Localized Multi-Model Extremes Metrics for the Fourth National Climate Assessment

NASA Astrophysics Data System (ADS)

Thompson, T. R.; Kunkel, K.; Stevens, L. E.; Easterling, D. R.; Biard, J.; Sun, L.

2017-12-01

We have performed localized analysis of scenario-based datasets for the Fourth National Climate Assessment (NCA4). These datasets include CMIP5-based Localized Constructed Analogs (LOCA) downscaled simulations at daily temporal resolution and 1/16th-degree spatial resolution. Over 45 temperature and precipitation extremes metrics have been processed using LOCA data, including threshold, percentile, and degree-days calculations. The localized analysis calculates trends in the temperature and precipitation extremes metrics for relatively small regions such as counties, metropolitan areas, climate zones, administrative areas, or economic zones. For NCA4, we are currently addressing metropolitan areas as defined by U.S. Census Bureau Metropolitan Statistical Areas. Such localized analysis provides essential information for adaptation planning at scales relevant to local planning agencies and businesses. Nearly 30 such regions have been analyzed to date. Each locale is defined by a closed polygon that is used to extract LOCA-based extremes metrics specific to the area. For each metric, single-model data at each LOCA grid location are first averaged over several 30-year historical and future periods. Then, for each metric, the spatial average across the region is calculated using model weights based on both model independence and reproducibility of current climate conditions. The range of single-model results is also captured on the same localized basis, and then combined with the weighted ensemble average for each region and each metric. For example, Boston-area cooling degree days and maximum daily temperature is shown below for RCP8.5 (red) and RCP4.5 (blue) scenarios. We also discuss inter-regional comparison of these metrics, as well as their relevance to risk analysis for adaptation planning.

APT Blanket System Loss-of-Coolant Accident (LOCA) Based on Initial Conceptual Design - Case 2: with Beam Shutdown Only

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamm, L.L.

1998-10-07

This report is one of a series of reports that document normal operation and accident simulations for the Accelerator Production of Tritium (APT) blanket heat removal system. These simulations were performed for the Preliminary Safety Analysis Report. This report documents the results of simulations of a Loss-of-Flow Accident (LOFA) where power is lost to all of the pumps that circulate water in the blanket region, the accelerator beam is shut off and neither the residual heat removal nor cavity flood systems operate.

SPES-2, an experimental program to support the AP600 development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tarantini, M.; Medich, C.

1995-09-01

In support of the development of the AP600 reactor, ENEA, ENEL, ANSALDO and Westinghouse have signed a research agreement. In the framework of this agreement a complex Full Height Full Pressure (FHFP) integral system testing program has been planned on SPES-2 facility. The main purpose of this paper is to point out the status of the test program; describe the hot per-operational test performed and the complete test matrix, giving all the necessary references on the work already published. Two identical Small Break LOCA transients, performed with Pressurizer to Core Make-up Tank (PRZ-CMT) balance line (Test S00203) and without PRZ-CMTmore » balance line (Test S00303) are then compared, to show how the SPES-2 facility can contribute in confirming the new AP600 reactor design choices and can give useful indications to designers. Although the detailed analysis of test data has not been completed, some consideration on the analytical tools utilized and on the SPES-2 capability to simulate the reference plant is then drawn.« less

R&D Plan for RISMC Industry Application #1: ECCS/LOCA Cladding Acceptance Criteria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szilard, Ronaldo Henriques; Zhang, Hongbin; Epiney, Aaron Simon

The Nuclear Regulatory Commission (NRC) is finalizing a rulemaking change that would revise the requirements in 10 CFR 50.46. In the proposed new rulemaking, designated as 10 CFR 50.46c, the NRC proposes a fuel performance-based equivalent cladding reacted (ECR) criterion as a function of cladding hydrogen content before the accident (pre-transient) in order to include the effects of higher burnup on cladding performance as well as to address other technical issues. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licenseemore » costs as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. The Idaho National Laboratory (INL) has initiated a project, as part of the DOE Light Water Reactor Sustainability Program (LWRS), to develop analytical capabilities to support the industry in the transition to the new rule. This project is called the Industry Application 1 (IA1) within the Risk-Informed Safety Margin Characterization (RISMC) Pathway of LWRS. The general idea behind the initiative is the development of an Integrated Evaluation Model (IEM). The motivation is to develop a multiphysics framework to analyze how uncertainties are propagated across the stream of physical disciplines and data involved, as well as how risks are evaluated in a LOCA safety analysis as regulated under 10 CFR 50.46c. This IEM is called LOTUS which stands for LOCA Toolkit for US, and it represents the LWRS Program’s response to the proposed new rule making. The focus of this report is to complete an R&D plan to describe the demonstration of the LOCA/ECCS RISMC Industry Application # 1 using the advanced RISMC Toolkit and methodologies. This report includes the description and development plan for a RISMC LOCA tool that fully couples advanced MOOSE tools already in development in order to characterize and optimize plant safety and operational margins. Advanced MOOSE tools that are needed to complete this integrated evaluation model are: RAVEN, RELAP-7, BISON, and MAMMOTH.« less

Core cooling under accident conditions at the high-flux beam reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tichler, P.; Cheng, L.; Fauske, H.

The High-Flux Beam Reactor (HFBR) at Brookhaven National Laboratory (BNL) is cooled and moderated by heavy water and contains {sup 235}U in the form of narrow-channel, parallel-plate-type fuel elements. During normal operation, the flow direction is downward through the core. This flow direction is maintained at a reduced flow rate during routine shutdown and on loss of commercial power by means of redundant pumps and power supplies. However, in certain accident scenarios, e.g. loss-of-coolant accidents (LOCAs), all forced-flow cooling is lost. Although there was experimental evidence during the reactor design period (1958-1963) that the heat removal capacity in the fullymore » developed natural circulation cooling mode was relatively high, it was not possible to make a confident prediction of the heat removal capacity during the transition from downflow to natural circulation. Accordingly, a test program was initiated using an electrically heated section to simulate the fuel channel and a cooling loop to simulate the balance of the primary cooling system.« less

Manpower Requirements Report for FY 1982

DTIC Science & Technology

1981-02-01

Specifically included are program elements for industrial preparedness, second destination transportation, property disposal, production engineering ...artillery, and combat - engineers . Army policy accepts the fact that women will serve in loca- .. tions throughout the battlefield, will be expected to... industrial engineering work measurement techniques and computerized models such as the Logistics Composite Model (LCOM). MEP policy emanates from the

JPRS Report Science & Technology Japan

DTIC Science & Technology

1989-03-02

Oxychlorides MOCln_2 (Organic Metal Salts) Alkoxides M(OR)n Acetylacetonate M(C5H702)n Acetates M(C2H302)n Oxalates M(C204)n/2 2.2 Hydrolysis and Gel...more deeply understanding hydrothermal dynamics during not only a major rupture LOCA but also a minor rupture LOCA and clarifying the combination of... hydrothermal dynamics of the coolant from the beginning of LOCA to its end, using a scale model of PWR (pressurized water reactor). Under the ROSA-III Plan

Decay Heat Removal from a GFR Core by Natural Convection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Wesley C.; Hejzlar, Pavel; Driscoll, Michael J.

2004-07-01

One of the primary challenges for Gas-cooled Fast Reactors (GFR) is decay heat removal after a loss of coolant accident (LOCA). Due to the fact that thermal gas cooled reactors currently under design rely on passive mechanisms to dissipate decay heat, there is a strong motivation to accomplish GFR core cooling through natural phenomena. This work investigates the potential of post-LOCA decay heat removal from a GFR core to a heat sink using an external convection loop. A model was developed in the form of the LOCA-COLA (Loss of Coolant Accident - Convection Loop Analysis) computer code as a meansmore » for 1D steady state convective heat transfer loop analysis. The results show that decay heat removal by means of gas cooled natural circulation is feasible under elevated post-LOCA containment pressure conditions. (authors)« less

Loss of Coolant Accident (LOCA) / Emergency Core Coolant System (ECCS Evaluation of Risk-Informed Margins Management Strategies for a Representative Pressurized Water Reactor (PWR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szilard, Ronaldo Henriques

A Risk Informed Safety Margin Characterization (RISMC) toolkit and methodology are proposed for investigating nuclear power plant core, fuels design and safety analysis, including postulated Loss-of-Coolant Accident (LOCA) analysis. This toolkit, under an integrated evaluation model framework, is name LOCA toolkit for the US (LOTUS). This demonstration includes coupled analysis of core design, fuel design, thermal hydraulics and systems analysis, using advanced risk analysis tools and methods to investigate a wide range of results.

Risk-Informed Margin Management (RIMM) Industry Applications IA1 - Integrated Cladding ECCS/LOCA Performance Analysis - Problem Statement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szilard, Ronaldo Henriques; Youngblood, Robert; Frepoli, Cesare

2015-04-01

The U. S. NRC is currently proposing rulemaking designated as “10 CFR 50.46c” to revise the LOCA/ECCS acceptance criteria to include the effects of higher burnup on cladding performance as well as to address some other issues. The NRC is also currently resolving the public comments with the final rule expected to be issued in the summer of 2016. The impact of the final 50.46c rule on the industry will involve updating of fuel vendor LOCA evaluation models, NRC review and approval, and licensee submittal of new LOCA evaluations or reanalyses and associated technical specification revisions for NRC review andmore » approval. The rule implementation process, both industry and NRC activities, is expected to take 5-10 years following the rule effective date. The need to use advanced cladding designs is expected. A loss of operational margin will result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin.« less

Diagnostics of Loss of Coolant Accidents Using SVC and GMDH Models

NASA Astrophysics Data System (ADS)

Lee, Sung Han; No, Young Gyu; Na, Man Gyun; Ahn, Kwang-Il; Park, Soo-Yong

2011-02-01

As a means of effectively managing severe accidents at nuclear power plants, it is important to identify and diagnose accident initiating events within a short time interval after the accidents by observing the major measured signals. The main objective of this study was to diagnose loss of coolant accidents (LOCAs) using artificial intelligence techniques, such as SVC (support vector classification) and GMDH (group method of data handling). In this study, the methodologies of SVC and GMDH models were utilized to discover the break location and estimate the break size of the LOCA, respectively. The 300 accident simulation data (based on MAAP4) were used to develop the SVC and GMDH models, and the 33 test data sets were used to independently confirm whether or not the SVC and GMDH models work well. The measured signals from the reactor coolant system, steam generators, and containment at a nuclear power plant were used as inputs to the models, and the 60 sec time-integrated values of the input signals were used as inputs into the SVC and GMDH models. The simulation results confirmed that the proposed SVC model can identify the break location and the proposed GMDH models can estimate the break size accurately. In addition, even if the measurement errors exist and safety systems actuate, the proposed SVC and GMDH models can discover the break locations without a misclassification and accurately estimate the break size.

Hydrogen motion in Zircaloy-4 cladding during a LOCA transient

NASA Astrophysics Data System (ADS)

Elodie, T.; Jean, D.; Séverine, G.; M-Christine, B.; Michel, C.; Berger, P.; Martine, B.; Antoine, A.

2016-04-01

Hydrogen and oxygen are key elements influencing the embrittlement of zirconium-based nuclear fuel cladding during the quench phase following a Loss Of Coolant Accident (LOCA). The understanding of the mechanisms influencing the motion of these two chemical elements in the metal is required to fully describe the material embrittlement. High temperature steam oxidation tests were performed on pre-hydrided Zircaloy-4 samples with hydrogen contents ranging between 11 and 400 wppm prior to LOCA transient. Thanks to the use of both Electron Probe Micro-Analysis (EPMA) and Elastic Recoil Detection Analysis (μ-ERDA), the chemical elements partitioning has been systematically quantified inside the prior-β phase. Image analysis and metallographic examinations were combined to provide an average oxygen profile as well as hydrogen profile within the cladding thickness after LOCA transient. The measured hydrogen profile is far from homogeneous. Experimental distributions are compared to those predicted numerically using calculations derived from a finite difference thermo-diffusion code (DIFFOX) developed at IRSN.

Joint Force Quarterly. Number 15, Spring 1997

DTIC Science & Technology

1997-06-01

headquarters to extract information from sensors on the vehicle without bothering crew members with extraneous reports. Position loca- tion devices on... change in how they do business. Air Force lean logistics and Army velocity management programs are literal springboards for quantum improvements in...Spring 1997 Victory smiles upon those who anticipate the changes in the character of war, not upon those who wait to adapt themselves after the changes

Beam Research Program

DTIC Science & Technology

1984-04-01

wavelengths. A direct application of such a laser is isotope separation. 2. For a brief status report of the Laboratory’s high- explosive flash...operation in the fall of 1982. in a 50-MeV Advanced Test Accelerator Facility (the ATA)1 that we are con- structing at our high- explosives test loca...chemical explosives in target-damage studies. Potential hazards associated with the ATA experiments were considered in choosing our site. LLNL’s

Spatializing Sexuality in Jaime Hernandez's "Locas"

ERIC Educational Resources Information Center

Jones, Jessica E.

2009-01-01

Focusing on Jaime Hernandez's "Locas: The Maggie and Hopey Stories," part of the "Love and Rockets" comic series, I argue that the graphic landscape of this understudied comic offers an illustration of the theories of space in relation to race, gender, and sexuality that have been critical to understandings of Chicana…

75 FR 53985 - Arizona Public Service Company, et al., Palo Verde Nuclear Generating Station, Unit 3; Temporary...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-02

... are authorized by law, will not present an undue risk to public health or safety, and are consistent... Public Health and Safety The underlying purpose of 10 CFR 50.46 is to establish acceptance criteria for... (LOCA) and non-LOCA criteria, mechanical design, thermal hydraulics, seismic, core physics, and...

75 FR 8139 - Biweekly Notice; Applications and Amendments to Facility Operating Licenses Involving No...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-23

... the large break loss-of-coolant accident (LOCA) analysis methodology with a reference to WCAP-16009-P... required by 10 CFR 50.91(a), the licensee has provided its analysis of the issue of no significant hazards... Section 5.6.5 to incorporate a new large break LOCA analysis methodology. Specifically, the proposed...

Parameter study on the influence of prepressurization on PWR fuel rod behavior during normal operation and hypothetical LOCAs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brzoska, B.; Depisch, F.; Fuchs, H.P.

To analyze the influence of prepressurization on fuel rod behavior, a parametric study has been performed that considers the effects of as-fabricated fuel rod internal prepressure on the normal operation and postulated loss-of-coolant accident (LOCA) rod behavior of a 1300-MW(electric) Kraftwerk Union (KWU) standard pressurized water reactor nuclear power plant. A variation of the prepressure in the range from 15 to 35 bars has only a slight influence on normal operation behavior. Considering the LOCA behavior, only a small temperature increase results from prepressure reduction, while the core-wide straining behavior is improved significantly. The KWU prepressurization takes both conditions intomore » account.« less

Pressure suppression system

DOEpatents

Gluntz, D.M.

1994-10-04

A pressure suppression system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and an enclosed gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The GDCS pool includes a plenum for receiving through an inlet the non-condensable gas carried with steam from the drywell following a loss-of-coolant accident (LOCA). A condenser is disposed in the GDCS plenum for condensing the steam channeled therein and to trap the non-condensable gas therein. A method of operation includes draining the GDCS pool following the LOCA and channeling steam released into the drywell following the LOCA into the GDCS plenum for cooling along with the non-condensable gas carried therewith for trapping the gas therein. 3 figs.

Pressure suppression system

DOEpatents

Gluntz, Douglas M.

1994-01-01

A pressure suppression system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and an enclosed gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The GDCS pool includes a plenum for receiving through an inlet the non-condensable gas carried with steam from the drywell following a loss-of-coolant accident (LOCA). A condenser is disposed in the GDCS plenum for condensing the steam channeled therein and to trap the non-condensable gas therein. A method of operation includes draining the GDCS pool following the LOCA and channeling steam released into the drywell following the LOCA into the GDCS plenum for cooling along with the non-condensable gas carried therewith for trapping the gas therein.

RELAP5/MOD2 analysis of a postulated cold leg SBLOCA'' simultaneous to a total black-out'' event in the Jose Cabrera Nuclear Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebollo, L.

1992-04-01

Several beyond-design bases cold leg small-break LOCA postulated scenarios based on the lessons learned'' in the OECD-LOFT LP-SB-3 experiment have been analyzed for the Westinghouse single loop Jose Cabrera Nuclear Power Plant belonging to the Spanish utility UNION ELECTRICA FENOSA, S.A. The analysis has been done by the utility in the Thermal-Hydraulic Accident Analysis Section of the Engineering Department of the Nuclear Division. The RELAP5/MOD2/36.04 code has been used on a CYBER 180/830 computer and the simulation includes the 6 in. RHRS charging line, the 2 in. pressurizer spray, and the 1.5 in. CVCS make-up line piping breaks. The assumptionmore » of a total black-out condition'' coincident with the occurrence of the event has been made in order to consider a plant degraded condition with total active failure of the ECCS. As a result of the analysis, estimates of the time to core overheating startup'' as well as an evaluation of alternate operator measures to mitigate the consequences of the event have been obtained. Finally a proposal for improving the LOCA emergency operating procedure (E-1) has been suggested.« less

RELAP5/MOD2 analysis of a postulated ``cold leg SBLOCA`` simultaneous to a ``total black-out`` event in the Jose Cabrera Nuclear Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rebollo, L.

1992-04-01

Several beyond-design bases cold leg small-break LOCA postulated scenarios based on the ``lessons learned`` in the OECD-LOFT LP-SB-3 experiment have been analyzed for the Westinghouse single loop Jose Cabrera Nuclear Power Plant belonging to the Spanish utility UNION ELECTRICA FENOSA, S.A. The analysis has been done by the utility in the Thermal-Hydraulic & Accident Analysis Section of the Engineering Department of the Nuclear Division. The RELAP5/MOD2/36.04 code has been used on a CYBER 180/830 computer and the simulation includes the 6 in. RHRS charging line, the 2 in. pressurizer spray, and the 1.5 in. CVCS make-up line piping breaks. Themore » assumption of a ``total black-out condition`` coincident with the occurrence of the event has been made in order to consider a plant degraded condition with total active failure of the ECCS. As a result of the analysis, estimates of the ``time to core overheating startup`` as well as an evaluation of alternate operator measures to mitigate the consequences of the event have been obtained. Finally a proposal for improving the LOCA emergency operating procedure (E-1) has been suggested.« less

TRAC-PF1 code verification with data from the OTIS test facility. [Once-Through Intergral System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Childerson, M.T.; Fujita, R.K.

1985-01-01

A computer code (TRAC-PF1/MOD1) developed for predicting transient thermal and hydraulic integral nuclear steam supply system (NSSS) response was benchmarked. Post-small break loss-of-coolant accident (LOCA) data from a scaled, experimental facility, designated the One-Through Integral System (OTIS), were obtained for the Babcock and Wilcox NSSS and compared to TRAC predictions. The OTIS tests provided a challenging small break LOCA data set for TRAC verification. The major phases of a small break LOCA observed in the OTIS tests included pressurizer draining and loop saturation, intermittent reactor coolant system circulation, boiler-condenser mode, and the initial stages of refill. The TRAC code wasmore » successful in predicting OTIS loop conditions (system pressures and temperatures) after modification of the steam generator model. In particular, the code predicted both pool and auxiliary-feedwater initiated boiler-condenser mode heat transfer.« less

Implementation of non-condensable gases condensation suppression model into the WCOBRA/TRAC-TF2 LOCA safety evaluation code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, J.; Cao, L.; Ohkawa, K.

2012-07-01

The non-condensable gases condensation suppression model is important for a realistic LOCA safety analysis code. A condensation suppression model for direct contact condensation was previously developed by Westinghouse using first principles. The model is believed to be an accurate description of the direct contact condensation process in the presence of non-condensable gases. The Westinghouse condensation suppression model is further revised by applying a more physical model. The revised condensation suppression model is thus implemented into the WCOBRA/TRAC-TF2 LOCA safety evaluation code for both 3-D module (COBRA-TF) and 1-D module (TRAC-PF1). Parametric study using the revised Westinghouse condensation suppression model ismore » conducted. Additionally, the performance of non-condensable gases condensation suppression model is examined in the ACHILLES (ISP-25) separate effects test and LOFT L2-5 (ISP-13) integral effects test. (authors)« less

Pressure suppression containment system

DOEpatents

Gluntz, Douglas M.; Townsend, Harold E.

1994-03-15

A pressure suppression containment system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The wetwell pool includes a plenum for receiving the non-condensable gas carried with steam from the drywell following a loss-of coolant-accident (LOCA). The wetwell plenum is vented to a plenum above the GDCS pool following the LOCA for suppressing pressure rise within the containment vessel. A method of operation includes channeling steam released into the drywell following the LOCA into the wetwell pool for cooling along with the non-condensable gas carried therewith. The GDCS pool is then drained by gravity, and the wetwell plenum is vented into the GDCS plenum for channeling the non-condensable gas thereto.

Pressure suppression containment system

DOEpatents

Gluntz, D.M.; Townsend, H.E.

1994-03-15

A pressure suppression containment system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel. The wetwell pool includes a plenum for receiving the non-condensable gas carried with steam from the drywell following a loss-of-coolant-accident (LOCA). The wetwell plenum is vented to a plenum above the GDCS pool following the LOCA for suppressing pressure rise within the containment vessel. A method of operation includes channeling steam released into the drywell following the LOCA into the wetwell pool for cooling along with the non-condensable gas carried therewith. The GDCS pool is then drained by gravity, and the wetwell plenum is vented into the GDCS plenum for channeling the non-condensable gas thereto. 6 figures.

BESAFE II: Accident safety analysis code for MFE reactor designs

NASA Astrophysics Data System (ADS)

Sevigny, Lawrence Michael

The viability of controlled thermonuclear fusion as an alternative energy source hinges on its desirability from an economic and an environmental and safety standpoint. It is the latter which is the focus of this thesis. For magnetic fusion energy (MFE) devices, the safety concerns equate to a design's behavior during a worst-case accident scenario which is the loss of coolant accident (LOCA). In this dissertation, we examine the behavior of MFE devices during a LOCA and how this behavior relates to the safety characteristics of the machine; in particular the acute, whole-body, early dose. In doing so, we have produced an accident safety code, BESAFE II, now available to the fusion reactor design community. The Appendix constitutes the User's Manual for BESAFE II. The theory behind early dose calculations including the mobilization of activation products is presented in Chapter 2. Since mobilization of activation products is a strong function of temperature, it becomes necessary to calculate the thermal response of a design during a LOCA in order to determine the fraction of the activation products which are mobilized and thus become the source for the dose. The code BESAFE II is designed to determine the temperature history of each region of a design and determine the resulting mobilization of activation products at each point in time during the LOCA. The BESAFE II methodology is discussed in Chapter 4, followed by demonstrations of its use for two reference design cases: a PCA-Li tokamak and a SiC-He tokamak. Of these two cases, it is shown that the SiC-He tokamak is a better design from an accident safety standpoint than the PCA-Li tokamak. It is also found that doses derived from temperature-dependent mobilization data are different than those predicted using set mobilization categories such as those that involve Piet fractions. This demonstrates the need for more experimental data on fusion materials. The possibility for future improvements and modifications to BESAFE II is discussed in Chapter 6, for example, by adding additional environmental indices such as a waste disposal index. The biggest improvement to BESAFE II would be an increase in the database of activation product mobilization for a larger spectrum of fusion reactor materials. The ultimate goal we have is for BESAFE II to become part of a systems design program which would include economic factors and allow both safety and the cost of electricity to influence design.

In-pile tests at Karlsruhe of LWR fuel-rod behavior during the heatup phase of a LOCA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karb, E.H.

1980-01-01

In order to investigate the influence of a nuclar environment on the mechanisms of fuel-rod failure, in-pile tests simulating the heatup phase of a loss-of-coolant accident in a pressurized-water reactor are being conducted with irradiated and unirradiated short-length single rods in the FR2 reactor at Kernforschungszentrum karlsruhe (Karlsruhe Nuclear Reasearch Center), Federal Republic of Germany, within the Project Nuclear Safety. With nearly 70% of the scheduled tests completed, no such influences have been found. The in-pile burst and deformation data are in good agreement with results from nonnuclear tests with electrically heated fuel-rod simulators. The phenomenon of pellet disintegration, whichmore » has been observed in all tests with previously irradiated rods, needs further investigation.« less

Industry Application Emergency Core Cooling System Cladding Acceptance Criteria Early Demonstration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szilard, Ronaldo H.; Youngblood, Robert W.; Zhang, Hongbin

2015-09-01

The U. S. NRC is currently proposing rulemaking designated as “10 CFR 50.46c” to revise the loss-of-coolant-accident (LOCA)/emergency core cooling system (ECCS) acceptance criteria to include the effects of higher burnup on cladding performance as well as to address other technical issues. The NRC is also currently resolving the public comments with the final rule expected to be issued in April 2016. The impact of the final 50.46c rule on the industry may involve updating of fuel vendor LOCA evaluation models, NRC review and approval, and licensee submittal of new LOCA evaluations or re-analyses and associated technical specification revisions formore » NRC review and approval. The rule implementation process, both industry and NRC activities, is expected to take 4-6 years following the rule effective date. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The proposed rule would apply to a light water reactor and to all cladding types.« less

Experimental study of Siphon breaker about size effect in real scale reactor design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, S. H.; Ahn, H. S.; Kim, J. M.

2012-07-01

Rupture accident within the pipe of a nuclear reactor is one of the main causes of a loss of coolant accident (LOCA). Siphon-breaking is a passive method that can prevent a LOCA. In this study, either a line or a hole is used as a siphon-breaker, and the effect of various parameters, such as the siphon-breaker size, pipe rupture point, pipe rupture size, and the presence of an orifice, are investigated using an experimental facility similar in size to a full-scale reactor. (authors)

The Future of Drought in the Southeastern U.S.: Projections from downscaled CMIP5 models

NASA Astrophysics Data System (ADS)

Keellings, D.; Engstrom, J.

2017-12-01

The Southeastern U.S. has been repeatedly impacted by severe droughts that have affected the environment and economy of the region. In this study the ability of 32 downscaled CMIP5 models, bias corrected using localized constructed analogs (LOCA), to simulate historical observations of dry spells from 1950-2005 are assessed using Perkins skill scores and significance tests. The models generally simulate the distribution of dry days well but there are significant differences between the ability of the best and worst performing models, particularly when it comes to the upper tail of the distribution. The best and worst performing models are then projected through 2099, using RCP 4.5 and 8.5, and estimates of 20 year return periods are compared. Only the higher skill models provide a good estimate of extreme dry spell lengths with simulations of 20 year return values within ± 5 days of observed values across the region. Projected return values differ by model grouping, but all models exhibit significant increases.

Preliminary phenomena identification and ranking tables for simplified boiling water reactor Loss-of-Coolant Accident scenarios

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kroeger, P.G.; Rohatgi, U.S.; Jo, J.H.

1998-04-01

For three potential Loss-of-Coolant Accident (LOCA) scenarios in the General Electric Simplified Boiling Water Reactors (SBWR) a set of Phenomena Identification and Ranking Tables (PIRT) is presented. The selected LOCA scenarios are typical for the class of small and large breaks generally considered in Safety Analysis Reports. The method used to develop the PIRTs is described. Following is a discussion of the transient scenarios, the PIRTs are presented and discussed in detailed and in summarized form. A procedure for future validation of the PIRTs, to enhance their value, is outlined. 26 refs., 25 figs., 44 tabs.

TRAC analyses for CCTF and SCTF tests and UPTF design/operation. [Cylindrical Core Test Facility; Slab Core Test Facility; Upper Plenum Test Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spore, J.W.; Cappiello, M.W.; Dotson, P.J.

The analytical support in 1985 for Cylindrical Core Test Facility (CCTF), Slab Core Test Facility (SCTF), and Upper Plenum Test Facility (UPTF) tests involves the posttest analysis of 16 tests that have already been run in the CCTF and the SCTF and the pretest analysis of 3 tests to be performed in the UPTF. Posttest analysis is used to provide insight into the detailed thermal-hydraulic phenomena occurring during the refill and reflood tests performed in CCTF and SCTF. Pretest analysis is used to ensure that the test facility is operated in a manner consistent with the expected behavior of anmore » operating full-scale plant during an accident. To obtain expected behavior of a plant during an accident, two plant loss-of-coolant-accident (LOCA) calculations were performed: a 200% cold-leg-break LOCA calculation for a 2772 MW(t) Babcock and Wilcox plant and a 200% cold-leg-break LOCA calculation for a 3315 MW(t) Westinghouse plant. Detailed results are presented for several CCTF UPI tests and the Westinghouse plant analysis.« less

Experimental investigation on circumferential and axial temperature gradient over fuel channel under LOCA

NASA Astrophysics Data System (ADS)

Yadav, Ashwini Kumar; kumar, Ravi; Gupta, Akhilesh; Chatterjee, Barun; Mukhopadhyay, Deb; Lele, H. G.

2014-06-01

In a nuclear reactor temperature rises drastically in fuel channels under loss of coolant accident due to failure of primary heat transportation system. Present investigation has been carried out to capture circumferential and axial temperature gradients during fully and partially voiding conditions in a fuel channel using 19 pin fuel element simulator. A series of experiments were carried out by supplying power to outer, middle and center rods of 19 pin fuel simulator in ratio of 1.4:1.1:1. The temperature at upper periphery of pressure tube (PT) was slightly higher than at bottom due to increase in local equivalent thermal conductivity from top to bottom of PT. To simulate fully voided conditions PT was pressurized at 2.0 MPa pressure with 17.5 kW power injection. Ballooning initiated from center and then propagates towards the ends and hence axial temperature difference has been observed along the length of PT. For asymmetric heating, upper eight rods of fuel simulator were activated and temperature difference up-to 250 °C has been observed from top to bottom periphery of PT. Such situation creates steep circumferential temperature gradient over PT and could lead to breaching of PT under high pressure.

Public Response to a Near-Miss Nuclear Accident Scenario Varying in Causal Attributions and Outcome Uncertainty.

PubMed

Cui, Jinshu; Rosoff, Heather; John, Richard S

2018-05-01

Many studies have investigated public reactions to nuclear accidents. However, few studies focused on more common events when a serious accident could have happened but did not. This study evaluated public response (emotional, cognitive, and behavioral) over three phases of a near-miss nuclear accident. Simulating a loss-of-coolant accident (LOCA) scenario, we manipulated (1) attribution for the initial cause of the incident (software failure vs. cyber terrorist attack vs. earthquake), (2) attribution for halting the incident (fail-safe system design vs. an intervention by an individual expert vs. a chance coincidence), and (3) level of uncertainty (certain vs. uncertain) about risk of a future radiation leak after the LOCA is halted. A total of 773 respondents were sampled using a 3 × 3 × 2 between-subjects design. Results from both MANCOVA and structural equation modeling (SEM) indicate that respondents experienced more negative affect, perceived more risk, and expressed more avoidance behavioral intention when the near-miss event was initiated by an external attributed source (e.g., earthquake) compared to an internally attributed source (e.g., software failure). Similarly, respondents also indicated greater negative affect, perceived risk, and avoidance behavioral intentions when the future impact of the near-miss incident on people and the environment remained uncertain. Results from SEM analyses also suggested that negative affect predicted risk perception, and both predicted avoidance behavior. Affect, risk perception, and avoidance behavior demonstrated high stability (i.e., reliability) from one phase to the next. © 2017 Society for Risk Analysis.

Thermal-hydraulic modeling needs for passive reactors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, J.M.

1997-07-01

The U.S. Nuclear Regulatory Commission has received an application for design certification from the Westinghouse Electric Corporation for an Advanced Light Water Reactor design known as the AP600. As part of the design certification process, the USNRC uses its thermal-hydraulic system analysis codes to independently audit the vendor calculations. The focus of this effort has been the small break LOCA transients that rely upon the passive safety features of the design to depressurize the primary system sufficiently so that gravity driven injection can provide a stable source for long term cooling. Of course, large break LOCAs have also been considered,more » but as the involved phenomena do not appear to be appreciably different from those of current plants, they were not discussed in this paper. Although the SBLOCA scenario does not appear to threaten core coolability - indeed, heatup is not even expected to occur - there have been concerns as to the performance of the passive safety systems. For example, the passive systems drive flows with small heads, consequently requiring more precision in the analysis compared to active systems methods for passive plants as compared to current plants with active systems. For the analysis of SBLOCAs and operating transients, the USNRC uses the RELAP5 thermal-hydraulic system analysis code. To assure the applicability of RELAP5 to the analysis of these transients for the AP600 design, a four year long program of code development and assessment has been undertaken.« less

Core cooling under accident conditions at the high flux beam reactor (HFBR)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tichler, P.; Cheng, L.; Fauske, H.

In certain accident scenarios, e.g. loss of coolant accidents (LOCA) all forced flow cooling is lost. Decay heating causes a temperature increase in the core coolant and the resulting thermal buoyancy causes a reversal of the flow direction to a natural circulation mode. Although there was experimental evidence during the reactor design period (1958--1963) that the heat removal capacity in the fully developed natural circulation cooling mode was relatively high, it was not possible to make a confident prediction of the heat removal capacity during the transition from downflow to natural circulation. In a LOCA scenario where even limited fuelmore » damage occurs and natural circulation is established, fission product gases could be carried from the damaged fuel by steam into areas where operator access is required to maintain the core in a coolable configuration. This would force evacuation of the building and lead to extensive core damage. As a result the HFBR was shut down by the Department of Energy (DOE) and an extensive review of the HFBR was initiated. In an effort to address this issue BNL developed a model designed to predict the heat removal limit during flow reversal that was found to be in good agreement with the test results. Currently a thermal-hydraulic test program is being developed to provide a more realistic and defensible estimate of the flow reversal heat removal limit so that the reactor power level can be increased.« less

TRAC-P1: an advanced best estimate computer program for PWR LOCA analysis. I. Methods, models, user information, and programming details

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-05-01

The Transient Reactor Analysis Code (TRAC) is being developed at the Los Alamos Scientific Laboratory (LASL) to provide an advanced ''best estimate'' predictive capability for the analysis of postulated accidents in light water reactors (LWRs). TRAC-Pl provides this analysis capability for pressurized water reactors (PWRs) and for a wide variety of thermal-hydraulic experimental facilities. It features a three-dimensional treatment of the pressure vessel and associated internals; two-phase nonequilibrium hydrodynamics models; flow-regime-dependent constitutive equation treatment; reflood tracking capability for both bottom flood and falling film quench fronts; and consistent treatment of entire accident sequences including the generation of consistent initial conditions.more » The TRAC-Pl User's Manual is composed of two separate volumes. Volume I gives a description of the thermal-hydraulic models and numerical solution methods used in the code. Detailed programming and user information is also provided. Volume II presents the results of the developmental verification calculations.« less

Aging, Loss-of-Coolant Accident (LOCA), and high potential testing of damaged cables

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, R.A.; Jacobus, M.J.

1994-04-01

Experiments were conducted to assess the effects of high potential testing of cables and to assess the survivability of aged and damaged cables under Loss-of-Coolant Accident (LOCA) conditions. High potential testing at 240 Vdc/mil on undamaged cables suggested that no damage was incurred on the selected virgin cables. During aging and LOCA testing, Okonite ethylene propylene rubber (EPR) cables with a bonded jacket experienced unexpected failures. The failures appear to be primarily related to the level of thermal aging and the presence of a bonded jacket that ages more rapidly than the insulation. For Brand Rex crosslinked polyolefin (XLPO) cables,more » the results suggest that 7 mils of insulation remaining should give the cables a high probability of surviving accident exposure following aging. The voltage necessary to detect when 7 mils of insulation remain on unaged Brand Rex cables is approximately 35 kVdc. This voltage level would almost certainly be unacceptable to a utility for use as a damage assessment tool. However, additional tests indicated that a 35 kvdc voltage application would not damage virgin Brand Rex cables when tested in water. Although two damaged Rockbestos silicone rubber cables also failed during the accident test, no correlation between failures and level of damage was apparent.« less

Comparisons of Wilks’ and Monte Carlo Methods in Response to the 10CFR50.46(c) Proposed Rulemaking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Hongbin; Szilard, Ronaldo; Zou, Ling

The Nuclear Regulatory Commission (NRC) is proposing a new rulemaking on emergency core system/loss-of-coolant accident (LOCA) performance analysis. In the proposed rulemaking, designated as 10CFR50.46(c), the US NRC put forward an equivalent cladding oxidation criterion as a function of cladding pre-transient hydrogen content. The proposed rulemaking imposes more restrictive and burnup-dependent cladding embrittlement criteria; consequently nearly all the fuel rods in a reactor core need to be analyzed under LOCA conditions to demonstrate compliance to the safety limits. New analysis methods are required to provide a thorough characterization of the reactor core in order to identify the locations of themore » limiting rods as well as to quantify the safety margins under LOCA conditions. With the new analysis method presented in this work, the limiting transient case and the limiting rods can be easily identified to quantify the safety margins in response to the proposed new rulemaking. In this work, the best-estimate plus uncertainty (BEPU) analysis capability for large break LOCA with the new cladding embrittlement criteria using the RELAP5-3D code is established and demonstrated with a reduced set of uncertainty parameters. Both the direct Monte Carlo method and the Wilks’ nonparametric statistical method can be used to perform uncertainty quantification. Wilks’ method has become the de-facto industry standard to perform uncertainty quantification in BEPU LOCA analyses. Despite its widespread adoption by the industry, the use of small sample sizes to infer statement of compliance to the existing 10CFR50.46 rule, has been a major cause of unrealized operational margin in today’s BEPU methods. Moreover the debate on the proper interpretation of the Wilks’ theorem in the context of safety analyses is not fully resolved yet, even more than two decades after its introduction in the frame of safety analyses in the nuclear industry. This represents both a regulatory and application risk in rolling out new methods. With the 10CFR50.46(c) proposed rulemaking, the deficiencies of the Wilks’ approach are further exacerbated. The direct Monte Carlo approach offers a robust alternative to perform uncertainty quantification within the context of BEPU analyses. In this work, the Monte Carlo method is compared with the Wilks’ method in response to the NRC 10CFR50.46(c) proposed rulemaking.« less

A Study of the Jettisoning of JP-4 Fuel in the Atmosphere

DTIC Science & Technology

1975-11-01

t e r m i n e d by m e a s u r i n g the s tagna t ion p r e s s u r e with a pitot probe , shown in Fig. 21, with the s p h e r i c a l t...ip. The rod loca ted to the r igh t of the pitot probe was loca ted in the s a m e photographic plane as the suspended J P - 4 drop- le t...of Atomiza t ion in C a r b u r e t o r s . " NACA TM 518, 1929. 13. Lapple , C. E . , Henry , J . P . , J r . , and Blake, D. E. " A t o

Posttest analysis of international standard problem 10 using RELAP4/MOD7. [PWR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hsu, M.; Davis, C.B.; Peterson, A.C. Jr.

RELAP4/MOD7, a best estimate computer code for the calculation of thermal and hydraulic phenomena in a nuclear reactor or related system, is the latest version in the RELAP4 code development series. This paper evaluates the capability of RELAP4/MOD7 to calculate refill/reflood phenomena. This evaluation uses the data of International Standard Problem 10, which is based on West Germany's KWU PKL refill/reflood experiment K9A. The PKL test facility represents a typical West German four-loop, 1300 MW pressurized water reactor (PWR) in reduced scale while maintaining prototypical volume-to-power ratio. The PKL facility was designed to specifically simulate the refill/reflood phase of amore » hypothetical loss-of-coolant accident (LOCA).« less

Numerical study of air ingress transition to natural circulation in a high temperature helium loop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Franken, Daniel; Gould, Daniel; Jain, Prashant K.

Here, the generation-IV high temperature gas cooled reactors (HTGRs) are designed with many passive safety features, one of which is the ability to passively remove heat under a loss of coolant accident (LOCA). However, several common reactor designs do not prevent against a large break in the coolant system and may therefore experience a depressurized LOCA. This would lead to air entering into the reactor system via several potential modes of ingress: diffusion, gravity currents, and natural circulation. At the onset of a LOCA, the initial rate of air ingress is expected to be very slow because it is governedmore » by molecular diffusion. However, after several hours, natural circulation would commence, thus, bringing the air into the reactor system at a much higher rate. As a consequence, air ingress would cause the high temperature graphite matrix to oxidize, leading to its thermal degradation and decreased passive heat (decay) removal capability. Therefore, it is essential to understand the transition of air ingress from molecular diffusion to natural circulation in an HTGR system. This paper presents results from a computational fluid dynamics (CFD) model to study the air ingress transition behavior. These results are validated against an h-shaped high temperature helium loop experiment. Details are provided to quantitatively predict the transition time from molecular diffusion to natural circulation.« less

Numerical study of air ingress transition to natural circulation in a high temperature helium loop

DOE PAGES

Franken, Daniel; Gould, Daniel; Jain, Prashant K.; ...

2017-09-21

Here, the generation-IV high temperature gas cooled reactors (HTGRs) are designed with many passive safety features, one of which is the ability to passively remove heat under a loss of coolant accident (LOCA). However, several common reactor designs do not prevent against a large break in the coolant system and may therefore experience a depressurized LOCA. This would lead to air entering into the reactor system via several potential modes of ingress: diffusion, gravity currents, and natural circulation. At the onset of a LOCA, the initial rate of air ingress is expected to be very slow because it is governedmore » by molecular diffusion. However, after several hours, natural circulation would commence, thus, bringing the air into the reactor system at a much higher rate. As a consequence, air ingress would cause the high temperature graphite matrix to oxidize, leading to its thermal degradation and decreased passive heat (decay) removal capability. Therefore, it is essential to understand the transition of air ingress from molecular diffusion to natural circulation in an HTGR system. This paper presents results from a computational fluid dynamics (CFD) model to study the air ingress transition behavior. These results are validated against an h-shaped high temperature helium loop experiment. Details are provided to quantitatively predict the transition time from molecular diffusion to natural circulation.« less

New reactor cavity cooling system having passive safety features using novel shape for HTGRs and VHTRs

DOE PAGES

Takamatsu, Kuniyoshi; Hu, Rui

2014-11-27

A new, highly efficient reactor cavity cooling system (RCCS) with passive safety features without a requirement for electricity and mechanical drive is proposed for high temperature gas cooled reactors (HTGRs) and very high temperature reactors (VHTRs). The RCCS design consists of continuous closed regions; one is an ex-reactor pressure vessel (RPV) region and another is a cooling region having heat transfer area to ambient air assumed at 40 (°C). The RCCS uses a novel shape to efficiently remove the heat released from the RPV with radiation and natural convection. Employing the air as the working fluid and the ambient airmore » as the ultimate heat sink, the new RCCS design strongly reduces the possibility of losing the heat sink for decay heat removal. Therefore, HTGRs and VHTRs adopting the new RCCS design can avoid core melting due to overheating the fuels. The simulation results from a commercial CFD code, STAR-CCM+, show that the temperature distribution of the RCCS is within the temperature limits of the structures, such as the maximum operating temperature of the RPV, 713.15 (K) = 440 (°C), and the heat released from the RPV could be removed safely, even during a loss of coolant accident (LOCA). Finally, when the RCCS can remove 600 (kW) of the rated nominal state even during LOCA, the safety review for building the HTTR could confirm that the temperature distribution of the HTTR is within the temperature limits of the structures to secure structures and fuels after the shutdown because the large heat capacity of the graphite core can absorb heat from the fuel in a short period. Therefore, the capacity of the new RCCS design would be sufficient for decay heat removal.« less

Severe Accident Test Station Design Document

DOE Office of Scientific and Technical Information (OSTI.GOV)

Snead, Mary A.; Yan, Yong; Howell, Michael

The purpose of the ORNL severe accident test station (SATS) is to provide a platform for evaluation of advanced fuels under projected beyond design basis accident (BDBA) conditions. The SATS delivers the capability to map the behavior of advanced fuels concepts under accident scenarios across various temperature and pressure profiles, steam and steam-hydrogen gas mixtures, and thermal shock. The overall facility will include parallel capabilities for examination of fuels and irradiated materials (in-cell) and non-irradiated materials (out-of-cell) at BDBA conditions as well as design basis accident (DBA) or loss of coolant accident (LOCA) conditions. Also, a supporting analytical infrastructure tomore » provide the data-needs for the fuel-modeling components of the Fuel Cycle Research and Development (FCRD) program will be put in place in a parallel manner. This design report contains the information for the first, second and third phases of design and construction of the SATS. The first phase consisted of the design and construction of an out-of-cell BDBA module intended for examination of non-irradiated materials. The second phase of this work was to construct the BDBA in-cell module to test irradiated fuels and materials as well as the module for DBA (i.e. LOCA) testing out-of-cell, The third phase was to build the in-cell DBA module. The details of the design constraints and requirements for the in-cell facility have been closely captured during the deployment of the out-of-cell SATS modules to ensure effective future implementation of the in-cell modules.« less

The R&D PERFROI Project on Thermal Mechanical and Thermal Hydraulics Behaviors of a Fuel Rod Assembly during a Loss of Coolant Accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Repetto, G.; Dominguez, C.; Durville, B.

The safety principle in case of a LOCA is to preserve the short and long term coolability of the core. The associated safety requirements are to ensure the resistance of the fuel rods upon quench and post-quench loads and to maintain a coolable geometry in the core. An R&D program has been launched by IRSN with the support of EDF, to perform both experimental and modeling activities in the frame of the LOCA transient, on technical issues such as: - flow blockage within a fuel rods bundle and its potential impact on coolability, - fuel fragment relocation in the balloonedmore » areas: its potential impact on cladding PCT (Peak Cladding Temperature) and on the maximum oxidation rate, - potential loss of cladding integrity upon quench and post-quench loads. The PERFROI project (2014-2019) focusing on the first above issue, is structured in two axes: 1. axis 1: thermal mechanical behavior of deformation and rupture of cladding taking into account the contact between fuel rods; specific research at LaMCoS laboratory focus on the hydrogen behavior in cladding alloys and its impact on the mechanical behavior of the rod; and, 2. axis 2: thermal hydraulics study of a partially blocked region of the core (ballooned area taking into account the fuel relocation with local over power), during cooling phase by water injection; More detailed activities foreseen in collaboration with LEMTA laboratory will focus on the characterization of two phase flows with heat transfer in deformed structures.« less

Cladding burst behavior of Fe-based alloys under LOCA

DOE PAGES

Terrani, Kurt A.; Dryepondt, Sebastien N.; Pint, Bruce A.; ...

2015-12-17

Burst behavior of austenitic and ferritic Fe-based alloy tubes has been examined under a simulated large break loss of coolant accident. Specifically, type 304 stainless steel (304SS) and oxidation resistant FeCrAl tubes were studied alongside Zircaloy-2 and Zircaloy-4 that are considered reference fuel cladding materials. Following the burst test, characterization of the cladding materials was carried out to gain insights regarding the integral burst behavior. Given the widespread availability of a comprehensive set of thermo-mechanical data at elevated temperatures for 304SS, a modeling framework was implemented to simulate the various processes that affect burst behavior in this Fe-based alloy. Themore » most important conclusion is that cladding ballooning due to creep is negligible for Fe-based alloys. Thus, unlike Zr-based alloys, cladding cross-sectional area remains largely unchanged up to the point of burst. Furthermore, for a given rod internal pressure, the temperature onset of burst in Fe-based alloys appears to be simply a function of the alloy's ultimate tensile strength, particularly at high rod internal pressures.« less

Mechanism-based modeling of solute strengthening: application to thermal creep in Zr alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tome, Carlos; Wen, Wei; Capolungo, Laurent

2017-08-01

This report focuses on the development of a physics-based thermal creep model aiming to predict the behavior of Zr alloy under reactor accident condition. The current models used for this kind of simulations are mostly empirical in nature, based generally on fits to the experimental steady-state creep rates under different temperature and stress conditions, which has the following limitations. First, reactor accident conditions, such as RIA and LOCA, usually take place in short times and involve only the primary, not the steady-state creep behavior stage. Moreover, the empirical models cannot cover the conditions from normal operation to accident environments. Formore » example, Kombaiah and Murty [1,2] recently reported a transition between the low (n~4) and high (n~9) power law creep regimes in Zr alloys depending on the applied stress. Capturing such a behavior requires an accurate description of the mechanisms involved in the process. Therefore, a mechanism-based model that accounts for the evolution with time of microstructure is more appropriate and reliable for this kind of simulation.« less

Transient analysis of ”2 inch Direct Vessel Injection line break” in SPES-2 facility by using TRACE code

NASA Astrophysics Data System (ADS)

D'Amico, S.; Lombardo, C.; Moscato, I.; Polidori, M.; Vella, G.

2015-11-01

In the past few decades a lot of theoretical and experimental researches have been done to understand the physical phenomena characterizing nuclear accidents. In particular, after the Three Miles Island accident, several reactors have been designed to handle successfully LOCA events. This paper presents a comparison between experimental and numerical results obtained for the “2 inch Direct Vessel Injection line break” in SPES-2. This facility is an integral test facility built in Piacenza at the SIET laboratories and simulating the primary circuit, the relevant parts of the secondary circuits and the passive safety systems typical of the AP600 nuclear power plant. The numerical analysis here presented was performed by using TRACE and CATHARE thermal-hydraulic codes with the purpose of evaluating their prediction capability. The main results show that the TRACE model well predicts the overall behaviour of the plant during the transient, in particular it is able to simulate the principal thermal-hydraulic phenomena related to all passive safety systems. The performance of the presented CATHARE noding has suggested some possible improvements of the model.

A guide to aviation education resources

DOT National Transportation Integrated Search

1993-01-01

The National Coalition for Aviation Education represents industry and labor, united to promote : aviation education activities and resources; increase public understanding of the importance of aviation; and support educational initiatives at the loca...

Partnership strategies for safety roadside rest areas.

DOT National Transportation Integrated Search

2009-01-01

This project studied the many factors influencing the potential for public private partnerships for Safety : Roadside Rest Areas. It found that Federal and California State laws and regulations represent important : barriers to certain types and loca...

A framework for collaboration in public transit systems

DOT National Transportation Integrated Search

1997-05-01

The 494 transportation corridor stretches eight miles and connects residential suburbs with major commercial areas, including the Mall of America and the Minneapolis-St. Paul International Airport. The corridor includes l-494 as well as parallel loca...

Passive containment cooling system

DOEpatents

Billig, P.F.; Cooke, F.E.; Fitch, J.R.

1994-01-25

A passive containment cooling system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel and is vented to the drywell. An isolation pool is disposed above the GDCS pool and includes an isolation condenser therein. The condenser has an inlet line disposed in flow communication with the drywell for receiving the non-condensable gas along with any steam released therein following a loss-of-coolant accident (LOCA). The condenser also has an outlet line disposed in flow communication with the drywell for returning to the drywell both liquid condensate produced upon cooling of the steam and the non-condensable gas for reducing pressure within the containment vessel following the LOCA. 1 figure.

Passive containment cooling system

DOEpatents

Billig, Paul F.; Cooke, Franklin E.; Fitch, James R.

1994-01-01

A passive containment cooling system includes a containment vessel surrounding a reactor pressure vessel and defining a drywell therein containing a non-condensable gas. An enclosed wetwell pool is disposed inside the containment vessel, and a gravity driven cooling system (GDCS) pool is disposed above the wetwell pool in the containment vessel and is vented to the drywell. An isolation pool is disposed above the GDCS pool and includes an isolation condenser therein. The condenser has an inlet line disposed in flow communication with the drywell for receiving the non-condensable gas along with any steam released therein following a loss-of-coolant accident (LOCA). The condenser also has an outlet line disposed in flow communication with the drywell for returning to the drywell both liquid condensate produced upon cooling of the steam and the non-condensable gas for reducing pressure within the containment vessel following the LOCA.

Influence of chemical composition of zirconium alloy E110 on embrittlement under LOCA conditions - Part 1: Oxidation kinetics and macrocharacteristics of structure and fracture

NASA Astrophysics Data System (ADS)

Nikulin, S. A.; Rozhnov, A. B.; Belov, V. A.; Li, E. V.; Glazkina, V. S.

2011-11-01

Exploratory investigations of the influence of alloying and impurity content in the E110 alloy cladding tubes on the behavior under conditions of Loss of Coolant Accidents (LOCA) has been performed. Three alloys of E110 type have been tested: E110 alloy of nominal composition Zr-1%Nb (E110), E110 alloy of modified composition Zr-1%Nb-0.12%Fe-0.13%O (E110M), E110 alloy of nominal composition Zr-1%Nb with reduced impurity content (E110G). Alloys E110 and E110M were manufactured on the electrolytic basis and alloy E110G was manufactured on the basis of zirconium sponge. The high temperature oxidation tests in steam ( T = 1100 °C, 18% of equivalent cladding reacted (ECR)) have been conducted, kinetics of oxidation was investigated. Quantitative research of structure and fracture macrocharacteristics was performed by means of optical and electron microscopy. The results received were compared with the residual ductility of specimens. The results of the investigation showed the existence of "breakaway oxidation" kinetics and white spalling oxide in E110 and E110M alloys while the specimen oxidation kinetics in E110G alloy was characterized by a parabolic law and specimens had a dense black oxide. Oxygen and iron alloying in the E110 alloy positively changed the macrocharacteristics of structure and fracture. However, in general, it did not improve the resistance to embrittlement in LOCA conditions apparently because of a strong impurity influence caused by electrolytic process of zirconium production.

Analysis of LOCA Scenarios in the NIST Research Reactor Before and After Fuel Conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baek, J. S.; Cheng, L. Y.; Diamond, D.

An analysis has been done of hypothetical loss-of-coolant-accidents (LOCAs) in the research reactor (NBSR) at the National Institute of Standards and Technology (NIST). The purpose of the analysis is to determine if the peak clad temperature remains below the Safety Limit, which is the blister temperature for the fuel. The configuration of the NBSR considered in the analysis is that projected for the future when changes will be made so that shutdown pumps do not operate when a LOCA signal is detected. The analysis was done for the present core with high-enriched uranium (HEU) fuel and with the proposed low-enrichedmore » uranium (LEU) fuel that would be used when the NBSR is converted from one to the other. The analysis consists of two parts. The first examines how the water would drain from the primary system following a break and the possibility for the loss of coolant from within the fuel element flow channels. This work is performed using the TRACE system thermal-hydraulic code. The second looks at the fuel clad temperature as a function of time given that the water may have drained from many of the flow channels and the water in the vessel is in a quasi-equilibrium state. The temperature behavior is investigated using the three-dimensional heat conduction code HEATING7.3. The results in all scenarios considered for both HEU and LEU fuel show that the peak clad temperature remains below the blister temperature.« less

Sensitivity analysis of FeCrAl cladding and U3Si2 fuel under accident conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamble, Kyle Allan Lawrence; Hales, Jason Dean

2016-08-01

The purpose of this milestone report is to highlight the results of sensitivity analyses performed on two accident tol- erant fuel concepts: U3Si2 fuel and FeCrAl cladding. The BISON fuel performance code under development at Idaho National Laboratory was coupled to Sandia National Laboratories’ DAKOTA software to perform the sensitivity analyses. Both Loss of Coolant (LOCA) and Station blackout (SBO) scenarios were analyzed using main effects studies. The results indicate that for FeCrAl cladding the input parameters with greatest influence on the output metrics of interest (fuel centerline temperature and cladding hoop strain) during the LOCA were the isotropic swellingmore » and fuel enrichment. For U3Si2 the important inputs were found to be the intergranular diffusion coefficient, specific heat, and fuel thermal conductivity. For the SBO scenario, Young’s modulus was found to be influential in FeCrAl in addition to the isotropic swelling and fuel enrichment. Contrarily to the LOCA case, the specific heat of U3Si2 was found to have no effect during the SBO. The intergranular diffusion coefficient and fuel thermal conductivity were still found to be of importance. The results of the sensitivity analyses have identified areas where further research is required including fission gas behavior in U3Si2 and irradiation swelling in FeCrAl. Moreover, the results highlight the need to perform the sensitivity analyses on full length fuel rods for SBO scenarios.« less

Traffic control at stop sign approaches.

DOT National Transportation Integrated Search

2003-04-01

The objectives of this report were to: a) determine the number of crashes in Kentucky involving a driver disregarding a stop sign and the locations where these occur, b) determine the characteristics of these crashes, c) investigate loca tions with a...

Innovative tools and techniques in identifying highway safety improvement projects : project summary.

DOT National Transportation Integrated Search

2017-01-01

Researchers completed the following activities: - Reviewed the literature, state HSIP processes and practices, and HSIP tools used by various agencies. - Evaluated the applicability of safety assessment methods and tools used by other states and loca...

VHF-FM Emergency Position Indicating Radio Beacon

DOT National Transportation Integrated Search

1978-10-01

This report describes the development and testing of an Emergency Position Indicating Radio Beacon (EPIRB) which operates on Channels 15 and 16 of the Maritime Mobile VHF Band. It provides functions necessary to ensure that distress alerting and loca...

Hydrochemical simulation of a mountain basin under hydrological variability

NASA Astrophysics Data System (ADS)

Montserrat, S.; Trewhela, T. A.; Navarro, L.; Navarrete, A.; Lagos Zuniga, M. A.; Garcia, A.; Caraballo, M.; Niño, Y.; McPhee, J. P.

2016-12-01

Water quality and the comprehension of hydrochemical phenomena in natural basins should be of complete relevance under hydrological uncertainties. The importance of identifying the main variables that are controlling a natural system and finding a way to predict their behavior under variable scenarios is mandatory to preserve these natural basins. This work presents an interdisciplinary model for the Yerba Loca watershed, a natural reserve basin in the Chilean central Andes. Based on different data sets, provided by public and private campaigns, a natural hydrochemical regime was identified. Yerba Loca is a natural reserve, characterized by the presence of several glaciers and wide sediment deposits crossed by a small low-slope creek in the upper part of the basin that leads to a high-slope narrow channel with less sediment depositions. Most relevant is the geological context around the glaciers, considering that most of them cover hydrothermal zones rich in both sulfides and sulfates, a situation commonly found in the Andes due to volcanic activity. Low pH (around 3), calcium-sulfate water with high concentrations of Iron, Copper and Zinc are found in the upper part of the basin in summer. These values can be attributed to the glaciers melting down and draining of the mentioned country rocks, which provide most of the creek flow in the upper basin. The latter clearly contrasts with the creek outlet, located 18 km downstream, showing near to neutral pH values and lower concentrations of the elements already mentioned. The scope of the present research is to account for the sources of the different hydrological inlets (e.g., rainfall, snow and/or glacier melting) that, depending on their location, may interact with a variety of reactive minerals and generate acid rock drainage (ARD). The inlet water is modeled along the creek using the softwares HEC-RAS and PHREEQC coupled, in order to characterize the water quality and to detect preferred sedimentation sections retaining precipitated minerals, mostly Iron and Aluminium hydroxysulfates, due to low velocity flow in those areas. Validation of the results is done using several data sets that show cycles along seasons under variable outflow and chemical conditions in the outlet of the basin, responding to the same inflow and initial chemical data used for simulation.

ACHILLES: Heat Transfer in PWR Core During LOCA Reflood Phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

2013-11-01

1. NAME AND TITLE OF DATA LIBRARY ACHILLES -Heat Transfer in PWR Core During LOCA Reflood Phase. 2. NAME AND TITLE OF DATA RETRIEVAL PROGRAMS N/A 3. CONTRIBUTOR AEA Technology, Winfrith Technology Centre, Dorchester DT2 8DH United Kingdom through the OECD Nuclear Energy Agency Data Bank, Issy-les-Moulineaux, France. 4. DESCRIPTION OF TEST FACILITY The most important features of the Achilles rig were the shroud vessel, which contained the test section, and the downcomer. These may be thought of as representing the core barrel and the annular downcomer in the reactor pressure vessel. The test section comprises a cluster of 69more » rods in a square array within a circular shroud vessel. The rod diameter and pitch (9.5 mm and 12.6 mm) were typical of PWR dimensions. The internal diameter of the shroud vessel was 128 mm. Each rod was electrically heated over a length of 3.66 m, which is typical of the nuclear heated length in a PWR fuel rod, and each contained 6 internal thermocouples. These were arranged in one of 8 groupings which concentrated the thermocouples in different axial zones. The spacer grids were at prototypic PWR locations. Each grid had two thermocouples attached to its trailing edge at radial locations. The axial power profile along the rods was an 11 step approximation to a "chopped cosine". The shroud vessel had 5 heating zones whose power could be independently controlled. 5. DESCRIPTION OF TESTS The Achilles experiments investigated the heat transfer in the core of a Pressurized Water Reactor during the re-flood phase of a postulated large break loss of coolant accident. The results provided data to validate codes and to improve modeling. Different types of experiments were carried out which included single phase cooling, re-flood under low flow conditions, level swell and re-flood under high flow conditions. Three series of experiments were performed. The first and the third used the same test section but the second used another test section, similar in all respects except that it contained a partial blockage formed by attaching sleeves (or "balloons") to some of the rods. 6. SOURCE AND SCOPE OF DATA Phenomena Tested - Heat transfer in the core of a PWR during a re-flood phase of postulated large break LOCA. Test Designation - Achilles Rig. The programme includes the following types of experiments: - on an unballooned cluster: -- single phase air flow -- low pressure level swell -- low flooding rate re-flood -- high flooding rate re-flood - on a ballooned cluster containing 80% blockage formed by 16 balloon sleeves -- single phase air flow -- low flooding rate re-flood 7. DISCUSSION OF THE DATA RETRIEVAL PROGRAM N/A 8. DATA FORMAT AND COMPUTER Many Computers (M00019MNYCP00). 9. TYPICAL RUNNING TIME N/A 11. CONTENTS OF LIBRARY The ACHILLES package contains test data and associated data processing software as well as the documentation listed above. 12. DATE OF ABSTRACT November 2013. KEYWORDS: DATABASES, BENCHMARKS, HEAT TRANSFER, LOSS-OF-COLLANT ACCIDENT, PWR REACTORS, REFLOODING« less

Preliminary analysis of loss-of-coolant accident in Fukushima nuclear accident

DOE Office of Scientific and Technical Information (OSTI.GOV)

Su'ud, Zaki; Anshari, Rio

Loss-of-Coolant Accident (LOCA) in Boiling Water Reactor (BWR) especially on Fukushima Nuclear Accident will be discussed in this paper. The Tohoku earthquake triggered the shutdown of nuclear power reactors at Fukushima Nuclear Power station. Though shutdown process has been completely performed, cooling process, at much smaller level than in normal operation, is needed to remove decay heat from the reactor core until the reactor reach cold-shutdown condition. If LOCA happen at this condition, it will cause the increase of reactor fuel and other core temperatures and can lead to reactor core meltdown and exposure of radioactive material to the environmentmore » such as in the Fukushima Dai Ichi nuclear accident case. In this study numerical simulation has been performed to calculate pressure composition, water level and temperature distribution on reactor during this accident. There are two coolant regulating system that operational on reactor unit 1 at this accident, Isolation Condensers (IC) system and Safety Relief Valves (SRV) system. Average mass flow of steam to the IC system in this event is 10 kg/s and could keep reactor core from uncovered about 3,2 hours and fully uncovered in 4,7 hours later. There are two coolant regulating system at operational on reactor unit 2, Reactor Core Isolation Condenser (RCIC) System and Safety Relief Valves (SRV). Average mass flow of coolant that correspond this event is 20 kg/s and could keep reactor core from uncovered about 73 hours and fully uncovered in 75 hours later. There are three coolant regulating system at operational on reactor unit 3, Reactor Core Isolation Condenser (RCIC) system, High Pressure Coolant Injection (HPCI) system and Safety Relief Valves (SRV). Average mass flow of water that correspond this event is 15 kg/s and could keep reactor core from uncovered about 37 hours and fully uncovered in 40 hours later.« less

Probabilistic risk assessment for a loss of coolant accident in McMaster Nuclear Reactor and application of reliability physics model for modeling human reliability

NASA Astrophysics Data System (ADS)

Ha, Taesung

A probabilistic risk assessment (PRA) was conducted for a loss of coolant accident, (LOCA) in the McMaster Nuclear Reactor (MNR). A level 1 PRA was completed including event sequence modeling, system modeling, and quantification. To support the quantification of the accident sequence identified, data analysis using the Bayesian method and human reliability analysis (HRA) using the accident sequence evaluation procedure (ASEP) approach were performed. Since human performance in research reactors is significantly different from that in power reactors, a time-oriented HRA model (reliability physics model) was applied for the human error probability (HEP) estimation of the core relocation. This model is based on two competing random variables: phenomenological time and performance time. The response surface and direct Monte Carlo simulation with Latin Hypercube sampling were applied for estimating the phenomenological time, whereas the performance time was obtained from interviews with operators. An appropriate probability distribution for the phenomenological time was assigned by statistical goodness-of-fit tests. The human error probability (HEP) for the core relocation was estimated from these two competing quantities: phenomenological time and operators' performance time. The sensitivity of each probability distribution in human reliability estimation was investigated. In order to quantify the uncertainty in the predicted HEPs, a Bayesian approach was selected due to its capability of incorporating uncertainties in model itself and the parameters in that model. The HEP from the current time-oriented model was compared with that from the ASEP approach. Both results were used to evaluate the sensitivity of alternative huinan reliability modeling for the manual core relocation in the LOCA risk model. This exercise demonstrated the applicability of a reliability physics model supplemented with a. Bayesian approach for modeling human reliability and its potential usefulness of quantifying model uncertainty as sensitivity analysis in the PRA model.

Preliminary analysis of loss-of-coolant accident in Fukushima nuclear accident

NASA Astrophysics Data System (ADS)

Su'ud, Zaki; Anshari, Rio

2012-06-01

Loss-of-Coolant Accident (LOCA) in Boiling Water Reactor (BWR) especially on Fukushima Nuclear Accident will be discussed in this paper. The Tohoku earthquake triggered the shutdown of nuclear power reactors at Fukushima Nuclear Power station. Though shutdown process has been completely performed, cooling process, at much smaller level than in normal operation, is needed to remove decay heat from the reactor core until the reactor reach cold-shutdown condition. If LOCA happen at this condition, it will cause the increase of reactor fuel and other core temperatures and can lead to reactor core meltdown and exposure of radioactive material to the environment such as in the Fukushima Dai Ichi nuclear accident case. In this study numerical simulation has been performed to calculate pressure composition, water level and temperature distribution on reactor during this accident. There are two coolant regulating system that operational on reactor unit 1 at this accident, Isolation Condensers (IC) system and Safety Relief Valves (SRV) system. Average mass flow of steam to the IC system in this event is 10 kg/s and could keep reactor core from uncovered about 3,2 hours and fully uncovered in 4,7 hours later. There are two coolant regulating system at operational on reactor unit 2, Reactor Core Isolation Condenser (RCIC) System and Safety Relief Valves (SRV). Average mass flow of coolant that correspond this event is 20 kg/s and could keep reactor core from uncovered about 73 hours and fully uncovered in 75 hours later. There are three coolant regulating system at operational on reactor unit 3, Reactor Core Isolation Condenser (RCIC) system, High Pressure Coolant Injection (HPCI) system and Safety Relief Valves (SRV). Average mass flow of water that correspond this event is 15 kg/s and could keep reactor core from uncovered about 37 hours and fully uncovered in 40 hours later.

Vehicle kinematics in turns and the role of cornering lamps in driver vision.

DOT National Transportation Integrated Search

2010-11-01

"SAE Recommended Practice J852 and ECE Regulations 119 and 48 for cornering lamps : were compared. Photometric points described in each specification were then compared : to naturalistic low-speed turn trajectories produced by 87 drivers. Future loca...

Church ladies, good girls, and locas: stigma and the intersection of gender, ethnicity, mental illness, and sexuality in relation to HIV risk.

PubMed

Collins, Pamela Y; von Unger, Hella; Armbrister, Adria

2008-08-01

Inner city women with severe mental illness may carry multiple stigmatized statuses. In some contexts these include having a mental illness, being a member of an ethnic minority group, being an immigrant, being poor, and being a woman who does not live up to gendered expectations. These potentially stigmatizing identities influence both the way women's sexuality is viewed and their risk for HIV infection. This qualitative study applies the concept of intersectionality to facilitate understanding of how these multiple identities intersect to influence women's sexuality and HIV risk. We report the firsthand accounts of 24 Latina women living with severe mental illness in New York City. In examining the interlocking domains of these women's sexual lives, we find that the women seek identities that define them in opposition to the stigmatizing label of "loca" (Spanish for crazy) and bestow respect and dignity. These identities have unfolded through the additional themes of "good girls" and "church ladies". Therefore, in spite of their association with the "loca", the women also identify with faith and religion ("church ladies") and uphold more traditional gender norms ("good girls") that are often undermined by the realities of life with a severe mental illness and the stigma attached to it. However, the participants fall short of their gender ideals and engage in sexual relationships that they experience as disempowering and unsatisfying. The effects of their multiple identities as poor Latina women living with severe mental illness in an urban ethnic minority community are not always additive, but the interlocking effects can facilitate increased HIV risks. Interventions should acknowledge women's multiple layers of vulnerability, both individual and structural, and stress women's empowerment in and beyond the sexual realm.

Effect of excess dietary salt on calcium metabolism and bone mineral in a spaceflight rat model

NASA Technical Reports Server (NTRS)

Navidi, Meena; Wolinsky, Ira; Fung, Paul; Arnaud, Sara B.

1995-01-01

High levels of salt promote urinary calcium (UCa) loss and have the potential to cause bone mineral deficits if intestinal Ca absorption does not compensate for these losses. To determine the effect of excess dietary salt on the osteopenia that follows skeletal unloading, we used a spaceflight model that unloads the hindlimbs of 200-g rats by tail suspension (S). Rats were studied for 2 wk on diets containing high salt (4 and 8%) and normal calcium (0.45%) and for 4 wk on diets containing 8% salt (HiNa) and 0.2% Ca (LoCa). Final body weights were 9-11% lower in S than in control rats (C) in both experiments, reflecting lower growth rates in S than in C during pair feeding. UCa represented 12% of dietary Ca on HiNA diets and was twofold higher in S than in C transiently during unloading. Net intestinal Ca absorption was consistently 11-18% lower in S than in C. Serum 1,25-dihydroxyvitamin D was unaffected by either LoCa or HiNa diets in S but was increased by LoCa and HiNa diets in C. Despite depressed intestinal Ca absoption in S and a sluggish response of the Ca endocrine system to HiNa diets, UCa loss did not appear to affect the osteopenia induced by unloading. Although any deficit in bone mineral content from HiNa diets may have been too small to detect or the duration of the study too short to manifest, there were clear differences in Ca metabolism from control levels in the response of the spaceflight model to HiNa diets, indicated by depression of intestinal Ca absorption and its regulatory hormone.

Oxidation of 304 stainless steel in high-temperature steam

NASA Astrophysics Data System (ADS)

Ishida, Toshihisa; Harayama, Yasuo; Yaguchi, Sinnosuke

1986-08-01

An experiment on oxidation of 304 stainless steel was performed in steam between 900°C and 1350°C, using the spare cladding of the reactor of the nuclear-powered ship Mutsu. The temperature range was appropriate for a postulated loss of coolant accident (LOCA) analysis of a LWR. The oxidation kinetics were found to obey the parabolic law during the first period of 8 min. After the first period, the parabolic reaction rate constant decreased in the case of heating temperatures between 1100°C and 1250°C. At 1250°C, especially, a marked decrease was observed in the oxide scale-forming kinetics when the surface treated initially by mechanical polishing and given a residual stress. This enhanced oxidation resistance was attributed to the presence of a chromium-enriched layer which was detected by use of an X-ray microanalyzer. The oxidation kinetics equation obtained for the first 8 min is applicable to the model calculation of a hypothetical LOCA in a LWR, employing 304 stainless steel cladding.

Hot Cell Installation and Demonstration of the Severe Accident Test Station

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linton, Kory D.; Burns, Zachary M.; Terrani, Kurt A.

A Severe Accident Test Station (SATS) capable of examining the oxidation kinetics and accident response of irradiated fuel and cladding materials for design basis accident (DBA) and beyond design basis accident (BDBA) scenarios has been successfully installed and demonstrated in the Irradiated Fuels Examination Laboratory (IFEL), a hot cell facility at Oak Ridge National Laboratory. The two test station modules provide various temperature profiles, steam, and the thermal shock conditions necessary for integral loss of coolant accident (LOCA) testing, defueled oxidation quench testing and high temperature BDBA testing. The installation of the SATS system restores the domestic capability to examinemore » postulated and extended LOCA conditions on spent fuel and cladding and provides a platform for evaluation of advanced fuel and accident tolerant fuel (ATF) cladding concepts. This document reports on the successful in-cell demonstration testing of unirradiated Zircaloy-4. It also contains descriptions of the integral test facility capabilities, installation activities, and out-of-cell benchmark testing to calibrate and optimize the system.« less

Developpement d'une methode de Monte Carlo dependante du temps et application au reacteur de type CANDU-6

NASA Astrophysics Data System (ADS)

Mahjoub, Mehdi

La resolution de l'equation de Boltzmann demeure une etape importante dans la prediction du comportement d'un reacteur nucleaire. Malheureusement, la resolution de cette equation presente toujours un defi pour une geometrie complexe (reacteur) tout comme pour une geometrie simple (cellule). Ainsi, pour predire le comportement d'un reacteur nucleaire,un schema de calcul a deux etapes est necessaire. La premiere etape consiste a obtenir les parametres nucleaires d'une cellule du reacteur apres une etape d'homogeneisation et condensation. La deuxieme etape consiste en un calcul de diffusion pour tout le reacteur en utilisant les resultats de la premiere etape tout en simplifiant la geometrie du reacteur a un ensemble de cellules homogenes le tout entoure de reflecteur. Lors des transitoires (accident), ces deux etapes sont insuffisantes pour pouvoir predire le comportement du reacteur. Comme la resolution de l'equation de Boltzmann dans sa forme dependante du temps presente toujours un defi de taille pour tous types de geometries,un autre schema de calcul est necessaire. Afin de contourner cette difficulte, l'hypothese adiabatique est utilisee. Elle se concretise en un schema de calcul a quatre etapes. La premiere et deuxieme etapes demeurent les memes pour des conditions nominales du reacteur. La troisieme etape se resume a obtenir les nouvelles proprietes nucleaires de la cellule a la suite de la perturbation pour les utiliser, au niveau de la quatrieme etape, dans un nouveau calcul de reacteur et obtenir l'effet de la perturbation sur le reacteur. Ce projet vise a verifier cette hypothese. Ainsi, un nouveau schema de calcul a ete defini. La premiere etape de ce projet a ete de creer un nouveau logiciel capable de resoudre l'equation de Boltzmann dependante du temps par la methode stochastique Monte Carlo dans le but d'obtenir des sections efficaces qui evoluent dans le temps. Ce code a ete utilise pour simuler un accident LOCA dans un reacteur nucleaire de type CANDU-6. Les sections efficaces dependantes du temps ont ete par la suite utilisees dans un calcul de diffusion espace-temps pour un reacteur CANDU-6 subissant un accident de type LOCA affectant la moitie du coeur afin d'observer son comportement durant toutes les phases de la perturbation. Dans la phase de developpement, nous avons choisi de demarrer avec le code OpenMC, developpe au MIT,comme plateforme initiale de developpement. L'introduction et le traitement des neutrons retardes durant la simulation ont presente un grand defi a surmonter. Il est important de noter que le code developpe utilisant la methode Monte Carlo peut etre utilise a grande echelle pour la simulation de tous les types des reacteurs nucleaires si les supports informatiques sont disponibles.

Joy Development Properties, LLC, Pleasant Valley, Iowa and Summit Concrete, Inc., LeClaire, Iowa - Clean Water Act Public Notice

EPA Pesticide Factsheets

The EPA is providing notice of a proposed Administrative Penalty Assessment against Joy Development Properties, LLC and Summit Concrete, Inc., for alleged violations at the companies’ residential construction site known as the Schutter Farms Addition loca

The art in getting flocks and herds to flerds

USDA-ARS?s Scientific Manuscript database

Flerds (small ruminants that consistently stay near cattle under free-ranging conditions) offer four distinct advantages over stocking simply flocks and herds to carry out mixed species stocking. One of the main advantages flerds offer is added protection from canine predation, reduced time in loca...

False Memories for Shape Activate the Lateral Occipital Complex

ERIC Educational Resources Information Center

Karanian, Jessica M.; Slotnick, Scott D.

2017-01-01

Previous functional magnetic resonance imaging evidence has shown that false memories arise from higher-level conscious processing regions rather than lower-level sensory processing regions. In the present study, we assessed whether the lateral occipital complex (LOC)--a lower-level conscious shape processing region--was associated with false…

AROMATASE ACTIVITY IN THE OVARY OF MOSQUITOFISH GAMBUSIA HOLBROOKI, COLLECTED FROM THE FENHOLLOWAY AND ECONFINA RIVERS, FLORIDA (

EPA Science Inventory

Scientists are increasingly aware of the adverse effects of environmental contaminants, including their ability to alter the normal development and reproduction of wildlife species by modifying the endocrine system. Female mosquitofish living downstream of a paper mill plant loca...

Non-condensable gas effects in ROSA/AP600 small-break LOCA experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakamura, Hideo; Kukita, Yutaka; Shaw, R.A.

1996-06-01

Integral experiments simulating the postulated accidents in the Westinghouse AP600 reactor have been conducted using the ROSA-V Large Scale Test Facility (LSTF). These experiments allowed the N{sub 2} gas for the pressurization of accumulator tanks to enter the primary system after the depletion of the tank water inventory. The gas migrated into the Passive Residual Heat Removal (PRHR) system heat exchanger tubes and into the Core Makeup Tanks (CMTs), and influenced the performance of these components which are unique to the AP600 reactor. Specifically, the PRHR was disabled soon after the N{sub 2} gas discharge in most of the experiments,more » although the core decay power was removed well by the steam discharge through the Automatic Depressurization System (ADS) after the PRHR was disabled. The N{sub 2} gas ingress into the CMTs occurred in the experiments with relatively large breaks ({ge} 2 inch in equivalent diameter), and contributed to a smooth draindown of the CMT inventory into the primary system.« less

LOFA analysis in helium and Pb-Li circuits of LLCB TBM by FE simulation

NASA Astrophysics Data System (ADS)

Chaudhuri, Paritosh; Ranjithkumar, S.; Sharma, Deepak; Danani, Chandan

2017-04-01

One of the main ITER objectives is to demonstrate the feasibility of the breeding blanket concepts that would lead to tritium self-sufficiency and the extraction of a high-grade heat for electricity production. India has developed the LLCB TBM to be tested in ITER for the validation of design concepts for tritium breeding blankets relevant DEMO and future power reactor. LLCB concept has the unique features of combination of both solid (lithium titanate as packed pebble bed) and liquid breeders (molten lead lithium). India specific IN-RAFMS is the structural material for TBM. The First Wall is actively cooled by high-pressure helium (He) gas [1]. It is important to validate the design of TBM to withstand various loads acting on it including accident analysis like LOCA, LOFA etc. Detailed thermal-hydraulic simulation studies including LOFA in helium and Pb-Li circuits of LLCB TBM have been performed using Finite Element using ANSYS. These analyses will provide important information about the temperature distribution in different materials used in TBM during steady state and transient condition. Thermal-hydraulic safety requirement has also been envisaged for the initiation the FPPS (Fusion Power Shutdown System) during LOFA. All these analysis will be presented in detail in this paper.

A complete dosimetry experimental program in support to the core characterization and to the power calibration of the CABRI reactor. A complete dosimetry experimental program in support of the core characterization and of the power calibration of the CABRI reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodiac, F.; Hudelot, JP.; Lecerf, J.

CABRI is an experimental pulse reactor operated by CEA at the Cadarache research center. Since 1978 the experimental programs have aimed at studying the fuel behavior under Reactivity Initiated Accident (RIA) conditions. Since 2003, it has been refurbished in order to be able to provide RIA and LOCA (Loss Of Coolant Accident) experiments in prototypical PWR conditions (155 bar, 300 deg. C). This project is part of a broader scope including an overall facility refurbishment and a safety review. The global modification is conducted by the CEA project team. It is funded by IRSN, which is conducting the CIP experimentalmore » program, in the framework of the OECD/NEA project CIP. It is financed in the framework of an international collaboration. During the reactor restart, commissioning tests are realized for all equipment, systems and circuits of the reactor. In particular neutronics and power commissioning tests will be performed respectively in 2015 and 2016. This paper focuses on the design of a complete and original dosimetry program that was built in support to the CABRI core characterization and to the power calibration. Each one of the above experimental goals will be fully described, as well as the target uncertainties and the forecasted experimental techniques and data treatment. (authors)« less

Multitarget Tracking Studies.

DTIC Science & Technology

1981-07-01

ie "n.: r c:.t. ’ur wn Le r":2- ence Indistes :nac pole a n :arc loca- 40 ":Lors !AVe a sinificant effect n convergence raes.- .ahdn te poles and...LATTICE ALGORITHMS ( LADO ) 1. The Normalized AR Lattice (ARN) This algorithm implements the normalized algorithm described in [23]. The AR coefficients are

77 FR 53923 - Biweekly Notice;

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-04

... to be publicly disclosed. The NRC posts all comment submissions at http://www.regulations.gov as well... (psig) to 49.7 psig for the design basis loss-of- coolant accident (LOCA). In support of the revised P a... analysis. The P a remains below the containment design pressure of 50 psig because of the change in the...

Effect of sampling location on L* values and pH measurements and their relationship in broiler breast fillets

USDA-ARS?s Scientific Manuscript database

Lightness (CIELAB L*) and pH values are the most widely measured quality indicators for broiler breast fillets (pectoralis major). Measurement of L* values with a spectrophotometer can be done through Specular Component Included (SCI) or Specular Component Excluded (SCE) modes. The intra-fillet loca...

A combination of sexual and ecological divergence contributes to the spread of a chromosomal rearrangement during initial stages of speciation

USDA-ARS?s Scientific Manuscript database

Chromosomal rearrangements between sympatric species often contain multiple loci contributing to assortative mating, local adaptation, and hybrid sterility. When and how these associations arise during the process of speciation remains a subject of debate. Here, we address the relative roles of loca...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Faidy, C.; Gilles, P.

The objective of the seminar was to present the current state of the art in Leak-Before-Break (LBB) methodology development, validation, and application in an international forum. With particular emphasis on industrial applications and regulatory policies, the seminar provided an opportunity to compare approaches, experiences, and codifications developed by different countries. The seminar was organized into four topic areas: status of LBB applications; technical issues in LBB methodology; complementary requirements (leak detection and inspection); LBB assessment and margins. As a result of this seminar, an improved understanding of LBB gained through sharing of different viewpoints from different countries, permits consideration of:more » simplified pipe support design and possible elimination of loss-of-coolant-accident (LOCA) mechanical consequences for specific cases; defense-in-depth type of applications without support modifications; support of safety cases for plants designed without the LOCA hypothesis. In support of these activities, better estimates of the limits to the LBB approach should follow, as well as an improvement in codifying methodologies. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.« less

Post-quench ductility evaluation of Zircaloy-4 and select iron alloys under design basis and extended LOCA conditions

NASA Astrophysics Data System (ADS)

Yan, Y.; Keiser, J. R.; Terrani, K. A.; Bell, G. L.; Snead, L. L.

2014-05-01

Oxidation experiments were conducted at 1200 °C in flowing steam with tubing specimens of Zircaloy-4, 317, 347 stainless steels, and the commercial FeCrAl alloy APMT. The purpose was to determine the oxidation behavior and post-quench ductility under postulated and extended LOCA conditions. The parabolic rate constant for Zircaloy-4 tubing samples at 1200 °C was determined to be k = 2.173 × 107 g2/cm4/s, in excellent agreement with the Cathcart-Pawel correlation. The APMT alloy experienced the slowest oxidation rate among all materials examined in this work. The ductility of post-quenched samples was evaluated by ring compression tests at 135 °C. For Zircaloy-4, the ductile to brittle transition occurs at an equivalent cladding reacted (ECR) of 19.3%. SS-347 was still ductile after being oxidized for 2400 s (CP-ECR ≈ 50%), but the maximum load was reduced significantly owing to the metal layer thickness reduction. No ductility decrease was observed for the post-quenched APMT samples oxidized up to 4 h.

Effects of short-term tocopherol (T) feeding on structure-localized protein tyrosine nitration (pTN) patterns of mitochondrial ATPase following endotoxin (LPS) challenge in beef calves.

USDA-ARS?s Scientific Manuscript database

Mitochondrial ATPase/Complex-V (MCV) is an electron transport chain (ETC) component needed for ATP synthesis. The ETC, exquisitely sensitive to proinflammatory mediators (PIM), generates oxynitrogen reactants leading to pTN formation as mitochondrial membrane leakage occurs. Immunohistochemical loca...

Evaluation of a barley core collection for spot form net blotch reaction reveals distinct genotype specific pathogen virulence and host susceptibility

USDA-ARS?s Scientific Manuscript database

Spot form net blotch (SFNB) caused by Pyrenophora teres Drechs. f. maculata Smedeg., (anamorph Drechslera teres [Sacc.] Shoem.) is a major foliar disease of barley (Hordeum vulgare L.) worldwide. SFNB epidemics have recently been observed in major barley producing countries, suggesting that the loca...

Modern Data Analysis techniques in Noise and Vibration Problems

DTIC Science & Technology

1981-11-01

Hilbert l’une de l’autre. Cette propriete se retrouve dans l’etude de la causalite : ce qui de- finit un critere pratique caracterisant un signal donc, par...entre Ie champ direct et Ie champ reflechi se caracterisent loca- lement par l’existence de frequences pour lesquelles l’interference est totale

Patient to Health Team Communications Preferences and Perceptions of Secure Messaging

DTIC Science & Technology

2017-04-25

Ellicott C itv MD, 25- 27 April 2017 in accordance with MDWI 4 1- 108, has been approved and assigned loca l fi le # 17202. 2. Pe11 inent biographic...scholarl y activities o f our professional staff and students, which is an essential component of Wi lford Hall Ambulatory Surgical Center (WHASC

Fabrication Control Plan for ORNL RH-LOCA ATF Test Specimens to be Irradiated in the ATR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Field, Kevin G.; Howard, Richard; Teague, Michael

2014-06-01

The purpose of this fabrication plan is (1) to summarize the design of a set of rodlets that will be fabricated and then irradiated in the Advanced Test Reactor (ATR) and (2) provide requirements for fabrication and acceptance criteria for inspections of the Light Water Reactor (LWR) – Accident Tolerant Fuels (ATF) rodlet components. The functional and operational (F&OR) requirements for the ATF program are identified in the ATF Test Plan. The scope of this document only covers fabrication and inspections of rodlet components detailed in drawings 604496 and 604497. It does not cover the assembly of these items tomore » form a completed test irradiation assembly or the inspection of the final assembly, which will be included in a separate INL final test assembly specification/inspection document. The controls support the requirements that the test irradiations must be performed safely and that subsequent examinations must provide valid results.« less

The IRIS Spool-Type Reactor Coolant Pump

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kujawski, J.M.; Kitch, D.M.; Conway, L.E.

2002-07-01

IRIS (International Reactor Innovative and Secure) is a light water cooled, 335 MWe power reactor which is being designed by an international consortium as part of the US DOE NERI Program. IRIS features an integral reactor vessel that contains all the major reactor coolant system components including the reactor core, the coolant pumps, the steam generators and the pressurizer. This integral design approach eliminates the large coolant loop piping, and thus eliminates large loss-of-coolant accidents (LOCAs) as well as the individual component pressure vessels and supports. In addition, IRIS is being designed with a long life core and enhanced safetymore » to address the requirements defined by the US DOE for Generation IV reactors. One of the innovative features of the IRIS design is the adoption of a reactor coolant pump (called 'spool' pump) which is completely contained inside the reactor vessel. Background, status and future developments of the IRIS spool pump are presented in this paper. (authors)« less

Improved National Response to Climate Change: Aligning USGCRP reports and the U.S. Climate Resilience Toolkit

NASA Astrophysics Data System (ADS)

Lipschultz, F.; Dahlman, L. E.; Herring, D.; Fox, J. F.

2017-12-01

As part of an effort to coordinate production and distribution of scientific climate information across the U.S. Government, and to spur adaptation actions across the nation, the U.S. Global Change Research Program (USGCRP) has worked to better integrate the U.S. Climate Resilience Toolkit (CRT) and its Climate Explorer (CE) tool into USGCRP activities and products. Much of the initial CRT content was based on the Third National Climate Assessment (NCA3). The opportunity to integrate current development of NCA4—scheduled for release in late 2018—with CRT and CE can enhance all three projects and result in a useable and "living" NCA that is part of USGCRP's approach to sustained climate assessment. To coordinate this work, a USGCRP-led science team worked with CRT staff and CE developers to update the set of climate projections displayed in the CE tool. In concert with the USGCRP scenarios effort, the combined team selected the Localized Constructed Analogs (LOCA) dataset for the updated version of CE, based on its capabilities for capturing climate extremes and local climate variations. The team identified 28 variables from the LOCA dataset for display in the CE; many of these variables will also be used in USGCRP reports. In CRT engagements, communities with vulnerable assets have expressed a high value for the ability to integrate climate data available through the CE with data related to non-climate stressors in their locations. Moving forward, the teams intend to serve climate information needs at additional spatial scales by making NCA4 content available via CE's capability for dynamic interaction with climate-relevant datasets. This will permit users to customize the extent of data they access for decision-making, starting with the static NCA4 report. Additionally, NCA4 case studies and other content can be linked to more in-depth content within the CRT site. This capability will enable more frequent content updates than can be managed with quadrennial NCA reports. Overall, enhanced integration between USGCRP and CRT will provide consistent information for communities that are assessing their climate vulnerabilities or considering adaptation options.

Strategy and Airpower

DTIC Science & Technology

2011-01-01

myopia often leads otherwise competent observers to under­ estimate significantly the new technology’s potential. Two business examples stand out: in...direction. With precision of effect combined with precision of impact, bloodless war becomes a reality . To this point, we have tried to make the...against virtually all of the centers of gravity directly related to strategic objectives, regardless of their loca­ tion. Because it can bring many

Models and numerical methods for the simulation of loss-of-coolant accidents in nuclear reactors

NASA Astrophysics Data System (ADS)

Seguin, Nicolas

2014-05-01

In view of the simulation of the water flows in pressurized water reactors (PWR), many models are available in the literature and their complexity deeply depends on the required accuracy, see for instance [1]. The loss-of-coolant accident (LOCA) may appear when a pipe is broken through. The coolant is composed by light water in its liquid form at very high temperature and pressure (around 300 °C and 155 bar), it then flashes and becomes instantaneously vapor in case of LOCA. A front of liquid/vapor phase transition appears in the pipes and may propagate towards the critical parts of the PWR. It is crucial to propose accurate models for the whole phenomenon, but also sufficiently robust to obtain relevant numerical results. Due to the application we have in mind, a complete description of the two-phase flow (with all the bubbles, droplets, interfaces…) is out of reach and irrelevant. We investigate averaged models, based on the use of void fractions for each phase, which represent the probability of presence of a phase at a given position and at a given time. The most accurate averaged model, based on the so-called Baer-Nunziato model, describes separately each phase by its own density, velocity and pressure. The two phases are coupled by non-conservative terms due to gradients of the void fractions and by source terms for mechanical relaxation, drag force and mass transfer. With appropriate closure laws, it has been proved [2] that this model complies with all the expected physical requirements: positivity of densities and temperatures, maximum principle for the void fraction, conservation of the mixture quantities, decrease of the global entropy… On the basis of this model, it is possible to derive simpler models, which can be used where the flow is still, see [3]. From the numerical point of view, we develop new Finite Volume schemes in [4], which also satisfy the requirements mentioned above. Since they are based on a partial linearization of the physical model, this numerical scheme is also efficient in terms of CPU time. Eventually, simpler models can locally replace the more complex model in order to simplify the overall computation, using some appropriate local error indicators developed in [5], without reducing the accuracy. References 1. Ishii, M., Hibiki, T., Thermo-fluid dynamics of two-phase flow, Springer, New-York, 2006. 2. Gallouët, T. and Hérard, J.-M., Seguin, N., Numerical modeling of two-phase flows using the two-fluid two-pressure approach, Math. Models Methods Appl. Sci., Vol. 14, 2004. 3. Seguin, N., Étude d'équations aux dérivées partielles hyperboliques en mécanique des fluides, Habilitation à diriger des recherches, UPMC-Paris 6, 2011. 4. Coquel, F., Hérard, J-M., Saleh, K., Seguin, N., A Robust Entropy-Satisfying Finite Volume Scheme for the Isentropic Baer-Nunziato Model, ESAIM: Mathematical Modelling and Numerical Analysis, Vol. 48, 2013. 5. Mathis, H., Cancès, C., Godlewski, E., Seguin, N., Dynamic model adaptation for multiscale simulation of hyperbolic systems with relaxation, preprint, 2013.

Atmospheric Models For Over-Ocean Propagation Loss

DTIC Science & Technology

2015-08-24

Radiosonde balloons are launched daily at selected loca- tions, and measure temperature, dew point temperature, and air pressure as they ascend. Radiosondes...different times of year and locations. The result was used to estimate high-reliability SHF/EHF air -to-surface radio link performance in a maritime...environment. I. INTRODUCTION Air -to-surface radio links differ from typical satellite com- munications links in that the path elevation angles are lower

Fluid Dynamic Analysis of Volcanic Tremor,

DTIC Science & Technology

1982-10-01

information regarding the fluid system Fiske (1969) Kilauea volcano : The 1967-68 summit configuration, tremor magnitudes and source loca- eruption...Koyanagi (1981) Deep volcanic tremor logicalSociety of America, vol. 40, p. 175-194. and magma ascent mechanism under Kilauea , Hawaii . Omori, F...dynamics Seismology Tremors Volcanoes 40 M\\ TlACT (amhue ai revers if5 neeeeiy md ide~Wify by block number) Low-frequency (< 10 Hz) volcanic earthquakes

Safety margins in zircaloy oxidation and embrittlement criteria for emergency core cooling system acceptance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williford, R.E.

1986-09-01

Current emergency core cooling system acceptance criteria for light water reactors specify that, under loss-of-coolant accident (LOCA) conditions, the Baker-Just (BJ) correlation must be used to calculate Zircaloy-steam oxidation, calculated peak cladding temperatures (PCT) must not exceed 1204/sup 0/C, and calculated oxidation must not exceed 17% equivalent cladding reacted (ECR). An appropriately defined minimum margin of safety was estimated for each of these criteria. The currently required BJ oxidation correlation provides margins only over the 1100 to 1500/sup 0/C temperature range at the 95% confidence level. The PCT margins for thermal shock and handling failures are adequate at oxidation temperaturesmore » above 1204/sup 0/C for up to 210 and 160 s, respectively, at the 95% confidence level. The ECR thermal shock and handling margins at the 50 and 95% confidence levels, respectively, range between 2 and 7% ECR for the BJ correlation, but vanish at temperatures above 1100 to 1160/sup 0/C for the best-estimate Cathcart-Pawel correlation. However, use of the Cathcart Pawel correlation for ''design basis'' LOCA calculations can be justified at the 85 to 88% confidence level if cooling rate effects can be neglected.« less

Analysis of Loss-of-Coolant Accidents in the NIST Research Reactor - Early Phase

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baek, Joo S.; Diamond, David

A study of the fuel temperature during the early phase of a loss-of-coolant accident (LOCA) in the NIST research reactor (NBSR) was completed. Previous studies had been reported in the preliminary safety analysis report for the conversion of the NBSR from high-enriched uranium (HEU) fuel to low-enriched (LEU) fuel. Those studies had focused on the most vulnerable LOCA situation, namely, a double-ended guillotine break in the time period after reactor trip when water is drained from either the coolant channels inside the fuel elements or the region outside the fuel elements. The current study fills in a gap in themore » analysis which is the early phase of the event when there may still be water present but the reactor is at power or immediately after reactor trip and pumps have tripped. The calculations were done, for both the current HEU-fueled core and the proposed LEU core, with the TRACE thermal-hydraulic systems code. Several break locations and different break sizes were considered. In all cases the increase in the clad (or fuel meat) temperature was relatively small so that a large margin to the temperature threshold for blistering (the Safety Limit for the NBSR) remained.« less

A review for identification of initiating events in event tree development process on nuclear power plants

NASA Astrophysics Data System (ADS)

Riyadi, Eko H.

2014-09-01

Initiating event is defined as any event either internal or external to the nuclear power plants (NPPs) that perturbs the steady state operation of the plant, if operating, thereby initiating an abnormal event such as transient or loss of coolant accident (LOCA) within the NPPs. These initiating events trigger sequences of events that challenge plant control and safety systems whose failure could potentially lead to core damage or large early release. Selection for initiating events consists of two steps i.e. first step, definition of possible events, such as by evaluating a comprehensive engineering, and by constructing a top level logic model. Then the second step, grouping of identified initiating event's by the safety function to be performed or combinations of systems responses. Therefore, the purpose of this paper is to discuss initiating events identification in event tree development process and to reviews other probabilistic safety assessments (PSA). The identification of initiating events also involves the past operating experience, review of other PSA, failure mode and effect analysis (FMEA), feedback from system modeling, and master logic diagram (special type of fault tree). By using the method of study for the condition of the traditional US PSA categorization in detail, could be obtained the important initiating events that are categorized into LOCA, transients and external events.

Final Report on ITER Task Agreement 81-08

DOE Office of Scientific and Technical Information (OSTI.GOV)

Richard L. Moore

As part of an ITER Implementing Task Agreement (ITA) between the ITER US Participant Team (PT) and the ITER International Team (IT), the INL Fusion Safety Program was tasked to provide the ITER IT with upgrades to the fusion version of the MELCOR 1.8.5 code including a beryllium dust oxidation model. The purpose of this model is to allow the ITER IT to investigate hydrogen production from beryllium dust layers on hot surfaces inside the ITER vacuum vessel (VV) during in-vessel loss-of-cooling accidents (LOCAs). Also included in the ITER ITA was a task to construct a RELAP5/ATHENA model of themore » ITER divertor cooling loop to model the draining of the loop during a large ex-vessel pipe break followed by an in-vessel divertor break and compare the results to a simular MELCOR model developed by the ITER IT. This report, which is the final report for this agreement, documents the completion of the work scope under this ITER TA, designated as TA 81-08.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourham, Mohamed A.; Gilligan, John G.

Safety considerations in large future fusion reactors like ITER are important before licensing the reactor. Several scenarios are considered hazardous, which include safety of plasma-facing components during hard disruptions, high heat fluxes and thermal stresses during normal operation, accidental energy release, and aerosol formation and transport. Disruption events, in large tokamaks like ITER, are expected to produce local heat fluxes on plasma-facing components, which may exceed 100 GW/m{sup 2} over a period of about 0.1 ms. As a result, the surface temperature dramatically increases, which results in surface melting and vaporization, and produces thermal stresses and surface erosion. Plasma-facing componentsmore » safety issues extends to cover a wide range of possible scenarios, including disruption severity and the impact of plasma-facing components on disruption parameters, accidental energy release and short/long term LOCA's, and formation of airborne particles by convective current transport during a LOVA (water/air ingress disruption) accident scenario. Study, and evaluation of, disruption-induced aerosol generation and mobilization is essential to characterize database on particulate formation and distribution for large future fusion tokamak reactor like ITER. In order to provide database relevant to ITER, the SIRENS electrothermal plasma facility at NCSU has been modified to closely simulate heat fluxes expected in ITER.« less

Fallon Geothermal Exploration Project, Naval Air Station, Fallon, Nevada.

DTIC Science & Technology

1980-05-01

magneto- telluric studies. LINEAMENT ANALYSIS As part of the initial phase of the Fallon Exploration Project, a composite lineament analysis of the region...Nevada. United States Geological Survey Bulletin 750, 1924, pp. 79-86. Hoover, D. B., R. M. Senterfit, and Bruce Radtke. Telluric Profile Loca- tion...Map and Telluric Data for the Salt Wells Known Geothermal Resource Area, Nevada. United States Geological Survey Open File Report 77-66F, 1977. Horton

The California Debris Commission: A History

DTIC Science & Technology

1981-01-01

the pipe a more freely in the horizontal plane, while vertical elastic packing in the joint instead of two stable instrument to handle. movement was...report of January duplicate and triplicate taxation , and (4) it 1880 painted a dark and sobering picture Following two months of intense and had not the...isolated cases it is possible to impound debris without injury; also, that loca- tions exist in the canons of the different mining streams in the Sierra

The Effects of Alarm Display, Processing, and Availability on Crew Performance

DTIC Science & Technology

2000-11-01

snow Instrumentation line leakage Small LOCA Steam generator tube rupture Small feedwater leakage inside containment Cycling of main steam...implemented. • Due to primary pressure controller failure, pressure heater banks cycle between on and off. 8.00 CF1 CF2 CF3 CF4 CF5...temperatures after the high-pressure pre- heaters flows into the steam generators number of active emergency feedwater pumps openings of the condensate

Operation TEAPOT. Report of the Test Manager Joint Test Organization

DTIC Science & Technology

1981-11-01

Analysis of air, water, and milk samples were made at the laboratory at Mercury. z. 6.4 MONITORING PROCEDURES A mobile surface monitoring group consisting o...additional weather observations proved very use- ful in weather analysis and forecasting as well as for monitoring winds aloft prior to shot time. The...data were also valuable in post analysis for accurate plotting of fallout and determining cloud trajectories. The loca- tion and type of operations of

Better Vision Through Manipulation

DTIC Science & Technology

2002-01-01

correlation can be used as a "signature" to iden- map useful for generating arm, head, and trunk tify parts of the scene that are being influenced by...down reaching. This can be over- in response to the nudge of the arm. This move- come by training up a function to estimate the loca- ment will be... behavioural evidence. Experimental Gibson, J. J. (1977). The theory of affordances. Brain Research, 143:335-341. In Shaw, R. and Bransford, J., (Eds

Particle Size Determination in Small Solid Propellant Rocket Motors Using the Diffractively Scattered Light Method.

DTIC Science & Technology

1982-10-01

calibrated by using spherical glass beads and aluminum oxide powder . Measurements were successfully made at both locations. Because DO 1473 EoITioN OF I NOVy...determined using measurements of diffrac- tively scattered laser power spectra. The apparatus was calibrated by using spherical glass beads and aluminum oxide... powder . Measurements were successfully made at both loca- tions. Because of the presence of char agglomerates in the exhaust, continued effort is

Core-power and decay-time limits for disabled automatic-actuation of LOFT ECCS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, G.H.

1978-11-22

The Emergency Core Cooling System (ECCS) for the LOFT reactor may need to be disabled for modifications or repairs of hardware or instrumentation or for component testing during periods when the reactor system is hot and pressurized, or it may be desirable to enable the ECCS to be disabled without the necessity of cooling down and depressurizing the reactor. A policy involves disabling the automatic-actuation of the LOFT ECCS, but still retaining the manual actuation capability. Disabling of the automatic actuation can be safely utilized, without subjecting the fuel cladding to unacceptable temperatures, when the LOFT power decays to 33more » kW; this power level permits a maximum delay of 20 minutes following a LOCA for the manual actuation of ECCS. For the operating power of the L2-2 Experiment, the required decay-periods (with operating periods of 40 and 2000 hours) are about 21 and 389 hours, respectively. With operating periods of 40 and 2000 hours at Core-I full power, the required decay-periods are about 42 and 973 hours, respectively. After these decay periods the automatic actuation of the LOFT ECCS can be disabled assuming a maximum delay of 20 minutes following a LOCA for the manual actuation of ECCS. The automatic and manual lineup of the ECCS may be waived if decay power is less than 11 kW.« less

A review for identification of initiating events in event tree development process on nuclear power plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Riyadi, Eko H., E-mail: e.riyadi@bapeten.go.id

2014-09-30

Initiating event is defined as any event either internal or external to the nuclear power plants (NPPs) that perturbs the steady state operation of the plant, if operating, thereby initiating an abnormal event such as transient or loss of coolant accident (LOCA) within the NPPs. These initiating events trigger sequences of events that challenge plant control and safety systems whose failure could potentially lead to core damage or large early release. Selection for initiating events consists of two steps i.e. first step, definition of possible events, such as by evaluating a comprehensive engineering, and by constructing a top level logicmore » model. Then the second step, grouping of identified initiating event's by the safety function to be performed or combinations of systems responses. Therefore, the purpose of this paper is to discuss initiating events identification in event tree development process and to reviews other probabilistic safety assessments (PSA). The identification of initiating events also involves the past operating experience, review of other PSA, failure mode and effect analysis (FMEA), feedback from system modeling, and master logic diagram (special type of fault tree). By using the method of study for the condition of the traditional US PSA categorization in detail, could be obtained the important initiating events that are categorized into LOCA, transients and external events.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walston, S; Rowland, M; Campbell, K

It is difficult to track to the location of a melted core in a GE BWR with Mark I containment during a beyond-design-basis accident. The Cooper Nuclear Station provided a baseline of normal material distributions and shielding configurations for the GE BWR with Mark I containment. Starting with source terms for a design-basis accident, methods and remote observation points were investigated to allow tracking of a melted core during a beyond-design-basis accident. The design of the GE BWR with Mark-I containment highlights an amazing poverty of expectations regarding a common mode failure of all reactor core cooling systems resulting inmore » a beyond-design-basis accident from the simple loss of electric power. This design is shown in Figure 1. The station blackout accident scenario has been consistently identified as the leading contributor to calculated probabilities for core damage. While NRC-approved models and calculations provide guidance for indirect methods to assess core damage during a beyond-design-basis loss-of-coolant accident (LOCA), there appears to be no established method to track the location of the core directly should the LOCA include a degree of fuel melt. We came to the conclusion that - starting with detailed calculations which estimate the release and movement of gaseous and soluble fission products from the fuel - selected dose readings in specific rooms of the reactor building should allow the location of the core to be verified.« less

Severe Accident Scoping Simulations of Accident Tolerant Fuel Concepts for BWRs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robb, Kevin R.

2015-08-01

Accident-tolerant fuels (ATFs) are fuels and/or cladding that, in comparison with the standard uranium dioxide Zircaloy system, can tolerate loss of active cooling in the core for a considerably longer time period while maintaining or improving the fuel performance during normal operations [1]. It is important to note that the currently used uranium dioxide Zircaloy fuel system tolerates design basis accidents (and anticipated operational occurrences and normal operation) as prescribed by the US Nuclear Regulatory Commission. Previously, preliminary simulations of the plant response have been performed under a range of accident scenarios using various ATF cladding concepts and fully ceramicmore » microencapsulated fuel. Design basis loss of coolant accidents (LOCAs) and station blackout (SBO) severe accidents were analyzed at Oak Ridge National Laboratory (ORNL) for boiling water reactors (BWRs) [2]. Researchers have investigated the effects of thermal conductivity on design basis accidents [3], investigated silicon carbide (SiC) cladding [4], as well as the effects of ATF concepts on the late stage accident progression [5]. These preliminary analyses were performed to provide initial insight into the possible improvements that ATF concepts could provide and to identify issues with respect to modeling ATF concepts. More recently, preliminary analyses for a range of ATF concepts have been evaluated internationally for LOCA and severe accident scenarios for the Chinese CPR1000 [6] and the South Korean OPR-1000 [7] pressurized water reactors (PWRs). In addition to these scoping studies, a common methodology and set of performance metrics were developed to compare and support prioritizing ATF concepts [8]. A proposed ATF concept is based on iron-chromium-aluminum alloys (FeCrAl) [9]. With respect to enhancing accident tolerance, FeCrAl alloys have substantially slower oxidation kinetics compared to the zirconium alloys typically employed. During a severe accident, FeCrAl would tend to generate heat and hydrogen from oxidation at a slower rate compared to the zirconium-based alloys in use today. The previous study, [2], of the FeCrAl ATF concept during station blackout (SBO) severe accident scenarios in BWRs was based on simulating short term SBO (STSBO), long term SBO (LTSBO), and modified SBO scenarios occurring in a BWR-4 reactor with MARK-I containment. The analysis indicated that FeCrAl had the potential to delay the onset of fuel failure by a few hours depending on the scenario, and it could delay lower head failure by several hours. The analysis demonstrated reduced in-vessel hydrogen production. However, the work was preliminary and was based on limited knowledge of material properties for FeCrAl. Limitations of the MELCOR code were identified for direct use in modeling ATF concepts. This effort used an older version of MELCOR (1.8.5). Since these analyses, the BWR model has been updated for use in MELCOR 1.8.6 [10], and more representative material properties for FeCrAl have been modeled. Sections 2 4 present updated analyses for the FeCrAl ATF concept response during severe accidents in a BWR. The purpose of the study is to estimate the potential gains afforded by the FeCrAl ATF concept during BWR SBO scenarios.« less

RELAP5 Analyses of OECD/NEA ROSA-2 Project Experiments on Intermediate-Break LOCAs at Hot Leg or Cold Leg

NASA Astrophysics Data System (ADS)

Takeda, Takeshi; Maruyama, Yu; Watanabe, Tadashi; Nakamura, Hideo

Experiments simulating PWR intermediate-break loss-of-coolant accidents (IBLOCAs) with 17% break at hot leg or cold leg were conducted in OECD/NEA ROSA-2 Project using the Large Scale Test Facility (LSTF). In the hot leg IBLOCA test, core uncovery started simultaneously with liquid level drop in crossover leg downflow-side before loop seal clearing (LSC) induced by steam condensation on accumulator coolant injected into cold leg. Water remained on upper core plate in upper plenum due to counter-current flow limiting (CCFL) because of significant upward steam flow from the core. In the cold leg IBLOCA test, core dryout took place due to rapid liquid level drop in the core before LSC. Liquid was accumulated in upper plenum, steam generator (SG) U-tube upflow-side and SG inlet plenum before the LSC due to CCFL by high velocity vapor flow, causing enhanced decrease in the core liquid level. The RELAP5/MOD3.2.1.2 post-test analyses of the two LSTF experiments were performed employing critical flow model in the code with a discharge coefficient of 1.0. In the hot leg IBLOCA case, cladding surface temperature of simulated fuel rods was underpredicted due to overprediction of core liquid level after the core uncovery. In the cold leg IBLOCA case, the cladding surface temperature was underpredicted too due to later core uncovery than in the experiment. These may suggest that the code has remaining problems in proper prediction of primary coolant distribution.

ENcentive: A Framework for Intelligent Marketing in Mobile Peer-To-Peer Environments

DTIC Science & Technology

2005-01-01

trade and commu- nication strategies, mobile electronic marketing, intelligent agents, collaborative eCommerce 1. INTRODUCTION With the explosion of...requests the promotion (since Jeff is a cof- fee drinker). MH2 signs the promotion with Susan’s eN- centive ID. At 6pm, Jeff decides to take advantage of the...to become valid, a user has a choice of remaining in his current loca- tion and being able to take advantage of the promotion. The eNcentive Ad

Predicting the Behavior of Asphalt Concrete Pavements in Seasonal Frost Areas Using Nondestructive Techniques

DTIC Science & Technology

1990-11-01

and psychrometers : the loca- cm-diameter wooden dowel approximately 122 cm in tion of these gauges is shown in Figure 16. The length, with 4.0-mm holes...thermocouple psychrometers were the third Dowel set of sensors used. A detailed description of these sensors can be found in a paper by Brown and...Figure 19. Freezing of test sections. in resistance with temperature in TS 2. Major changes psychrometers were not evaluated for this report. These in

The history of Fort Leavenworth, 1937 - 1951

DTIC Science & Technology

1951-01-01

research assistance on the bibliography and some of the appendixes; Public Library, Leaven- worth, Kansas, for use of facilities; M~r. Cleve Williams for...througho4t (Act or Cometition s ged by Loca Citizens)its active ser~iice on a Snake River run, from Pocatello, Idaho , north to (Act or Cmpetitio s aged y...Post as usual 35th Division and Maj Gen William K. Herndon on June 9, 1940. A few days later the War of the 24th Division, National Guard, were on

Development of Facility Type Information Packages for Design of Air Force Facilities.

DTIC Science & Technology

1983-03-01

solution. For example, the optimum size and loca- 19 tion of windows for the incorporation of a passive solar *l . heating system varies with location, time...conditioning load estimate M. Energy impact statement N. Majcom review comments 0. Solar energy systems 61 4 Information which could help in the development...and Passive solar systems. All facilities should have Scme aspects of passive solar incor- por3ted into the iesign. Active sclar systems should ze con

A Steady State and Dynamic Analysis of a Mooring System.

DTIC Science & Technology

1977-03-25

drag on subsurface buoy Dx«, »y«» Dzs Cable drag eoaponants in esble coordinates *A Distance between calculated location and actual loca- tion of...ship Be Modulus of elasticity of esble fh Highest natural frequency of systea 0 Horizontal distance between snshor and ship -- MUIIM—laSHS...TQD Tension in esble fron ahlp st subsurface buoy TBB Tension in cable fron anchor at aubaurfaea buoy Ty" Tension In n’th esble segaent Hif|l

Reconstruction of Acoustic Exposure on Orcas in Haro Strait

DTIC Science & Technology

2009-01-01

Resident killer whales (Orcinus orca) (J pod).1 The class shadowed the J pod from their boat, recording its behavior, the GPS loca- tion of the...one of the resident pods of orcas, raising the question of the sonar’s impact on them. Due to two coincidental activities, this question can be...addressed in detail. Coinciding with Shoup’s transit, a marine mammal class from Friday Harbor Labs led by Dr. David Bain was observing a pod of Southern

Archeological Investigations in Cochiti Reservoir, New Mexico. Volume 2. Excavation and Analysis 1975 Season.

DTIC Science & Technology

1977-01-01

groups who used this ratio should be considered. them to process wild seeds and other vegeta material. The trough metate has been considered a specialized...transition and as an indi- was composed entirely of jar formswith wide oriface. cation of the importance assumed by wild vegetal ma- not as difficult to...For example. Ovis/Capra meat is con- faunal resource utilization from the excavated site loca- sidered most edible when the animal is young. Meat

International Workshop on Millimeter Waves (1992) Held in Orvieto, Italy on April 22-24, 1992

DTIC Science & Technology

1992-04-24

1fillinmler4Vtlatri Circuits T. Yotwymatiat. Receott IDeehotnns. #of NRI)-;,.,s. Te, impIig It. 11. Jamset. Adv’anced Design Tee hnu jues fir Leiear... designed for the sky radiation measurement. - consideration of typical flight altitudes of 300m to Its output delivers a mean-value of the relevant...Electrolytic Processes: Anodic, Etching and Cathodic -increase of Surface to Volume Ratio metal deponition. Loca-Stuctre epoitin b pont- ikea ) no damage

Design and Implementation of a Consolidated Airfield at McMurdo, Antarctica

DTIC Science & Technology

2014-09-01

DESTROY THIS REPORT WHEN NO LONGER NEEDED. DO NOT RETURN IT TO THE ORIGINATOR . ERDC/CRREL TR-14-22 iii Contents Abstract...the current loca- tion of the white ice runway (the wheeled runway at Pegasus) is about 1/3 mile WSW of where it was when it was originally ...ft below the surface. This is not surprising; when the original runway was established in 1991–92, there were regions where the ice needed to be

Current status of endoscopic simulation in gastroenterology fellowship training programs.

PubMed

Jirapinyo, Pichamol; Thompson, Christopher C

2015-07-01

Recent guidelines have encouraged gastroenterology and surgical training programs to integrate simulation into their core endoscopic curricula. However, the role that simulation currently has within training programs is unknown. This study aims to assess the current status of simulation among gastroenterology fellowship programs. This questionnaire study consisted of 38 fields divided into two sections. The first section queried program directors' experience on simulation and assessed the current status of simulation at their institution. The second portion surveyed their opinion on the potential role of simulation on the training curriculum. The study was conducted at the 2013 American Gastroenterological Association Training Directors' Workshop in Phoenix, Arizona. The participants were program directors from Accreditation Council for Graduate Medical Education accredited gastroenterology training programs, who attended the workshop. The questionnaire was returned by 69 of 97 program directors (response rate of 71%). 42% of programs had an endoscopic simulator. Computerized simulators (61.5%) were the most common, followed by mechanical (30.8%) and animal tissue (7.7%) simulators, respectively. Eleven programs (15%) required fellows to use simulation prior to clinical cases. Only one program has a minimum number of hours fellows have to participate in simulation training. Current simulators are deemed as easy to use (76%) and good educational tools (65%). Problems are cost (72%) and accessibility (69%). The majority of program directors believe that there is a need for endoscopic simulator training, with only 8% disagreeing. Additionally, a majority believe there is a role for simulation prior to initiation of clinical cases with 15% disagreeing. Gastroenterology fellowship program directors widely recognize the importance of simulation. Nevertheless, simulation is used by only 42% of programs and only 15% of programs require that trainees use simulation prior to clinical cases. No programs currently use simulation as part of the evaluation process.

Evaluating the influence of motor control on selective attention through a stochastic model: the paradigm of motor control dysfunction in cerebellar patient.

PubMed

Veneri, Giacomo; Federico, Antonio; Rufa, Alessandra

2014-01-01

Attention allows us to selectively process the vast amount of information with which we are confronted, prioritizing some aspects of information and ignoring others by focusing on a certain location or aspect of the visual scene. Selective attention is guided by two cognitive mechanisms: saliency of the image (bottom up) and endogenous mechanisms (top down). These two mechanisms interact to direct attention and plan eye movements; then, the movement profile is sent to the motor system, which must constantly update the command needed to produce the desired eye movement. A new approach is described here to study how the eye motor control could influence this selection mechanism in clinical behavior: two groups of patients (SCA2 and late onset cerebellar ataxia LOCA) with well-known problems of motor control were studied; patients performed a cognitively demanding task; the results were compared to a stochastic model based on Monte Carlo simulations and a group of healthy subjects. The analytical procedure evaluated some energy functions for understanding the process. The implemented model suggested that patients performed an optimal visual search, reducing intrinsic noise sources. Our findings theorize a strict correlation between the "optimal motor system" and the "optimal stimulus encoders."

In-situ tube burst testing and high-temperature deformation behavior of candidate materials for accident tolerant fuel cladding

DOE PAGES

Byun, Thak Sang; Yamamoto, Yukinori; Maloy, Stuart A.; ...

2015-08-25

Here, one of the most essential properties of accident tolerant fuel (ATF) for maintaining structural integrity during a loss-of-coolant accident (LOCA) is high resistance of the cladding to plastic deformation and burst failure, since the deformation and burst behavior governs the cooling efficiency of flow channels and the process of fission product release. To simulate and evaluate the deformation and burst process of thin-walled cladding, an in-situ testing and evaluation method has been developed on the basis of visual imaging and image analysis techniques. The method uses a specialized optics system consisting of a high-resolution video camera, a light filteringmore » unit, and monochromatic light sources. The in-situ testing is performed using a 50 mm long pressurized thin-walled tubular specimen set in a programmable furnace. As the first application, ten (10) candidate cladding materials for ATF, i.e., five FeCrAl alloys and five nanostructured steels, were tested using the newly developed method, and the time-dependent images were analyzed to produce detailed deformation and burst data such as true hoop stress, strain (creep) rate, and failure stress. Relatively soft FeCrAl alloys deformed and burst below 800 °C, while negligible strain rates were measured for higher strength alloys.« less

Assessment of safety margins in zircaloy oxidation and embrittlement criteria for ECCS acceptance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williford, R.E.

1986-04-01

Current Emergency Core Cooling System (ECCS) Acceptance Criteria for light-water reactors include certain requirements pertaining to calculations of core performance during a Loss of Coolant Accident (LOCA). The Baker-Just correlation must be used to calculate Zircaloy-steam oxidation, calculated peak cladding temperatures (PCT) must not exceed 1204/sup 0/C, and calculated oxidation must not exceed 17% equivalent cladding reacted (17% ECR). The minimum margin of safety was estimated for each of these criteria, based on research performed in the last decade. Margins were defined as the amounts of conservatism over and above the expected extreme values computed from the data base atmore » specified confidence levels. The currently required Baker-Just oxidation correlation provides margins only over the 1100/sup 0/C to 1500/sup 0/C temperature range at the 95% confidence level. The PCT margins for thermal shock and handling failures are adequate at oxidation temperatures above 1204/sup 0/C for 210 and 160 seconds, respectively, at the 95% confidence level. ECR thermal shock and handling margins at the 50% and 95% confidence levels, respectively, range between 2% and 7% ECR for the Baker-Just correlation, but vanish at temperatures between 1100/sup 0/C and 1160/sup 0/C for the best-estimate Cathcart-Pawel correlation. Use of the Cathcart-Pawel correlation for LOCA calculations can be justified at the 85% to 88% confidence level if cooling rate effects can be neglected. 75 refs., 21 figs.« less

APT Blanket Thermal Analyses of Top Horizontal Row 1 Modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shadday, M.A.

1999-09-20

The Accelerator Production of Tritium (APT) cavity flood system (CFS) is designed to be the primary safeguard for the integrity of the blanket modules during loss of coolant accidents (LOCAs). For certain large break LOCAs the CFS also provides backup for the residual heat removal systems (RHRs) in cooling the target assemblies. In the unlikely event that the internal flow passages in a blanket module or target assembly dryout, decay heat in the metal structures will be dissipated to the CFS through the module or assembly walls (i.e., rung outer walls). The target assemblies consist of tungsten targets encased inmore » steel conduits, and they can safely sustain high metal temperatures. Under internally dry conditions, the cavity flood fluid will cool the target assemblies with vigorous nucleate boiling on the external surfaces. However, the metal structures in the blanket modules consist of lead cladded in aluminum, and they have a long-term exposure temperature limit currently set to 150 degrees C. Simultaneous LOCAs in both the target and blanket heat removal systems (HRS) could result in dryout of the target ladders, as well as the horizontal blanket modules above the target. The cavity flood coolant would boil on the outside surfaces of the target ladder rungs, and the resultant steam could reduce the effectiveness of convection heat transfer from the blanket modules to the cavity flood coolant. A two-part analysis was conducted to ascertain if the cavity flood system can adequately cool the blanket modules above the targets, even when boiling is occurring on the outer surfaces of the target ladder rungs. The first part of the analysis was to model transient thermal conduction in the front top horizontal row 1 module (i.e. top horizontal modules nearest the incoming beam), while varying parametrically the convection heat transfer coefficient (htc) for the external surfaces exposed to the cavity flood flow. This part of the analysis demonstrated that the module could adequately conduct heat to the outer module surfaces, given reasonable values for the convection heat transfer coefficients. The second part of the analysis consisted of two-phase flow modeling of the natural circulation of the cavity flood fluid past the top modules. Slots in the top shield allow the cavity flood fluid to circulate. The required width for these slots, to prevent steam from backing up and blanketing the outer surfaces of the top modules, was determined.« less

An efficient modeling method for thermal stratification simulation in a BWR suppression pool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haihua Zhao; Ling Zou; Hongbin Zhang

2012-09-01

The suppression pool in a BWR plant not only is the major heat sink within the containment system, but also provides major emergency cooling water for the reactor core. In several accident scenarios, such as LOCA and extended station blackout, thermal stratification tends to form in the pool after the initial rapid venting stage. Accurately predicting the pool stratification phenomenon is important because it affects the peak containment pressure; and the pool temperature distribution also affects the NPSHa (Available Net Positive Suction Head) and therefore the performance of the pump which draws cooling water back to the core. Current safetymore » analysis codes use 0-D lumped parameter methods to calculate the energy and mass balance in the pool and therefore have large uncertainty in prediction of scenarios in which stratification and mixing are important. While 3-D CFD methods can be used to analyze realistic 3D configurations, these methods normally require very fine grid resolution to resolve thin substructures such as jets and wall boundaries, therefore long simulation time. For mixing in stably stratified large enclosures, the BMIX++ code has been developed to implement a highly efficient analysis method for stratification where the ambient fluid volume is represented by 1-D transient partial differential equations and substructures such as free or wall jets are modeled with 1-D integral models. This allows very large reductions in computational effort compared to 3-D CFD modeling. The POOLEX experiments at Finland, which was designed to study phenomena relevant to Nordic design BWR suppression pool including thermal stratification and mixing, are used for validation. GOTHIC lumped parameter models are used to obtain boundary conditions for BMIX++ code and CFD simulations. Comparison between the BMIX++, GOTHIC, and CFD calculations against the POOLEX experimental data is discussed in detail.« less

Development of an AFIT (Air Force Institute of Technology) ADP System Network Model.

DTIC Science & Technology

1983-12-01

printers. Lastly, after a batch event finishes ’printing’, the turnaround time for each computer and loca- tion may be collected. Resource Module. The...9)), + (IJOBSA(10)) ,(IORG,A( 12)) ,(,AEi4A( 13)) C CNNNN IF JOB JUST FINISHED CPU OR PRINTER IN WAIT MODE THEN SCHEDULE C**** THINK TINE C IF...Modules: CPUAIJ I C Scheduled by. none C C FUNCTION XIOSEC(ICLASSISIZE) P RAMETER (1AXCLS=6,WAXSIZ-6) C -’. CMII COPtION BLOCKS COtON /FACTOR/ DI STRB

Transfer of 45Ca and 36Cl at the blood-nerve barrier of the sciatic nerve in rats fed low or high calcium diets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wadhwani, K.C.; Murphy, V.A.; Rapoport, S.I.

1991-04-01

Unidirectional fluxes of 45Ca, 36Cl, and of (3H)mannitol from blood into the sciatic nerve and cerebral cortex were determined from 5- and 15-min uptakes of these tracers after an intravenous (i.v.) bolus injection in awake rats. Rats were fed diets for 8 wk, that had either a low (0.01% wt/wt), normal (0.67%), or high (3%) Ca content. Plasma (Ca) was 32% less and 11% more in rats fed low (LOCA) and high Ca diets (HICA), respectively, than in rats fed a normal Ca diet (CONT). The mean permeability-surface area product (PA) of 45Ca at the blood-nerve barrier was about eightfoldmore » higher than at the blood-brain barrier in the same animals and did not differ significantly between groups (greater than 0.05). Mean PA ratios of 45Ca/36Cl for the blood-nerve and blood-brain barriers in CONT rats, 0.52 {plus minus} 0.04 and 0.40 {plus minus} 0.02, respectively, were not significantly different from corresponding ratios in LOCA and HICA groups, and corresponded to the aqueous limiting diffusion ratio (0.45). The authors results show no evidence for concentration-dependent transport of Ca over a plasma (Ca) range of 0.8-1.4 mmol/liter at the blood-nerve barrier of the rat peripheral nerve, and suggest that Ca and Cl exchange slowly between nerve and blood via paracellular pathways.« less

SPES-2, AP600 intergral system test S01007 2 inch CL to core make-up tank pressure balance line break

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bacchiani, M.; Medich, C.; Rigamonti, M.

1995-09-01

The SPES-2 is a full height, full pressure experimental test facility reproducing the Westinghouse AP600 reactor with a scaling factor of 1/395. The experimental plant, designed and operated by SIET in Piacenza, consists of a full simulation of the AP600 primary core cooling system including all the passive and active safety systems. In 1992, Westinghouse, in cooperation with ENEL (Ente Nazionale per l` Energia Elettrica), ENEA (Enter per le numove Technlogie, l` Energia e l` Ambient), Siet (Societa Informazioni Esperienze Termoidraulich) and ANSALDO developed an experimental program to test the integrated behaviour of the AP600 passive safety systems. The SPES-2more » test matrix, concluded in November 1994, has examined the AP600 passive safety system response for a range of small break LOCAs at different locations on the primary system and on the passive system lines; single steam generator tube ruptures with passive and active safety systems and a main steam line break transient to demonstrate the boration capability of passive safety systems for rapid cooldown. Each of the tests has provided detailed experimental results for verification of the capability of the analysis methods to predict the integrated passive safety system behaviour. Cold and hot shakedown tests have been performed on the facility to check the characteristics of the plant before starting the experimental campaign. The paper first presents a description of the SPES-2 test facility then the main results of S01007 test {open_quotes}2{close_quotes} Cold Leg (CL) to Core Make-up Tank (CMT) pressure balance line break{close_quotes} are reported and compared with predictions performed using RELAP5/mod3/80 obtained by ANSALDO through agreement with U.S.N.R.C. (U.S. Nuclear Regulatory Commission). The SPES-2 nodalization and all the calculations here presented were performed by ANSALDO and sponsored by ENEL as a part of pre-test predictions for SPES-2.« less

Simulation Training in Obstetrics and Gynaecology Residency Programs in Canada.

PubMed

Sanders, Ari; Wilson, R Douglas

2015-11-01

The integration of simulation into residency programs has been slower in obstetrics and gynaecology than in other surgical specialties. The goal of this study was to evaluate the current use of simulation in obstetrics and gynaecology residency programs in Canada. A 19-question survey was developed and distributed to all 16 active and accredited obstetrics and gynaecology residency programs in Canada. The survey was sent to program directors initially, but on occasion was redirected to other faculty members involved in resident education or to senior residents. Survey responses were collected over an 18-month period. Twelve programs responded to the survey (11 complete responses). Eleven programs (92%) reported introducing an obstetrics and gynaecology simulation curriculum into their residency education. All respondents (100%) had access to a simulation centre. Simulation was used to teach various obstetrical and gynaecological skills using different simulation modalities. Barriers to simulation integration were primarily the costs of equipment and space and the need to ensure dedicated time for residents and educators. The majority of programs indicated that it was a priority for them to enhance their simulation curriculum and transition to competency-based resident assessment. Simulation training has increased in obstetrics and gynaecology residency programs. The development of formal simulation curricula for use in obstetrics and gynaecology resident education is in early development. A standardized national simulation curriculum would help facilitate the integration of simulation into obstetrics and gynaecology resident education and aid in the shift to competency-based resident assessment. Obstetrics and gynaecology residency programs need national collaboration (between centres and specialties) to develop a standardized simulation curriculum for use in obstetrics and gynaecology residency programs in Canada.

Study of clad ballooning and rupture behaviour of Indian PHWR fuel pins under transient heating condition in steam environment

NASA Astrophysics Data System (ADS)

Sawarn, Tapan K.; Banerjee, Suparna; Sheelvantra, Smita S.; Singh, J. L.; Bhasin, Vivek

2017-11-01

This paper presents the results of the investigation on the deformation and rupture characteristics of Indian pressurized heavy water reactor (IPHWR) fuel pins under simulated loss of coolant accident (LOCA) condition in steam environment. Transient heating experiments were carried out on single fuel pin internally pressurized with argon gas in the range 3-70 bar. Effect of internal pressure on burst temperature, influence of burst temperature on the circumferential strain and rupture opening area were also studied. Two circumferential strain maxima at the burst temperatures of 740 & ∼979 °C and a minimum at the burst temperature of ∼868 °C were observed. It was found that oxidation had considerable effect on the burst behavior. Test data were used to derive a direct empirical correlation for burst stress exclusively as a function of temperature. The ballooning and rupture behaviours in steam and argon environments have been compared. Experimental data were examined against various correlations using Erbacher equation and author's previous correlation in argon. A second burst correlation has also been developed combining the equation in argon from the previous work of the authors and an exponential factor with oxygen content as a parameter assuming the burst stress to be a function of both temperature and oxygen concentration. The burst temperatures predicted by this empirical correlation are in good agreement with the test data.

Development and Validation of Accident Models for FeCrAl Cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gamble, Kyle Allan Lawrence; Hales, Jason Dean

2016-08-01

The purpose of this milestone report is to present the work completed in regards to material model development for FeCrAl cladding and highlight the results of applying these models to Loss of Coolant Accidents (LOCA) and Station Blackouts (SBO). With the limited experimental data available (essentially only the data used to create the models) true validation is not possible. In the absence of another alternative, qualitative comparisons during postulated accident scenarios between FeCrAl and Zircaloy-4 cladded rods have been completed demonstrating the superior performance of FeCrAl.

Emergency heat removal system for a nuclear reactor

DOEpatents

Dunckel, Thomas L.

1976-01-01

A heat removal system for nuclear reactors serving as a supplement to an Emergency Core Cooling System (ECCS) during a Loss of Coolant Accident (LOCA) comprises a plurality of heat pipes having one end in heat transfer relationship with either the reactor pressure vessel, the core support grid structure or other in-core components and the opposite end located in heat transfer relationship with a heat exchanger having heat transfer fluid therein. The heat exchanger is located external to the pressure vessel whereby excessive core heat is transferred from the above reactor components and dissipated within the heat exchanger fluid.

General Electromagnetic Model for the Analysis of Complex Systems (GEMACS) Computer Code Documentation (Version 3). Volume 3. Part 2.

DTIC Science & Technology

1983-09-01

F.P. PX /AMPZIJ/ REFH /AMPZIJ/ REFV /AI4PZIJ/ * RHOX /AI4PZIJ/ RHOY /At4PZIJ/ RHOZ /AI4PZIJ/ S A-ZJ SA /AMPZIJ/ SALP /AMPZIJ/ 6. CALLING ROUTINE: FLDDRV...US3NG ALGORITHM 72 COMPUTE P- YES .~:*:.~~ USING* *. 1. NAME: PLAINT (GTD) ] 2. PURPOSE: To determine if a ray traveling from a given source loca...determine if a source ray reflection from plate MP occurs. If a ray traveling from the source image location in the reflected ray direction passes through

Westinghouse Small Modular Reactor passive safety system response to postulated events

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, M. C.; Wright, R. F.

2012-07-01

The Westinghouse Small Modular Reactor (SMR) is an 800 MWt (>225 MWe) integral pressurized water reactor. This paper is part of a series of four describing the design and safety features of the Westinghouse SMR. This paper focuses in particular upon the passive safety features and the safety system response of the Westinghouse SMR. The Westinghouse SMR design incorporates many features to minimize the effects of, and in some cases eliminates the possibility of postulated accidents. The small size of the reactor and the low power density limits the potential consequences of an accident relative to a large plant. Themore » integral design eliminates large loop piping, which significantly reduces the flow area of postulated loss of coolant accidents (LOCAs). The Westinghouse SMR containment is a high-pressure, compact design that normally operates at a partial vacuum. This facilitates heat removal from the containment during LOCA events. The containment is submerged in water which also aides the heat removal and provides an additional radionuclide filter. The Westinghouse SMR safety system design is passive, is based largely on the passive safety systems used in the AP1000{sup R} reactor, and provides mitigation of all design basis accidents without the need for AC electrical power for a period of seven days. Frequent faults, such as reactivity insertion events and loss of power events, are protected by first shutting down the nuclear reaction by inserting control rods, then providing cold, borated water through a passive, buoyancy-driven flow. Decay heat removal is provided using a layered approach that includes the passive removal of heat by the steam drum and independent passive heat removal system that transfers heat from the primary system to the environment. Less frequent faults such as loss of coolant accidents are mitigated by passive injection of a large quantity of water that is readily available inside containment. An automatic depressurization system is used to reduce the reactor pressure in a controlled manner to facilitate the passive injection. Long-term decay heat removal is accomplished using the passive heat removal systems augmented by heat transfer through the containment vessel to the environment. The passive injection systems are designed so that the fuel remains covered and effectively cooled throughout the event. Like during the frequent faults, the passive systems provide effective cooling without the need for ac power for seven days following the accident. Connections are available to add additional water to indefinitely cool the plant. The response of the safety systems of the Westinghouse SMR to various initiating faults has been examined. Among them, two accidents; an extended station blackout event, and a LOCA event have been evaluated to demonstrate how the plant will remain safe in the unlikely event that either should occur. (authors)« less

LOADING SIMULATION PROGRAM C

EPA Pesticide Factsheets

LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for simulating hydrology, sediment, and general water quality

Simulation Use in Paramedic Education Research (SUPER): A Descriptive Study

PubMed Central

McKenna, Kim D.; Carhart, Elliot; Bercher, Daniel; Spain, Andrew; Todaro, John; Freel, Joann

2015-01-01

Abstract Objectives. The purpose of this research was to characterize the use of simulation in initial paramedic education programs in order assist stakeholders’ efforts to target educational initiatives and resources. This group sought to provide a snapshot of what simulation resources programs have or have access to and how they are used; faculty perceptions about simulation; whether program characteristics, resources, or faculty training influence simulation use; and if simulation resources are uniform for patients of all ages. Methods. This was a cross-sectional census survey of paramedic programs that were accredited or had a Letter of Review from the Committee on Accreditation of Educational Programs for the EMS Professions at the time of the study. The data were analyzed using descriptive statistics and chi-square analyses. Results. Of the 638 surveys sent, 389 valid responses (61%) were analyzed. Paramedic programs reported they have or have access to a wide range of simulation resources (task trainers [100%], simple manikins [100%], intermediate manikins [99%], advanced/fully programmable manikins [91%], live simulated patients [83%], computer-based [71%], and virtual reality [19%]); however, they do not consistently use them, particularly advanced (71%), live simulated patients (66%), computer-based (games, scenarios) (31%), and virtual reality (4%). Simulation equipment (of any type) reportedly sits idle and unused in (31%) of programs. Lack of training was cited as the most common reason. Personnel support specific to simulation was available in 44% of programs. Programs reported using simulation to replace skills more frequently than to replace field or clinical hours. Simulation goals included assessment, critical thinking, and problem-solving most frequently, and patient and crew safety least often. Programs using advanced manikins report manufacturers as their primary means of training (87%) and that 19% of faculty had no training specific to those manikins. Many (78%) respondents felt they should use more simulation. Conclusions. Paramedic programs have and have access to diverse simulation resources; however, faculty training and other program resources appear to influence their use. PMID:25664774

Simulation Use in Paramedic Education Research (SUPER): A Descriptive Study.

PubMed

McKenna, Kim D; Carhart, Elliot; Bercher, Daniel; Spain, Andrew; Todaro, John; Freel, Joann

2015-01-01

The purpose of this research was to characterize the use of simulation in initial paramedic education programs in order assist stakeholders' efforts to target educational initiatives and resources. This group sought to provide a snapshot of what simulation resources programs have or have access to and how they are used; faculty perceptions about simulation; whether program characteristics, resources, or faculty training influence simulation use; and if simulation resources are uniform for patients of all ages. This was a cross-sectional census survey of paramedic programs that were accredited or had a Letter of Review from the Committee on Accreditation of Educational Programs for the EMS Professions at the time of the study. The data were analyzed using descriptive statistics and chi-square analyses. Of the 638 surveys sent, 389 valid responses (61%) were analyzed. Paramedic programs reported they have or have access to a wide range of simulation resources (task trainers [100%], simple manikins [100%], intermediate manikins [99%], advanced/fully programmable manikins [91%], live simulated patients [83%], computer-based [71%], and virtual reality [19%]); however, they do not consistently use them, particularly advanced (71%), live simulated patients (66%), computer-based (games, scenarios) (31%), and virtual reality (4%). Simulation equipment (of any type) reportedly sits idle and unused in (31%) of programs. Lack of training was cited as the most common reason. Personnel support specific to simulation was available in 44% of programs. Programs reported using simulation to replace skills more frequently than to replace field or clinical hours. Simulation goals included assessment, critical thinking, and problem-solving most frequently, and patient and crew safety least often. Programs using advanced manikins report manufacturers as their primary means of training (87%) and that 19% of faculty had no training specific to those manikins. Many (78%) respondents felt they should use more simulation. Paramedic programs have and have access to diverse simulation resources; however, faculty training and other program resources appear to influence their use.

Simulation in Canadian postgraduate emergency medicine training - a national survey.

PubMed

Russell, Evan; Hall, Andrew Koch; Hagel, Carly; Petrosoniak, Andrew; Dagnone, Jeffrey Damon; Howes, Daniel

2018-01-01

Simulation-based education (SBE) is an important training strategy in emergency medicine (EM) postgraduate programs. This study sought to characterize the use of simulation in FRCPC-EM residency programs across Canada. A national survey was administered to residents and knowledgeable program representatives (PRs) at all Canadian FRCPC-EM programs. Survey question themes included simulation program characteristics, the frequency of resident participation, the location and administration of SBE, institutional barriers, interprofessional involvement, content, assessment strategies, and attitudes about SBE. Resident and PR response rates were 63% (203/321) and 100% (16/16), respectively. Residents reported a median of 20 (range 0-150) hours of annual simulation training, with 52% of residents indicating that the time dedicated to simulation training met their needs. PRs reported the frequency of SBE sessions ranging from weekly to every 6 months, with 15 (94%) programs having an established simulation curriculum. Two (13%) of the programs used simulation for resident assessment, although 15 (94%) of PRs indicated that they would be comfortable with simulation-based assessment. The most common PR-identified barriers to administering simulation were a lack of protected faculty time (75%) and a lack of faculty experience with simulation (56%). Interprofessional involvement in simulation was strongly valued by both residents and PRs. SBE is frequently used by Canadian FRCPC-EM residency programs. However, there exists considerable variability in the structure, frequency, and timing of simulation-based activities. As programs transition to competency-based medical education, national organizations and collaborations should consider the variability in how SBE is administered.

A Simulation Program for Dynamic Infrared (IR) Spectra

ERIC Educational Resources Information Center

Zoerb, Matthew C.; Harris, Charles B.

2013-01-01

A free program for the simulation of dynamic infrared (IR) spectra is presented. The program simulates the spectrum of two exchanging IR peaks based on simple input parameters. Larger systems can be simulated with minor modifications. The program is available as an executable program for PCs or can be run in MATLAB on any operating system. Source…

Payload training methodology study

NASA Technical Reports Server (NTRS)

1990-01-01

The results of the Payload Training Methodology Study (PTMS) are documented. Methods and procedures are defined for the development of payload training programs to be conducted at the Marshall Space Flight Center Payload Training Complex (PCT) for the Space Station Freedom program. The study outlines the overall training program concept as well as the six methodologies associated with the program implementation. The program concept outlines the entire payload training program from initial identification of training requirements to the development of detailed design specifications for simulators and instructional material. The following six methodologies are defined: (1) The Training and Simulation Needs Assessment Methodology; (2) The Simulation Approach Methodology; (3) The Simulation Definition Analysis Methodology; (4) The Simulator Requirements Standardization Methodology; (5) The Simulator Development Verification Methodology; and (6) The Simulator Validation Methodology.

Programming of a flexible computer simulation to visualize pharmacokinetic-pharmacodynamic models.

PubMed

Lötsch, J; Kobal, G; Geisslinger, G

2004-01-01

Teaching pharmacokinetic-pharmacodynamic (PK/PD) models can be made more effective using computer simulations. We propose the programming of educational PK or PK/PD computer simulations as an alternative to the use of pre-built simulation software. This approach has the advantage of adaptability to non-standard or complicated PK or PK/PD models. Simplicity of the programming procedure was achieved by selecting the LabVIEW programming environment. An intuitive user interface to visualize the time courses of drug concentrations or effects can be obtained with pre-built elements. The environment uses a wiring analogy that resembles electrical circuit diagrams rather than abstract programming code. The goal of high interactivity of the simulation was attained by allowing the program to run in continuously repeating loops. This makes the program behave flexibly to the user input. The programming is described with the aid of a 2-compartment PK simulation. Examples of more sophisticated simulation programs are also given where the PK/PD simulation shows drug input, concentrations in plasma, and at effect site and the effects themselves as a function of time. A multi-compartmental model of morphine, including metabolite kinetics and effects is also included. The programs are available for download from the World Wide Web at http:// www. klinik.uni-frankfurt.de/zpharm/klin/ PKPDsimulation/content.html. For pharmacokineticists who only program occasionally, there is the possibility of building the computer simulation, together with the flexible interactive simulation algorithm for clinical pharmacological teaching in the field of PK/PD models.

Simulation Activity in Otolaryngology Residencies.

PubMed

Deutsch, Ellen S; Wiet, Gregory J; Seidman, Michael; Hussey, Heather M; Malekzadeh, Sonya; Fried, Marvin P

2015-08-01

Simulation has become a valuable tool in medical education, and several specialties accept or require simulation as a resource for resident training or assessment as well as for board certification or maintenance of certification. This study investigates current simulation resources and activities in US otolaryngology residency programs and examines interest in advancing simulation training and assessment within the specialty. Web-based survey. US otolaryngology residency training programs. An electronic web-based survey was disseminated to all US otolaryngology program directors to determine their respective institutional and departmental simulation resources, existing simulation activities, and interest in further simulation initiatives. Descriptive results are reported. Responses were received from 43 of 104 (43%) residency programs. Simulation capabilities and resources are available in most respondents' institutions (78.6% report onsite resources; 73.8% report availability of models, manikins, and devices). Most respondents (61%) report limited simulation activity within otolaryngology. Areas of simulation are broad, addressing technical and nontechnical skills related to clinical training (94%). Simulation is infrequently used for research, credentialing, or systems improvement. The majority of respondents (83.8%) expressed interest in participating in multicenter trials of simulation initiatives. Most respondents from otolaryngology residency programs have incorporated some simulation into their curriculum. Interest among program directors to participate in future multicenter trials appears high. Future research efforts in this area should aim to determine optimal simulators and simulation activities for training and assessment as well as how to best incorporate simulation into otolaryngology residency training programs. © American Academy of Otolaryngology—Head and Neck Surgery Foundation 2015.

78 FR 30956 - Cruise Vessel Security and Safety Training Provider Certification

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-23

..., practical demonstration, or simulation program. A detailed instructor manual must be submitted. Submissions... simulation programs to be used. If a simulator or simulation program is to be used, include technical... lessons and, if appropriate, for practical demonstrations or simulation exercises and assessments...

The desirability of education in didactic skills according to medical interns.

PubMed

Kloek, Anne T; Verbakel, Joshua R A; Bernard, Simone E; Evenboer, Januska; Hendriks, Eef J; Stam, Hanneke

2012-12-01

Since all doctors at some point in their career will be faced with their role as a teacher, it appears desirable that future doctors are educated in didactic skills. At present, however, there are no formal opportunities for developing didactic skills at the majority of Dutch medical faculties. The main question of this study is: How do medical interns perceive the quality and quantity of their education in didactic skills? The Dutch Association for Medical Interns (LOCA) ran a national survey among 1,008 medical interns that measured the interns' self-assessed needs for training in didactic skills during medical school. Almost 80 % of the respondents argue that the mastery of didactic skills composes an essential competency for doctors, with the skill of providing adequate feedback considered to be the most important didactic quality for doctors. Of the respondents, 41 % wish to be educated in didactic skills, both during their medical undergraduate degree and during their subsequent training to become a resident. Teaching while being observed and receiving feedback in this setting is regarded as a particularly valuable didactic method by 74 % of the medical interns. Of the respondents, 82 % would invest time to follow training for the development of didactic skills if it was offered. Medical interns stress the importance of doctors' didactic skills during their clinical internships. Compared with current levels, most interns desire increased attention to the formal development of didactic skills during medical school. Considering the importance of didactic skills and the need for more extensive training, the LOCA advises medical faculties to include more formal didactic training in the medical curriculum.

Geochemical and Hydrologic Controls of Copper-Rich Surface Waters in the Yerba Loca-Mapocho System

NASA Astrophysics Data System (ADS)

Pasten, P.; Montecinos, M.; Coquery, M.; Pizarro, G. E.; Abarca, M. I.; Arce, G. J.

2015-12-01

Andean watersheds in Northern and Central Chile are naturally enriched with metals, many of them associated to sulfide mineralizations related to copper mining districts. The natural and anthropogenic influx of toxic metals into drinking water sources pose a sustainability challenge for cities that need to provide safe water with the smallest footprint. This work presents our study of the transformations of copper in the Yerba Loca-Mapocho system. Our sampling campaign started from the headwaters at La Paloma Glacier and continues to the inlet of the San Enrique drinking water treatment plant, a system feeding municipalities in the Eastern area of Santiago, Chile. Depending on the season, total copper concentrations go as high as 22 mg/L for the upper sections, which become diluted to <5 mg/L downstream. pH ranged from 3 to 5.6 while suspended solids ranged from <10 to 100 mg/L. We used Geochemist Workbench to assess copper speciation and to evaluate the thermodynamic controls for the formation and dissolution of solid phases. A sediment trap was used to concentrate suspended particulate matter, which was analyzed with ICP-MS, TXRF (total reflection X ray fluorescence) and XRD (X-ray diffraction). Major elements detected in the precipitates were Al (200 g/kg), S (60 g/kg), and Cu (6 g/kg). Likely solid phases include hydrous amorphous phases of aluminum hydroxides and sulfates, and copper hydroxides/carbonates. Efforts are undergoing to find the optimal mixing ratios between the acidic stream and more alkaline streams to maximize attenuation of dissolved copper. The results of this research could be used for enhancing in-stream natural attenuation of copper and reducing treatment needs at the drinking water facility. Acknowledgements to Fondecyt 1130936 and Conicyt Fondap 15110020

A National Survey on the Use of Immersive Simulation for Interprofessional Education in Physical Therapist Education Programs.

PubMed

Stockert, Brad; Ohtake, Patricia J

2017-10-01

There is growing recognition that collaborative practice among healthcare professionals is associated with improved patient outcomes and enhanced team functioning, but development of collaborative practitioners requires interprofessional education (IPE). Immersive simulation, a clinically relevant experience that deeply engages the learner in realistic clinical environments, is used increasingly for IPE. The purpose of this study was to assess the use of immersive simulation as a strategy for IPE in physical therapist (PT) education programs. During fall 2014 and spring 2015, we contacted all 214 Commission on Accreditation in Physical Therapy Education accredited PT education programs in the United States and invited a faculty member to participate in our online survey. One hundred fourteen PT programs responded (53% response rate). Eighty responding programs (70%) identified themselves as users of immersive simulation, and 45 programs (39%) used simulation for IPE. Of these 45 programs, more than 90% included Interprofessional Education Collaborative competency learning objectives of roles/responsibilities, interprofessional communication, and teams/teamwork and 51% reported learning objectives for values/ethics for interprofessional practice. Interprofessional simulations with PT students commonly included nursing (91%). In programs using immersive simulation for IPE, 91% included debriefing and 51% included debriefing by interprofessional teams. Eighty accredited PT programs (70%) that responded to the survey use immersive simulation, and 45 programs (39%) use simulation for IPE. Most programs conduct simulations consistent with recognized best practice, including debriefing and Interprofessional Education Collaborative competency learning objectives for promoting interprofessional collaborative practice. We anticipate an increase in the use of immersive simulation for IPE as an educational strategy to comply with the revised Commission on Accreditation in Physical Therapy Education accreditation standards related to interprofessional collaborative practice that will become effective on January 1, 2018.

Simulation of CIFF (Centralized IFF) remote control displays

NASA Astrophysics Data System (ADS)

Tucker, D. L.; Leibowitz, L. M.

1986-06-01

This report presents the software simulation of the Remote-Control-Display (RCS) proposed to be used in the Centralized IFF (CIFF) system. A description of the simulation programs along with simulated menu formats are presented. A sample listing of the simulation programs and a brief description of the program operation are also included.

Status of Microsurgical Simulation Training in Plastic Surgery: A Survey of United States Program Directors.

PubMed

Al-Bustani, Saif; Halvorson, Eric G

2016-06-01

Various simulation models for microsurgery have been developed to overcome the limitations of Halstedian training on real patients. We wanted to assess the status of microsurgery simulation in plastic surgery residency programs in the United States. Data were analyzed from responses to a survey sent to all plastic surgery program directors in the United States, asking for type of simulation, quality of facilities, utilization by trainees, evaluation of trainee sessions, and perception of the relevance of simulation. The survey response rate was 50%. Of all programs, 69% provide microsurgical simulation and 75% of these have a laboratory with microscope and 52% provide live animal models. Half share facilities with other departments. The quality of facilities is rated as good or great in 89%. Trainee utilization is once every 3 to 6 months in 82% of programs. Only in 11% is utilization monthly. Formal evaluation of simulation sessions is provided by 41% of programs. All program directors agree simulation is relevant to competence in microsurgery, 60% agree simulation should be mandatory, and 43% require trainees to complete a formal microsurgery course prior to live surgery. There seems to be consensus that microsurgical simulation improves competence, and the majority of program directors agree it should be mandatory. Developing and implementing standardized simulation modules and assessment tools for trainees across the nation as part of a comprehensive competency-based training program for microsurgery is an important patient safety initiative that should be considered. Organizing with other departments to share facilities may improve their quality and hence utilization.

PANDA asymmetric-configuration passive decay heat removal test results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, O.; Dreier, J.; Aubert, C.

1997-12-01

PANDA is a large-scale, low-pressure test facility for investigating passive decay heat removal systems for the next generation of LWRs. In the first series of experiments, PANDA was used to examine the long-term LOCA response of the Passive Containment Cooling System (PCCS) for the General Electric (GE) Simplified Boiling Water Reactor (SBWR). The test objectives include concept demonstration and extension of the database available for qualification of containment codes. Also included is the study of the effects of nonuniform distributions of steam and noncondensable gases in the Dry-well (DW) and in the Suppression Chamber (SC). 3 refs., 9 figs.

Program For Simulation Of Trajectories And Events

NASA Technical Reports Server (NTRS)

Gottlieb, Robert G.

1992-01-01

Universal Simulation Executive (USE) program accelerates and eases generation of application programs for numerical simulation of continuous trajectories interrupted by or containing discrete events. Developed for simulation of multiple spacecraft trajectories with events as one spacecraft crossing the equator, two spacecraft meeting or parting, or firing rocket engine. USE also simulates operation of chemical batch processing factory. Written in Ada.

Program For Parallel Discrete-Event Simulation

NASA Technical Reports Server (NTRS)

Beckman, Brian C.; Blume, Leo R.; Geiselman, John S.; Presley, Matthew T.; Wedel, John J., Jr.; Bellenot, Steven F.; Diloreto, Michael; Hontalas, Philip J.; Reiher, Peter L.; Weiland, Frederick P.

1991-01-01

User does not have to add any special logic to aid in synchronization. Time Warp Operating System (TWOS) computer program is special-purpose operating system designed to support parallel discrete-event simulation. Complete implementation of Time Warp mechanism. Supports only simulations and other computations designed for virtual time. Time Warp Simulator (TWSIM) subdirectory contains sequential simulation engine interface-compatible with TWOS. TWOS and TWSIM written in, and support simulations in, C programming language.

A simulation model for wind energy storage systems. Volume 3: Program descriptions

NASA Technical Reports Server (NTRS)

Warren, A. W.; Edsinger, R. W.; Burroughs, J. D.

1977-01-01

Program descriptions, flow charts, and program listings for the SIMWEST model generation program, the simulation program, the file maintenance program, and the printer plotter program are given. For Vol 2, see .

Human operator identification model and related computer programs

NASA Technical Reports Server (NTRS)

Kessler, K. M.; Mohr, J. N.

1978-01-01

Four computer programs which provide computational assistance in the analysis of man/machine systems are reported. The programs are: (1) Modified Transfer Function Program (TF); (2) Time Varying Response Program (TVSR); (3) Optimal Simulation Program (TVOPT); and (4) Linear Identification Program (SCIDNT). The TV program converts the time domain state variable system representative to frequency domain transfer function system representation. The TVSR program computes time histories of the input/output responses of the human operator model. The TVOPT program is an optimal simulation program and is similar to TVSR in that it produces time histories of system states associated with an operator in the loop system. The differences between the two programs are presented. The SCIDNT program is an open loop identification code which operates on the simulated data from TVOPT (or TVSR) or real operator data from motion simulators.

Survey of outcomes in a faculty development program on simulation pedagogy.

PubMed

Roh, Young Sook; Kim, Mi Kang; Tangkawanich, Thitiarpha

2016-06-01

Although many nursing programs use simulation as a teaching-learning modality, there are few systematic approaches to help nursing educators learn this pedagogy. This study evaluates the effects of a simulation pedagogy nursing faculty development program on participants' learning perceptions using a retrospective pre-course and post-course design. Sixteen Thai participants completed a two-day nursing faculty development program on simulation pedagogy. Thirteen questionnaires were used in the final analysis. The participants' self-perceived learning about simulation teaching showed significant post-course improvement. On a five-point Likert scale, the composite mean attitude, subjective norm, and perceived behavioral control scores, as well as intention to use a simulator, showed a significant post-course increase. A faculty development program on simulation pedagogy induced favorable learning and attitudes. Further studies must test how faculty performance affects the cognitive, emotional, and social dimensions of learning in a simulation-based learning domain. © 2015 Wiley Publishing Asia Pty Ltd.

Summary on the depressurization from supercritical pressure conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, M.; Chen, Y.; Ammirable, L.

When a fluid discharges from a high pressure and temperature system, a 'choking' or critical condition occurs, and the flow rate becomes independent of the downstream pressure. During a postulated loss of coolant accident (LOCA) of a water reactor the break flow will be subject to this condition. An accurate estimation of the critical flow rate is important for the evaluation of the reactor safety, because this flow rate controls the loss of coolant inventory and energy from the system, and thus has a significant effect on the accident consequences[1]. In the design of safety systems for a super criticalmore » water reactor (SCWR), postulated LOCA transients are particularly important due to the lower coolant inventory compared to a typical PWR for the same power output. This lower coolant inventory would result in a faster transient response of the SCWR, and hence accurate prediction of the critical discharge is mandatory. Under potential two-phase conditions critical flow is dominated by the vapor content or quality of the vapor, which is closely related with the onset of vaporization and the interfacial interaction between phases [2]. This presents a major challenge for the estimation of the flow rate due to the lack of the knowledge of those processes, especially under the conditions of interest for the SCWR. According to the limited data of supercritical fluids, the critical flows at conditions above the pseudo-critical point seem to be fairly stable and consistent with the subcritical homogeneous equilibrium model (HEM) model predictions, while having a lower flow rate than those in the two-phase region. Thus the major difficulty in the prediction of the depressurization flow rates remains in the region where two phases co-exist at the top of the vapor dome. In this region, the flow rate is strongly affected by the nozzle geometry and tends to be unstable. Various models for this region have been developed with different assumptions, e.g. the HEM and Moody model [3], and the Henry-Fauske non-equilibrium model [4], and are currently used in subcritical pressure reactor safety design[5]. It appears that some of these models could be reasonably extended to above the thermodynamic pseudo-critical point. The more stable and lower discharge flow rates observed in conditions above the pseudo-critical point suggests that even though SCWR's have a smaller coolant inventory, the safety implications of a LOCA and the subsequent depressurization may not be as severe as expected, this however needs to be confirmed by a rigorous evaluation of the particular event and further evaluation of the critical flow rate. This paper will summarize activities on critical flow models, experimental data and numerical modeling during blowdown from supercritical pressure conditions under the International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) on 'Heat Transfer Behaviour and Thermo-hydraulics Code testing for SCWRs'. (authors)« less

SICONID: a FORTRAN-77 program for conditional simulation in one dimension

NASA Astrophysics Data System (ADS)

Pardo-Igúzquiza, E.; Chica-Olmo, M.; Delgado-García, J.

1992-07-01

The SICONID program, written in FORTRAN 77 for the conditional simulation of geological variables in one dimension, is presented. The program permits all the necessary steps to obtain a simulated series of the experimental data to be carried out. These states are: acquisition of the experimental values, modelization of the anamorphosis function, variogram of the normal scores, conditional simulation, and restoration of the experimental histogram. A practical case of simulation of the evolution of the groundwater level in a survey to show the operation of the program is given.

Implementing a high-fidelity simulation program in a community college setting.

PubMed

Tuoriniemi, Pamela; Schott-Baer, Darlene

2008-01-01

Despite their relatively high cost, there is heightened interest by faculty in undergraduate nursing programs to implement high-fidelity simulation (HFS) programs. High-fidelity simulators are appealing because they allow students to experience high-risk, low-volume patient problems in a realistic setting. The decision to purchase a simulator is the first step in the process of implementing and maintaining an HFS lab. Knowledge, technical skill, commitment, and considerable time are needed to develop a successful program. The process, as experienced by one community college nursing program, is described.

Simulating smokers' acceptance of modifications in a cessation program.

PubMed Central

Spoth, R

1992-01-01

Recent research has underscored the importance of assessing barriers to smokers' acceptance of cessation programs. This paper illustrates the use of computer simulations to gauge smokers' response to program modifications which may produce barriers to participation. It also highlights methodological issues encountered in conducting this work. Computer simulations were based on conjoint analysis, a consumer research method which enables measurement of smokers' relative preference for various modifications of cessation programs. Results from two studies are presented in this paper. The primary study used a randomly selected sample of 218 adult smokers who participated in a computer-assisted phone interview. Initially, the study assessed smokers' relative utility rating of 30 features of cessation programs. Utility data were used in computer-simulated comparisons of a low-cost, self-help oriented program under development and five other existing programs. A baseline version of the program under development and two modifications (for example, use of a support group with a higher level of cost) were simulated. Both the baseline version and modifications received a favorable response vis-à-vis comparison programs. Modifications requiring higher program costs were, however, associated with moderately reduced levels of favorable consumer response. The second study used a sample of 70 smokers who responded to an expanded set of smoking cessation program features focusing on program packaging. This secondary study incorporate in-person, computer-assisted interviews at a shopping mall, with smokers viewing an artist's mock-up of various program options on display. A similar pattern of responses to simulated program modifications emerged, with monetary cost apparently playing a key role. The significance of conjoint-based computer simulation as a tool in program development or dissemination, salient methodological issues, and implications for further research are discussed. PMID:1738813

Simulating smokers' acceptance of modifications in a cessation program.

PubMed

Spoth, R

1992-01-01

Recent research has underscored the importance of assessing barriers to smokers' acceptance of cessation programs. This paper illustrates the use of computer simulations to gauge smokers' response to program modifications which may produce barriers to participation. It also highlights methodological issues encountered in conducting this work. Computer simulations were based on conjoint analysis, a consumer research method which enables measurement of smokers' relative preference for various modifications of cessation programs. Results from two studies are presented in this paper. The primary study used a randomly selected sample of 218 adult smokers who participated in a computer-assisted phone interview. Initially, the study assessed smokers' relative utility rating of 30 features of cessation programs. Utility data were used in computer-simulated comparisons of a low-cost, self-help oriented program under development and five other existing programs. A baseline version of the program under development and two modifications (for example, use of a support group with a higher level of cost) were simulated. Both the baseline version and modifications received a favorable response vis-à-vis comparison programs. Modifications requiring higher program costs were, however, associated with moderately reduced levels of favorable consumer response. The second study used a sample of 70 smokers who responded to an expanded set of smoking cessation program features focusing on program packaging. This secondary study incorporate in-person, computer-assisted interviews at a shopping mall, with smokers viewing an artist's mock-up of various program options on display. A similar pattern of responses to simulated program modifications emerged, with monetary cost apparently playing a key role. The significance of conjoint-based computer simulation as a tool in program development or dissemination, salient methodological issues, and implications for further research are discussed.

Mechanism-based modeling of solute strengthening: Application to thermal creep in Zr alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wen, Wei; Capolungo, Laurent; Tome, Carlos N.

In this paper, a crystallographic thermal creep model is proposed for Zr alloys that accounts for the hardening contribution of solutes via their time-dependent pinning effect on dislocations. The core-diffusion model proposed by Soare and Curtin (2008a) is coupled with a recently proposed constitutive modeling framework (Wang et al., 2017, 2016) accounting for the heterogeneous distribution of internal stresses within grains. The Coble creep mechanism is also included. This model is, in turn, embedded in the effective medium crystallographic VPSC framework and used to predict creep strain evolution of polycrystals under different temperature and stress conditions. The simulation results reproducemore » the experimental creep data for Zircaloy-4 and the transition between the low (n~1), intermediate (n~4) and high (n~9) power law creep regimes. This is achieved through the dependence on local aging time of the solute-dislocation binding energy. The anomalies in strain rate sensitivity (SRS) are discussed in terms of core-diffusion effects on dislocation junction strength. The mechanism-based model captures the primary and secondary creep regimes results reported by Kombaiah and Murty (2015a, 2015b) for a comprehensive set of testing conditions covering the 500–600 °C interval, stresses spanning 14–156 MPa, and steady state creep rates varying between 1.5·10 -9s -1 to 2·10 -3s -1. There are two major advantages to this model with respect to more empirical ones used as constitutive laws for describing thermal creep of cladding: 1) specific dependences on the nature of solutes and their concentrations are explicitly accounted for; 2) accident conditions in reactors, such as RIA and LOCA, usually take place in short times, and deformation takes place in the primary, not the steady-state creep stage. Finally, as a consequence, a model that accounts for the evolution with time of microstructure is more reliable for this kind of simulation.« less

Mechanism-based modeling of solute strengthening: Application to thermal creep in Zr alloy

DOE PAGES

Wen, Wei; Capolungo, Laurent; Tome, Carlos N.

2018-03-11

In this paper, a crystallographic thermal creep model is proposed for Zr alloys that accounts for the hardening contribution of solutes via their time-dependent pinning effect on dislocations. The core-diffusion model proposed by Soare and Curtin (2008a) is coupled with a recently proposed constitutive modeling framework (Wang et al., 2017, 2016) accounting for the heterogeneous distribution of internal stresses within grains. The Coble creep mechanism is also included. This model is, in turn, embedded in the effective medium crystallographic VPSC framework and used to predict creep strain evolution of polycrystals under different temperature and stress conditions. The simulation results reproducemore » the experimental creep data for Zircaloy-4 and the transition between the low (n~1), intermediate (n~4) and high (n~9) power law creep regimes. This is achieved through the dependence on local aging time of the solute-dislocation binding energy. The anomalies in strain rate sensitivity (SRS) are discussed in terms of core-diffusion effects on dislocation junction strength. The mechanism-based model captures the primary and secondary creep regimes results reported by Kombaiah and Murty (2015a, 2015b) for a comprehensive set of testing conditions covering the 500–600 °C interval, stresses spanning 14–156 MPa, and steady state creep rates varying between 1.5·10 -9s -1 to 2·10 -3s -1. There are two major advantages to this model with respect to more empirical ones used as constitutive laws for describing thermal creep of cladding: 1) specific dependences on the nature of solutes and their concentrations are explicitly accounted for; 2) accident conditions in reactors, such as RIA and LOCA, usually take place in short times, and deformation takes place in the primary, not the steady-state creep stage. Finally, as a consequence, a model that accounts for the evolution with time of microstructure is more reliable for this kind of simulation.« less

A defense in depth approach for nuclear power plant accident management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chih-Yao Hsieh; Hwai-Pwu Chou

2015-07-01

An initiating event may lead to a severe accident if the plant safety functions have been challenged or operators do not follow the appropriate accident management procedures. Beyond design basis accidents are those corresponding to events of very low occurrence probability but such an accident may lead to significant consequences. The defense in depth approach is important to assure nuclear safety even in a severe accident. Plant Damage States (PDS) can be defined by the combination of the possible values for each of the PDS parameters which are showed on the nuclear power plant simulator. PDS is used to identifymore » what the initiating event is, and can also give the information of safety system's status whether they are bypassed, inoperable or not. Initiating event and safety system's status are used in the construction of Containment Event Tree (CET) to determine containment failure modes by using probabilistic risk assessment (PRA) technique. Different initiating events will correspond to different CETs. With these CETs, the core melt frequency of an initiating event can be found. The use of Plant Damage States (PDS) is a symptom-oriented approach. On the other hand, the use of Containment Event Tree (CET) is an event-oriented approach. In this study, the Taiwan's fourth nuclear power plants, the Lungmen nuclear power station (LNPS), which is an advanced boiling water reactor (ABWR) with fully digitized instrumentation and control (I and C) system is chosen as the target plant. The LNPS full scope engineering simulator is used to generate the testing data for method development. The following common initiating events are considered in this study: loss of coolant accidents (LOCA), total loss of feedwater (TLOFW), loss of offsite power (LOOP), station blackout (SBO). Studies have indicated that the combination of the symptom-oriented approach and the event-oriented approach can be helpful to find mitigation strategies and is useful for the accident management. (authors)« less

A real-time digital computer program for the simulation of a single rotor helicopter

NASA Technical Reports Server (NTRS)

Houck, J. A.; Gibson, L. H.; Steinmetz, G. G.

1974-01-01

A computer program was developed for the study of a single-rotor helicopter on the Langley Research Center real-time digital simulation system. Descriptions of helicopter equations and data, program subroutines (including flow charts and listings), real-time simulation system routines, and program operation are included. Program usage is illustrated by standard check cases and a representative flight case.

GROSS- GAMMA RAY OBSERVATORY ATTITUDE DYNAMICS SIMULATOR

NASA Technical Reports Server (NTRS)

Garrick, J.

1994-01-01

The Gamma Ray Observatory (GRO) spacecraft will constitute a major advance in gamma ray astronomy by offering the first opportunity for comprehensive observations in the range of 0.1 to 30,000 megaelectronvolts (MeV). The Gamma Ray Observatory Attitude Dynamics Simulator, GROSS, is designed to simulate this mission. The GRO Dynamics Simulator consists of three separate programs: the Standalone Profile Program; the Simulator Program, which contains the Simulation Control Input/Output (SCIO) Subsystem, the Truth Model (TM) Subsystem, and the Onboard Computer (OBC) Subsystem; and the Postprocessor Program. The Standalone Profile Program models the environment of the spacecraft and generates a profile data set for use by the simulator. This data set contains items such as individual external torques; GRO spacecraft, Tracking and Data Relay Satellite (TDRS), and solar and lunar ephemerides; and star data. The Standalone Profile Program is run before a simulation. The SCIO subsystem is the executive driver for the simulator. It accepts user input, initializes parameters, controls simulation, and generates output data files and simulation status display. The TM subsystem models the spacecraft dynamics, sensors, and actuators. It accepts ephemerides, star data, and environmental torques from the Standalone Profile Program. With these and actuator commands from the OBC subsystem, the TM subsystem propagates the current state of the spacecraft and generates sensor data for use by the OBC and SCIO subsystems. The OBC subsystem uses sensor data from the TM subsystem, a Kalman filter (for attitude determination), and control laws to compute actuator commands to the TM subsystem. The OBC subsystem also provides output data to the SCIO subsystem for output to the analysts. The Postprocessor Program is run after simulation is completed. It generates printer and CRT plots and tabular reports of the simulated data at the direction of the user. GROSS is written in FORTRAN 77 and ASSEMBLER and has been implemented on a VAX 11/780 under VMS 4.5. It has a virtual memory requirement of 255k. GROSS was developed in 1986.

G and C boost and abort study summary, exhibit B

NASA Technical Reports Server (NTRS)

Backman, H. D.

1972-01-01

A six degree of freedom simulation of rigid vehicles was developed to study space shuttle vehicle boost-abort guidance and control techniques. The simulation was described in detail as an all digital program and as a hybrid program. Only the digital simulation was implemented. The equations verified in the digital simulation were adapted for use in the hybrid simulation. Study results were obtained from four abort cases using the digital program.

Generalized environmental control and life support system computer program (G189A) configuration control, phase 2

NASA Technical Reports Server (NTRS)

Mcenulty, R. E.

1977-01-01

The G189A simulation of the Shuttle Orbiter ECLSS was upgraded. All simulation library versions and simulation models were converted from the EXEC2 to the EXEC8 computer system and a new program, G189PL, was added to the combination master program library. The program permits the post-plotting of up to 100 frames of plot data over any time interval of a G189 simulation run. The overlay structure of the G189A simulations were restructured for the purpose of conserving computer core requirements and minimizing run time requirements.

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. (a) Each airplane simulator and other training device that is used in a training course permitted under § 121.409...

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. (a) Each airplane simulator and other training device that is used in a training course permitted under § 121.409...

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. (a) Each airplane simulator and other training device that is used in a training course permitted under § 121.409...

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. Link to an amendment published at 78 FR 67836, Nov. 12, 2013. (a) Each airplane simulator and other training device...

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. (a) Each airplane simulator and other training device that is used in a training course permitted under § 121.409...

Simulator: A Pilot Interactive Simulation Program for Use in Teaching Public Relations.

ERIC Educational Resources Information Center

Pavlik, John V.

An interactive simulation program was developed for use in teaching students how to handle public relations problems. The program user is placed in the role of assistant newsletter editor, facing a series of decision-making situations. Each choice the user makes affects the subsequent reality created by the program, which is designed to provide…

Development of a multilayer interference simulation program for MSS systems

NASA Technical Reports Server (NTRS)

Izadian, Jamal S.

1993-01-01

This paper discusses the development of a multilayer interference analysis and simulation program which is used to evaluate interference between non-geostationary and geostationary satellites. In addition to evaluating interference, this program can be used in the development of sharing criteria and coordination among various Mobile Satellite Services (MSS) systems. A C++/Windows implementation of this program, called Globalstar Interference Simulation Program (GISP), has been developed.

Automatic programming of simulation models

NASA Technical Reports Server (NTRS)

Schroer, Bernard J.; Tseng, Fan T.; Zhang, Shou X.; Dwan, Wen S.

1988-01-01

The objective of automatic programming is to improve the overall environment for describing the program. This improved environment is realized by a reduction in the amount of detail that the programmer needs to know and is exposed to. Furthermore, this improved environment is achieved by a specification language that is more natural to the user's problem domain and to the user's way of thinking and looking at the problem. The goal of this research is to apply the concepts of automatic programming (AP) to modeling discrete event simulation system. Specific emphasis is on the design and development of simulation tools to assist the modeler define or construct a model of the system and to then automatically write the corresponding simulation code in the target simulation language, GPSS/PC. A related goal is to evaluate the feasibility of various languages for constructing automatic programming simulation tools.

Steady-state simulation program for attitude control propulsion systems

NASA Technical Reports Server (NTRS)

Heinmiller, P. J.

1973-01-01

The formulation and the engineering equations employed in the steady state attitude control propulsion system simulation program are presented. The objective of this program is to aid in the preliminary design and development of propulsion systems used for spacecraft attitude control. The program simulates the integrated operation of the many interdependent components typically comprising an attitude control propulsion system. Flexibility, generality, ease of operation, and speed consistent with adequate accuracy were overriding considerations during the development of this program. Simulation modules were developed representing the various types of fluid components typically encountered in an attitude control propulsion system. These modules are basically self-contained and may be arranged by the program user into desired configuration through the program input data.

Passive containment cooling system with drywell pressure regulation for boiling water reactor

DOEpatents

Hill, Paul R.

1994-01-01

A boiling water reactor having a regulating valve for placing the wetwell in flow communication with an intake duct of the passive containment cooling system. This subsystem can be adjusted to maintain the drywell pressure at (or slightly below or above) wetwell pressure after the initial reactor blowdown transient is over. This addition to the PCCS design has the benefit of eliminating or minimizing steam leakage from the drywell to the wetwell in the longer-term post-LOCA time period and also minimizes the temperature difference between drywell and wetwell. This in turn reduces the rate of long-term pressure buildup of the containment, thereby extending the time to reach the design pressure limit.

Computerized Clinical Simulations.

ERIC Educational Resources Information Center

Reinecker, Lynn

1985-01-01

Describes technique involved in designing a clinical simulation problem for the allied health field of respiratory therapy; discusses the structure, content, and scoring categories of the simulation; and provides a sample program which illustrates a programming technique in BASIC, including a program listing and a sample flowchart. (MBR)

Comparing the cost-effectiveness of simulation modalities: a case study of peripheral intravenous catheterization training.

PubMed

Isaranuwatchai, Wanrudee; Brydges, Ryan; Carnahan, Heather; Backstein, David; Dubrowski, Adam

2014-05-01

While the ultimate goal of simulation training is to enhance learning, cost-effectiveness is a critical factor. Research that compares simulation training in terms of educational- and cost-effectiveness will lead to better-informed curricular decisions. Using previously published data we conducted a cost-effectiveness analysis of three simulation-based programs. Medical students (n = 15 per group) practiced in one of three 2-h intravenous catheterization skills training programs: low-fidelity (virtual reality), high-fidelity (mannequin), or progressive (consisting of virtual reality, task trainer, and mannequin simulator). One week later, all performed a transfer test on a hybrid simulation (standardized patient with a task trainer). We used a net benefit regression model to identify the most cost-effective training program via paired comparisons. We also created a cost-effectiveness acceptability curve to visually represent the probability that one program is more cost-effective when compared to its comparator at various 'willingness-to-pay' values. We conducted separate analyses for implementation and total costs. The results showed that the progressive program had the highest total cost (p < 0.001) whereas the high-fidelity program had the highest implementation cost (p < 0.001). While the most cost-effective program depended on the decision makers' willingness-to-pay value, the progressive training program was generally most educationally- and cost-effective. Our analyses suggest that a progressive program that strategically combines simulation modalities provides a cost-effective solution. More generally, we have introduced how a cost-effectiveness analysis may be applied to simulation training; a method that medical educators may use to investment decisions (e.g., purchasing cost-effective and educationally sound simulators).

The Tuscan Mobile Simulation Program: a description of a program for the delivery of in situ simulation training.

PubMed

Ullman, Edward; Kennedy, Maura; Di Delupis, Francesco Dojmi; Pisanelli, Paolo; Burbui, Andrea Giuliattini; Cussen, Meaghan; Galli, Laura; Pini, Riccardo; Gensini, Gian Franco

2016-09-01

Simulation has become a critical aspect of medical education. It allows health care providers the opportunity to focus on safety and high-risk situations in a protected environment. Recently, in situ simulation, which is performed in the actual clinical setting, has been used to recreate a more realistic work environment. This form of simulation allows for better team evaluation as the workers are in their traditional roles, and can reveal latent safety errors that often are not seen in typical simulation scenarios. We discuss the creation and implementation of a mobile in situ simulation program in emergency departments of three hospitals in Tuscany, Italy, including equipment, staffing, and start-up costs for this program. We also describe latent safety threats identified in the pilot in situ simulations. This novel approach has the potential to both reduce the costs of simulation compared to traditional simulation centers, and to expand medical simulation experiences to providers and healthcare organizations that do not have access to a large simulation center.

Pre- and postprocessing for reservoir simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rogers, W.L.; Ingalls, L.J.; Prasad, S.J.

1991-05-01

This paper describes the functionality and underlying programing paradigms of Shell's simulator-related reservoir-engineering graphics system. THis system includes the simulation postprocessing programs Reservoir Display System (RDS) and Fast Reservoir Engineering Displays (FRED), a hypertext-like on-line documentation system (DOC), and a simulator input preprocessor (SIMPLSIM). RDS creates displays of reservoir simulation results. These displays represent the areal or cross-section distribution of computer reservoir parameters, such as pressure, phase saturation, or temperature. Generation of these images at real-time animation rates is discussed. FRED facilitates the creation of plot files from reservoir simulation output. The use of dynamic memory allocation, asynchronous I/O, amore » table-driven screen manager, and mixed-language (FORTRAN and C) programming are detailed. DOC is used to create and access on-line documentation for the pre-and post-processing programs and the reservoir simulators. DOC can be run by itself or can be accessed from within any other graphics or nongraphics application program. DOC includes a text editor, which is that basis for a reservoir simulation tutorial and greatly simplifies the preparation of simulator input. The use of sharable images, graphics, and the documentation file network are described. Finally, SIMPLSIM is a suite of program that uses interactive graphics in the preparation of reservoir description data for input into reservoir simulators. The SIMPLSIM user-interface manager (UIM) and its graphic interface for reservoir description are discussed.« less

Software for Secondary-School Learning About Robotics

NASA Technical Reports Server (NTRS)

Shelton, Robert O.; Smith, Stephanie L.; Truong, Dat; Hodgson, Terry R.

2005-01-01

The ROVer Ranch is an interactive computer program designed to help secondary-school students learn about space-program robotics and related basic scientific concepts by involving the students in simplified design and programming tasks that exercise skills in mathematics and science. The tasks involve building simulated robots and then observing how they behave. The program furnishes (1) programming tools that a student can use to assemble and program a simulated robot and (2) a virtual three-dimensional mission simulator for testing the robot. First, the ROVer Ranch presents fundamental information about robotics, mission goals, and facts about the mission environment. On the basis of this information, and using the aforementioned tools, the student assembles a robot by selecting parts from such subsystems as propulsion, navigation, and scientific tools, the student builds a simulated robot to accomplish its mission. Once the robot is built, it is programmed and then placed in a three-dimensional simulated environment. Success or failure in the simulation depends on the planning and design of the robot. Data and results of the mission are available in a summary log once the mission is concluded.

Effects of a System Thinking-Based Simulation Program for Congestive Heart Failure.

PubMed

Kim, Hyeon-Young; Yun, Eun Kyoung

2018-03-01

This study evaluated a system thinking-based simulation program for the care of patients with congestive heart failure. Participants were 67 undergraduate nursing students from a nursing college in Seoul, South Korea. The experimental group was given a 4-hour system-thinking program and a 2-hour simulation program, whereas the control group had a 4-hour case study and a 2-hour simulation program. There were significant improvements in critical thinking in both groups, but no significant group differences between educational methods (F = 3.26, P = .076). Problem-solving ability in the experimental group was significantly higher than in the control group (F = 5.04, P = .028). Clinical competency skills in the experimental group were higher than in the control group (t = 2.12, P = .038). A system thinking-based simulation program is a more effective learning method in terms of problem-solving ability and clinical competency skills compared to the existing simulation program. Further research using a longitudinal study is needed to test the long-term effect of the intervention and apply it to the nursing curriculum.

Advanced Simulation & Computing FY15 Implementation Plan Volume 2, Rev. 0.5

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCoy, Michel; Archer, Bill; Matzen, M. Keith

2014-09-16

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the surety and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities andmore » computational resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balance of resource, including technical staff, hardware, simulation software, and computer science solutions. As the program approaches the end of its second decade, ASC is intently focused on increasing predictive capabilities in a three-dimensional (3D) simulation environment while maintaining support to the SSP. The program continues to improve its unique tools for solving progressively more difficult stockpile problems (sufficient resolution, dimensionality, and scientific details), quantify critical margins and uncertainties, and resolve increasingly difficult analyses needed for the SSP. Where possible, the program also enables the use of high-performance simulation and computing tools to address broader national security needs, such as foreign nuclear weapon assessments and counternuclear terrorism.« less

Simulation of Robot Kinematics Using Interactive Computer Graphics.

ERIC Educational Resources Information Center

Leu, M. C.; Mahajan, R.

1984-01-01

Development of a robot simulation program based on geometric transformation softwares available in most computer graphics systems and program features are described. The program can be extended to simulate robots coordinating with external devices (such as tools, fixtures, conveyors) using geometric transformations to describe the…

3D Simulation: Microgravity Environments and Applications

NASA Technical Reports Server (NTRS)

Hunter, Steve L.; Dischinger, Charles; Estes, Samantha; Parker, Nelson C. (Technical Monitor)

2001-01-01

Most, if not all, 3-D and Virtual Reality (VR) software programs are designed for one-G gravity applications. Space environments simulations require gravity effects of one one-thousandth to one one-million of that of the Earth's surface (10(exp -3) - 10(exp -6) G), thus one must be able to generate simulations that replicate those microgravity effects upon simulated astronauts. Unfortunately, the software programs utilized by the National Aeronautical and Space Administration does not have the ability to readily neutralize the one-G gravity effect. This pre-programmed situation causes the engineer or analysis difficulty during micro-gravity simulations. Therefore, microgravity simulations require special techniques or additional code in order to apply the power of 3D graphic simulation to space related applications. This paper discusses the problem and possible solutions to allow microgravity 3-D/VR simulations to be completed successfully without program code modifications.

Diesel Bus Performance Simulation Program

DOT National Transportation Integrated Search

1979-04-01

A diesel bus performance computer simulation program was developed. This program provides information on acceleration, velocity, horsepower, distance traveled, and fuel consumption as a function of time from the originating station. The program was w...

Space Ultrareliable Modular Computer (SUMC) instruction simulator

NASA Technical Reports Server (NTRS)

Curran, R. T.

1972-01-01

The design principles, description, functional operation, and recommended expansion and enhancements are presented for the Space Ultrareliable Modular Computer interpretive simulator. Included as appendices are the user's manual, program module descriptions, target instruction descriptions, simulator source program listing, and a sample program printout. In discussing the design and operation of the simulator, the key problems involving host computer independence and target computer architectural scope are brought into focus.

Simulator sickness research program at NASA-Ames Research Center

NASA Technical Reports Server (NTRS)

Mccauley, Michael E.; Cook, Anthony M.

1987-01-01

The simulator sickness syndrome is receiving increased attention in the simulation community. NASA-Ames Research Center has initiated a program to facilitate the exchange of information on this topic among the tri-services and other interested government organizations. The program objectives are to identify priority research issues, promote efficient research strategies, serve as a repository of information, and disseminate information to simulator users.

The effectiveness of simulated robots for supporting the learning of introductory programming: a multi-case case study

NASA Astrophysics Data System (ADS)

Major, Louis; Kyriacou, Theocharis; Brereton, Pearl

2014-07-01

This work investigates the effectiveness of simulated robots as tools to support the learning of programming. After the completion of a systematic review and exploratory research, a multi-case case study was undertaken. A simulator, named Kebot, was developed and used to run four 10-hour programming workshops. Twenty-three student participants (aged 16-18) in addition to 23 pre-service, and 3 in-service, teachers took part. The effectiveness of this intervention was determined by considering opinions, attitudes, and motivation as well as by analysing students' programming performance. Pre- and post-questionnaires, in- and post-workshop exercises, and interviews were used. Participants enjoyed learning using the simulator and believed the approach to be valuable and engaging. The performance of students indicates that the simulator aids learning as most completed tasks to a satisfactory standard. Evidence suggests robot simulators can offer an effective means of introducing programming. Recommendations to support the development of other simulators are provided.

Barriers to the implementation and uptake of simulation-based training programs in general surgery: a multinational qualitative study.

PubMed

Hosny, Shady G; Johnston, Maximilian J; Pucher, Philip H; Erridge, Simon; Darzi, Ara

2017-12-01

Despite evidence demonstrating the advantages of simulation training in general surgery, it is not widely integrated into surgical training programs worldwide. The aim of this study was to identify barriers and facilitators to the implementation and uptake of surgical simulation training programs. A multinational qualitative study was conducted using semi-structured interviews of general surgical residents and experts. Each interview was audio recorded, transcribed verbatim, and underwent emergent theme analysis. All data were anonymized and results pooled. A total of 37 individuals participated in the study. Seventeen experts (Program Directors and Surgical Attendings with an interest in surgical education) and 20 residents drawn from the United States, Canada, United Kingdom, France, and Japan were interviewed. Barriers to simulation-based training were identified based on key themes including financial cost, access, and translational benefit. Participants described cost (89%) and access (76%) as principal barriers to uptake. Common facilitators included a mandatory requirement to complete simulation training (78%) and on-going assessment of skills (78%). Participants felt that simulation training could improve patient outcomes (76%) but identified a lack of evidence to demonstrate benefit (38%). There was a consensus that simulation training has not been widely implemented (70%). There are multiple barriers to the implementation of surgical simulation training programs, however, there is agreement that these programs could potentially improve patient outcomes. Identifying these barriers enable the targeted use of facilitators to deliver simulation training programs. Copyright © 2017 Elsevier Inc. All rights reserved.

The transition of a real-time single-rotor helicopter simulation program to a supercomputer

NASA Technical Reports Server (NTRS)

Martinez, Debbie

1995-01-01

This report presents the conversion effort and results of a real-time flight simulation application transition to a CONVEX supercomputer. Enclosed is a detailed description of the conversion process and a brief description of the Langley Research Center's (LaRC) flight simulation application program structure. Currently, this simulation program may be configured to represent Sikorsky S-61 helicopter (a five-blade, single-rotor, commercial passenger-type helicopter) or an Army Cobra helicopter (either the AH-1 G or AH-1 S model). This report refers to the Sikorsky S-61 simulation program since it is the most frequently used configuration.

Program to Optimize Simulated Trajectories (POST). Volume 1: Formulation manual

NASA Technical Reports Server (NTRS)

Brauer, G. L.; Cornick, D. E.; Habeger, A. R.; Petersen, F. M.; Stevenson, R.

1975-01-01

A general purpose FORTRAN program for simulating and optimizing point mass trajectories (POST) of aerospace vehicles is described. The equations and the numerical techniques used in the program are documented. Topics discussed include: coordinate systems, planet model, trajectory simulation, auxiliary calculations, and targeting and optimization.

Users manual for linear Time-Varying Helicopter Simulation (Program TVHIS)

NASA Technical Reports Server (NTRS)

Burns, M. R.

1979-01-01

A linear time-varying helicopter simulation program (TVHIS) is described. The program is designed as a realistic yet efficient helicopter simulation. It is based on a linear time-varying helicopter model which includes rotor, actuator, and sensor models, as well as a simulation of flight computer logic. The TVHIS can generate a mean trajectory simulation along a nominal trajectory, or propagate covariance of helicopter states, including rigid-body, turbulence, control command, controller states, and rigid-body state estimates.

Medical Simulation Practices 2010 Survey Results

NASA Technical Reports Server (NTRS)

McCrindle, Jeffrey J.

2011-01-01

Medical Simulation Centers are an essential component of our learning infrastructure to prepare doctors and nurses for their careers. Unlike the military and aerospace simulation industry, very little has been published regarding the best practices currently in use within medical simulation centers. This survey attempts to provide insight into the current simulation practices at medical schools, hospitals, university nursing programs and community college nursing programs. Students within the MBA program at Saint Joseph's University conducted a survey of medical simulation practices during the summer 2010 semester. A total of 115 institutions responded to the survey. The survey resus discuss overall effectiveness of current simulation centers as well as the tools and techniques used to conduct the simulation activity

Program Code Generator for Cardiac Electrophysiology Simulation with Automatic PDE Boundary Condition Handling

PubMed Central

Punzalan, Florencio Rusty; Kunieda, Yoshitoshi; Amano, Akira

2015-01-01

Clinical and experimental studies involving human hearts can have certain limitations. Methods such as computer simulations can be an important alternative or supplemental tool. Physiological simulation at the tissue or organ level typically involves the handling of partial differential equations (PDEs). Boundary conditions and distributed parameters, such as those used in pharmacokinetics simulation, add to the complexity of the PDE solution. These factors can tailor PDE solutions and their corresponding program code to specific problems. Boundary condition and parameter changes in the customized code are usually prone to errors and time-consuming. We propose a general approach for handling PDEs and boundary conditions in computational models using a replacement scheme for discretization. This study is an extension of a program generator that we introduced in a previous publication. The program generator can generate code for multi-cell simulations of cardiac electrophysiology. Improvements to the system allow it to handle simultaneous equations in the biological function model as well as implicit PDE numerical schemes. The replacement scheme involves substituting all partial differential terms with numerical solution equations. Once the model and boundary equations are discretized with the numerical solution scheme, instances of the equations are generated to undergo dependency analysis. The result of the dependency analysis is then used to generate the program code. The resulting program code are in Java or C programming language. To validate the automatic handling of boundary conditions in the program code generator, we generated simulation code using the FHN, Luo-Rudy 1, and Hund-Rudy cell models and run cell-to-cell coupling and action potential propagation simulations. One of the simulations is based on a published experiment and simulation results are compared with the experimental data. We conclude that the proposed program code generator can be used to generate code for physiological simulations and provides a tool for studying cardiac electrophysiology. PMID:26356082

SimZones: An Organizational Innovation for Simulation Programs and Centers.

PubMed

Roussin, Christopher J; Weinstock, Peter

2017-08-01

The complexity and volume of simulation-based learning programs have increased dramatically over the last decade, presenting several major challenges for those who lead and manage simulation programs and centers. The authors present five major issues affecting the organization of simulation programs: (1) supporting both single- and double-loop learning experiences; (2) managing the training of simulation teaching faculty; (3) optimizing the participant mix, including individuals, professional groups, teams, and other role-players, to ensure learning; (4) balancing in situ, node-based, and center-based simulation delivery; and (5) organizing simulation research and measuring value. They then introduce the SimZones innovation, a system of organization for simulation-based learning, and explain how it can alleviate the problems associated with these five issues.Simulations are divided into four zones (Zones 0-3). Zone 0 simulations include autofeedback exercises typically practiced by solitary learners, often using virtual simulation technology. Zone 1 simulations include hands-on instruction of foundational clinical skills. Zone 2 simulations include acute situational instruction, such as clinical mock codes. Zone 3 simulations involve authentic, native teams of participants and facilitate team and system development.The authors also discuss the translation of debriefing methods from Zone 3 simulations to real patient care settings (Zone 4), and they illustrate how the SimZones approach can enable the development of longitudinal learning systems in both teaching and nonteaching hospitals. The SimZones approach was initially developed in the context of the Boston Children's Hospital Simulator Program, which the authors use to illustrate this innovation in action.

Planning Educational Programs: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; Pritz, Sandra

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with education, the report contains sections describing the simulation context, evaluation procedures,…

Simulation Higher Order Language Requirements Study.

ERIC Educational Resources Information Center

Goodenough, John B.; Braun, Christine L.

The definitions provided for high order language (HOL) requirements for programming flight training simulators are based on the analysis of programs written for a variety of simulators. Examples drawn from these programs are used to justify the need for certain HOL capabilities. A description of the general structure and organization of the…

Human-simulation-based learning to prevent medication error: A systematic review.

PubMed

Sarfati, Laura; Ranchon, Florence; Vantard, Nicolas; Schwiertz, Vérane; Larbre, Virginie; Parat, Stéphanie; Faudel, Amélie; Rioufol, Catherine

2018-01-31

In the past 2 decades, there has been an increasing interest in simulation-based learning programs to prevent medication error (ME). To improve knowledge, skills, and attitudes in prescribers, nurses, and pharmaceutical staff, these methods enable training without directly involving patients. However, best practices for simulation for healthcare providers are as yet undefined. By analysing the current state of experience in the field, the present review aims to assess whether human simulation in healthcare helps to reduce ME. A systematic review was conducted on Medline from 2000 to June 2015, associating the terms "Patient Simulation," "Medication Errors," and "Simulation Healthcare." Reports of technology-based simulation were excluded, to focus exclusively on human simulation in nontechnical skills learning. Twenty-one studies assessing simulation-based learning programs were selected, focusing on pharmacy, medicine or nursing students, or concerning programs aimed at reducing administration or preparation errors, managing crises, or learning communication skills for healthcare professionals. The studies varied in design, methodology, and assessment criteria. Few demonstrated that simulation was more effective than didactic learning in reducing ME. This review highlights a lack of long-term assessment and real-life extrapolation, with limited scenarios and participant samples. These various experiences, however, help in identifying the key elements required for an effective human simulation-based learning program for ME prevention: ie, scenario design, debriefing, and perception assessment. The performance of these programs depends on their ability to reflect reality and on professional guidance. Properly regulated simulation is a good way to train staff in events that happen only exceptionally, as well as in standard daily activities. By integrating human factors, simulation seems to be effective in preventing iatrogenic risk related to ME, if the program is well designed. © 2018 John Wiley & Sons, Ltd.

Development of a multi-media crew-training program for the Terminal Configured Vehicle Mission Simulator

NASA Technical Reports Server (NTRS)

Houck, J. A.; Markos, A. T.

1980-01-01

This paper describes the work being done at the National Aeronautics and Space Administration's (NASA) Langley Research Center on the development of a multi-media crew-training program for the Terminal Configured Vehicle (TCV) Mission Simulator. Brief descriptions of the goals and objectives of the TCV Program and of the TCV Mission Simulator are presented. A detailed description of the training program is provided along with a description of the performance of the first group of four commercial pilots to be qualified in the TCV Mission Simulator.

Development of a multi-media crew-training program for the terminal configured vehicle mission simulator

NASA Technical Reports Server (NTRS)

Rhouck, J. A.; Markos, A. T.

1980-01-01

This paper describes the work being done at the National Aeronautics and Space Administration's (NASA) Langley Research Center on the development of a multi-media crew-training program for the Terminal Configured Vehicle (TCV) Mission Simulator. Brief descriptions of the goals and objectives of the TCV Program and of the TCV Mission Simulator are presented. A detailed description of the training program is provided along with a description of the performance of the first group of four commercial pilots to be qualified in the TCV Mission Simulator.

Concurrent simulation of a parallel jaw end effector

NASA Technical Reports Server (NTRS)

Bynum, Bill

1985-01-01

A system of programs developed to aid in the design and development of the command/response protocol between a parallel jaw end effector and the strategic planner program controlling it are presented. The system executes concurrently with the LISP controlling program to generate a graphical image of the end effector that moves in approximately real time in response to commands sent from the controlling program. Concurrent execution of the simulation program is useful for revealing flaws in the communication command structure arising from the asynchronous nature of the message traffic between the end effector and the strategic planner. Software simulation helps to minimize the number of hardware changes necessary to the microprocessor driving the end effector because of changes in the communication protocol. The simulation of other actuator devices can be easily incorporated into the system of programs by using the underlying support that was developed for the concurrent execution of the simulation process and the communication between it and the controlling program.

A real-time digital computer program for the simulation of automatic spacecraft reentries

NASA Technical Reports Server (NTRS)

Kaylor, J. T.; Powell, L. F.; Powell, R. W.

1977-01-01

The automatic reentry flight dynamics simulator, a nonlinear, six-degree-of-freedom simulation, digital computer program, has been developed. The program includes a rotating, oblate earth model for accurate navigation calculations and contains adjustable gains on the aerodynamic stability and control parameters. This program uses a real-time simulation system and is designed to examine entries of vehicles which have constant mass properties whose attitudes are controlled by both aerodynamic surfaces and reaction control thrusters, and which have automatic guidance and control systems. The program has been used to study the space shuttle orbiter entry. This report includes descriptions of the equations of motion used, the control and guidance schemes that were implemented, the program flow and operation, and the hardware involved.

A coupled hydrodynamic-hydrochemical modeling for predicting mineral transport in a natural acid drainage system.

NASA Astrophysics Data System (ADS)

Zegers Risopatron, G., Sr.; Navarro, L.; Montserrat, S., Sr.; McPhee, J. P.; Niño, Y.

2017-12-01

The geochemistry of water and sediments, coupled with hydrodynamic transport in mountainous channels, is of particular interest in central Chilean Andes due to natural occurrence of acid waters. In this paper, we present a coupled transport and geochemical model to estimate and understand transport processes and fate of minerals at the Yerba Loca Basin, located near Santiago, Chile. In the upper zone, water presentes low pH ( 3) and high concentrations of iron, aluminum, copper, manganese and zinc. Acidity and minerals are the consequence of water-rock interactions in hydrothermal alteration zones, rich in sulphides and sulphates, covered by seasonal snow and glaciers. Downstream, as a consequence of neutral to alkaline lateral water contributions (pH >7) along the river, pH increases and concentration of solutes decreases. The mineral transport model has three components: (i) a hydrodynamic model, where we use HEC-RAS to solve 1D Saint-Venant equations, (ii) a sediment transport model to estimate erosion and sedimentation rates, which quantify minerals transference between water and riverbed and (iii) a solute transport model, based on the 1D OTIS model which takes into account the temporal delay in solutes transport that typically is observed in natural channels (transient storage). Hydrochemistry is solved using PHREEQC, a software for speciation and batch reaction. Our results show that correlation between mineral precipitation and dissolution according to pH values changes along the river. Based on pH measurements (and according to literature) we inferred that main minerals in the water system are brochantite, ferrihydrite, hydrobasaluminite and schwertmannite. Results show that our model can predict the transport and fate of minerals and metals in the Yerba Loca Basin. Mineral dissolution and precipitation process occur for limited ranges of pH values. When pH values are increased, iron minerals (schwertmannite) are the first to precipitate ( 2.5

LOFT L2-3 blowdown experiment safety analyses D, E, and G; LOCA analyses H, K, K1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perryman, J.L.; Keeler, C.D.; Saukkoriipi, L.O.

1978-12-01

Three calculations using conservative off-nominal conditions and evaluation model options were made using RELAP4/MOD5 for blowdown-refill and RELAP4/MOD6 for reflood for Loss-of-Fluid Test Experiment L2-3 to support the experiment safety analysis effort. The three analyses are as follows: Analysis D: Loss of commercial power during Experiment L2-3; Analysis E: Hot leg quick-opening blowdown valve (QOBV) does not open during Experiment L2-3; and Analysis G: Cold leg QOBV does not open during Experiment L2-3. In addition, the results of three LOFT loss-of-coolant accident (LOCA) analyses using a power of 56.1 MW and a primary coolant system flow rate of 3.6 millionmore » 1bm/hr are presented: Analysis H: Intact loop 200% hot leg break; emergency core cooling (ECC) system B unavailable; Analysis K: Pressurizer relief valve stuck in open position; ECC system B unavailable; and Analysis K1: Same as analysis K, but using a primary coolant system flow rate of 1.92 million 1bm/hr (L2-4 pre-LOCE flow rate). For analysis D, the maximum cladding temperature reached was 1762/sup 0/F, 22 sec into reflood. In analyses E and G, the blowdowns were slower due to one of the QOBVs not functioning. The maximum cladding temperature reached in analysis E was 1700/sup 0/F, 64.7 sec into reflood; for analysis G, it was 1300/sup 0/F at the start of reflood. For analysis H, the maximum cladding temperature reached was 1825/sup 0/F, 0.01 sec into reflood. Analysis K was a very slow blowdown, and the cladding temperatures followed the saturation temperature of the system. The results of analysis K1 was nearly identical to analysis K; system depressurization was not affected by the primary coolant system flow rate.« less

Advanced Simulation and Computing Fiscal Year 14 Implementation Plan, Rev. 0.5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meisner, Robert; McCoy, Michel; Archer, Bill

2013-09-11

The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the surety and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities andmore » computational resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balanced resource, including technical staff, hardware, simulation software, and computer science solutions. In its first decade, the ASC strategy focused on demonstrating simulation capabilities of unprecedented scale in three spatial dimensions. In its second decade, ASC is now focused on increasing predictive capabilities in a three-dimensional (3D) simulation environment while maintaining support to the SSP. The program continues to improve its unique tools for solving progressively more difficult stockpile problems (sufficient resolution, dimensionality, and scientific details), quantify critical margins and uncertainties, and resolve increasingly difficult analyses needed for the SSP. Moreover, ASC’s business model is integrated and focused on requirements-driven products that address long-standing technical questions related to enhanced predictive capability in the simulation tools.« less

SMMP v. 3.0—Simulating proteins and protein interactions in Python and Fortran

NASA Astrophysics Data System (ADS)

Meinke, Jan H.; Mohanty, Sandipan; Eisenmenger, Frank; Hansmann, Ulrich H. E.

2008-03-01

We describe a revised and updated version of the program package SMMP. SMMP is an open-source FORTRAN package for molecular simulation of proteins within the standard geometry model. It is designed as a simple and inexpensive tool for researchers and students to become familiar with protein simulation techniques. SMMP 3.0 sports a revised API increasing its flexibility, an implementation of the Lund force field, multi-molecule simulations, a parallel implementation of the energy function, Python bindings, and more. Program summaryTitle of program:SMMP Catalogue identifier:ADOJ_v3_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADOJ_v3_0.html Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Licensing provisions:Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html Programming language used:FORTRAN, Python No. of lines in distributed program, including test data, etc.:52 105 No. of bytes in distributed program, including test data, etc.:599 150 Distribution format:tar.gz Computer:Platform independent Operating system:OS independent RAM:2 Mbytes Classification:3 Does the new version supersede the previous version?:Yes Nature of problem:Molecular mechanics computations and Monte Carlo simulation of proteins. Solution method:Utilizes ECEPP2/3, FLEX, and Lund potentials. Includes Monte Carlo simulation algorithms for canonical, as well as for generalized ensembles. Reasons for new version:API changes and increased functionality. Summary of revisions:Added Lund potential; parameters used in subroutines are now passed as arguments; multi-molecule simulations; parallelized energy calculation for ECEPP; Python bindings. Restrictions:The consumed CPU time increases with the size of protein molecule. Running time:Depends on the size of the simulated molecule.

SimulCAT: Windows Software for Simulating Computerized Adaptive Test Administration

ERIC Educational Resources Information Center

Han, Kyung T.

2012-01-01

Most, if not all, computerized adaptive testing (CAT) programs use simulation techniques to develop and evaluate CAT program administration and operations, but such simulation tools are rarely available to the public. Up to now, several software tools have been available to conduct CAT simulations for research purposes; however, these existing…

Real time digital propulsion system simulation for manned flight simulators

NASA Technical Reports Server (NTRS)

Mihaloew, J. R.; Hart, C. E.

1978-01-01

A real time digital simulation of a STOL propulsion system was developed which generates significant dynamics and internal variables needed to evaluate system performance and aircraft interactions using manned flight simulators. The simulation ran at a real-to-execution time ratio of 8.8. The model was used in a piloted NASA flight simulator program to evaluate the simulation technique and the propulsion system digital control. The simulation is described and results shown. Limited results of the flight simulation program are also presented.

AMPS/PC - AUTOMATIC MANUFACTURING PROGRAMMING SYSTEM

NASA Technical Reports Server (NTRS)

Schroer, B. J.

1994-01-01

The AMPS/PC system is a simulation tool designed to aid the user in defining the specifications of a manufacturing environment and then automatically writing code for the target simulation language, GPSS/PC. The domain of problems that AMPS/PC can simulate are manufacturing assembly lines with subassembly lines and manufacturing cells. The user defines the problem domain by responding to the questions from the interface program. Based on the responses, the interface program creates an internal problem specification file. This file includes the manufacturing process network flow and the attributes for all stations, cells, and stock points. AMPS then uses the problem specification file as input for the automatic code generator program to produce a simulation program in the target language GPSS. The output of the generator program is the source code of the corresponding GPSS/PC simulation program. The system runs entirely on an IBM PC running PC DOS Version 2.0 or higher and is written in Turbo Pascal Version 4 requiring 640K memory and one 360K disk drive. To execute the GPSS program, the PC must have resident the GPSS/PC System Version 2.0 from Minuteman Software. The AMPS/PC program was developed in 1988.

Transient Analysis Generator /TAG/ simulates behavior of large class of electrical networks

NASA Technical Reports Server (NTRS)

Thomas, W. J.

1967-01-01

Transient Analysis Generator program simulates both transient and dc steady-state behavior of a large class of electrical networks. It generates a special analysis program for each circuit described in an easily understood and manipulated programming language. A generator or preprocessor and a simulation system make up the TAG system.

Optimization Research of Generation Investment Based on Linear Programming Model

NASA Astrophysics Data System (ADS)

Wu, Juan; Ge, Xueqian

Linear programming is an important branch of operational research and it is a mathematical method to assist the people to carry out scientific management. GAMS is an advanced simulation and optimization modeling language and it will combine a large number of complex mathematical programming, such as linear programming LP, nonlinear programming NLP, MIP and other mixed-integer programming with the system simulation. In this paper, based on the linear programming model, the optimized investment decision-making of generation is simulated and analyzed. At last, the optimal installed capacity of power plants and the final total cost are got, which provides the rational decision-making basis for optimized investments.

User's Guide to Galoper: A Program for Simulating the Shapes of Crystal Size Distributions from Growth Mechanisms - and Associated Programs

USGS Publications Warehouse

Eberl, Dennis D.; Drits, V.A.; Srodon, J.

2000-01-01

GALOPER is a computer program that simulates the shapes of crystal size distributions (CSDs) from crystal growth mechanisms. This manual describes how to use the program. The theory for the program's operation has been described previously (Eberl, Drits, and Srodon, 1998). CSDs that can be simulated using GALOPER include those that result from growth mechanisms operating in the open system, such as constant-rate nucleation and growth, nucleation with a decaying nucleation rate and growth, surface-controlled growth, supply-controlled growth, and constant-rate and random growth; and those that result from mechanisms operating in the closed system such as Ostwald ripening, random ripening, and crystal coalescence. In addition, CSDs for two types weathering reactions can be simulated. The operation of associated programs also is described, including two statistical programs used for comparing calculated with measured CSDs, a program used for calculating lognormal CSDs, and a program for arranging measured crystal sizes into size groupings (bins).

AESS: Accelerated Exact Stochastic Simulation

NASA Astrophysics Data System (ADS)

Jenkins, David D.; Peterson, Gregory D.

2011-12-01

The Stochastic Simulation Algorithm (SSA) developed by Gillespie provides a powerful mechanism for exploring the behavior of chemical systems with small species populations or with important noise contributions. Gene circuit simulations for systems biology commonly employ the SSA method, as do ecological applications. This algorithm tends to be computationally expensive, so researchers seek an efficient implementation of SSA. In this program package, the Accelerated Exact Stochastic Simulation Algorithm (AESS) contains optimized implementations of Gillespie's SSA that improve the performance of individual simulation runs or ensembles of simulations used for sweeping parameters or to provide statistically significant results. Program summaryProgram title: AESS Catalogue identifier: AEJW_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEJW_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: University of Tennessee copyright agreement No. of lines in distributed program, including test data, etc.: 10 861 No. of bytes in distributed program, including test data, etc.: 394 631 Distribution format: tar.gz Programming language: C for processors, CUDA for NVIDIA GPUs Computer: Developed and tested on various x86 computers and NVIDIA C1060 Tesla and GTX 480 Fermi GPUs. The system targets x86 workstations, optionally with multicore processors or NVIDIA GPUs as accelerators. Operating system: Tested under Ubuntu Linux OS and CentOS 5.5 Linux OS Classification: 3, 16.12 Nature of problem: Simulation of chemical systems, particularly with low species populations, can be accurately performed using Gillespie's method of stochastic simulation. Numerous variations on the original stochastic simulation algorithm have been developed, including approaches that produce results with statistics that exactly match the chemical master equation (CME) as well as other approaches that approximate the CME. Solution method: The Accelerated Exact Stochastic Simulation (AESS) tool provides implementations of a wide variety of popular variations on the Gillespie method. Users can select the specific algorithm considered most appropriate. Comparisons between the methods and with other available implementations indicate that AESS provides the fastest known implementation of Gillespie's method for a variety of test models. Users may wish to execute ensembles of simulations to sweep parameters or to obtain better statistical results, so AESS supports acceleration of ensembles of simulation using parallel processing with MPI, SSE vector units on x86 processors, and/or using NVIDIA GPUs with CUDA.

Digital Simulation in Education.

ERIC Educational Resources Information Center

Braun, Ludwig

Simulation as a mode of computer use in instruction has been neglected by educators. This paper briefly explores the circumstances in which simulations are useful and presents several examples of simulation programs currently being used in high-school biology, chemistry, physics, and social studies classes. One program, STERIL, which simulates…

Formulation of consumables management models: Consumables analysis/crew simulator interface requirements

NASA Technical Reports Server (NTRS)

Zamora, M. A.

1977-01-01

Consumables analysis/crew training simulator interface requirements were defined. Two aspects were investigated: consumables analysis support techniques to crew training simulator for advanced spacecraft programs, and the applicability of the above techniques to the crew training simulator for the space shuttle program in particular.

Monte Carlo Computer Simulation of a Rainbow.

ERIC Educational Resources Information Center

Olson, Donald; And Others

1990-01-01

Discusses making a computer-simulated rainbow using principles of physics, such as reflection and refraction. Provides BASIC program for the simulation. Appends a program illustrating the effects of dispersion of the colors. (YP)

Enhanced TCAS 2/CDTI traffic Sensor digital simulation model and program description

NASA Technical Reports Server (NTRS)

Goka, T.

1984-01-01

Digital simulation models of enhanced TCAS 2/CDTI traffic sensors are developed, based on actual or projected operational and performance characteristics. Two enhanced Traffic (or Threat) Alert and Collision Avoidance Systems are considered. A digital simulation program is developed in FORTRAN. The program contains an executive with a semireal time batch processing capability. The simulation program can be interfaced with other modules with a minimum requirement. Both the traffic sensor and CAS logic modules are validated by means of extensive simulation runs. Selected validation cases are discussed in detail, and capabilities and limitations of the actual and simulated systems are noted. The TCAS systems are not specifically intended for Cockpit Display of Traffic Information (CDTI) applications. These systems are sufficiently general to allow implementation of CDTI functions within the real systems' constraints.

Introducing a laparoscopic simulation training and credentialing program in gynaecology: an observational study.

PubMed

Janssens, Sarah; Beckmann, Michael; Bonney, Donna

2015-08-01

Simulation training in laparoscopic surgery has been shown to improve surgical performance. To describe the implementation of a laparoscopic simulation training and credentialing program for gynaecology registrars. A pilot program consisting of protected, supervised laparoscopic simulation time, a tailored curriculum and a credentialing process, was developed and implemented. Quantitative measures assessing simulated surgical performance were measured over the simulation training period. Laparoscopic procedures requiring credentialing were assessed for both the frequency of a registrar being the primary operator and the duration of surgery and compared to a presimulation cohort. Qualitative measures regarding quality of surgical training were assessed pre- and postsimulation. Improvements were seen in simulated surgical performance in efficiency domains. Operative time for procedures requiring credentialing was reduced by 12%. Primary operator status in the operating theatre for registrars was unchanged. Registrar assessment of training quality improved. The introduction of a laparoscopic simulation training and credentialing program resulted in improvements in simulated performance, reduced operative time and improved registrar assessment of the quality of training. © 2015 The Royal Australian and New Zealand College of Obstetricians and Gynaecologists.

Residents' perspectives of the value of a simulation curriculum in a general surgery residency program: a multimethod study of stakeholder feedback.

PubMed

Wehbe-Janek, Hania; Colbert, Colleen Y; Govednik-Horny, Cara; White, Bobbie Ann A; Thomas, Scott; Shabahang, Mohsen

2012-06-01

Simulation has altered surgical curricula throughout residency programs. The purpose of this multimethod study was to explore residents' perceptions of simulation within surgical residency as relevant stakeholder feedback and program evaluation of the surgery simulation curriculum. Focus groups were held with a sample of surgery residents (n = 25) at a university-affiliated program. Residents participated in focus groups based on level of training and completed questionnaires regarding simulation curricula. Groups were facilitated by nonsurgeon faculty. Residents were asked: "What is the role of simulation in surgical education?" An interdisciplinary team recorded narrative data and performed content analyses. Quantitative data from questionnaires were summarized using descriptive statistics and frequencies. Major themes from the qualitative data included: concerns regarding simulation in surgical education (28%), exposure to situations and technical skills in a low-stress learning environment (24%), pressure by external agencies (19%), an educational tool (17%), and quality assurance for patient care (12%). Laparoscopy and cadaver lab were the most prevalent simulation training during residency, in addition to trauma simulations, central lines/chest tubes/IV access, and stapling lab. In response to the statement: "ACGME should require a simulation curriculum in surgery residency," 52.1% responded favorably and 47.8% responded nonfavorably. Residents acknowledge the value of simulation in patient safety, quality, and exposure to procedures before clinical experience, but remain divided on efficacy and requirement of simulation within curricula. The greater challenge to residency programs may be strategic implementation of simulation curricula within the right training context. Copyright © 2012 Mosby, Inc. All rights reserved.

Simulation of a combined-cycle engine

NASA Technical Reports Server (NTRS)

Vangerpen, Jon

1991-01-01

A FORTRAN computer program was developed to simulate the performance of combined-cycle engines. These engines combine features of both gas turbines and reciprocating engines. The computer program can simulate both design point and off-design operation. Widely varying engine configurations can be evaluated for their power, performance, and efficiency as well as the influence of altitude and air speed. Although the program was developed to simulate aircraft engines, it can be used with equal success for stationary and automative applications.

Exploring the Perceptions of College Instructors towards Computer Simulation Software Programs: A Quantitative Study

ERIC Educational Resources Information Center

Punch, Raymond J.

2012-01-01

The purpose of the quantitative regression study was to explore and to identify relationships between attitudes toward use and perceptions of value of computer-based simulation programs, of college instructors, toward computer based simulation programs. A relationship has been reported between attitudes toward use and perceptions of the value of…

Advanced Simulation and Computing Business Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rummel, E.

To maintain a credible nuclear weapons program, the National Nuclear Security Administration’s (NNSA’s) Office of Defense Programs (DP) needs to make certain that the capabilities, tools, and expert staff are in place and are able to deliver validated assessments. This requires a complete and robust simulation environment backed by an experimental program to test ASC Program models. This ASC Business Plan document encapsulates a complex set of elements, each of which is essential to the success of the simulation component of the Nuclear Security Enterprise. The ASC Business Plan addresses the hiring, mentoring, and retaining of programmatic technical staff responsiblemore » for building the simulation tools of the nuclear security complex. The ASC Business Plan describes how the ASC Program engages with industry partners—partners upon whom the ASC Program relies on for today’s and tomorrow’s high performance architectures. Each piece in this chain is essential to assure policymakers, who must make decisions based on the results of simulations, that they are receiving all the actionable information they need.« less

specsim: A Fortran-77 program for conditional spectral simulation in 3D

NASA Astrophysics Data System (ADS)

Yao, Tingting

1998-12-01

A Fortran 77 program, specsim, is presented for conditional spectral simulation in 3D domains. The traditional Fourier integral method allows generating random fields with a given covariance spectrum. Conditioning to local data is achieved by an iterative identification of the conditional phase information. A flowchart of the program is given to illustrate the implementation procedures of the program. A 3D case study is presented to demonstrate application of the program. A comparison with the traditional sequential Gaussian simulation algorithm emphasizes the advantages and drawbacks of the proposed algorithm.

Use of multiscale zirconium alloy deformation models in nuclear fuel behavior analysis

NASA Astrophysics Data System (ADS)

Montgomery, Robert; Tomé, Carlos; Liu, Wenfeng; Alankar, Alankar; Subramanian, Gopinath; Stanek, Christopher

2017-01-01

Accurate prediction of cladding mechanical behavior is a key aspect of modeling nuclear fuel behavior, especially for conditions of pellet-cladding interaction (PCI), reactivity-initiated accidents (RIA), and loss of coolant accidents (LOCA). Current approaches to fuel performance modeling rely on empirical constitutive models for cladding creep, growth and plastic deformation, which are limited to the materials and conditions for which the models were developed. To improve upon this approach, a microstructurally-based zirconium alloy mechanical deformation analysis capability is being developed within the United States Department of Energy Consortium for Advanced Simulation of Light Water Reactors (CASL). Specifically, the viscoplastic self-consistent (VPSC) polycrystal plasticity modeling approach, developed by Lebensohn and Tomé [1], has been coupled with the BISON engineering scale fuel performance code to represent the mechanistic material processes controlling the deformation behavior of light water reactor (LWR) cladding. A critical component of VPSC is the representation of the crystallographic nature (defect and dislocation movement) and orientation of the grains within the matrix material and the ability to account for the role of texture on deformation. A future goal is for VPSC to obtain information on reaction rate kinetics from atomistic calculations to inform the defect and dislocation behavior models described in VPSC. The multiscale modeling of cladding deformation mechanisms allowed by VPSC far exceed the functionality of typical semi-empirical constitutive models employed in nuclear fuel behavior codes to model irradiation growth and creep, thermal creep, or plasticity. This paper describes the implementation of an interface between VPSC and BISON and provides initial results utilizing the coupled functionality.

Comparison of Cardiopulmonary Resuscitation Quality Between Standard Versus Telephone-Basic Life Support Training Program in Middle-Aged and Elderly Housewives: A Randomized Simulation Study.

PubMed

Kim, Tae Han; Lee, Yu Jin; Lee, Eui Jung; Ro, Young Sun; Lee, KyungWon; Lee, Hyeona; Jang, Dayea Beatrice; Song, Kyoung Jun; Shin, Sang Do; Myklebust, Helge; Birkenes, Tonje Søraas

2018-02-01

For cardiac arrests witnessed at home, the witness is usually a middle-aged or older housewife. We compared the quality of cardiopulmonary resuscitation (CPR) performance of bystanders trained with the newly developed telephone-basic life support (T-BLS) program and those trained with standard BLS (S-BLS) training programs. Twenty-four middle-aged and older housewives without previous CPR education were enrolled and randomized into two groups of BLS training programs. The T-BLS training program included concepts and current instruction protocols for telephone-assisted CPR, whereas the S-BLS training program provided training for BLS. After each training course, the participants simulated CPR and were assisted by a dispatcher via telephone. Cardiopulmonary resuscitation quality was measured and recorded using a mannequin simulator. The primary outcome was total no-flow time (>1.5 seconds without chest compression) during simulation. Among 24 participants, two (8.3%) who experienced mechanical failure of simulation mannequin and one (4.2%) who violated simulation protocols were excluded at initial simulation, and two (8.3%) refused follow-up after 6 months. The median (interquartile range) total no-flow time during initial simulation was 79.6 (66.4-96.9) seconds for the T-BLS training group and 147.6 (122.5-184.0) seconds for the S-BLS training group (P < 0.01). Median cumulative interruption time and median number of interruption events during BLS at initial simulation and 6-month follow-up simulation were significantly shorter in the T-BLS than in the S-BLS group (1.0 vs. 9.5, P < 0.01, and 1.0 vs. 10.5, P = 0.02, respectively). Participants trained with the T-BLS training program showed shorter no-flow time and fewer interruptions during bystander CPR simulation assisted by a dispatcher.

Passive containment cooling system with drywell pressure regulation for boiling water reactor

DOEpatents

Hill, P.R.

1994-12-27

A boiling water reactor is described having a regulating valve for placing the wetwell in flow communication with an intake duct of the passive containment cooling system. This subsystem can be adjusted to maintain the drywell pressure at (or slightly below or above) wetwell pressure after the initial reactor blowdown transient is over. This addition to the PCCS design has the benefit of eliminating or minimizing steam leakage from the drywell to the wetwell in the longer-term post-LOCA time period and also minimizes the temperature difference between drywell and wetwell. This in turn reduces the rate of long-term pressure buildup of the containment, thereby extending the time to reach the design pressure limit. 4 figures.

A Teaching Aid for Physiologists--Simulation of Kidney Function

ERIC Educational Resources Information Center

Packer, J. S.; Packer, J. E.

1977-01-01

Presented is the development of a simulation model of the facultative water transfer mechanism of the mammalian kidney. Discussion topics include simulation philosophy, simulation facilities, the model, and programming the model as a teaching aid. Graphs illustrate typical program displays. A listing of references concludes the article. (MA)

Comparison of optimization algorithms in intensity-modulated radiation therapy planning

NASA Astrophysics Data System (ADS)

Kendrick, Rachel

Intensity-modulated radiation therapy is used to better conform the radiation dose to the target, which includes avoiding healthy tissue. Planning programs employ optimization methods to search for the best fluence of each photon beam, and therefore to create the best treatment plan. The Computational Environment for Radiotherapy Research (CERR), a program written in MATLAB, was used to examine some commonly-used algorithms for one 5-beam plan. Algorithms include the genetic algorithm, quadratic programming, pattern search, constrained nonlinear optimization, simulated annealing, the optimization method used in Varian EclipseTM, and some hybrids of these. Quadratic programing, simulated annealing, and a quadratic/simulated annealing hybrid were also separately compared using different prescription doses. The results of each dose-volume histogram as well as the visual dose color wash were used to compare the plans. CERR's built-in quadratic programming provided the best overall plan, but avoidance of the organ-at-risk was rivaled by other programs. Hybrids of quadratic programming with some of these algorithms seems to suggest the possibility of better planning programs, as shown by the improved quadratic/simulated annealing plan when compared to the simulated annealing algorithm alone. Further experimentation will be done to improve cost functions and computational time.

Man-rated flight software for the F-8 DFBW program

NASA Technical Reports Server (NTRS)

Bairnsfather, R. R.

1975-01-01

The design, implementation, and verification of the flight control software used in the F-8 DFBW program are discussed. Since the DFBW utilizes an Apollo computer and hardware, the procedures, controls, and basic management techniques employed are based on those developed for the Apollo software system. Program Assembly Control, simulator configuration control, erasable-memory load generation, change procedures and anomaly reporting are discussed. The primary verification tools--the all-digital simulator, the hybrid simulator, and the Iron Bird simulator--are described, as well as the program test plans and their implementation on the various simulators. Failure-effects analysis and the creation of special failure-generating software for testing purposes are described. The quality of the end product is evidenced by the F-8 DFBW flight test program in which 42 flights, totaling 58 hours of flight time, were successfully made without any DFCS inflight software, or hardware, failures.

Microcomputer Simulated CAD for Engineering Graphics.

ERIC Educational Resources Information Center

Huggins, David L.; Myers, Roy E.

1983-01-01

Describes a simulated computer-aided-graphics (CAD) program at The Pennsylvania State University. Rationale for the program, facilities, microcomputer equipment (Apple) used, and development of a software package for simulating applied engineering graphics are considered. (JN)

Ion trap simulation program, ITSIM: A powerful heuristic and predictive tool in ion trap mass spectrometry

NASA Astrophysics Data System (ADS)

Bui, Huy Anh

The multi-particle simulation program, ITSIM version 4.0, takes advantage of the enhanced performance of the Windows 95 and NT operating systems in areas such as memory management, user friendliness, flexibility of graphics and speed, to investigate the motion of ions in the quadrupole ion trap. The objective of this program is to use computer simulations based on mathematical models to improve the performance of the ion trap mass spectrometer. The simulation program can provide assistance in understanding fundamental aspects of ion trap mass spectrometry, precede and help to direct the course of experiments, as well as having didactic value in elucidating and allowing visualization of ion behavior under different experimental conditions. The program uses the improved Euler method to calculate ion trajectories as numerical solutions to the Mathieu differential equation. This Windows version can simultaneously simulate the trajectories of ions with a virtually unlimited number of different mass-to-charge ratios and hence allows realistic mass spectra, ion kinetic energy distributions and other experimentally measurable properties to be simulated. The large number of simulated ions allows examination of (i) the offsetting effects of mutual ion repulsion and collisional cooling in an ion trap and (ii) the effects of higher order fields. Field inhomogeneities arising from exit holes, electrode misalignment, imperfect electrode surfaces or new trap geometries can be simulated with the program. The simulated data are used to obtain mass spectra from mass-selective instability scans as well as by Fourier transformation of image currents induced by coherently moving ion clouds. Complete instruments, from an ion source through the ion trap mass analyzer to a detector, can now be simulated. Applications of the simulation program are presented and discussed. Comparisons are made between the simulations and experimental data. Fourier transformed experiments and a novel six-electrode ion trap mass spectrometer illustrate cases in which simulations precede new experiments. Broadband non-destructive ion detection based on induced image current measurements are described in the case of a quadrupole ion trap having cylindrical geometry.

NAVSIM 2: A computer program for simulating aided-inertial navigation for aircraft

NASA Technical Reports Server (NTRS)

Bjorkman, William S.

1987-01-01

NAVSIM II, a computer program for analytical simulation of aided-inertial navigation for aircraft, is described. The description is supported by a discussion of the program's application to the design and analysis of aided-inertial navigation systems as well as instructions for utilizing the program and for modifying it to accommodate new models, constraints, algorithms and scenarios. NAVSIM II simulates an airborne inertial navigation system built around a strapped-down inertial measurement unit and aided in its function by GPS, Doppler radar, altimeter, airspeed, and position-fix measurements. The measurements are incorporated into the navigation estimate via a UD-form Kalman filter. The simulation was designed and implemented using structured programming techniques and with particular attention to user-friendly operation.

Program to Optimize Simulated Trajectories (POST). Volume 3: Programmer's manual

NASA Technical Reports Server (NTRS)

Brauer, G. L.; Cornick, D. E.; Habeger, A. R.; Petersen, F. M.; Stevenson, R.

1975-01-01

Information pertinent to the programmer and relating to the program to optimize simulated trajectories (POST) is presented. Topics discussed include: program structure and logic, subroutine listings and flow charts, and internal FORTRAN symbols. The POST core requirements are summarized along with program macrologic.

Incorporating scenario-based simulation into a hospital nursing education program.

PubMed

Nagle, Beth M; McHale, Jeanne M; Alexander, Gail A; French, Brian M

2009-01-01

Nurse educators are challenged to provide meaningful and effective learning opportunities for both new and experienced nurses. Simulation as a teaching and learning methodology is being embraced by nursing in academic and practice settings to provide innovative educational experiences to assess and develop clinical competency, promote teamwork, and improve care processes. This article provides an overview of the historical basis for using simulation in education, simulation methodologies, and perceived advantages and disadvantages. It also provides a description of the integration of scenario-based programs using a full-scale patient simulator into nursing education programming at a large academic medical center.

A survey of electric and hybrid vehicle simulation programs

NASA Technical Reports Server (NTRS)

Bevan, J.; Heimburger, D. A.; Metcalfe, M. A.

1978-01-01

Results of a survey conducted within the United States to determine the extent of development and capabilities of automotive performance simulation programs suitable for electric and hybrid vehicle studies are summarized. Altogether, 111 programs were identified as being in a usable state. The complexity of the existing programs spans a range from a page of simple desktop calculator instructions to 300,000 lines of a high-level programming language. The capability to simulate electric vehicles was most common, heat-engines second, and hybrid vehicles least common. Batch-operated programs are slightly more common than interactive ones, and one-third can be operated in either mode. The most commonly used language was FORTRAN, the language typically used by engineers. The higher-level simulation languages (e.g. SIMSCRIPT, GPSS, SIMULA) used by "model builders" were conspicuously lacking.

ASC FY17 Implementation Plan, Rev. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamilton, P. G.

The Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, surety, and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational capabilities to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computationalmore » resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balance of resources, including technical staff, hardware, simulation software, and computer science solutions.« less

Simulation in the Internet age: the place of web-based simulation in nursing education. An integrative review.

PubMed

Cant, Robyn P; Cooper, Simon J

2014-12-01

The objective of this article was to review the literature on utilisation and place of Web-based simulation within nursing education. Web-based simulation combines electronic multimedia options with a central video or virtual world to produce interactive learning activities mediated by the learner. An integrative review. A search was conducted of healthcare databases between 2000 and 2014 and of Internet sources for hosted simulation programs in nursing. Eighteen primary programs were identified for inclusion. A strategy for integrative review was adopted in which studies were identified, filtered, classified, analysed and compared. Of 18 programs, two game-based programs were identified which represented a 'virtual world' in which students could simultaneously or individually immerse themselves in a character role-play. However, most programs (n=10) taught an aspect of procedural patient care using multimedia (e.g. video, audio, graphics, quiz, text, memo). Time-limited sequences, feedback and reflective activities were often incorporated. Other studies (n=8) taught interpersonal communication skills or technical skills for equipment use. Descriptive study outcomes indicated ease of program use, strong satisfaction with learning and appreciation of program accessibility. Additionally, four studies reported significant improvements in knowledge post-intervention. Web-based simulation is highly acceptable to students and appears to provide learning benefits that align with other simulation approaches and it augments face-to-face teaching. Web-based simulation is likely to have a major place in nursing curricula in the next decade, yet further research is necessary to objectively evaluate learner outcomes and to justify its use. Copyright © 2014 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCoy, Michel; Archer, Bill; Hendrickson, Bruce

The Stockpile Stewardship Program (SSP) is an integrated technical program for maintaining the safety, surety, and reliability of the U.S. nuclear stockpile. The SSP uses nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of experimental facilities and programs, and the computational capabilities to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computationalmore » resources that support annual stockpile assessment and certification, study advanced nuclear weapons design and manufacturing processes, analyze accident scenarios and weapons aging, and provide the tools to enable stockpile Life Extension Programs (LEPs) and the resolution of Significant Finding Investigations (SFIs). This requires a balance of resource, including technical staff, hardware, simulation software, and computer science solutions. ASC is now focused on increasing predictive capabilities in a three-dimensional (3D) simulation environment while maintaining support to the SSP. The program continues to improve its unique tools for solving progressively more difficult stockpile problems (sufficient resolution, dimensionality, and scientific details), and quantifying critical margins and uncertainties. Resolving each issue requires increasingly difficult analyses because the aging process has progressively moved the stockpile further away from the original test base. Where possible, the program also enables the use of high performance computing (HPC) and simulation tools to address broader national security needs, such as foreign nuclear weapon assessments and counter nuclear terrorism.« less

The Effectiveness of Simulated Robots for Supporting the Learning of Introductory Programming: A Multi-Case Case Study

ERIC Educational Resources Information Center

Major, Louis; Kyriacou, Theocharis; Brereton, Pearl

2014-01-01

This work investigates the effectiveness of simulated robots as tools to support the learning of programming. After the completion of a systematic review and exploratory research, a multi-case case study was undertaken. A simulator, named Kebot, was developed and used to run four 10-hour programming workshops. Twenty-three student participants…

Development of a task-level robot programming and simulation system

NASA Technical Reports Server (NTRS)

Liu, H.; Kawamura, K.; Narayanan, S.; Zhang, G.; Franke, H.; Ozkan, M.; Arima, H.; Liu, H.

1987-01-01

An ongoing project in developing a Task-Level Robot Programming and Simulation System (TARPS) is discussed. The objective of this approach is to design a generic TARPS that can be used in a variety of applications. Many robotic applications require off-line programming, and a TARPS is very useful in such applications. Task level programming is object centered in that the user specifies tasks to be performed instead of robot paths. Graphics simulation provides greater flexibility and also avoids costly machine setup and possible damage. A TARPS has three major modules: world model, task planner and task simulator. The system architecture, design issues and some preliminary results are given.

Electric-car simulation

NASA Technical Reports Server (NTRS)

Chapman, C. P.; Slusser, R. A.

1980-01-01

PARAMET, interactive simulation program for parametric studies of electric vehicles, guides user through simulation by menu and series of prompts for input parameters. Program considers aerodynamic drag, rolling resistance, linear and rotational acceleration, and road gradient as forces acting on vehicle.

A National Survey on Teaching and Assessing Technical Proficiency in Vascular Surgery in Canada.

PubMed

Drudi, Laura; Hossain, Sajjid; Mackenzie, Kent S; Corriveau, Marc-Michel; Abraham, Cherrie Z; Obrand, Daniel I; Vassiliou, Melina; Gill, Heather; Steinmetz, Oren K

2016-05-01

This survey aims to explore trainees' perspectives on how Canadian vascular surgery training programs are using simulation in teaching and assessing technical skills through a cross-sectional national survey. A 10-min online questionnaire was sent to Program Directors of Canada's Royal College of Physicians and Surgeons' of Canada approved training programs in vascular surgery. This survey was distributed among residents and fellows who were studying in the 2013-2014 academic year. Twenty-eight (58%) of the 48 Canadian vascular surgery trainees completed the survey. A total of 68% of the respondents were part of the 0 + 5 integrated vascular surgery training program. The use of simulation in the assessment of technical skills at the beginning of training was reported by only 3 (11%) respondents, whereas 43% reported that simulation was used in their programs in the assessment of technical skills at some time during their training. Training programs most often provided simulation as a method of teaching and learning endovascular abdominal aortic or thoracic aneurysm repair (64%). Furthermore, 96% of trainees reported the most common resource to learn and enhance technical skills was dialog with vascular surgery staff. Surveyed vascular surgery trainees in Canada report that simulation is rarely used as a tool to assess baseline technical skills at the beginning of training. Less than half of surveyed trainees in vascular surgery programs in Canada report that simulation is being used for skills acquisition. Currently, in Canadian training programs, simulation is most commonly used to teach endovascular skills. Copyright © 2016 Elsevier Inc. All rights reserved.

A mathematical model for Vertical Attitude Takeoff and Landing (VATOL) aircraft simulation. Volume 3: User's manual for VATOL simulation program

NASA Technical Reports Server (NTRS)

Fortenbaugh, R. L.

1980-01-01

Instructions for using Vertical Attitude Takeoff and Landing Aircraft Simulation (VATLAS), the digital simulation program for application to vertical attitude takeoff and landing (VATOL) aircraft developed for installation on the NASA Ames CDC 7600 computer system are described. The framework for VATLAS is the Off-Line Simulation (OLSIM) routine. The OLSIM routine provides a flexible framework and standardized modules which facilitate the development of off-line aircraft simulations. OLSIM runs under the control of VTOLTH, the main program, which calls the proper modules for executing user specified options. These options include trim, stability derivative calculation, time history generation, and various input-output options.

No Vent Tank Fill and Transfer Line Chilldown Analysis by Generalized Fluid System Simulation Program (GFSSP)

NASA Technical Reports Server (NTRS)

Majumdar, Alok

2013-01-01

The purpose of the paper is to present the analytical capability developed to model no vent chill and fill of cryogenic tank to support CPST (Cryogenic Propellant Storage and Transfer) program. Generalized Fluid System Simulation Program (GFSSP) was adapted to simulate charge-holdvent method of Tank Chilldown. GFSSP models were developed to simulate chilldown of LH2 tank in K-site Test Facility and numerical predictions were compared with test data. The report also describes the modeling technique of simulating the chilldown of a cryogenic transfer line and GFSSP models were developed to simulate the chilldown of a long transfer line and compared with test data.

Generalized environmental control and life support system computer program (G1894), phase 3

NASA Technical Reports Server (NTRS)

Mcenulty, R. E.

1978-01-01

The work performed during Phase 3 of the Generalized Environmental Control Life Support System (ECLSS) Computer Program is reported. Phase 3 of this program covered the period from December 1977 to September 1978. The computerized simulation of the Shuttle Orbiter ECLSS was upgraded in the following areas: (1) the payload loop of the Shuttle simulation was completely recoded and checked out; (2) the Shuttle simulation water and freon loop initialization logic was simplified to permit easier program input for the user; (3) the computerized simulation was modified to accept the WASP subroutine, which is a subroutine to evaluate thermal properties of water and freon; (4) the 1108 operating system was upgraded by LEC; (5) the Shuttle simulation was modified to permit failure cases which simulate zero component flow values; and (6) the Shuttle SEPS version was modified and secure files were setup on the 1108 and 1110 systems to permit simulation runs to be made from remote terminals.

A Monte-Carlo maplet for the study of the optical properties of biological tissues

NASA Astrophysics Data System (ADS)

Yip, Man Ho; Carvalho, M. J.

2007-12-01

Monte-Carlo simulations are commonly used to study complex physical processes in various fields of physics. In this paper we present a Maple program intended for Monte-Carlo simulations of photon transport in biological tissues. The program has been designed so that the input data and output display can be handled by a maplet (an easy and user-friendly graphical interface), named the MonteCarloMaplet. A thorough explanation of the programming steps and how to use the maplet is given. Results obtained with the Maple program are compared with corresponding results available in the literature. Program summaryProgram title:MonteCarloMaplet Catalogue identifier:ADZU_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADZU_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.:3251 No. of bytes in distributed program, including test data, etc.:296 465 Distribution format: tar.gz Programming language:Maple 10 Computer: Acer Aspire 5610 (any running Maple 10) Operating system: Windows XP professional (any running Maple 10) Classification: 3.1, 5 Nature of problem: Simulate the transport of radiation in biological tissues. Solution method: The Maple program follows the steps of the C program of L. Wang et al. [L. Wang, S.L. Jacques, L. Zheng, Computer Methods and Programs in Biomedicine 47 (1995) 131-146]; The Maple library routine for random number generation is used [Maple 10 User Manual c Maplesoft, a division of Waterloo Maple Inc., 2005]. Restrictions: Running time increases rapidly with the number of photons used in the simulation. Unusual features: A maplet (graphical user interface) has been programmed for data input and output. Note that the Monte-Carlo simulation was programmed with Maple 10. If attempting to run the simulation with an earlier version of Maple, appropriate modifications (regarding typesetting fonts) are required and once effected the worksheet runs without problem. However some of the windows of the maplet may still appear distorted. Running time: Depends essentially on the number of photons used in the simulation. Elapsed times for particular runs are reported in the main text.

Investigation of roughing machining simulation by using visual basic programming in NX CAM system

NASA Astrophysics Data System (ADS)

Hafiz Mohamad, Mohamad; Nafis Osman Zahid, Muhammed

2018-03-01

This paper outlines a simulation study to investigate the characteristic of roughing machining simulation in 4th axis milling processes by utilizing visual basic programming in NX CAM systems. The selection and optimization of cutting orientation in rough milling operation is critical in 4th axis machining. The main purpose of roughing operation is to approximately shape the machined parts into finished form by removing the bulk of material from workpieces. In this paper, the simulations are executed by manipulating a set of different cutting orientation to generate estimated volume removed from the machine parts. The cutting orientation with high volume removal is denoted as an optimum value and chosen to execute a roughing operation. In order to run the simulation, customized software is developed to assist the routines. Operations build-up instructions in NX CAM interface are translated into programming codes via advanced tool available in the Visual Basic Studio. The codes is customized and equipped with decision making tools to run and control the simulations. It permits the integration with any independent program files to execute specific operations. This paper aims to discuss about the simulation program and identifies optimum cutting orientations for roughing processes. The output of this study will broaden up the simulation routines performed in NX CAM systems.

Alexander Meets Michotte: A Simulation Tool Based on Pattern Programming and Phenomenology

ERIC Educational Resources Information Center

Basawapatna, Ashok

2016-01-01

Simulation and modeling activities, a key point of computational thinking, are currently not being integrated into the science classroom. This paper describes a new visual programming tool entitled the Simulation Creation Toolkit. The Simulation Creation Toolkit is a high level pattern-based phenomenological approach to bringing rapid simulation…

Water Quality Assessment Simulation Program (WASP8): Upgrades to the Advanced Toxicant Module for Simulating Dissolved Chemicals, Nanomaterials, and Solids

EPA Science Inventory

The Water Quality Analysis Simulation Program (WASP) is a dynamic, spatially-resolved, differential mass balance fate and transport modeling framework. WASP is used to develop models to simulate concentrations of environmental contaminants in surface waters and sediments. As a mo...

Meaningful Use of Simulation as an Educational Method in Nursing Programs

ERIC Educational Resources Information Center

Thompson, Teri L.

2011-01-01

The purpose of this descriptive study was to examine the use of simulation technology within nursing programs leading to licensure as registered nurses. In preparation for this study the Use of Simulation Technology Inventory (USTI) was developed and based in the structure, processes, outcomes model and the current literature on simulation. The…

VEEP - Vehicle Economy, Emissions, and Performance program

NASA Technical Reports Server (NTRS)

Heimburger, D. A.; Metcalfe, M. A.

1977-01-01

VEEP is a general-purpose discrete event simulation program being developed to study the performance, fuel economy, and exhaust emissions of a vehicle modeled as a collection of its separate components. It is written in SIMSCRIPT II.5. The purpose of this paper is to present the design methodology, describe the simulation model and its components, and summarize the preliminary results. Topics include chief programmer team concepts, the SDDL design language, program portability, user-oriented design, the program's user command syntax, the simulation procedure, and model validation.

A computer program for estimating the power-density spectrum of advanced continuous simulation language generated time histories

NASA Technical Reports Server (NTRS)

Dunn, H. J.

1981-01-01

A computer program for performing frequency analysis of time history data is presented. The program uses circular convolution and the fast Fourier transform to calculate power density spectrum (PDS) of time history data. The program interfaces with the advanced continuous simulation language (ACSL) so that a frequency analysis may be performed on ACSL generated simulation variables. An example of the calculation of the PDS of a Van de Pol oscillator is presented.

Generalized dynamic engine simulation techniques for the digital computer

NASA Technical Reports Server (NTRS)

Sellers, J.; Teren, F.

1974-01-01

Recently advanced simulation techniques have been developed for the digital computer and used as the basis for development of a generalized dynamic engine simulation computer program, called DYNGEN. This computer program can analyze the steady state and dynamic performance of many kinds of aircraft gas turbine engines. Without changes to the basic program, DYNGEN can analyze one- or two-spool turbofan engines. The user must supply appropriate component performance maps and design-point information. Examples are presented to illustrate the capabilities of DYNGEN in the steady state and dynamic modes of operation. The analytical techniques used in DYNGEN are briefly discussed, and its accuracy is compared with a comparable simulation using the hybrid computer. The impact of DYNGEN and similar all-digital programs on future engine simulation philosophy is also discussed.

Generalized dynamic engine simulation techniques for the digital computer

NASA Technical Reports Server (NTRS)

Sellers, J.; Teren, F.

1974-01-01

Recently advanced simulation techniques have been developed for the digital computer and used as the basis for development of a generalized dynamic engine simulation computer program, called DYNGEN. This computer program can analyze the steady state and dynamic performance of many kinds of aircraft gas turbine engines. Without changes to the basic program DYNGEN can analyze one- or two-spool turbofan engines. The user must supply appropriate component performance maps and design-point information. Examples are presented to illustrate the capabilities of DYNGEN in the steady state and dynamic modes of operation. The analytical techniques used in DYNGEN are briefly discussed, and its accuracy is compared with a comparable simulation using the hybrid computer. The impact of DYNGEN and similar all-digital programs on future engine simulation philosophy is also discussed.

Generalized dynamic engine simulation techniques for the digital computers

NASA Technical Reports Server (NTRS)

Sellers, J.; Teren, F.

1975-01-01

Recently advanced simulation techniques have been developed for the digital computer and used as the basis for development of a generalized dynamic engine simulation computer program, called DYNGEN. This computer program can analyze the steady state and dynamic performance of many kinds of aircraft gas turbine engines. Without changes to the basic program, DYNGEN can analyze one- or two-spool turbofan engines. The user must supply appropriate component performance maps and design point information. Examples are presented to illustrate the capabilities of DYNGEN in the steady state and dynamic modes of operation. The analytical techniques used in DYNGEN are briefly discussed, and its accuracy is compared with a comparable simulation using the hybrid computer. The impact of DYNGEN and similar digital programs on future engine simulation philosophy is also discussed.

Obstetric team simulation program challenges.

PubMed

Bullough, A S; Wagner, S; Boland, T; Waters, T P; Kim, K; Adams, W

2016-12-01

To describe the challenges associated with the development and assessment of an obstetric emergency team simulation program. The goal was to develop a hybrid, in-situ and high fidelity obstetric emergency team simulation program that incorporated weekly simulation sessions on the labor and delivery unit, and quarterly, education protected sessions in the simulation center. All simulation sessions were video-recorded and reviewed. Labor and delivery unit and simulation center. Medical staff covering labor and delivery, anesthesiology and obstetric residents and obstetric nurses. Assessments included an on-line knowledge multiple-choice questionnaire about the simulation scenarios. This was completed prior to the initial in-situ simulation session and repeated 3 months later, the Clinical Teamwork Scale with inter-rater reliability, participant confidence surveys and subjective participant satisfaction. A web-based curriculum comprising modules on communication skills, team challenges, and team obstetric emergency scenarios was also developed. Over 4 months, only 6 labor and delivery unit in-situ sessions out of a possible 14 sessions were carried out. Four high-fidelity sessions were performed in 2 quarterly education protected meetings in the simulation center. Information technology difficulties led to the completion of only 18 pre/post web-based multiple-choice questionnaires. These test results showed no significant improvement in raw score performance from pre-test to post-test (P=.27). During Clinical Teamwork Scale live and video assessment, trained raters and program faculty were in agreement only 31% and 28% of the time, respectively (Kendall's W=.31, P<.001 and W=.28, P<.001). Participant confidence surveys overall revealed confidence significantly increased (P<.05), from pre-scenario briefing to after post-scenario debriefing. Program feedback indicates a high level of participant satisfaction and improved confidence yet further program refinement is required. Copyright © 2016 Elsevier Inc. All rights reserved.

A finite-element model for simulation of two-dimensional steady-state ground-water flow in confined aquifers

USGS Publications Warehouse

Kuniansky, E.L.

1990-01-01

A computer program based on the Galerkin finite-element method was developed to simulate two-dimensional steady-state ground-water flow in either isotropic or anisotropic confined aquifers. The program may also be used for unconfined aquifers of constant saturated thickness. Constant head, constant flux, and head-dependent flux boundary conditions can be specified in order to approximate a variety of natural conditions, such as a river or lake boundary, and pumping well. The computer program was developed for the preliminary simulation of ground-water flow in the Edwards-Trinity Regional aquifer system as part of the Regional Aquifer-Systems Analysis Program. Results of the program compare well to analytical solutions and simulations .from published finite-difference models. A concise discussion of the Galerkin method is presented along with a description of the program. Provided in the Supplemental Data section are a listing of the computer program, definitions of selected program variables, and several examples of data input and output used in verifying the accuracy of the program.

Low-thrust solar electric propulsion navigation simulation program

NASA Technical Reports Server (NTRS)

Hagar, H. J.; Eller, T. J.

1973-01-01

An interplanetary low-thrust, solar electric propulsion mission simulation program suitable for navigation studies is presented. The mathematical models for trajectory simulation, error compensation, and tracking motion are described. The languages, input-output procedures, and subroutines are included.

International collaborative faculty development program on simulation-based healthcare education: a report on its successes and challenges.

PubMed

Chung, Hyun Soo; Issenberg, S Barry; Phrampus, Paul; Miller, Geoff; Je, Sang Mo; Lim, Tae Ho; Kim, Young Min

2012-12-01

Countries that are less experienced with simulation-based healthcare education (SBHE) often import Western programs to initiate their efforts to deliver effective simulation training. Acknowledging cultural differences, we sought to determine whether faculty development program on SBHE in the United States could be transported successfully to train faculty members in Korea. An international, collaborative, multi-professional program from a pre-existing Western model was adapted. The process focused on prioritization of curricular elements based on local needs, translation of course materials, and delivery of the program in small group facilitation exercises. Three types of evaluation data were collected: participants' simulation experience; participants' ratings of the course; and participant's self-assessment of the impact of the course on their knowledge, skills, and attitudes (KSA) toward simulation teaching. Thirty faculty teachers participated in the course. Eighty percent of the participants answered that they spent less than 25% of their time as simulation instructors. Time spent on planning, scenario development, delivering training, research, and administrative work ranged from 10% to 30%. Twenty-eight of 30 participants agreed or strongly agreed that the course was excellent and relevant to their needs. The participants' assessment of the impact of the course on their KSA toward simulation teaching improved significantly. Although there were many challenges to overcome, a systematic approach in the adaptation of a Western simulation faculty development course model was successfully implemented in Korea, and the program improves self-confidence and learning in participants.

Conducting Simulation Studies in the R Programming Environment.

PubMed

Hallgren, Kevin A

2013-10-12

Simulation studies allow researchers to answer specific questions about data analysis, statistical power, and best-practices for obtaining accurate results in empirical research. Despite the benefits that simulation research can provide, many researchers are unfamiliar with available tools for conducting their own simulation studies. The use of simulation studies need not be restricted to researchers with advanced skills in statistics and computer programming, and such methods can be implemented by researchers with a variety of abilities and interests. The present paper provides an introduction to methods used for running simulation studies using the R statistical programming environment and is written for individuals with minimal experience running simulation studies or using R. The paper describes the rationale and benefits of using simulations and introduces R functions relevant for many simulation studies. Three examples illustrate different applications for simulation studies, including (a) the use of simulations to answer a novel question about statistical analysis, (b) the use of simulations to estimate statistical power, and (c) the use of simulations to obtain confidence intervals of parameter estimates through bootstrapping. Results and fully annotated syntax from these examples are provided.

A trial of e-simulation of sudden patient deterioration (FIRST2ACT WEB) on student learning.

PubMed

Bogossian, Fiona E; Cooper, Simon J; Cant, Robyn; Porter, Joanne; Forbes, Helen

2015-10-01

High-fidelity simulation pedagogy is of increasing importance in health professional education; however, face-to-face simulation programs are resource intensive and impractical to implement across large numbers of students. To investigate undergraduate nursing students' theoretical and applied learning in response to the e-simulation program-FIRST2ACT WEBTM, and explore predictors of virtual clinical performance. Multi-center trial of FIRST2ACT WEBTM accessible to students in five Australian universities and colleges, across 8 campuses. A population of 489 final-year nursing students in programs of study leading to license to practice. Participants proceeded through three phases: (i) pre-simulation-briefing and assessment of clinical knowledge and experience; (ii) e-simulation-three interactive e-simulation clinical scenarios which included video recordings of patients with deteriorating conditions, interactive clinical tasks, pop up responses to tasks, and timed performance; and (iii) post-simulation feedback and evaluation. Descriptive statistics were followed by bivariate analysis to detect any associations, which were further tested using standard regression analysis. Of 409 students who commenced the program (83% response rate), 367 undergraduate nursing students completed the web-based program in its entirety, yielding a completion rate of 89.7%; 38.1% of students achieved passing clinical performance across three scenarios, and the proportion achieving passing clinical knowledge increased from 78.15% pre-simulation to 91.6% post-simulation. Knowledge was the main independent predictor of clinical performance in responding to a virtual deteriorating patient R(2)=0.090, F(7, 352)=4.962, p<0.001. The use of web-based technology allows simulation activities to be accessible to a large number of participants and completion rates indicate that 'Net Generation' nursing students were highly engaged with this mode of learning. The web-based e-simulation program FIRST2ACTTM effectively enhanced knowledge, virtual clinical performance, and self-assessed knowledge, skills, confidence, and competence in final-year nursing students. Copyright © 2015 Elsevier Ltd. All rights reserved.

Simulation For Task Practice in Technical Training.

ERIC Educational Resources Information Center

Mallory, W. J.

1981-01-01

Describes two programs used by the Ford Motor Company to train manufacturing skilled trades personnel. Programmable Controller Maintenance Training Program for Industrial Technicians and Troubleshooting Strategy Program use simulation and provide improved task performance after training. (JOW)

Software Maintenance of the Subway Environment Simulation Computer Program

DOT National Transportation Integrated Search

1980-12-01

This document summarizes the software maintenance activities performed to support the Subway Environment Simulation (SES) Computer Program. The SES computer program is a design-oriented analytic tool developed during a recent five-year research proje...

A Guide for the Management of Special Education Programs. 3.0 Educational Simulations. Newday Operations Guide for Drug Dependent Minor Programs.

ERIC Educational Resources Information Center

Santa Cruz County Superintendent of Schools, CA.

Presented is the third component, Educational Simulations, of a special day class educational program for drug dependent minors. One objective of the project is said to have been the identification of instructional methods and materials suited to drug dependent minors. Educational games and simulations designed to provide practice in reading and…

Design of a CO2 Twin Rotary Compressor for a Heat Pump Water Heater

NASA Astrophysics Data System (ADS)

Ahn, Jong Min; Kim, Woo Young; Kim, Hyun Jin; Cho, Sung Oug; Seo, Jong Cheun

2010-06-01

For a CO2 heat pump water heater, one-stage twin rotary compressor has been designed. As a design tool, computer simulation program for the compressor performance has been made. Validation of the simulation program has been carried out for a bench model compressor in a compressor calorimeter. Cooling capacity and the compressor input power were reasonably well compared between the simulation and the calorimeter test. Good agreement on P-V diagram between the simulation and the test was also obtained. With this validated compressor simulation program, parametric study has been performed to arrive at optimum dimensions for the compression chamber.

USERS MANUAL FOR HYDROLOGICAL SIMULATION PROGRAM - FORTRAN (HSPF)

EPA Science Inventory

The Hydrological Simulation Program--Fortran (HSPF) is a set of computer codes that can simulate the hydrologic, and associated water quality, processes on pervious and impervious land surfaces and in streams and well-mixed impoundments. The manual discusses the modular structure...

Construction of dynamic stochastic simulation models using knowledge-based techniques

NASA Technical Reports Server (NTRS)

Williams, M. Douglas; Shiva, Sajjan G.

1990-01-01

Over the past three decades, computer-based simulation models have proven themselves to be cost-effective alternatives to the more structured deterministic methods of systems analysis. During this time, many techniques, tools and languages for constructing computer-based simulation models have been developed. More recently, advances in knowledge-based system technology have led many researchers to note the similarities between knowledge-based programming and simulation technologies and to investigate the potential application of knowledge-based programming techniques to simulation modeling. The integration of conventional simulation techniques with knowledge-based programming techniques is discussed to provide a development environment for constructing knowledge-based simulation models. A comparison of the techniques used in the construction of dynamic stochastic simulation models and those used in the construction of knowledge-based systems provides the requirements for the environment. This leads to the design and implementation of a knowledge-based simulation development environment. These techniques were used in the construction of several knowledge-based simulation models including the Advanced Launch System Model (ALSYM).

Easy GROMACS: A Graphical User Interface for GROMACS Molecular Dynamics Simulation Package

NASA Astrophysics Data System (ADS)

Dizkirici, Ayten; Tekpinar, Mustafa

2015-03-01

GROMACS is a widely used molecular dynamics simulation package. Since it is a command driven program, it is difficult to use this program for molecular biologists, biochemists, new graduate students and undergraduate researchers who are interested in molecular dynamics simulations. To alleviate the problem for those researchers, we wrote a graphical user interface that simplifies protein preparation for a classical molecular dynamics simulation. Our program can work with various GROMACS versions and it can perform essential analyses of GROMACS trajectories as well as protein preparation. We named our open source program `Easy GROMACS'. Easy GROMACS can give researchers more time for scientific research instead of dealing with technical intricacies.

Visualizing ultrasound through computational modeling

NASA Technical Reports Server (NTRS)

Guo, Theresa W.

2004-01-01

The Doppler Ultrasound Hematocrit Project (DHP) hopes to find non-invasive methods of determining a person s blood characteristics. Because of the limits of microgravity and the space travel environment, it is important to find non-invasive methods of evaluating the health of persons in space. Presently, there is no well developed method of determining blood composition non-invasively. This projects hopes to use ultrasound and Doppler signals to evaluate the characteristic of hematocrit, the percentage by volume of red blood cells within whole blood. These non-invasive techniques may also be developed to be used on earth for trauma patients where invasive measure might be detrimental. Computational modeling is a useful tool for collecting preliminary information and predictions for the laboratory research. We hope to find and develop a computer program that will be able to simulate the ultrasound signals the project will work with. Simulated models of test conditions will more easily show what might be expected from laboratory results thus help the research group make informed decisions before and during experimentation. There are several existing Matlab based computer programs available, designed to interpret and simulate ultrasound signals. These programs will be evaluated to find which is best suited for the project needs. The criteria of evaluation that will be used are 1) the program must be able to specify transducer properties and specify transmitting and receiving signals, 2) the program must be able to simulate ultrasound signals through different attenuating mediums, 3) the program must be able to process moving targets in order to simulate the Doppler effects that are associated with blood flow, 4) the program should be user friendly and adaptable to various models. After a computer program is chosen, two simulation models will be constructed. These models will simulate and interpret an RF data signal and a Doppler signal.

Simulated Consulting Experiences in Counselor Preparation

ERIC Educational Resources Information Center

Panther, Edward E.

1971-01-01

Simulation, using role playing and commercially available materials, was used to provide counselor teacher consultation experience for counselor trainees. The results of the program supported the use of simulation as a technique for counselor education. Implications for counselor education programs are discussed. (Author/CG)

Feasibility Study On Missile Launch Detection And Trajectory Tracking

DTIC Science & Technology

2016-09-01

Vehicles ( UAVs ) in military operations, their role in a missile defense operation is not well defined. The simulation program discussed in this thesis ...targeting information to an attacking UAV to reliably intercept the missile. B . FURTHER STUDIES The simulation program can be enhanced to improve the...intercept the threat. This thesis explores the challenges in creating a simulation program to process video footage from an unstable platform and the

Toward XML Representation of NSS Simulation Scenario for Mission Scenario Exchange Capability

DTIC Science & Technology

2003-09-01

app.html Deitel , H. M., Deitel , P. J., Nieto, T. R., Lin, T. M., Sadhu, P. (2001). XML How to Program . Upper Saddle River: Prentice Hall...Combat XXI Program ...........................13 2. Transition NSS to a Java Environment ...........................................13 3. Shift to an...STATEMENT The Naval Simulation System (NSS) is a powerful computer program developed by the Navy to provide a force-on-force modeling and simulation

An analysis of the 70-meter antenna hydrostatic bearing by means of computer simulation

NASA Technical Reports Server (NTRS)

Bartos, R. D.

1993-01-01

Recently, the computer program 'A Computer Solution for Hydrostatic Bearings with Variable Film Thickness,' used to design the hydrostatic bearing of the 70-meter antennas, was modified to improve the accuracy with which the program predicts the film height profile and oil pressure distribution between the hydrostatic bearing pad and the runner. This article presents a description of the modified computer program, the theory upon which the computer program computations are based, computer simulation results, and a discussion of the computer simulation results.

Evaluation of Rankine cycle air conditioning system hardware by computer simulation

NASA Technical Reports Server (NTRS)

Healey, H. M.; Clark, D.

1978-01-01

A computer program for simulating the performance of a variety of solar powered Rankine cycle air conditioning system components (RCACS) has been developed. The computer program models actual equipment by developing performance maps from manufacturers data and is capable of simulating off-design operation of the RCACS components. The program designed to be a subroutine of the Marshall Space Flight Center (MSFC) Solar Energy System Analysis Computer Program 'SOLRAD', is a complete package suitable for use by an occasional computer user in developing performance maps of heating, ventilation and air conditioning components.

In situ pediatric trauma simulation: assessing the impact and feasibility of an interdisciplinary pediatric in situ trauma care quality improvement simulation program.

PubMed

Auerbach, Marc; Roney, Linda; Aysseh, April; Gawel, Marcie; Koziel, Jeannette; Barre, Kimberly; Caty, Michael G; Santucci, Karen

2014-12-01

This study aimed to evaluate the feasibility and measure the impact of an in situ interdisciplinary pediatric trauma quality improvement simulation program. Twenty-two monthly simulations were conducted in a tertiary care pediatric emergency department with the aim of improving the quality of pediatric trauma (February 2010 to November 2012). Each session included 20 minutes of simulated patient care, followed by 30 minutes of debriefing that focused on teamwork, communication, and the identification of gaps in care. A single rater scored the performance of the team in real time using a validated assessment instrument for 6 subcomponents of care (teamwork, airway, intubation, breathing, circulation, and disability). Participants completed a survey and written feedback forms. A trend analysis of the 22 simulations found statistically significant positive trends for overall performance, teamwork, and intubation subcomponents; the strength of the upward trend was the strongest for the teamwork (τ = 0.512), followed by overall performance (τ = 0.488) and intubation (τ = 0.433). Two hundred fifty-one of 398 participants completed the participant feedback form (response rate, 63%), reporting that debriefing was the most valuable aspect of the simulation. An in situ interdisciplinary pediatric trauma simulation quality improvement program resulted in improved validated trauma simulation assessment scores for overall performance, teamwork, and intubation. Participants reported high levels of satisfaction with the program, and debriefing was reported as the most valuable component of the program.

Effectiveness evaluation of STOL transport operations (phase 2). [computer simulation program of commercial short haul aircraft operations

NASA Technical Reports Server (NTRS)

Welp, D. W.; Brown, R. A.; Ullman, D. G.; Kuhner, M. B.

1974-01-01

A computer simulation program which models a commercial short-haul aircraft operating in the civil air system was developed. The purpose of the program is to evaluate the effect of a given aircraft avionics capability on the ability of the aircraft to perform on-time carrier operations. The program outputs consist primarily of those quantities which can be used to determine direct operating costs. These include: (1) schedule reliability or delays, (2) repairs/replacements, (3) fuel consumption, and (4) cancellations. More comprehensive models of the terminal area environment were added and a simulation of an existing airline operation was conducted to obtain a form of model verification. The capability of the program to provide comparative results (sensitivity analysis) was then demonstrated by modifying the aircraft avionics capability for additional computer simulations.

Crew station research and development facility training for the light helicopter demonstration/validation program

NASA Technical Reports Server (NTRS)

Matsumoto, Joy Hamerman; Rogers, Steven; Mccauley, Michael; Salinas, AL

1992-01-01

The U.S. Army Crew Station Research and Development Branch (CSRDB) of the Aircraft Simulation Division (AVSCOM) was tasked by the Light Helicopter Program Manager (LH-PM) to provide training to Army personnel in advanced aircraft simulation technology. The purpose of this training was to prepare different groups of pilots to support and evaluate two contractor simulation efforts during the Demonstration/Validation (DEM/VAL) phase of the LH program. The personnel in the CSRDB developed mission oriented training programs to accomplish the objectives, conduct the programs, and provide guidance to army personnel and support personnel throughout the DEM/VAL phase.

Easing student transition to graduate nurse: a SIMulated Professional Learning Environment (SIMPLE) for final year student nurses.

PubMed

Liaw, Sok Ying; Koh, Yiwen; Dawood, Rabiah; Kowitlawakul, Yanika; Zhou, Wentao; Lau, Siew Tiang

2014-03-01

Preparing nursing students for making the transition to graduate nurse is crucial for entry into practice. Final year student nurses at the National University of Singapore (NUS) are required to undergo a consolidated clinical practice to prepare them for their transition to graduate nurse. To describe the development, implementation and evaluation of a simulation program known as SIMulated Professional Learning Environment (SIMPLE) in preparing the final year student nurses for their clinical practicum in transition to graduate nurse practice. A set of simulation features and best practices were used as conceptual framework to develop and implement the simulation program. 94 final year student nurses participated in the 15-hour SIMPLE program that incorporated multiple simulation scenarios based on actual ward clinical practices. Pre and post-tests were conducted to assess the students' preparedness for their clinical practice in transition to graduate nurse practice. The students also completed a satisfaction questionnaire and open questions to evaluate their simulation experiences. The student nurses demonstrated a significant improvement (t=12.06, p<0.01) on post-test score (mean=117.21, SD=15.17) from pre-test score (mean=97.86, SD=15.08) for their perceived preparedness towards their clinical practicum in transition to graduate nurse practice. They were highly satisfied with their simulation learning. Themes emerged from the comments on the most valuable aspects of the SIMPLE program and ways to improve the program. The study provided evidences on the effectiveness of the SIMPLE program in enhancing the students' preparedness for their transition to graduate nurse practice. A key success of the SIMPLE program was the used of simulation strategy and the involvement of practicing nurses that closely linked the students with the realities of current nursing practice to prepare them for the role of staff nurses. Copyright © 2013 Elsevier Ltd. All rights reserved.

Winning the Energy Game.

ERIC Educational Resources Information Center

Zielinski, Edward J.; Bethel, Lowell J.

1983-01-01

Describes the use of an Energy-Environment Simulator in environmental/energy education programs. The simulator is a specially designed analog computer that simulates real-world conditions of energy production and use. Energy resources, demands, and the environmental effects of energy use are programmed into the computer. (Author/JN)

HYDROLOGICAL SIMULATION PROGRAM-FORTRAN (HSPF): USERS MANUAL FOR RELEASE 8.0

EPA Science Inventory

The Hydrological Simulation Program--FORTRAN (HSPF) is a set of computer codes that can simulate the hydrologic, and associated water quality, processes on pervious and impervious land surfaces and in streams and well mixed impoundments. The manual discusses the modular structure...

Object-oriented approach for gas turbine engine simulation

NASA Technical Reports Server (NTRS)

Curlett, Brian P.; Felder, James L.

1995-01-01

An object-oriented gas turbine engine simulation program was developed. This program is a prototype for a more complete, commercial grade engine performance program now being proposed as part of the Numerical Propulsion System Simulator (NPSS). This report discusses architectural issues of this complex software system and the lessons learned from developing the prototype code. The prototype code is a fully functional, general purpose engine simulation program, however, only the component models necessary to model a transient compressor test rig have been written. The production system will be capable of steady state and transient modeling of almost any turbine engine configuration. Chief among the architectural considerations for this code was the framework in which the various software modules will interact. These modules include the equation solver, simulation code, data model, event handler, and user interface. Also documented in this report is the component based design of the simulation module and the inter-component communication paradigm. Object class hierarchies for some of the code modules are given.

Development and Application of a Computer Simulation Program to Enhance the Clinical Problem-Solving Skills of Students.

ERIC Educational Resources Information Center

Boh, Larry E.; And Others

1987-01-01

A project to (1) develop and apply a microcomputer simulation program to enhance clinical medication problem solving in preclerkship and clerkship students and (2) perform an initial formative evaluation of the simulation is described. A systematic instructional design approach was used in applying the simulation to the disease state of rheumatoid…

Documentation of the Benson Diesel Engine Simulation Program

NASA Technical Reports Server (NTRS)

Vangerpen, Jon

1988-01-01

This report documents the Benson Diesel Engine Simulation Program and explains how it can be used to predict the performance of diesel engines. The program was obtained from the Garrett Turbine Engine Company but has been extensively modified since. The program is a thermodynamic simulation of the diesel engine cycle which uses a single zone combustion model. It can be used to predict the effect of changes in engine design and operating parameters such as valve timing, speed and boost pressure. The most significan change made to this program is the addition of a more detailed heat transfer model to predict metal part temperatures. This report contains a description of the sub-models used in the Benson program, a description of the input parameters and sample program runs.

An adaptive maneuvering logic computer program for the simulation of one-to-one air-to-air combat. Volume 2: Program description

NASA Technical Reports Server (NTRS)

Burgin, G. H.; Owens, A. J.

1975-01-01

A detailed description is presented of the computer programs in order to provide an understanding of the mathematical and geometrical relationships as implemented in the programs. The individual sbbroutines and their underlying mathematical relationships are described, and the required input data and the output provided by the program are explained. The relationship of the adaptive maneuvering logic program with the program to drive the differential maneuvering simulator is discussed.

Comparison of Building Loads Analysis and System Thermodynamics (BLAST) Computer Program Simulations and Measured Energy Use for Army Buildings.

DTIC Science & Technology

1980-05-01

engineering ,ZteNo D R RPTE16 research w 9 laboratory COMPARISON OF BUILDING LOADS ANALYSIS AND SYSTEM THERMODYNAMICS (BLAST) AD 0 5 5,0 3COMPUTER PROGRAM...Building Loads Analysis and System Thermodynamics (BLAST) computer program. A dental clinic and a battalion headquarters and classroom building were...Building and HVAC System Data Computer Simulation Comparison of Actual and Simulated Results ANALYSIS AND FINDINGS

MySSP: Non-stationary evolutionary sequence simulation, including indels

PubMed Central

Rosenberg, Michael S.

2007-01-01

MySSP is a new program for the simulation of DNA sequence evolution across a phylogenetic tree. Although many programs are available for sequence simulation, MySSP is unique in its inclusion of indels, flexibility in allowing for non-stationary patterns, and output of ancestral sequences. Some of these features can individually be found in existing programs, but have not all have been previously available in a single package. PMID:19325855

CyberMedVPS: visual programming for development of simulators.

PubMed

Morais, Aline M; Machado, Liliane S

2011-01-01

Computer applications based on Virtual Reality (VR) has been outstanding in training and teaching in the medical filed due to their ability to simulate realistic in which users can practice skills and decision making in different situations. But was realized in these frameworks a hard interaction of non-programmers users. Based on this problematic will be shown the CyberMedVPS, a graphical module which implement Visual Programming concepts to solve an interaction trouble. Frameworks to develop such simulators are available but their use demands knowledge of programming. Based on this problematic will be shown the CyberMedVPS, a graphical module for the CyberMed framework, which implements Visual Programming concepts to allow the development of simulators by non-programmers professionals of the medical field.

An Atmospheric Guidance Algorithm Testbed for the Mars Surveyor Program 2001 Orbiter and Lander

NASA Technical Reports Server (NTRS)

Striepe, Scott A.; Queen, Eric M.; Powell, Richard W.; Braun, Robert D.; Cheatwood, F. McNeil; Aguirre, John T.; Sachi, Laura A.; Lyons, Daniel T.

1998-01-01

An Atmospheric Flight Team was formed by the Mars Surveyor Program '01 mission office to develop aerocapture and precision landing testbed simulations and candidate guidance algorithms. Three- and six-degree-of-freedom Mars atmospheric flight simulations have been developed for testing, evaluation, and analysis of candidate guidance algorithms for the Mars Surveyor Program 2001 Orbiter and Lander. These simulations are built around the Program to Optimize Simulated Trajectories. Subroutines were supplied by Atmospheric Flight Team members for modeling the Mars atmosphere, spacecraft control system, aeroshell aerodynamic characteristics, and other Mars 2001 mission specific models. This paper describes these models and their perturbations applied during Monte Carlo analyses to develop, test, and characterize candidate guidance algorithms.

A Web-Based Simulation Tool on The Performance of Different Roofing Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Joe; New, Joshua Ryan; Miller, William A

The Roof Savings Calculator (www.roofcalc.com) provides the general public with a web-based program for calculating the energy savings of different roofing and attic systems on four different building types (residential, office, retail, and warehouse) in 239 US TMY2 locations. The core simulation engine of the RSC is doe2attic, which couples the AtticSim program developed by Oak Ridge National Laboratory with the DOE-2.1E program originally developed by Lawrence Berkeley National Laboratory a widely used whole-building simulation program since the 1980 s. Although simulating heat flows through the roof may seem to be an easy task, simulating the net effect of roofingmore » strategies on building heating and cooling energy use can be quite challenging. Few simulation programs can reliably capture dynamics including an attic or plenum with large day-night temperature swings, high ventilation rates, significant radiant exchange between the roof and the attic floor and thermal interactions when there are ducts in the attic, as is typical in North American buildings. The doe2attic program has been tested against detailed measurements gathered in two residential buildings in Fresno, California from cooling energy use to air and surface temperatures, and heat fluxes of the roof and attic floor. The focus of this paper is on the doe2attic simulation tool, but the user interface of the RSC will also be briefly described.« less

Two demonstrators and a simulator for a sparse, distributed memory

NASA Technical Reports Server (NTRS)

Brown, Robert L.

1987-01-01

Described are two programs demonstrating different aspects of Kanerva's Sparse, Distributed Memory (SDM). These programs run on Sun 3 workstations, one using color, and have straightforward graphically oriented user interfaces and graphical output. Presented are descriptions of the programs, how to use them, and what they show. Additionally, this paper describes the software simulator behind each program.

[Management and orientation of a hand laceration].

PubMed

Masmejean, Emmanuel

2013-11-01

The good management and orientation of a hand laceration by the general physician is essential. Anatomical knowledge help to judge, after examination, the opportunity for surgery exploration with local anesthesia. Serious stakes are prognostic and economics. The conclusion identifies three clinical pictures : simple superf cial wound requiring a simple clinical control 2 days follow-up, the dubious wound that need to be sent to a specialized center, and the wound requiring care in an emergency hand unit. Extremely urgent wounds are devascularization, amputation and the pressure injection . Bites and wounds on a tendon way require surgical exploration. Bandage should be as simple as possible in order to allow early motion. No antibiotic is given preventively exept for bite, open fractures and/or delay of treatment. Outpatient surgery under loca anesthesia simplifies management.

Computer Simulation of the Population Growth (Schizosaccharomyces Pombe) Experiment.

ERIC Educational Resources Information Center

Daley, Michael; Hillier, Douglas

1981-01-01

Describes a computer program (available from authors) developed to simulate "Growth of a Population (Yeast) Experiment." Students actively revise the counting techniques with realistically simulated haemocytometer or eye-piece grid and are reminded of the necessary dilution technique. Program can be modified to introduce such variables…

E-simulation: preregistration nursing students' evaluation of an online patient deterioration program.

PubMed

Cant, Robyn; Young, Susan; Cooper, Simon J; Porter, Joanne

2015-03-01

This study explores preregistration nursing students' views of a Web-based simulation program: FIRST ACTWeb (Feedback Incorporating Review and Simulation Techniques to Act on Clinical Trends-Web). The multimedia program incorporating three videoed scenarios portrayed by a standardized patient (human actor) aims to improve students' recognition and management of hospital patient deterioration. Participants were 367 final-year nursing students from three universities who completed an online evaluation survey and 19 students from two universities who attended one of five focus groups. Two researchers conducted a thematic analysis of the transcribed narratives. Three core themes identified were as follows: "ease of program use," "experience of e-Simulation," and "satisfaction with the learning experience." The Web-based clinical learning environment was endorsed as functional, feasible, and easy to use and was reported to have high fidelity and realism. Feedback in both focus groups and surveys showed high satisfaction with the learning experience. Overall, evaluation suggested that the Web-based simulation program successfully integrated elements essential for blended learning. Although Web-based educational applications are resource intensive to develop, positive appraisal of program quality, plus program accessibility and repeatability, appears to provide important educational benefits. Further research is needed to determine the transferability of these learning experiences into real-world practice.

Simulated Cardiopulmonary Arrests in a Hospital Setting.

ERIC Educational Resources Information Center

Mishkin, Barbara H.; And Others

1982-01-01

Describes a simulated interdisciplinary role rehearsal for cardiopulmonary arrest to prepare nurses to function effectively. Includes needs analysis, program components, and responses of program participants. (Author)

Water Quality Analysis Simulation Program (WASP)

EPA Pesticide Factsheets

The Water Quality Analysis Simulation Program (WASP) model helps users interpret and predict water quality responses to natural phenomena and manmade pollution for various pollution management decisions.

How a Fully Automated eHealth Program Simulates Three Therapeutic Processes: A Case Study.

PubMed

Holter, Marianne T S; Johansen, Ayna; Brendryen, Håvar

2016-06-28

eHealth programs may be better understood by breaking down the components of one particular program and discussing its potential for interactivity and tailoring in regard to concepts from face-to-face counseling. In the search for the efficacious elements within eHealth programs, it is important to understand how a program using lapse management may simultaneously support working alliance, internalization of motivation, and behavior maintenance. These processes have been applied to fully automated eHealth programs individually. However, given their significance in face-to-face counseling, it may be important to simulate the processes simultaneously in interactive, tailored programs. We propose a theoretical model for how fully automated behavior change eHealth programs may be more effective by simulating a therapist's support of a working alliance, internalization of motivation, and managing lapses. We show how the model is derived from theory and its application to Endre, a fully automated smoking cessation program that engages the user in several "counseling sessions" about quitting. A descriptive case study based on tools from the intervention mapping protocol shows how each therapeutic process is simulated. The program supports the user's working alliance through alliance factors, the nonembodied relational agent Endre and computerized motivational interviewing. Computerized motivational interviewing also supports internalized motivation to quit, whereas a lapse management component responds to lapses. The description operationalizes working alliance, internalization of motivation, and managing lapses, in terms of eHealth support of smoking cessation. A program may simulate working alliance, internalization of motivation, and lapse management through interactivity and individual tailoring, potentially making fully automated eHealth behavior change programs more effective.

How a Fully Automated eHealth Program Simulates Three Therapeutic Processes: A Case Study

PubMed Central

Johansen, Ayna; Brendryen, Håvar

2016-01-01

Background eHealth programs may be better understood by breaking down the components of one particular program and discussing its potential for interactivity and tailoring in regard to concepts from face-to-face counseling. In the search for the efficacious elements within eHealth programs, it is important to understand how a program using lapse management may simultaneously support working alliance, internalization of motivation, and behavior maintenance. These processes have been applied to fully automated eHealth programs individually. However, given their significance in face-to-face counseling, it may be important to simulate the processes simultaneously in interactive, tailored programs. Objective We propose a theoretical model for how fully automated behavior change eHealth programs may be more effective by simulating a therapist’s support of a working alliance, internalization of motivation, and managing lapses. Methods We show how the model is derived from theory and its application to Endre, a fully automated smoking cessation program that engages the user in several “counseling sessions” about quitting. A descriptive case study based on tools from the intervention mapping protocol shows how each therapeutic process is simulated. Results The program supports the user’s working alliance through alliance factors, the nonembodied relational agent Endre and computerized motivational interviewing. Computerized motivational interviewing also supports internalized motivation to quit, whereas a lapse management component responds to lapses. The description operationalizes working alliance, internalization of motivation, and managing lapses, in terms of eHealth support of smoking cessation. Conclusions A program may simulate working alliance, internalization of motivation, and lapse management through interactivity and individual tailoring, potentially making fully automated eHealth behavior change programs more effective. PMID:27354373

Demonstration of Inexact Computing Implemented in the JPEG Compression Algorithm using Probabilistic Boolean Logic applied to CMOS Components

DTIC Science & Technology

2015-12-24

Signal to Noise Ratio SPICE Simulation Program with Integrated Circuit Emphasis TIFF Tagged Image File Format USC University of Southern California xvii...sources can create errors in digital circuits. These effects can be simulated using Simulation Program with Integrated Circuit Emphasis ( SPICE ) or...compute summary statistics. 4.1 Circuit Simulations Noisy analog circuits can be simulated in SPICE or Cadence SpectreTM software via noisy voltage

Simulation of the XV-15 tilt rotor research aircraft

NASA Technical Reports Server (NTRS)

Churchill, G. B.; Dugan, D. C.

1982-01-01

The effective use of simulation from issuance of the request for proposal through conduct of a flight test program for the XV-15 Tilt Rotor Research Aircraft is discussed. From program inception, simulation complemented all phases of XV-15 development. The initial simulation evaluations during the source evaluation board proceedings contributed significantly to performance and stability and control evaluations. Eight subsequent simulation periods provided major contributions in the areas of control concepts; cockpit configuration; handling qualities; pilot workload; failure effects and recovery procedures; and flight boundary problems and recovery procedures. The fidelity of the simulation also made it a valuable pilot training aid, as well as a suitable tool for military and civil mission evaluations. Simulation also provided valuable design data for refinement of automatic flight control systems. Throughout the program, fidelity was a prime issue and resulted in unique data and methods for fidelity evaluation which are presented and discussed.

Monte Carlo simulation of biomolecular systems with BIOMCSIM

NASA Astrophysics Data System (ADS)

Kamberaj, H.; Helms, V.

2001-12-01

A new Monte Carlo simulation program, BIOMCSIM, is presented that has been developed in particular to simulate the behaviour of biomolecular systems, leading to insights and understanding of their functions. The computational complexity in Monte Carlo simulations of high density systems, with large molecules like proteins immersed in a solvent medium, or when simulating the dynamics of water molecules in a protein cavity, is enormous. The program presented in this paper seeks to provide these desirable features putting special emphasis on simulations in grand canonical ensembles. It uses different biasing techniques to increase the convergence of simulations, and periodic load balancing in its parallel version, to maximally utilize the available computer power. In periodic systems, the long-ranged electrostatic interactions can be treated by Ewald summation. The program is modularly organized, and implemented using an ANSI C dialect, so as to enhance its modifiability. Its performance is demonstrated in benchmark applications for the proteins BPTI and Cytochrome c Oxidase.

Performance of the NASA Airborne Radar with the Windshear Database for Forward-Looking Systems

NASA Technical Reports Server (NTRS)

Switzer, George F.; Britt, Charles L.

1996-01-01

This document describes the simulation approach used to test the performance of the NASA airborne windshear radar. An explanation of the actual radar hardware and processing algorithms provides an understanding of the parameters used in the simulation program. This report also contains a brief overview of the NASA airborne windshear radar experimental flight test results. A description of the radar simulation program shows the capabilities of the program and the techniques used for certification evaluation. Simulation of the NASA radar is comprised of three steps. First, the choice of the ground clutter data must be made. The ground clutter is the return from objects in or nearby an airport facility. The choice of the ground clutter also dictates the aircraft flight path since ground clutter is gathered while in flight. The second step is the choice of the radar parameters and the running of the simulation program which properly combines the ground clutter data with simulated windshear weather data. The simulated windshear weather data is comprised of a number of Terminal Area Simulation System (TASS) model results. The final step is the comparison of the radar simulation results to the known windshear data base. The final evaluation of the radar simulation is based on the ability to detect hazardous windshear with the aircraft at a safe distance while at the same time not displaying false alerts.

Taxis through Computer Simulation Programs.

ERIC Educational Resources Information Center

Park, David

1983-01-01

Describes a sequence of five computer programs (listings for Apple II available from author) on tactic responses (oriented movement of a cell, cell group, or whole organism in reponse to stimuli). The simulation programs are useful in helping students examine mechanisms at work in real organisms. (JN)

The nature of undergraduates' conceptual understanding of oxygen transport and utilization in humans: Can cardiopulmonary simulation software enhance learning of propositional knowledge and/or diagnose alternative conceptions in novices and intermediates?

NASA Astrophysics Data System (ADS)

Wissing, Dennis Robert

The purpose of the this research was to explore undergraduates' conceptual development for oxygen transport and utilization, as a component of a cardiopulmonary physiology and advanced respiratory care course in the allied health program. This exploration focused on the student's development of knowledge and the presence of alternative conceptions, prior to, during, and after completing cardiopulmonary physiology and advanced respiratory care courses. Using the simulation program, SimBioSysTM (Samsel, 1994), student-participants completed a series of laboratory exercises focusing on cardiopulmonary disease states. This study examined data gathered from: (1) a novice group receiving the simulation program prior to instruction, (2) a novice group that experienced the simulation program following course completion in cardiopulmonary physiology, and (3) an intermediate group who experienced the simulation program following completion of formal education in Respiratory Care. This research was based on the theory of Human Constructivism as described by Mintzes, Wandersee, and Novak (1997). Data-gathering techniques were based on theories supported by Novak (1984), Wandersee (1997), and Chi (1997). Data were generated by exams, interviews, verbal analysis (Chi, 1997), and concept mapping. Results suggest that simulation may be an effective instructional method for assessing conceptual development and diagnosing alternative conceptions in undergraduates enrolled in a cardiopulmonary science program. Use of simulation in conjunction with clinical interview and concept mapping may assist in verifying gaps in learning and conceptual knowledge. This study found only limited evidence to support the use of computer simulation prior to lecture to augment learning. However, it was demonstrated that students' prelecture experience with the computer simulation helped the instructor assess what the learner knew so he or she could be taught accordingly. In addition, use of computer simulation after formal instruction was shown to be useful in aiding students identified by the instructor as needing remediation.

14 CFR 142.54 - Airline transport pilot certification training program.

Code of Federal Regulations, 2014 CFR

2014-01-01

... training in a flight simulation training device— (1) Holds an aircraft type rating for the aircraft represented by the flight simulation training device utilized in the training program and have received... will be demonstrated in the flight simulation training device; and (2) Satisfies the requirements of...

Creating an Advertising Campaign: An Evaluation Report for the Occupational Exploration Programs.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with advertising, the report contains sections describing the simulation context, evaluation procedures,…

Insurance: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with the insurance field, the report contains sections describing the simulation context, evaluation…

Manufacturing Production: An Evaluation Report for the Occupational Exploration Program.

ERIC Educational Resources Information Center

Altschuld, James W.; And Others

The evaluation report is one of seven produced for the Occupational Exploration Program (OEP), a series of simulated occupational experiences designed for junior high school students. Describing the pilot testing of the simulation dealing with manufacturing production, the report contains sections describing the simulation context, evaluation…

Assessment of virtual reality robotic simulation performance by urology resident trainees.

PubMed

Ruparel, Raaj K; Taylor, Abby S; Patel, Janil; Patel, Vipul R; Heckman, Michael G; Rawal, Bhupendra; Leveillee, Raymond J; Thiel, David D

2014-01-01

To examine resident performance on the Mimic dV-Trainer (MdVT; Mimic Technologies, Inc., Seattle, WA) for correlation with resident trainee level (postgraduate year [PGY]), console experience (CE), and simulator exposure in their training program to assess for internal bias with the simulator. Residents from programs of the Southeastern Section of the American Urologic Association participated. Each resident was scored on 4 simulator tasks (peg board, camera targeting, energy dissection [ED], and needle targeting) with 3 different outcomes (final score, economy of motion score, and time to complete exercise) measured for each task. These scores were evaluated for association with PGY, CE, and simulator exposure. Robotic skills training laboratory. A total of 27 residents from 14 programs of the Southeastern Section of the American Urologic Association participated. Time to complete the ED exercise was significantly shorter for residents who had logged live robotic console compared with those who had not (p = 0.003). There were no other associations with live robotic console time that approached significance (all p ≥ 0.21). The only measure that was significantly associated with PGY was time to complete ED exercise (p = 0.009). No associations with previous utilization of a robotic simulator in the resident's home training program were statistically significant. The ED exercise on the MdVT is most associated with CE and PGY compared with other exercises. Exposure of trainees to the MdVT in training programs does not appear to alter performance scores compared with trainees who do not have the simulator. © 2013 Published by Association of Program Directors in Surgery on behalf of Association of Program Directors in Surgery.

SIMPSON: A General Simulation Program for Solid-State NMR Spectroscopy

NASA Astrophysics Data System (ADS)

Bak, Mads; Rasmussen, Jimmy T.; Nielsen, Niels Chr.

2000-12-01

A computer program for fast and accurate numerical simulation of solid-state NMR experiments is described. The program is designed to emulate a NMR spectrometer by letting the user specify high-level NMR concepts such as spin systems, nuclear spin interactions, RF irradiation, free precession, phase cycling, coherence-order filtering, and implicit/explicit acquisition. These elements are implemented using the Tcl scripting language to ensure a minimum of programming overhead and direct interpretation without the need for compilation, while maintaining the flexibility of a full-featured programming language. Basicly, there are no intrinsic limitations to the number of spins, types of interactions, sample conditions (static or spinning, powders, uniaxially oriented molecules, single crystals, or solutions), and the complexity or number of spectral dimensions for the pulse sequence. The applicability ranges from simple 1D experiments to advanced multiple-pulse and multiple-dimensional experiments, series of simulations, parameter scans, complex data manipulation/visualization, and iterative fitting of simulated to experimental spectra. A major effort has been devoted to optimizing the computation speed using state-of-the-art algorithms for the time-consuming parts of the calculations implemented in the core of the program using the C programming language. Modification and maintenance of the program are facilitated by releasing the program as open source software (General Public License) currently at http://nmr.imsb.au.dk. The general features of the program are demonstrated by numerical simulations of various aspects for REDOR, rotational resonance, DRAMA, DRAWS, HORROR, C7, TEDOR, POST-C7, CW decoupling, TPPM, F-SLG, SLF, SEMA-CP, PISEMA, RFDR, QCPMG-MAS, and MQ-MAS experiments.

SIMPSON: A general simulation program for solid-state NMR spectroscopy

NASA Astrophysics Data System (ADS)

Bak, Mads; Rasmussen, Jimmy T.; Nielsen, Niels Chr.

2011-12-01

A computer program for fast and accurate numerical simulation of solid-state NMR experiments is described. The program is designed to emulate a NMR spectrometer by letting the user specify high-level NMR concepts such as spin systems, nuclear spin interactions, RF irradiation, free precession, phase cycling, coherence-order filtering, and implicit/explicit acquisition. These elements are implemented using the Tel scripting language to ensure a minimum of programming overhead and direct interpretation without the need for compilation, while maintaining the flexibility of a full-featured programming language. Basicly, there are no intrinsic limitations to the number of spins, types of interactions, sample conditions (static or spinning, powders, uniaxially oriented molecules, single crystals, or solutions), and the complexity or number of spectral dimensions for the pulse sequence. The applicability ranges from simple ID experiments to advanced multiple-pulse and multiple-dimensional experiments, series of simulations, parameter scans, complex data manipulation/visualization, and iterative fitting of simulated to experimental spectra. A major effort has been devoted to optimizing the computation speed using state-of-the-art algorithms for the time-consuming parts of the calculations implemented in the core of the program using the C programming language. Modification and maintenance of the program are facilitated by releasing the program as open source software (General Public License) currently at http://nmr.imsb.au.dk. The general features of the program are demonstrated by numerical simulations of various aspects for REDOR, rotational resonance, DRAMA, DRAWS, HORROR, C7, TEDOR, POST-C7, CW decoupling, TPPM, F-SLG, SLF, SEMA-CP, PISEMA, RFDR, QCPMG-MAS, and MQ-MAS experiments.

Using Software Zelio Soft in Educational Process to Simulation Control Programs for Intelligent Relays

NASA Astrophysics Data System (ADS)

Michalik, Peter; Mital, Dusan; Zajac, Jozef; Brezikova, Katarina; Duplak, Jan; Hatala, Michal; Radchenko, Svetlana

2016-10-01

Article deals with point to using intelligent relay and PLC systems in practice, to their architecture and principles of programming and simulations for education process on all types of school from secondary to universities. Aim of the article is proposal of simple examples of applications, where is demonstrated methodology of programming on real simple practice examples and shown using of chosen instructions. In practical part is described process of creating schemas and describing of function blocks, where are described methodologies of creating program and simulations of output reactions on changeable inputs for intelligent relays.

An automated procedure for developing hybrid computer simulations of turbofan engines

NASA Technical Reports Server (NTRS)

Szuch, J. R.; Krosel, S. M.

1980-01-01

A systematic, computer-aided, self-documenting methodology for developing hybrid computer simulations of turbofan engines is presented. The methodology makes use of a host program that can run on a large digital computer and a machine-dependent target (hybrid) program. The host program performs all of the calculations and date manipulations needed to transform user-supplied engine design information to a form suitable for the hybrid computer. The host program also trims the self contained engine model to match specified design point information. A test case is described and comparisons between hybrid simulation and specified engine performance data are presented.

Planning Models for Tuberculosis Control Programs

PubMed Central

Chorba, Ronald W.; Sanders, J. L.

1971-01-01

A discrete-state, discrete-time simulation model of tuberculosis is presented, with submodels of preventive interventions. The model allows prediction of the prevalence of the disease over the simulation period. Preventive and control programs and their optimal budgets may be planned by using the model for cost-benefit analysis: costs are assigned to the program components and disease outcomes to determine the ratio of program expenditures to future savings on medical and socioeconomic costs of tuberculosis. Optimization is achieved by allocating funds in successive increments to alternative program components in simulation and identifying those components that lead to the greatest reduction in prevalence for the given level of expenditure. The method is applied to four hypothetical disease prevalence situations. PMID:4999448

Technique to eliminate computational instability in multibody simulations employing the Lagrange multiplier

NASA Technical Reports Server (NTRS)

Watts, G.

1992-01-01

A programming technique to eliminate computational instability in multibody simulations that use the Lagrange multiplier is presented. The computational instability occurs when the attached bodies drift apart and violate the constraints. The programming technique uses the constraint equation, instead of integration, to determine the coordinates that are not independent. Although the equations of motion are unchanged, a complete derivation of the incorporation of the Lagrange multiplier into the equation of motion for two bodies is presented. A listing of a digital computer program which uses the programming technique to eliminate computational instability is also presented. The computer program simulates a solid rocket booster and parachute connected by a frictionless swivel.

Capabilities and applications of the Program to Optimize Simulated Trajectories (POST). Program summary document

NASA Technical Reports Server (NTRS)

Brauer, G. L.; Cornick, D. E.; Stevenson, R.

1977-01-01

The capabilities and applications of the three-degree-of-freedom (3DOF) version and the six-degree-of-freedom (6DOF) version of the Program to Optimize Simulated Trajectories (POST) are summarized. The document supplements the detailed program manuals by providing additional information that motivates and clarifies basic capabilities, input procedures, applications and computer requirements of these programs. The information will enable prospective users to evaluate the programs, and to determine if they are applicable to their problems. Enough information is given to enable managerial personnel to evaluate the capabilities of the programs and describes the POST structure, formulation, input and output procedures, sample cases, and computer requirements. The report also provides answers to basic questions concerning planet and vehicle modeling, simulation accuracy, optimization capabilities, and general input rules. Several sample cases are presented.

An Interactive Computer Program for Simulating the Effects of Olivine Fractionation from Basaltic and Ultrabasic Liquids.

ERIC Educational Resources Information Center

Pearce, Thomas H.

1983-01-01

Describes interactive computer program (listing available from author) which simulates olivine fractionation from basaltic/ultrabasic liquid. The menu-driven nature of the program (for Apple II microcomputer) allows students to select ideal Rayleigh fractionation or equilibrium crystallization. (JN)

ALOG: A spreadsheet-based program for generating artificial logs

Treesearch

Matthew F. Winn; Randolph H. Wynne; Philip A. Araman

2004-01-01

Log sawing simulation computer programs can be valuable tools for training sawyers as well as for testing different sawing patterns. Most available simulation programs rely on databases from which to draw logs and can be very costly and time-consuming to develop. ALOG (Artificial LOg Generator) is a Microsoft Excel®-based computer program that was developed to...

Improving Thai Students' Understanding of Concepts in Protein Purification by Using Thai and English Versions of a Simulation Program

ERIC Educational Resources Information Center

Phornphisutthimas, Somkiat; Panijpan, Bhinyo; Wood, Edward J.; Booth, Andrew G.

2007-01-01

To support student learning in biochemistry and related courses, a simulation program, the Protein Purification Program, offers an alternative multimedia-based tool. This program has now been translated to produce a Thai version. However, translation from the original into the Thai language is limited by the differences between the language…

Minimum Hamiltonian Ascent Trajectory Evaluation (MASTRE) program (update to automatic flight trajectory design, performance prediction, and vehicle sizing for support of Shuttle and Shuttle derived vehicles) engineering manual

NASA Technical Reports Server (NTRS)

Lyons, J. T.

1993-01-01

The Minimum Hamiltonian Ascent Trajectory Evaluation (MASTRE) program and its predecessors, the ROBOT and the RAGMOP programs, have had a long history of supporting MSFC in the simulation of space boosters for the purpose of performance evaluation. The ROBOT program was used in the simulation of the Saturn 1B and Saturn 5 vehicles in the 1960's and provided the first utilization of the minimum Hamiltonian (or min-H) methodology and the steepest ascent technique to solve the optimum trajectory problem. The advent of the Space Shuttle in the 1970's and its complex airplane design required a redesign of the trajectory simulation code since aerodynamic flight and controllability were required for proper simulation. The RAGMOP program was the first attempt to incorporate the complex equations of the Space Shuttle into an optimization tool by using an optimization method based on steepest ascent techniques (but without the min-H methodology). Development of the complex partial derivatives associated with the Space Shuttle configuration and using techniques from the RAGMOP program, the ROBOT program was redesigned to incorporate these additional complexities. This redesign created the MASTRE program, which was referred to as the Minimum Hamiltonian Ascent Shuttle TRajectory Evaluation program at that time. Unique to this program were first-stage (or booster) nonlinear aerodynamics, upper-stage linear aerodynamics, engine control via moment balance, liquid and solid thrust forces, variable liquid throttling to maintain constant acceleration limits, and a total upgrade of the equations used in the forward and backward integration segments of the program. This modification of the MASTRE code has been used to simulate the new space vehicles associated with the National Launch Systems (NLS). Although not as complicated as the Space Shuttle, the simulation and analysis of the NLS vehicles required additional modifications to the MASTRE program in the areas of providing additional flexibility in the use of the program, allowing additional optimization options, and providing special options for the NLS configuration.

Simulation of root forms using cellular automata model

NASA Astrophysics Data System (ADS)

Winarno, Nanang; Prima, Eka Cahya; Afifah, Ratih Mega Ayu

2016-02-01

This research aims to produce a simulation program for root forms using cellular automata model. Stephen Wolfram in his book entitled "A New Kind of Science" discusses the formation rules based on the statistical analysis. In accordance with Stephen Wolfram's investigation, the research will develop a basic idea of computer program using Delphi 7 programming language. To best of our knowledge, there is no previous research developing a simulation describing root forms using the cellular automata model compared to the natural root form with the presence of stone addition as the disturbance. The result shows that (1) the simulation used four rules comparing results of the program towards the natural photographs and each rule had shown different root forms; (2) the stone disturbances prevent the root growth and the multiplication of root forms had been successfully modeled. Therefore, this research had added some stones, which have size of 120 cells placed randomly in the soil. Like in nature, stones cannot be penetrated by plant roots. The result showed that it is very likely to further develop the program of simulating root forms by 50 variations.

Apollo experience report: Guidance and control systems. Engineering simulation program

NASA Technical Reports Server (NTRS)

Gilbert, D. W.

1973-01-01

The Apollo Program experience from early 1962 to July 1969 with respect to the engineering-simulation support and the problems encountered is summarized in this report. Engineering simulation in support of the Apollo guidance and control system is discussed in terms of design analysis and verification, certification of hardware in closed-loop operation, verification of hardware/software compatibility, and verification of both software and procedures for each mission. The magnitude, time, and cost of the engineering simulations are described with respect to hardware availability, NASA and contractor facilities (for verification of the command module, the lunar module, and the primary guidance, navigation, and control system), and scheduling and planning considerations. Recommendations are made regarding implementation of similar, large-scale simulations for future programs.

Comprehensive silicon solar cell computer modeling

NASA Technical Reports Server (NTRS)

Lamorte, M. F.

1984-01-01

The development of an efficient, comprehensive Si solar cell modeling program that has the capability of simulation accuracy of 5 percent or less is examined. A general investigation of computerized simulation is provided. Computer simulation programs are subdivided into a number of major tasks: (1) analytical method used to represent the physical system; (2) phenomena submodels that comprise the simulation of the system; (3) coding of the analysis and the phenomena submodels; (4) coding scheme that results in efficient use of the CPU so that CPU costs are low; and (5) modularized simulation program with respect to structures that may be analyzed, addition and/or modification of phenomena submodels as new experimental data become available, and the addition of other photovoltaic materials.

THE MARK I BUSINESS SYSTEM SIMULATION MODEL

DTIC Science & Technology

of a large-scale business simulation model as a vehicle for doing research in management controls. The major results of the program were the...development of the Mark I business simulation model and the Simulation Package (SIMPAC). SIMPAC is a method and set of programs facilitating the construction...of large simulation models. The object of this document is to describe the Mark I Corporation model, state why parts of the business were modeled as they were, and indicate the research applications of the model. (Author)

Implementation and evaluation of a simulation curriculum for paediatric residency programs including just-in-time in situ mock codes.

PubMed

Sam, Jonathan; Pierse, Michael; Al-Qahtani, Abdullah; Cheng, Adam

2012-02-01

To develop, implement and evaluate a simulation-based acute care curriculum in a paediatric residency program using an integrated and longitudinal approach. Curriculum framework consisting of three modular, year-specific courses and longitudinal just-in-time, in situ mock codes. Paediatric residency program at BC Children's Hospital, Vancouver, British Columbia. The three year-specific courses focused on the critical first 5 min, complex medical management and crisis resource management, respectively. The just-in-time in situ mock codes simulated the acute deterioration of an existing ward patient, prepared the actual multidisciplinary code team, and primed the surrounding crisis support systems. Each curriculum component was evaluated with surveys using a five-point Likert scale. A total of 40 resident surveys were completed after each of the modular courses, and an additional 28 surveys were completed for the overall simulation curriculum. The highest Likert scores were for hands-on skill stations, immersive simulation environment and crisis resource management teaching. Survey results also suggested that just-in-time mock codes were realistic, reinforced learning, and prepared ward teams for patient deterioration. A simulation-based acute care curriculum was successfully integrated into a paediatric residency program. It provides a model for integrating simulation-based learning into other training programs, as well as a model for any hospital that wishes to improve paediatric resuscitation outcomes using just-in-time in situ mock codes.

Two Hours of Teamwork Training Improves Teamwork in Simulated Cardiopulmonary Arrest Events.

PubMed

Mahramus, Tara L; Penoyer, Daleen A; Waterval, Eugene M E; Sole, Mary L; Bowe, Eileen M

2016-01-01

Teamwork during cardiopulmonary arrest events is important for resuscitation. Teamwork improvement programs are usually lengthy. This study assessed the effectiveness of a 2-hour teamwork training program. A prospective, pretest/posttest, quasi-experimental design assessed the teamwork training program targeted to resident physicians, nurses, and respiratory therapists. Participants took part in a simulated cardiac arrest. After the simulation, participants and trained observers assessed perceptions of teamwork using the Team Emergency Assessment Measure (TEAM) tool (ratings of 0 [low] to 4 [high]). A debriefing and 45 minutes of teamwork education followed. Participants then took part in a second simulated cardiac arrest scenario. Afterward, participants and observers assessed teamwork. Seventy-three team members participated-resident physicians (25%), registered nurses (32%), and respiratory therapists (41%). The physicians had significantly less experience on code teams (P < .001). Baseline teamwork scores were 2.57 to 2.72. Participants' mean (SD) scores on the TEAM tool for the first and second simulations were 3.2 (0.5) and 3.7 (0.4), respectively (P < .001). Observers' mean (SD) TEAM scores for the first and second simulations were 3.0 (0.5) and 3.7 (0.3), respectively (P < .001). Program evaluations by participants were positive. A 2-hour simulation-based teamwork educational intervention resulted in improved perceptions of teamwork behaviors. Participants reported interactions with other disciplines, teamwork behavior education, and debriefing sessions were beneficial for enhancing the program.

A fortran program for Monte Carlo simulation of oil-field discovery sequences

USGS Publications Warehouse

Bohling, Geoffrey C.; Davis, J.C.

1993-01-01

We have developed a program for performing Monte Carlo simulation of oil-field discovery histories. A synthetic parent population of fields is generated as a finite sample from a distribution of specified form. The discovery sequence then is simulated by sampling without replacement from this parent population in accordance with a probabilistic discovery process model. The program computes a chi-squared deviation between synthetic and actual discovery sequences as a function of the parameters of the discovery process model, the number of fields in the parent population, and the distributional parameters of the parent population. The program employs the three-parameter log gamma model for the distribution of field sizes and employs a two-parameter discovery process model, allowing the simulation of a wide range of scenarios. ?? 1993.

SMSIM--Fortran programs for simulating ground motions from earthquakes: Version 2.0.--a revision of OFR 96-80-A

USGS Publications Warehouse

Boore, David M.

2000-01-01

A simple and powerful method for simulating ground motions is based on the assumption that the amplitude of ground motion at a site can be specified in a deterministic way, with a random phase spectrum modified such that the motion is distributed over a duration related to the earthquake magnitude and to distance from the source. This method of simulating ground motions often goes by the name "the stochastic method." It is particularly useful for simulating the higher-frequency ground motions of most interest to engineers, and it is widely used to predict ground motions for regions of the world in which recordings of motion from damaging earthquakes are not available. This simple method has been successful in matching a variety of ground-motion measures for earthquakes with seismic moments spanning more than 12 orders of magnitude. One of the essential characteristics of the method is that it distills what is known about the various factors affecting ground motions (source, path, and site) into simple functional forms that can be used to predict ground motions. SMSIM is a set of programs for simulating ground motions based on the stochastic method. This Open-File Report is a revision of an earlier report (Boore, 1996) describing a set of programs for simulating ground motions from earthquakes. The programs are based on modifications I have made to the stochastic method first introduced by Hanks and McGuire (1981). The report contains source codes, written in Fortran, and executables that can be used on a PC. Programs are included both for time-domain and for random vibration simulations. In addition, programs are included to produce Fourier amplitude spectra for the models used in the simulations and to convert shear velocity vs. depth into frequency-dependent amplification. The revision to the previous report is needed because the input and output files have changed significantly, and a number of new programs have been included in the set.

The role of simulation in neurosurgical education: a survey of 99 United States neurosurgery program directors.

PubMed

Ganju, Aruna; Aoun, Salah G; Daou, Marc R; El Ahmadieh, Tarek Y; Chang, Alice; Wang, Lucy; Batjer, H Hunt; Bendok, Bernard R

2013-11-01

With the reduction of resident work hours and the increasing focus on patient safety, it has become evident that simulation has a growing role to play in surgical education. We surveyed the program directors of 99 U.S. Neurosurgery programs in an effort to better understand how simulation can be implemented in Neurosurgery and to gain insight into key issues that are currently being discussed amongst Neurosurgical educators. A 14-item questionnaire was emailed to 99 Neurosurgery residency program directors. Questions assessed the clinical impact of simulation, the role of simulation in academia, the investments required in time and money, and the model best suited for simulation. The survey response rate was 53.5%. Seventy-two percent of respondents believed that simulation would improve patient outcome, 74% that it could supplement conventional training, but only 25% that it could replace it. The majority strongly believed that it could help preparing complex cases and could be of use to attending faculty. Forty-five percent thought that residents should achieve pre-defined levels of proficiency on simulators before working on patients. Seventy-four percent of respondents declared they would make simulator practice mandatory if available, and the majority was willing to invest daily time and considerable funds on simulators. Cadavers were the least preferred models to use compared to virtual simulation and noncadaveric physical models. Simulation should be integrated in Neurosurgery training curricula. The validation of available tools is the next step that will enable the training, acquisition, and testing of neurosurgical skills. Copyright © 2013 Elsevier Inc. All rights reserved.

A simulation model of IT risk on program trading

NASA Astrophysics Data System (ADS)

Xia, Bingying; Jiang, Wenbao; Luo, Guangxuan

2015-12-01

The biggest difficulty for Program trading IT risk measures lies in the loss of data, in view of this situation, the current scholars approach is collecting court, network and other public media such as all kinds of accident of IT both at home and abroad for data collection, and the loss of IT risk quantitative analysis based on this database. However, the IT risk loss database established by this method can only fuzzy reflect the real situation and not for real to make fundamental explanation. In this paper, based on the study of the concept and steps of the MC simulation, we use computer simulation method, by using the MC simulation method in the "Program trading simulation system" developed by team to simulate the real programming trading and get the IT risk loss of data through its IT failure experiment, at the end of the article, on the effectiveness of the experimental data is verified. In this way, better overcome the deficiency of the traditional research method and solves the problem of lack of IT risk data in quantitative research. More empirically provides researchers with a set of simulation method are used to study the ideas and the process template.

Efficient Adaptive FIR and IIR Filters.

DTIC Science & Technology

1979-12-01

Squared) algorithm. -An analysis of the simplified gradient approach is presented and confirmed experimentally for the specific example of an adaptive line...APPENDIX A - SIMULATION 130 A.1 - THE SIMULATION METHOD 130 A.2 - FIR SIMULATION PRO)GRAM 133 A.3 - IIR SIMULATION PROGRAM 136 APPENDIX B - RANDOM...surface. The generation of the reference signal is a key consi- deration in adaptive filter implementation. There are various practical methods as

Method and Process for the Creation of Modeling and Simulation Tools for Human Crowd Behavior

DTIC Science & Technology

2014-07-23

Support• Program Executive Office Ground Combat Systems • Program Executive Office Soldier TACOM LCMC MG Michael J. Terry Assigned/Direct Support...environmental technologies and explosive ordnance disposal Fire Control: Battlefield digitization; embedded system software; aero ballistics and...MRAD – Handheld stand-off NLW operated by Control Force • Simulated Projectile Weapon • Simulated Handheld Directed Energy NLW ( VDE ) – Simulated

Three Dimensional Thermal Pollution Models. Volume 2; Rigid-Lid Models

NASA Technical Reports Server (NTRS)

Lee, S. S.; Sengupta, S.

1978-01-01

Three versions of rigid lid programs are presented: one for near field simulation; the second for far field unstratified situations; and the third for stratified basins, far field simulation. The near field simulates thermal plume areas, and the far field version simulates larger receiving aquatic ecosystems. Since these versions have many common subroutines, a unified testing is provided, with main programs for the three possible conditions listed.

A systematic review of the effectiveness of simulation-based education on satisfaction and learning outcomes in nurse practitioner programs.

PubMed

Warren, Jessie N; Luctkar-Flude, Marian; Godfrey, Christina; Lukewich, Julia

2016-11-01

High-fidelity simulation (HFS) is becoming an integral component in healthcare education programs. There is considerable evidence demonstrating the effectiveness of HFS on satisfaction and learning outcomes within undergraduate nursing programs; however, there are few studies that have investigated its use and effectiveness within nurse practitioner (NP) programs. To synthesize the best available evidence about the effectiveness of HFS within NP education programs worldwide. The specific review question was: what is the effect of HFS on learner satisfaction, knowledge, attitudes, and skill performance in NP education? Joanna Briggs Institute systematic review methodology was utilized. The following databases were searched: MEDLINE, CINAHL, EMBASE, Epistemonikos, PROSPERO, HealthSTAR, AMED, Cochrane, Global Health and PsycINFO. Studies were included if they were quantitative in nature and reported on any aspect HFS within a NP program. Ten studies were included in the review. All studies were conducted in the United States and published between 2007 and 2014. Outcomes explored included: knowledge, attitudes, skills and satisfaction. The majority of studies compared HFS to online learning or traditional classroom lecture. Most study scenarios featured high acuity, low frequency events within acute care settings; only two studies utilized scenarios simulated within primary care. There is limited evidence supporting the use of HFS within NP programs. In general, HFS increases students' knowledge and confidence, and students are more satisfied with simulation-based teaching in comparison to other methods. Future studies should explore the effectiveness of simulation training within NP programs in reducing the theory to practice gap, and evaluate knowledge retention, transferability to real patient situations, and impact of simulation on patient outcomes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Monte Carlo generator ELRADGEN 2.0 for simulation of radiative events in elastic ep-scattering of polarized particles

NASA Astrophysics Data System (ADS)

Akushevich, I.; Filoti, O. F.; Ilyichev, A.; Shumeiko, N.

2012-07-01

The structure and algorithms of the Monte Carlo generator ELRADGEN 2.0 designed to simulate radiative events in polarized ep-scattering are presented. The full set of analytical expressions for the QED radiative corrections is presented and discussed in detail. Algorithmic improvements implemented to provide faster simulation of hard real photon events are described. Numerical tests show high quality of generation of photonic variables and radiatively corrected cross section. The comparison of the elastic radiative tail simulated within the kinematical conditions of the BLAST experiment at MIT BATES shows a good agreement with experimental data. Catalogue identifier: AELO_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AELO_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC license, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 1299 No. of bytes in distributed program, including test data, etc.: 11 348 Distribution format: tar.gz Programming language: FORTRAN 77 Computer: All Operating system: Any RAM: 1 MB Classification: 11.2, 11.4 Nature of problem: Simulation of radiative events in polarized ep-scattering. Solution method: Monte Carlo simulation according to the distributions of the real photon kinematic variables that are calculated by the covariant method of QED radiative correction estimation. The approach provides rather fast and accurate generation. Running time: The simulation of 108 radiative events for itest:=1 takes up to 52 seconds on Pentium(R) Dual-Core 2.00 GHz processor.

Use of multiscale zirconium alloy deformation models in nuclear fuel behavior analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montgomery, Robert, E-mail: robert.montgomery@pnnl.gov; Tomé, Carlos, E-mail: tome@lanl.gov; Liu, Wenfeng, E-mail: wenfeng.liu@anatech.com

Accurate prediction of cladding mechanical behavior is a key aspect of modeling nuclear fuel behavior, especially for conditions of pellet-cladding interaction (PCI), reactivity-initiated accidents (RIA), and loss of coolant accidents (LOCA). Current approaches to fuel performance modeling rely on empirical constitutive models for cladding creep, growth and plastic deformation, which are limited to the materials and conditions for which the models were developed. To improve upon this approach, a microstructurally-based zirconium alloy mechanical deformation analysis capability is being developed within the United States Department of Energy Consortium for Advanced Simulation of Light Water Reactors (CASL). Specifically, the viscoplastic self-consistent (VPSC)more » polycrystal plasticity modeling approach, developed by Lebensohn and Tomé [1], has been coupled with the BISON engineering scale fuel performance code to represent the mechanistic material processes controlling the deformation behavior of light water reactor (LWR) cladding. A critical component of VPSC is the representation of the crystallographic nature (defect and dislocation movement) and orientation of the grains within the matrix material and the ability to account for the role of texture on deformation. A future goal is for VPSC to obtain information on reaction rate kinetics from atomistic calculations to inform the defect and dislocation behavior models described in VPSC. The multiscale modeling of cladding deformation mechanisms allowed by VPSC far exceed the functionality of typical semi-empirical constitutive models employed in nuclear fuel behavior codes to model irradiation growth and creep, thermal creep, or plasticity. This paper describes the implementation of an interface between VPSC and BISON and provides initial results utilizing the coupled functionality.« less

Ultra-High Temperature Steam Corrosion of Complex Silicates for Nuclear Applications: A Computational Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rashkeev, Sergey N.; Glazoff, Michael V.; Tokuhiro, Akira

2014-01-01

Stability of materials under extreme conditions is an important issue for safety of nuclear reactors. Presently, silicon carbide (SiC) is being studied as a cladding material candidate for fuel rods in boiling-water and pressurized water-cooled reactors (BWRs and PWRs) that would substitute or modify traditional zircaloy materials. The rate of corrosion of the SiC ceramics in hot vapor environment (up to 2200 degrees C) simulating emergency conditions of light water reactor (LWR) depends on many environmental factors such as pressure, temperature, viscosity, and surface quality. Using the paralinear oxidation theory developed for ceramics in the combustion reactor environment, we estimatedmore » the corrosion rate of SiC ceramics under the conditions representing a significant power excursion in a LWR. It was established that a significant time – at least 100 h – is required for a typical SiC braiding to significantly degrade even in the most aggressive vapor environment (with temperatures up to 2200 °C) which is possible in a LWR at emergency condition. This provides evidence in favor of using the SiC coatings/braidings for additional protection of nuclear reactor rods against off-normal material degradation during power excursions or LOCA incidents. Additionally, we discuss possibilities of using other silica based ceramics in order to find materials with even higher corrosion resistance than SiC. In particular, we found that zircon (ZrSiO4) is also a very promising material for nuclear applications. Thermodynamic and first-principles atomic-scale calculations provide evidence of zircon thermodynamic stability in aggressive environments at least up to 1535 degrees C.« less

Using Discrete Event Simulation for Programming Model Exploration at Extreme-Scale: Macroscale Components for the Structural Simulation Toolkit (SST).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilke, Jeremiah J; Kenny, Joseph P.

2015-02-01

Discrete event simulation provides a powerful mechanism for designing and testing new extreme- scale programming models for high-performance computing. Rather than debug, run, and wait for results on an actual system, design can first iterate through a simulator. This is particularly useful when test beds cannot be used, i.e. to explore hardware or scales that do not yet exist or are inaccessible. Here we detail the macroscale components of the structural simulation toolkit (SST). Instead of depending on trace replay or state machines, the simulator is architected to execute real code on real software stacks. Our particular user-space threading frameworkmore » allows massive scales to be simulated even on small clusters. The link between the discrete event core and the threading framework allows interesting performance metrics like call graphs to be collected from a simulated run. Performance analysis via simulation can thus become an important phase in extreme-scale programming model and runtime system design via the SST macroscale components.« less

Energy simulation and optimization for a small commercial building through Modelica

NASA Astrophysics Data System (ADS)

Rivas, Bryan

Small commercial buildings make up the majority of buildings in the United States. Energy consumed by these buildings is expected to drastically increase in the next few decades, with a large percentage of the energy consumed attributed to cooling systems. This work presents the simulation and optimization of a thermostat schedule to minimize energy consumption in a small commercial building test bed during the cooling season. The simulation occurs through the use of the multi-engineering domain Dymola environment based on the Modelica open source programming language and is optimized with the Java based optimization program GenOpt. The simulation uses both physically based modeling utilizing heat transfer principles for the building and regression analysis for energy consumption. GenOpt is dynamically coupled to Dymola through various interface files. There are very few studies that have coupled GenOpt to a building simulation program and even fewer studies have used Dymola for building simulation as extensively as the work presented here. The work presented proves Dymola as a viable alternative to other building simulation programs such as EnergyPlus and MatLab. The model developed is used to simulate the energy consumption of a test bed, a commissioned real world small commercial building, while maintaining indoor thermal comfort. Potential applications include smart or intelligent building systems, predictive simulation of small commercial buildings, and building diagnostics.

A Crisis in Space--A Futuristic Simulation Using Creative Problem Solving.

ERIC Educational Resources Information Center

Clode, Linda

1992-01-01

An enrichment program developed for sixth-grade gifted students combined creative problem solving with future studies in a way that would simulate real life crisis problem solving. The program involved forecasting problems of the future requiring evacuation of Earth, assuming roles on a spaceship, and simulating crises as the spaceship traveled to…

Use of Immersive Simulations to Enhance Graduate Student Learning: Implications for Educational Leadership Programs

ERIC Educational Resources Information Center

Voelkel, Robert H.; Johnson, Christie W.; Gilbert, Kristen A.

2016-01-01

The purpose of this article is to present how one university incorporates immersive simulations through platforms which employ avatars to enhance graduate student understanding and learning in educational leadership programs. While using simulations and immersive virtual environments continues to grow, the literature suggests limited evidence of…

Building Reflective Practice through an Online Diversity Simulation in an Undergraduate Teacher Education Program

ERIC Educational Resources Information Center

Manburg, Jamie; Moore, Rashid; Griffin, David; Seperson, Marvin

2017-01-01

This paper discusses preservice teachers' perceptions of an online, in-house diversity simulation in an undergraduate teacher education program conducted over a 3-year period. The diversity simulation was a nontraditional capstone experience for 193 preservice teachers in majors ranging from early childhood to secondary education. The diversity…

Technology survey of computer software as applicable to the MIUS project

NASA Technical Reports Server (NTRS)

Fulbright, B. E.

1975-01-01

Existing computer software, available from either governmental or private sources, applicable to modular integrated utility system program simulation is surveyed. Several programs and subprograms are described to provide a consolidated reference, and a bibliography is included. The report covers the two broad areas of design simulation and system simulation.

Workflow of the Grover algorithm simulation incorporating CUDA and GPGPU

NASA Astrophysics Data System (ADS)

Lu, Xiangwen; Yuan, Jiabin; Zhang, Weiwei

2013-09-01

The Grover quantum search algorithm, one of only a few representative quantum algorithms, can speed up many classical algorithms that use search heuristics. No true quantum computer has yet been developed. For the present, simulation is one effective means of verifying the search algorithm. In this work, we focus on the simulation workflow using a compute unified device architecture (CUDA). Two simulation workflow schemes are proposed. These schemes combine the characteristics of the Grover algorithm and the parallelism of general-purpose computing on graphics processing units (GPGPU). We also analyzed the optimization of memory space and memory access from this perspective. We implemented four programs on CUDA to evaluate the performance of schemes and optimization. Through experimentation, we analyzed the organization of threads suited to Grover algorithm simulations, compared the storage costs of the four programs, and validated the effectiveness of optimization. Experimental results also showed that the distinguished program on CUDA outperformed the serial program of libquantum on a CPU with a speedup of up to 23 times (12 times on average), depending on the scale of the simulation.

Simulating Descent and Landing of a Spacecraft

NASA Technical Reports Server (NTRS)

Balaram, J.; Jain, Abhinandan; Martin, Bryan; Lim, Christopher; Henriquez, David; McMahon, Elihu; Sohl, Garrett; Banerjee, Pranab; Steele, Robert; Bentley, Timothy

2005-01-01

The Dynamics Simulator for Entry, Descent, and Surface landing (DSENDS) software performs high-fidelity simulation of the Entry, Descent, and Landing (EDL) of a spacecraft into the atmosphere and onto the surface of a planet or a smaller body. DSENDS is an extension of the DShell and DARTS programs, which afford capabilities for mathematical modeling of the dynamics of a spacecraft as a whole and of its instruments, actuators, and other subsystems. DSENDS enables the modeling (including real-time simulation) of flight-train elements and all spacecraft responses during various phases of EDL. DSENDS provides high-fidelity models of the aerodynamics of entry bodies and parachutes plus supporting models of atmospheres. Terrain and real-time responses of terrain-imaging radar and lidar instruments can also be modeled. The program includes modules for simulation of guidance, navigation, hypersonic steering, and powered descent. Automated state-machine-driven model switching is used to represent spacecraft separations and reconfigurations. Models for computing landing contact and impact forces are expected to be added. DSENDS can be used as a stand-alone program or incorporated into a larger program that simulates operations in real time.

User's guide to resin infusion simulation program in the FORTRAN language

NASA Technical Reports Server (NTRS)

Weideman, Mark H.; Hammond, Vince H.; Loos, Alfred C.

1992-01-01

RTMCL is a user friendly computer code which simulates the manufacture of fabric composites by the resin infusion process. The computer code is based on the process simulation model described in reference 1. Included in the user's guide is a detailed step by step description of how to run the program and enter and modify the input data set. Sample input and output files are included along with an explanation of the results. Finally, a complete listing of the program is provided.

Constructing Cross-Linked Polymer Networks Using Monte Carlo Simulated Annealing Technique for Atomistic Molecular Simulations

DTIC Science & Technology

2014-10-01

the angles and dihedrals that are truly unique will be indicated by the user by editing NewAngleTypesDump and NewDihedralTypesDump. The program ...Atomistic Molecular Simulations 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Robert M Elder, Timothy W Sirk, and...Antechamber program in Assisted Model Building with Energy Refinement (AMBER) Tools to assign partial charges (using the Austin Model 1 [AM1]-bond charge

Validation of Multibody Program to Optimize Simulated Trajectories II Parachute Simulation with Interacting Forces

NASA Technical Reports Server (NTRS)

Raiszadeh, Behzad; Queen, Eric M.; Hotchko, Nathaniel J.

2009-01-01

A capability to simulate trajectories of multiple interacting rigid bodies has been developed, tested and validated. This capability uses the Program to Optimize Simulated Trajectories II (POST 2). The standard version of POST 2 allows trajectory simulation of multiple bodies without force interaction. In the current implementation, the force interaction between the parachute and the suspended bodies has been modeled using flexible lines, allowing accurate trajectory simulation of the individual bodies in flight. The POST 2 multibody capability is intended to be general purpose and applicable to any parachute entry trajectory simulation. This research paper explains the motivation for multibody parachute simulation, discusses implementation methods, and presents validation of this capability.

Flooding Experiments and Modeling for Improved Reactor Safety

DOE Office of Scientific and Technical Information (OSTI.GOV)

Solmos, M.; Hogan, K. J.; Vierow, K.

2008-09-14

Countercurrent two-phase flow and “flooding” phenomena in light water reactor systems are being investigated experimentally and analytically to improve reactor safety of current and future reactors. The aspects that will be better clarified are the effects of condensation and tube inclination on flooding in large diameter tubes. The current project aims to improve the level of understanding of flooding mechanisms and to develop an analysis model for more accurate evaluations of flooding in the pressurizer surge line of a Pressurized Water Reactor (PWR). Interest in flooding has recently increased because Countercurrent Flow Limitation (CCFL) in the AP600 pressurizer surge linemore » can affect the vessel refill rate following a small break LOCA and because analysis of hypothetical severe accidents with the current flooding models in reactor safety codes shows that these models represent the largest uncertainty in analysis of steam generator tube creep rupture. During a hypothetical station blackout without auxiliary feedwater recovery, should the hot leg become voided, the pressurizer liquid will drain to the hot leg and flooding may occur in the surge line. The flooding model heavily influences the pressurizer emptying rate and the potential for surge line structural failure due to overheating and creep rupture. The air-water test results in vertical tubes are presented in this paper along with a semi-empirical correlation for the onset of flooding. The unique aspects of the study include careful experimentation on large-diameter tubes and an integrated program in which air-water testing provides benchmark knowledge and visualization data from which to conduct steam-water testing.« less

Difficulties with True Interoperability in Modeling & Simulation

DTIC Science & Technology

2011-12-01

2009. Programming Scala : Scalability = Functional Programming + Ob- jects. 1 st ed. O‟Reilly Media. 2652 Gallant and Gaughan AUTHOR BIOGRAPHIES...that develops a model or simulation has a specific purpose, set of requirements and limited funding. These programs cannot afford to coordinate with...implementation. The program offices should budget for and plan for coordination across domain projects within a limited scope to improve interoperability with

Medical Team Training Programs in Health Care

DTIC Science & Technology

2005-01-01

simulator-based programs and classroom -based programs. Specifically, we examine the purpose and strategy of each and then review the reported empirical...evidence. In addition, for three of four classroom -based programs we report the results from a series of course observations, curriculum reviews...the-art simulators, whereas others primarily use classroom techniques. Despite these differences, all are heavily inspired by CRM and share the common

Medical Applications of the PHITS Code (3): User Assistance Program for Medical Physics Computation.

PubMed

Furuta, Takuya; Hashimoto, Shintaro; Sato, Tatsuhiko

2016-01-01

DICOM2PHITS and PSFC4PHITS are user assistance programs for medical physics PHITS applications. DICOM2PHITS is a program to construct the voxel PHITS simulation geometry from patient CT DICOM image data by using a conversion table from CT number to material composition. PSFC4PHITS is a program to convert the IAEA phase-space file data to PHITS format to be used as a simulation source of PHITS. Both of the programs are useful for users who want to apply PHITS simulation to verification of the treatment planning of radiation therapy. We are now developing a program to convert dose distribution obtained by PHITS to DICOM RT-dose format. We also want to develop a program which is able to implement treatment information included in other DICOM files (RT-plan and RT-structure) as a future plan.

Central venous catheterization training: current perspectives on the role of simulation

PubMed Central

Soffler, Morgan I; Hayes, Margaret M; Smith, C Christopher

2018-01-01

Simulation is a popular and effective training modality in medical education across a variety of domains. Central venous catheterization (CVC) is commonly undertaken by trainees, and carries significant risk for patient harm when carried out incorrectly. Multiple studies have evaluated the efficacy of simulation-based training programs, in comparison with traditional training modalities, on learner and patient outcomes. In this review, we discuss relevant adult learning principles that support simulation-based CVC training, review the literature on simulation-based CVC training, and highlight the use of simulation-based CVC training programs at various institutions. PMID:29872360

Central venous catheterization training: current perspectives on the role of simulation.

PubMed

Soffler, Morgan I; Hayes, Margaret M; Smith, C Christopher

2018-01-01

Simulation is a popular and effective training modality in medical education across a variety of domains. Central venous catheterization (CVC) is commonly undertaken by trainees, and carries significant risk for patient harm when carried out incorrectly. Multiple studies have evaluated the efficacy of simulation-based training programs, in comparison with traditional training modalities, on learner and patient outcomes. In this review, we discuss relevant adult learning principles that support simulation-based CVC training, review the literature on simulation-based CVC training, and highlight the use of simulation-based CVC training programs at various institutions.

REFLEAK: NIST Leak/Recharge Simulation Program for Refrigerant Mixtures

National Institute of Standards and Technology Data Gateway

SRD 73 NIST REFLEAK: NIST Leak/Recharge Simulation Program for Refrigerant Mixtures (PC database for purchase)   REFLEAK estimates composition changes of zeotropic mixtures in leak and recharge processes.

Validation studies of the DOE-2 Building Energy Simulation Program. Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sullivan, R.; Winkelmann, F.

1998-06-01

This report documents many of the validation studies (Table 1) of the DOE-2 building energy analysis simulation program that have taken place since 1981. Results for several versions of the program are presented with the most recent study conducted in 1996 on version DOE-2.1E and the most distant study conducted in 1981 on version DOE-1.3. This work is part of an effort related to continued development of DOE-2, particularly in its use as a simulation engine for new specialized versions of the program such as the recently released RESFEN 3.1. RESFEN 3.1 is a program specifically dealing with analyzing themore » energy performance of windows in residential buildings. The intent in providing the results of these validation studies is to give potential users of the program a high degree of confidence in the calculated results. Validation studies in which calculated simulation data is compared to measured data have been conducted throughout the development of the DOE-2 program. Discrepancies discovered during the course of such work has resulted in improvements in the simulation algorithms. Table 2 provides a listing of additions and modifications that have been made to various versions of the program since version DOE-2.1A. One of the most significant recent changes in the program occurred with version DOE-2.1E. An improved algorithm for calculating the outside surface film coefficient was implemented. In addition, integration of the WINDOW 4 program was accomplished resulting in improved ability in analyzing window energy performance. Validation and verification of a program as sophisticated as DOE-2 must necessarily be limited because of the approximations inherent in the program. For example, the most accurate model of the heat transfer processes in a building would include a three-dimensional analysis. To justify such detailed algorithmic procedures would correspondingly require detailed information describing the building and/or HVAC system and energy plant parameters. Until building simulation programs can get this data directly from CAD programs, such detail would negate the usefulness of the program for the practicing engineers and architects who currently use the program. In addition, the validation studies discussed herein indicate that such detail is really unnecessary. The comparison of calculated and measured quantities have resulted in a satisfactory level of confidence that is sufficient for continued use of the DOE-2 program. However, additional validation is warranted, particularly at the component level, to further improve the program.« less

European consensus on a competency-based virtual reality training program for basic endoscopic surgical psychomotor skills.

PubMed

van Dongen, Koen W; Ahlberg, Gunnar; Bonavina, Luigi; Carter, Fiona J; Grantcharov, Teodor P; Hyltander, Anders; Schijven, Marlies P; Stefani, Alessandro; van der Zee, David C; Broeders, Ivo A M J

2011-01-01

Virtual reality (VR) simulators have been demonstrated to improve basic psychomotor skills in endoscopic surgery. The exercise configuration settings used for validation in studies published so far are default settings or are based on the personal choice of the tutors. The purpose of this study was to establish consensus on exercise configurations and on a validated training program for a virtual reality simulator, based on the experience of international experts to set criterion levels to construct a proficiency-based training program. A consensus meeting was held with eight European teams, all extensively experienced in using the VR simulator. Construct validity of the training program was tested by 20 experts and 60 novices. The data were analyzed by using the t test for equality of means. Consensus was achieved on training designs, exercise configuration, and examination. Almost all exercises (7/8) showed construct validity. In total, 50 of 94 parameters (53%) showed significant difference. A European, multicenter, validated, training program was constructed according to the general consensus of a large international team with extended experience in virtual reality simulation. Therefore, a proficiency-based training program can be offered to training centers that use this simulator for training in basic psychomotor skills in endoscopic surgery.

Efficient radiologic reading environment by using an open-source macro program as connection software.

PubMed

Lee, Young Han

2012-01-01

The objectives are (1) to introduce an easy open-source macro program as connection software and (2) to illustrate the practical usages in radiologic reading environment by simulating the radiologic reading process. The simulation is a set of radiologic reading process to do a practical task in the radiologic reading room. The principal processes are: (1) to view radiologic images on the Picture Archiving and Communicating System (PACS), (2) to connect the HIS/EMR (Hospital Information System/Electronic Medical Record) system, (3) to make an automatic radiologic reporting system, and (4) to record and recall information of interesting cases. This simulation environment was designed by using open-source macro program as connection software. The simulation performed well on the Window-based PACS workstation. Radiologists practiced the steps of the simulation comfortably by utilizing the macro-powered radiologic environment. This macro program could automate several manual cumbersome steps in the radiologic reading process. This program successfully acts as connection software for the PACS software, EMR/HIS, spreadsheet, and other various input devices in the radiologic reading environment. A user-friendly efficient radiologic reading environment could be established by utilizing open-source macro program as connection software. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

SIMPSON: a general simulation program for solid-state NMR spectroscopy.

PubMed

Bak, M; Rasmussen, J T; Nielsen, N C

2000-12-01

A computer program for fast and accurate numerical simulation of solid-state NMR experiments is described. The program is designed to emulate a NMR spectrometer by letting the user specify high-level NMR concepts such as spin systems, nuclear spin interactions, RF irradiation, free precession, phase cycling, coherence-order filtering, and implicit/explicit acquisition. These elements are implemented using the Tcl scripting language to ensure a minimum of programming overhead and direct interpretation without the need for compilation, while maintaining the flexibility of a full-featured programming language. Basically, there are no intrinsic limitations to the number of spins, types of interactions, sample conditions (static or spinning, powders, uniaxially oriented molecules, single crystals, or solutions), and the complexity or number of spectral dimensions for the pulse sequence. The applicability ranges from simple 1D experiments to advanced multiple-pulse and multiple-dimensional experiments, series of simulations, parameter scans, complex data manipulation/visualization, and iterative fitting of simulated to experimental spectra. A major effort has been devoted to optimizing the computation speed using state-of-the-art algorithms for the time-consuming parts of the calculations implemented in the core of the program using the C programming language. Modification and maintenance of the program are facilitated by releasing the program as open source software (General Public License) currently at http://nmr.imsb.au.dk. The general features of the program are demonstrated by numerical simulations of various aspects for REDOR, rotational resonance, DRAMA, DRAWS, HORROR, C7, TEDOR, POST-C7, CW decoupling, TPPM, F-SLG, SLF, SEMA-CP, PISEMA, RFDR, QCPMG-MAS, and MQ-MAS experiments. Copyright 2000 Academic Press.

Mission simulator test data. [an overview of a real time mission simulation test program of a nickel cadmium battery

NASA Technical Reports Server (NTRS)

Hendee, E. A.

1980-01-01

A real time mission simulation test program of nickel cadmium cells, performed in conjunction with the Anik 1A2 satellite, is reviewed. Simulation of the temperature profiles, the electrical profiles, the depth of discharge, and the rate of charge and discharge is reported. The type of separator used in the cells and the transfer of electrolytes during overcharge are discussed.

Strategic Mobility 21: Modeling, Simulation, and Analysis

DTIC Science & Technology

2010-04-14

using AnyLogic , which is a Java programmed, multi-method simulation modeling tool developed by XJ Technologies. The last section examines the academic... simulation model from an Arena platform to an AnyLogic based Web Service. MATLAB is useful for small problems with few nodes, but GAMS/CPLEX is better... Transportation Modeling Studio TM . The SCASN modeling and simulation program was designed to be generic in nature to allow for use by both commercial and

Trajectory Reconstruction Program Milestone 2/3 Report. Volume 1. Description and Overview

DTIC Science & Technology

1974-12-16

Simulation Data Generation Missile Trajectory Error Analysis Modularized Program Guidance and Targeting Multiple Vehicle Simulation IBM 360/370 Numerical...consists of vehicle simulation subprograms designed and written in FORTRAN for CDC 6600/7600, IBM 360/370, and UNIVAC 1108/1110 series computers. The o-erall...vehicle simulation subprograms designed and written in FORTRAN fcr CDC 6600/7600, IBM 360/370, and UNIVAC l08/1110 series computers. The overall

NVSIM: UNIX-based thermal imaging system simulator

NASA Astrophysics Data System (ADS)

Horger, John D.

1993-08-01

For several years the Night Vision and Electronic Sensors Directorate (NVESD) has been using an internally developed forward looking infrared (FLIR) simulation program. In response to interest in the simulation part of these projects by other organizations, NVESD has been working on a new version of the simulation, NVSIM, that will be made generally available to the FLIR using community. NVSIM uses basic FLIR specification data, high resolution thermal input imagery and spatial domain image processing techniques to produce simulated image outputs from a broad variety of FLIRs. It is being built around modular programming techniques to allow simpler addition of more sensor effects. The modularity also allows selective inclusion and exclusion of individual sensor effects at run time. The simulation has been written in the industry standard ANSI C programming language under the widely used UNIX operating system to make it easily portable to a wide variety of computer platforms.

RENEW v3.2 user's manual, maintenance estimation simulation for Space Station Freedom Program

NASA Technical Reports Server (NTRS)

Bream, Bruce L.

1993-01-01

RENEW is a maintenance event estimation simulation program developed in support of the Space Station Freedom Program (SSFP). This simulation uses reliability and maintainability (R&M) and logistics data to estimate both average and time dependent maintenance demands. The simulation uses Monte Carlo techniques to generate failure and repair times as a function of the R&M and logistics parameters. The estimates are generated for a single type of orbital replacement unit (ORU). The simulation has been in use by the SSFP Work Package 4 prime contractor, Rocketdyne, since January 1991. The RENEW simulation gives closer estimates of performance since it uses a time dependent approach and depicts more factors affecting ORU failure and repair than steady state average calculations. RENEW gives both average and time dependent demand values. Graphs of failures over the mission period and yearly failure occurrences are generated. The averages demand rate for the ORU over the mission period is also calculated. While RENEW displays the results in graphs, the results are also available in a data file for further use by spreadsheets or other programs. The process of using RENEW starts with keyboard entry of the R&M and operational data. Once entered, the data may be saved in a data file for later retrieval. The parameters may be viewed and changed after entry using RENEW. The simulation program runs the number of Monte Carlo simulations requested by the operator. Plots and tables of the results can be viewed on the screen or sent to a printer. The results of the simulation are saved along with the input data. Help screens are provided with each menu and data entry screen.

Design and evaluation of simulation scenarios for a program introducing patient safety, teamwork, safety leadership, and simulation to healthcare leaders and managers.

PubMed

Cooper, Jeffrey B; Singer, Sara J; Hayes, Jennifer; Sales, Michael; Vogt, Jay W; Raemer, Daniel; Meyer, Gregg S

2011-08-01

We developed a training program to introduce managers and informal leaders of healthcare organizations to key concepts of teamwork, safety leadership, and simulation to motivate them to act as leaders to improve safety within their sphere of influence. This report describes the simulation scenario and debriefing that are core elements of that program. Twelve teams of clinician and nonclinician managers were selected from a larger set of volunteers to participate in a 1-day, multielement training program. Two simulation exercises were developed: one for teams of nonclinicians and the other for clinicians or mixed groups. The scenarios represented two different clinical situations, each designed to engage participants in discussions of their safety leadership and teamwork issues immediately after the experience. In the scenarios for nonclinicians, participants conducted an anesthetic induction and then managed an ethical situation. The scenario for clinicians simulated a consulting visit to an emergency room that evolved into a problem-solving challenge. Participants in this scenario had a limited time to prepare advice for hospital leadership on how to improve observed safety and cultural deficiencies. Debriefings after both types of scenarios were conducted using principles of "debriefing with good judgment." We assessed the relevance and impact of the program by analyzing participant reactions to the simulation through transcript data and facilitator observations as well as a postcourse questionnaire. The teams generally reported positive perceptions of the relevance and quality of the simulation with varying types and degrees of impact on their leadership and teamwork behaviors. These kinds of clinical simulation exercises can be used to teach healthcare leaders and managers safety leadership and teamwork skills and behaviors.

A simulation exercise of a cavity-type solar receiver using the HEAP program

NASA Technical Reports Server (NTRS)

Lansing, F. L.

1979-01-01

A computer program has been developed at JPL to support the advanced studies of solar receivers in high concentration solar-thermal-electric power plants. This work presents briefly the program methodology, input data required, expected output results, capabilities and limitations. The program was used to simulate an existing 5 kwt experimental receiver of a cavity type. The receiver is located at the focus of a paraboloid dish and is connected to a Stirling engine. Both steady state and transient performance simulation were given. Details about the receiver modeling were also presented to illustrate the procedure followed. Simulated temperature patterns were found in good agreement with test data obtained by high temperature thermocouples. The simulated receiver performance was extrapolated to various operating conditions not attained experimentally. The results of the parameterization study were fitted to a general performance expression to determine the receiver characteristic constraints. The latter were used to optimize the receiver operating conditions to obtain the highest overall conversion efficiency.

Computer simulation program for medium-energy ion scattering and Rutherford backscattering spectrometry

NASA Astrophysics Data System (ADS)

Nishimura, Tomoaki

2016-03-01

A computer simulation program for ion scattering and its graphical user interface (MEISwin) has been developed. Using this program, researchers have analyzed medium-energy ion scattering and Rutherford backscattering spectrometry at Ritsumeikan University since 1998, and at Rutgers University since 2007. The main features of the program are as follows: (1) stopping power can be chosen from five datasets spanning several decades (from 1977 to 2011), (2) straggling can be chosen from two datasets, (3) spectral shape can be selected as Gaussian or exponentially modified Gaussian, (4) scattering cross sections can be selected as Coulomb or screened, (5) simulations adopt the resonant elastic scattering cross section of 16O(4He, 4He)16O, (6) pileup simulation for RBS spectra is supported, (7) natural and specific isotope abundances are supported, and (8) the charge fraction can be chosen from three patterns (fixed, energy-dependent, and ion fraction with charge-exchange parameters for medium-energy ion scattering). This study demonstrates and discusses the simulations and their results.

[Training of residents in obstetrics and gynecology: Assessment of an educational program including formal lectures and practical sessions using simulators].

PubMed

Jordan, A; El Haloui, O; Breaud, J; Chevalier, D; Antomarchi, J; Bongain, A; Boucoiran, I; Delotte, J

2015-01-01

Evaluate an educational program in the training of residents in gynecology-obstetrics (GO) with a theory session and a practical session on simulators and analyze their learning curve. Single-center prospective study, at the university hospital (CHU). Two-day sessions were leaded in April and July 2013. An evaluation on obstetric and gynecological surgery simulator was available to all residents. Theoretical knowledge principles of obstetrics were evaluated early in the session and after formal lectures was taught to them. At the end of the first session, a satisfaction questionnaire was distributed to all participants. Twenty residents agreed to participate to the training sessions. Evaluation of theoretical knowledge: at the end of the session, the residents obtained a significant improvement in their score on 20 testing knowledge. Obstetrical simulator: a statistically significant improvement in scores on assessments simulator vaginal delivery between the first and second session. Subjectively, a larger increase feeling was seen after breech delivery simulation than for the cephalic vaginal delivery. However, the confidence level of the resident after breech delivery simulation has not been improved at the end of the second session. Simulation in gynecological surgery: a trend towards improvement in the time realized on the peg-transfer between the two sessions was noted. In the virtual simulation, no statistically significant differences showed, no improvement for in salpingectomy's time. Subjectively, the residents felt an increase in the precision of their gesture. Satisfaction: All residents have tried the whole program. They considered the pursuit of these sessions on simulators was necessary and even mandatory. The approach chosen by this structured educational program allowed a progression for the residents, both objectively and subjectively. This simulation program type for the resident's training would use this tool in assessing their skills and develop learning curves. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

CHARMM-GUI Input Generator for NAMD, GROMACS, AMBER, OpenMM, and CHARMM/OpenMM Simulations Using the CHARMM36 Additive Force Field

DOE PAGES

Lee, Jumin; Cheng, Xi; Swails, Jason M.; ...

2015-11-12

Here we report that proper treatment of nonbonded interactions is essential for the accuracy of molecular dynamics (MD) simulations, especially in studies of lipid bilayers. The use of the CHARMM36 force field (C36 FF) in different MD simulation programs can result in disagreements with published simulations performed with CHARMM due to differences in the protocols used to treat the long-range and 1-4 nonbonded interactions. In this study, we systematically test the use of the C36 lipid FF in NAMD, GROMACS, AMBER, OpenMM, and CHARMM/OpenMM. A wide range of Lennard-Jones (LJ) cutoff schemes and integrator algorithms were tested to find themore » optimal simulation protocol to best match bilayer properties of six lipids with varying acyl chain saturation and head groups. MD simulations of a 1,2-dipalmitoyl-sn-phosphatidylcholine (DPPC) bilayer were used to obtain the optimal protocol for each program. MD simulations with all programs were found to reasonably match the DPPC bilayer properties (surface area per lipid, chain order parameters, and area compressibility modulus) obtained using the standard protocol used in CHARMM as well as from experiments. The optimal simulation protocol was then applied to the other five lipid simulations and resulted in excellent agreement between results from most simulation programs as well as with experimental data. AMBER compared least favorably with the expected membrane properties, which appears to be due to its use of the hard-truncation in the LJ potential versus a force-based switching function used to smooth the LJ potential as it approaches the cutoff distance. The optimal simulation protocol for each program has been implemented in CHARMM-GUI. This protocol is expected to be applicable to the remainder of the additive C36 FF including the proteins, nucleic acids, carbohydrates, and small molecules.« less

CHARMM-GUI Input Generator for NAMD, GROMACS, AMBER, OpenMM, and CHARMM/OpenMM Simulations Using the CHARMM36 Additive Force Field.

PubMed

Lee, Jumin; Cheng, Xi; Swails, Jason M; Yeom, Min Sun; Eastman, Peter K; Lemkul, Justin A; Wei, Shuai; Buckner, Joshua; Jeong, Jong Cheol; Qi, Yifei; Jo, Sunhwan; Pande, Vijay S; Case, David A; Brooks, Charles L; MacKerell, Alexander D; Klauda, Jeffery B; Im, Wonpil

2016-01-12

Proper treatment of nonbonded interactions is essential for the accuracy of molecular dynamics (MD) simulations, especially in studies of lipid bilayers. The use of the CHARMM36 force field (C36 FF) in different MD simulation programs can result in disagreements with published simulations performed with CHARMM due to differences in the protocols used to treat the long-range and 1-4 nonbonded interactions. In this study, we systematically test the use of the C36 lipid FF in NAMD, GROMACS, AMBER, OpenMM, and CHARMM/OpenMM. A wide range of Lennard-Jones (LJ) cutoff schemes and integrator algorithms were tested to find the optimal simulation protocol to best match bilayer properties of six lipids with varying acyl chain saturation and head groups. MD simulations of a 1,2-dipalmitoyl-sn-phosphatidylcholine (DPPC) bilayer were used to obtain the optimal protocol for each program. MD simulations with all programs were found to reasonably match the DPPC bilayer properties (surface area per lipid, chain order parameters, and area compressibility modulus) obtained using the standard protocol used in CHARMM as well as from experiments. The optimal simulation protocol was then applied to the other five lipid simulations and resulted in excellent agreement between results from most simulation programs as well as with experimental data. AMBER compared least favorably with the expected membrane properties, which appears to be due to its use of the hard-truncation in the LJ potential versus a force-based switching function used to smooth the LJ potential as it approaches the cutoff distance. The optimal simulation protocol for each program has been implemented in CHARMM-GUI. This protocol is expected to be applicable to the remainder of the additive C36 FF including the proteins, nucleic acids, carbohydrates, and small molecules.

REFERENCE MANUAL FOR RASSMIT VERSION 2.1: SUB-SLAB DEPRESSURIZATION SYSTEM DESIGN PERFORMANCE SIMULATION PROGRAM

EPA Science Inventory

The report is a reference manual for RASSMlT Version 2.1, a computer program that was developed to simulate and aid in the design of sub-slab depressurization systems used for indoor radon mitigation. The program was designed to run on DOS-compatible personal computers to ensure ...

Enhancements to the Image Analysis Tool for Core Punch Experiments and Simulations (vs. 2014)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hogden, John Edward; Unal, Cetin

A previous paper (Hogden & Unal, 2012, Image Analysis Tool for Core Punch Experiments and Simulations) described an image processing computer program developed at Los Alamos National Laboratory. This program has proven useful so developement has been continued. In this paper we describe enhacements to the program as of 2014.

A Microcomputer Program that Simulates the Baumol-Tobin Transactions Demand for Money.

ERIC Educational Resources Information Center

Beckman, Steven

1987-01-01

This article describes an economic model dealing with the demand for money and a microcomputer program which enables students to experiment with cash management techniques. By simulating personal experiences, the program teaches how changes in income, interest rates, and charges for exchanging bonds and cash affect money demand. (Author/JDH)

Payload IVA training and simulation

NASA Technical Reports Server (NTRS)

Monsees, J. H.

1982-01-01

The development of a training program for the intravehicular operation of space shuttle payloads is discussed. The priorities for the program are compliance with established training standards, and accommodating changes. Simulation devices are also reviewed.

PyNN: A Common Interface for Neuronal Network Simulators.

PubMed

Davison, Andrew P; Brüderle, Daniel; Eppler, Jochen; Kremkow, Jens; Muller, Eilif; Pecevski, Dejan; Perrinet, Laurent; Yger, Pierre

2008-01-01

Computational neuroscience has produced a diversity of software for simulations of networks of spiking neurons, with both negative and positive consequences. On the one hand, each simulator uses its own programming or configuration language, leading to considerable difficulty in porting models from one simulator to another. This impedes communication between investigators and makes it harder to reproduce and build on the work of others. On the other hand, simulation results can be cross-checked between different simulators, giving greater confidence in their correctness, and each simulator has different optimizations, so the most appropriate simulator can be chosen for a given modelling task. A common programming interface to multiple simulators would reduce or eliminate the problems of simulator diversity while retaining the benefits. PyNN is such an interface, making it possible to write a simulation script once, using the Python programming language, and run it without modification on any supported simulator (currently NEURON, NEST, PCSIM, Brian and the Heidelberg VLSI neuromorphic hardware). PyNN increases the productivity of neuronal network modelling by providing high-level abstraction, by promoting code sharing and reuse, and by providing a foundation for simulator-agnostic analysis, visualization and data-management tools. PyNN increases the reliability of modelling studies by making it much easier to check results on multiple simulators. PyNN is open-source software and is available from http://neuralensemble.org/PyNN.

PyNN: A Common Interface for Neuronal Network Simulators

PubMed Central

Davison, Andrew P.; Brüderle, Daniel; Eppler, Jochen; Kremkow, Jens; Muller, Eilif; Pecevski, Dejan; Perrinet, Laurent; Yger, Pierre

2008-01-01

Computational neuroscience has produced a diversity of software for simulations of networks of spiking neurons, with both negative and positive consequences. On the one hand, each simulator uses its own programming or configuration language, leading to considerable difficulty in porting models from one simulator to another. This impedes communication between investigators and makes it harder to reproduce and build on the work of others. On the other hand, simulation results can be cross-checked between different simulators, giving greater confidence in their correctness, and each simulator has different optimizations, so the most appropriate simulator can be chosen for a given modelling task. A common programming interface to multiple simulators would reduce or eliminate the problems of simulator diversity while retaining the benefits. PyNN is such an interface, making it possible to write a simulation script once, using the Python programming language, and run it without modification on any supported simulator (currently NEURON, NEST, PCSIM, Brian and the Heidelberg VLSI neuromorphic hardware). PyNN increases the productivity of neuronal network modelling by providing high-level abstraction, by promoting code sharing and reuse, and by providing a foundation for simulator-agnostic analysis, visualization and data-management tools. PyNN increases the reliability of modelling studies by making it much easier to check results on multiple simulators. PyNN is open-source software and is available from http://neuralensemble.org/PyNN. PMID:19194529

Simulation and animation of sensor-driven robots.

PubMed

Chen, C; Trivedi, M M; Bidlack, C R

1994-10-01

Most simulation and animation systems utilized in robotics are concerned with simulation of the robot and its environment without simulation of sensors. These systems have difficulty in handling robots that utilize sensory feedback in their operation. In this paper, a new design of an environment for simulation, animation, and visualization of sensor-driven robots is presented. As sensor technology advances, increasing numbers of robots are equipped with various types of sophisticated sensors. The main goal of creating the visualization environment is to aid the automatic robot programming and off-line programming capabilities of sensor-driven robots. The software system will help the users visualize the motion and reaction of the sensor-driven robot under their control program. Therefore, the efficiency of the software development is increased, the reliability of the software and the operation safety of the robot are ensured, and the cost of new software development is reduced. Conventional computer-graphics-based robot simulation and animation software packages lack of capabilities for robot sensing simulation. This paper describes a system designed to overcome this deficiency.

T-H-A-T-S: timber-harvesting-and-transport-simulator: with subroutines for Appalachian logging

Treesearch

A. Jeff Martin

1975-01-01

A computer program for simulating harvesting operations is presented. Written in FORTRAN IV, the program contains subroutines that were developed for Appalachian logging conditions. However, with appropriate modifications, the simulator would be applicable for most logging operations and locations. The details of model development and its methodology are presented,...

Doing Poverty: Learning Outcomes among Students Participating in the Community Action Poverty Simulation Program

ERIC Educational Resources Information Center

Steck, Laura West; Engler, Jennifer N.; Ligon, Mary; Druen, Perri B.; Cosgrove, Erin

2011-01-01

This article discusses an application of the Lewinian/Kolb experiential learning model in the context of undergraduate participation in the Missouri Community Action Poverty Simulation (CAPS) program. CAPS is designed to simulate common, everyday experiences among people living in poverty as participants take on the roles of family members working…

A Digital Simulation Program for Health Science Students to Follow Drug Levels in the Body

ERIC Educational Resources Information Center

Stavchansky, Salomon; And Others

1977-01-01

The Rayetheon Scientific Simulation Language (RSSL) program, an easily-used simulation on the CDC/6600 computer at the University of Texas at Austin, offers a simple method of solving differential equations on a digital computer. It is used by undergraduate biopharmaceutics-pharmacokinetics students and graduate students in all areas. (Author/LBH)

An Investigation of the Effectiveness of Computer Simulation Programs as Tutorial Tools for Teaching Population Ecology at University.

ERIC Educational Resources Information Center

Korfiatis, K.; Papatheodorou, E.; Paraskevopoulous, S.; Stamou, G. P.

1999-01-01

Describes a study of the effectiveness of computer-simulation programs in enhancing biology students' familiarity with ecological modeling and concepts. Finds that computer simulations improved student comprehension of ecological processes expressed in mathematical form, but did not allow a full understanding of ecological concepts. Contains 28…

Future directions in flight simulation: A user perspective

NASA Technical Reports Server (NTRS)

Jackson, Bruce

1993-01-01

Langley Research Center was an early leader in simulation technology, including a special emphasis in space vehicle simulations such as the rendezvous and docking simulator for the Gemini program and the lunar landing simulator used before Apollo. In more recent times, Langley operated the first synergistic six degree of freedom motion platform (the Visual Motion Simulator, or VMS) and developed the first dual-dome air combat simulator, the Differential Maneuvering Simulator (DMS). Each Langley simulator was developed more or less independently from one another with different programming support. At present time, the various simulation cockpits, while supported by the same host computer system, run dissimilar software. The majority of recent investments in Langley's simulation facilities have been hardware procurements: host processors, visual systems, and most recently, an improved motion system. Investments in software improvements, however, have not been of the same order.

Analysis of Plane-Parallel Electron Beam Propagation in Different Media by Numerical Simulation Methods

NASA Astrophysics Data System (ADS)

Miloichikova, I. A.; Bespalov, V. I.; Krasnykh, A. A.; Stuchebrov, S. G.; Cherepennikov, Yu. M.; Dusaev, R. R.

2018-04-01

Simulation by the Monte Carlo method is widely used to calculate the character of ionizing radiation interaction with substance. A wide variety of programs based on the given method allows users to choose the most suitable package for solving computational problems. In turn, it is important to know exactly restrictions of numerical systems to avoid gross errors. Results of estimation of the feasibility of application of the program PCLab (Computer Laboratory, version 9.9) for numerical simulation of the electron energy distribution absorbed in beryllium, aluminum, gold, and water for industrial, research, and clinical beams are presented. The data obtained using programs ITS and Geant4 being the most popular software packages for solving the given problems and the program PCLab are presented in the graphic form. A comparison and an analysis of the results obtained demonstrate the feasibility of application of the program PCLab for simulation of the absorbed energy distribution and dose of electrons in various materials for energies in the range 1-20 MeV.

Programs for Testing Processor-in-Memory Computing Systems

NASA Technical Reports Server (NTRS)

Katz, Daniel S.

2006-01-01

The Multithreaded Microbenchmarks for Processor-In-Memory (PIM) Compilers, Simulators, and Hardware are computer programs arranged in a series for use in testing the performances of PIM computing systems, including compilers, simulators, and hardware. The programs at the beginning of the series test basic functionality; the programs at subsequent positions in the series test increasingly complex functionality. The programs are intended to be used while designing a PIM system, and can be used to verify that compilers, simulators, and hardware work correctly. The programs can also be used to enable designers of these system components to examine tradeoffs in implementation. Finally, these programs can be run on non-PIM hardware (either single-threaded or multithreaded) using the POSIX pthreads standard to verify that the benchmarks themselves operate correctly. [POSIX (Portable Operating System Interface for UNIX) is a set of standards that define how programs and operating systems interact with each other. pthreads is a library of pre-emptive thread routines that comply with one of the POSIX standards.

Implementation and evaluation of a simulation curriculum for paediatric residency programs including just-in-time in situ mock codes

PubMed Central

Sam, Jonathan; Pierse, Michael; Al-Qahtani, Abdullah; Cheng, Adam

2012-01-01

OBJECTIVE: To develop, implement and evaluate a simulation-based acute care curriculum in a paediatric residency program using an integrated and longitudinal approach. DESIGN: Curriculum framework consisting of three modular, year-specific courses and longitudinal just-in-time, in situ mock codes. SETTING: Paediatric residency program at BC Children’s Hospital, Vancouver, British Columbia. INTERVENTIONS: The three year-specific courses focused on the critical first 5 min, complex medical management and crisis resource management, respectively. The just-in-time in situ mock codes simulated the acute deterioration of an existing ward patient, prepared the actual multidisciplinary code team, and primed the surrounding crisis support systems. Each curriculum component was evaluated with surveys using a five-point Likert scale. RESULTS: A total of 40 resident surveys were completed after each of the modular courses, and an additional 28 surveys were completed for the overall simulation curriculum. The highest Likert scores were for hands-on skill stations, immersive simulation environment and crisis resource management teaching. Survey results also suggested that just-in-time mock codes were realistic, reinforced learning, and prepared ward teams for patient deterioration. CONCLUSIONS: A simulation-based acute care curriculum was successfully integrated into a paediatric residency program. It provides a model for integrating simulation-based learning into other training programs, as well as a model for any hospital that wishes to improve paediatric resuscitation outcomes using just-in-time in situ mock codes. PMID:23372405

Spacecraft orbit/earth scan derivations, associated APL program, and application to IMP-6

NASA Technical Reports Server (NTRS)

Smith, G. A.

1971-01-01

The derivation of a time shared, remote site, demand processed computer program is discussed. The computer program analyzes the effects of selected orbit, attitude, and spacecraft parameters on earth sensor detections of earth. For prelaunch analysis, the program may be used to simulate effects in nominal parameters which are used in preparing attitude data processing programs. After launch, comparison of results from a simulation and from satellite data will produce deviations helpful in isolating problems.

From bricks to buildings: adapting the Medical Research Council framework to develop programs of research in simulation education and training for the health professions.

PubMed

Haji, Faizal A; Da Silva, Celina; Daigle, Delton T; Dubrowski, Adam

2014-08-01

Presently, health care simulation research is largely conducted on a study-by-study basis. Although such "project-based" research generates a plethora of evidence, it can be chaotic and contradictory. A move toward sustained, thematic, theory-based programs of research is necessary to advance knowledge in the field. Recognizing that simulation is a complex intervention, we present a framework for developing research programs in simulation-based education adapted from the Medical Research Council (MRC) guidance. This framework calls for an iterative approach to developing, refining, evaluating, and implementing simulation interventions. The adapted framework guidance emphasizes: (1) identification of theory and existing evidence; (2) modeling and piloting interventions to clarify active ingredients and identify mechanisms linking the context, intervention, and outcomes; and (3) evaluation of intervention processes and outcomes in both the laboratory and real-world setting. The proposed framework will aid simulation researchers in developing more robust interventions that optimize simulation-based education and advance our understanding of simulation pedagogy.

Simulating a Direction-Finder Search for an ELT

NASA Technical Reports Server (NTRS)

Bream, Bruce

2005-01-01

A computer program simulates the operation of direction-finding equipment engaged in a search for an emergency locator transmitter (ELT) aboard an aircraft that has crashed. The simulated equipment is patterned after the equipment used by the Civil Air Patrol to search for missing aircraft. The program is designed to be used for training in radio direction-finding and/or searching for missing aircraft without incurring the expense and risk of using real aircraft and ground search resources. The program places a hidden ELT on a map and enables the user to search for the location of the ELT by moving a 14 NASA Tech Briefs, March 2005 small aircraft image around the map while observing signal-strength and direction readings on a simulated direction- finding locator instrument. As the simulated aircraft is turned and moved on the map, the program updates the readings on the direction-finding instrument to reflect the current position and heading of the aircraft relative to the location of the ELT. The software is distributed in a zip file that contains an installation program. The software runs on the Microsoft Windows 9x, NT, and XP operating systems.

Simulation of root forms using cellular automata model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Winarno, Nanang, E-mail: nanang-winarno@upi.edu; Prima, Eka Cahya; Afifah, Ratih Mega Ayu

This research aims to produce a simulation program for root forms using cellular automata model. Stephen Wolfram in his book entitled “A New Kind of Science” discusses the formation rules based on the statistical analysis. In accordance with Stephen Wolfram’s investigation, the research will develop a basic idea of computer program using Delphi 7 programming language. To best of our knowledge, there is no previous research developing a simulation describing root forms using the cellular automata model compared to the natural root form with the presence of stone addition as the disturbance. The result shows that (1) the simulation usedmore » four rules comparing results of the program towards the natural photographs and each rule had shown different root forms; (2) the stone disturbances prevent the root growth and the multiplication of root forms had been successfully modeled. Therefore, this research had added some stones, which have size of 120 cells placed randomly in the soil. Like in nature, stones cannot be penetrated by plant roots. The result showed that it is very likely to further develop the program of simulating root forms by 50 variations.« less

MPPhys—A many-particle simulation package for computational physics education

NASA Astrophysics Data System (ADS)

Müller, Thomas

2014-03-01

In a first course to classical mechanics elementary physical processes like elastic two-body collisions, the mass-spring model, or the gravitational two-body problem are discussed in detail. The continuation to many-body systems, however, is deferred to graduate courses although the underlying equations of motion are essentially the same and although there is a strong motivation for high-school students in particular because of the use of particle systems in computer games. The missing link between the simple and the more complex problem is a basic introduction to solve the equations of motion numerically which could be illustrated, however, by means of the Euler method. The many-particle physics simulation package MPPhys offers a platform to experiment with simple particle simulations. The aim is to give a principle idea how to implement many-particle simulations and how simulation and visualization can be combined for interactive visual explorations. Catalogue identifier: AERR_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AERR_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 111327 No. of bytes in distributed program, including test data, etc.: 608411 Distribution format: tar.gz Programming language: C++, OpenGL, GLSL, OpenCL. Computer: Linux and Windows platforms with OpenGL support. Operating system: Linux and Windows. RAM: Source Code 4.5 MB Complete package 242 MB Classification: 14, 16.9. External routines: OpenGL, OpenCL Nature of problem: Integrate N-body simulations, mass-spring models Solution method: Numerical integration of N-body-simulations, 3D-Rendering via OpenGL. Running time: Problem dependent

Note on the artefacts in SRIM simulation of sputtering

NASA Astrophysics Data System (ADS)

Shulga, V. I.

2018-05-01

The computer simulation program SRIM, unlike other well-known programs (MARLOWE, TRIM.SP, etc.), predicts non-zero values of the sputter yield at glancing ion bombardment of smooth amorphous targets and, for heavy ions, greatly underestimates the sputter yield at normal incidence. To understand the reasons for this, the sputtering of amorphous silicon bombarded with different ions was modeled here using the author's program OKSANA. Most simulations refer to 1 keV Xe ions, and angles of incidence cover range from 0 (normal incidence) to almost 90°. It has been shown that SRIM improperly simulates the initial stage of the sputtering process. Some other artefacts in SRIM calculations of sputtering are also revealed and discussed.

Teaching Microbial Growth by Simulation.

ERIC Educational Resources Information Center

Ruiz, A. Fernandez; And Others

1989-01-01

Presented is a simulation program for Apple II computer which assays the effects of a series of variables on bacterial growth and interactions between microbial populations. Results of evaluation of the program with students are summarized. (CW)

MINEXP, A Computer-Simulated Mineral Exploration Program

ERIC Educational Resources Information Center

Smith, Michael J.; And Others

1978-01-01

This computer simulation is designed to put students into a realistic decision making situation in mineral exploration. This program can be used with different exploration situations such as ore deposits, petroleum, ground water, etc. (MR)

Turbulence simulation mechanization for Space Shuttle Orbiter dynamics and control studies

NASA Technical Reports Server (NTRS)

Tatom, F. B.; King, R. L.

1977-01-01

The current version of the NASA turbulent simulation model in the form of a digital computer program, TBMOD, is described. The logic of the program is discussed and all inputs and outputs are defined. An alternate method of shear simulation suitable for incorporation into the model is presented. The simulation is based on a von Karman spectrum and the assumption of isotropy. The resulting spectral density functions for the shear model are included.

Simulation validation of the XV-15 tilt-rotor research aircraft

NASA Technical Reports Server (NTRS)

Ferguson, S. W.; Hanson, G. D.; Churchill, G. B.

1984-01-01

The results of a simulation validation program of the XV-15 tilt-rotor research aircraft are detailed, covering such simulation aspects as the mathematical model, visual system, motion system, cab aural system, cab control loader system, pilot perceptual fidelity, and generic tilt rotor applications. Simulation validation was performed for the hover, low-speed, and sideward flight modes, with consideration of the in-ground rotor effect. Several deficiencies of the mathematical model and the simulation systems were identified in the course of the simulation validation project, and some were corrected. It is noted that NASA's Vertical Motion Simulator used in the program is an excellent tool for tilt-rotor and rotorcraft design, development, and pilot training.

A pharmacy business management simulation exercise as a practical application of business management material and principles.

PubMed

Rollins, Brent L; Gunturi, Rahul; Sullivan, Donald

2014-04-17

To implement a pharmacy business management simulation exercise as a practical application of business management material and principles and assess students' perceived value. As part of a pharmacy management and administration course, students made various calculations and management decisions in the global categories of hours of operation, inventory, pricing, and personnel. The students entered the data into simulation software and a realistic community pharmacy marketplace was modeled. Course topics included accounting, economics, finance, human resources, management, marketing, and leadership. An 18-item posttest survey was administered. Students' slightly to moderately agreed the pharmacy simulation program enhanced their knowledge and understanding, particularly of inventory management, cash flow statements, balance sheets, and income statements. Overall attitudes toward the pharmacy simulation program were also slightly positive and students also slightly agreed the pharmacy simulation program enhanced their learning of pharmacy business management. Inventory management was the only area in which students felt they had at least "some" exposure to the assessed business management topics during IPPEs/internship, while all other areas of experience ranged from "not at all" to "a little." The pharmacy simulation program is an effective active-learning exercise and enhanced students' knowledge and understanding of the business management topics covered.

A Pharmacy Business Management Simulation Exercise as a Practical Application of Business Management Material and Principles

PubMed Central

Rollins, Brent L.; Gunturi, Rahul; Sullivan, Donald

2014-01-01

Objective. To implement a pharmacy business management simulation exercise as a practical application of business management material and principles and assess students’ perceived value. Design. As part of a pharmacy management and administration course, students made various calculations and management decisions in the global categories of hours of operation, inventory, pricing, and personnel. The students entered the data into simulation software and a realistic community pharmacy marketplace was modeled. Course topics included accounting, economics, finance, human resources, management, marketing, and leadership. Assessment. An 18-item posttest survey was administered. Students’ slightly to moderately agreed the pharmacy simulation program enhanced their knowledge and understanding, particularly of inventory management, cash flow statements, balance sheets, and income statements. Overall attitudes toward the pharmacy simulation program were also slightly positive and students also slightly agreed the pharmacy simulation program enhanced their learning of pharmacy business management. Inventory management was the only area in which students felt they had at least “some” exposure to the assessed business management topics during IPPEs/internship, while all other areas of experience ranged from “not at all” to “a little.” Conclusion. The pharmacy simulation program is an effective active-learning exercise and enhanced students’ knowledge and understanding of the business management topics covered. PMID:24761023

Organizational culture shapes the adoption and incorporation of simulation into nursing curricula: a grounded theory study.

PubMed

Taplay, Karyn; Jack, Susan M; Baxter, Pamela; Eva, Kevin; Martin, Lynn

2014-01-01

Purpose. To create a substantive mid-range theory explaining how the organizational cultures of undergraduate nursing programs shape the adoption and incorporation of mid-to high-level technical fidelity simulators as a teaching strategy within curricula. Method. A constructivist grounded theory was used to guide this study which was conducted in Ontario, Canada, during 2011-12. Semistructured interviews (n = 43) with participants that included nursing administrators, nursing faculty, and simulation leaders across multiple programs (n = 13) informed this study. Additionally, key documents (n = 67) were reviewed. Purposeful and theoretical sampling was used and data were collected and analyzed simultaneously. Data were compared among and between sites. Findings. The organizational elements that shape simulation in nursing (OESSN) model depicts five key organizational factors at the nursing program level that shaped the adoption and incorporation of simulation: (1) leaders working in tandem, (2) information exchange, (3) physical locale, (4) shared motivators, and (5) scaffolding to manage change. Conclusions. The OESSN model provides an explanation of the organizational factors that contributed to the adoption and incorporation of simulation into nursing curricula. Nursing programs that use the OESSN model may experience a more rapid or broad uptake of simulation when organizational factors that impact adoption and incorporation are considered and planned for.

Organizational Culture Shapes the Adoption and Incorporation of Simulation into Nursing Curricula: A Grounded Theory Study

PubMed Central

Jack, Susan M.; Eva, Kevin; Martin, Lynn

2014-01-01

Purpose. To create a substantive mid-range theory explaining how the organizational cultures of undergraduate nursing programs shape the adoption and incorporation of mid-to high-level technical fidelity simulators as a teaching strategy within curricula. Method. A constructivist grounded theory was used to guide this study which was conducted in Ontario, Canada, during 2011-12. Semistructured interviews (n = 43) with participants that included nursing administrators, nursing faculty, and simulation leaders across multiple programs (n = 13) informed this study. Additionally, key documents (n = 67) were reviewed. Purposeful and theoretical sampling was used and data were collected and analyzed simultaneously. Data were compared among and between sites. Findings. The organizational elements that shape simulation in nursing (OESSN) model depicts five key organizational factors at the nursing program level that shaped the adoption and incorporation of simulation: (1) leaders working in tandem, (2) information exchange, (3) physical locale, (4) shared motivators, and (5) scaffolding to manage change. Conclusions. The OESSN model provides an explanation of the organizational factors that contributed to the adoption and incorporation of simulation into nursing curricula. Nursing programs that use the OESSN model may experience a more rapid or broad uptake of simulation when organizational factors that impact adoption and incorporation are considered and planned for. PMID:24818018

An object oriented Python interface for atomistic simulations

NASA Astrophysics Data System (ADS)

Hynninen, T.; Himanen, L.; Parkkinen, V.; Musso, T.; Corander, J.; Foster, A. S.

2016-01-01

Programmable simulation environments allow one to monitor and control calculations efficiently and automatically before, during, and after runtime. Environments directly accessible in a programming environment can be interfaced with powerful external analysis tools and extensions to enhance the functionality of the core program, and by incorporating a flexible object based structure, the environments make building and analysing computational setups intuitive. In this work, we present a classical atomistic force field with an interface written in Python language. The program is an extension for an existing object based atomistic simulation environment.

A better sequence-read simulator program for metagenomics.

PubMed

Johnson, Stephen; Trost, Brett; Long, Jeffrey R; Pittet, Vanessa; Kusalik, Anthony

2014-01-01

There are many programs available for generating simulated whole-genome shotgun sequence reads. The data generated by many of these programs follow predefined models, which limits their use to the authors' original intentions. For example, many models assume that read lengths follow a uniform or normal distribution. Other programs generate models from actual sequencing data, but are limited to reads from single-genome studies. To our knowledge, there are no programs that allow a user to generate simulated data following non-parametric read-length distributions and quality profiles based on empirically-derived information from metagenomics sequencing data. We present BEAR (Better Emulation for Artificial Reads), a program that uses a machine-learning approach to generate reads with lengths and quality values that closely match empirically-derived distributions. BEAR can emulate reads from various sequencing platforms, including Illumina, 454, and Ion Torrent. BEAR requires minimal user input, as it automatically determines appropriate parameter settings from user-supplied data. BEAR also uses a unique method for deriving run-specific error rates, and extracts useful statistics from the metagenomic data itself, such as quality-error models. Many existing simulators are specific to a particular sequencing technology; however, BEAR is not restricted in this way. Because of its flexibility, BEAR is particularly useful for emulating the behaviour of technologies like Ion Torrent, for which no dedicated sequencing simulators are currently available. BEAR is also the first metagenomic sequencing simulator program that automates the process of generating abundances, which can be an arduous task. BEAR is useful for evaluating data processing tools in genomics. It has many advantages over existing comparable software, such as generating more realistic reads and being independent of sequencing technology, and has features particularly useful for metagenomics work.

Manned systems utilization analysis (study 2.1). Volume 5: Program listing for the LOVES computer code

NASA Technical Reports Server (NTRS)

Wray, S. T., Jr.

1975-01-01

The LOVES computer code developed to investigate the concept of space servicing operational satellites as an alternative to replacing expendable satellites or returning satellites to earth for ground refurbishment is presented. In addition to having the capability to simulate the expendable satellite operation and the ground refurbished satellite operation, the program is designed to simulate the logistics of space servicing satellites using an upper stage vehicle and/or the earth to orbit shuttle. The program not only provides for the initial deployment of the satellite but also simulates the random failure and subsequent replacement of various equipment modules comprising the satellite. The program has been used primarily to conduct trade studies and/or parametric studies of various space program operational philosophies.

The Interior Design Simulator. Courseware Evaluation for Vocational and Technical Education.

ERIC Educational Resources Information Center

Worts, Nancy; And Others

This courseware evaluation rates the Interior Design Simulator program developed by Orange Juice Software Systems. (This program--not contained in this document--allows the user to design a room of any shape with maximum dimensions of 14 x 26 feet.) Part A describes the program in terms of subject area (furniture arrangement) and hardware…

Program Costing with the CAMPUS Simulation Model. Project PRIME Report, Number 5.

ERIC Educational Resources Information Center

Cordes, David C.

The first section of this report on program costing with the CAMPUS simulation discusses the structuring process of Program Planning and Budgeting (PPB) systems, and emphasizes the ideas, rules, and principles for structuring resource data that have evolved during the 10 years of PPB existence. It also discusses the WICHE-PMS program…

Evaluating "Baby Think It Over" Infant Simulators: A Comparison Group Study

ERIC Educational Resources Information Center

Barnett, Jerrold E.

2006-01-01

To test the efficacy of Baby-Think-It-Over (BTIO) infant simulators, two versions of a sexuality education program were compared. While the program was designed to include BTIO as an important teaching technique, two schools (49 students) opted not to use them. These students completed all elements of the program except the BTIO activities. Their…

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mizell, D.; Carter, S.

In 1987, ISI's parallel distributed computing research group implemented a prototype sequential simulation system, designed for high-level simulation of candidate (Strategic Defense Initiative) architectures. A main design goal was to produce a simulation system that could incorporate non-trivial, executable representations of battle-management computations on each platform that were capable of controlling the actions of that platform throughout the simulation. The term BMA (battle manager abstraction) was used to refer to these simulated battle-management computations. In the authors first version of the simulator, the BMAs were C++ programs that we wrote and manually inserted into the system. Since then, they havemore » designed and implemented KMAC, a high-level language for writing BMA's. The KMAC preprocessor, built using the Unix tools lex 2 and YACC 3, translates KMAC source programs into C++ programs and passes them on to the C++ compiler. The KMAC preprocessor was incorporated into and operates under the control of the simulator's interactive user interface. After the KMAC preprocessor has translated a program into C++, the user interface system invokes the C++ compiler, and incorporates the resulting object code into the simulator load module for execution as part of a simulation run. This report describes the KMAC language and its preprocessor. Section 2 provides background material on the design of the simulation system that is necessary for understanding some of the parts of KMAC and some of the reasons it is structured the way it is. Section 3 describes the syntax and semantics of the language, and Section 4 discusses design of the preprocessor.« less

Partial Validation of Multibody Program to Optimize Simulated Trajectories II (POST II) Parachute Simulation With Interacting Forces

NASA Technical Reports Server (NTRS)

Raiszadeh, Ben; Queen, Eric M.

2002-01-01

A capability to simulate trajectories Of Multiple interacting rigid bodies has been developed. This capability uses the Program to Optimize Simulated Trajectories II (POST II). Previously, POST II had the ability to simulate multiple bodies without interacting forces. The current implementation is used for the Simulation of parachute trajectories, in which the parachute and suspended bodies can be treated as rigid bodies. An arbitrary set of connecting lines can be included in the model and are treated as massless spring-dampers. This paper discusses details of the connection line modeling and results of several test cases used to validate the capability.

A Mathematical Model for Vertical Attitude Takeoff and Landing (VATOL) Aircraft Simulation. Volume 1; Model Description Application

NASA Technical Reports Server (NTRS)

Fortenbaugh, R. L.

1980-01-01

A mathematical model of a high performance airplane capable of vertical attitude takeoff and landing (VATOL) was developed. An off line digital simulation program incorporating this model was developed to provide trim conditions and dynamic check runs for the piloted simulation studies and support dynamic analyses of proposed VATOL configuration and flight control concepts. Development details for the various simulation component models and the application of the off line simulation program, Vertical Attitude Take-Off and Landing Simulation (VATLAS), to develop a baseline control system for the Vought SF-121 VATOL airplane concept are described.

FD_BH: a program for simulating electromagnetic waves from a borehole antenna

USGS Publications Warehouse

Ellefsen, Karl J.

2002-01-01

Program FD_BH is used to simulate the electromagnetic waves generated by an antenna in a borehole. The model representing the antenna may include metallic parts, a coaxial cable as a feed to the driving point, and resistive loading. The program is written in the C programming language, and the program has been tested on both the Windows and the UNIX operating systems. This Open-File Report describes • The contents and organization of the Zip file (section 2). • The program files, the installation of the program, the input files, and the execution of the program (section 3). • Address to which suggestions for improving the program may be sent (section 4).

Huntington II Simulation Program - TAG. Student Workbook, Teacher's Guide, and Resource Handbook.

ERIC Educational Resources Information Center

Friedland, James

Presented are instructions for the use of "TAG," a model for estimating animal population in a given area. The computer program asks the student to estimate the number of bass in a simulated farm pond using the technique of tagging and recovery. The objective of the simulation is to teach principles for estimating animal populations when they…

To Determine the Effectiveness of Board Game Simulations in the Grade Five Social Studies Program. Final Report 80-7.

ERIC Educational Resources Information Center

Green, Vicki A.

The report describes a study designed to ascertain the effectiveness of 12 board game simulations developed and used in a fifth grade Canadian history program. Questions examined include: 1) Does the use of board game simulations increase group participation and cultural, environmental, and historical awareness? 2) Does use of the games promote…

Managing simulation-based training: A framework for optimizing learning, cost, and time

NASA Astrophysics Data System (ADS)

Richmond, Noah Joseph

This study provides a management framework for optimizing training programs for learning, cost, and time when using simulation based training (SBT) and reality based training (RBT) as resources. Simulation is shown to be an effective means for implementing activity substitution as a way to reduce risk. The risk profile of 22 US Air Force vehicles are calculated, and the potential risk reduction is calculated under the assumption of perfect substitutability of RBT and SBT. Methods are subsequently developed to relax the assumption of perfect substitutability. The transfer effectiveness ratio (TER) concept is defined and modeled as a function of the quality of the simulator used, and the requirements of the activity trained. The Navy F/A-18 is then analyzed in a case study illustrating how learning can be maximized subject to constraints in cost and time, and also subject to the decision maker's preferences for the proportional and absolute use of simulation. Solution methods for optimizing multiple activities across shared resources are next provided. Finally, a simulation strategy including an operations planning program (OPP), an implementation program (IP), an acquisition program (AP), and a pedagogical research program (PRP) is detailed. The study provides the theoretical tools to understand how to leverage SBT, a case study demonstrating these tools' efficacy, and a set of policy recommendations to enable the US military to better utilize SBT in the future.

Progress in modeling and simulation.

PubMed

Kindler, E

1998-01-01

For the modeling of systems, the computers are more and more used while the other "media" (including the human intellect) carrying the models are abandoned. For the modeling of knowledges, i.e. of more or less general concepts (possibly used to model systems composed of instances of such concepts), the object-oriented programming is nowadays widely used. For the modeling of processes existing and developing in the time, computer simulation is used, the results of which are often presented by means of animation (graphical pictures moving and changing in time). Unfortunately, the object-oriented programming tools are commonly not designed to be of a great use for simulation while the programming tools for simulation do not enable their users to apply the advantages of the object-oriented programming. Nevertheless, there are exclusions enabling to use general concepts represented at a computer, for constructing simulation models and for their easy modification. They are described in the present paper, together with true definitions of modeling, simulation and object-oriented programming (including cases that do not satisfy the definitions but are dangerous to introduce misunderstanding), an outline of their applications and of their further development. In relation to the fact that computing systems are being introduced to be control components into a large spectrum of (technological, social and biological) systems, the attention is oriented to models of systems containing modeling components.

Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report. [ODSP-3 code; OTEC Steady-State Analysis Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-12-04

The following appendices are included; Dynamic Simulation Program (ODSP-3); sample results of dynamic simulation; trip report - NH/sub 3/ safety precautions/accident records; trip report - US Coast Guard Headquarters; OTEC power system development, preliminary design test program report; medium turbine generator inspection point program; net energy analysis; bus bar cost of electricity; OTEC technical specifications; and engineer drawings. (WHK)

An adaptive maneuvering logic computer program for the simulation of one-on-one air-to-air combat. Volume 1: General description

NASA Technical Reports Server (NTRS)

Burgin, G. H.; Fogel, L. J.; Phelps, J. P.

1975-01-01

A technique for computer simulation of air combat is described. Volume 1 decribes the computer program and its development in general terms. Two versions of the program exist. Both incorporate a logic for selecting and executing air combat maneuvers with performance models of specific fighter aircraft. In the batch processing version the flight paths of two aircraft engaged in interactive aerial combat and controlled by the same logic are computed. The realtime version permits human pilots to fly air-to-air combat against the adaptive maneuvering logic (AML) in Langley Differential Maneuvering Simulator (DMS). Volume 2 consists of a detailed description of the computer programs.

General purpose simulation system of the data management system for Space Shuttle mission 18

NASA Technical Reports Server (NTRS)

Bengtson, N. M.; Mellichamp, J. M.; Smith, O. C.

1976-01-01

A simulation program for the flow of data through the Data Management System of Spacelab and Space Shuttle was presented. The science, engineering, command and guidance, navigation and control data were included. The programming language used was General Purpose Simulation System V (OS). The science and engineering data flow was modeled from its origin at the experiments and subsystems to transmission from Space Shuttle. Command data flow was modeled from the point of reception onboard and from the CDMS Control Panel to the experiments and subsystems. The GN&C data flow model handled data between the General Purpose Computer and the experiments and subsystems. Mission 18 was the particular flight chosen for simulation. The general structure of the program is presented, followed by a user's manual. Input data required to make runs are discussed followed by identification of the output statistics. The appendices contain a detailed model configuration, program listing and results.

User's guide to SEAWAT; a computer program for simulation of three-dimensional variable-density ground-water flow

USGS Publications Warehouse

Guo, Weixing; Langevin, C.D.

2002-01-01

This report documents a computer program (SEAWAT) that simulates variable-density, transient, ground-water flow in three dimensions. The source code for SEAWAT was developed by combining MODFLOW and MT3DMS into a single program that solves the coupled flow and solute-transport equations. The SEAWAT code follows a modular structure, and thus, new capabilities can be added with only minor modifications to the main program. SEAWAT reads and writes standard MODFLOW and MT3DMS data sets, although some extra input may be required for some SEAWAT simulations. This means that many of the existing pre- and post-processors can be used to create input data sets and analyze simulation results. Users familiar with MODFLOW and MT3DMS should have little difficulty applying SEAWAT to problems of variable-density ground-water flow.

A Management Information System Model for Program Management. Ph.D. Thesis - Oklahoma State Univ.; [Computerized Systems Analysis

NASA Technical Reports Server (NTRS)

Shipman, D. L.

1972-01-01

The development of a model to simulate the information system of a program management type of organization is reported. The model statistically determines the following parameters: type of messages, destinations, delivery durations, type processing, processing durations, communication channels, outgoing messages, and priorites. The total management information system of the program management organization is considered, including formal and informal information flows and both facilities and equipment. The model is written in General Purpose System Simulation 2 computer programming language for use on the Univac 1108, Executive 8 computer. The model is simulated on a daily basis and collects queue and resource utilization statistics for each decision point. The statistics are then used by management to evaluate proposed resource allocations, to evaluate proposed changes to the system, and to identify potential problem areas. The model employs both empirical and theoretical distributions which are adjusted to simulate the information flow being studied.

Desktop Modeling and Simulation: Parsimonious, yet Effective Discrete-Event Simulation Analysis

NASA Technical Reports Server (NTRS)

Bradley, James R.

2012-01-01

This paper evaluates how quickly students can be trained to construct useful discrete-event simulation models using Excel The typical supply chain used by many large national retailers is described, and an Excel-based simulation model is constructed of it The set of programming and simulation skills required for development of that model are then determined we conclude that six hours of training are required to teach the skills to MBA students . The simulation presented here contains all fundamental functionallty of a simulation model, and so our result holds for any discrete-event simulation model. We argue therefore that Industry workers with the same technical skill set as students having completed one year in an MBA program can be quickly trained to construct simulation models. This result gives credence to the efficacy of Desktop Modeling and Simulation whereby simulation analyses can be quickly developed, run, and analyzed with widely available software, namely Excel.

General specifications for the development of a PC-based simulator of the NASA RECON system

NASA Technical Reports Server (NTRS)

Dominick, Wayne D. (Editor); Triantafyllopoulos, Spiros

1984-01-01

The general specifications for the design and implementation of an IBM PC/XT-based simulator of the NASA RECON system, including record designs, file structure designs, command language analysis, program design issues, error recovery considerations, and usage monitoring facilities are discussed. Once implemented, such a simulator will be utilized to evaluate the effectiveness of simulated information system access in addition to actual system usage as part of the total educational programs being developed within the NASA contract.

IMPETUS - Interactive MultiPhysics Environment for Unified Simulations.

PubMed

Ha, Vi Q; Lykotrafitis, George

2016-12-08

We introduce IMPETUS - Interactive MultiPhysics Environment for Unified Simulations, an object oriented, easy-to-use, high performance, C++ program for three-dimensional simulations of complex physical systems that can benefit a large variety of research areas, especially in cell mechanics. The program implements cross-communication between locally interacting particles and continuum models residing in the same physical space while a network facilitates long-range particle interactions. Message Passing Interface is used for inter-processor communication for all simulations. Copyright © 2016 Elsevier Ltd. All rights reserved.

Combining high performance simulation, data acquisition, and graphics display computers

NASA Technical Reports Server (NTRS)

Hickman, Robert J.

1989-01-01

Issues involved in the continuing development of an advanced simulation complex are discussed. This approach provides the capability to perform the majority of tests on advanced systems, non-destructively. The controlled test environments can be replicated to examine the response of the systems under test to alternative treatments of the system control design, or test the function and qualification of specific hardware. Field tests verify that the elements simulated in the laboratories are sufficient. The digital computer is hosted by a Digital Equipment Corp. MicroVAX computer with an Aptec Computer Systems Model 24 I/O computer performing the communication function. An Applied Dynamics International AD100 performs the high speed simulation computing and an Evans and Sutherland PS350 performs on-line graphics display. A Scientific Computer Systems SCS40 acts as a high performance FORTRAN program processor to support the complex, by generating numerous large files from programs coded in FORTRAN that are required for the real time processing. Four programming languages are involved in the process, FORTRAN, ADSIM, ADRIO, and STAPLE. FORTRAN is employed on the MicroVAX host to initialize and terminate the simulation runs on the system. The generation of the data files on the SCS40 also is performed with FORTRAN programs. ADSIM and ADIRO are used to program the processing elements of the AD100 and its IOCP processor. STAPLE is used to program the Aptec DIP and DIA processors.

Using Simulation in a Psychiatric Mental Health Nurse Practitioner Doctoral Program.

PubMed

Calohan, Jess; Pauli, Eric; Combs, Teresa; Creel, Andrea; Convoy, Sean; Owen, Regina

The use and effectiveness of simulation with standardized patients in undergraduate and graduate nursing education programs is well documented. Simulation has been primarily used to develop health assessment skills. Evidence supports using simulation and standardized patients in psychiatric-mental health nurse practitioner (PMHNP) programs is useful in developing psychosocial assessment skills. These interactions provide individualized and instantaneous clinical feedback to the student from faculty, peers, and standardized patients. Incorporating simulation into advanced practice psychiatric-mental health nursing curriculum allows students to develop the necessary requisite skills and principles needed to safely and effectively provide care to patients. There are no documented standardized processes for using simulation throughout a doctor of nursing practice PMHNP curriculum. The purpose of this article is to describe a framework for using simulation with standardized patients in a PMHNP curriculum. Students report high levels of satisfaction with the simulation experience and believe that they are more prepared for clinical rotations. Faculty feedback indicates that simulated clinical scenarios are a method to ensure that each student experiences demonstrate a minimum standard of competency ahead of clinical rotations with live patients. Initial preceptor feedback indicates that students are more prepared for clinical practice and function more independently than students that did not experience this standardized clinical simulation framework. Published by Elsevier Inc.

Creating a sustainable, interprofessional-team training program: initial results.

PubMed

Riggall, Virginia K; Smith, Charlene M

2015-01-01

The purpose of this program evaluation was to explore whether incorporating deliberate learning concepts, through the use of simulated patient scenarios to teach interprofessional collaboration skills to a healthcare team on one acute-care hospital unit, would improve the resuscitation response in the first 5 minutes on that unit. This was a pilot program evaluation utilizing a unit-based, clinical nurse specialist in the deployment of an interprofessional educational program involving simulation on an acute medical floor in a large tertiary-care hospital. Eighty-four staff members participated in 17 simulations. The sample included first-year internal-medicine residents, registered nurses, respiratory therapists, and patient care technicians. This was a program evaluation that used the TeamSTEPPS Teamwork Perceptions Questionnaire (T-TPQ) (Classroom slides: TeamSTEPPS essentials; http://www.ahrq.gov/professionals/education/curriculum-tools/teamstepps/instructor/essentials/slessentials.html#s3) during the presimulation/postsimulation sessions to assess the participants' perceptions of teamwork. Expected intervention behaviors were collected through observations of participants in the simulations and compared with the American Heart Association guidelines (Circulation 2010;122:S685-S670, S235-S337). Common perceptions of participants regarding the experience were obtained through open-ended evaluation questions. Fifty-three participants completed the pre- and post-T-TPQ. Mean scores in the leadership category of T-TPQ decreased significantly (P = .003) from the pretest (median, 2.167) to the T-TPQ posttest (median, 2.566). Only 35% of the groups administered a defibrillation during the ventricular fibrillation simulation scenario, and only 1 group delivered this shock within the American Heart Association's recommended time frame of 2 minutes (Circulation 2010;122:S235-S337). A single resuscitation simulation was not enough interventional dosage for staff to improve the resuscitation process. A longitudinal study should be conducted to determine the effectiveness of the program after staff members have repeated the program multiple times. A unit-based quality-improvement simulation training program could help improve the first-5-minute response and resuscitation skills of staff by increasing the frequency of unit-based training overseen by the unit's clinical nurse specialist.

Real-Time Multiprocessor Programming Language (RTMPL) user's manual

NASA Technical Reports Server (NTRS)

Arpasi, D. J.

1985-01-01

A real-time multiprocessor programming language (RTMPL) has been developed to provide for high-order programming of real-time simulations on systems of distributed computers. RTMPL is a structured, engineering-oriented language. The RTMPL utility supports a variety of multiprocessor configurations and types by generating assembly language programs according to user-specified targeting information. Many programming functions are assumed by the utility (e.g., data transfer and scaling) to reduce the programming chore. This manual describes RTMPL from a user's viewpoint. Source generation, applications, utility operation, and utility output are detailed. An example simulation is generated to illustrate many RTMPL features.

Integrated Modeling, Mapping, and Simulation (IMMS) framework for planning exercises.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Friedman-Hill, Ernest J.; Plantenga, Todd D.

2010-06-01

The Integrated Modeling, Mapping, and Simulation (IMMS) program is designing and prototyping a simulation and collaboration environment for linking together existing and future modeling and simulation tools to enable analysts, emergency planners, and incident managers to more effectively, economically, and rapidly prepare, analyze, train, and respond to real or potential incidents. When complete, the IMMS program will demonstrate an integrated modeling and simulation capability that supports emergency managers and responders with (1) conducting 'what-if' analyses and exercises to address preparedness, analysis, training, operations, and lessons learned, and (2) effectively, economically, and rapidly verifying response tactics, plans and procedures.

Three-dimensional interactive Molecular Dynamics program for the study of defect dynamics in crystals

NASA Astrophysics Data System (ADS)

Patriarca, M.; Kuronen, A.; Robles, M.; Kaski, K.

2007-01-01

The study of crystal defects and the complex processes underlying their formation and time evolution has motivated the development of the program ALINE for interactive molecular dynamics experiments. This program couples a molecular dynamics code to a Graphical User Interface and runs on a UNIX-X11 Window System platform with the MOTIF library, which is contained in many standard Linux releases. ALINE is written in C, thus giving the user the possibility to modify the source code, and, at the same time, provides an effective and user-friendly framework for numerical experiments, in which the main parameters can be interactively varied and the system visualized in various ways. We illustrate the main features of the program through some examples of detection and dynamical tracking of point-defects, linear defects, and planar defects, such as stacking faults in lattice-mismatched heterostructures. Program summaryTitle of program:ALINE Catalogue identifier:ADYJ_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADYJ_v1_0 Program obtainable from: CPC Program Library, Queen University of Belfast, N. Ireland Computer for which the program is designed and others on which it has been tested: Computers:DEC ALPHA 300, Intel i386 compatible computers, G4 Apple Computers Installations:Laboratory of Computational Engineering, Helsinki University of Technology, Helsinki, Finland Operating systems under which the program has been tested:True64 UNIX, Linux-i386, Mac OS X 10.3 and 10.4 Programming language used:Standard C and MOTIF libraries Memory required to execute with typical data:6 Mbytes but may be larger depending on the system size No. of lines in distributed program, including test data, etc.:16 901 No. of bytes in distributed program, including test data, etc.:449 559 Distribution format:tar.gz Nature of physical problem:Some phenomena involving defects take place inside three-dimensional crystals at times which can be hardly predicted. For this reason they are difficult to detect and track even within numerical experiments, especially when one is interested in studying their dynamical properties and time evolution. Furthermore, traditional simulation methods require the storage of a huge amount of data which in turn may imply a long work for their analysis. Method of solution:Simplifications of the simulation work described above strongly depend also on the computer performance. It has now become possible to realize some of such simplifications thanks to the real possibility of using interactive programs. The solution proposed here is based on the development of an interactive graphical simulation program both for avoiding large storage of data and the subsequent elaboration and analysis as well as for visualizing and tracking many phenomena inside three-dimensional samples. However, the full computational power of traditional simulation programs may not be available in general in programs with graphical user interfaces, due to their interactive nature. Nevertheless interactive programs can still be very useful for detecting processes difficult to visualize, restricting the range or making a fine tuning of the parameters, and tailoring the faster programs toward precise targets. Restrictions on the complexity of the problem:The restrictions on the applicability of the program are related to the computer resources available. The graphical interface and interactivity demand computational resources that depend on the particular numerical simulation to be performed. To preserve a balance between speed and resources, the choice of the number of atoms to be simulated is critical. With an average current computer, simulations of systems with more than 10 5 atoms may not be easily feasible on an interactive scheme. Another restriction is related to the fact that the program was originally designed to simulate systems in the solid phase, so that problems in the simulation may occur if some particular physical quantities are computed beyond the melting point. Typical running time:It depends on the machine architecture, system size, and user needs. Unusual features of the program:In the program, besides the window in which the system is represented in real space, an additional graphical window presenting the real time distribution histogram for different physical variables (such as kinetic or potential energy) is included. Such tool is very interesting for making demonstrative numerical experiments for teaching purposes as well as for research, e.g., for detecting and tracking crystal defects. The program includes: an initial condition builder, an interactive display of the simulation, a set of tools which allow the user to filter through different physical quantities the information—either displayed in real time or printed in the output files—and to perform an efficient search of the interesting regions of parameter space.

Effects of Simulated Land-Use Changes on Water Quality of Lake Maumelle, Arkansas

USGS Publications Warehouse

Hart, Rheannon M.; Westerman, Drew A.; Petersen, James C.; Green, W. Reed; De Lanois, Jeanne L.

2011-01-01

Lake Maumelle is one of two principal drinking-water supplies for the Little Rock and North Little Rock metropolitan areas. Lake Maumelle and the Maumelle River (its primary tributary) are more pristine than most other reservoirs and streams in the region. However, as the Lake Maumelle watershed becomes increasingly more urbanized and timber harvesting becomes more frequent, concerns about the sustainability of the quality of the water supply also have increased. Two models were developed to partially address these concerns. A Hydrological Simulation Program-FORTRAN model was developed using input data collected from October 2004 through 2008. A CE-QUAL-W2 model was developed to simulate reservoir hydrodynamics and selected water quality using the simulated output from the Hydrological Simulation Program-FORTRAN model from January 2005 through 2008. The Hydrological Simulation Program-FORTRAN watershed model was calibrated to five streamflow-gaging stations, and in general, these stations characterize a range of subwatershed areas with varying land-use types. Continuous streamflow data, discrete sediment concentration data, and other discrete water-quality data were used to calibrate the Lake Maumelle Hydrological Simulation Program-FORTRAN model. The CE-QUAL-W2 reservoir model was calibrated to water-quality data and reservoir pool altitude collected during January 2005 through December 2008 at three lake stations. In general, the overall simulation for the Hydrological Simulation Program-FORTRAN and CE-UAL-W2 models matched reasonably well to the measured data. In general, simulated and measured suspended-sediment concentrations during periods of base flow (streamflows not substantially influenced by runoff) agree reasonably well for Williams Junction (with differences-simulated minus measured value-generally ranging from -14 to 19 mg/L, and percent difference-relative to the measured value-ranging from -87 to 642 percent) and Wye (differences generally ranging from -2 to 14 mg/L, -62 to 251 percent); however, the Hydrological Simulation Program-FORTRAN model generally does not match the suspended-sediment concentrations for all stations during periods of stormflow (streamflow substantially influenced by runoff). Generally, this is also the case for fecal coliform bacteria numbers and total organic carbon and nutrient concentrations. In general, water temperature and dissolved-oxygen concentration simulations followed measured seasonal trends for all stations with the largest differences occurring during periods of lowest water temperatures (for temperature) or during the periods of lowest measured dissolved-oxygen concentrations (for dissolved oxygen). For the CE-QUAL-W2 model, simulated vertical distributions of temperatures and dissolved-oxygen concentrations agreed with measured distributions even for complex temperature profiles. Considering the oligotrophic-mesotrophic (low to intermediate primary productivity and associated low nutrient concentrations) condition of Lake Maumelle, simulated algae, phosphorus, and ammonia concentrations compared well with generally low measured values.

Developments in the electron gun simulation program, EGUN

NASA Astrophysics Data System (ADS)

Herrmannsfeldt, W. B.

1994-11-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described.

Developments in the electron gun simulation program, EGUN

NASA Astrophysics Data System (ADS)

Herrmannsfeldt, W. B.

1995-07-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described.

Evolution of the Standard Simulation Architecture

DTIC Science & Technology

2004-06-01

Interoperability Workshop, Paper 02S-SIW-016. 5. Deitel & Deitel , 2001. “C++ How to Program , Third Edition.” Prentice Hall, Inc., Upper Saddle...carefully followed for software to be successfully reused in other programs . The Standard Simulation Architecture (SSA) promotes these principles...capabilities described in this paper have been developed and successfully used on various government programs . This paper attempts to bring these

Automatic programming of simulation models

NASA Technical Reports Server (NTRS)

Schroer, Bernard J.; Tseng, Fan T.; Zhang, Shou X.; Dwan, Wen S.

1990-01-01

The concepts of software engineering were used to improve the simulation modeling environment. Emphasis was placed on the application of an element of rapid prototyping, or automatic programming, to assist the modeler define the problem specification. Then, once the problem specification has been defined, an automatic code generator is used to write the simulation code. The following two domains were selected for evaluating the concepts of software engineering for discrete event simulation: manufacturing domain and a spacecraft countdown network sequence. The specific tasks were to: (1) define the software requirements for a graphical user interface to the Automatic Manufacturing Programming System (AMPS) system; (2) develop a graphical user interface for AMPS; and (3) compare the AMPS graphical interface with the AMPS interactive user interface.

Building Interactive Simulations in Web Pages without Programming.

PubMed

Mailen Kootsey, J; McAuley, Grant; Bernal, Julie

2005-01-01

A software system is described for building interactive simulations and other numerical calculations in Web pages. The system is based on a new Java-based software architecture named NumberLinX (NLX) that isolates each function required to build the simulation so that a library of reusable objects could be assembled. The NLX objects are integrated into a commercial Web design program for coding-free page construction. The model description is entered through a wizard-like utility program that also functions as a model editor. The complete system permits very rapid construction of interactive simulations without coding. A wide range of applications are possible with the system beyond interactive calculations, including remote data collection and processing and collaboration over a network.

Gstat: a program for geostatistical modelling, prediction and simulation

NASA Astrophysics Data System (ADS)

Pebesma, Edzer J.; Wesseling, Cees G.

1998-01-01

Gstat is a computer program for variogram modelling, and geostatistical prediction and simulation. It provides a generic implementation of the multivariable linear model with trends modelled as a linear function of coordinate polynomials or of user-defined base functions, and independent or dependent, geostatistically modelled, residuals. Simulation in gstat comprises conditional or unconditional (multi-) Gaussian sequential simulation of point values or block averages, or (multi-) indicator sequential simulation. Besides many of the popular options found in other geostatistical software packages, gstat offers the unique combination of (i) an interactive user interface for modelling variograms and generalized covariances (residual variograms), that uses the device-independent plotting program gnuplot for graphical display, (ii) support for several ascii and binary data and map file formats for input and output, (iii) a concise, intuitive and flexible command language, (iv) user customization of program defaults, (v) no built-in limits, and (vi) free, portable ANSI-C source code. This paper describes the class of problems gstat can solve, and addresses aspects of efficiency and implementation, managing geostatistical projects, and relevant technical details.

What we call what we do affects how we do it: a new nomenclature for simulation research in medical education.

PubMed

Haji, Faizal A; Hoppe, Daniel J; Morin, Marie-Paule; Giannoulakis, Konstantine; Koh, Jansen; Rojas, David; Cheung, Jeffrey J H

2014-05-01

Rapid technological advances and concern for patient safety have increased the focus on simulation as a pedagogical tool for educating health care providers. To date, simulation research scholarship has focused on two areas; evaluating instructional designs of simulation programs, and the integration of simulation into a broader educational context. However, these two categories of research currently exist under a single label-Simulation-Based Medical Education. In this paper we argue that introducing a more refined nomenclature within which to frame simulation research is necessary for researchers, to appropriately design research studies and describe their findings, and for end-point users (such as program directors and educators), to more appropriately understand and utilize this evidence.

Remote manipulator system flexibility analysis program: Mission planning, mission analysis, and software formulation

NASA Technical Reports Server (NTRS)

Kumar, L.

1978-01-01

A computer program is described for calculating the flexibility coefficients as arm design changes are made for the remote manipulator system. The coefficients obtained are required as input for a second program which reduces the number of payload deployment and retrieval system simulation runs required to simulate the various remote manipulator system maneuvers. The second program calculates end effector flexibility and joint flexibility terms for the torque model of each joint for any arbitrary configurations. The listing of both programs is included in the appendix.

A modular radiative transfer program for gas filter correlation radiometry

NASA Technical Reports Server (NTRS)

Casas, J. C.; Campbell, S. A.

1977-01-01

The fundamentals of a computer program, simulated monochromatic atmospheric radiative transfer (SMART), which calculates atmospheric path transmission, solar radiation, and thermal radiation in the 4.6 micrometer spectral region, are described. A brief outline of atmospheric absorption properties and line by line transmission calculations is explained in conjunction with an outline of the SMART computational procedures. Program flexibility is demonstrated by simulating the response of a gas filter correlation radiometer as one example of an atmospheric infrared sensor. Program limitations, input data requirements, program listing, and comparison of SMART transmission calculations are presented.

Computer simulation of space station computer steered high gain antenna

NASA Technical Reports Server (NTRS)

Beach, S. W.

1973-01-01

The mathematical modeling and programming of a complete simulation program for a space station computer-steered high gain antenna are described. The program provides for reading input data cards, numerically integrating up to 50 first order differential equations, and monitoring up to 48 variables on printed output and on plots. The program system consists of a high gain antenna, an antenna gimbal control system, an on board computer, and the environment in which all are to operate.

A user's guide to the Flexible Spacecraft Dynamics and Control Program

NASA Technical Reports Server (NTRS)

Fedor, J. V.

1984-01-01

A guide to the use of the Flexible Spacecraft Dynamics Program (FSD) is presented covering input requirements, control words, orbit generation, spacecraft description and simulation options, and output definition. The program can be used in dynamics and control analysis as well as in orbit support of deployment and control of spacecraft. The program is applicable to inertially oriented spinning, Earth oriented or gravity gradient stabilized spacecraft. Internal and external environmental effects can be simulated.

Development of a computer program data base of a navigation aid environment for simulated IFR flight and landing studies

NASA Technical Reports Server (NTRS)

Bergeron, H. P.; Haynie, A. T.; Mcdede, J. B.

1980-01-01

A general aviation single pilot instrument flight rule simulation capability was developed. Problems experienced by single pilots flying in IFR conditions were investigated. The simulation required a three dimensional spatial navaid environment of a flight navigational area. A computer simulation of all the navigational aids plus 12 selected airports located in the Washington/Norfolk area was developed. All programmed locations in the list were referenced to a Cartesian coordinate system with the origin located at a specified airport's reference point. All navigational aids with their associated frequencies, call letters, locations, and orientations plus runways and true headings are included in the data base. The simulation included a TV displayed out-the-window visual scene of country and suburban terrain and a scaled model runway complex. Any of the programmed runways, with all its associated navaids, can be referenced to a runway on the airport in this visual scene. This allows a simulation of a full mission scenario including breakout and landing.

Simulation of mass storage systems operating in a large data processing facility

NASA Technical Reports Server (NTRS)

Holmes, R.

1972-01-01

A mass storage simulation program was written to aid system designers in the design of a data processing facility. It acts as a tool for measuring the overall effect on the facility of on-line mass storage systems, and it provides the means of measuring and comparing the performance of competing mass storage systems. The performance of the simulation program is demonstrated.

Simulating a base population in honey bee for molecular genetic studies

PubMed Central

2012-01-01

Background Over the past years, reports have indicated that honey bee populations are declining and that infestation by an ecto-parasitic mite (Varroa destructor) is one of the main causes. Selective breeding of resistant bees can help to prevent losses due to the parasite, but it requires that a robust breeding program and genetic evaluation are implemented. Genomic selection has emerged as an important tool in animal breeding programs and simulation studies have shown that it yields more accurate breeding value estimates, higher genetic gain and low rates of inbreeding. Since genomic selection relies on marker data, simulations conducted on a genomic dataset are a pre-requisite before selection can be implemented. Although genomic datasets have been simulated in other species undergoing genetic evaluation, simulation of a genomic dataset specific to the honey bee is required since this species has a distinct genetic and reproductive biology. Our software program was aimed at constructing a base population by simulating a random mating honey bee population. A forward-time population simulation approach was applied since it allows modeling of genetic characteristics and reproductive behavior specific to the honey bee. Results Our software program yielded a genomic dataset for a base population in linkage disequilibrium. In addition, information was obtained on (1) the position of markers on each chromosome, (2) allele frequency, (3) χ2 statistics for Hardy-Weinberg equilibrium, (4) a sorted list of markers with a minor allele frequency less than or equal to the input value, (5) average r2 values of linkage disequilibrium between all simulated marker loci pair for all generations and (6) average r2 value of linkage disequilibrium in the last generation for selected markers with the highest minor allele frequency. Conclusion We developed a software program that takes into account the genetic and reproductive biology specific to the honey bee and that can be used to constitute a genomic dataset compatible with the simulation studies necessary to optimize breeding programs. The source code together with an instruction file is freely accessible at http://msproteomics.org/Research/Misc/honeybeepopulationsimulator.html PMID:22520469

Simulating a base population in honey bee for molecular genetic studies.

PubMed

Gupta, Pooja; Conrad, Tim; Spötter, Andreas; Reinsch, Norbert; Bienefeld, Kaspar

2012-06-27

Over the past years, reports have indicated that honey bee populations are declining and that infestation by an ecto-parasitic mite (Varroa destructor) is one of the main causes. Selective breeding of resistant bees can help to prevent losses due to the parasite, but it requires that a robust breeding program and genetic evaluation are implemented. Genomic selection has emerged as an important tool in animal breeding programs and simulation studies have shown that it yields more accurate breeding value estimates, higher genetic gain and low rates of inbreeding. Since genomic selection relies on marker data, simulations conducted on a genomic dataset are a pre-requisite before selection can be implemented. Although genomic datasets have been simulated in other species undergoing genetic evaluation, simulation of a genomic dataset specific to the honey bee is required since this species has a distinct genetic and reproductive biology. Our software program was aimed at constructing a base population by simulating a random mating honey bee population. A forward-time population simulation approach was applied since it allows modeling of genetic characteristics and reproductive behavior specific to the honey bee. Our software program yielded a genomic dataset for a base population in linkage disequilibrium. In addition, information was obtained on (1) the position of markers on each chromosome, (2) allele frequency, (3) χ(2) statistics for Hardy-Weinberg equilibrium, (4) a sorted list of markers with a minor allele frequency less than or equal to the input value, (5) average r(2) values of linkage disequilibrium between all simulated marker loci pair for all generations and (6) average r2 value of linkage disequilibrium in the last generation for selected markers with the highest minor allele frequency. We developed a software program that takes into account the genetic and reproductive biology specific to the honey bee and that can be used to constitute a genomic dataset compatible with the simulation studies necessary to optimize breeding programs. The source code together with an instruction file is freely accessible at http://msproteomics.org/Research/Misc/honeybeepopulationsimulator.html.

Simulation and animation of sensor-driven robots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, C.; Trivedi, M.M.; Bidlack, C.R.

1994-10-01

Most simulation and animation systems utilized in robotics are concerned with simulation of the robot and its environment without simulation of sensors. These systems have difficulty in handling robots that utilize sensory feedback in their operation. In this paper, a new design of an environment for simulation, animation, and visualization of sensor-driven robots is presented. As sensor technology advances, increasing numbers of robots are equipped with various types of sophisticated sensors. The main goal of creating the visualization environment is to aide the automatic robot programming and off-line programming capabilities of sensor-driven robots. The software system will help the usersmore » visualize the motion and reaction of the sensor-driven robot under their control program. Therefore, the efficiency of the software development is increased, the reliability of the software and the operation safety of the robot are ensured, and the cost of new software development is reduced. Conventional computer-graphics-based robot simulation and animation software packages lack of capabilities for robot sensing simulation. This paper describes a system designed to overcome this deficiency.« less

Simulation model for wind energy storage systems. Volume II. Operation manual. [SIMWEST code

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume II, the SIMWEST operation manual, describes the usage of the SIMWEST program, the designmore » of the library components, and a number of simple example simulations intended to familiarize the user with the program's operation. Volume II also contains a listing of each SIMWEST library subroutine.« less

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Appendix A: ROBSIM user's guide

NASA Technical Reports Server (NTRS)

Haley, D. C.; Almand, B. J.; Thomas, M. M.; Krauze, L. D.; Gremban, K. D.; Sanborn, J. C.; Kelley, J. H.; Depkovich, T. M.; Wolfe, W. J.; Nguyen, T.

1986-01-01

The purpose of the Robotics Simulation Program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotics systems. ROBSIM is program in FORTRAN 77 for use on a VAX 11/750 computer under the VMS operating system. This user's guide describes the capabilities of the ROBSIM programs, including the system definition function, the analysis tools function and the postprocessor function. The options a user may encounter with each of these executables are explained in detail and the different program prompts appearing to the user are included. Some useful suggestions concerning the appropriate answers to be given by the user are provided. An example user interactive run in enclosed for each of the main program services, and some of the capabilities are illustrated.

A modular finite-element model (MODFE) for areal and axisymmetric ground-water-flow problems, Part 3: Design philosophy and programming details

USGS Publications Warehouse

Torak, L.J.

1993-01-01

A MODular Finite-Element, digital-computer program (MODFE) was developed to simulate steady or unsteady-state, two-dimensional or axisymmetric ground-water-flow. The modular structure of MODFE places the computationally independent tasks that are performed routinely by digital-computer programs simulating ground-water flow into separate subroutines, which are executed from the main program by control statements. Each subroutine consists of complete sets of computations, or modules, which are identified by comment statements, and can be modified by the user without affecting unrelated computations elsewhere in the program. Simulation capabilities can be added or modified by either adding or modifying subroutines that perform specific computational tasks, and the modular-program structure allows the user to create versions of MODFE that contain only the simulation capabilities that pertain to the ground-water problem of interest. MODFE is written in a Fortran programming language that makes it virtually device independent and compatible with desk-top personal computers and large mainframes. MODFE uses computer storage and execution time efficiently by taking advantage of symmetry and sparseness within the coefficient matrices of the finite-element equations. Parts of the matrix coefficients are computed and stored as single-subscripted variables, which are assembled into a complete coefficient just prior to solution. Computer storage is reused during simulation to decrease storage requirements. Descriptions of subroutines that execute the computational steps of the modular-program structure are given in tables that cross reference the subroutines with particular versions of MODFE. Programming details of linear and nonlinear hydrologic terms are provided. Structure diagrams for the main programs show the order in which subroutines are executed for each version and illustrate some of the linear and nonlinear versions of MODFE that are possible. Computational aspects of changing stresses and boundary conditions with time and of mass-balance and error terms are given for each hydrologic feature. Program variables are listed and defined according to their occurrence in the main programs and in subroutines. Listings of the main programs and subroutines are given.

A simulation model to estimate cost-offsets for a disease-management program for chronic kidney disease.

PubMed

Gandjour, Afschin; Tschulena, Ulrich; Steppan, Sonja; Gatti, Emanuele

2015-04-01

The aim of this paper is to develop a simulation model that analyzes cost-offsets of a hypothetical disease management program (DMP) for patients with chronic kidney disease (CKD) in Germany compared to no such program. A lifetime Markov model with simulated 65-year-old patients with CKD was developed using published data on costs and health status and simulating the progression to end-stage renal disease (ESRD), cardiovascular disease and death. A statutory health insurance perspective was adopted. This modeling study shows considerable potential for cost-offsets from a DMP for patients with CKD. The potential for cost-offsets increases with relative risk reduction by the DMP and baseline glomerular filtration rate. Results are most sensitive to the cost of dialysis treatment. This paper presents a general 'prototype' simulation model for the prevention of ESRD. The model allows for further modification and adaptation in future applications.

THERM 5 / WINDOW 5 NFRC simulation manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Robin; Kohler, Christian; Arasteh, Dariush

This document, the ''THERM 5/WINDOW 5 NFRC Simulation Manual', discusses how to use the THERM and WINDOW programs to model products for NFRC certified simulations and assumes that the user is already familiar with those programs. In order to learn how to use these programs, it is necessary to become familiar with the material in both the ''THERM User's Manual'' and the ''WINDOW User's Manual''. In general, this manual references the User's Manuals rather than repeating the information. If there is a conflict between either of the User Manual and this ''THERM 5/''WINDOW 5 NFRC Simulation Manual'', the ''THERM 5/WINDOWmore » 5 NFRC Simulation Manual'' takes precedence. In addition, if this manual is in conflict with any NFRC standards, the standards take precedence. For example, if samples in this manual do not follow the current taping and testing NFRC standards, the standards not the samples in this manual, take precedence.« less

Virtual engine management simulator for educational purposes

NASA Astrophysics Data System (ADS)

Drosescu, R.

2017-10-01

This simulator was conceived as a software program capable of generating complex control signals, identical to those in the electronic management systems of modern spark ignition or diesel engines. Speed in rpm and engine load percentage defined by throttle opening angle represent the input variables in the simulation program and are graphically entered by two-meter instruments from the simulator central block diagram. The output signals are divided into four categories: synchronization and position of each cylinder, spark pulses for spark ignition engines, injection pulses and, signals for generating the knock window for each cylinder in the case of a spark ignition engine. The simulation program runs in real-time so each signal evolution reflects the real behavior on a physically thermal engine. In this way, the generated signals (ignition or injection pulses) can be used with additionally drivers to control an engine on the test bench.

An electric scooter simulation program for training the driving skills of stroke patients with mobility problems: a pilot study.

PubMed

Jannink, Michiel J A; Erren-Wolters, C Victorien; de Kort, Alexander C; van der Kooij, Herman

2008-12-01

This paper describes an electric scooter simulation program and a first evaluation study in which we explored if it is possible to train the driving skills of future users of electric mobility scooters by means of an electric scooter simulation program in addition to conventional electric scooter training. Within this explorative study,10 stroke survivors were randomly assigned to either the control (n=5) or the electric scooter simulation intervention group (n=5). Participants were assessed twice on the functional evaluating rating scale. During the followup measurement, subjective experiences regarding both forms of electric scooter training were elicited by a questionnaire. After a training period of 5 weeks, both groups improved on the Functional Evaluation Rating Scale. It can be concluded that the patients with stroke were satisfied with the electric scooter simulation training.

Enhancing Trifocal Leadership Practices Using Simulation in a Pediatric Charge Nurse Orientation Program.

PubMed

Clark, Teresa J; Yoder-Wise, Patricia S

2015-07-01

A well-established charge nurse orientation program was enhanced with the addition of a simulation, addressing three primary populations (the trifocus) with whom charge nurses interact: patients, patients' parents, and other staff members. In this pilot quality improvement project, 20 staff nurses enrolled in the orientation program and were assigned a mentor. Only one participant used the mentorship opportunity; therefore, it is not discussed here. Twelve nurses completed all charge nurse classes and a simulation scenario of caring for a deteriorating infant. The nurses were given an opportunity to reflect on leadership practices after the simulation. Thematic analysis from qualitative, reflective data supported the enhanced understanding of managing complex patients, a code situation, and teams; guiding a team's novice nurse; leading as a charge nurse; and using clinical and critical thinking skills. All nurses reported that the simulation as experiential learning helped them to meet their leadership goals. Copyright 2015, SLACK Incorporated.

Evaluation of traffic signal timing optimization methods using a stochastic and microscopic simulation program.

DOT National Transportation Integrated Search

2003-01-01

This study evaluated existing traffic signal optimization programs including Synchro,TRANSYT-7F, and genetic algorithm optimization using real-world data collected in Virginia. As a first step, a microscopic simulation model, VISSIM, was extensively ...

STOVL aircraft simulation for integrated flight and propulsion control research

NASA Technical Reports Server (NTRS)

Mihaloew, James R.; Drummond, Colin K.

1989-01-01

The United States is in the initial stages of committing to a national program to develop a supersonic short takeoff and vertical landing (STOVL) aircraft. The goal of the propulsion community in this effort is to have the enabling propulsion technologies for this type aircraft in place to permit a low risk decision regarding the initiation of a research STOVL supersonic attack/fighter aircraft in the late mid-90's. This technology will effectively integrate, enhance, and extend the supersonic cruise, STOVL and fighter/attack programs to enable U.S. industry to develop a revolutionary supersonic short takeoff and vertical landing fighter/attack aircraft in the post-ATF period. A joint NASA Lewis and NASA Ames research program, with the objective of developing and validating technology for integrated-flight propulsion control design methodologies for short takeoff and vertical landing (STOVL) aircraft, was planned and is underway. This program, the NASA Supersonic STOVL Integrated Flight-Propulsion Controls Program, is a major element of the overall NASA-Lewis Supersonic STOVL Propulsion Technology Program. It uses an integrated approach to develop an integrated program to achieve integrated flight-propulsion control technology. Essential elements of the integrated controls research program are realtime simulations of the integrated aircraft and propulsion systems which will be used in integrated control concept development and evaluations. This paper describes pertinent parts of the research program leading up to the related realtime simulation development and remarks on the simulation structure to accommodate propulsion system hardware drop-in for real system evaluation.

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation. Appendix B: ROBSIM programmer's guide

NASA Technical Reports Server (NTRS)

Haley, D. C.; Almand, B. J.; Thomas, M. M.; Krauze, L. D.; Gremban, K. D.; Sanborn, J. C.; Kelly, J. H.; Depkovich, T. M.; Wolfe, W. J.; Nguyen, T.

1986-01-01

The purpose of the Robotic Simulation (ROBSIM) program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotic systems. ROBSIM is programmed in FORTRAM 77 and implemented on a VAX 11/750 computer using the VMS operating system. The programmer's guide describes the ROBSIM implementation and program logic flow, and the functions and structures of the different subroutines. With the manual and the in-code documentation, an experienced programmer can incorporate additional routines and modify existing ones to add desired capabilities.

Performance characteristics of three-phase induction motors

NASA Technical Reports Server (NTRS)

Wood, M. E.

1977-01-01

An investigation into the characteristics of three phase, 400 Hz, induction motors of the general type used on aircraft and spacecraft is summarized. Results of laboratory tests are presented and compared with results from a computer program. Representative motors were both tested and simulated under nominal conditions as well as off nominal conditions of temperature, frequency, voltage magnitude, and voltage balance. Good correlation was achieved between simulated and laboratory results. The primary purpose of the program was to verify the simulation accuracy of the computer program, which in turn will be used as an analytical tool to support the shuttle orbiter.

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation, appendix B

NASA Technical Reports Server (NTRS)

Haley, D. C.; Almand, B. J.; Thomas, M. M.; Krauze, L. D.; Gremban, K. D.; Sanborn, J. C.; Kelly, J. H.; Depkovich, T. M.

1984-01-01

The purpose of the Robotics Simulation (ROBSIM) program is to provide a broad range of computer capabilities to assist in the design, verification, simulation, and study of robotic systems. ROBSIM is programmed in FORTRAN 77 and implemented on a VAX 11/750 computer using the VMS operating system. This programmer's guide describes the ROBSIM implementation and program logic flow, and the functions and structures of the different subroutines. With this manual and the in-code documentation, and experienced programmer can incorporate additional routines and modify existing ones to add desired capabilities.

Monte Carlo simulation of X-ray imaging and spectroscopy experiments using quadric geometry and variance reduction techniques

NASA Astrophysics Data System (ADS)

Golosio, Bruno; Schoonjans, Tom; Brunetti, Antonio; Oliva, Piernicola; Masala, Giovanni Luca

2014-03-01

The simulation of X-ray imaging experiments is often performed using deterministic codes, which can be relatively fast and easy to use. However, such codes are generally not suitable for the simulation of even slightly more complex experimental conditions, involving, for instance, first-order or higher-order scattering, X-ray fluorescence emissions, or more complex geometries, particularly for experiments that combine spatial resolution with spectral information. In such cases, simulations are often performed using codes based on the Monte Carlo method. In a simple Monte Carlo approach, the interaction position of an X-ray photon and the state of the photon after an interaction are obtained simply according to the theoretical probability distributions. This approach may be quite inefficient because the final channels of interest may include only a limited region of space or photons produced by a rare interaction, e.g., fluorescent emission from elements with very low concentrations. In the field of X-ray fluorescence spectroscopy, this problem has been solved by combining the Monte Carlo method with variance reduction techniques, which can reduce the computation time by several orders of magnitude. In this work, we present a C++ code for the general simulation of X-ray imaging and spectroscopy experiments, based on the application of the Monte Carlo method in combination with variance reduction techniques, with a description of sample geometry based on quadric surfaces. We describe the benefits of the object-oriented approach in terms of code maintenance, the flexibility of the program for the simulation of different experimental conditions and the possibility of easily adding new modules. Sample applications in the fields of X-ray imaging and X-ray spectroscopy are discussed. Catalogue identifier: AERO_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AERO_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: GNU General Public License version 3 No. of lines in distributed program, including test data, etc.: 83617 No. of bytes in distributed program, including test data, etc.: 1038160 Distribution format: tar.gz Programming language: C++. Computer: Tested on several PCs and on Mac. Operating system: Linux, Mac OS X, Windows (native and cygwin). RAM: It is dependent on the input data but usually between 1 and 10 MB. Classification: 2.5, 21.1. External routines: XrayLib (https://github.com/tschoonj/xraylib/wiki) Nature of problem: Simulation of a wide range of X-ray imaging and spectroscopy experiments using different types of sources and detectors. Solution method: XRMC is a versatile program that is useful for the simulation of a wide range of X-ray imaging and spectroscopy experiments. It enables the simulation of monochromatic and polychromatic X-ray sources, with unpolarised or partially/completely polarised radiation. Single-element detectors as well as two-dimensional pixel detectors can be used in the simulations, with several acquisition options. In the current version of the program, the sample is modelled by combining convex three-dimensional objects demarcated by quadric surfaces, such as planes, ellipsoids and cylinders. The Monte Carlo approach makes XRMC able to accurately simulate X-ray photon transport and interactions with matter up to any order of interaction. The differential cross-sections and all other quantities related to the interaction processes (photoelectric absorption, fluorescence emission, elastic and inelastic scattering) are computed using the xraylib software library, which is currently the most complete and up-to-date software library for X-ray parameters. The use of variance reduction techniques makes XRMC able to reduce the simulation time by several orders of magnitude compared to other general-purpose Monte Carlo simulation programs. Running time: It is dependent on the complexity of the simulation. For the examples distributed with the code, it ranges from less than 1 s to a few minutes.

TIERRAS: A package to simulate high energy cosmic ray showers underground, underwater and under-ice

NASA Astrophysics Data System (ADS)

Tueros, Matías; Sciutto, Sergio

2010-02-01

In this paper we present TIERRAS, a Monte Carlo simulation program based on the well-known AIRES air shower simulations system that enables the propagation of particle cascades underground, providing a tool to study particles arriving underground from a primary cosmic ray on the atmosphere or to initiate cascades directly underground and propagate them, exiting into the atmosphere if necessary. We show several cross-checks of its results against CORSIKA, FLUKA, GEANT and ZHS simulations and we make some considerations regarding its possible use and limitations. The first results of full underground shower simulations are presented, as an example of the package capabilities. Program summaryProgram title: TIERRAS for AIRES Catalogue identifier: AEFO_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEFO_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 36 489 No. of bytes in distributed program, including test data, etc.: 3 261 669 Distribution format: tar.gz Programming language: Fortran 77 and C Computer: PC, Alpha, IBM, HP, Silicon Graphics and Sun workstations Operating system: Linux, DEC Unix, AIX, SunOS, Unix System V RAM: 22 Mb bytes Classification: 1.1 External routines: TIERRAS requires AIRES 2.8.4 to be installed on the system. AIRES 2.8.4 can be downloaded from http://www.fisica.unlp.edu.ar/auger/aires/eg_AiresDownload.html. Nature of problem: Simulation of high and ultra high energy underground particle showers. Solution method: Modification of the AIRES 2.8.4 code to accommodate underground conditions. Restrictions: In AIRES some processes that are not statistically significant on the atmosphere are not simulated. In particular, it does not include muon photonuclear processes. This imposes a limitation on the application of this package to a depth of 1 km of standard rock (or 2.5 km of water equivalent). Neutrinos are not tracked on the simulation, but their energy is taken into account in decays. Running time: A TIERRAS for AIRES run of a 10 eV shower with statistical sampling (thinning) below 10 eV and 0.2 weight factor (see [1]) uses approximately 1 h of CPU time on an Intel Core 2 Quad Q6600 at 2.4 GHz. It uses only one core, so 4 simultaneous simulations can be run on this computer. Aires includes a spooling system to run several simultaneous jobs of any type. References:S. Sciutto, AIRES 2.6 User Manual, http://www.fisica.unlp.edu.ar/auger/aires/.

A Modular Three-Dimensional Finite-Difference Ground-Water Flow Model

USGS Publications Warehouse

McDonald, Michael G.; Harbaugh, Arlen W.; Guo, Weixing; Lu, Guoping

1988-01-01

This report presents a finite-difference model and its associated modular computer program. The model simulates flow in three dimensions. The report includes detailed explanations of physical and mathematical concepts on which the model is based and an explanation of how those concepts are incorporated in the modular structure of the computer program. The modular structure consists of a Main Program and a series of highly independent subroutines called 'modules.' The modules are grouped into 'packages.' Each package deals with a specific feature of the hydrologic system which is to be simulated, such as flow from rivers or flow into drains, or with a specific method of solving linear equations which describe the flow system, such as the Strongly Implicit Procedure or Slice-Successive Overrelaxation. The division of the program into modules permits the user to examine specific hydrologic features of the model independently. This also facilita development of additional capabilities because new packages can be added to the program without modifying the existing packages. The input and output systems of the computer program are also designed to permit maximum flexibility. Ground-water flow within the aquifer is simulated using a block-centered finite-difference approach. Layers can be simulated as confined, unconfined, or a combination of confined and unconfined. Flow associated with external stresses, such as wells, areal recharge, evapotranspiration, drains, and streams, can also be simulated. The finite-difference equations can be solved using either the Strongly Implicit Procedure or Slice-Successive Overrelaxation. The program is written in FORTRAN 77 and will run without modification on most computers that have a FORTRAN 77 compiler. For each program ,module, this report includes a narrative description, a flow chart, a list of variables, and a module listing.

Evaluation of Laparoscopic Curricula in American Urology Residency Training: A 5-Year Update.

PubMed

Clements, Matthew B; Morrison, Kasey Y; Schenkman, Noah S

2016-03-01

Medical simulation offers the advantage of improving resident skill and comfort without impacting patient care. Five years ago, we identified trends in the use of robotic and laparoscopic simulation in 2008 and 2009 at American urology residency training programs. We seek to identify the changes in the use of simulators and the presence of formal curricula in the wake of technological advances and changes in graduate medical education. Attendees of the American Urological Association (AUA) Basic Sciences Course, mostly in their second or third year of residency, were surveyed on the availability and use of laparoscopic/robotic simulators at their program, the presence of a formal curriculum, and a Likert scale questionnaire regarding face and content validity. Over a 5-year period, the availability of virtual reality robotic simulators substantially increased from 14% to nearly 60% availability in 2013. Despite this increase, the frequency of simulator use remained unchanged (p = 0.40) and the reported presence of formal curricula decreased from 41% to 34.8%. There was no significant difference in simulator use between residents in programs with or without laparoscopic/robotic curricula (p = 0.95). There was also a decrease in the percentage of residents who felt official laparoscopic curricula (93%-81%) and simulators (82%-74%) should be involved in resident education. In the past 5 years, despite evidence supporting benefits from simulator use and increasing availability, self-reported resident use has remained unchanged and the reporting of presence of laparoscopic/robotic curricula has decreased. With more dedicated investment in formal curricula, residency training programs may receive greater returns on their simulator investments, improve resident skills and comfort, and ultimately improve the quality of patient care.

A comparison of the Landsat image and LAHARZ-simulated lahar inundation hazard zone by the 2010 Merapi eruption

NASA Astrophysics Data System (ADS)

Lee, Seul-Ki; Lee, Chang-Wook; Lee, Saro

2015-06-01

Located above the Java subduction zone, Merapi Volcano is an active stratovolcano with a volcanic activity cycle of 1-5 years. Most Merapi eruptions are relatively small with volcanic explosivity index (VEI) of 1-3. However, the most recent eruption, which occurred in 2010, was quite violent with a VEI of 4 and 386 people were killed. In this study, lahars and pyroclastic flow zones were detected using optical Landsat images and the lahar and pyroclastic flow zone simulated using the LAHARZ program. To detect areal extents of lahar and pyroclastic flows using Landsat images, supervised classification was performed after atmospheric correction by using a cosine of the solar zenith correction (COST) model. As a result, the extracted dimensions of pyroclastic flows are nearly identical to the Calatrava Volcanic Province (CVP) monthly reports. Then, areas of potential lahar and pyroclastic flow inundation based on flow volume using the LAHARZ program were simulated and mapped. Finally, the detected lahars and pyroclastic flow zones were compared with the simulated potential zones using LAHARZ program and verified. Results showed satisfactory similarity (55.63 %) between the detected and simulated zone. The simulated zones using the LAHARZ program can be used as an essential volcanic hazard map for preventing life and property damages for Merapi Volcano and other hazardous volcanic areas. Also, the LAHARZ program can be used to map volcano hazards in other hazardous volcanic areas.

Simulation of Behavioral Variations in the Submission of Student Financial Statements: Effects on BEOG Costs. Stage I Draft Final Report for the Study of Program Management Procedures in the Campus-Based and Basic Grant Programs. (Volume IV).

ERIC Educational Resources Information Center

Ellis, Richard

Volume IV of a study of program management procedures in the campus-based and Basic Educational Opportunity Grant (BEOG) programs deals with a set of simulated modifications in the statements made by BEOG applicants about their financial circumstances. Various kinds of misrepresentation of income, assets, and other factors are postulated, and the…

Lattice QCD simulations using the OpenACC platform

NASA Astrophysics Data System (ADS)

Majumdar, Pushan

2016-10-01

In this article we will explore the OpenACC platform for programming Graphics Processing Units (GPUs). The OpenACC platform offers a directive based programming model for GPUs which avoids the detailed data flow control and memory management necessary in a CUDA programming environment. In the OpenACC model, programs can be written in high level languages with OpenMP like directives. We present some examples of QCD simulation codes using OpenACC and discuss their performance on the Fermi and Kepler GPUs.

Chaste: A test-driven approach to software development for biological modelling

NASA Astrophysics Data System (ADS)

Pitt-Francis, Joe; Pathmanathan, Pras; Bernabeu, Miguel O.; Bordas, Rafel; Cooper, Jonathan; Fletcher, Alexander G.; Mirams, Gary R.; Murray, Philip; Osborne, James M.; Walter, Alex; Chapman, S. Jon; Garny, Alan; van Leeuwen, Ingeborg M. M.; Maini, Philip K.; Rodríguez, Blanca; Waters, Sarah L.; Whiteley, Jonathan P.; Byrne, Helen M.; Gavaghan, David J.

2009-12-01

Chaste ('Cancer, heart and soft-tissue environment') is a software library and a set of test suites for computational simulations in the domain of biology. Current functionality has arisen from modelling in the fields of cancer, cardiac physiology and soft-tissue mechanics. It is released under the LGPL 2.1 licence. Chaste has been developed using agile programming methods. The project began in 2005 when it was reasoned that the modelling of a variety of physiological phenomena required both a generic mathematical modelling framework, and a generic computational/simulation framework. The Chaste project evolved from the Integrative Biology (IB) e-Science Project, an inter-institutional project aimed at developing a suitable IT infrastructure to support physiome-level computational modelling, with a primary focus on cardiac and cancer modelling. Program summaryProgram title: Chaste Catalogue identifier: AEFD_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEFD_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: LGPL 2.1 No. of lines in distributed program, including test data, etc.: 5 407 321 No. of bytes in distributed program, including test data, etc.: 42 004 554 Distribution format: tar.gz Programming language: C++ Operating system: Unix Has the code been vectorised or parallelized?: Yes. Parallelized using MPI. RAM:<90 Megabytes for two of the scenarios described in Section 6 of the manuscript (Monodomain re-entry on a slab or Cylindrical crypt simulation). Up to 16 Gigabytes (distributed across processors) for full resolution bidomain cardiac simulation. Classification: 3. External routines: Boost, CodeSynthesis XSD, CxxTest, HDF5, METIS, MPI, PETSc, Triangle, Xerces Nature of problem: Chaste may be used for solving coupled ODE and PDE systems arising from modelling biological systems. Use of Chaste in two application areas are described in this paper: cardiac electrophysiology and intestinal crypt dynamics. Solution method: Coupled multi-physics with PDE, ODE and discrete mechanics simulation. Running time: The largest cardiac simulation described in the manuscript takes about 6 hours to run on a single 3 GHz core. See results section (Section 6) of the manuscript for discussion on parallel scaling.

Computer Recreations.

ERIC Educational Resources Information Center

Dewdney, A. K.

1988-01-01

Describes the creation of the computer program "BOUNCE," designed to simulate a weighted piston coming into equilibrium with a cloud of bouncing balls. The model follows the ideal gas law. Utilizes the critical event technique to create the model. Discusses another program, "BOOM," which simulates a chain reaction. (CW)

Computer Simulation of Human Service Program Evaluations.

ERIC Educational Resources Information Center

Trochim, William M. K.; Davis, James E.

1985-01-01

Describes uses of computer simulations for the context of human service program evaluation. Presents simple mathematical models for most commonly used human service outcome evaluation designs (pretest-posttest randomized experiment, pretest-posttest nonequivalent groups design, and regression-discontinuity design). Translates models into single…

Program to Optimize Simulated Trajectories (POST). Volume 2: Utilization manual

NASA Technical Reports Server (NTRS)

Bauer, G. L.; Cornick, D. E.; Habeger, A. R.; Petersen, F. M.; Stevenson, R.

1975-01-01

Information pertinent to users of the program to optimize simulated trajectories (POST) is presented. The input required and output available is described for each of the trajectory and targeting/optimization options. A sample input listing and resulting output are given.

An Ada Object Oriented Missile Flight Simulation

DTIC Science & Technology

1991-09-01

identify by block number) This thesis uses the Ada programming language in the design and development of an air-to-air missile flight simulation with...object oriented techniques and sound software engineering principles. The simulation is designed to be more understandable, modifiable, efficient and...Department of Computer Science ii ABSTRACT This thesis uses the Ada programming language in the design and development of an air-to-air missile flight

An Empirical Development of Parallelization Guidelines for Time-Driven Simulation

DTIC Science & Technology

1989-12-01

wives, who though not Cub fans, put on a good show during our trip, to waich some games . I would also like to recognize the help of my professors at...program parallelization. in this research effort a Ballistic Missile Defense (BMD) time driven simulation program, developed by DESE Research and...continuously, or continuously with discrete changes superimposed. The distinguishing feature of these simulations is the interaction between discretely

Utilization of Selected Simulation Games to Foster Improved Attitudes Among 11th Grade Students Engaged in the Study of Social Studies.

ERIC Educational Resources Information Center

Festa, Dominick A.

A project to determine the effectiveness of a program designed to create more positive attitudes among students studying social studies through use of simulation games is described in this dissertation. The purposes of the project were to describe the design and implementation of a plan for such a program and to determine whether simulation games…

Development of Ku-band rendezvous radar tracking and acquisition simulation programs

NASA Technical Reports Server (NTRS)

1986-01-01

The fidelity of the Space Shuttle Radar tracking simulation model was improved. The data from the Shuttle Orbiter Radar Test and Evaluation (SORTE) program experiments performed at the White Sands Missile Range (WSMR) were reviewed and analyzed. The selected flight rendezvous radar data was evaluated. Problems with the Inertial Line-of-Sight (ILOS) angle rate tracker were evaluated using the improved fidelity angle rate tracker simulation model.

Aquatic Contaminant and Mercury Simulation Modules Developed for Hydrologic and Hydraulic Models

DTIC Science & Technology

2016-07-01

through the food chain. Human health may also be affected by ingesting contaminated water or fish. As a result, the criteria for protecting human...ER D C/ EL T R- 16 -8 Environmental Quality Technology Research Program Aquatic Contaminant and Mercury Simulation Modules Developed...Quality Technology Research Program ERDC/EL TR-16-8 July 2016 Aquatic Contaminant and Mercury Simulation Modules Developed for Hydrologic and

Training Effectiveness Evaluation of Device A/F37A-T59

DTIC Science & Technology

1982-07-01

selected airplane by manually setting track, crosstrack, and altitude on thE control panel. Posi ion is maintained by flying the attitude director...simulator’s other design capabilities includes full SKE airdrop simulation, radar simulation, manual or pre-programmed malfunctions, a library of...during IFS testing, this feature was not available for this study. Thus, the instructors had to manually program all mission profiles prior to each

Implementation and evaluation of an interprofessional simulation-based education program for undergraduate nursing students in operating room nursing education: a randomized controlled trial.

PubMed

Wang, Rongmei; Shi, Nianke; Bai, Jinbing; Zheng, Yaguang; Zhao, Yue

2015-07-09

The present study was designed to implement an interprofessional simulation-based education program for nursing students and evaluate the influence of this program on nursing students' attitudes toward interprofessional education and knowledge about operating room nursing. Nursing students were randomly assigned to either the interprofessional simulation-based education or traditional course group. A before-and-after study of nursing students' attitudes toward the program was conducted using the Readiness for Interprofessional Learning Scale. Responses to an open-ended question were categorized using thematic content analysis. Nursing students' knowledge about operating room nursing was measured. Nursing students from the interprofessional simulation-based education group showed statistically different responses to four of the nineteen questions in the Readiness for Interprofessional Learning Scale, reflecting a more positive attitude toward interprofessional learning. This was also supported by thematic content analysis of the open-ended responses. Furthermore, nursing students in the simulation-based education group had a significant improvement in knowledge about operating room nursing. The integrated course with interprofessional education and simulation provided a positive impact on undergraduate nursing students' perceptions toward interprofessional learning and knowledge about operating room nursing. Our study demonstrated that this course may be a valuable elective option for undergraduate nursing students in operating room nursing education.

Launch Vehicle Ascent Trajectory Simulation Using the Program to Optimize Simulated Trajectories II (POST2)

NASA Technical Reports Server (NTRS)

Lugo, Rafael A.; Shidner, Jeremy D.; Powell, Richard W.; Marsh, Steven M.; Hoffman, James A.; Litton, Daniel K.; Schmitt, Terri L.

2017-01-01

The Program to Optimize Simulated Trajectories II (POST2) has been continuously developed for over 40 years and has been used in many flight and research projects. Recently, there has been an effort to improve the POST2 architecture by promoting modularity, flexibility, and ability to support multiple simultaneous projects. The purpose of this paper is to provide insight into the development of trajectory simulation in POST2 by describing methods and examples of various improved models for a launch vehicle liftoff and ascent.

Using artificial intelligence to control fluid flow computations

NASA Technical Reports Server (NTRS)

Gelsey, Andrew

1992-01-01

Computational simulation is an essential tool for the prediction of fluid flow. Many powerful simulation programs exist today. However, using these programs to reliably analyze fluid flow and other physical situations requires considerable human effort and expertise to set up a simulation, determine whether the output makes sense, and repeatedly run the simulation with different inputs until a satisfactory result is achieved. Automating this process is not only of considerable practical importance but will also significantly advance basic artificial intelligence (AI) research in reasoning about the physical world.

Establishing High-Quality Prostate Brachytherapy Using a Phantom Simulator Training Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thaker, Nikhil G.; Kudchadker, Rajat J.; Swanson, David A.

2014-11-01

Purpose: To design and implement a unique training program that uses a phantom-based simulator to teach the process of prostate brachytherapy (PB) quality assurance and improve the quality of education. Methods and Materials: Trainees in our simulator program were practicing radiation oncologists, radiation oncology residents, and fellows of the American Brachytherapy Society. The program emphasized 6 core areas of quality assurance: patient selection, simulation, treatment planning, implant technique, treatment evaluation, and outcome assessment. Using the Iodine 125 ({sup 125}I) preoperative treatment planning technique, trainees implanted their ultrasound phantoms with dummy seeds (ie, seeds with no activity). Pre- and postimplant dosimetric parametersmore » were compared and correlated using regression analysis. Results: Thirty-one trainees successfully completed the simulator program during the period under study. The mean phantom prostate size, number of seeds used, and total activity were generally consistent between trainees. All trainees met the V100 >95% objective both before and after implantation. Regardless of the initial volume of the prostate phantom, trainees' ability to cover the target volume with at least 100% of the dose (V100) was not compromised (R=0.99 pre- and postimplant). However, the V150 had lower concordance (R=0.37) and may better reflect heterogeneity control of the implant process. Conclusions: Analysis of implants from this phantom-based simulator shows a high degree of consistency between trainees and uniformly high-quality implants with respect to parameters used in clinical practice. This training program provides a valuable educational opportunity that improves the quality of PB training and likely accelerates the learning curve inherent in PB. Prostate phantom implantation can be a valuable first step in the acquisition of the required skills to safely perform PB.« less