Multi-Sensor Based Online Attitude Estimation and Stability Measurement of Articulated Heavy Vehicles

PubMed Central

Xiao, Chunsheng; Liu, Yuanhui; Wu, Jinjin

2018-01-01

Articulated wheel loaders used in the construction industry are heavy vehicles and have poor stability and a high rate of accidents because of the unpredictable changes of their body posture, mass and centroid position in complex operation environments. This paper presents a novel distributed multi-sensor system for real-time attitude estimation and stability measurement of articulated wheel loaders to improve their safety and stability. Four attitude and heading reference systems (AHRS) are constructed using micro-electro-mechanical system (MEMS) sensors, and installed on the front body, rear body, rear axis and boom of an articulated wheel loader to detect its attitude. A complementary filtering algorithm is deployed for sensor data fusion in the system so that steady state margin angle (SSMA) can be measured in real time and used as the judge index of rollover stability. Experiments are conducted on a prototype wheel loader, and results show that the proposed multi-sensor system is able to detect potential unstable states of an articulated wheel loader in real-time and with high accuracy. PMID:29342850

Fuelcell-Hybrid Mine loader (LHD)

DOE Office of Scientific and Technical Information (OSTI.GOV)

James L Dippo; Tim Erikson; Kris Hess

2009-07-10

The fuel cell hybrid mine loader project, sponsored by a government-industry consortium, was implemented to determine the viability of proton exchange membrane (PEM) fuel cells in underground mining applications. The Department of Energy (DOE) sponsored this project with cost-share support from industry. The project had three main goals: (1) to develop a mine loader powered by a fuel cell, (2) to develop associated metal-hydride storage and refueling systems, and (3) to demonstrate the fuel cell hybrid loader in an underground mine in Nevada. The investigation of a zero-emissions fuel cell power plant, the safe storage of hydrogen, worker health advantagesmore » (over the negative health effects associated with exposure to diesel emissions), and lower operating costs are all key objectives for this project.« less

30 CFR 56.14101 - Brakes.

Code of Federal Regulations, 2014 CFR

2014-07-01

... particular piece of equipment. Front-end loaders shall be tested with the loader bucket empty. Equipment... speed the equipment is traveling except for equipment which is designed for the power train to be...

30 CFR 56.14101 - Brakes.

Code of Federal Regulations, 2011 CFR

2011-07-01

... particular piece of equipment. Front-end loaders shall be tested with the loader bucket empty. Equipment... speed the equipment is traveling except for equipment which is designed for the power train to be...

30 CFR 56.14101 - Brakes.

Code of Federal Regulations, 2013 CFR

2013-07-01

... particular piece of equipment. Front-end loaders shall be tested with the loader bucket empty. Equipment... speed the equipment is traveling except for equipment which is designed for the power train to be...

30 CFR 56.14101 - Brakes.

Code of Federal Regulations, 2012 CFR

2012-07-01

... particular piece of equipment. Front-end loaders shall be tested with the loader bucket empty. Equipment... speed the equipment is traveling except for equipment which is designed for the power train to be...

30 CFR 57.14101 - Brakes.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Front-end loaders shall be tested with the loader bucket empty. Equipment shall not be tested when... equipment which is designed for the power train to be disengaged during braking. (v) Testing speeds shall be...

30 CFR 57.14101 - Brakes.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Front-end loaders shall be tested with the loader bucket empty. Equipment shall not be tested when... equipment which is designed for the power train to be disengaged during braking. (v) Testing speeds shall be...

30 CFR 57.14101 - Brakes.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Front-end loaders shall be tested with the loader bucket empty. Equipment shall not be tested when... equipment which is designed for the power train to be disengaged during braking. (v) Testing speeds shall be...

30 CFR 57.14101 - Brakes.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Front-end loaders shall be tested with the loader bucket empty. Equipment shall not be tested when... equipment which is designed for the power train to be disengaged during braking. (v) Testing speeds shall be...

Mechanism of opening a sliding clamp

PubMed Central

Douma, Lauren G.; Yu, Kevin K.; England, Jennifer K.

2017-01-01

Abstract Clamp loaders load ring-shaped sliding clamps onto DNA where the clamps serve as processivity factors for DNA polymerases. In the first stage of clamp loading, clamp loaders bind and stabilize clamps in an open conformation, and in the second stage, clamp loaders place the open clamps around DNA so that the clamps encircle DNA. Here, the mechanism of the initial clamp opening stage is investigated. Mutations were introduced into the Escherichia coli β-sliding clamp that destabilize the dimer interface to determine whether the formation of an open clamp loader–clamp complex is dependent on spontaneous clamp opening events. In other work, we showed that mutation of a positively charged Arg residue at the β-dimer interface and high NaCl concentrations destabilize the clamp, but neither facilitates the formation of an open clamp loader–clamp complex in experiments presented here. Clamp opening reactions could be fit to a minimal three-step ‘bind-open-lock’ model in which the clamp loader binds a closed clamp, the clamp opens, and subsequent conformational rearrangements ‘lock’ the clamp loader–clamp complex in a stable open conformation. Our results support a model in which the E. coli clamp loader actively opens the β-sliding clamp. PMID:28973453

Automatic Test, Configuration, and Repair of Cellular Arrays

DTIC Science & Technology

1975-06-01

one cell to loed any good cell that is not walled off by flawed cells. The loading Information which the computer sends to the array may select one...to loed that cell’s loader and function-specificatioi state bits. After the cell is loaded» it« loader state bits may specify which of the cell’s...Mechanism With Options FUNCTION-SPEC, STATE BITS D.OUT INO INI OUTO 0UT1 LOO LO PAGE 99 LOADER TIP BITS CHANGER ill LSTA S.U.IN S.R.IN

9. PHOTOCOPY, ARCHITECTURAL SECTIONS AND DETAIL DRAWING OF UNDERGROUND STORAGE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. PHOTOCOPY, ARCHITECTURAL SECTIONS AND DETAIL DRAWING OF UNDERGROUND STORAGE MAGAZINES AND LAUNCHER-LOADER ASSEMBLIES. - NIKE Missile Base SL-40, Underground Storage Magazines & Launcher-Loader Assemblies, Southwesternmost end of launch area, Hecker, Monroe County, IL

An abstract class loader for the SSP and its implementation in TL.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wickstrom, Gregory Lloyd; Winter, Victor Lono; Fraij, Fares

2004-08-01

The SSP is a hardware implementation of a subset of the JVM for use in high consequence embedded applications. In this context, a majority of the activities belonging to class loading, as it is defined in the specification of the JVM, can be performed statically. Static class loading has the net result of dramatically simplifying the design of the SSP as well as increasing its performance. Due to the high consequence nature of its applications, strong evidence must be provided that all aspects of the SSP have been implemented correctly. This includes the class loader. This article explores the possibilitymore » of formally verifying a class loader for the SSP implemented in the strategic programming language TL. Specifically, an implementation of the core activities of an abstract class loader is presented and its verification in ACL2 is considered.« less

7. PHOTOCOPY, PLUMBING AND MECHANICAL PLAN AND DETAILS FOR UNDERGROUND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

7. PHOTOCOPY, PLUMBING AND MECHANICAL PLAN AND DETAILS FOR UNDERGROUND STORAGE MAGAZINES AND LAUNCHER-LOADER ASSEMBLIES. - NIKE Missile Base SL-40, Underground Storage Magazines & Launcher-Loader Assemblies, Southwesternmost end of launch area, Hecker, Monroe County, IL

8. PHOTOCOPY, ARCHITECTURAL FLOOR PLAN AND DETAIL DRAWING OF UNDERGROUND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

8. PHOTOCOPY, ARCHITECTURAL FLOOR PLAN AND DETAIL DRAWING OF UNDERGROUND STORAGE MAGAZINES AND LAUNCHER-LOADER ASSEMBLIES. - NIKE Missile Base SL-40, Underground Storage Magazines & Launcher-Loader Assemblies, Southwesternmost end of launch area, Hecker, Monroe County, IL

14 CFR 158.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... passenger by other parties. Ground support equipment means service and maintenance equipment used at an airport to support aeronautical operations and related activities. Baggage tugs, belt loaders, cargo loaders, forklifts, fuel trucks, lavatory trucks, and pushback tractors are among the types of vehicles...

146. FUEL LINE TO SKID 2 (FUEL LOADER) IN FUEL ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

146. FUEL LINE TO SKID 2 (FUEL LOADER) IN FUEL CONTROL ROOM (215), LSB (BLDG. 751). LIQUID NITROGEN/HELIUM HEAT EXCHANGER ON RIGHT. - Vandenberg Air Force Base, Space Launch Complex 3, Launch Pad 3 East, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

A Loader for Executing Multi-Binary Applications on the Thinking Machines CM-5: It's Not Just for SPMD Anymore

NASA Technical Reports Server (NTRS)

Becker, Jeffrey C.

1995-01-01

The Thinking Machines CM-5 platform was designed to run single program, multiple data (SPMD) applications, i.e., to run a single binary across all nodes of a partition, with each node possibly operating on different data. Certain classes of applications, such as multi-disciplinary computational fluid dynamics codes, are facilitated by the ability to have subsets of the partition nodes running different binaries. In order to extend the CM-5 system software to permit such applications, a multi-program loader was developed. This system is based on the dld loader which was originally developed for workstations. This paper provides a high level description of dld, and describes how it was ported to the CM-5 to provide support for multi-binary applications. Finally, it elaborates how the loader has been used to implement the CM-5 version of MPIRUN, a portable facility for running multi-disciplinary/multi-zonal MPI (Message-Passing Interface Standard) codes.

Whole-body vibration in heavy equipment operators of a front-end loader: role of task exposure and tire configuration with and without traction chains.

PubMed

Blood, Ryan P; Rynell, Patrik W; Johnson, Peter W

2012-12-01

This study measured whole-body vibration (WBV) exposures in front-end loader operators, and evaluated the effects of traction chains and work tasks on their WBV exposures. WBV exposures were measured and compared across three different front-end loader tire configurations: (a) stock rubber tires, (b) rubber tires with ladder chains, and (c) rubber tires with basket chains. The operators completed three distinct standardized tasks: driving on a city street, simulated plowing, and a simulated scooping and dumping task. A portable data acquisition system collected tri-axial time weighted and raw WBV data per ISO 2631-1 and 2631-5 standards. In addition, Global Positioning System (GPS) data were collected in order to compare loader speeds across tire conditions and the standardized tasks. Relative to the stock rubber tires, both types of tire chains significantly increased WBV exposures with the ladder chains having substantially higher WBV exposures compared to basket chains. Additionally, there were task dependent differences in WBV exposures. During the driving task, the z-axis (up and down) was the predominant exposure; the plowing task had a more even distribution of exposure across all three axes; while during scooping and dumping task, the x-axis (fore and aft) had the highest WBV exposures. The GPS data indicated that there were significant speed differences across tasks but not between the basket and ladder chain conditions. Tires with ladder chains increased the front-end loader operators' exposure to WBV above the ISO 2631-1 recommended eight hour action limit increasing risk for adverse health effects. Although more expensive, basket chains are recommended over ladder chains since they substantially lowered the front-end loader operator's exposures and may ultimately reduce vibration related wear and tear on the vehicle. In order to reduce a heavy equipment vehicle (HEV) operator's chances for developing low back pain, this study provides information that health and safety professionals can use to reduce whole-body vibration (WBV) exposures when operating front-end wheel loaders with traction chains. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

29 CFR 782.5 - Loaders.

Code of Federal Regulations, 2010 CFR

2010-07-01

... come within the exemption as a partial-duty loader. (Levinson v. Spector Motor Service, 330 U.S. 649... limited handling of them, that his activities will not come within the kind of “loading” which directly... it is light in weight, probably could not be loaded in a manner which would adversely affect “safety...

29 CFR 782.5 - Loaders.

Code of Federal Regulations, 2011 CFR

2011-07-01

... come within the exemption as a partial-duty loader. (Levinson v. Spector Motor Service, 330 U.S. 649... limited handling of them, that his activities will not come within the kind of “loading” which directly... it is light in weight, probably could not be loaded in a manner which would adversely affect “safety...

25. FRONT END LOADERS MOMENTARILY IN REPOSE IN THE ORE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. FRONT END LOADERS MOMENTARILY IN REPOSE IN THE ORE STORAGE YARD. AN ORE BRIDGE THAT FORMERLY TRANSFERRED ORE WITHIN THE STORAGE YARD WAS DESTROYED BY A BLIZZARD IN 1978. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

Safer methods of hauling coalface power loaders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Whitworth, K.

1976-01-01

That power loader chains are a menace is evidenced by the Report of H. M. Chief Inspector of Mines and Quarries in Great Britain. In 1974, power loader haulage chains were responsible for 40 percent of all machinery accidents, with one person killed and 18 seriously injured compared with 23 seriously injured in 1973. Half the accidents occurred in the vicinity of the power loader sprockets when persons were struck by the end of a broken chain or were trapped between the chain and the sprocket. The present static haulage chain in tension along the whole length of face ismore » a continuing hazard and the most significant safety contribution that can be made is to design alternative means of haulage to eliminate the chain. Alternative means of haulage have or are being developed and equipment from six machinery manufacturers, from CERCHAR, the French research and development organization, and from the British National Coal Board were demonstrated at the National Coal Board's Swadlincote Test Site. A brief description of each item of equipment is given.« less

Measurement of Spindle Rigidity by using a Magnet Loader

NASA Astrophysics Data System (ADS)

Yamazaki, Taku; Matsubara, Atsushi; Fujita, Tomoya; Muraki, Toshiyuki; Asano, Kohei; Kawashima, Kazuyuki

The static rigidity of a rotating spindle in the radial direction is investigated in this research. A magnetic loading device (magnet loader) has been developed for the measurement. The magnet loader, which has coils and iron cores, generates the electromagnetic force and attracts a dummy tool attached to the spindle. However, the eddy current is generated in the dummy tool with the spindle rotation and reduces the attractive force at high spindle speed. In order to understand the magnetic flux and eddy current in the dummy tool, the electromagnetic field analysis by FEM was carried out. Grooves on the attraction surface of the dummy tool were designed to cut the eddy current flow. The dimension of the groove were decided based on the FEM analysis, and the designed tool were manufactured and tested. The test result shows that the designed tool successfully reduces the eddy current and recovers the attractive force. By using the magnet loader and the grooved tool, the spindle rigidity can be measured when the spindle rotates with a speed up to 10,000 min-1.

Front End Loader Operator. Open Pit Mining Job Training Series.

ERIC Educational Resources Information Center

Savilow, Bill

This training outline for front end loader operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Comparison of mechanized systems for thinning Ponderosa pine and mixed conifer stands

Treesearch

Bruce R. Hartsough; Joseph F. McNeel; Thomas A. Durston; Bryce J. Stokes

1994-01-01

We studied three systems for thinning pine plantations and naturally-regenerated stands on the Stanislaus National Forest, California. All three produced small sawlogs and fuel chips. The whole tree system consisted of a feller buncher, skidder, stroke processor, loader and chipper. The cut-to-length system included a harvester, forwarder, loader and chipper. A hybrid...

Comparison of mechanized systems for thinning Ponderosa pine and mixed conifer stands

Treesearch

Bruce R. Hartsough; Joseph F. McNeel; Thomas A. Durston; Bryce J. Stokes

1994-01-01

Three systems for thinning pine plantations and naturally-regenerated stands were studied. All three produced small sawlogs and fuel chips. The whole-tree system consisted of a feller buncher, skidder, stroke processor, loader, and chipper. The cut-to-length system included a harvester, forwarder, loader, and chipper. A hybrid system combined a feller buncher,...

Association between photosynthesis and contrasting features of minor veins in leaves of summer annuals loading phloem via symplastic versus apoplastic routes.

PubMed

Muller, Onno; Cohu, Christopher M; Stewart, Jared J; Protheroe, Johanna A; Demmig-Adams, Barbara; Adams, William W

2014-09-01

Foliar vascular anatomy and photosynthesis were evaluated for a number of summer annual species that either load sugars into the phloem via a symplastic route (Cucumis sativus L. cv. Straight Eight; Cucurbita pepo L. cv. Italian Zucchini Romanesco; Citrullus lanatus L. cv. Faerie Hybrid; Cucurbita pepo L. cv. Autumn Gold) or an apoplastic route (Nicotiana tabacum L.; Solanum lycopersicum L. cv. Brandywine; Gossypium hirsutum L.; Helianthus annuus L. cv. Soraya), as well as winter annual apoplastic loaders (Spinacia oleracea L. cv. Giant Nobel; Arabidopsis thaliana (L.) Heynhold Col-0, Swedish and Italian ecotypes). For all summer annuals, minor vein cross-sectional xylem area and tracheid number as well as the ratio of phloem loading cells to phloem sieve elements, each when normalized for foliar vein density (VD), was correlated with photosynthesis. These links presumably reflect (1) the xylem's role in providing water to meet foliar transpirational demand supporting photosynthesis and (2) the importance of the driving force of phloem loading as well as the cross-sectional area for phloem sap flux to match foliar photosynthate production. While photosynthesis correlated with the product of VD and cross-sectional phloem cell area among symplastic loaders, photosynthesis correlated with the product of VD and phloem cell number per vein among summer annual apoplastic loaders. Phloem cell size has thus apparently been a target of selection among symplastic loaders (where loading depends on enzyme concentration within loading cells) versus phloem cell number among apoplastic loaders (where loading depends on membrane transporter numbers). © 2014 Scandinavian Plant Physiology Society.

Production and Costs of the Chambers Delimbinator in First Thinning of Pine Plantations

Treesearch

Scott T. Mooney; Kevin D. Boston; W. Dale Greene

2000-01-01

Production and quality measures were collected and analyzed for a new chain-flail delimbing machine, Chambers Delimbinator, on two operations in central and southwestern Georgia. The first operation, Logger A, used two skidders and one loader while the second operation, Logger B, used two skidder and two loaders. Lobber B with the lower cycle time and larger piece...

Pesticide Safety for Non-Certified Mixers, Loaders and Applicators = Uso Seguro de Pesticidas para Mezcladores, Cargadores y Aplicadores no Certificados.

ERIC Educational Resources Information Center

Poli, Bonnie; Fluker, Sam S.

Written in English and Spanish and completely illustrated, this manual provides basic safety information for pesticide workers. Mixers, loaders, and applicators work with pesticides at their greatest strength and have the highest risk of poisoning. Understanding the pesticide label is the first step to pesticide safety. The words…

Microbiologic contamination during dental radiographic film processing.

PubMed

Stanczyk, D A; Paunovich, E D; Broome, J C; Fatone, M A

1993-07-01

This study investigated microbiologic contamination of an automatic dental radiograph processor and daylight loader during a week of simulated clinical use. Pure cultures of Candida albicans, Streptococcus pneumoniae, Staphylococcus aureus, or Klebsiella pneumoniae were used to contaminate 320 vinyl intraoral radiograph packets. Each end of the films was deliberately contaminated during opening. These films and 24 uncontaminated control films were processed. Daylight loader ports, inlet and outlet rollers, fixer and developer samples, and 12 processed films were cultured daily. To simulate a weekend, the processor sites were cultured during 72 hours of inactivity after the contaminated runs. The results showed that contamination of the processor and daylight loader occurred and remained even after 48 hours of inactivity. Films remained contaminated after processing. In addition, cross-contamination of films occurred in the processor.

Cutter-loader apparatus having overhung shearer drum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Groger, H.; Harms, E.E.

1984-05-01

A longwall mining machine includes a drum cutter-loader and face conveyor wherein the drum cutter-loader is overhung and is supported by a support arm adjacent to the mine face. Nozzles direct high pressure liquid jets against the forward edge of the support arm to cut away the mining face and permit the face side support arm to advance as the mining machine advances. In one embodiment the nozzles are provided along an inclined cutting edge at the forward end of the support arm. Such nozzles may be fixed or oscillating. In an alternative embodiment the nozzles are provided in themore » cylindrical edge zone of the shearer drum and direct the high pressure fluid jets against the cutter edge at the forward end of the support arm.« less

TypeLoader: A fast and efficient automated workflow for the annotation and submission of novel full-length HLA alleles.

PubMed

Surendranath, V; Albrecht, V; Hayhurst, J D; Schöne, B; Robinson, J; Marsh, S G E; Schmidt, A H; Lange, V

2017-07-01

Recent years have seen a rapid increase in the discovery of novel allelic variants of the human leukocyte antigen (HLA) genes. Commonly, only the exons encoding the peptide binding domains of novel HLA alleles are submitted. As a result, the IPD-IMGT/HLA Database lacks sequence information outside those regions for the majority of known alleles. This has implications for the application of the new sequencing technologies, which deliver sequence data often covering the complete gene. As these technologies simplify the characterization of the complete gene regions, it is desirable for novel alleles to be submitted as full-length sequences to the database. However, the manual annotation of full-length alleles and the generation of specific formats required by the sequence repositories is prone to error and time consuming. We have developed TypeLoader to address both these facets. With only the full-length sequence as a starting point, Typeloader performs automatic sequence annotation and subsequently handles all steps involved in preparing the specific formats for submission with very little manual intervention. TypeLoader is routinely used at the DKMS Life Science Lab and has aided in the successful submission of more than 900 novel HLA alleles as full-length sequences to the European Nucleotide Archive repository and the IPD-IMGT/HLA Database with a 95% reduction in the time spent on annotation and submission when compared with handling these processes manually. TypeLoader is implemented as a web application and can be easily installed and used on a standalone Linux desktop system or within a Linux client/server architecture. TypeLoader is downloadable from http://www.github.com/DKMS-LSL/typeloader. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Mission-Based Analyses of Armor Training Requirements. Volume 7. Training Objectives for the XM1 Loader

DTIC Science & Technology

1982-04-01

the gas particulate filter system MODULE L: OPERATE THE M250 BRENADE LAUNCHER 1L. Load the grenade launcher 2L. Unload the grenade launcher MODULE M...k Initia~ng Stimulus: Thei (11rdLr from the T.C. to load the M250 .p grenade launcher. J ACTION Loader will: 1L. Load the grenade launcher. 2L. Unload

Handler, bystander and reentry exposure to TCDD from application of Agent Orange by C-123 aircraft during the Vietnam War.

PubMed

Ross, John H; Hewitt, Andrew; Armitage, James; Solomon, Keith; Watkins, Deborah K; Ginevan, Michael E

2015-02-01

Using validated models and methods routinely employed by pesticide regulatory agencies, the absorbed dosages of Agent Orange (AO) herbicide contaminant 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) were estimated for mixer/loaders, applicators, and individuals in the vicinity of applications of AO by C-123 aircraft during the Vietnam War. Resulting dosages of TCDD were then transformed to estimates of adipose residues, and compared to population biomonitoring of known mixer/loaders and applicators as well as ground troops in Vietnam and civilians in the U.S. Results demonstrate that mixer/loaders and applicators had the greatest exposures and their measured residues of TCDD in adipose were consistent with the estimated exposures. Further, the potentially exposed ground troops, including those who could have been directly sprayed during aerial defoliation, had measured adipose residues that were consistent with those in civilian U.S. populations with no defined source of exposure exposures and both of those cohorts had orders of magnitude less exposure than the mixer/loaders or applicators. Despite the availability of validated exposure modeling methods for decades, the quantitative TCDD dose estimates presented here are the first of their kind for the Vietnam conflict. Copyright © 2014 Elsevier B.V. All rights reserved.

The effects of a dynamic graphical model during simulation-based training of console operation skill

NASA Technical Reports Server (NTRS)

Farquhar, John D.; Regian, J. Wesley

1993-01-01

LOADER is a Windows-based simulation of a complex procedural task. The task requires subjects to execute long sequences of console-operation actions (e.g., button presses, switch actuations, dial rotations) to accomplish specific goals. The LOADER interface is a graphical computer-simulated console which controls railroad cars, tracks, and cranes in a fictitious railroad yard. We hypothesized that acquisition of LOADER performance skill would be supported by the representation of a dynamic graphical model linking console actions to goal and goal states in the 'railroad yard'. Twenty-nine subjects were randomly assigned to one of two treatments (i.e., dynamic model or no model). During training, both groups received identical text-based instruction in an instructional-window above the LOADER interface. One group, however, additionally saw a dynamic version of the bird's-eye view of the railroad yard. After training, both groups were tested under identical conditions. They were asked to perform the complete procedure without guidance and without access to either type of railroad yard representation. Results indicate that rather than becoming dependent on the animated rail yard model, subjects in the dynamic model condition apparently internalized the model, as evidenced by their performance after the model was removed.

GFU-6/E 30mm Ammunition Loader for GAU-8A Gun System

DTIC Science & Technology

1975-12-01

dropped onto the conveyor (See Figure 17) and transferred to the aircraft on these elements through flexible chuting which interfaces directly with the...14. Dwell Linkage 19 15. Horizontal Conveyor - Flex Chute Interface 20 16. Element Turnaround Sprocket 21 17. Horizontal Conveyor 22 18. Load Head... conveyor element mechanism for transport to the GAU-8/A loader unit. d. The contractor shall design the automated loading system to accept unfired

Modernization of Deployable Airfield Debris Removal Equipment

DTIC Science & Technology

2017-04-01

cleared the debris away from the crater by lowering the front bucket and setting the bottom blade at a 45-deg angle. The debris was pushed...the Komatsu WA 150 baseline loader. The crater clearing process involved the loader orienting the bucket blade at approximately 45 deg to the...wider than the track’s width (Figure 30). This caused debris to run under the track and lift the equipment, potentially throwing the operator. The final

The National Shipbuilding Research Program: Solid Waste Segregation and Recycling

DTIC Science & Technology

1998-03-01

Shields , Recycling Coordinator D.C. Department of Public Works 65 K Street, NE Washington, DC 20002 202-727-5887 Task Three, Tab Three Page 42 George...SHEAR X FRONT END LOADERS = CONVEYORS X FORKLIFTS O WEIGHT SCALES X PROCESSING DROP-BALL BREAKAGE X CUTTING TORCHES GAS = PLASMA = POWDER = WATER-JET...Loaders Conveyors Forklifts Weight Scales Processing Drop-ball Breakage Cutting Torches Gas Plasma Powder Laser Water-jet Abrasive disk Shears Ferrous

Improved memory loading techniques for the TSRV display system

NASA Technical Reports Server (NTRS)

Easley, W. C.; Lynn, W. A.; Mcluer, D. G.

1986-01-01

A recent upgrade of the TSRV research flight system at NASA Langley Research Center retained the original monochrome display system. However, the display memory loading equipment was replaced requiring design and development of new methods of performing this task. This paper describes the new techniques developed to load memory in the display system. An outdated paper tape method for loading the BOOTSTRAP control program was replaced by EPROM storage of the characters contained on the tape. Rather than move a tape past an optical reader, a counter was implemented which steps sequentially through EPROM addresses and presents the same data to the loader circuitry. A cumbersome cassette tape method for loading the applications software was replaced with a floppy disk method using a microprocessor terminal installed as part of the upgrade. The cassette memory image was transferred to disk and a specific software loader was written for the terminal which duplicates the function of the cassette loader.

Improvement of loading and transport bodies of tunneling machines

NASA Astrophysics Data System (ADS)

Nosenko, A. S.; Isakov, V. S.; Domnitskiy, A. A.; Shemshura, E. A.; Zubov, V. V.

2017-10-01

The article discusses the use of sets of equipment for mining and construction of road tunnels with the use of a self-propelled vehicle and bunker loaders to transport the mined rock. A patented design of the tunneling combine loading body, which allows adjusting its performance and power consumption in the loading mode, is considered. Reducing stress in extreme situations will make it possible to avoid overloading the drive and increase the reliability of the combine as a whole. The scheme of one of the most promising variants of the wedge bunker loader with variable geometry of the conveying elements is presented. The proposed design solves the problem of “locking” the material in narrow parts of the conveying body or in places where loading and transport bodies of different width are connected, as well as in the blast-and-heap mode of the loader.

Wrapping SRS with CORBA: from textual data to distributed objects.

PubMed

Coupaye, T

1999-04-01

Biological data come in very different shapes. Databanks are maintained and used by distinct organizations. Text is the de facto Standard exchange format. The SRS system can integrate heterogeneous textual databanks but it was lacking a way to structure the extracted data. This paper presents a CORBA interface to the SRS system which manages databanks in a flat file format. SRS Object Servers are CORBA wrappers for SRS. They allow client applications (visualisation tools, data mining tools, etc.) to access and query SRS servers remotely through an Object Request Broker (ORB). They provide loader objects that contain the information extracted from the databanks by SRS. Loader objects are not hard-coded but generated in a flexible way by using loader specifications which allow SRS administrators to package data coming from distinct databanks. The prototype may be available for beta-testing. Please contact the SRS group (http://srs.ebi.ac.uk).

Adult Competency Education Kit. Basic Skills in Speaking, Math, and Reading for Employment. Part R. ACE Competency Based Job Descriptions: #95--Bus Driver; #98--General Loader; #99--Forklift Operator; #100--Material Handler.

ERIC Educational Resources Information Center

San Mateo County Office of Education, Redwood City, CA. Career Preparation Centers.

This fifteenth of fifteen sets of Adult Competency Education (ACE) Competency Based Job Descriptions in the ACE kit contains job descriptions for Bus Driver, General Loader, Forklift Operator, and Material Handler. Each begins with a fact sheet that includes this information: occupational title, D.O.T. code, ACE number, career ladder, D.O.T.…

Elan4/SPARC V9 Cross Loader and Dynamic Linker

DOE Office of Scientific and Technical Information (OSTI.GOV)

anf Fabien Lebaillif-Delamare, Fabrizio Petrini

2004-10-25

The Elan4/Sparc V9 Croos Loader and Liner is a part of the Linux system software that allows the dynamic loading and linking of user code in the network interface Quadrics QsNETII, also called as Elan4 Quadrics. Elan44 uses a thread processor that is based on the assembly instruction set of the Sparc V9. All this software is integrated as a Linux kernel module in the Linux 2.6.5 release.

Evaluation of Wheel Loaders in Open Pit Marble Quarrying by Using the AHP and Topsis Approaches / Ocena pracy ładowarki na podwoziu kołowym w odkrywkowej kopalni marmuru w oparciu o metody AHP i topsis

NASA Astrophysics Data System (ADS)

Kun, Mete; Topaloǧlu, Şeyda; Malli, Tahir

2013-03-01

The marble mining in Turkey has been rising since the early 80's. In relation to that, the marble income has become noticeably bigger than those of other mining sectors. In recent years, marble and natural stone export composes half of the total mine export with a value of two billion dollars. This rapid development observed in marble operation has increased the importance of mining economics, income-expenditure balance and cost analysis. The most important cost elements observed in marble quarrying are machinery and equipment, labor costs and geological structures of the field. The aim of this study is to is to propose a multi-criteria decision making (MCDM) approach to evaluate the wheel loader alternatives and select the best loader under multiple criteria. A two-step methodology based on two MCDM methods, which are namely the Analytic Hierarchy Process (AHP) and the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS), are used in the evaluation procedure. More precisely, AHP is applied to determine the relative weights of evaluation criteria and TOPSIS is applied to rank the wheel loader alternatives. The proposed approach also provides a relatively simple and very well suited decision making tool for this type of decision making problems.

Logic Design of a Shared Disk System in a Multi-Micro Computer Environment.

DTIC Science & Technology

1983-06-01

overall system, is given. An exnaustive description of eacn device can De found in tne cited references. A. INTEL 80S5 Tne INTEL Be86 is a nign...eitner could De accomplished, it was necessary to understand ootn tne existing system arcnitecture ani software. Tne last cnapter addressed tnat...to De adapted: tne loader program and tne Doot ROP program. Tne loader program is a simplified version of CP/M-Bö and contains cniy encu^n file

Structural analysis of a eukaryotic sliding DNA clamp-clamp loadercomplex.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bowman, Gregory D.; O'Donnell, Mike; Kuriyan, John

2006-06-17

Sliding clamps are ring-shaped proteins that encircle DNA and confer high processivity on DNA polymerases. Here we report the crystal structure of the five-protein clamp loader complex (replication factor-C, RFC) of the yeast Saccharomyces cerevisiae, bound to the sliding clamp (proliferating cell nuclear antigen, PCNA). Tight interfacial coordination of the ATP analogue ATP-?-S by RFC results in a spiral arrangement of the ATPase domains of the clamp loader above the PCNA ring. Placement of a model for primed DNA within the central hole of PCNA reveals a striking correspondence between the RFC spiral and the grooves of the DNA doublemore » helix. This model, in which the clamp loader complex locks onto primed DNA in a screw-cap-like arrangement, provides a simple explanation for the process by which the engagement of primer-template junctions by the RFC:PCNA complex results in ATP hydrolysis and release of the sliding clamp on DNA.« less

Avoiding the Health Hazard of People from Construction Vehicles: A Strategy for Controlling the Vibration of a Wheel Loader

PubMed Central

Chi, Feng; Zhou, Jun; Zhang, Qi; Wang, Yong; Huang, Panling

2017-01-01

The vibration control of a construction vehicle must be carried out in order to meet the aims of sustainable environmental development and to avoid the potential human health hazards. In this paper, based on market feedback, the driver seat vibration of a type of wheel loader in the left and right direction, is found to be significant over a certain speed range. In order to find abnormal vibration components, the order tracking technique (OTT) and transmission path analysis (TPA) were used to analyze the vibration sources of the wheel loader. Through this analysis, it can be seen that the abnormal vibration comes from the interaction between the tire tread and the road, and this is because the vibration was amplified by the cab mount, which was eventually transmitted to the cab seat. Finally, the seat vibration amplitudes were decreased by up to 50.8%, after implementing the vibration reduction strategy. PMID:28282849

Avoiding the Health Hazard of People from Construction Vehicles: A Strategy for Controlling the Vibration of a Wheel Loader.

PubMed

Chi, Feng; Zhou, Jun; Zhang, Qi; Wang, Yong; Huang, Panling

2017-03-08

The vibration control of a construction vehicle must be carried out in order to meet the aims of sustainable environmental development and to avoid the potential human health hazards. In this paper, based on market feedback, the driver seat vibration of a type of wheel loader in the left and right direction, is found to be significant over a certain speed range. In order to find abnormal vibration components, the order tracking technique (OTT) and transmission path analysis (TPA) were used to analyze the vibration sources of the wheel loader. Through this analysis, it can be seen that the abnormal vibration comes from the interaction between the tire tread and the road, and this is because the vibration was amplified by the cab mount, which was eventually transmitted to the cab seat. Finally, the seat vibration amplitudes were decreased by up to 50.8%, after implementing the vibration reduction strategy.

Use of Semi-Autonomous Tools for ISS Commanding and Monitoring

NASA Technical Reports Server (NTRS)

Brzezinski, Amy S.

2014-01-01

As the International Space Station (ISS) has moved into a utilization phase, operations have shifted to become more ground-based with fewer mission control personnel monitoring and commanding multiple ISS systems. This shift to fewer people monitoring more systems has prompted use of semi-autonomous console tools in the ISS Mission Control Center (MCC) to help flight controllers command and monitor the ISS. These console tools perform routine operational procedures while keeping the human operator "in the loop" to monitor and intervene when off-nominal events arise. Two such tools, the Pre-positioned Load (PPL) Loader and Automatic Operators Recorder Manager (AutoORM), are used by the ISS Communications RF Onboard Networks Utilization Specialist (CRONUS) flight control position. CRONUS is responsible for simultaneously commanding and monitoring the ISS Command & Data Handling (C&DH) and Communications and Tracking (C&T) systems. PPL Loader is used to uplink small pieces of frequently changed software data tables, called PPLs, to ISS computers to support different ISS operations. In order to uplink a PPL, a data load command must be built that contains multiple user-input fields. Next, a multiple step commanding and verification procedure must be performed to enable an onboard computer for software uplink, uplink the PPL, verify the PPL has incorporated correctly, and disable the computer for software uplink. PPL Loader provides different levels of automation in both building and uplinking these commands. In its manual mode, PPL Loader automatically builds the PPL data load commands but allows the flight controller to verify and save the commands for future uplink. In its auto mode, PPL Loader automatically builds the PPL data load commands for flight controller verification, but automatically performs the PPL uplink procedure by sending commands and performing verification checks while notifying CRONUS of procedure step completion. If an off-nominal condition occurs during procedure execution, PPL Loader notifies CRONUS through popup messages, allowing CRONUS to examine the situation and choose an option of how PPL loader should proceed with the procedure. The use of PPL Loader to perform frequent, routine PPL uplinks offloads CRONUS to better monitor two ISS systems. It also reduces procedure performance time and decreases risk of command errors. AutoORM identifies ISS communication outage periods and builds commands to lock, playback, and unlock ISS Operations Recorder files. Operation Recorder files are circular buffer files of continually recorded ISS telemetry data. Sections of these files can be locked from further writing, be played back to capture telemetry data that occurred during an ISS loss of signal (LOS) period, and then be unlocked for future recording use. Downlinked Operation Recorder files are used by mission support teams for data analysis, especially if failures occur during LOS. The commands to lock, playback, and unlock Operations Recorder files are encompassed in three different operational procedures and contain multiple user-input fields. AutoORM provides different levels of automation for building and uplinking the commands to lock, playback, and unlock Operations Recorder files. In its automatic mode, AutoORM automatically detects ISS LOS periods, then generates and uplinks the commands to lock, playback, and unlock Operations Recorder files when MCC regains signal with ISS. AutoORM also features semi-autonomous and manual modes which integrate CRONUS more into the command verification and uplink process. AutoORMs ability to automatically detect ISS LOS periods and build the necessary commands to preserve, playback, and release recorded telemetry data greatly offloads CRONUS to perform more high-level cognitive tasks, such as mission planning and anomaly troubleshooting. Additionally, since Operations Recorder commands contain numerical time input fields which are tedious for a human to manually build, AutoORM's ability to automatically build commands reduces operational command errors. PPL Loader and AutoORM demonstrate principles of semi-autonomous operational tools that will benefit future space mission operations. Both tools employ different levels of automation to perform simple and routine procedures, thereby offloading human operators to perform higher-level cognitive tasks. Because both tools provide procedure execution status and highlight off-nominal indications, the flight controller is able to intervene during procedure execution if needed. Semi-autonomous tools and systems that can perform routine procedures, yet keep human operators informed of execution, will be essential in future long-duration missions where the onboard crew will be solely responsible for spacecraft monitoring and control.

Exposure to airborne organophosphates originating from hydraulic and turbine oils among aviation technicians and loaders.

PubMed

Solbu, Kasper; Daae, Hanne Line; Thorud, Syvert; Ellingsen, Dag Gunnar; Lundanes, Elsa; Molander, Paal

2010-12-01

This study describes the potential for occupational exposure to organophosphates (OPs) originating from turbine and hydraulic oils, among ground personnel within the aviation industry. The OPs tri-n-butyl phosphate (TnBP), dibutyl phenyl phosphate (DBPP), triphenyl phosphate (TPP) and tricresyl phosphate (TCP) have been emphasized due to their use in such oils. Oil aerosol/vapor and total volatile organic compounds (tVOCs) in air were also determined. In total, 228 and 182 OPs and oil aerosol/vapor samples from technician and loader work tasks during work on 42 and 21 aircrafts, respectively, were collected in pairs. In general, the measured exposure levels were below the limit of quantification (LOQ) for 84%/98% (oil aerosol) and 82%/90% (TCP) of the samples collected during technician/loader work tasks. The air concentration ranges for all samples related to technician work were

Remote drill bit loader

DOEpatents

Dokos, J.A.

1997-12-30

A drill bit loader is described for loading a tapered shank of a drill bit into a similarly tapered recess in the end of a drill spindle. The spindle has a transverse slot at the inner end of the recess. The end of the tapered shank of the drill bit has a transverse tang adapted to engage in the slot so that the drill bit will be rotated by the spindle. The loader is in the form of a cylinder adapted to receive the drill bit with the shank projecting out of the outer end of the cylinder. Retainer pins prevent rotation of the drill bit in the cylinder. The spindle is lowered to extend the shank of the drill bit into the recess in the spindle and the spindle is rotated to align the slot in the spindle with the tang on the shank. A spring unit in the cylinder is compressed by the drill bit during its entry into the recess of the spindle and resiliently drives the tang into the slot in the spindle when the tang and slot are aligned. 5 figs.

Remote drill bit loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dokos, James A.

A drill bit loader for loading a tapered shank of a drill bit into a similarly tapered recess in the end of a drill spindle. The spindle has a transverse slot at the inner end of the recess. The end of the tapered shank of the drill bit has a transverse tang adapted to engage in the slot so that the drill bit will be rotated by the spindle. The loader is in the form of a cylinder adapted to receive the drill bit with the shank projecting out of the outer end of the cylinder. Retainer pins prevent rotationmore » of the drill bit in the cylinder. The spindle is lowered to extend the shank of the drill bit into the recess in the spindle and the spindle is rotated to align the slot in the spindle with the tang on the shank. A spring unit in the cylinder is compressed by the drill bit during its entry into the recess of the spindle and resiliently drives the tang into the slot in the spindle when the tang and slot are aligned.« less

Remote drill bit loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dokos, J.A.

A drill bit loader is described for loading a tapered shank of a drill bit into a similarly tapered recess in the end of a drill spindle. The spindle has a transverse slot at the inner end of the recess. The end of the tapered shank of the drill bit has a transverse tang adapted to engage in the slot so that the drill bit will be rotated by the spindle. The loader is in the form of a cylinder adapted to receive the drill bit with the shank projecting out of the outer end of the cylinder. Retainer pinsmore » prevent rotation of the drill bit in the cylinder. The spindle is lowered to extend the shank of the drill bit into the recess in the spindle and the spindle is rotated to align the slot in the spindle with the tang on the shank. A spring unit in the cylinder is compressed by the drill bit during its entry into the recess of the spindle and resiliently drives the tang into the slot in the spindle when the tang and slot are aligned. 5 figs.« less

Prototyping Faithful Execution in a Java virtual machine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tarman, Thomas David; Campbell, Philip LaRoche; Pierson, Lyndon George

2003-09-01

This report presents the implementation of a stateless scheme for Faithful Execution, the design for which is presented in a companion report, ''Principles of Faithful Execution in the Implementation of Trusted Objects'' (SAND 2003-2328). We added a simple cryptographic capability to an already simplified class loader and its associated Java Virtual Machine (JVM) to provide a byte-level implementation of Faithful Execution. The extended class loader and JVM we refer to collectively as the Sandia Faithfully Executing Java architecture (or JavaFE for short). This prototype is intended to enable exploration of more sophisticated techniques which we intend to implement in hardware.

An analysis of injuries to front-end loader operators during ingress and egress.

PubMed

Nasarwanji, Mahiyar F; Pollard, Jonisha; Porter, William

2018-05-01

Slips, trips, and falls from mobile mining equipment have been documented for decades. However, little research has been conducted to determine the events precipitating these incidents during ingress or egress. This study examined slips, trips, and falls sustained during ingress or egress from front-end loaders to determine the frequencies of factors that may contribute to injuries. Non-fatal injuries, when getting on or off of front-end wheel loaders specifically, were identified, coded, and analyzed from the Mine Safety and Health Administration's accidents, injuries, and illnesses database. Overall trends, events that precipitated the injury, injuries sustained, contributing factors, location of the individual, and equipment characteristics were analyzed. More incidents occurred during egress (63%); and egress is believed to be more hazardous than ingress. Foot slips were the most common event that precipitated the incident and the leading cause of these was contaminants on the equipment. Misstep, loss of footing, and step on/in related incidents were more common during egress and are likely due to the operator's reduced visibility when descending a ladder facing the equipment, limiting their ability to detect hazards. Egress also makes an operator less capable of avoiding unsafe ground conditions as indicated by the significant number of step on/in injuries occurring on the ground during egress. Most of the front-end loaders associated with the incidents were found to have bottom rungs with flexible rails, which may also increase fall risk during egress due to inconsistent rung heights and lengthy transition areas from the ground, through the flexible-railed rungs, to the rungs with rigid rails. Recommendations are provided to reduce the risk for slips, trips, and falls from mobile mining equipment.

Modelling and study of active vibration control for off-road vehicle

NASA Astrophysics Data System (ADS)

Zhang, Junwei; Chen, Sizhong

2014-05-01

In view of special working characteristics and structure, engineering machineries do not have conventional suspension system typically. Consequently, operators have to endure severe vibrations which are detrimental both to their health and to the productivity of the loader. Based on displacement control, a kind of active damping method is developed for a skid-steer loader. In this paper, the whole hydraulic system for active damping method is modelled which include swash plate dynamics model, proportional valve model, piston accumulator model, pilot-operated check valve model, relief valve model, pump loss model, and cylinder model. A new road excitation model is developed for the skid-steer loader specially. The response of chassis vibration acceleration to road excitation is verified through simulation. The simulation result of passive accumulator damping is compared with measurements and the comparison shows that they are close. Based on this, parallel PID controller and track PID controller with acceleration feedback are brought into the simulation model, and the simulation results are compared with passive accumulator damping. It shows that the active damping methods with PID controllers are better in reducing chassis vibration acceleration and pitch movement. In the end, the test work for active damping method is proposed for the future work.

Inactivation of the budding yeast cohesin loader Scc2 alters gene expression both globally and in response to a single DNA double strand break

PubMed Central

Lindgren, Emma; Hägg, Sara; Giordano, Fosco; Björkegren, Johan; Ström, Lena

2014-01-01

Genome integrity is fundamental for cell survival and cell cycle progression. Important mechanisms for keeping the genome intact are proper sister chromatid segregation, correct gene regulation and efficient repair of damaged DNA. Cohesin and its DNA loader, the Scc2/4 complex have been implicated in all these cellular actions. The gene regulation role has been described in several organisms. In yeast it has been suggested that the proteins in the cohesin network would effect transcription based on its role as insulator. More recently, data are emerging indicating direct roles for gene regulation also in yeast. Here we extend these studies by investigating whether the cohesin loader Scc2 is involved in regulation of gene expression. We performed global gene expression profiling in the absence and presence of DNA damage, in wild type and Scc2 deficient G2/M arrested cells, when it is known that Scc2 is important for DNA double strand break repair and formation of damage induced cohesion. We found that not only the DNA damage specific transcriptional response is distorted after inactivation of Scc2 but also the overall transcription profile. Interestingly, these alterations did not correlate with changes in cohesin binding. PMID:25483075

Application of Quality Management Tools for Evaluating the Failure Frequency of Cutter-Loader and Plough Mining Systems

NASA Astrophysics Data System (ADS)

Biały, Witold

2017-06-01

Failure frequency in the mining process, with a focus on the mining machine, has been presented and illustrated by the example of two coal-mines. Two mining systems have been subjected to analysis: a cutter-loader and a plough system. In order to reduce costs generated by failures, maintenance teams should regularly make sure that the machines are used and operated in a rational and effective way. Such activities will allow downtimes to be reduced, and, in consequence, will increase the effectiveness of a mining plant. The evaluation of mining machines' failure frequency contained in this study has been based on one of the traditional quality management tools - the Pareto chart.

US Army Armor Reference Data in Three Volumes. Volume II. Nondivisional Organizations.

DTIC Science & Technology

1981-01-01

SQuat 1r) R 2 SGI IB20 (Team Ldr) R I SP4 19GIO (Loader/Gnr) P I SP5 19G20 (St Gunner) P 1 t,5 19G20 (Sr Gunner) P I SP4 IICII ()Carrrr Dv) P 2 SP4 11810...Sergeant 2 SP4 Mat Storage Sp 1 SIC Platoon SOT1 SPC Food Svc SGT 1 SP4 Supply Con & Acct Cik 1 SP4 Lt Veh DriverI SFC Motor Sergeant I SP4 Subsistence...PLATOON Ho-.-- Loader Scoop Type 2-1/2 CU YD .Platoon Leader Tank Fabric Fuel 10,000-Gal. 1 SPC Platoon SC? 1 PFlC Reports Clerk 0lRadio Set N/VRC-46

Insights into the structure and assembly of the Bacillus subtilis clamp-loader complex and its interaction with the replicative helicase

PubMed Central

Afonso, José P.; Chintakayala, Kiran; Suwannachart, Chatrudee; Sedelnikova, Svetlana; Giles, Kevin; Hoyes, John B.; Soultanas, Panos; Rafferty, John B.; Oldham, Neil J.

2013-01-01

The clamp-loader complex plays a crucial role in DNA replication by loading the β-clamp onto primed DNA to be used by the replicative polymerase. Relatively little is known about the stoichiometry, structure and assembly pathway of this complex, and how it interacts with the replicative helicase, in Gram-positive organisms. Analysis of full and partial complexes by mass spectrometry revealed that a hetero-pentameric τ3-δ-δ′ Bacillus subtilis clamp-loader assembles via multiple pathways, which differ from those exhibited by the Gram-negative model Escherichia coli. Based on this information, a homology model of the B. subtilis τ3-δ-δ′ complex was constructed, which revealed the spatial positioning of the full C-terminal τ domain. The structure of the δ subunit was determined by X-ray crystallography and shown to differ from that of E. coli in the nature of the amino acids comprising the τ and δ′ binding regions. Most notably, the τ-δ interaction appears to be hydrophilic in nature compared with the hydrophobic interaction in E. coli. Finally, the interaction between τ3 and the replicative helicase DnaB was driven by ATP/Mg2+ conformational changes in DnaB, and evidence is provided that hydrolysis of one ATP molecule by the DnaB hexamer is sufficient to stabilize its interaction with τ3. PMID:23525462

30 CFR 77.1109 - Quantity and location of firefighting equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... construction. (c)(1) Mobile equipment, including trucks, front-end loaders, bulldozers, portable welding units...) Fire extinguishers shall be provided at permanent electrical installations commensurate with the...

Osmotic mechanism of the loop extrusion process

NASA Astrophysics Data System (ADS)

Yamamoto, Tetsuya; Schiessel, Helmut

2017-09-01

The loop extrusion theory assumes that protein factors, such as cohesin rings, act as molecular motors that extrude chromatin loops. However, recent single molecule experiments have shown that cohesin does not show motor activity. To predict the physical mechanism involved in loop extrusion, we here theoretically analyze the dynamics of cohesin rings on a loop, where a cohesin loader is in the middle and unloaders at the ends. Cohesin monomers bind to the loader rather frequently and cohesin dimers bind to this site only occasionally. Our theory predicts that a cohesin dimer extrudes loops by the osmotic pressure of cohesin monomers on the chromatin fiber between the two connected rings. With this mechanism, the frequency of the interactions between chromatin segments depends on the loading and unloading rates of dimers at the corresponding sites.

Design and evaluation of a slave manipulator with roll-pitch-roll wrist and automatic tool loading mechanism in telerobotic surgery.

PubMed

Kim, Ki-Young; Lee, Jung-Ju

2012-12-01

As there is a shortage of scrub nurses in many hospitals, automatic surgical tool exchanging mechanism without human labour has been studied. Minimally invasive robotic surgeries (MIRS) also require scrub nurses. A surgical tool loading mechanism without a scrub nurse's assistance for MIRS is proposed. Many researchers have developed minimally invasive surgical instruments with a wrist joint that can be movable inside the abdomen. However, implementation of a distal rolling joint on a gripper is rare. To implement surgical tool exchanging without a scrub nurse's assistance, a slave manipulator and a tool loader were developed to load and unload a surgical tool unit. A surgical tool unit with a roll-pitch-roll wrist was developed. Several experiments were performed to validate the effectiveness of the slave manipulator and the surgical tool unit. The slave manipulator and the tool loader were able to successfully unload and load the surgical tool unit without human assistance. The total duration of unloading and loading the surgical tool unit was 97 s. Motion tracking experiments of the distal rolling joint were performed. The maximum positioning error of the step input response was 2°. The advantage of the proposed slave manipulator and tool loader is that other robotic systems or human labour are not needed for surgical tool loading. The feasibility of the distal rolling joint in MIS is verified. Copyright © 2012 John Wiley & Sons, Ltd.

1. MAGAZINE COMPLEX, O, P, AND Q. MAGAZINE P IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. MAGAZINE COMPLEX, O, P, AND Q. MAGAZINE P IN BACKGROUND, LOOKING NORTHEAST. - NIKE Missile Base C-84, Underground Storage Magazines & Launcher-Loader Assemblies, Easternmost portion of launch area, Barrington, Cook County, IL

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Steel Products (available at each Regional Office of the Occupational Safety and Health... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Steel Products (available at each Regional Office of the Occupational Safety and Health... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Code of Federal Regulations, 2010 CFR

2010-07-01

... of Steel Products (available at each Regional Office of the Occupational Safety and Health... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Steel Products (available at each Regional Office of the Occupational Safety and Health... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

Code of Federal Regulations, 2012 CFR

2012-07-01

... of Steel Products (available at each Regional Office of the Occupational Safety and Health... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

Cognitive simulation of incident risks in the structure of loading and transport enterprise

NASA Astrophysics Data System (ADS)

Shishkina, S. V.; Pristupa, Yu D.; Pavlova, L. D.; Fryanov, V. N.

2017-09-01

Organizational and technical system of a manufacturing enterprise was identified, which includes three subsystems: main production, industrial and social infrastructure. Based on the results of cognitive modeling, significant system concepts were identified that reduce the risks of incidents. The internal control influences formed in accordance with level of competence of heads of services, departments, sections, dispatchers, acting on the basis of regulations, job profiles. The second concept influencing the enterprise management system is personnel, which is assessed by the compliance of competencies of crane operators, loader operators, slingers, loaders, and acceptance/delivery agents to job responsibilities and labor functions. At a low level of professional competencies, the personnel does not fully comply with job duties and labor functions, the risk of an incident is maximal. The application of cognitive modeling allows us to identify the essential elements that ensure stable functioning of the system as a whole.

In-line drivetrain and four wheel drive work machine using same

DOEpatents

Hoff, Brian

2008-08-05

A four wheel drive articulated mine loader is powered by a fuel cell and propelled by a single electric motor. The drivetrain has the first axle, second axle, and motor arranged in series on the work machine chassis. Torque is carried from the electric motor to the back differential via a pinion meshed with the ring gear of the back differential. A second pinion oriented in an opposite direction away from the ring gear is coupled to a drive shaft to transfer torque from the ring gear to the differential of the front axle. Thus, the ring gear of the back differential acts both to receive torque from the motor and to transfer torque to the forward axle. The in-line drive configuration includes a single electric motor and a single reduction gear to power the four wheel drive mine loader.

Remote drill bit loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dokos, J.A.

1996-12-31

A drill bit loader is described for loading a tapered shank of a drill bit into a similarly tapered recess in the end of a drill spindle. The spindle has a transverse slot at the inner end of the recess. The end of the tapered shank of the drill bit has a transverse tang adapted to engage in the slot so that the drill bit will be rotated by the spindle. The loader is in the form of a cylinder adapted to receive the drill bit with the shank projecting out of the outer end of the cylinder. Retainer pinsmore » prevent rotation of the drill bit in the cylinder. The spindle is lowered to extend the shank of the drill bit into the recess in the spindle and the spindle is rotated to align the slot in the spindle with the tang on the shank. A spring unit in the cylinder is compressed by the drill bit during its entry into the recess of the spindle and resiliently drives the tang into the slot in the spindle when the tang and slot are aligned. In typical remote drilling operations, whether in hot cells or water pits, drill bits have been held using a collet or end mill type holder with set screws. In either case, to load or change a drill bit required the use master-slave manipulators to position the bits and tighten the collet or set screws. This requirement eliminated many otherwise useful work areas because they were not equipped with slaves, particularly in water pits.« less

Extension modules for storage, visualization and querying of genomic, genetic and breeding data in Tripal databases

PubMed Central

Lee, Taein; Cheng, Chun-Huai; Ficklin, Stephen; Yu, Jing; Humann, Jodi; Main, Dorrie

2017-01-01

Abstract Tripal is an open-source database platform primarily used for development of genomic, genetic and breeding databases. We report here on the release of the Chado Loader, Chado Data Display and Chado Search modules to extend the functionality of the core Tripal modules. These new extension modules provide additional tools for (1) data loading, (2) customized visualization and (3) advanced search functions for supported data types such as organism, marker, QTL/Mendelian Trait Loci, germplasm, map, project, phenotype, genotype and their respective metadata. The Chado Loader module provides data collection templates in Excel with defined metadata and data loaders with front end forms. The Chado Data Display module contains tools to visualize each data type and the metadata which can be used as is or customized as desired. The Chado Search module provides search and download functionality for the supported data types. Also included are the tools to visualize map and species summary. The use of materialized views in the Chado Search module enables better performance as well as flexibility of data modeling in Chado, allowing existing Tripal databases with different metadata types to utilize the module. These Tripal Extension modules are implemented in the Genome Database for Rosaceae (rosaceae.org), CottonGen (cottongen.org), Citrus Genome Database (citrusgenomedb.org), Genome Database for Vaccinium (vaccinium.org) and the Cool Season Food Legume Database (coolseasonfoodlegume.org). Database URL: https://www.citrusgenomedb.org/, https://www.coolseasonfoodlegume.org/, https://www.cottongen.org/, https://www.rosaceae.org/, https://www.vaccinium.org/

Assessment of respirable dust and its free silica contents in different Indian coalmines.

PubMed

Mukherjee, Ashit K; Bhattacharya, Sanat K; Saiyed, Habibullah N

2005-04-01

Assessment of respirable dust, personal exposures of miners and free silica contents in dust were undertaken to find out the associated risk of coal workers' pneumoconiosis in 9 coal mines of Eastern India during 1988-91. Mine Research Establishment (MRE), 113A Gravimetric Dust Sampler (GDS) and personal samplers (AFC 123), Cassella, London, approved by Director General of Mines Safety (DGMS) were used respectively for monitoring of mine air dust and personal exposures of miners. Fourier Transform Infra-red (FTIR) Spectroscopy determined free silica in respirable dusts. Thermal Conditions like Wet Bulb Globe Temperature (WBGT) index, humidity and wind velocity were also recorded during monitoring. The dust levels in the face return air of both, Board & Pillar (B&P) and Long Wall (LW) mining were found above the permissible level recommended by DGMS, Govt. of India. The drilling, blasting and loading are the major dusty operations in B&P method. Exposures of driller and loader were varied between, 0.81-9.48 mg/m3 and 0.05-9.84 mg/m3 respectively in B&P mining, whereas exposures of DOSCO loader, Shearer operator and Power Support Face Worker were varied between 2.65-9.11 mg/m3, 0.22-10.00 mg/m3 and 0.12-9.32 mg/m3 respectively in LW mining. In open cast mining, compressor and driller operators are the major exposed groups. The percentage silica in respirable dusts found below 5% in all most all the workers except among query loaders and drillers of open cast mines.

--No Title--

Science.gov Websites

;background:url(/technical-assistance/assets/images/ajax-loader.gif) center center no-repeat}.btn-long{font-size :0 0 10px}.btn-long{height:80px}}@media only screen and (min-width :1200px){.btn-long{height:60px

PRN 2009-1: Establishment of Antimicrobial Exposure Assessment Task Force II

EPA Pesticide Factsheets

This PR notice announces the establishment of the Antimicrobial Exposure Assessment Task Force II, an industry-wide task force to develop mixer, loader, applicator and post-application exposure data for antimicrobial pesticides used in various settings.

14 CFR 158.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Definitions. 158.3 Section 158.3 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS... airport to support aeronautical operations and related activities. Baggage tugs, belt loaders, cargo...

14 CFR 158.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Definitions. 158.3 Section 158.3 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRPORTS... airport to support aeronautical operations and related activities. Baggage tugs, belt loaders, cargo...

PRN 2007-3: The Agricultural Handlers Exposure Task Force, L.L.C

EPA Pesticide Factsheets

This PR Notice discusses the Agricultural Handlers Exposure Task Force, an industry-wide task force formed to develop mixer, loader, and applicator exposure data for pesticides used in agricultural settings. It includes contacts for more information.

Numerical assessment of fore-and-aft suspension performance to reduce whole-body vibration of wheel loader drivers

NASA Astrophysics Data System (ADS)

Fleury, Gérard; Mistrot, Pierre

2006-12-01

While driving off-road vehicles, operators are exposed to whole-body vibration acting in the fore-and-aft direction. Seat manufacturers supply products equipped with fore-and-aft suspension but only a few studies report on their performance. This work proposes a computational approach to design fore-and-aft suspensions for wheel loader seats. Field tests were conducted in a quarry to analyse the nature of vibration to which the driver was exposed. Typical input signals were recorded to be reproduced in the laboratory. Technical specifications are defined for the suspension. In order to evaluate the suspension vibration attenuation performance, a model of a sitting human body was developed and coupled to a seat model. The seat model combines the models of each suspension component. A linear two-degree-of-freedom model is used to describe the dynamic behaviour of the sitting driver. Model parameters are identified by fitting the computed apparent mass frequency response functions to the measured values. Model extensions are proposed to investigate postural effects involving variations in hands and feet positions and interaction of the driver's back with the backrest. Suspension design parameters are firstly optimized by computing the seat/man model response to sinusoidal acceleration. Four criteria including transmissibility, interaction force between the driver's back and the backrest and relative maximal displacement of the suspension are computed. A new suspension design with optimized features is proposed. Its performance is checked from calculations of the response of the seat/man model subjected to acceleration measured on the wheel loader during real work conditions. On the basis of the computed values of the SEAT factors, it is found possible to design a suspension that would increase the attenuation provided by the seat by a factor of two.

Is increased joint loading detrimental to obese patients with knee osteoarthritis? A secondary data analysis from a randomized trial.

PubMed

Henriksen, M; Hunter, D J; Dam, E B; Messier, S P; Andriacchi, T P; Lohmander, L S; Aaboe, J; Boesen, M; Gudbergsen, H; Bliddal, H; Christensen, R

2013-12-01

To investigate whether increased knee joint loading due to improved ambulatory function and walking speed following weight loss achieved over 16 weeks accelerates symptomatic and structural disease progression over a subsequent 1 year weight maintenance period in an obese population with knee osteoarthritis (OA). Data from a prospective study of weight loss in obese patients with knee OA (the CARtilage in obese knee OsteoarThritis (CAROT) study) were used to determine changes in knee joint compressive loadings (model estimated) during walking after a successful 16 week weight loss intervention. The participants were divided into 'Unloaders' (participants that reduced joint loads) and 'Loaders' (participants that increased joint loads). The primary symptomatic outcome was changes in knee symptoms, measured with the Knee injury and Osteoarthritis Outcome Score (KOOS) questionnaire, during a subsequent 52 weeks weight maintenance period. The primary structural outcome was changes in tibiofemoral cartilage loss assessed semi-quantitatively (Boston Leeds Knee Osteoarthritis Score (BLOKS) from MRI after the 52 weight maintenance period. 157 participants (82% of the CAROT cohort) with medial and/or lateral knee OA were classified as Unloaders (n = 100) or Loaders (n = 57). The groups showed similar significant changes in symptoms (group difference: -2.4 KOOS points [95% CI -6.8:1.9]) and cartilage loss (group difference: -0.06 BLOKS points [95% CI -0.22:0.11) after 1 year, with no statistically significant differences between Loaders and Unloaders. For obese patients undergoing a significant weight loss, increased knee joint loading for 1 year was not associated with accelerated symptomatic and structural disease progression compared to a similar weight loss group that had reduced ambulatory compressive knee joint loads. NCT00655941. Copyright © 2013 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Real world duty cycles and utilization for construction equipment in North Carolina.

DOT National Transportation Integrated Search

2008-01-04

Field data for in-use fuel consumption and emission rates were collected for 15 nonroad vehicles using a portable emission : measurement system (PEMS). Each vehicle, including 5 backhoes, 4 front end loaders, and 6 motor graders, were tested : once o...

Comparison of simulator fidelity model predictions with in-simulator evaluation data

NASA Technical Reports Server (NTRS)

Parrish, R. V.; Mckissick, B. T.; Ashworth, B. R.

1983-01-01

A full factorial in simulator experiment of a single axis, multiloop, compensatory pitch tracking task is described. The experiment was conducted to provide data to validate extensions to an analytic, closed loop model of a real time digital simulation facility. The results of the experiment encompassing various simulation fidelity factors, such as visual delay, digital integration algorithms, computer iteration rates, control loading bandwidths and proprioceptive cues, and g-seat kinesthetic cues, are compared with predictions obtained from the analytic model incorporating an optimal control model of the human pilot. The in-simulator results demonstrate more sensitivity to the g-seat and to the control loader conditions than were predicted by the model. However, the model predictions are generally upheld, although the predicted magnitudes of the states and of the error terms are sometimes off considerably. Of particular concern is the large sensitivity difference for one control loader condition, as well as the model/in-simulator mismatch in the magnitude of the plant states when the other states match.

Volvo CE to expand driveline components and introduce new loader concept at bauma

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2007-04-15

This suppliers news report includes a description of Volvo CE's Graphic wheel loader which uses an electric hybrid power sources and is almost emissions free. Simulator training technology is proving its usefulness in establishing higher safety levels in the mining industry. Immersive Technologies Advanced Equipment training simulators are being used to train students at the Academy for Mine Training and Energy Technology in West Virginia. Geo-Explorer core drills manufactured by Multi-Power Products Ltd. of Canada have been purchased by the Pan African Mining Corp. One is to be assigned to the company's coal program where an extensive exploration program ismore » underway in the Sakoa area in Madagascar. A joint venture agreement has been announced between iPackets International and China's Henan YongAn Investment Guarantee Co. and China Coal Information Institute. Under the name GuoAn Mine Safety Communication System, iPacket's wireless communications software and equipment will be deployed in China's mining industry. 3 photos.« less

Assessment of whole-body vibration exposures and influencing factors for quarry haul truck drivers and loader operators

PubMed Central

Mayton, Alan G.; Jobes, Christopher C.; Gallagher, Sean

2015-01-01

To further assess vibration exposure on haul trucks (HTs) and front-end wheel loaders (FELs), follow-up investigations were conducted at two US crushed stone operations. The purpose was to: 1) evaluate factors such as load/no-load conditions, speed, load capacity, vehicle age, and seat transmissibility relative to vibration exposure; 2) compare exposure levels with existing ISO/ANSI and EUGPG guidelines. Increasing HT speed increased recorded vibration at the chassis and seat as expected. Neither vehicle load nor vehicle speed increased transmissibility. Increasing HT size and age did show transmissibility decreasing. HT dominant-axis wRMS levels (most often the y-axis, lateral or side-to-side direction) were predominantly within the health guidance caution zone (HGCZ). However, several instances showed vibration dose value (VDV) above the exposure limit value (ELV) for the ISO/ANSI guidelines. VDV levels (all dominant x-axis or fore-aft) were within and above the HGCZ for the EUGPG and above the HGCZ for ISO/ANSI guidelines. PMID:26361493

Design and performance tests of a distributed power-driven wheel loader

NASA Astrophysics Data System (ADS)

Jin, Xiaolin; Shi, Laide; Bian, Yongming

2010-03-01

An improved ZLM15B distributed power-driven wheel loader was designed, whose travel and brake system was accomplished by two permanent magnet synchronous motorized-wheels instead of traditional mechanical components, and whose hydraulic systems such as the working device system and steering system were both actuated by an induction motor. All above systems were flexibly coupled with 3-phase 380VAC electric power with which the diesel engine power is replaced. On the level cement road, traveling, braking, traction and steering tests were carried out separately under non-load and heavy-load conditions. Data show that machine speed is 5 km/h around and travel efficiency of motorized-wheels is above 95%; that machine braking deceleration is between 0.5 and 0.64 m/s2 but efficiency of motorized-wheels is less than 10%; that maximum machine traction is above 2t while efficiency of motorized-wheels is more than 90% and that adaptive differential steering can be smoothly achieved by motorized-wheels.

Design and performance tests of a distributed power-driven wheel loader

NASA Astrophysics Data System (ADS)

Jin, Xiaolin; Shi, Laide; Bian, Yongming

2009-12-01

An improved ZLM15B distributed power-driven wheel loader was designed, whose travel and brake system was accomplished by two permanent magnet synchronous motorized-wheels instead of traditional mechanical components, and whose hydraulic systems such as the working device system and steering system were both actuated by an induction motor. All above systems were flexibly coupled with 3-phase 380VAC electric power with which the diesel engine power is replaced. On the level cement road, traveling, braking, traction and steering tests were carried out separately under non-load and heavy-load conditions. Data show that machine speed is 5 km/h around and travel efficiency of motorized-wheels is above 95%; that machine braking deceleration is between 0.5 and 0.64 m/s2 but efficiency of motorized-wheels is less than 10%; that maximum machine traction is above 2t while efficiency of motorized-wheels is more than 90% and that adaptive differential steering can be smoothly achieved by motorized-wheels.

The 1990-1991 project summaries

NASA Technical Reports Server (NTRS)

1991-01-01

Project summaries for 1990-91 at the Georgia Institute of Technology are presented. The following research projects were studied: a lunar surface vehicle model; lunar loader/transporter; trenching and cable-laying device for the lunar surface; a lunar vehicle system for habitat transport and placement; and lunar storage facility.

Non-accident release of hazmat from railroad tank cars : training issues

DOT National Transportation Integrated Search

1999-07-01

This report presents the results of a study to determine the extent to which written materials used in training railroad tank car HAZMAT loaders are consistent with the reading skills of the trainees. Data from four case study sites was used to condu...

30 CFR 56.14106 - Falling object protection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Falling object protection. 56.14106 Section 56... Equipment Safety Devices and Maintenance Requirements § 56.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 57.14106 - Falling object protection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Falling object protection. 57.14106 Section 57... Equipment Safety Devices and Maintenance Requirements § 57.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 56.14106 - Falling object protection.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Falling object protection. 56.14106 Section 56... Equipment Safety Devices and Maintenance Requirements § 56.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 57.14106 - Falling object protection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Falling object protection. 57.14106 Section 57... Equipment Safety Devices and Maintenance Requirements § 57.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 56.14106 - Falling object protection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Falling object protection. 56.14106 Section 56... Equipment Safety Devices and Maintenance Requirements § 56.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 57.14106 - Falling object protection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Falling object protection. 57.14106 Section 57... Equipment Safety Devices and Maintenance Requirements § 57.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 57.14106 - Falling object protection.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Falling object protection. 57.14106 Section 57... Equipment Safety Devices and Maintenance Requirements § 57.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 57.14106 - Falling object protection.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Falling object protection. 57.14106 Section 57... Equipment Safety Devices and Maintenance Requirements § 57.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 56.14106 - Falling object protection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Falling object protection. 56.14106 Section 56... Equipment Safety Devices and Maintenance Requirements § 56.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

30 CFR 56.14106 - Falling object protection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Falling object protection. 56.14106 Section 56... Equipment Safety Devices and Maintenance Requirements § 56.14106 Falling object protection. (a) Fork-lift trucks, front-end loaders, and bulldozers shall be provided with falling object protective structures if...

Radiological tele-immersion for next generation networks.

PubMed

Ai, Z; Dech, F; Rasmussen, M; Silverstein, J C

2000-01-01

Since the acquisition of high-resolution three-dimensional patient images has become widespread, medical volumetric datasets (CT or MR) larger than 100 MB and encompassing more than 250 slices are common. It is important to make this patient-specific data quickly available and usable to many specialists at different geographical sites. Web-based systems have been developed to provide volume or surface rendering of medical data over networks with low fidelity, but these cannot adequately handle stereoscopic visualization or huge datasets. State-of-the-art virtual reality techniques and high speed networks have made it possible to create an environment for clinicians geographically distributed to immersively share these massive datasets in real-time. An object-oriented method for instantaneously importing medical volumetric data into Tele-Immersive environments has been developed at the Virtual Reality in Medicine Laboratory (VRMedLab) at the University of Illinois at Chicago (UIC). This networked-VR setup is based on LIMBO, an application framework or template that provides the basic capabilities of Tele-Immersion. We have developed a modular general purpose Tele-Immersion program that automatically combines 3D medical data with the methods for handling the data. For this purpose a DICOM loader for IRIS Performer has been developed. The loader was designed for SGI machines as a shared object, which is executed at LIMBO's runtime. The loader loads not only the selected DICOM dataset, but also methods for rendering, handling, and interacting with the data, bringing networked, real-time, stereoscopic interaction with radiological data to reality. Collaborative, interactive methods currently implemented in the loader include cutting planes and windowing. The Tele-Immersive environment has been tested on the UIC campus over an ATM network. We tested the environment with 3 nodes; one ImmersaDesk at the VRMedLab, one CAVE at the Electronic Visualization Laboratory (EVL) on east campus, and a CT scan machine in UIC Hospital. CT data was pulled directly from the scan machine to the Tele-Immersion server in our Laboratory, and then the data was synchronously distributed by our Onyx2 Rack server to all the VR setups. Instead of permitting medical volume visualization at one VR device, by combining teleconferencing, tele-presence, and virtual reality, the Tele-Immersive environment will enable geographically distributed clinicians to intuitively interact with the same medical volumetric models, point, gesture, converse, and see each other. This environment will bring together clinicians at different geographic locations to participate in Tele-Immersive consultation and collaboration.

30 CFR 46.5 - New miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

... the recognition and avoidance of electrical hazards and other hazards present at the mine, such as traffic patterns and control, mobile equipment (e.g., haul trucks and front-end loaders), and loose or... aspects of an assigned task in paragraph (b)(4) of this section, if hazard recognition training specific...

30 CFR 46.5 - New miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the recognition and avoidance of electrical hazards and other hazards present at the mine, such as traffic patterns and control, mobile equipment (e.g., haul trucks and front-end loaders), and loose or... aspects of an assigned task in paragraph (b)(4) of this section, if hazard recognition training specific...

Hydrographic Service Royal Australian Navy

DTIC Science & Technology

1993-01-01

relocation of the Hydrographic Office to Wollongong, NSW; "* A marked decline in chart production caused by workforce changes as a result of the impending...amalgamate the plans of Clinton Coal Loader Wharf and Auckland Point to Barney Point in one plan at scale 1:10 000. The chart now provides continuous

Index to Benet Weapons Laboratory (LCWSL) Technical Reports - 1979

DTIC Science & Technology

1980-09-01

Breech Machanisms Breech Seals Breeches, Cannon Cadmium Sulfide Calibration Cannon Auto Loader Cannon Tube Chemical Vapor Deposition REPORT NUMBER...PAGE(Trh«n Data SntaracQ (Con1t from block #20) Three basic specimen geometries were studied: 1. A symetric specimen; 2. A specimen with +5% wall

Federal Workplace Literacy Project. Internal Evaluation Report.

ERIC Educational Resources Information Center

Matuszak, David J.

This report describes the following components of the Nestle Workplace Literacy Project: six job task analyses, curricula for six workplace basic skills training programs, delivery of courses using these curricula, and evaluation of the process. These six job categories were targeted for training: forklift loader/checker, BB's processing systems…

Standard Electronic Format Specification for Tank Characterization Data Loader Version 3.5

DOE Office of Scientific and Technical Information (OSTI.GOV)

ADAMS, M.R.

2001-01-31

The purpose of this document is to describe the standard electronic format for data files that will be sent for entry into the Tank Characterization Database (TCD). There are 2 different file types needed for each data load: (1) Analytical Results and (2) Sample Descriptions.

Low-Capital Systems for Thinning Pine Plantations

Treesearch

John Wilhoit; Qingyue Ling; Robert Rummer

1999-01-01

Highly mechanized systems utilizing rubber-tired skidders, feller-bunchers, and knuckleboom loaders are the predominant type of timber harvesting operation in the southern United States. These systems, which handle the wood in tree-length form, are highly productive and very efficient, especially for large tracts of timber. Thinnings constitute an increasing proportion...

29 CFR 1926.1400 - Scope.

Code of Federal Regulations, 2011 CFR

2011-07-01

... loaders. This machinery is also excluded when used with chains, slings or other rigging to lift suspended... that deliver material to a construction site when the crane is used to transfer building supply sheet goods or building supply packaged materials from the truck crane onto a structure, using a fork/cradle...

77 FR 38087 - Agency Information Collection Activities; Submission for OMB Review; Comment Request...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-26

... protective equipment to protect miners from harmful levels of noise that can result in hearing loss. However..., relies on drills, crushers, compressors, conveyors, trucks, loaders, and other heavy-duty equipment for the excavation, haulage, and processing of material. This equipment creates high sound levels...

77 FR 16865 - Proposed Extension of Existing Information Collection; Occupational Noise Exposure

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-22

..., administrative controls, and personal protective equipment to protect miners from harmful levels of noise that..., compressors, conveyors, trucks, loaders, and other heavy-duty equipment for the excavation, haulage, and processing of material. This equipment creates high sound levels, exposing machine operators as well as...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or, American...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or, American...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or, American...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2013 CFR

2013-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or American...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2012 CFR

2012-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or American...

30 CFR Appendix I to Subpart M of... - National Consensus Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... loaders and bulldozers Society of Automotive Engineers (SAE) minimum performance criteria for falling object protective structures (FOPS) SAE J231—January, 1981. Fork-lift trucks American National Standards Institute (ANSI) safety standard for low lift and high lift trucks, B 56.1, section 7.27—1983; or American...

30 CFR 46.6 - Newly hired experienced miner training.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Instruction on the recognition and avoidance of electrical hazards and other hazards present at the mine, such as traffic patterns and control, mobile equipment (e.g., haul trucks and front-end loaders), and... health and safety aspects of an assigned task in paragraph (b)(4) of this section, if hazard recognition...

30 CFR 46.6 - Newly hired experienced miner training.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Instruction on the recognition and avoidance of electrical hazards and other hazards present at the mine, such as traffic patterns and control, mobile equipment (e.g., haul trucks and front-end loaders), and... health and safety aspects of an assigned task in paragraph (b)(4) of this section, if hazard recognition...

76 FR 36548 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-22

...] Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and... of Committee: Circulatory System Devices Panel of the Medical Devices Advisory Committee. General... also comes with a sheath, introducer, loader, dilator, balloon (used to pre-dilate the native annulus...

77 FR 25183 - Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-27

...] Circulatory System Devices Panel of the Medical Devices Advisory Committee; Notice of Meeting AGENCY: Food and... of Committee: Circulatory System Devices Panel of the Medical Devices Advisory Committee. General..., introducer, loader, dilator, balloon (used to pre-dilate the native annulus) and a crimper. FDA intends to...

40 CFR Table 9 to Subpart Wwww of... - Initial Compliance With Work Practice Standards

Code of Federal Regulations, 2014 CFR

2014-07-01

... compression/injection molding uncover, unwrap or expose only one charge per mold cycle per compression/injection molding machine. For machines with multiple molds, one charge means sufficient material to fill... cycle per compression/injection molding machine, or prior to the loader, hoppers are closed except when...

--No Title--

Science.gov Websites

background-color: #e5e5e5; } h3 { line-height: 20px; padding-bottom: 10px; } #appheader { margin ; position: relative; text-align: center; font-size: 16pt; /*font-weight: bold;*/ /*color: rgb(165,180,212 );*/ color: rgb(62, 96, 163); background: url('../images/ajax-loader.gif') 50% 50% no-repeat; } .container

The Impact of Wireless Technology on Loading Trucks at an Auto Parts Distribution Center

ERIC Educational Resources Information Center

Goomas, David T.

2012-01-01

An intervention was introduced for truck loaders that used wireless vehicle mount computers that included auditory, visual feedback, and immediate data delivery. The implementation reliably reduced pallets from being loaded out of sequence for all outbound trucks in multistop routes. The role of the organizational behavior management (OBM)…

Justification of process of loading coal onto face conveyors by auger heads of shearer-loader machines

NASA Astrophysics Data System (ADS)

Nguyen, K. L.; Gabov, V. V.; Zadkov, D. A.; Le, T. B.

2018-03-01

This paper analyzes the processes of removing coal from the area of its dislodging and loading the disintegrated mass onto face conveyors by auger heads of shearer-loader machines. The loading process is assumed to consist of four subprocesses: dislodging coal, removal of the disintegrated mass by auger blades from the crushing area, passive transportation of the disintegrated mass, and forming the load flow on the bearing surface of a face conveyor. Each of the considered subprocesses is different in its physical nature, the number of factors influencing it, and can be complex or multifactor. Possibilities of improving the efficiency of loading coal onto a face conveyor are addressed. The selected criteria of loading efficiency are load rate, specific energy consumption, and coal size reduction. Efficiency is improved by reducing the resistance to movement of the disintegrated mass during loading by increasing the area of the loading window section and the volume of the loading area on the conveyor, as well as by coordination of intensity of flows related to the considered processes in local areas.

Gamma-ray exposure hazard due to stowage of M-774 APFSDS (Armour-piercing fin-stabilized discarding-sabot) rounds in a Leopard C-1 main battle tank. Technical note

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robitaille, H.A.

1983-09-01

The M-744 APFSDS anti-tank round contains a depleted-uranium penetrator of 3.4 kgram mass. Since depleted uranium is naturally radioactive, the storage of a substantial number of these rounds inside a Leopard C-1 main battle tank creates a gamma radiation field within the vehicle. Gamma-ray exposure rates have been measured using a sodium-iodide spectrometer at each of the four crew-member locations and for two turret orientations, with 59 rounds stowed in the vehicle. In all cases the measured gamma-ray dose rates were less than a maximum of 0.17 millirad per hour observed at the loader's position. Assuming the loader spent anmore » entire week (168 hours) at his station, his integrated dose would amount to 29 mRad - approximately a factor of 4 lower than the maximum currently allowed by Canadian Forces regulations. It is therefore concluded that the M774 round does not represent a significant gamma radiation hazard to Leopard C1 crewmembers.« less

M60 Tank Personnel Heater Comparison Test, Fort Carson, Colorado

DTIC Science & Technology

1983-05-01

A study should be made considering the logisites and cost implications of developing a kit to upgrade the Model "C" heater to include self ...l f L Summary of Questionnaire Respose -for BLU (Model "A" with Engine Filter/Heat Tape) System Driver Loader Gunner TC’* " # % # % * % # 9 12. Heat

29 CFR 782.8 - Special classes of carriers.

Code of Federal Regulations, 2013 CFR

2013-07-01

..., and ice) to railroad, docks, etc., for use of trains and steamships is not such transportation as is... cases cited in § 782.7(c), and see Mitchell v. Independent Ice Co., 294 F. 2d 186 (C.A. 5), certiorari..., driver's helpers, loaders, and mechanics employed by companies engaged in such activities are covered by...

29 CFR 782.8 - Special classes of carriers.

Code of Federal Regulations, 2014 CFR

2014-07-01

..., and ice) to railroad, docks, etc., for use of trains and steamships is not such transportation as is... cases cited in § 782.7(c), and see Mitchell v. Independent Ice Co., 294 F. 2d 186 (C.A. 5), certiorari..., driver's helpers, loaders, and mechanics employed by companies engaged in such activities are covered by...

29 CFR 782.8 - Special classes of carriers.

Code of Federal Regulations, 2012 CFR

2012-07-01

..., and ice) to railroad, docks, etc., for use of trains and steamships is not such transportation as is... cases cited in § 782.7(c), and see Mitchell v. Independent Ice Co., 294 F. 2d 186 (C.A. 5), certiorari..., driver's helpers, loaders, and mechanics employed by companies engaged in such activities are covered by...

Chapter 5: Loosening compacted soils on mined lands

Treesearch

B. Strahm; R. Sweigard; J. Burger; D. Graves; C. Zipper; C. Barton; J. Skousen; P. Angel

2017-01-01

Successful surface coal mining businesses must move earth materials efficiently, so mining operations today depend on large and heavy equipment (Fig. 5-1). Track dozers and haul trucks used for mining can weigh more than 100 tons each. Wheel loaders and loaded haul trucks often exceed 200 tons. The mining industry has learned that successful reforestation of reclaimed...

ARC-2008-ACD08-0217-001

NASA Image and Video Library

2008-09-24

Aeronautics Technical Seminar series: Pilot Force Measurement with Inertia and Gravity Compensation by Rodger A. Mueller (offering an interesting behind-the-scenes look at some of the research that goes into creating high-fedelity, pilot-control loader simulation experiences for pilots and astronauts using the world renowned NASA Ames Vertical Motion Simulator) Series audio on file in Ames Library

ARC-2008-ACD08-0217-002

NASA Image and Video Library

2008-09-24

Aeroanutics Technical Seminar series: Pilot Force Measurement with Inertia and Gravity Compensation by Rodger A. Mueller (offering an interesting behind-the-scenes look at some of the research that goes into creating high-fedelity, pilot-control loader simulation experiences for pilots and astronauts using the world renowned NASA Ames Vertical Motion Simulator) Series audio on file in Ames Library

ARC-2008-ACD08-0217-003

NASA Image and Video Library

2008-09-24

Aeroanutics Technical Seminar series: Pilot Force Measurement with Inertia and Gravity Compensation by Rodger A. Mueller (offering an interesting behind-the-scenes look at some of the research that goes into creating high-fedelity, pilot-control loader simulation experiences for pilots and astronauts using the world renowned NASA Ames Vertical Motion Simulator) Series audio on file in Ames Library

76 FR 37795 - Notice of Availability of Government-Owned Inventions; Available for Licensing

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-28

... DEPARTMENT OF DEFENSE Department of the Navy Notice of Availability of Government-Owned Inventions....S. Patent No. 7,316,194: Rudders for High-Speed Ships//U.S. Patent No. 7,322,786: Mobile Loader for Transfer of Containers Between Delivery Vehicles and Marine Terminal Cranes//U.S. Patent No. 7,324,016...

Department of Defense In-House RDT&E Activities

DTIC Science & Technology

1981-10-30

DISEASES*.’......*......... 43 MISSILE LABORATORY ................................................. 44 MOBILITY EQUIPMENT R&D COMMAND...HELICOPTER INFLIGHT MONITORING SYS WITH INSTRUMENTED RANGE; ANECHOIC AND REVERBERATION CHAMBERS; MOBILE -’ ACCOUSTICS LAB; EYE MOVEMENT MEASURING...IN- CLUDES: LIGHTWEIGIHT OPTICAL TRACKING SYSTEM, 25-TON CRANE, 2 20-TON MOBILE CRANES, 5-TON WRECKER, 40,000 LB ACFT LOADER, THREE T-28B ACFT, 1 UH

77 FR 14495 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Final Results of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-12

... counterbalanced lift truck is a rigid framed, engine- powered machine with lift arms that has additional weight...; \\7\\ (2) construction vehicles and equipment, including earthmover articulated dump products, rigid frame haul trucks,\\8\\ front end loaders,\\9\\ dozers,\\10\\ lift trucks, straddle carriers,\\11\\ graders,\\12...

76 FR 62356 - Certain New Pneumatic Off-the-Road Tires From the People's Republic of China: Preliminary Results...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

...-steer loaders are four-wheel drive vehicles with the left-side drive wheels independent of the right... exporter can demonstrate that it is sufficiently independent so as to be entitled to a separate rate.\\28... separate rate analysis is not necessary to determine whether it is independent from government control.\\29...

Environmental Assessment: Anti-Terrorism/Force Protection McConnell Air Force Base, Kansas

DTIC Science & Technology

2003-09-01

handled, stored, transported, disposed, or recycled in accordance with these regulations. The potential for hazardous waste generation from gate...Loader (rubber tire) Concrete Truck Concrete Finisher Crane Asphalt Spreader Roller Flat Bed Truck (18 wheel) Scraper Trenching Machine 1...plastics, and lumber. These materials would be placed in the appropriate construction materials landfill or recycled when possible. These wastes

The Weak Link HP-41C hand-held calculator program

Treesearch

Ross A. Phillips; Penn A. Peters; Gary D. Falk

1982-01-01

The Weak Link hand-held calculator program (HP-41C) quickly analyzes a system for logging production and costs. The production equations model conventional chain saw, skidder, loader, and tandemaxle truck operations in eastern mountain areas. Production of each function of the logging system may be determined so that the system may be balanced for minimum cost. The...

Comparison of two thinning systems. Part 1. Stand and site impacts

Treesearch

Bobby L. Lanford; Bryce J. Stokes

1995-01-01

During the winter of 1991, a side-by-side comparison was made between two popular thinning systems:a feller-buncher, grapple skidder, loader/slasher system and a harvester, forwarder system. A first commercial thinning was conducted in an 18-year-old loblolly pine stand Test areas were cruised prior to thinning and remeasured after operations were completed The target...

Development and testing of a computer assisted remote-control system for the compact loader-trammer. Report of Investigations/1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruff, T.M.

1992-01-01

A prototype mucking machine designed to operate in narrow vein stopes was developed by Foster-Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader/trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether remote control system, a computer-based, radio remote control was retrofitted to the minimucker. Initialmore » tests indicated a need to assist the operator in guiding the machine in narrow stopes and an automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote control system are reviewed, and an ultrasonic, sensor-based guidance system is described.« less

Development of the Los Alamos National Laboratory Cryogenic Pressure Loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ebey, Peter S.; Dole, James M.; Hoffer, James K.

2003-05-15

Targets for inertial fusion research and ignition at OMEGA, the National Ignition Facility, LMJ, and future facilities rely on beta-radiation-driven layering of spherical cryogenic DT ice layers contained within plastic or metal shells. Plastic shells will be permeation filled at room temperature then cooled to cryogenic temperatures before removal of the overpressure. The cryogenic pressure loader (CPL) was recently developed at Los Alamos National Laboratory as a testbed for studying the filling and layering of plastic target shells with DT. A technical description of the CPL is provided. The CPL consists of a cryostat, which contains a high-pressure permeation cell,more » and has optical access for investigating beta layering. The cryostat is housed within a tritium glovebox that contains manifolds for supplying high-pressure DT. The CPL shares some design elements with the cryogenic target handling system at the OMEGA facility to allow testing of tritium issues related to that system. The CPL has the capability to fill plastic targets by permeation to pressures up to 100 MPa and to cool them to 15 K. The CPL will accommodate a range of targets and may be modified for future experiments.« less

Cryo-EM structure of a helicase loading intermediate containing ORC–Cdc6–Cdt1–MCM2-7 bound to DNA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Jingchuan; Evrin, Cecile; Samel, Stefan A.

2013-07-14

In eukaryotes, the Cdt1-bound replicative helicase core MCM2-7 is loaded onto DNA by the ORC–Cdc6 ATPase to form a prereplicative complex (pre-RC) with an MCM2-7 double hexamer encircling DNA. Using purified components in the presence of ATP-γS, we have captured in vitro an intermediate in pre-RC assembly that contains a complex between the ORC–Cdc6 and Cdt1–MCM2-7 heteroheptamers called the OCCM. Cryo-EM studies of this 14-subunit complex reveal that the two separate heptameric complexes are engaged extensively, with the ORC–Cdc6 N-terminal AAA+ domains latching onto the C-terminal AAA+ motor domains of the MCM2-7 hexamer. The conformation of ORC–Cdc6 undergoes a concertedmore » change into a right-handed spiral with helical symmetry that is identical to that of the DNA double helix. The resulting ORC–Cdc6 helicase loader shows a notable structural similarity to the replication factor C clamp loader, suggesting a conserved mechanism of action.« less

A practical tool for monitoring the performance of measuring systems in a laboratory network: report of an ACB Working Group.

PubMed

Ayling, Pete; Hill, Robert; Jassam, Nuthar; Kallner, Anders; Khatami, Zahra

2017-11-01

Background A logical consequence of the introduction of robotics and high-capacity analysers has seen a consolidation to larger units. This requires new structures and quality systems to ensure that laboratories deliver consistent and comparable results. Methods A spreadsheet program was designed to accommodate results from up to 12 different instruments/laboratories and present IQC data, i.e. Levey-Jennings and Youden plots and comprehensive numerical tables of the performance of each item. Input of data was made possible by a 'data loader' by which IQC data from the individual instruments could be transferred to the spreadsheet program on line. Results A set of real data from laboratories is used to populate the data loader and the networking software program. Examples are present from the analysis of variance components, the Levey-Jennings and Youden plots. Conclusions This report presents a software package that allows the simultaneous management and detailed monitoring of the performance of up to 12 different instruments/laboratories in a fully interactive mode. The system allows a quality manager of networked laboratories to have a continuous updated overview of the performance. This software package has been made available at the ACB website.

Protection of the vehicle cab environment against bacteria, fungi and endotoxins in composting facilities.

PubMed

Schlosser, O; Huyard, A; Rybacki, D; Do Quang, Z

2012-06-01

Microbial quality of air inside vehicle cabs is a major occupational health risk management issue in composting facilities. Large differences and discrepancies in protection factors between vehicles and between biological agents have been reported. This study aimed at estimating the mean protection efficiency of the vehicle cab environment against bioaerosols with higher precision. In-cab measurement results were also analysed to ascertain whether or not these protection systems reduce workers' exposure to tolerable levels. Five front-end loaders, one mobile mixer and two agricultural tractors pulling windrow turners were investigated. Four vehicles were fitted with a pressurisation and high efficiency particulate air (HEPA) filtration system. The four others were only equipped with pleated paper filter without pressurisation. Bacteria, fungi and endotoxins were measured in 72 pairs of air samples, simultaneously collected inside the cab and on the outside of the cab with a CIP 10-M sampler. A front-end loader, purchased a few weeks previously, fitted with a pressurisation and high efficiency particulate air (HEPA) filtration system, and with a clean cab, exhibited a mean protection efficiency of between 99.47% CI 95% [98.58-99.97%] and 99.91% [99.78-99.98%] depending on the biological agent. It is likely that the lower protection efficiency demonstrated in other vehicles was caused by penetration through the only moderately efficient filters, by the absence of pressurisation, by leakage in the filter-sealing system, and by re-suspension of particles which accumulated in dirty cabs. Mean protection efficiency in regards to bacteria and endotoxins ranged between 92.64% [81.87-97.89%] and 98.61% [97.41-99.38%], and between 92.68% [88.11-96.08%] and 98.43% [97.44-99.22%], respectively. The mean protection efficiency was the lowest when confronted with fungal spores, from 59.76% [4.19-90.75%] to 94.71% [91.07-97.37%]. The probability that in-cab exposure to fungi exceeded the benchmark value for short-term respiratory effects suggests that front-end loaders and mobile mixers in composting facilities should be fitted with a pressurisation and HEPA filtration system, regardless of whether or not the facility is indoors or outdoors. Regarding the tractors, exposure inside the cabs was not significantly reduced. However, in this study, there was a less than 0.01% risk of exceeding the bench mark value associated with fungi related short-term respiratory effects during an 1-h per day windrow turning operation. Pressurisation and a HEPA filtration system can provide safe working conditions inside loaders and mobile mixer with regard to airborne bacteria, fungi and endotoxins in composting facilities. However, regular thorough cleaning of the vehicle cab, as well as overalls and shoes cleaning, and mitigation of leakage in the filter-sealing system are necessary to achieve high levels of protection efficiency. Copyright © 2012 Elsevier Ltd. All rights reserved.

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

24. BUILDING NO. 452, ORDNANCE FACILITY (BAG CHARGE FILLING PLANT), INTERIOR VIEW LOOKING WEST AT NORTH END OF CENTRAL CORRIDOR (ROOM 3). STAIRWAY WORKBENCH WITH COMPRESSED-AIR POWERED CARTRIDGE LOADER. ARMORED PASS-THROUGH OF TRANSFER BOX FOR PASSING EXPLOSIVES MATERIALS THROUGH TO NEXT ROOM TO THE NORTH. - Picatinny Arsenal, 400 Area, Gun Bag Loading District, State Route 15 near I-80, Dover, Morris County, NJ

Conveyor-Loader Plastic Toy Parts (toys and games) 9-13.01--Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

29 CFR 782.5 - Loaders.

Code of Federal Regulations, 2012 CFR

2012-07-01

... parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133, 134, 139), is an employee of a carrier subject to section... U.S. 649; Pyramid Motor Freight Corp. v. Ispass, 330 U.S. 695; Walling v. Gordon's Transport (W.D...; Walling v. Huber & Huber Motor Express, 67 F. Supp. 855; Ex parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133...

29 CFR 782.5 - Loaders.

Code of Federal Regulations, 2013 CFR

2013-07-01

... parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133, 134, 139), is an employee of a carrier subject to section... U.S. 649; Pyramid Motor Freight Corp. v. Ispass, 330 U.S. 695; Walling v. Gordon's Transport (W.D...; Walling v. Huber & Huber Motor Express, 67 F. Supp. 855; Ex parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133...

29 CFR 782.5 - Loaders.

Code of Federal Regulations, 2014 CFR

2014-07-01

... parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133, 134, 139), is an employee of a carrier subject to section... U.S. 649; Pyramid Motor Freight Corp. v. Ispass, 330 U.S. 695; Walling v. Gordon's Transport (W.D...; Walling v. Huber & Huber Motor Express, 67 F. Supp. 855; Ex parte Nos. MC-2 and MC-3, 28 M.C.C. 125, 133...

FPGA Boot Loader and Scrubber

NASA Technical Reports Server (NTRS)

Wade, Randall S.; Jones, Bailey

2009-01-01

A computer program loads configuration code into a Xilinx field-programmable gate array (FPGA), reads back and verifies that code, reloads the code if an error is detected, and monitors the performance of the FPGA for errors in the presence of radiation. The program consists mainly of a set of VHDL files (wherein "VHDL" signifies "VHSIC Hardware Description Language" and "VHSIC" signifies "very-high-speed integrated circuit").

USSR Report, International Affairs

DTIC Science & Technology

1987-02-11

shown that the cycle "A New Development—Assimilation in Production " has accelerated to practically twice its original speed thanks to these forms of... new production capacities to manufacture hydrodynamic transmissions for scrapers and loaders, and in doing so, will be assisted by a partner—the...creation of new forms of production through joint efforts. Of primary importance in achieving these new forms are mobile and flexible contacts that are in

Conceptual Design of a Robotic Loader System for Remote Missile Launchers.

DTIC Science & Technology

1985-09-01

artifcial intelligence were sur- veyed in order to assess their space applicability and to identify areas which can be developed/adapted to European...such data bases as NTIS and COMPENDEX. The second computer aided search was done through the U. S. Army information services at Redstone Arsenal...Lockheed Corporation. The first DIALOG data base explored was NTIS (National Technical Information Services, U.S. Dept. of Commerce), which contains

Family History of Breast Cancer as a Determinant of the Risk of Developing Endometrial and Ovarian Cancers: A Nationwide Cohort Study

DTIC Science & Technology

2002-01-01

TS, Manley SA, Olopade OI, Cummings S, Garber JE, Bernhardt B, Antman K, Russo D, Wood ME, Mullineau L, Isaacs C, Peshkin B, Buys S, Venne V, Rowley... Antman K, Russo D, Wood ME, Mullineau L, Isaacs C, Peshkin B, Buys S, Venne V, Rowley PT, Loader S, Offit K, Robson M, Hampel H, Brener D, Winer EP

Final Environmental Assessment for a Proposed Pararescue and Combat Rescue Officer Training Campus at Kirtland Air Force Base

DTIC Science & Technology

2006-09-01

tank with adjacent training structure and hoist for inflatable boat training. An indoor climbing wall, a weight/fitness room, and staff and student...climbing; rappelling/litter evacuation; Tyrolean traverses; suspended harness parachuting emergency procedures; aircraft hoist infiltration...characteristics in common. Bulldozers, backhoes, and front-end loaders would be on site throughout periods of excavation and/or site preparation. Dump

Expedient Repair of Structural Facilities (ERSF). Volume 1. ERSF System Development

DTIC Science & Technology

1992-01-01

slabs, will require a different vehicle for transportation; for example a flatbed truck. Specialized equipment, such as the shotcrete machine described in...1) glued, laminated timber (glulam) column insertion and (2) mechanical shoring jack insertion. Both systems were ranked essentially equally after...gage wire mesh; - (optional) 100 rebar ties; and - in some cases, a bulldozer, front-end loader, and flatbed truck. c. Training Since a new piece of

Interpretive computer simulator for the NASA Standard Spacecraft Computer-2 (NSSC-2)

NASA Technical Reports Server (NTRS)

Smith, R. S.; Noland, M. S.

1979-01-01

An Interpretive Computer Simulator (ICS) for the NASA Standard Spacecraft Computer-II (NSSC-II) was developed as a code verification and testing tool for the Annular Suspension and Pointing System (ASPS) project. The simulator is written in the higher level language PASCAL and implented on the CDC CYBER series computer system. It is supported by a metal assembler, a linkage loader for the NSSC-II, and a utility library to meet the application requirements. The architectural design of the NSSC-II is that of an IBM System/360 (S/360) and supports all but four instructions of the S/360 standard instruction set. The structural design of the ICS is described with emphasis on the design differences between it and the NSSC-II hardware. The program flow is diagrammed, with the function of each procedure being defined; the instruction implementation is discussed in broad terms; and the instruction timings used in the ICS are listed. An example of the steps required to process an assembly level language program on the ICS is included. The example illustrates the control cards necessary to assemble, load, and execute assembly language code; the sample program to to be executed; the executable load module produced by the loader; and the resulting output produced by the ICS.

Assessing combined exposures of whole-body vibration and awkward posture--further results from application of a simultaneous field measurement methodology.

PubMed

Raffler, Nastaran; Hermanns, Ingo; Sayn, Detlef; Göres, Benno; Ellegast, Rolf; Rissler, Jörg

2010-01-01

The drivers of ten vehicles (tram, helicopter, saloon car, van, forklift, two mobile excavators, wheel loader, tractor, elevating platform truck) were studied with regard to the combined exposures of whole-body vibration and awkward posture during occupational tasks. Seven degrees of freedom (DOFs), or body angles, were recorded as a function of time by means of the CUELA measuring system (Computer-assisted registration and long-term analysis of musculoskeletal workloads) for the purpose of posture assessment. The vibrational exposure is expressed as the vector sum of the frequency-weighted accelerations in the three Cartesian coordinates; these were recorded simultaneously with the posture measurement. Based upon the percentage of working time spent under different workloads, a scheme is proposed for classification of the two exposures into three categories. In addition, a risk of adverse health effects classified as low, possible or high can be assigned to the combination of the two exposures. With regard to posture, the most severe exposure was measured for the drivers of the wheel loader and for the tractor driver, whereas the lowest exposure was measured for the helicopter pilots and van drivers. With regard to the combination of whole-body and posture exposures, the tractor driver and the elevating platform truck driver exhibited the highest workloads.

Training Materials and Data Requirements for Unit Conduct of Fire Trainer (U-COFT) Training Test Support Plan

DTIC Science & Technology

1980-08-01

DESIGN GROUP I GROUP II GROUP III (XMl Tank) (Chrysler UCOFT) (GE UCOFT) Pretest ...training plan design are that: 1. Tank Commanders and Gunners will have been transition trained on the "MI prior to assign- mint to a test group . Cuirrent...posttests on the XMI for each group . Also, Loaders and Drivers are required for the Group I device pretest , gunnery portion of the

Automated Gun Laying System for Self-Propelled Artillery Weapons.

DTIC Science & Technology

1980-05-30

model designed specifically to the requirements of a test bed system. The system configuration and characteristics were specified through a series of...proposed by the contractor was further defined, utilizing the M109 component information provided by the COTR. Math models were developed to predict system...data. The model used for the TB-I program did not have the capability for a remote reset function, hence it was necessary to instruct the crew (loader

The CRRES Langmuir Probe and Fluxgate Magnetometer Instrument

DTIC Science & Technology

1989-05-09

Gbntract tenager Branch Chief i r FOR THE COWhbDER RITA C. SAGALYN Division Director Qualified requestors may obtain additional copies from the... Computations 73 2.9 Sawtooth Generation 80 2.10 Bias Sweeps 84 2.11 Main Program Loader 96 2.12 Boom Deployment 98 2.13 General Utilities...separated by 100 meters. The other pair of conductors are cylindrical wire boom elements also in the spin plane that are separated by an effective

Apple App Store as a Business Model Supporting U.S. Navy Requirements

DTIC Science & Technology

2011-10-25

credit card identity information for charging the required $99/year fee. Actual payment of the fee is handled by putting the developer program...required for the App Store. Applications are submitted via iTunes Connect (http://itunesconnect.apple.com). Table 1 gives a list of the...still being processed by the iTunes Connect system.  Invalid Binary—Appears when a binary is received through the Application Loader and has been

Radiation Dose Assessment for Military Personnel of the Enewetak Atoll Cleanup Project (1977-1980)

DTIC Science & Technology

2018-04-13

population are detailed. 2.1 Enewetak Atoll Setting Enewetak Atoll (Figure 2) is approximately 23 by 17 statute miles with the long axis running ...Survey and stake the boundaries of soil excision areas; • Remove excess brush; • Excise (scrape surface with bulldozer blade ) the area and...JTGJ-2 and FRST members Survey instruments, soil sampling tools, dump trucks, bucket and backhoe loaders, water tank trucks, scrape blades

2012 ENFORCE. Project Manager Force Projection Briefing to ENFORCE

DTIC Science & Technology

2012-04-16

M-ATV Logistics MRAP Vehicle Systems (Joint Program) •Navistar MaxxPro •GDLS RG-31 •BAE-TVS Caiman •BAE RG-33 SOCOM •BAE RG-33 SOCOM AUV...Handling Equipment • Container Handling Equipment •Loaders • Cranes •Dozers •Excavators Force Sustainment Systems •Cargo Airdrop Systems...Boruff DPM: Mr. Dennis Mazurek Mine Resistant Ambush Protected Vehicles PM: Mr. Carl Owens DPM: COL Jeffrey Carr Tactical

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

INTERIOR VIEW, NORTH QUARRY, LOOKING WEST. IN THE FOREGROUND ON THE FIRST BENCH, POWDER HILLS ARE PRIMED FOR DOLOMITE EXTRACTION. ON THE SECOND BENCH, THE DRILL TEAM IS LAYING OUT THE NEXT SHOTS. ON THE TOP BENCH, A 245 CATERPILLAR LOADER FILLS A 55-TON CATERPILLAR ROCK TRUCK WITH EXTRACTED DOLOMITE FOR TRANSPORT TO THE DOLOMITE CRUSHING AND SCREENING PLANT. - Wade Sand & Gravel Company, North Quarry, State Highway 78, Thomas, Jefferson County, AL

The Ctf18RFC Clamp Loader Is Essential for Telomere Stability in Telomerase-Negative and mre11 Mutant Alleles

PubMed Central

Parke, Courtney; Tatum, Danielle; Lustig, Arthur J.

2014-01-01

The function of the replication clamp loaders in the semi-conservative telomere replication and their relationship to telomerase- and recombination mechanisms of telomere addition remains ambiguous. We have investigated the variant clamp loader Ctf18 RFC (Replication Factor C). To understand the role of Ctf18 at the telomere, we first investigated genetic interactions after loss of Ctf18 and TLC1 (the yeast telomerase RNA). We find that the tlc1▵ ctf18▵ double mutant confers a rapid >1000-fold decrease in viability. The rate of loss was similar to the kinetics of cell death in rad52▵ tlc1▵ cells. However, the Ctf18 pathway is distinct from Rad52, required for the repair of DSBs, as demonstrated by the synthetic lethality of rad52▵ tlc1▵ ctf18▵ triple mutants. These data suggest that each mutant elicits non-redundant defects acting on the same substrate. Second, interactions of the yeast hyper-recombinational mutant, mre11A470T, with ctf18▵ confer a synergistic cold sensitivity. The phenotype of these double mutants ultimately results in telomere loss and the generation of recombinational survivors. We observed a similar synergism between single mutants that led to hypersensitivity to the DNA alkylating agent, methane methyl sulphonate (MMS), the replication fork inhibitor hydroxyurea (HU), and to a failure to separate telomeres of sister chromatids. Hence, ctf18▵ and mre11A470T act in different pathways on telomere substrates for multiple phenotypes. The mre11A470T cells also displayed a DNA damage response (DDR) at 15°C but not at 30°C while ctf18▵ mutants conferred a constitutive DDR activity. Both the 15°C DDR pattern and growth rate were reversible at 30°C and displayed telomerase activity in vivo. We hypothesize that Ctf18 confers protection against stalling and/or breaks at the replication fork in cells that either lack, or are compromised for, telomerase activity. This Ctf18-based function is likely to contribute another level to telomere size homeostasis. PMID:24533124

GIDL: a rule based expert system for GenBank Intelligent Data Loading into the Molecular Biodiversity database

PubMed Central

2012-01-01

Background In the scientific biodiversity community, it is increasingly perceived the need to build a bridge between molecular and traditional biodiversity studies. We believe that the information technology could have a preeminent role in integrating the information generated by these studies with the large amount of molecular data we can find in bioinformatics public databases. This work is primarily aimed at building a bioinformatic infrastructure for the integration of public and private biodiversity data through the development of GIDL, an Intelligent Data Loader coupled with the Molecular Biodiversity Database. The system presented here organizes in an ontological way and locally stores the sequence and annotation data contained in the GenBank primary database. Methods The GIDL architecture consists of a relational database and of an intelligent data loader software. The relational database schema is designed to manage biodiversity information (Molecular Biodiversity Database) and it is organized in four areas: MolecularData, Experiment, Collection and Taxonomy. The MolecularData area is inspired to an established standard in Generic Model Organism Databases, the Chado relational schema. The peculiarity of Chado, and also its strength, is the adoption of an ontological schema which makes use of the Sequence Ontology. The Intelligent Data Loader (IDL) component of GIDL is an Extract, Transform and Load software able to parse data, to discover hidden information in the GenBank entries and to populate the Molecular Biodiversity Database. The IDL is composed by three main modules: the Parser, able to parse GenBank flat files; the Reasoner, which automatically builds CLIPS facts mapping the biological knowledge expressed by the Sequence Ontology; the DBFiller, which translates the CLIPS facts into ordered SQL statements used to populate the database. In GIDL Semantic Web technologies have been adopted due to their advantages in data representation, integration and processing. Results and conclusions Entries coming from Virus (814,122), Plant (1,365,360) and Invertebrate (959,065) divisions of GenBank rel.180 have been loaded in the Molecular Biodiversity Database by GIDL. Our system, combining the Sequence Ontology and the Chado schema, allows a more powerful query expressiveness compared with the most commonly used sequence retrieval systems like Entrez or SRS. PMID:22536971

Radiator debris removing apparatus and work machine using same

DOEpatents

Martin, Kevin L [Washburn, IL; Elliott, Dwight E [Chillicothe, IL

2008-09-02

A radiator assembly includes a finned radiator core and a debris removing apparatus having a compressed air inlet and at least one compressed air outlet configured to direct compressed air through the radiator core. A work machine such as a wheel loader includes a radiator and a debris removing apparatus coupled with on-board compressed air and having at least one pressurized gas outlet configured to direct a gas toward the face of the radiator.

Economic analysis of a small-sized combined heat and power plant using forest biomass in the Republic of Korea

Treesearch

Yeongwan Seo; Han-Sup Han; Edward M. (Ted) Bilek; Jungkee Choi; Dusong Cha; Jungsoo Lee

2017-01-01

Economic analysis was conducted on the feasibility of operating a small-sized (500kW/hour) gasification power plant producing heat and electricity in a rural town surrounded by forests in the Republic of Korea. Cost factors that were considered over the plant’s 20-year life included wood procurement, a wood grab loader, a chipper, a chip dryer, a gasifier, a generator...

Unit Reference Sheet (URS) Cost Methodology.

DTIC Science & Technology

1980-08-01

LAUNCHER MONORAIL GUIDED MISSILE: W/E (NIKE-HERCULES) L45740 LAUNCHER TUBULAR GUIDED MISSILE: (TOW) L45757 LAUNCHER ZERO LENGTH GUIDED MISSILE: (IMP-HAWK...L76762 LOADER TRANSPORTER GUIDED MISSILE: W/E (HAWK) M57503 MOBILE TARGET TRACKING SYSTEM: USED TO SUPPORT MQM 34 ( FIRE BEE) M57549 MOBILITY KIT GUIDED...HIGH RATE THREE BARREL W/E J96479 GUN AUTOMATIC 20 MILLIMETER: GAS OPERATED MANUAL OR ELECT FIRED J96481 GUN AUTOMATIC 20 MILLIMETER: ELECTRIC J96694 GUN

Establishment method of a mixture model and its practical application for transmission gears in an engineering vehicle

NASA Astrophysics Data System (ADS)

Wang, Jixin; Wang, Zhenyu; Yu, Xiangjun; Yao, Mingyao; Yao, Zongwei; Zhang, Erping

2012-09-01

Highly versatile machines, such as wheel loaders, forklifts, and mining haulers, are subject to many kinds of working conditions, as well as indefinite factors that lead to the complexity of the load. The load probability distribution function (PDF) of transmission gears has many distributions centers; thus, its PDF cannot be well represented by just a single-peak function. For the purpose of representing the distribution characteristics of the complicated phenomenon accurately, this paper proposes a novel method to establish a mixture model. Based on linear regression models and correlation coefficients, the proposed method can be used to automatically select the best-fitting function in the mixture model. Coefficient of determination, the mean square error, and the maximum deviation are chosen and then used as judging criteria to describe the fitting precision between the theoretical distribution and the corresponding histogram of the available load data. The applicability of this modeling method is illustrated by the field testing data of a wheel loader. Meanwhile, the load spectra based on the mixture model are compiled. The comparison results show that the mixture model is more suitable for the description of the load-distribution characteristics. The proposed research improves the flexibility and intelligence of modeling, reduces the statistical error and enhances the fitting accuracy, and the load spectra complied by this method can better reflect the actual load characteristic of the gear component.

Structure and Biochemical Activities of Escherichia coli MgsA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Page, Asher N.; George, Nicholas P.; Marceau, Aimee H.

2012-02-27

Bacterial 'maintenance of genome stability protein A' (MgsA) and related eukaryotic enzymes play important roles in cellular responses to stalled DNA replication processes. Sequence information identifies MgsA enzymes as members of the clamp loader clade of AAA{sup +} proteins, but structural information defining the family has been limited. Here, the x-ray crystal structure of Escherichia coli MgsA is described, revealing a homotetrameric arrangement for the protein that distinguishes it from other clamp loader clade AAA{sup +} proteins. Each MgsA protomer is composed of three elements as follows: ATP-binding and helical lid domains (conserved among AAA{sup +} proteins) and a tetramerizationmore » domain. Although the tetramerization domains bury the greatest amount of surface area in the MgsA oligomer, each of the domains participates in oligomerization to form a highly intertwined quaternary structure. Phosphate is bound at each AAA{sup +} ATP-binding site, but the active sites do not appear to be in a catalytically competent conformation due to displacement of Arg finger residues. E. coli MgsA is also shown to form a complex with the single-stranded DNA-binding protein through co-purification and biochemical studies. MgsA DNA-dependent ATPase activity is inhibited by single-stranded DNA-binding protein. Together, these structural and biochemical observations provide insights into the mechanisms of MgsA family AAA{sup +} proteins.« less

Deuterium-Tritium Beta-Layering Within a National Ignition Facility Scale Polymer Target in the LANL Cryogenic Pressure Loader

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ebey, Peter S.; Dole, James M.; Geller, Drew A.

2005-11-15

Beta-layering, the process of beta-decay heat-driven mass redistribution, has been demonstrated in a deuterium-tritium (D-T)-filled polymer sphere of the type required for fusion ignition experiments at the National Ignition Facility. This is the first report, to the best of the authors' knowledge, of a D-T layer formed in a permeation-filled sphere. The 2-mm-diam sphere was filled with D-T by permeation; cooled to cryogenic temperatures while in the high-pressure permeation vessel; and, while cold, removed to an optical axis where the D-T was frozen, melted, and beta-layered in a series of experiments over several weeks' time. This work was performed inmore » the Los Alamos National Laboratory cryogenic pressure loader system. The beta-layering time constant was 24.0 {+-} 2.5 min, less than the theoretical value of 26.8 min, and not showing the significant increase due to build-up of {sup 3}He often observed in beta-layered samples. Supercooling of the liquid D-T was observed. Neither the polymer target nor its tenting material showed visual signs of degradation after 5 weeks of exposure to D-T. Small external thermal gradients were used to shift the D-T material back and forth within the sphere.« less

Slickenside formation by surface melting during the mechanical excavation of rock

NASA Astrophysics Data System (ADS)

Spray, John G.

This work discusses the nature and origin of slickensides generated by the impingement of high-carbon steel teeth on sandstone during the mechanical excavation of boulders by back shovel and front loader. The slickensides show a number of morphological features that can be related to the direction and sense of tooth displacement, including striations, carrot-shaped grooves, curved fractures and steps. Scanning and transmission electron microscopy reveal that the slickensides comprise a layer of Fe-enriched, glass-bonded gouge (≤150 μm thick). The estimated shear stresses and velocities realized at the tooth-rock interface (175 MPa at 1 m s -1 for the back shovel and 100 MPa at 2 m s -1 for the front loader) indicate that a heat production of 150-200 MW m -2 and mean surface temperature of 1400-1700°C were achieved. XRF and microprobe analyses confirm that localized bulk melting and Fe-enrichment of the surface occurred during slip. The excavator-generated slickensides provide an analogue for the effects of a single co-seismic event in the evolution of a shallow, relatively dry fault surface. From a simple consideration of energetics under these conditions, it is apparent that localized surface melting should be commonplace. Such an analogue may be useful as a guide for recognizing melt features in natural slickensides, features that would otherwise tend to be obscured during lengthier periods of interseismic surface modification.

Structure and Biochemical Activities of Escherichia coli MgsA*♦

PubMed Central

Page, Asher N.; George, Nicholas P.; Marceau, Aimee H.; Cox, Michael M.; Keck, James L.

2011-01-01

Bacterial “maintenance of genome stability protein A” (MgsA) and related eukaryotic enzymes play important roles in cellular responses to stalled DNA replication processes. Sequence information identifies MgsA enzymes as members of the clamp loader clade of AAA+ proteins, but structural information defining the family has been limited. Here, the x-ray crystal structure of Escherichia coli MgsA is described, revealing a homotetrameric arrangement for the protein that distinguishes it from other clamp loader clade AAA+ proteins. Each MgsA protomer is composed of three elements as follows: ATP-binding and helical lid domains (conserved among AAA+ proteins) and a tetramerization domain. Although the tetramerization domains bury the greatest amount of surface area in the MgsA oligomer, each of the domains participates in oligomerization to form a highly intertwined quaternary structure. Phosphate is bound at each AAA+ ATP-binding site, but the active sites do not appear to be in a catalytically competent conformation due to displacement of Arg finger residues. E. coli MgsA is also shown to form a complex with the single-stranded DNA-binding protein through co-purification and biochemical studies. MgsA DNA-dependent ATPase activity is inhibited by single-stranded DNA-binding protein. Together, these structural and biochemical observations provide insights into the mechanisms of MgsA family AAA+ proteins. PMID:21297161

Large-Scale Simulation Network Design Study

DTIC Science & Technology

1983-10-01

video displays: three for the tank commander, three for the driver, one for the loader, and one for the gunner. The solid angles subtended by these...Newman Inc Range Sortr This process sorts the expanded display lists into range order for drawing according to the "painter’s algorithm’" The range sorter ...session could then be continued as soon as the network recovered. and the elapsed session time would not be wasted . The SimNet design is much more tolerant

Study and Evaluation of Current and Future Aircraft Loaders

DTIC Science & Technology

1986-08-01

Tigers Airlines JFK Airport , NY 10 Feb 86 Boeing Military Airplane Co. Boeing Commercial Airplane Co. Seattle, WA 11 Feb 86 Korean Airlines LAX, CA 12...Nash Boeing Aircraft Co., Seattle, WA Mr. J. Nelson JFK Airport , NY Mr. P. O’Brien ASD/ENCA Wright-Patterson AFB, OH Mr. C. Outran HQ AFLC/DSTMA...Locations 15 Oct 85 TWA Freight Terminal Laimbert Int’l Airport , St. Louis, mO 22 Nov 85 Lockheed - Georgia Aircraft Co. Marietta, GA 13 Dec 85 Flying

State of the Art for Design and Construction of Sand Compaction Piles

DTIC Science & Technology

1987-11-01

Walz, Headquarters, US Army Corps of Engineers (HQUSACE), was REMR Technical Monitor. The REMR Overview Committee, consisted of Mr. John R. Nikel ... Wire Vibrator Hopper Casing Pipe Air Line Power Line Sand Skip Bucket Front End Loader Figure 2. Typical equipment used to construct a sand...8217~~~~--­ Rubber Packing Wire Inlet for air to close valve and press sand down ..,...__ Air lnl~ot: Figure 5. Special valve used to seal the casing when

Fleet/TYCOM Level Survey of Armament Handling Problems - Task One of the Naval Aviation Armament Support Equipment Program Management Study

DTIC Science & Technology

1977-06-21

7. AUTHOR(#) 6. CONTRACT OR GRANT NUMBER(#) PILA /UDERIAN 9. PERFORMING ORGANIZATION NAME AND ADDRESS 10. PROGRAM ELEMENT. PROJECT, TASK...mechanically complex (i.e. contains an internal combustion engine) and/or comes in direct support of the aircraft is managed and maintained by the AIMD. The...an internal combustion engine. Accordingly, only the Aero 33D/E Trailer, Aero 51B Trailer, 21A/C Bomb Skid, and Aero 47A Weapons Loader are maintained

Safety Analysis of X4 Multi-Tooled Iowa Detonator Loader

DTIC Science & Technology

1980-10-01

D atmosphere. Temperature identification number should be T5.* Personnel Injury Resulting From Machine Incident - Due to the presence of the barricade...ling factor is the yield strength of velostat . 18 the expectancy is 6 x i0-15 accidents per facility hour. Although the spoon is made of phenolic...expression becoms: I- SF (C-2) v (Cv•cp) (xs) (CV,) 2- uthere: C - coefficient of v4riation for the proess ptent’.4 CV% c"of•iclent of variation "or

Manufactured Soil Field Demonstration for Constructing Wetlands to Treat Acid Mine Drainage on Abandoned Minelands

DTIC Science & Technology

2007-11-01

reclamation and reuse of dredged material from existing CDFs. CRDAs have been established with Recycled Soil Manufacturing Technology (RSMT), N-Viro...existing coal mine bony residual waste. Sawdust was loaded into a manure spreader with a front-end loader and spread across the bony residual in...manure spreader and then dredged material was placed on top of the paper fiber. Both 5 ERDC TN-DOER-D9 November 2007 materials were then spread

Notes on Fire on Aeroplanes

DTIC Science & Technology

1917-08-01

To extract a cartridge or a cartridge case, put the rammer in the muzzle of gun and knock with the head of the rammer on the fuse of the projectile...or on the base of the case. If it is a cartridge which is being extracted ! the loader, standing at the breech, receives it in both hands. (f) Give...fuses and charges. They should be tried in the loading position (incline the gun slightly, open the breech gently, and extract the cartridge with

Electrostatic Interactions at the Dimer Interface Stabilize the E. coli β Sliding Clamp.

PubMed

Purohit, Anirban; England, Jennifer K; Douma, Lauren G; Tondnevis, Farzaneh; Bloom, Linda B; Levitus, Marcia

2017-08-22

Sliding clamps are ring-shaped oligomeric proteins that encircle DNA and associate with DNA polymerases for processive DNA replication. The dimeric Escherichia coli β-clamp is closed in solution but must adopt an open conformation to be assembled onto DNA by a clamp loader. To determine what factors contribute to the stability of the dimer interfaces in the closed conformation and how clamp dynamics contribute to formation of the open conformation, we identified conditions that destabilized the dimer and measured the effects of these conditions on clamp dynamics. We characterized the role of electrostatic interactions in stabilizing the β-clamp interface. Increasing salt concentration results in decreased dimer stability and faster subunit dissociation kinetics. The equilibrium dissociation constant of the dimeric clamp varies with salt concentration as predicted by simple charge-screening models, indicating that charged amino acids contribute to the remarkable stability of the interface at physiological salt concentrations. Mutation of a charged residue at the interface (Arg-103) weakens the interface significantly, whereas effects are negligible when a hydrophilic (Ser-109) or a hydrophobic (Ile-305) amino acid is mutated instead. It has been suggested that clamp opening by the clamp loader takes advantage of spontaneous opening-closing fluctuations at the clamp's interface, but our time-resolved fluorescence and fluorescence correlation experiments rule out conformational fluctuations that lead to a significant fraction of open states. Copyright © 2017 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Factors in daily physical activity related to calcaneal mineral density in men.

PubMed

Hutchinson, T M; Whalen, R T; Cleek, T M; Vogel, J M; Arnaud, S B

1995-05-01

To determine the factors in daily physical activity that influence the mineral density of the calcaneus, we recorded walking steps and the type and duration of exercise in 43 healthy 26-to 51-yr-old men. Areal (g.cm-2) calcaneal bone mineral density (CBMD) was measured by single energy x-ray densitometry (SXA, Osteon, Inc., Wahiawa, HI). Subjects walked a mean (+/- SD) of 7902 (+/- 2534) steps per day or approximately 3.9 (+/- 1.2) miles daily. Eight subjects reported no exercise activities. The remaining 35 subjects spent 143 (2-772) (median and range) min.wk-1 exercising. Twenty-eight men engaged in exercise activities that generate single leg peak vertical ground reaction forces (GRFz) of 2 or more body weights (high loaders, HL), and 15 reported exercise or daily activities that typically generate GRFz less than 1.5 body weights (low loaders, LL). CBMD was 12% higher in HL than LL (0.668 +/- 0.074 g.cm-2 vs 0.597 +/- 0.062 g.cm-2, P < 0.004). In the HL group, CBMD correlated to reported minutes of high load exercise (r = 0.41, P < 0.03). CBMD was not related to the number of daily walking steps (N = 43, r = 0.03, NS). The results of this study support the concept that the dominant factor in daily physical activity relating to bone mineral density is the participation in site specific high loading activities, i.e., for the calcaneus, high calcaneal loads.

Factors in Daily Physical Activity Related to Calcaneal Mineral Density in Men

NASA Technical Reports Server (NTRS)

Hutchinson, Teresa M.; Whalen, Robert T.; Cleek, Tammy M.; Vogel, John M.; Arnaud, Sara B.

1995-01-01

To determine the factors in daily physical activity that influence the mineral density of the calcaneus, we recorded walking steps and the type and duration of exercise in 43 healthy 26-to 51-yr-old men. Areal (g/sq cm) calcaneal bone mineral density (CBMD) was measured by single energy x-ray densitometry. Subjects walked a mean (+/- SD) of 7902(+/-2534) steps per day or approximately 3.9(+/-1.2) miles daily. Eight subjects reported no exercise activities. The remaining 35 subjects spent 143(2-772) (median and range) min/wk exercising. Twenty-eight men engaged in exercise activities that generate single leg peak vertical ground reaction forces (GRF(sub z)) of 2 or more body weights (high loaders, HL), and 15 reported exercise or daily activities that typically generate GRF(sub z) less than 1.5 body weights (low loaders, LL). CBMD was 12% higher in HL than LL (0.668 +/- 0.074 g/sq cm vs 0.597 +/- 0.062 g/sq cm, P less than 0.004). In the HL group, CBMD correlated to reported minutes of high load exercise (r = 0.41, P less than 0.03). CBMD was not related to the number of daily walking steps (N = 43, r = 0.03, NS). The results of this study support the concept that the dominant factor in daily physical activity relating to bone mineral density is the participation in site specific high loading activities, i.e., for the calcaneus, high calcaneal loads.

Apoplastic and symplastic phloem loading in Quercus robur and Fraxinus excelsior

PubMed Central

Lohaus, Gertrud

2014-01-01

Whereas most of the research on phloem loading is performed on herbaceous plants, less is known about phloem loading strategies in trees. In this study, the phloem loading mechanisms of Quercus robur and Fraxinus excelsior were analysed. The following features were examined: the minor vein structure, the sugar concentrations in phloem sap by the laser–aphid–stylet technique, the distribution of photoassimilates in the mesophyll cells by non-aqueous fractionation, gradients of sugar concentrations and osmotic pressure, and the expression of sucrose transporters. The minor vein configurations of Q. robur and F. excelsior belong to the open type. Quercus robur contained companion cells in the minor veins whereas F. excelsior showed intermediary cells in addition to ordinary companion cells. The main carbon transport form in Q. robur was sucrose (~1M). In F. excelsior high amounts of raffinose and stachyose were also transported. However, in both tree species, the osmolality of phloem sap was higher than the osmolality of the mesophyll cells. The concentration gradients between phloem sap and the cytoplasm of mesophyll cells for sucrose were 16-fold and 14-fold for Q. robur and F. excelsior, respectively. Independent of the type of translocated sugars, sucrose transporter cDNAs were cloned from both species. The results indicate that phloem loading of sucrose and other metabolites must involve active loading steps in both tree species. Quercus robur seems to be an apoplastic phloem loader while F. excelsior shows indications of being a symplastic or mixed symplastic–apoplastic phloem loader. PMID:24591056

Muscle-spring dynamics in time-limited, elastic movements.

PubMed

Rosario, M V; Sutton, G P; Patek, S N; Sawicki, G S

2016-09-14

Muscle contractions that load in-series springs with slow speed over a long duration do maximal work and store the most elastic energy. However, time constraints, such as those experienced during escape and predation behaviours, may prevent animals from achieving maximal force capacity from their muscles during spring-loading. Here, we ask whether animals that have limited time for elastic energy storage operate with springs that are tuned to submaximal force production. To answer this question, we used a dynamic model of a muscle-spring system undergoing a fixed-end contraction, with parameters from a time-limited spring-loader (bullfrog: Lithobates catesbeiana) and a non-time-limited spring-loader (grasshopper: Schistocerca gregaria). We found that when muscles have less time to contract, stored elastic energy is maximized with lower spring stiffness (quantified as spring constant). The spring stiffness measured in bullfrog tendons permitted less elastic energy storage than was predicted by a modelled, maximal muscle contraction. However, when muscle contractions were modelled using biologically relevant loading times for bullfrog jumps (50 ms), tendon stiffness actually maximized elastic energy storage. In contrast, grasshoppers, which are not time limited, exhibited spring stiffness that maximized elastic energy storage when modelled with a maximal muscle contraction. These findings demonstrate the significance of evolutionary variation in tendon and apodeme properties to realistic jumping contexts as well as the importance of considering the effect of muscle dynamics and behavioural constraints on energy storage in muscle-spring systems. © 2016 The Author(s).

Soviet Union, Military Affairs. Data, Diagrams of Ground Forces Weaponry.

DTIC Science & Technology

1987-07-16

roadless areas at speeds of up to 10 -20 kilometers per hour. And now, something about the gun’s design. I shall name its main parts and indi- cate their...27.4 ■ kilograms. At the prescribed rate of fire, which is six rounds per minute, the loader must "move" 10 poods of metal every 60 seconds. This...It is 600 rounds per minute for the AKM. When the tregger is pressed the shots occur one after another, every 0.1 second. This means that 10

John F. Kennedy Space Center's Wireless Hang Angle Instrumentation System

NASA Technical Reports Server (NTRS)

Kohler, Jeff

2009-01-01

The technology is a high-precision, wireless inclinometer. The system was designed for monitoring the suspension angle of the Orbiter vehicle during loading onto the Solid Rocket Boosters of the Space Shuttle. Originally, operators manually measured the alignment of the Orbiter with a hand-held inclinometer on a nonrigid surface. The measurement was open to interpretation by the loader. If the Orbiter is misaligned, it can crush ball joints and delay the loading while repairs are made. With this system, the Orbiter can be loaded without damage and without manual measurement.

Department of the Army Justification of Estimates for Fiscal Year 1984, Procurement Appropriations-Construction Program Submitted to Congress January 1983.

DTIC Science & Technology

1983-01-01

unloaded through the bottom discharge gates of the railtoad cars, into a portable conveyor , to a front end loader and then to the pile. A bulldozer than...locomotive to move the cars. At the Powerhouse, the coal is unloaded througb the railroad car discharge gates and into a bucket conveyor that carries the...structures by design are semi-permanent, i.e., they can be dismantled andelastalled elsewhere. Protection must be provided for these structures. P# : a

JPRS Report, Soviet Union, Military Affairs

DTIC Science & Technology

1990-11-30

Ptichkin] I need to say that little is known about this the levers of a T -34 in June 1941. I fought, burned, and vehicle. And, even to this day, it, like its...immediately tasked me to head work to design a An automatic gun loader was installed on the new tank prime mover based on the T -54 medium tank. I ... I They have rashly approached this very conversion [pro- have in mind the T -72 which is well known both in the cess] in the sector, putting it mildly

47. View looking east. In the ground at center left, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

47. View looking east. In the ground at center left, a top crib back member of the 'out-rigger' is visible. This member was accidentally revealed by a back loader. The revealed timber is not the top of the crib, as it is notched for another course. The top level of the lock could have been nearly equal to the modern U.S. 24 road surface. - Wabash & Erie Canal, Lock No. 2, 8 miles east of Fort Wayne, adjacent to U.S. Route 24, New Haven, Allen County, IN

Proceedings of the National Workshop on Containment Area Aquaculture Held in South Padre Island, Texas on 11-15 November 1991

DTIC Science & Technology

1993-12-01

Signifi- and risk . cant capital replacement is also required for the boat, motor, and trailer needed to tend the "* Cost of acquiring waterfront property...after Barge & Shaker 1,800 Front-end Loader & Pump 950 depreciation and opportunity costs (Table 6). Fuel and Oil This high IRR reflects the "favorable...Long-term loan payment: Interest 5,722 Operating loan payment: Interest 0 Depreciation 10,044 Net returns to owner’s capital, management and risk

InterMine Webservices for Phytozome (Rev2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlson, Joseph; Goodstein, David; Rokhsar, Dan

2014-07-10

A datawarehousing framework for information provides a useful infrastructure for providers and users of genomic data. For providers, the infrastructure give them a consistent mechanism for extracting raw data. While for the users, the web services supported by the software allows them to make complex, and often unique, queries of the data. Previously, phytozome.net used BioMart to provide the infrastructure. As the complexity, scale and diversity of the dataset as grown, we decided to implement an InterMine web service on our servers. This change was largely motivated by the ability to have a more complex table structure and richer webmore » reporting mechanism than BioMart. For InterMine to achieve its more complex database schema it requires an XML description of the data and an appropriate loader. Unlimited one-to-many and many-to-many relationship between the tables can be enabled in the schema. We have implemented support for:1.) Genomes and annotations for the data in Phytozome. This set is the 48 organisms currently stored in a back end CHADO datastore. The data loaders are modified versions of the CHADO data adapters from FlyMine. 2.) Interproscan results from all proteins in the Phytozome database. 3.) Clusters of proteins into a grouped heirarchically by similarity. 4.) Cufflinks results from tissue-specific RNA-Seq data of Phytozome organisms. 5.) Diversity data (GATK and SnpEFF results) from a set of individual organism. The last two datatypes are new in this implementation of our web services. We anticipate that the scale of these data will increase considerably in the near future.« less

Reversed electrogenic sodium bicarbonate cotransporter 1 is the major acid loader during recovery from cytosolic alkalosis in mouse cortical astrocytes

PubMed Central

Theparambil, Shefeeq M; Naoshin, Zinnia; Thyssen, Anne; Deitmer, Joachim W

2015-01-01

Recovery of intracellular pH from cytosolic alkalosis has been attributed primarily to Cl– coupled acid loaders/base extruders such as Cl–/HCO3– or Cl–/OH– exchangers. We have studied this process in cortical astrocytes from wild-type and transgenic mouse models with gene deletion for the electrogenic sodium bicarbonate cotransporter 1 (NBCe1) and for carbonic anhydrase (CA) isoform II. An acute cytosolic alkalosis was induced by the removal of either CO2/HCO3– or butyric acid, and the subsequent acid loading was analysed by monitoring changes in cytosolic H+ or Na+ using ion-sensitive fluorescent dyes. We have identified that NBCe1 reverses during alkalosis and contributes more than 70% to the rate of recovery from alkalosis by extruding Na+ and HCO3–. After CA inhibition or in CAII-knockout (KO) cells, the rate of recovery was reduced by 40%, and even by 70% in the nominal absence of CO2/HCO3–. Increasing the extracellular K+ concentration modulated the rate of acid loading in wild-type cells, but not in NBCe1-KO cells. Removing chloride had only a minor effect on the recovery from alkalosis. Reversal of NBCe1 by reducing pH/[HCO3–] was demonstrated in astrocytes and in Xenopus oocytes, in which human NBCe1 was heterologously expressed. The results obtained suggest that reversed NBCe1, supported by CAII activity, plays a major role in acid-loading cortical astrocytes to support recovery from cytosolic alkalosis. PMID:25990710

In Vivo Quantification of Cell Coupling in Plants with Different Phloem-Loading Strategies[W][OA

PubMed Central

Liesche, Johannes; Schulz, Alexander

2012-01-01

Uptake of photoassimilates into the leaf phloem is the key step in carbon partitioning and phloem transport. Symplasmic and apoplasmic loading strategies have been defined in different plant taxa based on the abundance of plasmodesmata between mesophyll and phloem. For apoplasmic loading to occur, an absence of plasmodesmata is a sufficient but not a necessary criterion, as passage of molecules through plasmodesmata might well be blocked or restricted. Here, we present a noninvasive, whole-plant approach to test symplasmic coupling and quantify the intercellular flux of small molecules using photoactivation microscopy. Quantification of coupling between all cells along the prephloem pathways of the apoplasmic loader Vicia faba and Nicotiana tabacum showed, to our knowledge for the first time in vivo, that small solutes like sucrose can diffuse through plasmodesmata up to the phloem sieve element companion cell complex (SECCC). As expected, the SECCC was found to be symplasmically isolated for small solutes. In contrast, the prephloem pathway of the symplasmic loader Cucurbita maxima was found to be well coupled with the SECCC. Phloem loading in gymnosperms is not well understood, due to a profoundly different leaf anatomy and a scarcity of molecular data compared with angiosperms. A cell-coupling analysis for Pinus sylvestris showed high symplasmic coupling along the entire prephloem pathway, comprising at least seven cell border interfaces between mesophyll and sieve elements. Cell coupling together with measurements of leaf sap osmolality indicate a passive symplasmic loading type. Similarities and differences of this loading type with that of angiosperm trees are discussed. PMID:22422939

Final Environmental Impact Statement for Proposed Barry M. Goldwater Range East Range Enhancements and Record of Decision for the Barry M. Goldwater Range East Range Enhancements, Final Environmental Impact Statement Dated November 26, 2010

DTIC Science & Technology

2014-09-25

Unemployment rates in Yuma County have been historically high due to seasonal employment within the agriculture sector . In 2000, the San Lucy District of the...loader and where trees along the banks of the washes can be avoided. The source sites are highly ephemeral washes that are normally dry and flow only... Sector General Permit for the proposed sand and gravel operations. Water Resources Environmental Consequences: Effects on water resources are mostly

Potential Application of BIOMASS Technology at National Space Technology Laboratories and Mississippi Army Ammunition Plant.

DTIC Science & Technology

1980-02-01

fuel. Based on the survey data, wood chips in the NSTL area are sold for $13 to $16 per wet ton ($14 to $18 Der l03 kg wet), bark for $6 to $7 per wet...truck 3 Chip vans (initially) 1 Pickup (3/4 ton) 1 Front-end loader (for handling at chip pile) This equipment combination assumes all material ]-inch...ing sites in chip vans , preferably with live-beds to aid in unloading. At the processing site the chips would be stored in large piles. A Front-end

Training Effectiveness Study of Simulator Usage and Its Impact on Live Fire Armor Gunnery

DTIC Science & Technology

2014-06-01

including artillery  Round loading and reloading sounds  Loader’s “UP”  Main gun , M240, and M2 machine gun firing  Track clatter  Engine and...functional  TC’s hatch will not open  M2 machine gun is not replicated on the AGTS  Not all circuit breakers are supported from the display panels 18...Driver’s and loader’s stations are not simulated Of the limitations listed above, three are of most concern: the lack of M2 machine gun

Assessment and analysis of noise levels in and around Ib river coalfield, Orissa, India.

PubMed

Mohapatra, Haraprasad; Goswami, Shreerup

2012-05-01

Heavy earth moving machineries, different capacities of dumpers and loaders, blasting and drilling make the mining environment noisy. A study was carried out to assess the noise level in different opencast projects in and around Belpahar and Brajarajnagar areas of Ib river coalfield. Noise assessment was carried out in various residential, commercial and industrial places. The noise levels, especially L(eq) values of different wheel loaders, dumpers, shovel and crusher units were also assessed and were more than permissible limit (90dB) in some of their operating conditions. Sound ressure level measurements while drilling into coal and overburden at Lakhanpur opencast project yielded noise levels (L(eq)) of 81.33 to 96.2 dB. Thus, these L(eq) values of drilling machines in most of the operating conditions were above permissible limit. The average noise intensities (6 a.m.-10 p.m.: 51.6-60.875dB and 10 p.m.-6 a.m.: 42.6-49.8dB) and L(eq) values (6 a.m.-10 p.m.: 50.9-67.0dB and 10 p.m.-6 a.m.: 40.8-53.3dB) during both day and night time of the residential areas around the Ib river coalfield were in close proximity or beyond the permissible limit. The L(eq) values at some of the commercial and industrial places were beyond (6 a.m.-10 p.m.: 61.6-88.3 dB and 10 p.m.-6 a.m.: 55.4-64.8dB) permissible limit. However, in most of the cases, the L(max) noise values were more (6 a.m.-10 p.m.: 68.5-91.4 dB and 10 p.m.-6 a.m.: 69.3-76.4dB) than the permissible limit. Analysis of variance was also computed for heavy earth moving machineries in different operating conditions and also for different residential, commercial and industrial places to infer the level of significance. The difference of noise intensity produced by different wheel loaders at Lakhanpur and Lilari opencast projects, drilling machines at Lakhanpur opencast project, 50 tons capacity dumpers at various conditions of Ib river coalfield within the same operating condition was significant at both 5% and 1% levels of significance. Similarly, the variance of estimated noise level in residential places during day time and commercial and industrial places during day and night time was significant at both 5% and 1% levels of significance. Moreover, a preliminary survey adopting questionnaire method amongst the mine workers and local inhabitants was also carried out to evaluate their perception about the mining related noise.

Tripal v1.1: a standards-based toolkit for construction of online genetic and genomic databases.

PubMed

Sanderson, Lacey-Anne; Ficklin, Stephen P; Cheng, Chun-Huai; Jung, Sook; Feltus, Frank A; Bett, Kirstin E; Main, Dorrie

2013-01-01

Tripal is an open-source freely available toolkit for construction of online genomic and genetic databases. It aims to facilitate development of community-driven biological websites by integrating the GMOD Chado database schema with Drupal, a popular website creation and content management software. Tripal provides a suite of tools for interaction with a Chado database and display of content therein. The tools are designed to be generic to support the various ways in which data may be stored in Chado. Previous releases of Tripal have supported organisms, genomic libraries, biological stocks, stock collections and genomic features, their alignments and annotations. Also, Tripal and its extension modules provided loaders for commonly used file formats such as FASTA, GFF, OBO, GAF, BLAST XML, KEGG heir files and InterProScan XML. Default generic templates were provided for common views of biological data, which could be customized using an open Application Programming Interface to change the way data are displayed. Here, we report additional tools and functionality that are part of release v1.1 of Tripal. These include (i) a new bulk loader that allows a site curator to import data stored in a custom tab delimited format; (ii) full support of every Chado table for Drupal Views (a powerful tool allowing site developers to construct novel displays and search pages); (iii) new modules including 'Feature Map', 'Genetic', 'Publication', 'Project', 'Contact' and the 'Natural Diversity' modules. Tutorials, mailing lists, download and set-up instructions, extension modules and other documentation can be found at the Tripal website located at http://tripal.info. DATABASE URL: http://tripal.info/.

Tripal v1.1: a standards-based toolkit for construction of online genetic and genomic databases

PubMed Central

Sanderson, Lacey-Anne; Ficklin, Stephen P.; Cheng, Chun-Huai; Jung, Sook; Feltus, Frank A.; Bett, Kirstin E.; Main, Dorrie

2013-01-01

Tripal is an open-source freely available toolkit for construction of online genomic and genetic databases. It aims to facilitate development of community-driven biological websites by integrating the GMOD Chado database schema with Drupal, a popular website creation and content management software. Tripal provides a suite of tools for interaction with a Chado database and display of content therein. The tools are designed to be generic to support the various ways in which data may be stored in Chado. Previous releases of Tripal have supported organisms, genomic libraries, biological stocks, stock collections and genomic features, their alignments and annotations. Also, Tripal and its extension modules provided loaders for commonly used file formats such as FASTA, GFF, OBO, GAF, BLAST XML, KEGG heir files and InterProScan XML. Default generic templates were provided for common views of biological data, which could be customized using an open Application Programming Interface to change the way data are displayed. Here, we report additional tools and functionality that are part of release v1.1 of Tripal. These include (i) a new bulk loader that allows a site curator to import data stored in a custom tab delimited format; (ii) full support of every Chado table for Drupal Views (a powerful tool allowing site developers to construct novel displays and search pages); (iii) new modules including ‘Feature Map’, ‘Genetic’, ‘Publication’, ‘Project’, ‘Contact’ and the ‘Natural Diversity’ modules. Tutorials, mailing lists, download and set-up instructions, extension modules and other documentation can be found at the Tripal website located at http://tripal.info. Database URL: http://tripal.info/ PMID:24163125

Similar photosynthetic response to elevated carbon dioxide concentration in species with different phloem loading strategies.

PubMed

Bishop, Kristen A; Lemonnier, Pauline; Quebedeaux, Jennifer C; Montes, Christopher M; Leakey, Andrew D B; Ainsworth, Elizabeth A

2018-06-02

Species have different strategies for loading sugars into the phloem, which vary in the route that sugars take to enter the phloem and the energetics of sugar accumulation. Species with passive phloem loading are hypothesized to have less flexibility in response to changes in some environmental conditions because sucrose export from mesophyll cells is dependent on fixed anatomical plasmodesmatal connections. Passive phloem loaders also have high mesophyll sugar content, and may be less likely to exhibit sugar-mediated down-regulation of photosynthetic capacity at elevated CO 2 concentrations. To date, the effect of phloem loading strategy on the response of plant carbon metabolism to rising atmospheric CO 2 concentrations is unclear, despite the widespread impacts of rising CO 2 on plants. Over three field seasons, five species with apoplastic loading, passive loading, or polymer-trapping were grown at ambient and elevated CO 2 concentration in free air concentration enrichment plots. Light-saturated rate of photosynthesis, photosynthetic capacity, leaf carbohydrate content, and anatomy were measured and compared among the species. All five species showed significant stimulation in midday photosynthetic CO 2 uptake by elevated CO 2 even though the two passive loading species showed significant down-regulation of maximum Rubisco carboxylation capacity at elevated CO 2 . There was a trend toward greater starch accumulation at elevated CO 2 in all species, and was most pronounced in passive loaders. From this study, we cannot conclude that phloem loading strategy is a key determinant of plant response to elevated CO 2 , but compelling differences in response counter to our hypothesis were observed. A phylogenetically controlled experiment with more species may be needed to fully test the hypothesis.

A scalable database model for multiparametric time series: a volcano observatory case study

NASA Astrophysics Data System (ADS)

Montalto, Placido; Aliotta, Marco; Cassisi, Carmelo; Prestifilippo, Michele; Cannata, Andrea

2014-05-01

The variables collected by a sensor network constitute a heterogeneous data source that needs to be properly organized in order to be used in research and geophysical monitoring. With the time series term we refer to a set of observations of a given phenomenon acquired sequentially in time. When the time intervals are equally spaced one speaks of period or sampling frequency. Our work describes in detail a possible methodology for storage and management of time series using a specific data structure. We designed a framework, hereinafter called TSDSystem (Time Series Database System), in order to acquire time series from different data sources and standardize them within a relational database. The operation of standardization provides the ability to perform operations, such as query and visualization, of many measures synchronizing them using a common time scale. The proposed architecture follows a multiple layer paradigm (Loaders layer, Database layer and Business Logic layer). Each layer is specialized in performing particular operations for the reorganization and archiving of data from different sources such as ASCII, Excel, ODBC (Open DataBase Connectivity), file accessible from the Internet (web pages, XML). In particular, the loader layer performs a security check of the working status of each running software through an heartbeat system, in order to automate the discovery of acquisition issues and other warning conditions. Although our system has to manage huge amounts of data, performance is guaranteed by using a smart partitioning table strategy, that keeps balanced the percentage of data stored in each database table. TSDSystem also contains modules for the visualization of acquired data, that provide the possibility to query different time series on a specified time range, or follow the realtime signal acquisition, according to a data access policy from the users.

A multidisciplinary database for geophysical time series management

NASA Astrophysics Data System (ADS)

Montalto, P.; Aliotta, M.; Cassisi, C.; Prestifilippo, M.; Cannata, A.

2013-12-01

The variables collected by a sensor network constitute a heterogeneous data source that needs to be properly organized in order to be used in research and geophysical monitoring. With the time series term we refer to a set of observations of a given phenomenon acquired sequentially in time. When the time intervals are equally spaced one speaks of period or sampling frequency. Our work describes in detail a possible methodology for storage and management of time series using a specific data structure. We designed a framework, hereinafter called TSDSystem (Time Series Database System), in order to acquire time series from different data sources and standardize them within a relational database. The operation of standardization provides the ability to perform operations, such as query and visualization, of many measures synchronizing them using a common time scale. The proposed architecture follows a multiple layer paradigm (Loaders layer, Database layer and Business Logic layer). Each layer is specialized in performing particular operations for the reorganization and archiving of data from different sources such as ASCII, Excel, ODBC (Open DataBase Connectivity), file accessible from the Internet (web pages, XML). In particular, the loader layer performs a security check of the working status of each running software through an heartbeat system, in order to automate the discovery of acquisition issues and other warning conditions. Although our system has to manage huge amounts of data, performance is guaranteed by using a smart partitioning table strategy, that keeps balanced the percentage of data stored in each database table. TSDSystem also contains modules for the visualization of acquired data, that provide the possibility to query different time series on a specified time range, or follow the realtime signal acquisition, according to a data access policy from the users.

Passive phloem loading and long-distance transport in a synthetic tree-on-a-chip.

PubMed

Comtet, Jean; Jensen, Kaare H; Turgeon, Robert; Stroock, Abraham D; Hosoi, A E

2017-03-20

Vascular plants rely on differences in osmotic pressure to export sugars from regions of synthesis (mature leaves) to sugar sinks (roots, fruits). In this process, known as Münch pressure flow, the loading of sugars from photosynthetic cells to the export conduit (the phloem) is crucial, as it sets the pressure head necessary to power long-distance transport. Whereas most herbaceous plants use active mechanisms to increase phloem sugar concentration above that of the photosynthetic cells, in most tree species, for which transport distances are largest, loading seems, counterintuitively, to occur by means of passive symplastic diffusion from the mesophyll to the phloem. Here, we use a synthetic microfluidic model of a passive loader to explore the non-linear dynamics that arise during export and determine the ability of passive loading to drive long-distance transport. We first demonstrate that in our device, the phloem concentration is set by the balance between the resistances to diffusive loading from the source and convective export through the phloem. Convection-limited export corresponds to classical models of Münch transport, where the phloem concentration is close to that of the source; in contrast, diffusion-limited export leads to small phloem concentrations and weak scaling of flow rates with hydraulic resistance. We then show that the effective regime of convection-limited export is predominant in plants with large transport resistances and low xylem pressures. Moreover, hydrostatic pressures developed in our synthetic passive loader can reach botanically relevant values as high as 10 bars. We conclude that passive loading is sufficient to drive long-distance transport in large plants, and that trees are well suited to take full advantage of passive phloem loading strategies.

Rv0004 is a new essential member of the mycobacterial DNA replication machinery

PubMed Central

Hooppaw, Anna J.; Richardson, Kirill; Lee, Hark Joon; Kimmey, Jacqueline M.; Aldridge, Bree B.

2017-01-01

DNA replication is fundamental for life, yet a detailed understanding of bacterial DNA replication is limited outside the organisms Escherichia coli and Bacillus subtilis. Many bacteria, including mycobacteria, encode no identified homologs of helicase loaders or regulators of the initiator protein DnaA, despite these factors being essential for DNA replication in E. coli and B. subtilis. In this study we discover that a previously uncharacterized protein, Rv0004, from the human pathogen Mycobacterium tuberculosis is essential for bacterial viability and that depletion of Rv0004 leads to a block in cell cycle progression. Using a combination of genetic and biochemical approaches, we found that Rv0004 has a role in DNA replication, interacts with DNA and the replicative helicase DnaB, and affects DnaB-DnaA complex formation. We also identify a conserved domain in Rv0004 that is predicted to structurally resemble the N-terminal protein-protein interaction domain of DnaA. Mutation of a single conserved tryptophan within Rv0004’s DnaA N-terminal-like domain leads to phenotypes similar to those observed upon Rv0004 depletion and can affect the association of Rv0004 with DnaB. In addition, using live cell imaging during depletion of Rv0004, we have uncovered a previously unappreciated role for DNA replication in coordinating mycobacterial cell division and cell size. Together, our data support that Rv0004 encodes a homolog of the recently identified DciA family of proteins found in most bacteria that lack the DnaC-DnaI helicase loaders in E. coli and B. subtilis. Therefore, the mechanisms of Rv0004 elucidated here likely apply to other DciA homologs and reveal insight into the diversity of bacterial strategies in even the most conserved biological processes. PMID:29176877

Estimating Energy Consumption of Mobile Fluid Power in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lynch, Lauren; Zigler, Bradley T.

This report estimates the market size and energy consumption of mobile off-road applications utilizing hydraulic fluid power, and summarizes technology gaps and implementation barriers. Mobile fluid power is the use of hydraulic fluids under pressure to transmit power in mobile equipment applications. The mobile off-road fluid power sector includes various uses of hydraulic fluid power equipment with fundamentally diverse end-use application and operational requirements, such as a skid steer loader, a wheel loader or an agriculture tractor. The agriculture and construction segments dominate the mobile off-road fluid power market in component unit sales volume. An estimated range of energy consumedmore » by the mobile off-road fluid power sector is 0.36 - 1.8 quads per year, which was 1.3 percent - 6.5 percent of the total energy consumed in 2016 by the transportation sector. Opportunities for efficiency improvements within the fluid power system result from needs to level and reduce the peak system load requirements and develop new technologies to reduce fluid power system level losses, both of which may be facilitated by characterizing duty cycles to define standardized performance test methods. There are currently no commonly accepted standardized test methods for evaluating equipment level efficiency over a duty cycle. The off-road transportation sector currently meets criteria emissions requirements, and there are no efficiency regulations requiring original equipment manufacturers (OEM) to invest in new architecture development to improve the fuel economy of mobile off-road fluid power systems. In addition, the end-user efficiency interests are outweighed by low equipment purchase or lease price concerns, required payback periods, and reliability and durability requirements of new architecture. Current economics, low market volumes with high product diversity, and regulation compliance challenge OEM investment in commercialization of new architecture development.« less

BioWarehouse: a bioinformatics database warehouse toolkit

PubMed Central

Lee, Thomas J; Pouliot, Yannick; Wagner, Valerie; Gupta, Priyanka; Stringer-Calvert, David WJ; Tenenbaum, Jessica D; Karp, Peter D

2006-01-01

Background This article addresses the problem of interoperation of heterogeneous bioinformatics databases. Results We introduce BioWarehouse, an open source toolkit for constructing bioinformatics database warehouses using the MySQL and Oracle relational database managers. BioWarehouse integrates its component databases into a common representational framework within a single database management system, thus enabling multi-database queries using the Structured Query Language (SQL) but also facilitating a variety of database integration tasks such as comparative analysis and data mining. BioWarehouse currently supports the integration of a pathway-centric set of databases including ENZYME, KEGG, and BioCyc, and in addition the UniProt, GenBank, NCBI Taxonomy, and CMR databases, and the Gene Ontology. Loader tools, written in the C and JAVA languages, parse and load these databases into a relational database schema. The loaders also apply a degree of semantic normalization to their respective source data, decreasing semantic heterogeneity. The schema supports the following bioinformatics datatypes: chemical compounds, biochemical reactions, metabolic pathways, proteins, genes, nucleic acid sequences, features on protein and nucleic-acid sequences, organisms, organism taxonomies, and controlled vocabularies. As an application example, we applied BioWarehouse to determine the fraction of biochemically characterized enzyme activities for which no sequences exist in the public sequence databases. The answer is that no sequence exists for 36% of enzyme activities for which EC numbers have been assigned. These gaps in sequence data significantly limit the accuracy of genome annotation and metabolic pathway prediction, and are a barrier for metabolic engineering. Complex queries of this type provide examples of the value of the data warehousing approach to bioinformatics research. Conclusion BioWarehouse embodies significant progress on the database integration problem for bioinformatics. PMID:16556315

BioWarehouse: a bioinformatics database warehouse toolkit.

PubMed

Lee, Thomas J; Pouliot, Yannick; Wagner, Valerie; Gupta, Priyanka; Stringer-Calvert, David W J; Tenenbaum, Jessica D; Karp, Peter D

2006-03-23

This article addresses the problem of interoperation of heterogeneous bioinformatics databases. We introduce BioWarehouse, an open source toolkit for constructing bioinformatics database warehouses using the MySQL and Oracle relational database managers. BioWarehouse integrates its component databases into a common representational framework within a single database management system, thus enabling multi-database queries using the Structured Query Language (SQL) but also facilitating a variety of database integration tasks such as comparative analysis and data mining. BioWarehouse currently supports the integration of a pathway-centric set of databases including ENZYME, KEGG, and BioCyc, and in addition the UniProt, GenBank, NCBI Taxonomy, and CMR databases, and the Gene Ontology. Loader tools, written in the C and JAVA languages, parse and load these databases into a relational database schema. The loaders also apply a degree of semantic normalization to their respective source data, decreasing semantic heterogeneity. The schema supports the following bioinformatics datatypes: chemical compounds, biochemical reactions, metabolic pathways, proteins, genes, nucleic acid sequences, features on protein and nucleic-acid sequences, organisms, organism taxonomies, and controlled vocabularies. As an application example, we applied BioWarehouse to determine the fraction of biochemically characterized enzyme activities for which no sequences exist in the public sequence databases. The answer is that no sequence exists for 36% of enzyme activities for which EC numbers have been assigned. These gaps in sequence data significantly limit the accuracy of genome annotation and metabolic pathway prediction, and are a barrier for metabolic engineering. Complex queries of this type provide examples of the value of the data warehousing approach to bioinformatics research. BioWarehouse embodies significant progress on the database integration problem for bioinformatics.

Estimating the required logistical resources to support the development of a sustainable corn stover bioeconomy in the USA

DOE PAGES

Ebadian, Mahmood; Sokhansanj, Shahabaddine; Webb, Erin

2016-11-23

In this paper, the logistical resources required to develop a bioeconomy based on corn stover in the USA are quantified, including field equipment, storage sites, transportation and handling equipment, workforce, corn growers, and corn lands. These resources are essential to mobilize large quantities of corn stover from corn fields to biorefineries. The logistical resources are estimated over the lifetime of the biorefineries. Seventeen corn-growing states are considered for the logistical resource assessment. Over 6.8 billion gallons of cellulosic ethanol can be produced annually from 108 million dry tons of corn stover in these states. The maximum number of required fieldmore » equipment (i.e., choppers, balers, collectors, loaders, and tractors) is estimated to be 194 110 units with a total economic value of about 26 billion dollars. In addition, 40 780 trucks and flatbed trailers would be required to transport bales from corn fields and storage sites to biorefineries with a total economic value of 4.0 billion dollars. About 88 899 corn growers need to be contracted with an annual net income of over 2.1 billion dollars. About 1903 storage sites would be required to hold 53.1 million dry tons of inventory after the harvest season. These storage sites would take up about 35 320.2 acres and 4077 loaders with an economic value of 0.4 billion dollars would handle this inventory. The total required workforce to run the logistics operations is estimated to be 50 567. Furthermore, the magnitude of the estimated logistical resources demonstrates the economic and social significance of the corn stover bioeconomy in rural areas in the USA.« less

Estimating the required logistical resources to support the development of a sustainable corn stover bioeconomy in the USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ebadian, Mahmood; Sokhansanj, Shahabaddine; Webb, Erin

In this paper, the logistical resources required to develop a bioeconomy based on corn stover in the USA are quantified, including field equipment, storage sites, transportation and handling equipment, workforce, corn growers, and corn lands. These resources are essential to mobilize large quantities of corn stover from corn fields to biorefineries. The logistical resources are estimated over the lifetime of the biorefineries. Seventeen corn-growing states are considered for the logistical resource assessment. Over 6.8 billion gallons of cellulosic ethanol can be produced annually from 108 million dry tons of corn stover in these states. The maximum number of required fieldmore » equipment (i.e., choppers, balers, collectors, loaders, and tractors) is estimated to be 194 110 units with a total economic value of about 26 billion dollars. In addition, 40 780 trucks and flatbed trailers would be required to transport bales from corn fields and storage sites to biorefineries with a total economic value of 4.0 billion dollars. About 88 899 corn growers need to be contracted with an annual net income of over 2.1 billion dollars. About 1903 storage sites would be required to hold 53.1 million dry tons of inventory after the harvest season. These storage sites would take up about 35 320.2 acres and 4077 loaders with an economic value of 0.4 billion dollars would handle this inventory. The total required workforce to run the logistics operations is estimated to be 50 567. Furthermore, the magnitude of the estimated logistical resources demonstrates the economic and social significance of the corn stover bioeconomy in rural areas in the USA.« less

Rv0004 is a new essential member of the mycobacterial DNA replication machinery.

PubMed

Mann, Katherine M; Huang, Deborah L; Hooppaw, Anna J; Logsdon, Michelle M; Richardson, Kirill; Lee, Hark Joon; Kimmey, Jacqueline M; Aldridge, Bree B; Stallings, Christina L

2017-11-01

DNA replication is fundamental for life, yet a detailed understanding of bacterial DNA replication is limited outside the organisms Escherichia coli and Bacillus subtilis. Many bacteria, including mycobacteria, encode no identified homologs of helicase loaders or regulators of the initiator protein DnaA, despite these factors being essential for DNA replication in E. coli and B. subtilis. In this study we discover that a previously uncharacterized protein, Rv0004, from the human pathogen Mycobacterium tuberculosis is essential for bacterial viability and that depletion of Rv0004 leads to a block in cell cycle progression. Using a combination of genetic and biochemical approaches, we found that Rv0004 has a role in DNA replication, interacts with DNA and the replicative helicase DnaB, and affects DnaB-DnaA complex formation. We also identify a conserved domain in Rv0004 that is predicted to structurally resemble the N-terminal protein-protein interaction domain of DnaA. Mutation of a single conserved tryptophan within Rv0004's DnaA N-terminal-like domain leads to phenotypes similar to those observed upon Rv0004 depletion and can affect the association of Rv0004 with DnaB. In addition, using live cell imaging during depletion of Rv0004, we have uncovered a previously unappreciated role for DNA replication in coordinating mycobacterial cell division and cell size. Together, our data support that Rv0004 encodes a homolog of the recently identified DciA family of proteins found in most bacteria that lack the DnaC-DnaI helicase loaders in E. coli and B. subtilis. Therefore, the mechanisms of Rv0004 elucidated here likely apply to other DciA homologs and reveal insight into the diversity of bacterial strategies in even the most conserved biological processes.

Cytology of the minor-vein phloem in 320 species from the subclass Asteridae suggests a high diversity of phloem-loading modes†

PubMed Central

Batashev, Denis R.; Pakhomova, Marina V.; Razumovskaya, Anna V.; Voitsekhovskaja, Olga V.; Gamalei, Yuri V.

2013-01-01

The discovery of abundant plasmodesmata at the bundle sheath/phloem interface in Oleaceae (Gamalei, 1974) and Cucurbitaceae (Turgeon et al., 1975) raised the questions as to whether these plasmodesmata are functional in phloem loading and how widespread symplasmic loading would be. Analysis of over 800 dicot species allowed the definition of “open” and “closed” types of the minor vein phloem depending on the abundance of plasmodesmata between companion cells and bundle sheath (Gamalei, 1989, 1990). These types corresponded to potential symplasmic and apoplasmic phloem loaders, respectively; however, this definition covered a spectrum of diverse structures of phloem endings. Here, a review of detailed cytological analyses of minor veins in 320 species from the subclass Asteridae is presented, including data on companion cell types and their combinations which have not been reported previously. The percentage of Asteridae species with “open” minor vein cytology which also contain sieve-element-companion cell complexes with “closed” cytology, i.e., that show specialization for both symplasmic and apoplasmic phloem loading, was determined. Along with recent data confirming the dissimilar functional specialization of structurally different parts of minor vein phloem in the stachyose-translocating species Alonsoa meridionalis (Voitsekhovskaja et al., 2009), these findings suggest that apoplasmic loading is indispensable in a large group of species previously classified as putative symplasmic loaders. Altogether, this study provides formal classifications of companion cells and of minor veins, respectively, in 24 families of the Asteridae based on their structural features, opening the way to a close investigation of the relationship between structure and function in phloem loading. PMID:23970890

A 3 kbar hydrogen-compatible gas loader for Paris-Edinburgh presses

NASA Astrophysics Data System (ADS)

Klotz, S.; Philippe, J.; Bull, C. L.; Loveday, J. S.; Nelmes, R. J.

2013-03-01

We present a device which allows compressed gases to be loaded into large volume opposed anvils used for high pressure neutron scattering in the multi-10 GPa range. The gases are initially loaded into clamps which can then be inserted into VX-Paris-Edinburgh load frames. The system is compatible with all inert gases as well as hydrogen and permits loading pressures of up to 3 kbar for which most gases have densities close to that of the liquid at ambient pressure. The device should have applications for the study of simple molecular solids as well as for loading gases as pressure-transmitting media.

The Human Operator and System Effectiveness.

DTIC Science & Technology

1984-06-01

required in some decision process (e. g., component selection). 14 le NWC TP 6541 3. Be clearly stated in the final study report, with the rationale...BICYC LES t 5 - : BUSRSTO %* -.-’. ... % .% % . . J . % ... ~ ,4~ V’ .- *’ .-.-. , -LOADER T 1 = 1 + t 2 + LARGEST OF (t 3, t 4, t5) ,’ .t 2 t 3...34’,"t OPEN I UNLOAD " "I t DOORS PASSENGERSHI H" "" I PARK" "B. I AT t 5 t 4 BU SO OPERATE UNLOAD • . _ P LO A D ER BICYC LES -’, ",T 1 t I + L A R G

ATPase activity measurement of DNA replicative helicase from Bacillus stearothermophilus by malachite green method.

PubMed

Yang, Mu; Wang, Ganggang

2016-09-15

The DnaB helicase from Bacillus stearothermophilus (DnaBBst) was a model protein for studying the bacterial DNA replication. In this work, a non-radioactive method for measuring ATPase activity of DnaBBst helicase was described. The working parameters and conditions were optimized. Furthermore, this method was applied to investigate effects of DnaG primase, ssDNA and helicase loader protein (DnaI) on ATPase activity of DnaBBst. Our results showed this method was sensitive and efficient. Moreover, it is suitable for the investigation of functional interaction between DnaB and related factors. Copyright © 2016 Elsevier Inc. All rights reserved.

Construction of a robust, large-scale, collaborative database for raw data in computational chemistry: the Collaborative Chemistry Database Tool (CCDBT).

PubMed

Chen, Mingyang; Stott, Amanda C; Li, Shenggang; Dixon, David A

2012-04-01

A robust metadata database called the Collaborative Chemistry Database Tool (CCDBT) for massive amounts of computational chemistry raw data has been designed and implemented. It performs data synchronization and simultaneously extracts the metadata. Computational chemistry data in various formats from different computing sources, software packages, and users can be parsed into uniform metadata for storage in a MySQL database. Parsing is performed by a parsing pyramid, including parsers written for different levels of data types and sets created by the parser loader after loading parser engines and configurations. Copyright © 2011 Elsevier Inc. All rights reserved.

Investigation of the Finite Element Software Packages at KSC

NASA Technical Reports Server (NTRS)

Lu, Chu-Ho

1991-01-01

The useful and powerful features of NASTRAN and three real world problems for the testing of the capabilities of different NASTRAN versions are discussed. The test problems involve direct transient analysis, nonlinear analysis, and static analysis. The experiences in using graphics software packages are also discussed. It was found that MSC/XL can be more useful if it can be improved to generate picture files of the analysis results and to extend its capabilities to support finite element codes other than MSC/NASTRAN. It was found that the current version of SDRC/I-DEAS (version VI) may have bugs in the module 'Data Loader'.

Cost Benefit Analysis Modeling Tool for Electric vs. ICE Airport Ground Support Equipment – Development and Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

James Francfort; Kevin Morrow; Dimitri Hochard

2007-02-01

This report documents efforts to develop a computer tool for modeling the economic payback for comparative airport ground support equipment (GSE) that are propelled by either electric motors or gasoline and diesel engines. The types of GSE modeled are pushback tractors, baggage tractors, and belt loaders. The GSE modeling tool includes an emissions module that estimates the amount of tailpipe emissions saved by replacing internal combustion engine GSE with electric GSE. This report contains modeling assumptions, methodology, a user’s manual, and modeling results. The model was developed based on the operations of two airlines at four United States airports.

Simulation validation of the XV-15 tilt-rotor research aircraft

NASA Technical Reports Server (NTRS)

Ferguson, S. W.; Hanson, G. D.; Churchill, G. B.

1984-01-01

The results of a simulation validation program of the XV-15 tilt-rotor research aircraft are detailed, covering such simulation aspects as the mathematical model, visual system, motion system, cab aural system, cab control loader system, pilot perceptual fidelity, and generic tilt rotor applications. Simulation validation was performed for the hover, low-speed, and sideward flight modes, with consideration of the in-ground rotor effect. Several deficiencies of the mathematical model and the simulation systems were identified in the course of the simulation validation project, and some were corrected. It is noted that NASA's Vertical Motion Simulator used in the program is an excellent tool for tilt-rotor and rotorcraft design, development, and pilot training.

Total number of longwall faces drops below 50

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2009-02-15

For the first time since Coal Age began its annual Longwall Census the number of faces has dropped below 50. A total of five mines operate two longwall faces. CONSOL Energy remains the leader with 12 faces. Arch Coal operates five longwall mines; Robert E. Murray owns five longwall mines. West Virginia has 13 longwalls, followed by Pennsylvania (8), Utah (6) and Alabama (6). A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries, depth of cut, model of equipment used (shearer, haulage system, roof support, facemore » conveyor, stage loader, crusher, electrical controls and voltage to face). 2 tabs., 1 photo.« less

Design of 3D simulation engine for oilfield safety training

NASA Astrophysics Data System (ADS)

Li, Hua-Ming; Kang, Bao-Sheng

2015-03-01

Aiming at the demand for rapid custom development of 3D simulation system for oilfield safety training, this paper designs and implements a 3D simulation engine based on script-driven method, multi-layer structure, pre-defined entity objects and high-level tools such as scene editor, script editor, program loader. A scripting language been defined to control the system's progress, events and operating results. Training teacher can use this engine to edit 3D virtual scenes, set the properties of entity objects, define the logic script of task, and produce a 3D simulation training system without any skills of programming. Through expanding entity class, this engine can be quickly applied to other virtual training areas.

Integration of bio- and geoscience data with the ODM2 standards and software ecosystem for the CZOData and BiG CZ Data projects

NASA Astrophysics Data System (ADS)

Aufdenkampe, A. K.; Mayorga, E.; Horsburgh, J. S.; Lehnert, K. A.; Zaslavsky, I.

2015-12-01

We have developed a family of solutions to the challenges of integrating diverse data from of biological and geological (BiG) disciplines for Critical Zone (CZ) science. These standards and software solutions have been developed around the new Observations Data Model version 2.0 (ODM2, http://ODM2.org), which was designed as a profile of the Open Geospatial Consortium's (OGC) Observations and Measurements (O&M) standard. The ODM2 standards and software ecosystem has at it's core an information model that balances specificity with flexibility to powerfully and equally serve the needs of multiple dataset types, from multivariate sensor-generated time series to geochemical measurements of specimen hierarchies to multi-dimensional spectral data to biodiversity observations. ODM2 has been adopted as the information model guiding the next generation of cyberinfrastructure development for the Interdisciplinary Earth Data Alliance (http://www.iedadata.org/) and the CUAHSI Water Data Center (https://www.cuahsi.org/wdc). Here we present several components of the ODM2 standards and software ecosystem that were developed specifically to help CZ scientists and their data managers to share and manage data through the national Critical Zone Observatory data integration project (CZOData, http://criticalzone.org/national/data/) and the bio integration with geo for critical zone science data project (BiG CZ Data, http://bigcz.org/). These include the ODM2 Controlled Vocabulary system (http://vocabulary.odm2.org), the YAML Observation Data Archive & exchange (YODA) File Format (https://github.com/ODM2/YODA-File) and the BiG CZ Toolbox, which will combine easy-to-install ODM2 databases (https://github.com/ODM2/ODM2) with a variety of graphical software packages for data management such as ODMTools (https://github.com/ODM2/ODMToolsPython) and the ODM2 Streaming Data Loader (https://github.com/ODM2/ODM2StreamingDataLoader).

Analyses of requirements for computer control and data processing experiment subsystems. Volume 2: ATM experiment S-056 image data processing system software development

NASA Technical Reports Server (NTRS)

1972-01-01

The IDAPS (Image Data Processing System) is a user-oriented, computer-based, language and control system, which provides a framework or standard for implementing image data processing applications, simplifies set-up of image processing runs so that the system may be used without a working knowledge of computer programming or operation, streamlines operation of the image processing facility, and allows multiple applications to be run in sequence without operator interaction. The control system loads the operators, interprets the input, constructs the necessary parameters for each application, and cells the application. The overlay feature of the IBSYS loader (IBLDR) provides the means of running multiple operators which would otherwise overflow core storage.

FORTRAN Automated Code Evaluation System (faces) system documentation, version 2, mod 0. [error detection codes/user manuals (computer programs)

NASA Technical Reports Server (NTRS)

1975-01-01

A system is presented which processes FORTRAN based software systems to surface potential problems before they become execution malfunctions. The system complements the diagnostic capabilities of compilers, loaders, and execution monitors rather than duplicating these functions. Also, it emphasizes frequent sources of FORTRAN problems which require inordinate manual effort to identify. The principle value of the system is extracting small sections of unusual code from the bulk of normal sequences. Code structures likely to cause immediate or future problems are brought to the user's attention. These messages stimulate timely corrective action of solid errors and promote identification of 'tricky' code. Corrective action may require recoding or simply extending software documentation to explain the unusual technique.

Coal companies invest in more longwall capacity

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2006-02-15

This year's annual survey shows not much has changed since last year. The overall population stands at 47 mines operating 53 longwalls. CONSOL Energy remains the leading US longwall operator with 13 installations, followed by Arch Coal (5), Robert E. Murray (5) and Massey Energy (4). West Virginia remains the leading longwall mining state with 14 faces in 2005, followed by Pennsylvania (8), Alabama (7), Utah (7) and Colorado (5). A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries, depth of cut, model of equipment usedmore » (shearer, haulage system, roof support, face conveyor, stage loader, crusher, electrical controls and voltage to face). 1 photos., 2 tabs.« less

Combining virtual reality and multimedia techniques for effective maintenance training

NASA Astrophysics Data System (ADS)

McLin, David M.; Chung, James C.

1996-02-01

This paper describes a virtual reality (VR) system developed for use as part of an integrated, low-cost, stand-alone, multimedia trainer. The trainer is used to train National Guard personnel in maintenance and trouble-shooting tasks for the M1A1 Abrams tank, the M2A2 Bradley fighting vehicle and the TOW II missile system. The VR system features a modular, extensible, object-oriented design which consists of a training monitor component, a VR run time component, a model loader component, and a set of domain-specific object behaviors which mimic the behavior of objects encountered in the actual vehicles. The VR system is built from a combination of off-the-shelf commercial software and custom software developed at RTI.

Underground coal operators install several new longwall mining systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fiscor, S.

2008-02-15

Several new names appear in the annual US Longwall Census, but the population remains the same: 52 although the number of longwall mines dropped from 40 to 47. CONSOL Energy remains the leader with 12 faces. Robert E. Murray owns 8 longwall mines followed by Arch Coal with 5 and Foundation Coal with 3. West Virginia has 13 longwalls followed by 9 in Pennsylvania, 7 in Utah and 6 in Alabama. The article describes CONSOL Energy's operations. A detailed table gives for each longwall installation, the ownership, seam height, cutting height, panel width and length, overburden, number of gate entries,more » depth of cut, model of equipment used (shearer, haulage system, roof support, face conveyor, stage loader, crusher, electrical controls and voltage to face). 2 tabs.« less

New insights into cohesin loading.

PubMed

Litwin, Ireneusz; Wysocki, Robert

2018-02-01

Cohesin is a conserved, ring-shaped protein complex that encircles sister chromatids and ensures correct chromosome segregation during mitosis and meiosis. It also plays a crucial role in the regulation of gene expression, DNA condensation, and DNA repair through both non-homologous end joining and homologous recombination. Cohesins are spatiotemporally regulated by the Scc2-Scc4 complex which facilitates cohesin loading onto chromatin at specific chromosomal sites. Over the last few years, much attention has been paid to cohesin and cohesin loader as it became clear that even minor disruptions of these complexes may lead to developmental disorders and cancers. Here we summarize recent developments in the structure of Scc2-Scc4 complex, cohesin loading process, and mediators that determine the Scc2-Scc4 binding patterns to chromatin.

Lunar surface structural concepts and construction studies

NASA Technical Reports Server (NTRS)

Mikulas, Martin

1991-01-01

The topics are presented in viewgraph form and include the following: lunar surface structures construction research areas; lunar crane related disciplines; shortcomings of typical mobile crane in lunar base applications; candidate crane cable suspension systems; NIST six-cable suspension crane; numerical example of natural frequency; the incorporation of two new features for improved performance of the counter-balanced actively-controlled lunar crane; lunar crane pendulum mechanics; simulation results; 1/6 scale lunar crane testbed using GE robot for global manipulation; basic deployable truss approaches; bi-pantograph elevator platform; comparison of elevator platforms; perspective of bi-pantograph beam; bi-pantograph synchronously deployable tower/beam; lunar module off-loading concept; module off-loader concept packaged; starburst deployable precision reflector; 3-ring reflector deployment scheme; cross-section of packaged starburst reflector; and focal point and thickness packaging considerations.

Automatic computer subprogram selection from application program libraries

NASA Technical Reports Server (NTRS)

Drozdowski, J. M.

1972-01-01

The program ALTLIB (ALTernate LIBrary) which allows a user access to an alternate subprogram library with a minimum effort is discussed. The ALTLIB program selects subprograms from an alternate library file and merges them with the user's program load file. Only subprograms that are called for (directly or indirectly) by the user's programs and that are available on the alternate library file will be selected. ALTLIB eliminates the need for elaborate control-card manipulations to add subprograms from a subprogram file. ALTLIB returns to the user his binary file and the selected subprograms in correct order for a call to the loader. The user supplies the alternate library file. Subprogram requests which are not satisfied from the alternate library file will be satisfied at load time from the system library.

RecFOR Is Not Required for Pneumococcal Transformation but Together with XerS for Resolution of Chromosome Dimers Frequently Formed in the Process

PubMed Central

Johnston, Calum; Mortier-Barrière, Isabelle; Granadel, Chantal; Polard, Patrice; Martin, Bernard; Claverys, Jean-Pierre

2015-01-01

Homologous recombination (HR) is required for both genome maintenance and generation of diversity in eukaryotes and prokaryotes. This process initiates from single-stranded (ss) DNA and is driven by a universal recombinase, which promotes strand exchange between homologous sequences. The bacterial recombinase, RecA, is loaded onto ssDNA by recombinase loaders, RecBCD and RecFOR for genome maintenance. DprA was recently proposed as a third loader dedicated to genetic transformation. Here we assessed the role of RecFOR in transformation of the human pathogen Streptococcus pneumoniae. We firstly established that RecFOR proteins are not required for plasmid transformation, strongly suggesting that DprA ensures annealing of plasmid single-strands internalized in the process. We then observed no reduction in chromosomal transformation using a PCR fragment as donor, contrasting with the 10,000-fold drop in dprA - cells and demonstrating that RecFOR play no role in transformation. However, a ∼1.45-fold drop in transformation was observed with total chromosomal DNA in recFOR mutants. To account for this limited deficit, we hypothesized that transformation with chromosomal DNA stimulated unexpectedly high frequency (>30% of cells) formation of chromosome dimers as an intermediate in the generation of tandem duplications, and that RecFOR were crucial for dimer resolution. We validated this hypothesis, showing that the site-specific recombinase XerS was also crucial for dimer resolution. An even higher frequency of dimer formation (>80% of cells) was promoted by interspecies transformation with Streptococcus mitis chromosomal DNA, which contains numerous inversions compared to pneumococcal chromosome, each potentially promoting dimerization. In the absence of RecFOR and XerS, dimers persist, as confirmed by DAPI staining, and can limit the efficiency of transformation, since resulting in loss of transformant chromosome. These findings strengthen the view that different HR machineries exist for genome maintenance and transformation in pneumococci. These observations presumably apply to most naturally transformable species. PMID:25569614

AstroML: "better, faster, cheaper" towards state-of-the-art data mining and machine learning

NASA Astrophysics Data System (ADS)

Ivezic, Zeljko; Connolly, Andrew J.; Vanderplas, Jacob

2015-01-01

We present AstroML, a Python module for machine learning and data mining built on numpy, scipy, scikit-learn, matplotlib, and astropy, and distributed under an open license. AstroML contains a growing library of statistical and machine learning routines for analyzing astronomical data in Python, loaders for several open astronomical datasets (such as SDSS and other recent major surveys), and a large suite of examples of analyzing and visualizing astronomical datasets. AstroML is especially suitable for introducing undergraduate students to numerical research projects and for graduate students to rapidly undertake cutting-edge research. The long-term goal of astroML is to provide a community repository for fast Python implementations of common tools and routines used for statistical data analysis in astronomy and astrophysics (see http://www.astroml.org).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wickstrom, Gregory Lloyd; Gale, Jason Carl; Ma, Kwok Kee

The Sandia Secure Processor (SSP) is a new native Java processor that has been specifically designed for embedded applications. The SSP's design is a system composed of a core Java processor that directly executes Java bytecodes, on-chip intelligent IO modules, and a suite of software tools for simulation and compiling executable binary files. The SSP is unique in that it provides a way to control real-time IO modules for embedded applications. The system software for the SSP is a 'class loader' that takes Java .class files (created with your favorite Java compiler), links them together, and compiles a binary. Themore » complete SSP system provides very powerful functionality with very light hardware requirements with the potential to be used in a wide variety of small-system embedded applications. This paper gives a detail description of the Sandia Secure Processor and its unique features.« less

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing.

PubMed

Capriotti, Margherita; Kim, Hyungsuk E; Scalea, Francesco Lanza di; Kim, Hyonny

2017-06-04

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers.

Non-Destructive Inspection of Impact Damage in Composite Aircraft Panels by Ultrasonic Guided Waves and Statistical Processing

PubMed Central

Capriotti, Margherita; Kim, Hyungsuk E.; Lanza di Scalea, Francesco; Kim, Hyonny

2017-01-01

This paper discusses a non-destructive evaluation (NDE) technique for the detection of damage in composite aircraft structures following high energy wide area blunt impact (HEWABI) from ground service equipment (GSE), such as heavy cargo loaders and other heavy equipment. The test structures typically include skin, co-cured stringers, and C-frames that are bolt-connected onto the skin with shear ties. The inspection exploits the waveguide geometry of these structures by utilizing ultrasonic guided waves and a line scan approach. Both a contact prototype and a non-contact prototype were developed and tested on realistic test panels subjected to impact in the laboratory. The results are presented in terms of receiver operating characteristic curves that show excellent probability of detection with low false alarm rates for defects located in the panel skin and stringers. PMID:28772976

The accident analysis of mobile mine machinery in Indian opencast coal mines.

PubMed

Kumar, R; Ghosh, A K

2014-01-01

This paper presents the analysis of large mining machinery related accidents in Indian opencast coal mines. The trends of coal production, share of mining methods in production, machinery deployment in open cast mines, size and population of machinery, accidents due to machinery, types and causes of accidents have been analysed from the year 1995 to 2008. The scrutiny of accidents during this period reveals that most of the responsible factors are machine reversal, haul road design, human fault, operator's fault, machine fault, visibility and dump design. Considering the types of machines, namely, dumpers, excavators, dozers and loaders together the maximum number of fatal accidents has been caused by operator's faults and human faults jointly during the period from 1995 to 2008. The novel finding of this analysis is that large machines with state-of-the-art safety system did not reduce the fatal accidents in Indian opencast coal mines.

Microcomputer software development facilities

NASA Technical Reports Server (NTRS)

Gorman, J. S.; Mathiasen, C.

1980-01-01

A more efficient and cost effective method for developing microcomputer software is to utilize a host computer with high-speed peripheral support. Application programs such as cross assemblers, loaders, and simulators are implemented in the host computer for each of the microcomputers for which software development is a requirement. The host computer is configured to operate in a time share mode for multiusers. The remote terminals, printers, and down loading capabilities provided are based on user requirements. With this configuration a user, either local or remote, can use the host computer for microcomputer software development. Once the software is developed (through the code and modular debug stage) it can be downloaded to the development system or emulator in a test area where hardware/software integration functions can proceed. The microcomputer software program sources reside in the host computer and can be edited, assembled, loaded, and then downloaded as required until the software development project has been completed.

Simulator study of flight characteristics of several large, dissimilar, cargo transport airplanes during approach and landing

NASA Technical Reports Server (NTRS)

Grantham, W. D.; Smith, P. M.; Deal, P. L.; Neely, W. R., Jr.

1984-01-01

A six-degree-of-freedom, ground based simulator study is conducted to evaluate the low-speed flight characteristics of four dissimilar cargo transport airplanes. These characteristics are compared with those of a large, present-day (reference) transport configuration similar to the Lockheed C-5A airplane. The four very large transport concepts evaluated consist of single-fuselage, twin-fuselage, triple-fuselage, and span-loader configurations. The primary piloting task is the approach and landing operation. The results of his study indicate that all four concepts evaluated have unsatisfactory longitudinal and lateral directional low speed flight characteristics and that considerable stability and control augmentation would be required to improve these characteristics (handling qualities) to a satisfactory level. Through the use of rate command/attitude hold augmentation in the pitch and roll axes, and the use of several turn-coordination features, the handling qualities of all four large transports simulated are improved appreciably.

A PIECE OF THE SPACE SHUTTLE CHALLENGER WASHED ASHORE AT COCOA BEACH

NASA Technical Reports Server (NTRS)

1996-01-01

A Cocoa Beach front-end loader holds a large piece of debris from the Space Shuttle orbiter Challenger after it washed ashore in Cocoa Beach near the Coconuts on the Beach restaurant and bar. The piece, about 15 feet by 6 feet, is believed to be part of an elevon or rudder. It is one of the biggest pieces to wash ashore to date. A smaller piece was found several blocks south. NASA recovered thousands of pounds of debris from the Atlantic Ocean after the Jan. 28, 1986 accident which destroyed the Shuttle and claimed the lives of the seven crew members; about 50 percent of the orbiter remained in the ocean after search operations were suspended. Those remains are stored at Cape Canaveral Air Station, mostly in two Minutemen silos. The two newly recovered pieces will be brought by flatbed truck to KSC's Security Patrol Headquarters on Contractor Road for examination and temporary storage.

Analysis procedures and subjective flight results of a simulator validation and cue fidelity experiment

NASA Technical Reports Server (NTRS)

Carr, Peter C.; Mckissick, Burnell T.

1988-01-01

A joint experiment to investigate simulator validation and cue fidelity was conducted by the Dryden Flight Research Facility of NASA Ames Research Center (Ames-Dryden) and NASA Langley Research Center. The primary objective was to validate the use of a closed-loop pilot-vehicle mathematical model as an analytical tool for optimizing the tradeoff between simulator fidelity requirements and simulator cost. The validation process includes comparing model predictions with simulation and flight test results to evaluate various hypotheses for differences in motion and visual cues and information transfer. A group of five pilots flew air-to-air tracking maneuvers in the Langley differential maneuvering simulator and visual motion simulator and in an F-14 aircraft at Ames-Dryden. The simulators used motion and visual cueing devices including a g-seat, a helmet loader, wide field-of-view horizon, and a motion base platform.

Unusual planned complex suicide committed with a muzzle-loading pistol in combination with subsequent hanging.

PubMed

Ondruschka, Benjamin; Morgenthal, Sylvia; Dreβler, Jan; Bayer, Ronny

2016-11-01

In Germany, suicides by firearms are not very common in contrast to deaths by hanging and intoxications. The use of historical muzzle-loading firearms in the context of suicides is a rarity. Contact shots from muzzle loaders cause an unusual wound morphology with extensive soot soiling. We report the case of a 59-year-old man, who committed a planned complex suicide by shooting into his mouth with a replica percussion gun in combination with hanging. The gunshot injury showed strong explosive effects in the oral cavity with fractures of the facial bones and the skull associated with cerebral evisceration (so-called Krönlein shot). Due to the special constellation of the case with hanging immediately after the shot, external bleeding from the head injuries was only moderate. Therefore, the head injuries could be assessed and partially reconstructed already at the scene.

Technology transfer of operator-in-the-loop simulation

NASA Technical Reports Server (NTRS)

Yae, K. H.; Lin, H. C.; Lin, T. C.; Frisch, H. P.

1994-01-01

The technology developed for operator-in-the-loop simulation in space teleoperation has been applied to Caterpillar's backhoe, wheel loader, and off-highway truck. On an SGI workstation, the simulation integrates computer modeling of kinematics and dynamics, real-time computational and visualization, and an interface with the operator through the operator's console. The console is interfaced with the workstation through an IBM-PC in which the operator's commands were digitized and sent through an RS-232 serial port. The simulation gave visual feedback adequate for the operator in the loop, with the camera's field of vision projected on a large screen in multiple view windows. The view control can emulate either stationary or moving cameras. This simulator created an innovative engineering design environment by integrating computer software and hardware with the human operator's interactions. The backhoe simulation has been adopted by Caterpillar in building a virtual reality tool for backhoe design.

Excavating and loading equipment for peat mining

NASA Astrophysics Data System (ADS)

Mikhailov, A. V.; Zhigulskaya, A. I.; Yakonovskaya, T. B.

2017-10-01

Recently, the issues of sustainable development of Russian regions, related to ensuring energy security, are more urgent than ever. To achieve sustainable development, an integrated approach to the use of local natural resources is needed. Practically in all north regions of the Russian Federation, peat as a local natural resource is widespread, which has a practical application in the area of housing services. The paper presents the evaluation of technologies for open-pit peat mining, as well as analysis of technological equipment for peat production. Special attention is paid to a question of peat materials excavating and loading. The problem of equipment selection in a peat surface mine is complex. Many features, restrictions and criteria need to be considered. Use of low and ultra-low ground pressure excavators and low ground pressure front-end loaders with full-range tires to provide the necessary floatation in the peat bog environment is offered.

Cooperative working of bacterial chromosome replication proteins generated by a reconstituted protein expression system

PubMed Central

Fujiwara, Kei; Katayama, Tsutomu; Nomura, Shin-ichiro M.

2013-01-01

Replication of all living cells relies on the multirounds flow of the central dogma. Especially, expression of DNA replication proteins is a key step to circulate the processes of the central dogma. Here we achieved the entire sequential transcription–translation–replication process by autonomous expression of chromosomal DNA replication machineries from a reconstituted transcription–translation system (PURE system). We found that low temperature is essential to express a complex protein, DNA polymerase III, in a single tube using the PURE system. Addition of the 13 genes, encoding initiator, DNA helicase, helicase loader, RNA primase and DNA polymerase III to the PURE system gave rise to a DNA replication system by a coupling manner. An artificial genetic circuit demonstrated that the DNA produced as a result of the replication is able to provide genetic information for proteins, indicating the in vitro central dogma can sequentially undergo two rounds. PMID:23737447

Modelling foraging movements of diving predators: a theoretical study exploring the effect of heterogeneous landscapes on foraging efficiency

PubMed Central

Bartoń, Kamil A.; Scott, Beth E.; Travis, Justin M.J.

2014-01-01

Foraging in the marine environment presents particular challenges for air-breathing predators. Information about prey capture rates, the strategies that diving predators use to maximise prey encounter rates and foraging success are still largely unknown and difficult to observe. As well, with the growing awareness of potential climate change impacts and the increasing interest in the development of renewable sources it is unknown how the foraging activity of diving predators such as seabirds will respond to both the presence of underwater structures and the potential corresponding changes in prey distributions. Motivated by this issue we developed a theoretical model to gain general understanding of how the foraging efficiency of diving predators may vary according to landscape structure and foraging strategy. Our theoretical model highlights that animal movements, intervals between prey capture and foraging efficiency are likely to critically depend on the distribution of the prey resource and the size and distribution of introduced underwater structures. For multiple prey loaders, changes in prey distribution affected the searching time necessary to catch a set amount of prey which in turn affected the foraging efficiency. The spatial aggregation of prey around small devices (∼ 9 × 9 m) created a valuable habitat for a successful foraging activity resulting in shorter intervals between prey captures and higher foraging efficiency. The presence of large devices (∼ 24 × 24 m) however represented an obstacle for predator movement, thus increasing the intervals between prey captures. In contrast, for single prey loaders the introduction of spatial aggregation of the resources did not represent an advantage suggesting that their foraging efficiency is more strongly affected by other factors such as the timing to find the first prey item which was found to occur faster in the presence of large devices. The development of this theoretical model represents a useful starting point to understand the energetic reasons for a range of potential predator responses to spatial heterogeneity and environmental uncertainties in terms of search behaviour and predator–prey interactions. We highlight future directions that integrated empirical and modelling studies should take to improve our ability to predict how diving predators will be impacted by the deployment of manmade structures in the marine environment. PMID:25250211

A pneumatic device for rapid loading of DNA sequencing gels.

PubMed

Panussis, D A; Cook, M W; Rifkin, L L; Snider, J E; Strong, J T; McGrane, R M; Wilson, R K; Mardis, E R

1998-05-01

This work describes the design and construction of a device that facilitates the loading of DNA samples onto polyacrylamide gels for detection in the Perkin Elmer/Applied Biosystems (PE/ABI) 373 and 377 DNA sequencing instruments. The device is mounted onto the existing gel cassettes and makes the process of loading high-density gels less cumbersome while the associated time and errors are reduced. The principle of operation includes the simultaneous transfer of the entire batch of samples, in which a spring-loaded air cylinder generates positive pressure and flexible silica capillaries transfer the samples. A retractable capillary array carrier allows the delivery ends of the capillaries to be held up clear of the gel during loader attachment on the gel plates, while enabling their insertion in the gel wells once the device is securely mounted. Gel-loading devices capable of simultaneously transferring 72 samples onto the PE/ABI 373 and 377 are currently being used in our production sequencing groups while a 96-sample transfer prototype undergoes testing.

Edgar Buchanan: dentist and popular character actor in movies and television.

PubMed

Christen, A G; Christen, J A

2001-07-01

Edgar Buchanan, D.D.S., pursued a diverse mix of careers during his lifetime: as he practiced dentistry, he also worked as a popular film and television actor. Although he eventually relinquished a full-time dental practice for acting, he continued his commitment to clinical dentistry. Acting in 100 films and four television series across a 35-year span (1939-1975). He personified a scheming, yet well-meaning rustic who specialized in "cracker-barrel" philosophy. Typically, he was cast in classic western movies as a bewhiskered character actor. In several films he played a frontier dentist who was always portrayed in a sympathetic and authentic manner. His unique gravelly voice, subtle facial expressions, folksy mannerisms and portly build enabled Buchanan to step into a wide variety of character roles. His most memorable television role was in the classic situation comedy, "Petticoat Junction," (1963-1970), where he played Uncle Joe, a folksy, lovable, free-loader whose many entertaining schemes created chaos.

Integration of lyoplate based flow cytometry and computational analysis for standardized immunological biomarker discovery.

PubMed

Villanova, Federica; Di Meglio, Paola; Inokuma, Margaret; Aghaeepour, Nima; Perucha, Esperanza; Mollon, Jennifer; Nomura, Laurel; Hernandez-Fuentes, Maria; Cope, Andrew; Prevost, A Toby; Heck, Susanne; Maino, Vernon; Lord, Graham; Brinkman, Ryan R; Nestle, Frank O

2013-01-01

Discovery of novel immune biomarkers for monitoring of disease prognosis and response to therapy in immune-mediated inflammatory diseases is an important unmet clinical need. Here, we establish a novel framework for immunological biomarker discovery, comparing a conventional (liquid) flow cytometry platform (CFP) and a unique lyoplate-based flow cytometry platform (LFP) in combination with advanced computational data analysis. We demonstrate that LFP had higher sensitivity compared to CFP, with increased detection of cytokines (IFN-γ and IL-10) and activation markers (Foxp3 and CD25). Fluorescent intensity of cells stained with lyophilized antibodies was increased compared to cells stained with liquid antibodies. LFP, using a plate loader, allowed medium-throughput processing of samples with comparable intra- and inter-assay variability between platforms. Automated computational analysis identified novel immunophenotypes that were not detected with manual analysis. Our results establish a new flow cytometry platform for standardized and rapid immunological biomarker discovery with wide application to immune-mediated diseases.

Integration of Lyoplate Based Flow Cytometry and Computational Analysis for Standardized Immunological Biomarker Discovery

PubMed Central

Villanova, Federica; Di Meglio, Paola; Inokuma, Margaret; Aghaeepour, Nima; Perucha, Esperanza; Mollon, Jennifer; Nomura, Laurel; Hernandez-Fuentes, Maria; Cope, Andrew; Prevost, A. Toby; Heck, Susanne; Maino, Vernon; Lord, Graham; Brinkman, Ryan R.; Nestle, Frank O.

2013-01-01

Discovery of novel immune biomarkers for monitoring of disease prognosis and response to therapy in immune-mediated inflammatory diseases is an important unmet clinical need. Here, we establish a novel framework for immunological biomarker discovery, comparing a conventional (liquid) flow cytometry platform (CFP) and a unique lyoplate-based flow cytometry platform (LFP) in combination with advanced computational data analysis. We demonstrate that LFP had higher sensitivity compared to CFP, with increased detection of cytokines (IFN-γ and IL-10) and activation markers (Foxp3 and CD25). Fluorescent intensity of cells stained with lyophilized antibodies was increased compared to cells stained with liquid antibodies. LFP, using a plate loader, allowed medium-throughput processing of samples with comparable intra- and inter-assay variability between platforms. Automated computational analysis identified novel immunophenotypes that were not detected with manual analysis. Our results establish a new flow cytometry platform for standardized and rapid immunological biomarker discovery with wide application to immune-mediated diseases. PMID:23843942

Single-molecule visualization of fast polymerase turnover in the bacterial replisome

PubMed Central

Lewis, Jacob S; Spenkelink, Lisanne M; Jergic, Slobodan; Wood, Elizabeth A; Monachino, Enrico; Horan, Nicholas P; Duderstadt, Karl E; Cox, Michael M; Robinson, Andrew; Dixon, Nicholas E; van Oijen, Antoine M

2017-01-01

The Escherichia coli DNA replication machinery has been used as a road map to uncover design rules that enable DNA duplication with high efficiency and fidelity. Although the enzymatic activities of the replicative DNA Pol III are well understood, its dynamics within the replisome are not. Here, we test the accepted view that the Pol III holoenzyme remains stably associated within the replisome. We use in vitro single-molecule assays with fluorescently labeled polymerases to demonstrate that the Pol III* complex (holoenzyme lacking the β2 sliding clamp), is rapidly exchanged during processive DNA replication. Nevertheless, the replisome is highly resistant to dilution in the absence of Pol III* in solution. We further show similar exchange in live cells containing labeled clamp loader and polymerase. These observations suggest a concentration-dependent exchange mechanism providing a balance between stability and plasticity, facilitating replacement of replisomal components dependent on their availability in the environment. DOI: http://dx.doi.org/10.7554/eLife.23932.001 PMID:28432790

Intelligent Scheduling for Underground Mobile Mining Equipment.

PubMed

Song, Zhen; Schunnesson, Håkan; Rinne, Mikael; Sturgul, John

2015-01-01

Many studies have been carried out and many commercial software applications have been developed to improve the performances of surface mining operations, especially for the loader-trucks cycle of surface mining. However, there have been quite few studies aiming to improve the mining process of underground mines. In underground mines, mobile mining equipment is mostly scheduled instinctively, without theoretical support for these decisions. Furthermore, in case of unexpected events, it is hard for miners to rapidly find solutions to reschedule and to adapt the changes. This investigation first introduces the motivation, the technical background, and then the objective of the study. A decision support instrument (i.e. schedule optimizer for mobile mining equipment) is proposed and described to address this issue. The method and related algorithms which are used in this instrument are presented and discussed. The proposed method was tested by using a real case of Kittilä mine located in Finland. The result suggests that the proposed method can considerably improve the working efficiency and reduce the working time of the underground mine.

One-step synthesis of 3D sulfur/nitrogen dual-doped graphene supported nano silicon as anode for Li-ion batteries

NASA Astrophysics Data System (ADS)

Li, Ruihong; Li, Junli; Qi, Kaiyu; Ge, Xin; Zhang, Qiwei; Zhang, Bangwen

2018-03-01

Silicon is one of the most promising candidates for next-generation anode of Lithium-ion batteries. However, poor electrical conductivity and large volume change during alloying/dealloying hinder its practical use. Here we reported a three-dimensional (3D) nitrogen and sulfur codoped graphene supported silicon nanoparticles composite (SN-G/Si) through one-step hydrothermal self-assembly. The obtained SN-G/Si was investigated in term of instrumental characterizations and electrochemical properties. The results show that SN-G/Si as a freestanding anode in LIBs delivers a reversible capacity of 2020 mAh g-1 after 100 cycles with coulombic efficiency of nearly 97%. The excellent electrochemical performance is associated with the unique structure and the synergistic effect of SN-G/Si, in which SN-G provides volume buffer for nano Si as the flexible loader, short paths/fast channels for electron/Li ion transport as porous skeleton, and low charge-transfer resistance.

AstroML: Python-powered Machine Learning for Astronomy

NASA Astrophysics Data System (ADS)

Vander Plas, Jake; Connolly, A. J.; Ivezic, Z.

2014-01-01

As astronomical data sets grow in size and complexity, automated machine learning and data mining methods are becoming an increasingly fundamental component of research in the field. The astroML project (http://astroML.org) provides a common repository for practical examples of the data mining and machine learning tools used and developed by astronomical researchers, written in Python. The astroML module contains a host of general-purpose data analysis and machine learning routines, loaders for openly-available astronomical datasets, and fast implementations of specific computational methods often used in astronomy and astrophysics. The associated website features hundreds of examples of these routines being used for analysis of real astronomical datasets, while the associated textbook provides a curriculum resource for graduate-level courses focusing on practical statistics, machine learning, and data mining approaches within Astronomical research. This poster will highlight several of the more powerful and unique examples of analysis performed with astroML, all of which can be reproduced in their entirety on any computer with the proper packages installed.

Structure of the active form of human origin recognition complex and its ATPase motor module

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tocilj, Ante; On, Kin Fan; Yuan, Zuanning

Binding of the Origin Recognition Complex (ORC) to origins of replication marks the first step in the initiation of replication of the genome in all eukaryotic cells. Here, we report the structure of the active form of human ORC determined by X-ray crystallography and cryo-electron microscopy. The complex is composed of an ORC1/4/5 motor module lobe in an organization reminiscent of the DNA polymerase clamp loader complexes. A second lobe contains the ORC2/3 subunits. The complex is organized as a double-layered shallow corkscrew, with the AAA+ and AAA+-like domains forming one layer, and the winged-helix domains (WHDs) forming a topmore » layer. CDC6 fits easily between ORC1 and ORC2, completing the ring and the DNA-binding channel, forming an additional ATP hydrolysis site. Analysis of the ATPase activity of the complex provides a basis for understanding ORC activity as well as molecular defects observed in Meier-Gorlin Syndrome mutations.« less

In the line of fire--21st-century approach to an ancient war injury.

PubMed

Frank, Matthias; Rademacher, Grit; Schmucker, Uli; David, Stephan; Ekkernkamp, Axel

2009-03-01

Authentic black-powder muzzle-loader weapons or replicas are used today primarily for re-enactments of historic battles. A lay actor playing the role of a Prussian infantryman sustained life-threatening gunshot injuries during a recent re-enactment of a historic battle of the Sixth Coalition. As only blank historic muzzle-loading weaponry was used, the origin of the missile causing the wounding was initially unclear. Further investigation revealed a ramrod that had been propelled out of the barrel of another gunner's smooth-bore gun as cause of injury. The ramrod was hurled on a trajectory of more than 20 m, breaking the victim's shouldered barrel and hitting the victim resulting in severe abdominal, thoracic, and upper limb injuries. The critical incidents while handling muzzle-loading weaponry leading to premature discharge are elucidated. Furthermore, this report demonstrates how actual diagnostics and subsequent surgical treatment enabled this infantryman to survive an injury to which his comrades-in-arms would have succumbed 200 years ago.

Climatic interpretation of tree-ring methoxyl d2H time-series from a central alpine larch forest

NASA Astrophysics Data System (ADS)

Riechelmann, Dana F. C.; Greule, Markus; Siegwolf, Rolf T. W.; Esper, Jan; Keppler, Frank

2017-04-01

We measured stable hydrogen isotope ratios of lignin methoxyl groups (d2HLM) in high elevation larch trees (Larix decidua Mill.) from the Simplon Valley in southern Switzerland. Thirty-seven larch trees were sampled and five individuals analysed for their d2HLM values at annual (1971-2009) and pentadal resolution (1746-2009). Testing the climate response of the d2HLM series, the annually resolved series show a positive correlation of r = 0.60 with June/July precipitation and weaker but negative correlation with June/July temperature. In addition, a negative correlation with June-August d2H in precipitation of the nearby GNIP station in Locarno is observed. The pentadally resolved d2HLM series show no significant correlation to climate parameters. The positive correlation of the annually resolved data to summer precipitation is uncommon to d2H measurements from tree-rings (Feakins et al., 2013; Helle and Schleser, 2004; McCarroll and Loader, 2004; Mischel et al., 2015; White et al., 1994). However, we explain the positive association with warm season hydroclimate as follows: methoxyl groups of lignin are directly formed from tissues in the xylem water. More precipitation during June and July, which are on average relatively dry month, results in higher d2H values of the xylem water and therefore, higher d2H value in the lignin methoxyl groups. Therefore, we suggest that d2HLM values of high elevation larch trees might likely serve as a summer precipitation proxy. References: Feakins, S.J., Ellsworth, P.V., Sternberg, L.d.S.L., 2013. Lignin methoxyl hydrogen isotope rations in a coastal ecosystem. Geochimica et Cosmochimica Acta, 121: 54-66. Helle, G., Schleser, G.H., 2004. Interpreting Climate Proxies from Tree-rings. In: Fischer, H., Floeser, G., Kumke, T., Lohmann, G., Miller, H., Negendank, J.F.W., et al., editors. The Climate in Historical Times. Springer Berlin Heidelberg, pp. 129-148. McCarroll, D., Loader, N.J., 2004. Stable isotopes in tree rings. Quaternary Science Reviews, 23: 771-801. Mischel, M., Esper, J., Keppler, F., Greule, M., Werner, W., 2015. d2H, d13C and d18O from whole wood, a-cellulose and lignin methoxyl groups in Pinus sylvestris: a multi-parameter approach. Isotopes in Environmental and Health Studies, 1-16. White, J.W.C., Lawrence, J.R., Broecker, W.S., 1994. Modeling and interpreting D/H ratios in tree rings: A test case of white pine in the northeastern United States. Geochimica et Cosmochimica Acta, 58: 851-862.

ADAPTATION OF CRACK GROWTH DETECTION TECHNIQUES TO US MATERIAL TEST REACTORS

DOE Office of Scientific and Technical Information (OSTI.GOV)

A. Joseph Palmer; Sebastien P. Teysseyre; Kurt L. Davis

2015-04-01

A key component in evaluating the ability of Light Water Reactors to operate beyond 60 years is characterizing the degradation of materials exposed to radiation and various water chemistries. Of particular concern is the response of reactor materials to Irradiation Assisted Stress Corrosion Cracking (IASCC). Some test reactors outside the United States, such as the Halden Boiling Water Reactor (HBWR), have developed techniques to measure crack growth propagation during irradiation. The basic approach is to use a custom-designed compact loading mechanism to stress the specimen during irradiation, while the crack in the specimen is monitored in-situ using the Direct Currentmore » Potential Drop (DCPD) method. In 2012 the US Department of Energy commissioned the Idaho National Laboratory and the MIT Nuclear Reactor Laboratory (MIT NRL) to take the basic concepts developed at the HBWR and adapt them to a test rig capable of conducting in-pile IASCC tests in US Material Test Reactors. The first two and half years of the project consisted of designing and testing the loader mechanism, testing individual components of the in-pile rig and electronic support equipment, and autoclave testing of the rig design prior to insertion in the MIT Reactor. The load was applied to the specimen by means of a scissor like mechanism, actuated by a miniature metal bellows driven by pneumatic pressure and sized to fit within the small in-core irradiation volume. In addition to the loader design, technical challenges included developing robust connections to the specimen for the applied current and voltage measurements, appropriate ceramic insulating materials that can endure the LWR environment, dealing with the high electromagnetic noise environment of a reactor core at full power, and accommodating material property changes in the specimen, due primarily to fast neutron damage, which change the specimen resistance without additional crack growth. The project culminated with an in-pile demonstration at the MIT Reactor. The test rig and associated support equipment were used to apply loads to a representative Compact Tensile specimen during one MITR operating cycle, while measuring crack growth using the DCPD method. Although the test period was short (approximately 70 days), and the accumulated neutron dose relatively small, successful operation of the test rig was demonstrated. The specimen was cycled more than 8000 times (more than would be typical for a long term IASCC test), which was sufficient to propagate a crack of over 2 mm.« less

Telerobotic Excavator Designed to Compete in NASA's Lunabotics Mining Competition

NASA Technical Reports Server (NTRS)

Nash, Rodney; Santin, Cara; Yousef, Ahmed; Nguyen, Thien; Helferty, John; Pillapakkam, Shriram

2011-01-01

The second annual NASA Lunabotics Mining competition is to be held in May 23-28, 2011. The goal of the competition is for teams of university level students to design, build, test and compete with a fully integrated lunar excavator on a simulated lunar surface. Our team, named Lunar Solutions I, will be representing Temple University's College of Engineering in the competition. The team's main goal was to build a robot which is able to compete with other teams, and ultimately win the competition. The main challenge of the competition was to build a wireless robot that can excavate and collect a minimum of 10 kilograms of the regolith material within 15 minutes. The robot must also be designed to operate in conditions similar to those found on the lunar surface. The design of the lunar excavator is constrained by a set of requirements determined by NASA and detailed in the competition's rulebook. The excavator must have the ability to communicate with the "main base" wirelessly, and over a Wi-Fi network. Human operators are located at a remote site approximately 60 meters away from the simulated lunar surface upon which the robot must excavate the lunar regolith surface. During the competition, the robot will operate in a separate area from the control room in an area referred to as the "Lunarena." From the control room, the operators will have to control the robot using visual feedback from cameras placed both within the arena and on the robot. Using this visual feedback the human operators control the robots movement using both keyboard and joystick commands. In order to place in the competition, a minimum of 10 kg of regolith material has to be excavated, collected, and dumped into a specific location. For that reason, the robot must be provided with an effective and powerful excavation system. Our excavator uses tracks for the drive system. After performing extensive research and trade studies, we concluded that tracks would be the most effective method for transporting the excavator. When designing the excavation system, we analyzed several design options from the previous year's competition. We decided to use a front loader to collect the material, rather than a conveyer belt system or auger. Many of the designs from last year's competition used a conveyer belt mechanism to mine regolith and dump it into a temporary storage bin place on the robot. Using the front end loader approach allowed us to combine the scooping system and storage unit, which meant that the excavation system required less space.

Fall from equipment injuries in U.S. mining: identification of specific research areas for future investigation.

PubMed

Moore, Susan M; Porter, William L; Dempsey, Patrick G

2009-01-01

The objective of this study was to evaluate the circumstances leading to fall from equipment injuries in the mining industry. The 2006 and 2007 Mine Safety and Health Administration annual injury databases were utilized for this study whereby the injury narrative, nature of injury, body part injured, mine type, age at injury, and days lost were evaluated for each injury. The majority of injuries occurred at surface mining facilities (approximately 60%) with fractures and sprains/strains being the most common injuries occurring to the major joints of the body. Nearly 50% of injuries occurred during ingress/egress, predominantely during egress, and approximately 25% of injuries occurred during maintenance tasks. The majority of injuries occurred in relation to large trucks, wheel loaders, dozers, and conveyors/belts. The severity of injury was independent of age and the median days lost was seven days; however, there was a large range in severity. From the data obtained in this study, several different research areas have been identified for future work, which include balance and stability control when descending ladders and equipment design for maintenance tasks.

Drosophila model of Meier-Gorlin syndrome based on the mutation in a conserved C-Terminal domain of Orc6.

PubMed

Balasov, Maxim; Akhmetova, Katarina; Chesnokov, Igor

2015-11-01

Meier-Gorlin syndrome (MGS) is an autosomal recessive disorder characterized by microtia, primordial dwarfism, small ears, and skeletal abnormalities. Patients with MGS often carry mutations in the genes encoding the components of the pre-replicative complex such as Origin Recognition Complex (ORC) subunits Orc1, Orc4, Orc6, and helicase loaders Cdt1 and Cdc6. Orc6 is an important component of ORC and has functions in both DNA replication and cytokinesis. Mutation in conserved C-terminal motif of Orc6 associated with MGS impedes the interaction of Orc6 with core ORC. In order to study the effects of MGS mutation in an animal model system we introduced MGS mutation in Orc6 and established Drosophila model of MGS. Mutant flies die at third instar larval stage with abnormal chromosomes and DNA replication defects. The lethality can be rescued by elevated expression of mutant Orc6 protein. Rescued MGS flies are unable to fly and display multiple planar cell polarity defects. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

A novel automotive headlight system based on digital micro-mirror devices and diffractive optical elements

NASA Astrophysics Data System (ADS)

Su, Ping; Song, Yuming; Ma, Jianshe

2018-01-01

The DMD (Digital Micro-mirror Device) has the advantages of high refresh rate and high diffraction efficiency, and these make it become an ideal loader of multiple modes illumination. DOEs (Diffractive Optical Element) have the advantages of high degree of freedom, light weight, easy to copy, low cost etc., and can be used to reduce the weight, complexity, cost of optical system. A novel automotive headlamp system using DMD as the light distribution element and a DOE as the light field modulation device is proposed in this paper. The pure phase DOE is obtained by the GS algorithm using Rayleigh-Sommerfeld diffraction integral model. Based on the standard automotive headlamp light intensity distribution in the target plane, the amplitude distribution of DMD is obtained by numerical simulation, and the grayscale diagram loaded on the DMD can be obtained accordingly. Finally, according to simulation result, the light intensity distribution in the target plane is proportional to the national standard, hence verifies the validity of the novel system. The novel illumination system proposed in this paper provides a reliable hardware platform for the intelligent headlamps.

Exposure to TCDD from base perimeter application of Agent Orange in Vietnam.

PubMed

Ross, John H; Hewitt, Andrew; Armitage, James; Solomon, Keith; Watkins, Deborah K; Ginevan, Michael E

2015-04-01

Using recognized methods routinely employed by pesticide regulatory agencies, the exposures of military personnel that were mixer/loader/applicators (M/L/A) of Agent Orange (AO) for perimeter foliage at bases during the Vietnam War were estimated. From the fraction of TCDD in AO, absorbed dosage of the manufacturing contaminant was estimated. Dermal exposure estimated from spray drift to residents of the bases was calculated using internationally recognized software that accounted for proximity, foliar density of application site, droplet size and wind speed among other factors, and produced estimates of deposition. Those that directly handled AO generally had much higher exposures than those further from the areas of use. The differences in exposure potential varied by M/L/A activity, but were typically orders of magnitude greater than bystanders. However, even the most-exposed M/L/A involved in perimeter application had lifetime exposures comparable to persons living in the U.S. at the time, i.e., ~1.3 to 5 pg TCDD/kg bodyweight. Copyright © 2014 Elsevier B.V. All rights reserved.

Intelligent Scheduling for Underground Mobile Mining Equipment

PubMed Central

Song, Zhen; Schunnesson, Håkan; Rinne, Mikael; Sturgul, John

2015-01-01

Many studies have been carried out and many commercial software applications have been developed to improve the performances of surface mining operations, especially for the loader-trucks cycle of surface mining. However, there have been quite few studies aiming to improve the mining process of underground mines. In underground mines, mobile mining equipment is mostly scheduled instinctively, without theoretical support for these decisions. Furthermore, in case of unexpected events, it is hard for miners to rapidly find solutions to reschedule and to adapt the changes. This investigation first introduces the motivation, the technical background, and then the objective of the study. A decision support instrument (i.e. schedule optimizer for mobile mining equipment) is proposed and described to address this issue. The method and related algorithms which are used in this instrument are presented and discussed. The proposed method was tested by using a real case of Kittilä mine located in Finland. The result suggests that the proposed method can considerably improve the working efficiency and reduce the working time of the underground mine. PMID:26098934

An optimized procedure for obtaining DNA from fired and unfired ammunition.

PubMed

Montpetit, Shawn; O'Donnell, Patrick

2015-07-01

Gun crimes are a significant problem facing law enforcement agencies. Traditional forensic examination of firearms involves comparisons of markings imparted to bullets and cartridge casings during the firing process. DNA testing of casings and cartridges may not be routinely done in crime laboratories due a variety of factors including the typically low amounts of DNA recovered. The San Diego Police Department (SDPD) Crime Laboratory conducted a study to optimize the collection and profiling of DNA from fired and unfired ammunition. The method was optimized to where interpretable DNA results were obtained for 26.1% of the total number of forensic casework evidence samples, and provided some insights into the level of secondary transfer that might be expected from this type of evidence. Briefly detailed are the results from the experimental study and the forensic casework analysis using the optimized process. Mixtures (samples having more DNA types than the loader's known genotype detected or visible at any marker) were obtained in 39.8% of research samples and the likely source of DNA mixtures is discussed. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Structure of the active form of human origin recognition complex and its ATPase motor module

PubMed Central

Tocilj, Ante; On, Kin Fan; Yuan, Zuanning; Sun, Jingchuan; Elkayam, Elad; Li, Huilin; Stillman, Bruce; Joshua-Tor, Leemor

2017-01-01

Binding of the Origin Recognition Complex (ORC) to origins of replication marks the first step in the initiation of replication of the genome in all eukaryotic cells. Here, we report the structure of the active form of human ORC determined by X-ray crystallography and cryo-electron microscopy. The complex is composed of an ORC1/4/5 motor module lobe in an organization reminiscent of the DNA polymerase clamp loader complexes. A second lobe contains the ORC2/3 subunits. The complex is organized as a double-layered shallow corkscrew, with the AAA+ and AAA+-like domains forming one layer, and the winged-helix domains (WHDs) forming a top layer. CDC6 fits easily between ORC1 and ORC2, completing the ring and the DNA-binding channel, forming an additional ATP hydrolysis site. Analysis of the ATPase activity of the complex provides a basis for understanding ORC activity as well as molecular defects observed in Meier-Gorlin Syndrome mutations. DOI: http://dx.doi.org/10.7554/eLife.20818.001 PMID:28112645

A PIECE OF THE SPACE SHUTTLE CHALLENGER WASHED ASHORE AT COCOA BEACH

NASA Technical Reports Server (NTRS)

1996-01-01

News media representatives and other onlookers get a close-up view of the piece of Space Shuttle orbiter Challenger debris which washed ashore in Cocoa Beach near the Coconuts on the Beach restaurant and bar. A Cocoa Beach front-end loader picks up the debris which will be carried by flatbed truck to Kennedy Space Center. The piece, about 15 feet by 6 feet, is believed to be part of an elevon or rudder. It is one of the biggest pieces to wash ashore to date. A smaller piece also was found Tuesday several blocks south. NASA recovered thousands of pounds of debris from the Atlantic Ocean after the Jan. 28, 1986 accident which destroyed the Shuttle and claimed the lives of the seven crew members; about 50 percent of the orbiter remained in the ocean after search operations were suspended. Those remains are stored at Cape Canaveral Air Station, mostly in two Minutemen silos. The two newly recovered pieces will be brought to KSC's Security Patrol Headquarters on Contractor Road for examination and temporary storage.

A PIECE OF THE SPACE SHUTTLE CHALLENGER WASHED ASHORE AT COCOA BEACH

NASA Technical Reports Server (NTRS)

1996-01-01

A Cocoa Beach front-end loader holds a large piece of debris from the Space Shuttle orbiter Challenger after it washed ashore in Cocoa Beach near the Coconuts on the Beach restaurant and bar. Overseeing the recovery and protection of the piece is KSC criminal investigator Jan Seinkner, facing camera at center, of EG&G Florida Inc., base operations contractor. The piece, about 15 feet by 6 feet, is believed to be part of an elevon or rudder. It is one of the biggest pieces to wash ashore to date. A smaller piece was found several blocks south. NASA recovered thousands of pounds of debris from the Atlantic Ocean after the Jan. 28, 1986 accident which destroyed the Shuttle and claimed the lives of the seven crew members; about 50 percent of the orbiter remained in the ocean after search operations were suspended. Those remains are stored at Cape Canaveral Air Station, mostly in two Minutemen silos. The two newly recovered pieces will be brought to KSC's Security Patrol Headquarters on Contractor Road for examination and temporary storage.

WEST-3 wind turbine simulator development

NASA Technical Reports Server (NTRS)

Hoffman, J. A.; Sridhar, S.

1985-01-01

The software developed for WEST-3, a new, all digital, and fully programmable wind turbine simulator is given. The process of wind turbine simulation on WEST-3 is described in detail. The major steps are, the processing of the mathematical models, the preparation of the constant data, and the use of system software generated executable code for running on WEST-3. The mechanics of reformulation, normalization, and scaling of the mathematical models is discussed in detail, in particulr, the significance of reformulation which leads to accurate simulations. Descriptions for the preprocessor computer programs which are used to prepare the constant data needed in the simulation are given. These programs, in addition to scaling and normalizing all the constants, relieve the user from having to generate a large number of constants used in the simulation. Also given are brief descriptions of the components of the WEST-3 system software: Translator, Assembler, Linker, and Loader. Also included are: details of the aeroelastic rotor analysis, which is the center of a wind turbine simulation model, analysis of the gimbal subsystem; and listings of the variables, constants, and equations used in the simulation.

NOTE: Monte Carlo evaluation of kerma in an HDR brachytherapy bunker

NASA Astrophysics Data System (ADS)

Pérez-Calatayud, J.; Granero, D.; Ballester, F.; Casal, E.; Crispin, V.; Puchades, V.; León, A.; Verdú, G.

2004-12-01

In recent years, the use of high dose rate (HDR) after-loader machines has greatly increased due to the shift from traditional Cs-137/Ir-192 low dose rate (LDR) to HDR brachytherapy. The method used to calculate the required concrete and, where appropriate, lead shielding in the door is based on analytical methods provided by documents published by the ICRP, the IAEA and the NCRP. The purpose of this study is to perform a more realistic kerma evaluation at the entrance maze door of an HDR bunker using the Monte Carlo code GEANT4. The Monte Carlo results were validated experimentally. The spectrum at the maze entrance door, obtained with Monte Carlo, has an average energy of about 110 keV, maintaining a similar value along the length of the maze. The comparison of results from the aforementioned values with the Monte Carlo ones shows that results obtained using the albedo coefficient from the ICRP document more closely match those given by the Monte Carlo method, although the maximum value given by MC calculations is 30% greater.

Independent mechanisms recruit the cohesin loader protein NIPBL to sites of DNA damage.

PubMed

Bot, Christopher; Pfeiffer, Annika; Giordano, Fosco; Manjeera, Dharani E; Dantuma, Nico P; Ström, Lena

2017-03-15

NIPBL is required to load the cohesin complex on to DNA. While the canonical role of cohesin is to couple replicated sister chromatids together until the onset of mitosis, it also promotes tolerance to DNA damage. Here, we show that NIPBL is recruited to DNA damage throughout the cell cycle via independent mechanisms, influenced by type of damage. First, the heterochromatin protein HP1γ (also known as CBX3) recruits NIPBL to DNA double-strand breaks (DSBs) through the corresponding HP1-binding motif within the N-terminus. By contrast, the C-terminal HEAT repeat domain is unable to recruit NIPBL to DSBs but independently targets NIPBL to laser microirradiation-induced DNA damage. Each mechanism is dependent on the RNF8 and RNF168 ubiquitylation pathway, while the recruitment of the HEAT repeat domain requires further ATM or ATR activity. Thus, NIPBL has evolved a sophisticated response to damaged DNA that is influenced by the form of damage, suggesting a highly dynamic role for NIPBL in maintaining genomic stability. © 2017. Published by The Company of Biologists Ltd.

Drag Reduction and Performance Improvement of Hydraulic Torque Converters with Multiple Biological Characteristics.

PubMed

Chunbao, Liu; Li, Li; Yulong, Lei; Changsuo, Liu; Yubo, Zhang

2016-01-01

Fish-like, dolphin-like, and bionic nonsmooth surfaces were employed in a hydraulic torque converter to achieve drag reduction and performance improvement, which were aimed at reducing profile loss, impacting loss and friction loss, respectively. YJSW335, a twin turbine torque converter, was bionically designed delicately. The biological characteristics consisted of fish-like blades in all four wheels, dolphin-like structure in the first turbine and the stator, and nonsmooth surfaces in the pump. The prediction performance of bionic YJSW335, obtained by computational fluid dynamics simulation, was improved compared with that of the original model, and then it could be proved that drag reduction had been achieved. The mechanism accounting for drag reduction of three factors was also investigated. After bionic design, the torque ratio and the highest efficiencies of YJSW335 were both advanced, which were very difficult to achieve through traditional design method. Moreover, the highest efficiency of the low speed area and high speed area is 85.65% and 86.32%, respectively. By economic matching analysis of the original and bionic powertrains, the latter can significantly reduce the fuel consumption and improve the operating economy of the loader.

Machine-related injuries in the US mining industry and priorities for safety research.

PubMed

Ruff, Todd; Coleman, Patrick; Martini, Laura

2011-03-01

Researchers at the National Institute for Occupational Safety and Health studied mining accidents that involved a worker entangled in, struck by, or in contact with machinery or equipment in motion. The motivation for this study came from the large number of severe accidents, i.e. accidents resulting in a fatality or permanent disability, that are occurring despite available interventions. Accident descriptions were taken from an accident database maintained by the United States Department of Labor, Mine Safety and Health Administration, and 562 accidents that occurred during 2000-2007 fit the search criteria. Machine-related accidents accounted for 41% of all severe accidents in the mining industry during this period. Machinery most often involved in these accidents included conveyors, rock bolting machines, milling machines and haulage equipment such as trucks and loaders. The most common activities associated with these accidents were operation of the machine and maintenance and repair. The current methods to safeguard workers near machinery include mechanical guarding around moving components, lockout/tagout of machine power during maintenance and backup alarms for mobile equipment. To decrease accidents further, researchers recommend additional efforts in the development of new control technologies, training materials and dissemination of information on best practices.

Automatic box loader

DOEpatents

Eldridge, Harry H.; Jones, Robert A.; Lindner, Gordon M.; Hight, Paul H.

1976-01-01

This invention relates to a system for repetitively forming an assembly consisting of a single layer of tubes and a row of ferromagnetic armatures underlying the same, electromagnetically conveying the resulting assembly to a position overlying a storage box, and depositing the assembly in the box. The system includes means for simultaneously depositing a row of the armatures on the inclined surface of a tube retainer. Tubes then are rolled down the surface to form a single tube layer bridging the armatures. A magnet assembly carrying electromagnets respectively aligned with the armatures is advanced close to the tube layer, and in the course of this advance is angularly displaced to bring the pole pieces of the electromagnets into parallelism with the tube layer. The magnets then are energized to pick up the assembly. The loaded magnet assembly is retracted to a position overlying the box, and during this retraction is again displaced to bring the pole pieces of the electromagnets into a horizontal plane. Means are provided for inserting the loaded electromagnets in the box and then de-energizing the electromagnets to deposit the assembly therein. The system accomplishes the boxing of fragile tubes at relatively high rates. Because the tubes are boxed as separated uniform layers, subsequent unloading operations are facilitated.

Methods of Collecting and Analyzing Rearward Visibility Data for Agricultural Machinery: Hazard and/or Object Detectability.

PubMed

Ehlers, Shawn G; Field, William E; Ess, Daniel R

2017-01-26

Recent interest in rearward visibility for private, construction, and commercial vehicles and documentation of rearward runovers involving bystanders outside the field of vision of the vehicle operator led to an investigation into the need for enhanced methods of rearward visibility for large, off-highway, agricultural equipment. A review of the literature found limited relevant research and minimal data on incidents involving rearward runovers of bystanders and co-workers. This article reviews the findings regarding the methods identified and tested to collect and analyze rearward visibility data, from the operator's perspective, for large self-propelled agricultural equipment, including the four-wheel drive tractors, combines, agricultural sprayers, and skid-steer loaders that are increasingly found on agricultural production sites. The methods identified, largely drawn from research conducted on private and commercial vehicles, were tested to determine their application in identifying rearward blind spots. These methods are described, and the findings from field-testing of specific machines are provided. Recommendations include establishing an appropriate engineering standard regarding rearward visibility of agricultural equipment with limited rearward vision and the use of rearward alarm systems for warning bystanders of rearward movement. Copyright© by the American Society of Agricultural Engineers.

Fuelcell Prototype Locomotive

DOE Office of Scientific and Technical Information (OSTI.GOV)

David L. Barnes

2007-09-28

An international industry-government consortium is developing a fuelcell hybrid switcher locomotive for commercial railway applications and power-to-grid generation applications. The current phase of this on-going project addresses the practicalities of on-board hydrogen storage, fuelcell technology, and hybridity, all with an emphasis on commercially available products. Through practical evaluation using designs from Vehicle Projects’ Fuelcell-Powered Underground Mine Loader Project, the configuration of the fuelcell switcher locomotive changed from using metal-hydride hydrogen storage and a pure fuelcell power plant to using compressed hydrogen storage, a fuelcell-battery hybrid power plant, and fuelcell stack modules from Ballard Power Systems that have been extensively usedmore » in the Citaro bus program in Europe. The new overall design will now use a RailPower battery hybrid Green Goat™ as the locomotive platform. Keeping the existing lead-acid batteries, we will replace the 205 kW diesel gen-set with 225 kW of net fuelcell power, remove the diesel fuel tank, and place 14 compressed hydrogen cylinders, capable of storing 70 kg of hydrogen at 350 bar, on the roof. A detailed design with associated CAD models will allow a complete build of the fuelcell-battery hybrid switcher locomotive in the next funded phase.« less

Automated 100-Position Specimen Loader and Image Acquisition System for Transmission Electron Microscopy

PubMed Central

Lefman, Jonathan; Morrison, Robert; Subramaniam, Sriram

2007-01-01

We report the development of a novel, multi-specimen imaging system for high-throughput transmission electron microscopy. Our cartridge-based loading system, called the “Gatling”, permits the sequential examination of as many as 100 specimens in the microscope for room temperature electron microscopy using mechanisms for rapid and automated specimen exchange. The software for the operation of the Gatling and automated data acquisition has been implemented in an updated version of our in-house program AutoEM. In the current implementation of the system, the time required to deliver 95 specimens into the microscope and collect overview images from each is about 13 hours. Regions of interest are identified from a low magnification atlas generation from each specimen and an unlimited number of higher magnifications images can be subsequently acquired from these regions using fully automated data acquisition procedures that can be controlled from a remote interface. We anticipate that the availability of the Gatling will greatly accelerate the speed of data acquisition for a variety of applications in biology, materials science and nanotechnology that require rapid screening and image analysis of multiple specimens. PMID:17240161

Drag Reduction and Performance Improvement of Hydraulic Torque Converters with Multiple Biological Characteristics

PubMed Central

Chunbao, Liu; Changsuo, Liu; Yubo, Zhang

2016-01-01

Fish-like, dolphin-like, and bionic nonsmooth surfaces were employed in a hydraulic torque converter to achieve drag reduction and performance improvement, which were aimed at reducing profile loss, impacting loss and friction loss, respectively. YJSW335, a twin turbine torque converter, was bionically designed delicately. The biological characteristics consisted of fish-like blades in all four wheels, dolphin-like structure in the first turbine and the stator, and nonsmooth surfaces in the pump. The prediction performance of bionic YJSW335, obtained by computational fluid dynamics simulation, was improved compared with that of the original model, and then it could be proved that drag reduction had been achieved. The mechanism accounting for drag reduction of three factors was also investigated. After bionic design, the torque ratio and the highest efficiencies of YJSW335 were both advanced, which were very difficult to achieve through traditional design method. Moreover, the highest efficiency of the low speed area and high speed area is 85.65% and 86.32%, respectively. By economic matching analysis of the original and bionic powertrains, the latter can significantly reduce the fuel consumption and improve the operating economy of the loader. PMID:27752220

Mobile camera-space manipulation

NASA Technical Reports Server (NTRS)

Seelinger, Michael J. (Inventor); Yoder, John-David S. (Inventor); Skaar, Steven B. (Inventor)

2001-01-01

The invention is a method of using computer vision to control systems consisting of a combination of holonomic and nonholonomic degrees of freedom such as a wheeled rover equipped with a robotic arm, a forklift, and earth-moving equipment such as a backhoe or a front-loader. Using vision sensors mounted on the mobile system and the manipulator, the system establishes a relationship between the internal joint configuration of the holonomic degrees of freedom of the manipulator and the appearance of features on the manipulator in the reference frames of the vision sensors. Then, the system, perhaps with the assistance of an operator, identifies the locations of the target object in the reference frames of the vision sensors. Using this target information, along with the relationship described above, the system determines a suitable trajectory for the nonholonomic degrees of freedom of the base to follow towards the target object. The system also determines a suitable pose or series of poses for the holonomic degrees of freedom of the manipulator. With additional visual samples, the system automatically updates the trajectory and final pose of the manipulator so as to allow for greater precision in the overall final position of the system.

Evaluate fundamental approaches to longwall dust control. Phase III report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babbitt, C.; Bartlett, P.; Kelly, J.

1984-03-31

The overall objective of the contract is to evaluate the effectiveness of available dust control technology for double-drum shearer longwall sections in a coordinated, systematic program at a few longwall test sections and to make the results available to the entire coal mining industry. This program is investigating nine different dust control techniques. These nine subprograms encompass a broad range of dust control measures ranging from administrative controls to new hardware. They span not only presently employed methods but also those recently adopted in the United States and those proposed for the future. This report documents the Phase III effortmore » on each of the subprograms. For clarity, the report is divided in sections by subprogram as follows: Section 2, Subprogram A - passive barriers/spray air movers for dust control; Section 3, Subprogram B - practical aspects of deep cutting; Section 4, Subprogram C - stage loader dust control; Section 5, Subprogram D - longwall automation technology; Section 6, Subprogram E - longwall application of ventilation curtains; Section 7, Subprogram F - reversed drum rotation; Section 8, Subprogram G - reduction of shield generated dust; Section 9, Subprogram H - air canopies for longwalls; and Section 10, Subprogram I - mining practices. 43 figures, 11 tables.« less

Simulation Based Investigation of Different Fleet Management Paradigms in Open Pit Mines-A Case Study of Sungun Copper Mine / Symulacje I Badania Różnych Paradygmatów Wykorzystania Floty Pojazdów I Urządzeń W Kopalniach Odkrywkowych. Studium Przypadku: Kopalnia Miedzi W Sungun

NASA Astrophysics Data System (ADS)

Hashemi, Ali Saadatmand; Sattarvand, Javad

2015-03-01

Using simulation modeling, different management systems of the open pit mining equipment including non-dispatching, dispatching and blending solutions have been studied for the Sungun copper mine. Developed model has the capability of considering detailed features of both loading and hauling equipment. Productivity assessment scenarios have been established on the constructed model and the outputs revealed the noteworthy impact of the match factor of the trucks to the loaders on the production rate by over 40%. A dispatching simulation model with the objective function of minimizing truck waiting times have been developed and 7.8% improvement obtained by applying a flexible assignment of the trucks for the loaders compared to the fixed assignment system. Finally ore grade blending control unit has been introduced into the model. Getting the advantages of the newly added module it became possible to monitor the portion of material excavated from different operating benches and control truck dispatching rules for keeping the overall ore grade exactly at desired value. Przy użyciu modeli symulacyjnych zbadano różnorodne systemy zarządzania flotą pojazdów i urządzeń w kopalni odkrywkowej (wydawanie dyspozycji przewozu, wstrzymywanie przewozu oraz rozwiązania kwestii mieszania o rud o różnej zawartości pierwiastka użytecznego) na przykładzie kopalni miedzi Sungun. Opracowany model uwzględnia szczegółowe cechy sprzętu przeładunkowego oraz transportowego. Na podstawie modelu opracowano następnie scenariusze oceny wydajności, a wyniki jednoznacznie wykazały wielką wagę odpowiedniego skojarzenia ilości pojazdów i ładowarek. Opracowano model symulacyjny kierowania urządzeń do pracy, jako funkcję celu przyjmujący minimalizacje czasu przestoju ciężarówek. Uzyskano wynik lepszy o 7.8% poprzez elastyczne przydzielania pojazdów do ładowarek w porównaniu do systemu trwałego ich do siebie przypisania. W ostatnim etapie dodano do modelu system kontroli procesu mieszania rud o rozmaitej zawartości pierwiastka użytecznego. Korzystając z nowo-dodanego modułu, możliwe stało się monitorowanie porcji materiału wybieranego z poszczególnych poziomów i kontrolowanie rozsyłanych ciężarówek tak, by w skali całej kopalni możliwe było ciągłe utrzymanie zawartości pierwiastka użytecznego na żądanym poziomie.

Bioaerosol exposure during refuse collection: results of field studies in the real-life situation.

PubMed

Neumann, H D; Balfanz, J; Becker, G; Lohmeyer, M; Mathys, W; Raulf-Heimsoth, M

2002-07-03

To determine the bioaerosol exposure of refuse collectors, field measurements were performed under real working conditions within the framework of a research project. Influencing variables such as different types of refuse, community structure, collection interval and season were taken into account. Overall, 1612 samples were taken in towns of Westfalia, Germany. With workplace levels on a scale of 10(3) to less than 10(4) CFU/m3 for the loader, the results show a surprisingly low total fungi concentration in comparison with earlier studies. Total bacteria concentrations, in contrast, were largely on a scale of 10(4) CFU/m3, with 10(5) CFU/m3 being registered sporadically, especially in apartment-block districts. Endotoxin levels were high especially in the summer months, occasionally reaching values of more than 50 EU/m3, whereas they were normally below 10 EU/m3 in autumn and winter. Inside the cab, the exposure level for the entire spectrum was at least one power of ten lower. The factors believed to account primarily for the low total fungi concentration were workplace hygiene, the prevailing 1-week collection interval, and the low in-process exposure time resulting from the effective deployment of automatic lifting devices. In contrast, the type of refuse was not found to have a significant influence.

Greenhouse gas emissions during co-composting of calf mortalities with manure.

PubMed

Xu, Shanwei; Hao, Xiying; Stanford, Kim; McAllister, Tim A; Larney, Francis J; Wang, Jingguo

2007-01-01

Composting may be a viable on-farm option for disposal of cattle carcasses. This study investigated greenhouse gas emissions during co-composting of calf mortalities with manure. Windrows were constructed that contained manure + straw (control compost [CK]) or manure + straw + calf mortalities (CM) using two technologies: a tractor-mounted front-end loader or a shredder bucket. Composting lasted 289 d. The windrows were turned twice (on Days 72 and 190), using the same technology used in their creation. Turning technology had no effect on greenhouse gas emissions or the properties of the final compost. The CO2 (75.2 g d(-1) m(-2)), CH4 (2.503 g d(-1) m(-2)), and N2O (0.370 g d(-1) m(-2)) emissions were higher (p < 0.05) in CM than in CK (25.7, 0.094, and 0.076 g d(-1) m(-2) for CO2, CH4, and N2O, respectively), which reflected differences in materials used to construct the compost windrows and therefore their total C and total N contents. The final CM compost had higher (p < 0.05) total N, total C, and mineral N content (NO3*+ NO2* + NH4+) than did CK compost and therefore has greater agronomic value as a fertilizer.

PPDMs-a resource for mapping small molecule bioactivities from ChEMBL to Pfam-A protein domains.

PubMed

Kruger, Felix A; Gaulton, Anna; Nowotka, Michal; Overington, John P

2015-03-01

PPDMs is a resource that maps small molecule bioactivities to protein domains from the Pfam-A collection of protein families. Small molecule bioactivities mapped to protein domains add important precision to approaches that use protein sequence searches alignments to assist applications in computational drug discovery and systems and chemical biology. We have previously proposed a mapping heuristic for a subset of bioactivities stored in ChEMBL with the Pfam-A domain most likely to mediate small molecule binding. We have since refined this mapping using a manual procedure. Here, we present a resource that provides up-to-date mappings and the possibility to review assigned mappings as well as to participate in their assignment and curation. We also describe how mappings provided through the PPDMs resource are made accessible through the main schema of the ChEMBL database. The PPDMs resource and curation interface is available at https://www.ebi.ac.uk/chembl/research/ppdms/pfam_maps. The source-code for PPDMs is available under the Apache license at https://github.com/chembl/pfam_maps. Source code is available at https://github.com/chembl/pfam_map_loader to demonstrate the integration process with the main schema of ChEMBL. © The Author 2014. Published by Oxford University Press.

Life cycle inventory energy consumption and emissions for biodiesel versus petroleum diesel fueled construction vehicles.

PubMed

Pang, Shih-Hao; Frey, H Christopher; Rasdorf, William J

2009-08-15

Substitution of soy-based biodiesel fuels for petroleum diesel will alter life cycle emissions for construction vehicles. A life cycle inventory was used to estimate fuel cycle energy consumption and emissions of selected pollutants and greenhouse gases. Real-world measurements using a portable emission measurement system (PEMS) were made forfive backhoes, four front-end loaders, and six motor graders on both fuels from which fuel consumption and tailpipe emission factors of CO, HC, NO(x), and PM were estimated. Life cycle fossil energy reductions are estimated it 9% for B20 and 42% for B100 versus petroleum diesel based on the current national energy mix. Fuel cycle emissions will contribute a larger share of total life cycle emissions as new engines enter the in-use fleet. The average differences in life cycle emissions for B20 versus diesel are: 3.5% higher for NO(x); 11.8% lower for PM, 1.6% higher for HC, and 4.1% lower for CO. Local urban tailpipe emissions are estimated to be 24% lower for HC, 20% lower for CO, 17% lower for PM, and 0.9% lower for NO(x). Thus, there are environmental trade-offs such as for rural vs urban areas. The key sources of uncertainty in the B20 LCI are vehicle emission factors.

Extending laboratory automation to the wards: effect of an innovative pneumatic tube system on diagnostic samples and transport time.

PubMed

Suchsland, Juliane; Winter, Theresa; Greiser, Anne; Streichert, Thomas; Otto, Benjamin; Mayerle, Julia; Runge, Sören; Kallner, Anders; Nauck, Matthias; Petersmann, Astrid

2017-02-01

The innovative pneumatic tube system (iPTS) transports one sample at a time without the use of cartridges and allows rapid sending of samples directly into the bulk loader of a laboratory automation system (LAS). We investigated effects of the iPTS on samples and turn-around time (TAT). During transport, a mini data logger recorded the accelerations in three dimensions and reported them in arbitrary area under the curve (AUC) units. In addition representative quantities of clinical chemistry, hematology and coagulation were measured and compared in 20 blood sample pairs transported by iPTS and courier. Samples transported by iPTS were brought to the laboratory (300 m) within 30 s without adverse effects on the samples. The information retrieved from the data logger showed a median AUC of 7 and 310 arbitrary units for courier and iPTS transport, respectively. This is considerably below the reported limit for noticeable hemolysis of 500 arbitrary units. iPTS reduces TAT by reducing the hands-on time and a fast transport. No differences in the measurement results were found for any of the investigated 36 analytes between courier and iPTS transport. Based on these findings the iPTS was cleared for clinical use in our hospital.

Development of a Portable Knee Rehabilitation Device That Uses Mechanical Loading.

PubMed

Fitzwater, Daric; Dodge, Todd; Chien, Stanley; Yokota, Hiroki; Anwar, Sohel

2013-12-01

Joint loading is a recently developed mechanical modality, which potentially provides a therapeutic regimen to activate bone formation and prevent degradation of joint tissues. To our knowledge, however, few joint loading devices are available for clinical or point-of-care applications. Using a voice-coil actuator, we developed an electromechanical loading system appropriate for human studies and preclinical trials that should prove both safe and effective. Two specific tasks for this loading system were development of loading conditions (magnitude and frequency) suitable for humans, and provision of a convenient and portable joint loading apparatus. Desktop devices have been previously designed to evaluate the effects of various loading conditions using small and large animals. However, a portable knee loading device is more desirable from a usability point of view. In this paper, we present such a device that is designed to be portable, providing a compact, user-friendly loader. The portable device was employed to evaluate its capabilities using a human knee model. The portable device was characterized for force-pulse width modulation duty cycle and loading frequency properties. The results demonstrate that the device is capable of producing the necessary magnitude of forces at appropriate frequencies to promote the stimulation of bone growth and which can be used in clinical studies for further evaluations.

Fabrication and Analysis Signal Optical Fiber Sensor Based On Bend Loss for Weight in Motion Applications

NASA Astrophysics Data System (ADS)

Aftah Syukron, Ahmad; Marzuki, Ahmad; Setyawan, Ary

2017-11-01

Road network plays very important role in economic development. Overweight is one of the main factors contributing to road damage. To minimize this factor, road authority has to make sure that all vehicles operate in according to maximum vehicle regulation set by the government. The one solution can use from this problem is Weight in motion (WIM) technology. WIM technology allows measuring vehicle weight quickly. The sensor is one of the important components in the WIM system. This paper presents a model of WIM fiber sensor work based on bend loss. Fiber sensor has made by coiling optical fiber. Coiling optical fiber has managed in the elliptical shape rubber coil. Rubber coil then is planted in the pad of sensor. The principle of this sensor is a detecting of the shift light intensity output of optical fiber when the vehicles a passing through on fiber sensor. Loading was carried out using loaded truck model. Data was carried out with variations of load and load positions in the truck. The results can be concluded that the shift light intensity is greater with the more shift loads. The loader of the truck has also resulted in the greater loss. Loads in the truck distributed on the axles due to the position of loads.

Implementing Multidisciplinary and Multi-Zonal Applications Using MPI

NASA Technical Reports Server (NTRS)

Fineberg, Samuel A.

1995-01-01

Multidisciplinary and multi-zonal applications are an important class of applications in the area of Computational Aerosciences. In these codes, two or more distinct parallel programs or copies of a single program are utilized to model a single problem. To support such applications, it is common to use a programming model where a program is divided into several single program multiple data stream (SPMD) applications, each of which solves the equations for a single physical discipline or grid zone. These SPMD applications are then bound together to form a single multidisciplinary or multi-zonal program in which the constituent parts communicate via point-to-point message passing routines. Unfortunately, simple message passing models, like Intel's NX library, only allow point-to-point and global communication within a single system-defined partition. This makes implementation of these applications quite difficult, if not impossible. In this report it is shown that the new Message Passing Interface (MPI) standard is a viable portable library for implementing the message passing portion of multidisciplinary applications. Further, with the extension of a portable loader, fully portable multidisciplinary application programs can be developed. Finally, the performance of MPI is compared to that of some native message passing libraries. This comparison shows that MPI can be implemented to deliver performance commensurate with native message libraries.

DPOI: Distributed software system development platform for ocean information service

NASA Astrophysics Data System (ADS)

Guo, Zhongwen; Hu, Keyong; Jiang, Yongguo; Sun, Zhaosui

2015-02-01

Ocean information management is of great importance as it has been employed in many areas of ocean science and technology. However, the developments of Ocean Information Systems (OISs) often suffer from low efficiency because of repetitive work and continuous modifications caused by dynamic requirements. In this paper, the basic requirements of OISs are analyzed first, and then a novel platform DPOI is proposed to improve development efficiency and enhance software quality of OISs by providing off-the-shelf resources. In the platform, the OIS is decomposed hierarchically into a set of modules, which can be reused in different system developments. These modules include the acquisition middleware and data loader that collect data from instruments and files respectively, the database that stores data consistently, the components that support fast application generation, the web services that make the data from distributed sources syntactical by use of predefined schemas and the configuration toolkit that enables software customization. With the assistance of the development platform, the software development needs no programming and the development procedure is thus accelerated greatly. We have applied the development platform in practical developments and evaluated its efficiency in several development practices and different development approaches. The results show that DPOI significantly improves development efficiency and software quality.

The logic of DNA replication in double-stranded DNA viruses: insights from global analysis of viral genomes

PubMed Central

Kazlauskas, Darius; Krupovic, Mart; Venclovas, Česlovas

2016-01-01

Abstract Genomic DNA replication is a complex process that involves multiple proteins. Cellular DNA replication systems are broadly classified into only two types, bacterial and archaeo-eukaryotic. In contrast, double-stranded (ds) DNA viruses feature a much broader diversity of DNA replication machineries. Viruses differ greatly in both completeness and composition of their sets of DNA replication proteins. In this study, we explored whether there are common patterns underlying this extreme diversity. We identified and analyzed all major functional groups of DNA replication proteins in all available proteomes of dsDNA viruses. Our results show that some proteins are common to viruses infecting all domains of life and likely represent components of the ancestral core set. These include B-family polymerases, SF3 helicases, archaeo-eukaryotic primases, clamps and clamp loaders of the archaeo-eukaryotic type, RNase H and ATP-dependent DNA ligases. We also discovered a clear correlation between genome size and self-sufficiency of viral DNA replication, the unanticipated dominance of replicative helicases and pervasive functional associations among certain groups of DNA replication proteins. Altogether, our results provide a comprehensive view on the diversity and evolution of replication systems in the DNA virome and uncover fundamental principles underlying the orchestration of viral DNA replication. PMID:27112572

The structure of a ring-opened proliferating cell nuclear antigen-replication factor C complex revealed by fluorescence energy transfer.

PubMed

Zhuang, Zhihao; Yoder, Bonita L; Burgers, Peter M J; Benkovic, Stephen J

2006-02-21

Numerous proteins that function in DNA metabolic pathways are known to interact with the proliferating cell nuclear antigen (PCNA). The important function of PCNA in stimulating various cellular activities requires its topological linkage with DNA. Loading of the circular PCNA onto duplex DNA requires the activity of a clamp-loader [replication factor C (RFC)] complex and the energy derived from ATP hydrolysis. The mechanistic and structural details regarding PCNA loading by the RFC complex are still developing. In particular, the positive identification of a long-hypothesized structure of an open clamp-RFC complex as an intermediate in loading has remained elusive. In this study, we capture an open yeast PCNA clamp in a complex with RFC through fluorescence energy transfer experiments. We also follow the topological transitions of PCNA in the various steps of the clamp-loading pathway through both steady-state and stopped-flow fluorescence studies. We find that ATP effectively drives the clamp-loading process to completion with the formation of the closed PCNA bound to DNA, whereas ATPgammaS cannot. The information derived from this work complements that obtained from previous structural and mechanistic studies and provides a more complete picture of a eukaryotic clamp-loading pathway using yeast as a paradigm.

Floodplain Assessment for the Middle Los Alamos Canyon Aggregate Area Investigations in Technical Area 02 at Los Alamos National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hathcock, Charles Dean

The proposed action being assessed in this document occurs in TA-02 in the bottom of Los Alamos Canyon. The DOE proposes to conduct soil sampling at AOC 02-011 (d), AOC 02- 011(a)(ii), and SWMU 02-005, and excavate soils in AOC 02-011(a)(ii) as part of a corrective actions effort. Additional shallow surface soil samples (soil grab samples) will be collected throughout the TA-02 area, including within the floodplain, to perform ecotoxicology studies (Figures 1 and 2). The excavation boundaries in AOC 02-011(a)(ii) are slightly within the delineated 100-year floodplain. The project will use a variety of techniques for soil sampling andmore » remediation efforts to include hand/digging, standard hand auger/sampling, excavation using machinery such as backhoe and front end loader and small drill rig. Heavy equipment will traverse the floodplain and spoils piles will be staged in the floodplain within developed or previously disturbed areas (e.g., existing paved roads and parking areas). The project will utilize and maintain appropriate best management practices (BMPs) to contain excavated materials, and all pollutants, including oil from machinery/vehicles. The project will stabilize disturbed areas as appropriate at the end of the project.« less

Heavy construction equipment noise study using dosimetry and time-motion studies

NASA Astrophysics Data System (ADS)

Spencer, Ellsworth R.; Yantek, David S.

2005-09-01

Noise-induced hearing loss continues to afflict workers in many occupational settings despite longstanding recognition of the problems and well-known methods of prevention and regulations. Sound levels associated with heavy construction equipment range from 80 to 120 dB(A) and power tools commonly used in construction produce sound levels up to 115 dB(A). The focus of the research was to determine the noise exposures of heavy construction equipment operators while documenting the workers' tasks, (i.e., hauling, moving, and/or pushing construction material). Time-motion studies were performed at the construction sites and were used to correlate the noise dosage with the work performed by equipment operators. The cumulative dose for the operator was then plotted with references to work tasks, to identify the tasks that caused the greatest noise exposure. Three construction sites were examined and located in the western Pennsylvania and eastern Ohio areas. The types of construction equipment studied included asphalt pavers, backhoes, bulldozers, compaction equipment, excavators, haul trucks, telehandlers, and wheeled loaders. The results showed that bulldozer operators consistently had the highest noise exposures, ranging from a NIOSH REL (Recommended Exposure Limit) dose of 844% to 25836% and an OSHA PEL (Permissible Exposure Limit) dose of 139% to 1397%.

MPIRUN: A Portable Loader for Multidisciplinary and Multi-Zonal Applications

NASA Technical Reports Server (NTRS)

Fineberg, Samuel A.; Woodrow, Thomas S. (Technical Monitor)

1994-01-01

Multidisciplinary and multi-zonal applications are an important class of applications in the area of Computational Aerosciences. In these codes, two or more distinct parallel programs or copies of a single program are utilized to model a single problem. To support such applications, it is common to use a programming model where a program is divided into several single program multiple data stream (SPMD) applications, each of which solves the equations for a single physical discipline or grid zone. These SPMD applications are then bound together to form a single multidisciplinary or multi-zonal program in which the constituent parts communicate via point-to-point message passing routines. One method for implementing the message passing portion of these codes is with the new Message Passing Interface (MPI) standard. Unfortunately, this standard only specifies the message passing portion of an application, but does not specify any portable mechanisms for loading an application. MPIRUN was developed to provide a portable means for loading MPI programs, and was specifically targeted at multidisciplinary and multi-zonal applications. Programs using MPIRUN for loading and MPI for message passing are then portable between all machines supported by MPIRUN. MPIRUN is currently implemented for the Intel iPSC/860, TMC CM5, IBM SP-1 and SP-2, Intel Paragon, and workstation clusters. Further, MPIRUN is designed to be simple enough to port easily to any system supporting MPI.

Evaluations of in-use emission factors from off-road construction equipment

NASA Astrophysics Data System (ADS)

Cao, Tanfeng; Durbin, Thomas D.; Russell, Robert L.; Cocker, David R.; Scora, George; Maldonado, Hector; Johnson, Kent C.

2016-12-01

Gaseous and particle emissions from construction engines contribute an important fraction of the total air pollutants released into the atmosphere and are gaining increasing regulatory attention. Robust quantification of nitrogen oxides (NOx) and particulate matter (PM) emissions are necessary to inventory the contribution of construction equipment to atmospheric loadings. Theses emission inventories require emissions factors from construction equipment as a function of equipment type and modes of operation. While the development of portable emissions measurement systems (PEMS) has led to increased studies of construction equipment emissions, emissions data are still much more limited than for on-road vehicles. The goal of this research program was to obtain accurate in-use emissions data from a test fleet of newer construction equipment (model year 2002 or later) using a Code of Federal Requirements (CFR) compliant PEMS system. In-use emission measurements were made from twenty-seven pieces of construction equipment, which included four backhoes, six wheel loaders, four excavators, two scrapers (one with two engines), six bulldozers, and four graders. The engines ranged in model year from 2003 to 2012, in rated horsepower (hp) from 92 to 540 hp, and in hours of operation from 24 to 17,149 h. This is the largest study of off-road equipment emissions using 40 CFR part 1065 compliant PEMS equipment for all regulated gaseous and particulate emissions.

Esco2 regulates cx43 expression during skeletal regeneration in the zebrafish fin.

PubMed

Banerji, Rajeswari; Eble, Diane M; Iovine, M Kathryn; Skibbens, Robert V

2016-01-01

Roberts syndrome (RBS) is a rare genetic disorder characterized by craniofacial abnormalities, limb malformation, and often severe mental retardation. RBS arises from mutations in ESCO2 that encodes an acetyltransferase and modifies the cohesin subunit SMC3. Mutations in SCC2/NIPBL (encodes a cohesin loader), SMC3 or other cohesin genes (SMC1, RAD21/MCD1) give rise to a related developmental malady termed Cornelia de Lange syndrome (CdLS). RBS and CdLS exhibit overlapping phenotypes, but RBS is thought to arise through mitotic failure and limited progenitor cell proliferation while CdLS arises through transcriptional dysregulation. Here, we use the zebrafish regenerating fin model to test the mechanism through which RBS-type phenotypes arise. esco2 is up-regulated during fin regeneration and specifically within the blastema. esco2 knockdown adversely affects both tissue and bone growth in regenerating fins-consistent with a role in skeletal morphogenesis. esco2-knockdown significantly diminishes cx43/gja1 expression which encodes the gap junction connexin subunit required for cell-cell communication. cx43 mutations cause the short fin (sof(b123) ) phenotype in zebrafish and oculodentodigital dysplasia (ODDD) in humans. Importantly, miR-133-dependent cx43 overexpression rescues esco2-dependent growth defects. These results conceptually link ODDD to cohesinopathies and provide evidence that ESCO2 may play a transcriptional role critical for human development. © 2015 Wiley Periodicals, Inc.

The logic of DNA replication in double-stranded DNA viruses: insights from global analysis of viral genomes.

PubMed

Kazlauskas, Darius; Krupovic, Mart; Venclovas, Česlovas

2016-06-02

Genomic DNA replication is a complex process that involves multiple proteins. Cellular DNA replication systems are broadly classified into only two types, bacterial and archaeo-eukaryotic. In contrast, double-stranded (ds) DNA viruses feature a much broader diversity of DNA replication machineries. Viruses differ greatly in both completeness and composition of their sets of DNA replication proteins. In this study, we explored whether there are common patterns underlying this extreme diversity. We identified and analyzed all major functional groups of DNA replication proteins in all available proteomes of dsDNA viruses. Our results show that some proteins are common to viruses infecting all domains of life and likely represent components of the ancestral core set. These include B-family polymerases, SF3 helicases, archaeo-eukaryotic primases, clamps and clamp loaders of the archaeo-eukaryotic type, RNase H and ATP-dependent DNA ligases. We also discovered a clear correlation between genome size and self-sufficiency of viral DNA replication, the unanticipated dominance of replicative helicases and pervasive functional associations among certain groups of DNA replication proteins. Altogether, our results provide a comprehensive view on the diversity and evolution of replication systems in the DNA virome and uncover fundamental principles underlying the orchestration of viral DNA replication. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Retrotransposon profiling of RNA polymerase III initiation sites.

PubMed

Qi, Xiaojie; Daily, Kenneth; Nguyen, Kim; Wang, Haoyi; Mayhew, David; Rigor, Paul; Forouzan, Sholeh; Johnston, Mark; Mitra, Robi David; Baldi, Pierre; Sandmeyer, Suzanne

2012-04-01

Although retroviruses are relatively promiscuous in choice of integration sites, retrotransposons can display marked integration specificity. In yeast and slime mold, some retrotransposons are associated with tRNA genes (tDNAs). In the Saccharomyces cerevisiae genome, the long terminal repeat retrotransposon Ty3 is found at RNA polymerase III (Pol III) transcription start sites of tDNAs. Ty1, 2, and 4 elements also cluster in the upstream regions of these genes. To determine the extent to which other Pol III-transcribed genes serve as genomic targets for Ty3, a set of 10,000 Ty3 genomic retrotranspositions were mapped using high-throughput DNA sequencing. Integrations occurred at all known tDNAs, two tDNA relics (iYGR033c and ZOD1), and six non-tDNA, Pol III-transcribed types of genes (RDN5, SNR6, SNR52, RPR1, RNA170, and SCR1). Previous work in vitro demonstrated that the Pol III transcription factor (TF) IIIB is important for Ty3 targeting. However, seven loci that bind the TFIIIB loader, TFIIIC, were not targeted, underscoring the unexplained absence of TFIIIB at those sites. Ty3 integrations also occurred in two open reading frames not previously associated with Pol III transcription, suggesting the existence of a small number of additional sites in the yeast genome that interact with Pol III transcription complexes.

Investigation of sliding DNA clamp dynamics by single-molecule fluorescence, mass spectrometry and structure-based modeling

PubMed Central

Gadkari, Varun V; Harvey, Sophie R; Raper, Austin T; Chu, Wen-Ting; Wang, Jin; Wysocki, Vicki H; Suo, Zucai

2018-01-01

Abstract Proliferating cell nuclear antigen (PCNA) is a trimeric ring-shaped clamp protein that encircles DNA and interacts with many proteins involved in DNA replication and repair. Despite extensive structural work to characterize the monomeric, dimeric, and trimeric forms of PCNA alone and in complex with interacting proteins, no structure of PCNA in a ring-open conformation has been published. Here, we use a multidisciplinary approach, including single-molecule Förster resonance energy transfer (smFRET), native ion mobility-mass spectrometry (IM-MS), and structure-based computational modeling, to explore the conformational dynamics of a model PCNA from Sulfolobus solfataricus (Sso), an archaeon. We found that Sso PCNA samples ring-open and ring-closed conformations even in the absence of its clamp loader complex, replication factor C, and transition to the ring-open conformation is modulated by the ionic strength of the solution. The IM-MS results corroborate the smFRET findings suggesting that PCNA dynamics are maintained in the gas phase and further establishing IM-MS as a reliable strategy to investigate macromolecular motions. Our molecular dynamic simulations agree with the experimental data and reveal that ring-open PCNA often adopts an out-of-plane left-hand geometry. Collectively, these results implore future studies to define the roles of PCNA dynamics in DNA loading and other PCNA-mediated interactions. PMID:29529283

Environmental and economic analyses of waste disposal options for traditional markets in Indonesia.

PubMed

Aye, Lu; Widjaya, E R

2006-01-01

Waste from traditional markets in Indonesia is the second largest stream of municipal solid waste after household waste. It has a higher organic fraction and may have greater potential to be managed on a business scale compared to household wastes. The attributed reason is that in general the wastes generated from traditional markets are more uniform, more concentrated and less hazardous than waste from other sources. This paper presents the results of environmental and economic assessments to compare the options available for traditional market waste disposal in Indonesia. The options compared were composting in labour intensive plants, composting in a centralised plant that utilised a simple wheel loader, centralised biogas production and landfill for electricity production. The current open dumping practice was included as the baseline case. A life cycle assessment (LCA) was used for environmental analysis. All options compared have lower environmental impacts than the current practice of open dumping. The biogas production option has the lowest environmental impacts. A cost-benefit analysis, which considered greenhouse gas savings, was used for the economic assessment. It was found that composting at a centralised plant is the most economically feasible option under the present Indonesian conditions. The approach reported in this study could be applied for 'a pre-feasibility first cut comparison' that includes environmental aspects in a decision-making framework for developing countries even though European emission factors were used.

Pseudomonas protegens Pf-5 favours self-produced siderophore over free-loading in interspecies competition for iron.

PubMed

Sexton, D Joseph; Glover, Rochelle C; Loper, Joyce E; Schuster, Martin

2017-09-01

Many microorganisms compete for extracellular iron using strain-specific chelators known as siderophores. The ferric-siderophore complex limits local access to iron because import requires a suitable cognate receptor. Interestingly, many species carry receptors that enable 'cross-feeding' on heterologous siderophores made by neighboring organisms, although little is known about how this ubiquitous behaviour is regulated. Here, we investigated the soil bacterium Pseudomonas protegens Pf-5, a strain remarkable for its ability to use dozens of heterologous siderophores. We characterized the expression of six pyoverdine-type (PVD) siderophore receptors in response to their cognate PVD. In general, we found expression is tightly regulated to reflect availability of their cognate PVD. In contrast, Pf-5 continues to secrete its own primary siderophore, PVD Pf-5 , despite the capability and opportunity to cross-feed. We demonstrate that this strategy is beneficial in co-culture with a competing PVD PAO1 -producer, P. aeruginosa PAO1. Although Pf-5 can cross-feed on PVD PAO1 , production of PVD Pf-5 is required to maintain a competitive advantage. We attribute this to an antagonistic effect of PVD Pf-5 on the growth of PAO1, presumably through limiting access to iron. Our results demonstrate the benefits of excluding competitors out-weigh the incentives associated with a free-loader lifestyle for Pf-5. © 2017 Society for Applied Microbiology and John Wiley & Sons Ltd.

Alpine Holocene Tree Ring Isotope Records - A Synthesis of a Multi-Proxy Approach in Dendroclimatology

NASA Astrophysics Data System (ADS)

Ziehmer, Malin Michelle; Nicolussi, Kurt; Schlüchter, Christian; Leuenberger, Markus

2017-04-01

High-resolution climate reconstructions based on tree-ring proxies are often limited by the individual segment length of living trees selected at the defined sampling sites, which mostly results in relatively short multi-centennial proxy series. A potential extension of living wood records comprise the addition of subfossil and archeological wood remains resulting in chronologies and associated climate reconstructions which are able to cover a few millennia in central Europe (e.g. Büntgen et al., 2011). However, existing multi-millennial tree-ring width chronologies in central Europe rank among the longest continuous chronologies world-wide and span the entire Holocene (Becker et al., 1993; Nicolussi et al. 2009). So far, these chronologies have mainly been used for dating subfossil wood samples, floating chronologies and archeological artifacts, but only in parts for reconstructing climate. Finds of Holocene wood remains in glacier forefields, peat bogs and small lakes allow us not only to establish such long-term tree-ring width records; further they offer the possibility to establish multi-millennial proxy records for the entire Holocene by using a multi-proxy approach which includes both tree-ring width and triple stable isotope ratios. As temperature limits tree growth at the Alpine upper tree line, the existing tree-ring width records are currently limited to reconstruct a single environmental variable. In the framework of the project Alpine Holocene Tree Ring Isotope Records, we combine tree-ring width, cellulose content as well as carbon, oxygen and hydrogen isotope series in a multi-proxy approach which allows the reconstruction of past environments by combining both Holocene wood remains and recent tree samples from two Alpine tree-line species. For this purpose, α-cellulose is prepared from 5-year tree ring blocks following the procedure after Boettger et al. (2007) and subsequently crushed by ultrasonic homogenization (Laumer et al., 2009). The cellulose content is determined for each individual sample and carbon, oxygen and hydrogen isotopic ratios are measured simultaneously (Loader et al., 2015). The isotope records of carbon, oxygen and hydrogen show distinct low-frequency trends for the Early- and Mid-Holocene, but the individual series per proxy are often offset in their isotopic signature. As the sampling sites in our study are distributed along a SW-NE transect, the influence of the site conditions (latitude, longitude, elevation, exposition) and the tree species is tested and subsequently a correction is applied to the individual series. In addition, the tree-ring width records operate as a helpful tool in detecting and attributing the influence of larch budmoth outbreaks on the cellulose content and isotope records. We here present a synthesis of the applied multi-proxy approach and its ability to reconstruct Holocene climate variability for the time span from 9000 to 3500 years b2k covering the Early-Holocene (9000 to 7200 years b2k) and Mid-Holocene (7200 to 4200 years b2k) and the transition to the late Holocene (4200 to 3500 years b2k) as well as the recent 400 years including the modern warming. References Becker, B., & Kromer, B. Palaeogeogr. Palaeoclimatol. Palaeoecol., 1993, 103(1): 67-71 Boettger, T., et al. Anal. Chem., 2007, 79: 4603-4612 Büntgen, U. et al. Science, 2011, 331(6017): 578-582 Laumer, W., et al. Rapid Commun. Mass Spectrom., 2009, 23: 1934-1940 Loader, N.J., et al. Anal. Chem., 2015, 87: 376-380 Nicolussi K., et al. The Holocene, 2009, 19(6): 909-920

Visually guided control of movement in the context of multimodal stimulation

NASA Technical Reports Server (NTRS)

Riccio, Gary E.

1991-01-01

Flight simulation has been almost exclusively concerned with simulating the motions of the aircraft. Physically distinct subsystems are often combined to simulate the varieties of aircraft motion. Visual display systems simulate the motion of the aircraft relative to remote objects and surfaces (e.g., other aircraft and the terrain). 'Motion platform' simulators recreate aircraft motion relative to the gravitoinertial vector (i.e., correlated rotation and tilt as opposed to the 'coordinated turn' in flight). 'Control loaders' attempt to simulate the resistance of the aerodynamic medium to aircraft motion. However, there are few operational systems that attempt to simulate the motion of the pilot relative to the aircraft and the gravitoinertial vector. The design and use of all simulators is limited by poor understanding of postural control in the aircraft and its effect on the perception and control of flight. Analysis of the perception and control of flight (real or simulated) must consider that: (1) the pilot is not rigidly attached to the aircraft; and (2) the pilot actively monitors and adjusts body orientation and configuration in the aircraft. It is argued that this more complete approach to flight simulation requires that multimodal perception be considered as the rule rather than the exception. Moreover, the necessity of multimodal perception is revealed by emphasizing the complementarity rather than the redundancy among perceptual systems. Finally, an outline is presented for an experiment to be conducted at NASA ARC. The experiment explicitly considers possible consequences of coordination between postural and vehicular control.

A pH/enzyme-responsive polymer film consisting of Eudragit FS 30 D and arabinoxylane as a potential material formulation for colon-specific drug delivery system.

PubMed

Rabito, Mirela Fulgencio; Reis, Adriano Valim; Freitas, Adonilson dos Reis; Tambourgi, Elias Basile; Cavalcanti, Osvaldo Albuquerque

2012-01-01

Polymer film based on pH-dependent Eudragit FS 30 D acrylic polymer in association with arabinoxylane, a polysaccharide issued from gum psyllium, was produced by way of solvent casting. Physical-chemical characterization of the polymer film samples was performed by means of thermogravimetry (TGA), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). Furthermore, water-equilibrium swelling index (I(s)) and weight loss of the films in KCl buffer solution of pH 1.2, in KH(2)PO(4) buffer solution of pH 5.0, or in KH(2)PO(4) buffer solution of pH 5.0 consisting of 4% enzyme Pectinex 3X-L (w/v) were also carried out for the film characterization. No chemical interactions between the Eudragit FS 30 D and the arabinoxylane polymer chains were evidenced, thus suggesting that the film-forming polymer structure was obtained from a physical mixture of both polymers. The arabinoxylane-loader films showed a more pronounced weight loss after their immersion in buffer solution containing enzyme Pectinex 3X-L. The introduction of the arabinoxylane makes the film more susceptible to undergo an enzymatic degradation. This meant that the enzyme-dependent propriety issued from the arabinoxylane has been imprinted into the film formulation. This type of polymer film is an interesting system for applications in colon-specific drug delivery system.

Mortality from Parkinson's disease and other causes among a workforce manufacturing paraquat: a retrospective cohort study

PubMed Central

Campbell, Clive

2011-01-01

Objective To assess the risk of Parkinson's disease (PD) and update information on mortality from major causes of death among a UK workforce who manufactured paraquat (PQ) between 1961 and 1995. There have been no previous studies of the incidence of PD among PQ production workers, although much epidemiological literature exists concerning the relationship between pesticides and PD, and interest has focused on PQ and its users. Methods The cohort included all employees who had ever worked on any of the four plants at Widnes where PQ was manufactured between 1961 and 1995, and 926 male and 42 female workers were followed through 30 June 2009. Mortalities for males were compared with national and local rates, including rates for PD as a mentioned cause of death. Results Overall, 307 workers had died by 30 June 2009. One male death was due to PD, and no other death certificate mentioned PD. At least 3.3 death certificates of male employees would have been expected to have mentioned PD (standardised mortality ratio=31; 95% CI 1 to 171). Personal monitoring results were indicative that the exposure of a PQ production worker on a daily basis was at least comparable with that of a PQ sprayer or mixer/loader. Reduced mortalities compared with local rates were found for major causes of death. Conclusions The study provided no evidence of an increased risk of PD, or increased mortalities from other causes. PMID:22080539

Launching large computing applications on a disk-less cluster

NASA Astrophysics Data System (ADS)

Schwemmer, Rainer; Caicedo Carvajal, Juan Manuel; Neufeld, Niko

2011-12-01

The LHCb Event Filter Farm system is based on a cluster of the order of 1.500 disk-less Linux nodes. Each node runs one instance of the filtering application per core. The amount of cores in our current production environment is 8 per machine for the old cluster and 12 per machine on extension of the cluster. Each instance has to load about 1.000 shared libraries, weighting 200 MB from several directory locations from a central repository. The repository is currently hosted on a SAN and exported via NFS. The libraries are all available in the local file system cache on every node. Loading a library still causes a huge number of requests to the server though, because the loader will try to probe every available path. Measurements show there are between 100.000-200.000 calls per application instance start up. Multiplied by the numbers of cores in the farm, this translates into a veritable DDoS attack on the servers, which lasts several minutes. Since the application is being restarted frequently, a better solution had to be found.scp Rolling out the software to the nodes is out of the question, because they have no disks and the software in it's entirety is too large to put into a ram disk. To solve this problem we developed a FUSE based file systems which acts as a permanent, controllable cache that keeps the essential files that are necessary in stock.

Use of IT platform in determination of efficiency of mining machines

NASA Astrophysics Data System (ADS)

Brodny, Jarosław; Tutak, Magdalena

2018-01-01

Determination of effective use of mining devices has very significant meaning for mining enterprises. High costs of their purchase and tenancy cause that these enterprises tend to the best use of possessed technical potential. However, specifics of mining production causes that this process not always proceeds without interferences. Practical experiences show that determination of objective measure of utilization of machine in mining enterprise is not simple. In the paper a proposition for solution of this problem is presented. For this purpose an IT platform and overall efficiency model OEE were used. This model enables to evaluate the machine in a range of its availability performance and quality of product, and constitutes a quantitative tool of TPM strategy. Adapted to the specificity of mining branch the OEE model together with acquired data from industrial automatic system enabled to determine the partial indicators and overall efficiency of tested machines. Studies were performed for a set of machines directly use in coal exploitation process. They were: longwall-shearer and armoured face conveyor, and beam stage loader. Obtained results clearly indicate that degree of use of machines by mining enterprises are unsatisfactory. Use of IT platforms will significantly facilitate the process of registration, archiving and analytical processing of the acquired data. In the paper there is presented methodology of determination of partial indices and total OEE together with a practical example of its application for investigated machines set. Also IT platform was characterized for its construction, function and application.

Socioeconomic and occupational risk factors for venous thromboembolism in Sweden: a nationwide epidemiological study.

PubMed

Zöller, Bengt; Li, Xinjun; Sundquist, Jan; Sundquist, Kristina

2012-05-01

Our aims were to investigate possible associations between hospitalisation for venous thromboembolism (VTE) and socioeconomic and occupational factors. A nationwide database was constructed by linking Swedish census data to the Hospital Discharge Register (1990-2007). Hospital diagnoses of VTE were based on the International Classification of Diseases. Standardised incidence ratios were calculated for different socioeconomic and occupational groups. A total of 43063 individuals aged >20 years were hospitalised for VTE. Individuals with >12 years of education were at lower risk for VTE. Blue-collar workers, farmers, and non-employed individuals had higher risks for VTE, and white collar workers and professionals lower risks. In males and/or females, risks for VTE were increased for assistant nurses; farmers; miners and quarry workers; mechanics, iron and metalware workers; wood workers; food manufacture workers; packers; loaders and warehouse workers; public safety and protection workers; cooks and stewards; home helpers; building caretakers; and cleaners. Decreased risks were observed for technical, chemical, physical, and biological workers; physicians; dentists; nurses; other health and medical workers; teachers, religious, juridical, and other social science-related workers; artistic workers; clerical workers; sale agents; and fishermen, whalers and sealers. High educational level and several occupations requiring high levels of education were protective against VTE, while the risks for VTE were increased for farmers, blue-collar workers and non-employed individuals. The mechanisms are unknown but it might involve persistent psychosocial stress related to low socioeconomic and occupational status. Copyright © 2011 Elsevier Ltd. All rights reserved.

Intracellular pH regulation in unstimulated Calliphora salivary glands is Na+ dependent and requires V-ATPase activity.

PubMed

Schewe, Bettina; Blenau, Wolfgang; Walz, Bernd

2012-04-15

Salivary gland cells of the blowfly Calliphora vicina have a vacuolar-type H(+)-ATPase (V-ATPase) that lies in their apical membrane and energizes the secretion of a KCl-rich primary saliva upon stimulation with serotonin (5-hydroxytryptamine). Whether and to what extent V-ATPase contributes to intracellular pH (pH(i)) regulation in unstimulated gland cells is unknown. We used the fluorescent dye BCECF to study intracellular pH(i) regulation microfluorometrically and show that: (1) under resting conditions, the application of Na(+)-free physiological saline induces an intracellular alkalinization attributable to the inhibition of the activity of a Na(+)-dependent glutamate transporter; (2) the maintenance of resting pH(i) is Na(+), Cl(-), concanamycin A and DIDS sensitive; (3) recovery from an intracellular acid load is Na(+) sensitive and requires V-ATPase activity; (4) the Na(+)/H(+) antiporter is not involved in pH(i) recovery after a NH(4)Cl prepulse; and (5) at least one Na(+)-dependent transporter and the V-ATPase maintain recovery from an intracellular acid load. Thus, under resting conditions, the V-ATPase and at least one Na(+)-dependent transporter maintain normal pH(i) values of pH 7.5. We have also detected the presence of a Na(+)-dependent glutamate transporter, which seems to act as an acid loader. Despite this not being a common pH(i)-regulating transporter, its activity affects steady-state pH(i) in C. vicina salivary gland cells.

Tripal: a construction toolkit for online genome databases.

PubMed

Ficklin, Stephen P; Sanderson, Lacey-Anne; Cheng, Chun-Huai; Staton, Margaret E; Lee, Taein; Cho, Il-Hyung; Jung, Sook; Bett, Kirstin E; Main, Doreen

2011-01-01

As the availability, affordability and magnitude of genomics and genetics research increases so does the need to provide online access to resulting data and analyses. Availability of a tailored online database is the desire for many investigators or research communities; however, managing the Information Technology infrastructure needed to create such a database can be an undesired distraction from primary research or potentially cost prohibitive. Tripal provides simplified site development by merging the power of Drupal, a popular web Content Management System with that of Chado, a community-derived database schema for storage of genomic, genetic and other related biological data. Tripal provides an interface that extends the content management features of Drupal to the data housed in Chado. Furthermore, Tripal provides a web-based Chado installer, genomic data loaders, web-based editing of data for organisms, genomic features, biological libraries, controlled vocabularies and stock collections. Also available are Tripal extensions that support loading and visualizations of NCBI BLAST, InterPro, Kyoto Encyclopedia of Genes and Genomes and Gene Ontology analyses, as well as an extension that provides integration of Tripal with GBrowse, a popular GMOD tool. An Application Programming Interface is available to allow creation of custom extensions by site developers, and the look-and-feel of the site is completely customizable through Drupal-based PHP template files. Addition of non-biological content and user-management is afforded through Drupal. Tripal is an open source and freely available software package found at http://tripal.sourceforge.net.

Roles of the checkpoint sensor clamp Rad9-Rad1-Hus1 (911)-complex and the clamp loaders Rad17-RFC and Ctf18-RFC in Schizosaccharomyces pombe telomere maintenance.

PubMed

Khair, Lyne; Chang, Ya-Ting; Subramanian, Lakxmi; Russell, Paul; Nakamura, Toru M

2010-06-01

While telomeres must provide mechanisms to prevent DNA repair and DNA damage checkpoint factors from fusing chromosome ends and causing permanent cell cycle arrest, these factors associate with functional telomeres and play critical roles in the maintenance of telomeres. Previous studies have established that Tel1 (ATM) and Rad3 (ATR) kinases play redundant but essential roles for telomere maintenance in fission yeast. In addition, the Rad9-Rad1-Hus1 (911) and Rad17-RFC complexes work downstream of Rad3 (ATR) in fission yeast telomere maintenance. Here, we investigated how 911, Rad17-RFC and another RFC-like complex Ctf18-RFC contribute to telomere maintenance in fission yeast cells lacking Tel1 and carrying a novel hypomorphic allele of rad3 (DBD-rad3), generated by the fusion between the DNA binding domain (DBD) of the fission yeast telomere capping protein Pot1 and Rad3. Our investigations have uncovered a surprising redundancy for Rad9 and Hus1 in allowing Rad1 to contribute to telomere maintenance in DBD-rad3 tel1 cells. In addition, we found that Rad17-RFC and Ctf18-RFC carry out redundant telomere maintenance functions in DBD-rad3 tel1 cells. Since checkpoint sensor proteins are highly conserved, genetic redundancies uncovered here may be relevant to telomere maintenance and detection of DNA damage in other eukaryotes.

Roles of the Checkpoint Sensor Clamp Rad9-Rad1-Hus1 (911)-Complex and the Clamp Loaders Rad17-RFC and Ctf18-RFC in Schizosaccharomyces pombe Telomere Maintenance

PubMed Central

Khair, Lyne; Chang, Ya-Ting; Subramanian, Lakxmi; Russell, Paul; Nakamura, Toru M.

2011-01-01

While telomeres must provide mechanisms to prevent DNA repair and DNA damage checkpoint factors from fusing chromosome ends and causing permanent cell cycle arrest, these factors associate with functional telomeres and play critical roles in the maintenance of telomeres. Previous studies have established that Tel1 (ATM) and Rad3 (ATR) kinases play redundant but essential roles for telomere maintenance in fission yeast. In addition, the Rad9-Rad1-Hus1 (911) and Rad17-RFC complexes work downstream of Rad3 (ATR) in fission yeast telomere maintenance. Here, we investigated how 911, Rad17-RFC and another RFC-like complex Ctf18-RFC contribute to telomere maintenance in fission yeast cells lacking Tel1 and carrying a novel hypomorphic allele of rad3 (DBD-rad3), generated by the fusion between the DNA binding domain (DBD) of the fission yeast telomere capping protein Pot1 and Rad3. Our investigations have uncovered a surprising redundancy for Rad9 and Hus1 in allowing Rad1 to contribute to telomere maintenance in DBD-rad3 tel1Δ cells. In addition, we found that Rad17-RFC and Ctf18-RFC carry out redundant telomere maintenance functions in DBD-rad3 tel1Δ cells. Since checkpoint sensor proteins are highly conserved, genetic redundancies uncovered here may be relevant to telomere maintenance and detection of DNA damage in other eukaryotes. PMID:20505337

Inelastic response of metal matrix composites under biaxial loading

NASA Technical Reports Server (NTRS)

Mirzadeh, F.; Pindera, Marek-Jerzy; Herakovich, Carl T.

1990-01-01

Elements of the analytical/experimental program to characterize the response of silicon carbide titanium (SCS-6/Ti-15-3) composite tubes under biaxial loading are outlined. The analytical program comprises prediction of initial yielding and subsequent inelastic response of unidirectional and angle-ply silicon carbide titanium tubes using a combined micromechanics approach and laminate analysis. The micromechanics approach is based on the method of cells model and has the capability of generating the effective thermomechanical response of metal matrix composites in the linear and inelastic region in the presence of temperature and time-dependent properties of the individual constituents and imperfect bonding on the initial yield surfaces and inelastic response of (0) and (+ or - 45)sub s SCS-6/Ti-15-3 laminates loaded by different combinations of stresses. The generated analytical predictions will be compared with the experimental results. The experimental program comprises generation of initial yield surfaces, subsequent stress-strain curves and determination of failure loads of the SCS-6/Ti-15-3 tubes under selected loading conditions. The results of the analytical investigation are employed to define the actual loading paths for the experimental program. A brief overview of the experimental methodology is given. This includes the test capabilities of the Composite Mechanics Laboratory at the University of Virginia, the SCS-6/Ti-15-3 composite tubes secured from McDonnell Douglas Corporation, a text fixture specifically developed for combined axial-torsional loading, and the MTS combined axial-torsion loader that will be employed in the actual testing.

[Little known activity of the Czestochowa typhus Institute in 1943 and 1944].

PubMed

Aramowicz, P; Fijałek, J; Lutrzykowski, A

1996-01-01

In 1921 Prof. Rudolf Weigl started manufacturing on an industrial scale a typhus vaccine. Until the beginning of World War Two he organised five companies called Weigl Institute. During the Soviet occupation the Lvov plant became the Lvov Sanitary and Bacteriological Institute and after the town was taken over by the German Army on 1st July 1941, Prof. Weigl became a head of research of the Military Typhus Institute. It consisted of four sections for manufacturing the vaccine. All the produce was mainly despatched to the Russian front and only very little reached the civilians. In November and December 1943 the plant was moved to Czestochowa into a main building in Wilsona str. and two four storey others in Jasnogórska str. Its head became a German doctor Mozer (witness test). It is difficult to state numbers the plant employed there being no data left but according to employees still alive there must have been about a hundred lab. staff and two hundred feeders. The plant was divided into "breeding", "preparatory" and "liofilisation" sections. "The breeding" was for feeders and breeding lice. Cages containing about 30,000 lice were fastened to voluntary feeders for each feeding. Next "loaders" covered a so-called key board with 20 insects and infectors introduced and pressurised solution containing live rickets into a louse intestine. After a six or seven day passage, lice ware dried and their intestines prepared to produce liofilizeate all the staff and their families were inoculated. ...

Modulatory effects of neuropsychopharmaca on intracellular pH of hippocampal neurones in vitro

PubMed Central

Bonnet, Udo; Bingmann, Dieter; Wiltfang, Jens; Scherbaum, Norbert; Wiemann, Martin

2010-01-01

Background and purpose: The intracellular pH (pHi) of neurones is tightly regulated by, for example, membrane-bound acid-exchangers and loaders. Nevertheless, excessive bioelectric activity lowers steady-state pHi. In turn, even a moderate acidification can inhibit neuronal activity, a process believed to be part of a negative feedback loop controlling neuronal excitation. As moclobemide, an antidepressant, and also some antiepileptic drugs can reduce neuronal pHi in hippocampus slices in vitro, we screened a panel of currently used neuropsychopharmaca for comparable effects. Experimental approach: BCECF-AM loaded hippocampal slices were superfused with 16 different neuroleptics, antidepressants and antiepileptics under bicarbonate-buffered conditions. Changes in steady-state pHi of CA3 neurones were measured fluorometrically. Key results: The antipsychotics haloperidol, clozapine, ziprasidone, and the antidepressants amitriptyline, doxepin, trimipramine, citalopram, mirtazapine, as well as the anticonvulsive drug tiagabine reversibly reduced the steady-state pHi by up to 0.35 pH-units in concentrations of 5–50 µM. In contrast, venlafaxine, the anticonvulsants carbamazepine, clonazepam, gabapentin, lamotrigine, zonisamide, and the mood stabilizer lithium had no effect on neuronal pHi. Conclusion and implications: These data substantiate the view that clinically relevant concentrations of neuroleptics and antidepressants can mediate changes in neuronal pHi, which may contribute to their pharmacological mode of action. Effects on pHi should be taken into account when therapeutic or even harmful effects of these drugs are evaluated. PMID:20015293

Environmental and economic analyses of waste disposal options for traditional markets in Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aye, Lu; Widjaya, E.R.

2006-07-01

Waste from traditional markets in Indonesia is the second largest stream of municipal solid waste after household waste. It has a higher organic fraction and may have greater potential to be managed on a business scale compared to household wastes. The attributed reason is that in general the wastes generated from traditional markets are more uniform, more concentrated and less hazardous than waste from other sources. This paper presents the results of environmental and economic assessments to compare the options available for traditional market waste disposal in Indonesia. The options compared were composting in labour intensive plants, composting in amore » centralised plant that utilised a simple wheel loader, centralised biogas production and landfill for electricity production. The current open dumping practice was included as the baseline case. A life cycle assessment (LCA) was used for environmental analysis. All options compared have lower environmental impacts than the current practice of open dumping. The biogas production option has the lowest environmental impacts. A cost-benefit analysis, which considered greenhouse gas savings, was used for the economic assessment. It was found that composting at a centralised plant is the most economically feasible option under the present Indonesian conditions. The approach reported in this study could be applied for 'a pre-feasibility first cut comparison' that includes environmental aspects in a decision-making framework for developing countries even though European emission factors were used.« less

Tripal: a construction toolkit for online genome databases

PubMed Central

Sanderson, Lacey-Anne; Cheng, Chun-Huai; Staton, Margaret E.; Lee, Taein; Cho, Il-Hyung; Jung, Sook; Bett, Kirstin E.; Main, Doreen

2011-01-01

As the availability, affordability and magnitude of genomics and genetics research increases so does the need to provide online access to resulting data and analyses. Availability of a tailored online database is the desire for many investigators or research communities; however, managing the Information Technology infrastructure needed to create such a database can be an undesired distraction from primary research or potentially cost prohibitive. Tripal provides simplified site development by merging the power of Drupal, a popular web Content Management System with that of Chado, a community-derived database schema for storage of genomic, genetic and other related biological data. Tripal provides an interface that extends the content management features of Drupal to the data housed in Chado. Furthermore, Tripal provides a web-based Chado installer, genomic data loaders, web-based editing of data for organisms, genomic features, biological libraries, controlled vocabularies and stock collections. Also available are Tripal extensions that support loading and visualizations of NCBI BLAST, InterPro, Kyoto Encyclopedia of Genes and Genomes and Gene Ontology analyses, as well as an extension that provides integration of Tripal with GBrowse, a popular GMOD tool. An Application Programming Interface is available to allow creation of custom extensions by site developers, and the look-and-feel of the site is completely customizable through Drupal-based PHP template files. Addition of non-biological content and user-management is afforded through Drupal. Tripal is an open source and freely available software package found at http://tripal.sourceforge.net PMID:21959868

Glove-Enabled Computer Operations (GECO): Design and Testing of an Extravehicular Activity Glove Adapted for Human-Computer Interface

NASA Technical Reports Server (NTRS)

Adams, Richard J.; Olowin, Aaron; Krepkovich, Eileen; Hannaford, Blake; Lindsay, Jack I. C.; Homer, Peter; Patrie, James T.; Sands, O. Scott

2013-01-01

The Glove-Enabled Computer Operations (GECO) system enables an extravehicular activity (EVA) glove to be dual-purposed as a human-computer interface device. This paper describes the design and human participant testing of a right-handed GECO glove in a pressurized glove box. As part of an investigation into the usability of the GECO system for EVA data entry, twenty participants were asked to complete activities including (1) a Simon Says Games in which they attempted to duplicate random sequences of targeted finger strikes and (2) a Text Entry activity in which they used the GECO glove to enter target phrases in two different virtual keyboard modes. In a within-subjects design, both activities were performed both with and without vibrotactile feedback. Participants' mean accuracies in correctly generating finger strikes with the pressurized glove were surprisingly high, both with and without the benefit of tactile feedback. Five of the subjects achieved mean accuracies exceeding 99% in both conditions. In Text Entry, tactile feedback provided a statistically significant performance benefit, quantified by characters entered per minute, as well as reduction in error rate. Secondary analyses of responses to a NASA Task Loader Index (TLX) subjective workload assessments reveal a benefit for tactile feedback in GECO glove use for data entry. This first-ever investigation of employment of a pressurized EVA glove for human-computer interface opens up a wide range of future applications, including text "chat" communications, manipulation of procedures/checklists, cataloguing/annotating images, scientific note taking, human-robot interaction, and control of suit and/or other EVA systems.

Glove-Enabled Computer Operations (GECO): Design and Testing of an Extravehicular Activity Glove Adapted for Human-Computer Interface

NASA Technical Reports Server (NTRS)

Adams, Richard J.; Olowin, Aaron; Krepkovich, Eileen; Hannaford, Blake; Lindsay, Jack I. C.; Homer, Peter; Patrie, James T.; Sands, O. Scott

2013-01-01

The Glove-Enabled Computer Operations (GECO) system enables an extravehicular activity (EVA) glove to be dual-purposed as a human-computer interface device. This paper describes the design and human participant testing of a right-handed GECO glove in a pressurized glove box. As part of an investigation into the usability of the GECO system for EVA data entry, twenty participants were asked to complete activities including (1) a Simon Says Games in which they attempted to duplicate random sequences of targeted finger strikes and (2) a Text Entry activity in which they used the GECO glove to enter target phrases in two different virtual keyboard modes. In a within-subjects design, both activities were performed both with and without vibrotactile feedback. Participants mean accuracies in correctly generating finger strikes with the pressurized glove were surprisingly high, both with and without the benefit of tactile feedback. Five of the subjects achieved mean accuracies exceeding 99 in both conditions. In Text Entry, tactile feedback provided a statistically significant performance benefit, quantified by characters entered per minute, as well as reduction in error rate. Secondary analyses of responses to a NASA Task Loader Index (TLX) subjective workload assessments reveal a benefit for tactile feedback in GECO glove use for data entry. This first-ever investigation of employment of a pressurized EVA glove for human-computer interface opens up a wide range of future applications, including text chat communications, manipulation of procedureschecklists, cataloguingannotating images, scientific note taking, human-robot interaction, and control of suit andor other EVA systems.

Reduced-gravity environment hardware demonstrations of a prototype miniaturized flow cytometer and companion microfluidic mixing technology.

PubMed

Phipps, William S; Yin, Zhizhong; Bae, Candice; Sharpe, Julia Z; Bishara, Andrew M; Nelson, Emily S; Weaver, Aaron S; Brown, Daniel; McKay, Terri L; Griffin, DeVon; Chan, Eugene Y

2014-11-13

Until recently, astronaut blood samples were collected in-flight, transported to earth on the Space Shuttle, and analyzed in terrestrial laboratories. If humans are to travel beyond low Earth orbit, a transition towards space-ready, point-of-care (POC) testing is required. Such testing needs to be comprehensive, easy to perform in a reduced-gravity environment, and unaffected by the stresses of launch and spaceflight. Countless POC devices have been developed to mimic laboratory scale counterparts, but most have narrow applications and few have demonstrable use in an in-flight, reduced-gravity environment. In fact, demonstrations of biomedical diagnostics in reduced gravity are limited altogether, making component choice and certain logistical challenges difficult to approach when seeking to test new technology. To help fill the void, we are presenting a modular method for the construction and operation of a prototype blood diagnostic device and its associated parabolic flight test rig that meet the standards for flight-testing onboard a parabolic flight, reduced-gravity aircraft. The method first focuses on rig assembly for in-flight, reduced-gravity testing of a flow cytometer and a companion microfluidic mixing chip. Components are adaptable to other designs and some custom components, such as a microvolume sample loader and the micromixer may be of particular interest. The method then shifts focus to flight preparation, by offering guidelines and suggestions to prepare for a successful flight test with regard to user training, development of a standard operating procedure (SOP), and other issues. Finally, in-flight experimental procedures specific to our demonstrations are described.

Semantics based approach for analyzing disease-target associations.

PubMed

Kaalia, Rama; Ghosh, Indira

2016-08-01

A complex disease is caused by heterogeneous biological interactions between genes and their products along with the influence of environmental factors. There have been many attempts for understanding the cause of these diseases using experimental, statistical and computational methods. In the present work the objective is to address the challenge of representation and integration of information from heterogeneous biomedical aspects of a complex disease using semantics based approach. Semantic web technology is used to design Disease Association Ontology (DAO-db) for representation and integration of disease associated information with diabetes as the case study. The functional associations of disease genes are integrated using RDF graphs of DAO-db. Three semantic web based scoring algorithms (PageRank, HITS (Hyperlink Induced Topic Search) and HITS with semantic weights) are used to score the gene nodes on the basis of their functional interactions in the graph. Disease Association Ontology for Diabetes (DAO-db) provides a standard ontology-driven platform for describing genes, proteins, pathways involved in diabetes and for integrating functional associations from various interaction levels (gene-disease, gene-pathway, gene-function, gene-cellular component and protein-protein interactions). An automatic instance loader module is also developed in present work that helps in adding instances to DAO-db on a large scale. Our ontology provides a framework for querying and analyzing the disease associated information in the form of RDF graphs. The above developed methodology is used to predict novel potential targets involved in diabetes disease from the long list of loose (statistically associated) gene-disease associations. Copyright © 2016 Elsevier Inc. All rights reserved.

Quality control mechanisms exclude incorrect polymerases from the eukaryotic replication fork

PubMed Central

Schauer, Grant D.; O’Donnell, Michael E.

2017-01-01

The eukaryotic genome is primarily replicated by two DNA polymerases, Pol ε and Pol δ, that function on the leading and lagging strands, respectively. Previous studies have established recruitment mechanisms whereby Cdc45-Mcm2-7-GINS (CMG) helicase binds Pol ε and tethers it to the leading strand, and PCNA (proliferating cell nuclear antigen) binds tightly to Pol δ and recruits it to the lagging strand. The current report identifies quality control mechanisms that exclude the improper polymerase from a particular strand. We find that the replication factor C (RFC) clamp loader specifically inhibits Pol ε on the lagging strand, and CMG protects Pol ε against RFC inhibition on the leading strand. Previous studies show that Pol δ is slow and distributive with CMG on the leading strand. However, Saccharomyces cerevisiae Pol δ–PCNA is a rapid and processive enzyme, suggesting that CMG may bind and alter Pol δ activity or position it on the lagging strand. Measurements of polymerase binding to CMG demonstrate Pol ε binds CMG with a Kd value of 12 nM, but Pol δ binding CMG is undetectable. Pol δ, like bacterial replicases, undergoes collision release upon completing replication, and we propose Pol δ–PCNA collides with the slower CMG, and in the absence of a stabilizing Pol δ–CMG interaction, the collision release process is triggered, ejecting Pol δ on the leading strand. Hence, by eviction of incorrect polymerases at the fork, the clamp machinery directs quality control on the lagging strand and CMG enforces quality control on the leading strand. PMID:28069954

Functional characterization of transmembrane intracellular pH regulators and mechanism of alcohol-induced intracellular acidosis in human umbilical cord blood stem cell-like cells.

PubMed

Tsai, Yi-Ting; Liu, Jah-Yao; Lee, Chung-Yi; Tsai, Chien-Sung; Chen, Ming-Hurng; Ou, Chien-Chih; Chen, Wei-Hwa; Loh, Shih-Hurng

2011-12-01

Changing intracellular pH (pHi) exerts considerable influence on many cellular functions. Different pHi regulators, such as the Na-H exchanger (NHE), Na/(Equation is included in full-text article.)symporter, and Cl/OH exchanger (CHE), have been identified in mature mammalian cells. The aims of the present study were to investigate the physiological mechanisms of pHi recovery and to further explore the effects of alcohol on the pHi in human umbilical cord blood CD34 stem cell-like cells (HUCB-CD34STs). HUCB-CD34STs were loaded with the pH-sensitive dye, 2',7'-bis(2-carboxethyl)-5(6)-carboxyfluorescein, to examine pHi. In isolated HUCB-CD34STs, we found that (1) the resting pHi is 7.03 ± 0.02; (2) 2 Na-dependent acid extruders and a Cl-dependent acid loading carrier exist and are functional; (3) alcohol functions in a concentration-dependent manner to reduce pHi and increase NHE activity, but it does not affect CHE activity; and (4) fomepizole, a specific alcohol dehydrogenase inhibitor, does not change the intracellular acidosis and NHE activity-induced by alcohol, whereas 3-amino-1, 2,4-trizole, a specific catalase inhibitor, entirely abolishes these effects. In conclusion, we demonstrate that 2 acid extruders and 1 acid loader (most likely NHE, NBC, and CHE, respectively) functionally existed in HUCB-CD34STs. Additionally, the intracellular acidosis is mainly caused by catalase-mediated alcohol metabolites, which provoke the activity of NHE.

Genetic recombination induced by DNA double-strand break in bacteriophage T4: nature of the left/right bias.

PubMed

Shcherbakov, Victor P; Shcherbakova, Tamara; Plugina, Lidiya; Sizova, Svetlana; Kudryashova, Elena; Granovsky, Igor

2008-06-01

The experimental system combining double-strand breaks (DSBs), produced site-specifically by SegC endonuclease, with the famous advantages of the bacteriophage T4 rII mutant recombination analysis was used here to elucidate the origin of the recombination bias on two sides of the DSB, especially pronounced in gene 39 (topoisomerase II) and gene 59 (41-helicase loader) mutants. Three sources were found to contribute to the bias: (1) the SegC endonuclease may remain bound to the end of the broken DNA and thus protect it from exonuclease degradation; (2) in heteroduplex heterozygotes (HHs), arising as the recombinant products in the left-hand crosses, the transcribed strands are of rII mutant phenotype, so they, in contrast to the right-hand HHs, do not produce plaques on the lawn of the lambda-lysogenic host; and (3) the intrinsic polarity of T4 chromosome, reflected in transcription, may be a cause for discrimination of promoter-proximal and promoter-distal DNA sequences. It is shown that the apparent recombination bias does not imply one-sidedness of the DSB repair but just reflects a different depth of the end processing. It is inferred that the cause, underlying the "intrinsic" bias, might be interference between strand exchange and transcription. Topoisomerase and helicase functions are necessary to turn the process in favor of strand exchange. The idea is substantiated that the double-stranded to single-stranded DNA transition edge (not ss-DNA tip) serves as an actual recombinogenic element.

3D gain modeling of LMJ and NIF amplifiers

NASA Astrophysics Data System (ADS)

LeTouze, Geoffroy; Cabourdin, Olivier; Mengue, J. F.; Guenet, Mireille; Grebot, Eric; Seznec, Stephane E.; Jancaitis, Kenneth S.; Marshall, Christopher D.; Zapata, Luis E.; Erlandson, A. E.

1999-07-01

A 3D ray-trace model has been developed to predict the performance of flashlamp pumped laser amplifiers. The computer program, written in C++, includes a graphical display option using the Open Inventor library, as well as a parser and a loader allowing the user to easily model complex multi-segment amplifier systems. It runs both on a workstation cluster at LLNL, and on the T3E Cray at CEA. We will discuss how we have reduce the required computation time without changing precision by optimizing the parameters which set the discretization level of the calculation. As an example, the sample of calculation points is chosen to fit the pumping profile through the thickness of amplifier slabs. We will show the difference in pump rates with our latest model as opposed to those produced by our earlier 2.5D code AmpModel. We will also present the results of calculations which model surfaces and other 3D effects such as top and bottom refelcotr positions and reflectivity which could not be included in the 2.5D model. This new computer model also includes a full 3D calculation of the amplified spontaneous emission rate in the laser slab, as opposed to the 2.5D model which tracked only the variation in the gain across the transverse dimensions of the slab. We will present the impact of this evolution of the model on the predicted stimulated decay rate and the resulting gain distribution. Comparison with most recent AmpLab experimental result will be presented, in the different typical NIF and LMJ configurations.

Reduced-gravity Environment Hardware Demonstrations of a Prototype Miniaturized Flow Cytometer and Companion Microfluidic Mixing Technology

PubMed Central

Bae, Candice; Sharpe, Julia Z.; Bishara, Andrew M.; Nelson, Emily S.; Weaver, Aaron S.; Brown, Daniel; McKay, Terri L.; Griffin, DeVon; Chan, Eugene Y.

2014-01-01

Until recently, astronaut blood samples were collected in-flight, transported to earth on the Space Shuttle, and analyzed in terrestrial laboratories. If humans are to travel beyond low Earth orbit, a transition towards space-ready, point-of-care (POC) testing is required. Such testing needs to be comprehensive, easy to perform in a reduced-gravity environment, and unaffected by the stresses of launch and spaceflight. Countless POC devices have been developed to mimic laboratory scale counterparts, but most have narrow applications and few have demonstrable use in an in-flight, reduced-gravity environment. In fact, demonstrations of biomedical diagnostics in reduced gravity are limited altogether, making component choice and certain logistical challenges difficult to approach when seeking to test new technology. To help fill the void, we are presenting a modular method for the construction and operation of a prototype blood diagnostic device and its associated parabolic flight test rig that meet the standards for flight-testing onboard a parabolic flight, reduced-gravity aircraft. The method first focuses on rig assembly for in-flight, reduced-gravity testing of a flow cytometer and a companion microfluidic mixing chip. Components are adaptable to other designs and some custom components, such as a microvolume sample loader and the micromixer may be of particular interest. The method then shifts focus to flight preparation, by offering guidelines and suggestions to prepare for a successful flight test with regard to user training, development of a standard operating procedure (SOP), and other issues. Finally, in-flight experimental procedures specific to our demonstrations are described. PMID:25490614

A Comparison of Two Designs of Postoperative Shoe on Function, Satisfaction, and Back Pain After Hallux Valgus Surgery.

PubMed

Patel, Shelain; Garg, Parag; Fazal, M Ali; Shahid, Muhammad S; Park, Derek H; Ray, Pinak S

2018-06-01

The reverse camber shoe is commonly used after hallux valgus corrective surgery to offload the forefoot but is associated with back pain and poor compliance. Recent designs of postoperative shoes may obviate the need for a reverse camber. The purpose of this study was to compare the effects of a reverse camber shoe and a noncambered shoe with transitional rigidity after hallux valgus correction. A cohort of 80 feet was prospectively studied undergoing surgery at a single NHS trust. The first 40 feet received the reverse cambered Jura Medical Off-loader Heel shoe and the subsequent 40 feet received the noncambered DonJoy Podalux shoe. No demographic differences existed between the groups and data were collected at 2 weeks, 6 weeks, and 6 months. The Manchester-Oxford Foot Questionnaire (MOXFQ), a 5-question survey and dichotomous question about back pain was used to assess clinical outcome and radiographs were reviewed by 2 orthopaedic surgeons to monitor for loss of correction. Both groups experienced comparable improvements in MOXFQ and shoe satisfaction from 2 weeks compared with 6 weeks. Six patients experienced back pain in the reverse cambered shoe group and none in the noncambered shoe group. Five patients stopped using the reverse cambered shoe during the first 6 weeks after surgery and none stopped using their prescribed noncambered shoe. No loss of corrections were observed in either group. Both shoe designs gave equal foot specific functional and radiological outcomes, but the noncambered shoe with transitional rigidity was associated with less back pain and better compliance. Level II: Prospective comparative study.

Enabling innovative research by supporting the life cycle of high frequency streaming sensor data in the Global Lake Ecological Observatory Network (GLEON)

NASA Astrophysics Data System (ADS)

Gries, C.; Read, J. S.; Winslow, L. A.; Hanson, P. C.; Weathers, K. C.

2014-12-01

The Global Lake Ecological Observatory Network (GLEON) is an international community of scientists, educators and citizens with the mission to conduct innovative science by sharing and interpreting high-resolution sensor data to understand, predict and communicate the role and response of lakes in a changing global environment. During its almost ten years of existence and continual growth, GLEON has inspired innovative science, new modeling approaches, and accumulated extensive experience in the management of streaming, high resolution, and large volume data. However, a recent 'data task force' identified inhibiting data infrastructure issues, including providing access to data, discovering distributed data, and integrating data into useful data products for scientific research and management. Accordingly, in support of the complete data lifecycle, tools are being developed by the GLEON community and integrated with innovative technology from other groups to improve environmental observations data management in the broader community. Specifically we will discuss raw data handling with tools developed by the Consortium of Universities for the Advancement of Hydrologic Sciences (CUAHSI, Observation Data Model and DataLoader), quality control practices using a newly developed R package (sensorQC), data access with HydroDesktop, or webservices delivering WaterML, data analysis with the R package rLakeAnalyzer, and final storage of the quality controlled, harmonized and value added data product in a DataONE member node. Such data product is then discoverable, accessible for new analyses and citable in subsequent publications. Leveraging GLEON's organizational structure, community trust, extensive experience, and technological talent the goal is to develop a design and implementation plan for a data publishing and sharing system that will address not only GLEON's needs, but also those of other environmental research communities.

Estimation of quantitative levels of diesel exhaust exposure and the health impact in the contemporary Australian mining industry.

PubMed

Peters, Susan; de Klerk, Nicholas; Reid, Alison; Fritschi, Lin; Musk, Aw Bill; Vermeulen, Roel

2017-03-01

To estimate quantitative levels of exposure to diesel exhaust expressed by elemental carbon (EC) in the contemporary mining industry and to describe the excess risk of lung cancer that may result from those levels. EC exposure has been monitored in Western Australian miners since 2003. Mixed-effects models were used to estimate EC levels for five surface and five underground occupation groups (as a fixed effect) and specific jobs within each group (as a random effect). Further fixed effects included sampling year and duration, and mineral mined. On the basis of published risk functions, we estimated excess lifetime risk of lung cancer mortality for several employment scenarios. Personal EC measurements (n=8614) were available for 146 different jobs at 124 mine sites. The mean estimated EC exposure level for surface occupations in 2011 was 14 µg/m 3 for 12 hour shifts. Levels for underground occupation groups ranged from 18 to 44 µg/m 3 . Underground diesel loader operators had the highest exposed specific job: 59 µg/m 3 . A lifetime career (45 years) as a surface worker or underground miner, experiencing exposure levels as estimated for 2011 (14 and 44 µg/m 3 EC), was associated with 5.5 and 38 extra lung cancer deaths per 1000 males, respectively. EC exposure levels in the contemporary Australian mining industry are still substantial, particularly for underground workers. The estimated excess numbers of lung cancer deaths associated with these exposures support the need for implementation of stringent occupational exposure limits for diesel exhaust. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Anion exchanger 2 is critical for CD8(+) T cells to maintain pHi homeostasis and modulate immune responses.

PubMed

Concepcion, Axel R; Salas, January T; Sarvide, Sarai; Sáez, Elena; Ferrer, Alex; López, María; Portu, Ainhoa; Banales, Jesús M; Hervás-Stubbs, Sandra; Oude Elferink, Ronald P J; Prieto, Jesús; Medina, Juan F

2014-05-01

Mitogenic stimulation of lymphocytes involves alkalinization of intracellular pH (pHi ). Subsequent pHi regulation may involve HCO3 (-) extrusion through Cl(-) /HCO3 (-) exchangers and/or Na(+) -HCO3 (-) co-transporters with acid-loading capability. Abnormalities in these mechanisms could result in immune dysfunctions, as suggested by the CD8(+) T-cell expansion encountered in mice lacking Ae2 (a widely expressed acid loader with electroneutral and Na(+) -independent Cl(-) /HCO3 (-) anion-exchange activity). Here we report that CD8(+) T cells but not CD4(+) T cells or other lymphocyte populations, are crucially dependent on Ae2 for pHi regulation. While total lymphocytes (including isolated CD4(+) T cells) exhibit Ae1 expression and Na(+) -HCO3 (-) co-transport with acidifying potential, CD8(+) T cells lack these acid-loading mechanisms. In Ae2-KO mice, CD4(+) but not CD8(+) T cells upregulate these potential Ae2 surrogates. As a consequence, Ae2-KO CD8(+) T cells exhibit alkalinized pHi , and dramatically increase their pHi upon CD3 stimulation. Moreover, stimulated Ae2-deficient CD8(+) T cells show enhanced intracellular production of IL-2 and membrane expression of its receptor IL-2Rα, together with increased cell proliferation and activation. These findings demonstrate that CD8(+) T cells are critically dependent on Ae2 for pHi homeostasis and tuning of cell proliferation and activation. Ae2 thus constitutes a novel target to modulate CD8(+) T-cell responses. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Crusader solid propellant best technical approach

DOE Office of Scientific and Technical Information (OSTI.GOV)

Graves, V.; Bader, G.; Dolecki, M.

1995-12-01

The goal of the Solid Propellant Resupply Team is to develop Crusader system concepts capable of automatically handling 155mm projectiles and Modular Artillery Charges (MACs) based on system requirements. The system encompasses all aspects of handling from initial input into a resupply vehicle (RSV) to the final loading into the breech of the self-propelled howitzer (SPH). The team, comprised of persons from military and other government organizations, developed concepts for the overall vehicles as well as their interior handling components. An intermediate review was conducted on those components, and revised concepts were completed in May 1995. A concept evaluation wasmore » conducted on the finalized concepts, from both a systems level and a component level. The team`s Best Technical Approach (BTA) concept was selected from that evaluation. Both vehicles in the BTA have a front-engine configuration with the crew situated behind the engine-low in the vehicles. The SPH concept utilizes an automated reload port at the rear of the vehicle, centered high. The RSV transfer boom will dock with this port to allow automated ammunition transfer. The SPH rearm system utilizes fully redundant dual loaders. Active magazines are used for both projectiles and MACs. The SPH also uses a nonconventional tilted ring turret configuration to maximize the available interior volume in the vehicle. This configuration can be rearmed at any elevation angle but only at 0{degree} azimuth. The RSV configuration is similar to that of the SPH. The RSV utilizes passive storage racks with a pick-and-place manipulator for handling the projectiles and active magazines for the MACs. A telescoping transfer boom extends out the front of the vehicle over the crew and engine.« less

Aerosol Sampling System for Collection of Capstone Depleted Uranium Particles in a High-Energy Environment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holmes, Thomas D.; Guilmette, Raymond A.; Cheng, Yung-Sung

2009-03-01

The Capstone Depleted Uranium Aerosol Study was undertaken to obtain aerosol samples resulting from a kinetic-energy cartridge with a large-caliber depleted uranium (DU) penetrator striking an Abrams or Bradley test vehicle. The sampling strategy was designed to (1) optimize the performance of the samplers and maintain their integrity in the extreme environment created during perforation of an armored vehicle by a DU penetrator, (2) collect aerosols as a function of time post-impact, and (3) obtain size-classified samples for analysis of chemical composition, particle morphology, and solubility in lung fluid. This paper describes the experimental setup and sampling methodologies used tomore » achieve these objectives. Custom-designed arrays of sampling heads were secured to the inside of the target in locations approximating the breathing zones of the vehicle commander, loader, gunner, and driver. Each array was designed to support nine filter cassettes and nine cascade impactors mounted with quick-disconnect fittings. Shielding and sampler placement strategies were used to minimize sampler loss caused by the penetrator impact and the resulting fragments of eroded penetrator and perforated armor. A cyclone train was used to collect larger quantities of DU aerosol for chemical composition and solubility. A moving filter sample was used to obtain semicontinuous samples for depleted uranium concentration determination. Control for the air samplers was provided by five remotely located valve control and pressure monitoring units located inside and around the test vehicle. These units were connected to a computer interface chassis and controlled using a customized LabVIEW engineering computer control program. The aerosol sampling arrays and control systems for the Capstone study provided the needed aerosol samples for physicochemical analysis, and the resultant data were used for risk assessment of exposure to DU aerosol.« less

Regulators of Slc4 bicarbonate transporter activity

PubMed Central

Thornell, Ian M.; Bevensee, Mark O.

2015-01-01

The Slc4 family of transporters is comprised of anion exchangers (AE1-4), Na+-coupled bicarbonate transporters (NCBTs) including electrogenic Na/bicarbonate cotransporters (NBCe1 and NBCe2), electroneutral Na/bicarbonate cotransporters (NBCn1 and NBCn2), and the electroneutral Na-driven Cl-bicarbonate exchanger (NDCBE), as well as a borate transporter (BTR1). These transporters regulate intracellular pH (pHi) and contribute to steady-state pHi, but are also involved in other physiological processes including CO2 carriage by red blood cells and solute secretion/reabsorption across epithelia. Acid-base transporters function as either acid extruders or acid loaders, with the Slc4 proteins moving HCO−3 either into or out of cells. According to results from both molecular and functional studies, multiple Slc4 proteins and/or associated splice variants with similar expected effects on pHi are often found in the same tissue or cell. Such apparent redundancy is likely to be physiologically important. In addition to regulating pHi, a HCO−3 transporter contributes to a cell's ability to fine tune the intracellular regulation of the cotransported/exchanged ion(s) (e.g., Na+ or Cl−). In addition, functionally similar transporters or splice variants with different regulatory profiles will optimize pH physiology and solute transport under various conditions or within subcellular domains. Such optimization will depend on activated signaling pathways and transporter expression profiles. In this review, we will summarize and discuss both well-known and more recently identified regulators of the Slc4 proteins. Some of these regulators include traditional second messengers, lipids, binding proteins, autoregulatory domains, and less conventional regulators. The material presented will provide insight into the diversity and physiological significance of multiple members within the Slc4 gene family. PMID:26124722

Regulators of Slc4 bicarbonate transporter activity.

PubMed

Thornell, Ian M; Bevensee, Mark O

2015-01-01

The Slc4 family of transporters is comprised of anion exchangers (AE1-4), Na(+)-coupled bicarbonate transporters (NCBTs) including electrogenic Na/bicarbonate cotransporters (NBCe1 and NBCe2), electroneutral Na/bicarbonate cotransporters (NBCn1 and NBCn2), and the electroneutral Na-driven Cl-bicarbonate exchanger (NDCBE), as well as a borate transporter (BTR1). These transporters regulate intracellular pH (pHi) and contribute to steady-state pHi, but are also involved in other physiological processes including CO2 carriage by red blood cells and solute secretion/reabsorption across epithelia. Acid-base transporters function as either acid extruders or acid loaders, with the Slc4 proteins moving HCO(-) 3 either into or out of cells. According to results from both molecular and functional studies, multiple Slc4 proteins and/or associated splice variants with similar expected effects on pHi are often found in the same tissue or cell. Such apparent redundancy is likely to be physiologically important. In addition to regulating pHi, a HCO(-) 3 transporter contributes to a cell's ability to fine tune the intracellular regulation of the cotransported/exchanged ion(s) (e.g., Na(+) or Cl(-)). In addition, functionally similar transporters or splice variants with different regulatory profiles will optimize pH physiology and solute transport under various conditions or within subcellular domains. Such optimization will depend on activated signaling pathways and transporter expression profiles. In this review, we will summarize and discuss both well-known and more recently identified regulators of the Slc4 proteins. Some of these regulators include traditional second messengers, lipids, binding proteins, autoregulatory domains, and less conventional regulators. The material presented will provide insight into the diversity and physiological significance of multiple members within the Slc4 gene family.

Accessing and distributing EMBL data using CORBA (common object request broker architecture).

PubMed

Wang, L; Rodriguez-Tomé, P; Redaschi, N; McNeil, P; Robinson, A; Lijnzaad, P

2000-01-01

The EMBL Nucleotide Sequence Database is a comprehensive database of DNA and RNA sequences and related information traditionally made available in flat-file format. Queries through tools such as SRS (Sequence Retrieval System) also return data in flat-file format. Flat files have a number of shortcomings, however, and the resources therefore currently lack a flexible environment to meet individual researchers' needs. The Object Management Group's common object request broker architecture (CORBA) is an industry standard that provides platform-independent programming interfaces and models for portable distributed object-oriented computing applications. Its independence from programming languages, computing platforms and network protocols makes it attractive for developing new applications for querying and distributing biological data. A CORBA infrastructure developed by EMBL-EBI provides an efficient means of accessing and distributing EMBL data. The EMBL object model is defined such that it provides a basis for specifying interfaces in interface definition language (IDL) and thus for developing the CORBA servers. The mapping from the object model to the relational schema in the underlying Oracle database uses the facilities provided by PersistenceTM, an object/relational tool. The techniques of developing loaders and 'live object caching' with persistent objects achieve a smart live object cache where objects are created on demand. The objects are managed by an evictor pattern mechanism. The CORBA interfaces to the EMBL database address some of the problems of traditional flat-file formats and provide an efficient means for accessing and distributing EMBL data. CORBA also provides a flexible environment for users to develop their applications by building clients to our CORBA servers, which can be integrated into existing systems.

FPGA wavelet processor design using language for instruction-set architectures (LISA)

NASA Astrophysics Data System (ADS)

Meyer-Bäse, Uwe; Vera, Alonzo; Rao, Suhasini; Lenk, Karl; Pattichis, Marios

2007-04-01

The design of an microprocessor is a long, tedious, and error-prone task consisting of typically three design phases: architecture exploration, software design (assembler, linker, loader, profiler), architecture implementation (RTL generation for FPGA or cell-based ASIC) and verification. The Language for instruction-set architectures (LISA) allows to model a microprocessor not only from instruction-set but also from architecture description including pipelining behavior that allows a design and development tool consistency over all levels of the design. To explore the capability of the LISA processor design platform a.k.a. CoWare Processor Designer we present in this paper three microprocessor designs that implement a 8/8 wavelet transform processor that is typically used in today's FBI fingerprint compression scheme. We have designed a 3 stage pipelined 16 bit RISC processor (NanoBlaze). Although RISC μPs are usually considered "fast" processors due to design concept like constant instruction word size, deep pipelines and many general purpose registers, it turns out that DSP operations consume essential processing time in a RISC processor. In a second step we have used design principles from programmable digital signal processor (PDSP) to improve the throughput of the DWT processor. A multiply-accumulate operation along with indirect addressing operation were the key to achieve higher throughput. A further improvement is possible with today's FPGA technology. Today's FPGAs offer a large number of embedded array multipliers and it is now feasible to design a "true" vector processor (TVP). A multiplication of two vectors can be done in just one clock cycle with our TVP, a complete scalar product in two clock cycles. Code profiling and Xilinx FPGA ISE synthesis results are provided that demonstrate the essential improvement that a TVP has compared with traditional RISC or PDSP designs.

Characterization, localization, and seasonal changes of the sucrose transporter FeSUT1 in the phloem of Fraxinus excelsior

PubMed Central

Öner-Sieben, Soner; Rappl, Christine; Sauer, Norbert; Stadler, Ruth; Lohaus, Gertrud

2015-01-01

Trees are generally assumed to be symplastic phloem loaders. A typical feature for most wooden species is an open minor vein structure with symplastic connections between mesophyll cells and phloem cells, which allow sucrose to move cell-to-cell through the plasmodesmata into the phloem. Fraxinus excelsior (Oleaceae) also translocates raffinose family oligosaccharides in addition to sucrose. Sucrose concentration was recently shown to be higher in the phloem sap than in the mesophyll cells. This suggests the involvement of apoplastic steps and the activity of sucrose transporters in addition to symplastic phloem-loading processes. In this study, the sucrose transporter FeSUT1 from F. excelsior was analysed. Heterologous expression in baker’s yeast showed that FeSUT1 mediates the uptake of sucrose. Immunohistochemical analyses revealed that FeSUT1 was exclusively located in phloem cells of minor veins and in the transport phloem of F. excelsior. Further characterization identified these cells as sieve elements and possibly ordinary companion cells but not as intermediary cells. The localization and expression pattern point towards functions of FeSUT1 in phloem loading of sucrose as well as in sucrose retrieval. FeSUT1 is most likely responsible for the observed sucrose gradient between mesophyll and phloem. The elevated expression level of FeSUT1 indicated an increased apoplastic carbon export activity from the leaves during spring and late autumn. It is hypothesized that the importance of apoplastic loading is high under low-sucrose conditions and that the availability of two different phloem-loading mechanisms confers advantages for temperate woody species like F. excelsior. PMID:26022258

Structural and mechanistic insights into Mcm2-7 double-hexamer assembly and function

DOE PAGES

Sun, Jingchuan; Li, Huilin; Fernandez-Cid, Alejandra; ...

2014-10-15

Eukaryotic cells license each DNA replication origin during G1 phase by assembling a prereplication complex that contains a Mcm2–7 (minichromosome maintenance proteins 2–7) double hexamer. During S phase, each Mcm2–7 hexamer forms the core of a replicative DNA helicase. However, the mechanisms of origin licensing and helicase activation are poorly understood. The helicase loaders ORC–Cdc6 function to recruit a single Cdt1–Mcm2–7 heptamer to replication origins prior to Cdt1 release and ORC–Cdc6–Mcm2–7 complex formation, but how the second Mcm2–7 hexamer is recruited to promote double-hexamer formation is not well understood. Here, structural evidence for intermediates consisting of an ORC–Cdc6–Mcm2–7 complex andmore » an ORC–Cdc6–Mcm2–7–Mcm2–7 complex are reported, which together provide new insights into DNA licensing. Detailed structural analysis of the loaded Mcm2–7 double-hexamer complex demonstrates that the two hexamers are interlocked and misaligned along the DNA axis and lack ATP hydrolysis activity that is essential for DNA helicase activity. Moreover, we show that the head-to-head juxtaposition of the Mcm2–7 double hexamer generates a new protein interaction surface that creates a multisubunit-binding site for an S-phase protein kinase that is known to activate DNA replication. The data suggest how the double hexamer is assembled and how helicase activity is regulated during DNA licensing, with implications for cell cycle control of DNA replication and genome stability.« less

Convergence at the faces of development workings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borisenko, A.A.

1977-07-01

Since 1963 we have been carrying out investigations in pits of the Pechora coalfield to establish the general laws of roof-floor convergence in the face areas of development workings and their role in gas bursts. We also considered how various methods of working on the seam influence the amount of type of convergence. The observations were made in 20 workings in five pits of Vorkutaugol Group, cut by cutter-loaders and by drilling and blasting at depths between 350 and 600 m; the cross-sectional areas of the workings ranged frm 3.7 to 12.0 m/sup 2/. The aggregated data on daily convergencemore » values was analyzed by the multiple correlation method with the aid of a computer. The aim of the analysis was to elucidate the influence of six factors on the daily convergence values: the depth below the surface, the corrected seam strength, the cross-sectional area of the working, the initial distance from the face to the measurement prop, the daily advance, and the thickness of the seam. The combined correlation coefficient was rather low - 0.49 with a reliability of 9.13. The greatest influence on the convergence values is exerted by the cross-sectional area and by the distance from the face (the partial correlation coefficients being 0.281 and 0.310, respectively), and lesser influences are exerted by the depth below the surface and by the corrected strength of the seam (partial correlationcoefficients 0.164 and 0.178); the influences of seam thickness and daily face advance are very slight. The multiple correlation results indicate that a very great influence is exerted by disregarded factors, among which the most important are undoubtedly the properties of the surrounding rocks.« less

Single-molecule visualization of Saccharomyces cerevisiae leading-strand synthesis reveals dynamic interaction between MTC and the replisome

PubMed Central

Lewis, Jacob S.; Spenkelink, Lisanne M.; Schauer, Grant D.; Hill, Flynn R.; Georgescu, Roxanna E.; O’Donnell, Michael E.; van Oijen, Antoine M.

2017-01-01

The replisome, the multiprotein system responsible for genome duplication, is a highly dynamic complex displaying a large number of different enzyme activities. Recently, the Saccharomyces cerevisiae minimal replication reaction has been successfully reconstituted in vitro. This provided an opportunity to uncover the enzymatic activities of many of the components in a eukaryotic system. Their dynamic behavior and interactions in the context of the replisome, however, remain unclear. We use a tethered-bead assay to provide real-time visualization of leading-strand synthesis by the S. cerevisiae replisome at the single-molecule level. The minimal reconstituted leading-strand replisome requires 24 proteins, forming the CMG helicase, the Pol ε DNA polymerase, the RFC clamp loader, the PCNA sliding clamp, and the RPA single-stranded DNA binding protein. We observe rates and product lengths similar to those obtained from ensemble biochemical experiments. At the single-molecule level, we probe the behavior of two components of the replication progression complex and characterize their interaction with active leading-strand replisomes. The Minichromosome maintenance protein 10 (Mcm10), an important player in CMG activation, increases the number of productive replication events in our assay. Furthermore, we show that the fork protection complex Mrc1–Tof1–Csm3 (MTC) enhances the rate of the leading-strand replisome threefold. The introduction of periods of fast replication by MTC leads to an average rate enhancement of a factor of 2, similar to observations in cellular studies. We observe that the MTC complex acts in a dynamic fashion with the moving replisome, leading to alternating phases of slow and fast replication. PMID:28923950

Evaluating health risks from occupational exposure to pesticides and the regulatory response.

PubMed Central

Woodruff, T J; Kyle, A D; Bois, F Y

1994-01-01

In this study, we used measurements of occupational exposures to pesticides in agriculture to evaluate health risks and analyzed how the federal regulatory program is addressing these risks. Dose estimates developed by the State of California from measured occupational exposures to 41 pesticides were compared to standard indices of acute toxicity (LD50) and chronic effects (reference dose). Lifetime cancer risks were estimated using cancer potencies. Estimated absorbed daily doses for mixers, loaders, and applicators of pesticides ranged from less than 0.0001% to 48% of the estimated human LD50 values, and doses for 10 of 40 pesticides exceeded 1% of the estimated human LD50 values. Estimated lifetime absorbed daily doses ranged from 0.1% to 114,000% of the reference doses developed by the U.S. Environmental Protection Agency, and doses for 13 of 25 pesticides were above them. Lifetime cancer risks ranged from 1 per million to 1700 per million, and estimates for 12 of 13 pesticides were above 1 per million. Similar results were obtained for field workers and flaggers. For the pesticides examined, exposures pose greater risks of chronic effects than acute effects. Exposure reduction measures, including use of closed mixing systems and personal protective equipment, significantly reduced exposures. Proposed regulations rely primarily on requirements for personal protective equipment and use restrictions to protect workers. Chronic health risks are not considered in setting these requirements. Reviews of pesticides by the federal pesticide regulatory program have had little effect on occupational risks. Policy strategies that offer immediate protection for workers and that are not dependent on extensive review of individual pesticides should be pursued. Images Figure 1. PMID:7713022

A Prototype Bucket Wheel Excavator for the Moon, Mars and Phobos

NASA Astrophysics Data System (ADS)

Muff, T.; Johnson, L.; King, R.; Duke, M. B.

2004-02-01

Excavation of surface regolith material is the first step in processes to extract volatile materials from planetary surface regolith for the production of propellant and life support consumables. Typically, concentrations of volatiles are low, so relatively large amounts of material must be excavated. A bucket wheel excavator is proposed, which has the capability of continuous excavation, which is readily adapted to granular regolith materials as found on the Moon, in drift deposits on Mars, and probably on the surface of asteroids and satellites, such as Phobos. The bucket wheel excavator is relatively simple, compared to machines such as front end loaders. It also has the advantage that excavation forces are principally horizontal rather than vertical, which minimizes the need for excavator mass and suits it to operations in reduced gravity fields. A prototype small bucket wheel excavator has been built at approximately the scale of the rovers that are carried to Mars on the Mars Exploration Rover Mission. The prototype allows the collection of data on forces exerted and power requirements for excavation and will provide data on which more efficient designs can be based. At excavation rates in the vicinity of one rover mass of material excavated per hour, tests of the prototype demonstrate that the power required is largely that needed to operate the excavator hardware and not related strongly to the amount of material excavated. This suggests that the excavation rate can be much larger for the same excavation system mass. Work on this prototype is continuing on the details of transfer of material from the bucket wheel to an internal conveyor mechanism, which testing demonstrated to be problematic in the current design.

Accessing and distributing EMBL data using CORBA (common object request broker architecture)

PubMed Central

Wang, Lichun; Rodriguez-Tomé, Patricia; Redaschi, Nicole; McNeil, Phil; Robinson, Alan; Lijnzaad, Philip

2000-01-01

Background: The EMBL Nucleotide Sequence Database is a comprehensive database of DNA and RNA sequences and related information traditionally made available in flat-file format. Queries through tools such as SRS (Sequence Retrieval System) also return data in flat-file format. Flat files have a number of shortcomings, however, and the resources therefore currently lack a flexible environment to meet individual researchers' needs. The Object Management Group's common object request broker architecture (CORBA) is an industry standard that provides platform-independent programming interfaces and models for portable distributed object-oriented computing applications. Its independence from programming languages, computing platforms and network protocols makes it attractive for developing new applications for querying and distributing biological data. Results: A CORBA infrastructure developed by EMBL-EBI provides an efficient means of accessing and distributing EMBL data. The EMBL object model is defined such that it provides a basis for specifying interfaces in interface definition language (IDL) and thus for developing the CORBA servers. The mapping from the object model to the relational schema in the underlying Oracle database uses the facilities provided by PersistenceTM, an object/relational tool. The techniques of developing loaders and 'live object caching' with persistent objects achieve a smart live object cache where objects are created on demand. The objects are managed by an evictor pattern mechanism. Conclusions: The CORBA interfaces to the EMBL database address some of the problems of traditional flat-file formats and provide an efficient means for accessing and distributing EMBL data. CORBA also provides a flexible environment for users to develop their applications by building clients to our CORBA servers, which can be integrated into existing systems. PMID:11178259

Case Study of the Space Shuttle Cockpit Avionics Upgrade Software

NASA Technical Reports Server (NTRS)

Ferguson, Roscoe C.; Thompson, Hiram C.

2005-01-01

The purpose of the Space Shuttle Cockpit Avionics Upgrade project was to reduce crew workload and improve situational awareness. The upgrade was to augment the Shuttle avionics system with new hardware and software. An early version of this system was used to gather human factor statistics in the Space Shuttle Motion Simulator of the Johnson Space Center for one month by multiple teams of astronauts. The results were compiled by NASA Ames Research Center and it was was determined that the system provided a better than expected increase in situational awareness and reduction in crew workload. Even with all of the benefits nf the system, NASA cancelled the project towards the end of the development cycle. A major success of this project was the validation of the hardware architecture and software design. This was significant because the project incorporated new technology and approaches for the development of human rated space software. This paper serves as a case study to document knowledge gained and techniques that can be applied for future space avionics development efforts. The major technological advances were the use of reflective memory concepts for data acquisition and the incorporation of Commercial off the Shelf (COTS) products in a human rated space avionics system. The infused COTS products included a real time operating system, a resident linker and loader, a display generation tool set, and a network data manager. Some of the successful design concepts were the engineering of identical outputs in multiple avionics boxes using an event driven approach and inter-computer communication, a reconfigurable data acquisition engine, the use of a dynamic bus bandwidth allocation algorithm. Other significant experiences captured were the use of prototyping to reduce risk, and the correct balance between Object Oriented and Functional based programming.

Characteristics of typical non-road machinery emissions in China by using portable emission measurement system.

PubMed

Fu, Mingliang; Ge, Yunshan; Tan, Jianwei; Zeng, Tao; Liang, Bin

2012-10-15

Non-road machinery, especially construction equipment could be an important pollutant source of the deterioration in air quality in Chinese urban areas due to its large quantity and to the absence of stringent emission requirements. In this study, emission tests were performed on 12 excavators and 8 wheel loaders by using portable emission measurement system (PEMS) to determine their emission characteristics. The typical operating modes were categorized as idling mode, moving mode and working mode. Compared with those during idling and moving modes, the average time-based emission factors during working mode of HC were 2.61 and 1.27 times higher, NO(x) were 3.66 and 1.36 times higher, and PM were 4.05 and 1.95 times higher, respectively. Under all conditions, categories of the measured emissions increased with the rise in engine power. Compared with those of Stage I emission standard equipment, gaseous emissions and PM emitted from Stage II emission standard equipment were lower. The results indicated that, from Stage I to Stage II, the average reductions of HC, NO(x) and PM were 56%, 37% and 29% for the working mode, respectively. Those results also demonstrated the effectiveness of emission control regulation and the improvement of emission control technology. The data and tests show that the longer the accumulated working hours, the higher HC and NO(x) average fuel-based emission factors are. The emissions measured from the construction vehicles employed in this study were higher than the data collected in previous studies, which shows that it is critical for the government to put into effect more stringent emission regulations to further improve the air quality in Chinese urban areas. Copyright © 2012 Elsevier B.V. All rights reserved.

Design, development, and validation of a segment support actuator for the prototype segmented mirror telescope

NASA Astrophysics Data System (ADS)

Deshmukh, Prasanna Gajanan; Mandal, Amaresh; Parihar, Padmakar S.; Nayak, Dayananda; Mishra, Deepta Sundar

2018-01-01

Segmented mirror telescopes (SMT) are built using several small hexagonal mirrors positioned and aligned by the three actuators and six edge sensors per segment to maintain the shape of the primary mirror. The actuators are responsible for maintaining and tracking the mirror segments to the desired position, in the presence of external disturbances introduced by wind, vibration, gravity, and temperature. The present paper describes our effort to develop a soft actuator and the actuator controller for prototype SMT at Indian Institute of Astrophysics, Bangalore. The actuator designed, developed, and validated is a soft actuator based on the voice coil motor and flexural elements. It is designed for the range of travel of ±1.5 mm and the force range of 25 N along with an offloading mechanism to reduce the power consumption. A precision controller using a programmable system on chip (PSoC 5Lp) and a customized drive board has also been developed for this actuator. The close loop proportional-integral-derivative (PID) controller implemented in the PSoC gets position feedback from a high-resolution linear optical encoder. The optimum PID gains are derived using relay tuning method. In the laboratory, we have conducted several experiments to test the performance of the prototype soft actuator as well as the controller. We could achieve 5.73- and 10.15-nm RMS position errors in the steady state as well as tracking with a constant speed of 350 nm/s, respectively. We also present the outcome of various performance tests carried out when off-loader is in action as well as the actuator is subjected to dynamic wind loading.

Simulating Negative Pickup Ions and Ion Cyclotron Wave Generation at Europa (Invited)

NASA Astrophysics Data System (ADS)

Desai, R. T.; Cowee, M.; Gary, S. P.; Wei, H.; Coates, A. J.; Kataria, D. O.; Fu, X.

2015-12-01

The mass loading of space environments through the ionisation of planetary atmospheres is a fundamental process governing the plasma interactions and long term evolution of celestial bodies across the solar system. Regions containing significant pickup ion populations have been observed to exhibit a rich variety of electromagnetic plasma wave phenomena, the characteristics and properties of which can be used to infer the ion species present, their spatial and temporal distributions, and the global ionisation rates of the neutral material. In this study we present hybrid (kinetic ion, massless fluid electron) simulations of ion pickup and Ion Cyclotron (IC) waves observed in the Jovian magnetosphere and draw comparisons to sub-alfvénic pickup observed by Cassini in the Saturnian system, and also to supra-alfvénic pickup at planetary bodies immersed directly in the solar wind. At Jupiter, Europa has been identified as the secondary mass loader in the magnetosphere, orbiting within a neutral gas torus at ~9.38 Rj. Near Europa, Galileo magnetometer observations displayed bursty IC wave characteristics at the gyrofrequency of a number of species including SO2, K, Cl, O2, and Na, suggesting a complex mass loading environment. A particular deduction from the dataset was the presence of both positively and negatively charged pickup ions, inferred from the left and right hand polarisations of the transverse waves. Using hybrid simulations for both positively and negatively charged Cl pickup ions we are able to self-consistently reproduce the growth of both right and left hand near-circularly polarised waves in agreement with linear theory and, using the observed wave amplitudes, estimate Cl pickup ion densities at Europa.

Parental occupation and risk of small-for-gestational-age births: a nationwide epidemiological study in Sweden

PubMed Central

Li, X.; Sundquist, J.; Sundquist, K.

2010-01-01

BACKGROUND Although evidence suggests that some occupations may be a risk factor for small-for-gestational age (SGA) birth, associations between a wide range of maternal and paternal occupations and risk of SGA births remain unclear. Our objective was to analyze the risk of SGA births by parental occupation, including the entire Swedish population of mothers (≥20 years) and fathers. METHODS We linked nationwide data (1990–2004) on singletons born to employed mothers to nationwide data on maternal and paternal occupation and other individual-level variables. Information on parental occupations was obtained from the 1990 census. Approximately 95% of SGA births (calculated using normative data) were defined on the basis of ultrasound. Odds ratios of SGA birth were calculated with 95% confidence intervals. Women and men were analyzed separately. RESULTS There were 816 310 first singleton live births during the study period, of which 29 603 were SGA events. Families with low incomes had an increased risk of SGA births. After accounting for maternal age at the infant's birth, period of birth, family income, region of residence, marital status and smoking habits, several maternal occupational groups (including ‘mechanics and iron and metalware workers’ and ‘packers, loaders and warehouse workers’) had a significantly higher risk of SGA birth than the reference group (all women in the study population). Among paternal occupational groups, only waiters had an increased risk of SGA birth. CONCLUSIONS This large-scale follow-up study shows that maternal occupation affects risk of SGA birth, whereas paternal occupation does not seem to have an impact on SGA birth. Further studies are required to examine the specific agents in those maternal occupations that are associated with an increased risk of SGA birth. PMID:20133322

UNDERGROUND URANIUM MINING ON COLORADO PLATEAU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dare, W.L.

1958-10-31

The size and continuity of the Chinie ore bodies in the Big Indian district, Utah, have permitted mine operators in plan a more integrated development and mining system using larger and more specialized equipment. Thick ore and firm backs at the south end of the district than permitted room and pillar mining, using large drill jumbos send diesel-powered haulage equipment. The Gismo loader and draw-chute system has proved efficient. Driving the haulage- way below the stope level is an advantage when pillars are recovered. To the north, thinner ore with weaker backs favor retreat systems and smaller equipment. Here, themore » ore bodies are delineated by a grid system of drifts, send the ore recovered by panel, longwall, or similar mining methods, retreating toward the principal entry. Labor productivity ranges from 8 to 21 tons per man-shift, send direct mining send development costs, excluding initial development, ranges from 75 to 51 per ton. A unique system of mine development is in the Temple Mountain district, Utah, where the shallow Chinie deposits are mined through 36- inch diameter calyx drill holes. Using small diesel-powered ore buggies and bucket hoisting, ore in produced from the two largest mines at a rate of 4.1 tons per man-shift, at a direci cost of 15 a ton. Ambrosia Lake deposits range from 5 to 80 feet thick and occur from 350 to 1,000 feet below the surface. These mines are in development stages. Open, retreat, and top-slice sloping is planned. Adequate ventilation is essential in uranium mining since sufficient air must be coursed through the workings to maintain airborne radioactive concentration at tolerance levels send dilute exhaust gases where diesel-powered equipment is used. Uranium miners have found that radiometric scannning is a quick and efficient method for checking ths grade of the ore produced and in process of development. (auth)« less

Atlas - a data warehouse for integrative bioinformatics.

PubMed

Shah, Sohrab P; Huang, Yong; Xu, Tao; Yuen, Macaire M S; Ling, John; Ouellette, B F Francis

2005-02-21

We present a biological data warehouse called Atlas that locally stores and integrates biological sequences, molecular interactions, homology information, functional annotations of genes, and biological ontologies. The goal of the system is to provide data, as well as a software infrastructure for bioinformatics research and development. The Atlas system is based on relational data models that we developed for each of the source data types. Data stored within these relational models are managed through Structured Query Language (SQL) calls that are implemented in a set of Application Programming Interfaces (APIs). The APIs include three languages: C++, Java, and Perl. The methods in these API libraries are used to construct a set of loader applications, which parse and load the source datasets into the Atlas database, and a set of toolbox applications which facilitate data retrieval. Atlas stores and integrates local instances of GenBank, RefSeq, UniProt, Human Protein Reference Database (HPRD), Biomolecular Interaction Network Database (BIND), Database of Interacting Proteins (DIP), Molecular Interactions Database (MINT), IntAct, NCBI Taxonomy, Gene Ontology (GO), Online Mendelian Inheritance in Man (OMIM), LocusLink, Entrez Gene and HomoloGene. The retrieval APIs and toolbox applications are critical components that offer end-users flexible, easy, integrated access to this data. We present use cases that use Atlas to integrate these sources for genome annotation, inference of molecular interactions across species, and gene-disease associations. The Atlas biological data warehouse serves as data infrastructure for bioinformatics research and development. It forms the backbone of the research activities in our laboratory and facilitates the integration of disparate, heterogeneous biological sources of data enabling new scientific inferences. Atlas achieves integration of diverse data sets at two levels. First, Atlas stores data of similar types using common data models, enforcing the relationships between data types. Second, integration is achieved through a combination of APIs, ontology, and tools. The Atlas software is freely available under the GNU General Public License at: http://bioinformatics.ubc.ca/atlas/

Diffusion and bulk flow in phloem loading: A theoretical analysis of the polymer trap mechanism for sugar transport in plants

NASA Astrophysics Data System (ADS)

Dölger, Julia; Rademaker, Hanna; Liesche, Johannes; Schulz, Alexander; Bohr, Tomas

2014-10-01

Plants create sugar in the mesophyll cells of their leaves by photosynthesis. This sugar, mostly sucrose, has to be loaded via the bundle sheath into the phloem vascular system (the sieve elements), where it is distributed to growing parts of the plant. We analyze the feasibility of a particular loading mechanism, active symplasmic loading, also called the polymer trap mechanism, where sucrose is transformed into heavier sugars, such as raffinose and stachyose, in the intermediary-type companion cells bordering the sieve elements in the minor veins of the phloem. Keeping the heavier sugars from diffusing back requires that the plasmodesmata connecting the bundle sheath with the intermediary cell act as extremely precise filters, which are able to distinguish between molecules that differ by less than 20% in size. In our modeling, we take into account the coupled water and sugar movement across the relevant interfaces, without explicitly considering the chemical reactions transforming the sucrose into the heavier sugars. Based on the available data for plasmodesmata geometry, sugar concentrations, and flux rates, we conclude that this mechanism can in principle function, but that it requires pores of molecular sizes. Comparing with the somewhat uncertain experimental values for sugar export rates, we expect the pores to be only 5%-10% larger than the hydraulic radius of the sucrose molecules. We find that the water flow through the plasmodesmata, which has not been quantified before, contributes only 10%-20% to the sucrose flux into the intermediary cells, while the main part is transported by diffusion. On the other hand, the subsequent sugar translocation into the sieve elements would very likely be carried predominantly by bulk water flow through the plasmodesmata. Thus, in contrast to apoplasmic loaders, all the necessary water for phloem translocation would be supplied in this way with no need for additional water uptake across the plasma membranes of the phloem.

Spectacle and SpecViz: New Spectral Analysis and Visualization Tools

NASA Astrophysics Data System (ADS)

Earl, Nicholas; Peeples, Molly; JDADF Developers

2018-01-01

A new era of spectroscopic exploration of our universe is being ushered in with advances in instrumentation and next-generation space telescopes. The advent of new spectroscopic instruments has highlighted a pressing need for tools scientists can use to analyze and explore these new data. We have developed Spectacle, a software package for analyzing both synthetic spectra from hydrodynamic simulations as well as real COS data with an aim of characterizing the behavior of the circumgalactic medium. It allows easy reduction of spectral data and analytic line generation capabilities. Currently, the package is focused on automatic determination of absorption regions and line identification with custom line list support, simultaneous line fitting using Voigt profiles via least-squares or MCMC methods, and multi-component modeling of blended features. Non-parametric measurements, such as equivalent widths, delta v90, and full-width half-max are available. Spectacle also provides the ability to compose compound models used to generate synthetic spectra allowing the user to define various LSF kernels, uncertainties, and to specify sampling.We also present updates to the visualization tool SpecViz, developed in conjunction with the JWST data analysis tools development team, to aid in the exploration of spectral data. SpecViz is an open source, Python-based spectral 1-D interactive visualization and analysis application built around high-performance interactive plotting. It supports handling general and instrument-specific data and includes advanced tool-sets for filtering and detrending one-dimensional data, along with the ability to isolate absorption regions using slicing and manipulate spectral features via spectral arithmetic. Multi-component modeling is also possible using a flexible model fitting tool-set that supports custom models to be used with various fitting routines. It also features robust user extensions such as custom data loaders and support for user-created plugins that add new functionality.This work was supported in part by HST AR #13919, HST GO #14268, and HST AR #14560.

Diffusion and bulk flow in phloem loading: a theoretical analysis of the polymer trap mechanism for sugar transport in plants.

PubMed

Dölger, Julia; Rademaker, Hanna; Liesche, Johannes; Schulz, Alexander; Bohr, Tomas

2014-10-01

Plants create sugar in the mesophyll cells of their leaves by photosynthesis. This sugar, mostly sucrose, has to be loaded via the bundle sheath into the phloem vascular system (the sieve elements), where it is distributed to growing parts of the plant. We analyze the feasibility of a particular loading mechanism, active symplasmic loading, also called the polymer trap mechanism, where sucrose is transformed into heavier sugars, such as raffinose and stachyose, in the intermediary-type companion cells bordering the sieve elements in the minor veins of the phloem. Keeping the heavier sugars from diffusing back requires that the plasmodesmata connecting the bundle sheath with the intermediary cell act as extremely precise filters, which are able to distinguish between molecules that differ by less than 20% in size. In our modeling, we take into account the coupled water and sugar movement across the relevant interfaces, without explicitly considering the chemical reactions transforming the sucrose into the heavier sugars. Based on the available data for plasmodesmata geometry, sugar concentrations, and flux rates, we conclude that this mechanism can in principle function, but that it requires pores of molecular sizes. Comparing with the somewhat uncertain experimental values for sugar export rates, we expect the pores to be only 5%-10% larger than the hydraulic radius of the sucrose molecules. We find that the water flow through the plasmodesmata, which has not been quantified before, contributes only 10%-20% to the sucrose flux into the intermediary cells, while the main part is transported by diffusion. On the other hand, the subsequent sugar translocation into the sieve elements would very likely be carried predominantly by bulk water flow through the plasmodesmata. Thus, in contrast to apoplasmic loaders, all the necessary water for phloem translocation would be supplied in this way with no need for additional water uptake across the plasma membranes of the phloem.

Atlas – a data warehouse for integrative bioinformatics

PubMed Central

Shah, Sohrab P; Huang, Yong; Xu, Tao; Yuen, Macaire MS; Ling, John; Ouellette, BF Francis

2005-01-01

Background We present a biological data warehouse called Atlas that locally stores and integrates biological sequences, molecular interactions, homology information, functional annotations of genes, and biological ontologies. The goal of the system is to provide data, as well as a software infrastructure for bioinformatics research and development. Description The Atlas system is based on relational data models that we developed for each of the source data types. Data stored within these relational models are managed through Structured Query Language (SQL) calls that are implemented in a set of Application Programming Interfaces (APIs). The APIs include three languages: C++, Java, and Perl. The methods in these API libraries are used to construct a set of loader applications, which parse and load the source datasets into the Atlas database, and a set of toolbox applications which facilitate data retrieval. Atlas stores and integrates local instances of GenBank, RefSeq, UniProt, Human Protein Reference Database (HPRD), Biomolecular Interaction Network Database (BIND), Database of Interacting Proteins (DIP), Molecular Interactions Database (MINT), IntAct, NCBI Taxonomy, Gene Ontology (GO), Online Mendelian Inheritance in Man (OMIM), LocusLink, Entrez Gene and HomoloGene. The retrieval APIs and toolbox applications are critical components that offer end-users flexible, easy, integrated access to this data. We present use cases that use Atlas to integrate these sources for genome annotation, inference of molecular interactions across species, and gene-disease associations. Conclusion The Atlas biological data warehouse serves as data infrastructure for bioinformatics research and development. It forms the backbone of the research activities in our laboratory and facilitates the integration of disparate, heterogeneous biological sources of data enabling new scientific inferences. Atlas achieves integration of diverse data sets at two levels. First, Atlas stores data of similar types using common data models, enforcing the relationships between data types. Second, integration is achieved through a combination of APIs, ontology, and tools. The Atlas software is freely available under the GNU General Public License at: PMID:15723693

'Shrink' losses in commercially sized corn silage piles: Quantifying total losses and where they occur.

PubMed

Robinson, P H; Swanepoel, N; Heguy, J M; Price, T; Meyer, D M

2016-01-15

Silage 'shrink' (i.e., loss of fresh chopped crop between ensiling and feedout) represents a nutrient loss which can degrade air quality as volatile carbon compounds, degrade surface waterways due to seepage, or degrade aquifers due to seepage. Virtually no research has documented shrink in large silage piles. The term 'shrink' is often ill defined, but can be expressed as losses of wet weight (WW), oven dry matter (oDM), and oDM corrected for volatiles lost in the drying oven (vcoDM). Corn silage piles (4 wedge, 2 rollover/wedge, 1 bunker) from 950 to 12,204 tonnes as built, on concrete (4), soil (2) and a combination (1) in California's San Joaquin Valley, using a bacterial inoculant, covered within 24 h with an oxygen barrier inner film and black/white outer plastic, fed out using large front end loaders through an electronic feed tracking system, and from the 2013 crop year, were used. Shrink as WW, oDM and vcoDM were 90±17, 68±18 and 28±21 g/kg, suggesting that much WW shrink is water and much oDM shrink is volatiles lost during analytical oven drying. Most shrink occurred in the silage mass with losses from exposed silage faces, as well as between exposed face silage removal and the total mixed ration mixer, being low. Silage bulk density, exposed silage face management and face use rate did not have obvious impacts on any shrink measure, but age of the silage pile during silage feedout impacted shrink losses ('older' silage piles being higher), but most strongly for WW shrink. Real shrink losses (i.e., vcoDM) of large well managed corn silage piles are low, the exposed silage face is a small portion of losses, and many proposed shrink mitigations appeared ineffective, possibly because shrink was low overall and they are largely directed at the exposed silage face. Copyright © 2015 Elsevier B.V. All rights reserved.

Peak exposures to main components of ash and gaseous diesel exhausts in closed and open ash loading stations at biomass-fuelled power plants.

PubMed

Laitinen, Juha; Koponen, Hanna; Sippula, Olli; Korpijärvi, Kirsi; Jumpponen, Mika; Laitinen, Sirpa; Aatamila, Marjaleena; Tissari, Jarkko; Karhunen, Tommi; Ojanen, Kari; Jokiniemi, Jorma; Korpinen, Leena

2017-10-01

Fly and bottom ashes are collected at power plants to reduce the environmental effects of energy production. However, handling the ashes causes health problems for operators, maintenance workers and truck drivers at the power plants. Hence, we evaluated ash loaders' peak inhalation exposures to the chemical components of ash and diesel exhausts in open and closed ash loading stations at biomass-fuelled combined heat and power plants. We also carried out chemical and morphological analyses of the ashes to evaluate their health hazard potential in order to find practical technical measures to reduce workers' exposure. On the basis of X-ray diffraction analyses, the main respirable crystalline ash compounds were SiO 2 , CaSO 4 , CaO, Ca 2 Al 2 SiO 7 , NaCl and Ca 3 Al 2 O 6 in the fly ashes and SiO 2 , KAlSi 3 O 8 , NaAlSi 3 O 8 and Ca 2 Al 2 SiO 7 in the bottom ashes. The short-term exposure levels of respirable crystalline silica, inhalable inorganic dust, Cr, Mn, Ni and nitric oxide exceeded their Finnish eight hours occupational exposure limit values in the closed ash loading station. According to our observations, more attention should be paid to the ash-moistening process, the use of tank trucks instead of open cassette flatbed trucks, and the sealing of the loading line from the silo to the truck which would prevent spreading the ash into the air. The idling time of diesel trucks should also be limited, and ash loading stations should be equipped with exhaust gas ventilators. If working conditions make it impossible to keep to the OEL values, workers must use respirators and protect their eyes and skin. Copyright © 2017 Elsevier Ltd. All rights reserved.

SpecViz: Interactive Spectral Data Analysis

NASA Astrophysics Data System (ADS)

Earl, Nicholas Michael; STScI

2016-06-01

The astronomical community is about to enter a new generation of scientific enterprise. With next-generation instrumentation and advanced capabilities, the need has arisen to equip astronomers with the necessary tools to deal with large, multi-faceted data. The Space Telescope Science Institute has initiated a data analysis forum for the creation, development, and maintenance of software tools for the interpretation of these new data sets. SpecViz is a spectral 1-D interactive visualization and analysis application built with Python in an open source development environment. A user-friendly GUI allows for a fast, interactive approach to spectral analysis. SpecViz supports handling of unique and instrument-specific data, incorporation of advanced spectral unit handling and conversions in a flexible, high-performance interactive plotting environment. Active spectral feature analysis is possible through interactive measurement and statistical tools. It can be used to build wide-band SEDs, with the capability of combining or overplotting data products from various instruments. SpecViz sports advanced toolsets for filtering and detrending spectral lines; identifying, isolating, and manipulating spectral features; as well as utilizing spectral templates for renormalizing data in an interactive way. SpecViz also includes a flexible model fitting toolset that allows for multi-component models, as well as custom models, to be used with various fitting and decomposition routines. SpecViz also features robust extension via custom data loaders and connection to the central communication system underneath the interface for more advanced control. Incorporation with Jupyter notebooks via connection with the active iPython kernel allows for SpecViz to be used in addition to a user’s normal workflow without demanding the user drastically alter their method of data analysis. In addition, SpecViz allows the interactive analysis of multi-object spectroscopy in the same straight-forward, consistent way. Through the development of such tools, STScI hopes to unify astronomical data analysis software for JWST and other instruments, allowing for efficient, reliable, and consistent scientific results.

Light-Weighted Automatic Import of Standardized Ontologies into the Content Management System Drupal.

PubMed

Beger, Christoph; Uciteli, Alexandr; Herre, Heinrich

2017-01-01

The amount of ontologies, which are utilizable for widespread domains, is growing steadily. BioPortal alone, embraces over 500 published ontologies with nearly 8 million classes. In contrast, the vast informative content of these ontologies is only directly intelligible by experts. To overcome this deficiency it could be possible to represent ontologies as web portals, which does not require knowledge about ontologies and their semantics, but still carries as much information as possible to the end-user. Furthermore, the conception of a complex web portal is a sophisticated process. Many entities must be analyzed and linked to existing terminologies. Ontologies are a decent solution for gathering and storing this complex data and dependencies. Hence, automated imports of ontologies into web portals could support both mentioned scenarios. The Content Management System (CMS) Drupal 8 is one of many solutions to develop web presentations with less required knowledge about programming languages and it is suitable to represent ontological entities. We developed the Drupal Upper Ontology (DUO), which models concepts of Drupal's architecture, such as nodes, vocabularies and links. DUO can be imported into ontologies to map their entities to Drupal's concepts. Because of Drupal's lack of import capabilities, we implemented the Simple Ontology Loader in Drupal (SOLID), a Drupal 8 module, which allows Drupal administrators to import ontologies based on DUO. Our module generates content in Drupal from existing ontologies and makes it accessible by the general public. Moreover Drupal offers a tagging system which may be amplified with multiple standardized and established terminologies by importing them with SOLID. Our Drupal module shows that ontologies can be used to model content of a CMS and vice versa CMS are suitable to represent ontologies in a user-friendly way. Ontological entities are presented to the user as discrete pages with all appropriate properties, links and tags.

Biomonitoring of exposure to N-methyl-2-pyrrolidone in workers of the automobile industry.

PubMed

Meier, Swetlana; Schindler, Birgit K; Koslitz, Stephan; Koch, Holger M; Weiss, Tobias; Käfferlein, Heiko U; Brüning, Thomas

2013-07-01

N-methyl-2-pyrrolidone (NMP) is an important organic solvent for varnishes in industry. NMP has been previously shown to be a developmental toxicant in rodents. This study reports current exposures to NMP in the spraying department of an automobile plant using biological monitoring. Two specific metabolites, 5-hydroxy-N-methyl-2-pyrrolidone (5-HNMP) and 2-hydroxy-N-methyl-succinimide (2-HMSI), were analyzed in 69 urine samples of 14 workers exposed to NMP and 9 nonexposed controls. Three different working tasks ('loading' and 'cleaning' of the sprayer system and 'wiping/packing' of the sprayed materials) and three sampling times (preshift, postshift, and preshift of the following day) were studied in exposed workers. Median exposures of 5-HNMP and 2-HMSI in postshift urine of exposed workers were 0.91 and 0.52mg g(-1) creatinine, respectively, whereas median levels in controls were below the limit of detection. Decreased levels of 5-HNMP were observed in preshift urine samples on the following day (0.39mg g(-1) creatinine) in exposed workers, while the concentration of 2-HMSI did not change (0.49mg g(-1) creatinine). Highest exposures occurred during sprayer cleaning with a maximum level of 8.31mg g(-1) creatinine of 5-HNMP in postshift urine. In contrast to 'wipers/packers', no decrease in 5-HNMP could be observed in preshift urine samples on day 2 of the 'loaders' and 'cleaners'. Overall, exposure in terms of 5-HNMP postshift and 2-HMSI preshift of the following day were well below the current biological limit values of the European Union (70 and 20mg g(-1) creatinine). Our results provide initial data on NMP exposure in the automobile industry and suggest that the analysis of 5-HNMP in preshift samples also provides essential information, particularly in situations involving direct handling of liquid NMP-containing formulations.

Risk assessment and management of occupational exposure to pesticides in agriculture.

PubMed

Maroni, M; Fanetti, Anna Clara; Metruccio, Francesca

2006-01-01

Nearly 50% of the world labour force is employed in agriculture. Over the last 50 years, agriculture has deeply changed with a massive utilisation of pesticides and fertilisers to enhance crop protection and production, food quality and food preservation. Pesticides are also increasingly employed for public health purposes and for domestic use. Pesticide are unique chemicals as they are intrinsically toxic for several biological targets, are deliberately spread into the environment, and their toxicity has a limited species selectivity. Pesticide toxicity depends on the compound family and is generally greater for the older compounds; in humans, they are responsible for acute poisonings as well as for long term health effects, including cancer and adverse effects on reproduction. Due to their intrinsic toxicity, in most countries a specific and complex legislation prescribes a thorough risk assessment process for pesticides prior to their entrance to the market (pre-marketing risk assessment). The post-marketing risk assessment takes place during the use of pesticides and aims at assessing the risk for exposed operators. The results of the risk assessment are the base for the health surveillance of exposed workers. Occupational exposure to pesticides in agriculture concerns product distributors, mixers and loaders, applicators, bystanders, and rural workers re-entering the fields shortly after treatment. Assessing and managing the occupational health risks posed by the use of pesticides in agriculture is a complex but essential task for occupational health specialists and toxicologists. In spite of the economic and social importance of agriculture, the health protection of agricultural workforce has been overlooked for too many years, causing an heavy tribute paid in terms of avoidable diseases, human sufferance, and economic losses. Particularly in the developing countries, where agricultural work is one of the predominant job, a sustainable model of development calls for more attention to occupational risks in agriculture. The experience of many countries has shown that prevention of health risk caused by pesticides is technically feasible and economically rewarding for the individuals and the whole community. A proper risk assessment and management of pesticide use is an essential component of this preventative

A Demonstration Project in New York and Virginia: Retrofitting Cost-Effective Roll-over Protective Structures (CROPS) on Tractors.

PubMed

Hard, D L; McKenzie, E A; Cantis, D; May, J; Sorensen, J; Bayes, B; Madden, E; Wyckoff, S; Stone, B; Maass, J

2015-07-01

The NIOSH cost-effective roll-over protective structure (CROPS) demonstration project sought to determine whether three prototype roll-over protective structures (ROPS) designed to be retrofitted on Ford 8N, Ford 3000, Ford 4000, and Massey Ferguson 135 tractors could be installed in the field and whether they would be acceptable by the intended end users (farmers). There were a total of 50 CROPS. demonstrators (25 in New York and 25 in Virginia), with 45 observers attending the New York CROPS demonstrations and 36 observers attending the Virginia CROPS demonstrations, for a total of 70 participants in New York and 61 in Virginia. The oldest retrofitted tractors were 77 to 62 years old, while the newest retrofitted tractors were 40 to 37 years old. The most frequently retrofitted tractor in the CROPS demonstration project was a Ford 3000 series tractor (n = 19; 38%), followed by Ford 4000 (n = 11; 22%), Massey Ferguson 135 (n = 11; 22%), and Ford 8N (n = 9; 18%). A major issue of CROPS retrofitting was the rear wheel fenders. The effort involved in disassembling the fenders (removing the old bolts was often faster by cutting them with a torch), modifying the fender mounting brackets, and then reinstalling the fenders with the CROPS generally required the most time. In addition, various other semi-permanent equipment attachments, such as front-end loaders, required additional time and effort to fit with the CROPS. Demonstrators were asked to rank the reasons why they had not retrofitted their tractors with ROPS until they had enrolled in the CROPS demonstration program. ROPS "cost too much" was ranked as the primary reason for participants in both states (80% for New York and 88% for Virginia). The second highest ranked reasons were "ROPS wasn't available" for Virginia (80%) and "hassle to find ROPS" for New York (69%). The third highest ranked reasons were "not enough time to find ROPS" for New York (67%) and "hassle to find ROPS" for Virginia (79%). All demonstrators and observers indicated that they were glad to have participated in the CROPS project.

Occupational risk factors for mycosis fungoides: a European multicenter case-control study.

PubMed

Morales-Suárez-Varela, Maria M; Olsen, Jorn; Johansen, Preben; Kaerlev, Linda; Guénel, Pascal; Arveux, Patrick; Wingren, Gun; Hardell, Lennart; Ahrens, Wolfgang; Stang, Andreas; Llopis, Agustin; Merletti, Franco; Aurrekoetxea, Juan Jose; Masala, Giovanna

2004-03-01

Mycosis fungoides (MF) is a rare disease with an unknown etiology. Its distribution suggests that occupational exposures may play a role. In the present study, we searched for occupational factors associated with MF. A European multicenter case-control study on seven rare cancers, including MF, was conducted from 1995 to 1997. Patients between 35 and 69 years of age diagnosed with MF (n = 134) were identified and their diagnoses were checked by a reference pathologist who classified 83 cases as definitive, 35 cases as possible, and 16 cases as not histologically verified. Of the 118 histologically verified cases, 104 were interviewed, of which 76 were definitive cases. As controls, we selected population controls and colon cancer controls to serve all seven case groups. Altogether, 833 colon cancer controls and 2071 population controls were interviewed. The response rate was 91.5% for cases (76 of the 83 definitive cases), and 66.6% for controls. A high risk of MF for men was observed in the industries of other non-metallic mineral products (Odds Ratio [OR] 5.3, 95% confidence interval [CI] = 1.7-16.2) and of wholesale trade (OR 3.6, 95% CI = 1.3-10.5). A high risk was found for female employees in the sector of pulp paper manufacture (OR 14.4, 95% CI = 2.2-95.1). The male occupations with the highest risks were glass formers, potters, and ceramics workers (OR 17.9, 95% CI = 5.4-59.4) and technical salesmen (OR 8.6, 95% CI = 2.4-30.8). For women, the occupations associated with the highest risks were government executives (OR 4.8, 95% CI = 1.0-22.6) and railway and road vehicles loaders (OR 3.9, 95% CI = 1.0-14.0). The results suggest that some occupational factors are associated with MF. Working as glass formers, pottery, and ceramics workers carried the highest risk, and these findings deserve further attention and replication. Females working in the paper and pulp industries may also be exposed to carcinogens of relevance to MF.

The caCORE Software Development Kit: streamlining construction of interoperable biomedical information services.

PubMed

Phillips, Joshua; Chilukuri, Ram; Fragoso, Gilberto; Warzel, Denise; Covitz, Peter A

2006-01-06

Robust, programmatically accessible biomedical information services that syntactically and semantically interoperate with other resources are challenging to construct. Such systems require the adoption of common information models, data representations and terminology standards as well as documented application programming interfaces (APIs). The National Cancer Institute (NCI) developed the cancer common ontologic representation environment (caCORE) to provide the infrastructure necessary to achieve interoperability across the systems it develops or sponsors. The caCORE Software Development Kit (SDK) was designed to provide developers both within and outside the NCI with the tools needed to construct such interoperable software systems. The caCORE SDK requires a Unified Modeling Language (UML) tool to begin the development workflow with the construction of a domain information model in the form of a UML Class Diagram. Models are annotated with concepts and definitions from a description logic terminology source using the Semantic Connector component. The annotated model is registered in the Cancer Data Standards Repository (caDSR) using the UML Loader component. System software is automatically generated using the Codegen component, which produces middleware that runs on an application server. The caCORE SDK was initially tested and validated using a seven-class UML model, and has been used to generate the caCORE production system, which includes models with dozens of classes. The deployed system supports access through object-oriented APIs with consistent syntax for retrieval of any type of data object across all classes in the original UML model. The caCORE SDK is currently being used by several development teams, including by participants in the cancer biomedical informatics grid (caBIG) program, to create compatible data services. caBIG compatibility standards are based upon caCORE resources, and thus the caCORE SDK has emerged as a key enabling technology for caBIG. The caCORE SDK substantially lowers the barrier to implementing systems that are syntactically and semantically interoperable by providing workflow and automation tools that standardize and expedite modeling, development, and deployment. It has gained acceptance among developers in the caBIG program, and is expected to provide a common mechanism for creating data service nodes on the data grid that is under development.

Sliding Clamp–DNA Interactions Are Required for Viability and Contribute to DNA Polymerase Management in Escherichia coli

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heltzel, J.; Scouten Ponticelli, S; Sanders, L

2009-01-01

Sliding clamp proteins topologically encircle DNA and play vital roles in coordinating the actions of various DNA replication, repair, and damage tolerance proteins. At least three distinct surfaces of the Escherichia coli {beta} clamp interact physically with the DNA that it topologically encircles. We utilized mutant {beta} clamp proteins bearing G66E and G174A substitutions ({beta}159), affecting the single-stranded DNA-binding region, or poly-Ala substitutions in place of residues 148-HQDVR-152 ({beta}148-152), affecting the double-stranded DNA binding region, to determine the biological relevance of clamp-DNA interactions. As part of this work, we solved the X-ray crystal structure of {beta}148-152, which verified that themore » poly-Ala substitutions failed to significantly alter the tertiary structure of the clamp. Based on functional assays, both {beta}159 and {beta}148-152 were impaired for loading and retention on a linear primed DNA in vitro. In the case of {beta}148-152, this defect was not due to altered interactions with the DnaX clamp loader, but rather was the result of impaired {beta}148-152-DNA interactions. Once loaded, {beta}148-152 was proficient for DNA polymerase III (Pol III) replication in vitro. In contrast, {beta}148-152 was severely impaired for Pol II and Pol IV replication and was similarly impaired for direct physical interactions with these Pols. Despite its ability to support Pol III replication in vitro, {beta}148-152 was unable to support viability of E. coli. Nevertheless, physiological levels of {beta}148-152 expressed from a plasmid efficiently complemented the temperature-sensitive growth phenotype of a strain expressing {beta}159 (dnaN159), provided that Pol II and Pol IV were inactivated. Although this strain was impaired for Pol V-dependent mutagenesis, inactivation of Pol II and Pol IV restored the Pol V mutator phenotype. Taken together, these results support a model in which a sophisticated combination of competitive clamp-DNA, clamp-partner, and partner-DNA interactions serve to manage the actions of the different E. coli Pols in vivo.« less

Non-destructive Quantitative Phase Analysis and Microstructural Characterization of Zirconium Coated U-10Mo Fuel Foils via Neutron Diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cummins, Dustin Ray; Vogel, Sven C.; Hollis, Kendall Jon

2016-10-18

This report uses neutron diffraction to investigate the crystal phase composition of uranium-molybdenum alloy foils (U-10Mo) for the CONVERT MP-1 Reactor Conversion Project, and determines the effect on alpha-uranium contamination following the deposition of a Zr metal diffusion layer by various methods: plasma spray deposition of Zr powders at LANL and hot co-rolling with Zr foils at BWXT. In summary, there is minimal decomposition of the gamma phase U-10Mo foil to alpha phase contamination following both plasma spraying and hot co-rolling. The average unit cell volume, i.e. lattice spacing, of the Zr layer can be mathematically extracted from the diffractionmore » data; co-rolled Zr matches well with literature values of bulk Zr, while plasma sprayed Zr shows a slight increase in the lattice spacing, indicative of interstitial oxygen in the lattice. Neutron diffraction is a beneficial alternative to conventional methods of phase composition, i.e. x ray diffraction (XRD) and destructive metallography. XRD has minimal penetration depth in high atomic number materials, particularly uranium, and can only probe the first few microns of the fuel plate; neutrons pass completely through the foil, allowing for bulk analysis of the foil composition and no issues with addition of cladding layers, as in the final, aluminum-clad reactor fuel plates. Destructive metallography requires skilled technicians, cutting of the foil into small sections, hazardous etching conditions, long polishing and microscopy times, etc.; the neutron diffraction system has an automated sample loader and can fit larger foils, so there is minimal analysis preparation; the total spectrum acquisition time is ~ 1 hour per sample. The neutron diffraction results are limited by spectra refinement/calculation times and the availability of the neutron beam source. In the case of LANSCE at Los Alamos, the beam operates ~50% of the year. Following the lessons learned from these preliminary results, optimizations to the process and analysis can be made, and neutron diffraction can become a viable and efficient technique for gamma/alpha phase composition determination for nuclear fuels.« less

Numerical analysis of laser-driven reservoir dynamics for shockless loading

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li Mu; Zhang Hongping; Sun Chengwei

2011-05-01

Laser-driven plasma loader for shockless compression provides a new approach to study the rapid compression response of materials not attainable in conventional shock experiments. In this method, the strain rate is varied from {approx}10{sup 6}/s to {approx}10{sup 8}/s, significantly higher than other shockless compression methods. Thus, this loading process is attractive in the research of solid material dynamics and astrophysics. The objective of the current study is to demonstrate the dynamic properties of the jet from the rear surface of the reservoir, and how important parameters such as peak load, rise time, shockless compression depth, and stagnating melt depth inmore » the sample vary with laser intensity, laser pulse length, reservoir thickness, vacuum gap size, and even the sample material. Numerical simulations based on the space-time conservation element and solution element method, together with the bulk ablation model, were used. The dynamics of the reservoir depend on the laser intensity, pulse length, equation of state, as well as the molecular structure of the reservoir. The critical pressure condition at which the reservoir will unload, similar to a gas or weak plasma, is 40-80 GPa before expansion. The momentum distribution bulges downward near the front of the plasma jet, which is an important characteristic that determines shockless compression. The total energy density is the most important parameter, and has great influence on the jet characteristics, and consequently on the shockless compression characteristics. If the reservoir is of a single material irradiated at a given laser condition, the relation of peak load and shockless compression depth is in conflict, and the highest loads correspond to the smallest thickness of sample. The temperature of jet front runs up several electron volts after impacting on the sample, and the heat transfer between the stagnating plasma and the sample is sufficiently significant to induce the melting of the sample surface. However, this diffusion heat wave propagates much more slowly than the stress wave, and has minimal effect on the shockless compression progress at a deeper position.« less

Structure and software tools of AIDA.

PubMed

Duisterhout, J S; Franken, B; Witte, F

1987-01-01

AIDA consists of a set of software tools to allow for fast development and easy-to-maintain Medical Information Systems. AIDA supports all aspects of such a system both during development and operation. It contains tools to build and maintain forms for interactive data entry and on-line input validation, a database management system including a data dictionary and a set of run-time routines for database access, and routines for querying the database and output formatting. Unlike an application generator, the user of AIDA may select parts of the tools to fulfill his needs and program other subsystems not developed with AIDA. The AIDA software uses as host language the ANSI-standard programming language MUMPS, an interpreted language embedded in an integrated database and programming environment. This greatly facilitates the portability of AIDA applications. The database facilities supported by AIDA are based on a relational data model. This data model is built on top of the MUMPS database, the so-called global structure. This relational model overcomes the restrictions of the global structure regarding string length. The global structure is especially powerful for sorting purposes. Using MUMPS as a host language allows the user an easy interface between user-defined data validation checks or other user-defined code and the AIDA tools. AIDA has been designed primarily for prototyping and for the construction of Medical Information Systems in a research environment which requires a flexible approach. The prototyping facility of AIDA operates terminal independent and is even to a great extent multi-lingual. Most of these features are table-driven; this allows on-line changes in the use of terminal type and language, but also causes overhead. AIDA has a set of optimizing tools by which it is possible to build a faster, but (of course) less flexible code from these table definitions. By separating the AIDA software in a source and a run-time version, one is able to write implementation-specific code which can be selected and loaded by a special source loader, being part of the AIDA software. This feature is also accessible for maintaining software on different sites and on different installations.

The clinical trial landscape in oncology and connectivity of somatic mutational profiles to targeted therapies.

PubMed

Patterson, Sara E; Liu, Rangjiao; Statz, Cara M; Durkin, Daniel; Lakshminarayana, Anuradha; Mockus, Susan M

2016-01-16

Precision medicine in oncology relies on rapid associations between patient-specific variations and targeted therapeutic efficacy. Due to the advancement of genomic analysis, a vast literature characterizing cancer-associated molecular aberrations and relative therapeutic relevance has been published. However, data are not uniformly reported or readily available, and accessing relevant information in a clinically acceptable time-frame is a daunting proposition, hampering connections between patients and appropriate therapeutic options. One important therapeutic avenue for oncology patients is through clinical trials. Accordingly, a global view into the availability of targeted clinical trials would provide insight into strengths and weaknesses and potentially enable research focus. However, data regarding the landscape of clinical trials in oncology is not readily available, and as a result, a comprehensive understanding of clinical trial availability is difficult. To support clinical decision-making, we have developed a data loader and mapper that connects sequence information from oncology patients to data stored in an in-house database, the JAX Clinical Knowledgebase (JAX-CKB), which can be queried readily to access comprehensive data for clinical reporting via customized reporting queries. JAX-CKB functions as a repository to house expertly curated clinically relevant data surrounding our 358-gene panel, the JAX Cancer Treatment Profile (JAX CTP), and supports annotation of functional significance of molecular variants. Through queries of data housed in JAX-CKB, we have analyzed the landscape of clinical trials relevant to our 358-gene targeted sequencing panel to evaluate strengths and weaknesses in current molecular targeting in oncology. Through this analysis, we have identified patient indications, molecular aberrations, and targeted therapy classes that have strong or weak representation in clinical trials. Here, we describe the development and disseminate system methods for associating patient genomic sequence data with clinically relevant information, facilitating interpretation and providing a mechanism for informing therapeutic decision-making. Additionally, through customized queries, we have the capability to rapidly analyze the landscape of targeted therapies in clinical trials, enabling a unique view into current therapeutic availability in oncology.

Functional and molecular characterization of transmembrane intracellular pH regulators in human dental pulp stem cells.

PubMed

Chen, Gunng-Shinng; Lee, Shiao-Pieng; Huang, Shu-Fu; Chao, Shih-Chi; Chang, Chung-Yi; Wu, Gwo-Jang; Li, Chung-Hsing; Loh, Shih-Hurng

2018-06-01

Homeostasis of intracellular pH (pH i ) plays vital roles in many cell functions, such as proliferation, apoptosis, differentiation and metastasis. Thus far, Na + -H + exchanger (NHE), Na + -HCO 3 - co-transporter (NBC), Cl - /HCO 3 - exchanger (AE) and Cl - /OH - exchanger (CHE) have been identified to co-regulate pH i homeostasis. However, functional and biological pH i -regulators in human dental pulp stem cells (hDPSCs) have yet to be identified. Microspectrofluorimetry technique with pH-sensitive fluorescent dye, BCECF, was used to detect pH i changes. NH 4 Cl and Na + -acetate pre-pulse were used to induce intracellular acidosis and alkalosis, respectively. Isoforms of pH i -regulators were detected by Western blot technique. The resting pH i was no significant difference between that in HEPES-buffered (nominal HCO 3 - -free) solution or CO 2 /HCO 3 -buffered system (7.42 and 7.46, respectively). The pH i recovery following the induced-intracellular acidosis was blocked completely by removing [Na + ] o , while only slowed (-63%) by adding HOE694 (a NHE1 specific inhibitor) in HEPES-buffered solution. The pH i recovery was inhibited entirely by removing [Na + ] o , while adding HOE 694 pulse DIDS (an anion-transporter inhibitor) only slowed (-55%) the acid extrusion. Both in HEPES-buffered and CO 2 /HCO 3 -buffered system solution, the pH i recovery after induced-intracellular alkalosis was entirely blocked by removing [Cl - ] o . Western blot analysis showed the isoforms of pH i regulators, including NHE1/2, NBCe1/n1, AE1/2/3/4 and CHE in the hDPSCs. We demonstrate for the first time that resting pH i is significantly higher than 7.2 and meditates functionally by two Na + -dependent acid extruders (NHE and NBC), two Cl - -dependent acid loaders (CHE and AE) and one Na + -independent acid extruder(s) in hDPSCs. These findings provide novel insight for basic and clinical treatment of dentistry. Copyright © 2018 Elsevier Ltd. All rights reserved.

Occupational hygiene in terms of volatile organic compounds (VOCs) and bioaerosols at two solid waste management plants in Finland

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lehtinen, Jenni, E-mail: jenni.k.lehtinen@jyu.fi; Tolvanen, Outi; Nivukoski, Ulla

Highlights: ► Odorous VOCs: acetic acid, 2,3-butanedione, ethyl acetate, alpha-pinene and limonene. ► VOC concentrations did not exceed occupational exposure limit concentrations. ► 2,3-Butanedione as the health effecting compound is discussed. ► Endotoxin concentrations may cause health problems in waste treatment. - Abstract: Factors affecting occupational hygiene were measured at the solid waste transferring plant at Hyvinkää and at the optic separation plant in Hämeenlinna. Measurements consisted of volatile organic compounds (VOCs) and bioaerosols including microbes, dust and endotoxins. The most abundant compounds in both of the plants were aliphatic and aromatic hydrocarbons, esters of carboxylic acids, ketones and terpenes.more » In terms of odour generation, the most important emissions were acetic acid, 2,3-butanedione, ethyl acetate, alpha-pinene and limonene due to their low threshold odour concentrations. At the optic waste separation plant, limonene occurred at the highest concentration of all single compounds of identified VOCs. The concentration of any single volatile organic compound did not exceed the occupational exposure limit (OEL) concentration. However, 2,3-butanedione as a health risk compound is discussed based on recent scientific findings linking it to lung disease. Microbe and dust concentrations were low at the waste transferring plant. Only endotoxin concentrations may cause health problems; the average concentration inside the plant was 425 EU/m{sup 3} which clearly exceeded the threshold value of 90 EU/m{sup 3}. In the wheel loader cabin the endotoxin concentrations were below 1 EU/m{sup 3}. High microbial and endotoxin concentrations were measured in the processing hall at the optic waste separation plant. The average concentration of endotoxins was found to be 10,980 EU/m{sup 3}, a concentration which may cause health risks. Concentrations of viable fungi were quite high in few measurements in the control room. The most problematic factor was endotoxins whose average measured concentrations was 4853 EU/m{sup 3}.« less

Assessment and evaluation of noise controls on roof bolting equipment and a method for predicting sound pressure levels in underground coal mining

NASA Astrophysics Data System (ADS)

Matetic, Rudy J.

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation's miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: (1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; (2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; (3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and (4) described a method for determining an operators' noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

The caCORE Software Development Kit: Streamlining construction of interoperable biomedical information services

PubMed Central

Phillips, Joshua; Chilukuri, Ram; Fragoso, Gilberto; Warzel, Denise; Covitz, Peter A

2006-01-01

Background Robust, programmatically accessible biomedical information services that syntactically and semantically interoperate with other resources are challenging to construct. Such systems require the adoption of common information models, data representations and terminology standards as well as documented application programming interfaces (APIs). The National Cancer Institute (NCI) developed the cancer common ontologic representation environment (caCORE) to provide the infrastructure necessary to achieve interoperability across the systems it develops or sponsors. The caCORE Software Development Kit (SDK) was designed to provide developers both within and outside the NCI with the tools needed to construct such interoperable software systems. Results The caCORE SDK requires a Unified Modeling Language (UML) tool to begin the development workflow with the construction of a domain information model in the form of a UML Class Diagram. Models are annotated with concepts and definitions from a description logic terminology source using the Semantic Connector component. The annotated model is registered in the Cancer Data Standards Repository (caDSR) using the UML Loader component. System software is automatically generated using the Codegen component, which produces middleware that runs on an application server. The caCORE SDK was initially tested and validated using a seven-class UML model, and has been used to generate the caCORE production system, which includes models with dozens of classes. The deployed system supports access through object-oriented APIs with consistent syntax for retrieval of any type of data object across all classes in the original UML model. The caCORE SDK is currently being used by several development teams, including by participants in the cancer biomedical informatics grid (caBIG) program, to create compatible data services. caBIG compatibility standards are based upon caCORE resources, and thus the caCORE SDK has emerged as a key enabling technology for caBIG. Conclusion The caCORE SDK substantially lowers the barrier to implementing systems that are syntactically and semantically interoperable by providing workflow and automation tools that standardize and expedite modeling, development, and deployment. It has gained acceptance among developers in the caBIG program, and is expected to provide a common mechanism for creating data service nodes on the data grid that is under development. PMID:16398930

DEVELOPMENT OF REMOTE HANFORD CONNECTOR GASKET REPLACEMENT TOOLING FOR DWPF

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krementz, D.; Coughlin, Jeffrey

2009-05-05

The Defense Waste Processing Facility (DWPF) requested the Savannah River National Laboratory (SRNL) to develop tooling and equipment to remotely replace gaskets in mechanical Hanford connectors to reduce personnel radiation exposure as compared to the current hands-on method. It is also expected that radiation levels will continually increase with future waste streams. The equipment is operated in the Remote Equipment Decontamination Cell (REDC), which is equipped with compressed air, two master-slave manipulators (MSM's) and an electro-mechanical manipulator (EMM) arm for operation of the remote tools. The REDC does not provide access to electrical power, so the equipment must be manuallymore » or pneumatically operated. The MSM's have a load limit at full extension of ten pounds, which limited the weight of the installation tool. In order to remotely replace Hanford connector gaskets several operations must be performed remotely, these include: removal of the spent gasket and retaining ring (retaining ring is also called snap ring), loading the new snap ring and gasket into the installation tool and installation of the new gasket into the Hanford connector. SRNL developed and tested tools that successfully perform all of the necessary tasks. Removal of snap rings from horizontal and vertical connectors is performed by separate air actuated retaining ring removal tools and is manipulated in the cell by the MSM. In order install a new gasket, the snap ring loader is used to load a new snap ring into a groove in the gasket installation tool. A new gasket is placed on the installation tool and retained by custom springs. An MSM lifts the installation tool and presses the mounted gasket against the connector block. Once the installation tool is in position, the gasket and snap ring are installed onto the connector by pneumatic actuation. All of the tools are located on a custom work table with a pneumatic valve station that directs compressed air to the desired tool and vents the tools as needed. Extensive testing of tooling operation was performed in the DWPF manipulator repair shop. This testing allowed the operators to gain confidence before the equipment was exposed to radioactive contamination. The testing also led to multiple design improvements. On July 17 and 29, 2008 the Remote Gasket Replacement Tooling was successfully demonstrated in the REDC at the DWPF of The Savannah River Site.« less

SU-G-201-17: Verification of Dose Distributions From High-Dose-Rate Brachytherapy Ir-192 Source Using a Multiple-Array-Diode-Detector (MapCheck2)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harpool, K; De La Fuente Herman, T; Ahmad, S

Purpose: To investigate quantitatively the accuracy of dose distributions for the Ir-192 high-dose-rate (HDR) brachytherapy source calculated by the Brachytherapy-Planning system (BPS) and measured using a multiple-array-diode-detector in a heterogeneous medium. Methods: A two-dimensional diode-array-detector system (MapCheck2) was scanned with a catheter and the CT-images were loaded into the Varian-Brachytherapy-Planning which uses TG-43-formalism for dose calculation. Treatment plans were calculated for different combinations of one dwell-position and varying irradiation times and different-dwell positions and fixed irradiation time with the source placed 12mm from the diode-array plane. The calculated dose distributions were compared to the measured doses with MapCheck2 delivered bymore » an Ir-192-source from a Nucletron-Microselectron-V2-remote-after-loader. The linearity of MapCheck2 was tested for a range of dwell-times (2–600 seconds). The angular effect was tested with 30 seconds irradiation delivered to the central-diode and then moving the source away in increments of 10mm. Results: Large differences were found between calculated and measured dose distributions. These differences are mainly due to absence of heterogeneity in the dose calculation and diode-artifacts in the measurements. The dose differences between measured and calculated due to heterogeneity ranged from 5%–12% depending on the position of the source relative to the diodes in MapCheck2 and different heterogeneities in the beam path. The linearity test of the diode-detector showed 3.98%, 2.61%, and 2.27% over-response at short irradiation times of 2, 5, and 10 seconds, respectively, and within 2% for 20 to 600 seconds (p-value=0.05) which depends strongly on MapCheck2 noise. The angular dependency was more pronounced at acute angles ranging up to 34% at 5.7 degrees. Conclusion: Large deviations between measured and calculated dose distributions for HDR-brachytherapy with Ir-192 may be improved when considering medium heterogeneity and dose-artifact of the diodes. This study demonstrates that multiple-array-diode-detectors provide practical and accurate dosimeter to verify doses delivered from the brachytherapy Ir-192-source.« less

Recurrence and interoccurrence behavior of self-organized complex phenomena

NASA Astrophysics Data System (ADS)

Abaimov, S. G.; Turcotte, D. L.; Shcherbakov, R.; Rundle, J. B.

2007-08-01

The sandpile, forest-fire and slider-block models are said to exhibit self-organized criticality. Associated natural phenomena include landslides, wildfires, and earthquakes. In all cases the frequency-size distributions are well approximated by power laws (fractals). Another important aspect of both the models and natural phenomena is the statistics of interval times. These statistics are particularly important for earthquakes. For earthquakes it is important to make a distinction between interoccurrence and recurrence times. Interoccurrence times are the interval times between earthquakes on all faults in a region whereas recurrence times are interval times between earthquakes on a single fault or fault segment. In many, but not all cases, interoccurrence time statistics are exponential (Poissonian) and the events occur randomly. However, the distribution of recurrence times are often Weibull to a good approximation. In this paper we study the interval statistics of slip events using a slider-block model. The behavior of this model is sensitive to the stiffness α of the system, α=kC/kL where kC is the spring constant of the connector springs and kL is the spring constant of the loader plate springs. For a soft system (small α) there are no system-wide events and interoccurrence time statistics of the larger events are Poissonian. For a stiff system (large α), system-wide events dominate the energy dissipation and the statistics of the recurrence times between these system-wide events satisfy the Weibull distribution to a good approximation. We argue that this applicability of the Weibull distribution is due to the power-law (scale invariant) behavior of the hazard function, i.e. the probability that the next event will occur at a time t0 after the last event has a power-law dependence on t0. The Weibull distribution is the only distribution that has a scale invariant hazard function. We further show that the onset of system-wide events is a well defined critical point. We find that the number of system-wide events NSWE satisfies the scaling relation NSWE ∝(α-αC)δ where αC is the critical value of the stiffness. The system-wide events represent a new phase for the slider-block system.

Collaborative WorkBench for Researchers - Work Smarter, Not Harder

NASA Technical Reports Server (NTRS)

Ramachandran, Rahul; Kuo, Kwo-sen; Maskey, Manil; Lynnes, Christopher

2014-01-01

It is important to define some commonly used terminology related to collaboration to facilitate clarity in later discussions. We define provisioning as infrastructure capabilities such as computation, storage, data, and tools provided by some agency or similarly trusted institution. Sharing is defined as the process of exchanging data, programs, and knowledge among individuals (often strangers) and groups. Collaboration is a specialized case of sharing. In collaboration, sharing with others (usually known colleagues) is done in pursuit of a common scientific goal or objective. Collaboration entails more dynamic and frequent interactions and can occur at different speeds. Synchronous collaboration occurs in real time such as editing a shared document on the fly, chatting, video conference, etc., and typically requires a peer-to-peer connection. Asynchronous collaboration is episodic in nature based on a push-pull model. Examples of asynchronous collaboration include email exchanges, blogging, repositories, etc. The purpose of a workbench is to provide a customizable framework for different applications. Since the workbench will be common to all the customized tools, it promotes building modular functionality that can be used and reused by multiple tools. The objective of our Collaborative Workbench (CWB) is thus to create such an open and extensible framework for the Earth Science community via a set of plug-ins. Our CWB is based on the Eclipse [2] Integrated Development Environment (IDE), which is designed as a small kernel containing a plug-in loader for hundreds of plug-ins. The kernel itself is an implementation of a known specification to provide an environment for the plug-ins to execute. This design enables modularity, where discrete chunks of functionality can be reused to build new applications. The minimal set of plug-ins necessary to create a client application is called the Eclipse Rich Client Platform (RCP) [3]; The Eclipse RCP also supports thousands of community-contributed plug-ins, making it a popular development platform for many diverse applications including the Science Activity Planner developed at JPL for the Mars rovers [4] and the scientific experiment tool Gumtree [5]. By leveraging the Eclipse RCP to provide an open, extensible framework, a CWB supports customizations via plug-ins to build rich user applications specific for Earth Science. More importantly, CWB plug-ins can be used by existing science tools built off Eclipse such as IDL or PyDev to provide seamless collaboration functionalities.

Prevalence and pattern of occupational exposure to whole body vibration in Great Britain: findings from a national survey

PubMed Central

Palmer, K.; Griffin, M.; Bendall, H.; Pannett, B.; Coggon, D.

2000-01-01

OBJECTIVES—To estimate the number of workers in Great Britain with significant occupational exposure to whole body vibration (WBV) and to identify the common sources of exposure and the occupations and industries where such exposures arise.
METHODS—A postal questionnaire was posted to a random community sample of 22 194 men and women of working age. Among other things, the questionnaire asked about exposure to WBV in the past week, including occupational and common non-occupational sources. Responses were assessed by occupation and industry, and national prevalence estimates were derived from census information. Estimates were also made of the average estimated daily personal dose of vibration (eVDV).
RESULTS—From the 12 907 responses it was estimated that 7.2 million men and 1.8 million women in Great Britain are exposed to WBV at work in a 1 week period if the occupational use of cars, vans, buses, trains, and motor cycles is included within the definition of exposure. The eVDV of >374 000 men and 9000 women was estimated to exceed a proposed British Standard action level of 15 ms-1.75. Occupations in which the estimated exposures most often exceeded 15 ms-1.75 included forklift truck and mechanical truck drivers, farm owners and managers, farm workers, and drivers of road goods vehicles. These occupations also contributed the largest estimated numbers of workers in Great Britain with such levels of exposure. The highest estimated median occupational eVDVs were found in forklift truck drivers, drivers of road goods vehicles, bus and coach drivers, and technical and wholesale sales representatives, among whom a greater contribution to total dose was received from occupational exposures than from non-occupational ones; but in many other occupations the reverse applied. The most common sources of occupational exposure to WBV are cars, vans, forklift trucks, lorries, tractors, buses, and loaders.
CONCLUSIONS—Exposure to whole body vibration is common, but only a small proportion of exposures exceed the action level proposed in British standards, and in many occupations, non-occupational sources are more important than those at work. The commonest occupational sources of WBV and occupations with particularly high exposures have been identified, providing a basis for targeting future control activities.


Keywords: whole body vibration; population; prevalence; exposure PMID:10810108

Footprint Representation of Planetary Remote Sensing Data

NASA Astrophysics Data System (ADS)

Walter, S. H. G.; Gasselt, S. V.; Michael, G.; Neukum, G.

The geometric outline of remote sensing image data, the so called footprint, can be represented as a number of coordinate tuples. These polygons are associated with according attribute information such as orbit name, ground- and image resolution, solar longitude and illumination conditions to generate a powerful base for classification of planetary experiment data. Speed, handling and extended capabilites are the reasons for using geodatabases to store and access these data types. Techniques for such a spatial database of footprint data are demonstrated using the Relational Database Management System (RDBMS) PostgreSQL, spatially enabled by the PostGIS extension. Exemplary, footprints of the HRSC and OMEGA instruments, both onboard ESA's Mars Express Orbiter, are generated and connected to attribute information. The aim is to provide high-resolution footprints of the OMEGA instrument to the science community for the first time and make them available for web-based mapping applications like the "Planetary Interactive GIS-on-the-Web Analyzable Database" (PIG- WAD), produced by the USGS. Map overlays with HRSC or other instruments like MOC and THEMIS (footprint maps are already available for these instruments and can be integrated into the database) allow on-the-fly intersection and comparison as well as extended statistics of the data. Footprint polygons are generated one by one using standard software provided by the instrument teams. Attribute data is calculated and stored together with the geometric information. In the case of HRSC, the coordinates of the footprints are already available in the VICAR label of each image file. Using the VICAR RTL and PostgreSQL's libpq C library they are loaded into the database using the Well-Known Text (WKT) notation by the Open Geospatial Consortium, Inc. (OGC). For the OMEGA instrument, image data is read using IDL routines developed and distributed by the OMEGA team. Image outlines are exported together with relevant attribute data to the industry standard Shapefile format. These files are translated to a Structured Query Language (SQL) command sequence suitable for insertion into the PostGIS/PostgrSQL database using the shp2pgsql data loader provided by the PostGIS software. PostgreSQL's advanced features such as geometry types, rules, operators and functions allow complex spatial queries and on-the-fly processing of data on DBMS level e.g. generalisation of the outlines. Processing done by the DBMS, visualisation via GIS systems and utilisation for web-based applications like mapservers will be demonstrated.

Real-world emissions of in-use off-road vehicles in Mexico.

PubMed

Zavala, Miguel; Huertas, Jose Ignacio; Prato, Daniel; Jazcilevich, Aron; Aguilar, Andrés; Balam, Marco; Misra, Chandan; Molina, Luisa T

2017-09-01

Off-road vehicles used in construction and agricultural activities can contribute substantially to emissions of gaseous pollutants and can be a major source of submicrometer carbonaceous particles in many parts of the world. However, there have been relatively few efforts in quantifying the emission factors (EFs) and for estimating the potential emission reduction benefits using emission control technologies for these vehicles. This study characterized the black carbon (BC) component of particulate matter and NOx, CO, and CO 2 EFs of selected diesel-powered off-road mobile sources in Mexico under real-world operating conditions using on-board portable emissions measurements systems (PEMS). The vehicles sampled included two backhoes, one tractor, a crane, an excavator, two front loaders, two bulldozers, an air compressor, and a power generator used in the construction and agricultural activities. For a selected number of these vehicles the emissions were further characterized with wall-flow diesel particle filters (DPFs) and partial-flow DPFs (p-DPFs) installed. Fuel-based EFs presented less variability than time-based emission rates, particularly for the BC. Average baseline EFs in working conditions for BC, NOx, and CO ranged from 0.04 to 5.7, from 12.6 to 81.8, and from 7.9 to 285.7 g/kg-fuel, respectively, and a high dependency by operation mode and by vehicle type was observed. Measurement-base frequency distributions of EFs by operation mode are proposed as an alternative method for characterizing the variability of off-road vehicles emissions under real-world conditions. Mass-based reductions for black carbon EFs were substantially large (above 99%) when DPFs were installed and the vehicles were idling, and the reductions were moderate (in the 20-60% range) for p-DPFs in working operating conditions. The observed high variability in measured EFs also indicates the need for detailed vehicle operation data for accurately estimating emissions from off-road vehicles in emissions inventories. Measurements of off-road vehicles used in construction and agricultural activities in Mexico using on-board portable emissions measurements systems (PEMS) showed that these vehicles can be major sources of black carbon and NO X . Emission factors varied significantly under real-world operating conditions, suggesting the need for detailed vehicle operation data for accurately estimating emissions inventories. Tests conducted in a selected number of sampled vehicles indicated that diesel particle filters (DPFs) are an effective technology for control of diesel particulate emissions and can provide potentially large emissions reduction in Mexico if widely implemented.

Organismal versus Environmental Control of the Carbon Isotope Composition of Dicot Angiosperm Pollen: Implications for Paleoenvironmental Reconstruction

NASA Astrophysics Data System (ADS)

King, D. P.; Schubert, B.; Foelber, K.; Jahren, H.

2011-12-01

The prevalence and diagenetic resilience of palynomorphs in Proterozoic and Phanerozoic sediments has led researchers to investigate its potential as an environmental proxy based on its stable isotope composition. Towards this, Loader and Hemming (2001), noted that the carbon isotope composition (δ13C) of modern Pinus sylvestris pollen exine correlates with the developmental period temperature (°C) of the pollen (R2=0.68), implying that the δ13C of gymnosperm pollen could be quantitatively utilized as a paleotemperature proxy. However, the majority of pollen-producing organisms during the last ~120 million years have been angiosperms, which are subject to complex internal signaling for reproduction, in addition to environmental triggers. Because these internal signals control the relative proportion of lipids, long-chain fatty acids, and polysaccharides within pollen grains, we hypothesized that the δ13C variability in pollen (δ13Cpollen) from several plants subject to the same external environmental parameters is of the same magnitude as the amount attributed to the environment for gymnosperms. Within growth chambers, the test organism (Brassica rapa) was cultivated under constant light, water, pCO2, and nutrient supply, but exhibited average δ13Cpollen variability = 4.35% within any chamber (n = 6 to 8 plants per chamber). Field experiments were also conducted in which the pollen from the test organism (Hibiscus spp.) was sampled from several botanical gardens within the state of Hawaii. Pollen collected from any one botanical garden exhibited an average δ13Cpollen variability = 4.5% (up to 5 plants per garden). Upon comparing chambers operating at different temperatures (17°C to 32°C), we discovered no correlation (R2=0.01) between the developmental period temperature (°C) and the δ13C of B. rapa pollen; similarly, no correlation was found between the δ13C of Hibiscus pollen and its developmental period temperature (°C) (R2=0.12). This work underscores the lack of consistent environmental control over the δ13C value of pollen, and suggests that the carbon isotope composition of dicot pollen cannot be used to determine paleotemperatures. Future work centers on our hypothesis that the δ13C variability in angiosperm pollen results from differential reproductive potency and associated differences in the percentages of lipids, long-chain fatty acids, and polysaccharides within pollen. Towards this we will quantify the relationship between the chemical composition of flower-aggregate pollen and its δ13C value, given the δ13C value of isolated end-member constituents.

Canada's National Building Stone: Tyndall Stone from Manitoba

NASA Astrophysics Data System (ADS)

Pratt, Brian R.; Young, Graham A.; Dobrzanski, Edward P.

2016-04-01

Tyndall Stone is a distinctively mottled and highly fossiliferous dolomitic limestone that belongs to the Selkirk Member of the Red River Formation, of Late Ordovician (Katian) age. It has been quarried at Garson, Manitoba, 37 km northeast of Winnipeg, since 1895, although other quarries in the area go back to 1832. Tyndall Stone, so named because it was shipped by rail from nearby Tyndall, is currently produced by Gillis Quarries Limited. It has various uses as a dimension stone. Large slabs, most often cut parallel to bedding, face the exterior or interior of many important buildings such as the Parliament Buildings and the Canadian Museum of Civilization in the Ottawa area, the Empress Hotel in Victoria, and the provincial legislatures in Winnipeg and Regina, as well as many commercial buildings especially in the Canadian prairies. At the quarries, the stone is cut vertically, using eight foot (2.44 m) diameter saws mounted on one hundred foot (30.5 m) tracks, then split into 6-8 tonne blocks that are moved using front-end loaders. Gillis Quarries operates a large finishing plant with an area of about 4000 m2. Stone is processed along advanced cutting lines that feature eight primary saws and six gantry saw stations, allowing it to be made into a variety of sizes, shapes, and finishes. The Selkirk Member is 43 m thick and the stone is extracted from a 6-8 m thick interval within the lower part. The upper beds tend to be more buff-coloured than the grey lower beds due to weathering by groundwater. The stone is massive, but extracted blocks are less than ~1m thick due to splitting along stylolites. Consisting of bioturbated wackestone to packstone, the Tyndall Stone was deposited in a shallow-marine environment within the photic zone, in the central part of the vast equatorial epicontinental sea that covered much of Laurentia. Scattered thin, bioclastic grainstone lenses record brief, low-energy storm events. The distinctive mottles are formed by dolomitized burrows belonging to Thalassinoides, which were interconnected galleries likely made by arthropods after the sediment became somewhat consolidated. Slabs bearing fossils are typically avoided in construction for esthetic reasons and because some impart weaknesses. Such slabs have, however, become increasingly popular for decorative surfaces not exposed to the elements, since the macrofossil content is so striking. Most common are receptaculitids, followed by solitary rugose corals, stromatoporoid sponges, colonial rugose and tabulate corals, brachiopods, bryozoans, gastropods, cephalopods, and trilobites; echinoderm ossicles are common in the muddy matrix. Fossil relative abundances vary stratigraphically, suggesting that subtle environmental changes took place over time.

WOVOdat Design Document: The Schema, Table Descriptions, and Create Table Statements for the Database of Worldwide Volcanic Unrest (WOVOdat Version 1.0)

USGS Publications Warehouse

Venezky, Dina Y.; Newhall, Christopher G.

2007-01-01

WOVOdat Overview During periods of volcanic unrest, the ability to forecast near future activity has been a primary concern for human populations living near volcanoes. Our ability to forecast future activity and mitigate hazards is based on knowledge of previous activity at the volcano exhibiting unrest and knowledge of previous activity at similar volcanoes. A small set of experts with past experience are often involved in forecasting. We need to both preserve the knowledge the experts use and continue to investigate volcanic data to make better forecasts. Advances in instrumentation, networking, and data storage technologies have greatly increased our ability to collect volcanic data and share observations with our colleagues. The wealth of data creates numerous opportunities for gaining a better understanding of magmatic conditions and processes, if the data can be easily accessed for comparison. To allow for comparison of volcanic unrest data, we are creating a central database called WOVOdat. WOVOdat will contain a subset of time-series and geo-referenced data from each WOVO observatory in common and easily accessible formats. WOVOdat is being created for volcano experts in charge of forecasting volcanic activity, scientists investigating volcanic processes, and the public. The types of queries each of these groups might ask range from, 'What volcanoes were active in November of 2002?' and 'What are the relationships between tectonic earthquakes and volcanic processes?' to complex analyses of volcanic unrest to determine what future activity might occur. A new structure for storing and accessing our data was needed to examine processes across a wide range of volcanologic conditions. WOVOdat provides this new structure using relationships to connect the data parameters such that searches can be created for analogs of unrest. The subset of data that will fill WOVOdat will continue to be collected by the observatories, who will remain the primary archives of raw and detailed data on individual episodes of unrest. MySQL, an Open Source database, was chosen as the WOVOdat database for its integration with common web languages. The question of where the data will be stored and how the disparate data sets will be integrated will not be discussed in detail here. The focus of this document is to explain the data types, formats, and table organization chosen for WOVOdat 1.0. It was written for database administrators, data loaders, query writers, and anyone who monitors volcanoes. We begin with an overview of several challenges faced and solutions used in creating the WOVOdat schema. Specifics are then given for the parameters and table organization. After each table organization section, basic create table statements are included for viewing the database field formats. In the next stage of the project, scripts will be needed for data conversion, entry, and cleansing. Views will also need to be created once the data have been loaded and the basic queries are better known. Many questions and opportunities remain. We look forward to the growth and continual improvement in efficiency of the system. We hope WOVOdat will improve our understanding of magmatic systems and help mitigate future volcanic hazards.

Effects of outgassing of loader chamber walls on hydriding of thin films for commercial applications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Provo, James L., E-mail: jlprovo@verizon.net

2014-07-01

An important aspect of understanding industrial processing is to know the characteristics of the materials used in such processes. A study was performed to determine the effects of hydriding chamber material on the degree of hydriding for the commercial production of thin film hydride targets for various research universities, commercial companies, and government national laboratories. The goal was to increase the degree of hydriding of various thin film hydrides and to study the vacuum environment during air-exposure hydriding. For this purpose, dynamic residual gas analysis during deuterium gas hydride processing was utilized with erbium thin films, employing a special set-upmore » for direct dynamic hydride gas sampling during processing at elevated temperature and full loading gas pressure. Complete process data for (1) a copper–(1.83 wt. %)beryllium wet hydrogen fired passivated (600 °C–1 h) externally heated pipe hydriding chamber are reported. Dynamic residual gas analysis comparisons during hydriding are presented for hydriding chambers made from (2) alumina (99.8 wt. %), (3) copper (with an interior aluminum coating ∼10 k Å thick, and (4) for a stainless-steel air-fired passivated (900 °C–1 h) chamber. Dynamic data with deuterium gas in the chamber at the hydriding temperature (450 °C) showed the presence and growth of water vapor (D{sub 2}O) and related mixed ion species(H{sub 2}O{sup +}, HDO{sup +}, D{sub 2}O{sup +}, and OD{sup +}) from hydrogen isotope exchange reactions during the 1 h process time. Peaks at mass-to-charge ratios (i.e., m/e) of 12(C{sup +}), 16(CD{sub 2}{sup +}), 17(CHD{sub 2}{sup +}), and 18(CD{sub 3}{sup +}, OD{sup +}) increased for approximately the first half hour of a 1 h hydriding process and then approach steady state. Mass-to-charge peaks at 19(HDO{sup +}) and 20(D{sub 2}O{sup +}) continue to increase throughout the process cycle. Using the m/e = 20 (D{sub 2}O{sup +}) peak intensity from chamber (1)–Cu(1.83 wt. %)Be as a standard, the peak intensity from chamber (4)—stainless-steel (air-fired) was 7.1× higher, indicating that the surface of stainless-steel had a larger concentration of reactive oxygen and/or water than hydrogen. The (D{sub 2}O{sup +}) peak intensity from chamber (3)—Cu (interior Al coating) was 1.55× larger and chamber (2)—alumina(99.8%) was 1.33× higher than Cu(1.83 wt. %)Be. Thus copper–(1.83 wt. %)beryllium was the best hydriding chamber material studied followed closely by the alumina (99.8 wt. %) chamber. Gas take-up by Er occluder targets processed in Cu(1.83 wt. %)Be hydriding chambers (i.e., gas/metal atomic ratios) correlate with the dynamic RGA data.« less

Blood cholinesterases as human biomarkers of organophosphorus pesticide exposure.

PubMed

Nigg, H N; Knaak, J B

2000-01-01

The organophosphorus pesticides of this review were discovered in 1936 during the search for a replacement for nicotine for cockroach control. The basic biochemical characteristics of RBC AChE and BChE were determined in the 1940s. The mechanism of inhibition of both enzymes and other serine esterases was known in the 1940s and, in general, defined in the 1950s. In 1949, the death of a parathion mixer-loader dictated blood enzyme monitoring to prevent acute illness from organophosphorus pesticide intoxication. However, many of the chemical and biochemical steps for serine enzyme inhibition by OP compounds remain unknown today. The possible mechanisms of this inhibition are presented kinetically beginning with simple (by comparison) Michaelis-Menten substrate enzyme interaction kinetics. As complicated as the inhibition kinetics appear here, PBPK model kinetics will be more complex. The determination of inter- and intraindividual variation in RBC ChE and BChE was recognized early as critical knowledge for a blood esterase monitoring program. Because of the relatively constant production of RBCs, variation in RBC AChE was determined by about 1970. The source of plasma (or serum) BChE was shown to be the liver in the 1960s with the change in BChE phenotype to the donor in liver transplant patients. BChE activity was more variable than RBC AChE, and only in the 1990s have BChE individual variation questions been answered. We have reviewed the chemistry, metabolism, and toxicity of organophosphorus insecticides along with their inhibitory action toward tissue acetyl- and butyrylcholinesterases. On the basis of the review, a monitoring program for individuals mixing-loading and applying OP pesticides for commercial applicators was recommended. Approximately 41 OPs are currently registered for use by USEPA in the United States. Under agricultural working conditions, OPs primarily are absorbed through the skin. Liver P-450 isozymes catalyze the desulfurization of phosphorothioates and phosphorodithioates (e.g., parathion and azinphosmethyl, respectively) to the more toxic oxons (P = O(S to O)). In some cases, P-450 isozymes catalyze the oxidative cleavage of P-O-aryl bonds (e.g., parathion, methyl parathion, fenitrothion, and diazinon) to form inactive water-soluble alkyl phosphates and aryl leaving groups that are readily conjugated with glucuronic or sulfuric acids and excreted. In addition to the P-450 isozymes, mammalian tissues contain ('A' and 'B') esterases capable of reacting with OPs to produce hydrolysis products or phosphorylated enzymes. 'A'-esterases hydrolyze OPs (i.e., oxons), while 'B'-esterases with serine at the active center are inhibited by OPs. OPs possessing carboxylesters, such as malathion and isofenphos, are hydrolyzed by the direct action of 'B'-esterases (i.e., carboxylesterase, CaE). Metabolic pathways shown for isofenphos, parathion, and malathion define the order in which these reactions occur, while Michaelis-Menten kinetics define reaction parameters (Vmax, K(m)) for the enzymes and substrates involved, and rates of inhibition of 'B'-esterases (kis, bimolecular rate constants) by OPs and their oxons. OPs exert their insecticidal action by their ability to inhibit AChE at the cholinergic synapse, resulting in the accumulation of acetylcholine. The extent to which AChE or other 'B'-esterases are inhibited in workers is dependent upon the rate the OP pesticide is activated (i.e., oxon formation), metabolized to nontoxic products by tissue enzymes, its affinity for AChE and other 'B'-esterases, and esterase concentrations in tissues. Rapid recovery of OP BChE inhibition may be related to reactivation of inhibited forms. AChE, BChE, and CaE appear to function in vivo as scavengers, protecting workers against the inhibition of AChE at synapses. Species sensitivity to OPs varies widely and results in part from binding affinities (Ka) and rates of phosphorylation (kp) rather than rates of activation and detoxif

A 400 year reconstruction of July relative air humidity for the region Vienna (eastern Austria) based on carbon and oxygen stable isotope ratios in tree-ring latewood cellulose of oaks

NASA Astrophysics Data System (ADS)

Haupt, M.; Boettger, T.; Weigl, M.; Grabner, M.

2009-04-01

Stable isotope chronologies and correlation to climate. We present the stable isotope chronologies of carbon (^13Clw) and oxygen (^18Olw) for the period from 1600 to 2003 respectively of non-exchangeable hydrogen (^2Hlw) for the last century constructed base upon tree-ring latewood cellulose from oaks (Quercus petraea Matt. Liebl.) grown in the region Vienna (Austria). The stable isotope ratios correspond mainly to the summer climate conditions. For the calibration period (1900-2003) we found high significant correlations (p < 0.001) between ^13Clw and relative air humidity (RH) of July (-0.66), between ^18Olw and RHV I-V II (-0.61) and between ^2Hlw and RHV I-V III(-0.56). In the case of temperatures high significant correlations between the growing season temperature and ^13Clw (0.55), between the annual mean temperatures and ^18Olw ratios (0.45) and between summer mean temperatures (June to August) and ^2Hlw values (0.49) were estimated. Modeling. Various univariate and multivariate linear regressions models were proved for the reconstruction of summer relative air humidity and temperature. We found that establishing of robust models had several uncertainties: - using common linear transfer functions which oversimplify the complexity of relations; - using of pooled material and neglecting of different reactions from individual trees to climate; - high-order autocorrelations in the isotope time series; - climatic trends in the investigated region which are different in the first and in the second half of 20th century; - temporal instability of climate signals in the isotope ratios of tree ring cellulose. In the case of temperature no valid model could be estimated caused by temporal instabilities of signal strength. For relative air humidity two bivariate models RHV II = (-4.3 ± 0.7) * ^13Clw + (-2.8 ± 0.5) * ^18Olw + 44 [1] and RHV II = (-4.7 ± 0.7) * ^13Clw + (-0.35 ± 0.07) * ^2Hlw - 68 [2] were found as verifiable and applicable to reconstruct RHV II. Using of ^2Hlw instead of ^18Olw enhances significantly the model verification. Unfortunately the data of non-exchangeable hydrogen were available only for the last 100 years. Therefore the reconstruction of July relative air humidity was carried out only with eq. [1]. Reconstruction. The predicted RHV II values oscillate in the period from 1600 to 2003 around a mean of 74.7±4.4%. The course of RHV II during this time seems to be periodic with wetting and drying periods in a cycle of approximately 130 years. Predominant wet conditions could be reconstructed for the periods 1690-1710, 1765-1820 and 1900-1960, predominant dry periods for the periods from 1715 to 1730, from 1830 to 1870 and from approximately 1960 to recent. These results correspond in general with the European Alpine moisture variability for the period 1800-2003 reported by van der Schrier et al. (2006). Extreme wet summer conditions could be reconstructed for 1663, 1795, 1816, 1906, 1915 and 1926. Exceptionally dry summers were supposed for 1616, 1636, 1637, 1751, 1822, 1857, 1863, 1990, 1992 and 2001. These results correspond to instrumental data and can be well verified by independent reconstructions (Glaser 2001; Casty et al. 2005). ACKNOWLEDGEMENTS This work was funded by EC grants EVK2-CT-2002-00147 (ISONET) and 017008 (GOCE; MILLENNIUM). REFERENCES Casty C, Wanner, H, Luterbacher J, Esper J, Böhm R (2005) Temperature and precipitation variability in the European Alps since 1500. Int J Climatol 25: 1855-1880. Fritts HC (1976) Tree-Rings and Climate. Academic Press Inc., London. Glaser R (2001) Klimageschichte Mitteleuropas. Wissenschaftliche Buchgesellschaft, Darmstadt. Rebetez M, Saurer M, Cherubini P (2003) To what extent can oxygen isotopes in tree rings and precipitation be used to reconstruct past atmospheric temperature? A case study. Climatic Change 61: 237-248. Treydte K, Frank D, Esper J, Andreu L, Bednarz Z, Berninger F, Boettger T, D'Allessandro CM, Etien N, Filot M, Grabner M, Guillemin MT, Gutierrez E, Haupt M, Helle G, Hilasvuori E, Jungner H, Kalela-Brundin M, Krapiec M, Leuenberger M, Loader NJ, Masson-Delmotte V, Pazdur A, Pawelczyk S, Pierre M, Planells O, Pukiene R, Reynolds-Henne CE, Rinne KT, Saracino A, Saurer M, Sonninen E, Stievenard M, Switsur VR, Szczepanek M, Szychowska-Krapiec E, Todaro L, Waterhouse JS, Weigl M, Schleser GH (2007) Signal strength and climate calibration of a European tree ring isotope network. Geophys Res Lett 34: L24302. van der Schrier G, Efthymiadis D, Briffa KR, Jones PD (2007) European Alpine moisture variability for 1900-2003. Int J Climatol 27: 415-427.

The ASC Sequoia Programming Model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seager, M

2008-08-06

In the late 1980's and early 1990's, Lawrence Livermore National Laboratory was deeply engrossed in determining the next generation programming model for the Integrated Design Codes (IDC) beyond vectorization for the Cray 1s series of computers. The vector model, developed in mid 1970's first for the CDC 7600 and later extended from stack based vector operation to memory to memory operations for the Cray 1s, lasted approximately 20 years (See Slide 5). The Cray vector era was deemed an extremely long lived era as it allowed vector codes to be developed over time (the Cray 1s were faster in scalarmore » mode than the CDC 7600) with vector unit utilization increasing incrementally over time. The other attributes of the Cray vector era at LLNL were that we developed, supported and maintained the Operating System (LTSS and later NLTSS), communications protocols (LINCS), Compilers (Civic Fortran77 and Model), operating system tools (e.g., batch system, job control scripting, loaders, debuggers, editors, graphics utilities, you name it) and math and highly machine optimized libraries (e.g., SLATEC, and STACKLIB). Although LTSS was adopted by Cray for early system generations, they later developed COS and UNICOS operating systems and environment on their own. In the late 1970s and early 1980s two trends appeared that made the Cray vector programming model (described above including both the hardware and system software aspects) seem potentially dated and slated for major revision. These trends were the appearance of low cost CMOS microprocessors and their attendant, departmental and mini-computers and later workstations and personal computers. With the wide spread adoption of Unix in the early 1980s, it appeared that LLNL (and the other DOE Labs) would be left out of the mainstream of computing without a rapid transition to these 'Killer Micros' and modern OS and tools environments. The other interesting advance in the period is that systems were being developed with multiple 'cores' in them and called Symmetric Multi-Processor or Shared Memory Processor (SMP) systems. The parallel revolution had begun. The Laboratory started a small 'parallel processing project' in 1983 to study the new technology and its application to scientific computing with four people: Tim Axelrod, Pete Eltgroth, Paul Dubois and Mark Seager. Two years later, Eugene Brooks joined the team. This team focused on Unix and 'killer micro' SMPs. Indeed, Eugene Brooks was credited with coming up with the 'Killer Micro' term. After several generations of SMP platforms (e.g., Sequent Balance 8000 with 8 33MHz MC32032s, Allian FX8 with 8 MC68020 and FPGA based Vector Units and finally the BB&N Butterfly with 128 cores), it became apparent to us that the killer micro revolution would indeed take over Crays and that we definitely needed a new programming and systems model. The model developed by Mark Seager and Dale Nielsen focused on both the system aspects (Slide 3) and the code development aspects (Slide 4). Although now succinctly captured in two attached slides, at the time there was tremendous ferment in the research community as to what parallel programming model would emerge, dominate and survive. In addition, we wanted a model that would provide portability between platforms of a single generation but also longevity over multiple--and hopefully--many generations. Only after we developed the 'Livermore Model' and worked it out in considerable detail did it become obvious that what we came up with was the right approach. In a nutshell, the applications programming model of the Livermore Model posited that SMP parallelism would ultimately not scale indefinitely and one would have to bite the bullet and implement MPI parallelism within the Integrated Design Code (IDC). We also had a major emphasis on doing everything in a completely standards based, portable methodology with POSIX/Unix as the target environment. We decided against specialized libraries like STACKLIB for performance, but kept as many general purpose, portable math libraries as were needed by the codes. Third, we assumed that the SMPs in clusters would evolve in time to become more powerful, feature rich and, in particular, offer more cores. Thus, we focused on OpenMP, and POSIX PThreads for programming SMP parallelism. These code porting efforts were lead by Dale Nielsen, A-Division code group leader, and Randy Christensen, B-Division code group leader. Most of the porting effort revolved removing 'Crayisms' in the codes: artifacts of LTSS/NLTSS, Civic compiler extensions beyond Fortran77, IO libraries and dealing with new code control languages (we switched to Perl and later to Python). Adding MPI to the codes was initially problematic and error prone because the programmers used MPI directly and sprinkled the calls throughout the code.« less

Modern Sorters for Soil Segregation on Large Scale Remediation Projects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shonka, J.J.; Kelley, J.E.; O'Brien, J.M.

2008-01-15

In the mid-1940's, Dr. C. Lapointe developed a Geiger tube based uranium ore scanner and picker to replace hand-cobbing. In the 1990's, a modern version of the Lapointe Picker for soil sorting was developed around the need to clean the Johnston Atoll of plutonium. It worked well with sand, but these systems are ineffective with soil, especially with wet conditions. Additionally, several other constraints limited throughput. Slow moving belts and thin layers of material on the belt coupled with the use of multiple small detectors and small sorting gates make these systems ineffective for high throughput. Soil sorting of clay-bearingmore » soils and building debris requires a new look at both the material handling equipment, and the radiation detection methodology. A new class of Super-Sorters has attained throughput of one hundred times that of the old designs. Higher throughput means shorter schedules which reduce costs substantially. The planning, cost, implementation, and other site considerations for these new Super-Sorters are discussed. Modern soil segregation was developed by Ed Bramlitt of the Defense Nuclear Agency for clean up at Johnston Atoll. The process eventually became the Segmented Gate System (SGS). This system uses an array of small sodium iodide (NaI) detectors, each viewing a small volume (segment), that control a gate. The volume in the gate is approximately one kg. This system works well when the material to be processed is sand; however, when the material is wet and sticky (soils with clays) the system has difficulty moving the material through the gates. Super-Sorters are a new class of machine designed to take advantage of high throughput aggregate processing conveyors, large acquisition volumes, and large NaI detectors using gamma spectroscopy. By using commercially available material handling equipment, the system can attain processing rates of up to 400 metric tons/hr with spectrum acquisition approximately every 0.5 sec, so the acquisition volume is 50 kilograms or less. Smaller sorting volumes can be obtained with lower throughput or by re-sorting the diverted material. This equipment can also handle large objects. The use of spectroscopy systems allows several regions of- interest to be set. Super-Sorters can bring waste processing charges down to less than $30/ metric ton on smaller jobs and can save hundreds of dollars per metric ton in disposal charges. The largest effect on the overall project cost occurs during planning and implementation. The overall goal is reduction of the length of the project, which dictates the most efficient soil processing. With all sorting systems the parameters that need to be accounted for are matrix type, soil feed rate, soil pre-processing, site conditions, and regulatory issues. The soil matrix and its ability to flow are extremely crucial to operations. It is also important to consider that as conditions change (i.e., moisture), the flowability of the soil matrix will change. Many soil parameters have to be considered: cohesive strength, internal and wall friction, permeability, and bulk density as a function of consolidating pressure. Clay bearing soils have very low permeability and high cohesive strength which makes them difficult to process, especially when wet. Soil feed speed is dependent on the equipment present and the ability to move the soil in the Super-Sorter processing area. When a Super-Sorter is running at 400 metric tons per hour it is difficult to feed the system. As an example, front-end loaders with large buckets would move approximately 5-10 metric tons of material, and 400 metric tons per hour would require 50-100 bucket-loads per hour to attain. Because the flowability of the soil matrix is important, poor material is often pre-processed before it is added to the feed hopper of the 'survey' conveyor. This pre-processing can consist of a 'grizzly' to remove large objects from the soil matrix, followed screening plant to prepare the soil so that it feeds well. Hydrated lime can be added to improve material properties. Site conditions (site area, typical weather conditions, etc.) also play a large part in project planning. Downtime lengthens project schedule and costs. The system must be configured to handle weather conditions or other variables that affect throughput. The largest single factor that plays into the project design is the regulatory environment. Before a sorter can be utilized, an averaging mass must be established by the regulator(s). There currently are no standards or guidelines in this area. The differences between acquisition mass and averaging mass are very important. The acquisition mass is defined based on the acquisition time and the geometry of the detectors. The averaging mass can then be as small as the acquisition mass or as large as several hundred tons (the averaging mass is simply the sum of a number of acquisitions). It is important to define volumetric limits and any required point-source limits. Super-Sorters handle both of these types of limits simultaneously. The minimum detectable activity for Super- Sorters is a function of speed. The chart below illustrates the detection confidence level for a 0.1 {mu}Ci point source of Ra-226 vs alarm point for three different sorter process rates. The minimal detection activity and diversion volume for a Super-Sorter is also a function of the acquisition mass. The curves were collected using a 0-15 kg acquisition mass. Diversion volumes ranged from 20-30 kg for a point source diversion. Soil Super-Sorters should be considered for every D and D project where it is desirable to reduce the waste stream. A volume reduction of 1:1000 can be gained for each pass through a modern sorter, resulting in significant savings in disposal costs.« less

Geology and mining history of the Southeast Missouri Barite District and the Valles Mines, Washington, Jefferson, and St. Francois Counties, Missouri

USGS Publications Warehouse

Mugel, Douglas N.

2017-03-09

The Southeast Missouri Barite District and the Valles Mines are located in Washington, Jefferson, and St. Francois Counties, Missouri, where barite and lead ore are present together in surficial and near-surface deposits. Lead mining in the area began in the early 1700’s and extended into the early 1900’s. Hand mining of lead in the residuum resulted in widespread pits (also called shafts or diggings), and there was some underground mining of lead in bedrock. By the 1860’s barite was recovered from the residuum by hand mining, also resulting in widespread diggings, but generally not underground mines in bedrock. Mechanized open-pit mining of the residuum for barite began in the 1920’s. Barite production slowed by the 1980’s, and there has not been any barite mining since 1998. Mechanized barite mining resulted in large mined areas and tailings ponds containing waste from barite mills.The U.S. Environmental Protection Agency (EPA) has determined that lead is present in surface soils in Washington and Jefferson Counties at concentrations exceeding health-based screening levels. Also, elevated concentrations of barium, arsenic, and cadmium have been identified in surface soils, and lead concentrations exceeding the Federal drinking-water standard of 15 micrograms per liter have been identified in private drinking-water wells. Potential sources of these contaminants are wastes associated with barite mining, wastes associated with lead mining, or unmined natural deposits of barium, lead, and other metals. As a first step in helping EPA determine the source of soil and groundwater contamination, the U.S. Geological Survey (USGS), in cooperation with the EPA, investigated the geology and mining history of the Southeast Missouri Barite District and the Valles Mines.Ore minerals are barite (barium sulfate), galena (lead sulfide), cerussite (lead carbonate), anglesite (lead sulfate), sphalerite (zinc sulfide), smithsonite (zinc carbonate), and chalcopyrite (copper-iron sulfide). The Cambrian Potosi Dolomite is the most important formation for the ore deposits, followed by the Eminence Dolomite. Because galena, sphalerite, and barite are less soluble than dolomite, chemical weathering of the ore-bearing dolomite bedrock resulted in the concentration of ore minerals in the residuum. Most of the barite and lead mining was in the residuum, which averages 10 to 15 feet thick.Lead mining by French explorers may have begun in 1719 along Old Mines Creek at Cabanage de Renaudiere, which was followed shortly by the discovery of lead and the development of lead mines at Mine Renault (also called Forche a Renault Mine), Old Mines, and at other places along the Big River, Mineral Fork, and Forche a Renault Creek. Lead mining began sometime between 1775 and 1780 at Mine a Breton, the name of which was later changed to Potosi. Other mining areas were developed in the early part of the 19th century, including Fourche a Courtois (Palmer Mines), the French Diggings, and the Richwoods Mines. Zinc became a valuable resource after the Civil War, and the Valles Mines was an important supplier of zinc as well as lead, with at least some production up until the 1920’s. Lead mining declined in the early part of the 20th century as mining in the Old Lead Belt, Mine La Motte, and the Tri-State District expanded.The earliest lead mines were diggings in the residuum and were round holes (shafts) about 4 feet in diameter dug with pick and shovel about 15–20 feet deep, with drifts dug a short distance laterally from the bottom of the shafts. This mining process was repeated a short distance away until a large area was covered with pits. Some mining in bedrock began by about 1800, with shafts as deep as 170 feet and as much as several hundred feet of lateral drifts.Smelting of the lead ore to elemental lead was first done using a log furnace, which was inefficient; estimates have been made that only about 50 percent of the lead was recovered, and the remainder was lost to the ashes (slags) and to volatilization. Starting in 1798, ash furnaces were used to smelt the ashes from the log furnaces. These two furnaces were worked in tandem for many years but were gradually replaced by other furnaces, including the Scotch hearth. Estimates of lead recovery as high as 80–90 percent have been made for the Scotch hearth. By the mid-1870’s the air furnace was being used, also with estimated lead recovery as high as 80–90 percent. Zinc furnaces were built when zinc became a valuable commodity, but much of the zinc ore was shipped out of the area, either to a smelter in St. Louis, Missouri, or to other smelters.The total lead and zinc production from the Southeast Missouri Barite District and the Valles Mines is estimated at 180,000 tons of lead and 60,000 tons of zinc. An estimated 97,000 tons of lead and an estimated 120,000 tons of zinc were lost during smelting. The estimated losses do not include losses at the mine site during mining and preparation for smelting, such as the loss of fine-grained galena during hand cleaning or the discarding of zinc ore before its value was known, for which no estimates are available.Hand mining for barite in the residuum was active by at least the 1860’s and peaked from 1905 to the 1930’s when several thousand people were engaged in barite mining. Hand mining (diggings) and cleaning of the ore was done in much the same way as earlier lead mining, with the additional use of a rattle box to further clean the barite. Mechanized open-pit mining of old barite diggings began in 1924 to recover barite left behind by hand mining, and washing plants were used to clean the clay from the barite. Hand mining, however, continued to thrive, and washer plants began to close temporarily in 1931; nearly all of the barite produced before 1937 was by hand mining. By the 1940’s, however, all barite mining was mechanized.Mechanized mining used shovels powered by steam, gasoline, or electricity (and by the 1950’s draglines and front-end loaders) to mine the residuum. The ore was loaded onto rail cars (and by the 1940’s, trucks) for shipment to washer plants. Clay was removed from the barite using a log washer, and a jig was used to concentrate the barite. Overflow from the log washers was waste and went to a mud (tailings) pond. The coarse jig tailings went to tailings piles or were used as railroad ballast and, later, to create roads within the mine pit. Some barite was ground, depending on its final use, and some ground barite was bleached using a hot solution of sulfuric acid to remove impurities such as iron minerals and lead sulfide (galena). An earlier bleaching process used lead-lined tanks.Large quantities of water were required for milling the barite; some was recirculated water and the remainder came from dammed streams or was pumped from wells. Tailings and wastewater were impounded behind dikes that were built across small valleys and were increased in height as necessary using washer waste and any overburden that had been stripped. In some cases, dikes were built across valleys that had already been mined for barite.The total production of barite from the Southeast Missouri Barite District and the Valles Mines is estimated to have been about 13.1 million tons. Most of the barite production was from Washington County. Hand mining and processing of barite was inefficient. Estimates of barite recovery range from less than one-fourth to about one-half because pillars between the shafts in the residuum needed to be left unmined for stability. With mechanized mining, large amounts of barite were lost during the milling process. It has been estimated that about 30 percent of the barite was lost and that about two-thirds of the lost barite was fine-grained and was discharged to the tailings ponds. Some galena was lost to the tailings ponds.A 1972 inventory of tailings ponds by the Missouri Geological Survey identified 67 ponds in the Southeast Missouri Barite District (there are more than this currently documented). Results from samples from four ponds that were drilled were used to estimate that the 67 ponds contained almost 39 million tons (or cubic yards) of tailings averaging about 5 percent barite, for a potential reserve of 1.935 million tons of barite.It is not known how much lead was removed during barite mining, either by hand or mechanized mining and processing, how much lead was recovered, or how much lead went as fines to the tailing ponds or as coarse material to mine roads or was otherwise lost.