and even/odd symmetry decomposition resulted in a discrete spectrum leading to a series solution resembling the traditional perfect electric conductor wedge solution but exhibiting the expected negative refraction phenomenology. Numerical results are presented, some of which seemed paradoxical but are explainable by classical means. A new type of illusory edge radiation is observed and explained. Also, a novel edge-launched interface standing wave is observed on the directly illuminated side. The exact analytical solution is verified by comparison with finite-difference time-domain simulation on causal LHM materials.

  4. Left-handed polyproline II helix formation is (very) locally driven.

    PubMed

    Creamer, T P

    1998-11-01

    The left-handed polyproline II helix (PPII) is believed to be the preferred conformation for proline-rich regions of sequence in proteins. Such regions have been postulated to be protein-protein interaction domains. The formation of this structure is studied here using simple Monte Carlo computer simulations employing the hard sphere potential. It is found that polyproline sequences adopt only the PPII structure in the simulations. Non-proline, non-glycine residues inserted as guests into polyproline host peptides are conformationally restricted by the following proline residues and tend to be part of the PPII helix. It is found through insertion of two alanine residues into polyproline that the PPII structure is not propagated through more than one non-proline residue. This finding calls into question the hypothesis that proline-rich regions will preferentially adopt this structure since many such sequences are comprised of less than 50% proline residues.

  5. Kuznetsov-Ma waves train generation in a left-handed material

    NASA Astrophysics Data System (ADS)

    Atangana, Jacques; Giscard Onana Essama, Bedel; Biya-Motto, Frederick; Mokhtari, Bouchra; Cherkaoui Eddeqaqi, Noureddine; Crépin Kofane, Timoléon

    2015-03-01

    We analyze the behavior of an electromagnetic wave which propagates in a left-handed material. Second-order dispersion and cubic-quintic nonlinearities are considered. This behavior of an electromagnetic wave is modeled by a nonlinear Schrödinger equation which is solved by collective coordinates theory in order to characterize the light pulse intensity profile. More so, a specific frequency range has been outlined where electromagnetic wave behavior will be investigated. The perfect combination of second-order dispersion and cubic nonlinearity leads to a robust soliton. When the quintic nonlinearity comes into play, it provokes strong and long internal perturbations which lead to Benjamin-Feir instability. This phenomenon, also called modulational instability, induces appearance of a Kuznetsov-Ma waves train. We numerically verify the validity of Kuznetsov-Ma theory by presenting physical conditions which lead to Kuznetsov-Ma waves train generation. Thereafter, some properties of such waves train are also verified.

  6. A phase conjugate mirror inspired approach for building cloaking structures with left-handed materials

    NASA Astrophysics Data System (ADS)

    Zheng, Guoan; Heng, Xin; Yang, Changhuei

    2009-03-01

    In this paper, we propose and examine a new cloaking method, which was inspired by the close correspondence between a phase conjugate mirror and the interface between a pair of matched right-handed material (RHM) and left-handed material (LHM) media. Using this method, we show that a symmetric conducting shell embedded in the interface junction of an isotropic RHM layer and an isotropic negative index or LHM layer can serve as a limited cloaking structure. The proposed structure presents an anomalously small scattering cross-section to an incident propagating electromagnetic (EM) field. The interior of the shell can be used to shield small objects from interrogation. We report the results of 2D finite-element-method (FEM) simulations that were performed to verify the principle, and discuss the limitations of the proposed structure.

  7. Do Right- and Left-Handed Monkeys Differ on Cognitive Measures?

    NASA Technical Reports Server (NTRS)

    Hopkins, William D.; Washburn, David A.

    1994-01-01

    Twelve left- and 14 right-handed monkeys were compared on 6 measures of cognitive performance (2 maze-solving tasks, matching-to-sample, delayed matching-to-sample, delayed response using spatial cues, and delayed response using form cues). The dependent variable was trials-to-training criterion for each of the 6 tasks. Significant differences were found between left- and right-handed monkeys on the 2 versions of the delayed response task. Right-handed monkeys reached criterion significantly faster on the form cue version of the task, whereas left-handed monkeys reached criterion significantly faster on delayed response for spatial position (p less than .05). The results suggest that sensitive hand preference measures of laterality can reveal differences in cognitive performance, which in turn may reflect underlying laterality in functional organization of the nervous system.

  8. Surface integral equation formulation for the analysis of left-handed metamaterials.

    PubMed

    Rivero, J; Taboada, J M; Landesa, L; Obelleiro, F; García-Tuñón, I

    2010-07-19

    A surface integral equation (SIE) formulation is applied to the analysis of electromagnetic problems involving three-dimensional (3D) piecewise homogenized left-handed metamaterials (LHM). The resulting integral equations are discretized by the well-known method of moments (MoM) and solved via an iterative process. The unknowns are defined only on the interfaces between different media, avoiding the discretization of volumes and surrounding space, which entails a drastic reduction in the number of unknowns arising in the numerical discretization of the equations. Besides, the SIE-MoM formulation inherently includes the radiation condition at infinity, so it is not necessary to artificially include termination absorbing boundary conditions. Some 3D numerical examples are presented to confirm the validity and versatility of this approach on dealing with LHM, also providing some intuitive verifications of the singular properties of these amazing materials. PMID:20720970

  9. Left-Handed Effect of Composite Rectangular SRRs and Its Application in Patch Antennae

    NASA Astrophysics Data System (ADS)

    Huang, Ming; Zhou, Yue-Qun; Shen, Ting-Gen

    2010-01-01

    We concentrate on describing the important influence and physical law of the split resonant ring (SRR) based left-handed materials on patch antennae. The finite-difference time-domain method, together with the finite element method is used to study the characteristics of patch antennae based on composite rectangular SRRs. A novel composite rectangular SRR system is formed by assembling the conventional patch antennae and SRRs, it is found that electromagnetic wave resonance occurs near f = 3.15 GHz, the equivalent permittivity and permeability are both negative, and the electromagnetic wave's tunnel effect and evanescent waves' enhancing effect are formed, which can improve the localization extent of electromagnetic wave's energy apparently. Such effects can improve the antenna's radiation gain and its matching condition. The phenomenon indicates that such composite rectangular patch antennae are promising in wireless communications such as mobile phones, satellite communication and aviation.

  10. Surface-wave mechanism of subwavelength imaging by a flat left-handed superlens

    SciTech Connect

    Zharov, A. A.; Zharova, N. A.; Noskov, R. E.

    2009-11-15

    We develop a theory describing the dynamics and interaction of electromagnetic surface waves (ESWs) resonantly excited by an external source in a slab of left-handed material (LHM) with identical negative (equal to -1) values of dielectric permittivity and magnetic permeability that makes up a so-called perfect lens, or a superlens. We show that subwavelength imaging by a superlens is associated with the degeneracy of the spectrum of eigen electromagnetic surface modes at the interfaces of the metamaterial slab, whereas the dynamic response of the superlens is completely determined by the dynamics of these modes and the dispersion properties of the metamaterial. We obtain conditions that enable one to find out when a superlens produces subwavelength images of an external source. We consider the cases of a stationary and a pulse source, as well as of a source that moves with constant velocity or oscillates in space.

  11. Robust wide zero-average-index gap in photonic heterostructures that incorporate left-handed materials

    NASA Astrophysics Data System (ADS)

    EL-Naggar, Sahar A.

    2012-10-01

    In this article, we theoretically study electromagnetic waves that propagate in a one-dimensional photonic heterostructure that contains left-handed materials. We suggest a type of heterostructure that is composed of two photonic crystals (PCs) that consist of different materials, rather than the previously studied heterostructures that are based on changing the thicknesses of alternating layers, to target zero-average-index gap enlargement. Numerical calculations of the transmittance show that the suggested structure possesses an ultra-wide zero-average-index gap that is robust for both transverse electric and magnetic polarizations. The demonstrated wide gap is independent of the incidence angle. The proposed structure works as a perfect stop-band filter, which completely blocks both polarizations, and may have many other potential applications.

  12. Localization of surface modes along a periodic/quasiperiodic structure containing a left-handed material

    NASA Astrophysics Data System (ADS)

    Toledo-Solano, M.; Palomino-Ovando, M. A.; Lozada-Morales, R.

    2015-12-01

    We have investigated the optical properties of a one-dimensional (1-D) photonic periodic/quasiperiodic structure, designed as photonic crystal (PC)-Fibonacci (FN)-photonic crystal (PC) sections. The structure is composed of alternating layers of a right-handed material (RHM) and a left-handed material (LHM). The RHM dielectric function is frequency independent and the LHM (metamaterial) dielectric function and magnetic susceptibility are described according to the Drude model. Using attenuated total reflectivity geometry, we explore the coupling of light with the plasmons on the surface of the metamaterial layers of the hybrid structure. The excitation of surface modes in different frequency regions are investigated. We observed bands of surface modes with a significant selective spatial localization at which the intensity of the electric field is confined almost totally within one of the PC sections or within the FN one.

  13. New Electromagnetic Absorbers Composed of Left-handed and Right-handed Materials

    NASA Astrophysics Data System (ADS)

    Fang, Weihai; Xu, Shanjia

    2008-08-01

    New double-layered electromagnetic absorbers are presented in this paper. The new absorbers composed of one lossy left-handed material absorbing layer and one impedance matching layer consisted of lossless right-handed material. It is indicated that the reflection loss of below -20dB can be obtained in the frequency range 7GHz 13GHz. Power attenuation achieving -50dB of narrow frequency band electromagnetic absorbers can also be obtained by modulate permittivity of right-handed material. Furthermore, the thickness of the whole absorbing structure is only 2mm, which is particularly helpful in some practical applications. The presented results are of reference significance for accurate design of the new electromagnetic absorbers and of practical prospects for stealth technology.

  14. Reduced dream-recall frequency in left-handed adolescents: a replication.

    PubMed

    Schredl, Michael; Beaton, Alan A; Henley-Einion, Josie; Blagrove, Mark

    2014-01-01

    The ability to recall a dream upon waking up in the morning has been linked to a broad variety of factors such as personality, creativity, sleep behaviour and cognitive function. There have been conflicting findings as to whether dream recall is related more to the right or to the left hemisphere, and conflicting findings regarding the relationship of dream-recall frequency to handedness. We have found previously that right- and mixed-handers report having more dreams than left-handers, a finding more pronounced among adolescents than adults. In the present sample of 3535 participants aged from 6 to 18 years, right-handedness and mixed/inconsistent handedness were associated with higher dream-recall frequency compared to that of left-handed persons, again especially in adolescents compared with children. Further research is required to uncover the reason for the lower frequency of dream recall by left-handers.

  15. Conformal hyperthermia of superficial tumor with left-handed metamaterial lens applicator.

    PubMed

    Tao, Yonghui; Wang, Gang

    2012-12-01

    With proper source spacing, low loss left-handed metamaterial (LHM) lens should be useful for hyperthermia treatment of large area tumors. With a flat LHM lens applicator, conformal hyperthermia can be performed by joint heating of multiple microwave sources (antennas). In the hyperthermia, we restrict distance of two neighboring sources within a critical source interval, arrange the sources in a specific array of general shape in accord with the tumor, and adjust the source-to-lens distance to acquire desired inclination of the heating zone for better fit to tumor region. It is shown that inclination can also be adjusted by the phases of microwave sources. A maneuverable LHM-based hyperthermia scheme is thus proposed to generate a relatively large and even tilted heating pattern in tissue.

  16. Heart rate variability differs between right- and left-handed individuals.

    PubMed

    Yüksel, Ramazan; Arslan, Muzeyyen; Dane, Senol

    2014-06-01

    Previous studies reported reduced longevity in left-handers with the suggestion that it may be associated with different heart diseases. Therefore, differences in heart rate variability (HRV), an index of autonomic cardiac activity, were examined for right- and left-handed individuals. 120 healthy young university students (75 women, 45 men; M age = 20.4 yr., SD = 1.5) volunteered. Handedness was assessed with the Edinburgh Handedness Inventory and HRV was measured via electrocardiography. The results suggest that the left-handers' HRV was significantly different from that of right-handers on several parameters. The atypical cerebral organization of left-handers may be related to an imbalanced autonomic system that results in higher frequencies of heart irregularities.

  17. Achieving all-dielectric left-handed metamaterials via single-sized dielectric resonators

    NASA Astrophysics Data System (ADS)

    Wang, Jun; Xu, Zhuo; Du, Bai; Xia, Song; Wang, Jiafu; Ma, Hua; Qu, Shaobo

    2012-02-01

    We demonstrate that using single-sized dielectric resonators, all-dielectric left-handed metamaterial (LHM) can be achieved in the C-band microwave regime. The single-sized rectangular resonator, operating under higher-order resonant modes, possesses electric and magnetic responses simultaneously, leading to the double-negative resonance behavior. We find that the electric/magnetic resonance can be enhanced by elongating the size of the rectangular resonators along the electric field direction. It is shown that polarization currents in dielectric resonators are the same as conduction currents in cut-wire pairs. Experiments were carried out to verify the designed all-dielectric LHM. The proposed method provides a convenient route to all-dielectric LHMs.

  18. A cross-cultural comparison of pressures to switch left-hand writing: Brazil versus Canada.

    PubMed

    Porac, Clare; Martin, William Lee Berdel

    2007-05-01

    Attempts to switch left-hand preferences towards the right side are socialisation practices found in many countries (Perelle & Ehrman, 1994). Although researchers acknowledge that pressures against left-hand use contribute to the cross-cultural fluctuations in the prevalence of left- versus right-hand preference, there has been little systematic cross-cultural study of how these pressures are applied, and who are the major agents applying the pressures to change. Our study explored specific rightward conversion practices and the results of these practices among individuals from two countries. One sample of participants was from a culture categorised as formal, Brazil, and the second sample was from Canada, a nonformal culture (Hofstede, 2001). Researchers have argued that prevalence rates of right-handedness should be higher in cultures that value conformity, called formal cultures, and lower among members of nonformal cultures where conformity pressures are lax (Medland, Perelle, De Monte, & Ehrman, 2004). The socialisation practices used to foster a change from the left to the right side are also predicted to differ in frequency and in kind in formal versus nonformal cultural settings. These cultural differences are assumed to result in differences in success rates of the conversion attempts, with formal cultures producing higher numbers of successfully converted right-handers. Our findings indicate that the formal versus nonformal cultural explanation for cross-cultural fluctuations in the prevalence of hand preference types does not account for the characteristics of the rightward conversion experiences reported by participants in the two groups. We propose that hypotheses concerning the effects of cultural differences on hand preference formation be expanded to include possible biological or genetic variance between groups.

  19. Interactions of Drosophila DNA topoisomerase II with left-handed Z-DNA in supercoiled minicircles.

    PubMed Central

    Glikin, G C; Jovin, T M; Arndt-Jovin, D J

    1991-01-01

    The native form of Drosophila melanogaster DNA topoisomerase II was purified from Schneider's S3 tissue culture cells and studied with two supercoiled minicircle preparations, mini and mini-CG, 354 bp and 370 bp in length, respectively. Mini-CG contains a d(CG)7 insert which assumes a left-handed Z-DNA conformation in negative supercoiled topoisomers with a negative linking number difference - delta Lk greater than or equal to 2. The interactions of topoisomerase II with topoisomer families of mini and mini-CG were studied by band-shift gel electrophoresis in which the individual topoisomers and their discrete or aggregated protein complexes were resolved. A monoclonal anti-Z-DNA IgG antibody (23B6) bound and aggregated only mini-CG, thereby confirming the presence of Z-DNA. Topoisomerase II bound and relaxed mini-CG more readily than mini. In both cases, there was a preference for more highly negatively supercoiled topoisomers. The topoisomerase II inhibitor VM-26 induced the formation of stable covalent DNA-protein intermediates. In addition, the non-hydrolyzable GTP analogue GTP gamma S inhibited the binding and relaxation activities. Experiments to detect topoisomerase cleavage sites failed to elicit specific loci on either minicircle preparation. We conclude that Drosophila topoisomerase II is able to bind and process small minicircles with lengths as short as 360 bp and negative superhelix densities, - sigma, which can exceed 0.1. Furthermore, the enzyme has a preferential affinity for topoisomers containing Z-DNA segments and relaxes these molecules, presumably by cleavage external to the inserts. Thus, a potentially functional relationship between topoisomerase II, an enzyme regulating the topological state of DNA-chromatin in vivo, and left-handed Z-DNA, a conformation stabilized by negative supercoiling, has been established. Images PMID:1662808

  20. A Phase-Conjugate-Mirror Inspired Approach for Building Cloaking Structures with Left-handed Materials

    PubMed Central

    Zheng, Guoan; Heng, Xin; Yang, Changhuei

    2009-01-01

    A phase conjugate mirror (PCM) has a remarkable property of cancellation the back-scattering wave of the lossless scatterers. The similarity of a phase conjugate mirror to the interface of a matched RHM (right-handed material) and a LHM (left-handed material) prompts us to explore the potentials of using the RHM-LHM structure to achieve the anti-scattering property of the PCM. In this paper, we present two such structures. The first one is a RHM-LHM cloaking structure with a lossless arbitrary-shape scatterer imbedded in the RHM and its left-handed duplicate imbedded in the matched LHM. It is shown that such a structure is transparent to the incident electromagnetic (EM) field. As a special case of this structure, we proposed an EM tunnel that allows EM waves to spatially transport to another location in space without significant distortion and reflection. The second one is an RHM-PEC (perfect electric conductor)-LHM cloaking structure, which is composed of a symmetric conducting shell embedded in the interface junction of an RHM and the matched LHM layer. Such a structure presents an anomalously small scattering cross-section to an incident propagating EM field, and the interior of the shell can be used to shield small objects (size comparable to the wavelength) from interrogation. We report the results of 2D finite-element-method (FEM) simulations that were performed to verify our idea, and discuss the unique properties of the proposed structures as well as their limitations. PMID:20126415

  1. A Phase-Conjugate-Mirror Inspired Approach for Building Cloaking Structures with Left-handed Materials.

    PubMed

    Zheng, Guoan; Heng, Xin; Yang, Changhuei

    2009-01-01

    A phase conjugate mirror (PCM) has a remarkable property of cancellation the back-scattering wave of the lossless scatterers. The similarity of a phase conjugate mirror to the interface of a matched RHM (right-handed material) and a LHM (left-handed material) prompts us to explore the potentials of using the RHM-LHM structure to achieve the anti-scattering property of the PCM. In this paper, we present two such structures. The first one is a RHM-LHM cloaking structure with a lossless arbitrary-shape scatterer imbedded in the RHM and its left-handed duplicate imbedded in the matched LHM. It is shown that such a structure is transparent to the incident electromagnetic (EM) field. As a special case of this structure, we proposed an EM tunnel that allows EM waves to spatially transport to another location in space without significant distortion and reflection. The second one is an RHM-PEC (perfect electric conductor)-LHM cloaking structure, which is composed of a symmetric conducting shell embedded in the interface junction of an RHM and the matched LHM layer. Such a structure presents an anomalously small scattering cross-section to an incident propagating EM field, and the interior of the shell can be used to shield small objects (size comparable to the wavelength) from interrogation. We report the results of 2D finite-element-method (FEM) simulations that were performed to verify our idea, and discuss the unique properties of the proposed structures as well as their limitations.

  2. Algorithm for predictive control implementation on fiber optic transmission lines

    NASA Astrophysics Data System (ADS)

    Andreev, Vladimir A.; Burdin, Vladimir A.; Voronkov, Andrey A.

    2014-04-01

    This paper presents the algorithm for predictive control implementation on fiber-optic transmission lines. In order to improve the maintenance of fiber optic communication lines, the algorithm prediction uptime optic communication cables have been worked out. It considers the results of scheduled preventive maintenance and database of various works on the track cable line during maintenance.

  3. Citizens, farmers fight huge transmission lines

    SciTech Connect

    Brummer, J.

    1982-02-01

    Opposition to high tension power lines with a 20-story towers is growing as coalitions of farmers and advocates of safe energy respond with legal intervention and sabotage, and sometimes with success. Examples of citizen action are the efforts opposing a 450 kilovolt direct current line connecting the US with Quebec Hydro and another opposing a 500 kilovolt alternating current line from Georgia Power Co.'s nuclear plants to Florida. The opposition derives partly from evidence of health hazards to humans and adverse effects on livestock. High voltage lines are felt to symbolize a utility and regulatory failure to assess the recent decline in power demand. It is stated that administration efforts to outlaw organized resistence will not deter the opposition, which cites instances of ground shock, aborted and stillborn cattle, physical irritants, and other phenomena. The General Assembly to Stop the Powerline (GASP) objects to the guinea pig position forced upon residents by the utilities. 6 references. (DCK)

  4. Performance robustness of a noise-assisted transmission line

    NASA Astrophysics Data System (ADS)

    Ibáñez, S. A.; Fierens, P. I.; Perazzo, R. P. J.; Grosz, D. F.

    2009-11-01

    In this paper we analyze the stochastic-resonant behavior of a chain of forward-coupled bistable overdamped oscillators used as a transmission line with possible applications to neurophysiology, information transmission and storage. We drive the line with a random sequence of non-return-to-zero bits and each oscillator is independently perturbed by noise. The line is analyzed for varying coupling strengths that lead to different regimes, ranging from noise-supported to coupling-supported transmission. We characterize the transmission performance by parameters such as output bit error rate and delivered signal-to-noise ratio, and show them to improve and remain flat for a broad range of noise intensities in all coupling regimes. In particular, we found that this system exhibits an enhanced robustness as compared to a linear transmission channel impaired only by additive noise.

  5. Single transmission line interrogated multiple channel data acquisition system

    DOEpatents

    Fasching, George E.; Keech, Jr., Thomas W.

    1980-01-01

    A single transmission line interrogated multiple channel data acquisition system is provided in which a plurality of remote station/sensor circuits each monitors a specific process variable and each transmits measurement values over a single transmission line to a master interrogating station when addressed by said master interrogating station. Typically, as many as 330 remote stations may be parallel connected to the transmission line which may exceed 7,000 feet. The interrogation rate is typically 330 stations/second. The master interrogating station samples each station according to a shared, charging transmit-receive cycle. All remote station address signals, all data signals from the remote stations/sensors and all power for all of the remote station/sensors are transmitted via a single continuous terminated coaxial cable. A means is provided for periodically and remotely calibrating all remote sensors for zero and span. A provision is available to remotely disconnect any selected sensor station from the main transmission line.

  6. 10. TRANSMISSION LINES BETWEEN DIABLO AND GORGE; CONSTRUCTION DETAIL OF ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    10. TRANSMISSION LINES BETWEEN DIABLO AND GORGE; CONSTRUCTION DETAIL OF TOWER STRUCTURE, 1989. - Skagit Power Development, Gorge High Dam, On Skagit River, 2.9 miles upstream from Newhalem, Newhalem, Whatcom County, WA

  7. Electrical and Biological Effects of Transmission Lines: A Review.

    SciTech Connect

    Lee, Jack M.

    1989-06-01

    This review describes the electrical properties of a-c and d-c transmission lines and the resulting effects on plants, animals, and people. Methods used by BPA to mitigate undesirable effects are also discussed. Although much of the information in this review pertains to high-voltage transmission lines, information on distribution lines and electrical appliances is included. The electrical properties discussed are electric and magnetic fields and corona: first for alternating-current (a-c) lines, then for direct current (d-c).

  8. Right- and left-handed three-helix proteins. II. Similarity and differences in mechanical unfolding of proteins.

    PubMed

    Glyakina, Anna V; Likhachev, Ilya V; Balabaev, Nikolay K; Galzitskaya, Oxana V

    2014-01-01

    Here, we study mechanical properties of eight 3-helix proteins (four right-handed and four left-handed ones), which are similar in size under stretching at a constant speed and at a constant force on the atomic level using molecular dynamics simulations. The analysis of 256 trajectories from molecular dynamics simulations with explicit water showed that the right-handed three-helix domains are more mechanically resistant than the left-handed domains. Such results are observed at different extension velocities studied (192 trajectories obtained at the following conditions: v = 0.1, 0.05, and 0.01 Å ps(-1) , T = 300 K) and under constant stretching force (64 trajectories, F = 800 pN, T = 300 K). We can explain this by the fact, at least in part, that the right-handed domains have a larger number of contacts per residue and the radius of cross section than the left-handed domains.

  9. Gas insulated transmission line having tapered particle trapping ring

    DOEpatents

    Cookson, Alan H.

    1982-01-01

    A gas-insulated transmission line includes an outer sheath, an inner conductor, insulating supports and an insulating gas. A particle-trapping ring is secured to each insulating support, and it is comprised of a central portion and two tapered end portions. The ends of the particle trapping ring have a smaller diameter than the central portion of the ring, so as to enable the use of the particle trapping ring in a curved transmission line.

  10. Corrugated outer sheath gas-insulated transmission line

    DOEpatents

    Kemeny, George A.; Cookson, Alan H.

    1981-01-01

    A gas-insulated transmission line includes two transmission line sections each of which are formed of a corrugated outer housing enclosing an inner high-voltage conductor disposed therein, with insulating support means supporting the inner conductor within the outer housing and an insulating gas providing electrical insulation therebetween. The outer housings in each section have smooth end sections at the longitudinal ends thereof which are joined together by joining means which provide for a sealing fixed joint.

  11. High aspect ratio transmission line circuits micromachined in silicon

    NASA Astrophysics Data System (ADS)

    Todd, Shane Truman

    The performance of complimentary metal-oxide-semiconductor (CMOS) monolithic microwave integrated circuits (MMICs) fabricated on silicon has improved dramatically. The scaling down of silicon transistors has increased the maximum frequency of transistors to the point where silicon MMICs have become a viable alternative to compound semiconductor MMICs in certain applications. A fundamental problem still exists in silicon MMICs however in that transmission lines fabricated on silicon can suffer from high loss due to the finite conductivity of the silicon substrate. A novel approach for creating low-loss transmission lines on silicon is presented in this work. Low-loss transmission lines are created on low resistivity silicon by using a micromachining method that combines silicon deep reactive ion etching (DRIE), thermal oxidation, electroplating, and planarization. Two types of high aspect ratio transmission lines are created with this method including high aspect ratio coplanar waveguide (hicoplanar) and semi-rectangular coaxial (semicoaxial). Transmission lines with impedances ranging from 20--80 O have been fabricated with minimum measured loss lower than 1 dB/cm at 67 GHz. Low-loss dielectrics are created for the high aspect ratio transmission lines using the mesa merging method. The mesa merging method works by creating silicon mesa arrays using DRIE and then converting and merging the mesa arrays into a solid oxide dielectric using thermal oxidation. The transmission lines are designed so that the fields penetrate the low-loss oxide dielectric and are isolated from the lossy silicon substrate. The mesa merging method has successfully created large volume oxide with depth up to 65 microm and width up to 240 microm in short oxidation times. Other advantages of the high aspect ratio transmission lines are demonstrated including low-loss over a wide impedance range, high isolation, and high coupling for coupled-line circuits. Transmission line models have been

  12. Five Mass Power Transmission Line of a Ship Computer Modelling

    NASA Astrophysics Data System (ADS)

    Kazakoff, Alexander Borisoff; Marinov, Boycho Ivanov

    2016-03-01

    The work, presented in this paper, appears to be a natural continuation of the work presented and reported before, on the design of power transmission line of a ship, but with different multi-mass model. Some data from the previous investigations are used as a reference data, mainly from the analytical investigations, for the developed in the previ- ous study, frequency and modal analysis of a five mass model of a power transmission line of a ship. In the paper, a profound dynamic analysis of a concrete five mass dynamic model of the power transmission line of a ship is performed using Finite Element Analysis (FEA), based on the previously recommended model, investigated in the previous research and reported before. Thus, the partially validated by frequency analysis five mass model of a power transmission line of a ship is subjected to dynamic analysis. The objective of the work presented in this paper is dynamic modelling of a five mass transmission line of a ship, partial validation of the model and von Mises stress analysis calculation with the help of Finite Element Analysis (FEA) and comparison of the derived results with the analytically calculated values. The partially validated five mass power transmission line of a ship can be used for definition of many dy- namic parameters, particularly amplitude of displacement, velocity and acceleration, respectively in time and frequency domain. The frequency behaviour of the model parameters is investigated in frequency domain and it corresponds to the predicted one.

  13. A Generalized Lossy Transmission-Line Model for Tunable Graphene-Based Transmission Lines with Attenuation Phenomenon

    PubMed Central

    Wu, Yongle; Qu, Meijun; Liu, Yuanan

    2016-01-01

    To investigate the frequency shift phenomenon by inserting graphene, a generalized lossy transmission-line model and the related electrical parameter-extraction theory are proposed in this paper. Three kinds of graphene-based transmission lines with attenuation phenomenon including microstrip line, double-side parallel strip line, and uniplanar coplanar waveguide are analyzed under the common conditions where different chemical potentials are loaded on graphene. The values of attenuation constant and phase constant, and the real and imaginary parts of the characteristic impedance of transmission lines are extracted to analyze in details. When the attenuation constant and the reactance part of the characteristic impedance are approximately equal to zero, this kind of transmission line has low or zero insertion loss. On the contrary, the transmission line is under the radiation mode with obvious insertion loss. The phase constant changes linearly under the transmission mode and can be varied with changing of chemical potentials which attributes to the property of frequency tunability. Furthermore, a bandwidth reconfigurable uniplanar coplanar waveguide power divider is simulated to demonstrate that this theory can be applied to the design of three-port devices. In summary, this work provides a strong potential approach and design theory to help design other kinds of terahertz and mid-infrared reconfigurable devices. PMID:27553759

  14. A Generalized Lossy Transmission-Line Model for Tunable Graphene-Based Transmission Lines with Attenuation Phenomenon.

    PubMed

    Wu, Yongle; Qu, Meijun; Liu, Yuanan

    2016-01-01

    To investigate the frequency shift phenomenon by inserting graphene, a generalized lossy transmission-line model and the related electrical parameter-extraction theory are proposed in this paper. Three kinds of graphene-based transmission lines with attenuation phenomenon including microstrip line, double-side parallel strip line, and uniplanar coplanar waveguide are analyzed under the common conditions where different chemical potentials are loaded on graphene. The values of attenuation constant and phase constant, and the real and imaginary parts of the characteristic impedance of transmission lines are extracted to analyze in details. When the attenuation constant and the reactance part of the characteristic impedance are approximately equal to zero, this kind of transmission line has low or zero insertion loss. On the contrary, the transmission line is under the radiation mode with obvious insertion loss. The phase constant changes linearly under the transmission mode and can be varied with changing of chemical potentials which attributes to the property of frequency tunability. Furthermore, a bandwidth reconfigurable uniplanar coplanar waveguide power divider is simulated to demonstrate that this theory can be applied to the design of three-port devices. In summary, this work provides a strong potential approach and design theory to help design other kinds of terahertz and mid-infrared reconfigurable devices. PMID:27553759

  15. A Generalized Lossy Transmission-Line Model for Tunable Graphene-Based Transmission Lines with Attenuation Phenomenon

    NASA Astrophysics Data System (ADS)

    Wu, Yongle; Qu, Meijun; Liu, Yuanan

    2016-08-01

    To investigate the frequency shift phenomenon by inserting graphene, a generalized lossy transmission-line model and the related electrical parameter-extraction theory are proposed in this paper. Three kinds of graphene-based transmission lines with attenuation phenomenon including microstrip line, double-side parallel strip line, and uniplanar coplanar waveguide are analyzed under the common conditions where different chemical potentials are loaded on graphene. The values of attenuation constant and phase constant, and the real and imaginary parts of the characteristic impedance of transmission lines are extracted to analyze in details. When the attenuation constant and the reactance part of the characteristic impedance are approximately equal to zero, this kind of transmission line has low or zero insertion loss. On the contrary, the transmission line is under the radiation mode with obvious insertion loss. The phase constant changes linearly under the transmission mode and can be varied with changing of chemical potentials which attributes to the property of frequency tunability. Furthermore, a bandwidth reconfigurable uniplanar coplanar waveguide power divider is simulated to demonstrate that this theory can be applied to the design of three-port devices. In summary, this work provides a strong potential approach and design theory to help design other kinds of terahertz and mid-infrared reconfigurable devices.

  16. Light reflection by the cuticle of C. aurigans scarabs: a biological broadband reflector of left handed circularly polarized light

    NASA Astrophysics Data System (ADS)

    Libby, E.; Azofeifa, D. E.; Hernández-Jiménez, M.; Barboza-Aguilar, C.; Solís, A.; García-Aguilar, I.; Arce-Marenco, L.; Hernández, A.; Vargas, W. E.

    2014-08-01

    Measured reflection spectra from elytra of Chrysina aurigans scarabs are reported. They show a broad reflection band for wavelengths from 0.525 to 1.0 μm with a sequence of maxima and minima reflection values superimposed on a mean value of around 40% for the high reflection band. Different mechanisms contributing to the reflection spectra have been considered, with the dominant effect, reflection of left handed circularly polarized light, being produced by a laminated left handed twisted structure whose pitch changes with depth through the procuticle in a more complex way than that characterizing broad band circular polarizers based on cholesteric liquid crystals.

  17. Engineering the electrical characteristics of resonant type metamaterial transmission lines

    NASA Astrophysics Data System (ADS)

    Martin, F.; Bonache, J.; Gil, M.; Sisó, G.

    2008-04-01

    This paper is focused on the control of the electrical characteristics of resonant type metamaterial transmission lines, that is, transmission lines loaded with complementary split ring resonators (CSRRs). The key parameters of metamaterial transmission lines for microwave and millimetre wave circuit design are the characteristic impedance and the phase constant (rather than the effective magnetic permeability or dielectric permittivity). Thanks to the presence of reactive elements loading the host line, metamaterial transmission lines exhibit a major design flexibility that can be useful for circuit design purposes. Specifically, we can tailor the dispersion diagram and the characteristic impedance to some extent. By virtue of this, it is possible the design of microwave and millimetre wave components with superior performance in terms of bandwidth, or the design of multi-band components, both of interest in modern wireless communication systems. Thanks to the small electrical size of the unit cell of such lines, the resulting metamaterial-based components are also very small and fully compatible with planar technology (that is, no lumped elements are used). Different examples are provided to illustrate the possibilities of resonant type metamaterial transmission lines. This includes hybrid couplers, power dividers and phase shifters, among others. The paper includes also the theoretical foundations of the approach.

  18. The molecular structure of the left-handed supra-molecular helix of eukaryotic polyribosomes

    NASA Astrophysics Data System (ADS)

    Myasnikov, Alexander G.; Afonina, Zhanna A.; Ménétret, Jean-François; Shirokov, Vladimir A.; Spirin, Alexander S.; Klaholz, Bruno P.

    2014-11-01

    During protein synthesis, several ribosomes bind to a single messenger RNA (mRNA) forming large macromolecular assemblies called polyribosomes. Here we report the detailed molecular structure of a 100 MDa eukaryotic poly-ribosome complex derived from cryo electron tomography, sub-tomogram averaging and pseudo-atomic modelling by crystal structure fitting. The structure allowed the visualization of the three functional parts of the polysome assembly, the central core region that forms a rather compact left-handed supra-molecular helix, and the more open regions that harbour the initiation and termination sites at either ends. The helical region forms a continuous mRNA channel where the mRNA strand bridges neighbouring exit and entry sites of the ribosomes and prevents mRNA looping between ribosomes. This structure provides unprecedented insights into protein- and RNA-mediated inter-ribosome contacts that involve conserved sites through 40S subunits and long protruding RNA expansion segments, suggesting a role in stabilizing the overall polyribosomal assembly.

  19. The molecular structure of the left-handed supra-molecular helix of eukaryotic polyribosomes.

    PubMed

    Myasnikov, Alexander G; Afonina, Zhanna A; Ménétret, Jean-François; Shirokov, Vladimir A; Spirin, Alexander S; Klaholz, Bruno P

    2014-11-07

    During protein synthesis, several ribosomes bind to a single messenger RNA (mRNA) forming large macromolecular assemblies called polyribosomes. Here we report the detailed molecular structure of a 100 MDa eukaryotic poly-ribosome complex derived from cryo electron tomography, sub-tomogram averaging and pseudo-atomic modelling by crystal structure fitting. The structure allowed the visualization of the three functional parts of the polysome assembly, the central core region that forms a rather compact left-handed supra-molecular helix, and the more open regions that harbour the initiation and termination sites at either ends. The helical region forms a continuous mRNA channel where the mRNA strand bridges neighbouring exit and entry sites of the ribosomes and prevents mRNA looping between ribosomes. This structure provides unprecedented insights into protein- and RNA-mediated inter-ribosome contacts that involve conserved sites through 40S subunits and long protruding RNA expansion segments, suggesting a role in stabilizing the overall polyribosomal assembly.

  20. Illusory movements induced by tendon vibration in right- and left-handed people.

    PubMed

    Tidoni, Emmanuele; Fusco, Gabriele; Leonardis, Daniele; Frisoli, Antonio; Bergamasco, Massimo; Aglioti, Salvatore Maria

    2015-02-01

    Frequency-specific vibratory stimulation of peripheral tendons induces an illusion of limb movement that may be useful for restoring proprioceptive information in people with sensorimotor disability. This potential application may be limited by inter- and intra-subject variability in the susceptibility to such an illusion, which may depend on a variety of factors. To explore the influence of stimulation parameters and participants' handedness on the movement illusion, we vibrated the right and left tendon of the biceps brachii in a group of right- and left-handed people with five stimulation frequencies (from 40 to 120 Hz in step of 20 Hz). We found that all participants reported the expected illusion of elbow extension, especially after 40 and 60 Hz. Left-handers exhibited less variability in reporting the illusion compared to right-handers across the different stimulation frequencies. Moreover, the stimulation of the non-dominant arm elicited a more vivid illusion with faster onset relative to the stimulation of the dominant arm, an effect that was independent from participants' handedness. Overall, our data show that stimulation frequency, handedness and arm dominance influence the tendon vibration movement illusion. The results are discussed in reference to their relevance in linking motor awareness, improving current devices for motor ability recovery after brain or spinal damage and developing prosthetics and virtual embodiment systems.

  1. A survey of left-handed dental students and interns in Saudi Arabia.

    PubMed

    Al-Johany, Sulieman S

    2013-01-01

    The purpose of this study was to survey left-handed (LH) dental students and interns concerning whether they face any problems in their dental education or in their practice of dentistry. The questionnaires were distributed in four dental colleges in different regions in Saudi Arabia. The questionnaire was comprised of sixteen questions to assess the following issues: demographic information, difficulties in dental school or dental practice due to left-handedness, preferred hand in performing different dental procedures, and musculoskeletal complications. The study found that the percentage of LH dental students was around 7 percent (110 out of 1,660). More than half of these participants (n=56) reported that being LH is not a problem in general, while when performing the required dental work, around 51 percent (n=56) agreed to having a problem. The majority (68 percent; n=75) reported that they had a problem with having RH instructors, and 84.5 percent (n=93) responded that their institution is not properly equipped to accommodate LH students. Only 34 percent (n=37) agreed that using facilities of an RH dentist may cause musculoskeletal complications to an LH dentist. The results of this study suggest that dental schools should provide LH students with appropriate equipment and a proper learning environment.

  2. Sequence-dependent stability test of a left-handed β-helix motif.

    PubMed

    Hayre, Natha R; Singh, Rajiv R P; Cox, Daniel L

    2012-03-21

    The left-handed β-helix (LHBH) is an intriguing, rare structural pattern in polypeptides that has been implicated in the formation of amyloid aggregates. We used accurate all-atom replica-exchange molecular dynamics (REMD) simulations to study the relative stability of diverse sequences in the LHBH conformation. Ensemble-average coordinates from REMD served as a scoring criterion to identify sequences and threadings optimally suited to the LHBH, as in a fold recognition paradigm. We examined the repeatability of our REMD simulations, finding that single simulations can be reliable to a quantifiable extent. We find expected behavior for the positive and negative control cases of a native LHBH and intrinsically disordered sequences, respectively. Polyglutamine and a designed hexapeptide repeat show remarkable affinity for the LHBH motif. A structural model for misfolded murine prion protein was also considered, and showed intermediate stability under the given conditions. Our technique is found to be an effective probe of LHBH stability, and promises to be scalable to broader studies of this and potentially other novel or rare motifs. The superstable character of the designed hexapeptide repeat suggests theoretical and experimental follow-ups.

  3. Negative refraction and focusing analysis in a left-handed material slab and realization with a 3D photonic crystal structure

    NASA Astrophysics Data System (ADS)

    Ahmadlou, Majid; Kamarei, Mahmoud; Sheikhi, Mohammad Hossein

    2006-02-01

    The increasing interest in metamaterials and structures with negative refraction index requires a formulation capable of a full analysis of wave propagation in such materials and structures. Since two-dimensional (2D) problems have been largely explored in the literature, the natural step is a three-dimensional (3D) formulation of these structures. In this paper, (3D) formulation and simulation of a left-handed metamaterial slab using the finite-difference time domain (FDTD) method in conjunction with perfectly matched layers (PMLs) is presented, and also a (3D) photonic crystal (PC) based structure is presented as a candidate for replacing the left-handed medium slab to realize the negative index of refraction on natural dielectric substrates. The results of these simulations are compared with each other, and the resulting outputs of the developed model are in good agreement. The results demonstrate numerically the focusing of the field emitted from an omnidirectional line source placed in front of the slab and crystal. Both the source and the focus pattern are away from the slab interfaces at two sides of the slab to have a real, negative perfect image. The dimensions of the simulation domain are set to have both source and image in the resulted plots. The focus pattern shows the ability of a photonic crystal structure in making a true flat lens.

  4. Stand-off transmission lines and method for making same

    DOEpatents

    Tuckerman, D.B.

    1991-05-21

    Standoff transmission lines in an integrated circuit structure are formed by etching away or removing the portion of the dielectric layer separating the microstrip metal lines and the ground plane from the regions that are not under the lines. The microstrip lines can be fabricated by a subtractive process of etching a metal layer, an additive process of direct laser writing fine lines followed by plating up the lines or a subtractive/additive process in which a trench is etched over a nucleation layer and the wire is electrolytically deposited. Microstrip lines supported on freestanding posts of dielectric material surrounded by air gaps are produced. The average dielectric constant between the lines and ground plane is reduced, resulting in higher characteristic impedance, less crosstalk between lines, increased signal propagation velocities, and reduced wafer stress. 16 figures.

  5. Stand-off transmission lines and method for making same

    DOEpatents

    Tuckerman, David B.

    1991-01-01

    Standoff transmission lines in an integrated circuit structure are formed by etching away or removing the portion of the dielectric layer separating the microstrip metal lines and the ground plane from the regions that are not under the lines. The microstrip lines can be fabricated by a subtractive process of etching a metal layer, an additive process of direct laser writing fine lines followed by plating up the lines or a subtractive/additive process in which a trench is etched over a nucleation layer and the wire is electrolytically deposited. Microstrip lines supported on freestanding posts of dielectric material surrounded by air gaps are produced. The average dielectric constant between the lines and ground plane is reduced, resulting in higher characteristic impedance, less crosstalk between lines, increased signal propagation velocities, and reduced wafer stress.

  6. NOVEL SIGNAL PROCESSING WITH NONLINEAR TRANSMISSION LINES

    SciTech Connect

    D. REAGOR; ET AL

    2000-08-01

    Nonlinear dielectrics offer uniquely strong and tunable nonlinearities that make them attractive for current devices (for example, frequency-agile microwave filters) and for future signal-processing technologies. The goal of this project is to understand pulse propagation on nonlinear coplanar waveguide prototype devices. We have performed time-domain and frequency-domain experimental studies of simple waveguide structures and pursued a theoretical understanding of the propagation of signals on these nonlinear waveguides. To realistically assess the potential applications, we used a time-domain measurement and analysis technique developed during this project to perform a broadband electrodynamics characterization in terms of nonlinear, dispersive, and dissipative effects. We completed a comprehensive study of coplanar waveguides made from high-temperature superconducting thin-film YBa{sub 2}Cu{sub 3}O{sub 7{minus}{delta}} electrodes on nonlinear dielectric single-crystal SrTiO{sub 3} substrates. By using parameters determined from small-signal (linear) transmission characteristics of the waveguides, we develop a model equation that successfully predicts and describes large-signal (nonlinear) behavior.

  7. Right- and left-handed three-helix proteins. I. Experimental and simulation analysis of differences in folding and structure.

    PubMed

    Glyakina, Anna V; Pereyaslavets, Leonid B; Galzitskaya, Oxana V

    2013-09-01

    Despite the large number of publications on three-helix protein folding, there is no study devoted to the influence of handedness on the rate of three-helix protein folding. From the experimental studies, we make a conclusion that the left-handed three-helix proteins fold faster than the right-handed ones. What may explain this difference? An important question arising in this paper is whether the modeling of protein folding can catch the difference between the protein folding rates of proteins with similar structures but with different folding mechanisms. To answer this question, the folding of eight three-helix proteins (four right-handed and four left-handed), which are similar in size, was modeled using the Monte Carlo and dynamic programming methods. The studies allowed us to determine the orders of folding of the secondary-structure elements in these domains and amino acid residues which are important for the folding. The obtained data are in good correlation with each other and with the experimental data. Structural analysis of these proteins demonstrated that the left-handed domains have a lesser number of contacts per residue and a smaller radius of cross section than the right-handed domains. This may be one of the explanations of the observed fact. The same tendency is observed for the large dataset consisting of 332 three-helix proteins (238 right- and 94 left-handed). From our analysis, we found that the left-handed three-helix proteins have some less-dense packing that should result in faster folding for some proteins as compared to the case of right-handed proteins.

  8. Transmission line icing prediction based on DWT feature extraction

    NASA Astrophysics Data System (ADS)

    Ma, T. N.; Niu, D. X.; Huang, Y. L.

    2016-08-01

    Transmission line icing prediction is the premise of ensuring the safe operation of the network as well as the very important basis for the prevention of freezing disasters. In order to improve the prediction accuracy of icing, a transmission line icing prediction model based on discrete wavelet transform (DWT) feature extraction was built. In this method, a group of high and low frequency signals were obtained by DWT decomposition, and were fitted and predicted by using partial least squares regression model (PLS) and wavelet least square support vector model (w-LSSVM). Finally, the final result of the icing prediction was obtained by adding the predicted values of the high and low frequency signals. The results showed that the method is effective and feasible in the prediction of transmission line icing.

  9. Quasi-Optical Transmission Line for 94-GHz Radar

    NASA Technical Reports Server (NTRS)

    Perez, Raul M.; Veruttipong, Watt

    2008-01-01

    A quasi-optical transmission line (QOTL) has been developed as a low-loss transmission line for a spaceborne cloudobserving radar instrument that operates at a nominal frequency of 94 GHz. This QOTL could also readily be redesigned for use in terrestrial millimeter-wave radar systems and millimeter-wave imaging systems. In the absence of this or another lowloss transmission line, it would be necessary to use a waveguide transmission line in the original radar application. Unfortunately, transmission losses increase and power-handling capacities of waveguides generally decrease with frequency, such that at 94 GHz, the limitation on transmitting power and the combined transmission and reception losses (greater than 5 dB) in a waveguide transmission line previously considered for the original application would be unacceptable. The QOTL functions as a very-lowloss, three-port circulator. The QOTL includes a shaped input mirror that can be rotated to accept 94-GHz transmitter power from either of two high-power amplifiers. Inside the QOTL, the transmitter power takes the form of a linearly polarized beam radiated from a feed horn. This beam propagates through a system of mirrors, each of which refocuses the beam to minimize diffraction losses. A magnetically biased ferrite disc is placed at one of the foci to utilize the Faraday effect to rotate the polarization of the beam by 45 degrees. The beam is then transmitted via an antenna system. The radar return (scatter from clouds, and/or reflections from other objects) is collected by the same antenna and propagates through the Faraday rotator in the reverse of the direction of propagation of the transmitted beam. In the Faraday rotator, the polarization of the received signal is rotated a further 45 degrees, so that upon emerging from the Faraday rotator, the received beam is polarized at 90 with respect to the transmitted beam. The transmitted and received signals are then separated by a wire-grid polarizer.

  10. Conductor design for the VLHC transmission line magnet

    SciTech Connect

    Foster, G.W.; Kashikhin, V.; McAshan, M.; Mazur, P.O.; Piekarz, H.; Volk, J.T.; Walker, R.

    1999-03-01

    The transmission line magnet [1] is under development for the Very Large Hadron Collider (VLHC) at Fermilab with the expectation that it’s cost will be several times less (per Tesla-meter) than conventional superconducting magnets. It is a dual-aperture warm-iron superferric magnet built around an 80kA superconducting transmission line. The superconductor consists of 8 Rutherford (SSC Outer) cables in an Invar pipe jacket. The conductor design requirements and development program is described. A 100kA conductor test facility based on inductive coupling is described.

  11. Gates to Gregg High Voltage Transmission Line Study. [California

    NASA Technical Reports Server (NTRS)

    Bergis, V.; Maw, K.; Newland, W.; Sinnott, D.; Thornbury, G.; Easterwood, P.; Bonderud, J.

    1982-01-01

    The usefulness of LANDSAT data in the planning of transmission line routes was assessed. LANDSAT digital data and image processing techniques, specifically a multi-date supervised classification aproach, were used to develop a land cover map for an agricultural area near Fresno, California. Twenty-six land cover classes were identified, of which twenty classes were agricultural crops. High classification accuracies (greater than 80%) were attained for several classes, including cotton, grain, and vineyards. The primary products generated were 1:24,000, 1:100,000 and 1:250,000 scale maps of the classification and acreage summaries for all land cover classes within four alternate transmission line routes.

  12. Self-monitoring high voltage transmission line suspension insulator

    DOEpatents

    Stemler, Gary E.; Scott, Donald N.

    1981-01-01

    A high voltage transmission line suspension insulator (18 or 22) which monitors its own dielectric integrity. A dielectric rod (10) has one larger diameter end fitting attachable to a transmission line and another larger diameter end fitting attachable to a support tower. The rod is enclosed in a dielectric tube (14) which is hermetically sealed to the rod's end fittings such that a liquidtight space (20) is formed between the rod and the tube. A pressurized dielectric liquid is placed within that space. A discoloring dye placed within this space is used to detect the loss of the pressurized liquid.

  13. Reconfigurable Wave Velocity Transmission Lines for Phased Arrays

    NASA Technical Reports Server (NTRS)

    Host, Nick; Chen, Chi-Chih; Volakis, John L.; Miranda, Felix

    2013-01-01

    Phased array antennas showcase many advantages over mechanically steered systems. However, they are also more complex, heavy and most importantly costly. This presentation paper presents a concept which overcomes these detrimental attributes by eliminating all of the phase array backend (including phase shifters). Instead, a wave velocity reconfigurable transmission line is used in a series fed array arrangement to allow phase shifting with one small (100mil) mechanical motion. Different configurations of the reconfigurable wave velocity transmission line are discussed and simulated and experimental results are presented.

  14. Investigation of Transmission Line Models for Switching Overvoltages Studies

    NASA Astrophysics Data System (ADS)

    Sadeghkhani, Iman; Ketabi, Abbas; Feuillet, Rene

    2013-06-01

    Overvoltages caused by switching operation of power system equipments might damage some equipment and delay power system restoration. This paper presents a comparison between transmission line (TL) models for overvoltages study and investigates which TL model is most proper for every case study. Both simulation time and accuracy factors of TL models are considered for selecting best TL model. Various cases of switching of transformer, shunt reactor, capacitor bank, and transmission line are investigated and simulation results for a partial of 39-bus New England test system, show that the proposed TL model evaluation increase accuracy and reduce simulation time (accelerate power system restoration) properly.

  15. Effects of electromagnetic fields produced by high voltage transmission lines

    NASA Astrophysics Data System (ADS)

    Young, T.

    1984-06-01

    The potential impacts of higher transmission line voltages on people, animals, and plants were determined. The differences among various studies are reviewed. Although there are some obvious dangers posed by transmission line operation, construction, and maintenance, most of these concerns are addressed by safety measures taken by utility companies. The indirect effects of power transission is reported. Three major categories of field effects are covered: (1) corona effects due to the electric field at the conductor's surface; (2) indirect coupling effects, arising from induced currents in nearby conducting objects; and (3) direct coupling effects, caused by induced currents in organisms.

  16. Role of superconductivity in superconducting transmission line resonator

    NASA Astrophysics Data System (ADS)

    Qin, Xiao-Ke

    2016-06-01

    In order to understand the role of superconductivity in superconducting transmission line resonator, we derive the mode equations using the macroscopic wavefunction of the Cooper pairs. We make an appropriate scaling to obtain the dimensionless form of equations and establish the validity of good conductor approximation under most circumstances. Quantization of superconducting transmission line resonator is realized by the black-box principle. We also briefly discuss that the deviation from good conductor behavior would result in the observable effects, such as the considerable decrease of phase velocity and the soliton.

  17. Study of the cavity-magnon-polariton transmission line shape

    NASA Astrophysics Data System (ADS)

    Harder, Michael; Bai, LiHui; Match, Christophe; Sirker, Jesko; Hu, CanMing

    2016-11-01

    We experimentally and theoretically investigate the microwave transmission line shape of the cavity-magnon-polariton (CMP) created by inserting a low damping magnetic insulator into a high quality 3D microwave cavity. While fixed field measurements are found to have the expected Lorentzian characteristic, at fixed frequencies the field swept line shape is in general asymmetric. Such fixed frequency measurements demonstrate that microwave transmission can be used to access magnetic characteristics of the CMP, such as the field line width Δ H. By developing an effective oscillator model of the microwave transmission we show that these line shape features are general characteristics of harmonic coupling. At the same time, at the classical level the underlying physical mechanism of the CMP is electrodynamic phase correlation and a second model based on this principle also accurately reproduces the experimental line shape features. In order to understand the microscopic origin of the effective coupled oscillator model and to allow for future studies of CMP phenomena to extend into the quantum regime, we develop a third, microscopic description, based on a Green's function formalism. Using this method we calculate the transmission spectra and find good agreement with the experimental results.

  18. Modeling of a Variable Focal Length Flat Lens Using Left Handed Metamaterials

    NASA Technical Reports Server (NTRS)

    Reinert, Jason

    2004-01-01

    Left Handed Metamaterials (LHM) were originally purposed by Victor Veselago in1968. These substances would allow a flat structure to focus electromagnetic (EM) waves because they have a negative index of refraction. A similar structure made from conventional materials, those with a positive index of refraction, would disperse the waves. But until recently, these structures have been purely theoretical because substances with both a negative permittivity and negative permeability, material properties necessary for a negative index of refraction, do not naturally exist, Recent developments have produced a structure composed of an array of thin wires and split ring resonators that shows a negative index of refraction. area smaller than a square wavelength. How small the area is can be determined by how perfectly the lens is polished and how pure the substance is that composes the lens. These lenses must also be curved for focusing to occur. The focal length is determined by the curvature of the lens and the material. On the other hand, a flat structure made from LHM would focus light because of the effect of a negative index of refraction in Snell s law. The focal length could also be varied by simply adjusting the distance of the lens from the source of radiation. This could create many devices that are adjustable to different situations in fields such as biomedical imaging and communication. the software package XFDTD which solves Maxwell s equations in the frequency domain as well as the time domain. The program used Drude models of materials to simulate the effect of negative permittivity and negative permeability. Because of this, a LHM can be simulated as a solid block of material instead of an array of wires and split ring resonators. After a flat lens is formed, I am to examine the focusing effect of the lens and determine if a higher resolution flat lens can be developed. Traditional lenses made from conventional materials cannot focus an EM wave onto an My

  19. Electromagnetic wave propagation in left-handed materials and metallic photonic crystals

    NASA Astrophysics Data System (ADS)

    Pokrovski, Alexandre

    Theoretical study of the light propagation in the materials of a new type, which have simultaneously negative electric permittivity epsilon and magnetic permeability mu in the same frequency range and are known as Left-Handed Materials (LHM), is presented. It is shown that in spite of widespread opinion, the refractive index n of the LHM is not necessarily negative. The first and the second thermodynamic laws for electromagnetic field are shown to give two inequalities that are different in the LHM and in the regular materials (RM). Namely, the product Re[n]Im[n] is positive in the RM and negative in the LHM. The second inequality reads that the group velocity is positive in RM and negative in the LHM. Both conditions are quadratic in n, so that the sign of n can be chosen in either way. Moreover, it is shown that if the negative sign is chosen one should change some general electrodynamics definitions. The most important property of the LHM is negative refraction of light at the interface of the RM and the LHM. Russian scientist Victor Veselago has proposed a unique lens for the three-dimensional (3D) imaging based upon this property. The theory of diffraction in the LHM is presented to show that the image of this lens has a usual wavelength smearing though many recent authors claim that this lens is a perfect one. A new lens based upon the LHM is proposed, which is a modification of the Veselago lens. The new lens should be easier to manufacture, it has multiple foci and can image an object located at any large distance from the lens. The new lens might be useful for the 3D imaging. The first LHM has been recently created by the San Diego group. It is based upon the low-frequency (GHz) mode in metallic photonic crystal (MPC). This mode has been interpreted by this group as a plasmon that creates a negative epsilon at low frequencies. An analytical theory of the low frequency modes in the MPC has been presented. It has been shown that the mode under study is not a

  20. 49 CFR 192.707 - Line markers for mains and transmission lines.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... SAFETY TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance... buried main and transmission line: (1) At each crossing of a public road and railroad; and (2)...

  1. Transmission Lines: An Overview of Electrical Properties and Environmental Effects.

    SciTech Connect

    United States. Bonneville Power Administration. Biological Studies Task Team.

    1982-03-01

    A brief overview is provided of environmental and biological effects of high-voltage power transmission lines. Paragraph length descriptions of electric fields, induced voltage and currents, biological effects, magnetic fields, corona, radio and television interference, and ozone are given. 13 figs.

  2. High voltage gas insulated transmission line with continuous particle trapping

    DOEpatents

    Cookson, Alan H.; Dale, Steinar J.

    1983-01-01

    This invention provides a novel high voltage gas insulated transmission line utilizing insulating supports spaced at intervals with snap-in means for supporting a continuous trapping apparatus and said trapping apparatus having perforations and cutouts to facilitate trapping of contaminating particles and system flexibility.

  3. HIGH FREQUENCY POWER TRANSMISSION LINE FOR CYCLOTRONS AND THE LIKE

    DOEpatents

    Armstrong, W.J.

    1954-04-20

    High-frequency power transmission systems, particularly a stacked capacitance alternating power current transmission line wherein maximum utilization of the effective conductios skin of the line conductors is achieved while enabling a low impedance to be obtained are reported. The transmission line consists of a number of flat metal strips with interleaved dielectric strips. The metal dielectric strips are coiled spirally with the axis of the spiral extending along the length of the strips, and the alternating metal strips at the output end have outwardly extending aligned lugs which are directly strapped together and connected to the respective terminals on the load. At the input end of the transmission line, similarly, the alternate metal strips are directly strapped together and connected to an altereating current source. With the arrangement described each metal strip conducts on both sides, so that the metal strips are designed to have a thickness corresponding to twice the depth of the "skin effect" conducting lamina of each conductor at the source frequency.

  4. 77 FR 35366 - Albany-Eugene Transmission Line Rebuild Project

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-06-13

    ... Administration (BPA), Department of Energy (DOE). ACTION: Notice of Availability of Record of Decision (ROD..., based on the Albany-Eugene Transmission Line Rebuild Project (DOE/EIS-0457, March 2012). BPA has decided... will continue to operate at 115 kV. ADDRESSES: Copies of the ROD and EIS may be obtained by calling...

  5. 34. DETAIL OF SIGNAL TRANSMISSION LINES AND CIRCUIT BREAKERS ON ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    34. DETAIL OF SIGNAL TRANSMISSION LINES AND CIRCUIT BREAKERS ON TOP OF BRIDGE, CATENARY ANCHOR BRIDGE 524, NEAR SOUTHWALK SWITCH TOWER - New York, New Haven & Hartford Railroad, Automatic Signalization System, Long Island Sound shoreline between Stamford & New Haven, Stamford, Fairfield County, CT

  6. Flow Impedance in a Uniform Magnetically-Insulated Transmission Line

    SciTech Connect

    Mendel, C.W.

    1999-03-23

    In two recent publications relativistic electron flow in cylindrical magnetically-insulated transmission lines (MITL) was analyzed and modeled under the assumption of negligible electron pressure. Cylindrical MITLs were used because of their common occurrence, and because they are the simplest case of finite width. The authors show in this report that the models apply equally to MITLs of any cross section.

  7. Integrated micromachined transmission lines and endfire slotline antennas

    NASA Astrophysics Data System (ADS)

    Gearhart, Steven S.; Willke, Theodore L.; Onggosanusi, Eko N.

    1997-09-01

    An entirely new class of micromachined 3D microwave and millimeter-wave integrated circuits and antennas are being developed at the University of Wisconsin-Madison using a subset o the LIGA micromachining process. The deep x-ray lithography and metal plating portions of the LIGA process are used to precisely form tall metal structures on semiconductor and dielectric substrates. This micromachining process allows metal height to be included as a parameter in the design of integrated circuits, which will permit several important advancements in high frequency waveguiding circuits and integrated antennas. With appropriate thick- metal cross-sectional geometry, transmission line losses and dispersion may both be reduced on a given substrate. Vertical-walled metal structures allow increased control over element-to-element coupling for integrated coupled-line filters and couplers and result in very significant reductions in ohmic loss. It will be demonstrated that the first single-level coupled-line 3dB coupler can be fabricated using the LIGA process. In addition, the mechanical properties of the thick metal structures will be utilized in the fabrication of integrated antennas and transmission lines that are unsupported by a dielectric substrate. The elimination of the substrate beneath antennas reduces losses to substrate modes, and the elimination o the substrate beneath transmission line filters is necessary for extremely high Q integrated filters. This paper will present simulated loss results that demonstrate the advantages of thick metal transmission lines, measured results of a coupled-line bandpass filter, and a recently fabricated thick-metal tapered slotline antenna which extends nearly a centimeter off of the edge of a GaAs wafer.

  8. Airplane Ice Detector Based on a Microwave Transmission Line

    NASA Technical Reports Server (NTRS)

    Ngo, Phong; Arndt, G. Dickey; Carl, James R.

    2004-01-01

    An electronic instrument that could detect the potentially dangerous buildup of ice on an airplane wing is undergoing development. The instrument is based on a microwave transmission line configured as a capacitance probe: at selected spots, the transmission-line conductors are partly exposed to allow any ice and/or liquid water present at those spots to act as predominantly capacitive electrical loads on the transmission line. These loads change the input impedance of the transmission line, as measured at a suitable excitation frequency. Thus, it should be possible to infer the presence of ice and/or liquid water from measurements of the input impedance and/or electrical parameters related to the input impedance. The sensory transmission line is of the microstrip type and thus thin enough to be placed on an airplane wing without unduly disturbing airflow in flight. The sensory spots are small areas from which the upper layer of the microstrip has been removed to allow any liquid water or ice on the surface to reach the transmission line. The sensory spots are spaced at nominal open-circuit points, which are at intervals of a half wavelength (in the transmission line, not in air) at the excitation frequency. The excitation frequency used in the experiments has been 1 GHz, for which a half wavelength in the transmission line is .4 in. (.10 cm). The figure depicts a laboratory prototype of the instrument. The impedance-related quantities chosen for use in this version of the instrument are the magnitude and phase of the scattering parameter S11 as manifested in the in-phase (I ) and quadrature (Q) outputs of the phase detector. By careful layout of the transmission line (including the half-wavelength sensor spacing), one can ensure that the amplitude and phase of the input to the phase detector keep shifting in the same direction as ice forms on one or more of the sensor areas. Although only one transmission-line sensor strip is used in the laboratory version, in a

  9. [Giant cell tumor of the 4th metacarpal bone of the left hand. Apropos of a case].

    PubMed

    Kamel, E J; Pinto, J A; Potenza, L; Michelena, A; Perez Signini, F; Fuenmayor, A

    1983-01-01

    He is a 46 year old patient that consults on a tumor that deforms the back of his left hand. The X-ray examination shows a bone osteolytic tumor with complete dis appearance of the 4th metacarpal. Surgical removal of the tumor was practiced with immediate reconstruction of the 4th metacarpal by an oseo-iliac graft. Anatomopathological examination. It is an ovoid tumor 6.5 long and irregular surface.

  10. Automated processes in tennis: do left-handed players benefit from the tactical preferences of their opponents?

    PubMed

    Loffing, Florian; Hagemann, Norbert; Strauss, Bernd

    2010-02-01

    Previous research on laterality in sport suggests an over-representation of left-handers in interactive sports such as tennis and cricket. These findings potentially reflect left-handers' advantage over their right-handed competitors in those sports. Although considered crucial for successful performance, the tactical component of their superiority has yet to be analysed. Two studies were conducted to test for a side bias in tennis players' tactical preferences. In the first study, 108 right- and left-handed players of varying skill watched rallies on a computer screen and had to indicate where they would place the ball in the opposing half. The results showed the tactical preference of players to place more balls on a left-handed opponent's mostly stronger forehand side compared with when faced with a right-hander. In the second study, 54 professional tennis matches involving right- and left-handers were analysed with respect to ball placement frequencies on the opponent's backhand side. Significantly fewer balls were hit to the backhand side of a left-handed opponent, thus replicating the findings of Study 1 in on-court situations. Both studies indicate players' preference to place shots to their right irrespective of their opponent's handedness. Findings support the assumption that left-handers might enjoy a strategic advantage in tennis. PMID:20175013

  11. Transferability of different classical force fields for right and left handed α-helices constructed from enantiomeric amino acids.

    PubMed

    Biswas, Santu; Sarkar, Sujit; Pandey, Prithvi Raj; Roy, Sudip

    2016-02-21

    Amino acids can form d and l enantiomers, of which the l enantiomer is abundant in nature. The naturally occurring l enantiomer has a greater preference for a right handed helical conformation, and the d enantiomer for a left handed helical conformation. The other conformations, that is, left handed helical conformations of the l enantiomers and right handed helical conformations of the d enantiomers, are not common. The energetic differences between left and right handed alpha helical peptide chains constructed from enantiomeric amino acids are investigated using quantum chemical calculations (using the M06/6-311g(d,p) level of theory). Further, the performances of commonly used biomolecular force fields (OPLS/AA, CHARMM27/CMAP and AMBER) to represent the different helical conformations (left and right handed) constructed from enantiomeric (D and L) amino acids are evaluated. 5- and 10-mer chains from d and l enantiomers of alanine, leucine, lysine, and glutamic acid, in right and left handed helical conformations, are considered in the study. Thus, in total, 32 α-helical polypeptides (4 amino acids × 4 conformations of 5-mer and 10-mer) are studied. Conclusions, with regards to the performance of the force fields, are derived keeping the quantum optimized geometry as the benchmark, and on the basis of phi and psi angle calculations, hydrogen bond analysis, and different long range helical order parameters. PMID:26863595

  12. Individual left-hand and right-hand intra-digit representations in human primary somatosensory cortex.

    PubMed

    Schweisfurth, Meike A; Frahm, Jens; Schweizer, Renate

    2015-09-01

    Individual intra-digit somatotopy of all phalanges of the middle and little finger of the right and left hand was studied by functional magnetic resonance imaging in 12 healthy subjects. Phalanges were tactilely stimulated and activation in BA 3b of the human primary somatosensory cortex could be observed for each individual phalanx. Activation peaks were further analysed using the Direction/Order (DiOr) method, which identifies somatotopy, if a significantly high number of subjects exhibit ordered distal-to-proximal phalanx representions along a similar direction. Based on DiOr, ordered and similar-direction-aligned intra-digit maps across subjects were found at the left hand for the little and middle finger and at the right hand for the little finger. In these digits the proximal phalanges were represented more medially along the course of the central sulcus than the distal phalanges. This is contrasted by the intra-digit maps for the middle finger of the right hand, which showed larger inter-subject variations of phalanx alignments without a similar within-digit representation across subjects. As all subjects were right-handed and as the middle finger of the dominant hand probably plays a more individual role in everyday tactile performance than the little finger of the right hand and all left-hand digits, the observed variation might reflect a functional somatotopy based on individual use of that particular digit at the dominant hand.

  13. Left-handed DNA: intercalation of the cyanine thiazole orange and structural changes. A kinetic and thermodynamic approach.

    PubMed

    Biver, Tarita; García, Begoña; Leal, José M; Secco, Fernando; Turriani, Elisa

    2010-10-28

    The conditions under which different structures of left-handed DNA (poly(dG-me(5)dC)·poly(dG-me(5)dC)) can exist are investigated by spectrofluorometric, spectrophotometric, circular dichroism and calorimetric measurements and the kinetics of the transformations are analysed. The effects of temperature, salt and ethanol content on the transitions are also studied. The left-handed structure obtained by addition of either Mg(2+) ions or EtOH corresponds to Z-DNA, whereas the structure obtained using the mixture Mg(2+)/EtOH corresponds to the aggregate Z*-DNA. Upon addition of the fluorescent cyanine Thiazole Orange (TO), the transition Z → B immediately starts, whereas Z*-DNA retains its left-handed configuration in the presence of TO provided that the ratio [dye]/[polymer] ≤ 0.1. The equilibria and kinetics of the TO binding to Z*-DNA are investigated under the above conditions using the T-jump technique. The reaction mechanism consists of two series steps, the first one being characterized by the formation of an external electrostatic complex and the second corresponding to the dye penetration between the base pairs. A comparison with the B-DNA/TO system is drawn.

  14. Transferability of different classical force fields for right and left handed α-helices constructed from enantiomeric amino acids.

    PubMed

    Biswas, Santu; Sarkar, Sujit; Pandey, Prithvi Raj; Roy, Sudip

    2016-02-21

    Amino acids can form d and l enantiomers, of which the l enantiomer is abundant in nature. The naturally occurring l enantiomer has a greater preference for a right handed helical conformation, and the d enantiomer for a left handed helical conformation. The other conformations, that is, left handed helical conformations of the l enantiomers and right handed helical conformations of the d enantiomers, are not common. The energetic differences between left and right handed alpha helical peptide chains constructed from enantiomeric amino acids are investigated using quantum chemical calculations (using the M06/6-311g(d,p) level of theory). Further, the performances of commonly used biomolecular force fields (OPLS/AA, CHARMM27/CMAP and AMBER) to represent the different helical conformations (left and right handed) constructed from enantiomeric (D and L) amino acids are evaluated. 5- and 10-mer chains from d and l enantiomers of alanine, leucine, lysine, and glutamic acid, in right and left handed helical conformations, are considered in the study. Thus, in total, 32 α-helical polypeptides (4 amino acids × 4 conformations of 5-mer and 10-mer) are studied. Conclusions, with regards to the performance of the force fields, are derived keeping the quantum optimized geometry as the benchmark, and on the basis of phi and psi angle calculations, hydrogen bond analysis, and different long range helical order parameters.

  15. On the advantage of being left-handed in volleyball: further evidence of the specificity of skilled visual perception.

    PubMed

    Loffing, Florian; Schorer, Jörg; Hagemann, Norbert; Baker, Joseph

    2012-02-01

    High ball speeds and close distances between competitors require athletes in interactive sports to correctly anticipate an opponent's intentions in order to render appropriate reactions. Although it is considered crucial for successful performance, such skill appears impaired when athletes are confronted with a left-handed opponent, possibly because of athletes' reduced perceptual familiarity with rarely encountered left-handed actions. To test this negative perceptual frequency effect hypothesis, we invited 18 skilled and 18 novice volleyball players to predict shot directions of left- and right-handed attacks in a video-based visual anticipation task. In accordance with our predictions, and with recent reports on laterality differences in visual perception, the outcome of left-handed actions was significantly less accurately predicted than the outcome of right-handed attacks. In addition, this left-right bias was most distinct when predictions had to be based on preimpact (i.e., before hand-ball contact) kinematic cues, and skilled players were generally more affected by the opponents' handedness than were novices. The study's findings corroborate the assumption that skilled visual perception is attuned to more frequently encountered actions.

  16. Cisplatin GG-crosslinks within single-stranded DNA: origin of the preference for left-handed helicity.

    PubMed

    Monnet, Jordan; Kozelka, Jiří

    2012-10-01

    Molecular dynamics (MD) simulations of the single-stranded DNA trinucleotide TG*G*, with the G* guanines crosslinked by the antitumor drug cisplatin, were performed with explicit representation of the water as solvent. The purpose of the simulations was to explain previous NMR observations indicating that in single-stranded cisplatin-DNA adducts, the crosslinked guanines adopt a left-handed helical orientation, whereas in duplexes, the orientation is right-handed. The analysis of the MD trajectory of TG*G* has ascribed a crucial role to hydrogen-bonding (direct or through-water) interactions of the 5'-oriented NH(3) ligand of platinum with acceptor groups at the 5'-side of the crosslink, namely the TpG* phosphate and the terminal 5'-OH group. These interactions bring about some strain into the trinucleotide which is slightly but significantly (1-1.5 kcal.mol(-1)) higher for the right-handed orientation than for the left-handed one. During the unconstrained, 3 ns long MD simulation, left-handed conformations were ~15 times more abundant than the right-handed ones. This sampling difference agrees roughly with the calculated energy difference in strain energy. Overall, these results show that the Pt-GG crosslink within single-stranded DNA is malleable and can access different conformations at a moderate energy cost. This malleability could be of importance in interactions between the platinated DNA and cellular proteins, in which the DNA is locally unwound.

  17. Subunit b-dimer of the Escherichia coli ATP synthase can form left-handed coiled-coils.

    PubMed

    Wise, John G; Vogel, Pia D

    2008-06-01

    One remaining challenge to our understanding of the ATP synthase concerns the dimeric coiled-coil stator subunit b of bacterial synthases. The subunit b-dimer has been implicated in important protein interactions that appear necessary for energy conservation and that may be instrumental in energy conservation during rotary catalysis by the synthase. Understanding the stator structure and its interactions with the rest of the enzyme is crucial to the understanding of the overall catalytic mechanism. Controversy exists on whether subunit b adopts a classic left-handed or a presumed right-handed dimeric coiled-coil and whether or not staggered pairing between nonhomologous residues in the homodimer is required for intersubunit packing. In this study we generated molecular models of the Escherichia coli subunit b-dimer that were based on the well-established heptad-repeat packing exhibited by left-handed, dimeric coiled-coils by employing simulated annealing protocols with structural restraints collected from known structures. In addition, we attempted to create hypothetical right-handed coiled-coil models and left- and right-handed models with staggered packing in the coiled-coil domains. Our analyses suggest that the available structural and biochemical evidence for subunit b can be accommodated by classic left-handed, dimeric coiled-coil quaternary structures.

  18. Automated processes in tennis: do left-handed players benefit from the tactical preferences of their opponents?

    PubMed

    Loffing, Florian; Hagemann, Norbert; Strauss, Bernd

    2010-02-01

    Previous research on laterality in sport suggests an over-representation of left-handers in interactive sports such as tennis and cricket. These findings potentially reflect left-handers' advantage over their right-handed competitors in those sports. Although considered crucial for successful performance, the tactical component of their superiority has yet to be analysed. Two studies were conducted to test for a side bias in tennis players' tactical preferences. In the first study, 108 right- and left-handed players of varying skill watched rallies on a computer screen and had to indicate where they would place the ball in the opposing half. The results showed the tactical preference of players to place more balls on a left-handed opponent's mostly stronger forehand side compared with when faced with a right-hander. In the second study, 54 professional tennis matches involving right- and left-handers were analysed with respect to ball placement frequencies on the opponent's backhand side. Significantly fewer balls were hit to the backhand side of a left-handed opponent, thus replicating the findings of Study 1 in on-court situations. Both studies indicate players' preference to place shots to their right irrespective of their opponent's handedness. Findings support the assumption that left-handers might enjoy a strategic advantage in tennis.

  19. Wireless Sensor Network for Electric Transmission Line Monitoring

    SciTech Connect

    Alphenaar, Bruce

    2009-06-30

    Generally, federal agencies tasked to oversee power grid reliability are dependent on data from grid infrastructure owners and operators in order to obtain a basic level of situational awareness. Since there are many owners and operators involved in the day-to-day functioning of the power grid, the task of accessing, aggregating and analyzing grid information from these sources is not a trivial one. Seemingly basic tasks such as synchronizing data timestamps between many different data providers and sources can be difficult as evidenced during the post-event analysis of the August 2003 blackout. In this project we investigate the efficacy and cost effectiveness of deploying a network of wireless power line monitoring devices as a method of independently monitoring key parts of the power grid as a complement to the data which is currently available to federal agencies from grid system operators. Such a network is modeled on proprietary power line monitoring technologies and networks invented, developed and deployed by Genscape, a Louisville, Kentucky based real-time energy information provider. Genscape measures transmission line power flow using measurements of electromagnetic fields under overhead high voltage transmission power lines in the United States and Europe. Opportunities for optimization of the commercial power line monitoring technology were investigated in this project to enable lower power consumption, lower cost and improvements to measurement methodologies. These optimizations were performed in order to better enable the use of wireless transmission line monitors in large network deployments (perhaps covering several thousand power lines) for federal situational awareness needs. Power consumption and cost reduction were addressed by developing a power line monitor using a low power, low cost wireless telemetry platform known as the ''Mote''. Motes were first developed as smart sensor nodes in wireless mesh networking applications. On such a platform

  20. [Left hand clumsiness due to disturbance of kinesthesia after damage to the dorsal column of the high cervical cord].

    PubMed

    Hashimoto, R; Kanho, M; Fujimoto, K; Tanaka, Y

    1997-04-01

    We described a 48-year-old, right-handed woman who manifested left hand clumsiness after damage to the dorsal column of the high cervical cord due to probable multiple sclerosis. On February 29, 1996, she developed a weakness in the right limbs. Subsequently, she suffered numbness and clumsiness in the left limbs, even though muscle strength of the left limbs was preserved. Seventeen days later, she was referred to our hospital. A T2-weighted MRI after admission demonstrated high signal intensities in the left dorsal column and the right antero-lateral part of the cervical cord at the C1 to C3 vertebral level. Under the diagnosis of probable multiple sclerosis, steroid pulse therapy was applied twice and she gradually regained muscle strength in the right limbs and sensation in the left limbs. One month later, elemental sensations such as pain, touch, temperature, vibration, and position, as well as discriminative sensations such as localization sensation, two-point discrimination, barognosis, pinch-press discrimination, and graphesthesia in the left limbs returned to normal. However, her left hand remained clumsy, especially when she tried to manipulate objects. She also showed a great difficulty in sustaining a constant level of pinching force by the left thumb and index finger, and in localizing her right thumb placed in space with the left hand with her eyes closed. She stated herself that she could not sense at all how her left hand and fingers were moving. Somatosensory evoked potentials recorded from the right scalp showed that the NI was poorly organized and the patency of subsequent peaks was delayed. Transcranial magnetic stimulation revealed that the pyramidal tract from the right motor cortex to the left cervical cord was functionally intact. These observations lead us to conclude as follows: (1) the patient's left hand clumsiness is probably due to the disturbance of kinesthesia, which is crucial to activate temporo-spatial patterns of complex hand and

  1. Transmission capability of asymmetric digital subscriber lines in Taiwan

    NASA Astrophysics Data System (ADS)

    Wei, Shyue-Win; Leu, Shyue-Tzong; Wei, Che-Ho

    1995-04-01

    The transmission capacity of discrete multitone (DMT) modulation system for Taiwan's subscriber loops is evaluated in this study. Based on the characteristics of Taiwan's local loops, the transmission capacity is estimated to be 1.544 Mb/s and 6 Mb/s in Taiwan. Simulation results also show how many percents of users in Taiwan may have 1.544 Mb/s or 6 Mb/s of asymmetric digital subscriber lines (ADSL) services. Self far-end crosstalk (FEXT) and additive white Gaussian noise (AWGN) are considered to be the dominant noise sources in the work.

  2. Low-power digital communication with unterminated transmission lines

    NASA Astrophysics Data System (ADS)

    Cooperman, Michael; Sieber, Richard W.; Moolenbeek, Rob

    1988-06-01

    Conventional telecommunication techniques are optimized to communicate over long distances (greater than 1 mi), subject to high attenuation, high crosstalk, and other deteriorations in transmission. A trend in telecommunication system architectures is to disperse the previously centralized switching centers, thereby providing switching within a few hundred feet of the subscriber. This creates an opportunity for great improvements in cost and performance for short distance communication links. A technique for low-power digital communication over short transmission lines that exploits this possibility is described. The typical power is more than an order of magnitude lower than the power required with conventional circuits. Associated with this technique are a tenfold reduction in the chip area occupied by the transmission line drivers and the elimination of coupling transformers. The power and chip-area reductions result from terminating the line at the transmitter and maintaining an open circuit at the receiver. These advantages make this line-driving technique particularly suitable for single-chip VLSI systems.

  3. A comparison of digital subscriber line transmission systems employing different line codes

    NASA Astrophysics Data System (ADS)

    Brosio, A.; Dejulio, U.; Lazzari, V.; Ravaglia, R.; Tofanelli, A.

    1981-12-01

    The main characteristics and the performance of two systems implemented for two wire digital transmission on subscriber lines are presented. Both systems utilize different time intervals to transit bursts of bits in the two directions with an information bit rate of 80 kbit/s and a line bit rate in the bursts of 256 kbit/s. One system employing WAL2 as the line code, exhibits extreme circuitry simplicity and low power consumption. The other system, which employs CMI as the line code, shows better performance in the presence of line disturbances.

  4. Tunable Transmission-Line Metamaterials Mimicking Electromagnetically Induced Transparency

    NASA Astrophysics Data System (ADS)

    Feng, T. H.; Han, H. P.

    2016-11-01

    Tunable transmission-line (TL) metamaterials mimicking electromagnetically induced transparency (EIT) have been studied. Firstly, two types of tunable TL EIT-like metamaterial, based on the double split-ring resonator (DSRR) and single split-ring resonator (SSRR), were fabricated and their transmission properties carefully compared. The results showed that the transmittance maximum was almost invariable with shift of the transparency window for the tunable DSRR-based TL EIT-like metamaterial, but for the tunable SSRR-based TL EIT-like metamaterial, the transmittance maximum gradually diminished with shift of the transparency window toward the center of the absorption band. Moreover, the reason for these different transmission properties was explored, revealing that the reduction of the transmittance maximum of the transparency window for the tunable SSRR-based TL EIT-like metamaterial is mainly due to energy loss caused by the resistance of the loaded varactor diodes.

  5. Tunable Transmission-Line Metamaterials Mimicking Electromagnetically Induced Transparency

    NASA Astrophysics Data System (ADS)

    Feng, T. H.; Han, H. P.

    2016-08-01

    Tunable transmission-line (TL) metamaterials mimicking electromagnetically induced transparency (EIT) have been studied. Firstly, two types of tunable TL EIT-like metamaterial, based on the double split-ring resonator (DSRR) and single split-ring resonator (SSRR), were fabricated and their transmission properties carefully compared. The results showed that the transmittance maximum was almost invariable with shift of the transparency window for the tunable DSRR-based TL EIT-like metamaterial, but for the tunable SSRR-based TL EIT-like metamaterial, the transmittance maximum gradually diminished with shift of the transparency window toward the center of the absorption band. Moreover, the reason for these different transmission properties was explored, revealing that the reduction of the transmittance maximum of the transparency window for the tunable SSRR-based TL EIT-like metamaterial is mainly due to energy loss caused by the resistance of the loaded varactor diodes.

  6. Comparison of Transmission Line Methods for Surface Acoustic Wave Modeling

    NASA Technical Reports Server (NTRS)

    Wilson, William; Atkinson, Gary

    2009-01-01

    Surface Acoustic Wave (SAW) technology is low cost, rugged, lightweight, extremely low power and can be used to develop passive wireless sensors. For these reasons, NASA is investigating the use of SAW technology for Integrated Vehicle Health Monitoring (IVHM) of aerospace structures. To facilitate rapid prototyping of passive SAW sensors for aerospace applications, SAW models have been developed. This paper reports on the comparison of three methods of modeling SAWs. The three models are the Impulse Response Method (a first order model), and two second order matrix methods; the conventional matrix approach, and a modified matrix approach that is extended to include internal finger reflections. The second order models are based upon matrices that were originally developed for analyzing microwave circuits using transmission line theory. Results from the models are presented with measured data from devices. Keywords: Surface Acoustic Wave, SAW, transmission line models, Impulse Response Method.

  7. Beam coupling impedances of fast transmission-line kickers.

    SciTech Connect

    Kurennoy, S.

    2002-01-01

    Fast transmission-line kickers contain no ferrite and consist of two long metallic parallel plates supported by insulators inside a beam pipe. A beam is deflected by both the electric and magnetic fields of a TEM wave created by a pulse propagating along the strips in the direction opposite to the beam. Computations of the beam coupling impedances for such structures are difficult because of their length. In the paper, the beam coupling impedances of transmission-line kickers are calculated by combining analytical and numerical methods: the wake potentials computed in short models are extended analytically to obtain the wakes for the long kickers, and then the corresponding beam impedances are derived. At very low frequencies the results are compared with simple analytical expressions for the coupling impedances of striplines in beam position monitors.

  8. HTS DC Transmission Line for Megalopolis Grid Development

    NASA Astrophysics Data System (ADS)

    Kopylov, S.; Sytnikov, V.; Bemert, S.; Ivanov, Yu; Krivetskiy, I.; Romashov, M.; Shakaryan, Yu; Keilin, V.; Shikov, A.; Patrikeev, V.; Lobyntsev, V.; Shcherbakov, V.

    2014-05-01

    Using of HTS AC and DC cables in electric power grids allows increasing of the transferred power, losses diminishing, decreasing of exclusion zone areas, the enhancement of the environmental conditions and fire/explosion safety of electric power systems. However, the use of DC superconducting cable lines together with converters brings additional advantages as reduction of losses in cables and suitable lowering of refrigerating plant capacity, as well as the realization of the function of short-circuit currents limitation by means of the appropriate setting of converter equipment. Russian Federal Grid Company and its R&D Center started the construction of the DC HTS power transmission line which includes the cable itself, cryogenic equipment, AC/DC converters, terminals and cable coupling boxes. This line will connect two substations in Saint-Petersburg - 330 kV "Centralnaya" and 220 kV "RP-9". The length of this HTS transmission line will be about 2500 meters. Nowadays are developed all the elements of the line and technologies of the cable manufacturing. Two HTS cable samples, each 30 m length, have been made. This paper describes the results of cables tests.

  9. Reconfigurable Wave Velocity Transmission Lines for Phased Arrays

    NASA Technical Reports Server (NTRS)

    Host, Nicholas Keith; Chen, Chi-Chih; Volakis, John L.

    2012-01-01

    This presentation discussed a novel phased array with an emphasis to simplify the array feed. Specifically, we will demonstrate a simple, low cost feeding approach by mechanically controlling the substrate thickness. The array feed lines are constructed from parallel plate transmission lines whose thickness are adjusted to control their effective dielectric constant (Epsilon_eff). As a result the phase delay/excitation at each array element will be adjusted per desired beam direction. The proposed antenna elements will be overlapping dipoles operating over a 2:1 bandwidth in the Ku-Band spectrum. Preliminary simulation and experimental demonstration of such an array will be presented.

  10. Transmission Line for 258 GHz Gyrotron DNP Spectrometry

    NASA Astrophysics Data System (ADS)

    Bogdashov, Alexandr A.; Belousov, Vladimir I.; Chirkov, Alexey V.; Denisov, Gregory G.; Korchagin, Vyacheslav V.; Kornishin, Sergey Yu.; Tai, Evgeny M.

    2011-06-01

    We describe the design and test results of the transmission line for liquid-state (LS) and solid-state (SS) DNP spectrometers with the second-harmonic 258.6 GHz gyrotron at the Institute of the Biophysical Chemistry Center of Goethe University (Frankfurt). The 13-meter line includes a mode converter, HE11 waveguides, 4 mitre bends, a variable polarizer-attenuator, directional couplers, a water-flow calorimeter and a mechanical switch. A microwave power of about 15 W was obtained in the pure HE11 mode at the spectrometer inputs.

  11. Flow impedance in a uniform magnetically insulated transmission line

    SciTech Connect

    Mendel, C.W. Jr.; Seidel, D.B.

    1999-12-01

    In two recent publications [C. W. Mendel, Jr. and S. E. Rosenthal, Phys. of Plasmas {bold 2}, 1332 (1995), C. W. Mendel, Jr. and S. E. Rosenthal, Phys. of Plasmas {bold 3}, 4207 (1996)] relativistic electron flow in cylindrical magnetically insulated transmission lines was analyzed and modeled under the assumption of negligible electron pressure. The model allows power flow in these lines to be accurately calculated under most conditions. The model was developed for coaxial right circular cylindrical electrodes. It is shown here that the model applies equally well to arbitrary cylindrical systems, i.e., systems consisting of electrodes of arbitrary cross section. {copyright} {ital 1999 American Institute of Physics.}

  12. Flow impedance in a uniform magnetically insulated transmission line

    NASA Astrophysics Data System (ADS)

    Mendel, C. W.; Seidel, D. B.

    1999-12-01

    In two recent publications [C. W. Mendel, Jr. and S. E. Rosenthal, Phys. of Plasmas 2, 1332 (1995), C. W. Mendel, Jr. and S. E. Rosenthal, Phys. of Plasmas 3, 4207 (1996)] relativistic electron flow in cylindrical magnetically insulated transmission lines was analyzed and modeled under the assumption of negligible electron pressure. The model allows power flow in these lines to be accurately calculated under most conditions. The model was developed for coaxial right circular cylindrical electrodes. It is shown here that the model applies equally well to arbitrary cylindrical systems, i.e., systems consisting of electrodes of arbitrary cross section.

  13. Gas insulated transmission line with insulators having field controlling recesses

    DOEpatents

    Cookson, Alan H.; Pederson, Bjorn O.

    1984-01-01

    A gas insulated transmission line having a novel insulator for supporting an inner conductor concentrically within an outer sheath. The insulator has a recess contiguous with the periphery of one of the outer and inner conductors. The recess is disposed to a depth equal to an optimum gap for the dielectric insulating fluid used for the high voltage insulation or alternately disposed to a large depth so as to reduce the field at the critical conductor/insulator interface.

  14. Nonlinear waves propagating in the electrical transmission line

    NASA Astrophysics Data System (ADS)

    Duan, W.-S.

    2004-04-01

    A coupled Zakharov-Kuznetsov (ZK) equation is derived for a nonlinear transmission line in which the nonlinear capacitance C is of a general form C = C0(1 + k1V + k2V2 + ...). For a solitary-wave solution of the ZK equation, there is an instability region which is given numerically in this paper. It is in agreement with the analytical results for special cases.

  15. Mitigation of bird collisions with transmission lines: Final report

    SciTech Connect

    Beaulaurier, D.L.

    1981-09-11

    In this study removal of overhead groundwires was evaluated as a technique for mitigating bird collisions with transmission lines. Groundwires were removed by BPA from a 500 kV double circuit line at Bybee Lake in Portland, Oregon. Earlier studies at these sites had documented small but measurable collision rates (i.e., No. collisions/No. flights) attributed primarily to collisions with groundwires. Observations of bird flights and searches for dead birds in the vicinity of the lines constituted the primary methods of data collection during pre- and post-removal studies. Field work was conducted from October 1980 through March 1981. A total of seven dead birds and eight feather spots were found after groundwire removal. Species found were green-winged teal, pintail, greater scaup, American wigeon, glaucous-winged gull, starling, red-winged blackbird and song sparrow. No collisions with transmission lines were observed. During pre-removal studies at these two sites, a total of 53 dead birds and 22 feather spots were found over two years of study. It was necessary to document flight intensity (No. flights/day) during pre- and post-removal studies, in order to determine if the number of dead birds found changed because of groundwire removal or simply because of changes in flight intensity. 41 refs., 18 figs., 22 tabs.

  16. Dynamic modeling of magnetically insulated transmission line systems

    SciTech Connect

    Mendel, C.W. Jr.; Rosenthal, S.E.

    1996-11-01

    Negative conductors in vacuum transmission lines used in multiterrawatt applications emit electrons freely. These lines are efficient only because the self-magnetic field of the power flow forces the electrons to flow parallel to the electrodes. Excepting numerical simulations, dynamic modeling of systems of these transmission lines has generally either ignored electron flow, or has included only those electrons that cross immediately to the anode at the front of the forward wave. In this paper we describe an analytic model that includes flowing electrons and the effects of these flows on line voltage and on the reduction of magnetic flux. Axial electron currents are modeled using simple, measurable, and calculable parameters. Transverse electron currents are modeled using general patterns found empirically from simulation data. These currents are in turn related by an expanded set of Telegrapher equations. An example of the use of the model is compared to two-dimensional, time-dependent particle-in-cell simulations. {copyright} {ital 1996 American Institute of Physics.}

  17. Left-handed Z' and Z FCNC quark couplings facing new b → sμ + μ - data

    NASA Astrophysics Data System (ADS)

    Buras, Andrzej J.; Girrbach, Jennifer

    2013-12-01

    In view of the recent improved data on B s,d → μ + μ - and B d → K * μ + μ - we revisit two simple New Physics (NP) scenarios analyzed by us last year in which new FCNC currents in b → sμ + μ - transitions are mediated either entirely by a neutral heavy gauge boson Z ' with purely left-handed complex couplings and real couplings to muons and or the SM Z boson with left-handed complex couplings . We demonstrate how the reduced couplings, the couplings in question divided by M Z' or M Z, can be determined by future Δ F = 2 and b → sμ + μ - observables up to sign ambiguities. The latter do not affect the correlations between various observables that can test these NP scenarios. We present the results as functions of and which should be precisely determined in this decade. We calculate the violation of the CMFV relation between and Δ M s,d in these scenarios. We find that the data on B s,d → μ + μ - from CMS and LHCb can be reproduced in both scenarios but in the case of Z, Δ M s and S ψϕ have to be very close to their SM values. As far as B d → K * μ + μ - anomalies are concerned the Z' scenario can significantly soften these anomalies while the Z boson fails badly because of the small vector coupling to muons. We also point out that recent proposals of explaining these anomalies with the help of a real Wilson coefficient implies uniquely an enhancement of Δ M s with respect to its SM value, while a complex allows for both enhancement and suppression of Δ M s and simultaneously novel CP-violating effects. Correlations between b → sμ + μ - and observables in these scenarios are emphasized. We also discuss briefly scenarios in which the Z' boson has right-handed FCNC couplings. In this context we point out a number of correlations between angular observables measured in B d → K * μ + μ - that arise in the absence of new CP-violating phases in scenarios with only left-handed or right-handed couplings or scenarios in which left-handed

  18. Ratio between the amplitude of sensory evoked potentials at the wrist in both hands of left-handed subjects.

    PubMed Central

    Martínez, A C; Conde, M C; Campo, F D; Mingo, P; Ferrer, M T

    1980-01-01

    Maximum sensory conduction velocity, duration and amplitude of the sensory evoked potentials at the wrist on stimulating digits 1, 2, 3 and 5, were determined bilaterally in 21 left-handed subjects with an age range from 6 to 47 years. The amplitude of the sensory evoked potential at the wrist was larger in the right hand. This asymmetry is the reverse of the one previously observed in right-handed infants and adults. It could be physiological and suggests a difference in density of sensory innervation between the two hands. Asymmetry of sensory innervation can be helpful in the study of hand dominance. PMID:7359155

  19. Radiofrequency transmission line for bioluminescent Vibrio sp. irradiation

    NASA Astrophysics Data System (ADS)

    Nassisi, V.; Alifano, P.; Talà, A.; Velardi, L.

    2012-07-01

    We present the study and the analyses of a transmission line for radiofrequency (RF) irradiation of bacteria belonging to Vibrio harveyi-related strain PS1, a bioluminescent bacterium living in symbiosis with many marine organisms. The bioluminescence represents a new biologic indicator which is useful for studying the behaviour of living samples in the presence of RF waves due to the modern communication systems. A suitable transmission line, used as an irradiating cell and tested up to the maximum frequency used by the global system for mobile communications and universal mobile telecommunications system transmissions, was characterized. In this experiment, the RF voltage applied to the transmission line was 1 V. Due to short dimensions of the line and the applied high frequencies, standing waves were produced in addition to progressing waves and the electric field strength varies particularly along the longitudinal direction. The magnetic field map was not strongly linked to the electric one due to the presence of standing waves and of the outgoing irradiation. RF fields were measured by two homemade suitable probes able to diagnostic fields of high frequency. The field measurements were performed without any specimens inside the line. Being our sample made of living matter, the real field was modified and its value was estimated by a simulation code. The bioluminescence experiments were performed only at 900 MHz for two different measured electric fields, 53 and 140 V/m. The light emission was measured right from the beginning and after 7 and 25 h. Under RF irradiation, we found that the bioluminescence activity decreased. Compared with the control sample, the diminution was 6.8% and 44% after 7 and 25 h of irradiation, respectively, both with the low or high field. No changes of the survival factor for all the samples were observed. Besides, to understand the emission processes, we operated the deconvolution of the spectra by two Gaussian curves. The Gaussian

  20. View facing north (30°) of Transmission Line entering Teton River ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing north (30°) of Transmission Line entering Teton River Valley, near Structure 40-7 - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  1. View facing south (210°) of Transmission Line going over hill, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing south (210°) of Transmission Line going over hill, Structure 46-12 in foreground, near Collins School - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  2. View facing northeast (60°) of Structure 259, other transmission lines ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing northeast (60°) of Structure 25-9, other transmission lines and small farmstead visible in background - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  3. HendersonMead Transmission Line 2 southwest of Boulder City Substation, view ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Henderson-Mead Transmission Line 2 southwest of Boulder City Substation, view southwest - Hoover Dam, Henderson-Mead Transmission Line 2, Spanning Colorado River at Route 93, Boulder City, Clark County, NV

  4. Experimental Observations of a Left-Handed Material That Obeys Snell's Law

    NASA Astrophysics Data System (ADS)

    Houck, Andrew A.; Brock, Jeffrey B.; Chuang, Isaac L.

    2003-04-01

    We measure two-dimensional profiles of collimated microwave beams transmitted through compos­ite wire and split-ring resonator prisms. Prior experiments suggest these structures have a negative index of refraction, though these claims have been questioned. Our 2D measurements demonstrate that transmission obeys Snell's law with a negative index, confirming the refractive nature of this signal and refuting alternatives posed in the criticisms. In addition, we present preliminary evidence that a flat rectangular slab of this material can focus power from a point source.

  5. The structure of Plasmodium vivax phosphatidylethanolamine-binding protein suggests a functional motif containing a left-handed helix

    SciTech Connect

    Arakaki, Tracy; Neely, Helen; Boni, Erica; Mueller, Natasha; Buckner, Frederick S.; Van Voorhis, Wesley C.; Lauricella, Angela; DeTitta, George; Luft, Joseph; Hol, Wim G. J.; Merritt, Ethan A.

    2007-03-01

    The crystal structure of a phosphatidylethanolamine-binding protein from P. vivax, a homolog of Raf-kinase inhibitor protein (RKIP), has been solved to a resolution of 1.3 Å. The inferred interaction surface near the anion-binding site is found to include a distinctive left-handed α-helix. The structure of a putative Raf kinase inhibitor protein (RKIP) homolog from the eukaryotic parasite Plasmodium vivax has been studied to a resolution of 1.3 Å using multiple-wavelength anomalous diffraction at the Se K edge. This protozoan protein is topologically similar to previously studied members of the phosphatidylethanolamine-binding protein (PEBP) sequence family, but exhibits a distinctive left-handed α-helical region at one side of the canonical phospholipid-binding site. Re-examination of previously determined PEBP structures suggests that the P. vivax protein and yeast carboxypeptidase Y inhibitor may represent a structurally distinct subfamily of the diverse PEBP-sequence family.

  6. Can copper(II) mediate Hoogsteen base-pairing in a left-handed DNA duplex? A pulse EPR study.

    PubMed

    Santangelo, Maria Grazia; Antoni, Philipp M; Spingler, Bernhard; Jeschke, Gunnar

    2010-02-22

    Pulse EPR spectroscopy is used to investigate possible structural features of the copper(II) ion coordinated to poly(dG-dC).poly(dG-dC) in a frozen aqueous solution, and the structural changes of the polynucleotide induced by the presence of the metal ion. Two different copper species were identified and their geometry explained by a molecular model. According to this model, one species is exclusively coordinated to a single guanine with the N7 nitrogen atom forming a coordinative bond with the copper. In the other species, a guanine and a cytosine form a ternary complex together with the copper ion. A copper crosslink between the N7 of guanine and N3 of cytosine is proposed as the most probable coordination site. Moreover, no evidence was found for an interaction of either copper species with a phosphate group or equatorial water molecules. In addition, circular dichroism (CD) spectroscopy showed that the DNA of the Cu(II)-poly(dG-dC).poly(dG-dC) adducts resembles the left-handed Z-form. These results suggest that metal-mediated Hoogsteen base pairing, as previously proposed for a right-handed DNA duplex, can also occur in a double-stranded left-handed DNA.

  7. ILQINS hexapeptide, identified in lysozyme left-handed helical ribbons and nanotubes, forms right-handed helical ribbons and crystals.

    PubMed

    Lara, Cecile; Reynolds, Nicholas P; Berryman, Joshua T; Xu, Anqiu; Zhang, Afang; Mezzenga, Raffaele

    2014-03-26

    Amyloid fibrils are implicated in over 20 neurodegenerative diseases. The mechanisms of fibril structuring and formation are not only of medical and biological importance but are also relevant for material science and nanotechnologies due to the unique structural and physical properties of amyloids. We previously found that hen egg white lysozyme, homologous to the disease-related human lysozyme, can form left-handed giant ribbons, closing into nanotubes. By using matrix-assisted laser desorption ionization mass spectrometry analysis, we here identify a key component of such structures: the ILQINS hexapeptide. By combining atomic force microscopy and circular dichorism, we find that this fragment, synthesized by solid-phase peptide synthesis, also forms fibrillar structures in water at pH 2. However, all fibrillar structures formed possess an unexpected right-handed twist, a rare chirality within the corpus of amyloid experimental observations. We confirm by small- and wide-angle X-ray scattering and molecular dynamics simulations that these fibrils are composed of conventional left-handed β-sheets, but that packing stresses between adjacent sheets create this twist of unusual handedness. We also show that the right-handed fibrils represent a metastable state toward β-sheet-based microcrystals formation.

  8. Field quality measurements of a 2-Tesla transmission line magnet

    SciTech Connect

    Velev, G.V.; Foster, W.; Kashikhin, V.; Mazur, P.; Oleck, A.; Piekarz, H.; Schlabach, P.; Sylvester, C.; Wake, M.; /KEK, Tsukuba

    2005-09-01

    A prototype 2-Tesla superconducting transmission line magnet for future hadron colliders was designed, built and tested at Fermilab. The 1.5 m long, combined-function gradient-dipole magnet has a vertical pole aperture of 20 mm. To measure the magnetic field quality in such a small magnet aperture, a specialized rotating coil of 15.2 mm diameter, 0.69 m long was fabricated. Using this probe, a program of magnetic field quality measurements was successfully performed. Results of the measurements are presented and discussed.

  9. LineCast: line-based distributed coding and transmission for broadcasting satellite images.

    PubMed

    Wu, Feng; Peng, Xiulian; Xu, Jizheng

    2014-03-01

    In this paper, we propose a novel coding and transmission scheme, called LineCast, for broadcasting satellite images to a large number of receivers. The proposed LineCast matches perfectly with the line scanning cameras that are widely adopted in orbit satellites to capture high-resolution images. On the sender side, each captured line is immediately compressed by a transform-domain scalar modulo quantization. Without syndrome coding, the transmission power is directly allocated to quantized coefficients by scaling the coefficients according to their distributions. Finally, the scaled coefficients are transmitted over a dense constellation. This line-based distributed scheme features low delay, low memory cost, and low complexity. On the receiver side, our proposed line-based prediction is used to generate side information from previously decoded lines, which fully utilizes the correlation among lines. The quantized coefficients are decoded by the linear least square estimator from the received data. The image line is then reconstructed by the scalar modulo dequantization using the generated side information. Since there is neither syndrome coding nor channel coding, the proposed LineCast can make a large number of receivers reach the qualities matching their channel conditions. Our theoretical analysis shows that the proposed LineCast can achieve Shannon's optimum performance by using a high-dimensional modulo-lattice quantization. Experiments on satellite images demonstrate that it achieves up to 1.9-dB gain over the state-of-the-art 2D broadcasting scheme and a gain of more than 5 dB over JPEG 2000 with forward error correction.

  10. 50 CFR 29.21-8 - Electric power transmission line rights-of-way.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 50 Wildlife and Fisheries 8 2011-10-01 2011-10-01 false Electric power transmission line rights-of... General Regulations § 29.21-8 Electric power transmission line rights-of-way. By accepting a right-of-way for a power transmission line, the applicant thereby agrees and consents to comply with and be...

  11. 50 CFR 29.21-8 - Electric power transmission line rights-of-way.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 50 Wildlife and Fisheries 9 2013-10-01 2013-10-01 false Electric power transmission line rights-of... General Regulations § 29.21-8 Electric power transmission line rights-of-way. By accepting a right-of-way for a power transmission line, the applicant thereby agrees and consents to comply with and be...

  12. 50 CFR 29.21-8 - Electric power transmission line rights-of-way.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 50 Wildlife and Fisheries 9 2014-10-01 2014-10-01 false Electric power transmission line rights-of... General Regulations § 29.21-8 Electric power transmission line rights-of-way. By accepting a right-of-way for a power transmission line, the applicant thereby agrees and consents to comply with and be...

  13. 50 CFR 29.21-8 - Electric power transmission line rights-of-way.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 50 Wildlife and Fisheries 9 2012-10-01 2012-10-01 false Electric power transmission line rights-of... General Regulations § 29.21-8 Electric power transmission line rights-of-way. By accepting a right-of-way for a power transmission line, the applicant thereby agrees and consents to comply with and be...

  14. 49 CFR 192.713 - Transmission lines: Permanent field repair of imperfections and damages.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Maintenance § 192.713 Transmission lines: Permanent field repair of imperfections and damages. (a) Each imperfection or damage that impairs the serviceability of pipe in a steel transmission line operating at or... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Permanent field repair...

  15. Estimating Magnetic Fields of Homes Near Transmission Lines in the California Power Line Study

    PubMed Central

    Vergara, Ximena P.; Kavet, Robert; Crespi, Catherine M.; Hooper, Chris; Silva, J. Michael; Kheifets, Leeka

    2015-01-01

    The California Power Line Study is a case-control study investigating the relation between residences near transmission lines and risk of childhood leukemia. It includes 5788 childhood leukemia cases and 5788 matched primary controls born between 1986 and 2007. We describe the methodology for estimating magnetic fields at study residences as well as for characterizing sources of uncertainty in these estimates. Birth residences of study subjects were geocoded and their distances to transmission lines were ascertained. 302 residences were deemed sufficiently close to transmission lines to have non-zero magnetic fields attributable to the lines. These residences were visited and detailed data, describing the physical configuration and dimensions of the lines contributing to the magnetic field at the residence, were collected. Phasing, loading, and directional load flow data for years of birth and diagnosis for each subject as well as for the day of site visit were obtained from utilities when available; when yearly average load for a particular year was not available, extrapolated values based on expert knowledge and prediction models were obtained. These data were used to estimate the magnetic fields at the center, closest and farthest point of each residence. We found good correlation between calculated fields and spot measurements of fields taken on site during visits. Our modeling strategies yielded similar calculated field estimates, and they were in high agreement with utility extrapolations. Phasing was known for over 90% of the lines. Important sources of uncertainty included a lack of information on the precise location of residences located within apartment buildings or other complexes. Our findings suggest that we were able to achieve high specificity in exposure assessment, which is essential for examining the association between distance to or magnetic fields from power lines and childhood leukemia risk. PMID:26005950

  16. Single-wire radio frequency transmission lines in biological tissue

    NASA Astrophysics Data System (ADS)

    Besnoff, Jordan S.; Reynolds, Matthew S.

    2015-05-01

    We present an approach for implanting radio frequency transmission lines in biological tissue, using a single insulated wire surrounded by tissue as a variant of the Goubau single-wire transmission line (SWTL) in air. We extend the Goubau SWTL model to include SWTLs surrounded by lossy dielectrics such as tissue by assuming a propagating mode component in the tissue. We show that a thin wire of radius 63.5 μ m , coated with biocompatible fluorinated ethylene propylene dielectric, exhibits a measured loss of only 1 dB/cm at a frequency of 915 MHz. The model fit to the measured insertion loss is within ±0.3 dB/cm across the 100 MHz to 3 GHz band. This SWTL presents excellent impedance matching to 50 Ω as evidenced by a measured median return loss better than 10 dB across the 100 MHz to 3 GHz range. This approach represents an alternative to near-field magnetic coupling for implanted systems where tissue displacement by a single, thin wire can be tolerated.

  17. Smaller-loss planar SPP transmission line than conventional microstrip in microwave frequencies

    PubMed Central

    Zhang, Hao Chi; Zhang, Qian; Liu, Jun Feng; Tang, Wenxuan; Fan, Yifeng; Cui, Tie Jun

    2016-01-01

    Transmission line is a basic component in all passive devices, integrated circuits, and systems. Microstrip is the most popular transmission line in the microwave and millimeter-wave frequencies, and has been widely used in current electronic devices, circuits, and systems. One of the important issues to be solved in such applications is the relatively large transmission loss of microstrip. Here, we propose a method to reduce the loss of microwave transmission line based on the designable wavenumber of spoof surface plasmon polaritons (SPPs). Using this characteristic, we analyze and experimentally demonstrate the low-loss feature of the SPP transmission line through the perturbation method and S-parameter measurements, respectively. Both simulation and experimental results show that the SPP transmission line has much smaller transmission loss than traditional microstrip with the same size in the microwave frequencies. Hence, the spoof SPP transmission line may make a big step forward in the low-loss circuits and systems. PMID:26983911

  18. Zero absorption and a large negative refractive index in a left-handed four-level atomic medium

    NASA Astrophysics Data System (ADS)

    Zhao, Shuncai; Liu, Zhengdong; Wu, Qixuan

    2010-02-01

    In this paper, we have investigated three external fields interacting with the four-level atomic system described by the density-matrix approach. The atomic system exhibits left-handedness with zero absorption and large negative refractive index. Varying the parameters of the three external fields, the properties of zero absorption and large negative refractive index from the atomic system remain unvarying. Our scheme proposes an approach to obtain a negative refractive medium with zero absorption. The zero absorption property of the atomic system may be used to amplify the evanescent waves that have been lost in the imaging by traditional lenses, and a slab fabricated by the left-handed atomic system may be an ideal candidate for designing perfect lenses.

  19. Numerical study on a three-dimensional broadband isotropic left-handed metamaterial based on closed rings

    NASA Astrophysics Data System (ADS)

    Fang, Fang; Cheng, Yongzhi; Liao, Honghua

    2014-02-01

    In this paper, a three-dimensional (3D) broadband isotropic left-handed metamaterial (LHM) is proposed and investigated numerically. The 3D unit cell is composed of a dielectric cube with metallic closed rings (CRs) printed on all its six sides. Simulations of the electric field and surface current distributions, the effective electromagnetic (EM) parameter retrieval and a refraction phenomenon based on a wedge-shaped model were carried out to further verify the LH properties of the proposed 3D CRs structure model. The results show that the relative bandwidth is more than 6 GHz, and the LH band is polarization independent and almost unchanged for different incident angles. Moreover, the EM parameters of the unit cell with different geometrical parameters are also explored in order to obtain an optimized design for 3D LHM.

  20. Electro-optically generating and controlling right- and left-handed circularly polarized multiring modes of light beams.

    PubMed

    Zhu, Wenguo; She, Weilong

    2012-07-15

    We propose a simple method for generating and controlling right- and left-handed circularly polarized (RHP and LHP) multiring modes of light beams by means of Pockels effect in a single strontium barium niobate (SBN) crystal. The numerical results show that an LHP Laguerre-Gaussian LG(0l) beam, propagating along the optical axis of the crystal, will partly turn into an RHP vortex light field of order l+2. Moreover, a pair of the LHP and RHP components of the output light field is LG-like modes sharing an identically radial index, which is electro-optically controllable. The power ratio between these two components depends on the applied electric field and the mode of input beam.

  1. Wild Horse 69-kV transmission line environmental assessment

    SciTech Connect

    1996-12-01

    Hill County Electric Cooperative Inc. (Hill County) proposes to construct and operate a 69-kV transmission line from its North Gildford Substation in Montana north to the Canadian border. A vicinity project area map is enclosed as a figure. TransCanada Power Corporation (TCP), a Canadian power-marketing company, will own and construct the connecting 69-kV line from the international border to Express Pipeline`s pump station at Wild Horse, Alberta. This Environmental Assessment is prepared for the Department of Energy (DOE) as lead federal agency to comply with the requirements of the National Environmental Policy Act (NEPA), as part of DOE`s review and approval process of the applications filed by Hill County for a DOE Presidential Permit and License to Export Electricity to a foreign country. The purpose of the proposed line is to supply electric energy to a crude oil pump station in Canada, owned by Express Pipeline Ltd. (Express). The pipeline would transport Canadian-produced oil from Hardisty, Alberta, Canada, to Caster, Wyoming. The Express Pipeline is scheduled to be constructed in 1996--97 and will supply crude oil to refineries in Wyoming and the midwest.

  2. Material selection of a ferrimagnetic loaded coaxial delay line for phasing gyromagnetic nonlinear transmission lines.

    PubMed

    Johnson, J M; Reale, D V; Cravey, W H; Garcia, R S; Barnett, D H; Neuber, A A; Dickens, J C; Mankowski, J J

    2015-08-01

    Implementing nonlinear transmission line (NLTL) technology in the design of a high power microwave source has the benefits of producing a comparatively small and lightweight solid-state system where the emission frequency is easily tuned. Usually, smaller in physical size, single NLTLs may produce significantly less power than its vacuum based counterparts. However, combining individual NLTL outputs electrically or in free-space is an attractive solution to achieve greater output power. This paper discusses a method for aligning a four element NLTL antenna array with coaxial geometry using easily adjustable temporal delay lines. These delay lines, sometimes referred to as pulse shock lines or pulse sharpening lines, are placed serially in front of the main NLTL line. The propagation velocity in each delay line is set by the voltage amplitude of an incident pulse as well as the magnetic field bias. Each is adjustable although for the system described in this paper, the voltage is held constant while the bias is changed through applying an external DC magnetic field of varying magnitude. Three different ferrimagnetic materials are placed in the temporal delay line to evaluate which yields the greatest range of electrical delay with the least amount of variability from consecutive shots. PMID:26329216

  3. Protein loops, solitons, and side-chain visualization with applications to the left-handed helix region

    NASA Astrophysics Data System (ADS)

    Lundgren, Martin; Niemi, Antti J.; Sha, Fan

    2012-06-01

    Folded proteins have a modular assembly. They are constructed from regular secondary structures like α helices and β strands that are joined together by loops. Here we develop a visualization technique that is adapted to describe this modular structure. In complement to the widely employed Ramachandran plot that is based on toroidal geometry, our approach utilizes the geometry of a two sphere. Unlike the more conventional approaches that describe only a given peptide unit, ours is capable of describing the entire backbone environment including the neighboring peptide units. It maps the positions of each atom to the surface of the two-sphere exactly how these atoms are seen by an observer who is located at the position of the central Cα atom. At each level of side-chain atoms we observe a strong correlation between the positioning of the atom and the underlying local secondary structure with very little if any variation between the different amino acids. As a concrete example we analyze the left-handed helix region of nonglycyl amino acids. This region corresponds to an isolated and highly localized residue independent sector in the direction of the Cβ carbons on the two-sphere. We show that the residue independent localization extends to Cγ and Cδ carbons and to side-chain oxygen and nitrogen atoms in the case of asparagine and aspartic acid. When we extend the analysis to the side-chain atoms of the neighboring residues, we observe that left-handed β turns display a regular and largely amino acid independent structure that can extend to seven consecutive residues. This collective pattern is due to the presence of a backbone soliton. We show how one can use our visualization techniques to analyze and classify the different solitons in terms of selection rules that we describe in detail.

  4. ParA2, a Vibrio cholerae chromosome partitioning protein, forms left-handed helical filaments on DNA.

    PubMed

    Hui, Monica P; Galkin, Vitold E; Yu, Xiong; Stasiak, Alicja Z; Stasiak, Andrzej; Waldor, Matthew K; Egelman, Edward H

    2010-03-01

    Most bacterial chromosomes contain homologs of plasmid partitioning (par) loci. These loci encode ATPases called ParA that are thought to contribute to the mechanical force required for chromosome and plasmid segregation. In Vibrio cholerae, the chromosome II (chrII) par locus is essential for chrII segregation. Here, we found that purified ParA2 had ATPase activities comparable to other ParA homologs, but, unlike many other ParA homologs, did not form high molecular weight complexes in the presence of ATP alone. Instead, formation of high molecular weight ParA2 polymers required DNA. Electron microscopy and three-dimensional reconstruction revealed that ParA2 formed bipolar helical filaments on double-stranded DNA in a sequence-independent manner. These filaments had a distinct change in pitch when ParA2 was polymerized in the presence of ATP versus in the absence of a nucleotide cofactor. Fitting a crystal structure of a ParA protein into our filament reconstruction showed how a dimer of ParA2 binds the DNA. The filaments formed with ATP are left-handed, but surprisingly these filaments exert no topological changes on the right-handed B-DNA to which they are bound. The stoichiometry of binding is one dimer for every eight base pairs, and this determines the geometry of the ParA2 filaments with 4.4 dimers per 120 A pitch left-handed turn. Our findings will be critical for understanding how ParA proteins function in plasmid and chromosome segregation.

  5. Protein loops, solitons, and side-chain visualization with applications to the left-handed helix region.

    PubMed

    Lundgren, Martin; Niemi, Antti J; Sha, Fan

    2012-06-01

    Folded proteins have a modular assembly. They are constructed from regular secondary structures like α helices and β strands that are joined together by loops. Here we develop a visualization technique that is adapted to describe this modular structure. In complement to the widely employed Ramachandran plot that is based on toroidal geometry, our approach utilizes the geometry of a two sphere. Unlike the more conventional approaches that describe only a given peptide unit, ours is capable of describing the entire backbone environment including the neighboring peptide units. It maps the positions of each atom to the surface of the two-sphere exactly how these atoms are seen by an observer who is located at the position of the central C_{α} atom. At each level of side-chain atoms we observe a strong correlation between the positioning of the atom and the underlying local secondary structure with very little if any variation between the different amino acids. As a concrete example we analyze the left-handed helix region of nonglycyl amino acids. This region corresponds to an isolated and highly localized residue independent sector in the direction of the C_{β} carbons on the two-sphere. We show that the residue independent localization extends to C_{γ} and C_{δ} carbons and to side-chain oxygen and nitrogen atoms in the case of asparagine and aspartic acid. When we extend the analysis to the side-chain atoms of the neighboring residues, we observe that left-handed β turns display a regular and largely amino acid independent structure that can extend to seven consecutive residues. This collective pattern is due to the presence of a backbone soliton. We show how one can use our visualization techniques to analyze and classify the different solitons in terms of selection rules that we describe in detail.

  6. Fuzzy logic based on-line fault detection and classification in transmission line.

    PubMed

    Adhikari, Shuma; Sinha, Nidul; Dorendrajit, Thingam

    2016-01-01

    This study presents fuzzy logic based online fault detection and classification of transmission line using Programmable Automation and Control technology based National Instrument Compact Reconfigurable i/o (CRIO) devices. The LabVIEW software combined with CRIO can perform real time data acquisition of transmission line. When fault occurs in the system current waveforms are distorted due to transients and their pattern changes according to the type of fault in the system. The three phase alternating current, zero sequence and positive sequence current data generated by LabVIEW through CRIO-9067 are processed directly for relaying. The result shows that proposed technique is capable of right tripping action and classification of type of fault at high speed therefore can be employed in practical application. PMID:27398278

  7. Fuzzy logic based on-line fault detection and classification in transmission line.

    PubMed

    Adhikari, Shuma; Sinha, Nidul; Dorendrajit, Thingam

    2016-01-01

    This study presents fuzzy logic based online fault detection and classification of transmission line using Programmable Automation and Control technology based National Instrument Compact Reconfigurable i/o (CRIO) devices. The LabVIEW software combined with CRIO can perform real time data acquisition of transmission line. When fault occurs in the system current waveforms are distorted due to transients and their pattern changes according to the type of fault in the system. The three phase alternating current, zero sequence and positive sequence current data generated by LabVIEW through CRIO-9067 are processed directly for relaying. The result shows that proposed technique is capable of right tripping action and classification of type of fault at high speed therefore can be employed in practical application.

  8. A computer code to calculate line by line atmospheric transmission spectra on a microcomputer

    NASA Astrophysics Data System (ADS)

    Safren, H. G.

    1987-07-01

    A computer program is described which calculates line by line atmospheric transmission spectra on a microcomputer. Radiance calculations are not included. The program is written in FORTRAN and could be modified to run on a microcomputer other than the one on which it was implemented, except that the plotting routine would have to be replaced. The program is based on the 1978 Air Force Geophysics Laboratory LASER routine, and uses absorption line data from the 1982 update of the AFGL Atmospheric Absorption Line Parameters Compilation; segments of needed line data are taken from the tape, preprocessed into the form used by the program and stored on floppy disks. The program calculates transmission spectra over a variety of paths and spanning an arbitrarily chosen wavelength or frequency range; the path may be chosen to be horizontal, vertical or slanted at any zenith angle, and may extend between any two altitudes between 0 and 15 km. Aerosol effects are included, presently based on the 1976 Shettle and Fenn models, plus some molecular continuum effects and Rayleigh scattering.

  9. Gas insulated transmission line having low inductance intercalated sheath

    DOEpatents

    Cookson, Alan H.

    1978-01-01

    A gas insulated transmission line including an outer sheath, an inner conductor disposed within the outer sheath, and an insulating gas between the inner conductor and the outer sheath. The outer sheath comprises an insulating tube having first and second ends, and having interior and exterior surfaces. A first electrically conducting foil is secured to the interior surface of the insulating tube, is spirally wound from one tube end to the second tube end, and has a plurality of overlapping turns. A second electrically conducting foil is secured to the exterior surface of the insulating tube, and is spirally wound in the opposite direction from the first electrically conducting foil. By winding the foils in opposite directions, the inductances within the intercalated sheath will cancel each other out.

  10. Monolithic high voltage nonlinear transmission line fabrication process

    DOEpatents

    Cooper, Gregory A.

    1994-01-01

    A process for fabricating sequential inductors and varactor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varactor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process.

  11. Monolithic high voltage nonlinear transmission line fabrication process

    DOEpatents

    Cooper, G.A.

    1994-10-04

    A process for fabricating sequential inductors and varistor diodes of a monolithic, high voltage, nonlinear, transmission line in GaAs is disclosed. An epitaxially grown laminate is produced by applying a low doped active n-type GaAs layer to an n-plus type GaAs substrate. A heavily doped p-type GaAs layer is applied to the active n-type layer and a heavily doped n-type GaAs layer is applied to the p-type layer. Ohmic contacts are applied to the heavily doped n-type layer where diodes are desired. Multiple layers are then either etched away or Oxygen ion implanted to isolate individual varistor diodes. An insulator is applied between the diodes and a conductive/inductive layer is thereafter applied on top of the insulator layer to complete the process. 6 figs.

  12. Nonlinear galloping of internally resonant iced transmission lines considering eccentricity

    NASA Astrophysics Data System (ADS)

    Yan, Zhimiao; Yan, Zhitao; Li, Zhengliang; Tan, Ting

    2012-07-01

    Based on the curved-beam theory, a nonlinear galloping model considering three displacement (normal, bi-normal and tangential) components and twist is formulated. According to the property of transmission line, one reduced (normal and bi-normal) galloping model, with regard of bending, rotation and eccentricity of cross section, is obtained. Moreover, the initial rotation angle is also introduced in galloping and aerodynamic models. Additionally, based on the reduced model, the bifurcation and stability of the two cases (1:1 resonance and 2:1 resonance) are analyzed. The results turn out that the importance of ice eccentricity needs to be highlighted. Finally, multiple stabilities are found through the analyses of bifurcation and stability and proved by the reduced model and Reduced Amplitude Modulation Equations (RAME) numerically integrated in time history.

  13. Microwave transmission line dielectric probe to detect biomolecular surface interactions.

    PubMed

    Chen, Qin; McMurdie, Joey; Roitman, Daniel; Knoesen, Andre

    2004-01-01

    A probe was developed to detect biomolecular binding events at a liquid-solid interface in the microwave regime in real time and without using fluorescence labels. The probe consists of a coplanar transmission line (CTL) fabricated on a glass slide that can detect dielectric changes in close proximity of the interface. The CTL geometry concentrates the electric flux density in the gap region between the signal and ground electrodes and makes it very sensitive to permittivity changes at the liquid-solid interface. The probe operation was demonstrated by immobilizing protein A on the glass surface and detecting rabbit IgG molecules in a flow channel. The sensitivity was conservatively estimated to be 100 pg/mm(2).

  14. Transmission line corona losses under hoar frost conditions

    SciTech Connect

    Lahti, K.; Nousiainen, K.; Lahtinen, M.

    1997-04-01

    Transmission line corona losses under hoar frost conditions were studied in the climate room of the high voltage laboratory of Tampere University of Technology. The measurements were performed using a coaxial measurement arrangement with different bundle and conductor types. The effects of conductor and bundle type, temperature, applied voltage and hoar frost thickness on corona losses were investigated. A two-conductor bundle had corona losses about 2.5--5 times higher than a three-conductor bundle. Relatively thin hoar frosts were used in the tests. Even the thinnest hoar frost resulted in remarkable corona losses and the losses were very sensitive to changes in the hoar frost thickness. The ambient temperature had a strong influence on the measured losses.

  15. Tailoring of electron flow current in magnetically insulated transmission lines

    NASA Astrophysics Data System (ADS)

    Martin, J. P.; Savage, M. E.; Pointon, T. D.; Gilmore, M. A.

    2009-03-01

    It is desirable to optimize (minimizing both the inductance and electron flow) the magnetically insulated vacuum sections of low impedance pulsed-power drivers. The goal of low inductance is understandable from basic efficiency arguments. The goal of low electron flow results from two observations: (1) flowing electrons generally do not deliver energy to (or even reach) most loads, and thus constitute a loss mechanism; (2) energetic electrons deposited in a small area can cause anode damage and anode plasma formation. Low inductance and low electron flow are competing goals; an optimized system requires a balance of the two. While magnetically insulated systems are generally forgiving, there are times when optimization is crucial. For example, in large pulsed-power drivers used to energize high energy density physics loads, the electron flow as a fraction of total current is small, but that flow often reaches the anode in relatively small regions. If the anode temperature becomes high enough to desorb gas, the resulting plasma initiates a gap closure process that can impact system performance. Magnetic-pressure driven (z pinches and material equation of state) loads behave like a fixed inductor for much of the drive pulse. It is clear that neither fixed gap nor constant-impedance transmission lines are optimal for driving inductive loads. This work shows a technique for developing the optimal impedance profile for the magnetically insulated section of a high-current driver. Particle-in-cell calculations are used to validate the impedance profiles developed in a radial disk magnetically insulated transmission line geometry. The input parameters are the spacing and location of the minimum gap, the effective load inductance, and the desired electron flow profile. The radial electron flow profiles from these simulations are in good agreement with theoretical predictions when driven at relatively high voltage (i.e., V≥2MV).

  16. Modeling graphite anodes with serial and transmission line models

    NASA Astrophysics Data System (ADS)

    Illig, J.; Ender, M.; Weber, A.; Ivers-Tiffée, E.

    2015-05-01

    Electrochemical impedance spectroscopy (EIS) is an indispensable technique for the investigation of polarization processes in Lithium-ion Batteries. These cause performance limitation or degradation. A physically meaningful impedance model is key when drawing conclusions on further cell improvement. This study introduces an in-depth impedance analysis of a commercial high-power graphite anode. The impedance spectra measured between 0 °C and 30 °C and 0%-100% SOC were analyzed by the distribution of relaxation times (DRT-method), enabling a separation of loss processes by their individual time constants. Using this method, we separated charge transfer resistance and solid electrolyte interface resistance at medium frequencies (10 Hz-200 Hz) and the contact resistance anode/current collector in the at high frequency range (5 kHz-100 kHz). Two fundamentally different model structures were set up, either (i) two modifications of a serial model connecting RQ-elements and a Warburg element for solid state diffusion, or (ii) three modifications of a transmission line model with one-path or two-path design. The suitability of all serial and TLM model structures was tested, and the fitting procedure was supported using microstructure parameters gained from x-ray tomography. The favored one-path transmission line model reveals that the lithium-ion transport in the electrolyte contributes more to polarization than expected. Impediment of lithium-ion transport is caused by the pore structure and the tortuosity of the high-power graphite anode, and has to be considered for meaningful interpretation of impedance spectra.

  17. 49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission...

  18. 49 CFR 192.711 - Transmission lines: General requirements for repair procedures.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... Maintenance § 192.711 Transmission lines: General requirements for repair procedures. (a) Temporary repairs... 49 Transportation 3 2010-10-01 2010-10-01 false Transmission lines: General requirements for..., imperfection, or damage that impairs its serviceability is found in a segment of steel transmission...

  19. 49 CFR 192.711 - Transmission lines: General requirements for repair procedures.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: General requirements for... Maintenance § 192.711 Transmission lines: General requirements for repair procedures. (a) Temporary repairs..., imperfection, or damage that impairs its serviceability is found in a segment of steel transmission...

  20. 49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Transmission lines: Permanent field repair of... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable under § 192.241(c) must be repaired as follows: (a) If it is feasible to take the segment of transmission...

  1. Polar On-Line Acquisition Relay and Transmission System (POLARATS)

    SciTech Connect

    Yuracko, K.

    2004-07-15

    POLARATS (Polar On-Line Acquisition Relay And Transmission System) is being developed by YAHSGS LLC (YAHSGS) and Oak Ridge National Laboratory (ORNL) to provide remote, unattended monitoring of environmental parameters under harsh environmental conditions. In particular, instrumental design and engineering is oriented towards protection of human health in the Arctic, and with the additional goal of advancing Arctic education and research. POLARATS will obtain and transmit environmental data from hardened monitoring devices deployed in locations important to understanding atmospheric and aquatic pollutant migration as it is biomagnified in Arctic food chains. An Internet- and personal computer (PC)-based educational module will provide real time sensor data, on-line educational content, and will be integrated with workbooks and textbooks for use in middle and high school science programs. The educational elements of POLARATS include an Internet-based educational module that will instruct students in the use of the data and how those data fit into changing Arctic environments and food chains. POLARATS will: (1) Enable students, members of the community, and scientific researchers to monitor local environmental conditions in real time over the Internet; and (2) Provide additional educational benefits through integration with middle- and high-school science curricula. Information will be relayed from POLARATS devices to classrooms and libraries along with custom-designed POLARATS teaching materials that will be integrated into existing curricula to enhance the educational benefits realized from the information obtained.

  2. Left-Handed Connections.

    ERIC Educational Resources Information Center

    Lipson, Alice M.

    1984-01-01

    The following aspects of left-handedness are discussed: etiology and associated learning and developmental disorders; right-brain dominance and how to detect it; adaptations to the physical learning environment; behavior patterns; and teaching techniques. (JW)

  3. 49 CFR 236.73 - Open-wire transmission line; clearance to other circuits.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Open-wire transmission line; clearance to other... line; clearance to other circuits. Open-wire transmission line operating at voltage of 750 volts or... THE INSTALLATION, INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS,...

  4. Effects of high-voltage transmission lines on honeybees

    SciTech Connect

    Greenberg, B.; Bindokas, V.P.; Gauger, J.R.

    1985-05-01

    When shielded and exposed colonies were placed at incremental distances at a right angle from a 760-kV transmission line different thresholds for biologic effects were obtained. Hive exposures were controlled (E-field: 7, 5.5, 4.1, 1.8, and 0.65 to 0.85 kV/m) by variable height current collectors; shielded hives under the line behave normally. Exposure to 7 kV/m can produce the following sequence of events: (1) increased motor activity and transient hive temperature increase; (2) abnormal propolization; (3) retarded hive weight gain; (4) excess queen cell production with queen loss; (5) reduction of sealed brood area; and (6) poor winter survival. No biological effects were detected below 4.1 kV/m, thus the ''biological effects corridor'' is limited to approximately 23 m beyond a ground projection of each outer phase wire. Hive architecture enhances E-fields and creates shock hazards for bees. Intra-hive E-fields (15 to 100+ kV/m) were measured with a displacement current sensor and fiber optic telemetry link. Step-potential-induced currents up to 0.5 uA were measured with a bee model in hives at 7 kV/m. To investigate further the role of shock versus electric field exposure the study was continued to develop hive entrance extensions (porches), which produce controlled bee exposure to E-field or shock, and to test the feasibility of using these porches in such a study. Biological effects (e.g., abnormal propolization, retarded hive weight, queen loss) found in colonies with total-hive exposure were produced by entrance-only exposure of adult bees. We now have an exposure system in which E-field and shock can be separately controlled to reproduce the biological effects. 10 refs.

  5. 49 CFR 192.717 - Transmission lines: Permanent field repair of leaks.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... encirclement welded split sleeve of appropriate design, unless the transmission line is joined by mechanical... method that reliable engineering tests and analyses show can permanently restore the serviceability...

  6. Requirements for self-magnetically insulated transmission lines

    SciTech Connect

    VanDevender, J. Pace; Pointon, Timothy D.; Seidel, David B.; Struve, Kenneth W.; Jennings, Christopher; Oliver, Bryan V.; Schneider, Larry X.

    2015-03-01

    Self-magnetically insulated transmission lines (MITLs) connect pulsed-power drivers with a load. Although the technology was originally developed in the 1970s and is widely used today in super power generators, failure of the technology is the principal limitation on the power that can be delivered to an experiment. We address issues that are often overlooked, rejected after inadequate simulations, or covered by overly conservative assumptions: (i) electron retrapping in coupling MITLs to loads, (ii) the applicability of collisionless versus collisional electron flow, (iii) power transport efficiency as a function of the geometry at the beginning of the MITL, (iv) gap closure and when gap closure can be neglected, and (v) the role of negative ions in causing anode plasmas and enhancing current losses. We suggest a practical set of conservative design requirements for self-magnetically insulated electron flow based on the results discussed in this paper and on previously published results. The requirements are not necessarily severe constraints in all MITL applications; however, each of the 18 suggested requirements should be examined in the design of a MITL and in the investigation of excessive losses.

  7. Precision electron flow measurements in a disk transmission line.

    SciTech Connect

    Clark, Waylon T.; Pelock, Michael D.; Martin, Jeremy Paul; Jackson, Daniel Peter Jr.; Savage, Mark Edward; Stoltzfus, Brian Scott; Mendel, Clifford Will, Jr.; Pointon, Timothy David

    2008-01-01

    An analytic model for electron flow in a system driving a fixed inductive load is described and evaluated with particle in cell simulations. The simple model allows determining the impedance profile for a magnetically insulated transmission line given the minimum gap desired, and the lumped inductance inside the transition to the minimum gap. The model allows specifying the relative electron flow along the power flow direction, including cases where the fractional electron flow decreases in the power flow direction. The electrons are able to return to the cathode because they gain energy from the temporally rising magnetic field. The simulations were done with small cell size to reduce numerical heating. An experiment to compare electron flow to the simulations was done. The measured electron flow is {approx}33% of the value from the simulations. The discrepancy is assumed to be due to a reversed electric field at the cathode because of the inductive load and falling electron drift velocity in the power flow direction. The simulations constrain the cathode electric field to zero, which gives the highest possible electron flow.

  8. INSTRUMENTATION FOR SURVEYING ACOUSTIC SIGNALS IN NATURAL GAS TRANSMISSION LINES

    SciTech Connect

    John L. Loth; Gary J. Morris; George M. Palmer; Richard Guiler; Deepak Mehra

    2003-09-01

    In the U.S. natural gas is distributed through more than one million miles of high-pressure transmission pipelines. If all leaks and infringements could be detected quickly, it would enhance safety and U.S. energy security. Only low frequency acoustic waves appear to be detectable over distances up to 60 km where pipeline shut-off valves provide access to the inside of the pipeline. This paper describes a Portable Acoustic Monitoring Package (PAMP) developed to record and identify acoustic signals characteristic of: leaks, pump noise, valve and flow metering noise, third party infringement, manual pipeline water and gas blow-off, etc. This PAMP consists of a stainless steel 1/2 inch NPT plumbing tree rated for use on 1000 psi pipelines. Its instrumentation is designed to measure acoustic waves over the entire frequency range from zero to 16,000 Hz by means of four instruments: (1) microphone, (2) 3-inch water full range differential pressure transducer with 0.1% of range sensitivity, (3) a novel 3 inch to 100 inch water range amplifier, using an accumulator with needle valve and (4) a line-pressure transducer. The weight of the PAMP complete with all accessories is 36 pounds. This includes a remote control battery/switch box assembly on a 25-foot extension chord, a laptop data acquisition computer on a field table and a sun shield.

  9. Radial transmission line analysis of multi-layer structures

    SciTech Connect

    Hahn, H.; Hammons, L.

    2011-03-28

    The analysis of multi-layer beam tubes is a standard problem and involves axially propagating waves. This treatment is ill suited to a short multi-layer structure such as the present example of a ferrite covered ceramic break in the beam tube at the ERL photo-cathode electron gun. This paper demonstrates that such structure can better be treated by radial wave propagation. The theoretical method is presented and numerical results are compared with measured network analyser data and Microwave Studio generated simulations. The results confirm the concept of radial transmission lines as a valid analytical method. An Energy Recovery Linac (ERL) is being constructed at this laboratory for the purpose of research towards an envisioned Electron Ion Collider. One of the pertinent topics is damping of Higher Order Modes (HOM). In this ERL, the damping is provided by ferrite absorbers in the beam tube. A modified version thereof, a ceramic break surrounded by ferrite, is planed for the superconducting electron gun. The damper here is located at room temperature just outside of the gun. If used in a cavity chain, the ceramic break is in the vacuum tube at helium temperature whereas the ferrite is moved into the cryostat insulating vacuum allowing higher temperatures. The general properties of the ferrite HOM dampers have been published but are more detailed in this paper.

  10. Requirements for self-magnetically insulated transmission lines

    DOE PAGES

    VanDevender, J. Pace; Pointon, Timothy D.; Seidel, David B.; Struve, Kenneth W.; Jennings, Christopher; Oliver, Bryan V.; Schneider, Larry X.

    2015-03-01

    Self-magnetically insulated transmission lines (MITLs) connect pulsed-power drivers with a load. Although the technology was originally developed in the 1970s and is widely used today in super power generators, failure of the technology is the principal limitation on the power that can be delivered to an experiment. We address issues that are often overlooked, rejected after inadequate simulations, or covered by overly conservative assumptions: (i) electron retrapping in coupling MITLs to loads, (ii) the applicability of collisionless versus collisional electron flow, (iii) power transport efficiency as a function of the geometry at the beginning of the MITL, (iv) gap closuremore » and when gap closure can be neglected, and (v) the role of negative ions in causing anode plasmas and enhancing current losses. We suggest a practical set of conservative design requirements for self-magnetically insulated electron flow based on the results discussed in this paper and on previously published results. The requirements are not necessarily severe constraints in all MITL applications; however, each of the 18 suggested requirements should be examined in the design of a MITL and in the investigation of excessive losses.« less

  11. Unraveling mysteries of personal performance style; biomechanics of left-hand position changes (shifting) in violin performance.

    PubMed

    Visentin, Peter; Li, Shiming; Tardif, Guillaume; Shan, Gongbing

    2015-01-01

    Instrumental music performance ranks among the most complex of learned human behaviors, requiring development of highly nuanced powers of sensory and neural discrimination, intricate motor skills, and adaptive abilities in a temporal activity. Teaching, learning and performing on the violin generally occur within musico-cultural parameters most often transmitted through aural traditions that include both verbal instruction and performance modeling. In most parts of the world, violin is taught in a manner virtually indistinguishable from that used 200 years ago. The current study uses methods from movement science to examine the "how" and "what" of left-hand position changes (shifting), a movement skill essential during violin performance. In doing so, it begins a discussion of artistic individualization in terms of anthropometry, the performer-instrument interface, and the strategic use of motor behaviors. Results based on 540 shifting samples, a case series of 6 professional-level violinists, showed that some elements of the skill were individualized in surprising ways while others were explainable by anthropometry, ergonomics and entrainment. Remarkably, results demonstrated each violinist to have developed an individualized pacing for shifts, a feature that should influence timing effects and prove foundational to aesthetic outcomes during performance. Such results underpin the potential for scientific methodologies to unravel mysteries of performance that are associated with a performer's personal artistic style. PMID:26557431

  12. Unraveling mysteries of personal performance style; biomechanics of left-hand position changes (shifting) in violin performance.

    PubMed

    Visentin, Peter; Li, Shiming; Tardif, Guillaume; Shan, Gongbing

    2015-01-01

    Instrumental music performance ranks among the most complex of learned human behaviors, requiring development of highly nuanced powers of sensory and neural discrimination, intricate motor skills, and adaptive abilities in a temporal activity. Teaching, learning and performing on the violin generally occur within musico-cultural parameters most often transmitted through aural traditions that include both verbal instruction and performance modeling. In most parts of the world, violin is taught in a manner virtually indistinguishable from that used 200 years ago. The current study uses methods from movement science to examine the "how" and "what" of left-hand position changes (shifting), a movement skill essential during violin performance. In doing so, it begins a discussion of artistic individualization in terms of anthropometry, the performer-instrument interface, and the strategic use of motor behaviors. Results based on 540 shifting samples, a case series of 6 professional-level violinists, showed that some elements of the skill were individualized in surprising ways while others were explainable by anthropometry, ergonomics and entrainment. Remarkably, results demonstrated each violinist to have developed an individualized pacing for shifts, a feature that should influence timing effects and prove foundational to aesthetic outcomes during performance. Such results underpin the potential for scientific methodologies to unravel mysteries of performance that are associated with a performer's personal artistic style.

  13. Unraveling mysteries of personal performance style; biomechanics of left-hand position changes (shifting) in violin performance

    PubMed Central

    Visentin, Peter; Li, Shiming; Tardif, Guillaume

    2015-01-01

    Instrumental music performance ranks among the most complex of learned human behaviors, requiring development of highly nuanced powers of sensory and neural discrimination, intricate motor skills, and adaptive abilities in a temporal activity. Teaching, learning and performing on the violin generally occur within musico-cultural parameters most often transmitted through aural traditions that include both verbal instruction and performance modeling. In most parts of the world, violin is taught in a manner virtually indistinguishable from that used 200 years ago. The current study uses methods from movement science to examine the “how” and “what” of left-hand position changes (shifting), a movement skill essential during violin performance. In doing so, it begins a discussion of artistic individualization in terms of anthropometry, the performer-instrument interface, and the strategic use of motor behaviors. Results based on 540 shifting samples, a case series of 6 professional-level violinists, showed that some elements of the skill were individualized in surprising ways while others were explainable by anthropometry, ergonomics and entrainment. Remarkably, results demonstrated each violinist to have developed an individualized pacing for shifts, a feature that should influence timing effects and prove foundational to aesthetic outcomes during performance. Such results underpin the potential for scientific methodologies to unravel mysteries of performance that are associated with a performer’s personal artistic style. PMID:26557431

  14. Time-frequency optimization for discrimination between imagination of right and left hand movements based on two bipolar electroencephalography channels

    NASA Astrophysics Data System (ADS)

    Yang, Yuan; Chevallier, Sylvain; Wiart, Joe; Bloch, Isabelle

    2014-12-01

    To enforce a widespread use of efficient and easy to use brain-computer interfaces (BCIs), the inter-subject robustness should be increased and the number of electrodes should be reduced. These two key issues are addressed in this contribution, proposing a novel method to identify subject-specific time-frequency characteristics with a minimal number of electrodes. In this method, two alternative criteria, time-frequency discrimination factor ( TFDF) and F score, are proposed to evaluate the discriminative power of time-frequency regions. Distinct from classical measures (e.g., Fisher criterion, r 2 coefficient), the TFDF is based on the neurophysiologic phenomena, on which the motor imagery BCI paradigm relies, rather than only from statistics. F score is based on the popular Fisher's discriminant and purely data driven; however, it differs from traditional measures since it provides a simple and effective measure for quantifying the discriminative power of a multi-dimensional feature vector. The proposed method is tested on BCI competition IV datasets IIa and IIb for discriminating right and left hand motor imagery. Compared to state-of-the-art methods, our method based on both criteria led to comparable or even better classification results, while using fewer electrodes (i.e., only two bipolar channels, C3 and C4). This work indicates that time-frequency optimization can not only improve the classification performance but also contribute to reducing the number of electrodes required in motor imagery BCIs.

  15. Transverse acceleration of oxygen ions by electromagnetic ion cyclotron resonance with broad band left-hand polarized waves

    NASA Technical Reports Server (NTRS)

    Chang, T.; Crew, G. B.; Hershkowitz, N.; Jasperse, J. R.; Retterer, J. M.

    1986-01-01

    Central plasma sheet (CPS) ion conics are oxygen-dominated, with peak energies ranging from tens to hundreds of eV centered around pitch-angles between 115 and 130 degrees. Because of the lack of correlation between the CPS conics and the observed currents and/or electron beam-like structures, it is not likely that all of these conics are generated by interactions with electrostatic ion cyclotron waves or lower hybrid waves. Instead, it is suggested that the observed intense broad band electric field fluctuations in the frequency range between 0 and 100 Hz can be responsible for the transverse energization of the ions through cyclotron resonance heating with the left-hand polarized electromagnetic waves. This process is much more efficient for heating the oxygen ions than hydrogen ions, thus providing a plausible explanation of the oxygen dominance in CPS conics. Simple algebraic expressions are given from which estimates of conic energy and pitch angle can be easily calculated. This suggested mechanism can also provide some preheating of the oxygen ions in the boundary plasma sheet (BPS) where discrete aurorae form.

  16. Conformation and sequence evidence for two-fold symmetry in left-handed beta-helix fold.

    PubMed

    Shen, Xiaojuan

    2011-09-21

    The left-handed beta-helix (LβH) has received interest recently as it folds as a possible solution for the structure of misfolded proteins associated with prion and Huntington's diseases. Through a combination of sequence and structure analysis, we uncover a novel feature that is common to this unique fold: a two-fold symmetry in both sequence and structure, and this feature always coupled with extended loops in the middle of the helix. Since the results reveal a two-fold symmetric pattern both in the sequence and structure, it may indicate that the symmetry in tertiary structure is coded by the symmetry in primary sequence, which agrees with Anfisen's proposal that a protein's amino-acid sequence specify its three-dimensional structure. It may also indicate that LβH adopts a two-fold repeat pattern during the evolution process and symmetry helps maintaining the stability of the helix structure. The two-fold symmetric pattern and extended loops might be important in maintaining stability of helix proteins. This discovery can be useful in understanding the folding mechanisms of this protein fold and provide insights in the relation between sequences and structures.

  17. Choice of transmission line for operation in the millimeter-wave range

    NASA Astrophysics Data System (ADS)

    Kazantsev, V. I.; Kharitonov, A. I.

    1989-10-01

    The paper presents requirements for millimeter-wave transmission lines, including low losses, high electrical strength, wide operating band, weak dispersion, good manufacturability, electrohermeticity, low weight and small size, and low cost. Lines that fully satisfy these requirements are described.

  18. 78 FR 44586 - Draft Environmental Assessment and Proposed Cross Valley Transmission Line Habitat Conservation...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-24

    ... Habitat Conservation Plan, Tulare County, California AGENCY: Fish and Wildlife Service, Interior. ACTION: Notice of availability; receipt of permit application, draft environmental assessment, proposed habitat... prepared the draft Cross Valley Transmission Line Habitat Conservation Plan (Cross Valley Line HCP)...

  19. ``Multifractals in Transmission of Off-line & On-line E-Voting Systems''

    NASA Astrophysics Data System (ADS)

    Maksoed, Wh-

    An e-voting systems is a voting system in which the election data is recorded, stored & processed primarily as digital information. Those are 2 type of e-voting systems: off-line & on-line systems[Alaguvel & Gnanavel, 2013]. ``Using transfer matrix method & multifractal theory, we studied the transmission properties of 1D generalized Fibonacci structures GF(m.n) in which m & n different intervals are integer according to a substitution rule[Yuannong Zhang, et.al,:Multifractal properties of 1D quasi-period Photonic Crystal''. ``Transmission spectra of 1D fractal multilayer structures are found to exhibit self-similar properties'' says Zhukovsky & Lavrinenko in ``Spectral self-similarity in fractal 1D photonic structures'',Photonics & Nanostructures, 2005 whereas Jacob Trevino, et.al studies `structural properties, photonic density of state & bandedge modes of Vogel spiral arrays of dielectric cylinders in air'. Acknowledgment to HE. Mr. AUGUST PARENGKUAN if accepts 1995-2005 Invoicing & Fulfillments to ``KOMPAS'' cq the Prodi of Physics ITB.

  20. Negotiating left-hand and right-hand bends: a motorcycle simulator study to investigate experiential and behaviour differences across rider groups.

    PubMed

    Crundall, Elizabeth; Crundall, David; Stedmon, Alex W

    2012-01-01

    Why do motorcyclists crash on bends? To address this question we examined the riding styles of three groups of motorcyclists on a motorcycle simulator. Novice, experienced and advanced motorcyclists navigated a series of combined left and right bends while their speed and lane position were recorded. Each rider encountered an unexpected hazard on both a left- and right-hand bend section. Upon seeing the hazards, all riders decreased their speed before steering to avoid the hazard. Experienced riders tended to follow more of a racing line through the bends, which resulted in them having to make the most severe changes to their position to avoid a collision. Advanced riders adopted the safest road positions, choosing a position which offered greater visibility through the bends. As a result, they did not need to alter their road position in response to the hazard. Novice riders adopted similar road positions to experienced riders on the left-hand bends, but their road positions were more similar to advanced riders on right-hand bends, suggesting that they were more aware of the risks associated with right bends. Novice riders also adopted a safer position on post-hazard bends whilst the experienced riders failed to alter their behaviour even though they had performed the greatest evasive manoeuvre in response to the hazards. Advanced riders did not need to alter their position as their approach to the bends was already optimal. The results suggest that non-advanced riders were more likely to choose an inappropriate lane position than an inappropriate speed when entering a bend. Furthermore, the findings support the theory that expertise is achieved as a result of relearning, with advanced training overriding 'bad habits' gained through experience alone.

  1. Novel Micromachined Coplanar Waveguide Transmission Lines for Application in Millimeter-Wave Circuits

    NASA Astrophysics Data System (ADS)

    Park, Jae-Hyoung; Baek, Chang-Wook; Jung, Sanghwa; Kim, Hong-Teuk; Kwon, Youngwoo; Kim, Yong-Kweon

    2000-12-01

    In this paper, novel micromachined coplanar waveguide(CPW) transmission lines for application in millimeter-wave circuits are proposed. Two types of transmission lines with the length of 1 cm are fabricated and the measured characteristics are compared with those of the conventional CPW transmission line. One is the elevated CPW(ECPW) transmission line and the other is the overlay CPW(OCPW) line. These transmission lines are composed of 3-μm-thick electroplated gold lines with overhanging parts. By elevating the metal lines from the substrate using micromachining technology, the conductor and substrate dielectric loss can be reduced and easily integrated with conventional monolithic microwave integrated circuits. Compared with the conventional CPW line showing 2.65 dB/cm insertion loss at 50 GHz, the loss can be reduced to 1.9 dB/cm and 1.25 dB/cm at 50 GHz in the case of the ECPW and OCPW transmission lines, respectively. Also, the OCPW transmission line shows that the insertion loss does not vary with the change of the characteristic impedance. As shown in the measured and simulated results, the insertion loss is maintained below 1.4 dB/cm over wide impedance ranges.

  2. Analysis of the Transient Response of a Dual-Fed RC Transmission Line

    PubMed Central

    Dorraki, Mohsen; Cambrell, Gregory K.; Abbott, Derek

    2015-01-01

    The transient analysis of a uniform transmission line of finite length is considered in this paper. For the first time this paper provides an analytical expression for the time-domain response of an RC transmission line, which is stimulated by a step function that is fed into both ends of the transmission line. In particular, we find an analytical expression for the step response at the center of the transmission line, in order to determine the worst-case rise time. This is of interest, for example, in large charge-coupled device (CCD) arrays, where long polysilicon lines are dual-fed in order to mitigate degradation in rise time. The analytical expressions for the RC transmission line are supported by computer-simulated lumped RC models. PMID:25679379

  3. Right-handed and left-handed G-quadruplexes have the same DNA sequence: distinct conformations induced by an organic small molecule and potassium.

    PubMed

    Fu, Boshi; Huang, Jinguo; Chen, Yuqi; Wang, Yafen; Xue, Tianrui; Xu, GuoHua; Wang, Shaoru; Zhou, Xiang

    2016-08-21

    Herein, we report two distinct G-quadruplex conformations of the same G-rich oligonucleotide, regulated by a small molecule. This is the first report in which both right- and left-handed G-quadruplex conformations have been obtained from the same sequence. We discriminated these two distinct conformations and investigated their kinetics and thermodynamics.

  4. The formation of right-handed and left-handed chiral nanopores within a single domain during amino acid self-assembly on Au(111).

    PubMed

    Yang, Sena; Jeon, Aram; Driver, Russell W; Kim, Yeonwoo; Jeon, Eun Hee; Kim, Sehun; Lee, Hee-Seung; Lee, Hangil

    2016-05-25

    We report the formation of both right- and left-handed chiral nanopores within a single domain during the self-assembly of an amino acid derivative on an inert Au(111) surface using STM. DFT calculations employed to rationalize this unusual result identified that intermolecular interactions between chiral, windmill-shaped tetramers are crucial for self-assembly.

  5. Electric Utility Transmission and Distribution Line Engineering Program

    SciTech Connect

    Peter McKenny

    2010-08-31

    Economic development in the United States depends on a reliable and affordable power supply. The nation will need well educated engineers to design a modern, safe, secure, and reliable power grid for our future needs. An anticipated shortage of qualified engineers has caused considerable concern in many professional circles, and various steps are being taken nationwide to alleviate the potential shortage and ensure the North American power system's reliability, and our world-wide economic competitiveness. To help provide a well-educated and trained workforce which can sustain and modernize the nation's power grid, Gonzaga University's School of Engineering and Applied Science has established a five-course (15-credit hour) Certificate Program in Transmission and Distribution (T&D) Engineering. The program has been specifically designed to provide working utility engineering professionals with on-line access to advanced engineering courses which cover modern design practice with an industry-focused theoretical foundation. A total of twelve courses have been developed to-date and students may select any five in their area of interest for the T&D Certificate. As each course is developed and taught by a team of experienced engineers (from public and private utilities, consultants, and industry suppliers), students are provided a unique opportunity to interact directly with different industry experts over the eight weeks of each course. Course material incorporates advanced aspects of civil, electrical, and mechanical engineering disciplines that apply to power system design and are appropriate for graduate engineers. As such, target students for the certificate program include: (1) recent graduates with a Bachelor of Science Degree in an engineering field (civil, mechanical, electrical, etc.); (2) senior engineers moving from other fields to the utility industry (i.e. paper industry to utility engineering or project management positions); and (3) regular working

  6. Recent progress of the improved magnetically insulated transmission line oscillator.

    PubMed

    Fan, Yu-Wei; Zhong, Hui-Huang; Li, Zhi-Qiang; Shu, Ting; Zhang, Jian-De; Liu, Jin-Liang; Yang, Jian-Hua; Zhang, Jun; Yuan, Cheng-Wei; Luo, Ling

    2008-03-01

    The improved magnetically insulated transmission line oscillator (MILO) is a gigawatt-class L-band high power microwave tube driven by a 550 kV, 57 kA, 50 ns electron beam. It has allowed us to generate 2.4 GW pulse of 22 ns duration. The recent progress of the improved MILO is presented in this paper. First, a field shaper cathode is introduced into the improved MILO to avoid the cathode flares in the triple point region. The experimental results show that the cathode flares are avoided, so the lifetime of the velvet cathode is longer than that of the taper cathode. Furthermore, the shot-to-shot reproducibility is better than that of the taper cathode. Second, In order to prolong the pulse duration and increase the radiated microwave power, a self-built 600 kV, 10 Omega, 80 ns pulser: SPARK-03 is employed to drive the improved MILO. Simulation and experimental investigation are performed. In simulation, when the improved MILO is driven by a 600 kV, 57 kA electron beam, high-power microwave is generated with output power of 4.15 GW, frequency of 1.76 GHz, and relevant power conversion efficiency of 12.0%. In experiments, when the diode voltage is 550 kV and current is 54 kA, the measured results are that the radiated microwave power is above 3.1 GW, the pulse duration is above 40 ns, the microwave frequency is about 1.755 GHz, and the power conversion efficiency is about 10.4%.

  7. Motor unit activity in biceps brachii of left-handed humans during sustained contractions with two load types.

    PubMed

    Gould, Jeffrey R; Cleland, Brice T; Mani, Diba; Amiridis, Ioannis G; Enoka, Roger M

    2016-09-01

    The purpose of the study was to compare the discharge characteristics of single motor units during sustained isometric contractions that required either force or position control in left-handed individuals. The target force for the two sustained contractions (24.9 ± 10.5% maximal force) was identical for each biceps brachii motor unit (n = 32) and set at 4.7 ± 2.0% of maximal voluntary contraction (MVC) force above its recruitment threshold (range: 0.5-41.2% MVC force). The contractions were not sustained to task failure, but the duration (range: 60-330 s) was identical for each motor unit and the decline in MVC force immediately after the sustained contractions was similar for the two tasks (force: 11.1% ± 13.7%; position: 11.6% ± 9.9%). Despite a greater increase in the rating of perceived exertion during the position task (task × time interaction, P < 0.006), the amplitude of the surface-recorded electromyogram for the agonist and antagonist muscles increased similarly during the two tasks. Nonetheless, mean discharge rate of the biceps brachii motor units declined more during the position task (task × time interaction, P < 0.01) and the variability in discharge times (coefficient of variation for interspike interval) increased only during the position task (task × time interaction, P < 0.008). When combined with the results of an identical study on right-handers (Mottram CJ, Jakobi JM, Semmler JG, Enoka RM. J Neurophysiol 93: 1381-1392, 2005), the findings indicate that handedness does not influence the adjustments in biceps brachii motor unit activity during sustained submaximal contractions requiring either force or position control.

  8. Right- and Left-Handed Helices, What is in between? Interconversion of Helical Structures of Alternating Pyridinedicarboxamide/m-(phenylazo)azobenzene Oligomers.

    PubMed

    Tao, Peng; Parquette, Jon R; Hadad, Christopher M

    2012-12-11

    Some unnatural polymers/oligomers have been designed to adopt a well-defined, compact, three-dimensional folding capability. Azobenzene units are common linkages in these oligomer designs. Two alternating pyridinedicarboxamide/m-(phenylazo)azobenzene oligomers that can fold into both right- and left-handed helices were studied computationally in order to understand their dynamical properties. Helical structures were shown to be the global minima among the many different conformations generated from the Monte Carlo simulations, and extended conformations have higher potential energies than compact ones. To understand the interconversion process between right- and left-handed helices, replica-exchange molecular dynamic (REMD) simulations were performed on both oligomers, and with this method, both right- and left-handed helices were successfully sampled during the simulations. REMD trajectories revealed twisted conformations as intermediate structures in the interconversion pathway between the two helical forms of these azobenzene oligomers. This mechanism was observed in both oligomers in current study and occurred locally in the larger oligomer. This discovery indicates that the interconversion between helical structures with different handedness goes through a compact and partially folded structure instead of globally unfold and extended structure. This is also verified by the nudged elastic band (NEB) calculations. The temperature weighted histogram analysis method (T-WHAM) was applied on the REMD results to generate contour maps of the potential of mean force (PMF). Analysis showed that right- and left-handed helices are equally sampled in these REMD simulations. In large oligomers, both right- and left-handed helices can be adopted by different parts of the molecule simultaneously. The interconversion between two helical forms can occur in the middle of the helical structure and not necessarily at the termini of the oligomer.

  9. 76 FR 21338 - Reopening of Scoping Period for the Northern Pass Transmission Line Project Environmental Impact...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-15

    ... Reopening of Scoping Period for the Northern Pass Transmission Line Project Environmental Impact Statement... (DOE) is reopening the public scoping period for the Northern Pass Transmission Line Project Environmental Impact Statement (EIS) (DOE/EIS-0463). The scoping period now ends on June 14, 2011. DOE...

  10. 76 FR 34969 - Extension of Scoping Period for the Northern Pass Transmission Line Project Environmental Impact...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-15

    ... Extension of Scoping Period for the Northern Pass Transmission Line Project Environmental Impact Statement... Register (76 FR 7828) its intention to prepare an EIS to assess the potential environmental impacts from... (DOE) is reopening the public scoping period for the Northern Pass Transmission Line...

  11. 78 FR 57372 - Northern Pass Transmission Line Project Environmental Impact Statement: Announcement of Change in...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-18

    ... Northern Pass Transmission Line Project Environmental Impact Statement: Announcement of Change in Public... amended Notice of Intent (NOI) to modify the scope of the Northern Pass Transmission Line Project Environmental Impact Statement (EIS) (DOE/EIS-0463) and to conduct additional public scoping meetings (78...

  12. A calibration technique for measuring the complex permittivity of materials with planar transmission lines

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A simple two-standard calibration procedure for determining the permittivity of a material from the propagation constant measured with planar transmission lines is presented. The suitability of this procedure is demonstrated by using a coplanar waveguide transmission-line sensor to measure the permi...

  13. View facing east (70°) of Transmission Line crossing Marias River, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View facing east (70°) of Transmission Line crossing Marias River, near Structure 47-9, grain elevators in town of Loma visible in background - Havre Rainbow Transmission Line, Havre City to Great Falls vicinity, Montana, Great Falls, Cascade County, MT

  14. Context view of RyantoRainbow 100kv Transmission Line showing copper wire ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Context view of Ryan-to-Rainbow 100kv Transmission Line showing copper wire conductors leaving roof of Ryan Powerhouse. View to east - Ryan Hydroelectric Facility, Ryan-to-Rainbow 100 kV Transmission Line, West bank of Missouri River, northeast of Great Falls, Great Falls, Cascade County, MT

  15. 49 CFR 192.717 - Transmission lines: Permanent field repair of leaks.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... leaks. 192.717 Section 192.717 Transportation Other Regulations Relating to Transportation (Continued... § 192.717 Transmission lines: Permanent field repair of leaks. Each permanent field repair of a leak on a transmission line must be made by— (a) Removing the leak by cutting out and replacing...

  16. 49 CFR 192.717 - Transmission lines: Permanent field repair of leaks.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... leaks. 192.717 Section 192.717 Transportation Other Regulations Relating to Transportation (Continued... § 192.717 Transmission lines: Permanent field repair of leaks. Each permanent field repair of a leak on a transmission line must be made by— (a) Removing the leak by cutting out and replacing...

  17. 49 CFR 192.717 - Transmission lines: Permanent field repair of leaks.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... leaks. 192.717 Section 192.717 Transportation Other Regulations Relating to Transportation (Continued... § 192.717 Transmission lines: Permanent field repair of leaks. Each permanent field repair of a leak on a transmission line must be made by— (a) Removing the leak by cutting out and replacing...

  18. Some Little-Known Facts about Transmission Lines and Some New Results

    ERIC Educational Resources Information Center

    Dutta Roy, Suhash C.

    2010-01-01

    The study of transmission lines forms an integral part of any curriculum in electrical engineering. This paper presents some little-known but interesting facts about transmission lines, which are generally not found in textbooks, along with some new facts, which arose as extensions of these little-known ones. The facts highlighted in this paper…

  19. Explanation of the inverse Doppler effect observed in nonlinear transmission lines.

    PubMed

    Kozyrev, Alexander B; van der Weide, Daniel W

    2005-05-27

    The theory of the inverse Doppler effect recently observed in magnetic nonlinear transmission lines is developed. We explain the crucial role of the backward spatial harmonic in the occurrence of an inverse Doppler effect and draw analogies of the magnetic nonlinear transmission line to the backward wave oscillator.

  20. 49 CFR 192.715 - Transmission lines: Permanent field repair of welds.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Transmission lines: Permanent field repair of welds. 192.715 Section 192.715 Transportation Other Regulations Relating to Transportation (Continued... § 192.715 Transmission lines: Permanent field repair of welds. Each weld that is unacceptable...

  1. 75 FR 56051 - Bemidji to Grand Rapids Minnesota 230 kV Transmission Line Project

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-09-15

    ...; ] DEPARTMENT OF AGRICULTURE Rural Utilities Service Bemidji to Grand Rapids Minnesota 230 kV Transmission Line... Rapids, Minnesota 230 kV Transmission Line Project (``Project'') in Minnesota. The Final EIS was prepared... application of Minnkota Power Cooperative, Inc. for RUS financing to construct a 230 kilovolt...

  2. Millimeter-Gap Magnetically Insulated Transmission Line Power Flow Experiments

    SciTech Connect

    Hutsel, Brian Thomas; Stoltzfus, Brian S.; Fowler, William E.; LeChien, Keith R.; Mazarakis, Michael G.; Moore, James K.; Mulville, Thomas D.; Savage, Mark E.; Stygar, William A.; McKenney, John L.; Jones, Peter A.; MacRunnels, Diego J.; Long, Finis W.; Porter, John L.

    2014-09-01

    An experiment platform has been designed to study vacuum power flow in magnetically insulated transmission lines (MITLs). The platform was driven by the 400-GW Mykonos-V accelerator. The experiments conducted quantify the current loss in a millimeter-gap MITL with respect to vacuum conditions in the MITL for two different gap distances, 1.0 and 1.3 mm. The current loss for each gap was measured for three different vacuum pump down times. As a ride along experiment, multiple shots were conducted with each set of hardware to determine if there was a conditioning effect to increase current delivery on subsequent shots. The experiment results revealed large differences in performance for the 1.0 and 1.3 mm gaps. The 1.0 mm gap resulted in current loss of 40%-60% of peak current. The 1.3 mm gap resulted in current losses of less than 5% of peak current. Classical MITL models that neglect plasma expansion predict that there should be zero current loss, after magnetic insulation is established, for both of these gaps. The experiments result s indicate that the vacuum pressure or pump down time did not have a significant effect on the measured current loss at vacuum pressures between 1e-4 and 1e-5 Torr. Additionally, there was not repeatable evidence of a conditioning effect that reduced current loss for subsequent full-energy shots on a given set of hardware. It should be noted that the experiments conducted likely did not have large loss contributions due to ion emission from the anode due to the relatively small current densi-ties (25-40 kA/cm) in the MITL that limited the anode temperature rise due to ohmic heating. The results and conclusions from these experiments may have limited applicability to MITLs of high current density (>400 kA/cm) used in the convolute and load region of the Z which experience temperature increases of >400° C and generate ion emission from anode surfaces.

  3. Computation of transient electromagnetic fields radiated by transmission line: An exact model

    SciTech Connect

    Shi, R.S.; Darcherif, A.; Sabonnadiere, J.C.

    1995-07-01

    A novel time domain analytical method for predicting electromagnetic field transients resulting from power line switching operations is presented in this paper. This method, which is directly derived from electromagnetic field theory of a power transmission line, allows the field transients to be accurately and efficiently calculated. It will be shown that conventional numerical methods for computing transmission line transient electromagnetic fields are in fact degenerative approximate models for this analytical method.

  4. Transmission characteristics and transmission line model of a metal-insulator-metal waveguide with a stub modified by cuts.

    PubMed

    Shen, Xinru; Wang, Yueke; Yan, Xin; Yuan, Lin; Sang, Tian

    2016-08-10

    We propose a structure of a metal-insulator-metal (MIM) waveguide with a stub modified by cuts. Our simulation results, conducted by the finite element method, show that the wavelengths of transmission dip vary with the position of the cuts and form the zigzag lines. A transmission line model is also presented, and it agrees with simulation results well. It is believed that our findings provide a smart way to design a plasmonic waveguide filter at the communication region based on MIM structures. PMID:27534492

  5. Sensor, method and system of monitoring transmission lines

    SciTech Connect

    Syracuse, Steven J.; Clark, Roy; Halverson, Peter G.; Tesche, Frederick M.; Barlow, Charles V.

    2012-10-02

    An apparatus, method, and system for measuring the magnetic field produced by phase conductors in multi-phase power lines. The magnetic field measurements are used to determine the current load on the conductors. The magnetic fields are sensed by coils placed sufficiently proximate the lines to measure the voltage induced in the coils by the field without touching the lines. The x and y components of the magnetic fields are used to calculate the conductor sag, and then the sag data, along with the field strength data, can be used to calculate the current load on the line and the phase of the current. The sag calculations of this invention are independent of line voltage and line current measurements. The system applies a computerized fitter routine to measured and sampled voltages on the coils to accurately determine the values of parameters associated with the overhead phase conductors.

  6. The Effect Analysis of Strain Rate on Power Transmission Tower-Line System under Seismic Excitation

    PubMed Central

    Wang, Wenming

    2014-01-01

    The effect analysis of strain rate on power transmission tower-line system under seismic excitation is studied in this paper. A three-dimensional finite element model of a transmission tower-line system is created based on a real project. Using theoretical analysis and numerical simulation, incremental dynamic analysis of the power transmission tower-line system is conducted to investigate the effect of strain rate on the nonlinear responses of the transmission tower and line. The results show that the effect of strain rate on the transmission tower generally decreases the maximum top displacements, but it would increase the maximum base shear forces, and thus it is necessary to consider the effect of strain rate on the seismic analysis of the transmission tower. The effect of strain rate could be ignored for the seismic analysis of the conductors and ground lines, but the responses of the ground lines considering strain rate effect are larger than those of the conductors. The results could provide a reference for the seismic design of the transmission tower-line system. PMID:25105157

  7. The effect analysis of strain rate on power transmission tower-line system under seismic excitation.

    PubMed

    Tian, Li; Wang, Wenming; Qian, Hui

    2014-01-01

    The effect analysis of strain rate on power transmission tower-line system under seismic excitation is studied in this paper. A three-dimensional finite element model of a transmission tower-line system is created based on a real project. Using theoretical analysis and numerical simulation, incremental dynamic analysis of the power transmission tower-line system is conducted to investigate the effect of strain rate on the nonlinear responses of the transmission tower and line. The results show that the effect of strain rate on the transmission tower generally decreases the maximum top displacements, but it would increase the maximum base shear forces, and thus it is necessary to consider the effect of strain rate on the seismic analysis of the transmission tower. The effect of strain rate could be ignored for the seismic analysis of the conductors and ground lines, but the responses of the ground lines considering strain rate effect are larger than those of the conductors. The results could provide a reference for the seismic design of the transmission tower-line system. PMID:25105157

  8. The effect analysis of strain rate on power transmission tower-line system under seismic excitation.

    PubMed

    Tian, Li; Wang, Wenming; Qian, Hui

    2014-01-01

    The effect analysis of strain rate on power transmission tower-line system under seismic excitation is studied in this paper. A three-dimensional finite element model of a transmission tower-line system is created based on a real project. Using theoretical analysis and numerical simulation, incremental dynamic analysis of the power transmission tower-line system is conducted to investigate the effect of strain rate on the nonlinear responses of the transmission tower and line. The results show that the effect of strain rate on the transmission tower generally decreases the maximum top displacements, but it would increase the maximum base shear forces, and thus it is necessary to consider the effect of strain rate on the seismic analysis of the transmission tower. The effect of strain rate could be ignored for the seismic analysis of the conductors and ground lines, but the responses of the ground lines considering strain rate effect are larger than those of the conductors. The results could provide a reference for the seismic design of the transmission tower-line system.

  9. A planar transmission-line sensor for measuring microwave permittivity of liquid and semisolid biological materials

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An accurate technique for determining the permittivity of biological materials with coplanar waveguide transmission line is presented. The technique utilizes closed-form approximations that relate the material permittivity to the line propagation constant. A thru-reflect-line calibration procedure i...

  10. Research on UAV Intelligent Obstacle Avoidance Technology During Inspection of Transmission Line

    NASA Astrophysics Data System (ADS)

    Wei, Chuanhu; Zhang, Fei; Yin, Chaoyuan; Liu, Yue; Liu, Liang; Li, Zongyu; Wang, Wanguo

    Autonomous obstacle avoidance of unmanned aerial vehicle (hereinafter referred to as UAV) in electric power line inspection process has important significance for operation safety and economy for UAV intelligent inspection system of transmission line as main content of UAV intelligent inspection system on transmission line. In the paper, principles of UAV inspection obstacle avoidance technology of transmission line are introduced. UAV inspection obstacle avoidance technology based on particle swarm global optimization algorithm is proposed after common obstacle avoidance technologies are studied. Stimulation comparison is implemented with traditional UAV inspection obstacle avoidance technology which adopts artificial potential field method. Results show that UAV inspection strategy of particle swarm optimization algorithm, adopted in the paper, is prominently better than UAV inspection strategy of artificial potential field method in the aspects of obstacle avoidance effect and the ability of returning to preset inspection track after passing through the obstacle. An effective method is provided for UAV inspection obstacle avoidance of transmission line.

  11. Hemispheric prevalence during chewing in normal right-handed and left-handed subjects: a functional magnetic resonance imaging preliminary study.

    PubMed

    Bracco, Pietro; Anastasi, Giuseppe; Piancino, Maria Grazia; Frongia, Gianluigi; Milardi, Demetrio; Favaloro, Angelo; Bramanti, Placido

    2010-04-01

    This study evaluated the activation of different cortical areas during nondeliberate chewing of soft and hard boluses in five right-handed and five left-handed subjects with normal occlusion, to determine different hemispheric prevalences. The study was conducted with a functional Magnetic Resonance Imaging (1.5 T Magnetom Vision - Siemens Medical, Germany) using a head coil. The results showed that the most frequently activated areas were Brodmann's areas four and six in the primary motor and premotor cortex, the insula and Broca's area and, overall, showed greater activity of the cortical mastication area (CMA) in the right hemisphere for right-handed and in the left hemisphere for left-handed subjects.

  12. Recognition and one-pot extraction of right- and left-handed semiconducting single-walled carbon nanotube enantiomers using fluorene-binaphthol chiral copolymers.

    PubMed

    Akazaki, Kojiro; Toshimitsu, Fumiyuki; Ozawa, Hiroaki; Fujigaya, Tsuyohiko; Nakashima, Naotoshi

    2012-08-01

    Synthesized single-walled carbon nanotubes (SWNTs) are mixtures of right- and left-handed helicity and their separation is an essential topic in nanocarbon science. In this paper, we describe the separation of right- and left-handed semiconducting SWNTs from as-produced SWNTs. Our strategy for this goal is simple: we designed copolymers composed of polyfluorene and chiral bulky moieties because polyfluorenes with long alkyl-chains are known to dissolve only semiconducting SWNTs and chiral binaphthol is a so-called BINAP family that possesses a powerful enantiomer sorting capability. In this study, we synthesized 12 copolymers, (9,9-dioctylfluorene-2,7-diyl)x((R)- or (S)-2,2'-dimethoxy-1,1'-binaphthalen-6,6-diyl)y, where x and y are copolymer composition ratios. It was found that, by a simple one-pot sonication method, the copolymers are able to extract either right- or left-handed semiconducting SWNT enantiomers with (6,5)- and (7,5)-enriched chirality. The separated materials were confirmed by circular dichroism, vis-near IR and photoluminescence spectroscopies. Interestingly, the copolymer showed inversion of SWNT enantiomer recognition at higher contents of the chiral binaphthol moiety. Molecular mechanics simulations reveal a cooperative effect between the degree of chirality and copolymer conformation to be responsible for these distinct characteristics of the extractions. This is the first example describing the rational design and synthesis of novel compounds for the recognition and simple sorting of right- and left-handed semiconducting SWNTs with a specific chirality.

  13. The biomechanics of situational baseball: execution and perception of left-handed pitchers' simulated pick-off moves to first base.

    PubMed

    Fortenbaugh, Dave; Butcher-Mokha, Monique

    2007-01-01

    The aim of this study was to provide an in-depth analysis of the pick-off play in baseball. Ten collegiate left-handed pitchers and nine base-runners participated in this study. The pitchers were videotaped with four cameras to derive three-dimensional data while performing deliveries in the directions of first base and home plate in a laboratory setting. Deliveries were performed from flat ground. Differences between these deliveries were measured through ten selected joint and segment angles. The base-runners completed two distinct procedures in which they viewed video footage of left-handed pitchers and estimated the intended delivery direction. Base-runners were subsequently interviewed to determine the reasoning behind their decisions. The pitchers' data revealed differences between delivery types in nearly all of the selected angles (P < 0.01). The base-runners' data demonstrated that their ability to discriminate delivery types improved when allowed more viewing time per trial (P < 0.01). Additionally, commonalities exist among the base-runners' focal points on the pitcher while making decisions regarding delivery direction and the kinematic differences between deliveries in left-handed pitchers. The practical significance of these results, however, may be more difficult to interpret.

  14. A planar transmission-line sensor for measuring the microwave permittivity of liquid and semisolid biological materials

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A planar transmission-line configuration for rapid, nondestructive, wideband permittivity measurements of liquid and semisolid materials at microwave frequencies is described. The transmission-line propagation constant of the proposed configuration is determined with the multiline technique from sca...

  15. Hayden-Blue River 345-kV transmission line project, Colorado

    SciTech Connect

    Not Available

    1982-09-01

    Tri-State Generation and Transmission Association, Inc., Colorado-Ute Electric Association, Inc., Platte River Power Authority, and Western Area Power Administration propose to construct and operate approximately 90 miles of 345-kilovolt (kV) transmission line between Hayden and the Blue River Valley in Colorado. The project would involve expansion of existing substation facilities at Hayden and construction of two new substations. The line would be operated at 230 kV initially. Estimated cost of the project is $37.8 million. The new line and substation facilities would provide a backup transmission path, satisfy the long-term needs in meeting the energy requirements, improve system reliability, improve system stability for the Craig and Hayden generating stations, and leave the existing 115-kV and 138-kV lines in operation to provide additional transmission capacity that would function as backup transmission during an outage on another line. Minute amounts of lands would be displaced. Construction activities would disturb critical ranges for elk and mule deer, elk calving areas, and the mating and nesting areas of greater sandhill cranes, great blue herons, sage grouse, golden eagles, and prairie falcons. Management of timberland would damage natural vegetation. The line would traverse 3.1 miles of flood-prone area, and as many as three transmission towers would lie within the floodplain of the Colorado River. The visual quality of land crossed by the line would be degraded somewhat.

  16. Electric power high-voltage transmission lines: Design options, cost, and electric and magnetic field levels

    SciTech Connect

    Stoffel, J.B.; Pentecost, E.D.; Roman, R.D.; Traczyk, P.A.

    1994-11-01

    This report provides background information about (1) the electric and magnetic fields (EMFs) of high-voltage transmission lines at typical voltages and line configurations and (2) typical transmission line costs to assist on alternatives in environmental documents. EMF strengths at 0 {+-} 200 ft from centerline were calculated for ac overhead lines, and for 345 and 230-kV ac underground line and for a {+-}450-kV dc overhead line. Compacting and height sensitivity factors were computed for the variation in EMFs when line conductors are moved closer or raised. Estimated costs for the lines are presented and discussed so that the impact of using alternative strategies for reducing EMF strengths and the implications of implementing the strategies can be better appreciated.

  17. Coyote Pumping Plant 115-kV transmission line project, Santa Clara County, California: Environmental assessment

    SciTech Connect

    Not Available

    1985-01-01

    Environmental impacts expected from the design and siting of transmission lines and the associated pumping plant station are addressed with alternative routes and actions considered, in compliance with environmental laws. (PSB)

  18. PennsylvaniaNew Jersey Interconnection Bushkill to Roseland Transmission Line, From Roseland ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Pennsylvania-New Jersey Interconnection Bushkill to Roseland Transmission Line, From Roseland Borough, Essex County, through Morris County and Sussex County to Hardwick Township, Warren County, Roseland, Essex County, NJ

  19. First structure on MoronytoRainbow 100kV Transmission Line below Morony Dam ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    First structure on Morony-to-Rainbow 100kV Transmission Line below Morony Dam and Power House. Three-pole H-frame structure with historic porcelain suspension insulators, jumper supports insulators, overhead ground wires, and pole stubs. View to east-northeast - Morony Hydroelectric Facility, Morony-to-Rainbow 100 kV Transmission Line, West bank of the Missouri River, Great Falls, Cascade County, MT

  20. Optimized Minimal Inductance Transmission Line Configuration for Z-Pinch Experiments

    SciTech Connect

    Hurricane, O

    2003-10-16

    Successful dynamic Z-pinch experiments generally require good current delivery to the target load. Power flow losses through highly inductive transmission line configurations reduce the current available to the load. In this Brief Report, a variational calculus technique is used to determine the transmission line configuration that produces the least possible inductance and therefore the best possible current delivery for Z-pinch experiments.

  1. Finite-difference, time-domain analysis of a folded acoustic transmission line.

    PubMed

    Jackson, Charles M

    2005-03-01

    Recently designed, modern versions of renais sance woodwind instruments such as the recorder and serpent use square cross sections and a folded acoustic transmission line. Conventional microwave techniques would expect that this bend would cause unwanted reflections and impedance discontinuities. This paper analyses the folded acoustic transmission line using finite-difference, time-domain techniques and shows that the discontinuity can be compensated with by the use of a manufacturable method. PMID:15857045

  2. TE sub r azimuthal modes for a biconic transmission line in the small-gap limit

    SciTech Connect

    Johnson, W.A.; Mendel, C.W. Jr.; Seidel, D.B. )

    1992-04-15

    Azimuthally asymmetric modes in a biconic transmission line with a small-gap angle may be approximated by transmission-line-like'' modes. It is shown that the errors in these approximations are second order in the gap angle and approximate error bounds are provided. As an example demonstrating the application of this analysis in biconic structures, an analysis to characterize of the electromagnetic waves in the vacuum feed of the Particle Beam Fusion Accelerator II is provided.

  3. Knee-laxity measurements examined by a left-hand- and a right-hand-dominant physiotherapist, in patients with anterior cruciate ligament injuries and healthy controls.

    PubMed

    Sernert, Ninni; Helmers, Janett; Kartus, Catarina; Ejerhed, Lars; Kartus, Jüri

    2007-10-01

    The purpose of the study was to analyse and compare KT-1000 knee laxity as examined by a left-hand- and a right-hand-dominant physiotherapist in a group of patients with an anterior cruciate ligament (ACL) injury and a group of patients, 2 years after ACL reconstruction. The other aim was to measure and analyse knee laxity in a group of persons without any known knee problems. A cross-sectional examination of two groups of patients pre-operatively and post-operatively after ACL reconstruction and examination of healthy controls on two different occasions was performed. Fifty-three patients who were scheduled for ACL reconstruction and 39 patients who attended a 2-year follow-up examination were included in the study. In the ACL-deficient group, 32 patients had a right-sided ACL injury and 21 patients a left-sided ACL injury. The corresponding figures in the post-operative group were 21 patients with a right-sided ACL injury and 18 patients with a left-sided ACL injury. Twenty-eight healthy persons without any known knee problems served as controls. One left-hand- and one right-hand-dominant experienced physiotherapist performed all the examinations. To be able to evaluate the intra and inter-reliability of the examiners the controls were examined at two occasions. The left-hand-dominant physiotherapist measured significantly higher absolute laxity values in the left knee, both injured and non-injured ones, compared with the right-hand-dominant physiotherapist. This was found irrespectively of whether the patients belonged to the ACL deficient or the post-operative group. In the healthy control group, the right-hand-dominant physiotherapist measured significantly higher knee-laxity values in the right knee compared with the left-hand-dominant physiotherapist. Correspondingly, the left-hand-dominant physiotherapist measured significantly higher knee laxity values in the left knee. We conclude that KT-1000 arthrometer laxity measurements can be affected by the hand

  4. Multisection transmission line scatter function theory for measurements of soil dielectric properties

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Vector network analyzers measure both reflection (S11) and transmission (S21) functions, but S21 has not been used to estimate soil dielectric permittivity independently. The objectives of this study were to: (1) derive the mathematical model for S21 of a multisection transmission line, and (2) tes...

  5. 33 CFR 165.T01-0992 - Safety Zone; repair of high voltage transmission lines to Logan International Airport; Saugus...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... voltage transmission lines to Logan International Airport; Saugus River, Saugus, MA. 165.T01-0992 Section... high voltage transmission lines to Logan International Airport; Saugus River, Saugus, MA. (a) General... high voltage transmission lines to Logan International Airport; Saugus River, Saugus, MA. (i)...

  6. Analysis of optimum diameter of orbit of transmission line source in positron emission tomograph

    SciTech Connect

    Yamamoto, S.; Amano, M.; Hirose, Y.; Muira, S.; Kanno, I.

    1989-02-01

    Accurate attenuation correction is one of the most important factors to achieve quantitative measurements in positron emission tomography (PET). A transmission scan is most commonly used technique for the attenuation correction in PET. A difficulty in transmission scan is relatively long period to obtain a data with good signal-to-noise ratio. Insufficient signal-to-noise ratio of the transmission data limits that of emission data. Several approaches were reported to improve the transmission data. Those were (1) optimizing of detector threshold, (2) processing delayed coincidence sinogram before subtraction, filtering of transmission sinogram before performing attenuation correction, and (3) rejection of random and scatter coincidence by using rotating line source and information of its position. In some of these methods, additional calculation time or processing hardware is needed. The authors have estimated a relationship between ring diameter of a transmission line source and signal to noise ratio of the transmission dat. This paper aimes to analyze optimum diameter of the orbit of transmission line source in concerning to signal to noise ratio in transmission data.

  7. The physical meaning of transmission-line parameters in a full-wave theory

    NASA Astrophysics Data System (ADS)

    Rambousky, Ronald; Nitsch, Jürgen; Tkachenko, Sergey

    2016-09-01

    In the potential-current representation, transmission-line parameters in the Transmission-Line Super Theory (TLST) do not have a direct physical meaning - they are gauge dependent, i.e.: they are different in the Lorenz and Coulomb gauge. However, they retain traces of their classical origin: They are constituted of capacitances and inductances for forward and backward running waves along the lines. Therefore their corresponding matrices are not symmetrical as in the case of classical transmission-line theory. In the charge-current representation the parameter matrices have a physical meaning: their elements consist of damping functions due to the non-uniformities of the lines and of the propagation functions along the lines, incorporating conductor and radiation losses. The transmission line parameters also contribute to the total radiated power of the lines. The attempt to quantize radiation locally, fails because radiation describes a long-range (integral) interaction, and therefore affects all conductor parts of all lines. However, it can be stated that at stronger inhomogeneities the local contributions to radiation increase, and are particularly recognizable along the risers.

  8. Millikelvin thermal and electrical performance of lossy transmission line filters

    SciTech Connect

    Slichter, Daniel; Naaman, Ofer; Siddiqi, Irfan

    2009-03-11

    We report on the scattering parameters and Johnson noise emission of low-pass stripline filters employing a magnetically loaded silicone dielectric down to 25 mK. The transmission characteristic of a device with f-3dB=1.3 GHz remains essentially unchanged upon cooling. Another device with f-edB=0.4 GHz, measured in its stopband, exhibits a steady state noise power emission consistent with a temperature difference of a few mK relative to a well-anchored cryogenic microwave attenuator at temperatures down to 25 mK, thus presenting a matched thermal load.

  9. An additional channel for FM signal transmission in standard fiber-optic AM communication lines

    NASA Astrophysics Data System (ADS)

    Lebedev, V. V.; Anufriev, K. M.; Toguzov, N. V.; Il'ichev, I. V.; Shamray, A. V.

    2015-11-01

    A paradigm has been developed according to which an additional FM signal transfer channel is formed in a standard optical fiber transmission line without violating the main AM channel operation. Using the proposed approach, an RS-232 interface signal has been experimentally transferred via a standard intraobject 100-Mbit Ethernet line based on an SMF-28 single-mode optical fiber.

  10. Measuring the complex permittivity of poultry meat with a planar transmission-line sensor

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A planar transmission-line sensor is used to measure the complex permittivity of chicken breast meat over the frequency range 0.5 – 5 GHz. Results for the permittivity of nine samples of chicken breast meat are compared to results obtained with a commercially available open-ended coaxial-line probe....

  11. Measurement of the Stochastic Electromagnetic Field Coupling into Transmission Lines in a Reverberation Chamber

    NASA Astrophysics Data System (ADS)

    Magdowski, M.; Siddiqui, S.; Vick, R.

    2012-05-01

    The coupling of stochastic electromagnetic fields to a straight and uniform transmission line was measured in a reverberation chamber. Such stochastic fields also appear in large and complex overmoded cavities like aircraft fuse- lages and satellite enclosures. The measurements were carried out with different line lengths over a large frequency range. The results are analyzed with respect to the statistical distribution of the characteristics of the coupled voltage and compared to simulated values. The simulation is based on a transmission line model and a plane wave representation of the field.

  12. Political efficacy and familiarity as predictors of attitudes towards electric transmission lines in the United States

    DOE PAGES

    Joe, Jeffrey C.; Hendrickson, Kelsie; Wong, Maria; Kane, Stephanie L.; Solan, David; Carlisle, Juliet E.; Koehler, David; Ames, Daniel P.; Beazer, Robert

    2016-05-18

    Public opposition to the construction (i.e., siting) of new high voltage overhead transmission lines is not a new or isolated phenomenon. Past research has posited a variety of reasons, applied general theories, and has provided empirical evidence to explain public opposition. The existing literature, while clarifying many elements of the issue, does not yet fully explain the complexities underlying this public opposition phenomenon. As a result, the current study demonstrated how two overlooked factors, people’s sense of political efficacy and their familiarity (i.e., prior exposure) with transmission lines, explained attitudes of support and opposition to siting new power lines.

  13. Transmission line design for a power distribution system at 20 kHz for aircraft

    NASA Technical Reports Server (NTRS)

    Zelby, L. W.; Mathes, J. B.; Shawver, J. W.

    1986-01-01

    A low inductance, low characteristic impedance transmission line was designed for a 20 kHz power distribution system. Several different conductor configurations were considered: strip lines, interdigitated metal ribbons, and standard insulated wires in multiwire configurations (circular and rectangular cylindrical arrangements). The final design was a rectangular arrangement of multiple wires of the same gauge with alternating polarities from wire to wire. This offered the lowest inductance per unit length (on the order of several nanohenries/meter) and the lowest characteristic impedance (on the order of one Ohm). Standard multipin connectors with gold-plated elements were recommended with this transmission line, the junction boxes to be internally connected with flat metal ribbons for low inductance, and the line to be constructed in sections of suitable length. Computer programs for the calculation of inductance of multiwire lines and of capacitances of strip lines were developed.

  14. Terawatt power division and combination using self-magnetically insulated transmission lines

    SciTech Connect

    Crow, J.T.; Peterson, G.D.

    1980-01-01

    Self-magnetically insulated transmission lines are necessary for the efficient transport of the terawatt pulses used in electron and ion accelerators. For some applications it is desirable to divide one transmission line into two, or to combine outputs of two or more lines into one, by means of self-magnetically insulated convolutes. Tests have been made on a coaxial-to-triaxial convolute in which connections between negative inner and outer lines are made by pins passing through holes in the intermediate positive conductor. Measurements in the 2 MV, 400 kA, 40 ns pulse Mite facility indicate virtually 100% current transport through the convolute and the ability to vary the division of current between the inner and outer lines of the triax by choice of inner line impedance. These measurements, and results obtained with this convolute connected to the ion diode for which it was designed, will be presented.

  15. Fiber Optic Picosecond Laser Pulse Transmission Line for Hydrogen Ion Beam Profile Measurement

    SciTech Connect

    Liu, Yun; Huang, Chunning; Aleksandrov, Alexander V

    2013-01-01

    We present a fiber optic laser pulse transmission line for non-intrusive longitudinal profile measurement of the hydrogen ion (H-) beam at the front-end of the Spallation Neutron Source (SNS) accelerator. The 80.5 MHz, 2.5 ps, multi-killowatt optical pulses are delivered to the accelerator beam line through a large mode area polarization maintaining optical fiber to ensure a high measurement stability. The transmission efficiency, output laser beam quality, pulse jitter and pulse width broadening over a 100-ft fiber line are experimentally investigated. A successful measurement of the H- beam microbunch (~130 ps) profile is obtained. Our experiment is the first demonstration of particle beam profile diagnostics using fiber optic laser pulse transmission line.

  16. Fiber optic picosecond laser pulse transmission line for hydrogen ion beam longitudinal profile measurement.

    PubMed

    Huang, Chunning; Liu, Yun; Aleksandrov, Alexander

    2013-07-01

    We present a fiber optic laser pulse transmission line for nonintrusive longitudinal profile measurement of the hydrogen ion (H(-)) beam at the front-end of the Spallation Neutron Source accelerator. The 80.5 MHz, 2.5 ps, multikilowatt optical pulses are delivered to the accelerator beam line through a large-mode-area polarization-maintaining optical fiber to ensure high measurement stability. The transmission efficiency, output laser beam quality, pulse jitter, and pulse width broadening over a 30 m long fiber line are experimentally investigated. A successful measurement of the H(-) beam microbunch (~130 ps) profile is obtained. The experiment is the first demonstration to our knowledge of particle beam profile diagnostics using a fiber optic laser pulse transmission line.

  17. Flashover vulnerability of transmission and distribution lines to high-altitude electromagnetic pulse (HEMP)

    SciTech Connect

    Kruse, V.J.; Liu, T.K.; Tesche, F.M.; Barnes, P.R.

    1989-01-01

    This paper estimates the vulnerability of transmission and distribution lines to flashover from the electromagnetic pulse generated by a nuclear detonation 400 kilometers above the earth. The analysis consists of first determining the cumulative probability of induced-voltage on three-phase lines, including shield and neutral conductors, for four operating voltages and then comparing these stresses to estimates of line insulation strength. 11 refs., 9 figs., 5 tabs.

  18. Assessment of Fecundity and Germ Line Transmission in Two Transgenic Pig Lines Produced by Sleeping Beauty Transposition

    PubMed Central

    Garrels, Wiebke; Holler, Stephanie; Cleve, Nicole; Niemann, Heiner; Ivics, Zoltan; Kues, Wilfried A.

    2012-01-01

    Recently, we described a simplified injection method for producing transgenic pigs using a non-autonomous Sleeping Beauty transposon system. The founder animals showed ubiquitous expression of the Venus fluorophore in almost all cell types. To assess, whether expression of the reporter fluorophore affects animal welfare or fecundity, we analyzed reproductive parameters of two founder boars, germ line transmission, and organ and cell specific transgene expression in animals of the F1 and F2 generation. Molecular analysis of ejaculated sperm cells suggested three monomeric integrations of the Venus transposon in both founders. To test germ line transmission of the three monomeric transposon integrations, wild-type sows were artificially inseminated. The offspring were nursed to sexual maturity and hemizygous lines were established. A clear segregation of the monomeric transposons following the Mendelian rules was observed in the F1 and F2 offspring. Apparently, almost all somatic cells, as well as oocytes and spermatozoa, expressed the Venus fluorophore at cell-type specific levels. No detrimental effects of Venus expression on animal health or fecundity were found. Importantly, all hemizygous lines expressed the fluorophore in comparable levels, and no case of transgene silencing or variegated expression was found after germ line transmission, suggesting that the insertions occurred at transcriptionally permissive loci. The results show that Sleeping Beauty transposase-catalyzed transposition is a promising approach for stable genetic modification of the pig genome. PMID:24705079

  19. Simultaneous formation of right- and left-handed anti-parallel coiled-coil interfaces by a coil2 fragment of human lamin A.

    PubMed

    Kapinos, Larisa E; Burkhard, Peter; Herrmann, Harald; Aebi, Ueli; Strelkov, Sergei V

    2011-04-22

    The elementary building block of all intermediate filaments (IFs) is a dimer featuring a central α-helical rod domain flanked by the N- and C-terminal end domains. In nuclear IF proteins (lamins), the rod domain consists of two coiled-coil segments, coil1 and coil2, that are connected by a short non-helical linker. Coil1 and the C-terminal part of coil2 contain the two highly conserved IF consensus motifs involved in the longitudinal assembly of dimers. The previously solved crystal structure of a lamin A fragment (residues 305-387) corresponding to the second half of coil2 has yielded a parallel left-handed coiled coil. Here, we present the crystal structure and solution properties of another human lamin A fragment (residues 328-398), which is largely overlapping with fragment 305-387 but harbors a short segment of the tail domain. Unexpectedly, no parallel coiled coil forms within the crystal. Instead, the α-helices are arranged such that two anti-parallel coiled-coil interfaces are formed. The most significant interface has a right-handed geometry, which is accounted for by a characteristic 15-residue repeat pattern that overlays with the canonical heptad repeat pattern. The second interface is a left-handed anti-parallel coiled coil based on the predicted heptad repeat pattern. In solution, the fragment reveals only a weak dimerization propensity. We speculate that the C-terminus of coil2 might unzip, thereby allowing for a right-handed coiled-coil interface to form between two laterally aligned dimers. Such an interface might co-exist with a heterotetrameric left-handed coiled-coil assembly, which is expected to be responsible for the longitudinal A(CN) contact.

  20. Left-handed helical preference in an achiral peptide chain is induced by an L-amino acid in an N-terminal type II β-turn.

    PubMed

    De Poli, Matteo; De Zotti, Marta; Raftery, James; Aguilar, Juan A; Morris, Gareth A; Clayden, Jonathan

    2013-03-15

    Oligomers of the achiral amino acid Aib adopt helical conformations in which the screw-sense may be controlled by a single N-terminal residue. Using crystallographic and NMR techniques, we show that the left- or right-handed sense of helical induction arises from the nature of the β-turn at the N terminus: the tertiary amino acid L-Val induces a left-handed type II β-turn in both the solid state and in solution, while the corresponding quaternary amino acid L-α-methylvaline induces a right-handed type III β-turn.

  1. Marys Lake 69/115-kV transmission line upgrade and substation expansion projects

    SciTech Connect

    1996-05-01

    Western Area Power Administration (Western) and the Platte River Power Authority (Platte River) propose to upgrade portions of the existing electric transmission and substation system that serves the Town of Estes Park, Colorado. The existing transmission lines between the Estes Power Plant Switchyard and the Marys Lake Substation include a 115,000 volt (115-kV) line and 69,000 volt (69-kV) line. Approximately one mile is a double-circuit 115/69-kV line on steel lattice structures, and approximately two miles consists of separate single-circuit 115-kV and a 69-kV lines, constructed on wood H-Frame structures. Both lines were constructed in 1951 by the US Bureau of Reclamation. The existing transmission lines are on rights-of-way (ROW) that vary from 75 feet to 120 feet and are owned by Western. There are 48 landowners adjacent to the existing ROW. All of the houses were built adjacent to the existing ROW after the transmission lines were constructed. Upgrading the existing 69-kV transmission line between the Marys Lake Substation and the Estes Power Plant Switchyard to 115-kV and expanding the Marys Lake Substation was identified as the most effective way in which to improve electric service to Estes Park. The primary purpose and need of the proposed project is to improve the reliability of electric service to the Town of Estes Park. Lack of reliability has been a historical concern, and reliability will always be less than desired until physical improvements are made to the electrical facilities serving Estes Park.

  2. Study of transmission line attenuation in broad band millimeter wave frequency range

    SciTech Connect

    Pandya, Hitesh Kumar B.; Austin, M. E.; Ellis, R. F.

    2013-10-15

    Broad band millimeter wave transmission lines are used in fusion plasma diagnostics such as electron cyclotron emission (ECE), electron cyclotron absorption, reflectometry and interferometry systems. In particular, the ECE diagnostic for ITER will require efficient transmission over an ultra wide band, 100 to 1000 GHz. A circular corrugated waveguide transmission line is a prospective candidate to transmit such wide band with low attenuation. To evaluate this system, experiments of transmission line attenuation were performed and compared with theoretical loss calculations. A millimeter wave Michelson interferometer and a liquid nitrogen black body source are used to perform all the experiments. Atmospheric water vapor lines and continuum absorption within this band are reported. Ohmic attenuation in corrugated waveguide is very low; however, there is Bragg scattering and higher order mode conversion that can cause significant attenuation in this transmission line. The attenuation due to miter bends, gaps, joints, and curvature are estimated. The measured attenuation of 15 m length with seven miter bends and eighteen joints is 1 dB at low frequency (300 GHz) and 10 dB at high frequency (900 GHz), respectively.

  3. Preliminary evaluation of space station transmission line in a ring configuration

    NASA Technical Reports Server (NTRS)

    Roth, Mary Ellen

    1990-01-01

    The results of a preliminary evaluation of a space station type transmission line and commercial transmission lines in a ring configuration, are reported. In a ring configuration, each node has two paths for the return current of each wire. The additional path can create an unbalanced condition, where the magnetic fields created by the forward and return currents do not cancel. This evaluation was to quantify the effects of the unbalanced case upon the external fields. The transmission lines evaluated were standard commercial coaxial cables, RG59 and RG213, and a space station designed flat Litz transmission line. Each was evaluated in a balanced and unbalanced mode of operation. Currents and their harmonic content were recorded and compared. As expected, the harmonic content of the different current (I delta) was substantial for the unbalanced case as compared to the balanced case. For the balanced case, very little difference was noted among the various transmission lines evaluated. The evaluation is discussed, and the test circuit, the measurements, and the resulting data are described.

  4. Calculation of transmission line impedances using the ANSYS finite element program

    SciTech Connect

    Johnson, M.E.

    1984-06-29

    This paper describes numerical techniques for calculating the capacitance of an arbitrary two conductor structure. For two dimensional structures the capacitance per unit length can be easily related to the characteristic impedance of a transmission line with the same cross section. Note that this is true for lines operated below their cut off frequency, i.e., TEM mode only. Thus, one can compute the impedance of an arbitrarily shaped line. The method using the ANSYS finite element program is being used to design the high voltage transmission line for the Yale streamer chamber. This line has a transition piece between two different cross sections. It is being modeled by taking several slices throughout the transition region.

  5. Dynamic responses and vibration control of the transmission tower-line system: a state-of-the-art review.

    PubMed

    Chen, Bo; Guo, Wei-hua; Li, Peng-yun; Xie, Wen-ping

    2014-01-01

    This paper presented an overview on the dynamic analysis and control of the transmission tower-line system in the past forty years. The challenges and future developing trends in the dynamic analysis and mitigation of the transmission tower-line system under dynamic excitations are also put forward. It also reviews the analytical models and approaches of the transmission tower, transmission lines, and transmission tower-line systems, respectively, which contain the theoretical model, finite element (FE) model and the equivalent model; shows the advances in wind responses of the transmission tower-line system, which contains the dynamic effects under common wind loading, tornado, downburst, and typhoon; and discusses the dynamic responses under earthquake and ice loads, respectively. The vibration control of the transmission tower-line system is also reviewed, which includes the magnetorheological dampers, friction dampers, tuned mass dampers, and pounding tuned mass dampers. PMID:25105161

  6. Dynamic Responses and Vibration Control of the Transmission Tower-Line System: A State-of-the-Art Review

    PubMed Central

    Chen, Bo; Guo, Wei-hua; Li, Peng-yun; Xie, Wen-ping

    2014-01-01

    This paper presented an overview on the dynamic analysis and control of the transmission tower-line system in the past forty years. The challenges and future developing trends in the dynamic analysis and mitigation of the transmission tower-line system under dynamic excitations are also put forward. It also reviews the analytical models and approaches of the transmission tower, transmission lines, and transmission tower-line systems, respectively, which contain the theoretical model, finite element (FE) model and the equivalent model; shows the advances in wind responses of the transmission tower-line system, which contains the dynamic effects under common wind loading, tornado, downburst, and typhoon; and discusses the dynamic responses under earthquake and ice loads, respectively. The vibration control of the transmission tower-line system is also reviewed, which includes the magnetorheological dampers, friction dampers, tuned mass dampers, and pounding tuned mass dampers. PMID:25105161

  7. Lumped-element model of a tapered transmission line for impedance matching in a pulsed power system

    NASA Astrophysics Data System (ADS)

    Lee, Kun-A.; Ko, Kwang-Cheol

    2016-07-01

    In a pulsed power system, impedance matching is one of the significant factors for increasing the efficiency of the system. One of the most general methods for impedance matching is to use a tapered transmission line. Because the characteristics of a tapered transmission line are changed continuously according to its position, modeling the tapered transmission line by using lumped elements is difficult. In this study, we investigated a tapered transmission line to match the impedance of power supply to that of a load by using lumped elements especially in a pulsed power system. In modeling the tapered transmission line, we used the concept of a transmission, and we introduced an efficient modeling method. We propose a simulation model based on the investigation results. The results of the study will be useful for research on tapered transmission lines.

  8. Dynamic responses and vibration control of the transmission tower-line system: a state-of-the-art review.

    PubMed

    Chen, Bo; Guo, Wei-hua; Li, Peng-yun; Xie, Wen-ping

    2014-01-01

    This paper presented an overview on the dynamic analysis and control of the transmission tower-line system in the past forty years. The challenges and future developing trends in the dynamic analysis and mitigation of the transmission tower-line system under dynamic excitations are also put forward. It also reviews the analytical models and approaches of the transmission tower, transmission lines, and transmission tower-line systems, respectively, which contain the theoretical model, finite element (FE) model and the equivalent model; shows the advances in wind responses of the transmission tower-line system, which contains the dynamic effects under common wind loading, tornado, downburst, and typhoon; and discusses the dynamic responses under earthquake and ice loads, respectively. The vibration control of the transmission tower-line system is also reviewed, which includes the magnetorheological dampers, friction dampers, tuned mass dampers, and pounding tuned mass dampers.

  9. 75 FR 32940 - Request for Proposals for New or Upgraded Transmission Line Projects Under Section 1222 of the...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-06-10

    ... several states. Southwestern operates and maintains 1,380 miles of high voltage transmission lines in... Dakota, Texas, Utah, and Wyoming. Western's 17,000-mile high-voltage transmission system carries... Transmission Line Projects under section 1222 of EPAct (73 FR 70636 and 70638 respectively)....

  10. Effects of high-voltage transmission lines on honey bees

    SciTech Connect

    Greenberg, B.; Bindokas, V.P.

    1981-04-01

    Data are reported on the effect of hive height and current distribution on honey bees hived under a 765 kV line (E-field ca. 7 kV/m). Hive height was standardized with adjustable collectors to 1 meter (59 ..mu..A total hive current) or 1.5 meter (85 ..mu..A) equivalents; controls were shielded. A 1.5 meter group with completely painted supers was included. After 8 or 16 weeks of exposure there was no effect on honey moisture content or weight of young workers in any group. Worker capped brood was not affected in 1 m hives but declined significantly in 1.5 m hives after 4 weeks of exposure and this was associated with queen loss, abnormal queen cell production, and colony failure. Weight gain was depressed in all hives after 2 weeks of exposure and was dose related, with the taller hives more severely affected. Only the exposed hives propolized entrances but the amount and time of onset were not dose related. The 1.5 m hives with painted interiors behaved like the 1 m hives with unpainted interiors in all respects, although their total hive current approximated the other group of 1.5 m hives. Reversal of treatments at midseason resulted in reversal of colony behavior, manifested most clearly with respect to hive weight, less with respect to brood. When first exposed, colonies exhibit pronounced but transient elevations in hive temperature. Bio-effects were more severe during the first period when hives had fewer bees. Total hive current was greater in wet than in dry periods. All these factors influence observed bioeffects.

  11. Kinetic inductance driven nanoscale 2D and 3D THz transmission lines

    NASA Astrophysics Data System (ADS)

    Mousavi, S. Hossein; Williamson, Ian A. D.; Wang, Zheng

    2016-05-01

    We examine the unusual dispersion and attenuation of transverse electromagnetic waves in the few-THz regime on nanoscale graphene and copper transmission lines. Conventionally, such propagation has been considered to be highly dispersive, due to the RC time constant-driven voltage diffusion below 1 THz and plasmonic effects at higher optical frequencies. Our numerical modeling across the microwave, THz, and optical frequency ranges reveals that the conductor kinetic inductance creates an ultra-broadband linear-dispersion and constant-attenuation region in the THz regime. This so-called LC region is an ideal characteristic that is known to be absent in macro-scale transmission lines. The kinetic-LC frequency range is dictated by the structural dimensionality and the free-carrier scattering rate of the conductor material. Moreover, up to 40x wavelength reduction is observed in graphene transmission lines.

  12. Kinetic inductance driven nanoscale 2D and 3D THz transmission lines

    PubMed Central

    Mousavi, S. Hossein; Williamson, Ian A. D.; Wang, Zheng

    2016-01-01

    We examine the unusual dispersion and attenuation of transverse electromagnetic waves in the few-THz regime on nanoscale graphene and copper transmission lines. Conventionally, such propagation has been considered to be highly dispersive, due to the RC time constant-driven voltage diffusion below 1 THz and plasmonic effects at higher optical frequencies. Our numerical modeling across the microwave, THz, and optical frequency ranges reveals that the conductor kinetic inductance creates an ultra-broadband linear-dispersion and constant-attenuation region in the THz regime. This so-called LC region is an ideal characteristic that is known to be absent in macro-scale transmission lines. The kinetic-LC frequency range is dictated by the structural dimensionality and the free-carrier scattering rate of the conductor material. Moreover, up to 40x wavelength reduction is observed in graphene transmission lines. PMID:27137628

  13. Computer simulation of multiple coupled transmission lines in electronic packaging application

    SciTech Connect

    Liao, Jenchyi.

    1989-01-01

    A method for simulating the transient responses of networks containing lossless transmission lines and lumped parameter elements of circuits, both linear and nonlinear, has been developed and investigated. The method combines the technique of network analysis and that of modal decomposition of transmission lines. A prototype computer simulation program, called UANTL, based on the developed algorithm has been implemented. Several example networks have been simulated using this program. The results have been compared with those generated by the well known circuit simulator program called SPICE. UANTL has shown several advantages over SPICE in simulating the transient responses of networks containing transmission lines. A description of the prototype version of UANTL and a summary of the results of numerical experiments are included.

  14. Transmission Line Jobs and Economic Development Impact (JEDI) Model User Reference Guide

    SciTech Connect

    Goldberg, M.; Keyser, D.

    2013-10-01

    The Jobs and Economic Development Impact (JEDI) models, developed through the National Renewable Energy Laboratory (NREL), are freely available, user-friendly tools that estimate the potential economic impacts of constructing and operating power generation projects for a range of conventional and renewable energy technologies. The Transmission Line JEDI model can be used to field questions about the economic impacts of transmission lines in a given state, region, or local community. This Transmission Line JEDI User Reference Guide was developed to provide basic instruction on operating the model and understanding the results. This guide also provides information on the model's underlying methodology, as well as the parameters and references used to develop the cost data contained in the model.

  15. Kinetic inductance driven nanoscale 2D and 3D THz transmission lines.

    PubMed

    Mousavi, S Hossein; Williamson, Ian A D; Wang, Zheng

    2016-05-03

    We examine the unusual dispersion and attenuation of transverse electromagnetic waves in the few-THz regime on nanoscale graphene and copper transmission lines. Conventionally, such propagation has been considered to be highly dispersive, due to the RC time constant-driven voltage diffusion below 1 THz and plasmonic effects at higher optical frequencies. Our numerical modeling across the microwave, THz, and optical frequency ranges reveals that the conductor kinetic inductance creates an ultra-broadband linear-dispersion and constant-attenuation region in the THz regime. This so-called LC region is an ideal characteristic that is known to be absent in macro-scale transmission lines. The kinetic-LC frequency range is dictated by the structural dimensionality and the free-carrier scattering rate of the conductor material. Moreover, up to 40x wavelength reduction is observed in graphene transmission lines.

  16. Kinetic inductance driven nanoscale 2D and 3D THz transmission lines.

    PubMed

    Mousavi, S Hossein; Williamson, Ian A D; Wang, Zheng

    2016-01-01

    We examine the unusual dispersion and attenuation of transverse electromagnetic waves in the few-THz regime on nanoscale graphene and copper transmission lines. Conventionally, such propagation has been considered to be highly dispersive, due to the RC time constant-driven voltage diffusion below 1 THz and plasmonic effects at higher optical frequencies. Our numerical modeling across the microwave, THz, and optical frequency ranges reveals that the conductor kinetic inductance creates an ultra-broadband linear-dispersion and constant-attenuation region in the THz regime. This so-called LC region is an ideal characteristic that is known to be absent in macro-scale transmission lines. The kinetic-LC frequency range is dictated by the structural dimensionality and the free-carrier scattering rate of the conductor material. Moreover, up to 40x wavelength reduction is observed in graphene transmission lines. PMID:27137628

  17. Non-Linear Transmission Line (NLTL) Microwave Source Lecture Notes the United States Particle Accelerator School

    SciTech Connect

    Russell, Steven J.; Carlsten, Bruce E.

    2012-06-26

    We will quickly go through the history of the non-linear transmission lines (NLTLs). We will describe how they work, how they are modeled and how they are designed. Note that the field of high power, NLTL microwave sources is still under development, so this is just a snap shot of their current state. Topics discussed are: (1) Introduction to solitons and the KdV equation; (2) The lumped element non-linear transmission line; (3) Solution of the KdV equation; (4) Non-linear transmission lines at microwave frequencies; (5) Numerical methods for NLTL analysis; (6) Unipolar versus bipolar input; (7) High power NLTL pioneers; (8) Resistive versus reactive load; (9) Non-lineaer dielectrics; and (10) Effect of losses.

  18. Development of an accurate transmission line fault locator using the global positioning system satellites

    NASA Technical Reports Server (NTRS)

    Lee, Harry

    1994-01-01

    A highly accurate transmission line fault locator based on the traveling-wave principle was developed and successfully operated within B.C. Hydro. A transmission line fault produces a fast-risetime traveling wave at the fault point which propagates along the transmission line. This fault locator system consists of traveling wave detectors located at key substations which detect and time tag the leading edge of the fault-generated traveling wave as if passes through. A master station gathers the time-tagged information from the remote detectors and determines the location of the fault. Precise time is a key element to the success of this system. This fault locator system derives its timing from the Global Positioning System (GPS) satellites. System tests confirmed the accuracy of locating faults to within the design objective of +/-300 meters.

  19. Onset of dispersion in Nb microstrip transmission lines at submillimeter wave frequencies

    NASA Technical Reports Server (NTRS)

    Javadi, H. H. S.; Mcgrath, William R.; Bumble, B.; Leduc, Henry G.

    1992-01-01

    We have measured the dispersion in phase velocity of a Nb-SiO(x)-Nb microstrip transmission line resonator over a frequency range from 50 GHz to 800 GHz. A submicron Nb/Al-AlO(x)/Nb Josephson junction was used as a voltage-controlled oscillator to excite the high order modes in the resonator. The same junction is used as a direct detector resulting in a series of step-like structures in the DC current-voltage characteristic at the position of each mode frequency. The transmission line is dispersionless up to about 500 GHz where the phase velocity begins to decrease. This is well below the gap frequency f(sub g) approx. equals 700 GHz. Results agree qualitatively with the expected theoretical behavior near f(sub g). This onset of dispersion and loss in Nb transmission lines will have a significant impact on the design of submillimeter wave RF circuits.

  20. A test of a 2 Tesla superconducting transmission line magnet system

    SciTech Connect

    Piekarz, Henryk; Carcagno, Ruben; Claypool, Brad; Foster, George W.; Hays, Steven L.; Huang, Yuenian; Kashikhin, Vladimir; Malamud, Ernest; Mazur, Peter O.; Nehring, Roger; Oleck, Andrew; Rabehl, Roger; Schlabach, Phil; Sylvester, Cosmore; Velev, Gueorgui; Volk, James; Wake, Masayoshi; /KEK, Tsukuba

    2005-09-01

    Superconducting transmission line magnet test system for an injector accelerator of a staged VLHC proton-proton colliding beam accelerator has been built and operated at Fermilab. The 1.5 m long, twin-aperture, combined function dipole magnet of 2 Tesla field is excited by a single turn 100 kA transmission line superconductor. The 100 kA dc current is generated using dc-dc switching converters powered by a bulk 240 kW supply. A pair of horizontally placed conventional leads facilitates transfer of this current to the magnet transmission line superconductor operating at liquid helium temperature. Fabrication of magnet components and magnet assembly work are described. The magnet test system and its operation are presented, and the performance is summarized.

  1. Lighting up left-handed Z-DNA: photoluminescent carbon dots induce DNA B to Z transition and perform DNA logic operations

    PubMed Central

    Feng, Lingyan; Zhao, Andong; Ren, Jinsong; Qu, Xiaogang

    2013-01-01

    Left-handed Z-DNA has been identified as a transient structure occurred during transcription. DNA B-Z transition has attracted much attention because of not only Z-DNA biological importance but also their relation to disease and DNA nanotechnology. Recently, photoluminescent carbon dots, especially highly luminescent nitrogen-doped carbon dots, have attracted much attention on their applications to bioimaging and gene/drug delivery because of carbon dots with low toxicity, highly stable photoluminescence and controllable surface function. However, it is still unknown whether carbon dots can influence DNA conformation or structural transition, such as B-Z transition. Herein, based on our previous series work on DNA interactions with carbon nanotubes, we report the first example that photoluminescent carbon dots can induce right-handed B-DNA to left-handed Z-DNA under physiological salt conditions with sequence and conformation selectivity. Further studies indicate that carbon dots would bind to DNA major groove with GC preference. Inspired by carbon dots lighting up Z-DNA and DNA nanotechnology, several types of DNA logic gates have been designed and constructed based on fluorescence resonance energy transfer between photoluminescent carbon dots and DNA intercalators. PMID:23814186

  2. Age estimation based on bone length using 12 regression models of left hand X-ray images for Asian children below 19 years old.

    PubMed

    Darmawan, M F; Yusuf, Suhaila M; Abdul Kadir, M R; Haron, H

    2015-03-01

    Age estimation was used in forensic anthropology to help in the identification of individual remains and living person. However, the estimation methods tend to be unique and applicable only to a certain population. This paper analyzed age estimation using twelve regression models carried out on X-ray images of the left hand taken from an Asian data set for subjects under the age of 19. All the nineteen bones of the left hand were measured using free image software and the statistical analysis were performed using SPSS. There are two methods to determine age in this study which are single bone method and all bones method. For single bone method, S-curve regression model was found to have the highest R-square value using second metacarpal for males, and third proximal phalanx for females. For age estimation using single bone, fifth metacarpal from males and fifth proximal phalanx from females can be used due to the lowest mean square error (MSE) value. To conclude, multiple linear regressions is the best techniques for age estimation in cases where all bones are available, but if not, S-curve regression can be used using single bone method. PMID:25456051

  3. A left-hand beta-helix revealed by the crystal structure of a carbonic anhydrase from the archaeon Methanosarcina thermophila.

    PubMed Central

    Kisker, C; Schindelin, H; Alber, B E; Ferry, J G; Rees, D C

    1996-01-01

    A carbonic anhydrase from the thermophilic archaeon Methanosarcina thermophila that exhibits no significant sequence similarity to known carbonic anhydrases has recently been characterized. Here we present the structure of this enzyme, which adopts a left-handed parallel beta-helix fold. This fold is of particular interest since it contains only left-handed crossover connections between the parallel beta-strands, which so far have been observed very infrequently. The active form of the enzyme is a trimer with three zinc-containing active sites, each located at the interface between two monomers. While the arrangement of active site groups differs between this enzyme and the carbonic anhydrases from higher vertebrates, there are structural similarities in the zinc coordination environment, suggestive of convergent evolution dictated by the chemical requirements for catalysis of the same reaction. Based on sequence similarities, the structure of this enzyme is the prototype of a new class of carbonic anhydrases with representatives in all three phylogenetic domains of life. Images PMID:8665839

  4. Tricyclic 1,5-naphthyridinone oxabicyclooctane-linked novel bacterial topoisomerase inhibitors as broad-spectrum antibacterial agents-SAR of left-hand-side moiety (Part-2).

    PubMed

    Singh, Sheo B; Kaelin, David E; Wu, Jin; Miesel, Lynn; Tan, Christopher M; Black, Todd; Nargund, Ravi; Meinke, Peter T; Olsen, David B; Lagrutta, Armando; Lu, Jun; Patel, Sangita; Rickert, Keith W; Smith, Robert F; Soisson, Stephen; Sherer, Edward; Joyce, Leo A; Wei, Changqing; Peng, Xuanjia; Wang, Xiu; Fukuda, Hideyuki; Kishii, Ryuta; Takei, Masaya; Takano, Hisashi; Shibasaki, Mitsuhito; Yajima, Masanobu; Nishimura, Akinori; Shibata, Takeshi; Fukuda, Yasumichi

    2015-05-01

    Novel bacterial topoisomerase inhibitors (NBTIs) represent a new class of broad-spectrum antibacterial agents targeting bacterial Gyrase A and ParC and have potential utility in combating antibiotic resistance. A series of novel oxabicyclooctane-linked NBTIs with new tricyclic-1,5-naphthyridinone left hand side moieties have been described. Compounds with a (R)-hydroxy-1,5-naphthyridinone moiety (7) showed potent antibacterial activity (e.g., Staphylococcus aureus MIC 0.25 μg/mL), acceptable Gram-positive and Gram-negative spectrum with rapidly bactericidal activity. The compound 7 showed intravenous and oral efficacy (ED50) at 3.2 and 27 mg/kg doses, respectively, in a murine model of bacteremia. Most importantly they showed significant attenuation of functional hERG activity (IC50 >170 μM). In general, lower logD attenuated hERG activity but also reduced Gram-negative activity. The co-crystal structure of a hydroxy-tricyclic NBTI bound to a DNA-gyrase complex exhibited a binding mode that show enantiomeric preference for R isomer and explains the activity and SAR. The discovery, synthesis, SAR and X-ray crystal structure of the left-hand-side tricyclic 1,5-naphthyridinone based oxabicyclooctane linked NBTIs are described.

  5. Three new structures of left-handed RADA helical filaments: structural flexibility of N-terminal domain is critical for recombinase activity.

    PubMed

    Chang, Yu-Wei; Ko, Tzu-Ping; Lee, Chien-Der; Chang, Yuan-Chih; Lin, Kuei-Ann; Chang, Chia-Seng; Wang, Andrew H-J; Wang, Ting-Fang

    2009-01-01

    RecA family proteins, including bacterial RecA, archaeal RadA, and eukaryotic Dmc1 and Rad51, mediate homologous recombination, a reaction essential for maintaining genome integrity. In the presence of ATP, these proteins bind a single-strand DNA to form a right-handed nucleoprotein filament, which catalyzes pairing and strand exchange with a homologous double-stranded DNA (dsDNA), by as-yet unknown mechanisms. We recently reported a structure of RadA left-handed helical filament, and here present three new structures of RadA left-handed helical filaments. Comparative structural analysis between different RadA/Rad51 helical filaments reveals that the N-terminal domain (NTD) of RadA/Rad51, implicated in dsDNA binding, is highly flexible. We identify a hinge region between NTD and polymerization motif as responsible for rigid body movement of NTD. Mutant analysis further confirms that structural flexibility of NTD is essential for RadA's recombinase activity. These results support our previous hypothesis that ATP-dependent axial rotation of RadA nucleoprotein helical filament promotes homologous recombination.

  6. Lighting up left-handed Z-DNA: photoluminescent carbon dots induce DNA B to Z transition and perform DNA logic operations.

    PubMed

    Feng, Lingyan; Zhao, Andong; Ren, Jinsong; Qu, Xiaogang

    2013-09-01

    Left-handed Z-DNA has been identified as a transient structure occurred during transcription. DNA B-Z transition has attracted much attention because of not only Z-DNA biological importance but also their relation to disease and DNA nanotechnology. Recently, photoluminescent carbon dots, especially highly luminescent nitrogen-doped carbon dots, have attracted much attention on their applications to bioimaging and gene/drug delivery because of carbon dots with low toxicity, highly stable photoluminescence and controllable surface function. However, it is still unknown whether carbon dots can influence DNA conformation or structural transition, such as B-Z transition. Herein, based on our previous series work on DNA interactions with carbon nanotubes, we report the first example that photoluminescent carbon dots can induce right-handed B-DNA to left-handed Z-DNA under physiological salt conditions with sequence and conformation selectivity. Further studies indicate that carbon dots would bind to DNA major groove with GC preference. Inspired by carbon dots lighting up Z-DNA and DNA nanotechnology, several types of DNA logic gates have been designed and constructed based on fluorescence resonance energy transfer between photoluminescent carbon dots and DNA intercalators.

  7. Suicidal single gunshot injury to the head: differences in site of entrance wound and direction of the bullet path between right- and left-handed--an autopsy study.

    PubMed

    Nikolić, Slobodan; Zivković, Vladimir; Babić, Dragan; Juković, Fehim

    2012-03-01

    The aim of this study was to determine the differences in the anatomical site of a gunshot entrance wound and the direction of the bullet path between right- and left-handed subjects who committed a suicide by a single gunshot injury to the head. The retrospective autopsy study was performed for a 10-year period, and it included selected cases of single suicidal gunshot head injury, committed by handguns. We considered only contact or near-contact wounds. The sample included 479 deceased, with average age 47.1 ± 19.1 years (range, 12-89 years): 432 males and 47 females, with 317 right-handed, 25 left-handed, and 137 subjects with unknown dominant hand. In our observed sample, most cases involved the right temple as the site of entrance gunshot wound (about 67%), followed by the mouth (16%), forehead (7%), left temple (6%), submental (2%), and parietal region (1%). The left temple, right temple, and forehead were the sites of the gunshot entrance wounds, which were the best predictors of the handedness of the deceased (Spearman ρ = 0.149, P = 0.006). Our study showed that the direction of the bullet intracranial path in cases of suicide was even a more potent predictor of the handedness of the deceased (Spearman ρ = 0.263, P = 0.000; Wald = 149.503, P = 0.000).

  8. Simple Correctors for Elimination of High-Order Modes in Corrugated Waveguide Transmission Lines

    PubMed Central

    Kowalski, Elizabeth J.; Shapiro, Michael A.; Temkin, Richard J.

    2014-01-01

    When using overmoded corrugated waveguide transmission lines for high power applications, it is necessary to control the mode content of the system. Ideally, overmoded corrugated transmission lines operate in the fundamental HE11 mode and provide low losses for long distances. Unwanted higher order modes (HOMs), particularly LP11 and HE12, are often excited in the experimental systems due to practical misalignments in the transmission line system. This paper discusses how the unwanted modes propagate along with the fundamental mode in the transmission line system by formulating an equation that relates the center of power offset and angle of propagation of a beam (for the HE11 and LP11 modes) or the waist size and phase front radius of curvature of a beam (for the HE11 and HE12 modes). By introducing two miter bend correctors into the transmission system—miter bends that have slightly angled or ellipsoidal mirrors—the HOMs can be precisely manipulated in the system. This technique can be used to eliminate small quantities of unwanted modes, thereby creating a nearly pure fundamental mode beam with minimal losses. Examples of these applications are calculated and show the theoretical conversion of up to 10% HOM content into the fundamental HE11 mode with minimal losses. PMID:25067859

  9. Measurement of RF Mode Purity in EC Transmission Test Line for ITER

    SciTech Connect

    Oda, Yasuhisa; Kajiwara, Ken; Takahashi, Koji; Kasugai, Atsushi; Sakamoto, Keishi

    2009-11-26

    The transmission mode purity was measured at the ITER relevant transmission line for 170 GHz ECH and CD system. The measured purity of HE{sub 11} in transmission power was 73% and the other was higher order modes. The dominant higher order mode was LP{sub 11} mode (HE{sub 21}+TE{sub 01}). To improve the mode purity, the RF beam coupling in MOU was aligned because LP{sub 11} mode is generated the offset and the tilt angle of RF beam at the waveguide inlet. After the alignment, HE{sub 11} mode purity was increased to 87%.

  10. Quantum transducers: Integrating transmission lines and nanomechanical resonators via charge qubits

    SciTech Connect

    Sun, C. P.; Wei, L. F.; Liu Yuxi; Nori, Franco

    2006-02-15

    We propose a mechanism to interface a transmission line resonator (TLR) with a nanomechanical resonator (NAMR) by commonly coupling them to a charge qubit, a Cooper-pair box with a controllable gate voltage. Integrated in this quantum transducer or simple quantum network, the charge qubit plays the role of a controllable quantum node coherently exchanging quantum information between the TLR and NAMR. With such an interface, a quasiclassical state of the NAMR can be created by controlling a single-mode classical current in the TLR. Alternatively, a 'Cooper pair' coherent output through the transmission line can be driven by a single-mode classical oscillation of the NAMR.

  11. Design Considerations of Fast-cycling Synchrotrons Based on Superconducting Transmission Line Magnets

    SciTech Connect

    Piekarz, H.; Hays, S.; Huang, Y.; Shiltsev, V.; /Fermilab

    2008-06-01

    Fast-cycling synchrotrons are key instruments for accelerator based nuclear and high-energy physics programs. We explore a possibility to construct fast-cycling synchrotrons by using super-ferric, {approx}2 Tesla B-field dipole magnets powered with a superconducting transmission line. We outline both the low temperature (LTS) and the high temperature (HTS) superconductor design options and consider dynamic power losses for an accelerator with operation cycle of 0.5 Hz. We also briefly outline possible power supply system for such accelerator, and discuss the quench protection system for the magnet string powered by a transmission line conductor.

  12. Weld-Windsor 115-kV Transmission Line Project, Weld County, Colorado

    SciTech Connect

    1996-05-01

    The Western Area Power Administration is proposing to rebuild a 3.0 mile segment of the existing Flatiron-Weld 115-kV transmission line in Weld County. The line would be reconductored with new conductor on new wood pole double circuit structures. The new structures would support a double circuit transmission line configuration. The first circuit would be owned by Western and the second by Public Service Company of Colorado (PSCO). Alternatives considered included no action, constructing PSCO`s circuit on new right-of-way, and reconductoring Western`s existing line on the same structures. The proposed action was selected because it provided an opportunity to share structures with PSCO and, overall, would minimize costs and environmental impacts. The environmental assessment identifies minor effects on existing natural or human resources and minor benefits for agricultural operations.

  13. Electrical and mechanical design criteria for EHV and UHV: overhead transmission lines

    SciTech Connect

    Not Available

    1980-06-01

    The results are presented of a program devoted to the selection of electrical and mechanical design criteria and parameters for overhead power transmission lines for ac systems rated at from 345 to 1100 kV and for dc systems rated at from 600 to 1200 kV. Information is included on the environmental effects, i.e., audible noise and electric fields, of the lines, mechanical and economic requirements, safety, failures, grounding, and lightning protection. (LCL)

  14. Grand Coulee - Bell 500-kV Transmission Line Project, Draft Environmental Impact Statement

    SciTech Connect

    N /A

    2002-08-09

    BPA is proposing to construct a 500-kilovolt (kV) transmission line that would extend approximately 84 miles between the Grand Coulee 500-kV Switchyard, near Grand Coulee Dam, and the Bell Substation, in Mead just north of Spokane. The new line would cross portions of Douglas, Grant, Lincoln, and Spokane counties. In addition to the transmission line, new equipment would be installed at the substations at each end of the new line and at other facilities. The proposed action would remove an existing 115-kV transmission line and replace it with the new 500-kV line on existing right-of-way for most of its length. Additional right-of-way would be needed in the first 3.5 miles out of the Grand Coulee Switchyard to connect to the existing 115-kV right-of-way. Since the mid-1990s, the transmission path west of Spokane, called the West of Hatwai transmission pathway, has grown increasingly constrained. To date, BPA has been able to manage operation of the path through available operating practices, and customer needed have been met while maintaining the reliability of the path. however, in early 2001, operations showed that the amount of electricity that needs to flow from east to west along this path creates severe transmission congestion. Under these conditions, the system is at risk of overloads and violation of industry safety and reliability standards. The problem is particularly acute in the spring and summer months because of the large amount of power generated by dams east of the path. Large amounts of water cannot be spilled during that time in order for BPA to fulfill its obligation to protect threatened and endangered fish. The amount of power that needs to move through this area during these months at times could exceed the carrying capacity of the existing transmission lines. In additional capacity is not added, BPA will run a significant risk that it will not be able to continue to meet its contractual obligations to deliver power and maintain reliability

  15. Decoding method for T1 line format for ccitt 32K bit per second adpcm clear channel transmission and 64 KBPS clear channel transmission

    SciTech Connect

    Blondeau, E.E. Jr.; Czarnecki, S.J.

    1988-05-24

    In a data transmission system having first and second digital switching systems connected via T1 line transmission facilities for bidirectional data transmissions, a decoding method for T1 line zero bit suppression is described comprising the steps of: receiving an encoded T1 line frame including bundled channels; testing indicator bits of the received T1 line frame to determine whether any channel of the T1 line frame has been altered for the transmission; first transferring the received T1 line frame as received, performed in response to the indicated bits showing that no alteration have been made to the received T1 line frame; decoding mapping bits of the received T1 line frame to determine which channels of the bundle of the received T1 line frame have been altered for the encoded transmission; replacing the contents of each of the altered channel of the bundle with zeroes; iterating the steps of decoding and replacing for each of the bundles of the received T1 line frame; and second transferring the received T1 line frame with the altered channels being replaced with zeroes.

  16. On-chip sub-terahertz surface plasmon polariton transmission lines in CMOS

    PubMed Central

    Liang, Yuan; Yu, Hao; Zhang, Hao Chi; Yang, Chang; Cui, Tie Jun

    2015-01-01

    A low-loss and low-crosstalk surface-wave transmission line (T-line) is demonstrated at sub-THz in CMOS. By introducing periodical sub-wavelength structures onto the metal transmission line, surface plasmon polaritons (SPP) are excited and propagate signals via a strongly localized surface wave. Two coupled SPP T-lines and two quasi-TEM T-lines are both fabricated on-chip, each with a separation distance of 2.4 μm using standard 65 nm CMOS technology. Measurement results show that the SPP T-lines achieve wideband reflection coefficient lower than −14 dB and crosstalk ratio better than −24 dB, which is 19 dB lower on average than the traditional T-lines from 220 GHz to 325 GHz. The demonstrated compact and wideband SPP T-lines have shown great potential for future realization of highly dense on-chip sub-THz communications in CMOS. PMID:26445889

  17. Canby Area Service Project : Substation and Associated Transmission Line : Environmental Assessment.

    SciTech Connect

    United States. Bonneville Power Administration.

    1992-02-01

    Bonneville Power Administration (BPA) provides power to Surprise Valley Electrification Corporation (SVEC) in Modoc County, California. BPA uses PacificCorp's substation and transmission facilities between Alturas and Canby, California to transfer power to SVEC's Canby Substation. In the next year, SVEC expects increased industrial, agricultural, and residential electric loads on their 69-kV transmission system south of Canby. SVEC's substation can accommodate only about 10 percent of the expected additional electric load. BPA's proposed action is intended to meet SVEC's increasing electric load. BPA proposes to meet SVEC's increasing energy load by tapping into BPA's existing BPA Malin-Warner 230-kV transmission line, and building an 7.9-mile transmission line to a new BPA substation. BPA proposes to build the new substation next to the west side of SVEC's Canby Substation (Figure 1). This new substation will allow SVEC to move the additional power over their existing transmission or distribution lines. This report is the environmental assessment of the potential impact of the proposed project. The assessment determined that no environmental impact statement'' is not required.

  18. Canby Area Service Project substation and associated transmission line. Environmental Assessment

    SciTech Connect

    Not Available

    1992-02-01

    Bonneville Power Administration (BPA) provides power to Surprise Valley Electrification Corporation (SVEC) in Modoc County, California. BPA uses PacificCorp`s substation and transmission facilities between Alturas and Canby, California to transfer power to SVEC`s Canby Substation. In the next year, SVEC expects increased industrial, agricultural, and residential electric loads on their 69-kV transmission system south of Canby. SVEC`s substation can accommodate only about 10 percent of the expected additional electric load. BPA`s proposed action is intended to meet SVEC`s increasing electric load. BPA proposes to meet SVEC`s increasing energy load by tapping into BPA`s existing BPA Malin-Warner 230-kV transmission line, and building an 7.9-mile transmission line to a new BPA substation. BPA proposes to build the new substation next to the west side of SVEC`s Canby Substation (Figure 1). This new substation will allow SVEC to move the additional power over their existing transmission or distribution lines. This report is the environmental assessment of the potential impact of the proposed project. The assessment determined that no ``environmental impact statement`` is not required.

  19. Sound Transmission Through Multi-Panel Structures Lined with Elastic Porous Materials

    NASA Astrophysics Data System (ADS)

    Bolton, J. S.; Shiau, N.-M.; Kang, Y. J.

    1996-04-01

    Theory and measurements related to sound transmission through double panels lined with elastic porous media are presented. The information has application to the design of noise control barriers and to the optimization of aircraft fuselage transmission loss, for example. The major difference between the work described here and earlier research in this field relates to the treatment of the porous material that is used to line the cavity between the two panels of the double panel structure. Here we have used the porous material theory proposed by Biot since it takes explicit account of all the wave types known to propagate in elastic porous materials. As a result, it is possible to use the theory presented here to calculate the transmission loss of lined double panels at arbitrary angles of incidence; results calculated over a range of incidence angles may then be combined to yield the random incidence transmission loss. In this paper, the equations governing wave propagation in an elastic porous material are first considered briefly and then the general forms for the stresses and displacements within the porous material are given. Those solutions are expressed in terms of a number of constants that can be determined by application of appropriate boundary conditions. The boundary conditions required to model double panels having linings that are either directly attached to the facing panels or separated?!from them by air gaps are presented and discussed. Measurements of the random incidence transmission loss of aluminium double-panel structures lined with polyurethane foam are presented and have been found to be in good agreement with theoretical predictions. Both the theoretical predictions and the measured results have shown that the method by which an elastic porous lining material is attached to the facing panels can have a profound influence on the transmission loss of the panel system. It has been found, for example, that treatments in which the lining material

  20. Measuring the complex permittivity tensor of uniaxial biological materials with coplanar waveguide transmission line

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A simple and accurate technique is described for measuring the uniaxial permittivity tensor of biological materials with a coplanar waveguide transmission-line configuration. Permittivity tensor results are presented for several chicken and beef fresh meat samples at 2.45 GHz....

  1. Multiwavelet packet entropy and its application in transmission line fault recognition and classification.

    PubMed

    Liu, Zhigang; Han, Zhiwei; Zhang, Yang; Zhang, Qiaoge

    2014-11-01

    Multiwavelets possess better properties than traditional wavelets. Multiwavelet packet transformation has more high-frequency information. Spectral entropy can be applied as an analysis index to the complexity or uncertainty of a signal. This paper tries to define four multiwavelet packet entropies to extract the features of different transmission line faults, and uses a radial basis function (RBF) neural network to recognize and classify 10 fault types of power transmission lines. First, the preprocessing and postprocessing problems of multiwavelets are presented. Shannon entropy and Tsallis entropy are introduced, and their difference is discussed. Second, multiwavelet packet energy entropy, time entropy, Shannon singular entropy, and Tsallis singular entropy are defined as the feature extraction methods of transmission line fault signals. Third, the plan of transmission line fault recognition using multiwavelet packet entropies and an RBF neural network is proposed. Finally, the experimental results show that the plan with the four multiwavelet packet energy entropies defined in this paper achieves better performance in fault recognition. The performance with SA4 (symmetric antisymmetric) multiwavelet packet Tsallis singular entropy is the best among the combinations of different multiwavelet packets and the four multiwavelet packet entropies.

  2. 49 CFR 192.476 - Internal corrosion control: Design and construction of transmission line.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Internal corrosion control: Design and construction of transmission line. 192.476 Section 192.476 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PIPELINE SAFETY TRANSPORTATION...

  3. 76 FR 15970 - Central Ferry to Lower Monumental 500-kilovolt Transmission Line Project

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-03-22

    ... AGENCY: Bonneville Power Administration (BPA), Department of Energy (DOE). ACTION: Notice of Availability..., and Walla Walla counties, Washington. BPA has decided to implement the Combination A Alternative... single- circuit transmission line from BPA's new Central Ferry Substation near the Port of Central...

  4. Exact Solutions for a Local Fractional DDE Associated with a Nonlinear Transmission Line

    NASA Astrophysics Data System (ADS)

    Aslan, İsmail

    2016-09-01

    Of recent increasing interest in the area of fractional calculus and nonlinear dynamics are fractional differential-difference equations. This study is devoted to a local fractional differential-difference equation which is related to a nonlinear electrical transmission line. Explicit traveling wave solutions (kink/antikink solitons, singular, periodic, rational) are obtained via the discrete tanh method coupled with the fractional complex transform.

  5. Effect of discontinuities on the group delay of a microwave transmission line

    NASA Technical Reports Server (NTRS)

    Beatty, R. W.; Otoshi, T. Y.

    1975-01-01

    The problem is considered of the effect of reflections from discontinuities at each end of a transmission line on the group delay at microwave frequencies. Previous work is briefly reviewed and a general analysis is made. Graphical data are presented based upon the formulas developed. Experimental results are given which confirm the theory.

  6. Position-momentum-entangled photon pairs in nonlinear waveguides and transmission lines

    NASA Astrophysics Data System (ADS)

    Sherkunov, Y.; Whittaker, David M.; Fal'ko, Vladimir

    2016-04-01

    We analyze the correlation properties of light in nonlinear waveguides and transmission lines, predict the position-momentum realization of the Einstein-Podolsky-Rosen paradox for photon pairs in Kerr-type nonlinear photonic circuits, and we show how two-photon entangled states can be generated and detected.

  7. Efficient design of multituned transmission line NMR probes: the electrical engineering approach.

    PubMed

    Frydel, J A; Krzystyniak, M; Pienkowski, D; Pietrzak, M; de Sousa Amadeu, N; Ratajczyk, T; Idzik, K; Gutmann, T; Tietze, D; Voigt, S; Fenn, A; Limbach, H H; Buntkowsky, G

    2011-01-01

    Transmission line-based multi-channel solid state NMR probes have many advantages regarding the cost of construction, number of RF-channels, and achievable RF-power levels. Nevertheless, these probes are only rarely employed in solid state-NMR-labs, mainly owing to the difficult experimental determination of the necessary RF-parameters. Here, the efficient design of multi-channel solid state MAS-NMR probes employing transmission line theory and modern techniques of electrical engineering is presented. As technical realization a five-channel ((1)H, (31)P, (13)C, (2)H and (15)N) probe for operation at 7 Tesla is described. This very cost efficient design goal is a multi port single coil transmission line probe based on the design developed by Schaefer and McKay. The electrical performance of the probe is determined by measuring of Scattering matrix parameters (S-parameters) in particular input/output ports. These parameters are compared to the calculated parameters of the design employing the S-matrix formalism. It is shown that the S-matrix formalism provides an excellent tool for examination of transmission line probes and thus the tool for a rational design of these probes. On the other hand, the resulting design provides excellent electrical performance. From a point of view of Nuclear Magnetic Resonance (NMR), calibration spectra of particular ports (channels) are of great importance. The estimation of the π/2 pulses length for all five NMR channels is presented.

  8. Determination of complex permittivity from propagation constant measurement with planar transmission lines

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A new two-standard calibration procedure is outlined for determining the complex permittivity of materials from the propagation constant measured with planar transmission lines. Once calibrated, a closed-form expression for the material permittivity is obtained. The effects of radiation and conducto...

  9. Frequency considerations in evaluation of geomagnetically induced currents in transmission lines

    NASA Astrophysics Data System (ADS)

    Trichtchenko, Larisa

    2016-04-01

    Significant impacts of large geomagnetically induced currents on power transmission systems lead to the necessity to properly evaluate the size of these currents. Several simplified assumptions which are used for the modelling of these currents would be clarified in the presentations. The following two classes of possible sources of errors will be discussed: 1. "Geophysical" uncertainties in the evaluation of the earth geoelectric field, such as a) influence of geomagnetic sampling rate on the "true" waveform of the geomagnetic disturbance and b) influence of the uncertainties in the 1-dimensional layered earth models; 2. Assumptions in the power network modelling, such as a) DC-approximation of the response of transmission line and b) not taking into accounts the impacts of the conducting system (transmission lines) on the ambient (geophysical) electric field. The results of presented research will help in proper evaluations of the GIC and, therefore, in preparing the adequate mitigation measures to counteract the space weather impacts on critical infrastructure.

  10. Advances in fibers and transmission line technology for long haul submarine systems

    NASA Astrophysics Data System (ADS)

    Peckham, David W.; Kim, Jinkee; Sun, Yi; Lingle, Robert L., Jr.; Levring, Ole

    2007-11-01

    The 7.1-magnitude earthquake on December 26, 2006 in the Strait of Luzon resulted in the failure of several submarine cable systems. Seven of the nine cables that pass through the strait were damaged, disrupting communications to China, Taiwan, Japan, Korea and Singapore. This recent event highlighted the dependence of international communications on submarine fiber optic transmission systems. This paper will review the evolution of optical fiber transmission line technology that has been deployed in the long haul undersea telecommunications network. It will start with a discussion of the chronological evolution of the optical fiber transmission line architecture in section one, then give more detail regarding the technology that is still being deployed today.

  11. Theoretical limit of repeater spacing in an optical transmission line utilizing Raman amplification

    NASA Astrophysics Data System (ADS)

    Nakashima, T.; Seikai, S.; Nakazawa, M.; Negishi, Y.

    1986-08-01

    The limit of repeater spacing is investigated theoretically for optical transmission lines utilizing stimulated Raman scattering to amplify the signal light. Achievable repeater spacing is numerically estimated on the basis of coupled power equations and measured fiber characteristics for various signal wavelengths and relative index differences. Three types of transmission line configurations are considered, i.e., utilization of forward only, backward only, and bidirectional amplification. In the third case, a transmission distance of more than 400 km is predicted for an input signal light power of 100 microW, a signal wavelength of 1.57 microns, and a pump power of 0.5 W using a fiber with a relative index difference of 1 percent for signal light amplification.

  12. Identification and characterization of populations living near high-voltage transmission lines: a pilot study.

    PubMed Central

    Wartenberg, D; Greenberg, M; Lathrop, R

    1993-01-01

    Populations living close to high-voltage transmission lines often have residential magnetic field exposures in excess of 1 microT, and sometimes over 2 microT. Yet, populations studied in most epidemiologic investigations of the association between residential magnetic field exposure and cancer typically have exposures below 1 microT and frequently below 0.5 microT. To improve statistical power and precision, it would be useful to compare high exposure populations with low exposure populations rather than only studying small differences within low exposure populations. Toward this end, we have developed an automated method for identifying populations living near high-voltage transmission lines. These populations likely have more highly exposed individuals than the population at large. The method uses a geographic information system (GIS) to superimpose digitized transmission line locations on U.S. Census block location data and then extract relevant demographic data. Analysis of data from a pilot study of the populations residing within 100 m of a 29-km segment of one 230-kV line in New Jersey shows that when compared to populations in the surrounding census blocks farther than 100 m from this line, those populations close to the line have similar demographics but differ in terms of perceived housing value variables. We believe that the approach we have developed will enable investigators to rapidly identify and characterize populations living near high-voltage transmission lines on a statewide basis for considering the impact of exposures and for public policy and that these populations also can be used for epidemiologic study. Images p626-a Figure 1. Figure 2. Figure 3. PMID:8143596

  13. The Left Hand Second to Fourth Digit Ratio (2D:4D) Does Not Discriminate World-Class Female Gymnasts from Age Matched Sedentary Girls

    PubMed Central

    Peeters, Maarten W.; Claessens, Albrecht L.

    2012-01-01

    Introduction The second to fourth-digit-ratio (2D:4D), a putative marker of prenatal androgen action and a sexually dimorphic trait, has been suggested to be related with sports performance, although results are not univocal. If this relation exists, it is most likely to be detected by comparing extreme groups on the continuum of sports performance. Methods In this study the 2D:4D ratio of world-class elite female artistic gymnasts (n = 129), competing at the 1987 Rotterdam World-Championships was compared to the 2D:4D ratio of sedentary age-matched sedentary girls (n = 129), alongside with other anthropometric characteristics including other sexually dimorphic traits such as an androgyny index (Bayer & Bayley) and Heath-Carter somatotype components (endomorphy, mesomorphy, ectomorphy) using AN(C)OVA. 2D:4D was measured on X-rays of the left hand. Results Left hand 2D:4D digit ratio in world class elite female gymnasts (0.921±0.020) did not differ significantly from 2D:4D in age-matched sedentary girls (0.924±0.018), either with or without inclusion of potentially confounding covariates such as skeletal age, height, weight, somatotype components or androgyny index. Height (161.9±6.4 cm vs 155.4±6.6 cm p<0.01), weight (53.9±7.6 kg vs 46.2 6.3 kg p<0.01), BMI (20.51±2.41 kg/m2 vs 19.05±1.56 kg/m2), skeletal age (15.2±1.1 y vs 14.5±1.2 y p>0.01), somatotype components (4.0/3.0/2.9 vs 1.7/3.7/3.2 for endomorphy (p<0.01), mesomorphy (p<0.01) and ectomorphy (p<0.05) respectively) all differed significantly between sedentary girls and elite gymnasts. As expressed by the androgyny index, gymnasts have, on average, broader shoulders relative to their hips, compared to the reference sample. Correlations between the 2D:4D ratio and chronological age, skeletal age, and the anthropometric characteristics are low and not significant. Conclusion Although other anthropometric characteristics of sexual dimorphism were significantly different between the two samples

  14. Analysis and Experimental Evaluation of Power Line Transmission Parameters for Power Line Communication

    NASA Astrophysics Data System (ADS)

    Mlynek, P.; Misurec, J.; Koutny, M.; Fujdiak, R.; Jedlicka, T.

    2015-04-01

    The article describes a way of evaluating the power line channel frequency response and input impedance by means of the linear time-invariant (LTI) power line generator. Two possible methods are introduced for the calculation of primary parameters: the first method depends on the physical realization and physical dimension of the cable, and the second method is derived from the data provided by typical electrical cable manufacturers. Based on these methods, a comparison of transfer functions was made. This is followed by measurement evaluation and numerical verification on a simple topology

  15. Results of TLMRC research on x-bracing strength in lattice transmission towers. [Transmission Line Mechanical Research Center

    SciTech Connect

    Cannon, D.D. Jr.; Nickerson, R. )

    1993-01-01

    The generally accepted procedures for designing lattice transmission towers in the US are those given in the American Society of Civil Engineers (ASCE) guide, Guide for Design of Steel Transmission Towers (ASCE Manual 52). When the ASCE Task Committee on updating Manual 52 was active prior to publishing the second edition, a topic of discussion and disagreement was the calculation of the strength of X-bracing members. The primary point of disagreement was the effect of the tension member load on the support offered to the compression member and how this should be accounted for in calculating the capacity of the compression member. To clarify the design of X-bracing, EPRI's Transmission Line Mechanical Research Center (TLMRC) initiated a research program to study the strength of X-bracing, with particular emphasis on the effect of the tension member load on the capacity of the compression member. A two-dimensional test frame was used to test X-braces constructed of equal leg angles, unequal leg angles framed either on the long le or on the short leg.

  16. Theory and simulation of high-power microwave generation in a magnetically insulated transmission line oscillator

    NASA Astrophysics Data System (ADS)

    Lemke, Raymond W.; Clark, Collins M.

    1987-10-01

    The magnetically insulated transmission line (MITE-LINE) oscillator is an electron beam diode comprised of a field emitting cathode and a corrugated anode. The device is similar to a linear magnetron except that the insulating magnetic field is self-generated. The self-insulating property makes this device a robust high-power microwave tube. Using the thin-beam approximation a dispersion relation for a cylindrical MITE-LINE oscillator is derived. The dispersion relation is used to predict frequency and growth rate of the microwave generating instability. Analytical results are compared with CCUBE particle simulations.

  17. Sidney-North Yuma 230-kV Transmission Line Project, Colorado and Nebraska

    SciTech Connect

    Not Available

    1991-06-01

    This report describes the need for a 230-kV overhead transmission line to supply power from Sidney, Nebraska to eastern Colorado. The alternative scenario compared to construction of the line is No Action. Rejected alternatives include underground lines and different routing paths, with a possible extension to the Sterling area. Both scenarios are evaluated for environmental effects, cost, and consequences for the eastern Colorado region. The proposed route is determined to be the environmentally preferred choice. 120 refs., 6 figs., 13 tabs. (MHB)

  18. Space charge drift from a +/- 400-kV direct current transmission line.

    PubMed

    Hendrickson, R C

    1986-01-01

    The Minnesota Environmental Quality Board completed a 3-year study of the space charge plume outside the right of way of a bipolar (+/- 400 kV) direct current transmission line in rural west central Minnesota. The purpose of the study was to determine the levels of DC potential gradient and small airs ions in the downwind plume to which humans and animals may be exposed. Potential gradient measurements show that a space charge plume is detectable downwind at least 1600 m from the transmission line. Plume relaxation rates indicate that under certain conditions one could detect the plume at twice that distance or more. Net charge in the plume assumes the polarity of the downwind energized transmission line conductor. The bipolar DC line thus electrically bisects the land through which it passes; on one side of the line there is a net positive space charge, on the other side a net negative space charge. Electric charge in the plume resides on aerosols and small air ions. Polar conductivity data substantiate the fact that small air ions of one polarity in the plume are elevated while those of opposite polarity are suppressed compared to background concentrations found in the rural environment. The resulting charge imbalance persists downwind at least 1600 m, though the median small air ion concentrations of plume polarity have adjusted to within the background range by that time with perpendicular wind speed components between 1 and 6 m/sec.

  19. Multivariable time series prediction for the icing process on overhead power transmission line.

    PubMed

    Li, Peng; Zhao, Na; Zhou, Donghua; Cao, Min; Li, Jingjie; Shi, Xinling

    2014-01-01

    The design of monitoring and predictive alarm systems is necessary for successful overhead power transmission line icing. Given the characteristics of complexity, nonlinearity, and fitfulness in the line icing process, a model based on a multivariable time series is presented here to predict the icing load of a transmission line. In this model, the time effects of micrometeorology parameters for the icing process have been analyzed. The phase-space reconstruction theory and machine learning method were then applied to establish the prediction model, which fully utilized the history of multivariable time series data in local monitoring systems to represent the mapping relationship between icing load and micrometeorology factors. Relevant to the characteristic of fitfulness in line icing, the simulations were carried out during the same icing process or different process to test the model's prediction precision and robustness. According to the simulation results for the Tao-Luo-Xiong Transmission Line, this model demonstrates a good accuracy of prediction in different process, if the prediction length is less than two hours, and would be helpful for power grid departments when deciding to take action in advance to address potential icing disasters. PMID:25136653

  20. Data-Mining-Based Intelligent Differential Relaying for Transmission Lines Including UPFC and Wind Farms.

    PubMed

    Jena, Manas Kumar; Samantaray, Subhransu Ranjan

    2016-01-01

    This paper presents a data-mining-based intelligent differential relaying scheme for transmission lines, including flexible ac transmission system device, such as unified power flow controller (UPFC) and wind farms. Initially, the current and voltage signals are processed through extended Kalman filter phasor measurement unit for phasor estimation, and 21 potential features are computed at both ends of the line. Once the features are extracted at both ends, the corresponding differential features are derived. These differential features are fed to a data-mining model known as decision tree (DT) to provide the final relaying decision. The proposed technique has been extensively tested for single-circuit transmission line, including UPFC and wind farms with in-feed, double-circuit line with UPFC on one line and wind farm as one of the substations with wide variations in operating parameters. The test results obtained from simulation as well as in real-time digital simulator testing indicate that the DT-based intelligent differential relaying scheme is highly reliable and accurate with a response time of 2.25 cycles from the fault inception.