Preliminary evaluation of a novel bone-conduction device for single-sided deafness.

PubMed

Popelka, Gerald R; Derebery, Jennifer; Blevins, Nikolas H; Murray, Michael; Moore, Brian C J; Sweetow, Robert W; Wu, Ben; Katsis, Mina

2010-04-01

A new intraoral bone-conduction device has advantages over existing bone-conduction devices for reducing the auditory deficits associated with single-sided deafness (SSD). Existing bone-conduction devices effectively mitigate auditory deficits from single-sided deafness but have suboptimal microphone locations, limited frequency range, and/or require invasive surgery. A new device has been designed to improve microphone placement (in the ear canal of the deaf ear), provide a wider frequency range, and eliminate surgery by delivering bone-conduction signals to the teeth via a removable oral appliance. Forces applied by the oral appliance were compared with forces typically experienced by the teeth from normal functions such as mastication or from other appliances. Tooth surface changes were measured on extracted teeth, and transducer temperature was measured under typical use conditions. Dynamic operating range, including gain, bandwidth, and maximum output limits, were determined from uncomfortable loudness levels and vibrotactile thresholds, and speech recognition scores were measured using normal-hearing subjects. Auditory performance in noise (Hearing in Noise Test) was measured in a limited sample of SSD subjects. Overall comfort, ease of insertion, and removal and visibility of the oral appliance in comparison with traditional hearing aids were measured using a rating scale. The oral appliance produces forces that are far below those experienced by the teeth from normal functions or conventional dental appliances. The bone-conduction signal level can be adjusted to prevent tactile perception yet provide sufficient gain and output at frequencies from 250 to 12,000 Hz. The device does not damage tooth surfaces nor produce heat, can be inserted and removed easily, and is as comfortable to wear as traditional hearing aids. The new microphone location has advantages for reducing the auditory deficits caused by SSD, including the potential to provide spatial cues introduced by reflections from the pinna, compared with microphone locations for existing devices. A new approach for SSD has been proposed that optimizes microphone location and delivers sound by bone conduction through a removable oral appliance. Measures in the laboratory using normal-hearing subjects indicate that the device provides useful gain and output for SSD patients, is comfortable, does not seem to have detrimental effects on oral function or oral health, and has several advantages over existing devices. Specifically, microphone placement is optimized for reducing the auditory deficit caused by SSD, frequency bandwidth is much greater, and the system does not require surgical placement. Auditory performance in a small sample of SSD subjects indicated a substantial advantage compared with not wearing the device. Future studies will involve performance measures on SSD patients wearing the device for longer periods.

Standalone medical device software: The evolving regulatory framework.

PubMed

McCarthy, Avril D; Lawford, Patricia V

2014-01-01

The paper provides an introduction to the regulatory landscape affecting a particular category of medical technology, namely standalone software-sometimes referred to as 'software as a medical device'. To aid the reader's comprehension of an often complex area, six case studies are outlined and discussed before the paper continues to provide detail of how software with a medical purpose in its own right can potentially be classified as a medical device. The reader is provided an appreciation of how to go about classifying such software and references to support the developer new to the field in locating detailed regulatory support documents and contact points for advice.

21 CFR 886.5900 - Electronic vision aid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Electronic vision aid. 886.5900 Section 886.5900...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5900 Electronic vision aid. (a) Identification. An electronic vision aid is an AC-powered or battery-powered device that consists of an...

21 CFR 886.5900 - Electronic vision aid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Electronic vision aid. 886.5900 Section 886.5900...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5900 Electronic vision aid. (a) Identification. An electronic vision aid is an AC-powered or battery-powered device that consists of an...

21 CFR 886.5900 - Electronic vision aid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Electronic vision aid. 886.5900 Section 886.5900...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5900 Electronic vision aid. (a) Identification. An electronic vision aid is an AC-powered or battery-powered device that consists of an...

21 CFR 886.5900 - Electronic vision aid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Electronic vision aid. 886.5900 Section 886.5900...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5900 Electronic vision aid. (a) Identification. An electronic vision aid is an AC-powered or battery-powered device that consists of an...

21 CFR 886.5900 - Electronic vision aid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Electronic vision aid. 886.5900 Section 886.5900...) MEDICAL DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5900 Electronic vision aid. (a) Identification. An electronic vision aid is an AC-powered or battery-powered device that consists of an...

21 CFR 886.5915 - Optical vision aid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Optical vision aid. 886.5915 Section 886.5915 Food... DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5915 Optical vision aid. (a) Identification. An optical vision aid is a device that consists of a magnifying lens with an accompanying AC-powered or...

21 CFR 886.5915 - Optical vision aid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Optical vision aid. 886.5915 Section 886.5915 Food... DEVICES OPHTHALMIC DEVICES Therapeutic Devices § 886.5915 Optical vision aid. (a) Identification. An optical vision aid is a device that consists of a magnifying lens with an accompanying AC-powered or...

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2014 CFR

2014-01-01

... mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.131 Do baggage liability limits apply to mobility aids and other assistive devices? With...

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2013 CFR

2013-01-01

... mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.131 Do baggage liability limits apply to mobility aids and other assistive devices? With...

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2012 CFR

2012-01-01

... mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.131 Do baggage liability limits apply to mobility aids and other assistive devices? With...

21 CFR 801.420 - Hearing aid devices; professional and patient labeling.

Code of Federal Regulations, 2010 CFR

2010-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES LABELING Special Requirements for Specific Devices § 801.420 Hearing aid devices; professional and patient labeling. (a) Definitions for the purposes of this section... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Hearing aid devices; professional and patient...

21 CFR 801.420 - Hearing aid devices; professional and patient labeling.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES LABELING Special Requirements for Specific Devices § 801.420 Hearing aid devices; professional and patient labeling. (a) Definitions for the purposes of this section... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Hearing aid devices; professional and patient...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false What mobility aids and other assistive... Aids, and Other Assistive Devices § 382.121 What mobility aids and other assistive devices may... or collapsible wheelchairs; (2) Other mobility aids, such as canes (including those used by persons...

14 CFR 382.129 - What other requirements apply when passengers' wheelchairs, other mobility aids, and other...

Code of Federal Regulations, 2013 CFR

2013-01-01

... passengers' wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage... Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.129 What other requirements apply when passengers' wheelchairs, other mobility aids, and other assistive devices must be...

14 CFR 382.129 - What other requirements apply when passengers' wheelchairs, other mobility aids, and other...

Code of Federal Regulations, 2012 CFR

2012-01-01

... passengers' wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage... Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.129 What other requirements apply when passengers' wheelchairs, other mobility aids, and other assistive devices must be...

14 CFR 382.129 - What other requirements apply when passengers' wheelchairs, other mobility aids, and other...

Code of Federal Regulations, 2014 CFR

2014-01-01

... passengers' wheelchairs, other mobility aids, and other assistive devices must be disassembled for stowage... Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.129 What other requirements apply when passengers' wheelchairs, other mobility aids, and other assistive devices must be...

Hearing aids: Do they help and, if so, how does one know?

NASA Astrophysics Data System (ADS)

Humes, Larry E.

2003-04-01

For those individuals with sensorineural hearing loss, ranging from mild to severe in degree, the conventional hearing aid is the most appropriate rehabilitative device available. Despite the fact that such devices have been available commercially for over 60 years, until recently, relatively little research has been directed at evaluating the effectiveness of these rehabilitative devices. How does one evaluate the effectiveness of a hearing aid as a rehabilitative device? Should effectiveness be based on the relative improvement in communication with and without the hearing aid, typically referred to as hearing-aid benefit, the satisfaction of the consumer with the device, or simply whether and how much the hearing aid is used? How are these aspects of hearing-aid effectiveness or outcome measured? Are the measures of hearing-aid outcome related to one another? What evidence is there regarding the effectiveness of contemporary hearing aids? Recent research regarding these and other related questions will be reviewed in this presentation. [Work supported, in part, by NIA.

21 CFR 874.3320 - Group hearing aid or group auditory trainer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Group hearing aid or group auditory trainer. 874... SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3320 Group hearing aid or group auditory trainer. (a) Identification. A group hearing aid or group auditory trainer...

21 CFR 874.3320 - Group hearing aid or group auditory trainer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Group hearing aid or group auditory trainer. 874... SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3320 Group hearing aid or group auditory trainer. (a) Identification. A group hearing aid or group auditory trainer...

21 CFR 874.3320 - Group hearing aid or group auditory trainer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Group hearing aid or group auditory trainer. 874... SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3320 Group hearing aid or group auditory trainer. (a) Identification. A group hearing aid or group auditory trainer...

21 CFR 874.3320 - Group hearing aid or group auditory trainer.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Group hearing aid or group auditory trainer. 874... SERVICES (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Prosthetic Devices § 874.3320 Group hearing aid or group auditory trainer. (a) Identification. A group hearing aid or group auditory trainer...

14 CFR 382.125 - What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive...

Code of Federal Regulations, 2012 CFR

2012-01-01

... wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo compartment? 382.125... Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.125 What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo...

14 CFR 382.125 - What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive...

Code of Federal Regulations, 2013 CFR

2013-01-01

... wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo compartment? 382.125... Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.125 What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo...

14 CFR 382.125 - What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive...

Code of Federal Regulations, 2014 CFR

2014-01-01

... wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo compartment? 382.125... Wheelchairs, Other Mobility Aids, and Other Assistive Devices § 382.125 What procedures do carriers follow when wheelchairs, other mobility aids, and other assistive devices must be stowed in the cargo...

An Analysis on Sensor Locations of the Human Body for Wearable Fall Detection Devices: Principles and Practice

PubMed Central

Özdemir, Ahmet Turan

2016-01-01

Wearable devices for fall detection have received attention in academia and industry, because falls are very dangerous, especially for elderly people, and if immediate aid is not provided, it may result in death. However, some predictive devices are not easily worn by elderly people. In this work, a huge dataset, including 2520 tests, is employed to determine the best sensor placement location on the body and to reduce the number of sensor nodes for device ergonomics. During the tests, the volunteer’s movements are recorded with six groups of sensors each with a triaxial (accelerometer, gyroscope and magnetometer) sensor, which is placed tightly on different parts of the body with special straps: head, chest, waist, right-wrist, right-thigh and right-ankle. The accuracy of individual sensor groups with their location is investigated with six machine learning techniques, namely the k-nearest neighbor (k-NN) classifier, Bayesian decision making (BDM), support vector machines (SVM), least squares method (LSM), dynamic time warping (DTW) and artificial neural networks (ANNs). Each technique is applied to single, double, triple, quadruple, quintuple and sextuple sensor configurations. These configurations create 63 different combinations, and for six machine learning techniques, a total of 63 × 6 = 378 combinations is investigated. As a result, the waist region is found to be the most suitable location for sensor placement on the body with 99.96% fall detection sensitivity by using the k-NN classifier, whereas the best sensitivity achieved by the wrist sensor is 97.37%, despite this location being highly preferred for today’s wearable applications. PMID:27463719

An Analysis on Sensor Locations of the Human Body for Wearable Fall Detection Devices: Principles and Practice.

PubMed

Özdemir, Ahmet Turan

2016-07-25

Wearable devices for fall detection have received attention in academia and industry, because falls are very dangerous, especially for elderly people, and if immediate aid is not provided, it may result in death. However, some predictive devices are not easily worn by elderly people. In this work, a huge dataset, including 2520 tests, is employed to determine the best sensor placement location on the body and to reduce the number of sensor nodes for device ergonomics. During the tests, the volunteer's movements are recorded with six groups of sensors each with a triaxial (accelerometer, gyroscope and magnetometer) sensor, which is placed tightly on different parts of the body with special straps: head, chest, waist, right-wrist, right-thigh and right-ankle. The accuracy of individual sensor groups with their location is investigated with six machine learning techniques, namely the k-nearest neighbor (k-NN) classifier, Bayesian decision making (BDM), support vector machines (SVM), least squares method (LSM), dynamic time warping (DTW) and artificial neural networks (ANNs). Each technique is applied to single, double, triple, quadruple, quintuple and sextuple sensor configurations. These configurations create 63 different combinations, and for six machine learning techniques, a total of 63 × 6 = 378 combinations is investigated. As a result, the waist region is found to be the most suitable location for sensor placement on the body with 99.96% fall detection sensitivity by using the k-NN classifier, whereas the best sensitivity achieved by the wrist sensor is 97.37%, despite this location being highly preferred for today's wearable applications.

Interactive pediatric emergency checklists to the palm of your hand - How the Pedi Crisis App traveled around the world.

PubMed

Gálvez, Jorge A; Lockman, Justin L; Schleelein, Laura E; Simpao, Allan F; Ahumada, Luis M; Wolf, Bryan A; Shah, Maully J; Heitmiller, Eugenie; Rehman, Mohamed

2017-08-01

Cognitive aids help clinicians manage critical events and have been shown to improve outcomes by providing critical information at the point of care. Critical event guidelines, such as the Society of Pediatric Anesthesia's Critical Events Checklists described in this article, can be distributed globally via interactive smartphone apps. From October 1, 2013 to January 1, 2014, we performed an observational study to determine the global distribution and utilization patterns of the Pedi Crisis cognitive aid app that the Society for Pediatric Anesthesia developed. We analyzed distribution and utilization metrics of individuals using Pedi Crisis on iOS (Apple Inc., Cupertino, CA) devices worldwide. We used Google Analytics software (Google Inc., Mountain View, CA) to monitor users' app activity (eg, screen views, user sessions). The primary outcome measurement was the number of user-sessions and geographic locations of Pedi Crisis user sessions. Each user was defined by the use of a unique Apple ID on an iOS device. Google Analytics correlates session activity with geographic location based on local Internet service provider logs. Pedi Crisis had 1 252 active users (both new and returning) and 4 140 sessions across 108 countries during the 3-month study period. Returning users used the app longer and viewed significantly more screens that new users (mean screen views: new users 1.3 [standard deviation +/-1.09, 95% confidence interval 1.22-1.55]; returning users 7.6 [standard deviation +/-4.19, 95% confidence interval 6.73-8.39]P<.01) CONCLUSIONS: Pedi Crisis was used worldwide within days of its release and sustained utilization beyond initial publication. The proliferation of handheld electronic devices provides a unique opportunity for professional societies to improve the worldwide dissemination of guidelines and evidence-based cognitive aids. © 2017 John Wiley & Sons Ltd.

78 FR 68861 - Certain Navigation Products, Including GPS Devices, Navigation and Display Systems, Radar Systems...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-15

... Devices, Navigation and Display Systems, Radar Systems, Navigational Aids, Mapping Systems and Related... navigation products, including GPS devices, navigation and display systems, radar systems, navigational aids..., radar systems, navigational aids, mapping systems and related software by reason of infringement of one...

78 FR 66940 - Regulatory Requirements for Hearing Aid Devices and Personal Sound Amplification Products; Draft...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-07

... DEPARTMENT OF HEALTH AND HUMAN SERVICES Food and Drug Administration [Docket No. FDA-2013-D-1295] Regulatory Requirements for Hearing Aid Devices and Personal Sound Amplification Products; Draft Guidance for... draft guidance entitled ``Regulatory Requirements for Hearing Aid Devices and Personal Sound...

MovAid- a novel device for advanced rehabilitation monitoring.

PubMed

Gupta, Prashant; Verma, Piyush; Gupta, Rakesh; Verma, Bhawna

2015-08-01

The present article introduces a new device "MovAid" which helps to measure and monitor rehabilitation. It has two main components- "MovAid device" and the "MovAid Smart Phone Application". The device connects wirelessly to the MovAid smart phone application via Bluetooth. It has electronic sensors to measure three important parameters of the patient- Angle of Joint Bent, Lift from the ground and Orientation of the limb. A mono-axis flex sensor to measure the degree of joint bent and a 3-axis accelerometer and gyroscope to measure the orientation of the limb and lift from the ground have been used. MovAid system bridges the gap between caretakers and patients, empowering both in ways never thought of before, by providing detailed and accurate data on every move.

34 CFR 300.113 - Routine checking of hearing aids and external components of surgically implanted medical devices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 34 Education 2 2012-07-01 2012-07-01 false Routine checking of hearing aids and external... Eligibility Other Fape Requirements § 300.113 Routine checking of hearing aids and external components of surgically implanted medical devices. (a) Hearing aids. Each public agency must ensure that hearing aids worn...

34 CFR 300.113 - Routine checking of hearing aids and external components of surgically implanted medical devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 34 Education 2 2014-07-01 2013-07-01 true Routine checking of hearing aids and external components... Eligibility Other Fape Requirements § 300.113 Routine checking of hearing aids and external components of surgically implanted medical devices. (a) Hearing aids. Each public agency must ensure that hearing aids worn...

34 CFR 300.113 - Routine checking of hearing aids and external components of surgically implanted medical devices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 34 Education 2 2013-07-01 2013-07-01 false Routine checking of hearing aids and external... Eligibility Other Fape Requirements § 300.113 Routine checking of hearing aids and external components of surgically implanted medical devices. (a) Hearing aids. Each public agency must ensure that hearing aids worn...

Virtual Reality: You Are There

NASA Technical Reports Server (NTRS)

1993-01-01

Telepresence or "virtual reality," allows a person, with assistance from advanced technology devices, to figuratively project himself into another environment. This technology is marketed by several companies, among them Fakespace, Inc., a former Ames Research Center contractor. Fakespace developed a teleoperational motion platform for transmitting sounds and images from remote locations. The "Molly" matches the user's head motion and, when coupled with a stereo viewing device and appropriate software, creates the telepresence experience. Its companion piece is the BOOM-the user's viewing device that provides the sense of involvement in the virtual environment. Either system may be used alone. Because suits, gloves, headphones, etc. are not needed, a whole range of commercial applications is possible, including computer-aided design techniques and virtual reality visualizations. Customers include Sandia National Laboratories, Stanford Research Institute and Mattel Toys.

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

14 CFR 141.41 - Flight simulators, flight training devices, and training aids.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., and training aids. 141.41 Section 141.41 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION... aids. An applicant for a pilot school certificate or a provisional pilot school certificate must show that its flight simulators, flight training devices, training aids, and equipment meet the following...

Modeling and simulation of tumor-influenced high resolution real-time physics-based breast models for model-guided robotic interventions

NASA Astrophysics Data System (ADS)

Neylon, John; Hasse, Katelyn; Sheng, Ke; Santhanam, Anand P.

2016-03-01

Breast radiation therapy is typically delivered to the patient in either supine or prone position. Each of these positioning systems has its limitations in terms of tumor localization, dose to the surrounding normal structures, and patient comfort. We envision developing a pneumatically controlled breast immobilization device that will enable the benefits of both supine and prone positioning. In this paper, we present a physics-based breast deformable model that aids in both the design of the breast immobilization device as well as a control module for the device during every day positioning. The model geometry is generated from a subject's CT scan acquired during the treatment planning stage. A GPU based deformable model is then generated for the breast. A mass-spring-damper approach is then employed for the deformable model, with the spring modeled to represent a hyperelastic tissue behavior. Each voxel of the CT scan is then associated with a mass element, which gives the model its high resolution nature. The subject specific elasticity is then estimated from a CT scan in prone position. Our results show that the model can deform at >60 deformations per second, which satisfies the real-time requirement for robotic positioning. The model interacts with a computer designed immobilization device to position the breast and tumor anatomy in a reproducible location. The design of the immobilization device was also systematically varied based on the breast geometry, tumor location, elasticity distribution and the reproducibility of the desired tumor location.

5 CFR 2416.103 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Assistant Attorney General, Civil Rights Division, United States Department of Justice. Auxiliary aids means... recordings, and other similar services and devices. Auxiliary aids useful for persons with impaired hearing include telephone handset amplifiers, telephones compatible with hearing aids, telecommunication devices...

Impact of Hearing Aid Technology on Outcomes in Daily Life I: the Patients’ Perspective

PubMed Central

Cox, Robyn M; Johnson, Jani A; Xu, Jingjing

2016-01-01

Objectives One of the challenges facing hearing care providers when recommending hearing aids is the choice of device technology level. Major manufacturers market families of hearing aids that are described as spanning the range from basic technology to premium technology. Premium technology hearing aids include acoustical processing capabilities (features) that are not found in basic technology instruments. These premium features are intended to yield improved hearing in daily life compared to basic-feature devices. However, independent research that establishes the incremental effectiveness of premium-feature devices compared to basic-feature devices is lacking. This research was designed to explore reported differences in hearing abilities for adults using premium-feature and basic-feature hearing aids in their daily lives. Design This was a single-blinded, repeated, crossover trial in which the participants were blinded. All procedures were carefully controlled to limit researcher bias. Forty-five participants used carefully fitted bilateral hearing aids for one month and then provided data to describe the hearing improvements or deficiencies noted in daily life. Typical participants were 70 years old with mild to moderate adult-onset hearing loss bilaterally. Each participant used 4 pairs of hearing aids: premium- and basic-feature devices from brands marketed by each of two major manufacturers. Participants were blinded about the devices they used and about the research questions. Results All of the outcomes were designed to capture the participant’s point of view about the benefits of the hearing aids. Three types of data were collected: change in hearing-related quality of life, extent of agreement with six positively worded statements about everyday hearing with the hearing aids, and reported preferences between the premium- and basic-feature devices from each brand as well as across all four research hearing aids combined. None of these measures yielded a statistically significant difference in outcomes between premium- and basic-feature devices. Participants did not report better outcomes with premium processing with any measure. Conclusions It could reasonably be asserted that the patient’s perspective is the gold standard for hearing aid effectiveness. While the acoustical processing provided by premium features can potentially improve scores on tests conducted in contrived conditions in a laboratory, or on specific items in a questionnaire, this does not ensure that the processing will be of noteworthy benefit when the hearing aid is used in the real world challenges faced by the patient. If evidence suggests the patient cannot detect that premium features yield improvements over basic features in daily life, what is the responsibility of the provider in recommending hearing aid technology level? In the current research, there was no evidence to suggest that premium-feature devices yielded better outcomes than basic-feature devices from the patient’s point of view. All of the research hearing aids were substantially, but equally, helpful. Further research is needed on this topic with other hearing aids and other manufacturers. In the meantime, providers should insist on scientifically credible independent evidence to support effectiveness claims for any hearing help devices. PMID:26881981

Students' Attitudes toward the Use of Hearing Aids in Al-Ahsa, Kingdom of Saudi Arabia

ERIC Educational Resources Information Center

Alodail, Abdullah Kholifh

2011-01-01

Hearing aid devices are worn within people's ears to help them hear the sounds around them. Teachers have to accept the use of hearing aids in the classroom as a device to assist students with hearing loss (Plumley, 2008). Further study is helpful to hearing aid research because it demonstrates the importance of hearing aid benefit awareness in…

Applications of ethylene vinyl acetate copolymers (EVA) in drug delivery systems.

PubMed

Schneider, Christian; Langer, Robert; Loveday, Donald; Hair, Dirk

2017-09-28

The potential for use of polymers in controlled drug delivery systems has been long recognized. Since their appearance in the literature, a wide range of degradable and non-degradable polymers have been demonstrated in drug delivery devices. The significance and features of ethylene-vinyl acetate (EVA) copolymers in initial research and development led to commercial drug delivery systems. This review examines the breadth of EVA use in drug delivery, and will aid the researcher in locating key references and experimental results, as well as understanding the features of EVA as a highly versatile, biocompatible polymer for drug delivery devices. Topics will include. Copyright © 2017 Elsevier B.V. All rights reserved.

Struggling to Hear? Tiny Devices Can Keep You Connected

MedlinePlus

... features. For example, some can connect to your mobile phone, TV, and other devices using Bluetooth technology. That ... Loss? Hearing Aids Hearing Loss and Hearing Aid Use (Infographic) Assistive Devices for People with Hearing, Voice, ...

Wearable ultrasonic guiding device with white cane for the visually impaired: A preliminary verisimilitude experiment.

PubMed

Cheng, Po-Hsun

2016-01-01

Several assistive technologies are available to help visually impaired individuals avoid obstructions while walking. Unfortunately, white canes and medical walkers are unable to detect obstacles on the road or react to encumbrances located above the waist. In this study, I adopted the cyber-physical system approach in the development of a cap-connected device to compensate for gaps in detection associated with conventional aids for the visually impaired. I developed a verisimilar, experimental route involving the participation of seven individuals with visual impairment, including straight sections, left turns, right turns, curves, and suspended objects. My aim was to facilitate the collection of information required for the practical use of the device. My findings demonstrate the feasibility of the proposed guiding device in alerting walkers to the presence of some kinds of obstacles from the small number of subjects. That is, it shows promise for future work and research with the proposed device. My findings provide a valuable reference for the further improvement of these devices as well as the establishment of experiments involving the visually impaired.

Orthodontics: computer-aided diagnosis and treatment planning

NASA Astrophysics Data System (ADS)

Yi, Yaxing; Li, Zhongke; Wei, Suyuan; Deng, Fanglin; Yao, Sen

2000-10-01

The purpose of this article is to introduce the outline of our newly developed computer-aided 3D dental cast analyzing system with laser scanning, and its preliminary clinical applications. The system is composed of a scanning device and a personal computer as a scanning controller and post processor. The scanning device is composed of a laser beam emitter, two sets of linear CCD cameras and a table which is rotatable by two-degree-of-freedom. The rotating is controlled precisely by a personal computer. The dental cast is projected and scanned with a laser beam. Triangulation is applied to determine the location of each point. Generation of 3D graphics of the dental cast takes approximately 40 minutes. About 170,000 sets of X,Y,Z coordinates are store for one dental cast. Besides the conventional linear and angular measurements of the dental cast, we are also able to demonstrate the size of the top surface area of each molar. The advantage of this system is that it facilitates the otherwise complicated and time- consuming mock surgery necessary for treatment planning in orthognathic surgery.

30 CFR 77.1707 - First aid equipment; location; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false First aid equipment; location; minimum... OF UNDERGROUND COAL MINES Miscellaneous § 77.1707 First aid equipment; location; minimum requirements. (a) Each operator of a surface coal mine shall maintain a supply of the first aid equipment set forth...

Characterization of Personal Privacy Devices (PPD) radiation pattern impact on the ground and airborne segments of the local area augmentation system (LAAS) at GPS L1 frequency

NASA Astrophysics Data System (ADS)

Alkhateeb, Abualkair M. Khair

Personal Privacy Devices (PPDs) are radio-frequency transmitters that intentionally transmit in a frequency band used by other devices for the intent purpose of denying service to those devices. These devices have shown the potential to interfere with the ground and air sub-systems of the Local Area Augmentation Systems (LAAS), a GPS-based navigation aids at commercial airports. The Federal Aviation Administration (FAA) is concerned by the potential impact of these devices to GPS navigation aids at airports and has commenced an activity to determine the severity of this threat. In support of this situation, the research in this dissertation has been conducted under (FAA) Cooperative Agreement 2011-G-012, to investigate the impact of these devices on the LAAS. In order to investigate the impact of PPDs Radio Frequency Interference (RFI) on the ground and air sub-systems of the LAAS, the work presented in phase one of this research is intended to characterize the vehicle's impact on the PPD's Effective Isotropic Radiated Power (EIRP). A study was conceived in this research to characterize PPD performance by examining the on-vehicle radiation patterns as a function of vehicle type, jammer type, jammer location inside a vehicle and jammer orientation at each location. Phase two was to characterize the GPS Radiation Pattern on Multipath Limiting Antenna. MLA has to meet stringent requirements for acceptable signal detection and multipath rejection. The ARL-2100 is the most recent MLA antenna proposed to be used in the LAAS ground segment. The ground-based antenna's radiation pattern was modeled. This was achieved via (HFSS) a commercial-off the shelf CAD-based modeling code with a full-wave electromagnetic software simulation package that uses the Finite Element Analysis. Phase three of this work has been conducted to study the characteristics of the GPS Radiation Pattern on Commercial Aircraft. The airborne GPS antenna was modeled and the resulting radiation pattern on a Bombardier Global 5000 commercial full aircraft was studied. This was achieved via CAD-based modeling with a full-wave electromagnetic software simulation package (FEKO). It is important because the aircraft comes in approach on a 3° glideslope angle. Elevation relative to PPD jammer is changing.

23 CFR 655.605 - Project procedures.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Project procedures. 655.605 Section 655.605 Highways... OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.605 Project procedures. (a) Federal-aid highways. Federal-aid projects involving the installation of traffic control devices...

23 CFR 655.605 - Project procedures.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 23 Highways 1 2012-04-01 2012-04-01 false Project procedures. 655.605 Section 655.605 Highways... OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.605 Project procedures. (a) Federal-aid highways. Federal-aid projects involving the installation of traffic control devices...

23 CFR 655.605 - Project procedures.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Project procedures. 655.605 Section 655.605 Highways... OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.605 Project procedures. (a) Federal-aid highways. Federal-aid projects involving the installation of traffic control devices...

23 CFR 655.605 - Project procedures.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Project procedures. 655.605 Section 655.605 Highways... OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.605 Project procedures. (a) Federal-aid highways. Federal-aid projects involving the installation of traffic control devices...

23 CFR 655.605 - Project procedures.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Project procedures. 655.605 Section 655.605 Highways... OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.605 Project procedures. (a) Federal-aid highways. Federal-aid projects involving the installation of traffic control devices...

Medical Devices; Immunology and Microbiology Devices; Classification of the Device To Detect and Measure Non-Microbial Analyte(s) in Human Clinical Specimens To Aid in Assessment of Patients With Suspected Sepsis. Final order.

PubMed

2017-10-24

The Food and Drug Administration (FDA or we) is classifying the device to detect and measure non-microbial analyte(s) in human clinical specimens to aid in assessment of patients with suspected sepsis into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the device to detect and measure non-microbial analyte(s) in human clinical specimens to aid in assessment of patients with suspected sepsis's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

30 CFR 75.1713-7 - First-aid equipment; location; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false First-aid equipment; location; minimum... § 75.1713-7 First-aid equipment; location; minimum requirements. (a) Each operator of an underground coal mine shall maintain a supply of the first-aid equipment set forth in paragraph (b) of this § 75...

Speech perception benefits of FM and infrared devices to children with hearing aids in a typical classroom.

PubMed

Anderson, Karen L; Goldstein, Howard

2004-04-01

Children typically learn in classroom environments that have background noise and reverberation that interfere with accurate speech perception. Amplification technology can enhance the speech perception of students who are hard of hearing. This study used a single-subject alternating treatments design to compare the speech recognition abilities of children who are, hard of hearing when they were using hearing aids with each of three frequency modulated (FM) or infrared devices. Eight 9-12-year-olds with mild to severe hearing loss repeated Hearing in Noise Test (HINT) sentence lists under controlled conditions in a typical kindergarten classroom with a background noise level of +10 dB signal-to-noise (S/N) ratio and 1.1 s reverberation time. Participants listened to HINT lists using hearing aids alone and hearing aids in combination with three types of S/N-enhancing devices that are currently used in mainstream classrooms: (a) FM systems linked to personal hearing aids, (b) infrared sound field systems with speakers placed throughout the classroom, and (c) desktop personal sound field FM systems. The infrared ceiling sound field system did not provide benefit beyond that provided by hearing aids alone. Desktop and personal FM systems in combination with personal hearing aids provided substantial improvements in speech recognition. This information can assist in making S/N-enhancing device decisions for students using hearing aids. In a reverberant and noisy classroom setting, classroom sound field devices are not beneficial to speech perception for students with hearing aids, whereas either personal FM or desktop sound field systems provide listening benefits.

Clinical Verification of Image Warping as a Potential Aid for the Visually Handicapped

NASA Technical Reports Server (NTRS)

Loshin, David

1996-01-01

The bulk of this research was to designed determine potential of the Programmable Remapper (PR) as a device to enhance vision for the visually handicapped. This research indicated that remapping would have potential as a low vision device if the eye position could be monitored with feedback to specify the proper location of the remapped image. This must be accomplished at high rate so that there is no lag of the image behind the eye position. Since at this time, there is no portable eye monitor device (at a reasonable cost) that will operate under the required conditions, it would not be feasible to continue with remapping experiments for patients with central field defects. However, since patients with peripheral field defects do not have the same eye positioning requirements, they may indeed benefit from this technology. Further investigations must be performed to determine plausibility of this application of remapping.

An evaluation of the performance of two binaural beamformers in complex and dynamic multitalker environments.

PubMed

Best, Virginia; Mejia, Jorge; Freeston, Katrina; van Hoesel, Richard J; Dillon, Harvey

2015-01-01

Binaural beamformers are super-directional hearing aids created by combining microphone outputs from each side of the head. While they offer substantial improvements in SNR over conventional directional hearing aids, the benefits (and possible limitations) of these devices in realistic, complex listening situations have not yet been fully explored. In this study we evaluated the performance of two experimental binaural beamformers. Testing was carried out using a horizontal loudspeaker array. Background noise was created using recorded conversations. Performance measures included speech intelligibility, localization in noise, acceptable noise level, subjective ratings, and a novel dynamic speech intelligibility measure. Participants were 27 listeners with bilateral hearing loss, fitted with BTE prototypes that could be switched between conventional directional or binaural beamformer microphone modes. Relative to the conventional directional microphones, both binaural beamformer modes were generally superior for tasks involving fixed frontal targets, but not always for situations involving dynamic target locations. Binaural beamformers show promise for enhancing listening in complex situations when the location of the source of interest is predictable.

An evaluation of the performance of two binaural beamformers in complex and dynamic multitalker environments

PubMed Central

Best, Virginia; Mejia, Jorge; Freeston, Katrina; van Hoesel, Richard J.; Dillon, Harvey

2016-01-01

Objective Binaural beamformers are super-directional hearing aids created by combining microphone outputs from each side of the head. While they offer substantial improvements in SNR over conventional directional hearing aids, the benefits (and possible limitations) of these devices in realistic, complex listening situations have not yet been fully explored. In this study we evaluated the performance of two experimental binaural beamformers. Design Testing was carried out using a horizontal loudspeaker array. Background noise was created using recorded conversations. Performance measures included speech intelligibility, localisation in noise, acceptable noise level, subjective ratings, and a novel dynamic speech intelligibility measure. Study sample Participants were 27 listeners with bilateral hearing loss, fitted with BTE prototypes that could be switched between conventional directional or binaural beamformer microphone modes. Results Relative to the conventional directional microphones, both binaural beamformer modes were generally superior for tasks involving fixed frontal targets, but not always for situations involving dynamic target locations. Conclusions Binaural beamformers show promise for enhancing listening in complex situations when the location of the source of interest is predictable. PMID:26140298

Applications of direct-to-consumer hearing devices for adults with hearing loss: a review

PubMed Central

Manchaiah, Vinaya; Taylor, Brian; Dockens, Ashley L; Tran, Nicole R; Lane, Kayla; Castle, Mariana; Grover, Vibhu

2017-01-01

Background This systematic literature review is aimed at investigating applications of direct-to-consumer hearing devices for adults with hearing loss. This review discusses three categories of direct-to-consumer hearing devices: 1) personal sound amplification products (PSAPs), 2) direct-mail hearing aids, and 3) over-the-counter (OTC) hearing aids. Method A literature review was conducted using EBSCOhost and included the databases CINAHL, MEDLINE, and PsycINFO. After applying prior agreed inclusion and exclusion criteria, 13 reports were included in the review. Results Included studies fell into three domains: 1) electroacoustic characteristics, 2) consumer surveys, and 3) outcome evaluations. Electroacoustic characteristics of these devices vary significantly with some meeting the stringent acoustic criteria used for hearing aids, while others producing dangerous output levels (ie, over 120-dB sound pressure level). Low-end (or low-cost) devices were typically poor in acoustic quality and did not meet gain levels necessary for most adult and elderly hearing loss patterns (eg, presbycusis), especially in high frequencies. Despite direct-mail hearing aids and PSAPs being associated with lower satisfaction when compared to hearing aids purchased through hearing health care professionals, consumer surveys suggest that 5%–19% of people with hearing loss purchase hearing aids through direct-mail or online. Studies on outcome evaluation suggest positive outcomes of OTC devices in the elderly population. Of note, OTC outcomes appear better when a hearing health care professional supports these users. Conclusion While some direct-to-consumer hearing devices have the capability to produce adverse effects due to production of dangerously high sound levels and internal noise, the existing literature suggests that there are potential benefits of these devices. Research of direct-to-consumer hearing devices is limited, and current published studies are of weak quality. Much effort is needed to understand the benefits and limitations of such devices on people with hearing loss. PMID:28553093

Applications of direct-to-consumer hearing devices for adults with hearing loss: a review.

PubMed

Manchaiah, Vinaya; Taylor, Brian; Dockens, Ashley L; Tran, Nicole R; Lane, Kayla; Castle, Mariana; Grover, Vibhu

2017-01-01

This systematic literature review is aimed at investigating applications of direct-to-consumer hearing devices for adults with hearing loss. This review discusses three categories of direct-to-consumer hearing devices: 1) personal sound amplification products (PSAPs), 2) direct-mail hearing aids, and 3) over-the-counter (OTC) hearing aids. A literature review was conducted using EBSCOhost and included the databases CINAHL, MEDLINE, and PsycINFO. After applying prior agreed inclusion and exclusion criteria, 13 reports were included in the review. Included studies fell into three domains: 1) electroacoustic characteristics, 2) consumer surveys, and 3) outcome evaluations. Electroacoustic characteristics of these devices vary significantly with some meeting the stringent acoustic criteria used for hearing aids, while others producing dangerous output levels (ie, over 120-dB sound pressure level). Low-end (or low-cost) devices were typically poor in acoustic quality and did not meet gain levels necessary for most adult and elderly hearing loss patterns (eg, presbycusis), especially in high frequencies. Despite direct-mail hearing aids and PSAPs being associated with lower satisfaction when compared to hearing aids purchased through hearing health care professionals, consumer surveys suggest that 5%-19% of people with hearing loss purchase hearing aids through direct-mail or online. Studies on outcome evaluation suggest positive outcomes of OTC devices in the elderly population. Of note, OTC outcomes appear better when a hearing health care professional supports these users. While some direct-to-consumer hearing devices have the capability to produce adverse effects due to production of dangerously high sound levels and internal noise, the existing literature suggests that there are potential benefits of these devices. Research of direct-to-consumer hearing devices is limited, and current published studies are of weak quality. Much effort is needed to understand the benefits and limitations of such devices on people with hearing loss.

Analysis of a Memory Device Failure

NASA Technical Reports Server (NTRS)

Nicolas, David P.; Devaney, John; Gores, Mark; Dicken, Howard

1998-01-01

The recent failure of a vintage memory device presented a unique challenge to failure analysts. Normally device layouts, fabrication parameters and other technical information were available to assist the analyst in the analysis. However, this device was out of production for many years and the manufacturer was no longer in business, so the information was not available. To further complicate this analysis, the package leads were all but removed making additional electrical testing difficult. Under these conditions, new and innovative methods were used to analyze the failure. The external visual exam, radiography, PIND, and leak testing were performed with nominal results. Since electrical testing was precluded by the short lead lengths, the device was delidded to expose the internal structures for microscopic examination. No failure mechanism was identified. The available electrical data suggested an ESD or low level EOS type mechanism which left no visible surface damage. Due to parallel electrical paths, electrical probing on the chip failed to locate the failure site. Two non-destructive Scanning Electron Microscopy techniques, CIVA (Charge Induced Voltage Alteration) and EBIC (Electron Beam Induced Current), and a liquid crystal decoration technique which detects localized heating were employed to aid in the analysis. CIVA and EBIC isolated two faults in the input circuitry, and the liquid crystal technique further localized two hot spots in regions on two input gates. Removal of the glassivation and metallization revealed multiple failure sites located in the gate oxide of two input transistors suggesting machine (testing) induced damage.

Directional Hearing Aid

NASA Technical Reports Server (NTRS)

Jhabvala, M.; Lin, H. C.

1989-01-01

Hearing-aid device indicates visually whether sound is coming from left, right, back, or front. Device intended to assist individuals who are deaf in at least one ear and unable to discern naturally directions to sources of sound. Device promotes safety in street traffic, on loading docks, and in presence of sirens, alarms, and other warning sounds. Quadraphonic version of device built into pair of eyeglasses and binaural version built into visor.

Dichotic Hearing in Elderly Hearing Aid Users Who Choose to Use a Single-Ear Device

PubMed Central

Ribas, Angela; Mafra, Nicoli; Marques, Jair; Mottecy, Carla; Silvestre, Renata; Kozlowski, Lorena

2014-01-01

Introduction Elderly individuals with bilateral hearing loss often do not use hearing aids in both ears. Because of this, dichotic tests to assess hearing in this group may help identify peculiar degenerative processes of aging and hearing aid selection. Objective To evaluate dichotic hearing for a group of elderly hearing aid users who did not adapt to using binaural devices and to verify the correlation between ear dominance and the side chosen to use the device. Methods A cross-sectional descriptive study involving 30 subjects from 60 to 81 years old, of both genders, with an indication for bilateral hearing aids for over 6 months, but using only a single device. Medical history, pure tone audiometry, and dichotic listening tests were all completed. Results All subjects (100%) of the sample failed the dichotic digit test; 94% of the sample preferred to use the device in one ear because bilateral use bothered them and affected speech understanding. In 6%, the concern was aesthetics. In the dichotic digit test, there was significant predominance of the right ear over the left, and there was a significant correlation between the dominant side with the ear chosen by the participant for use of the hearing aid. Conclusion In elderly subjects with bilateral hearing loss who have chosen to use only one hearing aid, there is dominance of the right ear over the left in dichotic listening tasks. There is a correlation between the dominant ear and the ear chosen for hearing aid fitting. PMID:25992120

Invisible Flame Imaging

NASA Technical Reports Server (NTRS)

1997-01-01

Stennis Space Center uses more than one million gallons of liquid hydrogen per month in its rocket testing program. Firefighters responding to a hydrogen fire had to give the area "the broom test" to determine the presence and location of a fire. This technique has significant safety and accuracy shortfalls. Stennis then developed technology to visually assess the presence, location and extent of hydrogen fires. SafetyScan, LLC. is now manufacturing FIRESCAPE, the first affordable commercial product for invisible (or ashless) fire imaging based on the original technology, to aid firefighters in seeing the invisible flames from alcohol and hydrogen fires during the day and even through smoke. The hand-held device weighs five pounds, is used like a pair of binoculars and can run for up to two hours before recharging.

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false Do baggage liability limits apply to mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive...

14 CFR 382.131 - Do baggage liability limits apply to mobility aids and other assistive devices?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false Do baggage liability limits apply to mobility aids and other assistive devices? 382.131 Section 382.131 Aeronautics and Space OFFICE OF THE... BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility Aids, and Other Assistive...

Beyond the hearing aid: Assistive listening devices

NASA Astrophysics Data System (ADS)

Holmes, Alice E.

2003-04-01

Persons with hearing loss can obtain great benefit from hearing aids but there are many situations that traditional amplification devices will not provide enough help to ensure optimal communication. Assistive listening and signaling devices are designed to improve the communication of the hearing impaired in instances where traditional hearing aids are not sufficient. These devices are designed to help with problems created by listening in noise or against a competing message, improve distance listening, facilitate group conversation (help with problems created by rapidly changing speakers), and allow independence from friends and family. With the passage of the Americans with Disabilities Act in 1990, assistive listening devices (ALDs) are becoming more accessible to the public with hearing loss. Employers and public facilities must provide auxiliary aids and services when necessary to ensure effective communication for persons who are deaf or hard of hearing. However many professionals and persons with hearing loss are unaware of the various types and availability of ALDs. An overview of ALDs along with a discussion of their advantages and disadvantages will be given.

Understanding history, philanthropy and the role of WHO in provision of assistive technologies for hearing loss.

PubMed

Chadha, Shelly; Moussy, Francis; Friede, Martin Howell

2014-09-01

Philanthropy continues to play an important role in provision of hearing devices and is often the only alternative for the majority of those in need of these devices. While this leads to improved access to services it may also create unsustainable service delivery models. Over the past decade, World Health Organization (WHO) has been making consistent efforts towards promoting accessibility and affordability of high-quality hearing devices, especially in Low- and Middle-Income Countries (LMIC). WHO developed and updated the "Guidelines for Hearing Aids and Services in Developing Countries", in 2004. In 2006, WHO supported the establishment of "World Wide (WW) Hearing", to promote hearing aid access across the globe. In the past year, WHO has renewed these efforts. As the first step and following a consultation on promoting access to hearing devices, WHO has developed a preferred product profile in order to facilitate the development and access of appropriate and affordable hearing aids for developing countries. The Convention on the Rights of Persons with Disabilities (article 32), calls for international collaboration to promote access to assistive technology including hearing devices. A coordinated global effort is required to promote availability and affordability of high-quality hearing devices. Such an undertaking requires the cooperation of all stakeholders: WHO, Member States, Non-Governmental Organizations (NGOs), philanthropists, manufacturers and users, to fulfill the international obligation and bring about a change in the quality of life of millions of people with hearing loss. Development of preferred product profile for hearing aids in LMICs can improve development and provision of high-quality, affordable hearing devices. Investment made by the recipients, such as partial financial contribution towards the cost of device or through purchase of ear mould or batteries, leads to a greater sense of responsibility towards the device and its maintenance. Low level of awareness about hearing loss and the potential benefits of hearing aids contribute to the underutilization of hearing aids.

Survey of driver aid devices for improved fuel economy.

DOT National Transportation Integrated Search

1976-11-30

This report presents a brief summarization of available information pertaining to devices offered to aid the driver in improving his driving habits in order to reduce fuel consumption. Principal emphasis is placed on characterizing the available devi...

Anatomy of the Human Ear/Questions to Ask your Hearing Professional

MedlinePlus

... disorders A severe blow to the head Loud noise Assistive Devices Hearing Aids —Small electronic devices worn ... or without hearing aids to overcome distance, background noise, or poor room acoustics. An example is a ...

28 CFR 36.303 - Auxiliary aids and services.

Code of Federal Regulations, 2010 CFR

2010-07-01

...” includes— (1) Qualified interpreters, notetakers, computer-aided transcription services, written materials... equipment or devices; and (4) Other similar services and actions. (c) Effective communication. A public... communication with individuals with disabilities. (d) Telecommunication devices for the deaf (TDD's). (1) A...

Computer-aided engineering of semiconductor integrated circuits

NASA Astrophysics Data System (ADS)

Meindl, J. D.; Dutton, R. W.; Gibbons, J. F.; Helms, C. R.; Plummer, J. D.; Tiller, W. A.; Ho, C. P.; Saraswat, K. C.; Deal, B. E.; Kamins, T. I.

1980-07-01

Economical procurement of small quantities of high performance custom integrated circuits for military systems is impeded by inadequate process, device and circuit models that handicap low cost computer aided design. The principal objective of this program is to formulate physical models of fabrication processes, devices and circuits to allow total computer-aided design of custom large-scale integrated circuits. The basic areas under investigation are (1) thermal oxidation, (2) ion implantation and diffusion, (3) chemical vapor deposition of silicon and refractory metal silicides, (4) device simulation and analytic measurements. This report discusses the fourth year of the program.

The development of an observational screening tool to assess safe, effective and appropriate walking aid use in people with multiple sclerosis.

PubMed

Eitzen, Abby; Finlayson, Marcia; Carolan-Laing, Leanne; Nacionales, Arthur Junn; Walker, Christie; O'Connor, Josephine; Asano, Miho; Coote, Susan

2017-08-01

The purpose of this study was to identify potential items for an observational screening tool to assess safe, effective and appropriate walking aid use among people with multiple sclerosis (MS). Such a tool is needed because of the association between fall risk and mobility aid use in this population. Four individuals with MS were videotaped using a one or two straight canes, crutches or a rollator in different settings. Seventeen health care professionals from Canada, Ireland and the United States were recruited, and viewed the videos, and were then interviewed about the use of the devices by the individuals in the videos. Interview questions addressed safety, effectiveness and appropriateness of the device in the setting. Data were analyzed qualitatively. Coding consistency across raters was evaluated and confirmed. Nineteen codes were identified as possible items for the screening tool. The most frequent issues raised regardless of setting and device were "device used for duration/abandoned", "appropriate device", "balance and stability", "device technique", "environmental modification" and "hands free." With the identification of a number of potential tool items, researchers can now move forward with the development of the tool. This will involve consultation with both healthcare professionals and people with MS. Implications for rehabilitation Falls among people with multiple sclerosis are associated with mobility device use and use of multiple devices is associated with greater falls risk. The ability to assess for safe, effective and efficient use of walking aids is therefore important, no tools currently exist for this purpose. The codes arising from this study will be used to develop a screening tool for safe, effective and efficient walking aid use with the aim of reducing falls risk.

Multi-microphone adaptive array augmented with visual cueing.

PubMed

Gibson, Paul L; Hedin, Dan S; Davies-Venn, Evelyn E; Nelson, Peggy; Kramer, Kevin

2012-01-01

We present the development of an audiovisual array that enables hearing aid users to converse with multiple speakers in reverberant environments with significant speech babble noise where their hearing aids do not function well. The system concept consists of a smartphone, a smartphone accessory, and a smartphone software application. The smartphone accessory concept is a multi-microphone audiovisual array in a form factor that allows attachment to the back of the smartphone. The accessory will also contain a lower power radio by which it can transmit audio signals to compatible hearing aids. The smartphone software application concept will use the smartphone's built in camera to acquire images and perform real-time face detection using the built-in face detection support of the smartphone. The audiovisual beamforming algorithm uses the location of talking targets to improve the signal to noise ratio and consequently improve the user's speech intelligibility. Since the proposed array system leverages a handheld consumer electronic device, it will be portable and low cost. A PC based experimental system was developed to demonstrate the feasibility of an audiovisual multi-microphone array and these results are presented.

MISSIONS: The Mobile-Based Disaster Mitigation System in Indonesia

NASA Astrophysics Data System (ADS)

Passarella, Rossi; Putri Raflesia, Sarifah; Lestarini, Dinda; Rifai, Ahmad; Veny, Harumi

2018-04-01

Disaster mitigation is essential to minimize the effects of disasters. Indonesia is one of the disaster prone areas in Asia and the government explores the usage of Information technology (IT) to aid its mitigation efforts. Currently, there are Indonesian websites which hold information regarding the weather monitoring, climate conditions, and geophysics. But, there is no clear indicator of mitigation efforts or things to do during an emergency. Therefore, this research proposed MISSIONS, a disaster mitigation model using geo-fencing technique to detect the location of the users through their mobile devices. MISSIONS uses mobile-based disaster mitigation system as a way to disseminate critical information to victims during emergency when they are in disaster zones using virtual fences. It aims to help the government to reduce the effects of disaster and aid in the mitigation efforts. The implementation result shows that MISSIONS have a high accuracy in detecting user whereabouts.

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

21 CFR 874.3300 - Hearing Aid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... generic type of device includes the air-conduction hearing aid and the bone-conduction hearing aid, but... subpart E of part 807 of this chapter subject to § 874.9. (2) Class II for the bone-conduction hearing aid...

Factors affecting the use and perceived benefit of ITE and BTE hearing aids.

PubMed

Baumfield, A; Dillon, H

2001-08-01

The aim of the present study was to investigate factors that might affect hearing aid use, satisfaction and perceived benefit. A further aim was to look at which variables affect the choice of hearing aid, in particular, an in-the-ear (ITE) versus a behind-the-ear (BTE) device. Twenty-nine elderly hearing-impaired people with a mild-to-moderate hearing loss were fitted with both an ITE and a BTE hearing aid with similar electroacoustic performance. Both hearing aids were linear with output compression limiting and were fitted in a randomized order. After wearing each device for a six-week period, subj ets were asked to select the hearing aid they preferred. Variables significantly related to hearing aid choice, use and perceived benefit included ease of management, accuracy with which the NAL-R insertion gain target was achieved, earmould comfort and the type of hearing aid the client preferred initially.

Study of space shuttle EVA/IVA support requirements. Volume 4: Requirements study for space shuttle mobility aids

NASA Technical Reports Server (NTRS)

Wood, P. W., Jr.

1973-01-01

The requirements for mobility aids and restraint devices for use by personnel of the space shuttle were investigated. The devices considered were as follows: (1) translational devices to assist crewmen in moving from place to place and in moving equipment, (2) restraint devices for crewman at the worksite to prevent undesired induced motion between the crewman and the worksite, and (3) other necessary worksite provisions. Existing devices in each category are reviewed and new concepts are generated as required. Diagrams and line drawings of items of equipment are provided.

Objective and perceptual comparisons of two bluetooth hearing aid assistive devices.

PubMed

Clark, Jackie L; Pustejovsky, Carmen; Vanneste, Sven

2017-08-01

With the advent of Bluetooth technology, many of the assistive listening devices for hearing have become manufacturer specific, with little objective information about the performance provided. Thirty native English-speaking adults (mean age 29.8) with normal hearing were tested pseudo-randomly with two major hearing aid manufacturers' proprietary Bluetooth connectivity devices paired to the accompanying manufacturer's specific hearing aids. Sentence recognition performance was objectively measured for each system with signals transmitted via a land-line to the same iPhone in two conditions. There was a significant effect of participant's performance according to listening condition. There was no significant effect between device manufacturers according to listening condition, but there was a significant effect in participant's perception of "quality of sound". Despite differences in signal transmission for each devise, when worn by participants both the systems performed equally. In fact, participants expressed personal preferences for specific technology that was largely due to their perceived quality of sound while listening to recorded signals. While further research is necessary to investigate other measures of benefit for Bluetooth connectivity devices, preliminary data suggest that in order to ensure comfort and compatibility, not only should objective measures of the patient benefit be completed, but also assessing the patient's perception of benefit is equally important. Implications for Rehabilitation All professionals who work with individuals with hearing loss, become aware of the differences in the multiple choices for assistive technology readily available for hearing loss. With the ever growing dispensing of Bluetooth connectivity devices coupled to hearing aids, there is an increased burden to determine whether performance differences could exist between manufacturers. There is a growing need to investigate other measures of benefit for Bluetooth hearing aid connectivity devices that not only include objective measures, but also patient perception of benefit.

Technology for Work, Home, and Leisure. Tech Use Guide: Using Computer Technology.

ERIC Educational Resources Information Center

Williams, John M.

This guide provides a brief introduction to several types of technological devices useful to individuals with disabilities and illustrates how some individuals are applying technology in the workplace and at home. Devices described include communication aids, low-vision products, voice-activated systems, environmental controls, and aids for…

47 CFR 68.112 - Hearing aid-compatibility.

Code of Federal Regulations, 2014 CFR

2014-10-01

... located on public property or in a semi-public location (e.g., drugstore, gas station, private club). (b... disabilities. (4) All credit card operated telephones, whether located on public property or in a semipublic location (e.g., drugstore, gas station, private club), unless a hearing aid compatible (as defined in § 68...

47 CFR 68.112 - Hearing aid-compatibility.

Code of Federal Regulations, 2013 CFR

2013-10-01

... located on public property or in a semi-public location (e.g., drugstore, gas station, private club). (b... disabilities. (4) All credit card operated telephones, whether located on public property or in a semipublic location (e.g., drugstore, gas station, private club), unless a hearing aid compatible (as defined in § 68...

47 CFR 68.112 - Hearing aid-compatibility.

Code of Federal Regulations, 2012 CFR

2012-10-01

... located on public property or in a semi-public location (e.g., drugstore, gas station, private club). (b... disabilities. (4) All credit card operated telephones, whether located on public property or in a semipublic location (e.g., drugstore, gas station, private club), unless a hearing aid compatible (as defined in § 68...

Optical Docking Aid Containing Fresnel Lenses

NASA Technical Reports Server (NTRS)

Pierce, Cole J.

1995-01-01

Proposed device provides self-contained visual cues to aid in docking. Similar to devices used to guide pilots in landing on aircraft carriers. Positions and directions of beams of light give observer visual cues of position relative to docking target point. Optical assemblies generate directed, diverging beams of light that, together, mark approach path to docking point. Conceived for use in docking spacecraft at Space Station Freedom, device adapted to numerous industrial docking and alignment applications.

Left-right and front-back spatial hearing with multiple directional microphone configurations in modern hearing aids.

PubMed

Carette, Evelyne; Van den Bogaert, Tim; Laureyns, Mark; Wouters, Jan

2014-10-01

Several studies have demonstrated negative effects of directional microphone configurations on left-right and front-back (FB) sound localization. New processing schemes, such as frequency-dependent directionality and front focus with wireless ear-to-ear communication in recent, commercial hearing aids may preserve the binaural cues necessary for left-right localization and may introduce useful spectral cues necessary for FB disambiguation. In this study, two hearing aids with different processing schemes, which were both designed to preserve the ability to localize sounds in the horizontal plane (left-right and FB), were compared. We compared horizontal (left-right and FB) sound localization performance of hearing aid users fitted with two types of behind-the-ear (BTE) devices. The first type of BTE device had four different programs that provided (1) no directionality, (2-3) symmetric frequency-dependent directionality, and (4) an asymmetric configuration. The second pair of BTE devices was evaluated in its omnidirectional setting. This setting automatically activates a soft forward-oriented directional scheme that mimics the pinna effect. Also, wireless communication between the hearing aids was present in this configuration (5). A broadband stimulus was used as a target signal. The directional hearing abilities of the listeners were also evaluated without hearing aids as a reference. A total of 12 listeners with moderate to severe hearing loss participated in this study. All were experienced hearing-aid users. As a reference, 11 listeners with normal hearing participated. The participants were positioned in a 13-speaker array (left-right, -90°/+90°) or 7-speaker array (FB, 0-180°) and were asked to report the number of the loudspeaker located the closest to where the sound was perceived. The root mean square error was calculated for the left-right experiment, and the percentage of FB errors was used as a FB performance measure. RESULTS were analyzed with repeated-measures analysis of variance. For the left-right localization task, no significant differences could be proven between the unaided condition and both partial directional schemes and the omnidirectional scheme. The soft forward-oriented system and the asymmetric system did show a detrimental effect compared with the unaided condition. On average, localization was worst when users used the asymmetric condition. Analysis of the results of the FB experiment showed good performance, similar to unaided, with both the partial directional systems and the asymmetric configuration. Significantly worse performance was found with the omnidirectional and the omnidirectional soft forward-oriented BTE systems compared with the other hearing-aid systems. Bilaterally fitted partial directional systems preserve (part of) the binaural cues necessary for left-right localization and introduce, preserve, or enhance useful spectral cues that allow FB disambiguation. Omnidirectional systems, although good for left-right localization, do not provide the user with enough spectral information for an optimal FB localization performance. American Academy of Audiology.

Unmanned aerial vehicles (drones) to prevent drowning.

PubMed

Seguin, Celia; Blaquière, Gilles; Loundou, Anderson; Michelet, Pierre; Markarian, Thibaut

2018-06-01

Drowning literature have highlighted the submersion time as the most powerful predictor in assessing the prognosis. Reducing the time taken to provide a flotation device and prevent submersion appears of paramount importance. Unmanned aerial vehicles (UAVs) can provide the location of the swimmer and a flotation device. The objective of this simulation study was to evaluate the efficiency of a UAV in providing a flotation device in different sea conditions, and to compare the times taken by rescue operations with and without a UAV (standard vs UAV intervention). Several comparisons were made using professional lifeguards acting as simulated victims. A specifically-shaped UAV was used to allow us to drop an inflatable life buoy into the water. During the summer of 2017, 28 tests were performed. UAV use was associated with a reduction of time it took to provide a flotation device to the simulated victim compared with standard rescue operations (p < 0.001 for all measurements) and the time was reduced even further in moderate (81 ± 39 vs 179 ± 78 s; p < 0.001) and rough sea conditions (99 ± 34 vs 198 ± 130 s; p < 0.001). The times taken for UAV to locate the simulated victim, identify them and drop the life buoy were not altered by the weather conditions. UAV can deliver a flotation device to a swimmer safely and quickly. The addition of a UAV in rescue operations could improve the quality and speed of first aid while keeping lifeguards away from dangerous sea conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

Modeling of Women's 100-m Dash World Record: Wind-Aided or Not?

NASA Astrophysics Data System (ADS)

Hazelrigg, Conner; Waibel, Bryson; Baker, Blane

2015-11-01

On July 16, 1988, Florence Griffith Joyner (FGJ) shattered the women's 100-m dash world record (WR) with a time of 10.49 s, breaking the previous mark by an astonishing 0.27 s. By all accounts FGJ dominated the race that day, securing her place as the premiere female sprinter of that era, and possibly all time. In the aftermath of such an extraordinary performance, track officials immediately assumed that her posted time was wind aided—that is, attained under tailwind conditions beyond the legal limit of 2.0 m/s for world records. However, wind-measuring devices at the track site showed zero wind conditions during her WR performance. Before and during FGJ's race, other wind-measuring devices indicated speeds exceeding 4.0 m/s at the site of the triple jump runway, located on the same field as the running track. Video clips of flags placed near the starting line of FGJ's race also revealed tailwind conditions. Using available data from that era, the study here incorporates modeling techniques to compute velocity and position as functions of time for no wind and tailwind conditions. Modeling under no wind conditions produces a 100-m time of 10.70 s, a performance clearly attainable by FGJ during this stage of her sprinting career. Incorporating tailwinds of 4.0 m/s into the computations reduces this time by approximately 0.20 s, in close agreement with FGJ's record-breaking performance. These results strongly suggest that tailwinds of order 4 m/s were present during FGJ's world record race even though wind-measuring devices at the track site did not register these speeds. In spite of such strong evidence to support a wind-aided race on July 16, 1988, FGJ remains one of the top female sprinters in history and would likely hold the WR even today, given that she attained a non-wind-aided 100-m time of 10.61 s on the day following her WR performance.

34 CFR 300.113 - Routine checking of hearing aids and external components of surgically implanted medical devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

..., DEPARTMENT OF EDUCATION ASSISTANCE TO STATES FOR THE EDUCATION OF CHILDREN WITH DISABILITIES State... 34 Education 2 2010-07-01 2010-07-01 false Routine checking of hearing aids and external components of surgically implanted medical devices. 300.113 Section 300.113 Education Regulations of the...

Travel in Adverse Weather Using Electronic Mobility Guidance Devices

ERIC Educational Resources Information Center

Farmer, Leicester W.

1975-01-01

After a discussion of the required characteristics of an ideal aid for blind individuals traveling in adverse weather, four electronic mobility guidance devices- the Mowat Sonar Sensor, the Russell E Model Pathsounder, the Bionic C-5 Laser Cane, and the Mark II Binaural Sensory Aid-are described in detail. (Author/SB)

An Adaptive Approach to Teaching the Use of the Sonicguide with Modifications for Orthopedic Involvement.

ERIC Educational Resources Information Center

Kitzhoffer, Gerald J.

1983-01-01

Use of the Sonicguide, a binaural sensory aid, by a quadraplegic, totally blind 18-year-old student is described. The rationale for training, device adaptations, and the eventual use of the device as a primary mobility aid in areas familiar to the student are explained. (Author/MC)

Educational Aids for Visually Handicapped.

ERIC Educational Resources Information Center

American Printing House for the Blind, Louisville, KY.

Listings specifying source and cost are provided of tactile aids and materials designed for the visually handicapped. Items are presented in the following categories: supply sources and catalogs for aids; braille devices, including duplicators, reading and writing aids, reading readiness materials, and writing machines, slates, and styluses; deaf…

Reading aids for adults with low vision.

PubMed

Virgili, Gianni; Acosta, Ruthy; Bentley, Sharon A; Giacomelli, Giovanni; Allcock, Claire; Evans, Jennifer R

2018-04-17

The purpose of low-vision rehabilitation is to allow people to resume or to continue to perform daily living tasks, with reading being one of the most important. This is achieved by providing appropriate optical devices and special training in the use of residual-vision and low-vision aids, which range from simple optical magnifiers to high-magnification video magnifiers. To assess the effects of different visual reading aids for adults with low vision. We searched the Cochrane Central Register of Controlled Trials (CENTRAL) (which contains the Cochrane Eyes and Vision Trials Register) (2017, Issue 12); MEDLINE Ovid; Embase Ovid; BIREME LILACS, OpenGrey, the ISRCTN registry; ClinicalTrials.gov and the World Health Organization (WHO) International Clinical Trials Registry Platform (ICTRP). The date of the search was 17 January 2018. This review includes randomised and quasi-randomised trials that compared any device or aid used for reading to another device or aid in people aged 16 or over with low vision as defined by the study investigators. We did not compare low-vision aids with no low-vision aid since it is obviously not possible to measure reading speed, our primary outcome, in people that cannot read ordinary print. We considered reading aids that maximise the person's visual reading capacity, for example by increasing image magnification (optical and electronic magnifiers), augmenting text contrast (coloured filters) or trying to optimise the viewing angle or gaze position (such as prisms). We have not included studies investigating reading aids that allow reading through hearing, such as talking books or screen readers, or through touch, such as Braille-based devices and we did not consider rehabilitation strategies or complex low-vision interventions. We used standard methods expected by Cochrane. At least two authors independently assessed trial quality and extracted data. The primary outcome of the review was reading speed in words per minute. Secondary outcomes included reading duration and acuity, ease and frequency of use, quality of life and adverse outcomes. We graded the certainty of the evidence using GRADE. We included 11 small studies with a cross-over design (435 people overall), one study with two parallel arms (37 participants) and one study with three parallel arms (243 participants). These studies took place in the USA (7 studies), the UK (5 studies) and Canada (1 study). Age-related macular degeneration (AMD) was the most frequent cause of low vision, with 10 studies reporting 50% or more participants with the condition. Participants were aged 9 to 97 years in these studies, but most were older (the median average age across studies was 71 years). None of the studies were masked; otherwise we largely judged the studies to be at low risk of bias. All studies reported the primary outcome: results for reading speed. None of the studies measured or reported adverse outcomes.Reading speed may be higher with stand-mounted closed circuit television (CCTV) than with optical devices (stand or hand magnifiers) (low-certainty evidence, 2 studies, 92 participants). There was moderate-certainty evidence that reading duration was longer with the electronic devices and that they were easier to use. Similar results were seen for electronic devices with the camera mounted in a 'mouse'. Mixed results were seen for head-mounted devices with one study of 70 participants finding a mouse-based head-mounted device to be better than an optical device and another study of 20 participants finding optical devices better (low-certainty evidence). Low-certainty evidence from three studies (93 participants) suggested no important differences in reading speed, acuity or ease of use between stand-mounted and head-mounted electronic devices. Similarly, low-certainty evidence from one study of 100 participants suggested no important differences between a 9.7'' tablet computer and stand-mounted CCTV in reading speed, with imprecise estimates (other outcomes not reported).Low-certainty evidence showed little difference in reading speed in one study with 100 participants that added electronic portable devices to preferred optical devices. One parallel-arm study in 37 participants found low-certainty evidence of higher reading speed at one month if participants received a CCTV at the initial rehabilitation consultation instead of a standard low-vision aids prescription alone.A parallel-arm study including 243 participants with AMD found no important differences in reading speed, reading acuity and quality of life between prism spectacles and conventional spectacles. One study in 10 people with AMD found that reading speed with several overlay coloured filters was no better and possibly worse than with a clear filter (low-certainty evidence, other outcomes not reported). There is insufficient evidence supporting the use of a specific type of electronic or optical device for the most common profiles of low-vision aid users. However, there is some evidence that stand-mounted electronic devices may improve reading speeds compared with optical devices. There is less evidence to support the use of head-mounted or portable electronic devices; however, the technology of electronic devices may have improved since the studies included in this review took place, and modern portable electronic devices have desirable properties such as flexible use of magnification. There is no good evidence to support the use of filters or prism spectacles. Future research should focus on assessing sustained long-term use of each device and the effect of different training programmes on its use, combined with investigation of which patient characteristics predict performance with different devices, including some of the more costly electronic devices.

Effectiveness of alternative listening devices to conventional hearing aids for adults with hearing loss: a systematic review protocol.

PubMed

Maidment, David W; Barker, Alex B; Xia, Jun; Ferguson, Melanie A

2016-10-27

Hearing loss is a major public health concern, affecting over 11 million people in the UK. While hearing aids are the most common clinical intervention for hearing loss, the majority of people that would benefit from using hearing aids do not take them up. Recent technological advances have led to a rapid increase of alternative listening devices to conventional hearing aids. These include hearing aids that can be customised using a smartphone, smartphone-based 'hearing aid' apps, personal sound amplification products and wireless hearing products. However, no systematic review has been published evaluating whether alternative listening devices are an effective management strategy for people with hearing loss. The objective of this systematic review is to assess whether alternative listening devices are an effective intervention for adults with hearing loss. Methods are reported according to the Preferred Reporting Items for Systematic reviews and Meta-analyses Protocols (PRISMA-P) 2015 checklist. Retrospective or prospective studies, randomised controlled trials, non-randomised controlled trials, and before-after comparison studies will be eligible for inclusion. We will include studies with adult participants (≥18 years) with a mild or moderate hearing loss. The intervention should be an alternative listening device to a conventional hearing aid (comparison). Studies will be restricted to outcomes associated with the consequences of hearing loss. We will search relevant databases to identify published, completed but unpublished and ongoing trials. The overall quality of included evidence will be evaluated using the GRADE system, and meta-analysis performed if appropriate. No ethical issues are foreseen. The findings will be reported at national and international conferences, primarily audiology, and ear, nose and throat, and in a peer-reviewed journal using the PRISMA guidelines. PROSPERO CRD4201502958. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Using old technology to implement modern computer-aided decision support for primary diabetes care.

PubMed Central

Hunt, D. L.; Haynes, R. B.; Morgan, D.

2001-01-01

BACKGROUND: Implementation rates of interventions known to be beneficial for people with diabetes mellitus are often suboptimal. Computer-aided decision support systems (CDSSs) can improve these rates. The complexity of establishing a fully integrated electronic medical record that provides decision support, however, often prevents their use. OBJECTIVE: To develop a CDSS for diabetes care that can be easily introduced into primary care settings and diabetes clinics. THE SYSTEM: The CDSS uses fax-machine-based optical character recognition software for acquiring patient information. Simple, 1-page paper forms, completed by patients or health practitioners, are faxed to a central location. The information is interpreted and recorded in a database. This initiates a routine that matches the information against a knowledge base so that patient-specific recommendations can be generated. These are formatted and faxed back within 4-5 minutes. IMPLEMENTATION: The system is being introduced into 2 diabetes clinics. We are collecting information on frequency of use of the system, as well as satisfaction with the information provided. CONCLUSION: Computer-aided decision support can be provided in any setting with a fax machine, without the need for integrated electronic medical records or computerized data-collection devices. PMID:11825194

Using old technology to implement modern computer-aided decision support for primary diabetes care.

PubMed

Hunt, D L; Haynes, R B; Morgan, D

2001-01-01

Implementation rates of interventions known to be beneficial for people with diabetes mellitus are often suboptimal. Computer-aided decision support systems (CDSSs) can improve these rates. The complexity of establishing a fully integrated electronic medical record that provides decision support, however, often prevents their use. To develop a CDSS for diabetes care that can be easily introduced into primary care settings and diabetes clinics. THE SYSTEM: The CDSS uses fax-machine-based optical character recognition software for acquiring patient information. Simple, 1-page paper forms, completed by patients or health practitioners, are faxed to a central location. The information is interpreted and recorded in a database. This initiates a routine that matches the information against a knowledge base so that patient-specific recommendations can be generated. These are formatted and faxed back within 4-5 minutes. The system is being introduced into 2 diabetes clinics. We are collecting information on frequency of use of the system, as well as satisfaction with the information provided. Computer-aided decision support can be provided in any setting with a fax machine, without the need for integrated electronic medical records or computerized data-collection devices.

21 CFR 864.5260 - Automated cell-locating device.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Automated cell-locating device. 864.5260 Section... § 864.5260 Automated cell-locating device. (a) Identification. An automated cell-locating device is a device used to locate blood cells on a peripheral blood smear, allowing the operator to identify and...

21 CFR 864.5260 - Automated cell-locating device.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Automated cell-locating device. 864.5260 Section... § 864.5260 Automated cell-locating device. (a) Identification. An automated cell-locating device is a device used to locate blood cells on a peripheral blood smear, allowing the operator to identify and...

21 CFR 864.5260 - Automated cell-locating device.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Automated cell-locating device. 864.5260 Section... § 864.5260 Automated cell-locating device. (a) Identification. An automated cell-locating device is a device used to locate blood cells on a peripheral blood smear, allowing the operator to identify and...

21 CFR 864.5260 - Automated cell-locating device.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Automated cell-locating device. 864.5260 Section... § 864.5260 Automated cell-locating device. (a) Identification. An automated cell-locating device is a device used to locate blood cells on a peripheral blood smear, allowing the operator to identify and...

21 CFR 864.5260 - Automated cell-locating device.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Automated cell-locating device. 864.5260 Section... § 864.5260 Automated cell-locating device. (a) Identification. An automated cell-locating device is a device used to locate blood cells on a peripheral blood smear, allowing the operator to identify and...

25 CFR 502.7 - Electronic, computer or other technologic aid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... other technologic aid means any machine or device that: (1) Assists a player or the playing of a game... not limited to, machines or devices that: (1) Broaden the participation levels in a common game; (2) Facilitate communication between and among gaming sites; or (3) Allow a player to play a game with or against...

25 CFR 502.7 - Electronic, computer or other technologic aid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... other technologic aid means any machine or device that: (1) Assists a player or the playing of a game... not limited to, machines or devices that: (1) Broaden the participation levels in a common game; (2) Facilitate communication between and among gaming sites; or (3) Allow a player to play a game with or against...

25 CFR 502.7 - Electronic, computer or other technologic aid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... other technologic aid means any machine or device that: (1) Assists a player or the playing of a game... not limited to, machines or devices that: (1) Broaden the participation levels in a common game; (2) Facilitate communication between and among gaming sites; or (3) Allow a player to play a game with or against...

25 CFR 502.7 - Electronic, computer or other technologic aid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... other technologic aid means any machine or device that: (1) Assists a player or the playing of a game... not limited to, machines or devices that: (1) Broaden the participation levels in a common game; (2) Facilitate communication between and among gaming sites; or (3) Allow a player to play a game with or against...

25 CFR 502.7 - Electronic, computer or other technologic aid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... other technologic aid means any machine or device that: (1) Assists a player or the playing of a game... not limited to, machines or devices that: (1) Broaden the participation levels in a common game; (2) Facilitate communication between and among gaming sites; or (3) Allow a player to play a game with or against...

Facilitating Integration of Electron Beam Lithography Devices with Interactive Videodisc, Computer-Based Simulation and Job Aids.

ERIC Educational Resources Information Center

Von Der Linn, Robert Christopher

A needs assessment of the Grumman E-Beam Systems Group identified the requirement for additional skill mastery for the engineers who assemble, integrate, and maintain devices used to manufacture integrated circuits. Further analysis of the tasks involved led to the decision to develop interactive videodisc, computer-based job aids to enable…

34 CFR 300.113 - Routine checking of hearing aids and external components of surgically implanted medical devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

..., DEPARTMENT OF EDUCATION ASSISTANCE TO STATES FOR THE EDUCATION OF CHILDREN WITH DISABILITIES State... 34 Education 2 2011-07-01 2010-07-01 true Routine checking of hearing aids and external components of surgically implanted medical devices. 300.113 Section 300.113 Education Regulations of the Offices...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 29 Labor 8 2013-07-01 2013-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 29 Labor 8 2012-07-01 2012-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

29 CFR 1926.1416 - Operational aids.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 29 Labor 8 2014-07-01 2014-07-01 false Operational aids. 1926.1416 Section 1926.1416 Labor... Operational aids. (a) The devices listed in this section (“listed operational aids”) are required on all... November 8, 2011. (b) Operations must not begin unless the listed operational aids are in proper working...

VISUAL AIDS HANDBOOK FOR FOREIGN LANGUAGE TEACHERS.

ERIC Educational Resources Information Center

GARIBALDI, VIRGINIA; STRASHEIM, LORRAINE A.

TEACHERS ARE SHOWN HOW TO CONSTRUCT AND USE THEIR OWN VISUAL AIDS FOR ILLUSTRATING USEFUL BUT DIFFICULT EXPRESSIONS COMMON TO ALL LANGUAGES. SUCH SPECIFIC AIDS AS PROPS, REALIA, FLASHCARDS, CHARTS, FLANNEL AND MAGNETIC BOARDS, POCKET CHARTS, PUPPETS, DRILL CUING DEVICES, AND CULTURALLY ORIENTED VISUAL AIDS ARE DESCRIBED. LISTS OF PROFESSIONAL…

Hearing Aid Tester

NASA Technical Reports Server (NTRS)

1978-01-01

Hearing aids often develop malfunctions that are not detected by the wearer. This is particularly true when the wearers are school-age children. Studies of selected groups showed that from 30 to more than 50 percent of school children were not getting adequate benefit from their hearing aids because of unrecognized malfunctions, usually low or dead batteries. This can be serious because hearing impairment retards a child's educational progress. NASA technology incorporated in the Hearing Aid Malfunction Detection Unit (HAMDU), the device pictured, is expected to provide an effective countermeasure to the childrens' hearing aid problem. A patent license has been awarded to a minority-owned firm, Hopkins International Company, a subsidiary of H. H. Aerospace Design Co., Inc., Elmford, New York. The company plans early commercial availability of its version of the device.

Pinnaplasty: reshaping ears to improve hearing aid retention.

PubMed

Gault, David; Grob, Marion; Odili, Joy

2007-01-01

The hearing aid is extremely important to the deaf. A small number have difficulty in retaining the device because the ear is prominent or cup-shaped. This report describes 11 children whose ear shape was modified to improve hearing aid retention and one adult in whom an over set back ear was released to allow fitment of a postaural device. In eight of the 11 children treated, conservative measures such as double-sided tape and retention bands (Huggies) had been tried previously without success. The creation of an antihelical fold in a misshapen ear lacking such a fold provides a reinforcing strut which is useful to support a hearing aid. In patients whose ear had been excessively tethered by previous surgery, projection was restored by inserting a cartilage block behind the ear. In one child with ears tethered by previous surgery, costal cartilage was used not only to release both ears, but also to reconstruct a new helical rim on one side. Surgery enabled a normal postaural hearing aid to be worn in 17 of the 19 ears treated. The two failures deserve special mention. In one patient with a unilateral deformity and severe mental retardation, the dressings were pulled off immediately after surgery. In another patient with a bilateral problem, the appearance and hearing aid retention was improved, but there was not enough room in the postauricular sulcus on one side for the battery component to fit comfortably and an in-the-ear device is now used on that side. Pinnaplasty is a helpful strategy to improve hearing aid retention. Care must be taken not to overdo the set back so that enough room is left to retain the hearing device.

Self-Assessment of Hearing and Purchase of Hearing Aids by Middle-Aged and Elderly Adults

PubMed Central

Otavio, Andressa Colares da Costa; Coradini, Patricia Pérez; Teixeira, Adriane Ribeiro

2015-01-01

Introduction Presbycusis is a consequence of aging. Prescription of hearing aids is part of the treatment, although the prevalence of use by elderly people is still small. Objective To verify whether or not self-assessment of hearing is a predictor for purchase of hearing aids. Methods Quantitative, cross-sectional, descriptive, and observational study. Participants were subjects who sought a private hearing center for selection of hearing aids. During the diagnostic interview, subjects answered the following question: “On a scale of 1 to 10, with 1 being the worst and 10 the best, how would you rate your overall hearing ability?” After that, subjects underwent audiometry, selected a hearing aid, performed a home trial, and decided whether or not to purchase the hearing aid. The variables were associated and analyzed statistically. Results The sample was comprised of 32 subjects, both men and women, with a higher number of women. Mean age was 71.41 ± 12.14 years. Self-assessment of hearing ranged from 2 to 9 points. Overall, 71.9% of the subjects purchased hearing aids. There was no association between scores in the self-assessment and the purchase of hearing aids (p = 0.263). Among those who scored between 2 and 5 points, 64.7% purchased the device; between 6 and 7 points, 76.09% purchased the device; and between 8 and 9 points, 50% purchased the device, respectively. Conclusion There is evidence that low self-assessment scores lead to the purchase of hearing aids, although no significant association was observed in the sample. PMID:26722346

A Compact and Low-Cost MEMS Loudspeaker for Digital Hearing Aids.

PubMed

Sang-Soo Je; Rivas, F; Diaz, R E; Jiuk Kwon; Jeonghwan Kim; Bakkaloglu, B; Kiaei, S; Junseok Chae

2009-10-01

A microelectromechanical-systems (MEMS)-based electromagnetically actuated loudspeaker to reduce form factor, cost, and power consumption, and increase energy efficiency in hearing-aid applications is presented. The MEMS loudspeaker has multilayer copper coils, an NiFe soft magnet on a thin polyimide diaphragm, and an NdFeB permanent magnet on the perimeter. The coil impedance is measured at 1.5 Omega, and the resonant frequency of the diaphragm is located far from the audio frequency range. The device is driven by a power-scalable, 0.25-mum complementary metal-oxide semiconductor class-D SigmaDelta amplifier stage. The class-D amplifier is formed by a differential H-bridge driven by a single bit, pulse-density-modulated SigmaDelta bitstream at a 1.2-MHz clock rate. The fabricated MEMS loudspeaker generates more than 0.8-mum displacement, equivalent to 106-dB sound pressure level (SPL), with 0.13-mW power consumption. Driven by the SigmaDelta class-D amplifier, the MEMS loudspeaker achieves measured 65-dB total harmonic distortion (THD) with a measurement uncertainty of less than 10%. Energy-efficient and cost-effective advanced hearing aids would benefit from further miniaturization via MEMS technology. The results from this study appear very promising for developing a compact, mass-producible, low-power loudspeaker with sufficient sound generation for hearing-aid applications.

Design and Evaluation of a Protocol to Assess Electronic Travel Aids for Persons Who Are Visually Impaired

ERIC Educational Resources Information Center

Havik, Else M.; Steyvers, Frank J. J. M.; van der Velde, Hanneke; Pinkster, J. Christiaan; Kooijman, Aart C.

2010-01-01

This study evaluated a protocol that was developed to assess how beneficial electronic travel aids are for persons who are visually impaired. Twenty persons with visual impairments used an electronic travel device (Trekker) for six weeks to conform to the protocol, which proved useful in identifying successful users of the device. (Contains 2…

21 CFR 886.4400 - Electronic metal locator.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Electronic metal locator. 886.4400 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4400 Electronic metal locator. (a) Identification. An electronic metal locator is an AC-powered device with probes intended to locate metallic...

21 CFR 886.4400 - Electronic metal locator.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Electronic metal locator. 886.4400 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4400 Electronic metal locator. (a) Identification. An electronic metal locator is an AC-powered device with probes intended to locate metallic...

21 CFR 886.4400 - Electronic metal locator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Electronic metal locator. 886.4400 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4400 Electronic metal locator. (a) Identification. An electronic metal locator is an AC-powered device with probes intended to locate metallic...

21 CFR 886.4400 - Electronic metal locator.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Electronic metal locator. 886.4400 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4400 Electronic metal locator. (a) Identification. An electronic metal locator is an AC-powered device with probes intended to locate metallic...

21 CFR 886.4400 - Electronic metal locator.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Electronic metal locator. 886.4400 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4400 Electronic metal locator. (a) Identification. An electronic metal locator is an AC-powered device with probes intended to locate metallic...

An experimental study addressing the use of geoforensic analysis for the exploitation of improvised explosive devices (IEDs).

PubMed

Wilks, Beth; Morgan, Ruth M; Rose, Neil L

2017-09-01

The use of geoforensic analysis in criminal investigations is continuing to develop, with the diversification of analytical techniques, many of which are semi-automated, facilitating prompt analysis of large sample sets at a relatively low cost. Whilst micro-scale geoforensic analysis has been shown to assist criminal investigations including homicide (Concheri et al., 2011 [1]), wildlife crime (Morgan et al., 2006 [2]), illicit drug distribution (Stanley, 1992 [3]), and burglary (Mildenhall, 2006 [4]), its application to the pressing international security threat posed by Improvised Explosive Devices (IEDs) is yet to be considered. This experimental study simulated an IED supply chain from the sourcing of raw materials through to device emplacement. Mineralogy, quartz grain surface texture analysis (QGSTA) and particle size analysis (PSA) were used to assess whether environmental materials were transferred and subsequently persisted on the different components of three pressure plate IEDs. The research also addressed whether these samples were comprised of material from single or multiple geographical provenances that represented supply chain activity nodes. The simulation demonstrated that material derived from multiple activity nodes, was transferred and persisted on device components. The results from the mineralogy and QGSTA illustrated the value these techniques offer for the analysis of mixed provenance samples. The results from the PSA, which produces a bulk signature of the sample, failed to distinguish multiple provenances. The study also considered how the environmental material recovered could be used to generate information regarding the geographical locations the device had been in contact with, in an intelligence style investigation, and demonstrated that geoforensic analysis has the potential to be of value to international counter-IED efforts. It is a tool that may be used to prevent the distribution of large quantities of devices, by aiding the identification of the geographical location of key activity nodes. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Clearing the air: protocol for a systematic meta-narrative review on the harms and benefits of e-cigarettes and vapour devices.

PubMed

MacDonald, Marjorie; O'Leary, Renee; Stockwell, Tim; Reist, Dan

2016-05-21

Under the shadow of the tobacco epidemic, the sale and use of e-cigarettes and other vapour devices is increasing dramatically. A contentious debate has risen within public health over the harms and benefits of these devices. Clearing the Air seeks to clarify the issues with a systematic review that informs the pressing regulatory and public health decisions to be made regarding these new products. Using an integrated knowledge translation approach, public health researchers and knowledge users will work collaboratively throughout the project. Our research questions are the following: (1) What are the health risks and benefits of vapour devices, and how do these compare to cigarettes? (2) What is the harm reduction potential of vapour devices for individuals, the environment, and society? (3) Does youth vapour device experimentation lead to cigarette use? (4) Can vapour devices be effective aids for tobacco cessation? and (5) What is the potential toxicity of second-hand vapour? We are using meta-narrative review to synthesize studies from diverse research traditions because of its capacity to address contestations around a topic. The project has six phases. In the planning phase, we finalized the research questions. In the search phase, we are locating academic publications and grey literature aided by a research librarian. The mapping phase involves categorizing these papers into research traditions to understand different perspectives on the evidence for each research question. In the appraisal phase, we will select and evaluate the relevant papers. Finally, in the synthesis phase, using analytic techniques unique to meta-narrative methodology, we will compare and contrast the evidence from different research traditions to answer our research questions, identifying overarching meta-narratives. In the final stage, the full team will draft recommendations to be disseminated through a variety of knowledge translation strategies. Meta-narrative synthesis has the unique capacity to expose the debates that are influencing the interpretation of empirical studies on vapour devices. We seek to "clear the air" with an even-handed review of the evidence and an understanding of the tensions within public health so that we can offer clear-headed recommendations for policy, regulation, and future research. PROSPERO CRD42015025267.

A Device for Human Ultrasonic Echolocation.

PubMed

Sohl-Dickstein, Jascha; Teng, Santani; Gaub, Benjamin M; Rodgers, Chris C; Li, Crystal; DeWeese, Michael R; Harper, Nicol S

2015-06-01

We present a device that combines principles of ultrasonic echolocation and spatial hearing to provide human users with environmental cues that are 1) not otherwise available to the human auditory system, and 2) richer in object and spatial information than the more heavily processed sonar cues of other assistive devices. The device consists of a wearable headset with an ultrasonic emitter and stereo microphones with affixed artificial pinnae. The goal of this study is to describe the device and evaluate the utility of the echoic information it provides. The echoes of ultrasonic pulses were recorded and time stretched to lower their frequencies into the human auditory range, then played back to the user. We tested performance among naive and experienced sighted volunteers using a set of localization experiments, in which the locations of echo-reflective surfaces were judged using these time-stretched echoes. Naive subjects were able to make laterality and distance judgments, suggesting that the echoes provide innately useful information without prior training. Naive subjects were generally unable to make elevation judgments from recorded echoes. However, trained subjects demonstrated an ability to judge elevation as well. This suggests that the device can be used effectively to examine the environment and that the human auditory system can rapidly adapt to these artificial echolocation cues. Interpreting and interacting with the external world constitutes a major challenge for persons who are blind or visually impaired. This device has the potential to aid blind people in interacting with their environment.

A device for human ultrasonic echolocation

PubMed Central

Gaub, Benjamin M.; Rodgers, Chris C.; Li, Crystal; DeWeese, Michael R.; Harper, Nicol S.

2015-01-01

Objective We present a device that combines principles of ultrasonic echolocation and spatial hearing to provide human users with environmental cues that are 1) not otherwise available to the human auditory system and 2) richer in object, and spatial information than the more heavily processed sonar cues of other assistive devices. The device consists of a wearable headset with an ultrasonic emitter and stereo microphones with affixed artificial pinnae. The goal of this study is to describe the device and evaluate the utility of the echoic information it provides. Methods The echoes of ultrasonic pulses were recorded and time-stretched to lower their frequencies into the human auditory range, then played back to the user. We tested performance among naive and experienced sighted volunteers using a set of localization experiments in which the locations of echo-reflective surfaces were judged using these time stretched echoes. Results Naive subjects were able to make laterality and distance judgments, suggesting that the echoes provide innately useful information without prior training. Naive subjects were generally unable to make elevation judgments from recorded echoes. However trained subjects demonstrated an ability to judge elevation as well. Conclusion This suggests that the device can be used effectively to examine the environment and that the human auditory system can rapidly adapt to these artificial echolocation cues. Significance Interpreting and interacting with the external world constitutes a major challenge for persons who are blind or visually impaired. This device has the potential to aid blind people in interacting with their environment. PMID:25608301

Evaluation of location and number of aid post for sustainable humanitarian relief using agent based modeling (ABM) and geographic information system (GIS)

NASA Astrophysics Data System (ADS)

Khair, Fauzi; Sopha, Bertha Maya

2017-12-01

One of the crucial phases in disaster management is the response phase or the emergency response phase. It requires a sustainable system and a well-integrated management system. Any errors in the system on this phase will impact on significant increase of the victims number as well as material damage caused. Policies related to the location of aid posts are important decisions. The facts show that there are many failures in the process of providing assistance to the refugees due to lack of preparation and determination of facilities and aid post location. Therefore, this study aims to evaluate the number and location of aid posts on Merapi eruption in 2010. This study uses an integration between Agent Based Modeling (ABM) and Geographic Information System (GIS) about evaluation of the number and location of the aid post using some scenarios. The ABM approach aims to describe the agents behaviour (refugees and volunteers) in the event of a disaster with their respective characteristics. While the spatial data, GIS useful to describe real condition of the Sleman regency road. Based on the simulation result, it shows alternative scenarios that combine DERU UGM post, Maguwoharjo Stadium, Tagana Post and Pakem Main Post has better result in handling and distributing aid to evacuation barrack compared to initial scenario. Alternative scenarios indicates the unmet demands are less than the initial scenario.

Low cost training aids and devices

NASA Technical Reports Server (NTRS)

Lawver, J.; Lee, A.

1984-01-01

The need for advanced flight simulators for two engine aircraft is discussed. Cost effectiveness is a major requirement. Other training aids available for increased effectiveness are recommended. Training aids include: (1) audio-visual slides; (2) information transfer; (3) programmed instruction; and (4) interactive training systems.

Hearing Aid Fitting in Infants.

ERIC Educational Resources Information Center

Hoover, Brenda M.

2000-01-01

This article examines the latest technological advances in hearing aids and explores the available research to help families and professionals make informed decisions when fitting amplification devices on infants and young children. Diagnostic procedures, evaluation techniques, hearing aid selection, circuit and advanced technology options, and…

GT3X+ accelerometer, Yamax pedometer and SC-StepMX pedometer step count accuracy in community-dwelling older adults.

PubMed

Webber, Sandra C; Magill, Sheila M; Schafer, Jenessa L; Wilson, Kaylie C S

2014-07-01

The purpose was to compare step count accuracy of an accelerometer (ActiGraph GT3X+), a mechanical pedometer (Yamax SW200), and a piezoelectric pedometer (SC-StepMX). Older adults (n = 13 with walking aids, n = 22 without; M = 81.5 years old, SD = 5.0) walked 100 m wearing the devices. Device-detected steps were compared with manually counted steps. We found no significant differences among monitors for those who walked without aids (p = .063). However, individuals who used walking aids exhibited slower gait speeds (M = 0.83 m/s, SD = 0.2) than non-walking aid users (M = 1.21 m/s, SD = 0.2, p < .001), and for them the SC-StepMX demonstrated a significantly lower percentage of error (Mdn = 1.0, interquartile range [IQR] = 0.5-2.0) than the other devices (Yamax SW200, Mdn = 68.9, IQR = 35.9-89.3; left GT3X+, Mdn = 52.0, IQR = 37.1-58.9; right GT3X+, Mdn = 51.0, IQR = 32.3-66.5; p < .05). These results support using a piezoelectric pedometer for measuring steps in older adults who use walking aids and who walk slowly.

AIDSinfo

MedlinePlus

... glossary View AIDS info infographics! Follow @AIDSinfo on Twitter! Download the AIDS info apps for your iOS and Android devices Facebook Twitter RSS Share Widgets Email Updates QUICK LINKS Home ...

Evaluation of Extended-wear Hearing Aid Technology for Operational Military Use

DTIC Science & Technology

2017-07-01

for a transparent hearing protection device that could protect the hearing of normal-hearing listeners without degrading auditory situational...method, suggest that continuous noise protection is also comparable to conventional earplug devices. Behavioral testing on listeners with normal...associated with the extended-wear hearing aid could be adapted to provide long-term hearing protection for listeners with normal hearing with minimal

Other Products and Devices to Improve Hearing

MedlinePlus

... and Consumer Devices Consumer Products Hearing Aids Other Products and Devices to Improve Hearing Share Tweet Linkedin ... no hearing in one ear. Personal Sound Amplification Products Personal Sound Amplification Products (PSAPs), or sound amplifiers, ...

77 FR 32642 - Medical Devices; Exemption From Premarket Notification: Powered Patient Transport

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-01

...] Medical Devices; Exemption From Premarket Notification: Powered Patient Transport AGENCY: Food and Drug... transport devices commonly known as stairlifts. These devices are used to assist transfers of a mobility... behalf of Bruno Independent Living Aids, Inc., for powered patient transport devices (commonly known as...

Effectiveness of alternative listening devices to conventional hearing aids for adults with hearing loss: a systematic review protocol

PubMed Central

Barker, Alex B; Xia, Jun

2016-01-01

Introduction Hearing loss is a major public health concern, affecting over 11 million people in the UK. While hearing aids are the most common clinical intervention for hearing loss, the majority of people that would benefit from using hearing aids do not take them up. Recent technological advances have led to a rapid increase of alternative listening devices to conventional hearing aids. These include hearing aids that can be customised using a smartphone, smartphone-based ‘hearing aid’ apps, personal sound amplification products and wireless hearing products. However, no systematic review has been published evaluating whether alternative listening devices are an effective management strategy for people with hearing loss. Methods and analysis The objective of this systematic review is to assess whether alternative listening devices are an effective intervention for adults with hearing loss. Methods are reported according to the Preferred Reporting Items for Systematic reviews and Meta-analyses Protocols (PRISMA-P) 2015 checklist. Retrospective or prospective studies, randomised controlled trials, non-randomised controlled trials, and before-after comparison studies will be eligible for inclusion. We will include studies with adult participants (≥18 years) with a mild or moderate hearing loss. The intervention should be an alternative listening device to a conventional hearing aid (comparison). Studies will be restricted to outcomes associated with the consequences of hearing loss. We will search relevant databases to identify published, completed but unpublished and ongoing trials. The overall quality of included evidence will be evaluated using the GRADE system, and meta-analysis performed if appropriate. Ethics and dissemination No ethical issues are foreseen. The findings will be reported at national and international conferences, primarily audiology, and ear, nose and throat, and in a peer-reviewed journal using the PRISMA guidelines. Review registration number PROSPERO CRD4201502958. PMID:27789514

Evaluating Imaging and Computer-aided Detection and Diagnosis Devices at the FDA

PubMed Central

Gallas, Brandon D.; Chan, Heang-Ping; D’Orsi, Carl J.; Dodd, Lori E.; Giger, Maryellen L.; Gur, David; Krupinski, Elizabeth A.; Metz, Charles E.; Myers, Kyle J.; Obuchowski, Nancy A.; Sahiner, Berkman; Toledano, Alicia Y.; Zuley, Margarita L.

2017-01-01

This report summarizes the Joint FDA-MIPS Workshop on Methods for the Evaluation of Imaging and Computer-Assist Devices. The purpose of the workshop was to gather information on the current state of the science and facilitate consensus development on statistical methods and study designs for the evaluation of imaging devices to support US Food and Drug Administration submissions. Additionally, participants expected to identify gaps in knowledge and unmet needs that should be addressed in future research. This summary is intended to document the topics that were discussed at the meeting and disseminate the lessons that have been learned through past studies of imaging and computer-aided detection and diagnosis device performance. PMID:22306064

21 CFR 872.1850 - Lead-lined position indicator.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Diagnostic Devices § 872.1850 Lead-lined position indicator. (a... dental x-ray tube and intended to aid in positioning the tube, to prevent the misfocusing of the x-rays...

Vision-Aided Context-Aware Framework for Personal Navigation Services

NASA Astrophysics Data System (ADS)

Saeedi, S.; Moussa, A.; El-Sheimy, N., , Dr.

2012-07-01

The ubiquity of mobile devices (such as smartphones and tablet-PCs) has encouraged the use of location-based services (LBS) that are relevant to the current location and context of a mobile user. The main challenge of LBS is to find a pervasive and accurate personal navigation system (PNS) in different situations of a mobile user. In this paper, we propose a method of personal navigation for pedestrians that allows a user to freely move in outdoor environments. This system aims at detection of the context information which is useful for improving personal navigation. The context information for a PNS consists of user activity modes (e.g. walking, stationary, driving, and etc.) and the mobile device orientation and placement with respect to the user. After detecting the context information, a low-cost integrated positioning algorithm has been employed to estimate pedestrian navigation parameters. The method is based on the integration of the relative user's motion (changes of velocity and heading angle) estimation based on the video image matching and absolute position information provided by GPS. A Kalman filter (KF) has been used to improve the navigation solution when the user is walking and the phone is in his/her hand. The Experimental results demonstrate the capabilities of this method for outdoor personal navigation systems.

Aerial view of the Shuttle Landing Facility

NASA Technical Reports Server (NTRS)

1998-01-01

From the air over KSC can be seen the Shuttle Landing Facility. Orbiter landings at the Kennedy Space Center are made on one of the largest runways in the world. The runway is located 3.2 km (2 miles) northwest of the Vehicle Assembly Building and is 4,572 meters (15,000ft) long and 91.4 meters (300ft) wide -- about as wide as the length of a football field. It has 305 meters (1000ft) of paved overruns at each end and the paving thickness is 40.6cm (15 inches) at the center. At left in the photo is the Aircraft Ground Equipment Shed; in the center is the Landing Aids Control Building (LACB) which supports landing operations and houses operations personnel. Located at the northeast corner of the parking apron is the Mate/Demate device (MDD) used to raise and lower the orbiter from its 747 carrier aircraft during ferry operations. The open-truss steel structure is equipped with hoists, adapters and movable platforms for access to certain orbiter components and equipment. It also is equipped with lightning protection devices. The MDD is 45.7 meters (150ft) long, 28.3 meters (93ft) wide and 32 meters (105ft) high. On the landing area in front of the SLF is a T-38 jet airplane.

A simple device for teaching direct ophthalmoscopy to primary care practitioners.

PubMed

Chung, Kelly D; Watzke, Robert C

2004-09-01

Ophthalmoscopy, a valuable skill for primary care practitioners, can be challenging to learn. A simple and inexpensive device for teaching direct ophthalmoscopy to primary care practitioners is described. Device description. Cylindrical plastic canisters were altered to have an artificial pupil at one end and a replaceable fundus photograph at the other end to simulate the mechanics of performing direct ophthalmoscopy on a real eye. These were tested for ease of use by primary care students. The devices to aid in teaching ophthalmoscopy proved to be simple and inexpensive to construct. They allowed students to practice direct ophthalmoscopy technique and identification of funduscopic abnormalities. This simple device for teaching direct ophthalmoscopy to primary care practitioners is inexpensive to create and is a valuable aid for teaching direct ophthalmoscopy to primary care practitioners.

Use of force feedback to enhance graphical user interfaces

NASA Astrophysics Data System (ADS)

Rosenberg, Louis B.; Brave, Scott

1996-04-01

This project focuses on the use of force feedback sensations to enhance user interaction with standard graphical user interface paradigms. While typical joystick and mouse devices are input-only, force feedback controllers allow physical sensations to be reflected to a user. Tasks that require users to position a cursor on a given target can be enhanced by applying physical forces to the user that aid in targeting. For example, an attractive force field implemented at the location of a graphical icon can greatly facilitate target acquisition and selection of the icon. It has been shown that force feedback can enhance a users ability to perform basic functions within graphical user interfaces.

Auditory Outcomes with Hearing Rehabilitation in Children with Unilateral Hearing Loss: A Systematic Review.

PubMed

Appachi, Swathi; Specht, Jessica L; Raol, Nikhila; Lieu, Judith E C; Cohen, Michael S; Dedhia, Kavita; Anne, Samantha

2017-10-01

Objective Options for management of unilateral hearing loss (UHL) in children include conventional hearing aids, bone-conduction hearing devices, contralateral routing of signal (CROS) aids, and frequency-modulating (FM) systems. The objective of this study was to systematically review the current literature to characterize auditory outcomes of hearing rehabilitation options in UHL. Data Sources PubMed, EMBASE, Medline, CINAHL, and Cochrane Library were searched from inception to January 2016. Manual searches of bibliographies were also performed. Review Methods Studies analyzing auditory outcomes of hearing amplification in children with UHL were included. Outcome measures included functional and objective auditory results. Two independent reviewers evaluated each abstract and article. Results Of the 249 articles identified, 12 met inclusion criteria. Seven articles solely focused on outcomes with bone-conduction hearing devices. Outcomes favored improved pure-tone averages, speech recognition thresholds, and sound localization in implanted patients. Five studies focused on FM systems, conventional hearing aids, or CROS hearing aids. Limited data are available but suggest a trend toward improvement in speech perception with hearing aids. FM systems were shown to have the most benefit for speech recognition in noise. Studies evaluating CROS hearing aids demonstrated variable outcomes. Conclusions Data evaluating functional and objective auditory measures following hearing amplification in children with UHL are limited. Most studies do suggest improvement in speech perception, speech recognition in noise, and sound localization with a hearing rehabilitation device.

Dynamics of blood flow in a microfluidic ladder network

NASA Astrophysics Data System (ADS)

Maddala, Jeevan; Zilberman-Rudenko, Jevgenia; McCarty, Owen

The dynamics of a complex mixture of cells and proteins, such as blood, in perturbed shear flow remains ill-defined. Microfluidics is a promising technology for improving the understanding of blood flow under complex conditions of shear; as found in stent implants and in tortuous blood vessels. We model the fluid dynamics of blood flow in a microfluidic ladder network with dimensions mimicking venules. Interaction of blood cells was modeled using multiagent framework, where cells of different diameters were treated as spheres. This model served as the basis for predicting transition regions, collision pathways, re-circulation zones and residence times of cells dependent on their diameters and device architecture. Based on these insights from the model, we were able to predict the clot formation configurations at various locations in the device. These predictions were supported by the experiments using whole blood. To facilitate platelet aggregation, the devices were coated with fibrillar collagen and tissue factor. Blood was perfused through the microfluidic device for 9 min at a physiologically relevant venous shear rate of 600 s-1. Using fluorescent microscopy, we observed flow transitions near the channel intersections and at the areas of blood flow obstruction, which promoted larger thrombus formation. This study of integrating model predictions with experimental design, aids in defining the dynamics of blood flow in microvasculature and in development of novel biomedical devices.

Hearing Impairments. Tech Use Guide: Using Computer Technology.

ERIC Educational Resources Information Center

Council for Exceptional Children, Reston, VA. Center for Special Education Technology.

One of nine brief guides for special educators on using computer technology, this guide focuses on advances in electronic aids, computers, telecommunications, and videodiscs to assist students with hearing impairments. Electronic aids include hearing aids, telephone devices for the deaf, teletypes, closed captioning systems for television, and…

21 CFR 874.1820 - Surgical nerve stimulator/locator.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Surgical nerve stimulator/locator. 874.1820... (CONTINUED) MEDICAL DEVICES EAR, NOSE, AND THROAT DEVICES Diagnostic Devices § 874.1820 Surgical nerve stimulator/locator. (a) Identification. A surgical nerve stimulator/locator is a device that is intended to...

Ergonomic evaluation of slide boards used by home care aides to assist client transfers.

PubMed

Sun, Chuan; Buchholz, Bryan; Quinn, Margaret; Punnett, Laura; Galligan, Catherine; Gore, Rebecca

2018-07-01

Home care aides risk musculoskeletal injury because they lift and move clients; the body weight of most adults exceeds the NIOSH recommended limit for lifting. Methods to reduce manual patient lifting in institutional settings are often technically or economically infeasible in home care. Our goal was to identify suitable, safe, low-technology transfer devices for home care use. Sixteen experienced home care aides performed client transfers from wheelchair to bed (upward) and bed to wheelchair (downward) in a simulated home care environment (laboratory), using four different slide boards and by hand without a device. Aides' hand forces were measured during client transfers; aides also evaluated usability of each board. Hand forces exerted while using slide boards were mostly lower than in manual transfer, and forces were lower in downward versus upward transfers. Aides judged a board with a sliding mechanism easier to use than boards without a sliding mechanism. Practitioner Summary: This paper provides quantitative biomechanical measurements showing that slide boards reduced the hand forces needed by home care aides to transfer clients from bed to wheel chair and vice versa, compared to manual lifting. Using a semi-quantitative usability survey, aides identified boards with a sliding mechanism easiest to use.

Denver RTD's computer aided dispatch/automatic vehicle location system : the human factors consequences

DOT National Transportation Integrated Search

1999-09-01

This report documents what happened to employees' work procedures when their employer when their employer installed Computer Aided Disptach/Automatic Vehicle Locator (CAD/AVL) technology to provide real-time surveillance of vehicles and to upgrade ra...

Perceptions of the Design of Voice Output Communication Aids

ERIC Educational Resources Information Center

Judge, Simon; Townend, Gillian

2013-01-01

Background: Voice output communication aids (VOCAs) are a key form of aided communication within the field of augmentative and alternative communication (AAC). In recent years, rapid developments in technology have resulted in an explosion of devices available commercially, yet little research has been conducted into what people who use VOCAs…

30 CFR 57.15031 - Location of self-rescue devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... around mobile equipment, self-rescue devices may be placed in a readily accessible location on such... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of self-rescue devices. 57.15031... Protection Underground Only § 57.15031 Location of self-rescue devices. (a) Except as provided in paragraph...

Reading aids for adults with low vision

PubMed Central

Virgili, Gianni; Acosta, Ruthy; Grover, Lori L; Bentley, Sharon A; Giacomelli, Giovanni

2014-01-01

Background The purpose of low-vision rehabilitation is to allow people to resume or to continue to perform daily living tasks, with reading being one of the most important. This is achieved by providing appropriate optical devices and special training in the use of residual-vision and low-vision aids, which range from simple optical magnifiers to high-magnification video magnifiers. Objectives To assess the effects of reading aids for adults with low vision. Search methods We searched CENTRAL (which contains the Cochrane Eyes and Vision Group Trials Register) (The Cochrane Library 2013, Issue 1), Ovid MEDLINE, Ovid MEDLINE In-Process and Other Non-Indexed Citations, Ovid MEDLINE Daily, Ovid OLDMEDLINE, (January 1950 to January 2013), EMBASE (January 1980 to January 2013), Latin American and Caribbean Literature on Health Sciences (LILACS) (January 1982 to January 2013), OpenGrey (System for Information on Grey Literature in Europe) (www.opengrey.eu/), the metaRegister of Controlled Trials (mRCT) (www.controlled-trials.com), ClinicalTrials.gov (www.clinicaltrials.gov/) and the WHO International Clinical Trials Registry Platform (ICTRP) (www.who.int/ictrp/search/en). We did not use any date or language restrictions in the electronic searches for trials. We last searched the electronic databases on 31 January 2013. We searched the reference lists of relevant articles and used the Science Citation Index to find articles that cited the included studies and contacted investigators and manufacturers of low-vision aids. We handsearched the British Journal of Visual Impairment from 1983 to 1999 and the Journal of Visual Impairment and Blindness from 1976 to 1991. Selection criteria This review includes randomised and quasi-randomised trials in which any device or aid used for reading had been compared to another device or aid in people aged 16 or over with low vision as defined by the study investigators. Data collection and analysis At least two authors independently assessed trial quality and extracted data. Main results We included nine small studies with a cross-over-like design (181 people overall) and one study with three parallel arms (243 participants) in the review. All studies reported the primary outcome, results for reading speed. Two studies including 92 participants found moderate- or low-quality evidence suggesting that reading speed is higher with stand-mounted electronic devices or electronic devices with the camera mounted in a ‘mouse’ than with optical magnifiers, which in these trials were generally stand-mounted or, less frequently, hand-held magnifiers or microscopic lenses. In another study of 20 participants there was moderate-quality evidence that optical devices are better than head-mounted electronic devices (four types). There was low-quality evidence from three studies (93 participants) that reading using head-mounted electronic devices is slower than with stand-based electronic devices. The technology of electronic devices may have changed and improved since these studies were conducted. One study suggested no difference between a diffractive spectacle-mounted magnifier and either refractive (15 participants) or aplanatic (15 participants) magnifiers. One study of 10 people suggested that several overlay coloured filters were no better and possibly worse than a clear filter. A parallel-arm study including 243 participants with age-related macular degeneration found that custom or standard prism spectacles were no different from conventional reading spectacles, although the data did not allow precise estimates of performance to be made. Authors' conclusions There is insufficient evidence on the effect of different types of low-vision aids on reading performance. It would be necessary to investigate which patient characteristics predict performance with different devices, including costly electronic devices. Better-quality research should also focus on assessing sustained long-term use of each device. Authors of studies testing several devices on the same person should consider design and reporting issues related to their sequential presentation and to the cross-over-like study design. PMID:24154864

46 CFR 28.210 - First aid equipment and training.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false First aid equipment and training. 28.210 Section 28.210....210 First aid equipment and training. (a) Each vessel must have on board a complete first aid manual... location. (b) First aid and cardiopulmonary resuscitation (CPR) course certification. Certification in...

Technologies for the marking of fishing gear to identify gear components entangled on marine animals and to reduce abandoned, lost or otherwise discarded fishing gear.

PubMed

He, Pingguo; Suuronen, Petri

2018-04-01

Fishing gears are marked to establish and inform origin, ownership and position. More recently, fishing gears are marked to aid in capacity control, reduce marine litter due to abandoned, lost or otherwise discarded fishing gear (ALDFG) and assist in its recovery, and to combat illegal, unreported and unregulated (IUU) fishing. Traditionally, physical marking, inscription, writing, color, shape, and tags have been used for ownership and capacity purposes. Buoys, lights, flags, and radar reflectors are used for marking of position. More recently, electronic devices have been installed on marker buoys to enable easier relocation of the gear by owner vessels. This paper reviews gear marking technologies with focus on coded wire tags, radio frequency identification tags, Automatic Identification Systems, advanced electronic buoys for pelagic longlines and fish aggregating devices, and re-location technology if the gear becomes lost. Copyright © 2018 Elsevier Ltd. All rights reserved.

[Design and application of implantable medical device information management system].

PubMed

Cao, Shaoping; Yin, Chunguang; Zhao, Zhenying

2013-03-01

Through the establishment of implantable medical device information management system, with the aid of the regional joint sharing of resources, we further enhance the implantable medical device traceability management level, strengthen quality management, control of medical risk.

The Sonic Glasses Evaluated

ERIC Educational Resources Information Center

Kay, Leslie

1973-01-01

Two questionnaires (169 items for the 94 users of the aid, 88 for the 21 trainers) were employed to evaluate the ultrasonic binaural sensory aid for the blind, a mobility and orientation device. (Author)

77 FR 14989 - Medicare Program; Revisions to the Durable Medical Equipment, Prosthetics, Orthotics, and...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-14

... wheelchairs. Prosthetic devices are included in the definition of ``medical and other health services'' in section 1861(s)(8) of the Act. Prosthetic devices are defined as devices (other than dental) which replace... examples of prosthetic devices include cardiac pacemakers, cochlear implants, electrical continence aids...

The Future of Adult Cardiac Assist Devices: Novel Systems and Mechanical Circulatory Support Strategies

PubMed Central

Bartoli, Carlo R.; Dowling, Robert D.

2011-01-01

Synopsis The recent, widespread success of mechanical circulatory support has ushered in a new era of cardiovascular medicine in which numerous implantable devices exist to treat advanced heart failure. As cardiac assist devices gain prevalence in the clinical management of cardiovascular disease, it is increasingly important to raise awareness of novel device systems, the unique mechanisms by which they function, and implications for patient management. In this article, we present state-of-the-art devices that are currently under development or in clinical trials. Devices are categorized as Standard Full-Support (HeartMate III, CorAide, Evaheart LVAS), Less-Invasive Full-Support (MVAD), Partial-Support (CircuLite Synergy Pocket Micro-Pump, Reitan Catheter Pump, Procyrion CAD, C-Pulse, Symphony Counterpulsation Device) Right Ventricular Assist Device (RVAD; DexAide, Impella RD Recover, Impella RP), and Total Artificial Heart (TAH; CardioWest, AbioCor II, Continuous-Flow TAH, Continuous-Flow BiVAD). Implantation strategy, mechanism of action, durability, efficacy, hemocompatibility, and human factors such as quality of life during device support are considered. The feasibility of novel strategies for unloading the failing heart is examined. PMID:22062206

21 CFR 801.420 - Hearing aid devices; professional and patient labeling.

Code of Federal Regulations, 2014 CFR

2014-04-01

... damage the hearing aid, such as dropping, immersing, or exposing the hearing aid to excessive heat. (vii... strongly discouraged. children with hearing loss In addition to seeing a physician for a medical evaluation, a child with a hearing loss should be directed to an audiologist for evaluation and rehabilitation...

JOB PERFORMANCE AIDS AND THEIR IMPACT ON MANPOWER UTILIZATION.

ERIC Educational Resources Information Center

CHALUPSKY, ALBERT B.; KOPF, THOMAS J.

THE PURPOSE OF THE STUDY WAS TO REVIEW AND SYNTHESIZE THE RESULTS OF RESEARCH ON JOB PERFORMANCE AIDS AND EXPLORE THEIR CURRENT AND POTENTIAL ON INDUSTRIAL MANPOWER UTILIZATION. JOB PERFORMANCE AIDS ARE AUXILIARY INFORMATION STORAGE DEVICES WHICH PRESENT JOB INSTRUCTIONS OR REFERENCE DATA FOR USE BY THE EMPLOYEE DURING THE COURSE OF HIS JOB…

Sensory Aids Research Project - Clarke School for the Deaf.

ERIC Educational Resources Information Center

Boothroyd, Arthur

Described is a program of research into sensory aids for the deaf, emphasizing research on factors involved in the effective use of sensory aids rather than evaluation of particular devices. Aspects of the program are the development of a programed testing and training unit, the control of fundamental voice frequency using visual feedback, and…

33 CFR 67.10-5 - Location requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Location requirements. 67.10-5 Section 67.10-5 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION AIDS TO NAVIGATION ON ARTIFICIAL ISLANDS AND FIXED STRUCTURES General Requirements for Sound...

21 CFR 878.4320 - Removable skin clip.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Removable skin clip. 878.4320 Section 878.4320...) MEDICAL DEVICES GENERAL AND PLASTIC SURGERY DEVICES Surgical Devices § 878.4320 Removable skin clip. (a) Identification. A removable skin clip is a clip-like device intended to connect skin tissues temporarily to aid...

76 FR 34845 - Medical Devices; Ear, Nose, and Throat Devices; Classification of the Wireless Air-Conduction...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-06-15

... control by other users with a similar medical device. Exposure to non-ionizing radiation Wireless... Administration (FDA) is classifying the wireless air-conduction hearing aid into class II (special controls). The Agency is classifying the device into class II (special controls) in order to provide a reasonable...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2010 CFR

2010-01-01

... with impaired vision), crutches, and walkers; and (3) Other assistive devices for stowage or use within... syringes or auto-injectors, vision-enhancing devices, and POCs, ventilators and respirators that use non...

AEDs at your fingertips: automated external defibrillators on college campuses and a novel approach for increasing accessibility.

PubMed

Berger, Ryan J; O'Shea, Jesse G

2014-01-01

The use of automated external defibrillators (AEDs) increases survival in cardiac arrest events. Due to the success of previous efforts and free, readily available mobile mapping software, the discussion is to emphasize the importance of the use of AEDs to prevent sudden cardiac arrest-related deaths on college campuses and abroad, while suggesting a novel approach to aiding in access and awareness issues. A user-friendly mobile application (a low-cost iOS map) was developed at Florida State University to decrease AED retrieval distance and time. The development of mobile AED maps is feasible for a variety of universities and other entities, with the potential to save lives. Just having AEDs installed is not enough--they need to be easily locatable. Society increasingly relies on phones to provide information, and there are opportunities to use mobile technology to locate and share information about relevant emergency devices; these should be incorporated into the chain of survival.

Instructional Aids in Mathematics: Using Models as Instructional Aids

ERIC Educational Resources Information Center

Johnson, Donovan A.; And Others

1973-01-01

Models are discussed both as concrete representations of mental constructs and as various manipulative devices. Illustrations of effective model use, suggestions for acquiring models, and lists of models for specific concepts are included. (LS)

The benefits of hearing aids and closed captioning for television viewing by older adults with hearing loss

PubMed Central

Gordon-Salant, Sandra; Callahan, Julia S.

2010-01-01

Objectives Although watching television is a common leisure activity of older adults, the ability to understand televised speech may be compromised by age-related hearing loss. Two potential assistive devices for improving television viewing are hearing aids and closed captioning, but their use and benefit by older adults with hearing loss are unknown. The primary purpose of this initial investigation was to determine if older hearing-impaired adults show improvements in understanding televised speech with the use of these two assistive devices (hearing aids and closed captioning) compared to conditions without these devices. A secondary purpose was to examine the frequency of hearing aid use and closed captioning use among a sample of older hearing aid wearers. Design The investigation entailed a randomized, repeated-measures design of 15 older adults (59–82 years) with bilateral sensorineural hearing losses who wore hearing aids. Participants viewed three types of televised programs (news, drama, game show) that were each edited into lists of speech segments, and provided an identification response. Each participant was tested in four conditions: baseline (no hearing aids or closed captioning), hearing aids only, closed captioning only, and hearing aids + closed captioning. Pilot testing with young normal-hearing listeners was conducted also to establish list equivalence and stimulus intelligibility with a control group. All testing was conducted in a quiet room to simulate a living room, using a 19-in flat screen television. Questionnaires were also administered to participants to determine frequency of hearing aid use and closed captioning use while watching television. Results A significant effect of viewing condition was observed for all programs. Participants exhibited significantly better speech recognition scores in conditions with closed captioning than those without closed captioning (p<.01). Use of personal hearing aids did not significantly improve recognition of televised speech compared to the unaided condition. The condition effect was similar across the three different programs. Most of the participants (73%) regularly wore their hearing aids while watching television; very few of them (13%) had ever used closed captioning. Conclusions On average, use of closed captioning while watching television dramatically improved speech understanding by a sample of older hearing-impaired adults compared to conditions without closed captioning, including when hearing aids were worn. PMID:19444122

21 CFR 866.5380 - Free secretory component immuno-logical test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... body fluids. Measurement of free secretory component (protein molecules) aids in the diagnosis or... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 866.5380 - Free secretory component immuno-logical test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... body fluids. Measurement of free secretory component (protein molecules) aids in the diagnosis or... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 866.5380 - Free secretory component immuno-logical test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... body fluids. Measurement of free secretory component (protein molecules) aids in the diagnosis or... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 866.5380 - Free secretory component immuno-logical test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... body fluids. Measurement of free secretory component (protein molecules) aids in the diagnosis or... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 862.1630 - Protein (fractionation) test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test... body fluids. Protein fractionations are used as an aid in recognizing abnormal proteins in body fluids...

21 CFR 862.1630 - Protein (fractionation) test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test... body fluids. Protein fractionations are used as an aid in recognizing abnormal proteins in body fluids...

21 CFR 862.1630 - Protein (fractionation) test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test... body fluids. Protein fractionations are used as an aid in recognizing abnormal proteins in body fluids...

21 CFR 862.1630 - Protein (fractionation) test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... (CONTINUED) MEDICAL DEVICES CLINICAL CHEMISTRY AND CLINICAL TOXICOLOGY DEVICES Clinical Chemistry Test... body fluids. Protein fractionations are used as an aid in recognizing abnormal proteins in body fluids...

30 CFR 56.19095 - Location of signal devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Location of signal devices. 56.19095 Section 56.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Signaling § 56.19095 Location of signal devices. Hoisting signal devices shall be positioned within easy...

30 CFR 57.19095 - Location of signal devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Location of signal devices. 57.19095 Section 57.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Signaling § 57.19095 Location of signal devices. Hoisting signal devices shall be positioned...

47 CFR 15.703 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... channels on which the Mode I device, but not the fixed device, may operate. (d) Geo-location capability.../portable device. A personal/portable TVBD that does not use an internal geo-location capability and access.../portable device. A personal/portable TVBD that uses an internal geo-location capability and access to a TV...

30 CFR 56.19095 - Location of signal devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of signal devices. 56.19095 Section 56.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Signaling § 56.19095 Location of signal devices. Hoisting signal devices shall be positioned within easy...

30 CFR 57.19095 - Location of signal devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Location of signal devices. 57.19095 Section 57.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Signaling § 57.19095 Location of signal devices. Hoisting signal devices shall be positioned...

30 CFR 56.19095 - Location of signal devices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Location of signal devices. 56.19095 Section 56.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Signaling § 56.19095 Location of signal devices. Hoisting signal devices shall be positioned within easy...

30 CFR 57.19095 - Location of signal devices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Location of signal devices. 57.19095 Section 57.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Signaling § 57.19095 Location of signal devices. Hoisting signal devices shall be positioned...

30 CFR 57.19095 - Location of signal devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Location of signal devices. 57.19095 Section 57.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Signaling § 57.19095 Location of signal devices. Hoisting signal devices shall be positioned...

30 CFR 56.19095 - Location of signal devices.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Location of signal devices. 56.19095 Section 56.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Signaling § 56.19095 Location of signal devices. Hoisting signal devices shall be positioned within easy...

30 CFR 56.19095 - Location of signal devices.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Location of signal devices. 56.19095 Section 56.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Signaling § 56.19095 Location of signal devices. Hoisting signal devices shall be positioned within easy...

30 CFR 57.19095 - Location of signal devices.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Location of signal devices. 57.19095 Section 57.19095 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Hoisting Signaling § 57.19095 Location of signal devices. Hoisting signal devices shall be positioned...

Computed tomography-assisted laparoscopic removal of intraabdominally migrated levonorgestrel-releasing intrauterine systems.

PubMed

Mahmoud, Mohamad S; Merhi, Zaher O

2010-04-01

To report three cases of migrated levonorgestrel intrauterine device (LNG-IUS) into the pelvic/abdominal cavity removed laparoscopically with the aid of preoperative computed tomography (CT) scan imaging. Three patients presenting with a missing LNG-IUS on examination and pelvic ultrasound are presented. A preoperative CT scan was performed, what helped in a successful removal of the LNG-IUS. The patients were discharged home the same day of the procedure. Our cases reinforce, besides the diagnosis of a migrated LNG-IUS by ultrasound, the fact that preoperative CT scan imaging assists in the diagnosis of the precise location of a migrated LNG-IUS into the pelvic/abdominal cavity and helps the physician in the prediction of the difficulty of the laparoscopic removal.

A Computer-Based, Interactive Videodisc Job Aid and Expert System for Electron Beam Lithography Integration and Diagnostic Procedures.

ERIC Educational Resources Information Center

Stevenson, Kimberly

This master's thesis describes the development of an expert system and interactive videodisc computer-based instructional job aid used for assisting in the integration of electron beam lithography devices. Comparable to all comprehensive training, expert system and job aid development require a criterion-referenced systems approach treatment to…

EVALUATION AND DEVELOPMENT OF SENSORY AIDS AND DEVICES. FINAL REPORT. (TITLE SUPPLIED).

ERIC Educational Resources Information Center

Massachusetts Inst. of Tech., Cambridge. Sensory Aids Evaluation and Development Center.

THIS REPORT PRESENTS INFORMATION ON THE DEVELOPMENT AND EVALUATION OF SENSORY AIDS AT THE SENSORY AIDS EVALUATION AND DEVELOPMENT CENTER AT THE MASSACHUSETTS INSTITUTE OF TECHNOLOGY (MIT) BETWEEN OCTOBER 1965 AND NOVEMBER 1966. INCLUDED ARE (1) THE DESIGN, CONSTRUCTION, AND TESTING OF A RELIABLE MONOTYPE TAPE READER WHICH WILL BE USED IN…

Availability and Placement of Electronic Nicotine Delivery Systems at the Point-of-Sale.

PubMed

Wagoner, Kimberly G; Song, Eunyoung; King, Jessica; Egan, Kathleen L; Debinski, Beata; Wolfson, Mark; Spangler, John; Sutfin, Erin L

2017-09-09

Electronic nicotine delivery systems (ENDS) are widely available and come in a variety of forms, including disposable cigalikes and refillable tank systems. However, little is known about their placement at the point-of-sale. We explored the placement of various ENDS types among tobacco retailers. Systematic assessments at the point-of-sale were completed by trained data collectors in 90 tobacco retailers, including grocery stores, convenience stores, and pharmacies in North Carolina, U.S. Availability and placement of various ENDS types including cigalikes, e-hookahs, tank systems and e-liquids was recorded. Almost all retailers (97.8%) sold cigalikes; 41.4% sold devices labeled as e-hookahs; 54.4% sold tank systems and 56.2% sold e-liquids. Fewer than half of stores placed ENDS exclusively behind the counter; significant differences in ENDS placement were found by store type. Grocery stores carried cigalikes, tank systems and e-liquids and placed them exclusively behind the counter. Pharmacies only sold cigalikes; most placed them exclusively behind the counter (91.7%) with cessation aids and other tobacco products. Convenience stores carried all ENDS types and placed them with other tobacco products (55.1%) and candy (17.4%). Only about one-third of convenience stores placed ENDS exclusively behind the counter. This exploratory study shows ENDS availability and placement at the point-of-sale varies by retailer type. Pharmacies placed cigalikes with cessation aids behind the counter suggesting their ability to aid in smoking cessation. Most convenience stores placed ENDS in self-service locations, making them easily accessible to youth. Findings highlight the need for ENDS regulation at the point-of-sale. Our study highlights the need for regulatory efforts aimed at ENDS placement at the point-of-sale. While pharmacies and grocery stores offered fewer ENDS types and typically placed them in clerk-assisted locations, all ENDS types were found at convenience stores, some of which were placed in youth-friendly locations. Regulatory efforts to control ENDS placement and limit youth exposure should be examined, such as requiring products be placed in clerk-assisted locations and banning ENDS placement next to candy. © The Author 2017. Published by Oxford University Press on behalf of the Society for Research on Nicotine and Tobacco. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Hearing aid and cochlear implant use in children with hearing loss at three years of age: Predictors of use and predictors of changes in use

PubMed Central

Marnane, Vivienne; Ching, Teresa YC

2015-01-01

Objective To examine usage patterns of hearing aids and cochlear implants in children up to three years of age, how usage changes longitudinally, and factors associated with device usage. Design Parent report and Parent’s Evaluation of Aural/oral performance of Children (PEACH) data were obtained at six and twelve months after hearing-aid fitting or cochlear implant switch-on, and again at three years of age. The effect of device use on auditory functional performance was investigated using the PEACH questionnaire. Study sample Four hundred and thirteen participants from the Longitudinal Outcomes of Children with Hearing Impairment (LOCHI) study were included for analysis. Result For users of hearing aids, higher usage at three years was associated with higher maternal education, and more severe hearing loss. For users of cochlear implants, higher usage was associated with higher maternal education and the absence of additional disabilities. Higher PEACH scores was associated with higher usage scores. After allowing for the effects of demographic characteristics, device use was not a significant predictor of functional performance. Conclusions Sixty-two percent of children achieved consistent use (>75% of waking hours) within the first year of receiving a hearing aid or a cochlear implant, and 71% by three years of age. PMID:25816866

A surgical confocal microlaparoscope for real-time optical biopsies

NASA Astrophysics Data System (ADS)

Tanbakuchi, Anthony Amir

The first real-time fluorescence confocal microlaparoscope has been developed that provides instant in vivo cellular images, comparable to those provided by histology, through a nondestructive procedure. The device includes an integrated contrast agent delivery mechanism and a computerized depth scan system. The instrument uses a fiber bundle to relay the image plane of a slit-scan confocal microlaparoscope into tissue. The confocal laparoscope was used to image the ovaries of twenty-one patients in vivo using fluorescein sodium and acridine orange as the fluorescent contrast agents. The results indicate that the device is safe and functions as designed. A Monte Carlo model was developed to characterize the system performance in a scattering media representative of human tissues. The results indicate that a slit aperture has limited ability to image below the surface of tissue. In contrast, the results show that multi-pinhole apertures such as a Nipkow disk or a linear pinhole array can achieve nearly the same depth performance as a single pinhole aperture. The model was used to determine the optimal aperture spacing for the multi-pinhole apertures. The confocal microlaparoscope represents a new type of in vivo imaging device. With its ability to image cellular details in real time, it has the potential to aid in the early diagnosis of cancer. Initially, the device may be used to locate unusual regions for guided biopsies. In the long term, the device may be able to supplant traditional biopsies and allow the surgeon to identify early stage cancer in vivo.

33 CFR 66.01-5 - Application procedure.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Section 66.01-5 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION PRIVATE AIDS TO NAVIGATION Aids to Navigation Other Than Federal or State § 66.01-5 Application... located. You can find application form CG-2554 at http://www.uscgboating.org/safety/aton/aids.htm. You...

Clinical evaluation of an over-the-counter hearing aid (TEO First®) in elderly patients suffering of mild to moderate hearing loss.

PubMed

Sacco, Guillaume; Gonfrier, Sébastien; Teboul, Bernard; Gahide, Ivan; Prate, Fredéric; Demory-Zory, Mathilde; Turpin, Jean-Michel; Vuagnoux, Claire; Genovese, Philippe; Schneider, Stéphane; Guérin, Olivier; Guevara, Nicolas

2016-07-09

Presbycusis has a direct influence on autonomy of the elderly but hearing aids lack of affordability. Moreover a recent review demonstrate that electroacoustic characteristics of OTC hearing aids were generally not suitable for the elderly people. In our study, we assessed the clinical value of a new over-the-counter (OTC) hearing aid device (TEO First®) in the elderly. This prospective monocentric open label study included patients over 60 years of age with a mild to moderate presbycusis. Patients were assessed with acceptable noise level test (ANL), pure tone (PTA) and speech (SA) audiometry in silent and noisy environment, with and without TEO First®. A Glasgow Hearing Aid Benefit Profile, acceptability and satisfaction surveys were completed after one month of using the device. Thirty one patients were included. There was an improvement of hearing with TEO First® in silence (SA: +39.2 %, p < 0.01; PTA: -9.04 dB, p < 0.01) or in noise (SA +47.7 %, p < 0.01; PTA: -5.23 dB, p < 0.05). After one month of use of the device, quality of life has improved with regards to the following parameters: decrease of perceived hearing difficulties during conversation without background noise (-9.6 % p = 0.018), in conversation with several people (-16.2 % p = 0.0076), decrease of negative emotions while watching TV (-18.5 % p = 0.011), during conversation without background noise (-16.5 % p = 0.0024), during conversation in noisy background (-17.1 % p = 0.027) and during conversation with several people (-20 % p = 0.014). The acceptability of the device was low to moderate. TEO First® is an effective OTC hearing aid that improves the patient's quality of life. Current Controlled Trials NCT01815788.

Computer-aided design/computer-aided manufacturing skull base drill.

PubMed

Couldwell, William T; MacDonald, Joel D; Thomas, Charles L; Hansen, Bradley C; Lapalikar, Aniruddha; Thakkar, Bharat; Balaji, Alagar K

2017-05-01

The authors have developed a simple device for computer-aided design/computer-aided manufacturing (CAD-CAM) that uses an image-guided system to define a cutting tool path that is shared with a surgical machining system for drilling bone. Information from 2D images (obtained via CT and MRI) is transmitted to a processor that produces a 3D image. The processor generates code defining an optimized cutting tool path, which is sent to a surgical machining system that can drill the desired portion of bone. This tool has applications for bone removal in both cranial and spine neurosurgical approaches. Such applications have the potential to reduce surgical time and associated complications such as infection or blood loss. The device enables rapid removal of bone within 1 mm of vital structures. The validity of such a machining tool is exemplified in the rapid (< 3 minutes machining time) and accurate removal of bone for transtemporal (for example, translabyrinthine) approaches.

Field testing of two electronic mobility aid devices for persons who are deaf-blind.

PubMed

Vincent, Claude; Routhier, François; Martel, Valérie; Mottard, Marie-Ève; Dumont, Frédéric; Côté, Lise; Cloutier, Danielle

2014-09-01

To test a methodology for assessing the effects of electronic mobility aid devices (EMAD) on the mobility of persons who are deaf-blind in real-life situations. A single-subject desing was done with four users followed in a program for persons who are deaf-blind. Participants were trained to use two commercial EMADs: the Miniguide and the Breeze. The Canadian Measure of Occupational Performance (CMOP) was administered before training (T1), after training (T2) and three months later (T3). The Quebec User Evaluation of Satisfaction with assistive Technology (QUEST) was administered at T2 and T3. A follow-up interview was conducted with the participants and clinicians at T3 to evaluate the benefits of the EMAD and any problems. CMOP suggests that both performance and satisfaction improved following the use of both EMADs in four occupations (functional mobility, active leisure, community life and socialization). QUEST indicates high satisfaction with eight items except for one participant. Follow-up interviews revealed a wide variety of perceptions regarding EMAD use and seven problems although CMOP and QUEST indicated good satisfaction. A high satisfaction score on QUEST does not necessarily imply that an assistive device is efficient in all circumstances; follow-up interviews provided important complementary information. For people who are deaf-blind The Miniguide is reliable for detecting obstacles (vibrations are sent as a warning when approaching an obstacle). It is often used to know if taking the right route. It identifies entrances or openings (indicated by the vibrations stopping when pointing at a wall), which can replace the echo-location for blind persons with hearing impairments. The Miniguide helped to locate overhanging objects which are not detectable with a long cane. The Breeze can record landmarks for orientation and it possible to use those landmarks to go back alone later after taking a certain route for the first time with someone else. It helps to familiarize the person with new places. It can tell you where you are at any time. It helps with orientation and the participant also liked this feature because it helped with learning street names. The Miniguide and the Breeze were not efficient in all circumstances; there were some problems with the ergonomic (both), detecting snow banks (Miniguide), sensitiveness to the surroundings in crowded places (Miniguide) and exactitude for geo-localization (Breeze).

Development and evaluation of a new taxonomy of mobility-related assistive technology devices.

PubMed

Shoemaker, Laura L; Lenker, James A; Fuhrer, Marcus J; Jutai, Jeffrey W; Demers, Louise; DeRuyter, Frank

2010-10-01

This article reports on the development of a new taxonomy for mobility-related assistive technology devices. A prototype taxonomy was created based on the extant literature. Five mobility device experts were engaged in a modified Delphi process to evaluate and refine the taxonomy. Multiple iterations of expert feedback and revision yielded consensual agreement on the structure and terminology of a new mobility device taxonomy. The taxonomy uses a hierarchical framework to classify ambulation aids and wheeled mobility devices, including their key features that impact mobility. Five attributes of the new taxonomy differentiate it from previous mobility-related device classifications: (1) hierarchical structure, (2) primary device categories are grouped based on their intended mobility impact, (3) comprehensive inclusion of technical features, (4) a capacity to assimilate reimbursement codes, and (5) availability of a detailed glossary. The taxonomy is intended to support assistive technology outcomes research. The taxonomy will enable researchers to capture mobility-related assistive technology device interventions with precision and provide a common terminology that will allow comparisons among studies. The prominence of technical features within the new taxonomy will hopefully promote research that helps clinicians predict how devices will perform, thus aiding clinical decision making and supporting funding recommendations.

Restoration of hearing by hearing aids: conventional hearing aids – implantable hearing aids – cochlear implants – auditory brainstem implants

PubMed Central

Leuwer, R.; Müller, J.

2005-01-01

Aim of this report is to explain the current concept of hearing restoration using hearing aids. At present the main issues of conventional hearing aids are the relative benefits of analogue versus digital devices and different strategies for the improvement of hearing in noise. Implantable hearing aids provide a better sound quality and less distortion. The lack of directional microphones is the major disadvantage of the partially implantable hearing aids commercially available. Two different clinical studies about fully implantable hearing aids have been started in 2004. One of the most-promising developments seems to be the electric-acoustic stimulation. PMID:22073051

77 FR 31274 - Hazardous Materials: Harmonization With the United Nations Recommendations on the Transport of...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... (ICAO) Dangerous Goods Panel (DGP) regarding certain lithium ion battery-powered mobility aids (e.g... devices on an aircraft and providing for the intentional removal of a lithium ion battery from a device... limit lithium ion batteries used to power portable electronic devices and medical devices to 160 watt...

Applicability of a new robotic walking aid in a patient with cerebral palsy. Case report.

PubMed

Smania, N; Gandolfi, M; Marconi, V; Calanca, A; Geroin, C; Piazza, S; Bonetti, P; Fiorini, P; Cosentino, A; Capelli, C; Conte, D; Bendinelli, M; Munari, D; Ianes, P; Fiaschi, A; Picelli, A

2012-03-01

Gait training with the help of assistive technological devices is an innovative field of research in neurological rehabilitation. Most of the available gait training devices do not allow free movement in the environment, which would be the most suitable natural and motivating condition for training children with neurological gait impairment. To evaluate the potential applicability of a new robotic walking aid as a tool for gait training in non-ambulatory children with Cerebral Palsy. Single case study Outpatient regimen A 11-years-old child unable to stand and walk independently as a result of spastic tetraplegic cerebral palsy (CP). The experimental device was a newly actuated version of a dynamic combined walking and standing aid (NF-Walker®) available in the market which was modified by means of two pneumatic artificial muscles driven by a foot-switch inserted in the shoes. The child was tested at baseline (while maintaining the standing position aided by the non-actuated NF-Walker®) and in the experimental condition (while using the actuated robotic aid). The outcome measures were: 2-minute walking test, 10-metre walking test, respiratory and heart parameters, energy cost of locomotion. At baseline, the child was unable to perform any autonomous form of locomotion. When assisted by the actuated aid (i.e. during the experimental condition), the child was successful in moving around in his environment. His performance was 19.63 m in the 2-minute walking test and 64 s in the 10-metre walking test. Respiratory and heart parameters were higher than healthy age-matched children both at baseline and in the experimental condition. The energy cost of gait, which was not valuable in the baseline condition, was significantly higher than normality during the experimental condition. The new robotic walking aid may help children suffering from CP with severe impairment of gait to move around in their environment. This new robotic walking device may have a potential impact in stimulating the development and in training of gait in children with neurological gait impairment. Future studies are warranted in order to test this hypothesis.

Memory device for two-dimensional radiant energy array computers

NASA Technical Reports Server (NTRS)

Schaefer, D. H.; Strong, J. P., III (Inventor)

1977-01-01

A memory device for two dimensional radiant energy array computers was developed, in which the memory device stores digital information in an input array of radiant energy digital signals that are characterized by ordered rows and columns. The memory device contains a radiant energy logic storing device having a pair of input surface locations for receiving a pair of separate radiant energy digital signal arrays and an output surface location adapted to transmit a radiant energy digital signal array. A regenerative feedback device that couples one of the input surface locations to the output surface location in a manner for causing regenerative feedback is also included

Management of Hearing Aid Assembly by Urban-Dwelling Hearing-Impaired Adults in a Developed Country

PubMed Central

Keidser, Gitte; Hartley, Lisa; Caposecco, Andrea; Hickson, Louise; Meyer, Carly

2011-01-01

A self-fitting hearing aid, designed to be assembled and programmed without audiological or computer support, could bring amplification to millions of people in developing countries, who remain unaided due to the lack of a local, professional, audiological infrastructure. The ability to assemble and insert a hearing aid is fundamental to the successful use of a self-fitting device. In this study, the management of such tasks was investigated. Eighty older, urban-dwelling, hearing-impaired adults in a developed country were asked to follow a set of written, illustrated instructions to assemble two slim-fit behind-the-ear hearing aids. Participants were allowed to access assistance with the task from an accompanying partner. A range of personal and audiometric variables was measured through the use of structured questionnaires and standardized tests of health literacy, cognitive function, and manual dexterity. The results showed that 99% of participants were able to complete the hearing aid assembly task, either on their own or with assistance. Health literacy, or the ability to read and understand health-related text, and gender most strongly influenced participants’ ability to complete the assembly task independently and accurately. Higher levels of health literacy were associated with an increased likelihood of independent and successful task completion. Male participants were more likely to complete the task on their own, while female participants were more likely to assemble the device without errors. The results of this study will inform future work regarding development of educational material for the self-fitting hearing aid as well as candidacy for such a device. PMID:22200734

A new oscillating saw for robotic aided surgery.

PubMed

Moctezuma, J L; Schuster, D; Gossé, F; Schulz, H J

1997-01-01

In this paper a brief description of a computer and robotic aided surgery system is given with a detailed overview of the necessity to develop special tools for robotic surgery. The application range of this robotic system has been specially focused on the orthopaedics field and, more particularly, on the execution of osteotomies. It was therefore necessary to develop a new saw device which would meet medical and--from the robot system point of view--mechanical as well as functional requirements. After describing the device which was developed on the basis of these requirements, a detailed comparative study of off-the-shelf oscillating saws and the new device is given at the end of the paper.

Space Derived Health Aids (AID, Heart Monitor)

NASA Technical Reports Server (NTRS)

1981-01-01

CPI's spinoff from miniaturized pace circuitry is the new heart-assist device, the AID implantable automatic pulse generator. AID pulse generator monitors the heart continuously, recognizes onset of fibrillation, then administers a corrective electrical shock. A mini- computer, a power source, and two electrodes which sense heart activity are included in the unit. An associated system was also developed. It includes an external recorder to be worn by AID patients and a physician's console to display the data stored by the recorder. System provides a record of fibrillation occurrences and the ensuing defibrillation.

[Device-aided therapies in advanced Parkinson's disease].

PubMed

Timofeeva, A A

Advanced stages of Parkinson's disease (PD) is a consequence of the severe neurodegenerative process and are characterized by the development of motor fluctuations and dyskinesia, aggravation of non-motor symptoms. Treatment with peroral and transdermal drugs can't provide an adequate control of PD symptoms and quality-of-life of the patients at this stage of disease. Currently, three device-aided therapies: deep brain stimulation (DBS), intrajejunal infusion of duodopa, subcutaneous infusion of apomorphine can be used in treatment of patients with advanced stages of PD. Timely administration of device-aided therapies and right choice of the method determine, to a large extent, the efficacy and safety of their use. Despite the high efficacy of all three methods with respect to the fluctuation of separate symptoms, each method has its own peculiarities. The authors reviewed the data on the expediency of using each method according to the severity of motor and non-motor symptoms, patient's age, PD duration, concomitant pathology and social support of the patients.

Locating difficult veins for venepuncture and cannulation.

PubMed

Shaw, Sally Jane

2017-02-15

Vein location and assessment are essential to improve the success rates for vascular access. However, problems remain with first attempt success rates for peripheral cannulation and locating difficult veins. Practitioners may not be aware of developments in technology and aids to assist in the location and assessment of veins to achieve vascular access. This article provides an overview of two vein location aids that can be used to locate difficult veins: the IV-eye vein imager and the Vacuderm tourniquet. It discusses the patient factors that can increase the difficulty of vein assessment and location, and emphasises the importance of vessel health and preservation, and vein palpation. Practitioners should be experienced and skilled in the assessment of veins, and they are encouraged to revisit how they locate and assess veins.

A Practical Tablet-Based Hearing Aid Configuration as an Exemplar Project for Students of Instrumentation.

PubMed

Simeoni, Ricardo

2015-06-11

This paper presents the configuration and digital signal processing details of a tablet-based hearing aid transmitting wirelessly to standard earphones, whereby the tablet performs full sound processing rather than solely providing a means of setting adjustment by streaming to conventional digital hearing aids. The presented device confirms the recognized advantages of this tablet-based approach (e.g., in relation to cost, frequency domain processing, amplification range, versatility of functionality, component battery rechargeability), and flags the future wider-spread availability of such hearing solutions within mainstream healthcare. The use of a relatively high sampling frequency was found to be beneficial for device performance, while the use of optional off-the-shelf add-on components (e.g., data acquisition device, high fidelity microphone, compact wireless transmitter/receiver, wired headphones) are also discussed in relation to performance optimization. The easy-to-follow configuration utilized is well suited to student learning/research instrumentation projects within the health and biomedical sciences. In this latter regard, the presented device was pedagogically integrated into a flipped classroom approach for the teaching of bioinstrumentation within an Allied Health Sciences School, with the subsequent establishment of positive student engagement outcomes.

Procurement of Library Materials in the Federal Government; An Orientation Aid Prepared for the Federal Library Committee.

ERIC Educational Resources Information Center

Falk, Leslie K.

This handbook is designed primarily as a general orientation aid, not an operation manual. It presents the background (mainly regulatory) of Federal procurement work, details, devices and tactics found to be successful, and calls attention to special sources of supply. Although planned as an aid for librarians who are engaged in Federal…

Hearing aid and hearing assistance technology use in Aotearoa/New Zealand.

PubMed

Kelly-Campbell, Rebecca J; Lessoway, Kamea

2015-05-01

The purpose of this study was to describe factors that are related to hearing aid and hearing assistance technology ownership and use in Aotearoa/New Zealand. Adults with hearing impairment living in New Zealand were surveyed regarding health-related quality of life and device usage. Audiometric data (hearing sensitivity and speech in noise) were collected. Data were obtained from 123 adults with hearing impairment: 73 reported current hearing-aid use, 81 reported current hearing assistance technology use. In both analyses, device users had more difficulty understanding speech in background noise, had poor hearing in both their better and worse hearing ears, and perceived more consequences of hearing impairment in their everyday lives (both emotionally and socially) than non-hearing-aid users. Discriminant analyses showed that the social consequences of hearing impairment and the better ear hearing best classified hearing aid users from non-users but social consequences and worse ear hearing best classified hearing assistance technology users from non-users. Quality of life measurements and speech-in-noise assessments provide useful clinical information. Hearing-impaired adults in New Zealand who use hearing aids also tend to use hearing assistance technology, which has important clinical implications.

Costs incurred by applying computer-aided design/computer-aided manufacturing techniques for the reconstruction of maxillofacial defects.

PubMed

Rustemeyer, Jan; Melenberg, Alex; Sari-Rieger, Aynur

2014-12-01

This study aims to evaluate the additional costs incurred by using a computer-aided design/computer-aided manufacturing (CAD/CAM) technique for reconstructing maxillofacial defects by analyzing typical cases. The medical charts of 11 consecutive patients who were subjected to the CAD/CAM technique were considered, and invoices from the companies providing the CAD/CAM devices were reviewed for every case. The number of devices used was significantly correlated with cost (r = 0.880; p < 0.001). Significant differences in mean costs were found between cases in which prebent reconstruction plates were used (€3346.00 ± €29.00) and cases in which they were not (€2534.22 ± €264.48; p < 0.001). Significant differences were also obtained between the costs of two, three and four devices, even when ignoring the cost of reconstruction plates. Additional fees provided by statutory health insurance covered a mean of 171.5% ± 25.6% of the cost of the CAD/CAM devices. Since the additional fees provide financial compensation, we believe that the CAD/CAM technique is suited for wide application and not restricted to complex cases. Where additional fees/funds are not available, the CAD/CAM technique might be unprofitable, so the decision whether or not to use it remains a case-to-case decision with respect to cost versus benefit. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Electromagnetic semi-implantable hearing device: phase I. Clinical trials.

PubMed

McGee, T M; Kartush, J M; Heide, J C; Bojrab, D I; Clemis, J D; Kulick, K C

1991-04-01

Conventional hearing aids have improved significantly in recent years; however, amplification of sound within the external auditory canal creates a number of intrinsic problems, including acoustic feedback and the need for a tight ear mold to increase usable gain. Nonacoustic alternatives which could obviate these encumbrances have not become practical due to inefficient coupling (piezoelectric techniques) or unfeasible power requirements (electromagnetic techniques). Recent technical advances, however, prompted a major clinical investigation of a new electromagnetic, semi-implantable hearing device. This study presents the details of clinical phase I, in which an electromagnetic driver was coupled with a target magnet temporarily affixed onto the lateral surface of the malleus of six hearing aid users with sensorineural losses. The results indicate that the electromagnetic hearing device provides sufficient gain and output characteristics to benefit individuals with sensorineural hearing loss. Significant improvements compared to conventional hearing aids were noted in pure-tone testing and, to a lesser degree, in speech discrimination. Subjective responses were quite favorable, indicating that the electromagnetic hearing device 1. produces no acoustic feedback; 2. works well in noisy environments; and 3. provides a more quiet, natural sound than patients' conventional hearing aids. These favorable results led to phase II of the project, in which patients with surgically amendable mixed hearing losses were implanted with the target magnet incorporated within a hydroxyapatite ossicular prosthesis. The results of this second-stage investigation were also encouraging and will be reported separately.

76 FR 52734 - Underwater Locating Devices (Acoustic) (Self-Powered)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-23

...This notice announces the planned revocation of all Technical Standard Order authorizations (TSOA) issued for the production of Underwater Locating Devices (Acoustic) (Self-Powered) manufactured to the TSO-C121 and TSO-C121a specifications. These actions are necessary because the planned issuance of TSO-C121b, Underwater Locating Devices (Acoustic) (Self-Powered), with a minimum performance standard (MPS) that will increase the minimum operating life of Underwater Locating Devices from 30 days to 90 days.

77 FR 13174 - Underwater Locating Devices (Acoustic) (Self-Powered)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-05

...This is a confirmation notice for the planned revocation of all Technical Standard Order authorizations issued for the production of Underwater Locating Devices (Acoustic) (Self-Powered) manufactured to the TSO-C121 and TSO-C121a specifications. These actions are necessary because the planned issuance of TSO-C121b, Underwater Locating Devices (Acoustic) (Self-Powered), minimum performance standard (MPS) will increase the minimum operating life of Underwater Locating Devices from 30 days to 90 days.

The Teacher Aide...An Answer to the Teacher Shortage.

ERIC Educational Resources Information Center

Axford, Roger W.

The Maine State Department of Education and the Continuing Education Division of Maine State University provided a series of summer institutes in 1968 at selected university locations throughout the state for presently employed or prospective teacher aides. Courses were offered to 116 teacher aides in education and the teacher aide, classroom…

A CRITICAL REVIEW OF A PORTION OF THE LITERATURE ON TEACHING DEVICES.

ERIC Educational Resources Information Center

PORTER, DOUGLAS

A PORTION OF THE LITERATURE CONCERNING MECHANICAL TEACHING MACHINES OR DEVICES, WHICH ALLEGEDLY INCREASE THE EFFICIENCY AND EFFECTIVENESS OF TEACHING OPERATIONS BY MAKING USE OF CERTAIN PSYCHOLOGICAL PRINCIPLES AND TEACHER LABORSAVING FEATURES, IS REVIEWED. A CLASSIFICATION IS MADE OF MECHANICAL TEACHING AIDS AND DEVICES, SUGGESTING THAT THE…

Adaptive Device Context Based Mobile Learning Systems

ERIC Educational Resources Information Center

Pu, Haitao; Lin, Jinjiao; Song, Yanwei; Liu, Fasheng

2011-01-01

Mobile learning is e-learning delivered through mobile computing devices, which represents the next stage of computer-aided, multi-media based learning. Therefore, mobile learning is transforming the way of traditional education. However, as most current e-learning systems and their contents are not suitable for mobile devices, an approach for…

21 CFR 872.3730 - Pantograph.

Code of Federal Regulations, 2010 CFR

2010-04-01

... lower jaw. (b) Classification. Class I (general controls). The device is exempt from the premarket... intended to be attached to a patient's head to duplicate lower jaw movements to aid in construction of restorative and prosthetic dental devices. A marking pen is attached to the lower jaw component of the device...

Over-the-Counter Hearing Aids: A Lost Decade for Change

PubMed Central

Chan, Zoe Yee Ting; McPherson, Bradley

2015-01-01

Background. Hearing aids sold directly to consumers in retail stores or through the internet, without individual prescription by audiological professionals, are termed over-the-counter (OTC) devices. This study aimed to determine whether there was any change in the electroacoustic characteristics of OTC devices compared to research carried out a decade earlier. The previous results indicated that most OTC devices were low-frequency-emphasis devices and were unsuitable for elderly people with presbycusis, who were likely to be the major consumers of these products. Methods. Ten OTC devices were selected and their electroacoustic performance was measured. Appropriate clients for the OTC devices were derived, using four linear prescription formulae, and OTC suitability for elderly persons with presbycusis was investigated. Results. OTC electroacoustic characteristics were similar to those in the earlier study. Most OTC devices were not acoustically appropriate for potential consumers with presbycusis. Although several of the devices could match prescriptive targets for individuals with presbycusis, their poor electroacoustic performance—including ineffective volume control function, high equivalent input noise, and irregular frequency response—may override their potential benefit. Conclusion. The low-cost OTC devices were generally not suitable for the main consumers of these products, and there has been little improvement in the appropriateness of these devices over the past decade. PMID:26557701

GNSS Wristwatch Device for Networked Operations Supporting Location Based Services

DTIC Science & Technology

2008-09-01

Coordinates, Volume 4, Issue 9, Sep 2008 GNSS WRISTWATCH DEVICE FOR NETWORKED OPERATIONS SUPPORTING LOCATION BASED SERVICES Alison Brown...TITLE AND SUBTITLE GNSS Wristwatch Device for Networked Operations Supporting Location Based Services 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c...LocatorNet Portal also supports Location Based Services (LBS) based on the TIDGET solution data using an Oracle Mapping Server with an open architecture

Coil Welding Aid

NASA Technical Reports Server (NTRS)

Wiesenbach, W. T.; Clark, M. C.

1983-01-01

Positioner holds coil inside cylinder during tack welding. Welding aid spaces turns of coil inside cylinder and applies contact pressure while coil is tack-welded to cylinder. Device facilitates fabrication of heat exchangers and other structures by eliminating hand-positioning and clamping of individual coil turns.

Devices and Aids for Training M1 Tank Gunnery in the Army National Guard: A Review of Military Documents and the Research Literature.

DTIC Science & Technology

1991-04-01

U.S. DEPARTMENT OF COMMERCE NATIONAL TECHNICAL INFORMATION SERVICE SPRINGFIELD, VA 22161 D ISC, 1A13 NO TICK THIS DOCUMENT IS BEST QUALITY AVAILABLE...training strategy for use at the company level by the Army National Guard (ARNG). Six devices and aids relevant to gunnery training in an armory...M1 tank gunnery training strategy for use at home station. This report describes the results of the first phase of the project, wherein candidate

Noninvasive ultrasonic examination technology in support of counter-terrorism and drug interdiction activities: the acoustic inspection device (AID)

NASA Astrophysics Data System (ADS)

Diaz, Aaron A.; Burghard, Brion J.; Skorpik, James R.; Shepard, Chester L.; Samuel, Todd J.; Pappas, Richard A.

2003-07-01

The Pacific Northwest National Laboratory (PNNL) has developed a portable, battery-operated, handheld ultrasonic device that provides non-invasive container interrogation and material identification capabilities. The technique governing how the acoustic inspection device (AID) functions, involves measurements of ultrasonic pulses (0.1 to 5 MHz) that are launched into a container or material. The return echoes from these pulses are analyzed in terms of time-of-flight and frequency content to extract physical property measurements (the acoustic velocity and attenuation coefficient) of the material under test. The AID performs an automated analysis of the return echoes to identify the material, and detect contraband in the form of submerged packages and concealed compartments in liquid filled containers and solid-form commodities. An inspector can quickly interrogate outwardly innocuous commodity items such as shipping barrels, tanker trucks, and metal ingots. The AID can interrogate container sizes ranging from approximately 6 inches in diameter to over 96 inches in diameter and allows the inspector to sort liquid and material types into groups of like and unlike; a powerful method for discovering corrupted materials or miss-marked containers co-mingled in large shipments. This manuscript describes the functionality, capabilities and measurement methodology of the technology as it relates to homeland security applications.

Aquatics and Persons with Disabilities.

ERIC Educational Resources Information Center

Schilling, Mary Lou

1993-01-01

This bulletin shares information regarding adaptive equipment, recommended interventions, precautions, and fun activities related to aquatic activities and exercise for persons with handicapping conditions. The bulletin begins with a list of 13 safety precautions and then describes instructional aids, adaptive aids, fitness-oriented devices, and…

Visual task performance in the blind with the BrainPort V100 Vision Aid.

PubMed

Stronks, H Christiaan; Mitchell, Ellen B; Nau, Amy C; Barnes, Nick

2016-10-01

The BrainPort® V100 Vision Aid is a non-invasive assistive device for the blind based on sensory substitution. The device translates camera images into electrotactile stimuli delivered to the tongue. The BrainPort has recently received the CE mark and FDA approval and it is currently marketed to augment, rather than replace, the traditional assistive technologies such as the white cane or guide dog. Areas covered: In this work, we will review the functional studies performed to date with the BrainPort and we will highlight the critical factors that determine device performance, including the technology behind the BrainPort, the impediments to assessing device performance, and the impact of device training and rehabilitation. Expert commentary: The BrainPort enables blind people to perceive light, identify simple objects, recognize short words, localize simple objects, and detect motion and orientation of objects. To achieve this, proper rehabilitation and training regimes are crucial.

Piezoelectric translator. A simple and inexpensive device to move microelectrodes and micropipettes small distances rapidly.

PubMed

Lederer, W J

1983-09-01

A device is described that is capable of rapidly moving microelectrodes and micropipettes over distances up to 15 mu. This piezoelectric transLator uses the diaphragm from virtually any available piezoelectric buzzer in combination with simple physical support and drive electronics. All of the necessary details for the construction of this small device are presented. Each finished unit is about 2 cm long with a diameter of 2 cm and can be readily adapted to existing manipulators. The translator has been found useful in aiding the independent penetration by one or more microelectrodes of single cells or of more complicated multicellular preparations (including those that lie behind a connective tissue layer). This new device offers fine control of microelectrode motion that cannot be obtained by the other methods used to aid microelectrode and micropipette penetration of cell membranes (e.g. capacitance overcompensation--"ringing in"' or "tickling"--or tapping the manipulator base). Finally, the device described in this paper is extremely simple and inexpensive to build.

Inconsistencies in emergency instructions on common household product labels.

PubMed

Cantrell, F Lee; Nordt, Sean Patrick; Krauss, Jamey R

2013-10-01

Human exposures to non-pharmaceutical products often results in serious injury and death annually in the United States. Studies performed more than 25 years ago described inadequate first aid advice on the majority of household products. The current study evaluates contemporary non-pharmaceutical products with respect to location, uniformity and type of their first aid and emergency contact instructions. A random, convenience sample of commercial product label information was obtained from local retail stores over an 8 month period. Twelve common non-pharmaceutical product categories, with large numbers of annual human exposures, were identified from National Poison Data Systems data. A minimum of 10 unique products for each category utilized. The following information identified: product name and manufacturer, location on container, presence and type of route-specific treatment, medical assistance referral information. A total of 259 product labels were examined. First aid/contact information was located on container: rear 162 (63 %), side 28 (11 %), front 3 (1 %), bottom 2 (0.77 %), behind label 14 (5 %), missing entirely 50 (19 %). Fifty-five products (21 %) lacked any first aid instructions. Suggested contacts for accidental poisoning: none listed 75 (29 %), physician 144 (56 %), poison control centers 102 (39 %), manufacturer 44 (17 %), "Call 911" 10 (4 %). Suggested contacts for unintentional exposure and content of first aid instructions on household products were inconsistent, frequently incomplete and at times absent. Instruction locations similarly lacked uniformity. Household product labels need to provide concise, accurate first aid and emergency contact instructions in easy-to-understand language in a universal format on product labels.

Design and fabrication of a sleep apnea device using computer-aided design/additive manufacture technologies.

PubMed

Al Mortadi, Noor; Eggbeer, Dominic; Lewis, Jeffrey; Williams, Robert J

2013-04-01

The aim of this study was to analyze the latest innovations in additive manufacture techniques and uniquely apply them to dentistry, to build a sleep apnea device requiring rotating hinges. Laser scanning was used to capture the three-dimensional topography of an upper and lower dental cast. The data sets were imported into an appropriate computer-aided design software environment, which was used to design a sleep apnea device. This design was then exported as a stereolithography file and transferred for three-dimensional printing by an additive manufacture machine. The results not only revealed that the novel computer-based technique presented provides new design opportunities but also highlighted limitations that must be addressed before the techniques can become clinically viable.

Secure Location Provenance for Mobile Devices

DTIC Science & Technology

2015-07-01

SECURE LOCATION PROVENANCE FOR MOBILE DEVICES UNIVERSITY OF ALABAMA AT BIRMINGHAM JULY 2015 FINAL TECHNICAL REPORT...PROVENANCE FOR MOBILE DEVICES 5a. CONTRACT NUMBER FA8750-12-2-0254 5b. GRANT NUMBER N/A 5c. PROGRAM ELEMENT NUMBER 69220K 6. AUTHOR(S) Ragib Hasan...based services allow mobile device users to access various services based on the users’ current physical location information. Path-critical applications

Handheld Technology Acceptance in Radiologic Science Education and Training Programs

ERIC Educational Resources Information Center

Powers, Kevin Jay

2012-01-01

The purpose of this study was to explore the behavioral intention of directors of educational programs in the radiologic sciences to adopt handheld devices to aid in managing student clinical data. Handheld devices were described to participants as a technology representing a class of mobile electronic devices including, but not limited to,…

Management of overdenture abutments health by an innovative cleaning aid

PubMed Central

Mall, Priyanka; Singh, Kamleshwar; Singh, Saumyendra Vikram; Agrawal, Kaushal Kishor; Siddharth, Ramashanker; Chand, Pooran

2012-01-01

This article describes a method for fabrication of a custom-made device for cleaning dome-shaped overdenture abutments. A kid toothbrush and a rubber cup were used for fabrication of a prophylactic device. After regular use of this device periodontal health status of the overdenture abutments patients improved satisfactorily. PMID:23230248

Mobility Device Quality Affects Participation Outcomes for People With Disabilities: A Structural Equation Modeling Analysis.

PubMed

Magasi, Susan; Wong, Alex; Miskovic, Ana; Tulsky, David; Heinemann, Allen W

2018-01-01

To test the effect that indicators of mobility device quality have on participation outcomes in community-dwelling adults with spinal cord injury, traumatic brain injury, and stroke by using structural equation modeling. Survey, cross-sectional study, and model testing. Clinical research space at 2 academic medical centers and 1 free-standing rehabilitation hospital. Community-dwelling adults (N=250; mean age, 48±14.3y) with spinal cord injury, traumatic brain injury, and stroke. Not applicable. The Mobility Device Impact Scale, Patient-Reported Outcomes Measurement Information System Social Function (version 2.0) scale, including Ability to Participate in Social Roles and Activities and Satisfaction with Social Roles and Activities, and the 2 Community Participation Indicators' enfranchisement scales. Details about device quality (reparability, reliability, ease of maintenance) and device type were also collected. Respondents used ambulation aids (30%), manual (34%), and power wheelchairs (30%). Indicators of device quality had a moderating effect on participation outcomes, with 3 device quality variables (repairability, ease of maintenance, device reliability) accounting for 20% of the variance in participation. Wheelchair users reported lower participation enfranchisement than did ambulation aid users. Mobility device quality plays an important role in participation outcomes. It is critical that people have access to mobility devices and that these devices be reliable. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

The Role of Color Cues in Facilitating Accurate and Rapid Location of Aided Symbols by Children with and without Down Syndrome

ERIC Educational Resources Information Center

Wilkinson, Krista; Carlin, Michael; Thistle, Jennifer

2008-01-01

Purpose: This research examined how the color distribution of symbols within a visual aided augmentative and alternative communication array influenced the speed and accuracy with which participants with and without Down syndrome located a target picture symbol. Method: Eight typically developing children below the age of 4 years, 8 typically…

Effectiveness of portable electronic and optical magnifiers for near vision activities in low vision: a randomised crossover trial.

PubMed

Taylor, John J; Bambrick, Rachel; Brand, Andrew; Bray, Nathan; Dutton, Michelle; Harper, Robert A; Hoare, Zoe; Ryan, Barbara; Edwards, Rhiannon T; Waterman, Heather; Dickinson, Christine

2017-07-01

To compare the performance of near vision activities using additional portable electronic vision enhancement systems (p-EVES), to using optical magnifiers alone, by individuals with visual impairment. A total of 100 experienced optical aid users were recruited from low vision clinics at Manchester Royal Eye Hospital, Manchester, UK, to a prospective two-arm cross-over randomised controlled trial. Reading, performance of near vision activities, and device usage were evaluated at baseline; and at the end of each study arm (Intervention A: existing optical aids plus p-EVES; Intervention B: optical aids only) which was after 2 and 4 months. A total of 82 participants completed the study. Overall, maximum reading speed for high contrast sentences was not statistically significantly different for optical aids and p-EVES, although the critical print size and threshold print size which could be accessed with p-EVES were statistically significantly smaller (p < 0.001 in both cases). The optical aids were used for a larger number of tasks (p < 0.001), and used more frequently (p < 0.001). However p-EVES were preferred for leisure reading by 70% of participants, and allowed longer duration of reading (p < 0.001). During the study arm when they had a p-EVES device, participants were able to carry out more tasks independently (p < 0.001), and reported less difficulty with a range of near vision activities (p < 0.001). The study provides evidence that p-EVES devices can play a useful role in supplementing the range of low vision aids used to reduce activity limitation for near vision tasks. © 2017 The Authors Ophthalmic & Physiological Optics © 2017 The College of Optometrists.

The Master Hearing Aid

PubMed Central

Curran, James R.

2013-01-01

As early as the 1930s the term Master Hearing Aid (MHA) described a device used in the fitting of hearing aids. In their original form, the MHA was a desktop system that allowed for simulated or actual adjustment of hearing aid components that resulted in a changed hearing aid response. Over the years the MHA saw many embodiments and contributed to a number of rationales for the fitting of hearing aids. During these same years, the MHA was viewed by many as an inappropriate means of demonstrating hearing aids; the audio quality of the desktop systems was often superior to the hearing aids themselves. These opinions and the evolution of the MHA have molded the modern perception of hearing aids and the techniques used in the fitting of hearing aids. This article reports on a history of the MHA and its influence on the fitting of hearing aids. PMID:23686682

Assistive Listening Devices: A Report of the National Task Force on Quality of Services in the Postsecondary Education of Deaf and Hard of Hearing Students.

ERIC Educational Resources Information Center

Warick, Ruth; Clark, Catherine; Dancer, Jesse; Sinclair, Stephen

This report examines the use of auditory assistive listening devices by students who are hard of hearing or deaf in the postsecondary educational setting. Individual sections address the following topics: (1) distinctions between hearing aids and assistive listening devices; (2) assistive listening devices and the college student; (3) types of…

Hearing Aids and Personal Sound Amplifiers: Know the Difference

MedlinePlus

... Devices and Personal Sound Amplification Products - Guidance for Industry and FDA Staff (PDF - 42KB) More in Consumer Updates Animal & Veterinary Children's Health Cosmetics Dietary Supplements Drugs Food Medical Devices Nutrition Radiation-Emitting Products Tobacco Products ...

Effects of venting on wind noise levels measured at the eardrum.

PubMed

Chung, King

2013-01-01

Wind noise can be a nuisance to hearing aid users. With the advent of sophisticated feedback reduction algorithms, people with higher degrees of hearing loss are fit with larger vents than previously allowed, and more people with lesser degrees of hearing loss are fit with open hearing aids. The purpose of this study was to examine the effects of venting on wind noise levels in the ear canal for hearing aids with omnidirectional and directional microphones. Two behind-the-ear hearing aids were programmed when they were worn on a Knowles Electronics Manikin for Acoustic Research. The hearing aid worn on the right ear was programmed to the omnidirectional microphone mode and the one on the left to the directional microphone mode. The hearing aids were adjusted to linear amplification with flat frequency response in an anechoic chamber. Gains below 10 dB were used to avoid output limiting of wind noise levels at low input levels. Wind noise samples were recorded at the eardrum location in a wind tunnel at wind velocities ranging from a gentle to a strong breeze. The hearing aids were coupled to #13 tubings (i.e., open vent), or conventional skeleton earmolds with no vent, pressure vents, or 3mm vents. Polar and spectral characteristics of wind noise were analyzed off-line using MatLab programs. Wind noise levels in the ear canals were mostly predicted by vent-induced frequency response changes in the conventional earmold conditions for both omnidirectional and directional hearing aids. The open vent condition, however, yielded the lowest levels, which could not be entirely predicted by the frequency response changes of the hearing aids. This indicated that a wind-related vent effect permitted an additional amount of sound reduction in the ear canal, which could not be explained by known vent effects. For the microphone location, form factor, and gain settings tested, open fit hearing aids yielded lower noise levels at the eardrum location than conventional behind-the-ear hearing aids.

Resistive switching characteristics and mechanisms in silicon oxide memory devices

NASA Astrophysics Data System (ADS)

Chang, Yao-Feng; Fowler, Burt; Chen, Ying-Chen; Zhou, Fei; Wu, Xiaohan; Chen, Yen-Ting; Wang, Yanzhen; Xue, Fei; Lee, Jack C.

2016-05-01

Intrinsic unipolar SiOx-based resistance random access memories (ReRAM) characterization, switching mechanisms, and applications have been investigated. Device structures, material compositions, and electrical characteristics are identified that enable ReRAM cells with high ON/OFF ratio, low static power consumption, low switching power, and high readout-margin using complementary metal-oxide semiconductor transistor (CMOS)-compatible SiOx-based materials. These ideas are combined with the use of horizontal and vertical device structure designs, composition optimization, electrical control, and external factors to help understand resistive switching (RS) mechanisms. Measured temperature effects, pulse response, and carrier transport behaviors lead to compact models of RS mechanisms and energy band diagrams in order to aid the development of computer-aided design for ultralarge-v scale integration. This chapter presents a comprehensive investigation of SiOx-based RS characteristics and mechanisms for the post-CMOS device era.

Falls and Use of Assistive Devices in Stroke Patients with Hemiparesis: Association with Balance Ability and Fall Efficacy.

PubMed

Kim, Oksoo; Kim, Jung-Hee

2015-01-01

This study investigates balance ability and the fall efficacy with regard to the experiences of stroke patients with hemiparesis. The experience of falling, the use of assistive devices, and each disease-related characteristic were assessed using face-to-face interviews and a self-reported questionnaire. The Berg Balance Scale and Fall Efficacy Scale were used to measure balance ability and confidence. The fall efficacy was significantly lower in participants who had experienced falls than those who had not. The participants who used assistive devices exhibited low balance ability and fall efficacy compared to those who did not use assistive devices. Stroke patients with fall experience and walking aids might be considered at increased risk of falling. Preventive measures for individuals using walking aids may be beneficial in reducing the fall rate of community-dwelling stroke patients. © 2014 Association of Rehabilitation Nurses.

Computer-aided design and experimental investigation of a hydrodynamic device: the microwire electrode

PubMed

Fulian; Gooch; Fisher; Stevens; Compton

2000-08-01

The development and application of a new electrochemical device using a computer-aided design strategy is reported. This novel design is based on the flow of electrolyte solution past a microwire electrode situated centrally within a large duct. In the design stage, finite element simulations were employed to evaluate feasible working geometries and mass transport rates. The computer-optimized designs were then exploited to construct experimental devices. Steady-state voltammetric measurements were performed for a reversible one-electron-transfer reaction to establish the experimental relationship between electrolysis current and solution velocity. The experimental results are compared to those predicted numerically, and good agreement is found. The numerical studies are also used to establish an empirical relationship between the mass transport limited current and the volume flow rate, providing a simple and quantitative alternative for workers who would prefer to exploit this device without the need to develop the numerical aspects.

46 CFR 199.178 - Marking of stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Marking of stowage locations. 199.178 Section 199.178... locations. (a) Containers, brackets, racks, and other similar stowage locations for lifesaving equipment... that location. (b) If more than one device is stowed in a location, the number of devices stowed must...

Measurements and TCAD simulation of novel ATLAS planar pixel detector structures for the HL-LHC upgrade

NASA Astrophysics Data System (ADS)

Nellist, C.; Dinu, N.; Gkougkousis, E.; Lounis, A.

2015-06-01

The LHC accelerator complex will be upgraded between 2020-2022, to the High-Luminosity-LHC, to considerably increase statistics for the various physics analyses. To operate under these challenging new conditions, and maintain excellent performance in track reconstruction and vertex location, the ATLAS pixel detector must be substantially upgraded and a full replacement is expected. Processing techniques for novel pixel designs are optimised through characterisation of test structures in a clean room and also through simulations with Technology Computer Aided Design (TCAD). A method to study non-perpendicular tracks through a pixel device is discussed. Comparison of TCAD simulations with Secondary Ion Mass Spectrometry (SIMS) measurements to investigate the doping profile of structures and validate the simulation process is also presented.

Observation of Critical-Gradient Behavior in Alfvén-Eigenmode-Induced Fast-Ion Transport.

PubMed

Collins, C S; Heidbrink, W W; Austin, M E; Kramer, G J; Pace, D C; Petty, C C; Stagner, L; Van Zeeland, M A; White, R B; Zhu, Y B

2016-03-04

Experiments in the DIII-D tokamak show that fast-ion transport suddenly becomes stiff above a critical threshold in the presence of many overlapping small-amplitude Alfvén eigenmodes (AEs). The threshold is phase-space dependent and occurs when particle orbits become stochastic due to resonances with AEs. Above threshold, equilibrium fast-ion density profiles are unchanged despite increased drive, and intermittent fast-ion losses are observed. Fast-ion Dα spectroscopy indicates radially localized transport of the copassing population at radii that correspond to the location of midcore AEs. The observation of stiff fast-ion transport suggests that reduced models can be used to effectively predict alpha profiles, beam ion profiles, and losses to aid in the design of optimized scenarios for future burning plasma devices.

Portable imaging system method and apparatus

DOEpatents

Freifeld, Barry M.; Kneafsley, Timothy J.; Pruess, Jacob; Tomutsa, Liviu; Reiter, Paul A.; deCastro, Ted M.

2006-07-25

An operator shielded X-ray imaging system has sufficiently low mass (less than 300 kg) and is compact enough to enable portability by reducing operator shielding requirements to a minimum shielded volume. The resultant shielded volume may require a relatively small mass of shielding in addition to the already integrally shielded X-ray source, intensifier, and detector. The system is suitable for portable imaging of well cores at remotely located well drilling sites. The system accommodates either small samples, or small cross-sectioned objects of unlimited length. By rotating samples relative to the imaging device, the information required for computer aided tomographic reconstruction may be obtained. By further translating the samples relative to the imaging system, fully three dimensional (3D) tomographic reconstructions may be obtained of samples having arbitrary length.

46 CFR 108.646 - Marking of stowage locations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN... with symbols in accordance with IMO Resolution A.760(18), indicating the devices stowed in that location for that purpose. (b) If more than one device is stowed in that location, the number of devices...

Electronic Travel Aids for Blind Persons.

ERIC Educational Resources Information Center

Hill, Everett W.; Bradfield, Anna L.

1984-01-01

The article describes application for visually impaired persons of widely used Electronic Travel Aids--the Lindsay Russell Pathsounder, the Mowat Sensor, the Sonicguide, and the C-5 Laser Cane. In addition, a research review provides insight into the issues affecting future use of the devices. (Author/CL)

Communication Aids in Special Education.

ERIC Educational Resources Information Center

Education Turnkey Systems, Inc., Falls Church, VA.

One of four reports designed to assess the current state of new technologies, the document reviews the current status of technologically oriented communication aids for the handicapped. Explained are such technological aspects as the characteristics of electronically based devices which permit special students to have access to technological…

23 CFR 655.607 - Funding.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 23 Highways 1 2013-04-01 2013-04-01 false Funding. 655.607 Section 655.607 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS TRAFFIC OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.607 Funding. (a) Federal-aid...

23 CFR 655.607 - Funding.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 23 Highways 1 2014-04-01 2014-04-01 false Funding. 655.607 Section 655.607 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS TRAFFIC OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.607 Funding. (a) Federal-aid...

23 CFR 655.607 - Funding.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 23 Highways 1 2011-04-01 2011-04-01 false Funding. 655.607 Section 655.607 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS TRAFFIC OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.607 Funding. (a) Federal-aid...

23 CFR 655.607 - Funding.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 23 Highways 1 2012-04-01 2012-04-01 false Funding. 655.607 Section 655.607 Highways FEDERAL HIGHWAY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION ENGINEERING AND TRAFFIC OPERATIONS TRAFFIC OPERATIONS Traffic Control Devices on Federal-Aid and Other Streets and Highways § 655.607 Funding. (a) Federal-aid...

Utilising three-dimensional printing techniques when providing unique assistive devices: A case report.

PubMed

Day, Sarah Jane; Riley, Shaun Patrick

2018-02-01

The evolution of three-dimensional printing into prosthetics has opened conversations about the availability and cost of prostheses. This report will discuss how a prosthetic team incorporated additive manufacture techniques into the treatment of a patient with a partial hand amputation to create and test a unique assistive device which he could use to hold his French horn. Case description and methods: Using a process of shape capture, photogrammetry, computer-aided design and finite element analysis, a suitable assistive device was designed and tested. The design was fabricated using three-dimensional printing. Patient satisfaction was measured using a Pugh's Matrix™, and a cost comparison was made between the process used and traditional manufacturing. Findings and outcomes: Patient satisfaction was high. The three-dimensional printed devices were 56% cheaper to fabricate than a similar laminated device. Computer-aided design and three-dimensional printing proved to be an effective method for designing, testing and fabricating a unique assistive device. Clinical relevance CAD and 3D printing techniques can enable devices to be designed, tested and fabricated cheaper than when using traditional techniques. This may lead to improvements in quality and accessibility.

Performances of different global positioning system devices for time-location tracking in air pollution epidemiological studies.

PubMed

Wu, Jun; Jiang, Chengsheng; Liu, Zhen; Houston, Douglas; Jaimes, Guillermo; McConnell, Rob

2010-11-23

People's time-location patterns are important in air pollution exposure assessment because pollution levels may vary considerably by location. A growing number of studies are using global positioning systems (GPS) to track people's time-location patterns. Many portable GPS units that archive location are commercially available at a cost that makes their use feasible for epidemiological studies. We evaluated the performance of five portable GPS data loggers and two GPS cell phones by examining positional accuracy in typical locations (indoor, outdoor, in-vehicle) and factors that influence satellite reception (building material, building type), acquisition time (cold and warm start), battery life, and adequacy of memory for data storage. We examined stationary locations (eg, indoor, outdoor) and mobile environments (eg, walking, traveling by vehicle or bus) and compared GPS locations to highly-resolved US Geological Survey (USGS) and Digital Orthophoto Quarter Quadrangle (DOQQ) maps. The battery life of our tested instruments ranged from <9 hours to 48 hours. The acquisition of location time after startup ranged from a few seconds to >20 minutes and varied significantly by building structure type and by cold or warm start. No GPS device was found to have consistently superior performance with regard to spatial accuracy and signal loss. At fixed outdoor locations, 65%-95% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices. At fixed indoor locations, 50%-80% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices except one. Most of the GPS devices performed well during commuting on a freeway, with >80% of points within 10-m of the DOQQ route, but the performance was significantly impacted by surrounding structures on surface streets in highly urbanized areas. All the tested GPS devices had limitations, but we identified several devices which showed promising performance for tracking subjects' time location patterns in epidemiological studies.

Performances of Different Global Positioning System Devices for Time-Location Tracking in Air Pollution Epidemiological Studies

PubMed Central

Wu, Jun; Jiang, Chengsheng; Liu, Zhen; Houston, Douglas; Jaimes, Guillermo; McConnell, Rob

2010-01-01

Background: People’s time-location patterns are important in air pollution exposure assessment because pollution levels may vary considerably by location. A growing number of studies are using global positioning systems (GPS) to track people’s time-location patterns. Many portable GPS units that archive location are commercially available at a cost that makes their use feasible for epidemiological studies. Methods: We evaluated the performance of five portable GPS data loggers and two GPS cell phones by examining positional accuracy in typical locations (indoor, outdoor, in-vehicle) and factors that influence satellite reception (building material, building type), acquisition time (cold and warm start), battery life, and adequacy of memory for data storage. We examined stationary locations (eg, indoor, outdoor) and mobile environments (eg, walking, traveling by vehicle or bus) and compared GPS locations to highly-resolved US Geological Survey (USGS) and Digital Orthophoto Quarter Quadrangle (DOQQ) maps. Results: The battery life of our tested instruments ranged from <9 hours to 48 hours. The acquisition of location time after startup ranged from a few seconds to >20 minutes and varied significantly by building structure type and by cold or warm start. No GPS device was found to have consistently superior performance with regard to spatial accuracy and signal loss. At fixed outdoor locations, 65%–95% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices. At fixed indoor locations, 50%–80% of GPS points fell within 20-m of the corresponding DOQQ locations for all the devices except one. Most of the GPS devices performed well during commuting on a freeway, with >80% of points within 10-m of the DOQQ route, but the performance was significantly impacted by surrounding structures on surface streets in highly urbanized areas. Conclusions: All the tested GPS devices had limitations, but we identified several devices which showed promising performance for tracking subjects’ time location patterns in epidemiological studies. PMID:21151593

Patient Preferences for Device-Aided Treatments Indicated for Advanced Parkinson Disease.

PubMed

Marshall, Thomas; Pugh, Amy; Fairchild, Angelyn; Hass, Steven

2017-12-01

Effective treatment for advanced Parkinson disease (PD) uncontrolled with oral medication includes device-aided therapies such as deep brain stimulation (DBS) and continuous levodopa-carbidopa infusion to the duodenum via a portable pump. Our objective was to quantify patient preferences for attributes of these device-aided treatments. We administered a Web-enabled survey to 401 patients in the United States. A discrete-choice experiment (DCE) was used to evaluate patients' willingness to accept tradeoffs among efficacy, tolerability, and convenience of alternative treatments. DCE data were analyzed using random-parameters logit. Best-worst scaling (BWS) was used to elicit the relative importance of device-specific attributes. Conditional logit was used to analyze the BWS data. We tested for differences in preferences among subgroups of patients. Improving ability to think clearly was twice as important as a 6-hour-per-day improvement in control of movement symptoms. After controlling for efficacy, treatment delivered via portable infusion pump was preferred over DBS, and both devices were preferred to oral therapy with poor symptom control. Patients were most concerned about device attributes relating to risk of stroke, difficulty thinking, and neurosurgery. Avoiding surgery to insert a wire in the brain was more important than avoiding surgery to insert a tube into the small intestine. Some differences in preferences among subgroups were statistically, but not qualitatively, significant. This study clarifies the patient perspective in therapeutic choices for advanced PD. These findings may help improve communication between patients and providers and also provide evidence on patient preferences to inform regulatory and access decisions. Copyright © 2017. Published by Elsevier Inc.

Evolution of design considerations in complex craniofacial reconstruction using patient-specific implants.

PubMed

Peel, Sean; Bhatia, Satyajeet; Eggbeer, Dominic; Morris, Daniel S; Hayhurst, Caroline

2017-06-01

Previously published evidence has established major clinical benefits from using computer-aided design, computer-aided manufacturing, and additive manufacturing to produce patient-specific devices. These include cutting guides, drilling guides, positioning guides, and implants. However, custom devices produced using these methods are still not in routine use, particularly by the UK National Health Service. Oft-cited reasons for this slow uptake include the following: a higher up-front cost than conventionally fabricated devices, material-choice uncertainty, and a lack of long-term follow-up due to their relatively recent introduction. This article identifies a further gap in current knowledge - that of design rules, or key specification considerations for complex computer-aided design/computer-aided manufacturing/additive manufacturing devices. This research begins to address the gap by combining a detailed review of the literature with first-hand experience of interdisciplinary collaboration on five craniofacial patient case studies. In each patient case, bony lesions in the orbito-temporal region were segmented, excised, and reconstructed in the virtual environment. Three cases translated these digital plans into theatre via polymer surgical guides. Four cases utilised additive manufacturing to fabricate titanium implants. One implant was machined from polyether ether ketone. From the literature, articles with relevant abstracts were analysed to extract design considerations. In all, 19 frequently recurring design considerations were extracted from previous publications. Nine new design considerations were extracted from the case studies - on the basis of subjective clinical evaluation. These were synthesised to produce a design considerations framework to assist clinicians with prescribing and design engineers with modelling. Promising avenues for further research are proposed.

Spinoff 2009

NASA Technical Reports Server (NTRS)

2009-01-01

Topics covered include: Image-Capture Devices Extend Medicine's Reach; Medical Devices Assess, Treat Balance Disorders; NASA Bioreactors Advance Disease Treatments; Robotics Algorithms Provide Nutritional Guidelines; "Anti-Gravity" Treadmills Speed Rehabilitation; Crew Management Processes Revitalize Patient Care; Hubble Systems Optimize Hospital Schedules; Web-based Programs Assess Cognitive Fitness; Electrolyte Concentrates Treat Dehydration; Tools Lighten Designs, Maintain Structural Integrity; Insulating Foams Save Money, Increase Safety; Polyimide Resins Resist Extreme Temperatures; Sensors Locate Radio Interference; Surface Operations Systems Improve Airport Efficiency; Nontoxic Resins Advance Aerospace Manufacturing; Sensors Provide Early Warning of Biological Threats; Robot Saves Soldier's Lives Overseas (MarcBot); Apollo-Era Life Raft Saves Hundreds of Sailors; Circuits Enhance Scientific Instruments and Safety Devices; Tough Textiles Protect Payloads and Public Safety Officers; Forecasting Tools Point to Fishing Hotspots; Air Purifiers Eliminate Pathogens, Preserve Food; Fabrics Protect Sensitive Skin from UV Rays; Phase Change Fabrics Control Temperature; Tiny Devices Project Sharp, Colorful Images; Star-Mapping Tools Enable Tracking of Endangered Animals; Nanofiber Filters Eliminate Contaminants; Modeling Innovations Advance Wind Energy Industry; Thermal Insulation Strips Conserve Energy; Satellite Respondent Buoys Identify Ocean Debris; Mobile Instruments Measure Atmospheric Pollutants; Cloud Imagers Offer New Details on Earth's Health; Antennas Lower Cost of Satellite Access; Feature Detection Systems Enhance Satellite Imagery; Chlorophyll Meters Aid Plant Nutrient Management; Telemetry Boards Interpret Rocket, Airplane Engine Data; Programs Automate Complex Operations Monitoring; Software Tools Streamline Project Management; Modeling Languages Refine Vehicle Design; Radio Relays Improve Wireless Products; Advanced Sensors Boost Optical Communication, Imaging; Tensile Fabrics Enhance Architecture Around the World; Robust Light Filters Support Powerful Imaging Devices; Thermoelectric Devices Cool, Power Electronics; Innovative Tools Advance Revolutionary Weld Technique; Methods Reduce Cost, Enhance Quality of Nanotubes; Gauging Systems Monitor Cryogenic Liquids; Voltage Sensors Monitor Harmful Static; and Compact Instruments Measure Heat Potential.

Analysis of electrical characteristics and proposal of design guide for ultra-scaled nanoplate vertical FET and 6T-SRAM

NASA Astrophysics Data System (ADS)

Seo, Youngsoo; Kim, Shinkeun; Ko, Kyul; Woo, Changbeom; Kim, Minsoo; Lee, Jangkyu; Kang, Myounggon; Shin, Hyungcheol

2018-02-01

In this paper, electrical characteristics of gate-all-around (GAA) nanoplate (NP) vertical FET (VFET) were analyzed for single transistor and 6T-SRAM cell through 3D technology computer-aided design (TCAD) simulation. In VFET, gate and extension lengths are not limited by the area of device because theses lengths are vertically located. The height of NP is assumed in 40 nm considering device fabrication method (top-down approach). According to the sizes of devices, we analyzed the performances of device such as total resistance, capacitance, intrinsic gate delay, sub-threshold swing (S.S), drain-induced barrier lowering (DIBL) and static noise margin (SNM). As the gate length becomes larger, the resistance should be smaller because the total height of NP is fixed in 40 nm. Also, when the channel thickness becomes thicker, the total resistance becomes smaller since the sheet resistances of channel and extension become smaller and the contact resistance becomes smaller due to the increasing contact area. In addition, as the length of channel pitch increases, the parasitic capacitance comes to be larger due to the increasing area of gate-drain and gate-source. The performance of RC delay is best in the shortest gate length (12 nm), the thickest channel (6 nm) and the shortest channel pitch (17 nm) owing to the reduced resistance and parasitic capacitance. However, the other performances such as DIBL, S.S, on/off ratio and SNM are worst because the short channel effect is highest in this situation. Also, we investigated the performance of the multi-channel device. As the number of channels increases, the performance of device and the reliability of SRAM improve because of reduced contact resistance, increased gate dimension and multi-channel compensation effect.

Uses of the Sonicguide as a Concept Development Device.

ERIC Educational Resources Information Center

Vopata, Alvin E.

1978-01-01

The article discusses the Sonicguide, and electronic mobility device for the blind, and makes some suggestions for its introduction to young children and for its use as an aid in the development of spatial concepts. (Author/DLS)

21 CFR 876.5090 - Suprapubic urological catheter and accessories.

Code of Federal Regulations, 2010 CFR

2010-04-01

... accessories is a flexible tubular device that is inserted through the abdominal wall into the urinary bladder with the aid of a trocar and cannula. The device is used to pass fluids to and from the urinary tract...

Assessment of Cardiac Device Position on Supine Chest Radiograph in the ICU: Introduction and Applicability of the Aortic Valve Location Ratio.

PubMed

Ouweneel, Dagmar M; Sjauw, Krischan D; Wiegerinck, Esther M A; Hirsch, Alexander; Baan, Jan; de Mol, Bas A J M; Lagrand, Wim K; Planken, R Nils; Henriques, José P S

2016-10-01

The use of intracardiac assist devices is expanding, and correct position of these devices is required for optimal functioning. The aortic valve is an important landmark for positioning of those devices. It would be of great value if the device position could be easily monitored on plain supine chest radiograph in the ICU. We introduce a ratio-based tool for determination of the aortic valve location on plain supine chest radiograph images, which can be used to evaluate intracardiac device position. Retrospective observational study. Large academic medical center. Patients admitted to the ICU and supported by an intracardiac assist device. We developed a ratio to determine the aortic valve location on supine chest radiograph images. This ratio is used to assess the position of a cardiac assist device and is compared with echocardiographic findings. Supine anterior-posterior chest radiographs of patients with an aortic valve prosthesis (n = 473) were analyzed to determine the location of the aortic valve. We calculated several ratios with the potential to determine the position of the aortic valve. The aortic valve location ratio, defined as the distance between the carina and the aortic valve, divided by the thoracic width, was found to be the best performing ratio. The aortic valve location ratio determines the location of the aortic valve caudal to the carina, at a distance of 0.25 ± 0.05 times the thoracic width for male patients and 0.28 ± 0.05 times the thoracic width for female patients. The aortic valve location ratio was validated using CT images of patients with angina pectoris without known valvular disease (n = 95). There was a good correlation between cardiac device position (Impella) assessed with the aortic valve location ratio and with echocardiography (n = 53). The aortic valve location ratio enables accurate and reproducible localization of the aortic valve on supine chest radiograph. This tool is easily applicable and can be used for assessment of cardiac device position in patients on the ICU.

Fun During Knee Rehabilitation: Feasibility and Acceptability Testing of a New Android-Based Training Device.

PubMed

Weber-Spickschen, Thomas Sanjay; Colcuc, Christian; Hanke, Alexander; Clausen, Jan-Dierk; James, Paul Abraham; Horstmann, Hauke

2017-01-01

The initial goals of rehabilitation after knee injuries and operations are to achieve full knee extension and to activate quadriceps muscle. In addition to regular physiotherapy, an android-based knee training device is designed to help patients achieve these goals and improve compliance in the early rehabilitation period. This knee training device combines fun in a computer game with muscular training or rehabilitation. Our aim was to test the feasibility and acceptability of this new device. 50 volunteered subjects enrolled to test out the computer game aided device. The first game was the high-striker game, which recorded maximum knee extension power. The second game involved controlling quadriceps muscular power to simulate flying an aeroplane in order to record accuracy of muscle activation. The subjects evaluated this game by completing a simple questionnaire. No technical problem was encountered during the usage of this device. No subjects complained of any discomfort after using this device. Measurements including maximum knee extension power, knee muscle activation and control were recorded successfully. Subjects rated their experience with the device as either excellent or very good and agreed that the device can motivate and monitor the progress of knee rehabilitation training. To the best of our knowledge, this is the first android-based tool available to fast track knee rehabilitation training. All subjects gave very positive feedback to this computer game aided knee device.

Financial Aid.

ERIC Educational Resources Information Center

Graves, Mary A.

This workbook assists college and vocational school bound American Indian students in determining their financial needs and in locating sources of financial aid. A checklist helps students assess the state of their knowledge of financial programs; a glossary defines terms pertinent to the realm of financial aid (i.e., graduate study programs,…

Herbst appliance in lingual orthodontics.

PubMed

Wiechmann, Dirk; Schwestka-Polly, Rainer; Hohoff, Ariane

2008-09-01

The aims of this article were to outline a technique for attaching Herbst telescopes to a customized lingual orthodontic (LO) appliance and to demonstrate the treatment phases and outcome with a case report. The interface between the LO appliance and the telescopes consists of a computer-aided design/computer-aided manufacturing (CAD/CAM), custom-made labial pivot base connected to the custom-made bands of the maxillary molars and mandibular canines. The individual CAD depiction of the interface ensures an optimal 3-dimensional tube-and-plunger position for correct and smooth function of the telescope mechanism. Because of the lingual location of the brackets, a small buccal tooth-to-telescope distance can be achieved, increasing patient comfort. Various options of anchorage are possible with only 1 device. After bite jumping, the telescopes and pivot bases can be removed easily without debonding the bands or removing the archwires. Experience from the first patient suggests that the Herbst-LO appliance facilitates treatment control during all phases, decreases the risk of interface breakage and mandibular incisor flaring, and might reduce overall treatment time. These initial clinical observations justify further research to provide evidence about the efficacy of Herbst-LO appliances.

Lithium cell tests at Marshall Space Flight Center. [batteries for range safety and frustrum location aid in the shuttle solid rocket booster

NASA Technical Reports Server (NTRS)

Paschal, L. E.

1977-01-01

Three 18 AH Li-CF batteries with a polypropylene separator and using dimethyl sulfite in Li as F6 for the electrolyte will be placed in each shuttle solid rocket booster for range safety and frustrum location aid. Mechanical vibration, acceleration, random and design vibration, and discharge evaluation tests are discussed.

33 CFR 164.40 - Devices to indicate speed and distance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Devices to indicate speed and... speed and distance. (a) Each vessel required to be fitted with an Automatic Radar Plotting Aid (ARPA) under § 164.38 of this part must be fitted with a device to indicate speed and distance of the vessel...

33 CFR 164.40 - Devices to indicate speed and distance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Devices to indicate speed and... speed and distance. (a) Each vessel required to be fitted with an Automatic Radar Plotting Aid (ARPA) under § 164.38 of this part must be fitted with a device to indicate speed and distance of the vessel...

Implantable Heart Aid

NASA Technical Reports Server (NTRS)

1980-01-01

Medrad utilized NASA's Apollo technology to develop a new device called the AID implantable automatic pulse generator which monitors the heart continuously, recognizes the onset of ventricular fibrillation and delivers a corrective electrical shock. AID pulse generator is, in effect, a miniaturized version of the defibrillator used by emergency squads and hospitals to restore rhythmic heartbeat after fibrillation, but has the unique advantage of being permanently available to the patient at risk. Once implanted, it needs no specially trained personnel or additional equipment. AID system consists of a microcomputer, a power source and two electrodes which sense heart activity.

Development of a computer program data base of a navigation aid environment for simulated IFR flight and landing studies

NASA Technical Reports Server (NTRS)

Bergeron, H. P.; Haynie, A. T.; Mcdede, J. B.

1980-01-01

A general aviation single pilot instrument flight rule simulation capability was developed. Problems experienced by single pilots flying in IFR conditions were investigated. The simulation required a three dimensional spatial navaid environment of a flight navigational area. A computer simulation of all the navigational aids plus 12 selected airports located in the Washington/Norfolk area was developed. All programmed locations in the list were referenced to a Cartesian coordinate system with the origin located at a specified airport's reference point. All navigational aids with their associated frequencies, call letters, locations, and orientations plus runways and true headings are included in the data base. The simulation included a TV displayed out-the-window visual scene of country and suburban terrain and a scaled model runway complex. Any of the programmed runways, with all its associated navaids, can be referenced to a runway on the airport in this visual scene. This allows a simulation of a full mission scenario including breakout and landing.

Smartphone-Based System for Learning and Inferring Hearing Aid Settings.

PubMed

Aldaz, Gabriel; Puria, Sunil; Leifer, Larry J

2016-10-01

Previous research has shown that hearing aid wearers can successfully self-train their instruments' gain-frequency response and compression parameters in everyday situations. Combining hearing aids with a smartphone introduces additional computing power, memory, and a graphical user interface that may enable greater setting personalization. To explore the benefits of self-training with a smartphone-based hearing system, a parameter space was chosen with four possible combinations of microphone mode (omnidirectional and directional) and noise reduction state (active and off). The baseline for comparison was the "untrained system," that is, the manufacturer's algorithm for automatically selecting microphone mode and noise reduction state based on acoustic environment. The "trained system" first learned each individual's preferences, self-entered via a smartphone in real-world situations, to build a trained model. The system then predicted the optimal setting (among available choices) using an inference engine, which considered the trained model and current context (e.g., sound environment, location, and time). To develop a smartphone-based prototype hearing system that can be trained to learn preferred user settings. Determine whether user study participants showed a preference for trained over untrained system settings. An experimental within-participants study. Participants used a prototype hearing system-comprising two hearing aids, Android smartphone, and body-worn gateway device-for ∼6 weeks. Sixteen adults with mild-to-moderate sensorineural hearing loss (HL) (ten males, six females; mean age = 55.5 yr). Fifteen had ≥6 mo of experience wearing hearing aids, and 14 had previous experience using smartphones. Participants were fitted and instructed to perform daily comparisons of settings ("listening evaluations") through a smartphone-based software application called Hearing Aid Learning and Inference Controller (HALIC). In the four-week-long training phase, HALIC recorded individual listening preferences along with sensor data from the smartphone-including environmental sound classification, sound level, and location-to build trained models. In the subsequent two-week-long validation phase, participants performed blinded listening evaluations comparing settings predicted by the trained system ("trained settings") to those suggested by the hearing aids' untrained system ("untrained settings"). We analyzed data collected on the smartphone and hearing aids during the study. We also obtained audiometric and demographic information. Overall, the 15 participants with valid data significantly preferred trained settings to untrained settings (paired-samples t test). Seven participants had a significant preference for trained settings, while one had a significant preference for untrained settings (binomial test). The remaining seven participants had nonsignificant preferences. Pooling data across participants, the proportion of times that each setting was chosen in a given environmental sound class was on average very similar. However, breaking down the data by participant revealed strong and idiosyncratic individual preferences. Fourteen participants reported positive feelings of clarity, competence, and mastery when training via HALIC. The obtained data, as well as subjective participant feedback, indicate that smartphones could become viable tools to train hearing aids. Individuals who are tech savvy and have milder HL seem well suited to take advantages of the benefits offered by training with a smartphone. American Academy of Audiology

Superconductor rotor cooling system

DOEpatents

Gamble, Bruce B.; Sidi-Yekhlef, Ahmed; Schwall, Robert E.; Driscoll, David I.; Shoykhet, Boris A.

2004-11-02

A system for cooling a superconductor device includes a cryocooler located in a stationary reference frame and a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with a rotating reference frame in which the superconductor device is located. A method of cooling a superconductor device includes locating a cryocooler in a stationary reference frame, and transferring heat from a superconductor device located in a rotating reference frame to the cryocooler through a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with the rotating reference frame.

Superconductor rotor cooling system

DOEpatents

Gamble, Bruce B.; Sidi-Yekhlef, Ahmed; Schwall, Robert E.; Driscoll, David I.; Shoykhet, Boris A.

2002-01-01

A system for cooling a superconductor device includes a cryocooler located in a stationary reference frame and a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with a rotating reference frame in which the superconductor device is located. A method of cooling a superconductor device includes locating a cryocooler in a stationary reference frame, and transferring heat from a superconductor device located in a rotating reference frame to the cryocooler through a closed circulation system external to the cryocooler. The closed circulation system interfaces the stationary reference frame with the rotating reference frame.

21 CFR 866.5090 - Antimitochondrial antibody immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... immunochemical techniques the antimitochondrial antibodies in human serum. The measurements aid in the diagnosis of diseases that produce a spectrum of autoantibodies (antibodies produced against the body's own... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 866.5120 - Antismooth muscle antibody immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... serum. The measurements aid in the diagnosis of chronic hepatitis (inflammation of the liver) and autoimmune connective tissue diseases (diseases resulting from antibodies produced against the body's own...

21 CFR 866.5120 - Antismooth muscle antibody immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... serum. The measurements aid in the diagnosis of chronic hepatitis (inflammation of the liver) and autoimmune connective tissue diseases (diseases resulting from antibodies produced against the body's own...

21 CFR 866.5120 - Antismooth muscle antibody immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... serum. The measurements aid in the diagnosis of chronic hepatitis (inflammation of the liver) and autoimmune connective tissue diseases (diseases resulting from antibodies produced against the body's own...

21 CFR 866.5090 - Antimitochondrial antibody immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... immunochemical techniques the antimitochondrial antibodies in human serum. The measurements aid in the diagnosis of diseases that produce a spectrum of autoantibodies (antibodies produced against the body's own... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

21 CFR 866.5090 - Antimitochondrial antibody immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... immunochemical techniques the antimitochondrial antibodies in human serum. The measurements aid in the diagnosis of diseases that produce a spectrum of autoantibodies (antibodies produced against the body's own... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test...

Flight Investigation to Improve the Dynamic Longitudinal Stability and Control-Feel Characteristics of the P-63A-1 Airplane (AAF No. 42-68889) with Closely Balanced Experimental Elevators

NASA Technical Reports Server (NTRS)

Johnson, Harold I.

1946-01-01

Results of flight tests of a control-feel aid presented. This device consisted of a spring and dashpot connected in series between the control stick and airplane structure. The device was tested in combination with an experimental elevator and bobweight which had given unsatisfactory dynamic stability and control-feel characteristics in previous tests. The control-feel aid effected marked improvement in both the control-feel characteristics and the control-feel dynamic longitudinal stability of the airplane.

A piezoelectric bone-conduction bending hearing actuator.

PubMed

Adamson, R B A; Bance, M; Brown, J A

2010-10-01

A prototype of a novel bone-conduction hearing actuator based on a piezoelectric bending actuator is presented. The device lies flat against the skull which would allow it to form the basis of a subcutaneous bone-anchored hearing aid. The actuator excites bending in bone through a local bending moment rather than the application of a point force as with conventional bone-anchored hearing aids. Through measurements of the cochlear velocity created by the actuator in embalmed human heads, the device is shown to exhibit high efficiency, making it a possible alternative to present-day electromagnetic bone-vibration actuators.

Portable widefield imaging device for ICG-detection of the sentinel lymph node

NASA Astrophysics Data System (ADS)

Govone, Angelo Biasi; Gómez-García, Pablo Aurelio; Carvalho, André Lopes; Capuzzo, Renato de Castro; Magalhães, Daniel Varela; Kurachi, Cristina

2015-06-01

Metastasis is one of the major cancer complications, since the malignant cells detach from the primary tumor and reaches other organs or tissues. The sentinel lymph node (SLN) is the first lymphatic structure to be affected by the malignant cells, but its location is still a great challenge for the medical team. This occurs due to the fact that the lymph nodes are located between the muscle fibers, making it visualization difficult. Seeking to aid the surgeon in the detection of the SLN, the present study aims to develop a widefield fluorescence imaging device using the indocyanine green as fluorescence marker. The system is basically composed of a 780nm illumination unit, optical components for 810nm fluorescence detection, two CCD cameras, a laptop, and dedicated software. The illumination unit has 16 diode lasers. A dichroic mirror and bandpass filters select and deliver the excitation light to the interrogated tissue, and select and deliver the fluorescence light to the camera. One camera is responsible for the acquisition of visible light and the other one for the acquisition of the ICG fluorescence. The software developed at the LabVIEW® platform generates a real time merged image where it is possible to observe the fluorescence spots, related to the lymph nodes, superimposed at the image under white light. The system was tested in a mice model, and a first patient with tongue cancer was imaged. Both results showed the potential use of the presented fluorescence imaging system assembled for sentinel lymph node detection.

Evaluating the Performance of a Visually Guided Hearing Aid Using a Dynamic Auditory-Visual Word Congruence Task.

PubMed

Roverud, Elin; Best, Virginia; Mason, Christine R; Streeter, Timothy; Kidd, Gerald

2017-12-15

The "visually guided hearing aid" (VGHA), consisting of a beamforming microphone array steered by eye gaze, is an experimental device being tested for effectiveness in laboratory settings. Previous studies have found that beamforming without visual steering can provide significant benefits (relative to natural binaural listening) for speech identification in spatialized speech or noise maskers when sound sources are fixed in location. The aim of the present study was to evaluate the performance of the VGHA in listening conditions in which target speech could switch locations unpredictably, requiring visual steering of the beamforming. To address this aim, the present study tested an experimental simulation of the VGHA in a newly designed dynamic auditory-visual word congruence task. Ten young normal-hearing (NH) and 11 young hearing-impaired (HI) adults participated. On each trial, three simultaneous spoken words were presented from three source positions (-30, 0, and 30 azimuth). An auditory-visual word congruence task was used in which participants indicated whether there was a match between the word printed on a screen at a location corresponding to the target source and the spoken target word presented acoustically from that location. Performance was compared for a natural binaural condition (stimuli presented using impulse responses measured on KEMAR), a simulated VGHA condition (BEAM), and a hybrid condition that combined lowpass-filtered KEMAR and highpass-filtered BEAM information (BEAMAR). In some blocks, the target remained fixed at one location across trials, and in other blocks, the target could transition in location between one trial and the next with a fixed but low probability. Large individual variability in performance was observed. There were significant benefits for the hybrid BEAMAR condition relative to the KEMAR condition on average for both NH and HI groups when the targets were fixed. Although not apparent in the averaged data, some individuals showed BEAM benefits relative to KEMAR. Under dynamic conditions, BEAM and BEAMAR performance dropped significantly immediately following a target location transition. However, performance recovered by the second word in the sequence and was sustained until the next transition. When performance was assessed using an auditory-visual word congruence task, the benefits of beamforming reported previously were generally preserved under dynamic conditions in which the target source could move unpredictably from one location to another (i.e., performance recovered rapidly following source transitions) while the observer steered the beamforming via eye gaze, for both young NH and young HI groups.

Tracking down a solution: exploring the acceptability and value of wearable GPS devices for older persons, individuals with a disability and their support persons.

PubMed

Williamson, Brittany; Aplin, Tammy; de Jonge, Desleigh; Goyne, Matthew

2017-11-01

To explore the acceptability and value of three wearable GPS devices for older persons and individuals with a disability and safety concerns when accessing the community. This pilot study explored six wearers' and their support persons' experience of using three different wearable GPS devices (a pendant, watch, and mini GPS phone), each for a two-week period. Participants identified safety as the main value of using a wearable GPS device. The acceptability and value of these devices was strongly influenced by device features, ease of use, cost, appearance, the reliability of the GPS coordinates, the wearer's health condition and the users familiarity with technology. Overall, participants indicated that they preferred the pendant. Wearable GPS devices are potentially useful in providing individuals who have safety concerns with reassurance and access to assistance as required. To ensure successful utilization, future device design and device selection should consider the user's familiarity with technology and their health condition. This study also revealed that not all wearable GPS devices provide continuous location tracking. It is therefore critical to ensure that the device's location tracking functions address the wearer's requirements and reason for using the device. Implications for Rehabilitation The acceptability and usability of wearable GPS devices is strongly influenced by the device features, ease of use, cost, appearance, the reliability of the device to provide accurate and timely GPS coordinates, as well as the health condition of the wearer and their familiarity with technology. Wearable GPS devices need to be simple to use and support and training is essential to ensure they are successfully utilized. Not all wearable GPS devices provide continuous location tracking and accuracy of location is impacted by line of sight to satellites. Therefore, care needs to be taken when choosing a suitable device, to ensure that the device's location tracking features are based on the wearer's requirements and value behind using the device.

AFB's Computerized Travel Aid: Two Years of Research and Development.

ERIC Educational Resources Information Center

Uslan, Mark M.; And Others

1983-01-01

Progress on the computerized travel aid, an electronic device, using elements of the Polaroid Sonar Camera and a microprocessor, for visually handicapped persons is reviewed, and research on the effectiveness of various models noted. Recommended modifications touch on aspects of mounting, beam shape, and audible outputs. (CL)

49 CFR 38.95 - Mobility aid accessibility.

Code of Federal Regulations, 2014 CFR

2014-10-01

... SPECIFICATIONS FOR TRANSPORTATION VEHICLES Commuter Rail Cars and Systems § 38.95 Mobility aid accessibility. (a)(1) General. All new commuter rail cars, other than level entry cars, covered by this subpart shall...(d) are provided, the car is not required to be equipped with a car-borne device. The access systems...

49 CFR 38.95 - Mobility aid accessibility.

Code of Federal Regulations, 2013 CFR

2013-10-01

... SPECIFICATIONS FOR TRANSPORTATION VEHICLES Commuter Rail Cars and Systems § 38.95 Mobility aid accessibility. (a)(1) General. All new commuter rail cars, other than level entry cars, covered by this subpart shall...(d) are provided, the car is not required to be equipped with a car-borne device. The access systems...

49 CFR 38.95 - Mobility aid accessibility.

Code of Federal Regulations, 2012 CFR

2012-10-01

... SPECIFICATIONS FOR TRANSPORTATION VEHICLES Commuter Rail Cars and Systems § 38.95 Mobility aid accessibility. (a)(1) General. All new commuter rail cars, other than level entry cars, covered by this subpart shall...(d) are provided, the car is not required to be equipped with a car-borne device. The access systems...

47 CFR 95.1211 - Channel use policy.

Code of Federal Regulations, 2010 CFR

2010-10-01

... SERVICES Medical Device Radiocommunication Service (MedRadio) § 95.1211 Channel use policy. (a) The... caused to stations operating in the 400.150-406.000 MHz band in the Meteorological Aids, Meteorological... stations operating in the 400.150-406.000 MHz band in the Meteorological Aids, Meterological Satellite, or...

Protecting Privacy and Securing the Gathering of Location Proofs - The Secure Location Verification Proof Gathering Protocol

NASA Astrophysics Data System (ADS)

Graham, Michelle; Gray, David

As wireless networks become increasingly ubiquitous, the demand for a method of locating a device has increased dramatically. Location Based Services are now commonplace but there are few methods of verifying or guaranteeing a location provided by a user without some specialised hardware, especially in larger scale networks. We propose a system for the verification of location claims, using proof gathered from neighbouring devices. In this paper we introduce a protocol to protect this proof gathering process, protecting the privacy of all involved parties and securing it from intruders and malicious claiming devices. We present the protocol in stages, extending the security of this protocol to allow for flexibility within its application. The Secure Location Verification Proof Gathering Protocol (SLVPGP) has been designed to function within the area of Vehicular Networks, although its application could be extended to any device with wireless & cryptographic capabilities.

A tactile display for international space station (ISS) extravehicular activity (EVA).

PubMed

Rochlis, J L; Newman, D J

2000-06-01

A tactile display to increase an astronaut's situational awareness during an extravehicular activity (EVA) has been developed and ground tested. The Tactor Locator System (TLS) is a non-intrusive, intuitive display capable of conveying position and velocity information via a vibrotactile stimulus applied to the subject's neck and torso. In the Earth's 1 G environment, perception of position and velocity is determined by the body's individual sensory systems. Under normal sensory conditions, redundant information from these sensory systems provides humans with an accurate sense of their position and motion. However, altered environments, including exposure to weightlessness, can lead to conflicting visual and vestibular cues, resulting in decreased situational awareness. The TLS was designed to provide somatosensory cues to complement the visual system during EVA operations. An EVA task was simulated on a computer graphics workstation with a display of the International Space Station (ISS) and a target astronaut at an unknown location. Subjects were required to move about the ISS and acquire the target astronaut using either an auditory cue at the outset, or the TLS. Subjects used a 6 degree of freedom input device to command translational and rotational motion. The TLS was configured to act as a position aid, providing target direction information to the subject through a localized stimulus. Results show that the TLS decreases reaction time (p = 0.001) and movement time (p = 0.001) for simulated subject (astronaut) motion around the ISS. The TLS is a useful aid in increasing an astronaut's situational awareness, and warrants further testing to explore other uses, tasks and configurations.

Using a multi-feature paradigm to measure mismatch responses to minimal sound contrasts in children with cochlear implants and hearing aids.

PubMed

Uhlén, Inger; Engström, Elisabet; Kallioinen, Petter; Nakeva von Mentzer, Cecilia; Lyxell, Björn; Sahlén, Birgitta; Lindgren, Magnus; Ors, Marianne

2017-10-01

Our aim was to explore whether a multi-feature paradigm (Optimum-1) for eliciting mismatch negativity (MMN) would objectively capture difficulties in perceiving small sound contrasts in children with hearing impairment (HI) listening through their hearing aids (HAs) and/or cochlear implants (CIs). Children aged 5-7 years with HAs, CIs and children with normal hearing (NH) were tested in a free-field setting using a multi-feature paradigm with deviations in pitch, intensity, gap, duration, and location. There were significant mismatch responses across all subjects that were positive (p-MMR) for the gap and pitch deviants (F(1,43) = 5.17, p = 0.028 and F(1,43) = 6.56, p = 0.014, respectively) and negative (MMN) for the duration deviant (F(1,43) = 4.74, p = 0.035). Only the intensity deviant showed a significant group interaction with MMN in the HA group and p-MMR in the CI group (F(2,43) = 3.40, p = 0.043). The p-MMR correlated negatively with age, with the strongest correlation in the NH subjects. In the CI group, the late discriminative negativity (LDN) was replaced by a late positivity with a significant group interaction for the location deviant. Children with severe HI can be assessed through their hearing device with a fast multi-feature paradigm. For further studies a multi-feature paradigm including more complex speech sounds may better capture variation in auditory processing in these children. © 2017 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

Childhood pneumonia diagnostics: community health workers' and national stakeholders' differing perspectives of new and existing aids.

PubMed

Spence, Hollie; Baker, Kevin; Wharton-Smith, Alexandra; Mucunguzi, Akasiima; Matata, Lena; Habte, Tedila; Nanyumba, Diana; Sebsibe, Anteneh; Thany, Thol; Källander, Karin

2017-01-01

Pneumonia heavily contributes to global under-five mortality. Many countries use community case management to detect and treat childhood pneumonia. Community health workers (CHWs) have limited tools to help them assess signs of pneumonia. New respiratory rate (RR) counting devices and pulse oximeters are being considered for this purpose. To explore perspectives of CHWs and national stakeholders regarding the potential usability and scalability of seven devices to aid community assessment of pneumonia signs. Pile sorting was conducted to rate the usability and scalability of 7 different RR counting aids and pulse oximeters amongst 16 groups of participants. Following each pile-sorting session, a focus group discussion (FGD) explored participants' sorting rationale. Purposive sampling was used to select CHWs and national stakeholders with experience in childhood pneumonia and integrated community case management (iCCM) in Cambodia, Ethiopia, Uganda and South Sudan. Pile-sorting data were aggregated for countries and participant groups. FGDs were audio recorded and transcribed verbatim. Translated FGDs transcripts were coded in NVivo 10 and analysed using thematic content analysis. Comparative analysis was performed between countries and groups to identify thematic patterns. CHWs and national stakeholders across the four countries perceived the acute respiratory infection (ARI) timer and fingertip pulse oximeter as highly scalable and easy for CHWs to use. National stakeholders were less receptive to new technologies. CHWs placed greater priority on device acceptability to caregivers and children. Both groups felt that heavy reliance on electricity reduced potential scalability and usability in rural areas. Device simplicity, affordability and sustainability were universally valued. CHWs and national stakeholders prioritise different device characteristics according to their specific focus of work. The views of all relevant stakeholders, including health workers, policy makers, children and parents, should be considered in future policy decisions, research and development regarding suitable pneumonia diagnostic aids for community use.

Professionals' views on the use of smartphone technology to support children and adolescents with memory impairment due to acquired brain injury.

PubMed

Plackett, Ruth; Thomas, Sophie; Thomas, Shirley

2017-04-01

Purpose To identify from a health-care professionals' perspective whether smartphones are used by children and adolescents with acquired brain injury as memory aids; what factors predict smartphone use and what barriers prevent the use of smartphones as memory aids by children and adolescents. Method A cross-sectional online survey was undertaken with 88 health-care professionals working with children and adolescents with brain injury. Results Children and adolescents with brain injury were reported to use smartphones as memory aids by 75% of professionals. However, only 42% of professionals helped their clients to use smartphones. The only factor that significantly predicted reported smartphone use was the professionals' positive attitudes toward assistive technology. Several barriers to using smartphones as memory aids were identified, including the poor accessibility of devices and cost of devices. Conclusion Many children and adolescents with brain injury are already using smartphones as memory aids but this is often not facilitated by professionals. Improving the attitudes of professionals toward using smartphones as assistive technology could help to increase smartphone use in rehabilitation. Implications for Rehabilitation Smartphones could be incorporated into rehabilitation programs for young people with brain injury as socially acceptable compensatory aids. Further training and support for professionals on smartphones as compensatory aids could increase professionals' confidence and attitudes in facilitating the use of smartphones as memory aids. Accessibility could be enhanced by the development of a smartphone application specifically designed to be used by young people with brain injury.

Hearing for Success in the Classroom.

ERIC Educational Resources Information Center

Ireland, JoAnn C.; And Others

1988-01-01

Hearing-impaired children in mainstreamed classes require assistive listening devices beyond hearing aids, lipreading, and preferential seating. Frequency modulation auditory training devices can improve speech intelligibility and provide an adequate signal-to-noise ratio, and should be incorporated into regular classes containing hearing-impaired…

Improving Students' Formal Writing: The IDOL Writing Device

ERIC Educational Resources Information Center

Dillon, Patrick J.; Jenkins, J. Jacob

2013-01-01

In this article, the authors describe an acrostic-based mnemonic device they created to aid students in constructing and supporting arguments in a manner consistent with the claim-data-warrant model. They call it the "IDOL writing device": I-"I"dentify a specific claim, D-"D"evelop an argument to support your claim, O-"O"ffer an example(s) that…

Robotic devices and brain-machine interfaces for hand rehabilitation post-stroke.

PubMed

McConnell, Alistair C; Moioli, Renan C; Brasil, Fabricio L; Vallejo, Marta; Corne, David W; Vargas, Patricia A; Stokes, Adam A

2017-06-28

To review the state of the art of robotic-aided hand physiotherapy for post-stroke rehabilitation, including the use of brain-machine interfaces. Each patient has a unique clinical history and, in response to personalized treatment needs, research into individualized and at-home treatment options has expanded rapidly in recent years. This has resulted in the development of many devices and design strategies for use in stroke rehabilitation. The development progression of robotic-aided hand physiotherapy devices and brain-machine interface systems is outlined, focussing on those with mechanisms and control strategies designed to improve recovery outcomes of the hand post-stroke. A total of 110 commercial and non-commercial hand and wrist devices, spanning the 2 major core designs: end-effector and exoskeleton are reviewed. The growing body of evidence on the efficacy and relevance of incorporating brain-machine interfaces in stroke rehabilitation is summarized. The challenges involved in integrating robotic rehabilitation into the healthcare system are discussed. This review provides novel insights into the use of robotics in physiotherapy practice, and may help system designers to develop new devices.

33 CFR 62.47 - Sound signals.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Sound signals. 62.47 Section 62... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.47 Sound signals. (a) Often sound signals are located on or adjacent to aids to navigation. When visual signals are obscured...

33 CFR 62.47 - Sound signals.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Sound signals. 62.47 Section 62... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.47 Sound signals. (a) Often sound signals are located on or adjacent to aids to navigation. When visual signals are obscured...

29 CFR 1910.421 - Pre-dive procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... transportation; and (5) The nearest U.S. Coast Guard Rescue Coordination Center. (c) First aid supplies. (1) A first aid kit appropriate for the diving operation and approved by a physician shall be available at the dive location. (2) When used in a decompression chamber or bell, the first aid kit shall be suitable...

33 CFR 62.47 - Sound signals.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Sound signals. 62.47 Section 62... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.47 Sound signals. (a) Often sound signals are located on or adjacent to aids to navigation. When visual signals are obscured...

33 CFR 62.47 - Sound signals.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Sound signals. 62.47 Section 62... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.47 Sound signals. (a) Often sound signals are located on or adjacent to aids to navigation. When visual signals are obscured...

33 CFR 62.47 - Sound signals.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Sound signals. 62.47 Section 62... UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.47 Sound signals. (a) Often sound signals are located on or adjacent to aids to navigation. When visual signals are obscured...

Development of an attract-and-infect system to control Rhynchophorus ferrugineus with the entomopathogenic fungus Beauveria bassiana.

PubMed

Dembilio, Óscar; Moya, Pilar; Vacas, Sandra; Ortega-García, Lola; Quesada-Moraga, Enrique; Jaques, Josep A; Navarro-Llopis, Vicente

2018-02-09

A new Beauveria bassiana-based attract and infect device (AID) to control Rhynchophorus ferrugineus Olivier (Coleoptera: Curculionidae) was developed. The virulence and persistence of the fungal formulation used in the AID were evaluated in the laboratory. Semi-field and field trials were carried out to validate the results and establish the potential of this device as a control tool. In laboratory conditions, a 50% lethal time (LT 50 ) of 4.33 days was obtained when adults (7-10 days old) were exposed to the inoculation tunnel (IT) containing 1 × 10 10 conidia g -1 in an oil-based fungal formulation. This formulation maintained conidium viability at 50% for up to 2 months. Moreover, when adults were exposed to 2.5-month field-aged ITs, mortality still reached 50% 40 days after exposure. In addition, no differences were observed between ITs aged in early spring and those aged in summer, suggesting that the fungal formulation is not strongly affected by environmental factors in Mediterranean basin conditions. Semi-field assays showed that the device allowed an easy transit of weevils through the IT, which were effectively attracted and infected. Using the AIDs in 4-ha plot field trials, a reduction of >50% in the percentage of infested sentinel palms was obtained. Based on the results obtained in terms of the efficacy and persistence of this new AID in the field and its potential in reducing R. ferrugineus populations and palm infestation, this device could become a key tool for the management of R. ferrugineus. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Fun During Knee Rehabilitation: Feasibility and Acceptability Testing of a New Android-Based Training Device

PubMed Central

Weber-Spickschen, Thomas Sanjay; Colcuc, Christian; Hanke, Alexander; Clausen, Jan-Dierk; James, Paul Abraham; Horstmann, Hauke

2017-01-01

Purpose: The initial goals of rehabilitation after knee injuries and operations are to achieve full knee extension and to activate quadriceps muscle. In addition to regular physiotherapy, an android-based knee training device is designed to help patients achieve these goals and improve compliance in the early rehabilitation period. This knee training device combines fun in a computer game with muscular training or rehabilitation. Our aim was to test the feasibility and acceptability of this new device. Methods: 50 volunteered subjects enrolled to test out the computer game aided device. The first game was the high-striker game, which recorded maximum knee extension power. The second game involved controlling quadriceps muscular power to simulate flying an aeroplane in order to record accuracy of muscle activation. The subjects evaluated this game by completing a simple questionnaire. Results: No technical problem was encountered during the usage of this device. No subjects complained of any discomfort after using this device. Measurements including maximum knee extension power, knee muscle activation and control were recorded successfully. Subjects rated their experience with the device as either excellent or very good and agreed that the device can motivate and monitor the progress of knee rehabilitation training. Conclusion: To the best of our knowledge, this is the first android-based tool available to fast track knee rehabilitation training. All subjects gave very positive feedback to this computer game aided knee device. PMID:29081870

Fitting recommendations and clinical benefit associated with use of the NAL-NL2 hearing-aid prescription in Nucleus cochlear implant recipients.

PubMed

English, Ruth; Plant, Kerrie; Maciejczyk, Michael; Cowan, Robert

2016-01-01

For a group of cochlear implant recipients, who use hearing aids in the contralateral ear, the benefit of NAL-NL2 relative to a recipients' own prescription was assessed. Whether there was a preferred frequency response and/or gain deviation from NAL-NL2 was then investigated. Speech recognition and self-reported ratings of benefit were examined for the recipients' own prescription compared to the NAL-NL2 prescription, in the bimodal and hearing-aid alone conditions. Paired-comparison of hearing-aid frequency response was conducted with default NAL-NL2 and two variants, a low frequency boost or cut. Using a loudness balancing procedure, the hearing-aid gain required to achieve equal loudness between the devices was measured. Sixteen adults with post-lingual hearing loss. A 22% increase in group median word score in quiet with use of NAL-NL2 in the hearing-aid alone condition. In the bimodal condition there was no improvement with NAL-NL2. Default NAL-NL2 frequency response was preferred by 67% of participants. For 56% of participants, the preferred gain to achieve loudness balance across bimodal devices was within 5-dB of prescribed values. The NAL-NL2 prescription provides a high level of clinical performance, and an acceptable frequency response and gain for most participants.

Technology CAD for integrated circuit fabrication technology development and technology transfer

NASA Astrophysics Data System (ADS)

Saha, Samar

2003-07-01

In this paper systematic simulation-based methodologies for integrated circuit (IC) manufacturing technology development and technology transfer are presented. In technology development, technology computer-aided design (TCAD) tools are used to optimize the device and process parameters to develop a new generation of IC manufacturing technology by reverse engineering from the target product specifications. While in technology transfer to manufacturing co-location, TCAD is used for process centering with respect to high-volume manufacturing equipment of the target manufacturing equipment of the target manufacturing facility. A quantitative model is developed to demonstrate the potential benefits of the simulation-based methodology in reducing the cycle time and cost of typical technology development and technology transfer projects over the traditional practices. The strategy for predictive simulation to improve the effectiveness of a TCAD-based project, is also discussed.

Estimation of Radiofrequency Power Leakage from Microwave Ovens for Dosimetric Assessment at Nonionizing Radiation Exposure Levels

PubMed Central

Lopez-Iturri, Peio; de Miguel-Bilbao, Silvia; Aguirre, Erik; Azpilicueta, Leire; Falcone, Francisco; Ramos, Victoria

2015-01-01

The electromagnetic field leakage levels of nonionizing radiation from a microwave oven have been estimated within a complex indoor scenario. By employing a hybrid simulation technique, based on coupling full wave simulation with an in-house developed deterministic 3D ray launching code, estimations of the observed electric field values can be obtained for the complete indoor scenario. The microwave oven can be modeled as a time- and frequency-dependent radiating source, in which leakage, basically from the microwave oven door, is propagated along the complete indoor scenario interacting with all of the elements present in it. This method can be of aid in order to assess the impact of such devices on expected exposure levels, allowing adequate minimization strategies such as optimal location to be applied. PMID:25705676

21 CFR 866.5200 - Carbonic anhydrase B and C immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... immunochemical techniques specific carbonic anhydrase protein molecules in serum and other body fluids. Measurements of carbonic anhydrase B and C aid in the diagnosis of abnormal hemoglobin metabolism. (b...

21 CFR 866.5200 - Carbonic anhydrase B and C immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... immunochemical techniques specific carbonic anhydrase protein molecules in serum and other body fluids. Measurements of carbonic anhydrase B and C aid in the diagnosis of abnormal hemoglobin metabolism. (b...

21 CFR 866.5890 - Inter-alpha trypsin inhibitor immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... measure by immunochemical techniques the inter-alpha trypsin inhibitor (a protein) in serum and other body fluids. Measurement of inter-alpha trypsin inhibitor may aid in the diagnosis of acute bacterial...

21 CFR 866.5200 - Carbonic anhydrase B and C immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... immunochemical techniques specific carbonic anhydrase protein molecules in serum and other body fluids. Measurements of carbonic anhydrase B and C aid in the diagnosis of abnormal hemoglobin metabolism. (b...

21 CFR 866.5890 - Inter-alpha trypsin inhibitor immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... measure by immunochemical techniques the inter-alpha trypsin inhibitor (a protein) in serum and other body fluids. Measurement of inter-alpha trypsin inhibitor may aid in the diagnosis of acute bacterial...

21 CFR 866.5890 - Inter-alpha trypsin inhibitor immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... measure by immunochemical techniques the inter-alpha trypsin inhibitor (a protein) in serum and other body fluids. Measurement of inter-alpha trypsin inhibitor may aid in the diagnosis of acute bacterial...

21 CFR 866.5890 - Inter-alpha trypsin inhibitor immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... measure by immunochemical techniques the inter-alpha trypsin inhibitor (a protein) in serum and other body fluids. Measurement of inter-alpha trypsin inhibitor may aid in the diagnosis of acute bacterial...

21 CFR 866.5200 - Carbonic anhydrase B and C immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological Test... immunochemical techniques specific carbonic anhydrase protein molecules in serum and other body fluids. Measurements of carbonic anhydrase B and C aid in the diagnosis of abnormal hemoglobin metabolism. (b...

Options for Auditory Training for Adults with Hearing Loss.

PubMed

Olson, Anne D

2015-11-01

Hearing aid devices alone do not adequately compensate for sensory losses despite significant technological advances in digital technology. Overall use rates of amplification among adults with hearing loss remain low, and overall satisfaction and performance in noise can be improved. Although improved technology may partially address some listening problems, auditory training may be another alternative to improve speech recognition in noise and satisfaction with devices. The literature underlying auditory plasticity following placement of sensory devices suggests that additional auditory training may be needed for reorganization of the brain to occur. Furthermore, training may be required to acquire optimal performance from devices. Several auditory training programs that are readily accessible for adults with hearing loss, hearing aids, or cochlear implants are described. Programs that can be accessed via Web-based formats and smartphone technology are reviewed. A summary table is provided for easy access to programs with descriptions of features that allow hearing health care providers to assist clients in selecting the most appropriate auditory training program to fit their needs.

A Computer Spreadsheet for Locating Assistive Devices.

ERIC Educational Resources Information Center

Palmer, Catherine V.; Garstecki, Dean C.

1988-01-01

The article presents a directory of assistive devices for persons with hearing impairments in a grid format by distributor and type of device (alerting devices, telephone, TV/radio/stereo, personal communication, group communication, and other). The product locator is also available in spreadsheet form for either the Macintosh or IBM-PC computers.…

Mobility aid for the blind

NASA Technical Reports Server (NTRS)

1982-01-01

A project to develop an effective mobility aid for blind pedestrians which acquires consecutive images of the scenes before a moving pedestrian, which locates and identifies the pedestrian's path and potential obstacles in the path, which presents path and obstacle information to the pedestrian, and which operates in real-time is discussed. The mobility aid has three principal components: an image acquisition system, an image interpretation system, and an information presentation system. The image acquisition system consists of a miniature, solid-state TV camera which transforms the scene before the blind pedestrian into an image which can be received by the image interpretation system. The image interpretation system is implemented on a microprocessor which has been programmed to execute real-time feature extraction and scene analysis algorithms for locating and identifying the pedestrian's path and potential obstacles. Identity and location information is presented to the pedestrian by means of tactile coding and machine-generated speech.

14 CFR 382.127 - What procedures apply to stowage of battery-powered mobility aids?

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 4 2010-01-01 2010-01-01 false What procedures apply to stowage of battery... What procedures apply to stowage of battery-powered mobility aids? (a) Whenever baggage compartment... a passenger's battery-powered wheelchair or other similar mobility device, including the battery, as...

National Science Foundation 1989 Engineering Senior Design Projects To Aid the Disabled.

ERIC Educational Resources Information Center

Enderle, John D., Ed.

Through the Bioengineering and Research to Aid the Disabled program of the National Science Foundation, design projects were awarded competitively to 16 universities. Senior engineering students at each of the universities constructed custom devices and software for disabled individuals. This compendium contains a description of each project in…

14 CFR 382.127 - What procedures apply to stowage of battery-powered mobility aids?

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false What procedures apply to stowage of battery... What procedures apply to stowage of battery-powered mobility aids? (a) Whenever baggage compartment... a passenger's battery-powered wheelchair or other similar mobility device, including the battery, as...

14 CFR 382.127 - What procedures apply to stowage of battery-powered mobility aids?

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 4 2013-01-01 2013-01-01 false What procedures apply to stowage of battery... What procedures apply to stowage of battery-powered mobility aids? (a) Whenever baggage compartment... a passenger's battery-powered wheelchair or other similar mobility device, including the battery, as...

14 CFR 382.127 - What procedures apply to stowage of battery-powered mobility aids?

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 4 2012-01-01 2012-01-01 false What procedures apply to stowage of battery... What procedures apply to stowage of battery-powered mobility aids? (a) Whenever baggage compartment... a passenger's battery-powered wheelchair or other similar mobility device, including the battery, as...

14 CFR 382.127 - What procedures apply to stowage of battery-powered mobility aids?

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 4 2014-01-01 2014-01-01 false What procedures apply to stowage of battery... What procedures apply to stowage of battery-powered mobility aids? (a) Whenever baggage compartment... a passenger's battery-powered wheelchair or other similar mobility device, including the battery, as...

Inventory of Electronic Mobility Aids for Persons with Visual Impairments: A Literature Review

ERIC Educational Resources Information Center

Roentgen, Uta R.; Gelderblom, Gert Jan; Soede, Mathijs; de Witte, Luc P.

2008-01-01

This literature review of existing electronic mobility aids for persons who are visually impaired and recent developments in this field identified and classified 146 products, systems, and devices. The 21 that are currently available that can be used without environmental adaptation are described in functional terms. (Contains 2 tables.)

Technology and Speech Training: An Affair to Remember.

ERIC Educational Resources Information Center

Levitt, Harry

1989-01-01

A history of speech training technology is presented, from the simple hand-held mirror to complicated computer-based systems and tactile devices, and subsequent papers in this theme issue are introduced. Both the advantages and problems of technological aids are addressed. Simplicity in the application and use of speech training aids is stressed.…

Patterns in Student Financial Aid at Rural Community Colleges

ERIC Educational Resources Information Center

Hardy, David E.; Katsinas, Stephen G.

2008-01-01

This article uses the 2005 Basic Classifications of the Carnegie Foundation for the Advancement of Teaching as a framing device through which to examine patterns of student financial aid at America's rural community colleges, which represent 64% of all U.S. community colleges. Rural community colleges serve more first-time, full-time students than…

mHealth and memory aids: levels of smartphone ownership in patients.

PubMed

Migo, Ellen M; Haynes, Becky I; Harris, Lara; Friedner, Kim; Humphreys, Kate; Kopelman, Michael D

2015-01-01

The use of mobile devices to deliver healthcare has not yet been exploited in neuropsychological rehabilitation. Smartphones have the potential to serve as multi-functional memory aids. To investigate whether patients attending a clinic for mixed memory problems own smartphones, to determine whether this could be a widely applicable medium to use as a memory aids device. A questionnaire on smartphone ownership was given to an opportunity sample of consecutive patients attending a neuropsychiatry and memory disorders outpatient clinic. Data were collected in 2012 and repeated 12 months later in 2013 to assess changes over time. Ownership of mobile phones was stable between 2012 (81%) and 2013 (85%), but ownership of smartphones showed a significant increase (from 26% to 40%). Age negatively predicted smartphone ownership. Despite cognitive or psychiatric problems, our patient group are as likely to own a mobile phone as a member of the general population. Ownership levels are at 40% and likely to increase in the future. Exploring how smartphones and their apps could function as memory aids is likely to be useful for a large enough number of patients to be clinically worthwhile.

[Management of hearing impairment in adults].

PubMed

Frachet, Bruno; Poncet-Wallet, Christine; Ernst, Imilie; Quéruel, Françoise; Eshraghi, Adrien

2009-10-20

Hearing impairment, mainly the deafness with possible distortions, assorted with tinnitus concerns about 4 million of the French population. It can be of variable severity. Deafness is an invisible disability until we must answer a question. The permanent improvement of the computer and microelectronics sciences benefit to the prosthetic devices: cochlear implants compensate for complete hearing loss, hearing aids are hidden by being miniaturized, being partially or totally implantable. The management of disability is not limited to this material part: human assistance and assistive devices are part of the armory. Rest to continue and to increase the financial support. This claim is obviously not specific to disability hearing although the hearing aid is only refunded 138 Euro per device for a unit cost from 1300 Euro to 2500 Euro with an observed lifetime of 4 or 5 years.

Synthesis of securement device options and strategies

DOT National Transportation Integrated Search

2002-03-01

The Americans with Disabilities Act of 1990 (ADA) requires that public transit vehicles be equipped with securement location(s) and device(s) that are able to secure common wheelchairs," as defined in the ADA regulations. The definition and size spec...

Assistive Technology Provision Within the Navajo Nation

PubMed Central

Ripat, Jacquie D.

2014-01-01

In this study we explored the factors that affect assistive technology (AT) provision within the Navajo Nation using a qualitative approach to inquiry. Focus groups were held in which AT users discussed their awareness of AT and their need for, use of, and satisfaction with AT devices and services. Twenty-eight individuals who used wheelchairs, orthotics or prosthetics, hearing aids, communication aids, vision aids, and other AT participated in one of seven focus groups. Seven AT providers discussed the facilitators and barriers that affect AT provision. The findings revealed six themes common to both stakeholder groups and two additional themes for AT users. The central theme for AT users centered on (not) feeling understood; the central theme for AT providers revolved around the processes, activities, and roles the providers engaged in at times for different clients. Activities to increase awareness and to promote successful AT provision and satisfaction with AT devices were proposed. PMID:25147224

Poor chest compression quality with mechanical compressions in simulated cardiopulmonary resuscitation: a randomized, cross-over manikin study.

PubMed

Blomberg, Hans; Gedeborg, Rolf; Berglund, Lars; Karlsten, Rolf; Johansson, Jakob

2011-10-01

Mechanical chest compression devices are being implemented as an aid in cardiopulmonary resuscitation (CPR), despite lack of evidence of improved outcome. This manikin study evaluates the CPR-performance of ambulance crews, who had a mechanical chest compression device implemented in their routine clinical practice 8 months previously. The objectives were to evaluate time to first defibrillation, no-flow time, and estimate the quality of compressions. The performance of 21 ambulance crews (ambulance nurse and emergency medical technician) with the authorization to perform advanced life support was studied in an experimental, randomized cross-over study in a manikin setup. Each crew performed two identical CPR scenarios, with and without the aid of the mechanical compression device LUCAS. A computerized manikin was used for data sampling. There were no substantial differences in time to first defibrillation or no-flow time until first defibrillation. However, the fraction of adequate compressions in relation to total compressions was remarkably low in LUCAS-CPR (58%) compared to manual CPR (88%) (95% confidence interval for the difference: 13-50%). Only 12 out of the 21 ambulance crews (57%) applied the mandatory stabilization strap on the LUCAS device. The use of a mechanical compression aid was not associated with substantial differences in time to first defibrillation or no-flow time in the early phase of CPR. However, constant but poor chest compressions due to failure in recognizing and correcting a malposition of the device may counteract a potential benefit of mechanical chest compressions. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

Reference Manual. English for Special Purposes Series: Nursing Aide.

ERIC Educational Resources Information Center

Clark, Marybeth

A variety of reference aids are included in this supplement to a course in English as a second language for nursing aides. Maps of the imaginary geographic locations used in the course are provided. The bulk of the volume presents charts, lists, and illustrations designed to reinforce knowledge of basic vocabulary. Topics covered include numbers,…

21 CFR 866.5510 - Immunoglobulins A, G, M, D, and E immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... antibodies) in serum. Measurement of these immunoglobulins aids in the diagnosis of abnormal protein metabolism and the body's lack of ability to resist infectious agents. (b) Classification. Class II...

21 CFR 866.5530 - Immunoglobulin G (Fc fragment specific) immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... immunoglobulin G (resulting from breakdown of immunoglobulin G antibodies) in urine, serum, and other body fluids. Measurement of immunoglobulin G Fc fragments aids in the diagnosis of plasma cell antibody-forming...

21 CFR 866.5510 - Immunoglobulins A, G, M, D, and E immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... antibodies) in serum. Measurement of these immunoglobulins aids in the diagnosis of abnormal protein metabolism and the body's lack of ability to resist infectious agents. (b) Classification. Class II...

21 CFR 866.5510 - Immunoglobulins A, G, M, D, and E immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... antibodies) in serum. Measurement of these immunoglobulins aids in the diagnosis of abnormal protein metabolism and the body's lack of ability to resist infectious agents. (b) Classification. Class II...

21 CFR 866.5530 - Immunoglobulin G (Fc fragment specific) immunological test system.

Code of Federal Regulations, 2013 CFR

2013-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... immunoglobulin G (resulting from breakdown of immunoglobulin G antibodies) in urine, serum, and other body fluids. Measurement of immunoglobulin G Fc fragments aids in the diagnosis of plasma cell antibody-forming...

21 CFR 866.5530 - Immunoglobulin G (Fc fragment specific) immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... immunoglobulin G (resulting from breakdown of immunoglobulin G antibodies) in urine, serum, and other body fluids. Measurement of immunoglobulin G Fc fragments aids in the diagnosis of plasma cell antibody-forming...

21 CFR 866.5510 - Immunoglobulins A, G, M, D, and E immunological test system.

Code of Federal Regulations, 2014 CFR

2014-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... antibodies) in serum. Measurement of these immunoglobulins aids in the diagnosis of abnormal protein metabolism and the body's lack of ability to resist infectious agents. (b) Classification. Class II...

21 CFR 866.5530 - Immunoglobulin G (Fc fragment specific) immunological test system.

Code of Federal Regulations, 2012 CFR

2012-04-01

... HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunological... immunoglobulin G (resulting from breakdown of immunoglobulin G antibodies) in urine, serum, and other body fluids. Measurement of immunoglobulin G Fc fragments aids in the diagnosis of plasma cell antibody-forming...

21 CFR 866.5180 - Fecal calprotectin immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... immunological test system is an in vitro diagnostic device that consists of reagents used to quantitatively measure, by immunochemical techniques, fecal calprotectin in human stool specimens. The device is intended forin vitro diagnostic use as an aid in the diagnosis of inflammatory bowel diseases (IBD), specifically...

Evaluation of a binary optimization approach to find the optimum locations of energy storage devices in a power grid with stochastically varying loads and wind generation

NASA Astrophysics Data System (ADS)

Dar, Zamiyad

The prices in the electricity market change every five minutes. The prices in peak demand hours can be four or five times more than the prices in normal off peak hours. Renewable energy such as wind power has zero marginal cost and a large percentage of wind energy in a power grid can reduce the price significantly. The variability of wind power prevents it from being constantly available in peak hours. The price differentials between off-peak and on-peak hours due to wind power variations provide an opportunity for a storage device owner to buy energy at a low price and sell it in high price hours. In a large and complex power grid, there are many locations for installation of a storage device. Storage device owners prefer to install their device at locations that allow them to maximize profit. Market participants do not possess much information about the system operator's dispatch, power grid, competing generators and transmission system. The publicly available data from the system operator usually consists of Locational Marginal Prices (LMP), load, reserve prices and regulation prices. In this thesis, we develop a method to find the optimum location of a storage device without using the grid, transmission or generator data. We formulate and solve an optimization problem to find the most profitable location for a storage device using only the publicly available market pricing data such as LMPs, and reserve prices. We consider constraints arising due to storage device operation limitations in our objective function. We use binary optimization and branch and bound method to optimize the operation of a storage device at a given location to earn maximum profit. We use two different versions of our method and optimize the profitability of a storage unit at each location in a 36 bus model of north eastern United States and south eastern Canada for four representative days representing four seasons in a year. Finally, we compare our results from the two versions of our method with a multi period stochastically optimized economic dispatch of the same power system with storage device at locations proposed by our method. We observe a small gap in profit values arising due to the effect of storage device on market prices. However, we observe that the ranking of different locations in terms of profitability remains almost unchanged. This leads us to conclude that our method can successfully predict the optimum locations for installation of storage units in a complex grid using only the publicly available electricity market data.

Automatic cross-sectioning and monitoring system locates defects in electronic devices

NASA Technical Reports Server (NTRS)

Jacobs, G.; Slaughter, B.

1971-01-01

System consists of motorized grinding and lapping apparatus, sample holder, and electronic control circuit. Low power microscope examines device to pinpoint location of circuit defect, and monitor displays output signal when defect is located exactly.

Bulletin of Prosthetics Research. Rehabilitative Engineering Research and Development, Volume 18, Number 2, Fall 1981,

DTIC Science & Technology

1981-01-01

of 140 beats per minute Upper limb prosthetic terminal devices have remained un- could either crutch walk at 60 meters per minute or run at 134...Responses During Binaural Stimulation, TN. Decker and S.W. Howe; J. Functional Effectiveness of a Myo-Electric Prosthesis Compared Acoust. Soc. Amer., 69(4...were whether the aid(s) should be fitted monaurally, binaurally or fitted with hearing aids. Of these, roughly 9,000 were CROS. About 95 percent of

Computer aided design of monolithic microwave and millimeter wave integrated circuits and subsystems

NASA Astrophysics Data System (ADS)

Ku, Walter H.; Gang, Guan-Wan; He, J. Q.; Ichitsubo, I.

1988-05-01

This final technical report presents results on the computer aided design of monolithic microwave and millimeter wave integrated circuits and subsystems. New results include analytical and computer aided device models of GaAs MESFETs and HEMTs or MODFETs, new synthesis techniques for monolithic feedback and distributed amplifiers and a new nonlinear CAD program for MIMIC called CADNON. This program incorporates the new MESFET and HEMT model and has been successfully applied to the design of monolithic millimeter-wave mixers.

Autonomous Landmark Calibration Method for Indoor Localization

PubMed Central

Kim, Jae-Hoon; Kim, Byoung-Seop

2017-01-01

Machine-generated data expansion is a global phenomenon in recent Internet services. The proliferation of mobile communication and smart devices has increased the utilization of machine-generated data significantly. One of the most promising applications of machine-generated data is the estimation of the location of smart devices. The motion sensors integrated into smart devices generate continuous data that can be used to estimate the location of pedestrians in an indoor environment. We focus on the estimation of the accurate location of smart devices by determining the landmarks appropriately for location error calibration. In the motion sensor-based location estimation, the proposed threshold control method determines valid landmarks in real time to avoid the accumulation of errors. A statistical method analyzes the acquired motion sensor data and proposes a valid landmark for every movement of the smart devices. Motion sensor data used in the testbed are collected from the actual measurements taken throughout a commercial building to demonstrate the practical usefulness of the proposed method. PMID:28837071

Field Evaluations of Tracking/Locating Technologies for Prevention of Missing Incidents.

PubMed

Bulat, Tatjana; Kerrigan, Michael V; Rowe, Meredeth; Kearns, William; Craighead, Jeffrey D; Ramaiah, Padmaja

2016-09-01

Persons with dementia are at risk of a missing incident, which is defined as an instance in which a demented person's whereabouts are unknown to the caregiver and the individual is not in an expected location. Since it is critical to determine the missing person's location as quickly as possible, we evaluated whether commercially available tracking technologies can assist in a rapid recovery. This study examined 7 commercially available tracking devices: 3 radio frequency (RF) based and 4 global positioning system (GPS) based, employing realistic tracking scenarios. Outcome measures were time to discovery and degree of deviation from a straight intercept course. Across all scenarios tested, GPS devices were found to be approximately twice as efficient as the RF devices in locating a "missing person." While the RF devices showed reasonable performance at close proximity, the GPS devices were found to be more appropriate overall for tracking/locating missing persons over unknown and larger distances. © The Author(s) 2016.

Challenges and Recent Developments in Hearing Aids: Part II. Feedback and Occlusion Effect Reduction Strategies, Laser Shell Manufacturing Processes, and Other Signal Processing Technologies

PubMed Central

Chung, King

2004-01-01

This is the second part of a review on the challenges and recent developments in hearing aids. Feedback and the occlusion effect pose great challenges in hearing aid design and usage. Yet, conventional solutions to feedback and the occlusion effect often create a dilemma: the solution to one often leads to the other. This review discusses the advanced signal processing strategies to reduce feedback and some new approaches to reduce the occlusion effect. Specifically, the causes of three types of feedback (acoustic, mechanical, and electromagnetic) are discussed. The strategies currently used to reduce acoustic feedback (i.e., adaptive feedback reduction algorithms using adaptive gain reduction, notch filtering, and phase cancellation strategies) and the design of new receivers that are built to reduce mechanical and electromagnetic feedback are explained. In addition, various new strategies (i.e., redesigned sound delivery devices and receiver-in-the-ear-canal hearing aid configuration) to reduce the occlusion effect are reviewed. Many manufacturers have recently adopted laser shell-manufacturing technologies to overcome problems associated with manufacturing custom hearing aid shells. The mechanisms of selected laser sintering and stereo lithographic apparatus and the properties of custom shells produced by these two processes are reviewed. Further, various new developments in hearing aid transducers, telecoils, channel-free amplification, open-platform programming options, rechargeable hearing aids, ear-level frequency modulated (FM) receivers, wireless Bluetooth FM systems, and wireless programming options are briefly explained and discussed. Finally, the applications of advanced hearing aid technologies to enhance other devices such as cochlear implants, hearing protectors, and cellular phones are discussed. PMID:15735871

A haptic unit designed for magnetic-resonance-guided biopsy.

PubMed

Tse, Z T H; Elhawary, H; Rea, M; Young, I; Davis, B L; Lamperth, M

2009-02-01

The magnetic fields present in the magnetic resonance (MR) environment impose severe constraints on any mechatronic device present in its midst, requiring alternative actuators, sensors, and materials to those conventionally used in traditional system engineering. In addition the spatial constraints of closed-bore scanners require a physical separation between the radiologist and the imaged region of the patient. This configuration produces a loss of the sense of touch from the target anatomy for the clinician, which often provides useful information. To recover the force feedback from the tissue, an MR-compatible haptic unit, designed to be integrated with a five-degrees-of-freedom mechatronic system for MR-guided prostate biopsy, has been developed which incorporates position control and force feedback to the operator. The haptic unit is designed to be located inside the scanner isocentre with the master console in the control room. MR compatibility of the device has been demonstrated, showing a negligible degradation of the signal-to-noise ratio and virtually no geometric distortion. By combining information from the position encoder and force sensor, tissue stiffness measurement along the needle trajectory is demonstrated in a lamb liver to aid diagnosis of suspected cancerous tissue.

Modeling strategic behavior in human-automation interaction - Why an 'aid' can (and should) go unused

NASA Technical Reports Server (NTRS)

Kirlik, Alex

1993-01-01

Task-offload aids (e.g., an autopilot, an 'intelligent' assistant) can be selectively engaged by the human operator to dynamically delegate tasks to automation. Introducing such aids eliminates some task demands but creates new ones associated with programming, engaging, and disengaging the aiding device via an interface. The burdens associated with managing automation can sometimes outweigh the potential benefits of automation to improved system performance. Aid design parameters and features of the overall multitask context combine to determine whether or not a task-offload aid will effectively support the operator. A modeling and sensitivity analysis approach is presented that identifies effective strategies for human-automation interaction as a function of three task-context parameters and three aid design parameters. The analysis and modeling approaches provide resources for predicting how a well-adapted operator will use a given task-offload aid, and for specifying aid design features that ensure that automation will provide effective operator support in a multitask environment.

Safety and Efficacy of the BrainPort V100 Device in Individuals Blinded by Traumatic Injury

DTIC Science & Technology

2016-12-01

the functional performance of the BrainPort® V200 device, a non-surgical, FDA approved, sensory substitution system, in persons who are profoundly...The BrainPort V200 device is a wearable, non-surgical, FDA approved, prosthetic device intended for people who are profoundly blind. The BrainPort...BrainPort V200 electronic vision aid (described previously) has been developed under this research. FDA clearance to market the V200 in the US is expected

LAMPPOST: A Mnemonic Device for Teaching Climate Variables

ERIC Educational Resources Information Center

Fahrer, Chuck; Harris, Dan

2004-01-01

This article introduces the word "LAMPPOST" as a mnemonic device to aid in the instruction of climate variables. It provides instructors with a framework for discussing climate patterns that is based on eight variables: latitude, altitude, maritime influence and continentality, pressure systems, prevailing winds, ocean currents, storms, and…

36 CFR 1192.159 - Mobility aid accessibility.

Code of Federal Regulations, 2010 CFR

2010-07-01

... covered by this subpart shall provide a level-change mechanism or boarding device (e.g., lift or ramp... lifts, ramps or bridge plates meeting the applicable requirements of this section are provided at... Transportation, the bus is not required to be equipped with a vehicle-borne device. (b) Vehicle lift—(1) Design...

36 CFR 1192.159 - Mobility aid accessibility.

Code of Federal Regulations, 2011 CFR

2011-07-01

... covered by this subpart shall provide a level-change mechanism or boarding device (e.g., lift or ramp... lifts, ramps or bridge plates meeting the applicable requirements of this section are provided at... Transportation, the bus is not required to be equipped with a vehicle-borne device. (b) Vehicle lift—(1) Design...

21 CFR 884.5300 - Condom.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Condom. 884.5300 Section 884.5300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES... transmitted infections). The device may also be used to collect semen to aid in the diagnosis of infertility...

21 CFR 884.5300 - Condom.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Condom. 884.5300 Section 884.5300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES... transmitted infections). The device may also be used to collect semen to aid in the diagnosis of infertility...

Technologies of the Future.

ERIC Educational Resources Information Center

Lipson, Joseph I.; Fisher, Kathleen M.

1985-01-01

In the future, the requirements of industry will generate a wide range of hardware devices and software programs that will significantly alter and improve the quality of education. The driving forces behind the development of new technological devices include economics; emotional factors, e.g., the desire to develop aids for the handicapped;…

A Signalling Device for Non-Oral Communicators.

ERIC Educational Resources Information Center

King, Thomas W.

1991-01-01

This article describes simple modifications to a basic 9-volt portable transistor radio to serve as a durable, inexpensive signalling device operable by a single external switch. The unit still functions as a radio, but can also help partially speaking students and users of communication aids to signal for help. (Author/PB)

Covariance Analysis of Vision Aided Navigation by Bootstrapping

DTIC Science & Technology

2012-03-22

vision aided navigation. The aircraft uses its INS estimate to geolocate ground features, track those features to aid the INS, and using that aided...development of the 2-D case, including the dynamics and measurement model development, the state space representation and the use of the Kalman filter ...reference frame. This reference frame has its origin located somewhere on an A/C. Normally the origin is set at the A/C center of gravity to allow the use

21 CFR 801.421 - Hearing aid devices; conditions for sale.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) Informs the prospective user that the exercise of the waiver is not in the user's best health interest... that my best health interest would be served if I had a medical evaluation by a licensed physician (preferably a physician who specializes in diseases of the ear) before purchasing a hearing aid. I do not wish...

21 CFR 801.421 - Hearing aid devices; conditions for sale.

Code of Federal Regulations, 2010 CFR

2010-04-01

...) Informs the prospective user that the exercise of the waiver is not in the user's best health interest... that my best health interest would be served if I had a medical evaluation by a licensed physician (preferably a physician who specializes in diseases of the ear) before purchasing a hearing aid. I do not wish...

21 CFR 801.421 - Hearing aid devices; conditions for sale.

Code of Federal Regulations, 2012 CFR

2012-04-01

...) Informs the prospective user that the exercise of the waiver is not in the user's best health interest... that my best health interest would be served if I had a medical evaluation by a licensed physician (preferably a physician who specializes in diseases of the ear) before purchasing a hearing aid. I do not wish...

21 CFR 801.421 - Hearing aid devices; conditions for sale.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Informs the prospective user that the exercise of the waiver is not in the user's best health interest... that my best health interest would be served if I had a medical evaluation by a licensed physician (preferably a physician who specializes in diseases of the ear) before purchasing a hearing aid. I do not wish...

21 CFR 801.421 - Hearing aid devices; conditions for sale.

Code of Federal Regulations, 2013 CFR

2013-04-01

...) Informs the prospective user that the exercise of the waiver is not in the user's best health interest... that my best health interest would be served if I had a medical evaluation by a licensed physician (preferably a physician who specializes in diseases of the ear) before purchasing a hearing aid. I do not wish...

A Simple Laser Teaching Aid for Transverse Mode Structure Demonstration

ERIC Educational Resources Information Center

Ren, Cheng; Zhang, Shulian

2009-01-01

A teaching aid for demonstrating the transverse mode structure in lasers is described. A novel device called "multi-dimension adjustable combined cat-eye reflector" has been constructed from easily available materials to form a He-Ne laser resonator. By finely adjusting the cat-eye, the boundary conditions of the laser cavity can be altered, which…

Proceedings of the International Conference on Sensory Devices for the Blind (London, England, June, 1966).

ERIC Educational Resources Information Center

Dufton, Richard, Ed.

The conference proceedings include papers on sensory aids for visually handicapped mobility and reading. Two papers each treat mobility as a general problem, sociocultural surveys on mobility and reading, and echolocation in man and bats. Five papers concern reports and evaluations of practical trials of the sonic monaural aid; one deals with…

Perception of Consonants in Reverberation and Noise by Adults Fitted with Bimodal Devices

ERIC Educational Resources Information Center

Mason, Michelle; Kokkinakis, Kostas

2014-01-01

Purpose: The purpose of this study was to evaluate the contribution of a contralateral hearing aid to the perception of consonants, in terms of voicing, manner, and place-of-articulation cues in reverberation and noise by adult cochlear implantees aided by bimodal fittings. Method: Eight postlingually deafened adult cochlear implant (CI) listeners…

49 CFR 38.125 - Mobility aid accessibility.

Code of Federal Regulations, 2011 CFR

2011-10-01

... SPECIFICATIONS FOR TRANSPORTATION VEHICLES Intercity Rail Cars and Systems § 38.125 Mobility aid accessibility... cars, other than level entry cars, required to be accessible by §§ 38.111 (a) and (e) of this subpart... complying with § 38.113(d) are provided, the car is not required to be equipped with a car-borne device. (b...

14 CFR 382.121 - What mobility aids and other assistive devices may passengers with a disability bring into the...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 4 2011-01-01 2011-01-01 false What mobility aids and other assistive... Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) SPECIAL REGULATIONS NONDISCRIMINATION ON THE BASIS OF DISABILITY IN AIR TRAVEL Stowage of Wheelchairs, Other Mobility...

Promoting Physical Activity in People with Intellectual and Multiple Disabilities through a Basic Technology-Aided Program

ERIC Educational Resources Information Center

Lancioni, Giulio E.; Singh, Nirbhay N.; O'Reilly, Mark F.; Sigafoos, Jeff; Alberti, Gloria; Perilli, Viviana; Zimbaro, Carmen; Boccasini, Adele; Mazzola, Carlo; Russo, Roberto

2018-01-01

This study assessed a technology-aided program (monitoring responding, and ensuring preferred stimulation and encouragements) for promoting physical activity with 11 participants with severe/profound intellectual and multiple disabilities. Each participant was provided with an exercise device (e.g. a static bicycle and a stepper) and exposed to…

76 FR 22805 - Medical Devices; Reclassification of the Topical Oxygen Chamber for Extremities

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-25

... use and adequate healing of wounds using the TOCE. In addition, FDA has evaluated more than 20 years... humidified oxygen topically at a pressure slightly greater than atmospheric pressure to aid healing of... pressure to aid healing of chronic skin ulcers such as bedsores. Elsewhere in the Federal Register of April...

Ground moving target geo-location from monocular camera mounted on a micro air vehicle

NASA Astrophysics Data System (ADS)

Guo, Li; Ang, Haisong; Zheng, Xiangming

2011-08-01

The usual approaches to unmanned air vehicle(UAV)-to-ground target geo-location impose some severe constraints to the system, such as stationary objects, accurate geo-reference terrain database, or ground plane assumption. Micro air vehicle(MAV) works with characteristics including low altitude flight, limited payload and onboard sensors' low accuracy. According to these characteristics, a method is developed to determine the location of ground moving target which imaged from the air using monocular camera equipped on MAV. This method eliminates the requirements for terrain database (elevation maps) and altimeters that can provide MAV's and target's altitude. Instead, the proposed method only requires MAV flight status provided by its inherent onboard navigation system which includes inertial measurement unit(IMU) and global position system(GPS). The key is to get accurate information on the altitude of the ground moving target. First, Optical flow method extracts background static feature points. Setting a local region around the target in the current image, The features which are on the same plane with the target in this region are extracted, and are retained as aided features. Then, inverse-velocity method calculates the location of these points by integrated with aircraft status. The altitude of object, which is calculated by using position information of these aided features, combining with aircraft status and image coordinates, geo-locate the target. Meanwhile, a framework with Bayesian estimator is employed to eliminate noise caused by camera, IMU and GPS. Firstly, an extended Kalman filter(EKF) provides a simultaneous localization and mapping solution for the estimation of aircraft states and aided features location which defines the moving target local environment. Secondly, an unscented transformation(UT) method determines the estimated mean and covariance of target location from aircraft states and aided features location, and then exports them for the moving target Kalman filter(KF). Experimental results show that our method can instantaneously geo-locate the moving target by operator's single click and can reach 15 meters accuracy for an MAV flying at 200 meters above the ground.

Defense Small Business Innovation Research Program (SBIR), Volume 4, Defense Agencies Abstracts of Phase 1 Awards 1991

DTIC Science & Technology

1991-01-01

EXPERIENCE IN DEVELOPING INTEGRATED OPTICAL DEVICES, NONLINEAR MAGNETIC-OPTIC MATERIALS, HIGH FREQUENCY MODULATORS, COMPUTER-AIDED MODELING AND SOPHISTICATED... HIGH -LEVEL PRESENTATION AND DISTRIBUTED CONTROL MODELS FOR INTEGRATING HETEROGENEOUS MECHANICAL ENGINEERING APPLICATIONS AND TOOLS. THE DESIGN IS FOCUSED...STATISTICALLY ACCURATE WORST CASE DEVICE MODELS FOR CIRCUIT SIMULATION. PRESENT METHODS OF WORST CASE DEVICE DESIGN ARE AD HOC AND DO NOT ALLOW THE

29 CFR 1918.97 - First aid and lifesaving facilities. (See appendix V of this part).

Code of Federal Regulations, 2011 CFR

2011-07-01

... in permanent locations shall be mounted to prevent damage and be protected from the elements if located out-of-doors. If concealed from view, enclosures shall be marked to indicate the location of the...

Two Ears and Two (or More?) Devices: A Pediatric Case Study of Bilateral Profound Hearing Loss

PubMed Central

Uchanski, Rosalie M.; Davidson, Lisa S.; Quadrizius, Sharon; Reeder, Ruth; Cadieux, Jamie; Kettel, Jerrica; Chole, Richard A.

2009-01-01

Advances in technology and expanding candidacy guidelines have motivated many clinics to consider children with precipitously sloping high-frequency hearing loss as candidates for cochlear implants (CIs). A case study is presented of a pediatric CI patient whose hearing thresholds were preserved within 10 dB of preimplant levels (125–750 Hz) after receiving a fully inserted 31.5-mm electrode array at one ear. The primary goal of this study was to explore the possible benefit of using both a hearing aid (HA) and a CI at one ear while using a HA at the opposite ear. The authors find that although the use of bilateral hearing aids with a CI may only provide a slight benefit, careful attention must be paid to the coordinated fitting of devices, especially at the ear with two devices. PMID:19447765

Two ears and two (or more?) devices: a pediatric case study of bilateral profound hearing loss.

PubMed

Uchanski, Rosalie M; Davidson, Lisa S; Quadrizius, Sharon; Reeder, Ruth; Cadieux, Jamie; Kettel, Jerrica; Chole, Richard A

2009-06-01

Advances in technology and expanding candidacy guidelines have motivated many clinics to consider children with precipitously sloping high-frequency hearing loss as candidates for cochlear implants (CIs). A case study is presented of a pediatric CI patient whose hearing thresholds were preserved within 10 dB of preimplant levels (125-750 Hz) after receiving a fully inserted 31.5-mm electrode array at one ear. The primary goal of this study was to explore the possible benefit of using both a hearing aid (HA) and a CI at one ear while using a HA at the opposite ear. The authors find that although the use of bilateral hearing aids with a CI may only provide a slight benefit, careful attention must be paid to the coordinated fitting of devices, especially at the ear with two devices.

Micro-Organ Device

NASA Technical Reports Server (NTRS)

Sun, Wei (Inventor); Chang, Robert C. (Inventor); Starly, Binil (Inventor); Holtorf, Heidi L. (Inventor); Leslie, Julia (Inventor); Culbertson, Christopher (Inventor); Gonda, Steve R. (Inventor)

2013-01-01

A method for fabricating a micro-organ device comprises providing a microscale support having one or more microfluidic channels and one or more micro-chambers for housing a micro-organ and printing a micro-organ on the microscale support using a cell suspension in a syringe controlled by a computer-aided tissue engineering system, wherein the cell suspension comprises cells suspended in a solution containing a material that functions as a three-dimensional scaffold. The printing is performed with the computer-aided tissue engineering system according to a particular pattern. The micro-organ device comprises at least one micro-chamber each housing a micro-organ; and at least one microfluidic channel connected to the micro-chamber, wherein the micro-organ comprises cells arranged in a configuration that includes microscale spacing between portions of the cells to facilitate diffusion exchange between the cells and a medium supplied from the at least one microfluidic channel.

Micro-organ device

NASA Technical Reports Server (NTRS)

von Gustedt-Gonda, legal representative, Iris (Inventor); Holtorf, Heidi L. (Inventor); Gonda, Steve R. (Inventor); Leslie, Julia (Inventor); Chang, Robert C. (Inventor); Sun, Wei (Inventor); Starly, Binil (Inventor); Culbertson, Christopher (Inventor)

2013-01-01

A method for fabricating a micro-organ device comprises providing a microscale support having one or more microfluidic channels and one or more micro-chambers for housing a micro-organ and printing a micro-organ on the microscale support using a cell suspension in a syringe controlled by a computer-aided tissue engineering system, wherein the cell suspension comprises cells suspended in a solution containing a material that functions as a three-dimensional scaffold. The printing is performed with the computer-aided tissue engineering system according to a particular pattern. The micro-organ device comprises at least one micro-chamber each housing a micro-organ; and at least one microfluidic channel connected to the micro-chamber, wherein the micro-organ comprises cells arranged in a configuration that includes microscale spacing between portions of the cells to facilitate diffusion exchange between the cells and a medium supplied from the at least one microfluidic channel.

Development of computer-aided design system of elastic sensitive elements of automatic metering devices

NASA Astrophysics Data System (ADS)

Kalinkina, M. E.; Kozlov, A. S.; Labkovskaia, R. I.; Pirozhnikova, O. I.; Tkalich, V. L.; Shmakov, N. A.

2018-05-01

The object of research is the element base of devices of control and automation systems, including in its composition annular elastic sensitive elements, methods of their modeling, calculation algorithms and software complexes for automation of their design processes. The article is devoted to the development of the computer-aided design system of elastic sensitive elements used in weight- and force-measuring automation devices. Based on the mathematical modeling of deformation processes in a solid, as well as the results of static and dynamic analysis, the calculation of elastic elements is given using the capabilities of modern software systems based on numerical simulation. In the course of the simulation, the model was a divided hexagonal grid of finite elements with a maximum size not exceeding 2.5 mm. The results of modal and dynamic analysis are presented in this article.

A review of wearable technology in medicine.

PubMed

Iqbal, Mohammed H; Aydin, Abdullatif; Brunckhorst, Oliver; Dasgupta, Prokar; Ahmed, Kamran

2016-10-01

With rapid advances in technology, wearable devices have evolved and been adopted for various uses, ranging from simple devices used in aiding fitness to more complex devices used in assisting surgery. Wearable technology is broadly divided into head-mounted displays and body sensors. A broad search of the current literature revealed a total of 13 different body sensors and 11 head-mounted display devices. The latter have been reported for use in surgery (n = 7), imaging (n = 3), simulation and education (n = 2) and as navigation tools (n = 1). Body sensors have been used as vital signs monitors (n = 9) and for posture-related devices for posture and fitness (n = 4). Body sensors were found to have excellent functionality in aiding patient posture and rehabilitation while head-mounted displays can provide information to surgeons to while maintaining sterility during operative procedures. There is a potential role for head-mounted wearable technology and body sensors in medicine and patient care. However, there is little scientific evidence available proving that the application of such technologies improves patient satisfaction or care. Further studies need to be conducted prior to a clear conclusion. © The Royal Society of Medicine.

DSL prescriptive targets for bone conduction devices: adaptation and comparison to clinical fittings.

PubMed

Hodgetts, William E; Scollie, Susan D

2017-07-01

To develop an algorithm that prescribes targets for bone conduction frequency response shape, compression, and output limiting, along with a clinical method that ensures accurate transforms between assessment and verification stages of the clinical workflow. Technical report of target generation and validation. We recruited 39 adult users of unilateral percutaneous bone conduction hearing aids with a range of unilateral, bilateral, mixed and conductive hearing losses across the sample. The initial algorithm over-prescribed output compared to the user's own settings in the low frequencies, but provided a good match to user settings in the high frequencies. Corrections to the targets were derived and implemented as a low-frequency cut aimed at improving acceptance of the wearer's own voice during device use. The DSL-BCD prescriptive algorithm is compatible with verification of devices and fine-tuning to target for percutaneous bone conduction hearing devices that can be coupled to a skull simulator. Further study is needed to investigate the appropriateness of this prescriptive algorithm for other input levels, and for other clinical populations including those with single-sided deafness, bilateral devices, children and users of transcutaneous bone conduction hearing aids.

33 CFR 67.01-5 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AIDS TO NAVIGATION ON ARTIFICIAL ISLANDS AND FIXED STRUCTURES General Requirements § 67.01-5..., drilling barges submerged on location, breakwater barges submerged on location, artificial islands and all...

33 CFR 67.01-5 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AIDS TO NAVIGATION ON ARTIFICIAL ISLANDS AND FIXED STRUCTURES General Requirements § 67.01-5..., drilling barges submerged on location, breakwater barges submerged on location, artificial islands and all...

Space and power efficient hybrid counters array

DOEpatents

Gara, Alan G [Mount Kisco, NY; Salapura, Valentina [Chappaqua, NY

2009-05-12

A hybrid counter array device for counting events. The hybrid counter array includes a first counter portion comprising N counter devices, each counter device for receiving signals representing occurrences of events from an event source and providing a first count value corresponding to a lower order bits of the hybrid counter array. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits of the hybrid counter array. A control device monitors each of the N counter devices of the first counter portion and initiates updating a value of a corresponding second count value stored at the corresponding addressable memory location in the second counter portion. Thus, a combination of the first and second count values provide an instantaneous measure of number of events received.

Space and power efficient hybrid counters array

DOEpatents

Gara, Alan G.; Salapura, Valentina

2010-03-30

A hybrid counter array device for counting events. The hybrid counter array includes a first counter portion comprising N counter devices, each counter device for receiving signals representing occurrences of events from an event source and providing a first count value corresponding to a lower order bits of the hybrid counter array. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits of the hybrid counter array. A control device monitors each of the N counter devices of the first counter portion and initiates updating a value of a corresponding second count value stored at the corresponding addressable memory location in the second counter portion. Thus, a combination of the first and second count values provide an instantaneous measure of number of events received.

The Development of Teaching Aid in The Implementation of Natural Science in The Curriculum 2013 Junior School

NASA Astrophysics Data System (ADS)

Patonah, Siti; Nuvitalia, Duwi; Saptaningrum, Ernawati; Khumaedi; Rusilowati, Ani

2017-04-01

The purpose of this study was to develop the teaching aid required in the curriculum implemented 2013 science subjects at the junior level. The method used in this research is the Research and Development. In this article will be described in the description of the development of the teaching aids that have been generated. Teaching aids consist of three pieces, namely water filtration magical, electric convection box and Musschenbroek bimetal. Based on the expert validation, then all three devices have fulfilled the requirements as teaching aids. Where all three can be used to demonstrate the concept of separation of mixtures, air convection, and thermal expansion of the metal. All three are decent teaching aids used to learn science subjects at junior in implementing the curriculum in 2013.

Language-specific strategy for programming hearing aids - A double-blind randomized controlled crossover study.

PubMed

Matsumoto, Nozomu; Suzuki, Nobuyoshi; Iwasaki, Satoshi; Ishikawa, Kazuha; Tsukiji, Hiroki; Higashino, Yoshie; Tabuki, Tomoko; Nakagawa, Takashi

2018-08-01

Voice-aligned compression (VAC) is a method used in Oticon's hearing aids to provide more comfortable hearing without sacrificing speech discrimination. The complex, non-linear compression curve for the VAC strategy is designed based on the frequency profile of certain spoken Western languages. We hypothesized that hearing aids could be further customized for Japanese-speaking users by modifying the compression curve using the frequency profile of spoken Japanese. A double-blind randomized controlled crossover study was performed to determine whether or not Oticon's modified amplification strategy (VAC-J) provides subjectively preferable hearing aids for Japanese-speaking hearing aid users compared to the same company's original amplification strategy (VAC). The participants were randomized to two groups. The VAC-first group received a pair of hearing aids programmed using the VAC strategy and wore them for three weeks, and then received a pair of hearing aids programmed using VAC-J strategy and wore them for three weeks. The VAC-J-first group underwent the same study, but they received hearing aids in the reverse sequence. A Speech, Spatial and Qualities (SSQ) questionnaire was administered before beginning to use the hearing aids, at the end of using the first pair of hearing aids, and at the end of using the second pair of hearing aids. Twenty-five participants that met the inclusion/exclusion criteria from January 1 to October 31, 2016, were randomized to two groups. Twenty-two participants completed the study. There were no statistically significant differences in the increment of SSQ scores between the participants when using the VAC- or the VAC-J-programmed hearing aids. However, participants preferred the VAC-J strategy to the VAC strategy at the end of the study, and this difference was statistically significant. Japanese-speaking hearing aid users preferred using hearing aids that were fitted with the VAC-J strategy. Our results show that the VAC strategy can be adjusted to the frequency profile of different languages and that participants expressed their subjective preference more clearly than was reflected in the SSQ scores. A similar language-specific strategy may improve user's satisfaction while using hearing devices, and this concept may be extended to implantable hearing devices. R000023191. Copyright © 2017 Elsevier B.V. All rights reserved.

Micro devices using shape memory polymer patches for mated connections

DOEpatents

Lee, Abraham P.; Fitch, Joseph P.

2000-01-01

A method and micro device for repositioning or retrieving miniature devices located in inaccessible areas, such as medical devices (e.g., stents, embolic coils, etc.) located in a blood vessel. The micro repositioning or retrieving device and method uses shape memory polymer (SMP) patches formed into mating geometries (e.g., a hoop and a hook) for re-attachment of the deposited medical device to a catheter or guidewire. For example, SMP or other material hoops are formed on the medical device to be deposited in a blood vessel, and SMP hooks are formed on the micro device attached to a guidewire, whereby the hooks on the micro device attach to the hoops on the medical device, or vice versa, enabling deposition, movement, re-deposit, or retrieval of the medical device. By changing the temperature of the SMP hooks, the hooks can be attached to or released from the hoops located on the medical device. An exemplary method for forming the hooks and hoops involves depositing a sacrificial thin film on a substrate, patterning and processing the thin film to form openings therethrough, depositing or bonding SMP materials in the openings so as to be attached to the substrate, and removing the sacrificial thin film.

Field-Based Experiential Learning Using Mobile Devices

NASA Astrophysics Data System (ADS)

Hilley, G. E.

2015-12-01

Technologies such as GPS and cellular triangulation allow location-specific content to be delivered by mobile devices, but no mechanism currently exists to associate content shared between locations in a way that guarantees the delivery of coherent and non-redundant information at every location. Thus, experiential learning via mobile devices must currently take place along a predefined path, as in the case of a self-guided tour. I developed a mobile-device-based system that allows a person to move through a space along a path of their choosing, while receiving information in a way that guarantees delivery of appropriate background and location-specific information without producing redundancy of content between locations. This is accomplished by coupling content to knowledge-concept tags that are noted as fulfilled when users take prescribed actions. Similarly, the presentation of the content is related to the fulfillment of these knowledge-concept tags through logic statements that control the presentation. Content delivery is triggered by mobile-device geolocation including GPS/cellular navigation, and sensing of low-power Bluetooth proximity beacons. Together, these features implement a process that guarantees a coherent, non-redundant educational experience throughout a space, regardless of a learner's chosen path. The app that runs on the mobile device works in tandem with a server-side database and file-serving system that can be configured through a web-based GUI, and so content creators can easily populate and configure content with the system. Once the database has been updated, the new content is immediately available to the mobile devices when they arrive at the location at which content is required. Such a system serves as a platform for the development of field-based geoscience educational experiences, in which students can organically learn about core concepts at particular locations while individually exploring a space.

Development of a digital hearing aid to meet the Brazilian Government's Ordinance 587 (APAC).

PubMed

Penteado, Silvio Pires; Bento, Ricardo Ferreira

2010-01-01

The treatment of sensorineural hearing loss is based on hearing aids, also known as individual sound amplification devices. The hearing aids purchased by the Brazilian Government, aiming at fulfilling public policies, are based on dedicated components, which bring about benefits, but also render them expensive and may impair repair services after manufacture's warranty expires. to design digital behind-the-ear hearing aids built from standardized components coming from the very supply chain of these manufacturers. experimental. to identify the supply chain of these manufacturers, request samples and set up hearing aids in the laboratory. The developed hearing aids did not show lesser electroacoustic characteristics when compared to those acquired by the Government, also being tested by the same reference international technical standard. It is possible to develop digital behind-the-ear hearing aids based on off-the-shelf components from hearing aid manufacturers' supply chain. Their advantages include low operational costs - for acquisition (with clear advantages for the Government) and service (advantage for the patient).

Blood Pressure Checker

NASA Technical Reports Server (NTRS)

1979-01-01

An estimated 30 million people in the United States have high blood pressure, or hypertension. But a great many of them are unaware of it because hypertension, in its initial stages, displays no symptoms. Thus, the simply-operated blood pressure checking devices now widely located in public places are useful health aids. The one pictured above, called -Medimax 30, is a direct spinoff from NASA technology developed to monitor astronauts in space. For manned space flights, NASA wanted a compact, highly-reliable, extremely accurate method of checking astronauts' blood pressure without the need for a physician's interpretive skill. NASA's Johnson Space Center and Technology, Inc., a contractor, developed an electronic sound processor that automatically analyzes blood flow sounds to get both systolic (contracting arteries) and diastolic (expanding arteries) blood pressure measurements. NASA granted a patent license for this technology to Advanced Life Sciences, Inc., New York City, manufacturers of Medimax 30.

The Regulatory Perspectives on Endoscopic Devices for Obesity.

PubMed

Marrone, April K; Antonino, Mark J; Silverstein, Joshua S; Betz, Martha W; Venkataraman-Rao, Priya; Golding, Martin; Cordray, Diane; Cooper, Jeffrey W

2017-04-01

The recent increase in US Food and Drug Administration-approved weight-loss devices has diversified obesity treatment options. The regulatory pathways for endoscopically placed weight-loss devices and considerations for clinical trials are discussed, including the benefit-risk paradigm intended to aid in weight-loss-device trial development. Also discussed is the benefit-risk analysis of recently approved endoscopic devices. A strategic priority of the FDA Center for Devices and Radiological Health is to increase the use of patient input in decision making. Thus, we consider how endoscopic weight-loss devices with profiles similar to those that have been approved may be viewed in a patient preference study. Published by Elsevier Inc.

Helping the Visually Impaired Student with Electronic Video Visual Aids.

ERIC Educational Resources Information Center

Visualtek, Inc., Santa Monica, CA.

THE FOLLOWING IS THE FULL TEXT OF THIS DOCUMENT: Video visual aids are Closed Circuit TV systems (CCTV's) which magnify print and enlarge it electronically upon a screen so partially sighted persons with some residual vision can read and write normal size print. These devices are in use around the world in homes, schools, industries and libraries,…

Optoelectronic aid for patients with severely restricted visual fields in daylight conditions

NASA Astrophysics Data System (ADS)

Peláez-Coca, María Dolores; Sobrado-Calvo, Paloma; Vargas-Martín, Fernando

2011-11-01

In this study we evaluated the immediate effectiveness of an optoelectronic visual field expander in a sample of subjects with retinitis pigmentosa suffering from a severe peripheral visual field restriction. The aid uses the augmented view concept and provides subjects with visual information from outside their visual field. The tests were carried out in daylight conditions. The optoelectronic aid comprises a FPGA (real-time video processor), a wide-angle mini camera and a transparent see-through head-mounted display. This optoelectronic aid is called SERBA (Sistema Electro-óptico Reconfigurable de Ayuda para Baja Visión). We previously showed that, without compromising residual vision, the SERBA system provides information about objects within an area about three times greater on average than the remaining visual field of the subjects [1]. In this paper we address the effects of the device on mobility under daylight conditions with and without SERBA. The participants were six subjects with retinitis pigmentosa. In this mobility test, better results were obtained when subjects were wearing the SERBA system; specifically, both the number of contacts with low-level obstacles and mobility errors decreased significantly. A longer training period with the device might improve its usefulness.

Value-based design for the elderly: An application in the field of mobility aids.

PubMed

Boerema, Simone T; van Velsen, Lex; Vollenbroek-Hutten, Miriam M R; Hermens, Hermie J

2017-01-01

In the aging society, the need for the elderly to remain mobile and independent is higher than ever. However, many aids supporting mobility often fail to target real needs and lack acceptance. The aim of this study is to demonstrate how value-based design can contribute to the design of mobility aids that address real needs and thus, lead to high acceptance. We elicited values, facilitators, and barriers of mobility of older adults via ten in-depth interviews. Next, we held co-creation sessions, resulting in several designs of innovative mobility aids, which were evaluated for acceptance via nine in-depth interviews. The interviews resulted in a myriad of key values, such as "independence from family" and "doing their own groceries." Design sessions resulted in three designs for a wheeled walker. Their acceptance was rather low. Current mobility device users were more eager to accept the designs than non-users. The value-based approach offers designers a close look into the lives of the elderly, thereby opening up a wide range of innovation possibilities that better fit their actual needs. Product service systems seem to be a promising focus for targeting human needs in mobility device design.

Use and Acceptance of AAC Systems by Children with Angelman Syndrome

ERIC Educational Resources Information Center

Calculator, Stephen N.

2013-01-01

Background: This investigation of children with Angelman syndrome (AS) examined reported uses of electronic augmentative and alternative communication (AAC) devices (i.e. VOCAs), including speech generating devices, in relation to other aided and unaided methods of communication. Materials and Method: A total of 122 parents of children with AS,…

Use of the Sonicguide and Laser Cane in Obtaining or Keeping Employment.

ERIC Educational Resources Information Center

Jacobson, William H.; Smith, Tom E. C.

1983-01-01

Owners of laser canes and Sonicguides were surveyed to determine whether these devices were used in employment settings. Of the 94 respondents, 74 were still using their electronic travel aids: 36 percent used the devices to travel to and from work, and 49 percent used them on the job. (SEW)

Touch NMR: An NMR Data Processing Application for the iPad

ERIC Educational Resources Information Center

Li, Qiyue; Chen, Zhiwei; Yan, Zhiping; Wang, Cheng; Chen, Zhong

2014-01-01

Nuclear magnetic resonance (NMR) spectroscopy has become one of the most powerful technologies to aid research in numerous scientific disciplines. With the development of consumer electronics, mobile devices have played increasingly important roles in our daily life. However, there is currently no application available for mobile devices able to…

21 CFR 866.6030 - AFP-L3% immunological test system.

Code of Federal Regulations, 2011 CFR

2011-04-01

... system is an in vitro device that consists of reagents and an automated instrument used to quantitatively measure, by immunochemical techniques, AFP and AFP-L3 subfraction in human serum. The device is intended for in vitro diagnostic use as an aid in the risk assessment of patients with chronic liver disease...

49 CFR 38.159 - Mobility aid accessibility.

Code of Federal Regulations, 2010 CFR

2010-10-01

... boarding device (e.g., lift or ramp) complying with paragraph (b) or (c) of this section and sufficient...) Exception. If portable or station-based lifts, ramps or bridge plates meeting the applicable requirements of... device. (b) Vehicle lift—(1) Design load. The design load of the lift shall be at least 600 pounds (2665...

49 CFR 38.159 - Mobility aid accessibility.

Code of Federal Regulations, 2011 CFR

2011-10-01

... boarding device (e.g., lift or ramp) complying with paragraph (b) or (c) of this section and sufficient...) Exception. If portable or station-based lifts, ramps or bridge plates meeting the applicable requirements of... device. (b) Vehicle lift—(1) Design load. The design load of the lift shall be at least 600 pounds (2665...

Advances Underlying Spoken Language Development: A Century of Building on Bell.

ERIC Educational Resources Information Center

Ling, Daniel

1990-01-01

This article compares Alexander Graham Bell's achievements in the areas of instruction and technology for the hearing impaired with contemporary techniques and devices, many of which stem from his work. Assessment techniques, cochlear implants, tactile devices and visual aids are discussed as well as other alternatives and supplements to residual…

Crawling Aid

NASA Technical Reports Server (NTRS)

1982-01-01

The Institute for the Achievement of Human Potential developed a device known as the Vehicle for Initial Crawling (VIC); the acronym is a tribute to the crawler's inventor, Hubert "Vic" Vykukal; is an effective crawling aid. The VIC is used by brain injured children who are unable to crawl due to the problems of weight-bearing and friction, caused by gravity. It is a rounded plywood frame large enough to support the child's torso, leaving arms and legs free to move. On its underside are three aluminum discs through which air is pumped to create an air-bearing surface that has less friction than a film of oil. Upper side contains the connection to the air supply and a pair of straps which restrain the child and cause the device to move with him. VIC is used with the intent to recreate the normal neurological connection between brain and muscles. Over repetitive use of the device the child develops his arm and leg muscles as well as coordination. Children are given alternating therapy, with and without the VIC until eventually the device is no longer needed.

Counter Unmanned Aerial System Decision-Aid Logic Process (C-UAS DALP)

DTIC Science & Technology

decision -aid or logic process that bridges the middle elements of the kill... of use, location, general logic process , and reference mission. This is the framework for the IDEF0 functional architecture diagrams, decision -aid diagrams, logic process , and modeling and simulation....chain between detection to countermeasure response. This capstone project creates the logic for a decision process that transitions from the

RECORDING DEVICE FOR 128 CHANNEL IONIZATION CHAMBERS (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goryunov, N.N.

1959-05-01

Descriptions are given of a 128-channel amplitude recording device desiged for operation with ionization chambers. Each channl has a large puse recording dynamic amplitude range (amplitudes can vary from each other up to 8000 fold). The recording of amplitudes is accomplished by photographing pulses on a cathode ray tube. With the aid of a commutation device it is possible to record 64 pulses simultaneously on one tube screen. (tr-auth)

Safety and Efficacy of the BrainPort V100 Device in Individuals Blinded by Traumatic Injury

DTIC Science & Technology

2015-10-01

within the next quarter. 15 . SUBJECT TERMS BrainPort, V100, V200, blindness, visual impairment, assistive device, assistive technology, visual aid, non...2. Keywords 4 3. Accomplishments 4 4. Impact 10 5 . Changes/Problems 10 6. Products 10 7. Participants & Other...design were finalized during the 4 th quarter. The headset frame design (plastic and silicone components) was completed and device hardware 5 and

Mark of the Moessbauer

NASA Technical Reports Server (NTRS)

2004-01-01

This image, taken by an instrument called the microscopic imager on the Mars Exploration Rover Spirit, reveals an imprint left by another instrument, the Moessbauer spectrometer. The imprint is at a location within the rover wheel track named 'Middle of Road.' Both instruments are located on the rover's instrument deployment device, or 'arm.'

Not only was the Moessbauer spectrometer able to gain important mineralogical information about this site, it also aided in the placement of the microscopic imager. On hard rocks, the microscopic imager uses its tiny metal sensor to determine proper placement for best possible focus. However, on the soft martian soil this guide would sink, prohibiting proper placement of the microscopic imager. After the Moessbauer spectrometer's much larger, donut-shaped plate touches the surface, Spirit can correctly calculate where to position the microscopic imager.

Scientists find this image particularly interesting because of the compacted nature of the soil that was underneath the Moessbauer spectrometer plate. Also of interest are the embedded, round grains and the fractured appearance of the material disturbed within the hole. The material appears to be slightly cohesive. The field of view in this image, taken on Sol 43 (February 16, 2004), measures approximately 3 centimeters (1.2 inches) across.

Emergency information systems for cars

NASA Astrophysics Data System (ADS)

Thirunavukkarasu, M.; Vani Manasa, N.; Kumar, K. Rajesh; Sundar, S.

2017-11-01

The main objective of this work is to create a Health Care monitoring and Guidance system for persons who are travelling in outdoor environments like cars. GSM (Global System for Mobile Communications) and GPS (Global Positioning System) technologies are separately and combined today in many applications in our day to day life. The GSM module will send a message along with the GPS location to the end user through text, and a call is initiated to the user for further instructions. The Global Positioning System (GPS) will give the location of the interested vehicle. This system helps the doctor or anyone to monitor the accident who is outdoor and has less help. This will help the hospital to monitor the accident as well as guide the injured through difficult situations. Using a buzzer, the persons nearby will come to know that the person is in danger or in poor health conditions. This project provides a good two-way communication with the injured and the hospital to assist them to give first aid before an ambulance arrives. So, this paper devices a novel technique to assist the people who just met with accident through GPS and GSM.

Medical Signal-Conditioning and Data-Interface System

NASA Technical Reports Server (NTRS)

Braun, Jeffrey; Jacobus, charles; Booth, Scott; Suarez, Michael; Smith, Derek; Hartnagle, Jeffrey; LePrell, Glenn

2006-01-01

A general-purpose portable, wearable electronic signal-conditioning and data-interface system is being developed for medical applications. The system can acquire multiple physiological signals (e.g., electrocardiographic, electroencephalographic, and electromyographic signals) from sensors on the wearer s body, digitize those signals that are received in analog form, preprocess the resulting data, and transmit the data to one or more remote location(s) via a radiocommunication link and/or the Internet. The system includes a computer running data-object-oriented software that can be programmed to configure the system to accept almost any analog or digital input signals from medical devices. The computing hardware and software implement a general-purpose data-routing-and-encapsulation architecture that supports tagging of input data and routing the data in a standardized way through the Internet and other modern packet-switching networks to one or more computer(s) for review by physicians. The architecture supports multiple-site buffering of data for redundancy and reliability, and supports both real-time and slower-than-real-time collection, routing, and viewing of signal data. Routing and viewing stations support insertion of automated analysis routines to aid in encoding, analysis, viewing, and diagnosis.

An indentation depth-force sensing wheeled probe for abnormality identification during minimally invasive surgery.

PubMed

Liu, H; Puangmali, P; Zbyszewski, D; Elhage, O; Dasgupta, P; Dai, J S; Seneviratne, L; Althoefer, K

2010-01-01

This paper presents a novel wheeled probe for the purpose of aiding a surgeon in soft tissue abnormality identification during minimally invasive surgery (MIS), compensating the loss of haptic feedback commonly associated with MIS. Initially, a prototype for validating the concept was developed. The wheeled probe consists of an indentation depth sensor employing an optic fibre sensing scheme and a force/torque sensor. The two sensors work in unison, allowing the wheeled probe to measure the tool-tissue interaction force and the rolling indentation depth concurrently. The indentation depth sensor was developed and initially tested on a homogenous silicone phantom representing a good model for a soft tissue organ; the results show that the sensor can accurately measure the indentation depths occurring while performing rolling indentation, and has good repeatability. To validate the ability of the wheeled probe to identify abnormalities located in the tissue, the device was tested on a silicone phantom containing embedded hard nodules. The experimental data demonstrate that recording the tissue reaction force as well as rolling indentation depth signals during rolling indentation, the wheeled probe can rapidly identify the distribution of tissue stiffness and cause the embedded hard nodules to be accurately located.

User acceptance of location-tracking technologies in health research: Implications for study design and data quality.

PubMed

Hardy, Jean; Veinot, Tiffany C; Yan, Xiang; Berrocal, Veronica J; Clarke, Philippa; Goodspeed, Robert; Gomez-Lopez, Iris N; Romero, Daniel; Vydiswaran, V G Vinod

2018-03-01

Research regarding place and health has undergone a revolution due to the availability of consumer-focused location-tracking devices that reveal fine-grained details of human mobility. Such research requires that participants accept such devices enough to use them in their daily lives. There is a need for a theoretically grounded understanding of acceptance of different location-tracking technology options, and its research implications. Guided by an extended Unified Theory of Acceptance and Use of Technology (UTAUT), we conducted a 28-day field study comparing 21 chronically ill people's acceptance of two leading, consumer-focused location-tracking technologies deployed for research purposes: (1) a location-enabled smartphone, and (2) a GPS watch/activity tracker. Participants used both, and completed two surveys and qualitative interviews. Findings revealed that all participants exerted effort to facilitate data capture, such as by incorporating devices into daily routines and developing workarounds to keep devices functioning. Nevertheless, the smartphone was perceived to be significantly easier and posed fewer usability challenges for participants than the watch. Older participants found the watch significantly more difficult to use. For both devices, effort expectancy was significantly associated with future willingness to participate in research although prosocial motivations overcame some concerns. Social influence, performance expectancy and use behavior were significantly associated with intentions to use the devices in participants' personal lives. Data gathered via the smartphone was significantly more complete than data gathered via the watch, primarily due to usability challenges. To make longer-term participation in location tracking research a reality, and to achieve complete data capture, researchers must minimize the effort involved in participation; this requires usable devices. For long-term location-tracking studies using similar devices, findings indicate that only smartphone-based tracking is up to the challenge. Copyright © 2018 Elsevier Inc. All rights reserved.

Rollator use and functional outcome of geriatric rehabilitation.

PubMed

Vogt, Lutz; Lucki, Katrin; Bach, Matthias; Banzer, Winfried

2010-01-01

In a quasi-experimental pre- and postdesign, we examined the effect of rollator use on functional rehabilitation outcome in geriatric patients.From a sample of 458 geriatric inpatients, we matched 30 subjects who were not using assistive devices in their everyday lives but received a wheeled walker at the time of hospital admission (first-time user group) according to their admission scores on three motor performance tests (Timed Up-and-Go, Five-Times-Sit-to-Stand, and Performance-Oriented Mobility Assessment -Balance) with 30 patients who were actively using rollators as their primary walking aid for at least 3 months (long-term user group) and 30 control subjects without walking-aid assistance. Measurements were repeated after the inpatient rehabilitation regimen.The Kruskal-Wallis test did not reveal significant group differences in rehabilitation progress. Controls and device users, regardless of walking-aid experience, demonstrated nearly comparable mobility, strength, and balance improvements. More than half of each cohort (controls, n = 22; first-time, n = 17; long-term, n = 18) achieved functional gains in all three motor tests.The study showed that rollator assistance does not interfere with rehabilitation outcome and, to some extent, legitimates the prescription of assistive devices to improve confidence and restore or maintain motor ability at the highest possible level.

Using an Augmented Reality Device as a Distance-based Vision Aid-Promise and Limitations.

PubMed

Kinateder, Max; Gualtieri, Justin; Dunn, Matt J; Jarosz, Wojciech; Yang, Xing-Dong; Cooper, Emily A

2018-06-06

For people with limited vision, wearable displays hold the potential to digitally enhance visual function. As these display technologies advance, it is important to understand their promise and limitations as vision aids. The aim of this study was to test the potential of a consumer augmented reality (AR) device for improving the functional vision of people with near-complete vision loss. An AR application that translates spatial information into high-contrast visual patterns was developed. Two experiments assessed the efficacy of the application to improve vision: an exploratory study with four visually impaired participants and a main controlled study with participants with simulated vision loss (n = 48). In both studies, performance was tested on a range of visual tasks (identifying the location, pose and gesture of a person, identifying objects, and moving around in an unfamiliar space). Participants' accuracy and confidence were compared on these tasks with and without augmented vision, as well as their subjective responses about ease of mobility. In the main study, the AR application was associated with substantially improved accuracy and confidence in object recognition (all P < .001) and to a lesser degree in gesture recognition (P < .05). There was no significant change in performance on identifying body poses or in subjective assessments of mobility, as compared with a control group. Consumer AR devices may soon be able to support applications that improve the functional vision of users for some tasks. In our study, both artificially impaired participants and participants with near-complete vision loss performed tasks that they could not do without the AR system. Current limitations in system performance and form factor, as well as the risk of overconfidence, will need to be overcome.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

A microfluidic circulatory system integrated with capillary-assisted pressure sensors.

PubMed

Chen, Yangfan; Chan, Ho Nam; Michael, Sean A; Shen, Yusheng; Chen, Yin; Tian, Qian; Huang, Lu; Wu, Hongkai

2017-02-14

The human circulatory system comprises a complex network of blood vessels interconnecting biologically relevant organs and a heart driving blood recirculation throughout this system. Recreating this system in vitro would act as a bridge between organ-on-a-chip and "body-on-a-chip" and advance the development of in vitro models. Here, we present a microfluidic circulatory system integrated with an on-chip pressure sensor to closely mimic human systemic circulation in vitro. A cardiac-like on-chip pumping system is incorporated in the device. It consists of four pumping units and passive check valves, which mimic the four heart chambers and heart valves, respectively. Each pumping unit is independently controlled with adjustable pressure and pump rate, enabling users to control the mimicked blood pressure and heartbeat rate within the device. A check valve is located downstream of each pumping unit to prevent backward leakage. Pulsatile and unidirectional flow can be generated to recirculate within the device by programming the four pumping units. We also report an on-chip capillary-assisted pressure sensor to monitor the pressure inside the device. One end of the capillary was placed in the measurement region, while the other end was sealed. Time-dependent pressure changes were measured by recording the movement of the liquid-gas interface in the capillary and calculating the pressure using the ideal gas law. The sensor covered the physiologically relevant blood pressure range found in humans (0-142.5 mmHg) and could respond to 0.2 s actuation time. With the aid of the sensor, the pressure inside the device could be adjusted to the desired range. As a proof of concept, human normal left ventricular and arterial pressure profiles were mimicked inside this device. Human umbilical vein endothelial cells (HUVECs) were cultured on chip and cells can respond to mechanical forces generated by arterial-like flow patterns.

A phone-assistive device based on Bluetooth technology for cochlear implant users.

PubMed

Qian, Haifeng; Loizou, Philipos C; Dorman, Michael F

2003-09-01

Hearing-impaired people, and particularly hearing-aid and cochlear-implant users, often have difficulty communicating over the telephone. The intelligibility of telephone speech is considerably lower than the intelligibility of face-to-face speech. This is partly because of lack of visual cues, limited telephone bandwidth, and background noise. In addition, cellphones may cause interference with the hearing aid or cochlear implant. To address these problems that hearing-impaired people experience with telephones, this paper proposes a wireless phone adapter that can be used to route the audio signal directly to the hearing aid or cochlear implant processor. This adapter is based on Bluetooth technology. The favorable features of this new wireless technology make the adapter superior to traditional assistive listening devices. A hardware prototype was built and software programs were written to implement the headset profile in the Bluetooth specification. Three cochlear implant users were tested with the proposed phone-adapter and reported good speech quality.

32 CFR 728.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... adjuncts such as prosthetic devices, spectacles, hearing aids, orthopedic footwear, and other medically... retaining management, any additional material, professional diagnostic or consultative services, or other...

Job Seeker's Aids: A Systematic Approach for Organizing Employer Contacts

ERIC Educational Resources Information Center

Ugland, Richard P.

1977-01-01

Job Seeker's Aids is a step-by-step procedure that can be used by rehabilitation counselors to help clients locate and visit manufacturing, institutional, and other places of employment for the purpose of identifying and applying for job openings. (Author)

Infrared detector device inspection system

DOEpatents

Soehnel, Grant; Bender, Daniel A.

2016-08-09

Methods and apparatuses for identifying carrier lifetimes are disclosed herein. In a general embodiment, a beam of light is sent to a group of locations on a material for an optical device. Photons emitted from the material are detected at each of the group of locations. A carrier lifetime is identified for each of the group of locations based on the photons detected from each of the group of locations.

Better together: reduced compliance after sequential versus simultaneous bilateral hearing aids fitting.

PubMed

Lavie, Limor; Banai, Karen; Attias, Joseph; Karni, Avi

2014-03-01

The purpose of this study was to determine the effects of sequential versus simultaneous bilateral hearing aids fitting on patient compliance. Thirty-six older adults with hearing impairment participated in this study. Twelve were fitted with bilateral hearing aids simultaneously. The remaining participants were fitted sequentially: One hearing aid (to the left or to the right ear) was used initially; 1 month later, the other ear was also fitted with a hearing aid for bilateral use. Self-reports on usefulness and compliance were elicited after the first and second months of hearing aid use. In addition, the number of hours the hearing aids were used was extracted from the data loggings of each device. Simultaneous fitting resulted in high levels of compliance and consistent usage throughout the study period. Sequential fitting resulted in abrupt reduction in compliance and hours of use once the second hearing aid was added, both in the clinical scoring and in the data loggings. Simultaneous fitting of bilateral hearing aids results in better compliance compared with sequential fitting. The addition of a second hearing aid after a relatively short period of monaural use may lead to inconsistent use of both hearing aids.

Utility of a simple lighting device to improve chest compressions learning.

PubMed

González-Calvete, L; Barcala-Furelos, R; Moure-González, J D; Abelairas-Gómez, C; Rodríguez-Núñez, A

2017-11-01

The recommendations on cardiopulmonary resuscitation (CPR) emphasize the quality of the manoeuvres, especially chest compressions (CC). Audiovisual feedback devices could improve the quality of the CC during CPR. The aim of this study was to evaluate the usefulness of a simple lighting device as a visual aid during CPR on a mannequin. Twenty-two paediatricians who attended an accredited paediatric CPR course performed, in random order, 2min of CPR on a mannequin without and with the help of a simple lighting device, which flashes at a frequency of 100 cycles per minute. The following CC variables were analyzed using a validated compression quality meter (CPRmeter ® ): depth, decompression, rate, CPR time and percentage of compressions. With the lighting device, participants increased average quality (60.23±54.50 vs. 79.24±9.80%; P=.005), percentage in target depth (48.86±42.67 vs. 72.95±20.25%; P=.036) and rate (35.82±37.54 vs. 67.09±31.95%; P=.024). A simple light device that flashes at the recommended frequency improves the quality of CC performed by paediatric residents on a mannequin. The usefulness of this CPR aid system should be assessed in real patients. Copyright © 2017 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Publicado por Elsevier España, S.L.U. All rights reserved.

A three-dimensional evaluation of a laser scanner and a touch-probe scanner.

PubMed

Persson, Anna; Andersson, Matts; Oden, Agneta; Sandborgh-Englund, Gunilla

2006-03-01

The fit of a dental restoration depends on quality throughout the entire manufacturing process. There is difficulty in assessing the surface topography of an object with a complex form, such as teeth, since there is no exact reference form. The purpose of this study was to determine the repeatability and relative accuracy of 2 dental surface digitization devices. A computer-aided design (CAD) technique was used for evaluation to calculate and present the deviations 3-dimensionally. Ten dies of teeth prepared for complete crowns were fabricated in presintered yttria-stabilized tetragonal zirconia (Y-TZP). The surfaces were digitized 3 times each with an optical or mechanical digitizer. The number of points in the point clouds from each reading were calculated and used as the CAD reference model (CRM). Alignments were performed by registration software that works by minimizing a distance criterion. In color-difference maps, the distribution of the discrepancies between the surfaces in the CRM and the 3-dimensional surface models was identified and located. The repeatability of both scanners was within 10 microm, based on SD and absolute mean values. The qualitative evaluation resulted in an even distribution of the deviations in the optical digitizer, whereas the dominating part of the surfaces in the mechanical digitizer showed no deviations. The relative accuracy of the 2 surface digitization devices was within +/- 6 microm, based on median values. The repeatability of the optical digitizer was comparable with the mechanical digitization device, and the relative accuracy was similar.

46 CFR 108.241 - Visual aids.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1) Have a wind direction indicator located in an unobstructed area readily visible to helicopter pilots... considering deck configuration, helicopter type, and operational requirements. (b) All markings must be in a...

46 CFR 108.241 - Visual aids.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1) Have a wind direction indicator located in an unobstructed area readily visible to helicopter pilots... considering deck configuration, helicopter type, and operational requirements. (b) All markings must be in a...

46 CFR 108.241 - Visual aids.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1) Have a wind direction indicator located in an unobstructed area readily visible to helicopter pilots... considering deck configuration, helicopter type, and operational requirements. (b) All markings must be in a...

46 CFR 108.241 - Visual aids.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1) Have a wind direction indicator located in an unobstructed area readily visible to helicopter pilots... considering deck configuration, helicopter type, and operational requirements. (b) All markings must be in a...

46 CFR 108.241 - Visual aids.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Construction and Arrangement Helicopter Facilities § 108.241 Visual aids. (a) Each helicopter deck must— (1) Have a wind direction indicator located in an unobstructed area readily visible to helicopter pilots... considering deck configuration, helicopter type, and operational requirements. (b) All markings must be in a...

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

31. DETAIL OF OVERHEAD TENSIONER DEVICE LOCATED ABOVE SOUTHERN DOOR OF BUILDING 1. - Chollas Heights Naval Radio Transmitting Facility, Transmitter Building, 6410 Zero Road, San Diego, San Diego County, CA

Traveling-wave device with mass flux suppression

DOEpatents

Swift, Gregory W.; Backhaus, Scott N.; Gardner, David L.

2000-01-01

A traveling-wave device is provided with the conventional moving pistons eliminated. Acoustic energy circulates in a direction through a fluid within a torus. A side branch may be connected to the torus for transferring acoustic energy into or out of the torus. A regenerator is located in the torus with a first heat exchanger located on a first side of the regenerator downstream of the regenerator relative to the direction of the circulating acoustic energy; and a second heat exchanger located on an upstream side of the regenerator. The improvement is a mass flux suppressor located in the torus to minimize time-averaged mass flux of the fluid. In one embodiment, the device further includes a thermal buffer column in the torus to thermally isolate the heat exchanger that is at the operating temperature of the device.

21 CFR 880.5760 - Chemical cold pack snakebite kit.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Chemical cold pack snakebite kit. 880.5760 Section... Therapeutic Devices § 880.5760 Chemical cold pack snakebite kit. (a) Identification. A chemical cold pack snakebit kit is a device consisting of a chemical cold pack and tourniquet used for first-aid treatment of...

21 CFR 880.5760 - Chemical cold pack snakebite kit.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Chemical cold pack snakebite kit. 880.5760 Section... Therapeutic Devices § 880.5760 Chemical cold pack snakebite kit. (a) Identification. A chemical cold pack snakebit kit is a device consisting of a chemical cold pack and tourniquet used for first-aid treatment of...

An Automated Pronunciation - Hearing Instruction Aid: Refinements and Applications

ERIC Educational Resources Information Center

Smith, Donald L.

1975-01-01

Describes an automated device for teaching and testing the pronunciation of a language to a non-native speaker without the assistance of a trained teacher. This device was developed at the Research Institute of Logopedics and Phoniatrics at the University of Tokyo. Available from SIGLASH, c/o ACM, P.O. Box 12105, Church St. Station, New York, NY…

Human Factors Engineering Bibliographic Series. Volume 2: 1960-1964 Literature

DTIC Science & Technology

1966-10-01

flutter discrimination, melodic and temporal) binaural vs. monaural equipment and methods (e.g., anechoic chambers, audiometric devices, communication...brightness, duration, timbre, vocality) stimulus mixtures (e.g., harmonics, beats , combination tones, modulations) thresholds training, nonverbal--see Training...scales and aids) Beats --see Audition (stimulus mixtures) Bells--see Auditory (displays, nonverbal) Belts, Harnesses, and other Restraining Devices--see

21 CFR 880.5760 - Chemical cold pack snakebite kit.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Chemical cold pack snakebite kit. 880.5760 Section... Therapeutic Devices § 880.5760 Chemical cold pack snakebite kit. (a) Identification. A chemical cold pack snakebit kit is a device consisting of a chemical cold pack and tourniquet used for first-aid treatment of...

21 CFR 880.5760 - Chemical cold pack snakebite kit.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Chemical cold pack snakebite kit. 880.5760 Section... Therapeutic Devices § 880.5760 Chemical cold pack snakebite kit. (a) Identification. A chemical cold pack snakebit kit is a device consisting of a chemical cold pack and tourniquet used for first-aid treatment of...

21 CFR 880.5760 - Chemical cold pack snakebite kit.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Chemical cold pack snakebite kit. 880.5760 Section... Therapeutic Devices § 880.5760 Chemical cold pack snakebite kit. (a) Identification. A chemical cold pack snakebit kit is a device consisting of a chemical cold pack and tourniquet used for first-aid treatment of...

Astronaut C. Michael Foale is briefed on use of Sky Genie

NASA Technical Reports Server (NTRS)

1994-01-01

Astronaut C. Michael Foale, STS-63 mission specialist, is briefed on the use of Sky Genie device by Karin L. Porter. The device would aid in emergency egress operations aboard a troubled Space Shuttle. Porter, an employee of Rockwell International, helps train astronauts in egress procedures at JSC's Shuttle mockup and integration laboratory.

Automation in Vocational Training of the Mentally Retarded. Final Report.

ERIC Educational Resources Information Center

Platt, Henry; And Others

Various uses of automation in teaching were studied with mentally retarded (IQ 70 to 90) and/or emotionally disturbed (IQ 80 to 90) youth aged 16 to 20. Programed instruction was presented by six audiovisual devices and techniques: the Devereux Model 50 Teaching Aid, the Learn-Ease Teaching Device, the Mast Teaching Machine, the Graflex…

Identifying the best locations to install flow control devices in sewer networks to enable in-sewer storage

NASA Astrophysics Data System (ADS)

Leitão, J. P.; Carbajal, J. P.; Rieckermann, J.; Simões, N. E.; Sá Marques, A.; de Sousa, L. M.

2018-01-01

The activation of available in-sewer storage volume has been suggested as a low-cost flood and combined sewer overflow mitigation measure. However, it is currently unknown what the attributes for suitable objective functions to identify the best location for flow control devices are and the impact of those attributes on the results. In this study, we present a novel location model and efficient algorithm to identify the best location(s) to install flow limiters. The model is a screening tool that does not require hydraulic simulations but rather considers steady state instead of simplistic static flow conditions. It also maximises in-sewer storage according to different reward functions that also considers the potential impact of flow control device failure. We demonstrate its usefulness on two real sewer networks, for which an in-sewer storage potential of approximately 2,000 m3 and 500 m3 was estimated with five flow control devices installed.

The Role of Computational Modeling and Simulation in the Total Product Life Cycle of Peripheral Vascular Devices

PubMed Central

Morrison, Tina M.; Dreher, Maureen L.; Nagaraja, Srinidhi; Angelone, Leonardo M.; Kainz, Wolfgang

2018-01-01

The total product life cycle (TPLC) of medical devices has been defined by four stages: discovery and ideation, regulatory decision, product launch, and postmarket monitoring. Manufacturers of medical devices intended for use in the peripheral vasculature, such as stents, inferior vena cava (IVC) filters, and stent-grafts, mainly use computational modeling and simulation (CM&S) to aid device development and design optimization, supplement bench testing for regulatory decisions, and assess postmarket changes or failures. For example, computational solid mechanics and fluid dynamics enable the investigation of design limitations in the ideation stage. To supplement bench data in regulatory submissions, manufactures can evaluate the effects of anatomical characteristics and expected in vivo loading environment on device performance. Manufacturers might also harness CM&S to aid root-cause analyses that are necessary when failures occur postmarket, when the device is exposed to broad clinical use. Once identified, CM&S tools can then be used for redesign to address the failure mode and re-establish the performance profile with the appropriate models. The Center for Devices and Radiological Health (CDRH) wants to advance the use of CM&S for medical devices and supports the development of virtual physiological patients, clinical trial simulations, and personalized medicine. Thus, the purpose of this paper is to describe specific examples of how CM&S is currently used to support regulatory submissions at different phases of the TPLC and to present some of the stakeholder-led initiatives for advancing CM&S for regulatory decision-making. PMID:29479395

The Role of Computational Modeling and Simulation in the Total Product Life Cycle of Peripheral Vascular Devices.

PubMed

Morrison, Tina M; Dreher, Maureen L; Nagaraja, Srinidhi; Angelone, Leonardo M; Kainz, Wolfgang

2017-01-01

The total product life cycle (TPLC) of medical devices has been defined by four stages: discovery and ideation, regulatory decision, product launch, and postmarket monitoring. Manufacturers of medical devices intended for use in the peripheral vasculature, such as stents, inferior vena cava (IVC) filters, and stent-grafts, mainly use computational modeling and simulation (CM&S) to aid device development and design optimization, supplement bench testing for regulatory decisions, and assess postmarket changes or failures. For example, computational solid mechanics and fluid dynamics enable the investigation of design limitations in the ideation stage. To supplement bench data in regulatory submissions, manufactures can evaluate the effects of anatomical characteristics and expected in vivo loading environment on device performance. Manufacturers might also harness CM&S to aid root-cause analyses that are necessary when failures occur postmarket, when the device is exposed to broad clinical use. Once identified, CM&S tools can then be used for redesign to address the failure mode and re-establish the performance profile with the appropriate models. The Center for Devices and Radiological Health (CDRH) wants to advance the use of CM&S for medical devices and supports the development of virtual physiological patients, clinical trial simulations, and personalized medicine. Thus, the purpose of this paper is to describe specific examples of how CM&S is currently used to support regulatory submissions at different phases of the TPLC and to present some of the stakeholder-led initiatives for advancing CM&S for regulatory decision-making.

Processes in construction of failure management expert systems from device design information

NASA Technical Reports Server (NTRS)

Malin, Jane T.; Lance, Nick

1987-01-01

This paper analyzes the tasks and problem solving methods used by an engineer in constructing a failure management expert system from design information about the device to te diagnosed. An expert test engineer developed a trouble-shooting expert system based on device design information and experience with similar devices, rather than on specific expert knowledge gained from operating the device or troubleshooting its failures. The construction of the expert system was intensively observed and analyzed. This paper characterizes the knowledge, tasks, methods, and design decisions involved in constructing this type of expert system, and makes recommendations concerning tools for aiding and automating construction of such systems.

Power capacity from earcanal dynamic motion

NASA Astrophysics Data System (ADS)

Carioli, Johan; Delnavaz, Aidin; Zednik, Ricardo J.; Voix, Jérémie

2016-12-01

In-ear devices, such as a hearing aids, electronic earplugs, and wearables, need electrical power to operate. Batteries are the current solution, but unfortunately they also create other problems. For example, several hundred million users, mostly elderly, must change their hearing aid batteries on a weekly basis, which represents not only significant financial costs but a negative environmental impact. A promising alternative involves harvesting energy by converting the dynamic jaw movements into electrical energy via the earcanal. The extent that jaw movements distort the earcanal is still unknown, making it difficult to design the appropriate energy harvesting system for the earplug. Moreover, the finite element methods are barely capable to model the behavior of the earcanal distortion because of the complexity of mechanisms that deform the earcanal. However, this paper presents an alternative method, based on analytical considerations, to understand in-ear mechanical quasi-static deformations using earcanal point clouds. This model quantifies the bending and compressive movements of the earcanal. It can therefore be used to select an appropriate deformation mode for harvesting energy from the earcanal's dynamic motion. The value of this approach was illustrated by calculating the obtainable mechanical energy from 12 human subjects. On average, the bending energy in a human earcanal was found to be three times greater than the radial compression energy. This key finding will need to be considered in the design of future in-ear energy harvesting devices. Such an energy harvesting device has the potential to revolutionize the market for in-ear wearable devices and hearing aids by complementing or replacing battery technology.

Low latency counter event indication

DOEpatents

Gara, Alan G [Mount Kisco, NY; Salapura, Valentina [Chappaqua, NY

2008-09-16

A hybrid counter array device for counting events with interrupt indication includes a first counter portion comprising N counter devices, each for counting signals representing event occurrences and providing a first count value representing lower order bits. An overflow bit device associated with each respective counter device is additionally set in response to an overflow condition. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits. An operatively coupled control device monitors each associated overflow bit device and initiates incrementing a second count value stored at a corresponding memory location in response to a respective overflow bit being set. The incremented second count value is compared to an interrupt threshold value stored in a threshold register, and, when the second counter value is equal to the interrupt threshold value, a corresponding "interrupt arm" bit is set to enable a fast interrupt indication. On a subsequent roll-over of the lower bits of that counter, the interrupt will be fired.

Low latency counter event indication

DOEpatents

Gara, Alan G.; Salapura, Valentina

2010-08-24

A hybrid counter array device for counting events with interrupt indication includes a first counter portion comprising N counter devices, each for counting signals representing event occurrences and providing a first count value representing lower order bits. An overflow bit device associated with each respective counter device is additionally set in response to an overflow condition. The hybrid counter array includes a second counter portion comprising a memory array device having N addressable memory locations in correspondence with the N counter devices, each addressable memory location for storing a second count value representing higher order bits. An operatively coupled control device monitors each associated overflow bit device and initiates incrementing a second count value stored at a corresponding memory location in response to a respective overflow bit being set. The incremented second count value is compared to an interrupt threshold value stored in a threshold register, and, when the second counter value is equal to the interrupt threshold value, a corresponding "interrupt arm" bit is set to enable a fast interrupt indication. On a subsequent roll-over of the lower bits of that counter, the interrupt will be fired.

Electric current locator

DOEpatents

King, Paul E [Corvallis, OR; Woodside, Charles Rigel [Corvallis, OR

2012-02-07

The disclosure herein provides an apparatus for location of a quantity of current vectors in an electrical device, where the current vector has a known direction and a known relative magnitude to an input current supplied to the electrical device. Mathematical constants used in Biot-Savart superposition equations are determined for the electrical device, the orientation of the apparatus, and relative magnitude of the current vector and the input current, and the apparatus utilizes magnetic field sensors oriented to a sensing plane to provide current vector location based on the solution of the Biot-Savart superposition equations. Description of required orientations between the apparatus and the electrical device are disclosed and various methods of determining the mathematical constants are presented.

33 CFR 64.31 - Determination of hazard to navigation.

Code of Federal Regulations, 2013 CFR

2013-07-01

... AIDS TO NAVIGATION MARKING OF STRUCTURES, SUNKEN VESSELS AND OTHER OBSTRUCTIONS Miscellaneous...) Location of the obstruction in relation to other obstructions or aids to navigation; (h) Prevailing and historical weather conditions; (i) Length of time that the obstruction has been in existence; (j) History of...

33 CFR 64.31 - Determination of hazard to navigation.

Code of Federal Regulations, 2014 CFR

2014-07-01

... AIDS TO NAVIGATION MARKING OF STRUCTURES, SUNKEN VESSELS AND OTHER OBSTRUCTIONS Miscellaneous...) Location of the obstruction in relation to other obstructions or aids to navigation; (h) Prevailing and historical weather conditions; (i) Length of time that the obstruction has been in existence; (j) History of...

33 CFR 64.31 - Determination of hazard to navigation.

Code of Federal Regulations, 2011 CFR

2011-07-01

... AIDS TO NAVIGATION MARKING OF STRUCTURES, SUNKEN VESSELS AND OTHER OBSTRUCTIONS Miscellaneous...) Location of the obstruction in relation to other obstructions or aids to navigation; (h) Prevailing and historical weather conditions; (i) Length of time that the obstruction has been in existence; (j) History of...

33 CFR 64.31 - Determination of hazard to navigation.

Code of Federal Regulations, 2012 CFR

2012-07-01

... AIDS TO NAVIGATION MARKING OF STRUCTURES, SUNKEN VESSELS AND OTHER OBSTRUCTIONS Miscellaneous...) Location of the obstruction in relation to other obstructions or aids to navigation; (h) Prevailing and historical weather conditions; (i) Length of time that the obstruction has been in existence; (j) History of...

33 CFR 64.31 - Determination of hazard to navigation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... AIDS TO NAVIGATION MARKING OF STRUCTURES, SUNKEN VESSELS AND OTHER OBSTRUCTIONS Miscellaneous...) Location of the obstruction in relation to other obstructions or aids to navigation; (h) Prevailing and historical weather conditions; (i) Length of time that the obstruction has been in existence; (j) History of...

Auditory Processing Disorders

MedlinePlus

... Loss Hearing Loss in Seniors Hearing Aids General Information Types Features Fittings Assistive Listening & Alerting Devices Cochlear Implants Aural Rehabilitation Auditory Processing Disorders (APDs) Common Conditions Dizziness Tinnitus Who Are ...

CHARGING OF DEVICES BY MICROWAVE POWER BEAMING

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A. (Inventor)

2005-01-01

A system for providing wireless, charging power and/or primary power to electronic/electrical devices is described whereby microwave energy is employed. Microwave energy is focused by a power transmitter comprising one or more adaptively-phased microwave array emitters onto a device to be charged. Rectennas within the device to be charged receive and rectify the microwave energy and use it for battery charging and/or for primary power. A locator signal generated by the device to be charged is analyzed by the system to determine the location of the device to be charged relative to the microwave array emitters, permitting thc microwave energy to be directly specifically towards the device to be charged. Backscatter detectors respond to backscatter energy reflected off of any obstacle between the device to be charged and the microwave array emitters. Power to any obstructed microwave array emitter is reduced until the obstruction is removed. Optionally, data can be modulated onto microwave energy beams produced by the array emitter and demodulated by the device, thereby providing means of data communication from the power transmitter to the device. Similarly, data can be modulated onto the locator signal and demodulated in the power transmitter, thereby providing means of data communication from the device to the power transmitter.

Operator vision aids for space teleoperation assembly and servicing

NASA Technical Reports Server (NTRS)

Brooks, Thurston L.; Ince, Ilhan; Lee, Greg

1992-01-01

This paper investigates concepts for visual operator aids required for effective telerobotic control. Operator visual aids, as defined here, mean any operational enhancement that improves man-machine control through the visual system. These concepts were derived as part of a study of vision issues for space teleoperation. Extensive literature on teleoperation, robotics, and human factors was surveyed to definitively specify appropriate requirements. This paper presents these visual aids in three general categories of camera/lighting functions, display enhancements, and operator cues. In the area of camera/lighting functions concepts are discussed for: (1) automatic end effector or task tracking; (2) novel camera designs; (3) computer-generated virtual camera views; (4) computer assisted camera/lighting placement; and (5) voice control. In the technology area of display aids, concepts are presented for: (1) zone displays, such as imminent collision or indexing limits; (2) predictive displays for temporal and spatial location; (3) stimulus-response reconciliation displays; (4) graphical display of depth cues such as 2-D symbolic depth, virtual views, and perspective depth; and (5) view enhancements through image processing and symbolic representations. Finally, operator visual cues (e.g., targets) that help identify size, distance, shape, orientation and location are discussed.

Promoting physical activity in people with intellectual and multiple disabilities through a basic technology-aided program.

PubMed

Lancioni, Giulio E; Singh, Nirbhay N; O'Reilly, Mark F; Sigafoos, Jeff; Alberti, Gloria; Perilli, Viviana; Zimbaro, Carmen; Boccasini, Adele; Mazzola, Carlo; Russo, Roberto

2018-06-01

This study assessed a technology-aided program (monitoring responding, and ensuring preferred stimulation and encouragements) for promoting physical activity with 11 participants with severe/profound intellectual and multiple disabilities. Each participant was provided with an exercise device (e.g. a static bicycle and a stepper) and exposed to the program according to an ABAB design, in which A and B represented baseline and intervention phases, respectively. Data recording concerned (a) the participants' responses with the exercise device (e.g. pedaling) during baseline and intervention phases and (b) their heart rates during the last intervention phase. The results showed that all participants had significant increases in responding with the exercise devices during the intervention phases. Heart-rate values during the intervention sessions indicated that the participants' responding during those sessions mostly amounted to moderate-intensity physical activity, with potential benefits for their overall physical condition. Implications of the findings and questions for future research in the area were discussed.

[Assessment criteria in the choice of aids for the lifting of patients].

PubMed

Panciera, D; Menoni, O; Ricci, M G; Occhipinti, E

1999-01-01

A fundamental part of the prevention strategies aimed at reducing risk due to manual handling of patients is the use of appropriate aids. This paper defines the basic types of aids for hospital wards: patient lifting devices, aids for hygiene and minor aids; and also proposes a procedure for choice of the type of aid: the procedure uses a specific protocol and also analyzes work organization and the environmental features of the ward. The proposed criteria for choice concern in the first place the fundamental requirements of the equipment: safety for operator and patient, simplicity of use and comfort for the patient. Secondly the basic determinants for choice of the type of aid are the type of disabled patient usually present in the ward and the analysis of the movements made in handling patients. On this basis, for each type of aid, the specific features are defined which direct the choice of supply for the various wards that will be adequate and effective both in reducing risk due to manual handling of patients and in improving the comfort of the patients.

Privacy preserving, real-time and location secured biometrics for mCommerce authentication

NASA Astrophysics Data System (ADS)

Kuseler, Torben; Al-Assam, Hisham; Jassim, Sabah; Lami, Ihsan A.

2011-06-01

Secure wireless connectivity between mobile devices and financial/commercial establishments is mature, and so is the security of remote authentication for mCommerce. However, the current techniques are open for hacking, false misrepresentation, replay and other attacks. This is because of the lack of real-time and current-precise-location in the authentication process. This paper proposes a new technique that includes freshly-generated real-time personal biometric data of the client and present-position of the mobile device used by the client to perform the mCommerce so to form a real-time biometric representation to authenticate any remote transaction. A fresh GPS fix generates the "time and location" to stamp the biometric data freshly captured to produce a single, real-time biometric representation on the mobile device. A trusted Certification Authority (CA) acts as an independent authenticator of such client's claimed realtime location and his/her provided fresh biometric data. Thus eliminates the necessity of user enrolment with many mCommerce services and application providers. This CA can also "independently from the client" and "at that instant of time" collect the client's mobile device "time and location" from the cellular network operator so to compare with the received information, together with the client's stored biometric information. Finally, to preserve the client's location privacy and to eliminate the possibility of cross-application client tracking, this paper proposes shielding the real location of the mobile device used prior to submission to the CA or authenticators.

Time-Gating Processes in Intra-Cavity Mode-Locking Devices Like Saturable Absorbers and Kerr Cells

NASA Technical Reports Server (NTRS)

Prasad, Narasimha; Roychoudhuri, Chandrasekhar

2010-01-01

Photons are non-interacting entities. Light beams do not interfere by themselves. Light beams constituting different laser modes (frequencies) are not capable of re-arranging their energies from extended time-domain to ultra-short time-domain by themselves without the aid of light-matter interactions with suitable intra-cavity devices. In this paper we will discuss the time-gating properties of intra-cavity "mode-locking" devices that actually help generate a regular train of high energy wave packets.

Piping and tubing technology: A compilation

NASA Technical Reports Server (NTRS)

1971-01-01

A compilation on the devices, techniques, and methods used in piping and tubing technology is presented. Data cover the following: (1) a number of fittings, couplings, and connectors that are useful in joining tubing and piping and various systems, (2) a family of devices used where flexibility and/or vibration damping are necessary, (3) a number of devices found useful in the regulation and control of fluid flow, and (4) shop hints to aid in maintenance and repair procedures such as cleaning, flaring, and swaging of tubes.

Reconstructing Spatial Distributions from Anonymized Locations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horey, James L; Forrest, Stephanie; Groat, Michael

2012-01-01

Devices such as mobile phones, tablets, and sensors are often equipped with GPS that accurately report a person's location. Combined with wireless communication, these devices enable a wide range of new social tools and applications. These same qualities, however, leave location-aware applications vulnerable to privacy violations. This paper introduces the Negative Quad Tree, a privacy protection method for location aware applications. The method is broadly applicable to applications that use spatial density information, such as social applications that measure the popularity of social venues. The method employs a simple anonymization algorithm running on mobile devices, and a more complex reconstructionmore » algorithm on a central server. This strategy is well suited to low-powered mobile devices. The paper analyzes the accuracy of the reconstruction method in a variety of simulated and real-world settings and demonstrates that the method is accurate enough to be used in many real-world scenarios.« less

A passive cold storage device economic model to evaluate selected immunization location scenarios.

PubMed

Norman, Bryan A; Nourollahi, Sevnaz; Chen, Sheng-I; Brown, Shawn T; Claypool, Erin G; Connor, Diana L; Schmitz, Michelle M; Rajgopal, Jayant; Wateska, Angela R; Lee, Bruce Y

2013-10-25

The challenge of keeping vaccines cold at health posts given the unreliability of power sources in many low- and middle-income countries and the expense and maintenance requirements of solar refrigerators has motivated the development of passive cold storage devices (PCDs), containers that keep vaccines cold without using an active energy source. With different PCDs under development, manufacturers, policymakers and funders need guidance on how varying different PCD characteristics may affect the devices' cost and utility. We developed an economic spreadsheet model representing the lowest two levels of a typical Expanded Program on Immunization (EPI) vaccine supply chain: a district store, the immunization locations that the district store serves, and the transport vehicles that operate between the district store and the immunization locations. The model compares the use of three vaccine storage device options [(1) portable PCDs, (2) stationary PCDs, or (3) solar refrigerators] and allows the user to vary different device (e.g., size and cost) and scenario characteristics (e.g., catchment area population size and vaccine schedule). For a sample set of select scenarios and equipment specification, we found the portable PCD to generally be better suited to populations of 5,000 or less. The stationary PCD replenished once per month can be a robust design especially with a 35L capacity and a cost of $2,500 or less. The solar device was generally a reasonable alternative for most of the scenarios explored if the cost was $2,100 or less (including installation). No one device type dominated over all explored circumstances. Therefore, the best device may vary from country-to-country and location-to-location within a country. This study introduces a quantitative model to help guide PCD development. Although our selected set of explored scenarios and device designs was not exhaustive, future explorations can further alter model input values to represent additional scenarios and device designs. Copyright © 2013 Elsevier Ltd. All rights reserved.

Reducing Deviance Through Youths' Mutual Aid Group Dynamics.

PubMed

Cheung, Chau-kiu; Ngai, Steven Sek-yum

2016-01-01

The mutual aid group, as supported by the social worker, emerges to play a vital role in helping group members reduce their deviance or behavioral problem. However, how the collaboration of the group and social worker accomplishes the reduction has remained uncharted. Based on social capital theory, mutual aid and cohesion within the group and social workers' specific aid for the group are likely responsible for the reduction. The test of such hypotheses relies on a two-wave panel survey of the members of 60 mutual aid groups who had deviant behavioral problems, located in Hong Kong, China. These groups had 241 youths completing both initial and 1-year follow-up surveys. Results manifested the direct or unconditional contributions of mutual aid, group cohesion, and social workers' specific aid to reducing deviance. Hence, social workers can enhance the effectiveness of the mutual aid group in reducing youths' deviance. © The Author(s) 2014.

Evolution of low-profile and lightweight electrical connectors for soldier-worn applications

NASA Astrophysics Data System (ADS)

Gans, Eric; Lee, Kang; Jannson, Tomasz; Walter, Kevin

2011-06-01

In addition to military radios, modern warfighters carry cell phones, GPS devices, computers, and night-vision aids, all of which require electrical cables and connectors for data and power transmission. Currently each electrical device operates via independent cables using conventional cable and connector technology. Conventional cables are stiff and difficult to integrate into a soldier-worn garment. Conventional connectors are tall and heavy, as they were designed to ensure secure connections to bulkhead-type panels, and being tall, represent significant snag-hazards in soldier-worn applications. Physical Optics Corporation has designed a new, lightweight and low-profile electrical connector that is more suitable for body-worn applications and operates much like a standard garment snap. When these connectors are mated, the combined height is <0.3 in. - a significant reduction from the 2.5 in. average height of conventional connectors. Electrical connections can be made with one hand (gloved or bare) and blindly (without looking). Furthermore, POC's connectors are integrated into systems that distribute data or power from a central location on the soldier's vest, reducing the length and weight of the cables necessary to interconnect various mission-critical electronic systems. The result is a lightweight power/data distribution system offering significant advantages over conventional electrical connectors in soldier-worn applications.

Rapid detection of Cu(2+) by a paper-based microfluidic device coated with bovine serum albumin (BSA)-Au nanoclusters.

PubMed

Fang, Xueen; Zhao, Qianqian; Cao, Hongmei; Liu, Juan; Guan, Ming; Kong, Jilie

2015-11-21

In this work, bovine serum albumin (BSA)-Au nanoclusters were used to coat a paper-based microfluidic device. This device acted as a Cu(2+) biosensor that showed fluorescence quenching on detection of copper ions. The detection limit of this sensor could be adjusted by altering the water absorbing capacity of the device. Qualitative and semi-quantitative results could be obtained visually without the aid of any advanced instruments. This sensor could test Cu(2+) rapidly with high specificity and sensitivity, which would be useful for point-of-care testing (POCT).

Predictable Locations Aid Early Object Name Learning

PubMed Central

Benitez, Viridiana L.; Smith, Linda B.

2012-01-01

Expectancy-based localized attention has been shown to promote the formation and retrieval of multisensory memories in adults. Three experiments show that these processes also characterize attention and learning in 16- to 18- month old infants and, moreover, that these processes may play a critical role in supporting early object name learning. The three experiments show that infants learn names for objects when those objects have predictable rather than varied locations, that infants who anticipate the location of named objects better learn those object names, and that infants integrate experiences that are separated in time but share a common location. Taken together, these results suggest that localized attention, cued attention, and spatial indexing are an inter-related set of processes in young children that aid in the early building of coherent object representations. The relevance of the experimental results and spatial attention for everyday word learning are discussed. PMID:22989872

77 FR 9876 - Proposed Modification of VOR Federal Airways V-10, V-12, and V-508 in the Vicinity of Olathe, KS

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-21

... (OJC) VOR/DME navigation aid located on the Johnson County Executive Airport, Olathe, KS, due to poor performance of the navigation aid. The OJC VOR/DME performs poorly due to suburban encroachment into the...

First Steps in Government Documents: A Basic Guide.

ERIC Educational Resources Information Center

Sears, Jean L.; Moody, Marilyn K.

Designed to aid users in locating materials in the government documents department at Miami University in Oxford Ohio, this guide contains general information on the documents collection, a floor plan of the documents department, an introduction to U.S. government document finding aids, an introduction to U.S. Congressional and legislative…

Robot-aided assessment of lower extremity functions: a review.

PubMed

Maggioni, Serena; Melendez-Calderon, Alejandro; van Asseldonk, Edwin; Klamroth-Marganska, Verena; Lünenburger, Lars; Riener, Robert; van der Kooij, Herman

2016-08-02

The assessment of sensorimotor functions is extremely important to understand the health status of a patient and its change over time. Assessments are necessary to plan and adjust the therapy in order to maximize the chances of individual recovery. Nowadays, however, assessments are seldom used in clinical practice due to administrative constraints or to inadequate validity, reliability and responsiveness. In clinical trials, more sensitive and reliable measurement scales could unmask changes in physiological variables that would not be visible with existing clinical scores.In the last decades robotic devices have become available for neurorehabilitation training in clinical centers. Besides training, robotic devices can overcome some of the limitations in traditional clinical assessments by providing more objective, sensitive, reliable and time-efficient measurements. However, it is necessary to understand the clinical needs to be able to develop novel robot-aided assessment methods that can be integrated in clinical practice.This paper aims at providing researchers and developers in the field of robotic neurorehabilitation with a comprehensive review of assessment methods for the lower extremities. Among the ICF domains, we included those related to lower extremities sensorimotor functions and walking; for each chapter we present and discuss existing assessments used in routine clinical practice and contrast those to state-of-the-art instrumented and robot-aided technologies. Based on the shortcomings of current assessments, on the identified clinical needs and on the opportunities offered by robotic devices, we propose future directions for research in rehabilitation robotics. The review and recommendations provided in this paper aim to guide the design of the next generation of robot-aided functional assessments, their validation and their translation to clinical practice.

Context-Aided Tracking with Adaptive Hyperspectral Imagery

DTIC Science & Technology

2011-06-01

narrow spectral bands (e). . . . . . . . . . . . . . . . . . . . . 14 ix Figure Page 2.2. An illustration of a small portion of a digital micromirror ...incorporates two light paths: imaging and spectroscopy. Each pixel is steered towards a light path indepen- dently via the digital micromirror device (DMD...With the advent of digital micromirror device (DMD) arrays (DMA), the Rochester Institute of Technology Multi-Object Spectrometer (RITMOS) [36

Aids to Computer-Based Multimedia Learning: A Comparison of Human Tutoring and Computer Support

ERIC Educational Resources Information Center

Rodicio, H. Garcia; Sanchez, E.

2012-01-01

Learners are usually provided with support devices because they find it difficult to learn from multimedia presentations. A key question, with no clear answer so far, is how best to present these support devices. One possibility is to insert them into the multimedia presentation (canned support), while another is to have a human agent provide them…

Use of a Video Assistive Device in a University Course in Laboratory Science: A Case Study

ERIC Educational Resources Information Center

Cole, Ryan A.; Slavin, Alan J.

2013-01-01

This article describes a case study involving an assistive device that aided a student with low vision registered in the introductory physics course at Trent University in the fall of 2009. His Snellen visual acuity fluctuated significantly, with an average acuity of about 20/400. This low acuity presented obvious difficulties for him with the…

Computational modeling of direct neuronal recruitment during intracortical microstimulation in somatosensory cortex.

PubMed

Overstreet, C K; Klein, J D; Helms Tillery, S I

2013-12-01

Electrical stimulation of cortical tissue could be used to deliver sensory information as part of a neuroprosthetic device, but current control of the location, resolution, quality, and intensity of sensations elicited by intracortical microstimulation (ICMS) remains inadequate for this purpose. One major obstacle to resolving this problem is the poor understanding of the neural activity induced by ICMS. Even with new imaging methods, quantifying the activity of many individual neurons within cortex is difficult. We used computational modeling to examine the response of somatosensory cortex to ICMS. We modeled the axonal arbors of eight distinct morphologies of interneurons and seven types of pyramidal neurons found in somatosensory cortex and identified their responses to extracellular stimulation. We then combined these axonal elements to form a multi-layered slab of simulated cortex and investigated the patterns of neural activity directly induced by ICMS. Specifically we estimated the number, location, and variety of neurons directly recruited by stimulation on a single penetrating microelectrode. The population of neurons activated by ICMS was dependent on both stimulation strength and the depth of the electrode within cortex. Strikingly, stimulation recruited interneurons and pyramidal neurons in very different patterns. Interneurons are primarily recruited within a dense, continuous region around the electrode, while pyramidal neurons were recruited in a sparse fashion both near the electrode and up to several millimeters away. Thus ICMS can lead to an unexpectedly complex spatial distribution of firing neurons. These results lend new insights to the complexity and range of neural activity that can be induced by ICMS. This work also suggests mechanisms potentially responsible for the inconsistency and unnatural quality of sensations initiated by ICMS. Understanding these mechanisms will aid in the design of stimulation that can be used to generate effective sensory feedback for neuroprosthetic devices.

A voice-input voice-output communication aid for people with severe speech impairment.

PubMed

Hawley, Mark S; Cunningham, Stuart P; Green, Phil D; Enderby, Pam; Palmer, Rebecca; Sehgal, Siddharth; O'Neill, Peter

2013-01-01

A new form of augmentative and alternative communication (AAC) device for people with severe speech impairment-the voice-input voice-output communication aid (VIVOCA)-is described. The VIVOCA recognizes the disordered speech of the user and builds messages, which are converted into synthetic speech. System development was carried out employing user-centered design and development methods, which identified and refined key requirements for the device. A novel methodology for building small vocabulary, speaker-dependent automatic speech recognizers with reduced amounts of training data, was applied. Experiments showed that this method is successful in generating good recognition performance (mean accuracy 96%) on highly disordered speech, even when recognition perplexity is increased. The selected message-building technique traded off various factors including speed of message construction and range of available message outputs. The VIVOCA was evaluated in a field trial by individuals with moderate to severe dysarthria and confirmed that they can make use of the device to produce intelligible speech output from disordered speech input. The trial highlighted some issues which limit the performance and usability of the device when applied in real usage situations, with mean recognition accuracy of 67% in these circumstances. These limitations will be addressed in future work.