Removal kinetics for gaseous NO and SO2 by an aqueous NaClO2 solution mist in a wet electrostatic precipitator.

PubMed

Park, Hyun-Woo; Park, Dong-Wha

2017-04-01

Removal kinetics for NO and SO 2 by NaClO 2 solution mist were investigated in a wet electrostatic precipitator. By varying the molar concentrations of NO, SO 2 , and NaClO 2 , the removal rates of NO and SO 2 confirmed to range from 34.8 to 72.9 mmol/m 3  s and 36.6 to 84.7 mmol/m 3  s, respectively, at a fixed gas residence time of 0.25 s. The rate coefficients of NO and SO 2 were calculated to be 0.679 (mmol/m 3 ) -0.33  s -1 and 1.401 (mmol/m 3 ) -0.1  s -1 based on the rates of the individual removal of NO and SO 2 . Simultaneous removal of NO and SO 2 investigated after the evaluation of removal rates for their individual treatment was performed. At a short gas residence time, SO 2 gas removed more quickly by a mist of NaClO 2 solution than NO gas in simultaneous removal experiments. This is because SO 2 gas, which has a relatively high solubility in solution, was absorbed more rapidly at the gas-liquid interface than NO gas. NO and SO 2 gases were absorbed as nitrite [Formula: see text] and sulfite [Formula: see text] ions, respectively, by the NaClO 2 solution mist at the gas-liquid interface. Then, [Formula: see text] and [Formula: see text] were oxidized to nitrate [Formula: see text] and sulfate [Formula: see text], respectively, by reactions with [Formula: see text], ClO 2 , HClO, and ClO in the liquid phase.

Sampling Odor Substances by Mist-Cyclone System

NASA Astrophysics Data System (ADS)

Matsubara, Osamu; Jiang, Zhiheng; Toyama, Shigeki

2009-05-01

Many techniques have been developed to measure odor substances. However most of those methods are based on using aquatic solutions(1),(2). Many odor substances specifically at low density situation, are difficult to dissolve into water. To absorb odor substances and obtain highest concentration solutions are key problems for olfactory systems. By blowing odor substances contained air mixture through mist of water and then separating the liquid from two-phases fluid with a cyclone unit a high concentration solution was obtained.

Mega-supramolecules for safer, cleaner fuel

NASA Astrophysics Data System (ADS)

Kornfield, Julie

Guided by the statistical mechanics of ring-chain equilibrium, we designed and synthesized polymers that self-assemble into ``mega-supramolecules'' (>=5,000 kg/mol) at low concentration (<=0.3%wt) in hydrocarbon liquids. Experimental results accord with model predictions that end-functional polymers, which distribute among cyclic and linear supramolecules, can form a significant population of mega-supramolecules at low total polymer concentration--if, and only if , the backbones are long (>400 kg/mol) and end-association strength is optimal (16-18kT). Hydrocarbon liquid fuels are the world's dominant power source (34% of global energy consumption). Transportation relies heavily on such liquids, presenting the risk of explosive post-impact fires. The collapse of the World Trade Center on September 11, 2001 inspired us to revisit polymers for mist control to mitigate post-impact fuel explosions. Rheological and both light and neutron scattering measurements of long end-functional polymers having polycyclooctadiene backbones and acid or amine end groups verify formation of mega-supramolecules. Post-impact flame propagations experiments show that mega-supramolecules control misting. Turbulent flow measurements show that mega-supramolecules reduce drag like ultra-long covalent polymers. With individual building blocks short enough to avoid hydrodynamic chain scission (400

Artemisinin production by plant hairy root cultures in gas- and liquid-phase bioreactors.

PubMed

Patra, Nivedita; Srivastava, Ashok K

2016-01-01

Alternative biotechnological protocol for large-scale artemisinin production was established. It featured enhanced growth and artemisinin production by cultivation of hairy roots in nutrient mist bioreactor (NMB) coupled with novel cultivation strategies. Artemisinin is used for the treatment of cerebral malaria. Presently, its main source is from seasonal plant Artemisia annua. This study featured investigation of growth and artemisinin production by A. annua hairy roots (induced by Agrobacterium rhizogenes-mediated genetic transformation of explants) in three bioreactor configurations-bubble column reactor, NMB and modified NMB particularly to establish their suitability for commercial production. It was observed that cultivation of hairy roots in a non-stirred bubble column reactor exhibited a biomass accumulation of 5.68 g/l only while batch cultivation in a custom-made NMB exhibited a higher biomass concentration of 8.52 g/l but relatively lower artemisinin accumulation of 0.22 mg/g was observed in this reactor. A mixture of submerged liquid-phase growth (for 5 days) followed by gas-phase cultivation in nutrient mist reactor operation strategy (for next 15 days) was adopted for hairy root cultivation in this investigation. Reasonably, high (23.02 g/l) final dry weight along with the artemisinin accumulation (1.12 mg/g, equivalent to 25.78 mg/l artemisinin) was obtained in this bioreactor, which is the highest reported artemisinin yield in the gas-phase NMB cultivation.

Dielectric properties of Ba0.6Sr0.4TiO3 thin films deposited by mist plasma evaporation using aqueous solution precursor

NASA Astrophysics Data System (ADS)

Huang, Hui; Shi, Peng; Wang, Minqiang; Yao, Xi; Tan, O. K.

2006-06-01

Mist plasma evaporation (MPE) technique has been developed to deposit Ba0.6Sr0.4TiO3 (BST) thin films on SiO2/Si and Pt/Ti/SiO2/Si substrates at atmospheric pressure using metal nitrate aqueous solution as precursor. MPE is characterized by the injection of liquid reactants into thermal plasma where the source materials in the droplets are evaporated by the high temperature of the thermal plasma. Nanometer-scale clusters are formed in the tail flame of the plasma, and then deposited and rearranged on the substrate at a lower temperature. Due to the high temperature annealing process of the thermal plasma before deposition, well-crystallized BST films were deposited at substrate temperature of 630 °C. The dielectric constant and dielectric loss of the film at 100 kHz are 715 and 0.24, respectively. Due to the good crystallinity of the BST films deposited by MPE, high dielectric tunability up to 39.3% is achieved at low applied electric field of 100 kV cm-1.

MIST: An Open Source Environmental Modelling Programming Language Incorporating Easy to Use Data Parallelism.

NASA Astrophysics Data System (ADS)

Bellerby, Tim

2014-05-01

Model Integration System (MIST) is open-source environmental modelling programming language that directly incorporates data parallelism. The language is designed to enable straightforward programming structures, such as nested loops and conditional statements to be directly translated into sequences of whole-array (or more generally whole data-structure) operations. MIST thus enables the programmer to use well-understood constructs, directly relating to the mathematical structure of the model, without having to explicitly vectorize code or worry about details of parallelization. A range of common modelling operations are supported by dedicated language structures operating on cell neighbourhoods rather than individual cells (e.g.: the 3x3 local neighbourhood needed to implement an averaging image filter can be simply accessed from within a simple loop traversing all image pixels). This facility hides details of inter-process communication behind more mathematically relevant descriptions of model dynamics. The MIST automatic vectorization/parallelization process serves both to distribute work among available nodes and separately to control storage requirements for intermediate expressions - enabling operations on very large domains for which memory availability may be an issue. MIST is designed to facilitate efficient interpreter based implementations. A prototype open source interpreter is available, coded in standard FORTRAN 95, with tools to rapidly integrate existing FORTRAN 77 or 95 code libraries. The language is formally specified and thus not limited to FORTRAN implementation or to an interpreter-based approach. A MIST to FORTRAN compiler is under development and volunteers are sought to create an ANSI-C implementation. Parallel processing is currently implemented using OpenMP. However, parallelization code is fully modularised and could be replaced with implementations using other libraries. GPU implementation is potentially possible.

Remediation of Uranium in the Hanford Vadose Zone Using Gas-Transported Reactants: Laboratory Scale Experiments in Support of the Deep Vadose Zone Treatability Test Plan for the Hanford Central Plateau

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szecsody, James E.; Truex, Michael J.; Zhong, Lirong

2010-01-04

This laboratory-scale investigation is focused on decreasing mobility of uranium in subsurface contaminated sediments in the vadose zone by in situ geochemical manipulation at low water content. This geochemical manipulation of the sediment surface phases included reduction, pH change (acidic and alkaline), and additions of chemicals (phosphate, ferric iron) to form specific precipitates. Reactants were advected into 1-D columns packed with Hanford 200 area U-contaminated sediment as a reactive gas (for CO2, NH3, H2S, SO2), with a 0.1% water content mist (for NaOH, Fe(III), HCl, PO4) and with a 1% water content foam (for PO4). Uranium is present in themore » sediment in multiple phases that include (in decreasing mobility): aqueous U(VI) complexes, adsorbed U, reduced U(IV) precipitates, rind-carbonates, total carbonates, oxides, silicates, phosphates, and in vanadate minerals. Geochemical changes were evaluated in the ability to change the mixture of surface U phases to less mobile forms, as defined by a series of liquid extractions that dissolve progressively less soluble phases. Although liquid extractions provide some useful information as to the generalized uranium surface phases (and are considered operational definitions of extracted phases), positive identification (by x-ray diffraction, electron microprobe, other techniques) was also used to positively identify U phases and effects of treatment. Some of the changes in U mobility directly involve U phases, whereas other changes result in precipitate coatings on U surface phases. The long-term implication of the U surface phase changes to alter U mass mobility in the vadose zone was then investigated using simulations of 1-D infiltration and downward migration of six U phases to the water table. In terms of the short-term decrease in U mobility (in decreasing order), NH3, NaOH mist, CO2, HCl mist, and Fe(III) mist showed 20% to 35% change in U surface phases. Phosphate addition (mist or foam advected) showed inconsistent change in aqueous and adsorbed U, but significant coating (likely phosphates) on U-carbonates. The two reductive gas treatments (H2S and SO2) showed little change. For long-term decrease in U reduction, mineral phases created that had low solubility (phosphates, silicates) were desired, so NH3, phosphates (mist and foam delivered), and NaOH mist showed the greatest formation of these minerals. In addition, simulations showed the greatest decrease in U mass transport time to reach groundwater (and concentration) for these silicate/phosphate minerals. Advection of reactive gasses was the easiest to implement at the laboratory scale (and presumably field scale). Both mist and foam advection show promise and need further development, but current implementation move reactants shorter distances relative to reactive gasses. Overall, the ammonia and carbon dioxide gas had the greatest overall geochemical performance and ability to implement at field scale. Corresponding mist-delivered technologies (NaOH mist for ammonia and HCl mist for carbon dioxide) performed as well or better geochemically, but are not as easily upscaled. Phosphate delivery by mist was rated slightly higher than by foam delivery simply due to the complexity of foam injection and unknown effect of U mobility by the presence of the surfactant.« less

Biomass Production of Hairy Roots of Artemisia annua and Arachis hypogaea in a Scaled-Up Mist Bioreactor

PubMed Central

Sivakumar, Ganapathy; Liu, Chunzhao; Towler, Melissa J.

2014-01-01

Hairy roots have the potential to produce a variety of valuable small and large molecules. The mist reactor is a gas phase bioreactor that has shown promise for low-cost culture of hairy roots. Using a newer, disposable culture bag, mist reactor performance was studied with two species, Artemisia annua L. and Arachis hypogaea (peanut), at scales from 1 to 20 L. Both species of hairy roots when grown at 1 L in the mist reactor showed growth rates that surpassed that in shake flasks. From the information gleaned at 1 L, Arachis was scaled further to 4 and then 20 L. Misting duty cycle, culture medium flow rate, and timing of when flow rate was increased were varied. In a mist reactor increasing the misting cycle or increasing the medium flow rate are the two alternatives for increased delivery of liquid nutrients to the root bed. Longer misting cycles beyond 2–3 min were generally deemed detrimental to growth. On the other hand, increasing the medium flow rate to the sonic nozzle especially during the exponential phase of root growth (weeks 2–3) was the most important factor for increasing growth rates and biomass yields in the 20 L reactors. A. hypogaea growth in 1 L reactors was μ = 0.173 day−1 with biomass yield of 12.75 g DWL−1. This exceeded that in shake flasks at μ = 0.166 day−1 and 11.10 g DWL−1. Best growth rate and biomass yield at 20 L was μ = 0.147 and 7.77 g DWL−1, which was mainly achieved when medium flow rate delivery was increased. The mist deposition model was further evaluated using this newer reactor design and when the apparent thickness of roots (+hairs) was taken into account, the empirical data correlated with model predictions. Together these results establish the most important conditions to explore for future optimization of the mist bioreactor for culture of hairy roots. PMID:20687140

40 CFR 60.83 - Standard for acid mist.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 7 2014-07-01 2014-07-01 false Standard for acid mist. 60.83 Section 60.83 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Sulfuric Acid Plants § 60...

40 CFR 60.83 - Standard for acid mist.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standard for acid mist. 60.83 Section 60.83 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Sulfuric Acid Plants § 60...

40 CFR 62.1875 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of Sources: The plan includes the following sulfuric acid plants: (1) Allied Chemical Company... Mist from Existing Sulfuric Acid Plants § 62.1875 Identification of plan. (a) Title of plan: State implementation plan for control of sulfuric acid mist from existing sulfuric acid plants. (b) The plan was...

40 CFR 62.1875 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Sources: The plan includes the following sulfuric acid plants: (1) Allied Chemical Company... Mist from Existing Sulfuric Acid Plants § 62.1875 Identification of plan. (a) Title of plan: State implementation plan for control of sulfuric acid mist from existing sulfuric acid plants. (b) The plan was...

40 CFR 62.1875 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Sources: The plan includes the following sulfuric acid plants: (1) Allied Chemical Company... Mist from Existing Sulfuric Acid Plants § 62.1875 Identification of plan. (a) Title of plan: State implementation plan for control of sulfuric acid mist from existing sulfuric acid plants. (b) The plan was...

40 CFR 62.1875 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Sources: The plan includes the following sulfuric acid plants: (1) Allied Chemical Company... Mist from Existing Sulfuric Acid Plants § 62.1875 Identification of plan. (a) Title of plan: State implementation plan for control of sulfuric acid mist from existing sulfuric acid plants. (b) The plan was...

40 CFR 63.702 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... tape manufacturing are: y-oxide, doped iron oxides, chromium dioxide, barium ferrite, and metallic... uncombined water, that exists as liquid or solid particles such as dust, smoke, mist, or fumes at standard...

40 CFR 63.702 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... tape manufacturing are: y-oxide, doped iron oxides, chromium dioxide, barium ferrite, and metallic... uncombined water, that exists as liquid or solid particles such as dust, smoke, mist, or fumes at standard...

Heat Transfer and Observation of Droplet-Surface Interactions During Air-Mist Cooling at CSP Secondary System Temperatures

NASA Astrophysics Data System (ADS)

Huerta L., Mario E.; Mejía G., M. Esther; Castillejos E., A. Humberto

2016-04-01

Air-mists are key elements in the secondary cooling of modern thin steel slab continuous casters. The selection of water, W, and air, A, flow rates, and pressures in pneumatic nozzles open up a wide spectrum of cooling possibilities by their influence on droplet diameter, d, droplet velocity, v, and water impact flux, w. Nonetheless, due to the harsh environment resulting from the high temperatures and dense mists involved, there is very little information about the correlation between heat flux extracted, - q, and mist characteristics, and none about the dynamics of drop-wall interactions. For obtaining both kinds of information, this work combines a steady-state heat flux measuring method with a visualization technique based on a high-speed camera and a laser illumination system. For wall temperatures, T w, between ~723 K and ~1453 K (~450 °C and ~1180 °C), which correspond to film boiling regime, it was confirmed that - q increases with increase in v, w, and T w and with decrease in d. It should be noticed, however, that the increase in w generally decreases the spray cooling effectiveness because striking drops do not evaporate efficiently due to the interference by liquid remains from previous drops. Visualization of the events happening close to the surface also reveals that the contact time of the liquid with the surface is very brief and that rebounding, splashing, sliding, and levitation of drops lead to ineffective contact with the surface. At the center of the mist footprint, where drops impinge nearly normal to the surface those with enough momentum establish intimate contact with it before forming a vapor layer that pushes away the remaining liquid. Also, some drops are observed sliding upon the surface or levitating close to it; these are drops with low momentum which are influenced by the deflecting air stream. At footprint positions where oblique impingement occurs, frequently drops are spotted sliding or levitating and liquid films flowing in from inner positions are seen generating vapor cushions after having stayed in contact with the surface. Visualization of events taking place under high, ~500 kPa, and low, ~200 kPa, air nozzle pressure, p a, conditions suggests that the considerably larger heat extraction obtained under high p a is related to more frequent impingement of finer and faster drops that result in the formation of a dense fog of tiny secondary drops that moves tangentially close to the surface.

Development and Research on the Mechanism of Novel Mist Etching Method for Oxide Thin Films

NASA Astrophysics Data System (ADS)

Kawaharamura, Toshiyuki; Hirao, Takashi

2012-03-01

A novel etching process with etchant mist was developed and applied to oxide thin films such as zinc oxide (ZnO), zinc magnesium oxide (ZnMgO), and indium tin oxide (ITO). By using this process, it was shown that precise control of the etching characteristics is possible with a reasonable etching rate, for example, in the range of 10-100 nm/min, and a fine pattern of high accuracy can also be realized, even though this is usually very difficult by conventional wet etching processes, for ZnO and ZnMgO. The mist etching process was found to be similarly and successfully applied to ITO. The mechanism of mist etching has been studied by examining the etching temperature dependence of pattern accuracy, and it was shown that the mechanism was different from that of conventional liquid-phase spray etching. It was ascertained that fine pattern etching was attained using mist droplets completely (or partly) gasified by the heat applied to the substrate. This technique was applied to the fabrication of a ZnO thin-film transistor (TFT) with a ZnO active channel length of 4 µm. The electrical properties of the TFT were found to be excellent with fine uniformity over the entire 4-in. wafer.

RAPIDGRAB 2000™

EPA Pesticide Factsheets

Technical product bulletin: this miscellaneous oil spill control agent used in cleanups is a non-ionic liquid formulation applied by mist spraying onto floating oil slicks and sheens. Uses oleophitic synergistic effect of contraction and congealment.

Making Laser Beams Visible.

ERIC Educational Resources Information Center

Knotts, Michael

1993-01-01

Describes an inexpensive fog machine that is useful for photography and laser demonstrations. The apparatus uses liquid nitrogen to chill steam to make a fine mist safe for precision optics. The device can be made for around $50. (MVL)

Magnetic cellulose-derivative structures

DOEpatents

Walsh, M.A.; Morris, R.S.

1986-09-16

Structures to serve as selective magnetic sorbents are formed by dissolving a cellulose derivative such as cellulose triacetate in a solvent containing magnetic particles. The resulting solution is sprayed as a fine mist into a chamber containing a liquid coagulant such as n-hexane in which the cellulose derivative is insoluble but in which the coagulant is soluble or miscible. On contact with the coagulant, the mist forms free-flowing porous magnetic microspheric structures. These structures act as containers for the ion-selective or organic-selective sorption agent of choice. Some sorption agents can be incorporated during the manufacture of the structure. 3 figs.

Magnetic cellulose-derivative structures

DOEpatents

Walsh, Myles A.; Morris, Robert S.

1986-09-16

Structures to serve as selective magnetic sorbents are formed by dissolving a cellulose derivative such as cellulose triacetate in a solvent containing magnetic particles. The resulting solution is sprayed as a fine mist into a chamber containing a liquid coagulant such as n-hexane in which the cellulose derivative is insoluble but in which the coagulant is soluble or miscible. On contact with the coagulant, the mist forms free-flowing porous magnetic microspheric structures. These structures act as containers for the ion-selective or organic-selective sorption agent of choice. Some sorbtion agents can be incorporated during the manufacture of the structure.

Experimental observations of pressure oscillations and flow regimes in an analogue volcanic system

USGS Publications Warehouse

Lane, S.J.; Chouet, B.A.; Phillips, J.C.; Dawson, P.; Ryan, G.A.; Hurst, E.

2001-01-01

Gas-liquid flows, designed to be analogous to those in volcanic conduits, are generated in the laboratory using organic gas-gum rosin mixtures expanding in a vertically mounted tube. The expanding fluid shows a range of both flow and pressure oscillation behaviors. Weakly supersaturated source liquids produce a low Reynolds number flow with foam expanding from the top surface of a liquid that exhibits zero fluid velocity at the tube wall; i.e., the conventional "no-slip" boundary condition. Pressure oscillations, often with strong long-period characteristics and consistent with longitudinal and radial resonant oscillation modes, are detected in these fluids. Strongly supersaturated source liquids generate more energetic flows that display a number of flow regimes. These regimes include a static liquid source, viscous flow, detached flow (comprising gas-pockets-at-wall and foam-in-gas annular flow, therefore demonstrating strong radial heterogeneity), and a fully turbulent transonic fragmented or mist flow. Each of these flow regimes displays characteristic pressure oscillations that can be related to resonance of flow features or wall impact phenomena. The pressure oscillations are produced by the degassing processes without the need of elastic coupling to the confining medium or flow restrictors and valvelike features. The oscillatory behavior of the experimental flows is compared to seismoacoustic data from a range of volcanoes where resonant oscillation of the fluid within the conduit is also often invoked as controlling the observed oscillation frequencies. On the basis of the experimental data we postulate on the nature of seismic signals that may be measured during large-scale explosive activity. Copyright 2001 by the American Geophysical Union.

Radiation characteristics of water droplets in a fire-inspired environment: A Monte Carlo ray tracing study

NASA Astrophysics Data System (ADS)

Wu, Bifen; Zhao, Xinyu

2018-06-01

The effects of radiation of water mists in a fire-inspired environment are numerically investigated for different complexities of radiative media in a three-dimensional cubic enclosure. A Monte Carlo ray tracing (MCRT) method is employed to solve the radiative transfer equation (RTE). The anisotropic scattering behaviors of water mists are modeled by a combination of the Mie theory and the Henyey-Greestein relation. A tabulation method considering the size and wavelength dependencies is established for water droplets, to reduce the computational cost associated with the evaluation of the nongray spectral properties of water mists. Validation and verification of the coupled MCRT solver are performed using a one-dimensional slab with gray gas in comparison with the analytical solutions. Parametric studies are then performed using a three-dimensional cubic box to examine radiation of two monodispersed and one polydispersed water mist systems. The tabulation method can reduce the computational cost by a factor of one hundred. Results obtained without any scattering model better conform with results obtained from the anisotropic model than the isotropic scattering model, when a highly directional emissive source is applied. For isotropic emissive sources, isotropic and anisotropic scattering models predict comparable results. The addition of different volume fractions of soot shows that soot may have a negative impact on the effectiveness of water mists in absorbing radiation when its volume fraction exceeds certain threshold.

Test of phi(sup 2) model predictions near the (sup 3)He liquid-gas critical point

NASA Technical Reports Server (NTRS)

Barmatz, M.; Zhong, F.; Hahn, I.

2000-01-01

NASA is supporting the development of an experiment called MISTE (Microgravity Scaling Theory Experiment) for future International Space Station mission. The main objective of this flight experiment is to perform in-situ PVT, heat capacity at constant volume, C(sub v) and chi(sub tau), measurements in the asymptotic region near the (sup 3)He liquid-gas critical point.

[Analysis on Mechanism of Rainout Carried by Wet Stack of Thermal Power Plant].

PubMed

Ouyang, Li-hua; Zhuang, Ye; Liu, Ke-wei; Chen, Zhen-yu; Gu, Peng

2015-06-01

Rainout from wet-stack took placed in many thermal power plants with WFGD system. Research on causes of the rainout is important to solve the problem. The objective of this research is to analyze the mechanism of rainout. Field study was performed to collect experimental data in one thermal power plant, including the amount of desulfurization slurry carried by wet flue gas, liquor condensate from wet duct, and droplets from the wet stack. Source apportionment analysis was carried out based on physical and chemical data of liquid sample and solid sample. The result showed that mist eliminator operated well, which met the performance guarantee value. But the total amount of desulfurization slurry in flue gas and the sulfate concentration in liquid condensate discharge from the wet duct/stack increased. The liquid condensate accumulated in the wet duct/stack led to liquid re-entrainment. In conclusion, the rainout in this power plant was caused by the short of wet ductwork or liquid discharge system, the droplets caused by re-entrainment carried by the saturated gas released from the stack. The main undissolved components of the rainout were composite carbonate and aluminosilicate. Although ash concentration in this WFGD met the regulation criteria, source apportionment analysis showed that fly ash contributed to rainout was accounted for 60%. This percentage value was same as the data of solid particles in the condensate. It is important to optimize the wet ductwork, wet stack liner, liquid collectors and drainage. Avoiding the accumulation from saturated vapor thermal condensation is an effective way to solve the wet stack rainout.

40 CFR 63.1001 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the purposes of this subpart, means to take action for the purpose of stopping or reducing leakage of.... Liquids dripping means any visible leakage from the seal including dripping, spraying, misting, clouding... compounds based on a detection principle such as infra-red, photo ionization, or thermal conductivity...

40 CFR 62.9110 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.9110 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants. (1) National Zinc Co...] Fluoride Emissions From Phosphate Fertilizer Plants ...

40 CFR 62.9110 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.9110 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants. (1) National Zinc Co...] Fluoride Emissions From Phosphate Fertilizer Plants ...

The MIST /MIUS Integration and Subsystems Test/ laboratory - A testbed for the MIUS /Modular Integrated Utility System/ program

NASA Technical Reports Server (NTRS)

Beckham, W. S., Jr.; Keune, F. A.

1974-01-01

The MIUS (Modular Integrated Utility System) concept is to be an energy-conserving, economically feasible, integrated community utility system to provide five necessary services: electricity generation, space heating and air conditioning, solid waste processing, liquid waste processing, and residential water purification. The MIST (MIUS Integration and Subsystem Test) integrated system testbed constructed at the Johnson Space Center in Houston includes subsystems for power generation, heating, ventilation, and air conditioning (HVAC), wastewater management, solid waste management, and control and monitoring. The key design issues under study include thermal integration and distribution techniques, thermal storage, integration of subsystems controls and displays, incinerator performance, effluent characteristics, and odor control.

Minute gun series: Diana mist event. Project officers report (sanitized version). Summary report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schiff, A.T.; Tiano, D.E.

1971-12-27

Diana Mist was a Department of Defense underground nuclear test executed on 11 February 1970 in the n.06 drift of the U12n tunnel complex. Test chambers were located in an evacuated horizontal line-of-sight pipe at 400, 640, 755, 905, and 1110 feet from the nuclear source. The objectives of practically all other experiments were achieved through active measurements and/or posttest examination.

40 CFR 62.4900 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.4900 Identification of sources. The plan applies to the following existing sulfuric acid plants: (a) Delta Chemical in Searsport, Maine. [54 FR 22896, May...

40 CFR 62.4900 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.4900 Identification of sources. The plan applies to the following existing sulfuric acid plants: (a) Delta Chemical in Searsport, Maine. [54 FR 22896, May...

40 CFR 62.4900 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.4900 Identification of sources. The plan applies to the following existing sulfuric acid plants: (a) Delta Chemical in Searsport, Maine. [54 FR 22896, May...

40 CFR 62.4900 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.4900 Identification of sources. The plan applies to the following existing sulfuric acid plants: (a) Delta Chemical in Searsport, Maine. [54 FR 22896, May...

40 CFR 62.4900 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.4900 Identification of sources. The plan applies to the following existing sulfuric acid plants: (a) Delta Chemical in Searsport, Maine. [54 FR 22896, May...

Multimodal Information Sharing Team (MIST) - Port of Baltimore Industry and Public Sector Cooperation for Information Sharing

DTIC Science & Technology

2012-11-01

engage key stakeholders. For example, it was identified that the liquid bulk, private terminal operators, rail and trucking groups are not...implementation of their counterterrorism and public safety missions. 30 Maryland Natural Resources Police/Department of Natural Resources ( MNRP ) http

41 CFR 50-204.67 - Oxygen.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 41 Public Contracts and Property Management 1 2013-07-01 2013-07-01 false Oxygen. 50-204.67..., Vapors, Fumes, Dusts, and Mists § 50-204.67 Oxygen. The in-plant transfer, handling, storage, and utilization of oxygen as a liquid or a compressed gas shall be in accordance with Compressed Gas Association...

41 CFR 50-204.67 - Oxygen.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 41 Public Contracts and Property Management 1 2014-07-01 2014-07-01 false Oxygen. 50-204.67..., Vapors, Fumes, Dusts, and Mists § 50-204.67 Oxygen. The in-plant transfer, handling, storage, and utilization of oxygen as a liquid or a compressed gas shall be in accordance with Compressed Gas Association...

40 CFR 62.10860 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.10860 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants: (1) Diamond-Shamrock... Inc. in Deer Park, Texas. (6) Stauffer Chemical Company in Baytown, Texas. (7) Stauffer Chemical...

40 CFR 62.10860 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.10860 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants: (1) Diamond-Shamrock... Inc. in Deer Park, Texas. (6) Stauffer Chemical Company in Baytown, Texas. (7) Stauffer Chemical...

40 CFR 62.10860 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.10860 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants: (1) Diamond-Shamrock... Inc. in Deer Park, Texas. (6) Stauffer Chemical Company in Baytown, Texas. (7) Stauffer Chemical...

40 CFR 62.10860 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.10860 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants: (1) Diamond-Shamrock... Inc. in Deer Park, Texas. (6) Stauffer Chemical Company in Baytown, Texas. (7) Stauffer Chemical...

40 CFR 62.10860 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Acid Mist from Existing Sulfuric Acid Plants § 62.10860 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants: (1) Diamond-Shamrock... Inc. in Deer Park, Texas. (6) Stauffer Chemical Company in Baytown, Texas. (7) Stauffer Chemical...

Preparation of LiMn{sub 2}O{sub 4} cathode thin films for thin film lithium secondary batteries by a mist CVD process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tadanaga, Kiyoharu, E-mail: tadanaga@chem.osakafu-u.ac.jp; Yamaguchi, Akihiro; Sakuda, Atsushi

2014-05-01

Highlights: • LiMn{sub 2}O{sub 4} thin films were prepared by using the mist CVD process. • An aqueous solution of lithium and manganese acetates is used for the precursor solution. • The cell with the LiMn{sub 2}O{sub 4} thin films exhibited a capacity of about 80 mAh/g. • The cell showed good cycling performance during 10 cycles. - Abstract: LiMn{sub 2}O{sub 4} cathode thin films for thin film lithium secondary batteries were prepared by using so-called the “mist CVD process”, employing an aqueous solution of lithium acetate and manganese acetate, as the source of Li and Mn, respectively. The aqueousmore » solution of starting materials was ultrasonically atomized to form mist particles, and mists were transferred by nitrogen gas to silica glass substrate to form thin films. FE-SEM observation revealed that thin films obtained by this process were dense and smooth, and thin films with a thickness of about 750 nm were obtained. The electrochemical cell with the thin films obtained by sintering at 700 °C exhibited a capacity of about 80 mAh/g, and the cell showed good cycling performance during 10 cycles.« less

A Brief Assessment of LC2IEDM, MIST and Web Services for use in Naval Tactical Data Management

DTIC Science & Technology

2004-07-01

server software, messaging between the client and server, and a database. The MIST database is implemented in an open source DBMS named PostGreSQL ... PostGreSQL had its beginnings at the University of California, Berkley, in 1986 [11]. The development of PostGreSQL has since evolved into a...contact history from the database. DRDC Atlantic TM 2004-148 9 Request Software Request Software Server Side Response from service

Development of a wet vapor homogeneous liquid metal MHD power system

NASA Astrophysics Data System (ADS)

1989-04-01

During the period covered by this report (October 1988 to March 1989), the following work was done: the mixing stream condensation process was analyzed, and a theoretical model for simulating this process was modified. A parametric study is being conducted at the present time; the separation processes were analyzed; and the experimental system was specified and its design is at present in an advanced stage. The mixing stream condensation process was analyzed. For the parameters defined in the SOW of this project the process was found to be a mist flow direct contact condensation, where the hot gas mixture consisting of inert gas and vapor is the continuous phase, and the subcooled liquid on which the vapor is condensed if the droplets dispersed phase. Two possibilities of creating the mist flow were considered. The first, injecting the cold Liquid Metal (LM) into the Mixing Streams Condenser (MSC) entrance as a jet and breaking it into LM fragments and the fragments into droplets by momentum transfer breakup mechanism. The second, atomizing the cooled LM stream into little droplets (approximately 100 micrometers in diameter) and accelerating them by the gas. The second possibility was preferred due to its much higher heat and mass transfer surface and coefficients relative to the first one.

A Study of Flame Propagation on Water-Mist Laden Gas Mixtures in Microgravity

NASA Technical Reports Server (NTRS)

Abbud-Madrid, A.; Riedel, E. P.; McKinnon, J. T.

1999-01-01

The use of water mists (very fine water sprays) for fire suppression is currently receiving increased attention as a replacement technology for halogen-based chemical agents-such as Halon 1301 (CF3Br)--the manufacturing of which has been banned by the Montreal Protocol due to their high ozone depletion potential. Water mist technology has been found effective for a wide range of applications such as Class B pool fires, shipboard machinery, aircraft cabins, computers, and electronic equipment. There are five distinct mechanisms by which water droplets may interact with a flame. First, the high enthalpy of vaporization of water (2450 kJ/kg) leads to heat removal from the flame front as the liquid droplets turn to steam. Second, as water vaporizes its volume increases approximately three orders of magnitude, which leads to the dilution of the oxygen and vaporized fuel required to maintain the flame. The third effect is the recombination of H-atoms and other radicals on the droplet surface. A fourth effect of water mists in fires is the retardation of surface propagation rates due to the wetting of walls and surfaces. The last potential impact of fine water mists affects the radiative propagation of the fire by forming an optically thick barrier to infrared radiation which prevents ignition of the unburned regions. Unfortunately, little fundamental information exists on the interaction of a flame with a water mist. To date, there is no widely accepted interpretation of the critical concentration of droplets required to suppress a flame or of the fundamental mechanisms involved in flame extinguishment by water mists. One of the main obstacles to obtaining such understanding is the difficulty of providing a simple, well-defined experimental setup for the flame front/water mist interaction. Some of the difficulty stems from the problem of generating, distributing and maintaining a homogeneous concentration of droplets throughout a chamber while gravity depletes the concentration and alters the droplet size by coalescence and agglomeration mechanisms. Experiments conducted in the absence of gravity provide an ideal environment to study the interaction of water mists and flames by eliminating these distorting effects. In addition, microgravity eliminates the complex flow patterns induced between the flame front and the water droplets. The long duration and quality of microgravity in space flights provide the required conditions to perform the setup and monitoring of flame suppression experiments. Consequently, a series of experiments have been identified to be performed on the Combustion Module (CM-2) in the Space Shuttle. These consist of measuring the extinguishing capability of a water mist on a premixed flame propagating along a tube. These experiments should provide the necessary data to obtain further understanding of the water mist suppression phenomena that can be later used to design and manufacture appropriate fire suppression systems. In preparation for the orbital flights, experiments have been conducted on low-gravity ground facilities to obtain the preliminary data necessary to define the scientific objectives and technical issues of the spacecraft experiments.

41 CFR 50-204.67 - Oxygen.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 41 Public Contracts and Property Management 1 2012-07-01 2009-07-01 true Oxygen. 50-204.67 Section..., Vapors, Fumes, Dusts, and Mists § 50-204.67 Oxygen. The in-plant transfer, handling, storage, and utilization of oxygen as a liquid or a compressed gas shall be in accordance with Compressed Gas Association...

41 CFR 50-204.67 - Oxygen.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 41 Public Contracts and Property Management 1 2010-07-01 2010-07-01 true Oxygen. 50-204.67 Section..., Vapors, Fumes, Dusts, and Mists § 50-204.67 Oxygen. The in-plant transfer, handling, storage, and utilization of oxygen as a liquid or a compressed gas shall be in accordance with Compressed Gas Association...

41 CFR 50-204.67 - Oxygen.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 41 Public Contracts and Property Management 1 2011-07-01 2009-07-01 true Oxygen. 50-204.67 Section..., Vapors, Fumes, Dusts, and Mists § 50-204.67 Oxygen. The in-plant transfer, handling, storage, and utilization of oxygen as a liquid or a compressed gas shall be in accordance with Compressed Gas Association...

Revealing the physicochemical mechanism for ultrasonic separation of alcohol-water mixtures

NASA Astrophysics Data System (ADS)

Kirpalani, D. M.; Toll, F.

2002-08-01

The selective separation of ethanol from ethanol-water mixtures by ultrasonic atomization has been reported recently by Sato, Matsuura, and Fujii [J. Chem. Phys. 114, 2382 (2001)]. In that work, experimental data were reported that confirmed the generation of an ethanol-rich droplet mist and attempted to explain the selective separation in terms of parametric decay instability of the capillary wave formed during sonication. In the present work, an alternate mechanism based on the conjunction theory has been postulated for the process of ultrasonic atomization. This mechanism involves the formation of cavitating bubbles in the liquid during sonication and their eventual collapse at the liquid surface into a cloud of microbubbles that moves upwards in a capillary fountain jet. The selective separation of alcohols has been explained as a corollary effect of the physical mechanism resulting in a surface excess of alcohol molecules formed at the surface of the microbubbles. The alcohol molecules vaporize into the microbubbles and release an alcohol-rich mist on their collapse in regions of high accumulation of acoustic energy.

CAPSULE REPORT: HARD CHROME FUME ...

EPA Pesticide Factsheets

All existing information which includes the information extrapolated from the Hard Chrome Pollution Prevention Demonstration Project(s) and other sources derived from plating facilities and industry contacts, will be condensed and featured in this document. At least five chromium emission prevention/control devices have been tested covering a wide spectrum of techniques currently in use at small and large-sized chrome metal plating shops. The goal for limiting chromium emissions to levels specified in the MACT Standards are: (1) 0.030 milligrams per dry standard cubic meter of air (mg/dscm) for small facilities with existing tanks, (2) 0.015 mg/dscm for small facilities with new tanks or large facilities with existing or new tanks. It should be emphasized that chemical mist suppressants still have quality issues and work practices that need to be addressed when they are used. Some of the mist suppressants currently in use are: one-, two-, and three-stage mesh pad mist eliminators; composite mesh pad mist eliminators; packed-bed scrubbers and polyballs. This capsule report should, redominantly, emphasize pollution prevention techniques and include, but not be restricted to, the afore-mentioned devices. Information

40 CFR 62.9110 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.9110 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants. (1) National Zinc Co. in Bartlesville, Oklahoma. (2) Tulsa Chemical Co. in Tulsa, Oklahoma. [52 FR 3230, Feb. 3, 1987...

40 CFR 62.9110 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.9110 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants. (1) National Zinc Co. in Bartlesville, Oklahoma. (2) Tulsa Chemical Co. in Tulsa, Oklahoma. [52 FR 3230, Feb. 3, 1987...

40 CFR 62.9110 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.9110 Identification of sources. (a) Identification of sources. The plan includes the following sulfuric acid production plants. (1) National Zinc Co. in Bartlesville, Oklahoma. (2) Tulsa Chemical Co. in Tulsa, Oklahoma. [52 FR 3230, Feb. 3, 1987...

40 CFR 62.6110 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.6110 Identification of sources. The plan applies to existing plants at the following locations: Sulfur burning plant and oleum plant of Mississippi Chemical Corporation in Pascagoula. Fluoride Emissions From Phosphate Fertilizer Plants ...

40 CFR 62.6110 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.6110 Identification of sources. The plan applies to existing plants at the following locations: Sulfur burning plant and oleum plant of Mississippi Chemical Corporation in Pascagoula. Fluoride Emissions From Phosphate Fertilizer Plants ...

40 CFR 62.6110 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.6110 Identification of sources. The plan applies to existing plants at the following locations: Sulfur burning plant and oleum plant of Mississippi Chemical Corporation in Pascagoula. Fluoride Emissions From Phosphate Fertilizer Plants ...

40 CFR 62.6110 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.6110 Identification of sources. The plan applies to existing plants at the following locations: Sulfur burning plant and oleum plant of Mississippi Chemical Corporation in Pascagoula. Fluoride Emissions From Phosphate Fertilizer Plants ...

40 CFR 62.6110 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.6110 Identification of sources. The plan applies to existing plants at the following locations: Sulfur burning plant and oleum plant of Mississippi Chemical Corporation in Pascagoula. Fluoride Emissions From Phosphate Fertilizer Plants ...

Validation of CTF Droplet Entrainment and Annular/Mist Closure Models using Riso Steam/Water Experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wysocki, Aaron J.; Salko, Robert K.

This report summarizes the work done to validate the droplet entrainment and de-entrainment models as well as two-phase closure models in the CTF code by comparison with experimental data obtained at Riso National Laboratory. The Riso data included a series of over 250 steam/water experiments that were performed in both tube and annulus geometries over a range of various pressures and outlet qualities. Experimental conditions were set so that the majority of cases were in the annular/mist ow regime. Measurements included liquid lm ow rate, droplet ow rate, lm thickness, and two-phase pressure drop. CTF was used to model 180more » of the tubular geometry cases, matching experimental geometry, outlet pressure, and outlet ow quality to experimental values. CTF results were compared to the experimental data at the outlet of the test section in terms of vapor and entrained liquid ow fractions, pressure drop per unit length, and liquid lm thickness. The entire process of generating CTF input decks, running cases, extracting data, and generating comparison plots was scripted using Python and Matplotlib for a completely automated validation process. All test cases and scripting tools have been committed to the COBRA-TF master repository and selected cases have been added to the continuous testing system to serve as regression tests. The dierences between the CTF- and experimentally-calculated ow fraction values were con- sistent with previous calculations by Wurtz, who applied the same entrainment correlation to the same data. It has been found that CTF's entrainment/de-entrainment predictive capability in the annular/mist ow regime for this particular facility is comparable to the licensed industry code, COBRAG. While lm and droplet predictions are generally good, it has been found that accuracy is diminished at lower ow qualities. This nding is consistent with the noted deciencies in the Wurtz entrainment model employed by CTF. The CTF predicted two-phase pressure drop in the annular/mist ow regime has been found to be highly inaccurate, exhibiting a clear bias with respect to the experimental data. This inaccuracy led to an investigation that revealed deciencies in the implementation of the annular/mist interfacial friction model, which should be investigated further in the future. Looking to published COBRAG results for this same facility reveal it exhibits no bias with regard to experimental pressure drop results. In addition to the problems with pressure drop prediction, the lm thickness was also signicantly under-predicted by CTF compared to both experimental data and Wurtz's analytical calculations. Film thickness is calculated using a simple geometric relationship and lm void fraction in CTF, which is dependent on slip ratio and interfacial friction. It is possible that the issues aecting the pressure drop and lm void prediction are related.« less

40 CFR 63.5935 - What definitions apply to this subpart?

Code of Federal Regulations, 2011 CFR

2011-07-01

... defined in the CAA, in 40 CFR 63.2, and in this section as follows: Atomized mechanical application means application of resin or gel coat with spray equipment that separates the liquid into a fine mist. This fine... equivalent material) prior to resin application, and the resin is injected into the covered mold are also...

40 CFR 62.3851 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Acid Mist from Existing Sulfuric Acid Production Plants § 62.3851 Identification of sources. (a) The plan applies to existing facilities at the following sulfuric acid production plants: (1) Agrico Chemical Company, Fort Madison, Iowa (2) Koch Sulfur Products Company, Dubuque, Iowa Fluoride Emissions...

40 CFR 62.3851 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Acid Mist from Existing Sulfuric Acid Production Plants § 62.3851 Identification of sources. (a) The plan applies to existing facilities at the following sulfuric acid production plants: (1) Agrico Chemical Company, Fort Madison, Iowa (2) Koch Sulfur Products Company, Dubuque, Iowa Fluoride Emissions...

40 CFR 62.3851 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Acid Mist from Existing Sulfuric Acid Production Plants § 62.3851 Identification of sources. (a) The plan applies to existing facilities at the following sulfuric acid production plants: (1) Agrico Chemical Company, Fort Madison, Iowa (2) Koch Sulfur Products Company, Dubuque, Iowa Fluoride Emissions...

40 CFR 62.3851 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Acid Mist from Existing Sulfuric Acid Production Plants § 62.3851 Identification of sources. (a) The plan applies to existing facilities at the following sulfuric acid production plants: (1) Agrico Chemical Company, Fort Madison, Iowa (2) Koch Sulfur Products Company, Dubuque, Iowa Fluoride Emissions...

40 CFR 62.3851 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Acid Mist from Existing Sulfuric Acid Production Plants § 62.3851 Identification of sources. (a) The plan applies to existing facilities at the following sulfuric acid production plants: (1) Agrico Chemical Company, Fort Madison, Iowa (2) Koch Sulfur Products Company, Dubuque, Iowa Fluoride Emissions...

Environmentally Safer, Less Toxic Fire-Extinguishing Agents

NASA Technical Reports Server (NTRS)

Parrish, Clyde F.

2003-01-01

Fire-extinguishing agents comprising microscopic drops of water microencapsulated in flame-retardant polymers have been proposed as effective, less toxic, non-ozone-depleting, non-globalwarming alternatives to prior fire-extinguishing agents. Among the prior fire-extinguishing agents are halons (various halocarbon fluids), which are toxic and contribute both to depletion of upperatmospheric ozone and to global warming. Other prior fire-extinguishing agents are less toxic and less environmentally harmful but, in comparison with halons, are significantly less effective in extinguishing fires. The proposal to formulate new waterbased agents is based on recent success in the use of water mist as a fire-suppression agent. Water suppresses a flame by reducing the flame temperature and the concentration of oxygen available for the combustion process. The temperature is reduced because the water droplets in the mist absorb latent heat of vaporization as they evaporate. The concentration of oxygen is reduced because the newly generated water vapor displaces air. Unfortunately, water mists are difficult to produce in confined spaces and can evaporate before they reach the bases of flames. The proposal addresses both of these issues: The proposed fire-extinguishing agents would be manufactured in microencapsulated form in advance, eliminating the problem of generating mists in confined spaces. Because of the microencapsulation, the droplets would not evaporate until exposed directly to the heat of flames. In addition, the proposal calls for the introduction of free radicals that would inhibit the propagation of the chemical reactions of the combustion reactions. Manufacturing of a fire-extinguishing agent according to the proposal would begin with the formulation of a suitable polymer (e.g., a polybromostyrene) that would contribute free radicals to the combustion process. The polymer would be dissolved in a suitable hydrocarbon liquid (e.g., toluene). Water would be dispersed in the polymer/toluene solution, then another hydrocarbon liquid (e.g., hexane) that is not a solvent for the polymer would be added to the mixture to make the dissolved polymer precipitate onto the water droplets. The resulting polymer-coated droplets would be removed from the coating mixture by filtration, dried, and stored for use.

In situ x-ray diffraction measurements of the capillary fountain jet produced via ultrasonic atomization.

PubMed

Yano, Yohko F; Douguchi, Junya; Kumagai, Atsushi; Iijima, Takao; Tomida, Yukinobu; Miyamoto, Toshiaki; Matsuura, Kazuo

2006-11-07

In situ x-ray diffraction measurements were carried out for investigating the liquid structure in the ultrasonic fountain jet to consider the mechanism of the "ultrasonic ethanol separation" reported by Sato et al. [J. Chem. Phys. 114, 2382 (2001)]. For pure liquids (water and ethanol), it was found that the high frequency ultrasound does not affect the liquid structure microscopically. For the 20 mol % ethanol-water mixture, the estimated ethanol mole fraction in the ultrasonic fountain jet by using the position of the main maximum in the x-ray diffraction profile coincided with that in the reservoir. This result suggests that the ethanol separation is not caused by any distorted liquid structure under the ultrasound irradiation and occurs when or after the generation of the liquid droplet mist.

In situ x-ray diffraction measurements of the capillary fountain jet produced via ultrasonic atomization

NASA Astrophysics Data System (ADS)

Yano, Yohko F.; Douguchi, Junya; Kumagai, Atsushi; Iijima, Takao; Tomida, Yukinobu; Miyamoto, Toshiaki; Matsuura, Kazuo

2006-11-01

In situ x-ray diffraction measurements were carried out for investigating the liquid structure in the ultrasonic fountain jet to consider the mechanism of the "ultrasonic ethanol separation" reported by Sato et al. [J. Chem. Phys. 114, 2382 (2001)]. For pure liquids (water and ethanol), it was found that the high frequency ultrasound does not affect the liquid structure microscopically. For the 20mol% ethanol-water mixture, the estimated ethanol mole fraction in the ultrasonic fountain jet by using the position of the main maximum in the x-ray diffraction profile coincided with that in the reservoir. This result suggests that the ethanol separation is not caused by any distorted liquid structure under the ultrasound irradiation and occurs when or after the generation of the liquid droplet mist.

40 CFR 62.1102 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Production Units § 62.1102 Identification of sources. The plan applies to existing facilities at the following sulfuric acid production units: (a... Chemical Company in Fresno County. (d) Stauffer Chemical Company in Alameda County. (e) Valley Nitrogen...

Liquid-Spray Formulation Of Scopolamine

NASA Technical Reports Server (NTRS)

Putcha, Lakshmi; Cintron, Nitza M.

1992-01-01

Scopolamine, fast-acting anticholinergic drug, formulated into drops administered intranasally. Formulation very useful for people who need immediate relief from motion sickness, and they can administer it to themselves. Also used in other clinical situations in which fast-acting anticholinergic medication required. Modified into such other forms as gel preparation, aqueous-base ointment, or aerosol spray or mist; also dispensed in metered-dose delivery system.

40 CFR 62.8351 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (5) Northeast Chemical Company in New Hanover County. (b) There are no oleum plants. (c) There are no... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.8351 Identification of sources. The plan applies to existing facilities at the following sulfuric acid plants: (a) Sulfur-burning plants operated by...

40 CFR 62.855 - Identification of sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Plants § 62.855 Identification of sources. (a) The plan applies to existing facilities at the following existing sulfuric acid plant: (1) El Dorado Chemical Company in El Dorado, Arkansas. (2) [Reserved] (b) [Reserved] [63 FR 11608, Mar. 10, 1998] Total...

40 CFR 62.855 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Plants § 62.855 Identification of sources. (a) The plan applies to existing facilities at the following existing sulfuric acid plant: (1) El Dorado Chemical Company in El Dorado, Arkansas. (2) [Reserved] (b) [Reserved] [63 FR 11608, Mar. 10, 1998] Total...

40 CFR 62.8351 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (5) Northeast Chemical Company in New Hanover County. (b) There are no oleum plants. (c) There are no... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.8351 Identification of sources. The plan applies to existing facilities at the following sulfuric acid plants: (a) Sulfur-burning plants operated by...

40 CFR 62.8351 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (5) Northeast Chemical Company in New Hanover County. (b) There are no oleum plants. (c) There are no... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.8351 Identification of sources. The plan applies to existing facilities at the following sulfuric acid plants: (a) Sulfur-burning plants operated by...

40 CFR 62.8351 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (5) Northeast Chemical Company in New Hanover County. (b) There are no oleum plants. (c) There are no... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.8351 Identification of sources. The plan applies to existing facilities at the following sulfuric acid plants: (a) Sulfur-burning plants operated by...

40 CFR 62.855 - Identification of sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Plants § 62.855 Identification of sources. (a) The plan applies to existing facilities at the following existing sulfuric acid plant: (1) El Dorado Chemical Company in El Dorado, Arkansas. (2) [Reserved] (b) [Reserved] [63 FR 11608, Mar. 10, 1998] Total...

40 CFR 62.855 - Identification of sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Plants § 62.855 Identification of sources. (a) The plan applies to existing facilities at the following existing sulfuric acid plant: (1) El Dorado Chemical Company in El Dorado, Arkansas. (2) [Reserved] (b) [Reserved] [63 FR 11608, Mar. 10, 1998] Total...

40 CFR 62.8351 - Identification of sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (5) Northeast Chemical Company in New Hanover County. (b) There are no oleum plants. (c) There are no... Sulfuric Acid Mist from Existing Sulfuric Acid Plants § 62.8351 Identification of sources. The plan applies to existing facilities at the following sulfuric acid plants: (a) Sulfur-burning plants operated by...

40 CFR 62.855 - Identification of sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Sulfuric Acid Mist Emissions from Existing Sulfuric Acid Plants § 62.855 Identification of sources. (a) The plan applies to existing facilities at the following existing sulfuric acid plant: (1) El Dorado Chemical Company in El Dorado, Arkansas. (2) [Reserved] (b) [Reserved] [63 FR 11608, Mar. 10, 1998] Total...

Experimental Study of the Effect of Water Mist Location On Blast Overpressure Attenuation in A Shock Tube

NASA Astrophysics Data System (ADS)

Mataradze, Edgar; Chikhradze, Nikoloz; Bochorishvili, Nika; Akhvlediani, Irakli; Tatishvili, Dimitri

2017-12-01

Explosion protection technologies are based on the formation of a shock wave mitigation barrier between the protection site and the explosion site. Contemporary protective systems use water mist as an extinguishing barrier. To achieve high effectiveness of the protective system, proper selection of water mist characteristics is important. The main factors defining shock wave attenuation in water mist include droplet size distribution, water concentration in the mist, droplet velocity and geometric properties of mist. This paper examines the process of attenuation of shock waves in mist with droplets ranging from 25 to 400 microns under different conditions of water mist location. Experiments were conducted at the Mining Institute with the use of a shock tube to study the processes of explosion suppression by a water mist barrier. The shock tube consists of a blast chamber, a tube, a system for the dosed supply of water, sensors, data recording equipment, and a process control module. Shock wave overpressure reduction coefficient was studied in the shock tube under two different locations of water mist: a) when water mist is created in direct contact with blast chamber and b) the blast chamber and the mist are separated by air space. It is established that in conditions when the air space distance between the blast chamber and the mist is 1 meter, overpressure reduction coefficient is 1.5-1.6 times higher than in conditions when water mist is created in direct contact with blast chamber.

Instrumentation, control and data management for the MIST (Modular Integrated Utility System) Facility

NASA Technical Reports Server (NTRS)

Celino, V. A.

1977-01-01

An appendix providing the technical data required for computerized control and/or monitoring of selected MIST subsystems is presented. Specific computerized functions to be performed are as follows: (1) Control of the MIST heating load simulator and monitoring of the diesel engine generators' cooling system; (2) Control of the MIST heating load simulator and MIST heating subsystem including the heating load simulator; and (3) Control of the MIST air conditioning load simulator subsystem and the MIST air conditioning subsystem, including cold thermal storage and condenser water flows.

Effects of water nanodroplets on skin moisture and viscoelasticity during air-conditioning.

PubMed

Ohno, Hideo; Nishimura, Naoki; Yamada, Kuniyuki; Shimizu, Yuuki; Iwase, Satoshi; Sugenoya, Junichi; Sato, Motohiko

2013-11-01

In air-conditioned rooms, dry air exacerbates some skin diseases, for example, senile xerosis, atopic dermatitis, and surface roughness. Humidifiers are used to improve air dryness, which often induces excess humidity and thermal discomfort. To address this issue, we investigated the effects of water nanodroplets (mist) on skin hydration, which may increase skin hydration by penetrating into the interstitial spaces between corneocytes of the stratum corneum (SC) without increasing air humidity. We examined biophysical parameters, including skin conductance and transepidermal water loss (TEWL), and biomechanical parameters of skin distension/retraction before and after suction at the forehead, lateral canthus, and cheek, with or without mist, in a testing environment (24°C, 35% relative humidity) for 120 min. In the group without mist, TEWL values significantly decreased at all the sites after 1 h compared with the initial values. However, in the presence of mist, TEWL values were maintained at the initial values through the test, yielding significant differences vs. the group without mist. There were no significant differences between mist and mist-free groups in terms of skin conductance. Skin distension was significantly increased in the group with mist compared with that in the group without mist at the forehead and cheek, suggesting a softening effect of mist. Skin deformation of the face was improved by mist, suggesting hydration of the SC by mist. The change in TEWL was influenced by mist, suggesting supply of water to the skin, particularly the SC, by mist. These data indicated that a mist of water nanodroplets played an important role in softening skin in an air-conditioned room without increasing excess humidity. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Antimisting fuel breakup and flammability

NASA Technical Reports Server (NTRS)

Parikh, P.; Fleeter, R.; Sarohia, V.

1983-01-01

The breakup behavior and flammability of antimisting turbine fuels subjected to aerodynamic shear are investigated. Fuels tested were Jet A containing 0.3% FM-9 polymer at various levels of degradation ranging from virgin AMK to neat Jet A. The misting behavior of the fuels was quantified by droplet size distribution measurements. A technique based on high resolution laser photography and digital image processing of photographic records for rapid determination of droplet size distribution was developed. The flammability of flowing droplet-air mixtures was quantified by direct measurements of temperature rise in a flame established in the wake of a continuous ignition source. The temperature rise measurements were correlated with droplet size measurements. The flame anchoring phenomenon associated with the breakup of a liquid fuel in the wake of bluff body was shown to be important in the context of a survivable crash scenario. A pass/fail criterion for flammability testing of antimisting fuels, based on this flame-anchoring phenomenon, was proposed. The role of various ignition sources and their intensity in ignition and post-ignition behavior of antimisting fuels was also investigated.

Multiloop integral system test (MIST): Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gloudemans, J.R.

1991-04-01

The Multiloop Integral System Test (MIST) is part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox designed plants. MIST is sponsored by the US Nuclear Regulatory Commission, the Babcock Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral facilities to address the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility --more » the Once Through Integral System (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST program is reported in 11 volumes. Volumes 2 through 8 pertain to groups of Phase 3 tests by type; Volume 9 presents inter-group comparisons; Volume 10 provides comparisons between the RELAP5/MOD2 calculations and MIST observations, and Volume 11 (with addendum) presents the later Phase 4 tests. This is Volume 1 of the MIST final report, a summary of the entire MIST program. Major topics include, Test Advisory Group (TAG) issues, facility scaling and design, test matrix, observations, comparison of RELAP5 calculations to MIST observations, and MIST versus the TAG issues. MIST generated consistent integral-system data covering a wide range of transient interactions. MIST provided insight into integral system behavior and assisted the code effort. The MIST observations addressed each of the TAG issues. 11 refs., 29 figs., 9 tabs.« less

A Novel Effect of Scattered-Light Interference in Misted Mirrors

ERIC Educational Resources Information Center

Bridge, N. James

2005-01-01

Interference rings can be observed in mirrors clouded by condensation, even in diffuse lighting. The effect depends on individual droplets acting as point sources by refracting light into the mirror, so producing coherent wave-trains which are reflected and then scattered again by diffraction round the same source droplet. The secondary wave-train…

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Boyle, D. P.; Bell, R. E.; Kaita, R.; Lucia, M.; Schmitt, J. C.; Scotti, F.; Kubota, S.; Hansen, C.; Biewer, T. M.; Gray, T. K.

2016-10-01

The Lithium Tokamak Experiment (LTX) is a modest-sized spherical tokamak with all-metal plasma facing components (PFCs), uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma. This work presents measurements of core plasma impurity concentrations and transport in LTX. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with 2 - 4 % Li, 0.6 - 2 % C, 0.4 - 0.7 % O, and Zeff < 1.2 . Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, and neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two. However, time-independent simulations with MIST indicated that neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles. Progress on additional analysis, including time-dependent impurity transport simulations and impurity measurements with liquid lithium coatings, and plans for diagnostic upgrades and future experiments in LTX- β will also be presented. This work supported by US DOE contracts DE-AC02-09CH11466 and DE-AC05-00OR22725.

Liquid-surface entrainment induced by shocked air stream

NASA Astrophysics Data System (ADS)

Rodriguez, V.; Jourdan, G.; Marty, A.; Allou, A.; Parisse, J.-D.

2018-02-01

Recently, we experimentally studied, in a shock tube environment, shock waves propagating over horizontal free water layers having depths of 10, 20, and 30 mm for shock wave Mach numbers M_is equal to 1.1 and 1.4. The qualitative interaction process was observed by means of high-speed visualizations, and the pressures arising in the air and in the water layer were measured and interpreted in terms of the various incident and refracted shock waves in air and water; in particular, it was concluded that the compression wave in the water is driven by the planar shock wave in the air. Additional experiments have been conducted and the novel contributions of the present technical note are quantitative results regarding the liquid-surface entrainment. At low Mach number (M_is=1.1 ), we show that the velocity of the droplets ejected into the air is independent of the water depth, unlike the wavelength of initial ripples and the angle of ejection. When the shock wave strength increases (M_is=1.4 ), the dispersion of a very thin droplet mist and a single large wave take place. We show that the thickening of the water mist and the velocity of the subsequent large wave decreases with the water-layer depth.

MIST final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gloudemans, J.R.

1991-08-01

The multiloop integral system test (MIST) was part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock Wilcox-designed plants. MIST was sponsored by the US Nuclear Regulatory Commission, the Babcock Wilcox Owners Group, the Electric Power Research Institute, and Babcock Wilcox. The unique features of the Babcock Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral system facilities to addresss the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility -- the once-through integralmore » system (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST program is reported in eleven volumes; Volumes 2 through 8 pertain to groups of Phase 3 tests by type, Volume 9 presents inter-group comparisons. Volume 10 provides comparisons between the RELAP5 MOD2 calculations and MIST observations, and Volume 11 (with addendum) presents the later, Phase 4 tests. This is Volume 1 of the MIST final report, a summary of the entire MIST program. Major topics include: test advisory grop (TAG) issues; facility scaling and design; test matrix; observations; comparisons of RELAP5 calculations to MIST observations; and MIST versus the TAG issues. 11 refs., 29 figs., 9 tabs.« less

Acid mist and ozone effects on the leaf chemistry of two western conifer species

NASA Technical Reports Server (NTRS)

Westman, Walter E.; Temple, Patrick J.

1989-01-01

The effects of ozone and acid-mist exposures on the leaf chemistry of Jeffrey pine and giant sequoia seedlings grown in filtered-air greenhouses were investigated. Acid-mist treatments (pH 4.1, 3.4, 2.7, or 2.0) were administered for 3 h, and ozone exposures (0, 0.10, and 0.20 microliter/liter), which followed acid-mist treatments, for 4 h, each for three days a week for six to nine weeks. It was found that seedlings were more susceptible to acid-mist and acid mist/ozone combinations, than to ozone alone. Acid mist treatment resulted in higher levels of nitrogen and sulfur (both present in acid mist) as well as Na. Leaves of giant sequoia exhibited increased K and decreased Mn, while Jeffrey pine showed increases in Fe and Mn. In sequoia leaves, concentrations of Ca, Mg, and Ba decreased. Acid treatment also reduced chlorophyll b concentrations in both conifer species. Extensive changes induced by acid mist are consistent with earlier observations of changes in spectral reflectance of conifer seedlings observed after three weeks of fumigation.

High air volume to low liquid volume aerosol collector

DOEpatents

Masquelier, Donald A.; Milanovich, Fred P.; Willeke, Klaus

2003-01-01

A high air volume to low liquid volume aerosol collector. A high volume flow of aerosol particles is drawn into an annular, centripetal slot in a collector which directs the aerosol flow into a small volume of liquid pool contained is a lower center section of the collector. The annular jet of air impinges into the liquid, imbedding initially airborne particles in the liquid. The liquid in the pool continuously circulates in the lower section of the collector by moving to the center line, then upwardly, and through assistance by a rotating deflector plate passes back into the liquid at the outer area adjacent the impinging air jet which passes upwardly through the liquid pool and through a hollow center of the collector, and is discharged via a side outlet opening. Any liquid droplets escaping with the effluent air are captured by a rotating mist eliminator and moved back toward the liquid pool. The collector includes a sensor assembly for determining, controlling, and maintaining the level of the liquid pool, and includes a lower centrally located valve assembly connected to a liquid reservoir and to an analyzer for analyzing the particles which are impinged into the liquid pool.

The difference of detecting water mist and smoke by electromagnetic wave in simulation experiments

NASA Astrophysics Data System (ADS)

Zhang, Jingdi; Cui, Bing; Xiao, Si

2015-10-01

Although mist is similar to smoke in morphology, their compositions are very different. Therefore there is a significant difference between mist and smoke when detected by electromagnetic wave. This paper puts forward a kind of feasible solution based on Ansoft HFSS software about how to determine the forest fire by distinguishing mist and smoke above the forest. The experiments simulate the difference between mist and smoke model when detected by electromagnetic wave in different wavelengths. We find the mist and smoke model cannot absorb or reflect electromagnetic wave efficiently in Megahertz band. While in Gigahertz band mist model began to absorb and reflect electromagnetic wave above 650 Gigahertz band, but no change in smoke model. And the biggest difference appears in Terahertz band.

Influence of water mist on propagation and suppression of laminar premixed flame

NASA Astrophysics Data System (ADS)

Belyakov, Nikolay S.; Babushok, Valeri I.; Minaev, Sergei S.

2018-03-01

The combustion of premixed gas mixtures containing micro droplets of water was studied using one-dimensional approximation. The dependencies of the burning velocity and flammability limits on the initial conditions and on the properties of liquid droplets were analyzed. Effects of droplet size and concentration of added liquid were studied. It was demonstrated that the droplets with smaller diameters are more effective in reducing the flame velocity. For droplets vaporizing in the reaction zone, the burning velocity is independent of droplet size, and it depends only on the concentration of added liquid. With further increase of the droplet diameter the droplets are passing through the reaction zone with completion of vaporization in the combustion products. It was demonstrated that for droplets above a certain size there are two stable stationary modes of flame propagation with transition of hysteresis type. The critical conditions of the transition are due to the appearance of the temperature maximum at the flame front and the temperature gradient with heat losses from the reaction zone to the products, as a result of droplet vaporization passing through the reaction zone. The critical conditions are similar to the critical conditions of the classical flammability limits of flame with the thermal mechanism of flame propagation. The maximum decrease in the burning velocity and decrease in the combustion temperature at the critical turning point corresponds to predictions of the classical theories of flammability limits of Zel'dovich and Spalding. The stability analysis of stationary modes of flame propagation in the presence of water mist showed the lack of oscillatory processes in the frames of the assumed model.

Soap films burst like flapping flags.

PubMed

Lhuissier, Henri; Villermaux, Emmanuel

2009-07-31

When punctured, a flat soap film bursts by opening a hole driven by liquid surface tension. The hole rim does not, however, remain smooth but soon develops indentations at the tip of which ligaments form, ultimately breaking and leaving the initially connex film into a mist of disjointed drops. We report on original observations showing that these indentations result from a flaglike instability between the film and the surrounding atmosphere inducing an oscillatory motion out of its plane. Just like a flag edge flaps in the wind, the film is successively accelerated on both sides perpendicularly to its plane, inducing film thickness modulations and centrifuging liquid ligaments that finally pinch off to form the observed spray. This effect exemplifies how the dynamics of fragile objects such as thin liquid films is sensitive to their embedding medium.

Development of the International Space Station (ISS) Fine Water Mist (FWM) Portable Fire Extinguisher

NASA Technical Reports Server (NTRS)

Rodriquez, Branelle; Graf, John; Carlile, Christie; Young, GIna

2012-01-01

The National Aeronautics and Space Administration (NASA) is developing a Fine Water Mist (FWM) Portable Fire Extinguisher (PFE) for use on the International Space Station (ISS). The ISS presently uses two different types of fire extinguishers: a water foam extinguisher in the Russian Segment, and a carbon dioxide extinguisher in the United States Orbital Segments, which include Columbus and Kibo pressurized elements. Currently, there are operational concerns with the emergency breathing equipment and the carbon dioxide extinguisher. The toxicity of the carbon dioxide requires the crew members to have an oxygen supply present during a fire event, therefore inherently creating an unsafe environment. The FWM PFE extinguishes a fire without creating a hazardous breathing environment for crew members. The following paper will discuss the unique functional and performance requirements that have been levied on the FWM PFE, identify unique microgravity design considerations for liquid and gas systems, as well as discuss the NASA ISS specific fire standards that were developed to establish an acceptable portable fire extinguisher s performance.

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Silica mist test for dust, fume, and mist respirators; minimum requirements. 84.1147 Section 84.1147 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Silica mist test for dust, fume, and mist respirators; minimum requirements. 84.1147 Section 84.1147 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Silica mist test for dust, fume, and mist respirators; minimum requirements. 84.1147 Section 84.1147 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Silica mist test for dust, fume, and mist respirators; minimum requirements. 84.1147 Section 84.1147 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1147 - Silica mist test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Silica mist test for dust, fume, and mist respirators; minimum requirements. 84.1147 Section 84.1147 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

Suppression of polymethyl methacrylate dust explosion by ultrafine water mist/additives.

PubMed

Gan, Bo; Li, Bei; Jiang, Haipeng; Bi, Mingshu; Gao, Wei

2018-06-05

The suppressions of ultrafine water mists containing additives (NaCl and NaHCO 3 ) on 100 nm, 5 μm, and 30 μm polymethyl methacrylate (PMMA) dust explosions were experimentally studied in a dust-explosion apparatus. High-speed photography showed that maximum vertical positions and flame propagation velocities were significantly decreased by suppression with ultrafine water mist/additives. Flame propagation velocities in 100 nm, 5 μm, and 30 μm dust explosions suppressed by the ultrafine pure water mist were reduced by 48.2%, 27.7%, and 15.3%, respectively. Maximum temperatures and temperature rising rates measured by a fine thermocouple in nano- and micro-PMMA dust explosions were also significantly decreased. It was proved that the addition of NaCl and NaHCO 3 improved the suppression effects of the ultrafine pure water mist. The improvement of explosion suppression by an 8% NaHCO 3 mist was superior to that of a 16% NaCl mist. The suppression mechanisms of ultrafine water mist/additives are further discussed by analyzing the physical and chemical effects. Copyright © 2018 Elsevier B.V. All rights reserved.

Suppression of agglomeration in fluidized bed coating. II. Measurement of mist size in a fluidized bed chamber and effect of sodium chloride addition on mist size.

PubMed

Yuasa, H; Nakano, T; Kanaya, Y

1999-02-01

It has been reported that the degree of particle agglomeration in fluidized bed coating is greatly affected by the spray mist size of coating solution. However, the mist size has generally been measured in open air, and few reports have described the measurement of the mist size in a chamber of the fluidized bed, in which actual coating is carried out. Therefore, using hydroxypropylmethyl cellulose (HPMC) aqueous solution as a coating solution, the spray mist size of the coating solution in a chamber of the fluidized bed was measured under various coating conditions, such as the distance from the spray nozzle, fluidization air volume, inlet air temperature and addition of sodium chloride (NaCl) into the coating solution. The mist size in the fluidized bed was compared with that in open air at various distances from the spray nozzle. Further, the relationship between the spray mist size and the degree of suppression of agglomeration at various NaCl concentrations during fluidized bed coating was studied. The mist size distribution showed a logarithmic normal distribution in both cases of the fluidized bed and open air. The number-basis median diameter of spray mist (D50) in the fluidized bed was smaller compared with that in open air. D50 increased with the increasing distance from the spray nozzle in both cases. In the fluidized bed, D50 decreased with the increasing fluidization air volume and inlet air temperature. The effect of NaCl concentration on the mist size was hardly observed, but the degree of suppression of agglomeration during coating increased with the increasing NaCl concentration in the coating solution.

Fuel injector utilizing non-thermal plasma activation

DOEpatents

Coates, Don M [Santa Fe, NM; Rosocha, Louis A [Los Alamos, NM

2009-12-01

A non-thermal plasma assisted combustion fuel injector that uses an inner and outer electrode to create an electric field from a high voltage power supply. A dielectric material is operatively disposed between the two electrodes to prevent arcing and to promote the formation of a non-thermal plasma. A fuel injector, which converts a liquid fuel into a dispersed mist, vapor, or aerosolized fuel, injects into the non-thermal plasma generating energetic electrons and other highly reactive chemical species.

Liquid rims collisions and the formation of fines

NASA Astrophysics Data System (ADS)

Néel, Baptiste; Villermaux, Emmanuel

2017-11-01

As an elementary mechanism for the formation of drops from liquid sheets, we investigate the collision of liquid cylinders. This results from the opening of two nearby holes on a liquid film, growing at a constant speed while collecting liquid into two rims, eventually colliding with each other. In this surface tension driven phenomenon, a unique Weber number We = ρ(2 V) 2 2 a / σ controls a variety of behaviors (ρ , σ are the liquid density and surface tension, and 2 V the relative velocity of the impinging rims, each of individual radius a). At low We , the rims merge through an inelastic, dissipative collision which produces a corrugated ligament, finally breaking into drops of size scaling like a, on average. Above a critical Wec 60 , the collision leads to a splash, with the formation of a thin transverse liquid sheet. We will describe the expansion-retraction dynamics of this secondary sheet and its destabilization, responsible for the production of a mist of finer droplets. These alter sensibly the mean, and overall drops size distribution, thus weighted by a substantial fraction of so-called fines.

Recapture Heterogeneity in Cliff Swallows: Increased Exposure to Mist Nets Leads to Net Avoidance

PubMed Central

Roche, Erin A.; Brown, Charles R.; Brown, Mary Bomberger; Lear, Kristen M.

2013-01-01

Ecologists often use mark-recapture to estimate demographic variables such as abundance, growth rate, or survival for samples of wild animal populations. A common assumption underlying mark-recapture is that all animals have an equal probability of detection, and failure to meet or correct for this assumption–as when certain members of the population are either easier or more difficult to capture than other animals–can lead to biased and inaccurate demographic estimates. We built within-year and among-years Cormack-Jolly-Seber recaptures-only models to identify causes of capture heterogeneity for a population of colonially nesting cliff swallows (Petrochelidon pyrrhonota) caught using mist-netting as a part of a 20-year mark-recapture study in southwestern Nebraska, U.S.A. Daily detection of cliff swallows caught in stationary mist nets at their colony sites declined as the birds got older and as the frequency of netting at a site within a season increased. Experienced birds’ avoidance of the net could be countered by sudden disturbances that startled them into a net, such as when we dropped a net over the side of a bridge or flushed nesting cliff swallows into a stationary net positioned at a colony entrance. Our results support the widely held, but seldom tested, belief that birds learn to avoid stationary mist nets over time, but also show that modifications of traditional field methods can reduce this source of recapture heterogeneity. PMID:23472138

Determination of carbonyl compounds generated from the E-cigarette using coupled silica cartridges impregnated with hydroquinone and 2,4-dinitrophenylhydrazine, followed by high-performance liquid chromatography.

PubMed

Uchiyama, Shigehisa; Ohta, Kazushi; Inaba, Yohei; Kunugita, Naoki

2013-01-01

Carbonyl compounds in E-cigarette smoke mist were measured using coupled silica cartridges impregnated with hydroquinone and 2,4-dinitrophenylhydrazine, followed by high-performance liquid chromatography. A total of 363 E-cigarettes (13 brands) were examined. Four of the 13 E-cigarette brands did not generate any carbonyl compounds, while the other nine E-cigarette brands generated various carbonyl compounds. However, the carbonyl concentrations of the E-cigarette products did not show typical distributions, and the mean values were largely different from the median values. It was elucidated that E-cigarettes incidentally generate high concentrations of carbonyl compounds.

Capturing birds with mist nets: A review

USGS Publications Warehouse

Keyes, B.E.; Grue, C.E.

1982-01-01

Herein we have tried to provide a comprehensive review of mist-netting techniques suitable for both novice and experienced netters. General mist-netting procedures and modifications developed by netters for particular bird species and habitats are included. Factors which influence capture success, including site selection, net specifications and placement, weather, and time of day, are discussed. Guidelines are presented for the care of netted birds and the use of mist-net data in the study of bird communities. The advantages of the use of mist nets over other methods of capturing birds are also discussed.

Water Mist Experiment

NASA Technical Reports Server (NTRS)

2001-01-01

The Water Mist commercial research program is scheduled to fly an investigation on STS-107 in 2002 in the updated Combustion Module (CM-2), a sophisticated combustion chamber plus diagnostic equipment. The Center for the Commercial Applications of Combustion in Space (CCACS), a NASA Commercial Space Center located at the Colorado School of Mines, is investigating the properties of mist fire suppression in microgravity with Industry Partner Environmental Engineering Concepts. These experiments consist of varying water droplet sizes and water mist concentrations applied to flame fronts of different propane/air mixtures. Observations from these tests will provide valuable information on the change of flame speed in the presence of water mist. Shown here is a flame front propagating through the Mist flame tube during 1-g testing at NASA/Glenn Research Center.

Sodium and chloride levels in rainfall, mist. streamwater and groundwater at the Plynlimon catchments, mid-Wales: inferences on hydrological and chemical controls

NASA Astrophysics Data System (ADS)

Neal, C.; Kirchner, J. W.

Variations in sodium and chloride in atmospheric inputs (rainfall and mist), stream runoff and groundwater stores are documented for the upper Severn River (Afon Hafren and Afon Hore catchments), Plynlimon, mid-Wales. The results show five salient features.

1. Sodium and chloride concentrations are highly variable and highly correlated in rainfall and mist. The sodium-chloride relationship in rainfall has a slope close to the sodium/chloride ratio in sea-water, and an intercept that is not significantly different from zero. This indicates that sea-salt is the dominant source of both sodium and chloride in rainfall, which would be expected given the maritime nature of the metrology. For mist, there is also a straight line with near-zero intercept, but with a slightly higher gradient than the sea-salt ratio, presumably due to small additional sodium inputs from other sources.
2. There is an approximate input-output balance for both sodium and chloride, with the exception of one groundwater well, in which high chemical weathering results in an anomalous high Na/Cl ratio. Thus, atmospheric deposition is the dominant source of both sodium and chloride in groundwater and streamflow.
3. The fluctuations in sodium and chloride concentrations in the streams and groundwaters are strongly damped compared to those in the rain and the mist, reflecting the storage and mixing of waters in the subsurface.
4. On all timescales, from weeks to years, sodium fluctuations are more strongly damped than chloride fluctuations in streamflow. The additional damping of sodium is consistent with ion exchange buffering of sodium in the catchment soils.
5. Sodium and chloride concentrations are linearly correlated in the streams and groundwaters, but the slope is almost universally less than the sea-salt ratio and there is a non-zero intercept. The Na/Cl ratio in streamflow and groundwater is higher than the sea-salt ratio when salinity is low and lower than the sea-salt ratio when salinity is high. This pattern of behaviour is again consistent with ion exchange buffering of sodium in the catchment soils.

The use of mist nets as a tool for bird population monitoring

Treesearch

E.H. Dunn; C. John Ralph

2004-01-01

Mist nets are an important tool for population monitoring, here defi ned as assessment of species composition, relative abundance, population size, and demography. We review the strengths and limitations of mist netting for monitoring purposes, based on papers in this volume and other literature. Advantages of using mist nets over aural or visual count methods include...

Oil-air mist lubrication for helicopter gearing

NASA Technical Reports Server (NTRS)

Mcgrogan, F.

1976-01-01

The applicability of a once-through oil mist system to the lubrication of helicopter spur gears was investigated and compared to conventional jet spray lubrication. In the mist lubrication mode, cooling air was supplied at 366K (200 F) to the out of mesh location of the gear sets. The mist air was also supplied at 366K (200 F) to the radial position mist nozzle at a constant rate of 0.0632 mol/s (3 SCFM) per nozzle. The lubricant contained in the mist air varied between 32 - 44 cc/hour. In the recirculating jet spray mode, the flow rate was varied between 1893 - 2650 cc/hour. Visual inspection revealed the jet spray mode produced a superior surface finish on the gear teeth but a thermal energy survey showed a 15 - 20% increase in heat generated. The gear tooth condition in the mist lubrication mode system could be improved if the cooling air and lubricant/air flow ratio were increased. The test gearbox and the procedure used are described.

Mannitol can mitigate negative effects of simulated acid mist and fluoranthene in juvenile Japanese red pine (P. densiflora Sieb. et Zucc.).

PubMed

Oguntimehin, Ilemobayo; Bandai, Sayuri; Sakugawa, Hiroshi

2013-03-01

The negative health effects of simulated acid mists and fluoranthene on juvenile Japanese red pine were investigated, and the methods of protection from these pollutants were examined. The needle gas exchange, chlorophyll fluorescence, chemical contents and visual damage to needles caused by acid mist applied alone or its conjunction with fluoranthene were investigated over 60 d and 20 d, respectively. Acid mist at pH 2 and 3 caused physiological and visual damage, which was enhanced by the addition of fluoranthene to the mist. However, fluoranthene and acid mist at pH 4 and 5 showed only minor effects. These findings indicate that acid mist may be more harmful to pine trees if it occurs in conjunction with polycyclic aromatic hydrocarbons. Moreover, suppression of the singular and additive effects of these compounds was achieved using mannitol, which may be widely applicable to suppression of reactive oxygen species-mediated plant damage. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Water-Mist Fire Suppression Experiment (Mist): Preliminary Results From The STS-107 Mission

NASA Technical Reports Server (NTRS)

Abbud-Madrid, Angel; McKinnon, J. Thomas; Amon, Francine; Gokoglu, Suleyman

2003-01-01

An investigation of the effect of water mists on premixed flame propagation has been conducted onboard the Space Shuttle to take advantage of the prolonged microgravity environment to study the effect of uniformly distributed clouds of polydisperse water mists on the speed and shape of propagating propane-air premixed flames. The suspension of a quiescent and uniform water mist cloud was confirmed during the microgravity tests. Preliminary results show good agreement with trends obtained by the numerical predictions of a computational model that uses a hybrid Eulerian-Lagrangian formulation to simulate the two-phase, flame/mist interaction. Effective flame suppression is observed at progressively higher water loadings and smaller water droplet sizes. Other unusual flame behavior, such as flame front breakup and pulsating flames, is still under investigation. The promising results from the microgravity tests will be used to assess the feasibility of using water mists as fire suppressants on Earth and on spacecraft.

40 CFR 62.3300 - Identification of plan.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Mist Emissions from Existing Sulfuric Acid Production Plants § 62.3300 Identification of plan. (a... Sulfuric Acid Plants.” (b) The plan was officially submitted on August 10, 1978. (c) Identification of sources: The plan includes the following sulfuric acid production plants: (1) Beker Industries in LaSalle...

40 CFR 62.3300 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mist Emissions from Existing Sulfuric Acid Production Plants § 62.3300 Identification of plan. (a... Sulfuric Acid Plants.” (b) The plan was officially submitted on August 10, 1978. (c) Identification of sources: The plan includes the following sulfuric acid production plants: (1) Beker Industries in LaSalle...

41 CFR 50-204.50 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Contaminants for 1968” of the American Conference of Governmental Industrial Hygienists, except for the ANSI... this section, feasible administrative or engineering controls must first be determined and implemented... competent industrial hygienist or other technically qualified source. Table II—Mineral Dusts Substance Mppcf...

41 CFR 50-204.50 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Contaminants for 1968” of the American Conference of Governmental Industrial Hygienists, except for the ANSI... this section, feasible administrative or engineering controls must first be determined and implemented... competent industrial hygienist or other technically qualified source. Table II—Mineral Dusts Substance Mppcf...

41 CFR 50-204.50 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Contaminants for 1968” of the American Conference of Governmental Industrial Hygienists, except for the ANSI... this section, feasible administrative or engineering controls must first be determined and implemented... competent industrial hygienist or other technically qualified source. Table II—Mineral Dusts Substance Mppcf...

41 CFR 50-204.50 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Contaminants for 1968” of the American Conference of Governmental Industrial Hygienists, except for the ANSI... this section, feasible administrative or engineering controls must first be determined and implemented... competent industrial hygienist or other technically qualified source. Table II—Mineral Dusts Substance Mppcf...

41 CFR 50-204.50 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Contaminants for 1968” of the American Conference of Governmental Industrial Hygienists, except for the ANSI... this section, feasible administrative or engineering controls must first be determined and implemented... competent industrial hygienist or other technically qualified source. Table II—Mineral Dusts Substance Mppcf...

40 CFR 62.3300 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mist Emissions from Existing Sulfuric Acid Production Plants § 62.3300 Identification of plan. (a... Sulfuric Acid Plants.” (b) The plan was officially submitted on August 10, 1978. (c) Identification of sources: The plan includes the following sulfuric acid production plants: (1) Beker Industries in LaSalle...

40 CFR 62.3300 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mist Emissions from Existing Sulfuric Acid Production Plants § 62.3300 Identification of plan. (a... Sulfuric Acid Plants.” (b) The plan was officially submitted on August 10, 1978. (c) Identification of sources: The plan includes the following sulfuric acid production plants: (1) Beker Industries in LaSalle...

40 CFR 62.3300 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mist Emissions from Existing Sulfuric Acid Production Plants § 62.3300 Identification of plan. (a... Sulfuric Acid Plants.” (b) The plan was officially submitted on August 10, 1978. (c) Identification of sources: The plan includes the following sulfuric acid production plants: (1) Beker Industries in LaSalle...

Consistency of mist netting and point counts in assessing landbird species richness and relative abundance during migration

Treesearch

Yong Wang; Deborah M. Finch

2002-01-01

We compared consistency of species richness and relative abundance data collected concurrently using mist netting and point counts during migration in riparian habitats along the middle Rio Grande of central New Mexico. Mist netting detected 74% and point counts detected 82% of the 197 species encountered during the study. Species that mist netting failed to capture...

Radiation attenuation and opacity in smoke and water sprays

NASA Astrophysics Data System (ADS)

Parent, Gilles; Boulet, Pascal; Morlon, Romain; Blanchard, Elizabeth

2017-08-01

Radiation attenuation through sprays, smoke and mixings of both media was studied in the infrared and in the visible range, by conducting real scale experiments in a corridor. The effect of water injection by a water mist nozzle and a sprinkler device was investigated. Radiation attenuation in the infrared range and opacity in the visible range were measured, by using a FTIR spectrometer and a dedicated opacimetry device especially designed for the present application. Experiments were done using either a blackbody source for attenuation characterization, or a heptane pool fire aimed at producing smoke for opacity measurements. For tests with smoke, the difficulties raised by the harsh environment involving a hot mixing of gas plus soot and vapor carrying water droplets were circumvented with an original device involving an optical fiber network. Mean infrared transmission was found equal to 12% for the water mist (with a 25 L/min water flowrate) and 37% for the sprinkler (with a 91 L/min water flowrate). Fitting the infrared transmission spectra with results obtained using a Monte Carlo simulation provided an estimation of the water volumetric fraction in the spray. It was shown that the better attenuation capability of the water mist is due to two factors: (1) a higher extinction coefficient of the water mist for a given water volumetric fraction due to the small size of the injected droplets and (2) a higher water volumetric fraction. Opacity measurements in the visible range yielded a measured extinction coefficient in good agreement with an estimation obtained with the Mie theory and the identified water volumetric fraction. Moreover, the water sprays (sprinkler or water mist) was seen to lead to a quick de-stratification of the smoke layer. When the spraying operation was stopped, the visibility re-increased in two main steps: a first step of fast increase and a second step of slow increase needing a few tens of seconds to get again a fully stratified smoke layer.

Oil mist and vapour concentrations from drilling fluids: inter- and intra-laboratory comparison of chemical analyses.

PubMed

Galea, Karen S; Searl, Alison; Sánchez-Jiménez, Araceli; Woldbæk, Torill; Halgard, Kristin; Thorud, Syvert; Steinsvåg, Kjersti; Krüger, Kirsti; Maccalman, Laura; Cherrie, John W; van Tongeren, Martie

2012-01-01

There are no recognized analytical methods for measuring oil mist and vapours arising from drilling fluids used in offshore petroleum drilling industry. To inform the future development of improved methods of analysis for oil mist and vapours this study assessed the inter- and intra-laboratory variability in oil mist and vapour analysis. In addition, sample losses during transportation and storage were assessed. Replicate samples for oil mist and vapour were collected using the 37-mm Millipore closed cassette and charcoal tube assembly. Sampling was conducted in a simulated shale shaker room, similar to that found offshore for processing drilling fluids. Samples were analysed at two different laboratories, one in Norway and one in the UK. Oil mist samples were analysed using Fourier transform infrared spectroscopy (FTIR), while oil vapour samples were analysed by gas chromatography (GC). The comparison of replicate samples showed substantial within- and between-laboratory variability in reported oil mist concentrations. The variability in oil vapour results was considerably reduced compared to oil mist, provided that a common method of calibration and quantification was adopted. The study also showed that losses can occur during transportation and storage of samples. There is a need to develop a harmonized method for the quantification of oil mist on filter and oil vapour on charcoal supported by a suitable proficiency testing scheme for laboratories involved in the analysis of occupational hygiene samples for the petroleum industry. The uncertainties in oil mist and vapour measurement have substantial implications in relation to compliance with occupational exposure limits and also in the reliability of any exposure-response information reported in epidemiological studies.

Gear Mesh Loss-of-Lubrication Experiments and Analytical Simulation

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Polly, Joseph; Morales, Wilfredo

2011-01-01

An experimental program to determine the loss-of-lubrication (LOL) characteristics of spur gears in an aerospace simulation test facility has been completed. Tests were conducted using two different emergency lubricant types: (1) an oil mist system (two different misted lubricants) and (2) a grease injection system (two different grease types). Tests were conducted using a NASA Glenn test facility normally used for conducting contact fatigue. Tests were run at rotational speeds up to 10000 rpm using two different gear designs and two different gear materials. For the tests conducted using an air-oil misting system, a minimum lubricant injection rate was determined to permit the gear mesh to operate without failure for at least 1 hr. The tests allowed an elevated steady state temperature to be established. A basic 2-D heat transfer simulation has been developed to investigate temperatures of a simulated gear as a function of frictional behavior. The friction (heat generation source) between the meshing surfaces is related to the position in the meshing cycle, the load applied, and the amount of lubricant in the contact. Experimental conditions will be compared to those from the 2-D simulation.

Mist collection on parallel fiber arrays

NASA Astrophysics Data System (ADS)

Labbé, Romain; Duprat, Camille

2016-11-01

Fog is an important source of fresh water in specific arid regions such as the Atacama Desert in Chile. The method used to collect water passively from fog, either for domestic consumption or research purposes, consists in erecting large porous fiber nets on which the mist droplets impact. The two main mechanisms involved with this process are the impact of the drops on the fibers and the drainage of the fluid from the net, while the main limiting factor is the clogging of the mesh by accumulated water. We consider a novel collection system, made of an array of parallel fibers, that we study experimentally with a wind mist tunnel. In addition, we develop theoretical models considering the coupling of wind flow, droplet trajectories and wetting of the fibers. We find that the collection efficiency strongly depends on the size and distribution of the drops formed on the fibers, and thus on the fibers diameter, inclination angle and wetting properties. In particular, we show that the collection efficiency is greater when large drops are formed on the fibers. By adjusting the fibers diameter and the inter-fiber spacing, we look for an optimal structure that maximizes the collection surface and the drainage, while avoiding flow deviations.

Mesa Isochrones and Stellar Tracks (MIST). I. Solar-scaled Models

NASA Astrophysics Data System (ADS)

Choi, Jieun; Dotter, Aaron; Conroy, Charlie; Cantiello, Matteo; Paxton, Bill; Johnson, Benjamin D.

2016-06-01

This is the first of a series of papers presenting the Modules for Experiments in Stellar Astrophysics (MESA) Isochrones and Stellar Tracks (MIST) project, a new comprehensive set of stellar evolutionary tracks and isochrones computed using MESA, a state-of-the-art open-source 1D stellar evolution package. In this work, we present models with solar-scaled abundance ratios covering a wide range of ages (5≤slant {log}({Age}) [{year}]≤slant 10.3), masses (0.1≤slant M/{M}⊙ ≤slant 300), and metallicities (-2.0≤slant [{{Z}}/{{H}}]≤slant 0.5). The models are self-consistently and continuously evolved from the pre-main sequence (PMS) to the end of hydrogen burning, the white dwarf cooling sequence, or the end of carbon burning, depending on the initial mass. We also provide a grid of models evolved from the PMS to the end of core helium burning for -4.0≤slant [{{Z}}/{{H}}]\\lt -2.0. We showcase extensive comparisons with observational constraints as well as with some of the most widely used existing models in the literature. The evolutionary tracks and isochrones can be downloaded from the project website at http://waps.cfa.harvard.edu/MIST/.

40 CFR 62.8102 - Identification of plan.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Mist Emissions from Existing Sulfuric Acid Plants § 62.8102 Identification of plan. (a) [Reserved] (b... Plants” of Title 6 of the New York Code of Rules and Regulations effective May 10, 1984. (2) Supplemental information submitted on March 29, 1985. (c) Identification of sources. The plan includes the following plants...

40 CFR 62.8102 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Mist Emissions from Existing Sulfuric Acid Plants § 62.8102 Identification of plan. (a) [Reserved] (b... Plants” of Title 6 of the New York Code of Rules and Regulations effective May 10, 1984. (2) Supplemental information submitted on March 29, 1985. (c) Identification of sources. The plan includes the following plants...

40 CFR 62.8102 - Identification of plan.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Mist Emissions from Existing Sulfuric Acid Plants § 62.8102 Identification of plan. (a) [Reserved] (b... Plants” of Title 6 of the New York Code of Rules and Regulations effective May 10, 1984. (2) Supplemental information submitted on March 29, 1985. (c) Identification of sources. The plan includes the following plants...

40 CFR 62.8102 - Identification of plan.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Mist Emissions from Existing Sulfuric Acid Plants § 62.8102 Identification of plan. (a) [Reserved] (b... Plants” of Title 6 of the New York Code of Rules and Regulations effective May 10, 1984. (2) Supplemental information submitted on March 29, 1985. (c) Identification of sources. The plan includes the following plants...

Multiloop Integral System Test (MIST): MIST Facility Functional Specification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Habib, T F; Koksal, C G; Moskal, T E

1991-04-01

The Multiloop Integral System Test (MIST) is part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox designed plants. MIST is sponsored by the US Nuclear Regulatory Commission, the Babcock Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral facilities to address the thermal-hydraulic SBLOCA questions. MIST was specifically designed and constructed for this program, and an existing facility --more » the Once Through Integral System (OTIS) -- was also used. Data from MIST and OTIS are used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The MIST Functional Specification documents as-built design features, dimensions, instrumentation, and test approach. It also presents the scaling basis for the facility and serves to define the scope of work for the facility design and construction. 13 refs., 112 figs., 38 tabs.« less

Comparison of ultrasonic distillation to sparging of liquid mixtures

NASA Astrophysics Data System (ADS)

Park, Han Jung; Jung, Hye Yun; Calo, Joseph; Diebold, Gerald

2011-04-01

The application of intense ultrasound to a liquid-gas interface results in the formation of an ultrasonic fountain and generates both mist and vapor from the liquid. Here, the composition of the vapor and aerosol above an ultrasonic fountain is determined as a function of irradiation time and compared with the results of sparging for five different solutions. The experimental apparatus for determining the efficiency of separation consists of a glass vessel containing a piezoelectric transducer driven at either 1.65 or 2.40 MHz. Dry nitrogen is passed over the ultrasonic fountain to remove the vapor and aerosol. The compositions of the liquid solutions are recorded as a function of irradiation time using gas chromatography, refractive index measurement, nuclear magnetic resonance, or spectrophotometry. Data are presented for ethanol-water and ethyl acetate-ethanol solutions, cobalt chloride in water, colloidal silica, and colloidal gold. The experiments show that ultrasonic distillation produces separations that are somewhat less complete than what is obtained using sparging.

Application of gas-fluid atomization technology in ultrosonic vibration cutting titanium alloy workpiece

NASA Astrophysics Data System (ADS)

Zhou, Zhimin; Zhang, Yuangliang; Li, Xiaoyan; Sun, Baoyuan

2009-11-01

To further improve machined surface quality of diamond cutting titanium workpiece and reduce diamond tool wear, it puts forward a kind of machining technology with mixture of carbon dioxide gas, water and vegetable oil atomized mist as cooling media in the paper. The cooling media is sprayed to cutting area through gas-liquid atomizer device to achieve purpose of cooling, lubricating, and protecting diamond tool. Experiments indicate that carbon dioxide gas can touch cutting surface more adequately through using gas-liquid atomization technology, which makes iron atoms of cutting surface cause a chemical reaction directly with carbon in carbon dioxide gas and reduce graphitizing degree of diamond tool. Thus, this technology of using gas-liquid atomization and ultrasonic vibration together for cutting Titanium Alloy is able to improve machined surface quality of workpiece and slow of diamond tool wear.

MIUS Integration and Subsystem Test (MIST) data system

NASA Technical Reports Server (NTRS)

Pringle, L. M.

1977-01-01

A data system for use in testing integrated subsystems of a modular integrated utility system (MIUS) is presented. The MIUS integration and subsystem test (MIST) data system is reviewed from its conception through its checkout and operation as the controlling portion of the MIST facility. The MIST data system provides a real time monitoring and control function that allows for complete evaluation of the performance of the mechanical and electrical subsystems, as well as controls the operation of the various components of the system. In addition to the aforementioned capabilities, the MIST data system provides computerized control of test operations such that minimum manpower is necessary to set up, operate, and shut down subsystems during test periods.

Numerical study of chemical reactions in a surface microdischarge tube with mist flow based on experiment

NASA Astrophysics Data System (ADS)

Shibata, T.; Nishiyama, H.

2014-03-01

Recently, a water treatment method of spraying solution into a discharge region has been developed and shows high energy efficiency. In this study, a simulation model of a water treatment method using a surface microdischarge (SMD) tube with mist flow is proposed for further understanding the detailed chemical reactions. Our model has three phases (plasma, gas and liquid) and three simulation steps. The carrier gas is humid air including 2% or 3% water vapour. The chemical species diffusion characteristics in the SMD tube and the concentrations in a droplet are clarified in a wide pH interval. The simulation results show that the chemical species generated on the SMD tube inner wall are diffused to the central axis and dissolved into fine droplets. Especially, OH radicals dissolve into droplets a few mm away from the SMD tube wall because of acidification of the droplets. Furthermore, the hydrogen peroxide density, which is the most important indicator of a radical reaction in water, is influenced by the initial solution pH. This pH dependence results from ozone self-decomposition in water.

Distinct regulatory functions of SLP-76 and MIST in NK cell cytotoxicity and IFN-gamma production.

PubMed

Hidano, Shinya; Sasanuma, Hiroki; Ohshima, Keiko; Seino, Ken-ichiro; Kumar, Lalit; Hayashi, Katsuhiko; Hikida, Masaki; Kurosaki, Tomohiro; Taniguchi, Masaru; Geha, Raif S; Kitamura, Daisuke; Goitsuka, Ryo

2008-03-01

Activation of NK cells is triggered by multiple receptors. We demonstrate here that SLP-76 is required for CD16- and NKG2D-mediated NK cell cytotoxicity, while MIST negatively regulates these responses in an SLP-76-dependent manner. Exceptionally, MIST acts as a positive regulator of cytotoxicity against YAC-1 cells, although SLP-76 plays a more key role. SLP-76 acts as a dominant positive regulator for both NKG2D-mediated and YAC-1 cell-triggered IFN-gamma production. Although NKG2D-mediated IFN-gamma production depends on phospholipase C (PLC) gamma 2, YAC-1 cell-triggered IFN-gamma production is PLC gamma 2- and Syk/ZAP-70 independent and nuclear factor-kappa B mediated. SLP-76 is required for this process in the presence of MIST but is dispensable in the absence of MIST. Thus, YAC-1 cell-triggered NKG2D-independent IFN-gamma production appears to be regulated by SLP-76-dependent and -independent pathways, in which the latter is negatively regulated by MIST. Taken together, these results suggest that SLP-76 and MIST distinctly but interactively regulate NK cell cytotoxicity and IFN-gamma production.

Microgravity

NASA Image and Video Library

2001-01-24

The Water Mist commercial research program is scheduled to fly an investigation on STS-107 in 2002 in the updated Combustion Module (CM-2), a sophisticated combustion chamber plus diagnostic equipment. The Center for the Commercial Applications of Combustion in Space (CCACS), a NASA Commercial Space Center located at the Colorado School of Mines, is investigating the properties of mist fire suppression in microgravity with Industry Partner Environmental Engineering Concepts. These experiments consist of varying water droplet sizes and water mist concentrations applied to flame fronts of different propane/air mixtures. Observations from these tests will provide valuable information on the change of flame speed in the presence of water mist. Shown here is a flame front propagating through the Mist flame tube during 1-g testing at NASA/Glenn Research Center.

MODIS Interactive Subsetting Tool (MIST)

NASA Astrophysics Data System (ADS)

McAllister, M.; Duerr, R.; Haran, T.; Khalsa, S. S.; Miller, D.

2008-12-01

In response to requests from the user community, NSIDC has teamed with the Oak Ridge National Laboratory Distributive Active Archive Center (ORNL DAAC) and the Moderate Resolution Data Center (MrDC) to provide time series subsets of satellite data covering stations in the Greenland Climate Network (GC-NET) and the International Arctic Systems for Observing the Atmosphere (IASOA) network. To serve these data NSIDC created the MODIS Interactive Subsetting Tool (MIST). MIST works with 7 km by 7 km subset time series of certain Version 5 (V005) MODIS products over GC-Net and IASOA stations. User- selected data are delivered in a text Comma Separated Value (CSV) file format. MIST also provides online analysis capabilities that include generating time series and scatter plots. Currently, MIST is a Beta prototype and NSIDC intends that user requests will drive future development of the tool. The intent of this poster is to introduce MIST to the MODIS data user audience and illustrate some of the online analysis capabilities.

Mist characterization in drilling 1018 steel

NASA Astrophysics Data System (ADS)

Cole, Ian

Minimum quantity lubrication replaces the traditional method of flood cooling with small amounts of high-efficient lubrication. Limited studies have been performed to determine the characteristics of mist produced during MQL. This study investigated the mist concentration levels produced while drilling 1018 steel using a vegetable based lubricant. ANOVA was performed to determine whether speed and feed rates or their interactions have a significant effect on mist concentration levels and particle diameter. It was observed that the concentration levels obtained under all four speed and feed rate combinations studied exceeded the current OSHA and NIOSH standards.

Microfog lubrication for aircraft engine bearings

NASA Technical Reports Server (NTRS)

Rosenlieb, J. W.

1976-01-01

An analysis and system study was performed to provide design information regarding lubricant and coolant flow rates and flow paths for effective utilization of the lubricant and coolant in a once through bearing oil mist (microfog) and coolant air system. Both static and dynamic tests were performed. Static tests were executed to evaluate and calibrate the mist supply system. A total of thirteen dynamic step speed bearing tests were performed using four different lubricants and several different mist and air supply configurations. The most effective configuration consisted of supplying the mist and the major portion of the cooling air axially through the bearing. The results of these tests have shown the feasibility of using a once through oil mist and cooling air system to lubricate and cool a high speed, high temperature aircraft engine mainshaft bearing.

Linear Aerospike SR-71 Experiment (LASRE): Aerospace Propulsion Hazard Mitigation Systems

NASA Technical Reports Server (NTRS)

Mizukami, Masashi; Corpening, Griffin P.; Ray, Ronald J.; Hass, Neal; Ennix, Kimberly A.; Lazaroff, Scott M.

1998-01-01

A major hazard posed by the propulsion system of hypersonic and space vehicles is the possibility of fire or explosion in the vehicle environment. The hazard is mitigated by minimizing or detecting, in the vehicle environment, the three ingredients essential to producing fire: fuel, oxidizer, and an ignition source. The Linear Aerospike SR-71 Experiment (LASRE) consisted of a linear aerospike rocket engine integrated into one-half of an X-33-like lifting body shape, carried on top of an SR-71 aircraft. Gaseous hydrogen and liquid oxygen were used as propellants. Although LASRE is a one-of-a-kind experimental system, it must be rated for piloted flight, so this test presented a unique challenge. To help meet safety requirements, the following propulsion hazard mitigation systems were incorporated into the experiment: pod inert purge, oxygen sensors, a hydrogen leak detection algorithm, hydrogen sensors, fire detection and pod temperature thermocouples, water misting, and control room displays. These systems are described, and their development discussed. Analyses, ground test, and flight test results are presented, as are findings and lessons learned.

Velocity of mist droplets and suspending gas imaged separately

NASA Astrophysics Data System (ADS)

Kuethe, Dean O.; McBride, Amber; Altobelli, Stephen A.

2012-03-01

Nuclear Magnetic Resonance Images (MRIs) of the velocity of water droplets and velocity of the suspending gas, hexafluoroethane, are presented for a vertical and horizontal mist pipe flow. In the vertical flow, the upward velocity of the droplets is clearly slower than the upward velocity of the gas. The average droplet size calculated from the average falling velocity in the upward flow is larger than the average droplet size of mist drawn from the top of the pipe measured with a multi-stage aerosol impactor. Vertical flow concentrates larger particles because they have a longer transit time through the pipe. In the horizontal flow there is a gravity-driven circulation with high-velocity mist in the lower portion of the pipe and low-velocity gas in the upper portion. MRI has the advantages that it can image both phases and that it is unperturbed by optical opacity. A drawback is that the droplet phase of mist is difficult to image because of low average spin density and because the signal from water coalesced on the pipe walls is high. To our knowledge these are the first NMR images of mist.

Microscopy image segmentation tool: Robust image data analysis

NASA Astrophysics Data System (ADS)

Valmianski, Ilya; Monton, Carlos; Schuller, Ivan K.

2014-03-01

We present a software package called Microscopy Image Segmentation Tool (MIST). MIST is designed for analysis of microscopy images which contain large collections of small regions of interest (ROIs). Originally developed for analysis of porous anodic alumina scanning electron images, MIST capabilities have been expanded to allow use in a large variety of problems including analysis of biological tissue, inorganic and organic film grain structure, as well as nano- and meso-scopic structures. MIST provides a robust segmentation algorithm for the ROIs, includes many useful analysis capabilities, and is highly flexible allowing incorporation of specialized user developed analysis. We describe the unique advantages MIST has over existing analysis software. In addition, we present a number of diverse applications to scanning electron microscopy, atomic force microscopy, magnetic force microscopy, scanning tunneling microscopy, and fluorescent confocal laser scanning microscopy.

Verification of impact of morning showering and mist sauna bathing on human physiological functions and work efficiency during the day

NASA Astrophysics Data System (ADS)

Lee, Soomin; Fujimura, Hiroko; Shimomura, Yoshihiro; Katsuura, Tetsuo

2015-09-01

Recently, a growing number in Japan are switching to taking baths in the morning (morning bathing). However, the effects of the morning bathing on human physiological functions and work efficiency have not yet been revealed. Then, we hypothesized that the effect of morning bathing on physiological functions would be different from those of night bathing. In this study, we measured the physiological functions and work efficiency during the day following the morning bathing (7:10-7:20) including showering, mist sauna bathing, and no bathing as a control. Ten male healthy young adults participated in this study as the subjects. We evaluated the rectal temperature (Tre), skin temperature (Tsk), heart rate (HR), heart rate variability (HRV), blood pressure (BP), the relative power density of the alpha wave (α-wave ratio) of electroencephalogram, alpha attenuation coefficient (AAC), and the error rate of the task performance. As a result, we found that the HR after the mist sauna bathing was significantly lower than those after no bathing rest 3 (11:00). Furthermore, we verified that the α-wave ratio of the Pz after the mist sauna bathing was significantly lower than those after no bathing during the task 6 (15:00). On the other hand, the α-wave ratio of the Pz after the mist sauna bathing was significantly higher than those after showering during the rest 3 (11:00). Tsk after the mist sauna bathing was higher than those after the showering at 9:00 and 15:00. In addition, the error rate of the task performance after the mist sauna bathing was lower than those after no bathing and showering at 14:00. This study concludes that a morning mist sauna is safe and maintains both skin temperature compared to other bathing methods. Moreover, it is presumed that the morning mist sauna bathing improves work efficiency comparing other bathing methods during the task period of the day following the morning bathing.

Verification of impact of morning showering and mist sauna bathing on human physiological functions and work efficiency during the day.

PubMed

Lee, Soomin; Fujimura, Hiroko; Shimomura, Yoshihiro; Katsuura, Tetsuo

2015-09-01

Recently, a growing number in Japan are switching to taking baths in the morning (morning bathing). However, the effects of the morning bathing on human physiological functions and work efficiency have not yet been revealed. Then, we hypothesized that the effect of morning bathing on physiological functions would be different from those of night bathing. In this study, we measured the physiological functions and work efficiency during the day following the morning bathing (7:10-7:20) including showering, mist sauna bathing, and no bathing as a control. Ten male healthy young adults participated in this study as the subjects. We evaluated the rectal temperature (Tre), skin temperature (Tsk), heart rate (HR), heart rate variability (HRV), blood pressure (BP), the relative power density of the alpha wave (α-wave ratio) of electroencephalogram, alpha attenuation coefficient (AAC), and the error rate of the task performance. As a result, we found that the HR after the mist sauna bathing was significantly lower than those after no bathing rest 3 (11:00). Furthermore, we verified that the α-wave ratio of the Pz after the mist sauna bathing was significantly lower than those after no bathing during the task 6 (15:00). On the other hand, the α-wave ratio of the Pz after the mist sauna bathing was significantly higher than those after showering during the rest 3 (11:00). Tsk after the mist sauna bathing was higher than those after the showering at 9:00 and 15:00. In addition, the error rate of the task performance after the mist sauna bathing was lower than those after no bathing and showering at 14:00. This study concludes that a morning mist sauna is safe and maintains both skin temperature compared to other bathing methods. Moreover, it is presumed that the morning mist sauna bathing improves work efficiency comparing other bathing methods during the task period of the day following the morning bathing.

Aqueous-phase oxidation of green leaf volatiles by hydroxyl radical as a source of SOA: Product identification from methyl jasmonate and methyl salicylate oxidation

NASA Astrophysics Data System (ADS)

Hansel, Amie K.; Ehrenhauser, Franz S.; Richards-Henderson, Nicole K.; Anastasio, Cort; Valsaraj, Kalliat T.

2015-02-01

Green leaf volatiles (GLVs) are a group of biogenic volatile organic compounds (BVOCs) released into the atmosphere by vegetation. BVOCs produce secondary organic aerosol (SOA) via gas-phase reactions, but little is known of their aqueous-phase oxidation as a source of SOA. GLVs can partition into atmospheric water phases, e.g., fog, mist, dew or rain, and be oxidized by hydroxyl radicals (˙OH). These reactions in the liquid phase also lead to products that have higher molecular weights, increased polarity, and lower vapor pressures, ultimately forming SOA after evaporation of the droplet. To examine this process, we investigated the aqueous, ˙OH-mediated oxidation of methyl jasmonate (MeJa) and methyl salicylate (MeSa), two GLVs that produce aqueous-phase SOA. High performance liquid chromatography/electrospray ionization mass spectrometry (HPLC-ESI-MS) was used to monitor product formation. The oxidation products identified exhibit higher molecular mass than their parent GLV due to either dimerization or the addition of oxygen and hydroxyl functional groups. The proposed structures of potential products are based on mechanistic considerations combined with the HPLC/ESI-MS data. Based on the structures, the vapor pressure and the Henry's law constant were estimated with multiple methods (SPARC, SIMPOL, MPBPVP, Bond and Group Estimations). The estimated vapor pressures of the products identified are significantly (up to 7 orders of magnitude) lower than those of the associated parent compounds, and therefore, the GLV oxidation products may remain as SOA after evaporation of the water droplet. The contribution of the identified oxidation products to SOA formation is estimated based on measured HPLC-ESI/MS responses relative to previous aqueous SOA mass yield measurements.

42 CFR 84.1153 - Dust, fume, mist, and smoke tests; canister bench tests; gas masks canisters containing filters...

Code of Federal Regulations, 2014 CFR

2014-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2014-10-01 2014-10-01 false Dust, fume, mist, and smoke tests; canister bench...

42 CFR 84.1153 - Dust, fume, mist, and smoke tests; canister bench tests; gas masks canisters containing filters...

Code of Federal Regulations, 2013 CFR

2013-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2013-10-01 2013-10-01 false Dust, fume, mist, and smoke tests; canister bench...

42 CFR 84.1153 - Dust, fume, mist, and smoke tests; canister bench tests; gas masks canisters containing filters...

Code of Federal Regulations, 2010 CFR

2010-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2010-10-01 2010-10-01 false Dust, fume, mist, and smoke tests; canister bench...

42 CFR 84.1153 - Dust, fume, mist, and smoke tests; canister bench tests; gas masks canisters containing filters...

Code of Federal Regulations, 2011 CFR

2011-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2011-10-01 2011-10-01 false Dust, fume, mist, and smoke tests; canister bench...

42 CFR 84.1153 - Dust, fume, mist, and smoke tests; canister bench tests; gas masks canisters containing filters...

Code of Federal Regulations, 2012 CFR

2012-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2012-10-01 2012-10-01 false Dust, fume, mist, and smoke tests; canister bench...

AN EXPERIMENTAL INVESTIGATION INTO THE EFFECT OF PROCESS CONDITIONS ON THE MASS CONCENTRATION OF CUTTING FLUID MIST IN TURNING. (R825370C057)

EPA Science Inventory

Cutting fluid mists that are generated during machining processes represent a significant waste stream as well as a health hazard to humans. Epidemiological studies have shown a link between worker exposure to cutting fluid mist and an increase in respiratory ailments and seve...

Monitoring productivity with multiple mist-net stations

Treesearch

C. John Ralph; Kimberly Hollinger; Sherri L. Miller

2004-01-01

We evaluated data from 22 mist-net capture stations operated over 5 to 13 years in northern California and southern Oregon, to help develop sampling designs for monitoring using mist nets. In summer, 2.6% of individuals were recaptured at other stations within 1 km of the original banding station, and in fall, 1.4% were recaptured nearby. We recommend...

New records of ectoparasitic Acari (Arachnida) and Streblidae (Diptera) from bats in Jalisco, Mexico.

PubMed

Martínez, Maria M Ramírez; Lopez, M Pilar Ibarra; Iñiguez-Dávalos, Luis Ignacio; Yuill, Thomas; Orlova, Maria V; Reeves, Will K

2016-12-01

Ectoparasites of bats in the Neotropics are diverse and play numerous ecological roles as vectors of microbial pathogens and endoparasites and as food sources for other cave fauna living both on their hosts and in bat roosts. The ectoparasites of bats in Jalisco State of western Mexico have not been as well described as those of other states with recent checklists that have focused primarily on the Yucatan Peninsula. We captured bats from 2011-2015 on the south coast and Sierra de Amula, Jalisco using mist nets, and we removed ectoparasites by hand. We identified 24 species of streblid bat flies and six ectoparasitic mites from bats caught in mist nets. There were an additional eight possibly undescribed species of Streblidae. Our collections extend the known range of species into Jalisco. © 2016 The Society for Vector Ecology.

Modeling of oil mist and oil vapor concentration in the shale shaker area on offshore drilling installations.

PubMed

Bråtveit, Magne; Steinsvåg, Kjersti; Lie, Stein Atle; Moen, Bente E

2009-11-01

The objective of this study was to develop regression models to predict concentrations of oil mist and oil vapor in the workplace atmosphere in the shale shaker area of offshore drilling installations. Collection of monitoring reports of oil mist and oil vapor in the mud handling areas of offshore drilling installations was done during visits to eight oil companies and five drilling contractors. A questionnaire was sent to the rig owners requesting information about technical design of the shaker area. Linear mixed-effects models were developed using concentration of oil mist or oil vapor measured by stationary sampling as dependent variables, drilling installation as random effect, and potential determinants related to process technical parameters and technical design of the shale shaker area as fixed effects. The dataset comprised stationary measurements of oil mist (n = 464) and oil vapor (n = 462) from the period 1998 to 2004. The arithmetic mean concentrations of oil mist and oil vapor were 3.89 mg/m(3) and 39.7 mg/m(3), respectively. The air concentration models including significant determinants such as viscosity of base oil, mud temperature, well section, type of rig, localization of shaker, mechanical air supply, air grids in outer wall, air curtain in front of shakers, and season explained 35% and 17% of the total variance in oil vapor and oil mist, respectively. The developed models could be used to indicate what impact differences in technical design and changes in process parameters have on air concentrations of oil mist and oil vapor. Thus, the models will be helpful in planning control measures to reduce the potential for occupational exposure.

The Mesoscale Ionospheric Simulation Testbed (MIST) Regional Data Assimilation Model (Invited)

NASA Astrophysics Data System (ADS)

Comberiate, J.; Kelly, M. A.; Miller, E.; Paxton, L.

2013-12-01

The Mesoscale Ionospheric Simulation Testbed (MIST) provides a regional nowcast and forecast of electron density values and has sufficient resolution to include equatorial plasma bubbles. The SSUSI instrument on the DMSP F18 satellite has high-resolution nightly observations of plasma bubbles at 8 PM local time throughout the current solar maximum. MIST can assimilate SSUSI UV observations, GPS TEC measurements, and SCINDA S4 readings simultaneously into a single scintillation map over a region of interest. MIST also models ionospheric physics to provide a short-term UHF scintillation forecast based on assimilated data. We will present examples of electron density and scintillation maps from MIST. We will also discuss the potential to predict scintillation occurrence up to 6 hours in advance using observations of the equatorial arcs from SSUSI observations at 5:30 PM local time on the DMSP F17 satellite.

The electronic cigarette. Official statement of the Spanish Society of Pneumology and Thoracic Surgery (SEPAR) on the efficacy, safety and regulation of electronic cigarettes.

PubMed

Jimenez Ruiz, Carlos A; Solano Reina, Segismundo; de Granda Orive, Jose Ignacio; Signes-Costa Minaya, Jaime; de Higes Martinez, Eva; Riesco Miranda, Juan Antonio; Altet Gómez, Neus; Lorza Blasco, Jose Javier; Barrueco Ferrero, Miguel; de Lucas Ramos, Pilar

2014-08-01

The electronic cigarette (EC) is a device formed by three basic elements: battery, atomizer and cartridge. When assembled, it looks like a cigarette. The cartridge contains different substances: propylene glycol, glycerine and, sometimes, nicotine. When the user "vapes", the battery is activated, the atomizer is heated and the liquid is drawn in and vaporized. The smoker inhales the mist produced. Various substances have been detected in this mist: formaldehyde, acetaldehyde and acrolein and some heavy metals. Although these are found in lower concentrations than in cigarettes, they may still be harmful for the human body. Several surveys show that 3-10% of smokers regularly use e-cigarettes. A randomized study has shown that the efficacy of e-cigarettes for helping smokers to quit is similar to nicotine patches. Nevertheless, the study has relevant methodological limitations and reliable conclusions cannot be deduced. This report sets down the Position Statement of the Spanish Society of Pulmonology and Thoracic Surgery (SEPAR) on the efficacy and safety of e-cigarettes. This statement declares that e-cigarettes should be regulated as medicinal products. Copyright © 2013 SEPAR. Published by Elsevier Espana. All rights reserved.

Development of the International Space Station Fine Water Mist Portable Fire Extinguisher

NASA Technical Reports Server (NTRS)

Rodriquez, Branelle; Young, GIna

2013-01-01

The National Aeronautics and Space Administration (NASA) is developing a Fine Water Mist (FWM) Portable Fire Extinguisher (PFE) for use on the International Space Station (ISS). The ISS presently uses two different types of fire extinguishers: a water foam extinguisher in the Russian Segments, and a carbon dioxide extinguisher in the United States Orbital Segments, which include Columbus and Kibo pressurized elements. Currently, there are operational and compatibility concerns with the emergency breathing equipment and the carbon dioxide extinguisher. ISS emergency response breathing equipment does not filter carbon dioxide; therefore, crew members are required to have an oxygen supply present during a fire event since the carbon dioxide PFE creates an unsafe breathing environment. The ISS program recommended a nontoxic fire extinguisher to mitigate this operational risk. The FWM PFE can extinguish a fire without creating a hazardous breathing environment for crewmembers. This paper will discuss the unique functional and performance requirements that have been levied on the FWM PFE, identify unique microgravity design considerations for liquid and gas systems, and discuss the NASA ISS specific fire standards that were developed to establish an acceptable portable fire extinguisher s performance.

Two-phase flow pressure drop and heat transfer during condensation in microchannels with uniform and converging cross-sections

NASA Astrophysics Data System (ADS)

Kuo, Ching Yi; Pan, Chin

2010-09-01

This study experimentally investigates steam condensation in rectangular microchannels with uniform and converging cross-sections and a mean hydraulic diameter of 135 µm. The steam flow in the microchannels was cooled by water cross-flowing along its bottom surface, which is different from other methods reported in the literature. The flow patterns, two-phase flow pressure drop and condensation heat transfer coefficient are determined. The microchannels with the uniform cross-section design have a higher heat transfer coefficient than those with the converging cross-section under condensation in the mist/annular flow regimes, although the latter work best for draining two-phase fluids composed of uncondensed steam and liquid water, which is consistent with the result of our previous study. From the experimental results, dimensionless correlations of condensation heat transfer for the mist and annular flow regions and a two-phase frictional multiplier are developed for the microchannels with both types of cross-section designs. The experimental data agree well with the obtained correlations, with the maximum mean absolute errors of 6.4% for the two-phase frictional multiplier and 6.0% for the condensation heat transfer.

Additives for Water Mist Fire Suppression Systems: A Review

DTIC Science & Technology

2012-11-01

TM 2012-236; R & D pour la défense Canada – Atlantique; novembre 2012. Introduction : On utilisait les halons comme agents extincteurs dans les... 13 Table 11: Results of fire extinguishment tests on kerosene or heptanes pan fires using water mist and water mist with 2 vol...Forafac® WM. ....................................................... 13 x DRDC Atlantic TM 2012-236 This page intentionally left

Fidelity of bats to forest sites revealed from mist-netting recaptures

Treesearch

Roger W. Perry

2011-01-01

Although site fidelity to permanent roost structures by bats is generally known, long-term fidelity to areas such as foraging or drinking sites is unknown. Furthermore, mist-net recaptures of bats over multiple years are rarely reported. Extensive mist-net surveys were conducted over the course of 8 y in the Ouachita National Forest of central Arkansas, United States...

Gas stream cleaning system and method

DOEpatents

Kunchal, S. Kumar; Erck, Louis J.; Harris, Harry A.

1979-04-13

An oil mist and solid particle laden gas from an oil shale retorting operation is initially treated with a temperature controlled oil spray and then by a coalescer to reduce the quantity of oil mist and remove most of the solid particle content of the gas stream and then finally treated by an electrostatic precipitator to essentially remove the oil mist remaining in the gas.

Foliar chlorosis of Dracaena deremensis Engler cv. Warneckii cuttings induced by fluoride

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poole, R.T.; Conover, C.A.

1974-08-01

Unrooted cuttings of Warneckii Dracaena were propagated in various media under mist or surface irrigated 3 times weekly. Cuttings propagated in German peat had more foliar chlorosis than cuttings in bark or calcined clay. Cuttings not receiving mist had slightly more chlorosis than cuttings under mist. Foliar chlorosis was positively correlated (r=0.95) with fluoride content.

Formation of CuAlO2 Film by Ultrasonic Spray Pyrolysis

NASA Astrophysics Data System (ADS)

Iping, S.; Lockman, Zainovia; Hutagalung, S. D.; Kamsul, A.; Matsuda, Atsunori

2011-10-01

Smooth, crack free and homogenous CuAlO2 film was produced by chemical solution deposition process via spray pyrolysis technique on a cleaned Si substrate. The precursor solution used was comprised of a mixture of 45.87 mmol Cu(NO3)2.3H2O and 90 mmol Al(NO3)3.9H2O at ratio of Cu:Al = 1.2:1. The precursor solution was placed in a mist chamber and was atomized by a nebulizer to produce precursor mist. The precursor mist was then carried out by Ar gas and was sprayed onto a heated Si. Two main parameters were studied: the distance between the nozzle of the precursor mist chamber and the Si and the temperature of the Si substrate. It appears that from the XRD data, CuAlO2 can be detected for samples prepared by spraying the precursor mist at temperature of > 550 °C with distance between the nozzle and the substrate of 3cm. Reaction of the Cu and Al ions in the mist near the substrate may have promoted the crystallisation of CuAlO2.

Radiant Barriers Save Energy in Buildings

NASA Technical Reports Server (NTRS)

2014-01-01

Langley Research Center needed to coat the Echo 1 satellite with a fine mist of vaporized metal, and collaborated with industry to create "radiant barrier technology." In 2010, Ryan Garrett learned about a new version of the technology resistant to oxidation and founded RadiaSource in Ogden, Utah, to provide the NASA-derived technology for applications in homes, warehouses, gymnasiums, and agricultural settings.

Process for oil shale retorting

DOEpatents

Jones, John B.; Kunchal, S. Kumar

1981-10-27

Particulate oil shale is subjected to a pyrolysis with a hot, non-oxygenous gas in a pyrolysis vessel, with the products of the pyrolysis of the shale contained kerogen being withdrawn as an entrained mist of shale oil droplets in a gas for a separation of the liquid from the gas. Hot retorted shale withdrawn from the pyrolysis vessel is treated in a separate container with an oxygenous gas so as to provide combustion of residual carbon retained on the shale, producing a high temperature gas for the production of some steam and for heating the non-oxygenous gas used in the oil shale retorting process in the first vessel. The net energy recovery includes essentially complete recovery of the organic hydrocarbon material in the oil shale as a liquid shale oil, a high BTU gas, and high temperature steam.

Probing the Tyrosine Phosphorylation State in Breast Cancer by Src Homology 2 Domain Binding

DTIC Science & Technology

2006-08-01

pervanadate, a potent tyrosine phosphatase inhibitor . In the absence of pervanadate, endogenous phosphatases very rapidly dephosphorylate tyrosine...Shd Loc90525 Crk CrkL Plcg1NCPlcg2NC P85aNC p55gNC Vav1 Vav2 Vav3 Tec Btk Emt Txk Bmx Slp76 Mist MistRK GapNC Chimerin Chimerin 2 Tensin Tem6 Tenc1...Plcg1NCPlcg2NC P85aNC Vav1 Vav2 Vav3 Tec Btk Emt Txk Bmx Slp76 Mist MistRK GapNC Chimerin Chimerin 2 Tensin Tem6 Tenc1 Cis1 Cten Nap4 Rin1 RIn2 Rin3

TRAC-PF1/MOD1 pretest predictions of MIST experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyack, B.E.; Steiner, J.L.; Siebe, D.A.

Los Alamos National Laboratory is a participant in the Integral System Test (IST) program initiated in June 1983 to provide integral system test data on specific issues and phenomena relevant to post small-break loss-of-coolant accidents (SBLOCAs) in Babcock and Wilcox plant designs. The Multi-Loop Integral System Test (MIST) facility is the largest single component in the IST program. During Fiscal Year 1986, Los Alamos performed five MIST pretest analyses. The five experiments were chosen on the basis of their potential either to approach the facility limits or to challenge the predictive capability of the TRAC-PF1/MOD1 code. Three SBLOCA tests weremore » examined which included nominal test conditions, throttled auxiliary feedwater and asymmetric steam-generator cooldown, and reduced high-pressure-injection (HPI) capacity, respectively. Also analyzed were two ''feed-and-bleed'' cooling tests with reduced HPI and delayed HPI initiation. Results of the tests showed that the MIST facility limits would not be approached in the five tests considered. Early comparisons with preliminary test data indicate that the TRAC-PF1/MOD1 code is correctly calculating the dominant phenomena occurring in the MIST facility during the tests. Posttest analyses are planned to provide a quantitative assessment of the code's ability to predict MIST transients.« less

Heat Transfer of Confined Impinging Air-water Mist Jet

NASA Astrophysics Data System (ADS)

Chang, Shyy Woei; Su, Lo May

This paper describes the detailed heat transfer distributions of an atomized air-water mist jet impinging orthogonally onto a confined target plate with various water-to-air mass-flow ratios. A transient technique was used to measure the full field heat transfer coefficients of the impinging surface. Results showed that the high momentum mist-jet interacting with the water-film and wall-jet flows created a variety of heat transfer contours on the impinging surface. The trade-off between the competing influences of the different heat transfer mechanisms involving in an impinging mist jet made the nonlinear variation tendency of overall heat transfer against the increase of water-to-air mass-flow ratio and extended the effective cooling region. With separation distances of 10, 8, 6 and 4 jet-diameters, the spatially averaged heat transfer values on the target plate could respectively reach about 2.01, 1.83, 2.43 and 2.12 times of the equivalent air-jet values, which confirmed the applicability of impinging mist-jet for heat transfer enhancement. The optimal choices of water-to-air mass-flow ratio for the atomized mist jet required the considerations of interactive and combined effects of separation distance, air-jet Reynolds number and the water-to-air mass-flow ratio into the atomized nozzle.

Rapid Analysis of Ingredients in Cream Using Ultrasonic Mist-Direct Analysis in Real-Time Time-of-Flight Mass Spectrometry

NASA Astrophysics Data System (ADS)

Shimada, Haruo; Maeno, Katsuyuki; Kinoshita, Kazumasa; Shida, Yasuo

2017-07-01

A novel method for the simultaneous detection of ingredients in pharmaceutical applications such as creams and lotions was developed. An ultrasonic atomizer has been used to produce a mist containing ingredients. The analyte molecules in the mist can be ionized by using direct analysis in real time (DART) at lower temperature than traditionally used, and we thus solved the problem of normal DART-MS measurement using a high-temperature gas. Thereby, molecular-related ions of heat-unstable components and nonvolatile components became detectable. The deprotonated molecular ion of glycyrrhizic acid (m/z 821), which is unstable at high temperatures, was detected without pyrolysis by ultrasonic mist-DART-MS using unheated helium gas, although it was not detected by normal DART-MS using heated helium gas. The cationized molecular ions of derivatives of polyethylene glycol fatty acid monoesters, which are nonvolatile compounds, were also detected as m/z peaks observed from 800 to 2300. Although the protonated molecular ion of tocopherol acetate was not detected in ionization by ultrasonic mist, it was detected by ultrasonic mist-DART-MS even in the emulsion. It was not necessary to dissolve a sample completely to detect its ions. This method enabled us to obtain the composition of pharmaceutical applications simply and rapidly.

Evaluation of 2 Heat-Mitigation Methods in Army Trainees.

PubMed

Sefton, JoEllen M; McAdam, J S; Pascoe, David D; Lohse, K R; Banda, Robert L; Henault, Corbin B; Cherrington, Andrew R; Adams, N E

2016-11-01

 Heat injury is a significant threat to military trainees. Different methods of heat mitigation are in use across military units. Mist fans are 1 of several methods used in the hot and humid climate of Fort Benning, Georgia.  To determine if (1) the mist fan or the cooling towel effectively lowered participant core temperature in the humid environment found at Fort Benning and (2) the mist fan or the cooling towel presented additional physiologic or safety benefits or detriments when used in this environment.  Randomized controlled clinical trial.  Laboratory environmental chamber.  Thirty-five physically active men aged 19 to 35 years.  (1) Mist fan, (2) commercial cooling towel, (3) passive-cooling (no intervention) control. All treatments lasted 20 minutes. Participants ran on a treadmill at 60% V̇o 2 max.  Rectal core temperature, heart rate, thermal comfort, perceived temperature, perceived wetness, and blood pressure.  Average core temperature increased during 20 minutes of cooling (F 1,28 = 64.76, P < .001, η p 2 = 0.70), regardless of group (F 1,28 = 3.41, P = .08, η p 2 = 0.11) or condition (F 1,28 < 1.0). Core temperature, heart rate, and blood pressure did not differ among the 3 conditions. Perceived temperature during 20 minutes of cooling decreased (F 1,30 = 141.19, P < .001, η p 2 = 0.83) regardless of group or condition. Perceived temperature was lower with the mist-fan treatment than with the control treatment (F 1,15 = 7.38, P = .02, η p 2 = 0.32). The mist-fan group perceived themselves to be cooler even at elevated core temperatures.  The mist fan and cooling towel were both ineffective at lowering core temperature. Core temperature continued to increase after exercise in all groups. The mist fan produced feelings of coolness while the core temperature remained elevated, possibly increasing the risk of heat illness.

Evaluation of 2 Heat-Mitigation Methods in Army Trainees

PubMed Central

Sefton, JoEllen M.; McAdam, J. S.; Pascoe, David D.; Lohse, K. R.; Banda, Robert L.; Henault, Corbin B.; Cherrington, Andrew R.; Adams, N. E.

2016-01-01

Context: Heat injury is a significant threat to military trainees. Different methods of heat mitigation are in use across military units. Mist fans are 1 of several methods used in the hot and humid climate of Fort Benning, Georgia. Objectives: To determine if (1) the mist fan or the cooling towel effectively lowered participant core temperature in the humid environment found at Fort Benning and (2) the mist fan or the cooling towel presented additional physiologic or safety benefits or detriments when used in this environment. Design: Randomized controlled clinical trial. Setting: Laboratory environmental chamber. Patients or Other Participants: Thirty-five physically active men aged 19 to 35 years. Intervention(s): (1) Mist fan, (2) commercial cooling towel, (3) passive-cooling (no intervention) control. All treatments lasted 20 minutes. Participants ran on a treadmill at 60% V̇o2max. Main Outcome Measure(s): Rectal core temperature, heart rate, thermal comfort, perceived temperature, perceived wetness, and blood pressure. Results: Average core temperature increased during 20 minutes of cooling (F1,28 = 64.76, P < .001, ηp2 = 0.70), regardless of group (F1,28 = 3.41, P = .08, ηp2 = 0.11) or condition (F1,28 < 1.0). Core temperature, heart rate, and blood pressure did not differ among the 3 conditions. Perceived temperature during 20 minutes of cooling decreased (F1,30 = 141.19, P < .001, ηp2 = 0.83) regardless of group or condition. Perceived temperature was lower with the mist-fan treatment than with the control treatment (F1,15 = 7.38, P = .02, ηp2 = 0.32). The mist-fan group perceived themselves to be cooler even at elevated core temperatures. Conclusions: The mist fan and cooling towel were both ineffective at lowering core temperature. Core temperature continued to increase after exercise in all groups. The mist fan produced feelings of coolness while the core temperature remained elevated, possibly increasing the risk of heat illness. PMID:27710091

Autumn MIST 2012

NASA Astrophysics Data System (ADS)

Fear, Robert; Woodfield, Emma

2013-04-01

Robert Fear and Emma Woodfield report on the Autumn MIST meeting, concerning the solar wind; magnetospheres of planets and comets; ionospheres, thermospheres and mesospheres and how these regions connect.

Lipoid pneumonia caused by oil mist exposure from a steel rolling tandem mill

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cullen, M.R.; Balmes, J.R.; Robins, J.M.

1981-01-01

Five of nine active tandem mill operators exposed at work to aerosolized hydrocarbon mist were referred for evaluation of respiratory complaints. The worker with the longest exposure had reduced lung volumes; he was admitted to the hospital for detailed study. Exercise studies revealed work load limited by ventilation and arterial oxygen desaturation. Flexible fiberoptic bronchoscopy with bronchoalveolar lavage and transbronchial biopsy revealed evidence of lipoid pneumonia. Assessment of the mill revealed levels of respirable oil mist by personal samplers throughout the area far below the currently accepted standard of 5 mg/M3. These findings confirm a 20-year-old hypothesis of J.G. Jonesmore » regarding the hazard of oil mist in this industrial setting.« less

Comparison of the SidePak personal monitor with the Aerosol Particle Sizer (APS).

PubMed

Sánchez Jiménez, Araceli; van Tongeren, Martie; Galea, Karen S; Steinsvåg, Kjersti; MacCalman, Laura; Cherrie, John W

2011-06-01

The aim of this study was to compare the performance of the TSI Aerodynamic Particle Sizer (APS) and the TSI portable photometer SidePak to measure airborne oil mist particulate matter (PM) with aerodynamic diameters below 10 μm, 2.5 μm and 1 μm (PM(10), PM(2.5) and PM(1)). Three SidePaks each fitted with either a PM(10), PM(2.5) or a PM(1) impactor and an APS were run side by side in a controlled chamber. Oil mist from two different mineral oils and two different drilling fluid systems commonly used in offshore drilling technologies were generated using a nebulizer. Compared to the APS, the SidePaks overestimated the concentration of PM(10) and PM(2.5) by one order of magnitude and PM(1) concentrations by two orders of magnitude after exposure to oil mist for 3.3-6.5 min at concentrations ranging from 0.003 to 18.1 mg m(-3) for PM(10), 0.002 to 3.96 mg m(-3) for PM(2.5) and 0.001 to 0.418 mg m(-3) for PM(1) (as measured by the APS). In a second experiment a SidePak monitor previously exposed to oil mist overestimated PM(10) concentrations by 27% compared to measurements from another SidePak never exposed to oil mist. This could be a result of condensation of oil mist droplets in the optical system of the SidePak. The SidePak is a very useful instrument for personal monitoring in occupational hygiene due to its light weight and quiet pump. However, it may not be suitable for the measurement of particle concentrations from oil mist.

Attempted establishment of proficiency levels for laparoscopic performance on a national scale using simulation: the results from the 2004 SAGES Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) learning center study.

PubMed

Van Sickle, K R; Ritter, E M; McClusky, D A; Lederman, A; Baghai, M; Gallagher, A G; Smith, C D

2007-01-01

The Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) has been well validated as a training device for laparoscopic skills. It has been demonstrated that training to a level of proficiency on the simulator significantly improves operating room performance of laparoscopic cholecystectomy. The purpose of this project was to obtain a national standard of proficiency using the MIST-VR based on the performance of experienced laparoscopic surgeons. Surgeons attending the Society of American Gastrointestinal Endoscopic Surgeons (SAGES) 2004 Annual Scientific Meeting who had performed more than 100 laparoscopic procedures volunteered to participate. All the subjects completed a demographic questionnaire assessing laparoscopic and MIST-VR experience in the learning center of the SAGES 2004 meeting. Each subject performed two consecutive trials of the MIST-VR Core Skills 1 program at the medium setting. Each trial involved six basic tasks of increasing difficulty: acquire place (AP), transfer place (TP), traversal (TV), withdrawal insert (WI), diathermy task (DT), and manipulate diathermy (MD). Trial 1 was considered a "warm-up," and trial 2 functioned as the test trial proper. Subject performance was scored for time, errors, and economy of instrument movement for each task, and a cumulative total score was calculated. Trial 2 data are expressed as mean time in seconds in Table 2. Proficiency levels for laparoscopic skills have now been established on a national scale by experienced laparoscopic surgeons using the MIST-VR simulator. Residency programs, training centers, and practicing surgeons can now use these data as guidelines for performance criterion during MIST-VR skills training.

29 CFR 1926.55 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Nitrous oxide 10024-97-2 E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist... — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist Total dust — — Respirable...

29 CFR 1926.55 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Nitrous oxide 10024-97-2 E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist... — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist Total dust — — Respirable...

29 CFR 1926.55 - Gases, vapors, fumes, dusts, and mists.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Nitrous oxide 10024-97-2 E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist... — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist Total dust — — Respirable...

Placing Tactical Data into the MIST and LC2IEDM Systems

DTIC Science & Technology

2003-10-01

Defence R& D Canada DEFENCE DÉFENSE & Placing Tactical Data into the MIST and LC2IEDM Systems Anthony W. Isenor Technical Memorandum DRDC Atlantic TM...intentionally left blank. Copy No: Placing Tactical Data into the MIST and LC2IEDM Systems Anthony W. Isenor Defence R& D Canada – Atlantic Technical...currently underway at Defence R& D Canada – Atlantic, as well as international efforts with The Technical Cooperation Program (TTCP). Both groups

A tale of two trainers: virtual reality versus a video trainer for acquisition of basic laparoscopic skills.

PubMed

Debes, Anders J; Aggarwal, Rajesh; Balasundaram, Indran; Jacobsen, Morten B

2010-06-01

This study aimed to assess the transferability of basic laparoscopic skills between a virtual reality simulator (MIST-VR) and a video trainer box (D-Box). Forty-six medical students were randomized into 2 groups, training on MIST-VR or D-Box. After training with one modality, a crossover assessment on the other was performed. When tested on MIST-VR, the MIST-VR group showed significantly shorter time (90.3 seconds vs 188.6 seconds, P <.001), better economy of movements (4.40 vs 7.50, P <.001), and lower score (224.7 vs 527.0, P <.001). However, when assessed on the D-Box, there was no difference between the groups for time (402.0 seconds vs 325.6 seconds, P = .152), total hand movements (THC) (289 vs 262, P = .792), or total path length (TPL) (34.9 m vs 34.6 m, P = .388). Both simulators provide significant improvement in performance. Our results indicate that skills learned on the MIST-VR are transferable to the D-Box, but the opposite cannot be demonstrated. Copyright 2010 Elsevier Inc. All rights reserved.

Ozone-mist spray sterilization for pest control in agricultural management

NASA Astrophysics Data System (ADS)

Ebihara, Kenji; Mitsugi, Fumiaki; Ikegami, Tomoaki; Nakamura, Norihito; Hashimoto, Yukio; Yamashita, Yoshitaka; Baba, Seiji; Stryczewska, Henryka D.; Pawlat, Joanna; Teii, Shinriki; Sung, Ta-Lun

2013-02-01

We developed a portable ozone-mist sterilization system to exterminate pests (harmful insects) in agricultural field and greenhouse. The system is composed of an ozone generator, an ozone-mist spray and a small container of ozone gas. The ozone generator can supply highly concentrated ozone using the surface dielectric barrier discharge. Ozone-mist is produced using a developed nozzle system. We studied the effects of ozone-mist spray sterilization on insects and agricultural plants. The sterilization conditions are estimated by monitoring the behavior of aphids and observing the damage of the plants. It was shown that aphids were exterminated in 30 s without noticeable damages of the plant leaves. The reactive radicals with strong oxidation potential such as hydroxyl radical (*OH), hydroperoxide radical (*HO2), the superoxide ion radical (*O2‒) and ozonide radical ion (*O3‒) can increase the sterilization rate for aphids. Contribution to the Topical Issue "13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII)", Edited by Nicolas Gherardi, Henryca Danuta Stryczewska and Yvan Ségui.

Computer simulation of thermal and fluid systems for MIUS integration and subsystems test /MIST/ laboratory. [Modular Integrated Utility System

NASA Technical Reports Server (NTRS)

Rochelle, W. C.; Liu, D. K.; Nunnery, W. J., Jr.; Brandli, A. E.

1975-01-01

This paper describes the application of the SINDA (systems improved numerical differencing analyzer) computer program to simulate the operation of the NASA/JSC MIUS integration and subsystems test (MIST) laboratory. The MIST laboratory is designed to test the integration capability of the following subsystems of a modular integrated utility system (MIUS): (1) electric power generation, (2) space heating and cooling, (3) solid waste disposal, (4) potable water supply, and (5) waste water treatment. The SINDA/MIST computer model is designed to simulate the response of these subsystems to externally impressed loads. The computer model determines the amount of recovered waste heat from the prime mover exhaust, water jacket and oil/aftercooler and from the incinerator. This recovered waste heat is used in the model to heat potable water, for space heating, absorption air conditioning, waste water sterilization, and to provide for thermal storage. The details of the thermal and fluid simulation of MIST including the system configuration, modes of operation modeled, SINDA model characteristics and the results of several analyses are described.

Virtual reality laparoscopic simulator for assessment in gynaecology.

PubMed

Gor, Mounna; McCloy, Rory; Stone, Robert; Smith, Anthony

2003-02-01

A validated virtual reality laparoscopic simulator minimally invasive surgical trainer (MIST) 2 was used to assess the psychomotor skills of 21 gynaecologists (2 consultants, 8 registrars and 11 senior house officers). Nine gynaecologists failed to complete the VR tasks at the first attempt and were excluded for sequential evaluation. Each of the remaining 12 gynaecologists were tested on MIST 2 on four occasions within four weeks. The MIST 2 simulator provided quantitative data on time to complete tasks, errors, economy of movement and economy of diathermy use--for both right and left hand performance. The results show a significant early learning curve for the majority of tasks which plateaued by the third session. This suggests a high quality surgeon-computer interface. MIST 2 provides objective assessment of laparoscopic skills in gynaecologists.

A Preliminary Study on the Vapor/Mist Phase Lubrication of a Spur Gearbox

NASA Technical Reports Server (NTRS)

Morales, Wilfredo; Handschuh, Robert F.

1999-01-01

Organophosphates have been the primary compounds used in vapor/mist phase lubrication studies involving ferrous bearing material. Experimental results have indicated that the initial formation of an iron phosphate film on a rubbing ferrous surface, followed by the growth (by cationic diffusion) of a lubricious pyrophosphate-type coating over the iron phosphate, is the reason organophosphates work well as vapor/mist phase lubricants. Recent work, however, has shown that this mechanism leads to the depletion of surface iron atoms and to eventual lubrication failure. A new organophosphate formulation was developed which circumvents surface iron depletion. This formulation was tested by generating an iron phosphate coating on an aluminum surface. The new formulation was then used to vapor/mist phase lubricate a spur gearbox in a preliminary study.

Chalcogenide Glass Lasers on Silicon Substrate Integrated Photonics

DTIC Science & Technology

2016-07-08

AFRL-AFOSR-UK-TR-2016-0013 Chalcogenide glass lasers on silicon substrate integrated photonics Clara Dimas MASDAR INSTITUTE OF SCIENCE & TECHNOLOGY...PROJECT NUMBER 5e.  TASK NUMBER 5f.  WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) MASDAR INSTITUTE OF SCIENCE & TECHNOLOGY - MIST...communication by reducing coupling losses, chip size, energy requirements and manufacturing cost. Chalcogenide glass (ChG) light sources doped with rare earth

Improving effectiveness of protection efforts in tiger source sites: Developing a framework for law enforcement monitoring using MIST.

PubMed

Stokes, Emma J

2010-12-01

Wild tigers are in a critical state with an estimated population decline of more than 95% over the past century. Improving the capacity and effectiveness of law enforcement in reducing poaching of tigers is an immediate priority to secure remaining wild populations in source sites. From 2008-2010, standardized patrol-based law enforcement monitoring (LEM) was established under the Tigers Forever Program across 8 key tiger sites in order to improve and evaluate law enforcement interventions. Patrol-based monitoring has the distinct advantage of providing regular and rapid information on illegal activities and ranger performance, although, until recently, it has received relatively little scrutiny from the conservation community. The present paper outlines a framework for implementation of LEM in tiger source sites using MIST, a computerized management information system for ranger-based data collection. The framework addresses many of the technical, practical and institutional challenges involved in the design, implementation, sustainability and evaluation of LEM. Adoption of such a framework for LEM is a cost-effective strategy to improve the efficiency of law enforcement efforts, to increase the motivation of enforcement staff and to promote the accountability of law enforcement agencies in addressing threats to tigers. When combined with independent, systematic and science-based monitoring of tigers and their prey, LEM has great potential for evaluating the effectiveness of protection-based conservation investments. © 2010 ISZS, Blackwell Publishing and IOZ/CAS.

Mixed Convective Condensation in Enclosures with Noncondensable Gases

NASA Astrophysics Data System (ADS)

Fox, Richard John

1994-01-01

A transient, two-dimensional, numerical model was developed in order to study the laminar flow, heat, and mass transfer in a vertical reflux condenser loaded with vapor and noncondensable gas. The simplified model treats the two-component (gas/vapor), two-phase (vapor/liquid) mixture as a continuum by making use of conservation equations for mass continuity, momentum, species, and energy. The liquid mist phase is formed in such a way as to obey one of three conditions: thermodynamic equilibrium, complete nonequilibrium (no mist formation), or partial equilibrium (partial supersaturation). In developing the model, special attention was paid to the formulation of the boundary conditions, global continuity, and numerical efficiency. Two different mixture combinations were used in order to create stable and unstable systems. Steam-helium mixtures (Mv, = 18, Mg = 4) were found to exhibit stable flows with the lighter helium trapped in the upper portion of the condenser, shutting off condensation in that region. Steam-air mixtures (M_ {v}, = 18, Mg = 28) were found to exhibit varying degrees of instability, depending on the noncondensable gas and heat load, owing to the accumulation of the heavy gas near the condensing surface. Under low gas loading cases (Pg = 0.031 kg/m^3) the natural convective fluctuations were found to be weak and the flow was more easily dominated by the forced convective inlet flow and wall suction. At such low gas loadings, stable, asymmetric flow patterns persisted up to high powers. Large gas loadings (Pg = 0.196 kg/m^3) showed much stronger natural convective effects. Regions of counterflowing vapor and gas were found to promote stronger mixing as the power was increased. Regions of noncondensing gas were found to blanket the condenser walls as the suction velocity increased, resulting in a strong resistance to heat and mass transfer and consequent increase in system pressure. Moderate gas loadings (Pg = 0.065 kg/m ^3) were found to exhibit intermediate behavior between the low and high gas loading cases. For the moderate gas loading cases, a bifurcation was found to occur when Re was increased beyond a critical value, forcing the system into one of two stable, distinct flow patterns. Each branch of the bifurcation was found to correspond to the flows that occur in either the low or high gas loading cases, and radically different heat transfer performance was encountered for the same system parameters. The model was also used to simulate experiments conducted in a vertical reflux thermosyphon using steam -air mixtures. The qualitative aspects of the flow were in reasonable agreement between the model and experiment and trends in the local heat transfer were similar. By converting latent heat energy into sensible heat energy, mist formation was found to increase the system temperature and, as a consequence, the overall heat transfer coefficient was lowered. However, the total heat transfer rate was not sensitive to mist formation since the reduction in the latent heat transfer was accompanied by a corresponding increase in the sensible heat transfer, altering the mode but not the magnitude of the total heat transfer.

Removal of sulfuric acid mist from lead-acid battery plants by coal fly ash-based sorbents.

PubMed

Shu, Yuehong; Wei, Xiangyu; Fang, Yu; Lan, Bingyan; Chen, Hongyu

2015-04-09

Sorbents from coal fly ash (CFA) activated by NaOH, CaO and H2O were prepared for H2SO4 mist removal from lead-acid battery plants. The effects of parameters including temperature, time, the ratios of CFA/activator and water/solid during sorbent preparation were investigated. It is found that the synthesized sorbents exhibit much higher removal capacity for H2SO4 mist when compared with that of raw coal fly ash and CaO except for H2O activated sorbent and this sorbent was hence excluded from the study because of its low capacity. The H2SO4 mist removal efficiency increases with the increasing of preparation time length and temperature. In addition, the ratios of CFA/activator and water/solid also impact the removal efficiency, and the optimum preparation conditions are identified as: a water/solid ratio of 10:1 at 120 °C for 10h, a CFA:CaO weight ratio of 10:1, and a NaOH solution concentration of 3 mol/L. The formation of rough surface structure and an increased surface area after NaOH/CaO activation favor the sorption of H2SO4 mist and possible sorption mechanisms might be electrostatic attractions and chemical precipitation between the surface of sorbents and H2SO4 mist. Copyright © 2015 Elsevier B.V. All rights reserved.

Overview of major hazards. Part 2: Source term; dispersion; combustion; blast, missiles, venting; fire; radiation; runaway reactions; toxic substances; dust explosions

NASA Astrophysics Data System (ADS)

Vilain, J.

Approaches to major hazard assessment and prediction are reviewed. Source term: (phenomenology/modeling of release, influence on early stages of dispersion); dispersion (atmospheric advection, diffusion and deposition, emphasis on dense/cold gases); combustion (flammable clouds and mists covering flash fires, deflagration, transition to detonation; mostly unconfined/partly confined situations); blast formation, propagation, interaction with structures; catastrophic fires (pool fires, torches and fireballs; highly reactive substances) runaway reactions; features of more general interest; toxic substances, excluding toxicology; and dust explosions (phenomenology and protective measures) are discussed.

Comparison Between Oil-mist and Oil-jet Lubrication of High-speed, Small-bore, Angular-contact Ball Bearings

NASA Technical Reports Server (NTRS)

Pinel, Stanley I.; Signer, Hans R.; Zaretsky, Erwin V.

2001-01-01

Parametric tests were conducted with an optimized 35-mm-bore-angular-contact ball bearing on a high-speed, high-temperature bearing tester. Results from both air-oil mist lubrication and oil-jet lubrication systems used to lubricate the bearing were compared to speeds of 2.5 x 10(exp 6) DN. The maximum obtainable speed with air-oil mist lubrication is 2.5 x 10(exp 6) DN. Lower bearing temperatures and higher power losses are obtained with oil-jet lubrication than with air-oil mist lubrication. Bearing power loss is a direct function of oil flow to the bearing and independent of oil delivery system. For a given oil-flow rate, bearing temperature and power loss increase with increases in speed. Bearing life is an inverse function of temperature, the difference in temperature between the individual bearing ring components, and the resultant elastohydrodynamic (EHD) film thicknesses. Bearing life is independent of the oil delivery system except as it affects temperature. Cage slip increased with increases in speed. Cage slip as high as 7 percent was measured and was generally higher with air-oil mist lubrication than with oil-jet lubrication.

Microfog lubricant application system for advanced turbine engine components, phase 2. Tasks 3, 4 and 5: Wettability and heat transfer of microfog jets impinging on a heated rotating disc, and evaluation of reclassifying nozzles and a vortex mist generator

NASA Technical Reports Server (NTRS)

Shim, J.; Leonardi, S. J.

1972-01-01

The wettabilities and heat transfer rates of microfog jets (oil-mist nozzle flows) impinging on a heated rotating disc were determined under an inert atmosphere of nitrogen at temperatures ranging from 600 to 800 F. The results are discussed in relation to the various factors involved in the microfog lubricant application systems. Two novel reclassifying nozzles and a vortex mist generator were also studied.

Evaluation of the econo-mist device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

The Emission Control Technology Division (ECTD) was contacted by the General Services Administration (GSA) concerning a vapor injection device for use with automobile engines. The device is called the Econo-Mist and is a product of the FAP Corporation of Albuquerque, New Mexico. GSA had received information that the Econo-Mist reduced hydrocarbon and carbon monoxide emissions and increased fuel economy. At the request of GSA, ECTD agreed to test the device. A sample of the device was brought to the EPA laboratory in Ann Arbor, Michigan by FAP Corporation personnel on January 13, 1975.

Exposure to oil mist and oil vapour during offshore drilling in norway, 1979-2004.

PubMed

Steinsvåg, Kjersti; Bråtveit, Magne; Moen, Bente E

2006-03-01

To describe personal exposure to airborne hydrocarbon contaminants (oil mist and oil vapour) from 1979 to 2004 in the mud-handling areas of offshore drilling facilities operating on the Norwegian continental shelf when drilling with oil-based muds. Qualitative and quantitative information was gathered during visits to companies involved in offshore oil and gas production in Norway. Monitoring reports on oil mist and oil vapour exposure covered 37 drilling facilities. Exposure data were analysed using descriptive statistics and by constructing linear mixed-effects models. Samples had been taken during the use of three generations of hydrocarbon base oils, namely diesel oils (1979-1984), low-aromatic mineral oils (1985-1997) and non-aromatic mineral oils (1998-2004). Sampling done before 1984 showed high exposure to diesel vapour (arithmetic mean, AM = 1217 mg m(-3)). When low-aromatic mineral oils were used, the exposure to oil mist and oil vapour was 4.3 and 36 mg m(-3), and the respective AMs for non-aromatic mineral oils were reduced to 0.54 and 16 mg m(-3). Downward time trends were indicated for both oil mist (6% per year) and oil vapour (8% per year) when the year of monitoring was introduced as a fixed effect in a linear mixed-effects model analysis. Rig type, technical control measures and mud temperature significantly determined exposure to oil mist. Rig type, type of base oil, viscosity of the base oil, work area, mud temperature and season significantly determined exposure to oil vapour. Major decreases in variability were found for the between-rig components. Exposure to oil mist and oil vapour declined over time in the mud-handling areas of offshore drilling facilities. Exposure levels were associated with rig type, mud temperature, technical control measures, base oil, viscosity of the base oil, work area and season.

Mist Propagation of Juvenile Oak Cuttings

Treesearch

R. E. Farmer

1965-01-01

Greenwood apical cuttings from 1- to 4-month-old cherrybark oak (Quercus falcata var. pagodaefolia Ell.) seedlings have been rooted in 4 weeks under mist, after treatment with indolebutyric acid. The technique is suitable for establishing small clones.

Toxicity of sulfuric acid mist

DOE Office of Scientific and Technical Information (OSTI.GOV)

Treon, J.F.; Dutra, F.R.; Cappel, J.

1950-01-01

Various species were exposed to sulfuric acid mist, 95% less than 2 ..mu..m. Mortality data show susceptibility: guinea pigs > mice > rats > rabbits. Lesions included the following: degeneration of respiratory tract epithelium, hyperemia, edema, focal hemorrhage, patchy atelectasis, and emphysema.

Slanted baffle mist eliminator

DOEpatents

Vance, Richard F.

1995-11-07

An apparatus for the elimination of mist from off-gas during vitrification f nuclear waste, where baffles are installed on a slant toward the flow of the off-gasses eliminating the need to expand the cross-sectional area of the duct size.

Steam inhalation or humidified oxygen for acute bronchiolitis in children up to three years of age.

PubMed

Umoren, Rachel; Odey, Friday; Meremikwu, Martin M

2011-01-19

Acute bronchiolitis is a common respiratory infection and a major cause of morbidity in young children. It is treated with bronchodilators (for example, salbutamol), corticosteroids or humidified air (steam inhalation or cool mist). Steam inhalation is preferred in low-income countries as it is inexpensive and easily available. It is thought to act as a secretolytic agent to lighten secretions in the respiratory tract and relieve respiratory distress. To evaluate the effect of steam inhalation or humidified oxygen to relieve respiratory distress and to evaluate adverse events in children up to three years old with acute bronchiolitis. We searched the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2010, Issue 1) which contains the Acute Respiratory Infections Group's Specialised Register, MEDLINE (1950 to February Week 4, 2010), EMBASE.com (1974 to March 2010), CINAHL (1981 to March 2010), AMED (1985 to March 2010), Web of Science (2000 to March 2010) and LILACS (1982 to March 2010). Randomised controlled trials involving children up to three years old with bronchiolitis comparing steam inhalation (or cool mist) or humidified oxygen against bronchodilators, corticosteroids or placebo; alone or in combination. Two review authors independently assessed trial quality and extracted data. Only one study (156 children aged between seven weeks and 24 months with signs and symptoms of bronchiolitis) met the eligibility criteria for inclusion. Participants were randomised into three groups: nebulised salbutamol, nebulised saline and mist in a tent. The results showed a significant decrease in respiratory distress symptom (RDS) score in the nebulised salbutamol group but no significant decrease in the RDS score in the mist in a tent or nebulised saline groups. The study did not report on adverse effects of the interventions. Steam inhalation (or cool mist therapy) is commonly used to treat acute bronchiolitis in resource-constrained settings. One study was eligible for inclusion and found that nebulised salbutamol was an effective intervention for young children with bronchiolitis but mist in a tent did not lead to a significant decrease in RDS score. Since only one study was analysed it would be misleading to conclude that mist therapy is ineffective in children with bronchiolitis. We conclude that there is insufficient evidence to inform practice regarding using steam inhalation or mist therapy for acute bronchiolitis in children up to three years old.

Cryo Tank Fill at Pad 39B

NASA Image and Video Library

2017-09-26

Mist or vapor is visible as a Praxair truck slowly transfers its load of liquid oxygen, or LO2, into a giant storage sphere at the northwest corner of Launch Pad 39B at NASA's Kennedy Space Center in Florida. The sphere will gradually be chilled down from normal temperature to about negative 298 degrees Fahrenheit, during the first major integrated operation to prepare for the launch of the agency's Orion spacecraft atop the Space Launch System (SLS) rocket. The Ground Systems Development and Operations Program is overseeing upgrades and modifications to pad B to support the launch of the SLS and Orion spacecraft for Exploration Mission-1, deep space missions and NASA’s journey to Mars.

Water Mist fire suppression experiment

NASA Technical Reports Server (NTRS)

2001-01-01

The Water Mist commercial research program is scheduled to fly an investigation on STS-107 in 2002. This investigation will be flown as an Experimental Mounting Structure (EMS) insert into the updated Combustion Module (CM-2), a sophisticated combustion chamber plus diagnostic equipment. (The investigation hardware is shown here mounted in a non-flight frame similar to the EMS.) Water Mist is a commercial research program by the Center for Commercial Applications of Combustion in Space (CCACS), a NASA Commercial Space Center located at the Colorado School of Mines, in Golden, CO and Industry Partner Environmental Engineering Concepts. The program is focused on developing water mist as a replacement for bromine-based chemical fire suppression agents (halons). By conducting the experiments in microgravity, interference from convection currents is minimized and fundamental knowledge can be gained. This knowledge is incorporated into models, which can be used to simulate a variety of physical environments. The immediate objective of the project is to study the effect of a fine water mist on a laminar propagating flame generated in a propane-air mixture at various equivalence ratios. The effects of droplet size and concentration on the speed of the flame front is used as a measure of the effectiveness of fire suppression in this highly controlled experimental environment.

Patterned mist deposition of tri-colour CdSe/ZnS quantum dot films toward RGB LED devices

NASA Astrophysics Data System (ADS)

Pickering, S.; Kshirsagar, A.; Ruzyllo, J.; Xu, J.

2012-06-01

In this experiment a technique of mist deposition was explored as a way to form patterned ultra-thin-films of CdSe/ZnS core/shell nanocrystalline quantum dots using colloidal solutions. The objective of this study was to investigate the feasibility of mist deposition as a patterning method for creating multicolour quantum dot light emitting diodes. Mist deposition was used to create three rows of quantum dot light emitting diodes on a single device with each row having a separate colour. The colours chosen were red, green and yellow with corresponding peak wavelengths of 620 nm, 558 nm, and 587 nm. The results obtained from this experiment show that it is possible to create multicolour devices on a single substrate. The peak brightnesses obtained in this experiment for the red, green, and yellow were 508 cd/m, 507 cd/m, and 665 cd/m, respectively. The similar LED brightness is important in display technologies using colloidal quantum dots in a precursor solution to ensure one colour does not dominate the emitted spectrum. Results obtained in-terms of brightness were superior to those achieved with inkjet deposition. This study has shown that mist deposition is a viable method for patterned deposition applied to quantum dot light emitting diode display technologies.

Effect of micro mist sauna bathing on thermoregulatory and circulatory functions and thermal sensation in humans

NASA Astrophysics Data System (ADS)

Iwase, Satoshi; Kawahara, Yuko; Nishimura, Naoki; Sugenoya, Junichi

2016-05-01

To examine the effects of micro mist sauna bathing, produced by water crushing method, we exposed ten male subjects to five cases of micro mist sauna, namely (1) room temperature (RT) 38 °C with 100 % (actually 91 %) relative humidity (RH), (2) RT 41.5 °C with 80 % (actually 81 %) RH, (3) RT 41.5 °C with 100 % (actually 96 %) RH, (4) RT 45.0 °C with 64 % (actually 61 %) RH, and (5) RT 45.0 °C with 100 % (actually 86 %) RH, and measured tympanic temperature, mean skin temperature, heart rate (HR), and cheek moisture content, as well as ratings of thermal and sweating sensation tympanic temperatures at RT 45 °C were significantly higher at 86 % RH than those at 61 % RH; however, those at RT 45 °C with 61 % RH were higher than those with 86 % RH during recovery. There were no significant differences at RT 41.5 °C between with 81 % RH and with 96 % RH. Mean skin temperature was the highest at RT 45 °C 86 % RH case, followed by at RT 41.5 °C 96 % RH, RT 45 °C 61 % RH, RT 41.5 °C 81 % RH, and finally at RT 38 °C 91 % RH. HR change showed the same order as for mean skin temperature. A significant difference in cheek moisture content was observed between RT 41.5 °C with 81 % RH and RT 45 °C with 86 % RH 10 min after the micro mist bathing. There were no significant differences between ratings of thermal sensation at RT 41.5 °C with 81 % RH and at RT 45 °C with 61 % RH and RT 45 °C with 61 % RH and RT 45 °C with 86 % RH. Between RT 45 °C with 86 % RH and RT 41.5 °C with 81 % RH, there was a tendency for interaction (0.05 < p < 0.1). Other cases showed significant higher ratings of thermal sensation at higher room temperature or higher relative humidity. The ratings of sweating sensation 10 min after the mist sauna bathing were significantly higher at higher RT and RH except between RT 41.5 °C 96 % RH and RT 45 °C 86 % RH which exhibited no significant difference. We concluded that the micro mist sauna produced by water crushing method induced more moderate and effective thermal effect during micro mist sauna bathing than the conventional mist sauna bathing. In addition, micro mist sauna is as effective for heating the human subjects as bathtub bathing as well as more moderate thermal and sweating sensations.

Use of a Terrestrial LIDAR Sensor for Drift Detection in Vineyard Spraying

PubMed Central

Gil, Emilio; Llorens, Jordi; Llop, Jordi; Fàbregas, Xavier; Gallart, Montserrat

2013-01-01

The use of a scanning Light Detection and Ranging (LIDAR) system to characterize drift during pesticide application is described. The LIDAR system is compared with an ad hoc test bench used to quantify the amount of spray liquid moving beyond the canopy. Two sprayers were used during the field test; a conventional mist blower at two air flow rates (27,507 and 34,959 m3·h−1) equipped with two different nozzle types (conventional and air injection) and a multi row sprayer with individually oriented air outlets. A simple model based on a linear function was used to predict spray deposit using LIDAR measurements and to compare with the deposits measured over the test bench. Results showed differences in the effectiveness of the LIDAR sensor depending on the sprayed droplet size (nozzle type) and air intensity. For conventional mist blower and low air flow rate; the sensor detects a greater number of drift drops obtaining a better correlation (r = 0.91; p < 0.01) than for the case of coarse droplets or high air flow rate. In the case of the multi row sprayer; drift deposition in the test bench was very poor. In general; the use of the LIDAR sensor presents an interesting and easy technique to establish the potential drift of a specific spray situation as an adequate alternative for the evaluation of drift potential. PMID:23282583

Occupational exposure to airborne contaminants during offshore oil drilling.

PubMed

Kirkhus, Niels E; Thomassen, Yngvar; Ulvestad, Bente; Woldbæk, Torill; Ellingsen, Dag G

2015-07-01

The aim was to study exposure to airborne contaminants in oil drillers during ordinary work. Personal samples were collected among 65 drill floor workers on four stationary and six moveable rigs in the Norwegian offshore sector. Air concentrations of drilling mud were determined based on measurements of the non-volatile mud components Ca and Fe. The median air concentration of mud was 140 μg m(-3). Median air concentrations of oil mist (180 μg m(-3)), oil vapour (14 mg m(-3)) and organic carbon (46 μg m(-3)) were also measured. All contaminants were detected in all work areas (drill floor, shaker area, mud pits, pump room, other areas). The highest air concentrations were measured in the shaker area, but the differences in air concentrations between working areas were moderate. Oil mist and oil vapour concentrations were statistically higher on moveable rigs than on stationary rigs, but after adjusting for differences in mud temperature the differences between rig types were no longer of statistical significance. Statistically significant positive associations were found between mud temperature and the concentrations of oil mist (Spearman's R = 0.46) and oil vapour (0.39), and between viscosity of base oil and oil mist concentrations. Use of pressure washers was associated with higher air concentrations of mud. A series of 18 parallel stationary samples showed a high and statistically significant association between concentrations of organic carbon and oil mist (r = 0.98). This study shows that workers are exposed to airborne non-volatilized mud components. Air concentrations of volatile mud components like oil mist and oil vapour were low, but were present in all the studied working areas.

A Decade in the MIST: Learnings from Investigations of Drug Metabolites in Drug Development under the "Metabolites in Safety Testing" Regulatory Guidance.

PubMed

Schadt, Simone; Bister, Bojan; Chowdhury, Swapan K; Funk, Christoph; Hop, Cornelis E C A; Humphreys, W Griffith; Igarashi, Fumihiko; James, Alexander D; Kagan, Mark; Khojasteh, S Cyrus; Nedderman, Angus N R; Prakash, Chandra; Runge, Frank; Scheible, Holger; Spracklin, Douglas K; Swart, Piet; Tse, Susanna; Yuan, Josh; Obach, R Scott

2018-06-01

Since the introduction of metabolites in safety testing (MIST) guidance by the Food and Drug Administration in 2008, major changes have occurred in the experimental methods for the identification and quantification of metabolites, ways to evaluate coverage of metabolites, and the timing of critical clinical and nonclinical studies to generate this information. In this cross-industry review, we discuss how the increased focus on human drug metabolites and their potential contribution to safety and drug-drug interactions has influenced the approaches taken by industry for the identification and quantitation of human drug metabolites. Before the MIST guidance was issued, the method of choice for generating comprehensive metabolite profile was radio chromatography. The MIST guidance increased the focus on human drug metabolites and their potential contribution to safety and drug-drug interactions and led to changes in the practices of drug metabolism scientists. In addition, the guidance suggested that human metabolism studies should also be accelerated, which has led to more frequent determination of human metabolite profiles from multiple ascending-dose clinical studies. Generating a comprehensive and quantitative profile of human metabolites has become a more urgent task. Together with technological advances, these events have led to a general shift of focus toward earlier human metabolism studies using high-resolution mass spectrometry and to a reduction in animal radiolabel absorption/distribution/metabolism/excretion studies. The changes induced by the MIST guidance are highlighted by six case studies included herein, reflecting different stages of implementation of the MIST guidance within the pharmaceutical industry. Copyright © 2018 by The American Society for Pharmacology and Experimental Therapeutics.

A novel membrane device for the removal of water vapor and water droplets from air

NASA Technical Reports Server (NTRS)

Ray, Rod; Newbold, David D.; Mccray, Scott B.; Friesen, Dwayne T.; Kliss, Mark

1992-01-01

One of the key challenges facing NASA engineers is the development of systems for separating liquids and gases in microgravity environments. In this paper, a novel membrane-based phase separator is described. This device, known as a water recovery heat exchanger (WRHEX), overcomes the inherent deficiencies of current phase-separation technology. Specifically, the WRHEX cools and removes water vapor or water droplets from feed-air streams without the use of a vacuum or centrifugal force. As is shown in this paper, only a low-power air blower and a small stream of recirculated cool water is required for WRHEX operation. This paper presents the results of tests using this novel membrane device over a wide range of operating conditions. The data show that the WRHEX produces a dry air stream containing no entrained or liquid water - even when the feed air contains water droplets or mist. An analysis of the operation of the WRHEX is presented.

Mist Interval and Hormone Concentration Influence Rooting of Florida and Piedmont Azalea

USDA-ARS?s Scientific Manuscript database

Native azalea (Rhododendron spp.) vegetative propagation information is limited. The objective of this experiment is to determine optimal levels of K-IBA and mist intervals for propagation of Florida azalea (Rhododendron austrinum) and Piedmont azalea (Rhododendron canescens). Florida azalea roote...

Water Misting and Injection of Commercial Aircraft Engines to Reduce Airport NOx

NASA Technical Reports Server (NTRS)

Daggett, David L.; Hendricks, Robert C. (Technical Monitor)

2004-01-01

This report provides the first high level look at system design, airplane performance, maintenance, and cost implications of using water misting and water injection technology in aircraft engines for takeoff and climb-out NOx emissions reduction. With an engine compressor inlet water misting rate of 2.2 percent water-to-air ratio, a 47 percent NOx reduction was calculated. Combustor water injection could achieve greater reductions of about 85 percent, but with some performance penalties. For the water misting system on days above 59 F, a fuel efficiency benefit of about 3.5 percent would be experienced. Reductions of up to 436 F in turbine inlet temperature were also estimated, which could lead to increased hot section life. A 0.61 db noise reduction will occur. A nominal airplane weight penalty of less than 360 lb (no water) was estimated for a 305 passenger airplane. The airplane system cost is initially estimated at $40.92 per takeoff giving an attractive NOx emissions reduction cost/benefit ratio of about $1,663/ton.

Comparative study of glass tube and mist chamber sampling techniques for the analysis of gaseous carbonyl compounds

NASA Astrophysics Data System (ADS)

François, Stéphanie; Perraud, Véronique; Pflieger, Maryline; Monod, Anne; Wortham, Henri

In this work, glass tube and mist chamber sampling techniques using 2,4-dinitrophenylhydrazine as derivative agent for the analysis of gaseous carbonyl compounds are compared. Trapping efficiencies of formaldehyde, acetaldehyde, propionaldehyde, acetone, acrolein, glyoxal, crotonaldehyde, benzaldehyde, butyraldehyde and valeraldehyde are experimentally determined using a gas-phase generator. In addition to generalise our results to all atmospheric gaseous compounds and derivative agents, theoretical trapping efficiencies and enrichment factors are expressed taking into account mechanisms involved in the two kinds of traps. Theoretical and experimental results show that, as expected, the trapping efficiencies of the glass tube depend mainly on solubility of compounds. The results provide new information and better understanding of phenomena occurring in the mist chamber and the ability of this sampler to concentrate the samples. Hence, the mist chamber is the more convenient sampling method when the trapping is associated to a fast derivatisation of the compounds and the glass tube technique must be used to trap atmospheric compounds without simultaneous derivatisation.

Extrinsic allergic alveolitis caused by misting fountains.

PubMed

Koschel, Dirk; Stark, Wolfram; Karmann, Fritz; Sennekamp, Jochen; Müller-Wening, Dietrich

2005-08-01

Recently, an increasing number of patients were presented to our clinics with febrile and respiratory symptoms associated with exposure to a new type of domestic ultrasonic humidifier. We report on 11 patients who developed recurrent episodes of fever, cough and dyspnea after repeated exposure to ultrasonic misting fountains at home. A diagnosis of extrinsic allergic alveolitis (EAA) or toxic alveolitis was made on the basis of the history and the clinical, radiological, laboratory and immunological findings. Eight patients were subjected to inhalative challenge tests with their own ultrasonic misting fountains, and all of them exhibited positive reactions. Nine patients were diagnosed with an EAA (humidifier lung) and two patients with a toxic alveolitis (humidifier fever). This study demonstrates the potential for ultrasonic misting fountains to cause illness in the home. In view of the increasing popularity of these devices, humidifier lung and humidifier fever should be considered in the differential diagnosis of patients with unexplained pulmonary or flu-like illnesses with fever.

Investigation of Dispersed and Dispersed Annular (rivulet or Thin Film) Flow Phase Separation in Tees.

NASA Astrophysics Data System (ADS)

McCreery, Glenn Ernest

An experimental and analytical investigation of dispersed and dispersed-annular (rivulet or thin film) flow phase separation in tees has been successfully completed. The research was directed at, but is not specific to, determining flow conditions, following a loss of coolant accident, in the large rectangular passageways leading to vacuum buildings in the containment envelope of some CANDU nuclear reactors. The primary objectives of the research were to: (1) obtain experimental data to help formulate and test mechanistic analytical models of phase separation, and (2) develop the analytical models in computer programs which predict phase separation from upstream flow and pressure conditions and downstream and side branch pressure boundary conditions. To meet these objectives an air-water experimental apparatus was constructed, and consists of large air blowers attached to a long rectangular duct leading to a tee in the horizontal plane. A variety of phenomena was investigated including, for comparison with computer predictions, air streamlines and eddy boundary geometry, drop size spectra, macroscopic mass balances, liquid rivulet pathlines, and trajectories of drops of known size and velocity. Four separate computer programs were developed to analyze phase separation. Three of the programs are used sequentially to calculate dispersed mist phase separation in a tee. The fourth is used to calculate rivulet or thin film pathlines. Macroscopic mass balances are calculated from a summation of mass balances for drops with representative sizes (and masses) spaced across the drop size spectrum. The programs are tested against experimental data, and accurately predict gas flow fields, drop trajectories, rivulet pathlines and macroscopic mass balances. In addition to development of the computer programs, analysis was performed to specify the scaling of dispersed mist and rivulet or thin film flow, to investigate pressure losses in tees, and the inter-relationship of loss coefficients, contraction coefficients, and eddy geometry. The important transient effects of liquid storage in eddies were also analyzed.

Surface Acoustic Wave Nebulisation Mass Spectrometry for the Fast and Highly Sensitive Characterisation of Synthetic Dyes in Textile Samples

NASA Astrophysics Data System (ADS)

Astefanei, Alina; van Bommel, Maarten; Corthals, Garry L.

2017-10-01

Surface acoustic wave nebulisation (SAWN) mass spectrometry (MS) is a method to generate gaseous ions compatible with direct MS of minute samples at femtomole sensitivity. To perform SAWN, acoustic waves are propagated through a LiNbO3 sampling chip, and are conducted to the liquid sample, which ultimately leads to the generation of a fine mist containing droplets of nanometre to micrometre diameter. Through fission and evaporation, the droplets undergo a phase change from liquid to gaseous analyte ions in a non-destructive manner. We have developed SAWN technology for the characterisation of organic colourants in textiles. It generates electrospray-ionisation-like ions in a non-destructive manner during ionisation, as can be observed by the unmodified chemical structure. The sample size is decreased by tenfold to 1000-fold when compared with currently used liquid chromatography-MS methods, with equal or better sensitivity. This work underscores SAWN-MS as an ideal tool for molecular analysis of art objects as it is non-destructive, is rapid, involves minimally invasive sampling and is more sensitive than current MS-based methods. [Figure not available: see fulltext.

Industry and Public Sector Cooperation for Information Sharing: Ports of the Puget Sound

DTIC Science & Technology

2009-07-01

describes the effectiveness of key relationships 25. Establish a sustainable funding model (repeatable, 2x yearly) 26. Continue to improve MIST...effectiveness of key relationships 25. Establish a sustainable funding model (repeatable, 2x yearly) Lessons learned about MIST processes In this

Effect of drilling fluid systems and temperature on oil mist and vapour levels generated from shale shaker.

PubMed

Steinsvåg, Kjersti; Galea, Karen S; Krüger, Kirsti; Peikli, Vegard; Sánchez-Jiménez, Araceli; Sætvedt, Esther; Searl, Alison; Cherrie, John W; van Tongeren, Martie

2011-05-01

Workers in the drilling section of the offshore petroleum industry are exposed to air pollutants generated by drilling fluids. Oil mist and oil vapour concentrations have been measured in the drilling fluid processing areas for decades; however, little work has been carried out to investigate exposure determinants such as drilling fluid viscosity and temperature. A study was undertaken to investigate the effect of two different oil-based drilling fluid systems and their temperature on oil mist, oil vapour, and total volatile organic compounds (TVOC) levels in a simulated shale shaker room at a purpose-built test centre. Oil mist and oil vapour concentrations were sampled simultaneously using a sampling arrangement consisting of a Millipore closed cassette loaded with glass fibre and cellulose acetate filters attached to a backup charcoal tube. TVOCs were measured by a PhoCheck photo-ionization detector direct reading instrument. Concentrations of oil mist, oil vapour, and TVOC in the atmosphere surrounding the shale shaker were assessed during three separate test periods. Two oil-based drilling fluids, denoted 'System 2.0' and 'System 3.5', containing base oils with a viscosity of 2.0 and 3.3-3.7 mm(2) s(-1) at 40°C, respectively, were used at temperatures ranging from 40 to 75°C. In general, the System 2.0 yielded low oil mist levels, but high oil vapour concentrations, while the opposite was found for the System 3.5. Statistical significant differences between the drilling fluid systems were found for oil mist (P = 0.025),vapour (P < 0.001), and TVOC (P = 0.011). Increasing temperature increased the oil mist, oil vapour, and TVOC levels. Oil vapour levels at the test facility exceeded the Norwegian oil vapour occupational exposure limit (OEL) of 30 mg m(-3) when the drilling fluid temperature was ≥50°C. The practice of testing compliance of oil vapour exposure from drilling fluids systems containing base oils with viscosity of ≤2.0 mm(2) s(-1) at 40°C against the Norwegian oil vapour OEL is questioned since these base oils are very similar to white spirit. To reduce exposures, relevant technical control measures in this area are to cool the drilling fluid <50°C before it enters the shale shaker units, enclose shale shakers and related equipment, in addition to careful consideration of which fluid system to use.

Instruction Workbook for Tracheostomy Suctioning and Misting in a School Setting.

ERIC Educational Resources Information Center

Wolf, Karen McKinney; Roach, Antionette Andolfatto

The handbook presents California guidelines for training school personnel to provide skilled nursing procedures such as tracheostomy suctioning and misting for students with special health needs. The workbook begins with an overview of the anatomy and function of the respiratory system, specifically breathing mechanics. Part 2 considers the…

42 CFR 84.1140 - Dust, fume, and mist respirators; performance requirements; general.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Dust, fume, and mist respirators; performance requirements; general. 84.1140 Section 84.1140 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY...

42 CFR 84.1140 - Dust, fume, and mist respirators; performance requirements; general.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Dust, fume, and mist respirators; performance requirements; general. 84.1140 Section 84.1140 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY...

42 CFR 84.1140 - Dust, fume, and mist respirators; performance requirements; general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Dust, fume, and mist respirators; performance requirements; general. 84.1140 Section 84.1140 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY...

42 CFR 84.1140 - Dust, fume, and mist respirators; performance requirements; general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Dust, fume, and mist respirators; performance requirements; general. 84.1140 Section 84.1140 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY...

42 CFR 84.1140 - Dust, fume, and mist respirators; performance requirements; general.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Dust, fume, and mist respirators; performance requirements; general. 84.1140 Section 84.1140 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY...

Vegetative Propagation of Aspen by Greenwood Cuttings

Treesearch

Robert E. Farmer

1963-01-01

Greenwood stem cuttings taken from root suckers of Populus tremuloides and P. grandidentata were rooted in coarse sand under both intermittent mist and polyethylene sheeting in a greenhouse and under mist in an outdoor propagation bed. Prerooting treatment of cuttings with aqueous solutions of lBA (20-100 p.p.m. ) stimulated...

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

30 CFR 70.305 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-UNDERGROUND COAL MINES Respiratory Equipment § 70.305 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by...

Industry and Public Sector Cooperation for Information Sharing: Port of Honolulu

DTIC Science & Technology

2010-01-01

The CIC also provided coffee and pastries both days of MIST. Food has been a challenge for MIST. The team is well aware when food is provided...participants appear to feel more comfortable. We have regularly observed participants gathered around the coffee or pastry table furthering

Cryo Tank Fill at Pad 39B

NASA Image and Video Library

2017-09-26

A large plume of mist or vapor is visible as a Praxair truck slowly transfers its load of liquid oxygen, or LO2, into a giant storage sphere at the northwest corner of Launch Pad 39B at NASA's Kennedy Space Center in Florida. The sphere will gradually be chilled down from normal temperature to about negative 298 degrees Fahrenheit, during the first major integrated operation to prepare for the launch of the agency's Orion spacecraft atop the Space Launch System (SLS) rocket. The Ground Systems Development and Operations Program is overseeing upgrades and modifications to pad B to support the launch of the SLS and Orion spacecraft for Exploration Mission-1, deep space missions and NASA’s journey to Mars.

Decontamination formulation with additive for enhanced mold remediation

DOEpatents

Tucker, Mark D [Albuquerque, NM; Irvine, Kevin [Huntsville, AL; Berger, Paul [Rome, NY; Comstock, Robert [Bel Air, MD

2010-02-16

Decontamination formulations with an additive for enhancing mold remediation. The formulations include a solubilizing agent (e.g., a cationic surfactant), a reactive compound (e.g., hydrogen peroxide), a carbonate or bicarbonate salt, a water-soluble bleaching activator (e.g., propylene glycol diacetate or glycerol diacetate), a mold remediation enhancer containing Fe or Mn, and water. The concentration of Fe.sup.2+ or Mn.sup.2+ ions in the aqueous mixture is in the range of about 0.0001% to about 0.001%. The enhanced formulations can be delivered, for example, as a foam, spray, liquid, fog, mist, or aerosol for neutralization of chemical compounds, and for killing certain biological compounds or agents and mold spores, on contaminated surfaces and materials.

NASA Tech Briefs, January 2010

NASA Technical Reports Server (NTRS)

2010-01-01

Topics covered include: Cryogenic Flow Sensor; Multi-Sensor Mud Detection; Gas Flow Detection System; Mapping Capacitive Coupling Among Pixels in a Sensor Array; Fiber-Based Laser Transmitter for Oxygen A-Band Spectroscopy and Remote Sensing; Low-Profile, Dual-Wavelength, Dual-Polarized Antenna; Time-Separating Heating and Sensor Functions of Thermistors in Precision Thermal Control Applications; Cellular Reflectarray Antenna; A One-Dimensional Synthetic-Aperture Microwave Radiometer; Electrical Switching of Perovskite Thin-Film Resistors; Two-Dimensional Synthetic-Aperture Radiometer; Ethernet-Enabled Power and Communication Module for Embedded Processors; Electrically Variable Resistive Memory Devices; Improved Attachment in a Hybrid Inflatable Pressure Vessel; Electrostatic Separator for Beneficiation of Lunar Soil; Amorphous Rover; Space-Frame Antenna; Gear-Driven Turnbuckle Actuator; In-Situ Focusing Inside a Thermal Vacuum Chamber; Space-Frame Lunar Lander; Wider-Opening Dewar Flasks for Cryogenic Storage; Silicon Oxycarbide Aerogels for High-Temperature Thermal Insulation; Supercapacitor Electrolyte Solvents with Liquid Range Below -80 C; Designs and Materials for Better Coronagraph Occulting Masks; Fuel-Cell-Powered Vehicle with Hybrid Power Management; Fine-Water-Mist Multiple-Orientation-Discharge Fire Extinguisher; Fuel-Cell Water Separator; Turbulence and the Stabilization Principle; Improved Cloud Condensation Nucleus Spectrometer; Better Modeling of Electrostatic Discharge in an Insulator; Sub-Aperture Interferometers; Terahertz Mapping of Microstructure and Thickness Variations; Multiparallel Three-Dimensional Optical Microscopy; Stabilization of Phase of a Sinusoidal Signal Transmitted Over Optical Fiber; Vacuum-Compatible Wideband White Light and Laser Combiner Source System; Optical Tapers as White-Light WGM Resonators; EPR Imaging at a Few Megahertz Using SQUID Detectors; Reducing Field Distortion in Magnetic Resonance Imaging; Fluorogenic Cell-Based Biosensors for Monitoring Microbes; A Constant-Force Resistive Exercise Unit; GUI to Facilitate Research on Biological Damage from Radiation; On-Demand Urine Analyzer; More-Realistic Digital Modeling of a Human Body; and Advanced Liquid-Cooling Garment Using Highly Thermally Conductive Sheets.

Studies on remote sensing method of particle size and water density distribution in mists and clouds using laser radar techniques

NASA Technical Reports Server (NTRS)

Shimizu, H.; Kobayasi, T.; Inaba, H.

1979-01-01

A method of remote measurement of the particle size and density distribution of water droplets was developed. In this method, the size of droplets is measured from the Mie scattering parameter which is defined as the total-to-backscattering ratio of the laser beam. The water density distribution is obtained by a combination of the Mie scattering parameter and the extinction coefficient of the laser beam. This method was examined experimentally for the mist generated by an ultrasonic mist generator and applied to clouds containing rain and snow. Compared with the conventional sampling method, the present method has advantages of remote measurement capability and improvement in accuracy.

Increasing mist net captures of migrant Northern Saw-whet Owls (Aegolius acadicus) with an audiolure

Treesearch

Thomas C. Erdman; David F. Brinker

1997-01-01

In 1986, an "audiolure" was developed and tested at the Little Suamico Ornithological Station near Green Bay, Wisconsin. The audiolure consisted of broadcast amplified "solicitation" calls of Northern Saw-whet Owls (Aegolius acadicus) normally associated with courtship activities. From 1971 through 1985, using passive mist netting...

Improving Freight Fire Safety: Analysis and Testing of Real Engine Conditions to Progress Development of Mist-controlling Additives for Fire Mitigation

DOT National Transportation Integrated Search

2009-12-01

The formation of a fuel mist resulting from high shear stresses acting on the fuel during violent sloshing and tank rupture under the energy of a crash severely increases the occurrence and intensity of fires in transportation related accidents. In o...

RESPONSE OF BUSH BEAN EXPOSED TO ACID MIST

EPA Science Inventory

Bush bean plants (Phaseolus vulgaris L. cv. Contender) were treated once a week for six weeks with simulated acid mist at five pH ranging from 5.5 to 2.0. Leaf injury developed on plants exposed to acid concentrations below pH 3 and many leaves developed a flecking symptom simila...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Code of Federal Regulations, 2013 CFR

2013-10-01

... Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist... 42 Public Health 1 2013-10-01 2013-10-01 false Isoamyl acetate tightness test; dust, fume, and...

42 CFR 84.1146 - Lead fume test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Lead fume test for dust, fume, and mist respirators; minimum requirements. 84.1146 Section 84.1146 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1143 - Dust, fume, and mist air-purifying filter tests; performance requirements; general.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Dust, fume, and mist air-purifying filter tests; performance requirements; general. 84.1143 Section 84.1143 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Code of Federal Regulations, 2010 CFR

2010-10-01

... Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist... 42 Public Health 1 2010-10-01 2010-10-01 false Isoamyl acetate tightness test; dust, fume, and...

42 CFR 84.1158 - Dust, fume, and mist tests; respirators with filters; minimum requirements; general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Dust, fume, and mist tests; respirators with filters; minimum requirements; general. 84.1158 Section 84.1158 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES...

42 CFR 84.1149 - Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements. 84.1149 Section 84.1149 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1143 - Dust, fume, and mist air-purifying filter tests; performance requirements; general.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Dust, fume, and mist air-purifying filter tests; performance requirements; general. 84.1143 Section 84.1143 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1149 - Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements. 84.1149 Section 84.1149 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1143 - Dust, fume, and mist air-purifying filter tests; performance requirements; general.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Dust, fume, and mist air-purifying filter tests; performance requirements; general. 84.1143 Section 84.1143 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1151 - DOP filter test; respirators designed as respiratory protection against dusts, fumes, and mists...

Code of Federal Regulations, 2013 CFR

2013-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2013-10-01 2013-10-01 false DOP filter test; respirators designed as...

42 CFR 84.1151 - DOP filter test; respirators designed as respiratory protection against dusts, fumes, and mists...

Code of Federal Regulations, 2014 CFR

2014-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2014-10-01 2014-10-01 false DOP filter test; respirators designed as...

42 CFR 84.1143 - Dust, fume, and mist air-purifying filter tests; performance requirements; general.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Dust, fume, and mist air-purifying filter tests; performance requirements; general. 84.1143 Section 84.1143 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1151 - DOP filter test; respirators designed as respiratory protection against dusts, fumes, and mists...

Code of Federal Regulations, 2012 CFR

2012-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2012-10-01 2012-10-01 false DOP filter test; respirators designed as...

42 CFR 84.1158 - Dust, fume, and mist tests; respirators with filters; minimum requirements; general.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Dust, fume, and mist tests; respirators with filters; minimum requirements; general. 84.1158 Section 84.1158 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES...

42 CFR 84.1149 - Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements. 84.1149 Section 84.1149 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1158 - Dust, fume, and mist tests; respirators with filters; minimum requirements; general.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Dust, fume, and mist tests; respirators with filters; minimum requirements; general. 84.1158 Section 84.1158 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Code of Federal Regulations, 2014 CFR

2014-10-01

... Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist... 42 Public Health 1 2014-10-01 2014-10-01 false Isoamyl acetate tightness test; dust, fume, and...

42 CFR 84.1146 - Lead fume test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Lead fume test for dust, fume, and mist respirators; minimum requirements. 84.1146 Section 84.1146 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1143 - Dust, fume, and mist air-purifying filter tests; performance requirements; general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Dust, fume, and mist air-purifying filter tests; performance requirements; general. 84.1143 Section 84.1143 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1151 - DOP filter test; respirators designed as respiratory protection against dusts, fumes, and mists...

Code of Federal Regulations, 2010 CFR

2010-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2010-10-01 2010-10-01 false DOP filter test; respirators designed as...

42 CFR 84.1158 - Dust, fume, and mist tests; respirators with filters; minimum requirements; general.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Dust, fume, and mist tests; respirators with filters; minimum requirements; general. 84.1158 Section 84.1158 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Code of Federal Regulations, 2012 CFR

2012-10-01

... Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist... 42 Public Health 1 2012-10-01 2012-10-01 false Isoamyl acetate tightness test; dust, fume, and...

42 CFR 84.1149 - Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements. 84.1149 Section 84.1149 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1146 - Lead fume test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Lead fume test for dust, fume, and mist respirators; minimum requirements. 84.1146 Section 84.1146 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1146 - Lead fume test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Lead fume test for dust, fume, and mist respirators; minimum requirements. 84.1146 Section 84.1146 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1158 - Dust, fume, and mist tests; respirators with filters; minimum requirements; general.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Dust, fume, and mist tests; respirators with filters; minimum requirements; general. 84.1158 Section 84.1158 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES...

42 CFR 84.1149 - Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Airflow resistance tests; all dust, fume, and mist respirators; minimum requirements. 84.1149 Section 84.1149 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1151 - DOP filter test; respirators designed as respiratory protection against dusts, fumes, and mists...

Code of Federal Regulations, 2011 CFR

2011-10-01

... Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide... 42 Public Health 1 2011-10-01 2011-10-01 false DOP filter test; respirators designed as...

42 CFR 84.1146 - Lead fume test for dust, fume, and mist respirators; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Lead fume test for dust, fume, and mist respirators; minimum requirements. 84.1146 Section 84.1146 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF...

42 CFR 84.1141 - Isoamyl acetate tightness test; dust, fume, and mist respirators designed for respiratory...

Code of Federal Regulations, 2011 CFR

2011-10-01

... Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist... 42 Public Health 1 2011-10-01 2011-10-01 false Isoamyl acetate tightness test; dust, fume, and...

Field evaluations of residual pesticide applications and misting system on militarily relevant materials against medically important mosquitoes in Thailand

USDA-ARS?s Scientific Manuscript database

A key strategy to reduce insect-borne disease is to reduce contact between disease vectors and hosts. In the current study, residual pesticide application and misting system were applied on militarily relevant materials and evaluated against medically important mosquitoes. Field evaluations were car...

30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

Code of Federal Regulations, 2014 CFR

2014-07-01

... gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND... limit values adopted by the American Conference of Governmental Industrial Hygienists in “Threshold...

30 CFR 72.701 - Respiratory equipment; gas, dusts, fumes, or mists.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Respiratory equipment; gas, dusts, fumes, or... LABOR COAL MINE SAFETY AND HEALTH HEALTH STANDARDS FOR COAL MINES Miscellaneous § 72.701 Respiratory equipment; gas, dusts, fumes, or mists. Respiratory equipment approved by NIOSH under 42 CFR part 84 shall...

Improving Freight Fire Safety: Assessment of the Effectiveness of Mist-Controlling Additives for Mitigating Crash-Induced Diesel Fires

DOT National Transportation Integrated Search

2009-12-01

Adding long chained polymers to diesel has been proposed as a method to prevent crash fires by arresting the breakup of diesel fuel into a fine mist in transportation related accidents. The effect of such additives on the flow properties of diesel wa...

Humidification of Blow-By Oxygen During Recovery of Postoperative Pediatric Patients: One Unit's Journey.

PubMed

Donahue, Suzanne; DiBlasi, Robert M; Thomas, Karen

2018-02-02

To examine the practice of nebulizer cool mist blow-by oxygen administered to spontaneously breathing postanesthesia care unit (PACU) pediatric patients during Phase one recovery. Existing evidence was evaluated. Informal benchmarking documented practices in peer organizations. An in vitro study was then conducted to simulate clinical practice and determine depth and amount of airway humidity delivery with blow-by oxygen. Informal benchmarking information was obtained by telephone interview. Using a three-dimensional printed simulation model of the head connected to a breathing lung simulator, depth and amount of moisture delivery in the respiratory tree were measured. Evidence specific to PACU administration of cool mist blow-by oxygen was limited. Informal benchmarking revealed that routine cool mist oxygenated blow-by administration was not widely practiced. The laboratory experiment revealed minimal moisture reaching the mid-tracheal area of the simulated airway model. Routine use of oxygenated cool mist in spontaneously breathing pediatric PACU patients is not supported. Copyright © 2017 American Society of PeriAnesthesia Nurses. Published by Elsevier Inc. All rights reserved.

ATLANTIC BIRDS: a data set of bird species from the Brazilian Atlantic Forest.

PubMed

Hasui, Érica; Metzger, Jean Paul; Pimentel, Rafael G; Silveira, Luís Fábio; Bovo, Alex A D A; Martensen, Alexandre C; Uezu, Alexandre; Regolin, André L; Bispo de Oliveira, Arthur Â; Gatto, Cassiano A F R; Duca, Charles; Andretti, Christian B; Banks-Leite, Cristina; Luz, Daniela; Mariz, Daniele; Alexandrino, Eduardo R; de Barros, Fabio M; Martello, Felipe; Pereira, Iolanda M D S; da Silva, José N; Ferraz, Katia M P M D B; Naka, Luciano N; Dos Anjos, Luiz; Efe, Márcio A; Pizo, Marco Aurélio; Pichorim, Mauro; Gonçalves, Maycon Sanyvan S; Cordeiro, Paulo Henrique Chaves; Dias, Rafael A; Muylaert, Renata D L; Rodrigues, Rodolpho C; da Costa, Thiago V V; Cavarzere, Vagner; Tonetti, Vinicius R; Silva, Wesley R; Jenkins, Clinton N; Galetti, Mauro; Ribeiro, Milton C

2018-02-01

South America holds 30% of the world's avifauna, with the Atlantic Forest representing one of the richest regions of the Neotropics. Here we have compiled a data set on Brazilian Atlantic Forest bird occurrence (150,423) and abundance samples (N = 832 bird species; 33,119 bird individuals) using multiple methods, including qualitative surveys, mist nets, point counts, and line transects). We used four main sources of data: museum collections, on-line databases, literature sources, and unpublished reports. The data set comprises 4,122 localities and data from 1815 to 2017. Most studies were conducted in the Florestas de Interior (1,510 localities) and Serra do Mar (1,280 localities) biogeographic sub-regions. Considering the three main quantitative methods (mist net, point count, and line transect), we compiled abundance data for 745 species in 576 communities. In the data set, the most frequent species were Basileuterus culicivorus, Cyclaris gujanensis, and Conophaga lineata. There were 71 singletons, such as Lipaugus conditus and Calyptura cristata. We suggest that this small number of records reinforces the critical situation of these taxa in the Atlantic Forest. The information provided in this data set can be used for macroecological studies and to foster conservation strategies in this biodiversity hotspot. No copyright restrictions are associated with the data set. Please cite this Data Paper if data are used in publications and teaching events. © 2017 by the Ecological Society of America.

Perfluoroalkyl Substance Serum Concentrations and Immune Response to FluMist Vaccination among Healthy Adults

PubMed Central

Stein, Cheryl R; Ge, Yongchao; Wolff, Mary S; Ye, Xiaoyun; Calafat, Antonia M; Kraus, Thomas; Moran, Thomas M

2016-01-01

Perfluoroalkyl substances (PFAS) were shown to be immunotoxic in laboratory animals. There is some epidemiological evidence that PFAS exposure is inversely associated with vaccine-induced antibody concentration. We examined immune response to vaccination with FluMist intranasal live attenuated influenza vaccine in relation to four PFAS (perfluorooctanoate, perfluorononanoate, perfluorooctane sulfonate, perfluorohexane sulfonate) serum concentrations among 78 healthy adults vaccinated during the 2010 – 2011 influenza season. We measured anti-A H1N1 antibody response and cytokine and chemokine concentrations in serum pre-vaccination, 3 days post-vaccination, and 30 days post-vaccination. We measured cytokine, chemokine, and mucosal IgA concentration in nasal secretions 3 days post-vaccination and 30 days post-vaccination. Adults with higher PFAS concentrations were more likely to seroconvert after FluMist vaccination as compared to adults with lower PFAS concentrations. The associations, however, were imprecise and few participants seroconverted as measured either by hemagglutination inhibition (9%) or immunohistochemical staining (25%). We observed no readily discernable or consistent pattern between PFAS concentration and baseline cytokine, chemokine, or mucosal IgA concentration, or between PFAS concentration and change in these immune markers between baseline and FluMist-response states. The resuts of this study do not support a reduced immune response to FluMist vaccination among healthy adults in relation to serum PFAS concentration. Given the study’s many limitations, however, it does not rule out impaired vaccine response to other vaccines or vaccine components in either children or adults. PMID:27208468

Developing Standards to Qualify a Fine Water Mist Fire Extinguisher for Human Spaceflight

NASA Technical Reports Server (NTRS)

Graf, John

2011-01-01

NASA is developing a Fine Water Mist Portable Fire Extinguisher for use on the International Space Station. The International Space Station presently uses two different types of fire extinguishers: a water foam extinguisher in the Russian Segment, and a carbon dioxide extinguisher in the US Segment and Columbus and Kibo pressurized elements. Changes in emergency breathing equipment make Fine Water Mist operationally preferable. Supplied oxygen breathing systems allow for safe discharge of a carbon dioxide fire extinguisher, without concerns of the crew inhaling unsafe levels of carbon dioxide. But the Portable Breathing Apparatus offers no more than 15 minutes of capability, and continued use of hose based supplied oxygen systems increases the oxygen content in a fire situation. NASA has developed a filtering respirator cartridge for use in a fire environment. It is qualified to provide up to 90 minutes of capability, and because it is a filtering respirator it does not add oxygen to the environment. The fire response respirator cartridge does not filter carbon dioxide, so a crew member discharging a CO2 fire extinguisher while wearing this filtering respirator would be at risk of inhaling unsafe levels of CO2. Fine Water Mist extinguishes a fire without creating a large volume of air with reduced oxygen and elevated CO2. Compared to the carbon dioxide based Portable Fire Extinguisher, the flight qualification of Fine Water Mist systems requires special care. Qualification of the CO2 based Portable Fire Extinguisher began with the assumption that any fire on ISS would be extinguished if the air in the fire environment reached a critical concentration of CO2. Qualification of a CO2 based system requires the developers to make assertions and assumptions about vehicle geometry and the ability of the extinguisher to deliver CO2 in different geometric configurations, but the developers did not need to make assertions or assumptions about the size of the fire, the temperature, or the heat generation rate. Fine Water Mist systems extinguish a fire predominantly by removing heat -- so qualification standards must evaluate geometry, but also temperature, heat transfer, and heat generation rate. This paper outlines and describes the methods used to develop standards used to qualify Fine Water Mist systems for a human spaceflight environment.

Mist and water condensation inside incubators reduce the efficacy of phototherapy.

PubMed

de Carvalho, Manoel; Torrao, Carolina Turano; Moreira, Maria Elisabeth Lopes

2011-03-01

To measure the irradiance in humidified incubator under three different overhead phototherapy devices. The effective irradiance of three phototherapy devices was assessed by taking a series of irradiance measurements in the illuminated field. Measurements were made with a fixed bandwidth broadband radiometer (380-530 nm). The distance between the light source and the radiometer was 35 cm for the daylight fluorescent lamp, 40 cm for the light emitting diode (LED) and 50 cm for the halogen phototherapy. A double-wall incubator was kept at 36°C and set at three different levels of humidity (60-70%, 80% and equal or above 90%). The irradiance under the overhead daylight fluorescent lamp phototherapy did not change with the increasing humidity. However, above 90% humidity, when water vapour inside the incubator was so saturated to the point of totally condensing in the incubator walls, the measured irradiance decreased 15% of the initial values with the blue LED phototherapy and 45% with the halogen spotlight phototherapy. Highly humidified incubators are frequently used to treat very low birthweight infants. Health professionals should be aware that mist and water condensation inside an incubator may significantly reduce the efficacy of treatment.

Mist net effort required to inventory a forest bat species assemblage.

Treesearch

Theodore J. Weller; Danny C. Lee

2007-01-01

Little quantitative information exists about the survey effort necessary to inventory temperate bat species assemblages. We used a bootstrap resampling lgorithm to estimate the number of mist net surveys required to capture individuals from 9 species at both study area and site levels using data collected in a forested watershed in northwestern California, USA, during...

Evaluation of mist-netting, nest-searching and other methods for monitoring demographic processes in landbird populations

Treesearch

Nadav Nur; Geoffrey R. Geupel

1993-01-01

Demographic processes (reproductive success, survival of young and adults, recruitment of young into the breeding population) are critical to monitoring and managing landbird populations. We discuss different techniques that have been used to monitor these demographic processes in landbird populations, focusing on constant-effort mist-netting (CEM). We assess whether...

Effects of Punishment Procedures on the Self-Stimulatory Behavior of an Autistic Child.

ERIC Educational Resources Information Center

Friman, Patrick C.; And Others

1984-01-01

Three punishment procedures--contingent applications of water mist, lemon juice, and vinegar--were evaluated as aversive treatment methods for a self-stimulatory behavior exhibited by a severely retarded 11-year-old male. The water mist procedure was as effective as lemon juice or vinegar, presented less physical threat to the client, and was…

42 CFR 84.1144 - Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum requirements. 84.1144 Section 84.1144 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH...

42 CFR 84.1144 - Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum requirements. 84.1144 Section 84.1144 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH...

42 CFR 84.1144 - Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum...

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum requirements. 84.1144 Section 84.1144 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH...

42 CFR 84.1144 - Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum requirements. 84.1144 Section 84.1144 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH...

42 CFR 84.1144 - Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Silica dust test for dust, fume, and mist respirators; single-use or reusable filters; minimum requirements. 84.1144 Section 84.1144 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH...

Standardization of mist net captures for quantification of avian migration

Treesearch

C. John Ralph

1976-01-01

In recent years many studies have used mist net capture data to quantify avian populations, especially during migration. Such studies have compared the species, age, and sex composition as well as the intensity and timing of migration through the seasons and at different locations (e.g. Preston, 1966; Lebermen and Clench, 1971; Stewart et al., 1973).

The Milwaukee Inventory for Styles of Trichotillomania-Child Version (MIST-C): Initial Development and Psychometric Properties

ERIC Educational Resources Information Center

Flessner, Christopher A.; Woods, Douglas W.; Franklin, Martin E.; Keuthen, Nancy J.; Piacentini, John; Cashin, Susan E.; Moore, Phoebe S.

2007-01-01

This article describes the development and initial psychometric properties of the Milwaukee Inventory for Styles of Trichotillomania-Child Version (MIST-C), a self-report scale designed to assess styles of hair pulling in children and adolescents diagnosed with trichotillomania (TTM). Using Internet sampling procedures, the authors recruited 164…

Minor isotope safeguards techniques (MIST): Analysis and visualization of gas centrifuge enrichment plant process data using the MSTAR model

NASA Astrophysics Data System (ADS)

Shephard, Adam M.; Thomas, Benjamin R.; Coble, Jamie B.; Wood, Houston G.

2018-05-01

This paper presents a development related to the use of minor isotope safeguards techniques (MIST) and the MSTAR cascade model as it relates to the application of international nuclear safeguards at gas centrifuge enrichment plants (GCEPs). The product of this paper is a derivation of the universal and dimensionless MSTAR cascade model. The new model can be used to calculate the minor uranium isotope concentrations in GCEP product and tails streams or to analyze, visualize, and interpret GCEP process data as part of MIST. Applications of the new model include the detection of undeclared feed and withdrawal streams at GCEPs when used in conjunction with UF6 sampling and/or other isotopic measurement techniques.

Prevalence and risk factors of non-carious cervical lesions related to occupational exposure to acid mists.

PubMed

Bomfim, Rafael Aiello; Crosato, Edgard; Mazzilli, Luiz Eugênio Nigro; Frias, Antonio Carlos

2015-01-01

This study evaluates the prevalence and risk factors of non-carious cervical lesions (NCCLs) in a Brazilian population of workers exposed and non-exposed to acid mists and chemical products. One hundred workers (46 exposed and 54 non-exposed) were evaluated in a Centro de Referência em Saúde do Trabalhador - CEREST (Worker's Health Reference Center). The workers responded to questionnaires regarding their personal information and about alcohol consumption and tobacco use. A clinical examination was conducted to evaluate the presence of NCCLs, according to WHO parameters. Statistical analyses were performed by unconditional logistic regression and multiple linear regression, with the critical level of p < 0.05. NCCLs were significantly associated with age groups (18-34, 35-44, 45-68 years). The unconditional logistic regression showed that the presence of NCCLs was better explained by age group (OR = 4.04; CI 95% 1.77-9.22) and occupational exposure to acid mists and chemical products (OR = 3.84; CI 95% 1.10-13.49), whereas the linear multiple regression revealed that NCCLs were better explained by years of smoking (p = 0.01) and age group (p = 0.04). The prevalence of NCCLs in the study population was particularly high (76.84%), and the risk factors for NCCLs were age, exposure to acid mists and smoking habit. Controlling risk factors through preventive and educative measures, allied to the use of personal protective equipment to prevent the occupational exposure to acid mists, may contribute to minimizing the prevalence of NCCLs.

Perfluoroalkyl substance serum concentrations and immune response to FluMist vaccination among healthy adults.

PubMed

Stein, Cheryl R; Ge, Yongchao; Wolff, Mary S; Ye, Xiaoyun; Calafat, Antonia M; Kraus, Thomas; Moran, Thomas M

2016-08-01

Perfluoroalkyl substances (PFAS) were shown to be immunotoxic in laboratory animals. There is some epidemiological evidence that PFAS exposure is inversely associated with vaccine-induced antibody concentration. We examined immune response to vaccination with FluMist intranasal live attenuated influenza vaccine in relation to four PFAS (perfluorooctanoate, perfluorononanoate, perfluorooctane sulfonate, perfluorohexane sulfonate) serum concentrations among 78 healthy adults vaccinated during the 2010-2011 influenza season. We measured anti-A H1N1 antibody response and cytokine and chemokine concentrations in serum pre-vaccination, 3 days post-vaccination, and 30 days post-vaccination. We measured cytokine, chemokine, and mucosal IgA concentration in nasal secretions 3 days post-vaccination and 30 days post-vaccination. Adults with higher PFAS concentrations were more likely to seroconvert after FluMist vaccination as compared to adults with lower PFAS concentrations. The associations, however, were imprecise and few participants seroconverted as measured either by hemagglutination inhibition (9%) or immunohistochemical staining (25%). We observed no readily discernable or consistent pattern between PFAS concentration and baseline cytokine, chemokine, or mucosal IgA concentration, or between PFAS concentration and change in these immune markers between baseline and FluMist-response states. The results of this study do not support a reduced immune response to FluMist vaccination among healthy adults in relation to serum PFAS concentration. Given the study's many limitations, however, it does not rule out impaired vaccine response to other vaccines or vaccine components in either children or adults. Copyright © 2016 Elsevier Inc. All rights reserved.

M-TeX and MIST Experiments Launched from Alaska

NASA Image and Video Library

2017-12-08

Caption: Composite shot of all four rockets for the M-TeX and MIST experiments is made up of 30 second exposures. The rocket salvo began at 4:13 a.m. EST, Jan. 26, 2015, from the Poker Flat Research Range, Alaska. Credit: NASA/Jamie Adkins More info: The Mesosphere-Lower Thermosphere Turbulence Experiment, or M-TeX, and the Mesospheric Inversion-layer Stratified Turbulence, or MIST, experiment were successfully conducted the morning of Jan. 26, 2015, from the Poker Flat Research Range, Alaska. The first M-Tex rocket, a NASA Terrier-Improved Malemute sounding rocket, was launched at 4:13 a.m. EST and was followed one-minute later by the first MIST experiment payload on a NASA Terrier-Improved Orion. The second M-TeX payload was launched at 4:46 a.m. EST and also was followed one minute later by the second MIST payload. Preliminary data show that all four payloads worked as planned and the trimethyl aluminum, or TMA, vapor trails were seen at the various land-based observation sites in Alaska. A fifth rocket carrying the Auroral Spatial Structures Probe remains ready on the launch pad. The launch window for this experiment runs through Jan. 27. NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Investigating the chemical mist deposition technique for poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) on textured crystalline-silicon for organic/crystalline-silicon heterojunction solar cells

NASA Astrophysics Data System (ADS)

Hossain, Jaker; Ohki, Tatsuya; Ichikawa, Koki; Fujiyama, Kazuhiko; Ueno, Keiji; Fujii, Yasuhiko; Hanajiri, Tatsuro; Shirai, Hajime

2016-03-01

Chemical mist deposition (CMD) of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) was investigated in terms of cavitation frequency f, solvent, flow rate of nitrogen, substrate temperature Ts, and substrate dc bias Vs as variables for efficient PEDOT:PSS/crystalline silicon (c-Si) heterojunction solar cells. The high-speed-camera and differential mobility analysis characterizations revealed that the average size and flux of PEDOT:PSS mist depend on f, type of solvent, and Vs. Film deposition occurred when positive Vs was applied to the c-Si substrate at Ts of 30-40 °C, whereas no deposition of films occurred with negative Vs, implying that the film is deposited mainly from negatively charged mist. The uniform deposition of PEDOT:PSS films occurred on textured c-Si(100) substrates by adjusting Ts and Vs. The adhesion of CMD PEDOT:PSS film to c-Si was greatly enhanced by applying substrate dc bias Vs compared with that of spin-coated film. The CMD PEDOT:PSS/c-Si heterojunction solar cell devices on textured c-Si(100) in 2 × 2 cm2 exhibited a power conversion efficiency η of 11.0% with better uniformity of the solar cell parameters. Furthermore, η was increased to 12.5% by adding an AR coating layer of molybdenum oxide MoOx formed by CMD. These findings suggest that CMD with negatively charged mist has great potential for the uniform deposition of organic and inorganic materials on textured c-Si substrates by suitably adjusting Ts and Vs.

Dynamics of contracting surfactant-covered filaments

NASA Astrophysics Data System (ADS)

Kamat, Pritish; Thete, Sumeet; Xu, Qi; Basaran, Osman

2013-11-01

When drops are produced from a nozzle, a thin liquid thread connects the primary drop that is about to form to the rest of the liquid in the nozzle. Often, the thread becomes disconnected from both the primary drop and the remnant liquid mass hanging from the nozzle and thereby gives rise to a free filament. Due to surface tension, the free filament then contracts or recoils. During recoil, the filament can either contract into a single satellite droplet or break up into several small satellites. Such satellite droplets are undesirable in applications where they can, for example, cause misting in a manufacturing environment and mar product quality in ink-jet printing. In many applications, the filaments are coated with a monolayer of surfactant. In this work, we study the dynamics of contraction of slender filaments of a Newtonian fluid that are covered with a monolayer of surfactant when the surrounding fluid is a passive gas. Taking advantage of the fact that the filaments are long and slender, we use a 1D-slender-jet approximation of the governing system of equations consisting of the Navier-Stokes system and the convection-diffusion equation for surfactant transport. We solve the 1D system of equations by a finite element based numerical method.

The body grasp technique: a rapid method of removing birds from mist nets

Treesearch

C.J. Ralph

2005-01-01

Safety of birds is paramount to our efforts in monitoring birds. I describe a method that has the potential of greatly increasing the speed and safety of extracting birds from mist nets. This method involves removing the feet last, as opposed to the more traditional 'feet first' method. The "body grasp" method involves slipping the fingers around...

Acid mist and soil Ca and Al alter the mineral nutrition and physiology of red spruce

Treesearch

P.G. Schaberg; D.H. DeHayes; G.J. Hawley; G.R. Strimbeck; J.R. Cumming; P.F. Murakami; C.H. Borer

2000-01-01

We examined the effects and potential interactions of acid mist and soil solution Ca and Al treatments on foliar cation concentrations, membrane-associated Ca (mCa), ion leaching, growth, carbon exchange, and cold tolerance of red spruce (Picea rubens Sarg.) saplings. Soil solution Ca additions increased foliar Ca and Zn concentrations, and increased...

Autumn populations and movements of migrant Northern Saw-whet Owls (Aegolius acadicus) at Little Suamico, Wisconsin

Treesearch

Tom C. Erdman; Tom O. Meyer; Jerry H. Smith; Debra M. Erdman

1997-01-01

Northern Saw-whet Owls (Aegolius acadicus) were once considered a "rare" bird in Wisconsin. In the 1960's mist netting at bird-banding stations revealed Saw-whets to be a regular, uncommon migrant. Passive mist netting was initiated at the Little Suamico Ornithological Station in 1971. Our Saw-whet Owl experiences were similar to other...

Evaluation of the Hamburg Rut Tester and Moisture Induced Stress Test (MIST) for field control of hot mix asphalt (HMA) in Oklahoma : final report.

DOT National Transportation Integrated Search

2013-03-01

This report covers the evaluation of the Hamburg Loaded Wheel Rut Tester (OHD L-55) and the : Moisture Induced Stress Tester (MIST) for field control of Oklahoma HMA mixtures. OHD L-55 : was evaluated as a possible replacement for AASHTO T 283 and fo...

30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND...

30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND...

30 CFR 71.700 - Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Inhalation hazards; threshold limit values for gases, dust, fumes, mists, and vapors. 71.700 Section 71.700 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR COAL MINE SAFETY AND HEALTH MANDATORY HEALTH STANDARDS-SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND...

Development and reliability of a Motivational Interviewing Scenarios Tool for Eating Disorders (MIST-ED) using a skills-based intervention among caregivers.

PubMed

Sepulveda, Ana R; Wise, Caroline; Zabala, Maria; Todd, Gill; Treasure, Janet

2013-12-01

The aims of this study were to develop an eating disorder scenarios tool to assess the motivational interviewing (MI) skills of caregivers and evaluate the coding reliability of the instrument, and to test the sensitivity to change through a pre/post/follow-up design. The resulting Motivational Interview Scenarios Tool for Eating Disorders (MIST-ED) was administered to caregivers (n = 66) who were asked to provide oral and written responses before and after a skills-based intervention, and at a 3-month follow-up. Raters achieved excellent inter-rater reliability (intra-class correlations of 91.8% on MI adherent and 86.1% for MI non-adherent statements for written scenarios and 89.2%, and 85.3% for oral scenarios). Following the intervention, MI adherent statements increased (baseline = 9.4%, post = 61.5% and follow-up 47.2%) and non-MI adherent statements decreased (baseline = 90.6%, post = 38.5% and follow-up = 52.8%). This instrument can be used as a simple method to measure the acquisition of MI skills to improve coping and both response methods are adequate. The tool shows good sensitivity to improved skills. © 2013.

Effects of formaldehyde-enriched mists on Pseudotsuga menziesii (Mirbel) Franco and Lobaria pulmonaria (L.) Hoffm.

PubMed

Muir, P S; Shirazi, A M

1996-01-01

The atmosphere in some areas is polluted with formaldehyde (HCHO); however, little is known about effects of HCHO on plants at concentrations resembling those in polluted areas. The effects of simulated fogwater enriched with HCHO on seedlings of Pseudotsuga menziesii (Mirbel) Franco (Douglas fir) and pendants of Lobaria pulmonaria (L.) Hoffm. were assessed. Plants were treated with HCHO-enriched fog (target concentrations of 100, 500, and 1000 microm) during five 4-night mist sessions. Growth and nitrogenase activity (acetylene reduction rate) for lichens and growth and timing of bud-break for Douglas fir were monitored. Nitrogenase activity was lowest in lichens treated at the highest HCHO concentration after all but the first mist session, and it declined significantly with increasing HCHO concentration after the final mist session (R(2) = 0.60, p = 0.02). However, differences in nitrogenase activity among treatments were generally not statistically significant (most p values from ANOVAs were >/= 0.20). Formaldehyde did not affect growth of the lichens. Budbreak of Douglas firs was slightly delayed and height growth was slightly depressed with increasing HCHO concentration, although effects were not statistically significant.

Microgravity

NASA Image and Video Library

2001-10-04

The Water Mist commercial research program is scheduled to fly an investigation on STS-107 in 2002. This investigation will be flown as an Experimental Mounting Structure (EMS) insert into the updated Combustion Module (CM-2), a sophisticated combustion chamber plus diagnostic equipment. (The investigation hardware is shown here mounted in a non-flight frame similar to the EMS.) Water Mist is a commercial research program by the Center for Commercial Applications of Combustion in Space (CCACS), a NASA Commercial Space Center located at the Colorado School of Mines, in Golden, CO and Industry Partner Environmental Engineering Concepts. The program is focused on developing water mist as a replacement for bromine-based chemical fire suppression agents (halons). By conducting the experiments in microgravity, interference from convection currents is minimized and fundamental knowledge can be gained. This knowledge is incorporated into models, which can be used to simulate a variety of physical environments. The immediate objective of the project is to study the effect of a fine water mist on a laminar propagating flame generated in a propane-air mixture at various equivalence ratios. The effects of droplet size and concentration on the speed of the flame front is used as a measure of the effectiveness of fire suppression in this highly controlled experimental environment.

Wood crib fire free burning test in ISO room

NASA Astrophysics Data System (ADS)

Qiang, Xu; Griffin, Greg; Bradbury, Glenn; Dowling, Vince

2006-04-01

In the research of application potential of water mist fire suppression system for fire fighting in train luggage carriage, a series of experiments were conducted in ISO room on wood crib fire with and without water mist actuation. The results of free burn test without water mist suppression are used as reference in evaluating the efficiency of water mist suppression system. As part of the free burn test, several tests have been done under the hood of ISO room to calibrate the size of the crib fire and these tests can also be used in analyzing the wall effect in room fire hazard. In these free burning experiments, wood cribs of four sizes under the hood were tested. The temperature of crib fire, heat flux around the fire, gas concentration in hood of ISO room were measured in the experiments and two sets of thermal imaging system were used to get the temperature distribution and the typical shape of the free burning flames. From the experiments, the radiation intensity in specific positions around the fire, the effective heat of combustion, mass loss, oxygen consumption rate for different sizes of fire, typical structure of the flame and self extinguishment time was obtained for each crib size.

Cryo Tank Fill at Pad 39B

NASA Image and Video Library

2017-09-26

Several Praxair trucks carrying their loads of liquid oxygen, or LO2, have arrived at Launch Pad 39B at NASA's Kennedy Space Center in Florida. A mist is visible as LO2 is offloaded from one of the trucks into the giant storage sphere located at the northwest corner of the pad has begun. The sphere will gradually be chilled down from normal temperature to about negative 298 degrees Fahrenheit, during the first major integrated operation to prepare for the launch of the agency's Orion spacecraft atop the Space Launch System (SLS) rocket. The Ground Systems Development and Operations Program is overseeing upgrades and modifications to pad B to support the launch of the SLS and Orion spacecraft for Exploration Mission-1, deep space missions and NASA’s journey to Mars.

The use of AntiMisting Kerosene (AMK) in turbojet engines

NASA Technical Reports Server (NTRS)

Schmidt, H. W.

1981-01-01

The effect of antimisting kerosene (AMK) flow characteristics on fan jet engines and the impact of degradation requirements on the fuel system was evaluated. It was determined from the present program that AMK fuel cannot be used without predegradation, although some degradation occurs throughout the fuel feed system, expecially in the fuel pumps. There is a tendency toward FM-9 AMK additive agglomeration and gel formation when the liquid flows at a critical velocity through very small passages. The data indicate this phenomenon to be a function of the degree of degradation, the passage size, the differential pressure, the fluid temperature, and the accumulated flow time. Additionally, test results indicate that the long term cumulative effects of this phenomenon may require more degradation than the theoretical requirement determined from short term tests.

Application and research of artificial water mist on photoelectric interference

NASA Astrophysics Data System (ADS)

He, Yuejun; Ren, Baolin

2018-04-01

Water mist is a new type of photoelectric interfering material. It can exert a strong interference and shielding effect on infrared light, laser and radar wave through scattering, reflection, refraction and absorption. Based on this, this paper illustrates the application of an artificial high pressure water mist technology in infrared interference system. First, the operating principle of the infrared interference system is introduced. Next, the design principle of self-excited rotary vortex nozzle, the key part of the system, is elaborated. Then, the calculation of the main control parameters of the system is clarified. In the end, the paper verifies interference and shielding effect of the system by experiment. Experiment shows that the interference system can significantly reduce infrared signature of the target, featuring excellent infrared interference performance and high practical value.

Only the chemical state of Indium changes in Mn-doped In3Sb1Te2 (Mn: 10 at.%) during multi-level resistance changes

NASA Astrophysics Data System (ADS)

Lee, Y. M.; Ahn, D.; Kim, J.-Y.; Kim, Y. S.; Cho, S.; Ahn, M.; Cho, M.-H.; Jung, M. S.; Choi, D. K.; Jung, M.-C.; Qi, Y. B.

2014-04-01

We fabricated and characterized the material with Mn (10 at.%: atomic percent) doped In3Sb1Te2 (MIST) using co-sputtering and synchrotron radiation, respectively. The MIST thin film showed phase-changes at 97 and 320°C, with sheet resistances of ~10 kΩsq (amorphous), ~0.2 kΩsq (first phase-change), and ~10 Ωsq (second phase-change). MIST did not exhibit any chemical separation or increased structural instability during either phase-change, as determined with high-resolution x-ray photoelectron spectroscopy. Chemical state changes were only depended for In without concomitant changes of Sb and Te. Apparently, doped Mn atoms can be induced with movement of only In atoms.

Human exposure to polyhexamethylene guanidine phosphate from humidifiers in residential settings: Cause of serious lung disease.

PubMed

Lee, Ji Hyun; Yu, Il Je

2017-11-01

Exposure to the humidifier disinfectant, polyhexamethylene guanidine phosphate (PHMG), in mists generated from ultrasonic humidifiers was studied in a simulation chamber and apartment rooms. PHMG is suspected as a causative agent of lung disease in Korea residences. In the simulation-chamber study, the amount of disinfectant discharged from three different ultrasonic humidifiers was measured. Mists generated at 1, 2, and 4 times the recommended amount of disinfectant were sampled with an impinger, and the effect of relative humidity (RH) on airborne disinfectant concentration was studied by changing RH from 60%-70% to 90%-100%. In addition, particle size distribution (PSD) in mists was measured by scanning mobility particle sizer (SMPS), aerodynamic particle sizer (APS), and Mastersizer. In the apartment study, mists generated from ultrasonic humidifiers were sampled for 6 h in small and large rooms during fall ( n = 10) and winter ( n = 15). In the simulation study, the humidifiers discharged 205 ± 24.6 ml/h of mist at maximum capacity. Concentrations of airborne disinfectant increased with increasing concentration of disinfectant. RH affected airborne disinfectant concentration in the chamber, with increasing concentration with increasing RH. Below RH 70%, no airborne PHMG was detected. PHMG-containing mists generated from ultrasonic humidifier showed various sizes ranging from 149-157 nm to 690-740 nm to larger than 5.4 µm by SMPS, APS, and Mastersizer, respectively. Surface area mean diameter measured by Mastersizer ranged from 5.39 µm to 5.72 µm. In the apartment study conducted during the fall, the geometric mean (GM) and geometric standard deviation (GSD) and arithmetic mean (AM) and standard deviation (SD) of airborne PHMG concentration were 3.22 + 5.13 µg/m 3 and 8.26 ± 12.18 µg/m 3 , respectively. In the winter, GM + GSD and AM ± SD of airborne PHMG concentration were 0.21 + 2.11 µg/m 3 and 0.35 ± 0.62 µg/m 3 , respectively. RH and temperature in the apartment rooms for fall and winter were 22.5 ± 1.7°C, 74.5 ± 15.6% and 22.0 ± 2°C, 51.1 ± 12.9%, respectively. Different RHs in the fall and winter resulted in very different airborne concentrations of disinfectant in the apartment rooms. Exposure levels and PSD of mists generated from ultrasonic humidifiers in apartments are not sufficient to conclude that PHMG causes lung disease in Korean residences.

Fire Suppression Properties of Very Fine Water Mist

DTIC Science & Technology

2005-01-01

with the University of Heidelberg, developed an in situ oxygen sensor based on tunable diode laser absorption spectroscopy ( TDLAS ) to provide absolute... oxygen number densities in the presence of mist.3 Th e TDLAS oxygen sensor provides real-time, calibra- tion-free, quantitative oxygen ...Determination of Molecular Oxygen Concentrations in Full-Scale Fire Suppression Tests Using TDLAS ,” Proc. Combust. Inst. 29, 353-360 (2002).

Recommendations for the use of mist nets for inventory and monitoring of bird populations

Treesearch

C. John Ralph; Erica H. Dunn; Will J. Peach; Colleen M. Handel

2004-01-01

We provide recommendations on the best practices for mist netting for the purposes of monitoring population parameters such as abundance and demography. Studies should be carefully thought out before nets are set up, to ensure that sampling design and estimated sample size will allow study objectives to be met. Station location, number of nets, type of nets, net...

Identification of key transcription factors in caerulein-induced pancreatitis through expression profiling data

PubMed Central

QI, DACHUAN; WU, BO; TONG, DANIAN; PAN, YE; CHEN, WEI

2015-01-01

The current study aimed to isolate key transcription factors (TFs) in caerulein-induced pancreatitis, and to identify the difference between wild type and Mist1 knockout (KO) mice, in order to elucidate the contribution of Mist1 to pancreatitis. The gene profile of GSE3644 was downloaded from the Gene Expression Omnibus database then analyzed using the t-test. The isolated differentially expressed genes (DEGs) were mapped into a transcriptional regulatory network derived from the Integrated Transcription Factor Platform database and in the network, the interaction pairs involving at least one DEG were screened. Fisher’s exact test was used to analyze the functional enrichment of the target genes. A total of 1,555 and 3,057 DEGs were identified in the wild type and Mist1KO mice treated with caerulein, respectively. DEGs screened in Mist1KO mice were predominantly enriched in apoptosis, mitogen-activated protein kinase signaling and other cancer-associated pathways. A total of 188 and 51 TFs associated with pathopoiesis were isolated in Mist1KO and wild type mice, respectively. Out of the top 10 TFs (ranked by P-value), 7 TFs, including S-phase kinase-associated protein 2 (Skp2); minichromosome maintenance complex component 3 (Mcm3); cell division cycle 6 (Cdc6); cyclin B1 (Ccnb1); mutS homolog 6 (Msh6); cyclin A2 (Ccna2); and cyclin B2 (Ccnb2), were expressed in the two types of mouse. These TFs were predominantly involved in phosphorylation, DNA replication, cell division and DNA mismatch repair. In addition, specific TFs, including minichromosome maintenance complex component 7 (Mcm7); lymphoid-specific helicase (Hells); and minichromosome maintenance complex component 6 (Mcm6), that function in the unwinding of DNA were identified to participate in Mist1KO pancreatitis. The DEGs, including Cdc6, Mcm6, Msh6 and Wdr1 are closely associated with the regulation of caerulein-induced pancreatitis. Furthermore, other identified TFs were also involved in this type of regulation. PMID:25975747

Investigations into the formation of nanocrystalline quantum dot thin films by mist deposition process

NASA Astrophysics Data System (ADS)

Kshirsagar, Aditya

Semiconductor nanocrystalline quantum dots (NQDs) have material properties remarkably different compared to bulk semiconductors with the same material composition. These NQDs have various novel applications in the electronic and photonic industry, such as light emitting diodes (LEDs) and flat-panel displays. In these applications, ultra-thin films of NQDs in the monolayer regime are needed to ensure optimal current transport properties and device efficiency. There is ongoing search to find a suitable method to deposit and pattern such ultra-thin films of quantum dots with few monolayer thicknesses. Several competing approaches are available, each with its pros and cons. This study explores mist deposition as the technique to fill this void. In this study, ultra-thin films of quantum dots are deposited on diverse substrates and are characterized to understand the mechanics of mist deposition. Various applications of blanket deposited and patterned quantum dot films are studied. The results discussed here include atomic force microscopy analysis of the films to study surface morphology, fluorescence microscopy to study light emission and optical microscope images to study patterning techniques. These results demonstrate the ability of mist deposition to form 1-4 monolayers thick, uniform, defect-free patterned films with root mean square (RMS) surface roughness less than 2 nm. LEDs fabricated using mist deposition show a peak luminescence greater than 500 cd/m2 for matched red, yellow and green devices using Alq3 as the electron transport layer, and over 9000 cd/m2 for red devices using ZnO as the electron transport layer, respectively. In addition to the experimental approach to study the process and explore potential applications, simulation and modeling are carried out to understand the various aspects of mist deposition. A mathematical model is presented which discusses the atomization process of the precursor solution, the physics involved during the deposition process, and the mechanics of film formation. Results of film morphology simulation using Monte Carlo techniques and process simulation using multi-physics approach are discussed. Problems in pattern transfer due to electrostatic effects when using shadow masks are presented in a separate chapter.

Evaluation of an automatic-timed insecticide application system for backyard mosquito control.

PubMed

Cilek, J E; Hallmon, C F; Johnson, R

2008-12-01

Several manufacturers and pest management companies have begun to market and install outdoor automatically timed insecticide application systems that claim to provide an envelope of protection against host-seeking mosquitoes within a defined area, e.g., residential backyards. A typical system consists of a multi-gallon reservoir attached to a continuous loop of plastic tubing with multiple single spray head nozzles. Nozzles are usually placed along the perimeter of a backyard in landscaping or other areas suitable for mosquito harborage. This array is then connected to a programmable electric pump set to automatically apply an insecticide at predetermined intervals. An operational field study was conducted to evaluate this technology using previously installed MistAway systems at.3 residences in northwestern Florida. This system applied a mist-like application of 0.05% AI synergized pyrethrins for 45 sec at dawn and again at dusk in each backyard. Twice-weekly collections from ABC suction light traps, baited with carbon dioxide, were used as the evaluation tool. Female mosquitoes from treatment backyards were compared with trap collections from 3 backyards without automatic misting systems used as controls. We found that weekly mosquito reduction was highly variable and ranged from 98% to 14% during the 35-wk study. Because the primary method of reduction by these application systems was not well understood, a MistAway system was installed in an outdoor simulated residential backyard to determine exposure pathway under controlled conditions with field cage and excised-leaf bioassays. Using laboratory-reared females of Aedes albopictus and Culex quinquefasciatus in those assays, we found that reduction by the MistAway system was primarily achieved by direct exposure of the mosquitoes to the insecticide application and not from residual deposits on treated vegetation.

The stress-buffering effect of acute exercise: Evidence for HPA axis negative feedback.

PubMed

Zschucke, Elisabeth; Renneberg, Babette; Dimeo, Fernando; Wüstenberg, Torsten; Ströhle, Andreas

2015-01-01

According to the cross-stressor adaptation hypothesis, physically trained individuals show lower physiological and psychological responses to stressors other than exercise, e.g. psychosocial stress. Reduced stress reactivity may constitute a mechanism of action for the beneficial effects of exercise in maintaining mental health. With regard to neural and psychoneuroendocrine stress responses, the acute stress-buffering effects of exercise have not been investigated yet. A sample of highly trained (HT) and sedentary (SED) young men was randomized to either exercise on a treadmill at moderate intensity (60-70% VO2max; AER) for 30 min, or to perform 30 min of "placebo" exercise (PLAC). 90 min later, an fMRI experiment was conducted using an adapted version of the Montreal Imaging Stress Task (MIST). The subjective and psychoneuroendocrine (cortisol and α-amylase) changes induced by the exercise intervention and the MIST were assessed, as well as neural activations during the MIST. Finally, associations between the different stress responses were analysed. Participants of the AER group showed a significantly reduced cortisol response to the MIST, which was inversely related to the previous exercise-induced α-amylase and cortisol fluctuations. With regard to the sustained BOLD signal, we found higher bilateral hippocampus (Hipp) activity and lower prefrontal cortex (PFC) activity in the AER group. Participants with a higher aerobic fitness showed lower cortisol responses to the MIST. As the Hipp and PFC are brain structures prominently involved in the regulation of the hypothalamus-pituitary-adrenal (HPA) axis, these findings indicate that the acute stress-buffering effect of exercise relies on negative feedback mechanisms. Positive affective changes after exercise appear as important moderators largely accounting for the effects related to physical fitness. Copyright © 2014 Elsevier Ltd. All rights reserved.

A comparison of head-out mist bathing, with or without facial fanning, with head-out half-body low-water level bathing in humans--a pilot study.

PubMed

Iwase, Satoshi; Kawahara, Yuko; Nishimura, Naoki; Nishimura, Rumiko; Miwa, Chihiro; Kataoka, Yumiko; Kobayashi, Chihiro; Suzuki, Takahiro; Shigaraki, Masayuki; Maeda, Yoichi; Takada, Hiroki; Watanabe, Yoriko

2014-07-01

To reduce the risks of Japanese-style bathing, half-body bathing (HBLB) has been recommended in Japan, but discomfort due to the cold environment in winter prevents its widespread adoption. The development of the mist sauna, which causes a gradual core temperature rise with sufficient thermal comfort, has reduced the demerits of HBLB. We examined head-out 42 °C mist bathing with 38 °C HBLB up to the navel to see if it could improve thermal comfort without detracting from the merits of HBLB, with and without the effects of facial fanning (FF). The subjects were seven healthy males aged 22-25 years. The following bathing styles were provided: (1) HBLB-head-out half-body low bathing of 38 °C up to the navel (20 min); (2) HOMB-head-out mist bathing of 42 °C and HBLB of 38 °C (20 min); and (3) HOMBFF-HOMB with FF (20 min). HOMB raised the core temperature gradually. HOMBFF suppressed the core temperature rise in a similar fashion to HOMB. Increases in blood pressure and heart rate usually observed in Japanese traditional-style bathing were less marked in HOMBs with no significant difference with and without FF. The greatest body weight loss was observed after Japanese traditional-style bathing, with only one-third of this amount lost after mist bathing, and one-sixth after HBLB. HOMB increased thermal sensation, and FF also enhanced post-bathing invigoration. We conclude that HOMB reduces the risks of Japanese traditional style bathing by mitigating marked changes in the core temperature and hemodynamics, and FF provides thermal comfort and invigoration.

A comparison of head-out mist bathing, with or without facial fanning, with head-out half-body low-water level bathing in humans—a pilot study

NASA Astrophysics Data System (ADS)

Iwase, Satoshi; Kawahara, Yuko; Nishimura, Naoki; Nishimura, Rumiko; Miwa, Chihiro; Kataoka, Yumiko; Kobayashi, Chihiro; Suzuki, Takahiro; Shigaraki, Masayuki; Maeda, Yoichi; Takada, Hiroki; Watanabe, Yoriko

2014-07-01

To reduce the risks of Japanese-style bathing, half-body bathing (HBLB) has been recommended in Japan, but discomfort due to the cold environment in winter prevents its widespread adoption. The development of the mist sauna, which causes a gradual core temperature rise with sufficient thermal comfort, has reduced the demerits of HBLB. We examined head-out 42 °C mist bathing with 38 °C HBLB up to the navel to see if it could improve thermal comfort without detracting from the merits of HBLB, with and without the effects of facial fanning (FF). The subjects were seven healthy males aged 22-25 years. The following bathing styles were provided: (1) HBLB—head-out half-body low bathing of 38 °C up to the navel (20 min); (2) HOMB—head-out mist bathing of 42 °C and HBLB of 38 °C (20 min); and (3) HOMBFF—HOMB with FF (20 min). HOMB raised the core temperature gradually. HOMBFF suppressed the core temperature rise in a similar fashion to HOMB. Increases in blood pressure and heart rate usually observed in Japanese traditional-style bathing were less marked in HOMBs with no significant difference with and without FF. The greatest body weight loss was observed after Japanese traditional-style bathing, with only one-third of this amount lost after mist bathing, and one-sixth after HBLB. HOMB increased thermal sensation, and FF also enhanced post-bathing invigoration. We conclude that HOMB reduces the risks of Japanese traditional style bathing by mitigating marked changes in the core temperature and hemodynamics, and FF provides thermal comfort and invigoration.

Effects of simulated deposition of acid mist and iron ore particulate matter on photosynthesis and the generation of oxidative stress in Schinus terebinthifolius Radii and Sophora tomentosa L.

PubMed

Kuki, Kacilda Naomi; Oliva, Marco Antônio; Pereira, Eduardo Gusmão; Costa, Alan Carlos; Cambraia, José

2008-09-15

Particulate matter is a natural occurrence in the environment, but some industries, such as the iron ore sector, can raise the total amount of particles in the atmosphere. This industry is primarily a source of iron and sulfur dioxide particulates. The effects of the pollutants from the iron ore industries on representatives of restinga vegetation in a Brazilian coastal ecosystem were investigated using physiological and biochemical measures. Two species, Schinus terebinthifolius and Sophora tomentosa, were exposed to simulated deposition of acid mist and iron ore particulate matter in acrylic chambers in a greenhouse. Parameters such as gas exchange, fluorescence emission, chlorophyll content, total iron content, antioxidant enzyme activity and malondialdehyde content were assessed in order to evaluate the responses of the two species. Neither treatment was capable of inducing oxidative stress in S. terebinthifolius. Nevertheless, the deposition of iron ore particulates on this species increased chlorophyll content, the maximum quantum efficiency of photosystem II and the electron transport rate, while iron content was unaltered. On the other hand, S. tomentosa showed a greater sensitivity to the treatments. Plants of S. tomentosa that were exposed to acid mist had a decrease in photosynthesis, while the deposition of iron particulate matter led to an increase in iron content and membrane permeability of the leaves. The activities of antioxidant enzymes, such as catalases and superoxide dismutase, were enhanced by both treatments. The results suggested that the two restinga species use different strategies to overcome the stressful conditions created by the deposition of particulate matter, either solid or wet. It seems that while S. terebinthifolius avoided stress, S. tomentosa used antioxidant enzyme systems to partially neutralize oxidative stress. The findings also point to the potential use of S. tomentosa as a biomarker species under field conditions.

A comparison of point-count and mist-net detections of songbirds by habitat and time-of-season

Treesearch

Rich W. Pagen; Frank R., III Thompson; Dirk E. Burhans

2002-01-01

We compared the results of point-count and mist-net surveys during the breeding and post-breeding seasons in four Missouri Ozark habitats: mature upland forest, mature riparian forest, 9- to 10-yr-old upland forest and 3- to 4-yr-old upland forest created by clearcutting. We determined whether differences in abundance estimates among habitats or between breeding and...

Microgravity

NASA Image and Video Library

2002-07-02

Members of the Water Mist experiment team float in the NASA KC-135 low-g aircraft during preflight tests of the experiment. At center is J. Thomas McKirnon (principal investigator); at right is Angel Abbud-Madrid (co-PI and project scientist). They are with the Center for Commercial Applications of Combustion in Space at the Colorado School of Mines. Water Mist will investigate how best to extinguish flames by using ultrafine droplets of water.

Effects of calcium fertilization and acid mist on calcium concentration and cold tolerance of red spruce needles

Treesearch

G. R. Strimbeck; David R. Vann; Arthur H. Johnson

1996-01-01

Several studies have shown that exposure to acid mist impairs cold tolerance of red spruce foliage, predisposing it to winter injury, which appears to be a major factor in the decline of montane populations of the species. Other studies have shown increases in calcium (Ca) concentration in canopy throughfall in montane spruce-fir forests, and decreases in foliar Ca...

Development and characterization of nanostructured mists with potential for actively targeting poorly water-soluble compounds into the lungs.

PubMed

Nesamony, Jerry; Kalra, Ashish; Majrad, Mohamed S; Boddu, Sai Hanuman Sagar; Jung, Rose; Williams, Frederick E; Schnapp, Alaina M; Nauli, Surya M; Kalinoski, Andrea L

2013-10-01

To formulate nanoemulsions (NE) with potential for delivering poorly water-soluble drugs to the lungs. A self nanoemulsifying composition consisting of cremophor RH 40, PEG 400 and labrafil M 2125 CS was selected after screening potential excipients. The solubility of carbamazepine, a poorly water-soluble drug, was tested in the formulation components. Oil-in-water (o/w) NEs were characterized using dynamic light scattering, electrophoretic light scattering, transmission electron microscopy (TEM) and differential scanning calorimetry. NEs were nebulized into a mist using a commercial nebulizer and characterized using laser diffraction and TEM. An aseptic method was developed for preparing sterile NEs. Biocompatibility of the formulation was evaluated on NIH3T3 cells using MTT assay. In vitro permeability of the formulation was tested in zebra fish eggs, HeLa cells, and porcine lung tissue. NEs had neutrally charged droplets of less than 20 nm size. Nebulized NEs demonstrated an o/w nanostructure. The mist droplets were of size less than 5 μm. Sterility testing and cytotoxicity results validated that the NE was biocompatible and sterile. In vitro tests indicated oil nanodroplets penetrating intracellularly through biological membranes. The nanoemulsion mist has the potential for use as a pulmonary delivery system for poorly water-soluble drugs.

Numerical investigation of mist/air impingement cooling on ribbed blade leading-edge surface.

PubMed

Bian, Qingfei; Wang, Jin; Chen, Yi-Tung; Wang, Qiuwang; Zeng, Min

2017-12-01

The working gas turbine blades are exposed to the environment of high temperature, especially in the leading-edge region. The mist/air two-phase impingement cooling has been adopted to enhance the heat transfer on blade surfaces and investigate the leading-edge cooling effectiveness. An Euler-Lagrange particle tracking method is used to simulate the two-phase impingement cooling on the blade leading-edge. The mesh dependency test has been carried out and the numerical method is validated based on the available experimental data of mist/air cooling with jet impingement on a concave surface. The cooling effectiveness on three target surfaces is investigated, including the smooth and the ribbed surface with convex/concave columnar ribs. The results show that the cooling effectiveness of the mist/air two-phase flow is better than that of the single-phase flow. When the ribbed surfaces are used, the heat transfer enhancement is significant, the surface cooling effectiveness becomes higher and the convex ribbed surface presents a better performance. With the enhancement of the surface heat transfer, the pressure drop in the impingement zone increases, but the incremental factor of the flow friction is smaller than that of the heat transfer enhancement. Copyright © 2017 Elsevier Ltd. All rights reserved.

Correlation between perceptual, visuo-spatial, and psychomotor aptitude to duration of training required to reach performance goals on the MIST-VR surgical simulator.

PubMed

McClusky, D A; Ritter, E M; Lederman, A B; Gallagher, A G; Smith, C D

2005-01-01

Given the dynamic nature of modern surgical education, determining factors that may improve the efficiency of laparoscopic training is warranted. The objective of this study was to analyze whether perceptual, visuo-spatial, or psychomotor aptitude are related to the amount of training required to reach specific performance-based goals on a virtual reality surgical simulator. Sixteen MS4 medical students participated in an elective skills course intended to train laparoscopic skills. All were tested for perceptual, visuo-spatial, and psychomotor aptitude using previously validated psychological tests. Training involved as many instructor-guided 1-hour sessions as needed to reach performance goals on a custom designed MIST-VR manipulation-diathermy task (Mentice AB, Gothenberg, Sweden). Thirteen subjects reached performance goals by the end of the course. Two were excluded from analysis due to previous experience with the MIST-VR (total n = 11). Perceptual ability (r = -0.76, P = 0.007) and psychomotor skills (r = 0.62, P = 0.04) significantly correlated with the number of trials required. Visuo-spatial ability did not significantly correlate with training duration. The number of trials required to train subjects to performance goals on the MIST-VR manipulation diathermy task is significantly related to perceptual and psychomotor aptitude.

Measurement Instrument for Scientific Teaching (MIST): A Tool to Measure the Frequencies of Research-Based Teaching Practices in Undergraduate Science Courses

PubMed Central

Durham, Mary F.; Knight, Jennifer K.; Couch, Brian A.

2017-01-01

The Scientific Teaching (ST) pedagogical framework provides various approaches for science instructors to teach in a way that more closely emulates how science is practiced by actively and inclusively engaging students in their own learning and by making instructional decisions based on student performance data. Fully understanding the impact of ST requires having mechanisms to quantify its implementation. While many useful instruments exist to document teaching practices, these instruments only partially align with the range of practices specified by ST, as described in a recently published taxonomy. Here, we describe the development, validation, and implementation of the Measurement Instrument for Scientific Teaching (MIST), a survey derived from the ST taxonomy and designed to gauge the frequencies of ST practices in undergraduate science courses. MIST showed acceptable validity and reliability based on results from 7767 students in 87 courses at nine institutions. We used factor analyses to identify eight subcategories of ST practices and used these categories to develop a short version of the instrument amenable to joint administration with other research instruments. We further discuss how MIST can be used by instructors, departments, researchers, and professional development programs to quantify and track changes in ST practices. PMID:29196428

An Apollo compatible cloud physics experiment.

NASA Technical Reports Server (NTRS)

Eaton, L. R.; Hollinden, A. B.; Satterblom, P. R.

1973-01-01

Consideration of the utilization of a low-gravity environment to obtain experimental information, in the area of cloud microphysics, which cannot be obtained in ground laboratories. The experiment discussed is designed to obtain quantitative answers about evaporation and breakup of salt particles from ocean spray and other sources. In addition to salt nuclei distribution mechanisms, this breakup has ecological importance in relation to the spreading of salt mists from salted highways and spreading of brine cooling tower spray from electrical power generation plants. This experiment is being submitted for consideration on the Apollo-Soyuz Test Program in 1975.

A technique to prevent capturing birds in unattended, furled mist nets

USGS Publications Warehouse

Sykes, P.W.

1989-01-01

A technique was developed to prevent the inadvertent capturing of birds in unattended mist nets left in place for long periods of time. This was accomplished by placing furled nets on top of 9-inch wide strips of 30-pound roofing felt secured to the ground between net support poles. All materials used are widely available and procedures used to make the felt strips and install them are described.

Separation of metal ions in nitrate solution by ultrasonic atomization

NASA Astrophysics Data System (ADS)

Sato, Masanori; Ikeno, Masayuki; Fujii, Toshitaka

2004-11-01

In the ultrasonic atomization of metal nitrate solutions, the molar ratio of metal ions is changed between solution and mist. Small molar metal ions tend to be transferred to mist by ultrasonic wave acceleration, while large molar ions tend to remain in solution. As a result, metal ions can be separated by ultrasonic atomization. We show experimental data and propose a conceptual mechanism for the ultrasonic separation of metal ions.

Catheter and Laryngeal Mask Endotracheal Surfactant Therapy: the CALMEST approach as a novel MIST technique.

PubMed

Vannozzi, Ilaria; Ciantelli, Massimiliano; Moscuzza, Francesca; Scaramuzzo, Rosa T; Panizza, Davide; Sigali, Emilio; Boldrini, Antonio; Cuttano, Armando

2017-10-01

Neonatal respiratory distress syndrome (RDS) is a major cause of mortality and morbidity among preterm infants. Although the INSURE (INtubation, SURfactant administration, Estubation) technique for surfactant replacement therapy is so far the gold standard method, over the last years new approaches have been studied, i.e. less invasive surfactant administration (LISA) or minimally invasive surfactant therapy (MIST). Here we propose an originally modified MIST, called CALMEST (Catheter And Laryngeal Mask Endotracheal Surfactant Therapy), using a particular laryngeal mask as a guide for a thin catheter to deliver surfactant directly in the trachea. We performed a preliminary study on a mannequin and a subsequent in vivo pilot trial. This novel procedure is quick, effective and well tolerated and might represent an improvement in reducing neonatal stress. Ultimately, CALMEST offers an alternative approach that could be extremely useful for medical staff with low expertise in laryngoscopy and intubation.

Zero Gravity Aircraft Testing of a Prototype Portable Fire Extinguisher for Use in Spacecraft

NASA Astrophysics Data System (ADS)

Butz, J.; Carriere, T.; Abbud-Madrid, A.; Easton, J.

2012-01-01

For the past five years ADA Technologies has been developing a portable fire extinguisher (PFE) for use in microgravity environments. This technology uses fine water mist (FWM) to effectively and efficiently extinguish fires representative of spacecraft hazards. Recently the FWM PFE was flown on a Zero-G (reduced gravity) aircraft to validate the performance of the technology in a microgravity environment. Test results demonstrated that droplet size distributions generated in the reduced gravity environment were in the same size range as data collected during normal gravity (1-g) discharges from the prototype PFE. Data taken in an obscured test configuration showed that the mist behind the obstacle was more dense in the low-g environment when compared to 1-g discharges. The mist behind the obstacle tended to smaller droplet sizes in both the low-g and 1-g test conditions.

Studies of mist deposition for the formation of quantum dot CdSe films

NASA Astrophysics Data System (ADS)

Price, S. C.; Shanmugasundaram, K.; Ramani, S.; Zhu, T.; Zhang, F.; Xu, J.; Mohney, S. E.; Zhang, Q.; Kshirsagar, A.; Ruzyllo, J.

2009-10-01

Films of CdSe(ZnS) colloidal nanocrystalline quantum dots (NQDs) were deposited on bare silicon, glass and polymer coated silicon using mist deposition. This effort is a part of an exploratory investigation in which this deposition technique is studied for the first time as a method to form semiconductor NQD films. The process parameters, including deposition time, solution concentration and electric field, were varied to change the thickness of the deposited film. Blanket films and films deposited through a shadow mask were created to investigate the method's ability to pattern films during the deposition process. The differences between these deposition modes in terms of film morphology were observed. Overall, the results show that mist deposition of quantum dots is a viable method for creating thin, patterned quantum dot films using colloidal solution as the precursor. It is concluded that this technique shows very good promise for quantum dot (light emitting diode, LED) fabrication.

Study on the effectiveness of Extreme Cold Mist MQL system on turning process of stainless steel AISI 316

NASA Astrophysics Data System (ADS)

Jamaludin, A. S.; Hosokawa, A.; Furumoto, T.; Koyano, T.; Hashimoto, Y.

2018-03-01

Cutting process of difficult-to-cut material such as stainless steel, generates immensely excessive heat, which is one of the major causes related to shortening tool life and lower quality of surface finish. It is proven that application of cutting fluid during the cutting process of difficult-to-cut material is able to improve the cutting performance, but excessive application of cutting fluid leads to another problem such as increasing processing cost and environmental hazardous pollution of workplace. In the study, Extreme Cold Mist system is designed and tested along with various Minimum Quantity Lubrication (MQL) systems on turning process of stainless steel AISI 316. In the study, it is obtained that, Extreme Cold Mist system is able to reduce cutting force up to 60N and improve the surface roughness of the machined surface significantly.

Moisture Separator Reheater for NPP Turbines

NASA Astrophysics Data System (ADS)

Manabe, Jun; Kasahara, Jiro

This paper introduces the development of the current model Moisture Separator Reheater (MSR) for nuclear power plant (NPP) turbines, commercially placed in service in the period 1984-1997, focusing on the mist separation performance of the MSR along with drainage from heat exchanger tubes. A method of predicting the mist separation performance was devised first based on the observation of mist separation behaviors under an air-water test. Then the method was developed for the application to predict under the steam conditions, followed by the verification in comparison with the actual results of a steam condition test. The instability of tube drainage associated with both sub-cooling and temperature oscillation might adversely affect the seal welding of tubes to tube sheet due to thermal fatigue. The instability was measured on an existing unit to clarify behaviors and the development of a method to suppress them. Both methods were applied to newly constructed units and the effectiveness of the methods was demonstrated.

DENSITY: software for analysing capture-recapture data from passive detector arrays

USGS Publications Warehouse

Efford, M.G.; Dawson, D.K.; Robbins, C.S.

2004-01-01

A general computer-intensive method is described for fitting spatial detection functions to capture-recapture data from arrays of passive detectors such as live traps and mist nets. The method is used to estimate the population density of 10 species of breeding birds sampled by mist-netting in deciduous forest at Patuxent Research Refuge, Laurel, Maryland, U.S.A., from 1961 to 1972. Total density (9.9 ? 0.6 ha-1 mean ? SE) appeared to decline over time (slope -0.41 ? 0.15 ha-1y-1). The mean precision of annual estimates for all 10 species pooled was acceptable (CV(D) = 14%). Spatial analysis of closed-population capture-recapture data highlighted deficiencies in non-spatial methodologies. For example, effective trapping area cannot be assumed constant when detection probability is variable. Simulation may be used to evaluate alternative designs for mist net arrays where density estimation is a study goal.

KSC-2014-4326

NASA Image and Video Library

2014-07-24

CAPE CANAVERAL, Fla. – Inside the Prototype Laboratory at NASA's Kennedy Space Center in Florida, Evan Williams, left, an Education intern from the University of Central Florida, and Anthony Bharrat, NASA avionics lead, prepare the experiment container for NASA's Exposing Microorganisms in the Stratosphere, or E-MIST, experiment. In the background is David J. Smith, Ph.D., NASA E-MIST principal investigator. The container was designed and built at Kennedy. The 80-pound structure features four doors that rotate to expose up to 10 microbial samples each for a predetermined period of time in the Earth's stratosphere. The E-MIST experiment will launch on the exterior of a giant scientific balloon gondola at about 8 a.m. MST on Aug. 24 from Ft. Sumner, New Mexico. It will soar 125,000 feet above the Earth during a 5-hour journey over the desert to understand how spore-forming bacteria, commonly found in spacecraft assembly facilities can survive. Photo credit: NASA/Kim Shiflett

MIST - MINIMUM-STATE METHOD FOR RATIONAL APPROXIMATION OF UNSTEADY AERODYNAMIC FORCE COEFFICIENT MATRICES

NASA Technical Reports Server (NTRS)

Karpel, M.

1994-01-01

Various control analysis, design, and simulation techniques of aeroservoelastic systems require the equations of motion to be cast in a linear, time-invariant state-space form. In order to account for unsteady aerodynamics, rational function approximations must be obtained to represent them in the first order equations of the state-space formulation. A computer program, MIST, has been developed which determines minimum-state approximations of the coefficient matrices of the unsteady aerodynamic forces. The Minimum-State Method facilitates the design of lower-order control systems, analysis of control system performance, and near real-time simulation of aeroservoelastic phenomena such as the outboard-wing acceleration response to gust velocity. Engineers using this program will be able to calculate minimum-state rational approximations of the generalized unsteady aerodynamic forces. Using the Minimum-State formulation of the state-space equations, they will be able to obtain state-space models with good open-loop characteristics while reducing the number of aerodynamic equations by an order of magnitude more than traditional approaches. These low-order state-space mathematical models are good for design and simulation of aeroservoelastic systems. The computer program, MIST, accepts tabular values of the generalized aerodynamic forces over a set of reduced frequencies. It then determines approximations to these tabular data in the LaPlace domain using rational functions. MIST provides the capability to select the denominator coefficients in the rational approximations, to selectably constrain the approximations without increasing the problem size, and to determine and emphasize critical frequency ranges in determining the approximations. MIST has been written to allow two types data weighting options. The first weighting is a traditional normalization of the aerodynamic data to the maximum unit value of each aerodynamic coefficient. The second allows weighting the importance of different tabular values in determining the approximations based upon physical characteristics of the system. Specifically, the physical weighting capability is such that each tabulated aerodynamic coefficient, at each reduced frequency value, is weighted according to the effect of an incremental error of this coefficient on aeroelastic characteristics of the system. In both cases, the resulting approximations yield a relatively low number of aerodynamic lag states in the subsequent state-space model. MIST is written in ANSI FORTRAN 77 for DEC VAX series computers running VMS. It requires approximately 1Mb of RAM for execution. The standard distribution medium for this package is a 9-track 1600 BPI magnetic tape in DEC VAX FILES-11 format. It is also available on a TK50 tape cartridge in DEC VAX BACKUP format. MIST was developed in 1991. DEC VAX and VMS are trademarks of Digital Equipment Corporation. FORTRAN 77 is a registered trademark of Lahey Computer Systems, Inc.

Size and Velocity Characteristics of Droplets Generated by Thin Steel Slab Continuous Casting Secondary Cooling Air-Mist Nozzles

NASA Astrophysics Data System (ADS)

Minchaca M, J. I.; Castillejos E, A. H.; Acosta G, F. A.

2011-06-01

Direct spray impingement of high temperature surfaces, 1473 K to 973 K (1200 °C to 700 °C), plays a critical role in the secondary cooling of continuously cast thin steel slabs. It is known that the spray parameters affecting the local heat flux are the water impact flux w as well as the droplet velocity and size. However, few works have been done to characterize the last two parameters in the case of dense mists ( i.e., mists with w in the range of 2 to 90 L/m2s). This makes it difficult to rationalize how the nozzle type and its operating conditions must be selected to control the cooling process. In the present study, particle/droplet image analysis was used to determine the droplet size and velocity distributions simultaneously at various locations along the major axis of the mist cross section at a distance where the steel strand would stand. The measurements were carried out at room temperature for two standard commercial air-assisted nozzles of fan-discharge type operating over a broad range of conditions of practical interest. To achieve statistically meaningful samples, at least 6000 drops were analyzed at each location. Measuring the droplet size revealed that the number and volume frequency distributions were fitted satisfactorily by the respective log-normal and Nukiyama-Tanasawa distributions. The correlation of the parameters of the distribution functions with the water- and air-nozzle pressures allowed for reasonable estimation of the mean values of the size of the droplets generated. The ensemble of measurements across the mist axis showed that the relationship between the droplet velocity and the diameter exhibited a weak positive correlation. Additionally, increasing the water flow rate at constant air pressure caused a decrease in the proportion of the water volume made of finer droplets, whereas the volume proportion of faster droplets augmented until the water flow reached a certain value, after which it decreased. Diminishing the air-to-water flow rates ratio, particularly below 10, resulted in mists of bigger and slower droplets with low impinging Weber numbers. However, increasing the air pressure maintaining a constant water flow rate caused a greater proportion of finer and faster drops with Weber numbers greater than 80, which suggests an increased probability of wet drop contact with a hot surface that would intensify heat extraction.

Two-phase flow characteristics of liquid nitrogen in vertically upward 0.5 and 1.0 mm micro-tubes: Visualization studies

NASA Astrophysics Data System (ADS)

Zhang, P.; Fu, X.

2009-10-01

Application of liquid nitrogen to cooling is widely employed in many fields, such as cooling of the high temperature superconducting devices, cryosurgery and so on, in which liquid nitrogen is generally forced to flow inside very small passages to maintain good thermal performance and stability. In order to have a full understanding of the flow and heat transfer characteristics of liquid nitrogen in micro-tube, high-speed digital photography was employed to acquire the typical two-phase flow patterns of liquid nitrogen in vertically upward micro-tubes of 0.531 and 1.042 mm inner diameters. It was found from the experimental results that the flow patterns were mainly bubbly flow, slug flow, churn flow and annular flow. And the confined bubble flow, mist flow, bubble condensation and flow oscillation were also observed. These flow patterns were characterized in different types of flow regime maps. The surface tension force and the size of the diameter were revealed to be the major factors affecting the flow pattern transitions. It was found that the transition boundaries of the slug/churn flow and churn/annular flow of the present experiment shifted to lower superficial vapor velocity; while the transition boundary of the bubbly/slug flow shifted to higher superficial vapor velocity compared to the results of the room-temperature fluids in the tubes with the similar hydraulic diameters. The corresponding transition boundaries moved to lower superficial velocity when reducing the inner diameter of the micro-tubes. Time-averaged void fraction and heat transfer characteristics for individual flow patterns were presented and special attention was paid to the effect of the diameter on the variation of void fraction.

SPACESUIT DONNING AND DOFFING - ZERO-G TRAINING - DON PETERSON - STS-6

NASA Image and Video Library

1982-07-14

Spacesuit Donning and Doffing in Zero-G Training for Don Peterson of the STS-6 Crew with Astronaut Jerry Ross assisting; and, apparatus for testing the JSC Mechanically-Induced Settling Technology (MIST) Experiment. The training is being held aboard the KC-135 to simulate weightlessness. He is being assisted to don the lower torso of the Extravehicular Mobility Unit (EMU) by an ILC Technician. 1. ASTRONAUT ROSS, JERRY L. - ZERO-G SUITING 2. SHUTTLE - EXPERIMENTS (MIST)

29 CFR 1915.1000 - Air contaminants.

Code of Federal Regulations, 2012 CFR

2012-07-01

... E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist, mineral 8012-95-1 — 5... — Turpentine 8006-64-2 100 560 — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist...

29 CFR 1915.1000 - Air contaminants.

Code of Federal Regulations, 2014 CFR

2014-07-01

... E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist, mineral 8012-95-1 — 5... — Turpentine 8006-64-2 100 560 — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist...

29 CFR 1915.1000 - Air contaminants.

Code of Federal Regulations, 2013 CFR

2013-07-01

... E Octachloronaphthalene 2234-13-1 — 0.1 X Octane 111-65-9 400 1900 — Oil mist, mineral 8012-95-1 — 5... — Turpentine 8006-64-2 100 560 — Uranium (as U) 7440-61-1 Soluble compounds — 0.2 — Insoluble compounds — 0.2 — Vanadium 1314-62-1 Respirable dust (as V2 O5) — (C)0.5 — Fume (as V2 O5) — (C)0.1 — Vegetable oil mist...

Posttest analysis of MIST Test 330302 using TRAC-PF1/MOD1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyack, B E

This report discusses a posttest analysis of Multi-Loop Integral System Test (MIST) 330302 which has been performed using TRAC-PF1/MOD1. This test was one of group performed in the MIST facility to investigate high-pressure injection (HPI)-power-operated relief valve (PORV) cooling, also known as feed-and-bleed cooling. In Test 330302, HPI cooling was delayed 20 min after opening and locking the PORV open to induce extensive system voiding. We have concluded that the TRAC-calculated results are in reasonable overall agreement with the data for Test 330302. All major trends and phenomena were correctly predicted. Differences observed between the measured and calculated results havemore » been traced and related, in part, to deficiencies in our knowledge of the facility configuration and operation. We have identified two models forwhich additional review is appropriate. However, in general, the TRAC closure models and correlations appear to be adequate for the prediction of the phenomena expected to occur during feed-and-bleed transientsin the MIST facility. We believe that the correct conclusions about trends and phenomena will be reached if the code is used in similar applications. Conclusions reached regarding use of the code to calculate similar phenomena in full-size plants (scaling implications) and regulatory implications of this work are also presented.« less

Discriminative validity of the Minimally Invasive Surgical Trainer in Virtual Reality (MIST-VR) using criteria levels based on expert performance.

PubMed

Gallagher, A G; Lederman, A B; McGlade, K; Satava, R M; Smith, C D

2004-04-01

Increasing constraints on the time and resources needed to train surgeons have led to a new emphasis on finding innovative ways to teach surgical skills outside the operating room. Virtual reality training has been proposed as a method to both instruct surgical students and evaluate the psychomotor components of minimally invasive surgery ex vivo. The performance of 100 laparoscopic novices was compared to that of 12 experienced (>50 minimally invasive procedures) and 12 inexperienced (<10 minimally invasive procedures) laparoscopic surgeons. The values of the experienced surgeons' performance were used as benchmark comparators (or criterion measures). Each subject completed six tasks on the Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) three times. The outcome measures were time to complete the task, number of errors, economy of instrument movement, and economy of diathermy. After three trials, the mean performance of the medical students approached that of the experienced surgeons. However, 7-27% of the scores of the students fell more than two SD below the mean scores of the experienced surgeons (the criterion level). The MIST-VR system is capable of evaluating the psychomotor skills necessary in laparoscopic surgery and discriminating between experts and novices. Furthermore, although some novices improved their skills quickly, a subset had difficulty acquiring the psychomotor skills. The MIST-VR may be useful in identifying that subset of novices.

Effect of NaCl Solution Spraying on Fatigue Lives of Smooth and Slit Specimens of 0.37% Carbon Steel

NASA Astrophysics Data System (ADS)

Makabe, Chobin; Ferdous, Md. Shafiul; Shimabukuro, Akimichi; Murdani, Anggit

2017-07-01

The fatigue crack initiation life and growth rate are affected by experimental conditions. A corrosive environment can be created in a laboratory by means of dropping salt water onto the specimen surface, spraying chloride mist into the experimental chamber, etc. In the case of smooth specimens of some metals, fatigue life is shortened and the fatigue limit disappears under such corrosive experimental conditions. In this study, the effects of intermittent spraying of 3% NaCl solution-mist on corrosion fatigue behavior were investigated. The material used was 0.37% carbon steel. This is called JIS S35C in Japan. Spraying of 3% NaCl solution-mist attacked the surface layer of the specimen. It is well known that the pitting, oxidation-reduction reaction, etc. affect the fatigue strength of metals in a corrosive environment. We carried out corrosion fatigue tests with smooth specimens, holed specimens and slit specimens. Then the effects of such specimen geometry on the fatigue strength were investigated when the NaCl solution-mist was sprayed onto the specimen surface. In the case of lower stress amplitude application in slit specimens, the fatigue life in a corrosive atmosphere was longer than that in the open air. It is discussed that the behavior is related to the crack closure which happens when the oxide builds up and clogs the crack or slit.

Size distributions and exposure concentrations of nanoparticles associated with the emissions of oil mists from fastener manufacturing processes.

PubMed

Wang, Ying-Fang; Tsai, Perng-Jy; Chen, Chun-Wan; Chen, Da-Ren; Dai, Yu-Tung

2011-12-30

The aims of the present study were set out to measure size distributions and estimate workers' exposure concentrations of oil mist nanoparticles in three selected workplaces of the forming, threading, and heat treating areas in a fastener manufacturing plant by using a modified electrical aerosol detector (MEAD). The results were further compared with those simultaneously obtained from a nanoparticle surface area monitor (NSAM) and a scanning mobility particle sizer (SMPS) for the validation purpose. Results show that oil mist nanoparticles in the three selected process areas were formed mainly through the evaporation and condensation processes. The measured size distributions of nanoparticles were consistently in the form of uni-modal. The estimated fraction of nanoparticles deposited on the alveolar (AV) region was consistently much higher than that on the head airway (HD) and tracheobronchial (TB) regions in both number and surface area concentration bases. However, a significant difference was found in the estimated fraction of nanoparticles deposited on each individual region while different exposure metrics were used. Comparable results were found between results obtained from both NSAM and MEAD. After normalization, no significant difference can be found between the results obtained from SMPS and MEAD. It is concluded that the obtained MEAD results are suitable for assessing oil mist nanoparticle exposures. Copyright © 2011 Elsevier B.V. All rights reserved.

Assessment of individual hand performance in box trainers compared to virtual reality trainers.

PubMed

Madan, Atul K; Frantzides, Constantine T; Shervin, Nina; Tebbit, Christopher L

2003-12-01

Training residents in laparoscopic skills is ideally initiated in an inanimate laboratory with both box trainers and virtual reality trainers. Virtual reality trainers have the ability to score individual hand performance although they are expensive. Here we compared the ability to assess dominant and nondominant hand performance in box trainers with virtual reality trainers. Medical students without laparoscopic experience were utilized in this study (n = 16). Each student performed tasks on the LTS 2000, an inanimate box trainer (placing pegs with both hands and transferring pegs from one hand to another), as well as a task on the MIST-VR, a virtual reality trainer (grasping a virtual object and placing it in a virtual receptable with alternating hands). A surgeon scored students for the inanimate box trainer exercises (time and errors) while the MIST-VR scored students (time, economy of movements, and errors for each hand). Statistical analysis included Pearson correlations. Errors and time for the one-handed tasks on the box trainer did not correlate with errors, time, or economy measured for each hand by the MIST-VR (r = 0.01 to 0.30; P = NS). Total errors on the virtual reality trainer did correlate with errors on transferring pege (r = 0.61; P < 0.05). Economy and time of both dominant and nondominant hand from the MIST-VR correlated with time of transferring pegs in the box trainer (r = 0.53 to 0.77; P < 0.05). While individual hand assessment by the box trainer during 2-handed tasks was related to assessment by the virtual reality trainer, individual hand assessment during 1-handed tasks did not correlate with the virtual reality trainer. Virtual reality trainers, such as the MIST-VR, allow assessment of individual hand skills which may lead to improved laparoscopic skill acquisition. It is difficult to assess individual hand performance with box trainers alone.

Comparison of methods for the measurement of mist and vapor from light mineral oil-based metalworking fluids.

PubMed

Simpson, Andrew T

2003-11-01

The measurement of oil mist derived from metalworking fluids formulated with light mineral oils can be highly inaccurate when using traditional filter sampling. This is due to evaporation of oil from the filter. In this work the practicability of an alternative approach measuring total oil mist and vapor was investigated. Combinations of inhalable particle samplers with backup sorbent vapor traps and standard vapor sampling on pumped and diffusive sorbent tubes were evaluated with gravimetric, infrared spectroscopic, and gas chromatographic analytical methods against the performance requirements of European Standard EN 482. An artificial aerosol was used to compare the methods against a reference method of filter sampler in series with three impingers. Multi-orifice samplers were used with standard 8-mm diameter charcoal tubes at 2 L/min without any signs of channelling or significant breakthrough, as were conical inhalable samplers with XAD-2 tubes at 1 L/min. Most combinations of samplers had a bias of less than 3 percent, but solitary pumped charcoal tubes underestimated total oil by 13 percent. Diffusive sampling was affected by impaction of mist particles and condensation of oil vapor. Gravimetric analysis of filters revealed significant potential sample loss during storage, with 4 percent being lost after one day when stored at room temperature and 2 percent when refrigerated. Samples left overnight in the balance room to equilibrate lost 24 percent. Infrared spectroscopy gave more precise results for vapor than gas chromatography (p = 0.002). Gas chromatography was less susceptible to bias from contaminating solvent vapors than infrared spectroscopy, but was still vulnerable to petroleum distillates. Under the specific test conditions (one oil type and mist particle size), all combinations of methods examined complied with the requirements of European Standard EN 484. Total airborne oil can be measured accurately; however, care must be taken to avoid contamination by hydrocarbon solvent vapors during sampling.

Improving gas dehydrator efficiency; Glycol losses from dehydrator solved by mist eliminator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franke, S.; Neal, R.; Patel, K.

1989-07-01

Triethylene glycol losses from a natural gas dehydrator unit were costing Winnie Pipeline Co. well over $100/day. Several possible causes had been investigated, and a second, smaller unit had been added because insufficient capacity was thought to cause glycol carryover from the contactor. Eventually, glycol losses were virtually eliminated by replacing the standard mist eliminator pad in the top of the contactor tower with a higher-efficiency type. Use of this type of pad is discussed in this paper.

Bioenergetics of Stromal Cells As a Predictor of Aggressive Prostate Cancer

DTIC Science & Technology

2015-09-01

presence of glucose or glutamine alone or in combination compared to RWPE-1 cells and decreases with increasing malignancy. Glutamine maintained higher...increasing malignancy in presence of glucose or glutamine alone or in combination. It was performed using MIST. MiST: After three baseline OCR...measurements in an assay medium (DMEM containing 10 mM glucose, 4 mM glutamine at pH 7.4 without bicarbonate), Oligomycin (1.0 μM), FCCP (0.125 μM), and

Fire Protection of Weapon Storage and Water Mist Redundancy Philosophies

DTIC Science & Technology

2012-11-01

criteria me system ged system ozzles dummy tor d, insulated titute of Swe stems pedo pipe Date 2012 den Refere -03-31 P90 nce 0038-04...test wit tion test wit ution test wi t system, 10 st system, 5 m, 5 bar, 50 , 10 bar, 50 ummy, free- edo dummy pedo dummy pedo dummy ummy, dren...systems usi lower volum pedo dumm temperature discharge d ion. h Institute ynamics dström Date 2012 den ater mist/wa ests indicate fire

High T(sub c) superconductors fabricated by plasma aerosol mist deposition technique

NASA Technical Reports Server (NTRS)

Wang, X. W.; Vuong, K. D.; Leone, A.; Shen, C. Q.; Williams, J.; Coy, M.

1995-01-01

We report new results on high T(sub c) superconductors fabricated by a plasma aerosol mist deposition technique, in atmospheric environment. Materials fabricated are YBaCuO, BiPbSrCaCuO, BaCaCuO precursor films for TlBaCaCuO, and other buffers such as YSZ. Depending on processing conditions, sizes of crystallites and/or particles are between dozens of nano-meters and several micrometers. Superconductive properties and other material characteristics can also be tailored.

The Schladitz Fuel Injector: An Initial Performance Evaluation without Burning.

DTIC Science & Technology

1982-03-01

same heating rate in the absence of the exit nozzle. Stated alternatively , the presence of the downstream nozzle reduced the required heat addition...rate by about one-third for formation of a spray having 50% or more mist content. It was further noted that this heating rate reduction was essentially...plot for Jet-A fuel suggests that the creation of a fine mist by the SFI in the absence of any downstream nozzle is accompanied by the formation of a

Fractography of glass at the nanometer scale

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guilloteau, E.; Arribart, H.; Creuzet, F.

1996-12-01

The authors present a nanometer scale description of the fracture surface of soda-lime glass. This is achieved by the use of Atomic Force Microscopy. The mirror zone is shown to be built with elementary entities, the density of which increases continuously while the mist and hackle zones are approached. Moreover, the overall picture leads to some kind of self-similarity, in the sense that small regions of the hackle zone exhibit the full set of mirror, mist and hackle areas.

Effect of acid mist and air pollutants on yellow-poplar seedling height and leaf growth

Treesearch

Leon S. Dochinger; Keith F. Jensen; Keith F. Jensen

1985-01-01

One-year-old yellow-poplar seedlings were treated with acid mist at pH 2.5, 3.5, 4.5, and 5.5 either alone or in combination with 0.1 ppm 03, S02, and NO2 or NO2 plus S02. After 4 and 8 weeks of treatment, height, leaf area, and leaf and new shoot weight were determined and growth analysis variables calculated. Height, leaf area, and dry weight decreased with...

Blast Mitigation by Water Mist, (3) Mitigation of Confined and Unconfined Blasts

DTIC Science & Technology

2006-07-14

2 (vv)I1 1 j7(T - TJ) (18) In addition to drag, heat transfer, and vaporization, droplet breakup must also be accounted for when large droplets...Mitigation of Confined and Unconfined Blasts Table of Contents 1 . Introduction 2 . Numerical Model and Solution Procedure 2.1 Gas-phase Model 2.2...enclosure at 1 , 2 , 5, and 15 ms after detonation of a 2.12 kg explosive without water mist present. Temperature contour range is from 300 to 2500 K

Intercomparisons of airborne measurements of aerosol ionic chemical composition during TRACE-P and ACE-Asia

NASA Astrophysics Data System (ADS)

Ma, Y.; Weber, R. J.; Maxwell-Meier, K.; Orsini, D. A.; Lee, Y.-N.; Huebert, B. J.; Howell, S. G.; Bertram, T.; Talbot, R. W.; Dibb, J. E.; Scheuer, E.

2004-08-01

As part of the two field studies, Transport and Chemical Evolution over the Pacific (TRACE-P) and the Asian Aerosol Characterization Experiment (ACE-Asia), the inorganic chemical composition of tropospheric aerosols was measured over the western Pacific from three separate aircraft using various methods. Comparisons are made between the rapid online techniques of the particle into liquid sampler (PILS) for measurement of a suite of fine particle a mist chamber/ion chromatograph (MC/IC) measurement of fine sulfate, and the longer time-integrated filter and micro-orifice impactor (MOI) measurements. Comparisons between identical PILS on two separate aircraft flying in formation showed that they were highly correlated (e.g., sulfate r2 of 0.95), but were systematically different by 10 ± 5% (linear regression slope and 95% confidence bounds), and had generally higher concentrations on the aircraft with a low-turbulence inlet and shorter inlet-to-instrument transmission tubing. Comparisons of PILS and mist chamber measurements of fine sulfate on two different aircraft during formation flying had an r2 of 0.78 and a relative difference of 39% ± 5%. MOI ionic data integrated to the PILS upper measurement size of 1.3 μm sampling from separate inlets on the same aircraft showed that for sulfate, PILS and MOI were within 14% ± 6% and correlated with an r2 of 0.87. Most ionic compounds were within ±30%, which is in the range of differences reported between PILS and integrated samplers from ground-based comparisons. In many cases, direct intercomparison between the various instruments is difficult due to differences in upper-size detection limits. However, for this study, the results suggest that the fine particle mass composition measured from aircraft agree to within 30-40%.

Use of a parallel path nebulizer for capillary-based microseparation techniques coupled with an inductively coupled plasma mass spectrometer for speciation measurements

NASA Astrophysics Data System (ADS)

Yanes, Enrique G.; Miller-Ihli, Nancy J.

2004-06-01

A low flow, parallel path Mira Mist CE nebulizer designed for capillary electrophoresis (CE) was evaluated as a function of make-up solution flow rate, composition, and concentration, as well as the nebulizer gas flow rate. This research was conducted in support of a project related to the separation and quantification of cobalamin (vitamin B-12) species using microseparation techniques combined with inductively coupled plasma mass spectrometry (ICP-MS) detection. As such, Co signals were monitored during the nebulizer characterization process. Transient effects in the ICP were studied to evaluate the suitability of using gradients for microseparations and the benefit of using methanol for the make-up solution was demonstrated. Co signal response changed significantly as a function of changing methanol concentrations of the make-up solution and maximum signal enhancement was seen at 20% methanol with a 15 μl/min flow rate. Evaluation of the effect of changing the nebulizer gas flow rates showed that argon flows from 0.8 to 1.2 l/min were equally effective. The Mira Mist CE parallel path nebulizer was then evaluated for interfacing capillary microseparation techniques including capillary electrophoresis (CE) and micro high performance liquid chromatography (μHPLC) to inductively coupled plasma mass spectrometry (ICP-MS). A mixture of four cobalamin species standards (cyanocobalamin, hydroxocobalamin, methylcobalamin, and 5' deoxyadenosylcobalamin) and the corrinoid analogue cobinamide dicyanide were successfully separated using both CE-ICP-MS and μHPLC-ICP-MS using the parallel path nebulizer with a make-up solution containing 20% methanol with a flow rate of 15 μl/min.

Intercomparisons of Airborne Measurements of Aerosol Ionic Chemical Composition during TRACE-P and ACE-Asia

NASA Technical Reports Server (NTRS)

Ma, Y.; Weber, R. J.; Maxwell-Meier, K.; Orsini, D. A.; Lee, Y.-N.; Huebert, B. J.; Howell, S. G.; Bertram, T.; Talbot, R. W.

2003-01-01

As part of the two field studies, Transport and Chemical Evolution over the Pacific (TRACE-P), and the Asian Aerosol Characterization Experiment (ACEAsia), the inorganic chemical composition of tropospheric aerosols was measured over the western Pacific from three separate aircraft using various methods. Comparisons are made between the rapid online techniques of the Particle Into Liquid Sampler (PILS) for measurement of a suite of fine particle ionic compounds and a mist chamber (MC/IC) measurement of fine sulfate, and the longer time-integrated filter and multi-orifice impactor (MOI) measurements. Comparisons between identical PILS on two separate aircraft flying in formation showed that they were highly correlated (e.g., sulfate r(sup 2) of 0.95), but were systematically different by 10 +/- 5% (linear regression slope and 95% confidence bounds), and had generally higher concentrations on the aircraft with a low turbulence inlet and shorter inlet-to-instrument transmission tubing. Comparisons of PILS and mist chamber measurements of fine sulfate on two different aircraft during formation flying had an 3 of 0.78 and a relative difference of 39% +/- 5%. MOI ionic data integrated to the PILS upper measurement size of 1.3 pm sampling from separate inlets on the same aircraft showed that for sulfate, PILS and MOI were within 14% +/- 6% and correlated with an r(sup 2) of 0.87. Most ionic compounds were within f 30%, which is in the range of differences reported between PILS and integrated samplers from ground-based comparisons. In many cases, direct intercomparison between the various instruments is difficult due to differences in upper-size detection limits. However, for this study, the results suggest that the fine particle mass composition measured from aircraft agree to within 30-40%.

Recommendations for the use of mist nets for inventory and monitoring of bird populations

USGS Publications Warehouse

Ralph, C. John; Dunn, Erica H.; Peach, Will J.; Handel, Colleen M.; Ralph, C. John; Dunn, Erica H.

2004-01-01

We provide recommendations on the best practices for mist netting for the purposes of monitoring population parameters such as abundance and demography. Studies should be carefully thought out before nets are set up, to ensure that sampling design and estimated sample size will allow study objectives to be met. Station location, number of nets, type of nets, net placement, and schedule of operation should be determined by the goals of the particular project, and we provide guidelines for typical mist-net studies. In the absence of study-specific requirements for novel protocols, commonly used protocols should be used to enable comparison of results among studies. Regardless of the equipment, net layout, or netting schedule selected, it is important for all studies that operations be strictly standardized, and a well-written operation protocol will help in attaining this goal. We provide recommendations for data to be collected on captured birds, and emphasize the need for good training of project personnel

Viscometric and misting properties of polymer-modified fuel

NASA Technical Reports Server (NTRS)

Grens, E. A., II; Williams, M. C.

1982-01-01

Solutions of polyisobutylenes L160, L200, B200, and B230 in Jet-A were prepared at concentrations up to 3000 ppm. These polymers have molecular weights in the range 5 to 9 x 1,00,000 and have previously been shown to induce anti-misting properties in Jet-A. In connection with the pumpability of such solutions, especially at low temperatures, the shear viscosity, eta, of these solutions was measured at temperatures 25 C, 0 C, and -25 C. Concentration-dependence of eta was very similar for all four polymer solutes, the increase of eta(c) at 3000 ppm being roughly four-fold (relative to Jet-A) for the L-series and five-fold for the B-series. This behavior prevailed at all temperatures, and there was no evidence of phase separation or other chemical instability at -25 C at any concentration. In the more practical c-range for anti-misting applications, say within 1000 ppm, the increase of eta(c) was only twofold.

In vitro antifungal activity of extracts obtained from Hypericum perforatum adventitious roots cultured in a mist bioreactor against planktonic cells and biofilm of Malassezia furfur.

PubMed

Simonetti, Giovanna; Tocci, Noemi; Valletta, Alessio; Brasili, Elisa; D'Auria, Felicia Diodata; Idoux, Alicia; Pasqua, Gabriella

2016-01-01

Xanthone-rich extracts from Hypericum perforatum root cultures grown in a Mist Bioreactor as antifungal agents against Malassezia furfur. Extracts of Hypericum perforatum roots grown in a bioreactor showed activity against planktonic cells and biofilm of Malassezia furfur. Dried biomass, obtained from roots grown under controlled conditions in a ROOTec mist bioreactor, has been extracted with solvents of increasing polarity (i.e. chloroform, ethyl acetate and methanol). The methanolic fraction was the richest in xanthones (2.86 ± 0.43 mg g(-1) DW) as revealed by HPLC. The minimal inhibitory concentration of the methanol extract against M. furfur planktonic cells was 16 μg mL(-1). The inhibition percentage of biofilm formation, at a concentration of 16 μg mL(-1), ranged from 14% to 39%. The results show that H. perforatum root extracts could be used as new antifungal agents in the treatment of Malassezia infections.

Process and apparatus for obtaining silicon from fluosilicic acid

DOEpatents

Sancier, Kenneth M.

1985-07-16

Process for producing low cost, high purity solar grade Si wherein a reduction reaction, preferably the reduction of SiF.sub.4, by an alkali metal (liquid Na preferred) is carried out essentialy continuously by injecting of reactants in substantially stoichiometric proportions into a reaction chamber having a controlled temperature thereby to form a mist or dispersion of reactants. The reactants being supplied at such a rate and temperature that the reaction takes place far enough away from the entry region to avoid plugging of reactants at the entry region, the reaction is completed and whereby essentially all reaction product solidifies and forms a free flowing powder before reaction product hits a reaction chamber wall. Thus, the reaction product does not adhere to the reaction chamber wall or pick up impurities therefrom. Separation of reaction products is easily carried out by either a leach or melt separation process.

Effect of an upstream bulge configuration on film cooling with and without mist injection.

PubMed

Wang, Jin; Li, Qianqian; Sundén, Bengt; Ma, Ting; Cui, Pei

2017-12-01

To meet the economic requirements of power output, the increased inlet temperature of modern gas turbines is above the melting point of the material. Therefore, high-efficient cooling technology is needed to protect the blades from the hot mainstream. In this study, film cooling was investigated in a simplified channel. A bulge located upstream of the film hole was numerically investigated by analysis of the film cooling effectiveness distribution downstream of the wall. The flow distribution in the plate channel is first presented. Comparing with a case without bulge, different cases with bulge heights of 0.1d, 0.3d and 0.5d were examined with blowing ratios of 0.5 and 1.0. Cases with 1% mist injection were also included in order to obtain better cooling performance. Results show that the bulge configuration located upstream the film hole makes the cooling film more uniform, and enhanceslateral cooling effectiveness. Unlike other cases, the configuration with a 0.3d-height bulge shows a good balance in improving the downstream and lateral cooling effectiveness. Compared with the case without mist at M = 0.5, the 0.3d-height bulge with 1% mist injection increases lateral average effectiveness by 559% at x/d = 55. In addition, a reduction of the thermal stress concentration can be obtained by increasing the height of the bulge configuration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Incidence of laryngeal cancer and exposure to acid mists.

PubMed Central

Steenland, K; Schnorr, T; Beaumont, J; Halperin, W; Bloom, T

1988-01-01

To determine the relation between exposure to acid mist and laryngeal cancer, the smoking habits, drinking habits, and incidence of laryngeal cancer of 879 male steelworkers exposed to acid mists during pickling operations was ascertained. Sulphuric acid mist was the primary exposure for most men in this cohort. These men had all worked in a pickling operation for a minimum of six months before 1965, with an average duration of exposure of 9.5 years. Exposures to sulphuric acid in the 1970s averaged about 0.2 mg/m3, and earlier exposures were probably similar. Interviews were conducted with all cohort members or their next of kin in 1986 and medical records of decedents were reviewed. Nine workers were identified who had been diagnosed as having laryngeal cancer, using a conservative case definition that required medical record confirmation for any case among decedents and confirmation by a physician for any case among live individuals. Using data from national surveys of cancer incidence as referent rates, 3.44 laryngeal cancers would have been expected. Excess smoking by the exposed cohort compared with the United States population resulted in an upward adjustment of the expected number of cases of laryngeal cancer to 3.92. The standardised incidence rate ratio for laryngeal cancer was 2.30 (9/3.92), with a one sided p value of 0.01 (assuming a Poisson distribution). The finding of excess laryngeal cancer in this cohort is consistent with four other studies published since 1981. PMID:3203082

Optimization of a mist chamber (Cofer scrubber) for sampling water-soluble organics in air.

PubMed

Spaulding, Reggie S; Talbot, Robert W; Charles, M Judith

2002-04-15

While the atmospheric fate and transport of biogenic and anthropogenic hydrocarbons has been extensively studied, little is known about the behavior of first-, second-, and third generation photo-oxidation products that arise from OH radical oxidation of the parent species. The results of chamber experiments establish that *OH oxidation of biogenic and anthropogenic hydrocarbons yields carbonyls, dicarbonyls, hydroxycarbonyls, and keto-acids. However, little is known about the generation and fate of these products in the ambient atmospheric environment. This is changing because of the advent of methods that rely on 0-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine (PFBHA) derivatization of carbonyls in concert with gas chromatography/ion trap mass spectrometry. Such methods provide the means to identify and quantify water-soluble organics, which historically have been difficult to measure. A limitation of existing sampling methods, however, is the use of devices that require low flow rates (0.5-1 L min(-1)). Accordingly, long sampling times (3-4 h) are needed to obtain pptv-ppbv detection limits. The mist chamber is an attractive device because of the high flow rates (25-70 L min(-1)) compatible with its use. Herein, we evaluate a mist chamber using a flow rate of 25-30 L min(-1) to provide short (10 min) sampling times and pptv limits of detection. The results establish a relationship between the Henry's law constant (KH) and the collection efficiency and demonstrate the suitability of the method to measure analytes with KH > or = 10(3) M atm(-1). Adjusting the pH, adding quaternary ammonium salts, or decreasing the temperature of the collecting solution in the mist chamber did not significantly affect the collection efficiency. We tested the method by sampling photooxidation products of isoprene (glyoxal, methylglyoxal, hydroxyacetone, and glycolaldehyde) in the Blodgett Forest, CA. This is the first report of a study the employs the mist chamberto sample hydroxycarbonyls. The accuracy and the reproducibility of the method were evaluated by the analysis of duplicate samples and field spikes. The mean recovery of field spikes was > or =80%, and the relative standard deviation was < or =22% between duplicate measurements. The detection limits were 48, 15, 7.7, and 2.7 pptv for glycolaldehyde, hydroxyacetone, methylglyoxal, and glyoxal, respectively. This work demonstrates the power of the mist chamber in concert with PFBHA derivatization and mass spectrometry to measure pptv concentrations of water-soluble organics with a sampling time of 10 min.

Development of the International Space Station (ISS) Fine Water Mist (FWM) Portable Fire Extinguisher

NASA Technical Reports Server (NTRS)

Clements, Anna L.

2011-01-01

NASA is developing a Fine Water Mist Portable Fire Extinguisher for use on the International Space Station. The International Space Station presently uses two different types of fire extinguishers: a water foam extinguisher in the Russian Segment, and a carbon dioxide extinguisher in the US Segment and Columbus and Kibo pressurized elements. Changes in emergency breathing equipment make Fine Water Mist operationally preferable. Supplied oxygen breathing systems allow for safe discharge of a carbon dioxide fire extinguisher, without concerns of the crew inhaling unsafe levels of carbon dioxide. But the Portable Breathing Apparatus (PBA) offers no more than 15 minutes of capability, and continued use of hose based supplied oxygen system increases the oxygen content in a fire situation. NASA has developed a filtering respirator cartridge for use in a fire environment. It is qualified to provide up to 90 minutes of capability, and because it is a filtering respirator it does not add oxygen to the environment. The fire response respirator cartridge does not filter carbon dioxide (CO2), so a crew member discharging a CO2 fire extinguisher while wearing this filtering respirator would be at risk of inhaling unsafe levels of CO2. Fine Water Mist extinguishes a fire without creating a large volume of air with reduced oxygen and elevated CO2. From a flight hardware design perspective, the fine water mist fire extinguisher has two major elements: (1) the nozzle and crew interface, and (2) the tank. The nozzle and crew interface has been under development for several years. It has gone through several design iterations, and has been part of more than 400 fire challenge and spray characterizations. The crew and vehicle interface aspects of the design will use the heritage of the CO2 based Portable Fire Extinguisher, to minimize the disruption to the crew and integration impacts to the ISS. The microgravity use environment of the system poses a set of unique design requirements specifically for the tank. The nozzle requirements drive a tank pressure that is 2-5 times higher than any commercially available water mist systems. Microgravity requires deliberate separation of gas and water, facilitated by a bladder, a diaphragm, a piston, or separate tanks. This paper will describe the design details of the tank and the nozzle, and discuss the trade studies that informed the decisions to select the tank and nozzle configuration.

MIUS integration and subsystems test program

NASA Technical Reports Server (NTRS)

Beckham, W. S., Jr.; Shows, G. C.; Redding, T. E.; Wadle, R. C.; Keough, M. B.; Poradek, J. C.

1976-01-01

The MIUS Integration and Subsystems Test (MIST) facility at the Lyndon B. Johnson Space Center was completed and ready in May 1974 for conducting specific tests in direct support of the Modular Integrated Utility System (MIUS). A series of subsystems and integrated tests was conducted since that time, culminating in a series of 24-hour dynamic tests to further demonstrate the capabilities of the MIUS Program concepts to meet typical utility load profiles for a residential area. Results of the MIST Program are presented which achieved demonstrated plant thermal efficiencies ranging from 57 to 65 percent.

Advanced Exploration Systems (AES) Logistics Reduction Project: Crew Clothing Care Process Development. Revision: Basic

NASA Technical Reports Server (NTRS)

Demmler, Morgan; Whitehead, Nickolas; Poritz, Darwin; Orndoff, Evelyne

2017-01-01

This report covers the use of ozone and mist with detergent to develop zero-gravity laundering technology. Different concentrations of detergent with and without ozone were applied to remove odor from t-shirts used during exercise. The fabrics of these shirts were categorized into two groups: hydrophobic (polyester and modacrylic) and hydrophilic (cotton and Merino wool). It was found that applying detergent solution as a mist sufficient to achieve saturation can be effective in eliminating odors from athletically soiled shirts either with or without exposure to ozone.

Oil-air mist lubrication as an emergency system and as a primary lubrication system. [for helicopter engines

NASA Technical Reports Server (NTRS)

Loomis, W. R.

1976-01-01

The feasibility of an emergency aspirator once-through lubrication system was demonstrated as a viable survivability concept for Army helicopter mainshaft engine bearings for periods as long as 30 minutes. It was also shown in an experimental study using a 46-mm bore bearing test machine that an oil-air mist once-through system with auxiliary air cooling is an effective primary lubrication system at speeds up to 2,500,000 DN for extended operating periods of at least 50 hours.

Deposition and post-processing techniques for transparent conductive films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christoforo, Mark Greyson; Mehra, Saahil; Salleo, Alberto

2017-07-04

In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

Development of a Standard Test Scenario to Evaluate the Effectiveness of Portable Fire Extinguishers on Lithium-ion Battery Fires

NASA Technical Reports Server (NTRS)

Juarez, Alfredo; Harper, Susan A.; Hirsch, David B.; Carriere, Thierry

2013-01-01

Many sources of fuel are present aboard current spacecraft, with one especially hazardous source of stored energy: lithium ion batteries. Lithium ion batteries are a very hazardous form of fuel due to their self-sustaining combustion once ignited, for example, by an external heat source. Batteries can become extremely energetic fire sources due to their high density electrochemical energy content that may, under duress, be violently converted to thermal energy and fire in the form of a thermal runaway. Currently, lithium ion batteries are the preferred types of batteries aboard international spacecraft and therefore are routinely installed, collectively forming a potentially devastating fire threat to a spacecraft and its crew. Currently NASA is developing a fine water mist portable fire extinguisher for future use on international spacecraft. As its development ensues, a need for the standard evaluation of various types of fire extinguishers against this potential threat is required to provide an unbiased means of comparing between fire extinguisher technologies and ranking them based on performance.

Evolution of the Mobile Information SysTem (MIST)

NASA Technical Reports Server (NTRS)

Litaker, Harry L., Jr.; Thompson, Shelby; Archer, Ronald D.

2008-01-01

The Mobile Information SysTem (MIST) had its origins in the need to determine whether commercial off the shelf (COTS) technologies could improve intervehicular activities (IVA) on International Space Station (ISS) crew maintenance productivity. It began with an exploration of head mounted displays (HMDs), but quickly evolved to include voice recognition, mobile personal computing, and data collection. The unique characteristic of the MIST lies within its mobility, in which a vest is worn that contains a mini-computer and supporting equipment, and a headband with attachments for a HMD, lipstick camera, and microphone. Data is then captured directly by the computer running Morae(TM) or similar software for analysis. To date, the MIST system has been tested in numerous environments such as two parabolic flights on NASA's C-9 microgravity aircraft and several mockup facilities ranging from ISS to the Altair Lunar Sortie Lander. Functional capabilities have included its lightweight and compact design, commonality across systems and environments, and usefulness in remote collaboration. Human Factors evaluations of the system have proven the MIST's ability to be worn for long durations of time (approximately four continuous hours) with no adverse physical deficits, moderate operator compensation, and low workload being reported as measured by Corlett Bishop Discomfort Scale, Cooper-Harper Ratings, and the NASA Total Workload Index (TLX), respectively. Additionally, through development of the system, it has spawned several new applications useful in research. For example, by only employing the lipstick camera, microphone, and a compact digital video recorder (DVR), we created a portable, lightweight data collection device. Video is recorded from the participants point of view (POV) through the use of the camera mounted on the side of the head. Both the video and audio is recorded directly into the DVR located on a belt around the waist. This data is then transferred to another computer for video editing and analysis. Another application has been discovered using simulated flight, in which, a kneeboard is replaced with mini-computer and the HMD to project flight paths and glide slopes for lunar ascent. As technologies evolve, so will the system and its application for research and space system operations.

Using a Sound Field to Reduce the Risks of Bird-Strike: An Experimental Approach.

PubMed

Swaddle, John P; Ingrassia, Nicole M

2017-07-01

Each year, billions of birds collide with large human-made structures, such as building, towers, and turbines, causing substantial mortality. Such bird-strike, which is projected to increase, poses risks to populations of birds and causes significant economic costs to many industries. Mitigation technologies have been deployed in an attempt to reduce bird-strike, but have been met with limited success. One reason for bird-strike may be that birds fail to pay adequate attention to the space directly in front of them when in level, cruising flight. A warning signal projected in front of a potential strike surface might attract visual attention and reduce the risks of collision. We tested this idea in captive zebra finches (Taeniopygia guttata) that were trained to fly down a long corridor and through an open wooden frame. Once birds were trained, they each experienced three treatments at unpredictable times and in a randomized order: a loud sound field projected immediately in front of the open wooden frame; a mist net (i.e., a benign strike surface) placed inside the wooden frame; and both the loud sound and the mist net. We found that birds slowed their flight approximately 20% more when the sound field was projected in front of the mist net compared with when the mist net was presented alone. This reduction in velocity would equate to a substantial reduction in the force of any collision. In addition to slowing down, birds increased the angle of attack of their body and tail, potentially allowing for more maneuverable flight. Concomitantly, the only cases where birds avoided the mist net occurred in the sound-augmented treatment. Interestingly, the sound field by itself did not demonstrably alter flight. Although our study was conducted in a limited setting, the alterations of flight associated with our sound field has implications for reducing bird-strike in nature and we encourage researchers to test our ideas in field trials. © The Author 2017. Published by Oxford University Press on behalf of the Society for Integrative and Comparative Biology. All rights reserved. For permissions please email: journals.permissions@oup.com.

Nighttime image dehazing using local atmospheric selection rule and weighted entropy for visible-light systems

NASA Astrophysics Data System (ADS)

Park, Dubok; Han, David K.; Ko, Hanseok

2017-05-01

Optical imaging systems are often degraded by scattering due to atmospheric particles, such as haze, fog, and mist. Imaging under nighttime haze conditions may suffer especially from the glows near active light sources as well as scattering. We present a methodology for nighttime image dehazing based on an optical imaging model which accounts for varying light sources and their glow. First, glow effects are decomposed using relative smoothness. Atmospheric light is then estimated by assessing global and local atmospheric light using a local atmospheric selection rule. The transmission of light is then estimated by maximizing an objective function designed on the basis of weighted entropy. Finally, haze is removed using two estimated parameters, namely, atmospheric light and transmission. The visual and quantitative comparison of the experimental results with the results of existing state-of-the-art methods demonstrates the significance of the proposed approach.

Investigation of the impact of high liquid viscosity on jet atomization in crossflow via high-fidelity simulations

NASA Astrophysics Data System (ADS)

Li, Xiaoyi; Gao, Hui; Soteriou, Marios C.

2017-08-01

Atomization of extremely high viscosity liquid can be of interest for many applications in aerospace, automotive, pharmaceutical, and food industries. While detailed atomization measurements usually face grand challenges, high-fidelity numerical simulations offer the advantage to comprehensively explore the atomization details. In this work, a previously validated high-fidelity first-principle simulation code HiMIST is utilized to simulate high-viscosity liquid jet atomization in crossflow. The code is used to perform a parametric study of the atomization process in a wide range of Ohnesorge numbers (Oh = 0.004-2) and Weber numbers (We = 10-160). Direct comparisons between the present study and previously published low-viscosity jet in crossflow results are performed. The effects of viscous damping and slowing on jet penetration, liquid surface instabilities, ligament formation/breakup, and subsequent droplet formation are investigated. Complex variations in near-field and far-field jet penetrations with increasing Oh at different We are observed and linked with the underlying jet deformation and breakup physics. Transition in breakup regimes and increase in droplet size with increasing Oh are observed, mostly consistent with the literature reports. The detailed simulations elucidate a distinctive edge-ligament-breakup dominated process with long surviving ligaments for the higher Oh cases, as opposed to a two-stage edge-stripping/column-fracture process for the lower Oh counterparts. The trend of decreasing column deflection with increasing We is reversed as Oh increases. A predominantly unimodal droplet size distribution is predicted at higher Oh, in contrast to the bimodal distribution at lower Oh. It has been found that both Rayleigh-Taylor and Kelvin-Helmholtz linear stability theories cannot be easily applied to interpret the distinct edge breakup process and further study of the underlying physics is needed.

Effects of isotonic and isometric exercises with mist sauna bathing on cardiovascular, thermoregulatory, and metabolic functions

NASA Astrophysics Data System (ADS)

Iwase, Satoshi; Kawahara, Yuko; Nishimura, Naoki; Nishimura, Rumiko; Sugenoya, Junichi; Miwa, Chihiro; Takada, Masumi

2014-08-01

To clarify the effects of isometric and isotonic exercise during mist sauna bathing on the cardiovascular function, thermoregulatory function, and metabolism, six healthy young men (22 ± 1 years old, height 173 ± 4 cm, weight 65.0 ± 5.0 kg) were exposed to a mist sauna for 10 min at a temperature of 40 °C, and relative humidity of 100 % while performing or not performing ˜30 W of isometric or isotonic exercise. The effect of the exercise was assessed by measuring tympanic temperature, heart rate, systolic and diastolic blood pressure, chest sweat rate, chest skin blood flow, and plasma catecholamine and cortisol, glucose, lactate, and free fatty acid levels. Repeated measures ANOVA showed no significant differences in blood pressure, skin blood flow, sweat rate, and total amount of sweating. Tympanic temperature increased more during isotonic exercise, and heart rate increase was more marked during isotonic exercise. The changes in lactate indicated that fatigue was not very great during isometric exercise. The glucose level indicated greater energy expenditure during isometric exercise. The free fatty acid and catecholamine levels indicated that isometric exercise did not result in very great energy expenditure and stress, respectively. The results for isotonic exercise of a decrease in lactate level and an increase in plasma free fatty acid level indicated that fatigue and energy expenditure were rather large while the perceived stress was comparatively low. We concluded that isotonic exercise may be a more desirable form of exercise during mist sauna bathing given the changes in glucose and free fatty acid levels.

Posttest analysis of MIST Test 3109AA using TRAC-PF1/MOD1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steiner, J.L.; Siebe, D.A.; Boyack, B.E.

This document discusses a posttest calculation and analysis of Multi-loop Integral System Test (MIST) 3109AA as the nominal test for the MIST program. It is a test of a small-break loss-of-coolant accident (SBLOCA) with a scaled 10-cm{sup 2} break in the B1 cold leg. The test exhibited the major post-SBLOCA phenomena, as expected, including depressurization to saturation, intermittent and interrupted loop flow, boiler-condenser mode cooling, refill, and postrefill cooldown. Full high-pressure injection and auxiliary feedwater were available, reactor coolant pumps were not available, and reactor-vessel vent valves and guard heaters were automatically controlled. Constant level control in the steam-generator secondariesmore » was used after steam-generator secondary refill and symmetric steam-generator pressure control was used. We performed the calculation using TRAC-PF1/MODI. Agreement between test data and the calculation was generally reasonable. All major trends and phenomena were correctly predicted. It is believed that the correct conclusions about trends and phenomena will be reached if the code is used in similar applications.« less

Posttest analysis of MIST Test 3109AA using TRAC-PF1/MOD1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steiner, J.L.; Siebe, D.A.; Boyack, B.E.

This document discusses a posttest calculation and analysis of Multi-loop Integral System Test (MIST) 3109AA as the nominal test for the MIST program. It is a test of a small-break loss-of-coolant accident (SBLOCA) with a scaled 10-cm[sup 2] break in the B1 cold leg. The test exhibited the major post-SBLOCA phenomena, as expected, including depressurization to saturation, intermittent and interrupted loop flow, boiler-condenser mode cooling, refill, and postrefill cooldown. Full high-pressure injection and auxiliary feedwater were available, reactor coolant pumps were not available, and reactor-vessel vent valves and guard heaters were automatically controlled. Constant level control in the steam-generator secondariesmore » was used after steam-generator secondary refill and symmetric steam-generator pressure control was used. We performed the calculation using TRAC-PF1/MODI. Agreement between test data and the calculation was generally reasonable. All major trends and phenomena were correctly predicted. It is believed that the correct conclusions about trends and phenomena will be reached if the code is used in similar applications.« less

Evaluation of target scores and benchmarks for the traversal task scenario of the Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) laparoscopy simulator.

PubMed

Hackethal, A; Immenroth, M; Bürger, T

2006-04-01

The Minimally Invasive Surgical Trainer-Virtual Reality (MIST-VR) simulator is validated for laparoscopy training, but benchmarks and target scores for assessing single tasks are needed. Control data for the MIST-VR traversal task scenario were collected from 61 novices who performed the task 10 times over 3 days (1 h daily). Data were collected on the time taken, error score, economy of movement, and total score. Test differences were analyzed through percentage scores and t-tests for paired samples. Improvement was greatest over tests 1 to 5 (improvement: test(1.2), 38.07%; p = 0.000; test(4.5), 10.66%; p = 0.010): between tests 5 and 10, improvement slowed and scores stabilized. Variation in participants' performance fell steadily over the 10 tests. Trainees should perform at least 10 tests of the traversal task-five to get used to the equipment and task (automation phase; target total score, 95.16) and five to stabilize and consolidate performance (test 10 target total score, 74.11).

Conversion of LARSYS III.1 to an IBM 370 computer

NASA Technical Reports Server (NTRS)

Williams, G. N.; Leggett, J.; Hascall, G. A.

1975-01-01

A software system for processing multispectral aircraft or satellite data (LARSYS) was designed and written at the Laboratory for Applications of Remote Sensing at Purdue University. This system, being implemented on an IBM 360/67 computer utilizing the Cambridge Monitor System, is of an interactive nature. TAMU LARSYS maintains the essential capabilities of Purdue's LARSYS. The machine configuration for which it has been converted is an IBM-compatible Amdahl 470V/6 computer utilizing the time sharing option of the currently implemented OS/VS2 Operating System. Due to TSO limitations, the NASA-JSC deliverable TAMU LARSYS is comprised of two parts. Part one is a TSO Control Card Checker for LARSYS control cards, and part two is a batch version of LARSYS. Used together, they afford most of the capabilities of the original LARSYS III.1. Additionally, two programs have been written by TAMU to support LARSYS processing. The first is an ERTS-to-MIST conversion program used to convert ERTS data to the LARSYS input form, the MIST tape. The second is a system runtable code which maintains tape/file location information for the MIST data sets.

Magnetic Field Dependent Charge Transport Studies in Organic Semiconducting Materials

NASA Astrophysics Data System (ADS)

Martin, Jesse

Organic magnetoresistance is a phenomenon that is exhibited by many organic semiconductors. The resistance can change by more than 10 % at room temperature and as little as 10 milli-Tesla (mT) applied magnetic field. The change can be either positive or negative, and is angle invariant with respect to magnetic field orientation. Several theories have been presented to account for this anomalous magnetoresistance, but thus far the magnetoresistance by interconversion of singlets and triplets (MIST) model has been the most successful in explaining the behavior. Despite all the research that has gone into this effect, very few reports have gone to fields above 1 Tesla (T). In this manuscript, several specific predictions made by the MIST mechanism will be tested including qualitative behaviors and a quantitative fitting. Studies have been performed up to 35 T to explore the high field behavior. It will be demonstrated that for the low field regime, the MIST model is in excellent agreement with experiment, but that the high field regime is caused by a separate mechanism, not described by any current theory.

Improved aqueous scrubber for collection of soluble atmospheric trace gases

NASA Technical Reports Server (NTRS)

Cofer, W. R., III; Talbot, R. W.; Collins, V. G.

1985-01-01

A new concentration technique for the extraction and enrichment of water-soluble atmospheric trace gases has been developed. The gas scrubbing technique efficiently extracts soluble gases from a large volume flow rate of air sample into a small volume of refluxed trapping solution. The gas scrubber utilizes a small nebulizing nozzle that mixes the incoming air with an aqueous extracting solution to form an air/droplet mist. The mist provides excellent interfacial surface areas for mass transfer. The resulting mist sprays upward through the reaction chamber until it impinges upon a hydrophobic membrane that virtually blocks the passage of droplets but offers little resistance to the existing gas flow. Droplets containing the scrubbed gases coalesce on the membrane and drip back into the reservoir for further refluxing. After a suitable concentration period, the extracting solution containing the analyte can be withdrawn for analysis. The nebulization-reflex concentration technique is more efficient (maximum flow of gas through the minimum volume of extractant) than conventional bubbler/impinger gas extraction techniques and is offered as an alternative method.

Controlled environment life support system: Growth studies with potatoes

NASA Technical Reports Server (NTRS)

Tibbitts, T. W.; Wheeler, R. M.

1986-01-01

Results of experiments conducted to maximize the productivity of potatoes grown under controlled environmental conditions are discussed. A variety of parameters is examined which affect potato growth, specifically, photoperiod, light intensity, temperature, nitrogen nutrition, carbon dioxide concentration and culture techniques. These experiments were conducted using five different cultivars, Russet Burbank, Norchip, Superior, Kennebec and Norland. To achieve high productivity, three specific objectives were explored: (1) to develop effective cultural procedures, (2) to determine the most effective photoperiod and (3) to develop a mist culture system. It is felt that the productivity obtained in this study is below the maximum that can be obtained. High irradiance levels coupled with tuber-promoting conditions such as cooler temperatures, increased CO2 levels and lowered nitrogen concentrations should allow increases in tuber production. Tuberization appears to be accelerated by short daylengths although final yields are not increased. Mist culture techniques have not yet produced fully developed tubers. The use of supporting media and alteration of the nitrogen content of the mist solution are being explored as a way to allow tubers to develop to maturity.

Liquid metal ion source and alloy

DOEpatents

Clark, Jr., William M.; Utlaut, Mark W.; Behrens, Robert G.; Szklarz, Eugene G.; Storms, Edmund K.; Santandrea, Robert P.; Swanson, Lynwood W.

1988-10-04

A liquid metal ion source and alloy, wherein the species to be emitted from the ion source is contained in a congruently vaporizing alloy. In one embodiment, the liquid metal ion source acts as a source of arsenic, and in a source alloy the arsenic is combined with palladium, preferably in a liquid alloy having a range of compositions from about 24 to about 33 atomic percent arsenic. Such an alloy may be readily prepared by a combustion synthesis technique. Liquid metal ion sources thus prepared produce arsenic ions for implantation, have long lifetimes, and are highly stable in operation.

Urinary and air phthalate concentrations and self-reported use of personal care products among minority pregnant women in New York city.

PubMed

Just, Allan C; Adibi, Jennifer J; Rundle, Andrew G; Calafat, Antonia M; Camann, David E; Hauser, Russ; Silva, Manori J; Whyatt, Robin M

2010-11-01

Diethyl phthalate (DEP) and di-n-butyl phthalate (DnBP) are used extensively in personal care products, including fragrances (DEP) and nail polish (DnBP). Between May 2003 and July 2006, we gathered questionnaire data on the use of seven product categories (deodorant, perfume, hair spray, hair gel, nail polish/polish remover, liquid soap/body wash, and lotion/mist) over 48 h during the third trimester of pregnancy from 186 inner-city women. A 48-h personal air sample was collected and analyzed for DEP and DnBP; a maternal spot urine sample was collected and analyzed for their monoester metabolites, monoethyl phthalate (MEP) and mono-n-butyl phthalate (MnBP), respectively. In all, 97% of air samples and 84% of urine samples were collected within ±2 days of the questionnaire. During the 48 h, 41% of women reported perfume use and 10% reported nail polish/polish remover use. In adjusted analyses, no association was seen between nail product use and air DnBP or urine MnBP concentrations. Women reporting perfume use had 2.3 times higher (95% CI 1.6, 3.3) urinary MEP concentrations. Personal air DEP increased by 7% for each 25% increase in a composite indicator of the six other product categories (P<0.05), but was not associated with perfume use. Air DEP was correlated with urine MEP concentrations only among non-perfume users (r=0.51, P<0.001). Results suggest that perfume use is a significant source of DEP exposure.

Urinary and air phthalate concentrations and self-reported use of personal care products among minority pregnant women in New York City

PubMed Central

Just, Allan C.; Adibi, Jennifer J.; Rundle, Andrew G.; Calafat, Antonia M.; Camann, David E.; Hauser, Russ; Silva, Manori J.; Whyatt, Robin M.

2011-01-01

Diethyl phthalate (DEP) and di-n-butyl phthalate (DnBP) are used extensively in personal care products, including fragrances (DEP) and nail polish (DnBP). Between May 2003 and July 2006, we gathered questionnaire data on use of 7 product categories (deodorant, perfume, hair spray, hair gel, nail polish/polish remover, liquid soap/body wash, lotion/mist) over 48 hours during the 3rd trimester of pregnancy from 186 inner-city women. A 48-hour personal air sample was collected and analyzed for DEP and DnBP; a maternal spot urine sample was collected and analyzed for their monoester metabolites, monoethyl phthalate (MEP) and mono-n-butyl phthalate (MnBP), respectively. Ninety-seven percent of air samples and 84% of urine samples were collected within ±2 days of the questionnaire. During the 48 hours, 41% of women reported perfume use and 10% reported nail polish/polish remover use. In adjusted analyses, no association was seen between nail product use and air DnBP or urine MnBP concentrations. Women reporting perfume use had 2.3 times higher (95% CI 1.6, 3.3) urinary MEP concentrations. Personal air DEP increased 7% for each 25% increase in a composite indicator of the 6 other product categories (p<0.05) but was not associated with perfume use. Air DEP was correlated with urine MEP concentrations only among non-perfume users (r=0.51, p<0.001). Results suggest that perfume use is a significant source of DEP exposure. PMID:20354564

Nanosecond liquid crystalline optical modulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borshch, Volodymyr; Shiyanovskii, Sergij V.; Lavrentovich, Oleg D.

2016-07-26

An optical modulator includes a liquid crystal cell containing liquid crystal material having liquid crystal molecules oriented along a quiescent director direction in the unbiased state, and a voltage source configured to apply an electric field to the liquid crystal material wherein the direction of the applied electric field does not cause the quiescent director direction to change. An optical source is arranged to transmit light through or reflect light off the liquid crystal cell with the light passing through the liquid crystal material at an angle effective to undergo phase retardation in response to the voltage source applying themore » electric field. The liquid crystal material may have negative dielectric anisotropy, and the voltage source configured to apply an electric field to the liquid crystal material whose electric field vector is transverse to the quiescent director direction. Alternatively, the liquid crystal material may have positive dielectric anisotropy and the voltage source configured to apply an electric field to the liquid crystal material whose electric field vector is parallel with the quiescent director direction.« less

Measurement Instrument for Scientific Teaching (MIST): A Tool to Measure the Frequencies of Research-Based Teaching Practices in Undergraduate Science Courses.

PubMed

Durham, Mary F; Knight, Jennifer K; Couch, Brian A

2017-01-01

The Scientific Teaching (ST) pedagogical framework provides various approaches for science instructors to teach in a way that more closely emulates how science is practiced by actively and inclusively engaging students in their own learning and by making instructional decisions based on student performance data. Fully understanding the impact of ST requires having mechanisms to quantify its implementation. While many useful instruments exist to document teaching practices, these instruments only partially align with the range of practices specified by ST, as described in a recently published taxonomy. Here, we describe the development, validation, and implementation of the Measurement Instrument for Scientific Teaching (MIST), a survey derived from the ST taxonomy and designed to gauge the frequencies of ST practices in undergraduate science courses. MIST showed acceptable validity and reliability based on results from 7767 students in 87 courses at nine institutions. We used factor analyses to identify eight subcategories of ST practices and used these categories to develop a short version of the instrument amenable to joint administration with other research instruments. We further discuss how MIST can be used by instructors, departments, researchers, and professional development programs to quantify and track changes in ST practices. © 2017 M. F. Durham et al. CBE—Life Sciences Education © 2017 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

A comparison of survey methods for documenting presence of Myotis leibii (Eastern Small-Footed Bats) at roosting areas in Western Virginia

USGS Publications Warehouse

Huth, John K.; Silvis, Alexander; Moosman, Paul R.; Ford, W. Mark; Sweeten, Sara E.

2015-01-01

Many aspects of foraging and roosting habitat of Myotis leibii (Eastern Small-Footed Bat), an emergent rock roosting-obligate, are poorly described. Previous comparisons of effectiveness of acoustic sampling and mist-net captures have not included Eastern Small-Footed Bat. Habitat requirements of this species differ from congeners in the region, and it is unclear whether survey protocols developed for other species are applicable. Using data from three overlapping studies at two sampling sites in western Virginia’s central Appalachian Mountains, detection probabilities were examined for three survey methods (acoustic surveys with automated identification of calls, visual searches of rock crevices, and mist-netting) for use in the development of “best practices” for future surveys and monitoring. Observer effects were investigated using an expanded version of visual search data. Results suggested that acoustic surveys with automated call identification are not effective for documenting presence of Eastern Small-Footed Bats on talus slopes (basal detection rate of 0%) even when the species is known to be present. The broadband, high frequency echolocation calls emitted by Eastern Small-Footed Bat may be prone to attenuation by virtue of their high frequencies, and these factors, along with signal reflection, lower echolocation rates or possible misidentification to other bat species over talus slopes may all have contributed to poor acoustic survey success. Visual searches and mist-netting of emergent rock had basal detection probabilities of 91% and 75%, respectively. Success of visual searches varied among observers, but detection probability improved with practice. Additionally, visual searches were considerably more economical than mist-netting.

Induced PTF1a expression in pancreatic ductal adenocarcinoma cells activates acinar gene networks, reduces tumorigenic properties, and sensitizes cells to gemcitabine treatment.

PubMed

Jakubison, Brad L; Schweickert, Patrick G; Moser, Sarah E; Yang, Yi; Gao, Hongyu; Scully, Kathleen; Itkin-Ansari, Pamela; Liu, Yunlong; Konieczny, Stephen F

2018-05-02

Pancreatic acinar cells synthesize, package, and secrete digestive enzymes into the duodenum to aid in nutrient absorption and meet metabolic demands. When exposed to cellular stresses and insults, acinar cells undergo a dedifferentiation process termed acinar-ductal metaplasia (ADM). ADM lesions with oncogenic mutations eventually give rise to pancreatic ductal adenocarcinoma (PDAC). In healthy pancreata, the basic helix-loop-helix (bHLH) factors MIST1 and PTF1a coordinate an acinar-specific transcription network that maintains the highly developed differentiation status of the cells, protecting the pancreas from undergoing a transformative process. However, when MIST1 and PTF1a gene expression is silenced, cells are more prone to progress to PDAC. In this study, we tested whether induced MIST1 or PTF1a expression in PDAC cells could (i) re-establish the transcriptional program of differentiated acinar cells and (ii) simultaneously reduce tumor cell properties. As predicted, PTF1a induced gene expression of digestive enzymes and acinar-specific transcription factors, while MIST1 induced gene expression of vesicle trafficking molecules as well as activation of unfolded protein response components, all of which are essential to handle the high protein production load that is characteristic of acinar cells. Importantly, induction of PTF1a in PDAC also influenced cancer-associated properties, leading to a decrease in cell proliferation, cancer stem cell numbers, and repression of key ATP-binding cassette efflux transporters resulting in heightened sensitivity to gemcitabine. Thus, activation of pancreatic bHLH transcription factors rescues the acinar gene program and decreases tumorigenic properties in pancreatic cancer cells, offering unique opportunities to develop novel therapeutic intervention strategies for this deadly disease. © 2018 The Authors. Published by FEBS Press and John Wiley & Sons Ltd.

Retrieval cue and delay interval influence the relationship between prospective memory and activities of daily living in older adults.

PubMed

Tierney, Savanna M; Bucks, Romola S; Weinborn, Michael; Hodgson, Erica; Woods, Steven Paul

2016-01-01

Older adults commonly experience mild declines in everyday functioning and the strategic aspects of prospective memory (PM). This study used multiprocess theory to examine whether the strategic demands of retrieval cue type (event vs. time based) and delay interval length (2 vs. 15 min) influence the relationship between PM and activities of daily living (ADLs) in older adults. Participants included 97 community-dwelling older adults recruited from the Western Australia Participant Pool. Participants were administered the Memory for Intentions Screening Test (MIST) and Prospective and Retrospective Memory Questionnaire (PRMQ) as part of a larger neurocognitive assessment. A knowledgeable informant completed the Activities of Daily Living Questionnaire (ADLQ), from which a cutpoint of ≥ 1 was used to classify participants into "ADL normal" (n = 37) or "mild ADL problems" (n = 60) groups. Repeated measures multivariate analysis of variance (MANOVA) controlling for age was conducted with ADL group as the between-subjects factor and either MIST or PRMQ cue and delay scores as the within-subjects factors. We observed a significant ADL group by PM interaction on the MIST, with pair-wise analyses showing that the mild ADL problems group performed worse than ADL normal participants on the 15-min time-based scale (p < .001, Cohen's d = 0.71). No other MIST or PRMQ cue-delay variable differed between the two ADL groups (ps > .10). Findings indicate that decrements in strategically demanding cue monitoring and detection over longer PM delays may partly explain older adults' mild problems in everyday functioning. Findings may inform neuropsychological interventions aimed at maintaining ADL independence and enhancing quality of life in older adults.

Short-term dynamics of causal information transfer in thalamocortical networks during natural inputs and microstimulation for somatosensory neuroprosthesis

PubMed Central

Semework, Mulugeta; DiStasio, Marcello

2014-01-01

Recording the activity of large populations of neurons requires new methods to analyze and use the large volumes of time series data thus created. Fast and clear methods for finding functional connectivity are an important step toward the goal of understanding neural processing. This problem presents itself readily in somatosensory neuroprosthesis (SSNP) research, which uses microstimulation (MiSt) to activate neural tissue to mimic natural stimuli, and has the capacity to potentiate, depotentiate, or even destroy functional connections. As the aim of SSNP engineering is artificially creating neural responses that resemble those observed during natural inputs, a central goal is describing the influence of MiSt on activity structure among groups of neurons, and how this structure may be altered to affect perception or behavior. In this paper, we demonstrate the concept of Granger causality, combined with maximum likelihood methods, applied to neural signals recorded before, during, and after natural and electrical stimulation. We show how these analyses can be used to evaluate the changing interactions in the thalamocortical somatosensory system in response to repeated perturbation. Using LFPs recorded from the ventral posterolateral thalamus (VPL) and somatosensory cortex (S1) in anesthetized rats, we estimated pair-wise functional interactions between functional microdomains. The preliminary results demonstrate input-dependent modulations in the direction and strength of information flow during and after application of MiSt. Cortico-cortical interactions during cortical MiSt and baseline conditions showed the largest causal influence differences, while there was no statistically significant difference between pre- and post-stimulation baseline causal activities. These functional connectivity changes agree with physiologically accepted communication patterns through the network, and their particular parameters have implications for both rehabilitation and brain—machine interface SSNP applications. PMID:25249973

Surface potential measurement of n-type organic semiconductor thin films by mist deposition via Kelvin probe microscopy

NASA Astrophysics Data System (ADS)

Odaka, Akihiro; Satoh, Nobuo; Katori, Shigetaka

2017-08-01

We partially deposited fullerene (C60) and phenyl-C61-butyric acid methyl ester thin films that are typical n-type semiconductor materials on indium-tin oxide by mist deposition at various substrate temperatures. The topographic and surface potential images were observed via dynamic force microscopy/Kelvin probe force microscopy with the frequency modulation detection method. We proved that the area where a thin film is deposited depends on the substrate temperature during deposition from the topographic images. It was also found that the surface potential depends on the substrate temperature from the surface potential images.

New approach to reducing water consumption in commercial kitchen hood

NASA Astrophysics Data System (ADS)

Asmuin, N.; Pairan, M. R.

2017-09-01

Water mist sprays are used in wide range of application. However it is depend to the spray characteristic to suit the particular application. The modern commercial kitchen hood ventilation system was adopted with the water mist nozzle technology as an additional tool to increase the filtration efficiency. However, low level of filtration effectiveness and high water consumption were the major problems among the Commercial Kitchen Ventilation expert. Therefore, this study aims to develop a new mist spray technology to replacing the conventional KSJB nozzle (KSJB is a nozzle’s name). At the same time, an appropriate recommended location to install the nozzle in kitchen hood system was suggested. An extensive simulation works were carried out to observe the spray characteristics, ANSYS (FLUENT) was used for simulation wise. In the case of nozzle studies, nozzles were tested at 1 bar pressure of water and air. In comparison with conventional nozzles configuration, this new approach suggested nozzle configuration was reduce up to 50% of water consumption, which by adopted 3 numbers of nozzles instead of 6 numbers of nozzles in the commercial kitchen hood system. Therefore, this nozzle will be used in industry for their benefits of water consumption, filtration efficiency and reduced the safety limitations.

Sampling and analysis of hexavalent chromium during exposure to chromic acid mist and welding fumes.

PubMed

Blomquist, G; Nilsson, C A; Nygren, O

1983-12-01

Sampling and analysis of hexavalent chromium during exposure to chromic acid mist and welding fumes. Scand j work environ & health 9 (1983) 489-495. In view of the serious health effects of hexavalent chromium, the problems involved in its sampling and analysis in workroom air have been the subject of much concern. In this paper, the stability problems arising from the reduction of hexavalent to trivalent chromium during sampling, sample storage, and analysis are discussed. Replacement of sulfuric acid by a sodium acetate buffer (pH 4) as a leaching solution prior to analysis with the diphenylcarbazide (DPC) method is suggested and is demonstrated to be necessary in order to avoid reduction. Field samples were taken from two different industrial processes-manual metal arc welding on stainless steel without shield gas and chromium plating. A comparison was made of the DPC method, acidic dissolution with atomic absorption spectrophotometric (AAS) analysis, and the carbonate method. For chromic acid mist, the DPC method and AAS analysis were shown to give the same results. In the analysis of welding fumes, the modified DPC method gave the same results as the laborious and less sensitive carbonate method.

STS-107 Flight Day 15 Highlights

NASA Astrophysics Data System (ADS)

2003-01-01

This video shows the activities of the STS-107 crew on flight day 15 of the Columbia orbiter's final mission. The crew includes Commander Rick Husband, Pilot William McCool, Mission Specialists Michael Anderson, David Brown, Laurel Clark, and Kalpana Chawla, and Payload Specialist Ilan Ramon. The primary activities of flight day 15 are crew interviews, and operating the Water Mist Fire Suppression (MIST) experiment. Early in the video, astronauts McCool and Ramon respond together to a question. Much of the video is taken up by an interview of astronauts Brown, Anderson, and McCool. Two parts of the video show the MIST experiment in operation, operated the first time by astronaut Brown. Another part of the video is narrated by Mission Specialist Clark, who identifies views of Mount Vesuvius, and an atoll in the south Pacific. In this part, Payload Specialist Ramon is seen on an exercise machine, Commander Husband shows body fluid samples from the crew taken during the mission, and Clark demonstrates how the crew eats meals. The video ends with footage from earlier in the mission which shows a deployed radiator in the shuttle's payload bay that reflects an image of the Earth.

Embedded Systems Hardware Integration and Code Development for Maraia Capsule and E-MIST

NASA Technical Reports Server (NTRS)

Carretero, Emmanuel S.

2015-01-01

The cost of sending large spacecraft to orbit makes them undesirable for carrying out smaller scientific missions. Small spacecraft are more economical and can be tailored for missions where specific tasks need to be carried out, the Maraia capsule is such a spacecraft. Maraia will allow for samples of experiments conducted on the International Space Station to be returned to earth. The use of balloons to conduct experiments at the edge of space is a practical approach to reducing the large expense of using rockets. E-MIST is a payload designed to fly on a high altitude balloon. It can maintain science experiments in a controlled manner at the edge of space. The work covered here entails the integration of hardware onto each of the mentioned systems and the code associated with such work. In particular, the resistance temperature detector, pressure transducers, cameras, and thrusters for Maraia are discussed. The integration of the resistance temperature detectors and motor controllers to E-MIST is described. Several issues associated with sensor accuracy, code lock-up, and in-flight reset issues are mentioned. The solutions and proposed solutions to these issues are explained.

Development of advanced technologies for biomass pyrolysis

NASA Astrophysics Data System (ADS)

Xu, Ran

The utilization of biomass resources as a renewable energy resource is of great importance in responding to concerns over the protection of the environment and the security of energy supply. This PhD research focuses on the investigation of the conversion of negative value biomass residues into value-added fuels through flash pyrolysis. Pyrolysis Process Study. A pilot plant bubbling fluidized bed pyrolyzer has been set up and extensively used to thermally crack various low or negative value agricultural, food and biofuel processing residues to investigate the yields and quality of the liquid [bio-oil] and solid (bio-char] products. Another novel aspect of this study is the establishment of an energy balance from which the thermal self-sustainability of the pyrolysis process can be assessed. Residues such as grape skins and mixture of grape skins and seeds, dried distiller's grains from bio-ethanol plants, sugarcane field residues (internal bagasse, external and whole plant) have been tested. The pyrolysis of each residue has been carried out at temperatures ranging from 300 to 600°C and at different vapor residence times, to determine its pyrolysis behavior including yields and the overall energy balance. The thermal sustainability of the pyrolysis process has been estimated by considering the energy contribution of the product gases and liquid bio-oll in relation to the pyrolysis heat requirements. The optimum pyrolysis conditions have been identified in terms of maximizing the liquid blo-oil yield, energy density and content of the product blo-oil, after ensuring a self-sustainable process by utilizing the product gases and part of char or bio-oil as heat sources. Adownflow pyrolyzer has also been set up. Preliminary tests have been conducted using much shorter residence times. Bio-oil Recovery. Bio-oil recovery from the pyrolysis unit includes condensation followed by demisting. A blo-oil cyclonic condensing system is designed A nearly tangential entry forces the entering vapors and gases to spin, providing good heat transfer and driving the condensed droplets to the wall through cyclonic action. This condenser design has been successfully demonstrated for the application on the pilot fluidized bed pyrolysis unit. After condensation, a stable aerosol is also typically formed which is difficult to be efficiently captured with conventional technologies. A pilot scale helicoidal rotary demister, a novel technology for removing persistent fine bio-oil droplets from gases using dynamic centrifugal forces, has been developed. The demister uses a helicoidal element, which consists of a metal sheet wound as a spiral, designed to rotate at high speeds within a cyclone body. Larger droplets are separated as they enter the cyclone housing, while the smaller droplets are carried by the gas into the helicoidal path of the rotating element, where they are centrifuged towards the outer collecting walls and, as a result of a specially designed baffle, may flow counter-currently to the gas and are drained out from the bottom of the rotating element. The mist-free gas leaves through a channel located at the center of the spiral. This unique demister design has demonstrated a high separation efficiency when tested offline with artificial submicron mist and tested online for demisting bio-oil aerosol on the pyrolysis unit. Bio-oil Upgrading: Very often, phase separation of bio-oil occurs naturally upon condensation of the bio-oil vapors, typically through the use of cyclonic condensers. The bio-oil is separated into an organic phase and an aqueous phase. Research has been conducted on the possibility to enhance the fuel properties and energy performance of the organic phase by reducing its water content, enhancing its heating value and improving its stability. Through the use of drying agents, a remarkable reduction of water content and an increase of heating value can be achieved. Moreover, the volumetric energy density can be greatly enhanced. Besides, the energy yield of the process has also been investigated. (Abstract shortened by UMI.)

System using electric furnace exhaust gas to preheat scrap for steelmaking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Takai, K.; Iwasaki, K.

1987-09-08

A method is described for clean preheating of scrap contaminated with oil and organic matter, for steelmaking, using heat from exhaust gas flow from an electric furnace. It consists of: burning any combustibles present in the exhaust gas flow and simultanously separating out dust particles from the exhaust gas flow; heating a predetermined amount of the scrap by heat exchange with a predetermined portion of the exhaust gas flow; removing and collecting dust from the exhaust gas flow after preheating of scrap thereby; sensing the temperature of the exhaust flow; scrubbing the exhaust gas flow with an aqueous solution ofmore » a deodorant solvent flowing at a rate regulated to be in a predetermined relationship related to the exhaust gas temperature sensed prior to scrubbing, thereby generating saturated vapor and reducing the temperature of the exhaust gas flow by a predetermined amount; and electrostatically precipitating out oil mist attached to saturated water vapor and liquid droplets in the exhaust gas flow.« less

Bioinspired Antifreeze Secreting Frost-Responsive Pagophobic Coatings

NASA Astrophysics Data System (ADS)

Sun, Xiaoda; Damle, Viraj; Rykaczewski, Konrad

2014-11-01

Prevention of ice and frost accumulation is of interest to transportation, power generation, and agriculture industries. Superhydrophobic and lubricant impregnated pagophobic coatings have been proposed, however, they both fail in frosting conditions. Inspired by functional liquid secretion in natural systems, such as toxin secretion by poison dart frost in response to predator presence, we developed frost-responsive antifreeze secreting pagophobic coatings. These are bi-layered coatings with an inner superhydrophilic ``dermis'' infused with antifreeze and an outer permeable superhydrophobic ``epidermis.'' The superhydrophobic epidermis separates the antifreeze from the environment and prevents ice accumulation by repelling impinging water droplets. In frosting conditions, the antifreeze is secreted from the dermis through pores in the epidermis either due to contact with condensed droplets or temporary switch of the epidermis wettability from hydrophobic to hydrophilic caused by surface icing. Here we demonstrate superior performance of this multifunctional coating in simulated frosting, freezing mist/fog, and freezing spray/rain conditions. KR acknowledges startup funding from ASU.

The use of fermentation liquid of wastewater primary sedimentation sludge as supplemental carbon source for denitrification based on enhanced anaerobic fermentation.

PubMed

Liu, Feng; Tian, Yu; Ding, Yi; Li, Zhipeng

2016-11-01

Wastewater primary sedimentation sludge was prepared into fermentation liquid as denitrification carbon source, and the main components of fermentation liquid was short-chain volatile fatty acids. Meanwhile, the acetic acid and propionic acid respectively accounted for about 29.36% and 26.56% in short-chain volatile fatty acids. The performance of fermentation liquid, methanol, acetic acid, propionic acid and glucose used as sole carbon source were compared. It was found that the denitrification rate with fermentation liquid as carbon source was 0.17mgNO3(-)-N/mg mixed liquor suspended solid d, faster than that with methanol, acetic acid, and propionic acid as sole carbon source, and lower than that with glucose as sole carbon source. For the fermentation liquid as carbon source, the transient accumulation of nitrite was insignificantly under different initial total nitrogen concentration. Therefore, the use of fermentation liquid for nitrogen removal could improve denitrification rate, and reduce nitrite accumulation in denitrification process. Copyright © 2016 Elsevier Ltd. All rights reserved.

Compilation of Requirements for Safe Handling of Fluorine and Fluorine-Containing Products of Uranium Hexafluoride Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferrada, J.J.

2000-04-03

Public Law (PL) 105-204 requires the U.S. Department of Energy to develop a plan for inclusion in the fiscal year 2000 budget for conversion of the Department's stockpile of depleted uranium hexafluoride (DUF{sub 6}) to a more stable form over an extended period. The conversion process into a more stable form will produce fluorine compounds (e.g., elemental fluorine or hydrofluoric acid) that need to be handled safely. This document compiles the requirements necessary to handle these materials within health and safety standards, which may apply in order to ensure protection of the environment and the safety and health of workersmore » and the public. Fluorine is a pale-yellow gas with a pungent, irritating odor. It is the most reactive nonmetal and will react vigorously with most oxidizable substances at room temperature, frequently with ignition. Fluorine is a severe irritant of the eyes, mucous membranes, skin, and lungs. In humans, the inhalation of high concentrations causes laryngeal spasm and broncospasms, followed by the delayed onset of pulmonary edema. At sublethal levels, severe local irritation and laryngeal spasm will preclude voluntary exposure to high concentrations, unless the individual is trapped or incapacitated. A blast of fluorine gas on the shaved skin of a rabbit causes a second degree burn. Lower concentrations cause severe burns of insidious onset, resulting in ulceration, similar to the effects produced by hydrogen fluoride. Hydrofluoric acid is a colorless, fuming liquid or gas with a pungent odor. It is soluble in water with release of heat. Ingestion of an estimated 1.5 grams produced sudden death without gross pathological damage. Repeated ingestion of small amounts resulted in moderately advanced hardening of the bones. Contact of skin with anhydrous liquid produces severe burns. Inhalation of AHA or aqueous hydrofluoric acid mist or vapors can cause severe respiratory tract irritation that may be fatal. Based on the extreme chemical properties of these chemicals as noted above, fluorine or fluorine compounds must be handled appropriately within the boundaries of many safety requirements for the protection of the environment and the public. This report analyzes the safety requirements that regulatory agencies have issued to handle fluorine or fluorine compounds and lists them in Table 1. Table 1 lists the source of the requirements, the specific section of the source document, and a brief description of the requirements.« less

Microorganism mediated liquid fuels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Troiano, Richard

Herein disclosed is a method for producing liquid hydrocarbon product, the method comprising disintegrating a hydrocarbon source; pretreating the disintegrated hydrocarbon source; solubilizing the disintegrated hydrocarbon source to form a slurry comprising a reactant molecule of the hydrocarbon source; admixing a biochemical liquor into the slurry, wherein the biochemical liquor comprises at least one conversion enzyme configured to facilitate bond selective photo-fragmentation of said reactant molecule of the hydrocarbon source, to form liquid hydrocarbons via enzyme assisted bond selective photo-fragmentation, wherein said conversion enzyme comprises reactive sites configured to restrict said reactant molecule such that photo-fragmentation favorably targets a preselectedmore » internal bond of said reactant molecule; separating the liquid hydrocarbons from the slurry, wherein contaminants remain in the slurry; and enriching the liquid hydrocarbons to form a liquid hydrocarbon product. Various aspects of such method/process are also discussed.« less

Experimental und numerical investigations on cooling efficiency of Air-Mist nozzles on steel during continuous casting

NASA Astrophysics Data System (ADS)

Arth, G.; Taferner, M.; Bernhard, C.; Michelic, S.

2016-07-01

Cooling strategies in continuous casting of steel can vary from rapid cooling to slow cooling, mainly controlled by adjusting the amount of water sprayed onto the surface of the product. Inadequate adjustment however can lead to local surface undercooling or reheating, leading to surface and inner defects. This paper focuses on cooling efficiency of Air-Mist nozzles on casted steel and the experimental and numerical prediction of surface temperature distributions over the product width. The first part explains the determination of heat transfer coefficients (HTC) on laboratory scale, using a so called nozzle measuring stand (NMS). Based on measured water distributions and determined HTC's for air-mist nozzles using the NMS, surface temperatures are calculated by a transient 2D-model on a simple steel plate, explained in the second part of this paper. Simulations are carried out varying water impact density and spray water distribution, consequently influencing the local HTC distribution over the plate width. Furthermore, these results will be interpreted with regard to their consequence for surface and internal quality of the cast product. The results reveal the difficulty of correct adjustment of the amount of sprayed water, concurrent influencing water distribution and thus changing HTC distribution and surface temperature.

Laparoscopic baseline ability assessment by virtual reality.

PubMed

Madan, Atul K; Frantzides, Constantine T; Sasso, Lisa M

2005-02-01

Assessment of any surgical skill is time-consuming and difficult. Currently, there are no accepted metrics for most surgical skills, especially laparoscopic skills. Virtual reality has been utilized for laparoscopic training of surgical residents. Our hypothesis is that this technology can be utilized for laparoscopic ability metrics. This study involved medical students with no previous laparoscopic experience. All students were taken into a porcine laboratory in order to assess two operative tasks (measuring a piece of bowel and placing a piece of bowel into a laparoscopic bag). Then they were taken into an inanimate lab with a Minimally Invasive Surgery Trainer-Virtual Reality (MIST-VR). Each student repeatedly performed one task (placing a virtual reality ball into a receptacle). The students' scores and times from the animate lab were compared with average economy of movement and times from the MIST-VR. The MIST-VR scored both hands individually. Thirty-two first- and second-year medical students were included in the study. There was statistically significant (P < 0.05) correlation between 11 of 16 possible relationships between the virtual reality trainer and operative tasks. While not all of the possible relationships demonstrated statistically significant correlation, the majority of the possible relationships demonstrated statistically significant correlation. Virtual reality may be an avenue for measuring laparoscopic surgical ability.

Emissions of sulfur trioxide from coal-fired power plants.

PubMed

Srivastava, R K; Miller, C A; Erickson, C; Jambhekar, R

2004-06-01

Emissions of sulfur trioxide (SO3) are a key component of plume opacity and acid deposition. Consequently, these emissions need to be low enough to not cause opacity violations and acid deposition. Generally, a small fraction of sulfur (S) in coal is converted to SO3 in coal-fired combustion devices such as electric utility boilers. The emissions of SO3 from such a boiler depend on coal S content, combustion conditions, flue gas characteristics, and air pollution devices being used. It is well known that the catalyst used in the selective catalytic reduction (SCR) technology for nitrogen oxides control oxidizes a small fraction of sulfur dioxide in the flue gas to SO3. The extent of this oxidation depends on the catalyst formulation and SCR operating conditions. Gas-phase SO3 and sulfuric acid, on being quenched in plant equipment (e.g., air preheater and wet scrubber), result in fine acidic mist, which can cause increased plume opacity and undesirable emissions. Recently, such effects have been observed at plants firing high-S coal and equipped with SCR systems and wet scrubbers. This paper investigates the factors that affect acidic mist production in coal-fired electric utility boilers and discusses approaches for mitigating emission of this mist.

Factors affecting microcuttings of Stevia using a mist-chamber propagation box.

PubMed

Osman, Mohamad; Samsudin, Nur Syamimi; Faruq, Golam; Nezhadahmadi, Arash

2013-01-01

Stevia rebaudiana Bertoni is a member of Compositae family. Stevia plant has zero calorie content and its leaves are estimated to be 300 times sweeter than sugar. This plant is believed to be the most ideal substitute for sugar and important to assist in medicinal value especially for diabetic patients. In this study, microcutting techniques using a mist-chamber propagation box were used as it was beneficial for propagation of Stevia and gave genetic uniformity to the plant. The effects of different treatments on root stimulation of Stevia in microcuttings technique were evaluated. Treatments studied were different sizes of shoot cuttings, plant growth regulators, lights, and shades. Data logger was used to record the mean value of humidity (>90% RH), light intensity (673-2045 lx), and temperature (28.6-30.1°C) inside the mist-chamber propagation box. From analysis of variance, there were significant differences between varieties and treatments in parameters studied (P < 0.05). For the size of shoot cuttings treatment, 6 nodes cuttings were observed to increase root number. As compared to control, shoot cuttings treated with indole butyric acid (IBA) had better performance regarding root length. Yellow light and 50% shade treatments showed higher root and leaf number and these conditions can be considered as crucial for potential propagation of Stevia.

Evaluation of three elevated mist-net systems for sampling birds

USGS Publications Warehouse

Meyers, J.M.; Pardieck, K.L.

1993-01-01

Three light-weight, low-canopy mist-net systems were developed and tested in dry tropical scrub, mangrove and forest habitats. One plastic (polyvinyl chloride) and two aluminum pole systems (with and without pulleys) were used to support mist nets to heights of up to 7.3 m. Although the aluminum telescoping-pole system (without pulleys) was expensive initially ( 79-141/unit (US)), its use reduced capture of nontarget species and may have increased capture of target species when compared with ground-level netting. In one year, its use also reduced labor costs by 756, which completely offset the higher cost of the aluminum telescoping-pole system when compared to the plastic-pole system ( 19/unit). Unlike the plastic-pole system, the aluminum telescoping-pole system was adjustable to any height within its range of 1.8 to 7.3 m, was 1.5 m higher, was more efficient to operate in the field, and was easily moved to new locations. For capture of psittacines, the pulleys of the aluminum telescoping-pole system were not necessary, but their use may assist in efficiently retrieving large numbers of birds from the nets. The aluminum telescoping-pole system was efficient in capturing psittacines, columbids, passerines and possibly chiropterans in habitats with canopies lt 10 m or in the forest subcanopy.

Role of atmospheric ammonia in particulate matter formation in Houston during summertime

NASA Astrophysics Data System (ADS)

Gong, Longwen; Lewicki, Rafał; Griffin, Robert J.; Tittel, Frank K.; Lonsdale, Chantelle R.; Stevens, Robin G.; Pierce, Jeffrey R.; Malloy, Quentin G. J.; Travis, Severin A.; Bobmanuel, Loliya M.; Lefer, Barry L.; Flynn, James H.

2013-10-01

Simultaneous high-time-resolution measurements of atmospheric NH3, HNO3, soluble gas-phase chloride, and aerosol species were made in Houston, TX, from August 5, 2010 to August 9, 2010. Gaseous NH3 was measured using a 10.4-μm external cavity quantum cascade laser-based sensor employing conventional photo-acoustic spectroscopy, while gaseous HNO3 and HCl were sampled using a mist chamber-ion chromatograph (IC) system. Particle chemical composition was determined using a particle-into-liquid-sampler-IC system. There was a large amount of variability in the gas phase mixing ratios of NH3 (3.0 ± 2.5 ppb), HNO3 (287.4 ± 291.6 ppt), and HCl (221.3 ± 260.7 ppt). Elevated NH3 levels occurred around mid-day when NH (0.5 ± 1.0 μg m-3) and SO (4.5 ± 4.3 μg m-3) also increased considerably, indicating that NH3 likely influenced aerosol particle mass. By contrast, the formation of NH4NO3 and NH4Cl was not observed during the measurements. Point sources (e.g., power plant and chemical plant) might be potential contributors to the enhancements in NH3 at the measurement site under favorable meteorological conditions. Increased particle number concentrations were predicted by the SAM-TOMAS model downwind of a large coal-fired power plant when NH3 emissions (based on these measurements) were included, highlighting the potential importance of NH3 with respect to particle number concentration. Separate measurements also indicate the role of NH3 in new particle formation in Houston under low-sulfur conditions.

Concentric micro-nebulizer for direct sample insertion

DOEpatents

Fassel, V.A.; Rice, G.W.; Lawrence, K.E.

1984-03-06

A concentric micro-nebulizer and method for introducing liquid samples into a plasma established in a plasma torch including a first tube connected to a source of plasma gas. The concentric micro-nebulizer has inner and outer concentric tubes extending upwardly within the torch for connection to a source of nebulizer gas and to a source of liquid solvent and to a source of sample liquid. The inner tube is connected to the source of liquid solvent and to the source of sample liquid and the outer tube is connected to the source of nebulizer gas. The outer tube has an orifice positioned slightly below the plasma when it is established, with the inner and outer tubes forming an annulus therebetween with the annular spacing between the tubes at said orifice being less than about 0.05mm. The dead volume of the inner tube is less than about 5 microliters.

Concentric micro-nebulizer for direct sample insertion

DOEpatents

Fassel, Velmer A.; Rice, Gary W.; Lawrence, Kimberly E.

1986-03-11

A concentric micro-nebulizer and method for introducing liquid samples into a plasma established in a plasma torch including a first tube connected to a source of plasma gas. The concentric micro-nebulizer has inner and outer concentric tubes extending upwardly within the torch for connection to a source of nebulizer gas and to a source of liquid solvent and to a source of sample liquid. The inner tube is connected to the source of liquid solvent and to the source of sample liquid and the outer tube is connected to the source of nebulizer gas. The outer tube has an orifice positioned slightly below the plasma when it is established, with the inner and outer tubes forming an annulus therebetween with the annular spacing between the tubes at said orifice being less than about 0.05 mm. The dead volume of the inner tube is less than about 5 microliters.

Liquid Water Transport in the Reactant Channels of Proton Exchange Membrane Fuel Cells

NASA Astrophysics Data System (ADS)

Banerjee, Rupak

Water management has been identified as a critical issue in the development of PEM fuel cells for automotive applications. Water is present inside the PEM fuel cell in three phases, i.e. liquid phase, vapor phase and mist phase. Liquid water in the reactant channels causes flooding of the cell and blocks the transport of reactants to the reaction sites at the catalyst layer. Understanding the behavior of liquid water in the reactant channels would allow us to devise improved strategies for removing liquid water from the reactant channels. In situ fuel cell tests have been performed to identify and diagnose operating conditions which result in the flooding of the fuel cell. A relationship has been identified between the liquid water present in the reactant channels and the cell performance. A novel diagnostic technique has been established which utilizes the pressure drop multiplier in the reactant channels to predict the flooding of the cell or the drying-out of the membrane. An ex-situ study has been undertaken to quantify the liquid water present in the reactant channels. A new parameter, the Area Coverage Ratio (ACR), has been defined to identify the interfacial area of the reactant channel which is blocked for reactant transport by the presence of liquid water. A parametric study has been conducted to study the effect of changing temperature and the inlet relative humidity on the ACR. The ACR decreases with increase in current density as the gas flow rates increase, removing water more efficiently. With increase in temperature, the ACR decreases rapidly, such that by 60°C, there is no significant ACR to be reported. Inlet relative humidity of the gases does change the saturation of the gases in the channel, but did not show any significant effect on the ACR. Automotive powertrains, which is the target for this work, are continuously faced with transient changes. Water management under transient operating conditions is significantly more challenging and has not been investigated in detail. This study begins to investigate the effects of changing operating conditions on liquid water transport through the reactant channels. It has been identified that rapidly increasing temperature leads to the dry-out of the membrane and rapidly cooling the cell below 55°C results in the start of cell flooding. In changing the operating load of the PEMFC, overshoot in the pressure drop in the reactant channel has been identified for the first time as part of this investigation. A parametric study has been conducted to identify the factors which influence this overshoot behavior.

Optimizing Sampling Design to Deal with Mist-Net Avoidance in Amazonian Birds and Bats

PubMed Central

Marques, João Tiago; Ramos Pereira, Maria J.; Marques, Tiago A.; Santos, Carlos David; Santana, Joana; Beja, Pedro; Palmeirim, Jorge M.

2013-01-01

Mist netting is a widely used technique to sample bird and bat assemblages. However, captures often decline with time because animals learn and avoid the locations of nets. This avoidance or net shyness can substantially decrease sampling efficiency. We quantified the day-to-day decline in captures of Amazonian birds and bats with mist nets set at the same location for four consecutive days. We also evaluated how net avoidance influences the efficiency of surveys under different logistic scenarios using re-sampling techniques. Net avoidance caused substantial declines in bird and bat captures, although more accentuated in the latter. Most of the decline occurred between the first and second days of netting: 28% in birds and 47% in bats. Captures of commoner species were more affected. The numbers of species detected also declined. Moving nets daily to minimize the avoidance effect increased captures by 30% in birds and 70% in bats. However, moving the location of nets may cause a reduction in netting time and captures. When moving the nets caused the loss of one netting day it was no longer advantageous to move the nets frequently. In bird surveys that could even decrease the number of individuals captured and species detected. Net avoidance can greatly affect sampling efficiency but adjustments in survey design can minimize this. Whenever nets can be moved without losing netting time and the objective is to capture many individuals, they should be moved daily. If the main objective is to survey species present then nets should still be moved for bats, but not for birds. However, if relocating nets causes a significant loss of netting time, moving them to reduce effects of shyness will not improve sampling efficiency in either group. Overall, our findings can improve the design of mist netting sampling strategies in other tropical areas. PMID:24058579

Fine-Water-Mist Multiple-Orientation-Discharge Fire Extinguisher

NASA Technical Reports Server (NTRS)

Butz, James R.; Turchi, Craig S.; Kimball, Amanda; McKinnon, Thomas; Riedel, Edward

2010-01-01

A fine-water-mist fire-suppression device has been designed so that it can be discharged uniformly in any orientation via a high-pressure gas propellant. Standard fire extinguishers used while slightly tilted or on their side will not discharge all of their contents. Thanks to the new design, this extinguisher can be used in multiple environments such as aboard low-gravity spacecraft, airplanes, and aboard vehicles that may become overturned prior to or during a fire emergency. Research in recent years has shown that fine water mist can be an effective alternative to Halons now banned from manufacture. Currently, NASA uses carbon dioxide for fire suppression on the International Space Station (ISS) and Halon chemical extinguishers on the space shuttle. While each of these agents is effective, they have drawbacks. The toxicity of carbon dioxide requires that the crew don breathing apparatus when the extinguishers are deployed on the ISS, and Halon use in future spacecraft has been eliminated because of international protocols on substances that destroy atmospheric ozone. A major advantage to the new system on occupied spacecraft is that the discharged system is locally rechargeable. Since the only fluids used are water and nitrogen, the system can be recharged from stores of both carried aboard the ISS or spacecraft. The only support requirement would be a pump to fill the water and a compressor to pressurize the nitrogen propellant gas. This system uses a gaseous agent to pressurize the storage container as well as to assist in the generation of the fine water mist. The portable fire extinguisher hardware works like a standard fire extinguisher with a single storage container for the agents (water and nitrogen), a control valve assembly for manual actuation, and a discharge nozzle. The design implemented in the proof-of-concept experiment successfully extinguished both open fires and fires in baffled enclosures.

Method and apparatus for electrokinetic co-generation of hydrogen and electric power from liquid water microjets

DOEpatents

Saykally, Richard J; Duffin, Andrew M; Wilson, Kevin R; Rude, Bruce S

2013-02-12

A method and apparatus for producing both a gas and electrical power from a flowing liquid, the method comprising: a) providing a source liquid containing ions that when neutralized form a gas; b) providing a velocity to the source liquid relative to a solid material to form a charged liquid microjet, which subsequently breaks up into a droplet spay, the solid material forming a liquid-solid interface; and c) supplying electrons to the charged liquid by contacting a spray stream of the charged liquid with an electron source. In one embodiment, where the liquid is water, hydrogen gas is formed and a streaming current is generated. The apparatus comprises a source of pressurized liquid, a microjet nozzle, a conduit for delivering said liquid to said microjet nozzle, and a conductive metal target sufficiently spaced from said nozzle such that the jet stream produced by said microjet is discontinuous at said target. In one arrangement, with the metal nozzle and target electrically connected to ground, both hydrogen gas and a streaming current are generated at the target as it is impinged by the streaming, liquid spray microjet.

TRAC-PF1/MOD1 support calculations for the MIST/OTIS program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fujita, R.K.; Knight, T.D.

1984-01-01

We are using the Transient Reactor Analysis Code (TRAC), specifically version TRAC-PF1/MOD1, to perform analyses in support of the MultiLoop Integral-System Test (MIST) and the Once-Through Integral-System (OTIS) experiment program. We have analyzed Geradrohr Dampferzeuger Anlage (GERDA) Test 1605AA to benchmark the TRAC-PF1/MOD1 code against phenomena expected to occur in a raised-loop B and W plant during a small-break loss-of-coolant accident (SBLOCA). These results show that the code can calculate both single- and two-phase natural circulation, flow interruption, boiler-condenser-mode (BCM) heat transfer, and primary-system refill in a B and W-type geometry with low-elevation auxiliary feedwater. 19 figures, 7 tables.

STS-107 Crew Interviews: Kalpana Chawla MS2

NASA Technical Reports Server (NTRS)

2002-01-01

STS-107 Mission Specialist 2 Kalpana Chawla is seen during this preflight interview where she gives a quick overview of the mission before answering questions about her inspiration to become an astronaut and her career path. Chawla outlines her role in the mission in general, and specifically in conducting the on-board science experiments. She discusses the following experiments in detail: MEIDEX (Mediterranean Israel Dust Experiment), CM2 (Combustion Module 2), MIST (Water Mist Fire Suppression), SOFBALL (Structures of Flame Balls at Low Lewis-Number), LSP (Laminar Soot Processes), MGM (Mechanics of Granular Materials) and BDS (Biotechnology Demonstration System). She also discusses the potential benefits of space research, the dual-work shift of the mission and the rewards of international cooperation.

Electrospray ion source with reduced analyte electrochemistry

DOEpatents

Kertesz, Vilmos [Knoxville, TN; Van Berkel, Gary [Clinton, TN

2011-08-23

An electrospray ion (ESI) source and method capable of ionizing an analyte molecule without oxidizing or reducing the analyte of interest. The ESI source can include an emitter having a liquid conduit, a working electrode having a liquid contacting surface, a spray tip, a secondary working electrode, and a charge storage coating covering partially or fully the liquid contacting surface of the working electrode. The liquid conduit, the working electrode and the secondary working electrode can be in liquid communication. The electrospray ion source can also include a counter electrode proximate to, but separated from, said spray tip. The electrospray ion source can also include a power system for applying a voltage difference between the working electrodes and a counter-electrode. The power system can deliver pulsed voltage changes to the working electrodes during operation of said electrospray ion source to minimize the surface potential of the charge storage coating.

Electrospray ion source with reduced analyte electrochemistry

DOEpatents

Kertesz, Vilmos; Van Berkel, Gary J

2013-07-30

An electrospray ion (ESI) source and method capable of ionizing an analyte molecule without oxidizing or reducing the analyte of interest. The ESI source can include an emitter having a liquid conduit, a working electrode having a liquid contacting surface, a spray tip, a secondary working electrode, and a charge storage coating covering partially or fully the liquid contacting surface of the working electrode. The liquid conduit, the working electrode and the secondary working electrode can be in liquid communication. The electrospray ion source can also include a counter electrode proximate to, but separated from, said spray tip. The electrospray ion source can also include a power system for applying a voltage difference between the working electrodes and a counter-electrode. The power system can deliver pulsed voltage changes to the working electrodes during operation of said electrospray ion source to minimize the surface potential of the charge storage coating.

LIF instrument development, in situ measurement at South Pole and one-dimensional air-snowpack modeling of atmospheric nitrous acid (HONO)

NASA Astrophysics Data System (ADS)

Liao, Wei

Atmospheric nitrous acid (HONO) is a significant and sometimes dominant OH source in Polar Regions. In the polar atmosphere, measurements of HONO are an important part of understanding the dynamics of snow-air chemistry and atmospheric photochemistry. The low levels of HONO present in such regions necessitate the development of instrumentation with low detection limits. An improved method of detecting HONO is developed using photo-fragmentation and laser-induced fluorescence. The detection limit of this method is 2-3 pptv for ten-minute integration time with 35% uncertainty. The ANTCI 2003 measurements confirm the high N oxides observed previously in ISCAT 1998 and 2000. The median LIF observed mixing ratio of HONO 10m above the snow was 5.8 pptv (mean value 6.3 pptv) with a maximum of 18.2pptv on Nov 30th, Dec 1st, 3rd, 15th, 17th, 21st, 22nd, 25th, 27th and 28th. The LIF HONO observations are compared to concurrent HONO observations performed by mist chamber/ion chromatography (MC/IC). Both the LIF and MC/IC techniques observed enhanced HONO; however, the MC/IC observations were higher than the LIF observations by a factor of 7.2+/-2.3 in the median. It is suggested that the MC/IC technique might suffer from interference from HNO4. As in ISCAT 2000, the abundance of both HONO measurements exceeds the pure gas phase model predictions, with LIF higher than the pure gas phase model by a factor of 1.92+/-0.67, which implies snow emission of HONO must occur. The LIF measured HONO concentrations are not high enough to significantly influence the NOx budget during ANTCI 2003, but will increase the modeled HOx over-prediction by 28%+/-15% and lead to a dramatic over-prediction of measured OH by 157%+/-35%. Given the short lifetime of HONO, these differences are hard to reconcile with observed low OH levels unless there is a missing HO x sink. It appears, however, that HONO competes with O3 and HCHO as the dominant source of OH at South Pole during ANTCI 2003. Since pure gas phase chemistry cannot account for the measured high concentration of HONO, a 1D air-snowpack model of HONO was developed and constrained by observed chemistry and meteorology data. The 1D model includes pure gas phase chemical mechanisms, molecular diffusion and mechanical dispersion, windpumping in snow, gas phase to quasi-liquid layer phase HONO transfer and quasiliquid layer nitrate photolysis. Photolysis of nitrate is important as a dominant HONO source inside the snowpack, however, the observed HONO emission from the snowpack is triggered mainly by the equilibrium between quasi liquid layer nitrite and firn air HONO deep down in the snow surface (i.e. 30 cm below snow surface). The high concentration HONO in the firn air is subsequently transported above the snowpack by diffusion and windpumping. Given the limited ANTCI 2003 field measurements of pH and nitrite snowpack concentrations, snow emission of HONO is highly likely and will be transported to 10 meters above the snow, where GT LIF measured high HONO concentration. The pH and thickness of the quasi liquid layer along with continuous nitrite measurement are key factors to calibrate and validate the air snowpack model.

Deriving habitat models for northern long-eared bats from historical detection data: A case study using the Fernow Experimental Forest

USGS Publications Warehouse

Ford, W. Mark; Silvis, Alexander; Rodrigue, Jane L.; Kniowski, Andrew B.; Johnson, Joshua B.

2016-01-01

The listing of the northern long-eared bat (Myotis septentrionalis) as federally threatened under the Endangered Species Act following severe population declines from white-nose syndrome presents considerable challenges to natural resource managers. Because the northern long-eared bat is a forest habitat generalist, development of effective conservation measures will depend on appropriate understanding of its habitat relationships at individual locations. However, severely reduced population sizes make gathering data for such models difficult. As a result, historical data may be essential in development of habitat models. To date, there has been little evaluation of how effective historical bat presence data, such as data derived from mist-net captures, acoustic detection, and day-roost locations, may be in developing habitat models, nor is it clear how models created using different data sources may differ. We explored this issue by creating presence probability models for the northern long-eared bat on the Fernow Experimental Forest in the central Appalachian Mountains of West Virginia using a historical, presence-only data set. Each presence data type produced outputs that were dissimilar but that still corresponded with known traits of the northern long-eared bat or are easily explained in the context of the particular data collection protocol. However, our results also highlight potential limitations of individual data types. For example, models from mist-net capture data only showed high probability of presence along the dendritic network of riparian areas, an obvious artifact of sampling methodology. Development of ecological niche and presence models for northern long-eared bat populations could be highly valuable for resource managers going forward with this species. We caution, however, that efforts to create such models should consider the substantial limitations of models derived from historical data, and address model assumptions.

Influence of fine water droplets to temperature and humidity

NASA Astrophysics Data System (ADS)

Hafidzal, M. H. M.; Hamzah, A.; Manaf, M. Z. A.; Saadun, M. N. A.; Zakaria, M. S.; Roslizar, A.; Jumaidin, R.

2015-05-01

Excessively dry air can cause dry skin, dry eyes and exacerbation of medical conditions. Therefore, many researches have been done in order to increase humidity in our environment. One of the ways is by using water droplets. Nowadays, it is well known in market stand fan equipped with water mister in order to increase the humidity of certain area. In this study, the same concept is applied to the ceiling fan. This study uses a model that combines a humidifier which functions as cooler, ceiling fan and scaled down model of house. The objective of this study is to analyze the influence of ceiling fan humidifier to the temperature and humidity in a house. The mechanism of this small model uses batteries as the power source, connected to the fan and the humidifier. The small water tank's function is to store and supply water to the humidifier. The humidifier is used to cool the room by changing water phase to fine water droplets. Fine water droplets are created from mechanism of the humidifier, which is by increasing the kinetic energy of water molecule using high frequency vibration that overcome the holding force between water molecules. Thus, the molecule of water will change to state of gas or mist. The fan is used to spread out the mist of water to surrounding of the room in order to enhance the humidity. Thermocouple and humidity meter are used to measure temperature and humidity in some period of times. The result shows that humidity increases and temperature decreases with time. This application of water droplet can be applied in the vehicles and engine in order to decrease the temperature.

Methane and carbon dioxide emission from two pig finishing barns.

PubMed

Ni, Ji-Qin; Heber, Albert J; Lim, Teng Teeh; Tao, Pei Chun; Schmidt, Amy M

2008-01-01

Agricultural activities are an important source of greenhouse gases. However, comprehensive, long-term, and high-quality measurement data of these gases are lacking. This article presents a field study of CH(4) and CO(2) emission from two 1100-head mechanically ventilated pig (Sus scrofa) finishing barns (B1 and B2) with shallow manure flushing systems and propane space heaters from August 2002 to July 2003 in northern Missouri. Barn 2 was treated with soybean oil sprinkling, misting essential oils, and misting essential oils with water to reduce air pollutant emissions. Only days with CDFB (complete-data-full-barn), defined as >80% of valid data during a day with >80% pigs in the barns, were used. The CH(4) average daily mean (ADM) emission rates were 36.2 +/- 2.0 g/d AU (ADM +/- 95% confidence interval; animal unit = 500 kg live mass) from B1 (CDFB days = 134) and 28.8 +/- 1.8 g/d AU from B2 (CDFB days = 131). The CO(2) ADM emission rates were 17.5 +/- 0.8 kg/d AU from B1 (CDFB days = 146) and 14.2 +/- 0.6 kg/d AU from B2 (CDFB days = 137). The treated barn reduced CH(4) emission by 20% (P < 0.01) and CO(2) emission by 19% (P < 0.01). The CH(4) and CO(2) released from the flushing lagoon effluent were equivalent to 9.8 and 4.1% of the CDFB CH(4) and CO(2) emissions, respectively. The emission data were compared with the literature, and the characteristics of CH(4) and CO(2) concentrations and emissions were discussed.

Bootstrapping a de-identification system for narrative patient records: cost-performance tradeoffs.

PubMed

Hanauer, David; Aberdeen, John; Bayer, Samuel; Wellner, Benjamin; Clark, Cheryl; Zheng, Kai; Hirschman, Lynette

2013-09-01

We describe an experiment to build a de-identification system for clinical records using the open source MITRE Identification Scrubber Toolkit (MIST). We quantify the human annotation effort needed to produce a system that de-identifies at high accuracy. Using two types of clinical records (history and physical notes, and social work notes), we iteratively built statistical de-identification models by annotating 10 notes, training a model, applying the model to another 10 notes, correcting the model's output, and training from the resulting larger set of annotated notes. This was repeated for 20 rounds of 10 notes each, and then an additional 6 rounds of 20 notes each, and a final round of 40 notes. At each stage, we measured precision, recall, and F-score, and compared these to the amount of annotation time needed to complete the round. After the initial 10-note round (33min of annotation time) we achieved an F-score of 0.89. After just over 8h of annotation time (round 21) we achieved an F-score of 0.95. Number of annotation actions needed, as well as time needed, decreased in later rounds as model performance improved. Accuracy on history and physical notes exceeded that of social work notes, suggesting that the wider variety and contexts for protected health information (PHI) in social work notes is more difficult to model. It is possible, with modest effort, to build a functioning de-identification system de novo using the MIST framework. The resulting system achieved performance comparable to other high-performing de-identification systems. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Factors Affecting Microcuttings of Stevia Using a Mist-Chamber Propagation Box

PubMed Central

Osman, Mohamad; Samsudin, Nur Syamimi; Faruq, Golam

2013-01-01

Stevia rebaudiana Bertoni is a member of Compositae family. Stevia plant has zero calorie content and its leaves are estimated to be 300 times sweeter than sugar. This plant is believed to be the most ideal substitute for sugar and important to assist in medicinal value especially for diabetic patients. In this study, microcutting techniques using a mist-chamber propagation box were used as it was beneficial for propagation of Stevia and gave genetic uniformity to the plant. The effects of different treatments on root stimulation of Stevia in microcuttings technique were evaluated. Treatments studied were different sizes of shoot cuttings, plant growth regulators, lights, and shades. Data logger was used to record the mean value of humidity (>90% RH), light intensity (673–2045 lx), and temperature (28.6–30.1°C) inside the mist-chamber propagation box. From analysis of variance, there were significant differences between varieties and treatments in parameters studied (P < 0.05). For the size of shoot cuttings treatment, 6 nodes cuttings were observed to increase root number. As compared to control, shoot cuttings treated with indole butyric acid (IBA) had better performance regarding root length. Yellow light and 50% shade treatments showed higher root and leaf number and these conditions can be considered as crucial for potential propagation of Stevia. PMID:24470797

Virtual reality computer simulation.

PubMed

Grantcharov, T P; Rosenberg, J; Pahle, E; Funch-Jensen, P

2001-03-01

Objective assessment of psychomotor skills should be an essential component of a modern surgical training program. There are computer systems that can be used for this purpose, but their wide application is not yet generally accepted. The aim of this study was to validate the role of virtual reality computer simulation as a method for evaluating surgical laparoscopic skills. The study included 14 surgical residents. On day 1, they performed two runs of all six tasks on the Minimally Invasive Surgical Trainer, Virtual Reality (MIST VR). On day 2, they performed a laparoscopic cholecystectomy on living pigs; afterward, they were tested again on the MIST VR. A group of experienced surgeons evaluated the trainees' performance on the animal operation, giving scores for total performance error and economy of motion. During the tasks on the MIST VR, errors and noneconomy of movements for the left and right hand were also recorded. There were significant correlations between error scores in vivo and three of the six in vitro tasks (p < 0.05). In vivo economy scores correlated significantly with non-economy right-hand scores for five of the six tasks and with non-economy left-hand scores for one of the six tasks (p < 0.05). In this study, laparoscopic performance in the animal model correlated significantly with performance on the computer simulator. Thus, the computer model seems to be a promising objective method for the assessment of laparoscopic psychomotor skills.

Impact of meteorology on air quality modeling over the Po valley in northern Italy

NASA Astrophysics Data System (ADS)

Pernigotti, D.; Georgieva, E.; Thunis, P.; Bessagnet, B.

2012-05-01

A series of sensitivity tests has been performed using both a mesoscale meteorological model (MM5) and a chemical transport model (CHIMERE) to better understand the reasons why all models underestimate particulate matter concentrations in the Po valley in winter. Different options are explored to nudge meteorological observations from regulatory networks into MM5 in order to improve model performances, especially during the low wind speed regimes frequently present in this area. The sensitivity of the CHIMERE modeled particulate matter concentrations to these different meteorological inputs are then evaluated for the January 2005 time period. A further analysis of the CHIMERE model results revealed the need of improving the parametrization of the in-cloud scavenging and vertical diffusivity schemes; such modifications are relevant especially when the model is applied under mist, fog and low stratus conditions, which frequently occur in the Po valley during winter. The sensitivity of modeled particulate matter concentrations to turbulence parameters, wind, temperature and cloud liquid water content in one of the most polluted and complex areas in Europe is finally discussed.

The extraction of liquid, protein molecules and yeast cells from paper through surface acoustic wave atomization.

PubMed

Qi, Aisha; Yeo, Leslie; Friend, James; Ho, Jenny

2010-02-21

Paper has been proposed as an inexpensive and versatile carrier for microfluidics devices with abilities well beyond simple capillary action for pregnancy tests and the like. Unlike standard microfluidics devices, extracting a fluid from the paper is a challenge and a drawback to its broader use. Here, we extract fluid from narrow paper strips using surface acoustic wave (SAW) irradiation that subsequently atomizes the extracted fluid into a monodisperse aerosol for use in mass spectroscopy, medical diagnostics, and drug delivery applications. Two protein molecules, ovalbumin and bovine serum albumin (BSA), have been preserved in paper and then extracted using atomized mist through SAW excitation; protein electrophoresis shows there is less than 1% degradation of either protein molecule in this process. Finally, a solution of live yeast cells was infused into paper, which was subsequently dried for preservation then remoistened to extract the cells via SAW atomization, yielding live cells at the completion of the process. The successful preservation and extraction of fluids, proteins and yeast cells significantly expands the usefulness of paper in microfluidics.

Electrospray Collection of Lunar Dust

NASA Technical Reports Server (NTRS)

Dziekan, Michael

2012-01-01

A report describes ElectroSpray Ionization based Electrostatic Precipitation (ESIEP) for collecting lunar dust particles. While some HEPA filtration processes may remove a higher fraction (>99.9 percent) of the particles, the high efficiency may not be appropriate from an overall system standpoint, especially in light of the relatively large power requirement that such systems demand. The new electrospray particle capture technology is described as a variant of electrostatic precipitation that eliminates the current drawbacks of electrostatic precipitation. The new approach replaces corona prone field with a mist of highly charged micro-droplets generated by electrospray ionization (ESI) as the mechanism by which incoming particles are attracted and captured. In electrospray, a miniscule flow rate (microliters/minute) of liquid (typically water and a small amount of salt to enhance conductivity) is fed from the tip of a needle held at a high voltage potential relative to an opposite counter electrode. At sufficient field strength, a sharp liquid meniscus forms , which emits a jet of highly charged droplets that drift through the surrounding gas and are collected on the walls of a conductive tube. Particles in the gas have a high probability of contact with the droplets either by adhering to the droplets or otherwise acquiring a high level of charge, causing them to be captured on the collecting electrode as well. The spray acts as a filtration material that is continuously introduced and removed from the gas flow, and thus can never become clogged.

Electrohydrodynamically driven large-area liquid ion sources

DOEpatents

Pregenzer, Arian L.

1988-01-01

A large-area liquid ion source comprises means for generating, over a large area of the surface of a liquid, an electric field of a strength sufficient to induce emission of ions from a large area of said liquid. Large areas in this context are those distinct from emitting areas in unidimensional emitters.

Associations between added sugar (solid vs. liquid) intakes, diet quality, and adiposity indicators in Canadian children.

PubMed

Wang, JiaWei; Shang, Lei; Light, Kelly; O'Loughlin, Jennifer; Paradis, Gilles; Gray-Donald, Katherine

2015-08-01

Little is known about the influence of different forms of added sugar intake on diet quality or their association with obesity among youth. Dietary intake was assessed by three 24-h recalls in 613 Canadian children (aged 8-10 years). Added sugars (mean of 3-day intakes) were categorized according to source (solid or liquid). Dietary intake and the Canadian Healthy Eating Index (« HEI-C ») were compared across tertiles of solid and liquid added sugars separately as were adiposity indicators (body mass index (BMI), fat mass (dual-energy X-ray absorptiometry), and waist circumference). Cross-sectional associations were examined in linear regression models adjusting for age, sex, energy intake, and physical activity (7-day accelerometer). Added sugar contributed 12% of total energy intake (204 kcal) on average, of which 78% was from solid sources. Higher consumption of added sugars from either solid or liquid source was associated with higher total energy, lower intake of micronutrients, vegetables and fruit, and lower HEI-C score. Additionally liquid sources were associated with lower intake of dairy products. A 10-g higher consumption of added sugars from liquid sources was associated with 0.4 serving/day lower of vegetables and fruit, 0.4-kg/m(2) higher BMI, a 0.5-kg higher fat mass, and a 0.9-cm higher waist circumference whereas the associations of added sugars from solid sources and adiposity indicators tended to be negative. In conclusion, higher consumption of added sugar from either solid or liquid sources was associated with lower overall diet quality. Adiposity indicators were only positively associated with added sugars from liquid sources.

Characteristics of sprinklers and water spray mists for fire safety

NASA Astrophysics Data System (ADS)

Jackman, Louise A.; Lavelle, Stephen P.; Nolan, P. F.

1991-04-01

In order to predict the type of sprinkler or spray head required for fire safety in buildings and transport systems (e.g. aircraft) it is necessary to model the interaction of water droplets with the thermally buoyant fire gases. Such modelling requires a detailed knowledge of the mean droplet size, the droplet size distribution, droplet velocity and trajectory. Many existing systems for the characterisation of droplets are indirect in that an optical property is measured and the results are subject to "black box" data processing. A direct method can be developed using a synchronised metal vapour laser and high speed cine camera with appropriate optics. Results on both sprinkler and spray mist will be presented and a basis for the choice of active fire protection systems will be outlined.

In-Situ Resource Utilization (ISRU) Development Program

NASA Technical Reports Server (NTRS)

Sanders, Jerry

1998-01-01

The question "Why In-Situ Resource Utilization (ISRU)?" is addressed in this presentation. The reasons given concentrate on Cost reduction, Mass reduction, Risk reduction, the expansion of human exploration and presence and the enabling of industrial exploitation. A review of the Martian and Lunar resources available for ISRU is presented. Other ISRU concepts (i.e., In-Situ Consumable production (ISCP) and In-Situ Propellant Production (ISPP)) are introduced and further explained. The objectives of a Mars ISRU System Technology (MIST) include (1) the characterization of technology and subsystem performance for mission modeling and technology funding planning, (2) reduce risk and concerns arising from sample return and human missions utilizing ISRU, and (3) demonstrate the environmental suitability of ISRU components/processes and systems. A proof of concept demonstration schedule and a facility overview for MIST is presented.

Operations FLINTLOCK and LATCHKEY events RED HOT, PIN STRIPE, DISCUS THROWER, PILE DRIVER, DOUBLE PLAY, NEWPOINT, MIDI MIST, 5 March 1966-26 Jun 1967. Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horton, K.K.; Eubank, B.F.; Brady, W.J.

1984-10-01

This report is a personnel-oriented history of DOD participation in underground nuclear weapons testing during Operations FLINTLOCK and LATCHKEY, test events RED HOT, PIN STRIPE, DISCUS THROWER, PILE DRIVER, DOUBLE PLAY, NEW POINT, and MIDI MIST, from 5 March 1966 to 26 June 1967. It is the second in a series of historical reports which will include all DOD underground nuclear weapons tests and all DOE underground nuclear weapons tests with significant DOD participation from 1962 forward. In addition to these historical volumes, a later restricted distribution volume will identify all DOD participants (military, civilian, and civilian contractors) and willmore » list their radiation dosimetry data.« less

Development of the International Space Station (ISS) Fine Water Mist (FWM) Portable Fire Extinguisher ICES Abstract

NASA Technical Reports Server (NTRS)

Clements, Anna L.; Carlile, Christie; Graf, John; Young, Gina

2011-01-01

NASA is developing a Fine Water Mist (FWM) Portable Fire Extinguisher (PFE) for use on the International Space Station. The International Space Station presently uses two different types of fire extinguishers: a water foam extinguisher in the Russian Segment, and a carbon dioxide extinguisher in the US Segment and Columbus and Kibo pressurized elements. Changes in emergency breathing equipment make Fine Water Mist operationally preferable. Supplied oxygen breathing systems allow for safe discharge of a carbon dioxide fire extinguisher, without concerns of the crew inhaling unsafe levels of carbon dioxide. But the Portable Breathing Apparatus (PBA) offers no more than 15 minutes of capability, and continued use of hose based supplied oxygen system increases the oxygen content in a fire situation. NASA has developed a filtering respirator cartridge for use in a fire environment. It is qualified to provide up to 90 minutes of capability, and because it is a filtering respirator it does not add oxygen to the environment. The fire response respirator cartridge does not filter carbon dioxide (CO2), so a crew member discharging a CO2 fire extinguisher while wearing this filtering respirator would be at risk of inhaling unsafe levels of CO2. FWM extinguishes a fire without creating a large volume of air with reduced oxygen and elevated CO2. The following paper will discuss the unique functional and performance requirements that have been levied on the FWM PFE. In addition, the NASA ISS specific fire standards will be described which were developed to establish acceptable extinguisher performance. The paper will also discuss the flight hardware design. The fin e water mist fire extinguisher has two major elements: (1) the nozzle and crew interface, and (2) the tank. The nozzle and crew interface have been under development for several years. They have gone through several design iterations, and have been part of more than 400 fire challenge and spray characterizations. The crew and vehicle interface aspects of the design will use the heritage of the CO2 based Portable Fire Extinguisher, to minimize the disruption to the crew and integration impacts to the ISS. The microgravity use environment of the system poses a set of unique design requirements specifically for the tank. The nozzle requirements drive a tank pressure that is 2-5 times higher than any commercially available water mist systems. Microgravity requires deliberate separation of gas and water, facilitated by a bladder, a diaphragm, a piston, or separate tanks. This paper will describe status of the project to date, the design details of the tank and the nozzle, and discuss the trade studies that informed the decisions to select the tank and nozzle configuration.

Croup (For Parents)

MedlinePlus

... mist will sometimes stop the severe coughing. In cooler weather, taking your child outside for a few ... hard to awaken is dehydrated (signs include a dry or sticky mouth, few or no tears when ...

SHEEN-MAGIC©

EPA Pesticide Factsheets

Technical product bulletin: recommended treatment with this surface washing agent, used in oil spill cleanups, is light misting of contaminated surface. Additional may be needed for heavier hydrocarbon sheens. Wave action and rainfall enhance performance

Self-sustained flow oscillations and heat transfer in radial flow through co-rotating parallel disks

NASA Astrophysics Data System (ADS)

Mochizuki, S.; Inoue, T.

1990-03-01

An experimental study was conducted to determine the fluid flow and heat transfer characteristics in a passage formed by two parallel rotating disks. The local heat transfer coefficients along the disk radius were measured in detail and the flow patterns between the two rotating disks were visualized by using paraffin mist and a laser-light sheet. It was disclosed that: (1) the self-sustained laminar flow separation which is characteristic of the stationary disks still exists even when the disks are set in motion, giving significant influence to the heat transfer; (2) for small source flow Reynolds number, Re, and large rotational Reynolds number, Re(omega), rotating stall dominates the heat transfer; and (3) heat transfer for steady laminar flow occurs only when Re is less than 1200 and Re(omega) is less than 20.

40 CFR 63.2480 - What requirements must I meet for equipment leaks?

Code of Federal Regulations, 2011 CFR

2011-07-01

... affected source. (5) For pumps in light liquid service in an MCPU that has no continuous process vents and.../vapor and light liquid service at an existing source, you may elect to comply with the requirements in... light liquid service in an MCPU that has no continuous process vents and is part of an existing source...

Using liquid waste streams as the moisture source during the hydrothermal carbonization of municipal solid wastes.

PubMed

Li, Liang; Hale, McKenzie; Olsen, Petra; Berge, Nicole D

2014-11-01

Hydrothermal carbonization (HTC) is a thermal conversion process that can be an environmentally beneficial approach for the conversion of municipal solid wastes to value-added products. The influence of using activated sludge and landfill leachate as initial moisture sources during the carbonization of paper, food waste and yard waste over time at 250°C was evaluated. Results from batch experiments indicate that the use of activated sludge and landfill leachate are acceptable alternative supplemental liquid sources, ultimately imparting minimal impact on carbonization product characteristics and yields. Regression results indicate that the initial carbon content of the feedstock is more influential than any of the characteristics of the initial liquid source and is statistically significant when describing the relationship associated with all evaluated carbonization products. Initial liquid-phase characteristics are only statistically significant when describing the solids energy content and the mass of carbon in the gas-phase. The use of these alternative liquid sources has the potential to greatly increase the sustainability of the carbonization process. A life cycle assessment is required to quantify the benefits associated with using these alternative liquid sources. Copyright © 2014 Elsevier Ltd. All rights reserved.

Rapid Identification of a Cooling Tower-Associated Legionnaires' Disease Outbreak Supported by Polymerase Chain Reaction Testing of Environmental Samples, New York City, 2014-2015.

PubMed

Benowitz, Isaac; Fitzhenry, Robert; Boyd, Christopher; Dickinson, Michelle; Levy, Michael; Lin, Ying; Nazarian, Elizabeth; Ostrowsky, Belinda; Passaretti, Teresa; Rakeman, Jennifer; Saylors, Amy; Shamoonian, Elena; Smith, Terry-Ann; Balter, Sharon

2018-04-01

We investigated an outbreak of eight Legionnaires' disease cases among persons living in an urban residential community of 60,000 people. Possible environmental sources included two active cooling towers (air-conditioning units for large buildings) <1 km from patient residences, a market misting system, a community-wide water system used for heating and cooling, and potable water. To support a timely public health response, we used real-time polymerase chain reaction (PCR) to identify Legionella DNA in environmental samples within hours of specimen collection. We detected L. pneumophila serogroup 1 DNA only at a power plant cooling tower, supporting the decision to order remediation before culture results were available. An isolate from a power plant cooling tower sample was indistinguishable from a patient isolate by pulsed-field gel electrophoresis, suggesting the cooling tower was the outbreak source. PCR results were available <1 day after sample collection, and culture results were available as early as 5 days after plating. PCR is a valuable tool for identifying Legionella DNA in environmental samples in outbreak settings.

Trace organic compounds in wet atmospheric deposition: an overview

USGS Publications Warehouse

Steinheimer, T.R.; Johnson, S.M.

1987-01-01

An overview of the occurrence of organic compounds in wet atmospheric deposition is given. Multiplicity of sources and problems associated with source identification are discussed. Available literature is reviewed by using citations from Chemical Abstracts and Water Resources Abstracts through June 1985 and includes reports published through December 1984 that summarize current knowledge. Approaches to the chemical determination of organic compounds in precipitation are examined in addition to aspects of sampling protocols. Best methods for sample collection and preparation for instrumental analysis continue to be discussed among various investigators. Automatic wet-deposition-only devices for collection and extraction are preferred. Classes of organic compounds that have been identified in precipitation include a spectrum of compounds with differing properties of acidity or basicity, polarity, and water solubility. Those compounds that have been reported in rainfall, snowfall, and ice include hydrocarbons (both aromatic and nonaromatic), chlorinated derivatives of these hydrocarbons, carbonyl compounds (both acidic and nonacidic), and carboxylic acids and esters. Formic and acetic are the most abundant organic acids present. Cloudwater, fogwater, and mist also have been collected and analyzed for organic composition.

Legionnaires' Disease

MedlinePlus

Legionnaires' disease is a type of pneumonia caused by bacteria. You usually get it by breathing in mist from ... spread from person to person. Symptoms of Legionnaires' disease include high fever, chills, a cough, and sometimes ...

Protect Yourself: Respirators

MedlinePlus

... dust masks) can be used for dust, mists, welding fumes, etc. They do not provide protection from ... tion against most vapors, acid gases, dust or welding fumes. Cartridges/filters must match contaminant(s) and be ...

Vapor/Mist Used to Lubricate Gears After Loss of Primary Lubrication System

NASA Technical Reports Server (NTRS)

Handschuh, Robert F.; Morales, Wilfredo

2001-01-01

Loss of lubrication in rotorcraft drive systems is a demanding requirement placed on drive system manufacturers. The drive system must operate for at least 30 minutes once the primary lubrication system has failed. This test is a military requirement that must be passed prior to certification of the aircraft. As new aircraft engines, operating at higher speeds, are fielded, the requirements for the drive system become increasingly more difficult. Also, the drive system must be lightweight, which minimizes the opportunity to use the gear bodies to absorb the tremendous amount of heating that takes place. In many cases, the amount of heat generated because of the high speed and load requires an emergency lubrication system that negatively impacts the aircraft's weight, complexity, and cost. A single mesh spur gear test rig is being used at the NASA Glenn Research Center to investigate possible emergency lubrication system improvements that will minimize the impact of having these systems onboard rotorcraft. A technique currently being investigated uses a vapor/mist system to lubricate the contacting surfaces after the primary lubrication system has been shut down. A number of tests were conducted in which the vapor/mist used the same lubricant as the primary system, but at a greatly reduced flow rate. Each test was initiated with the primary lubrication system operational and at steady-state conditions for a given speed and load. Then the primary lubrication system was shut down, and the vapor/mist lubrication system was initiated. An example of the tests conducted is shown in the figures. These preliminary tests have uncovered a mechanism that provides a lubricious, carbonaceous solid on the surface that actually reduces the surface temperature of the meshing gear teeth during operation. Surface analysis of the carbonaceous solid revealed it was graphitic. This mechanism is the synthetic lubricant "coking" on the active profile of the gears, which reduces the friction between the contacting gear surfaces. The level of load affects the onset of this mechanism: the higher the load, the sooner coking takes place. Future work will investigate several other factors that could improve the already promising results that have been attained.

Material Ignition and Suppression Test (MIST) in Space Exploration Atmospheres, Summary of Research

NASA Technical Reports Server (NTRS)

Fernandez-Pello, Carlos

2013-01-01

The Material Ignition and Suppression Test (MIST) project has had the objective of evaluating the ease of ignition and the fire suppression of materials used in spacecraft under environmental condition expected in a spacecraft. For this purpose, an experimental and theoretical research program is being conducted on the effect of space exploration atmospheres (SEA) on the piloted ignition of representative combustible materials, and on their fire suppression characteristics. The experimental apparatus and test methodology is derived from the Forced Ignition and Flame Spread Test (FIST), a well-developed bench scale test designed to extract material properties relevant to prediction of material flammability. In the FIST test, materials are exposed to an external radiant flux and the ignition delay and critical mass flux at ignition are determined as a function of the type of material and environmental conditions. In the original MIST design, a small-scale cylindrical flow duct with fuel samples attached to its inside wall was heated by a cylindrical heater located at the central axis of the cylinder. However, as the project evolved it was decided by NASA that it would be better to produce an experimental design that could accommodate other experiments with different experimental concepts. Based on those instructions and input from the requirements of other researchers that may share the hardware in an ISS/CIR experiment, a cylindrical design based on placing the sample at the center of an optically transparent tube with heaters equally spaced along the exterior of the cylinder was developed. Piloted ignition is attained by a hot wire igniter downstream of the fuel sample. Environment variables that can be studied via this experimental apparatus include: external radiant flux, oxidizer oxygen concentration, flow velocity, ambient pressure, and gravity level (if flown in the ISS/CIR). This constitutes the current experimental design, which maintains fairly good consistency with Dr Tien's and Dr Olson's project approaches. A further goal of the project has been to develop a combined solid/gas phase numerical model based on the MIST test methodology to predict the flammability behavior of practical materials in spacecraft.

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

NASA Astrophysics Data System (ADS)

Boyle, Dennis Patrick

This thesis presents new measurements of core impurity concentrations and transport in plasmas with lithium coatings on all-metal plasma facing components (PFCs) in the Lithium Tokamak Experiment (LTX). LTX is a modest-sized spherical tokamak uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma (as opposed to just the divertor or limiter region in other devices). Lithium (Li) wall-coatings have improved plasma performance and confinement in several tokamaks with carbon (C) PFCs, including the National Spherical Torus Experiment (NSTX). In NSTX, contamination of the core plasma with Li impurities was very low (<0.1%) despite extensive divertor coatings. Low Li levels in NSTX were found to be largely due to neoclassical forces from the high level of C impurities. Studying impurity levels and transport with Li coatings on stainless steel surfaces in LTX is relevant to future devices (including future enhancements to NSTX-Upgrade) with all-metal PFCs. The new measurements in this thesis were enabled by a refurbished Thomson scattering system and improved impurity spectroscopy, primarily using a novel visible spectrometer monitoring several Li, C, and oxygen (O) emission lines. A simple model was used to account for impurities in unmeasured charge states, assuming constant density in the plasma core and constant concentration in the edge. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with 2-4% Li, 0.6-2% C, 0.4-0.7% O, and Z eff<1.2. Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, unlike in NSTX, where collisions with C dominated. Furthermore, neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two, in contrast to NSTX where they differed by an order of magnitude. However, time-independent simulations with MIST indicated that unlike NSTX, neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles.

Measurements of impurity concentrations and transport in the Lithium Tokamak Experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyle, Dennis Patrick

This thesis presents new measurements of core impurity concentrations and transport in plasmas with lithium coatings on all-metal plasma facing components (PFCs) in the Lithium Tokamak Experiment (LTX). LTX is a modest-sized spherical tokamak uniquely capable of operating with large area solid and/or liquid lithium coatings essentially surrounding the entire plasma (as opposed to just the divertor or limiter region in other devices). Lithium (Li) wall-coatings have improved plasma performance and confinement in several tokamaks with carbon (C) PFCs, including the National Spherical Torus Experiment (NSTX). In NSTX, contamination of the core plasma with Li impurities was very low (<0.1%)more » despite extensive divertor coatings. Low Li levels in NSTX were found to be largely due to neoclassical forces from the high level of C impurities. Studying impurity levels and transport with Li coatings on stainless steel surfaces in LTX is relevant to future devices (including future enhancements to NSTX-Upgrade) with all-metal PFCs. The new measurements in this thesis were enabled by a refurbished Thomson scattering system and improved impurity spectroscopy, primarily using a novel visible spectrometer monitoring several Li, C, and oxygen (O) emission lines. A simple model was used to account for impurities in unmeasured charge states, assuming constant density in the plasma core and constant concentration in the edge. In discharges with solid Li coatings, volume averaged impurity concentrations were low but non-negligible, with~2-4% Li, ~0.6-2% C, ~0.4-0.7% O, and Z_eff<1.2. Transport was assessed using the TRANSP, NCLASS, and MIST codes. Collisions with the main H ions dominated the neoclassical impurity transport, unlike in NSTX, where collisions with C dominated. Furthermore, neoclassical transport coefficients calculated with NCLASS were similar across all impurity species and differed no more than a factor of two, in contrast to NSTX where they differed by an order of magnitude. However, time-independent simulations with MIST indicated that unlike NSTX, neoclassical theory did not fully capture the impurity transport and anomalous transport likely played a significant role in determining impurity profiles.« less

Health effects of oil mists: a brief review.

PubMed

Mackerer, C R

1989-05-01

Metal cutting/grinding fluids are of three basic types: straight oil (insoluble), oil-in-water emulsions (soluble) and synthetic/semisynthetic. All contain a variety of additives to improve performance. Human exposure occurs primarily by direct skin contact with the liquid or by skin and respiratory contact after fluid misting. Dermatitis caused by primary or direct skin irritation is the most prevalent health effect of exposure to cutting fluids. Occasionally allergic dermatitis is seen which is related to the development of sensitization to one or more of the additive components. Recent studies indicate that long-term exposure to cutting fluids does not result in increased incidences of lung cancer, urinary bladder cancer, gastrointestinal cancer, or death from non-malignant respiratory diseases. Long-term exposure to certain cutting fluids, however, is believed to have resulted in certain types of skin cancer, especially scrotal cancer. It is likely that these carcinogenic responses were caused by contact with polycyclic aromatic compounds (PCA) of 3-7 rings. Modern base oils which are severely refined have very low levels of PCA, are not carcinogenic in animal bioassays, and are unlikely to be carcinogenic in man. This is not necessarily true for re-refined oils which may contain significant levels of PCA and polychlorinated biphenyls derived from comingling used cutting oils with used engine oils and transformer oils. Cutting oils, themselves, generally do not accumulate significant levels of carcinogenic PCA during use. Additives, in theory, can cause a variety of health effects either directly or through the generation of reaction products such as nitrosamines. In actual use, adverse health effects appear to be limited to occasional instances of allergic contact dermatitis. Nitrosamines are extremely carcinogenic in test animals; although no human cancer cases directly attributable to nitrosamine contamination have been observed, nitrosating agents and amines should not be combined in cutting fluid formulations. It is difficult to anticipate or predict the potential toxicity of a particular cutting fluid formulation because of the presence of variable amounts of proprietary additives which, themselves, are often complex reaction mixtures. Thus, each additive and final formulation must be evaluated on a case by case basis to appropriately assess potential health hazards.

Bright Lights, Green City

NASA Image and Video Library

2010-07-28

Two extremely bright stars illuminate a greenish mist in this image from the new GLIMPSE360 survey from NASA Spitzer Space Telescope. The fog is comprised of hydrogen and carbon compounds called polycyclic aromatic hydrocarbons.

40 CFR 62.7375 - Identification of plan-negative declaration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS New Hampshire Sulfuric Acid Mist Emissions from Sulfuric Acid Production Units § 62.7375 Identification of plan...

40 CFR 62.7375 - Identification of plan-negative declaration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS New Hampshire Sulfuric Acid Mist Emissions from Sulfuric Acid Production Units § 62.7375 Identification of plan...

40 CFR 62.7375 - Identification of plan-negative declaration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS New Hampshire Sulfuric Acid Mist Emissions from Sulfuric Acid Production Units § 62.7375 Identification of plan...

40 CFR 62.7375 - Identification of plan-negative declaration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS New Hampshire Sulfuric Acid Mist Emissions from Sulfuric Acid Production Units § 62.7375 Identification of plan...

40 CFR 62.7375 - Identification of plan-negative declaration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF STATE PLANS FOR DESIGNATED FACILITIES AND POLLUTANTS New Hampshire Sulfuric Acid Mist Emissions from Sulfuric Acid Production Units § 62.7375 Identification of plan...

Ventilation Guidance for Spray Polyurethane Foam Application

EPA Pesticide Factsheets

Properly designed ventilation can reduce airborne levels of aerosols, mists, and vapors generated during spray application and can help protect SPF applicators, helpers, and others who may be working in adjacent areas.

A liquid hydrocarbon deuteron source for neutron generators

NASA Astrophysics Data System (ADS)

Schwoebel, P. R.

2017-06-01

Experimental studies of a deuteron spark source for neutron generators using hydrogen isotope fusion reactions are reported. The ion source uses a spark discharge between electrodes coated with a deuterated hydrocarbon liquid, here Santovac 5, to inhibit permanent electrode erosion and extend the lifetime of high-output neutron generator spark ion sources. Thompson parabola mass spectra show that principally hydrogen and deuterium ions are extracted from the ion source. Hydrogen is the chief residual gas phase species produced due to source operation in a stainless-steel vacuum chamber. The prominent features of the optical emission spectra of the discharge are C+ lines, the hydrogen Balmer Hα-line, and the C2 Swan bands. Operation of the ion source was studied in a conventional laboratory neutron generator. The source delivered an average deuteron current of ˜0.5 A nominal to the target in a 5 μs duration pulse at 1 Hz with target voltages of -80 to -100 kV. The thickness of the hydrocarbon liquid in the spark gap and the consistency thereof from spark to spark influences the deuteron yield and plays a role in determining the beam-focusing characteristics through the applied voltage necessary to break down the spark gap. Higher breakdown voltages result in larger ion beam spots on the target and vice-versa. Because the liquid self-heals and thereby inhibits permanent electrode erosion, the liquid-based source provides long life, with 104 pulses to date, and without clear evidence that, in principle, the lifetime could not be much longer. Initial experiments suggest that an alternative cylindrical target-type generator design can extract approximately 10 times the deuteron current from the source. Preliminary data using the deuterated source liquid as a neutron-producing target are also presented.

30 CFR 56.5002 - Exposure monitoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

... SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Air Quality and Physical Agents Air Quality § 56.5002 Exposure monitoring. Dust, gas, mist, and fume surveys shall be conducted as...

41 CFR 50-204.69 - Nitrous oxide.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Vapors, Fumes, Dusts, and Mists § 50-204.69 Nitrous oxide. The piped systems for the in-plant transfer and distribution of nitrous oxide shall be designed, installed, maintained, and operated in accordance...

78 FR 20352 - Endangered and Threatened Species Permit Applications

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-04

... Applicant: Burns and McDonnell Engineering, Kansas City, Missouri. Applicant requests an amendment to a..., identify, and release using mist nets and harp traps; collect tissue samples using wing punches, hair...

COPD -- how to use a nebulizer

MedlinePlus

... this page: //medlineplus.gov/ency/patientinstructions/000699.htm COPD - how to use a nebulizer To use the ... page, please enable JavaScript. A nebulizer turns your COPD medicine into a mist. It is easier to ...

MARINE D-BLUE CLEAN™

EPA Pesticide Factsheets

Technical product bulletin: this dispersant is used in oil spill cleanups on salt water, sprayed onto slick in atomized form using moderately coarse droplets rather than fine mist. Effective with crude and residual heavy oil spills.

75 FR 20546 - Total Inward Leakage Requirements for Respirators

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-20

... respiratory protection to intended users against toxic dusts, mists, fumes, fibers, and biological and infectious aerosols (e.g., influenza A (H5N1), Bacillus anthracis, severe acute respiratory syndrome (SARS...

40 CFR 62.5100 - Identification of plan.

Code of Federal Regulations, 2011 CFR

2011-07-01

... acid mist from sulfuric acid plants, submitted by the Secretary of Health and Mental Hygiene, State of..., submitted by the Secretary of Health and Mental Hygiene, State of Maryland on January 26, 1984. (c...

Your Nose, the Guardian of Your Lungs

MedlinePlus

... will be impaired. Try over-the-counter salt-water (saline) nasal mists and sprays to help maintain ... frequently during the flight, and drink lots of water. Medications Prescribed To Treat Nasal Problems: Be aware ...

Characterization and degradation studies on synthetic polymers for aerospace application

NASA Technical Reports Server (NTRS)

Hsu, M. T. S.

1982-01-01

The anti-misting additive for jet fuels known as FM-9 (proprietary polymer) was characterized by elemental analysis, solubility studies and molecular weight determination. Physical properties of surface tension, viscosity, specific gravity and other physical parameters were determined. These results are compared with properties of polyisobutylene and fuels modified with the same; the misting characteristics of polyisobutylene and FM-9 in Jet A fuel are included. Characterization and degradation of phthalocyanine and its derivatives were accomplished by use of a mass spectrometer and a pyroprobe solid pyrolyzer. Metal phthalocyanine tetracarboxylic acids and phthalocyanine-tetraamine cured epoxies were studied. Epoxy/graphite composite panels were exposed to a NASA-Ames radiant panel fire simulator in the flaming and non-flaming modes; toxic gases of HCN and HZS were measured along with oxygen, Co2, Co, and organic gases.

Surgical novices randomized to train in two video games become more motivated during training in MIST-VR and GI Mentor II than students with no video game training.

PubMed

Hedman, Leif; Schlickum, Marcus; Felländer-Tsai, Li

2013-01-01

We investigated if engagement modes and perceived self-efficacy differed in surgical novices before and after randomized training in two different video games during five weeks, and a control group with no training. The control group expressed to a higher extent negative engagement modes during training in MIST-VR and GI Mentor II than the experimental groups. No statistically significant differences in self-efficacy were identified between groups. Both engagement modes and self-efficacy showed a positive correlation with previous and present video game experience. It is suggested that videogame training could have a framing effect on surgical simulator performance. EM and SE might be important intermediate variables between the strength of relationship between current videogame experience and simulator performance.

STS-107 Flight Day 12 Highlights

NASA Technical Reports Server (NTRS)

2003-01-01

This video shows the activities of the STS-107 crew (Rick Husband, Commander; William McCool, Pilot; Kalpana Chawla, David Brown, Michael Anderson, Laurel Clark, Mission Specialists; Ilan Ramon, Payload Specialist) during flight day 12 of the Columbia orbiter's final mission. The primary activities are spaceborne experiments in the SpaceHab RDM (Research Double Module). Experiments shown in the video include SOFBALL (Structure of Flame Balls at Low Lewis-Number), an experiment to grow cancer cells in microgravity, and the STARS (Space Technology and Research Students) experiments, including bees, ants, chemical gardens, fish, and spiders. Crew Members are shown working on MIST (Water Mist Fire Suppression), a commercial experiment. Red Team crew members (Husband, Chawla, Clark, Ramon) are shown conversing through a handset with the Expedition 6 crew (Kenneth Bowersox, Commander; Donald Pettit, Nikolai Budarin; Flight Engineers) of the ISS (International Space Station).

Emergency and microfog lubrication and cooling of bearings for Army helicopters

NASA Technical Reports Server (NTRS)

Rosenlieb, J. W.

1978-01-01

An analysis and system study was performed to provide design information regarding lubricant and coolant flow rates and flow paths for effective utilization of the lubricant and coolant in a once-through oil-mist (microfog) and coolant air system. A system was designed, manufactured, coupled with an existing rig and evaluation tests were performed using 46 mm bore split-inner angular-contact ball bearings under 1779N (400 lb.) thrust load. An emergency lubrication aspirator system was also manufactured and tested under lost lubricant conditions. The testing demonstrated the feasibility of using a mist oil and cooling air system to lubricate and cool a high speed helicopter engine mainshaft bearing. The testing also demonstrated the feasibility of using an emergency aspirator lubrication system as a viable survivability concept for helicopter mainshaft engine bearing for periods as long as 30 minutes.

KSC-2014-4322

NASA Image and Video Library

2014-07-24

CAPE CANAVERAL, Fla. – Inside the Prototype Laboratory at NASA's Kennedy Space Center in Florida, Evan Williams, left, an Education intern from the University of Central Florida, and Anthony Bharrat, NASA avionics lead, prepare the experiment container for NASA's Exposing Microorganisms in the Stratosphere, or E-MIST, experiment. The container was designed and built at Kennedy. The 80-pound structure features four doors that rotate to expose up to 10 microbial samples each for a predetermined period of time in the Earth's stratosphere. The E-MIST experiment will launch on the exterior of a giant scientific balloon gondola at about 8 a.m. MST on Aug. 24 from Ft. Sumner, New Mexico. It will soar 125,000 feet above the Earth during a 5-hour journey over the desert to understand how spore-forming bacteria, commonly found in spacecraft assembly facilities can survive. Photo credit: NASA/Kim Shiflett

KSC-2014-4323

NASA Image and Video Library

2014-07-24

CAPE CANAVERAL, Fla. – Inside the Prototype Laboratory at NASA's Kennedy Space Center in Florida, Evan Williams, an Education intern from the University of Central Florida, prepares the experiment container for NASA's Exposing Microorganisms in the Stratosphere, or E-MIST, experiment. The container was designed and built at Kennedy. The 80-pound structure features four doors that rotate to expose up to 10 microbial samples each for a predetermined period of time in the Earth's stratosphere. The E-MIST experiment will launch on the exterior of a giant scientific balloon gondola at about 8 a.m. MST on Aug. 24 from Ft. Sumner, New Mexico. It will soar 125,000 feet above the Earth during a 5-hour journey over the desert to understand how spore-forming bacteria, commonly found in spacecraft assembly facilities can survive. Photo credit: NASA/Kim Shiflett

Structural characteristics of a non-polar ZnS layer on a ZnO buffer layer formed on a sapphire substrate by mist chemical vapor deposition

NASA Astrophysics Data System (ADS)

Okita, Koshi; Inaba, Katsuhiko; Yatabe, Zenji; Nakamura, Yusui

2018-06-01

ZnS is attractive as a material for low-cost light-emitting diodes. In this study, a non-polar ZnS layer was epitaxially grown on a sapphire substrate by inserting a ZnO buffer layer between ZnS and sapphire. The ZnS and ZnO layers were grown by a mist chemical vapor deposition system with a simple setup operated under atmospheric pressure. The sample was characterized by high-resolution X-ray diffraction measurements including 2θ/ω scans, rocking curves, and reciprocal space mapping. The results showed that an m-plane wurtzite ZnS layer grew epitaxially on an m-plane wurtzite ZnO buffer layer formed on the m-plane sapphire substrate to provide a ZnS/ZnO/sapphire structure.

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...

40 CFR 98.400 - Definition of the source category.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Suppliers of Natural Gas and Natural Gas Liquids § 98.400 Definition of the source category. This supplier category consists of natural gas liquids fractionators and local natural gas distribution companies. (a) Natural gas liquids fractionators are installations that...