High performance Li2MnO3/rGO composite cathode for lithium ion batteries

NASA Astrophysics Data System (ADS)

Zhao, Wei; Xiong, Lilong; Xu, Youlong; Li, Houli; Ren, Zaihuang

2017-05-01

The novel composite Li2MnO3 (LMO)/reduced graphene oxide (rGO) has been synthesized successfully. Based on the scanning electron microscopy and transmission electron microscopy, LMO is found to distribute separately on the rGO sheets by forming a laminated structure, which is in favor of good electrical contact between the cathode active materials and the rGO matrix, and also facilitates the separation of LMO secondary particles with reduced size. Cyclic voltammetry and electrochemical impedance spectroscopy tests show that the charge transfer resistance decreases from 81.2 Ω for LMO to 29.6 Ω for LMO/rGO composite. The Li-ion diffusion coefficient of LMO/rGO composite is almost triple that of LMO. As a result, the LMO/rGO composite delivers an initial discharge capacity of 284.9 mAh g-1 with a capacity retention of 86.6% after 45 cycles at 0.1 C between 2.0 and 4.6 V. Cycle performance is even better at a higher current density 0.2 C while the retention ratio is up to 97.1% after 45 cycles. The rate capability is also significantly enhanced, and the LMO/rGO composite could exhibit a large discharge capacity of 123.7 mAh g-1 which is more than three times larger than that of LMO (40.8 mAh g-1) at a high rate of 8 C.

Surface studies of Li-ion and Mg battery electrodes

NASA Astrophysics Data System (ADS)

Esbenshade, Jennifer

This dissertation focuses on studies of the surfaces of both Li-ion and Mg-ion battery electrodes. A fundamental understanding of processes occurring at the electrode surface is vital to the development of advanced battery systems. Additionally, modifications to the electrode surfaces are made and further characterized for improved performance. LiMn2O4 Cathodes for Li-ion Batteries: Effect of Mn in electrolyte on anode and Au coating to minimize dissolution: LiMn2O4 (LMO) is known to dissolve Mn ions with cycling. This section focuses on both the effect of the dissolution of Mn2+ into the electrolyte as well as Au coating on the LMO to improve electrochemical performance. Electrochemical quartz crystal microbalance (EQCM) was used to monitor changes in mass on the anode, SEM and AES were used to observe changes in surface morphology and chemical composition, and potentiostatic voltammetry was used to monitor charge and discharge capacity. The effect of Cu2+ addition in place of Mn2+ was also studied, as Cu is known to form an underpotential deposition (UPD) monolayer on Au electrodes. Following this, LMO particles were coated with a Au shell by a simple and scalable electroless deposition for use as Li-ion battery cathodes. The Au shell was intended to limit the capacity fade commonly seen with LMO cathodes by reducing the dissolution of Mn. Characterization by SEM, TEM, EELS, and AFM showed that the Au shell was approximately 3 nm thick. The Au shell prevented much of the Mn from dissolving in the electrolyte with 82% and 88% less dissolved Mn in the electrolyte at room temperature and 65 ºC, respectively, as compared to the uncoated LMO. Electrochemical performance studies with half cells showed that the Au shell maintained a higher discharge capacity over 400 cycles by nearly 30% with 110 mA hr g-1 for the 400th cycle as compared to a commercial LMO at 85 mA hr g-1. Similarly, the capacity fade was reduced in full cells: the coated LMO had 47% greater capacity after 400 cycles over the control. Dimensionally Controlled Lithiation of Thin Film and Multilayer Conversion Li-ion Battery Anodes: Oxide conversion reactions are an alternative approach for high capacity Li-ion batteries, but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. The morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. In this section, a model electrode is used with alternating layers of Cr and CrOx to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials. Following the Cr/CrOx study, the next step was to study intermetallics which can electrochemically alloy to Li4.4M (M = Si, Ge, Sn, etc.), providing order-of-magnitude increases in energy density. The energy density of Si may be combined with the structural reversibility of an intercalation material using a Si/metal silicide multilayer (ML). In operando XR confirms the ML's structural reversibility during Li insertion and extraction, despite an overall 3.3-fold vertical expansion. The ML electrodes also show enhanced long-term cyclability and rate capabilities relative to a comparable Si thin film electrode. This intercalation behavior found by dimensionally constraining Si lithiation promises applicability to a range of conversion reactions. Improving Electrodeposition of Mg through an Open Circuit Potential Hold: In this section, in situ XRD, XPS, SEM and electrochemical methods were used to interrogate the mechanism of Mg electrodeposition from PhMgCl/AlCl3 (APC) and EtMgCl electrolytes. An open circuit potential (OCP) pause following Mg deposition led to retained enhancement of Mg deposition and stripping kinetics along with lowered overpotentials for both. In situ XRD demonstrated that the OCP pause led to a more polycrystalline deposits relative to that without the pause, while SEM presented micrographs that showed smaller deposits with an OCP hold. The improvement is attributed to an 'enhancement layer' that formed on the electrode during the OCP hold. Analysis of XPS data suggests that this 'enhancement layer' consists of Mg and Cl retained on the electrode surface, possibly following electrode depassivation.

Lunar Magma Ocean Bedrock Anorthosites Detected at Orientale Basin by M3

NASA Astrophysics Data System (ADS)

Pieters, C. M.; Boardman, J. W.; Burratti, B.; Cheek, L.; Clark, R. N.; Combe, J.; Green, R. O.; Head, J. W.; Hicks, M.; Isaacson, P.; Klima, R.; Kramer, G. Y.; Lundeen, S.; Malaret, E.; McCord, T. B.; Mustard, J. F.; Nettles, J. W.; Petro, N. E.; Runyon, C. J.; Staid, M.; Sunshine, J. M.; Taylor, L. A.; Tompkins, S.; Varanasi, P.

2009-12-01

The lunar crust is thought to have formed as a result of global melting of the outer parts of the Moon in its earliest history, a lunar magma ocean (LMO). Crystallization of this magma ocean set the stage for the ensuing history of the planet. Models for the formation of the lunar crust and the evolution of the LMO were derived from individual Apollo samples that could not be placed directly in the context of crustal bedrock with remote sensing data that was available. Data from modern sensors, such as the Moon Mineralogy Mapper (M3) on Chandrayaan-1, now allow such bedrock issues to be addressed. The ~930 km diameter Orientale multi-ringed impact basin in the western highlands provides an opportunity to evaluate the mineralogy of the in situ crust of the Moon in the search for LMO mineralogy and structure. Orientale is the youngest large basin on the Moon, and the basin deposits and ring structures expose progressively deeper bedrock layering that can be used to determine lunar crustal structure and test the LMO model. With its high spatial and spectral resolution, M3 data show that the ejecta of the basin is composed of mixed assemblages of processed feldspathic breccias with small amounts of low-Ca pyroxene comprising the upper kilometers-thick mega-regolith layer of the crust. Exposures in the outermost (Cordillera) ring reveal less processed examples of this material. The M3 data show that the next interior ring (Outer Rook), representing deeper material, is characterized by distinctly more crystalline blocks of impact-shocked anorthosite and noritic anorthosite. Most importantly, M3 data reveal that the mountains of the closest ring toward the basin interior (Inner Rook) consist of pure anorthosite, including outcrops of the unshocked crystalline form. This massive exposure of anorthosite across the entire mountain range provides validation for the LMO hypothesis. These mountains are believed to have originated in the upper crust below the impact fragmented regolith and were formed and uplifted during the basin event. Such extensive exposures of this rock type, consisting of almost pure plagioclase, could not have formed in any other way than plagioclase flotation in the crystallizing lunar magma ocean. Figure 1. Schematic cross section of the Orientale basin illustrating the relation of the Inner Rook Ring to the basin deposits of the exterior (after Head et al., 1993, JGR, 98, 17149).

Genes involved in Listeria monocytogenes biofilm formation at a simulated food processing plant temperature of 15 °C.

PubMed

Piercey, Marta J; Hingston, Patricia A; Truelstrup Hansen, Lisbeth

2016-04-16

Listeria monocytogenes is a pathogenic foodborne bacterium whose persistence in food processing environments is in part attributed to its biofilm formation. Most biofilm studies have been carried out at 30-37 °C rather than at temperatures found in the food processing plants (i.e., 10-20 °C). The objective of the present study was to mine for novel genes that contribute to L. monocytogenes biofilm formation at 15 °C using the random insertional mutagenesis approach. A library of 11,024 L. monocytogenes 568 (serotype 1/2a) Himar1 insertional mutants was created. Mutants with reduced or enhanced biofilm formation at 15 °C were detected in microtiter plate assays with crystal violet and safranin staining. Fourteen mutants expressed enhanced biofilm phenotypes, and harbored transposon insertions in genes encoding cell wall biosynthesis, motility, metabolism, stress response, and cell surface associated proteins. Deficient mutants (n=5) contained interruptions in genes related to peptidoglycan, teichoic acid, or lipoproteins. Enhanced mutants produced significantly (p<0.05) higher cell densities in biofilm formed on stainless steel (SS) coupons at 15 °C (48 h) than deficient mutants, which were also more sensitive to benzalkonium chloride. All biofilm deficient mutants and four enhanced mutants in the microtiter plate assay (flaA, cheR, lmo2563 and lmo2488) formed no biofilm in a peg lid assay (Calgary biofilm device) while insertions in lmo1224 and lmo0543 led to excess biofilm in all assays. Two enhanced biofilm formers were more resistant to enzymatic removal with DNase, proteinase K or pectinase than the parent strain. Scanning electron microscopy of individual biofilms made by five mutants and the parent on SS surfaces showed formation of heterogeneous biofilm with dense zones by immotile mutants, while deficient mutants exhibited sparse growth. In conclusion, interruptions of 9 genes not previously linked to biofilm formation in L. monocytogenes (lmo2572, lmo2488 (uvrA), lmo1224, lmo0434 (inlB), lmo0263 (inlH), lmo0543, lmo0057 (EsaA), lmo2563, lmo0453), caused enhanced biofilm formation in the bacterium at 15 °C. The remaining mutants harbored interruptions in 10 genetic loci previously associated with biofilm formation at higher temperatures, indicating some temperature driven differences in the formation of biofilm by L. monocytogenes. Copyright © 2016 Elsevier B.V. All rights reserved.

A Listeria monocytogenes RNA helicase essential for growth and ribosomal maturation at low temperatures uses its C terminus for appropriate interaction with the ribosome.

PubMed

Netterling, Sakura; Vaitkevicius, Karolis; Nord, Stefan; Johansson, Jörgen

2012-08-01

Listeria monocytogenes, a Gram-positive food-borne human pathogen, is able to grow at temperatures close to 0°C and is thus of great concern for the food industry. In this work, we investigated the physiological role of one DExD-box RNA helicase in Listeria monocytogenes. The RNA helicase Lmo1722 was required for optimal growth at low temperatures, whereas it was dispensable at 37°C. A Δlmo1722 strain was less motile due to downregulation of the major subunit of the flagellum, FlaA, caused by decreased flaA expression. By ribosomal fractionation experiments, it was observed that Lmo1722 was mainly associated with the 50S subunit of the ribosome. Absence of Lmo1722 decreased the fraction of 50S ribosomal subunits and mature 70S ribosomes and affected the processing of the 23S precursor rRNA. The ribosomal profile could be restored to wild-type levels in a Δlmo1722 strain expressing Lmo1722. Interestingly, the C-terminal part of Lmo1722 was redundant for low-temperature growth, motility, 23S rRNA processing, and appropriate ribosomal maturation. However, Lmo1722 lacking the C terminus showed a reduced affinity for the 50S and 70S fractions, suggesting that the C terminus is important for proper guidance of Lmo1722 to the 50S subunit. Taken together, our results show that the Listeria RNA helicase Lmo1722 is essential for growth at low temperatures, motility, and rRNA processing and is important for ribosomal maturation, being associated mainly with the 50S subunit of the ribosome.

Lmo2 expression defines tumor cell identity during T-cell leukemogenesis.

PubMed

García-Ramírez, Idoia; Bhatia, Sanil; Rodríguez-Hernández, Guillermo; González-Herrero, Inés; Walter, Carolin; González de Tena-Dávila, Sara; Parvin, Salma; Haas, Oskar; Woessmann, Wilhelm; Stanulla, Martin; Schrappe, Martin; Dugas, Martin; Natkunam, Yasodha; Orfao, Alberto; Domínguez, Verónica; Pintado, Belén; Blanco, Oscar; Alonso-López, Diego; De Las Rivas, Javier; Martín-Lorenzo, Alberto; Jiménez, Rafael; García Criado, Francisco Javier; García Cenador, María Begoña; Lossos, Izidore S; Vicente-Dueñas, Carolina; Borkhardt, Arndt; Hauer, Julia; Sánchez-García, Isidro

2018-06-07

The impact of LMO2 expression on cell lineage decisions during T-cell leukemogenesis remains largely elusive. Using genetic lineage tracing, we have explored the potential of LMO2 in dictating a T-cell malignant phenotype. We first initiated LMO2 expression in hematopoietic stem/progenitor cells and maintained its expression in all hematopoietic cells. These mice develop exclusively aggressive human-like T-ALL In order to uncover a potential exclusive reprogramming effect of LMO2 in murine hematopoietic stem/progenitor cells, we next showed that transient LMO2 expression is sufficient for oncogenic function and induction of T-ALL The resulting T-ALLs lacked LMO2 and its target-gene expression, and histologically, transcriptionally, and genetically similar to human LMO2-driven T-ALL We next found that during T-ALL development, secondary genomic alterations take place within the thymus. However, the permissiveness for development of T-ALL seems to be associated with wider windows of differentiation than previously appreciated. Restricted Cre-mediated activation of Lmo2 at different stages of B-cell development induces systematically and unexpectedly T-ALL that closely resembled those of their natural counterparts. Together, these results provide a novel paradigm for the generation of tumor T cells through reprogramming in vivo and could be relevant to improve the response of T-ALL to current therapies. © 2018 The Authors. Published under the terms of the CC BY 4.0 license.

Interpretation of Ferroan Anorthosite Ages and Implications for the Lunar Magma Ocean

NASA Technical Reports Server (NTRS)

Neal, C. R.; Draper, D. S.

2017-01-01

Ferroan Anorthosites (FANs) are considered to have purportedly crystallized directly from the lunar magma ocean (LMO) as a flotation crust. LMO modeling suggests that such anorthosites started to form only after greater than 70 percent of the LMO had crystallized. Recent age dates for FANs have questioned this hypothesis as they span too large of an age range. This means a younger age for the Moon-forming giant impact or the LMO hypothesis is flawed. However, FANs are notoriously difficult to age-date using the isochron method. We have proposed a mechanism for testing the LMO hypothesis through using plagioclase trace element abundances to calculate equilibrium liquids and compare them with LMO crystallization models. We now examine the petrography of the samples that have Sm-Nd (Samarium-Neodymium) age dates (Rb-Sr (Rubidium-Strontium) isotopic systematics may have been disturbed) and propose a relative way to age date FANs.

Top-down solidification of lunar magma ocean

NASA Astrophysics Data System (ADS)

Zhu, D.; Zhang, M.; Xu, Y.

2017-12-01

The early Moon was wholly or mostly molten, known as Lunar Magma Ocean (LMO) [1]. Most models suggest that the solidification of the LMO is bottom-up crystallization, because the liquidus temperature of the LMO increases with pressure more quickly than the adiabatic temperature [2]. In addition, the quenched lid is simply assumed to founder into the LMO [3, 4], because this solid lid is denser than the magma ocean liquids. Therefore, the dominated model for the solidification of the LMO is: olivine and pyroxene crystallized first at the base of the LMO and form the Moon's mantle; after ˜80% of the LMO had solidified, plagioclase began to crystallize and floated from dense silicate melt to the surface to form a global crust of anorthosite [5]. However, as the observational data on lunar meteorites accumulated, the standard model received challenges [6, 7]. Here we propose a new model suggesting the solidification of the LMO is top-down. Our model considers that olivine, pyroxene and plagioclase would crystalize at the mush region between the initially quenched lid and the interior of the LMO at the initial stage. Then the crystallized plagioclase floated and collected at the Moon's surface to form a stable anorthosite-crust; while the crystallized olivine and pyroxene would descend into the LMO and completely remelt away because the LMO interior is super-liquidus [2]. The overall result of our model is that plagioclase existed stably prior to olivine and pyroxene, rather than it crystallized after ˜80% LMO solidification. So, the model here is fundamentally different from previous models [5]. The plagioclase can crystallize from the very beginning to the end of the LMO, that is consistent with the ancient anorthosite age and long anorthosite-crystallization span which is over 200 Myr [6]. Importantly, our model can explain the coexistence of ferroan and magnesian anorthosite [7]. In addition, it is also understandable that the whole lunar mantle is depleted in Eu, Al2O3 and enriched in FeO and TiO2. [1] Wood, J.A. (1986) in Origin of the Moon, 17; [2] Solomatov et al. (2000), in Origin of the Earth and Moon, 323; [3] Spera (1992) GCA 56, 2253; [4] Walker et al. (1980) LPSC, 1196; [5] Snyder et al. (1992) GCA 56, 3809; [6] Pernet-Fisher et al. (2016) Astronomy & Geophysics 57, 1.26; [7] Gross et al. (2014) EPSL 388, 318.

Re-impacting Debris Facilitated Cooling of the Lunar Magma Ocean

NASA Astrophysics Data System (ADS)

Perera, Viranga; Jackson, Alan; Elkins-Tanton, Linda T.; Asphaug, Erik

2017-10-01

It is widely believed that the Moon formed from the debris of a giant impact between the proto-Earth and a roughly Mars-sized body. Concomitant to this formation scenario, and also inferred from geochemical analyses of Apollo samples, is the past existence of a Lunar Magma Ocean (LMO). After about 80% of the LMO solidified, it is believed that the mineral plagioclase would have become stable and crystallized out of the LMO. Rocks that formed principally of plagioclase would have been buoyant in the residual liquid and thus helped form a floatation crust that acted as a thermally conductive blanket over the LMO. Previous modelling work found that the LMO would have solidified in about 10 Myr. However, studies have shown that, during the giant impact event, a large quantity of debris (totaling over a Lunar mass) would have been released that was not immediately incorporated into the Earth and the Moon. This material would have subsequently re-impacted the Earth and the Moon. Particularly for the Moon, this debris would have punctured holes into the nascent lunar crust, attenuated its thermal blanketing effect, and thus facilitated the cooling of the LMO. We improve upon previous studies of the solidification of the LMO by incorporating this re-impacting debris, and find that the re-impacting debris may have reduced the LMO solidification time.

Driven by Affect to Explore Asteroids, the Moon, and Science Education

NASA Astrophysics Data System (ADS)

Dingatantrige Perera, Jude Viranga

Affect is a domain of psychology that includes attitudes, emotions, interests, and values. My own affect influenced the choice of topics for my dissertation. After examining asteroid interiors and the Moon's thermal evolution, I discuss the role of affect in online science education. I begin with asteroids, which are collections of smaller objects held together by gravity and possibly cohesion. These "rubble-pile" objects may experience the Brazil Nut Effect (BNE). When a collection of particles of similar densities, but of different sizes, is shaken, smaller particles will move parallel to the local gravity vector while larger objects will do the opposite. Thus, when asteroids are shaken by impacts, they may experience the BNE as possibly evidenced by large boulders seen on their surfaces. I found while the BNE is plausible on asteroids, it is confined to only the outer layers. The Moon, which formed with a Lunar Magma Ocean (LMO), is the next topic of this work. The LMO is due to the Moon forming rapidly after a giant impact between the proto-Earth and another planetary body. The first 80% of the LMO solidified rapidly at which point a floatation crust formed and slowed solidification of the remaining LMO. Impact bombardment during this cooling process, while an important component, has not been studied in detail. Impacts considered here are from debris generated during the formation of the Moon. I developed a thermal model that incorporates impacts and find that impacts may have either expedited or delayed LMO solidification. Finally, I return to affect to consider the differences in attitudes towards science between students enrolled in fully-online degree programs and those enrolled in traditional, in-person degree programs. I analyzed pre- and post-course survey data from the online astrobiology course Habitable Worlds. Unlike their traditional program counterparts, students enrolled in online programs started the course with better attitudes towards science and also further changed towards more positive attitudes during the course. Along with important conclusions in three research fields, this work aims to demonstrate the importance of affect in both scientific research and science education.

The absence of N-acetylglucosamine in wall teichoic acids of Listeria monocytogenes modifies biofilm architecture and tolerance to rinsing and cleaning procedures

PubMed Central

Faille, Christine; Sadovskaya, Irina; Charbit, Alain; Benezech, Thierry; Shen, Yang; Loessner, Martin J.; Bautista, Jean Romain; Midelet-Bourdin, Graziella

2018-01-01

The wall teichoic acid (WTA) is the major carbohydrate found within the extracellular matrix of the Listeria monocytogenes biofilm. We first addressed the frequency of spontaneous mutations in two genes (lmo2549 and lmo2550) responsible for the GlcNAcylation in 93 serotype 1/2a strains that were mainly isolated from seafood industries. We studied the impact of mutations in lmo2549 or lmo2550 genes on biofilm formation by using one mutant carrying a natural mutation inactivating the lmo2550 gene (DSS 1130 BFA2 strain) and two EGD-e mutants that lack respective genes by in-frame deletion of lmo2549 or lmo2550 using splicing-by-overlap-extension PCR, followed by allelic exchange mutagenesis. The lmo2550 gene mutation, occurring in around 50% isolates, caused a decrease in bacterial adhesion to stainless steel compared to wild-type EGD-e strain during the adhesion step. On the other hand, bacterial population weren’t significantly different after 24h-biofilm formation. The biofilm architecture was different between the wild-type strain and the two mutants inactivated for lmo2549 or lmo2550 genes respectively with the presence of bacterial micro-colonies for mutants which were not observed in the wild-type EGD-e strain biofilm. These differences might account for the stronger hydrophilic surface exhibited by the mutant cells. Upon a water flow or to a cleaning procedure at a shear stress of 0.16 Pa, the mutant biofilms showed the higher detachment rate compared to wild-type strain. Meanwhile, an increase in the amount of residual viable but non-culturable population on stainless steel was recorded in two mutants. Our data suggests that the GlcNAc residue of WTA played a role in adhesion and biofilm formation of Listeria monocyctogenes. PMID:29320565

Nuclear localization of lymphocyte-specific protein tyrosine kinase (Lck) and its role in regulating LIM domain only 2 (Lmo2) gene

DOE Office of Scientific and Technical Information (OSTI.GOV)

Venkitachalam, Srividya; Chueh, Fu-Yu; Yu, Chao-Lan, E-mail: chaolan.yu@rosalindfranklin.edu

2012-01-20

Highlights: Black-Right-Pointing-Pointer Lmo2 expression is elevated in Lck-transformed cells. Black-Right-Pointing-Pointer Both endogenous and exogenous Lck localize in the nucleus. Black-Right-Pointing-Pointer Nuclear Lck is active in Lck-transformed cells. Black-Right-Pointing-Pointer Lck binds to the promoter region of Lmo2 gene in vivo. Black-Right-Pointing-Pointer In contrast to JAK2, Lck does not increase histone H3 phosphorylation on Tyr 41. -- Abstract: LIM domain only protein 2 (Lmo2) is a transcription factor that plays a critical role in the development of T-acute lymphoblastic leukemia (T-ALL). A previous report established a link between Lmo2 expression and the nuclear presence of oncogenic Janus kinase 2 (JAK2), a non-receptormore » protein tyrosine kinase. The oncogenic JAK2 kinase phosphorylates histone H3 on Tyr 41 that leads to the relief of Lmo2 promoter repression and subsequent gene expression. Similar to JAK2, constitutive activation of lymphocyte-specific protein tyrosine kinase (Lck) has been implicated in lymphoid malignancies. However, it is not known whether oncogenic Lck regulates Lmo2 expression through a similar mechanism. We show here that Lmo2 expression is significantly elevated in T cell leukemia LSTRA overexpressing active Lck kinase and in HEK 293 cells expressing oncogenic Y505FLck kinase. Nuclear localization of active Lck kinase was confirmed in both Lck-transformed cells by subcellular fractionation and immunofluorescence microscopy. More importantly, in contrast to oncogenic JAK2, oncogenic Lck kinase does not result in significant increase in histone H3 phosphorylation on Tyr 41. Instead, chromatin immunoprecipitation experiment shows that oncogenic Y505FLck kinase binds to the Lmo2 promoter in vivo. This result raises the possibility that oncogenic Lck may activate Lmo2 promoter through direct interaction.« less

The absence of N-acetylglucosamine in wall teichoic acids of Listeria monocytogenes modifies biofilm architecture and tolerance to rinsing and cleaning procedures.

PubMed

Brauge, Thomas; Faille, Christine; Sadovskaya, Irina; Charbit, Alain; Benezech, Thierry; Shen, Yang; Loessner, Martin J; Bautista, Jean Romain; Midelet-Bourdin, Graziella

2018-01-01

The wall teichoic acid (WTA) is the major carbohydrate found within the extracellular matrix of the Listeria monocytogenes biofilm. We first addressed the frequency of spontaneous mutations in two genes (lmo2549 and lmo2550) responsible for the GlcNAcylation in 93 serotype 1/2a strains that were mainly isolated from seafood industries. We studied the impact of mutations in lmo2549 or lmo2550 genes on biofilm formation by using one mutant carrying a natural mutation inactivating the lmo2550 gene (DSS 1130 BFA2 strain) and two EGD-e mutants that lack respective genes by in-frame deletion of lmo2549 or lmo2550 using splicing-by-overlap-extension PCR, followed by allelic exchange mutagenesis. The lmo2550 gene mutation, occurring in around 50% isolates, caused a decrease in bacterial adhesion to stainless steel compared to wild-type EGD-e strain during the adhesion step. On the other hand, bacterial population weren't significantly different after 24h-biofilm formation. The biofilm architecture was different between the wild-type strain and the two mutants inactivated for lmo2549 or lmo2550 genes respectively with the presence of bacterial micro-colonies for mutants which were not observed in the wild-type EGD-e strain biofilm. These differences might account for the stronger hydrophilic surface exhibited by the mutant cells. Upon a water flow or to a cleaning procedure at a shear stress of 0.16 Pa, the mutant biofilms showed the higher detachment rate compared to wild-type strain. Meanwhile, an increase in the amount of residual viable but non-culturable population on stainless steel was recorded in two mutants. Our data suggests that the GlcNAc residue of WTA played a role in adhesion and biofilm formation of Listeria monocyctogenes.

Spatial distribution of transferred charges across the heterointerface between perovskite transition metal oxides LaNiO{sub 3} and LaMnO{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kitamura, Miho; Photon Factory, Institute of Materials Structure Science, High Energy Accelerator Research Organization; Horiba, Koji

2016-03-14

To investigate the interfacial charge-transfer phenomena between perovskite transition metal oxides LaNiO{sub 3} (LNO) and LaMnO{sub 3} (LMO), we have performed in situ x-ray absorption spectroscopy (XAS) measurements on LNO/LMO multilayers. The Ni-L{sub 2,3} and Mn-L{sub 2,3} XAS spectra clearly show the occurrence of electron transfer from Mn to Ni ions in the interface region. Detailed analysis of the thickness dependence of these XAS spectra has revealed that the spatial distribution of the transferred charges across the interface is significantly different between the two constituent layers. The observed spatial distribution is presumably described by the charge spreading model that treatsmore » the transfer integral between neighboring transition metal ions and the Coulomb interaction, rather than the Thomas–Fermi screening model.« less

Lmo1656 is a secreted virulence factor of Listeria monocytogenes that interacts with the sorting nexin 6-BAR complex.

PubMed

David, Daryl Jason; Pagliuso, Alessandro; Radoshevich, Lilliana; Nahori, Marie-Anne; Cossart, Pascale

2018-06-15

Listeria monocytogenes ( Lm ) is a facultative intracellular bacterial pathogen and the causative agent of listeriosis, a rare but fatal disease. During infection, Lm can traverse several physiological barriers; it can cross the intestine and placenta barrier and, in immunocompromised individuals, the blood-brain barrier. With the recent plethora of sequenced genomes available for Lm , it is clear that the complete repertoire of genes used by Lm to interact with its host remains to be fully explored. Recently, we focused on secreted Lm proteins because they are likely to interact with host cell components. Here, we investigated a putatively secreted protein of Lm , Lmo1656, that is present in most sequenced strains of Lm but absent in the nonpathogenic species Listeria innocua. lmo1656 gene is predicted to encode a small, positively charged protein. We show that Lmo1656 is secreted by Lm Furthermore, deletion of the lmo1656 gene (Δ lmo1656 ) attenuates virulence in mice infected orally but not intravenously, suggesting that Lmo1656 plays a role during oral listeriosis. We identified sorting nexin 6 (SNX6), an endosomal sorting component and BAR domain-containing protein, as a host cell interactor of Lmol656. SNX6 colocalizes with WT Lm during the early steps of infection. This colocalization depends on Lmo1656, and RNAi of SNX6 impairs infection in infected tissue culture cells, suggesting that SNX6 is utilized by Lm during infection. Our results reveal that Lmo1656 is a novel secreted virulence factor of Lm that facilitates recruitment of a specific member of the sorting nexin family in the mammalian host. © 2018 by The American Society for Biochemistry and Molecular Biology, Inc.

Effect of capping layer on spin-orbit torques

NASA Astrophysics Data System (ADS)

Sun, Chi; Siu, Zhuo Bin; Tan, Seng Ghee; Yang, Hyunsoo; Jalil, Mansoor B. A.

2018-04-01

In order to enhance the magnitude of spin-orbit torque (SOT), considerable experimental works have been devoted to studying the thickness dependence of the different layers in multilayers consisting of heavy metal (HM), ferromagnet (FM), and capping layers. Here, we present a theoretical model based on the spin-drift-diffusion formalism to investigate the effect of the capping layer properties such as its thickness on the SOT observed in experiments. It is found that the spin Hall-induced SOT can be significantly enhanced by incorporating a capping layer with an opposite spin Hall angle to that of the HM layer. The spin Hall torque can be maximized by tuning the capping layer thickness. However, in the absence of the spin Hall effect (SHE) in the capping layer, the torque decreases monotonically with the capping layer thickness. Conversely, the spin Hall torque is found to decrease monotonically with the FM layer thickness, irrespective of the presence or absence of the SHE in the capping layer. All these trends are in correspondence with experimental observations. Finally, our model suggests that capping layers with a long spin diffusion length and high resistivity would also enhance the spin Hall torque.

Are Ferroan Anorthosites Direct Products of the Lunar Magma Ocean?

NASA Technical Reports Server (NTRS)

Neal, C. R.; Draper, D. S.

2016-01-01

According to Lunar Magma Ocean (LMO) theory, lunar samples that fall into the ferroan anorthosite (FAN) category represent the only samples we have of of the primordial crust of the Moon. Modeling indicates that plagioclase crystallizes after >70% LMO crystallization and formed a flotation crust, depending upon starting composition. The FAN group of highlands materials has been subdivided into mafic-magnesian, mafic-ferroan, anorthositic- sodic, and anorthositic-ferroan, although it is not clear how these subgroups are related. Recent radiogenic isotope work has suggested the range in FAN ages and isotopic systematics are inconsistent with formation of all FANs from the LMO. While an insulating lid could have theoretically extend the life of the LMO to explain the range of the published ages, are the FAN compositions consistent with crystallization from the LMO? As part of a funded Emerging Worlds proposal (NNX15AH76G), we examine this question through analysis of FAN samples. We compare the results with various LMO crystallization models, including those that incorporate the influence of garnet.

Variations in biofilm formation, desiccation resistance and Benzalkonium chloride susceptibility among Listeria monocytogenes strains isolated in Canada.

PubMed

Piercey, Marta J; Ells, Timothy C; Macintosh, Andrew J; Truelstrup Hansen, Lisbeth

2017-09-18

Listeria monocytogenes is a pathogenic foodborne microorganism noted for its ability to survive in the environment and food processing facilities. Survival may be related to the phenotype of individual strains including the ability to form biofilms and resist desiccation and/or sanitizer exposure. The objectives of this research were to compare 14 L. monocytogenes strains isolated from blood (3), food (6) and water (5) with respect to their benzalkonium chloride (BAC) sensitivity, desiccation resistance, and ability to form biofilm. Correlations were tested between those responses, and the presence of the SSI-1 (Stress Survival Islet) and LGI1/CC8 (Listeria Genomic Island 1 in a clonal complex 8 background) genetic markers. Genetic sequences from four strains representing different phenotypes were also probed for predicted amino acid differences in biofilm, desiccation, and membrane related genes. The water isolates were among the most desiccation susceptible strains, while strains exhibiting desiccation resistance harboured SSI-1 or both the SSI-1 and LGI1/CC8 markers. BAC resistance was greatest in planktonic LGI1/CC8 cells (relative to non-LGI1/CC8 cells), and higher BAC concentrations were also needed to inhibit the formation of biofilm by LGI1/CC8 strains during incubation for 48h and 6days compared to other strains. Formation of biofilm on stainless steel was not significantly (p>0.05) different among the strains. Analysis of genetic sequence data from desiccation and BAC sensitive (CP4 5-1, CP5 2-3, both from water), intermediate (Lm568, food) and desiccation and BAC resistant (08 5578, blood, human outbreak) strains led to the finding of amino acid differences in predicted functional protein domains in several biofilm, desiccation and peptidoglycan related genes (e.g., lmo0263, lmo0433, lmo0434, lmo0771, lmo0973, lmo1080, lmo1224, lmo1370, lmo1744, and lmo2558). Notably, the LGI1/CC8 strain 08-5578 had a frameshift mutation in lmo1370, a gene previously associated with desiccation resistance. In conclusion, the more desiccation and BAC resistant LGI1/CC8 isolates may pose a challenge for sanitation efforts. Crown Copyright © 2017. Published by Elsevier B.V. All rights reserved.

Overexpression of Lhx2 suppresses proliferation of human T cell acute lymphoblastic leukemia-derived cells, partly by reducing LMO2 protein levels.

PubMed

Miyashita, Kazuya; Kitajima, Kenji; Goyama, Susumu; Kitamura, Toshio; Hara, Takahiko

2018-01-15

T cell acute lymphoblastic leukemia (T-ALL) is a malignant cancer with poor prognosis. The transcriptional co-factor LIM domain only 2 (LMO2) and its target gene HHEX are essential for self-renewal of T cell precursors and T-ALL etiology. LMO2 directly associates with LDB1 in a large DNA-containing nuclear complex and controls the transcription of T-ALL-related genes. Recently, we reported that overexpression of the LIM-homeodomain transcription factor, Lhx2, results in liberation of the Lmo2 protein from the Lmo2-Ldb1 complex, followed by ubiquitin proteasome mediated degradation. Here, we found that proliferation of five human T-ALL-derived cell lines, including CCRF-CEM, was significantly suppressed by retroviral overexpression of Lhx2. The majority of Lhx2-transduced CCRF-CEM cells arrested in G 0 phase and subsequently underwent apoptosis. Expression of LMO2 protein as well as HHEX, ERG, HES1 and MYC genes was repressed in CCRF-CEM cells by transduction with Lhx2. Lhx2-mediated growth inhibition was partially rescued by simultaneous overexpression of Lmo2; however, both the C-terminal LIM domain and the homeodomain of Lhx2 were required for its growth-suppressive activity. These data indicate that Lhx2 is capable of blocking proliferation of T-ALL-derived cells by both LMO2-dependent and -independent means. We propose Lhx2 as a new molecular tool for anti-T-ALL drug development. Copyright © 2017 Elsevier Inc. All rights reserved.

An experimental system for the evaluation of retroviral vector design to diminish the risk for proto-oncogene activation

PubMed Central

Ryu, Byoung Y.; Evans-Galea, Marguerite V.; Gray, John T.; Bodine, David M.; Persons, Derek A.

2008-01-01

Pathogenic activation of the LMO2 proto-oncogene by an oncoretroviral vector insertion in a clinical trial for X-linked severe combined immunodeficiency (X-SCID) has prompted safety concerns. We used an adeno-associated virus vector to achieve targeted insertion of a γ-retroviral long terminal repeat (LTR) driving a GFP expression cassette with flanking loxP sites in a human T-cell line at the precise location of vector integration in one of the patients with X-SCID. The LTR-GFP cassette was inserted into the first intron of the LMO2 gene, resulting in strong activation of LMO2. Cre-mediated cassette exchange was used to replace the original LTR-GFP cassette with one flanked by insulator elements leading to a several fold reduction in LMO2 expression. The LTR-GFP cassette was also replaced with a globin gene regulatory cassette that failed to activate the LMO2 gene in lymphoid cells. A γ-retroviral vector with 2 intact LTRs resulted in activation of the LMO2 gene when inserted into the first intron, but a self-inactivating lentiviral vector with an internal cellular promoter and flanking insulator elements did not activate the LMO2 gene. Thus, this system is useful for comparing the safety profiles of vector cassettes with various regulatory elements for their potential for proto-oncogene activation. PMID:17991809

N-acetylglucosamine-6-phosphate deacetylase (NagA) of Listeria monocytogenes EGD, an essential enzyme for the metabolism and recycling of amino sugars.

PubMed

Popowska, Magdalena; Osińska, Magdalena; Rzeczkowska, Magdalena

2012-04-01

The main aim of our study was to determine the physiological function of NagA enzyme in the Listeria monocytogenes cell. The primary structure of the murein of L. monocytogenes is very similar to that of Escherichia coli, the main differences being amidation of diaminopimelic acid and partial de-N-acetylation of glucosamine residues. NagA is needed for the deacetylation of N-acetyl-glucosamine-6 phosphate to glucosamine-6 phosphate and acetate. Analysis of the L. monocytogenes genome reveals the presence of two proteins with NagA domain, Lmo0956 and Lmo2108, which are cytoplasmic putative proteins. We introduced independent mutations into the structural genes for the two proteins. In-depth characterization of one of these mutants, MN1, deficient in protein Lmo0956 revealed strikingly altered cell morphology, strongly reduced cell wall murein content and decreased sensitivity to cell wall hydrolase, mutanolysin and peptide antibiotic, colistin. The gene products of operon 150, consisting of three genes: lmo0956, lmo0957, and lmo0958, are necessary for the cytosolic steps of the amino-sugar-recycling pathway. The cytoplasmic de-N-acetylase Lmo0956 of L. monocytogenes is required for cell wall peptidoglycan and teichoic acid biosynthesis and is also essential for bacterial cell growth, cell division, and sensitivity to cell wall hydrolases and peptide antibiotics.

Uptake and Metabolism of Antibiotics Roseoflavin and 8-Demethyl-8-Aminoriboflavin in Riboflavin-Auxotrophic Listeria monocytogenes.

PubMed

Matern, Andreas; Pedrolli, Danielle; Großhennig, Stephanie; Johansson, Jörgen; Mack, Matthias

2016-12-01

The riboflavin analogs roseoflavin (RoF) and 8-demethyl-8-aminoriboflavin (AF) are produced by the bacteria Streptomyces davawensis and Streptomyces cinnabarinus Riboflavin analogs have the potential to be used as broad-spectrum antibiotics, and we therefore studied the metabolism of riboflavin (vitamin B 2 ), RoF, and AF in the human pathogen Listeria monocytogenes, a bacterium which is a riboflavin auxotroph. We show that the L. monocytogenes protein Lmo1945 is responsible for the uptake of riboflavin, RoF, and AF. Following import, these flavins are phosphorylated/adenylylated by the bifunctional flavokinase/flavin adenine dinucleotide (FAD) synthetase Lmo1329 and adenylylated by the unique FAD synthetase Lmo0728, the first monofunctional FAD synthetase to be described in bacteria. Lmo1329 generates the cofactors flavin mononucleotide (FMN) and FAD, whereas Lmo0728 produces FAD only. The combined activities of Lmo1329 and Lmo0728 are responsible for the intracellular formation of the toxic cofactor analogs roseoflavin mononucleotide (RoFMN), roseoflavin adenine dinucleotide (RoFAD), 8-demethyl-8-aminoriboflavin mononucleotide (AFMN), and 8-demethyl-8-aminoriboflavin adenine dinucleotide (AFAD). In vivo reporter gene assays and in vitro transcription/translation experiments show that the L. monocytogenes FMN riboswitch Rli96, which controls expression of the riboflavin transport gene lmo1945, is negatively affected by riboflavin/FMN and RoF/RoFMN but not by AF/AFMN. Treatment of L. monocytogenes with RoF or AF leads to drastically reduced FMN/FAD levels. We suggest that the reduced flavin cofactor levels in combination with concomitant synthesis of inactive cofactor analogs (RoFMN, RoFAD, AFMN, and AFAD) explain why RoF and AF contribute to antibiotic activity in L. monocytogenes IMPORTANCE: The riboflavin analogs roseoflavin (RoF) and 8-demethyl-8-aminoriboflavin (AF) are small molecules which are produced by Streptomyces davawensis and Streptomyces cinnabarinus RoF and AF were reported to have antibacterial activity, and we studied how these compounds are metabolized by the human bacterial pathogen Listeria monocytogenes We found that the L. monocytogenes protein Lmo1945 mediates uptake of AF and RoF and that the combined activities of the enzymes Lmo1329 and Lmo0728 are responsible for the conversion of AF and RoF to toxic cofactor analogs. Comparative studies with RoF and AF (a weaker antibiotic) suggest that the reduction in FMN/FAD levels and the formation of inactive FMN/FAD analogs explain to a large extent the antibiotic activity of AF and RoF. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Cross-plane electronic and thermal transport properties of p-type La0.67Sr0.33MnO3/LaMnO3 perovskite oxide metal/semiconductor superlattices

NASA Astrophysics Data System (ADS)

Jha, Pankaj; Sands, Timothy D.; Cassels, Laura; Jackson, Philip; Favaloro, Tela; Kirk, Benjamin; Zide, Joshua; Xu, Xianfan; Shakouri, Ali

2012-09-01

Lanthanum strontium manganate (La0.67Sr0.33MnO3, i.e., LSMO)/lanthanum manganate (LaMnO3, i.e., LMO) perovskite oxide metal/semiconductor superlattices were investigated as a potential p-type thermoelectric material. Growth was performed using pulsed laser deposition to achieve epitaxial LSMO (metal)/LMO (p-type semiconductor) superlattices on (100)-strontium titanate (STO) substrates. The magnitude of the in-plane Seebeck coefficient of LSMO thin films (<20 μV/K) is consistent with metallic behavior, while LMO thin films were p-type with a room temperature Seebeck coefficient of 140 μV/K. Thermal conductivity measurements via the photo-acoustic (PA) technique showed that LSMO/LMO superlattices exhibit a room temperature cross-plane thermal conductivity (0.89 W/m.K) that is significantly lower than the thermal conductivity of individual thin films of either LSMO (1.60 W/m.K) or LMO (1.29 W/m.K). The lower thermal conductivity of LSMO/LMO superlattices may help overcome one of the major limitations of oxides as thermoelectrics. In addition to a low cross-plane thermal conductivity, a high ZT requires a high power factor (S2σ). Cross-plane electrical transport measurements were carried out on cylindrical pillars etched in LSMO/LMO superlattices via inductively coupled plasma reactive ion etching. Cross-plane electrical resistivity data for LSMO/LMO superlattices showed a magnetic phase transition temperature (TP) or metal-semiconductor transition at ˜330 K, which is ˜80 K higher than the TP observed for in-plane resistivity of LSMO, LMO, or LSMO/LMO thin films. The room temperature cross-plane resistivity (ρc) was found to be greater than the in-plane resistivity by about three orders of magnitude. The magnitude and temperature dependence of the cross-plane conductivity of LSMO/LMO superlattices suggests the presence of a barrier with the effective barrier height of ˜300 meV. Although the magnitude of the cross-plane power factor is too low for thermoelectric applications by a factor of approximately 10-4—in part because the growth conditions chosen for this study yielded relatively high resistivity films—the temperature dependence of the resistivity and the potential for tuning the power factor by engineering strain, oxygen stoichiometry, and electronic band structure suggest that these epitaxial metal/semiconductor superlattices are deserving of further investigation.

Targeting nitrative stress for attenuating cisplatin-induced downregulation of cochlear LIM domain only 4 and ototoxicity.

PubMed

Jamesdaniel, Samson; Rathinam, Rajamani; Neumann, William L

2016-12-01

Cisplatin-induced ototoxicity remains a primary dose-limiting adverse effect of this highly effective anticancer drug. The clinical utility of cisplatin could be enhanced if the signaling pathways that regulate the toxic side-effects are delineated. In previous studies, we reported cisplatin-induced nitration of cochlear proteins and provided the first evidence for nitration and downregulation of cochlear LIM domain only 4 (LMO4) in cisplatin ototoxicity. Here, we extend these findings to define the critical role of nitrative stress in cisplatin-induced downregulation of LMO4 and its consequent ototoxic effects in UBOC1 cell cultures derived from sensory epithelial cells of the inner ear and in CBA/J mice. Cisplatin treatment increased the levels of nitrotyrosine and active caspase 3 in UBOC1 cells, which was detected by immunocytochemical and flow cytometry analysis, respectively. The cisplatin-induced nitrative stress and apoptosis were attenuated by co-treatment with SRI110, a peroxynitrite decomposition catalyst (PNDC), which also attenuated the cisplatin-induced downregulation of LMO4 in a dose-dependent manner. Furthermore, transient overexpression of LMO4 in UBOC1 cells prevented cisplatin-induced cytotoxicity while repression of LMO4 exacerbated cisplatin-induced cell death, indicating a direct link between LMO4 protein levels and cisplatin ototoxicity. Finally, auditory brainstem responses (ABR) recorded from CBA/J mice indicated that co-treatment with SRI110 mitigated cisplatin-induced hearing loss. Together, these results suggest that cisplatin-induced nitrative stress leads to a decrease in the levels of LMO4, downregulation of LMO4 is a critical determinant in cisplatin-induced ototoxicity, and targeting peroxynitrite could be a promising strategy for mitigating cisplatin-induced hearing loss. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

LMO1 Synergizes with MYCN to Promote Neuroblastoma Initiation and Metastasis.

PubMed

Zhu, Shizhen; Zhang, Xiaoling; Weichert-Leahey, Nina; Dong, Zhiwei; Zhang, Cheng; Lopez, Gonzalo; Tao, Ting; He, Shuning; Wood, Andrew C; Oldridge, Derek; Ung, Choong Yong; van Ree, Janine H; Khan, Amish; Salazar, Brittany M; Lummertz da Rocha, Edroaldo; Zimmerman, Mark W; Guo, Feng; Cao, Hong; Hou, Xiaonan; Weroha, S John; Perez-Atayde, Antonio R; Neuberg, Donna S; Meves, Alexander; McNiven, Mark A; van Deursen, Jan M; Li, Hu; Maris, John M; Look, A Thomas

2017-09-11

A genome-wide association study identified LMO1, which encodes an LIM-domain-only transcriptional cofactor, as a neuroblastoma susceptibility gene that functions as an oncogene in high-risk neuroblastoma. Here we show that dβh promoter-mediated expression of LMO1 in zebrafish synergizes with MYCN to increase the proliferation of hyperplastic sympathoadrenal precursor cells, leading to a reduced latency and increased penetrance of neuroblastomagenesis. The transgenic expression of LMO1 also promoted hematogenous dissemination and distant metastasis, which was linked to neuroblastoma cell invasion and migration, and elevated expression levels of genes affecting tumor cell-extracellular matrix interaction, including loxl3, itga2b, itga3, and itga5. Our results provide in vivo validation of LMO1 as an important oncogene that promotes neuroblastoma initiation, progression, and widespread metastatic dissemination. Copyright © 2017 Elsevier Inc. All rights reserved.

LMO4 is essential for paraventricular hypothalamic neuronal activity and calcium channel expression to prevent hyperphagia.

PubMed

Zaman, Tariq; Zhou, Xun; Pandey, Nihar R; Qin, Zhaohong; Keyhanian, Kianoosh; Wen, Kendall; Courtney, Ryan D; Stewart, Alexandre F R; Chen, Hsiao-Huei

2014-01-01

The dramatic increase in the prevalence of obesity reflects a lack of progress in combating one of the most serious health problems of this century. Recent studies have improved our understanding of the appetitive network by focusing on the paraventricular hypothalamus (PVH), a key region responsible for the homeostatic balance of food intake. Here we show that mice with PVH-specific ablation of LIM domain only 4 (Lmo4) become rapidly obese when fed regular chow due to hyperphagia rather than to reduced energy expenditure. Brain slice recording of LMO4-deficient PVH neurons showed reduced basal cellular excitability together with reduced voltage-activated Ca(2+) currents. Real-time PCR quantification revealed that LMO4 regulates the expression of Ca(2+) channels (Cacna1h, Cacna1e) that underlie neuronal excitability. By increasing neuronal activity using designer receptors exclusively activated by designer drugs technology, we could suppress food intake of PVH-specific LMO4-deficient mice. Together, these results demonstrate that reduced neural activity in LMO4-deficient PVH neurons accounts for hyperphagia. Thus, maintaining PVH activity is important to prevent hyperphagia-induced obesity.

REE and Isotopic Compositions of Lunar Basalts Demonstrate Partial Melting of Hybridized Mantle Sources after Cumulate Overturn is Required

NASA Astrophysics Data System (ADS)

Dygert, N. J.; Liang, Y.

2017-12-01

Lunar basalts maintain an important record of the composition of the lunar interior. Much of our understanding of the Moon's early evolution comes from studying their petrogenesis. Recent experimental work has advanced our knowledge of major and trace element fractionation during lunar magma ocean (LMO) crystallization [e.g., 1-3], which produced heterogeneous basalt sources in the Moon's mantle. With the new experimental constraints, we can evaluate isotopic and trace element signatures in lunar basalts in unprecedented detail, refining inferences about the Moon's dynamic history. Two petrogenetic models are invoked to explain the compositions of the basalts. The assimilation model argues they formed as primitive melts of early LMO cumulates that assimilated late LMO cumulates as they migrated upward. The cumulate overturn model argues that dense LMO cumulates sank into the lunar interior, producing hybridized sources that melted to form the basalts. Here we compare predicted Ce/Yb and Hf and Nd isotopes of partial melts of LMO cumulates with measured compositions of lunar basalts to evaluate whether they could have formed by end-member petrogenetic models. LMO crystallization models suggest all LMO cumulates have chondrite normalized Ce/Yb <1. Residual liquid from the magma ocean has Ce/Yb 1.5. Many primitive lunar basalts have Ce/Yb>1.5; these could not have formed by assimilation of any LMO cumulate or residual liquid (or KREEP basalt, which has isotopically negative ɛNd and ɛHf). In contrast, basalt REE patterns and isotopes can easily be modeled assuming partial melting of hybridized mantle sources, indicating overturn may be required. A chemical requirement for overturn independently confirms that late LMO cumulates are sufficiently low in viscosity to sink into the lunar interior, as suggested by recent rock deformation experiments [4]. Overturned, low viscosity late LMO cumulates would be relatively stable around the core [5]. High Ce/Yb basalts require that overturned cumulates were mixed back into the overlying mantle by convection within a few hundred Myr. [1] Dygert et al. (2014), GCA 132, 170-186. [2] Sun et al. (2017), GCA 206, 273-295. [3] Lin et al. (2017), EPSL 471, 104-116. [4] Dygert et al. (2016), GRL 43, 10.1002/2015GL066546. [5] Zhang et al. (2017), GRL 44, 10.1002/2017GL073702.

Thermodynamic Stability of Low- and High-Index Spinel LiMn 2 O 4 Surface Terminations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warburton, Robert E.; Iddir, Hakim; Curtiss, Larry A.

2016-05-04

Density functional theory calculations are performed within the generalized gradient approximation (GGA+U) to determine stable terminations of both low- and high-index spinel LiMn2O4 (LMO) surfaces. A grand canonical thermodynamic approach is employed, permitting a direct comparison of offstoichiometric surfaces with previously reported stoichiometric surface terminations at various environmental conditions. Within this formalism, we have identified trends in the structure of the low-index surfaces as a function of the Li and O chemical potentials. The results suggest that, under a range of chemical potentials for which bulk LMO is stable, Li/O and Li-rich (111) surface terminations are favored, neither of whichmore » adopts an inverse spinel structure in the subsurface region. This thermodynamic analysis is extended to identify stable structures for certain high-index surfaces, including (311), (331), (511), and (531), which constitute simple models for steps or defects that may be present on real LMO particles. The low- and high-index results are combined to determine the relative stability of each surface facet under a range of environmental conditions. The relative surface energies are further employed to predict LMO particle shapes through a Wulff construction approach, which suggests that LMO particles will adopt either an octahedron or a truncated octahedron shape at conditions in which LMO is thermodynamically stable. These results are in agreement with the experimental observations of LMO particle shapes.« less

SCL, LMO1 and Notch1 Reprogram Thymocytes into Self-Renewing Cells

PubMed Central

Rojas-Sutterlin, Shanti; Herblot, Sabine; Hébert, Josée; Sauvageau, Guy; Lemieux, Sébastien; Lécuyer, Eric; Veiga, Diogo F. T.; Hoang, Trang

2014-01-01

The molecular determinants that render specific populations of normal cells susceptible to oncogenic reprogramming into self-renewing cancer stem cells are poorly understood. Here, we exploit T-cell acute lymphoblastic leukemia (T-ALL) as a model to define the critical initiating events in this disease. First, thymocytes that are reprogrammed by the SCL and LMO1 oncogenic transcription factors into self-renewing pre-leukemic stem cells (pre-LSCs) remain non-malignant, as evidenced by their capacities to generate functional T cells. Second, we provide strong genetic evidence that SCL directly interacts with LMO1 to activate the transcription of a self-renewal program coordinated by LYL1. Moreover, LYL1 can substitute for SCL to reprogram thymocytes in concert with LMO1. In contrast, inhibition of E2A was not sufficient to substitute for SCL, indicating that thymocyte reprogramming requires transcription activation by SCL-LMO1. Third, only a specific subset of normal thymic cells, known as DN3 thymocytes, is susceptible to reprogramming. This is because physiological NOTCH1 signals are highest in DN3 cells compared to other thymocyte subsets. Consistent with this, overexpression of a ligand-independent hyperactive NOTCH1 allele in all immature thymocytes is sufficient to sensitize them to SCL-LMO1, thereby increasing the pool of self-renewing cells. Surprisingly, hyperactive NOTCH1 cannot reprogram thymocytes on its own, despite the fact that NOTCH1 is activated by gain of function mutations in more than 55% of T-ALL cases. Rather, elevating NOTCH1 triggers a parallel pathway involving Hes1 and Myc that dramatically enhances the activity of SCL-LMO1 We conclude that the acquisition of self-renewal and the genesis of pre-LSCs from thymocytes with a finite lifespan represent a critical first event in T-ALL. Finally, LYL1 and LMO1 or LMO2 are co-expressed in most human T-ALL samples, except the cortical T subtype. We therefore anticipate that the self-renewal network described here may be relevant to a majority of human T-ALL. PMID:25522233

Experimental Simulations of Lunar Magma Ocean Crystallization: The Plot (But Not the Crust) Thickens

NASA Technical Reports Server (NTRS)

Draper, D. S.; Rapp, J. F.; Elardo, S. M.; Shearer, C. K., Jr.; Neal, C. R.

2016-01-01

Numerical models of differentiation of a global-scale lunar magma ocean (LMO) have raised as many questions as they have answered. Recent orbital missions and sample studies have provided new context for a large range of lithologies, from the comparatively magnesian "purest anorthosite" reported by to Si-rich domes and spinel-rich clasts with widespread areal distributions. In addition, the GRAIL mission provided strong constraints on lunar crustal density and average thickness. Can this increasingly complex geology be accounted for via the formation and evolution of the LMO? We have in recent years been conducting extensive sets of petrologic experiments designed to fully simulate LMO crystallization, which had not been attempted previously. Here we review the key results from these experiments, which show that LMO differentiation is more complex than initial models suggested. Several important features expected from LMO crystallization models have yet to be reproduced experimentally; combined modelling and experimental work by our group is ongoing.

GASDERMIN, suppressed frequently in gastric cancer, is a target of LMO1 in TGF-beta-dependent apoptotic signalling.

PubMed

Saeki, N; Kim, D H; Usui, T; Aoyagi, K; Tatsuta, T; Aoki, K; Yanagihara, K; Tamura, M; Mizushima, H; Sakamoto, H; Ogawa, K; Ohki, M; Shiroishi, T; Yoshida, T; Sasaki, H

2007-10-04

Defining apoptosis-regulatory cascades of the epithelium is important for understanding carcinogenesis, since cancer cells are considered to arise as a result of the collapse of the cascades. We previously reported that a novel gene GASDERMIN (GSDM) is expressed in the stomach but suppressed in gastric cancer cell lines. Furthermore, in this study, we demonstrated that GSDM is expressed in the mucus-secreting pit cells of the gastric epithelium and frequently silenced in primary gastric cancers. We found that GSDM has a highly apoptotic activity and its expression is regulated by a transcription factor LIM domain only 1 (LMO1) through a sequence to which Runt-related transcription factor 3 (RUNX3) binds, in a GSDM promoter region. We observed coexpression of GSDM with LMO1, RUNX3 and type II transforming growth factor-beta receptor (TGF-betaRII) in the pit cells, and found that TGF-beta upregulates the LMO1- and GSDM-expression in the gastric epithelial cell line and induces apoptosis, which was confirmed by the finding that the apoptosis induction is inhibited by suppression of each LMO1-, RUNX3- and GSDM expression, respectively. The present data suggest that TGF-beta, LMO1, possibly RUNX3, and GSDM form a regulatory pathway for directing the pit cells to apoptosis.

Crystallinity of tellurium capping and epitaxy of ferromagnetic topological insulator films on SrTiO 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Jihwey; Soh, Yeong-Ah; Aeppli, Gabriel

2015-06-30

Thin films of topological insulators are often capped with an insulating layer since topological insulators are known to be fragile to degradation. However, capping can hinder the observation of novel transport properties of the surface states. To understand the influence of capping on the surface states, it is crucial to understand the crystal structure and the atomic arrangement at the interfaces. Here, we use x-ray diffraction to establish the crystal structure of magnetic topological insulator Cr-doped (Bi,Sb) 2Te 3 (CBST) films grown on SrTiO 3 (1 1 1) substrates with and without a Te capping layer. We find that bothmore » the film and capping layer are single crystal and that the crystal quality of the film is independent of the presence of the capping layer, but that x-rays cause sublimation of the CBST film, which is prevented by the capping layer. Our findings show that the different transport properties of capped films cannot be attributed to a lower crystal quality but to a more subtle effect such as a different electronic structure at the interface with the capping layer. Our results on the crystal structure and atomic arrangements of the topological heterostructure will enable modelling the electronic structure and design of topological heterostructures.« less

Advantages of InGaN/GaN multiple quantum wells with two-step grown low temperature GaN cap layers

NASA Astrophysics Data System (ADS)

Zhu, Yadan; Lu, Taiping; Zhou, Xiaorun; Zhao, Guangzhou; Dong, Hailiang; Jia, Zhigang; Liu, Xuguang; Xu, Bingshe

2017-11-01

Two-step grown low temperature GaN cap layers (LT-cap) are employed to improve the optical and structural properties of InGaN/GaN multiple quantum wells (MQWs). The first LT-cap layer is grown in nitrogen atmosphere, while a small hydrogen flow is added to the carrier gas during the growth of the second LT-cap layer. High-resolution X-ray diffraction results indicate that the two-step growth method can improve the interface quality of MQWs. Room temperature photoluminescence (PL) tests show about two-fold enhancement in integrated PL intensity, only 25 meV blue-shift in peak energy and almost unchanged line width. On the basis of temperature-dependent PL characteristics analysis, it is concluded that the first and the second LT-cap layer play a different role during the growth of MQWs. The first LT-cap layer acts as a protective layer, which protects quantum well from serious indium loss and interface roughening resulting from the hydrogen over-etching. The hydrogen gas employed in the second LT-cap layer is in favor of reducing defect density and indium segregation. Consequently, interface/surface and optical properties are improved by adopting the two-step growth method.

Performance Analysis of GaN Capping Layer Thickness on GaN/AlGaN/GaN High Electron Mobility Transistors.

PubMed

Sharma, N; Periasamy, C; Chaturvedi, N

2018-07-01

In this paper, we present an investigation of the impact of GaN capping layer and AlGaN layer thickness on the two-dimensional (2D)-electron mobility and the carrier concentration which was formed close to the AlGaN/GaN buffer layer for Al0.25Ga0.75N/GaN and GaN/Al0.25Ga0.75N/GaN heterostructures deposited on sapphire substrates. The results of our analysis clearly indicate that expanding the GaN capping layer thickness from 1 nm to 100 nm prompts an increment in the electron concentration at hetero interface. As consequence of which drain current was additionally increments with GaN cap layer thicknesses, and eventually saturates at approximately 1.85 A/mm for capping layer thickness greater than 40 nm. Interestingly, for the same structure, the 2D-electron mobility, decrease monotonically with GaN capping layer thickness, and saturate at approximately 830 cm2/Vs for capping layer thickness greater than 50 nm. A device with a GaN cap layer didn't exhibit gate leakage current. Furthermore, it was observed that the carrier concentration was first decrease 1.03 × 1019/cm3 to 6.65 × 1018/cm3 with AlGaN Layer thickness from 5 to 10 nm and after that it increases with the AlGaN layer thickness from 10 to 30 nm. The same trend was followed for electric field distributions. Electron mobility decreases monotonically with AlGaN layer thickness. Highest electron mobility 1354 cm2/Vs were recorded for the AlGaN layer thickness of 5 nm. Results obtained are in good agreement with published experimental data.

Impact of laser-contaminant interaction on the performance of the protective capping layer of 1w high-reflection mirror coatings

DOE PAGES

Qiu, S. R.; Norton, M. A.; Raman, R. N.; ...

2015-10-02

In this paper, high dielectric constant multilayer coatings are commonly used on high-reflection mirrors for high-peak-power laser systems because of their high laser-damage resistance. However, surface contaminants often lead to damage upon laser exposure, thus limiting the mirror’s lifetime and performance. One plausible approach to improve the overall mirror resistance against laser damage, including that induced by laser-contaminant coupling, is to coat the multilayers with a thin protective capping (absentee) layer on top of the multilayer coatings. An understanding of the underlying mechanism by which laser-particle interaction leads to capping layer damage is important for the rational design and selectionmore » of capping materials of high-reflection multilayer coatings. In this paper, we examine the responses of two candidate capping layer materials, made of SiO 2 and Al 2O 3, over silica-hafnia multilayer coatings. These are exposed to a single oblique shot of a 1053 nm laser beam (fluence ~10 J/cm 2, pulse length 14 ns), in the presence of Ti particles on the surface. We find that the two capping layers show markedly different responses to the laser-particle interaction. The Al 2O 3 cap layer exhibits severe damage, with the capping layer becoming completely delaminated at the particle locations. The SiO 2 capping layer, on the other hand, is only mildly modified by a shallow depression. Combining the observations with optical modeling and thermal/mechanical calculations, we argue that a high-temperature thermal field from plasma generated by the laser-particle interaction above a critical fluence is responsible for the surface modification of each capping layer. The great difference in damage behavior is mainly attributed to the large disparity in the thermal expansion coefficient of the two capping materials, with that of Al 2O 3 layer being about 15 times greater than that of SiO 2.« less

Impact of laser-contaminant interaction on the performance of the protective capping layer of 1w high-reflection mirror coatings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qiu, S. R.; Norton, M. A.; Raman, R. N.

In this paper, high dielectric constant multilayer coatings are commonly used on high-reflection mirrors for high-peak-power laser systems because of their high laser-damage resistance. However, surface contaminants often lead to damage upon laser exposure, thus limiting the mirror’s lifetime and performance. One plausible approach to improve the overall mirror resistance against laser damage, including that induced by laser-contaminant coupling, is to coat the multilayers with a thin protective capping (absentee) layer on top of the multilayer coatings. An understanding of the underlying mechanism by which laser-particle interaction leads to capping layer damage is important for the rational design and selectionmore » of capping materials of high-reflection multilayer coatings. In this paper, we examine the responses of two candidate capping layer materials, made of SiO 2 and Al 2O 3, over silica-hafnia multilayer coatings. These are exposed to a single oblique shot of a 1053 nm laser beam (fluence ~10 J/cm 2, pulse length 14 ns), in the presence of Ti particles on the surface. We find that the two capping layers show markedly different responses to the laser-particle interaction. The Al 2O 3 cap layer exhibits severe damage, with the capping layer becoming completely delaminated at the particle locations. The SiO 2 capping layer, on the other hand, is only mildly modified by a shallow depression. Combining the observations with optical modeling and thermal/mechanical calculations, we argue that a high-temperature thermal field from plasma generated by the laser-particle interaction above a critical fluence is responsible for the surface modification of each capping layer. The great difference in damage behavior is mainly attributed to the large disparity in the thermal expansion coefficient of the two capping materials, with that of Al 2O 3 layer being about 15 times greater than that of SiO 2.« less

A DFT study on NEA GaN photocathode with an ultrathin n-type Si-doped GaN cap layer

NASA Astrophysics Data System (ADS)

Xia, Sihao; Liu, Lei; Kong, Yike; Diao, Yu

2016-10-01

Due to the drawbacks of conventional negative electron affinity (NEA) GaN photocathodes activated by Cs or Cs/O, a new-type NEA GaN photocathodes with heterojunction surface dispense with Cs activation are proposed. This structure can be obtained through the coverage of an ultrathin n-type Si-doped GaN cap layer on the p-type Mg-doped GaN emission layer. The influences of the cap layer on the photocathode are calculated using DFT. This study indicates that the n-type cap layer can promote the photoemission characteristics of GaN photocathode and demonstrates the probability of the preparation of a NEA GaN photocathode with an n-type cap layer.

Silicide formation process of Er films with Ta and TaN capping layers.

PubMed

Choi, Juyun; Choi, Seongheum; Kim, Jungwoo; Na, Sekwon; Lee, Hoo-Jeong; Lee, Seok-Hee; Kim, Hyoungsub

2013-12-11

The phase development and defect formation during the silicidation reaction of sputter-deposited Er films on Si with ∼20-nm-thick Ta and TaN capping layers were examined. TaN capping effectively prevented the oxygen incorporation from the annealing atmosphere, which resulted in complete conversion to the ErSi2-x phase. However, significant oxygen penetration through the Ta capping layer inhibited the ErSi2-x formation, and incurred the growth of several Er-Si-O phases, even consuming the ErSi2-x layer formed earlier. Both samples produced a number of small recessed defects at an early silicidation stage. However, large rectangular or square-shaped surface defects, which were either pitlike or pyramidal depending on the capping layer identity, were developed as the annealing temperature increased. The origin of different defect generation mechanisms was suggested based on the capping layer-dependent silicidation kinetics.

Theoretical study for heterojunction surface of NEA GaN photocathode dispensed with Cs activation

NASA Astrophysics Data System (ADS)

Xia, Sihao; Liu, Lei; Wang, Honggang; Wang, Meishan; Kong, Yike

2016-09-01

For the disadvantages of conventional negative electron affinity (NEA) GaN photocathodes activated by Cs or Cs/O, new-type NEA GaN photocathodes with heterojunction surface dispensed with Cs activation are investigated based on first-principle study with density functional theory. Through the growth of an ultrathin n-type GaN cap layer on p-type GaN emission layer, a p-n heterojunction is formed on the surface. According to the calculation results, it is found that Si atoms tend to replace Ga atoms to result in an n-type doped cap layer which contributes to the decreasing of work function. After the growth of n-type GaN cap layer, the atom structure near the p-type emission layer is changed while that away from the surface has no obvious variations. By analyzing the E-Mulliken charge distribution of emission surface with and without cap layer, it is found that the positive charge of Ga and Mg atoms in the emission layer decrease caused by the cap layer, while the negative charge of N atom increases. The conduction band moves downwards after the growth of cap layer. Si atom produces donor levels around the valence band maximum. The absorption coefficient of GaN emission layer decreases and the reflectivity increases caused by n-type GaN cap layer.

Cross-plane electrical and thermal transport in oxide metal/semiconductor superlattices

NASA Astrophysics Data System (ADS)

Jha, Pankaj

Perovskite oxides display a rich variety of electronic properties as metals, ferroelectrics, ferromagnetics, multiferroics, and thermoelectrics. Cross-plane electron filtering transport in metal/semiconductor superlattices provides a potential approach to increase the thermoelectric figure of merit (ZT). La0.67Sr0.33MnO3 (LSMO) and LaMnO3 (LMO) thin-film depositions were optimized using pulsed laser deposition (PLD) to achieve low resistivity constituent materials for LSMO/LMO superlattice heterostructures on (100)-strontium titanate (STO) substrates. X-ray diffraction and high-resolution reciprocal space mapping (RSM) indicate that the superlattices are epitaxial and pseudomorphic. Cross-plane devices were fabricated by etching cylindrical pillar structures in superlattices using inductively-coupled-plasma reactive-ion etching. The cross-plane electrical conductivity data for LSMO/LMO superlattices reveal an effective barrier height of 220 meV. The cross-plane LSMO/LMO superlattices showed a giant Seebeck coefficient of 2560 microV/K at 300K that increases to 16640 microV/K at 360K. The large Seebeck coefficient may arise due to hot electron and spin filtering as LSMO/LMO superlattice constituent materials exhibit spintronic properties where charges and spin current are intertwined and can generate a spin-Seebeck effect. The room temperature thermal conductivity achieved in low resistivity superlattices was 0.92 W/mK, which indicates that cross-plane phonon scattering at interfaces reduces the lattice contribution to the thermal conductivity. The giant contribution of spin-Seebeck, the large temperature dependence of the cross-plane power factor, and the low thermal conductivity in low resistance LSMO/LMO superlattices may offer opportunities to realize spin-magnetic thermoelectric devices, and suggests a direction for further investigations of the potential of LSMO/LMO oxide superlattices for thermoelectric devices.

Luminopsins integrate opto- and chemogenetics by using physical and biological light sources for opsin activation

PubMed Central

Berglund, Ken; Clissold, Kara; Li, Haofang E.; Wen, Lei; Park, Sung Young; Gleixner, Jan; Klein, Marguerita E.; Lu, Dongye; Barter, Joseph W.; Rossi, Mark A.; Augustine, George J.; Yin, Henry H.; Hochgeschwender, Ute

2016-01-01

Luminopsins are fusion proteins of luciferase and opsin that allow interrogation of neuronal circuits at different temporal and spatial resolutions by choosing either extrinsic physical or intrinsic biological light for its activation. Building on previous development of fusions of wild-type Gaussia luciferase with channelrhodopsin, here we expanded the utility of luminopsins by fusing bright Gaussia luciferase variants with either channelrhodopsin to excite neurons (luminescent opsin, LMO) or a proton pump to inhibit neurons (inhibitory LMO, iLMO). These improved LMOs could reliably activate or silence neurons in vitro and in vivo. Expression of the improved LMO in hippocampal circuits not only enabled mapping of synaptic activation of CA1 neurons with fine spatiotemporal resolution but also could drive rhythmic circuit excitation over a large spatiotemporal scale. Furthermore, virus-mediated expression of either LMO or iLMO in the substantia nigra in vivo produced not only the expected bidirectional control of single unit activity but also opposing effects on circling behavior in response to systemic injection of a luciferase substrate. Thus, although preserving the ability to be activated by external light sources, LMOs expand the use of optogenetics by making the same opsins accessible to noninvasive, chemogenetic control, thereby allowing the same probe to manipulate neuronal activity over a range of spatial and temporal scales. PMID:26733686

Simultaneous detection of three lily viruses using Triplex IC-RT-PCR.

PubMed

Zhang, Yubao; Wang, Yajun; Xie, Zhongkui; Yang, Guo; Guo, Zhihong; Wang, Le

2017-11-01

Viruses commonly infecting lily (Lilium spp.) include: Lily symptomless virus (LSV), Cucumber mosaic virus (CMV) and Lily mottle virus (LMoV). These viruses usually co-infect lilies causing severe economic losses in terms of quantity and quality of flower and bulb production around the world. Reliable and precise detection systems need to be developed for virus identification. We describe the development of a triplex immunocapture (IC) reverse transcription (RT) polymerase chain reaction (PCR) assay for the simultaneous detection of LSV, CMV and LMoV. The triplex IC-RT-PCR was compared with a quadruplex RT-PCR assay. Relative to the quadruplex RT-PCR, the specificity of the triplex IC-RT-PCR system for LSV, CMV and LMoV was 100% for field samples. The sensitivity of the triplex IC-RT-PCR system was 99.4%, 81.4% and 98.7% for LSV, CMV and LMoV, respectively. Agreement (κ) between the results obtained from the two tests was 0.968, 0.844 and 0.984 for LSV, CMV and LMoV, respectively. This is the first report of the simultaneous detection of LSV, CMV and LMoV in a triplex IC-RT-PCR assay. In particular we believe this convenient and reliable triplex IC-RT-PCR method could be used routinely for large-scale field surveys or crop health monitoring of lily. Copyright © 2017. Published by Elsevier B.V.

Integrated cistromic and expression analysis of amplified NKX2-1 in lung adenocarcinoma identifies LMO3 as a functional transcriptional target

PubMed Central

Watanabe, Hideo; Francis, Joshua M.; Woo, Michele S.; Etemad, Banafsheh; Lin, Wenchu; Fries, Daniel F.; Peng, Shouyong; Snyder, Eric L.; Tata, Purushothama Rao; Izzo, Francesca; Schinzel, Anna C.; Cho, Jeonghee; Hammerman, Peter S.; Verhaak, Roel G.; Hahn, William C.; Rajagopal, Jayaraj; Jacks, Tyler; Meyerson, Matthew

2013-01-01

The NKX2-1 transcription factor, a regulator of normal lung development, is the most significantly amplified gene in human lung adenocarcinoma. To study the transcriptional impact of NKX2-1 amplification, we generated an expression signature associated with NKX2-1 amplification in human lung adenocarcinoma and analyzed DNA-binding sites of NKX2-1 by genome-wide chromatin immunoprecipitation. Integration of these expression and cistromic analyses identified LMO3, itself encoding a transcription regulator, as a candidate direct transcriptional target of NKX2-1. Further cistromic and overexpression analyses indicated that NKX2-1 can cooperate with the forkhead box transcription factor FOXA1 to regulate LMO3 gene expression. RNAi analysis of NKX2-1-amplified cells compared with nonamplified cells demonstrated that LMO3 mediates cell survival downstream from NKX2-1. Our findings provide new insight into the transcriptional regulatory network of NKX2-1 and suggest that LMO3 is a transcriptional signal transducer in NKX2-1-amplified lung adenocarcinomas. PMID:23322301

Orientation-adjusted anomalous insulator-metal transition in NdNiO3/LaMnO3 bilayers

NASA Astrophysics Data System (ADS)

Pan, S. Y.; Shi, L.; Zhao, J. Y.; Zhou, S. M.; Xu, X. M.

2018-04-01

NdNiO3/LaMnO3 (NNO/LMO) bilayers were epitaxially grown on SrTiO3 (STO) substrates with different orientations by the polymer-assisted deposition technique. A well crystallization quality of the bilayers is confirmed by X-ray diffraction. Two consecutive transitions, an anomalous insulator-metal transition at ˜100 K followed by the typical metal-insulator transition at ˜171 K, are observed in the (001)-oriented NNO/LMO/STO bilayer. The anomalous insulator-metal transition temperature increases to 142 K for the (111)-oriented NNO/LMO/STO bilayer. Meanwhile, the magnetic properties of the NNO/LMO bilayers show an obvious difference with [100] and [111] orientations. Considering the different strain directions and the related oxygen octahedral distortion/rotation, it is suggested that the magnetic changes and the low-temperature anomalous insulator-metal transition in the NNO/LMO bilayers are attributed to the strong interlayer exchange coupling and charge transfer adjusted by the substrate orientation, which can be an effective technique to tune the properties of transition-metal oxide films.

A Low Viscosity Lunar Magma Ocean Forms a Stratified Anorthitic Flotation Crust With Mafic Poor and Rich Units

NASA Astrophysics Data System (ADS)

Dygert, Nick; Lin, Jung-Fu; Marshall, Edward W.; Kono, Yoshio; Gardner, James E.

2017-11-01

Much of the lunar crust is monomineralic, comprising >98% plagioclase. The prevailing model argues the crust accumulated as plagioclase floated to the surface of a solidifying lunar magma ocean (LMO). Whether >98% pure anorthosites can form in a flotation scenario is debated. An important determinant of the efficiency of plagioclase fractionation is the viscosity of the LMO liquid, which was unconstrained. Here we present results from new experiments conducted on a late LMO-relevant ferrobasaltic melt. The liquid has an exceptionally low viscosity of 0.22-0.19+0.11 to 1.45-0.82+0.46 Pa s at experimental conditions (1,300-1,600°C; 0.1-4.4 GPa) and can be modeled by an Arrhenius relation. Extrapolating to LMO-relevant temperatures, our analysis suggests a low viscosity LMO would form a stratified flotation crust, with the oldest units containing a mafic component and with very pure younger units. Old, impure crust may have been buried by lower crustal diapirs of pure anorthosite in a serial magmatism scenario.

ACCURATE: Greenhouse Gas Profiles Retrieval from Combined IR-Laser and Microwave Occultation Measurements

NASA Astrophysics Data System (ADS)

Proschek, Veronika; Kirchengast, Gottfried; Schweitzer, Susanne; Fritzer, Johannes

2010-05-01

The new climate satellite concept ACCURATE (Atmospheric Climate and Chemistry in the UTLS Region And climate Trends Explorer) enables simultaneous measurement of profiles of greenhouse gases, isotopes, wind and thermodynamic variables from Low Earth Orbit (LEO) satellites. The measurement principle applied is a combination of the novel LEO-LEO infrared laser occultation (LIO) technique and the already better studied LEO-LEO microwave occultation (LMO) technique. Resulting occultation events are evenly distributed around the world, have high vertical resolution and accuracy and are stable over long time periods. The LIO uses near-monochromatic signals in the short-wave infrared range (~2-2.5 μm for ACCURATE). These signals are absorbed by various trace species in the Earth's atmosphere. Profiles of the concentration of the absorbing species can be derived from signal transmission measurements. Accurately known temperature, pressure and humidity profiles derived from simultaneously measured LMO signals are essential pre-information for the retrieval of the trace species profiles. These LMO signals lie in the microwave band region from 17-23 GHz and, optionally, 178-195 GHz. The current ACCURATE mission design is arranged for the measurement of six greenhouse gases (GHG) (H2O, CO2, CH4, N2O, O3, CO) and four isotopes (13CO2, C18OO, HDO, H218O), with focus on the upper troposphere/lower stratosphere region (UTLS, 5-35 km). Wind speed in line-of-sight can be derived from a line-symmetric transmission difference which is caused by wind-induced Doppler shift. By-products are information on cloud layering, aerosol extinction, and scintillation strength. We introduce the methodology to retrieve GHG profiles from quasi-realistic forward-simulated intensities of LIO signals and thermodynamic profiles retrieved in a preceding step from LMO signals. Key of the retrieval methodology is the differencing of two LIO transmission signals, one being GHG sensitive on a target absorption line and one being a close-by reference outside of any absorption lines. The reference signal is used to remove atmospheric broadband" effects by this differential absorption" approach. Refractivity and impact parameter of the LIO signals, needed for the retrieval, can be computed from the LMO-derived thermodynamic profiles. An Abel Transform converts the differential LIO log-transmission profile to the absorption coefficient. Based on the absorption coefficient and the absorption cross section of the GHG under investigation, that can as well be computed from the LMO-derived profiles, the number density profile or volume mixing ratio of the desired GHG can be finally derived. When using several LIO signals, best sensitive to the same GHG at different heights, a joint optimal GHG profile can be constructed by combining the individual profiles in an inverse-variance-weighted manner (practically used for H2O, obtained from 3-4 signals, and for CO2, obtained from 2 isotope signals). The thermodynamic parameters (temperature, pressure and humidity) derived from LMO as basis for the LIO retrieval are found to be accurate to better than 0.5 K for temperature, 0.2% for pressure, and 10% for humidity. The accuracy of retrieved trace species profiles is found better than 1% to 4% for single profiles in the UTLS region (outside clouds which block infrared) and the profiles are essentially unbiased (biases

Effect of NiFeCr seed and capping layers on exchange bias and planar Hall voltage response of NiFe/Au/IrMn trilayer structures

NASA Astrophysics Data System (ADS)

Talantsev, Artem; Elzwawy, Amir; Kim, CheolGi

2018-05-01

Thin films and cross junctions, based on NiFe/Au/IrMn structures, were grown on Ta and NiFeCr seed layers by magnetron sputtering. The effects of substitution of Ta with NiFeCr in seed and capping layers on an exchange bias field are studied. A threefold improvement of the exchange bias value in the structures, grown with NiFeCr seed and capping layers, is demonstrated. The reasons for this effect are discussed. Formation of clusters in the NiFeCr capping layer is proved by atomic force microscopy technique. Ta replacement on NiFeCr in the capping layer results in the enhancement of magnetoresistive response and a reduction of noise.

Synchrotron X-ray nano computed tomography based simulation of stress evolution in LiMn 2O 4 electrodes

DOE PAGES

Ghorbani Kashkooli, Ali; Foreman, Evan; Farhad, Siamak; ...

2017-07-18

Here in this study, synchrotron X-ray nano-computed tomography at Advanced Photon Source in Argonne National Laboratory has been employed to reconstruct real 3D active particle morphology of LiMn 2O 4 (LMO) commonly used in lithium-ion batteries (LIBs). For the first time, carbon-doped binder domain (CBD) has been included in the electrode structure as a 108 nm thick uniform layer using image processing technique. With this unique model, stress generated inside four LMO particles with a uniform layer of CBD has been simulated, demonstrating its strong dependence on local morphology (surface concavity and convexity), and the mechanical properties of CBD suchmore » as Young’s modulus. Specifically, high levels of stress have been found in vicinity of particle’s center or near surface concave regions, however much lower than the material failure limits even after discharging at the rate as high as 5C. On the other hand, the stress inside CBD has reached its mechanical limits when discharged at 5C, suggesting that it can potentially lead to failure by plastic deformation. The findings in this study highlight the importance of modeling LIB active particles with CBD and its appropriate compositional design and development to prevent the loss of electrical connectivity of the active particles from the percolated solid network and power losses due to CBD failure.« less

Synchrotron X-ray nano computed tomography based simulation of stress evolution in LiMn 2O 4 electrodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ghorbani Kashkooli, Ali; Foreman, Evan; Farhad, Siamak

Here in this study, synchrotron X-ray nano-computed tomography at Advanced Photon Source in Argonne National Laboratory has been employed to reconstruct real 3D active particle morphology of LiMn 2O 4 (LMO) commonly used in lithium-ion batteries (LIBs). For the first time, carbon-doped binder domain (CBD) has been included in the electrode structure as a 108 nm thick uniform layer using image processing technique. With this unique model, stress generated inside four LMO particles with a uniform layer of CBD has been simulated, demonstrating its strong dependence on local morphology (surface concavity and convexity), and the mechanical properties of CBD suchmore » as Young’s modulus. Specifically, high levels of stress have been found in vicinity of particle’s center or near surface concave regions, however much lower than the material failure limits even after discharging at the rate as high as 5C. On the other hand, the stress inside CBD has reached its mechanical limits when discharged at 5C, suggesting that it can potentially lead to failure by plastic deformation. The findings in this study highlight the importance of modeling LIB active particles with CBD and its appropriate compositional design and development to prevent the loss of electrical connectivity of the active particles from the percolated solid network and power losses due to CBD failure.« less

Genetic predisposition to neuroblastoma mediated by a LMO1 super-enhancer polymorphism | Office of Cancer Genomics

Cancer.gov

Neuroblastoma is a paediatric malignancy that typically arises in early childhood, and is derived from the developing sympathetic nervous system. Clinical phenotypes range from localized tumours with excellent outcomes to widely metastatic disease in which long-term survival is approximately 40% despite intensive therapy. A previous genome-wide association study identified common polymorphisms at the LMO1 gene locus that are highly associated with neuroblastoma susceptibility and oncogenic addiction to LMO1 in the tumour cells.

The influence of cycling temperature and cycling rate on the phase specific degradation of a positive electrode in lithium ion batteries: A post mortem analysis

NASA Astrophysics Data System (ADS)

Darma, Mariyam Susana Dewi; Lang, Michael; Kleiner, Karin; Mereacre, Liuda; Liebau, Verena; Fauth, Francois; Bergfeldt, Thomas; Ehrenberg, Helmut

2016-09-01

The influence of cycling temperatures and cycling rates on the cycling stability of the positive electrode (cathode) of commercial batteries are investigated. The cathode is a mixture of LiMn2O4 (LMO), LiNi0.5Co0.2Mn0.3O2 (NCM) and LiNi0.8Co0.15Al0.05O2 (NCA). It is found that increasing the cycling temperature from 25 °C to 40 °C is detrimental to the long term cycling stability of the cathode. Contrastingly, the improved cycling stability is observed for the cathodes cycled at higher charge/discharge rate (2C/3C instead of 1C/2C). The microstructure analysis by X-ray powder diffraction reveals that a significant capacity fading and an increased overvoltage is observed for NCM and NCA in all the fatigued cathodes. After high number of cycling (above 1500 cycles), NCM becomes partially inactive. In contrast to NCM and NCA, LMO shows a good cycling stability at 25 °C. A pronounced degradation of LMO is only observed for the fatigued cathodes cycled at 40 °C. The huge capacity losses of NCM and NCA are most likely because the blended cathodes were cycled up to 4.12 V vs. the graphite anode during the cycle-life test (corresponds to 4.16 V vs. Li+/Li); which is beyond the stability limit of the layered oxides below 4.05 V vs. Li+/Li.

Designing Next Generation Rechargeable Battery Materials from First-Principles

NASA Astrophysics Data System (ADS)

Kim, Soo

Technology has advanced rapidly, especially in the twenty-first century, influencing our day-to-day life on unprecedented levels. Most such advances in technology are closely linked to, and often driven by, the discovery and design of new materials. It follows that the discovery of new materials can not only improve existing technologies but also lead to revolutionary ones. In particular, there is a growing need to develop new energy materials that are reliable, clean, and affordable for emerging applications such as portable electronics, electric vehicles, and power grid systems. Many researchers have been actively searching for more cost-effective and clean electrode materials for lithium-ion batteries (LIBs) during the last few decades. These new electrode materials are also required to achieve higher electrochemical performance, compared to the already commercialized electrodes. Unfortunately, discovering the next sustainable energy materials based on a traditional 'trial-and-error' method via experiment would be extremely slow and difficult. In the last two decades, computational compilations of battery material properties such as voltage, diffusivity, and phase stability against irreversible phase transformation(s) using first-principles density functional theory (DFT) calculations have helped researchers to understand the underlying mechanism in many oxide materials that are used as LIB electrodes. Here, we have examined the (001) and (111) surface structures of LiMn2O4 (LMO) spinel cathode materials using DFT calculations within the generalized gradient approximation (GGA) + U approach. Our theoretical results explain the observation of a wide spectrum of polyhedral shapes between (001)- and (111)-dominated LMO particles in experiments, which can be described by the narrow range of surface energies and their sensitivity to synthesis conditions. We further show that single-layer graphene coatings help suppress manganese dissolution in LMO by chemically interacting with Mn3+ at the (001) LMO surface, promoting an oxidation state change to Mn4+. In addition, we find that graphene defects also react with H2O and generated HF, protecting the active cathode materials from the attack of HF generated in the electrolyte during cycling. The carbonyl and epoxy functional groups in graphene oxide (GO) serve as a physical barrier to mitigate Mn ion dissolution into the liquid electrolyte, stabilizing the overall cell cycling performance. Next, we examine the occurrence of low- and high-temperature LiCoO2 structures and their observed voltage profiles in order to understand the complex structural and electrochemical behaviors. Moreover, a structural search is conducted to identify a new over-lithiated spinel oxide composition, i.e., Fd3¯m LiNi0.8125Co0.1875O2, which may have potential for exploitation in structurally-integrated, 'layered-spinel' cathode system. We have further investigated the structural and electrochemical properties of 'layered-layered-spinel' xLi 2MnO3˙yLiNi0.5Co0.2 Mn0.3O2˙zLiNi0.5Mn 1.5O4 cathode materials using both experiment and theory. Lastly, the idea of a multi-faceted high-throughput (HT) screening approach has been performed within the Open Quantum Materials Database (OQMD) framework to discover possible Li-rich Li2MIO3-Li 2MIIO3 pair combinations (MI,II = elements from the periodic table) that can offer better structural stability, favorable metal-mixing behavior, coherent interfaces, and high energy. Our approach involving computational design of novel materials and systems will accelerate the development of new sustainable energy solutions for meeting global demands.

Requirement for Lmo4 in the Vestibular Morphogenesis of Mouse Inner Ear

PubMed Central

Deng, Min; Pan, Ling; Xie, Xiaoling; Gan, Lin

2009-01-01

During development, compartmentalization of an early embryonic structure produces blocks of cells with distinct properties and developmental potentials. The auditory and vestibular components of vertebrate inner ears are derived from defined compartments within the otocyst during embryogenesis. The vestibular apparatus, including three semicircular canals, saccule, utricle, and their associated sensory organs, detects angular and linear acceleration of the head and relays the information through vestibular neurons to vestibular nuclei in the brainstem. How the early developmental events manifest vestibular structures at the molecular level is largely unknown. Here, we show that LMO4, a LIM-domain-only transcriptional regulator, is required for the formation of semicircular canals and their associated sensory cristae. Targeted disruption of Lmo4 resulted in the dysmorphogenesis of the vestibule and in the absence of three semicircular canals, anterior and posterior cristae. In Lmo4-null otocysts, canal outpouches failed to form and cell proliferation was reduced in the dorsolateral region. Expression analysis of the known otic markers showed that Lmo4 is essential for the normal expression of Bmp4, Fgf10, Msx1, Isl1, Gata3, and Dlx5 in the dorsolateral domain of the otocyst, whereas the initial compartmentalization of the otocyst remains unaffected. Our results demonstrate that Lmo4 controls the development of the dorsolateral otocyst into semicircular canals and cristae through two distinct mechanisms: regulating the expression of otic specific genes and stimulating the proliferation of the dorsolateral part of the otocyst. PMID:19913004

Controlling contamination in Mo/Si multilayer mirrors by Si surface capping modifications

NASA Astrophysics Data System (ADS)

Malinowski, Michael E.; Steinhaus, Chip; Clift, W. Miles; Klebanoff, Leonard E.; Mrowka, Stanley; Soufli, Regina

2002-07-01

The performance of Mo/Si multilayer mirrors (MLMs) used to reflect UV (EUV) radiation in an EUV + hydrocarbon (NC) vapor environment can be improved by optimizing the silicon capping layer thickness on the MLM in order to minimize the initial buildup of carbon on MLMs. Carbon buildup is undesirable since it can absorb EUV radiation and reduce MLM reflectivity. A set of Mo/Si MLMs deposited on Si wafers was fabricated such that each MLM had a different Si capping layer thickness ranging form 2 nm to 7 nm. Samples from each MLM wafer were exposed to a combination of EUV light + (HC) vapors at the Advanced Light Source (ALS) synchrotron in order to determine if the Si capping layer thickness affected the carbon buildup on the MLMs. It was found that the capping layer thickness had a major influence on this 'carbonizing' tendency, with the 3 nm layer thickness providing the best initial resistance to carbonizing and accompanying EUV reflectivity loss in the MLM. The Si capping layer thickness deposited on a typical EUV optic is 4.3 nm. Measurements of the absolute reflectivities performed on the Calibration and Standards beamline at the ALS indicated the EUV reflectivity of the 3 nm-capped MLM was actually slightly higher than that of the normal, 4 nm Si-capped sample. These results show that he use of a 3 nm capping layer represents an improvement over the 4 nm layer since the 3 nm has both a higher absolute reflectivity and better initial resistance to carbon buildup. The results also support the general concept of minimizing the electric field intensity at the MLM surface to minimize photoelectron production and, correspondingly, carbon buildup in a EUV + HC vapor environment.

A Low Viscosity Lunar Magma Ocean Forms a Stratified Anorthitic Flotation Crust With Mafic Poor and Rich Units: Lunar Magma Ocean Viscosity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dygert, Nick; Lin, Jung-Fu; Marshall, Edward W.

Much of the lunar crust is monomineralic, comprising >98% plagioclase. The prevailing model argues the crust accumulated as plagioclase floated to the surface of a solidifying lunar magma ocean (LMO). Whether >98% pure anorthosites can form in a flotation scenario is debated. An important determinant of the efficiency of plagioclase fractionation is the viscosity of the LMO liquid, which was unconstrained. Here we present results from new experiments conducted on a late LMO-relevant ferrobasaltic melt. The liquid has an exceptionally low viscosity of 0.22more » $$+0.11\\atop{-0.19}$$to 1.45 $$+0.46\\atop{-0.82}$$ Pa s at experimental conditions (1,300–1,600°C; 0.1–4.4 GPa) and can be modeled by an Arrhenius relation. Extrapolating to LMO-relevant temperatures, our analysis suggests a low viscosity LMO would form a stratified flotation crust, with the oldest units containing a mafic component and with very pure younger units. Old, impure crust may have been buried by lower crustal diapirs of pure anorthosite in a serial magmatism scenario.« less

Origin of interfacial perpendicular magnetic anisotropy in MgO/CoFe/metallic capping layer structures

NASA Astrophysics Data System (ADS)

Peng, Shouzhong; Wang, Mengxing; Yang, Hongxin; Zeng, Lang; Nan, Jiang; Zhou, Jiaqi; Zhang, Youguang; Hallal, Ali; Chshiev, Mairbek; Wang, Kang L.; Zhang, Qianfan; Zhao, Weisheng

2015-12-01

Spin-transfer-torque magnetic random access memory (STT-MRAM) attracts extensive attentions due to its non-volatility, high density and low power consumption. The core device in STT-MRAM is CoFeB/MgO-based magnetic tunnel junction (MTJ), which possesses a high tunnel magnetoresistance ratio as well as a large value of perpendicular magnetic anisotropy (PMA). It has been experimentally proven that a capping layer coating on CoFeB layer is essential to obtain a strong PMA. However, the physical mechanism of such effect remains unclear. In this paper, we investigate the origin of the PMA in MgO/CoFe/metallic capping layer structures by using a first-principles computation scheme. The trend of PMA variation with different capping materials agrees well with experimental results. We find that interfacial PMA in the three-layer structures comes from both the MgO/CoFe and CoFe/capping layer interfaces, which can be analyzed separately. Furthermore, the PMAs in the CoFe/capping layer interfaces are analyzed through resolving the magnetic anisotropy energy by layer and orbital. The variation of PMA with different capping materials is attributed to the different hybridizations of both d and p orbitals via spin-orbit coupling. This work can significantly benefit the research and development of nanoscale STT-MRAM.

Origin of interfacial perpendicular magnetic anisotropy in MgO/CoFe/metallic capping layer structures.

PubMed

Peng, Shouzhong; Wang, Mengxing; Yang, Hongxin; Zeng, Lang; Nan, Jiang; Zhou, Jiaqi; Zhang, Youguang; Hallal, Ali; Chshiev, Mairbek; Wang, Kang L; Zhang, Qianfan; Zhao, Weisheng

2015-12-11

Spin-transfer-torque magnetic random access memory (STT-MRAM) attracts extensive attentions due to its non-volatility, high density and low power consumption. The core device in STT-MRAM is CoFeB/MgO-based magnetic tunnel junction (MTJ), which possesses a high tunnel magnetoresistance ratio as well as a large value of perpendicular magnetic anisotropy (PMA). It has been experimentally proven that a capping layer coating on CoFeB layer is essential to obtain a strong PMA. However, the physical mechanism of such effect remains unclear. In this paper, we investigate the origin of the PMA in MgO/CoFe/metallic capping layer structures by using a first-principles computation scheme. The trend of PMA variation with different capping materials agrees well with experimental results. We find that interfacial PMA in the three-layer structures comes from both the MgO/CoFe and CoFe/capping layer interfaces, which can be analyzed separately. Furthermore, the PMAs in the CoFe/capping layer interfaces are analyzed through resolving the magnetic anisotropy energy by layer and orbital. The variation of PMA with different capping materials is attributed to the different hybridizations of both d and p orbitals via spin-orbit coupling. This work can significantly benefit the research and development of nanoscale STT-MRAM.

South Polar Layers

NASA Image and Video Library

2016-08-25

Southern hemisphere spring has arrived at the south polar cap. The ice layers that make up the cap are easily seen in this image from NASA 2001 Mars Odyssey spacecraft. Southern hemisphere spring has arrived at the south polar cap. The ice layers that make up the cap are easily seen in this VIS image. Orbit Number: 64531 Latitude: -86.6334 Longitude: 97.7916 Instrument: VIS Captured: 2016-07-01 06:55 http://photojournal.jpl.nasa.gov/catalog/PIA20972

Combined Biology and Bioinformatics Approaches to Breast Cancer

DTIC Science & Technology

2006-04-01

In these experiments, LMO4 interacted with the MH1 and linker domains of Smad3 ; no interaction was found with the MH2 domain (Figure 4b). Figure 2...transcriptional response to TGFb by interacting with Smad proteins, and that both the MH1 and linker domains of Smad3 participate in the interaction. LMO4 can...LMO4 interacts with the MH1 and linker regions of Smad proteins. (a) Full-length, 35S-labeled Smad2, Smad3 , Smad4, Smad5, and Smad8 were incubated with

Combined Biology and Bioinformatics Approaches to Breast Cancer

DTIC Science & Technology

2005-04-01

interacted with the MH 1 and linker domains in both Smad3 and Smad4; no interaction was found with the MH2 domain (Fig. 7C). These data suggest that LMO4...LMO4 interacts with these Smads. GST protein-protein interaction assays showed that LMO4 binds to the MH1 and linker domain of Smad 1, Smad3 and Smad4...by facilitating the nuclear translocation and DNA-binding of a complex composed of an R-Smad (Smad2 and/or Smad3 ) and the co-Smad, Smad4 (10). To

Effect of heat treatment on interface driven magnetic properties of CoFe films

NASA Astrophysics Data System (ADS)

Singh, Akhilesh Kr.; Hsu, Jen-Hwa

2017-06-01

We report systematic studies on non-magnetic Ta underlayer and cap layer driven microstructural and magnetic properties at a wide temperature range for CoFe films. All the films were grown at room temperature and post annealed at different annealing temperatures (TA = 200 °C, 250 °C, 300 °C, 350 °C, 400 °C and 450 °C). The in-plane magnetic hysteresis (M-H) loops of 10 nm thick CoFe single layer films, grown directly on thermally oxidized Si substrate, exhibit anisotropic nature for TA above 250 °C. However, the CoFe (10 nm) films grown on the 5 nm thick Ta underlayer show reduced anisotropy. Moreover, with underlayer and cap layers (2 nm) the anisotropy is disappeared. The in-plane coercivity (HC) shows a strong variation with TA, underlayer and cap layers. HC increases significantly with Ta underlayer and cap layers. The out of plane M-H loops exhibit increase in the remanence magnetization and squareness with both Ta underlayer and cap layers due to transition of in-plane magnetization component to the out of plane direction. The atomic force microscopic observations revealed that grain/particle size and shape depend strongly on TA and Ta layers. Moreover, a large reduction in the surface roughness is observed with the Ta cap layer. The magnetic domain patterns depend on the TA, and Ta layers. However, for Ta/CoFe/Ta films no clear domains were observed for all the TA. Hence, the Ta cap layers not only protect the CoFe magnetic layer against the heat treatment, but also show a smooth surface at a wide temperature range. These results could be discussed on the basis of random anisotropy model, TA, underlayer and cap layers driven microstructure and magnetization orientation of the CoFe films.

Cyclic di-GMP-dependent Signaling Pathways in the Pathogenic Firmicute Listeria monocytogenes

PubMed Central

Chen, Li-Hong; Köseoğlu, Volkan K.; Güvener, Zehra T.; Myers-Morales, Tanya; Reed, Joseph M.; D'Orazio, Sarah E. F.; Miller, Kurt W.; Gomelsky, Mark

2014-01-01

We characterized key components and major targets of the c-di-GMP signaling pathways in the foodborne pathogen Listeria monocytogenes, identified a new c-di-GMP-inducible exopolysaccharide responsible for motility inhibition, cell aggregation, and enhanced tolerance to disinfectants and desiccation, and provided first insights into the role of c-di-GMP signaling in listerial virulence. Genome-wide genetic and biochemical analyses of c-di-GMP signaling pathways revealed that L. monocytogenes has three GGDEF domain proteins, DgcA (Lmo1911), DgcB (Lmo1912) and DgcC (Lmo2174), that possess diguanylate cyclase activity, and three EAL domain proteins, PdeB (Lmo0131), PdeC (Lmo1914) and PdeD (Lmo0111), that possess c-di-GMP phosphodiesterase activity. Deletion of all phosphodiesterase genes (ΔpdeB/C/D) or expression of a heterologous diguanylate cyclase stimulated production of a previously unknown exopolysaccharide. The synthesis of this exopolysaccharide was attributed to the pssA-E (lmo0527-0531) gene cluster. The last gene of the cluster encodes the fourth listerial GGDEF domain protein, PssE, that functions as an I-site c-di-GMP receptor essential for exopolysaccharide synthesis. The c-di-GMP-inducible exopolysaccharide causes cell aggregation in minimal medium and impairs bacterial migration in semi-solid agar, however, it does not promote biofilm formation on abiotic surfaces. The exopolysaccharide also greatly enhances bacterial tolerance to commonly used disinfectants as well as desiccation, which may contribute to survival of L. monocytogenes on contaminated food products and in food-processing facilities. The exopolysaccharide and another, as yet unknown c-di-GMP-dependent target, drastically decrease listerial invasiveness in enterocytes in vitro, and lower pathogen load in the liver and gallbladder of mice infected via an oral route, which suggests that elevated c-di-GMP levels play an overall negative role in listerial virulence. PMID:25101646

Ruthenium (Ru) peeling and predicting robustness of the capping layer using finite element method (FEM) modeling

NASA Astrophysics Data System (ADS)

Jang, Il-Yong; John, Arun; Goodwin, Frank; Lee, Su-Young; Kim, Byung-Gook; Kim, Seong-Sue; Jeon, Chan-Uk; Kim, Jae Hyung; Jang, Yong Hoon

2014-07-01

Ruthenium (Ru) film used as capping layer in extreme ultraviolet (EUV) mask peeled off after annealing and in-situ UV (IUV) cleaning. We investigated Ru peeling and found out that the mechanical stress caused by the formation of Si oxide due to the penetration of oxygen atoms from ambient or cleaning media to top-Si of ML is the root cause for the problem. To support our experimental results, we developed a numerical model of finite element method (FEM) using commercial software (ABAQUS™) to calculate the stress and displacement forced on the capping layer. By using this model, we could observe that the displacement agrees well with the actual results measured from the transmission electron microscopy (TEM) image. Using the ion beam deposition (IBD) tool at SEMATECH, we developed four new types of alternative capping materials (RuA, RuB, B4C, B4C-buffered Ru). The durability of each new alternative capping layer observed by experiment was better than that of conventional Ru. The stress and displacement calculated from each new alternative capping layer, using modeling, also agreed well with the experimental results. A new EUV mask structure is proposed, inserting a layer of B4C (B4C-buffered Ru) at the interface between the capping layer (Ru) and the top-Si layer. The modeling results showed that the maximum displacement and bending stress observed from the B4C-buffered Ru are significantly lower than that of single capping layer cases. The durability investigated from the experiment also showed that the B4C-buffered structure is at least 3X stronger than that of conventional Ru.

Enhanced annealing stability and perpendicular magnetic anisotropy in perpendicular magnetic tunnel junctions using W layer

NASA Astrophysics Data System (ADS)

Chatterjee, Jyotirmoy; Sousa, Ricardo C.; Perrissin, Nicolas; Auffret, Stéphane; Ducruet, Clarisse; Dieny, Bernard

2017-05-01

The magnetic properties of the perpendicular storage electrode (buffer/MgO/FeCoB/Cap) were studied as a function of annealing temperature by replacing Ta with W and W/Ta cap layers with variable thicknesses. W in the cap boosts up the annealing stability and increases the effective perpendicular anisotropy by 30% compared to the Ta cap. Correspondingly, an increase in the FeCoB critical thickness characterizing the transition from perpendicular to in-plane anisotropy was observed. Thicker W layer in the W(t)/Ta 1 nm cap layer makes the storage electrode highly robust against annealing up to 570 °C. The stiffening of the overall stack resulting from the W insertion due to its very high melting temperature seems to be the key mechanism behind the extremely high thermal robustness. The Gilbert damping constant of FeCoB with the W/Ta cap was found to be lower when compared with the Ta cap and stable with annealing. The evolution of the magnetic properties of bottom pinned perpendicular magnetic tunnel junctions (p-MTJ) stack with the W2/Ta1 nm cap layer shows back-end-of-line compatibility with increasing tunnel magnetoresistance up to the annealing temperature of 425 °C. The pMTJ thermal budget is limited by the synthetic antiferromagnetic hard layer which is stable up to 425 °C annealing temperature while the storage layer is stable up to 455 °C.

Selective layer disordering in III-nitrides with a capping layer

DOEpatents

Wierer, Jr., Jonathan J.; Allerman, Andrew A.

2016-06-14

Selective layer disordering in a doped III-nitride superlattice can be achieved by depositing a dielectric capping layer on a portion of the surface of the superlattice and annealing the superlattice to induce disorder of the layer interfaces under the uncapped portion and suppress disorder of the interfaces under the capped portion. The method can be used to create devices, such as optical waveguides, light-emitting diodes, photodetectors, solar cells, modulators, laser, and amplifiers.

The Lunar Magma Ocean (LMO) Paradigm Versus the Realities of Lunar Anorthosites

NASA Astrophysics Data System (ADS)

Treiman, A. H.; Gross, J.

2018-05-01

The paradigm of the Lunar Magma Ocean (LMO) is inconsistent with much chemical and compositional data on lunar anorthosites. The paradigm of serial anorthosite diapirism is more consistent, though not a panacea.

Effect of capping layer on interlayer coupling in synthetic spin valves

NASA Astrophysics Data System (ADS)

Li, Kebin; Qiu, Jinjun; Han, Guchang; Guo, Zaibing; Zheng, Yuankai; Wu, Yihong; Li, Jinshan

2005-01-01

The magnetic and transport properties of high quality synthetic spin-valves with the structure of Ta/NiFe/IrMn/CoFe/Ru/CoFe/NOL/CoFe/Cu/CoFe/CL were studied by using magnetoresistance measurements. Here Ti, Hf, and Al are used as the capping layer. It is found that both the thickness and materials properties of the capping layers can affect the interlayer coupling field. The interlayer coupling field oscillates weakly with respect to the thickness of the Ti and Hf capping layers. Extremely strong ferromagnetic coupling has been observed when the thickness of the Al capping layer is in a certain range where resonant exchange coupling takes place. The strength of the interlayer coupling is inversely proportional to the square of the thickness of the spacer. It is a typical characteristic of quantum size effect.

Thermal stability in the blended lithium manganese oxide – Lithium nickel cobalt manganese oxide cathode materials: An in situ time-resolved X-Ray diffraction and mass spectroscopy study

DOE PAGES

Hu, Enyuan; Bak, Seong Min; Senanayake, Sanjaya D.; ...

2015-03-01

Thermal stabilities of a series of blended LiMn 2O 4(LMO)-LiNi 1/3Co 1/3Mn 1/3O 2 (NCM) cathode materials with different weight ratios were studied by in situ time-resolved X-ray diffraction (XRD) combined with mass spectroscopy in the temperature range of 25°C-580°C under helium atmosphere. Upon heating, the electrochemically delithiated LMO changed into Mn 3O 4 phase at around 250°C. Formation of MnO with rocksalt structure started at 520°C. This observation is in contrast to the previous report for chemically delithiate LMO in air, in which a process of λ-MnO 2 transforming to β-MnO 2 was observed. Oxygen peak was not observedmore » in all cases, presumably as a result of either consumption by the carbon or detection limit. CO 2 profile correlates well with the phase transition and indirectly suggests the oxygen release of the cathode. Introducing NCM into LMO has two effects: first, it makes the high temperature rock-salt phase formation more complicated with more peaks in CO 2 profile due to different MO (M = Ni, Mn, Co) phases; secondly, the onset temperature of CO 2 release is lowered, implying lowered oxygen release temperature. Upon heating, XRD patterns indicate the NCM part reacts first, followed by the LMO part. This confirms the better thermal stability of LMO over NCM.« less

Method of forming an HTS article

DOEpatents

Bhattacharya, Raghu N.; Zhang, Xun; Selvamanickam, Venkat

2014-08-19

A method of forming a superconducting article includes providing a substrate tape, forming a superconducting layer overlying the substrate tape, and depositing a capping layer overlying the superconducting layer. The capping layer includes a noble metal and has a thickness not greater than about 1.0 micron. The method further includes electrodepositing a stabilizer layer overlying the capping layer using a solution that is non-reactive to the superconducting layer. The superconducting layer has an as-formed critical current I.sub.C(AF) and a post-stabilized critical current I.sub.C(PS). The I.sub.C(PS) is at least about 95% of the I.sub.C(AF).

Enhanced electrochemical performance of LiMn2O4 by constructing a stable Mn2+-rich interface

NASA Astrophysics Data System (ADS)

Lu, Zhongpei; Lu, Xiaojun; Ding, Jingjing; Zhou, Ting; Ge, Tao; Yang, Gang; Yin, Fan; Wu, Mingfang

2017-12-01

Spinel LiMn2O4 has drawn continuous attentions due to its low cost, good electrochemical performance, environmental friendliness and natural abundant resources. In view of its severe capacity fading, some types of manganese-based compounds with different Mn oxidation states are selected to protect bare LiMn2O4 by constructing a stable coating layer. In this work, LiMn2O4@LiMnPO4 composite, spherical LiMn2O4 (LMO) as core and Mn2+-rich phase of LiMnPO4 (LMP) as shell, is designed and synthesized. Two composites of LiMn2O4 particles coated with 3 wt% and 10 wt% LiMnPO4 have been compared studied. After 100 cycles at 0.5C rate, the two samples deliver capacity retentions of 96.63% and 93.23% of their initial capacities. Moreover, LMO coated by 3 wt% LiMnPO4 delivers 100.3 mAh g-1 after 200 cycles at 10C rate and 76.3 mAh g-1 after 1000 cycles at 20C rate, much higher than bare LiMn2O4 with 90 mAh g-1 and 45.8 mAh g-1, respectively. This core-shell structure with Mn2+-rich phase as a coating layer effectively enhance the material's cycling performance and rate capacity by reducing the contact of LiMn2O4 with electrolyte.

Graphene-Armored Aluminum Foil with Enhanced Anticorrosion Performance as Current Collectors for Lithium-Ion Battery.

PubMed

Wang, Mingzhan; Tang, Miao; Chen, Shulin; Ci, Haina; Wang, Kexin; Shi, Liurong; Lin, Li; Ren, Huaying; Shan, Jingyuan; Gao, Peng; Liu, Zhongfan; Peng, Hailin

2017-12-01

Aluminum (Al) foil, as the most accepted cathode current collector for lithium-ion batteries (LIBs), is susceptible to local anodic corrosions during long-term operations. Such corrosions could lead to the deterioration or even premature failure of the batteries and are generally believed to be a bottleneck for next-generation 5 V LIBs. Here, it is demonstrated that Al foil armored by conformal graphene coating exhibits significantly reinforced anodic corrosion resistance in both LiPF 6 and lithium bis(trifluoromethanesulphonyl) imide (LiTFSI) based electrolytes. Moreover, LiMn 2 O 4 cells using graphene-armored Al foil as current collectors (LMO/GA) demonstrate enhanced electrochemical performance in comparison with those using pristine Al foil (LMO/PA). The long-term discharge capacity retention of LMO/GA cell after ≈950 h straight operations at low rate (0.5 C) reaches up to 91%, remarkably superior to LMO/PA cell (75%). The self-discharge propensity of LMO/GA is clearly relieved and the rate/power performance is also improved with graphene mediations. This work not only contributes to the long-term stable operations of LIBs but also might catalyze the deployment of 5 V LIBs in the future. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A large-scale field trial of thin-layer capping of PCDD/F-contaminated sediments: Sediment-to-water fluxes up to 5 years post-amendment.

PubMed

Cornelissen, Gerard; Schaanning, Morten; Gunnarsson, Jonas S; Eek, Espen

2016-04-01

The longer-term effect (3-5 y) of thin-layer capping on in situ sediment-to-surface water fluxes was monitored in a large-scale field experiment in the polychlorinated dibenzodioxin and dibenzofuran (PCDD/F) contaminated Grenlandfjords, Norway (4 trial plots of 10,000 to 40,000 m(2) at 30 to 100 m water depth). Active caps (designed thickness 2.5 cm) were established in 2 fjords, consisting of dredged clean clay amended with powdered activated carbon (PAC) from anthracite. These active caps were compared to 2 nonactive caps in one of the fjords (designed thickness 5 cm) consisting of either clay only (i.e., without PAC) or crushed limestone. Sediment-to-water PCDD/F fluxes were measured in situ using diffusion chambers. An earlier study showed that during the first 2 years after thin-layer capping, flux reductions relative to noncapped reference fields were more extensive at the fields capped with nonactive caps (70%-90%) than at the ones with PAC-containing caps (50%-60%). However, the present work shows that between 3 and 5 years after thin-layer capping, this trend was reversed and cap effectiveness in reducing fluxes was increasing to 80% to 90% for the PAC caps, whereas cap effectiveness of the nonactive caps decreased to 20% to 60%. The increasing effectiveness over time of PAC-containing "active" caps is explained by a combination of slow sediment-to-PAC mass transfer of PCDD/Fs and bioturbation by benthic organisms. The decreasing effectiveness of "nonactive" limestone and clay caps is explained by deposition of contaminated particles on top of the caps. The present field data indicate that the capping efficiency of thin active caps (i.e., enriched with PAC) can improve over time as a result of slow diffusive PCDD/F transfer from sediment to PAC particles and better mixing of the PAC by bioturbation. © 2015 SETAC.

Combinatorial expression of Lef1, Lhx2, Lhx5, Lhx9, Lmo3, Lmo4, and Prox1 helps to identify comparable subdivisions in the developing hippocampal formation of mouse and chicken

PubMed Central

Abellán, Antonio; Desfilis, Ester; Medina, Loreta

2014-01-01

We carried out a study of the expression patterns of seven developmental regulatory genes (Lef1, Lhx2, Lhx9, Lhx5, Lmo3, Lmo4, and Prox1), in combination with topological position, to identify the medial pallial derivatives, define its major subdivisions, and compare them between mouse and chicken. In both species, the medial pallium is defined as a pallial sector adjacent to the cortical hem and roof plate/choroid tela, showing moderate to strong ventricular zone expression of Lef1, Lhx2, and Lhx9, but not Lhx5. Based on this, the hippocampal formation (indusium griseum, dentate gyrus, Ammon's horn fields, and subiculum), the medial entorhinal cortex, and part of the amygdalo-hippocampal transition area of mouse appeared to derive from the medial pallium. In the chicken, based on the same position and gene expression profile, we propose that the hippocampus (including the V-shaped area), the parahippocampal area (including its caudolateral part), the entorhinal cortex, and the amygdalo-hippocampal transition area are medial pallial derivatives. Moreover, the combinatorial expression of Lef1, Prox1, Lmo4, and Lmo3 allowed the identification of dentate gyrus/CA3-like, CA1/subicular-like, and medial entorhinal-like comparable sectors in mouse and chicken, and point to the existence of mostly conserved molecular networks involved in hippocampal complex development. Notably, while the mouse medial entorhinal cortex derives from the medial pallium (similarly to the hippocampal formation, both being involved in spatial navigation and spatial memory), the lateral entorhinal cortex (involved in processing non-spatial, contextual information) appears to derive from a distinct dorsolateral caudal pallial sector. PMID:25071464

Comparison of Listeria monocytogenes Exoproteomes from biofilm and planktonic state: Lmo2504, a protein associated with biofilms.

PubMed

Lourenço, António; de Las Heras, Aitor; Scortti, Mariela; Vazquez-Boland, Jose; Frank, Joseph F; Brito, Luisa

2013-10-01

The food-borne pathogen Listeria monocytogenes is the causative agent of the severe human and animal disease listeriosis. The persistence of this bacterium in food processing environments is mainly attributed to its ability to form biofilms. The search for proteins associated with biofilm formation is an issue of great interest, with most studies targeting the whole bacterial proteome. Nevertheless, exoproteins constitute an important class of molecules participating in various physiological processes, such as cell signaling, pathogenesis, and matrix remodeling. The aim of this work was to quantify differences in protein abundance between exoproteomes from a biofilm and from the planktonic state. For this, two field strains previously evaluated to be good biofilm producers (3119 and J311) were used, and a procedure for the recovery of biofilm exoproteins was optimized. Proteins were resolved by two-dimensional difference gel electrophoresis and identified by electrospray ionization-tandem mass spectrometry. One of the proteins identified in higher abundance in the biofilm exoproteomes of both strains was the putative cell wall binding protein Lmo2504. A mutant strain with deletion of the gene for Lmo2504 was produced (3119Δlmo2504), and its biofilm-forming ability was compared to that of the wild type using the crystal violet and the ruthenium red assays as well as scanning electron microscopy. The results confirmed the involvement of Lmo2504 in biofilm formation, as strain 3119Δlmo2504 showed a significantly (P < 0.05) lower biofilm-forming ability than the wild type. The identification of additional exoproteins associated with biofilm formation may lead to new strategies for controlling this pathogen in food processing facilities.

Devon island ice cap: core stratigraphy and paleoclimate.

PubMed

Koerner, R M

1977-04-01

Valuable paleoclimatic information can be gained by studying the distribution of melt layers in deep ice cores. A profile representing the percentage of ice in melt layers in a core drilled from the Devon Island ice cap plotted against both time and depth shows that the ice cap has experienced a period of very warm summers since 1925, following a period of colder summers between about 1600 and 1925. The earlier period was coldest between 1680 and 1730. There is a high correlation between the melt-layer ice percentage and the mass balance of the ice cap. The relation between them suggests that the ice cap mass balance was zero (accumulation equaled ablation) during the colder period but is negative in the present warmer one. There is no firm evidence of a present cooling trend in the summer conditions on the ice cap. A comparison with the melt-layer ice percentage in cores from the other major Canadian Arctic ice caps shows that the variation of summer conditions found for the Devon Island ice cap is representative for all the large ice caps for about 90 percent of the time. There is also a good correlation between melt-layer percentage and summer sea-ice conditions in the archipelago. This suggests that the search for the northwest passage was influenced by changing climate, with the 19th-century peak of the often tragic exploration coinciding with a period of very cold summers.

Improving the photoresponse spectra of BaSi2 layers by capping with hydrogenated amorphous Si layers prepared by radio-frequency hydrogen plasma

NASA Astrophysics Data System (ADS)

Xu, Zhihao; Gotoh, Kazuhiro; Deng, Tianguo; Sato, Takuma; Takabe, Ryota; Toko, Kaoru; Usami, Noritaka; Suemasu, Takashi

2018-05-01

We studied the surface passivation effect of hydrogenated amorphous silicon (a-Si:H) layers on BaSi2 films. a-Si:H was formed by an electron-beam evaporation of Si, and a supply of atomic hydrogen using radio-frequency plasma. Surface passivation effect was first investigated on a conventional n-Si(111) substrate by capping with 20 nm-thick a-Si:H layers, and next on a 0.5 μm-thick BaSi2 film on Si(111) by molecular beam epitaxy. The internal quantum efficiency distinctly increased by 4 times in a wide wavelength range for sample capped in situ with a 3 nm-thick a-Si:H layer compared to those capped with a pure a-Si layer.

Identification of Lmo1 as part of a Hox-dependent regulatory network for hindbrain patterning.

PubMed

Matis, Christelle; Oury, Franck; Remacle, Sophie; Lampe, Xavier; Gofflot, Françoise; Picard, Jacques J; Rijli, Filippo M; Rezsohazy, René

2007-09-01

The embryonic functions of Hox proteins have been extensively investigated in several animal phyla. These transcription factors act as selectors of developmental programmes, to govern the morphogenesis of multiple structures and organs. However, despite the variety of morphogenetic processes Hox proteins are involved in, only a limited set of their target genes has been identified so far. To find additional targets, we used a strategy based upon the simultaneous overexpression of Hoxa2 and its cofactors Pbx1 and Prep in a cellular model. Among genes whose expression was upregulated, we identified LMO1, which codes for an intertwining LIM-only factor involved in protein-DNA oligomeric complexes. By analysing its expression in Hox knockout mice, we show that Lmo1 is differentially regulated by Hoxa2 and Hoxb2, in specific columns of hindbrain neuronal progenitors. These results suggest that Lmo1 takes part in a Hox paralogue 2-dependent network regulating anteroposterior and dorsoventral hindbrain patterning. (c) 2007 Wiley-Liss, Inc.

Cross-plane thermoelectric transport in p-type La0.67Sr0.33MnO3/LaMnO3 oxide metal/semiconductor superlattices

NASA Astrophysics Data System (ADS)

Jha, Pankaj; Sands, Timothy D.; Jackson, Philip; Bomberger, Cory; Favaloro, Tela; Hodson, Stephen; Zide, Joshua; Xu, Xianfan; Shakouri, Ali

2013-05-01

The cross-plane thermoelectric transport properties of La0.67Sr0.33MnO3 (LSMO)/LaMnO3 (LMO) oxide metal/semiconductor superlattices were investigated. The LSMO and LMO thin-film depositions were performed using pulsed laser deposition to achieve low resistivity constituent materials for LSMO/LMO superlattice heterostructures on (100)-strontium titanate substrates. X-ray diffraction and high-resolution reciprocal space mapping indicate that the superlattices are epitaxial and pseudomorphic. Cross-plane devices were fabricated by etching cylindrical pillar structures in superlattices using inductively, this coupled-plasma reactive-ion etching. The cross-plane electrical conductivity data for LSMO/LMO superlattices reveal a lowering of the effective barrier height to 223 meV as well as an increase in cross-plane conductivity by an order of magnitude compared to high resistivity superlattices. These results suggest that controlling the oxygen deficiency in the constituent materials enables modification of the effective barrier height and increases the cross-plane conductivity in oxide superlattices. The cross-plane LSMO/LMO superlattices showed a giant Seebeck coefficient of 2560 μV/K at 300 K that increases to 16 640 μV/K at 360 K. The giant increase in the Seebeck coefficient with temperature may include a collective contribution from the interplay of charge, spin current, and phonon drag. The low resistance oxide superlattices exhibited a room temperature cross-plane thermal conductivity of 0.92 W/m K, this indicating that the suppression of thermal conductivities due to the interfaces is preserved in both low and high resistivity superlattices. The high Seebeck coefficient, the order of magnitude improvement in cross-plane conductivity, and the low thermal conductivity in LSMO/LMO superlattices resulted in a two order of magnitude increase in cross-plane power factor and thermoelectric figure of merit (ZT), compared to the properties of superlattices with higher resistivity that were reported previously. The temperature dependence of the cross-plane power factor in low resistance superlattices suggests a direction for further investigations of the potential LSMO/LMO oxide superlattices for thermoelectric devices.

A chemical model for generating the sources of mare basalts - Combined equilibrium and fractional crystallization of the lunar magmasphere

NASA Technical Reports Server (NTRS)

Snyder, Gregory A.; Taylor, Lawrence A.; Neal, Clive R.

1992-01-01

A chemical model for simulating the sources of the lunar mare basalts was developed by considering a modified mafic cumulate source formed during the combined equilibrium and fractional crystallization of a lunar magma ocean (LMO). The parameters which influence the initial LMO and its subsequent crystallization are examined, and both trace and major elements are modeled. It is shown that major elements tightly constrain the composition of mare basalt sources and the pathways to their creation. The ability of this LMO model to generate viable mare basalt source regions was tested through a case study involving the high-Ti basalts.

Grhl3 and Lmo4 play coordinate roles in epidermal migration.

PubMed

Hislop, Nikki R; Caddy, Jacinta; Ting, Stephen B; Auden, Alana; Vasudevan, Sumitha; King, Sarah L; Lindeman, Geoffrey J; Visvader, Jane E; Cunningham, John M; Jane, Stephen M

2008-09-01

In addition to its role in formation of the epidermal barrier, the mammalian transcription factor Grainy head-like 3 (Grhl3) is also essential for neural tube closure and wound repair, processes that are dependent in part on epidermal migration. Here, we demonstrate that the LIM-only domain protein, LMO4 serves as a functional partner of GRHL3 in its established roles, and define a new cooperative role for these factors in another developmental epidermal migration event, eyelid fusion. GRHL3 and LMO4 interact biochemically and genetically, with mutant mice exhibiting fully penetrant exencephaly, thoraco-lumbo-sacral spina bifida, defective skin barrier formation, and a co-incident eyes-open-at-birth (EOB) phenotype, which is not observed in the original individual null lines. The two genes are co-expressed in the surface ectoderm of the migrating eyelid root, and electron microscopy of Grhl3/Lmo4-null eyes reveals a failure in epithelial extension and a lack of peridermal clump formation at the eyelid margins. Accumulation of actin fibers is also absent in the circumference of these eyelids, and ERK1/2 phosphorylation is lost in the epidermis and eyelids of Grhl3(-/-)/Lmo4(-/-) embryos. Keratinocytes from mutant mice fail to "heal" in in vitro scratch assays, consistent with a general epidermal migratory defect that is dependent on ERK activation and actin cable formation.

Communication: Distinguishing between bulk and interface-enhanced crystallization in nanoscale films of amorphous solid water.

PubMed

Yuan, Chunqing; Smith, R Scott; Kay, Bruce D

2017-01-21

The crystallization of amorphous solid water (ASW) nanoscale films was investigated using reflection absorption infrared spectroscopy. Two ASW film configurations were studied. In one case the ASW film was deposited on top of and capped with a decane layer ("sandwich" configuration). In the other case, the ASW film was deposited on top of a decane layer and not capped ("no cap" configuration). Crystallization of ASW films in the "sandwich" configuration is about eight times slower than in the "no cap." Selective placement of an isotopic layer (5% D 2 O in H 2 O) at various positions in an ASW (H 2 O) film was used to determine the crystallization mechanism. In the "sandwich" configuration, the crystallization kinetics were independent of the isotopic layer placement whereas in the "no cap" configuration the closer the isotopic layer was to the vacuum interface, the earlier the isotopic layer crystallized. These results are consistent with a mechanism whereby the decane overlayer suppresses surface nucleation and provide evidence that the observed ASW crystallization in "sandwich" films is the result of uniform bulk nucleation.

Selective layer disordering in intersubband Al 0.028Ga 0.972 N/AlN superlattices with silicon nitride capping layer

DOE PAGES

Wierer, Jonathan J.; Allerman, Andrew A.; Skogen, Erik J.; ...

2015-06-01

We demonstrate the selective layer disordering in intersubband Al 0.028Ga 0.972 N/AlN superlattices using a silicon nitride (SiN x) capping layer. The (SiN x) capped superlattice exhibits suppressed layer disordering under high-temperature annealing. In addition, the rate of layer disordering is reduced with increased SiN x thickness. The layer disordering is caused by Si diffusion, and the SiN x layer inhibits vacancy formation at the crystal surface and ultimately, the movement of Al and Ga atoms across the heterointerfaces. In conclusion, patterning of the SiN x layer results in selective layer disordering, an attractive method to integrate active and passivemore » III–nitride-based intersubband devices.« less

Hybrid grating reflectors: Origin of ultrabroad stopband

NASA Astrophysics Data System (ADS)

Park, Gyeong Cheol; Taghizadeh, Alireza; Chung, Il-Sug

2016-04-01

Hybrid grating (HG) reflectors with a high-refractive-index cap layer added onto a high contrast grating (HCG) provide a high reflectance close to 100% over a broader wavelength range than HCGs. The combination of a cap layer and a grating layer brings a strong Fabry-Perot (FP) resonance as well as a weak guided mode (GM) resonance. Most of the reflected power results from the FP resonance, while the GM resonance plays a key role in achieving a reflectance close to 100% as well as broadening the stopband. An HG sample with 7 InGaAlAs quantum wells included in the cap layer has been fabricated by directly wafer-bonding a III-V cap layer onto a Si grating layer. Its reflection property has been characterized. This heterogeneously integrated HG reflector may allow for a hybrid III-V on Si laser to be thermally efficient, which has promising prospects for silicon photonics light sources and high-speed operation.

The Residual Polar Caps of Mars: Geological Differences and Possible Consequences

NASA Technical Reports Server (NTRS)

Thomas, P. C.; Sullivan, R.; Ingersoll, A. P.; Murray, B. C.; Danielson, G. E.; Herkenhoff, K. E.; Soderblom, L.; Malin, M. C.; Edgett, K. S.; James, P. B.

2000-01-01

The Martian polar regions have been known to have thick layered sequences (presumed to consist of silicates and ice), CO2 seasonal frost, and residual frosts that remain through the summer: H2O in the north, largely CO2 in the south. The relationship of the residual frosts to the underlying layered deposits could not be determined from Viking images. The Mars Orbiter Camera on Mars Global Surveyor has provided a 50-fold increase in resolution that shows more differences between the two poles. The north residual cap surface has rough topography of pits, cracks, and knobs, suggestive of ablational forms. This topography is less than a few meters in height, and grades in to surfaces exposing the layers underneath. In contrast, the south residual cap has distinctive collapse and possibly ablational topography emplaced in four or more layers, each approx. two meters thick. The top surface has polygonal depressions suggestive of thermal contraction cracks. The collapse and erosional forms include circular and cycloidal depressions, long sinuous troughs, and nearly parallel sets of troughs. The distinctive topography occurs throughout the residual cap area, but not outside it. Unconformities exposed in polar layers, or other layered materials, do not approximate the topography seen on the south residual cap. The coincidence of a distinct geologic feature, several layers modified by collapse, ablation, and mass movement with the residual cap indicates a distinct composition and/or climate compared to both the remainder of the south polar layered units and those in the north.

Viscosity and Structure of a Late Lunar Magma Ocean Liquid: Implications for the Purity of Ferroan Anorthosites and the Dynamics of a Crystallizing Magma Ocean

NASA Astrophysics Data System (ADS)

Dygert, N. J.; Lin, J. F.; Marshall, E. W., IV; Kono, Y.; Gardner, J. E.

2016-12-01

The current paradigm argues the Moon formed after a giant impact that produced a deep lunar magma ocean (LMO). After a period of turbulent convection, the LMO experienced fractional crystallization, causing the initially peridotitic liquid to evolve to a plagioclase-saturated ferrobasalt. The lunar crust, much of which comprises 93-98% pure anorthosite [1,2], formed by flotation of positively buoyant plagioclase on the residual liquid. A flotation crust would contain some trapped melt; compaction of the melt out of the crust before solidification may be necessary to generate a very pure anorthitic crust. The efficiency of this process depends on the previously unmeasured viscosity of the residual liquid [3]. To characterize the viscosity and thermal equation of state of a late LMO liquid, we conducted experiments at the Advanced Photon Source, Beamline 16-BM-B, Argonne National Laboratory on a nominally anhydrous Ti-rich ferrobasalt [4]. X-ray radiography and diffuse scattering experiments were conducted in a Paris-Edinburgh apparatus in graphite-lined BN capsules, allowing in-situ observation of viscosity and derivation of thermal EoS at P-T conditions relevant to the Moon (1300-1600°C, 0.1-4.4GPa). We calculated viscosities of 0.23-1.45 Pa·s for the melt; based on 11 observations, we find that viscosity is pressure insensitive under the conditions explored. Viscosity can be modeled by an Arrhenius relation with an activation enthalpy of 66 kJ/mol. Composition-dependent predictive models [5] overestimate our observations by roughly a factor of 2. Preliminary analysis suggests no pressure-dependent structural transition over the conditions explored. Late LMO liquids brought to the lunar core-mantle boundary by cumulate mantle overturn may be positively buoyant, implying the seismically attenuating layer around the lunar core contains a denser, higher-Ti melt. Our results suggest that efficient phase segregation in the lunar magma ocean and compaction in the anorthositic flotation crust can produce a high-purity crust under physically reasonable conditions. [1] Warren (1990), AmMin 75, 46-58. [2] Ohtake et al. (2009), Nature 461, 236-240. [3] Piskorz, & Stevenson (2014), Icarus 239, 238-243. [4] Longhi (2003), JGR 108, doi:10.1029/2002JE001941. [5] Giordano et al. (2008), EPSL 271, 123-134.

Negative ?Nd in Anorthositic Clasts in Yamato 86032 and MAC88105: Evidence for the LMO?

NASA Astrophysics Data System (ADS)

Nyquist, L. E.; Bogard, D. D.; Shih, C. Y.; Wiesmann, H.

2002-03-01

The LMO model predicts flotation cumulates with negative epsilon Nd values, but Apollo 16 FANs have positive epsilon Nd values. Ar-Ar ages plus bulk-rock Sm-Nd data for two FAN breccias from two lunar meteorites give negative epsilon Nd values.

Spring Slide

NASA Image and Video Library

2013-10-30

The North Polar region of Mars is capped with layers of water ice and dust, called the polar layered deposits. This permanent polar cap is covered in the winter with a layer of seasonal carbon dioxide ice as seen by NASA Mars Reconnaissance Orbiter.

Surface acoustic waves in one-dimensional piezoelectric-metallic phononic crystal: Effect of a cap layer.

PubMed

Alami, M; El Boudouti, E H; Djafari-Rouhani, B; El Hassouani, Y; Talbi, A

2018-06-18

We study the propagation of transverse acoustic waves associated with the surface of a semi-infinite superlattice (SL) composed of piezoelectric-metallic layers and capped with a piezoelectric layer. We present closed-form expressions for localized surface waves, the so-called Bleustein-Gulyaev (BG) waves depending on whether the cap layer is open-circuited or short-circuited. These expressions are obtained by means of the Green's function method which enables to deduce also the densities of states. These theoretical results are illustrated by a few numerical applications to SLs made of piezoelectric layers of hexagonal symmetry belonging to the 6 mm class such as PZT4 and ZnO in contact with metallic layers such as Fe, Al, Au, Cu and boron-doped-diamond. We demonstrate a rule about the existence of surface modes when considering two complementary semi-infinite SLs obtained by the cleavage of an infinite SL along a plane parallel to the piezoelectric layers. Indeed, when the surface layers are open-circuited, one obtains one surface mode per gap, this mode is associated with one of the two complementary SLs. However, when the surface layers are short-circuited, this rule is not fulfilled and one can obtain zero, one or two modes inside each gap of the two complementary SLs depending on the position of the plane where the cleavage is produced. We show that in addition to the BG surface waves localized at the surface of the cap layer, there may exist true guided waves and pseudo-guided waves (i.e. leaky waves) induced by the cap layer either inside the gaps or inside the bands of the SL respectively. Also, we highlight the possibility of existence of interface modes between the SL and a cap layer as well as an interaction between these modes and the BG surface mode when both modes fall in the same band gaps of the SL. The strength of the interaction depends on the width of the cap layer. Finally, we show that the electromechanical coupling coefficient (ECC) is very sensitive to the cap layer thickness, in particular we calculate and discuss the behavior of the ECC as a function of the adlayer thickness for the low velocity surface modes of the SL which exhibit the highest ECC values. The effect of the nature of the metallic layers inside the SL on the ECC is also investigated. The different surface modes discussed in this work should have applications in sensing applications. Copyright © 2018. Published by Elsevier B.V.

Static and dynamic properties of Co2FeAl thin films: Effect of MgO and Ta as capping layers

NASA Astrophysics Data System (ADS)

Husain, Sajid; Barwal, Vineet; Kumar, Ankit; Behera, Nilamani; Akansel, Serkan; Goyat, Ekta; Svedlindh, Peter; Chaudhary, Sujeet

2017-05-01

The influence of MgO and Ta capping layers on the static and dynamic magnetic properties of Co2FeAl (CFA) Heusler alloy thin films has been investigated. It is observed that the CFA film deposited with MgO capping layer is preeminent compared to the uncapped or Ta capped CFA film. In particular, the magnetic inhomogeneity contribution to the ferromagnetic resonance line broadening and damping constant are found to be minimal for the MgO capped CFA thin film i.e., 0.12±0.01 Oe and 0.0074±0.00014, respectively. The saturation magnetization was found to be 960±25emu/cc.

Mo/Si multilayers with enhanced TiO II- and RuO II-capping layers

NASA Astrophysics Data System (ADS)

Yulin, Sergiy; Benoit, Nicolas; Feigl, Torsten; Kaiser, Norbert; Fang, Ming; Chandhok, Manish

2008-03-01

The lifetime of Mo/Si multilayer-coated projection optics is one of the outstanding issues on the road of commercialization of extreme-ultraviolet lithography (EUVL). The application of Mo/Si multilayer optics in EUVL requires both sufficient radiation stability and also the highest possible normal-incidence reflectivity. A serious problem of conventional high-reflective Mo/Si multilayers capped by silicon is the considerable degradation of reflective properties due to carbonization and oxidation of the silicon surface layer under exposure by EUV radiation. In this study, we focus on titanium dioxide (TiO II) and ruthenium dioxide (RuO II) as promising capping layer materials for EUVL multilayer coatings. The multilayer designs as well as the deposition parameters of the Mo/Si systems with different capping layers were optimized in terms of maximum peak reflectivity at the wavelength of 13.5 nm and longterm stability under high-intensive irradiation. Optimized TiO II-capped Mo/Si multilayer mirrors with an initial reflectivity of 67.0% presented a reflectivity drop of 0.6% after an irradiation dose of 760 J/mm2. The reflectivity drop was explained by the partial oxidation of the silicon sub-layer. No reflectivity loss after similar irradiation dose was found for RuO II-capped Mo/Si multilayer mirrors having initial peak reflectivity of 66%. In this paper we present data on improved reflectivity of interface-engineered TiO II- and RuO II-capped Mo/Si multilayer mirrors due to the minimization of both interdiffusion processes inside the multilayer stack and absorption loss in the oxide layer. Reflectivities of 68.5% at the wavelength of 13.4 nm were achieved for both TiO II- and RuO II-capped Mo/Si multilayer mirrors.

North-south geological differences between the residual polar caps on Mars

USGS Publications Warehouse

Thomas, P.C.; Malin, M.C.; Edgett, K.S.; Carr, M.H.; Hartmann, W.K.; Ingersoll, A.P.; James, P.B.; Soderblom, L.A.; Veverka, J.; Sullivan, R.

2000-01-01

Polar processes can be sensitive indicators of global climate, and the geological features associated with polar ice caps can therefore indicate evolution of climate with time. The polar regions on Mars have distinctive morphologic and climatologic features: thick layered deposits, seasonal CO2 frost caps extending to mid latitudes, and near-polar residual frost deposits that survive the summer. The relationship of the seasonal and residual frost caps to the layered deposits has been poorly constrained, mainly by the limited spatial resolution of the available data. In particular, it has not been known if the residual caps represent simple thin frost cover or substantial geologic features. Here we show that the residual cap on the south pole is a distinct geologic unit with striking collapse and erosional topography; this is very different from the residual cap on the north pole, which grades into the underlying layered materials. These findings indicate that the differences between the caps are substantial (rather than reflecting short-lived differences in frost cover), and so support the idea of long-term asymmetry in the polar climates of Mars.

Chromatin Immunoprecipitation and DNA Sequencing Identified a LIMS1/ILK Pathway Regulated by LMO1 in Neuroblastoma.

PubMed

Saeki, Norihisa; Saito, Akira; Sugaya, Yuki; Amemiya, Mitsuhiro; Ono, Hiroe; Komatsuzaki, Rie; Yanagihara, Kazuyoshi; Sasaki, Hiroki

2018-01-01

Overall survival for the high-risk group of neuroblastoma (NB) remains at 40-50%. An integrative genomics study revealed that LIM domain only 1 (LMO1) encoding a transcriptional regulator to be an NB-susceptibility gene with a tumor-promoting activity, that needs to be revealed. We conducted chromatin immunoprecipitation and DNA sequencing analyses and cell proliferation assays on two NB cell lines. We identified three genes regulated by LMO1 in the cells, LIM and senescent cell antigen-like domains 1 (LIMS1), Ras suppressor protein 1 (RSU1) and relaxin 2 (RLN2). LIMS1 and RSU1 encode proteins functioning with integrin-linked kinase (ILK), and inhibition of LIMS1, ILK or RLN2 by shRNA reduced cell proliferation of the NB cells, which was also suppressed with an ILK inhibiting compound Cpd 22. The downstream of LMO1-regulatory cascade includes a tumor-promoting LIMS1/ILK pathway, which has a potential to be a novel therapeutic target. Copyright© 2018, International Institute of Anticancer Research (Dr. George J. Delinasios), All rights reserved.

Influence of ammonium hydroxide solution on LiMn2O4 nanostructures prepared by modified chemical bath method

NASA Astrophysics Data System (ADS)

Koao, Lehlohonolo F.; Motloung, Setumo V.; Motaung, Tshwafo E.; Kebede, Mesfin A.

2018-04-01

LiMn2O4 (LMO) powders were prepared by modified chemical bath deposition (CBD) method by varying ammonium hydroxide solution (AHS). The volume of the AHS was varied from 5 to 120 mL in order to determine the optimum volume that is needed for preparation of LMO powders. The effect of AHS volume on the structure, morphology, and electrochemical properties of LMO powders was investigated. The X-ray diffraction (XRD) patterns of the LMO powders correspond to the cubic spinel LMO phase. It was found that the XRD peaks increased in intensity with increasing volume of the AHS up to 20 mL. The estimated average grain sizes calculated using the XRD patterns were found to be in the order of 66 ± 1 nm. It was observed that the estimated average grain sizes increased up to 20 mL of AHS. The scanning electron microscopy (SEM) results revealed that the AHS volume does not influence the surface morphology of the prepared nano-powders. Elemental energy dispersive (EDS) analysis mapping conducted on the samples revealed homogeneous distribution of Mn and O for the sample synthesized with 120 mL of AHS. The UV-Vis spectra showed a red shift with an increase in AHS up 20 mL. The cyclic voltammetry and galvanostatic charge/discharge cycle testing confirmed that 20 mL of AHS has superior lithium ion kinetics and electrochemical performance.

Damage of multilayer optics with varying capping layers induced by focused extreme ultraviolet beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jody Corso, Alain; Nicolosi, Piergiorgio; Nardello, Marco

2013-05-28

Extreme ultraviolet Mo/Si multilayers protected by capping layers of different materials were exposed to 13.5 nm plasma source radiation generated with a table-top laser to study the irradiation damage mechanism. Morphology of single-shot damaged areas has been analyzed by means of atomic force microscopy. Threshold fluences were evaluated for each type of sample in order to determine the capability of the capping layer to protect the structure underneath.

Hybrid calcium phosphate coatings for implants

NASA Astrophysics Data System (ADS)

Malchikhina, Alena I.; Shesterikov, Evgeny V.; Bolbasov, Evgeny N.; Ignatov, Viktor P.; Tverdokhlebov, Sergei I.

2016-08-01

Monophasic biomaterials cannot provide all the necessary functions of bones or other calcined tissues. It is necessary to create for cancer patients the multiphase materials with the structure and composition simulating the natural bone. Such materials are classified as hybrid, obtained by a combination of chemically different components. The paper presents the physical, chemical and biological studies of coatings produced by hybrid technologies (HT), which combine primer layer and calcium phosphate (CaP) coating. The first HT type combines the method of vacuum arc titanium primer layer deposition on a stainless steel substrate with the following micro-arc oxidation (MAO) in phosphoric acid solution with addition of calcium compounds to achieve high supersaturated state. MAO CaP coatings feature high porosity (2-8%, pore size 5-7 µm) and surface morphology with the thickness greater than 5 µm. The thickness of Ti primer layer is 5-40 µm. Amorphous MAO CaP coating micro-hardness was measured at maximum normal load Fmax = 300 mN. It was 3.1 ± 0.8 GPa, surface layer elasticity modulus E = 110 ± 20 GPa, roughness Ra = 0.9 ± 0.1 µm, Rz = 7.5 ± 0.2 µm, which is less than the titanium primer layer roughness. Hybrid MAO CaP coating is biocompatible, able to form calcium phosphates from supersaturated body fluid (SBF) solution and also stimulates osteoinduction processes. The second HT type includes the oxide layer formation by thermal oxidation and then CaP target radio frequency magnetron sputtering (RFMS). Oxide-RFMS CaP coating is a thin dense coating with good adhesion to the substrate material, which can be used for metal implants. The RFMS CaP coating has thickness 1.6 ± 0.1 µm and consists of main target elements calcium and phosphorus and Ca/P ratio 2.4. The second HT type can form calcium phosphates from SBF solution. In vivo study shows that hybrid RFMS CaP coating is biocompatible and produces fibrointegration processes.

Optical and structural characteristics of high indium content InGaN/GaN multi-quantum wells with varying GaN cap layer thickness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, J.; Zhao, D. G., E-mail: dgzhao@red.semi.ac.cn; Jiang, D. S.

2015-02-07

The optical and structural properties of InGaN/GaN multi-quantum wells (MQWs) with different thicknesses of low temperature grown GaN cap layers are investigated. It is found that the MQW emission energy red-shifts and the peak intensity decreases with increasing GaN cap layer thickness, which may be partly caused by increased floating indium atoms accumulated at quantum well (QW) surface. They will result in the increased interface roughness, higher defect density, and even lead to a thermal degradation of QW layers. An extra growth interruption introduced before the growth of GaN cap layer can help with evaporating the floating indium atoms, andmore » therefore is an effective method to improve the optical properties of high indium content InGaN/GaN MQWs.« less

The Interior of the Moon, Core Formation, and the Lunar Hotspot: What Samples Tell Us

NASA Astrophysics Data System (ADS)

Neal, C. R.

1999-01-01

Remotely-gathered Lunar Prospector data have demonstrated the existence of a lunar "hotspot" on the near side of the Moon. This hotspot contains relatively high abundances of KREEPy incompatible trace elements (i.e., Th). It is generally accepted that primordial KREEP or urKREEP represents the residual liquid after the crystallization of a lunar magma ocean (LMO). The crystalline products from the LMO formed the source regions for the mare basalts. Lunar volcanic glasses cannot be genetically related to the crystalline mare basalts, and experimental petrology indicates they are derived from greater (> 400 km) depths than the mare basalts. Questions to be addressed include: (1) What was the extent of LMO melting? (2) What is the composition of the core? (3) Are there distinct geochemical reservoirs in the Moon? (4) Is there evidence of garnet in the lunar interior? (5) What caused the formation of the lunar hotspot? The scale of the LMO has been suggested to be whole Moon melting or only the outer about 400 km. If whole Moon melting is invoked, then differentiation of the Moon into a flotation plagioclase-rich crust, a mafic mineral cumulate mantle, and a Fe-rich core is more easily facilitated. However, as pointed out, if the material that formed the Moon came primarily from the already-differentiated Earth mantle, there may not be enough Fe to form a metallic Fe core on the Moon. Authors have suggested that the lunar core is made up of dense, ilmenite-rich, late-stage cumulates from the LMO. This can be tested by examining the Zr/Hf ratios of mare basalts and, where possible, the volcanic glasses. Partition coefficients for Zr and Hf in ilmenite are 0.29-0.32 and 0.4-0.43, respectively, with Zr being less compatible. Therefore, extraction of an "ilmenite" core would have a profound effect on the Zr/Hf ratio of urKREEP as ilmenite is a late-stage fractionating LMO phase. Assuming either a "primitive mantle" or chondritic starting material with a Zr/Hf ratio of 36-37, ilmenite extraction will increase this ratio in the residual liquid. Conversely, derivation of a melt from a source rich in ilmenite will produce a melt of lower Zr/ Hf ratio. Hughes and Schmitt defined a mean Zr/Hf for KREEP of 41.0 +/- 0.4, about 39 for Apollo 15 basalts, and 30-32 for Apollo 11, 12, and 17 basalts, with the decreases in Zr/Hf broadly correlating with La/Yb. However, literature data for Apollo 15 KREEP basalts and the KREEP-rich Apollo 14 mare basalts exhibit little variation in Zr/Hf from 36, indicating the KREEP component did not result from a major fractionation of ilmenite and suggesting that the lunar core is probably metallic in overall composition. With volcanic glasses being unrelated to the mare basalts and derived from greater depths, compositional comparisons allow their source regions to be compared. Highly siderophile elements Au and Ir are more abundant in the glasses relative to the basalts. As these elements are generally incompatible in silicate minerals, crystal fractionation experienced by the basalts will tend to increase the Au and It abundances. Therefore, the glasses may be derived from a source enriched in highly siderophile elements such as the platinum-group elements (PGEs) represented by Ir, relative to the source of the basalts. This observation can be accommodated with the basalts being derived from the LMO cumulates and the glasses derived from a source that represents "primitive Moon" that did not melt and, therefore, did not have its budget of PGEs and Au reduced through core formation. This can be tested by analyzing mare basalts and glasses for the PGEs. Although analytically challenging, the first PGE patterns in lunar samples were demonstrated that the source regions for the different Apollo 12 basalts could not be differentiated on the basis of PGE budgets, although the profiles are typical of silicate melts. Analysis of other trace-element data indicate that the high-field-strength elements can be used to differentiate between high- and low-Ti basalts. Also, the volcanic glasses were derived from a source with a higher Zr/Y ratio relative to the basalts, consistent with retention of garnet in the residue. If the glasses were derived from > 400 km, garnet could be stable. It is concluded that the volcanic glasses were derived from a source that contained garnet, but escaped the melting that formed the LMO. The mare basalts were derived from the LMO cumulate pile. Basaltic samples from Apollo 14 exhibit a range in ITE. They also exhibit a range of ages from 4.33 Ga to 3.96 Ga with the older basalts being KREEP-poor and the younger being KREEP-rich. Prospector mapping has identified relatively high Th abundances in this area, suggesting a large KREEP component is present at or near the surface. LMO "layer cake models" have residual urKREEP sandwiched between the mafic cumulate mantle and the plagioclase flotation cumulate crust. However, late-stage cumulates and the residual liquid will be more dense that the early mafic cumulates resulting in gravitational instabilities and overturn of the cumulate pile. This could transport urKREEP to the base of the LMO cumulate pile, but above the glass source region. The effect of Earth on the symmetry of the Moon has displaced the low-density crust, producing a thicker crust on the farside. This has produced an offset of the center of mass for the Moon toward Earth. It is suggested that the gravitational forces of the Earth pooled the urKREEP beneath at the base of the LMO on the lunar nearside. Heating through radioactive decay produced thermal instabilities, resulting in a plume of hot, KREEPy material rising adiabatically beneath the Apollo 14 site. The oldest Apollo basalts contain no evidence of a KREEPy component, suggesting diapiric rise of the KREEPy plume had not occurred at this time. Additional information contained in original.

Hybrid grating reflectors: Origin of ultrabroad stopband

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Gyeong Cheol; Taghizadeh, Alireza; Chung, Il-Sug, E-mail: ilch@fotonik.dtu.dk

2016-04-04

Hybrid grating (HG) reflectors with a high-refractive-index cap layer added onto a high contrast grating (HCG) provide a high reflectance close to 100% over a broader wavelength range than HCGs. The combination of a cap layer and a grating layer brings a strong Fabry-Perot (FP) resonance as well as a weak guided mode (GM) resonance. Most of the reflected power results from the FP resonance, while the GM resonance plays a key role in achieving a reflectance close to 100% as well as broadening the stopband. An HG sample with 7 InGaAlAs quantum wells included in the cap layer hasmore » been fabricated by directly wafer-bonding a III-V cap layer onto a Si grating layer. Its reflection property has been characterized. This heterogeneously integrated HG reflector may allow for a hybrid III-V on Si laser to be thermally efficient, which has promising prospects for silicon photonics light sources and high-speed operation.« less

Highly improved passivation of c-Si surfaces using a gradient i a-Si:H layer

NASA Astrophysics Data System (ADS)

Lee, Soonil; Ahn, Jaehyun; Mathew, Leo; Rao, Rajesh; Zhang, Zhongjian; Kim, Jae Hyun; Banerjee, Sanjay K.; Yu, Edward T.

2018-04-01

Surface passivation using intrinsic a-Si:H (i a-Si:H) films plays a key role in high efficiency c-Si heterojunction solar cells. In this study, we demonstrate improved passivation quality using i a-Si:H films with a gradient-layered structure consisting of interfacial, transition, and capping layers deposited on c-Si surfaces. The H2 dilution ratio (R) during deposition was optimized individually for the interfacial and capping layers, which were separated by a transition layer for which R changed gradually between its values for the interfacial and capping layers. This approach yielded a significant reduction in surface carrier recombination, resulting in improvement of the minority carrier lifetime from 1480 μs for mono-layered i a-Si:H passivation to 2550 μs for the gradient-layered passivation approach.

Preventing Thin Film Dewetting via Graphene Capping.

PubMed

Cao, Peigen; Bai, Peter; Omrani, Arash A; Xiao, Yihan; Meaker, Kacey L; Tsai, Hsin-Zon; Yan, Aiming; Jung, Han Sae; Khajeh, Ramin; Rodgers, Griffin F; Kim, Youngkyou; Aikawa, Andrew S; Kolaczkowski, Mattew A; Liu, Yi; Zettl, Alex; Xu, Ke; Crommie, Michael F; Xu, Ting

2017-09-01

A monolayer 2D capping layer with high Young's modulus is shown to be able to effectively suppress the dewetting of underlying thin films of small organic semiconductor molecule, polymer, and polycrystalline metal, respectively. To verify the universality of this capping layer approach, the dewetting experiments are performed for single-layer graphene transferred onto polystyrene (PS), semiconducting thienoazacoronene (EH-TAC), gold, and also MoS 2 on PS. Thermodynamic modeling indicates that the exceptionally high Young's modulus and surface conformity of 2D capping layers such as graphene and MoS 2 substantially suppress surface fluctuations and thus dewetting. As long as the uncovered area is smaller than the fluctuation wavelength of the thin film in a dewetting process via spinodal decomposition, the dewetting should be suppressed. The 2D monolayer-capping approach opens up exciting new possibilities to enhance the thermal stability and expands the processing parameters for thin film materials without significantly altering their physical properties. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The effect of different thickness alumina capping layers on the final morphology of dewet thin Ni films

NASA Astrophysics Data System (ADS)

White, Benjamin C.; Behbahanian, Amir; Stoker, T. McKay; Fowlkes, Jason D.; Hartnett, Chris; Rack, Phillip D.; Roberts, Nicholas A.

2018-03-01

Nanoparticles on a substrate have numerous applications in nanotechnology, from enhancements to solar cell efficiency to improvements in carbon nanotube growth. Producing nanoparticles in a cost effective fashion with control over size and spacing is desired, but difficult to do. This work presents a scalable method for altering the radius and pitch distributions of nickel nanoparticles. The introduction of alumina capping layers to thin nickel films during a pulsed laser-induced dewetting process has yielded reductions in the mean and standard deviation of radii and pitch for dewet nanoparticles with no noticeable difference in final morphology with increased capping layer thickness. The differences in carbon nanotube mats grown, on the uncapped sample and one of the capped samples, is also presented here, with a more dense mat being present for the capped case.

The Mars water cycle at other epochs: Recent history of the polar caps and layered terrain

NASA Technical Reports Server (NTRS)

Jakosky, Bruce M.; Henderson, Bradley G.; Mellon, Michael T.

1992-01-01

The Martian polar caps and layered terrain presumably evolves by the deposition and removal of small amounts of water and dust each year, the current cap attributes therefore represent the incremental transport during a single year as integrated over long periods of time. The role was studied of condensation and sublimation of water ice in this process by examining the seasonal water cycle during the last 10(exp 7) yr. In the model, axial obliquity, eccentricity, and L sub s of perihelion vary according to dynamical models. At each epoch, the seasonal variations in temperature are calculated at the two poles, keeping track of the seasonal CO2 cap and the summertime sublimation of water vapor into the atmosphere; net exchange of water between the two caps is calculated based on the difference in the summertime sublimation between the two caps (or on the sublimation from one cap if the other is covered with CO2 frost all year). Results from the model can help to explain (1) the apparent inconsistency between the timescales inferred for layer formation and the much older crater retention age of the cap and (2) the difference in sizes of the two residual caps, with the south being smaller than the north.

Chlorine in Lunar Basalts

NASA Technical Reports Server (NTRS)

Barnes, J. J.; Anand, M.; Franchi, I. A.

2017-01-01

In the context of the lunar magma ocean (LMO) model, it is anticipated that chlorine (and other volatiles) should have been concentrated in the late-stage LMO residual melts (i.e., the dregs enriched in incompatible elements such as K, REEs, and P, collectively called KREEP, and in its primitive form - urKREEP, [1]), given its incompatibility in mafic minerals like olivine and pyroxene, which were the dominant phases that crystallized early in the cumulate pile of the LMO (e.g., [2]). When compared to chondritic meteorites and terrestrial rocks (e.g., [3-4]), lunar samples often display heavy chlorine isotope compositions [5-9]. Boyce et al. [8] found a correlation between delta Cl-37 (sub Ap) and bulk-rock incompatible trace elements (ITEs) in lunar basalts, and used this to propose that early degassing of Cl (likely as metal chlorides) from the LMO led to progressive enrichment in remaining LMO melt in Cl-37over Cl-35- the early degassing model. Barnes et al. [9] suggested that relatively late degassing of chlorine from urKREEP (to yield delta Cl-37 (sub urKREEP greater than +25 per mille) followed by variable mixing between KREEPy melts and mantle cumulates (characterized by delta Cl-370 per mille) could explain the majority of Cl isotope data from igneous lunar samples. In order to better understand the processes involved in giving rise to the heavy chlorine isotope compositions of lunar samples, we have performed an in situ study of chlorine isotopes and abundances of volatiles in lunar apatite from a diverse suite of lunar basalts spanning a range of geochemical types.

The storage degradation of an 18650 commercial cell studied using neutron powder diffraction

NASA Astrophysics Data System (ADS)

Lee, Po-Han; Wu, She-huang; Pang, Wei Kong; Peterson, Vanessa K.

2018-01-01

Commercial 18650 lithium ion cells containing a blended positive electrode of layered LiNi0.5Mn0.3Co0.2O2 and spinel Li1.1Mn1.9O4 alongside a graphite negative electrode were stored at various depth-of-discharge (DoD) at 60 °C for 1, 2, 4, and 6 months. After storage, the cells were cycled at C/25 at 25 °C between 2.75 and 4.2 V for capacity determination and incremental capacity analysis (ICA). In addition to ICA analysis, the mechanism for capacity fade was investigated by combining the results of neutron powder diffraction under in-situ and operando conditions, in conjunction with post-mortem studies of the electrodes using synchrotron X-ray powder diffraction and inductively-coupled plasma optical emission spectroscopy. Among the cells, those stored at 25% DoD suffered the highest capacity fade due to their higher losses of active Li, NMC, and LMO than cells stored at other DoD. The cells stored at 0% DoD shows second high capacity fade because they exhibit the highest of active LMO and graphite anode among the stored cells and higher losses of active Li and NMC than cells stored at 50% DoD.

Magnetohydrodynamic generator electrode

DOEpatents

Marchant, David D.; Killpatrick, Don H.; Herman, Harold; Kuczen, Kenneth D.

1979-01-01

An improved electrode for use as a current collector in the channel of a magnetohydrodynamid (MHD) generator utilizes an elongated monolithic cap of dense refractory material compliantly mounted to the MHD channel frame for collecting the current. The cap has a central longitudinal channel which contains a first layer of porous refractory ceramic as a high-temperature current leadout from the cap and a second layer of resilient wire mesh in contact with the first layer as a low-temperature current leadout between the first layer and the frame. Also described is a monolithic ceramic insulator compliantly mounted to the frame parallel to the electrode by a plurality of flexible metal strips.

South polar residual cap of Mars: Features, stratigraphy, and changes

NASA Astrophysics Data System (ADS)

Thomas, P. C.; Malin, M. C.; James, P. B.; Cantor, B. A.; Williams, R. M. E.; Gierasch, P.

2005-04-01

The south residual polar cap of Mars, rich in CO 2 ice, is compositionally distinct from the north residual cap which is dominantly H 2O ice. The south cap is also morphologically distinct, displaying a bewildering variety of depressions formed in thin layered deposits, which have been observed to change by scarp retreat over an interval of one Mars year (Malin et al., 2001, Science 294, 2146-2148). The climatically sensitive locale of the residual caps suggests that their behavior may help in the interpretation of recent fluctuations or repeatability of the Mars climate. We have used Mars Global Surveyor Mars Orbiter Camera (MOC) images obtained in three southern summers to map the variety of features in the south residual cap and to evaluate changes over two Mars years (Mars y). The images show that there are two distinct layered units which were deposited at different times separated by a period of degradation. The older unit, ˜10 m thick, has layers approximately 2 m thick. The younger unit has variable numbers of layers, each ˜1 m thick. The older unit is eroding by scarp retreat averaging 3.6 m/Mars y, a rate greater than the retreat of 2.2 m/Mars y observed for the younger unit. The rates of scarp retreat and sizes of the different types of depressions indicate that the history of the residual cap has been short periods of deposition interspersed with longer erosional periods. Erosion of the older unit probably occupied ˜100-150 Mars y. One layer may have been deposited after the Mariner 9 observations in 1972. Residual cap layers appear to differ from normal annual winter deposits by having a higher albedo and perhaps by having higher porosities. These properties might be produced by differences in the depositional meteorology that affect the fraction of high porosity snow included in the winter deposition.

[Apatite-forming ability of pure titanium implant after micro-arc oxidation treatment].

PubMed

Tian, Zhihui; Zhang, Yu; Wang, Lichao; Nan, Kaihui

2013-10-01

To investigate the apatite forming ability of pure titanium implant after micro-arc oxidation treatment in simulated body fluid (SBF) and obtain implants with calcium phosphate (Ca-P) layers. The implants were immersed in (SBF) after micro-arc oxidation treatment for different time lengths, and their apatite forming ability and the morphology and constituents of the Ca-P layers formed on the sample surface were analyzed using X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, and energy dispersive electron probe. After immersion in SBF, large quantities of Ca-P layers were induced on the surface of the samples. The Ca-P layers were composed of octacalcium phosphate and carbonated hydroxyapatite, and the crystals showed a plate-like morphology with an oriented growth. The implants with micro-arc oxidation treatment show good apatite forming ability on the surface with rich calcium and phosphorus elements. The formed layers are composed of bone-like apatite including octacalcium phosphate and carbonated hydroxyapatite.

Optimisation of readout performance of phase-change probe memory in terms of capping layer and probe tip

NASA Astrophysics Data System (ADS)

Wang, Lei; Wright, C. David; Aziz, Mustafa. M.; Yang, Ci Hui; Yang, Guo Wei

2014-11-01

The capping layer and the probe tip that serve as the protective layer and the recording tool, respectively, for phase-change probe memory play an important role on the writing performance of phase-change probe memory, thus receiving considerable attention. On the other hand, their influence on the readout performance of phasechange probe memory has rarely been reported before. A three-dimensional parametric study based on the Laplace equation was therefore conducted to investigate the effect of the capping layer and the probe tip on the resulting reading contrast for the two cases of reading a crystalline bit from an amorphous matrix and reading an amorphous bit from a crystalline matrix. The results indicated that a capping layer with a thickness of 2 nm and an electrical conductivity of 50 Ω-1m-1 is able to provide an appropriate reading contrast for both the cases, while satisfying the previous writing requirement, particularly with the assistance of a platinum silicide probe tip.

How did the Lunar Magma Ocean crystallize?

NASA Astrophysics Data System (ADS)

Davenport, J.; Neal, C. R.

2012-12-01

It is generally accepted that the lunar crust and at least the uppermost (500 km) mantle was formed by crystallization of a magma ocean. How the magma ocean cooled and crystallized is still under debate. Parameters such as bulk composition, lunar magma ocean (LMO) crystallization method (fractional vs. equilibrium), depth of the LMO, and time for LMO solidification (effects of tidal heating mechanisms, insulating crustal lid, etc.) are still under debate. Neal (2001, JGR 106, 27865-27885) argues for the presence of garnet in the deep lunar mantle via compositional differences between low- and high-Ti mare basalts and volcanic glasses. Neal (2001) suggests that these compositional differences are due to the presence of garnet in the source regions of certain volcanic glass bead groups. As Neal (2001, JGR 106, 27865-27885) points out, determining if there is garnet in the lunar mantle is important in determining if the LMO was a "whole-Moon" event or if it was limited to certain areas. In the latter case, garnet would have been preserved in the lunar mantle and would have been used in the source material for some of the volcanic glasses. High-pressure experimental work concludes that with the right T-P conditions (2.5-4.5 GPa and 1675-1800° C) there could be a garnet-bearing pyroxene rich protolith at ~500 km depth. This also has significant implications for the bulk Al2O3 composition of the initial bulk Moon. If the LMO was not global, the volcanic glass beads that show evidence of garnet in their sources were formed from the deep, primitive lunar mantle, it begs the questions how was the non-LMO regions of the Moon formed and what was it's bulk composition? To try to answer these questions, it is necessary to thoroughly model the evolution of the LMO and then use that work to model the sources and formation of mare basalts, the volcanic glass beads, and other regions in question. To begin to answer these questions, we developed a scenario we have termed reverse LMO modeling. Geochemical compositions such as KREEP, ur-KREEP and FAN will be run backwards through various LMO models that have been proposed in the literature. The concentration of the initial bulk Moon, according to the concentrations of the particular type of rock being used, can be modeled by taking this from 0 percent liquid (PCL; a completely solidified Moon) to 100 PCL. Using the KREEP composition reported by Warren and Wasson (1979, Rev. of Geophysics and Space Physics 17, 73-88), Warren (1988, Proc. 18th LPSC, 233-241) and Warren (1989, LPI Tech. Report 89, 149-153), the Mg numbers (Mg#) for the bulk initial Moon were calculated yielding 0.87, 0.76, and 0.86 respectively. The major element compositions of calculated bulk Moon compositions have elevated Al2O3, FeO, and TiO2, consistent with the presence of garnet in the lunar mantle as well as generating high-Ti basalts. Using these data we can model the petrogenesis of the low- and high-Ti mare basalt and volcanic glass source regions. Furthermore, using remote sensing and the calculated source data we can compare the modeled concentrations of these rocks to where these ranges of concentrations fall on the Moon's surfaces, so that we can constrain the areas where the presence of a magma ocean on the Moon was possible.

Magnetism in Mn-nanowires and -clusters as δ-doped layers in group IV semiconductors (Si, Ge)

NASA Astrophysics Data System (ADS)

Simov, K. R.; Glans, P.-A.; Jenkins, C. A.; Liberati, M.; Reinke, P.

2018-01-01

Mn doping of group-IV semiconductors (Si/Ge) is achieved by embedding nanostructured Mn-layers in group-IV matrix. The Mn-nanostructures are monoatomic Mn-wires or Mn-clusters and capped with an amorphous Si or Ge layer. The precise fabrication of δ-doped Mn-layers is combined with element-specific detection of the magnetic signature with x-ray magnetic circular dichroism. The largest moment (2.5 μB/Mn) is measured for Mn-wires with ionic bonding character and a-Ge overlayer cap; a-Si capping reduces the moment due to variations of bonding in agreement with theoretical predictions. The moments in δ-doped layers dominated by clusters is quenched with an antiferromagnetic component from Mn-Mn bonding.

Gilbert Damping Parameter in MgO-Based Magnetic Tunnel Junctions from First Principles

NASA Astrophysics Data System (ADS)

Tang, Hui-Min; Xia, Ke

2017-03-01

We perform a first-principles study of the Gilbert damping parameter (α ) in normal-metal/MgO-cap/ferromagnet/MgO-barrier/ferromagnetic magnetic tunnel junctions. The damping is enhanced by interface spin pumping, which can be parametrized by the spin-mixing conductance (G↑↓ ). The calculated dependence of Gilbert damping on the thickness of the MgO capping layer is consistent with experiment and indicates that the decreases in α with increasing thickness of the MgO capping layer is caused by suppression of spin pumping. Smaller α can be achieved by using a clean interface and alloys. For a thick MgO capping layer, the imaginary part of the spin-mixing conductance nearly equals the real part, and the large imaginary mixing conductance implies that the change in the frequency of ferromagnetic resonance can be observed experimentally. The normal-metal cap significantly affects the Gilbert damping.

Worldwide Emerging Environmental Issues Affecting the U.S. Military. March 2006 Report

DTIC Science & Technology

2006-03-01

and their metabolites can increase drug resistance among disease organisms and synthetic hormones can act as endocrine disruptors . Italian...The most important achievement was the adoption of the documentation requirements for LMO shipments for food , feed and processing (LMO-FFPs). The...special management areas, and policies to preserve endangered species - designation of several new protected areas - rejection of lifting the

Thermophotovoltaic energy conversion system having a heavily doped n-type region

DOEpatents

DePoy, David M.; Charache, Greg W.; Baldasaro, Paul F.

2000-01-01

A thermophotovoltaic (TPV) energy conversion semiconductor device is provided which incorporates a heavily doped n-type region and which, as a consequence, has improved TPV conversion efficiency. The thermophotovoltaic energy conversion device includes an emitter layer having first and second opposed sides and a base layer in contact with the first side of the emitter layer. A highly doped n-type cap layer is formed on the second side of the emitter layer or, in another embodiment, a heavily doped n-type emitter layer takes the place of the cap layer.

A heterogeneous lunar interior for hydrogen isotopes as revealed by the lunar highlands samples

NASA Astrophysics Data System (ADS)

Hui, Hejiu; Guan, Yunbin; Chen, Yang; Peslier, Anne H.; Zhang, Youxue; Liu, Yang; Flemming, Roberta L.; Rossman, George R.; Eiler, John M.; Neal, Clive R.; Osinski, Gordon R.

2017-09-01

Knowing the amount and timing of water incorporation into the Moon has fundamental implications for our understanding of how the Earth-Moon system formed. Water has been detected in lunar samples but its abundance, distribution and origin are debated. To address these issues, we report water concentrations and hydrogen isotope ratios obtained by secondary ion mass spectrometry (SIMS) of plagioclase from ferroan anorthosites (FANs), the only available lithology thought to have crystallized directly from the lunar magma ocean (LMO). The measured water contents are consistent with previous results by Fourier transform infrared spectroscopy (FTIR). Combined with literature data, δD values of lunar igneous materials least-degassed at the time of their crystallization range from -280 to + 310 ‰, the latter value being that of FAN 60015 corrected for cosmic ray exposure. We interpret these results as hydrogen isotopes being fractionated during degassing of molecular hydrogen (H2) in the LMO, starting with the magmatic δD value of primordial water at the beginning of LMO being about - 280 ‰, evolving to about + 310 ‰ at the time of anorthite crystallization, i.e. during the formation of the primary lunar crust. The degassing of hydrogen in the LMO is consistent with those of other volatile elements. The wide range of δD values observed in lunar igneous rocks could be due to either various degrees of mixing of the different mantle end members, or from a range of mantle sources that were degassed to different degrees during magma evolution. Degassing of the LMO is a viable mechanism that resulted in a heterogeneous lunar interior for hydrogen isotopes.

A facile approach to nanoarchitectured three-dimensional graphene-based Li-Mn-O composite as high-power cathodes for Li-ion batteries.

PubMed

Zhang, Wenyu; Zeng, Yi; Xu, Chen; Xiao, Ni; Gao, Yiben; Li, Lain-Jong; Chen, Xiaodong; Hng, Huey Hoon; Yan, Qingyu

2012-01-01

We report a facile method to prepare a nanoarchitectured lithium manganate/graphene (LMO/G) hybrid as a positive electrode for Li-ion batteries. The Mn(2)O(3)/graphene hybrid is synthesized by exfoliation of graphene sheets and deposition of Mn(2)O(3) in a one-step electrochemical process, which is followed by lithiation in a molten salt reaction. There are several advantages of using the LMO/G as cathodes in Li-ion batteries: (1) the LMO/G electrode shows high specific capacities at high gravimetric current densities with excellent cycling stability, e.g., 84 mAh·g(-1) during the 500th cycle at a discharge current density of 5625 mA·g(-1) (~38.01 C capacity rating) in the voltage window of 3-4.5 V; (2) the LMO/G hybrid can buffer the Jahn-Teller effect, which depicts excellent Li storage properties at high current densities within a wider voltage window of 2-4.5 V, e.g., 93 mAh·g(-1) during the 300th cycle at a discharge current density of 5625 mA·g(-1) (~38.01 C). The wider operation voltage window can lead to increased theoretical capacity, e.g., 148 mAh·g(-1) between 3 and 4.5 V and 296 mAh·g(-1) between 2 and 4.5 V; (3) more importantly, it is found that the attachment of LMO onto graphene can help to reduce the dissolution of Mn(2+) into the electrolyte, as indicated by the inductively coupled plasma (ICP) measurements, and which is mainly attributed to the large specific surface area of the graphene sheets.

Selenium capped monolayer NbSe 2 for two-dimensional superconductivity studies

DOE PAGES

Onishi, Seita; Ugeda, Miguel M.; Zhang, Yi; ...

2016-08-01

Superconductivity in monolayer niobium diselenide (NbSe 2) on bilayer graphene is studied by electrical transport. Monolayer NbSe 2 is grown on bilayer graphene by molecular beam epitaxy and capped with a selenium film to avoid degradation in air. The selenium capped samples have T C = 1.9 K. In situ measurements down to 4 K in ultrahigh vacuum show that the effect of the selenium layer on the transport is negligible. Lastly, the superconducting transition and upper critical fields in air exposed and selenium capped samples are compared. Schematic of monolayer NbSe 2/bilayer graphene with selenium capping layer and electricalmore » contacts.« less

Composite laminate free-edge reinforcement with U-shaped caps. I - Stress analysis. II - Theoretical-experimental correlation

NASA Technical Reports Server (NTRS)

Howard, W. E.; Gossard, Terry, Jr.; Jones, Robert M.

1989-01-01

The present generalized plane-strain FEM analysis for the prediction of interlaminar normal stress reduction when a U-shaped cap is bonded to the edge of a composite laminate gives attention to the highly variable transverse stresses near the free edge, cap length and thickness, and a gap under the cap due to the manufacturing process. The load-transfer mechanism between cap and laminate is found to be strain-compatibility, rather than shear lag. In the second part of this work, the three-dimensional composite material failure criteria are used in a progressive laminate failure analysis to predict failure loads of laminates with different edge-cap designs; symmetric 11-layer graphite-epoxy laminates with a one-layer cap of kevlar-epoxy are shown to carry 130-140 percent greater loading than uncapped laminates, under static tensile and tension-tension fatigue loading.

North Polar Cap Layers and Ledges

NASA Image and Video Library

2016-08-24

At the edge of Mars' permanent North Polar cap, we see an exposure of the internal layers, each with a different mix of water ice, dust and dirt. These layers are believed to correspond to different climate conditions over the past tens of thousands of years. When we zoom in closer, we see that the distinct layers erode differently. Some are stronger and more resistant to erosion, others only weakly cemented. The strong layers form ledges. http://photojournal.jpl.nasa.gov/catalog/PIA21022

Islet-to-LMO stoichiometries control the function of transcription complexes that specify motor neuron and V2a interneuron identity

PubMed Central

Song, Mi-Ryoung; Sun, Yunfu; Bryson, Ami; Gill, Gordon N.; Evans, Sylvia M.; Pfaff, Samuel L.

2009-01-01

Summary LIM transcription factors bind to nuclear LIM interactor (Ldb/NLI/Clim) in specific ratios to form higher-order complexes that regulate gene expression. Here we examined how the dosage of LIM homeodomain proteins Isl1 and Isl2 and LIM-only protein Lmo4 influences the assembly and function of complexes involved in the generation of spinal motor neurons (MNs) and V2a interneurons (INs). Reducing the levels of Islet proteins using a graded series of mutations favored V2a IN differentiation at the expense of MN formation. Although LIM-only proteins (LMOs) are predicted to antagonize the function of Islet proteins, we found that the presence or absence of Lmo4 had little influence on MN or V2a IN specification. We did find, however, that the loss of MNs resulting from reduced Islet levels was rescued by eliminating Lmo4, unmasking a functional interaction between these proteins. Our findings demonstrate that MN and V2a IN fates are specified by distinct complexes that are sensitive to the relative stoichiometries of the constituent factors and we present a model to explain how LIM domain proteins modulate these complexes and, thereby, this binary-cell-fate decision. PMID:19666821

Enhancement of the Optoelectronic Properties of PEDOT: PSS-PbS Nanoparticles Composite Thin Films Through Nanoparticles' Capping Ligand Exchange

NASA Astrophysics Data System (ADS)

García-Gutiérrez, Diana F.; Hernández-Casillas, Laura P.; Sepúlveda-Guzmán, Selene; Vazquez-Rodriguez, Sofia; García-Gutiérrez, Domingo I.

2018-02-01

The influence of the capping ligand on nanoparticles' optical and electronic properties is a topic of great interest currently being investigated by several research groups in different countries. In the present study, PbS nanoparticles originally synthesized with oleic acid, myristic acid and hexanoic acid underwent a ligand exchange process to replace the original carboxylic acid for uc(l)-cysteine as the capping layer, and were thoroughly characterized by means of transmission electron microscopy and its related techniques, such as energy dispersive x-ray spectroscopy and scanning-transmission electron microscopy, and Fourier transform infrared, Raman and x-ray photoelectron spectroscopy. Afterwards, these PbS nanoparticles were dispersed into a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonic acid) (PEDOT:PSS) matrix to fabricate a composite thin film which displayed the optical absorption properties of the PbS nanoparticles and the electrical transport properties of the PEDOT:PSS matrix, in order to evaluate the impact of the nanoparticles' capping ligand on the optoelectronic properties of the fabricated composite thin films. Composite thin films with PbS nanoparticles showing uc(l)-cysteine as the capping layer displayed clear photoresponse and a threefold increment in their conductivities compared to pristine PEDOT:PSS. The properties of PEDOT:PSS, known as a hole transport layer in most organic photovoltaic devices, were enhanced by adding PbS nanoparticles with different capping ligands, producing a promising composite material for optoelectronic applications by proper selection of the nanoparticles' capping layer.

Protective capping and surface passivation of III-V nanowires by atomic layer deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dhaka, Veer, E-mail: veer.dhaka@aalto.fi; Perros, Alexander; Kakko, Joona-Pekko

2016-01-15

Low temperature (∼200 °C) grown atomic layer deposition (ALD) films of AlN, TiN, Al{sub 2}O{sub 3}, GaN, and TiO{sub 2} were tested for protective capping and surface passivation of bottom-up grown III-V (GaAs and InP) nanowires (NWs), and top-down fabricated InP nanopillars. For as-grown GaAs NWs, only the AlN material passivated the GaAs surface as measured by photoluminescence (PL) at low temperatures (15K), and the best passivation was achieved with a few monolayer thick (2Å) film. For InP NWs, the best passivation (∼2x enhancement in room-temperature PL) was achieved with a capping of 2nm thick Al{sub 2}O{sub 3}. All othermore » ALD capping layers resulted in a de-passivation effect and possible damage to the InP surface. Top-down fabricated InP nanopillars show similar passivation effects as InP NWs. In particular, capping with a 2 nm thick Al{sub 2}O{sub 3} layer increased the carrier decay time from 251 ps (as-etched nanopillars) to about 525 ps. Tests after six months ageing reveal that the capped nanostructures retain their optical properties. Overall, capping of GaAs and InP NWs with high-k dielectrics AlN and Al{sub 2}O{sub 3} provides moderate surface passivation as well as long term protection from oxidation and environmental attack.« less

Heat pipe with improved wick structures

DOEpatents

Benson, David A.; Robino, Charles V.; Palmer, David W.; Kravitz, Stanley H.

2000-01-01

An improved planar heat pipe wick structure having projections formed by micromachining processes. The projections form arrays of interlocking, semi-closed structures with multiple flow paths on the substrate. The projections also include overhanging caps at their tops to increase the capillary pumping action of the wick structure. The capped projections can be formed in stacked layers. Another layer of smaller, more closely spaced projections without caps can also be formed on the substrate in between the capped projections. Inexpensive materials such as Kovar can be used as substrates, and the projections can be formed by electrodepositing nickel through photoresist masks.

Conductive atomic force microscopy studies on the transformation of GeSi quantum dots to quantum rings.

PubMed

Zhang, S L; Xue, F; Wu, R; Cui, J; Jiang, Z M; Yang, X J

2009-04-01

Conductive atomic force microscopy has been employed to study the topography and conductance distribution of individual GeSi quantum dots (QDs) and quantum rings (QRs) during the transformation from QDs to QRs by depositing an Si capping layer on QDs. The current distribution changes significantly with the topographic transformation during the Si capping process. Without the capping layer, the QDs are dome-shaped and the conductance is higher at the ring region between the center and boundary than that at the center. After capping with 0.32 nm Si, the shape of the QDs changes to pyramidal and the current is higher at both the center and the arris. When the Si capping layer increases to 2 nm, QRs are formed and the current of individual QRs is higher at the rim than that at the central hole. By comparing the composition distributions obtained by scanning Auger microscopy and atomic force microscopy combined with selective chemical etching, the origin of the current distribution change is discussed.

High average power scaleable thin-disk laser

DOEpatents

Beach, Raymond J.; Honea, Eric C.; Bibeau, Camille; Payne, Stephen A.; Powell, Howard; Krupke, William F.; Sutton, Steven B.

2002-01-01

Using a thin disk laser gain element with an undoped cap layer enables the scaling of lasers to extremely high average output power values. Ordinarily, the power scaling of such thin disk lasers is limited by the deleterious effects of amplified spontaneous emission. By using an undoped cap layer diffusion bonded to the thin disk, the onset of amplified spontaneous emission does not occur as readily as if no cap layer is used, and much larger transverse thin disks can be effectively used as laser gain elements. This invention can be used as a high average power laser for material processing applications as well as for weapon and air defense applications.

Method of depositing an electrically conductive oxide buffer layer on a textured substrate and articles formed therefrom

DOEpatents

Paranthaman, M. Parans; Aytug, Tolga; Christen, David K.

2005-10-18

An article with an improved buffer layer architecture includes a substrate having a textured metal surface, and an electrically conductive lanthanum metal oxide epitaxial buffer layer on the surface of the substrate. The article can also include an epitaxial superconducting layer deposited on the epitaxial buffer layer. An epitaxial capping layer can be placed between the epitaxial buffer layer and the superconducting layer. A method for preparing an epitaxial article includes providing a substrate with a metal surface and depositing on the metal surface a lanthanum metal oxide epitaxial buffer layer. The method can further include depositing a superconducting layer on the epitaxial buffer layer, and depositing an epitaxial capping layer between the epitaxial buffer layer and the superconducting layer.

Method of depositing an electrically conductive oxide buffer layer on a textured substrate and articles formed therefrom

DOEpatents

Paranthaman, M. Parans; Aytug, Tolga; Christen, David K.

2003-09-09

An article with an improved buffer layer architecture includes a substrate having a textured metal surface, and an electrically conductive lanthanum metal oxide epitaxial buffer layer on the surface of the substrate. The article can also include an epitaxial superconducting layer deposited on the epitaxial buffer layer. An epitaxial capping layer can be placed between the epitaxial buffer layer and the superconducting layer. A method for preparing an epitaxial article includes providing a substrate with a metal surface and depositing on the metal surface a lanthanum metal oxide epitaxial buffer layer. The method can further include depositing a superconducting layer on the epitaxial buffer layer, and depositing an epitaxial capping layer between the epitaxial buffer layer and the superconducting layer.

Edible antimicrobial films based on microencapsulated lemongrass oil.

PubMed

Bustos C, Rubén O; Alberti R, Francesca V; Matiacevich, Silvia B

2016-01-01

Edible films and coatings have been proposed as viable alternatives for the preservation of fresh food such as fruit, meat, fish and cheese. They can be designed to contain natural antioxidants, vitamins and antimicrobials in order to extend shelf life of the product keeping the natural sensorial properties. Essential oils have been targeted as potential active principles for edible films and coatings given their well-recognized antioxidant, antimicrobial and sensory properties. In the present work, lemongrass oil (LMO) microcapsules were prepared by the emulsification-separation method using sodium caseinate as wall material. Microcapsules had an average size of 22 μm and contained over 51 % oil in their nucleus. The release kinetics of the LMO components was studied for both, microcapsules and microcapsule containing films. Experimental data for the controlled release of LMO components showed good correlation with Peppas and Weibull models. The effect of the alginate matrix on the release parameters of the mathematical models could be detected by the modification of the b constant of the Weibull equation which changed from 0.167 for the microcapsules to 0.351 for the films. Films containing LMO at concentrations of 1250, 2500 and 5000 ppm were able to inhibit growth of Escherichia coli ATCC 25922 and Listeria monocytogenes ISP 65-08 in liquid cultures. A possible future application of these films for shelf life extension of fresh food is discussed.

Differential expression and molecular characterisation of Lmo7, Myo1e, Sash1, and Mcoln2 genes in Btk-defective B-cells.

PubMed

Lindvall, Jessica M; Blomberg, K Emelie M; Wennborg, Anders; Smith, C I Edvard

2005-05-01

Bruton's tyrosine kinase is crucial for B-lymphocyte development. By the use of gene expression profiling, we have identified four expressed sequence tags among 38 potential Btk target genes, which have now been characterised. Bioinformatics tools including data mining of additional unpublished gene expression profiles, sequence verification of PCR products and qualitative RT-PCR were used. Stimulations targeting the B-cell receptor and the protein kinase C were used to activate whole B-cell splenocytes. Target genes were characterised as Lim domain only 7 (Lmo7); Myosin1e (Myo1e); SAM and SH3 domain containing 1 (Sash1); and Mucolipin2 (Mcoln2). Expression was found in cell lines of different origin and developmental stages as well as in whole B-cell splenocytes and Transitional type 1 (T1) splenic B-cells from wild type and Btk-defective mice, respectively. By the use of semi-quantitative RT-PCR we found Sash1 not to be expressed in the investigated haematopoietic cell lines, while transcripts were found in whole splenic B-cells from both wild type and Btk-defective mice, whereas Lmo7, Myo1e, and Mcoln2 were expressed in both B-cell lines and primary B-lymphocytes. Except for Lmo7, the transcript level was similarly affected by stimulation in control and Btk-defective cells.

Heavy metal multilayers for switching of magnetic unit via electrical current without magnetic field, method and applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Qinli; Li, Yufan; Chien, Chia-ling

Provided is an electric-current-controllable magnetic unit, including: a substrate, an electric-current channel disposed on the substrate, the electric-current channel including a composite heavy-metal multilayer comprising at least one heavy-metal; a capping layer disposed over the electric-current channel; and at least one ferromagnetic layer disposed between the electric-current channel and the capping layer.

Optimized capping layers for EUV multilayers

DOEpatents

Bajt, Sasa [Livermore, CA; Folta, James A [Livermore, CA; Spiller, Eberhard A [Livermore, CA

2004-08-24

A new capping multilayer structure for EUV-reflective Mo/Si multilayers consists of two layers: A top layer that protects the multilayer structure from the environment and a bottom layer that acts as a diffusion barrier between the top layer and the structure beneath. One embodiment combines a first layer of Ru with a second layer of B.sub.4 C. Another embodiment combines a first layer of Ru with a second layer of Mo. These embodiments have the additional advantage that the reflectivity is also enhanced. Ru has the best oxidation resistance of all materials investigated so far. B.sub.4 C is an excellent barrier against silicide formation while the silicide layer formed at the Si boundary is well controlled.

Interfacial stability of CoSi2/Si structures grown by molecular beam epitaxy

NASA Technical Reports Server (NTRS)

George, T.; Fathauer, R. W.

1992-01-01

The stability of CoSi2/Si interfaces was examined in this study using columnar silicide structures grown on (111) Si substrates. In the first set of experiments, Co and Si were codeposited using MBE at 800 C and the resulting columnar silicide layer was capped by epitaxial Si. Deposition of Co on the surface of the Si capping layer at 800 C results in the growth of the buried silicide columns. The buried columns grow by subsurface diffusion of the deposited Co, suppressing the formation of surface islands of CoSi2. The column sidewalls appear to be less stable than the top and bottom interfaces, resulting in preferential lateral growth and ultimately in the coalescence of the columns to form a continuous buried CoSi2 layer. In the second set of experiments, annealing of a 250 nm-thick buried columnar layer at 1000 C under a 100 nm-thick Si capping layer results in the formation of a surface layer of CoSi2 with a reduction in the sizes of the CoSi2 columns. For a sample having a thicker Si capping layer the annealing leads to Ostwald ripening producing buried equiaxed columns. The high CoSi2/Si interfacial strain could provide the driving force for the observed behavior of the buried columns under high-temperature annealing.

Sensitivity of diamond-capped impedance transducer to Tröger's base derivative.

PubMed

Stehlik, Stepan; Izak, Tibor; Kromka, Alexander; Dolenský, Bohumil; Havlík, Martin; Rezek, Bohuslav

2012-08-01

Sensitivity of an intrinsic nanocrystalline diamond (NCD) layer to naphthalene Tröger's base derivative decorated with pyrrole groups (TBPyr) was characterized by impedance spectroscopy. The transducer was made of Au interdigitated electrodes (IDE) with 50 μm spacing on alumina substrate which were capped with the NCD layer. The NCD-capped transducer with H-termination was able to electrically distinguish TBPyr molecules (the change of surface resistance within 30-60 kΩ) adsorbed from methanol in concentrations of 0.04 mg/mL to 40 mg/mL. An exponential decay of the surface resistance with time was observed and attributed to the readsorption of air moisture after methanol evaporation. After surface oxidation the NCD cap layer did not show any leakage due to NCD grain boundaries. We analyzed electronic transport in the transducer and propose a model for the sensing mechanism based on surface ion replacement.

Effects of a capping oxide layer on polycrystalline-silicon thin-film transistors fabricated by continuous-wave laser crystallization

NASA Astrophysics Data System (ADS)

Li, Yi-Shao; Wu, Chun-Yi; Chou, Chia-Hsin; Liao, Chan-Yu; Chuang, Kai-Chi; Luo, Jun-Dao; Li, Wei-Shuo; Cheng, Huang-Chung

2018-06-01

A tetraethyl-orthosilicate (TEOS) capping oxide was deposited by low-pressure chemical vapor deposition (LPCVD) on a 200-nm-thick amorphous Si (a-Si) film as a heat reservoir to improve the crystallinity and surface roughness of polycrystalline silicon (poly-Si) formed by continuous-wave laser crystallization (CLC). The effects of four thicknesses of the capping oxide layer to satisfy an antireflection condition, namely, 90, 270, 450, and 630 nm, were investigated. The largest poly-Si grain size of 2.5 × 20 µm2 could be achieved using a capping oxide layer with an optimal thickness of 450 nm. Moreover, poly-Si nanorod (NR) thin-film transistors (TFTs) fabricated using the aforementioned technique exhibited a superior electron field-effect mobility of 1093.3 cm2 V‑1 s‑1 and an on/off current ratio of 2.53 × 109.

Optimization design on breakdown voltage of AlGaN/GaN high-electron mobility transistor

NASA Astrophysics Data System (ADS)

Yang, Liu; Changchun, Chai; Chunlei, Shi; Qingyang, Fan; Yuqian, Liu

2016-12-01

Simulations are carried out to explore the possibility of achieving high breakdown voltage of GaN HEMT (high-electron mobility transistor). GaN cap layers with gradual increase in the doping concentration from 2 × 1016 to 5 × 1019 cm-3 of N-type and P-type cap are investigated, respectively. Simulation results show that HEMT with P-doped GaN cap layer shows more potential to achieve higher breakdown voltage than N-doped GaN cap layer under the same doping concentration. This is because the ionized net negative space charges in P-GaN cap layer could modulate the surface electric field which makes more contribution to RESURF effect. Furthermore, a novel GaN/AlGaN/GaN HEMT with P-doped GaN buried layer in GaN buffer between gate and drain electrode is proposed. It shows enhanced performance. The breakdown voltage of the proposed structure is 640 V which is increased by 12% in comparison to UID (un-intentionally doped) GaN/AlGaN/GaN HEMT. We calculated and analyzed the distribution of electrons' density. It is found that the depleted region is wider and electric field maximum value is induced at the left edge of buried layer. So the novel structure with P-doped GaN buried layer embedded in GaN buffer has the better improving characteristics of the power devices. Project supported by the National Basic Research Program of China (No. 2014CB339900) and the Open Fund of Key Laboratory of Complex Electromagnetic Environment Science and Technology, China Academy of Engineering Physics (No. 2015-0214.XY.K).

Application of a simplified calculation for full-wave microtremor H/ V spectral ratio based on the diffuse field approximation to identify underground velocity structures

NASA Astrophysics Data System (ADS)

Wu, Hao; Masaki, Kazuaki; Irikura, Kojiro; Sánchez-Sesma, Francisco José

2017-12-01

Under the diffuse field approximation, the full-wave (FW) microtremor H/ V spectral ratio ( H/ V) is modeled as the square root of the ratio of the sum of imaginary parts of the Green's function of the horizontal components to that of the vertical one. For a given layered medium, the FW H/ V can be well approximated with only surface waves (SW) H/ V of the "cap-layered" medium which consists of the given layered medium and a new larger velocity half-space (cap layer) at large depth. Because the contribution of surface waves can be simply obtained by the residue theorem, the computation of SW H/ V of cap-layered medium is faster than that of FW H/ V evaluated by discrete wavenumber method and contour integration method. The simplified computation of SW H/ V was then applied to identify the underground velocity structures at six KiK-net strong-motion stations. The inverted underground velocity structures were used to evaluate FW H/ Vs which were consistent with the SW H/ Vs of corresponding cap-layered media. The previous study on surface waves H/ Vs proposed with the distributed surface sources assumption and a fixed Rayleigh-to-Love waves amplitude ratio for horizontal motions showed a good agreement with the SW H/ Vs of our study. The consistency between observed and theoretical spectral ratios, such as the earthquake motions of H/ V spectral ratio and spectral ratio of horizontal motions between surface and bottom of borehole, indicated that the underground velocity structures identified from SW H/ V of cap-layered medium were well resolved by the new method.[Figure not available: see fulltext.

High temperature superconductor step-edge Josephson junctions using Ti-Ca-Ba-Cu-O

DOEpatents

Ginley, David S.; Hietala, Vincent M.; Hohenwarter, Gert K. G.; Martens, Jon S.; Plut, Thomas A.; Tigges, Chris P.; Vawter, Gregory A.; Zipperian, Thomas E.

1994-10-25

A process for formulating non-hysteretic and hysteretic Josephson junctions using HTS materials which results in junctions having the ability to operate at high temperatures while maintaining high uniformity and quality. The non-hysteretic Josephson junction is formed by step-etching a LaAlO.sub.3 crystal substrate and then depositing a thin film of TlCaBaCuO on the substrate, covering the step, and forming a grain boundary at the step and a subsequent Josephson junction. Once the non-hysteretic junction is formed the next step to form the hysteretic Josephson junction is to add capacitance to the system. In the current embodiment, this is accomplished by adding a thin dielectric layer, LaA1O.sub.3, followed by a cap layer of a normal metal where the cap layer is formed by first depositing a thin layer of titanium (Ti) followed by a layer of gold (Au). The dielectric layer and the normal metal cap are patterned to the desired geometry.

The role of temperature ramp-up time before barrier layer growth in optical and structural properties of InGaN/GaN multi-quantum wells

NASA Astrophysics Data System (ADS)

Xing, Yao; Zhao, Degang; Jiang, Desheng; Liu, Zongshun; Zhu, Jianjun; Chen, Ping; Yang, Jing; Liu, Wei; Liang, Feng; Liu, Shuangtao; Zhang, Liqun; Wang, Wenjie; Li, Mo; Zhang, Yuantao; Du, Guotong

2018-05-01

In InGaN/GaN multi-quantum wells (MQWs), a low temperature cap (LT-cap) layer is grown between the InGaN well layer and low temperature GaN barrier layer. During the growth, a temperature ramp-up and ramp-down process is added between LT-cap and barrier layer growth. The effect of temperature ramp-up time duration on structural and optical properties of quantum wells is studied. It is found that as the ramp-up time increases, the Indium floating layer on the top of the well layer can be diminished effectively, leading to a better interface quality between well and barrier layers, and the carrier localization effect is enhanced, thereby the internal quantum efficiency (IQE) of QWs increases surprisingly. However, if the ramp-up time is too long, the carrier localization effect is weaker, which may increase the probabilities of carriers to meet with nonradiative recombination centers. Meanwhile, more nonradiative recombination centers will be introduced into well layers due to the indium evaporation. Both of them will lead to a reduction of internal quantum efficiency (IQE) of MQWs.

Assimilation of COST 716 Near-Real Time GPS data in the nonhydrostatic limited area model used at MeteoSwiss

NASA Astrophysics Data System (ADS)

Guerova, G.; Bettems, J.-M.; Brockmann, E.; Matzler, Ch.

2006-01-01

Application of the GPS derived water vapor into Numerical Weather Prediction (NWP) models is one of the focuses of the COST Action 716 “Exploitation of Ground based GPS for climate and numerical weather prediction applications”. For this purpose the GPS data covering Europe have been collected within the Near-Real Time (NRT) demonstration project and provided for Observing System Experiments (OSE). For the experiments presented in this manuscript the operational NWP system of MeteoSwiss is used. The limited area nonhydrostatic aLpine Model (aLMo) of MeteoSwiss covers most of western Europe, has a horizontal resolution of 7 km, 45 layers in the vertical, and uses a data assimilation scheme based on the Newtonian relaxation (nudging) method. In total 17 days analyses and two 30 hours daily forecasts have been computed, with 100 GPS sites assimilated for three selected periods in autumn 2001, winter and summer 2002. It is to be noted that only in the last period data from 10 french sites, i.e. west of Switzerland are assimilated. The GPS NRT data quality has been compared with the Post-Processed data. Agreement within 3 mm level Zenith Total Delay bias and 8 mm standard deviation was found, corresponding to an Integrated Water Vapor (IWV) bias below 0.5 kg/m2. Most of the NRT data over aLMo domain are available within a prescribed time window of 1 h 45 min. In the nudging process the NRT data are successfully used by the model to correct the IWV deficiencies present in the reference analysis; stronger forcing with a shorter time scale could be however recommended. Comparing the GPS derived IWV with radiosonde observations, a dry radiosonde bias has been found over northern Italy. Through GPS data assimilation the aLMo analysis bias and standard deviation in the diurnal cycle has been reduced. The negative bias of 0.64 kg/m2 in the reference analysis has been reduced to 0.34 kg/m2 in GPS analysis. However, the diurnal cycle statistic from the forecast does show the characteristic negative bias only slightly reduced starting with the GPS analysis. The GPS IWV impact on aLMo is large in June 2002 and moderate in September 2001 OSE. January OSE is inconclusive due to inconsistent use of humidity data below the freezing point. In June 2002 OSE, a substantial IWV impact is seen up to the end of the forecast. Over Switzerland the dry bias in the reference analysis has been successfully corrected and the 2 m temperature and dew point have been slightly improved over the whole aLMo domain. The subjective verification of precipitation against radar data in autumn 2001 and summer 2002 gives mixed results. In the forecast the impact is limited to the first six hours and to strong precipitation events. A missing precipitation pattern has been recovered via GPS assimilation in June 20 2002 forecast. A negative impact on precipitation analysis on June 23 has been observed. The future operational use of GPS will depend on data availability; European GPS networks belong mainly to the geodetic community. A further increase of GPS network density in southern Europe is welcome. The GPS derived gradient and Slant Path estimates could possibly improve efficiency of IWV assimilation via the nudging technique.

Effect of same-temperature GaN cap layer on the InGaN/GaN multiquantum well of green light-emitting diode on silicon substrate.

PubMed

Zheng, Changda; Wang, Li; Mo, Chunlan; Fang, Wenqing; Jiang, Fengyi

2013-01-01

GaN green LED was grown on Si (111) substrate by MOCVD. To enhance the quality of InGaN/GaN MQWs, same-temperature (ST) GaN protection layers with different thickness of 8 Å, 15 Å, and 30 Å were induced after the InGaN quantum wells (QWs) layer. Results show that a relative thicker cap layer is benefit to get InGaN QWs with higher In percent at fixed well temperature and obtain better QW/QB interface. As the cap thickness increases, the indium distribution becomes homogeneous as verified by fluorescence microscope (FLM). The interface of MQWs turns to be abrupt from XRD analysis. The intensity of photoluminescence (PL) spectrum is increased and the FWHM becomes narrow.

Development of dental composites with reactive fillers that promote precipitation of antibacterial-hydroxyapatite layers.

PubMed

Aljabo, Anas; Abou Neel, Ensanya A; Knowles, Jonathan C; Young, Anne M

2016-03-01

The study aim was to develop light-curable, high strength dental composites that would release calcium phosphate and chlorhexidine (CHX) but additionally promote surface hydroxyapatite/CHX co-precipitation in simulated body fluid (SBF). 80 wt.% urethane dimethacrylate based liquid was mixed with glass fillers containing 10 wt.% CHX and 0, 10, 20 or 40 wt.% reactive mono- and tricalcium phosphate (CaP). Surface hydroxyapatite layer thickness/coverage from SEM images, Ca/Si ratio from EDX and hydroxyapatite Raman peak intensities were all proportional to both time in SBF and CaP wt.% in the filler. Hydroxyapatite was, however, difficult to detect by XRD until 4 weeks. XRD peak width and SEM images suggested this was due to the very small size (~10 nm) of the hydroxyapatite crystallites. Precipitate mass at 12 weeks was 22 wt.% of the sample CaP total mass irrespective of CaP wt.% and up to 7 wt.% of the specimen. Early diffusion controlled CHX release, assessed by UV spectrometry, was proportional to CaP and twice as fast in water compared with SBF. After 1 week, CHX continued to diffuse into water but in SBF, became entrapped within the precipitating hydroxyapatite layer. At 12 weeks CHX formed 5 to 15% of the HA layer with 10 to 40 wt.% CaP respectively. Despite linear decline of strength and modulus in 4 weeks from 160 to 101 MPa and 4 to 2.4 GPa, respectively, upon raising CaP content, all values were still within the range expected for commercial composites. The high strength, hydroxyapatite precipitation and surface antibacterial accumulation should reduce tooth restoration failure due to fracture, aid demineralised dentine repair and prevent subsurface carious disease respectively. Copyright © 2015 The Authors. Published by Elsevier B.V. All rights reserved.

A GCM Recent History of Northern Martian Polar Layered Deposits: Contribution from Past Equatorial Ice Reservoirs

NASA Technical Reports Server (NTRS)

Levrard, B.; Laskar, J.; Montmessin, F.; Forget, F.

2005-01-01

Polar layered deposits are exposed in the walls of the troughs cutting the north polar cap of Mars. They consist of alternating ice and dust layers or layers of an ice-dust mixture with varying proportions and are found throughout the cap. Layers thickness ranges from meters to several tens of meters with an approximately 30 meter dominant wavelength. Although their formation processes is not known, they are presumed to reflect changes in ice and dust stability over orbital and axial variations. Intensive 3-D LMD GCM simulations of the martian water cycle have been thus performed to determine the annual rates of exchange of surface ice between the northern cap and tropical areas for a wide range of obliquity and orbital parameters values.These rates have been employed to reconstruct an history of the northern cap and test simple models of dust-ice layers formation over the last 10 Ma orbital variations. We use the 3-D water cycle model simulated by the 3-D LMD GCM with an intermediate grid resolution (7.5 longitude x 5.625 latitude) and 25 vertical levels. The dust opacity is constant and set to 0,15. No exchange of ice with regolith is allowed. The evolution of the northern cap over obliquity and orbital changes (eccentricity, Longitude of perihelion) has been recently described with this model. High summer insolation favors transfer of ice from the northern pole to the Tharsis and Olympus Montes, while at low obliquity, unstable equatorial ice is redeposited in high-latitude and polar areas of both hemisphere. The disappearance of the equatorial ice reservoir leads to a poleward recession of icy high latitude reservoirs, providing an additional source for the cap accumulation during each obliquity or orbital cycle. Furthering the efforts, a quantitative evolution of ice reservoirs is here investigated for various astronomical conditions.

Volatile element loss during planetary magma ocean phases

NASA Astrophysics Data System (ADS)

Dhaliwal, Jasmeet K.; Day, James M. D.; Moynier, Frédéric

2018-01-01

Moderately volatile elements (MVE) are key tracers of volatile depletion in planetary bodies. Zinc is an especially useful MVE because of its generally elevated abundances in planetary basalts, relative to other MVE, and limited evidence for mass-dependent isotopic fractionation under high-temperature igneous processes. Compared with terrestrial basalts, which have δ66Zn values (per mille deviation of the 66Zn/64Zn ratio from the JMC-Lyon standard) similar to some chondrite meteorites (∼+0.3‰), lunar mare basalts yield a mean δ66Zn value of +1.4 ± 0.5‰ (2 st. dev.). Furthermore, mare basalts have average Zn concentrations ∼50 times lower than in typical terrestrial basaltic rocks. Late-stage lunar magmatic products, including ferroan anorthosite, Mg- and Alkali-suite rocks have even higher δ66Zn values (+3 to +6‰). Differences in Zn abundance and isotopic compositions between lunar and terrestrial rocks have previously been interpreted to reflect evaporative loss of Zn, either during the Earth-Moon forming Giant Impact, or in a lunar magma ocean (LMO) phase. To explore the mechanisms and processes under which volatile element loss may have occurred during a LMO phase, we developed models of Zn isotopic fractionation that are generally applicable to planetary magma oceans. Our objective was to identify conditions that would yield a δ66Zn signature of ∼+1.4‰ within the lunar mantle. For the sake of simplicity, we neglect possible Zn isotopic fractionation during the Giant Impact, and assumed a starting composition equal to the composition of the present-day terrestrial mantle, assuming both the Earth and Moon had zinc 'consanguinity' following their formation. We developed two models: the first simulates evaporative fractionation of Zn only prior to LMO mixing and crystallization; the second simulates continued evaporative fractionation of Zn that persists until ∼75% LMO crystallization. The first model yields a relatively homogenous bulk solid LMO δ66Zn value, while the second results in a stratification of δ66Zn values within the LMO sequence. Loss and/or isolation mechanisms for volatiles are critical to these models; hydrodynamic escape was not a dominant process, but loss of a nascent lunar atmosphere or separation of condensates into a proto-lunar crust are possible mechanisms by which volatiles could be separated from the lunar interior. The results do not preclude models that suggest a lunar volatile depletion episode related to the Giant Impact. Conversely, LMO models for volatile loss do not require loss of volatiles prior to lunar formation. Outgassing during planetary magma ocean phases likely played a profound role in setting the volatile inventories of planets, particularly for low mass bodies that experienced the greatest volatile loss. In turn, our results suggest that the initial compositions of planets that accreted from smaller, highly differentiated planetesimals were likely to be severely volatile depleted.

Effective control of modified palygorskite to NH4+-N release from sediment.

PubMed

Chen, Lei; Zheng, Tianyuan; Zhang, Junjie; Liu, Jie; Zheng, Xilai

2014-01-01

Sediment capping is an in situ treatment technology that can effectively restrain nutrient and pollutant release from the sediment in lakes and reservoirs. Research on sediment capping has focused on the search for effective, non-polluting and affordable capping materials. The efficiency and mechanism of sediment capping with modified palygorskite in preventing sediment ammonia nitrogen (NH4+-N) release to surface water were investigated through a series of batch and sediment capping experiments. Purified palygorskite and different types of modified palygorskite (i.e. heated, acid-modified and NaCI-modified palygorskite) were used in this investigation. Factors affecting control efficiency, including the temperature, thickness and grain size of the capping layer, were also analysed. The batch tests showed that the adsorption of NH4+-N on modified palygorskite achieved an equilibration in the initial 45 min, and the adsorption isotherm followed the Freundlich equation. Sediment capping experiments showed that compared with non-capped condition, covering the sediment with modified palygorskite and sand both inhibited NH4+-N release to the overlying water. Given its excellent chemical stability and strong adsorption, heated palygorskite, which has a NH4+-N release inhibition ratio of 41.3%, is a more effective sediment capping material compared with sand. The controlling effectiveness of the modified palygorskite increases with thicker capping layer, lower temperature and smaller grain size of the capping material.

The effect of perfluorination on the aromaticity of benzene and heterocyclic six-membered rings.

PubMed

Wu, Judy I; Pühlhofer, Frank G; Schleyer, Paul von Ragué; Puchta, Ralph; Kiran, Boggavarapu; Mauksch, Michael; Hommes, Nico J R van Eikema; Alkorta, Ibon; Elguero, José

2009-06-18

Despite having six highly electronegative F's, perfluorobenzene C(6)F(6) is as aromatic as benzene. Ab initio block-localized wave function (BLW) computations reveal that both C(6)F(6) and benzene have essentially the same extra cyclic resonance energies (ECREs). Localized molecular orbital (LMO)-nucleus-independent chemical shifts (NICS) grids demonstrates that the F's induce only local paratropic contributions that are not related to aromaticity. Thus, all of the fluorinated benzenes (C(6)F(n)H((6-n)), n = 1-6) have similar ring-LMO-NICS(pi zz) values. However, 1,3-difluorobenzene 2b and 1,3,5-trifluorobenzene 3c are slightly less aromatic than their isomers due to a greater degree of ring charge alternation. Isoelectronic C(5)H(5)Y heterocycles (Y = BH(-), N, NH(+)) are as aromatic as benzene, based on their ring-LMO-NICS(pi zz) and ECRE values, unless extremely electronegative heteroatoms (e.g., Y = O(+)) are involved.

P-type doping of GaN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, Raechelle Kimberly

2000-04-01

After implantation of As, As + Be, and As + Ga into GaN and annealing for short durations at temperatures as high as 1500 C, the GaN films remained highly resistive. It was apparent from c-RBS studies that although implantation damage did not create an amorphous layer in the GaN film, annealing at 1500 C did not provide enough energy to completely recover the radiation damage. Disorder recovered significantly after annealing at temperatures up to 1500 C, but not completely. From SIMS analysis, oxygen contamination in the AIN capping layer causes oxygen diffusion into the GaN film above 1400 C.more » The sapphire substrate (A1203) also decomposed and oxygen penetrated into the backside of the GaN layer above 1400 C. To prevent donor-like oxygen impurities from the capping layer and the substrate from contaminating the GaN film and compensating acceptors, post-implantation annealing should be done at temperatures below 1500 C. Oxygen in the cap could be reduced by growing the AIN cap on the GaN layer after the GaN growth run or by depositing the AIN layer in a ultra high vacuum (UHV) system post-growth to minimize residual oxygen and water contamination. With longer annealing times at 1400 C or at higher temperatures with a higher quality AIN, the implantation drainage may fully recover.« less

Serine/threonine protein kinase PrkA of the human pathogen Listeria monocytogenes: biochemical characterization and identification of interacting partners through proteomic approaches.

PubMed

Lima, Analía; Durán, Rosario; Schujman, Gustavo Enrique; Marchissio, María Julia; Portela, María Magdalena; Obal, Gonzalo; Pritsch, Otto; de Mendoza, Diego; Cerveñansky, Carlos

2011-08-24

Listeria monocytogenes is the causative agent of listeriosis, a very serious food-borne human disease. The analysis of the proteins coded by the L. monocytogenes genome reveals the presence of two eukaryotic-type Ser/Thr-kinases (lmo1820 and lmo0618) and a Ser/Thr-phosphatase (lmo1821). Protein phosphorylation regulates enzyme activities and protein interactions participating in physiological and pathophysiological processes in bacterial diseases. However in the case of L. monocytogenes there is scarce information about biochemical properties of these enzymes, as well as the physiological processes that they modulate. In the present work the catalytic domain of the protein coded by lmo1820 was produced as a functional His(6)-tagged Ser/Thr-kinase, and was denominated PrkA. PrkA was able to autophosphorylate specific Thr residues within its activation loop sequence. A similar autophosphorylation pattern was previously reported for Ser/Thr-kinases from related prokaryotes, whose role in kinase activity and substrate recruitment was demonstrated. We studied the kinase interactome using affinity chromatography and proteomic approaches. We identified 62 proteins that interact, either directly or indirectly, with the catalytic domain of PrkA, including proteins that participate in carbohydrates metabolism, cell wall metabolism and protein synthesis. Our results suggest that PrkA could be involved in the regulation of a variety of fundamental biological processes. Copyright © 2011 Elsevier B.V. All rights reserved.

Evidence for a "Wet" Early Moon

NASA Technical Reports Server (NTRS)

Hui, Hejiu; Peslier, Anne H.; Zhang, Youxue; Neal, Clive R.

2013-01-01

The Moon was thought to have lost its volatiles during impact(s) of a Mars-size planetesimal with the proto Earth [1] and during degassing of an early planet-wide magma ocean [2]. This view of an anhydrous Moon, however, has been challenged by recent discoveries of water on its surface [3-5] and in lunar volcanics [6-10] and regoliths [11]. Indigenous water is suggested to be heterogeneously distributed in the lunar interior and some parts of lunar mantle may contain as much water as Earth's upper mantle [6,10]. This water is thought to have been brought in part through solar wind implantation [3-5,8,11] and meteorite/cometary impacts [3,4,8,12] after the formation of the primary crust. Here we measured water in primary products of the Lunar Magma Ocean (LMO) thereby by-passing the processes of later addition of water to the Moon through impact events or during mantle overturn as suggested by previous studies (e.g., [8,12]). So far, ferroan anorthosite (FAN) is the only available lithology that is believed to be a primary product of the LMO [2]. It is generally accepted that plagioclase, after crystallization, floated in the LMO and formed FAN as the original crust [2]. Therefore, any indigenous water preserved in FAN was partitioned from the LMO. These data can be used to estimate the water content of the magma ocean at the time of plagioclase crystallization, as well as that of the mare magma source regions.

Effect of Same-Temperature GaN Cap Layer on the InGaN/GaN Multiquantum Well of Green Light-Emitting Diode on Silicon Substrate

PubMed Central

Zheng, Changda; Wang, Li; Mo, Chunlan; Fang, Wenqing; Jiang, Fengyi

2013-01-01

GaN green LED was grown on Si (111) substrate by MOCVD. To enhance the quality of InGaN/GaN MQWs, same-temperature (ST) GaN protection layers with different thickness of 8 Å, 15 Å, and 30 Å were induced after the InGaN quantum wells (QWs) layer. Results show that a relative thicker cap layer is benefit to get InGaN QWs with higher In percent at fixed well temperature and obtain better QW/QB interface. As the cap thickness increases, the indium distribution becomes homogeneous as verified by fluorescence microscope (FLM). The interface of MQWs turns to be abrupt from XRD analysis. The intensity of photoluminescence (PL) spectrum is increased and the FWHM becomes narrow. PMID:24369453

Conversion of Nuclear Waste into Nuclear Waste Glass: Experimental Investigation and Mathematical Modeling

DOE PAGES

Hrma, Pavel

2014-12-18

The melter feed, slurry, or calcine charged on the top of a pool of molten glass forms a floating layer of reacting material called the cold cap. Between the cold-cap top, which is covered with boiling slurry, and its bottom, where bubbles separate it from molten glass, the temperature changes by up to 1000 K. The processes that occur over this temperature interval within the cold cap include liberation of gases, conduction and consumption of heat, dissolution of quartz particles, formation and dissolution of intermediate crystalline phases, and generation of foam and gas cavities. These processes have been investigated usingmore » thermal analyses, optical and electronic microscopies, x-ray diffraction, as well as other techniques. Properties of the reacting feed, such as heat conductivity and density, were measured as functions of temperature. Investigating the structure of quenched cold caps produced in a laboratory-scale melter complemented the crucible studies. The cold cap consists of two main layers. The top layer contains solid particles dissolving in the glass-forming melt and open pores through which gases are escaping. The bottom layer contains bubbly melt or foam where bubbles coalesce into larger cavities that move sideways and release the gas to the atmosphere. The feed-to-glass conversion became sufficiently understood for representing the cold-cap processes via mathematical models. These models, which comprise heat transfer, mass transfer, and reaction kinetics models, have been developed with the final goal to relate feed parameters to the rate of glass melting.« less

Extended HFSE systematics of Apollo samples - wrenching further Secrets from the Lunar Mantle

NASA Astrophysics Data System (ADS)

Thiemens, M. M.; Sprung, P.; Munker, C.

2016-12-01

As Earth's intimate companion, the Moon provides a close extraterrestrial view on planetary differentiation. In turn, investigating chemical and isotopic compositions of lunar rocks for traces of a putative crystallizing Lunar Magma Ocean (LMO) provides a better understanding of the evolution and differentiation of infant planetary bodies.We expand on high-precision extended High Field Strength Element (HFSE) observations of Münker [1]. In detail, we investigate if the HFSE systematics of low- and high- Ti basalts, KREEPy basalts and breccias, soils, and ferroan anorthosites (FAN) are consistent with their formation from the LMO (FAN, KREEP) or mantle sources comprising mixtures of primary LMO products [2] (mare basalts). Of particular interest is the recently discovered dependence of HFSE partitioning on the Ti-concentration of co-existing melts [3] and that of W partitioning on oxygen fugacity [3,4].Our data form a positively correlated array in Zr/Hf vs. Nb/Ta space, similar to previous high-precision [1] but unlike lower-precision data. The HFSE systematics of different rock types from the Apollo missions mostly form distinct groups. High-Ti and some Apollo 12 low-Ti mare basalts form the lower end of the array, KREEPy samples its upper end. Low Zr/Nb in most high-Ti mare basalts and the globally highest Hf/W confirm involvement of Ti-rich-oxide-bearing cumulates in high-Ti formation [e.g., 1,2]. No global lunar trends exist for Hf/W vs. Zr/Nb. Overall, the composition of KREEPy samples agrees reasonably well with model KREEP-compositions assuming a LMO below IW-1 [1,4].Clearly distinct groupings observed for the various rock types and the lack of a global trend in Hf/W vs. Zr/Nb calls for melting of distinct ultramafic sources [1]. The HFSE systematics of Apollo rocks tend to support a LMO scenario, setting the stage for more detailed petrogenetic modeling. Initial modeling suggests that the lunar mantle must possess residual metal to reconcile the HFSE systematics of Apollo rocks within an LMO-scenario, providing an alternative explanation for the very low abundances of HSE in the lunar crust [5].[1] Münker, C. (2010) GCA 74, 7340-7361. [2] Snyder et al. (1992) GCA 56, 3809-3823. [3] Leitzke et al. (in press) Chem. Geol. [4] Fonseca et al. (2014) EPSL 404, 1-13. [5] Day & Walker (2015) EPSL 423, 114-124

High temperature superconductor step-edge Josephson junctions using Ti-Ca-Ba-Cu-O

DOEpatents

Ginley, D.S.; Hietala, V.M.; Hohenwarter, G.K.G.; Martens, J.S.; Plut, T.A.; Tigges, C.P.; Vawter, G.A.; Zipperian, T.E.

1994-10-25

A process is disclosed for formulating non-hysteretic and hysteretic Josephson junctions using HTS materials which results in junctions having the ability to operate at high temperatures while maintaining high uniformity and quality. The non-hysteretic Josephson junction is formed by step-etching a LaAlO[sub 3] crystal substrate and then depositing a thin film of TlCaBaCuO on the substrate, covering the step, and forming a grain boundary at the step and a subsequent Josephson junction. Once the non-hysteretic junction is formed the next step to form the hysteretic Josephson junction is to add capacitance to the system. In the current embodiment, this is accomplished by adding a thin dielectric layer, LaA1O[sub 3], followed by a cap layer of a normal metal where the cap layer is formed by first depositing a thin layer of titanium (Ti) followed by a layer of gold (Au). The dielectric layer and the normal metal cap are patterned to the desired geometry. 8 figs.

Effects of Natural Organic Matter on PCB-Activated Carbon Sorption Kinetics: Implications for Sediment Capping Applications

EPA Science Inventory

In-situ capping of polychlorinated biphenyl (PCB) contaminated sediments with layers of sorbents such as activated carbon has been proposed, but several technical questions remain regarding long-term effectiveness. An activated carbon amended sediment cap was mimicked in laborat...

Ultraviolet weathering of HDPE/wood-flour composites coextruded with a clear HDPE cap layer

Treesearch

Laurent M. Matuana; Shan Jin; Nicole M. Stark

2011-01-01

This study examined the effect coextruding a clear HDPE cap layer onto HDPE/wood-flour composites has on the discoloration of coextruded composites exposed to accelerated UV tests. Chroma meter, FTIRATR, XPS, SEM, and UV vis measurements accounted for the analysis of discoloration, functional groups, and degree of oxidation of both uncapped (control) and coextruded...

Iron layer-dependent surface-enhanced raman scattering of hierarchical nanocap arrays

NASA Astrophysics Data System (ADS)

Chen, Lei; Sun, Huanhuan; Zhao, Yue; Gao, Renxian; Wang, Yaxin; Liu, Yang; Zhang, Yongjun; Hua, Zhong; Yang, Jinghai

2017-11-01

In this report, we fabricated the multi-layer Ag/Fe/Ag sandwich cap-shaped films on monolayer non-closed packed (ncp) polystyrene colloidal particle (PSCP) templates through a layer-by-layer (LBL) depositing method. This research focused on the surface-enhanced Raman scattering (SERS) effect of the thickness of the deposited Fe film which was controlled by the sputtering time. The SERS intensities were increased firstly, and then decreased as the thickness of Fe layer grows gradually, which is attributed to the charge transition from the Fermi level of the Ag NPs to Fe layer. The use of multi-layer Ag/Fe/Ag sandwich cap-shaped films enables us to evaluate the contribution of surface plasmon resonance and charge distribution between Ag and Fe to SERS enhancement. Our work introduced a novel system (Ag/Fe/Ag) for high performance SERS and extended the SERS application of Fe. Furthermore, we have designed the Ag/Fe/Ag SERS-active substrate as the immunoassay chip for quantitative determination of AFP-L3 which is the biomarker of hepatocellular carcinoma (HCC). The proposed research demonstrates that the SERS substrates with Ag/Fe/Ag sandwich cap-shaped arrays have a high sensitivity for bioassay.

Comparison of 120- and 140-μm SMILE Cap Thickness Results in Eyes With Thick Corneas.

PubMed

Liu, Manli; Zhou, Yugui; Wu, Xianghua; Ye, Tiantian; Liu, Quan

2016-10-01

To evaluate clinical outcomes after small incision lenticule extraction (SMILE) with different cap thicknesses in thick corneas. Forty patients with central corneal thickness of more than 560 μm were recruited in this prospective, randomized, masked, paired-eye study. Patients were randomized to receive SMILE with a 120-μm cap thickness in 1 eye and 140-μm cap thickness in the other. Uncorrected and corrected distance visual acuity (CDVA), contrast sensitivity (CS), higher-order aberrations (HOAs), and morphologic modifications of corneal architecture were measured during the 3-month follow-up period. Postoperative refractive outcomes, visual outcomes, CS, and the changes in HOAs were similar between both groups. The persistence of brightly reflective particles in the corneal interface layer was 1388.6 ± 219.5/mm in eyes with 120-μm cap thickness and 54.7 ± 8.6/mm in eyes with 140-μm cap thickness (P < 0.001). The hyperreflectivity line at the interface layer almost disappeared in all eyes with 140-μm cap thickness, and it still persisted in 43% of the fellow eyes at 3 months postoperatively. The anterior surfaces of lenticules in the 140-μm cap thickness group exhibited more smoothness than in the 120-μm cap thickness group. There was a lower level corneal wound-healing response after SMILE with a 140-μm cap thickness than with a 120-μm cap thickness, although the thickness of cap creation did not affect visual outcomes by 3 months postoperatively.

Analysis of RNA-Seq datasets reveals enrichment of tissue-specific splice variants for nuclear envelope proteins.

PubMed

Capitanchik, Charlotte; Dixon, Charles; Swanson, Selene K; Florens, Laurence; Kerr, Alastair R W; Schirmer, Eric C

2018-06-18

Nuclear envelopathies/laminopathies yield tissue-specific pathologies, yet arise from mutation of ubiquitously-expressed genes. One possible explanation of this tissue specificity is that tissue-specific partners become disrupted from larger complexes, but a little investigated alternate hypothesis is that the mutated proteins themselves have tissue-specific splice variants. Here, we analyze RNA-Seq datasets to identify muscle-specific splice variants of nuclear envelope genes that could be relevant to the study of laminopathies, particularly muscular dystrophies, that are not currently annotated in sequence databases. Notably, we found novel isoforms or tissue-specificity of isoforms for: Lap2, linked to cardiomyopathy; Nesprin 2, linked to Emery-Dreifuss muscular dystrophy and Lmo7, a regulator of the emerin gene that is linked to Emery-Dreifuss muscular dystrophy. Interestingly, the muscle-specific exon in Lmo7 is rich in serine phosphorylation motifs, suggesting an important regulatory function. Evidence for muscle-specific splice variants in non-nuclear envelope proteins linked to other muscular dystrophies was also found. Tissue-specific variants were also indicated for several nucleoporins including Nup54, Nup133, Nup153 and Nup358/RanBP2. We confirmed expression of novel Lmo7 and RanBP2 variants with RT-PCR and found that specific knockdown of the Lmo7 variant caused a reduction in myogenic index during mouse C2C12 myogenesis. Global analysis revealed an enrichment of tissue-specific splice variants for nuclear envelope proteins in general compared to the rest of the genome, suggesting that splice variants contribute to regulating its tissue-specific functions.

Reinforcement of composite laminate free edges with U-shaped caps

NASA Technical Reports Server (NTRS)

Howard, W. E.; Gossard, T., Jr.; Jones, R. M.

1986-01-01

Generalized plane strain finite element analysis is used to predict reduction of interlaminar normal stresses when a U-shaped cap is bonded to the edge of a laminate. Three-dimensional composite material failure criteria are used in a progressive laminate failure analysis to predict failure loads of laminates with different edge cap designs. In an experimental program, symmetric 11-layer graphite-epoxy laminates with a one-layer cap of Kevlar-epoxy cloth are shown to be 130 to 140 percent stronger than uncapped laminates under static tensile and tension-tension fatigue loading. In addition, the coefficient of variation of the static tensile failure load decreases from 24 to 8 percent when edge caps are added. The predicted failure load calculated with the finite element results is 10 percent lower than the actual failure load. For both capped and uncapped laminates, actual failure loads are much lower than those predicted using classical lamination theory stresses and a two-dimensional failure criterion. Possible applications of the free edge reinforcement concept are described, and future research is suggested.

Martian Polar Impact Craters: A Preliminary Assessment Using Mars Orbiter Laser Altimeter (MOLA)

NASA Technical Reports Server (NTRS)

Sakimoto, S. E. H.; Garvin, J. B.

1999-01-01

Our knowledge of the age of the layered polar deposits and their activity in the volatile cycling and climate history of Mars is based to a large extent on their apparent ages as determined from crater counts. Interpretation of the polar stratigraphy (in terms of climate change) is complicated by reported differences in the ages of the northern and southern layered deposits. The north polar residual ice deposits are thought to be relatively young, based on the reported lack of any fresh impact craters in Viking Orbiter Images. Herkenhoff et al., report no craters at all on the North polar layered deposits or ice cap, and placed an upper bound on the surface age (or, alternatively, the vertical resurfacing rate) of 100 thousand years to 10 million years, suggesting that the north polar region is an active resurfacing site. In contrast, the southern polar region was found to have at least 15 impact craters in the layered deposits and cap. Plaut et al, concluded that the surface was less than or = 120 million years old. This reported age difference factor of 100 to 1000 increases complexity in climate and volatile modeling. Recent MOLA results for the topography of the northern polar cap document a handful or more of possible craters, which could result in revised age or resurfacing estimates for the northern cap. This study is a preliminary look at putative craters in both polar caps. Additional information is contained in the original extended abstract.

Modeling large wind farms in conventionally neutral atmospheric boundary layers under varying initial conditions

NASA Astrophysics Data System (ADS)

Allaerts, Dries; Meyers, Johan

2014-05-01

Atmospheric boundary layers (ABL) are frequently capped by an inversion layer limiting the entrainment rate and boundary layer growth. Commonly used analytical models state that the entrainment rate is inversely proportional to the inversion strength. The height of the inversion turns out to be a second important parameter. Conventionally neutral atmospheric boundary layers (CNBL) are ABLs with zero surface heat flux developing against a stratified free atmosphere. In this regime the inversion-filling process is merely driven by the downward heat flux at the inversion base. As a result, CNBLs are strongly dependent on the heating history of the boundary layer and strong inversions will fail to erode during the course of the day. In case of large wind farms, the power output of the farm inside a CNBL will depend on the height and strength of the inversion above the boundary layer. On the other hand, increased turbulence levels induced by wind farms may partially undermine the rigid lid effect of the capping inversion, enhance vertical entrainment of air into the farm, and increase boundary layer growth. A suite of large eddy simulations (LES) is performed to investigate the effect of the capping inversion on the conventionally neutral atmospheric boundary layer and on the wind farm performance under varying initial conditions. For these simulations our in-house pseudo-spectral LES code SP-Wind is used. The wind turbines are modelled using a non-rotating actuator disk method. In the absence of wind farms, we find that a decrease in inversion strength corresponds to a decrease in the geostrophic angle and an increase in entrainment rate and geostrophic drag. Placing the initial inversion base at higher altitudes further reduces the effect of the capping inversion on the boundary layer. The inversion can be fully neglected once it is situated above the equilibrium height that a truly neutral boundary layer would attain under the same external conditions such as geostrophic wind speed and surface roughness. Wind farm simulations show the expected increase in boundary layer height and growth rate with respect to the case without wind farms. Raising the initial strength of the capping inversion in these simulations dampens the turbulent growth of the boundary layer above the farm, decreasing the farms energy extraction. The authors acknowledge support from the European Research Council (FP7-Ideas, grant no. 306471). Simulations were performed on the computing infrastructure of the VSC Flemish Supercomputer Center, funded by the Hercules Foundation and the Flemish Government.

Suppression of gate leakage current in in-situ grown AlN/InAlN/AlN/GaN heterostructures based on the control of internal polarization fields

NASA Astrophysics Data System (ADS)

Kotani, Junji; Yamada, Atsushi; Ishiguro, Tetsuro; Yamaguchi, Hideshi; Nakamura, Norikazu

2017-03-01

This paper investigates the gate leakage characteristics of in-situ AlN capped InAlN/AlN/GaN heterostructures grown by metal-organic vapor phase epitaxy. It was revealed that the leakage characteristics of AlN capped InAlN/AlN/GaN heterostructures are strongly dependent on the growth temperature of the AlN cap. For an AlN capped structure with an AlN growth temperature of 740 °C, the leakage current even increased although there exists a large bandgap material on InAlN/AlN/GaN heterostructures. On the other hand, a large reduction of the gate leakage current by 4-5 orders of magnitudes was achieved with a very low AlN growth temperature of 430 °C. X-ray diffraction analysis of the AlN cap grown at 740 °C indicated that the AlN layer is tensile-strained. In contrast to this result, the amorphous structure was confirmed for the AlN cap grown at 430 °C by transmission electron microscopy. Furthermore, theoretical analysis based on one-dimensional band simulation was carried out, and the large increase in two-dimensional electron gas (2DEG) observed in Hall measurements was well reproduced by taking into account the spontaneous and piezo-electric polarization in the AlN layer grown at 740 °C. For the AlN capped structure grown at 430 °C, it is believed that the reduced polarization field in the AlN cap suppressed the penetration of 2DEG into the InAlN barrier layer, resulting in a small impact on 2DEG mobility and density. We believe that an in-situ grown AlN cap with a very low growth temperature of 430 °C is a promising candidate for high-frequency/high-power GaN-based devices with low gate leakage current.

The electrical resistance of gold-capped chromium thin films

NASA Astrophysics Data System (ADS)

Ohashi, Masashi; Sawabu, Masaki; Ohashi, Kohei; Miyagawa, Masahiro; Maeta, Kae; Kubota, Takahide; Takanashi, Koki

2018-03-01

We studied the electrical resistance of polycrystalline chromium films capped by a gold layer. No anomaly was detected by resistance measurements of 10 nm thick film around room temperature, indicating that the antiferromagnetic interaction may be suppressed as decreasing the thickness of the chromium film. The sheet resistance Rs (T) curves differ from polycrystalline chromium films in previous studies because of the electrical current flows through a gold capping layer. On the other hand, the resistance drop is observed at T C = 1.15±0.05 K as that of polycrystalline chromium films in the previous report. It means that such resistance drop is not related to the chromium oxide layer on a polycrystalline chromium films. However, it is difficult to conclude that superconducting transition occurs because of the large residual resistance below the temperature where the resistance drop is observed.

Investigation of Martian H2O and CO2 via gamma-ray spectroscopy

NASA Technical Reports Server (NTRS)

Squyres, Steven W.; Evans, Larry G.

1987-01-01

The evolution and present state of water and carbon dioxide on Mars are discussed. Researchers wished to determine how effectively questions regarding the distribution of water and carbon dioxide on Mars may be addressed with orbital gamma ray spectrometer data. Several simple, multi-layer models of the Martian surface were formulated to address problems such as the ice/dust ratio of layered deposits; the distribution, depth and concentration of ground ice; the thickness of north polar perennial ice; the thickness of the carbon dioxide layer over the south polar cap; the thickness of the seasonal carbon dioxide frost cap; and the water content of the seasonal frost cap. The results indicate that the Mars Observer gamma ray spectrometer will be a powerful tool for investigating the distribution and stratigraphy of volatiles on Mars.

Achieving high field-effect mobility in amorphous indium-gallium-zinc oxide by capping a strong reduction layer.

PubMed

Zan, Hsiao-Wen; Yeh, Chun-Cheng; Meng, Hsin-Fei; Tsai, Chuang-Chuang; Chen, Liang-Hao

2012-07-10

An effective approach to reduce defects and increase electron mobility in a-IGZO thin-film transistors (a-IGZO TFTs) is introduced. A strong reduction layer, calcium, is capped onto the back interface of a-IGZO TFT. After calcium capping, the effective electron mobility of a-IGZO TFT increases from 12 cm(2) V(-1) s(-1) to 160 cm(2) V(-1) s(-1). This high mobility is a new record, which implies that the proposed defect reduction effect is key to improve electron transport in oxide semiconductor materials. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Combined Field and Laboratory Study on Activated Carbon-Based Thin Layer Capping in a PCB-Contaminated Boreal Lake.

PubMed

Abel, Sebastian; Akkanen, Jarkko

2018-04-17

The in situ remediation of aquatic sediments with activated carbon (AC)-based thin layer capping is a promising alternative to traditional methods, such as sediment dredging. Applying a strong sorbent like AC directly to the sediment can greatly reduce the bioavailability of organic pollutants. To evaluate the method under realistic field conditions, a 300 m 2 plot in the PCB-contaminated Lake Kernaalanjärvi, Finland, was amended with an AC cap (1.6 kgAC/m 2 ). The study lake showed highly dynamic sediment movements over the monitoring period of 14 months. This led to poor retention and rapid burial of the AC cap under a layer of contaminated sediment from adjacent sites. As a result, the measured impact of the AC amendment was low: Both the benthic community structure and PCB bioaccumulation were similar on the plot and in surrounding reference sites. Corresponding follow-up laboratory studies using Lumbriculus variegatus and Chironomus riparius showed that long-term remediation success is possible, even when an AC cap is covered with contaminated sediment. To retain a measurable effectiveness (reduction in contaminant bioaccumulation), a sufficient intensity and depth of bioturbation is required. On the other hand, the magnitude of the adverse effect induced by AC correlated positively with the measured remediation success.

Electromagnetically induced reflectance and Fano resonance in one dimensional superconducting photonic crystal

NASA Astrophysics Data System (ADS)

Athe, Pratik; Srivastava, Sanjay; Thapa, Khem B.

2018-04-01

In the present work, we demonstrate the generation of optical Fano resonance and electromagnetically induced reflectance (EIR) in one-dimensional superconducting photonic crystal (1D SPC) by numerical simulation using transfer matrix method as analysis tool. We investigated the optical response of 1D SPC structure consisting of alternate layer of two different superconductors and observed that the optical spectra of this structure exhibit two narrow reflectance peaks with zero reflectivity of sidebands. Further, we added a dielectric cap layer to this 1D SPC structure and found that addition of dielectric cap layer transforms the line shape of sidebands around the narrow reflectance peaks which leads to the formation of Fano resonance and EIR line shape in reflectance spectra. We also studied the effects of the number of periods, refractive index and thickness of dielectric cap layer on the lineshape of EIR and Fano resonances. It was observed that the amplitude of peak reflectance of EIR achieves 100% reflectance by increasing the number of periods.

High performance EUV multilayer structures insensitive to capping layer optical parameters.

PubMed

Pelizzo, Maria Guglielmina; Suman, Michele; Monaco, Gianni; Nicolosi, Piergiorgio; Windt, David L

2008-09-15

We have designed and tested a-periodic multilayer structures containing protective capping layers in order to obtain improved stability with respect to any possible changes of the capping layer optical properties (due to oxidation and contamination, for example)-while simultaneously maximizing the EUV reflection efficiency for specific applications, and in particular for EUV lithography. Such coatings may be particularly useful in EUV lithographic apparatus, because they provide both high integrated photon flux and higher stability to the harsh operating environment, which can affect seriously the performance of the multilayer-coated projector system optics. In this work, an evolutive algorithm has been developed in order to design these a-periodic structures, which have been proven to have also the property of stable performance with respect to random layer thickness errors that might occur during coating deposition. Prototypes have been fabricated, and tested with EUV and X-ray reflectometry, and secondary electron spectroscopy. The experimental results clearly show improved performance of our new a-periodic coatings design compared with standard periodic multilayer structures.

High Performance 0.1 μm GaAs Pseudomorphic High Electron Mobility Transistors with Si Pulse-Doped Cap Layer for 77 GHz Car Radar Applications

NASA Astrophysics Data System (ADS)

Kim, Sungwon; Noh, Hunhee; Jang, Kyoungchul; Lee, JaeHak; Seo, Kwangseok

2005-04-01

In this study, 0.1 μm double-recessed T-gate GaAs pseudomorphic high electron mobility transistors (PHEMT’s), in which an InGaAs layer and a Si pulse-doped layer in the cap structure are inserted, have been successfully fabricated. This cap structure improves ohmic contact. The ohmic contact resistance is as small as 0.07 Ωmm, consequently the source resistance is reduced by about 20% compared to that of a conventional cap structure. This device shows good DC and microwave performance such as an extrinsic transconductance of 620 mS/mm, a maximum saturated drain current of 780 mA/mm, a cut-off frequency fT of 140 GHz and a maximum oscillation frequency of 260 GHz. The reverse breakdown is 5.7 V at a gate current density of 1 mA/mm. The maximum available gain is about 7 dB at 77 GHz. It is well suited for car radar monolithic microwave integrated circuits (MMICs).

The Mars water cycle at other epochs: History of the polar caps and layered terrain

NASA Technical Reports Server (NTRS)

Jakosky, Bruce M.; Henderson, Bradley G.; Mellon, Michael T.

1992-01-01

The atmospheric water cycle at the present epoch involves summertime sublimation of water from the north polar cap, transport of water through the atmosphere, and condensation on one or both winter CO2 caps. Exchange with the regolith is important seasonally, but the water content of the atmosphere appears to be controlled by the polar caps. The net annual transport through the atmosphere, integrated over long timescales, must be the driving force behind the long-term evolution of the polar caps; clearly, this feeds back into the evolution of the layered terrain. We have investigated the behavior of the seasonal water cycle and the net integrated behavior at the pole for the last 10 exp 7 years. Our model of the water cycle includes the solar input, CO2 condensation and sublimation, and summertime water sublimation through the seasonal cycles, and incorporates the long-term variations in the orbital elements describing the Martian orbit.

The effect of a nonmagnetic cap layer on the spin-polarized tunneling and magnetoresistance in double-barrier planar junctions

NASA Astrophysics Data System (ADS)

Xie, Zheng-Wei; Li, Bo-Zang; Li, Yu-Xian

2003-10-01

Within the framework of the free-electron model, the tunneling magnetoresistance (TMR) and tunneling conductance (TC) in double magnetic tunnel junctions (DMTJ) with nonmagnetic cap layer, i.e. the NM/FM/I/NM/(FM)/I/FM/NM junction is investigated. FM, NM and I represent the ferromagnetic metal, nonmagnetic metal and insulator, respectively, NM(FM) indicates that the middle layer can be NM or FM. Our results show that, due to the spin-dependent interfacial potential barriers, the influences of the thickness of the FM layer on TC and TMR in DMTJ are large, and when the thicknesses of these two FM layers are suitable a large TMR can be obtained. (

Cold-Cap Temperature Profile Comparison between the Laboratory and Mathematical Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixon, Derek R.; Schweiger, Michael J.; Riley, Brian J.

2015-06-01

The rate of waste vitrification in an electric melter is connected to the feed-to-glass conversion process, which occurs in the cold cap, a layer of reacting feed on top of molten glass. The cold cap consists of two layers: a low temperature (~100°C – ~800°C) region of unconnected feed and a high temperature (~800°C – ~1100°C) region of foam with gas bubbles and cavities mixed in the connected glass melt. A recently developed mathematical model describes the effect of the cold cap on glass production. For verification of the mathematical model, a laboratory-scale melter was used to produce a coldmore » cap that could be cross-sectioned and polished in order to determine the temperature profile related to position in the cold cap. The cold cap from the laboratory-scale melter exhibited an accumulation of feed ~400°C due to radiant heat from the molten glass creating dry feed conditions in the melter, which was not the case in the mathematical model where wet feed conditions were calculated. Through the temperature range from ~500°C – ~1100°C, there was good agreement between the model and the laboratory cold cap. Differences were observed between the two temperature profiles due to the temperature of the glass melts and the lack of secondary foam, large cavities, and shrinkage of the primary foam bubbles upon the cooling of the laboratory-scale cold cap.« less

Variability of Mars' North Polar Water Ice Cap: I. Analysis of Mariner 9 and Viking Orbiter Imaging Data

USGS Publications Warehouse

Bass, Deborah S.; Herkenhoff, Kenneth; Paige, David A.

2000-01-01

Previous studies interpreted differences in ice coverage between Mariner 9 and Viking Orbiter observations of Mars' north residual polar cap as evidence of interannual variability of ice deposition on the cap. However, these investigators did not consider the possibility that there could be significant changes in the ice coverage within the northern residual cap over the course of the summer season. Our more comprehensive analysis of Mariner 9 and Viking Orbiter imaging data shows that the appearance of the residual cap does not show large-scale variance on an interannual basis. Rather we find evidence that regions that were dark at the beginning of summer look bright by the end of summer and that this seasonal variation of the cap repeats from year to year. Our results suggest that this brightening was due to the deposition of newly formed water ice on the surface. We find that newly formed ice deposits in the summer season have the same red-to-violet band image ratios as permanently bright deposits within the residual cap. We believe the newly formed ice accumulates in a continuous layer. To constrain the minimum amount of deposited ice, we used observed albedo data in conjunction with calculations using Mie theory for single scattering and a delta-Eddington approximation of radiative transfer for multiple scattering. The brightening could have been produced by a minimum of (1) a ~35-μm-thick layer of 50-μm-sized ice particles with 10% dust or (2) a ~14-μm-thick layer of 10-μm-sized ice particles with 50% dust.

Immune-related zinc finger gene ZFAT is an essential transcriptional regulator for hematopoietic differentiation in blood islands

PubMed Central

Tsunoda, Toshiyuki; Takashima, Yasuo; Tanaka, Yoko; Fujimoto, Takahiro; Doi, Keiko; Hirose, Yumiko; Koyanagi, Midori; Yoshida, Yasuhiro; Okamura, Tadashi; Kuroki, Masahide; Sasazuki, Takehiko; Shirasawa, Senji

2010-01-01

TAL1 plays pivotal roles in vascular and hematopoietic developments through the complex with LMO2 and GATA1. Hemangioblasts, which have a differentiation potential for both endothelial and hematopoietic lineages, arise in the primitive streak and migrate into the yolk sac to form blood islands, where primitive hematopoiesis occurs. ZFAT (a zinc-finger gene in autoimmune thyroid disease susceptibility region / an immune-related transcriptional regulator containing 18 C2H2-type zinc-finger domains and one AT-hook) was originally identified as an immune-related transcriptional regulator containing 18 C2H2-type zinc-finger domains and one AT-hook, and is highly conserved among species. ZFAT is thought to be a critical transcription factor involved in immune-regulation and apoptosis; however, developmental roles for ZFAT remain unknown. Here we show that Zfat-deficient (Zfat−/−) mice are embryonic-lethal, with impaired differentiation of hematopoietic progenitor cells in blood islands, where ZFAT is exactly expressed. Expression levels of Tal1, Lmo2, and Gata1 in Zfat−/− yolk sacs are much reduced compared with those of wild-type mice, and ChIP-PCR analysis revealed that ZFAT binds promoter regions for these genes in vivo. Furthermore, profound reduction in TAL1, LMO2, and GATA1 protein expressions are observed in Zfat−/− blood islands. Taken together, these results suggest that ZFAT is indispensable for mouse embryonic development and functions as a critical transcription factor for primitive hematopoiesis through direct-regulation of Tal1, Lmo2, and Gata1. Elucidation of ZFAT functions in hematopoiesis might lead to a better understanding of transcriptional networks in differentiation and cellular programs of hematopoietic lineage and provide useful information for applied medicine in stem cell therapy. PMID:20660741

An Observational and Analytical Study of Marginal Ice Zone Atmospheric Jets

DTIC Science & Technology

2016-12-01

layer or in the capping temperature inversion just above. The three strongest jets had maximum wind speeds at elevations near 350 m to 400 m...geostrophic wind due to horizontal temperature changes in the atmospheric boundary layer and capping inversion . The jets were detected using...temperature inversion just above. The three strongest jets had maximum wind speeds at elevations near 350 m to 400 m elevation; one of these jets had a

Localized Control of Curie Temperature in Perovskite Oxide Film by Capping-Layer-Induced Octahedral Distortion

DOE PAGES

Thomas, S.; Kuiper, B.; Hu, J.; ...

2017-10-27

With reduced dimensionality, it is often easier to modify the properties of ultrathin films than their bulk counterparts. Strain engineering, usually achieved by choosing appropriate substrates, has been proven effective in controlling the properties of perovskite oxide films. An emerging alternative route for developing new multifunctional perovskite is by modification of the oxygen octahedral structure. Here we report the control of structural oxygen octahedral rotation in ultrathin perovskite SrRuO 3 films by the deposition of a SrTiO 3 capping layer, which can be lithographically patterned to achieve local control. Here, using a scanning Sagnac magnetic microscope, we show an increasemore » in the Curie temperature of SrRuO 3 due to the suppression octahedral rotations revealed by the synchrotron x-ray diffraction. Lastly, this capping-layer-based technique may open new possibilities for developing functional oxide materials.« less

Localized Control of Curie Temperature in Perovskite Oxide Film by Capping-Layer-Induced Octahedral Distortion.

PubMed

Thomas, S; Kuiper, B; Hu, J; Smit, J; Liao, Z; Zhong, Z; Rijnders, G; Vailionis, A; Wu, R; Koster, G; Xia, J

2017-10-27

With reduced dimensionality, it is often easier to modify the properties of ultrathin films than their bulk counterparts. Strain engineering, usually achieved by choosing appropriate substrates, has been proven effective in controlling the properties of perovskite oxide films. An emerging alternative route for developing new multifunctional perovskite is by modification of the oxygen octahedral structure. Here we report the control of structural oxygen octahedral rotation in ultrathin perovskite SrRuO_{3} films by the deposition of a SrTiO_{3} capping layer, which can be lithographically patterned to achieve local control. Using a scanning Sagnac magnetic microscope, we show an increase in the Curie temperature of SrRuO_{3} due to the suppression octahedral rotations revealed by the synchrotron x-ray diffraction. This capping-layer-based technique may open new possibilities for developing functional oxide materials.

Textures in south polar ice cap #1

NASA Technical Reports Server (NTRS)

1998-01-01

Textures of the south polar permanent residual ice cap and polar layered terrains. This 30 x 29 km area image (frame 7709) is centered near 87 degrees south, 77 degrees west.

Figure caption from Science Magazine

Textures in south polar ice cap #2

NASA Technical Reports Server (NTRS)

1998-01-01

Textures of the south polar permanent residual ice cap and polar layered terrains. This 15 x 14 km area image (frame 7306) is centered near 87 degrees south, 341 degrees west.

Figure caption from Science Magazine

Dry etching, surface passivation and capping processes for antimonide based photodetectors

NASA Astrophysics Data System (ADS)

Dutta, Partha; Langer, Jeffery; Bhagwat, Vinay; Juneja, Jasbir

2005-05-01

III-V antimonide based devices suffer from leakage currents. Surface passivation and subsequent capping of the surfaces are absolutely essential for any practical applicability of antimonide based devices. The quest for a suitable surface passivation technology is still on. In this paper, we will present some of the promising recent developments in this area based on dry etching of GaSb based homojunction photodiodes structures followed by various passivation and capping schemes. We have developed a damage-free, universal dry etching recipe based on unique ratios of Cl2/BCl3/CH4/Ar/H2 in ECR plasma. This novel dry plasma process etches all III-V compounds at different rates with minimal damage to the side walls. In GaSb based photodiodes, an order of magnitude lower leakage current, improved ideality factor and higher responsivity has been demonstrated using this recipe compared to widely used Cl2/Ar and wet chemical etch recipes. The dynamic zero bias resistance-area product of the Cl2/BCl3/CH4/Ar/H2 etched diodes (830 Ω cm2) is higher than the Cl2/Ar (300 Ω cm2) and wet etched (330 Ω cm2) diodes. Ammonium sulfide has been known to passivate surfaces of III-V compounds. In GaSb photodiodes, the leakage current density reduces by a factor of 3 upon sulfur passivation using ammonium sulfide. However, device performance degrades over a period of time in the absence of any capping or protective layer. Silicon Nitride has been used as a cap layer by various researchers. We have found that by using silicon nitride caps, the devices exhibit higher leakage than unpassivated devices probably due to plasma damage during SiNx deposition. We have experimented with various polymers for capping material. It has been observed that ammonium sulfide passivation when combined with parylene capping layer (150 Å), devices retain their improved performance for over 4 months.

The Influence of Impurities and Metallic Capping Layers on the Microstructure of Copper Interconnects

NASA Astrophysics Data System (ADS)

Rizzolo, Michael

As copper interconnects have scaled to ever smaller dimensions on semiconductor devices, the microstructure has become increasingly detrimental for performance and reliability. Small grains persist in interconnects despite annealing at high temperatures, leading to higher line resistance and more frequent electromigration-induced failures. Conventionally, it was believed that impurities from the electrodeposition pinned grain growth, but limitations in analytical techniques meant the effect was inferred rather than observed. Recent advances in analytical techniques, however, have enabled this work to quantify impurity content, location, and diffusion in relation to microstructural changes in electroplated copper. Surface segregation of impurities during the initial burst of grain growth was investigated. After no surface segregation was observed, a microfluidic plating cell was constructed to plate multilayer films with regions of intentionally high and low impurity concentrations to determine if grain growth could be pinned by the presence of impurities; it was not. An alternate mechanism for grain boundary pinning based on the texture of the seed layer is proposed, supported by time-resolved transmission electron microscopy and transmission electron backscatter diffraction data. The suggested model posits that the seed in narrow features has no preferred orientation, which results in rapid nucleation of subsurface grains in trench regions prior to recrystallization from the overburden down. These rapidly growing grains are able to block off several trenches from the larger overburden grains, inhibiting grain growth in narrow features. With this knowledge in hand, metallic capping layers were employed to address the problematic microstructure in 70nm lines. The capping layers (chromium, nickel, zinc, and tin) were plated on the copper overburden prior to annealing to manipulate the stress gradient and microstructural development during annealing. It appeared that regardless of as-plated stress, nickel capping altered the recrystallized texture of the copper over patterned features. The nickel capping also caused a 2x increase in the number of advantageous 'bamboo' grains that span the entire trench, which effectively block electromigration pathways. These data provides a more fundamental understanding of manipulating the microstructure in copper interconnects using pre-anneal capping layers, and demonstrates a strategy to improve the microstructure beyond the capabilities of simple annealing.

Optical Tamm states in one-dimensional superconducting photonic crystal

DOE Office of Scientific and Technical Information (OSTI.GOV)

El Abouti, O.; El Boudouti, E. H.; IEMN, UMR-CNRS 8520, UFR de Physique, Université de Lille 1, 59655 Villeneuve d'Ascq

2016-08-15

In this study, we investigate localized and resonant optical waves associated with a semi-infinite superlattice made out of superconductor-dielectric bilayers and terminated with a cap layer. Both transverse electric and transverse magnetic waves are considered. These surface modes are analogous to the so-called Tamm states associated with electronic states found at the surface of materials. The surface guided modes induced by the cap layer strongly depend on whether the superlattice ends with a superconductor or a dielectric layer, the thickness of the surface layer, the temperature of the superconductor layer as well as on the polarization of the waves. Differentmore » kinds of surface modes are found and their properties examined. These structures can be used to realize the highly sensitive photonic crystal sensors.« less

Design of an optimised readout architecture for phase-change probe memory using Ge2Sb2Te5 media

NASA Astrophysics Data System (ADS)

Wang, Lei; Wright, C. David; Aziz, Mustafa M.; Yang, Ci-Hui; Yang, Guo-Wei

2014-02-01

Phase-change probe memory has recently received considerable attention on its writing performance, while its readout performance is rarely evaluated. Therefore, a three-dimensional readout model has been developed for the first time to calculate the reading contrast by varying the electrical conductivities and the thickness of the capping and under layers as well as the thickness of the Ge2Sb2Te5 layer. It is found that a phase-change probe architecture, consisting of a 10 nm Ge2Sb2Te5 layer sandwiched by a 2 nm, 50 Ω-1 m-1 capping layer and a 40 nm, 5 × 106 Ω-1 m-1 under layer, has the capability of providing the optimal readout performance.

Evolution of the Moon's Mantle and Crust as Reflected in Trace-Element Microbeam Studies of Lunar Magmatism

NASA Astrophysics Data System (ADS)

Shearer, C. K.; Floss, C.

Ion microprobe trace-element studies of lunar cumulates [ferroan anorthosites (FAN), highlands Mg suite (HMS), and highlands alkali suite (HAS)] and volcanic glasses have provided an additional perspective in reconstructing lunar magmatism and early differentiation. Calculated melt compositions for the FANs indicate that a simple lunar magma ocean (LMO) model does not account for differences between FANs with highly magnesian mafic minerals and “typical” ferroan anorthosites. The HMS and HAS appear to have crystallized from magmas that had incompatible trace-element concentrations equal to or greater than KREEP. Partial melting of distinct, hybridized sources is consistent with these calculated melt compositions. However, the high-Mg silicates with relatively low Ni content that are observed in the HMS are suggestive of other possible processes (reduction, metal removal). The compositions of the picritic glasses indicate that they were produced by melting of hybrid cumulate sources produced by mixing of early and late LMO cumulates. The wide compositional range of near-primitive mare basalts indicates small degrees of localized melting preserved the signature of distinct mantle reservoirs. The relationship between ilmenite anomalies and 182W in the mare basalts suggests that the LMO crystallized over a short period of time.

Sodium chloride-induced filamentation and alternative gene expression of fts, murZ, and gnd in Listeria monocytogenes 08-5923 on vacuum-packaged ham.

PubMed

Liu, Xiaoji; Miller, Petr; Basu, Urmila; McMullen, Lynn M

2014-11-01

The aim of this study was to examine the filament formation and differential gene expression of Listeria monocytogenes 08-5923 grown on refrigerated vacuum-packaged ham products with various NaCl concentrations. Filament formation of L. monocytogenes was observed on ham products with 1.35% and 2.35% NaCl, which was monitored using flow cytometry by measuring forward light scatter. Quantitative real-time PCR was used to study the differential expression of genes in filamented cells of L. monocytogenes grown on hams following 2 or 3 months of storage at 4 °C. The genes involved in cell division (ftsX/lmo2506), cell wall synthesis (murZ/lmo2552), and NADPH production (gnd/lmo1376) were significantly downregulated in filamented cells of L. monocytogenes grown on ham with 2.35% NaCl stored at 4 °C. To our knowledge, this study reports the first evidence of filament formation of Listeria grown on meat products, which could impact the food safety risk and tolerance levels of L. monocytogenes set by regulatory agencies. © 2014 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

Basal sublimation and venting of the north seasonal cap of Mars

NASA Astrophysics Data System (ADS)

Piqueux, S.; Christensen, P. R.

2007-12-01

Spots, fans and dark polygonal patterns form during the spring on the southern seasonal cap of Mars as a consequence of 1) the basal sublimation of the translucent and impermeable slab of carbon dioxide and 2) the venting of the CO2 gas loaded with dust and sand size material scoured from the surface of the polar layered deposits. The dark polygons on the cap have a similar formation process as the spots but the dust and sand erupt from elongated vents rather than point sources. In the summer, spiders and etched polygons remain on the southern polar layered deposits. The spiders are shaped by the scouring action of confined CO2 gas flowing between the cap and the basement and converging toward point sources, whereas the etched polygons result form the forced migration of the CO2 gas over longer distances. Comparable observations during the spring near the north pole on the seasonal cap indicate that similar processes occur in both polar regions and that the venting model developed for the south seasonal cap also operates near the north pole. However, spider and etched polygonal features are extremely uncommon on the north substrate, indicating that the conditions for their formation (e.g. mechanical strength of the slab and the substrate, transparency of the seasonal cap) are not met. The continual erosion and re-sedimentation occurring at the surface of the polar layered deposits by the seasonal degassing is a major geomorphological agent shaping the polar regions. The polar layered deposits have been proposed to contain the stratigraphic record of climatic changes and catastrophic events of very high interest for future missions. Our observations suggest that both polar regions deposits may have been locally disrupted by the seasonal sub-ice gas flow and that the stratigraphic record may have been partially lost. The Phoenix landing site might have been affected in the past and the stratigraphic information associated with the original deposition of the polar material partially disrupted due to this surface reworking.

Ballistocardiogram Artifact Removal with a Reference Layer and Standard EEG Cap

PubMed Central

Luo, Qingfei; Huang, Xiaoshan; Glover, Gary H.

2014-01-01

Background In simultaneous EEG-fMRI, the EEG recordings are severely contaminated by ballistocardiogram (BCG) artifacts, which are caused by cardiac pulsations. To reconstruct and remove the BCG artifacts, one promising method is to measure the artifacts in the absence of EEG signal by placing a group of electrodes (BCG electrodes) on a conductive layer (reference layer) insulated from the scalp. However, current BCG reference layer (BRL) methods either use a customized EEG cap composed of electrode pairs, or need to construct the custom reference layer through additional model-building experiments for each EEG-fMRI experiment. These requirements have limited the versatility and efficiency of BRL. The aim of this study is to propose a more practical and efficient BRL method and compare its performance with the most popular BCG removal method, the optimal basis sets (OBS) algorithm. New Method By designing the reference layer as a permanent and reusable cap, the new BRL method is able to be used with a standard EEG cap, and no extra experiments and preparations are needed to use the BRL in an EEG-fMRI experiment. Results The BRL method effectively removed the BCG artifacts from both oscillatory and evoked potential scalp recordings and recovered the EEG signal. Comparison with Existing Method Compared to the OBS, this new BRL method improved the contrast-to-noise ratios of the alpha-wave, visual, and auditory evoked potential signals by 101%, 76%, and 75% respectively, employing 160 BCG electrodes. Using only 20 BCG electrodes, the BRL improved the EEG signal by 74%/26%/41% respectively. Conclusion The proposed method can substantially improve the EEG signal quality compared with traditional methods. PMID:24960423

What Lies Below a Martian Ice Cap

NASA Technical Reports Server (NTRS)

2008-01-01

[figure removed for brevity, see original site] Click on image for larger annotated version

This image (top) taken by the Shallow Radar instrument on NASA's Mars Reconnaissance Orbiter reveals the layers of ice, sand and dust that make up the north polar ice cap on Mars. It is the most detailed look to date at the insides of this ice cap. The colored map below the radar picture shows the topography of the corresponding Martian terrain (red and white represent higher ground, and green and yellow lower).

The radar image reveals four never-before-seen thick layers of ice and dust separated by layers of nearly pure ice. According to scientists, these thick ice-free layers represent approximately one-million-year-long cycles of climate change on Mars caused by variations in the planet's tilted axis and its eccentric orbit around the sun. Adding up the entire stack of ice gives an estimated age for the north polar ice cap of about 4 million years a finding that agrees with previous theoretical estimates. The ice cap is about 2 kilometers (1.2 miles) thick.

The radar picture also shows that the boundary between the ice layers and the surface of Mars underneath is relatively flat (bottom white line on the right). This implies that the surface of Mars is not sagging, or bending, under the weight of the ice cap and this, in turn, suggests that the planet's lithosphere, a combination of the crust and the strong parts of the upper mantle, is thicker than previously thought.

A thicker lithosphere on Mars means that temperatures increase more gradually with depth toward the interior. Temperatures warm enough for water to be liquid are therefore deeper than previously thought. Likewise, if liquid water does exist in aquifers below the surface of Mars, and if there are any organisms living in that water, they would have to be located deeper in the planet.

The topography data are from Mars Orbiter Laser Altimeter, which was flown on NASA's Mars Global Surveyor mission.

NPLD stands for the north polar layered deposits.

BU stands for basal unit, an ice-sand deposit that lies beneath parts of the north polar layered deposits.

The Shallow Radar instrument was provided by the Italian Space Agency. Its operations are led by the University of Rome and its data are analyzed by a joint U.S.-Italian science team. JPL, a division of the California Institute of Technology, Pasadena, manages the Mars Reconnaissance Orbiter for the NASA Science Mission Directorate, Washington.

RNA Cap Methyltransferase Activity Assay

PubMed Central

Trotman, Jackson B.; Schoenberg, Daniel R.

2018-01-01

Methyltransferases that methylate the guanine-N7 position of the mRNA 5′ cap structure are ubiquitous among eukaryotes and commonly encoded by viruses. Here we provide a detailed protocol for the biochemical analysis of RNA cap methyltransferase activity of biological samples. This assay involves incubation of cap-methyltransferase-containing samples with a [32P]G-capped RNA substrate and S-adenosylmethionine (SAM) to produce RNAs with N7-methylated caps. The extent of cap methylation is then determined by P1 nuclease digestion, thin-layer chromatography (TLC), and phosphorimaging. The protocol described here includes additional steps for generating the [32P]G-capped RNA substrate and for preparing nuclear and cytoplasmic extracts from mammalian cells. This assay is also applicable to analyzing the cap methyltransferase activity of other biological samples, including recombinant protein preparations and fractions from analytical separations and immunoprecipitation/pulldown experiments. PMID:29644259

Magneto-optical properties of CoFeB ultrathin films: Effect of Ta buffer and capping layer

NASA Astrophysics Data System (ADS)

Husain, Sajid; Gupta, Nanhe Kumar; Barwal, Vineet; Chaudhary, Sujeet

2018-05-01

The effect of adding Ta as a capping and buffer layer on ultrathin CFB(Co60Fe20B20) thin films has been investigated by magneto-optical Kerr effect. A large difference in the coercivity and saturation field is observed between the single layer CFB(2nm) and Ta(5nm)/CFB(2nm)/Ta(2nm) trilayer structure. In particular, the in-plane anisotropy energy is found to be 90kJ/m3 on CFB(2nm) and 2.22kJ/m3 for Ta(5nm)/CFB(2nm)/Ta(2nm) thin films. Anisotropy energy further reduced to 0.93kJ/m3 on increasing the CFB thinness in trilayer structure i.e., Ta(5nm)/CFB(4nm)/Ta(2nm). Using VSM measurement, the saturation magnetization is found to be 1230±50 kA/m. Low coercivity and anisotropy energy in capped and buffer layer thin films envisage the potential of employing CFB for low field switching applications of the spintronic devices.

Alginate edible films containing microencapsulated lemongrass oil or citral: effect of encapsulating agent and storage time on physical and antimicrobial properties.

PubMed

Alarcón-Moyano, Jessica K; Bustos, Rubén O; Herrera, María Lidia; Matiacevich, Silvia B

2017-08-01

Active edible films have been proposed as an alternative to extend shelf life of fresh foods. Most essential oils have antimicrobial properties; however, storage conditions could reduce their activity. To avoid this effect the essential oil (EO) can be microencapsulated prior to film casting. The aim of this study was to determine the effects of the type of encapsulating agent (EA), type of EO and storage time on physical properties and antimicrobial activity of alginate-based films against Escherichia coli ATCC 25922. Trehalose (TH), Capsul ® (CAP) and Tween 20 (Tw20) were used as EA. Lemongrass essential oil (LMO) and citral were used as active agents. The results showed that the type of EA affected the stability of the film forming-emulsions as well as the changes in opacity and colour of the films during storage but not the antimicrobial activity of them. Both microencapsulated EOs showed a prolonged release from the alginate films during the 28 days of storage. Trehalose was selected to encapsulate both active compounds because the films made with this microencapsulated EA showed the greatest physical stability and the lowest color variation among all the films studied.

Morphological and functional changes in RAW264 macrophage-like cells in response to a hydrated layer of carbonate-substituted hydroxyapatite.

PubMed

Igeta, Kazuki; Kuwamura, Yuta; Horiuchi, Naohiro; Nozaki, Kosuke; Shiraishi, Daichi; Aizawa, Mamoru; Hashimoto, Kazuaki; Yamashita, Kimihiro; Nagai, Akiko

2017-04-01

Synthetic hydroxyapatite (HAp) is used clinically as a material for bone prostheses owing to its good bone-bonding ability; however, it does not contribute to bone remodeling. Carbonate-substituted hydroxyapatite (CAp) has greater bioresorption capacity than HAp while having similar bone-bonding potential, and is therefore considered as a next promising material for bone prostheses. However, the effects of the CAp instability on inflammatory and immune responses are unknown in detail. Here, we show that the surface layer of CAp is more hydrated than that of HAp and induces changes in the shape and function of macrophage-like cells. HAp and CAp were synthesized by wet method and molded into disks. The carbonate content of CAp disks was 6.2% as determined by Fourier transform (FT) infrared spectral analysis. Diffuse reflectance infrared FT analysis confirmed that physisorbed water and surface hydroxyl groups (OH - ) were increased whereas structural OH - was decreased on the CAp as compared to the HAp surface. The degree of hydroxylation in CAp was comparable to that in bone-apatite structures, and the CAp surface exhibited greater hydrophilicity and solubility than HAp. We investigated immune responses to these materials by culturing RAW264 cells (macrophage precursors) on their surfaces. Cell spreading on the CAp disk was suppressed and the secretion level of inflammatory cytokines was reduced as compared to cells grown on HAp. These results indicate that the greater surface hydration of CAp surface can attenuate adverse inflammatory responses to implanted bone prostheses composed of this material. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 1063-1070, 2017. © 2017 Wiley Periodicals, Inc.

Blue-Light Inhibition of Listeria monocytogenes Growth Is Mediated by Reactive Oxygen Species and Is Influenced by σB and the Blue-Light Sensor Lmo0799.

PubMed

O'Donoghue, Beth; NicAogáin, Kerrie; Bennett, Claire; Conneely, Alan; Tiensuu, Teresa; Johansson, Jörgen; O'Byrne, Conor

2016-07-01

Listeria monocytogenes senses blue light via the flavin mononucleotide-containing sensory protein Lmo0799, leading to activation of the general stress response sigma factor SigB (σ(B)). In this study, we investigated the physiological response of this foodborne pathogen to blue light. We show that blue light (460 to 470 nm) doses of 1.5 to 2 mW cm(-2) cause inhibition of growth on agar-based and liquid culture media. The inhibitory effects are dependent on cell density, with reduced effects evident when high cell numbers are present. The addition of 20 mM dimethylthiourea, a scavenger of reactive oxygen species, or catalase to the medium reverses the inhibitory effects of blue light, suggesting that growth inhibition is mediated by the formation of reactive oxygen species. A mutant strain lacking σ(B) (ΔsigB) was found to be less inhibited by blue light than the wild type, likely indicating the energetic cost of deploying the general stress response. When a lethal dose of light (8 mW cm(-2)) was applied to cells, the ΔsigB mutant displayed a marked increase in sensitivity to light compared to the wild type. To investigate the role of the blue-light sensor Lmo0799, mutants were constructed that either had a deletion of the gene (Δlmo0799) or alteration in a conserved cysteine residue at position 56, which is predicted to play a pivotal role in the photocycle of the protein (lmo0799 C56A). Both mutants displayed phenotypes similar to the ΔsigB mutant in the presence of blue light, providing genetic evidence that residue 56 is critical for light sensing in L. monocytogenes Taken together, these results demonstrate that L. monocytogenes is inhibited by blue light in a manner that depends on reactive oxygen species, and they demonstrate clear light-dependent phenotypes associated with σ(B) and the blue-light sensor Lmo0799. Listeria monocytogenes is a bacterial foodborne pathogen that can cause life-threatening infections in humans. It is known to be able to sense and respond to visible light. In this study, we examine the effects of blue light on the growth and survival of this pathogen. We show that growth can be inhibited at comparatively low doses of blue light, and that at higher doses, L. monocytogenes cells are killed. We present evidence suggesting that blue light inhibits this organism by causing the production of reactive oxygen species, such as hydrogen peroxide. We help clarify the mechanism of light sensing by constructing a "blind" version of the blue-light sensor protein. Finally, we show that activation of the general stress response by light has a negative effect on growth, probably because cellular resources are diverted into protective mechanisms rather than growth. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Blue-Light Inhibition of Listeria monocytogenes Growth Is Mediated by Reactive Oxygen Species and Is Influenced by σB and the Blue-Light Sensor Lmo0799

PubMed Central

O'Donoghue, Beth; NicAogáin, Kerrie; Bennett, Claire; Conneely, Alan; Tiensuu, Teresa; Johansson, Jörgen

2016-01-01

ABSTRACT Listeria monocytogenes senses blue light via the flavin mononucleotide-containing sensory protein Lmo0799, leading to activation of the general stress response sigma factor SigB (σB). In this study, we investigated the physiological response of this foodborne pathogen to blue light. We show that blue light (460 to 470 nm) doses of 1.5 to 2 mW cm−2 cause inhibition of growth on agar-based and liquid culture media. The inhibitory effects are dependent on cell density, with reduced effects evident when high cell numbers are present. The addition of 20 mM dimethylthiourea, a scavenger of reactive oxygen species, or catalase to the medium reverses the inhibitory effects of blue light, suggesting that growth inhibition is mediated by the formation of reactive oxygen species. A mutant strain lacking σB (ΔsigB) was found to be less inhibited by blue light than the wild type, likely indicating the energetic cost of deploying the general stress response. When a lethal dose of light (8 mW cm−2) was applied to cells, the ΔsigB mutant displayed a marked increase in sensitivity to light compared to the wild type. To investigate the role of the blue-light sensor Lmo0799, mutants were constructed that either had a deletion of the gene (Δlmo0799) or alteration in a conserved cysteine residue at position 56, which is predicted to play a pivotal role in the photocycle of the protein (lmo0799 C56A). Both mutants displayed phenotypes similar to the ΔsigB mutant in the presence of blue light, providing genetic evidence that residue 56 is critical for light sensing in L. monocytogenes. Taken together, these results demonstrate that L. monocytogenes is inhibited by blue light in a manner that depends on reactive oxygen species, and they demonstrate clear light-dependent phenotypes associated with σB and the blue-light sensor Lmo0799. IMPORTANCE Listeria monocytogenes is a bacterial foodborne pathogen that can cause life-threatening infections in humans. It is known to be able to sense and respond to visible light. In this study, we examine the effects of blue light on the growth and survival of this pathogen. We show that growth can be inhibited at comparatively low doses of blue light, and that at higher doses, L. monocytogenes cells are killed. We present evidence suggesting that blue light inhibits this organism by causing the production of reactive oxygen species, such as hydrogen peroxide. We help clarify the mechanism of light sensing by constructing a “blind” version of the blue-light sensor protein. Finally, we show that activation of the general stress response by light has a negative effect on growth, probably because cellular resources are diverted into protective mechanisms rather than growth. PMID:27129969

Design and characterization of thick InxGa1-xAs metamorphic buffer layers grown by hydride vapor phase epitaxy

NASA Astrophysics Data System (ADS)

Schulte, K. L.; Zutter, B. T.; Wood, A. W.; Babcock, S. E.; Kuech, T. F.

2014-03-01

Thick InxGa1-xAs metamorphic buffer layers (MBLs) grown by hydride vapor phase epitaxy (HVPE) were studied. Relationships between MBL properties and growth parameters such as grading rate, cap layer thickness, final xInAs, and deposition temperature (TD) were explored. The MBLs were characterized by measurement of in-plane residual strain (ɛ¦¦), surface etch pit density (EPD), and surface roughness. Capping layer thickness had a strong effect on strain relaxation, with thickly capped samples exhibiting the lowest ɛ¦¦. EPD was higher in samples with thicker caps, reflecting their increased relaxation through dislocation generation. ɛ¦¦ and EPD were weakly affected by the grading rate, making capping layer thickness the primary structural parameter which controls these properties. MBLs graded in discrete steps had similar properties to MBLs with continuous grading. In samples with identical thickness and 10-step grading style, ɛ¦¦ increased almost linearly with final xInAs, while total relaxation stayed relatively constant. Relaxation as a function of xInAs could be described by an equilibrium model in which dislocation nucleation is impeded by the energy of the existing dislocation array. EPD was constant from xInAs = 0 to 0.24 then increased exponentially, which is related to the increased dislocation interaction and blocking seen at higher dislocation densities. RMS roughness increased with xInAs above a certain strain rate (0.15%/µm) samples grown below this level possessed large surface hillocks and high roughness values. The elimination of hillocks at higher values of xInAs is attributed to increased density of surface steps and is related to the out-of-plane component of the burgers vector of the dominant type of 60° dislocation. TD did not affect ɛ¦¦ for samples with a given xInAs. EPD tended to increase with TD, indicating dislocation glide likely is impeded at higher temperatures.

Perspective of Life Search in Martian Econiches

NASA Astrophysics Data System (ADS)

Demidov, N. E.

2017-05-01

Mars may be divided on five ecological niches according to presence and state of water: permanent polar caps, dry regolith, subpermafrost aquifers, cryopegs and ice containing regolith. Basic limiting factors for the search of life in this econiches are: absence of water (dry regolith), depth of burial (cryopegs and subpermafrost aquifers), age (ice containing permafrost and polar caps). High priority targets for the search of life on Mars are represented by permanently frozen deposits of young polar volcanoes and ash layers in polar caps. During volcanic eruptions microorganisms from subpermafrost aquifers could propagate to the surface and survive in permafrost or ice for million years, as it is known to happen on Earth. Possibility of specific lithic habitats in dry layer must also be taken into account.

Thermal annealing studies of GeTe-Sb2Te3 alloys with multiple interfaces

NASA Astrophysics Data System (ADS)

Bragaglia, Valeria; Mio, Antonio M.; Calarco, Raffaella

2017-08-01

A high degree of vacancy ordering is obtained by annealing amorphous GeTe-Sb2Te3 (GST) alloys deposited on a crystalline substrate, which acts as a template for the crystallization. Under annealing the material evolves from amorphous to disordered rocksalt, to ordered rocksalt with vacancies arranged into (111) oriented layers, and finally converts into the stable trigonal phase. The role of the interface in respect to the formation of an ordered crystalline phase is studied by comparing the transformation stages of crystalline GST with and without a capping layer. The capping layer offers another crystallization interface, which harms the overall crystalline quality.

Oxidation preventative capping layer for deep-ultra-violet and soft x-ray multilayers

DOEpatents

Prisbrey, Shon T.

2004-07-06

The invention uses iridium and iridium compounds as a protective capping layer on multilayers having reflectivity in the deep ultra-violet to soft x-ray regime. The iridium compounds can be formed in one of two ways: by direct deposition of the iridium compound from a prepared target or by depositing a thin layer (e.g., 5-50 angstroms) of iridium directly onto an element. The deposition energy of the incoming iridium is sufficient to activate the formation of the desired iridium compound. The compounds of most interest are iridium silicide (IrSi.sub.x) and iridium molybdenide (IrMo.sub.x).

BEOL compatible high tunnel magneto resistance perpendicular magnetic tunnel junctions using a sacrificial Mg layer as CoFeB free layer cap

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swerts, J., E-mail: Johan.Swerts@imec.be; Mertens, S.; Lin, T.

Perpendicularly magnetized MgO-based tunnel junctions are envisaged for future generation spin-torque transfer magnetoresistive random access memory devices. Achieving a high tunnel magneto resistance and preserving it together with the perpendicular magnetic anisotropy during BEOL CMOS processing are key challenges to overcome. The industry standard technique to deposit the CoFeB/MgO/CoFeB tunnel junctions is physical vapor deposition. In this letter, we report on the use of an ultrathin Mg layer as free layer cap to protect the CoFeB free layer from sputtering induced damage during the Ta electrode deposition. When Ta is deposited directly on CoFeB, a fraction of the surface ofmore » the CoFeB is sputtered even when Ta is deposited with very low deposition rates. When depositing a thin Mg layer prior to Ta deposition, the sputtering of CoFeB is prevented. The ultra-thin Mg layer is sputtered completely after Ta deposition. Therefore, the Mg acts as a sacrificial layer that protects the CoFeB from sputter-induced damage during the Ta deposition. The Ta-capped CoFeB free layer using the sacrificial Mg interlayer has significantly better electrical and magnetic properties than the equivalent stack without protective layer. We demonstrate a tunnel magneto resistance increase up to 30% in bottom pinned magnetic tunnel junctions and tunnel magneto resistance values of 160% at resistance area product of 5 Ω.μm{sup 2}. Moreover, the free layer maintains perpendicular magnetic anisotropy after 400 °C annealing.« less

Pervaporation dehydration of ethanol by hyaluronic acid/sodium alginate two-active-layer composite membranes.

PubMed

Gao, Chengyun; Zhang, Minhua; Ding, Jianwu; Pan, Fusheng; Jiang, Zhongyi; Li, Yifan; Zhao, Jing

2014-01-01

The composite membranes with two-active-layer (a capping layer and an inner layer) were prepared by sequential spin-coatings of hyaluronic acid (HA) and sodium alginate (NaAlg) on the polyacrylonitrile (PAN) support layer. The SEM showed a mutilayer structure and a distinct interface between the HA layer and the NaAlg layer. The coating sequence of two-active-layer had an obvious influence on the pervaporation dehydration performance of membranes. When the operation temperature was 80 °C and water concentration in feed was 10 wt.%, the permeate fluxes of HA/Alg/PAN membrane and Alg/HA/PAN membrane were similar, whereas the separation factor were 1130 and 527, respectively. It was found that the capping layer with higher hydrophilicity and water retention capacity, and the inner layer with higher permselectivity could increase the separation performance of the composite membranes. Meanwhile, effects of operation temperature and water concentration in feed on pervaporation performance as well as membrane properties were studied. Copyright © 2013 Elsevier Ltd. All rights reserved.

Study on influences of TiN capping layer on time-dependent dielectric breakdown characteristic of ultra-thin EOT high-k metal gate NMOSFET with kMC TDDB simulations

NASA Astrophysics Data System (ADS)

Xu, Hao; Yang, Hong; Luo, Wei-Chun; Xu, Ye-Feng; Wang, Yan-Rong; Tang, Bo; Wang, Wen-Wu; Qi, Lu-Wei; Li, Jun-Feng; Yan, Jiang; Zhu, Hui-Long; Zhao, Chao; Chen, Da-Peng; Ye, Tian-Chun

2016-08-01

The thickness effect of the TiN capping layer on the time dependent dielectric breakdown (TDDB) characteristic of ultra-thin EOT high-k metal gate NMOSFET is investigated in this paper. Based on experimental results, it is found that the device with a thicker TiN layer has a more promising reliability characteristic than that with a thinner TiN layer. From the charge pumping measurement and secondary ion mass spectroscopy (SIMS) analysis, it is indicated that the sample with the thicker TiN layer introduces more Cl passivation at the IL/Si interface and exhibits a lower interface trap density. In addition, the influences of interface and bulk trap density ratio N it/N ot are studied by TDDB simulations through combining percolation theory and the kinetic Monte Carlo (kMC) method. The lifetime reduction and Weibull slope lowering are explained by interface trap effects for TiN capping layers with different thicknesses. Project supported by the National High Technology Research and Development Program of China (Grant No. SS2015AA010601), the National Natural Science Foundation of China (Grant Nos. 61176091 and 61306129), and the Opening Project of Key Laboratory of Microelectronics Devices & Integrated Technology, Institute of MicroElectronics of Chinese Academy of Sciences.

Millimeter-wave monolithic diode-grid frequency multiplier

NASA Technical Reports Server (NTRS)

Maserjian, Joseph (Inventor)

1990-01-01

A semiconductor diode structure useful for harmonic generation of millimeter or submillimeter wave radiation from a fundamental input wave is fabricated on a GaAs substrate. A heavily doped layer of n(sup ++) GaAs is produced on the substrate and then a layer of intrinsic GaAs on said heavily doped layer on top of which a sheet of heavy doping (++) is produced. A thin layer of intrinsic GaAs grown over the sheet is capped with two metal contacts separated by a gap to produce two diodes connected back to back through the n(sup ++) layer for multiplication of frequency by an odd multiple. If only one metal contact caps the thin layer of intrinsic GaAs, the second diode contact is produced to connect to the n(sup ++) layer for multiplication of frequency by an even number. The odd or even frequency multiple is selected by a filter. A phased array of diodes in a grid will increase the power of the higher frequency generated.

Improving the electrical properties of lanthanum silicate films on ge metal oxide semiconductor capacitors by adopting interfacial barrier and capping layers.

PubMed

Choi, Yu Jin; Lim, Hajin; Lee, Suhyeong; Suh, Sungin; Kim, Joon Rae; Jung, Hyung-Suk; Park, Sanghyun; Lee, Jong Ho; Kim, Seong Gyeong; Hwang, Cheol Seong; Kim, HyeongJoon

2014-05-28

The electrical properties of La-silicate films grown by atomic layer deposition (ALD) on Ge substrates with different film configurations, such as various Si concentrations, Al2O3 interfacial passivation layers, and SiO2 capping layers, were examined. La-silicate thin films were deposited using alternating injections of the La[N{Si(CH3)3}2]3 precursor with O3 as the La and O precursors, respectively, at a substrate temperature of 310 °C. The Si concentration in the La-silicate films was further controlled by adding ALD cycles of SiO2. For comparison, La2O3 films were also grown using [La((i)PrCp)3] and O3 as the La precursor and oxygen source, respectively, at the identical substrate temperature. The capacitance-voltage (C-V) hysteresis decreased with an increasing Si concentration in the La-silicate films, although the films showed a slight increase in the capacitance equivalent oxide thickness. The adoption of Al2O3 at the interface as a passivation layer resulted in lower C-V hysteresis and a low leakage current density. The C-V hysteresis voltages of the La-silicate films with Al2O3 passivation and SiO2 capping layers was significantly decreased to ∼0.1 V, whereas the single layer La-silicate film showed a hysteresis voltage as large as ∼1.0 V.

Observations of the northern seasonal polar cap on Mars: I. Spring sublimation activity and processes

USGS Publications Warehouse

Hansen, C.J.; Byrne, S.; Portyankina, G.; Bourke, M.; Dundas, C.; McEwen, A.; Mellon, M.; Pommerol, A.; Thomas, N.

2013-01-01

Spring sublimation of the seasonal CO2 northern polar cap is a dynamic process in the current Mars climate. Phenomena include dark fans of dune material propelled out onto the seasonal ice layer, polygonal cracks in the seasonal ice, sand flow down slipfaces, and outbreaks of gas and sand around the dune margins. These phenomena are concentrated on the north polar erg that encircles the northern residual polar cap. The Mars Reconnaissance Orbiter has been in orbit for three Mars years, allowing us to observe three northern spring seasons. Activity is consistent with and well described by the Kieffer model of basal sublimation of the seasonal layer of ice applied originally in the southern hemisphere. Three typical weak spots have been identified on the dunes for escape of gas sublimed from the bottom of the seasonal ice layer: the crest of the dune, the interface of the dune with the interdune substrate, and through polygonal cracks in the ice. Pressurized gas flows through these vents and carries out material entrained from the dune. Furrows in the dunes channel gas to outbreak points and may be the northern equivalent of southern radially-organized channels (“araneiform” terrain), albeit not permanent. Properties of the seasonal CO2 ice layer are derived from timing of seasonal events such as when final sublimation occurs. Modification of dune morphology shows that landscape evolution is occurring on Mars today, driven by seasonal activity associated with sublimation of the seasonal CO2 polar cap.

Achieving high carrier mobility exceeding 70 cm2/Vs in amorphous zinc tin oxide thin-film transistors

NASA Astrophysics Data System (ADS)

Kim, Sang Tae; Shin, Yeonwoo; Yun, Pil Sang; Bae, Jong Uk; Chung, In Jae; Jeong, Jae Kyeong

2017-09-01

This paper proposes a new defect engineering concept for low-cost In- and Ga-free zinc tin oxide (ZTO) thin-film transistors (TFTs). This concept is comprised of capping ZTO films with tantalum (Ta) and a subsequent modest thermal annealing treatment at 200 °C. The Ta-capped ZTO TFTs exhibited a remarkably high carrier mobility of 70.8 cm2/Vs, low subthreshold gate swing of 0.18 V/decade, threshold voltage of -1.3 V, and excellent ION/OFF ratio of 2 × 108. The improvement (> two-fold) in the carrier mobility compared to the uncapped ZTO TFT can be attributed to the effective reduction of the number of adverse tailing trap states, such as hydroxyl groups or oxygen interstitial defects, which stems from the scavenging effect of the Ta capping layer on the ZTO channel layer. Furthermore, the Ta-capped ZTO TFTs showed excellent positive and negative gate bias stress stabilities. [Figure not available: see fulltext.

Quasi-periodic climatic changes on Mars and earth

NASA Technical Reports Server (NTRS)

Cutts, J. A.; Pollack, J. B.; Toon, O. B.; Howard, A. D.

1981-01-01

Evidence of climatic changes on Mars and the earth due to geologic and astronomical variations is discussed. Finely striped ice-free bands in the Martian polar caps have been taken to indicate that long term variations in the orbit and axial tilt of Mars have precipitated these features at the rate of a mm/yr. Photogrammetric and photometric methods have contributed to measurements of the composition and depth of the Martian caps (14-46 m), and observations of higher solar energy absorption in the northern ice cap implies greater dust deposition in that region than on the south cap; however, the transport mechanisms are not well understood. Comparisons of earth and Martian climatic variations data are made, noting a lack of information on the age intervals of marine and nonmarine sediments on the earth. The possibilities of using quantitative data other than layer thickness to constrain climate models are discussed, and the slope or albedo of layers, or the spacing of polar undulations are suggested.

Application of Carbon Nanomaterials in Lithium-Ion Battery Electrodes

NASA Astrophysics Data System (ADS)

Jaber-Ansari, Laila

Carbon nanomaterials such as single-walled carbon nanotubes (SWCNTs) and graphene have emerged as leading additives for high capacity nanocomposite lithium ion battery electrodes due to their ability to improve electrode conductivity, current collection efficiency, and charge/discharge rate for high power applications. In this work, the these nanomaterials have been developed and their properties have been fine-tuned to help solve fundamental issues in conventional lithium ion battery electrodes. Towards this end, the application of SWCNTs in lithium-ion anodes has been studied. As-grown SWCNTs possess a distribution of physical and electronic structures, and it is of high interest to determine which subpopulations of SWCNTs possess the highest lithiation capacity and to develop processing methods that can enhance the lithiation capacity of underperforming SWCNT species. Towards this end, SWCNT electronic type purity is controlled via density gradient ultracentrifugation, enabling a systematic study of the lithiation of SWCNTs as a function of metal versus semiconducting content. Experimentally, vacuum filtered freestanding films of metallic SWCNTs are found to accommodate lithium with an order of magnitude higher capacity than their semiconducting counterparts. In contrast, SWCNT film densification leads to the enhancement of the lithiation capacity of semiconducting SWCNTs to levels comparable to metallic SWCNTs, which is corroborated by theoretical calculations. To understand the interaction of the graphene with lithium ions and electrolyte species during electrochemical we use Raman spectroscopy in a model system of monolayer graphene transferred on a Si(111) substrate and density functional theory (DFT) to investigate defect formation as a function of lithiation. This model system enables the early stages of defect formation to be probed in a manner previously not possible with commonly-used reduced graphene oxide or multilayer graphene substrates. Using ex situ and Ar-atmosphere Raman spectroscopy, a rapid increase in graphene defect level is detected for small increments in the number of lithiation/delithiation cycles until the I(D)/I(G) ratio reaches ˜1.5-2.0 and the 2D peak intensity drops by ˜50%, after which the Raman spectra show minimal changes upon further cycling. Using DFT, the interplay between graphene topological defects and chemical functionalization is explored, thus providing insight into the experimental results. In particular, the DFT results show that defects can act as active sites for species that are present in the electrochemical environment such as Li, O, and F. Furthermore, chemical functionalization with these species lowers subsequent defect formation energies, thus accelerating graphene degradation upon cycling. This positive feedback loop continues until the defect concentration reaches a level where lithium diffusion through the graphene can occur in a relatively unimpeded manner, with minimal further degradation upon extended cycling. Overall, this study provides mechanistic insight into graphene defect formation during lithiation, thus informing ongoing efforts to employ graphene in lithium ion battery technology. Having understood the electrochemical properties of graphene, we have used this to improve the performance of Li-ion cathodes. In particular, Spinel-structured LiMn2O4 (LMO) is a desirable cathode material for Li-ion batteries due to its low cost, thermal stability (safety) and high power capability. However, LMO suffers from a limited cycle life that is triggered by manganese dissolution into the electrolyte during electrochemical cycling. Here, we show that a single sheet of graphene can act effectively as a diffusion barrier for Mn2+ ions, thereby protecting the cathode surface and significantly reducing the dissolution process. Relative to lithium cells containing a sputtered and uncoated thin film LMO 'control' cathode, cells with a graphene-coated LMO cathode provide approximately three times the capacity with significantly superior cycling stability and power. X-ray photoelectron spectroscopy (XPS) depth profiling provides evidence that the graphene coating inhibits manganese depletion from the LMO surface. Furthermore, cross-section transmission electron microscopy (TEM) demonstrates that a stable solid electrolyte interphase (SEI) layer is formed on graphene, which screens the LMO from direct contact with the electrolyte, thereby prolonging the electrode life. Density functional theory (DFT) calculations support the hypothesis of graphene as a diffusion barrier: Defected graphene acts as a barrier for manganese diffusion while allowing the transport of lithium. However, DFT calculations also suggest that the role of graphene goes beyond a physical barrier. The reactive edge of graphene can chemically interact with Mn3+ at the electrode surface, promotes an oxidation state change (Mn3+→Mn4+) and suppresses dissolution and the Jahn-Teller distortion associated with Mn 3.

In Situ Stress Evolution in Li 1+x Mn 2 O 4 Thin Films during Electrochemical Cycling in Li-Ion Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheth, Jay; Karan, Naba K.; Abraham, Daniel P.

2016-01-01

Real time monitoring of stress evolution in electrodes during electrochemical cycling can help quantify the driving forces that dictate their mechanical degradation. In the present work, in-situ stress evolution in thin films of spinel Li 1+x Mn 2 O 4 (LMO) was measured by monitoring the change in the elastic substrate curvature during electrochemical cycling in a specially designed beaker cell in the 3.5–4.3 V (vs. Li/Li+) voltage range. The LMO thin films were prepared using a solution deposition technique and their structures and morphologies were characterized by X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM). The stressmore » evolution in the early part of the first delithiation cycle (<4.05 V) was consistent with the XRD data. However, stress evolution during later stages of the first delithiation cycle (>4.05 V) was not consistent with the XRD results, and showed irreversible behavior, suggesting irreversible changes in the electrode. Beyond the first delithiation cycle, the stress evolution was reversible, with a steady buildup of compressive and tensile stress during lithium insertion and extraction, respectively. Measurements on LMO films of varying thicknesses suggest that the first cycle irreversibility in stress response arises primarily from the electrode bulk.« less

Electrochemical and Electronic Charge Transport Properties of Ni-Doped LiMn₂O₄ Spinel Obtained from Polyol-Mediated Synthesis.

PubMed

Yang, Shuo; Schmidt, Dirk Oliver; Khetan, Abhishek; Schrader, Felix; Jakobi, Simon; Homberger, Melanie; Noyong, Michael; Paulus, Anja; Kungl, Hans; Eichel, Rüdiger-Albert; Pitsch, Heinz; Simon, Ulrich

2018-05-16

LiNi 0.5 Mn 1.5 O₄ (LNMO) spinel has been extensively investigated as one of the most promising high-voltage cathode candidates for lithium-ion batteries. The electrochemical performance of LNMO, especially its rate performance, seems to be governed by its crystallographic structure, which is strongly influenced by the preparation methods. Conventionally, LNMO materials are prepared via solid-state reactions, which typically lead to microscaled particles with only limited control over the particle size and morphology. In this work, we prepared Ni-doped LiMn₂O₄ (LMO) spinel via the polyol method. The cycling stability and rate capability of the synthesized material are found to be comparable to the ones reported in literature. Furthermore, its electronic charge transport properties were investigated by local electrical transport measurements on individual particles by means of a nanorobotics setup in a scanning electron microscope, as well as by performing DFT calculations. We found that the scarcity of Mn 3+ in the LNMO leads to a significant decrease in electronic conductivity as compared to undoped LMO, which had no obvious effect on the rate capability of the two materials. Our results suggest that the rate capability of LNMO and LMO materials is not limited by the electronic conductivity of the fully lithiated materials.

Rocket measurements within a polar cap arc - Plasma, particle, and electric circuit parameters

NASA Technical Reports Server (NTRS)

Weber, E. J.; Ballenthin, J. O.; Basu, S.; Carlson, H. C.; Hardy, D. A.; Maynard, N. C.; Kelley, M. C.; Fleischman, J. R.; Pfaff, R. F.

1989-01-01

Results are presented from the Polar Ionospheric Irregularities Experiment (PIIE), conducted from Sondrestrom, Greenland, on March 15, 1985, designed for an investigation of processes which lead to the generation of small-scale (less than 1 km) ionospheric irregularities within polar-cap F-layer auroras. An instrumented rocket was launched into a polar cap F layer aurora to measure energetic electron flux, plasma, and electric circuit parameters of a sun-aligned arc, coordinated with simultaneous measurements from the Sondrestrom incoherent scatter radar and the AFGL Airborne Ionospheric Observatory. Results indicated the existence of two different generation mechanisms on the dawnside and duskside of the arc. On the duskside, parameters are suggestive of an interchange process, while on the dawnside, fluctuation parameters are consistent with a velocity shear instability.

Assembly of Layered Monetite-Chitosan Nanocomposite and Its Transition to Organized Hydroxyapatite.

PubMed

Ruan, Qichao; Liberman, David; Zhang, Yuzheng; Ren, Dongni; Zhang, Yunpeng; Nutt, Steven; Moradian-Oldak, Janet

2016-06-13

Bioinspired synthesis of hierarchically structured calcium phosphate (CaP) material is a highly promising strategy for developing improved bone substitute materials. However, synthesis of CaP materials with outstanding mechanical properties still remains an ongoing challenge. Inspired by the formation of lamellar structure in nacre, we designed an organic matrix composed of chitosan and cis-butenediolic acid (maleic acid, MAc) that could assemble into a layered complex and further guide the mineralization of monetite crystals, resulting in the formation of organized and parallel arrays of monetite platelets with a brick-and-mortar structure. Using the layered monetite-chitosan composite as a precursor, we were able to synthesize hydroxyapatite (HAp) with multiscale hierarchically ordered structure via a topotactic phase transformation process. On the nanoscale, needlelike HAp crystallites assembled into organized bundles that aligned to form highly oriented plates on the microscale. On the large-scale level, these plates with different crystal orientations were stacked together to form a layered structure. The organized structures and composite feature yielded CaP materials with improved mechanical properties close to those of bone. Our study introduces a biomimetic approach that may be practical for the design of advanced, mechanically robust materials for biomedical applications.

Casein Aggregates Built Step-by-Step on Charged Polyelectrolyte Film Surfaces Are Calcium Phosphate-cemented*

PubMed Central

Nagy, Krisztina; Pilbat, Ana-Maria; Groma, Géza; Szalontai, Balázs; Cuisinier, Frédéric J. G.

2010-01-01

The possible mechanism of casein aggregation and micelle buildup was studied in a new approach by letting α-casein adsorb from low concentration (0.1 mg·ml−1) solutions onto the charged surfaces of polyelectrolyte films. It was found that α-casein could adsorb onto both positively and negatively charged surfaces. However, only when its negative phosphoseryl clusters remained free, i.e. when it adsorbed onto a negative surface, could calcium phosphate (CaP) nanoclusters bind to the casein molecules. Once the CaP clusters were in place, step-by-step building of multilayered casein architectures became possible. The presence of CaP was essential; neither Ca2+ nor phosphate could alone facilitate casein aggregation. Thus, it seems that CaP is the organizing motive in the casein micelle formation. Atomic force microscopy revealed that even a single adsorbed casein layer was composed of very small (in the range of tens of nanometers) spherical forms. The stiffness of the adsorbed casein layer largely increased in the presence of CaP. On this basis, we can imagine that casein micelles emerge according to the following scheme. The amphipathic casein monomers aggregate into oligomers via hydrophobic interactions even in the absence of CaP. Full scale, CaP-carrying micelles could materialize by interlocking these casein oligomers with CaP nanoclusters. Such a mechanism would not contradict former experimental results and could offer a synthesis between the submicelle and the block copolymer models of casein micelles. PMID:20921229

Magnetospheric convection and the high-latitude F2 ionosphere

NASA Technical Reports Server (NTRS)

Knudsen, W. C.

1974-01-01

Behavior of the polar ionospheric F layer as it is convected through the cleft, over the polar cap, and through the nightside F layer trough zone is investigated. Passage through the cleft adds approximately 200,000 ions per cu cm in the vicinity of the F2 peak and redistributes the ionization above approximately 400-km altitude to conform with an increased electron temperature. The redistribution of ionization above 400-km altitude forms the 'averaged' plasma ring seen at 1000-km altitude. The F layer is also raised by approximately 20 km in altitude by the convection electric field. The time required for passage across the polar cap (25 deg) is about the same as that required for the F layer peak concentration to decay by e. The F layer response to passage through the nightside soft electron precipitation zone should be similar to but less than its response to passage through the cleft.

Structural enhancement of ZnO on SiO2 for photonic applications

NASA Astrophysics Data System (ADS)

Ruth, Marcel; Meier, Cedrik

2013-07-01

Multi-layer thin films are often the basis of photonic devices. Zinc oxide (ZnO) with its excellent optoelectronic properties can serve as a high quality emitter in structures like microdisks or photonic crystals. Here, we present a detailed study on the enhancement of the structural properties of low-temperature MBE grown ZnO on silica (SiO2). By thermal annealing a grain coalescence of the initially polycrystalline layer leads to an enhancement of the electronic structure, indicated by a blue shift of the photoluminescence (PL) signal maximum. Oxygen atmosphere during the annealing process prevents the creation of intrinsic defects by out-diffusion. Pre-annealing deposited SiO2 capping layers instead obstruct the recrystallization and lead to less intense emission. While thin capping layers partially detach from the ZnO film at high temperatures and cause higher surface roughness and the weakest emission, thicker layers remain smoother and exhibit a significantly stronger photoluminescence.

KSC-04pd0621

NASA Image and Video Library

2004-03-24

KENNEDY SPACE CENTER, FLA. -- In the Thermal Protection System Facility, Pilar Ryan, with United Space Alliance, stitches a piece of insulation blanket for Atlantis' nose cap. Behind her is a cover for the nose cap. The blankets consist of layered, pure silica felt sandwiched between a layer of silica fabric (the hot side) and a layer of S-Glass fabric. The blankets are semi-rigid and can be made as large as 30 inches by 30 inches. The blanket is through-stitched with pure silica thread in a 1-inch grid pattern. After fabrication, the blanket is bonded directly to the vehicle structure and finally coated with a high purity silica coating that improves erosion resistance.

Mutation analysis of FANCD2, BRIP1/BACH1, LMO4 and SFN in familial breast cancer.

PubMed

Lewis, Aaron G; Flanagan, James; Marsh, Anna; Pupo, Gulietta M; Mann, Graham; Spurdle, Amanda B; Lindeman, Geoffrey J; Visvader, Jane E; Brown, Melissa A; Chenevix-Trench, Georgia

2005-01-01

Mutations in known predisposition genes account for only about a third of all multiple-case breast cancer families. We hypothesized that germline mutations in FANCD2, BRIP1/BACH1, LMO4 and SFN may account for some of the unexplained multiple-case breast cancer families. The families used in this study were ascertained through the Kathleen Cuningham Foundation Consortium for Research into Familial Breast Cancer (kConFab). Denaturing high performance liquid chromatography (DHPLC) analysis of the coding regions of these four genes was conducted in the youngest affected cases of 30 to 267 non-BRCA1/2 breast cancer families. In addition, a further 399 index cases were also screened for mutations in two functionally significant regions of the FANCD2 gene and 253 index cases were screened for two previously reported mutations in BACH1 (p. P47A and p. M299I). DHPLC analysis of FANCD2 identified six silent exonic variants, and a large number of intronic variants, which tagged two common haplotypes. One protein truncating variant was found in BRIP1/BACH1, as well as four missense variants, a silent change and a variant in the 3' untranslated region. No missense or splice site mutations were found in LMO4 or SFN. Analysis of the missense, silent and frameshift variants of FANCD2 and BACH1 in relatives of the index cases, and in a panel of controls, found no evidence suggestive of pathogenicity. There is no evidence that highly penetrant exonic or splice site mutations in FANCD2, BRIP1/BACH1, LMO4 or SFN contribute to familial breast cancer. Large scale association studies will be necessary to determine whether any of the polymorphisms or haplotypes identified in these genes contributes to breast cancer risk.

Tiny Device Mimics Human Lung Function

ScienceCinema

McDonald, Rebecca; Harris, Jennifer; Nath, Pulak

2018-01-16

Scientists at Los Alamos National Laboratory are developing a miniature, tissue-engineered artificial lung that mimics the response of the human lung to drugs, toxins and other agents. “We breathe in and out thousands of times every day. And while we have control over what we eat or drink, we don’t always have control over what we breathe in,” said Jennifer Harris of Biosecurity and Public Health at Los Alamos, "and so we’re making this miniature lung to be able to test on actual human cells whether something in the environment, or a drug, is toxic or harmful to us." Nicknamed “PuLMo” for Pulmonary Lung Model (Pulmo is also the Latin word for "lung")the device consists of two major parts, the bronchiolar unit and the alveolar unit—just like the human lung. The units are primarily made from various polymers and are connected by a microfluidic “circuit board” that manages fluid and air flow. “When we build our lung, we not only take into account the aspects of different cell types, the tissues that are involved, we also take into account that a lung is supposed to breathe, so PuLMo actually breathes,” said Pulak Nath of Applied Modern Physics, who leads engineering efforts for the project. The most exciting application of PuLMo is a potentially revolutionary improvement in the reliability of drug-toxicity assessments and the prediction of new pharmaceutical success in humans, according to Harris. The PuLMo may also be designed to mimic lung disease conditions, such as Chronic Obstructive Pulmonary Disease (COPD) and asthma, and may be used to study lung air-flow dynamics to better understand the mechanisms of toxins and drug delivery and the effects of smoking, particularly the less-understood effects of e-cigarettes.

The Age of the Moon

NASA Astrophysics Data System (ADS)

Barboni, M.; Boehnke, P.; Keller, C. B.; Kohl, I. E.; McKeegan, K. D.; Schoene, B.; Young, E. D.

2016-12-01

Knowledge of the age of the Moon is important for understanding the early evolution of the solar system, including the timing of the hypothesized Giant Impact (GI). There have been many attempts to determine the Moon's age, but significant disagreement remains with some authors favoring an early formation and others arguing for a relatively young Moon formed at 4.4 Ga. Attempts to date the GI indirectly through its effects on the asteroid belt are problematic as there is no way to uniquely ascertain the cause of the observed disturbances (e.g., GI or meteorite parent body breakup). Determining the timing of the Lunar Magma Ocean (LMO) crystallization provides a more direct constraint on the age of the Moon, but interpreting the chronologic significance of LMO products is complicated by the fact that the only rock samples available are breccias. A better approach is to construct a model age for the fractional crystallization of the LMO since this should provide a global signature. Zircons from the Apollo samples are ancient, robust against later disturbances, and amenable to precise U-Pb geochronology and Hf isotope analyses that can be used to construct Lu-Hf model ages for the silicate differentiation of the Moon. Previous isotopic studies of Apollo zircons yielded artificially young Hf model ages because of the (then unknown) effect of neutron capture on Hf isotopic ratios generated by long exposure to cosmic radiation, and were unable to determine whether or not the U-Pb dates were concordant due to insufficient precision of in situ dating techniques. We have addressed these issues by carrying out CA-ID-TIMS U-Pb geochronology on Apollo 14 zircon fragments, followed by Hf isotope determination by solution MC-ICP-MS on the same volume of zircon. By constructing Hf model ages from zircons that are concordant to the sub-permil level, we show that the minimum age for the end of differentiation of the LMO, and by extension, the formation of the Moon, is 4.52 ± 0.01 Ga.

Blue and Red Light Modulates SigB-Dependent Gene Transcription, Swimming Motility and Invasiveness in Listeria monocytogenes

PubMed Central

Ondrusch, Nicolai; Kreft, Jürgen

2011-01-01

Background In a number of gram-positive bacteria, including Listeria, the general stress response is regulated by the alternative sigma factor B (SigB). Common stressors which lead to the activation of SigB and the SigB-dependent regulon are high osmolarity, acid and several more. Recently is has been shown that also blue and red light activates SigB in Bacillus subtilis. Methodology/Principal Findings By qRT-PCR we analyzed the transcriptional response of the pathogen L. monocytogenes to blue and red light in wild type bacteria and in isogenic deletion mutants for the putative blue-light receptor Lmo0799 and the stress sigma factor SigB. It was found that both blue (455 nm) and red (625 nm) light induced the transcription of sigB and SigB-dependent genes, this induction was completely abolished in the SigB mutant. The blue-light effect was largely dependent on Lmo0799, proving that this protein is a genuine blue-light receptor. The deletion of lmo0799 enhanced the red-light effect, the underlying mechanism as well as that of SigB activation by red light remains unknown. Blue light led to an increased transcription of the internalin A/B genes and of bacterial invasiveness for Caco-2 enterocytes. Exposure to blue light also strongly inhibited swimming motility of the bacteria in a Lmo0799- and SigB-dependent manner, red light had no effect there. Conclusions/Significance Our data established that visible, in particular blue light is an important environmental signal with an impact on gene expression and physiology of the non-phototrophic bacterium L. monocytogenes. In natural environments these effects will result in sometimes random but potentially also cyclic fluctuations of gene activity, depending on the light conditions prevailing in the respective habitat. PMID:21264304

Tunable self-organization of nanocomposite multilayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, C. Q.; Pei, Y. T.; Shaha, K. P.

In this letter we report the controlled growth and microstructural evolution of self-assembled nanocomposite multilayers that are induced by surface ion-impingement. The nanoscale structures together with chemical composition, especially at the growing front, have been investigated with high-resolution transmission electron microscopy. Concurrent ion impingement of growing films produces an amorphous capping layer 3 nm in thickness where spatially modulated phase separation is initiated. It is shown that the modulation of multilayers as controlled by the self-organization of nanocrystallites below the capping layer, can be tuned through the entire film.

Measurements and Modeling of Turbulent Fluxes during Persistent Cold Air Pool Events in Salt Lake Valley, Utah

NASA Astrophysics Data System (ADS)

Ivey, C. E.; Sun, X.; Holmes, H.

2017-12-01

Land surface processes are important in meteorology and climate research since they control the partitioning of surface energy and water exchange at the earth's surface. The surface layer is coupled to the planetary boundary layer (PBL) by surface fluxes, which serve as sinks or sources of energy, moisture, momentum, and atmospheric pollutants. Quantifying the surface heat and momentum fluxes at the land-atmosphere interface, especially for different surface land cover types, is important because they can further influence the atmospheric dynamics, vertical mixing, and transport processes that impact local, regional, and global climate. A cold air pool (CAP) forms when a topographic depression (i.e., valley) fills with cold air, where the air in the stagnant layer is colder than the air aloft. Insufficient surface heating, which is not able to sufficiently erode the temperature inversion that forms during the nighttime stable boundary layer, can lead to the formation of persistent CAPs during wintertime. These persistent CAPs can last for days, or even weeks, and are associated with increased air pollution concentrations. Thus, realistic simulations of the land-atmosphere exchange are meaningful to achieve improved predictions of the accumulation, transport, and dispersion of air pollution concentrations. The focus of this presentation is on observations and modeling results using turbulence data collected in Salt Lake Valley, Utah during the 2010-2011 wintertime Persistent Cold Air Pool Study (PCAPS). Turbulent fluxes and the surface energy balance over seven land use types are quantified. The urban site has an energy balance ratio (EBR) larger than one (1.276). Negative Bowen ratio (-0.070) is found at the cropland site. In addition to turbulence observations, half-hourly WRF simulated net radiation, latent heat, sensible heat, ground heat fluxes during one persistent CAP event are evaluated using the PCAPS observations. The results show that sensible and latent heat fluxes during the CAP event are overestimated. The sensitivity of WRF results to large-scale forcing datasets, PBL schemes and land surface models (LSMs) are also investigated. The optimal WRF configuration for simulating surface turbulent fluxes and atmospheric mixing during CAP events is determined.

EFFICIENCY OF CAPPING CONTAMINATED SEDIMENTS IN SITU: 2. MATHEMATICS OF DIFFUSION-ADSORPTION IN THE CAPPING LAYER. (R825513C009)

EPA Science Inventory

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

Can the Solid State Greenhouse Effect Produce ~100 Year Cycles in the Mars South Polar Residual CO2 Ice Cap?

NASA Astrophysics Data System (ADS)

Line, M. R.; Ingersoll, A. P.

2010-12-01

Malin et al. (2001) reported that the south perennial cap consists of quasi-circular pits ~8 meters deep, with a flat surface in between. The walls of the pits are retreating at a rate of 1 to 3 meters per year. Byrne and Ingersoll (2003a, 2003b) showed evidence that the floors of the pits are water ice and the upper layer is CO2. This layer will be gone in a few Martian centuries, if the observations are taken at face value. This raises some difficult questions: How likely is it that mankind would be witnessing the final few hundred years of the residual CO2 frost on Mars? Can one imagine extreme weather events that could recharge the residual CO2 frost once it is gone? Both seem unlikely, and we propose a different mechanism. Kieffer et al. (2000) showed that sunlight can penetrate several meters through the seasonal CO2 frost, where it warms the surface below. We have observational evidence that the same is happening in the perennial CO2 frost. Further, we have a model that shows how this "solid-state greenhouse" can lead to cyclic behavior, in which layers of CO2 build up on a water ice substrate, are heated internally by sunlight and lose mass from within. Eventually the layer becomes too weak to support itself, and it collapses to form pits. Then a new CO2 layer accumulates and the process repeats. Our study addresses fundamental questions of long-term stability of the Martian polar caps and how the caps control the atmospheric pressure. Instead of invoking extreme climate events to explain the data, we propose that processes within the frost itself can lead to cyclic growth and collapse of the pits. Our model implies that there is no long-term change in the ~8 meter layer of CO2 and no extreme weather events to make it change.

MLJ Computer Corner

ERIC Educational Resources Information Center

Brink, Dan

1987-01-01

Reviews the current state of printing software and printing hardware compatibility and capacity. Discusses the changing relationship between author and publisher resulting from the advent of desktop publishing. (LMO)

Liquid-phase-deposited siloxane-based capping layers for silicon solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Veith-Wolf, Boris; Wang, Jianhui; Hannu-Kuure, Milja

2015-02-02

We apply non-vacuum processing to deposit dielectric capping layers on top of ultrathin atomic-layer-deposited aluminum oxide (AlO{sub x}) films, used for the rear surface passivation of high-efficiency crystalline silicon solar cells. We examine various siloxane-based liquid-phase-deposited (LPD) materials. Our optimized AlO{sub x}/LPD stacks show an excellent thermal and chemical stability against aluminum metal paste, as demonstrated by measured surface recombination velocities below 10 cm/s on 1.3 Ωcm p-type silicon wafers after firing in a belt-line furnace with screen-printed aluminum paste on top. Implementation of the optimized LPD layers into an industrial-type screen-printing solar cell process results in energy conversion efficiencies ofmore » up to 19.8% on p-type Czochralski silicon.« less

Indirect excitation of ultrafast demagnetization

PubMed Central

Vodungbo, Boris; Tudu, Bahrati; Perron, Jonathan; Delaunay, Renaud; Müller, Leonard; Berntsen, Magnus H.; Grübel, Gerhard; Malinowski, Grégory; Weier, Christian; Gautier, Julien; Lambert, Guillaume; Zeitoun, Philippe; Gutt, Christian; Jal, Emmanuelle; Reid, Alexander H.; Granitzka, Patrick W.; Jaouen, Nicolas; Dakovski, Georgi L.; Moeller, Stefan; Minitti, Michael P.; Mitra, Ankush; Carron, Sebastian; Pfau, Bastian; von Korff Schmising, Clemens; Schneider, Michael; Eisebitt, Stefan; Lüning, Jan

2016-01-01

Does the excitation of ultrafast magnetization require direct interaction between the photons of the optical pump pulse and the magnetic layer? Here, we demonstrate unambiguously that this is not the case. For this we have studied the magnetization dynamics of a ferromagnetic cobalt/palladium multilayer capped by an IR-opaque aluminum layer. Upon excitation with an intense femtosecond-short IR laser pulse, the film exhibits the classical ultrafast demagnetization phenomenon although only a negligible number of IR photons penetrate the aluminum layer. In comparison with an uncapped cobalt/palladium reference film, the initial demagnetization of the capped film occurs with a delayed onset and at a slower rate. Both observations are qualitatively in line with energy transport from the aluminum layer into the underlying magnetic film by the excited, hot electrons of the aluminum film. Our data thus confirm recent theoretical predictions. PMID:26733106

Performance of greenhouse gas profiling by infrared-laser and microwave occultation in cloudy air

NASA Astrophysics Data System (ADS)

Proschek, V.; Kirchengast, G.; Emde, C.; Schweitzer, S.

2012-12-01

ACCURATE is a proposed future satellite mission enabling simultaneous measurements of greenhouse gases (GHGs), wind and thermodynamic variables from Low Earth Orbit (LEO). The measurement principle is a combination of LEO-LEO infrared-laser occultation (LIO) and microwave occultation (LMO), the LMIO method, where the LIO signals are very sensitive to clouds. The GHG retrieval will therefore be strongly influenced by clouds in parts of the troposphere. The IR-laser signals, at wavelengths within 2--2.5μ m, are chosen to measure six GHGs (H2O, CO2, CH4, N2O, O3, CO; incl.~key isotopes 13CO2, C18OO, HDO). The LMO signals enable to co-measure the thermodynamic variables. In this presentation we introduce the algorithm to retrieve GHG profiles under cloudy-air conditions by using quasi-realistic forward simulations, including also influence of Rayleigh scattering, scintillations and aerosols. Data from CALIPSO--Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations--with highest vertical resolution of about 60 m and horizontal resolution of about 330 m were used for simulation of clouds. The IR-laser signals consist for each GHG of a GHG-sensitive and a close-by reference signal. The key process, ``differencing'' of these two signals, removes the atmospheric ``broadband'' effects, resulting in a pure GHG transmission profile. Very thin ice clouds, like sub-visible cirrus, are fairly transparent to the IR-laser signals, thicker and liquid water clouds block the signals. The reference signal is used to produce a cloud layering profile from zero to blocking clouds and is smoothed in a preprocess to suppress scintillations. Sufficiently small gaps, of width <2 km in the cloud layering profile, are found to enable a decent retrieval of entire GHG profiles over the UTLS under broken cloudiness and are therefore bridged by interpolation. Otherwise in case of essentially continuous cloudiness the profiles are found to terminate at cloud top level. The accuracy of retrieved GHG profiles is found better than 1% to 4% for single profiles in the UTLS region outside clouds and through broken cloudiness, and the profiles are essentially unbiased. Cloud gap-interpolation increases the tropospheric penetration of GHG profiles for scientific applications. The associated cloud layering profile provides quality-control information on cloud gap-interpolations, if they occured, and on cloud-top altitude for cloud blocking cases. The LMIO technique shows promising prospects for GHG monitoring even under cloudy-air conditions.

Terahertz antireflection coating enabled by a subwavelength metallic mesh capped with a thin dielectric film

DOE PAGES

Huang, Li; Chen, Hou -Tong; Zeng, Beibei; ...

2016-03-30

Metamaterials/metasurfaces have enabled unprecedented manipulation of electromagnetic waves. Here we present a new design of metasurface structure functioning as antireflection coatings. The structure consists of a subwavelength metallic mesh capped with a thin dielectric layer on top of a substrate. By tailoring the geometric parameters of the metallic mesh and the refractive index and thickness of the capping dielectric film, reflection from the substrate can be completely eliminated at a specific frequency. Compared to traditional methods such as coatings with single- or multi-layer dielectric films, the metasurface antireflection coatings are much thinner and the requirement of index matching is largelymore » lifted. Here, this approach is particularly suitable for antireflection coatings in the technically challenging terahertz frequency range and is also applicable in other frequency regimes.« less

Reducing the effect of parasitic capacitance on implantable passive resonant sensors.

PubMed

Drazan, John F; Abdoun, Omar T; Wassick, Michael T; Marcus, George A; Dahle, Reena; Beardslee, Luke A; Cady, Nathaniel C; Ledet, Eric H

2016-08-01

Passive, LC resonators have the potential to serve as small, robust, low cost, implantable sensors to wirelessly monitor implants following orthopedic surgery. One significant barrier to using LC sensors is the influence on the sensor's resonance of the surrounding conductive high permittivity media in vivo. The surrounding media can detune the resonant frequency of the LC sensor resulting in a bias. To mitigate the effects of the surrounding media, we added a "capping layer" to LC sensors to isolate them from the surrounding media. Several capping materials and thicknesses were tested to determine effectiveness at reducing the sensor's interaction with the surrounding media. Results show that a 1 mm glass capping layer on the outer surfaces of the sensor was sufficient to reduce the effects of the media on sensor signal to less than 1%.

Black optic display

DOEpatents

Veligdan, James T.

1997-01-01

An optical display includes a plurality of stacked optical waveguides having first and second opposite ends collectively defining an image input face and an image screen, respectively, with the screen being oblique to the input face. Each of the waveguides includes a transparent core bound by a cladding layer having a lower index of refraction for effecting internal reflection of image light transmitted into the input face to project an image on the screen, with each of the cladding layers including a cladding cap integrally joined thereto at the waveguide second ends. Each of the cores is beveled at the waveguide second end so that the cladding cap is viewable through the transparent core. Each of the cladding caps is black for absorbing external ambient light incident upon the screen for improving contrast of the image projected internally on the screen.

A gel-based visual immunoassay for non-instrumental detection of chloramphenicol in food samples.

PubMed

Yuan, Meng; Sheng, Wei; Zhang, Yan; Wang, Junping; Yang, Yijin; Zhang, Shuguang; Goryacheva, Irina Yu; Wang, Shuo

2012-11-02

A gel-based non-instrumental immuno-affinity assay was developed for the rapid screening of chloramphenicol (CAP) in food samples with the limit of detection (LOD) of 1 μg L(-1). The immuno-affinity test column (IATC) consisted of a test layer containing anti-CAP antibody coupled gel, and a control layer with anti-HRP antibody coupled gel. Based on the direct competitive immuno-reaction and the horseradish peroxidase enzymatic reaction, the test results could be evaluated visually. Basically, blue color development represented the negative results, while the absence of color development represented the positive results. In this study, CAP spiked samples of raw milk, pasteurized milk, UHT milk, skimmed milk powder, acacia honey, date honey, fish and shrimp were tested. Little or none sample pretreatment was required for this assay. The whole procedure was completed within 10min. In conclusion, the gel-based immuno-affinity test is a simple, rapid, and promising on-site screening method for CAP residues in food samples, with no instrumental requirement. Copyright © 2012 Elsevier B.V. All rights reserved.

Depositing spacing layers on magnetic film with liquid phase epitaxy

NASA Technical Reports Server (NTRS)

Moody, J. W.; Shaw, R. W.; Sanfort, R. M.

1975-01-01

Liquid phase epitaxy spacing layer is compatible with systems which are hard-bubble proofed by use of second magnetic garnet film as capping layer. Composite is superior in that: circuit fabrication time is reduced; adherence is superior; visibility is better; and, good match of thermal expansion coefficients is provided.

Response of marine benthic fauna to thin-layer capping with activated carbon in a large-scale field experiment in the Grenland fjords, Norway.

PubMed

Samuelsson, Göran S; Raymond, Caroline; Agrenius, Stefan; Schaanning, Morten; Cornelissen, Gerard; Gunnarsson, Jonas S

2017-06-01

A field experiment with thin-layer capping was conducted in the Grenland fjords, Norway, for remediation in situ of mercury and dioxin-contaminated sediments. Experimental fields at 30 and 95 m depth were capped with (i) powdered activated carbon (AC) mixed with clay (AC+cla`y), (ii) clay, and (iii) crushed limestone. Ecological effects on the benthic community and species-feeding guilds were studied 1 and 14 months after capping, and a total of 158 species were included in the analyses. The results show that clay and limestone had only minor effects on the benthic community, while AC+clay caused severe perturbations. AC+clay reduced the abundance, biomass, and number of species by up to 90% at both 30 and 95 m depth, and few indications of recovery were found during the period of this investigation. The negative effects of AC+clay were observed on a wide range of species with different feeding strategies, although the suspension feeding brittle star Amphiura filiformis was particularly affected. Even though activated carbon is effective in reducing sediment-to-water fluxes of dioxins and other organic pollutants, this study shows that capping with powdered AC can lead to substantial disturbances to the benthic community.

Bioturbation delays attenuation of DDT by clean sediment cap but promotes sequestration by thin-layered activated carbon.

PubMed

Lin, Diana; Cho, Yeo-Myoung; Werner, David; Luthy, Richard G

2014-01-21

The effects of bioturbation on the performance of attenuation by sediment deposition and activated carbon to reduce risks from DDT-contaminated sediment were assessed for DDT sediment-water flux, biouptake, and passive sampler (PE) uptake in microcosm experiments with a freshwater worm, Lumbriculus variegatus. A thin-layer of clean sediment (0.5 cm) did not reduce the DDT flux when bioturbation was present, while a thin (0.3 cm) AC cap was still capable of reducing the DDT flux by 94%. Bioturbation promoted AC sequestration by reducing the 28-day DDT biouptake (66%) and DDT uptake into PE (>99%) compared to controls. Bioturbation further promoted AC-sediment contact by mixing AC particles into underlying sediment layers, reducing PE uptake (55%) in sediment compared to the AC cap without bioturbation. To account for the observed effects from bioturbation, a mass transfer model together with a biodynamic model were developed to simulate DDT flux and biouptake, respectively, and models confirmed experimental results. Both experimental measurements and modeling predictions imply that thin-layer activated carbon placement on sediment is effective in reducing the risks from contaminated sediments in the presence of bioturbation, while natural attenuation process by clean sediment deposition may be delayed by bioturbation.

An analytical model of capped turbulent oscillatory bottom boundary layers

NASA Astrophysics Data System (ADS)

Shimizu, Kenji

2010-03-01

An analytical model of capped turbulent oscillatory bottom boundary layers (BBLs) is proposed using eddy viscosity of a quadratic form. The common definition of friction velocity based on maximum bottom shear stress is found unsatisfactory for BBLs under rotating flows, and a possible extension based on turbulent kinetic energy balance is proposed. The model solutions show that the flow may slip at the top of the boundary layer due to capping by the water surface or stratification, reducing the bottom shear stress, and that the Earth's rotation induces current and bottom shear stress components perpendicular to the interior flow with a phase lag (or lead). Comparisons with field and numerical experiments indicate that the model predicts the essential characteristics of the velocity profiles, although the agreement is rather qualitative due to assumptions of quadratic eddy viscosity with time-independent friction velocity and a well-mixed boundary layer. On the other hand, the predicted linear friction coefficients, phase lead, and veering angle at the bottom agreed with available data with an error of 3%-10%, 5°-10°, and 5°-10°, respectively. As an application of the model, the friction coefficients are used to calculate e-folding decay distances of progressive internal waves with a semidiurnal frequency.

Effect of metallic capping layers on the superconductivity in FeSe thin films.

NASA Astrophysics Data System (ADS)

Shibayev, Pavel; Salehi, Maryam; Moon, Jisoo; Oh, Seongshik; Oh Lab Team

In the past few years, there has been an increased interest in understanding the superconducting behavior of iron selenide (FeSe). Past efforts of others aimed at growing FeSe thin films yielded some success in reaching a Tc of 40K, but at present there is a stark lack of consensus among groups working on this problem. We set a goal of growing FeSe on insulating SrTiO3 (STO) substrates by optimizing both the growth temperature and the protection layer. In our quest to achieve this, we concentrate on keeping track of each compound's structural evolution with temperature via RHEED, an aspect often overlooked in papers describing FeSe growth, thus presenting a unique perspective to tackling this multifaceted challenge. Our group has grown 1, 3, and 30 unit-cell thick FeSe on STO using a state-of-the-art molecular beam epitaxy (MBE) system in our lab. Crucially, we expect to search for superconductivity in FeSe capped by unprecedented metallic protection layers. In addition, the FeSe/STO heterostructures with FeTe protection layers will be grown to enable comparison of existing transport data and scanning tunneling spectra (STS) to data involving our own novel cappings. Support: NSF EFRI Scholars program (1542798), EPiQS Initiative (GBMF4418).

Buffer architecture for biaxially textured structures and method of fabricating same

DOEpatents

Norton, David P.; Park, Chan; Goyal, Amit

2004-04-06

The invention relates to an article with an improved buffer layer architecture comprising a substrate having a metal surface, and an epitaxial buffer layer on the surface of the substrate. The epitaxial buffer layer comprises at least one of the group consisting of ZrO.sub.2, HfO.sub.2, and compounds having at least one of Ca and a rare earth element stabilizing cubic phases of ZrO.sub.2 and/or HfO.sub.2. The article can also include a superconducting layer deposited on the epitaxial buffer layer. The article can also include an epitaxial capping layer between the epitaxial buffer layer and the superconducting layer. A method for preparing an epitaxial article comprises providing a substrate with a metal surface, depositing on the metal surface an epitaxial buffer layer comprising at least one material selected from the group consisting of ZrO.sub.2, HfO.sub.2, and compounds having at least one of Ca and a rare earth element stabilizing cubic phases of at least one of ZrO.sub.2 and HfO.sub.2. The epitaxial layer depositing step occurs in a vacuum with a background pressure of no more than 1.times.10.sup.-5 Torr. The method can further comprise depositing a superconducting layer on the epitaxial layer, and depositing an epitaxial capping layer between the epitaxial buffer layer and the superconducting layer.

Surfactant-Mediated Growth of Ge/Si(001) Interface Studied by XPD

NASA Astrophysics Data System (ADS)

Gunnella, R.; Castrucci, P.; Pinto, N.; Cucculelli, P.; Davoli, I.; Sébilleau, D.; de Crescenzi, M.

The influence of Sb as a surfactant on the formation of Si/Ge interface is studied by means of XPD (X-ray photoelectron diffraction) and AED (Auger electron diffraction) from Ge and Si core levels. The technique employed is particularly suitable for checking the film tetragonal distortion, the growth morphology and the sharpness of the interface. We found a layer by layer growth mode for 3 ML of Ge on Si(001) and related values of strain of the film close to the value predicted by the elastic theory which enforces the use of such a surfactant to obtain high quality and sharp heterostructures. In addition, studying the influence of 3 ML of the Si cap layer on the 3 ML Ge, we obtain no indication of Ge segregation into the Si cap layer. Finally, evidences of quality degradation after high temperature (T > 600°C) annealing are shown.

Indirect excitation of ultrafast demagnetization

DOE PAGES

Vodungbo, Boris; Tudu, Bahrati; Perron, Jonathan; ...

2016-01-06

Does the excitation of ultrafast magnetization require direct interaction between the photons of the optical pump pulse and the magnetic layer? Here, we demonstrate unambiguously that this is not the case. For this we have studied the magnetization dynamics of a ferromagnetic cobalt/palladium multilayer capped by an IR-opaque aluminum layer. Upon excitation with an intense femtosecond-short IR laser pulse, the film exhibits the classical ultrafast demagnetization phenomenon although only a negligible number of IR photons penetrate the aluminum layer. In comparison with an uncapped cobalt/palladium reference film, the initial demagnetization of the capped film occurs with a delayed onset andmore » at a slower rate. Both observations are qualitatively in line with energy transport from the aluminum layer into the underlying magnetic film by the excited, hot electrons of the aluminum film. As a result, our data thus confirm recent theoretical predictions.« less

Lithium Recovery from Aqueous Resources and Batteries: A Brief Review

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Ling; Deshmane, Vishwanath G.; Paranthaman, M. Parans

The demand for lithium is expected to increase drastically in the near future due to the increased usage of rechargeable lithium-ion batteries (LIB) in electric vehicles, smartphones and other portable electronics. To alleviate the potential risk of undersupply, lithium can be extracted from raw sources consisting of minerals and brines or from recycled batteries and glasses. Aqueous lithium mining from naturally occurring brines and salt deposits is advantageous compared to extraction from minerals, since it may be more environmentally friendly and cost-effective. In this article, we briefly discuss the adsorptive behaviour, synthetic methodology and prospects or challenges of major sorbentsmore » including spinel lithium manganese oxide (Li-Mn-O or LMO), spinel lithium titanium oxide (Li-Ti-O or LTO) and lithium aluminium layered double hydroxide chloride (LiCl·2Al(OH)3). Membrane approaches and lithium recovery from end-of-life LIB will also be briefly discussed.« less

Lithium Recovery from Aqueous Resources and Batteries: A Brief Review

DOE PAGES

Li, Ling; Deshmane, Vishwanath G.; Paranthaman, M. Parans; ...

2018-04-01

The demand for lithium is expected to increase drastically in the near future due to the increased usage of rechargeable lithium-ion batteries (LIB) in electric vehicles, smartphones and other portable electronics. To alleviate the potential risk of undersupply, lithium can be extracted from raw sources consisting of minerals and brines or from recycled batteries and glasses. Aqueous lithium mining from naturally occurring brines and salt deposits is advantageous compared to extraction from minerals, since it may be more environmentally friendly and cost-effective. In this article, we briefly discuss the adsorptive behaviour, synthetic methodology and prospects or challenges of major sorbentsmore » including spinel lithium manganese oxide (Li-Mn-O or LMO), spinel lithium titanium oxide (Li-Ti-O or LTO) and lithium aluminium layered double hydroxide chloride (LiCl·2Al(OH)3). Membrane approaches and lithium recovery from end-of-life LIB will also be briefly discussed.« less

Genetic ablation of root cap cells in Arabidopsis

NASA Technical Reports Server (NTRS)

Tsugeki, R.; Fedoroff, N. V.

1999-01-01

The root cap is increasingly appreciated as a complex and dynamic plant organ. Root caps sense and transmit environmental signals, synthesize and secrete small molecules and macromolecules, and in some species shed metabolically active cells. However, it is not known whether root caps are essential for normal shoot and root development. We report the identification of a root cap-specific promoter and describe its use to genetically ablate root caps by directing root cap-specific expression of a diphtheria toxin A-chain gene. Transgenic toxin-expressing plants are viable and have normal aerial parts but agravitropic roots, implying loss of root cap function. Several cell layers are missing from the transgenic root caps, and the remaining cells are abnormal. Although the radial organization of the roots is normal in toxin-expressing plants, the root tips have fewer cytoplasmically dense cells than do wild-type root tips, suggesting that root meristematic activity is lower in transgenic than in wild-type plants. The roots of transgenic plants have more lateral roots and these are, in turn, more highly branched than those of wild-type plants. Thus, root cap ablation alters root architecture both by inhibiting root meristematic activity and by stimulating lateral root initiation. These observations imply that the root caps contain essential components of the signaling system that determines root architecture.

Self Concept of Adolescent Sexual Abuse Victims.

ERIC Educational Resources Information Center

Orr, Donald P.; Downes, Maureen C.

1985-01-01

To assess the self-concept and psychological profile associated with sexual abuse, 20 young female victims evaluated in a sexual abuse clinic completed the Offer Self-Image Questionnaire. (Author/LMO)

EUVL mask patterning with blanks from commercial suppliers

NASA Astrophysics Data System (ADS)

Yan, Pei-Yang; Zhang, Guojing; Nagpal, Rajesh; Shu, Emily Y.; Li, Chaoyang; Qu, Ping; Chen, Frederick T.

2004-12-01

Extreme Ultraviolet Lithography (EUVL) reflective mask blank development includes low thermal expansion material fabrication, mask substrate finishing, reflective multi-layer (ML) and capping layer deposition, buffer (optional)/absorber stack deposition, EUV specific metrology, and ML defect inspection. In the past, we have obtained blanks deposited with various layer stacks from several vendors. Some of them are not commercial suppliers. As a result, the blank and patterned mask qualities are difficult to maintain and improve. In this paper we will present the evaluation results of the EUVL mask pattering processes with the complete EUVL mask blanks supplied by the commercial blank supplier. The EUVL mask blanks used in this study consist of either quartz or ULE substrates which is a type of low thermal expansion material (LTEM), 40 pairs of molybdenum/silicon (Mo/Si) ML layer, thin ruthenium (Ru) capping layer, tantalum boron nitride (TaBN) absorber, and chrome (Cr) backside coating. No buffer layer is used. Our study includes the EUVL mask blank characterization, patterned EUVL mask characterization, and the final patterned EUVL mask flatness evaluation.

Probing the energetics of organic–nanoparticle interactions of ethanol on calcite

PubMed Central

Wu, Di; Navrotsky, Alexandra

2015-01-01

Knowing the nature of interactions between small organic molecules and surfaces of nanoparticles (NP) is crucial for fundamental understanding of natural phenomena and engineering processes. Herein, we report direct adsorption enthalpy measurement of ethanol on a series of calcite nanocrystals, with the aim of mimicking organic–NP interactions in various environments. The energetics suggests a spectrum of adsorption events as a function of coverage: strongest initial chemisorption on active sites on fresh calcite surfaces, followed by major chemical binding to form an ethanol monolayer and, subsequently, very weak, near-zero energy, physisorption. These thermochemical observations directly support a structure where the ethanol monolayer is bonded to the calcite surface through its polar hydroxyl group, leaving the hydrophobic ends of the ethanol molecules to interact only weakly with the next layer of adsorbing ethanol and resulting in a spatial gap with low ethanol density between the monolayer and subsequent added ethanol molecules, as predicted by molecular dynamics and density functional calculations. Such an ordered assembly of ethanol on calcite NP is analogous to, although less strongly bonded than, a capping layer of organics intentionally introduced during NP synthesis, and suggests a continuous variation of surface structure depending on molecular chemistry, ranging from largely disordered surface layers to ordered layers that nevertheless are mobile and can rearrange or be displaced by other molecules to strongly bonded immobile organic capping layers. These differences in surface structure will affect chemical reactions, including the further nucleation and growth of nanocrystals on organic ligand-capped surfaces. PMID:25870281

488-1D Ash Basin closure cap help modeling- Microdrain® liner option

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, J. A.

At the request of Area Completion Engineering and in support of the 488-1D Ash Basin closure, the Savannah River National Laboratory (SRNL) performed hydrologic simulations of the revised 488-1D Ash Basin closure cap design using the Hydrologic Evaluation of Landfill Performance (HELP) model. The revised design substitutes a MicroDrain Liner®—60-mil low-density polyethylene geomembrane structurally integrated with 130-mil drainage layer—for the previously planned drainage/barrier system—300-mil geosynthetic drainage layer (GDL), 300-mil geosynthetic clay liner (GCL), and 6-inch common fill soil layer. For a 25-year, 24-hour storm event, HELP model v3.07 was employed to (1) predict the peak maximum daily hydraulic head formore » the geomembrane layer, and (2) ensure that South Carolina Department of Health and Environmental Control (SCDHEC) requirements for the barrier layer (i.e., ≤ 12 inches hydraulic head on top of a barrier having a saturated hydraulic conductivity ≤ 1.0E-05 cm/s) will not be exceeded. A 25-year, 24-hour storm event at the Savannah River Site (SRS) is 6.1 inches rainfall (Weber 1998). HELP model v3.07 results based upon the new planned cap design suggest that the peak maximum daily hydraulic head on the geomembrane barrier layer will be 0.15 inches for a minimum slope equal to 3%, which is two orders of magnitude below the SCDHEC upper limit of 12 inches.« less

488-1D Ash basin closure cap help modeling-Microdrain® liner option

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, J.

At the request of Area Completion Engineering and in support of the 488-1D Ash Basin closure, the Savannah River National Laboratory (SRNL) performed hydrologic simulations of the revised 488-1D Ash Basin closure cap design using the Hydrologic Evaluation of Landfill Performance (HELP) model. The revised design substitutes a MicroDrain Liner®—50-mil linear low-density polyethylene geomembrane structurally integrated with 130-mil drainage layer—for the previously planned drainage/barrier system—300-mil geosynthetic drainage layer (GDL), 300-mil geosynthetic clay liner (GCL), and 6-inch common fill soil layer. For a 25-year, 24-hour storm event, HELP model v3.07 was employed to (1) predict the peak maximum daily hydraulic headmore » for the geomembrane layer, and (2) ensure that South Carolina Department of Health and Environmental Control (SCDHEC) requirements for the barrier layer (i.e., ≤ 12 inches hydraulic head on top of a barrier having a saturated hydraulic conductivity ≤ 1.0E-05 cm/s) will not be exceeded. A 25-year, 24-hour storm event at the Savannah River Site (SRS) is 6.1 inches rainfall (Weber 1998). HELP model v3.07 results based upon the new planned cap design suggest that the peak maximum daily hydraulic head on the geomembrane barrier layer will be 0.179 inches for a minimum slope equal to 3%, which is approximately two orders of magnitude below the SCDHEC upper limit of 12 inches.« less

Characterization, performance modeling, and design of an active capping remediation project in a heavily polluted urban channel.

PubMed

Yin, Ke; Viana, Priscilla; Zhao, Xiuhong; Rockne, Karl

2010-07-15

Collateral Channel is a heavily polluted former navigation slip to the Chicago Sanitary and Ship Canal (Illinois, USA). Characterization of sediment cores taken in the channel show high levels of heavy metals, polycyclic aromatic hydrocarbons (PAHs) and other contaminants in deposited sediment dating back to the 1800's. Of these, PAHs were the contaminants of greatest concern based upon exceedance of sediment contamination criteria (Sigma(16) PAHs up to 1500mg/kg). Benthic animal counts revealed a lack of biodiversity, with relatively low levels of small tubificid oligochaetes (generally <3000/m(2)) in surficial sediments. Comparison of surficial sediment contaminant levels between 1995 and 2005 showed few decreases in contaminant levels, indicating a lack of "natural recovery" processes occurring in the channel. These results led to an analysis of sediment amendments for an active capping demonstration project in the channel using transport models developed in our previous work (Viana et al., 2008). Based on the sediment characterization and modeling results, the active capping design will be focused on organic contaminant sequestration through the use of organoclay. A site-specific difficulty is the substantial rates of gas ebullition from anaerobic organic matter biodegradation in the sediments, particularly in the summer months. These gases can open advective channels that may result in substantial pollution release and compromise cap effectiveness, and thus the capping scenario must control for such releases. The active capping layer will underlay a sloped sand layer and a high permeability gas venting system to allow biogenically-produced gas migration to shoreline collectors through an innovative support grid. The cap will include an overlaying wetland to remove nutrients from the adjoining Chicago River and provide a public recreational space. Copyright 2010 Elsevier B.V. All rights reserved.

Contributions of IKZF1, DDC, CDKN2A, CEBPE, and LMO1 Gene Polymorphisms to Acute Lymphoblastic Leukemia in a Yemeni Population.

PubMed

Al-Absi, Boshra; Razif, Muhammad F M; Noor, Suzita M; Saif-Ali, Riyadh; Aqlan, Mohammed; Salem, Sameer D; Ahmed, Radwan H; Muniandy, Sekaran

2017-10-01

Genome-wide and candidate gene association studies have previously revealed links between a predisposition to acute lymphoblastic leukemia (ALL) and genetic polymorphisms in the following genes: IKZF1 (7p12.2; ID: 10320), DDC (7p12.2; ID: 1644), CDKN2A (9p21.3; ID: 1029), CEBPE (14q11.2; ID: 1053), and LMO1 (11p15; ID: 4004). In this study, we aimed to conduct an investigation into the possible association between polymorphisms in these genes and ALL within a sample of Yemeni children of Arab-Asian descent. Seven single-nucleotide polymorphisms (SNPs) in IKZF1, three SNPs in DDC, two SNPs in CDKN2A, two SNPs in CEBPE, and three SNPs in LMO1 were genotyped in 289 Yemeni children (136 cases and 153 controls), using the nanofluidic Dynamic Array (Fluidigm 192.24 Dynamic Array). Logistic regression analyses were used to estimate ALL risk, and the strength of association was expressed as odds ratios with 95% confidence intervals. We found that the IKZF1 SNP rs10235796 C allele (p = 0.002), the IKZF1 rs6964969 A>G polymorphism (p = 0.048, GG vs. AA), the CDKN2A rs3731246 G>C polymorphism (p = 0.047, GC+CC vs. GG), and the CDKN2A SNP rs3731246 C allele (p = 0.007) were significantly associated with ALL in Yemenis of Arab-Asian descent. In addition, a borderline association was found between IKZF1 rs4132601 T>G variant and ALL risk. No associations were found between the IKZF1 SNPs (rs11978267; rs7789635), DDC SNPs (rs3779084; rs880028; rs7809758), CDKN2A SNP (rs3731217), the CEBPE SNPs (rs2239633; rs12434881) and LMO1 SNPs (rs442264; rs3794012; rs4237770) with ALL in Yemeni children. The IKZF1 SNPs, rs10235796 and rs6964969, and the CDKN2A SNP rs3731246 (previously unreported) could serve as risk markers for ALL susceptibility in Yemeni children.

Upstream Passage, Spawning, and Stock Identification of Fall Chinook in the Snake River, 1992 and 1993 : Final Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Blankenship, H. Lee; Mendel, Glen W.

This final report of the 3-year study summarizes activities and results for 1993. Study objectives were to: (1) determine the source of losses (or accounting errors) for adult chinook salmon between Ice Harbor Dam (IHR) and Lower Granite Dam (LGR), and upstream of LGR in the Snake River; (2) identify spawning locations upstream of LGR for calibration of aerial redd surveys, redd habitat mapping, carcass recovery for genetic stock profile analysis, and correction of estimated adult/redd ratios; and (3) estimate passage and migration times at Snake River. 200 fall chinook salmon were radio tagged and tracked with aerial, fixed-site, andmore » ground mobile tracking. Fish were released upstream of IHR at Charbonneau Park (CHAR). 190 of the fish were tracked or relocated away from CHAR. 59 fish descended to below IHR without crossing Lower Monumental Dam (LMO). Another 128 salmon passed upstream of LMO without falling back at IHR. Only 80 salmon passed Little Goose Dam (LGO) without falling back at a downstream dam; 66 of these fish passed LGR. Many fish that fell back reascended the dams. A total of 72 salmon released at CHAR passed upstream of LGR, including fish that had fallen back and reascended a dam. Over 80 percent of the salmon that entered Lyons Ferry Hatchery each year had reached LGO before descending to the hatchery. Extensive wandering was documented between LMO and upstream of LGR before salmon entered Lyons Ferry Hatchery or the Tucannon River. In 1993, 41 salmon were found to be of hatchery origin when recovered. These fish entered Lyons Ferry Hatchery with similar movements to unmarked salmon. Each year a few salmon have remained near the hatchery without entering, which suggests the hatchery may have inadequate attraction flows. Fall chinook passed lower Snake River dams in 2-5 days each on average. Median travel times through LMO and LGO were 1.0-1.3 days each, which was slower than for spring chinook or steelhead in 1993. 5 refs., 21 figs., 20 tabs.« less

Dichotomy Boundary at Aeolis Mensae, Mars: Fretted Terrain Developed in a Sedimentary Deposit

NASA Astrophysics Data System (ADS)

Irwin, R. P., III; Watters, T. R.; Howard, A. D.; Maxwell, T. A.; Craddock, R. A.

2003-03-01

Fretted terrain in Aeolis Mensae, Mars, developed in a sedimentary deposit. A thick, massive unit with a capping layer or duricrust overlies a more durable layered sequence. Wind, collapse, and minor fluvial activity contributed to degradation.

ACCURATE: Influence of Cloud Layers and Aerosol on Infrared Laser Occultation Signals for Sensing of Greenhouse Gases

NASA Astrophysics Data System (ADS)

Proschek, V.; Schweitzer, S.; Emde, C.; Ladstädter, F.; Fritzer, J.; Kirchengast, G.

2009-04-01

ACCURATE (Atmospheric Climate and Chemistry in the UTLS Region And climate Trends Explorer), a new climate satellite concept, enables simultaneous measurement of profiles of greenhouse gases, isotopes, wind and thermodynamic variables from Low Earth Orbit (LEO) satellites. The measurement principle applied is a combination of the novel LEO-LEO infrared laser occultation (LIO) technique and the well-studied but not yet flown LEO-LEO microwave occultation (LMO) technique. As intrinsic to the space-borne occultation technique, the measurements are evenly distributed around the world, have high vertical resolution and high accuracy and are stable over long time periods. The LIO uses near-monochromatic signals in the short-wave infrared range (~2-2.5 m in the case of ACCURATE) which are absorbed by various trace species in the Earth's atmosphere. From signal transmission measurements, profiles of the concentration of the absorbing species can be derived given that temperature and pressure are accurately known from LMO. The current ACCURATE mission design is arranged for the measurement of six greenhouse gases (H2O, CO2, CH4, N2O, O3, CO) and four isotopes (13CO2, C18OO, HDO, H218O) with focus on the upper troposphere/lower stratosphere region (UTLS, 5-35 km). Wind speed in line-of-sight can be derived from a line-symmetric transmission difference which is caused by wind-induced Doppler shift. By-products are information on cloud layering, aerosol extinction and scintillation strength. This contribution presents an overview on the ACCURATE mission design and the expected accuracy of retrieved atmospheric variables and further focuses on the influence of clouds and aerosols on propagating LIO signals. Special emphasis will be given to sub-visible cirrus clouds which are semi-transparent to infrared signals. A simple frequency dependent cloud extinction parametrization was included into the occultation propagation software EGOPS and evaluated against results of the advanced radiative transfer model libRadtran. Use of this parametrization also allows to separate the disturbance by clouds from other atmospheric influences on signal transmission. The influence of aerosols was investigated by means of an extinction model developed on the basis of SAGE (Stratospheric Aerosol and Gas Experiment) measurements. The effects of different cases from background to volcanic aerosol levels are presented.

Nano-oxide-layer insertion and specular effects in spin valves: Experiment and theory

NASA Astrophysics Data System (ADS)

Wang, L.; Qiu, J. J.; McMahon, W. J.; Li, K. B.; Wu, Y. H.

2004-06-01

We report a systematic study of NOL (nano-oxide-layer) insertion and specular effects on the giant magnetoresistance (GMR) of single, synthetic, and dual spin valves, using a semiclassical Boltzmann theory. It is confirmed that the GMR ratio is enhanced by NOL insertion inside the pinned layer or after the free layer. The enhancements are primarily due to the contribution of the majority carriers. The NOL insertions inside the inactive layers of spin valves such as the seed, under, and capping layers reduce the GMR ratio. Though introducing a NOL before or after the Cu spacer would, in principle, significantly suppress the GMR ratio due to the blocking effect or the average effect of different spin channels, large positive or negative (inverse) GMR is found by assuming spin-dependent NOL specular reflections. We have also demonstrated that specular reflection, even beyond a capping layer, may result in reduction of GMR. Upon appropriate NOL insertion, the amplitude of curve of GMR versus thickness of individual layer of spin valves may be generally enhanced, but the shape may change, depending on whether the distance of the NOL to the layer is small or large (distance effect). Finally, it is found that most results obtained for the single realistic spin valves are applicable to synthetic and dual spin valves.

Studies of morphological instability and defect formation in heteroepitaxial Si(1-x)Ge(x) thin films via controlled annealing experiments

NASA Astrophysics Data System (ADS)

Ozkan, Cengiz Sinan

Strained layer semiconductor structures provide possibilities for novel electronic devices. When a semiconductor layer is deposited epitaxially onto a single crystal substrate with the same structure but a slightly different lattice parameter, the semiconductor layer grows commensurately with a misfit strain that can be accommodated elastically below a critical thickness. When the critical thickness is exceeded, the elastic strain energy builds up to a point where it becomes energetically favorable to form misfit dislocations. In addition, in the absence of a capping layer, Sisb{1-x}Gesb{x} films exhibit surface roughening via surface diffusion under the effect of a compressive stress which is caused by a lattice mismatch. Surface roughening takes place in the form of ridges aligned along {<}100{>} or {<}110{>} directions depending on the film thickness and the rate of strain relief. Recent work has shown that surface roughening makes a very significant contribution to strain relaxation in heteroepitaxial thin films. At sharp valley regions on the surface, amplified local stresses can cause further defect nucleation and propagation, such as stacking faults and 90sp° dislocations. In addition, capping layers with suitable thickness will surpress surface roughening and keep most of the strain in the film. We study surface roughening and defect formation by conducting controlled annealing experiments on initially flat and defect free films grown by LPCVD in a hydrogen ambient. We study films with both subcritical and supercritical thicknesses. In addition, we compare the relaxation behaviour of capped and uncapped films where surface roughening was inhibited in films with a capping layer. TEM and AFM studies were conducted to study the morphology and microstructure of these films. X-ray diffraction measurements were made to determine the amount of strain relaxation in these films. Further studies of surface roughening on heteroepitaxial films under a positive biaxial stress have shown that, morphological evolution occurs regardless of the sign of stress in the film. Finally, we have studied surface roughening processes in real time by conducting in-situ TEM experiments. We have observed that the kinetics of roughening depend strongly on the annealing ambient.

InAs/GaAs quantum-dot intermixing: comparison of various dielectric encapsulants

NASA Astrophysics Data System (ADS)

Alhashim, Hala H.; Khan, Mohammed Zahed Mustafa; Majid, Mohammed A.; Ng, Tien K.; Ooi, Boon S.

2015-10-01

We report on the impurity-free vacancy-disordering effect in InAs/GaAs quantum-dot (QD) laser structure based on seven dielectric capping layers. Compared to the typical SiO2 and Si3N4 films, HfO2 and SrTiO3 dielectric layers showed superior enhancement and suppression of intermixing up to 725°C, respectively. A QD peak ground-state differential blue shift of >175 nm (>148 meV) is obtained for HfO2 capped sample. Likewise, investigation of TiO2, Al2O3, and ZnO capping films showed unusual characteristics, such as intermixing-control caps at low annealing temperature (650°C) and interdiffusion-promoting caps at high temperatures (≥675°C). We qualitatively compared the degree of intermixing induced by these films by extracting the rate of intermixing and the temperature for ground-state and excited-state convergences. Based on our systematic characterization, we established reference intermixing processes based on seven different dielectric encapsulation materials. The tailored wavelength emission of ˜1060-1200 nm at room temperature and improved optical quality exhibited from intermixed QDs would serve as key materials for eventual realization of low-cost, compact, and agile lasers. Applications include solid-state laser pumping, optical communications, gas sensing, biomedical imaging, green-yellow-orange coherent light generation, as well as addressing photonic integration via area-selective, and postgrowth bandgap engineering.

Two-dimensional electron gases in MgZnO/ZnO and ZnO/MgZnO/ZnO heterostructures grown by dual ion beam sputtering

NASA Astrophysics Data System (ADS)

Singh, Rohit; Arif Khan, Md; Sharma, Pankaj; Than Htay, Myo; Kranti, Abhinav; Mukherjee, Shaibal

2018-04-01

This work reports on the formation of high-density (~1013-1014 cm-2) two-dimensional electron gas (2DEG) in ZnO-based heterostructures, grown by a dual ion beam sputtering system. We probe 2DEG in bilayer MgZnO/ZnO and capped ZnO/MgZnO/ZnO heterostructures utilizing MgZnO barrier layers with varying thickness and Mg content. The effect of the ZnO cap layer thickness on the ZnO/MgZnO/ZnO heterostructure is also studied. Hall measurements demonstrate that the addition of a 5 nm ZnO cap layer results in an enhancement of the 2DEG density by about 1.5 times compared to 1.11 × 1014 cm-2 for the uncapped bilayer heterostructure with the same 30 nm barrier thickness and 30 at.% Mg composition in the barrier layer. From the low-temperature Hall measurement, the sheet carrier concentration and mobility are both found to be independent of the temperature. The capacitance-voltage measurement suggests a carrier density of ~1020 cm-3, confined in 2DEG at the MgZnO/ZnO heterointerface. The results presented are significant for the optimization of 2DEG for the eventual realization of cost-effective and large-area MgZnO/ZnO-based high-electron-mobility transistors.

LES on Plume Dispersion in the Convective Boundary Layer Capped by a Temperature Inversion

NASA Astrophysics Data System (ADS)

Nakayama, Hiromasa; Tamura, Tetsuro; Abe, Satoshi

Large-eddy simulation (LES) is applied to the problem of plume dispersion in the spatially-developing convective boundary layer (CBL) capped by a temperature inversion. In order to generate inflow turbulence with buoyant forcing, we first, simulate the neutral boundary layer flow (NBL) in the driver region using Lund's method. At the same time, the temperature profile possessing the inversion part is imposed at the entrance of the driver region and the temperature field is calculated as a passive scalar. Next, the buoyancy effect is introduced into the flow field in the main region. We evaluate the applicability of the LES model for atmospheric dispersion in the CBL flow and compare the characteristics of plume dispersion in the CBL flow with those in the neutral boundary layer. The Richardson number based on the temperature increment across the inversion obtained by the present LES model is 22.4 and the capping effect of the temperature inversion can be captured qualitatively in the upper portion of the CBL. Characteristics of flow and temperature fields in the main portion of CBL flow are similar to those of previous experiments[1],[2] and observations[3]. Concerning dispersion behavior, we also find that mean concentrations decrease immediately above the inversion height and the peak values of r.m.s concentrations are located near the inversion height at larger distances from the point source.

Screening of the two-component-system histidine kinases of Listeria monocytogenes EGD-e. LiaS is needed for growth under heat, acid, alkali, osmotic, ethanol and oxidative stresses.

PubMed

Pöntinen, Anna; Lindström, Miia; Skurnik, Mikael; Korkeala, Hannu

2017-08-01

To study the role of each two-component system (TCS) histidine kinase (HK) in stress tolerance of Listeria monocytogenes EGD-e, we monitored the growth of individual HK deletion mutant strains under heat (42.5 °C), acid (pH 5.6), alkali (pH 9.4), osmotic (6% NaCl), ethanol (3.5 vol%), and oxidative (5 mM H 2 O 2 ) stresses. The growth of ΔliaS (Δlmo1021) strain was impaired under each stress, with the most notable decrease under heat and osmotic stresses. The ΔvirS (Δlmo1741) strain showed nearly completely restricted growth at high temperature and impaired growth in ethanol. The growth of ΔagrC (Δlmo0050) strain was impaired under osmotic stress and slightly under oxidative stress. We successfully complemented the HK mutations using a novel allelic exchange based approach. This approach avoided the copy-number problems associated with in trans complementation from a plasmid. The mutant phenotypes were restored to the wild-type level in the complemented strains. This study reveals novel knowledge on the HKs needed for growth of L. monocytogenes EGD-e under abovementioned stress conditions, with LiaS playing multiple roles in stress tolerance of L. monocytogenes EGD-e. Copyright © 2017 Elsevier Ltd. All rights reserved.

Detection methods for biotech cotton MON 15985 and MON 88913 by PCR.

PubMed

Lee, Seong-Hun; Kim, Jin-Kug; Yi, Bu-Young

2007-05-02

Plants derived through agricultural biotechnology, or genetically modified organisms (GMOs), may affect human health and ecological environment. A living GMO is also called a living modified organism (LMO). Biotech cotton is a GMO in food or feed and also an LMO in the environment. Recently, two varieties of biotech cotton, MON 15985 and MON 88913, were developed by Monsanto Co. The detection method is an essential element for the GMO labeling system or LMO management of biotech plants. In this paper, two primer pairs and probes were designed for specific amplification of 116 and 120 bp PCR products from MON 15985 and MON 88913, respectively, with no amplification from any other biotech cotton. Limits of detection of the qualitative method were all 0.05% for MON 15985 and MON 88913. The quantitative method was developed using a TaqMan real-time PCR. A synthetic plasmid, as a reference molecule, was constructed from a taxon-specific DNA sequence of cotton and two construct-specific DNA sequences of MON 15985 and MON 88913. The quantitative method was validated using six samples that contained levels of biotech cotton mixed with conventional cotton ranging from 0.1 to 10.0%. As a result, the biases from the true value and the relative deviations were all within the range of +/-20%. Limits of quantitation of the quantitative method were all 0.1%. Consequently, it is reported that the proposed detection methods were applicable for qualitative and quantitative analyses for biotech cotton MON 15985 and MON 88913.

Compositional effects on the formation of a calcium phosphate layer and the response of osteoblast-like cells on polymer-bioactive glass composites.

PubMed

Lu, Helen H; Tang, Amy; Oh, Seong Cheol; Spalazzi, Jeffrey P; Dionisio, Kathie

2005-11-01

Biodegradable polymer-ceramic composites are attractive systems for bone tissue engineering applications. These composites have the combined advantages of the component phases, as well as the inherent ease in optimization where desired material properties can be tailored in a well-controlled manner. This study focuses on the optimization of a polylactide-co-glycolide (PLAGA) and 45S5 bioactive glass (BG) composite for bone tissue engineering. The first objective is to examine the effects of composition or overall BG content on the formation of a Ca-P layer on the PLAGA-BG composite. It is expected that with increasing BG content (0%, 10%, 25%, 50% by weight), the required incubation time in a simulated body fluid (SBF) for the composite to form a detectable surface Ca-P layer will decrease. Both the kinetics and the chemistry will be determined using SEM+EDAX, FTIR, and mu-CT methods. Solution phosphorous and calcium concentrations will also be measured. The second objective of the study is to determine the effects of BG content on the maturation of osteoblast-like cells on the PLAGA-BG composite. It is hypothesized that mineralization will increase with increasing BG content, and the composite will support the proliferation and differentiation of osteoblasts. Specifically, cell proliferation, alkaline phosphatase activity and mineralization will be monitored as a function of BG content (0%, 10%, 50% by weight) and culturing time. It was found that the kinetics of Ca-P layer formation and the resulting Ca-P chemistry were dependent on BG content. The response of human osteoblast-like cells to the PLAGA-BG composite was also a function of BG content. The 10% and 25% BG composite supported greater osteoblast growth and differentiation compared to the 50% BG group. The results of this study suggest that there is a threshold BG content which is optimal for osteoblast growth, and the interactions between PLAGA and BG may modulate the kinetics of Ca-P formation and the overall cellular response.

More South Polar "Swiss Cheese"

NASA Image and Video Library

2000-04-24

This image is illuminated by sunlight from the upper left. Some of the surface of the residual south polar cap has a pattern that resembles that of sliced, swiss cheese. Shown here at the very start of southern spring is a frost-covered surface in which there are two layers evident--a brighter upper layer into which are set swiss cheese-like holes, and a darker, lower layer that lies beneath the "swiss cheese" pattern. Nothing like this exists anywhere on Mars except within the south polar cap. This is a Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image acquired on August 2, 1999. It is located near 84.8°S, 71.8°W, and covers an area 3 km across and about 6.1 km long (1.9 by 3.8 miles). http://photojournal.jpl.nasa.gov/catalog/PIA02368

The Subsurface Ice Probe (SIPR): A Low-Power Thermal Probe for the Martian Polar Layered Deposits

NASA Technical Reports Server (NTRS)

Cardell, G.; Hecht, M. H.; Carsey, F. D.; Engelhardt, H.; Fisher, D.; Terrell, C.; Thompson, J.

2004-01-01

The distinctive layering visible in images from Mars Global Surveyor of the Martian polar caps, and particularly in the north polar cap, indicates that the stratigraphy of these polar layered deposits may hold a record of Martian climate history covering millions of years. On Earth, ice sheets are cored to retrieve a pristine record of the physical and chemical properties of the ice at depth, and then studied in exacting detail in the laboratory. On the Martian north polar cap, coring is probably not a practical method for implementation in an autonomous lander. As an alternative, thermal probes that drill by melting into the ice are feasible for autonomous operation, and are capable of reasonable approximations to the scientific investigations performed on terrestrial cores, while removing meltwater to the surface for analysis. The Subsurface Ice Probe (SIPR) is such a probe under development at JPL. To explore the dominant climate cycles, it is postulated that tens of meters of depth should be profiled, as this corresponds to the vertical separation of the major layers visible in the MOC images [1]. Optical and spectroscopic analysis of the layers, presumably demarcated by embedded dust and possibly by changes in the ice properties, would contribute to the construction of a chronology. Meltwater analysis may be used to determine the soluble chemistry of the embedded dust, and to monitor gradients of atmospheric gases, particularly hydrogen and oxygen, and isotopic variations that reflect atmospheric conditions at the time the layer was deposited. Thermal measurements can be used to determine the geothermal gradient and the bulk mechanical properties of the ice.

High density nonmagnetic cobalt in thin films

NASA Astrophysics Data System (ADS)

Banu, Nasrin; Singh, Surendra; Basu, Saibal; Roy, Anupam; Movva, Hema C. P.; Lauter, V.; Satpati, B.; Dev, B. N.

2018-05-01

Recently high density (HD) nonmagnetic cobalt has been discovered in a nanoscale cobalt thin film, grown on Si(111) single crystal. This form of cobalt is not only nonmagnetic but also superconducting. These promising results have encouraged further investigations of the growth of the nonmagnetic (NM) phase of cobalt. In the original investigation, the cobalt film had a natural cobalt oxide at the top. We have investigated whether the growth of HD NM cobalt layers in the thin film depends on (i) a capping layer on the cobalt film, (ii) the thickness of the cobalt film and (iii) the nature of the substrate on which the cobalt film is grown. The results of such investigations indicate that for cobalt films capped with a thin gold layer, and for various film thicknesses, HD NM cobalt layers are formed. However, instead of a Si substrate, when the cobalt films are grown on oxide substrates, such as silicon oxide or cobalt oxide, HD NM cobalt layers are not formed. The difference is attributed to the nature—crystalline or amorphous—of the substrate.

Design of bridging layers in geosynthetic-reinforced, column-supported embankments.

DOT National Transportation Integrated Search

2006-01-01

The cost of column-supported embankments depends, in part, on the spacing between the columns and the size of the columns and pile caps. Geosynthetic reinforcement is often employed in bridging layers to enhance load transfer to the columns and to in...

Dynamic XPS measurements of ultrathin polyelectrolyte films containing antibacterial Ag–Cu nanoparticles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taner-Camcı, Merve; Suzer, Sefik, E-mail: suzer@fen.bilkent.edu.tr

Ultrathin films consisting of polyelectrolyte layers prepared by layer-by-layer deposition technique and containing also Ag and Cu nanoparticles exhibit superior antibacterial activity toward Escherichia coli. These films have been investigated with XPS measurements under square wave excitation at two different frequencies, in order to further our understanding about the chemical/physical nature of the nanoparticles. Dubbed as dynamical XPS, such measurements bring out similarities and differences among the surface structures by correlating the binding energy shifts of the corresponding XPS peaks. Accordingly, it is observed that the Cu2p, Ag3d of the metal nanoparticles, and S2p of cysteine, the stabilizer and themore » capping agent, exhibit similar shifts. On the other hand, the C1s, N1s, and S2p peaks of the polyelectrolyte layers shift differently. This finding leads us the claim that the Ag and Cu atoms are in a nanoalloy structure, capped with cystein, as opposed to phase separated entities.« less

Probing the energetics of organic–nanoparticle interactions of ethanol on calcite

DOE PAGES

Wu, Di; Navrotsky, Alexandra

2015-04-13

Knowing the nature of interactions between small organic molecules and surfaces of nanoparticles (NP) is crucial for fundamental understanding of natural phenomena and engineering processes. In this paper, we report direct adsorption enthalpy measurement of ethanol on a series of calcite nanocrystals, with the aim of mimicking organic–NP interactions in various environments. The energetics suggests a spectrum of adsorption events as a function of coverage: strongest initial chemisorption on active sites on fresh calcite surfaces, followed by major chemical binding to form an ethanol monolayer and, subsequently, very weak, near-zero energy, physisorption. Furthermore, these thermochemical observations directly support a structuremore » where the ethanol monolayer is bonded to the calcite surface through its polar hydroxyl group, leaving the hydrophobic ends of the ethanol molecules to interact only weakly with the next layer of adsorbing ethanol and resulting in a spatial gap with low ethanol density between the monolayer and subsequent added ethanol molecules, as predicted by molecular dynamics and density functional calculations. Such an ordered assembly of ethanol on calcite NP is analogous to, although less strongly bonded than, a capping layer of organics intentionally introduced during NP synthesis, and suggests a continuous variation of surface structure depending on molecular chemistry, ranging from largely disordered surface layers to ordered layers that nevertheless are mobile and can rearrange or be displaced by other molecules to strongly bonded immobile organic capping layers. Finally, these differences in surface structure will affect chemical reactions, including the further nucleation and growth of nanocrystals on organic ligand-capped surfaces.« less

Topography of the South Polar Cap and Layered Deposits of Mars: Viking Stereo Grametry at Regional and Local Scales

NASA Technical Reports Server (NTRS)

Schenk, P.; Moore, J.; Stoker, C.

1998-01-01

Layered deposits and residual polar caps on Mars may record the deposition of ice and sediment modulated by periodic climate change. Topographic information relating to layer thicknesses, erosional processes, and formation of dark spirals within these deposits has been sparce or unreliable until the arrival of MOLA in orbit in September 1997. To assist in evaluating these terrains prior to launch and to assess formation and erosion processes in the polar deposits, we have assembled Viking stereo mosaics of the region and have produced the first reliable DEM models of the south polar deposits using automated stereogrammetry tools. Here we report our preliminary topographic results, pending final image pointing updates. The maximum total thickness of the layered deposits in the south polar region is 2.5 km. The thick layered deposits consist of a series of megaterraces. Each terrace is several tens of kilometers wide and is flat or slopes very gently toward the pole. These terraces step downward from a central plateau near the south pole. Terraces are bounded by relatively steep scarps 100-500 meters high that face toward the equator. These scarps correspond to the pattern of dark spirals observed within the residual cap in southern summer, and are interpreted as ice or frost-free surfaces warmed by solar insolation. Several tongue-shaped troughs, with rounded cirquelike heads, are observed near the margins of the deposit. These troughs are 300-600 meters in deep and may be similar to troughs observed in the northern polar deposit.

Preparation and characterization of highly water-soluble magnetic Fe3O4 nanoparticles via surface double-layered self-assembly method of sodium alpha-olefin sulfonate

NASA Astrophysics Data System (ADS)

Li, Honghong; Qin, Li; Feng, Ying; Hu, Lihua; Zhou, Chunhua

2015-06-01

A kind of double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe3O4 magnetic nanoparticles (Fe3O4-AOS-MN) with highly water-solubility was prepared by a wet co-precipitation method with a pH of 4.8. The resulting Fe3O4-AOS-MN could be dispersed into water to form stable magnetic fluid without other treatments. The result of X-ray diffraction (XRD) indicated that the Fe3O4-AOS-MN maintained original crystalline structure and exhibited a diameter of about 7.5 nm. The iron oxide phase of nanoparticles determined by Raman spectroscopy is Fe3O4. Transmission electron microscopy (TEM) analysis confirmed that the Fe3O4-AOS-MN with spherical morphology were uniformly dispersed in water. FT-IR spectroscopy (FT-IR) and thermo-gravimetric analysis (TGA) verified the successful preparation of Fe3O4-AOS-MN capped with double-layered self-assembled AOS. The corresponding capacities of monolayer chemical absorption and the second-layer self-assembly absorption were respectively 4.07 and 14.71 wt% of Fe3O4-MN, which were much lower than those of other surfactants. Vibrating sample magnetometer (VSM) test result showed Fe3O4-AOS-MN possessed superparamagnetic behavior with the saturation magnetization value of about 44.45 emu/g. The blocking temperature TB of Fe3O4-AOS-MN capped with double-layered AOS is 170 K.

Compositional analysis of various layers of upper urinary tract stones by infrared spectroscopy

PubMed Central

He, Zhang; Jing, Zhang; Jing-Cun, Zheng; Chuan-Yi, Hu; Fei, Gao

2017-01-01

The objective of the present study was to determine the composition of various layers of upper urinary stones and assess the mechanisms of stone nucleation and aggregation. A total of 40 integrated urinary tract stones with a diameter of >0.8 cm were removed from the patients. All of the stones were cut in half perpendicularly to the longitudinal axis. Samples were selected from nuclear, internal and external layers of each stone. Fourier transform infrared spectroscopy (FT-IR) was adopted for qualitative and quantitative analysis of all of the fragments and compositional differences among nuclear, internal and external layers of various types of stone were subsequently investigated. A total of 25 cases of calcium oxalate (CaOx) stones and 10 cases of calcium phosphate (CaP) stones were identified to be mixed stones, while 5 uric acid (UA) calculi were pure stones (purity, >95%). In addition, the contents of CaOx and carbapatite (CA.AP) crystals in various layers of the mixed stones were found to be variable. In CaOx stones, the content of CA.AP in nuclear layers was significantly higher than that of the outer layers (32.0 vs. 6.8%; P<0.05), while the content of CaOx was lower in the inner than in the outer layers (57.6 vs. 86.6%; P<0.05). In CaP stones, the content of CA.AP in the nuclear layers was higher than that in the outer layers (74.0 vs. 47.3%; P<0.05), while the content of CaOx was lower in the inner than in the outer layers (7.0 vs. 40.0%; P<0.05). The UA stones showed no significant differences in their composition among different layers. In conclusion, FT-IR analysis of various layers of human upper urinary tract stones revealed that CaOx and CaP stones showed differences in composition between their core and surface, while all of the UA calculi were pure stones. The composition showed a marked variation among different layers of the stones, indicating that metabolism has an important role in different phases of the evolution of stones. The present study provided novel insight into the pathogenesis of urinary tract stones and may contribute to their prevention and treatment. PMID:28912866

The Mars water cycle at other epochs - Recent history of the polar caps and layered terrain

NASA Technical Reports Server (NTRS)

Jakosky, Bruce M.; Henderson, Bradley G.; Mellon, Michael T.

1993-01-01

A numerical model is presented of the integrated role of seasonal water cycle on the evolution of polar deposits on Mars over the last 10 million years. From the model, it is concluded that the only major difference between the polar caps which affects their long-term behavior is ultimately the difference in their elevations. Because of that difference, there is a preference for CO2 frost to stay longer on the northern polar cap. The average difference in sublimation at the caps results in a net south-to-north transport of water ice over long time scales. Superimposed on any long-term behavior is a transfer of water ice between the caps on the 10 exp 5 - 10 exp 6 yr time scales. The amount of water exchanged is small compared to the total ice content of the polar deposits.

The Mars water cycle at other epochs - Recent history of the polar caps and layered terrain

NASA Astrophysics Data System (ADS)

Jakosky, B. M.; Henderson, B. G.; Mellon, M. T.

1993-04-01

A numerical model is presented of the integrated role of seasonal water cycle on the evolution of polar deposits on Mars over the last 10 million years. From the model, it is concluded that the only major difference between the polar caps which affects their long-term behavior is ultimately the difference in their elevations. Because of that difference, there is a preference for CO2 frost to stay longer on the northern polar cap. The average difference in sublimation at the caps results in a net south-to-north transport of water ice over long time scales. Superimposed on any long-term behavior is a transfer of water ice between the caps on the 10 exp 5 - 10 exp 6 yr time scales. The amount of water exchanged is small compared to the total ice content of the polar deposits.

Temperature Distribution within a Cold Cap during Nuclear Waste Vitrification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixon, Derek R.; Schweiger, Michael J.; Riley, Brian J.

2015-07-21

The kinetics of the feed-to-glass conversion affects the waste vitrification rate in an electric melter. The primary area of interest in this conversion process is the cold cap, a layer of reacting feed on top of molten glass. Knowing the temperature profile within a cold cap will help determine its characteristics and relate them to the rate of glass production. The work presented here provides an experimental determination of the temperature distribution within the cold cap. Since a direct measurement of the temperature field within the cold cap is impracticable, an indirect method was developed where the textural features inmore » a laboratory-made cold cap with a high-level waste feed were mapped as a function of position using optical microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction. To correlate the temperature distribution to microstructures within the cold cap, microstructures were identified of individual feed samples that were heat treated to set temperatures between 400°C and 1200°C and quenched. The temperature distribution within the cold cap was then established by correlating cold-cap regions with the feed samples of nearly identical structures and was compared with the temperature profile from a mathematical model.« less

Investigation on Surface Polarization of Al2O3-capped GaN/AlGaN/GaN Heterostructure by Angle-Resolved X-ray Photoelectron Spectroscopy.

PubMed

Duan, Tian Li; Pan, Ji Sheng; Wang, Ning; Cheng, Kai; Yu, Hong Yu

2017-08-17

The surface polarization of Ga-face gallium nitride (GaN) (2 nm)/AlGaN (22 nm)/GaN channel (150 nm)/buffer/Si with Al 2 O 3 capping layer is investigated by angle-resolved X-ray photoelectron spectroscopy (ARXPS). It is found that the energy band varies from upward bending to downward bending in the interface region, which is believed to be corresponding to the polarization variation. An interfacial layer is formed between top GaN and Al 2 O 3 due to the occurrence of Ga-N bond break and Ga-O bond forming during Al 2 O 3 deposition via the atomic layer deposition (ALD). This interfacial layer is believed to eliminate the GaN polarization, thus reducing the polarization-induced negative charges. Furthermore, this interfacial layer plays a key role for the introduction of the positive charges which lead the energy band downward. Finally, a N 2 annealing at 400 °C is observed to enhance the interfacial layer growth thus increasing the density of positive charges.

Two-Dimensional Polymer Synthesized via Solid-State Polymerization for High-Performance Supercapacitors.

PubMed

Liu, Wei; Ulaganathan, Mani; Abdelwahab, Ibrahim; Luo, Xin; Chen, Zhongxin; Rong Tan, Sherman Jun; Wang, Xiaowei; Liu, Yanpeng; Geng, Dechao; Bao, Yang; Chen, Jianyi; Loh, Kian Ping

2018-01-23

Two-dimensional (2-D) polymer has properties that are attractive for energy storage applications because of its combination of heteroatoms, porosities and layered structure, which provides redox chemistry and ion diffusion routes through the 2-D planes and 1-D channels. Here, conjugated aromatic polymers (CAPs) were synthesized in quantitative yield via solid-state polymerization of phenazine-based precursor crystals. By choosing flat molecules (2-TBTBP and 3-TBQP) with different positions of bromine substituents on a phenazine-derived scaffold, C-C cross coupling was induced following thermal debromination. CAP-2 is polymerized from monomers that have been prepacked into layered structure (3-TBQP). It can be mechanically exfoliated into micrometer-sized ultrathin sheets that show sharp Raman peaks which reflect conformational ordering. CAP-2 has a dominant pore size of ∼0.8 nm; when applied as an asymmetric supercapacitor, it delivers a specific capacitance of 233 F g -1 at a current density of 1.0 A g -1 , and shows outstanding cycle performance.

Photoluminescence Study of Plasma-Induced Damage of GaInN Single Quantum Well

NASA Astrophysics Data System (ADS)

Izumi, Shouichiro; Minami, Masaki; Kamada, Michiru; Tatsumi, Tetsuya; Yamaguchi, Atsushi A.; Ishikawa, Kenji; Hori, Masaru; Tomiya, Shigetaka

2013-08-01

Plasma-induced damage (PID) due to Cl2/SiCl4/Ar plasma etching of the GaN capping layer (CAP)/GaInN single quantum well (SQW)/GaN structure was investigated by conventional photoluminescence (PL), transmission electron microscopy (TEM), and time-resolved and temperature-dependent photoluminescence (TRPL). SQW PL intensity remained constant initially, although plasma etching of the CAP layer proceeded, but when the etching thickness reached a certain amount (˜60 nm above the SQW), PL intensity started to decrease sharply. On the other hand, TEM observations show that the physical damage (structural damage) was limited to the topmost surface region. These findings can be explained by the results of TRPL studies, which revealed that there exist two different causes of PID. One is an increase in the number of nonradiative recombination centers, which mainly affects the PL intensity. The other is an increase in the quantum level fluctuation owing mainly to physical damage.

Constraints on the Composition and Evolution of the Lunar Crust from Meteorite NWA 3163

NASA Technical Reports Server (NTRS)

McLeod, C. L.; Brandon, A. D.; Fernandes, V. A.; Peslier, A. H.; Lapen, T. J.; Irving, A. J.

2013-01-01

The lunar meteorite NWA 3163 (paired with NWA 4881, 4483) is a ferroan, feldspathic granulitic breccia characterized by pigeonite, augite, olivine, maskelynite and accessory Tichromite, ilmenite and troilite. Bulk rock geochemical signatures indicate the lack of a KREEP- derived component (Eu/Eu* = 3.47), consistent with previously studied lunar granulites and anorthosites. Bulk rock chondrite-normalized signatures are however distinct from the anorthosites and granulites sampled by Apollo missions and are relatively REE-depleted. In-situ analyses of maskelynite reveal little variation in anorthite content (average An% is 96.9 +/- 1.6, 2 sigma). Olivine is relatively ferroan and exhibits very little variation in forsterite content with mean Fo% of 57.7 +/- 2.0 (2 sigma). The majority of pyroxene is low-Ca pigeonite (En57Fs33Wo10). Augite (En46Fs21Wo33) is less common, comprising approximately 10% of analyzed pyroxene. Two pyroxene thermometry on co-existing orthopyroxene and augite yield an equilibrium temperature of 1070C which is in reasonable agreement with temperatures of 1096C estimated from pigeonite compositions. Rb-Sr isotopic systematics of separated fractions yield an average measured Sr-87/Sr-87 of 0.699282+/-0.000007 (2 sigma). Sr model ages are calculated using a modern day Sr-87/Sr-86 Basaltic Achondrite Best Initial (BABI) value of 0.70475, from an initial BABI value Sr-87/Sr-86 of 0.69891 and a corresponding Rb-87/Sr-97 of 0.08716. The Sr model Thermomechanical analysis (TMA) age, which represents the time of separation of a melt from a source reservoir having chondritic evolution, is 4.56+/-0.1 Ga. A Sr model T(sub RD) age, which is a Rb depletion age and assumes no contribution from Rb in the sample in the calculation, yields 4.34+/-0.1 Ga (i.e. a minimum age). The Ar-Ar dating of paired meteorite NWA 4881 reveals an age of c. 2 Ga, likely representing the last thermal event this meteorite experienced. An older Ar-40/Ar-39 age of c. 3.5 Ga may record the thermal event which produced the granulitic texture. Additional chronological constraints will be provided by Sm-Nd systematics. Ferroan Anorthosites like NWA 3163 have been interpreted to represent direct lunar magma ocean (LMO) crystallization products. If this is the case, trace element concentrations in NWA 3163 primary mineral phases should be in equilibrium with residual LMO liquids present during crystallization of those phases. Results from petrogenetic modeling suggest that the NWA 3163 protolith did not form from crystallization of an initially LREE depleted LMO but rather require an initially chondritic LMO with early garnet crystallization. Furthermore, a two-stage crystallization model where plagioclase crystalized prior to pyroxene (93% vs. 99.5% of LMO crystallization) is implied.

Integration of Porogen-Based Low-k Films: Influence of Capping Layer Thickness and Long Thermal Anneals on Low-k Damage and Reliability

NASA Astrophysics Data System (ADS)

De Roest, David; Vereecke, Bart; Huffman, Craig; Heylen, Nancy; Croes, Kristof; Arai, Hirofumi; Takamure, Noboru; Beynet, Julien; Sprey, Hessel; Matsushita, Kiyohiro; Kobayashi, Nobuyoshi; Verdonck, Patrick; Demuynck, Steven; Beyer, Gerald; Tokei, Zsolt; Struyf, Herbert

2010-05-01

This paper discusses integration aspects of a porous low-k film (k ˜2.45) cured with a broadband UV lamp. Different process splits are discussed which could contribute to avoid integration induced damage and improve reliability. The main factor contributing to a successful integration is the presence of a thick (protecting) cap layer partially remaining after chemical mechanical polishing (CMP), which leads to yielding structures with a keff of ˜2.6, a breakdown voltage of ˜6.9 MV/cm and time dependent dielectric breakdown (TDDB) lifetimes in the excess of 100 years. Long thermal anneals restore the k-value but degrade lifetime.

CryoScout: A Descent Through the Mars Polar Cap

NASA Technical Reports Server (NTRS)

Hecht, M. H.; Saunders, R. S.

2003-01-01

CryoScout was proposed as a subsurface investigation of the stratigraphic climate record embedded in Mars North Polar cap. After landing on a gentle landscape in the midst of the mild summer season, CryoScout was to use the continuous polar sunlight to power the descent of a cryobot, a thermal probe, into the ice at a rate of about 1 m per day. CryoScout would probe deep enough into this time capsule to see the effects of planetary obliquity variations and discrete events such as dust storms or volcanic eruptions. By penetrating tens of meters of ice, the mission would explore at least one of the dominant "MOC layers" observed in exposed layered terrain.

Room-temperature codeposition growth technique for pinhole reduction in epitaxial CoSi2 on Si (111)

NASA Technical Reports Server (NTRS)

Lin, T. L.; Fathauer, R. W.; Grunthaner, P. J.; D'Anterroches, C.

1988-01-01

A solid-phase epitaxy has been developed for the growth of CoSi2 films on Si (111) with no observable pinholes (1000/sq cm detection limit). The technique utilizes room-temperature codeposition of Co and Si in stoichiometric ratio, followed by the deposition of an amorphous Si capping layer and subsequent in situ annealing at 550-600 C. CoSi2 films grown without the Si cap are found to have pinhole densities of (1-10) x 10 to the 7th/sq cm when annealed at similar temperatures. A CF4 plasma-etching technique was used to increase the visibility of the pinholes in the silicide layer.

Hybrid III-V on Si grating as a broadband reflector and a high-Q resonator

NASA Astrophysics Data System (ADS)

Chung, Il-Sug; Taghizadeh, Alireza; Park, Gyeong Cheol

2016-03-01

Hybrid grating (HG) with a high-refractive-index cap layer added onto a high contrast grating (HCG), can provide a high reflectance close 100 % over a broader wavelength range than HCGs, or work as a ultrahigh quality (Q) factor resonator. The reflection and resonance properties of HGs have been investigated and the mechanisms leading to these properties are discussed. A HG reflector sample integrating a III-V cap layer with InGaAlAs quantum wells onto a Si grating has been fabricated and its reflection property has been characterized. The HG-based lasers have a promising prospect for silicon photonics light source or high-speed laser applications.

Studies of Martian polar regions. [using CO2 flow

NASA Technical Reports Server (NTRS)

Smith, C. I.; Clark, B. R.; Eschman, D. F.

1974-01-01

The flow law determined experimentally for solid CO2 establishes that an hypothesis of glacial flow of CO2 at the Martian poles is not physically unrealistic. Compression experiments carried out under 1 atmosphere pressure and constant strain rate conditions demonstrate that the strength of CO2 near its sublimation point is considerably less than the strength of water ice near its melting point. A plausible glacial model for the Martian polar caps was constructed. The CO2 deposited near the pole would have flowed outward laterally to relieve high internal shear stresses. The topography of the polar caps, and the uniform layering and general extent of the layered deposits were explained using this model.

Enhanced characteristics of blue InGaN /GaN light-emitting diodes by using selective activation to modulate the lateral current spreading length

NASA Astrophysics Data System (ADS)

Lin, Ray-Ming; Lu, Yuan-Chieh; Chou, Yi-Lun; Chen, Guo-Hsing; Lin, Yung-Hsiang; Wu, Meng-Chyi

2008-06-01

We have studied the characteristics of blue InGaN /GaN multiquantum-well light-emitting diodes (LEDs) after reducing the length of the lateral current path through the transparent layer through formation of a peripheral high-resistance current-blocking region in the Mg-doped GaN layer. To study the mechanism of selective activation in the Mg-doped GaN layer, we deposited titanium (Ti), gold (Au), Ti /Au, silver, and copper individually onto the Mg-doped GaN layer and investigated their effects on the hole concentration in the p-GaN layer. The Mg-doped GaN layer capped with Ti effectively depressed the hole concentration in the p-GaN layer by over one order of magnitude relative to that of the as-grown layer. This may suggest that high resistive regions are formed by diffusion of Ti and depth of high resistive region from the p-GaN surface depends on the capped Ti film thickness. Selective activation of the Mg-doped GaN layer could be used to modulate the length of the lateral current path. Furthermore, the external quantum efficiency of the LEDs was improved significantly after reducing the lateral current spreading length. In our best result, the external quantum efficiency was 52.3% higher (at 100mA) than that of the as-grown blue LEDs.

Materials and methods for the preparation of nanocomposites

DOEpatents

Nag, Angshuman; Talapin, Dmitri V.

2018-01-30

Disclosed herein is an isolable colloidal particle comprising a nanoparticle and an inorganic capping agent bound to the surface of the nanoparticle, a method for making the same in a biphasic solvent mixture, and the formation of structures and solids from the isolable colloidal particle. The process can yield photovoltaic cells, piezoelectric crystals, thermoelectric layers, optoelectronic layers, light emitting diodes, ferroelectric layers, thin film transistors, floating gate memory devices, phase change layers, and sensor devices.

Sciencepoetry and Language/Culture Teaching.

ERIC Educational Resources Information Center

Romano, James V.

1988-01-01

Examines Rafael Catala's notion of sciencepoetry and an application of modern scientific principles to the teaching of language and culture, the "Lange Process." This interactive language/culture learning process relates target and native languages, culture, and perceptions. (Author/LMO)

Aspiration, Expectation, and Parental Influences among Upward Bound Students in Three Institutions.

ERIC Educational Resources Information Center

Mims, George L.

1985-01-01

The purpose of this study was to investigate aspiration, expectation, and parental influence and the extent to which these variables manifest themselves among 210 Upward Bound students in three institutions. (Author/LMO)

Reprogramming mouse fibroblasts into engraftable myeloerythroid and lymphoid progenitors

PubMed Central

Cheng, Hui; Ang, Heather Yin-Kuan; A. EL Farran, Chadi; Li, Pin; Fang, Hai Tong; Liu, Tong Ming; Kong, Say Li; Chin, Michael Lingzi; Ling, Wei Yin; Lim, Edwin Kok Hao; Li, Hu; Huber, Tara; Loh, Kyle M.; Loh, Yuin-Han; Lim, Bing

2016-01-01

Recent efforts have attempted to convert non-blood cells into hematopoietic stem cells (HSCs) with the goal of generating blood lineages de novo. Here we show that hematopoietic transcription factors Scl, Lmo2, Runx1 and Bmi1 can convert a developmentally distant lineage (fibroblasts) into ‘induced hematopoietic progenitors' (iHPs). Functionally, iHPs generate acetylcholinesterase+ megakaryocytes and phagocytic myeloid cells in vitro and can also engraft immunodeficient mice, generating myeloerythoid and B-lymphoid cells for up to 4 months in vivo. Molecularly, iHPs transcriptionally resemble native Kit+ hematopoietic progenitors. Mechanistically, reprogramming factor Lmo2 implements a hematopoietic programme in fibroblasts by rapidly binding to and upregulating the Hhex and Gfi1 genes within days. Moreover the reprogramming transcription factors also require extracellular BMP and MEK signalling to cooperatively effectuate reprogramming. Thus, the transcription factors that orchestrate embryonic hematopoiesis can artificially reconstitute this programme in developmentally distant fibroblasts, converting them into engraftable blood progenitors. PMID:27869129

Is plagioclase removal responsible for the negative Eu anomaly in the source regions of mare basalts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shearer, C.K.; Papike, J.J.

1989-12-01

The nearly ubiquitous presence of a negative Eu anomaly in the mare basalts has been suggested to indicate prior separation and flotation of plagioclase from the basalt source region during its crystallization from a lunar magma ocean (LMO). Are there any mare basalts derived from a mantle source which did not experience prior plagioclase separation Crystal chemical rationale for REE substitution in pyroxene suggests that the combination of REE size and charge, M2 site characteristics of pyroxene, fO{sub 2}, magma chemistry, and temperature may account for the negative Eu anomaly in the source region of some types of primitive, lowmore » TiO{sub 2} mare basalts. This origin for the negative Eu anomaly does not preclude the possibility of the LMO as many mare basalts still require prior plagioclase crystallization and separation and/or hybridization involving a KREEP component.« less

Bi-layer sandwich film for antibacterial catheters

PubMed Central

Schamberger, Florian; Zare, Hamideh Heidari; Bröskamp, Sara Felicitas; Jocham, Dieter

2017-01-01

Background: Approximately one quarter of all nosocomial infections can be attributed to the urinary tract. The infections are supposed to be mainly caused by implantations of urethral catheters and stents. A new catheter design is introduced with the aim to lower the high number of nosocomial urethral infections. In order to avoid limitations to use, the design is first applied to conventional commercially available balloon catheters. Results: The main feature of the design is a sandwich layer on both sides of the catheter wall, which is composed of a fragmented base layer of silver capped by a thin film of poly(p-xylylene). This top layer is mainly designed to release a controlled amount of Ag+ ions, which is bactericidal, but not toxic to humans. Simultaneously, the lifetime is prolonged to at least one year. The base layer is electrolessly deposited applying Tollens’ reagens, the cap layer is deposited by using chemical vapor deposition. Conclusion: The three main problems of this process, electroless deposition of a fragmented silver film on the surface of an electrically insulating organic polymer, irreproducible evaporation during heating of the precursor, and exponential decrease of the layer thickness along the capillary, have been solved trough the application of a simple electrochemical reaction and two standard principles of physics: Papin’s pot and the principle of Le Chatelier. PMID:29046846

Bi-layer sandwich film for antibacterial catheters.

PubMed

Franz, Gerhard; Schamberger, Florian; Zare, Hamideh Heidari; Bröskamp, Sara Felicitas; Jocham, Dieter

2017-01-01

Background: Approximately one quarter of all nosocomial infections can be attributed to the urinary tract. The infections are supposed to be mainly caused by implantations of urethral catheters and stents. A new catheter design is introduced with the aim to lower the high number of nosocomial urethral infections. In order to avoid limitations to use, the design is first applied to conventional commercially available balloon catheters. Results: The main feature of the design is a sandwich layer on both sides of the catheter wall, which is composed of a fragmented base layer of silver capped by a thin film of poly( p -xylylene). This top layer is mainly designed to release a controlled amount of Ag + ions, which is bactericidal, but not toxic to humans. Simultaneously, the lifetime is prolonged to at least one year. The base layer is electrolessly deposited applying Tollens' reagens, the cap layer is deposited by using chemical vapor deposition. Conclusion: The three main problems of this process, electroless deposition of a fragmented silver film on the surface of an electrically insulating organic polymer, irreproducible evaporation during heating of the precursor, and exponential decrease of the layer thickness along the capillary, have been solved trough the application of a simple electrochemical reaction and two standard principles of physics: Papin's pot and the principle of Le Chatelier.

Low temperature processed complementary metal oxide semiconductor (CMOS) device by oxidation effect from capping layer.

PubMed

Wang, Zhenwei; Al-Jawhari, Hala A; Nayak, Pradipta K; Caraveo-Frescas, J A; Wei, Nini; Hedhili, M N; Alshareef, H N

2015-04-20

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190 °C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field.

Cleaning of optical surfaces by capacitively coupled RF discharge plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yadav, P. K., E-mail: praveenyadav@rrcat.gov.in; Rai, S. K.; Nayak, M.

2014-04-24

In this paper, we report cleaning of carbon capped molybdenum (Mo) thin film by in-house developed radio frequency (RF) plasma reactor, at different powers and exposure time. Carbon capped Mo films were exposed to oxygen plasma for different durations at three different power settings, at a constant pressure. After each exposure, the thickness of the carbon layer and the roughness of the film were determined by hard x-ray reflectivity measurements. It was observed that most of the carbon film got removed in first 15 minutes exposure. A high density layer formed on top of the Mo film was also observedmore » and it was noted that this layer cannot be removed by successive exposures at different powers. A significant improvement in interface roughness with a slight improvement in top film roughness was observed. The surface roughness of the exposed and unexposed samples was also confirmed by atomic force microscopy measurements.« less

Low Temperature Processed Complementary Metal Oxide Semiconductor (CMOS) Device by Oxidation Effect from Capping Layer

PubMed Central

Wang, Zhenwei; Al-Jawhari, Hala A.; Nayak, Pradipta K.; Caraveo-Frescas, J. A.; Wei, Nini; Hedhili, M. N.; Alshareef, H. N.

2015-01-01

In this report, both p- and n-type tin oxide thin-film transistors (TFTs) were simultaneously achieved using single-step deposition of the tin oxide channel layer. The tuning of charge carrier polarity in the tin oxide channel is achieved by selectively depositing a copper oxide capping layer on top of tin oxide, which serves as an oxygen source, providing additional oxygen to form an n-type tin dioxide phase. The oxidation process can be realized by annealing at temperature as low as 190°C in air, which is significantly lower than the temperature generally required to form tin dioxide. Based on this approach, CMOS inverters based entirely on tin oxide TFTs were fabricated. Our method provides a solution to lower the process temperature for tin dioxide phase, which facilitates the application of this transparent oxide semiconductor in emerging electronic devices field. PMID:25892711

Complex Burial and Exhumation of South Polar Cap Pitted Terrain

NASA Technical Reports Server (NTRS)

2000-01-01

This image is illuminated by sunlight from the upper left. The two prominent bright stripes at the left/center of the image are covered with bright frost and thus create the illusion that they are sunlit from the lower left.

The large pits, troughs, and 'swiss cheese' of the south polar residual cap appear to have been formed in the upper 4 or 5 layers of the polar material. Each layer is approximately 2 meters (6.6 feet) thick. Some Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) images of this terrain show examples in which older pitted and eroded layers have been previously buried and are now being exhumed. The example shown here includes two narrow, diagonal slopes that trend from upper left toward lower right at the left/center portion of the frame. Along the bottoms of these slopes are revealed a layer that underlies them in which there are many more pits and troughs than in the upper layer. It is likely in this case that the lower layer formed its pits and troughs before it was covered by the upper layer. This observation suggests that the troughs, pits, and 'swiss cheese' features of the south polar cap are very old and form over long time scales.

The picture is located near 84.6oS, 45.1oW, and covers an area 3 km by 5 km (1.9 x 3.1 mi) at a resolution of about 3.8 meters (12 ft) per pixel. The image was taken during southern spring on August 29, 1999.

Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

Testing the "Mudball Earth" Hypothesis: Are Neoproterozoic Glacial Deposits Capped with Supraglacial Dust?

NASA Astrophysics Data System (ADS)

Goodman, J. C.; Alvim Lage, C.

2014-12-01

The Snowball Earth hypothesis has inspired several variants which may help to explain some of the great mysteries of the Neoproterozoic glaciations. One of these, the "Mudball Earth", proposes that as the Earth remained completely frozen for millions of years, a layer of dust accumulated on the ice surface. This dust layer would darken the planet, making it easier for the Earth to escape from the highly stable snowball climate state. This hypothesis is testable: after the ice melted at the end of a glacial era, this dust would sink to the bottom of the ocean, possibly forming a distinct clay, mud, or silt layer on the top of the glacial till deposits: this "clay drape" would then be covered by the cap carbonates that mark a return to warm climate. Sublimation and ice flow during the glacial episode should make this layer thicker at the equator and thinner or absent in the poles. Is this clay layer actually present in the rock record? Is it more prevalent at the paleoequator, as predicted? A clay drape has been noticed anecdotally, but no global survey has been done to date. We conducted a thorough literature review of all sites where Neoproterozoic glacial diamictites have been observed, identifying the type of rock that lies between the diamictite and the postglacial cap carbonate, when present, during both Sturtian and Marinoan glacial periods. Only a few publications identify a distinct clay/silt/mud layer that might represent weathered dust. These sites are not grouped by paleolatitude in any obvious way. With access only to published reports, we cannot determine whether such a layer is absent, went unreported, or was misinterpreted by us. With this work we hope to attract the attention of Neoproterozoic field geologists, inviting them to comment on the presence or absence of strata which could confirm or reject the "Mudball" hypothesis.

Tuning the interfacial charge, orbital, and spin polarization properties in La0.67Sr0.33MnO3/La1-xSrxMnO3 bilayers

NASA Astrophysics Data System (ADS)

Carreira, Santiago J.; Aguirre, Myriam H.; Briatico, Javier; Weschke, Eugen; Steren, Laura B.

2018-01-01

The possibility of controlling the interfacial properties of artificial oxide heterostructures is still attracting researchers in the field of materials engineering. Here, we used surface sensitive techniques and high-resolution transmission electron microscopy to investigate the evolution of the surface spin-polarization and lattice strains across the interfaces between La0.66Sr0.33MnO3 thin films and low-doped manganites as capping layers. We have been able to fine tune the interfacial spin-polarization by changing the capping layer thickness and composition. The spin-polarization was found to be the highest at a critical capping thickness that depends on the Sr doping. We explain the non-trivial magnetic profile by the combined effect of two mechanisms: On the one hand, the extra carriers supplied by the low-doped manganites that tend to compensate the overdoped interface, favouring locally a ferromagnetic double-exchange coupling. On the other hand, the evolution from a tensile-strained structure of the inner layers to a compressed structure at the surface that changes gradually the orbital occupation and hybridization of the 3d-Mn orbitals, being detrimental for the spin polarization. The finding of an intrinsic spin-polarization at the A-site cation observed in x-ray magnetic circular dichroism (XMCD) measurements also reveals the existence of a complex magnetic configuration at the interface, different from the magnetic phases observed at the inner layers.

Ultraviolet emission enhancement in ZnO thin films modified by nanocrystalline TiO2

NASA Astrophysics Data System (ADS)

Zheng, Gaige; Lu, Xi; Qian, Liming; Xian, Fenglin

2017-05-01

In this study, nanocrystalline TiO2 modified ZnO thin films were prepared by electron beam evaporation. The structural, morphological and optical properties of the samples were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), UV-visible spectroscopy, fluorescence spectroscopy, respectively. The composition of the films was examined by energy dispersive X-ray spectroscopy (EDX). The photoluminescent spectrum shows that the pure ZnO thin film exhibits an ultraviolet (UV) emission peak and a strong green emission band. Surface analysis indicates that the ZnO thin film contains many oxygen vacancy defects on the surface. After the ZnO thin film is modified by the nanocrystalline TiO2 layer, the UV emission of ZnO is largely enhanced and the green emission is greatly suppressed, which suggests that the surface defects such as oxygen vacancies are passivated by the TiO2 capping layer. As for the UV emission enhancement of the ZnO thin film, the optimized thickness of the TiO2 capping layer is ∼16 nm. When the thickness is larger than 16 nm, the UV emission of the ZnO thin film will decrease because the TiO2 capping layer absorbs most of the excitation energy. The UV emission enhancement in the nanocrystalline TiO2 modified ZnO thin film can be attributed to surface passivation and flat band effect.

Linking Dynamics of the Near-surface Flow to Deeper Boundary Layer Forcing in the Nocturnal Boundary Layer

DTIC Science & Technology

2012-06-01

Kaimal and Finnigan (1994), modified) Figure 2.2 illustrates the evolution from unstable CBL to a nocturnal Stable Bound- ary Layer ( SBL ) in the absence...mixed layer acts as a cap for the SBL . The SBL persists through the night until sunrise when surface heating resumes and a new unstable layer begins...to form at the surface, gradually returning to a CBL. 7 2.2.1 Dynamics of the stable boundary layer Because the SBL is stably stratified, buoyancy

Buffer layers for REBCO films for use in superconducting devices

DOEpatents

Goyal, Amit; Wee, Sung-Hun

2014-06-10

A superconducting article includes a substrate having a biaxially textured surface. A biaxially textured buffer layer, which can be a cap layer, is supported by the substrate. The buffer layer includes a double perovskite of the formula A.sub.2B'B''O.sub.6, where A is rare earth or alkaline earth metal and B' and B'' are different transition metal cations. A biaxially textured superconductor layer is deposited so as to be supported by the buffer layer. A method of making a superconducting article is also disclosed.

Phosphate-based glass fiber vs. bulk glass: Change in fiber optical response to probe in vitro glass reactivity.

PubMed

Massera, J; Ahmed, I; Petit, L; Aallos, V; Hupa, L

2014-04-01

This paper investigates the effect of fiber drawing on the thermal and structural properties as well as on the glass reactivity of a phosphate glass in tris(hydroxymethyl)aminomethane-buffered (TRIS) solution and simulated body fluid (SBF). The changes induced in the thermal properties suggest that the fiber drawing process leads to a weakening and probable re-orientation of the POP bonds. Whereas the fiber drawing did not significantly impact the release of P and Ca, an increase in the release of Na into the solution was noticed. This was probably due to small structural reorientations occurring during the fiber drawing process and to a slight diffusion of Na to the fiber surface. Both the powders from the bulk and the glass fibers formed a Ca-P surface layer when immersed in SBF and TRIS. The layer thickness was higher in the calcium and phosphate supersaturated SBF than in TRIS. This paper for the first time presents the in vitro reactivity and optical response of a phosphate-based bioactive glass (PBG) fiber when immersed in SBF. The light intensity remained constant for the first 48h after which a decrease with three distinct slopes was observed: the first decrease between 48 and 200h of immersion could be correlated to the formation of the Ca-P layer at the fiber surface. After this a faster decrease in light transmission was observed from 200 to ~425h in SBF. SEM analysis suggested that after 200h, the surface of the fiber was fully covered by a thin Ca-P layer which is likely to scatter light. For immersion times longer than ~425h, the thickness of the Ca-P layer increased and thus acted as a barrier to the dissolution process limiting further reduction in light transmission. The tracking of light transmission through the PBG fiber allowed monitoring of the fiber dissolution in vitro. These results are essential in developing new bioactive fiber sensors that can be used to monitor bioresponse in situ. Copyright © 2014 Elsevier B.V. All rights reserved.

Comparing XPS on bare and capped ZrN films grown by plasma enhanced ALD: Effect of ambient oxidation

NASA Astrophysics Data System (ADS)

Muneshwar, Triratna; Cadien, Ken

2018-03-01

In this article we compare x-ray photoelectron spectroscopy (XPS) measurements on bare- and capped- zirconium nitride (ZrN) films to investigate the effect of ambient sample oxidation on the detected bound O in the form of oxide ZrO2 and/or oxynitride ZrOxNy. ZrN films in both bare- and Al2O3/AlN capped- XPS samples were grown by plasma-enhanced atomic layer deposition (PEALD) technique using tetrakis dimethylamino zirconium (TDMAZr) precursor, forming gas (5% H2, rest N2) inductively coupled plasma (ICP), and as received research grade process gases under identical process conditions. Capped samples were prepared by depositing 1 nm thick PEALD AlN on ZrN, followed by additional deposition of 1 nm thick ALD Al2O3, without venting of ALD reactor. On bare ZrN sample at room temperature, spectroscopic ellipsometry (SE) measurements with increasing ambient exposure times (texp) showed a self-limiting surface oxidation with the oxide thickness (dox) approaching 3.7 ± 0.02 nm for texp > 120 min. In XPS data measured prior to sample sputtering (tsput = 0), ZrO2 and ZrOxNy were detected in bare- samples, whereas only ZrN and Al2O3/AlN from capping layer were detected in capped- samples. For bare-ZrN samples, appearance of ZrO2 and ZrOxNy up to sputter depth (dsput) of 15 nm in depth-profile XPS data is in contradiction with measured dox = 3.7 nm, but explained from sputtering induced atomic inter-diffusion within analyzed sample. Appearance of artifacts in the XPS spectra from moderately sputtered (dsput = 0.2 nm and 0.4 nm) capped-ZrN sample, provides an evidence to ion-bombardment induced modifications within analyzed sample.

Quantitative structure-retention relationships of polycyclic aromatic hydrocarbons gas-chromatographic retention indices.

PubMed

Drosos, Juan Carlos; Viola-Rhenals, Maricela; Vivas-Reyes, Ricardo

2010-06-25

Polycyclic aromatic compounds (PAHs) are of concern in environmental chemistry and toxicology. In the present work, a QSRR study was performed for 209 previously reported PAHs using quantum mechanics and other sources descriptors estimated by different approaches. The B3LYP/6-31G* level of theory was used for geometrical optimization and quantum mechanics related variables. A good linear relationship between gas-chromatographic retention index and electronic or topologic descriptors was found by stepwise linear regression analysis. The molecular polarizability (alpha) and the second order molecular connectivity Kier and Hall index ((2)chi) showed evidence of significant correlation with retention index by means of important squared coefficient of determination, (R(2)), values (R(2)=0.950 and 0.962, respectively). A one variable QSRR model is presented for each descriptor and both models demonstrates a significant predictive capacity established using the leave-many-out LMO (excluding 25% of rows) cross validation method's q(2) cross-validation coefficients q(2)(CV-LMO25%), (obtained q(2)(CV-LMO25%) 0.947 and 0.960, respectively). Furthermore, the physicochemical interpretation of selected descriptors allowed detailed explanation of the source of the observed statistical correlation. The model analysis suggests that only one descriptor is sufficient to establish a consistent retention index-structure relationship. Moderate or non-significant improve was observed for quantitative results or statistical validation parameters when introducing more terms in predictive equation. The one parameter QSRR proposed model offers a consistent scheme to predict chromatographic properties of PAHs compounds. Copyright 2010 Elsevier B.V. All rights reserved.

Experimental Study of the Partitioning of Siderophile Elements in a Crystallizing Lunar Magma Ocean

NASA Technical Reports Server (NTRS)

Galenas, M.; Righter, K.; Danielson, L.; Pando, K.; Walker, R. J.

2012-01-01

The distributions of trace elements between the lunar interior and pristine crustal rocks were controlled by the composition of starting materials, lunar core formation, and crystallization of the lunar magma ocean (LMO) [1]. This study focuses on the partitioning of highly siderophile elements (HSE) including Re, Os, Ir, Ru, Pt, Rh, Pd and Au as well as the moderately siderophile elements Mo and W, and the lithophile elements of Hf and Sr. Our experiments also include Ga, which can be slightly siderophile, but is mostly considered to be chalcophile. Partitioning of these elements is not well known at the conditions of a crystallizing LMO. Previous studies of HSE partitioning in silicate systems have yielded highly variable results for differing oxygen fugacity (fO2) and pressure [2-4]. For example, under certain conditions Pt is compatible in clinopy-roxene [2] and Rh and Ru are compatible in olivine [3]. The silicate compositions used for these experiments were nominally basaltic. Ruthenium, Rh, and Pd are incompatible in plagioclase under these conditions[4]. However, this latter study was done at extremely oxidizing conditions and at atmospheric pressure, possibly limiting the applicability for consideration of conditions of a crystallizing LMO. In this study we address the effects of pressure and oxygen fugacity on the crystal/liquid partition coefficients of these trace elements. We are especially interested in the plagioclase/melt partition coefficients so that it may be possible to use reverse modeling to constrain the concentrations of these elements in the lunar mantle through their abundances in pristine crustal rocks.

Cationic Intermixing and Reactivity at the La2 Mo2 O9 /La0.8 Sr0.2 MnO3-δ Solid Oxide Fuel Cell Electrolyte-Cathode Interface.

PubMed

Ravella, Uday K; Liu, Jingjing; Corbel, Gwenaël; Skinner, Stephen J; Lacorre, Philippe

2016-08-23

Among standard high-temperature cathode materials for solid oxide fuel cells, La0.8 Sr0.2 MnO3-δ (LSM) displays the least reactivity with the oxide-ion conductor La2 Mo2 O9 (LMO), yet a reaction is observed at high processing temperatures, identified by using XRD and focused ion beam secondary-ion mass spectrometry (FIB-SIMS) after annealing at 1050 and 1150 °C. Additionally, Sr and Mn solutions were deposited and annealed on LMO pellets, as well as a Mo solution on a LSM pellet. From these studies several reaction products were identified by using XRD and located by using FIB-SIMS on the surface of pelletised samples. We used depth profiling to show that the reactivity extended up to ∼10 μm from the surface region. If Sr was present, a SrMoO4 -type scheelite phase was always observed as a reaction product, and if Mn was present, LaMnO3+δ single crystals were observed on the surface of the LMO pellets. Additional phases such as La2 MoO6 and La6 MoO12 were also detected depending on the configuration and annealing temperature. Reaction mechanisms and detailed reaction formulae are proposed to explain these observations. The strongest driving force for cationic diffusion appears to originate from Mo(6+) and Mn(3+) cations, rather than from Sr(2+) . © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analysis of Factors that Influence Infiltration Rates using the HELP Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyer, J.; Shipmon, J.

The Hydrologic Evaluation of Landfill Performance (HELP) model is used by Savannah River National Laboratory (SRNL) in conjunction with PORFLOW groundwater flow simulation software to make longterm predictions of the fate and transport of radionuclides in the environment at radiological waste sites. The work summarized in this report supports preparation of the planned 2018 Performance Assessment for the E-Area Low-Level Waste Facility (LLWF) at the Savannah River Site (SRS). More specifically, this project focused on conducting a sensitivity analysis of infiltration (i.e., the rate at which water travels vertically in soil) through the proposed E-Area LLWF closure cap. A sensitivitymore » analysis was completed using HELP v3.95D to identify the cap design and material property parameters that most impact infiltration rates through the proposed closure cap for a 10,000-year simulation period. The results of the sensitivity analysis indicate that saturated hydraulic conductivity (Ksat) for select cap layers, precipitation rate, surface vegetation type, and geomembrane layer defect density are dominant factors limiting infiltration rate. Interestingly, calculated infiltration rates were substantially influenced by changes in the saturated hydraulic conductivity of the Upper Foundation and Lateral Drainage layers. For example, an order-of-magnitude decrease in Ksat for the Upper Foundation layer lowered the maximum infiltration rate from a base-case 11 inches per year to only two inches per year. Conversely, an order-of-magnitude increase in Ksat led to an increase in infiltration rate from 11 to 15 inches per year. This work and its results provide a framework for quantifying uncertainty in the radionuclide transport and dose models for the planned 2018 E-Area Performance Assessment. Future work will focus on the development of a nonlinear regression model for infiltration rate using Minitab 17® to facilitate execution of probabilistic simulations in the GoldSim® overall system model for the E-Area LLWF.« less

High mobility, dual layer, c-axis aligned crystalline/amorphous IGZO thin film transistor

NASA Astrophysics Data System (ADS)

Chung, Chen-Yang; Zhu, Bin; Greene, Raymond G.; Thompson, Michael O.; Ast, Dieter G.

2015-11-01

We demonstrate a dual layer IGZO thin film transistor (TFT) consisting of a 310 °C deposited c-axis aligned crystal (CAAC) 20 nm thick channel layer capped by a second, 30 nm thick, 260 °C deposited amorphous IGZO layer. The TFT exhibits a saturation field-effect mobility of ˜20 cm2/V s, exceeding the mobility of 50 nm thick single layer reference TFTs fabricated with either material. The deposition temperature of the second layer influences the mobility of the underlying transport layer. When the cap layer is deposited at room temperature (RT), the mobility in the 310 °C deposited CAAC layer is initially low (6.7 cm2/V s), but rises continuously with time over 58 days to 20.5 cm2/V s, i.e., to the same value as when the second layer is deposited at 260 °C. This observation indicates that the two layers equilibrate at RT with a time constant on the order of 5 × 106 s. An analysis based on diffusive transport indicates that the room temperature diffusivity must be of the order of 1 × 10-18 cm2 s-1 with an activation enthalpy EA < 0.2 eV for the mobility limiting species. The findings are consistent with a hypothesis that the amorphous layer deposited on top of the CAAC has a higher solubility for impurities and/or structural defects than the underlying nanocrystalline transport layer, and that the equilibration of the mobility limiting species is rate limited by hydrogen diffusion, whose known diffusivity fits these estimates.

Educating and Training Undergraduate Applied Statisticians.

ERIC Educational Resources Information Center

Peres, Clovis A.; And Others

1985-01-01

A course on Applied Statistics, offered since 1978 at the Instituto de Matematica e Estatistica, Universidade de Sao Paulo, Brasil, is designed to educate statisticians at the bachelor's level for jobs in government statistical offices, industry, and business. (Author/LMO)

Comparison of B{sub 2}O{sub 3} and BN deposited by atomic layer deposition for forming ultrashallow dopant regions by solid state diffusion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Consiglio, Steven, E-mail: steve.consiglio@us.tel.com; Clark, Robert D.; O'Meara, David

2016-01-15

In this study, the authors investigated atomic layer deposition (ALD) of B{sub 2}O{sub 3} and BN for conformal, ultrashallow B doping applications and compared the effect of dopant-containing overlayers on sheet resistance (R{sub s}) and B profiles for both types of films subjected to a drive-in thermal anneal. For the deposition of B{sub 2}O{sub 3}, tris(dimethylamido)borane and O{sub 3} were used as coreactants and for the deposition of BN, BCl{sub 3} and NH{sub 3} were used as coreactants. Due to the extreme air instability of B{sub 2}O{sub 3} films, physical analysis was performed on B{sub 2}O{sub 3} films, which weremore » capped in-situ with ∼30 Å ALD grown Al{sub 2}O{sub 3} layers. For the BN films, in-situ ALD grown Si{sub 3}N{sub 4} capping layers (∼30 Å) were used for comparison. From spectroscopic ellipsometry, a thickness decrease was observed after 1000 °C, 30 s anneal for the B{sub 2}O{sub 3} containing stack with 60 ALD cycles of B{sub 2}O{sub 3}, whereas the BN containing stacks showed negligible thickness decrease after the annealing step, regardless of the number of BN cycles tested. The postanneal reduction in film thickness as well as decrease in R{sub s} for the B{sub 2}O{sub 3} containing stack suggests that the solid state diffusion dopant mechanism is effective, whereas for the BN containing stacks this phenomenon seems to be suppressed. Further clarification of the effectiveness of the B{sub 2}O{sub 3} containing layer compared to the film stacks with BN was evidenced in backside secondary ion mass spectrometry profiling of B atoms. Thus, B{sub 2}O{sub 3} formed by an ALD process and subsequently capped in-situ followed by a drive-in anneal offers promise as a dopant source for ultrashallow doping, whereas the same method using BN seems ineffective. An integrated approach for B{sub 2}O{sub 3} deposition and annealing on a clustered tool also demonstrated controllable R{sub s} reduction without the use of a capping layer.« less

Surface Ages and Resurfacing Rates of the Polar Layered Deposits on Mars

USGS Publications Warehouse

Herkenhoff, K. E.; Plaut, J.J.

2000-01-01

Interpretation of the polar stratigraphy of Mars in terms of global climate changes is complicated by the significant difference in surface ages between the north and south polar layered terrains inferred from crater statistics. We have reassessed the cratering record in both polar regions using Viking Orbiter and Mariner 9 images. No craters have been found in the north polar layered terrain, but the surface of most of the south polar layered deposits appears to have been stable for many of the orbital/axial cycles that are thought to have induced global climate changes on Mars. The inferred surface age of the south polar layered deposits (about 10 Ma) is two orders of magnitude greater than the surface age of the north polar layered deposits and residual cap (at most 100 ka). Similarly, modeled resurfacing rates are at least 20 times greater in the north than in the south. These results are consistent with the hypotheses that polar layered deposit resurfacing rates are highest in areas covered by perennial ice and that the differences in polar resurfacing rates result from the 6.4 km difference in elevation between the polar regions. Deposition on the portion of the south polar layered deposits that is not covered by the perennial ice cap may have ceased about 5 million years ago when the obliquity of Mars no longer exceeded 40??. ?? 2000 Academic Press.

Coordination-based gold nanoparticle layers.

PubMed

Wanunu, Meni; Popovitz-Biro, Ronit; Cohen, Hagai; Vaskevich, Alexander; Rubinstein, Israel

2005-06-29

Gold nanoparticle (NP) mono- and multilayers were constructed on gold surfaces using coordination chemistry. Hydrophilic Au NPs (6.4 nm average core diameter), capped with a monolayer of 6-mercaptohexanol, were modified by partial substitution of bishydroxamic acid disulfide ligand molecules into their capping layer. A monolayer of the ligand-modified Au NPs was assembled via coordination with Zr4+ ions onto a semitransparent Au substrate (15 nm Au, evaporated on silanized glass and annealed) precoated with a self-assembled monolayer of the bishydroxamate disulfide ligand. Layer-by-layer construction of NP multilayers was achieved by alternate binding of Zr4+ ions and ligand-modified NPs onto the first NP layer. Characterization by atomic force microscopy (AFM), ellipsometry, wettability, transmission UV-vis spectroscopy, and cross-sectional transmission electron microscopy showed regular growth of NP layers, with a similar NP density in successive layers and gradually increased roughness. The use of coordination chemistry enables convenient step-by-step assembly of different ligand-possessing components to obtain elaborate structures. This is demonstrated by introducing nanometer-scale vertical spacing between a NP layer and the gold surface, using a coordination-based organic multilayer. Electrical characterization of the NP films was carried out using conductive AFM, emphasizing the barrier properties of the organic spacer multilayer. The results exhibit the potential of coordination self-assembly in achieving highly controlled composite nanostructures comprising molecules, NPs, and other ligand-derivatized components.

Evidence of a reduction reaction of oxidized iron/cobalt by boron atoms diffused toward naturally oxidized surface of CoFeB layer during annealing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sato, Soshi, E-mail: sato.soshi@cies.tohoku.ac.jp; Honjo, Hiroaki; Niwa, Masaaki

2015-04-06

We have investigated the redox reaction on the surface of Ta/CoFeB/MgO/CoFeB magnetic tunnel junction stack samples after annealing at 300, 350, and 400 °C for 1 h using angle-resolved X-ray photoelectron spectroscopy for precise analysis of the chemical bonding states. At a capping tantalum layer thickness of 1 nm, both the capping tantalum layer and the surface of the underneath CoFeB layer in the as-deposited stack sample were naturally oxidized. By comparison of the Co 2p and Fe 2p spectra among the as-deposited and annealed samples, reduction of the naturally oxidized cobalt and iron atoms occurred on the surface of the CoFeB layer.more » The reduction reaction was more significant at higher annealing temperature. Oxidized cobalt and iron were reduced by boron atoms that diffused toward the surface of the top CoFeB layer. A single CoFeB layer was prepared on SiO{sub 2}, and a confirmatory evidence of the redox reaction with boron diffusion was obtained by angle-resolved X-ray photoelectron spectroscopy analysis of the naturally oxidized surface of the CoFeB single layer after annealing. The redox reaction is theoretically reasonable based on the Ellingham diagram.« less

One-dimensional cold cap model for melters with bubblers

DOE PAGES

Pokorny, Richard; Hilliard, Zachary J.; Dixon, Derek R.; ...

2015-07-28

The rate of glass production during vitrification in an all-electrical melter greatly impacts the cost and schedule of nuclear waste treatment and immobilization. The feed is charged to the melter on the top of the molten glass, where it forms a layer of reacting and melting material, called the cold cap. During the final stages of the batch-to-glass conversion process, gases evolved from reactions produce primary foam, the growth and collapse of which controls the glass production rate. The mathematical model of the cold cap was revised to include functional representation of primary foam behavior and to account for themore » dry cold cap surface. The melting rate is computed as a response to the dependence of the primary foam collapse temperature on the heating rate and melter operating conditions, including the effect of bubbling on the cold cap bottom and top surface temperatures. The simulation results are in good agreement with experimental data from laboratory-scale and pilot-scale melter studies. Lastly, the cold cap model will become part of the full three-dimensional mathematical model of the waste glass melter.« less

Radar Detection of Layering in Ice: Experiments on a Constructed Layered Ice Sheet

NASA Astrophysics Data System (ADS)

Carter, L. M.; Koenig, L.; Courville, Z.; Ghent, R. R.; Koutnik, M. R.

2016-12-01

The polar caps and glaciers of both Earth and Mars display internal layering that preserves a record of past climate. These layers are apparent both in optical datasets (high resolution images, core samples) and in ground penetrating radar (GPR) data. On Mars, the SHARAD (Shallow Radar) radar on the Mars Reconnaissance Orbiter shows fine layering that changes spatially and with depth across the polar caps. This internal layering has been attributed to changes in fractional dust contamination due to obliquity-induced climate variations, but there are other processes that can lead to internal layers visible in radar data. In particular, terrestrial sounding of ice sheets compared with core samples have revealed that ice density and composition differences account for the majority of the radar reflectors. The large cold rooms and ice laboratory facility at the U.S. Army Cold Regions Research and Engineering Laboratory (CRREL) provide us a unique opportunity to construct experimental ice sheets in a controlled setting and measure them with radar. In a CRREL laboratory, we constructed a layered ice sheet that is 3-m deep with a various snow and ice layers with known dust concentrations (using JSC Mars-1 basaltic simulant) and density differences. These ice sheets were profiled using a commercial GPR, at frequencies of 200, 400 and 900 MHz, to determine how the radar profile changes due to systematic and known changes in snow and ice layers, including layers with sub-wavelength spacing. We will report results from these experiments and implications for interpreting radar-detected layering in ice on Earth and Mars.

Asymmetric metal-insulator-metal (MIM) structure formed by pulsed Nd:YAG laser deposition with titanium nitride (TiN) and aluminum nitride (AlN)

NASA Astrophysics Data System (ADS)

Oshikane, Yasushi

2017-08-01

A novel nanostructured end cap for a truncated conical apex of optical fiber has been studied experimental and numerically. The peculiar cap is composed of asymmetric metal-insulator-metal (MIM) structure coupled with subwavelength holes. The MIM structure may act as reflective band cut filter or generator of surface plasmon polariton (SPP). And nano holes in the thicker metal layer could extract the SPP from the MIM structure and lead it to outer surface of the metal layer. For the purpose, the author has started to create the asymmetric MIM structure with TiN and AlN by pulsed laser deposition (PLD). The resultant structure was diagnosed by spectroscopic analyses.

Spring and Summer Changes at the South Pole as Seen by the Mars Orbiter Camera

NASA Technical Reports Server (NTRS)

Ingersoll, A. P.; Murray, B. C.; Byrne, S.; DeJong, E.; Danielson, G. E.; Herkenhoff, K. E.; Kieffer, H. H.; Soderblom, L. A.

2000-01-01

The Mars Orbiter Camera (MOC) on the Mars Global Surveyor (MGS) spacecraft has been able to follow individual features as the CO2 frost disappears and exposes the material underneath. Because the orbit of MGS is inclined at an angle of 93 degrees relative to the equator, the spacecraft gets especially good coverage of the ring at 87 degrees latitude. The following is a list of phenomena that have been seen during the spring and summer at the South Pole: (1) Circular depressions that are approximately ten meters deep and hundreds of meters in diameter. They are found only within the residual polar cap, the part that survives the summer. The high areas between the depressions are flat-topped mesas whose sides are concave circular arcs. In some places the depressions form patterns that exhibit north-south symmetry, suggesting some control by sunlight; (2) Dark layers that are exposed on the walls of the mesas. Each layer is at most a few meters thick. The dark layers might accumulate during climatic episodes of high atmospheric dust content, or they might accumulate during the annual cycling of dusty CO2; (3) Albedo differences that develop during the summer within the residual cap. These include subtle darkening of the floors of the depressions relative to the mesas and occasional major darkening of the floors, especially near the edge of the cap. The floors and mesas form a distinct stratum, suggesting they represent a distinct compositional boundary. For instance the floors may be water and the mesas may be CO2; (4) Small dark features that appear in spring on the seasonal frost outside the residual cap. Some of the features have parallel tails that are clearly shaped by the wind. Others are more symmetric, like dark snowflakes, with multiple branching arms. After the CO2 frost has disappeared the arms are seen as troughs and the centers as topographic lows; (5) Polygons whose sides are dark troughs. Those that are outside the residual cap seem to disappear when the frost disappears. The polygons and the dark snowflakelike structures may be related, and suggest that CO2 frost may form cohesive slabs; (6) Irregular depressions outside the residual cap. They look like degraded versions of the circular depressions inside the residual cap, and may be a remnant of the cap's changing location; and (7) Areas of burial and exhumation of circular depressions. Thomas et al. give an example with a sharp boundary: On one side the depressions are buried and on the other side they are exposed. In other cases there are rounded troughs up to one kilometer wide, which are dark in summer and appear to have eroded down below the floor of the circular depressions.

Feasibility of 3D printed air slab diode caps for small field dosimetry.

PubMed

Perrett, Benjamin; Charles, Paul; Markwell, Tim; Kairn, Tanya; Crowe, Scott

2017-09-01

Commercial diode detectors used for small field dosimetry introduce a field-size-dependent over-response relative to an ideal, water-equivalent dosimeter due to high density components in the body of the detector. An air gap above the detector introduces a field-size-dependent under-response, and can be used to offset the field-size-dependent detector over-response. Other groups have reported experimental validation of caps containing air gaps for use with several types of diodes in small fields. This paper examines two designs for 3D printed diode air caps for the stereotactic field diode (SFD)-a cap containing a sealed air cavity, and a cap with an air cavity at the face of the SFD. Monte Carlo simulations of both designs were performed to determine dimensions for an air cavity to introduce the desired dosimetric correction. Various parameter changes were also simulated to estimate the dosimetric uncertainties introduced by 3D printing. Cap layer dimensions, cap density changes due to 3D printing, and unwanted air gaps were considered. For the sealed design the optimal air gap size for water-equivalent cap material was 0.6 mm, which increased to 1.0 mm when acrylonitrile butadiene styrene in the cap was simulated. The unsealed design had less variation, a 0.4 mm air gap is optimal in both situations. Unwanted air pockets in the bore of the cap and density changes introduced by the 3D printing process can potentially introduce significant dosimetric effects. These effects may be limited by using fine print resolutions and minimising the volume of cap material.

ESP for Engineers: A Reassessment.

ERIC Educational Resources Information Center

Yin, Koh Moy

1988-01-01

Many foreign engineering undergraduates already have adequate English skills for the technical part of their academic and professional purposes, but still have problems with communication and interactive skills. Conventional ESP courses may not meet their needs, so an alternate program is proposed. (Author/LMO)

Paris Chamber of Commerce Examinations and ACTFL/ETS Proficiency Levels.

ERIC Educational Resources Information Center

Cummins, Patricia W.

1987-01-01

Compares the Paris Chamber of Commerce Exams (both certificate and diploma levels) and the ACTFL Guidelines for language proficiency for the benefit of language teachers. Teaching strategies are suggested for preparing students for the Chamber of Commerce exams. (LMO)

The Effects of Pubertal Timing on Body Image, School Behavior, and Deviance.

ERIC Educational Resources Information Center

Duncan, Paula Duke; And Others

1985-01-01

Data from the National Health Examination Survey, a national probability sample of children and youth aged 12-17, was used to investigate the relationships between maturational timing and body image, school behavior, and deviance. (Author/LMO)

Characterizing near-surface firn from the scattered signal component of glacier surface reflections detected in airborne radio-echo sounding measurements

NASA Astrophysics Data System (ADS)

Rutishauser, A.; Grima, C.; Sharp, M. J.; Blankenship, D. D.; Young, D. A.; Cawkwell, F.; Dowdeswell, J. A.

2016-12-01

With recent summer warming, surface melt on Canadian Arctic ice caps has intensified and extended to higher elevations in ice cap accumulation areas. Consequently, more meltwater percolates into the near-surface firn, and refreezes as ice layers where firn temperatures are below freezing. This process can increase firn densification rates, causing a lowering of the glacier surface height even in the absence of mass changes. Thus, knowledge of spatio-temporal variations in the near-surface firn stratigraphy is important for interpreting altimetrically-derived estimates of ice cap mass balance. We investigate the use of the scattering signal component of glacier surface reflections in airborne radio-echo sounding (RES) measurements to characterize the near-surface firn stratigraphy. The scattering signal distribution over Devon Ice Cap is compared to firn stratigraphy derived from ground-based radar data. We identify three distinct firn facies zones at different elevation ranges. The scattered signal component changes significantly between the different firn facies zones: low scattering correlates to laterally homogeneous firn containing thin, flat and continuous ice layers at elevations above 1800 m and below 1200 m, where firn consists mainly of ice. Higher scattering values are found from 1200-1800 m where the firn contains discrete, undulating ice layers. No correlation was found between the scattering component and surface roughness. Modelled scattering values for the measured roughness were significantly less than the observed values, and did not reproduce their observed spatial distribution. This indicates that the scattering component is determined mainly by the structure of near-surface firn. Our results suggest that the scattering component of surface reflections from airborne RES measurements has potential for characterizing heterogeneity in the spatial structure of firn that is affected by melting and refreezing processes.

Interspace modification of titania-nanorod arrays for efficient mesoscopic perovskite solar cells

NASA Astrophysics Data System (ADS)

Chen, Peng; Jin, Zhixin; Wang, Yinglin; Wang, Meiqi; Chen, Shixin; Zhang, Yang; Wang, Lingling; Zhang, Xintong; Liu, Yichun

2017-04-01

Morphology of electron transport layers (ETLs) has an important influence on the device architecture and electronic processes of mesostructured solar cells. In this work, we thoroughly investigated the effect of the interspace of TiO2 nanorod (NR) arrays on the photovoltaic performance of the perovskite solar cells (PSCs). Along with the interspace in TiO2-NR arrays increasing, the thickness as well as the crystal size of perovskite capping layer are reduced accordingly, and the filling of perovskite in the channel becomes incomplete. Electrochemical impedance spectroscopy measurements reveal that this variation of perovskite absorber layer, induced by interspace of TiO2 NR arrays, causes the change of charge recombination process at the TiO2/perovskite interface, suggesting that a balance between capping layer and the perovskite filling is critical to obtain high charge collection efficiency of PSCs. A power conversion efficiency of 10.3% could be achieved through careful optimization of interspace in TiO2-NR arrays. Our research will shed light on the morphology control of ETLs with 1D structure for heterojunction solar cells fabricated by solution-deposited method.

Materials and methods for the preparation of nanocomposites

DOEpatents

Talapin, Dmitri V.; Kovalenko, Maksym V.; Lee, Jong-Soo; Jiang, Chengyang

2016-05-24

Disclosed herein is an isolable colloidal particle comprising a nanoparticle and an inorganic capping agent bound to the surface of the nanoparticle, a solution of the same, a method for making the same from a biphasic solvent mixture, and the formation of structures and solids from the isolable colloidal particle. The process can yield photovoltaic cells, piezoelectric crystals, thermoelectric layers, optoelectronic layers, light emitting diodes, ferroelectric layers, thin film transistors, floating gate memory devices, imaging devices, phase change layers, and sensor devices.

Improved color coordinates of green monochromatic pc-LED capped with a band-pass filter.

PubMed

Oh, Ji Hye; Yang, Su Ji; Sung, Yeon-Goog; Do, Young Rag

2013-02-25

This study introduces a "greener" green monochromatic phosphor-converted light-emitting diode (pc-LED) using a band-pass filter (BPF) combined with a long-pass dichroic filter (LPDF) and a short-pass dichroic filter (SPDF) to improve the color quality of our previously developed LPDF-capped green pc-LED. This can also address the drawbacks of III-V semiconductor-type green LEDs, which show a low luminous efficacy and a poor current dependence of the efficacy and color coordinates compared to blue semiconductor-type LEDs. The optical properties of green monochromatic pc-LEDs using a BPF are compared with those of LPDF-capped green pc-LEDs, which have a broad band spectrum, and III-V semiconductor-type green LEDs by changing the transmittance wavelength range of the BPF and the peak wavelength of the green phosphors. BPF-capped green monochromatic pc-LEDs provide a high luminous efficacy (134 lm/W at 60 mA), and "greener" 1931 Commission Internationale d'Eclairage (CIE; CIEx, CIEy) color coordinates (0.24, 0.66) owing to the narrowed emission spectrum. We also propose a two-dimensional (2D) polystyrene (PS) microbead (2-μm diameter) monolayer as a scattering layer to overcome the poor angular dependence of the color coordinates of the transmitted light through a nano-multilayered dichroic filter such as an LPDF or BPF. The 2D PS scattering layer improves the angular dependence of the green color emitted from a BPF-capped green pc-LED with only 3% loss of luminous efficacy.

Polarization-Engineered Ga-Face GaN-Based Heterostructures for Normally-Off Heterostructure Field-Effect Transistors

NASA Astrophysics Data System (ADS)

Kim, Hyeongnam; Nath, Digbijoy; Rajan, Siddharth; Lu, Wu

2013-01-01

Polarization-engineered Ga-face GaN-based heterostructures with a GaN cap layer and an AlGaN/ p-GaN back barrier have been designed for normally-off field-effect transistors (FETs). The simulation results show that an unintentionally doped GaN cap and p-GaN layer in the buffer primarily deplete electrons in the channel and the Al0.2Ga0.8N back barrier helps to pinch off the channel. Experimentally, we have demonstrated a normally-off GaN-based field-effect transistor on the designed GaN cap/Al0.3Ga0.7N/GaN channel/Al0.2Ga0.8N/ p-GaN/GaN heterostructure. A positive threshold voltage of 0.2 V and maximum transconductance of 2.6 mS/mm were achieved for 80- μm-long gate devices. The device fabrication process does not require a dry etching process for gate recessing, while highly selective etching of the GaN cap against a very thin Al0.3GaN0.7N top barrier has to be performed to create a two-dimensional electron gas for both the ohmic and access regions. A self-aligned, selective etch of the GaN cap in the access region is introduced, using the gate metal as an etch mask. The absence of gate recess etching is promising for uniform and repeatable threshold voltage control in normally-off AlGaN/GaN heterostructure FETs for power switching applications.

Effect of Silica Particle Size of Nuclear Waste-to-Glass Conversion - 17319

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dixon, Derek R.; Cutforth, Derek A.; Vanderveer, Bradley J.

The process for converting nuclear waste-to-glass in an electric melter occurs in the cold cap, a crust of reacting solids floating on the glass pool. As the melter feed (a mixture of the nuclear waste and glass forming and modifying additives) heats up in the cold cap, glass-forming reactions ensue, causing the feed matrix to connect, trapping reaction gases to create a foam layer. The foam layer reduces the rate of melting by separating the reacting feed from the melt pool. The size of the silica particle additives in the melter feed affects melt viscosity and, hence, foam stability. Tomore » investigate this effect, seven nuclear waste simulant feeds of a high-level waste were batched as slurries and prepared with dissimilar ranges of silica particle size. Each slurry feed was charged into a laboratory-scale melter (LSM) to produce a cold cap and the propensity of feeds to foam was determined by pressing dried feeds into pellets and monitoring the change of pellet volume in response to heating. Two of these slurries were designed to have dissimilar glass viscosities at 1150°C. In the low temperature region of the cold cap, before the melter feed connects, the feeds without fine silica particles behaved similar to the high viscosity feed as their volume contracted while the feed with silica particles no larger than 5 µm reacted like the low viscosity feed. However, the feed volume similarities reversed as the feed connected and expanded through the foam region of the cold cap.« less

Multi-instrument data analysis for interpretation of the Martian North polar layered deposits

NASA Astrophysics Data System (ADS)

Mirino, Melissa; Sefton-Nash, Elliot; Witasse, Olivier; Frigeri, Alessandro

2017-04-01

The Martian polar caps have engendered substantial study due to their spiral morphology, layered structure and the seasonal variability in thickness of the uppermost H2O and CO2 ice layers. We demonstrate a multi-instrument study of exposed and buried north polar layers using data from ESA's Mars Express (MEx) and NASA's Mars Reconnaissance Orbiter (MRO) missions. We perform analysis of high resolution images from MRO's HiRISE, which provide textural and morphological information about surface features larger than 0.3m, with NIR hyperspectral data from MRO CRISM, which allows study of surface mineralogy at a maximum resolution of 18 m/pixel. Stereo-derived topography is provided by MEx's HRSC. Together with these surficial observations we interpret radargrams from MRO SHARAD to obtain information about layered structures at a horizontal resolution between 0.3 and 3 kilometers and a free-space vertical resolution of 15 meters (vertical resolution depends on the dielectric properties of the medium). This combination of datasets allows us to attempt to correlate polar layering, made visible by dielectric interfaces between beds, with surface mineralogies and structures outcropping at specific stratigraphic levels. We analyse two opposite areas of the north polar cap with the intention to characterise in multiple datasets each geologic unit identified in the north polar cap's stratigraphy (mapped by e.g. [1]). We selected deposits observed in Chasma Boreale and Olympia Cavi because these areas allow us to observe and map strata at opposing sides of the north polar cap. Using the CRISM Analysis Tool and spectral summary parameters [2] we map the spectral characteristics of the two areas that show H2O and CO2 ice layering exposed on polar scarps. Through spatial-registration in a GIS with HRSC topography and HiRISE imagery we assess the mineralogical and morphological characteristics of exposed layers. In order to constrain the cross section between the two selected localities we choose SHARAD radargrams that most closely align with the transect between the sites. We interpret sub-horizontal features to be due to dielectric interfaces involving the deposits analysed. Our interpretation of radargrams in the context of compositional and structural constraints, from areas where pertinent beds outcrop, illustrates how joint analysis of surface and sub-surface data can benefit geological interpretation of planetary surfaces and subsurfaces. This technique applied to Mars' north polar layered deposits may offer additional constraint on morphology of internal layering resulting from seasonal deposition/sublimation cycles over varying obliquity [3]. References: [1] Tanaka et al. (2008), Icarus, 196, p. 318-358, doi:10.1016/j.icarus.2008.01.021. [2] Viviano-Beck et al. (2014), J. Geophys. Res. Planets, 119, p. 1403-1431, doi:10.1002/2014JE004627..[3] Putzig et al. (2009), Icarus, 204, p. 443-457, doi:10.1016/j.icarus.2009.07.034.

Diagenesis, weathering and paleoenvironmental conditions from postglacial diamictite/cap carbonate transition layers of the Otavi Group (NW-Namibia)

NASA Astrophysics Data System (ADS)

Gyollai, I.; Popp, F.; Mader, D.; Koeberl, Ch.

2012-04-01

Introduction The so-called "Snowball Earth hypothesis" states that the "Sturtian" (710 Ma) and "Marinoan" glaciations (635 Ma) were of global extent and may have lasted for several million years. Our samples were collected from conspicuous transition layers on top of the glaciogenic Chuos (Sturtian) (10 samples) and Ghaub (Marinoan) formations (63 samples) of the Neoproterozoic Otavi Group in NW-Namibia. The goal of this study is to obtain information concerning the provenance and geochemical composition of postglacial diamictite/cap carbonate transition layers and to estimate the paleoenvironmental conditions with respect to glacio-marine sea water composition and attendant sediment accumulation in mineralogical-geochemical aspects. Methods The mineralogical composition of our samples was studied using the petrographic microscope, X-ray powder diffraction, cathodoluminescence microscopy, and micro-Raman spectrometry. Instrumental neutron activation and X-ray fluorescence analyses, as well as analytical electron microscopy, were used for the geochemical study. Results Detrital components derived from crystalline and/or dolomite platform source areas are enclosed within a diagenetically recrystallized matrix of carbonate and quartz minerals. Clay samples from both, Marinoan and some Sturtian postglacial layers are characterized by high Ni/Co, Cr/V, and low Th/Sc, La/Sc, V/Ni and Cr/Ni ratios compared to PAAS (Postarchean Australian shale, [1]), which could indicate mafic-ultramafic source material[1]. According to SEM-EDX measurements, only hematite, quartz, and feldspar make up the detrital composition, thus the Cr-Ni enrichment does not seem to be associated with any specific mineral phases. Specific results for the Sturtian postglacial transition layers: An U/Th ratio >0.75, and Mo-enrichment in the topmost iron-rich Sturtian diamictites (Chuos Fm.) and their superposed postglacial boundary layers (Rasthof Fm) indicates reducing conditions in the sea water [2,3 ]. The detritus of the basal cap carbonates is rich in kaolinite and montmorillonite and has low K/Cs values, indicating a high weathering rate. Specific results for the Marinoan postglacial transition layers: The Marinoan diamictites (Ghaub Fm.) and their superposed postglacial transition layers (basal Maieberg Fm) are characterized in a few cases by very high Th/Co, Th/Sc and LREE/HREE ratios, which indicate some influence of a felsic source area. The detrital/recrystallized components of these iron-poor diamictites are rich in pyrite and quartz and display a REE enrichment compared to PAAS, which indicates a hydrothermal component during their accumulation [3]. Conlusions 1) Sturtian layers: possibly different source areas supplied the sedimentary basins 2) Marinoan layers : sediments were influenced by hydrothermal fluids and diagenetic alteration 3) Reducing conditions existed in the marine environment during both of the "Snowball Earth" glaciation periods each followed by oxidative conditions reflected in the geochemical composition of related postglacial cap carbonates. Acknowledgement Our work is funded by the Austrian Academy of Sciences (IGCP 512) (to CK).

Reactive composite compositions and mat barriers

DOEpatents

Langton, Christine A.; Narasimhan, Rajendran; Karraker, David G.

2001-01-01

A hazardous material storage area has a reactive multi-layer composite mat which lines an opening into which a reactive backfill and hazardous material are placed. A water-inhibiting cap may cover the hazardous material storage area. The reactive multi-layer composite mat has a backing onto which is placed an active layer which will neutralize or stabilize hazardous waste and a fronting layer so that the active layer is between the fronting and backing layers. The reactive backfill has a reactive agent which can stabilize or neutralize hazardous material and inhibit the movement of the hazardous material through the hazardous material storage area.

Suppression of dislocations by Sb spray in the vicinity of InAs/GaAs quantum dots

PubMed Central

2014-01-01

The effect of Sb spray prior to the capping of a GaAs layer on the structure and properties of InAs/GaAs quantum dots (QDs) grown by molecular beam epitaxy (MBE) is studied by cross-sectional high-resolution transmission electron microscopy (HRTEM). Compared to the typical GaAs-capped InAs/GaAs QDs, Sb-sprayed QDs display a more uniform lens shape with a thickness of about 3 ~ 4 nm rather than the pyramidal shape of the non-Sb-sprayed QDs. Particularly, the dislocations were observed to be passivated in the InAs/GaAs interface region and even be suppressed to a large extent. There are almost no extended dislocations in the immediate vicinity of the QDs. This result is most likely related to the formation of graded GaAsSb immediately adjacent to the InAs QDs that provides strain relief for the dot/capping layer lattice mismatch. PACS 81.05.Ea; 81.07.-b; 81.07.Ta PMID:24948897

Experimental investigation of insolation-driven dust ejection from Mars' CO2 ice caps

NASA Astrophysics Data System (ADS)

Kaufmann, E.; Hagermann, A.

2017-01-01

Mars' polar caps are - depending on hemisphere and season - partially or totally covered with CO2 ice. Icy surfaces such as the polar caps of Mars behave differently from surfaces covered with rock and soil when they are irradiated by solar light. The latter absorb and reflect incoming solar radiation within a thin layer beneath the surface. In contrast, ices are partially transparent in the visible spectral range and opaque in the infrared. Due to this fact, the solar radiation can penetrate to a certain depth and raise the temperature of the ice or dust below the surface. This may play an important role in the energy balance of icy surfaces in the solar system, as already noted in previous investigations. We investigated the temperature profiles inside CO2 ice samples including a dust layer under Martian conditions. We have been able to trigger dust eruptions, but also demonstrated that these require a very narrow range of temperature and ambient pressure. We discuss possible implications for the understanding of phenomena such as arachneiform patterns or fan shaped deposits as observed in Mars' southern polar region.

XAFS atomistic insight of the oxygen gettering in Ti/HfO 2 based OxRRAM

NASA Astrophysics Data System (ADS)

Viennet, R.; Roussel, H.; Rapenne, L.; Deschanvres, J. L.; Renevier, H.; Jousseaume, V.; Jalaguier, E.; Proietti, M. G.

2018-05-01

Hafnia-based resistive memories technology has come to maturation and acceded to the market of nonvolatile memories. Nevertheless, the physical mechanisms involved in resistive switching are not yet fully understood and the numerous ab initio simulations studies have few many atomic-scale experimental counterparts. In this study we investigate the oxygen migration mechanism from an amorphous HfO2 layer to the Ti cap layer at a local scale before and after a thermal treatment. X-ray absorption spectroscopy at the Ti K edge and Hf LIII edge has been performed on samples as-deposited and annealed in Ar at 400 ∘C to mimic the back-end-of-line thermal budget (BEOL) of CMOS technology. The short-range Ti and Hf environments have been determined, showing that annealing promotes the migration of O from HfO2 to Ti, the amount of which is quantified. This provokes an expansion and an increase of atomic disorder in the Ti lattice. The nature of the oxygen gettering mechanism by the Ti metal is understood by comparing samples with increasing Ti-capping thickness. We show that the Ti getter effect has to be activated by thermal treatment and that the O diffusion takes place in a region of a few nanometers close to the Ti /HfO2 interface. Therefore, the thermal budget history and the Ti cap-layer thickness determine the oxygen vacancy content in the HfO2 layer, which in turn controls the electrical properties, especially the forming operation.

The Effects of Light Intensity, Casing Layers, and Layering Styles on Royal Sun Medicinal Mushroom, Agaricus brasiliensis (Higher Basidiomycetes) Cultivation in Turkey.

PubMed

Adanacioglu, Neşe; Boztok, Kaya; Akdeniz, Ramazan Cengiz

2015-01-01

The aim of this research is to evaluate the effects of light intensity, casing layers, and layering styles on the production of the culinary-medicinal mushroom Agaricus brasiliensis in Turkey. The experiments were designed in split-split plots and replicated twice. Three different light intensities-I1, 350 lux; I2, 450 lux; and I3, 750 lux-were used in main plots as environmental factors. A mixture of 4 different casing layers- peat (100%), peat-perlite (75%:25%), peat-clinoptilolite (75%:25%), and peat-perlite-clinoptilolite (60%:20%:20%)-were used at split plots and at split plots. S1, a flat, 3-cm casing layer; S2, a flat, 5-cm casing layer; and S3, casing soil ridges 10 cm wide × 4 cm high, 10 cm apart, were deposited on top of 1-cm overall soil casing layers. At the end of the harvest phase, the total yield was estimated per 100 kg of substrate. Biological efficiency (percentage) was determined from the fresh weight of the mushrooms and the dry weight of the compost at the end of the harvesting period. The highest total yield (7.2 kg/100 kg compost) and biological efficiency (27.63%) were achieved from I2 × peat-perlite-clinoptilolite × S2 treatment. Influence of light intensity, casing layer, layering style, and their interaction in treatments with color values (L*, a*, b*, chroma*, and hue*) also were examined. It has been shown that within color values, chroma* (saturation) values of mushroom caps were affected by light intensity, casing layer, and layering style treatments and light intensity × casing layer treatments and the brightness of mushroom caps tended to increase as light intensity increased.

The Semantics of the Spanish Conditional in Discourse.

ERIC Educational Resources Information Center

Lozano, Anthony G.

1988-01-01

Contrasts the hypothetical conditional or "modo potencial" in Spanish with the subsequence conditional. Passages from "El habla de la ciudad de Mexico" and from works by Carballido and Borges are cited as examples. Other grammatical studies of the Spanish conditional are reviewed. (LMO)

Antecedents and Consequences of Verbal Disagreements during Small-Group Learning.

ERIC Educational Resources Information Center

Lindow, Janet A.; And Others

1985-01-01

Controversy, an aspect of small-group interactions, was investigated in 10 mixed-ability, mixed-sex, elementary math groups through analysis of dissension episodes. Results showed that boys and higher-ability students had significantly more prevailing answers and demonstrations. (Author/LMO)

Distribution of the Determinant of the Sample Correlation Matrix: Monte Carlo Type One Error Rates.

ERIC Educational Resources Information Center

Reddon, John R.; And Others

1985-01-01

Computer sampling from a multivariate normal spherical population was used to evaluate the type one error rates for a test of sphericity based on the distribution of the determinant of the sample correlation matrix. (Author/LMO)

Cognitive Relativism in Evaluation.

ERIC Educational Resources Information Center

Alexander, H. A.

1986-01-01

A group of defenses of qualitative evaluation methods is examined, based on a hard relativistic interpretation of the work of Thomas Kuhn. A promising defense of qualitative evaluation may be found in a soft-relativist interpretation of Kuhn's analysis of the nature of scientific discovery. (Author/LMO)

Trying Out a New Dictionary.

ERIC Educational Resources Information Center

Benson, Morton; Benson, Evelyn

1988-01-01

Describes the BBI Combinatory Dictionary of English and demonstrates its usefulness for advanced learners of English by administering a monolingual completion test, first without a dictionary and then with the BBI, to Hungarian and Russian English teachers. Both groups' scores improved dramatically on the posttest. (LMO)

Method of making dense, conformal, ultra-thin cap layers for nanoporous low-k ILD by plasma assisted atomic layer deposition

DOEpatents

Jiang, Ying-Bing [Albuquerque, NM; Cecchi, Joseph L [Albuquerque, NM; Brinker, C Jeffrey [Albuquerque, NM

2011-05-24

Barrier layers and methods for forming barrier layers on a porous layer are provided. The methods can include chemically adsorbing a plurality of first molecules on a surface of the porous layer in a chamber and forming a first layer of the first molecules on the surface of the porous layer. A plasma can then be used to react a plurality of second molecules with the first layer of first molecules to form a first layer of a barrier layer. The barrier layers can seal the pores of the porous material, function as a diffusion barrier, be conformal, and/or have a negligible impact on the overall ILD k value of the porous material.

Shake table test of soil-pile groups-bridge structure interaction in liquefiable ground

NASA Astrophysics Data System (ADS)

Tang, Liang; Ling, Xianzhang; Xu, Pengju; Gao, Xia; Wang, Dongsheng

2010-03-01

This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground. The soil profile, contained in a large-scale laminar shear box, consisted of a horizontally saturated sand layer overlaid with a silty clay layer, with the simulated low-cap pile groups embedded. The container was excited in three El Centro earthquake events of different levels. Test results indicate that excessive pore pressure (EPP) during slight shaking only slightly accumulated, and the accumulation mainly occurred during strong shaking. The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased. The acceleration response of the sand was remarkably influenced by soil liquefaction. As soil liquefaction occurred, the peak sand displacement gradually lagged behind the input acceleration; meanwhile, the sand displacement exhibited an increasing effect on the bending moment of the pile, and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top. A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events. It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun.

Mars Secular Obliquity Change Due to Water Ice Caps

NASA Technical Reports Server (NTRS)

Rubincam, David P.

1998-01-01

Mars may have substantially changed its average axial tilt over geologic time due to the waxing and waning of water ice caps. Depending upon Mars' climate and internal structure, the average obliquity could have increased or decreased through climate friction by tens of degrees. A decrease could account for the apparent youthfulness of the polar layered terrain. Alternatively, Mars' average obliquity may have changed until it became "stuck" at its present value of 24.4 deg.

Creating and maintaining a gas cap in tar sands formations

DOEpatents

Vinegar, Harold J.; Karanikas, John Michael; Dinkoruk, Deniz Sumnu; Wellington, Scott Lee

2010-03-16

Methods for treating a tar sands formation are disclosed herein. Methods for treating a tar sands formation may include providing heat to at least part of a hydrocarbon layer in the formation from one or more heaters located in the formation. Pressure may be allowed to increase in an upper portion of the formation to provide a gas cap in the upper portion. At least some hydrocarbons are produced from a lower portion of the formation.

Observations of the Early Morning Boundary-Layer Transition with Small Remotely-Piloted Aircraft

NASA Astrophysics Data System (ADS)

Wildmann, Norman; Rau, Gerrit Anke; Bange, Jens

2015-12-01

A remotely-piloted aircraft (RPA), equipped with a high resolution thermodynamic sensor package, was used to investigate physical processes during the morning transition of the atmospheric boundary layer over land. Experiments were conducted at a test site in heterogeneous terrain in south-west Germany on 5 days from June to September 2013 in an evolving shallow convective boundary layer, which then developed into a well-mixed layer later in the day. A combination of vertical profiling and constant-altitude profiling (CAP) at 100 m height above ground level was chosen as the measuring strategy throughout the experiment. The combination of flight strategies allows the application of mixed-layer scaling using the boundary-layer height z_i, convective velocity scale w_* and convective temperature scale θ _*. The hypothesis that mixed-layer theory is valid during the whole transition was not confirmed for all parameters. A good agreement is found for temperature variances, especially in the upper half of the boundary layer, and the normalized heat-flux profile. The results were compared to a previous study with the helicopter-borne turbulence probe Helipod, and it was found that similar data quality can be achieved with the RPA. On all days, the CAP flight level was within the entrainment zone for a short time, and the horizontal variability of temperature and water vapour along the flight path is presented as an example of the inhomogeneity of layer interfaces in the boundary layer. The study serves as a case study of the possibilities and limitations with state-of-the-art RPA technology in micrometeorology.

Electron Beam-Induced Deposition for Atom Probe Tomography Specimen Capping Layers.

PubMed

Diercks, David R; Gorman, Brian P; Mulders, Johannes J L

2017-04-01

Six precursors were evaluated for use as in situ electron beam-induced deposition capping layers in the preparation of atom probe tomography specimens with a focus on near-surface features where some of the deposition is retained at the specimen apex. Specimens were prepared by deposition of each precursor onto silicon posts and shaped into sub-70-nm radii needles using a focused ion beam. The utility of the depositions was assessed using several criteria including composition and uniformity, evaporation behavior and evaporation fields, and depth of Ga+ ion penetration. Atom probe analyses through depositions of methyl cyclopentadienyl platinum trimethyl, palladium hexafluoroacetylacetonate, and dimethyl-gold-acetylacetonate [Me2Au(acac)] were all found to result in tip fracture at voltages exceeding 3 kV. Examination of the deposition using Me2Au(acac) plus flowing O2 was inconclusive due to evaporation of surface silicon from below the deposition under all analysis conditions. Dicobalt octacarbonyl [Co2(CO)8] and diiron nonacarbonyl [Fe2(CO)9] depositions were found to be effective as in situ capping materials for the silicon specimens. Their very different evaporation fields [36 V/nm for Co2(CO)8 and 21 V/nm for Fe2(CO)9] provide options for achieving reasonably close matching of the evaporation field between the capping material and many materials of interest.

Enhanced biocorrosion resistance and biocompatibility of degradable Mg-Nd-Zn-Zr alloy by brushite coating.

PubMed

Niu, Jialin; Yuan, Guangyin; Liao, Yi; Mao, Lin; Zhang, Jian; Wang, Yongping; Huang, Feng; Jiang, Yao; He, Yaohua; Ding, Wenjiang

2013-12-01

To further improve the corrosion resistance and biocompatibility of Mg-Nd-Zn-Zr alloy (JDBM), a biodegradable calcium phosphate coating (Ca-P coating) with high bonding strength was developed using a novel chemical deposition method. The main composition of the Ca-P coating was brushite (CaHPO4·2H2O). The bonding strength between the coating and the JDBM substrate was measured to be over 10 MPa, and the thickness of the coating layer was about 10-30 μm. The in vitro corrosion tests indicated that the Ca-P treatment improved the corrosion resistance of JDBM alloy in Hank's solution. Ca-P treatment significantly reduced the hemolysis rate of JDBM alloy from 48% to 0.68%, and induced no toxicity to MC3T3-E1 cells. The in vivo implantation experiment in New Zealand's rabbit tibia showed that the degradation rate was reduced obviously by the Ca-P treatment and less gas was produced from Ca-P treated JDBM bone plates and screws in early stage of the implantation, and at least 10weeks degradation time can be prolonged by the present coating techniques. Both Ca-P treated and untreated JDBM Mg alloy induced bone growth. The primary results indicate that the present Ca-P treatment is a promising technique for the degradable Mg-based biomaterials for orthopedic applications. © 2013.

The mechanism of RNA 5' capping with NAD +, NADH and desphospho-CoA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bird, Jeremy G.; Zhang, Yu; Tian, Yuan

The chemical nature of the 5' end of RNA is a key determinant of RNA stability, processing, localization and translation efficiency and has been proposed to provide a layer of ‘epitranscriptomic’ gene regulation. Recently it has been shown that some bacterial RNA species carry a 5'-end structure reminiscent of the 5' 7-methylguanylate ‘cap’ in eukaryotic RNA. In particular, RNA species containing a 5'-end nicotinamide adenine dinucleotide (NAD+) or 3'-desphospho-coenzyme A (dpCoA) have been identified in both Gram-negative and Gram-positive bacteria. It has been proposed that NAD+, reduced NAD+ (NADH) and dpCoA caps are added to RNA after transcription initiation, inmore » a manner analogous to the addition of 7-methylguanylate caps. Here we show instead that NAD+, NADH and dpCoA are incorporated into RNA during transcription initiation, by serving as non-canonical initiating nucleotides (NCINs) for de novo transcription initiation by cellular RNA polymerase (RNAP). We further show that both bacterial RNAP and eukaryotic RNAP II incorporate NCIN caps, that promoter DNA sequences at and upstream of the transcription start site determine the efficiency of NCIN capping, that NCIN capping occurs in vivo, and that NCIN capping has functional consequences. We report crystal structures of transcription initiation complexes containing NCIN-capped RNA products. Our results define the mechanism and structural basis of NCIN capping, and suggest that NCIN-mediated ‘ab initio capping’ may occur in all organisms.« less

Lunar Magma Ocean Crystallization: Constraints from Fractional Crystallization Experiments

NASA Technical Reports Server (NTRS)

Rapp, J. F.; Draper, D. S.

2015-01-01

The currently accepted paradigm of lunar formation is that of accretion from the ejecta of a giant impact, followed by crystallization of a global scale magma ocean. This model accounts for the formation of the anorthosite highlands crust, which is globally distributed and old, and the formation of the younger mare basalts which are derived from a source region that has experienced plagioclase extraction. Several attempts at modelling the crystallization of such a lunar magma ocean (LMO) have been made, but our ever-increasing knowledge of the lunar samples and surface have raised as many questions as these models have answered. Geodynamic models of lunar accretion suggest that shortly following accretion the bulk of the lunar mass was hot, likely at least above the solidus]. Models of LMO crystallization that assume a deep magma ocean are therefore geodynamically favorable, but they have been difficult to reconcile with a thick plagioclase-rich crust. A refractory element enriched bulk composition, a shallow magma ocean, or a combination of the two have been suggested as a way to produce enough plagioclase to account for the assumed thickness of the crust. Recently however, geophysical data from the GRAIL mission have indicated that the lunar anorthositic crust is not as thick as was initially estimated, which allows for both a deeper magma ocean and a bulk composition more similar to the terrestrial upper mantle. We report on experimental simulations of the fractional crystallization of a deep (approximately 100km) LMO with a terrestrial upper mantle-like (LPUM) bulk composition. Our experimental results will help to define the composition of the lunar crust and mantle cumulates, and allow us to consider important questions such as source regions of the mare basalts and Mg-suite, the role of mantle overturn after magma ocean crystallization and the nature of KREEP

Sm-Nd and Ar-Ar Studies of DHO 908 and 489: Implications for Lunar Crustal History

NASA Technical Reports Server (NTRS)

Nyquist, L. E.; Shih, C. Y.; Reese, Y. D.; Park, J.; Bogard, D. D.; Garrison, D. H.; Yamaguchi, A.

2011-01-01

It is widely assumed that ferroan anorthosites (FANs) formed as flotation cumulates on a global lunar magma ocean (LMO). A corollary is that all FANs are approximately contemporaneous and formed with the same initial Nd-143/Nd-144 ratio. Indeed, a whole rock isochron for selected FANs (and An93 anorthosite) yields an isochron age of 4.42 +/- 0.13 Ga and initial Nd-143/Nd-144, expressed in epsilon-units, of epsilon(sub Nd,CHUR) = 0.3+/-0.3 relative to the CHondritic Uniform Reservoir , or epsilon(sub Nd,HEDPB)=-0.6+/-0.3 relative to the HED Parent Body. These values are in good agreement with the age (T) = 4.47+/-0.07 Ga, and epsilon(sub Nd,HEDPB) =-0.6 +/- 0.5 for FAN 67075. We also have studied anorthositic clasts in the Dhofar 908 and 489 lunar highland meteorites containing clasts of magnesian anorthosites (MAN) with Mg# approximately 75. Because of their relatively high Mg#, magnesian anorthosites should have preceded most FANs in crystallization from the LMO if both are LMO products. Thus, it is important to determine whether the Nd-isotopic data of MAN and FAN are consistent with a co-magmatic origin. We previously reported Sm-Nd data for white clast Dho 908 WC. Mafic minerals in this clast were too small to be physically separated for an isochron. However, we estimated initial Nd-143/Nd-144 for the clast by combining its bulk ("whole rock") Sm-Nd data with an Ar-39-Ar-40 age of 4.42+/-.04 Ga. Here we report additional Sm-Nd data for bulk samples of Dho 908 and its pair Dho 489.

The Chlorine Isotopic Composition Of Lunar UrKREEP

NASA Technical Reports Server (NTRS)

Barnes, J. J.; Tartese, R.; Anand, M.; McCubbin, F. M.; Neal, C. R.; Franchi, I. A.

2016-01-01

Since the long standing paradigm of an anhydrous Moon was challenged there has been a renewed focus on investigating volatiles in a variety of lunar samples. Numerous studies have examined the abundances and isotopic compositions of volatiles in lunar apatite, Ca5(PO4)3(F,Cl,OH). In particular, apatite has been used as a tool for assessing the sources of H2O in the lunar interior. However, current models for the Moon's formation have yet to fully account for its thermal evolution in the presence of H2O and other volatiles. For ex-ample, in the context of the lunar magma ocean (LMO) model, it is anticipated that chlorine (and other volatiles) should have been concentrated in the late-stage LMO residual melts (i.e., the dregs enriched in incompatible elements such as K, REEs (Rare Earth Elements), and P, collectively called KREEP, and in its primitive form - urKREEP, given its incompatibility in mafic minerals like olivine and pyroxene, which were the dominant phases that crystallized early in the cumulate pile of the LMO. When compared to chondritic meteorites and terrestrial rocks, lunar samples have exotic chlorine isotope compositions, which are difficult to explain in light of the abundance and isotopic composition of other volatile species, especially H, and the current estimates for chlorine and H2O in the bulk silicate Moon (BSM). In order to better understand the processes involved in giving rise to the heavy chlorine isotope compositions of lunar samples, we have performed a comprehensive in situ high precision study of chlorine isotopes in lunar apatite from a suite of Apollo samples covering a range of geochemical characteristics and petrologic types.

Prognostic significance of immunohistochemistry-based markers and algorithms in immunochemotherapy-treated diffuse large B cell lymphoma patients.

PubMed

Culpin, Rachel E; Sieniawski, Michal; Angus, Brian; Menon, Geetha K; Proctor, Stephen J; Milne, Paul; McCabe, Kate; Mainou-Fowler, Tryfonia

2013-12-01

To reassess the prognostic validity of immunohistochemical markers and algorithms identified in the CHOP era in immunochemotherapy-treated diffuse large B cell lymphoma patients. The prognostic significance of immunohistochemical markers (CD10, Bcl-6, Bcl-2, MUM1, Ki-67, CD5, GCET1, FoxP1, LMO2) and algorithms (Hans, Hans*, Muris, Choi, Choi*, Nyman, Visco-Young, Tally) was assessed using clinical diagnostic blocks taken from an unselected, population-based cohort of 190 patients treated with R-CHOP. Dichotomizing expression, low CD10 (<10%), low LMO2 (<70%) or high Bcl-2 (≥80%) predicted shorter overall survival (OS; P = 0.033, P = 0.010 and P = 0.008, respectively). High Bcl-2 (≥80%), low Bcl-6 (<60%), low GCET1 (<20%) or low LMO2 (<70%) predicted shorter progression-free survival (PFS; P = 0.001, P = 0.048, P = 0.045 and P = 0.002, respectively). The Hans, Hans* and Muris classifiers predicted OS (P = 0.022, P = 0.037 and P = 0.011) and PFS (P = 0.021, P = 0.020 and P = 0.004). The Choi, Choi* and Tally were associated with PFS (P = 0.049, P = 0.009 and P = 0.023). In multivariate analysis, the International Prognostic Index (IPI) was the only independent predictor of outcome (OS; HR: 2.60, P < 0.001 and PFS; HR: 2.91, P < 0.001). Results highlight the controversy surrounding immunohistochemistry-based algorithms in the R-CHOP era. The need for more robust markers, applicable to the clinic, for incorporation into improved prognostic systems is emphasized. © 2013 John Wiley & Sons Ltd.

Contribution of Three Bile-Associated Loci, bsh, pva, and btlB, to Gastrointestinal Persistence and Bile Tolerance of Listeria monocytogenes

PubMed Central

Begley, Máire; Sleator, Roy D.; Gahan, Cormac G. M.; Hill, Colin

2005-01-01

Listeria monocytogenes must resist the deleterious actions of bile in order to infect and subsequently colonize the human gastrointestinal tract. The molecular mechanisms used by the bacterium to resist bile and the influence of bile on pathogenesis are as yet largely unexplored. This study describes the analysis of three genes—bsh, pva, and btlB—previously annotated as bile-associated loci in the sequenced L. monocytogenes EGDe genome (lmo2067, lmo0446, and lmo0754, respectively). Analysis of deletion mutants revealed a role for all three genes in resisting the acute toxicity of bile and bile salts, particularly glycoconjugated bile salts at low pH. Mutants were unaffected in the other stress responses examined (acid, salt, and detergents). Bile hydrolysis assays demonstrate that L. monocytogenes possesses only one bile salt hydrolase gene, namely, bsh. Transcriptional analyses and activity assays revealed that, although it is regulated by both PrfA and σB, the latter appears to play the greater role in modulating bsh expression. In addition to being incapable of bile hydrolysis, a sigB mutant was shown to be exquisitely sensitive to bile salts. Furthermore, increased expression of sigB was detected under anaerobic conditions and during murine infection. A gene previously annotated as a possible penicillin V amidase (pva) or bile salt hydrolase was shown to be required for resistance to penicillin V but not penicillin G but did not demonstrate a role in bile hydrolysis. Finally, animal (murine) studies revealed an important role for both bsh and btlB in the intestinal persistence of L. monocytogenes. PMID:15664931

Antiferroelectricity in lanthanum doped zirconia without metallic capping layers and post-deposition/-metallization anneals

NASA Astrophysics Data System (ADS)

Wang, Zheng; Gaskell, Anthony Arthur; Dopita, Milan; Kriegner, Dominik; Tasneem, Nujhat; Mack, Jerry; Mukherjee, Niloy; Karim, Zia; Khan, Asif Islam

2018-05-01

We report the effects of lanthanum doping/alloying on antiferroelectric (AFE) properties of ZrO2. Starting with pure ZrO2, an increase in La doping leads to the narrowing of the AFE double hysteresis loops and an increase in the critical voltage/electric field for AFE → ferroelectric transition. At higher La contents, the polarization-voltage characteristics of doped/alloyed ZrO2 resemble that of a non-linear dielectric without any discernible AFE-type hysteresis. X-ray diffraction based analysis indicates that the increased La content while preserving the non-polar, parent AFE, tetragonal P42/nmc phase leads to a decrease in tetragonality and the (nano-)crystallite size and an increase in the unit cell volume. Furthermore, antiferroelectric behavior is obtained in the as-deposited thin films without requiring any capping metallic layers and post-deposition/-metallization anneals due to which our specific atomic layer deposition system configuration crystallizes and stabilizes the AFE tetragonal phase during growth.

Nanoscale electro-structural characterisation of ohmic contacts formed on p-type implanted 4H-SiC

NASA Astrophysics Data System (ADS)

Frazzetto, Alessia; Giannazzo, Filippo; Lo Nigro, Raffaella; di Franco, Salvatore; Bongiorno, Corrado; Saggio, Mario; Zanetti, Edoardo; Raineri, Vito; Roccaforte, Fabrizio

2011-12-01

This work reports a nanoscale electro-structural characterisation of Ti/Al ohmic contacts formed on p-type Al-implanted silicon carbide (4H-SiC). The morphological and the electrical properties of the Al-implanted layer, annealed at 1700°C with or without a protective capping layer, and of the ohmic contacts were studied using atomic force microscopy [AFM], transmission line model measurements and local current measurements performed with conductive AFM. The characteristics of the contacts were significantly affected by the roughness of the underlying SiC. In particular, the surface roughness of the Al-implanted SiC regions annealed at 1700°C could be strongly reduced using a protective carbon capping layer during annealing. This latter resulted in an improved surface morphology and specific contact resistance of the Ti/Al ohmic contacts formed on these regions. The microstructure of the contacts was monitored by X-ray diffraction analysis and a cross-sectional transmission electron microscopy, and correlated with the electrical results.

GaAs droplet quantum dots with nanometer-thin capping layer for plasmonic applications.

PubMed

Park, Suk In; Trojak, Oliver Joe; Lee, Eunhye; Song, Jin Dong; Kyhm, Jihoon; Han, Ilki; Kim, Jongsu; Yi, Gyu-Chul; Sapienza, Luca

2018-05-18

We report on the growth and optical characterization of droplet GaAs quantum dots (QDs) with extremely-thin (11 nm) capping layers. To achieve such result, an internal thermal heating step is introduced during the growth and its role in the morphological properties of the QDs obtained is investigated via scanning electron and atomic force microscopy. Photoluminescence measurements at cryogenic temperatures show optically stable, sharp and bright emission from single QDs, at visible wavelengths. Given the quality of their optical properties and the proximity to the surface, such emitters are good candidates for the investigation of near field effects, like the coupling to plasmonic modes, in order to strongly control the directionality of the emission and/or the spontaneous emission rate, crucial parameters for quantum photonic applications.

GaAs droplet quantum dots with nanometer-thin capping layer for plasmonic applications

NASA Astrophysics Data System (ADS)

In Park, Suk; Trojak, Oliver Joe; Lee, Eunhye; Song, Jin Dong; Kyhm, Jihoon; Han, Ilki; Kim, Jongsu; Yi, Gyu-Chul; Sapienza, Luca

2018-05-01

We report on the growth and optical characterization of droplet GaAs quantum dots (QDs) with extremely-thin (11 nm) capping layers. To achieve such result, an internal thermal heating step is introduced during the growth and its role in the morphological properties of the QDs obtained is investigated via scanning electron and atomic force microscopy. Photoluminescence measurements at cryogenic temperatures show optically stable, sharp and bright emission from single QDs, at visible wavelengths. Given the quality of their optical properties and the proximity to the surface, such emitters are good candidates for the investigation of near field effects, like the coupling to plasmonic modes, in order to strongly control the directionality of the emission and/or the spontaneous emission rate, crucial parameters for quantum photonic applications.

Optimal doping control of magnetic semiconductors via subsurfactant epitaxy.

PubMed

Zeng, Changgan; Zhang, Zhenyu; van Benthem, Klaus; Chisholm, Matthew F; Weitering, Hanno H

2008-02-15

"Subsurfactant epitaxy" is established as a conceptually new approach for introducing manganese as a magnetic dopant into germanium. A kinetic pathway is devised in which the subsurface interstitial sites on Ge(100) are first selectively populated with Mn, while lateral diffusion and clustering on or underneath the surface are effectively suppressed. Subsequent Ge deposition as a capping layer produces a novel surfactantlike phenomenon as the interstitial Mn atoms float towards newly defined subsurface sites at the growth front. Furthermore, the Mn atoms that failed to float upwards are uniformly distributed within the Ge capping layer. The resulting doping levels of order 0.25 at. % would normally be considered too low for ferromagnetic ordering, but the Curie temperature exceeds room temperature by a comfortable margin. Subsurfactant epitaxy thus enables superior dopant control in magnetic semiconductors.

Science goals for a Mars Polar Cap subsurface mission : optical approaches for investiagations of inclusions in ice

NASA Technical Reports Server (NTRS)

Mogensen, Claus T.; Carsey, Frank D.; Behar, Alberto; Engelhardt, Hermann; Lane, Arthur L.

2002-01-01

The Mars Polar Caps are highly interesting features of Mars and have received much recent attention with new and exciting data on morphology, basal units, and layered outcroppings. We have examined the climatological, glaciological, and geological issues associated with a subsurface exploration of the Mars North Polar Cap and have determined that a finescale optical examination of ice in a borehole, to examine the stratigraphy, geochemistry and geochronology of the ice, is feasible. This information will enable reconstruction of the development of the cap as well as predication of the properties of its ice. We present visible imagery taken of dust inclusions in archived Greenland ice cores as well as in-situ images of accreted lithologic inclusions in West Antarctica, and we argue for use of this kind of data in Mars climate reconstruction as has been successful with Greenland and Antarctic ice core anlaysis.

Science goals for a Mars Polar Cap subsurface mission : optical approaches for investigations of inclusions in ice

NASA Technical Reports Server (NTRS)

Carsey, Frank; Mogensen, Claus T.; Behar, Alberto; Engelhardt, Hermann; Lane, Arthur L.

2002-01-01

The Mars Polar Caps are highly interesting features of Mars and have received much recent attention with new and exciting data on morphology, basal units, and layered outcroppings. We have examined the climatological, glaciological, and geological issues associated with a subsurface exploration of the Mars North Polar Cap and have determined that a finescale optical examination of ice in a borehole, to examine the stratigraphy, geochemistry and geochronology of the ice, is feasible. This information will enable reconstruction of the development of the cap as well as prediction of the properties of its ice. We present visible imagery taken of dust inclusions in archived Greenland ice cores as well as in-situ images of accreted lithologic inclusions in West Antarctica, and we argue for use of this kind of data in Mars climate reconstruction as has been successful with Greenland and Antarctic ice core analysis. .

Factor Structure of the MCAT and Pilot Essay.

ERIC Educational Resources Information Center

Mitchell, Karen J.; Molidor, John B.

1986-01-01

Research reported in this paper considered the construct validity of a trial essay administered in 1985-87 Medical College Admission Test (MCAT). The addition of the essay caused the non-science factor observed in previous MCAT research to be more strongly defined. (Author/LMO)

Lotus 123 as a Gradebook: A Means of Increasing Teacher Productivity.

ERIC Educational Resources Information Center

Smith, Karen L.

1988-01-01

Examines the application of the spreadsheet program Lotus 1-2-3 to design a computerized gradebook that saves time in assessing students' strengths and weaknesses in a proficiency-oriented foreign language classroom. Sample entries are shown in text and Appendices. (Author/LMO)

Social Orientation and the Social Self-Esteem of Gifted and Talented Female Adolescents.

ERIC Educational Resources Information Center

Hollinger, Constance L.; Fleming, Elyse S.

1985-01-01

The present study tests the applicability of Carlson's theory for a sample of gifted and talented female adolescents by examining three dimensions of possible self-esteem antecedents: actual talent ratings, self-perceptions of talent, and personality attributes. (Author/LMO)

Atomically resolved calcium phosphate coating on a gold substrate.

PubMed

Metoki, Noah; Baik, Sung-Il; Isheim, Dieter; Mandler, Daniel; Seidman, David N; Eliaz, Noam

2018-05-10

Some articles have revealed that the electrodeposition of calcium phosphate (CaP) coatings entails a precursor phase, similarly to biomineralization in vivo. The chemical composition of the initial layer and its thickness are, however, still arguable, to the best of our knowledge. Moreover, while CaP and electrodeposition of metal coatings have been studied utilizing atom-probe tomography (APT), the electrodeposition of CaP ceramics has not been heretofore studied. Herein, we present an investigation of the CaP deposition on a gold substrate. Using APT and transmission electron microscopy (TEM) it is found that a mixture of phases, which could serve as transient precursor phases to hydroxyapatite (HAp), can be detected. The thickness of these phases is tens of nanometers, and they consist of amorphous CaP (ACP), dibasic calcium phosphate dihydrate (DCPD), and octacalcium phosphate (OCP). This demonstrates the value of using atomic-resolved characterization techniques for identifying the precursor phases. It also indicates that the kinetics of their transformation into the more stable HAp is not too fast to enable their observation. The coating gradually displays higher Ca/P atomic ratios, a porous nature, and concomitantly a change in its density.

IR spectral properties of dust and ice at the Mars south polar cap

NASA Astrophysics Data System (ADS)

Titus, T. N.; Kieffer, H. H.

2001-11-01

Removal of atmospheric dust effects is required to derive surface IR spectral emissivity. Commonly, the atmospheric-surface separation is based on radiative transfer (RT) spectral inversion methods using nadir-pointing observations. This methodology depends on a priori knowledge of the spectral shape of each atmospheric aerosol (e.g. dust or water ice) and a large thermal contrast between the surface and atmosphere. RT methods fail over the polar caps due to low thermal contrast between the atmosphere and the surface. We have used multi-angle Emission Phase Function (EPF) observations to estimate the opacity spectrum of dust over the springtime south polar cap and the underlying surface radiance, and thus, the surface emissivity. We include a few EPFs from Hellas Basin as a basis for comparisons between the spectral shape of polar and non-polar dust. Surface spectral emissivities over the seasonal cap are compared to CO2 models. Our results show that the spectral shape of the polar dust opacity is not constant, but is a two-parameter family that can be characterized by the 9 um and 20 um opacities. The 9 um opacity varies from 0.15 to 0.45 and characterizes the overall atmospheric conditions. The 9 um to 20 um opacity ratio varies from 2.0 to 5.1, suggesting changes in dust size distribution over the polar caps. Derived surface temperatures from the EPFs confirm that the slightly elevated temperatures (relative to CO2 frost temperature) observed in ``cryptic'' regions are a surface effect, not atmospheric. Comparison of broad-band reflectivity and surface emissivities to model spectra suggest the bright regions (e.g. perennial cap, Mountains of Mitchell) have higher albedos due to a thin surface layer of fine-grain CO2 (perhaps either frost or fractured ice) with an underlying layer of either coarse grain or slab CO2 ice.

Engineering of electric field distribution in GaN(cap)/AlGaN/GaN heterostructures: theoretical and experimental studies

NASA Astrophysics Data System (ADS)

Gladysiewicz, M.; Janicki, L.; Misiewicz, J.; Sobanska, M.; Klosek, K.; Zytkiewicz, Z. R.; Kudrawiec, R.

2016-09-01

Polarization engineering of GaN-based heterostructures opens a way to develop advanced transistor heterostructures, although measurement of the electric field in such heterostructures is not a simple task. In this work, contactless electroreflectance (CER) spectroscopy has been applied to measure the electric field in GaN-based heterostructures. For a set of GaN(d  =  0, 5, 15, and 30 nm)/AlGaN(20 nm)/GaN(buffer) heterostructures a decrease of electric field in the GaN(cap) layer from 0.66 MV cm-1 to 0.27 MV cm-1 and an increase of the electric field in the AlGaN layer from 0.57 MV cm-1 to 0.99 MV cm-1 have been observed with the increase in the GaN(cap) thickness from 5-30 nm. For a set of GaN(20 nm)/AlGaN(d  =  10, 20, 30, and 40 nm)/GaN(buffer) heterostructures a decrease of the electric field in the AlGaN layer from 1.77 MV cm-1 to 0.64 MV cm-1 and an increase of the electric field in the GaN layer from 0.57 MV cm-1 to 0.99 MV cm-1 were observed with the increase in the AlGaN thickness from 10-40 nm. To determine the distribution of the electric field in these heterostructures the Schrödinger and Poisson equations are solved in a self-consistent manner and matched with experimental data. It is shown that the built-in electric field in the GaN(cap) and AlGaN layers obtained from measurements does not reach values of electric field resulting only from polarization effects. The measured electric fields are smaller due to a screening of polarization effects by free carriers, which are inhomogeneously distributed across the heterostructure and accumulate at interfaces. The results clearly demonstrate that CER measurements supported by theoretical calculations are able to determine the electric field distribution in GaN-based heterostructures quantitatively, which is very important for polarization engineering in this material system.

Heat treatment of bulk gallium arsenide using a phosphosilicate glass cap

NASA Technical Reports Server (NTRS)

Mathur, G.; Wheaton, M. L.; Borrego, J. M.; Ghandhi, S. K.

1985-01-01

n-type bulk GaAs crystals, capped with chemically vapor-deposited phosphosilicate glass, were heat treated at temperatures in the range of 600 to 950 C. Measurements on Schottky diodes and solar cells fabricated on the heat-treated material, after removal of a damaged surface layer, show an increase in free-carrier concentration, in minority-carrier-diffusion length, and in solar-cell short-circuit current. The observed changes are attributed to a removal of lifetime-reducing acceptorlike impurities, defects, or their complexes.

Exposure of Water Ice in the Northern Mid-lattitudes of Mars

NASA Technical Reports Server (NTRS)

Allen, Carlton C.; Kanner, Lisa C.

2007-01-01

Water ice is exposed in the martian north polar cap, and is occasionally exposed beyond the cap boundary. Orbital gamma ray spectrometry data strongly imply the presence of water ice within meters of the surface at latitudes north of approximately 60 deg. We have examined midlatitude areas of the northern plains displaying evidence of residual ice-rich layers, and report possible present-day exposures of ice. These exposures, if confirmed, could constrain the latitudinal and temporal stability of surface ice on Mars.

Electrochemical characteristics of calcium-phosphatized AZ31 magnesium alloy in 0.9 % NaCl solution.

PubMed

Hadzima, Branislav; Mhaede, Mansour; Pastorek, Filip

2014-05-01

Magnesium alloys suffer from their high reactivity in common environments. Protective layers are widely created on the surface of magnesium alloys to improve their corrosion resistance. This article evaluates the influence of a calcium-phosphate layer on the electrochemical characteristics of AZ31 magnesium alloy in 0.9 % NaCl solution. The calcium phosphate (CaP) layer was electrochemically deposited in a solution containing 0.1 M Ca(NO3)2, 0.06 M NH4H2PO4 and 10 ml l(-1) of H2O2. The formed surface layer was composed mainly of brushite [(dicalcium phosphate dihidrate (DCPD)] as proved by energy-dispersive X-ray analysis. The surface morphology was observed by scanning electron microscopy. Immersion test was performed in order to observe degradation of the calcium phosphatized surfaces. The influence of the phosphate layer on the electrochemical characteristics of AZ31, in 0.9 % NaCl solution, was evaluated by potentiodynamic measurements and electrochemical impedance spectroscopy. The obtained results were analysed by the Tafel-extrapolation method and equivalent circuits method. The results showed that the polarization resistance of the DCPD-coated surface is about 25 times higher than that of non-coated surface. The CaP electro-deposition process increased the activation energy of corrosion process.

Exchange coupled CoPt/FePtC media for heat assisted magnetic recording

NASA Astrophysics Data System (ADS)

Dutta, Tanmay; Piramanayagam, S. N.; Ru, Tan Hui; Saifullah, M. S. M.; Bhatia, C. S.; Yang, Hyunsoo

2018-04-01

L10 FePtC granular media are being studied as potential future magnetic recording media and are set to be used in conjunction with heat assisted magnetic recording (HAMR) to enable recording at write fields within the range of current day recording heads. Media structures based on a FePtC storage layer and a capping layer can alleviate the switching field distribution (SFD) requirements of HAMR and reduce the noise originating from the writing process. However, the current designs suffer from SFD issues due to high temperature writing. To overcome this problem, we study a CoPt/FePtC exchange coupled composite structure, where FePtC serves as the storage layer and CoPt (with higher Curie temperature, Tc) as the capping layer. CoPt remains ferromagnetic at near Tc of FePtC. Consequently, the counter exchange energy from CoPt would reduce the noise resulting from the adjacent grain interactions during the writing process. CoPt/FePtC bilayer samples with different thicknesses of CoPt were investigated. Our studies found that CoPt forms a continuous layer at a thickness of 6 nm and leads to considerable reduction in the saturation field and its distribution.

High-Efficiency Silicon/Organic Heterojunction Solar Cells with Improved Junction Quality and Interface Passivation.

PubMed

He, Jian; Gao, Pingqi; Ling, Zhaoheng; Ding, Li; Yang, Zhenhai; Ye, Jichun; Cui, Yi

2016-12-27

Silicon/organic heterojunction solar cells (HSCs) based on conjugated polymers, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), and n-type silicon (n-Si) have attracted wide attention due to their potential advantages of high efficiency and low cost. However, the state-of-the-art efficiencies are still far from satisfactory due to the inferior junction quality. Here, facile treatments were applied by pretreating the n-Si wafer in tetramethylammonium hydroxide (TMAH) solution and using a capping copper iodide (CuI) layer on the PEDOT:PSS layer to achieve a high-quality Schottky junction. Detailed photoelectric characteristics indicated that the surface recombination was greatly suppressed after TMAH pretreatment, which increased the thickness of the interfacial oxide layer. Furthermore, the CuI capping layer induced a strong inversion layer near the n-Si surface, resulting in an excellent field effect passivation. With the collaborative improvements in the interface chemical and electrical passivation, a competitive open-circuit voltage of 0.656 V and a high fill factor of 78.1% were achieved, leading to a stable efficiency of over 14.3% for the planar n-Si/PEDOT:PSS HSCs. Our findings suggest promising strategies to further exploit the full voltage as well as efficiency potentials for Si/organic solar cells.

South Polar Cap Erosion and Aprons

NASA Technical Reports Server (NTRS)

2000-01-01

This scene is illuminated by sunlight from the upper left.

While Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) images have shown that the north and south polar cap surfaces are very different from each other, one thing that the two have in common is that they both seem to have been eroded. Erosion in the north appears mostly to come in the form of pits from which ice probably sublimed to vapor and was transported away from the polar cap by wind. Erosion in the south takes on a wider range of possible processes that include collapse, slumping and mass-movement on slopes, and probably sublimation. Among the landforms created by these process on the south polar cap are the 'aprons' that surround mesas and buttes of remnant layers such as the two almost triangular features in the lower quarter of this image. The upper slopes of the two triangular features show a stair-stepped pattern that suggest these hills are layered.

This image shows part of the south polar residual cap near 86.9oS, 78.5oW, and covers an area approximately 1.2 by 1.0 kilometers (0.7 x 0.6 miles) in size. The image has a resolution of 2.2 meters per pixel. The picture was taken on September 11, 1999.

Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

Classroom Use of Videogames.

ERIC Educational Resources Information Center

Silvern, Steven B.

1986-01-01

Video games may allow educators to reach children who have never before been incorporated into an educational experience within the confines of school. A distinction is made between types of arcade style games and educational games in Piagetian terms: practice games, symbolic games, games with rules, and games of construction. (LMO)

Family Life Education for Young Inner-City Teens: Identifying Needs.

ERIC Educational Resources Information Center

Herz, Elicia J.; Reis, Janet S.

1987-01-01

Sexual decision making, perceptions of responsibility for birth control and pregnancy, and knowledge of contraception and the consequences of teenage pregnancy were assessed among 251 high-risk seventh- and eighth-grade Black, inner-city adolescents to determine these young peoples' need for information. (Author/LMO)

Attention Gating in Short-Term Visual Memory.

ERIC Educational Resources Information Center

Reeves, Adam; Sperling, George

1986-01-01

An experiment is conducted showing that an attention shift to a stream of numerals presented in rapid serial visual presentation mode produces not a total loss, but a systematic distortion of order. An attention gating model (AGM) is developed from a more general attention model. (Author/LMO)

Artificial Intelligence: Applications in Education.

ERIC Educational Resources Information Center

Thorkildsen, Ron J.; And Others

1986-01-01

Artificial intelligence techniques are used in computer programs to search out rapidly and retrieve information from very large databases. Programing advances have also led to the development of systems that provide expert consultation (expert systems). These systems, as applied to education, are the primary emphasis of this article. (LMO)

Stress Patterns in High-Frequency Russian Nouns and Verbs.

ERIC Educational Resources Information Center

Cubberley, Paul

1987-01-01

Analyses for stress patterns of the first 1,000 nouns and 500 verbs from a high-frequency Russian vocabulary list. The most irregular patterns are seen in the most frequently occurring items and, therefore, should be learned early in the study of Russian. (Author/LMO)

English as Cultural Action.

ERIC Educational Resources Information Center

Prodromou, Luke

1988-01-01

Discusses teaching and learning English as a foreign language in its cultural context, and the culture of the native speaker of English and its relation to the culture of the learner. Native-speaking teachers should recognize the international status of English and work from local varieties of the language. (Author/LMO)

Conceptual Crossroads: Methods and Ethics in Ethnographic Evaluation.

ERIC Educational Resources Information Center

Fetterman, David M.

1986-01-01

The delicacy required of ethnographic work is nowhere more evident and more necessary than at the conceptual crossroads where methods and ethical decision making intersect. This paper addresses moments of decision and puts them into perspective by locating them within the lifecycle of ethnographic evaluation. (LMO)

Foamy Virus Vector Carries a Strong Insulator in Its Long Terminal Repeat Which Reduces Its Genotoxic Potential

PubMed Central

2017-01-01

ABSTRACT Strong viral enhancers in gammaretrovirus vectors have caused cellular proto-oncogene activation and leukemia, necessitating the use of cellular promoters in “enhancerless” self-inactivating integrating vectors. However, cellular promoters result in relatively low transgene expression, often leading to inadequate disease phenotype correction. Vectors derived from foamy virus, a nonpathogenic retrovirus, show higher preference for nongenic integrations than gammaretroviruses/lentiviruses and preferential integration near transcriptional start sites, like gammaretroviruses. We found that strong viral enhancers/promoters placed in foamy viral vectors caused extremely low immortalization of primary mouse hematopoietic stem/progenitor cells compared to analogous gammaretrovirus/lentivirus vectors carrying the same enhancers/promoters, an effect not explained solely by foamy virus' modest insertional site preference for nongenic regions compared to gammaretrovirus/lentivirus vectors. Using CRISPR/Cas9-mediated targeted insertion of analogous proviral sequences into the LMO2 gene and then measuring LMO2 expression, we demonstrate a sequence-specific effect of foamy virus, independent of insertional bias, contributing to reduced genotoxicity. We show that this effect is mediated by a 36-bp insulator located in the foamy virus long terminal repeat (LTR) that has high-affinity binding to the CCCTC-binding factor. Using our LMO2 activation assay, LMO2 expression was significantly increased when this insulator was removed from foamy virus and significantly reduced when the insulator was inserted into the lentiviral LTR. Our results elucidate a mechanism underlying the low genotoxicity of foamy virus, identify a novel insulator, and support the use of foamy virus as a vector for gene therapy, especially when strong enhancers/promoters are required. IMPORTANCE Understanding the genotoxic potential of viral vectors is important in designing safe and efficacious vectors for gene therapy. Self-inactivating vectors devoid of viral long-terminal-repeat enhancers have proven safe; however, transgene expression from cellular promoters is often insufficient for full phenotypic correction. Foamy virus is an attractive vector for gene therapy. We found foamy virus vectors to be remarkably less genotoxic, well below what was expected from their integration site preferences. We demonstrate that the foamy virus long terminal repeats contain an insulator element that binds CCCTC-binding factor and reduces its insertional genotoxicity. Our study elucidates a mechanism behind the low genotoxic potential of foamy virus, identifies a unique insulator, and supports the use of foamy virus as a vector for gene therapy. PMID:29046446

Microsurgical removal of epidermal and cortical cells: evidence that the gravitropic signal moves through the outer cell layers in primary roots of maize

NASA Technical Reports Server (NTRS)

Yang, R. L.; Evans, M. L.; Moore, R.

1990-01-01

There is general agreement that during root gravitropism some sort of growth-modifying signal moves from the cap to the elongation zone and that this signal ultimately induces the curvature that leads to reorientation of the root. However, there is disagreement regarding both the nature of the signal and the pathway of its movement from the root cap to the elongation zone. We examined the pathway of movement by testing gravitropism in primary roots of maize (Zea mays L.) from which narrow (0.5 mm) rings of epidermal and cortical tissue were surgically removed from various positions within the elongation zone. When roots were girdled in the apical part of the elongation zone gravitropic curvature occurred apical to the girdle but not basal to the girdle. Filling the girdle with agar allowed curvature basal to the girdle to occur. Shallow girdles, in which only two or three cell layers (epidermis plus one or two cortical cell layers) were removed, prevented or greatly delayed gravitropic curvature basal to the girdle. The results indicate that the gravitropic signal moves basipetally through the outermost cell layers, perhaps through the epidermis itself.

Analysis of buried interfaces in multilayer mirrors using grazing incidence extreme ultraviolet reflectometry near resonance edges.

PubMed

Sertsu, M G; Nardello, M; Giglia, A; Corso, A J; Maurizio, C; Juschkin, L; Nicolosi, P

2015-12-10

Accurate measurements of optical properties of multilayer (ML) mirrors and chemical compositions of interdiffusion layers are particularly challenging to date. In this work, an innovative and nondestructive experimental characterization method for multilayers is discussed. The method is based on extreme ultraviolet (EUV) reflectivity measurements performed on a wide grazing incidence angular range at an energy near the absorption resonance edge of low-Z elements in the ML components. This experimental method combined with the underlying physical phenomenon of abrupt changes of optical constants near EUV resonance edges enables us to characterize optical and structural properties of multilayers with high sensitivity. A major advantage of the method is to perform detailed quantitative analysis of buried interfaces of multilayer structures in a nondestructive and nonimaging setup. Coatings of Si/Mo multilayers on a Si substrate with period d=16.4  nm, number of bilayers N=25, and different capping structures are investigated. Stoichiometric compositions of Si-on-Mo and Mo-on-Si interface diffusion layers are derived. Effects of surface oxidation reactions and carbon contaminations on the optical constants of capping layers and the impact of neighboring atoms' interactions on optical responses of Si and Mo layers are discussed.

FT-IR study of CO 2 interaction with Na-rich montmorillonite

DOE PAGES

Krukowski, Elizabeth G.; Goodman, Angela; Rother, Gernot; ...

2015-05-27

Here, carbon capture, utilization and storage (CCUS) in saline reservoirs in sedimentary formations has the potential to reduce the impact of fossil fuel combustion on climate change by reducing CO 2 emissions to the atmosphere and storing the CO 2 in geologic formations in perpetuity. At pressure and temperature (PT) conditions relevant to CCUS, CO 2 is less dense than the pre-existing brine in the formation, and the more buoyant CO 2 will migrate to the top of the formation where it will be in contact with cap rock. Interactions between clay-rich shale cap rocks and CO 2 are poorlymore » understood at PT conditions appropriate for CCUS in saline formations. In this study, the interaction of CO 2 with clay minerals in the cap rock overlying a saline formation has been examined using Na + exchanged montmorillonite (Mt) (Na +-STx-1) (Na + Mt) as an analog for clay-rich shale. Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy (ATR-FTIR) was used to discern mechanistic information for CO 2 interaction with hydrated (both one- and two-water layers) and relatively dehydrated (both dehydrated layers and one-water layers) Na+-STx-1 at 35 °C and 50 C and CO 2 pressure from 0 5.9 MPa. CO 2-induced perturbations associated with the water layer and Na+-STx-1 vibrational modes such as AlAlOH and AlMgOH were examined. Data indicate that CO 2 is preferentially incorporated into the interlayer space, with relatively dehydrated Na +-STx-1 capable of incorporating more CO 2 compared to hydrated Na +-STx-1. Spectroscopic data provide no evidence of formation of carbonate minerals or the interaction of CO 2 with sodium cations in the Na +-STx-1 structure.« less

Enhanced direct-gap light emission from Si-capped n+-Ge epitaxial layers on Si after post-growth rapid cyclic annealing: impact of non-radiative interface recombination toward Ge/Si double heterostructure lasers.

PubMed

Higashitarumizu, Naoki; Ishikawa, Yasuhiko

2017-09-04

Enhanced direct-gap light emission is reported for Si-capped n + -Ge layers on Si after post-growth rapid cyclic annealing (RCA), and impact of non-radiative recombination (NRR) at the Ge/Si interface is discussed toward Ge/Si double heterostructure (DH) lasers. P-doped n + -Ge layer (1 × 10 19 cm -3 , 400 nm) is grown on Si by ultra-high vacuum chemical vapor deposition, followed by a growth of Si capping layer (5 nm) to form a Si/Ge/Si DH structure. Post-growth RCA to eliminate defects in Ge is performed in N 2 at temperatures between 900°C and 780°C, where the annealing time is minimized to be 5 s in each RCA cycle to prevent an out-diffusion of P dopants from the Ge surface. Direct-gap photoluminescence (PL) intensity at 1.6 µm increases with the RCA cycles up to 40, although the threading dislocation density in Ge is not reduced after 3 cycles in the present condition. The PL enhancement is ascribed to the suppression of NRR at the Ge/Si interface, where an intermixed SiGe alloy is formed. For Ge/Si DH lasers, NRR at the Ge/Si interface is found to have a significant impact on the threshold current density Jth. In order to achieve Jth on the order of 1 kA/cm 2 , similar to III-V lasers, the interface recombination velocity S is required below 10 3 cm/s in spite of S as large as 10 5 cm/s at the ordinary defect-rich Ge/Si interface.

Martian Polar Caps: Folding, Faulting, Flowing Glaciers of Multiple Interbedded Ices

NASA Astrophysics Data System (ADS)

Kargel, J. S.

2001-12-01

The Martian south polar cap (permanent CO2 cap and polar layered deposits), exhibit abundant, varied, and widespread deformational phenomena. Folding and boudinage are very common. Strike-slip or normal faults are rarer. Common in the vicinity of major troughs and scarps are signs of convergent flow tectonics manifested as wrinkle-ridge-like surface folds, thrust faults, and viscous forebulges with thin-skinned extensional crevasses and wrinkle-ridge folds. Such flow convergence is predicted by theory. Boudinage and folding at the 300-m wavelength scale, indicating rheologically contrasting materials, is widely exposed at deep levels along erosional scarps. Independent morphologic evidence indicates south polar materials of contrasting volatility. Hence, the south polar cap appears to be a multiphase structure of interbedded ices. The north polar cap locally also exhibits flow indicators, though they are neither as common nor as varied as in the south. The large-scale quasi-spiral structure of the polar caps could be a manifestation of large-scale boudinage. According to this scenario, deep-level boudinage continuously originates under the glacial divide (the polar cap summit). Rod-like boudin structures are oriented transverse to flow and migrate outward with the large-scale flow field. Troughs develop over areas between major boudins. A dynamic competition, and possibly a rough balance, develops between the local flow field in the vicinity of a trough (which tends to close the trough by lateral closure and upwelling flow) and sublimation erosion (which tends to widen and deepen them). Over time, the troughs flow to the margins of the polar cap where they, along with other polar structures, are destroyed by sublimation. Major ice types contributing to rheological and volatility layering may include, in order of highest to lowest mechanical strength, CO2 clathrate hydrate, water ice containing inert/insoluble dust, pure water ice, water ice containing traces of liquid-soluble salts, water ice containing traces of solid-soluble acids, CO2 ice. This is also nearly the same sequence of highest to lowest melting/dissociation points, but it is different than the sequence of volatility. This geologic-structural interpretation and specific chemical models are amenable to testing by computational means and point the way toward future needed observations, including complete high-resolution imaging of the polar caps, measurement of flow fields (possibly by laser interferometry), mapping of subsurface structures (by radar and/or seismic methods), and determination of composition (by penetrators, drillers, or borers). New lab data are needed on the physical properties of candidate ices.

Capping of rare earth silicide nanowires on Si(001)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Appelfeller, Stephan; Franz, Martin; Kubicki, Milan

The capping of Tb and Dy silicide nanowires grown on Si(001) was studied using scanning tunneling microscopy and cross-sectional high-resolution transmission electron microscopy. Several nanometers thick amorphous Si films deposited at room temperature allow an even capping, while the nanowires maintain their original structural properties. Subsequent recrystallization by thermal annealing leads to more compact nanowire structures and to troughs in the Si layer above the nanowires, which may even reach down to the nanowires in the case of thin Si films, as well as to V-shaped stacking faults forming along (111) lattice planes. This behavior is related to strain duemore » to the lattice mismatch between the Si overlayer and the nanowires.« less

Kinetics of Cold-Cap Reactions for Vitrification of Nuclear Waste Glass Based on Simultaneous Differential Scanning Calorimetry - Thermogravimetry (DSC-TGA) and Evolved Gas Analysis (EGA)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez, Carmen P.; Pierce, David A.; Schweiger, Michael J.

2013-12-03

For vitrifying nuclear waste glass, the feed, a mixture of waste with glass-forming and modifying additives, is charged onto the cold cap that covers 90-100% of the melt surface. The cold cap consists of a layer of reacting molten glass floating on the surface of the melt in an all-electric, continuous glass melter. As the feed moves through the cold cap, it undergoes chemical reactions and phase transitions through which it is converted to molten glass that moves from the cold cap into the melt pool. The process involves a series of reactions that generate multiple gases and subsequent massmore » loss and foaming significantly influence the mass and heat transfers. The rate of glass melting, which is greatly influenced by mass and heat transfers, affects the vitrification process and the efficiency of the immobilization of nuclear waste. We studied the cold-cap reactions of a representative waste glass feed using both the simultaneous differential scanning calorimetry thermogravimetry (DSC-TGA) and the thermogravimetry coupled with gas chromatography-mass spectrometer (TGA-GC-MS) as complementary tools to perform evolved gas analysis (EGA). Analyses from DSC-TGA and EGA on the cold-cap reactions provide a key element for the development of an advanced cold-cap model. It also helps to formulate melter feeds for higher production rate.« less

Biomimetic Deposition of Hydroxyapatite by Mixed Acid Treatment of Titanium Surfaces.

PubMed

Zhao, J M; Park, W U; Hwang, K H; Lee, J K; Yoon, S Y

2015-03-01

A simple chemical method was established for inducing bioactivity of Ti metal. In the present study, two kinds of mixed acid solutions were used to treat Ti specimens to induce Ca-P formation. Following a strong mixed acid activation process, Ca-P coatings successfully formed on the Ti surfaces in the simulated body fluid. Strong mixed acid etching was used to increase the roughness of the metal surface, because the porous and rough surfaces allow better adhesion between Ca-P coatings and substrate. Nano-scale modification of titanium surfaces can alter cellular and tissue responses, which may benefit osseointegration and dental implant therapy. Some specimens were treated with a 5 M NaOH aqueous solution, and then heat treated at 600 °C in order to form an amorphous sodium titanate layer on their surface. This treated titanium metal is believed to form a dense and uniform bone-like apatite layer on its surface in a simulated body fluid (SBF). This study proved that mixed acid treatment is not only important for surface passivation but is also another bioactive treatment for titanium surfaces, an alternative to alkali treatment. In addition, mixed acid treatment uses a lower temperature and shorter time period than alkali treatment.

A wind tunnel study of gaseous tracer dispersion in the convective boundary layer capped by a temperature inversion

NASA Astrophysics Data System (ADS)

Fedorovich, E.; Thäter, J.

Results are presented from wind tunnel simulations of gaseous pollutant dispersion in the atmospheric convective boundary layer (CBL) capped by a temperature inversion. The experiments were performed in the thermally stratified wind tunnel of the University of Karlsruhe, Germany. In the tunnel, the case of horizontally evolving, sheared CBL is reproduced. This distinguishes the employed experimental setup from the preceding laboratory and numerical CBL dispersion studies. The diffusive and mixing properties of turbulence in the studied CBL case have been found to be essentially dependent on the stage of the CBL evolution. Effects of the point source elevation on the horizontal variability of the concentration field, and on the ground level concentration as function of distance from the source have been investigated. The applicability of bottom-up/top-down diffusion concept in the simulated CBL case has been evaluated. The influence of surface wind shear and capping inversion strength on the pollutant dispersion and turbulent exchange across the CBL top has been demonstrated. The imposed positive shear across the inversion has been identified as inhibitor of the CBL growth. Comparisons of concentration patterns from the wind tunnel with water tank data are presented.

Deposition and properties of cobalt- and ruthenium-based ultra-thin films

NASA Astrophysics Data System (ADS)

Henderson, Lucas Benjamin

Future copper interconnect systems will require replacement of the materials that currently comprise both the liner layer(s) and the capping layer. Ruthenium has previously been considered as a material that could function as a single material liner, however its poor ability to prevent copper diffusion makes it incompatible with liner requirements. A recently described chemical vapor deposition route to amorphous ruthenium-phosphorus alloy films could correct this problem by eliminating the grain boundaries found in pure ruthenium films. Bias-temperature stressing of capacitor structures using 5 nm ruthenium-phosphorus film as a barrier to copper diffusion and analysis of the times-to-failure at accelerated temperature and field conditions implies that ruthenium-phosphorus performs acceptably as a diffusion barrier for temperatures above 165°C. The future problems associated with the copper capping layer are primarily due to the poor adhesion between copper and the current Si-based capping layers. Cobalt, which adheres well to copper, has been widely proposed to replace the Si-based materials, but its ability to prevent copper diffusion must be improved if it is to be successfully implemented in the interconnect. Using a dual-source chemistry of dicobaltoctacarbonyl and trimethylphosphine at temperatures from 250-350°C, amorphous cobalt-phosphorus can be deposited by chemical vapor deposition. The films contain elemental cobalt and phosphorus, plus some carbon impurity, which is incorporated in the film as both graphitic and carbidic (bonded to cobalt) carbon. When deposited on copper, the adhesion between the two materials remains strong despite the presence of phosphorus and carbon at the interface, but the selectivity for growth on copper compared to silicon dioxide is poor and must be improved prior to consideration for application in interconnect systems. A single molecule precursor containing both cobalt and phosphorus atoms, tetrakis(trimethylphosphine)cobalt(0), yields cobalt-phosphorus films without any co-reactant. However, the molecule does not contain sufficient amounts of amorphizing agents to fully eliminate grain boundaries, and the resulting film is nanocrystalline.

Light-Induced Acid Generation on a Gatekeeper for Smart Nitric Oxide Delivery.

PubMed

Choi, Hyung Woo; Kim, Jihoon; Kim, Jinhwan; Kim, Yonghwi; Song, Hyun Beom; Kim, Jeong Hun; Kim, Kimoon; Kim, Won Jong

2016-04-26

We report herein the design of a light-responsive gatekeeper for smart nitric oxide (NO) delivery. The gatekeeper is composed of a pH-jump reagent as an intermediary of stimulus and a calcium phosphate (CaP) coating as a shielding layer for NO release. The light irradiation and subsequent acid generation are used as triggers for uncapping the gatekeeper and releasing NO. The acids generated from a light-activated pH-jump agent loaded in the mesoporous nanoparticles accelerated the degradation of the CaP-coating layers on the nanoparticles, facilitating the light-responsive NO release from diazeniumdiolate by exposing a NO donor to physiological conditions. Using the combination of the pH-jump reagent and CaP coating, we successfully developed a light-responsive gatekeeper system for spatiotemporal-controlled NO delivery.

Generative Effects of Note-Taking during Science Lectures.

ERIC Educational Resources Information Center

Peper, Richard J.; Mayer, Richard E.

1986-01-01

In two experiments subjects were required to either take notes or not take notes while viewing a videotaped lecture on automobile engines. Results produced a pattern of interaction in which note-takers performed better on far-transfer tasks such as problem solving but worse on near-transfer tasks. (Author/LMO)

The Reliability and Validity of the Coopersmith Self-Esteem Inventory-Form B.

ERIC Educational Resources Information Center

Chiu, Lian-Hwang

1985-01-01

The purpose of this study was to determine the test-retest reliability and concurrent validity of the short form (Form B) of the Coopersmith Self-Esteem Inventory. Criterion measures for validity included: (1) sociometric measures; (2) teacher's popularity ranking; and, (3) self-esteem rating. (Author/LMO)

Race, Class, and the Attributional Process.

ERIC Educational Resources Information Center

Graham, Sandra; Long, Anna

1986-01-01

Two experiments were performed to examine the process of attributional thinking in Black and White children who differed in social class. Blacks did not display a less adaptive attributional pattern than did whites following actual performance on exams, and no differences existed in children's understanding of the meaning of causes. (Author/LMO)

An Analysis of the Dimensionality of the Pupil Control Ideology Scale.

ERIC Educational Resources Information Center

Graham, Steve; And Others

1985-01-01

The present study replicated an earlier investigation using the Pupil Control Ideology (PCI). The findings were congruent with earlier results. Consequently, it was recommended that the PCI should be refined and that the 10 item, unidimensional scale should be used in future investigations. (Author/LMO)

A Theoretical Analysis of Faculty Job Satisfaction/Dissatisfaction.

ERIC Educational Resources Information Center

Hill, Malcolm

1987-01-01

This study examines the issue of job satisfaction of college faculty from the perspective of Herzberg's "two-factor" theory and assesses the utility of the theory. Data from 1,089 full-time faculty in 20 college and university campuses supports that "intrinsic" factors contribute primarily to job satisfaction. (Author/LMO)

Assessment and Treatment of Tic Behavior: A Review and Case Study.

ERIC Educational Resources Information Center

Pray, Bruce, Jr.; And Others

1986-01-01

A discussion of the classification, differential diagnosis, etiology, assessment, and treatment of tic disorders is presented. A case study is included in which a school psychologist utilized behavioral consultation to assist a 9-year-old girl's parent and teacher in implementing a habit reversal program. (Author/LMO)

Hierarchies and the Choice of Left Conjuncts (With Particular Attention to English).

ERIC Educational Resources Information Center

Allan, K.

1987-01-01

Hierarchies have been identified as determinants of constituent order. The set of such hierarchies is reviewed and ranked as determinants of NP sequencing in English. The effect of a hierarchy in other languages is compared to and contrasted with what is found in English. (Author/LMO)

Using Demographic Subgroup and Dummy Variable Equations to Predict College Freshman Grade Average.

ERIC Educational Resources Information Center

Sawyer, Richard

1986-01-01

This study was designed to determine whether adjustments for the differential prediction observed among sex, racial/ethnic, or age subgroups in one freshman class at a college could be used to improve prediction accuracy for these subgroups in future freshman classes. (Author/LMO)

A Note on the Computation of the Second-Order Derivatives of the Elementary Symmetric Functions in the Rasch Model.

ERIC Educational Resources Information Center

Formann, Anton K.

1986-01-01

It is shown that for equal parameters explicit formulas exist, facilitating the application of the Newton-Raphson procedure to estimate the parameters in the Rasch model and related models according to the conditional maximum likelihood principle. (Author/LMO)

Independence and Exclusivity Among Psychological Processes: Implications for the Structure of Recall.

ERIC Educational Resources Information Center

Jones, Gregory V.

1987-01-01

It is suggested that theorists may develop both independence and exclusivity forms of multiple-process models, allowing choice between them to be made on empirical rather than a priori grounds. This theoretical approach is adopted in the specific case of memory retrival (Author/LMO)

Integrating Language Lab Materials into Advanced Russian.

ERIC Educational Resources Information Center

Allar, Gregory

1986-01-01

Describes the use of language lab materials supplied by the pedagogical journal "Russkij Jazyk Za Rubezom" in an advanced Russian-language class. Each week students were given a relevant picture and vocabulary list prior to listening to a taped story. The story was used as the basis for conversation. (LMO)

Benefit-Cost Analysis of the Perry Preschool Program and Its Policy Implications.

ERIC Educational Resources Information Center

Barnett, W. Steven

1985-01-01

Benefit-cost analysis is applied to the Perry Preschool Program and its long-term follow-up in order to examine preschool education as a social investment. The net present value of benefits and costs is positive, indicating that the program was a profitable social investment. (Author/LMO)

Afrikaner Identity: Diversity Among the Right.

ERIC Educational Resources Information Center

Louw-Potgieter, J.; Giles, H.

1987-01-01

Language is an important part of ethnic identity, but not the only one. Two groups of Afrikaners, 23 members of the National Party and 15 members of the Afrikaner Resistance Movement, responded to a questionnaire concerning characteristics essential for Afrikaner group membership. Culture and background were also perceived essential. (Author/LMO)

From Life in a French Town to the Artificial Heart: An Approach to the Teaching of Scientific French.

ERIC Educational Resources Information Center

Ross, Margaret E.

1988-01-01

Describes the experiences of one instructor in designing and implementing a short course in scientific French for upper level students majoring in applied biology at Glasgow College. Materials used and aspects of scientific language chosen are briefly discussed. (LMO)

Examiner Assessments of Clinical Performance: What Do They Tell Us About Clinical Competence?

ERIC Educational Resources Information Center

Maatsch, Jack L.

1987-01-01

This paper presents and interprets examiner and participant performance data obtained from an experimental field test of the test item and case simulation libraries of the American Board of Emergency Medicine Specialty Certificate Examination. Subjects were 94 medical students, residents, and emergency physicians. (Author/LMO)

Norm Theory: Comparing Reality to Its Alternatives.

ERIC Educational Resources Information Center

Kahneman, Daniel; Miller, Dale T.

1986-01-01

A theory of norms and normality is applied to some phenomena of emotional responses, social judgment, and conversations about causes. Norm theory is applied in analyses of enhanced emotional response to events that have abnormal causes, of generation of prediction from observations of behavior, and of the role of norms. (Author/LMO)

Self-Monitoring of Attained Subgoals in Private Study.

ERIC Educational Resources Information Center

Morgan, Mark

1985-01-01

Three conditions of self-monitoring of private study were compared for their effects on academic performance and intrinsic motivation. In end-of-year examinations, a group who self-monitored subgoals outperformed groups who self-monitored either time or study or distal goals on the target course of the investigation. (Author/LMO)

Recognition-by-Components: A Theory of Human Image Understanding.

ERIC Educational Resources Information Center

Biederman, Irving

1987-01-01

The theory proposed (recognition-by-components) hypothesizes the perceptual recognition of objects to be a process in which the image of the input is segmented at regions of deep concavity into an arrangement of simple geometric components. Experiments on the perception of briefly presented pictures support the theory. (Author/LMO)

The structure of crystallographic damage in GaN formed during rare earth ion implantation with and without an ultrathin AlN capping layer

NASA Astrophysics Data System (ADS)

Gloux, F.; Ruterana, P.; Wojtowicz, T.; Lorenz, K.; Alves, E.

2006-10-01

The crystallographic nature of the damage created in GaN implanted by rare earth ions at 300 keV and room temperature has been investigated by transmission electron microscopy versus the fluence, from 7×10 13 to 2×10 16 at/cm 2, using Er, Eu or Tm ions. The density of point defect clusters was seen to increase with the fluence. From about 3×10 15 at/cm 2, a highly disordered 'nanocrystalline layer' (NL) appears on the GaN surface. Its structure exhibits a mixture of voids and misoriented nanocrystallites. Basal stacking faults (BSFs) of I 1, E and I 2 types have been noticed from the lowest fluence, they are I 1 in the majority. Their density increases and saturates when the NL is observed. Many prismatic stacking faults (PSFs) with Drum atomic configuration have been identified. The I 1 BSFs are shown to propagate easily through GaN by folding from basal to prismatic planes thanks to the PSFs. When implanting through a 10 nm AlN cap, the NL threshold goes up to about 3×10 16 at/cm 2. The AlN cap plays a protective role against the dissociation of the GaN up to the highest fluences. The flat surface after implantation and the absence of SFs in the AlN cap indicate its high resistance to the damage formation.

Polar Cap Energy Deposition Events During the 5-6 August 2011 Magnetic Storm

NASA Astrophysics Data System (ADS)

Horvath, Ildiko; Lovell, Brian C.

2018-03-01

We study the 5-6 August 2011 storm for its energy deposition events occurring deep in the polar cap region, where the consequential localized intensifications of earthward directed Poynting flux led to the development of their related localized neutral density increases. For unraveling the underlying physical processes, we investigate the relations among Poynting flux intensifications, flow channels (FCs), and localized neutral density enhancements plus the nature of the underlying reconnection events. Observational results demonstrate Poynting flux increase deep in the polar cap in a FC-2 type FC during magnetopause reconnections and in a FC-4 type FC during lobe reconnections. During the latter stages of these different types of reconnection events, energy/momentum transfer occurred along old-open field lines and commonly led to the development of localized neutral density increases during their respective upwelling events fueled by field-aligned currents and above/within these polar FCs. The prevailing BY domination and the pulsed nature of this storm created favorable conditions for the development of these FC-2 and FC-4 types in the sunlit northern summer hemisphere and caused the observed Poynting flux intensifications deep in the polar cap. The solar wind source of these reconnections taking place along old-open field lines was situated in the high-latitude boundary layer. Thus, the high-latitude boundary layer dynamo provided a vigorous source of energy/momentum transfer during the latter-stage reconnections unfolding along old-open field lines.

An electromagnetic compressive force by cell exciter stimulates chondrogenic differentiation of bone marrow-derived mesenchymal stem cells.

PubMed

Park, Sang-Hyug; Sim, Woo Young; Park, Sin Wook; Yang, Sang Sik; Choi, Byung Hyune; Park, So Ra; Park, Kwideok; Min, Byoung-Hyun

2006-11-01

In this study, we present a biological micro-electromechanical system and its application to the chondrogenic differentiation of rabbit bone marrow-derived mesenchymal stem cells (MSCs). Actuated by an electromagnetic force, the micro cell exciter was designed to deliver a cyclic compressive load (CCL) with various magnitudes. Two major parts in the system are an actuator and a cartridge-type chamber. The former has a permanent magnet and coil, and the latter is equipped with 7 sample dishes and 7 metal caps. Mixed with a 2.4% alginate solution, the alginate/MSC layers were positioned in the sample dishes; the caps contained chondrogenic defined medium without transforming growth factor-beta (TGF-beta). Once powered, the actuator coil-derived electromagnetic force pulled the metal caps down, compressing the samples. The cyclic load was given at 1-Hz frequency for 10 min twice a day. Samples in the dishes without a cap served as a control. The samples were analyzed at 3, 5, and 7 days after stimulation for cell viability, biochemical assays, histologic features, immunohistochemistry, and gene expression of the chondrogenic markers. Applied to the alginate/MSC layer, the CCL system enhanced the synthesis of cartilage-specific matrix proteins and the chondrogenic markers, such as aggrecan, type II collagen, and Sox9. We found that the micromechanically exerted CCL by the cell exciter was very effective in enhancing the chondrogenic differentiation of MSCs, even without using exogenous TGF-beta.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abboud, Alexander; Guillen, Donna Post; Pokorny, Richard

At the Hanford site in the state of Washington, more than 56 million gallons of radioactive waste is stored in underground tanks. The cleanup plan for this waste is vitrification at the Waste Treatment Plant (WTP), currently under construction. At the WTP, the waste will be blended with glass-forming materials and heated to 1423K, then poured into stainless steel canisters to cool and solidify. A fundamental understanding of the glass batch melting process is needed to optimize the process to reduce cost and decrease the life cycle of the cleanup effort. The cold cap layer that floats on the surfacemore » of the glass melt is the primary reaction zone for the feed-to-glass conversion. The conversion reactions include water release, melting of salts, evolution of batch gases, dissolution of quartz and the formation of molten glass. Obtaining efficient heat transfer to this region is crucial to achieving high rates of glass conversion. Computational fluid dynamics (CFD) modeling is being used to understand the heat transfer dynamics of the system and provide insight to optimize the process. A CFD model was developed to simulate the DM1200, a pilot-scale melter that has been extensively tested by the Vitreous State Laboratory (VSL). Electrodes are built into the melter to provide Joule heating to the molten glass. To promote heat transfer from the molten glass into the reactive cold cap layer, bubbling of the molten glass is used to stimulate forced convection within the melt pool. A three-phase volume of fluid approach is utilized to model the system, wherein the molten glass and cold cap regions are modeled as separate liquid phases, and the bubbling gas and plenum regions are modeled as one lumped gas phase. The modeling of the entire system with a volume of fluid model allows for the prescription of physical properties on a per-phase basis. The molten glass phase and the gas phase physical properties are obtained from previous experimental work. Finding representative properties for the cold cap region is more difficult, as this region is not a true liquid, but rather a multilayer region consisting of a porous and a foamy layer. Physical properties affecting heat transfer, namely the thermal conductivity and heat capacity, have been fit to closely match data and observations from laboratory experiments. Data from xray tomography and quenching of laboratory-scale cold caps provide insight into the topology of bubble distribution within the cold cap at various temperatures. Heat transfer within the melter was validated by comparison with VSL data for the pilot-scale melter.« less

Landscape Evolution and the Reincarnation of the Residual CO2 Ice Cap of Mars

NASA Astrophysics Data System (ADS)

Byrne, S.; Zuber, M.

2006-12-01

Observations of the southern residual CO2 cap of Mars reveal a wide range of landforms including flat-floored quasi-circular pits with steep walls (dubbed Swiss-cheese features). Interannual comparisons show that these depressions are expanding laterally at rates of ~2m/yr to ~4m/yr, prompting suggestions of climate change. The residual CO2 ice cap is up to 10m thick and underlain by an involatile basement, it also contains layers roughly 2m thick representing different accumulation episodes in the recent past. Changes in the appearance of the residual ice between the Mariner 9 and Viking missions indicate that the top-most layer was deposited in that time-frame, soon after the global dust storm of 1971. The spatial density of the Swiss-cheese features, and the rate at which they expand, mean that it is unlikely that any part of the residual ice cap is older than a few centuries. Given this, we may ask: how can there be a residual cap present today for us to observe? To answer this and other questions we have developed a model to examine the evolution of a CO2 ice landscape. This model reproduces the morphologies and expansion rates seen in the actual residual CO2 ice cap. Our model results indicate that the fate of CO2 ice surfaces is controlled by their surface roughness. Surface roughness always increases with time, which results in an unstable situation. When the surface roughness exceeds a critical point small pits can begin to develop. The walls of these pits rapidly steepen and begin retreating which enlarges and deepens the pit. This situation always occurs even if the surface of the CO2 slab has a high enough albedo to have a net mass gain each year. Once these pits begin expanding they quickly erode the entire ice slab. When the underlying non-CO2 material is exposed, it will not frost over again if Mars were to repeat like clockwork every year. We conclude that interannual climatic variability is actually a requirement for the continued existence of a residual CO2 ice cap. We invoke unusual depositional episodes (which have a surface smoothing effect) after which the cap can begin accumulating mass and growing in thickness again. This continues until the surface roughness again exceeds a stable state and the process repeats itself. The thickness of the residual cap therefore oscillates on timescales of centuries. The total cap volume may also be affected by variations in residual cap extent. The cap is not 'stable' in the usual sense of the word, but instead is constantly being destroyed and recreated. Evidence suggests that these rejuvenating depositional events are linked to global dust storms. The 10m thick stratigraphic record thus provides a unique measure of interannual variability of the current climate, the expanding Swiss-cheese features do not indicate secular climate change, but instead are just part of the larger life-cycle of this ice deposit. We will report on this surface modeling which reproduces other morphologies within the residual cap and present a historical model based on combining our modeling with the feature sizes and ablation rates found within the present residual ice cap.

Diatom ooze as weak layer for submarine mega-slides off Northwest Africa: Evidence from core-seismic integration in the Cap Blanc Slide area

NASA Astrophysics Data System (ADS)

Urlaub, Morelia; Geersen, Jacob; Krastel, Sebastian; Schwenk, Tilmann

2017-04-01

The continental slope off Northwest Africa has experienced at least four mega-landslides, each affecting over 20,000 km2 of seafloor. Although the landslides lie more than 400 km apart, they have many similar characteristics, including stepped headwall patterns and several bedding-parallel glide planes at slope angles of <2°. This morphology suggests that failures took place along multiple mechanically weak sedimentary layers that are present at different stratigraphic depths. From all Northwest African mega-landslides the Cap Blanc Slide, situated off the coasts of Mauretania and West Sahara, offers an unprecedented possibility to advance our understanding of landslide causes. ODP site 658 (Leg 108) was drilled within the evacuation area of the slide, recovering its glide plane. In addition, site 658 also recovered the glide plane and the overlying undisturbed sedimentary sequence of a younger slope failure, which took place within the evacuation are of the main Cap Blanc Slide at some distance to the borehole. We use core-seismic integration to characterize the glide planes as well as to determine the timing of slope failures. The sediments just above both glide planes have particularly high biogenic opal contents owing to the presence of large amounts of diatom microfossils. Diatoms are hollow structures of microfossil skeletons, which contain large amounts of bound and intraskeletal water. When a critical stress level is exceeded during compaction, the microfossil shells break. The stored water is released causing a sudden increase in pore pressure, which may facilitate slope failure. We therefore suggest that diatom oozes acted as weak layers in the case of the Cap Blanc Slide. Pronounced biogenic opal maxima occur during glacial terminations and are expected all along the Northwest African continental margin. We thus hypothesize that mega-slides off Northwest Africa, and potentially also at other continental margins, are preconditioned by episodically high deposition of biogenic opal.

Gigantic perpendicular magnetic anisotropy of heavy transition metal cappings on Fe/MgO(0 0 1)

NASA Astrophysics Data System (ADS)

Taivansaikhan, P.; Odkhuu, D.; Rhim, S. H.; Hong, S. C.

2017-11-01

Effects of capping layer by 5d transition metals (TM = Hf, Ta, W, Re, Os, Ir, Pt, and Au) on Fe/MgO(0 0 1), a typical magnetic tunneling junction, are systematically investigated using first-principles calculation for magnetism and magnetocrystalline-anisotropy (MCA). The early TMs having less than half-filled d bands favor magnetization antiparallel to Fe, whereas the late TMs having more than half-filled d bands favor parallel, which is explained in the framework of kinetic exchange energy. The Os capping, isovalent to Fe, enhances MCA significantly to gigantic energy of +11.31 meV/cell, where positive contribution is mostly from the partially filled majority d bands of magnetic quantum number of |m| = 1 along with stronger spin-orbit coupling of Os than Fe. Different TM cappings give different MCA energies as the Fermi level shifts according to the valence of TM: Re and Ir, just one valence more or less than Os, have still large PMCA but smaller than the Os. In the W and Pt cappings, valence difference by two, PMCA are further reduced; MCAs are lowered compared to Fe/MgO(0 0 1) by the cappings of the very early TMs (Hf and Ta), while the very late TM (Au) switches sign to in-plane MCA.

Selective etching of InGaAs/GaAs(100) multilayers of quantum-dot chains

NASA Astrophysics Data System (ADS)

Wang, Zh. M.; Zhang, L.; Holmes, K.; Salamo, G. J.

2005-04-01

We report selective chemical etching as a promising procedure to study the buried quantum dots in multiple InGaAs/GaAs layers. The dot layer-by-dot layer etching is demonstrated using a mixed solution of NH4OH:H2O2:H2O. Regular plan-view atomic force microscopy reveals that all of the exposed InGaAs layers have a chain-like lateral ordering despite the potential of significant In-Ga intermixing during capping. The vertical self-correlation of quantum dots in the chains is observed.

Achievement of normally-off AlGaN/GaN high-electron mobility transistor with p-NiOx capping layer by sputtering and post-annealing

NASA Astrophysics Data System (ADS)

Huang, Shyh-Jer; Chou, Cheng-Wei; Su, Yan-Kuin; Lin, Jyun-Hao; Yu, Hsin-Chieh; Chen, De-Long; Ruan, Jian-Long

2017-04-01

In this paper, we present a technique to fabricate normally off GaN-based high-electron mobility transistor (HEMT) by sputtering and post-annealing p-NiOx capping layer. The p-NiOx layer is produced by sputtering at room temperature and post-annealing at 500 °C for 30 min in pure O2 environment to achieve high hole concentration. The Vth shifts from -3 V in the conventional transistor to 0.33 V, and on/off current ratio became 107. The forward and reverse gate breakdown increase from 3.5 V and -78 V to 10 V and -198 V, respectively. The reverse gate leakage current is 10-9 A/mm, and the off-state drain-leakage current is 10-8 A/mm. The Vth hysteresis is extremely small at about 33 mV. We also investigate the mechanism that increases hole concentration of p-NiOx after annealing in oxygen environment resulted from the change of Ni2+ to Ni3+ and the surge of (111)-orientation.

Patterning of magnetic thin films and multilayers using nanostructured tantalum gettering templates.

PubMed

Qiu, Wenlan; Chang, Long; Lee, Dahye; Dannangoda, Chamath; Martirosyan, Karen; Litvinov, Dmitri

2015-03-25

This work demonstrates that a nonmagnetic thin film of cobalt oxide (CoO) sandwiched between Ta seed and capping layers can be effectively reduced to a magnetic cobalt thin film by annealing at 200 °C, whereas CoO does not exhibit ferromagnetic properties at room temperature and is stable at up to ∼400 °C. The CoO reduction is attributed to the thermodynamically driven gettering of oxygen by tantalum, similar to the exothermic reduction-oxidation reaction observed in thermite systems. Similarly, annealing at 200 °C of a nonmagnetic [CoO/Pd]N multilayer thin film sandwiched between Ta seed and Ta capping layers results in the conversion into a magnetic [Co/Pd]N multilayer, a material with perpendicular magnetic anisotropy that is of interest for magnetic data storage applications. A nanopatterning approach is introduced where [CoO/Pd]N multilayers is locally reduced into [Co/Pd]N multilayers to achieve perpendicular magnetic anisotropy nanostructured array. This technique can potentially be adapted to nanoscale patterning of other systems for which thermodynamically favorable combination of oxide and gettering layers can be identified.

Superfund Record of Decision (EPA Region 3): Allegany Ballistics Laboratory (USNavy), Operable Unit 1, Mineral, WV, February 12, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-01-01

This decision document presents the selected remedial action for Site 5 Landfill Contents and Surface Soil at the Allegany Ballistics Laboratory (ABL), Rocket Center, West Virginia. The major components of the selected remedy are: Deed notation along with property use and limited access restrictions; Installation of a composite CAP-GCL and FMC; Installation of a drainage layer utilizing a geonet; Installation of a passive landfill gas (LFG) venting system; Revegetation of the capped area; Installation of perimeter drainage system; and Post-closure requirements.

Present-day Exposures of Water Ice in the Northern Mid-latitudes of Mars

NASA Technical Reports Server (NTRS)

Allen, Carlton C.; Kanner, Lisa C.

2007-01-01

Water ice is exposed in the martian north polar cap, but is rarely exposed beyond the cap boundary. Orbital gamma ray spectrometry data strongly imply the presence of water ice within meters of the surface at latitudes north of approximately 60deg. We have examined mid-latitude areas of the northern plains displaying residual ice-rich layers, and report evidence of present-day surface exposures of water ice. These exposures, if confirmed, could con-strain the latitudinal and temporal stability of surface ice on Mars.

Stable carbon and oxygen isotope record of central Lake Erie sediments

USGS Publications Warehouse

Tevesz, M.J.S.; Spongberg, A.L.; Fuller, J.A.

1998-01-01

Stable carbon and oxygen isotope data from mollusc aragonite extracted from sediment cores provide new information on the origin and history of sedimentation in the southwestern area of the central basin of Lake Erie. Sediments infilling the Sandusky subbasin consist of three lithologic units overlying glacial deposits. The lowest of these is a soft gray mud overlain by a shell hash layer containing Sphaerium striatinum fragments. A fluid mud unit caps the shell hash layer and extends upwards to the sediment-water interface. New stable isotope data suggest that the soft gray mud unit is of postglacial, rather than proglacial, origin. These data also suggest that the shell hash layer was derived from erosional winnowing of the underlying soft gray mud layer. This winnowing event may have occurred as a result of the Nipissing flood. The Pelee-Lorain moraine, which forms the eastern boundary of the Sandusky subbasin, is an elevated area of till capped by a sand deposit that originated as a beach. The presence of both the shell hash layer and relict beach deposit strengthens the interpretation that the Nipissing flood was a critical event in the development of the southwestern area of the central basin of Lake Erie. This event, which returned drainage from the upper lakes to the Lake Erie basin, was a dominant influence on regional stratigraphy, bathymetry, and depositional setting.

Core-level spectra and binding energies of transition metal nitrides by non-destructive x-ray photoelectron spectroscopy through capping layers

NASA Astrophysics Data System (ADS)

Greczynski, G.; Primetzhofer, D.; Lu, J.; Hultman, L.

2017-02-01

We present the first measurements of x-ray photoelectron spectroscopy (XPS) core level binding energies (BE:s) for the widely-applicable group IVb-VIb polycrystalline transition metal nitrides (TMN's) TiN, VN, CrN, ZrN, NbN, MoN, HfN, TaN, and WN as well as AlN and SiN, which are common components in the TMN-based alloy systems. Nitride thin film samples were grown at 400 °C by reactive dc magnetron sputtering from elemental targets in Ar/N2 atmosphere. For XPS measurements, layers are either (i) Ar+ ion-etched to remove surface oxides resulting from the air exposure during sample transfer from the growth chamber into the XPS system, or (ii) in situ capped with a few nm thick Cr or W overlayers in the deposition system prior to air-exposure and loading into the XPS instrument. Film elemental composition and phase content is thoroughly characterized with time-of-flight elastic recoil detection analysis (ToF-E ERDA), Rutherford backscattering spectrometry (RBS), and x-ray diffraction. High energy resolution core level XPS spectra acquired with monochromatic Al Kα radiation on the ISO-calibrated instrument reveal that even mild etching conditions result in the formation of a nitrogen-deficient surface layer that substantially affects the extracted binding energy values. These spectra-modifying effects of Ar+ ion bombardment increase with increasing the metal atom mass due to an increasing nitrogen-to-metal sputter yield ratio. The superior quality of the XPS spectra obtained in a non-destructive way from capped TMN films is evident from that numerous metal peaks, including Ti 2p, V 2p, Zr 3d, and Hf 4f, exhibit pronounced satellite features, in agreement with previously published spectra from layers grown and analyzed in situ. In addition, the N/metal concentration ratios are found to be 25-90% higher than those obtained from the corresponding ion-etched surfaces, and in most cases agree very well with the RBS and ToF-E ERDA values. The N 1 s BE:s extracted from capped TMN films, thus characteristic of a native surface, show a systematic trend, which contrasts with the large BE spread of literature "reference" values. Hence, non-destructive core level XPS employing capping layers provides an opportunity to obtain high-quality spectra, characteristic of virgin in situ grown and analyzed TMN films, although with larger versatility, and allows for extracting core level BE values that are more reliable than those obtained from sputter-cleaned N-deficient surfaces. Results presented here, recorded from a consistent set of binary TMN's grown under the same conditions and analyzed in the same instrument, provide a useful reference for future XPS studies of multinary materials systems allowing for true deconvolution of complex core level spectra.

Vowel Harmony in Palestinian Arabic: A Metrical Perspective.

ERIC Educational Resources Information Center

Abu-Salim, I. M.

1987-01-01

The autosegmental rule of vowel harmony (VH) in Palestinian Arabic is shown to be constrained simultaneously by metrical and segmental boundaries. The indicative prefix bi- is no longer an exception to VH if a structure is assumed that disallows the prefix from sharing a foot with the stem, consequently blocking VH. (Author/LMO)

Interfacing Optical Document Scanners: Principles and Practical Considerations.

ERIC Educational Resources Information Center

Krus, David J.; Kodimer, Dennis

1987-01-01

Handlers for interfacing the ScanTron and 2700 Optical Mark Readers with the IBM AT/XT/PC and Tandy 2000/1000/3000 iAPX 88/186/286 based computers were described. Differences between programing an RS232C serial port using BIOS interrupts and directly addressing the Motorola 8550 ART microprocessor were discussed. (Author/LMO)

Gender-Based Differential Item Performance in Mathematics Achievement Items.

ERIC Educational Resources Information Center

Doolittle, Allen E.; Cleary, T. Anne

1987-01-01

Eight randomly equivalent samples of high school seniors were each given a unique form of the ACT Assessment Mathematics Usage Test (ACTM). Signed measures of differential item performance (DIP) were obtained for each item in the eight ACTM forms. DIP estimates were analyzed and a significant item category effect was found. (Author/LMO)

A Program That Acquires Language Using Positive and Negative Feedback.

ERIC Educational Resources Information Center

Brand, James

1987-01-01

Describes the language learning program "Acquire," which is a sample of grammar induction. It is a learning algorithm based on a pattern-matching scheme, using both a positive and negative network to reduce overgeneration. Language learning programs may be useful as tutorials for learning the syntax of a foreign language. (Author/LMO)

Are Learning Disabled Students "Test-Wise?": An Inquiry into Reading Comprehension Test Items.

ERIC Educational Resources Information Center

Scruggs, Thomas E.; Lifson, Steve

1986-01-01

Two experiments compared the ability of learning disabled (LD) students and more typical age peers to answer such reading comprehension questions presented independently of reading passages. Results suggested a relative deficiency on the part of LD students with respect to reasoning strategies and test-taking skills. (Author/LMO)

Personality Changes as a Function of Minimum Competency Test Success or Failure.

ERIC Educational Resources Information Center

Richman, Charles L.; And Others

1987-01-01

The psychological effects of success and failure on the North Carolina Minimum Competency Test (MCT) were examined. Subjects were high school students, who were pre- and post-tested using the Rosenberg Self Esteem Scale and the High School Personality Questionnaire. Self-esteem decreased following knowledge of MCT failure. (LMO)

Toward Wider Use of Literature in ESL: Why and How.

ERIC Educational Resources Information Center

Gajdusek, Linda

1988-01-01

Discusses English as a second language (ESL) theory as it relates to the use of literature, and presents a four-step approach to any literary text that obliges ESL students to take responsibility for building their own successively more complex schemata. This approach is illustrated with Hemingway's short story "Soldier's Home." (Author/LMO)

The Construct Validity of Higher Order Structure-of-Intellect Factors Reflecting Semantic and Symbolic Content Abilities.

ERIC Educational Resources Information Center

Khattab, Ali-Maher; Michael, William B.

1986-01-01

Based on reanalyses of correlational data obtained from the University of Southern California Aptitudes Research Project, this investigation examined the extent to which two higher order factors of semantic content and symbolic content form Guilford's structure-of-intellect model reflected distinct constructs. (Author/LMO)

The Application of Strength of Association Statistics to the Item Analysis of an In-Training Examination in Diagnostic Radiology.

ERIC Educational Resources Information Center

Diamond, James J.; McCormick, Janet

1986-01-01

Using item responses from an in-training examination in diagnostic radiology, the application of a strength of association statistic to the general problem of item analysis is illustrated. Criteria for item selection, general issues of reliability, and error of measurement are discussed. (Author/LMO)

Gifted and Talented Education: A National Test Case in Peoria.

ERIC Educational Resources Information Center

Fetterman, David M.

1986-01-01

This article presents a study of a program in Peoria, Illinois, for the gifted and talented that serves as a national test case for gifted education and minority enrollment. It was concluded that referral, identification, and selection were appropriate for the program model but that inequalities resulted from socioeconomic variables. (Author/LMO)

Italian In-Field EST Users Self-Assess Their Macro- and Micro-Level Needs: A Case Study.

ERIC Educational Resources Information Center

Tarantino, Maria

1988-01-01

Presents and discusses results of study on the specific linguistics needs of Italian scientists who must use English for science and technology for study and work purposes. Writing and listening were considered to be the most difficult skills to master. Questionnaire appears in Appendix. (LMO)

Comprehensive Enhancement of Nanostructured Lithium-Ion Battery Cathode Materials via Conformal Graphene Dispersion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Kan-Sheng; Xu, Rui; Luu, Norman S.

Efficient energy storage systems based on lithium-ion batteries represent a critical technology across many sectors including consumer electronics, electrified transportation, and a smart grid accommodating intermittent renewable energy sources. Nanostructured electrode materials present compelling opportunities for high-performance lithium-ion batteries, but inherent problems related to the high surface area to volume ratios at the nanometer-scale have impeded their adoption for commercial applications. Here, we demonstrate a materials and processing platform that realizes high-performance nanostructured lithium manganese oxide (nano-LMO) spinel cathodes with conformal graphene coatings as a conductive additive. The resulting nanostructured composite cathodes concurrently resolve multiple problems that have plagued nanoparticle-basedmore » lithium-ion battery electrodes including low packing density, high additive content, and poor cycling stability. Moreover, this strategy enhances the intrinsic advantages of nano-LMO, resulting in extraordinary rate capability and low temperature performance. With 75% capacity retention at a 20C cycling rate at room temperature and nearly full capacity retention at -20 degrees C, this work advances lithium-ion battery technology into unprecedented regimes of operation.« less

Expression profiles of adult T-cell leukemia–lymphoma and associations with clinical responses to zidovudine and interferon α

PubMed Central

ALIZADEH, ASH A.; BOHEN, SEAN P.; LOSSOS, CHEN; MARTINEZ-CLIMENT, JOSE A.; RAMOS, JUAN CARLOS; CUBEDO-GIL, ELENA; HARRINGTON, WILLIAM J.; LOSSOS, IZIDORE S.

2014-01-01

Adult T-cell leukemia–lymphoma (ATLL) is an HTLV-1-associated lymphoproliferative malignancy that is frequently fatal. We compared gene expression profiles (GEPs) of leukemic specimens from nine patients with ATLL at the time of diagnosis and immediately after combination therapy with zidovudine (AZT) and interferon α (IFNα). GEPs were also related to genetic aberrations determined by comparative genomic hybridization. We identified several genes anomalously over-expressed in the ATLL leukemic cells at the mRNA level, including LYN, CSPG2, and LMO2, and confirmed LMO2 expression in ATLL cells at the protein level. In vivo AZT–IFNα therapy evoked a marked induction of interferon-induced genes accompanied by repression of cell-cycle regulated genes, including those encoding ribosomal proteins. Remarkably, patients not responding to AZT–IFNα differed most from responding patients in lower expression of these same IFN-responsive genes, as well as components of the antigen processing and presentation apparatus. Demonstration of specific gene expression signatures associated with response to AZT–IFNα therapy may provide novel insights into the mechanisms of action in ATLL. PMID:20370541

Total antioxidant capacity and total oxidant status of synovial fluids in patients with temporomandibular joint pain and dysfunction.

PubMed

Etöz, Osman A; Akçay, Hüseyin; Neşelioğlu, Salim; Erel, Özcan; Alkan, Alper

2012-12-01

The objective of this study was to investigate whether a relationship exists between total antioxidant capacity (TAC) and total oxidant status (TOS) of synovial fluids (SFs) of temporomandibular joint (TMJ) pain patients with pain and dysfunction. Forty-two patients with TMJ pain were included in this study. TAC and TOS values of SFs were measured with a novel colorimetric method. Independent t test and correlations were used to analyze the data. TAC of SFs in patients with TMJ pain and limited mouth opening (LMO; n = 21) were significantly lower (P = 0.03) than patients without LMO (n = 21). TOS of SF was negatively correlated with duration of the disease. There was no correlation between TAC, TOS, and VAS scores of the patients as well as age and maximum mouth opening values. Antioxidant response to oxidative changes (TAC and TOS) in SF decreased as the stage of dysfunction increased. Local administration of antioxidant agents might be considered in management of TMJ pain and dysfunction to prevent possible increased oxidative stress.

Comprehensive Enhancement of Nanostructured Lithium-Ion Battery Cathode Materials via Conformal Graphene Dispersion.

PubMed

Chen, Kan-Sheng; Xu, Rui; Luu, Norman S; Secor, Ethan B; Hamamoto, Koichi; Li, Qianqian; Kim, Soo; Sangwan, Vinod K; Balla, Itamar; Guiney, Linda M; Seo, Jung-Woo T; Yu, Xiankai; Liu, Weiwei; Wu, Jinsong; Wolverton, Chris; Dravid, Vinayak P; Barnett, Scott A; Lu, Jun; Amine, Khalil; Hersam, Mark C

2017-04-12

Efficient energy storage systems based on lithium-ion batteries represent a critical technology across many sectors including consumer electronics, electrified transportation, and a smart grid accommodating intermittent renewable energy sources. Nanostructured electrode materials present compelling opportunities for high-performance lithium-ion batteries, but inherent problems related to the high surface area to volume ratios at the nanometer-scale have impeded their adoption for commercial applications. Here, we demonstrate a materials and processing platform that realizes high-performance nanostructured lithium manganese oxide (nano-LMO) spinel cathodes with conformal graphene coatings as a conductive additive. The resulting nanostructured composite cathodes concurrently resolve multiple problems that have plagued nanoparticle-based lithium-ion battery electrodes including low packing density, high additive content, and poor cycling stability. Moreover, this strategy enhances the intrinsic advantages of nano-LMO, resulting in extraordinary rate capability and low temperature performance. With 75% capacity retention at a 20C cycling rate at room temperature and nearly full capacity retention at -20 °C, this work advances lithium-ion battery technology into unprecedented regimes of operation.

Study of Growth Kinetics in One Dimensional and Two Dimensional ZnO Nanostructures

NASA Astrophysics Data System (ADS)

Yin, Xin

Because of the merits arising from the unique geometry, nanostructure materials have been an essential class of materials, which have shown great potentials in the fields of electronics, photonics, and biology. With various nanostructures being intensively investigated and successfully complemented into device applications, there has been one increasing demand to the investigation of the growth mechanism devoted to the controlled nanostructure synthesis. Motivated by this situation, this thesis is focused on the fundamental understanding of the nanostructure growth. Specifically, by taking zinc oxide as an example material, through controlling the basic driving force, that is, the supersaturation, I have rationally designed and synthesized various of nanostructures, and further applied the classical layer-by-layer growth mechanism to the understanding on the formation of these nanostructures, they are, the convex-plate-capped nanowires, the concave-plate-capped nanowires, the facet evolution at the tip of the nanowires, and the ultrathin 2D nanosheets.

Modeling the Martian seasonal CO2 cycle. I - Fitting the Viking Lander pressure curves. II - Interannual variability

NASA Technical Reports Server (NTRS)

Wood, Stephen E.; Paige, David A.

1992-01-01

The present diurnal and seasonal thermal model for Mars, in which surface CO2 frost condensation and sublimation are determined by the net effects of radiation, latent heat, and heat conduction in subsurface soil layers, in order to simulate seasonal exchanges of CO2 between the polar caps and atmosphere, successfully reproduces the measured pressured variations at the Viking Lander 1 site. In the second part of this work, the year-to-year differences between measured surface pressures at Viking sites as a function of season are used as upper limits on the potential magnitudes of interannual variations in the Martian atmosphere's mass. Simulations indicate that the dust layers deposited onto the condensing north seasonal polar cap during dust storms can darken seasonal frost deposits upon their springtime uncovering, while having little effect on seasonal pressure variations.

Tuning charge transport in pentacene thin-film transistors using the strain-induced electron-phonon coupling modification

NASA Astrophysics Data System (ADS)

Lin, Yow-Jon; Chang, Hsing-Cheng; Liu, Day-Shan

2015-03-01

Tuning charge transport in the bottom-contact pentacene-based organic thin-film transistors (OTFTs) using a MoO x capping layer that serves to the electron-phonon coupling modification is reported. For OTFTs with a MoO x front gate, the enhanced field-effect carrier mobility is investigated. The time domain data confirm the electron-trapping model. To understand the origin of a mobility enhancement, an analysis of the temperature-dependent Hall-effect characteristics is presented. Similarly, the Hall-effect carrier mobility was dramatically increased by capping a MoO x layer on the pentacene front surface. However, the carrier concentration is not affected. The Hall-effect carrier mobility exhibits strong temperature dependence, indicating the dominance of tunneling (hopping) at low (high) temperatures. A mobility enhancement is considered to come from the electron-phonon coupling modification that results from the contribution of long-lifetime electron trapping.

Controlled assembly of graphene-capped nickel, cobalt and iron silicides

PubMed Central

Vilkov, O.; Fedorov, A.; Usachov, D.; Yashina, L. V.; Generalov, A. V.; Borygina, K.; Verbitskiy, N. I.; Grüneis, A.; Vyalikh, D. V.

2013-01-01

The unique properties of graphene have raised high expectations regarding its application in carbon-based nanoscale devices that could complement or replace traditional silicon technology. This gave rise to the vast amount of researches on how to fabricate high-quality graphene and graphene nanocomposites that is currently going on. Here we show that graphene can be successfully integrated with the established metal-silicide technology. Starting from thin monocrystalline films of nickel, cobalt and iron, we were able to form metal silicides of high quality with a variety of stoichiometries under a Chemical Vapor Deposition grown graphene layer. These graphene-capped silicides are reliably protected against oxidation and can cover a wide range of electronic materials/device applications. Most importantly, the coupling between the graphene layer and the silicides is rather weak and the properties of quasi-freestanding graphene are widely preserved. PMID:23835625

Electrical characteristics of proton-irradiated Sc2O3 passivated AlGaN/GaN high electron mobility transistors

NASA Astrophysics Data System (ADS)

Luo, B.; Kim, Jihyun; Ren, F.; Gillespie, J. K.; Fitch, R. C.; Sewell, J.; Dettmer, R.; Via, G. D.; Crespo, A.; Jenkins, T. J.; Gila, B. P.; Onstine, A. H.; Allums, K. K.; Abernathy, C. R.; Pearton, S. J.; Dwivedi, R.; Fogarty, T. N.; Wilkins, R.

2003-03-01

Sc2O3-passivated AlGaN/GaN high electron mobility transistors (HEMTs) were irradiated with 40 MeV protons to a fluence corresponding to approximately 10 years in low-earth orbit (5×109 cm-2). Devices with an AlGaN cap layer showed less degradation in dc characteristics than comparable GaN-cap devices, consistent with differences in average band energy. The changes in device performance could be attributed completely to bulk trapping effects, demonstrating that the effectiveness of the Sc2O3 layers in passivating surface states in the drain-source region was undiminished by the proton irradiation. Sc2O3-passivated AlGaN/HEMTs appear to be attractive candidates for space and terrestrial applications where resistance to high fluxes of ionizing radiation is a criteria.

Inverted channel deposits on the floor of Miyamoto crater, Mars

USGS Publications Warehouse

Newsom, Horton E.; Lanza, N.L.; Ollila, A.M.; Wiseman, S.M.; Roush, T.L.; Marzo, G.A.; Tornabene, L.L.; Okubo, C.H.; Osterloo, M.M.; Hamilton, V.E.; Crumpler, L.S.

2010-01-01

Morphological features on the western floor of Miyamoto crater in southwestern Meridiani Planum, Mars, are suggestive of past fluvial activity. Imagery from the High Resolution Imaging Science Experiment (HiRISE) gives a detailed view of raised curvilinear features that appear to represent inverted paleochannel deposits. The inverted terrain appears to be capped with a resistant, dark-toned deposit that is partially covered by unconsolidated surficial materials. Subsequent to deposition of the capping layer, erosion of the surrounding material has left the capping materials perched on pedestals of uneroded basal unit material. Neither the capping material nor the surrounding terrains show any unambiguous morphological evidence of volcanism or glaciation. The capping deposit may include unconsolidated or cemented stream deposits analogous to terrestrial inverted channels in the Cedar Mountain Formation near Green River, Utah. In addition to this morphological evidence for fluvial activity, phyllosilicates have been identified in the basal material on the floor of Miyamoto crater by orbital spectroscopy, providing mineralogical evidence of past aqueous activity. Based on both the morphological and mineralogical evidence, Miyamoto crater represents an excellent site for in situ examination and sampling of a potentially habitable environment. ?? 2009 Elsevier Inc.

Effect of Organic Capping Layers over Monodisperse Platinum Nanoparticles upon Activity for Ethylene Hydrogenation and Carbon Monoxide Oxidation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kuhn, John N.; Tsung, Chia-Kuang; Huang, Wenyu

2009-03-24

The influence of oleylamine (OA), trimethyl tetradecyl ammonium bromide (TTAB), and polyvinlypyrrolidone (PVP) capping agents upon the catalytic properties of Pt/silica catalysts was evaluated. Pt nanoparticles that were 1.5 nm in size were synthesized by the same procedure (ethylene glycol reduction under basic conditions) with the various capping agents added afterward for stabilization. Before examining catalytic properties for ethylene hydrogenation and CO oxidation, the Pt NPs were deposited onto mesoporous silica (SBA-15) supports and characterized by transmission electron microscopy (TEM), H{sub 2} chemisorption, and elemental analysis (ICP-MS). PVP- and TTAB-capped Pt yielded mass-normalized reaction rates that decreased with increasing pretreatmentmore » temperature, and this trend was attributed to the partial coverage of the Pt surface with decomposition products from the organic capping agent. Once normalized to the Pt surface area, similar intrinsic activities were obtained regardless of the pretreatment temperature, which indicated no influence on the nature of the active sites. Consequently, a chemical probe technique using intrinsic activity for ethylene hydrogenation was demonstrated as an acceptable method for estimating the metallic surface areas of Pt. Amine (OA) capping exhibited a detrimental influence on the catalytic properties as severe deactivation and low activity were observed for ethylene hydrogenation and CO oxidation, respectively. These results were consistent with amine groups being strong poisons for Pt surfaces, and revealed the need to consider the effects of capping agents on the catalytic properties.« less

Chasma Boreale in the North Polar Region

NASA Technical Reports Server (NTRS)

2006-01-01

This images shows a Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) full-resolution 'targeted image' of the edge of Mars' north polar cap. The region in the image, Chasma Boreale, is a valley several kilometers or miles deep that cuts about 400 kilometers (about 250 miles) into the edge of the cap.

This image was acquired at 0851 UTC (4:51 a.m. EDT) on Oct. 1, 2006, near 84.6 degrees north latitude, 3.6 degrees east longitude. It covers an area about 13 kilometers (8 miles) long and, at the narrowest point, about 9 kilometers (5.6 miles) wide. At the center of the image the spatial resolution is as good as 18 meters (60 feet) per pixel. The image was taken in 544 colors covering wavelengths of 0.36 to 3.92 micrometers. Two renderings of the data are shown here, both draped over topography without vertical exaggeration, and then viewed from a perspective diagonally above the site. The top view is an approximately true-color representation. The bottom view, constructed from infrared wavelengths, shows strength of the spectral signature of ice. Brighter areas are rich in ice, and dark areas have little ice.

The polar cap has long been recognized to contain layers composed of dust and ice, and hence has been named the polar layered deposit. This sits atop an underlying 'basal unit.' The upper part of the basal unit is dark at visible wavelengths and steeply sloped, whereas the lower part of the basal unit is brighter, redder, and layered like the polar layered deposits. The chasma floor is cratered, and in the foreground it is covered by dunes that are outliers of a north polar sand sea that surrounds the polar cap. The polar layered deposits and the basal unit form a steeply sloping scarp about 1.1 kilometers (0.7 miles) high.

CRISM's image of this region shows a number of previously unrecognized characteristics of the polar layered deposits and the basal unit. First, the ice-rich polar layered deposits exhibit coherent banding both at visible and infrared wavelengths. This banding shows a history of differences in the abundance of dust that accumulated in polar ice, differences in ice grain size, or both. Second, both parts of the basal unit are depleted in ice, except for triangle-shaped regions on the side of the scarp. Third, the spectral properties of the brighter, layered lower basal unit resemble those of the polar layered deposits. In contrast, the upper basal unit is distinct from both of them. Finally, spectral properties of the foreground dunes closely resemble those of the darkest layers within the upper basal unit, and may be debris from it.

CRISM is one of six science instruments on NASA's Mars Reconnaissance Orbiter. Led by The Johns Hopkins University Applied Physics Laboratory, the CRISM team includes expertise from universities, government agencies and small businesses in the United States and abroad.

CRISM's mission: Find the spectral fingerprints of aqueous and hydrothermal deposits and map the geology, composition and stratigraphy of surface features. The instrument will also watch the seasonal variations in Martian dust and ice aerosols, and water content in surface materials -- leading to new understanding of the climate.

NASA's Jet Propulsion Laboratory, a division of the California Institute of Technology, Pasadena, manages the Mars Reconnaissance Orbiter mission for the NASA Science Mission Directorate. Lockheed Martin Space Systems, Denver, is the prime contractor and built the spacecraft.

Nocturnal cooling in a very shallow cold air pool

NASA Astrophysics Data System (ADS)

Rakovec, Jože; Skok, Gregor; Žabkar, Rahela; Žagar, Nedjeljka

2015-04-01

Cold air pools (CAPs) may develop during nights in very shallow depressions. The depth of the stagnant air within a CAP influences the process of the cooling of nocturnal air and the resulting minimum temperature. A seven-month long field experiment was performed during winter 2013/2014 in an orchard near Kr\\vsko, Slovenia, located inside a very shallow basin only a few meters deep and approximately 500 m wide. Two locations at different elevations inside the basin were selected for measurement. The results showed that the nights (in terms of cooling) can be classified into three main categories; nights with overcast skies and weak cooling, windy nights with clear sky and strong cooling but with no difference in temperatures between locations inside the basin, and calm nights with even stronger cooling and significant temperature differences between locations inside the basin. On calm nights with clear skies, the difference at two measuring sites inside the basin can be up to 5 °C but the presence of even weak winds can cause sufficient turbulent mixing to negate any difference in temperature. To better understand the cooling process on calm, clear nights, we developed a simple 1-D thermodynamic conceptual model focusing on a very shallow CAP. The model has 5-layers (including two air layers representing air inside the CAP), and an analytical solution was obtained for the equilibrium temperatures. Sensitivity analysis of the model was performed. As expected, a larger soil heat conductivity or higher temperature in the ground increases the morning minimum temperatures. An increase in temperature of the atmosphere also increases the simulated minimum temperatures, while the temperature difference between the higher and lower locations remains almost the same. An increase in atmosphere humidity also increases the modelled equilibrium temperatures, while an increase of the humidity of the air inside the CAP results in lower equilibrium temperatures. The humidity of the air within the CAP and that of the free atmosphere strongly influence the differences in equilibrium temperatures at higher and lower locations. The more humid the air, the stronger the cooling at the lower location compared to the higher location.

Aging-dependent DNA hypermethylation and gene expression of GSTM1 involved in T cell differentiation.

PubMed

Yeh, Shu-Hui; Liu, Cheng-Ling; Chang, Ren-Chieh; Wu, Chih-Chiang; Lin, Chia-Hsueh; Yang, Kuender D

2017-07-25

This study investigated whether aging was associated with epigenetic changes of DNA hypermethylation on immune gene expression and lymphocyte differentiation. We screened CG sites of methylation in blood leukocytes from different age populations, picked up genes with age-related increase of CG methylation content more than 15%, and validated immune related genes with CG hypermethylation involved in lymphocyte differentiation in the aged population. We found that 12 genes (EXHX1、 IL-10、 TSP50、 GSTM1、SLC5A5、SPI1、F2R、LMO2、PTPN6、FGFR2、MMP9、MET) were associated with promoter or exon one DNA hypermethylation in the aged group. Two immune related genes, GSTM1 and LMO2, were chosen to validate its aging-related CG hypermethylation in different leukocytes. We are the first to validate that GSTM1_P266 and LMO2_E128 CG methylation contents in T lymphocytes but not polymorphonuclear cells (PMNs) or mononuclear cells (MNCs) were significantly increased in the aged population. The GSTM1 mRNA expression in T lymphocytes but not PMNs or MNCs was inversely associated with the GSTM1 CG hypermethylation levels in the aged population studied. Further studies showed that lower GSTM1 CG methylation content led to the higher GSTM1 mRNA expression in T cells and knockdown of GSTM1 mRNA expression decreased type 1 T helper cell (Th1) differentiation in Jurkat T cells and normal adult CD4 T cells. The GSTM1_P266 hypermethylation in the aged population associated with lower GSTM1 mRNA expression was involved in Th1 differentiation, highlighting that modulation of aging-associated GSTM1 methylation may be able to enhance T helper cell immunity in the elders.

Tiny Device Mimics Human Lung Function

DOE Office of Scientific and Technical Information (OSTI.GOV)

McDonald, Rebecca; Harris, Jennifer; Nath, Pulak

Scientists at Los Alamos National Laboratory are developing a miniature, tissue-engineered artificial lung that mimics the response of the human lung to drugs, toxins and other agents. “We breathe in and out thousands of times every day. And while we have control over what we eat or drink, we don’t always have control over what we breathe in,” said Jennifer Harris of Biosecurity and Public Health at Los Alamos, "and so we’re making this miniature lung to be able to test on actual human cells whether something in the environment, or a drug, is toxic or harmful to us." Nicknamedmore » “PuLMo” for Pulmonary Lung Model (Pulmo is also the Latin word for "lung")the device consists of two major parts, the bronchiolar unit and the alveolar unit—just like the human lung. The units are primarily made from various polymers and are connected by a microfluidic “circuit board” that manages fluid and air flow. “When we build our lung, we not only take into account the aspects of different cell types, the tissues that are involved, we also take into account that a lung is supposed to breathe, so PuLMo actually breathes,” said Pulak Nath of Applied Modern Physics, who leads engineering efforts for the project. The most exciting application of PuLMo is a potentially revolutionary improvement in the reliability of drug-toxicity assessments and the prediction of new pharmaceutical success in humans, according to Harris. The PuLMo may also be designed to mimic lung disease conditions, such as Chronic Obstructive Pulmonary Disease (COPD) and asthma, and may be used to study lung air-flow dynamics to better understand the mechanisms of toxins and drug delivery and the effects of smoking, particularly the less-understood effects of e-cigarettes.« less

Remarkable lowering in the synthesis temperature of LiMn2O4via citrate solution-gel synthesis facilitated by ethanol.

PubMed

Maino, G; Carleer, R; Marchal, W; Bonneux, G; Hardy, A; Van Bael, M K

2017-11-07

LiMn 2 O 4 (LMO) is interesting from the viewpoint of its energy storage applications as it is a cathode in lithium ion batteries (LIB), which contains no rare, toxic or expansive elements, while it provides a high theoretical capacity (148 mA h g -1 ) at a reasonable voltage (4 V region) and a higher thermal stability compared to cobalt based cathodes and has a good rechargeability and cycling stability due to its spinel structure. Low temperature synthesis routes for cathode materials are currently gaining attention, in order to decrease the ecological footprint of the final LIB. Here, the crystallization temperature of LMO by a citrate based solution-gel synthesis was significantly lowered, to as low as 250 °C by the addition of ethanol to the precursor. The role of ethanol in this synthesis process was explored. It was found to lead to a considerable increase in the oxidation rate of the redox couple Mn 2+ /Mn 3+ , a lowering of the precursor decomposition temperature by 200 °C, besides a drastic decrease in the crystallization temperature (reaching 250 °C). Moreover, the main cause was identified to be an esterification reaction of ethanol with the carboxylic acid in the precursor complexes, taking place before the oxide formation. The insights obtained strengthen the knowledge regarding citrato-Mn 2+ /Mn 3+ complexes present in aqueous solution-gel synthesis routes and are relevant for the preparation of various manganese containing oxides. Moreover, the precursor developed opens up a new possibility for the low temperature synthesis of LMO powders and thin films for application in LIB. In the case of thin film batteries, the low temperature processing provides compatibility with other materials in the thin film battery stack, avoiding undesired oxidations or interfacial reactions.

Sims Analysis of Water Abundance and Hydrogen Isotope in Lunar Highland Plagioclase

NASA Technical Reports Server (NTRS)

Hui, Hejiu; Guan, Yunbin; Chen, Yang; Peslier, Anne H.; Zhang, Youxue; Liu, Yang; Rossman, George R.; Eiler, John M.; Neal, Clive R.

2015-01-01

The detection of indigenous water in mare basaltic glass beads has challenged the view established since the Apollo era of a "dry" Moon. Since this discovery, measurements of water in lunar apatite, olivine-hosted melt inclusions, agglutinates, and nominally anhydrous minerals have confirmed that lunar igneous materials contain water, implying that some parts of lunar mantle may have as much water as Earth's upper mantle. The interpretation of hydrogen (H) isotopes in lunar samples, however, is controversial. The large variation of H isotope ratios in lunar apatite (delta Deuterium = -202 to +1010 per mille) has been taken as evidence that water in the lunar interior comes from the lunar mantle, solar wind protons, and/or comets. The very low deuterium/H ratios in lunar agglutinates indicate that solar wind protons have contributed to their hydrogen content. Conversely, H isotopes in lunar volcanic glass beads and olivine-hosted melt inclusions being similar to those of common terrestrial igneous rocks, suggest a common origin for water in both Earth and Moon. Lunar water could be inherited from carbonaceous chondrites, consistent with the model of late accretion of chondrite-type materials to the Moon as proposed by. One complication about the sources of lunar water, is that geologic processes (e.g., late accretion and magmatic degassing) may have modified the H isotope signatures of lunar materials. Recent FTIR analyses have shown that plagioclases in lunar ferroan anorthosite contain approximately 6 ppm H2O. So far, ferroan anorthosite is the only available lithology that is believed to be a primary product of the lunar magma ocean (LMO). A possible consequence is that the LMO could have contained up to approximately 320 ppm H2O. Here we examine the possible sources of water in the LMO through measurements of water abundances and H isotopes in plagioclase of two ferroan anorthosites and one troctolite from lunar highlands.

Detecting Near-Surface Ice Formation Over Time Using the Kennaugh Elements Approach From TerraSAR-X

NASA Astrophysics Data System (ADS)

Fernandes, L.

2016-12-01

The summer melting has increased substantially at higher elevations on the Canadian Arctic ice caps. The resulting meltwater percolates into the upper layers of snow and firn and then refreeze, building massive ice bodies. It seems likely that these within-firn ice bodies now limit meltwater penetration into the firn and may be creating a feedback whereby the fraction of melt that runs off to the ocean is increasing. Although changes in firn structure as presence of ice layers and ice bodies are well documented over the Devon ice cap, the firm has shown that it exerts a crucial role to predict more accurately the contribution of small ice caps to the sea level rise. However it is still challenging to assess the extent of these features within the shallow subsurface using ice cores and GPR (Ground Penetrating Radar) data collected along a limited number of linear transects. Studying changes in the distribution of ice bodies' formation over time has the potential to provide information about how the growth of ice bodies in the firn is affecting the pattern of water flow in the firn layer. The objective is investigate the potential of Kennaugh Elements (KE) derived from x-band SAR (Synthetic Aperture Radar) for mapping the distribution and growth of large ice bodies within the firn and the evolution of their distribution over time. The evaluation of this method could reveal a new approach suitable for other glacierized regions that would reduce the costs and amount of field work for studying such properties.

A novel tomato mutant, Solanum lycopersicum elongated fruit1 (Slelf1), exhibits an elongated fruit shape caused by increased cell layers in the proximal region of the ovary.

PubMed

Chusreeaeom, Katarut; Ariizumi, Tohru; Asamizu, Erika; Okabe, Yoshihiro; Shirasawa, Kenta; Ezura, Hiroshi

2014-06-01

Genes controlling fruit morphology offer important insights into patterns and mechanisms determining organ shape and size. In cultivated tomato (Solanum lycopersicum L.), a variety of fruit shapes are displayed, including round-, bell pepper-, pear-, and elongate-shaped forms. In this study, we characterized a tomato mutant possessing elongated fruit morphology by histologically analyzing its fruit structure and genetically analyzing and mapping the genetic locus. The mutant line, Solanum lycopersicum elongated fruit 1 (Slelf1), was selected in a previous study from an ethylmethane sulfonate-mutagenized population generated in the background of Micro-Tom, a dwarf and rapid-growth variety. Histological analysis of the Slelf1 mutant revealed dramatically increased elongation of ovary and fruit. Until 6 days before flowering, ovaries were round and they began to elongate afterward. We also determined pericarp thickness and the number of cell layers in three designated fruit regions. We found that mesocarp thickness, as well as the number of cell layers, was increased in the proximal region of immature green fruits, making this the key sector of fruit elongation. Using 262 F2 individuals derived from a cross between Slelf1 and the cultivar Ailsa Craig, we constructed a genetic map, simple sequence repeat (SSR), cleaved amplified polymorphism sequence (CAPS), and derived CAPS (dCAPS) markers and mapped to the 12 tomato chromosomes. Genetic mapping placed the candidate gene locus within a 0.2 Mbp interval on the long arm of chromosome 8 and was likely different from previously known loci affecting fruit shape.

Retention of Electronic Conductivity in LaAlO3/SrTiO3 Nanostructures Using a SrCuO2 Capping Layer

NASA Astrophysics Data System (ADS)

Aurino, P. P.; Kalabukhov, A.; Borgani, R.; Haviland, D. B.; Bauch, T.; Lombardi, F.; Claeson, T.; Winkler, D.

2016-08-01

The interface between two wide band-gap insulators, LaAlO3 and SrTiO3 (LAO/STO) offers a unique playground to study the interplay and competitions between different ordering phenomena in a strongly correlated two-dimensional electron gas. Recent studies of the LAO/STO interface reveal the inhomogeneous nature of the 2DEG that strongly influences electrical-transport properties. Nanowires needed in future applications may be adversely affected, and our aim is, thus, to produce a more homogeneous electron gas. In this work, we demonstrate that nanostructures fabricated in the quasi-2DEG at the LaAlO3/SrTiO3 interface, capped with a SrCuO2 layer, retain their electrical resistivity and mobility independent of the structure size, ranging from 100 nm to 30 μ m . This is in contrast to noncapped LAO/STO structures, where the room-temperature electrical resistivity significantly increases when the structure size becomes smaller than 1 μ m . High-resolution intermodulation electrostatic force microscopy reveals an inhomogeneous surface potential with "puddles" of a characteristic size of 130 nm in the noncapped samples and a more uniform surface potential with a larger characteristic size of the puddles in the capped samples. In addition, capped structures show superconductivity below 200 mK and nonlinear current-voltage characteristics with a clear critical current observed up to 700 mK. Our findings shed light on the complicated nature of the 2DEG at the LAO/STO interface and may also be used for the design of electronic devices.

Control of surface topography in biomimetic calcium phosphate coatings.

PubMed

Costa, Daniel O; Allo, Bedilu A; Klassen, Robert; Hutter, Jeffrey L; Dixon, S Jeffrey; Rizkalla, Amin S

2012-02-28

The behavior of cells responsible for bone formation, osseointegration, and bone bonding in vivo are governed by both the surface chemistry and topography of scaffold matrices. Bone-like apatite coatings represent a promising method to improve the osteoconductivity and bonding of synthetic scaffold materials to mineralized tissues for regenerative procedures in orthopedics and dentistry. Polycaprolactone (PCL) films were coated with calcium phosphates (CaP) by incubation in simulated body fluid (SBF). We investigated the effect of SBF ion concentration and soaking time on the surface properties of the resulting apatite coatings. CaP coatings were examined by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectrometry (FTIR), and energy dispersive X-ray spectrometry (EDX). Young's modulus (E(s)) was determined by nanoindentation, and surface roughness was assessed by atomic force microscopy (AFM) and mechanical stylus profilometry. CaP such as carbonate-substituted apatite were deposited onto PCL films. SEM and AFM images of the apatite coatings revealed an increase in topographical complexity and surface roughness with increasing ion concentration of SBF solutions. Young's moduli (E(s)) of various CaP coatings were not significantly different, regardless of the CaP phase or surface roughness. Thus, SBF with high ion concentrations may be used to coat synthetic polymers with CaP layers of different surface topography and roughness to improve the osteoconductivity and bone-bonding ability of the scaffold. © 2012 American Chemical Society

Multi-MICE: Nuclear Powered Mobile Probes to Explore Deep Interiors of the Ice Sheets on Mars and the Jovian Moons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maise, George; Powell, James; Paniagua, John

2007-01-30

The multi-kilometer thick Polar Caps on Mars contain unique and important data about the multi-million year history of its climate, geology, meteorology, volcanology, cosmic ray and solar activity, and meteor impacts. They also may hold evidence of past life on Mars, including microbes, microfossils and biological chemicals. The objective of this paper is to describe a probe that can provide access to the data locked in the Polar Caps. The MICE (Mars Ice Cap Explorer) system would explore the Polar Cap interiors using mobile probes powered by compact, lightweight nuclear reactors. The probes would travel 100's of meters per daymore » along melt channels in the ice sheets created by hot water jets from the 500 kW(th) nuclear reactors, ascending and descending, either vertically or at an angle to the vertical, reaching bedrock at kilometers beneath the surface. The powerful reactor will be necessary to provide sufficient hot water at high velocity to penetrate the extensive horizontal dust/sand layers that separate layers of ice in the Mars Ice Caps. MICE reactors can operate at 500 kW(th) for more than 4 years, and much longer in practice, since power level will be much lower when the probes are investigating locations in detail at low or zero speed. Multiple probes, e.g. six, would be deployed in an interactive network, continuously communicating by RF and acoustic signals with each other and with the surface lander spacecraft. In turn, the lander would continuously communicate in real time, subject to speed of light delays, with scientists on Earth to transmit data and receive instructions for the MICE probes. Samples collected by the probes could be brought to the lander, for return to the Earth at the end of the mission.« less

Uncooled thin film pyroelectric IR detector with aerogel thermal isolation

DOEpatents

Ruffner, Judith A.; Bullington, Jeff A.; Clem, Paul G.; Warren, William L.; Brinker, C. Jeffrey; Tuttle, Bruce A.; Schwartz, Robert W.

1999-01-01

A monolithic infrared detector structure which allows integration of pyroelectric thin films atop low thermal conductivity aerogel thin films. The structure comprises, from bottom to top, a substrate, an aerogel insulating layer, a lower electrode, a pyroelectric layer, and an upper electrode layer capped by a blacking layer. The aerogel can offer thermal conductivity less than that of air, while providing a much stronger monolithic alternative to cantilevered or suspended air-gap structures for pyroelectric thin film pixel arrays. Pb(Zr.sub.0.4 Ti.sub.0.6)O.sub.3 thin films deposited on these structures displayed viable pyroelectric properties, while processed at 550.degree. C.

Effect of nano oxide layer on exchange bias and GMR in Mn-Ir-Pt based spin valve

NASA Astrophysics Data System (ADS)

Jeon, D. M.; Lee, J. P.; Lee, D. H.; Yoon, S. Y.; Kim, Y. S.; Suh, S. J.

2004-05-01

We have investigated the effect of nano oxide layers (NOLs), which were fabricated by a plasma oxidation of CoFe layer on the magnetic properties and magneto-resistance (MR) in a Mn-Ir-Pt based spin valve. The adjusted NOL could result in the high MR and the strong exchange coupling field ( Hex). From a high resolution electron microscopy analysis the oxide was about 1 nm. The strong reflectivity at the interface of a free and oxide capping layer should lead to the decrease of an interlayer coupling field, which could possibly improve the Hex.

Improved photoluminescence quantum yield and stability of CdSe-TOP, CdSe-ODA-TOPO, CdSe/CdS and CdSe/EP nanocomposites

NASA Astrophysics Data System (ADS)

Wei, Shutian; Zhu, Zhilin; Wang, Zhixiao; Wei, Gugangfen; Wang, Pingjian; Li, Hai; Hua, Zhen; Lin, Zhonghai

2016-07-01

Size-controllable monodisperse CdSe nanocrystals with different organic capping were prepared based on the hot-injection method. The effective separation of nucleation and growth was achieved by rapidly mixing two highly reactive precursors. As a contrast, we prepared CdSe/CdS nanocrystals (NCs) successfully based on the selective ion layer adsorption and reaction (SILAR) technique. This inorganic capping obtained higher photoluminescence quantum yield (PLQY) of 59.3% compared with organic capping of 40.8%. Furthermore, the CdSe-epoxy resin (EP) composites were prepared by adopting a flexible ex situ method, and showed excellent stability in the ambient environment for one year. So the composites with both high PLQY of nanocrystals and excellent stability are very promising to device application.

Albedo models for the residual south polar cap on Mars: Implications for the stability of the cap under near-perihelion global dust storm conditions

NASA Astrophysics Data System (ADS)

Bonev, Boncho P.; Hansen, Gary B.; Glenar, David A.; James, Philip B.; Bjorkman, Jon E.

2008-02-01

It is uncertain whether the residual (perennial) south polar cap on Mars is a transitory or a permanent feature in the current Martian climate. While there is no firm evidence for complete disappearance of the cap in the past, clearly observable changes have been documented. Observations suggest that the perennial cap lost more CO 2 material in the spring/summer season prior to the Mariner 9 mission than in those same seasons monitored by Viking and Mars Global Surveyor. In this paper we examine one process that may contribute to these changes - the radiative effects of a planet encircling dust storm that starts during late Martian southern spring on the stability of the perennial south polar cap. To approach this, we model the radiative transfer through a dusty planetary atmosphere bounded by a sublimating CO 2 surface. A critical parameter for this modeling is the surface albedo spectrum from the near-UV to the thermal-IR, which was determined from both space-craft and Earth-based observations covering multiple wavelength regimes. Such a multi-wavelength approach is highly desirable since one spectral band by itself cannot tightly constrain the three-parameter space for polar surface albedo models, namely photon "scattering length" in the CO 2 ice and the amounts of intermixed water and dust. Our results suggest that a planet-encircling dust storm with onset near solstice can affect the perennial cap's stability, leading to advanced sublimation in a "dusty" year. Since the total amount of solid CO 2 removed by a single storm may be less than the total CO 2 thickness, a series of dust storms would be required to remove the entire residual CO 2 ice layer from the south perennial cap.

Content and bioconcentration of mercury in mushrooms from northern Poland.

PubMed

Falandysz, J; Gucia, M; Brzostowski, A; Kawano, M; Bielawski, L; Frankowska, A; Wyrzykowska, B

2003-03-01

Mercury (Hg) was quantified using cold vapour-atomic absorption spectrometry (CV-AAS) in the fruiting bodies of nine edible and five inedible mushrooms and in underlying soil substrate samples. In total, 404 samples comprising caps and stalks and 202 samples of soil substrate (0-10 cm layer) were collected in 1996 from Trójmiejski Landscape Park, northern Poland. Mean Hg concentrations in the soil substrate for different species varied between 10 +/- 3 and 780 +/- 500 ng x g(-1) dry wt (range 2.3-1700). Among edible mushroom species, Horse Mushroom (Agaricus arvensis), Brown Birch Scaber Stalk (Leccinum scabrum), Parasol Mushroom (Macrolepiota procera), King Bolete (Boletus edulis) and Yellow-cracking Bolete (Xerocomus subtomentosus) contained elevated concentrations of Hg ranging from 1600 +/- 930 to 6800 +/- 4000 ng x g(-1) dry wt in the caps. Concentrations of Hg in the stalks were 2.6 +/- 1.1 to 1.7 +/- 1.0 times lower than those in the caps. Some mushroom species investigated had high Hg levels when compared with specimens collected from the background reference sites elsewhere (located far away from the big cities) in northern Poland. Bioconcentration factors of Hg in the caps of Horse Mushroom, Parasol Mushroom and Brown Birch Scaber Stalk were between 150 +/- 58 and 230 +/- 150 ng x g(-1) dry wt, respectively, and for inedible Pestle-shaged Puffball (Claviata excipulformis) was 960 +/- 300 ng x g(-1) dry wt. Linear regression coefficients between Hg in caps and in stalks and Hg soil concentrations showed a positive relationship for A. arvensis and Horse mushroom (p < 0.05) and a negative correlation for the caps of Death Caps (Amanita phalloides) and Woolly Milk Cap (Lactarius torminosus) (p < 0.05), while for other species no clear trend was found.

The Nuclear Family: Correspondence in Cognitive and Affective Reactions to the Threat of Nuclear War among Older Adolescents and Their Parents.

ERIC Educational Resources Information Center

Hamilton, Scott B.; And Others

1986-01-01

In order to assess the relationship between family members' cognitive and affective responses to nuclear war issues, 317 college students and their parents independently completed a multifaceted questionnaire that included items concerning personal reactions, predictions, opinions, and attitudes about nuclear war. (Author/LMO)

The little ice age as recorded in the stratigraphy of the tropical quelccaya ice cap.

PubMed

Thompson, L G; Mosley-Thompson, E; Dansgaard, W; Grootes, P M

1986-10-17

The analyses of two ice cores from a southern tropical ice cap provide a record of climatic conditions over 1000 years for a region where other proxy records are nearly absent. Annual variations in visible dust layers, oxygen isotopes, microparticle concentrations, conductivity, and identification of the historical (A.D. 1600) Huaynaputina ash permit accurate dating and time-scale verification. The fact that the Little Ice Age (about A.D. 1500 to 1900) stands out as a significant climatic event in the oxygen isotope and electrical conductivity records confirms the worldwide character of this event.

Biocompatible Nanocoatings of Fluorinated Polyphosphazenes through Aqueous Assembly

DOE PAGES

Selin, Victor; Albright, Victoria; Ankner, John Francis; ...

2018-02-23

Nonionic fluorinated polyphosphazenes, such as poly[bis(trifluoroethoxy)phosphazene] (PTFEP), display superb biocompatibility, yet their deposition to surfaces has been limited to solution casting from organic solvents or thermal molding. Here in this paper, hydrophobic coatings of fluorinated polyphosphazenes are demonstrated through controlled deposition of ionic fluorinated polyphosphazenes (iFPs) from aqueous solutions using the layer-by-layer (LbL) technique. Specifically, the assemblies included poly[(carboxylatophenoxy)(trifluoroethoxy)phosphazenes] with varied content of fluorine atoms as iFPs (or poly[bis(carboxyphenoxy)phosphazene] (PCPP) as a control nonfluorinated polyphosphazene) and a variety of polycations. Hydrophobic interactions largely contributed to the formation of LbL films of iFPs with polycations, leading to linear growth and extremelymore » low water uptake. Hydrophobicity-enhanced ionic pairing within iFP/BPEI assemblies gave rise to large-amplitude oscillations in surface wettability as a function of capping layer, which were the largest for the most fluorinated iFP, while control PCPP/polycation systems remained hydrophilic regardless of the film top layer. Neutron reflectometry (NR) studies indicated superior layering and persistence of such layering in salt solution for iFP/BPEI films as compared to control PCPP/polycation systems. Hydrophobicity of iFP-capped LbL coatings could be further enhanced by using a highly porous polyester surgical felt rather than planar substrates for film deposition. Importantly, iFP/polycation coatings displayed biocompatibility which was similar to or superior to that of solution-cast coatings of a clinically validated material (PTFEP), as demonstrated by the hemolysis of the whole blood and protein adsorption studies.« less

Biocompatible Nanocoatings of Fluorinated Polyphosphazenes through Aqueous Assembly

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selin, Victor; Albright, Victoria; Ankner, John Francis

Nonionic fluorinated polyphosphazenes, such as poly[bis(trifluoroethoxy)phosphazene] (PTFEP), display superb biocompatibility, yet their deposition to surfaces has been limited to solution casting from organic solvents or thermal molding. Here in this paper, hydrophobic coatings of fluorinated polyphosphazenes are demonstrated through controlled deposition of ionic fluorinated polyphosphazenes (iFPs) from aqueous solutions using the layer-by-layer (LbL) technique. Specifically, the assemblies included poly[(carboxylatophenoxy)(trifluoroethoxy)phosphazenes] with varied content of fluorine atoms as iFPs (or poly[bis(carboxyphenoxy)phosphazene] (PCPP) as a control nonfluorinated polyphosphazene) and a variety of polycations. Hydrophobic interactions largely contributed to the formation of LbL films of iFPs with polycations, leading to linear growth and extremelymore » low water uptake. Hydrophobicity-enhanced ionic pairing within iFP/BPEI assemblies gave rise to large-amplitude oscillations in surface wettability as a function of capping layer, which were the largest for the most fluorinated iFP, while control PCPP/polycation systems remained hydrophilic regardless of the film top layer. Neutron reflectometry (NR) studies indicated superior layering and persistence of such layering in salt solution for iFP/BPEI films as compared to control PCPP/polycation systems. Hydrophobicity of iFP-capped LbL coatings could be further enhanced by using a highly porous polyester surgical felt rather than planar substrates for film deposition. Importantly, iFP/polycation coatings displayed biocompatibility which was similar to or superior to that of solution-cast coatings of a clinically validated material (PTFEP), as demonstrated by the hemolysis of the whole blood and protein adsorption studies.« less

Capping Layer (CL) Induced Antidamping in CL/Py/β-W System (CL: Al, β-Ta, Cu, β-W).

PubMed

Behera, Nilamani; Guha, Puspendu; Pandya, Dinesh K; Chaudhary, Sujeet

2017-09-13

For achieving ultrafast switching speed and minimizing dissipation losses, the spin-based data storage device requires a control on effective damping (α eff ) of nanomagnetic bits. Incorporation of interfacial antidamping spin orbit torque (SOT) in spintronic devices therefore has high prospects for enhancing their performance efficiency. Clear evidence of such an interfacial antidamping is found in Al capped Py(15 nm)/β-W(t W )/Si (Py = Ni 81 Fe 19 and t W = thickness of β-W), which is in contrast to the increase of α eff (i.e., damping) usually associated with spin pumping as seen in Py(15 nm)/β-W(t W )/Si system. Because of spin pumping, the interfacial spin mixing conductance (g ↑↓ ) at Py/β-W interface and spin diffusion length (λ SD ) of β-W are found to be 1.63(±0.02) × 10 18 m -2 (1.44(±0.02) × 10 18 m -2 ) and 1.42(±0.19) nm (1.00(±0.10) nm) for Py(15 nm)/β-W(t W )/Si (β-W(t W )/Py(15 nm)/Si) bilayer systems. Other different nonmagnetic capping layers (CL), namely, β-W(2 nm), Cu(2 nm), and β-Ta(2,3,4 nm) were also grown over the same Py(15 nm)/β-W(t W ). However, antidamping is seen only in β-Ta(2,3 nm)/Py(15 nm)/β-W(t W )/Si. This decrease in α eff is attributed to the interfacial Rashba like SOT generated by nonequilibrium spin accumulation subsequent to the spin pumping. Contrary to this, when interlayer positions of Py(15 nm) and β-W(t W ) is interchanged irrespective of the fixed top nonmagnetic layer, an increase of α eff is observed, which is ascribed to spin pumping from Py to β-W layer.

Three-dimensional radar imaging of structures and craters in the Martian polar caps.

PubMed

Putzig, Nathaniel E; Smith, Isaac B; Perry, Matthew R; Foss, Frederick J; Campbell, Bruce A; Phillips, Roger J; Seu, Roberto

2018-07-01

Over the last decade, observations acquired by the Shallow Radar (SHARAD) sounder on individual passes of the Mars Reconnaissance Orbiter have revealed the internal structure of the Martian polar caps and provided new insights into the formation of the icy layers within and their relationship to climate. However, a complete picture of the cap interiors has been hampered by interfering reflections from off-nadir surface features and signal losses associated with sloping structures and scattering. Foss et al. (2017) addressed these limitations by assembling three-dimensional data volumes of SHARAD observations from thousands of orbital passes over each polar region and applying geometric corrections simultaneously. The radar volumes provide unprecedented views of subsurface features, readily imaging structures previously inferred from time-intensive manual analysis of single-orbit data (e.g., trough-bounding surfaces, a buried chasma, and a basal unit in the north, massive carbon-dioxide ice deposits and discontinuous layered sequences in the south). Our new mapping of the carbon-dioxide deposits yields a volume of 16,500 km 3 , 11% larger than the prior estimate. In addition, the radar volumes newly reveal other structures, including what appear to be buried impact craters with no surface expression. Our first assessment of 21 apparent craters at the base of the north polar layered deposits suggests a Hesperian age for the substrate, consistent with that of the surrounding plains as determined from statistics of surface cratering rates. Planned mapping of similar features throughout both polar volumes may provide new constraints on the age of the icy layered deposits. The radar volumes also provide new topographic data between the highest latitudes observed by the Mars Orbiter Laser Altimeter and those observed by SHARAD. In general, mapping of features in these radar volumes is placing new constraints on the nature and evolution of the polar deposits and associated climate changes.

Three-dimensional radar imaging of structures and craters in the Martian polar caps

NASA Astrophysics Data System (ADS)

Putzig, Nathaniel E.; Smith, Isaac B.; Perry, Matthew R.; Foss, Frederick J.; Campbell, Bruce A.; Phillips, Roger J.; Seu, Roberto

2018-07-01

Over the last decade, observations acquired by the Shallow Radar (SHARAD) sounder on individual passes of the Mars Reconnaissance Orbiter have revealed the internal structure of the Martian polar caps and provided new insights into the formation of the icy layers within and their relationship to climate. However, a complete picture of the cap interiors has been hampered by interfering reflections from off-nadir surface features and signal losses associated with sloping structures and scattering. Foss et al. (The Leading Edge 36, 43-57, 2017, https://doi.org/10.1190/tle36010043.1) addressed these limitations by assembling three-dimensional data volumes of SHARAD observations from thousands of orbital passes over each polar region and applying geometric corrections simultaneously. The radar volumes provide unprecedented views of subsurface features, readily imaging structures previously inferred from time-intensive manual analysis of single-orbit data (e.g., trough-bounding surfaces, a buried chasma, and a basal unit in the north, massive carbon-dioxide ice deposits and discontinuous layered sequences in the south). Our new mapping of the carbon-dioxide deposits yields a volume of 16,500 km3, 11% larger than the prior estimate. In addition, the radar volumes newly reveal other structures, including what appear to be buried impact craters with no surface expression. Our first assessment of 21 apparent craters at the base of the north polar layered deposits suggests a Hesperian age for the substrate, consistent with that of the surrounding plains as determined from statistics of surface cratering rates. Planned mapping of similar features throughout both polar volumes may provide new constraints on the age of the icy layered deposits. The radar volumes also provide new topographic data between the highest latitudes observed by the Mars Orbiter Laser Altimeter and those observed by SHARAD. In general, mapping of features in these radar volumes is placing new constraints on the nature and evolution of the polar deposits and associated climate changes.

The role of titanium aluminide in n-gallium nitride ohmic contact technology

NASA Astrophysics Data System (ADS)

Pelto, Christopher M.

Ohmic contacts are essential to the realization of efficient and affordable nitride-based electronic and optoelectronic devices. Currently, the most successful ohmic contact schemes to n-GaN are based on the Al/Ti bilayer structure, although the mechanism responsible for the low resistance in these contacts is not sufficiently understood. In this work, the intermetallic TiAl3 has been employed both as a model ohmic contact system to help understand the essential features of the Al/Ti standard contact, as well as a thermally stable oxidation cap for the bilayer structure. A quaternary isotherm of the Al-Ti-Ga-N system was calculated at 600°C, which showed that a sufficient phase topology was present to apply the exchange mechanism to the TiAl 3/GaN couple. The exchange mechanism rationalized the selection of the TiAl3 intermetallic by predicting that an Al-rich AlGaN layer will form at the metal/semiconductor interface. As part of the investigation of these novel contact systems, a thorough characterization was undertaken on both a standard Al/Ti and Au/Ni/Al/Ti contact to n-GaN in which the essential processing parameters and metallurgical properties were identified. The TiAl 3 contact was found to exhibit inferior electrical behavior compared to the Al/Ti bilayer, requiring significantly higher annealing temperatures to achieve comparable specific contact resistance. It is conjectured that this is due to the early formation of a TiN layer at the metal/semiconductor interface of the bilayer contact, even though both contacts are suspected to form the Al-rich nitride layer at higher temperature. As an oxidation cap, the TiAl3 metallization was found to provide much improved performance characteristics compared to the four-layer Au/Al/Ni/Ti standard. The TiAl 3/Al/Ti contact proved to achieve optimal performance at a much lower temperature than the standard, and furthermore showed complete insensitivity to the oxidation content of the annealing ambient. Reaction mechanisms for the TiAl3-capped and the four-layer contact metallizations are suggested that account for both the morphology and the expected interfacial phases of each system.

Stereo Topography of the South Polar of Mar: Volatile Inventory and Mars Polar Landing Landing Site

NASA Technical Reports Server (NTRS)

Schenk, Paul M.; Moore, Jeffrey M.

2000-01-01

Viking stereo images and topographic maps reveal that the south polar layered deposits of Mars are topographically complex and morphologically distinct from the north polar layered deposits. The dominant feature is a 500-km-wide topographic dome that rises 3 km above the surrounding plains. This dome underlies the residual ice cap but is at least 50% larger in area. Erosional scarps and terraces indicate that this dome was once more extensive and has undergone erosional retreat. Adjacent to the dome, layered deposits form a vast plateau 1-1.5 km high extending approximately 1000 km beyond and to one side of the residual south polar cap. This plateau is relatively flat at kilometer scales, although it is cut in places by troughs and depressions, which have locally steep scarps up to 2 km high and sloping up to roughly 10 deg. Contiguously flat kilometer-scale regions the size of the Mars Polar Lander (MPL) landing ellipse are present. These are in the form of plateaus 100-300 km wide and 1-2 km high. One of the largest of these plateaus has been proposed as a landing site for the Mars Polar Lander (MPL). The volume associated with the south polar layered deposits may be comparable to those of the layered deposits at the north pole. Although this doubles the current probable inventory of surface ice on Mars, it still falls far short of accounting for the inferred volume of water on Mars in the past.

On the role of electric field direction in the formation of sporadic E-layers in the southern polar cap ionosphere

NASA Astrophysics Data System (ADS)

Parkinson, M. L.; Dyson, P. L.; Monselesan, D. P.; Morris, R. J.

1998-03-01

Measurements of the occurrence of sporadic E (Es)-layers and F-region electric fields were obtained with a modern, HF digital ionosonde located at Casey, Antarctica (66.3°S, 110.5°E, 81°S CGM latitude) during the late austral summer of 1995/96. The occurrence of Es-layers was inferred from the presence of appropriate traces in normal swept-frequency ionograms, and the electric fields were inferred from F-region ``drift-mode'' velocities assuming that the plasma convection velocities given by E × B/B2 were measured, on average, by the interferometer. The theory of formation of high-latitude Es-layers predicts that electric fields directed toward the south west (SW) should be particularly effective at producing thin layers in the southern hemisphere. Our measurements made at a true polar cap station are consistent with this expectation, and are contrasted with observations made by incoherent scatter radars in the northern hemisphere, which also show the importance of SW electric fields, whereas the same theory predicts that NW electric fields should be important at northern latitudes. We reconcile the interhemispheric differences with simple calculations of ion convergence driven by the electric fields specified by the IZMIRAN electrodynamic model (IZMEM) in both hemispheres. The importance of the interplanetary magnetic field in the control of high-latitude Es formation is emphasised as an important adjunct to space weather modelling and forecasting.

More South Polar 'Swiss Cheese'

NASA Technical Reports Server (NTRS)

2000-01-01

This image is illuminated by sunlight from the upper left.

Some of the surface of the residual south polar cap has a pattern that resembles that of sliced, swiss cheese. Shown here at the very start of southern spring is a frost-covered surface in which there are two layers evident--a brighter upper layer into which are set swiss cheese-like holes, and a darker, lower layer that lies beneath the 'swiss cheese' pattern. Nothing like this exists anywhere on Mars except within the south polar cap.

This is a Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image acquired on August 2,1999. It is located near 84.8oS, 71.8oW, and covers an area 3 km across and about 6.1 km long (1.9 by 3.8 miles).

Malin Space Science Systems and the California Institute of Technology built the MOC using spare hardware from the Mars Observer mission. MSSS operates the camera from its facilities in San Diego, CA. The Jet Propulsion Laboratory's Mars Surveyor Operations Project operates the Mars Global Surveyor spacecraft with its industrial partner, Lockheed Martin Astronautics, from facilities in Pasadena, CA and Denver, CO.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vanheusden, K.; Warren, W.L.; Devine, R.A.B.

It is shown how mobile H{sup +} ions can be generated thermally inside the oxide layer of Si/SiO{sub 2}/Si structures. The technique involves only standard silicon processing steps: the nonvolatile field effect transistor (NVFET) is based on a standard MOSFET with thermally grown SiO{sub 2} capped with a poly-silicon layer. The capped thermal oxide receives an anneal at {approximately}1100 C that enables the incorporation of the mobile protons into the gate oxide. The introduction of the protons is achieved by a subsequent 500-800 C anneal in a hydrogen-containing ambient, such as forming gas (N{sub 2}:H{sub 2} 95:5). The mobile protonsmore » are stable and entrapped inside the oxide layer, and unlike alkali ions, their space-charge distribution can be controlled and rapidly rearranged at room temperature by an applied electric field. Using this principle, a standard MOS transistor can be converted into a nonvolatile memory transistor that can be switched between normally on and normally off. Switching speed, retention, endurance, and radiation tolerance data are presented showing that this non-volatile memory technology can be competitive with existing Si-based non-volatile memory technologies such as the floating gate technologies (e.g. Flash memory).« less

Low-Noise Large-Area Photoreceivers with Low Capacitance Photodiodes

NASA Technical Reports Server (NTRS)

Joshi, Abhay M. (Inventor); Datta, Shubhashish (Inventor)

2013-01-01

A quad photoreceiver includes a low capacitance quad InGaAs p-i-n photodiode structure formed on an InP (100) substrate. The photodiode includes a substrate providing a buffer layer having a metal contact on its bottom portion serving as a common cathode for receiving a bias voltage, and successive layers deposited on its top portion, the first layer being drift layer, the second being an absorption layer, the third being a cap layer divided into four quarter pie shaped sections spaced apart, with metal contacts being deposited on outermost top portions of each section to provide output terminals, the top portions being active regions for detecting light. Four transimpedance amplifiers have input terminals electrically connected to individual output terminals of each p-i-n photodiode.

Pilot project for maximum heat of mass concrete.

DOT National Transportation Integrated Search

2013-04-01

A 3-D finite element model was developed for prediction of early age behavior of mass concrete footing placed on a soil layer. Three bridge pier footings and one bridge pier cap in Florida were monitored for temperature development. The measured temp...

Buried CO2 Ice traces in South Polar Layered Deposits of Mars detected by radar sounder

NASA Astrophysics Data System (ADS)

Castaldo, L.; Mège, D.; Orosei, R.; Séjourné, A.

2014-12-01

SHARAD (SHAllow RADar) is the subsurface sounding radar provided by the Italian Space Agency (ASI) as a facility instrument to NASA's 2005 Mars Reconnaissance Orbiter (MRO). The Reduced Data Record of SHARAD data covering the area of the South Polar Layered Deposits (SPLD), has been used. The elaboration and interpretation of the data, aimed to estimate electromagnetic properties of surface layers, has been performed in terms of permittivity. The theory of electromagnetic scattering from fractal surfaces, and the estimation of geometric parameters from topographic data by Mars Orbiter Laser Altimeter (MOLA) which was one of five instruments on board the Mars Global Surveyor (MGS) spacecraft, has been used. A deep analysis of inversion has been made on all Mars and extended to the South Polar Caps in order to extract the area with a permittivity constant of CO2 ice. Several corrections have been applied to the data, moreover the calibration of the signal requires the determination of a constant that takes into account the power gain due to the radar system and the surface in order to compensate the power losses due to the orbitographic phenomena. The determination of regions with high probability of buried CO2 ice in the first layer of the Martian surface, is obtained extracting the real part of the permittivity constant of the CO2 ice (~2), estimated by other means. The permittivity of CO2ice is extracted from the Global Permittivity Map of Mars using the global standard deviation of itself as following: ɛCO2ice=ɛCO2ice+ Σ (1)where Σ=±std(ɛMapMars)/2Figure 1(a) shows the south polar areas where the values of the permittivity point to the possibility of a CO2 ice layer. Figure 1(b) is the corresponding geologic map. The comparison between the two maps indicates that the area with probable buried CO2 overlaps Hesperian and Amazonian polar units (Hp, Hesperian plains-forming deposits marked by narrow sinuous, anabranching ridges and irregular depressions, and Apu, Amazonian layered plateaus). From this analysis, the south polar cap could be covered by a thin frozen carbon dioxide coating. The perennial south polar cap is probably made of frozen carbon dioxide ca. 8 meters thick.

Carbon Nanotubes: On the Origin of Helicity

NASA Astrophysics Data System (ADS)

Harutyunyan, Avetik

2015-03-01

The mechanism of helicity formation of carbon nanotubes still remains elusive that hinders their applications. Current explanations mainly rely on the planar interrelationship between the structure of nanotube and corresponding facet of catalyst in 2D geometry that could amend the structure of grown carbon layer, specifically due to the epitaxial interaction. Yet, the structure of carbon nanotube and circumference of the rims assume involvement of more than one facet i.e. it is 3D problem. By aiming this problem we find that the nanotube nucleation is initiated by cap formation via evolving of graphene embryo across the adjacent facets of catalyst particle. As a result the graphene embryos incorporate in their hexagonic network various polygons to accommodate the curved 3D geometry that initiates cap formation following by elongation of the circumferential rims. Based on these results, also on the census of nanotube caps and the fact that given cap fit only one nanotube wall, we consider carbon cap responsible for the helicity of carbon nanotube. This understanding could provide new avenues towards engineering particles to explicitly accommodate certain helicities via exploitation of the angular distribution of catalyst adjacent facets. Our recent progresses in production of carbon nanotubes, nanotube reinforced composites and their potential applications also will be presented.

Model for capping of membrane receptors based on boundary surface effects

PubMed Central

Gershon, N. D.

1978-01-01

Crosslinking of membrane surface receptors may lead to their segregation into patches and then into a single large aggregate at one pole of the cell. This process is called capping. Here, a novel explanation of such a process is presented in which the membrane is viewed as a supersaturated solution of receptors in the lipid bilayer and the adjacent two aqueous layers. Without a crosslinking agent, a patch of receptors that is less than a certain size cannot stay in equilibrium with the solution and thus should dissolve. Patches greater than a certain size are stable and can, in principle, grow by the precipitation of the remaining dissolved receptors from the supersaturated solution. The task of the crosslinking molecules is to form such stable patches. These considerations are based on a qualitative thermodynamic calculation that takes into account the existence of a boundary tension in a patch (in analogy to the surface tension of a droplet). Thermodynamically, these systems should cap spontaneously after the patches have reached a certain size. But, in practice, such a process can be very slow. A suspension of patches may stay practically stable. The ways in which a cell may abolish this metastable equilibrium and thus achieve capping are considered and possible effects of capping inhibitors are discussed. PMID:274724

Mars South Polar Cap "Fingerprint" Terrain

NASA Image and Video Library

2000-04-24

This picture is illuminated by sunlight from the upper left. Some portions of the martian south polar residual cap have long, somewhat curved troughs instead of circular pits. These appear to form in a layer of material that may be different than that in which "swiss cheese" circles and pits form, and none of these features has any analog in the north polar cap or elsewhere on Mars. This picture shows the "fingerprint" terrain as a series of long, narrow depressions considered to have formed by collapse and widening by sublimation of ice. Unlike the north polar cap, the south polar region stays cold enough in summer to retain frozen carbon dioxide. Viking Orbiter observations during the late 1970s showed that very little water vapor comes off the south polar cap during summer, indicating that any frozen water that might be there remains solid throughout the year. This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image was obtained in early southern spring on August 4, 1999. It shows an area 3 x 5 kilometers (1.9 x 3.1 miles) at a resolution of about 7.3 meters (24 ft) per pixel. Located near 86.0°S, 53.9°W. http://photojournal.jpl.nasa.gov/catalog/PIA02373

Effect of thin oxide layers incorporated in spin valve structures

NASA Astrophysics Data System (ADS)

Gillies, M. F.; Kuiper, A. E. T.; Leibbrandt, G. W. R.

2001-06-01

The enhancement of the magnetoresistance effect, induced by incorporating nano-oxide layers (NOLs) in a bottom-type spin valve, was studied for various preparation conditions. The effect of a NOL in the Co90Fe10 pinned layer was found to depend critically on the oxygen pressure applied to form the thin oxide film. Pressures over 10-3 Torr O2 yield oxides thicker than about 0.7 nm, which apparently deteriorate the biasing field which exists over the oxide. The magnetoresistance values can further be raised by forming a specular reflecting oxide on top of the sense layer. Promising results were obtained with an Al2O3 capping layer formed in a solid-state oxidation reaction that occurs spontaneously when a thin Al layer is deposited on the oxidized surface of the Co90Fe10 sense layer.

Sputtering growth of Y3Fe5O12/Pt bilayers and spin transfer at Y3Fe5O12/Pt interfaces

NASA Astrophysics Data System (ADS)

Chang, Houchen; Liu, Tao; Reifsnyder Hickey, Danielle; Janantha, P. A. Praveen; Mkhoyan, K. Andre; Wu, Mingzhong

2017-12-01

For the majority of previous work on Y3Fe5O12 (YIG)/normal metal (NM) bi-layered structures, the YIG layers were grown on Gd3Ga5O12 first and were then capped by an NM layer. This work demonstrates the sputtering growth of a Pt/YIG structure where the Pt layer was grown first and the YIG layer was then deposited on the top. The YIG layer shows well-oriented (111) texture, a surface roughness of 0.15 nm, and an effective Gilbert damping constant less than 4.7 × 10-4, and the YIG/Pt interface allows for efficient spin transfers. This demonstration indicates the feasibility of fabricating high-quality NM/YIG/NM tri-layered structures for new physics studies.

A solar escalator on Mars: Self-lifting of dust layers by radiative heating

NASA Astrophysics Data System (ADS)

Daerden, F.; Whiteway, J. A.; Neary, L.; Komguem, L.; Lemmon, M. T.; Heavens, N. G.; Cantor, B. A.; Hébrard, E.; Smith, M. D.

2015-09-01

Dust layers detected in the atmosphere of Mars by the light detection and ranging (LIDAR) instrument on the Phoenix Mars mission are explained using an atmospheric general circulation model. The layers were traced back to observed dust storm activity near the edge of the north polar ice cap where simulated surface winds exceeded the threshold for dust lifting by saltation. Heating of the atmospheric dust by solar radiation caused buoyant instability and mixing across the top of the planetary boundary layer (PBL). Differential advection by wind shear created detached dust layers above the PBL that ascended due to radiative heating and arrived at the Phoenix site at heights corresponding to the LIDAR observations. The self-lifting of the dust layers is similar to the "solar escalator" mechanism for aerosol layers in the Earth's stratosphere.

High power RF window deposition apparatus, method, and device

DOEpatents

Ives, Lawrence R.; Lucovsky, Gerald; Zeller, Daniel

2017-07-04

A process for forming a coating for an RF window which has improved secondary electron emission and reduced multipactor for high power RF waveguides is formed from a substrate with low loss tangent and desirable mechanical characteristics. The substrate has an RPAO deposition layer applied which oxygenates the surface of the substrate to remove carbon impurities, thereafter has an RPAN deposition layer applied to nitrogen activate the surface of the substrate, after which a TiN deposition layer is applied using Titanium tert-butoxide. The TiN deposition layer is capped with a final RPAN deposition layer of nitridation to reduce the bound oxygen in the TiN deposition layer. The resulting RF window has greatly improved titanium layer adhesion, reduced multipactor, and is able to withstand greater RF power levels than provided by the prior art.

Interannual observations and quantification of summertime H2O ice deposition on the Martian CO2 ice south polar cap

USGS Publications Warehouse

Brown, Adrian J.; Piqueux, Sylvain; Titus, Timothy N.

2014-01-01

The spectral signature of water ice was observed on Martian south polar cap in 2004 by the Observatoire pour l'Mineralogie, l'Eau les Glaces et l'Activite (OMEGA) ( Bibring et al., 2004). Three years later, the OMEGA instrument was used to discover water ice deposited during southern summer on the polar cap ( Langevin et al., 2007). However, temporal and spatial variations of these water ice signatures have remained unexplored, and the origins of these water deposits remains an important scientific question. To investigate this question, we have used observations from the Compact Reconnaissance Imaging Spectrometer for Mars (CRISM) instrument on the Mars Reconnaissance Orbiter (MRO) spacecraft of the southern cap during austral summer over four Martian years to search for variations in the amount of water ice. We report below that for each year we have observed the cap, the magnitude of the H2O ice signature on the southern cap has risen steadily throughout summer, particularly on the west end of the cap. The spatial extent of deposition is in disagreement with the current best simulations of deposition of water ice on the south polar cap (Montmessin et al., 2007). This increase in water ice signatures is most likely caused by deposition of atmospheric H2O ice and a set of unusual conditions makes the quantification of this transport flux using CRISM close to ideal. We calculate a ‘minimum apparent‘ amount of deposition corresponding to a thin H2O ice layer of 0.2 mm (with 70% porosity). This amount of H2O ice deposition is 0.6–6% of the total Martian atmospheric water budget. We compare our ‘minimum apparent’ quantification with previous estimates. This deposition process may also have implications for the formation and stability of the southern CO2 ice cap, and therefore play a significant role in the climate budget of modern day Mars.

Confining the nucleation and overgrowth of Rh to the {111} facets of Pd nanocrystal seeds: the roles of capping agent and surface diffusion.

PubMed

Xie, Shuifen; Peng, Hsin-Chieh; Lu, Ning; Wang, Jinguo; Kim, Moon J; Xie, Zhaoxiong; Xia, Younan

2013-11-06

This article describes a systematic study of the spatially confined growth of Rh atoms on Pd nanocrystal seeds, with a focus on the blocking effect of a surface capping agent and the surface diffusion of adatoms. We initially used Pd cuboctahedrons as the seeds to illustrate the concept and to demonstrate the capabilities of our approach. Because the Pd{100} facets were selectively capped by a layer of chemisorbed Br(–) or I(–) ions, we were able to confine the nucleation and deposition of Rh atoms solely on the {111} facets of a Pd seed. When the synthesis was conducted at a relatively low temperature, the deposition of Rh atoms followed an island growth mode because of the high Rh–Rh interatomic binding energy. We also facilitated the surface diffusion of deposited Rh atoms by increasing the reaction temperature and decreasing the injection rate for the Rh precursor. Under these conditions, the deposition of Rh on the Pd{111} facets was switched to a layered growth mode. We further successfully extended this approach to a variety of other types of Pd polyhedral seeds that contained Pd{111} and Pd{100} facets in different proportions on the surface. As expected, a series of Pd–Rh bimetallic nanocrystals with distinctive elemental distributions were obtained. We could remove the Pd cores through selective chemical etching to generate Rh hollow nanoframes with different types and degrees of porosity. This study clearly demonstrates the importance of facet capping, surface diffusion, and reaction kinetics in controlling the morphologies of bimetallic nanocrystals during a seed-mediated process. It also provides a new direction for the rational design and synthesis of nanocrystals with spatially controlled distributions of elements for a variety of applications.

Use of life cycle assessments to evaluate the environmental footprint of contaminated sediment remediation.

PubMed

Sparrevik, Magnus; Saloranta, Tuomo; Cornelissen, Gerard; Eek, Espen; Fet, Annik Magerholm; Breedveld, Gijs D; Linkov, Igor

2011-05-15

Ecological and human risks often drive the selection of remedial alternatives for contaminated sediments. Traditional human and ecological risk assessment (HERA) includes assessing risk for benthic organisms and aquatic fauna associated with exposure to contaminated sediments before and after remediation as well as risk for human exposure but does not consider the environmental footprint associated with implementing remedial alternatives. Assessment of environmental effects over the whole life cycle (i.e., Life Cycle Assessment, LCA) could complement HERA and help in selecting the most appropriate sediment management alternative. Even though LCA has been developed and applied in multiple environmental management cases, applications to contaminated sediments and marine ecosystems are in general less frequent. This paper implements LCA methodology for the case of the polychlorinated dibenzo-p-dioxins and -furans (PCDD/F)-contaminated Grenland fjord in Norway. LCA was applied to investigate the environmental footprint of different active and passive thin-layer capping alternatives as compared to natural recovery. The results showed that capping was preferable to natural recovery when analysis is limited to effects related to the site contamination. Incorporation of impacts related to the use of resources and energy during the implementation of a thin layer cap increase the environmental footprint by over 1 order of magnitude, making capping inferior to the natural recovery alternative. Use of biomass-derived activated carbon, where carbon dioxide is sequestered during the production process, reduces the overall environmental impact to that of natural recovery. The results from this study show that LCA may be a valuable tool for assessing the environmental footprint of sediment remediation projects and for sustainable sediment management.