Results of borehole geophysical logging and aquifer-isolation tests conducted in the John Wagner and Sons, Inc. former production well, Ivyland, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.

1997-01-01

A suite of borehole geophysical logs and heat-pulse-flowmeter measurements run in the former production well at the John Wagner and Sons, Inc. plant indicate two zones of borehole flow. In the upper part of the well, water enters the borehole through a fracture at 90 ft (feet) below floor level, moves upward, and exits the borehole through a fracture at 72 ft below floor level. Water also enters the borehole through fractures at 205-213, 235, and 357 ft below floor level; moves downward; and exits the borehole through fractures at 450-459, 468-470, and 483-490 ft below floor level. Five zones were selected for aquifer-isolation (packer) tests on the basis of borehole geophysical logs. The zones were isolated using a straddle-packer assembly. The lowermost three zones (below 248, 223 to 248, and 198 to 223 ft below floor level) were hydraulically isolated from zones above and below. Specific capacities were 0.12, 0.034, and 0.15 gallons per minute per foot, respectively. The hydrograph from zone 2 (223 to 248 ft below floor level) showed interference from a nearby pumping well. For the upper two zones (81 to 106 and 57 to 81 ft below floor level), similar drawdowns in the isolated zone and the zones above and below the isolated zone indicate that these fractures are hydraulically connected outside the borehole in the unconfined part of the Stockton Formation. The specific capacity of zones 4 and 5 are similar—0.82 and 0.61, respectively.

Results of borehole geophysical logging and hydraulic tests conducted in Area D supply wells, former U.S. Naval Air Warfare Center, Warminster, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.; Grazul, Kevin E.

1998-01-01

Borehole geophysical logging, aquifer tests, and aquifer-isolation (packer) tests were conducted in four supply wells at the former U.S. Naval Air Warfare Center (NAWC) in Warminster, PA, to identify the depth and yield of water-bearing zones, occurrence of borehole flow, and effect of pumping on nearby wells. The study was conducted as part of an ongoing evaluation of ground-water contamination at the NAWC. Caliper, natural-gamma, single-point resistance, fluid resistivity, and fluid temperature logs and borehole television surveys were run in the supply wells, which range in depth from 242 to 560 ft (feet). Acoustic borehole televiewer and borehole deviation logs were run in two of the wells. The direction and rate of borehole-fluid movement under non-pumping conditions were measured with a high-resolution heatpulse flowmeter. The logs were used to locate water-bearing fractures, determine probable zones of vertical borehole-fluid movement, and determine the depth to set packers. An aquifer test was conducted in each well to determine open-hole specific capacity and the effect of pumping the open borehole on water levels in nearby wells. Specific capacities ranged from 0.21 to 1.7 (gal/min)/ft (gallons per minute per foot) of drawdown. Aquifer-isolation tests were conducted in each well to determine depth-discrete specific capacities and to determine the effect of pumping an individual fracture or fracture zone on water levels in nearby wells. Specific capacities of individual fractures and fracture zones ranged from 0 to 2.3 (gal/min)/ft. Most fractures identified as water-producing or water-receiving zones by borehole geophysical methods produced water when isolated and pumped. All hydrologically active fractures below 250 ft below land surface were identified as water-receiving zones and produced little water when isolated and pumped. In the two wells greater then 540 ft deep, downward borehole flow to the deep water-receiving fractures is caused by a large difference in head (as much as greater then 49 ft) between water-bearing fractured in the upper and lower part of the borehole. Vertical distribution of specific capacity between land surface and 250 ft below land surface is not related to depth.

Precipitation estimation in mountainous terrain using multivariate geostatistics. Part I: structural analysis

USGS Publications Warehouse

Hevesi, Joseph A.; Istok, Jonathan D.; Flint, Alan L.

1992-01-01

Values of average annual precipitation (AAP) are desired for hydrologic studies within a watershed containing Yucca Mountain, Nevada, a potential site for a high-level nuclear-waste repository. Reliable values of AAP are not yet available for most areas within this watershed because of a sparsity of precipitation measurements and the need to obtain measurements over a sufficient length of time. To estimate AAP over the entire watershed, historical precipitation data and station elevations were obtained from a network of 62 stations in southern Nevada and southeastern California. Multivariate geostatistics (cokriging) was selected as an estimation method because of a significant (p = 0.05) correlation of r = .75 between the natural log of AAP and station elevation. A sample direct variogram for the transformed variable, TAAP = ln [(AAP) 1000], was fitted with an isotropic, spherical model defined by a small nugget value of 5000, a range of 190 000 ft, and a sill value equal to the sample variance of 163 151. Elevations for 1531 additional locations were obtained from topographic maps to improve the accuracy of cokriged estimates. A sample direct variogram for elevation was fitted with an isotropic model consisting of a nugget value of 5500 and three nested transition structures: a Gaussian structure with a range of 61 000 ft, a spherical structure with a range of 70 000 ft, and a quasi-stationary, linear structure. The use of an isotropic, stationary model for elevation was considered valid within a sliding-neighborhood radius of 120 000 ft. The problem of fitting a positive-definite, nonlinear model of coregionalization to an inconsistent sample cross variogram for TAAP and elevation was solved by a modified use of the Cauchy-Schwarz inequality. A selected cross-variogram model consisted of two nested structures: a Gaussian structure with a range of 61 000 ft and a spherical structure with a range of 190 000 ft. Cross validation was used for model selection and for comparing the geostatistical model with six alternate estimation methods. Multivariate geostatistics provided the best cross-validation results.

Geopressured-geothermal test of the EDNA Delcambre No. 1 well, Vermilion Parish, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wieland, D.R.; Meriwether, J.

1977-11-16

Two sand intervals, Sand No. 3 and Sand No. 1, were independently tested during our program. Sand No. 3 was the deepeer zone and was tested first. A gamma ray--neutron log of these zones, and the intervals perforated, are shown. The gamma ray log run in 1968 showed Sand No. 1 to be a fairly uniform section with few shale breaks and our original plans were to perforate the entire interval. After obtaining the more recent GR log big shale breaks were shown to exist throughout the zone, so a smaller interval was selected. A net sand thickness of 48more » ft. was used for Sand No. 3 and 30 ft. for Sand No. 1. There was no data available to indicate whether these zones became thicker or thinner away from the wellbore; therefore, these values were used as net thickness in the reservoir calculations. The procedure used to perforate the two sands were different. Both were perforated with 0.33 inch jets at a density of 4 shots per foot; however, Sand No. 3 was perforated in two runs using a stand-off gun, whereas Sand No. 1 was perforated in one run using a centralized gun with the jet density being 4 shots per foot but oriented alternately at 180 degrees.« less

β-delayed γ decay of 20Mg and the 19Ne(p , γ) 20 Na breakout reaction in Type I X-ray bursts

NASA Astrophysics Data System (ADS)

Glassman, B. E.; Pérez-Loureiro, D.; Wrede, C.; Allen, J.; Bardayan, D. W.; Bennett, M. B.; Brown, B. A.; Chipps, K. A.; Febbraro, M.; Friedman, M.; Fry, C.; Hall, M. R.; Hall, O.; Liddick, S. N.; O'Malley, P.; Ong, W. J.; Pain, S. D.; Prokop, C.; Schwartz, S. B.; Shidling, P.; Sims, H.; Thompson, P.; Zhang, H.

2018-03-01

Certain astrophysical environments such as thermonuclear outbursts on accreting neutron stars (Type-I X-ray bursts) are hot enough to allow for breakout from the Hot CNO hydrogen burning cycles to the rapid proton capture (rp) process. An important breakout reaction sequence is 15O(α,γ)19Ne(p,γ)20Na and the 19Ne(p,γ)20Na reaction rate is expected to be dominated by a single resonance at 457 keV above the proton threshold in 20Na. The resonance strength and, hence, reaction rate depends strongly on whether this 20Na state at an excitation energy of 2647 keV has spin and parity of 1+ or 3+. Previous 20Mg (Jπ =0+) β+ decay experiments have relied almost entirely on searches for β-delayed proton emission from this resonance in 20Na to limit the log ft value and, hence, Jπ. However there is a non-negligible γ-ray branch expected that must also be limited experimentally to determine the log ft value and constrain Jπ. We have measured the β-delayed γ decay of 20Mg to complement previous β-delayed proton decay work and provide the first complete limit based on all energetically allowed decay channels through the 2647 keV state. Our limit confirms that a 1+ assignment for this state is highly unlikely.

Site Report for USGS Test Holes Drilled at Cape Charles, Northampton County, Virginia, in 2004

USGS Publications Warehouse

Gohn, Gregory S.; Sanford, Ward E.; Powars, David S.; Horton, J. Wright; Edwards, Lucy E.; Morin, Roger H.; Self-Trail, Jean M.

2007-01-01

The U.S. Geological Survey drilled two test holes near Cape Charles, Virginia, during May and June 2004, as part of an investigation of the buried, late Eocene Chesapeake Bay impact structure. The first hole is designated as the USGS-Sustainable Technology Park test hole #1 (USGS-STP1). This test hole was abandoned at a depth of 300 ft; cuttings samples were collected, but no cores or geophysical logs were acquired. The second hole is designated as the USGS-Sustainable Technology Park test hole #2 (USGS-STP2). This test hole was drilled to a depth of 2,699 ft. Cores were collected between depths of 1,401.7 ft and 1,420.7 ft and between 2,440.0 ft and 2,699.0 ft. Cuttings samples were collected from the uncored intervals below 280-ft depth. Interim sets of geophysical logs were acquired during the drilling operation, and one final set was acquired at the end of drilling. Two wells were installed in the USGS-STP2 test hole. The deep well (designated 62G-24) was screened between 2,260 ft and 2,280 ft, and the shallow well (designated 62G-25) was screened between 1,360 ft and 1,380 ft. Ground-water salinities stabilized at 40 parts per thousand for the deep well and 20 parts per thousand for the shallow well. The geologic section encountered in the test holes consists of three main units: (1) Eocene, Oligocene, Miocene, Pliocene, and Pleistocene sands and clays are present between land surface and a depth of 1,163 ft; (2) sediment-clast breccias of the impact structure are present between depths of 1,163 ft and 2,150 ft; and (3) crystalline-clast breccias and cataclastic gneiss of the impact structure are present between depths of 2,150 ft and 2,699 ft.

Effects of electrolyzed oxidizing water on reducing Listeria monocytogenes contamination on seafood processing surfaces.

PubMed

Liu, Chengchu; Duan, Jingyun; Su, Yi-Cheng

2006-02-15

The effects of electrolyzed oxidizing (EO) water on reducing Listeria monocytogenes contamination on seafood processing surfaces were studied. Chips (5 x 5 cm(2)) of stainless steel sheet (SS), ceramic tile (CT), and floor tile (FT) with and without crabmeat residue on the surface were inoculated with L. monocytogenes and soaked in tap or EO water for 5 min. Viable cells of L. monocytogenes were detected on all chip surfaces with or without crabmeat residue after being held at room temperature for 1 h. Soaking contaminated chips in tap water resulted in small-degree reductions of the organism (0.40-0.66 log cfu/chip on clean surfaces and 0.78-1.33 log cfu/chip on dirty surfaces). Treatments of EO water significantly (p<0.05) reduced L. monocytogenes on clean surfaces (3.73 log on SS, 4.24 log on CT, and 5.12 log on FT). Presence of crabmeat residue on chip surfaces reduced the effectiveness of EO water on inactivating Listeria cells. However, treatments of EO water also resulted in significant reductions of L. monocytogenes on dirty surfaces (2.33 log on SS and CT and 1.52 log on FT) when compared with tap water treatments. The antimicrobial activity of EO water was positively correlated with its chlorine content. High oxidation-reduction potential (ORP) of EO water also contributed significantly to its antimicrobial activity against L. monocytogenes. EO water was more effective than chlorine water on inactivating L. monocytogenes on surfaces and could be used as a chlorine alternative for sanitation purpose. Application of EO water following a thorough cleaning process could greatly reduce L. monocytogenes contamination in seafood processing environments.

Phthalates and thyroid function in preschool age children: Sex specific associations.

PubMed

Morgenstern, Rachelle; Whyatt, Robin M; Insel, Beverly J; Calafat, Antonia M; Liu, Xinhua; Rauh, Virginia A; Herbstman, Julie; Bradwin, Gary; Factor-Litvak, Pam

2017-09-01

Research relating either prenatal or concurrent measures of phthalate exposure to thyroid function in preschool children is inconclusive. In a study of inner-city mothers and their children, metabolites of di-n-butyl phthalate, butylbenzyl phthalate, di-isobutyl phthalate, di(2-ethylhexyl) phthalate, and diethyl phthalate were measured in a spot urine sample collected from women in late pregnancy and from their children at age 3years. We measured children's serum free thyroxine (FT4) and thyroid stimulating hormone (TSH) at age 3. Linear regression models were used to investigate the associations between phthalate metabolites, measured in maternal urine during late pregnancy and measured in child urine at age 3 and thyroid function measured at age 3. Mean concentrations (ranges) were 1.42ng/dL (1.02-2.24) for FT4, and 2.62uIU/mL (0.61-11.67) for TSH. In the children at age 3, among girls, FT4 decreased with increasing log e mono-n-butyl phthalate [estimated b=-0.06; 95% CI: (-0.09, -0.02)], log e mono-isobutyl phthalate [b=-0.05; 95% CI: (-0.09, -0.01)], log e monoethyl phthalate [b=-0.04; 95% CI: (-0.07, -0.01)], and log e mono(2-ethyl-5-hydroxyhexyl) phthalate [b=-0.04; 95% CI: (-0.07, -0.003)] and log e mono(2-ethyl-5-oxy-hexyl) phthalate [b=-0.04; 95% CI: (-0.07, -0.004)]. In contrast, among boys, we observed no associations between FT4 and child phthalate metabolites at age 3. On the other hand, in late gestation, FT4 increased with increasing log e mono-(2-ethylhexyl) phthalate [estimated b=0.04; 95% CI: (0.02, 0.06)] and no sex difference was observed. We found no associations between phthalate biomarkers measured in either the child or prenatal samples and TSH at age 3. The data show inverse and sex specific associations between specific phthalate metabolites measured in children at age 3 and thyroid function in preschool children. These results may provide evidence for the hypothesis that reductions in thyroid hormones mediate associations between early life phthalate exposure and child cognitive outcomes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Geohydrology of the Vamoosa-Ada aquifer east-central Oklahoma with a section on chemical quality of water

USGS Publications Warehouse

D'Lugosz, Joseph J.; McClaflin, Roger G.; Marcher, Melvin V.

1986-01-01

The Vamoosa-Ada aquifer, which underlies an area of about 2,320 mi2, consists principally of the Vamoosa Formation and the overlying Ada Group of Pennsylvanian age. Rocks comprising the aquifer were deposited in a nearshore environment ranging from marine on the west to nonmarine on the east. Because of changes in depositional environments with time and from place to place, the aquifer is a complex sequence of fine- to very fine-grained sandstone, siltstone, shale, and conglomerate, with interbedded very thin limestone. The aggregate thickness of water-bearing sandstones is greatest south of the Cimarron River, where it reaches a maximum of 550 ft in the vicinity of Seminole. North of the Cimarron River, the average aggregate thickness of the sandstones is about 100 ft, but locally it may be as much as 200 ft. Transmissivity values derived from seven aquifer tests made for this study range from 70 to 490 ft2 per day; values decrease from south to north with decreasing sandstone thickness. Hydraulic-conductivity values range from 2 to 4 ft per day. Storage coefficients for the confined part of the aquifer, as determined from four aquifer tests made during 1944, have an average value of 0.0002. The average storage coefficient for the unconfined part of the aquifer is estimated at 0.12, based on an analysis of geophysical logs and grain-size data. The specific capacity of wells tested is generally less than 1 gallon per minute per foot of drawdown. An approximate hydrologic budget for the aquifer for 1975 gives values, in acre-feet per year, of 93,000 for recharge, 233,000 for runoff, and 2,003,000 for evapotranspiration. The total of these values is almost equal to the average annual precipitation of 2,330,000 acre-ft per year. The estimated amount of water containing a maximum of 1,500 milligrams per liter of dissolved solids stored in the aquifer is estimated at 60 million acre-ft. Of this amount, an estimated 36 million acre-ft is available for use. The quality of water in the Vamoosa-Ada aquifer generally is suitable for municipal, domestic, and stock use. Of 55 water samples analyzed in the laboratory, about 75 percent were of the sodium bicarbonate or sodium calcium bicarbonate type; the remainder were of the sodium sulfate, calcium sulfate, sodium chloride, or indeterminate types. Laboratory and on-site chemical-quality data indicate that mineralization of both ground and surface waters is greater than normal in some areas. Water samples from 7 wells and 12 stream sites had concentrations of bromide exceeding 1 milligram per liter; the only known source of bromide in the area is brine associated with petroleum production.

How PEMEX engineered a deep well completion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Antimo A., J.C.

1971-09-01

Completion and testing of Petroleos Mexicano's W. Reynosa Well No. 1 in the NE. Frontier District south of the Texas border required engineering innovation to combat the 375/sup 0/F temperatures and pressures near 18,000 psi. Drilled to nearly 18,000 ft, the well was completed and tested below 17,000 ft. Completion plans were designed to determine the economic importance of the reservoir and to provide information and experience in planning future completions to 20,000 ft and deeper. Interval selection was based in part on data acquired during drilling, including lithology, geologic age, rock characteristics, and sensitivity to damage caused by drillingmore » fluids. A set of logs was obtained and evaluated by computer in correlation with mud-log and pressure data. The logs also were correlated with logs from other wells in the area. Pressure gradients in the Reynosa field indicated the possibility of pressures on the order of 10,000 psi, and required the use of specially designed valves rated to 20,000 psi, in conjunction with a casinghead that would permit drilling to the projected depth. A choke manifold consisted of an interchangeable, manually operated positive choke and a set of automatic adjustable chokes. Well conditioning, including cementing, perforating, and well plugging are described.« less

Characterization of a remotely intersected set of hydraulic fractures: Results of intersection well no. 1-B, GRI/DOE multi-site project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Branagan, P.T.; Peterson, R.E.; Warpinski, N.R.

A deviated observation or {open_quotes}intersection{close_quotes} well (IW 1-B) was drilled, cored, logged and tested through an area in a fluvial sandstone reservoir that had previously been hydraulically fractured. The point of intersection with the fractured interval was located 126 ft from the fracture well along one wing of the fracture(s) at a measured depth of 4,675 ft. Direct observations from core and borehole imagery logs in IW 1-B indicate that a total of 11 far-field vertical fractures were created. Clustered in a narrow 2.6-ft-wide interval, these 11 fractures are the direct result of 6 experimental fracture treatments executed in themore » distant frac well over a 4-month period. Diagnostic data acquired through IW I-B included direct core observations and measurements, borehole log imagery, gamma ray (GR) tracer identification, well-to-well pressure transient and fracture conductivity tests, and production logging surveys. The explicit intent in the emplacement of IW 1-B was to provide direct observations and information to characterize the hydraulic fracture(s) in support of a remote-sensing fracture diagnostic program that included microseismic monitoring and inclinometer measurements.« less

Maternal Urinary Triclosan Concentration in Relation to Maternal and Neonatal Thyroid Hormone Levels: A Prospective Study.

PubMed

Wang, Xu; Ouyang, Fengxiu; Feng, Liping; Wang, Xia; Liu, Zhiwei; Zhang, Jun

2017-06-27

Triclosan (TCS) is a synthetic antibacterial chemical widely used in personal care products. TCS exposure has been associated with decreased thyroid hormone levels in animals, but human studies are scarce and controversial. We evaluated the association between maternal TCS exposure and thyroid hormone levels of mothers and newborns. TCS was measured by high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) in urine samples collected during gestational weeks 38.8±1.1 from 398 pregnant women in a prospective birth cohort enrolled in 2012-2013 in Shanghai, China. Maternal serum levels of free thyroxine (FT 4 ), thyroid-stimulating hormone (TSH), and thyroid peroxidase antibody (TPOAb) were obtained from medical records. Cord blood levels of free triiodothyronine (FT 3 ), FT 4 , TSH, and TPOAb were measured. Multiple linear and logistic regression models were used to examine the relationship between maternal urinary TCS and thyroid hormone levels. TCS was detectable (≥0.1 ng/mL) in 98.24% of maternal urine samples with tertile of urinary TCS levels: low (>0.1-2.75 μg/g.Cr), medium (2.75–9.78 μg/g.Cr), and high (9.78–427.38 μg/g.Cr). With adjustment for potential confounders, cord blood log(FT 3 )pmol/L concentration was 0.11 lower in newborns of mothers with medium and high urinary TCS levels compared with those with low levels. At third trimester, the high TCS concentration was associated with 0.03 [95% confidence interval (CI) −0.08, −0.02] lower maternal serum log(FT 4 )pmol/L, whereas the medium TCS concentration was associated with 0.15 (95% CI: −0.28, −0.03) lower serum log(TSH)mIU/L with adjustment for covariates. Our results suggest significant inverse associations between maternal urinary TCS and cord blood FT 3 as well as maternal blood FT 4 concentrations at third trimester. https://doi.org/10.1289/EHP500.

Green lumber grade yields from black cherry and red maple factory grade logs sawed at band and circular mills

Treesearch

Daniel A. Yaussy

1989-01-01

Multivariate regression models were developed to predict green board-foot yields (1 board ft. = 2.360 dm 3) for the standard factory lumber grades processed from black cherry (Prunus serotina Ehrh.) and red maple (Acer rubrum L.) factory grade logs sawed at band and circular sawmills. The models use log...

Spent Fuel Test-Climax: core logging for site investigation and instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilder, D.G.; Yow, J.L. Jr.; Thorpe, R.K.

1982-05-28

As an integral part of the Spent Fuel Test-Climax 5150 ft (1570 m) of granite core was obtained. This core was diamond drilled in various sizes, mainly 38-mm and 76-mm diameters. The core was teken with single tube core barrels and was unoriented. Techniques used to drill and log this core are discussed, as well as techniques to orient the core. Of the 5150 ft (1570 m) of core more than 3645 ft (1111 m) was retained and logged in some detail. As a result of the core logging, geologic discontinuities were identified, joint frequency and spacing characterized. Discontinuities identifiedmore » included several joint sets, shear zones and faults. Correlations based on coring along were generally found to be impossible, even for the more prominent features. The only feature properly correlated from the exploratory drilling was the fault system at the end of the facility, but it was not identified from the exploratory core as a fault. Identification of discontinuities was later helped by underground mapping that identified several different joint sets with different characteristics. It was found that joint frequency varied from 0.3 to 1.1 joint per foot of core for open fractures and from 0.3 to 3.3/ft for closed or healed fractures. Histograms of fracture spacing indicate that there is likely a random distribution of spacing superimposed upon uniformly spaced fractures. It was found that a low angle joint set had a persistent mean orientation. These joints were healed and had pervasive wall rock alteration which made identification of joints in this set possible. The recognition of a joint set with known attitude allowed orientation of much of the core. This orientation technique was found to be effective. 10 references, 25 figures, 4 tables.« less

Wood density-moisture profiles in old-growth Douglas-fir and western hemlock.

Treesearch

W.Y. Pong; Dale R. Waddell; Lambert Michael B.

1986-01-01

Accurate estimation of the weight of each load of logs is necessary for safe and efficient aerial logging operations. The prediction of green density (lb/ft3) as a function of height is a critical element in the accurate estimation of tree bole and log weights. Two sampling methods, disk and increment core (Bergstrom xylodensimeter), were used to measure the density-...

Log analysis of six boreholes in conjunction with geologic characterization above and on top of the Weeks Island salt dome

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.

1996-04-01

Six boreholes were drilled during the geologic characterization and diagnostics of the Weeks Island sinkhole that is over the two-tiered salt mine which was converted for oil storage by the US Strategic Petroleum Reserve. These holes were drilled to provide for geologic characterization of the Weeks Island Salt Dome and its overburden in the immediate vicinity of the sinkhole (mainly through logs and core); to establish a crosswell configuration for seismic tomography; to establish locations for hydrocarbon detection and tracer injection; and to Provide direct observations of sinkhole geometry and material properties. Specific objectives of the logging program were to:more » (1) identify the top of and the physical state of the salt dome; (2) identify the water table; (3) obtain a relative salinity profile in the aquifer within the alluvium, which ranges from the water table directly to the top of the Weeks Island salt dome; and (4) identify a reflecting horizon seen on seismic profiles over this salt dome. Natural gamma, neutron, density, sonic, resistivity and caliper logs were run. Neutron and density logs were run from inside the well casing because of the extremely unstable condition of the deltaic alluvium overburden above the salt dome. The logging program provided important information about the salt dome and the overburden in that (1) the top of the salt dome was identified at {approximately}189 ft bgl (103 ft msl), and the top of the dome contains relatively few fractures; (2) the water table is approximately 1 ft msl, (3) this aquifer appears to become steadily more saline with depth; and (4) the water saturation of much of the alluvium over the salt dome is shown to be influenced by the prevalent heavy rainfall. This logging program, a part of the sinkhole diagnostics, provides unique information about this salt dome and the overburden.« less

Hydrologeology and water quality of the Floridan aquifer system and effect of Lower Floridan aquifer pumping on the Upper Floridan aquifer, Pooler, Chatham County, Georgia, 2011–2012

USGS Publications Warehouse

Gonthier, Gerard

2012-01-01

Two test wells were completed in Pooler, Georgia, in 2011 to investigate the potential of using the Lower Floridan aquifer as a source of water for municipal use. One well was completed in the Lower Floridan aquifer at a depth of 1,120 feet (ft) below land surface; the other well was completed in the Upper Floridan aquifer at a depth of 486 ft below land surface. At the Pooler test site, the U.S. Geological Survey performed flowmeter surveys, packer-isolated slug tests within the Lower Floridan confining unit, slug tests of the entire Floridan aquifer system, and aquifer tests of the Upper and Lower Floridan aquifers. Drill cuttings, geophysical logs, and borehole flowmeter surveys indicate that the Upper Floridan aquifer extends 333 –515 ft below land surface, the Lower Floridan confining unit extends 515–702 ft below land surface, and the Lower Floridan aquifer extends 702–1,040 ft below land surface. Flowmeter surveys indicate that the Upper Floridan aquifer contains two water-bearing zones at depth intervals of 339 –350 and 375–515 ft; the Lower Floridan confining unit contains one zone at a depth interval of 550–620 ft; and the Lower Floridan aquifer contains five zones at depth intervals of 702–745, 745–925, 925–984, 984–1,015, and 1,015–1,040 ft. Flowmeter testing of the test borehole open to the entire Floridan aquifer system indicated that the Upper Floridan aquifer contributed 92.4 percent of the total flow rate of 708 gallons per minute; the Lower Floridan confining unit contributed 3.0 percent; and the Lower Floridan aquifer contributed 4.6 percent. Horizontal hydraulic conductivity of the Lower Floridan confining unit derived from slug tests within three packer-isolated intervals ranged from 0.5 to 10 feet per day (ft/d). Aquifer-test analyses yielded values of transmissivity for the Upper Floridan aquifer, Lower Floridan confining unit, and the Lower Floridan aquifer of 46,000, 700, and 4,000 feet squared per day (ft2/d), respectively. Horizontal hydraulic conductivity of 4 ft/d for the Lower Floridan confining unit, derived from aquifer-test analyses, is near the midrange for values derived from packer-isolated slug tests. The transmissivity of the entire Floridan aquifer system derived from aquifer-test analyses totals about 51,000 ft2/d, similar to the value of 58,000 ft2/d derived from open slug tests on the entire Floridan aquifer system. Water-level data for each aquifer test were filtered for external influences such as barometric pressure, earth-tide effects, and long-term trends to enable detection of small (less than 1 foot) water-level responses to aquifer-test pumping. During the 72-hour aquifer test of pumping the Lower Floridan aquifer, a drawdown response of 51.7 ft was observed in the Lower Floridan pumped well and a drawdown response of 0.9 foot was observed in the Upper Floridan observation well located 85 ft from the pumped well.

Completion summary for boreholes TAN-2271 and TAN‑2272 at Test Area North, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Twining, Brian V.; Bartholomay, Roy C.; Hodges, Mary K.V.

2016-06-30

In 2015, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, drilled and constructed boreholes TAN-2271 and TAN-2272 for stratigraphic framework analyses and long-term groundwater monitoring of the eastern Snake River Plain aquifer at the Idaho National Laboratory in southeast Idaho. Borehole TAN-2271 initially was cored to collect continuous geologic data, and then re-drilled to complete construction as a monitor well. Borehole TAN-2272 was partially cored between 210 and 282 feet (ft) below land surface (BLS) then drilled and constructed as a monitor well. Boreholes TAN-2271 and TAN-2272 are separated by about 63 ft and have similar geologic layers and hydrologic characteristics based on geologic, geophysical, and aquifer test data collected. The final construction for boreholes TAN-2271 and TAN-2272 required 10-inch (in.) diameter carbon-steel well casing and 9.9-in. diameter open-hole completion below the casing to total depths of 282 and 287 ft BLS, respectively. Depth to water is measured near 228 ft BLS in both boreholes. Following construction and data collection, temporary submersible pumps and water-level access lines were placed to allow for aquifer testing, for collecting periodic water samples, and for measuring water levels.Borehole TAN-2271 was cored continuously, starting at the first basalt contact (about 33 ft BLS) to a depth of 284 ft BLS. Excluding surface sediment, recovery of basalt and sediment core at borehole TAN-2271 was better than 98 percent. Based on visual inspection of core and geophysical data, material examined from 33 to 211ft BLS primarily consists of two massive basalt flows that are about 78 and 50 ft in thickness and three sediment layers near 122, 197, and 201 ft BLS. Between 211 and 284 ft BLS, geophysical data and core material suggest a high occurrence of fractured and vesicular basalt. For the section of aquifer tested, there are two primary fractured aquifer intervals: the first between 235 and 255 ft BLS and the second between 272 and 282 ft BLS. Basalt texture for borehole TAN-2271 generally was described as aphanitic, phaneritic, and porphyritic. Sediment layers, starting near 122 ft BLS, generally were composed of fine-grained sand and silt with a lesser amount of clay. Basalt flows generally ranged in thickness from 2 to 78 ft and varied from highly fractured to dense with high to low vesiculation. Geophysical data and limited core material collected from TAN-2272 show similar lithologic sequences to those reported for TAN-2271.Geophysical and borehole video logs were collected during certain stages of the drilling and construction process at boreholes TAN-2271 and TAN-2272. Geophysical logs were examined synergistically with available core material to confirm geologic and hydrologic similarities and suggest possible fractured network interconnection between boreholes TAN-2271 and TAN-2272. Natural gamma log measurements were used to assess the completeness of the vapor port lines behind 10-in. diameter well casing. Electromagnetic flow meter results were used to identify downward flow conditions that exist for boreholes TAN-2271 and TAN-2272. Furthermore, gyroscopic deviation measurements were used to measure horizontal and vertical displacement at all depths in boreholes TAN-2271 and TAN-2272.After borehole construction was completed, single‑well aquifer tests were done within wells TAN-2271 and TAN‑2272 to provide estimates of transmissivity and hydraulic conductivity. The transmissivity and hydraulic conductivity were estimated for the pumping well and observation well during the aquifer tests conducted on August 25 and August 27, 2015. Estimates for transmissivity range from 4.1 . 103 feet squared per day (ft2/d) to 8.1 . 103 ft2/d; estimates for hydraulic conductivity range from 5.8 to 11.5 feet per day (ft/d). Both TAN-2271 and TAN‑2272 show sustained pumping rates of about 30 gallons per minute (gal/min) with measured drawdown in the pumping well of 1.96 ft and 1.14 ft, respectively. The transmissivity estimates for wells tested were within the range of values determined from previous aquifer tests in other wells near Test Area North.Groundwater samples were collected from both wells and were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Groundwater samples for most of the inorganic constituents showed similar water chemistry in both wells. Groundwater samples for strontium-90, trichloroethene, and vinyl chloride exceeded maximum contaminant levels for public drinking water supplies in one or both wells.

Construction diagrams, geophysical logs, and lithologic descriptions for boreholes USGS 126a, 126b, 127, 128, 129, 130, 131, 132, 133, and 134, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Twining, Brian V.; Hodges, Mary K.V.; Orr, Stephanie

2008-01-01

This report summarizes construction, geophysical, and lithologic data collected from ten U.S. Geological Survey (USGS) boreholes completed between 1999 nd 2006 at the Idaho National Laboratory (INL): USGS 126a, 126b, 127, 128, 129, 130, 131, 132, 133, and 134. Nine boreholes were continuously cored; USGS 126b had 5 ft of core. Completion depths range from 472 to 1,238 ft. Geophysical data were collected for each borehole, and those data are summarized in this report. Cores were photographed and digitally logged using commercially available software. Digital core logs are in appendixes A through J. Borehole descriptions summarize location, completion date, and amount and type of core recovered. This report was prepared by the USGS in cooperation with the U.S. Department of Energy (DOE).

Recognition and delineation of Paleokarst zones by the use of wireline logs in the bitumen-saturated upper Devonian Grosmont formation of Northeastern Alberta, Canada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dembicki, E.A.; Machel, H.G.

1996-05-01

The Upper Devonian Grosmont Formation in northeastern Alberta, Canada, is a shallow-marine carbonate platform complex that was subaerially exposed for hundreds of millions of years between the Mississippian(?) and Cretaceous. During this lengthy exposure period, an extensive karst system developed that is characterized by an irregular erosional surface, meter-size (several feet) dissolution cavities, collapse breccias, sinkholes, paleosols, and fractures. The karsted Grosmont Formation, which contains giant reserves of bitumen, sub-crops beneath Cretaceous clastic sediments of the giant Athabasca tar sands deposit. The paleokarst in the Grosmont Formation can be recognized on wireline logs in relatively nonargillaceous carbonate intervals (<30 APImore » units on the gamma-ray log) as excursions of the caliper log, off-scale neutron-density porosity readings, and severe cycle skipping of the acoustic log. The paleokarst is more prevalent in the upper units of the Grosmont Formation, and the effects of karstification decrease toward stratigraphically older and deeper units. The paleokarst usually occurs within 35 m (115 ft) of the erosional surface. The reservoir properties of the Grosmont Formation (e.g., thickness, porosity, permeability, and seal effectiveness) are significantly influenced by karstification. Depending upon the location, karstification has either benefited or degraded the reservoir characteristics. Benefits include porosity values greater than 40% (up to 100% in caverns) and permeability values of 30,000 md in severely fractured intervals. Detrimental reservoir characteristics include erosion, porosity and permeability reduction, and seal ineffectiveness.« less

Completion summary for borehole USGS 136 near the Advanced Test Reactor Complex, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Twining, Brian V.; Bartholomay, Roy C.; Hodges, Mary K.V.

2012-01-01

In 2011, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, cored and completed borehole USGS 136 for stratigraphic framework analyses and long-term groundwater monitoring of the eastern Snake River Plain aquifer at the Idaho National Laboratory. The borehole was initially cored to a depth of 1,048 feet (ft) below land surface (BLS) to collect core, open-borehole water samples, and geophysical data. After these data were collected, borehole USGS 136 was cemented and backfilled between 560 and 1,048 ft BLS. The final construction of borehole USGS 136 required that the borehole be reamed to allow for installation of 6-inch (in.) diameter carbon-steel casing and 5-in. diameter stainless-steel screen; the screened monitoring interval was completed between 500 and 551 ft BLS. A dedicated pump and water-level access line were placed to allow for aquifer testing, for collecting periodic water samples, and for measuring water levels.Geophysical and borehole video logs were collected after coring and after the completion of the monitor well. Geophysical logs were examined in conjunction with the borehole core to describe borehole lithology and to identify primary flow paths for groundwater, which occur in intervals of fractured and vesicular basalt.A single-well aquifer test was used to define hydraulic characteristics for borehole USGS 136 in the eastern Snake River Plain aquifer. Specific-capacity, transmissivity, and hydraulic conductivity from the aquifer test were at least 975 gallons per minute per foot, 1.4 × 105 feet squared per day (ft2/d), and 254 feet per day, respectively. The amount of measureable drawdown during the aquifer test was about 0.02 ft. The transmissivity for borehole USGS 136 was in the range of values determined from previous aquifer tests conducted in other wells near the Advanced Test Reactor Complex: 9.5 × 103 to 1.9 × 105 ft2/d.Water samples were analyzed for cations, anions, metals, nutrients, total organic carbon, volatile organic compounds, stable isotopes, and radionuclides. Water samples from borehole USGS 136 indicated that concentrations of tritium, sulfate, and chromium were affected by wastewater disposal practices at the Advanced Test Reactor Complex. Depth-discrete groundwater samples were collected in the open borehole USGS 136 near 965, 710, and 573 ft BLS using a thief sampler; on the basis of selected constituents, deeper groundwater samples showed no influence from wastewater disposal at the Advanced Test Reactor Complex.

Level II scour analysis for Bridge 48 (FFIETH00300048) on Town Highway 30, crossing Wanzer Brook, Fairfield, Vermont

USGS Publications Warehouse

Flynn, Robert H.; Boehmler, Erick M.

1997-01-01

This report provides the results of a detailed Level II analysis of scour potential at structure FFIETH00300048 on Town Highway 30 crossing Wanzer Brook, Fairfield, Vermont (figures 1–8). A Level II study is a basic engineering analysis of the site, including a quantitative analysis of stream stability and scour (U.S. Department of Transportation, 1993). Results of a Level I scour investigation also are included in Appendix E of this report. A Level I investigation provides a qualitative geomorphic characterization of the study site. Information on the bridge, gleaned from Vermont Agency of Transportation (VTAOT) files, was compiled prior to conducting Level I and Level II analyses and is found in Appendix D. The site is in the Green Mountain section of the New England physiographic province in northwestern Vermont. The 6.78-mi2 drainage area is in a predominantly rural and forested basin. In the vicinity of the study site, the surface cover upstream of the bridge and on the downstream right bank is primarily pasture. The downstream left bank is forested. In the study area, Wanzer Brook has an incised, straight channel with a slope of approximately 0.03 ft/ft, an average channel top width of 65 ft and an average bank height of 5 ft. The channel bed material is cobble with a median grain size (D50) of 111 mm (0.364 ft). The geomorphic assessment at the time of the Level I and Level II site visit on July 11, 1995, indicated that the reach was stable. The Town Highway 30 crossing of Wanzer Brook is a 31-ft-long, two-lane bridge consisting of one 28-foot steel-beam span (Vermont Agency of Transportation, written communication, March 8, 1995). The opening length of the structure parallel to the bridge face is 26 ft.The bridge is supported by vertical stone wall abutments with concrete caps and “kneewall” footings. The channel is skewed approximately 25 degrees to the opening while the measured opening-skew-to-roadway is 20 degrees. A scour hole 1.5 ft deeper than the mean thalweg depth was observed along the downstream left retaining wall (extended concrete footing) during the Level I assessment. It was also observed that the right abutment is undermined with a scour depth of 0.5 ft. The scour protection at the site was limited to four large boulders (type-4, less than 60 inches diameter) along the downstream right retaining wall. The channel under the bridge is a “corduroy” log mat floor composed of 13 logs which are parallel to the bridge face and extend from 5 ft under the bridge to the downstream bridge face. The most downstream log is approximately 0.3 to 0.4 ft higher than the other logs and controls flow at lower flows. Additional details describing conditions at the site are included in the Level II Summary and Appendices D and E. Scour depths and recommended rock rip-rap sizes were computed using the general guidelines described in Hydraulic Engineering Circular 18 (Richardson and others, 1995). Total scour at a highway crossing is comprised of three components: 1) long-term streambed degradation; 2) contraction scour (due to accelerated flow caused by a reduction in flow area at a bridge) and; 3) local scour (caused by accelerated flow around piers and abutments). Total scour is the sum of the three components. Equations are available to compute depths for contraction and local scour and a summary of the results of these computations follows. Contraction scour for all modelled flows ranged from 0.3 to 0.6 ft. The worst-case contraction scour occurred at the 500-year discharge. Abutment scour ranged from 14.1 to 16.0 ft at the left abutment and from 6.8 to 7.6 ft at the right abutment. The worst-case abutment scour occurred at the 500-year discharge. Additional information on scour depths and depths to armoring are included in the section titled “Scour Results”. Scoured-streambed elevations, based on the calculated scour depths, are presented in tables 1 and 2. A cross-section of the scour computed at the bridge is presented in figure 8. Scour depths were calculated assuming an infinite depth of erosive material and a homogeneous particle-size distribution. It is generally accepted that the Froehlich equation (abutment scour) gives “excessively conservative estimates of scour depths” (Richardson and others, 1995, p. 47). Usually, computed scour depths are evaluated in combination with other information including (but not limited to) historical performance during flood events, the geomorphic stability assessment, existing scour protection measures, and the results of the hydraulic analyses. Therefore, scour depths adopted by VTAOT may differ from the computed values documented herein.

Salt Interval Velocities vs Latitude in the Deepwater Gulf of Mexico: Keathley Canyon and Walker Ridge Areas

NASA Astrophysics Data System (ADS)

Cornelius, S.; Castagna, J. P.

2016-12-01

ABSTRACT A well log database of approximately 300 well logs from the Keathley Canyon and Walker Ridge areas of the Gulf of Mexico plus Mad Dog Field and Mission Deep Field in Green Canyon has been created for the purpose of building a geologically based 3D velocity model. While in the process of calibrating the finished velocity model, a scatter plot was made of all salt interval velocities versus latitude and an unexpected correlation was observed. Five different interval velocity zones have been identified with each having certain associated mineralogies within a latitude range. The salt interval velocity in the southern limits of the study area is higher than 15,000 ft/sec (4572 m/sec) due to the presence of gypsum. The northern most wells in the project area have anhydrite present inside the salt matrix such that their interval velocity can be as high as 18,535 ft/sec (5650 m/sec). In the mid-latitude zones, sylvite, siltstone, claystone, shale, tar and bitumen, with small traces of both anhydrite and gypsum, are found within the salt, yielding salt interval velocity variation from 14,388 ft/sec to 14,909 ft/sec (4386 m/sec to 4544 m/sec). The mineralogical content of the salt in each well was roughly estimated from mud logs and the corresponding interval velocities were determined from vertical seismic profiles, checkshot surveys, and sonic logs. Both geothermal gradients and overburden geopressure gradients between the mudline and the true vertical depth at well bottom calculated from this well database do not show the same correlation with latitude as the salt interval velocities. Mineralogical modeling of the salt composition using Hashin-Shtrikman bounds shows that these various inclusions within the salt matrix can be the cause of the observed variations in the salt interval velocities.

Mt, St. Helens, Mt. Adams, and Mt. Rainier, WA, USA

NASA Technical Reports Server (NTRS)

1992-01-01

This view of Mt. St. Helens (46.5N, 122.0W), taken 12 years after the volcanic eruption on 18 May 1980, in which the top 1300 ft. of the 9,677 ft. mountain was blown away, shows the rapid vegetation recovery within the blast area. Many fir trees have grown to heights of 20 ft. within the 150 square mile devastated area. Mt. Adams, an extinct volcano is just to the west and Mt. Rainier is to the north. Checkerboard logging can be seen throughout.

Roosevelt Hot Springs, Utah FORGE Stress Logging Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

McLennan, John

This spreadsheet consist of data and graphs from deep well 58-32 stress testing from 6900 - 7500 ft depth. Measured stress data were used to correct logging predictions of in situ stress. Stress plots shows pore pressure (measured during the injection testing), the total vertical in situ stress (determined from the density logging) and the total maximum and minimum horizontal stresses. The horizontal stresses were determined from the DSI (Dipole Sonic Imager) and corrected to match the direct measurements.

A Regional Groundwater Observatory to Enhance Analysis and Management of Water Resources

NASA Astrophysics Data System (ADS)

Yoder, A. M.; Maples, S.; Hatch, N. R.; Fogg, G. E.

2017-12-01

Timely, effective management of groundwater often does not happen because timely information on the state of the groundwater system is seldom available. A groundwater observatory for monitoring real-time groundwater level fluctuations is being developed in the American-Cosumnes groundwater system of Sacramento County, California. The observatory records the consequences of complex interplay between pumpage, recharge, drought, and floods in the context of a heterogeneous stratigraphic framework that has been extensively characterized with more than 1,100 well logs. Preliminary results show increases in recharge caused by removal of flood control levees to allow more frequent floodplain inundation as well as consequences of the 2012-16 drought followed by the wet winter of 2016-17. Comparison of recharge rates pre- and post-levee breach restoration show significant increases in recharge, despite the presence of fine-grained floodplain soils. Estimated total recharge corresponded closely with the frequency and magnitude of flood events in any given water year. The lowest value calculated for estimated recharge was from 2012-2013, 490 +/- 220 ac-ft (0.65 +/- 0.29 ac-ft per acre). The highest estimated recharge value calculated was for the 2015-2016 water year and was 3180 +/- 1430 ac-ft (2.83 +/- 1.27 ac-ft per acre). These preliminary numbers will be updated with more comprehensive estimates based on a full analysis of the 2016-17 data. The increase in data transfer efficiency afforded by the observatory can be widely used by the many parties reliant on Central Valley groundwater and can serve as a model for real-time data collection in support of California's Sustainable Groundwater Management Act, passed in 2014.

The Association Among Hypogonadism, Symptom Burden, and Survival in Male Patients with Advanced Cancer

PubMed Central

Dev, R; Hui, D; Del Fabbro, E; Delgado-Guay, MO; Sobti, N; Dalal, S; Bruera, E

2014-01-01

Background A high frequency of hypogonadism has been reported in male patients with advanced cancer. Objectives To evaluate the association among low testosterone, symptom burden and survival in cancer patients. Methods 119/131 (91%) consecutive male cancer patients had an endocrine evaluation of total/free/bioavailable testosterone (TT, FT, BT, respectively), high-sensitivity C-reactive protein (CRP), vitamin B12, thyroid stimulating hormone, 25-hydroxy vitamin D and cortisol levels when presenting with symptoms of fatigue and/or anorexia-cachexia. Symptoms were evaluated by the Edmonton Symptom Assessment Scale. We examined the correlation with Spearman test and survival with log rank test and Cox-regression analysis. Results The median age was 64; majority were white 85 (71%). Median TT was 209ng/dL (normal ≥200 ng/dL), FT was 4.4 ng/dL (normal ≥9 ng/dL), and BT was 22.0 ng/dL (normal ≥61ng/dL). Low TT, FT, and BT values were all associated with worse fatigue (p≤0.04), poor performance status (p≤0.05), weight loss (p≤0.01), and opioid use (p≤0.005). Low TT and FT were associated with increased anxiety (p≤0.04), decreased feeling of well-being (p≤0.04), and increased dyspnea (p≤0.05); while BT was only associated with anorexia (p=0.05). Decreased TT, FT, and BT values were all significantly associated with elevated CRP, low albumin and hemoglobin. In multivariate analysis, decreased survival was associated with low TT (HR 1.66; p=0.034), declining ECOG performance status (HR 1.55; p=0.004), high CRP (HR 3.28; p<0.001), and decreased albumin (HR 2.52; p<0.001). Conclusion In male cancer patients, low testosterone was associated with systemic inflammation, weight loss, increased symptom burden, and decreased survival. PMID:24577665

Characterization of the Marcellus Shale based on computer-assisted correlation of wireline logs in Virginia and West Virginia

USGS Publications Warehouse

Enomoto, Catherine B.; Olea, Ricardo A.; Coleman, James L.

2014-01-01

The Middle Devonian Marcellus Shale in the Appalachian basin extends from central Ohio on the west to eastern New York on the east, and from north-central New York on the north to northern Tennessee on the south. Its thickness ranges from 0 feet (ft) where it pinches out to the west to as much as 700 ft in its eastern extent. Within the Broadtop synclinorium, the thickness of the Marcellus Shale ranges from 250 to 565 ft. Although stratigraphic complexities have been documented, a significant range in thickness most likely is because of tectonic thickening from folds and thrust faults. Outcrop studies in the Valley and Ridge and Appalachian Plateaus provinces illustrate the challenges of interpreting the relation of third-order faults, folds, and “disturbed” zones to the regional tectonic framework. Recent field work within the Valley and Ridge province determined that significant faulting and intraformational deformation are present within the Marcellus Shale at the outcrop scale. In an attempt to determine if this scale of deformation is detectable with conventional wireline logs, petrophysical properties (primarily mineralogy and porosity) were measured by interpretation of gamma-ray and bulk-density logs. The results of performing a statistical correlation of wireline logs from nine wells indicated that there are discontinuities within the Millboro Shale (undifferentiated Marcellus Shale and Mahantango Formation) where there are significant thickness differences between wells. Also, some intervals likely contain mineralogy that makes these zones more prone to layer-shortening cleavage duplexes. The Correlator program proved to be a useful tool in a region of contractional deformation.

Hydrogeologic framework of sedimentary deposits in six structural basins, Yakima River basin, Washington

USGS Publications Warehouse

Jones, M.A.; Vaccaro, J.J.; Watkins, A.M.

2006-01-01

The hydrogeologic framework was delineated for the ground-water flow system of the sedimentary deposits in six structural basins in the Yakima River Basin, Washington. The six basins delineated, from north to south are: Roslyn, Kittitas, Selah, Yakima, Toppenish, and Benton. Extent and thicknesses of the hydrogeologic units and total basin sediment thickness were mapped for each basin. Interpretations were based on information from about 4,700 well records using geochemical, geophysical, geologist's or driller's logs, and from the surficial geology and previously constructed maps and well interpretations. The sedimentary deposits were thickest in the Kittitas Basin reaching a depth of greater than 2,000 ft, followed by successively thinner sedimentary deposits in the Selah basin with about 1,900 ft, Yakima Basin with about 1,800 ft, Toppenish Basin with about 1,200 ft, Benton basin with about 870 ft and Roslyn Basin with about 700 ft.

Gravity and magnetic data across the Ghost Dance Fault in WT-2 Wash, Yucca Mountain, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oliver, H.W.; Sikora, R.F.

1994-12-31

Detailed gravity and ground magnetic data were obtained in September 1993 along a 4,650 ft-long profile across the Ghost Dance Fault system in WT-2 Wash. Gravity stations were established every 150 feet along the profile. Total-field magnetic measurements made initially every 50 ft along the profile, then remade every 20 ft through the fault zone. These new data are part of a geologic and geophysical study of the Ghost Dance Fault (GDF) which includes detailed geologic mapping, seismic reflection, and some drilling including geologic and geophysical logging. The Ghost Dance Fault is the only through-going fault that has been identifiedmore » within the potential repository for high-level radioactive waste at Yucca Mountain, Nevada. Preliminary gravity results show a distinct decrease of 0.1 to 0.2 mGal over a 600-ft-wide zone to the east of and including the mapped fault. The gravity decrease probably marks a zone of brecciation. Another fault-offset located about 2,000 ft to the east of the GDF was detected by seismic reflection data and is also marked by a distinct gravity low. The ground magnetic data show a 200-ft-wide magnetic low of about 400 nT centered about 100 ft east of the Ghost Dance Fault. The magnetic low probably marks a zone of brecciation within the normally polarized Topopah Spring Tuff, the top of which is about 170 ft below the surface, and which is known from drilling to extend to a depth of about 1,700 ft. Three-component magnetometer logging in drill hole WT-2 located about 2,700 ft east of the Ghost Dance Fault shows that the Topopah Spring Tuff is strongly polarized magnetically in this area, so that fault brecciation of a vertical zone within the Tuff could provide an average negative magnetic contrast of the 4 Am{sup {minus}1} needed to produce the 400 nT low observed at the surface.« less

Borehole geophysical logging and aquifer-isolation tests conducted in well MG-1693 at North Penn Area 5 Superfund Site near Colmar, Montgomery County, Pennsylvania

USGS Publications Warehouse

Bird, Philip H.

2006-01-01

Borehole geophysical logging and aquifer-isolation (packer) tests were conducted in well MG-1693 (NP-87) at the North Penn Area 5 Superfund Site near Colmar, Montgomery County, Pa. Objectives of the study were to identify the depth and yield of water-bearing zones, occurrence of vertical borehole flow, and effects of pumping on water levels in nearby wells. Caliper, natural-gamma, single-point-resistance, fluidtemperature, fluid-resistivity, heatpulse-flowmeter, and borehole-video logs were collected. Vertical borehole-fluid movement direction and rate were measured under nonpumping conditions. The suite of logs was used to locate water-bearing fractures, determine zones of vertical borehole-fluid movement, and select depths to set packers. Aquifer-isolation tests were conducted to sample discrete intervals and to determine specific capacities of water-bearing zones and effects of pumping individual zones on water levels in two nearby monitor wells. Specific capacities of isolated zones during aquifer-isolation tests ranged from 0.03 to 3.09 (gal/min)/ft (gallons per minute per foot). Fractures identified by borehole geophysical methods as water-producing or water-receiving zones produced water when isolated and pumped.Water enters the borehole primarily through high-angle fractures at 416 to 435 ft bls (feet below land surface) and 129 to 136 ft bls. Water exits the borehole through a high-angle fracture at 104 to 107 ft bls, a broken casing joint at 82 ft bls, and sometimes as artesian flow through the top of the well. Thirteen intervals were selected for aquifer-isolation testing, using a straddle-packer assembly. The specific capacity of interval 1 was 2.09 (gal/min)/ft. The specific capacities of intervals 2, 3, and 4 were similar—0.27, 0.30, and 0.29 (gal/min)/ft, respectively. The specific capacities of intervals 5, 6, 7, 8, and 10 were similar—0.03, 0.04, 0.09, 0.09, and 0.04 (gal/min)/ft, respectively. Intervals 9, 11, and 12 each showed a strong hydraulic connection outside the borehole with intervals above and below the isolated interval. The specific capacities of intervals 9, 11, 12, and 13 were similar—2.12, 2.17, 3.09, and 3.08 (gal/min)/ft, respectively. The aquifer-isolation tests indicate that wells MG-1693 (NP-87) and MG-924 (NP-21) are connected primarily through the high-angle fracture from 416 to 435 ft bls. Pumping in either of these wells directly impacts the other well, allowing the pumped well to draw from water-bearing zones in the nonpumped well that are not present in or are not connected directly to the pumped well. The two boreholes act as a single, U-shaped well. The aquifer-isolation tests also show that the lower zones in well MG-1693 (NP-87) are a major source of hydraulic head in well MG-1661 (W-13) through the broken casing joint at 82 ft bls. Water moving upward from the lower intervals in well MG-1693 (NP-87) exits the borehole through the broken casing joint, moves upward outside the borehole, possibly around and (or) through a poor or damaged casing seal, and through the weathered zone above bedrock to well MG-1661 (W-13).Samples for volatile organic compounds (VOCs) were collected in nine isolated intervals. Six compounds were detected (1,1-dichloroethane, 1,1-dichloroethene, cis-1,2-dichloroethene, toluene, 1,1,1-trichloroethane, and trichloroethene (TCE)), and TCE was found in all nine isolated intervals. Intervals 4 (124-149 ft bls) and 6 (277-302 ft bls) had the highest total concentration of VOCs (6.66 and 6.2 micrograms per liter, respectively). Intervals 1 (68-93 ft bls) and 4 each had five compounds detected, which was the highest number of compounds detected. Interval 5 (252-277 ft bls) had the lowest total concentration of VOCs (0.08 microgram per liter) and the least number of VOCs detected (one). Detected compounds were not evenly distributed throughout the intervals. Contaminants were found in shallow, intermediate, and deep intervals and were associated with high-angle fractures and rough areas that showed no distinct fractures.

Logging costs and cutting methods in young-growth ponderosa pine in California

Treesearch

Philip M. McDonald; William A. Atkinson; Dale O. Hall

1969-01-01

Mixed-conifer stands at the Challenge Experimental Forest, Calif., were cut to four specifications: seed-tree, group selection, single tree selection, and clearcut. Logging costs and production rates were compared and evaluated. Cutting method had little effect on felling or skidding production; felling ranged from 1,802 to 2,019 bd ft per hour, and skidding from 3,138...

Neogene and Quaternary geology of a stratigraphic test hole on Horn Island, Mississippi Sound

USGS Publications Warehouse

Gohn, Gregory S.; Brewster-Wingard, G. Lynn; Cronin, Thomas M.; Edwards, Lucy E.; Gibson, Thomas G.; Rubin, Meyer; Willard, Debra A.

1996-01-01

During April and May, 1991, the U.S. Geological Survey (USGS) drilled a 510-ft-deep, continuously cored, stratigraphic test hole on Horn Island, Mississippi Sound, as part of a field study of the Neogene and Quaternary geology of the Mississippi coastal area. The USGS drilled two new holes at the Horn Island site. The first hole was continuously cored to a depth of 510 ft; coring stopped at this depth due to mechanical problems. To facilitate geophysical logging, an unsampled second hole was drilled to a depth of 519 ft at the same location.

Rational development of two flowthrough purification strategies for adenovirus type 5 and retro virus-like particles.

PubMed

Nestola, Piergiuseppe; Peixoto, Cristina; Villain, Louis; Alves, Paula M; Carrondo, Manuel J T; Mota, José P B

2015-12-24

We report on the rational design and implementation of flowthrough (FT) platforms for purification of virus vectors (VVs) and virus-like particles (VLPs), combining anion-exchange polyallylamine membranes (Sartobind STIC) and core-shell octylamine resins (CaptoCore 700). In one configuration, the VV bulk is concentrated and conditioned with appropriate buffer in a ultra/diafiltration (UF/DF) unit prior to injection into the STIC chromatography membrane. The FT pool and an intermediate cut of the elution pool of the STIC membrane are admixed and directed to a second UF/DF. Finally, the retentate is injected into a CC700 packed bed adsorber where the purified VVs are collected in the FT pool, whereas the residual amount of DNA and host cell protein (HCP) are discarded in the eluate. The experimental recovery achieved with this downstream processing (DSP) platform is close to 100%, the DNA clearance is roughly a 4-log reduction, and the HCP level is reduced by 5 logs. The platform developed for VLP purification is simpler than the previous one, as the STIC membrane adsorber and CC700 bed are connected in series with no UF/DF unit in between. Experimentally, the FT scheme for VLP purification gave a recovery yield of 45% in the chromatography train; the experimental log reduction of DNA and HCP were 2.0 and 3.5, respectively. These results are in line with other purification strategies in the specific field of enveloped VLPs. Both DSP platforms were successfully developed from an initial design space of the binding of the major contaminant (DNA) to the two ligands, determined by surface plasmon resonance, which was subsequently scaled up and confirmed experimentally. Copyright © 2015 Elsevier B.V. All rights reserved.

Fault reactivation and seismicity risk from CO2 sequestration in the Chinshui gas field, NW Taiwan

NASA Astrophysics Data System (ADS)

Sung, Chia-Yu; Hung, Jih-Hao

2015-04-01

The Chinshui gas field located in the fold-thrust belt of western Taiwan was a depleted reservoir. Recently, CO2 sequestration has been planned at shallower depths of this structure. CO2 injection into reservoir will generate high fluid pressure and trigger slip on reservoir-bounding faults. We present detailed in-situ stresses from deep wells in the Chinshui gas field and evaluated the risk of fault reactivation for underground CO2 injection. The magnitudes of vertical stress (Sv), formation pore pressure (Pf) and minimum horizontal stress (Shmin) were obtained from formation density logs, repeat formation tests, sonic logs, mud weight, and hydraulic fracturing including leak-off tests and hydraulic fracturing. The magnitude of maximum horizontal stress (SHmax) was constrained by frictional limit of critically stressed faults. Results show that vertical stress gradient is about 23.02 MPa/km (1.02 psi/ft), and minimum horizontal stress gradient is 18.05 MPa/km (0.80 psi/ft). Formation pore pressures were hydrostatic at depths 2 km, and increase with a gradient of 16.62 MPa/km (0.73 psi/ft). The ratio of fluid pressure and overburden pressure (λp) is 0.65. The upper bound of maximum horizontal stress constrained by strike-slip fault stress regime (SHmax>Sv>Shmin) and coefficient of friction (μ=0.6) is about 18.55 MPa/km (0.82 psi/ft). The orientation of maximum horizontal stresses was calculated from four-arm caliper tools through the methodology suggested by World Stress Map (WMS). The mean azimuth of preferred orientation of borehole breakouts are in ~65。N. Consequently, the maximum horizontal stress axis trends in 155。N and sub-parallel to the far-field plate-convergence direction. Geomechanical analyses of the reactivation of pre-existing faults was assessed using 3DStress and Traptester software. Under current in-situ stress, the middle block fault has higher slip tendency, but still less than frictional coefficient of 0.6 a common threshold value for motion on incohesive faults. The results also indicate that CO2 injection in the Chinshui gas field will not compromise the stability of faults.

The beta(+) decay and cosmic-ray half-life of Mn-54

NASA Astrophysics Data System (ADS)

Dacruz, M. T. F.; Norman, E. B.; Chan, Y. D.; Garcia, A.; Larimer, R. M.; Lesko, K. T.; Stokstad, R. G.; Wietfeldt, F. E.

1993-03-01

We performed a search for the beta(+) branch of Mn-54 decay. As a cosmic ray, Mn-54, deprived of its atomic electrons, can decay only via beta(+) and beta(-) decay, with a half-life of the order of 106 yr. This turns Mn-54 into a suitable cosmic chronometer for the study of cosmic-ray confinement times. We searched for coincident back-to-back 511-keV gamma-rays using two germanium detectors inside a Nal(Tl) annulus. An upper limit of 2 x 10-8 was found for the beta(+) decay branch, corresponding to a lower limit of 13.7 for the log ft value.

Calculated in situ rock density from gravity observations, UA-1 (Cannikin) emplacement hole, Amchitka Island, Alaska

USGS Publications Warehouse

Healey, D.L.

1971-01-01

Gravity observations were made on the ground surface and at a depth of 5,854 feet in drill hole UA-1. Two attempts to measure the free-air gradient utilizing the headframe over the drill hole were unsuccessful owing to mechanical vibrations in the structure. Because of the uncertainty in the measured free-air gradients these values were discarded and the average value (0.09406 mgal/ft) was used in the calculations. The calculated in situ bulk density is 2.36 g/cc. The weighted average bulk density determined from 47 core samples taken in the adjacent UAE-1 drill hole is also 2.36 g/cc. An analysis of selected portions of density logs provides an in situ bulk density of 2.37 g/cc.

Modeling of Combined Processing Steps for Reducing Escherichia coli O157:H7 Populations in Apple Cider

PubMed Central

Uljas, Heidi E.; Schaffner, Donald W.; Duffy, Siobain; Zhao, Lihui; Ingham, Steven C.

2001-01-01

Probabilistic models were used as a systematic approach to describe the response of Escherichia coli O157:H7 populations to combinations of commonly used preservation methods in unpasteurized apple cider. Using a complete factorial experimental design, the effect of pH (3.1 to 4.3), storage temperature and time (5 to 35°C for 0 to 6 h or 12 h), preservatives (0, 0.05, or 0.1% potassium sorbate or sodium benzoate), and freeze-thaw (F-T; −20°C, 48 h and 4°C, 4 h) treatment combinations (a total of 1,600 treatments) on the probability of achieving a 5-log10-unit reduction in a three-strain E. coli O157:H7 mixture in cider was determined. Using logistic regression techniques, pH, temperature, time, and concentration were modeled in separate segments of the data set, resulting in prediction equations for: (i) no preservatives, before F-T; (ii) no preservatives, after F-T; (iii) sorbate, before F-T; (iv) sorbate, after F-T; (v) benzoate, before F-T; and (vi) benzoate, after F-T. Statistical analysis revealed a highly significant (P < 0.0001) effect of all four variables, with cider pH being the most important, followed by temperature and time, and finally by preservative concentration. All models predicted 92 to 99% of the responses correctly. To ensure safety, use of the models is most appropriate at a 0.9 probability level, where the percentage of false positives, i.e., falsely predicting a 5-log10-unit reduction, is the lowest (0 to 4.4%). The present study demonstrates the applicability of logistic regression approaches to describing the effectiveness of multiple treatment combinations in pathogen control in cider making. The resulting models can serve as valuable tools in designing safe apple cider processes. PMID:11133437

Modeling of combined processing steps for reducing Escherichia coli O157:H7 populations in apple cider.

PubMed

Uljas, H E; Schaffner, D W; Duffy, S; Zhao, L; Ingham, S C

2001-01-01

Probabilistic models were used as a systematic approach to describe the response of Escherichia coli O157:H7 populations to combinations of commonly used preservation methods in unpasteurized apple cider. Using a complete factorial experimental design, the effect of pH (3. 1 to 4.3), storage temperature and time (5 to 35 degrees C for 0 to 6 h or 12 h), preservatives (0, 0.05, or 0.1% potassium sorbate or sodium benzoate), and freeze-thaw (F-T; -20 degrees C, 48 h and 4 degrees C, 4 h) treatment combinations (a total of 1,600 treatments) on the probability of achieving a 5-log(10)-unit reduction in a three-strain E. coli O157:H7 mixture in cider was determined. Using logistic regression techniques, pH, temperature, time, and concentration were modeled in separate segments of the data set, resulting in prediction equations for: (i) no preservatives, before F-T; (ii) no preservatives, after F-T; (iii) sorbate, before F-T; (iv) sorbate, after F-T; (v) benzoate, before F-T; and (vi) benzoate, after F-T. Statistical analysis revealed a highly significant (P < 0.0001) effect of all four variables, with cider pH being the most important, followed by temperature and time, and finally by preservative concentration. All models predicted 92 to 99% of the responses correctly. To ensure safety, use of the models is most appropriate at a 0.9 probability level, where the percentage of false positives, i.e., falsely predicting a 5-log(10)-unit reduction, is the lowest (0 to 4.4%). The present study demonstrates the applicability of logistic regression approaches to describing the effectiveness of multiple treatment combinations in pathogen control in cider making. The resulting models can serve as valuable tools in designing safe apple cider processes.

Gulf of Mexico Gas Hydrate Joint Industry Project Leg II: Results from the Walker Ridge 313 Site

NASA Astrophysics Data System (ADS)

Shedd, W.; Frye, M.; Boswell, R. M.; Collett, T. S.; McConnell, D.; Jones, E.; Shelander, D.; Dai, J.; Guerin, G.; Cook, A.; Mrozewski, S.; Godfriaux, P. D.; Dufrene, R.; Hutchinson, D. R.; Roy, R.

2009-12-01

The Gulf of Mexico Gas Hydrate Joint Industry Project Leg II drilling program visited three sites in the Gulf of Mexico during a 21 day drilling program in April and May, 2009. Using both petroleum systems and seismic stratigraphic approaches, the exploration focus for Leg II was to identify sites with the potential for gas hydrate-saturated sand reservoirs. The data acquired consist of a comprehensive suite of high resolution LWD logs including gamma ray, density, porosity, sonic, and resistivity tools. No physical samples were taken in the field. Two holes, locations G and H, were drilled at the Walker Ridge 313 site (WR 313)in the central Gulf of Mexico, just updip of the “salt sheet province”. The primary objective of each well was to determine the presence or absence of gas hydrate from the log data at the predetermined primary targets, picked from industry 3-D seismic data, in dipping Pleistocene turbidite derived sands on the flanks of a salt withdrawal minibasin. The seismic targets were high amplitude positive reflections just updip of phase reversals at the interpreted base of hydrate stability, corresponding to the so-called bottom simulating reflector, or “BSR”. Downdip of the BSR, the sands were clearly troughs, or negative reflections, suggesting free gas charge. An existing industry well, located updip of both JIP locations, contains a slightly sandy zone in the same stratigraphic interval as the JIP targets, that has elevated resistivities correlated to the target sands, suggesting low saturation “shows” of hydrate. Stratigraphically bounded fractured fine grained sediments with probable gas hydrate fill were found in both holes between 800 ft and 1300 ft at G, and between 600 ft and 1000 ft below the seafloor at H. At the primary targets, high saturation gas hydrates in sand were interpreted from logs at both holes. LWD data indicate 50 ft of high saturation gas hydrate in sands starting at 2722 ft below seafloor at the G hole. At H, 37 ft of high saturation gas hydrate was found in the target sand. Numerous minor occurrences of probable pore filling gas hydrate in thin sands were found at both locations. The likely discovery of thick gas hydrate-filled sands at the WR 313 site validates the exploration approach, and strongly indicates that gas hydrate can be found in reservoir quality marine sands. Additionally, the depth below mudline to which these wells were drilled without risers or drivepipe is unprecedented and the information gleaned will aid in marine hydrate exploration efforts worldwide.

Sandia SWiFT Wind Turbine Manual.

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Jonathan; LeBlanc, Bruce Philip; Berg, Jonathan Charles

The Scaled Wind Farm Technology (SWiFT) facility, operated by Sandia National Laboratories for the U.S. Department of Energy's Wind and Water Power Program, is a wind energy research site with multiple wind turbines scaled for the experimental study of wake dynamics, advanced rotor development, turbine control, and advanced sensing for production-scale wind farms. The SWiFT site currently includes three variable-speed, pitch-regulated, three-bladed wind turbines. The six volumes of this manual provide a detailed description of the SWiFT wind turbines, including their operation and user interfaces, electrical and mechanical systems, assembly and commissioning procedures, and safety systems. Further dissemination only asmore » authorized to U.S. Government agencies and their contractors; other requests shall be approved by the originating facility or higher DOE programmatic authority. 111 UNCLASSIFIED UNLIMITED RELEASE Sandia SWiFT Wind Turbine Manual (SAND2016-0746 ) approved by: Department Manager SWiFT Site Lead Dave Minster (6121) Date Jonathan White (6121) Date SWiFT Site Supervisor Dave Mitchell (6121) Date Note: Document revision logs are found after the title page of each volume of this manual. iv« less

Sawing to reduce warp in plantation red pine studs

Treesearch

Hiram Hallock; F.B. Malcolm

1972-01-01

Large volumes of red pine (Pinus resinosa) from plantations in the Lake States and the Northeastern States are about to appear on the saw log market. One of the most important products of small saw logs is studs (2 in. x 4 in. x 8 ft.). A study has been conducted by the FPL which examines the relationship of two industrial and one FPL sawing method on the subsequent...

Sawing to reduce warp in plantation red pine studs

Treesearch

Hiram Hallock; F.B. Malcolm

1972-01-01

Large volumes of red pine ( Pinus resinosa) from plantations in the Lake States and the Northeastern States are about to appear on the saw log market. One of the most important products of small saw logs is studs (2 in. x 4 in. x 8 ft.). A study has been conducted by the FPL which examines the relationship of two industrial and one FPL sawing method on the subsequent...

An integrated geophysical and hydraulic investigation to characterize a fractured-rock aquifer, Norwalk, Connecticut

USGS Publications Warehouse

Lane, J.W.; Williams, J.H.; Johnson, C.D.; Savino, D.M.; Haeni, F.P.

2002-01-01

The U.S. Geological Survey conducted an integrated geophysical and hydraulic investigation at the Norden Systems, Inc. site in Norwalk, Connecticut, where chlorinated solvents have contaminated a fractured-rock aquifer. Borehole, borehole-to-borehole, surface-geophysical, and hydraulic methods were used to characterize the site bedrock lithology and structure, fractures, and transmissive zone hydraulic properties. The geophysical and hydraulic methods included conventional logs, borehole imagery, borehole radar, flowmeter under ambient and stressed hydraulic conditions, and azimuthal square-array direct-current resistivity soundings. Integrated interpretation of geophysical logs at borehole and borehole-to-borehole scales indicates that the bedrock foliation strikes northwest and dips northeast, and strikes north-northeast to northeast and dips both southeast and northwest. Although steeply dipping fractures that cross-cut foliation are observed, most fractures are parallel or sub-parallel to foliation. Steeply dipping reflectors observed in the radar reflection data from three boreholes near the main building delineate a north-northeast trending feature interpreted as a fracture zone. Results of radar tomography conducted close to a suspected contaminant source area indicate that a zone of low electromagnetic (EM) velocity and high EM attenuation is present above 50 ft in depth - the region containing the highest density of fractures. Flowmeter logging was used to estimate hydraulic properties in the boreholes. Thirty-three transmissive fracture zones were identified in 11 of the boreholes. The vertical separation between transmissive zones typically is 10 to 20 ft. Open-hole and discrete-zone transmissivity was estimated from heat-pulse flowmeter data acquired under ambient and stressed conditions. The open-hole transmissivity ranges from 2 to 86 ft2/d. The estimated transmissivity of individual transmissive zones ranges from 0.4 to 68 ft2/d. Drawdown monitoring in nearby boreholes under pumping conditions identified hydraulic connections along a northeast-southwest trend between boreholes as far as 560 ft apart. The vertical distribution of fractures can be described by power law functions, which suggest that the fracture network contains transmissive zones consisting of closely spaced fractures surrounded by a less fractured and much less permeable rock mass.

Hydrocarbon potential, structural setting and depositional environments of Hammam Faraun Member of the Belayim Formation, Southern Gulf of Suez, Egypt

NASA Astrophysics Data System (ADS)

Nabawy, Bassem S.; El Sharawy, Mohamed S.

2015-12-01

The Middle Miocene Belayim Formation is one of the most prolific formations in the Southern Gulf of Suez. It consists of four members; two members are evaporitic (Baba and Feiran) and the other two members are prospective, mostly clastics (Hammam Faraun and Sidri). The hydrocarbon potential and depositional environment of Hammam Faraun Member, the target of the present study, have been studied in 11 wells distributed in the southern province of the Gulf of Suez. The traditional well log data, as well as the Spectral Gamma-Ray logs 'SGR' and dipmeter data were used to evaluate the petrophysical properties and distribution of the Hammam Faraun Member in the Southern Gulf of Suez. It varies greatly in thickness with the greatest thicknesses in GS 365 (372 ft) and GS 373 (430 ft) fields in the central parts and the thinnest at the basin margins of the studied area at GH376 (65 ft) and Ras El Bahar (67.5 ft) fields. It is composed of clastic rocks, mainly shales and sometimes reef carbonates. The very good petrophysical properties of the studied sequence indicate a good reservoir in some fields with good to very good porosity (13.5 ≤ ∅ ≤ 25.0%). The shale volume of this reservoir sequence is less than 33% and the water saturation is less than 42.3%, while the net-pay thickness is up to 58 ft. The SGR and Pe logs indicate that, the studied rocks were deposited mostly in lagoonal to shallow marine environments, with illite and montmorillonite as dominant clay minerals. The dipmeter data obtained in some wells indicate slightly tilted beds, mostly less than 20° with an overall dip direction towards the SW, which represents the regional dip in the Southern Gulf of Suez. Based on dipmeter data, two major angular unconformities can be detected; one at the top of the sequence, separating it from the overlying South Gharib evaporates, and another one at the base of the sequence, separating it from the underlying Feiran Member.

Geologic logs of geotechnical cores from the subsurface Sacramento-San Joaquin Delta, California

USGS Publications Warehouse

Maier, Katherine L.; Ponti, Daniel J.; Tinsley, John C.; Gatti, Emma; Pagenkopp, Mark

2014-01-01

This report presents and summarizes descriptive geologic logs of geotechnical cores collected from 2009–12 in the Sacramento–San Joaquin Delta, California, by the California Department of Water Resources. Graphic logs are presented for 1,785.7 ft of retained cores from 56 borehole sites throughout the Sacramento-San Joaquin Delta. Most core sections are from a depth of ~100–200 feet. Cores primarily contain mud, silt, and sand lithologies. Tephra (volcanic ash and pumice), paleosols, and gravels are also documented in some core sections. Geologic observations contained in the core logs in this report provide stratigraphic context for subsequent sampling and data for future chronostratigraphic subsurface correlations.

Identification and evaluation of the probiotic potential of Lactobacillus paraplantarum FT259, a bacteriocinogenic strain isolated from Brazilian semi-hard artisanal cheese.

PubMed

Tulini, Fabrício Luiz; Winkelströter, Lizziane Kretli; De Martinis, Elaine C P

2013-08-01

This study aimed to identify a bacteriocinogenic Lactobacillus isolate (FT259) obtained from Brazilian semi-hard Minas type cheese and to evaluate its probiotic and antimicrobial potentials. The strain was identified by biochemical tests (at genus level), and by 16S rDNA sequencing combined with recA gene amplification (for species). To determine the inhibitory spectrum towards food borne pathogens and lactic acid bacteria, the spot-on-the-lawn assay was carried out. Moreover, the proteinaceous nature of the antimicrobial compound produced was evaluated by susceptibility to degradation by proteolytic enzymes. The isolated strain was tested for survival in acidified culture media (pH 2.0, 2.5 and 3.5), in vitro tolerance to bile salts and viability under gastric conditions. Adhesion of Lactobacillus paraplantarum FT259 to Caco-2 cells was evaluated by surface plate count on De Man, Rogosa, and Sharpe (MRS) agar and also by FISH method (fluorescent in situ hybridization) with the aid of Eub338 probe for fluorescence microscopy analysis. The isolate was identified as L. paraplantarum FT259 and it produced bacteriocins that inhibited the growth of Listeria monocytogenes, Listeria innocua and several lactic acid bacteria. It was also observed that L. paraplantarum FT259 tolerated exposure to pH 3.5, and bile salts 0.3% for up to 180 min. In experiments with simulated gastric juice, viable cells of L. paraplantarum FT259 decreased from 8.6 log CFU/mL to 3.5 log CFU/mL after 180 min. For the same strain, in studies with Caco-2 cells, 74% of adhesion was observed through plate count and FISH assays. It was also demonstrated isolated FT259 was susceptible to the majority the antibiotics tested. Overall, the results indicated L. paraplantarum FT259 is a potential probiotic and the production of bacteriocin may be an interesting feature for food applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

In-situ gas hydrate hydrate saturation estimated from various well logs at the Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope

USGS Publications Warehouse

Lee, M.W.; Collett, T.S.

2011-01-01

In 2006, the U.S. Geological Survey (USGS) completed detailed analysis and interpretation of available 2-D and 3-D seismic data and proposed a viable method for identifying sub-permafrost gas hydrate prospects within the gas hydrate stability zone in the Milne Point area of northern Alaska. To validate the predictions of the USGS and to acquire critical reservoir data needed to develop a long-term production testing program, a well was drilled at the Mount Elbert prospect in February, 2007. Numerous well log data and cores were acquired to estimate in-situ gas hydrate saturations and reservoir properties.Gas hydrate saturations were estimated from various well logs such as nuclear magnetic resonance (NMR), P- and S-wave velocity, and electrical resistivity logs along with pore-water salinity. Gas hydrate saturations from the NMR log agree well with those estimated from P- and S-wave velocity data. Because of the low salinity of the connate water and the low formation temperature, the resistivity of connate water is comparable to that of shale. Therefore, the effect of clay should be accounted for to accurately estimate gas hydrate saturations from the resistivity data. Two highly gas hydrate-saturated intervals are identified - an upper ???43 ft zone with an average gas hydrate saturation of 54% and a lower ???53 ft zone with an average gas hydrate saturation of 50%; both zones reach a maximum of about 75% saturation. ?? 2009.

Characterization of cementitiously stabilized subgrades for mechanistic-empirical pavement design

NASA Astrophysics Data System (ADS)

Solanki, Pranshoo

Pavements are vulnerable to subgrade layer performance because it acts as a foundation. Due to increase in the truck traffic, pavement engineers are challenged to build more strong and long-lasting pavements. To increase the load-bearing capacity of pavements, subgrade layer is often stabilized with cementitious additives. Thus, an overall characterization of stabilized subgrade layer is important for enhanced short- and long-term pavement performance. In this study, the effect of type and amount of additive on the short-term performance in terms of material properties recommended by the new Mechanistic-Empirical Pavement Design Guide (MEPDG) is examined. A total of four soils commonly encountered as subgrades in Oklahoma are utilized. Results show that the changes in the Mr, ME and UCS values stabilized specimens depend on the soil type and properties of additives. The long-term performance (or durability) of stabilized soil specimens is investigated by conducting freeze-thaw (F-T) cycling, vacuum saturation and tube suction tests on 7-day cured P-, K- and C-soil specimens stabilized with 6% lime, 10% CFA and 10% CKD. This study is motivated by the fact that during the service life of pavement stabilized layers are subjected to F-T cycles and moisture variations. It is found that that UCS value of all the stabilized specimens decreased with increase in the number of F-T cycles. A strong correlation was observed between UCS values retained after vacuum saturation and F-T cycles indicating that vacuum saturation could be used as a time-efficient and inexpensive method for evaluating durability of stabilized soils. In this study, short- and long-term observations from stabilization of sulfate bearing soil with locally available low (CFA), moderate (CKD) and high (lime) calcium-based stabilizers are determined to evaluate and compare the effect of additive type on the phenomenon of sulfate-induced heave. The impact of different factors on the development of the ettringite, responsible for sulfate-induced heaving, is also discussed. For Level 2 design of pavements, a total of four stress-based statistical models and two feed-forward-type artificial neural network (ANN) models, are evaluated for predicting resilient modulus of 28-day cured stabilized specimens. Specifically, one semi-log stress-based, three log-log stress-based, one Multi-Layer Perceptrons Network (MLPN), and one Radial Basis Function Network (RBFN) are developed. Overall, semi-log stress-based and MLPN neural network are found to show best acceptable performance for the present evaluation and validation datasets. Further, correlations are presented for stress-based models to correlate Mr with compacted specimen characteristics and soil/additive properties. Additionally, the effect of type of additive on indirect tensile and fatigue characteristics of selected stabilized P- and V-soil is evaluated. This study is based on the fact that stabilized layer is subjected to tensile stresses under wheel loading. Thus, the resilient modulus in tension (M rt), fatigue life and strength in tension (sigmat) or flexure (represented by modulus of rupture, MOR) becomes another important design parameter within the mechanistic framework. Cylindrical specimens are prepared, cured for 28 days and subjected to different stress sequences in indirect tension to study the Mrt. On the other hand, stabilized beam specimens are compacted using a Linear Kneading Compactor and subjected to repeated cycles of reloading-unloading after 28 days of curing in a four-point beam fatigue apparatus for evaluating fatigue life and flexural stiffness. It is found that all three additives improved the Mrt, sigmat and MOR values; however, degree of improvement varied with the type of additive and soil. This study encompasses the differences in the design of semi-rigid pavements developed using AASHTO 1993 and AASHTO 2002 MEPDG methodologies. Further, the design curves for fatigue performance prediction of stabilized layers are developed for different stabilized pavement sections. Knowledge gained from the parametric analysis of different sections using AASHTO 1993 and MEPDG is expected to be useful to pavement designers and others in implementation of the new MEPDG for future pavement design. (Abstract shortened by UMI.)

Using open hole and cased-hole resistivity logs to monitor gas hydrate dissociation during a thermal test in the mallik 5L-38 research well, Mackenzie Delta, Canada

USGS Publications Warehouse

Anderson, B.I.; Collett, T.S.; Lewis, R.E.; Dubourg, I.

2008-01-01

Gas hydrates, which are naturally occurring ice-like combinations of gas and water, have the potential to provide vast amounts of natural gas from the world's oceans and polar regions. However, producing gas economically from hydrates entails major technical challenges. Proposed recovery methods such as dissociating or melting gas hydrates by heating or depressurization are currently being tested. One such test was conducted in northern Canada by the partners in the Mallik 2002 Gas Hydrate Production Research Well Program. This paper describes how resistivity logs were used to determine the size of the annular region of gas hydrate dissociation that occurred around the wellbore during the thermal test in the Mallik 5L-38 well. An open-hole logging suite, run prior to the thermal test, included array induction, array laterolog, nuclear magnetic resonance and 1.1-GHz electromagnetic propagation logs. The reservoir saturation tool was run both before and after the thermal test to monitor formation changes. A cased-hole formation resistivity log was run after the test.Baseline resistivity values in each formation layer (Rt) were established from the deep laterolog data. The resistivity in the region of gas hydrate dissociation near the wellbore (Rxo) was determined from electromagnetic propagation and reservoir saturation tool measurements. The radius of hydrate dissociation as a function of depth was then determined by means of iterative forward modeling of cased-hole formation resistivity tool response. The solution was obtained by varying the modeled dissociation radius until the modeled log overlaid the field log. Pretest gas hydrate production computer simulations had predicted that dissociation would take place at a uniform radius over the 13-ft test interval. However, the post-test resistivity modeling showed that this was not the case. The resistivity-derived dissociation radius was greatest near the outlet of the pipe that circulated hot water in the wellbore, where the highest temperatures were recorded. The radius was smallest near the center of the test interval, where a conglomerate section with low values of porosity and permeability inhibited dissociation. The free gas volume calculated from the resistivity-derived dissociation radii yielded a value within 20 per cent of surface gauge measurements. These results show that the inversion of resistivity measurements holds promise for use in future gas hydrate monitoring. ?? 2008 Society of Petrophysicists and Well Log Analysts. All rights reserved.

Log bioassay of residual effectiveness of insecticides against bark beetles

Treesearch

Richard H. Smith

1982-01-01

Residual effectiveness of nine insecticides applied to bark was tested against western, mountain, and Jeffrey pine beetles. Ponderosa and Jeffrey pine trees were treated and logs cut from them 2 to 13 months later, and bioassayed with the three beetles. The insecticides were sprayed at the rate of 1 gal (3.8 l) per 40- or 80-ft² (3.6 or 7.2 m²) bark surface at varying...

Engineering report on drilling in the San Rafael Swell area, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, L.I.

1980-05-01

The San Rafael Swell drilling project was conducted by Bendix Field Engineering Corporation in support of the US Department of Energy National Uranium Resource Evaluation (NURE) program. This project consisted of 27 drill holes ranging in depth from 120.0 ft (36.5 m) to 3,700.0 ft (1,127.7 m). A total of 41,716 ft (12,715 m) was drilled, of which 3,099.8 ft (944.8 m) were cored. Geophysical logging was supplied by Century Geophysical Corporation and Bendix Field Engineering Corporation. The objective of the project was to test the uranium potential of the Triassic and Jurassic sandstone units and to investigate areas wheremore » industry was unlikely to drill in the near future. Drilling commenced September 24, 1978, and was finished on December 17, 1979.« less

Geologic and engineering properties investigations: Project Sulky

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lutton, R.J.; Girucky, F.E.

1966-09-01

The Sulky event was a nuclear cratering experiment in which a device yielding 85 + 15 tons was detonated at a depth of 90 ft in jointed basalt. The explosion produced a rubble-covered mound roughly circular in plan and extending approximately 24 ft above the original ground surface. Prior to the event the Sulky site was explored by means of 6 core borings and the emplacement calyx hole. Geophysical logging was conducted and laboratory tests were performed on representative samples. Postshot investigations consisted of trenching through the mound and drilling 3 core borings to determine the extent of the rupturemore » zone. The rock consists of vesicular basalt over dense basalt and each type is structurally modified by layering of vesicles resulting from viscous flow of the lava. Unconfined compressive strengths range from about 10,000 psi for vesicular basalt to about 20,000 psi for dense basalt. Bulk specific gravities for dense basalt are about 2.74, but with increasing vesicle content the bulk specific gravity reaches values as low as 2.40.« less

Summary of public water-supply withdrawals and geohydrologic data for the lower Connecticut River valley from Windsor to Vernon, Vermont

USGS Publications Warehouse

Ayotte, Joseph

1989-01-01

Public water supply withdrawal data and geohydrologic data were collected along a 50 mile segment of the Connecticut River valley from Windsor to Vernon, Vermont. An inventory of wells indicates that domestic groundwater supplies come primarily from bedrock, whereas public water supplies are derived from discontinuous, glacial sand and gravel deposits. Self supplied industries generally use surface water supplies. Data from eight seismic-refraction surveys, and from a seismic-reflection survey along this 50-mile reach of the Connecticut River, were compared with stratigraphic information from 217 drillers ' logs. Stratified-drift deposits range from 0 to 270 ft and average about 65 ft. Stratigraphic information from drillers ' logs and seismic-reflection records show that predominantly fine-grained stratified drift fills the valley and that coarse sand and gravel deposits exist discontinuously within this area. (USGS)

What's new in well logging and formation evaluation

USGS Publications Warehouse

Prensky, S.

2011-01-01

A number of significant new developments is emerging in well logging and formation evaluation. Some of the new developments include an ultrasonic wireline imager, an electromagnetic free-point indicator, wired and fiber-optic coiled tubing systems, and extreme-temperature logging-while-drilling (LWD) tools. The continued consolidation of logging and petrophysical service providers in 2010 means that these innovations are increasingly being provided by a few large companies. Weatherford International has launched a slimhole cross-dipole tool as part of the company's line of compact logging tools. The 26-ft-long Compact Cross-Dipole Sonic (CXD) tool can be run as part of a quad-combo compact logging string. Halliburton has introduced a version of its circumferential acoustic scanning tool (CAST) that runs on monoconductor cable (CAST-M) to provide high-resolution images in open hole and in cased hole for casing and cement evaluation.

Characterization of Vadose Zone Sediment: Borehole 299-E33-46 Near Tank B-110 in the B-BX-BY Waste Management Area.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serne, R. Jeffrey; Bjornstad, Bruce N.; Gee, Glendon W.

2002-12-15

This report presents vadose sediment characterization data that improves understanding of the nature and extent of past releases in the B tank farm. A vertical borehole, located approximately 15 ft (5 m) from the northeast edge of single-shell tank 241-B-110 was drilled to a total depth of 264.4 ft bgs, the groundwater table was encountered at 255.8 ft bgs. During drilling, a total of 3 two-ft long, 4-inch diameter split-spoon core samples were collected between 10 and 254 ft bgs-an average of every 7.5 ft. Grab samples were collected between these core sample intervals to yield near continuous samples tomore » a depth of 78.3 m (257 ft). Geologic logging occurred after each core segment was emptied into an open plastic container, followed by photographing and sub-sampling for physical and chemical characterization. In addition, 54 out of a total of 120 composite grab samples were opened, sub-sampled, logged, and photographed. Immediately following the geologic examination, the core and selected grab samples were sub-sampled for moisture content, gamma-emission radiocounting, tritium and strontium-90 determinations, total carbon and inorganic carbon content, and 8 M nitric acid extracts (which provide a measure of the total leachable sediment content of contaminants) and one-to-one sediment to water extracts (which provide soil pH, electrical conductivity, cation, and anion data and water soluble contaminant data. Later, additional aliquots of selected sleeves or grab samples were removed to measure particle size distribution and mineralogy and to squeeze porewater. Major conclusions follow. Vadose zone contamination levels were lower than generally anticipated prior to the initiation of the field investigation. Strong evidence of extensive vadose zone lateral migration in WMA BBXBY exists. There are indications that such lateral migration may have extended into WMA B-BX-BY from adjacent past practice discharge sites. Ponding of runoff from natural precipitation in the WMA may have added significant amounts of spatially confined infiltration. Borehole soil characterization has identified strontium-90 and technetium-99 as the two main radionuclides underneath tank B-110. The Sr-90 data indicate limited future mobility unless abnormally high amounts of infiltration occur. Neither technetium-99 nor strontium-90 is expected to significantly impact groundwater in the current moisture and geochemical environment below the B Tank Farm. At borehole 299-E33-46 (near tank B-110), strontium 90 was found down to 26 m (85 ft) bgs with strontium 90 values up to 11,250 pCi/g of sediment. Other tank wastes contaminants (e.g., nitrate) were found down to 69 m (200 ft) bgs. The strontium-90 was immobile under the current ionic regime in the pore water. Technetium-99 releases into the vadose zone near tank B-110 from a transfer line leak appear to be inconsequential. Technetium-99 does not occur above detection limits in the upper parts of the vadose zone where other tank waste constituents (e.g., strontium-90, fluoride, carbonate, and nitrate) are present. Technetium-99 is present in a few soil samples in the PlioPleistocene unit. This unit appears to be an effective conduit for lateral migration and the presence of technetium-99 is postulated to have another source.« less

SCD-HeFT: Use of RR Interval Statistics for Long-term Risk Stratification for Arrhythmic Sudden Cardiac Death

PubMed Central

Au-yeung, Wan-tai M.; Reinhall, Per; Poole, Jeanne E.; Anderson, Jill; Johnson, George; Fletcher, Ross D.; Moore, Hans J.; Mark, Daniel B.; Lee, Kerry L.; Bardy, Gust H.

2015-01-01

Background In the SCD-HeFT a significant fraction of the congestive heart failure (CHF) patients ultimately did not die suddenly from arrhythmic causes. CHF patients will benefit from better tools to identify if ICD therapy is needed. Objective To identify predictor variables from baseline SCD-HeFT patients’ RR intervals that correlate to arrhythmic sudden cardiac death (SCD) and mortality and to design an ICD therapy screening test. Methods Ten predictor variables were extracted from pre-randomization Holter data from 475 patients enrolled in the SCD-HeFT ICD arm using novel and traditional heart rate variability methods. All variables were correlated to SCD using Mann Whitney-Wilcoxon test and receiver operating characteristic analysis. ICD therapy screening tests were designed by minimizing the cost of false classifications. Survival analysis, including log-rank test and Cox models, was also performed. Results α1 and α2 from detrended fluctuation analysis, the ratio of low to high frequency power, the number of PVCs per hour and heart rate turbulence slope are all statistically significant for predicting the occurrences of SCD (p<0.001) and survival (log-rank p<0.01). The most powerful multivariate predictor tool using the Cox Proportional Hazards was α2 with a hazard ratio of 0.0465 (95% CI: 0.00528 – 0.409, p<0.01). Conclusion Predictor variables from RR intervals correlate to the occurrences of SCD and distinguish survival among SCD-HeFT ICD patients. We believe SCD prediction models should incorporate Holter based RR interval analysis to refine ICD patient selection especially in removing patients who are unlikely to benefit from ICD therapy. PMID:26096609

Mass Airflow Cabinet for Control of Airborne Infection of Laboratory Rodents

PubMed Central

McGarrity, Gerard J.; Coriell, Lewis L.

1973-01-01

A mass airflow cabinet for handling and housing of laboratory rodents has been developed and tested. The unit consists of a high-efficiency particulate air filter and uniform distribution of air at a vertical velocity of 19 cm per s. Animals are maintained without bedding in mesh-bottomed cages that rest on rollers for rotation inside the cabinet. There is an air barrier of 90 cm per s separating the cabinet air from room air. Sampling for airborne bacteria yielded an average of 0.03 colony-forming units (CFU) per ft3 of air inside the cabinet, whereas 28.8 CFU per ft3 was simultaneously detected outside the cabinet during housekeeping, a reduction of almost three logs. The efficiency of the air barrier was tested by aerosolization of T3 phage. When phage was aerosolized 5 cm outside the cabinet, no phage could be detected 5 cm inside when the fans were operating; with the fans off an average of 1.6 × 104 plaque-forming units (PFU) per ft3 was detected in six tests. Aerosolization of phage inside the cabinet yielded an average of 9 × 10 PFU per ft3 outside; an average of 4.1 × 106 PFU per ft3 were detected with the fans not in operation, a reduction of more than four logs. In-use studies on effectiveness showed that the cabinet significantly reduced the incidence of mice originally titer-free to Reo-3 virus. Hemagglutination inhibition antibodies to Reo-3 were detected in 9/22 (42%) mice housed in a conventionally ventilated animal laboratory while no seroconversion was detected in any of 22 mice housed in the mass air flow cabinet in the same laboratory. Images PMID:4355261

Mass airflow cabinet for control of airborne infection of laboratory rodents.

PubMed

McGarrity, G J; Coriell, L L

1973-08-01

A mass airflow cabinet for handling and housing of laboratory rodents has been developed and tested. The unit consists of a high-efficiency particulate air filter and uniform distribution of air at a vertical velocity of 19 cm per s. Animals are maintained without bedding in mesh-bottomed cages that rest on rollers for rotation inside the cabinet. There is an air barrier of 90 cm per s separating the cabinet air from room air. Sampling for airborne bacteria yielded an average of 0.03 colony-forming units (CFU) per ft(3) of air inside the cabinet, whereas 28.8 CFU per ft(3) was simultaneously detected outside the cabinet during housekeeping, a reduction of almost three logs. The efficiency of the air barrier was tested by aerosolization of T3 phage. When phage was aerosolized 5 cm outside the cabinet, no phage could be detected 5 cm inside when the fans were operating; with the fans off an average of 1.6 x 10(4) plaque-forming units (PFU) per ft(3) was detected in six tests. Aerosolization of phage inside the cabinet yielded an average of 9 x 10 PFU per ft(3) outside; an average of 4.1 x 10(6) PFU per ft(3) were detected with the fans not in operation, a reduction of more than four logs. In-use studies on effectiveness showed that the cabinet significantly reduced the incidence of mice originally titer-free to Reo-3 virus. Hemagglutination inhibition antibodies to Reo-3 were detected in 9/22 (42%) mice housed in a conventionally ventilated animal laboratory while no seroconversion was detected in any of 22 mice housed in the mass air flow cabinet in the same laboratory.

Solar cycle variation of geosynchronous plasma mass density derived from the frequency of standing Alfvén waves

NASA Astrophysics Data System (ADS)

Takahashi, Kazue; Denton, Richard E.; Singer, Howard J.

2010-07-01

We have studied the solar cycle variation of equatorial plasma mass density ρeq in the plasma trough at geosynchronous altitude. The density was indirectly determined from the frequency, fT3, of the third harmonic of toroidal standing Alfvén waves detected over a 12 year period from 1980 to 1991 with magnetometers on five Geostationary Operational Environmental Satellites (GOES). Realistic models of the ambient magnetic field and field line mass distribution were used in numerically solving the wave equation to relate fT3 to ρeq. Scanning the magnetometer data in a 30 min time window that moved forward in 10 min steps, we obtained 228,382 fT3 samples equivalent to 1586 days of data. The detection rate of fT3 is highest (˜50%) in the prenoon sector, and fT3 and ρeq samples from this sector were used to examine their dependence on F10.7, Kp, and Dst. Overall, F10.7 exhibits the highest correlation with fT3 and ρeq, implying that the solar UV/EUV control of ion production at the ionospheric height is strongly reflected in mass density variations at geosynchronous orbit. Using 27 day medians computed excluding periods of plasmasphere expansion to geosynchronous orbit and geomagnetic storm, we obtained the empirical formula fT3 (mHz) = 38 - 0.097F10.7 and logρeq (amu cm-3) = 0.42 + 0.0039F10.7, where F10.7 is given in the solar flux units 10-22 W · m-2 · Hz-1. This last formula means that with the 27 day F10.7 in the range of 68-255 in the selected solar cycle, the mass density varied by a factor of ˜5 from ˜5 to ˜26 amu cm-3. During extremely quiet times (Kp averaged using a 3 day time scale <1), for which the plasmasphere may extend out to geosynchronous orbit, and during storm periods (Dst < -50 nT), the mass density may be enhanced beyond these values.

Depth of the base of the Jackson aquifer, based on geophysical exploration, southern Jackson Hole, Wyoming, USA

USGS Publications Warehouse

Nolan, B.T.; Campbell, D.L.; Senterfit, R.M.

1998-01-01

A geophysical survey was conducted to determine the depth of the base of the water-table aquifer in the southern part of Jackson Hole, Wyoming, USA. Audio-magnetotellurics (AMT) measurements at 77 sites in the study area yielded electrical-resistivity logs of the subsurface, and these were used to infer lithologic changes with depth. A 100-600 ohm-m geoelectric layer, designated the Jackson aquifer, was used to represent surficial saturated, unconsolidated deposits of Quaternary age. The median depth of the base of the Jackson aquifer is estimated to be 200 ft (61 m), based on 62 sites that had sufficient resistivity data. AMT-measured values were kriged to predict the depth to the base of the aquifer throughout the southern part of Jackson Hole. Contour maps of the kriging predictions indicate that the depth of the base of the Jackson aquifer is shallow in the central part of the study area near the East and West Gros Ventre Buttes, deeper in the west near the Teton fault system, and shallow at the southern edge of Jackson Hole. Predicted, contoured depths range from 100 ft (30 m) in the south, near the confluences of Spring Creek and Flat Creek with the Snake River, to 700 ft (210 m) in the west, near the town of Wilson, Wyoming.

Decontamination of Bacillus spores adhered to iron and cement-mortar drinking water infrastructure in a model system using disinfectants.

PubMed

Szabo, Jeffrey G; Meiners, Greg; Heckman, Lee; Rice, Eugene W; Hall, John

2017-02-01

Decontamination of Bacillus spores adhered to common drinking water infrastructure surfaces was evaluated using a variety of disinfectants. Corroded iron and cement-mortar lined iron represented the infrastructure surfaces, and were conditioned in a 23 m long, 15 cm diameter (75 ft long, 6 in diameter) pilot-scale drinking water distribution pipe system. Decontamination was evaluated using increased water velocity (flushing) alone at 0.5 m s -1 (1.7 ft s -1 ), as well as free chlorine (5 and 25 mg L -1 ), monochloramine (25 mg L -1 ), chlorine dioxide (5 and 25 mg L -1 ), ozone (2.0 mg L -1 ), peracetic acid 25 mg L -1 ) and acidified nitrite (0.1 mol L -1 at pH 2 and 3), all followed by flushing at 0.3 m s -1 (1 ft s -1 ). Flushing alone reduced the adhered spores by 0.5 and 2.0 log 10 from iron and cement-mortar, respectively. Log 10 reduction on corroded iron pipe wall coupons ranged from 1.0 to 2.9 at respective chlorine dioxide concentrations of 5 and 25 mg L -1 , although spores were undetectable on the iron surface during disinfection at 25 mg L -1 . Acidified nitrite (pH 2, 0.1 mol L -1 ) yielded no detectable spores on the iron surface during the flushing phase after disinfection. Chlorine dioxide was the best performing disinfectant with >3.0 log 10 removal from cement-mortar at 5 and 25 mg L -1 . The data show that free chlorine, monochloramine, ozone and chlorine dioxide followed by flushing can reduce adhered spores by > 3.0 log 10 on cement-mortar. Published by Elsevier Ltd.

Interpretation of borehole geophysical logs, aquifer-isolation tests, and water quality, supply wells 1 and 2, Willow Grove Naval Air Station/Joint Reserve Base, Horsham Township, Montgomery County, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.; Goode, Daniel J.; Frasch, Steven M.

2002-01-01

Ground water pumped from supply wells 1 and 2 on the Willow Grove Naval Air Station/Joint Reserve Base (NAS/JRB) provides water for use at the base, including potable water for drinking. The supply wells have been contaminated by volatile organic compounds (VOC's), particularly trichloroethylene (TCE) and tetrachloroethylene (PCE), and the water is treated to remove the VOC's. The Willow Grove NAS/JRB and surrounding area are underlain by sedimentary rocks of the Triassic-age Stockton Formation, which form a complex, heterogeneous aquifer.The ground-water-flow system for the supply wells was characterized by use of borehole geophysical logs and heatpulse-flowmeter measurements. The heatpulse-flowmeter measurements showed upward and downward borehole flow under nonpumping conditions in both wells. The hydraulic and chemical properties of discrete water-bearing fractures in the supply wells were characterized by isolating each water-bearing fracture with straddle packers. Eight fractures in supply well 1 and five fractures in supply well 2 were selected for testing on the basis of the borehole geophysical logs and borehole television surveys. Water samples were collected from each isolated fracture and analyzed for VOC?s and inorganic constituents.Fractures at 50–59, 79–80, 196, 124–152, 182, 241, 256, and 350–354 ft btoc (feet below top of casing) were isolated in supply well 1. Specific capacities ranged from 0.26 to 5.7 (gal/min)/ft (gallons per minute per foot) of drawdown. The highest specific capacity was for the fracture isolated at 179.8–188 ft btoc. Specific capacity and depth of fracture were not related in either supply well. The highest concentrations of PCE were in water samples collected from fractures isolated at 236.8–245 and 249.8–258 ft btoc, which are hydraulically connected. The concentration of PCE generally increased with depth to a maximum of 39 mg/L (micrograms per liter) at a depth of 249.8? 258 ft btoc and then decreased to 21 mg/L at a depth of 345.3–389 ft btoc.Fractures at 68–74, 115, 162, 182, 205, and 314 ft btoc were isolated in supply well 2. Specific capacities ranged from 0.08 to less than 2.9 (gal/ min)/ft. The highest specific capacity was for the fracture isolated at 157–165.2 ft btoc. Concentrations of detected VOC's in water samples were 3.6 mg/L or less.Lithologic units penetrated by both supply wells were determined by correlating naturalgamma and single-point-resistance borehole geophysical logs. All lithologic units are not continuous water-bearing units because water-bearing fractures are not necessarily present in the same lithologic units in each well. Although the wells penetrate the same lithologic units, the lithologic location of only three water-bearing fractures are common to both wells. The same lithologic unit may have different hydraulic properties in each well.A regional ground-water divide is southeast of the supply wells. From this divide, ground water flows northwest toward Park Creek, a tributary to Little Neshaminy Creek. Potentiometric-surface maps were prepared from water levels measured in shallow and deep wells. For both depth intervals, the direction of ground-water flow is toward the northwest. For most well clusters, the vertical head gradient is downward from the shallow to the deeper part of the aquifer. Pumping of the supply wells at times can cause the vertical flow direction to reverse.

Preliminary geological interpretation and lithologic log of the exploratory geothermal test well (INEL-1), Idaho National Engineering Laboratory, eastern Snake River Plain, Idaho

USGS Publications Warehouse

Doherty, David J.; McBroome, Lisa Ann; Kuntz, Mel A.

1979-01-01

A 10,365 ft (3,159 m) geothermal test well was drilled in the spring of 1979 at the Idaho National Engineering Laboratory, eastern Snake River Plain, Idaho: The majority of rock types encountered in the borehole are of volcanic origin. An upper section above 2,445 ft (745 m) consists of basaltic lava flows and interbedded .sediments of alluvial, lacustrine, and volcanic origin. A lower section below 2,445 ft (745 m) consists exclusively of rhyolitic welded ash-flow tuffs, air-fall ash deposits, nonwelded ash-flow ruffs, and volcaniclastic sediments. The lithology and thickness of the rhyolitic rocks suggest that they are part of an intracaldera fill.

Evaluation of geophysical logs and aquifer-isolation tests, Phase III, August 2002 to March 2004, Crossley Farm superfund site, Hereford township, Berks County, Pennsylvania

USGS Publications Warehouse

Conger, Randall W.; Low, Dennis J.

2006-01-01

Between August 2002 and March 2004, geophysical logging was conducted in 23 boreholes at the Crossley Farm Superfund Site, Hereford Township, Berks County, Pa., to determine the water-producing zones, water-receiving zones, zones of vertical-borehole flow, and fracture orientation where applicable. The boreholes ranged in depth from 71 to 503 ft (feet) below land surface. The geophysical logging determined the placement of well screens and packers, which allow monitoring and sampling of water-bearing zones in the fractured bedrock so the horizontal and vertical distribution of contaminated ground water migrating from known sources could be determined. Geophysical logging included collection of caliper (22 boreholes), fluid-temperature (17 boreholes), single-pointresistance (17 boreholes), natural-gamma (17 boreholes), fluidflow (18 boreholes), and acoustic-televiewer (13 boreholes) logs. Caliper and acoustic-televiewer logs were used to locate fractures, joints, and weathered zones. Inflections on fluid-temperature and single-point-resistance logs indicated possible water-bearing zones, and flowmeter measurements verified these locations. Single-point-resistance, natural-gamma, and geologist logs provided information on stratigraphy; the geologist log also provided information on the location of possible water-producing zones.Borehole geophysical logging and heatpulse flowmetering indicated active flow in 10 boreholes. Seven of the boreholes are in ground-water discharge areas and three boreholes are in ground-water recharge areas. Heatpulse flowmetering, in conjunction with the geologist logs, indicates lithologic contacts (changes in lithology from a gneiss dominated by quartz-plagioclase-feldspar mineralogy to a gneiss dominated by hornblende mineralogy) are typically fractured, permeable, and effective transmitters of water. Single-well, aquifer-isolation (packer) tests were performed on two boreholes. Packers were set at depths ranging from 210 to 465 ft below land surface to isolate water-bearing zones at discrete intervals. Placement and inflation of the packers provided information on hydraulic heads, specific capacities, the hydraulic connection between intervals, and depth-specific water-quality samples. Upon completion of borehole geophysical logging and interpretation of geophysical logs, geologist logs, drillers notes, and packer work, 13 boreholes were reconstructed such that water levels could be monitored and water samples could be collected from discrete shallow, intermediate, and deep waterbearing fractures in each borehole. Boreholes BE-1672, BE-1674, BE-1676, and BE-1677 remained open-hole for sampling purposes. Boreholes RI-2, RI-3, and RI-4 remained openhole for injection purposes. Boreholes P-1, P-2, and P-3 remained open and were converted to pumping wells.

Urinary metabolomics reveals glycemic and coffee associated signatures of thyroid function in two population-based cohorts

PubMed Central

Friedrich, Nele; Pietzner, Maik; Cannet, Claire; Thuesen, Betina H.; Hansen, Torben; Wallaschofski, Henri; Grarup, Niels; Skaaby, Tea; Budde, Kathrin; Pedersen, Oluf; Nauck, Matthias; Linneberg, Allan

2017-01-01

Background Triiodothyronine (T3) and thyroxine (T4) as the main secretion products of the thyroid affect nearly every human tissue and are involved in a broad range of processes ranging from energy expenditure and lipid metabolism to glucose homeostasis. Metabolomics studies outside the focus of clinical manifest thyroid diseases are rare. The aim of the present investigation was to analyze the cross-sectional and longitudinal associations of urinary metabolites with serum free T4 (FT4) and thyroid-stimulating hormone (TSH). Methods Urine Metabolites of participants of the population-based studies Inter99 (n = 5620) and Health2006/Health2008 (n = 3788) were analyzed by 1H-NMR spectroscopy. Linear or mixed linear models were used to detect associations between urine metabolites and thyroid function. Results Cross-sectional analyses revealed positive relations of alanine, trigonelline and lactic acid with FT4 and negative relations of dimethylamine, glucose, glycine and lactic acid with log(TSH). In longitudinal analyses, lower levels of alanine, dimethylamine, glycine, lactic acid and N,N-dimethylglycine were linked to a higher decline in FT4 levels over time, whereas higher trigonelline levels were related to a higher FT4 decline. Moreover, the risk of hypothyroidism was higher in subjects with high baseline trigonelline or low lactic acid, alanine or glycine values. Conclusion The detected associations mainly emphasize the important role of thyroid hormones in glucose homeostasis. In addition, the predictive character of these metabolites might argue for a potential feedback of the metabolic state on thyroid function. Besides known metabolic consequences of TH, the link to the urine excretion of trigonelline, a marker of coffee consumption, represents a novel finding of this study and given the ubiquitous consumption of coffee requires further research. PMID:28253303

Low triiodothyronine: A new facet of inflammation in acute ischemic stroke.

PubMed

Ma, Lili; Zhu, Dongliang; Jiang, Ying; Liu, Yingying; Ma, Xiaomeng; Liu, Mei; Chen, Xiaohong

2016-07-01

Patients with acute ischemic stroke (AIS) frequently experience low free triiodothyronine (fT3) concentrations. Inflammation is recognized as a key contributor to the pathophysiology of stroke. Previous studies, however, did not simultaneously evaluate fT3 and inflammation biomarkers in AIS patients. Markers of inflammation, including serum concentrations of C-reactive protein (CRP) and albumin, and fT3 were assessed retrospectively in 117 patients. Stroke severity was measured on the National Institutes of Health Stroke Scale (NIHSS). Regression analyses were performed to adjust for confounders. Serum fT3 concentrations were significantly lower in moderate AIS patients than those in mild AIS patients (P<0.001). fT3 concentration also positively correlated with serum albumin concentration (r=0.358, P<0.001) and negatively correlated with log10CRP concentration (r=-0.341, P<0.001), NIHSS score (r=-0.384, P<0.001). Multiple regression analysis showed that CRP, albumin concentrations and NIHSS score were independently correlated with fT3 concentration. Binary logistic regression analysis showed that fT3 concentration was an independent factor correlated with NIHSS score, the area under the receiver operating characteristic curve was 0.712 (95% CI, 0.618-0.805). Low fT3 concentrations may be involved in the pathogenic pathway linking inflammation to stroke severity in AIS patients. Copyright © 2016 Elsevier B.V. All rights reserved.

Total and free iodothyronine changes in response to transport of Equidae (Equus asinus and Equus caballus).

PubMed

Fazio, Esterina; Medica, Pietro; Cravana, Cristina; Ferlazzo, Adriana

2017-03-31

In this study the effects of short distance road transport on total and free iodothyronine changes in 12 stallions (Equus asinus and Equus caballus) were evaluated. Donkeys (n = 6) and horses (n = 6) were transported for a distance of 50 km. Blood samples were collected 1 week before transport in basal conditions, 1 week later immediately before loading, and after transport and unloading. After transport, donkeys showed significant increases in circulating T4 (P≤0.01), fT3 (P≤0.001), and fT4 (P≤0.01) levels; while horses had significant increases in circulating T3, fT3 and fT4 (P≤0.01) levels. Compared to donkeys' values, horses showed lower T4 values in basal condition, before and after transport (P≤0.001); higher fT3 values in basal condition and before (P≤0.001), and lower values (P≤0.001) after transport; higher fT4 values (P≤0.001) in basal condition. The results indicate that short road transport of donkeys and horses induces the activation of the thyroid gland, with the same release of fT3 and fT4 iodothyronines, but with different preferential release of T3 in horses and T4 in donkeys after transport.

Static noise tests on augmentor wing jet STOL research aircraft (C8A Buffalo)

NASA Technical Reports Server (NTRS)

Marrs, C. C.; Harkonen, D. L.; Okeefe, J. V.

1974-01-01

Results are presented for full scale ground static acoustic tests of over-area conical nozzles and a lobe nozzle installed on the Augmentor Wing Jet STOL Research Aircraft, a modified C8A Buffalo. The noise levels and spectrums of the test nozzles are compared against those of the standard conical nozzle now in use on the aircraft. Acoustic evaluations at 152 m (500 ft), 304 m (1000 ft), and 1216 m (4000 ft) are made at various engine power settings with the emphasis on approach and takeoff power. Appendix A contains the test log and propulsion calculations. Appendix B gives the original test plan, which was closely adhered to during the test. Appendix C describes the acoustic data recording and reduction systems, with calibration details.

β decay of proton-rich nucleus Al23 and astrophysical consequences

NASA Astrophysics Data System (ADS)

Iacob, V. E.; Zhai, Y.; Al-Abdullah, T.; Fu, C.; Hardy, J. C.; Nica, N.; Park, H. I.; Tabacaru, G.; Trache, L.; Tribble, R. E.

2006-10-01

We present the first study of the β decay of Al23 undertaken with pure samples. The study was motivated by nuclear astrophysics questions. Pure samples of Al23 were obtained from the momentum achromat recoil separator (MARS) of Texas A&M University, collected on a fast tape-transport system, and moved to a shielded location where β and β-γ coincidence measurements were made. We deduced β branching ratios and log ft values for transitions to states in Mg23, and from them determined unambiguously the spin and parity of the Al23 ground state to be Jπ=5/2+. We discuss how this excludes the large increases in the radiative proton capture cross section for the reaction Mg22(p,γ)Al23 at astrophysical energies, which were implied by claims that the spin and parity is Jπ=1/2+. The log ft for the Fermi transition to its isobaric analog state (IAS) in Mg23 is also determined for the first time. This IAS and a state 16 keV below it are observed, well separated in the same experiment for the first time. We can now solve a number of inconsistencies in the literature, exclude strong isospin mixing claimed before, and obtain a new determination of the resonance strength. Both states are resonances in the Na22(p,γ)Mg23 reaction at energies important in novae. The reactions Mg22(p,γ)Al23 and Na22(p,γ)Mg23 have both been suggested as possible candidates for diverting some of the flux in oxygen-neon novae explosions from the A=22 into the A=23 mass chain.

Reservoir evaluation of thin-bedded turbidites and hydrocarbon pore thickness estimation for an accurate quantification of resource

NASA Astrophysics Data System (ADS)

Omoniyi, Bayonle; Stow, Dorrik

2016-04-01

One of the major challenges in the assessment of and production from turbidite reservoirs is to take full account of thin and medium-bedded turbidites (<10cm and <30cm respectively). Although such thinner, low-pay sands may comprise a significant proportion of the reservoir succession, they can go unnoticed by conventional analysis and so negatively impact on reserve estimation, particularly in fields producing from prolific thick-bedded turbidite reservoirs. Field development plans often take little note of such thin beds, which are therefore bypassed by mainstream production. In fact, the trapped and bypassed fluids can be vital where maximising field value and optimising production are key business drivers. We have studied in detail, a succession of thin-bedded turbidites associated with thicker-bedded reservoir facies in the North Brae Field, UKCS, using a combination of conventional logs and cores to assess the significance of thin-bedded turbidites in computing hydrocarbon pore thickness (HPT). This quantity, being an indirect measure of thickness, is critical for an accurate estimation of original-oil-in-place (OOIP). By using a combination of conventional and unconventional logging analysis techniques, we obtain three different results for the reservoir intervals studied. These results include estimated net sand thickness, average sand thickness, and their distribution trend within a 3D structural grid. The net sand thickness varies from 205 to 380 ft, and HPT ranges from 21.53 to 39.90 ft. We observe that an integrated approach (neutron-density cross plots conditioned to cores) to HPT quantification reduces the associated uncertainties significantly, resulting in estimation of 96% of actual HPT. Further work will focus on assessing the 3D dynamic connectivity of the low-pay sands with the surrounding thick-bedded turbidite facies.

Completion Report for Well ER-4-1 Corrective Action Unit 97: Yucca Flat/Climax Mine, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wurtz, Jeffrey; Rehfeldt, Ken

Well ER-4-1 was drilled for the U.S. Department of Energy, Nevada National Security Administration Nevada Field Office in support of the Underground Test Area (UGTA) Activity. The well was drilled and completed from March 23 to April 13, 2016, as part of the Corrective Action Investigation Plan (CAIP) for Yucca Flat/Climax Mine Corrective Action Unit (CAU) 97. The primary purpose of the well was to collect hydrogeologic data to assist in validating concepts of the groundwater flow system within the Yucca Flat/Climax Mine CAU, and to test for potential radionuclides in groundwater from the STRAIT (U4a) underground test. The completedmore » well includes one piezometer (p1), to a depth of 663.16 meters (m) (2,175.71 feet [ft]) below ground surface (bgs) and open from the Alluvial aquifer (AA3) to the Oak Spring Butte confining unit (OSBCU) hydrostratigraphic units; and a main completion (m1), which includes 6.625-inch (in.) casing with slotted interval (m1) installed to 906.80 m (2,975.05 ft) bgs in the Lower carbonate aquifer (LCA). A 13.375-in. diameter surface casing was installed from the surface to a depth of 809.00 m (2,654.21 ft) bgs. Well ER-4-1 experienced a number of technical issues during drilling, including borehole instability and sloughing conditions. An intermediate, 10.75-in./9.625-in. casing string was installed to 856.94 m (2,811.48 ft) bgs to control these issues. Borehole stability and erosion problems appear to be associated with the Tunnel Formation (Tn) and the Older tunnel beds (Ton). Overall efforts to stabilize the borehole were successful. Data collected during borehole construction include composite drill cutting samples collected every 3.0 m (10 ft), a partial suite of geophysical logs to a maximum depth of 766.57 m (2,515 ft) bgs, water-quality measurements (including tritium), water-level measurements, and two depth-discrete bailer samples collected at 538.89 m and 646.18 m (1,768 ft and 2,120 ft) bgs respectively. The well penetrated 187.45 m (615 ft) of Quaternary/Tertiary alluvium (QTa), 671.47 m (2,203 ft) of Tertiary Volcanic rocks (Tv), and 66.20 m (217.19 ft) of Paleozoic rocks (|). The stratigraphy and lithology were generally as expected with some exceptions. The top of Paleozoic rocks (|) was predicted to occur at 822.35 m (2,698 ft) bgs and was intercepted at 858.93 m (2,818 ft), a difference of 36.58 m (120 ft). As expected, the Paleozoic rocks (|) are the principal water producing formation in Well ER-4-1. Depth to water was measured after drilling as follows: In the piezometers: p1 at 320.39 m (1,051.16 ft) bgs, (measured January 4, 2017); and in the main production casing interval: m1 at 539.17 m (1,768.92 ft) bgs, (measured December 12, 2016) Geophysical logs and depth-discrete bailer sample analytical results suggest likely zones of prompt injection (underground-test-related) fission products from 472.44 to 481.48 m (1,550 to 1,580 ft) bgs and at approximately 539.50 m (1,770 ft) bgs. Subsequent work at Well ER-4-1 will be included in future reports. Field measurements for tritium were mostly below the Safe Drinking Water Act limit (20,000 picocuries per liter) with the exception of two zones showing elevated tritium concentrations. The first zone is located at approximately 365.76 to 390.14 m (1,200 to 1,280 ft) bgs and a second zone at approximately 542.54 to 566.93 m (1,780 to 1,860 ft) bgs. All Fluid Management Plan requirements were met.« less

Gulf of Mexico Gas Hydrate Joint Industry Project Leg II: Results from the Alaminos Canyon 21 Site

NASA Astrophysics Data System (ADS)

Godfriaux, P. D.; Shedd, W.; Frye, M.; Collett, T. S.; Lee, M. W.; Boswell, R. M.; Cook, A.; Mrozewski, S.; Guerin, G.; McConnell, D.; Dufrene, R.; Jones, E.

2009-12-01

The Gulf of Mexico Gas Hydrate Joint Industry Project Leg II drilling program visited three sites in the Gulf of Mexico during a 21 day drilling program in April and May, 2009. Using both petroleum systems and seismic stratigraphic approaches, the exploration focus for Leg II was to identify sites with the potential for gas hydrate-saturated sand reservoirs. Two holes were drilled at the AC 21 site in the Diana Basin located in the western Gulf of Mexico. The data acquired consist of a comprehensive suite of high resolution LWD logs including gamma ray, density, porosity, sonic, and resistivity tools. No physical samples were taken in the field. The primary objective of each well was to determine the presence or absence of gas hydrate from the log data at the predetermined primary targets in a Pleistocene basin floor turbidite complex approximately 500 ft below seafloor. At the AC 21-A location, two high net to gross target sands were encountered that measured 15 ft and 60 ft, respectively. The AC 21-A well was drilled through the interpreted base of gas hydrate stability to a depth approximately 1500 ft below sea floor. The AC 21-B well encountered a single high net to gross target sand measuring over 120 ft thick. At both AC 21 well locations, all target sand intervals had elevated formation resistivity measurements relative to clearly wet, stratigraphically equivalent sands encountered in the region, interpreted to indicate low to moderate levels of gas hydrate saturation. The likely discovery of thick gas hydrate-filled sands at the AC 21 site validates the exploration approach, and strongly indicates that gas hydrate can be found in reservoir quality sands. The LWD acquired data provided unprecedented information on the nature of the sediments and the occurrence of gas hydrate in the Gulf of Mexico.

Comparison of topical dorzolamide and ketorolac treatment for cystoid macular edema in retinitis pigmentosa and Usher's syndrome.

PubMed

Lemos Reis, Ricardo Filipe; Moreira-Gonçalves, Nuno; Estrela Silva, Sérgio E; Brandão, Elisete M; Falcão-Reis, Fernando M

2015-01-01

To investigate the topical effect of dorzolamide versus ketorolac on retinitis pigmentosa (RP) and Usher's syndrome (US) macular edema. Prospective, randomized and interventional study. A total of 28 eyes of 18 patients were included. Five eyes had US, 23 had RP. Fifteen eyes were allocated to ketorolac tromethamine 0.5% (4 drops daily regimen) and 13 eyes to dorzolamide hydrochloride 2% (3 drops daily regimen) treatment groups. Snellen's best-corrected visual acuity (BCVA), foveal thickness (FT) and foveal zone thickness (FZT) measured by Stratus® optical coherence tomography (OCT) were evaluated at baseline, 1, 3, 6 and 12 months after treatment. Patients assigned to ketorolac had a baseline BCVA of 0.37 ± 0.17 logMAR which improved at the end of 1 year to 0.28 ± 0.16 (p = 0.02). Three eyes (20%) of 2 patients improved by 7 letters or more. Mean FT and FZT did not change significantly during the study follow-up. After 1 year of treatment, 4 eyes (27%) of 3 patients showed an improvement of at least 16% of FT and 11% of FZT. Patients assigned to dorzolamide had a baseline BCVA of 0.48 ± 0.34 logMAR which improved in the first 6 months (0.40 ± 0.30; p = 0.01), with a decrease at 1 year (0.42 ± 0.27; p = 0.20). Seven eyes (54%) of 5 patients had an improvement of 7 letters or more. Mean FT and FZT did not change significantly either. After 1 year of treatment, 3 eyes (23%) of 2 patients showed an improvement of at least 16% on FT and 11% on FZT. RESULTS suggest that dorzolamide and ketorolac might improve visual acuity and therefore be of interest in selected cases. No relationship between retinal thickness fluctuation and visual acuity was found. Sample size was a limitation to the study. © 2014 S. Karger AG, Basel.

River-aquifer exchanges in the Yakima River basin, Washington

USGS Publications Warehouse

Vaccaro, J.J.

2011-01-01

Five categories of data are analyzed to enhance understanding of river-aquifer exchanges-the processes by which water moves between stream channels and the adjacent groundwater system-in the Yakima River basin. The five datasets include (1) results of chemical analyses of water for tritium (3H, a radioactive isotope of hydrogen) and the ratios of the stable isotopes of hydrogen (2H/1H) and oxygen (18O/16O), (2) series of stream discharge measurements within specified reaches (seepage investigations or 'runs'), (3) vertical hydraulic gradients (between stream stage and hydraulic heads the underlying aquifer) measured using mini-piezometers, (4) groundwater levels and water temperature in shallow wells near stream channels, and (5) thermal profiles (continuous records of water temperature along river reaches). Exchanges are described in terms of streamflow, vertical hydraulic gradients, groundwater temperature and levels, and streamflow temperature, and where appropriate, the exchanges are discussed in terms of their relevance to and influence on salmonid habitat. The isotope data shows that the ultimate source of surface and groundwater is meteoric water derived from atmospheric precipitation. Water from deep wells has a different isotopic composition than either shallow groundwater or surface water, indicating that the deep groundwater system contributes, at most, only a small component of the surface-water discharge. The isotope data confirms that river-aquifer exchanges involve primarily modern streamflow and modern, shallow groundwater. Net exchanges of water for 46 stream sections investigated with seepage runs ranged from nearly zero to 1,071 ft3/s for 28 gaining sections, and -3 to -242 ft3/s for 18 losing sections. The magnitude of the upper 50 percent of the net gains is an order of magnitude larger than those for net losses. The sections have a normalized net exchange (as absolute value) that fully ranged from near 0 to 65.6 (ft3/s)/mi. Gaining-section values ranged from about 0.1 to 65.6 (ft3/s)/mi, and losing section values ranged from about -0.1 to -35.4 (ft3/s)/mi. Gains are much more vigorous than the losses with 55 percent being larger than 3.0 (ft3/s)/ mi, whereas, only 6 percent of the negative net exchanges were larger than 3.0 (ft3/s)/mi. Gains and losses for 167 measured reaches within the 46 sections ranged from about 70 to -75 (ft3/s)/mi, and ranged more than 5 orders of magnitude. The median values for the gains and losses were 5.1 and -4.4 (ft3/s)/mi, respectively. The magnitude of the gains was larger than the losses; more than 40 percent of the gains were greater than 10 (ft3/s)/mi, and only about 25 percent of the losses were greater than 10 (ft3/s)/mi. Reaches with large gains are identified and these reaches represent potentially important areas for various life stages of salmonids and possibly for preservation or restoration of that habitat. Ninety-nine measurements of vertical hydraulic gradients (VHGs) were made using mini-piezometers. The median for the measurements was -0.35 ft/ft (negative values indicate downward flow), and in terms of absolute values, the median was 0.05 ft/ft. The VHGs tended to be small. Seventy VHG values were negative (indicating streamflow losses), and 29 were positive (indicating streamflow gains). VHGs vary more than 4 orders of magnitude, and in terms of magnitudes, 65 percent were less than 0.1 ft/ft. The negative VHG values are not only more prevalent but are larger than the positive values. The magnitudes of almost 50 percent of the negative VHGs are greater than 0.05 ft/ft and only 33 percent of the positive VHGs are greater than 0.05 ft/ft. The percentile distribution of the VHG data, which is similar to the shape of the seepage data distribution, shows that beyond the 80th percentile, the positive values become much larger, indicating that the largest VHGs have a different controlling mechanism. The VHGs were formulated in terms of fluxes per unit are

Mount Elbert Gas Hydrate Stratigraphic Test Well, Alaska North Slope: Coring operations, core sedimentology, and lithostratigraphy

USGS Publications Warehouse

Rose, K.; Boswell, R.; Collett, T.

2011-01-01

In February 2007, BP Exploration (Alaska), the U.S. Department of Energy, and the U.S. Geological Survey completed the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well (Mount Elbert well) in the Milne Point Unit on the Alaska North Slope. The program achieved its primary goals of validating the pre-drill estimates of gas hydrate occurrence and thickness based on 3-D seismic interpretations and wireline log correlations and collecting a comprehensive suite of logging, coring, and pressure testing data. The upper section of the Mount Elbert well was drilled through the base of ice-bearing permafrost to a casing point of 594??m (1950??ft), approximately 15??m (50??ft) above the top of the targeted reservoir interval. The lower portion of the well was continuously cored from 606??m (1987??ft) to 760??m (2494??ft) and drilled to a total depth of 914??m. Ice-bearing permafrost extends to a depth of roughly 536??m and the base of gas hydrate stability is interpreted to extend to a depth of 870??m. Coring through the targeted gas hydrate bearing reservoirs was completed using a wireline-retrievable system. The coring program achieved 85% recovery of 7.6??cm (3??in) diameter core through 154??m (504??ft) of the hole. An onsite team processed the cores, collecting and preserving approximately 250 sub-samples for analyses of pore water geochemistry, microbiology, gas chemistry, petrophysical analysis, and thermal and physical properties. Eleven samples were immediately transferred to either methane-charged pressure vessels or liquid nitrogen for future study of the preserved gas hydrate. Additional offsite sampling, analyses, and detailed description of the cores were also conducted. Based on this work, one lithostratigraphic unit with eight subunits was identified across the cored interval. Subunits II and Va comprise the majority of the reservoir facies and are dominantly very fine to fine, moderately sorted, quartz, feldspar, and lithic fragment-bearing to -rich sands. Lithostratigraphic and palynologic data indicate that this section is most likely early Eocene to late Paleocene in age. The examined units contain evidence for both marine and non-marine lithofacies, and indications that the depositional environment for the reservoir facies may have been shallower marine than originally interpreted based on pre-drill wireline log interpretations. There is also evidence of reduced salinity marine conditions during deposition that may be related to the paleo-climate and depositional conditions during the early Eocene. ?? 2010.

VizieR Online Data Catalog: New multiplet table for FeI (Nave+, 1994)

NASA Astrophysics Data System (ADS)

Nave, G.; Johansson, S.; Learner, R. C. M.; Thorne, A. P.; Brault, J. W.

1995-02-01

We have recorded spectra of iron-neon and iron-argon hollow cathode lamps in the region 1700A-5um (59,000-2000cm-1), with Fourier transform (FT) spectrometers at the National Solar Observatory, Tucson, Arizona, and Imperial College, London, UK, and with a high-resolution grating spectrograph at the National Institute of Standards and Technology, Gaithersburg, Maryland. The uncertainty of the strongest lines in the FT spectra is less than 0.002cm-1 (0.2mA at 3000A; 8mA at 2um). Pressure- and current-dependent shifts are less than 0.001cm-1 for transitions between low-lying levels, increasing to 0.006cm-1 for transitions between the most highly excited levels. We report 28 new energy levels of Fe I and revised values of another 818 levels. We have identified 9501 lines as due to 9759 transitions in Fe I, and these are presented in the form of a new multiplet table and finding list. This compares with the ~5500 lines due to 467 energy levels in the multiplet tables of Moore (1950, NBS Circ., No.488 and 1959, NBS Tech. note 30). The biggest increase is in the near-ultraviolet and near infrared, and many of the new lines are present in the solar spectrum. Experimental log (gf) values are included where they are available. A further 125 unidentified lines due to Fe I are given. (4 data files).

Integrated interpretation of C-8 and G-61 sandstones at Badak and Nilam fields in Sanga-Sanga block of east Kalimantan, Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ade, W.C.; Suwarlan, W.

1989-03-01

Huffco's Badak and Nilam fields are giant gas fields that together currently produce more than 1.0 bcf of gas per day from sandstones within the Miocene Balikpapan beds. The reservoir sandstones were deposited within a thick regressive deltaic sequence that includes coals, shales, and occasional limestones. Wells typically encounter multiple stacked pay sandstones at depths ranging from about 5500 ft to more than 13,000 ft. Individual sandstone thicknesses can vary from several feet to more than 20 ft. Abrupt lateral stratigraphic variations in sandstone thickness are the rule rather than the exception. Sandstone reservoir interpretations are based on an integratedmore » approach by incorporating the study of well logs, cores, seismic sections, normal moveout-corrected gathers, amplitude variations with offset (AVO) graphs, and pressure and reservoir performance data.« less

In-line monitoring of a pharmaceutical blending process using FT-Raman spectroscopy.

PubMed

Vergote, G J; De Beer, T R M; Vervaet, C; Remon, J P; Baeyens, W R G; Diericx, N; Verpoort, F

2004-03-01

FT-Raman spectroscopy (in combination with a fibre optic probe) was evaluated as an in-line tool to monitor a blending process of diltiazem hydrochloride pellets and paraffinic wax beads. The mean square of differences (MSD) between two consecutive spectra was used to identify the time required to obtain a homogeneous mixture. A traditional end-sampling thief probe was used to collect samples, followed by HPLC analysis to verify the Raman data. Large variations were seen in the FT-Raman spectra logged during the initial minutes of the blending process using a binary mixture (ratio: 50/50, w/w) of diltiazem pellets and paraffinic wax beads (particle size: 800-1200 microm). The MSD-profiles showed that a homogeneous mixture was obtained after about 15 min blending. HPLC analysis confirmed these observations. The Raman data showed that the mixing kinetics depended on the particle size of the material and on the mixing speed. The results of this study proved that FT-Raman spectroscopy can be successfully implemented as an in-line monitoring tool for blending processes.

Biostratigraphic data for the Cretaceous marine sediments in the USGS-St. George no. 1 core (DOR-211), Dorchester County, South Carolina

USGS Publications Warehouse

Self-Trail, Jean M.; Gohn, Gregory S.

1997-01-01

The USGS-St. George corehole was drilled for the U.S. Geological Survey (USGS) by a commercial drilling company during 1982. The corehole is located within the Coastal Plain Province in northern Dorchester County, South Carolina, about three miles southeast of the town of St. George near the village of Byrd (fig. 1). Coordinates for the corehole are 33o09'25'N latitude and 80o31'18'W longitude; ground elevation at the site is +78 feet (Reid and others, 1986). The St. George corehole is designated as USGS drill hole DOR-211. The St. George corehole was drilled to a total depth of 2,067 ft. The hole was cored continuously with generally good recovery from 300 ft to its total depth. Spot cores were taken at selected intervals between the top of the hole and a depth of 300 ft (50-55 ft, 100-110 ft, 150-165 ft, 200-205 ft, and 250-255 ft); however, recovery was poor in most of these intervals. The St. George core currently is stored at the USGS National Center, Reston, VA (March, 1997). The St. George corehole bottomed in basalt of probable early Mesozoic age beneath an Upper Cretaceous and Cenozoic sedi-mentary section. Reid and others (1986) placed the top of basalt saprolite at 1,962 ft in the hole. Our examination of the geophysical logs and original core descriptions suggests that the top of the saprolite is higher in the hole, at about 1,939 ft. The Cretaceous-Tertiary boundary was placed at or near 550 ft in the core by Reid and others (1986) and by Habib and Miller (1989). In this report, we provide paleontologic data for marine sediments in the upper part of the Upper Cretaceous section in the St. George core. Biostratigraphic and paleoenvironmental data and interpretations based on the study of calcareous nannofossils and ostracodes from the Cretaceous section are discussed.

Association between hypogonadism, symptom burden, and survival in male patients with advanced cancer.

PubMed

Dev, Rony; Hui, David; Del Fabbro, Egidio; Delgado-Guay, Marvin O; Sobti, Nikhil; Dalal, Shalini; Bruera, Eduardo

2014-05-15

A high frequency of hypogonadism has been reported in male patients with advanced cancer. The current study was performed to evaluate the association between low testosterone levels, symptom burden, and survival in male patients with cancer. Of 131 consecutive male patients with cancer, 119 (91%) had an endocrine evaluation of total (TT), free (FT), and bioavailable testosterone (BT); high-sensitivity C-reactive protein (CRP); vitamin B12; thyroid-stimulating hormone; 25-hydroxy vitamin D; and cortisol levels when presenting with symptoms of fatigue and/or anorexia-cachexia. Symptoms were evaluated by the Edmonton Symptom Assessment Scale. The authors examined the correlation using the Spearman test and survival with the log-rank test and Cox regression analysis. The median age of the patients was 64 years; the majority of patients were white (85 patients; 71%). The median TT level was 209 ng/dL (normal: ≥ 200 ng/dL), the median FT was 4.4 ng/dL (normal: ≥ 9 ng/dL), and the median BT was 22.0 ng/dL (normal: ≥ 61 ng/dL). Low TT, FT, and BT values were all associated with worse fatigue (P ≤ .04), poor Eastern Cooperative Oncology Group performance status (P ≤ .05), weight loss (P ≤ .01), and opioid use (P ≤ .005). Low TT and FT were associated with increased anxiety (P ≤ .04), a decreased feeling of well-being (P ≤ .04), and increased dyspnea (P ≤ .05), whereas low BT was only found to be associated with anorexia (P = .05). Decreased TT, FT, and BT values were all found to be significantly associated with elevated CRP and low albumin and hemoglobin. On multivariate analysis, decreased survival was associated with low TT (hazards ratio [HR], 1.66; P = .034), declining Eastern Cooperative Oncology Group performance status (HR, 1.55; P = .004), high CRP (HR, 3.28; P < .001), and decreased albumin (HR, 2.52; P < .001). In male patients with cancer, low testosterone levels were associated with systemic inflammation, weight loss, increased symptom burden, and decreased survival. A high frequency of hypogonadism has been reported in male patients with advanced cancer. In the current study, an increased symptom burden, systemic inflammation, weight loss, opioid use, and poor survival were found to be associated with decreased testosterone levels in male patients with cancer. Cancer 2014;120:1586-1593. © 2014 American Cancer Society. © 2014 American Cancer Society.

A pilot study: subclinical hypothyroidism and free thyroid hormone measurement by immunoassay and mass spectrometry.

PubMed

Gounden, Verena; Jonklaas, Jacqueline; Soldin, Steven J

2014-03-20

The diagnosis of subclinical hypothyroidism is defined as the presence of an elevated thyroid stimulating hormone (TSH) with a normal free thyroxine (FT4) level. The commonly used direct analogue immunoassays for the measurement of FT4 have been shown to have poor performance at the upper and lower limits of the FT4 reference interval. The purpose of this pilot study was to investigate the percentage of individuals classified as having subclinical hypothyroidism with a standard immunoassay, that actually have low free thyroid hormone levels by mass spectrometry measurements. Outpatient samples with elevated TSH values and normal FT4 concentrations as per standard immunoassay methods were collected. FT4 and free triiodothyronine (FT3) analyses were performed on these samples using liquid chromatography-tandem mass spectrometry (LC-MS/MS). Sixty five percent (n=26) of patients (n=40) had (LC-MS/MS) FT4 or FT3 or both FT4 and FT3 values below mass spectrometry reference limits. Our findings indicate that the direct analogue immunoassay method for FT4 measurement results in a significant proportion of patients being misclassified as having subclinical hypothyroidism. Published by Elsevier B.V.

Sandstone and shale compaction curves derived from sonic and gamma ray logs in offshore wells, North Slope, Alaska; parameters for basin modeling

USGS Publications Warehouse

Rowan, Elisabeth L.; Hayba, Daniel O.; Nelson, Philip H.; Burns, W. Matthew; Houseknecht, David W.

2003-01-01

Representative compaction curves for the principle lithologies are essential input for reliable models of basin history. Compaction curves influence estimates of maximum burial and erosion. Different compaction curves may produce significantly different thermal histories. Default compaction curves provided by basin modeling packages may or may not be a good proxy for the compaction properties in a given area. Compaction curves in the published literature span a wide range, even within one lithology, e.g., sandstone (see Panel 3). An abundance of geophysical well data for the North Slope, from both government and private sources, provides us with an unusually good opportunity to develop compaction curves for the Cretaceous-Tertiary Brookian sandstones, siltstones, and shales. We examined the sonic and gamma ray logs from 19 offshore wells (see map), where significant erosion is least likely to have occurred. Our data are primarily from the Cretaceous-Tertiary Brookian sequence and are less complete for older sequences. For each well, the fraction of shale (Vsh) at a given depth was estimated from the gamma ray log, and porosity was computed from sonic travel time. By compositing porosities for the near-pure sand (Vsh99%)from many individual wells we obtained data over sufficient depth intervals to define sandstone and shale 'master' compaction curves. A siltstone curve was defined using the sonic-derived porosities for Vsh values of 50%. These compaction curves generally match most of the sonic porosities with an error of 5% or less. Onshore, the curves are used to estimate the depth of maximum burial at the end of Brookian sedimentation. The depth of sonic-derived porosity profiles is adjusted to give the best match with the 'master' compaction curves. The amount of the depth adjustment is the erosion estimate. Using our compaction curves, erosion estimates on the North Slope range from zero in much of the offshore, to as much as 1500 ft along the coast, and to more than 10,000 ft in the foothills (Panel 3). Compaction curves provide an alternative to vitrinite reflectance for estimating erosion. Vitrinite reflectance data are often very sparse in contrast to well log data and are subject to inconsistencies when measurements are made by different labs. The phenomenon of 'recycling' can also make the reflectance values of dispersed vitrinite problematic for quantifying erosion. Recycling is suspected in dispersed vitrinite in North Slope rocks, particularly in the younger, Cretaceous-Tertiary section. The compaction curves defined here are being integrated into our burial history and thermal models to determine the timing of source rock maturation. An example on Panel 3 shows the results of calculating the maturity of the Shublik Fm. at the Tulaga well using two different sets of shale and siltstone compaction curves. Finally, accurate compaction curves improve a model's ability to realistically simulate the pressure regime during burial, including overpressures.

Initial Results of Gulf of Mexico Gas Hydrate Joint Industry Program Leg II Logging-While-Drilling Operations in Green Canyon Block 955

NASA Astrophysics Data System (ADS)

McConnell, D. R.; Boswell, R. M.; Collett, T. S.; Frye, M.; Shedd, W.; Mrozewski, S.; Guerin, G.; Cook, A.; Shelander, D.; Dai, J.; Dufrene, R.; Godfriaux, P. D.; Roy, R.; Jones, E.

2009-12-01

The Gulf of Mexico gas hydrates Joint Industry Project (the JIP), a cooperative research program between the US Department of Energy and an international industrial consortium under the leadership of Chevron, conducted its “Leg II” logging-while-drilling operations in April and May of 2009. GC 955 was one of three sites drilled during Leg II. Three holes were drilled at the GC 955 site. High-saturations of gas hydrate in sands were logged at two of the three holes. The gas hydrate targets at the GC 955 site are just basinward of the Sigsbee Escarpment and outboard of the Green Canyon embayment in a Late Pleistocene Mississippi Fan channel levee sequence (0.5Ma). At the GC 955 site, the sand prone channel levee sediments are uplifted by a salt diapir, faulting the channel levee facies as well as focusing hydrocarbon charge to them. The top of the channel is approximately 1000 ft below seafloor and the sand-prone interval is in excess of 700 ft thick. The site was prospective for gas hydrate primarily due to the observation that seismic indicators of gas charge terminated anomalously within the inferred sand interval along a horizon consistent with the base of gas hydrate stability. Seismic amplitude analysis, as well as rock-physics based inversions of the seismic data, were used to refine the potential high-saturation targets. The gas hydrate targets clustered within a four-way closure caused by salt uplift. Other targets, faulted, with evidence of fluid migration, were identified, on the periphery of the closure. Three holes, locations I, H, and Q, were drilled at site GC955. The data acquired consist of a comprehensive suite of high resolution LWD logs including gamma ray, density, porosity, sonic, and resistivity tools. No physical samples were taken in the field. At the I location, only four feet of pore fill gas hydrate was detected within the sandy reservoir facies. At the H location, gas hydrate in clays and thin sands was found above the target zone and 101 ft of high-saturation gas hydrate was found at the primary target. At the Q location, at least 53 ft of high-saturation gas hydrate was found at the primary target before drilling was aborted. The discovery of thick, highly saturated gas hydrate sands at the GC955 site validates that gas hydrate can be found in reservoir quality sands through the integration of geologic and geophysical data. The LWD acquired data provided unprecedented information on the nature of the sediments and the occurrence of gas hydrate in the Gulf of Mexico.

Geologic investigation of Playa Lakes, Tonopah Test Range, Nevada : data report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rautman, Christopher Arthur

Subsurface geological investigations have been conducted at two large playa lakes at the Tonopah Test Range in central Nevada. These characterization activities were intended to provide basic stratigraphic-framework information regarding the lateral distribution of ''hard'' and ''soft'' sedimentary materials for use in defining suitable target regions for penetration testing. Both downhole geophysical measurements and macroscopic lithilogic descriptions were used as a surrogate for quantitative mechanical-strength properties, although some quantitative laboratory strength measurements were obtained as well. Both rotary (71) and core (19) holes on a systematic grid were drilled in the southern half of the Main Lake; drill hole spacingsmore » are 300 ft north-south and 500-ft east-west. The drilled region overlaps a previous cone-penetrometer survey that also addressed the distribution of hard and soft material. Holes were drilled to a depth of 40 ft and logged using both geologic examination and down-hole geophysical surveying. The data identify a large complex of very coarse-grained sediment (clasts up to 8 mm) with interbedded finer-grained sands, silts and clays, underlying a fairly uniform layer of silty clay 6 to 12 ft thick. Geophysical densities of the course-grained materials exceed 2.0 g/cm{sup 2}, and this petrophysical value appears to be a valid discriminator of hard vs. soft sediments in the subsurface. Thirty-four holes, including both core and rotary drilling, were drilled on a portion of the much larger Antelope Lake. A set of pre-drilling geophysical surveys, including time-domain electromagnetic methods, galvanic resistivity soundings, and terrain-conductivity surveying, was used to identify the gross distribution of conductive and resistive facies with respect to the present lake outline. Conductive areas were postulated to represent softer, clay-rich sediments with larger amounts of contained conductive ground water. Initial drilling, consisting of cored drill holes to 100-ft (33-m) depth, confirmed both the specific surface geophysical measurements and the more general geophysical model of the subsurface lake facies. Good agreement of conductive regions with drill holes containing little to no coarse-grained sediments was observed, and vice-versa. A second phase of grid drilling on approximately 300-ft (100-m) centers was targeted a delineating a region of sufficient size containing essentially no coarse-grained ''hard'' material. Such a region was identified in the southwestern portion of Antelope Lake.« less

Diesel fuel oil for increasing mountain pine beetle mortality in felled logs

Treesearch

S. A. Mata; J. M. Schmid; D. A. Leatherman

2002-01-01

Diesel fuel oil was applied to mountain pine beetle (Dendroctonus ponderosae Hopkins) infested bolts of ponderosa pine (Pinus ponderosa Lawson) in early June. Just prior to the fuel oil application and 6 weeks later, 0.5 ft2 bark samples were removed from each bolt and the numbers of live beetles counted....

Capabilities Report 2012, West Desert Test Center

DTIC Science & Technology

2012-03-12

132 FT- IR Spectrometer...electronic system files, paper logs, production batch records, QA/QC data, and PCR data generated during a test. Data analysts also track and QC raw data...Advantage +SL bench-top freeze dryers achieve shelf temperatures as low as -57°C and condenser temperatures to -67°C. The bulk milling facility produces

Oklahoma forest industries, 1978

Treesearch

Victor A. Rudis; J. Greg Jones

1978-01-01

Oklahoma supplied 73 million cu ft of roundwood to forest industries in 1978, an increase of 13 percent since 1972, and 35 percent since 1975 (fig. 1). Pine made up four-fifths of the total. Sawlogs and pulpwood were the major products, accounting for 81 percent of the roundwood produced. Veneer logs accounted for 8 percent and the remainder was mostly posts.

Logging residues in principal forest types of the Northern Rocky Mountains

Treesearch

Robert E. Benson; Joyce A. Schlieter

1980-01-01

An estimated 466 million ft 3 of forest residue material (nonmerchantable, 3 inches diameter and larger) is generated annually in the Northern Rocky Mountains (Montana, Idaho, Wyoming). Extensive studies of residues in the major forest types show a considerable portion is suited for various products. The lodgepole pine type has the greatest potential for increased...

Lithostratigraphic and Hydrogeologic Characteristics of the Ordovician Sinnipee Group in the Vicinity of Waupun, Fond du Lac County, Wisconsin, 1995-96

USGS Publications Warehouse

Dunning, Charles P.; Yeskis, Douglas J.

2007-01-01

Three boreholes were drilled at a farm site near Waupun, Wis., to improve the understanding of regional hydrogeology of the Ordovician Sinnipee Group. At the site the Sinnipee Group is the uppermost bedrock unit and is found to be about 183 ft thick. On the basis of core descriptions by the Illinois State Geological Survey, the Sinnipee Group at the site comprises (stratigraphically lowest to highest) the Platteville Formation (about 51 ft thick), the Decorah Formation (about 14 ft thick), and the Galena Dolomite (about 119 ft thick). The Illinois State Geological Survey noted that hardgrounds were common in the rock core, some having stratigraphic significance. Four very well developed hardgrounds were identified, three of which were used as formation or member contacts. The hardground at about 797 ft NGVD 29 represents the top of the Platteville Formation, the hardground at about 754 ft represents the top of the Pecatonica Member of the Platteville Formation, and the hardground at about 746 ft represents the top of the Glenwood Formation. On the basis of samples collected from one borehole, the ground water at the site is of the calcium-magnesium bicarbonate type. Trichloroethene was detected in one sample at a concentration of 1 ?g/L, and the concentration of antimony in one sample exceeded the U.S. Environmental Protection Agency (USEPA) Primary Drinking Water Standard. Other water samples contained aluminum and sodium in concentrations that exceeded the USEPA Secondary Drinking Water Standard and the USEPA Drinking Water Equivalent Level, respectively. Samples from various depths contained concentrations of iron, manganese, or dissolved manganese that were near or exceeded the USEPA Secondary Drinking Water Standard. The cross-borehole radar tomography data show differences in velocity and attenuation among the three major units in the Sinnipee Group. Matrix porosity measured in rock-core samples correlates well with these velocity and attenuation tomograms. The Galena Dolomite has the lowest mean porosity at 2.4 percent (7 samples) and is represented in the tomograms as generally having the lowest attenuation and greatest velocity. Below the Galena Dolomite is a transition to a zone with the greatest attenuation and lowest velocity on the tomograms. The rock core shows this interval to be the shaley dolomite of the Decorah Formation which has a mean porosity of 8.3 percent (2 samples). Below the Decorah Formation, the Platteville Formation has a mean porosity of 3.6 percent (6 samples) and is represented in the tomograms as having velocity and attenuation generally intermediate between the Galena Dolomite and the Decorah Formation. The evaluation of the single-hole directional ground-penetrating radar reflection survey in FL-800 identified 15 reflectors (secondary permeability features). Some of the reflectors do correlate with fractures and partings noted on geophysical logs and rock core; however, many additional fractures and partings identified by the televiewer log and/or core description were not measured by the borehole radar survey. Horizontal or sub-horizontal reflectors (bedding-plane partings) which do correlate with indications of bedding-plane partings on the acoustic televiewer intersect the borehole at about 917 ft, 907 ft, 870 ft, 805 ft, and 797 ft. The flowmeter profiles indicate that water entering and exiting the boreholes at seven bedding-plane partings accounts for most of the total borehole transmissivity. The flowmeter profiles in all three boreholes show that more than 90 percent of the total borehole transmissivity is provided by bedding-plane partings found at 870 ft and higher stratigraphically within the Galena Dolomite. Static water levels were measured in selected intervals of the three boreholes, and vertical hydraulic gradients were estimated by comparing levels in adjacent intervals. Gradients were found to be almost uniformly downward, ranging from -0.040 to -1.251 ft/ft. On th

Completion Report for Well ER-20-12: Corrective Action Units 101 and 102: Central and Western Pahute Mesa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wurtz, Jeff

2016-08-01

Well ER-20-12 was drilled for the U.S. Department of Energy, Nevada National Security Administration Nevada Field Office in support of the Underground Test Area Activity. The well was drilled from October 2015 to January 2016 as an addition to the Central and Western Pahute Mesa corrective action units 101 and 102 the Phase II drilling program. Well ER-20-12 was identified based on recommendations of the Pahute Mesa Guidance Team as a result of anomalous tritium detections in groundwater samples collected from Well PM-3 in 2011 and 2013. The primary purpose of the well was to provide information on the hydrogeologymore » in the area downgradient of select underground tests on Western Pahute Mesa and define hydraulic properties in the saturated Tertiary volcanic rocks. The main 46.99-centimeter (cm) (18.5-inch [in.]) borehole was drilled to a depth of 765.14 meters (m) (2,510.3 ft) and the hole opened to 66.04 cm (26 in.); followed by the 50.80-cm (20-in.) surface casing, which was installed and sealed with cement; and a piezometer (p4) was set in the Timber Mountain welded-tuff aquifer (TMWTA) between the casing and the open borehole. The borehole was continued with a 46.99-cm (18.5-in.) drill bit to a depth of 1,326.53 m (4,352.16 ft), and an intermediate 24.44-cm (9.625-in.) casing was installed and sealed to 1,188.72 m (3,900.00 ft) A piezometer (p3) was installed across the Calico Hills zeolitic composite unit (CHZCM) (lava-flow aquifer [LFA]) in the annulus of the open borehole. Two additional piezometers were installed and completed between the intermediate casing and the borehole wall, one (p2) in the CHZCM and one (p1) in the Belted Range aquifer (BRA). The piezometers are set to monitor groundwater properties in the completed intervals. The borehole was continued with a 21.59-cm (8.5-in.) drill bit to a total depth of 1,384.80 m (4,543.33 ft), and the main completion 13.97-cm (5.5-in.) casing was installed in the open borehole across the Pre-Belted Range composite unit (PBRCM). Data collected during hole construction include composite drill cutting samples collected every 3.0 m (10 ft), geophysical logs, hydrophysical logs, percussion core samples, water-quality measurements (including tritium), and water-level measurements. The well penetrated 1,384.4 m (4,543.33 ft) of Tertiary volcanic rocks. The stratigraphy and lithology were generally as expected with one noted exception. A thick lava-flow and related ash-flow tuffs were identified as Calico Hills Formation (Th), and no Crater Flat units were noted. Additionally, many of the Thirsty Canyon and Timber Mountain units were thicker than expected. Fluid levels measured in the borehole during drilling are the following: (1) on November 2, 2015, Navarro measured the fluid level in the borehole at a depth of 492.33 m (1,615.25 ft) below ground surface (bgs); (2) Schlumberger and COLOG recorded fluid levels during geophysical logging on November 4 and 5, 2015, at a depth of 492.86 m (1,617 ft) and 492.25 m (1,615 ft) bgs, respectively; and (3) on December 4, 2015, COLOG and Navarro measured fluid level in the 20-in. casing with an open borehole to 1,326.54 m (4,352.16 ft) bgs at 575.77 m (1,889.00 ft) and 574.03 m (1,883.3 ft) bgs, respectively. These and subsequent water-level measurements indicate a potential head difference of greater than 76.2 m (250 ft) for groundwater in aquifers above and below the Upper Paintbrush confining unit (UPCU). As expected, tritium was occasionally measured above the Safe Drinking Water Act limit (20,000 picocuries per liter [pCi/L]). Lab analysis on four bailed samples and taken from the undeveloped well indicate that the tritium activities average approximately 36,545 pCi/L. All Fluid Management Plan (FMP) requirements for Well ER-20-12 were met. Analysis of monitoring samples and FMP confirmatory samples indicate that fluids generated during drilling at ER-20-12 met the FMP criteria for discharge to the lined sump and designated infiltration area. All sanitary and hydrocarbon waste generated was properly handled and disposed of.« less

Tactical Wheeled Vehicle Survivability: Results of Experiments to Quantify Aboveground Impulse

DTIC Science & Technology

2010-03-01

in each testbed are pre- sented in Table 4.7. For all the clay soil experiments, the mean value of wet density was 121.2 lb/ft3, and the mean value...4.7. Summary of clay soil test series. Experiment Number Charge Position Avg Wet Density , lb/ft3 Avg Dry Density , lb/ft3 Avg Water... Clay soil ................................................................................................................................... 81

26 CFR 1.684-2 - Transfers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 1, 2007, at a time when the fair market value of the property is 1100X, I transfers the property to... market value of 500X and an adjusted basis of 100X to FT. At the time of the transfer, FT has no U.S... time of the transfer by DT to FT. Example 2. Transfer by a foreign trust. On January 1, 2001, A...

26 CFR 1.684-2 - Transfers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 1, 2007, at a time when the fair market value of the property is 1100X, I transfers the property to... market value of 500X and an adjusted basis of 100X to FT. At the time of the transfer, FT has no U.S... time of the transfer by DT to FT. Example 2. Transfer by a foreign trust. On January 1, 2001, A...

26 CFR 1.684-2 - Transfers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 1, 2007, at a time when the fair market value of the property is 1100X, I transfers the property to... market value of 500X and an adjusted basis of 100X to FT. At the time of the transfer, FT has no U.S... time of the transfer by DT to FT. Example 2. Transfer by a foreign trust. On January 1, 2001, A...

Ratio of serum free triiodothyronine to free thyroxine in Graves' hyperthyroidism and thyrotoxicosis caused by painless thyroiditis.

PubMed

Yoshimura Noh, Jaeduk; Momotani, Naoko; Fukada, Shuji; Ito, Koichi; Miyauchi, Akira; Amino, Nobuyuki

2005-10-01

The serum T3 to T4 ratio is a useful indicator for differentiating destruction-induced thyrotoxicosis from Graves' thyrotoxicosis. However, the usefulness of the serum free T3 (FT3) to free T4 (FT4) ratio is controversial. We therefore systematically evaluated the usefulness of this ratio, based on measurements made using two widely available commercial kits in two hospitals. Eighty-two untreated patients with thyrotoxicosis (48 patients with Graves' disease and 34 patients with painless thyroiditis) were examined in Kuma Hospital, and 218 patients (126 with Graves' disease and 92 with painless thyroiditis) and 66 normal controls were examined in Ito Hospital. The FT3 and FT4 values, as well as the FT3/FT4 ratios, were significantly higher in the patients with Graves' disease than in those with painless thyroiditis in both hospitals, but considerable overlap between the two disorders was observed. Receiver operating characteristic (ROC) curves for the FT3 and FT4 values and the FT3/FT4 ratios of patients with Graves' disease and those with painless thyroiditis seen in both hospitals were prepared, and the area under the curves (AUC), the cut-off points for discriminating Graves' disease from painless thyroiditis, the sensitivity, and the specificity were calculated. AUC and sensitivity of the FT(3)/FT(4) ratio were smaller than those of FT(3) and FT(4) in both hospitals. The patients treated at Ito hospital were then divided into 4 groups according to their FT4 levels (A: < or =2.3, B: >2.3 approximately < or =3.9, C: 3.9 approximately < or =5.4, D: >5.4 ng/dl), and the AUC, cut-off points, sensitivity, and specificity of the FT(3)/FT(4) ratios were calculated. The AUC and sensitivity of each group increased with the FT4 levels (AUC: 57.8%, 72.1%, 91.1%, and 93.4%, respectively; sensitivity: 62.6%, 50.0%, 77.8%, and 97.0%, respectively). The means +/- SE of the FT3/FT4 ratio in the Graves' disease groups were 3.1 +/- 0.22, 3.1 +/- 0.09, 3.2 +/- 0.06, and 3.1 +/- 0.07, respectively, versus 2.9 +/- 0.1, 2.6 +/- 0.07, 2.5 +/- 0.12, and 2.3 +/- 0.15, respectively, in the painless thyroiditis groups. In the painless thyroiditis patients, the difference in the FT3/FT4 ratio between group A and group D was significant (p<0.05). Thus, the FT3/FT4 ratio in patients with Graves' disease likely remains unchanged as the FT4 level rises, whereas this ratio decreases as the FT4 level rises in patients with painless thyroiditis. In conclusion, the FT3/FT4 ratios of patients with painless thyroiditis overlapped with those of patients with Graves' disease. However, this ratio was useful for differentiating between these two disorders when the FT4 values were high.

STRETCH IN A BOREHOLE CABLE AND ITS POSSIBLE EFFECTS ON THE OPERATION OF BOREHOLE LOGGING EQUIPMENT TYPE 1417A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, D.; Cole, H.A.G.

1958-11-01

A curious effect was observed during the operation of Bcrehole Logging Equipment Type 1417A in Rhodesia and Swaziland. With the probe submerged in water at depths greater than 150 ft vertical motion or light jerking of the cable produced spurious high count rates on the ratemeter. It has been suggested that voltage pulses which would be necessary to produce this effect, may be caused by changes in the length and hence capacity of the charged concentric cable connector prcduced under load conditions. This memorandum analyzes possible effects of cable stretch on instrument performance. (auth)

Determining water saturation in diatomite using wireline logs, Lost Hills field, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bilodeau, B.J.

1995-12-31

There is a long-held paradigm in the California oil industry that wireline log evaluation does not work in Monterey Formation lithologies. This study demonstrates that it is possible to calculate accurate oil saturation from wireline log data in the diatomite reservoir at Lost Hills field, California. The ability to calculate simple but accurate oil saturation is important because it allows field management teams to map pay, plan development and waterflood programs, and make estimates of reserves more accurate than those based on core information alone. Core data from eight wells were correlated with modern resistivity and porosity logs, incorporating moremore » than 2000 ft of reservoir section. Porosity was determined from bulk density and water saturation was determined using the Archie equation. Crossplots of corrected core oil saturation versus Archie oil saturation (1-S{sub w}) confirm the accuracy of the algorithm. Improvements in the accuracy and precision of the calculated oil saturation will require more detailed reservoir characterization to take into account lithologic variation.« less

An artificial intelligence approach to lithostratigraphic correlation using geophysical well logs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olea, R.A.; Davis, J.C.

1986-01-01

Computer programs for lithostratigraphic correlation of well logs have achieved limited success. Their algorithms are based on an oversimplified view of the manual process used by analysts to establish geologically correct correlations. The programs experience difficulties if the correlated rocks deviate from an ideal geometry of perfectly homogeneous, parallel layers of infinite extent. Artificial intelligence provides a conceptual basis for formulating the task of lithostratigraphic correlation, leading to more realistic procedures. A prototype system using the ''production rule'' approach of expert systems successfully correlates well logs in areas of stratigraphic complexity. Two digitized logs are used per well, one formore » curve matching and the other for lithologic comparison. The software has been successfully used to correlate more than 100,000 ft (30 480 m) of section, through clastic sequences in Louisiana and through carbonate sequences in Kansas. Correlations have been achieved even in the presence of faults, unconformities, facies changes, and lateral variations in bed thickness.« less

Superallowed Beta Decay Studies at TRIUMF --- Nuclear Structure and Fundamental Symmetries

NASA Astrophysics Data System (ADS)

Zganjar, E. F.; Achtzehn, T.; Albers, D.; Andreoiu, C.; Andreyev, A. N.; Austin, R. A. E.; Ball, G. C.; Behr, J. A.; Biosvert, G. C.; Bricault, P.; Bishop, S.; Chakrawarthy, R. S.; Churchman, R.; Cross, D.; Cunningham, E.; D'Auria, J. M.; Dombsky, M.; Finlay, P.; Garrett, P. E.; Grinyer, G. F.; Hackman, G.; Hanemaayer, V.; Hardy, J. C.; Hodgson, D. F.; Hyland, B.; Iacob, V.; Klages, P.; Koopmans, K. A.; Kulp, W. D.; Lassen, J.; Lavoie, J. P.; Leslie, J. R.; Linder, T.; MacDonald, J. A.; Mak, H.-B.; Melconian, D.; Morton, A. C.; Ormand, W. E.; Osborne, C. J.; Pearson, C. J.; Pearson, M. R.; Phillips, A. A.; Piechaczek, A.; Ressler, J.; Sarazin, F.; Savard, G.; Schumaker, M. A.; Scraggs, H. C.; Svensson, C. E.; Valiente-Dobon, J. J.; Towner, I. S.; Waddington, J. C.; Walker, P. M.; Wendt, K.; Wood, J. L.

2007-04-01

Precision measurement of the beta -decay half-life, Q-value, and branching ratio between nuclear analog states of Jpi = 0+ and T=1 can provide critical and fundamental tests of the Standard Model's description of electroweak interactions. A program has been initiated at TRIUMF-ISAC to measure the ft values of these superallowed beta transitions. Two Tz = 0, A > 60 cases, 74Rb and 62Ga, are presented. These are particularly relevant because they can provide critical tests of the calculated nuclear structure and isospin-symmetry breaking corrections that are predicted to be larger for heavier nuclei, and because they demonstrate the advance in the experimental precision on ft at TRIUMF-ISAC from 0.26% for 74Rb in 2002 to 0.05% for 62Ga in 2006. The high precision world data on experimental ft and corrected Ft values are discussed and shown to be consistent with CVC at the 10-4 level, yielding an average Ft = 3073.70(74) s. This Ft leads to Vud = 0.9737(4) for the up-down element of the Standard Model's CKM matrix. With this value and the Particle Data Group's 2006 values for Vus and Vub, the unitarity condition for the CKM matrix is met. Additional measurements and calculations are needed, however, to reduce the uncertainties in that evaluation. That objective is the focus of the continuing program on superallowed-beta decay at TRIUMF-ISAC.

High-Precision Half-Life Measurement for the Superallowed β+ Emitter 22Mg

NASA Astrophysics Data System (ADS)

Dunlop, Michelle

2017-09-01

High precision measurements of the Ft values for superallowed Fermi beta transitions between 0+ isobaric analogue states allow for stringent tests of the electroweak interaction. These transitions provide an experimental probe of the Conserved-Vector-Current hypothesis, the most precise determination of the up-down element of the Cabibbo-Kobayashi-Maskawa matrix, and set stringent limits on the existence of scalar currents in the weak interaction. To calculate the Ft values several theoretical corrections must be applied to the experimental data, some of which have large model dependent variations. Precise experimental determinations of the ft values can be used to help constrain the different models. The uncertainty in the 22Mg superallowed Ft value is dominated by the uncertainty in the experimental ft value. The adopted half-life of 22Mg is determined from two measurements which disagree with one another, resulting in the inflation of the weighted-average half-life uncertainty by a factor of 2. The 22Mg half-life was measured with a precision of 0.02% via direct β counting at TRIUMF's ISAC facility, leading to an improvement in the world-average half-life by more than a factor of 3.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rush, Jason; Holubnyak, Yevhen; Watney, Willard

This DOE-funded project evaluates the utility of seismic volumetric curvature (VC) for predicting stratal and structural architecture diagnostic of paleokarst reservoirs. Of special interest are applications geared toward carbon capture, utilization, and storage (CCUS). VC has been championed for identifying faults (offset <¼ λ) that cannot be imaged by conventional 3-D seismic attributes such as coherence. The objective of this research was to evaluate VC-techniques for reducing uncertainties in reservoir compartmentalization studies and seal risk assessments especially for saline aquifers. A 2000-ft horizontal lateral was purposefully drilled across VC-imaged lineaments—interpreted to record a fractured and a fault-bounded doline—to physically confirmmore » their presence. The 15-mi² study area is located in southeastern Bemis-Shutts Field, which is situated along the crest of the Central Kansas Uplift (CKU) in Ellis County, Kansas. The uppermost Arbuckle (200+ ft) has extensive paleokarst including collapsed paleocaverns and dolines related to exceedingly prolonged pre-Simpson (Sauk–Tippecanoe) and/or pre-Pennsylvanian subaerial exposure. A lateral borehole was successfully drilled across the full extent (~1100 ft) of a VC-inferred paleokarst doline. Triple combo (GR-neutron/density-resistivity), full-wave sonic, and borehole micro-imager logs were successfully run to TD on drill-pipe. Results from the formation evaluation reveal breccias (e.g., crackle, mosaic, chaotic), fractures, faults, vugs (1-6"), and unaffected host strata consistent with the pre-spud interpretation. Well-rounded pebbles were also observed on the image log. VC-inferred lineaments coincide with 20–80-ft wide intervals of high GR values (100+ API), matrix-rich breccias, and faults. To further demonstrate their utility, VC attributes are integrated into a geocellular modeling workflow: 1) to constrain the structural model; 2) to generate facies probability grids, and; 3) to collocate petrophysical models to separate-vug rock fabrics along solution-enlarged fault and fracture systems. Simulation-based studies demonstrate a potential alternative field development model for developing CO 2 storage sites that target carbonate reservoirs overprinted by paleokarst. Simulation results for this complex reservoir indicate that individual fault blocks could function as discrete containers for CO 2 storage thereby reducing the risk of plume migration outside the legally defined extent of the permitted storage site. Vertically extensive, anastomosing, solution-enlarged fault/fracture systems — infilled by clay-rich sediments — would operate as non-to-low permeability vertical "curtains" that restrict CO 2 movement beyond the confines of the CO 2 storage site. Such a location could be developed in a checker-board fashion with CO 2 injection operations occurring in one block and surveillance operations occurring in the adjacent block. Such naturally partitioned reservoirs may be ideal candidates for reducing risks associated with CO 2 plume breakthrough.« less

Polychlorinated biphenyl concentrations, congener profiles, and ratios in the fat tissue, eggs, and plasma of snapping turtles (Chelydra s. serpentina) from the Ohio Basin of Lake Erie, USA.

PubMed

Dabrowska, H; Fisher, S W; Estenik, J; Kidekhel, R; Stromberg, P

2006-08-01

Concentrations and profiles of polychlorinated biphenyls (PCBs) were determined in three tissues of adult snapping turtles (Chelydra serpentina serpentina) from six locations in the Ohio Basin of Lake Erie to characterize tissue variation and geographic trends. The locations included the Ohio Areas of Concern, i.e., the Ashtabula, Black, and Maumee Rivers; the Ottawa River near Toledo; and two reference sites. Mean total PCBs were greatest in turtles from the Ottawa River followed by the Maumee, Ashtabula, and Black Rivers. All three types of samples-fat tissue (FT), eggs, and plasma-showed the same geographic trend in PCB levels. On a wet-weight basis, mean concentrations ranged from 2,148 to 18,669 ng/g in FT, from 183 to 3,683 ng/g in eggs, and from 18 to 201 ng/g in plasma. Across all sites, total PCB concentrations between the tissues were significantly correlated (0.001 < p < 0.005; Pearson correlation coefficient (r ( P )) was between 0.720 and 0.954). Two distinctly different profiles with respect to relative congener and homologue concentrations were found among the sites. One that included four of the six sites examined was characterized by hexa-chlorobiphenyl (hexa-CB) dominance followed by hepta-CBs, with PCBs no. 138 + 163, 153 + 132 + 105, and 180 being the most abundant congeners. The second profile, specific for turtles from the Ottawa River, was different from the first in that tetra-CBs were the most abundant congeners followed by hexa-CBs. Analysis of variance (ANOVA) indicated significant intertissue differences in the PCB homologue profiles, i.e., FT had a higher percentage of hepta-, octa-, and nona-CBs compared with eggs and plasma, whereas eggs showed a higher percentage of hexa-CBs. At any listed location, FT, eggs, and plasma had the same congener profile. An intertissue distribution of lipid-normalized individual congener concentrations examined by regression analyses revealed significant egg-FT, egg-plasma, and FT-plasma relations for >40 congeners (0.001 < p < 0.05). The distribution ratios determined for these congeners from the slope of the regression lines averaged 1.235 +/- 0.279, 0.430 +/- 0.170, and 0.387 +/- 0.115, respectively. The plasma wet weight-FT lipid-normalized concentration ratios for these congeners averaged 0.012 +/- 0.006. Both egg-FT and plasma wet weight-FT lipid-normalized ratios regressed against log K(ow) showed significant decreases, with increasing log K(ow), indicating greater accumulation of highly chlorinated congeners in FT than in other compartments. The estimated 2,3,7,8-tetrachlorodibenzo-p-dioxin toxic equivalents ranged from 0.007 ng/g at reference sites to 0.060 ng/g at contaminated sites and from 0.099 to 1.992 ng/g in plasma and eggs, respectively. In both plasma and eggs, coplanar-CBs were the major contributors to total toxic equivalents (TEQs). Eggs from all contaminated sites had TEQs that exceeded the lowest observed effect level TEQs proposed for bald eagle chicks, in addition to high SigmaPCB levels at some of these sites, especially the Ottawa and Maumee River sites, indicate potentially increased risk to turtles and possibly other wildlife species inhabiting these ecosystems. Significant correlations of total PCBs and individual congeners between FT, eggs, and plasma indicate that blood sampling can provide a good nonlethal measure of PCB exposure and can be used to monitor environmental contamination.

Integration of seismic interpretation and petrophysical studies on Hawaz Formation in J-field NC-186 concession, Northwest Murzuq basin, Libya

NASA Astrophysics Data System (ADS)

Mohamed, A. K.; Selim, E. I.; Kashlaf, A.

2016-12-01

This study has been carried out by the integration of seismic interpretations and the well-logging analysis of ten wells distributed in J-field of concession NC-186, Murzuq basin, Libya. Twenty (3D) seismic lines and ten wells have been analyzed. The results of this study indicated that, the main reservoir in this concession is Hawaz Formation. Hawaz has been split into 8 units with a subdivision of Hawaz H4 into three subunits with the objective of better characterization of the three general fine upward intervals. The lower interval of H4 zone presents the better reservoir properties. The depth of reflector H4 ranges from 4100 ft in the northwestern part of the study area and increases to 4600 ft in the southeastern part of the study area. In this study, the outline of the Hawaz paleohighs which is NC-186 Field ;J; is generally trending in the NW-SE direction. The well logging analysis particularly quick look interpretation indicates that Hawaz Formation in the studied wells is mainly oil-bearing with some water-bearing sand levels at the horizons from H4 to and H6 which are potentially the main reservoirs. The water bearing zones are beyond these horizons starting from the sub-horizon H6c and the oil water contact is probably at depth 4495 ft. The crossplot of porosity-saturation for H5 and H6b indicates firmly that these horizons are indeed at irreducible state and will produce mainly oil as indicated in J4-NC186 well, while the crossplot of H8 shows wide scattering of points which is the main characteristic for water producing horizon. The depth of Hawaz Formation H4 is more than 4160 ft in J4, J12 and J16 wells in the northwestern parts of this field and increases to 4400 in the central part of the concession at well J1.

Logging intensity impact on small oak seedling survival and growth on the Cumberland Plateau in northeastern Alabama

Treesearch

Callie J. Schweitzer; Daniel C. Dey

2013-01-01

Ground disturbance caused by forest harvest operations can negatively impact oak regeneration. On the Cumberland Plateau, for successful regeneration, managers often must rely on very small (less than a ft in height) oak advance reproduction that is susceptible to disturbance by harvesting equipment. Furthermore, sites on the Plateau top are often harvested when...

Slash pine rootwood in flakeboard

Treesearch

E.T. Howard

1974-01-01

Flakes 3 Inches along the grain. 3/8-inch wide, and 0.02 inch thick were machined from the taproots (with 6-inch-high stump) and second logs at eight 31-year-old slash pines. Specific gravity (O.D. weight, green volume) of stems averaged 0.52; rootwood averaged 0.43 and decreased sharply with depth below ground. Forty-four-lb./cu. ft. structural-type particleboards...

Amplitude and Frequency Experimental Field Measurements of a Rotating-Imbalance Seismic Source Associated with Changes in Lithology Surrounding a Borehole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stephen R. Novascone; Michael J. Anderson; David M. Weinberg

2003-10-01

Field measurements of the vibration amplitude of a rotating-imbalance seismic source in a liquid-filled borehole are described. The borehole was a cased oil well that had been characterized by gamma-ray cement bond and compensated neutron litho-density/gamma-ray logs. The well logs indicated an abrupt transition from shale to limestone at a depth of 2638 ft. The vibration amplitude and frequency of a rotating-imbalance seismic source was measured versus applied voltage as the source was raised from 2654 to 2618 ft through the shale–limestone transition. It was observed that the vibration amplitude changed by approximately 10% in magnitude and the frequency changedmore » approximately 15% as the source passed the shale–limestone transition. The measurements were compared to predictions provided by a two-dimensional analytical model of a rotating-imbalance source located in a liquid-filled bore hole. It was observed that the sensitivity of the experimentally measured vibration amplitude of the seismic source to the properties of the surrounding geologic media was an order of magnitude greater than that predicted by the two-dimensional analytical model.« less

[Prevalence and prognostic value of non-thyroidal illness syndrome among critically ill children].

PubMed

El-Ella, Sohair Sayed Abu; El-Mekkawy, Muhammad Said; El-Dihemey, Mohamed Abdelrahman

2018-04-05

Alterations in thyroid hormones during critical illness, known as non-thyroidal illness syndrome (NTIS), were suggested to have a prognostic value. However, pediatric data is limited. The aim of this study was to assess prevalence and prognostic value of NTIS among critically ill children. A prospective observational study conducted on 70 critically ill children admitted into pediatric intensive care unit (PICU). Free triiodothyronine (FT3), free thyroxine (FT4), and thyroid stimulating hormone (TSH) were measured within 24hours of PICU admission. Primary outcome was 30-day mortality. NTIS occurred in 62.9% of patients but it took several forms. The most common pattern was low FT3 with normal FT4 and TSH (25.7% of patients). Combined decrease in FT3, FT4, and TSH levels occurred in 7.1% of patients. An unusual finding of elevated TSH was noted in three patients, which might be related to disease severity. Low FT4 was significantly more prevalent among non-survivors compared with survivors (50% versus 19.2%, P=.028). NTIS independently predicted mortality (OR=3.91; 95% CI=1.006-15.19; P=.0491). Concomitant decrease in FT3, FT4, and TSH was the best independent predictor of mortality (OR=16.9; 95% CI=1.40-203.04; P=.026). TSH was negatively correlated with length of PICU stay (r s =-0.35, P=.011). FT3 level was significantly lower among patients who received dopamine infusion compared with those who did not receive it (2.1±0.66 versus 2.76±0.91pg/mL, P=.011). NTIS is common among critically ill children and appears to be associated with mortality and illness severity. Copyright © 2018. Publicado por Elsevier España, S.L.U.

Drilling history and stratigraphic correlation of Rose Run sandstone of northeastern Ohio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, C.C.

1988-08-01

To date, 40 known tests have penetrated the Knox unconformity in Ashtabula, Lake, Trumbull, Geauga, and Portage Counties, Ohio. Prior to 1980, there were only 22 tests. Of these, only 10 penetrated and logged rocks older than the Rose Run sandstone. In the period 1980-1986, two Rose Run discoveries were drilled, one in New Lyme Township of Ashtabula County and one in Burton Township of Geauga County. Both discovery wells have been offset. Attempts have been made to correlate these two areas with older tests in northeastern Ohio and with the Rose Run sandstones of Coshocton County. In northeastern Ohio,more » preliminary studies indicate a Rose Run sandstone and/or dolomite interval approximately 100 ft thick. The upper 50 ft is predominantly sandstone and the lower 50 ft changes locally from sandstone to dolomite. The upper sandy member can be correlated to the A, B, and C sandstone units of Coshocton County.« less

The Lead Crack Fatigue Lifting Framework

DTIC Science & Technology

2010-04-01

15000 20000 25000 30000 35000 40000 F-WELD Test Hours C ra ck d ep th (m m ) IPP (1) IPP (2) IPP (3) IPP ( 4 ) IPP (5) IPP ( 6 ) IPP (6_A) FASS 226 (2...FASS 226 ( 4 ) FASS 226 (5) FASS 226 (5L) FASS 226 ( 6 ) FASS 226 (6R) SIH_OBD_SPLICE SIH_FS238/239 (1) SIH_FS238/239 (2) SIH_FS238/239 (3) SIH_FS238/239...conservative. 0.001 0.01 0.1 1 10 0 1 2 3 4 5 6 CB9 RHS CB8 LHS CB12 LHS CB12 RHS CB1 LHS FT55 LHS FT55 RHS ST16 LHS ST16 RHS Log average FLEI Virtual test

Hydrogeology and water quality of the Floridan aquifer system and effect of Lower Floridan aquifer withdrawals on the Upper Floridan aquifer at Barbour Pointe Community, Chatham County, Georgia, 2013

USGS Publications Warehouse

Gonthier, Gerard; Clarke, John S.

2016-06-02

Two test wells were completed at the Barbour Pointe community in western Chatham County, near Savannah, Georgia, in 2013 to investigate the potential of using the Lower Floridan aquifer as a source of municipal water supply. One well was completed in the Lower Floridan aquifer at a depth of 1,080 feet (ft) below land surface; the other well was completed in the Upper Floridan aquifer at a depth of 440 ft below land surface. At the Barbour Pointe test site, the U.S. Geological Survey completed electromagnetic (EM) flowmeter surveys, collected and analyzed water samples from discrete depths, and completed a 72-hour aquifer test of the Floridan aquifer system withdrawing from the Lower Floridan aquifer.Based on drill cuttings, geophysical logs, and borehole EM flowmeter surveys collected at the Barbour Pointe test site, the Upper Floridan aquifer extends 369 to 567 ft below land surface, the middle semiconfining unit, separating the two aquifers, extends 567 to 714 ft below land surface, and the Lower Floridan aquifer extends 714 to 1,056 ft below land surface.A borehole EM flowmeter survey indicates that the Upper Floridan and Lower Floridan aquifers each contain four water-bearing zones. The EM flowmeter logs of the test hole open to the entire Floridan aquifer system indicated that the Upper Floridan aquifer contributed 91 percent of the total flow rate of 1,000 gallons per minute; the Lower Floridan aquifer contributed about 8 percent. Based on the transmissivity of the middle semiconfining unit and the Floridan aquifer system, the middle semiconfining unit probably contributed on the order of 1 percent of the total flow.Hydraulic properties of the Upper Floridan and Lower Floridan aquifers were estimated based on results of the EM flowmeter survey and a 72-hour aquifer test completed in Lower Floridan aquifer well 36Q398. The EM flowmeter data were analyzed using an AnalyzeHOLE-generated model to simulate upward borehole flow and determine the transmissivity of water-bearing zones. Aquifer-test data were analyzed with a two-dimensional, axisymmetric, radial, transient, groundwater-flow model using MODFLOW–2005. The flowmeter-survey and aquifer-test simulations provided an estimated transmissivity of about 60,000 square feet per day for the Upper Floridan aquifer and about 5,000 square feet per day for the Lower Floridan aquifer.Water in discrete-depth samples collected from the Upper Floridan aquifer, middle semiconfining unit, and Lower Floridan aquifer during the EM flowmeter survey in August 2013 was low in dissolved solids. Tested constituents were in concentrations within established U.S. Environmental Protection Agency drinking water-quality criteria. Concentrations of measured constituents in water samples from Lower Floridan aquifer well 36Q398 collected at the end of the 72-hour aquifer test in November 2013 were generally higher than in the discrete-depth samples collected during EM flowmeter testing in August 2013 but remained within established drinking water-quality criteria.Water-level data for the aquifer test were filtered for external influences such as barometric pressure, earth-tide effects, and long-term trends to enable detection of small (less than 1 ft) water-level responses to aquifer-test withdrawal. During the 72-hour aquifer test, the Lower Floridan aquifer was pumped at a rate of 750 gallons per minute resulting in a drawdown response of 35.5 ft in the pumped well; 1.6 ft in the Lower Floridan aquifer observation well located about 6,000 ft west of the pumped well; and responses of 0.7, 0.6, and 0.4 ft in the Upper Floridan aquifer observation wells located about 36 ft, 6,000 ft, and 6,800 ft from the pumped well, respectively

High-throughput determination of octanol/water partition coefficients using a shake-flask method and novel two-phase solvent system.

PubMed

Morikawa, Go; Suzuka, Chihiro; Shoji, Atsushi; Shibusawa, Yoichi; Yanagida, Akio

2016-01-05

A high-throughput method for determining the octanol/water partition coefficient (P(o/w)) of a large variety of compounds exhibiting a wide range in hydrophobicity was established. The method combines a simple shake-flask method with a novel two-phase solvent system comprising an acetonitrile-phosphate buffer (0.1 M, pH 7.4)-1-octanol (25:25:4, v/v/v; AN system). The AN system partition coefficients (K(AN)) of 51 standard compounds for which log P(o/w) (at pH 7.4; log D) values had been reported were determined by single two-phase partitioning in test tubes, followed by measurement of the solute concentration in both phases using an automatic flow injection-ultraviolet detection system. The log K(AN) values were closely related to reported log D values, and the relationship could be expressed by the following linear regression equation: log D=2.8630 log K(AN) -0.1497(n=51). The relationship reveals that log D values (+8 to -8) for a large variety of highly hydrophobic and/or hydrophilic compounds can be estimated indirectly from the narrow range of log K(AN) values (+3 to -3) determined using the present method. Furthermore, log K(AN) values for highly polar compounds for which no log D values have been reported, such as amino acids, peptides, proteins, nucleosides, and nucleotides, can be estimated using the present method. The wide-ranging log D values (+5.9 to -7.5) of these molecules were estimated for the first time from their log K(AN) values and the above regression equation. Copyright © 2015 Elsevier B.V. All rights reserved.

Efficient Merge and Insert Operations for Binary Heaps and Trees

NASA Technical Reports Server (NTRS)

Kuszmaul, Christopher Lee; Woo, Alex C. (Technical Monitor)

2000-01-01

Binary heaps and binary search trees merge efficiently. We introduce a new amortized analysis that allows us to prove the cost of merging either binary heaps or balanced binary trees is O(l), in the amortized sense. The standard set of other operations (create, insert, delete, extract minimum, in the case of binary heaps, and balanced binary trees, as well as a search operation for balanced binary trees) remain with a cost of O(log n). For binary heaps implemented as arrays, we show a new merge algorithm that has a single operation cost for merging two heaps, a and b, of O(absolute value of a + min(log absolute value of b log log absolute value of b. log absolute value of a log absolute value of b). This is an improvement over O(absolute value of a + log absolute value of a log absolute value of b). The cost of the new merge is so low that it can be used in a new structure which we call shadow heaps. to implement the insert operation to a tunable efficiency. Shadow heaps support the insert operation for simple priority queues in an amortized time of O(f(n)) and other operations in time O((log n log log n)/f (n)), where 1 less than or equal to f (n) less than or equal to log log n. More generally, the results here show that any data structure with operations that change its size by at most one, with the exception of a merge (aka meld) operation, can efficiently amortize the cost of the merge under conditions that are true for most implementations of binary heaps and search trees.

Lumber yield and log values of Shasta red fir.

Treesearch

John B. Grantham; Douglas L. Hunt

1963-01-01

The value of lumber produced from each of 362 Shasta red fir logs of southern Oregon was determined through a cooperative study in 1960. Lumber grade yield from each log provided the basis for calculating the comparative value of each log grade-log diameter class, in accordance with grading and scaling practices used both east and west of the...

Immobilized Artificial Membrane HPLC Derived Parameters vs PAMPA-BBB Data in Estimating in Situ Measured Blood-Brain Barrier Permeation of Drugs.

PubMed

Grumetto, Lucia; Russo, Giacomo; Barbato, Francesco

2016-08-01

The affinity indexes for phospholipids (log kW(IAM)) for 42 compounds were measured by high performance liquid chromatography (HPLC) on two different phospholipid-based stationary phases (immobilized artificial membrane, IAM), i.e., IAM.PC.MG and IAM.PC.DD2. The polar/electrostatic interaction forces between analytes and membrane phospholipids (Δlog kW(IAM)) were calculated as the differences between the experimental values of log kW(IAM) and those expected for isolipophilic neutral compounds having polar surface area (PSA) = 0. The values of passage through a porcine brain lipid extract (PBLE) artificial membrane for 36 out of the 42 compounds considered, measured by the so-called PAMPA-BBB technique, were taken from the literature (P0(PAMPA-BBB)). The values of blood-brain barrier (BBB) passage measured in situ, P0(in situ), for 38 out of the 42 compounds considered, taken from the literature, represented the permeability of the neutral forms on "efflux minimized" rodent models. The present work was aimed at verifying the soundness of Δlog kW(IAM) at describing the potential of passage through the BBB as compared to data achieved by the PAMPA-BBB technique. In a first instance, the values of log P0(PAMPA-BBB) (32 data points) were found significantly related to the n-octanol lipophilicity values of the neutral forms (log P(N)) (r(2) = 0.782) whereas no significant relationship (r(2) = 0.246) was found with lipophilicity values of the mixtures of ionized and neutral forms existing at the experimental pH 7.4 (log D(7.4)) as well as with either log kW(IAM) or Δlog kW(IAM) values. log P0(PAMPA-BBB) related moderately to log P0(in situ) values (r(2) = 0.604). The latter did not relate with either n-octanol lipophilicity indexes (log P(N) and log D(7.4)) or phospholipid affinity indexes (log kW(IAM)). In contrast, significant inverse linear relationships were observed between log P0(in situ) (38 data points) and Δlog kW(IAM) values for all the compounds but ibuprofen and chlorpromazine, which behaved as moderate outliers (r(2) = 0.656 and r(2) = 0.757 for values achieved on IAM.PC.MG and IAM.PC.DD2, respectively). Since log P0(in situ) refer to the "intrinsic permeability" of the analytes regardless their ionization degree, no correction for ionization of Δlog kW(IAM) values was needed. Furthermore, log P0(in situ) were found roughly linearly related to log BB values (i.e., the logarithm of the ratio brain concentration/blood concentration measured in vivo) for all the analytes but those predominantly present at the experimental pH 7.4 as anions. These results suggest that, at least for the data set considered, Δlog kW(IAM) parameters are more effective than log P0(PAMPA-BBB) at predicting log P0(in situ) values for all the analytes. Furthermore, ionization appears to affect differently, and much more markedly, BBB passage of acids (yielding anions) than that of the other ionizable compounds.

National Wild Turkey Federation Programs

Treesearch

Rob Keck

2005-01-01

I recently read an article about several women who were preparing to sit 80 ft (25 m) above a forest floor in tree-sitting nets to protest a logging operation in Jefferson National Forest (Appalachia). Tree hugging is nothing new in this country. But did environmental activists know we have more forests now than we did in the 1920s? In 1920, we only had 735 million ac...

Low altitude wind shear statistics derived from measured and FAA proposed standard wind profiles

NASA Technical Reports Server (NTRS)

Dunham, R. E., Jr.; Usry, J. W.

1984-01-01

Wind shear statistics were calculated for a simulated data set using wind profiles proposed as a standard and compared to statistics derived from measured wind profile data. Wind shear values were grouped in altitude bands of 100 ft between 100 and 1400 ft, and in wind shear increments of 0.025 kt/ft between + or - 0.600 kt/ft for the simulated data set and between + or - 0.200 kt/ft for the measured set. No values existed outside the + or - 0.200 kt/ft boundaries for the measured data. Frequency distributions, means, and standard deviations were derived for each altitude band for both data sets, and compared. Also, frequency distributions were derived for the total sample for both data sets and compared. Frequency of occurrence of a given wind shear was about the same for both data sets for wind shears, but less than + or 0.10 kt/ft, but the simulated data set had larger values outside these boundaries. Neglecting the vertical wind component did not significantly affect the statistics for these data sets. The frequency of occurrence of wind shears for the flight measured data was essentially the same for each altitude band and the total sample, but the simulated data distributions were different for each altitude band. The larger wind shears for the flight measured data were found to have short durations.

High-precision QEC values of superallowed 0+ → 0+β-emitters 46Cr, 50Fe and 54Ni

NASA Astrophysics Data System (ADS)

Zhang, P.; Xu, X.; Shuai, P.; Chen, R. J.; Yan, X. L.; Zhang, Y. H.; Wang, M.; Litvinov, Yu. A.; Blaum, K.; Xu, H. S.; Bao, T.; Chen, X. C.; Chen, H.; Fu, C. Y.; He, J. J.; Kubono, S.; Lam, Y. H.; Liu, D. W.; Mao, R. S.; Ma, X. W.; Sun, M. Z.; Tu, X. L.; Xing, Y. M.; Yang, J. C.; Yuan, Y. J.; Zeng, Q.; Zhou, X.; Zhou, X. H.; Zhan, W. L.; Litvinov, S.; Audi, G.; Uesaka, T.; Yamaguchi, Y.; Yamaguchi, T.; Ozawa, A.; Sun, B. H.; Sun, Y.; Xu, F. R.

2017-04-01

Short-lived 46Cr, 50Fe and 54Ni were studied by isochronous mass spectrometry at the HIRFL-CSR facility in Lanzhou. The measured precision mass excesses (ME) of 46Cr, 50Fe and 54Ni are - 29471 (11) keV, - 34477 (6) keV and - 39278 (4) keV, respectively. The superallowed 0+ →0+β-decay Q values were derived to be QEC (46Cr) = 7604 (11) keV, QEC (50Fe) = 8150 (6) keV and QEC (54Ni) = 8731 (4) keV. The values for 50Fe and 54Ni are by one order of magnitude more precise than the adopted literature values. By combining the existing half-lives and branching ratios, we obtained the corrected Ft values to be Ft (50Fe) = 3103 (70) s and Ft (54Ni) = 3076 (50) s. The main contribution to the Ft uncertainties is now due to β-decay branching ratios, still, more high-precision measurements of the half-lives, the masses, and especially the branching ratios are needed in order to satisfy the requirements for a stringent CVC test.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wurtz, Jeffrey; Rehfeldt, Ken

Well ER-2-2 was drilled for the U.S. Department of Energy, Nevada National Security Administration Nevada Field Office in support of the Underground Test Area (UGTA) Activity. The well was drilled from January 17 to February 8, 2016, as part of the Corrective Action Investigation Plan (CAIP) for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada. The primary purpose of the well was to collect hydrogeologic data to evaluate uncertainty in the flow and transport conceptual model and its contamination boundary forecasts, and to detect radionuclides in groundwater from the CALABASH (U2av) underground test. Well ER-2-2 was notmore » completed as planned due to borehole stability problems. As completed, the well includes a piezometer (p1) to 582 meters (m) (1,909 feet [ft]) below ground surface (bgs) installed in the Timber Mountain lower vitric-tuff aquifer (TMLVTA) and a 12.25-inch (in.) diameter open borehole to 836 m (2,743 ft) bgs in the Lower tuff confining unit (LTCU). A 13.375-in. diameter carbon-steel casing is installed from the surface to a depth of 607 m (1,990 ft) bgs. Data collected during borehole construction include composite drill cutting samples collected every 3.0 m (10 ft), geophysical logs to a depth of 672.4 m (2,206 ft) bgs, water-quality measurements (including tritium), water-level measurements, and slug test data. The well penetrated 384.05 m (1,260 ft) of Quaternary alluvium, 541.93 m (1,778 ft) of Tertiary Volcanics (Tv) rocks, and 127.71 m (419 ft) of Paleozoic carbonates. The stratigraphy and lithology were generally as expected. However, several of the stratigraphic units were significantly thicker then predicted—principally, the Tunnel formation (Tn), which had been predicted to be 30 m (100 ft) thick; the actual thickness of this unit was 268.22 m (880 ft). Fluid depths were measured in the borehole during drilling as follows: (1) in the piezometer (p1) at 552.15 m (1,811.53 ft) bgs and (2) in the main casing (m1) at 551.69 m (1,810.01 ft) bgs. As expected, field measurements for tritium were above the Safe Drinking Water Act limit (20,000 picocuries per liter). All Fluid Management Plan requirements were met.« less

Comparison of low-altitude wind-shear statistics derived from measured and proposed standard wind profiles

NASA Technical Reports Server (NTRS)

Usry, J. W.

1983-01-01

Wind shear statistics were calculated for a simulated set of wind profiles based on a proposed standard wind field data base. Wind shears were grouped in altitude in altitude bands of 100 ft between 100 and 1400 ft and in wind shear increments of 0.025 knot/ft. Frequency distributions, means, and standard deviations for each altitude band were derived for the total sample were derived for both sets. It was found that frequency distributions in each altitude band for the simulated data set were more dispersed below 800 ft and less dispersed above 900 ft than those for the measured data set. Total sample frequency of occurrence for the two data sets was about equal for wind shear values between +0.075 knot/ft, but the simulated data set had significantly larger values for all wind shears outside these boundaries. It is shown that normal distribution in both data sets neither data set was normally distributed; similar results are observed from the cumulative frequency distributions.

Increased Oil Production and Reserves from Improved Completion Techniques in the Bluebell Field, Uinta Basin, Utah

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deo, M.D.; Morgan, C.D.

1999-04-28

The objective of the project is to increase oil production and reserves by the use of improved reservoir characterization and completion techniques in the Uinta Basin, Utah. To accomplish this objective, a two-year geologic and engineering characterization of the Bluebell field was conducted. The study evaluated surface and subsurface data, currently used completion techniques, and common production problems. It was determined that advanced case- and open-hole logs could be effective in determining productive beds and that stage-interval (about 500 ft [150 m] per stage) and bed-scale isolation completion techniques could result in improved well performance. In the first demonstration wellmore » (Michelle Ute well discussed in the previous technical report), dipole shear anisotropy (anisotropy) and dual-burst thermal decay time (TDT) logs were run before and isotope tracer log was run after the treatment. The logs were very helpful in characterizing the remaining hydrocarbon potential in the well. But, mechanical failure resulted in a poor recompletion and did not result in a significant improvement in the oil production from the well.« less

Stratigraphy and tectonic history of the Tucson Basin, Pima County, Arizona, based on the Exxon state (32)-1 well

USGS Publications Warehouse

Houser, Brenda B.; Peters, Lisa; Esser, Richard P.; Gettings, Mark E.

2004-01-01

The Tucson Basin is a relatively large late Cenozoic extensional basin developed in the upper plate of the Catalina detachment fault in the southern Basin and Range Province, southeastern Arizona. In 1972, Exxon Company, U.S.A., drilled an exploration well (Exxon State (32)-1) near the center of the Tucson Basin that penetrated 3,658 m (12,001 ft) of sedimentary and volcanic rocks above granitoid basement. Detailed study of cuttings and geophysical logs of the Exxon State well has led to revision of the previously reported subsurface stratigraphy for the basin and provided new insight into its depositional and tectonic history. There is evidence that detachment faulting and uplift of the adjacent Catalina core complex on the north have affected the subsurface geometry of the basin. The gravity anomaly map of the Tucson Basin indicates that the locations of subbasins along the north-trending axis of the main basin coincide with the intersection of this axis with west-southwest projections of synforms in the adjacent core complex. In other words, the subbasins overlie synforms and the ridges between subbasins overlie antiforms. The Exxon State well was drilled near the center of one of the subbasins. The Exxon well was drilled to a total depth of 3,827 m (12,556 ft), and penetrated the following stratigraphic section: Pleistocene(?) to middle(?) Miocene upper basin-fill sedimentary rocks (0-908 m [0-2,980 ft]) lower basin-fill sedimentary rocks (908-1,880 m [2,980-6,170 ft]) lower Miocene and upper Oligocene Pantano Formation (1,880-2,516 m [6,170-8,256 ft]) upper Oligocene to Paleocene(?) volcanic and sedimentary rocks (2,516-3,056 m [8,256-10,026 ft]) Lower Cretaceous to Upper Jurassic Bisbee Group (3,056-3,658 m [10,026-12,001 ft]) pre-Late Jurassic granitoid plutonic rock (3,658-3,827 m [12,001- 12,556 ft]). Stratigraphy and Tectonic History of the Tucson Basin, Pima County, Arizona, Based on the Exxon State (32)-1 Well The 1,880 m (6,170 ft) of basin-fill sedimentary rocks consist of alluvial-fan, alluvial-plain, and playa facies. The uppermost unit, a 341-m-thick (1,120-ft) lower Pleistocene and upper Pliocene alluvial-fan deposit (named the Cienega Creek fan in this study), is an important aquifer in the Tucson basin. The facies change at the base of the alluvial fan may prove to be recognizable in well data throughout much of the basin. The well data show that a sharp boundary at 908 m (2,980 ft) separates relatively unconsolidated and undeformed upper basin fill from denser, significantly faulted lower basin fill, indicating that there were two stages of basin filling in the Tucson basin as in other basins of the region. The two stages apparently occurred during times of differing tectonic style in the region. In the Tucson area the Pantano Formation, which contains an andesite flow dated at about 25 Ma, fills a syntectonic basin in the hanging wall of the Catalina detachment fault, reflecting middle Tertiary extension on the fault. The formation in the well is 636 m thick (2,086 ft) and consists of alluvial-fan, playa, and lacustrine sedimentary facies, a lava flow, and rock- avalanche deposits. Analysis of the geophysical logs indicates that a K-Ar date of 23.4 Ma reported previously for the Pantano interval of the well was obtained on selected cuttings collected from a rock-avalanche deposit near the base of the unit and, thus, does not date the Pantano Formation. The middle Tertiary volcanic and sedimentary rocks have an aggregate thickness of 540 m (1,770 ft). We obtained a new 40Ar/ 39Ar age of 26.91+0.18 Ma on biotite sampled at a depth of 2,584-2,609 m (8,478-8,560 ft) from a 169-m-thick (554-ft) silicic tuff in this interval. The volcanic rocks probably correlate with other middle Tertiary volcanic rocks of the area, and the sedimentary rocks may correlate with the Cloudburst and Mineta Formations exposed on the flanks of the San Pedro Basin to the northeast. The Bisbee Group in the Exxon well is 602 m (1,975 f

Completion summary for boreholes USGS 140 and USGS 141 near the Advanced Test Reactor Complex, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Twining, Brian V.; Bartholomay, Roy C.; Hodges, Mary K.V.

2014-01-01

In 2013, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, drilled and constructed boreholes USGS 140 and USGS 141 for stratigraphic framework analyses and long-term groundwater monitoring of the eastern Snake River Plain aquifer at the Idaho National Laboratory in southeast Idaho. Borehole USGS 140 initially was cored to collect continuous geologic data, and then re-drilled to complete construction as a monitor well. Borehole USGS 141 was drilled and constructed as a monitor well without coring. Boreholes USGS 140 and USGS 141 are separated by about 375 feet (ft) and have similar geologic layers and hydrologic characteristics based on geophysical and aquifer test data collected. The final construction for boreholes USGS 140 and USGS 141 required 6-inch (in.) diameter carbon-steel well casing and 5-in. diameter stainless-steel well screen; the screened monitoring interval was completed about 50 ft into the eastern Snake River Plain aquifer, between 496 and 546 ft below land surface (BLS) at both sites. Following construction and data collection, dedicated pumps and water-level access lines were placed to allow for aquifer testing, for collecting periodic water samples, and for measuring water levels. Borehole USGS 140 was cored continuously, starting from land surface to a depth of 543 ft BLS. Excluding surface sediment, recovery of basalt and sediment core at borehole USGS 140 was about 98 and 65 percent, respectively. Based on visual inspection of core and geophysical data, about 32 basalt flows and 4 sediment layers were collected from borehole USGS 140 between 34 and 543 ft BLS. Basalt texture for borehole USGS 140 generally was described as aphanitic, phaneritic, and porphyritic; rubble zones and flow mold structure also were described in recovered core material. Sediment layers, starting near 163 ft BLS, generally were composed of fine-grained sand and silt with a lesser amount of clay; however, between 223 and 228 ft BLS, silt with gravel was described. Basalt flows generally ranged in thickness from 3 to 76 ft (average of 14 ft) and varied from highly fractured to dense with high to low vesiculation. Geophysical and borehole video logs were collected during certain stages of the drilling and construction process at boreholes USGS 140 and USGS 141. Geophysical logs were examined synergistically with the core material for borehole USGS 140; additionally, geophysical data were examined to confirm geologic and hydrologic similarities between boreholes USGS 140 and USGS 141 because core was not collected for borehole USGS 141. Geophysical data suggest the occurrence of fractured and (or) vesiculated basalt, dense basalt, and sediment layering in both the saturated and unsaturated zones in borehole USGS 141. Omni-directional density measurements were used to assess the completeness of the grout annular seal behind 6-in. diameter well casing. Furthermore, gyroscopic deviation measurements were used to measure horizontal and vertical displacement at all depths in boreholes USGS 140 and USGS 141. Single-well aquifer tests were done following construction at wells USGS 140 and USGS 141 and data examined after the tests were used to provide estimates of specific-capacity, transmissivity, and hydraulic conductivity. The specific capacity, transmissivity, and hydraulic conductivity for well USGS 140 were estimated at 2,370 gallons per minute per foot [(gal/min)/ft)], 4.06 × 105 feet squared per day (ft2/d), and 740 feet per day (ft/d), respectively. The specific capacity, transmissivity, and hydraulic conductivity for well USGS 141 were estimated at 470 (gal/min)/ft, 5.95 × 104 ft2/d, and 110 ft/d, respectively. Measured flow rates remained relatively constant in well USGS 140 with averages of 23.9 and 23.7 gal/min during the first and second aquifer tests, respectively, and in well USGS 141 with an average of 23.4 gal/min. Water samples were analyzed for cations, anions, metals, nutrients, volatile organic compounds, stable isotopes, and radionuclides. Water samples from both wells indicated that concentrations of tritium, sulfate, and chromium were affected by wastewater disposal practices at the Advanced Test Reactor Complex. Most constituents in water from wells USGS 140 and USGS 141 had concentrations similar to concentrations in well USGS 136, which is upgradient from wells USGS 140 and USGS 141.

Short-time fractional Fourier methods for the time-frequency representation of chirp signals.

PubMed

Capus, Chris; Brown, Keith

2003-06-01

The fractional Fourier transform (FrFT) provides a valuable tool for the analysis of linear chirp signals. This paper develops two short-time FrFT variants which are suited to the analysis of multicomponent and nonlinear chirp signals. Outputs have similar properties to the short-time Fourier transform (STFT) but show improved time-frequency resolution. The FrFT is a parameterized transform with parameter, a, related to chirp rate. The two short-time implementations differ in how the value of a is chosen. In the first, a global optimization procedure selects one value of a with reference to the entire signal. In the second, a values are selected independently for each windowed section. Comparative variance measures based on the Gaussian function are given and are shown to be consistent with the uncertainty principle in fractional domains. For appropriately chosen FrFT orders, the derived fractional domain uncertainty relationship is minimized for Gaussian windowed linear chirp signals. The two short-time FrFT algorithms have complementary strengths demonstrated by time-frequency representations for a multicomponent bat chirp, a highly nonlinear quadratic chirp, and an output pulse from a finite-difference sonar model with dispersive change. These representations illustrate the improvements obtained in using FrFT based algorithms compared to the STFT.

Defect detection on hardwood logs using high resolution three-dimensional laser scan data

Treesearch

Liya Thomas; Lamine Mili; Clifford A. Shaffer; Ed Thomas; Ed Thomas

2004-01-01

The location, type, and severity of external defects on hardwood logs and skills are the primary indicators of overall log quality and value. External defects provide hints about the internal log characteristics. Defect data would improve the sawyer's ability to process logs such that a higher valued product (lumber) is generated. Using a high-resolution laser log...

Enhancing the properties of Fischer-Tropsch fuel produced from syngas over Co/SiO2 catalyst: Lubricity and Calorific Value

NASA Astrophysics Data System (ADS)

Doustdar, O.; Wyszynski, M. L.; Mahmoudi, H.; Tsolakis, A.

2016-09-01

Bio-fuel produced from renewable sources is considered the most viable alternatives for the replacement of mineral diesel fuel in compression ignition engines. There are several options for biomass derived fuels production involving chemical, biological and thermochemical processes. One of the best options is Fischer Tropsch Synthesis, which has an extensive history of gasoline and diesel production from coal and natural gas. FTS fuel could be one of the best solutions to the fuel emission due to its high quality. FTS experiments were carried out in 16 different operation conditions. Mini structured vertical downdraft fixed bed reactor was used for the FTS. Instead of Biomass gasification, a simulated N2 -rich syngas cylinder of, 33% H2 and 50% N2 was used. FT fuels products were analyzed in GCMS to find the hydrocarbon distributions of FT fuel. Calorific value and lubricity of liquid FT product were measured and compared with commercial diesel fuel. Lubricity has become an important quality, particularly for biodiesel, due to higher pressures in new diesel fuel injection (DFI) technology which demands better lubrication from the fuel and calorific value which is amount of energy released in combustion paly very important role in CI engines. Results show that prepared FT fuel has desirable properties and it complies with standard values. FT samples lubricities as measured by ASTM D6079 standard vary from 286μm (HFRR scar diameter) to 417μm which are less than limit of 520μm. Net Calorific value for FT fuels vary from 9.89 MJ/kg to 43.29 MJ/kg, with six of the samples less than EN 14213 limit of 35MJ/kg. Effect of reaction condition on FT fuel properties was investigated which illustrates that in higher pressure Fischer-Tropsch reaction condition liquid product has better properties.

Validity of electromyographic fatigue threshold as a noninvasive method for tracking changes in ventilatory threshold in college-aged men.

PubMed

Kendall, Kristina L; Smith, Abbie E; Graef, Jennifer L; Walter, Ashley A; Moon, Jordan R; Lockwood, Christopher M; Beck, Travis W; Cramer, Joel T; Stout, Jeffrey R

2010-01-01

The submaximal electromyographic fatigue threshold test (EMG(FT)) has been shown to be highly correlated to ventilatory threshold (VT) as determined from maximal graded exercise tests (GXTs). Recently, a prediction equation was developed using the EMG(FT) value to predict VT. The aim of this study, therefore, was to determine if this new equation could accurately track changes in VT after high-intensity interval training (HIIT). Eighteen recreationally trained men (mean +/- SD; age 22.4 +/- 3.2 years) performed a GXT to determine maximal oxygen consumption rate (V(O2)peak) and VT using breath-by-breath spirometry. Participants also completed a discontinuous incremental cycle ergometer test to determine their EMGFT value. A total of four 2-minute work bouts were completed to obtain 15-second averages of the electromyographic amplitude. The resulting slopes from each successive work bout were used to calculate EMG(FT). The EMG(FT) value from each participant was used to estimate VT from the recently developed equation. All participants trained 3 days a week for 6 weeks. Training consisted of 5 sets of 2-minute work bouts with 1 minute of rest in between. Repeated-measures analysis of variance indicated no significant difference between actual and predicted VT values after 3 weeks of training. However, there was a significant difference between the actual and predicted VT values after 6 weeks of training. These findings suggest that the EMG(FT) may be useful when tracking changes in VT after 3 weeks of HIIT in recreationally trained individuals. However, the use of EMG(FT) to predict VT does not seem to be valid for tracking changes after 6 weeks of HIIT. At this time, it is not recommended that EMG(FT) be used to predict and track changes in VT.

A law of the iterated logarithm for Grenander’s estimator

PubMed Central

Dümbgen, Lutz; Wellner, Jon A.; Wolff, Malcolm

2016-01-01

In this note we prove the following law of the iterated logarithm for the Grenander estimator of a monotone decreasing density: If f(t0) > 0, f′(t0) < 0, and f′ is continuous in a neighborhood of t0, then lim supn→∞(n2log logn)1/3(fn^(t0)−f(t0))=|f(t0)f′(t0)/2|1/32Malmost surely where M≡supg∈GTg=(3/4)1/3andTg≡argmaxu{g(u)−u2};here G is the two-sided Strassen limit set on R. The proof relies on laws of the iterated logarithm for local empirical processes, Groeneboom’s switching relation, and properties of Strassen’s limit set analogous to distributional properties of Brownian motion. PMID:28042197

Completion Summary for Well NRF-16 near the Naval Reactors Facility, Idaho National Laboratory, Idaho

USGS Publications Warehouse

Twining, Brian V.; Fisher, Jason C.; Bartholomay, Roy C.

2010-01-01

In 2009, the U.S. Geological Survey in cooperation with the U.S. Department of Energy's Naval Reactors Laboratory Field Office, Idaho Branch Office cored and completed well NRF-16 for monitoring the eastern Snake River Plain (SRP) aquifer. The borehole was initially cored to a depth of 425 feet below land surface and water samples and geophysical data were collected and analyzed to determine if well NRF-16 would meet criteria requested by Naval Reactors Facility (NRF) for a new upgradient well. Final construction continued after initial water samples and geophysical data indicated that NRF-16 would produce chemical concentrations representative of upgradient aquifer water not influenced by NRF facility disposal, and that the well was capable of producing sustainable discharge for ongoing monitoring. The borehole was reamed and constructed as a Comprehensive Environmental Response Compensation and Liability Act monitoring well complete with screen and dedicated pump. Geophysical and borehole video logs were collected after coring and final completion of the monitoring well. Geophysical logs were examined in conjunction with the borehole core to identify primary flow paths for groundwater, which are believed to occur in the intervals of fractured and vesicular basalt and to describe borehole lithology in detail. Geophysical data also were examined to look for evidence of perched water and the extent of the annular seal after cement grouting the casing in place. Borehole videos were collected to confirm that no perched water was present and to examine the borehole before and after setting the screen in well NRF-16. Two consecutive single-well aquifer tests to define hydraulic characteristics for well NRF-16 were conducted in the eastern SRP aquifer. Transmissivity and hydraulic conductivity averaged from the aquifer tests were 4.8 x 103 ft2/d and 9.9 ft/d, respectively. The transmissivity for well NRF-16 was within the range of values determined from past aquifer tests in other wells near NRF of 4.4 x 102 to 5.1 x 105 ft2/d. Water samples were analyzed for metals, nutrients, total organic carbon, volatile organic compounds, semi-volatile organic compounds, herbicides, pesticides, polychlorinated biphenols, and radionuclides. All chloride, nitrate, and sulfate concentrations were less than background concentrations for the eastern SRP aquifer north of the NRF. Concentrations in water samples for most of the organic compounds and radionuclides were less than the reporting limits and reporting levels.

Estimation of Koc values for deuterated benzene, toluene, and ethylbenzene, and application to ground water contamination studies.

PubMed

Poulson, S R; Drever, J I; Colberg, P J

1997-11-01

Sorption partition coefficients between water and organic carbon (Koc) for deuterated benzene, toluene, and ethylbenzene have been estimated by measuring values of the octanol-water partition coefficient (Kow) and HPLC retention factors (k1), which correlate closely to values of Koc. Measured values of log Kow for non-deuterated and deuterated toluene are 2.77 (+/- 0.02) and 2.78 (+/- 0.04), respectively, indicating that within experimental error, log Koc for deuterated and non-deuterated toluene are the same. The HPLC method provides greater precision, and yields values of delta log Koc (= log Koc [deuterated]-log Koc [non-deuterated]) of -0.021 (+/- 0.001) for benzene, -0.028 (+/- 0.002) for toluene, and -0.035 (+/- 0.003) for ethylbenzene. The small values of delta log Koc demonstrates that deuterated compounds are excellent tracers for the hydrologic behavior of ground water contaminants.

Coal test drilling for the DE-NA-Zin Bisti Area, San Juan County, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wilson, R.W.; Jentgen, R.W.

1980-01-01

From October 1978 to June 1979, the US Geological Survey (USGS) drilled 51 test holes, and cored 9 holes, in the vicinity of the Bisti Trading Post in the southwestern part of the San Juan Basin, San Juan County, New Mexico. The drilling was done in response to expressions of interest received by the Bureau of Land Management concerning coal leasing and, in some places, badlands preservation. The object of the drilling was to determine the depth, thickness, extent, and quality of the coal in the Upper Cretaceous Fruitland Formation in northwest New Mexico. The holes were geophysically logged immediatelymore » after drilling. Resistivity spontaneous-potential, and natural gamma logs were run in all of the holes. A high-resolution density log was also run in all holes drilled before January 13, when a logging unit from the USGS in Albuquerque was available. After January 13, the holes were logged by a USGS unit from Casper, Wyoming that lacked density logging capabilities. At nine locations a second hole was drilled, about 20 ft from the first hole, down to selected coal-bearing intervals and the coal beds were cored. A detailed description of each of the cores is given on the page(s) following the logs for each hole. From these coal cores, 32 intervals were selected and submitted to the Department of Energy in Pittsburgh, Pennsylvania, for analysis.« less

Investigative clinical study on prostate cancer part VIII: prolactin hormone and the pituitary-testicular-prostate axis at the time of initial diagnosis and subsequent cluster selection of the patient population after radical prostatectomy.

PubMed

Porcaro, Antonio B; Ghimenton, Claudio; Petrozziello, Aldo; Migliorini, Filippo; Romano, Mario; Sava, Teodoro; Caruso, Beatrice; Cocco, Claudio; Antoniolli, Stefano Zecchinini; Lacola, Vincenzo; Rubilotta, Emanuele; Monaco, Carmelo; Comunale, Luigi

2012-04-01

To evaluate the prolactin hormone (PRL) physiopathology along the pituitary testicular prostate axis at the time of initial diagnosis of prostate cancer and the subsequent cluster selection of the patient population after radical prostatectomy in relation to clinical and pathological variables. Ninety-two operated prostate cancer patients were retrospectively reviewed. No patient had previously received hormonal treatment. The investigated variables included PRL, follicle stimulating hormone (FSH), luteinizing hormone (LH), total testosterone (TT), free testosterone (FT), total prostate specific antigen (PSA), percentage of positive cores at transrectal ultrasound scan biopsy (TRUSB) (P+), biopsy Gleason score (bGS), pathology Gleason score (pGS), estimated tumor volume in relation to percentage of prostate volume (V+), overall prostate weight (Wi) and age. Empirical PRL correlations and multiple linear predictions were investigated along the pituitary testis prostate axis in the different groups of the prostate cancer population and clustered according to pT (2a/b, 3a, 3b/4) status. The patient population was classified according to the log(10) PRL/V+ ratio and clustered as follows: group A (log(10) PRL/V+ ≤1.5), B (1.5< log(10)PRL/V+ ≤2.0) and C (log(10) PRL/V+ >2.0). Simple linear regression analysis of V+ predicting PRL was computed for assessing the clustered model and analysis of variance was performed for assessing significant differences between the groups. PRL was independently predicted by FSH (p=0.01), LH (p=0.008) and P+ (p=0.06) in low-stage prostate cancer (pT2a/b). Interestingly, PRL was independently predicted by LH (p=0.03) and FSH, TT, FT, PSA, bGS, pGS, V+, Wi and age (all at p=0.01) in advanced stage-disease (pT3b/4). V+ was also significantly correlated (r=0.47) and predicted by P+ (p<0.0001) in the prostate cancer population. PRL was significantly correlated and predicted by V+ when the patient population was clustered according to the log(10)PRL/V+ ratio in group A (p=0.008), B (p<0.0001) and C (p<0.0001). Moreover, the three groups had significantly different mean values of PRL (p<0.0001), PSA (p=0.007), P+ (p=0.0001), V+ (p<0.0001), Wi (p=0.03), bGS (p=0.008), pGS (p=0.003); also, groups A, B and C had significant different pGS (p=0.03), pT (p=0.0008) and pR (p=0.01) frequency distributions. At diagnosis, in an operated prostate cancer population, PRL was significantly correlated and independently predicted along the pituitary testis prostate axis in high-stage disease; V+ was also significantly correlated and predicted by P+. Because of the high correlation and prediction of PRL by both V+ and P+, the prostate cancer population at diagnosis was clustered according to the log(10)PRL/V+ ratio into groups A, B and C that, in theory, might be models with prognostic potential and clinical applications in the prostate cancer population. However, confirmatory studies are needed.

Intensive hardwood log bucker training using HW Buck dramatically improves value recovery

Treesearch

James B. Pickens; Aaron Everett; Scott Noble; John E. Baumgras; Philip A. Araman; Conrad Waniger; Al Steele

2006-01-01

It has long been recognized that inappropriate placement of crosscuts when manufacturing hardwood logs from harvested stems (log bucking) reduces the value of logs produced. Recent studies have estimated losses in the range from 28% to 38% in the lake states region. It has not, however, been clear how to correct the problem. Efforts to improve value recovery have...

An equation for the prediction of human skin permeability of neutral molecules, ions and ionic species.

PubMed

Zhang, Keda; Abraham, Michael H; Liu, Xiangli

2017-04-15

Experimental values of permeability coefficients, as log K p , of chemical compounds across human skin were collected by carefully screening the literature, and adjusted to 37°C for the effect of temperature. The values of log K p for partially ionized acids and bases were separated into those for their neutral and ionic species, forming a total data set of 247 compounds and species (including 35 ionic species). The obtained log K p values have been regressed against Abraham solute descriptors to yield a correlation equation with R 2 =0.866 and SD=0.432 log units. The equation can provide valid predictions for log K p of neutral molecules, ions and ionic species, with predictive R 2 =0.858 and predictive SD=0.445 log units calculated by the leave-one-out statistics. The predicted log K p values for Na + and Et 4 N + are in good agreement with the observed values. We calculated the values of log K p of ketoprofen as a function of the pH of the donor solution, and found that log K p markedly varies only when ketoprofen is largely ionized. This explains why models that neglect ionization of permeants still yield reasonable statistical results. The effect of skin thickness on log K p was investigated by inclusion of two indicator variables, one for intermediate thickness skin and one for full thickness skin, into the above equation. The newly obtained equations were found to be statistically very close to the above equation. Therefore, the thickness of human skin used makes little difference to the experimental values of log K p . Copyright © 2017 Elsevier B.V. All rights reserved.

An attempt at predicting blood β-hydroxybutyrate from Fourier-transform mid-infrared spectra of milk using multivariate mixed models in Polish dairy cattle.

PubMed

Belay, T K; Dagnachew, B S; Kowalski, Z M; Ådnøy, T

2017-08-01

Fourier transform mid-infrared (FT-MIR) spectra of milk are commonly used for phenotyping of traits of interest through links developed between the traits and milk FT-MIR spectra. Predicted traits are then used in genetic analysis for ultimate phenotypic prediction using a single-trait mixed model that account for cows' circumstances at a given test day. Here, this approach is referred to as indirect prediction (IP). Alternatively, FT-MIR spectral variable can be kept multivariate in the form of factor scores in REML and BLUP analyses. These BLUP predictions, including phenotype (predicted factor scores), were converted to single-trait through calibration outputs; this method is referred to as direct prediction (DP). The main aim of this study was to verify whether mixed modeling of milk spectra in the form of factors scores (DP) gives better prediction of blood β-hydroxybutyrate (BHB) than the univariate approach (IP). Models to predict blood BHB from milk spectra were also developed. Two data sets that contained milk FT-MIR spectra and other information on Polish dairy cattle were used in this study. Data set 1 (n = 826) also contained BHB measured in blood samples, whereas data set 2 (n = 158,028) did not contain measured blood values. Part of data set 1 was used to calibrate a prediction model (n = 496) and the remaining part of data set 1 (n = 330) was used to validate the calibration models, as well as to evaluate the DP and IP approaches. Dimensions of FT-MIR spectra in data set 2 were reduced either into 5 or 10 factor scores (DP) or into a single trait (IP) with calibration outputs. The REML estimates for these factor scores were found using WOMBAT. The BLUP values and predicted BHB for observations in the validation set were computed using the REML estimates. Blood BHB predicted from milk FT-MIR spectra by both approaches were regressed on reference blood BHB that had not been used in the model development. Coefficients of determination in cross-validation for untransformed blood BHB were from 0.21 to 0.32, whereas that for the log-transformed BHB were from 0.31 to 0.38. The corresponding estimates in validation were from 0.29 to 0.37 and 0.21 to 0.43, respectively, for untransformed and logarithmic BHB. Contrary to expectation, slightly better predictions of BHB were found when univariate variance structure was used (IP) than when multivariate covariance structures were used (DP). Conclusive remarks on the importance of keeping spectral data in multivariate form for prediction of phenotypes may be found in data sets where the trait of interest has strong relationships with spectral variables. The Authors. Published by the Federation of Animal Science Societies and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

Effect of Selenium Supplementation on Recurrent Hyperthyroidism Caused by Graves' Disease: A Prospective Pilot Study.

PubMed

Wang, L; Wang, B; Chen, S R; Hou, X; Wang, X F; Zhao, S H; Song, J Q; Wang, Y G

2016-09-01

The effect of selenium supplementation on recurrent hyperthyroidism caused by Graves' disease is unclear. Our study aimed to assess the efficacy of selenium supplementation therapy on recurrent Graves' disease. Forty-one patients with recurrent Graves' disease were enrolled in this study. All patients received the routine treatment using methimazole (MMI), while patients allocated to the selenium group received additional selenium therapy for 6 months. The influence of selenium supplementation on the concentrations of thyroid stimulating hormone (TSH), anti-TSH-receptor antibodies (TRAb), free thyroxine (FT4), and free triiodothyronine (FT3) were assessed. The remission rate was also compared between 2 groups. There was no obvious difference in the demographic data and the levels of serum FT4, FT3, TSH, and TRAb between the 2 groups at baseline. Both FT4 and FT3 decreased more at 2 months in the selenium group than the controls, while the TSH level increased more in patients receiving selenium supplementation (p<0.05). The TRAb level was significantly lower in patients receiving selenium supplementation (2.4 IU/l vs. 5.6 IU/l, p=0.04). The percentages of patients with normal TRAb level at 6 months was also significantly higher in the selenium group (19.0 vs. 0%, p=0.016). Kaplan-Meier survival curve showed patients receiving selenium supplementation had a significantly higher rate of remission than controls (Log-rank test p=0.008). In conclusion, selenium supplementation can enhance the effect of antithyroid drugs in patients with recurrent Graves' disease. Randomized trials with large number of participants are needed to validate the finding above. © Georg Thieme Verlag KG Stuttgart · New York.

Free triiodothyronine levels and short-term prognosis in chronic heart failure patients with type 2 diabetes.

PubMed

Chen, Pingan; Li, Shaonan; Lei, Xiaoming; Liu, Zhen; Wu, Daihong; Luo, Yi; Xu, Dingli

2015-08-01

In chronic heart failure (CHF) patients with type 2 diabetes mellitus (T2DM), the role of thyroid hormone (TH) in predicting CHF severity and prognosis is unclear. The authors therefore investigated the role of TH in predicting CHF severity and prognosis in these specific patients. A total of 224 CHF patients (114 with T2DM) over a mean follow-up time of 6.56 ± 0.18 months were studied. TH, N-terminal pro-B-type natriuretic peptide (NT-proBNP) and other parameters were measured. Free triiodothyronine (FT3) levels were lower in the T2DM group compared with the nondiabetes group (P = 0.026) and higher in the New York Heart Association (NYHA) I group than in the NYHA III and IV groups (both P < 0.05). Compared with the low NT-proBNP group, the high NT-proBNP group had lower FT3 levels (P < 0.01). NT-proBNP correlated with NYHA classes (r = 0.541, P < 0.001), and inversely correlated with left ventricular ejection fraction (r = -0.431, P < 0.001) and FT3 levels (r = -0.335, P < 0.001). In multiple linear regression analysis, NT-proBNP was significantly correlated with NYHA classes (P < 0.001), left ventricular ejection fraction (P < 0.001) and FT3 (P = 0.004). Kaplan-Meier curves showed that the low FT3 group had an increased rate of short-term adverse outcomes of CHF (log rank, χ = 9.794, P = 0.002). FT3 levels are associated with the severity of CHF and seem to reflect short-term outcomes in CHF patients with T2DM.

Petroleum source potential of the Lower Cretaceous mudstone succession of the NPRA and Colville Delta area, North Slope Alaska, based on sonic and resistivity logs

USGS Publications Warehouse

Keller, Margaret A.; Bird, Kenneth J.

2003-01-01

Resource assessment of the North Slope of Alaska by the U. S. Geological Survey includes evaluation of the petroleum source potential of Mesozoic and Cenozoic rocks using the delta log R technique (Passey and others, 1990). Porosity and resistivity logs are used in combination with thermal maturity data to produce a continuous profile of total organic carbon content in weight % (TOC). From the pattern and amount of TOC in the profile produced, the depositional setting and thus the petroleum source-rock potential (kerogen type) of the organic matter can be inferred and compared to interpretations from other data such as Rock-Eval pyrolysis. TOC profiles determined by this technique for the contiguous interval of pebble shale unit, Hue Shale (including the Gamma Ray Zone or GRZ), and lower part of the Torok Formation indicate important potential for petroleum generation in the Tunalik 1, Inigok 1, N. Inigok 1, Kuyanak 1, Texaco Colville Delta 1, Nechelik 1, and Bergschrund 1 wells of the western North Slope region. TOC profiles suggest that this interval contains both type II and III kerogens – consistent with proposed depositional models -- and is predominantly greater than 2 wt. % TOC (cut-off used for effective source potential). Average TOC for the total effective section of the pebble shale unit + Hue Shale ranges from 2.6 to 4.1 wt % TOC (values predominantly 2-8% TOC) over 192-352 ft. Source potential for the lower Torok Formation, which also has interbedded sandstone and lean mudstone, is good to negligible in these 7 wells.

The Spontaneous Ray Log: A New Aid for Constructing Pseudo-Synthetic Seismograms

NASA Astrophysics Data System (ADS)

Quadir, Adnan; Lewis, Charles; Rau, Ruey-Juin

2018-02-01

Conventional synthetic seismograms for hydrocarbon exploration combine the sonic and density logs, whereas pseudo-synthetic seismograms are constructed with a density log plus a resistivity, neutron, gamma ray, or rarely a spontaneous potential log. Herein, we introduce a new technique for constructing a pseudo-synthetic seismogram by combining the gamma ray (GR) and self-potential (SP) logs to produce the spontaneous ray (SR) log. Three wells, each of which consisted of more than 1000 m of carbonates, sandstones, and shales, were investigated; each well was divided into 12 Groups based on formation tops, and the Pearson product-moment correlation coefficient (PCC) was calculated for each "Group" from each of the GR, SP, and SR logs. The highest PCC-valued log curves for each Group were then combined to produce a single log whose values were cross-plotted against the reference well's sonic ITT values to determine a linear transform for producing a pseudo-sonic (PS) log and, ultimately, a pseudo-synthetic seismogram. The range for the Nash-Sutcliffe efficiency (NSE) acceptable value for the pseudo-sonic logs of three wells was 78-83%. This technique was tested on three wells, one of which was used as a blind test well, with satisfactory results. The PCC value between the composite PS (SR) log with low-density correction and the conventional sonic (CS) log was 86%. Because of the common occurrence of spontaneous potential and gamma ray logs in many of the hydrocarbon basins of the world, this inexpensive and straightforward technique could hold significant promise in areas that are in need of alternate ways to create pseudo-synthetic seismograms for seismic reflection interpretation.

Image analysis for the automated estimation of clonal growth and its application to the growth of smooth muscle cells.

PubMed

Gavino, V C; Milo, G E; Cornwell, D G

1982-03-01

Image analysis was used for the automated measurement of colony frequency (f) and colony diameter (d) in cultures of smooth muscle cells, Initial studies with the inverted microscope showed that number of cells (N) in a colony varied directly with d: log N = 1.98 log d - 3.469 Image analysis generated the complement of a cumulative distribution for f as a function of d. The number of cells in each segment of the distribution function was calculated by multiplying f and the average N for the segment. These data were displayed as a cumulative distribution function. The total number of colonies (fT) and the total number of cells (NT) were used to calculate the average colony size (NA). Population doublings (PD) were then expressed as log2 NA. Image analysis confirmed previous studies in which colonies were sized and counted with an inverted microscope. Thus, image analysis is a rapid and automated technique for the measurement of clonal growth.

Facing Stormwater Management Challenges at a Southeastern Army Installation: US Army Garrison Fort Gordon

DTIC Science & Technology

2012-05-24

Medical Center • Host to Army, Navy, Air Force, Marines and multi- national forces • Supporting 17,950 military and 6,710 civilians 4 Fort Gordon...comply with the NPne:s ( National Pol utant Discharge Elimination System) Phase II stormwater oermit and reduce pollutants fourld in stonnwatar...Lane Avenue: • Approximately 50 ft drop • Stormwater management (constructed riffle ) • Streambank stabilization (geolift, log vane) 19

Volume and weight characteristics of a typical Douglas-fir/ western larch stand, Coram Experimental Forest, Montana

Treesearch

Robert E. Benson; Joyce A. Schlieter

1980-01-01

An over-mature Douglas-fir/western larch stand on the Coram Experimental Forest in Montana averaged about 7,300 ft3/acre (511 rn3/ha) of wood over 3 inches (7.62 cm) in diameter, and an additional 57 tons/acre (128/ha) of fine material, before harvest. After logging, using three different cutting methods and four different levels of utilization, wood residues ranged...

Methodology for locating defects within hardwood logs and determining their impact on lumber-value yield

Treesearch

Thomas Harless; Francis G. Wagner; Phillip Steele; Fred Taylor; Vikram Yadama; Charles W. McMillin

1991-01-01

A precise research methodology is described by which internal log-defect locations may help select hardwood log ortentation and sawing procedure to improve lumber value. Procedures for data collection, data handling, simulated sawing, and data analysis are described. A single test log verified the methodology. Results from this log showed significant differences in...

Lithostratigraphy, geophysics, biostratigraphy, and strontium-isotope stratigraphy of the surficial aquifer system of eastern Collier County and northern Monroe County, Florida

USGS Publications Warehouse

Weedman, S.D.; Paillet, Frederick L.; Edwards, L.E.; Simmons, K.R.; Scott, T.M.; Wardlaw, B.R.; Reese, R.S.; Blair, J.L.

1999-01-01

In 1997, ten cores were drilled in eastern Collier County and northern Monroe County, within the limits of the Big Cypress National Preserve. These cores represent a continuation of the study of seven cores in western Collier County begun in 1996 and reported in Weedman and others (1997) and Edwards and others (1998). This joint U.S. Geological Survey and Florida Geological Survey project is designed to acquire subsurface geologic and hydrologic data in southwest Florida to extend current ground-water models, thereby expanding the utility of these models for land and water management. In this report we describe the lithostratigraphy, geophysical logging, sedimentological analysis, dinocyst biostratigraphy, and strontium-isotope stratigraphy of these ten cores. The three geophysical logs (natural gamma-ray, induction conductivity, and neutron porosity) assumed to be related to formation lithology and water quality show that a number of clay-rich zones are present in all of the boreholes, and that pore-water conductivity increases with depth. The clay-rich zones are confirmed by visual examination of core material and sedimentological analysis. The relative transmissivity calculated at 10-foot-thick intervals shows that in six of the boreholes, high values are associated with the shallow aquifer in the 0-40 ft interval. Two of the boreholes (the most northerly and the most easterly) showed relatively higher values of transmissivity in permeable zones at or somewhat below 100 ft in depth. Core geology and logs indicate that the deeper aquifers are not more permeable than similar deeper zones in the other boreholes, but rather that the shallow aquifer appears to be less permeable in these two coreholes. The Arcadia (?) Formation was only penetrated in the deepest core where it is late Miocene in age. The Peace River Formation was penetrated in all but the two westernmost cores. It yields a late Miocene age, based on both dinocysts and strontium-isotope stratigraphy. The top is an irregular surface. Age and stratigraphic relations suggest that the upper part of the Peace River and lower part of the unnamed formation are at least partially equivalent laterally. The unnamed formation was recovered in every core. It is thinnest in the northernmost core and thickest to the west. Ages calculated from strontium isotopes range from 6.9 to 4.6 million years ago (late Miocene to early Pliocene). The top of the unnamed formation is deepest to the north and it becomes shallower to the southwest. The Tamiami Formation also was recovered in every core and consistently yields early Pliocene ages; it yields late Pliocene ages near the top in two cores. The age and lateral relations strongly suggest that the lower part of the Tamiami Formation and the upper part of the unnamed formation are lateral facies of each other. The Fort Thompson (?) Formation, Miami Limestone, and undifferentiated siliciclastic sediments and limestone at the very top of the cores were not dated.

FT-IR, FT-Raman, and DFT computational studies of melaminium nitrate molecular-ionic crystal

NASA Astrophysics Data System (ADS)

Tanak, Hasan; Marchewka, Mariusz K.

2013-02-01

The experimental and theoretical vibrational spectra of melaminium nitrate were studied. The Raman and infrared (FT-IR) spectra of the melaminium nitrate and its deuterated analogue were recorded in the solid phase. Molecular geometry and vibrational frequency values of melaminium nitrate in the electronic ground state were calculated using the density functional method (B3LYP) with the 6-31++G(d,p) basis set. The calculated results show that the optimized geometry can well reproduce the crystal structure, and the theoretical vibrational frequency values show good agreement with experimental values. The NBO analysis reveals that the N-H···O and N-H···N intermolecular interactions significantly influence crystal packing in this molecule.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mathews, M.A.; Bowman, H.R.; Huang, L., H.

A low radioactivity calibration facility has been constructed at the Nevada Test Site (NTS). This facility has four calibration models of natural stone that are 3 ft in diameter and 6 ft long, with a 12 in. cored borehole in the center of each model and a lead-shielded run pipe below each model. These models have been analyzed by laboratory natural gamma ray spectroscopy (NGRS) and neutron activation analysis (NAA) for their K, U, and Th content. Also, 42 other elements were analyzed in the NAA. The /sup 222/Rn emanation data were collected. Calibrating the spectral gamma tool in thismore » low radioactivity calibration facility allows the spectral gamma log to accurately aid in the recognition and mapping of subsurface stratigraphic units and alteration features associated with unusual concentrations of these radioactive elements, such as clay-rich zones.« less

Characterizing the Weeks Island Salt Dome drilling of and seismic measurements from boreholes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sattler, A.R.; Harding, R.S.; Jacobson, R.D.

1996-10-01

A sinkhole 36 ft across, 30 ft deep was first observed in the alluvium over the Weeks Island Salt Dome (salt mine converted for oil storage by US Strategic Petroleum Reserve) May 1992. Four vertical, two slanted boreholes were drilled for diagnostics. Crosswell seismic data were generated; the velocity images suggest that the sinkhole collapse is complicated, not a simple vertical structure. The coring operation was moderately difficult; limited core was obtained through the alluvium, and the quality of the salt core from the first two vertical wells was poor. Core quality improved with better bit selection, mud, and drillingmore » method. The drilling fluid program provided fairly stable holes allowing open hole logs to be run. All holes were cemented successfully (although it took 3 attempts in one case).« less

FT-IR imaging for quantitative determination of liver fat content in non-alcoholic fatty liver.

PubMed

Kochan, K; Maslak, E; Chlopicki, S; Baranska, M

2015-08-07

In this work we apply FT-IR imaging of large areas of liver tissue cross-section samples (∼5 cm × 5 cm) for quantitative assessment of steatosis in murine model of Non-Alcoholic Fatty Liver (NAFLD). We quantified the area of liver tissue occupied by lipid droplets (LDs) by FT-IR imaging and Oil Red O (ORO) staining for comparison. Two alternative FT-IR based approaches are presented. The first, straightforward method, was based on average spectra from tissues and provided values of the fat content by using a PLS regression model and the reference method. The second one – the chemometric-based method – enabled us to determine the values of the fat content, independently of the reference method by means of k-means cluster (KMC) analysis. In summary, FT-IR images of large size liver sections may prove to be useful for quantifying liver steatosis without the need of tissue staining.

Sugar and acid content of Citrus prediction modeling using FT-IR fingerprinting in combination with multivariate statistical analysis.

PubMed

Song, Seung Yeob; Lee, Young Koung; Kim, In-Jung

2016-01-01

A high-throughput screening system for Citrus lines were established with higher sugar and acid contents using Fourier transform infrared (FT-IR) spectroscopy in combination with multivariate analysis. FT-IR spectra confirmed typical spectral differences between the frequency regions of 950-1100 cm(-1), 1300-1500 cm(-1), and 1500-1700 cm(-1). Principal component analysis (PCA) and subsequent partial least square-discriminant analysis (PLS-DA) were able to discriminate five Citrus lines into three separate clusters corresponding to their taxonomic relationships. The quantitative predictive modeling of sugar and acid contents from Citrus fruits was established using partial least square regression algorithms from FT-IR spectra. The regression coefficients (R(2)) between predicted values and estimated sugar and acid content values were 0.99. These results demonstrate that by using FT-IR spectra and applying quantitative prediction modeling to Citrus sugar and acid contents, excellent Citrus lines can be early detected with greater accuracy. Copyright © 2015 Elsevier Ltd. All rights reserved.

Detailed lithologic log of the Dow Chemical #1 B.L. Garrigan Drill Hole, Mississippi County, Arkansas

USGS Publications Warehouse

Collins, Donley S.; Skipp, Gary L.

1995-01-01

The geology and tectonic setting of the New Madrid region in southeastern Missouri has received considerable attention because of the area's high seismic activity. The largest recorded earthquakes in this area occurred in the winter of 1811-1812. These earthquakes has estimated magnitudes as large as 8.0 on the Richter scale (Johnsonton and Kanter, 1990) and affected an area of about 1 million square miles (Fuller, 1912). Today, an area of continuously high seismic activity defines the New Madrid seismic zone, which extends from northeastern Arkansas into southeastern Missouri and northwestern Tennessee. Seismicity is locally concentrated along two subsurface archers--the Blytheville and Pascola (Hildenbrand and others, 1977; Crone and others, 1985; Hildenbrand, 1985; McKeown, 1988). The Padcola arch is not pertinent to this study and, therefore will not be discusses further. The Blytheville arch is located in and is subparallel to the axis of the northeast-southwest-trending Reelfoot structural basin, which formed during early Paleozoic rifting (Ervin and McGinnis, 1975; fig. 1). The Reelfoot basin is filled with Cambrian and Ordovician sedimentary rocks (Grohskopf, 1955; Howe, 1984; Houseknevht, 1989; Collins and others, 1992) that are uncomfortably overlain by Cretacaous and Tertiary sedimentary rocks and underlain by crystalline rocks of the eastern granite-rhyolite province (see Bickford and others, 1986). The presence of some Late Proterozoic sedimentary rocks in the Reelfoot basin currently cannot be ruled out. The Dow Chemical #1 B.L. Garrigan drill hole (hereafter, Garrigan) penetrated Paleozoic rocks on the Blytheville arch. The Garrigan is locted in the Reelfoot basin in the NW1/4, NW1/4 sec. 28, T. 15 N., R. 10 E., Mississippi County, Arkansas (fig. 1) and was completed to a total depth of 12,038 ft from a ground elevation of 239 ft on April 11, 1982 (Swolfs, 1991). The Garrigan is the only reported drill hole that penetrates the subsurface Blytheville arch and is an important source of core from the Reelfoot basin (Collins and others, 1992). Therefore, this drill hole is important for understanding structure and Paleozoic stratigraphy in a basin where stratigraphic and structural data are sparse. Rocks in the Garrigan were originally logged and described by J.R. Howe (personal communication to D.S. Collins, 1990) and published as a composite stratigraphic section along with the rock description for the Dow Chemical #1 Wilson drill hole (Howe, 1984). F.A. McKeown later relogged the rocks in the Garrigan and presented a generalized log in McKeown and others (1990). Swolfs (1991) presented another version of the Garrigan drill-hole geologic section (fig. 2). Aided by new biostratigraphic information, Taylor and others (1991) corrected major errors in the characterization and correlation of rocks in the Garrigan (fig. 2). Collins (1991) described the insoluble residues from the cuttings of the Garrigan, but could not correlate them with the insoluble resides from rocks of the carbonate platform west of the basin. However Taylor and others (1991), Collins and others (1992), and Collins and Bohm (1993) did correlate fossils from the Garrigan to other drill holes in the Reelfoot basin and adjacent areas. Using these correlated data, Collins and Bohm (1993) provided information on the structural relief across a part of the Reelfoot basin. Collins and others (1992) also interpreted the depositional setting for the Paleozoic rocks of the Garrigan. This report presents a detailed lithologic log of the Paleozoic rocks penetrated by the Garrigan that differs from the lithologic logs of previous workers (Howe, 1984; McKeown and others, 1990; see also Dart, 1992, p. 18-19). The lithologic descriptions of the Garrigan are derived from observations of well cuttings and core. Cored intervals used were 11,426-11,402 ft, 10,229-10,200 ft, and 8,002-7,979 ft. These intervals were the only intervals cored during the Garrigan drill project. Detailed analyses of the core will be described in a subsequent report.

Feature tracking CMR reveals abnormal strain in preclinical arrhythmogenic right ventricular dysplasia/ cardiomyopathy: a multisoftware feasibility and clinical implementation study.

PubMed

Bourfiss, Mimount; Vigneault, Davis M; Aliyari Ghasebeh, Mounes; Murray, Brittney; James, Cynthia A; Tichnell, Crystal; Mohamed Hoesein, Firdaus A; Zimmerman, Stefan L; Kamel, Ihab R; Calkins, Hugh; Tandri, Harikrishna; Velthuis, Birgitta K; Bluemke, David A; Te Riele, Anneline S J M

2017-09-01

Regional right ventricular (RV) dysfunction is the hallmark of Arrhythmogenic Right Ventricular Dysplasia/Cardiomyopathy (ARVD/C), but is currently only qualitatively evaluated in the clinical setting. Feature Tracking Cardiovascular Magnetic Resonance (FT-CMR) is a novel quantitative method that uses cine CMR to calculate strain values. However, most prior FT-CMR studies in ARVD/C have focused on global RV strain using different software methods, complicating implementation of FT-CMR in clinical practice. We aimed to assess the clinical value of global and regional strain using FT-CMR in ARVD/C and to determine differences between commercially available FT-CMR software packages. We analyzed cine CMR images of 110 subjects (39 overt ARVD/C [mutation+/phenotype+], 40 preclinical ARVD/C [mutation+/phenotype-] and 31 control) for global and regional (subtricuspid, anterior, apical) RV strain in the horizontal longitudinal axis using four FT-CMR software methods (Multimodality Tissue Tracking, TomTec, Medis and Circle Cardiovascular Imaging). Intersoftware agreement was assessed using Bland Altman plots. For global strain, all methods showed reduced strain in overt ARVD/C patients compared to control subjects (p < 0.041), whereas none distinguished preclinical from control subjects (p > 0.275). For regional strain, overt ARVD/C patients showed reduced strain compared to control subjects in all segments which reached statistical significance in the subtricuspid region for all software methods (p < 0.037), in the anterior wall for two methods (p < 0.005) and in the apex for one method (p = 0.012). Preclinical subjects showed abnormal subtricuspid strain compared to control subjects using one of the software methods (p = 0.009). Agreement between software methods for absolute strain values was low (Intraclass Correlation Coefficient = 0.373). Despite large intersoftware variability of FT-CMR derived strain values, all four software methods distinguished overt ARVD/C patients from control subjects by both global and subtricuspid strain values. In the subtricuspid region, one software package distinguished preclinical from control subjects, suggesting the potential to identify early ARVD/C prior to overt disease expression.

Ground-water resources of southern Tangipahoa Parish and adjacent areas, Louisiana

USGS Publications Warehouse

Rapp, T.R.

1994-01-01

Groundwater resources in southern Tangipahoa Parish and adjacent areas were studied to determine their potential for development as an alternative to the Mississippi River as a water-supply source for Jefferson Parish. Eight major aquifers consisting of thick sand units that underlie the study area are, in descending order: (1) shallow, (2) upper Ponchatoula, (3) lower Ponchatoula, (4) Abita, (5) Covington, (6) Tchefuncta, (7) Hammond, and (8) Amite. A fault zone, referred to as the Baton Rouge fault, crosses southern Tangipahoa Parish. Analyses of geophysical logs indicated that the deep aquifers south of the fault zone had been displaced from 350 to 400 feet, and that the deeper aquifers were not in hydraulic connection with the flow system north of the fault. The groundwater resources of southeastern Louisiana are immense and the quality of groundwater in Tangipahoa Parish is suitable for most uses. The quality of water in these aquifers generally meets the U.S. Environmental Protection Agency's standards for public supply. The hydrologic system underlying Tangipahoa Parish and adjacent areas in 1990 supplied about 19 Mgal/d of water that was suitable for public supply. However, substantial increases in pumping from the aquifer system would result in renewed water-level declines throughout the hydrologic system until a new equilibrium is established. A test we11 in southern Tangipahoa Parish, penetrated all eight aquifers. Total thickness of freshwater sand beds penetrated by the 3003-ft test hole was more than 1900 ft. Resistivity values from an electric log of the test typically averaged 200 ohm-meters, which indicates that the water has low dissolved-solids and chloride concentrations. An analysis of the Abita aquifer at Ruddock in St. John the Baptist Parish, for two of three hypothetical well fields, indicated that for a hypothetical we11 field with a pumping rate of 112 Mgal/d, the freshwater/saltwater interface could arrive at the outer perimeter we11 in 10 to 14 years. The 1990 location of the interface in the Abita aquifer is 1.9 mi from the southernmost part of the potential location of the 112 Mgal/d well field.

The structure of Al-23 and astrophysical consequences

NASA Astrophysics Data System (ADS)

Zhai, Yongjun

Motivated by existing nuclear astrophysics problems, the b-decay of the proton rich nucleus 23 Al was studied for the first time with pure samples which were obtained by using the 1 H( 24 Mg, 23 Al)2n reaction and the MARS recoil separator at Texas A&M University. b and b-g coincidence measurements were made with a fast tape-transport system, scintillator, BGO and HPGe g detectors. The experiment allowed us to measure absolute b branching ratios and to determine log ft values for transitions to final states in 23 Mg, including the isobaric analog state (IAS), and, therefore, to determine unambiguously the spin and parity of the 23 Al ground state to be J p = 5/2 + . This work excludes the large increases in the radiative proton capture cross section for the reaction 22 Mg(p,g) 23 Al at astrophysical energies, which were implied by claims that the spin and parity of the 23 Al ground state were J p = 1/2 + . More precise half life and mass determinations of 23 Al were obtained from the experimental data. The log ft for the Fermi transition to its isobaric analog state in 23 Mg was also determined for the first time. This IAS and a state 16 keV below it were observed, well separated in the same experiment for the first time. The b- decay scheme of the proton rich nucleus 23 Al was established. We can now solve a number of inconsistencies in the literature, exclude strong isospin mixing claimed before, and obtain a new determination of the resonance strength. The IAS and the state 16 keV below it are resonances in the 22 Na(p,g) 23 Mg reaction at energies that are important in novae. This second state turns out to be the resonance that gives the most important contribution in the depletion of 22Na from novae. Both of the reactions of 22 Mg(p,g) 23 Al and 22 Na(p,g) 23 Mg have been suggested as possible candidates for diverting some of the flux in oxygen-neon novae explosions from the A=22 into the A=23 mass chain.

Adjusting Quality index Log Values to Represent Local and Regional Commercial Sawlog Product Values

Treesearch

Orris D. McCauley; Joseph J. Mendel; Joseph J. Mendel

1969-01-01

The primary purpose of this paper is not only to report the results of a comparative analysis as to how well the Q.I. method predicts log product values when compared to commercial sawmill log output values, but also to develop a methodology which will facilitate the comparison and provide the adjustments needed by the sawmill operator.

SALTON SEA SCIENTIFIC DRILLING PROJECT: SCIENTIFIC PROGRAM.

USGS Publications Warehouse

Sass, J.H.; Elders, W.A.

1986-01-01

The Salton Sea Scientific Drilling Project, was spudded on 24 October 1985, and reached a total depth of 10,564 ft. (3. 2 km) on 17 March 1986. There followed a period of logging, a flow test, and downhole scientific measurements. The scientific goals were integrated smoothly with the engineering and economic objectives of the program and the ideal of 'science driving the drill' in continental scientific drilling projects was achieved in large measure. The principal scientific goals of the project were to study the physical and chemical processes involved in an active, magmatically driven hydrothermal system. To facilitate these studies, high priority was attached to four areas of sample and data collection, namely: (1) core and cuttings, (2) formation fluids, (3) geophysical logging, and (4) downhole physical measurements, particularly temperatures and pressures.

A one-year follow-up on the effects of raloxifene on thyroid function in postmenopausal women.

PubMed

Ceresini, Graziano; Morganti, Simonetta; Rebecchi, Isabella; Bertone, Luca; Ceda, Gian Paolo; Bacchi-Modena, Alberto; Sgarabotto, Mariapaola; Baldini, Monica; Ablondi, Fabrizio; Valenti, Giorgio; Braverman, Lewis E

2004-01-01

Estrogens increase serum thyroxine-binding globulin (TBG) and total thyroxine (TT4) concentrations. Serum free thyroxine (FT4) concentrations, however, remain normal. Raloxifene (RAL) is a selective estrogen receptor modulator used to treat postmenopausal osteoporosis. Data on the long-term effects of RAL on thyroid physiology are scanty. We evaluated the effects of RAL administration for 1 year on thyroid function in osteopenic, postmenopausal women. Fifty osteopenic, postmenopausal women were randomly assigned to receive either RAL (60 mg/day, n = 25) or placebo (PL, n = 25) for 1 year, in a double-blind study. Measurements of serum TBG, TT4, FT4, thyroid-stimulating hormone (TSH), thyroid hormone-binding ratio (THBR), FT4 index (FT4-I) and TT4/TBG ratio were carried out at baseline and after 4 and 12 months of therapy. Baseline values were similar in both treatment groups. Serum TBG concentrations were increased during RAL treatment from baseline values of 29.60 +/- 0.9 microg/mL to 31.45 +/- 1.33 and 32.34 +/- 1.37 microg/mL at 4 months and 1 year, respectively (P < 0.05, baseline v 1-year values) but were unchanged during PL treatment. A small, insignificant increase in TT4 and TSH concentrations occurred in the RAL group and no changes in the PL group. All other values were unchanged during either treatment. These results demonstrate that RAL significantly increased serum TBG levels, but the changes were small and not accompanied by changes in FT4-I, FT4, or TSH concentrations, suggesting that long-term RAL treatment is unlikely to clinically affect the thyroid status in euthyroid, postmenopausal women.

Opon gas renews interest in the hydrocarbon prolific middle Magdalena basin, Colombia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, D.M.; Elliott, R.; Latimer, G.

1996-08-01

A total of 45 fields have been discovered in the Middle Magdelena basin of Colombia since 1918. In August 1994, the Amoco-operated Opon-3 well tested significant hydrocarbons in the basin. The well flowed 45 MMCFGPD and 2000 BCPD from 1118 ft of perforations between 10,018 and 12,348 feet. A second well, Opon-4, tested 58 MMCFGPD from the same interval. Opon now appears to be a significant gas condensate field. A full assessment of commercial potential requires 3D seismic data, as well as further development drilling. Operational challenges include: drilling, coring, logging, cementing and testing in a world-record setting 23 ppgmore » hematite-weighted mud environment involving simultaneous perforation over a 2330 ft gross pay interval and management of high production rates at >8000 psi FwHP. The Opon structure is a surface anticline on the western edge of the Eastern Cordillera fold and thrust belt. Seismic definition of the trap, however, is complicated by multiple faults, steep dips, rugged topography and variable surface velocities. The main gas reservoirs are fluvial sandstones of the Eocene La Paz Formation sealed by the overlying upper Eocene Las Esmeraldas Formation shales. Individual producing sandstones range from 40 to 200 ft thick in a minimum gross gas column of 4200 ft. Average porosity is 6%. Tectonically induced fractures probably enhance reservoir performance.« less

Is it time to revisit the log-sort yard?

Treesearch

John Dramm; Gerry Jackson

2000-01-01

Log-sort yards provide better utilization and marketing with improved value recovery of currently available timber resources in North America. Log-sort yards provide many services in marketing wood and fiber by concentrating, merchandising, manufacturing, sorting, and adding value to logs. Such operations supply forest products firms with desired raw materials, which...

Sorption of ionic and nonionic organic solutes onto giant Miscanthus-derived biochar from methanol-water mixtures.

PubMed

Kim, Juhee; Hyun, Seunghun

2018-02-15

The sorption of naphthalene (NAP) and 1-naphthoic acid (1-NAPA) onto giant Miscanthus-derived biochar was investigated in methanol volume fractions (f c ) of 0-0.6 as a function of ionic composition (5mM CaCl 2 and 10mM KCl) and liquid pH (2 and 7). The sorption onto biochar was nonlinear with 0.42≤N≤0.95; thus, a concentration-specific sorption constant (K m ) was compared. The K m log linearly decreased with increasing f c , except for 1-NAPA from a CaCl 2 mixture at pH7. Isotherm data was fitted with a cosolvency sorption model through which the slope (ασ) of the inverse log linear K m -f c plot and empirical constant (α) were obtained. NAP sorption was well described by the cosolvency model with the α value being 0.41-0.53, indicating a methanol-biochar interaction favoring more sorption than the cosolvency based prediction. In particular, the slope (ασ) of 1-NAPA was lower than that of NAP, indicating less reduction of 1-NAPA sorption (i.e., lower α value) by methanol. In comparison with other sorbents, the α value was approximately intermediate between a humic substance and kaolinite clay. An analysis of FT-IR spectra suggested the transformation of O-containing functional groups by methanol, which will subsequently boost the π-π interaction between an organic solute and biochar. Moreover, Ca 2+ -induced sorption between anionic 1-NAPA and a negatively charged biochar surface was also fortified in the methanol mixture. The results revealed unexplored cosolvent effects on organic solute sorption onto biochar and identified the hydrophobic and hydrophilic sorption moieties of biochar as affected by the cosolvent. Copyright © 2017 Elsevier B.V. All rights reserved.

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

Linkage of the Soil and Water Assessment Tool and the Texas Water Availability Model to simulate the effects of brush management on monthly storage of Canyon Lake, south-central Texas, 1995-2010

USGS Publications Warehouse

Asquith, William H.; Bumgarner, Johnathan R.

2014-01-01

The mean monthly offset storages of Canyon Lake during the Drought Quartile were 110 acre-ft (20 percent); 448 acre-ft (40 percent); 754 acre-ft (60 percent); 1,080 acre-ft (80 percent); and 1,090 acre-ft (100 percent). A particular mean was interpreted as follows: the value of 754 acre-ft for the 60-percent brush-management scenario implies that, on average, this scenario indicates an additional 754 acre-ft per month of storage in Canyon Lake relative to the baseline during the Drought Quartile. All of the five scenarios resulted in an increase on average to water supply relative to the baseline scenario during the Drought Quartile through the SWAT-WAM linkage.

Martins Fork Lake Sedimentation Study. Hydraulic Model Investigation

DTIC Science & Technology

1988-09-01

30 per- cent of the 1.67 acre-ft/square mile, or 0.50 acre-ft/square mile was selected to represent the new expected sediment inflow rate (USAED...Cross Sec- tion Coordinates" (GEDA). The GEDA files were converted to HEC-6 format. Roughness 15. Manning’s n values were selected for each stem of...the network. The values selected are shown in Table 2. Table 2 * Manning’s n Values Network n Value Martins Fork main stem 0.040 Crane Creek 0.045 Board

Spectroscopic (FT-IR, FT-Raman, FT-NMR and UV-Vis) investigation on benzil dioxime using quantum computational methods

NASA Astrophysics Data System (ADS)

Bakkiyaraj, D.; Periandy, S.; Xavier, S.

2016-03-01

The spectral analysis of benzil dioxime is carried out using the FTIR, FT Raman, FT NMR and UV-Vis spectra of the compound with the help of quantum computations by density functional theories. The FT-IR (4000 - 400 cm-1) and FT-Raman (4000-100 cm-1) spectra are recorded in solid phase, the 1H and 13C NMR spectra in DMSO phase and the UV spectrum (200-400 nm) in ethanol phase. The different conformers of the compound and their minimum energies are studied by potential energy surface scan, using semi-empirical method PM6. The computed wavenumbers from different methods are scaled so as to agree with the experimental values and the scaling factors are reported. All the fundamental modes have been assigned based on the potential energy distribution (PED) values and the structure the molecule is analyzed interms of parameters like bond length, bond angle and dihedral angles predicted byB3LYP and CAM-B3LYP methods with cc-pVDZ basis sets. The values of dipole moment (μ), polarizability (α) and hyperpolarizability (β) of the molecule are reported, using which the non -linear optical property of the molecule is discussed. The HOMO-LUMO mappings are reported which reveals the different charge transfer possibilities within the molecule. The isotropic chemical shifts predicted for 1H and 13C atoms using gauge invariant atomic orbital (GIAO) theory show good agreement with experimental shifts and the same is discussed in comparison with atomic charges, predicted by Mullikan and APT charge analysis. NBO analysis is carried out to picture the probable electronic transitions in the molecule.

Low free triiodothyronine levels predict symptomatic intracranial hemorrhage and worse short-term outcome of thrombolysis in patients with acute ischemia stroke.

PubMed

Qiu, Mingjing; Fang, Min; Liu, Xueyuan

2017-11-01

The aim of the study was to determine whether thyroid hormones level on admission in patients with ischemic stroke, treated with intravenous recombinant tissue type plasminogen activator (rtPA), was associated with symptomatic intracranial hemorrhage (sICH) and worse outcomes at 3 months.Patients with acute ischemic stroke (AIS) receiving intravenous rtPA thrombolytic treatment on our stroke unit between January 2015 and June 2016 were included in this study. Serum-free triiodothyronine (fT3), free thyroxine (fT4), total triiodothyronine (tT3), total thyroxine (tT4), and thyroid-stimulating hormone (TSH) were detected on admission. The endpoints were sICH, and poor functional outcomes at 3 and 6 months.In all, 159 patients (106 males; mean age 65.36 ± 10.02 years) were included. FT3 was independently associated with sICH (odds ratio [OR] 0.204, 95% confidence interval [CI] 0.065-0.642) and poor outcomes at 3 months (OR 0.396, 95% CI 0.180-1.764). The cut-off values of fT3 for sICH was 3.54 pg/mL (sensitivity 83%; specificity 83%; area under the curve 0.88). FT3 values ≤3.54 pg/mL increased risk for sICH by 3.16-fold (95% CI 0.75-1.0) compared with fT3 values >3.54 pg/mL.Low fT3 levels at admission were independently associated with sICH and worse outcomes at 3 months in AIS patients receiving rtPA thrombolytic therapy.

Low free triiodothyronine levels predict symptomatic intracranial hemorrhage and worse short-term outcome of thrombolysis in patients with acute ischemia stroke

PubMed Central

Qiu, Mingjing; Fang, Min; Liu, Xueyuan

2017-01-01

Abstract The aim of the study was to determine whether thyroid hormones level on admission in patients with ischemic stroke, treated with intravenous recombinant tissue type plasminogen activator (rtPA), was associated with symptomatic intracranial hemorrhage (sICH) and worse outcomes at 3 months. Patients with acute ischemic stroke (AIS) receiving intravenous rtPA thrombolytic treatment on our stroke unit between January 2015 and June 2016 were included in this study. Serum-free triiodothyronine (fT3), free thyroxine (fT4), total triiodothyronine (tT3), total thyroxine (tT4), and thyroid-stimulating hormone (TSH) were detected on admission. The endpoints were sICH, and poor functional outcomes at 3 and 6 months. In all, 159 patients (106 males; mean age 65.36 ± 10.02 years) were included. FT3 was independently associated with sICH (odds ratio [OR] 0.204, 95% confidence interval [CI] 0.065–0.642) and poor outcomes at 3 months (OR 0.396, 95% CI 0.180–1.764). The cut-off values of fT3 for sICH was 3.54 pg/mL (sensitivity 83%; specificity 83%; area under the curve 0.88). FT3 values ≤3.54 pg/mL increased risk for sICH by 3.16-fold (95% CI 0.75–1.0) compared with fT3 values >3.54 pg/mL. Low fT3 levels at admission were independently associated with sICH and worse outcomes at 3 months in AIS patients receiving rtPA thrombolytic therapy. PMID:29137061

Recharge rates and aquifer hydraulic characteristics for selected drainage basins in middle and east Tennessee

USGS Publications Warehouse

Hoos, A.B.

1990-01-01

Quantitative information concerning aquifer hydrologic and hydraulic characteristics is needed to manage the development of ground-water resources. These characteristics are poorly defined for the bedrock aquifers in Middle and East Tennessee where demand for water is increasing. This report presents estimates of recharge rate, storage coefficient, diffusivity, and transmissivity for representative drainage basins in Middle and East Tennessee, as determined from analyses of stream-aquifer interactions. The drainage basins have been grouped according to the underlying major aquifer, then statistical descriptions applied to each group, in order to define area1 distribution of these characteristics. Aquifer recharge rates are estimated for representative low, average, and high flow years for 63 drainage basins using hydrograph analysis techniques. Net annual recharge during average flow years for all basins ranges from 4.1 to 16.8 in/yr (inches per year), with a mean value of 7.3 in. In general, recharge rates are highest for basins underlain by the Blue Ridge aquifer (mean value11.7 in/yr) and lowest for basins underlain by the Central Basin aquifer (mean value 5.6 in/yr). Mean recharge values for the Cumberland Plateau, Highland Rim, and Valley and Ridge aquifers are 6.5, 7.4, and 6.6 in/yr, respectively. Gravity drainage characterizes ground-water flow in most surficial bedrock aquifer in Tennessee. Accordingly, a gravity yield analysis, which compares concurrent water-level and streamflow hydrographs, was used to estimate aquifer storage coefficient for nine study basins. The basin estimates range from 0.002 to 0.140; however, most estimates are within a narrow range of values, from 0.01 to 0.025. Accordingly, storage coefficient is estimated to be 0.01 for all aquifers in Middle and East Tennessee, with the exception of the aquifer in the inner part of the Central Basin, for which storage coefficient is estimated to be 0.002. Estimates of aquifer hydraulic diffusivity are derived from estimates of the streamflow recession index and drainage density for 75 drainage basins; values range from 3,300 to 130,000 ft^2/d (feet squared per day). Basin-specific and site-specific estimates of transmissivity are computed from estimates of hydraulic diffusivity and specific-capacity test data, respectively. Basin-specific, or areal, estimates of transmissivity range from 22 to 1,300 ft^2/d, with a mean of 240 ft^2/d In general, areal transmissivity is highest for basins underlain by the Cumberland Plateau aquifer (mean value 480 ft^2/d) and lowest for basins underlain by the Central Basin aquifer (mean value 79 ft^2/d). Mean transmissivity values for the Highland Rim, Valley and Ridge, and Blue Ridge aquifer are 320,140, and 120 ft^2/d respectively. Site-specific estimates of transmissivity, computed from specific-capacity data from 118 test wells in Middle and East Tennessee range from 2 to 93,000 ft^2/d with a mean of 2,600 ft^2/d Mean transmissivity values for the Cumberland Plateau, Highland Rim, Central Basin, Valley and Ridge, and Blue Ridge aquifers are 2,800,1,200, 7,800, 390, and 65Oft Id, respectively.

Small-diameter log evaluation for value-added structural applications

Treesearch

Ronald Wolfe; Cassandra Moseley

2000-01-01

Three species of small-diameter logs from the Klamath/Siskiyou Mountains and the Cascade Range in southwest Oregon were tested for their potential for value-added structural applications. The logs were tested in bending and compression parallel to the grain. Strength and stiffness values were correlated to possible nondestructive evaluation grading parameters and...

Applications of QCL mid-IR imaging to the advancement of pathology

NASA Astrophysics Data System (ADS)

Sreedhar, Hari; Varma, Vishal K.; Bird, Benjamin; Guzman, Grace; Walsh, Michael J.

2017-03-01

Quantum Cascade Laser (QCL) spectroscopic imaging is a novel technique with many potential applications to histopathology. Like traditional Fourier Transform Infrared (FT-IR) imaging, QCL spectroscopic imaging derives biochemical data coupled to the spatial information of a tissue sample, and can be used to improve the diagnostic and prognostic value of assessment of a tissue biopsy. This technique also offers advantages over traditional FT-IR imaging, specifically the capacity for discrete frequency and real-time imaging. In this work we present applications of QCL spectroscopic imaging to tissue samples, including discrete frequency imaging, to compare with FT-IR and its potential value to pathology.

Effect of small changes in sawpattern on lumber value in pruned Douglas fir logs: Steps toward greater value from pruned logs.

Treesearch

Christine Todoroki; Eini Lowell

2006-01-01

The silvicultural practice of pruning juvenile stems is a value-adding operation due to the formation of knot-free wood after the pruned branch stubs have healed. However it is not until after the log has been processed that the added value is realized. The motivation for this paper stems from wanting to extract as much of that added value as possible while minimizing...

A performance test of the log and tree grades for eastern white pine

Treesearch

Robert L. Brisbin

1972-01-01

The results of testing the Forest Service standard tree grades and sawlog grades for eastern white pine on an independent sample of 75 trees and 299 logs in southwestern Maine. The total predicted value of the 75 trees was 3 percent higher than the actual value. The total predicted value of the 299 logs was 2 percent higher than the actual value. The differences...

Assessment of the hygienic performances of hamburger patty production processes.

PubMed

Gill, C O; Rahn, K; Sloan, K; McMullen, L M

1997-05-20

The hygienic conditions of the hamburger patties collected from three patty manufacturing plants and six retail outlets were examined. At each manufacturing plant a sample from newly formed, chilled patties and one from frozen patties were collected from each of 25 batches of patties selected at random. At three, two or one retail outlet, respectively, 25 samples from frozen, chilled or both frozen and chilled patties were collected at random. Each sample consisted of 30 g of meat obtained from five or six patties. Total aerobic, coliform and Escherichia coli counts per gram were enumerated for each sample. The mean log (x) and standard deviation (s) were calculated for the log10 values for each set of 25 counts, on the assumption that the distribution of counts approximated the log normal. A value for the log10 of the arithmetic mean (log A) was calculated for each set from the values of x and s. A chi2 statistic was calculated for each set as a test of the assumption of the log normal distribution. The chi2 statistic was calculable for 32 of the 39 sets. Four of the sets gave chi2 values indicative of gross deviation from log normality. On inspection of those sets, distributions obviously differing from the log normal were apparent in two. Log A values for total, coliform and E. coli counts for chilled patties from manufacturing plants ranged from 4.4 to 5.1, 1.7 to 2.3 and 0.9 to 1.5, respectively. Log A values for frozen patties from manufacturing plants were between < 0.1 and 0.5 log10 units less than the equivalent values for chilled patties. Log A values for total, coliform and E. coli counts for frozen patties on retail sale ranged from 3.8 to 8.5, < 0.5 to 3.6 and < 0 to 1.9, respectively. The equivalent ranges for chilled patties on retail sale were 4.8 to 8.5, 1.8 to 3.7 and 1.4 to 2.7, respectively. The findings indicate that the general hygienic condition of hamburgers patties could be improved by their being manufactured from only manufacturing beef of superior hygienic quality, and by the better management of chilled patties at retail outlets.

Depositional environments and sand body morphologies of the muddy sandstones at Kitty Field, Powder River Basin, Wyoming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larberg, G.M.B.

1980-01-01

Lower Cretaceous muddy sandstones form a stratigraphic trap at Kitty Field, Campbell County, Wyoming. Porosity and permeability are generally low, but the best reservoir develop maximum effective porosity of 17% and maximum permeability of 442 md. Reservoirs sandstones average less than 15 ft and rarely exceed 30 ft in thickness. Ultimate recovery from the field is estimated at 23 million bbl. Based on electric log character, 4 easily recognizable zones within the muddy interval at Kitty were numbered one through 4 in slabbed cores and petrographic analyses of selected core samples, suggest that sandstones in the second, third, and fourthmore » muddy zones were deposited as part of a sequence associated with the overall transgression of the lower Cretaceous sea. Fourth zone sandstones are fluvial in origin, and were deposited in lows on the unconformable surface of the underlying skull creek shale. 18 references.« less

Conformational analysis, X-ray crystallographic, FT-IR, FT-Raman, DFT, MEP and molecular docking studies on 1-(1-(3-methoxyphenyl) ethylidene) thiosemicarbazide

NASA Astrophysics Data System (ADS)

Saravanan, R. R.; Seshadri, S.; Gunasekaran, S.; Mendoza-Meroño, R.; Garcia-Granda, S.

2015-03-01

Conformational analysis, X-ray crystallographic, FT-IR, FT-Raman, DFT, MEP and molecular docking studies on 1-(1-(3-methoxyphenyl) ethylidene) thiosemicarbazide (MPET) are investigated. From conformational analysis the examination of the positions of a molecule taken and the energy changes is observed. The docking studies of the ligand MPET with target protein showed that this is a good molecule which docks well with target related to HMG-CoA. Hence MPET can be considered for developing into a potent anti-cholesterol drug. MEP assists in optimization of electrostatic interactions between the protein and the ligand. The MEP surface displays the molecular shape, size and electrostatic potential values. The optimized geometry of the compound was calculated from the DFT-B3LYP gradient calculations employing 6-31G (d, p) basis set and calculated vibrational frequencies are evaluated via comparison with experimental values.

Petrophysical Properties of Cody, Mowry, Shell Creek, and Thermopolis Shales, Bighorn Basin, Wyoming

NASA Astrophysics Data System (ADS)

Nelson, P. H.

2013-12-01

The petrophysical properties of four shale formations are documented from well-log responses in 23 wells in the Bighorn Basin in Wyoming. Depths of the examined shales range from 4,771 to 20,594 ft. The four formations are the Thermopolis Shale (T), the Shell Creek Shale (SC), the Mowry Shale (M), and the lower part of the Cody Shale (C), all of Cretaceous age. These four shales lie within a 4,000-ft, moderately overpressured, gas-rich vertical interval in which the sonic velocity of most rocks is less than that of an interpolated trendline representing a normal increase of velocity with depth. Sonic velocity, resistivity, neutron, caliper, and gamma-ray values were determined from well logs at discrete intervals in each of the four shales in 23 wells. Sonic velocity in all four shales increases with depth to a present-day depth of about 10,000 ft; below this depth, sonic velocity remains relatively unchanged. Velocity (V), resistivity (R), neutron porosity (N), and hole diameter (D) in the four shales vary such that: VM > VC > VSC > VT, RM > RC > RSC > RT, NT > NSC ≈ NC > NM, and DT > DC ≈ DSC > DM. These orderings can be partially understood on the basis of rock compositions. The Mowry Shale is highly siliceous and by inference comparatively low in clay content, resulting in high sonic velocity, high resistivity, low neutron porosity, and minimal borehole enlargement. The Thermopolis Shale, by contrast, is a black fissile shale with very little silt--its high clay content causes low velocity, low resistivity, high neutron response, and results in the greatest borehole enlargement. The properties of the Shell Creek and lower Cody Shales are intermediate to the Mowry and Thermopolis Shales. The sonic velocities of all four shales are less than that of an interpolated trendline that is tied to velocities in shales above and below the interval of moderate overpressure. The reduction in velocity varies among the four shales, such that the amount of offset (O) from the trendline is OT > OSC > OC > OM, that is, the velocity in the Mowry Shale is reduced the least and the velocity in the Thermopolis Shale is reduced the most. Velocity reductions are attributed to increases in pore pressure during burial, caused by the generation and retention of gas, with lithology playing a key role in the amount of reduction. Sonic velocity in the four shale units remains low to the present day, after uplift and erosion of as much as 6,500 ft in the deeper part of the basin and consequent possible reduction from maximum pore pressures reached when strata were more deeply buried. A model combining burial history, the decrease of effective stress with increasing pore pressure, and Bower's model for the dependence of sonic velocity on effective stress is proposed to explain the persistence of low velocity in shale units. Interruptions to compaction gradients associated with gas occurrences and overpressure are observed in correlative strata in other basins in Wyoming, so the general results for shales in the Bighorn Basin established in this paper should be applicable elsewhere.

Metabolic optimisation of the basketball free throw.

PubMed

Padulo, Johnny; Attene, Giuseppe; Migliaccio, Gian Mario; Cuzzolin, Francesco; Vando, Stefano; Ardigò, Luca Paolo

2015-01-01

The free throw (FT) is a fundamental basketball skill used frequently during a match. Most of actual play occurs at about 85% of maximum heart rate (HR). Metabolic intensity, through fatigue, may influence a technically skilled move as the FT is. Twenty-eight under 17 basketball players were studied while shooting FTs on a regular indoor basketball court. We investigated FT accuracy in young male basketball players shooting at three different HRs: at rest, at 50% and at 80% of maximum experimentally obtained HR value. We found no significant FT percentage difference between rest and 50% of the maximum HR (FT percentage about 80%; P > 0.05). Differently, at 80% of the maximum HR the FT percentage decreased significantly by more than 20% (P < 0.001) down to about 60%. No preliminary warm-up is needed before entering game for the FT accuracy. Furthermore, we speculate that time-consuming, cooling-off routines usually performed by shooters before each FT may be functional to improve its accuracy.

Influence of various metal oxides on mechanical and physical properties of heat-cured polymethyl methacrylate denture base resins.

PubMed

Asar, Neset Volkan; Albayrak, Hamdi; Korkmaz, Turan; Turkyilmaz, Ilser

2013-08-01

To evaluate the effect of various metal oxides on impact strength (IS), fracture toughness (FT), water sorption (WSP) and solubility (WSL) of heat-cured acrylic resin. Fifty acrylic resin specimens were fabricated for each test and divided into five groups. Group 1 was the control group and Group 2, 3, 4 and 5 (test groups) included a mixture of 1% TiO2 and 1% ZrO2, 2% Al2O3, 2% TiO2, and 2% ZrO2 by volume, respectively. Rectangular unnotched specimens (50 mm × 6.0 mm × 4.0 mm) were fabricated and droptower impact testing machine was used to determine IS. For FT, compact test specimens were fabricated and tests were done with a universal testing machine with a cross-head speed of 5 mm/min. For WSP and WSL, discshaped specimens were fabricated and tests were performed in accordance to ISO 1567. ANOVA and Kruskal-Wallis tests were used for statistical analyses. IS and FT values were significantly higher and WSP and WSL values were significantly lower in test groups than in control group (P<.05). Group 5 had significantly higher IS and FT values and significantly lower WSP values than other groups (P<.05) and provided 40% and 30% increase in IS and FT, respectively, compared to control group. Significantly lower WSL values were detected for Group 2 and 5 (P<.05). Modification of heat-cured acrylic resin with metal oxides, especially with ZrO2, may be useful in preventing denture fractures and undesirable physical changes resulting from oral fluids clinically.

Completion Report for Well ER-2-2 Corrective Action Unit 97: Yucca Flat/Climax Mine, Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wurtz, Jeffrey

Well ER-2-2 was drilled for the U.S. Department of Energy, Nevada National Security Administration Nevada Field Office in support of the Underground Test Area (UGTA) Activity. The well was drilled from January 17 to February 8, 2016, as part of the Corrective Action Investigation Plan (CAIP) for Corrective Action Unit 97: Yucca Flat/Climax Mine, Nevada Test Site, Nevada. The primary purpose of the well was to collect hydrogeologic data to evaluate uncertainty in the flow and transport conceptual model and its contamination boundary forecasts, and to detect radionuclides in groundwater from the CALABASH (U2av) underground test. Well ER-2-2 was notmore » completed as planned due to borehole stability problems. As completed, the well includes a piezometer (p1) to 582 meters (m) (1,909 feet [ft]) below ground surface (bgs) installed in the Timber Mountain lower vitric-tuff aquifer (TMLVTA) and a 12.25-inch (in.) diameter open borehole to 836 m (2,743 ft) bgs in the Lower tuff confining unit (LTCU). A 13.375-in. diameter carbon-steel casing is installed from the surface to a depth of 607 m (1,990 ft) bgs. Data collected during borehole construction include composite drill cutting samples collected every 3.0 m (10 ft), geophysical logs to a depth of 672.4 m (2,206 ft) bgs, water-quality measurements (including tritium), water-level measurements, and slug test data. The well penetrated 384.05 m (1,260 ft) of Quaternary alluvium, 541.93 m (1,778 ft) of Tertiary Volcanics (Tv) rocks, and 127.71 m (419 ft) of Paleozoic carbonates. The stratigraphy and lithology were generally as expected. However, several of the stratigraphic units were significantly thicker then predicted—principally, the Tunnel formation (Tn), which had been predicted to be 30 m (100 ft) thick; the actual thickness of this unit was 268.22 m (880 ft). Fluid depths were measured in the borehole during drilling as follows: (1) in the piezometer (p1) at 552.15 m (1,811.53 ft) bgs and (2) in the main casing (m1) at 551.69 m (1,810.01 ft) bgs. As expected, field measurements for tritium were above the Safe Drinking Water Act limit (20,000 picocuries per liter) for a portion of the Tertiary volcanic section near the water table. Tritium concentrations were at or near the field detection limit in the Lower carbonate aquifer (LCA) while drilling. During drilling, a sample was collected while circulating in the LCA. The sample was submitted for off-site laboratory analysis. The sample results indicated low but measurable tritium concentrations. All Fluid Management Plan requirements were met during drilling activities.« less

Promoter difference of LcFT1 is a leading cause of natural variation of flowering timing in different litchi cultivars (Litchi chinensis Sonn.).

PubMed

Ding, Feng; Zhang, Shuwei; Chen, Houbin; Su, Zuanxian; Zhang, Rong; Xiao, Qiusheng; Li, Hongli

2015-12-01

Litchi (Litchi chinensis) is an important subtropical evergreen fruit crop with high commercial value due to its high nutritional values and favorable tastes. However, irregular bearing attributed to unstable flowering is a major ongoing problem for litchi producers. There is a need to better understand the genetic and molecular mechanisms underlying the reproductive process in litchi. In a previous study, our laboratory had analyzed the transcriptome of litchi leaves before and after low-temperature treatment with RNA-seq technology. Herein, we demonstrated that litchi flowering was induced by low-temperature and identified two FLOWERING LOCUS T (FT) homologue genes named LcFT1 and LcFT2, respectively. We found that low-temperature could only induce LcFT1 expression in leaves, but could not induce LcFT2 expression. Heterologous expression of LcFT1 in transgenic tobacco and Arabidopsis plants induced their precocious flowering. These results indicate that LcFT1 plays a pivotal role in litchi floral induction by low-temperature. In addition, we found that two types of LcFT1 promoter existed in different litchi cultivars. The LcFT1 promoters in the early-flowering cultivars belonged to one type whereas LcFT1 promoters in the late-flowering belonged to another one. LcFT1 promoter in the early-flowering cultivars was more sensitive to low-temperature than that of the late-flowering cultivars was, which may be caused by the different cis-acting elements, including MYC, MYB, ABRE, and WRKY cis-acting elements, which were found to be present in the LcFT1 promoter sequences of the early-flowering cultivars. This difference may be responsible for the different requirements of low-temperature for floral induction in the early- and late-flowering cultivars of litchi. Taken together, the difference in LcFT1 promoter sequences may be one of the leading cause for the natural variation of flowering timing in different litchi cultivars. Our study has provided valuable genetic basis for cross-breeding of litchi cultivars to generate new litchi cultivars for overcoming the problem of unstable flowering for litchi producers. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Is glycated albumin useful for differential diagnosis between fulminant type 1 diabetes mellitus and acute-onset autoimmune type 1 diabetes mellitus?

PubMed

Koga, Masafumi; Kanehara, Hideo; Bando, Yukihiro; Morita, Shinya; Kasayama, Soji

2015-12-07

Markedly elevated plasma glucose and relatively low HbA1c compared to plasma glucose is one diagnostic criterion for fulminant type 1 diabetes mellitus (FT1DM). Glycated albumin (GA) is a glycemic control marker that reflects glycemic control in shorter period than HbA1c. This study investigated whether GA is useful for differential diagnosis between FT1DM and acute-onset autoimmune type 1 diabetes mellitus (T1ADM) or not. This study included 38 FT1DM patients and 31 T1ADM patients in whom both HbA1c and GA were measured at the time of diagnosis. In FT1DM patients, as compared to T1ADM patients, both HbA1c and GA were significantly lower (HbA1c; 6.6±0.9% vs. 11.7±2.6%, P<0.0001, GA; 22.9±4.8% vs. 44.3±8.3%, P<0.0001). For differential diagnosis between FT1DM and T1ADM, ROC analysis showed that the optimum cut-off value for GA was 33.5% with sensitivity and specificity of 97.4% and 96.8%, respectively, while the optimum cut-off value for HbA1c was 8.7% with sensitivity and specificity of 100% and 83.9%, respectively. GA also may be useful for the differential diagnosis between FT1DM and T1ADM when the cut-off value can be set at 33.5%. Copyright © 2015 Elsevier B.V. All rights reserved.

Remotely sensed MODIS wetland components for assessing the variability of methane emissions in Indian tropical/subtropical wetlands

NASA Astrophysics Data System (ADS)

Bansal, Sangeeta; Katyal, Deeksha; Saluja, Ridhi; Chakraborty, Monojit; Garg, J. K.

2018-02-01

Temperature and area fluctuations in wetlands greatly influence its various physico-chemical characteristics, nutrients dynamic, rates of biomass generation and decomposition, floral and faunal composition which in turn influence methane (CH4) emission rates. In view of this, the present study attempts to up-scale point CH4 flux from the wetlands of Uttar Pradesh (UP) by modifying two-factor empirical process based CH4 emission model for tropical wetlands by incorporating MODIS derived wetland components viz. wetland areal extent and corresponding temperature factors (Ft). This study further focuses on the utility of remotely sensed temperature response of CH4 emission in terms of Ft. Ft is generated using MODIS land surface temperature products and provides an important semi-empirical input for up-scaling CH4 emissions in wetlands. Results reveal that annual mean Ft values for UP wetlands vary from 0.69 (2010-2011) to 0.71(2011-2012). The total estimated area-wise CH4 emissions from the wetlands of UP varies from 66.47 Gg yr-1with wetland areal extent and Ft value of 2564.04 km2 and 0.69 respectively in 2010-2011 to 88.39 Gg yr-1with wetland areal extent and Ft value of 2720.16 km2 and 0.71 respectively in 2011-2012. Temporal analysis of estimated CH4 emissions showed that in monsoon season estimated CH4 emissions are more sensitive to wetland areal extent while in summer season sensitivity of estimated CH4 emissions is chiefly controlled by augmented methanogenic activities at high wetland surface temperatures.

Structure of the top of the Karnak Limestone Member (Ste. Genevieve) in Illinois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bristol, H.M.; Howard, R.H.

1976-01-01

To facilitate petroleum exploration in Illinois, the Illinois State Geological Survey presents a structure map (for most of southern Illinois) of the Karnak Limestone Member--a relatively pure persistent limestone unit (generally 10 to 35 ft thick) in the Ste. Genevieve Limestone of Genevievian age. All available electric logs and selected studies of well cuttings were used in constructing the map. Oil and gas development maps containing Karnak-structure contours are on open file at the ISGS.

Hydrologic influences on water-level changes in the Eastern Snake River Plain aquifer at and near the Idaho National Laboratory, Idaho, 1949-2014

USGS Publications Warehouse

Bartholomay, Roy C.; Twining, Brian V.

2015-01-01

Geophysical logs indicate that most of the wells evaluated will maintain their current production until the water level declines to the depth of the pump. A few of the wells may become less productive once the water level gets to within about 5 ft from the top of the pump. Wells most susceptible to future drought cycles are those in the northeastern and northwestern areas of the INL.

26 CFR 1.684-1 - Recognition of gain on transfers to certain foreign trusts and estates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... recognize gain at the time of the transfer equal to the excess of the fair market value of the property... portion of FT. Under paragraph (a)(1) of this section, A recognizes gain at the time of the transfer equal... of 1000X, and property R, with a fair market value of 2000X, to FT. At the time of the transfer, A's...

Financial feasibility of a log sort yard handling small-diameter logs: A preliminary study

Treesearch

Han-Sup Han; E. M. (Ted) Bilek; John (Rusty) Dramm; Dan Loeffler; Dave Calkin

2011-01-01

The value and use of the trees removed in fuel reduction thinning and restoration treatments could be enhanced if the wood were effectively evaluated and sorted for quality and highest value before delivery to the next manufacturing destination. This article summarizes a preliminary financial feasibility analysis of a log sort yard that would serve as a log market to...

High urinary bisphenol A concentrations in workers and possible laboratory abnormalities.

PubMed

Wang, Feng; Hua, Jing; Chen, Minjian; Xia, Yankai; Zhang, Qi; Zhao, Renzheng; Zhou, Weixin; Zhang, Zhengdong; Wang, Bingling

2012-09-01

Bisphenol A (BPA) is widely used in epoxy resins in China. There are few reports on the adverse health effects of occupational exposure to BPA. This study examined associations between urinary BPA concentrations in workers and laboratory parameters for health status. Spot urine checks at the end shift on Friday were used for cross-sectional analysis of BPA concentrations, and blood or urinary markers of liver function, glucose homeostasis, thyroid function and cardiovascular diseases were measured. The 28 participants were workers in two semiautomatic epoxy resin factories. The average urinary BPA concentration was 55.73±5.48 ng/ml (geometric mean ± geometric SD) (range 5.56-1934.85 ng/ml). After adjusting for urine creatinine (Cr), it was 31.96±4.42 μg/g Cr (geometric mean ± geometric SD) (range 4.61-1253.69 μg/g Cr). BPA feeding operators showed the highest concentrations, over 10 times those of the crushing and packing and office workers. Higher BPA concentrations were associated with clinically abnormal concentrations of FT3, FT4, TT3, TT4, thyroid-stimulating hormone, glutamic-oxaloacetic transaminase and γ-glutamyl transferase. Workers with higher BPA concentrations showed higher FT3 concentrations (linear trend: p<0.001). Bivariate correlation tests for laboratory analytes within normal limits showed FT3 to be positively associated with logged BPA concentrations, r=0.57, p=0.002. FT4 was positively associated with lactate dehydrogenase, r=0.45, p=0.020, and insulin was positively associated with thyroid-stimulating hormone with r=0.57, p=0.009. Higher occupational BPA exposure, reflected in urinary concentrations of BPA, may be associated with thyroid hormone disruption.

Geomorphology of the Trinity River floodplain in Dallas County, Texas

NASA Astrophysics Data System (ADS)

Haugen, B. D.; Roig-Silva, C.; Manning, A. R.; Harrelson, D. W.; Olsen, R. S.; Dunbar, J. P.; Pearson, M. L.

2010-12-01

Data from more than 1,800 geologic borings and over 500 cone penetrometer tests (CPTs) were used to characterize the geomorphology of the Trinity River floodplain in the Dallas Metropolitan Area. Historical maps, aerial photographs and other published information were used to prepare a preliminary geomorphic map. Boring logs and CPT data were then used to refine the preliminary map, produce a series of two-dimensional (2D) and three-dimensional (3D) cross sections, and interpret the recent geologic history of the area. Geomorphologic interpretations - most importantly the locations of paleo-channel deposits of sands and gravels - were used to identify reaches of the levees managed by the United States Army Corps of Engineers (USACE) and the City of Dallas that may be at significant risk for under-seepage. Boring logs and CPT data collected atop the levees were used to assess through-seepage risks. Local bedrock is comprised of cretaceous-age Eagle Ford Shale and Austin Chalk. Depth to bedrock in the study area averaged 14.6 m (47.8 ft). The uppermost surface of bedrock has been deeply incised by a meandering river. Vertical relief between the shallowest bedrock sections and deepest portion of the incised paleo-channel is more than 15 m (50 ft). In places the incised paleo-channel is more than 0.8 km (0.5 mi) wide. These data confirm the presence of an erosional unconformity between local bedrock and overlying quaternary floodplain deposits. The observed erosional unconformity is attributed to a higher-energy fluvial environment that occurred as a result of a drop in base level. Recent floodplain deposits consist of interlobate point bar, channel and overbank sediments that are generally distributed in a fining-upward sequence. Buried channel dimensions vary widely, but are more than 250 m (820 ft) in some areas - much larger than the current channel. A semi-continuous basal layer of quaternary sands and gravels approximately 2 to 5 m (7 to 16 ft) thick exists in much of the study area. These data indicate that the discharge rate of the Trinity River today is at its lowest since quaternary deposition began. Large terraces of varying geometry and elevation observed at the edge of the floodplain show that the Trinity River has been geographically constrained to its current floodplain since the late Cretaceous, and perhaps even earlier.

New Agegraphic Pilgrim Dark Energy in f(T, TG) Gravity

NASA Astrophysics Data System (ADS)

Jawad, Abdul; Debnath, Ujjal

2015-08-01

In this work, we briefly discuss a novel class of modified gravity like f(T, TG) gravity. In this background, we assume the new agegraphic version of pilgrim dark energy and reconstruct f(T, TG) models for two specific values of s. We also discuss the equation of state parameter, squared speed of sound and wDE-w‧DE plane for these reconstructed f(T, TG) models. The equation of state parameter provides phantom-like behavior of the universe. The wDE-w‧DE plane also corresponds to ΛCDM limit, thawing and freezing regions for both models.

Precision Half-life Measurement of 25Al

NASA Astrophysics Data System (ADS)

Long, Jacob; Ahn, Tan; Allen, Jacob; Bardayan, Daniel; Becchetti, Fredrich; Blankstein, Drew; Brodeur, Maxime; Burdette, Daniel; Frentz, Bryce; Hall, Matthew; Kelly, James; Kolata, James; O'Malley, Patrick; Schultz, Bradley; Strauss, Sabrina; Valverde, Adrian; TwinSol Collaboration

2017-09-01

In recent years, precision measurements have led to considerable advances in several areas of physics, including fundamental symmetry. Precise determination of ft values for superallowed mixed transitions between mirror nuclides could provide an avenue to test the theoretical corrections used to extract the Vud matrix element from superallowed pure Fermi transitions. Calculation of the ft value requires the half-life, branching ratio, and Q value. 25Al decay is of particular interest as its half-life is derived from a series of conflicting measurements, and the largest uncertainty on the ft value stems from the half-life uncertainty. The life-time was determined by the β counting of implanted 25Al on a Ta foil that was removed from the beam for counting. The 25Al beam was produced by a transfer reaction and separated by the TwinSol facility of the Nuclear Science Laboratory of the University of Notre Dame. The 25Al results will be presented with preliminary results of more recent half-life measurements. The National Science Foundation.

Change of Direction Ability Performance in Cerebral Palsy Football Players According to Functional Profiles

PubMed Central

Reina, Raúl; Sarabia, Jose M.; Yanci, Javier; García-Vaquero, María P.; Campayo-Piernas, María

2016-01-01

The aims of the present study were to evaluate the validity and reliability of the two different change of direction ability (CODA) tests in elite football players with cerebral palsy (CP) and to analyse the differences in performance of this ability between current functional classes (FT) and controls. The sample consisted of 96 international cerebral palsy football players (FPCP) and 37 football players. Participants were divided into four different groups according to the International Federation of Cerebral Palsy Football (IFCPF) classes and a control group (CG): FT5 (n = 8); FT6 (n = 12); FT7 (n = 62); FT8 (n = 14); and CG (n = 37). The reproducibility of Modified Agility Test (MAT) and Illinois Agility Test (IAT) (ICC = 0.82–0.95, SEM = 2.5–5.8%) showed excellent to good values. In two CODA tests, CG performed faster scores compared with FPCP classes (p < 0.01, d = 1.76–3.26). In IAT, FT8 class comparisons regarding the other classes were: FT5 (p = 0.047, d = 1.05), FT6 (p = 0.055, d = 1.19), and FT7 (p = 0.396, d = 0.56). With regard to MAT, FT8 class was also compared with FT5 (p = 0.006, d = 1.30), FT6 (p = 0.061, d = 0.93), and FT7 (p = 0.033, d = 1.01). No significant differences have been found between FT5, FT6, and FT7 classes. According to these results, IAT and MAT could be useful and reliable and valid tests to analyse CODA in FPCP. Each test (IAT and MAT) could be applied considering the cut point that classifiers need to make a decision about the FT8 class and the other FT classes (FT5, FT6, and FT7). PMID:26779037

Lumber volume and value recovery from small-diameter black cherry, sugar maple, and red oak logs

Treesearch

Jan Wiedenbeck; Matthew Scholl; Paul Blankenhorn; Chuck Ray

2017-01-01

While only a very small percentage of hardwood logs sawn by conventional sawmills in the U.S. have small-end diameters less than 10 in, portable and scragg mills often saw smaller logs. With the closure of regionally important oriented strand board and pulpwood operations, small-diameter logs are considered to have no value in some markets. This study was...

Characterization of Vadose Zone Sediment: RCRA Borehole 299-E33-338 Located Near the B-BX-BY Waste Management Area

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lindenmeier, Clark W.; Serne, R. Jeffrey; Bjornstad, Bruce N.

2003-09-11

This report summarizes data collected from samples in borehole 299-E33-338 (C3391). Borehole 299-E33-338 was drilled for two purposes. One purpose was for installation of a RCRA ground-water monitoring well and the other was to characterize the in situ soils and background porewater chemistry near WMA B-BX-BY that have been largely uncontaminated by tank farm and crib and trench discharge operations. This borehole was drilled just outside the southeast fence line of the B tank farm. The borehole was drilled between July 23 and August 8, 2001 to a total depth of 80.05 m (275.75 ft) bgs using the cable-tool methodmore » (Horton 2002). The water table was contacted at 77.5 m (254.2 ft) bgs and the top of basalt at 82.6 m (271 ft) bgs. Samples to the top of basalt were collected via a drive barrel/splitspoon, before switching to a hard tool to drill 5 feet into the basalt. Nearly continuous core was obtained down to a depth of ~78.6 m (258 ft) bgs. Two hundred and two 2-ft long by 4-in diameter cores were retrieved, which accounts for ~75% the total length of the borehole. Each 2-ft splitspoon contained two 1-ft lexan-lined core segments. The lithology of this borehole was summarized onto a field geologist's log by a CH2M HILL Hanford Group, Inc. geologist (L. D. Walker); subsequently visual inspection of the cores was performed in the laboratory by K. A. Lindsey (Kennedy/Jenks), K. D. Reynolds (Duratek), and B. N. Bjornstad (Pacific Northwest National Laboratory), who also collected 24 samples for paleomagnetic analysis. Subsamples were taken from all 102 cores for moisture content (Table B.1). In addition, 21 core subsamples were collected from a depth of geological interest for mineralogical and geochemical analysis. Data from these samples allow for comparison of uncontaminated versus contaminated soils to better understand the contributions of tank wastes and other wastewaters on the vadose zone in and around WMA B-BX-BY.« less

Integrated study of Mississippian Lodgepole Waulsortian Mounds, Williston Basin, USA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kupecz, J.A.; Arestad, J.F.; Blott, J. E.

1996-06-01

Waulsortian-type carbonate buildups in the Mississippian Lodgepole Formation, Williston Basin, constitute prolific oil reservoirs. Since the initial discovery in 1993, five fields have been discovered: Dickinson Field (Lodgepole pool); Eland Field; Duck Creek Field, Versippi Field; and Hiline Field. Cumulative production (October, 1995) is 2.32 million barrels of oil and 1.34 BCF gas, with only 69,000 barrels of water. Oil gravity ranges from 41.4 to 45.3 API. Both subsurface cores from these fields as well as outcrop (Bridget Range, Big Snowy and Little Belt Mountains, Montana) are composed of facies representing deposition in mound, reworked mound, distal reworked mound, proximalmore » flank, distal flank, and intermound settings. Porosity values within the mound and reworked mound facies are up to 15%; permeability values (in places fracture-enhanced) are up to tens of Darcies. Geometries of the mounds are variable. Mound thicknesses in the subsurface range from approximately 130-325 feet (40-100 meters); in outcrop thicknesses range from less than 30 ft (9 m) to over 250 ft (76 m). Subsurface areal dimensions range from approximately 0.5 x 1.0 mi (0.8 x 1.6 km) to 3.5 x 5.5 mi (5.6 x 8.8 km). Integration of seismic data with core and well-log models sheds light on the exploration for Lodgepole mounds. Seismic modeling of productive mounds in the Dickinson and Eland fields identifies characteristics useful for exploration, such as local thickening of the Lodgepole to Three Forks interval. These observations are confirmed in reprocessed seismic data across Eland field and on regional seismic data. Importantly, amplitude versus offset modeling identifies problems with directly detecting and identifying porosity within these features with amplitude analyses. In contrast, multicomponent seismic data has great potential for imaging these features and quantifying porous zones within them.« less

Hydrologic Tests at Characterization Wells R-9i, R-13, R-19, R-22, and R-31, Revision 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.G.McLin; W.J. Stone

2004-06-01

Hydrologic information is essential for environmental efforts at Los Alamos National Laboratory. Testing at new characterization wells being drilled to the regional aquifer (''R wells'') to improve the conceptual hydrogeologic model of the Pajarito Plateau is providing such information. Field tests were conducted on various zones of saturation penetrated by the R wells to collect data needed for determining hydraulic properties. This document provides details of the design and execution of testing as well as an analysis of data for five new wells: R-9i, R-13, R-19, R-22, and R-31. One well (R-13) was evaluated by a pumping test and themore » rest (R-9i, R-19, R-22, and R-31) were evaluated by injection tests. Characterization well R-9i is located in Los Alamos Canyon approximately 0.3 mi west of the Route 4/Route 502 intersection. It was completed at a depth of 322 ft below ground surface (bgs) in March 2000. This well was constructed with two screens positioned below the regional water table. Both screens were tested. Screen 1 is completed at about 189-200 ft bgs in fractured basalt, and screen 2 is completed at about 270-280 ft bgs in massive basalt. Specific capacity analysis of the screen 1 data suggests that the fractured basalt has a transmissivity (T) of 589 ft{sup 2}/day and corresponds to a hydraulic conductivity (K) of 7.1 ft/day based on a saturated thickness of 83 ft. The injection test data from the massive basalt near screen 2 were analyzed by the Bouwer-Rice slug test methodology and suggest that K is 0.11 ft/day, corresponding to a T of about 2.8 ft{sup 2}/day based on a saturated thickness of 25 ft. Characterization well R-13 is located in Mortandad Canyon just west of the eastern Laboratory boundary. It was completed at a depth of 1029 ft bgs in February 2002. This well was constructed with one 60-ft long screen positioned about 125 ft below the regional water table. This screen is completed at about 958-1019 ft bgs and straddles the geologic contact between the Puye fanglomerate and unassigned pumiceous units. The specific capacity analysis of a 12 minute pumping test indicates that the Puye fanglomerates near the R-13 screen have a T of 5269 ft{sup 2}/day and correspond to a hydraulic conductivity (K) of 17.6 ft/day based on a saturated thickness of 300 ft. Characterization well R-19 is located east of firing site IJ in Technical Area (TA) 36 on the mesa between Three-mile and Potrillo Canyons. It was completed at a depth of 1885 ft bgs in April 2000. This well was constructed with two screens positioned above the regional water table and five screens positioned below the regional water table. Only the bottom two screens were tested. Screen 6 is completed at about 1727-1734 ft bgs in Puye fanglomerate, and screen 7 is completed at about 1832-1849 ft bgs in Puye fanglomerate. Specific capacity analysis of the screen 6 data suggests that T is about 6923 ft{sup 2}/day and corresponds to a K of 18.6 ft/day based on a saturated thickness of 373 ft. Specific capacity analysis of the screen 7 data suggests that T is about 8179 ft{sup 2}/day and corresponds to a K of 22.0 ft/day based on a saturated thickness of 373 ft. Characterization well R-22 is located on Mesita del Buey between Canada del Buey and Pajarito Canyons immediately east of Material Disposal Area (MDA) G in TA-54. It was completed at a depth of 1489 ft bgs in October 2000. This well was constructed with five screens positioned at or below the regional water table; however, only screens 2-5 were tested. Screen 1 is completed at the regional water table at about 872-914 ft bgs in Cerros del Rio basalt. Screen 2 is completed at about 947-989 ft bgs in Cerros del Rio basalt. Screen 3 is completed at about 1272-1279 ft bgs in Puye fanglomerate. Screen 4 is completed at about 1378-1452 ft bgs in older basalt. Screen 5 is completed at about 1447-1452 ft bgs in older fanglomerate. Bouwer-Rice analyses of the injection-test recovery data suggest K values of 0.04, 0.32, 0.54, and 0.27 ft/day for screens 2, 3, 4, and 5, respectively. These values correspond to T values of 2.8, 15.8, 26.5, and 11.6 ft{sup 2}/day, respectively, for screens 2, 3, 4, and 5. These analyses are based on saturated thicknesses of 69.5 ft, 49.4 ft, 49.0 ft, and 43.0 ft, respectively. Characterization well R-31 is located at TA-39 in the north fork of lower Ancho Canyon. It was completed at a depth of 1103 ft bgs in April 2000. This well was constructed with one screen positioned above the regional water table, and four screens position at or below the regional water table.« less

VizieR Online Data Catalog: CoRoT red giants abundances (Morel+, 2014)

NASA Astrophysics Data System (ADS)

Morel, T.; Miglio, A.; Lagarde, N.; Montalban, J.; Rainer, M.; Poretti, E.; Eggenberger, P.; Hekker, S.; Kallinger, T.; Mosser, B.; Valentini, M.; Carrier, F.; Hareter, M.; Mantegazza, L.

2014-02-01

The equivalent widths were measured manually assuming Gaussian profiles or Voigt profiles for the few lines with extended damping wings. Lines with an unsatisfactory fit or significantly affected by telluric features were discarded. Only values eventually retained for the analysis are provided. For the chemical abundances, the usual notation is used: [X/Y]=[log({epsilon}(X))-log({epsilon}(Y))]star - [log({epsilon}(X))-log({epsilon}(Y))]⊙ with log{epsilon}(X)=12+log[N(X)/N(H)] (N is the number density of the species). For lithium, the following notation is used: [Li/H]=log(N(Li))star-log(N(Li))⊙. The adopted solar abundances are taken from Grevesse & Sauval (1998SSRv...85..161G), except for Li for which we adopt our derived values: log({epsilon}(Li))⊙=1.09 and 1.13 in LTE and NLTE, respectively (see text). All the abundances are computed under the assumption of LTE, except Li for which values corrected for departures from LTE using the data of Lind et al. (2009A&A...503..541L) are also provided. All the quoted error bars are 1-sigma uncertainties. (6 data files).

[Determination and prediction for vapor pressures of organophosphate flame retardants by gas chromatography].

PubMed

Wang, Qingzhi; Zhao, Hongxia; Wang, Yan; Xie, Qing; Chen, Jingwen; Quan, Xie

2017-09-08

Organophosphate flame retardants (OPFRs) are ubiquitous in the environment. To better understand and predict their environmental transport and fate, well-defined physicochemical properties are required. Vapor pressures ( P ) of 14 OPFRs were estimated as a function of temperature ( T ) by gas chromatography (GC), while 1,1,1-trichioro-2,2-bis (4-chlorophenyl) ethane ( p,p '-DDT) was acted as a reference substance. Their log P GC values and internal energies of phase transfer (△ vap H ) ranged from -6.17 to -1.25 and 74.1 kJ/mol to 122 kJ/mol, respectively. Substitution pattern and molar volume ( V M ) were found to be capable of influencing log P GC values of the OPFRs. The halogenated alkyl-OPFRs had lower log P GC values than aryl-or alkyl-OPFRs. The bigger the molar volume was, the smaller the log P GC value was. In addition, a quantitative structure-property relationship (QSPR) model of log P GC versus different relative retention times (RRTs) was developed with a high cross-validated value ( Q 2 cum ) of 0.946, indicating a good predictive ability and stability. Therefore, the log P GC values of the OPFRs without standard substance can be predicted by using their RRTs on different GC columns.

Determination and prediction of octanol-air partition coefficients for organophosphate flame retardants.

PubMed

Wang, Qingzhi; Zhao, Hongxia; Wang, Yan; Xie, Qing; Chen, Jingwen; Quan, Xie

2017-11-01

Organophosphate flame retardants (OPFRs) have attracted wide concerns due to their toxicities and ubiquitous occurrence in the environment. In this work, Octanol-air partition coefficient (K OA ) for 14 OPFRs including 4 halogenated alkyl-, 5 aryl- and 5 alkyl-OPFRs, were estimated as a function of temperature using a gas chromatographic retention time (GC-RT) method. Their log K OA-GC values and internal energies of phase transfer (Δ OA U/kJmol -1 ) ranged from 8.03 to 13.0 and from 69.7 to 149, respectively. Substitution pattern and molar volume (V M ) were found to be capable of influencing log K OA-GC values of OPFRs. The halogenated alkyl-OPFRs had higher log K OA-GC values than aryl- or alkyl-OPFRs. The bigger the molar volume was, the greater the log K OA-GC values increased. In addition, a predicted model of log K OA-GC versus different relative retention times (RRTs) was developed with a high cross-validated value (Q 2 (cum) ) of 0.951, indicating a good predictive ability and stability. Therefore, the log K OA-GC values of the remaining OPFRs can be predicted by using their RRTs on different GC columns. Copyright © 2017 Elsevier Inc. All rights reserved.

Effects of social sustainability signaling on neural valuation signals and taste-experience of food products

PubMed Central

Enax, Laura; Krapp, Vanessa; Piehl, Alexandra; Weber, Bernd

2015-01-01

Value-based decision making occurs when individuals choose between different alternatives and place a value on each alternative and its attributes. Marketing actions frequently manipulate product attributes, by adding, e.g., health claims on the packaging. A previous imaging study found that an emblem for organic products increased willingness to pay (WTP) and activity in the ventral striatum (VS). The current study investigated neural and behavioral processes underlying the influence of Fair Trade (FT) labeling on food valuation and choice. Sustainability is an important product attribute for many consumers, with FT signals being one way to highlight ethically sustainable production. Forty participants valuated products in combination with an FT emblem or no emblem and stated their WTP in a bidding task while in an MRI scanner. After that, participants tasted—objectively identical—chocolates, presented either as “FT” or as “conventionally produced”. In the fMRI task, WTP was significantly higher for FT products. FT labeling increased activity in regions important for reward-processing and salience, that is, in the VS, anterior and posterior cingulate, as well as superior frontal gyrus. Subjective value, that is, WTP was correlated with activity in the ventromedial prefrontal cortex (vmPFC). We find that the anterior cingulate, VS and superior frontal gyrus exhibit task-related increases in functional connectivity to the vmPFC when an FT product was evaluated. Effective connectivity analyses revealed a highly probable directed modulation of the vmPFC by those three regions, suggesting a network which alters valuation processes. We also found a significant taste-placebo effect, with higher experienced taste pleasantness and intensity for FT labeled chocolates. Our results reveal a possible neural mechanism underlying valuation processes of certified food products. The results are important in light of understanding current marketing trends as well as designing future interventions that aim at positively influencing food choice. PMID:26441576

Sound attenuation of fiberglass lined ventilation ducts

NASA Astrophysics Data System (ADS)

Albright, Jacob

Sound attenuation is a crucial part of designing any HVAC system. Most ventilation systems are designed to be in areas occupied by one or more persons. If these systems do not adequately attenuate the sound of the supply fan, compressor, or any other source of sound, the affected area could be subject to an array of problems ranging from an annoying hum to a deafening howl. The goals of this project are to quantify the sound attenuation properties of fiberglass duct liner and to perform a regression analysis to develop equations to predict insertion loss values for both rectangular and round duct liners. The first goal was accomplished via insertion loss testing. The tests performed conformed to the ASTM E477 standard. Using the insertion loss test data, regression equations were developed to predict insertion loss values for rectangular ducts ranging in size from 12-in x 18-in to 48-in x 48-in in lengths ranging from 3ft to 30ft. Regression equations were also developed to predict insertion loss values for round ducts ranging in diameters from 12-in to 48-in in lengths ranging from 3ft to 30ft.

Molecular structure, vibrational spectroscopic, first order hyperpolarizability and HOMO-LUMO studies of 7-amino-8-oxo-3-vinyl-5-thia-1-azabicyclo[4.2.0]oct-2-ene-2-carboxylic acid

NASA Astrophysics Data System (ADS)

Ramalingam, M.; Sethuraman, V.; Sundaraganesan, N.

2011-02-01

The FT-IR and FT-Raman spectra of 7-amino-8-oxo-3-vinyl-5-thia-1-azabicyclo[4.2.0]oct-2-ene-2-carboxylic acid (7AVCA) were recorded in the region 4000-400 cm -1 and 3500-10 cm -1, respectively. Quantum chemical calculations of energies, geometrical structure and vibrational wavenumbers were carried out by ab initio HF and density functional theoretical methods invoking 6-311G(d,p) basis set. The differences between the observed and scaled wavenumber values of most of the fundamentals are very small. The electric dipole moment ( μ) and the first order hyperpolarizability ( β0) values have been computed quantum mechanically. The calculated results show that 7AVCA may have microscopic nonlinear optical (NLO) behavior with non-zero values. A detailed interpretation of the FT-IR and FT-Raman spectra of 7AVCA is reported. The theoretical IR and Raman spectra of 7AVCA have also been constructed. The calculated HOMO and LUMO energies show that the charge transfer occurs within the molecule.

Molecular structure, vibrational spectroscopic, first order hyperpolarizability and HOMO-LUMO studies of 7-amino-8-oxo-3-vinyl-5-thia-1-azabicyclo[4.2.0]oct-2-ene-2-carboxylic acid.

PubMed

Ramalingam, M; Sethuraman, V; Sundaraganesan, N

2011-02-01

The FT-IR and FT-Raman spectra of 7-amino-8-oxo-3-vinyl-5-thia-1-azabicyclo[4.2.0]oct-2-ene-2-carboxylic acid (7AVCA) were recorded in the region 4000-400 cm(-1) and 3500-10 cm(-1), respectively. Quantum chemical calculations of energies, geometrical structure and vibrational wavenumbers were carried out by ab initio HF and density functional theoretical methods invoking 6-311G(d,p) basis set. The differences between the observed and scaled wavenumber values of most of the fundamentals are very small. The electric dipole moment (μ) and the first order hyperpolarizability (β0) values have been computed quantum mechanically. The calculated results show that 7AVCA may have microscopic nonlinear optical (NLO) behavior with non-zero values. A detailed interpretation of the FT-IR and FT-Raman spectra of 7AVCA is reported. The theoretical IR and Raman spectra of 7AVCA have also been constructed. The calculated HOMO and LUMO energies show that the charge transfer occurs within the molecule. Copyright © 2010 Elsevier B.V. All rights reserved.

Schedule-induced polydipsia in the spontaneously hypertensive rat and its relation to impulsive behaviour.

PubMed

Ibias, Javier; Pellón, Ricardo

2011-09-30

Eight Spontaneously Hypertensive Rat (SHR), 8 Wistar-Kyoto (WKY) and 8 Wistar rats, all male, maintained at 80-85% of their free-feeding weight by controlled access to food, were exposed to a series of fixed time (FT) schedules whereby food pellets were regularly delivered regardless of the animals' behaviour. The FT values used were 9, 15, 30, 60, 120 and 180 s, with the order of presentation of the schedules among the animals being counterbalanced (except under the FT 120-s and 180-s schedules, which were successively presented as the last two of the series). Due to freely available access to water, the animals developed schedule-induced drinking under all FT schedules, marked by the characteristic bitonic function that relates the number of licks and amount of water drunk to the length of the inter-food interval. Wistar and WKY rats displayed maximum drinking under an FT 15-s schedule, with WKY rats registering lower quantities across all FT values. Among SHR rats, maximum schedule-induced polydipsia was observed under the FT 30-s schedule, with a rightward shift in the bitonic function compared to controls. For long FT values, the temporal distribution of licks within inter-food intervals was shifted slightly towards the right in the SHR rats. In a subsequent study, only the SHR and Wistar rats were used, and the animals were exposed to a delay-discounting procedure. The rats were faced with successive choices, in which they could choose between an immediate reward of one food pellet and another of four food pellets at a delay of 3, 6, 12 or 24s. In the case of the longer delays, SHR rats chose the immediate reward of lower magnitude more often than did their Wistar counterparts, and also committed a greater number of omissions during the forced-choice trials of the procedure. The results indicate that differences in schedule-induced polydipsia are related to indexes of cognitive rather than motor impulsivity, a finding in line with the theoretical idea that adjunctive behaviour is linked to operant reinforcement processes. Copyright © 2011 Elsevier B.V. All rights reserved.

Detection of metanil yellow contamination in turmeric using FT-Raman and FT-IR spectroscopy

NASA Astrophysics Data System (ADS)

Dhakal, Sagar; Chao, Kuanglin; Qin, Jianwei; Kim, Moon; Schmidt, Walter; Chan, Dian

2016-05-01

Turmeric is well known for its medicinal value and is often used in Asian cuisine. Economically motivated contamination of turmeric by chemicals such as metanil yellow has been repeatedly reported. Although traditional technologies can detect such contaminants in food, high operational costs and operational complexities have limited their use to the laboratory. This study used Fourier Transform Raman Spectroscopy (FT-Raman) and Fourier Transform - Infrared Spectroscopy (FT-IR) to identify metanil yellow contamination in turmeric powder. Mixtures of metanil yellow in turmeric were prepared at concentrations of 30%, 25%, 20%, 15%, 10%, 5%, 1% and 0.01% (w/w). The FT-Raman and FT-IR spectral signal of pure turmeric powder, pure metanil yellow powder and the 8 sample mixtures were obtained and analyzed independently to identify metanil yellow contamination in turmeric. The results show that FT-Raman spectroscopy and FT-IR spectroscopy can detect metanil yellow mixed with turmeric at concentrations as low as 1% and 5%, respectively, and may be useful for non-destructive detection of adulterated turmeric powder.

East Cameron Block 270, offshore Louisiana: a Pleistocene field

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holland, D.S.; Sutley, C.E.; Berlitz, R.E.

1976-01-01

Exploration of the Plio-Pleistocene in the Gulf of Mexico since 1970 has led to the discovery of significant hydrocarbon reserves. One of the better gas fields found to date has been the East Cameron Block 270 field, offshore Louisiana. Utilization of a coordinated exploitation plan with Schlumberger Offshore Services has allowed Pennzoil Co., as operator, to develop and put the Block 270 field on production in minimum time. The structure at Block 270 field is a north-south-trending, faulted nose at 6000 ft (1825 m). At the depth of the ''G'' sandstone (8700 ft or 2650 m), the structure is closed;more » it is elongated north-south and dips in all directions from the Block 270 area. Closure is the result of contemporaneous growth of the east-bounding regional fault. Structural and stratigraphic interpretations from dipmeters were used to determine the most favorable offset locations. The producing zones consist of various combinations of bar-like, channel-like, and distributary-front sandstones. The sediment source for most of the producing zones was southwest of the area, except for two zones which derived their sediments from the north through a system of channels paralleling the east-bounding fault. Computed logs were used to convert conventional logging measurements into a more readily usable form for evaluation. The computed results were used for reserve calculations, reservoir-quality determinations, and confirmation of depositional environments as determined from other sources.« less

Seepage investigation on selected reaches of Fish Creek, Teton County, Wyoming, 2004

USGS Publications Warehouse

Wheeler, Jerrod D.; Eddy-Miller, Cheryl A.

2005-01-01

A seepage investigation was conducted on Fish Creek, a tributary to the Snake River in Teton County in western Wyoming, near Wilson. Mainstem, return flow, tributary, spring, and diversion sites were selected and measured on six reaches along Fish Creek. Flow was measured under two flow regimes, high flow in August 2004 and base flow in November 2004. During August 17-19, 2004, 20 sites had quantifiable discharge with median values ranging from 0.93 to 384 ft3/s for the 14 mainstem sites on Fish Creek, and from 0.35 to 12.2 ft3/s for the 5 return, spring, and tributary sites (inflows). The discharge was 2.23 ft3/s for the single diversion site (outflow). Estimated gains or losses from ground water were calculated for all reaches using the median discharge values and the estimated measurement errors. Reach 1 had a calculated gain in discharge from ground water (23.8 ?3.3 ft3/s). Reaches 2-6 had no calculated gains in flow, greater than the estimated error, that could be attributed to ground water. A second set of measurements were made under base-flow conditions during November 3-4, 2004. Twelve of the 20 sites visited in August 2004 were flowing and were measured. All of the Reach 1 sites near Teton Village were dry. Median discharge values ranged from 10.3 to 70.0 ft3/s on the nine Fish Creek mainstem sites, and from 2.32 to 3.71 ft3/s on the three return, spring, and tributary sites (inflows). Reaches 2, 3 and 6 had a gain from ground water. Reaches 4 and 5 had no calculated gains in flow, greater than the estimated error, that could be attributed to ground water.

Spectroscopic (FT-IR, FT-Raman, UV and NMR) investigation and NLO, HOMO-LUMO, NBO analysis of organic 2,4,5-trichloroaniline.

PubMed

Govindarajan, M; Karabacak, M; Periandy, S; Tanuja, D

2012-11-01

In this work, the experimental and theoretical study on the molecular structure and vibrational spectra of 2,4,5-trichloroaniline (C(6)H(4)NCl(3), abbreviated as 2,4,5-TClA) were studied. The FT-IR and FT-Raman spectra were recorded. The molecular geometry and vibrational frequencies in the ground state were calculated by using the Hartree-Fock (HF) and density functional theory (DFT) methods (B3LYP) with 6-311++G(d,p) basis set. Comparison of the observed fundamental vibrational frequencies of 2,4,5-TClA with calculated results by HF and DFT indicates that B3LYP is superior to HF method for molecular vibrational problems. The difference between the observed and scaled wavenumber values of most of the fundamentals is very small. The theoretically predicted FT-IR and FT-Raman spectra of the title molecule have been constructed. A study on the electronic properties, such as HOMO and LUMO energies, were performed by time-dependent DFT (TD-DFT) approach. Besides, molecular electrostatic potential (MEP) and thermodynamic properties were performed. The electric dipole moment (μ) and the first hyperpolarizability (β) values of the investigated molecule were computed using ab initio quantum mechanical calculations. The calculated results also show that the 2,4,5-TClA molecule may have microscopic nonlinear optical (NLO) behavior with non-zero values. Mulliken atomic charges of 2,4,5-TClA was calculated and compared with aniline and chlorobenzene molecules. The (13)C nuclear magnetic resonance (NMR) chemical shifts of the molecule were calculated by the gauge independent atomic orbital (GIAO) method and compared with experimental results. Copyright © 2012 Elsevier B.V. All rights reserved.

Synthesis of sericin-based conjugates by click chemistry: enhancement of sunitinib bioavailability and cell membrane permeation.

PubMed

Scrivano, Luca; Iacopetta, Domenico; Sinicropi, Maria Stefania; Saturnino, Carmela; Longo, Pasquale; Parisi, Ortensia Ilaria; Puoci, Francesco

2017-11-01

Sericin is a natural protein that has been used in biomedical and pharmaceutical fields as raw material for polypeptide-based drug delivery systems (DDSs). In this paper, it has been employed as pharmaceutical biopolymer for the production of sunitinib-polypeptide conjugate. The synthesis has been carried out by simple click reaction in water, using the redox couple l-ascorbic acid/hydrogen peroxide as a free radical grafting initiator. The bioconjugate molecular weight (50 kDa < Mw < 75 kDa) was obtained by SDS-PAGE, while the spectroscopic characteristics have been studied in order to reveal the presence of grafted sunitinib. In both FT-IR and UV/Vis spectra, signals corresponding to sunitinib functional groups have been identified. Since sunitinib is an anticancer drug characterized by low bioavailability and low permeability, the bioconjugation aimed at their enhancement. In vitro studies demonstrated that bioavailability has been increased to almost 74%, compared with commercial formulation. Also cell membrane permeability has been augmented in in vitro tests, in which membrane models have been used to determine the lipid membrane/physiological fluid partition coefficient (Kp). The log(Kp) value of the bioconjugate was increased to over 4. This effect resulted in a three-fold decrease of IC 50 value against MCF-7 cells.

Evaluation of Turmeric Powder Adulterated with Metanil Yellow Using FT-Raman and FT-IR Spectroscopy

PubMed Central

Dhakal, Sagar; Chao, Kuanglin; Schmidt, Walter; Qin, Jianwei; Kim, Moon; Chan, Diane

2016-01-01

Turmeric powder (Curcuma longa L.) is valued both for its medicinal properties and for its popular culinary use, such as being a component in curry powder. Due to its high demand in international trade, turmeric powder has been subject to economically driven, hazardous chemical adulteration. This study utilized Fourier Transform-Raman (FT-Raman) and Fourier Transform-Infra Red (FT-IR) spectroscopy as separate but complementary methods for detecting metanil yellow adulteration of turmeric powder. Sample mixtures of turmeric powder and metanil yellow were prepared at concentrations of 30%, 25%, 20%, 15%, 10%, 5%, 1%, and 0.01% (w/w). FT-Raman and FT-IR spectra were acquired for these mixture samples as well as for pure samples of turmeric powder and metanil yellow. Spectral analysis showed that the FT-IR method in this study could detect the metanil yellow at the 5% concentration, while the FT-Raman method appeared to be more sensitive and could detect the metanil yellow at the 1% concentration. Relationships between metanil yellow spectral peak intensities and metanil yellow concentration were established using representative peaks at FT-Raman 1406 cm−1 and FT-IR 1140 cm−1 with correlation coefficients of 0.93 and 0.95, respectively. PMID:28231130

Geological studies of the COST GE-1 well, United States South Atlantic outer continental shelf area

USGS Publications Warehouse

Scholle, Peter A.

1979-01-01

The COST No. GE-1 well is the first deep stratigraphic test to be drilled in the southern part of the U.S. Atlantic Outer Continental Shelf (AOCS) area. The well was drilled within the Southeast Georgia Embayment to a total depth of 13,254 ft (4,040 m). It penetrated a section composed largely of chalky limestones to a depth of about 3,300 ft (1,000 m) below the drill platform. Limestones and calcareous shales with some dolomite predominate between 3,300 and 7,200 ft (1,000 and 2,200 m), whereas interbedded sandstones and shales are dominant from 7,200 to 11,000 ft (2,200 to 3,350 m). From 11,000 ft (3,350 m) to the bottom, the section consists of highly indurated to weakly metamorphosed pelitic sedimentary rocks and meta-igneous flows or intrusives. Biostratigraphic examination has shown that the section down to approximately 3,500 ft (1,060 m) is Tertiary, the interval from 3,500 to 5,900 ft (1,060 to 1,800 m) is Upper Cretaceous, and the section from 5,900 to 11,000 ft (1,800 to 3,350 m) is apparently Lower Cretaceous. The indurated to weakly metamorphosed section below 11,000 ft (3,350 m) is barren of fauna or flora but is presumed to be Paleozoic based on radiometric age determinations. Rocks deposited at upper-slope water depths were encountered in the Upper Cretaceous, Oligocene, and Miocene parts of the section. All other units were deposited in outer-shelf to terrestrial environments. Examination of cores, well cuttings, and electric logs shows that potential hydrocarbon-reservoir units are present within the chalks in the uppermost part of the section as well as in sandstone beds to a depth of at least 10,000 ft (3,000 m). Sandstones below that depth, and the metamorphic section between 11,000 and 13.250 ft (3,350 and 4,040 m) have extremely low permeabilities and are unlikely to contain potential reservoir rock. Studies of organic geochemistry, vitrinite reflectance, and color alteration of visible organic matter indicate that the chalk section down to approximately 3,600 ft (1,100 m) contains low concentrations of indigenous hydrocarbons, is thermally immature, and has a very poor source-rock potential. The interval from 3,600 to 5,900 ft (1,100 to 1,800 m) has a high content of marine organic matter but appears to be thermally immature. Where buried more deeply, this interval may have significant potential as an oil source. The section from 5,900 to 8,850 ft (1,800 to 2,700 m) has geochemical characteristics indicative of a poor oil source rock and is thermally immature. Rocks below this depth, although they may be marginally to fully mature, are virtually barren of organic matter and thus have little or no source-rock potential. Therefore, despite the thermal immaturity of the overall section, the uppor half of the sedimentary section penetrated in the well shows the greatest petroleum source potential.

Impact of temperature, pH, and salinity changes on the physico-chemical properties of model naphthenic acids.

PubMed

Celsie, Alena; Parnis, J Mark; Mackay, Donald

2016-03-01

The effects of temperature, pH, and salinity change on naphthenic acids (NAs) present in oil-sands process wastewater were modeled for 55 representative NAs. COSMO-RS was used to estimate octanol-water (KOW) and octanol-air (KOA) partition ratios and Henry's law constants (H). Validation with experimental carboxylic acid data yielded log KOW and log H RMS errors of 0.45 and 0.55 respectively. Calculations of log KOW, (or log D, for pH-dependence), log KOA and log H (or log HD, for pH-dependence) were made for model NAs between -20 °C and 40 °C, pH between 0 and 14, and salinity between 0 and 3 g NaCl L(-1). Temperature increase by 60 °C resulted in 3-5 log unit increase in H and a similar magnitude decrease in KOA. pH increase above the NA pKa resulted in a dramatic decrease in both log D and log HD. Salinity increase over the 0-3 g NaCl L(-1) range resulted in a 0.3 log unit increase on average for KOW and H values. Log KOW values of the sodium salt and anion of the conjugate base were also estimated to examine their potential for contribution to the overall partitioning of NAs. Sodium salts and anions of naphthenic acids are predicted to have on average 4 log units and 6 log units lower log KOW values, respectively, with respect to the corresponding neutral NA. Partitioning properties are profoundly influenced by the by the relative prevailing pH and the substance's pKa at the relevant temperature. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mitotane treatment in patients with adrenocortical cancer causes central hypothyroidism.

PubMed

Russo, Marco; Scollo, Claudia; Pellegriti, Gabriella; Cotta, Oana Ruxandra; Squatrito, Sebastiano; Frasca, Francesco; Cannavò, Salvatore; Gullo, Damiano

2016-04-01

Mitotane, a steroidogenesis inhibitor with adrenolytic properties used to treat adrenocortical cancer (ACC), can affect thyroid function. A reduction of FT4 levels with normal FT3 and TSH has been described in these patients. Using an in vitro murine model, the secretory capacity of thyrotrophic cells has been shown to be inhibited by mitotane. To investigate the pathogenesis of thyroid abnormalities in mitotane-treated patients with ACC. In five female patients with ACC (median age 47; range 31-65) treated with mitotane (dosage 1·5 g/day; 1·0-3·0), we analysed the pattern of TSH and thyroid function index (FT4, FT3 and FT3/FT4 ratio) compared to an age- and gender-matched control group. The in vivo secretory activity of the thyrotrophic cells was evaluated using a standard TRH test (200 μg), and the response was compared to both a group of age-matched female controls (n = 10) and central hypothyroid patients (n = 10). Basal TSH (median 1·54 mU/l; range 1·20-2·17) was normal and scattered around our median reference value, FT3 levels (median 3·80 pmol/l; 3·30-4·29) were normal but below the median reference value of 4·37 pmol/l and FT4 levels were below the normal range in all patients (median 8·40 pmol/l; 7·6-9·9). FT3/FT4 ratio was in the upper range in 4 patients and higher than normal in one patient. A blunted TSH response to TRH was observed in mitotane-treated patients. ΔTSH (absolute TSH response, peak TSH minus basal TSH) was 3·65 (range 3·53-5·26), 12·37 (range 7·55-19·97) and 1·32 mU/l (range 0·52-4·66) in mitotane-treated patients, controls and central hypothyroid patients, respectively. PRL secretion was normal. Mitotane-treated patients with ACC showed low FT4, normal FT3 and TSH and impaired TSH response to TRH, characteristic of central hypothyroidism. Furthermore, the elevated FT3/FT4 ratio of these subjects reflects an enhanced T4 to T3 conversion rate, a compensatory mechanism characteristic of thyroid function changes observed in hypothyroid conditions. This finding thus confirms in vitro studies and may have a therapeutic implication for treatment with thyroid hormones, as suggested by current guidelines for this specific condition. © 2015 John Wiley & Sons Ltd.

Determination of the distribution coefficient (log Kd) of oxytetracycline, tylosin A, olaquindox and metronidazole in manure.

PubMed

Loke, Marie-Louise; Tjørnelund, Jette; Halling-Sørensen, Bent

2002-07-01

Olaquindox (log Kow = -2.3) and metronidazole (log Kow = -0.1) both have low tendencies to sorp to particles in manure. This corresponds with the negative log Kow values of these antibiotics. Tylosin (log Kow = 1.63) and oxytetracycline (log Kow = -1.12) sorp relatively strongly to the manure particles and have log Kd values between 1.5 and 2.0. The tendency to bind to manure was ranked after increasing binding as follows: metronidazole < olaquindox < tylosin A and oxytetracycline. This order of ranking is consistent with results of sorption in soil. Our experiments illustrate that for some antibacterial agents estimation of the partitioning coefficients, Kd, cannot be made from Kow and f(oc) alone. Sorption of oxytetracycline to manure is much higher than expected from the negative log Kow value of the compound. It is believed that sorption of oxytetracycline to manure is influenced by ionic binding to divalent metal ions as such Mg2+ and Ca2+ as well as other charged compounds in the matrix. Binding of oxytetracycline to soil is stronger than the binding to manure. This is most likely due to the strong mineral related metal complexes formed between soil, metal ion and oxytetracycline. These complexes are not known to exist in manure. The relatively strong sorption of tylosin A to manure corresponds with data found for soil sorption of tylosin. Tylosin has a log Kow value of 2.5, thus it is not surprising that this drug binds strongly to manure.

Experimental (13C NMR, 1H NMR, FT-IR, single-crystal X-ray diffraction) and DFT studies on 3,4-bis(isoproylamino)cyclobut-3-ene-1,2-dione.

PubMed

Süleymanoğlu, Nevin; Ustabaş, Reşat; Alpaslan, Yelda Bingöl; Eyduran, Fatih; Ozyürek, Cengiz; Iskeleli, Nazan Ocak

2011-12-01

In this work, 3,4-bis(isoproylamino)cyclobut-3-ene-1,2-dione C(10)H(16)N(2)O(2) (I), was synthesized and characterized by (13)C NMR, (1)H NMR, FT-IR, UV-vis spectroscopy and single-crystal X-ray diffraction. DFT method with 6-31G(d,p) basis set has been used to calculate the optimized geometrical parameters, atomic charges, vibrational frequencies and chemical shift values. The calculated vibrational frequencies and chemical shift values are compared with experimental FT-IR and NMR spectra. The results of the calculation shows good agreement between experimental and calculated values of the compound I. The existence of N-H⋯O type intermolecular ve C-H⋯O type intramolecular hydrogen bonds can be deduced from differences between experimental and calculated results of FT-IR and NMR. In addition, the molecular electrostatic potential map and frontier molecular orbitals and electronic absorption spectra were performed at B3LYP/6-31G(d,p) level of theory. HOMO-LUMO electronic transition of 4.90 eV are derived from the contribution of the bands π→π* and n→π* The spectral results obtained from FT-IR, NMR and X-ray of I revealed that the compound I is in predominantly enamine tautomeric form, which was supported by DFT calculations. Copyright © 2011 Elsevier B.V. All rights reserved.

An evaluation of the 10:30 centerline marking pattern.

DOT National Transportation Integrated Search

1977-01-01

In response to Value Engineering Proposal #M-26, a study of the feasibility of adopting a 10 ft. mark 30 ft. gap centerline pattern for use on 2- and 4-lane rural roads was conducted. The study included a literature review, field studies of traffic s...

Coal Rank and Stratigraphy of Pennsylvanian Coal and Coaly Shale Samples, Young County, North-Central Texas

USGS Publications Warehouse

Guevara, Edgar H.; Breton, Caroline; Hackley, Paul C.

2007-01-01

Vitrinite reflectance measurements were made to determine the rank of selected subsurface coal and coaly shale samples from Young County, north-central Texas, for the National Coal Resources Database System State Cooperative Program conducted by the Bureau of Economic Geology at The University of Texas at Austin. This research is the continuation of a pilot study that began in adjacent Archer County, and forms part of a larger investigation of the coalbed methane resource potential of Pennsylvanian coals in north-central Texas. A total of 57 samples of coal and coaly shale fragments were hand-picked from drill cuttings from depths of about 2,000 ft in five wells, and Ro determinations were made on an initial 10-sample subset. Electric-log correlation of the sampled wells indicates that the collected samples represent coal and coaly shale layers in the Strawn (Pennsylvanian), Canyon (Pennsylvanian), and Cisco (Pennsylvanian-Permian) Groups. Coal rank in the initial sample subset ranges from lignite (Ro=0.39), in a sample from the Cisco Group at a depth of 310 to 320 ft, to high volatile bituminous A coal (Ro=0.91) in a sample from the lower part of the Canyon Group at a depth of 2,030 to 2,040 ft.

Properties of an entropy-based signal receiver with an application to ultrasonic molecular imaging.

PubMed

Hughes, M S; McCarthy, J E; Marsh, J N; Arbeit, J M; Neumann, R G; Fuhrhop, R W; Wallace, K D; Znidersic, D R; Maurizi, B N; Baldwin, S L; Lanza, G M; Wickline, S A

2007-06-01

Qualitative and quantitative properties of the finite part, H(f), of the Shannon entropy of a continuous waveform f(t) in the continuum limit are derived in order to illuminate its use for waveform characterization. Simple upper and lower bounds on H(f), based on features of f(t), are defined. Quantitative criteria for a priori estimation of the average-case variation of H(f) and log E(f), where E(f) is the signal energy of f(t) are also derived. These provide relative sensitivity estimates that could be used to prospectively choose optimal imaging strategies in real-time ultrasonic imaging machines, where system bandwidth is often pushed to its limits. To demonstrate the utility of these sensitivity relations for this application, a study designed to assess the feasibility of identification of angiogenic neovasculature targeted with perfluorocarbon nanoparticles that specifically bind to alpha(v)beta3-integrin expression in tumors was performed. The outcome of this study agrees with the prospective sensitivity estimates that were used for the two receivers. Moreover, these data demonstrate the ability of entropy-based signal receivers when used in conjunction with targeted nanoparticles to elucidate the presence of alpha(v)beta3 integrins in primordial neovasculature, particularly in acoustically unfavorable environments.

A Systematic Review of Financial Toxicity Among Cancer Survivors: We Can't Pay the Co-Pay.

PubMed

Gordon, Louisa G; Merollini, Katharina M D; Lowe, Anthony; Chan, Raymond J

2017-06-01

To determine the extent of financial toxicity (FT) among cancer survivors, identify the determinants and how FT is measured. A systematic review was performed in MEDLINE, CINAHL and PsycINFO, using relevant terminology and included articles published from 1 January, 2013 to 30 June, 2016. We included observational studies where the primary outcomes included FT and study samples were greater than 200. The Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines were followed. From 417 citations, a total of 25 studies were included in this review. Seventy outcomes of FT were reported with 47 covering monetary, objective and subjective indicators of FT. A total of 28-48% of patients reported FT using monetary measures and 16-73% using subjective measures. The most commonly reported factors associated with FT were: being female, younger age, low income at baseline, adjuvant therapies and more recent diagnosis. Relative to non-cancer comparison groups, cancer survivors experienced significantly higher FT. Most studies were cross-sectional and causal inferences between FT and determinants were not possible. Measures of FT were varied and most were not validated, while monetary values of out-of-pocket expenses included different cost components across studies. A substantial proportion of cancer survivors experience financial hardship irrespective of how it is measured. Using standardised outcomes and longitudinal designs to measure FT would improve determination of the extent of FT. Further research is recommended on reduced work participation and income losses occurring concurrently with FT and on the impacts on treatment non-adherence.

Accurately determining log and bark volumes of saw logs using high-resolution laser scan data

Treesearch

R. Edward Thomas; Neal D. Bennett

2014-01-01

Accurately determining the volume of logs and bark is crucial to estimating the total expected value recovery from a log. Knowing the correct size and volume of a log helps to determine which processing method, if any, should be used on a given log. However, applying volume estimation methods consistently can be difficult. Errors in log measurement and oddly shaped...

Temperature dependence of Henry's law constants and KOA for simple and heteroatom-substituted PAHs by COSMO-RS

NASA Astrophysics Data System (ADS)

Parnis, J. Mark; Mackay, Donald; Harner, Tom

2015-06-01

Henry's Law constants (H) and octanol-air partition coefficients (KOA) for polycyclic aromatic hydrocarbons (PAHs) and selected nitrogen-, oxygen- and sulfur-containing derivatives have been computed using the COSMO-RS method between -5 and 40 °C in 5 °C intervals. The accuracy of the estimation was assessed by comparison of COSMOtherm values with published experimental temperature-dependence data for these and similar PAHs. COSMOtherm log H estimates with temperature-variation for parent PAHs are shown to have a root-mean-square (RMS) error of 0.38 (PAH), based on available validation data. Estimates of O-, N- and S-substituted derivative log H values are found to have RMS errors of 0.30 at 25 °C. Log KOA estimates with temperature variation from COSMOtherm are shown to be strongly correlated with experimental values for a small set of unsubstituted PAHs, but with a systematic underestimation and associated RMS error of 1.11. Similar RMS error of 1.64 was found for COSMO-RS estimates of a group of critically-evaluated log KOA values at room temperature. Validation demonstrates that COSMOtherm estimates of H and KOA are of sufficient accuracy to be used for property screening and preliminary environmental risk assessment, and perform very well for modeling the influence of temperature on partitioning behavior in the temperature range -5 to 40 °C. Temperature-dependent shifts of up to 2 log units in log H and one log unit for log KOA are predicted for PAH species over the range -5 and 40 °C. Within the family of PAH molecules, COSMO-RS is sufficiently accurate to make it useful as a source of estimates for modeling purposes, following corrections for systematic underestimation of KOA. Average changes in the values for log H and log KOA upon substitution are given for various PAH substituent categories, with the most significant shifts being associated with the ionizing nitro functionality and keto groups.

CREW Escape Capsule Retrorocket Concept. Volume 2. Selection of a Retrorocket System

DTIC Science & Technology

1977-05-01

Unlimited. 17 DISTRIUTION ST ATEMENT (or h & afiertct entered In Block 20 it different from Repor ) e IS SUPPLEMENTARY NOTES 19 K(EY WOrlDS (Continue -r...c.& UNCLASSIFIED SECUR TN CLASSIFICATION OF THIS PAGE(Wrin Veta Entered) 20. combination with recovery system descent rates of 30 through 60 ft/sec...thrusts are calculated by equation 1. A value of ignition height error E = ±0.5 ft or 2 JEL = 1.0 ft was selected as a design goal based on previous

Fishing tool retrieves MWD nuclear source from deep well

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

A new wire line tool has successfully retrieved the nuclear sources and formation data from a measurement-while-drilling (MWD) tool stuck in a deep, highly deviated well in the Gulf of Mexico. On Nov. 8, 1993, Schlumberger Wireline and Testing and Anadrill ran a logging-while-drilling inductive coupling (LINC) tool on conventional wire line to fish the gamma ray and neutron sources from a compensated density neutron (CDN) tool stuck in a well at 19,855 ft with an inclination greater than 80[degree]. The paper briefly describes the operation and equipment.

Current Direction and Velocity Measurements Using GPS Receivers Mounted on Floats at Tom Bevill Lock and Dam

DTIC Science & Technology

2002-12-01

radio and batteries. The procedures outlined in this CHETN will concentrate on the Magellan GPS ProMARK X-CP receiver as it was used to collect...The Magellan GPS ProMARK X-CP is a small robust light receiver that can log 9 hr of both pseudorange and carrier phase satellite data for post...post- processing software, pseudorange GPS data recorded by the ProMARK X-CP can be post-processed differential to achieve 1-3 m (3.3-9.8 ft) horizontal

The mobile Sousy-Doppler radar: Technical design and first results

NASA Technical Reports Server (NTRS)

Czechowsky, P.; Schmidt, G.; Ruster, R.

1983-01-01

A mobile VHF Doppler system was developed. The electronic part is installed in a 20 ft container and tested using a special log periodic aerial to illuminate the 300 m dish. The system was extended by designing a mobile phased antenna array with finally 576 Yagi elements. The grouping of the single Yagis, the system of transmission lines, the phase shifters, the power splitters and the T/R switch are described. Results from the first two campaigns and a survey of future programs demonstrating the flexibility of this mobile system are summarized.

Dual control of pituitary thyroid stimulating hormone secretion by thyroxine and triiodothyronine in athyreotic patients

PubMed Central

Hoermann, Rudolf; Midgley, John E. M.; Dietrich, Johannes W.; Larisch, Rolf

2017-01-01

Background: Patient responses to levothyroxine (LT4) monotherapy vary considerably. We sought to differentiate contributions of FT4 and FT3 in controlling pituitary thyroid stimulating hormone (TSH) secretion. Methods: We retrospectively assessed the relationships between TSH and thyroid hormones in 319 patients with thyroid carcinoma through 2914 visits on various LT4 doses during follow-up for 5.5 years (median, IQR 4.2, 6.9). We also associated patient complaints with the relationships. Results: Under varying dose requirements (median 1.84 µg/kg, IQR 1.62, 2.11), patients reached TSH targets below 0.4, 0.1 or 0.01 mIU/l at 73%, 54% and 27% of visits. While intercept, slope and fit of linearity of the relationships between lnTSH and FT4/FT3 varied between individuals, gender, age, LT4 dose and deiodinase activity influenced the relationships in the cohort (all p < 0.001). Deiodinase activity impaired by LT4 dose significantly affected the lnTSH–FT4 relationship. Dose increase and reduced conversion efficiency displaced FT3–TSH equilibria. In LT4-treated patients, FT4 and FT3 contributed on average 52% versus 38%, and by interaction 10% towards TSH suppression. Symptomatic presentations (11%) accompanied reduced FT3 concentrations (–0.23 pmol/l, p = 0.001) adjusted for gender, age and BMI, their relationships being shifted towards higher TSH values at comparable FT3/FT4 levels. Conclusions: Variation in deiodinase activity and resulting FT3 levels shape the TSH–FT4 relationship in LT4-treated athyreotic patients, suggesting cascade control of pituitary TSH production by the two hormones. Consequently, measurement of FT3 and calculation of conversion efficiency may identify patients with impaired biochemistry and a resulting lack of symptomatic control. PMID:28794850

Detection of metanil yellow contamination in turmeric using FT-Raman and FT-IR spectroscopy

USDA-ARS?s Scientific Manuscript database

Turmeric is well known for its medicinal value and is often used in Asian cuisine. Economically motivated contamination of turmeric by chemicals such as metanil yellow has been repeatedly reported. Although traditional technologies can detect such contaminants in food, high operational costs and ope...

Degraded lands worth protecting: the biological importance of Southeast Asia's repeatedly logged forests

PubMed Central

Edwards, David P.; Larsen, Trond H.; Docherty, Teegan D. S.; Ansell, Felicity A.; Hsu, Wayne W.; Derhé, Mia A.; Hamer, Keith C.; Wilcove, David S.

2011-01-01

Southeast Asia is a hotspot of imperilled biodiversity, owing to extensive logging and forest conversion to oil palm agriculture. The degraded forests that remain after multiple rounds of intensive logging are often assumed to be of little conservation value; consequently, there has been no concerted effort to prevent them from being converted to oil palm. However, no study has quantified the biodiversity of repeatedly logged forests. We compare the species richness and composition of birds and dung beetles within unlogged (primary), once-logged and twice-logged forests in Sabah, Borneo. Logging had little effect on the overall richness of birds. Dung beetle richness declined following once-logging but did not decline further after twice-logging. The species composition of bird and dung beetle communities was altered, particularly after the second logging rotation, but globally imperilled bird species (IUCN Red List) did not decline further after twice-logging. Remarkably, over 75 per cent of bird and dung beetle species found in unlogged forest persisted within twice-logged forest. Although twice-logged forests have less biological value than primary and once-logged forests, they clearly provide important habitat for numerous bird and dung beetle species. Preventing these degraded forests from being converted to oil palm should be a priority of policy-makers and conservationists. PMID:20685713

Automated potentiometric titrations in KCl/water-saturated octanol: method for quantifying factors influencing ion-pair partitioning.

PubMed

Scherrer, Robert A; Donovan, Stephen F

2009-04-01

The knowledge base of factors influencing ion pair partitioning is very sparse, primarily because of the difficulty in determining accurate log P(I) values of desirable low molecular weight (MW) reference compounds. We have developed a potentiometric titration procedure in KCl/water-saturated octanol that provides a link to log P(I) through the thermodynamic cycle of ionization and partitioning. These titrations have the advantage of being independent of the magnitude of log P, while maintaining a reproducibility of a few hundredths of a log P in the calculated difference between log P neutral and log P ion pair (diff (log P(N - I))). Simple model compounds can be used. The titration procedure is described in detail, along with a program for calculating pK(a)'' values incorporating the ionization of water in octanol. Hydrogen bonding and steric factors have a greater influence on ion pairs than they do on neutral species, yet these factors are missing from current programs used to calculate log P(I) and log D. In contrast to the common assumption that diff (log P(N - I)) is the same for all amines, they can actually vary more than 3 log units, as in our examples. A major factor affecting log P(I) is the ability of water and the counterion to approach the charge center. Bulky substituents near the charge center have a negative influence on log P(I). On the other hand, hydrogen bonding groups near the charge center have the opposite effect by lowering the free energy of the ion pair. The use of this titration method to determine substituent ion pair stabilization values (IPS) should bring about more accurate log D calculations and encourage species-specific QSAR involving log D(N) and log D(I). This work also brings attention to the fascinating world of nature's highly stabilized ion pairs.

Automated Potentiometric Titrations in KCl/Water-Saturated Octanol: Method for Quantifying Factors Influencing Ion-Pair Partitioning

PubMed Central

2009-01-01

The knowledge base of factors influencing ion pair partitioning is very sparse, primarily because of the difficulty in determining accurate log PI values of desirable low molecular weight (MW) reference compounds. We have developed a potentiometric titration procedure in KCl/water-saturated octanol that provides a link to log PI through the thermodynamic cycle of ionization and partitioning. These titrations have the advantage of being independent of the magnitude of log P, while maintaining a reproducibility of a few hundredths of a log P in the calculated difference between log P neutral and log P ion pair (diff (log PN − I)). Simple model compounds can be used. The titration procedure is described in detail, along with a program for calculating pKa′′ values incorporating the ionization of water in octanol. Hydrogen bonding and steric factors have a greater influence on ion pairs than they do on neutral species, yet these factors are missing from current programs used to calculate log PI and log D. In contrast to the common assumption that diff (log PN − I) is the same for all amines, they can actually vary more than 3 log units, as in our examples. A major factor affecting log PI is the ability of water and the counterion to approach the charge center. Bulky substituents near the charge center have a negative influence on log PI. On the other hand, hydrogen bonding groups near the charge center have the opposite effect by lowering the free energy of the ion pair. The use of this titration method to determine substituent ion pair stabilization values (IPS) should bring about more accurate log D calculations and encourage species-specific QSAR involving log DN and log DI. This work also brings attention to the fascinating world of nature’s highly stabilized ion pairs. PMID:19265385

Molecular structure, spectroscopic studies and first-order molecular hyperpolarizabilities of ferulic acid by density functional study

NASA Astrophysics Data System (ADS)

Sebastian, S.; Sundaraganesan, N.; Manoharan, S.

2009-10-01

Quantum chemical calculations of energies, geometrical structure and vibrational wavenumbers of ferulic acid (FA) (4-hydroxy-3-methoxycinnamic acid) were carried out by using density functional (DFT/B3LYP/BLYP) method with 6-31G(d,p) as basis set. The optimized geometrical parameters obtained by DFT calculations are in good agreement with single crystal XRD data. The vibrational spectral data obtained from solid phase FT-IR and FT-Raman spectra are assigned based on the results of the theoretical calculations. The observed spectra are found to be in good agreement with calculated values. The electric dipole moment ( μ) and the first hyperpolarizability ( β) values of the investigated molecule have been computed using ab initio quantum mechanical calculations. The calculation results also show that the FA molecule might have microscopic nonlinear optical (NLO) behavior with non-zero values. A detailed interpretation of the infrared and Raman spectra of FA was also reported. The energy and oscillator strength calculated by time-dependent density functional theory (TD-DFT) results complements with the experimental findings. The calculated HOMO and LUMO energies shows that charge transfer occur within the molecule. The theoretical FT-IR and FT-Raman spectra for the title molecule have been constructed.

Both hypothyroidism and hyperthyroidism increase plasma irisin levels in rats.

PubMed

Atici, Emine; Mogulkoc, Rasim; Baltaci, Abdulkerim Kasim; Menevse, Esma

2017-11-28

Background A recently discovered hormone, irisin is accepted to be significantly involved in the regulation of body weight. Thyroid functions may be, directly or indirectly, associated with irisin. Aim The aim of the present study is to determine the effect of experimental thyroid dysfunction on irisin levels in rats. Methods The study registered 40 adult male Sprague-Dawley rats, which were allocated to groups as follows: 1. Control; 2. Hypothyroidism induced by injection of 10 mg/kg/day intraperitoneal propylthiouracil (PTU) for 3 weeks; 3. Hypothyroidism (PTU 2 weeks) + L-thyroxin (1.5 mg/kg/day for 1 week); 4. Hyperthyroidism induced in rats by 3-week thyroxin (0.3 mg/kg/day); 5. Hyperthyroidism + PTU. At the end of the study, blood samples were collected to quantify free triiodothyronine (FT3), free triiodothyronine (FT4) and irisin levels. Results FT3 and FT4 levels were reduced in hypothyroidism and were significantly elevated in hyperthyroidism (p < 0.001). Irisin values, on the other hand, were found to be elevated in both hypothyroidism and hyperthyroidism groups (p < 0.001). Conclusion The results of the study suggest that irisin values increase in thyroid dysfunction, hypo- and hyperthyroidism, and that when hypothyroidism is corrected by thyroxin administration and hyperthyroidism by PTU injection, plasma irisin values go back to normal.

High-precision branching ratio measurement for the superallowed β+ emitter Ga62

NASA Astrophysics Data System (ADS)

Finlay, P.; Ball, G. C.; Leslie, J. R.; Svensson, C. E.; Towner, I. S.; Austin, R. A. E.; Bandyopadhyay, D.; Chaffey, A.; Chakrawarthy, R. S.; Garrett, P. E.; Grinyer, G. F.; Hackman, G.; Hyland, B.; Kanungo, R.; Leach, K. G.; Mattoon, C. M.; Morton, A. C.; Pearson, C. J.; Phillips, A. A.; Ressler, J. J.; Sarazin, F.; Savajols, H.; Schumaker, M. A.; Wong, J.

2008-08-01

A high-precision branching ratio measurement for the superallowed β+ decay of Ga62 was performed at the Isotope Separator and Accelerator (ISAC) radioactive ion beam facility. The 8π spectrometer, an array of 20 high-purity germanium detectors, was employed to detect the γ rays emitted following Gamow-Teller and nonanalog Fermi β+ decays of Ga62, and the SCEPTAR plastic scintillator array was used to detect the emitted β particles. Thirty γ rays were identified following Ga62 decay, establishing the superallowed branching ratio to be 99.858(8)%. Combined with the world-average half-life and a recent high-precision Q-value measurement for Ga62, this branching ratio yields an ft value of 3074.3±1.1 s, making Ga62 among the most precisely determined superallowed ft values. Comparison between the superallowed ft value determined in this work and the world-average corrected F tmacr value allows the large nuclear-structure-dependent correction for Ga62 decay to be experimentally determined from the CVC hypothesis to better than 7% of its own value, the most precise experimental determination for any superallowed emitter. These results provide a benchmark for the refinement of the theoretical description of isospin-symmetry breaking in A⩾62 superallowed decays.

The modelling of carbon-based supercapacitors: Distributions of time constants and Pascal Equivalent Circuits

NASA Astrophysics Data System (ADS)

Fletcher, Stephen; Kirkpatrick, Iain; Dring, Roderick; Puttock, Robert; Thring, Rob; Howroyd, Simon

2017-03-01

Supercapacitors are an emerging technology with applications in pulse power, motive power, and energy storage. However, their carbon electrodes show a variety of non-ideal behaviours that have so far eluded explanation. These include Voltage Decay after charging, Voltage Rebound after discharging, and Dispersed Kinetics at long times. In the present work, we establish that a vertical ladder network of RC components can reproduce all these puzzling phenomena. Both software and hardware realizations of the network are described. In general, porous carbon electrodes contain random distributions of resistance R and capacitance C, with a wider spread of log R values than log C values. To understand what this implies, a simplified model is developed in which log R is treated as a Gaussian random variable while log C is treated as a constant. From this model, a new family of equivalent circuits is developed in which the continuous distribution of log R values is replaced by a discrete set of log R values drawn from a geometric series. We call these Pascal Equivalent Circuits. Their behaviour is shown to resemble closely that of real supercapacitors. The results confirm that distributions of RC time constants dominate the behaviour of real supercapacitors.

Effects of chain length, chlorination degree, and structure on the octanol-water partition coefficients of polychlorinated n-alkanes.

PubMed

Hilger, Bettina; Fromme, Hermann; Völkel, Wolfgang; Coelhan, Mehmet

2011-04-01

Log octanol-water partition coefficients (log Kow) of 40 synthesized polychlorinated n-alkanes (PCAs) with different chlorination degrees were determined using reversed-phase high performance liquid chromatography (RP-HPLC). In addition, log Kow values of a technical mixture namely Cereclor 63L as well as 15 individual in house synthesized C10, C11, and C12 chloroalkanes with known chlorine positions were estimated. Based on these results, the effects of chain length, chlorination degree, and structure were explored. The estimated log Kow values ranged from 4.10 (polychlorinated n-decanes with 50.2% chlorine content) to 11.34 (polychlorinated n-octacosanes with 54.8% chlorine content) for PCAs and from 3.82 (1,2,5,6,9,10-hexachlorodecane) to 7.75 (1,1,1,3,9,11,11,11-octachlorododecane) for the individual chloroalkanes studied. The results showed that log Kow value was influenced linearly at a given chlorine content by chain length, while a polynominal effect was observed in dependence on the chlorination degree of an alkane chain. Chlorine substitution pattern influenced markedly the log Kow value of chloroalkanes.

Sustainable management of harbours : a numerical approach for the assessment of waters quality

NASA Astrophysics Data System (ADS)

Bonamano, Simone; Madonia, Alice; Piazzolla, Daniele; Paladini de Mendoza, Francesco; Piermattei, Viviana; Scanu, Sergio; Melchiorri, Cristiano; Marcelli, Marco

2017-04-01

Within the Water Framework Directive (WFD), harbours must reach or maintain the good ecological potential, being classified as heavily modified water bodies. To fulfill this task and to comply the Marine Spatial Planning (MSP) principles, port managers have to monitor the water quality that can be compromised by the numerous activities including the realization of new infrastructures. The port of Civitavecchia, located on the central west coast of Italy, is undergoing to major structural changes to become one of the first ports of the Mediterranean in terms of passenger traffic and goods, thus requiring the development of management tools for the predictive assessment of harbour water quality. This study focused on the evaluation of water degradation within Civitavecchia port trough the calculation of Flushing time (FT) and the development of the new Flushing Efficiency Index (FEI). FT was calculated through the use of a numerical model under different scenarios selected combining different weather conditions with the new port configurations. FT values was then used to estimate the FEI for the evaluation of the improvement (positive values) or the deterioration (negative values) of water quality in the different zones of the port. The increase in the harbour basin size due to the embankment extension results in high values of FT, particularly in the inner part of the port, in accordance with the highest values of the Enrichment Factor (EF) of the trace metals found in the sediment. The correlation between FT and EF confirms that renewal time can be used as a proxy to evaluate the water quality conditions in the harbour basin, as also stated by the WFD guidelines. Also the results of FEI calculation indicate the potential occurrence of water degradation due to the embankment extension. Otherwise, the realization of a second entrance in the southern part of Civitavecchia port produces FEI positive values, highlighting a drastic improvement in harbour water renewal. Consistent with Blue Growth and Bluemed initiatives, the new tools developed in this study support the sustainable management of port activities, thereby also contributing to the development of new "blue jobs."

Value recovery from two mechanized bucking operations in the southeastern United States

Treesearch

Kevin Boston; Glen. Murphy

2003-01-01

The value recovered from two mechanized bucking operations in the southeastern United States was compared with the optimal value computed using an individual-stem log optimization program, AVIS. The first operation recovered 94% of the optimal value. The main cause for the value loss was a failure to capture potential sawlog volume; logs were bucked to a larger average...

U.S. Geological Survey research in Handcart Gulch, Colorado—An alpine watershed with natural acid-rock drainage

USGS Publications Warehouse

Manning, Andrew H.; Caine, Jonathan S.; Verplanck, Philip L.; Bove, Dana J.; Kahn, Katherine G.

2009-01-01

Handcart Gulch is an alpine watershed along the Continental Divide in the Colorado Rocky Mountain Front Range. It contains an unmined mineral deposit typical of many hydrothermal mineral deposits in the intermountain west, composed primarily of pyrite with trace metals including copper and molybdenum. Springs and the trunk stream have a natural pH value of 3 to 4. The U.S. Geological Survey began integrated research activities at the site in 2003 with the objective of better understanding geologic, geochemical, and hydrologic controls on naturally occurring acid-rock drainage in alpine watersheds. Characterizing the role of groundwater was of particular interest because mountain watersheds containing metallic mineral deposits are often underlain by complexly deformed crystalline rocks in which groundwater flow is poorly understood. Site infrastructure currently includes 4 deep monitoring wells high in the watershed (300– 1,200 ft deep), 4 bedrock (100–170 ft deep) and 5 shallow (10–30 ft deep) monitoring wells along the trunk stream, a stream gage, and a meteorological station. Work to date at the site includes: geologic mapping and structural analysis; surface sample and drill core mineralogic characterization; geophysical borehole logging; aquifer testing; monitoring of groundwater hydraulic heads and streamflows; a stream tracer dilution study; repeated sampling of surface and groundwater for geochemical analyses, including major and trace elements, several isotopes, and groundwater age dating; and construction of groundwater flow models. The unique dataset collected at Handcart Gulch has yielded several important findings about bedrock groundwater flow at the site. Most importantly, we find that bedrock bulk permeability is nontrivial and that bedrock groundwater apparently constitutes a substantial fraction of the hydrologic budget. This means that bedrock groundwater commonly may be an underappreciated component of the hydrologic system in studies of alpine watersheds. Additionally, despite the complexity of the fracture controlled aquifer system, it appears that it can be represented with a relatively simple conceptual model and can be treated as an equivalent porous medium at the watershed scale. Interpretation of existing data, collection of new monitoring data, and efforts to link geochemical and hydrologic processes through modeling are ongoing at the site.

Highly Efficient Synthesis of Fructooligosaccharides by Extracellular Fructooligosaccharide-Producing Enzymes and Immobilized Cells of Aspergillus aculeatus M105 and Purification and Biochemical Characterization of a Fructosyltransferase from the Fungus.

PubMed

Huang, Mei-Ping; Wu, Min; Xu, Qiang-Sheng; Mo, De-Jiao; Feng, Jia-Xun

2016-08-24

In this work, Aspergillus aculeatus M105 was obtained to produce high extracellular fructooligosaccharide-producing enzyme activity. The maximum yields of fructooligosaccharides produced by its extracellular enzymes and immobilized cells were 67.54 and 65.47% (w/w), respectively. A fructosyltransferase (FTase), AaFT32A, was purified from M105. The optimal pH and temperature of AaFT32A were pH 5.0-6.0 and 65 °C, respectively. The Km, Vmax, and kcat values for the transfructosylating activity of AaFT32A were 2267 mM, 1347 μmol/min/mg protein, and 1550.2 s(-1), respectively, and those values for the hydrolytic activity of AaFT32A were 6.10 mM, 32.44 μmol/min/mg protein, and 37.3 s(-1), respectively. The sequence of AaFT32A deduced from the cloned gene shared 99.4% identity with a FTase from Aspergillus japonicus CB05 and a fructofuranosidase from Aspergillus niger and 96.5% identity with a FTase (Aspacl_37092) from A. aculeatus ATCC 16872. The fungal strain and its FTase may have potential applications in the prebiotics industry.

Application of nanofiltration for the removal of carbamazepine, diclofenac and ibuprofen from drinking water sources.

PubMed

Vergili, I

2013-09-30

Pharmaceutical active compounds (PhACs) are persistent during the process used to treat drinking water and, because drinking water treatment plants are not specifically designed to remove PhACs, these compounds are found in drinking water. Although there are currently no regulations or drinking water directives for PhACs, precautionary principles suggest ensuring maximal removal of PhACs through improved or existing treatment techniques. This study was designed to investigate the performance of a nanofiltration membrane in cross-flow filtration equipment for the removal of three PhACs [carbamazepine (CBZ), diclofenac (DIC) and ibuprofen (IBU)] that were spiked in water taken from a drinking water treatment plant using surface water. Because of their low solubilities, high log Kow values, low dipole moments and negative charges, higher rejection values were obtained for DIC and IBU. Low to moderate rejection values were most likely due to the small molecular sizes of the PhACs (i.e., MW < MWCO) and the divalent ions present in the raw water. Flux declines obtained from DIC studies was attributed to the adsorption of DIC ions inside the membrane pores, which decreases the flux. The most evident change in the FT-IR spectrum after nanofiltration was the appearance of new intense bands at 1072 cm(-1) and 1011 cm(-1), indicating the deposition of calcium salts on the membrane surface. Copyright © 2013 Elsevier Ltd. All rights reserved.

Synthesis of sulfadimethoxine based surfactants and their evaluation as antitumor agents.

PubMed

Khowdiary, Manal Mohmed; Mostafa, Nashwa S

2016-01-01

Synthesized CO (II) and Pt (II) of sulfadimethoxine. These compounds were tested for potential antitumor activity against two of human tumor cell lines, colon carcinoma cell line [Hct116], and breast carcinoma cell line MCF7. The structures of the resulting compounds have been investigated by elemental, FT-IR and H 1 NMR analyzes to insure the purity and confirmed the structures of them. The surface properties studies and octanol/water partition coefficients, Po/w were measured. The synthesized compounds exhibit biological activities with the lowest log Po/w and critical micelle concentration (CMC) values. In addition, in this article we provide an insight into this subject in order to increase the drug bioavailability. Inhibitory activity against colon carcinoma cells was detected for Pt and cobalt ion complex with IC50 = 4.5, 2.2 µg and against breast carcinoma cells IC50 = 18.2, 5.7 µg, respectively. The main goal of cancer therapy is to attain the maximum therapeutic damage of tumor cells in combination with a minimum concentration of the drug. This can be achieved in principle via selective antitumor preparations, the cytostatic effects of which would be restricted within tumor tissue. While 100% selectivity may be impractical, the achievement of reasonably high selectivity seems to be a feasible aim. Platinum and cobalt complex surfactants in our research affect tumor tissue at a very low concentration at values lower than their CMC values; this indicate that the sulfadimethoxine complexes merit further investigation as potential antitumor drugs.

Lithofacies control of lignite distribution and ground-water quality, Wilcox group (Eocene), east-central Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ayers, W.B. Jr.; Lewis, A.H.

1984-04-01

Deep lignite resources (200-2000 ft; 61-610 m) were evaluated regionally using 1470 geophysical well logs to interpret lithofacies, lignite occurrence, and resistivity (water quality). The regional distribution of lithofacies indicates that in the region, the Wilcox Group is a fluvial-deltaic system. The primary fluvial system entered the Wilcox coastal plain west of Waco, Texas, trended southeast, and supplied a 75-mi (120-km) wide fluvial-deltaic system comparable in size to the Mississippi system. Lignites are most abundant in the Calvert Bluff Formation (upper Wilcox). Lower Calvert Bluff lignites are thickest and most extensive southwest of the Navasota River, whereas those of themore » upper Calvert Bluff are thickest northeast of the Brazos River. In the shallow subsurface, Calvert Bluff lignites are found in dip-elongate low-sand areas (flood plains) between channel-sand belts. Basinward, laterally continuous lignites coincide with high net sand areas comprise of distributary channel sands indicative of a delta-plain setting. The wilcox Group is a major aquifer. Maps of resistivity values show that Wilcox channel sands are conduits for ground-water flow. High values of formation resistivity (low total dissolved solids) exist in recharge areas at outcrop and around salt domes. Elongate trends of high resistivity values extend tens of miles basinward and coincide with axes of major sands. Resistivity values decrease basinward and the 20 ohm-m contour delineates the downdip limit of fresh water. Lithofacies and lignite occurrence maps are guides to exploration for deep lignite. Resistivity maps can be used to explore for ground-water resources.« less

The conservation value of South East Asia's highly degraded forests: evidence from leaf-litter ants

PubMed Central

Woodcock, Paul; Edwards, David P.; Fayle, Tom M.; Newton, Rob J.; Khen, Chey Vun; Bottrell, Simon H.; Hamer, Keith C.

2011-01-01

South East Asia is widely regarded as a centre of threatened biodiversity owing to extensive logging and forest conversion to agriculture. In particular, forests degraded by repeated rounds of intensive logging are viewed as having little conservation value and are afforded meagre protection from conversion to oil palm. Here, we determine the biological value of such heavily degraded forests by comparing leaf-litter ant communities in unlogged (natural) and twice-logged forests in Sabah, Borneo. We accounted for impacts of logging on habitat heterogeneity by comparing species richness and composition at four nested spatial scales, and examining how species richness was partitioned across the landscape in each habitat. We found that twice-logged forest had fewer species occurrences, lower species richness at small spatial scales and altered species composition compared with natural forests. However, over 80 per cent of species found in unlogged forest were detected within twice-logged forest. Moreover, greater species turnover among sites in twice-logged forest resulted in identical species richness between habitats at the largest spatial scale. While two intensive logging cycles have negative impacts on ant communities, these degraded forests clearly provide important habitat for numerous species and preventing their conversion to oil palm and other crops should be a conservation priority. PMID:22006966

Distribution and Bioconcentration of Polycyclic Aromatic Hydrocarbons in Surface Water and Fishes

PubMed Central

Li, Haiyan; Ran, Yong

2012-01-01

To examine spatial distribution and bioconcentration of PAHs, water and fish samples were collected from Pearl River Delta in summer and spring, respectively. Particulate organic carbon, dissolved organic carbon, biodegradable DOC (BDOC), and chlorophyll a were measured. PAHs were dominated by 2- and 3-ring compounds in the water and SPM samples. Aqueous and solid-phase PAHs, respectively, showed significant correlations with total organic matter (TOC) in SPM or dissolved organic matter (DOC) in the water. The in-situ partitioning coefficients (logK oc, mL/g) for the samples were observed to be related to logK ow, implying that the hydrophobicity of PAHs is a critical factor in their distribution. It was also observed that BCF increased with the increasing K ow in the viscera of tilapia (logBCF = 0.507logK ow − 1.368, r = 0.883). However, most of the observed log BCF values in other different fish tissues at first increased with the increasing of log K ow, then reached a maximum value when logK ow is between 5 and 7, and then decreased when logK ow is higher than 7, indicating that the value of BCF may vary due to the diversity of fish species. PMID:23365526

Evaluation of turmeric powder adulterated with metanil yellow using FT-Raman and FT-IR spectroscopy

USDA-ARS?s Scientific Manuscript database

Turmeric powder (Curcuma longa L.) is valued both for its medicinal properties and for its popular culinary use such as being a component in curry powder. Due to its high demand in international trade, turmeric powder has been subject to economically driven, hazardous chemical adulteration. This stu...

Peroxidase-like activity of apoferritin paired gold clusters for glucose detection.

PubMed

Jiang, Xin; Sun, Cuiji; Guo, Yi; Nie, Guangjun; Xu, Li

2015-02-15

The discovery and application of noble metal nanoclusters have received considerable attention. In this paper, we reported that apoferritin paired gold clusters (Au-Ft) could efficiently catalyze oxidation of 3.3',5.5'-tetramethylbenzidine (TMB) by H2O2 to produce a blue color reaction. Compared with natural enzyme, Au-Ft exhibited higher activity near acidic pH and could be used over a wide range of temperatures. Apoferritin nanocage enhanced the reaction activity of substrate TMB by H2O2. The reaction catalyzed by Au-Ft was found to follow a typical Michaelis-Menten kinetics. The kinetic parameters exhibited a lower K(m) value (0.097 mM) and a higher K(cat) value (5.8 × 10(4) s(-1)) for TMB than that of horse radish peroxidase (HRP). Base on these findings, Au-Ft, acting as a peroxidase mimetic, performed enzymatic spectrophotometric analysis of glucose. This system exhibited acceptable reproducibility and high selectivity in biosening, suggesting that it could have promising applications in the future. Copyright © 2014 Elsevier B.V. All rights reserved.

Assay of free thyroxine and free triiodothyronine in fine-needle aspiration of thyroid nodules: a useful and low-cost assessment.

PubMed

Barbaro, Daniele; Macchia, Enrico; Orsini, Paola; Piazza, Francesca; Lapi, Paola; Pasquini, Cristina

2004-01-01

To evaluate whether analysis of thyroid hormones in fine-needle aspiration (FNA) of thyroid nodules can provide information about the functional status and the nature of the nodules. We studied 4 groups of patients: group 1, 17 patients with autonomous hyperfunctioning thyroid nodules; group 2, 52 patients with cold nonfunctioning thyroid nodules; group 3, 12 patients with malignant thyroid nodules; and group 4 (control group), 10 patients with nonthyroid nodular lesions (enlarged parathyroid glands or lymph nodes). The assay of thyroid hormones was performed in FNA after the washing of needles and, with patient consent, also in normal thyroid parenchyma. The free thyroxine (FT(4)) and free triiodothyronine (FT(3)) values were remarkably high in group 1 (mean, 5.5 +/- 0.53 ng/dL and 27.6 +/- 3.1 pg/mL, respectively; P<0.05 versus group 2 and group 4, the control group). The levels of FT(4) and FT(3) were very low in group 3 (<0.2 ng/dL and <1.0 pg/mL, respectively; P<0.05 versus group 2). Thyroglobulin values in FNA specimens were much higher than the normal range in human serum, but no significant differences were found between the various groups. The control group had low levels of FT(4) and FT(3) (<0.2 ng/dL and <1.0 pg/mL, respectively) in conjunction with low levels of thyroglobulin, whereas parathyroid hormone levels were high in parathyroid nodules. These results show that assay of FT(4) and FT(3) in FNA can yield information about the functional status of thyroid nodules and, indirectly, about the nature of nodules. In this era of sophisticated new molecular markers in FNA cytology, this low-cost diagnostic method can be readily performed in every laboratory.

High Precision Determination of the β Decay Q(EC) Value of (11)C and Implications on the Tests of the Standard Model.

PubMed

Gulyuz, K; Bollen, G; Brodeur, M; Bryce, R A; Cooper, K; Eibach, M; Izzo, C; Kwan, E; Manukyan, K; Morrissey, D J; Naviliat-Cuncic, O; Redshaw, M; Ringle, R; Sandler, R; Schwarz, S; Sumithrarachchi, C S; Valverde, A A; Villari, A C C

2016-01-08

We report the determination of the Q(EC) value of the mirror transition of (11)C by measuring the atomic masses of (11)C and (11)B using Penning trap mass spectrometry. More than an order of magnitude improvement in precision is achieved as compared to the 2012 Atomic Mass Evaluation (Ame2012) [Chin. Phys. C 36, 1603 (2012)]. This leads to a factor of 3 improvement in the calculated Ft value. Using the new value, Q(EC)=1981.690(61)  keV, the uncertainty on Ft is no longer dominated by the uncertainty on the Q(EC) value. Based on this measurement, we provide an updated estimate of the Gamow-Teller to Fermi mixing ratio and standard model values of the correlation coefficients.

Simulation of Groundwater Mounding Beneath Hypothetical Stormwater Infiltration Basins

USGS Publications Warehouse

Carleton, Glen B.

2010-01-01

Groundwater mounding occurs beneath stormwater management structures designed to infiltrate stormwater runoff. Concentrating recharge in a small area can cause groundwater mounding that affects the basements of nearby homes and other structures. Methods for quantitatively predicting the height and extent of groundwater mounding beneath and near stormwater Finite-difference groundwater-flow simulations of infiltration from hypothetical stormwater infiltration structures (which are typically constructed as basins or dry wells) were done for 10-acre and 1-acre developments. Aquifer and stormwater-runoff characteristics in the model were changed to determine which factors are most likely to have the greatest effect on simulating the maximum height and maximum extent of groundwater mounding. Aquifer characteristics that were changed include soil permeability, aquifer thickness, and specific yield. Stormwater-runoff variables that were changed include magnitude of design storm, percentage of impervious area, infiltration-structure depth (maximum depth of standing water), and infiltration-basin shape. Values used for all variables are representative of typical physical conditions and stormwater management designs in New Jersey but do not include all possible values. Results are considered to be a representative, but not all-inclusive, subset of likely results. Maximum heights of simulated groundwater mounds beneath stormwater infiltration structures are the most sensitive to (show the greatest change with changes to) soil permeability. The maximum height of the groundwater mound is higher when values of soil permeability, aquifer thickness, or specific yield are decreased or when basin depth is increased or the basin shape is square (and values of other variables are held constant). Changing soil permeability, aquifer thickness, specific yield, infiltration-structure depth, or infiltration-structure shape does not change the volume of water infiltrated, it changes the shape or height of the groundwater mound resulting from the infiltration. An aquifer with a greater soil permeability or aquifer thickness has an increased ability to transmit water away from the source of infiltration than aquifers with lower soil permeability; therefore, the maximum height of the groundwater mound will be lower, and the areal extent of mounding will be larger. The maximum height of groundwater mounding is higher when values of design storm magnitude or percentage of impervious cover (from which runoff is captured) are increased (and other variables are held constant) because the total volume of water to be infiltrated is larger. The larger the volume of infiltrated water the higher the head required to move that water away from the source of recharge if the physical characteristics of the aquifer are unchanged. The areal extent of groundwater mounding increases when soil permeability, aquifer thickness, design-storm magnitude, or percentage of impervious cover are increased (and values of other variables are held constant). For 10-acre sites, the maximum heights of the simulated groundwater mound range from 0.1 to 18.5 feet (ft). The median of the maximum-height distribution from 576 simulations is 1.8 ft. The maximum areal extent (measured from the edge of the infiltration basins) of groundwater mounding of 0.25-ft ranges from 0 to 300 ft with a median of 51 ft for 576 simulations. Stormwater infiltration at a 1-acre development was simulated, incorporating the assumption that the hypothetical infiltration structure would be a pre-cast concrete dry well having side openings and an open bottom. The maximum heights of the simulated groundwater-mounds range from 0.01 to 14.0 ft. The median of the maximum-height distribution from 432 simulations is 1.0 ft. The maximum areal extent of groundwater mounding of 0.25-ft ranges from 0 to 100 ft with a median of 10 ft for 432 simulations. Simulated height and extent of groundwater mounding associ

Refraction and visual acuity in a national Danish cohort of 4-year-old children of extremely preterm delivery.

PubMed

Fledelius, Hans C; Bangsgaard, Regitze; Slidsborg, Carina; laCour, Morten

2015-06-01

A recent threefold increase in laser treatment for advanced retinopathy of prematurity (ROP) triggered a nationwide preschool ophthalmic and developmental status among extremely preterm survivors. Here, we discuss refraction and visual acuity. Survivors (n = 178) from a national birth cohort (February 2004 to March 2006) of gestational age <28 weeks (PT) and 56 full-term (FT) controls attended for evaluation at age 4 years. Cycloplegic refraction and keratometry were achieved by Retinomax autokeratorefractor and visual acuities by symbol recognition (HOTV, logMAR). The refractive distribution presented a myopic tail (4.5%) and a hyperopic tail (11.9% ≥+2.5 D) as special preterm features, and corneas were more curved. Astigmatism and anisometropia were only marginally increased, and visual acuities were generally good. Best-corrected binocular median logMAR visual acuity was 0.1 in FT and 0.2 in PT, in Snellen equivalents 0.8 and 0.63. Snellen acuity ≤0.5 occurred across the ROP subgroups, but mainly in those with at least ROP stage 3. Two children had low vision. The overall fair outcome for refraction and function is in accordance with other recent northern Europe experience. The results differ in particular from the poorer ophthalmic outcomes reported in the pioneer US treatment studies (cryotherapy for ROP and ETROP). The diode laser ablations (n = 32) appeared effective in our series; except one child, all treated subjects had good or fair social vision at the age of 4 years. © 2015 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Preliminary physical stratigraphy, biostratigraphy, and geophysical data of the USGS South Dover Bridge Core, Talbot County, Maryland

USGS Publications Warehouse

Alemán González, Wilma B.; Powars, David S.; Seefelt, Ellen L.; Edwards, Lucy E.; Self-Trail, Jean M.; Durand, Colleen T.; Schultz, Arthur P.; McLaughlin, Peter P.

2012-01-01

The South Dover Bridge (SDB) corehole was drilled in October 2007 in Talbot County, Maryland. The main purpose for drilling this corehole was to characterize the Upper Cretaceous and Paleogene lithostratigraphy and biostratigraphy of the aquifers and confining units of this region. The data obtained from this core also will be used as a guide to geologic mapping and to help interpret well data from the eastern part of the Washington East 1:100,000-scale map near the town of Easton, Md. Core drilling was conducted to a depth of 700 feet (ft). The Cretaceous section was not penetrated due to technical problems during drilling. This project was funded by the U.S. Geological Survey’s (USGS) Eastern Geology and Paleoclimate Science Center (EGPSC) as part of the Geology of the Atlantic Watersheds Project; this project was carried out in cooperation with the Maryland Geological Survey (MGS) through partnerships with the Aquifer Characterization Program of the USGS’s Maryland-Delaware-District of Columbia Water Science Center and the National Cooperative Geologic Mapping Program. The SDB corehole was drilled by the USGS drilling crew in the northeastern corner of the Trappe 7.5-minute quadrangle, near the type locality of the Boston Cliffs member of the Choptank Formation. Geophysical logs (gamma ray, single point resistance, and 16-inch and 64-inch normal resistivity) were run to a depth of 527.5 ft; the total depth of 700.0 ft could not be reached because of the collapse of the lower part of the hole. Of the 700.0 ft drilled, 531.8 ft of core were recovered, representing a 76 percent core recovery. The elevation of the top of the corehole is approximately 12 ft above mean sea level; its coordinates are lat 38°44′49.34″N. and long 76°00′25.09″W. (38.74704N., 76.00697W. in decimal degrees). A groundwater monitoring well was not installed at this site. The South Dover Bridge corehole was the first corehole that will be used to better understand the geology and hydrology of the Maryland Eastern Shore.

Individual stem value recovery of modified and conventional tree-length systems in the southeastern United States

Treesearch

Amanda H. Lang; Shawn A. Baker; W. Dale Greene; Glen E. Murphy

2010-01-01

We compared value recovery of a modified treelength (MTL) logging system that measures product diameter and length using a Waratah 626 harvester head to that of a treelength (TL) system that estimates dimensions. A field test compared the actual value cut to the maximum potential value suggested by the log bucking optimization program Assessment of Value by Individual...

Assessment of subjective intraocular forward scattering and quality of vision after posterior chamber phakic intraocular lens with a central hole (Hole ICL) implantation.

PubMed

Iijima, Ayaka; Shimizu, Kimiya; Yamagishi, Mayumi; Kobashi, Hidenaga; Igarashi, Akihito; Kamiya, Kazutaka

2016-12-01

To evaluate the subjective intraocular forward scattering and quality of vision after posterior chamber phakic intraocular lens with a central hole (Hole ICL, STAAR Surgical) implantation. We prospectively examined 29 eyes of 29 consecutive patients (15 men and 14 women; ages, 37.2 ± 8.8 years) undergoing Hole ICL implantation. We assessed the values of the logarithmic straylight value [log (s)] using a straylight meter (C-Quant ™ , Oculus) preoperatively and 3 months postoperatively. The patients completed a questionnaire detailing symptoms on a quantitative grading scale (National Eye Institute Refractive Error Quality of Life Instrument-42; NEI RQL-42) 3 months postoperatively. We compared the preoperative and postoperative values of the log(s) and evaluated the correlation of these values with patient subjective symptoms. The mean log(s) was not significantly changed, from 1.07 ± 0.20 preoperatively, to 1.06 ± 0.17 postoperatively (Wilcoxon signed-rank test, p = 0.641). There was a significant correlation between the preoperative and postoperative log(s) (Spearman's correlation coefficient r = 0.695, p < 0.001). The postoperative log(s) was significantly associated with the scores of glare in the questionnaire (Spearman's correlation coefficient r = -0.575, p = 0.017). According to our experience, Hole ICL implantation does not induce a significant additional change in the subjective intraocular forward scattering. The symptom of glare after Hole ICL implantation was significantly correlated with the postoperative intraocular forward scattering in relation to the preoperative one. © 2016 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Preliminary evaluation of the shale gas prospectivity of the Lower Cretaceous Pearsall Formation in the onshore Gulf Coast region, United States

USGS Publications Warehouse

Enomoto, Catherine B.; Scott, Kristina; Valentine, Brett J.; Hackley, Paul C.; Dennen, Kristin; Lohr, Celeste D.

2012-01-01

Recent work by the U.S. Geological Survey indicated that the Lower Cretaceous Pearsall Formation contains an estimated mean undiscovered, technically recoverable unconventional gas resource of 8.8 trillion cubic ft in the Maverick Basin, South Texas. Cumulative gas production from horizontal wells in the core area of the emerging play has exceeded 5 billion cubic ft since 2008. However, very little information is available to characterize the Pearsall Formation as an unconventional gas resource beyond the Maverick Basin in the greater Gulf Coast region. Therefore, this reconnaissance study examines spatial distribution, thickness, organic richness and thermal maturity of the Pearsall Formation in the onshore U.S. Gulf states using wireline logs and drill cuttings sample analysis. Spontaneous potential and resistivity curves of approximately forty wireline logs from wells in five Gulf Coast states were correlated to ascertain the thickness of the Pearsall Formation and delineate its three members: Pine Island Shale, James Limestone or Cow Creek Limestone, and Bexar Shale, in ascending stratigraphic order. In Florida and Alabama the Pearsall Formation is up to about 300 ft thick; in Mississippi, Louisiana, Arkansas, and East Texas, thickness is up to as much as 800 ft. Drill cuttings sampled from 11 wells at depths ranging from 4600 to 19,600 feet subsurface indicate increasingly oxygenated depositional environments (predominance of red shale) towards the eastern part of the basin. Cuttings vary widely in lithology but indicate interbedded clastics and limestones throughout the Pearsall Formation, consistent with previous regional studies. Organic petrographic and geochemical analyses of 17 cutting samples in the Pearsall Formation indicate a wide range in thermal maturity, from immature (0.43% Ro [vitrinite reflectance]) in paleo-high structural locations to the peak oil window (0.99% Ro) in the eastern portion of the Gulf Coast Basin. This is in contrast to dry gas thermal maturity throughout the Pearsall Formation in the South Texas Maverick Basin. Organic carbon content is low overall, even in immature samples, with a range of 0.17 to 1.08 wt.% by Leco in 22 Pearsall Formation samples. The pyrolysis output range was 0.23 to 2.33 mg hydrocarbon/g rock. The thermal maturity and Rock-Eval pyrolysis data and organic petrologic observations from this study will be used to better focus specific areas of investigation where the Pearsall Formation may be prospective as an unconventional hydrocarbon source and reservoir.

The Value of Web Log Data in Use-based Design and Testing.

ERIC Educational Resources Information Center

Burton, Mary C.; Walther, Joseph B.

2001-01-01

Suggests Web-based logs contain useful empirical data with which World Wide Web designers and design theorists can assess usability and effectiveness of design choices. Enumerates identification of types of Web server logs, client logs, types and uses of log data, and issues associated with the validity of these data. Presents an approach to…

Transient hyperthyroidism after surgery for secondary hyperparathyroidism: a common problem.

PubMed

Rudofsky, Gottfried; Tsioga, M; Reismann, P; Leowardi, C; Kopf, S; Grafe, I A; Nawroth, P P; Isermann, B

2011-08-08

Postoperative hyperthyroidism occurs in approximately one third of patients following parathyroidectomy due to primary hyperparathyroidism (PHP), but has only rarely been described in secondary hyperparathyroidism (SHP). The frequency, course, and laboratory markers of postoperative hyperthyroidism in SHP remain unknown. Our purpose was to evaluate the frequency and the clinical course of postoperative hyperthyroidism following surgery of SHP and to determine the diagnostic value of thyroglobulin in this setting. A total of 40 patients undergoing parathyroidectomy because of SHP were included in this study. Thyroid stimulating hormone (TSH), free triiodothyronine (fT3), free thyroxine (fT4), and thyroglobulin (Tg) were determined one day before and on day 1, 3, 5, 10, and 40 after surgery. At each of these visits patients were clinically evaluated for signs or symptoms of hyperthyroidism. Biochemical evidence of hyperthyroidism was evident in 77% of patients postoperatively despite of preoperatively normal serum levels. TSH dropped from 1.18 ± 0.06mU/L to 0.15 ± 0.07mU/L (p = 0.0015). Free triiodothyronine (fT3) and fT4 levels increased from 2.86 ± 0.02ng/L and 10.32 ± 0.13ng/L, respectively, to their maximum of 4.83 ± 0.17ng/L and 19.35 ± 0.58ng/L, respectively. Thyroglobulin levels rose from 3.8 ± 0.8ng/mL to 111.8 ± 45.3ng/mL (p<0.001). At day 40 all thyroid related laboratory values were within normal range. Correlation analysis of postoperative values revealed significant correlations for lowest TSH (r = -0.32; p = 0.038), and highest fT3 (r = 0.55; p<0.001) and fT4 levels (r = 0.67; p<0.001) with Tg. Transient hyperthyroidism is frequent after parathyroidectomy for SHP with Tg being a suitable marker. Awareness of this self-limiting disorder is important to avoid inappropriate and potentially harmful treatment.

Constraining the age and magnitude of uplift in the northern National Petroleum Reserve in Alaska (NPRA)-apatite fission-track analysis of samples from three wells

USGS Publications Warehouse

Houseknecht, David W.; Bird, Kenneth J.; O'Sullivan, Paul

2011-01-01

A broad, post-mid-Cretaceous uplift is defined in the northern National Petroleum Reserve in Alaska (NPRA) by regional truncation of Cretaceous strata, thermal maturity patterns, and amounts of exhumation estimated from sonic logs. Apatite fission-track (AFT) analysis of samples from three wells (South Meade No. 1, Topagoruk No. 1, and Ikpikpuk No. 1) across the eastern flank of the uplift indicates Tertiary cooling followed by Quaternary heating. Results from all three wells indicate that cooling, presumably caused by uplift and erosion, started about 75-65 Ma (latest Cretaceous-earliest Tertiary) and continued through the Tertiary Period. Data from South Meade indicate more rapid cooling after about 35-15 Ma (latest Eocene-middle Miocene) followed by a significant increase in subsurface temperature during the Quaternary, probably the result of increased heat flow. Data from Topagoruk and Ikpikpuk include subtle evidence of accelerated cooling starting in the latest Eocene-middle Miocene and possible evidence of increased temperature during the Quaternary. Subsurface temperature perturbations related to the insulating effect of permafrost may have been responsible for the Quaternary temperature increase at Topagoruk and Ikpikpuk and may have been a contributing factor at South Meade. Multiple lines of geologic evidence suggest that the magnitude of exhumation resulting from uplift and erosion is 5,000-6,500 ft at South Meade, 4,000-5,500 ft at Topagoruk, and 2,500-4,000 ft at Ikpikpuk. The results from these wells help to define the broad geometry of the uplift, which increases in magnitude from less than 1,000 ft at the Colville River delta to perhaps more than 7,000 ft along the northwestern coast of NPRA, between Point Barrow and Peard Bay. Neither the origin nor the offshore extent of the uplift, west and north of the NPRA coast, have been determined.

Separate-channel analysis of two-channel microarrays: recovering inter-spot information.

PubMed

Smyth, Gordon K; Altman, Naomi S

2013-05-26

Two-channel (or two-color) microarrays are cost-effective platforms for comparative analysis of gene expression. They are traditionally analysed in terms of the log-ratios (M-values) of the two channel intensities at each spot, but this analysis does not use all the information available in the separate channel observations. Mixed models have been proposed to analyse intensities from the two channels as separate observations, but such models can be complex to use and the gain in efficiency over the log-ratio analysis is difficult to quantify. Mixed models yield test statistics for the null distributions can be specified only approximately, and some approaches do not borrow strength between genes. This article reformulates the mixed model to clarify the relationship with the traditional log-ratio analysis, to facilitate information borrowing between genes, and to obtain an exact distributional theory for the resulting test statistics. The mixed model is transformed to operate on the M-values and A-values (average log-expression for each spot) instead of on the log-expression values. The log-ratio analysis is shown to ignore information contained in the A-values. The relative efficiency of the log-ratio analysis is shown to depend on the size of the intraspot correlation. A new separate channel analysis method is proposed that assumes a constant intra-spot correlation coefficient across all genes. This approach permits the mixed model to be transformed into an ordinary linear model, allowing the data analysis to use a well-understood empirical Bayes analysis pipeline for linear modeling of microarray data. This yields statistically powerful test statistics that have an exact distributional theory. The log-ratio, mixed model and common correlation methods are compared using three case studies. The results show that separate channel analyses that borrow strength between genes are more powerful than log-ratio analyses. The common correlation analysis is the most powerful of all. The common correlation method proposed in this article for separate-channel analysis of two-channel microarray data is no more difficult to apply in practice than the traditional log-ratio analysis. It provides an intuitive and powerful means to conduct analyses and make comparisons that might otherwise not be possible.

Exposure to Lithium and Cesium Through Drinking Water and Thyroid Function During Pregnancy: A Prospective Cohort Study

PubMed Central

Harari, Florencia; Bottai, Matteo; Casimiro, Esperanza; Palm, Brita

2015-01-01

Background: Impaired thyroid function is a common side effect of lithium medication. Recent data indicate that lithium exposure through drinking water, although providing much lower doses than the medication, may also affect thyroid hormone levels. However, the effects in susceptible groups like pregnant women are not known. Methods: In a population-based mother–child cohort in the Argentinean Andes (n = 194), an area with varying concentrations of lithium in the drinking water, we assessed lithium exposure repeatedly during pregnancy by measuring the concentrations in blood using inductively coupled plasma mass spectrometry. The markers of thyroid function included thyrotropin (TSH), free/total thyroxine (fT4/T4), free/total triiodothyronine (fT3/T3), thyroglobulin, and transthyretin in serum, sampled at the same time. Multiple potential confounders, including exposure to arsenic, cesium, and boron (elevated in water) as well as selenium and iodine (essential for thyroid function) were considered. Results: The lithium concentrations in blood [median 25 μg/L (0.0036 mmol/L); range 1.9–145 μg/L (0.000027–0.021 mmol/L)] correlated significantly with those in urine and drinking water (rs = 0.84, p < 0.001, and rs = 0.40, p < 0.001, respectively). Using linear quantile regression models, we found a positive association between blood lithium (log2 transformed) and TSH concentrations, particularly in the lowest percentiles of TSH (B = 0.20 mIU/L, [95% confidence interval 0.048–0.35] at the fifth percentile). We also found inverse associations of blood lithium with transthyretin, particularly at the highest percentiles, as well as with fT3 and T3, with less obvious variation across percentiles. Unexpectedly, blood cesium concentrations (median 111 μg/L, range 2.5–711 μg/L) were also inversely associated with fT3 and T3, particularly at the highest T3 percentiles, but not with TSH or transthyretin. Arsenic and boron exposure (also through drinking water) did not show any associations with the thyroid parameters. Conclusions: The study supports previous findings that lithium exposure through drinking water may impair thyroid function. The results regarding cesium exposure through drinking water are new. During pregnancy, impaired thyroid function may be detrimental for fetal development. The findings reinforce the need for better control of drinking water, including bottled water, as well as a health-based guideline value. PMID:26332132

Application of a continuous distribution model for proton binding by humic acids extracted from acidic lake sediments

NASA Astrophysics Data System (ADS)

Rhea, James R.; Young, Thomas C.

1987-10-01

The proton binding characteristics of humic acids extracted from the sediments of Cranberry Pond, an acidic water body located in the Adirondack Mountain region of New York State, were explored by the application of a multiligand distribution model. The model characterizes a class of proton binding sites by mean log K values and the standard deviations of log K values about the mean. Mean log K values and their relative abundances were determined directly from experimental titration data. The model accurately predicts the binding of protons by the humic acids for pH values in the range 3.5 to 10.0.

Application of a continuous distribution model for proton binding by humic acids extracted from acidic lake sediments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rhea, J.R.; Young, T.C.

1987-01-01

The proton binding characteristics of humic acids extracted from the sediments of Cranberry Pond, an acidic water body located in the Adirondack Mountain region of New York State, were explored by the application of a nultiligand distribution model. The model characterizes a class of proton binding sites by mean log K values and the standard deviations of log K values and the mean. Mean log K values and their relative abundances were determined directly from experimental titration data. The model accurately predicts the binding of protons by the humic acids for pH values in the range 3.5 to 10.0.

Acute toxicity and antispasmodic activities of Achillea wilhelmsii C. Koch.

PubMed

Ali, Niaz; Shah, Syed Wadood Ali; Ahmed, Ghayour; Shah, Ismail; Shoaib, Mohammad; Junaid, Muhammad; Ali, Waqar

2014-03-01

Since Achillea wilhelmsii is used as antispasmodic in traditional medicine, we conducted our current work to investigate its rationale on scientific grounds. Acute toxicity studies of crude methanol extract of Achillea wilhelmsii (Aw. CMeOH) is also performed. Effect of Aw. CMeOH and its fractions were tested on isolated sections of rabbits' jejunum at test concentrations 0.01, 0.03, 1.0, 3.0, 5.0 and 10mg/ml. The test extracts, in similar concentrations, were also tested on KCl-induced contractions. Calcium chloride curves were constructed for those fractions which relaxed KCl induced contractions in the absence and presence of the test samples to investigate its possible mode of action through calcium channels. Aw. CMeOH tested positive for flavonoids, saponins, tannins, glycosides, terpenoids, sterols, phenols, carbohydrates and proteins. LD(50) for acute toxicity studies is 2707±12.6 mg/kg. Mean EC(50) values for Aw. CMeOH on spontaneous and KCl-induced contractions are 3.41±0.18 (2.56-3.8, n=6) and 0.68±0.05 (0.6-0.85, n=6) mg/ml, respectively. Respective EC(50) values for n-hexane fraction on spontaneous and KCl-induced contractions are 3.06±0.08 (2.8-3.3, n=6) and 1.68±0.8 (1.4-1.9, n=6) mg/ml, respectively. Corresponding EC(50) (mg/ml) values for chloroformic, ethylacetate and aqueous fractions of Achillea wilhelmsii on spontaneous rabbits' jejunum preparations are 4.8±0.2 (4.41-5.63, n=6), 5.07±0.15 (4.7-5.58, n=6) and 5.2±0.13 (4.91-5.64, n=4), respectively. Constructing calcium chloride curves, in the presence of 0.1 mg/ml of Aw. CMeOH, mean EC(50) value (log molar [Ca(++)]) is-1.98±0.03 (-1.89-2.05, n=6) vs. control EC(50) (log molar [Ca(++)])-2.41±0.02 (-2.32-2.44, n=6). Mean EC(50) value (log molar [Ca(++)]) for 0.3 mg/ml n-hexane fraction is-1.76±0.05 (-1.70 -1.93, n=6) vs. control EC(50) (log molar [Ca(++)]) value-2.18±0.07 (-2.0-2.46, n=6). While in the presence of chloroformic fraction (3 mg/ml), mean EC(50) (log molar [Ca(++)]) value is -2.4±0.1 (-2.78 -2.9, n=6) vs. control EC(50) (log molar [Ca(++)]) value-2.70±0.05 (-2.5-2.8, n=6). Mean EC(50) value (log molar [Ca(++)]) for ethyl acetate fraction (1 mg/ml) is-1.94±0.07 (-1.75-2.05, n=6) vs. control EC(50) (log molar [Ca(++)]) value-2.69±0.04 (-2.57-2.79, n=6). Mean EC(50) (log molar [Ca(++)]) value for residual aqueous fraction (3 mg/ml) is-1.8±0.3 (-1.71-1.84, n=6) vs. control EC(50) (log molar [Ca(++)]) -2.6±0.04 (-2.59-2.76, n=6). Whereas, the verapamil (0.1µM) EC(50) value (log molar [Ca(++)]) is-1.7±0.1 (-1.6-1.8, n=6) vs. control EC(50) value (log molar [Ca(++)])- 2.4±0.09 (-2.3-2.47, n=6). The present research work confirms that the intestinal relaxation effect of Achillea wilhelmsii is supporting its traditional use as antispasmodic. The plant species can be a source for calcium antagonist(s), which can preferably be isolated from n-hexane fraction.

Establishing the cut off values of androgen markers in the assessment of polycystic ovarian syndrome.

PubMed

Nadaraja, R N D; Sthaneshwar, P; Razali, N

2018-04-01

Hyperandrogenism remains as one of the key features in Polycystic Ovarian Syndrome (PCOS) and can be assessed clinically or determined by biochemical assays. Hirsutism is the most common clinical manifestation of hyperandrogenism. The clinical assessment is subjected to wide variability due to poor interobserver agreement and multiple population factors such as ethnic variation, cosmetic procedures and genetic trait. The difficulty in resolving the androgen excess biochemically is due to a lack of consensus as to which serum androgen should be measured for the diagnosis of PCOS. The aim of the study was to compare and establish the diagnostic cut off value for different androgen biomarker for the diagnosis of PCOS. A total of 312 patients classified to PCOS (n = 164) and non PCOS (n = 148) cohorts were selected from the Laboratory Information System (LIS) based on serum total testosterone (TT) and sex hormone binding globulin (SHBG) from the period of 1st April 2015 to 31st March 2016. PCOS was diagnosed based on Rotterdam criteria. Clinical hyperandrogenism and ultrasound polycystic ovarian morphology were obtained from the clinical records. The other relevant biochemical results such as serum luteinizing hormone (LH), follicle stimulating hormone (FSH) and albumin were also obtained from LIS. Free androgen index (FAI), calculated free testosterone (cFT) and calculated bioavailable testosterone (cBT) were calculated for these patients. Receiver Operating Characteristic (ROC) curve analysis were performed for serum TT, SHBG, FAI, cFT, cBT and LH: FSH ratio to determine the best marker to diagnose PCOS. All the androgen parameters (except SHBG) were significantly higher in PCOS patients than in control (p<0.0001). The highest area under curve (AUC) curve was found for cBT followed by cFT and FAI. TT and LH: FSH ratio recorded a lower AUC and the lowest AUC was seen for SHBG. cBT at a cut off value of 0.86 nmol/L had the highest specificity, 83% and positive likelihood ratio (LR) at 3.79. This is followed by FAI at a cut off value of 7.1% with specificity at 82% and cFT at a cut off value of 0.8 pmol/L with specificity at 80%. All three calculated androgen indices (FAI, cFT and cBT) showed good correlation with each other. Furthermore, cFT, FAI and calculated BT were shown to be more specific with higher positive likelihood ratio than measured androgen markers. Based on our study, the calculated testosterone indices such as FAI, cBT and cFT are useful markers to distinguish PCOS from non-PCOS. Owing to ease of calculation, FAI can be incorporated in LIS and can be reported with TT and SHBG. This will be helpful for clinician to diagnose hyperandrogenism in PCOS.

Assessment of Energy Savings Potential from the Use of Demand Control Ventilation Systems in General Office Spaces in California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Tianzhen; Fisk, William J.

2009-07-08

Demand controlled ventilation (DCV) was evaluated for general office spaces in California. A medium size office building meeting the prescriptive requirements of the 2008 California building energy efficiency standards (CEC 2008) was assumed in the building energy simulations performed with the EnergyPlus program to calculate the DCV energy savings potential in five typical California climates. Three design occupancy densities and two minimum ventilation rates were used as model inputs to cover a broader range of design variations. The assumed values of minimum ventilation rates in offices without DCV, based on two different measurement methods, were 81 and 28 cfm per occupant. These rates are based on the co-author's unpublished analyses of data from EPA's survey of 100 U.S. office buildings. These minimum ventilation rates exceed the 15 to 20 cfm per person required in most ventilation standards for offices. The cost effectiveness of applying DCV in general office spaces was estimated via a life cycle cost analyses that considered system costs and energy cost reductions. The results of the energy modeling indicate that the energy savings potential of DCV is largest in the desert area of California (climate zone 14), followed by Mountains (climate zone 16), Central Valley (climate zone 12), North Coast (climate zone 3), and South Coast (climate zone 6). The results of the life cycle cost analysis show DCV is cost effective for office spaces if the typical minimum ventilation rates without DCV is 81 cfm per person, except at the low design occupancy of 10 people per 1000 ft{sup 2} in climate zones 3 and 6. At the low design occupancy of 10 people per 1000 ft{sup 2}, the greatest DCV life cycle cost savings is a net present value (NPV) ofmore » $$0.52/ft{sup 2} in climate zone 14, followed by $$0.32/ft{sup 2} in climate zone 16 and $$0.19/ft{sup 2} in climate zone 12. At the medium design occupancy of 15 people per 1000 ft{sup 2}, the DCV savings are higher with a NPV $$0.93/ft{sup 2} in climate zone 14, followed by $$0.55/ft{sup 2} in climate zone 16, $$0.46/ft{sup 2} in climate zone 12, $$0.30/ft{sup 2} in climate zone 3, $$0.16/ft{sup 2} in climate zone 3. At the high design occupancy of 20 people per 1000 ft{sup 2}, the DCV savings are even higher with a NPV $$1.37/ft{sup 2} in climate zone 14, followed by $$0.86/ft{sup 2} in climate zone 16, $$0.84/ft{sup 2} in climate zone 3, $$0.82/ft{sup 2} in climate zone 12, and $0.65/ft{sup 2} in climate zone 6. DCV was not found to be cost effective if the typical minimum ventilation rate without DCV is 28 cfm per occupant, except at high design occupancy of 20 people per 1000 ft{sup 2} in climate zones 14 and 16. Until the large uncertainties about the base case ventilation rates in offices without DCV are reduced, the case for requiring DCV in general office spaces will be a weak case.« less

Prognostic Value of Coronary Artery Calcium in the PROMISE Study (Prospective Multicenter Imaging Study for Evaluation of Chest Pain).

PubMed

Budoff, Matthew J; Mayrhofer, Thomas; Ferencik, Maros; Bittner, Daniel; Lee, Kerry L; Lu, Michael T; Coles, Adrian; Jang, James; Krishnam, Mayil; Douglas, Pamela S; Hoffmann, Udo

2017-11-21

Coronary artery calcium (CAC) is an established predictor of future major adverse atherosclerotic cardiovascular events in asymptomatic individuals. However, limited data exist as to how CAC compares with functional testing (FT) in estimating prognosis in symptomatic patients. In the PROMISE trial (Prospective Multicenter Imaging Study for Evaluation of Chest Pain), patients with stable chest pain (or dyspnea) and intermediate pretest probability for obstructive coronary artery disease were randomized to FT (exercise electrocardiography, nuclear stress, or stress echocardiography) or anatomic testing. We evaluated those who underwent CAC testing as part of the anatomic evaluation (n=4209) and compared that with results of FT (n=4602). We stratified CAC and FT results as normal or mildly, moderately, or severely abnormal (for CAC: 0, 1-99 Agatston score [AS], 100-400 AS, and >400 AS, respectively; for FT: normal, mild=late positive treadmill, moderate=early positive treadmill or single-vessel ischemia, and severe=large ischemic region abnormality). The primary end point was all-cause death, myocardial infarction, or unstable angina hospitalization over a median follow-up of 26.1 months. Cox regression models were used to calculate hazard ratios (HRs) and C statistics to determine predictive and discriminatory values. Overall, the distribution of normal or mildly, moderately, or severely abnormal test results was significantly different between FT and CAC (FT: normal, n=3588 [78.0%]; mild, n=432 [9.4%]; moderate, n=217 [4.7%]; severe, n=365 [7.9%]; CAC: normal, n=1457 [34.6%]; mild, n=1340 [31.8%]; moderate, n=772 [18.3%]; severe, n=640 [15.2%]; P <0.0001). Moderate and severe abnormalities in both arms robustly predicted events (moderate: CAC: HR, 3.14; 95% confidence interval, 1.81-5.44; and FT: HR, 2.65; 95% confidence interval, 1.46-4.83; severe: CAC: HR, 3.56; 95% confidence interval, 1.99-6.36; and FT: HR, 3.88; 95% confidence interval, 2.58-5.85). In the CAC arm, the majority of events (n=112 of 133, 84%) occurred in patients with any positive CAC test (score >0), whereas fewer than half of events occurred in patients with mildly, moderately, or severely abnormal FT (n=57 of 132, 43%; P <0.001). In contrast, any abnormality on FT was significantly more specific for predicting events (78.6% for FT versus 35.2% for CAC; P <0.001). Overall discriminatory ability in predicting the primary end point of mortality, nonfatal myocardial infarction, and unstable angina hospitalization was similar and fair for both CAC and FT (C statistic, 0.67 versus 0.64). Coronary computed tomographic angiography provided significantly better prognostic information compared with FT and CAC testing (C index, 0.72). Among stable outpatients presenting with suspected coronary artery disease, most patients experiencing clinical events have measurable CAC at baseline, and fewer than half have any abnormalities on FT. However, an abnormal FT was more specific for cardiovascular events, leading to overall similarly modest discriminatory abilities of both tests. URL: https://www.clinicaltrials.gov. Unique identifier: NCT01174550. © 2017 American Heart Association, Inc.

Testing Viable f(T) Models with Current Observations

NASA Astrophysics Data System (ADS)

Xu, Bing; Yu, Hongwei; Wu, Puxun

2018-03-01

We perform observational tests on the f(T) gravity with the BAO data (including the BOSS DR 12 galaxy sample, the DR12 Lyα-Forests measurement, the new eBOSS DR14 quasar sample, the 6dFGS, and the SDSS), the CMB distance priors from the Planck 2015, the SNIa data from the joint light-curve analysis, the latest H(z) data, and the local value of the Hubble constant. Six different f(T) models are investigated. Furthermore, the ΛCDM is also considered. All models are compared by using the Akaike information criteria (AIC) and the Bayesian information criteria (BIC). Our results show that the ΛCDM remains to be the most favored model by current observations. However, there are also the Hubble constant tension between the Planck measurements and the local Universe observations and the tension between the CMB data and the H(z) data in the ΛCDM. For f(T) models considered in this paper, half, which can reduce to the ΛCDM, have values of {{χ }2}\\min smaller than that of the ΛCDM and can relieve the tensions existing in the ΛCDM. However, they are punished slightly by the BIC due to one extra parameter. Two of six f(T) models, in which the crossing of the phantom divide line can be realized for the equation of state of the effective dark energy and this crossing is shown in this paper to be favored by current observations, are punished by the information criteria. In addition, we find that the logarithmic f(T) model is excluded by cosmological observations.

Estimation of paleogeothermal gradients and their relationship to timing of petroleum generation, Eagle basin, northwestern Colorado

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nuccio, V.F.; Schenk, C.J.

1988-01-01

Lopatin time-temperature index (TTI) modeling of three locations in the Eagle basin, northwestern Colorado, where vitrinite reflectance (R/sub m/) profiles were obtained, shows that paleogeothermal gradients and the timing of oil generation in the Belden Formation (Pennsylvanian) varied due to differing thickness of the Pennsylvanian section across the basin. At the Gilman location, where the Pennsylvanian section is thickest (7,900 ft or 2,408 m), two paleogeothermal gradient models were generated that match the average 3.70% R/sub m/ and the corresponding TTI value between 40,000 and 50,000. The first model assumes a constant geothermal gradient of 2.4/sup 0/F/100 ft (43.8/sup 0/C/km),more » which places the oil window between 270 and 230 Ma. The second model assumes a changing paleogeothermal gradient of 2.80/sup 0/F/100 ft (51/sup 0/C/km), from 320 to 265 Ma and 2.20/sup 0/F/100 ft (40.2/sup 0/C/km) from 265 Ma to present, which places the oil window between 275 and 250 Ma. For the Glenwood location, where the Pennsylvanian section is 4,960 ft (1,512 m), a constant paleogeothermal gradient of 1.80/sup 0/F/100 ft (32.9/sup 0/C/km) works the best in correlating the 2.50% R/sub m/ with the corresponding TTI value of approximately 2,700. Using this gradient, the oil window falls between 175 and 75 Ma.« less

The influence of natural short photoperiodic and temperature conditions on plasma thyroid hormones and cholesterol in male Syrian hamsters

NASA Astrophysics Data System (ADS)

Vaughan, M. K.; Brainard, G. C.; Reiter, R. J.

1984-09-01

Adult male Syrian hamsters were subjected to 1, 3, 5, 7 or 11 weeks of either natural winter conditions or rigorously controlled laboratory conditions (LD 10∶14; 22 ± 2‡C). Although both groups of hamsters gained weight over the course of the experiment, hamsters housed indoors were significantly heavier after 5 weeks of treatment compared to their outdoors counterparts. Animals housed under natural conditions exhibited a significant decrease in circulating levels of thyroxine (T4) and a rapid rise in triiodothyronine (T3) levels; the free T4 and free T3 index (FT4I and FT3I) mirrored the changes in circulating levels of the respective hormones. Laboratory-housed animals had a slight rise in T4 and FT4I at 3 weeks followed by a slow steady decline in these values; T3 and FT3I values did not change remarkably in these animals. Plasma cholesterol declined steadily over the course of the experiment in laboratory-maintained animals but increased slightly during the first 5 weeks in animals under natural conditions. Since the photoperiodic conditions were approximately of the same duration in these 2 groups, it is concluded that the major differences in body weight, thyroid hormone values and plasma cholesterol are due to some component (possibly temperature) in the natural environment.

Hydrogeologic Framework of the Yakima River Basin Aquifer System, Washington

USGS Publications Warehouse

Vaccaro, J.J.; Jones, M.A.; Ely, D.M.; Keys, M.E.; Olsen, T.D.; Welch, W.B.; Cox, S.E.

2009-01-01

The Yakima River basin aquifer system underlies about 6,200 square miles in south-central Washington. The aquifer system consists of basin-fill deposits occurring in six structural-sedimentary basins, the Columbia River Basalt Group (CRBG), and generally older bedrock. The basin-fill deposits were divided into 19 hydrogeologic units, the CRBG was divided into three units separated by two interbed units, and the bedrock was divided into four units (the Paleozoic, the Mesozoic, the Tertiary, and the Quaternary bedrock units). The thickness of the basin-fill units and the depth to the top of each unit and interbed of the CRBG were mapped. Only the surficial extent of the bedrock units was mapped due to insufficient data. Average mapped thickness of the different units ranged from 10 to 600 feet. Lateral hydraulic conductivity (Kh) of the units varies widely indicating the heterogeneity of the aquifer system. Average or effective Kh values of the water-producing zones of the basin-fill units are on the order of 1 to 800 ft/d and are about 1 to 10 ft/d for the CRBG units as a whole. Effective or average Kh values for the different rock types of the Paleozoic, Mesozoic, and Tertiary units appear to be about 0.0001 to 3 ft/d. The more permeable Quaternary bedrock unit may have Kh values that range from 1 to 7,000 ft/d. Vertical hydraulic conductivity (Kv) of the units is largely unknown. Kv values have been estimated to range from about 0.009 to 2 ft/d for the basin-fill units and Kv values for the clay-to-shale parts of the units may be as small as 10-10 to 10-7 ft/d. Reported Kv values for the CRBG units ranged from 4x10-7 to 4 ft/d. Variations in the concentrations of geochemical solutes and the concentrations and ratios of the isotopes of hydrogen, oxygen, and carbon in groundwater provided information on the hydrogeologic framework and groundwater movement. Stable isotope ratios of water (deuterium and oxygen-18) indicated dispersed sources of groundwater recharge to the CRBG and basin-fill units and that the source of surface and groundwater is derived from atmospheric precipitation. The concentrations of dissolved methane were larger than could be attributable to atmospheric sources in more than 80 percent of wells with measured methane concentrations. The concentrations of the stable isotope of carbon-13 of methane were indicative of a thermogenic source of methane. Most of the occurrences of methane were at locations several miles distant from mapped structural fault features, suggesting the upward vertical movement of thermogenic methane from the underlying bedrock may be more widespread than previously assumed or there may be a more general occurrence of unmapped (buried) fault structures. Carbon and tritium isotope data and the concentrations of dissolved constituents indicate a complex groundwater flow system with multiple contributing zones to groundwater wells and relative groundwater residence time on the order of a few tens to many thousands of years. Potential mean annual recharge for water years 1950-2003 was estimated to be about 15.6 in. or 7,149 ft3/s (5.2 million acre-ft) and includes affects of human activities such as irrigation of croplands. If there had been no human activities (predevelopment conditions) during that time period, estimated recharge would have been about 11.9 in. or 5,450 ft3/s (3.9 million acre-ft). Estimated mean annual recharge ranges from virtually zero in the dry parts of the lower basin to more than 100 in. in the humid uplands, where annual precipitation is more than 120 in. Groundwater in the different hydrogeologic units occurs under perched, unconfined, semiconfined, and confined conditions. Groundwater moves from topographic highs in the uplands to topographic low areas along the streams. The flow system in the basin-fill units is compartmentalized due to topography and geologic structure. The flow system also is compartmentalized for the CRBG units but not to as large

Observations from borehole dilution logging experiments in fractured crystalline rock under variable hydraulic conditions

USGS Publications Warehouse

Harte, Philip T.; Anderson, Alton; Williams, John H.

2014-01-01

Identifying hydraulically active fractures in low permeability, crystalline-bedrock aquifers requires a variety of geophysical and hydrogeophysical borehole tools and approaches. One such approach is Single Borehole Dilution Tests (SBDT), which in some low flow cases have been shown to provide greater resolution of borehole flow than other logging procedures, such as vertical differential Heat Pulse Flowmeter (HPFM) logging. Because the tools used in SBDT collect continuous profiles of water quality or dye changes, they can identify horizontal flow zones and vertical flow. We used SBDT with a food grade blue dye as a tracer and dual photometer-nephelometer measurements to identify low flow zones.SBDT were conducted at seven wells with open boreholes (exceeding 300 ft). At most of the wells HPFM logs were also collected. The seven wells are set in low-permeability, fractured granite and gneiss rocks underlying a former tetrachloroeythylene (PCE) source area at the Savage Municipal Well Superfund site in Milford, NH. Time series SBDT logs were collected at each of the seven wells under three distinct hydraulic conditions: (1) ambient conditions prior to a pump test at an adjacent well, (2) mid test, after 2-3 days of the start of the pump test, and (3) at the end of the test, after 8-9 days of the pump test. None of the SBDT were conducted under pumping conditions in the logged well. For each condition, wells were initially passively spiked with blue dye once and subsequent time series measurements were made.Measurement accuracy and precision of the photometer tool is important in SBDT when attempting to detect low rates of borehole flow. Tests indicate that under ambient conditions, none of the wells had detectable flow as measured with HPFM logging. With SBDT, 4 of the 7 showed the presence of some very low flow. None of 5 (2 of the 7 wells initially logged with HPFM under ambient conditions were not re-logged) wells logged with the HPFM during the pump test had detectable flow. However, 3 of the 5 wells showed the patterns of very low flow with SBDT during the pump test including pumping induced changes of inflow and outflow patterns at one well.

Evaluation of serum free thyroxine and thyrotropin concentrations in the diagnosis of canine hypothyroidism.

PubMed

Dixon, R M; Mooney, C T

1999-02-01

Canine thyroid-stimulating hormone (cTSH), total thyroxine (T4) and free T4 by equilibrium dialysis (fT4d) were measured in serum samples from 107 dogs with clinical signs suggestive of hypothyroidism in which the diagnosis was either confirmed (n = 30) or excluded (n = 77) by exogenous TSH response testing. Median serum total T4 and fT4d concentrations were significantly lower and cTSH significantly higher (P < 0.001) in hypothyroid compared with euthyroid dogs. Differential positive rate analysis determined optimal cut-off values of less than 14.9 nmol/litre (total T4), less than 5.42 pmol/litre (fT4d), greater than 0.68 ng/ml (cTSH), less than 17.3 (T4 to cTSH ratio), and less than 7.5 (fT4d to cTSH ratio) for hypothyroidism. These had a sensitivity and specificity of 100 and 75.3 per cent, 80 and 93.5 per cent, 86.7 and 81.8 per cent, 86.7 and 92.2 per cent, and 80 and 97.4 per cent, respectively, for diagnosing hypothyroidism. Corresponding areas under the receiver operating characteristic curves were 0.92, 0.93, 0.87, 0.93 and 0.93. Unexpectedly low cTSH values in hypothyroid dogs may have resulted from concurrent non-thyroidal illness. Unexpectedly high serum cTSH values in the euthyroid dogs might have resulted from recovery from illness or concurrent potentiated sulphonamide therapy. Measurement of endogenous cTSH concentration is a valuable diagnostic tool for canine hypothyroidism if used in association with assessment of T4. Estimation of fT4d added only limited additional information over total T4 measurement.

Remote-Sensing Survey of the Atchafalaya Basin Main Channel, Atchafalaya Channel Training Project, Sts. Martin and Mary Parishes, Louisiana

DTIC Science & Technology

1991-11-01

Just above Cornay’s Bridge they sunk the steamer Flycatcher and a schooner loaded with bricks, plus live oak trees were cut down and thrown into the...contour level) (Feet) Single Objects Engine camshaft 20 fi x 2 m 45 45 x 50 feet 15 Cas’ Iron soil pipe 10 ft long. 100 lbs 1407 45 x 65 feet 4 Iron...hitting any of the numerous fallen trees , snags, submerged logs, shallow sand bars, etc., 52 Chapter 3. Remote-Sensing Survey which occur along much of the

Characterization and Extraction of Uranium Contamination Perched within the Deep Vadose Zone at the Hanford Site, Washington State

NASA Astrophysics Data System (ADS)

Williams, B. A.; Rohay, V. J.; Benecke, M. W.; Chronister, G. B.; Doornbos, M. H.; Morse, J.

2012-12-01

A highly contaminated perched water zone has been discovered in the deep vadose zone above the unconfined aquifer during drilling of wells to characterize groundwater contamination within the 200 East Area of the U.S. Department of Energy's Hanford Site in southeast Washington. The perched water, which contains nitrate, uranium, and technetium-99 at concentrations that have exceeded 100,000 μg/L, 70,000 μg/L, and 45,000 pCi/L respectively, is providing contamination to the underlying unconfined aquifer. A perched zone extraction well has been installed and is successfully recovering the contaminated perched water as an early remedial measure to reduce impacts to the unconfined aquifer. The integration and interpretation of various borehole hydrogeologic, geochemical, and geophysical data sets obtained during drilling facilitated the delineation of the perching horizon and determination of the nature and extent of the perched contamination. Integration of the borehole geologic and geophysical logs defined the structural elevation and thickness of the perching low permeability silt interval. Borehole geophysical moisture logs, gamma logs, and sample data allowed detailed determination of the elevation and thickness of the oversaturated zone above the perching horizon, and the extent and magnitude of the radiological uranium contamination within the perching interval. Together, these data sets resolved the nature of the perching horizon and the location and extent of the contaminated perched water within the perching zone, allowing an estimation of remaining contaminant extent. The resulting conceptual model indicates that the contaminated perched water is contained within a localized sand lens deposited in a structural low on top of a semi-regional low-permeability silt layer. The top of the sand lens is approximately 72 m (235 ft) below ground surface; the maximum thickness of the sand lens is approximately 3 m (10 ft). The lateral and vertical extent of the perched water is limited to the presence of the sand lens and is approximately 4.6 m (15 ft) above the unconfined aquifer. Liquid wastes containing uranium and technetium-99 that were discharged decades ago to nearby engineered structures for subsurface infiltration and that leaked from single shell storage tanks have migrated vertically and laterally and are accumulating within this sand layer above the perching silt which forms a natural barrier that slows contaminant migration to the aquifer. Extraction of the contaminated perched water began in August 2011 using an automated pumping system installed in a well screened within the perched zone. As of August 1, 2012, approximately 52,000 gallons of perched water containing 115 kg of nitrate, 11.4 kg of uranium and 0.102 mg of technetium-99 have been removed from this zone.

Vibrational and electronic investigations, NLO, FMO analysis on a hetarylazoindole disperse dye by density functional theory

NASA Astrophysics Data System (ADS)

Çatıkkaş, Berna; Aktan, Ebru; Yalçın, Ergin

2016-08-01

This work deals with the optimized molecular structure, vibrational spectra, nonlinear optic (NLO) and frontier molecule orbital (FMO) properties of 1-Methyl-2-phenyl-3-(1,3,4-thiadiazol-2-yldiazenyl)-1H-indole (MPI) by quantum chemical calculations. The Fourier transform infrared (FT-MIR and FT-FIR) and Raman spectra of 1-Methyl-2-phenyl-3-(1,3,4-thiadiazol-2-yldiazenyl)-1H-indole (MPI) were recorded in the region (4000-400 cm-1 and 400-30 cm-1) and (3200-92 cm-1), respectively. The analysis and complete vibrational assignments of the fundamental modes of the MPI molecule were carried out by using the observed FT-IR and FT-Raman data and calculated Total Energy Distribution (TED) according to Scaled Quantum Mechanics procedure. The calculated geometrical parameters of the MPI molecule are in agreement with the obtained values from XRD studies. On the other hand, the difference between the scaled and observed wavenumber values of the most of the fundamentals are very small. 1H NMR and 13C NMR chemical shift values, and energy gap between LUMO-HOMO and molecular electrostatic potential (MEP) were investigated by using density functional theory (B3LYP) methods. UV/Visible spectra and λ maximum absorption values, the oscillator strengths in the chloroform, methanol and DMSO solvation in combination with different basis sets were calculated by using the time-dependent density functional theory (TD-DFT). Additionally, the predicted nonlinear optical (NLO) properties of the MPI are quite greater than that of urea at the B3LYP/6-31++G(d,p) level.

Analysis of aquifer tests in the Punjab region of West Pakistan

USGS Publications Warehouse

Bennett, Gordon D.; ,; Sheikh, Ijaz Ahmed; Alr, Sabire

1967-01-01

The results of 141 pumping tests in the Punjab Plain of West Pakistan are reported. Methods of test analysis are described in detail, and an outline of the theory underlying these methods is given. The lateral permeability of the screened interval is given for all tests; the specific yield of the material at water-table depth is given for 1(6 tests; and the vertical permeability of the material between the water table and the top of the screen is given for 14 tests. The lateral permeabilities are predominantly in the range 0.001 to 0.006 cfs per sq ft; the average value is 0.0032 cfs per sq ft. Specific yields generally range from 0.02 to 0.26; the average value is 0.14. All vertical permeability results fall in the range 10 -5 to 10 -3 cfs per sq ft.

Rill erosion in burned and salvage logged western montane forests: Effects of logging equipment type, traffic level, and slash treatment

Treesearch

J. W. Wagenbrenner; P. R. Robichaud; R. E. Brown

2016-01-01

Following wildfires, forest managers often consider salvage logging burned trees to recover monetary value of timber, reduce fuel loads, or to meet other objectives. Relatively little is known about the cumulative hydrologic effects of wildfire and subsequent timber harvest using logging equipment. We used controlled rill experiments in logged and unlogged (control)...

Lumber value differences from reduced CT spatial resolution and simulated log sawing

Treesearch

Suraphan Thawornwong; Luis G. Occena; Daniel L. Schmoldt

2003-01-01

In the past few years, computed tomography (CT) scanning technology has been applied to the detection of internal defects in hardwood logs for the purpose of obtaining a priori information that can be used to arrive at better log sawing decisions. Because sawyers currently cannot even see the inside of a log until the log faces are revealed by sawing, there is little...

Relationship between left ventricular mechanics and low free triiodothyronine levels after myocardial infarction: a prospective study.

PubMed

Jankauskienė, Edita; Orda, Paulius; Barauskienė, Greta; Mickuvienė, Narseta; Brožaitienė, Julija; Vaškelytė, Jolanta Justina; Bunevičius, Robertas

2016-04-01

Low free triiodothyronine (fT3) levels following acute myocardial infarction (AMI) are associated with greater impairment in cardiac mechanics compared with patients with AMI who have normal values of thyroid hormones. The objectives are to investigate left ventricular (LV) function and mechanics during a 6-month follow-up after myocardial infarction and to evaluate their prognostic implication using two-dimensional (2D) echocardiography and 2D speckle-tracking echocardiography in patients with low fT3 levels. The study design is prospective cohort study. One hundred forty patients with first-onset AMI were grouped according to serum fT3 levels: low fT3 group (fT3 <3.2 pmol/L; n = 44) and control group (fT3 >3.2 pmol/L; n = 96). Low levels of fT3 were associated with greater LV diameters and LV end-diastolic volume, and decreased systolic LV function. Systolic apical and basal rotation, peak systolic global longitudinal strain and strain rate, and LV twist and torsion were significantly decreased in the low fT3 group. The prognostic implication for predicting low fT3 levels was evaluated using ROC analysis. LV end-diastolic diameter index is the most sensitive (94.12 %), but has low specificity (37.93 %; area = 0.659, p = 0.01). By contrast, LV end-systolic volume is the most specific (94.03 %), but has low sensitivity (26.32 %; area = 0.594, p = 0.04). Low fT3 levels are significantly associated with worse LV mechanics. Low fT3 levels are important for prediction of LV structure, function, rotation, and deformation parameters during the late post-myocardial infarction period.

Use of Cutting-Edge Horizontal and Underbalanced Drilling Technologies and Subsurface Seismic Techniques to Explore, Drill and Produce Reservoired Oil and Gas from the Fractured Monterey Below 10,000 ft in the Santa Maria Basin of California

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Witter; Robert Knoll; William Rehm

2005-09-29

This project was undertaken to demonstrate that oil and gas can be drilled and produced safely and economically from a fractured Monterey reservoir in the Santa Maria Basin of California by employing horizontal wellbores and underbalanced drilling technologies. Two vertical wells were previously drilled in this area with heavy mud and conventional completions; neither was commercially productive. A new well was drilled by the project team in 2004 with the objective of accessing an extended length of oil-bearing, high-resistivity Monterey shale via a horizontal wellbore, while implementing managed-pressure drilling (MPD) techniques to avoid formation damage. Initial project meetings were conductedmore » in October 2003. The team confirmed that the demonstration well would be completed open-hole to minimize productivity impairment. Following an overview of the geologic setting and local field experience, critical aspects of the application were identified. At the pre-spud meeting in January 2004, the final well design was confirmed and the well programming/service company requirements assigned. Various design elements were reduced in scope due to significant budgetary constraints. Major alterations to the original plan included: (1) a VSP seismic survey was delayed to a later phase; (2) a new (larger) surface hole would be drilled rather than re-enter an existing well; (3) a 7-in. liner would be placed into the top of the Monterey target as quickly as possible to avoid problems with hole stability; (4) evaluation activities were reduced in scope; (5) geosteering observations for fracture access would be deduced from penetration rate, cuttings description and hydrocarbon in-flow; and (6) rather than use nitrogen, a novel air-injection MPD system was to be implemented. Drilling operations, delayed from the original schedule by capital constraints and lack of rig availability, were conducted from September 12 to November 11, 2004. The vertical and upper curved sections were drilled and lined through the problematic shale member without major stability problems. The top of the targeted Monterey was thought to be seen at the expected TVD of 10,000 ft where the 7-in. liner was set at a 60{sup o} hole angle. Significant oil and gas shows suggested the fractured interval anticipated at the heel location had been penetrated. A total of 2572 ft of 6 1/8-in. near-horizontal interval was placed in the shale section, extending planned well length by approximately 470 ft. Very little hydrocarbon in-flow was observed from fractures along the productive interval. This may be a result of the well trajectory falling underneath the Monterey fractured zone. Hydrocarbon observations, cuttings analysis and gamma-ray response indicated additional fractured intervals were accessed along the last {+-}900 ft of well length. The well was completed with a 2 7/8-in. tubing string set in a production packer in preparation for flow and swab tests to be conducted later by a service rig. The planned well time was estimated as 39 days and overall cost as $2.4 million. The actual results are 66 days at a total cost of $3.4 million. Well productivity responses during subsequent flow and swabbing tests were negative. The well failed to inflow and only minor amounts (a few barrels) of light oil were recovered. The lack of production may suggest that actual sustainable reservoir pressure is far less than anticipated. Temblor is currently planning to re-enter and clean out the well and run an Array Induction log (primarily for resistivity and correlation purposes), and an FMI log (for fracture detection). Depending on the results of these logs, an acidizing or re-drill program will be planned.« less

Estimate of standard deviation for a log-transformed variable using arithmetic means and standard deviations.

PubMed

Quan, Hui; Zhang, Ji

2003-09-15

Analyses of study variables are frequently based on log transformations. To calculate the power for detecting the between-treatment difference in the log scale, we need an estimate of the standard deviation of the log-transformed variable. However, in many situations a literature search only provides the arithmetic means and the corresponding standard deviations. Without individual log-transformed data to directly calculate the sample standard deviation, we need alternative methods to estimate it. This paper presents methods for estimating and constructing confidence intervals for the standard deviation of a log-transformed variable given the mean and standard deviation of the untransformed variable. It also presents methods for estimating the standard deviation of change from baseline in the log scale given the means and standard deviations of the untransformed baseline value, on-treatment value and change from baseline. Simulations and examples are provided to assess the performance of these estimates. Copyright 2003 John Wiley & Sons, Ltd.

Air-to-Air Visual Acquisition Handbook

DTIC Science & Technology

1991-11-27

expending a normal amount of effort on visual search. * A target aicraft begins to approach. Itisa - IACT= 1 Piper PA-28 flying on an unaccelerated...output for SEEL. 17 TABLE 4.1 AIRCRAFT TYPES USED IN SEEI AX AY AZ IACT AIRCRAFT TYPE NAME (sq. ft.) (sq. ft.) (sq. ft.) 1 Piper PA-28 PA28 35 85 260 2...VSUB 180.0 FOVL -120.00 T2 12.0 VTAR 130.0 FOVR 90.0 D1 0.00 IACT 1.00 D2 0.00 XANG 90.0 * - initial value (before iteration) ROW VARIABLE: BETL is

Fuels planning: science synthesis and integration; economic uses fact sheet 07: markets and log prices

Treesearch

Rocky Mountain Research Station USDA Forest Service

2004-01-01

Markets and prices for logs vary widely across the West, fluctuating from place to place in response to regional variables and hauling costs. This fact sheet discusses those variables, locality of log markets, markets for low-value logs, and caveats to consider when using My Fuel Treatment Planner.

Armored instrumentation cable for geothermal well logging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dennis, B.R.; Johnson, J.; Todd, B.

1981-01-01

Multiconductor armored well-logging cable is used extensively by the oil and natural gas industry to lower various instruments used to measure the geological and geophysical parameters into deep wellbores. Advanced technology in oil-well drilling makes it possible to achieve borehole depths of 9 km (30,000 ft). The higher temperatures in these deeper boreholes demand advancements in the design and manufacturing of wireline cable and in the electrical insulating and armoring materials used as integral components. If geothermal energy is proved an abundant economic resource, drilling temperatures approaching and exceeding 300/sup 0/C will become commonplace. The adaptation of teflons as electricalmore » insulating material permitted use of armored cable in geothermal wellbores where temperatures are slightly in excess of 200/sup 0/C, and where the concentrations of corrosive minerals and gases are high. Teflon materials presently used in wireline cables, however, are not capable of continuous operation at the anticipated higher temperatures.« less

Core drilling provides information about Santa Fe Group aquifer system beneath Albuquerque's West Mesa

USGS Publications Warehouse

Allen, B.D.; Connell, S.D.; Hawley, J.W.; Stone, B.D.

1998-01-01

Core samples from the upper ???1500 ft of the Santa Fe Group in the Albuquerque West Mesa area provide a first-hand look at the sediments and at subsurface stratigraphic relationships in this important part of the basin-fill aquifer system. Two major hydrostratigraphic subunits consisting of a lower coarse-grained, sandy interval and an overlying fine-grained, interbedded silty sand and clay interval lie beneath the water table at the 98th St core hole. Borehole electrical conductivity measurements reproduce major textural changes observed in the recovered cores and support subsurface correlations of hydrostratigraphic units in the Santa Fe Group aquifer system based on geophysical logs. Comparison of electrical logs from the core hole and from nearby city wells reveals laterally consistent lithostratigraphic patterns over much of the metropolitan area west of the Rio Grande that may be used to delineate structural and related stratigraphic features that have a direct bearing on the availability of ground water.

Efficient parallel algorithms for string editing and related problems

NASA Technical Reports Server (NTRS)

Apostolico, Alberto; Atallah, Mikhail J.; Larmore, Lawrence; Mcfaddin, H. S.

1988-01-01

The string editing problem for input strings x and y consists of transforming x into y by performing a series of weighted edit operations on x of overall minimum cost. An edit operation on x can be the deletion of a symbol from x, the insertion of a symbol in x or the substitution of a symbol x with another symbol. This problem has a well known O((absolute value of x)(absolute value of y)) time sequential solution (25). The efficient Program Requirements Analysis Methods (PRAM) parallel algorithms for the string editing problem are given. If m = ((absolute value of x),(absolute value of y)) and n = max((absolute value of x),(absolute value of y)), then the CREW bound is O (log m log n) time with O (mn/log m) processors. In all algorithms, space is O (mn).

Logarithmic compression methods for spectral data

DOEpatents

Dunham, Mark E.

2003-01-01

A method is provided for logarithmic compression, transmission, and expansion of spectral data. A log Gabor transformation is made of incoming time series data to output spectral phase and logarithmic magnitude values. The output phase and logarithmic magnitude values are compressed by selecting only magnitude values above a selected threshold and corresponding phase values to transmit compressed phase and logarithmic magnitude values. A reverse log Gabor transformation is then performed on the transmitted phase and logarithmic magnitude values to output transmitted time series data to a user.

The (C III lambda 1909/Si III lambda 1892) ratio as a diagnostic for planetary nebulae and symbiotic stars

NASA Technical Reports Server (NTRS)

Feibelman, Walter A.; Aller, Lawrence H.

1987-01-01

Suitable IUE archival material on planetary nebulae has been examined to determine the log R /F(lambda 1909 C III)/F(lambda 1892 Si III)/ as a discriminant for distinguishing planetary nebulae from symbiotic stars and related objects. The mean value of log R for 73 galactic planetaries is 1.4, while that of extragalactic planetaries appears to be slightly lower, and that for symbiotics is 0.3. The lower value of log R for symbiotics is easily understood as a consequence of their higher densities. A plot of log R versus N-epsilon indicates that 80 percent of the planetaries fall into the range of log R between 1.2 and 1.8, but some of the 'peculiar' and bipolar nebulae fall below log R = 1.2. The corresponding N(C++)/N(Si++) ionic ratio varies over a large range.

Salt-dome-related diagenesis of Miocene sediment, Black Bayou field, Cameron Parish, Louisiana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leger, W.R.

1988-09-01

The Black Bayou field is associated with a salt dome that pierces Miocene sediment and rises to within 900 ft (275 m) of the surface. The Louisiana Gulf Coast regional geothermal gradient is locally affected by the salt dome. The gradient increases to values greater than the regional gradient, 1.26/degrees/F/100 ft (23/degrees/C/km), near the dome. Local effects of the salt dome on clastic diagenesis have been determined by studying sandstone samples adjacent to and away from the salt dome within Miocene sediment. Sample depths range from 4155 to 6145 ft (1266 to 1873 m). Distances of samples from the edgemore » of the dome range from 82 to 820 ft (25 to 250 m).« less

Predictive performance of the human Cell Line Activation Test (h-CLAT) for lipophilic chemicals with high octanol-water partition coefficients.

PubMed

Takenouchi, Osamu; Miyazawa, Masaaki; Saito, Kazutoshi; Ashikaga, Takao; Sakaguchi, Hitoshi

2013-01-01

To meet the urgent need for a reliable alternative test for predicting skin sensitizing potential of many chemicals, we have developed a cell-based in vitro test, human Cell Line Activation Test (h-CLAT). However, the predictive performance for lipophilic chemicals in the h-CLAT still remains relatively unknown. Moreover, it's suggested that low water solubility of chemicals might induce false negative outcomes. Thus, in this study, we tested relatively low water soluble 37 chemicals with log Kow values above and below 3.5 in the h-CLAT. The small-scale assessment resulted in nine false negative outcomes for chemicals with log Kow values greater than 3.5. We then created a dataset of 143 chemicals by combining the existing dataset of 106 chemicals and examined the predictive performance of the h-CLAT for chemicals with a log Kow of less than 3.5; a total of 112 chemicals from the 143 chemicals in the dataset. The sensitivity and overall accuracy for the 143 chemicals were 83% and 80%, respectively. In contrast, sensitivity and overall accuracy for the 112 chemicals with log Kow values below 3.5 improved to 94% and 88%, respectively. These data suggested that the h-CLAT could successfully detect sensitizers with log Kow values up to 3.5. When chemicals with log Kow values greater than 3.5 that were deemed positive by h-CLAT were included with the 112 chemicals, the sensitivity and accuracy in terms of the resulting applicable 128 chemicals out of the 143 chemicals became 95% and 88%, respectively. The use of log Kow values gave the h-CLAT a higher predictive performance. Our results demonstrated that the h-CLAT could predict sensitizing potential of various chemicals, which contain lipophilic chemicals using a large-scale chemical dataset.

Ventilation-perfusion distribution in normal subjects.

PubMed

Beck, Kenneth C; Johnson, Bruce D; Olson, Thomas P; Wilson, Theodore A

2012-09-01

Functional values of LogSD of the ventilation distribution (σ(V)) have been reported previously, but functional values of LogSD of the perfusion distribution (σ(q)) and the coefficient of correlation between ventilation and perfusion (ρ) have not been measured in humans. Here, we report values for σ(V), σ(q), and ρ obtained from wash-in data for three gases, helium and two soluble gases, acetylene and dimethyl ether. Normal subjects inspired gas containing the test gases, and the concentrations of the gases at end-expiration during the first 10 breaths were measured with the subjects at rest and at increasing levels of exercise. The regional distribution of ventilation and perfusion was described by a bivariate log-normal distribution with parameters σ(V), σ(q), and ρ, and these parameters were evaluated by matching the values of expired gas concentrations calculated for this distribution to the measured values. Values of cardiac output and LogSD ventilation/perfusion (Va/Q) were obtained. At rest, σ(q) is high (1.08 ± 0.12). With the onset of ventilation, σ(q) decreases to 0.85 ± 0.09 but remains higher than σ(V) (0.43 ± 0.09) at all exercise levels. Rho increases to 0.87 ± 0.07, and the value of LogSD Va/Q for light and moderate exercise is primarily the result of the difference between the magnitudes of σ(q) and σ(V). With known values for the parameters, the bivariate distribution describes the comprehensive distribution of ventilation and perfusion that underlies the distribution of the Va/Q ratio.

AM2 Mat End Connector Modeling and Performance Validation

DTIC Science & Technology

2015-08-01

9 3.2.1 Subgrade construction and posttest forensics...layout. 3.2.1 Subgrade construction and posttest forensics The test section subgrade was built using in-place material from a previous AM2 test...area 50 ft wide by 42 ft long of the existing test bed was removed and replaced with newly processed material. Posttest values from the previous

Water pressure and ground vibrations induced by water guns at a backwater pond on the Illinois River near Morris, Illinois

USGS Publications Warehouse

Koebel, Carolyn M.; Egly, Rachel M.

2016-09-27

Three different geophysical sensor types were used to characterize the underwater pressure waves and ground velocities generated by the underwater firing of seismic water guns. These studies evaluated the use of water guns as a tool to alter the movement of Asian carp. Asian carp are aquatic invasive species that threaten to move into the Great Lakes Basin from the Mississippi River Basin. Previous studies have identified a threshold of approximately 5 pounds per square inch (lb/in2) for behavioral modification and for structural limitation of a water gun barrier.Two studies were completed during August 2014 and May 2015 in a backwater pond connected to the Illinois River at a sand and gravel quarry near Morris, Illinois. The August 2014 study evaluated the performance of two 80-cubic-inch (in3) water guns. Data from the 80-in3 water guns showed that the pressure field had the highest pressures and greatest extent of the 5-lb/in2 target value at a depth of 5 feet (ft). The maximum recorded pressure was 13.7 lb/in2, approximately 25 ft from the guns. The produced pressure field took the shape of a north-south-oriented elongated sphere with the 5-lb/in2 target value extending across the entire study area at a depth of 5 ft. Ground velocities were consistent over time, at 0.0067 inches per second (in/s) in the transverse direction, 0.031 in/s in the longitudinal direction, and 0.013 in/s in the vertical direction.The May 2015 study evaluated the performance of one and two 100-in3 water guns. Data from the 100-in3 water guns, fired both individually and simultaneously, showed that the pressure field had the highest pressures and greatest extent of the 5-lb/in2 target value at a depth of 5 ft. The maximum pressure was 57.4 lb/in2, recorded at the underwater blast sensor closest to the water guns (at a horizontal distance of approximately 3 ft), as two guns fired simultaneously. Pressures and extent of the 5-lb/in2 target value decrease above and below this 5-ft depth, producing a relatively north-south-oriented pressure field shaped like an elongated sphere.

Ground-Water Flow in the Vicinity of the Ho-Chunk Nation Communities of Indian Mission and Sand Pillow, Jackson County, Wisconsin

USGS Publications Warehouse

Dunning, Charles P.; Mueller, Gregory D.; Juckem, Paul F.

2008-01-01

An analytic element ground-water-flow model was constructed to help understand the ground-water-flow system in the vicinity of the Ho-Chunk Nation communities of Indian Mission and Sand Pillow in Jackson County, Wisconsin. Data from interpretive reports, well-drillers' construction reports, and an exploratory augering program in 2003 indicate that sand and gravel of varying thickness (0-150 feet[ft]) and porous sandstone make up a composite aquifer that overlies Precambrian crystalline rock. The geometric mean values for horizontal hydraulic conductivity were estimated from specific-capacity data to be 61.3 feet per day (ft/d) for sand and gravel, 6.6 ft/d for sandstone, and 12.0 ft/d for the composite aquifer. A ground-water flow model was constructed, the near field of which encompassed the Levis and Morrison Creeks Watershed. The flow model was coupled to the parameter-estimation program UCODE to obtain a best fit between simulated and measured values of ground-water levels and estimated Q50 flow duration (base flow). Calibration of the model with UCODE provided a ground-water recharge rate of 9 inches per year and a horizontal hydraulic conductivity of 13 ft/d for the composite aquifer. Using these calibrated parameter values, simulated heads from the model were on average within 5 ft of the measured water levels. In addition, these parameter values provided an acceptable base-flow calibration for Hay, Dickey, and Levis Creeks; the calibration was particularly close for Levis Creek, which was the most frequently measured stream in the study area. The calibrated model was used to simulate ground-water levels and to determine the direction of ground-water flow in the vicinity of Indian Mission and Sand Pillow communities. Backward particle tracking was conducted for Sand Pillow production wells under two pumping simulations to determine their 20-year contributing areas. In the first simulation, new production wells 6, 7, and 8 were each pumped at 50 gallons per minute (gal/min). In the second simulation, new production wells 6, 7, and 8 and existing production well 5 were each pumped at 50 gal/min. The second simulation demonstrated interference between the existing production well 5 and the new production wells when all were pumping at 50 gal/min.

Multilaboratory comparison of hepatitis C virus viral load assays.

PubMed

Caliendo, A M; Valsamakis, A; Zhou, Y; Yen-Lieberman, B; Andersen, J; Young, S; Ferreira-Gonzalez, A; Tsongalis, G J; Pyles, R; Bremer, J W; Lurain, N S

2006-05-01

We report a multilaboratory evaluation of hepatitis C virus (HCV) viral load assays to determine their linear range, reproducibility, subtype detection, and agreement. A panel of HCV RNA samples ranging in nominal concentration from 1.0 to 7.0 log10 IU/ml was constructed by diluting a clinical specimen (genotype 1b). Replicates of the panel were tested in multiple laboratories using the Abbott TaqMan analyte-specific reagent (Abbott reverse transcription-PCR [RT-PCR]), Roche TaqMan RUO (Roche RT-PCR), Roche Amplicor Monitor HCV 2.0 (Roche Monitor), and Bayer VERSANT HCV RNA 3.0 (Bayer bDNA) assays. Bayer bDNA-negative specimens were tested reflexively using the Bayer VERSANT HCV RNA qualitative assay (Bayer TMA). Abbott RT-PCR and Roche RT-PCR detected all 28 replicates with a concentration of 1.0 log10 IU/ml and were linear to 7.0 log10 IU/ml. Roche Monitor and Bayer bDNA detected 27 out of 28 and 13 out of 28 replicates, respectively, of 3.0 log10 IU/ml. Bayer TMA detected all seven replicates with 1.0 log10 IU/ml. Bayer bDNA was the most reproducible of the four assays. The mean viral load values for panel members in the linear ranges of the assays were within 0.5 log10 for the different tests. Eighty-nine clinical specimens of various genotypes (1 through 4) were tested in the Bayer bDNA, Abbott RT-PCR, and Roche RT-PCR assays. For Abbott RT-PCR, mean viral load values were 0.61 to 0.96 log10 greater than the values for Bayer bDNA assay for samples with genotype 1, 2, or 3 samples and 0.08 log10 greater for genotype 4 specimens. The Roche RT-PCR assay gave mean viral load values that were 0.28 to 0.82 log10 greater than those obtained with the Bayer bDNA assay for genotype 1, 2, and 3 samples. However, for genotype 4 samples the mean viral load value obtained with the Roche RT-PCR assay was, on average, 0.15 log10 lower than that of the Bayer bDNA. Based on these data, we conclude that the sensitivity and linear range of the Abbott and Roche RT-PCR assays enable them to be used for HCV diagnostics and therapeutic monitoring. However, the differences in the viral load values obtained with the different assays underscore the importance of using one assay when monitoring response to therapy.

Measurement of diffusion coefficients of parabens and steroids in water and 1-octanol.

PubMed

Seki, Toshinobu; Mochida, Junko; Okamoto, Maiko; Hosoya, Osamu; Juni, Kazuhiko; Morimoto, Kazuhiro

2003-06-01

Diffusion coefficients (D) of parabens and steroids in water and 1-octanol were determined by using the chromatographic broadening method at 37 degrees C, and the relationships between the D values and the physicochemical properties of the drugs were discussed. The D values in 1-octanol were lower than those in water because of the higher viscosity of 1-octanol. The D values depend on not only the molecular weight (MW), but also the lipophilicity of the drugs in water and on the ability for hydrogen-bonding in 1-octanol. When the lipophilic index (LI), calculated from the retention time using in a reverse-phase column, was used as a parameter of drug lipophilicity, the following equation was obtained for D in water (D(w)); log D(w)=-0.215.log MW-0.077.log LI-4.367. When the hydrogen bond index (HI), the logarithm of the ratio of the partition coefficient of the drugs in 1-octanol and cyclohexane, was used as an index of hydrogen-bonding, the following equation was obtained for D in 1-octanol (D(o)); log D(o)=-0.690.log MW-0.074.log HI-4.085.

The contribution of total and free iodothyronines to welfare maintenance and management stress coping in Ruminants and Equines: Physiological ranges and reference values.

PubMed

Ferlazzo, Adriana; Cravana, Cristina; Fazio, Esterina; Medica, Pietro

2018-06-01

In order to acquire a pattern of thyroid involvement in welfare maintenance in Ruminants and Equines, this review summarizes data concerning the reference values of total and free iodothyronines and their modifications in physiological conditions and in different management conditions (pregnancy, lactation, weaning, growth, isolation, restraint, shearing, confinement and transportation). Thyroidal and extrathyroidal tissues efficiently respond to management practices, giving a differentiated contribution to circulating iodothyronine changes. The hormonal response could be mainly attributed to the intracellular deiodination of T 4 to T 3. Triiodothyronine (T 3 ) and free iodothyronines (fT 3 and fT 4 ) result more responsive to management stress, showing different pattern with species and to various conditions, as to environmental conditions in which activities are performed. Intrinsic seasonal changes of iodothyronines and a significant pregnancy effect for T 3 were recorded in mares. Higher, although not significant, T 3 and T 4 concentrations in barren than pregnant mares were observed in donkeys. A positive significant correlation between T 3 and T 4 was described only in pregnant donkeys. Moreover, a significant effect of season on T 3 and fT 3 changes was observed both in pregnant and barren donkeys. A significant lactating effect compared with nonlactating stage for T 3 and T 4 was recorded in mares. In growing foals, body weight (BW) and age were positively correlated with T 3 and negatively correlated with T 4 , fT 4 and fT 3 . Weaning effects were shown for T 3 and fT 4 concentrations, indicating that weaning represents a severe stress and the presence of conspecific does not reduce psychological stress in this phase. Lambs showed significant decreased T 3 and elevated T 4 concentrations two weeks after weaning, with higher concentrations in both males and females compared to 24 h. Significant positive correlations were observed between BW and T 4 , fT 3 and fT 4 concentrations in lambs. A T 3 decrease was detected after isolation, such as induced by confinement and weaning in lambs. Higher T 3 concentration after restraint and shearing than after isolation and significant increases in T 4 , fT 3 and fT 4 values after restraint and shearing were recorded. The basal concentrations of fT 3 in both the inexperienced and experienced transported horses were significantly higher than in untransported experienced horses. Moreover, increases of T 3, T 4 and fT 4 after short road transportation, and significant correlations between T 3 and rectal temperature (RT), body weight (BW) and heart rate (HR), confirmed their important role in coping strategy. Thyroid responsiveness to short transport is similar in domestic donkeys and horses, with a preferential release of T 3 in horses. A greatest and constant release of T 3 and T 4 , although differentiated, after simulated transportation and after conventional transport of horses confirmed that the degree of stress induced by confinement and additional stressful stimuli associated to road transportation could differently influence the iodothyronine release. Temperamental Limousin young beef bulls showed lower T 4 and fT 4 concentrations after prolonged transportation than calm subjects, and a concomitant decrease of circulating ACTH, cortisol, T 3 and fT 3 concentrations, probably induced by down regulation of HPA axis and cortisol negative feedback. These data reinforce the importance of taking into account the evaluation of iodothyronines, and notably of T 3 , as markers of welfare and stress and their role in ensuring energy homeostasis and productive and reproductive performances in Ruminants and Equines. Copyright © 2018 Elsevier Ltd. All rights reserved.

The differential time courses of the vasodilator effects of various 1,4-dihydropyridines in isolated human small arteries are correlated to their lipophilicity.

PubMed

van der Lee, R; Pfaffendorf, M; van Zwieten, P A

2000-11-01

To investigate a possible relationship between the time courses of action of various calcium antagonists and their lipophilicity, characterized as log P-values. The functional experiments were performed in vitro in human small subcutaneous arteries (internal diameter 591 +/- 51 microm, n = 7 for each concentration), obtained from cosmetic surgery (mamma reduction and abdominoplasty). The vessels were investigated in an isometric wire myograph. The vasodilator effect of the calcium antagonists was quantified by means of log IC50-values, and the onset of the vasodilator effect for each concentration studied was expressed as time to Eeq90-values (time to reach 90% of the maximal effect). Log IC50-values were -8.46 +/- 0.09, -8.33 +/- 0.25 and -8.72 +/- 0.16 for nifedipine, felodipine and (S)-lercanidipine, respectively (not significant). On average, nifedipine reached time to Eeq90 in 11 +/- 1 min. For felodipine and (S)-lercanidipine the corresponding values were 60 +/- 11 min and 99 +/- 9 min, respectively. The differences between these values were statistically significant (P< 0.01). In spite of these differences in the in-vitro human vascular model, the three calcium antagonists are equipotent with regard to their vasodilator effects. Linear regression analysis of the correlation between the logarithm of the membrane partition coefficient (log P-values) of the calcium antagonists tested [2.50, 4.46 and 6.88 for nifedipine, felodipine and (S)-lercanidipine, respectively] and their respective values found for time to Eeq90 was highly significant. It appears that a higher log P-value is correlated with a slower onset of action.

Breed-specific reference intervals for assessing thyroid function in seven dog breeds.

PubMed

Hegstad-Davies, Rebecca L; Torres, Sheila M F; Sharkey, Leslie C; Gresch, Sarah C; Muñoz-Zanzi, Claudia A; Davies, Peter R

2015-11-01

Thyroxine (T4), free T4 (FT4), and thyrotropin (TSH) concentrations were measured in serum from 693 healthy representatives from 7 dog breeds (Alaskan Malamute, Collie, English Setter, Golden Retriever, Keeshond, Samoyed, or Siberian Husky) to determine whether breed-specific reference intervals (RIs) are warranted. Veterinarians reviewed the health history, performed a physical examination, and approved laboratory data for the enrolled dogs. Many purebred dogs had T4 and FT4 concentrations that were at, or below, the lower limits previously determined for non-breed-specific RIs. Mean concentrations of T4, FT4, and TSH varied significantly among breeds. The range of mean concentration of T4 (19.7 nmol/L [1.53 µg/dL] in English Setters to 29.0 nmol/L [2.25 µg/dL] in Keeshonds) and FT4 (12.6 pmol/L [0.98 ng/dL] in English Setters to 20.2 pmol/L [1.57 ng/dL] in Samoyeds) was considerable. Median TSH values ranged from 6.10 mIU/L (0.07 ng/mL; Alaskan Malamute and Golden Retriever) to 17.6 mIU/L (0.26 ng/mL; Collie). Mean T4 and FT4 concentrations were higher in females. Increasing age was associated with decreasing T4 and FT4, and increasing TSH concentration. The substantial ranges across breeds of measures of central tendency (mean, median) for all hormones indicate that breed-specific RIs are warranted. RIs encompassing the central 95% of reference values for all breeds combined, and for individual breeds, were calculated using nonparametric (TSH) and robust (T4, FT4) methods. Use of breed-specific RIs in combination with careful attention to the potential for pre-analytical and analytical variability in test results will improve thyroid function assessment in these breeds. © 2015 The Author(s).

Reference Values for TSH and Free Thyroid Hormones in Healthy Pregnant Women in Poland: A Prospective, Multicenter Study.

PubMed

Kostecka-Matyja, Marta; Fedorowicz, Anna; Bar-Andziak, Ewa; Bednarczuk, Tomasz; Buziak-Bereza, Monika; Dumnicka, Paulina; Górska, Maria; Krasnodębska, Małgorzata; Niedźwiedzka, Beata; Pach, Dorota; Ruchała, Marek; Siewko, Katarzyna; Solnica, Bogdan; Sowiński, Jerzy; Szelachowska, Małgorzata; Trofimiuk-Müldner, Małgorzata; Wachowiak-Ochmańska, Katarzyna; Hubalewska-Dydejczyk, Alicja

2017-04-01

The diagnosis and treatment of thyroid diseases in pregnant women remains a challenge. Various medical associations recommend establishing the reference intervals for thyroid hormones by a local laboratory. Considering differences within geophysical, socioeconomic conditions, and iodine prophylaxis in various populations, it is advisable to assess reference intervals for thyroid hormones specific to a region of residence. The objective was to assess trimester-specific reference intervals for TSH, fT 3 , and fT 4 for pregnant women in the Polish population. We conducted a prospective study in 4 centers representing different regions of Poland (Krakow, Warsaw, Poznan, and Bialystok). Our study included consecutive, healthy pregnant women (172 patients), with an age range of 27-47 years. All women had a negative history for thyroid diseases, normal thyroid peroxidase antibody levels, and proper iodine prophylaxis. All newborns had TSH levels in the appropriate reference range. Serum TSH, fT 3 , fT 4 , and thyroid-peroxidase antibodies were measured in each trimester. The reference intervals were calculated using the percentile method, as recommended by the International Federation of Clinical Chemistry. The reference values calculated were 0.009-3.177, 0.05-3.442, and 0.11-3.53 mIU/L for TSH; 3.63-6.55, 3.29-5.45, and 3.1-5.37 pmol/L for fT 3 ; and 11.99-21.89, 10.46-16.67, and 8.96-17.23 pmol/L for fT 4 in consecutive trimesters of pregnancy. Reference intervals for pregnant women when compared to the general population showed a lower concentration of TSH in every trimester of pregnancy and lower fT 4 in the 2nd and 3rd trimesters. Using appropriate trimester-specific reference intervals may improve care of pregnant women by preventing misdiagnosis and inadequate treatment.

Impact of thyroid function abnormalities on reproductive hormones during menstrual cycle in premenopausal HIV infected females at NAUTH, Nnewi, Nigeria

PubMed Central

Emelumadu, Obiageli Fidelia; Igwegbe, Anthony Osita; Monago, Ifeoma Nwamaka; Ilika, Amobi Linus

2017-01-01

Background This was a prospective study designed to evaluate the impact of thyroid function abnormalities on reproductive hormones during menstrual cycle in HIV infected females at Nnamdi Azikiwe University Teaching Hospital Nnewi, South-East Nigeria. Methods The study randomly recruited 35 Symptomatic HIV infected females and 35 Symptomatic HIV infected females on antiretroviral therapy (HAART) for not less than six weeks from an HIV clinic and 40 apparently heathy control females among the hospital staff of NAUTH Nnewi. They were all premenopausal females with regular menstrual cycle and aged between 15–45 years. Blood samples were collected at follicular and luteal phases of their menstrual cycle for assay of Thyroid indices (FT3, FT4 and TSH) and Reproductive indices (FSH, LH, Estrogen, Progesterone, Prolactin and Testosterone) using ELISA method. Results The result showed significantly higher FSH and LH but significantly lower progesterone (prog) and estrogen (E2) in the test females compared to control females at both phases of menstrual cycle (P<0.05). There was significantly lower FT3 but significantly higher TSH value in Symptomatic HIV females (P<0.05). FSH, LH and TSH values were significantly lowered while prog and FT3 were significantly higher in Symptomatic HIV on ART compared to Symptomatic HIV females (P<0.05). FT3, FT4, Prog and E2 were inversely correlated while FSH and LH were positively correlated with duration of HIV infection in HIV females (P<0.05 respectively). There was a direct correlation between CD4+ count and FT3 while inverse correlation was found between CD4+ count and TSH levels (P<0.05). Discussion The present study demonstrated hypothyroidism with a significant degree of primary hypogonadism in Symptomatic HIV infected females at both follicular and luteal phases of menstrual cycle which tends to normalize on treatments. PMID:28723963

Interactive machine learning for postprocessing CT images of hardwood logs

Treesearch

Erol Sarigul; A. Lynn Abbott; Daniel L. Schmoldt

2003-01-01

This paper concerns the nondestructive evaluation of hardwood logs through the analysis of computed tomography (CT) images. Several studies have shown that the commercial value of resulting boards can be increased substantially if log sawing strategies are chosen using prior knowledge of internal log defects. Although CT imaging offers a potential means of obtaining...

Spectroscopic (FT-IR, FT-Raman and UV) investigation, NLO, NBO, molecular orbital and MESP analysis of 2-{2-[(2,6-dichlorophenyl)amino]phenyl}acetic acid

NASA Astrophysics Data System (ADS)

Govindasamy, P.; Gunasekaran, S.

2015-02-01

In this work, FT-IR and FT-Raman spectra of 2-{2-[(2,6-dichlorophenyl)amino]phenyl}acetic acid (abbreviated as 2DCPAPAA) have been reported in the regions 4000-450 cm-1 and 4000-50 cm-1, respectively. The molecular structure, geometry optimization, intensities, vibrational frequencies were obtained by the ab initio and DFT levels of theory B3LYP with 6-311++G(d,p) standard basis set and a different scaling of the calculated wave numbers. The complete vibrational assignments were performed on the basis of the potential energy distribution (PED) of the vibrational modes calculated using vibrational energy distribution analysis (VEDA 4) program. The harmonic frequencies were calculated and the scaled values were compared with experimental FT-IR and FT-Raman data. The observed and the calculated frequencies are found to be in good agreement. Stability of the molecule arising from hyper conjugative interactions, charge delocalization has been analyzed using natural bond orbital (NBO) analysis. The thermodynamic properties of the title compound at different temperature reveal the correlations between standard heat capacities (C) standard entropies (S) standard enthalpy changes (ΔH). The important non-linear optical properties such as electric dipole momentum, polarizability and first hyperpolarizability of 2DCPAPAA have been computed using B3LYP/6-311++G(d,p) quantum chemical calculations. The Natural charges, HOMO, LUMO, chemical hardness (η), chemical potential (μ), Electro negativity (χ) and electrophilicity values (ω) are calculated and reported. The oscillator's strength, wave length, and energy calculated by TD-DFT and 2DCPAPAA is approach complement with the experimental findings. The molecular electrostatic potential (MESP) surfaces of the molecule were constructed.

Spectroscopic (FT-IR, FT-Raman and UV) investigation, NLO, NBO, molecular orbital and MESP analysis of 2-{2-[(2,6-dichlorophenyl)amino]phenyl}acetic acid.

PubMed

Govindasamy, P; Gunasekaran, S

2015-02-05

In this work, FT-IR and FT-Raman spectra of 2-{2-[(2,6-dichlorophenyl)amino]phenyl}acetic acid (abbreviated as 2DCPAPAA) have been reported in the regions 4000-450cm(-1) and 4000-50cm(-1), respectively. The molecular structure, geometry optimization, intensities, vibrational frequencies were obtained by the ab initio and DFT levels of theory B3LYP with 6-311++G(d,p) standard basis set and a different scaling of the calculated wave numbers. The complete vibrational assignments were performed on the basis of the potential energy distribution (PED) of the vibrational modes calculated using vibrational energy distribution analysis (VEDA 4) program. The harmonic frequencies were calculated and the scaled values were compared with experimental FT-IR and FT-Raman data. The observed and the calculated frequencies are found to be in good agreement. Stability of the molecule arising from hyper conjugative interactions, charge delocalization has been analyzed using natural bond orbital (NBO) analysis. The thermodynamic properties of the title compound at different temperature reveal the correlations between standard heat capacities (C) standard entropies (S) standard enthalpy changes (ΔH). The important non-linear optical properties such as electric dipole momentum, polarizability and first hyperpolarizability of 2DCPAPAA have been computed using B3LYP/6-311++G(d,p) quantum chemical calculations. The Natural charges, HOMO, LUMO, chemical hardness (η), chemical potential (μ), Electro negativity (χ) and electrophilicity values (ω) are calculated and reported. The oscillator's strength, wave length, and energy calculated by TD-DFT and 2DCPAPAA is approach complement with the experimental findings. The molecular electrostatic potential (MESP) surfaces of the molecule were constructed. Copyright © 2014 Elsevier B.V. All rights reserved.

Extracting biomolecule collision cross sections from the high-resolution FT-ICR mass spectral linewidths.

PubMed

Jiang, Ting; Chen, Yu; Mao, Lu; Marshall, Alan G; Xu, Wei

2016-01-14

It is known that the ion collision cross section (CCS) may be calculated from the linewidth of a Fourier transform ion cyclotron resonance (FT-ICR) mass spectral peak at elevated pressure (e.g., ∼10(-6) Torr). However, the high mass resolution of FT-ICR is sacrificed in those experiments due to high buffer gas pressure. In this study, we describe a linewidth correction method to eliminate the windowing-induced peak broadening effect. Together with the energetic ion-neutral collision model previously developed by our group, this method enables the extraction of CCSs of biomolecules from high-resolution FT-ICR mass spectral linewidths, obtained at a typical operating buffer gas pressure of modern FT-ICR instruments (∼10(-10) Torr). CCS values of peptides including MRFA, angiotensin I, and bradykinin measured by the proposed method agree well with ion mobility measurements, and the unfolding of protein ions (ubiquitin) at higher charge states is also observed.

Evaluation of the stability of gas hydrates in Northern Alaska

USGS Publications Warehouse

Kamath, A.; Godbole, S.P.; Ostermann, R.D.; Collett, T.S.

1987-01-01

The factors which control the distribution of in situ gas hydrate deposits in colder regions such as Northern Alaska include; mean annual surface temperatures (MAST), geothermal gradients above and below the base of permafrost, subsurface pressures, gas composition, pore-fluid salinity and the soil condition. Currently existing data on the above parameters for the forty-six wells located in Northern Alaska were critically examined and used in calculations of depths and thicknesses of gas hydrate stability zones. To illustrate the effect of gas hydrate stability zones, calculations were done for a variable gas composition using the thermodynamic model of Holder and John (1982). The hydrostatic pressure gradient of 9.84 kPa/m (0.435 lbf/in2ft), the salinity of 10 parts per thousand (ppt) and the coarse-grained soil conditions were assumed. An error analysis was performed for the above parameters and the effect of these parameters on hydrate stability zone calculations were determined. After projecting the hydrate stability zones for the forty-six wells, well logs were used to identify and to obtain values for the depth and thickness of hydrate zones. Of the forty-six wells, only ten wells showed definite evidence of the presence of gas hydrates. ?? 1987.

Impact of Room Location on UV-C Irradiance and UV-C Dosage and Antimicrobial Effect Delivered by a Mobile UV-C Light Device.

PubMed

Boyce, John M; Farrel, Patricia A; Towle, Dana; Fekieta, Renee; Aniskiewicz, Michael

2016-06-01

OBJECTIVE To evaluate ultraviolet C (UV-C) irradiance, UV-C dosage, and antimicrobial effect achieved by a mobile continuous UV-C device. DESIGN Prospective observational study. METHODS We used 6 UV light sensors to determine UV-C irradiance (W/cm2) and UV-C dosage (µWsec/cm2) at various distances from and orientations relative to the UV-C device during 5-minute and 15-minute cycles in an ICU room and a surgical ward room. In both rooms, stainless-steel disks inoculated with methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Enterococcus (VRE), and Clostridium difficile spores were placed next to sensors, and UV-C dosages and log10 reductions of target organisms achieved during 5-minute and 15-minute cycles were determined. Mean irradiance and dosage readings were compared using ANOVA. RESULTS Mean UV-C irradiance was nearly 1.0E-03 W/cm2 in direct sight at a distance of 1.3 m (4 ft) from the device but was 1.12E-05 W/cm2 on a horizontal surface in a shaded area 3.3 m (10 ft) from the device (P4 to 1-3 for MRSA, >4 to 1-2 for VRE and >4 to 0 log10 for C. difficile spores, depending on the distance from, and orientation relative to, the device with 5-minute and 15-minute cycles. CONCLUSION UV-C irradiance, dosage, and antimicrobial effect received from a mobile UV-C device varied substantially based on location in a room relative to the UV-C device. Infect Control Hosp Epidemiol 2016;37:667-672.

Initial Results of Gulf of Mexico Gas Hydrate Joint Industry Program Leg II Logging-While-Drilling Operations

NASA Astrophysics Data System (ADS)

Boswell, R. M.; Collett, T. S.; Frye, M.; McConnell, D.; Shedd, W.; Shelander, D.; Dai, J.; Mrozewski, S.; Guerin, G.; Cook, A.; Dufrene, R.; Godfriaux, P. D.; Roy, R.; Jones, E.

2009-12-01

The Gulf of Mexico gas hydrates Joint Industry Project (the JIP), a cooperative research program between the US Department of Energy and an international industrial consortium under the leadership of Chevron, conducted its “Leg II” logging-while-drilling operations in April and May of 2009. JIP Leg II was intended to expand the existing JIP work from previous emphasis on fine-grained sedimentary systems to the direct evaluation of gas hydrate in sand-dominated reservoirs. The selection of the locations for the JIP Leg II drilling were the result of a geological and geophysical prospecting approach that integrated direct geophysical evidence of gas hydrate-bearing strata with evidence of gas sourcing and migration and occurrence of sand reservoirs within the gas hydrate stability zone. Logging-while-drilling operations included the drilling of seven wells at three sites. The expedition experienced minimal operational problems with the advanced LWD tool string, and successfully managed a number of shallow drilling challenges, including borehole breakouts, and shallow gas and water flows. Two wells drilled in Walker Ridge block 313 (WR-313) confirmed the pre-drill predictions by discovering gas hydrates at high saturations in multiple sand horizons with reservoir thicknesses up to 50 ft. In addition, drilling in WR-313 discovered a thick, strata-bound interval of grain-displacing gas hydrate in shallow fine-grained sediments. Two of three wells drilled in Green Canyon block 955 (GC-955) confirmed the pre-drill prediction of extensive sand occurrence with gas hydrate fill along the crest of a structure with positive indications of gas source and migration. In particular, well GC955-H discovered ~100 ft of gas hydrate in sand at high saturations. Two wells drilled in Alaminos Canyon block 21 (AC-21) confirmed the pre-drill prediction of potential extensive occurrence of gas hydrates in shallow sand reservoirs at low to moderate saturations; however, further data collection and analyses at AC-21 will be needed to better understand the nature of the pore filling material. JIP Leg II fully met its scientific objectives with the collection of abundant high-quality data from gas hydrate bearing sands in the Gulf of Mexico. Ongoing work within the JIP will enable further validation of the geophysical and geological methods used to predict the occurrence of gas hydrate. Expedition results will also support the selection of locations for future JIP drilling, logging and coring operations.

Near-infrared diffuse reflection systems for chlorophyll content of tomato leaves measurement

NASA Astrophysics Data System (ADS)

Jiang, Huanyu; Ying, Yibin; Lu, Huishan

2006-10-01

In this study, two measuring systems for chlorophyll content of tomato leaves were developed based on near-infrared spectral techniques. The systems mainly consists of a FT-IR spectrum analyzer, optic fiber diffuses reflection accessories and data card. Diffuse reflectance of intact tomato leaves was measured by an optics fiber optic fiber diffuses reflection accessory and a smart diffuses reflection accessory. Calibration models were developed from spectral and constituent measurements. 90 samples served as the calibration sets and 30 samples served as the validation sets. Partial least squares (PLS) and principal component regression (PCR) technique were used to develop the prediction models by different data preprocessing. The best model for chlorophyll content had a high correlation efficient of 0.9348 and a low standard error of prediction RMSEP of 4.79 when we select full range (12500-4000 cm -1), MSC path length correction method by the log(1/R). The results of this study suggest that FT-NIR method can be feasible to detect chlorophyll content of tomato leaves rapidly and nondestructively.

Maps showing mines, quarries, prospects, and exposures in the Cheat Mountain Roadless Area, Randolph County, West Virginia

USGS Publications Warehouse

Behum, Paul T.; Hammack, Richard W.

1981-01-01

Physiographically, the Cheat Mountain Roadless Area is in the Allegheny Mountain section of the Appalachian Plateaus province and is situated at the eastern edge of the Appalachian coal region. Cheat Mountain, a northeast-trending ridge, is bordered on the west by the right fork of Files Creek and on the east by Shavers Fork and its tributaries. Most of the area occupies an elevated plateau capped by resistant sandstone and conglomerate. Altitudes range form 2,320 ft on Lime Kiln Run to more than 3,900 ft on Cheat Mountain. The topography ranges from relatively flat in the uplands to very steep in the canyons along tributaries of Shavers Fork. The area is heavily forested with vegetation varying from mixed hardwoods on the western slope of Cheat Mountain to thickets of conifers in the uplands. Hemlocks are sparsely interspersed and red spruce, the dominant tree at higher elevations prior to logging in the mid 1920's, is again reforesting upland areas. Rhododendron and laurel flourish in moist protected areas along drainage courses and in coves.

Summary of hydraulic properties of the Floridan Aquifer system in coastal Georgia and adjacent parts of South Carolina and Florida

USGS Publications Warehouse

Clarke, John S.; Leeth, David C.; Taylor-Harris, DaVette; Painter, Jaime A.; Labowski, James L.

2005-01-01

Hydraulic-property data for the Floridan aquifer system and equivalent clastic sediments in a 67-county area of coastal Georgia and adjacent parts of South Carolina and Florida were evaluated to provide data necessary for development of ground-water flow and solute-transport models. Data include transmissivity at 324 wells, storage coefficient at 115 wells, and vertical hydraulic conductivity of 72 core samples from 27 sites. Hydraulic properties of the Upper Floridan aquifer vary greatly in the study area due to the heterogeneity (and locally to anisotropy) of the aquifer and to variations in the degree of confinement provided by confining units. Prominent structural features in the areathe Southeast Georgia Embayment, the Beaufort Arch, and the Gulf Troughinfluence the thickness and hydraulic properties of the sediments comprising the Floridan aquifer system. Transmissivity of the Upper Floridan aquifer and equivalent updip units was compiled for 239 wells and ranges from 530 feet squared per day (ft2/d) at Beaufort County, South Carolina, to 600,000 ft2/d in Coffee County, Georgia. In carbonate rock settings of the lower Coastal Plain, transmissivity of the Upper Floridan aquifer generally is greater than 20,000 ft2/d, with values exceeding 100,000 ft2/d in the southeastern and southwestern parts of the study area (generally coinciding with the area of greatest aquifer thickness). Transmissivity of the Upper Floridan aquifer generally is less than 10,000 ft2/d in and near the upper Coastal Plain, where the aquifer is thin and consists largely of clastic sediments, and in the vicinity of the Gulf Trough, where the aquifer consists of low permeability rocks and sediments. Large variability in the range of transmissivity in Camden and Glynn Counties, Georgia, and Nassau County, Florida, demonstrates the anisotropic distribution of hydraulic properties that may result from fractures or solution openings in the carbonate rocks. Storage coefficient of the Upper Floridan aquifer was compiled for 106 wells and ranges from about 0.00004 at Beaufort County, South Carolina, to 0.04 in Baker County, Florida. Transmissivity of the Lower Floridan aquifer and equivalent updip clastic units was compiled for 53 wells and ranges from about 170 ft2/d in Barnwell County, South Carolina, to about 43,000 ft2/d in Camden County, Georgia. Transmissivity of the Lower Floridan aquifer is greatest where the aquifer is thickest in southeastern Georgia and northeastern Floridawhere estimates are greater than 10,000 ft2/d; at one well in southeastern Georgia transmissivity was estimated to be as high as 200,000 ft2/d. Storage-coefficient data for the Lower Floridan aquifer are limited to three estimates in Barnwell and Allendale Counties, South Carolina, and to estimates determined from six multi-aquifer tests in Duval County, Florida. In the South Carolina tests, storage coefficient ranges from 0.0003 to 0.0004; this range is indicative of a confined aquifer. The storage coefficient for the combined Upper and Lower Floridan wells in Duval County, Florida, ranges from 0.00002 to 0.02. Vertical hydraulic conductivity was compiled from core samples collected at 27 sites. For the Upper Floridan confining unit, values from 39 core samples at 17 sites range from 0.0002 to 3 feet per day (ft/d). For the Lower Floridan confining unit, values from 10 core samples at 9 sites range from about 0.000004 to 0.16 ft/d. Vertical hydraulic conductivity of the Upper Floridan aquifer was compiled from 16 core samples at five sites, mostly in the Brunswick, Georgia, area and values range from 0.00134 to 160.4 ft/d. Vertical hydraulic conductivity for the semiconfining unit separating the upper and lower water-bearing zones of the Upper Floridan at Brunswick, Georgia, compiled from 6 core samples at three sites ranges from 0.000008 to 0.000134 ft/d. The vertical hydraulic conductivity of the Lower Floridan aquifer in a core sample from a well at Brunswick, G

The application of the sinusoidal model to lung cancer patient respiratory motion

DOE Office of Scientific and Technical Information (OSTI.GOV)

George, R.; Vedam, S.S.; Chung, T.D.

2005-09-15

Accurate modeling of the respiratory cycle is important to account for the effect of organ motion on dose calculation for lung cancer patients. The aim of this study is to evaluate the accuracy of a respiratory model for lung cancer patients. Lujan et al. [Med. Phys. 26(5), 715-720 (1999)] proposed a model, which became widely used, to describe organ motion due to respiration. This model assumes that the parameters do not vary between and within breathing cycles. In this study, first, the correlation of respiratory motion traces with the model f(t) as a function of the parameter n(n=1,2,3) was undertakenmore » for each breathing cycle from 331 four-minute respiratory traces acquired from 24 lung cancer patients using three breathing types: free breathing, audio instruction, and audio-visual biofeedback. Because cos{sup 2} and cos{sup 4} had similar correlation coefficients, and cos{sup 2} and cos{sup 1} have a trigonometric relationship, for simplicity, the cos{sup 1} value was consequently used for further analysis in which the variations in mean position (z{sub 0}), amplitude of motion (b) and period ({tau}) with and without biofeedback or instructions were investigated. For all breathing types, the parameter values, mean position (z{sub 0}), amplitude of motion (b), and period ({tau}) exhibited significant cycle-to-cycle variations. Audio-visual biofeedback showed the least variations for all three parameters (z{sub 0}, b, and {tau}). It was found that mean position (z{sub 0}) could be approximated with a normal distribution, and the amplitude of motion (b) and period ({tau}) could be approximated with log normal distributions. The overall probability density function (pdf) of f(t) for each of the three breathing types was fitted with three models: normal, bimodal, and the pdf of a simple harmonic oscillator. It was found that the normal and the bimodal models represented the overall respiratory motion pdfs with correlation values from 0.95 to 0.99, whereas the range of the simple harmonic oscillator pdf correlation values was 0.71 to 0.81. This study demonstrates that the pdfs of mean position (z{sub 0}), amplitude of motion (b), and period ({tau}) can be used for sampling to obtain more realistic respiratory traces. The overall standard deviations of respiratory motion were 0.48, 0.57, and 0.55 cm for free breathing, audio instruction, and audio-visual biofeedback, respectively.« less

Graphene base heterojunction transistor: An explorative study on device potential, optimization, and base parasitics

NASA Astrophysics Data System (ADS)

Di Lecce, Valerio; Grassi, Roberto; Gnudi, Antonio; Gnani, Elena; Reggiani, Susanna; Baccarani, Giorgio

2015-12-01

The Graphene-Base Heterojunction Transistor (GBHT) is a novel device concept with a high potential for analog high-frequency RF operation, in which the current is due to both thermionic emission and tunneling. In this paper we study through numerical simulations the influence of previously uninvestigated aspects of Si- and Ge-based GBHTs-namely, crystallographic orientation and doping density values-on the device performance; a comparison with an aggressively scaled HBT structure is then reported. The simulations are carried out with an in-house developed code based on a 1-D quantum transport model within the effective mass approximation and the assumptions of ballistic transport with non-parabolic corrections and ideal semiconductor-graphene interface. We show that crystallographic orientation has a negligible effect on the GBHT performance. The doping density values in the GBHT emitter and collector regions can be tailored to maximize the device performance: the Si device shows better overall performance than the Ge one, yielding a peak cut-off frequency fT higher than 4 THz together with an intrinsic voltage gain above 10, or even higher fT at the cost of a lower gain. The Si-based GBHT can potentially outperform the SiGe HBT by a 2.8 higher fT . For a Si-based GBHT with a circular active region of diameter 50-100 nm, a theoretical balanced value for fT and fmax above 2 THz can be achieved, provided the base parasitics are carefully minimized.

Application of reflectance colorimeter measurements and infrared spectroscopy methods to rapid and nondestructive evaluation of carotenoids content in apricot (Prunus armeniaca L.).

PubMed

Ruiz, David; Reich, Maryse; Bureau, Sylvie; Renard, Catherine M G C; Audergon, Jean-Marc

2008-07-09

The importance of carotenoid content in apricot (Prunus armeniaca L.) is recognized not only because of the color that they impart but also because of their protective activity against human diseases. Current methods to assess carotenoid content are time-consuming, expensive, and destructive. In this work, the application of rapid and nondestructive methods such as colorimeter measurements and infrared spectroscopy has been evaluated for carotenoid determination in apricot. Forty apricot genotypes covering a wide range of peel and flesh colors have been analyzed. Color measurements on the skin and flesh ( L*, a*, b*, hue, chroma, and a*/ b* ratio) as well as Fourier transform near-infrared spectroscopy (FT-NIR) on intact fruits and Fourier transform mid-infrared spectroscopy (FT-MIR) on ground flesh were correlated with the carotenoid content measured by high-performance liquid chromatography. A high variability in color values and carotenoid content was observed. Partial least squares regression analyses between beta-carotene content and provitamin A activity and color measurements showed a high fit in peel, flesh, and edible apricot portion (R(2) ranged from 0.81 to 0.91) and low prediction error. Regression equations were developed for predicting carotenoid content by using color values, which appeared as a simple, rapid, reliable, and nondestructive method. However, FT-NIR and FT-MIR models showed very low R(2) values and very high prediction errors for carotenoid content.

Prediction of essential oil content of oregano by hand-held and Fourier transform NIR spectroscopy.

PubMed

Camps, Cédric; Gérard, Marianne; Quennoz, Mélanie; Brabant, Cécile; Oberson, Carine; Simonnet, Xavier

2014-05-01

In the framework of a breeding programme, the analysis of hundreds of oregano samples to determine their essential oil content (EOC) is time-consuming and expensive in terms of labour. Therefore developing a new method that is rapid, accurate and less expensive to use would be an asset to breeders. The aim of the present study was to develop a method based on near-inrared (NIR) spectroscopy to determine the EOC of oregano dried powder. Two spectroscopic approaches were compared, the first using a hand-held NIR device and the second a Fourier transform (FT) NIR spectrometer. Hand-held NIR (1000-1800 nm) measurements and partial least squares regression allowed the determination of EOC with R² and SEP values of 0.58 and 0.81 mL per 100 g dry matter (DM) respectively. Measurements with FT-NIR (1000-2500 nm) allowed the determination of EOC with R² and SEP values of 0.91 and 0.68 mL per 100 g DM respectively. RPD, RER and RPIQ values for the model implemented with FT-NIR data were satisfactory for screening application, while those obtained with hand-held NIR data were below the level required to consider the model as enough accurate for screening application. The FT-NIR approach allowed the development of an accurate model for EOC prediction. Although the hand-held NIR approach is promising, it needs additional development before it can be used in practice. © 2013 Society of Chemical Industry.

Procedural revision to the use-dilution methods: establishment of maximum log density value for test microbes on inoculated carriers.

PubMed

Tomasino, Stephen F; Pines, Rebecca M; Hamilton, Gordon C

2012-01-01

(Staphylococcus aureus) and 964.02 (Pseudomonas aeruginosa), were revised in 2009 to include a standardized procedure to measure the log density of the test microbe and to establish a minimum mean log density value of 6.0 (geometric mean of 1.0 x 10(6) CFU/carrier) to qualify the test results. This report proposes setting a maximum mean log density value of 7.0 (geometric mean of 1.0 x 10(7) CFU/carrier) to further standardize the procedure. The minimum value was based on carrier count data collected by four laboratories over an 8-year period (1999-2006). The data have been updated to include an additional 4 years' worth of data (2006-2010) collected by the same laboratories. A total of 512 tests were conducted on products bearing claims against P. aeruginosa and S. aureus with and without an organic soil load (OSL) added to the inoculum (as specified on the product label claim). Six carriers were assayed in each test, for a total of 3072 carriers. Mean log densities for each of the 512 tests were at least 6.0. With the exception of two tests, one for P. aeruginosa without OSL and one for S. aureus with OSL, the mean log densities did not exceed 7.5 (geometric mean of 3.2 x 10(7) CFU/carrier). Across microbes and OSL treatments, the mean log density (+/- SEM) was 6.80 (+/- 0.07) per carrier (a geometric mean of 6.32 x 10(6) CFUlcarrier) and acceptable repeatability (0.28) and reproducibility (0.31) SDs were exhibited. A maximum mean log density per carrier of 7.0 is being proposed here as a validity requirement for S. aureus and P. aeruginosa. A modification to the method to allow for dilution of the final test cultures to achieve carrier counts within 6.0-7.0 logs is also being proposed. Establishing a range of 6.0-7.0 logs will help improve the reliability of the method and should allow for more consistent results within and among laboratories.

Temporal Decay in Timber Species Composition and Value in Amazonian Logging Concessions.

PubMed

Richardson, Vanessa A; Peres, Carlos A

2016-01-01

Throughout human history, slow-renewal biological resource populations have been predictably overexploited, often to the point of economic extinction. We assess whether and how this has occurred with timber resources in the Brazilian Amazon. The asynchronous advance of industrial-scale logging frontiers has left regional-scale forest landscapes with varying histories of logging. Initial harvests in unlogged forests can be highly selective, targeting slow-growing, high-grade, shade-tolerant hardwood species, while later harvests tend to focus on fast-growing, light-wooded, long-lived pioneer trees. Brazil accounts for 85% of all native neotropical forest roundlog production, and the State of Pará for almost half of all timber production in Brazilian Amazonia, the largest old-growth tropical timber reserve controlled by any country. Yet the degree to which timber harvests beyond the first-cut can be financially profitable or demographically sustainable remains poorly understood. Here, we use data on legally planned logging of ~17.3 million cubic meters of timber across 314 species extracted from 824 authorized harvest areas in private and community-owned forests, 446 of which reported volumetric composition data by timber species. We document patterns of timber extraction by volume, species composition, and monetary value along aging eastern Amazonian logging frontiers, which are then explained on the basis of historical and environmental variables. Generalized linear models indicate that relatively recent logging operations farthest from heavy-traffic roads are the most selective, concentrating gross revenues on few high-value species. We find no evidence that the post-logging timber species composition and total value of forest stands recovers beyond the first-cut, suggesting that the commercially most valuable timber species become predictably rare or economically extinct in old logging frontiers. In avoiding even more destructive land-use patterns, managing yields of selectively-logged forests is crucial for the long-term integrity of forest biodiversity and financial viability of local industries. The logging history of eastern Amazonian old-growth forests likely mirrors unsustainable patterns of timber depletion over time in Brazil and other tropical countries.

Temporal Decay in Timber Species Composition and Value in Amazonian Logging Concessions

PubMed Central

Peres, Carlos A.

2016-01-01

Throughout human history, slow-renewal biological resource populations have been predictably overexploited, often to the point of economic extinction. We assess whether and how this has occurred with timber resources in the Brazilian Amazon. The asynchronous advance of industrial-scale logging frontiers has left regional-scale forest landscapes with varying histories of logging. Initial harvests in unlogged forests can be highly selective, targeting slow-growing, high-grade, shade-tolerant hardwood species, while later harvests tend to focus on fast-growing, light-wooded, long-lived pioneer trees. Brazil accounts for 85% of all native neotropical forest roundlog production, and the State of Pará for almost half of all timber production in Brazilian Amazonia, the largest old-growth tropical timber reserve controlled by any country. Yet the degree to which timber harvests beyond the first-cut can be financially profitable or demographically sustainable remains poorly understood. Here, we use data on legally planned logging of ~17.3 million cubic meters of timber across 314 species extracted from 824 authorized harvest areas in private and community-owned forests, 446 of which reported volumetric composition data by timber species. We document patterns of timber extraction by volume, species composition, and monetary value along aging eastern Amazonian logging frontiers, which are then explained on the basis of historical and environmental variables. Generalized linear models indicate that relatively recent logging operations farthest from heavy-traffic roads are the most selective, concentrating gross revenues on few high-value species. We find no evidence that the post-logging timber species composition and total value of forest stands recovers beyond the first-cut, suggesting that the commercially most valuable timber species become predictably rare or economically extinct in old logging frontiers. In avoiding even more destructive land-use patterns, managing yields of selectively-logged forests is crucial for the long-term integrity of forest biodiversity and financial viability of local industries. The logging history of eastern Amazonian old-growth forests likely mirrors unsustainable patterns of timber depletion over time in Brazil and other tropical countries. PMID:27410029

Fragment-based approach to calculate hydrophobicity of anionic and nonionic surfactants derived from chromatographic retention on a C18 stationary phase.

PubMed

Hammer, Jort; Haftka, Joris J-H; Scherpenisse, Peter; Hermens, Joop L M; de Voogt, Pim W P

2017-02-01

To predict the fate and potential effects of organic contaminants, information about their hydrophobicity is required. However, common parameters to describe the hydrophobicity of organic compounds (e.g., octanol-water partition constant [K OW ]) proved to be inadequate for ionic and nonionic surfactants because of their surface-active properties. As an alternative approach to determine their hydrophobicity, the aim of the present study was therefore to measure the retention of a wide range of surfactants on a C 18 stationary phase. Capacity factors in pure water (k' 0 ) increased linearly with increasing number of carbon atoms in the surfactant structure. Fragment contribution values were determined for each structural unit with multilinear regression, and the results were consistent with the expected influence of these fragments on the hydrophobicity of surfactants. Capacity factors of reference compounds and log K OW values from the literature were used to estimate log K OW values for surfactants (log KOWHPLC). These log KOWHPLC values were also compared to log K OW values calculated with 4 computational programs: KOWWIN, Marvin calculator, SPARC, and COSMOThermX. In conclusion, capacity factors from a C 18 stationary phase are found to better reflect hydrophobicity of surfactants than their K OW values. Environ Toxicol Chem 2017;36:329-336. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC.

Combined training (strength plus aerobic) potentiates a reduction in body fat but only functional training reduced low-density lipoprotein cholesterol in postmenopausal women with a similar training load.

PubMed

Rossi, Fabrício Eduardo; Fortaleza, Ana Claudia S; Neves, Lucas M; Diniz, Tiego A; de Castro, Marcela R; Buonani, Camila; Mota, Jorge; Freitas, Ismael F

2017-06-01

The aim of this study was to compare the effects of combined (CT; strength plus aerobic) and functional training (FT) on the body composition and metabolic profile with a similar training load in postmenopausal women. The participants were divided into three groups: CT (n=20), FT (n=17), and control group (CG, n=15). The trunk FM, fat mass (FM), percentage of FM (FM%), and fat-free mass were estimated by dual-energy X-ray absorptiometry. The metabolic profile, glucose, triacylglycerol, total cholesterol, high-density lipoprotein cholesterol and low-density lipoprotein cholesterol (LDL-c) were assessed. There were main effects of time in trunk fat, FM, and FM% ( P <0.05). There were statistically significant interaction for FM ( P =0.015), FM% ( P =0.017) with lower values for CT group. For LDL-c, there was significant interaction ( P =0.002) with greater values for FT group in relation to CG and CT. Furthermore, when performed the post hoc test on the "mean absolute differences" (Δ), it can observed statistically significant difference between FT, CT, and CG (-13.0±16.5 mg/dL vs. 4.8±18.4 mg/dL vs. 9.2±18.8 mg/dL, P <0.05). In conclusion, when training loads are equivalent CT potentiated a reduction in FM and FM%, however, only FT reduced LDL-c in postmenopausal women.

Discrimination and prediction of the origin of Chinese and Korean soybeans using Fourier transform infrared spectrometry (FT-IR) with multivariate statistical analysis

PubMed Central

Lee, Byeong-Ju; Zhou, Yaoyao; Lee, Jae Soung; Shin, Byeung Kon; Seo, Jeong-Ah; Lee, Doyup; Kim, Young-Suk

2018-01-01

The ability to determine the origin of soybeans is an important issue following the inclusion of this information in the labeling of agricultural food products becoming mandatory in South Korea in 2017. This study was carried out to construct a prediction model for discriminating Chinese and Korean soybeans using Fourier-transform infrared (FT-IR) spectroscopy and multivariate statistical analysis. The optimal prediction models for discriminating soybean samples were obtained by selecting appropriate scaling methods, normalization methods, variable influence on projection (VIP) cutoff values, and wave-number regions. The factors for constructing the optimal partial-least-squares regression (PLSR) prediction model were using second derivatives, vector normalization, unit variance scaling, and the 4000–400 cm–1 region (excluding water vapor and carbon dioxide). The PLSR model for discriminating Chinese and Korean soybean samples had the best predictability when a VIP cutoff value was not applied. When Chinese soybean samples were identified, a PLSR model that has the lowest root-mean-square error of the prediction value was obtained using a VIP cutoff value of 1.5. The optimal PLSR prediction model for discriminating Korean soybean samples was also obtained using a VIP cutoff value of 1.5. This is the first study that has combined FT-IR spectroscopy with normalization methods, VIP cutoff values, and selected wave-number regions for discriminating Chinese and Korean soybeans. PMID:29689113

CRYPTOSPORIDIUM LOG INACTIVATION CALCULATION METHODS

EPA Science Inventory

Appendix O of the Surface Water Treatment Rule (SWTR) Guidance Manual introduces the CeffT10 (i.e., reaction zone outlet C value and T10 time) method for calculating ozone CT value and Giardia and virus log inactivation. The LT2ESWTR Pre-proposal Draft Regulatory Language for St...

A CORRELATION BETWEEN RADIATION TOLERANCE AND NUCLEAR SURFACE AREA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iversen, S.

1962-09-22

Sparrow and Miksche (Science, 134:282) determined the dose (r/day) required to produce severe growth inhibition in 23 species of plants and found a linear relationship between log nuclear volume and log dose. The following equations hold for 6 species: log nuclear volume - 4.42 -0.82 log dose and log nuclear volume = 1.66 + 0.66 log (DNA content). If all the nuclear DNA is distributed in two peripheral zones, the equations also hold: 2(log nuclear surface area) - 1.33(log nuclear volume) - 2.21 + 0.88 log(DNA content) and 5.88-- 1.09 log dose. For the 23 species, the equation was obtained:more » 2(log nuclear surface area) = 5.41 -- 0.97 log dose. All the slopes are close to the expected value of 1.00. (D.L.C.)« less

Structural study, NCA, FT-IR, FT-Raman spectral investigations, NBO analysis, thermodynamic functions of N-acetyl-l-phenylalanine.

PubMed

Raja, B; Balachandran, V; Revathi, B

2015-03-05

The FT-IR and FT-Raman spectra of N-acetyl-l-phenylalanine were recorded and analyzed. Natural bond orbital analysis has been carried out for various intramolecular interactions that are responsible for the stabilization of the molecule. HOMO-LUMO energy gap has been computed with the help of density functional theory. The statistical thermodynamic functions (heat capacity, entropy, vibrational partition function and Gibbs energy) were obtained for the range of temperature 100-1000K. The polarizability, first hyperpolarizability, anisotropy polarizability invariant has been computed using quantum chemical calculations. The infrared and Raman spectra were also predicted from the calculated intensities. Comparison of the experimental and theoretical spectra values provides important information about the ability of the computational method to describe the vibrational modes. Copyright © 2014 Elsevier B.V. All rights reserved.

A method for accelerated trait conversion in plant breeding.

PubMed

Lewis, Ramsey S; Kernodle, S P

2009-05-01

Backcrossing is often used in cultivar development to transfer one or a few genes to desired genetic backgrounds. The duration necessary to complete such 'trait conversions' is largely dependent upon generation times. Constitutive overexpression of the Arabidopsis thaliana gene FT (FLOWERING LOCUS T) induces early-flowering in many plants. Here, we used tobacco (Nicotiana tabacum L.) as a model system to propose and examine aspects of a modified backcross procedure where transgenic FT overexpression is used to reduce generation time and accelerate gene transfer. In this method, the breeder would select for an FT transgene insertion and the trait(s) of interest at each backcross generation except the last. In the final generation, selection would be conducted for the trait(s) of interest, but against FT, to generate the backcross-derived trait conversion. We demonstrate here that constitutive FT overexpression functions to dramatically reduce days-to-flower similarly in diverse tobacco genetic backgrounds. FT-containing plants flowered in an average of 39 days, in comparison with 87-138 days for non-FT plants. Two FT transgene insertions were found to segregate independently of several disease resistance genes often the focus of backcrossing in tobacco. In addition, no undesirable epigenetic effects on flowering time were observed once FT was segregated away. The proposed system would reduce the time required to complete a trait conversion in tobacco by nearly one-half. These features suggest the possible value of this modified backcrossing system for tobacco or other crop species where long generation times or photoperiod sensitivity may impede timely trait conversion.

Temperature-pressure conditions in coalbed methane reservoirs of the Black Warrior basin: Implications for carbon sequestration and enhanced coalbed methane recovery

USGS Publications Warehouse

Pashin, J.C.; McIntyre, M.R.

2003-01-01

Sorption of gas onto coal is sensitive to pressure and temperature, and carbon dioxide can be a potentially volatile supercritical fluid in coalbed methane reservoirs. More than 5000 wells have been drilled in the coalbed methane fields of the Black Warrior basin in west-central Alabama, and the hydrologic and geothermic information from geophysical well logs provides a robust database that can be used to assess the potential for carbon sequestration in coal-bearing strata.Reservoir temperature within the coalbed methane target zone generally ranges from 80 to 125 ??F (27-52 ??C), and geothermal gradient ranges from 6.0 to 19.9 ??F/1000 ft (10.9-36.2 ??C/km). Geothermal gradient data have a strong central tendency about a mean of 9.0 ??F/1000 ft (16.4 ??C/km). Hydrostatic pressure gradients in the coalbed methane fields range from normal (0.43 psi/ft) to extremely underpressured (<0.05 psi/ft). Pressure-depth plots establish a bimodal regime in which 70% of the wells have pressure gradients greater than 0.30 psi/ft, and 20% have pressure gradients lower than 0.10 psi/ft. Pockets of underpressure are developed around deep longwall coal mines and in areas distal to the main hydrologic recharge zone, which is developed in structurally upturned strata along the southeastern margin of the basin.Geothermal gradients within the coalbed methane fields are high enough that reservoirs never cross the gas-liquid condensation line for carbon dioxide. However, reservoirs have potential for supercritical fluid conditions beyond a depth of 2480 ft (756 m) under normally pressured conditions. All target coal beds are subcritically pressured in the northeastern half of the coalbed methane exploration fairway, whereas those same beds were in the supercritical phase window prior to gas production in the southwestern half of the fairway. Although mature reservoirs are dewatered and thus are in the carbon dioxide gas window, supercritical conditions may develop as reservoirs equilibrate toward a normal hydrostatic pressure gradient after abandonment. Coal can hold large quantities of carbon dioxide under supercritical conditions, and supercritical isotherms indicate non-Langmiur conditions under which some carbon dioxide may remain mobile in coal or may react with formation fluids or minerals. Hence, carbon sequestration and enhanced coalbed methane recovery show great promise in subcritical reservoirs, and additional research is required to assess the behavior of carbon dioxide in coal under supercritical conditions where additional sequestration capacity may exist. ?? 2003 Elsevier Science B.V. All rights reserved.

Diameter effect on stress-wave evaluation of modulus of elasticity of logs

Treesearch

Xiping Wang; Robert J. Ross; Brian K. Brashaw; John Punches; John R. Erickson; John W. Forsman; Roy E. Pellerin

2004-01-01

Recent studies on nondestructive evaluation (NDE) of logs have shown that a longitudinal stress-wave method can be used to nondestructively evaluate the modulus of elasticity (MOE) of logs. A strong relationship has been found between stress-wave MOE and static MOE of logs, but a significant deviation was observed between stress-wave and static values. The objective of...

HW Buck for Windows: the optimal hardwood log bucking decision simulator with expanded capabilities

Treesearch

James B. Pickens; Scott Noble; Blair Orr; Philip A. Araman; John E. Baumgras; Al Steele

2006-01-01

It has long been recognized that inappropriate placement of crosscuts when manufacturing hardwood logs from harvested stems (log bucking) reduces the value of logs produced. Recent studies have estimated losses in the range from 28% to 38% in the lake states region. These estimates were developed by evaluating the bucking cuts chosen by harvesting crews and comparing...

Diameter effect on stress-wave evaluation of modulus of elasticity of logs

Treesearch

Xiping Wang; Robert J. Ross; Brian K. Brashaw; John R. Erickson; John W. Forsman; Roy Pellerin

2003-01-01

Recent studies on nondestructive evaluation (NDE) of logs have shown that a longitudinal stress-wave method can be used to nondestructively evaluate the modulus of elasticity (MOE) of logs. A strong relationship has been found between stress-wave MOE and static MOE of logs, but a significant deviation was observed between stress-wave and static values. The objective of...

Computer-Generated Optimum Hardwood Log Sawing Using Internal Defect Information

Treesearch

Luis G. Occeña; Daniel L. Schmoldt

1994-01-01

The planning of how the hardwood log can be sawn to improve recovery of high-value lumber has always been hampered by the limited information provided by external defects, and whatever internal defects are eventually revealed on the cut log faces by the sawing pattern. With expanded export and domestic markets, low-quality logs, increased competition from non-wood...

Using low-grade hardwoods for CLT production: a yield analysis

Treesearch

R. Edward Thomas; Urs Buehlmann

2017-01-01

Low-grade hardwood logs are the by-product of logging operations and, more frequently today, urban tree removals. The market prices for these logs is low, as is the value recovered from their logs when producing traditional forest products such as pallet parts, railroad ties, landscaping mulch, or chips for pulp. However, the emergence of cross-laminated timber (CLT)...

Lumber values from computerized simulation of hardwood log sawing

Treesearch

D.B. Richards; W.K. Adkins; H. Hallock; E.H. Bulgrin

1980-01-01

Computer simulation sawing programs were used to study the sawing of mathematical models of hardwood logs by me live sawing and three 4-sided sawing methods. One of the 4-sided methods simulated "grade sawing" by sawing each successive board from the log face with the highest potential grade. Logs from 10 through 28 inches in diameter were sawn. In addition,...

Interspecies quantitative structure-activity relationships (QSARs) for eco-toxicity screening of chemicals: the role of physicochemical properties.

PubMed

Furuhama, A; Hasunuma, K; Aoki, Y

2015-01-01

In addition to molecular structure profiles, descriptors based on physicochemical properties are useful for explaining the eco-toxicities of chemicals. In a previous study we reported that a criterion based on the difference between the partition coefficient (log POW) and distribution coefficient (log D) values of chemicals enabled us to identify aromatic amines and phenols for which interspecies relationships with strong correlations could be developed for fish-daphnid and algal-daphnid toxicities. The chemicals that met the log D-based criterion were expected to have similar toxicity mechanisms (related to membrane penetration). Here, we investigated the applicability of log D-based criteria to the eco-toxicity of other kinds of chemicals, including aliphatic compounds. At pH 10, use of a log POW - log D > 0 criterion and omission of outliers resulted in the selection of more than 100 chemicals whose acute fish toxicities or algal growth inhibition toxicities were almost equal to their acute daphnid toxicities. The advantage of log D-based criteria is that they allow for simple, rapid screening and prioritizing of chemicals. However, inorganic molecules and chemicals containing certain structural elements cannot be evaluated, because calculated log D values are unavailable.

Accuracy testing of electric groundwater-level measurement tapes

USGS Publications Warehouse

Jelinski, Jim; Clayton, Christopher S.; Fulford, Janice M.

2015-01-01

The accuracy tests demonstrated that none of the electric-tape models tested consistently met the suggested USGS accuracy of ±0.01 ft. The test data show that the tape models in the study should give a water-level measurement that is accurate to roughly ±0.05 ft per 100 ft without additional calibration. To meet USGS accuracy guidelines, the electric-tape models tested will need to be individually calibrated. Specific conductance also plays a part in tape accuracy. The probes will not work in water with specific conductance values near zero, and the accuracy of one probe was unreliable in very high conductivity water (10,000 microsiemens per centimeter).

Prediction of drug transport processes using simple parameters and PLS statistics. The use of ACD/logP and ACD/ChemSketch descriptors.

PubMed

Osterberg, T; Norinder, U

2001-01-01

A method of modelling and predicting biopharmaceutical properties using simple theoretically computed molecular descriptors and multivariate statistics has been investigated for several data sets related to solubility, IAM chromatography, permeability across Caco-2 cell monolayers, human intestinal perfusion, brain-blood partitioning, and P-glycoprotein ATPase activity. The molecular descriptors (e.g. molar refractivity, molar volume, index of refraction, surface tension and density) and logP were computed with ACD/ChemSketch and ACD/logP, respectively. Good statistical models were derived that permit simple computational prediction of biopharmaceutical properties. All final models derived had R(2) values ranging from 0.73 to 0.95 and Q(2) values ranging from 0.69 to 0.86. The RMSEP values for the external test sets ranged from 0.24 to 0.85 (log scale).

Integrating models that depend on variable data

NASA Astrophysics Data System (ADS)

Banks, A. T.; Hill, M. C.

2016-12-01

Models of human-Earth systems are often developed with the goal of predicting the behavior of one or more dependent variables from multiple independent variables, processes, and parameters. Often dependent variable values range over many orders of magnitude, which complicates evaluation of the fit of the dependent variable values to observations. Many metrics and optimization methods have been proposed to address dependent variable variability, with little consensus being achieved. In this work, we evaluate two such methods: log transformation (based on the dependent variable being log-normally distributed with a constant variance) and error-based weighting (based on a multi-normal distribution with variances that tend to increase as the dependent variable value increases). Error-based weighting has the advantage of encouraging model users to carefully consider data errors, such as measurement and epistemic errors, while log-transformations can be a black box for typical users. Placing the log-transformation into the statistical perspective of error-based weighting has not formerly been considered, to the best of our knowledge. To make the evaluation as clear and reproducible as possible, we use multiple linear regression (MLR). Simulations are conducted with MatLab. The example represents stream transport of nitrogen with up to eight independent variables. The single dependent variable in our example has values that range over 4 orders of magnitude. Results are applicable to any problem for which individual or multiple data types produce a large range of dependent variable values. For this problem, the log transformation produced good model fit, while some formulations of error-based weighting worked poorly. Results support previous suggestions fthat error-based weighting derived from a constant coefficient of variation overemphasizes low values and degrades model fit to high values. Applying larger weights to the high values is inconsistent with the log-transformation. Greater consistency is obtained by imposing smaller (by up to a factor of 1/35) weights on the smaller dependent-variable values. From an error-based perspective, the small weights are consistent with large standard deviations. This work considers the consequences of these two common ways of addressing variable data.

Comparison of the Quantiplex Version 3.0 Assay and a Sensitized Amplicor Monitor Assay for Measurement of Human Immunodeficiency Virus Type 1 RNA Levels in Plasma Samples

PubMed Central

Highbarger, Helene C.; Alvord, W. Gregory; Jiang, Min Kang; Shah, Akram S.; Metcalf, Julia A.; Lane, H. Clifford; Dewar, Robin L.

1999-01-01

This study evaluated correlation and agreement between version 3 of the Quantiplex human immunodeficiency virus type 1 (HIV-1) RNA assay (v3 branched DNA [bDNA]) and a sensitized Amplicor HIV-1 Monitor assay (reverse transcription [RT]-PCR) for the measurement of HIV RNA. Three hundred eighteen samples from 59 randomly selected, HIV-1-seropositive persons on various drug protocols from the National Institute of Allergy and Infectious Diseases HIV outpatient clinic were studied. The results indicate that v3 bDNA and RT-PCR are highly correlated (r = 0.98) and are in good agreement (mean difference in log10 copies/ml ± 2 standard deviations = 0.072 ± 0.371). The relationship between values obtained by both assays is given by the following equation: log10v3 bDNA = −0.0915 + 1.0052 · log10RT-PCR. This represents a 1.026-fold difference between log10RT-PCR values and log10v3 bDNA values. PMID:10523562

FT3/FT4 ratio predicts non-alcoholic fatty liver disease independent of metabolic parameters in patients with euthyroidism and hypothyroidism

PubMed Central

Gökmen, Fatma Yahyaoğlu; Ahbab, Süleyman; Ataoğlu, Hayriye Esra; Türker, Betül Çavuşoğlu; Çetin, Faik; Türker, Fatih; Mamaç, Rabia Yahyaoğlu; Yenigün, Mustafa

2016-01-01

OBJECTIVE: This study was performed to evaluate the effects of metabolic parameters and thyroid dysfunction on the development of non-alcoholic fatty liver disease (NAFLD). METHODS: The current study evaluated a total of 115 patients, 75 female and 40 male. Physical examination and anthropometric measurements were applied to all participants. Hypothyroidism was considered at a thyroid stimulating hormone level ≥ 4.1 mIU/L. Patients with euthyroidism and patients with hypothyroidism were compared. Abdominal ultrasonography was used to diagnose non-alcoholic fatty liver disease. The participants were further compared with regard to the presence of non-alcoholic fatty liver disease. Logistic regression modeling was performed to identify the relationship between non-alcoholic fatty liver disease and independent variables, such as metabolic parameters and insulin resistance. RESULTS: Non-alcoholic fatty liver disease was identified in 69 patients. The mean waist circumference, body mass index, fasting plasma insulin, HOMA-IR (p<0.001) and FT3/FT4 ratio (p=0.01) values were significantly higher in the patients with NAFLD compared to those without it. Multivariate regression analysis revealed that FT3/FT4 ratio, waist circumference and insulin resistance were independent risk factors for non-alcoholic fatty liver disease. CONCLUSION: Insulin resistance, enlarged waist circumference, elevated body mass index, higher FT3/FT4 ratio and hypertriglyceridemia are independent risk factors for NADLF, whereas hypothyroidism is not directly related to the condition. PMID:27166773

Thyroid hormone elevations during acute psychiatric illness: relationship to severity and distinction from hyperthyroidism.

PubMed

Roca, R P; Blackman, M R; Ackerley, M B; Harman, S M; Gregerman, R I

1990-01-01

Acute psychiatric illness may be accompanied by transient hyperthyroxinemia. The mechanism of this phenomenon was examined by determining the role of thyrotropin (TSH) in the genesis of this state. Serial measurements of TSH, thyroxine (T4), free T4 index (FT4I), triiodothyronine (T3), and free T3 index (FT3I) were performed in 45 acutely hospitalized patients with major psychiatric disorders. Twenty-two (49%) patients exhibited significant elevations (greater than or equal to 2 SD above mean value of controls) of one or more thyroid hormone (or index) levels. Among depressed patients with elevated FT4I, TSH was higher (p less than .05) on the day of the peak FT4I than on the day of the FT4I nadir. There were significant positive correlations between psychiatric symptom severity and levels of FT4I among both depressed (p less than .01) and schizophrenic (p less than .025) patients. These data show that elevations of T4, FT4I, T3, and FT3I are common among psychiatric inpatients, especially early in their hospitalization, and that levels of thyroid hormones are correlated with severity of psychiatric symptomatology. TSH is higher early in the acute phase of illness and is not suppressed in the face of elevated thyroid hormone levels, a finding that distinguishes this phenomenon from ordinary hyperthyroidism. Elevations of peripheral thyroid hormone levels, particularly among depressed patients, may result from a centrally-mediated hypersecretion of TSH.

Mechanisms of action of (meth)acrylates in hemolytic activity, in vivo toxicity and dipalmitoylphosphatidylcholine (DPPC) liposomes determined using NMR spectroscopy.

PubMed

Fujisawa, Seiichiro; Kadoma, Yoshinori

2012-01-01

We investigated the quantitative structure-activity relationships between hemolytic activity (log 1/H(50)) or in vivo mouse intraperitoneal (ip) LD(50) using reported data for α,β-unsaturated carbonyl compounds such as (meth)acrylate monomers and their (13)C-NMR β-carbon chemical shift (δ). The log 1/H(50) value for methacrylates was linearly correlated with the δC(β) value. That for (meth)acrylates was linearly correlated with log P, an index of lipophilicity. The ipLD(50) for (meth)acrylates was linearly correlated with δC(β) but not with log P. For (meth)acrylates, the δC(β) value, which is dependent on the π-electron density on the β-carbon, was linearly correlated with PM3-based theoretical parameters (chemical hardness, η; electronegativity, χ; electrophilicity, ω), whereas log P was linearly correlated with heat of formation (HF). Also, the interaction between (meth)acrylates and DPPC liposomes in cell membrane molecular models was investigated using (1)H-NMR spectroscopy and differential scanning calorimetry (DSC). The log 1/H(50) value was related to the difference in chemical shift (ΔδHa) (Ha: H (trans) attached to the β-carbon) between the free monomer and the DPPC liposome-bound monomer. Monomer-induced DSC phase transition properties were related to HF for monomers. NMR chemical shifts may represent a valuable parameter for investigating the biological mechanisms of action of (meth)acrylates.

Mechanisms of Action of (Meth)acrylates in Hemolytic Activity, in Vivo Toxicity and Dipalmitoylphosphatidylcholine (DPPC) Liposomes Determined Using NMR Spectroscopy

PubMed Central

Fujisawa, Seiichiro; Kadoma, Yoshinori

2012-01-01

We investigated the quantitative structure-activity relationships between hemolytic activity (log 1/H50) or in vivo mouse intraperitoneal (ip) LD50 using reported data for α,β-unsaturated carbonyl compounds such as (meth)acrylate monomers and their 13C-NMR β-carbon chemical shift (δ). The log 1/H50 value for methacrylates was linearly correlated with the δCβ value. That for (meth)acrylates was linearly correlated with log P, an index of lipophilicity. The ipLD50 for (meth)acrylates was linearly correlated with δCβ but not with log P. For (meth)acrylates, the δCβ value, which is dependent on the π-electron density on the β-carbon, was linearly correlated with PM3-based theoretical parameters (chemical hardness, η; electronegativity, χ; electrophilicity, ω), whereas log P was linearly correlated with heat of formation (HF). Also, the interaction between (meth)acrylates and DPPC liposomes in cell membrane molecular models was investigated using 1H-NMR spectroscopy and differential scanning calorimetry (DSC). The log 1/H50 value was related to the difference in chemical shift (ΔδHa) (Ha: H (trans) attached to the β-carbon) between the free monomer and the DPPC liposome-bound monomer. Monomer-induced DSC phase transition properties were related to HF for monomers. NMR chemical shifts may represent a valuable parameter for investigating the biological mechanisms of action of (meth)acrylates. PMID:22312284

Level II scour analysis for Bridge 28 (ROCHTH00370028) on Town Highway 37, crossing Brandon Brook, Rochester, Vermont

USGS Publications Warehouse

Wild, Emily C.; Weber, Matthew A.

1998-01-01

This report provides the results of a detailed Level II analysis of scour potential at structure ROCHTH00370028 on Town Highway 37 crossing Brandon Brook, Rochester, Vermont (figures 1–8). A Level II study is a basic engineering analysis of the site, including a quantitative analysis of stream stability and scour (FHWA, 1993). Results of a Level I scour investigation also are included in appendix E of this report. A Level I investigation provides a qualitative geomorphic characterization of the study site. Information on the bridge, gleaned from VTAOT files, was compiled prior to conducting Level I and Level II analyses and is found in appendix D. The site is in the Green Mountain section of the New England physiographic province in central Vermont. The 8.0-mi2 drainage area is in a predominantly rural and forested basin. In the vicinity of the study site, the surface cover is pasture on the upstream left overbank although the immediate banks have dense woody vegetation. The upstream right overbank and downstream left and right overbanks are forested. In the study area, the Brandon Brook has an incised, sinuous channel with a slope of approximately 0.01 ft/ft, an average channel top width of 44 ft and an average bank height of 7 ft. The channel bed material ranges from gravel to cobbles with a median grain size (D50) of 84.2 mm (0.276 ft). The geomorphic assessment at the time of the Level I site visit on April 12, 1995 and Level II site visit on July 8, 1996, indicated that the reach was stable. The Town Highway 37 crossing of the Brandon Brook is a 33-ft-long, one-lane bridge consisting of a 31-foot timber-stringer span (Vermont Agency of Transportation, written communication, March 22, 1995). The opening length of the structure parallel to the bridge face is 29.6 ft. The bridge is supported by vertical, timber log cribbing abutments with wingwalls. The channel is skewed approximately 5 degrees to the opening while the computed opening-skew-to-roadway is zero degrees. A scour hole 1.0 ft deeper than the mean thalweg depth was observed along the upstream left wingwall and the left abutment during the Level I assessment. The only scour protection measure at the site was type-5 protection, an artificial levee, extending along the upstream right bank to the end of the upstream right wingwall. Additional details describing conditions at the site are included in the Level II Summary and appendices D and E.Scour depths and recommended rock rip-rap sizes were computed using the general guidelines described in Hydraulic Engineering Circular 18 (Richardson and others, 1995) for the 100- and 500-year discharges. Total scour at a highway crossing is comprised of three components: 1) long-term streambed degradation; 2) contraction scour (due to accelerated flow caused by a reduction in flow area at a bridge) and; 3) local scour (caused by accelerated flow around piers and abutments). Total scour is the sum of the three components. Equations are available to compute depths for contraction and local scour and a summary of the results of these computations follows. Contraction scour for all modelled flows was zero ft. Left abutment scour ranged from 7.1 to 9.9 ft where the worst-case scour occurred at the 500-year discharge. Right abutment scour ranged from 4.4 to 5.1 ft where the worst-case scour occurred at the 500-year discharge. Additional information on scour depths and depths to armoring are included in the section titled “Scour Results.” Scoured-streambed elevations, based on the calculated scour depths, are presented in tables 1 and 2. A cross-section of the scour computed at the bridge is presented in figure 8. Scour depths were calculated assuming an infinite depth of erosive material and a homogeneous particle-size distribution. It is generally accepted that the Froehlich equation (abutment scour) gives “excessively conservative estimates of scour depths” (Richardson and Davis, 1995, p. 46). Usually, computed scour depths are evaluated in combination with other information including (but not limited to) historical performance during flood events, the geomorphic stability assessment, existing scour protection measures, and the results of the hydraulic analyses. Therefore, scour depths adopted by VTAOT may differ from the computed values documented herein

Geophysical Logs, Aquifer Tests, and Water Levels in Wells in and Near the North Penn Area 7 Superfund Site, Upper Gwynedd Township, Montgomery County, Pennsylvania, 2002-2006

USGS Publications Warehouse

Senior, Lisa A.; Conger, Randall W.; Bird, Philip H.

2008-01-01

Ground water in the vicinity of several industrial facilities in Upper Gwynedd Township and Lansdale Borough, Montgomery County, Pa., is contaminated with several volatile organic compounds (VOCs). The 2-square-mile area was placed on the National Priorities List as the North Penn Area 7 Superfund Site by the U.S. Environmental Protection Agency (USEPA) in 1989. The U.S. Geological Survey (USGS) conducted geophysical logging, aquifer testing, water-level monitoring, and streamflow measurements in the vicinity of North Penn Area 7 from October 2002 through December 2006. This followed work that began in 2000 to assist the USEPA in developing an understanding of the hydrogeologic framework in the area as part of the USEPA Remedial Investigation. The study area is underlain by Triassic- and Jurassic-age sandstones, siltstones, and shales of the Lockatong Formation and the Brunswick Group. Regionally, these rocks strike northeast and dip to the northwest. The sequence of rocks form fractured-rock aquifers that act as a set of confined to semi-confined layered aquifers of differing permeabilities. The aquifers are recharged by precipitation and discharge to streams and wells. The Wissahickon Creek headwaters are less than 1 mile northeast of the study area. This stream flows southwest approximately parallel to strike and bisects North Penn Area 7. Ground water is pumped in the vicinity of North Penn Area 7 for industrial use and public supply. The USGS collected geophysical logs for 42 wells that ranged in depth from 40 to 477 ft. Aquifer-interval-isolation testing was done in 17 of the 42 wells, for a total of 122 zones tested. A multiple-well aquifer test was conducted by monitoring the response of 14 wells to pumping and shutdown of a 600-ft deep production well in November-December 2004. In addition, water levels were monitored continuously in four wells in the area from October 2002 through September 2006, and streamflow was measured quarterly at two sites on Wissahickon Creek from December 2002 through September 2005. Geophysical logging identified water-bearing zones associated with high-angle fractures and bedding-plane openings throughout the depth of the boreholes. Heatpulse-flowmeter measurements under non-pumping, ambient conditions in 16 wells greater than 200 ft in depth indicated that borehole flow, where detected, was only upward in 2 wells and only downward in 5 wells. In nine wells, both upward and downward flow were measured. Geologic structure and pumping in the area affect the spatial distribution of vertical gradients. Heatpulse-flowmeter measurements under pumping conditions were used to identify the most productive intervals in wells. Correlation of natural-gamma-ray logs indicated bedding in the area probably strikes about 45 to 65 degrees northeast and dips about 9 degrees northwest. Aquifer intervals isolated by inflatable packers in 17 wells were pumped to test productivity of water-bearing zones and to collect samples to determine chemical quality of water produced from the interval. Interval-isolation testing confirmed the vertical hydraulic gradients indicated by heatpulse-flowmeter measurements. The specific capacities of the 122 isolated intervals ranged over about three orders of magnitude, from 0.01 to 10.6 gallons per minute per foot, corresponding to calculated transmissivities of 1.2 to 2,290 feet squared per day. Intervals adjacent to isolated pumped intervals commonly showed little response to pumping of the isolated zone. The presence of vertical hydraulic gradients and lack of adjacent-interval response to pumping in isolated intervals indicate a limited degree of vertical hydraulic connection between the aquifer sections tested. Differences were apparent in inorganic water quality of water from isolated intervals, including pH, specific conductance, and dissolved oxygen. Concentrations of most VOC contaminants in most wells with predominantly upward vertical gradients were g

How to Keep an Infusion Log: Intravenous Immune Globulin (IVIG)

MedlinePlus

How to keep an INFUSION LOG Intravenous Immune Globulin (IVIG) How to keep an INFUSION LOG The Value of Keeping Records Excellence in health care ... keeping track of your Intravenous Immune Globulin (IVIG) infusions. Each of the manufacturers prepares IVIG in a ...

Endogenous sex hormones and memory performance in middle-aged Greek women with subjective memory complaints.

PubMed

Armeni, Eleni; Apostolakis, Michail; Christidi, Foteini; Rizos, Demetrios; Kaparos, George; Panoulis, Konstantinos; Augoulea, Areti; Alexandrou, Andreas; Karopoulou, Evangelia; Zalonis, Ioannis; Triantafyllou, Nikolaos; Lambrinoudaki, Irene

2018-02-01

The changing hormonal milieu during the menopausal transition may contribute to the development of memory disorders. We aimed to assess the association of sex hormones with memory function in a sample of Greek middle-aged women. This pilot study included 44 women with subjective memory complaints. Memory performance was evaluated using the Hopkins Verbal Learning Test (HVLT), the Brief Visuospatial Memory test (BVMT), and the verbal digits backwards test (VSPAN), to assess verbal, visuospatial, and working memory performance, respectively. Menopausal symptoms were assessed using the Green Climacteric Scale. VSPAN backwards scores were positively associated with log-transformed free androgen index (logFAI), in models adjusted for age, education, log-transformed free estrogen index (logFEI), hypertension, and the intensity of menopausal symptoms. BVMT total scores were predicted by logFAI (b-coefficient = 0.424, p value = 0.002), education, and combined climacteric symptomatology, in a model adjusted for age, logFEI, and hypertension. Women with circulating estradiol above the median value of 10 pg/mL had better total HTLV total scores compared to women with estradiol values below the median (HTLV total scores, estradiol ≤ 10 pg/mL vs. > 10 pg/mL: 24.2 ± 3.6 vs. 30.0 ± 7.9, p value = 0.007 unadjusted). This association was affected by education and remained independent of menopausal symptoms and testosterone levels, education, and hypertension (model R 2 = 22.3%; b-coefficient = 0.318, p value = 0.024). Endogenous total estradiol is associated with verbal episodic memory, while logFAI is associated with working memory performance and visuospatial episodic memory in this sample of postmenopausal women. These associations were not influenced by age, education, or menopausal symptoms. Larger studies are necessary to evaluate the significance of our findings.

Delineation of fractures, foliation, and groundwater of the bedrock at a geothermal feasibility site on Roosevelt Island, New York County, New York

USGS Publications Warehouse

Stumm, Frederick; Chu, Anthony; Como, Michael D.; Noll, Michael L.; Joesten, Peter K.

2015-01-01

Advanced borehole-geophysical methods were used to investigate the hydrogeology of the crystalline bedrock in three boreholes on Roosevelt Island, New York County, New York. Cornell University was evaluating the feasibility of using geothermal energy for a future campus at the site. The borehole-logging techniques were used to delineate bedrock fractures, foliation, and groundwater-flow zones of the Fordham Gneiss in test boreholes at the site. Three fracture populations dominated by small (0.04 in or less) fractures were delineated in the three boreholes. A sub-horizontal population with low to moderate dipping fractures, a northeast dipping population with moderate to high angle fractures, and a small northwest dipping high angle fracture population. One large southwest dipping transmissive fracture underlies the entire study area with a mean dip azimuth of 235º southwest and a dip angle of 31º (N325ºW 31ºSW). The mean foliation dip azimuth was 296º northwest with a mean dip angle of 73º (N26ºE 73ºNW). Groundwater appears to flow through a network of fractures dominated by a large fracture underlying the site that is affected by tidal variations from the nearby East River. The total number of fractures penetrated by each borehole was 95, 63, and 68, with fracture indices of 0.26, 0.20, and 0.20 in GT-1 (NY292), GT-2 (NY293), and GT-3 (NY294), respectively. Aquifer test data indicate the specific capacity of boreholes GT-1 (NY292), GT-2 (NY293), and GT-3 (NY294) was 1.9, 1.5, and 3.7 gal/min/ft, respectively. The large contribution of flow from the leaking casing in borehole GT-3 (NY294) caused the doubling in specific capacity compared to boreholes GT-1 (NY292) and GT-2 (NY293). The transmissivities of the large fracture intersected by the three boreholes tested (GT-1, GT-2, and GT-3), calculated from aquifer-test analyses of time-drawdown data and flowmeter differencing, were 133, 124, and 65 feet squared per day (ft2/d), respectively. Gringarten analysis indicated the large fracture intersects a low transmissivity boundary or distant fracture network with an average transmissivity of 69 ft2/d, this distant hydraulic boundary averages about 200 ft away from boreholes GT-1 and GT-2. Field measurements of specific conductance of the three boreholes under ambient conditions at the site indicate an increase in conductivity toward the southwest part of the site. Specific conductance was 5, 6, and 23 millisiemens per centimeter (mS/cm) in boreholes GT-2, GT-3, and GT-1, respectively. Three borehole radar reflection logs collected at each of the boreholes indicated increased penetration with depth and the large fracture intersecting all three boreholes was imaged as far as 80 ft from the boreholes. A borehole radar attenuation tomogram from GT-1 to GT-2 indicated the large fracture intersected by the boreholes extends between the boreholes with a low angle southwest dip.

Subdivision of the Cambrian-Ordovician Upper Sandstone Aquifer'' in the Fox Cities area, east-central Wisconsin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erikson, K.A.; Smith, G.L.

The informally-named Upper Sandstone Aquifer,'' a lithologically heterogeneous unit, has been subdivided into three thinner hydrostratigraphic units, the Upper Cambrian Jordan Formation (sandstone), the Lower Ordovician Prairie du Chien Group (dolomite), and the Middle Ordovician St. Peter Formation (mostly sandstone). Reevaluation of the Upper Sandstone Aquifer'' in the Fox Cities area (Appleton, Neenah, Menasha) was based on detailed analysis of 125 geologic well logs and 200 well-construction reports. Isopach maps and geologic cross-sections of these units in the Fox Cities area show extreme variations in thickness over short lateral distances. Although the Jordan Formation has a uniform thickness of 13more » m (40 ft), the Prairie du Chien Group varies from 0--88 m (0--275 ft). The St. Peter Formation varies in thickness from 0--108 m (0--335 ft). The Prairie du Chien Group is relatively thin or absent in the Fox Cities area in locations where the overlying St. Peter Formation is relatively thick. St Peter can be further subdivided into Readstown, Tonti, and Glenwood Members. The Readstown Member is a lithologically heterogeneous unit of variable thickness and distribution. The Tonti Member is a poorly cemented, fine-medium quartz arenite with which is lumped the Glenwood Member, a conglomeratic, silty medium-coarse sandstone. Maximum St. Peter thicknesses represent filled paleokarst depressions developed on top of the Prairie du Chien Group, with profound implications for estimates of hydraulic conductivity.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parra, J.; Collier, H.; Angstman, B.

In low porosity, low permeability zones, natural fractures are the primary source of permeability which affect both production and injection of fluids. The open fractures do not contribute much to porosity, but they provide an increased drainage network to any porosity. An important approach to characterizing the fracture orientation and fracture permeability of reservoir formations is one based upon the effects of such conditions on the propagation of acoustic and seismic waves in the rock. We present the feasibility of using seismic measurement techniques to map the fracture zones between wells spaced 2400 ft at depths of about 1000 ft.more » For this purpose we constructed computer models (which include azimuthal anisotropy) using Lodgepole reservoir parameters to predict seismic signatures recorded at the borehole scale, crosswell scale, and 3 D seismic scale. We have integrated well logs with existing 2D surfaces seismic to produce petrophysical and geological cross sections to determine the reservoir parameters and geometry for the computer models. In particular, the model responses are used to evaluate if surface seismic and crosswell seismic measurements can capture the anisotropy due to vertical fractures. Preliminary results suggested that seismic waves transmitted between two wells will propagate in carbonate fracture reservoirs, and the signal can be received above the noise level at the distance of 2400 ft. In addition, the large velocities contrast between the main fracture zone and the underlying unfractured Boundary Ridge Member, suggested that borehole reflection imaging may be appropriate to map and fracture zone thickness variation and fracture distributions in the reservoir.« less

Prognostic value of alcohol dehydrogenase mRNA expression in gastric cancer.

PubMed

Guo, Erna; Wei, Haotang; Liao, Xiwen; Xu, Yang; Li, Shu; Zeng, Xiaoyun

2018-04-01

Previous studies have reported that alcohol dehydrogenase (ADH) isoenzymes possess diagnostic value in gastric cancer (GC). However, the prognostic value of ADH isoenzymes in GC remains unclear. The aim of the present study was to identify the prognostic value of ADH genes in patients with GC. The prognostic value of ADH genes was investigated in patients with GC using the Kaplan-Meier plotter tool. Kaplan-Meier plots were used to assess the difference between groups of patients with GC with different prognoses. Hazard ratios (HR) and 95% confidence intervals (CI) were used to assess the relative risk of GC survival. Overall, 593 patients with GC and 7 ADH genes were included in the survival analysis. High expression of ADH 1A (class 1), α polypeptide ( ADH1A; log-rank P=0.043; HR=0.79; 95% CI: 0.64-0.99), ADH 1B (class 1), β polypeptide ( ADH1B ; log-rank P=1.9×10 -05 ; HR=0.65; 95% CI: 0.53-0.79) and ADH 5 (class III), χ polypeptide ( ADH5 ; log-rank P=0.0011; HR=0.73; 95% CI: 0.6-0.88) resulted in a significantly decreased risk of mortality in all patients with GC compared with patients with low expression of those genes. Furthermore, protective effects may additionally be observed in patients with intestinal-type GC with high expression of ADH1B (log-rank P=0.031; HR=0.64; 95% CI: 0.43-0.96) and patients with diffuse-type GC with high expression of ADH1A (log-rank P=0.014; HR=0.51; 95% CI: 0.3-0.88), ADH1B (log-rank P=0.04; HR=0.53; 95% CI: 0.29-0.98), ADH 4 (class II), π polypeptide (log-rank P=0.033; HR=0.58; 95% CI: 0.35-0.96) and ADH 6 (class V) (log-rank P=0.037; HR=0.59; 95% CI: 0.35-0.97) resulting in a significantly decreased risk of mortality compared with patients with low expression of those genes. In contrast, patients with diffuse-type GC with high expression of ADH5 (log-rank P=0.044; HR=1.66; 95% CI: 1.01-2.74) were significantly correlated with a poor prognosis. The results of the present study suggest that ADH1A and ADH1B may be potential prognostic biomarkers of GC, whereas the prognostic value of other ADH genes requires further investigation.

Prognostic value of alcohol dehydrogenase mRNA expression in gastric cancer

PubMed Central

Guo, Erna; Wei, Haotang; Liao, Xiwen; Xu, Yang; Li, Shu; Zeng, Xiaoyun

2018-01-01

Previous studies have reported that alcohol dehydrogenase (ADH) isoenzymes possess diagnostic value in gastric cancer (GC). However, the prognostic value of ADH isoenzymes in GC remains unclear. The aim of the present study was to identify the prognostic value of ADH genes in patients with GC. The prognostic value of ADH genes was investigated in patients with GC using the Kaplan-Meier plotter tool. Kaplan-Meier plots were used to assess the difference between groups of patients with GC with different prognoses. Hazard ratios (HR) and 95% confidence intervals (CI) were used to assess the relative risk of GC survival. Overall, 593 patients with GC and 7 ADH genes were included in the survival analysis. High expression of ADH 1A (class 1), α polypeptide (ADH1A; log-rank P=0.043; HR=0.79; 95% CI: 0.64–0.99), ADH 1B (class 1), β polypeptide (ADH1B; log-rank P=1.9×10−05; HR=0.65; 95% CI: 0.53–0.79) and ADH 5 (class III), χ polypeptide (ADH5; log-rank P=0.0011; HR=0.73; 95% CI: 0.6–0.88) resulted in a significantly decreased risk of mortality in all patients with GC compared with patients with low expression of those genes. Furthermore, protective effects may additionally be observed in patients with intestinal-type GC with high expression of ADH1B (log-rank P=0.031; HR=0.64; 95% CI: 0.43–0.96) and patients with diffuse-type GC with high expression of ADH1A (log-rank P=0.014; HR=0.51; 95% CI: 0.3–0.88), ADH1B (log-rank P=0.04; HR=0.53; 95% CI: 0.29–0.98), ADH 4 (class II), π polypeptide (log-rank P=0.033; HR=0.58; 95% CI: 0.35–0.96) and ADH 6 (class V) (log-rank P=0.037; HR=0.59; 95% CI: 0.35–0.97) resulting in a significantly decreased risk of mortality compared with patients with low expression of those genes. In contrast, patients with diffuse-type GC with high expression of ADH5 (log-rank P=0.044; HR=1.66; 95% CI: 1.01–2.74) were significantly correlated with a poor prognosis. The results of the present study suggest that ADH1A and ADH1B may be potential prognostic biomarkers of GC, whereas the prognostic value of other ADH genes requires further investigation. PMID:29552190

Accurate computation of survival statistics in genome-wide studies.

PubMed

Vandin, Fabio; Papoutsaki, Alexandra; Raphael, Benjamin J; Upfal, Eli

2015-05-01

A key challenge in genomics is to identify genetic variants that distinguish patients with different survival time following diagnosis or treatment. While the log-rank test is widely used for this purpose, nearly all implementations of the log-rank test rely on an asymptotic approximation that is not appropriate in many genomics applications. This is because: the two populations determined by a genetic variant may have very different sizes; and the evaluation of many possible variants demands highly accurate computation of very small p-values. We demonstrate this problem for cancer genomics data where the standard log-rank test leads to many false positive associations between somatic mutations and survival time. We develop and analyze a novel algorithm, Exact Log-rank Test (ExaLT), that accurately computes the p-value of the log-rank statistic under an exact distribution that is appropriate for any size populations. We demonstrate the advantages of ExaLT on data from published cancer genomics studies, finding significant differences from the reported p-values. We analyze somatic mutations in six cancer types from The Cancer Genome Atlas (TCGA), finding mutations with known association to survival as well as several novel associations. In contrast, standard implementations of the log-rank test report dozens-hundreds of likely false positive associations as more significant than these known associations.

Accurate Computation of Survival Statistics in Genome-Wide Studies

PubMed Central

Vandin, Fabio; Papoutsaki, Alexandra; Raphael, Benjamin J.; Upfal, Eli

2015-01-01

A key challenge in genomics is to identify genetic variants that distinguish patients with different survival time following diagnosis or treatment. While the log-rank test is widely used for this purpose, nearly all implementations of the log-rank test rely on an asymptotic approximation that is not appropriate in many genomics applications. This is because: the two populations determined by a genetic variant may have very different sizes; and the evaluation of many possible variants demands highly accurate computation of very small p-values. We demonstrate this problem for cancer genomics data where the standard log-rank test leads to many false positive associations between somatic mutations and survival time. We develop and analyze a novel algorithm, Exact Log-rank Test (ExaLT), that accurately computes the p-value of the log-rank statistic under an exact distribution that is appropriate for any size populations. We demonstrate the advantages of ExaLT on data from published cancer genomics studies, finding significant differences from the reported p-values. We analyze somatic mutations in six cancer types from The Cancer Genome Atlas (TCGA), finding mutations with known association to survival as well as several novel associations. In contrast, standard implementations of the log-rank test report dozens-hundreds of likely false positive associations as more significant than these known associations. PMID:25950620

Partition of volatile organic compounds from air and from water into plant cuticular matrix: An LFER analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Platts, J.A.; Abraham, M.H.

The partitioning of organic compounds between air and foliage and between water and foliage is of considerable environmental interest. The purpose of this work is to show that partitioning into the cuticular matrix of one particular species can be satisfactorily modeled by general equations the authors have previously developed and, hence, that the same general equations could be used to model partitioning into other plant materials of the same or different species. The general equations are linear free energy relationships that employ descriptors for polarity/polarizability, hydrogen bond acidity and basicity, dispersive effects, and volume. They have been applied to themore » partition of 62 very varied organic compounds between cuticular matrix of the tomato fruit, Lycopersicon esculentum, and either air (MX{sub a}) or water (MX{sub w}). Values of log MX{sub a} covering a range of 12.4 log units are correlated with a standard deviation of 0.232 log unit, and values of log MX{sub w} covering a range of 7.6 log unit are correlated with an SD of 0.236 log unit. Possibilities are discussed for the prediction of new air-plant cuticular matrix and water-plant cuticular matrix partition values on the basis of the equations developed.« less

Pediatric Reference Intervals for Free Thyroxine and Free Triiodothyronine

PubMed Central

Jang, Megan; Guo, Tiedong; Soldin, Steven J.

2009-01-01

Background The clinical value of free thyroxine (FT4) and free triiodothyronine (FT3) analysis depends on the reference intervals with which they are compared. We determined age- and sex-specific reference intervals for neonates, infants, and children 0–18 years of age for FT4 and FT3 using tandem mass spectrometry. Methods Reference intervals were calculated for serum FT4 (n = 1426) and FT3 (n = 1107) obtained from healthy children between January 1, 2008, and June 30, 2008, from Children's National Medical Center and Georgetown University Medical Center Bioanalytical Core Laboratory, Washington, DC. Serum samples were analyzed using isotope dilution liquid chromatography tandem mass spectrometry (LC/MS/MS) with deuterium-labeled internal standards. Results FT4 reference intervals were very similar for males and females of all ages and ranged between 1.3 and 2.4 ng/dL for children 1 to 18 years old. FT4 reference intervals for 1- to 12-month-old infants were 1.3–2.8 ng/dL. These 2.5 to 97.5 percentile intervals were much tighter than reference intervals obtained using immunoassay platforms 0.48–2.78 ng/dL for males and 0.85–2.09 ng/dL for females. Similarly, FT3 intervals were consistent and similar for males and females and for all ages, ranging between 1.5 pg/mL and approximately 6.0 pg/mL for children 1 month of age to 18 years old. Conclusions This is the first study to provide pediatric reference intervals of FT4 and FT3 for children from birth to 18 years of age using LC/MS/MS. Analysis using LC/MS/MS provides more specific quantification of thyroid hormones. A comparison of the ultrafiltration tandem mass spectrometric method with equilibrium dialysis showed very good correlation. PMID:19583487

Rapid monitoring of the fermentation process for Korean traditional rice wine 'Makgeolli' using FT-NIR spectroscopy

NASA Astrophysics Data System (ADS)

Kim, Dae-Yong; Cho, Byoung-Kwan

2015-11-01

The quality parameters of the Korean traditional rice wine "Makgeolli" were monitored using Fourier transform near-infrared (FT-NIR) spectroscopy with multivariate statistical analysis (MSA) during fermentation. Alcohol, reducing sugar, and titratable acid were the parameters assessed to determine the quality index of fermentation substrates and products. The acquired spectra were analyzed with partial least squares regression (PLSR). The best prediction model for alcohol was obtained with maximum normalization, showing a coefficient of determination (Rp2) of 0.973 and a standard error of prediction (SEP) of 0.760%. In addition, the best prediction model for reducing sugar was obtained with no data preprocessing, with a Rp2 value of 0.945 and a SEP of 1.233%. The prediction of titratable acidity was best with mean normalization, showing a Rp2 value of 0.882 and a SEP of 0.045%. These results demonstrate that FT-NIR spectroscopy can be used for rapid measurements of quality parameters during Makgeolli fermentation.

Characterization of 1,5-dimethoxynaphthalene by vibrational spectroscopy (FT-IR and FT-Raman) and density functional theory calculations.

PubMed

Kandasamy, M; Velraj, G; Kalaichelvan, S; Mariappan, G

2015-01-05

In this work, we reported a combined experimental and theoretical study on molecular structure, vibrational spectra and natural bond orbital (NBO) analysis of 1,5-dimethoxynaphthalene. The optimized molecular structure, atomic charges, vibrational frequencies and natural bond orbital analysis of 1,5-dimethoxynaphthalene have been studied by performing DFT/B3LYP/6-31G(d,p) level of theory. The FTIR, FT-Raman spectra were recorded in the region of 4000-400 cm(-1) and 3500-50 cm(-1) respectively. The scaled wavenumbers are compared with the experimental values. The difference between the observed and scaled wavenumber values of the most fundamentals is very small. The formation of hydrogen bond was investigated in terms of the charge density by the NBO analysis. Natural Population Analysis (NPA) was used for charge determination in the title molecule. Besides, molecular electrostatic potential (MEP), frontier molecular orbitals (FMO) analysis were investigated using theoretical calculations. Copyright © 2014 Elsevier B.V. All rights reserved.

Estimating tree grades for Southern Appalachian natural forest stands

Treesearch

Jeffrey P. Prestemon

1998-01-01

Log prices can vary significantly by grade: grade 1 logs are often several times the price per unit of grade 3 logs. Because tree grading rules derive from log grading rules, a model that predicts tree grades based on tree and stand-level variables might be useful for predicting stand values. The model could then assist in the modeling of timber supply and in economic...

SU-F-T-233: Evaluation of Treatment Delivery Parameters Using High Resolution ELEKTA Log Files

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kabat, C; Defoor, D; Alexandrian, A

2016-06-15

Purpose: As modern linacs have become more technologically advanced with the implementation of IGRT and IMRT with HDMLCs, a requirement for more elaborate tracking techniques to monitor components’ integrity is paramount. ElektaLog files are generated every 40 milliseconds, which can be analyzed to track subtle changes and provide another aspect of quality assurance. This allows for constant monitoring of fraction consistency in addition to machine reliability. With this in mind, it was the aim of the study to evaluate if ElektaLog files can be utilized for linac consistency QA. Methods: ElektaLogs were reviewed for 16 IMRT patient plans with >16more » fractions. Logs were analyzed by creating fluence maps from recorded values of MLC locations, jaw locations, and dose per unit time. Fluence maps were then utilized to calculate a 2D gamma index with a 2%–2mm criteria for each fraction. ElektaLogs were also used to analyze positional errors for MLC leaves and jaws, which were used to compute an overall error for the MLC banks, Y-jaws, and X-jaws by taking the root-meansquare value of the individual recorded errors during treatment. Additionally, beam on time was calculated using the number of ElektaLog file entries within the file. Results: The average 2D gamma for all 16 patient plans was found to be 98.0±2.0%. Recorded gamma index values showed an acceptable correlation between fractions. Average RMS values for MLC leaves and the jaws resulted in a leaf variation of roughly 0.3±0.08 mm and jaw variation of about 0.15±0.04 mm, both of which fall within clinical tolerances. Conclusion: The use of ElektaLog files for day-to-day evaluation of linac integrity and patient QA can be utilized to allow for reliable analysis of system accuracy and performance.« less

SU-E-T-184: Clinical VMAT QA Practice Using LINAC Delivery Log Files

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, H; Jacobson, T; Gu, X

2015-06-15

Purpose: To evaluate the accuracy of volumetric modulated arc therapy (VMAT) treatment delivery dose clouds by comparing linac log data to doses measured using an ionization chamber and film. Methods: A commercial IMRT quality assurance (QA) process utilizing a DICOM-RT framework was tested for clinical practice using 30 prostate and 30 head and neck VMAT plans. Delivered 3D VMAT dose distributions were independently checked using a PinPoint ionization chamber and radiographic film in a solid water phantom. DICOM RT coordinates were used to extract the corresponding point and planar doses from 3D log file dose distributions. Point doses were evaluatedmore » by computing the percent error between log file and chamber measured values. A planar dose evaluation was performed for each plan using a 2D gamma analysis with 3% global dose difference and 3 mm isodose point distance criteria. The same analysis was performed to compare treatment planning system (TPS) doses to measured values to establish a baseline assessment of agreement. Results: The mean percent error between log file and ionization chamber dose was 1.0%±2.1% for prostate VMAT plans and −0.2%±1.4% for head and neck plans. The corresponding TPS calculated and measured ionization chamber values agree within 1.7%±1.6%. The average 2D gamma passing rates for the log file comparison to film are 98.8%±1.0% and 96.2%±4.2% for the prostate and head and neck plans, respectively. The corresponding passing rates for the TPS comparison to film are 99.4%±0.5% and 93.9%±5.1%. Overall, the point dose and film data indicate that log file determined doses are in excellent agreement with measured values. Conclusion: Clinical VMAT QA practice using LINAC treatment log files is a fast and reliable method for patient-specific plan evaluation.« less

Level II scour analysis for Bridge 41 (WODSTH00750041) on Town Highway 75, crossing Happy Valley Brook, Woodstock, Vermont

USGS Publications Warehouse

Olson, Scott A.

1996-01-01

This report provides the results of a detailed Level II analysis of scour potential at structure WODSTH00750041 on town highway 75 crossing Happy Valley Brook, Woodstock, Vermont (figures 1–8). A Level II study is a basic engineering analysis of the site, including a quantitative analysis of stream stability and scour (U.S. Department of Transportation, 1993). Results of a Level I scour investigation also are included in Appendix E of this report. A Level I investigation provides a qualitative geomorphic characterization of the study site. Information on the bridge, gleaned from Vermont Agency of Transportation (VTAOT) files, was compiled prior to conducting Level I and Level II analyses and is found in Appendix D. The site is in the New England Upland section of the New England physiographic province of east-central Vermont. The 3.45-mi2 drainage area is in a predominantly rural and forested basin. In the vicinity of the study site, the surface cover is brush with scattered trees. In the study area, Happy Valley Brook has an incised, sinuous channel with a slope of approximately 0.03 ft/ft, an average channel top width of 23 ft and an average channel depth of 5 ft. The predominant channel bed materials are gravel and cobble with a median grain size (D50) of 82.8 mm (0.272 ft). The geomorphic assessment at the time of the Level II site visits on September 13, 1994 and December 14, 1994, indicated that the reach was degrading. Five logs are embedded across the channel under the bridge in an attempt to prevent further degradation (see Figures 5 and 6). The town highway 75 crossing of Happy Valley Brook is a 27-ft-long, two-lane bridge consisting of one 25-foot steel-beam span. The clear span is 17 ft. (Vermont Agency of Transportation, written communication, August 3, 1994). The bridge is supported by vertical, stone abutments with wingwalls. The channel is skewed approximately 40 degrees to the opening and the opening-skew-to-roadway is also 40 degrees. Additional details describing conditions at the site are included in the Level II Summary and Appendices D and E. Scour depths and rock rip-rap sizes were computed using the general guidelines described in Hydraulic Engineering Circular 18 (Richardson and others, 1995). Total scour at a highway crossing is comprised of three components: 1) long-term streambed degradation; 2) contraction scour (due to accelerated flow caused by a reduction in flow area at a bridge) and; 3) local scour (caused by accelerated flow around piers and abutments). Total scour is the sum of the three components. Equations are available to compute depths for contraction and local scour and a summary of the results of these computations follows. Contraction scour for all modelled flows ranged from 1.3 to 2.2 ft. The worst-case contraction scour occurred at the 500-year discharge. Abutment scour ranged from 7.2 to 12.0 ft. The worst-case abutment scour occurred at the 500-year discharge. Additional information on scour depths and depths to armoring are included in the section titled “Scour Results”. Scoured-streambed elevations, based on the calculated scour depths, are presented in tables 1 and 2. A cross-section of the scour computed at the bridge is presented in figure 8. Scour depths were calculated assuming an infinite depth of erosive material and a homogeneous particle-size distribution. It is generally accepted that the Froehlich equation (abutment scour) gives “excessively conservative estimates of scour depths” (Richardson and others, 1995, p. 47). Usually, computed scour depths are evaluated in combination with other information including (but not limited to) historical performance during flood events, the geomorphic stability assessment, existing scour protection measures, and the results of the hydraulic analyses. Therefore, scour depths adopted by VTAOT may differ from the computed values documented herein.

Stand Parameters of a 27-Year-Old Water Oak Plantation on Old Field Loessial Soils

Treesearch

Roger M. Krinard; Robert L. Johnson

1988-01-01

At age 27, water oak (Quercus nigra L.) plantings on Macon Ridge old field loessial soil near Winnsboro, Louisiana, had per-acre stand values as follows: number of trees, 356; average d.b.h., 6.6 inches; basal area, 86 ft2; total volume from the stump to the tip (of trees with d.b.h. 25.0 in), 2,017 ft3...

Automated Carrier Landing of an Unmanned Combat Aerial Vehicle Using Dynamic Inversion

DTIC Science & Technology

2007-06-01

17 CN normal force coefficient . . . . . . . . . . . . . . . . . . . . 17 CA axial force coefficient...slug·ft2 Ixzb 0 slug·ft2 The aircraft has a single engine inlet for a single, centerline mounted turbofan engine. For purposes of this research, the...assumed to remain constant for each simulation run and were based on an assumed 10% fuel load with full weapons [2]. The rest of these values were

Spectroscopic (FT-IR, FT-Raman, and UV-visible) and quantum chemical studies on molecular geometry, Frontier molecular orbitals, NBO, NLO and thermodynamic properties of 1-acetylindole.

PubMed

Shukla, Vikas K; Al-Abdullah, Ebtehal S; El-Emam, Ali A; Sachan, Alok K; Pathak, Shilendra K; Kumar, Amarendra; Prasad, Onkar; Bishnoi, Abha; Sinha, Leena

2014-12-10

Quantum chemical calculations of ground state energy, geometrical structure and vibrational wavenumbers of 1-acetylindole were carried out using density functional (DFT/B3LYP) method with 6-311++G(d,p) basis set. The FT-IR and FT-Raman spectra were recorded in the condensed state. The fundamental vibrational wavenumbers were calculated and a good correlation between experimental and scaled calculated wavenumbers has been accomplished. Electric dipole moment, polarizability and first static hyperpolarizability values of 1-acetylindole have been calculated at the same level of theory and basis set. The results show that the 1-acetylindole molecule possesses nonlinear optical (NLO) behavior with non-zero values. Stability of the molecule arising from hyper-conjugative interactions and charge delocalization has been analyzed using natural bond orbital (NBO) analysis. UV-Visible spectrum of the molecule was recorded in the region 200-500nm and the electronic properties like HOMO and LUMO energies and composition were obtained using TD-DFT method. The calculated energies and oscillator strengths are in good correspondence with the experimental data. The thermodynamic properties of the compound under investigation were calculated at different temperatures. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of Atomic Charges on Octanol-Water Partition Coefficient Using Alchemical Free Energy Calculation.

PubMed

Ogata, Koji; Hatakeyama, Makoto; Nakamura, Shinichiro

2018-02-15

The octanol-water partition coefficient (log P ow ) is an important index for measuring solubility, membrane permeability, and bioavailability in the drug discovery field. In this paper, the log P ow values of 58 compounds were predicted by alchemical free energy calculation using molecular dynamics simulation. In free energy calculations, the atomic charges of the compounds are always fixed. However, they must be recalculated for each solvent. Therefore, three different sets of atomic charges were tested using quantum chemical calculations, taking into account vacuum, octanol, and water environments. The calculated atomic charges in the different environments do not necessarily influence the correlation between calculated and experimentally measured ∆ G water values. The largest correlation coefficient values of the solvation free energy in water and octanol were 0.93 and 0.90, respectively. On the other hand, the correlation coefficient of log P ow values calculated from free energies, the largest of which was 0.92, was sensitive to the combination of the solvation free energies calculated from the calculated atomic charges. These results reveal that the solvent assumed in the atomic charge calculation is an important factor determining the accuracy of predicted log P ow values.

Veneer recovery from peeler-grade Douglas-fir logs in northwestern Oregon.

Treesearch

E.H. Clarke; A.C. Knauss

1957-01-01

Continued expansion of Douglas-fir plywood production develops a greater demand for all grades of peelable logs to supply the industry. Thus, it becomes increasingly important to know the veneer-grade recovery expected so that timber and log values can be more accurately appraised.

Improving log transportation with data based monitoring and analysis in northern Wisconsin and upper peninsula of Michigan.

DOT National Transportation Integrated Search

2012-02-01

Minimizing transportation cost is essential in the forest products industry. Logs and wood chips are relatively low value. Logs are a dense heavy weight product to transport, while chips are light and bulky. These handling characteristics along with ...

Parallel checksumming of data chunks of a shared data object using a log-structured file system

DOEpatents

Bent, John M.; Faibish, Sorin; Grider, Gary

2016-09-06

Checksum values are generated and used to verify the data integrity. A client executing in a parallel computing system stores a data chunk to a shared data object on a storage node in the parallel computing system. The client determines a checksum value for the data chunk; and provides the checksum value with the data chunk to the storage node that stores the shared object. The data chunk can be stored on the storage node with the corresponding checksum value as part of the shared object. The storage node may be part of a Parallel Log-Structured File System (PLFS), and the client may comprise, for example, a Log-Structured File System client on a compute node or burst buffer. The checksum value can be evaluated when the data chunk is read from the storage node to verify the integrity of the data that is read.

Prediction of kinase-inhibitor binding affinity using energetic parameters

PubMed Central

Usha, Singaravelu; Selvaraj, Samuel

2016-01-01

The combination of physicochemical properties and energetic parameters derived from protein-ligand complexes play a vital role in determining the biological activity of a molecule. In the present work, protein-ligand interaction energy along with logP values was used to predict the experimental log (IC50) values of 25 different kinase-inhibitors using multiple regressions which gave a correlation coefficient of 0.93. The regression equation obtained was tested on 93 kinase-inhibitor complexes and an average deviation of 0.92 from the experimental log IC50 values was shown. The same set of descriptors was used to predict binding affinities for a test set of five individual kinase families, with correlation values > 0.9. We show that the protein-ligand interaction energies and partition coefficient values form the major deterministic factors for binding affinity of the ligand for its receptor. PMID:28149052

Free Triiodothyronine Concentrations are Inversely Associated with Elevated Carotid Intima-Media Thickness in Middle-Aged and Elderly Chinese Population.

PubMed

Zhou, Yulin; Zhao, Liebin; Wang, Tiange; Hong, Jie; Zhang, Jie; Xu, Baihui; Huang, Xiaolin; Xu, Min; Bi, Yufang

2016-01-01

Increased carotid artery intima media thickness (C-IMT) is an early feature of atherosclerosis. It has been reported to be altered in patients with thyroid dysfunction, and the evidence is still controversial. The present study aimed to explore the relationship between C-IMT and possible variations in thyroid function in Chinese adults aged 40 years and above. A community-based cross-sectional study was conducted among 2276 non-diabetic participants. Serum free triiodothyronine (FT3), free thyroxine (FT4), and thyroid stimulating hormone (TSH) were determined by chemiluminescent microparticle immunoassay. The prevalence of elevated C-IMT decreased according to FT3 quartiles (29.8%, 24.3%, 24.2%, and 22.2%, P for trend=0.005). In both univariate and multivariate linear regression analyses, FT3 levels were inversely associated with C-IMT (both P values ≤ 0.002). Multivariate-adjusted logistic regression analysis showed that high FT3 levels were associated with low prevalent elevated C-IMT. The adjusted odds ratio for elevated C-IMT was 0.71 (95% confidence interval, 0.52-0.99, P=0.04) when comparing the highest with the lowest quartile of FT3. Serum FT3 levels were inversely associated with elevated C-IMT in middle-aged and elderly Chinese adults without diabetes, independent of traditional risk factors for atherosclerosis.

A scale of metal ion binding strengths correlating with ionic charge, Pauling electronegativity, toxicity, and other physiological effects.

PubMed

Kinraide, Thomas B; Yermiyahu, Uri

2007-09-01

Equilibrium constants for binding to plant plasma membranes have been reported for several metal ions, based upon adsorption studies and zeta-potential measurements. LogK values for the ions are these: Al(3+), 4.30; La(3+), 3.34; Cu(2+), 2.60; Ca(2+) and Mg(2+), 1.48; Na(+) and K(+), 0 M(-1). These values correlate well with logK values for ion binding to many organic and inorganic ligands. LogK values for metal ion binding to 12 ligands were normalized and averaged to produce a scale for the binding of 49 ions. The scale correlates well with the values presented above (R(2)=0.998) and with ion binding to cell walls and other biomass. The scale is closely related to the charge (Z) and Pauling electronegativity (PE) of 48 ions (all but Hg(2+)); R(2)=0.969 for the equation (Scale values)=-1.68+Z(1.22+0.444PE). Minimum rhizotoxicity of metal ions appears to be determined by binding strengths: log a(PM,M)=1.60-2.41exp[0.238(Scale values)] determines the value of ion activities at the plasma membrane surface (a(PM,M)) that will ensure inhibition of root elongation. Additional toxicity appears to be related to softness, accounting for the great toxicity of Ag(+), for example. These binding-strength values correlate with additional physiological effects and are suitable for the computation of cell-surface electrical potentials.

Comparisons of four computer models with experimental data from test buildings in northern New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Robertson, D.K.; Christian, J.E.

1985-01-01

Eight one-room test buildings, 20 ft (6.1 m) square and 7.5 ft (2.3 m) high, were constructed on a high desert site near Tesuque Pueblo, New Mexico, to study the influence of wall dynamic heat transfer characteristics on building heating requirements (the ''thermal mass effect''). The buildings are nominally identical except for the walls (adobe, concrete and masonry unit, wood-frame, and log) and are constructed so as to isolate the effects of the walls. The amount of mass in the walls varies from 240 lb/ft/sup 2/ (1171 kg/m/sup 2/) for the 2 ft (.61 m) thick adobe wall to 4.3more » lb/ft/sup 2/ (21 kg/m/sup 2/) for the insulated wood-frame wall. The roof, floor, and stem walls are all well insulated and the buildings were constructed with infiltration rates less than 0.4 air change per hour. The site is instrumented to record building component temperatures and heat fluxes, outside weather conditions, and heating energy use. Data were collected for two heating seasons from midwinter to late spring with the buildings in two configurations, with and without windows. Four computer codes were used to simulate the performance of the test buildings without windows, using site weather data. The codes used were DOE-2.1A, DOE-2.1C, BLAST, and DEROB. Each code was run by a different analyst. Simulations were done for midwinter, late winter, and spring. Two of the test cell comparisons are discussed; the insulated frame and an 11-in. (.28 m) adobe. This work presents a quantitative and qualitative critical comparison of the modeling and experimental results. Cumulative heating loads, wall heat fluxes, and air surface temperatures are compared, as well as input assumptions to the models. Explanations of differences and difficulties encountered are reported. The principal findings were that cumulative heating loads and the characteristic influences of wall thermal mass on hourly behavior were reproduced by the models.« less

Delineation of fractures, foliation, and groundwater-flow zones of the bedrock at the Harlem River Tunnel in northern New York County, New York

USGS Publications Warehouse

Stumm, Frederick; Chu, Anthony; Joesten, Peter K.; Noll, Michael L.; Como, Michael D.

2013-01-01

Advanced borehole-geophysical methods were used to investigate the hydrogeology of the crystalline bedrock in 36 boreholes on the northernmost part of New York County, New York, for the construction of a utilities tunnel beneath the Harlem River. The borehole-logging techniques were used to delineate bedrock fractures, foliation, and groundwater-flow zones in test boreholes at the site. Fracture indexes of the deep boreholes ranged from 0.65 to 0.76 per foot. Most of the fracture populations had either northwest to southwest or east to southeast dip azimuths with moderate dip angles. The mean foliation dip azimuth ranged from 100º to 124º southeast with dip angles of 52º to 60º. Groundwater appears to flow through an interconnected network of fractures that are affected by tidal variations from the nearby Harlem River and tunnel construction dewatering operations. The transmissivities of the 3 boreholes tested (USGS-1, USGS-3, and USGS-4), calculated from specific capacity data, were 2, 48, and 30 feet squared per day (ft2/d), respectively. The highest transmissivities were observed in wells north and west of the secant ring. Three borehole-radar velocity tomograms were collected. In the USGS-1 and USGS-4 velocity tomogram there are two areas of low radar velocity. The first is at the top of the tomogram and runs from 105 ft below land surface (BLS) at USGS-4 and extends to 125 ft BLS at USGS-1, the second area is centered at a depth of 150 ft BLS at USGS-1 and 135 to 150 ft BLS at USGS-4. Field measurements of specific conductance of 14 boreholes under ambient conditions at the site indicate an increase in conductivity toward the southwest part of the site (nearest the Harlem River). Specific conductance ranged from 107 microsiemens per centimeter (μS/cm) (borehole 63C) to 11,000 μS/cm (borehole 79B). The secant boreholes had the highest specific conductance.

Quantitative Generalizations for Catchment Sediment Yield Following Plantation Logging

NASA Astrophysics Data System (ADS)

Bathurst, James; Iroume, Andres

2014-05-01

While there is a reasonably clear qualitative understanding of the impact of forest plantations on sediment yield, there is a lack of quantitative generalizations. Such generalizations would be helpful for estimating the impacts of proposed forestry operations and would aid the spread of knowledge amongst both relevant professionals and new students. This study therefore analyzed data from the literature to determine the extent to which quantitative statements can be established. The research was restricted to the impact of plantation logging on catchment sediment yield as a function of ground disturbance in the years immediately following logging, in temperate countries, and does not consider landslides consequent upon tree root decay. Twelve paired catchment studies incorporating pre- and post-logging measurements of sediment yield were identified, resulting in forty-three test catchments (including 14 control catchments). Analysis yielded the following principal conclusions: 1) Logging generally provokes maximum annual sediment yields of less than a few hundred t km-2 yr-1; best management practice can reduce this below 100 t km-2 yr-1. 2) At both the annual and event scales, the sediment yield excess of a logged catchment over a control catchment is within one order of magnitude, except with severe ground disturbance. 3) There is no apparent relationship between sediment yield impact and the proportion of catchment logged. The effect depends on which part of the catchment is altered and on its connectivity to the stream network. 4) The majority of catchments delivered their maximum sediment yield in the first two years after logging. The logging impacts were classified in terms of the absolute values of specific sediment yield, the values relative to those in the control catchments for the same period and the values relative both to the control catchment and the pre-logging period. Most studies have been for small catchments (< 10 km2) and temperate regions; the impact at large catchment scales and in tropical regions requires further research.

FTIR, FT-RAMAN, NMR, spectra, normal co-ordinate analysis, NBO, NLO and DFT calculation of N,N-diethyl-4-methylpiperazine-1-carboxamide molecule

NASA Astrophysics Data System (ADS)

Muthu, S.; Elamurugu Porchelvi, E.

2013-11-01

The Fourier Transform Infrared (FT-IR) and FT-Raman of N,N-diethyl-4-methylpiperazine-1-carboxamide (NND4MC) have been recorded and analyzed. The structure of the compound was optimized and the structural characteristics were determined by density functional theory (DFT) using B3LYP method with 6-31G(d,p) and 6-311G(d,p) basis sets. The difference between the observed and scaled wavenumber values of most of the fundamentals is very small. The theoretically predicted FT-IR and FT-Raman spectra of the title molecule have been constructed. The detailed interpretation of the vibrational spectra has been carried out with aid of normal coordinate analysis (NCA) following the scaled quantum mechanical force field methodology. Stability of the molecule arising from hyperconjugative interactions and charge delocalization has been analyzed using natural bond orbital (NBO) analysis. The results show that electron density (ED) in the σ* and π* antibonding orbitals and second order delocalization energies (E2) confirm the occurrence of intramolecular charge transfer (ICT) within the molecule. The electronic dipole moment (μD) and the first hyperpolarizability (βtot) values of the investigated molecule were computed using Density Functional Theory (DFT/B3LYP) with 6-31G(d,p) and 6-311G(d,p) basis sets. The calculated results also show that the NND4MC molecule may have microscopy nonlinear optical (NLO) behavior with non zero values. Mulliken atomic charges of NND4MC were calculated. The 13C nuclear magnetic resonance (NMR) chemical shifts of the molecule were calculated by the gauge independent atomic orbital (GIAO) method and compared with experimental results. The UV-Vis spectrum of the compound was recorded. The theoretical electronic absorption spectra have been calculated by using CIS, TD-DFT methods. A study on the electronic properties, such as HOMO and LUMO energies, molecular electrostatic potential (MEP) were also performed.

Levels at gaging stations

USGS Publications Warehouse

Kenney, Terry A.

2010-01-01

Operational procedures at U.S. Geological Survey gaging stations include periodic leveling checks to ensure that gages are accurately set to the established gage datum. Differential leveling techniques are used to determine elevations for reference marks, reference points, all gages, and the water surface. The techniques presented in this manual provide guidance on instruments and methods that ensure gaging-station levels are run to both a high precision and accuracy. Levels are run at gaging stations whenever differences in gage readings are unresolved, stations may have been damaged, or according to a pre-determined frequency. Engineer's levels, both optical levels and electronic digital levels, are commonly used for gaging-station levels. Collimation tests should be run at least once a week for any week that levels are run, and the absolute value of the collimation error cannot exceed 0.003 foot/100 feet (ft). An acceptable set of gaging-station levels consists of a minimum of two foresights, each from a different instrument height, taken on at least two independent reference marks, all reference points, all gages, and the water surface. The initial instrument height is determined from another independent reference mark, known as the origin, or base reference mark. The absolute value of the closure error of a leveling circuit must be less than or equal to ft, where n is the total number of instrument setups, and may not exceed |0.015| ft regardless of the number of instrument setups. Closure error for a leveling circuit is distributed by instrument setup and adjusted elevations are determined. Side shots in a level circuit are assessed by examining the differences between the adjusted first and second elevations for each objective point in the circuit. The absolute value of these differences must be less than or equal to 0.005 ft. Final elevations for objective points are determined by averaging the valid adjusted first and second elevations. If final elevations indicate that the reference gage is off by |0.015| ft or more, it must be reset.

Transient hyperthyroidism after surgery for secondary hyperparathyroidism: a common problem

PubMed Central

2011-01-01

Background Postoperative hyperthyroidism occurs in approximately one third of patients following parathyroidectomy due to primary hyperparathyroidism (PHP), but has only rarely been described in secondary hyperparathyroidism (SHP). The frequency, course, and laboratory markers of postoperative hyperthyroidism in SHP remain unknown. Our purpose was to evaluate the frequency and the clinical course of postoperative hypcrthyroidism following surgery of SHP and to determine the diagnostic value of thyroglobulin in this setting. Material and Methods A total of 40 patients undergoing parathyroidectomy because of SHP were included in this study. Thyroid stimulating hormone (TSH), free triiodothyronine (fT3), free thyroxine (fl4), and thyroglobulin (Tg) were determined one day before and on day 1, 3, 5, 10, and 40 after surgery. At each of these visits patients were clinically evaluated for signs or symptoms of hyperthyroidism. Results Biochemical evidence of hyperthyroidism was evident in 77% of patients postoperatively despite of preoperatively normal serum levels. TSH dropped from 1.18 ± 0.06mU/L to 0.15 ± 0.07mU/L (p = 0.0015). Free triiodothyronine (fT3) and fT4 levels increased from 2.86 ± 0.02ng/L and 10.32 ± 0.13ng/L, respectively, to their maximum of 4.83 ± 0.17ng/L and 19.35 ± 0.58ng/L, respectively. Thyroglobulin levels rose from 3.8 ± 0.8ng/mL to 111.8 ± 45.3ng/mL (p < 0.001). At day 40 all thyroid related laboratory values were within normal range. Correlation analysis of postoperative values revealed significant correlations for lowest TSH (r = -0.32; p = 0.038), and highest fT3 (r = 0.55; p < 0.001) and fT4 levels (r = 0.67; p < 0.001) with Tg. Conclusion Transient hyperthyroidism is frequent after parathyroidectomy for SHP with Tg being a suitable marker. Awareness of this self-limiting disorder is important to avoid inappropriate and potentially harmful treatment. PMID:21813380

Aquifer test to determine hydraulic properties of the Elm aquifer near Aberdeen, South Dakota

USGS Publications Warehouse

Schaap, Bryan D.

2000-01-01

The Elm aquifer, which consists of sandy and gravelly glacial-outwash deposits, is present in several counties in northeastern South Dakota. An aquifer test was conducted northeast of Aberdeen during the fall of 1999 to determine the hydraulic properties of the Elm aquifer in that area. An improved understanding of the properties of the aquifer will be useful in the possible development of the aquifer as a water resource. Historical water-level data indicate that the saturated thickness of the Elm aquifer can change considerably over time. From September 1977 through November 1985, water levels at three wells completed in the Elm aquifer near the aquifer test site varied by 5.1 ft, 9.50 ft, and 11.1 ft. From June 1982 through October 1999, water levels at five wells completed in the Elm aquifer near the aquifer test site varied by 8.7 ft, 11.4 ft, 13.2 ft, 13.8 ft, and 19.7 ft. The water levels during the fall of 1999 were among the highest on record, so the aquifer test was affected by portions of the aquifer being saturated that might not be saturated during drier times. The aquifer test was conducted using five existing wells that had been installed prior to this study. Well A, the pumped well, has an operating irrigation pump and is centrally located among the wells. Wells B, C, D, and E are about 70 ft, 1,390 ft, 2,200 ft, and 3,100 ft, respectively, in different directions from Well A. Using vented pressure transducers and programmable data loggers, water-level data were collected at the five wells prior to, during, and after the pumping, which started on November 19, 1999, and continued a little over 72 hours. Based on available drilling logs, the Elm aquifer near the test area was assumed to be unconfined. The Neuman (1974) method theoretical response curves that most closely match the observed water-level changes at Wells A and B were calculated using software (AQTESOLV for Windows Version 2.13-Professional) developed by Glenn M. Duffield of HydroSOLVE, Inc. These best fit theoretical response curves are based on a transmissivity of 24,000 ft2/d or a hydraulic conductivity of about 600 ft/d, a storage coefficient of 0.05, a specific yield of 0.42, and vertical hydraulic conductivity equal to horizontal hydraulic conductivity. The theoretical type curves match the observed data fairly closely at Wells A and B until about 2,500 minutes and 1,000 minutes, respectively, after pumping began. The increasing rate of drawdown after these breaks is an indication that a no-flow boundary (an area with much lower hydraulic conductivity) likely was encountered and that Wells A and B may be completed in a part of the Elm aquifer with limited hydraulic connection to the rest of the aquifer. Additional analysis indicates that if different assumptions regarding the screened interval for Well B and aquifer anisotropy are used, type curves can be calculated that fit the observed data using a lower specific yield that is within the commonly accepted range. When the screened interval for Well B was reduced to 5 ft near the top of the aquifer and horizontal hydraulic conductivity was set to 20 times vertical hydraulic conductivity, the type curves calculated using a specific yield of 0.1 and a transmissivity of 30,200 ft2/d also matched the observed data from Wells A and B fairly well. A version of the Theim equilibrium equation was used to calculate the theoretical drawdown in an idealized unconfined aquifer when a perfectly efficient well is being pumped at a constant rate. These calculations were performed for a range of pumping rates, drawdowns at the wells, and distances between wells that might be found in a production well field in the Elm aquifer. Although the aquifer test indicates that hydraulic conductivity near the well may be adequate to support a production well, the comparison of drawdown and recovery curves indicates the possibility that heterogeneities may limit the productive capacity of specific loca

Deriving Criteria-supporting Benchmark Values from Empirical Response Relationships: Comparison of Statistical Techniques and Effect of Log-transforming the Nutrient Variable

EPA Science Inventory

In analyses supporting the development of numeric nutrient criteria, multiple statistical techniques can be used to extract critical values from stressor response relationships. However there is little guidance for choosing among techniques, and the extent to which log-transfor...

Acoustic evaluation of loblolly pine tree- and lumber-length logs allows for segregation of lumber modulus of elasticity, not for modulus of rupture

Treesearch

Mark Alexander Butler; Joseph Dahlen; Thomas L. Eberhardt; Cristian Montes; Finto Antony; Richard F. Daniels

2017-01-01

Key message Loblolly pine (Pinus taeda) logs can be evaluated using acoustic velocity whereby threshold acoustic velocity values can be set to ensure lumber meets specified mechanical property design values for modulus of elasticity. Context...

Volume, value, and thinning: logs for the future.

Treesearch

Sally Duncan

2002-01-01

Thinning is one of our most important ways to influence tree and stand development. The objectives may include increasing the volume, size, and quality of wood produced from a forest and developing particular stand structures and characteristics for other values, such as wildlife or aesthetics.The Levels-of-Growing-Stock (LOGS) Cooperative was initiated in...

Forest products harvested in Hawaii-1969

Treesearch

Robert E. Burgan; Jr. Wesley H.C. Wong

1971-01-01

Primary forest products harvested in Hawaii in 1969 were valued at $331,000-a $3,000 drop from the value of the harvest surveyed in 1967. Sawlogs and veneer logs were the most important products. Koa and robusta eucalyptus were the primary sawlog species. Albizia and robusta eucalyptus provided most of the veneer logs.

Quaternion Based Thermal Condition Monitoring System

NASA Astrophysics Data System (ADS)

Wong, Wai Kit; Loo, Chu Kiong; Lim, Way Soong; Tan, Poi Ngee

In this paper, we will propose a new and effective machine condition monitoring system using log-polar mapper, quaternion based thermal image correlator and max-product fuzzy neural network classifier. Two classification characteristics namely: peak to sidelobe ratio (PSR) and real to complex ratio of the discrete quaternion correlation output (p-value) are applied in the proposed machine condition monitoring system. Large PSR and p-value observe in a good match among correlation of the input thermal image with a particular reference image, while small PSR and p-value observe in a bad/not match among correlation of the input thermal image with a particular reference image. In simulation, we also discover that log-polar mapping actually help solving rotation and scaling invariant problems in quaternion based thermal image correlation. Beside that, log-polar mapping can have a two fold of data compression capability. Log-polar mapping can help smoother up the output correlation plane too, hence makes a better measurement way for PSR and p-values. Simulation results also show that the proposed system is an efficient machine condition monitoring system with accuracy more than 98%.

Beam wander of dark hollow, flat-topped and annular beams

NASA Astrophysics Data System (ADS)

Eyyuboğlu, H. T.; Çil, C. Z.

2008-11-01

Benefiting from the earlier derivations for the Gaussian beam, we formulate beam wander for dark hollow (DH) and flat-topped (FT) beams, also covering the annular Gaussian (AG) beam as a special case. Via graphical illustrations, beam wander variations of these beams are analyzed and compared among themselves and to the fundamental Gaussian beam against changes in propagation length, amplitude factor, source size, wavelength of operation, inner and outer scales of turbulence. These comparisons show that in relation to the fundamental Gaussian beam, DH and FT beams will exhibit less beam wander, particularly at small primary beam source sizes, lower amplitude factors of the secondary beam and higher beam orders. Furthermore, DH and FT beams will continue to preserve this advantageous position all throughout the considered range of wavelengths, inner and outer scales of turbulence. FT beams, in particular, are observed to have the smallest beam wander values among all, up to certain source sizes.

FT-IR spectrum of grape seed oil and quantum models of fatty acids triglycerides

NASA Astrophysics Data System (ADS)

Berezin, K. V.; Antonova, E. M.; Shagautdinova, I. T.; Chernavina, M. L.; Dvoretskiy, K. N.; Grechukhina, O. N.; Vasilyeva, L. M.; Rybakov, A. V.; Likhter, A. M.

2018-04-01

FT-IR spectra of grape seed oil and glycerol were registered in the 650-4000 cm-1 range. Molecular models of glycerol and some fatty acids that compose the oil under study - linoleic, oleic, palmitic and stearic acids - as well as their triglycerides were developed within B3LYP/6-31G(d) density functional model. A vibrating FT-IR spectrum of grape seed oil was modeled on the basis of calculated values of vibrating wave numbers and IR intensities of the fatty acids triglycerides and with regard to their percentage. Triglyceride spectral bands that were formed by glycerol linkage vibrations were revealed. It was identified that triglycerol linkage has a small impact on the structure of fatty acids and, consequently, on vibrating wave numbers. The conducted molecular modeling became a basis for theoretical interpretation on 10 experimentally observed absorption bands in FT-IR spectrum of grape seed oil.

A New N-methoxypyridone from the Co-Cultivation of Hawaiian Endophytic Fungi Camporesia sambuci FT1061 and Epicoccum sorghinum FT1062.

PubMed

Li, Chunshun; Sarotti, Ariel M; Yang, Baojun; Turkson, James; Cao, Shugeng

2017-07-12

A new N -methoxypyridone analog ( 1 ), together with four known compounds, was isolated from the co-culture of Hawaiian endophytic fungi Camporesia sambuci FT1061 and Epicoccum sorghinum FT1062. The structure of the new compound was elucidated as 11 S -hydroxy-1-methoxyfusaricide ( 1 ) by extensive spectroscopic analysis and comparison with the literature. The absolute configuration of 1 was determined by comparison with the experimental and calculated ECD spectra. The absolute configuration of compound 3 was investigated and renamed as (+)-epipyridone by comparison of the optical rotation and CD spectrum with those of 1 . The other known compounds were identified as epicoccarine B ( 2 ), D8646-2-6 ( 4 ), and iso-D8646-2-6 ( 5 ). Compounds 4 and 5 showed modest inhibitory activity towards pathogenic fungi. Epicoccarine B ( 2 ) inhibited A2780 and TK-10 with an IC 50 value of 22 μM.

Sex Differences in the Association between Serum Levels of Testosterone and Frailty in an Elderly Population: The Toledo Study for Healthy Aging

PubMed Central

Carcaillon, Laure; Blanco, Carmen; Alonso-Bouzón, Cristina; Alfaro-Acha, Ana; Garcia-García, Francisco-José; Rodriguez-Mañas, Leocadio

2012-01-01

Background Age-associated decline in testosterone levels represent one of the potential mechanisms involved in the development of frailty. Although this association has been widely reported in older men, very few data are available in women. We studied the association between testosterone and frailty in women and assessed sex differences in this relationship. Methods We used cross-sectional data from the Toledo Study for Healthy Aging, a population-based cohort study of Spanish elderly. Frailty was defined according to Fried's approach. Multivariate odds-ratios (OR) and 95% confidence intervals (CI) associated with total (TT) and free testosterone (FT) levels were estimated using polytomous logistic regression. Results In women, there was a U-shaped relationship between FT levels and frailty (p for FT2 = 0.03). In addition, very low levels of FT were observed in women with ≥4 frailty criteria (age-adjusted geometric means = 0.13 versus 0.37 in subjects with <4 components, p = 0.010). The association of FT with frailty appeared confined to obese women (p-value for interaction = 0.05).In men, the risk of frailty levels linearly decreased with testosterone (adjusted OR for frailty = 2.9 (95%CI, 1.6–5.1) and 1.6 (95%CI, 1.0–2.5), for 1 SD decrease in TT and FT, respectively). TT and FT showed association with most of frailty criteria. No interaction was found with BMI. Conclusion There is a relationship between circulating levels of FT and frailty in older women. This relation seems to be modulated by BMI. The relevance and the nature of the association of FT levels and frailty are sex-specific, suggesting that different biological mechanisms may be involved. PMID:22403651

Veneer recovery from peeler-grade Douglas-fir logs in southwestern Oregon.

Treesearch

E.H. Clarke; A.C. Knauss

1957-01-01

With the continued expansion of Douglas-fir plywood production, demand will increase for all grades of peelable logs to supply the industry. Thus, it becomes increasingly important to know the veneer-grade recovery expected so that timber and log values can be more accurately appraised.

Review of log sort yards

Treesearch

John Rusty Dramm; Gerry L. Jackson; Jenny Wong

2002-01-01

This report provides a general overview of current log sort yard operations in the United States, including an extensive literature review and information collected during on-site visits to several operations throughout the nation. Log sort yards provide many services in marketing wood and fiber by concentrating, merchandising, processing, sorting, and adding value to...

Logging a roadside stand to protect scenic values

Treesearch

Philip M. McDonald; Raymond V. Whiteley

1972-01-01

A case study on the Challenge Experimental Forest, California, demonstrated that logging along roadsides need not despoil roadside stands. Nearly every tree was "viewed" before marking. Because of the "special-care" procedures followed, combined logging and slash-disposal cost was about twice that of a single-tree selection cut.

Comparison of irrigation pumpage with change in ground-water storage in the High Plains aquifer in Chase, Dundy, and Perkins counties, Nebraska, 1975-83

USGS Publications Warehouse

Heimes, F.J.; Ferrigno, C.F.; Gutentag, E.D.; Lucky, R.R.; Stephens, D.M.; Weeks, J.B.

1987-01-01

The relation between pumpage and change in storage was evaluated for most of a three-county area in southwestern Nebraska from 1975 through 1983. Initial comparison of the 1975-83 pumpage with change in storage in the study area indicated that the 1 ,042,300 acre-ft of change in storage was only about 30% of the 3,425,000 acre-ft of pumpage. An evaluation of the data used to calculate pumpage and change in storage indicated that there was a relatively large potential for error in estimates of specific yield. As a result, minimum and maximum values of specific yield were estimated and used to recalculate change in storage. Estimates also were derived for the minimum and maximum amounts of recharge that could occur as a result of cultivation practices. The minimum and maximum estimates for specific yield and for recharge from cultivation practices were used to compute a range of values for the potential amount of additional recharge that occurred as a result of irrigation. The minimum and maximum amounts of recharge that could be caused by irrigation in the study area were 953,200 acre-ft (28% of pumpage) and 2,611,200 acre-ft (76% of pumpage), respectively. These values indicate that a substantial percentage of the water pumped from the aquifer is resupplied to storage in the aquifer as a result of a combination of irrigation return flow and enhanced recharge from precipitation that results from cultivation and irrigation practices. (Author 's abstract)

QSPR study of polychlorinated diphenyl ethers by molecular electronegativity distance vector (MEDV-4).

PubMed

Sun, Lili; Zhou, Liping; Yu, Yu; Lan, Yukun; Li, Zhiliang

2007-01-01

Polychlorinated diphenyl ethers (PCDEs) have received more and more concerns as a group of ubiquitous potential persistent organic pollutants (POPs). By using molecular electronegativity distance vector (MEDV-4), multiple linear regression (MLR) models are developed for sub-cooled liquid vapor pressures (P(L)), n-octanol/water partition coefficients (K(OW)) and sub-cooled liquid water solubilities (S(W,L)) of 209 PCDEs and diphenyl ether. The correlation coefficients (R) and the leave-one-out cross-validation (LOO) correlation coefficients (R(CV)) of all the 6-descriptor models for logP(L), logK(OW) and logS(W,L) are more than 0.98. By using stepwise multiple regression (SMR), the descriptors are selected and the resulting models are 5-descriptor model for logP(L), 4-descriptor model for logK(OW), and 6-descriptor model for logS(W,L), respectively. All these models exhibit excellent estimate capabilities for internal sample set and good predictive capabilities for external samples set. The consistency between observed and estimated/predicted values for logP(L) is the best (R=0.996, R(CV)=0.996), followed by logK(OW) (R=0.992, R(CV)=0.992) and logS(W,L) (R=0.983, R(CV)=0.980). By using MEDV-4 descriptors, the QSPR models can be used for prediction and the model predictions can hence extend the current database of experimental values.

What loggers leave behind: Impacts on big-leaf mahogany (Swietenia macrophylla) commercial populations and potential for post-logging recovery in the Brazilian Amazon.

Treesearch

James Grogan; Stephen B. Jennings; R. Matthew Landis; Mark Schulze; Anadilza M.V. Baima; do Carmo A. Lopes J.; Julian M. Norghauer; L. Rog& eacute Oliveira; rio; Frank Pantoja; Diane Pinto; Jose Natalino M. Silva; Edson Vidal; Barbara L. Zimmerman

2008-01-01

The sustainability of current harvest practices for high-value Meliaceae can be assessed by quantifying logging intensity and projecting growth and survival by post-logging populations over anticipated intervals between harvests. From 100%-area inventories of big-leaf mahogany (Swietenia macrophylla) covering 204 ha or more at eight logged and unlogged forest sites...

Potential advantages of curve sawing non-straight hardwood logs

Treesearch

Philip A. Araman

2007-01-01

Curve sawing is not new to the softwood industry. Softwood sawmill managers think about how fast they can push logs through their sawmill to maximize the yield of 1x and 2x lumber. Curve sawing helps mills maximize yield when sawing non-straight logs. Hardwood sawmill managers don’t want to push logs through their sawmills, because they want to maximize lumber value...

Preliminary Results From the Chicxulub Post-Impact Sediments: XRF and Physical Properties Data

NASA Astrophysics Data System (ADS)

Gebhardt, C.; Perez-Cruz, L. L.; Chenot, É.; Christeson, G. L.; Le Ber, E.; Lofi, J.; Nixon, C.; Rae, A.; Expedition 364 Science Party, I. I.

2017-12-01

In spring 2016, joint IODP/ICDP Expedition 364 drilled into the peak ring of the Chicxulub crater, offshore the Yucatan Peninsula, Mexico. A continuous core was drilled (Hole M0077A) and recovered a sequence of Paleogene post-impact rocks, suevites, impact-melt rocks and granitic basement between 505.7 m and 1334.7 m below sea floor (bsf). The Chicxulub crater was formed 66 million years ago by an impact. This catastrophic event was directly linked to a major mass extinction. For this study, we concentrate on the post-impact sediments (505.7 to 617.3 m bsf; 48 to 66 Ma). The main goal of drilling the post-impact section was to study the pace and mode of recovery of life in the ocean after the impact, and to analyze the paleoenvironmental changes across the Paleocene and Eocene. The late Paleocene and Eocene are characterized by a series of transient warming events, so-called hyperthermals that were associated with increased atmospheric pCO2. Here, we present preliminary geochemical and physical properties data from the 112 m of Paleogene sediments. XRF data show high log (Ca/Ti) values between 617 and 598 m bsf (Paleocene and early Eocene), and lower values between 598 and 505 m bsf. In particular the upper part is characterized by high-frequency fluctuations in log (Ca/Ti) reflecting repeated changes in lithology. These were presumably caused by Milankovitch cycles. Low log (Ba/Ti) values characterize the lowermost part of the record between 617 and 610, followed by a gradual increase to higher values, presumably indicating an increase in primary productivity towards the end of the Paleocene. Values remain at this higher level between 605 and 540 m bsf. Hyperthermals are characterized by strong positive log (Ba/Ti) peaks, likely pointing at highly elevated primary productivity levels during these short-lived events. Between 540 and 505 m bsf, log (Ba/Ti) values are more variable and drop occasionally to values as low as were encountered in the lowermost part. Similar to the log Ca/Ti curve, the log Ba/Ti curve is superimposed by high-frequency fluctuations. These fluctuations are also strongly visible in color reflectance measurements.

Is skin penetration a determining factor in skin sensitization ...

EPA Pesticide Factsheets

Summary:Background. It is widely accepted that substances that cannot penetrate through the skin will not be sensitisers. Thresholds based on relevant physicochemical parameters such as a LogKow > 1 and a MW 1 is a true requirement for sensitisation.Methods. A large dataset of substances that had been evaluated for their skin sensitisation potential, together with measured LogKow values was compiled from the REACH database. The incidence of skin sensitisers relative to non-skin sensitisers below and above the LogKow = 1 threshold was evaluated. Results. 1482 substances with associated skin sensitisation outcomes and measured LogKow values were identified. 305 substances had a measured LogKow < 0 and of those, 38 were sensitisers.Conclusions. There was no significant difference in the incidence of skin sensitisation above and below the LogKow = 1 threshold. Reaction chemistry considerations could explain the skin sensitisation observed for the 38 sensitisers with a LogKow < 0. The LogKow threshold is a self-evident truth borne out from the widespread misconception that the ability to efficiently penetrate the stratum corneum is a key determinant of skin sensitisation potential and potency. Using the REACH data extracted to test out the validity of common assumptions in the skin sensitization AOP. Builds on trying to develop a proof of concept IATA

Accurate control of a liquid-crystal display to produce a homogenized Fourier transform for holographic memories.

PubMed

Márquez, Andrés; Gallego, Sergi; Méndez, David; Alvarez, Mariela L; Fernández, Elena; Ortuño, Manuel; Neipp, Cristian; Beléndez, Augusto; Pascual, Inmaculada

2007-09-01

We show an accurate procedure to obtain a Fourier transform (FT) with no dc term using a commercial twisted-nematic liquid-crystal display. We focus on the application to holographic storage of binary data pages, where a drastic decrease of the dc term in the FT is highly desirable. Two different codification schemes are considered: binary pi radians phase modulation and hybrid ternary modulation. Any deviation in the values of the amplitude and phase shift generates the appearance of a strong dc term. Experimental results confirm that the calculated configurations provide a FT with no dc term, thus showing the effectiveness of the proposal.

An approach to derive some simple empirical equations to calibrate nuclear and acoustic well logging tools.

PubMed

Mohammad Al Alfy, Ibrahim

2018-01-01

A set of three pads was constructed from primary materials (sand, gravel and cement) to calibrate the gamma-gamma density tool. A simple equation was devised to convert the qualitative cps values to quantitative g/cc values. The neutron-neutron porosity tool measures the qualitative cps porosity values. A direct equation was derived to calculate the porosity percentage from the cps porosity values. Cement-bond log illustrates the cement quantities, which surround well pipes. This log needs a difficult process due to the existence of various parameters, such as: drilling well diameter as well as internal diameter, thickness and type of well pipes. An equation was invented to calculate the cement percentage at standard conditions. This equation can be modified according to varying conditions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Determination of reversed-phase high performance liquid chromatography based octanol-water partition coefficients for neutral and ionizable compounds: Methodology evaluation.

PubMed

Liang, Chao; Qiao, Jun-Qin; Lian, Hong-Zhen

2017-12-15

Reversed-phase liquid chromatography (RPLC) based octanol-water partition coefficient (logP) or distribution coefficient (logD) determination methods were revisited and assessed comprehensively. Classic isocratic and some gradient RPLC methods were conducted and evaluated for neutral, weak acid and basic compounds. Different lipophilicity indexes in logP or logD determination were discussed in detail, including the retention factor logk w corresponding to neat water as mobile phase extrapolated via linear solvent strength (LSS) model from isocratic runs and calculated with software from gradient runs, the chromatographic hydrophobicity index (CHI), apparent gradient capacity factor (k g ') and gradient retention time (t g ). Among the lipophilicity indexes discussed, logk w from whether isocratic or gradient elution methods best correlated with logP or logD. Therefore logk w is recommended as the preferred lipophilicity index for logP or logD determination. logk w easily calculated from methanol gradient runs might be the main candidate to replace logk w calculated from classic isocratic run as the ideal lipophilicity index. These revisited RPLC methods were not applicable for strongly ionized compounds that are hardly ion-suppressed. A previously reported imperfect ion-pair RPLC method was attempted and further explored for studying distribution coefficients (logD) of sulfonic acids that totally ionized in the mobile phase. Notably, experimental logD values of sulfonic acids were given for the first time. The IP-RPLC method provided a distinct way to explore logD values of ionized compounds. Copyright © 2017 Elsevier B.V. All rights reserved.

High-precision branching-ratio measurement for the superallowed β+ emitter 74Rb

NASA Astrophysics Data System (ADS)

Dunlop, R.; Ball, G. C.; Leslie, J. R.; Svensson, C. E.; Towner, I. S.; Andreoiu, C.; Chagnon-Lessard, S.; Chester, A.; Cross, D. S.; Finlay, P.; Garnsworthy, A. B.; Garrett, P. E.; Glister, J.; Hackman, G.; Hadinia, B.; Leach, K. G.; Rand, E. T.; Starosta, K.; Tardiff, E. R.; Triambak, S.; Williams, S. J.; Wong, J.; Yates, S. W.; Zganjar, E. F.

2013-10-01

A high-precision branching-ratio measurement for the superallowed β+ decay of 74Rb was performed at the TRIUMF Isotope Separator and Accelerator (ISAC) radioactive ion-beam facility. The scintillating electron-positron tagging array (SCEPTAR), composed of 10 thin plastic scintillators, was used to detect the emitted β particles; the 8π spectrometer, an array of 20 Compton-suppressed HPGe detectors, was used for detecting γ rays that were emitted following Gamow-Teller and nonanalog Fermi β+ decays of 74Rb; and the Pentagonal Array of Conversion Electron Spectrometers (PACES), an array of 5 Si(Li) detectors, was employed for measuring β-delayed conversion electrons. Twenty-three excited states were identified in 74Kr following 8.241(4)×108 detected 74Rb β decays. A total of 58 γ-ray and electron transitions were placed in the decay scheme, allowing the superallowed branching ratio to be determined as B0=99.545(31)%. Combined with previous half-life and Q-value measurements, the superallowed branching ratio measured in this work leads to a superallowed ft value of 3082.8(65) s. Comparisons between this superallowed ft value and the world-average-corrected Ft¯ value, as well as the nonanalog Fermi branching ratios determined in this work, provide guidance for theoretical models of the isospin-symmetry-breaking corrections in this mass region.

Half-life, branching-ratio, and Q-value measurement for the superallowed 0{sup +}{yields}0{sup +}{beta}{sup +} emitter {sup 42}Ti

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nieto, T. Kurtukian; Souin, J.; Audirac, L.

2009-09-15

The half-life, the branching ratio, and the decay Q value of the superallowed {beta} emitter {sup 42}Ti were measured in an experiment performed at the JYFLTRAP facility of the Accelerator Laboratory of the University of Jyvaeskylae. {sup 42}Ti is the heaviest T{sub z}=-1 nucleus for which high-precision measurements of these quantities have been tried. The half-life (T{sub 1/2}=208.14{+-}0.45 ms) and the Q value [Q{sub EC}=7016.83(25) keV] are close to or reach the required precision of about 0.1%. The branching ratio for the superallowed decay branch [BR=47.7(12)%], a by-product of the half-life measurement, does not reach the necessary precision yet. Nonetheless,more » these results allow one to determine the experimental ft value and the corrected Ft value to be 3114(79) and 3122(79) s, respectively.« less

26 CFR 1.684-3 - Exceptions to general rule of gain recognition.

Code of Federal Regulations, 2013 CFR

2013-04-01

... to 400X to FT. At the time of the transfer, FT has a U.S. beneficiary within the meaning of § 1.679-2... not cause A to recognize gain at the time of the transfer. See § 1.684-2(e) for rules that may require... gain at that time under § 1.684-1. Example 4. Transfer of property for fair market value to an...

26 CFR 1.684-3 - Exceptions to general rule of gain recognition.

Code of Federal Regulations, 2012 CFR

2012-04-01

... to 400X to FT. At the time of the transfer, FT has a U.S. beneficiary within the meaning of § 1.679-2... not cause A to recognize gain at the time of the transfer. See § 1.684-2(e) for rules that may require... gain at that time under § 1.684-1. Example 4. Transfer of property for fair market value to an...

Effects of 4 Weeks of High-Intensity Interval Training and β-Hydroxy-β-Methylbutyric Free Acid Supplementation on the Onset of Neuromuscular Fatigue.

PubMed

Miramonti, Amelia A; Stout, Jeffrey R; Fukuda, David H; Robinson, Edward H; Wang, Ran; La Monica, Michael B; Hoffman, Jay R

2016-03-01

This study investigated the effects of high-intensity interval training (HIIT) and β-hydroxy-β-methylbutyric free acid (HMB) supplementation on physical working capacity at the onset of neuromuscular fatigue threshold (PWC(FT)). Thirty-seven participants (22 men, 15 women; 22.8 ± 3.4 years) completed an incremental cycle ergometer test (graded exercise test [GXT]); electromyographic amplitude from the right vastus lateralis was recorded. Assessments occurred preceding (PRE) and after 4 weeks of supplementation (POST). Participants were randomly assigned to control (C, n = 9), placebo (P, n = 14), or supplementation (S, n = 14) groups. Both P and S completed 12 HIIT sessions, whereas C maintained normal diet and activity patterns. The PWC(FT) (W) was determined using the maximal perpendicular distance (D(MAX)) method. Electromyographic amplitude (μVrms) over time was used to generate a cubic regression. Onset of fatigue (TF) was the x-value of the point on the regression that was at D(MAX) from a line between the first and last data points. The PWC(FT) was estimated using TF and GXT power-output increments. The 2-way analysis of variance (ANOVA) (group × time) resulted in a significant interaction for PWC(FT) (F = 6.69, p = 0.004). Post hoc analysis with 1-way ANOVA resulted in no difference in PWC(FT) among groups at PRE (F = 0.87, p = 0.43); however, a difference in PWC(FT) was shown for POST (F = 5.46, p = 0.009). Post hoc analysis among POST values revealed significant differences between S and both P (p = 0.034) and C (p = 0.003). No differences (p = 0.226) were noted between P and C. Paired samples t-tests detected significant changes after HIIT for S (p < 0.001) and P (p = 0.016), but no change in C (p = 0.473). High-intensity interval training increased PWC(FT), but HMB with HIIT was more effective than HIIT alone. Furthermore, it seems that adding HMB supplementation with HIIT in untrained men and women may further improve endurance performance measures.

Synthesis, X-ray crystallography characterization, vibrational spectroscopic, molecular electrostatic potential maps, thermodynamic properties studies of N,N'-di(p-thiazole)formamidine.

PubMed

Rofouei, M K; Fereyduni, E; Sohrabi, N; Shamsipur, M; Attar Gharamaleki, J; Sundaraganesan, N

2011-01-01

In this work, we will report a combined experimental and theoretical study on molecular and vibrational structure of N,N'-di(p-thiazole)formamidine (DpTF). DpTF has been synthesized and characterized by elemental analysis, FT-IR, FT-Raman, 1H NMR, 13C NMR spectroscopy and X-ray single crystal diffraction. The FT-IR and FT-Raman spectra of DpTF were recorded in the solid phase. The optimized geometry was calculated by HF and B3LYP methods using 6-31G(d) basis set. The FT-IR and FT-Raman spectra of DpTF was calculated at the HF/B3LYP/6-31G(d) level and were interpreted in terms of potential energy distribution (PED) analysis. The scaled theoretical wavenumber showed very good agreement with the experimental values. A detailed interpretation of the infrared and Raman spectra of DpTF was reported. On the basis of vibrational analyses, the thermodynamic properties of the title compound at different temperatures have been calculated, revealing the correlations between Cp,m°, Sm°, Hm° and temperatures. Furthermore, molecular electrostatic potential maps (MESP) and total dipole moment properties of the compound have been calculated. Copyright © 2010 Elsevier B.V. All rights reserved.

Effect of microwave treatment on structure of binders based on sodium carboxymethyl starch: FT-IR, FT-Raman and XRD investigations

NASA Astrophysics Data System (ADS)

Kaczmarska, Karolina; Grabowska, Beata; Spychaj, Tadeusz; Zdanowicz, Magdalena; Sitarz, Maciej; Bobrowski, Artur; Cukrowicz, Sylwia

2018-06-01

The paper deals with the influence of the microwave treatment on sodium carboxymethyl starch (CMS-Na) applied as a binder for moulding sands. The Fourier transformation infrared spectrometry (FT-IR), Raman spectroscopy (FT-Raman) and XRD analysis data of native potato starch and three different carboxymethyl starches (CMS-Na) with various degree of substitution (DS) before and after exposition to microwave radiation have been compared. FT-IR studies showed that polar groups present in CMS-Na structure take part in the formation of new hydrogen bonds network after water evaporation. However, these changes depend on DS value of the modified starch. The FT-Raman study confirmed that due to the impact on the samples by microwave, the changes of intensity in the characteristic bands associated with the crystalline regions in the sample were noticed. The X-ray diffraction data for microwave treated CMS-Na samples have been compared with the diffractograms of initial materials and analysis of XRD patterns confirmed that microwave-treated samples exhibit completely amorphous structure. Analysis of structural changes allows to state that the binding of sand grains in moulding sand with CMS-Na polymeric binder consists in the formation of hydrogen bonds networks (physical cross-linking).

Spectroscopic (FT-IR, FT-Raman, NMR and UV-Visible) and quantum chemical studies of molecular geometry, Frontier molecular orbital, NLO, NBO and thermodynamic properties of salicylic acid.

PubMed

Suresh, S; Gunasekaran, S; Srinivasan, S

2014-11-11

The solid phase FT-IR and FT-Raman spectra of 2-hydroxybenzoic acid (salicylic acid) have been recorded in the region 4000-400 and 4000-100 cm(-1) respectively. The optimized molecular geometry and fundamental vibrational frequencies are interpreted with the aid of structure optimizations and normal coordinate force field calculations based on density functional theory (DFT) method and a comparative study between Hartree Fork (HF) method at 6-311++G(d,p) level basis set. The calculated harmonic vibrational frequencies are scaled and they are compared with experimentally obtained FT-IR and FT-Raman spectra. A detailed interpretation of the vibrational spectra of this compound has been made on the basis of the calculated potential energy distribution (PED). The time dependent DFT method is employed to predict its absorption energy and oscillator strength. The linear polarizability (α) and the first order hyper polarizability (β) values of the investigated molecule have been computed. The electronic properties, such as HOMO and LUMO energies, molecular electrostatic potential (MEP) are also performed. Stability of the molecule arising from hyper conjugative interaction, charge delocalization has been analyzed using natural bond orbital (NBO) analysis. Published by Elsevier B.V.

Effect of microwave treatment on structure of binders based on sodium carboxymethyl starch: FT-IR, FT-Raman and XRD investigations.

PubMed

Kaczmarska, Karolina; Grabowska, Beata; Spychaj, Tadeusz; Zdanowicz, Magdalena; Sitarz, Maciej; Bobrowski, Artur; Cukrowicz, Sylwia

2018-06-15

The paper deals with the influence of the microwave treatment on sodium carboxymethyl starch (CMS-Na) applied as a binder for moulding sands. The Fourier transformation infrared spectrometry (FT-IR), Raman spectroscopy (FT-Raman) and XRD analysis data of native potato starch and three different carboxymethyl starches (CMS-Na) with various degree of substitution (DS) before and after exposition to microwave radiation have been compared. FT-IR studies showed that polar groups present in CMS-Na structure take part in the formation of new hydrogen bonds network after water evaporation. However, these changes depend on DS value of the modified starch. The FT-Raman study confirmed that due to the impact on the samples by microwave, the changes of intensity in the characteristic bands associated with the crystalline regions in the sample were noticed. The X-ray diffraction data for microwave treated CMS-Na samples have been compared with the diffractograms of initial materials and analysis of XRD patterns confirmed that microwave-treated samples exhibit completely amorphous structure. Analysis of structural changes allows to state that the binding of sand grains in moulding sand with CMS-Na polymeric binder consists in the formation of hydrogen bonds networks (physical cross-linking). Copyright © 2018 Elsevier B.V. All rights reserved.

[1,10]Phenanthroline based cyanine dyes as fluorescent probes for ribonucleic acids in live cells

NASA Astrophysics Data System (ADS)

Kovalska, Vladyslava; Kuperman, Marina; Varzatskii, Oleg; Kryvorotenko, Dmytro; Kinski, Elisa; Schikora, Margot; Janko, Christina; Alexiou, Christoph; Yarmoluk, Sergiy; Mokhir, Andriy

2017-12-01

A series of monomethine, trimethine- and styrylcyanine dyes based on a [1,10]phenanthroline moiety was synthesized, characterized and investigated as potential fluorescent probes for nucleic acids in cell free settings and in cells. The dyes were found to be weakly fluorescent in the unbound state, whereas upon the binding to dsDNA or RNA their emission intensity raised up to 50 times (for monomethine benzothiazole derivative FT1 complexed with RNA). The strongest fluorescence intensity in assemblies with dsDNA and RNA was observed for the trimethine benzothiazole derivative FT4. The quantum yield of FT4 fluorescence in its complex with dsDNA was found to be 1.5% and the binding constant (K b) was estimated to be 7.9 × 104 M-1 that is a typical value for intercalating molecules. The FT4 dye was found to be cell membrane permeable. It stains RNA rich components—the nucleoli and most probably the cytoplasmic RNA. FT4 bound to RNAs delivers a very strong fluorescence signal, which makes this easily accessible dye a potentially useful alternative to known RNA stains, e.g. expensive SYTO® 83. The advantage of FT4 is its easy synthetic access including no chromatographic purification steps, which will be reflected in its substantially lower price.

Lipophilicity assessment of basic drugs (log P(o/w) determination) by a chromatographic method.

PubMed

Pallicer, Juan M; Sales, Joaquim; Rosés, Martí; Ràfols, Clara; Bosch, Elisabeth

2011-09-16

A previously reported chromatographic method to determine the 1-octanol/water partition coefficient (log P(o/w)) of organic compounds is used to estimate the hydrophobicity of bases, mainly commercial drugs with diverse chemical nature and pK(a) values higher than 9. For that reason, mobile phases buffered at high pH to avoid the ionization of the solutes and three different columns (Phenomenex Gemini NX, Waters XTerra RP-18 and Waters XTerra MS C(18)) with appropriate alkaline-resistant stationary phases have been used. Non-ionizable substances studied in previous works were also included in the set of compounds to evaluate the consistency of the method. The results showed that all the columns provide good estimations of the log P(o/w) for most of the compounds included in this study. The Gemini NX column has been selected to calculate log P(o/w) values of the set of studied drugs, and really good correlations between the determined log P(o/w) values and those considered as reference were obtained, proving the ability of the procedure for the lipophilicity assessment of bioactive compounds with very different structures and functionalities. Copyright © 2011 Elsevier B.V. All rights reserved.

Water-level altitudes 2016 and water-level changes in the Chicot, Evangeline, and Jasper aquifers and compaction 1973–2015 in the Chicot and Evangeline aquifers, Houston-Galveston region, Texas

USGS Publications Warehouse

Kasmarek, Mark C.; Ramage, Jason K.; Johnson, Michaela R.

2016-10-07

Most of the land-surface subsidence in the Houston-Galveston region, Texas, has occurred as a direct result of groundwater withdrawals for municipal supply, commercial and industrial use, and irrigation that depressured and dewatered the Chicot and Evangeline aquifers, thereby causing compaction of the aquifer sediments, mostly in the fine-grained silt and clay layers. This report, prepared by the U.S. Geological Survey in cooperation with the Harris-Galveston Subsidence District, City of Houston, Fort Bend Subsidence District, Lone Star Groundwater Conservation District, and Brazoria County Groundwater Conservation District, is one in an annual series of reports depicting water-level altitudes and water-level changes in the Chicot, Evangeline, and Jasper aquifers and measured cumulative compaction of subsurface sediments in the Chicot and Evangeline aquifers in the Houston-Galveston region. The report contains regional-scale maps depicting approximate 2016 water-level altitudes (represented by measurements made during December 2015–March 2016) for the Chicot, Evangeline, and Jasper aquifers; maps depicting 1-year (2015–16) water-level changes for each aquifer; maps depicting approximate contoured 5-year (2011–16) water-level changes for each aquifer; maps depicting approximate contoured long-term (1990–2016 and 1977–2016) water-level changes for the Chicot and Evangeline aquifers; a map depicting approximate contoured long-term (2000–16) water-level changes for the Jasper aquifer; a map depicting locations of borehole-extensometer sites; and graphs depicting measured long-term cumulative compaction of subsurface sediments at the extensometers during 1973–2015. Tables listing the water-level data used to construct each water-level map for each aquifer and the measured long-term cumulative compaction data for each extensometer site are included. Graphs depicting water-level measurement data also are included; these graphs can be used to approximate changes in effective stress caused by changes in groundwater withdrawal from the Chicot and Evangeline aquifers.In 2016, water-level-altitude contours for the Chicot aquifer ranged from 200 feet (ft) below the vertical datum (North American Vertical Datum of 1988; hereinafter, datum) in a localized area in northwestern Harris County to 200 ft above datum in west-central Montgomery County. Water-level changes during 2015–16 in the Chicot aquifer ranged from a 39-ft decline to a 26-ft rise. Contoured 5-year and long-term changes in water-level altitudes of the Chicot aquifer ranged from a 30-ft decline to a 20-ft rise (2011–16), from a 140-ft decline to a 160-ft rise (1990–2016), and from a 120-ft decline to a 200-ft rise (1977–2016). In 2016, water-level-altitude contours for the Evangeline aquifer ranged from 250 ft below datum in three separate areas in south-central Montgomery County and extending into north-central Harris County, in west-central Harris County, and in southwestern Harris County to 200 ft above datum in southeastern Grimes and northwestern Montgomery Counties. Water-level changes during 2015–16 in the Evangeline aquifer ranged from a 65-ft decline to a 61-ft rise. Contoured 5-year and long-term changes in water-level altitudes of the Evangeline aquifer ranged from a 60-ft decline to a 40-ft rise (2011–16), from a 160-ft decline to a 160-ft rise (1990–2016), and from a 320-ft decline to a 240-ft rise (1977–2016). In 2016, water-level-altitude contours for the Jasper aquifer ranged from 200 ft below datum in south-central Montgomery County extending into north-central Harris County to 250 ft above datum in northwestern Montgomery County and extending into eastern Grimes County and southwestern Walker County. Water-level changes during 2015–16 in the Jasper aquifer ranged from a 38-ft decline to a 51-ft rise. Contoured 5-year and long-term changes in water-level altitudes of the Jasper aquifer ranged from a 60-ft decline to a 40-ft rise (2011–16) and from a 220-ft decline to a 20-ft decline (2000–16).Compaction of subsurface sediments (mostly in the fine-grained silt and clay layers) in the Chicot and Evangeline aquifers was recorded continuously by using 13 extensometers at 11 sites that were either activated or installed between 1973 and 1980. During the period of record beginning in 1973 (or later depending on activation or installation date) and ending in December 2015, measured cumulative compaction at the 13 extensometers ranged from 0.095 ft at the Texas City-Moses Lake extensometer to 3.666 ft at the Addicks extensometer. From January through December 2015, the Northeast, Southwest, Addicks, Johnson Space Center, and Clear Lake (deep) extensometers recorded net decreases in land-surface elevation, but the Lake Houston, East End, Texas City-Moses Lake, Baytown C–1 (shallow), Baytown C–2 (deep), Seabrook, Clear Lake (shallow), and Pasadena extensometers recorded net increases in land-surface elevation. For the 11 extensometer sites during the selected years 1988, 1998, 2008, 2012, and 2015, the smallest effective stress (20.12 pounds per square inch [psi]) was estimated at the Texas City-Moses Lake extensometer site and was produced by a measured water level of 46.42 ft below land-surface datum (blsd) in January 2008. The corresponding net compaction during 2007 at this site was 0.001 ft. The largest effective stress (174.86 psi) was estimated at the Addicks extensometer site and was produced by a measured water level of 403.38 ft blsd in January 1998. The corresponding net compaction at the Addicks site was 0.067 ft in 1997.The 2011 drought caused water-level declines in the aquifers that were documented by the water-level-measurement data collected in January 2012. During the 2011 drought, the 13 extensometers recorded varying amounts of compaction that ranged from a net compaction value of 0.002 ft recorded by the Texas City-Moses Lake extensometer to a net compaction value of 0.192 ft recorded by the Pasadena extensometer. Water-level data for 1988, 1998, 2008, 2012, and 2015 and the corresponding net compaction values recorded by the extensometers for 1987, 1997, 2007, 2011, and 2014 were used to illustrate the cause and effect relations between changes in water level caused by groundwater withdrawals and resulting changes in effective stress. Changes in effective stress are related to changes in land-surface elevations caused by compaction of the fine-grained sediments composing the Chicot and Evangeline aquifers.The rate of compaction varies from site to site because of differences in rates of groundwater withdrawal in the areas adjacent to each extensometer site; differences among sites in the ratios of sand, silt, and clay and their corresponding compressibilities; and previously established preconsolidation heads. It is not appropriate, therefore, to extrapolate or infer a rate of compaction for an adjacent area on the basis of the rate of compaction recorded by proximal extensometers.

CRYPTOSPORIDIUM LOG-INACTIVATION WITH OZONE USING EFFLUENT CT 10, GEOMETRIC MEAN CT 10 EXTENDED INTEGRATED CT 10 AND EXTENDED-CSTR CALCULATIONS

EPA Science Inventory

The draft Long Term 2 Enhanced Surface Water Treatment Rule ("LT2ESWTR") contains Cryptosporidium log-inactivation CT tables. Depending on the water temperature, the Cryptosporidium CT values that are listed are 15 to 25 times greater than CT values fo...

Conceptual and numerical models of the glacial aquifer system north of Aberdeen, South Dakota

USGS Publications Warehouse

Marini, Katrina A.; Hoogestraat, Galen K.; Aurand, Katherine R.; Putnam, Larry D.

2012-01-01

This U.S. Geological Survey report documents a conceptual and numerical model of the glacial aquifer system north of Aberdeen, South Dakota, that can be used to evaluate and manage the city of Aberdeen's water resources. The glacial aquifer system in the model area includes the Elm, Middle James, and Deep James aquifers, with intervening confining units composed of glacial till. The Elm aquifer ranged in thickness from less than 1 to about 95 feet (ft), with an average thickness of about 24 ft; the Middle James aquifer ranged in thickness from less than 1 to 91 ft, with an average thickness of 13 ft; and the Deep James aquifer ranged in thickness from less than 1 to 165 ft, with an average thickness of 23 ft. The confining units between the aquifers consisted of glacial till and ranged in thickness from 0 to 280 ft. The general direction of groundwater flow in the Elm aquifer in the model area was from northwest to southeast following the topography. Groundwater flow in the Middle James aquifer was to the southeast. Sparse data indicated a fairly flat potentiometric surface for the Deep James aquifer. Horizontal hydraulic conductivity for the Elm aquifer determined from aquifer tests ranged from 97 to 418 feet per day (ft/d), and a confined storage coefficient was determined to be 2.4x10-5. Estimates of the vertical hydraulic conductivity of the sediments separating the Elm River from the Elm aquifer, determined from the analysis of temperature gradients, ranged from 0.14 to 2.48 ft/d. Average annual precipitation in the model area was 19.6 inches per year (in/yr), and agriculture was the primary land use. Recharge to the Elm aquifer was by infiltration of precipitation through overlying outwash, lake sediments, and glacial till. The annual recharge for the model area, calculated by using a soil-water-balance method for water year (WY) 1975-2009, ranged from 0.028 inch in WY 1980 to 4.52 inches in WY 1986, with a mean of 1.56 inches. The annual potential evapotranspiration, calculated in soil-water-balance analysis, ranged from 21.8 inches in WY 1983 to 27.0 inches in WY 1985, with a mean of 24.6 inches. Water use from the glacial aquifer system primarily was from the Elm aquifer for irrigation, municipal, and suburban water supplies, and the annual rate ranged from 1.0 to 2.4 cubic feet per second (ft3/s). The MODFLOW-2005 numerical model represented the Elm aquifer, the Middle James aquifer, and the Deep James aquifer with model layers 1-3 respectively separated by confining layers 1-2 respectively. Groundwater flow was simulated with 75 stress periods beginning October 1, 1974, and ending September 30, 2009. Model grid spacing was 200 by 200 ft and boundaries were represented by specified-head boundaries and no-flow boundaries. The model used parameter estimation that focused on minimizing the difference between 954 observed and simulated hydraulic heads for 135 wells. Calibrated mean horizontal hydraulic conductivity values for model layers 1-3 were 94, 41, and 30 ft/d respectively. Vertical hydraulic conductivity values for confining layers 1 and 2 were 0.0002 and 0.0003 ft/d, respectively. Calibrated specific yield for model layer 1was 0.1 and specific storage ranged from 0.0003 to 0.0005 per foot. Calibrated mean recharge rates ranged from 2.5 in/yr where glacial till thickness was less than 10 ft to 0.8 in/yr where glacial till thickness was greater than 30 ft. Calibrated mean annual evapotranspiration rate was 8.8 in/yr. Simulated net streamflow gain from model layer 1 was 3.1 ft3/s.

Hydrogeological investigation at Site 5, Willow Grove Naval Air Station/Joint Reserve Base, Horsham Township, Montgomery County, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.

2002-01-01

The U.S. Geological Survey conducted borehole geophysical logging, collected and analyzed water-level data, and sampled sections of a rock core to determine the concentration of volatile organic compounds in the aquifer matrix of the Stockton Formation. Borehole geophysical logs were run in three monitor wells. At well 05MW04I, the vertical gradient was upward at depths above 42 feet below land surface (ft bls), downward between 42 and 82 ft bls, and upward below 82 ft bls. At well 05MW05I, a downward vertical gradient was present. At well 05MW12I, the vertical gradient was downward above 112 ft bls and upward below 112 ft bls.Three water-bearing fractures in a 17-foot long rock core from 23.5 to 40.5 ft bls were identified and sampled. Three samples were analyzed from each water-bearing fracture—at the fracture face, 2 centimeters (cm) below the fracture, and 4 cm below the fracture. Fifteen compounds were detected; however, concentrations of seven compounds were less than 1 microgram per kilogram (mg/kg) when detected. Concentrations of benzene (from 0.39 to 3.3 mg/kg), 1,1-dichloroethene (1,1-DCE) (from 0.15 to 13 mg/kg), 1,1,1-trichloroethane (TCA) (from 0.17 to 22 mg/kg), and trichloroethylene (TCE) (from 0.092 to 9.6 mg/kg) were detected in all samples. The highest concentrations detected were for toluene, which was detected at a concentration of 32 and 86 mg/kg in the samples from unweathered sandstone at 2 and 4 cm below the fracture, respectively. Concentrations generally decreased with distance below the fracture in the mudstone samples. Concentrations of benzene and toluene increased with distance below the fractures in the unweathered sandstone samples. Concentrations of 1,1-DCE, TCA, and TCE were higher in the mudstone samples than in the samples from sandstone. Toluene concentrations were higher in unweathered sandstone than in weathered sandstone or mudstone.The effect of the pumping of Horsham Water and Sewer Authority public supply well 26 (HWSA-26), 0.2 mile southwest of the base boundary, on groundwater levels on the base was determined by shutting the well down for 6 days to allow water levels to recover. Water levels in 22 nearby wells were measured. The only well (02MW01I) that showed an unambiguous response to the shutdown of well HWSA-26 is 1,350 feet directly along strike from well HWSA-26. The recovery of well 05MW11I in response to the shutdown of well HWSA-26 is masked by recharge from snowmelt but probably does not exceed about 0.2 feet on the basis of the water level in well 05MW11I, which showed a response to the pumping of well HWSA-26 that ranged from 0.5 to 0.15 foot.Horizontal gradients differ with depth, and the rate and direction of ground-water flow and contaminant movement is depth dependent. The potentiometric-surface map for water levels measured in wells screened between 5 and 44 ft bls in the aquifer shows a ground-water mound that is the high point on a regional ground-water divide. From this divide, ground water flows both northwest toward Park Creek and southeast toward Pennypack Creek. The hydraulic gradient around this mound is relatively flat to the southeast and particularly flat to the northwest. The potentiometric-surface map for water levels measured in wells screened between 40 and 100 ft bls in the aquifer shows a very flat hydraulic gradient. Differences in the elevation of the potentiometric surface are less than 2 feet. The potentiometric-surface map for water levels measured in wells screened between 105 and 179 ft bls in the aquifer shows a steep hydraulic gradient between Sites 5 and 2 and a relatively flat hydraulic gradient between Sites 5 and 3. Water levels measured on October 7, 1999, showed downward vertical head gradients for all well clusters at Site 5. Vertical gradients ranged from 0.01 at well cluster 05MW10 to 0.2 at cluster 05MW11. Most gradients were between 0.01 and 0.026. Vertical head gradients vary with time. The variability is caused by a difference in the magnitude of water-level fluctuations between shallow and the deep fractures. The difference in the magnitude of water-level fluctuations is because of differences in lithology and aquifer storativity.

An analysis technique for testing log grades

Treesearch

Carl A. Newport; William G. O' Regan

1963-01-01

An analytical technique that may be used in evaluating log-grading systems is described. It also provides means of comparing two or more grading systems, or a proposed change with the system from which it was developed. The total volume and computed value of lumber from each sample log are the basic data used.

Computer Integrated Hardwood Processing

Treesearch

Luis G. Occeña; Daniel L. Schmoldt

1997-01-01

The planning of how the hardwood log can be sawn to improve recovery of high-value lumber has always been hampered by the limited information provided by external defects, and whatever internal defects are eventually revealed on the cut log faces by the sawing pattern. With expanded export and domestic markets, low-quality logs, increased competition from non-wood...

Geological studies of the COST nos. G-1 and G-2 wells, United States North Atlantic outer continental shelf

USGS Publications Warehouse

Scholle, Peter A.; Wenkam, Chiye R.

1982-01-01

The COST Nos. G-1 and G-2 wells (fig. 1) are the second and third deep stratigraphic test wells drilled in the North Atlantic Outer Continental Shelf of the United States. COST No. G-1 was drilled in the Georges Bank basin to a total depth of 16,071 ft (4,898 m). G-1 bottomed in phyllite, slate, and metaquartzite overlain by weakly metamorphosed dolomite, all of Cambrian age. From approximately 15,600 to 12,400 ft (4,755 to 3,780 m) the strata are Upper Triassic(?), Lower Jurassic(?), and Middle Jurassic, predominantly red shales, sandstones, and conglomerates. Thin, gray Middle Jurassic beds of shale, sandstone, limestone, and dolomite occur from 12,400 to 9,900 ft (3,780 to 3,018 m). From 9,900 to 1,030 ft (3,018 to 314 m) are coarse-grained unconsolidated sands and loosely cemented sandstones, with beds of gray shale, lignite, and coal. The microfossils indicate the rocks are Upper Jurassic from 10,100 ft (3,078 m) up to 5,400 ft (1,646 m) and Cretaceous from that depth to 1,030 ft (314 m). No younger or shallower rocks were recovered in the drilling at the COST No. G-1 site, but an Eocene limestone is inferred to be disconformable over Santonian strata. The Jurassic strata of the COST No. G-1 well were deposited in shallow marine, marginal marine, and nonmarine environments, which changed to a dominantly shallow marine but still nearshore environment in the Cretaceous. The COST No. G-2 well was drilled 42 statute miles {68 km) east of the G-1 site, still within the Georges Bank basin, to a depth of 21,874 ft (6,667 m). The bottom 40 ft (12 m) of salt and anhydrite is overlain by approximately 7,000 ft {2,134 m) of Upper Triassic{?), Lower Jurassic{?) and Middle Jurassic dolomite, limestone, and interbedded anhydrite from 21,830 to 13,615 ft (6,654 to 4,153 m). From 13,500 to 9,700 ft (4,115 to 2,957 m) are Middle Jurassic limestones with interbedded sandstone. From 9,700 to 4,000 ft (2,957 to 1,219 m) are Upper Jurassic and Cretaceous interbedded sandstones and limestones overlain by Upper Cretaceous unconsolidated sands, sandstones, and calcareous shales. Pliocene, Miocene, Eocene, and Paleocene strata are disconformable over Santonian rocks; uppermost Cretaceous rocks are missing at this site, as at G-1. The sedimentary rocks in the COST No. G-2 well were deposited in somewhat deeper water, farther away from sources of terrigenous material than those at G-l, but still in marginal marine to shallow marine environments. Data from geophysical logs and examination of conventional cores, wellcuttings, and sidewall cores show that below 10,000 ft {3,048 m), the strata in both wells have moderate porosities {< 20 percent) and low to moderate permeabilities {< 100 mD) and are thus considered adequate to poor reservoir rocks. Above 10,000 ft (3,000 m) the porosities range from 16 to 39 percent, and the permeabilities are highly variable, ranging from 0.01 to 7,100 mD. Measurements of vitrinite reflectance, color alteration of visible organic matter, and various organic geochemical properties suggest that the Tertiary and Cretaceous strata of the COST Nos. G-1 and G-2 are not prospective for oil and gas. These sediments have not been buried deeply enough for hydrocarbon generation, and the kerogen and extractable organic matter in them are thermally immature. However, the Jurassic rocks at the G-1 site do contain small amounts of thermally mature gas-prone kerogens. The Jurassic rocks at COST No. G-2 are also gas-prone and are slightly richer in organic carbon and total extractable hydrocarbons than the G-1 rocks, but both sites have only poor to fair oil and gas source-rock potential.

Effect of curve sawing on lumber recovery and warp of short cherry logs containing sweep

Treesearch

Brian H. Bond; Philip Araman

2008-01-01

It has been estimated that approximately one-third of hardwood sawlogs have a significant amount of sweep and that 7 to nearly 40 percent of the yield is lost from logs that have greater than 1 inch of sweep. While decreased yield is important, for hardwood logs the loss of lumber value is likely more significant. A method that produced lumber while accounting for log...

Comparison and relationship of thyroid hormones, IL-6, IL-10 and albumin as mortality predictors in case-mix critically ill patients.

PubMed

Quispe E, Álvaro; Li, Xiang-Min; Yi, Hong

2016-05-01

To compare the ability of thyroid hormones, IL-6, IL-10, and albumin to predict mortality, and to assess their relationship in case-mix acute critically ill patients. APACHE II scores and serum thyroid hormones (FT3, FT4, and TSH), IL-6, IL-10, and albumin were obtained at EICU admission for 79 cases of mix acute critically ill patients without previous history of thyroid disease. Patients were followed for 28 days with patient's death as the primary outcome. All mean values were compared, correlations assessed with Pearson' test, and mortality prediction assessed by multivariate logistic regression and ROC. Non survivors were older, with higher APACHE II score (p=0.000), IL-6 (p<0.05), IL-10 (p=0.000) levels, and lower albumin (p=0.000) levels compared to survivors at 28 days. IL-6 and IL-10 had significant negative correlation with albumin (p=0.001) and FT3 (p ⩽ 0.05) respectively, while low albumin had a direct correlation with FT3 (p<0.05). In the mortality prediction assessment, IL-10, albumin and APACHE II were independent morality predictors and showed to have a good (0.70-0.79) AUC-ROC (p<0.05). Despite that the entire cohort showed low FT3 serum levels (p=0.000), there was not statistical difference between survivors and non-survivors; neither showed any significance as mortality predictor. IL-6 and IL-10 are correlated with Low FT3 and hypoalbuminemia. Thyroid hormones assessed at EICU admission did not have any predictive value in our study. And finally, high levels of IL-6 and IL-10 in conjunction with albumin could improve our ability to evaluate disease's severity and predict mortality in the critically ill patients. When use in combination with APACHE II scores, our model showed improved mortality prediction. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Thyroid hormone concentrations differ between donkeys and horses.

PubMed

Mendoza, F J; Perez-Ecija, R A; Toribio, R E; Estepa, J C

2013-03-01

Reference intervals for thyroid hormones (TH) concentrations have not been previously established for donkeys, leading to potential misdiagnosis of thyroid disease. To determine the normal values of TH in healthy adult donkeys and compare them to TH values from healthy adult horses. Thirty-eight healthy Andalusian donkeys and 19 healthy Andalusian horses from 2 different farms were used. Donkeys were divided into 3 age groups: <5, 5-10 and >11 years and into 2 gender groups. Serum concentrations of fT3, tT3, rT3, fT4 and tT4 were quantified by radioimmunoassay. All blood samples were collected the same day in the morning. None of the animals had received any treatment for 30 days prior to sampling or had any history of disease. Both farms were in close proximity and under similar management. Differences between groups were determined using a one-way ANOVA analysis followed by Fisher's LSD test. P<0.05 was considered significant. Serum TH concentrations were higher in donkeys than in horses (P<0.01). Donkeys <5 years had higher serum rT3, fT4 and tT4 concentrations than donkeys >5 years (P<0.05). Furthermore, older donkeys (>11 years) had lower serum fT3 and tT3 concentrations than younger donkeys' groups (<5 and 5-10 years, P<0.05). TH concentrations were not different between genders (fT3: P = 0.06; tT3: P = 0.08; rT3: P = 0.15; fT4: P = 0.89; and tT4: P = 0.19). Thyroid hormone concentrations are different between healthy adult donkeys and horses. Establishing species-specific TH reference ranges is important when evaluating clinicopathologic data in equids in order to avoid the misdiagnosis of thyroid gland dysfunction. Further studies to elucidate the physiological mechanisms leading to these differences are warranted. © 2012 EVJ Ltd.

Predictive criteria for prostate cancer detection in men with serum PSA concentration of 2.0 to 4.0 ng/mL.

PubMed

Kravchick, Sergey; Peled, Ronit; Dorfman, Dov; Agulansky, Leonid; Ben-Dor, David; Cytron, Shmuel

2005-09-01

To assess the usefulness of measuring testosterone, free testosterone, and the free/total (f/t) prostate-specific antigen (PSA) ratio with the intention of reducing the number of unnecessary biopsies in the patients with PSA values between 2.0 and 4.0 ng/mL. Cancer detection is not rare among patients with PSA values between 2.0 and 4.0 ng/mL. A total of 171 men with serum PSA levels of 2.0 to 4.0 ng/mL were enrolled in this study. The f/t PSA ratio and total and free testosterone levels were quantified. All patients underwent transrectal ultrasound-guided biopsy. The cancer detection rate, clinical and pathologic features of the cancers detected, and the probability of cancer detection in relation to the f/t PSA ratio and total and free testosterone levels were estimated. Two-step statistical analysis was used for descriptive purposes and in the detection of cancer predictors. Statistical significance was set at P < or = 0.05. The mean patient age was 63.3 years. Cancer was detected in 39 (22.8%) of the 171 patients. Only 15.4% of our patients had insignificant cancer. The f/t PSA ratio and total and free testosterone levels were significantly lower in the patients with prostate cancer (19.3%, 13.68 nmol/L, and 28.4 pmol/L, respectively; P < 0.001). The f/t PSA ratio and free testosterone were the strongest predictors of cancer detection (P < 0.001). The results of our study have shown that an important number of cancers could be detected in the PSA range of 2.0 to 4.0 ng/mL. The great majority of cancers detected have the features of medically significant tumors. The combination of the f/t PSA ratio and free testosterone measurements may reveal those patients who require biopsy.

A survey of spatially distributed exterior dust lead loadings in New York City

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caravanos, Jack; Weiss, Arlene L.; School of Medicine, New York University, NY 10016

This work documents ambient lead dust deposition values (lead loading) for the boroughs of New York City in 2003-2004. Currently, no regulatory standards exist for exterior concentrations of lead in settled dust. This is in contrast to the clearance and risk assessment standards that exist for interior residential dust. The reported potential for neurobehavioral toxicity and adverse cognitive development in children due to lead exposure prompts public health concerns about undocumented lead sources. Such sources may include settled dust of outdoor origin. Dust sampling throughout the five boroughs of NYC was done from the top horizontal portion of pedestrian trafficmore » control signals (PTCS) at selected street intersections along main thoroughfares. The data (n=214 samples) show that lead in dust varies within each borough with Brooklyn having the highest median concentration (730{mu}g/ft{sup 2}), followed in descending order by Staten Island (452{mu}g/ft{sup 2}), the Bronx (382{mu}g/ft{sup 2}), Queens (198{mu}g/ft{sup 2}) and finally, Manhattan (175{mu}g/ft{sup 2}). When compared to the HUD/EPA indoor lead in dust standard of 40{mu}g/ft{sup 2}, our data show that this value is exceeded in 86% of the samples taken. An effort was made to determine the source of the lead in the dust atop of the PTCS. The lead in the dust and the yellow signage paint (which contains lead) were compared using isotopic ratio analysis. Results showed that the lead-based paint chip samples from intact signage did not isotopically match the dust wipe samples taken from the same surface. We know that exterior dust containing lead contributes to interior dust lead loading. Therefore, settled leaded dust in the outdoor environment poses a risk for lead exposure to children living in urban areas, namely, areas with elevated childhood blood lead levels and background lead dust levels from a variety of unidentified sources.« less

Investigating the Metallicity–Mixing-length Relation

NASA Astrophysics Data System (ADS)

Viani, Lucas S.; Basu, Sarbani; Joel Ong J., M.; Bonaca, Ana; Chaplin, William J.

2018-05-01

Stellar models typically use the mixing-length approximation as a way to implement convection in a simplified manner. While conventionally the value of the mixing-length parameter, α, used is the solar-calibrated value, many studies have shown that other values of α are needed to properly model stars. This uncertainty in the value of the mixing-length parameter is a major source of error in stellar models and isochrones. Using asteroseismic data, we determine the value of the mixing-length parameter required to properly model a set of about 450 stars ranging in log g, {T}eff}, and [{Fe}/{{H}}]. The relationship between the value of α required and the properties of the star is then investigated. For Eddington atmosphere, non-diffusion models, we find that the value of α can be approximated by a linear model, in the form of α /{α }ȯ =5.426{--}0.101 {log}(g)-1.071 {log}({T}eff}) +0.437([{Fe}/{{H}}]). This process is repeated using a variety of model physics, as well as compared with previous studies and results from 3D convective simulations.

Hydraulic characteristics of, and ground-water flow in, coal-bearing rocks of southwestern Virginia

USGS Publications Warehouse

Harlow, George E.; LeCain, Gary D.

1993-01-01

This report presents the results of a study by the U.S Geological Survey, in cooperation with the Virginia Department of Mines, Minerals, and Energy, Division of Mined Land Reclamation, and the Powell River Project, to describe the hydraulic characteristics of major water-bearing zones in the coal-bearing rocks of southwestern Virginia and to develop a conceptual model of the ground-water-flow system. Aquifer testing in1987 and 1988 of 9-ft intervals in coal-exploration coreholes indicates that transmissivity decreases with increasing depth. Most rock types are permeable to a depth of approximately 100 ft; however, only coal seams are consistently permeable (transmissivity greater than 0.001 ft/d) at depths greater than 200 ft . Constant-head injection testing of rock intervals adjacent to coal seams usually indicated lower values of transmissivity than those values obtained when coal seams were isolated within the test interval; thus, large values of horizontal hydraulic conductivity at depth are associated with coal seams. Potentiometric-head measurements indicate that high topographic areas (ridges) function as recharge areas; water infiltrates through the surface, percolates into regolith, and flows downward and laterally through fractures in the shallow bedrock. Hydraulic conductivity decreases with increasing depth, and ground water flows primarily in the lateral direction along fractures or bedding planes or through coal seams. If vertical hydraulic conductivity is negligible, ground water continues to flow laterally, discharging as springs or seeps on hill slopes. Where vertical hydraulic conductivity is appreciable, groundwater follows a stair step path through the regolith, fractures, bedding planes, and coal seams, discharging to streams and (or) recharging coal seams at depth. Permeable coal seams probably underlie valleys in the region; however, aquifer-test data indicate that the horizontal hydraulic conductivity of coal is a function of depth and probably decreases under ridges because of increased overburden pressures. Ground water beneath valleys that does not discharge to streams probably flows down gradient as underflow beneath the streams. Topographic relief in the area provides large hydraulic-head differences (greater than 300 ft in some instances) for the ground-water-flow system. Transmissivity data from the range of depths tested during this study indicate that most ground-water flow takes place at moderate depths (less than 300 ft) and that little deep regional ground-water flow occurs.

Pharmacokinetic profiles of repaglinide in elderly subjects with type 2 diabetes.

PubMed

Hatorp, V; Huang, W C; Strange, P

1999-04-01

Pharmacokinetic profiles of single- and multiple-dose regimens of repaglinide were evaluated in 12 elderly subjects with type 2 diabetes. On day 1, following a 10-hour fast, subjects received a single 2-mg dose of repaglinide. Starting on day 2 and continuing for 7 days, each subject received a 2-mg dose of repaglinide 15 minutes before each of the three main meals. On day 9, subjects received a single 2-mg dose of repaglinide. Pharmacokinetic profiles, including area under the curve (AUC), log(AUC), maximal concentration (Cmax), log(Cmax), time to maximal concentration (Tmax), and half-life (T(1/2)), were determined at completion of the single- and multiple-dose regimens (days 1 and 9, respectively). Trough repaglinide values were collected on days 2 through 7. The mean log(AUC) values after multiple dosing were significantly higher than the values obtained after a single dose. The mean values for log(Cmax), and Tmax were comparable after each dosing regimen. The T(1/2) of repaglinide after multiple dosing was 1.7 hours. The trough values for repaglinide were low. No hypoglycemic events were reported. The pharmacokinetic profiles of repaglinide after single- and multiple-dose regimens were similar, and repaglinide was well tolerated by elderly subjects with type 2 diabetes.

An ecosystem services approach to the ecological effects of salvage logging: valuation of seed dispersal.

PubMed

Leverkus, Alexandro B; Castro, Jorge

2017-06-01

Forest disturbances diminish ecosystem services and boost disservices. Because post-disturbance management intends to recover the greatest possible value, selling timber often prevails over other considerations. Ecological research has shown diverse effects of salvage logging, yet such research has focused on the biophysical component of post-disturbance ecosystems and lacks the link with human well-being. Here we bridge that gap under the ecosystem services framework by assessing the impact of post-fire management on a non-timber value. By employing the replacement cost method, we calculated the value of the post-fire natural regeneration of Holm oaks in southern Spain under three post-fire management options by considering the cost of planting instead. The value of this ecosystem service in non-intervention areas doubled that of salvage-logged stands due to the preference for standing dead trees by the main seed disperser. Still, most of the value resulted from the resprouting capacity of oaks. The value of this and other ecosystem services should be added to traditional cost/benefit analyses of post-disturbance management. We thus call for a more holistic approach to salvage logging research, one that explicitly links ecological processes with human well-being through ecosystem services, to better inform decision-makers on the outcomes of post-disturbance management. © 2017 by the Ecological Society of America.

[Serum 1, 5-anhydroglucose alcohol: a serum indicator for estimating acute blood sugar fluctuation in patients with fulminant type 1 diabetes].

PubMed

Ge, Jinlian; Xu, Dacheng; Peng, Youfan; Zhang, Mingchen; Cao, Wenyan

2015-11-01

To test the feasibility of using 1,5-anhydroglucose alcohol (1,5-AG) as a diagnostic indicator of fulminant type 1 diabetes (FT1DM). Fifteen patients with newly diagnosed FT1DM and 52 with type 2 diabetes (T2DM) were examined for serum biochemistry, glycosylated hemoglobin (HbAlc), and serum 1, 5-AG level. The patients with FT1DM and T2DM showed significantly different fasting levels of blood glucose (FBG), fructosamine (FMN), creatinine (Cr), urea, HbAlc and serum 1,5-AG (P<0.05). In FT1DM patients, serum 1,5-AG was found to inversely correlate with FBG (r=-0.646, P=0.032) and FMN (r=-0.680, P=0.021), and in T2DM patients, serum 1,5-AG was inversely correlated with FBG (r=-0.407, P=0.001), FMN (r=-0.314, P=0.01) and HbAlc (r=-0.576, P<0.01). Receiver-operating characteristic (ROC) curve analysis showed an area under the curve of serum 1,5-AG of 0.804 with a cutoff value of 67.95, a sensitivity of 82.9% and a specificity of 60% for FT1DM diagnosis. Serum 1, 5-AG can reflect acute blood glucose fluctuation in FT1DM patients and is useful for differential diagnosis of FT1DM when combined with evaluations of the clinical characteristics of the patients and other related indicators.

Simulation analysis of water-level changes in the Navajo sandstone due to changes in the altitude of Lake Powell near Wahweap Bay, Utah and Arizona

USGS Publications Warehouse

Thomas, B.E.

1986-01-01

A two-dimensional, finite difference, digital computer model was used to simulate various concepts of groundwater flow near Wahweap Bay, Lake Powell. The filling of Lake Powell started in March 1963; and by 1983 the lake had risen almost 550 ft. This resulted in a maximum observed water level rise of 395 ft in a well in the Navajo Sandstone 1 mi from the lake. A steady-state model was prepared with subsurface recharge rates of 5,720 acre-ft/yr, 10,440 acre-ft/yr, and 14,820 acre-ft/yr, resulting in a range of hydraulic conductivity of 0.25 to 3.38 ft/da. Comparing measured and simulated water level changes resulted in a range of specific yield of 0.02 to 0.15. Using larger values for hydraulic conductivity in the model area corresponding to the axis of the Wahweap syncline and the Echo monocline was instrumental in attaining a reasonable match for the water level distribution. This supports previous concepts that areas where rocks are structurally deformed more readily transmit groundwater because of the higher degree of fracturing. Using the most likely simulation of the flow system, groundwater storage in the Navajo increased by about 25,000 acre ft/mi of shoreline form 1963-83, but the flow system will require about 400 yr to reach a state of equilibrium. (Author 's abstract)

Synthesis, spectroscopic analyses, chemical reactivity and molecular docking study and anti-tubercular activity of pyrazine and condensed oxadiazole derivatives

NASA Astrophysics Data System (ADS)

Al-Tamimi, Abdul-Malek S.; Mary, Y. Sheena; Miniyar, Pankaj B.; Al-Wahaibi, Lamya H.; El-Emam, Ali A.; Armaković, Stevan; Armaković, Sanja J.

2018-07-01

The FT-IR spectral analysis and theoretical calculations of the wavenumbers of three oxadiazole derivatives, 2-(5-(2-chlorophenyl)-1,3,4-oxadiazol-2-yl)pyrazine (ORTHOPHPZ), 2-(5-(3-chlorophenyl)-1,3,4-oxadiazol-2-yl)pyrazine (METAPHPZ) and 2-(5-(4-chlorophenyl)-1,3,4-oxadiazol-2-yl)pyrazine (PARAPHPZ) were reported in the present work. The theoretically predicted values of polarizability give the nonlinear behaviour of the compounds. The frontier molecular orbital analysis show the chemical stability of the title compounds and the NBO analysis gives the interactions in the molecular systems. Understanding of reactivity of newly synthetiszed oxadiazole derivatives in this study has been achieved thanks to combination of density functional theory (DFT) calculations, molecular dynamics (MD) simulations and molecular docking procedures. New oxadiazole derivatives have also been characterized experimentally through FT-IR and NMR approaches, thanks to which detailed structural properties have been understood. Both global and local reactivity properties have been investigated by calculations of quantum molecular descriptors such as molecular electrostatic potential (MEP), local average ionization energy (ALIE), Fukui functions, bond dissociation energies for hydrogen abstraction (H-BDE), radial distribution functions and binding energies of ligand against selected protein. The first hyperpolarizabilities of ORTHOPHPZ, METAPHPZ and PARAPHPZ are respectively, 84.62, 94.71 and 184.10 times that of urea. The docked ligands form stable complexes with the receptor 1-phosphatidylinositol phosphodiesterase and the results suggest that these compounds can be developed as new anti-cancer drugs. The anti-TB activity of PM series against M. tuberculosis H37RV strain was performed by Middlebrooke 7H-9 method. The compounds, ORTHOPHPZ, METAPHPZ and PARAPHPZ were moderately active between 25 and 50 μg/ml concentration as compared with the standard anti-TB agents and the -log MIC activity was found in the range of 1.011-1.274 as compared with isoniazid (INH) (1.137) and pyrazinamide (PZA) (1.115) standard anti-TB agents.

Determination of 1-octanol-air partition coefficient using gaseous diffusion in the air boundary layer.

PubMed

Ha, Yeonjeong; Kwon, Jung-Hwan

2010-04-15

Exact determination of the partition coefficient between 1-octanol and air (K(OA)) is very important because it is a key descriptor for describing the thermodynamic partitioning between the air and organic phases. In spite of its importance, the number and quality of experimental K(OA) values for hydrophobic organic chemicals are limited because of experimental difficulties. Thus, to measure K(OA) values, a high-throughput method was developed that used liquid-phase extraction with 1-octanol drop at the tip of a microsyringe needle. The concentration in the headspace surrounding the 1 muL octanol drop was equilibrated with liquid octanol containing polycyclic aromatic hydrocarbons (PAHs). The change in concentrations of PAHs in the octanol drop was measured to obtain mass transfer rate constants, and these rate constants were then converted into K(OA) values using a film diffusion model. Thirteen polycyclic aromatic hydrocarbons with log K(OA) between 5 and 12 were chosen for the proof of the principle. Experimental determination of log K(OA) was accomplished in 30 h for PAHs with their log K(OA) less than 11. The measured log K(OA) values were very close to those obtained by various experimental and estimation methods in the literature, suggesting that this new method can provide a fast and easy determination of log K(OA) values for many chemicals of environmental interests. In addition, the applicability of the method can be extended to determine Henry's law constant for compounds with low vapor pressure and to estimate gaseous transfer rate of semivolatile compounds for environmental fate modeling.

Nuclear Data Sheets for A=164

NASA Astrophysics Data System (ADS)

Singh, Balraj; Chen, Jun

2018-01-01

Experimental nuclear structure data for the known A=164 isobaric nuclides (Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Hf, Ta, W, Re, Os, Ir) have been evaluated, and presented together with Adopted properties of level energies, and associated γ rays. The decay data for these nuclides have also been evaluated, providing Adopted values of γ and β radiations, and log ft values. No excited states are known in 164Eu, 164Tb, and 164Ir. Information for 164Gd, 164Re and 164Os is limited due to insufficient experimental data. For radioactive nuclides, decay schemes of 164Sm, 164Gd and 164Re are not known, and those of 164W, 164Tb, 164Lu, 164Hf, 164Ta and 164W are incomplete. The decay schemes of 164Ho and the two activities of 164Tm seem fairly complete. The decay scheme of 164Yb presents a major problem that the Q(ε) value of 887 keV 29 recommended in 2017Wa10 is in disagreement with the population of levels at 928, 952 and 1060 keV in the daughter nucleus. This decay scheme, which so far has been mainly reported in a secondary reference (1982AdZZ) needs further investigation. Also the masses of 164Yb and 164Tm need either new measurements or a re-evaluation to resolve discrepancy of about 220 keV in the Q value of 164Yb decay to 164Tm. The reactions and decays for which no new experimental information has become available since the 2001 update have undergone revisions to incorporate conversion coefficients from BrIcc code, and evaluated Q values from 2017Wa10, but the essential content of such datasets may have remained the same as in previous evaluations. In this respect the present work greatly benefited from all the previous NDS evaluations (2001Si27,1992Sh07, 1986Sh03,1974Bu30), but at the same time data presented herein supersede all the previous published evaluations.

Possible role of serum testosterone, gonadotropins and prolactin in patients with premature ejaculation.

PubMed

Abu El-Hamd, M; Farah, A

2018-02-01

Premature ejaculation (PE) is the most common male sexual dysfunction. This study aimed to investigate the role of serum testosterone, gonadotropins and prolactin in patients with PE. In a prospective a case-controlled study, it was conducted on 90 male patients with PE and 90 male healthy participants as controls. Patients were evaluated by Premature Ejaculation Diagnostic Tool (PEDT) and intravaginal ejaculatory latency time (IELT). Patients with mean IELT values ≤60 s and PEDT total scores ≥11 were considered to have PE. Serum levels of total testosterone (TT), free testosterone (FT), follicle-stimulating hormone (FSH), luteinising hormone (LH) and prolactin (PL) were investigated in patients with PE and controls. There was no statistically significant difference between patients with PE and controls regarding the serum levels of TT, FT, FSH, LH and PL (p value ˃.05). There was no significant correlation between the sex hormones levels (TT, FT, FSH, LH and PL) and (age, body mass index (BMI), IELTS and total PEDT scores of the patients; p value ˃.05). This study concluded that there was no disturbance in serum levels of testosterone, gonadotropins and prolactin in patients with PE and controls. These hormones could not relate to pathogenesis of PE. © 2017 Blackwell Verlag GmbH.

Prediction of gas/particle partitioning of polybrominated diphenyl ethers (PBDEs) in global air: a theoretical study

NASA Astrophysics Data System (ADS)

Li, Y.-F.; Ma, W.-L.; Yang, M.

2014-09-01

Gas/particle (G / P) partitioning for most semivolatile organic compounds (SVOCs) is an important process that primarily governs their atmospheric fate, long-range atmospheric transport potential, and their routs to enter human body. All previous studies on this issue have been hypothetically derived from equilibrium conditions, the results of which do not predict results from monitoring studies well in most cases. In this study, a steady-state model instead of an equilibrium-state model for the investigation of the G / P partitioning behavior for polybrominated diphenyl ethers (PBDEs) was established, and an equation for calculating the partition coefficients under steady state (KPS) for PBDE congeners (log KPS = log KPE + logα) was developed, in which an equilibrium term (log KPE = log KOA + logfOM -11.91, where fOM is organic matter content of the particles) and a nonequilibrium term (logα, mainly caused by dry and wet depositions of particles), both being functions of log KOA (octanol-air partition coefficient), are included, and the equilibrium is a special case of steady state when the nonequilibrium term equals to zero. A criterion to classify the equilibrium and nonequilibrium status for PBDEs was also established using two threshold values of log KOA, log KOA1 and log KOA2, which divide the range of log KOA into 3 domains: equilibrium, nonequilibrium, and maximum partition domains; and accordingly, two threshold values of temperature t, tTH1 when log KOA = log KOA1 and tTH2 when log KOA = log KOA2, were identified, which divide the range of temperature also into the same 3 domains for each BDE congener. We predicted the existence of the maximum partition domain (the values of log KPS reach a maximum constant of -1.53) that every PBDE congener can reach when log KOA ≥ log KOA2, or t ≤ tTH2. The novel equation developed in this study was applied to predict the G / P partition coefficients of PBDEs for the published monitoring data worldwide, including Asia, Europe, North America, and the Arctic, and the results matched well with all the monitoring data, except those obtained at e-waste sites due to the unpredictable PBDE emissions at these sites. This study provided evidence that, the new developed steady-state-based equation is superior to the equilibrium-state-based equation that has been used in describing the G / P partitioning behavior in decades. We suggest that, the investigation on G / P partitioning behavior for PBDEs should be based on steady state, not equilibrium state, and equilibrium is just a special case of steady state when nonequilibrium factors can be ignored. We also believe that our new equation provides a useful tool for environmental scientists in both monitoring and modeling research on G / P partitioning for PBDEs and can be extended to predict G / P partitioning behavior for other SVOCs as well.

Molecular structure, vibrational spectra, AIM, HOMO-LUMO, NBO, UV, first order hyperpolarizability, analysis of 3-thiophenecarboxylic acid monomer and dimer by Hartree-Fock and density functional theory

NASA Astrophysics Data System (ADS)

Issaoui, Noureddine; Ghalla, Houcine; Muthu, S.; Flakus, H. T.; Oujia, Brahim

2015-02-01

In this work, the molecular structure, harmonic vibrational frequencies, UV, NBO and AIM of 3-thiophenecarboxilic acid (abbreviated as 3-TCA) monomer and dimer has been investigated. The FT-IR and FT-Raman spectra were recorded. The ground-state molecular geometry and vibrational frequencies have been calculated by using the Hartree-Fock (HF) and density functional theory (DFT)/B3LYP methods and 6-311++G(d,p) as a basis set. The fundamental vibrations were assigned on the basis of the total energy distribution (TED) of the vibrational modes, calculated with VEDA program. Comparison of the observed fundamental vibrational frequencies of 3-TCA with calculated results by HF and DFT methods indicates that B3LYP is better to HF method for molecular vibrational problems. The difference between the observed and scaled wavenumber values is very small. The theoretically predicted FT-IR and FT-Raman spectra of the title compound have been constructed. A study on the Mulliken atomic charges, the electronic properties were performed by time-dependent DFT (TD-DFT) approach, frontier molecular orbitals (HOMO-LUMO), molecular electrostatic potential (MEP) and thermodynamic properties have been performed. The electric dipole moment (μ) and the first hyperpolarizability (β) values of the investigated molecule have been also computed.

Molecular structure, vibrational spectra, AIM, HOMO-LUMO, NBO, UV, first order hyperpolarizability, analysis of 3-thiophenecarboxylic acid monomer and dimer by Hartree-Fock and density functional theory.

PubMed

Issaoui, Noureddine; Ghalla, Houcine; Muthu, S; Flakus, H T; Oujia, Brahim

2015-02-05

In this work, the molecular structure, harmonic vibrational frequencies, UV, NBO and AIM of 3-thiophenecarboxilic acid (abbreviated as 3-TCA) monomer and dimer has been investigated. The FT-IR and FT-Raman spectra were recorded. The ground-state molecular geometry and vibrational frequencies have been calculated by using the Hartree-Fock (HF) and density functional theory (DFT)/B3LYP methods and 6-311++G(d,p) as a basis set. The fundamental vibrations were assigned on the basis of the total energy distribution (TED) of the vibrational modes, calculated with VEDA program. Comparison of the observed fundamental vibrational frequencies of 3-TCA with calculated results by HF and DFT methods indicates that B3LYP is better to HF method for molecular vibrational problems. The difference between the observed and scaled wavenumber values is very small. The theoretically predicted FT-IR and FT-Raman spectra of the title compound have been constructed. A study on the Mulliken atomic charges, the electronic properties were performed by time-dependent DFT (TD-DFT) approach, frontier molecular orbitals (HOMO-LUMO), molecular electrostatic potential (MEP) and thermodynamic properties have been performed. The electric dipole moment (μ) and the first hyperpolarizability (β) values of the investigated molecule have been also computed. Copyright © 2014 Elsevier B.V. All rights reserved.

Borehole geophysical investigation of a formerly used defense site, Machiasport, Maine, 2003-2006

USGS Publications Warehouse

Johnson, Carole D.; Mondazzi, Remo A.; Joesten, Peter K.

2011-01-01

The U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, collected borehole geophysical logs in 18 boreholes and interpreted the data along with logs from 19 additional boreholes as part of an ongoing, collaborative investigation at three environmental restoration sites in Machiasport, Maine. These sites, located on hilltops overlooking the seacoast, formerly were used for military defense. At each of the sites, chlorinated solvents, used as part of defense-site operations, have contaminated the fractured-rock aquifer. Borehole geophysical techniques and hydraulic methods were used to characterize bedrock lithology, fractures, and hydraulic properties. In addition, each geophysical method was evaluated for effectiveness for site characterization and for potential application for further aquifer characterization and (or) evaluation of remediation efforts. Results of borehole geophysical logging indicate the subsurface is highly fractured, metavolcanic, intrusive, metasedimentary bedrock. Selected geophysical logs were cross-plotted to assess correlations between rock properties. These plots included combinations of gamma, acoustic reflectivity, electromagnetic induction conductivity, normal resistivity, and single-point resistance. The combined use of acoustic televiewer (ATV) imaging and natural gamma logs proved to be effective for delineating rock types. Each of the rock units in the study area could be mapped in the boreholes, on the basis of the gamma and ATV reflectivity signatures. The gamma and mean ATV reflectivity data were used along with the other geophysical logs for an integrated interpretation, yielding a determination of quartz monzonite, rhyolite, metasedimentary units, or diabase/gabbro rock types. The interpretation of rock types on the basis of the geophysical logs compared well to drilling logs and geologic mapping. These results may be helpful for refining the geologic framework at depth. A stereoplot of all fractures intersecting the boreholes indicates numerous fractures, a high proportion of steeply dipping fractures, and considerable variation in fracture orientation. Low-dip-angle fractures associated with unloading and exfoliation are also present, especially at a depth of less than 100 feet below the top of casing. These sub-horizontal fractures help to connect the steeply dipping fractures, making this a highly connected fracture network. The high variability in the fracture orientations also increases the connectivity of the fracture network. A preliminary comparison of all fracture data from all the boreholes suggests fracturing decreases with depth. Because all the boreholes were not drilled to the same depth, however, there is a clear sampling bias. Hence, the deepest boreholes are analyzed separately for fracture density. For the deepest boreholes in the study, the intensity of fracturing does not decline significantly with depth. It is possible the fractures observed in these boreholes become progressively tighter or closed with depth, but this is difficult to verify with the borehole methods used in this investigation. The fact that there are more sealed fractures at depth (observed in optical televiewer logs in some of the boreholes) may indicate less opening of the sealed fractures, less water moving through the rock, and less weathering of the fracture infilling minerals. Although the fracture orientation remained fairly constant with depth, differences in the fracture patterns for the three restoration sites indicate the orientation of fractures varies across the study area. The fractures in boreholes on Miller Mountain predominantly strike northwest-southeast, and to a lesser degree they strike northeast. The fractures on or near the summit of Howard Mountain strike predominantly east-west and dip north and south, and the fractures near the Transmitter Site strike northeast-southwest and dip northwest and southeast. The fracture populations for the boreholes on or near the summit of Howard Mountain show more variation than at the other two sites. This variation may be related to the proximity of the fault, which is northeast of the summit of Howard Mountain. In a side-by-side comparison of stereoplots from selected boreholes, there was no clear correspondence between fracture orientation and proximity to the fault. There is, however, a difference in the total populations of fractures for the boreholes on or near the summit of Howard Mountain and the boreholes near the Transmitter Site. Further to the southwest and further away from the fault, the fractures at the Transmitter Site predominantly strike northeast-southwest and northwest-southeast.Heat-pulse flowmeter (HPFM) logging was used to identify transmissive fractures and to estimate the hydraulic properties along the boreholes. Ambient downflow was measured in 13 boreholes and ambient upflow was measured in 9 boreholes. In nine other bedrock boreholes, the HPFM did not detect measurable vertical flow. The observed direction of vertical flow in the boreholes generally was consistent with the conceptual flow model of downward movement in recharge locations and upward flow in discharge locations or at breaks in the slope of land surface. Under low-rate pumping or injection rates [0.25 to 1 gallon per minute (gal/min)], one to three inflow zones were identified in each borehole. Two limitations of HPFM methods are (1) the HPFM can only identify zones within 1.5 to 2 orders of magnitude of the most transmissive zone in each borehole, and (2) the HPFM cannot detect flow rates less than 0.010 + or - 0.005 gal/min, which corresponds to a transmissivity of about 1 foot squared per day (ft2/d). Consequently, the HPFM is considered an effective tool for identifying the most transmissive fractures in a borehole, down to its detection level. Transmissivities below that cut-off must be measured with another method, such as packer testing or fluid-replacement logging. Where sufficient water-level and flowmeter data were available, HPFM results were numerically modeled. For each borehole model, the fracture location and measured flow rates were specified, and the head and transmissivity of each fracture zone were adjusted until a model fit was achieved with the interpreted ambient and stressed flow profiles. The transmissivities calculated by this method are similar to the results of an open-hole slug test; with the added information from the flowmeter, however, the head and transmissivity of discrete zones also can be determined. The discrete-interval transmissivities ranged from 0.16 to 330 ft2/d. The flowmeter-derived open-hole transmissivity, which is the combined total of each of the transmissive zones, ranged from 1 to 511 ft2/d. The whole-well open-hole transmissivity values determined with HPFM methods were compared to the results of open-hole hydraulic tests. Despite the fact that the flowmeter-derived transmissivities consistently were lower than the estimates derived from open-hole hydraulic tests alone, the correlation was very strong (with a coefficient of determination, R2, of 0.9866), indicating the HPFM method provides a reasonable estimate of transmissivities for the most transmissive fractures in the borehole. Geologic framework, fracture characterization, and estimates of hydraulic properties were interpreted together to characterize the fracture network. The data and interpretation presented in this report should provide information useful for site investigators as the conceptual site groundwater flow model is refined. Collectively, the results and the conceptual site model are important for evaluating remediation options and planning or implementing the design of a well field and borehole completions that will be adequate for monitoring flow, remediation efforts, groundwater levels, and (or) water quality. Similar kinds of borehole geophysical logging (specifically the borehole imaging, gamma, fluid logs, and HPFM) should be conducted in any newly installed boreholes and integrated with interpretations of any nearby boreholes. If boreholes are installed close to existing or other new boreholes, cross-hole flowmeter surveys may be appropriate and may help characterize the aquifer properties and connections between the boreholes.

Comparison of pitot traverses taken at varying distances downstream of obstructions.

PubMed

Guffey, S E; Booth, D W

1999-01-01

This study determined the deviations between pitot traverses taken under "ideal" conditions--at least seven duct diameter's lengths (i.e., distance = 7D) from obstructions, elbows, junction fittings, and other disturbances to flows--with those taken downstream from commonplace disturbances. Two perpendicular 10-point, log-linear velocity pressure traverses were taken at various distances downstream of tested upstream conditions. Upstream conditions included a plain duct opening, a junction fitting, a single 90 degrees elbow, and two elbows rotated 90 degrees from each other into two orthogonal planes. Airflows determined from those values were compared with the values measured more than 40D downstream of the same obstructions under ideal conditions. The ideal measurements were taken on three traverse diameters in the same plane separated by 120 degrees in honed drawn-over-mandrel tubing. In all cases the pitot tubes were held in place by devices that effectively eliminated alignment errors and insertion depth errors. Duct velocities ranged from 1500 to 4500 ft/min. Results were surprisingly good if one employed two perpendicular traverses. When the averages of two perpendicular traverses was taken, deviations from ideal value were 6% or less even for traverses taken as close as 2D distance from the upstream disturbances. At 3D distance, deviations seldom exceeded 5%. With single diameter traverses, errors seldom exceeded 5% at 6D or more downstream from the disturbance. Interestingly, percentage deviations were about the same at high and low velocities. This study demonstrated that two perpendicular pitot traverses can be taken as close as 3D from these disturbances with acceptable (< or = 5%) deviations from measurements taken under ideal conditions.

Hydrogeologic framework and characterization of the Truxton Aquifer on the Hualapai Reservation, Mohave County, Arizona

USGS Publications Warehouse

Bills, Donald J.; Macy, Jamie P.

2016-12-30

The U.S. Geological Survey, in cooperation with the Bureau of Reclamation, developed this study to determine an estimate of groundwater in storage in the Truxton aquifer on the Hualapai Reservation in northwestern Arizona. For this study, the Truxton aquifer is defined as the unconfined, saturated groundwater in the unconsolidated to semiconsolidated older and younger basin-fill deposits of the Truxton basin overlying bedrock. The physical characteristics of the Truxton aquifer have not been well characterized in the past. In particular, the depth to impermeable granite bedrock and thickness of the basin are known in only a few locations where water wells have penetrated into the granite. Increasing water demands on the Truxton aquifer by both tribal and nontribal water users have led to concern about the long-term sustainability of this water resource. The Hualapai Tribe currently projects an increase of their water needs from about 300 acre-feet (acre-ft) per year to about 780 acre-ft per year by 2050 to support the community of Peach Springs, Arizona, and the southern part of the reservation. This study aimed to quantitatively develop better knowledge of aquifer characteristics, including aquifer storage and capacity, using (1) surface resistivity data collected along transects and (2) analysis of existing geologic, borehole, precipitation, water use, and water-level data.The surface resistivity surveys indicated that the depth to granite along the survey lines varied from less than 100 feet (ft) to more than 1,300 ft below land surface on the Hualapai Reservation. The top of the granite bedrock is consistent with the erosional character of the Truxton basin and exhibits deep paleochannels filled with basin-fill deposits consistent with the results of surface resistivity surveys and borehole logs from wells. The estimated average saturated thickness of the Truxton aquifer on the Hualapai Reservation is about 330 ft (with an estimated range of 260 to 390 ft), based on both resistivity results and the depth to water in wells. The saturated thickness might be greater in parts of the Truxton aquifer where paleochannels are incised into the granite underlying the basin-fill sediments. The estimated groundwater storage of the Truxton aquifer on the Hualapai Reservation ranges from 420,000 to 940,000 acre-ft and does not include groundwater storage in the aquifer outside the Hualapai Reservation boundary. In addition, the calculation of total storage in the Truxton aquifer does not determine nor indicate the availability and sustainability of that groundwater as a long-term resource. These results compared well with studies done on alluvial-basin aquifers in areas adjacent to this study. The part of the Truxton aquifer on the Hualapai Reservation represents about 20 percent of the entire aquifer.

A new solar carbon abundance based on non-LTE CN molecular spectra

NASA Technical Reports Server (NTRS)

Mount, G. H.; Linsky, J. L.

1975-01-01

A detailed non-LTE analysis of solar CN spectra strongly suggest a revised carbon abundance for the sun. We recommend a value of log carbon abundance = 8.35 plus or minus 0.15 which is significantly lower than the presently accepted value of log carbon abundance = 8.55. This revision may have important consequences in astrophysics.

Comparison of lumber values for Grade-3 hardwood logs from thinnings and mature stands

Treesearch

David M. Emanuel

1983-01-01

The value per M bf (thousand board feet) of the lumber sawed from Grade-3 logs, 8 to 11 inches in diameter, from thinnings was compared with that from a harvest of mature-stand cut. The species tested were red oak (Quercus rubra L.), yellow-poplar (Liriodendron tulipifera L.), and hard maple (Acer saccharum Marsh...

Meta-Analysis of the Reduction of Norovirus and Male-Specific Coliphage Concentrations in Wastewater Treatment Plants.

PubMed

Pouillot, Régis; Van Doren, Jane M; Woods, Jacquelina; Plante, Daniel; Smith, Mark; Goblick, Gregory; Roberts, Christopher; Locas, Annie; Hajen, Walter; Stobo, Jeffrey; White, John; Holtzman, Jennifer; Buenaventura, Enrico; Burkhardt, William; Catford, Angela; Edwards, Robyn; DePaola, Angelo; Calci, Kevin R

2015-07-01

Human norovirus (NoV) is the leading cause of foodborne illness in the United States and Canada. Wastewater treatment plant (WWTP) effluents impacting bivalve mollusk-growing areas are potential sources of NoV contamination. We have developed a meta-analysis that evaluates WWTP influent concentrations and log10 reductions of NoV genotype I (NoV GI; in numbers of genome copies per liter [gc/liter]), NoV genotype II (NoV GII; in gc/liter), and male-specific coliphage (MSC; in number of PFU per liter), a proposed viral surrogate for NoV. The meta-analysis included relevant data (2,943 measurements) reported in the scientific literature through September 2013 and previously unpublished surveillance data from the United States and Canada. Model results indicated that the mean WWTP influent concentration of NoV GII (3.9 log10 gc/liter; 95% credible interval [CI], 3.5, 4.3 log10 gc/liter) is larger than the value for NoV GI (1.5 log10 gc/liter; 95% CI, 0.4, 2.4 log10 gc/liter), with large variations occurring from one WWTP to another. For WWTPs with mechanical systems and chlorine disinfection, mean log10 reductions were -2.4 log10 gc/liter (95% CI, -3.9, -1.1 log10 gc/liter) for NoV GI, -2.7 log10 gc/liter (95% CI, -3.6, -1.9 log10 gc/liter) for NoV GII, and -2.9 log10 PFU per liter (95% CI, -3.4, -2.4 log10 PFU per liter) for MSCs. Comparable values for WWTPs with lagoon systems and chlorine disinfection were -1.4 log10 gc/liter (95% CI, -3.3, 0.5 log10 gc/liter) for NoV GI, -1.7 log10 gc/liter (95% CI, -3.1, -0.3 log10 gc/liter) for NoV GII, and -3.6 log10 PFU per liter (95% CI, -4.8, -2.4 PFU per liter) for MSCs. Within WWTPs, correlations exist between mean NoV GI and NoV GII influent concentrations and between the mean log10 reduction in NoV GII and the mean log10 reduction in MSCs. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Distribution of Hydroxyl Groups in Kukersite Shale Oil: Quantitative Determination Using Fourier Transform Infrared (FT-IR) Spectroscopy.

PubMed

Baird, Zachariah Steven; Oja, Vahur; Järvik, Oliver

2015-05-01

This article describes the use of Fourier transform infrared (FT-IR) spectroscopy to quantitatively measure the hydroxyl concentrations among narrow boiling shale oil cuts. Shale oil samples were from an industrial solid heat carrier retort. Reference values were measured by titration and were used to create a partial least squares regression model from FT-IR data. The model had a root mean squared error (RMSE) of 0.44 wt% OH. This method was then used to study the distribution of hydroxyl groups among more than 100 shale oil cuts, which showed that hydroxyl content increased with the average boiling point of the cut up to about 350 °C and then leveled off and decreased.

Prediction of octanol-air partition coefficients for polychlorinated biphenyls (PCBs) using 3D-QSAR models.

PubMed

Chen, Ying; Cai, Xiaoyu; Jiang, Long; Li, Yu

2016-02-01

Based on the experimental data of octanol-air partition coefficients (KOA) for 19 polychlorinated biphenyl (PCB) congeners, two types of QSAR methods, comparative molecular field analysis (CoMFA) and comparative molecular similarity indices analysis (CoMSIA), are used to establish 3D-QSAR models using the structural parameters as independent variables and using logKOA values as the dependent variable with the Sybyl software to predict the KOA values of the remaining 190 PCB congeners. The whole data set (19 compounds) was divided into a training set (15 compounds) for model generation and a test set (4 compounds) for model validation. As a result, the cross-validation correlation coefficient (q(2)) obtained by the CoMFA and CoMSIA models (shuffled 12 times) was in the range of 0.825-0.969 (>0.5), the correlation coefficient (r(2)) obtained was in the range of 0.957-1.000 (>0.9), and the SEP (standard error of prediction) of test set was within the range of 0.070-0.617, indicating that the models were robust and predictive. Randomly selected from a set of models, CoMFA analysis revealed that the corresponding percentages of the variance explained by steric and electrostatic fields were 23.9% and 76.1%, respectively, while CoMSIA analysis by steric, electrostatic and hydrophobic fields were 0.6%, 92.6%, and 6.8%, respectively. The electrostatic field was determined as a primary factor governing the logKOA. The correlation analysis of the relationship between the number of Cl atoms and the average logKOA values of PCBs indicated that logKOA values gradually increased as the number of Cl atoms increased. Simultaneously, related studies on PCB detection in the Arctic and Antarctic areas revealed that higher logKOA values indicate a stronger PCB migration ability. From CoMFA and CoMSIA contour maps, logKOA decreased when substituents possessed electropositive groups at the 2-, 3-, 3'-, 5- and 6- positions, which could reduce the PCB migration ability. These results are expected to be beneficial in predicting logKOA values of PCB homologues and derivatives and in providing a theoretical foundation for further elucidation of the global migration behaviour of PCBs. Copyright © 2015 Elsevier Inc. All rights reserved.

Development of gestation-specific reference intervals for thyroid hormones in normal pregnant Northeast Chinese women: What is the rational division of gestation stages for establishing reference intervals for pregnancy women?

PubMed

Liu, Jianhua; Yu, Xiaojun; Xia, Meng; Cai, Hong; Cheng, Guixue; Wu, Lina; Li, Qiang; Zhang, Ying; Sheng, Mengyuan; Liu, Yong; Qin, Xiaosong

2017-04-01

A laboratory- and region-specific trimester-related reference interval for thyroid hormone assessment of pregnant women was recommended. Whether the division by trimester is suitable requires verification. Here, we tried to establish appropriate reference intervals of thyroid-related hormones and antibodies for normal pregnant women in Northeast China. A total of 947 pregnant women who underwent routine prenatal care were grouped via two methods. The first method entailed division by trimester: stages T1, T2, and T3. The second method entailed dividing T1, T2, and T3 stages into two stages each: T1-1, T1-2, T2-1, T2-2, T3-1, and T3-2. Serum levels of TSH, FT3, FT4, Anti-TPO, and Anti-TG were measured by three detection systems. No significant differences were found in TSH values between T1-1 group and the non-pregnant women group. However, the TSH value of the T1-1 group was significantly higher than that of T1-2 group (P<0.05). The TSH values in stage T3-2 increased significantly compared to those in stage T3-1 measured by three different assays (P<0.05). FT4 and FT3 values decreased significantly in the T2-1 and T2-2 stages compared to the previous stage (P<0.05). The serum levels of Anti-TPO and Anti-TG were not having significant differences between the six stages. The diagnosis and treatment of thyroid dysfunction during pregnancy should base on pregnancy- and method-specific reference intervals. More detailed staging is required to assess the thyroid function of pregnant women before 20 gestational weeks. Copyright © 2016 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

Thermal maturity and organic composition of Pennsylvanian coals and carbonaceous shales, north-central Texas: Implications for coalbed gas potential

USGS Publications Warehouse

Hackley, P.C.; Guevara, E.H.; Hentz, T.F.; Hook, R.W.

2009-01-01

Thermal maturity was determined for about 120 core, cuttings, and outcrop samples to investigate the potential for coalbed gas resources in Pennsylvanian strata of north-central Texas. Shallow (< 600??m; 2000??ft) coal and carbonaceous shale cuttings samples from the Middle-Upper Pennsylvanian Strawn, Canyon, and Cisco Groups in Archer and Young Counties on the Eastern Shelf of the Midland basin (northwest and downdip from the outcrop) yielded mean random vitrinite reflectance (Ro) values between about 0.4 and 0.8%. This range of Ro values indicates rank from subbituminous C to high volatile A bituminous in the shallow subsurface, which may be sufficient for early thermogenic gas generation. Near-surface (< 100??m; 300??ft) core and outcrop samples of coal from areas of historical underground coal mining in the region yielded similar Ro values of 0.5 to 0.8%. Carbonaceous shale core samples of Lower Pennsylvanian strata (lower Atoka Group) from two deeper wells (samples from ~ 1650??m; 5400??ft) in Jack and western Wise Counties in the western part of the Fort Worth basin yielded higher Ro values of about 1.0%. Pyrolysis and petrographic data for the lower Atoka samples indicate mixed Type II/Type III organic matter, suggesting generated hydrocarbons may be both gas- and oil-prone. In all other samples, organic material is dominated by Type III organic matter (vitrinite), indicating that generated hydrocarbons should be gas-prone. Individual coal beds are thin at outcrop (< 1??m; 3.3??ft), laterally discontinuous, and moderately high in ash yield and sulfur content. A possible analog for coalbed gas potential in the Pennsylvanian section of north-central Texas occurs on the northeast Oklahoma shelf and in the Cherokee basin of southeastern Kansas, where contemporaneous gas-producing coal beds are similar in thickness, quality, and rank.

Hardwood sawyer trainer

Treesearch

Luis G. Occeña; Eknarin Santitrakul; Daniel L. Schmoldt

2000-01-01

It is well understood by now that the initial breakdown of hardwood logs into lumber has a tremendous impact on the total lumber value and conversion efficiency. The focus of this research project is the development of a computer-aided sawing trainer tool for the primary breakdown of hardwood logs. Maximum lumber recovery is dependent on the proper log orientation as...

Sitka spruce and western hemlock beach logs in southeast Alaska: suitability for lumber, pulp, and energy.

Treesearch

Susan Ernst; Marlin E. Plank; Donald J. Fahey

1986-01-01

The suitability of western hemlock (Tsuga heterophylla (Raf.) Sarg.) and Sitka spruce (Picea sitchensis (Bong.) Carr.) beach logs in southeast Alaska for lumber, pulp, and energy was determined. Logs were sawn at a cant mill in southeast Alaska and at a dimension mill in northern Washington. Volume and value recovery was...

Primary detection of hardwood log defects using laser surface scanning

Treesearch

Ed Thomas; Liya Thomas; Lamine Mili; Roger Ehrich; A. Lynn Abbott; Clifford Shaffer; Clifford Shaffer

2003-01-01

The use of laser technology to scan hardwood log surfaces for defects holds great promise for improving processing efficiency and the value and volume of lumber produced. External and internal defect detection to optimize hardwood log and lumber processing is one of the top four technological needs in the nation's hardwood industry. The location, type, and...

Is Log Ratio a Good Value for Measuring Return in Stock Investments?

NASA Astrophysics Data System (ADS)

Ultsch, Alfred

Measuring the rate of return is an important issue for theory and practice of investments in the stock market. A common measure for rate of return is the logarithm of the ratio of successive prices (LogRatio). In this paper it is shown that LogRatio as well as arithmetic return rate (Ratio) have several disadvantages. As an alternative relative differences (RelDiff) are proposed to measure return. The stability against numerical and rounding errors of RelDiff is much better than for LogRatios and Ratio). RelDiff values are identical to LogRatios and Return for small absolutes. The usage of RelDiff maps returns to a finite range. For most subsequent analyses this is a big advantage. The usefulness of the approach is demonstrated on daily return rates of a large set of actual stocks. It is shown that returns can be modeled with a very simple mixture of distributions in great precision using Relative differences.

Joint inversion of acoustic and resistivity data for the estimation of gas hydrate concentration

USGS Publications Warehouse

Lee, Myung W.

2002-01-01

Downhole log measurements, such as acoustic or electrical resistivity logs, are frequently used to estimate in situ gas hydrate concentrations in the pore space of sedimentary rocks. Usually the gas hydrate concentration is estimated separately based on each log measurement. However, measurements are related to each other through the gas hydrate concentration, so the gas hydrate concentrations can be estimated by jointly inverting available logs. Because the magnitude of slowness of acoustic and resistivity values differs by more than an order of magnitude, a least-squares method, weighted by the inverse of the observed values, is attempted. Estimating the resistivity of connate water and gas hydrate concentration simultaneously is problematic, because the resistivity of connate water is independent of acoustics. In order to overcome this problem, a coupling constant is introduced in the Jacobian matrix. In the use of different logs to estimate gas hydrate concentration, a joint inversion of different measurements is preferred to the averaging of each inversion result.

Log-amplitude statistics for Beck-Cohen superstatistics

NASA Astrophysics Data System (ADS)

Kiyono, Ken; Konno, Hidetoshi

2013-05-01

As a possible generalization of Beck-Cohen superstatistical processes, we study non-Gaussian processes with temporal heterogeneity of local variance. To characterize the variance heterogeneity, we define log-amplitude cumulants and log-amplitude autocovariance and derive closed-form expressions of the log-amplitude cumulants for χ2, inverse χ2, and log-normal superstatistical distributions. Furthermore, we show that χ2 and inverse χ2 superstatistics with degree 2 are closely related to an extreme value distribution, called the Gumbel distribution. In these cases, the corresponding superstatistical distributions result in the q-Gaussian distribution with q=5/3 and the bilateral exponential distribution, respectively. Thus, our finding provides a hypothesis that the asymptotic appearance of these two special distributions may be explained by a link with the asymptotic limit distributions involving extreme values. In addition, as an application of our approach, we demonstrated that non-Gaussian fluctuations observed in a stock index futures market can be well approximated by the χ2 superstatistical distribution with degree 2.

Methods of generating synthetic acoustic logs from resistivity logs for gas-hydrate-bearing sediments

USGS Publications Warehouse

Lee, Myung W.

1999-01-01

Methods of predicting acoustic logs from resistivity logs for hydrate-bearing sediments are presented. Modified time average equations derived from the weighted equation provide a means of relating the velocity of the sediment to the resistivity of the sediment. These methods can be used to transform resistivity logs into acoustic logs with or without using the gas hydrate concentration in the pore space. All the parameters except the unconsolidation constants, necessary for the prediction of acoustic log from resistivity log, can be estimated from a cross plot of resistivity versus porosity values. Unconsolidation constants in equations may be assumed without rendering significant errors in the prediction. These methods were applied to the acoustic and resistivity logs acquired at the Mallik 2L-38 gas hydrate research well drilled at the Mackenzie Delta, northern Canada. The results indicate that the proposed method is simple and accurate.

Fracture toughness of bleached enamel: Effect of applying three different nanobiomaterials by nanoindentation test.

PubMed

Khoroushi, Maryam; Mazaheri, Hamid; Saneie, Tahere; Samimi, Pouran

2016-01-01

Despite the absence of dispute about the efficacy of bleaching agents, a prime concern is about their compromising effect on the enamel structure. This in vitro study investigated whether the addition of three different biomaterials, including nano-bioactive glass (n-BG)/nano-hydroxy apetite (n-HA)/nano-amorphous calcium phosphate (n-ACP), to bleaching agents can affect the fracture toughness (FT) and vickers hardness number (VHN) of bovine enamel. The crowns of the newly extracted permanent bovine incisors teeth were separated from the root and sectioned along their central line; one half serving as the control specimen and the other half as the test specimen. After mounting and polishing procedure, all the control specimens (C) were subjected to nano-indentation test to obtain the baseline values of FT. Then, the control specimens were exposed to a 38% hydrogen peroxide for four times, each time for 10 min. The test specimens were divided into three groups and treated as follows, with the same protocol used for the control specimens: Group 1; ACP + hydrogen peroxide (HP) mixed gel; Group 2 BG + HP mixed gel; and Group 3 HA + HP mixed gel. FT measurements with nano-indentation were carried out subsequent to bleaching experiments. Data were analyzed using SPSS and Kruskal-Wallis test (α = 0.05). A significant difference in young's modulus (YM), VHN, and FT at baseline and subsequent to bleaching in control group was observed. However, no significant differences were found in YM, VHN, and FT between the test groups, compared to the respective baseline values. Under the limitations of the current study, it can be concluded that the n-HA, n-ACP, and n-BG could be potential biomaterials used to reduce the adverse effects of tooth bleaching.

Fracture toughness of bleached enamel: Effect of applying three different nanobiomaterials by nanoindentation test

PubMed Central

Khoroushi, Maryam; Mazaheri, Hamid; Saneie, Tahere; Samimi, Pouran

2016-01-01

Background: Despite the absence of dispute about the efficacy of bleaching agents, a prime concern is about their compromising effect on the enamel structure. This in vitro study investigated whether the addition of three different biomaterials, including nano-bioactive glass (n-BG)/nano-hydroxy apetite (n-HA)/nano-amorphous calcium phosphate (n-ACP), to bleaching agents can affect the fracture toughness (FT) and vickers hardness number (VHN) of bovine enamel. Materials and Methods: The crowns of the newly extracted permanent bovine incisors teeth were separated from the root and sectioned along their central line; one half serving as the control specimen and the other half as the test specimen. After mounting and polishing procedure, all the control specimens (C) were subjected to nano-indentation test to obtain the baseline values of FT. Then, the control specimens were exposed to a 38% hydrogen peroxide for four times, each time for 10 min. The test specimens were divided into three groups and treated as follows, with the same protocol used for the control specimens: Group 1; ACP + hydrogen peroxide (HP) mixed gel; Group 2 BG + HP mixed gel; and Group 3 HA + HP mixed gel. FT measurements with nano-indentation were carried out subsequent to bleaching experiments. Data were analyzed using SPSS and Kruskal–Wallis test (α = 0.05). Results: A significant difference in young's modulus (YM), VHN, and FT at baseline and subsequent to bleaching in control group was observed. However, no significant differences were found in YM, VHN, and FT between the test groups, compared to the respective baseline values. Conclusion: Under the limitations of the current study, it can be concluded that the n-HA, n-ACP, and n-BG could be potential biomaterials used to reduce the adverse effects of tooth bleaching. PMID:27307669

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil.

PubMed

Carmello, Juliana Cabrini; Fais, Laiza Maria Grassi; Ribeiro, Lígia Nunes de Moraes; Claro Neto, Salvador; Guaglianoni, Dalton Geraldo; Pinelli, Lígia Antunes Pereira

2012-02-01

The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. The aim of this study was to evaluate the diametral tensile strength (DTS) and film thickness (FT) of an experimental dental luting agent derived from castor oil (COP) with or without addition of different quantities of filler (calcium carbonate - CaCO3). Eighty specimens were manufactured (DTS N=40; FT N=40) and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control). The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min). For FT test, the cements were sandwiched between two glass plates (2 cm²) and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (α=0.05). The values of DTS (MPa) were: Pure COP- 10.94 ± 1.30; COP 10%- 30.06 ± 0.64; COP 50%- 29.87 ± 0.27; zinc phosphate- 4.88 ± 0.96. The values of FT (µm) were: Pure COP- 31.09 ± 3.16; COP 10%- 17.05 ± 4.83; COP 50%- 13.03 ± 4.83; Zinc Phosphate- 20.00 ± 0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10). The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness.

Diametral tensile strength and film thickness of an experimental dental luting agent derived from castor oil

PubMed Central

CARMELLO, Juliana Cabrini; FAIS, Laiza Maria Grassi; RIBEIRO, Lígia Nunes de Moraes; CLARO NETO, Salvador; GUAGLIANONI, Dalton Geraldo; PINELLI, Lígia Antunes Pereira

2012-01-01

The need to develop new dental luting agents in order to improve the success of treatments has greatly motivated research. Objective The aim of this study was to evaluate the diametral tensile strength (DTS) and film thickness (FT) of an experimental dental luting agent derived from castor oil (COP) with or without addition of different quantities of filler (calcium carbonate - CaCO3). Material and Methods Eighty specimens were manufactured (DTS N=40; FT N=40) and divided into 4 groups: Pure COP; COP 10%; COP 50% and zinc phosphate (control). The cements were mixed according to the manufacturers' recommendations and submitted to the tests. The DTS test was performed in the MTS 810 testing machine (10 KN, 0.5 mm/min). For FT test, the cements were sandwiched between two glass plates (2 cm2) and a load of 15 kg was applied vertically on the top of the specimen for 10 min. The data were analyzed by means of one-way ANOVA and Tukey's test (α=0.05). Results The values of DTS (MPa) were: Pure COP- 10.94±1.30; COP 10%- 30.06±0.64; COP 50%- 29.87±0.27; zinc phosphate- 4.88±0.96. The values of FT (µm) were: Pure COP- 31.09±3.16; COP 10%- 17.05±4.83; COP 50%- 13.03±4.83; Zinc Phosphate- 20.00±0.12. One-way ANOVA showed statistically significant differences among the groups (DTS - p=1.01E-40; FT - p=2.4E-10). Conclusion The experimental dental luting agent with 50% of filler showed the best diametral tensile strength and film thickness. PMID:22437672

Flight measured and calculated exhaust jet conditions for an F100 engine in an F-15 airplane

NASA Technical Reports Server (NTRS)

Hernandez, Francisco J.; Burcham, Frank W., Jr.

1988-01-01

The exhaust jet conditions, in terms of temperature and Mach number, were determined for a nozzle-aft end acoustic study flown on an F-15 aircraft. Jet properties for the F100 EMD engines were calculated using the engine manufacturer's specification deck. The effects of atmospheric temperature on jet Mach number, M10, were calculated. Values of turbine discharge pressure, PT6M, jet Mach number, and jet temperature were calculated as a function of aircraft Mach number, altitude, and power lever angle for the test day conditions. At a typical test point with a Mach number of 0.9, intermediate power setting, and an altitude of 20,000 ft, M10 was equal to 1.63. Flight measured and calculated values of PT6M were compared for intermediate power at altitudes of 15500, 20500, and 31000 ft. It was found that at 31000 ft, there was excellent agreement between both, but for lower altitudes the specification deck overpredicted the flight data. The calculated jet Mach numbers were believed to be accurate to within 2 percent.

Transference effects of prior non-contingent reinforcement on the acquisition of temporal control on fixed-interval schedules.

PubMed

López, Florente; Menez, Marina

2012-07-01

In two experiments we examined the influence of response and time factors on the speed of acquisition of temporal control on FI schedules. In Experiment 1, prior exposure to FT accelerated the development of temporal control on FI schedules of the same temporal value. It was also found that the slower acquisition on FI with prior RT was similar to that of rats with prior standard training. In Experiment 2, prior exposure to FT accelerated the development of temporal control on a FI schedule with a threefold increase in temporal value. Additionally, it was found that with prior FI 30s training, acquisition of temporal control on FI 90s was even faster than with prior FT 30s. Measures of head-entries into the feeder along the experiments indicated that temporal control was already developed during the periodic but not during the non-periodic histories and that this control transferred to lever press during FI testing phase. Copyright © 2012 Elsevier B.V. All rights reserved.

Androgen Concentrations in Umbilical Cord Blood and Their Association with Maternal, Fetal and Obstetric Factors

PubMed Central

Keelan, Jeffrey A.; Mattes, Eugen; Tan, HaiWei; Dinan, Andrew; Newnham, John P.; Whitehouse, Andrew J. O.; Jacoby, Peter; Hickey, Martha

2012-01-01

The aim of this study was to measure umbilical blood androgen concentrations in a birth cohort using a highly specific liquid chromatography-tandem mass spectrometry (LC-MS/MS) assay and assesses the effects of sex, labor, and gestational age on fetal androgen levels at birth. We performed a prospective cohort study of androgen concentrations in mixed arterial and venous umbilical cord serum from 803 unselected singleton pregnancies from a general obstetric population in Western Australia. Total testosterone (TT), Δ4-androstenedione, and dehydroepiandrosterone were extracted from archived cord serum samples and measured using LC-MS/MS. SHBG was measured by ELISA; free testosterone (FT) and bioavailable testosterone (BioT) values were also calculated. Median values for all three androgens were generally lower than previously published values. Levels of TT, FT, BioT, and SHBG were significantly higher in male verses female neonates (P<0.0001), while dehydroepiandrosterone levels were higher in females (P<0.0001). Labor was associated with a significant (∼15–26%) decrease in median cord blood TT and FT levels (both sexes combined), but a modest (∼16–31%) increase in SHBG, Δ4-androstenedione, and dehydroepiandrosterone concentrations. TT and FT were significantly negatively correlated with gestational age at delivery, while SHBG, Δ4-androstenedione, and dehydroepiandrosterone were positively correlated. Antenatal glucocorticoid administration also had a significant effect in the multiple regression models. This is the first study to report umbilical cord androgen levels in a large unselected population of neonates using LC-MS/MS. Our findings suggest that previous studies have over-estimated cord androgen levels, and that fetal, maternal, and obstetric factors influence cord androgen levels differentially. Caution should be exercised when interpreting previously-published data that have not taken all of these factors into account. PMID:22916165

Rapid and non-invasive analysis of deoxynivalenol in durum and common wheat by Fourier-Transform Near Infrared (FT-NIR) spectroscopy.

PubMed

De Girolamo, A; Lippolis, V; Nordkvist, E; Visconti, A

2009-06-01

Fourier transform near-infrared spectroscopy (FT-NIR) was used for rapid and non-invasive analysis of deoxynivalenol (DON) in durum and common wheat. The relevance of using ground wheat samples with a homogeneous particle size distribution to minimize measurement variations and avoid DON segregation among particles of different sizes was established. Calibration models for durum wheat, common wheat and durum + common wheat samples, with particle size <500 microm, were obtained by using partial least squares (PLS) regression with an external validation technique. Values of root mean square error of prediction (RMSEP, 306-379 microg kg(-1)) were comparable and not too far from values of root mean square error of cross-validation (RMSECV, 470-555 microg kg(-1)). Coefficients of determination (r(2)) indicated an "approximate to good" level of prediction of the DON content by FT-NIR spectroscopy in the PLS calibration models (r(2) = 0.71-0.83), and a "good" discrimination between low and high DON contents in the PLS validation models (r(2) = 0.58-0.63). A "limited to good" practical utility of the models was ascertained by range error ratio (RER) values higher than 6. A qualitative model, based on 197 calibration samples, was developed to discriminate between blank and naturally contaminated wheat samples by setting a cut-off at 300 microg kg(-1) DON to separate the two classes. The model correctly classified 69% of the 65 validation samples with most misclassified samples (16 of 20) showing DON contamination levels quite close to the cut-off level. These findings suggest that FT-NIR analysis is suitable for the determination of DON in unprocessed wheat at levels far below the maximum permitted limits set by the European Commission.

Combination of 1H nuclear magnetic resonance spectroscopy and principal component analysis to evaluate the lipid fluidity of flutamide-encapsulated lipid nanoemulsions.

PubMed

Takegami, Shigehiko; Ueyama, Keita; Konishi, Atsuko; Kitade, Tatsuya

2018-06-06

The lipid fluidity of various lipid nanoemulsions (LNEs) without and with flutamide (FT) and containing one of two neutral lipids, one of four phosphatidylcholines as a surfactant, and sodium palmitate as a cosurfactant was investigated by the combination of 1 H nuclear magnetic resonance (NMR) spectroscopy and principal component analysis (PCA). In the 1 H NMR spectra, the peaks from the methylene groups of the neutral lipids and surfactants for all LNE preparations showed downfield shifts with increasing temperature from 20 to 60 °C. PCA was applied to the 1 H NMR spectral data obtained for the LNEs. The PCA resulted in a model in which the first two principal components (PCs) extracted 88% of the total spectral variation; the first PC (PC-1) axis and second PC (PC-2) axis accounted for 73 and 15%, respectively, of the total spectral variation. The Score-1 values for PC-1 plotted against temperature revealed the existence of two clusters, which were defined by the neutral lipid of the LNE preparations. Meanwhile, the Score-2 values decreased with rising temperature and reflected the increase in lipid fluidity of each LNE preparation, consistent with fluorescence anisotropy measurements. In addition, the changes of Score-2 values with temperature for LNE preparations with FT were smaller than those for LNE preparations without FT. This indicates that FT encapsulated in LNE particles markedly suppressed the increase in lipid fluidity of LNE particles with rising temperature. Thus, PCA of 1 H NMR spectra will become a powerful tool to analyze the lipid fluidity of lipid nanoparticles. Graphical abstract ᅟ.

A comparison of preservative-free diclofenac and preserved diclofenac eye drops after cataract surgery in patients with diabetic retinopathy.

PubMed

Yasuda, Kanako; Miyazawa, Akiko; Shimura, Masahiko

2012-06-01

The aim of this study was to compare the anti-inflammatory efficacy of preservative-free and preserved 0.1% diclofenac eye drops for the management of postoperative inflammation after cataract surgery in patients with nonproliferative diabetic retinopathy and in normal controls. Forty-two diabetic patients and 50 normal control patients who underwent small-incision phacoemulsification cataract surgery bilaterally received topical preservative-free diclofenac in 1 eye and preserved diclofenac in the other eye. The corrected distance visual acuity (CDVA) as determined by a logarithm of the minimum angle of resolution (logMAR) chart, intraocular pressure (IOP), foveal thickness (FT) using optical coherence tomography (OCT), and the anterior chamber flare (ACF) score measured with a laser flare cell meter were monitored for 12 weeks after surgery. In the eyes with diabetic retinopathy, there were no significant differences in CDVA, IOP, FT, and ACF score between the right and left eyes at the initial exam. After cataract surgery, changes in CDVA, IOP, and FT were not influenced by the preservative in the diclofenac eye drops. In contrast, the ACF score in the eyes treated with preserved diclofenac showed slower recovery from postoperative inflammation than the eyes treated with preservative-free diclofenac. In the normal control eyes, similar but milder changes were observed in each of the clinical parameters. Because preservative suppressed the anti-inflammatory efficacy of topical diclofenac after cataract surgery, preservative-free diclofenac may have an improved safety profile during postoperative treatment, especially in patients with diabetic retinopathy.

Reservoir description is key to steamflood planning and implementation, Webster Reservoir, Midway-Sunset Field, Kern County, California

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, B.R.; Link, M.H.

1988-01-01

The Webster reservoir at Midway-Sunset field, Kern County, California, is an unconsolidated sand reservoir of Miocene age (''Stevens equivalent,'' Monterey Formation). The Webster was discovered in 1910 but, due to poor heavy oil (14/sup 0/ API) economics, development for primary production and subsequent enhanced recovery were sporadic. Currently, the reservoir produces by cyclic steam stimulation in approximately 35 wells. Cumulative oil production for the Webster since 1910 is about 13 million bbl. The Webster is subdivided into two reservoirs - the Webster Intermediate and Webster Main. The Webster Intermediate directly overlies the Webster Main in one area but it ismore » separated by up to 300 ft of shale elsewhere. The combined thickness of both Webster reservoirs averages 250 ft and is located at a drilling depth of 1,100-1,800 ft. From evaluation of modern core data and sand distribution maps, the Webster sands are interpreted to have been deposited by turbidity currents that flowed from southwest to northeast in this area. Oil is trapped in the Webster reservoir where these turbidites were subsequently folded on a northwest-southeast-trending anticline. Detailed recorrelation on wireline logs, stratigraphic zonation, detailed reservoir description by zone, and sedimentary facies identification in modern cores has led to development of a geologic model for the Webster. This model indicates that the Webster Intermediate was deposited predominately by strongly channelized turbidity currents, resulting in channel-fill sands, and that the Webster Main was deposited by less restricted flows, resulting in more lobate deposits.« less

Estimation of soil organic partition coefficients: from retention factors measured by soil column chromatography with water as eluent.

PubMed

Xu, Feng; Liang, Xinmiao; Lin, Bingcheng; Schramm, Karl-Werner; Kettrup, Antonius

2002-08-30

The retention factors (k) of 104 hydrophobic organic chemicals (HOCs) were measured in soil column chromatography (SCC) over columns filled with three naturally occurring reference soils and eluted with Milli-Q water. A novel method for the estimation of soil organic partition coefficient (Koc) was developed based on correlations with k in soil/water systems. Strong log Koc versus log k correlations (r>0.96) were found. The estimated Koc values were in accordance with the literature values with a maximum deviation of less than 0.4 log units. All estimated Koc values from three soils were consistent with each other. The SCC approach is promising for fast screening of a large number of chemicals in their environmental applications.

Detection of E. coli O157:H7 from ground beef using Fourier transform infrared (FT-IR) spectroscopy and chemometrics.

PubMed

Davis, Reeta; Irudayaraj, Joseph; Reuhs, Bradley L; Mauer, Lisa J

2010-08-01

FT-IR spectroscopy methods for detection, differentiation, and quantification of E. coli O157:H7 strains separated from ground beef were developed. Filtration and immunomagnetic separation (IMS) were used to extract live and dead E. coli O157:H7 cells from contaminated ground beef prior to spectral acquisition. Spectra were analyzed using chemometric techniques in OPUS, TQ Analyst, and WinDAS software programs. Standard plate counts were used for development and validation of spectral analyses. The detection limit based on a selectivity value using the OPUS ident test was 10(5) CFU/g for both Filtration-FT-IR and IMS-FT-IR methods. Experiments using ground beef inoculated with fewer cells (10(1) to 10(2) CFU/g) reached the detection limit at 6 h incubation. Partial least squares (PLS) models with cross validation were used to establish relationships between plate counts and FT-IR spectra. Better PLS predictions were obtained for quantifying live E. coli O157:H7 strains (R(2)> or = 0.9955, RMSEE < or = 0.17, RPD > or = 14) and different ratios of live and dead E. coli O157:H7 cells (R(2)= 0.9945, RMSEE = 2.75, RPD = 13.43) from ground beef using Filtration-FT-IR than IMS-FT-IR methods. Discriminant analysis and canonical variate analysis (CVA) of the spectra differentiated various strains of E. coli O157:H7 from an apathogenic control strain. CVA also separated spectra of 100% dead cells separated from ground beef from spectra of 0.5% live cells in the presence of 99.5% dead cells of E. coli O157:H7. These combined separation and FT-IR methods could be useful for rapid detection and differentiation of pathogens in complex foods.

Circulating concentrations of free thyroxine after an oral intake of liquid LT4 taken either during fasting conditions or at breakfast.

PubMed

Marina, Michela; Ceda, Gian Paolo; Aloe, Rosalia; Gnocchi, Cecilia; Ceresini, Graziano

2017-01-16

Liquid levothyroxine (LT4) given at breakfast normalizes TSH in hypothyroid patients. However, a few studies are available on circulating free thyroxine (FT4) concentrations after liquid vs solid LT4 preparations. During an "ad interim" analysis on serum FT4 after 200 mcg liquid LT4 consumption while fasting in thyroidectomized thyroid cancer patients, we found that seven subjects fortuitously took liquid LT4 at breakfast. As established in the original protocol, serum FT4 was measured both at baseline as well as at 3 and 4 hours after solid or liquid LT4 consumption. We compared serum profile of FT4 in these subjects with those obtained in other subjects participating in the same study who took liquid LT4 (n. 7 subjects) or solid LT4 (n. 7 subjects) while fasting. The percentage increase of circulating FT4 was calculated at the above reported peak-times over the baseline values. Circulating FT4 increased of about 40% in each group of subjects at both the 3rd and the 4th hour with no difference between these two time points in either group. The maximum FT4 % increase, irrespective of the time point, was 44.62 ± 3.05 (Mean ± SE), 44.84 ± 5.43, and 43.83 ± 1.30 after fasting solid, fasting liquid, and breakfast liquid LT4 consumption, respectively, with no differences among the three groups. Circulating FT4 obtained after 3 and 4 hours from the ingestion of 200 mcg liquid LT4 is not influenced by meal and is comparable with that observed after solid LT4 preparations ingested while fasting.

Associations of Triiodothyronine Levels with Carotid Atherosclerosis and Arterial Stiffness in Hemodialysis Patients

PubMed Central

Kircelli, Fatih; Asci, Gulay; Carrero, Juan Jesus; Gungor, Ozkan; Demirci, Meltem Sezis; Ozbek, Suha Sureyya; Ceylan, Naim; Ozkahya, Mehmet; Toz, Huseyin; Ok, Ercan

2011-01-01

Summary Background and objectives End-stage renal disease is linked to alterations in thyroid hormone levels and/or metabolism, resulting in a high prevalence of subclinical hypothyroidism and low triiodothyronine (T3) levels. These alterations are involved in endothelial damage, cardiac abnormalities, and inflammation, but the exact mechanisms are unclear. In this study, we investigated the relationship between serum free-T3 (fT3) and carotid artery atherosclerosis, arterial stiffness, and vascular calcification in prevalent patients on conventional hemodialysis. Design, setting, participants, & measurements 137 patients were included. Thyroid-hormone levels were determined by chemiluminescent immunoassay, carotid artery–intima media thickness (CA-IMT) by Doppler ultrasonography, carotid-femoral pulse wave velocity (c-f PWV), and augmentation index by Sphygmocor device, and coronary artery calcification (CAC) scores by multi-slice computerized tomography. Results Mean fT3 level was 3.70 ± 1.23 pmol/L. Across decreasing fT3 tertiles, c-f PWV and CA-IMT values were incrementally higher, whereas CACs were not different. In adjusted ordinal logistic regression analysis, fT3 level (odds ratio, 0.81; 95% confidence interval, 0.68 to 0.97), age, and interdialytic weight gain were significantly associated with CA-IMT. fT3 level was associated with c-f PWV in nondiabetics but not in diabetics. In nondiabetics (n = 113), c-f PWV was positively associated with age and systolic BP but negatively with fT3 levels (odds ratio = 0.57, 95% confidence interval 0.39 to 0.83). Conclusions fT3 levels are inversely associated with carotid atherosclerosis but not with CAC in hemodialysis patients. Also, fT3 levels are inversely associated with surrogates of arterial stiffness in nondiabetics. PMID:21836150

Low T3 syndrome as a predictor of poor prognosis in chronic lymphocytic leukemia.

PubMed

Gao, Rui; Chen, Rui-Ze; Xia, Yi; Liang, Jin-Hua; Wang, Li; Zhu, Hua-Yuan; Zhu Wu, Jia-; Fan, Lei; Li, Jian-Yong; Yang, Tao; Xu, Wei

2018-02-19

Low triiodothyronine (T3) state is associated with poor prognosis in critical acute and prolonged illness. However, the information on thyroid dysfunction and cancer is limited. The aim of our study was to evaluate the prognostic value of low T3 syndrome in chronic lymphocytic leukemia (CLL). Two hundred and fifty-eight patients with detailed thyroid hormone profile at CLL diagnosis were enrolled. Low T3 syndrome was defined by low free T3 (FT3) level accompanied by normal-to-low free tetraiodothyronine (FT4) and thyroid-stimulating hormone (TSH) levels. A propensity score-matched method was performed to balance the baseline characteristics. Multivariate Cox regression analyses screened the independent prognostic factors related to time-to-first-treatment (TTFT) and cancer-specific survival (CSS). Area under the curve (AUC) assessed the predictive accuracy of CLL-International Prognostic Index (IPI) together with low T3 syndrome. The results showed that 37 (14.34%) patients had low T3 syndrome, which was significantly associated with unfavorable TTFT and CSS in the propensity-matched cohort, and it was an independent prognostic indicator for both TTFT and CSS. Serum FT3 level was positively related to protein metabolism and anemia, and inversely related to inflammatory state. Patients with only low FT3 demonstrated better survival than those with synchronously low FT3 and FT4, while those with synchronously low FT3, FT4 and TSH had the worst clinical outcome. Low T3 syndrome together with CLL-IPI had larger AUCs compared with CLL-IPI alone in TTFT and CSS prediction. In conclusion, low T3 syndrome may be a good candidate for predicting prognosis in future clinical practice of CLL. © 2018 UICC.

Property-Structure-Processing Relations in Polymeric Materials.

DTIC Science & Technology

1981-07-31

increase indefinitely without indicating actual yield value and R which is a measure of the elastic character of the fluid, approaches a limiting value...appears to increase indefinitely without indicating an- actual yield value and R, which is a measure of the elastic character of the fluid, approaches a...a linear graph when log r is plotted against log x; i.e., ,I has a x" behavior at low x. Since a 0 1, this does not correspond to the classical yield

Relative effect potency estimates of dioxin-like activity for dioxins, furans, and dioxin-like PCBs in adults based on cytochrome P450 1A1 and 1B1 gene expression in blood.

PubMed

Wimmerová, Soňa; van den Berg, Martin; Chovancová, Jana; Patayová, Henrieta; Jusko, Todd A; van Duursen, Majorie B M; Palkovičová Murínová, Ľubica; Canton, Rocio F; van Ede, Karin I; Trnovec, Tomáš

2016-11-01

In the risk assessment of PCDDs, PCDFs, and dioxin-like (DL) PCBs, regulatory authorities support the use of the toxic equivalency factor (TEF)-scheme derived from a heterogeneous data set of the relative effect potency (REPs) estimates. We sought to determine REPs for dioxin-like compounds (DLCs) using expression of cytochrome P450 (CYP) 1A1 and 1B1 mRNA in human peripheral blood mononuclear cells representing two different pathways. We used a sex and age adjusted regression-based approach comparing the strength of association between each DLC and the cytochrome P450 (CYP) 1A1 and 1B1 mRNA expression in 320 adults residing in an organochlorine-polluted area of eastern Slovakia. We calculated REPs based on CYP1A1 expression for 4 PCDDs, 8 PCDFs, and 1 PCB congener, and based on CYP1B1 expression for 5 PCDFs and 11 PCB congeners. REPs from CYP1A1 correlated with REPs previously derived from thyroid volume (ρ=0.85; p<0.001) and serum FT4 (ρ=0.77; p=0.009). The 13 log REPs from CYP1A1 correlated with log WHO-TEFs (r=0.63; p=0.015) and 11 log PCB REPs with PCB consensus toxicity factors (CTFs) for compounds with WHO-TEFs (r=0.80; p=0.003). The complete set of derived 56 log REPs correlated with the log CTFs (r=0.77; p=0.001) and log WHO-TEFs (r=0.81; p<0.001). REPs calculated from thyroid and cytochrome P450 endpoints realistically reflect human exposure scenarios because they are based on human chronic and low-dose exposures. While the CYP 1A1 seems more suitable for toxicity evaluation of PCDD/Fs, the CYP 1B1 is more apt for PCDFs and PCBs and reflects different pathways. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analysis of ILRS Site Ties

NASA Astrophysics Data System (ADS)

Husson, V. S.; Long, J. L.; Pearlman, M.

2001-12-01

By the end of 2000, 94% of ILRS stations had completed station and site information forms (i.e. site logs). These forms contain six types of information. These six categories include site identifiers, contact information, approximate coordinates, system configuration history, system ranging capabilities, and local survey ties. The ILRS Central Bureau, in conjunction with the ILRS Networks and Engineering Working Group, has developed procedures to quality control site log contents. Part of this verification entails data integrity checks of local site ties and is the primary focus of this paper. Local survey ties are critical to the combination of space geodetic network coordinate solutions (i.e. GPS, SLR, VLBI, DORIS) of the International Terrestrial Reference Frame (ITRF). Approximately 90% of active SLR sites are collocated with at least one other space geodetic technique. The process used to verify these SLR ties, at collocated sites, is identical to the approach used in ITRF2000. Local vectors (X, Y, Z) from each ILRS site log are differenced from its corresponding ITRF2000 position vectors (i.e. no transformations). These X, Y, and Z deltas are converted into North, East, and Up. Any deltas, in any component, larger than 5 millimeter is flagged for investigation. In the absence of ITRF2000 SLR positions, CSR positions were used. To further enhance this comparison and to fill gaps in information, local ties contained in site logs from the other space geodetic services (i.e. IGS, IVS, IDS) were used in addition to ITRF2000 ties. Case studies of two collocated sites (McDonald/Ft. Davis and Hartebeeshtoek) will be explored in-depth. Recommendations on how local site surveys should be conducted and how this information should be managed will also be presented.

Applying the log-normal distribution to target detection

NASA Astrophysics Data System (ADS)

Holst, Gerald C.

1992-09-01

Holst and Pickard experimentally determined that MRT responses tend to follow a log-normal distribution. The log normal distribution appeared reasonable because nearly all visual psychological data is plotted on a logarithmic scale. It has the additional advantage that it is bounded to positive values; an important consideration since probability of detection is often plotted in linear coordinates. Review of published data suggests that the log-normal distribution may have universal applicability. Specifically, the log-normal distribution obtained from MRT tests appears to fit the target transfer function and the probability of detection of rectangular targets.

Autoregressive modeling for the spectral analysis of oceanographic data

NASA Technical Reports Server (NTRS)

Gangopadhyay, Avijit; Cornillon, Peter; Jackson, Leland B.

1989-01-01

Over the last decade there has been a dramatic increase in the number and volume of data sets useful for oceanographic studies. Many of these data sets consist of long temporal or spatial series derived from satellites and large-scale oceanographic experiments. These data sets are, however, often 'gappy' in space, irregular in time, and always of finite length. The conventional Fourier transform (FT) approach to the spectral analysis is thus often inapplicable, or where applicable, it provides questionable results. Here, through comparative analysis with the FT for different oceanographic data sets, the possibilities offered by autoregressive (AR) modeling to perform spectral analysis of gappy, finite-length series, are discussed. The applications demonstrate that as the length of the time series becomes shorter, the resolving power of the AR approach as compared with that of the FT improves. For the longest data sets examined here, 98 points, the AR method performed only slightly better than the FT, but for the very short ones, 17 points, the AR method showed a dramatic improvement over the FT. The application of the AR method to a gappy time series, although a secondary concern of this manuscript, further underlines the value of this approach.

Simultaneous determination of some artificial sweeteners in ternary formulations by FT-IR and EI-MS

NASA Astrophysics Data System (ADS)

Tosa, Nicoleta; Moldovan, Zaharie; Bratu, Ioan

2012-02-01

Artificial sweeteners are widely used in food, beverage and pharmaceutical industries all over the world. In this study some non-nutritive sweeteners such as aspartame, acesulfame-K, sodium cyclamate and sodium saccharin were simultaneously determined in ternary mixtures using FT-IR and EI-MS measurements. FT-IR method is based on direct measurements of the peak height values and area centered on 1736 cm-1, 836 cm-1, 2854 cm-1 and 1050 cm-1 for aspartame, acesulfame-K, sodium cyclamate and sodium saccharin, respectively. Mass spectrometry determinations show the characteristic peaks at m/z 91 and 262 for aspartame,m/z 43 and 163 acesulfame-K,m/z 83 and 97 for sodium cyclamate andm/z 104 and 183 for sodium saccharin. The results obtained by EI-MS in different formulations are in agreement with the FT-IR ones and provide also essential data concerning the purity grade of the components. It is concluded that FT-IR and EI-MS procedures developed in this work represent a fast, sensitive and low cost alternative in the quality control of such sweeteners in different ternary formulations.

Acute hypoxia and related symptoms on mild exertion at simulated altitudes below 3048 m.

PubMed

Smith, Adrian M

2007-10-01

Helicopter aircrew have reported features of hypoxia below 3048 m (10,000 ft). The aim of this study was to examine the effect of physical activity below 3048 m on the development of hypoxia. Six subjects exercised at 30 W and 60 W for 4 min at sea level, 610 m, 2134 m, and 2743 m (2000 ft, 7000 ft, and 9000 ft). There was an abrupt decrease in Spo2 once physical activity was commenced. This was small at sea level (1%) and 610 m (2.2%), however, the Spo2 fell by 4.3% at 2134 m and 5.5% at 2743 m (to Spo2 88.1% and 85.7%, respectively). Spo2 returned to near-resting values within 3 min of stopping exercise. Symptoms of hypoxia were reported significantly more frequently during activity than rest at each of the altitudes. Helicopter aircrew should be aware that physical activity as low as 2134 m can produce hypoxemia and symptoms of hypoxia similar to that which would normally be expected in a person resting at approximately 3658-4572 m (12,000-15,000 ft).

Molecular structure, FT-IR, FT-Raman, NMR studies and first order molecular hyperpolarizabilities by the DFT method of mirtazapine and its comparison with mianserin

NASA Astrophysics Data System (ADS)

Sagdinc, Seda G.; Sahinturk, Ayse Erbay

2013-03-01

Mirtazapine (±)-1,2,3,4,10,14b-hexahydro-2-methylpyrazino(2,1-a)pyrido(2,3-c)(2)benzazepine is a compound with antidepressant therapeutic effects. It is the 6-aza derivative of the tetracyclic antidepressant mianserin (±)-2-methyl-1,2,3,4,10,14b-hexahydrodibenzo[c,f]pyrazino[1,2-a]azepine. The FT-IR and FT-Raman spectra of mirtazapine have been recorded in 4000-400 cm-1 and 3500-10 cm-1, respectively. The optimized geometry, energies, nonlinear optical properties, vibrational frequencies, 13C, 1H and 15N NMR chemical shift values of mirtazapine have been determined using the density functional theory (DFT/B3LYP) method. A comparison of the experimental and theoretical results of mirtazapine indicates that the density-functional B3LYP method is able to provide satisfactory results for predicting vibrational and NMR properties. The experimental and calculated results for mirtazapine have also been compared with mianserin.

Evaluation of Hologic Aptima HIV-1 Quant Dx Assay on the Panther System on HIV Subtypes

PubMed Central

Hack, Holly R.; Nair, Sangeetha V.; Worlock, Andrew; Malia, Jennifer A.; Peel, Sheila A.; Jagodzinski, Linda L.

2016-01-01

Quantitation of the HIV-1 viral load in plasma is the current standard of care for clinical monitoring of HIV-infected individuals undergoing antiretroviral therapy. This study evaluated the analytical and clinical performances of the Aptima HIV-1 Quant Dx assay (Hologic, San Diego, CA) for monitoring viral load by using 277 well-characterized subtype samples, including 171 cultured virus isolates and 106 plasma samples from 35 countries, representing all major HIV subtypes, recombinants, and circulating recombinant forms (CRFs) currently in circulation worldwide. Linearity of the Aptima assay was tested on each of 6 major HIV-1 subtypes (A, B, C, D, CRF01_AE, and CRF02_AG) and demonstrated an R2 value of ≥0.996. The performance of the Aptima assay was also compared to those of the Roche COBAS AmpliPrep/COBAS TaqMan HIV-1 v.2 (CAP/CTM) and Abbott m2000 RealTime HIV-1 (RealTime) assays on all subtype samples. The Aptima assay values averaged 0.21 log higher than the CAP/CTM values and 0.30 log higher than the RealTime values, and the values were >0.4 log higher than CAP/CTM values for subtypes F and G and than RealTime values for subtypes C, F, and G and CRF02_AG. Two samples demonstrated results with >1-log differences from RealTime results. When the data were adjusted by the average difference, 94.9% and 87.0% of Aptima results fell within 0.5 log of the CAP/CTM and RealTime results, respectively. The linearity and accuracy of the Aptima assay in correctly quantitating all major HIV-1 subtypes, coupled with the completely automated format and high throughput of the Panther system, make this system well suited for reliable measurement of viral load in the clinical laboratory. PMID:27510829

Evaluation of Hologic Aptima HIV-1 Quant Dx Assay on the Panther System on HIV Subtypes.

PubMed

Manak, Mark M; Hack, Holly R; Nair, Sangeetha V; Worlock, Andrew; Malia, Jennifer A; Peel, Sheila A; Jagodzinski, Linda L

2016-10-01

Quantitation of the HIV-1 viral load in plasma is the current standard of care for clinical monitoring of HIV-infected individuals undergoing antiretroviral therapy. This study evaluated the analytical and clinical performances of the Aptima HIV-1 Quant Dx assay (Hologic, San Diego, CA) for monitoring viral load by using 277 well-characterized subtype samples, including 171 cultured virus isolates and 106 plasma samples from 35 countries, representing all major HIV subtypes, recombinants, and circulating recombinant forms (CRFs) currently in circulation worldwide. Linearity of the Aptima assay was tested on each of 6 major HIV-1 subtypes (A, B, C, D, CRF01_AE, and CRF02_AG) and demonstrated an R(2) value of ≥0.996. The performance of the Aptima assay was also compared to those of the Roche COBAS AmpliPrep/COBAS TaqMan HIV-1 v.2 (CAP/CTM) and Abbott m2000 RealTime HIV-1 (RealTime) assays on all subtype samples. The Aptima assay values averaged 0.21 log higher than the CAP/CTM values and 0.30 log higher than the RealTime values, and the values were >0.4 log higher than CAP/CTM values for subtypes F and G and than RealTime values for subtypes C, F, and G and CRF02_AG. Two samples demonstrated results with >1-log differences from RealTime results. When the data were adjusted by the average difference, 94.9% and 87.0% of Aptima results fell within 0.5 log of the CAP/CTM and RealTime results, respectively. The linearity and accuracy of the Aptima assay in correctly quantitating all major HIV-1 subtypes, coupled with the completely automated format and high throughput of the Panther system, make this system well suited for reliable measurement of viral load in the clinical laboratory. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Measurement of polyurethane foam - air partition coefficients for semivolatile organic compounds as a function of temperature: Application to passive air sampler monitoring.

PubMed

Francisco, Ana Paula; Harner, Tom; Eng, Anita

2017-05-01

Polyurethane foam - air partition coefficients (K PUF-air ) for 9 polycyclic aromatic hydrocarbons (PAHs), 10 alkyl-substituted PAHs, 4 organochlorine pesticides (OCPs) and dibenzothiophene were measured as a function of temperature over the range 5 °C-35 °C, using a generator column approach. Enthalpies of PUF-to-air transfer (ΔH PUF-air , kJ/mol) were determined from the slopes of log K PUF-air versus 1000/T (K), and have an average value of 81.2 ± 7.03 kJ/mol. The log K PUF-air values at 22 °C ranged from 4.99 to 7.25. A relationship for log K PUF-air versus log K OA was shown to agree with a previous relationship based on only polychlorinated biphenyls (PCBs) and derived from long-term indoor uptake study experiments. The results also confirm that the existing K OA -based model for predicting log K PUF-air values is accurate. This new information is important in the derivation of uptake profiles and effective air sampling volumes for PUF disk samplers so that results can be reported in units of concentration in air. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

FT-IR, FT-Raman and UV-visible spectra of potassium 3-furoyltrifluoroborate salt

NASA Astrophysics Data System (ADS)

Iramain, Maximiliano A.; Davies, Lilian; Brandán, Silvia Antonia

2018-04-01

The potassium 3-furoyltrifluoroborate salt has been experimentally characterized by means of FT-IR, FT-Raman and UV-Visible spectroscopies. Here, the predicted FT-IR, FT-Raman and UV-visible spectra by using theoretical B3LYP/6-31G* and 6-311++G** calculations show very good correlations with the corresponding experimental ones. The solvation energies were predicted by using both levels of calculations. The NBO analyses reveal the high stability of the salt by using the B3LYP/6-31G* level of theory while the AIM studies evidence the ionic characteristics of the salt in both media. The strong blue colour observed on the K atom by using the molecular electrostatic potential mapped suggests that this region act as typical electrophilic site. The gap values have revealed that the salt in gas phase is more reactive than in solution, as was reported in the literature while, the F13⋯H6 interaction together with the Ksbnd O bond observed by the studies of their charges could probably modulate the reactivities of this salt in aqueous solution. The force fields were computed with the SQMFF methodology and the Molvib program to perform the complete vibrational analysis. Then, the 39 vibration normal modes classified as 26 A'+ 13 A″ were completely assigned and their force constants are also reported.

Non-destructive technique for determining the viability of soybean (Glycine max) seeds using FT-NIR spectroscopy.

PubMed

Kusumaningrum, Dewi; Lee, Hoonsoo; Lohumi, Santosh; Mo, Changyeun; Kim, Moon S; Cho, Byoung-Kwan

2018-03-01

The viability of seeds is important for determining their quality. A high-quality seed is one that has a high capability of germination that is necessary to ensure high productivity. Hence, developing technology for the detection of seed viability is a high priority in agriculture. Fourier transform near-infrared (FT-NIR) spectroscopy is one of the most popular devices among other vibrational spectroscopies. This study aims to use FT-NIR spectroscopy to determine the viability of soybean seeds. Viable and artificial ageing seeds as non-viable soybeans were used in this research. The FT-NIR spectra of soybean seeds were collected and analysed using a partial least-squares discriminant analysis (PLS-DA) to classify viable and non-viable soybean seeds. Moreover, the variable importance in projection (VIP) method for variable selection combined with the PLS-DA was employed. The most effective wavelengths were selected by the VIP method, which selected 146 optimal variables from the full set of 1557 variables. The results demonstrated that the FT-NIR spectral analysis with the PLS-DA method that uses all variables or the selected variables showed good performance based on the high value of prediction accuracy for soybean viability with an accuracy close to 100%. Hence, FT-NIR techniques with a chemometric analysis have the potential for rapidly measuring soybean seed viability. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

FTree query construction for virtual screening: a statistical analysis.

PubMed

Gerlach, Christof; Broughton, Howard; Zaliani, Andrea

2008-02-01

FTrees (FT) is a known chemoinformatic tool able to condense molecular descriptions into a graph object and to search for actives in large databases using graph similarity. The query graph is classically derived from a known active molecule, or a set of actives, for which a similar compound has to be found. Recently, FT similarity has been extended to fragment space, widening its capabilities. If a user were able to build a knowledge-based FT query from information other than a known active structure, the similarity search could be combined with other, normally separate, fields like de-novo design or pharmacophore searches. With this aim in mind, we performed a comprehensive analysis of several databases in terms of FT description and provide a basic statistical analysis of the FT spaces so far at hand. Vendors' catalogue collections and MDDR as a source of potential or known "actives", respectively, have been used. With the results reported herein, a set of ranges, mean values and standard deviations for several query parameters are presented in order to set a reference guide for the users. Applications on how to use this information in FT query building are also provided, using a newly built 3D-pharmacophore from 57 5HT-1F agonists and a published one which was used for virtual screening for tRNA-guanine transglycosylase (TGT) inhibitors.

FTree query construction for virtual screening: a statistical analysis

NASA Astrophysics Data System (ADS)

Gerlach, Christof; Broughton, Howard; Zaliani, Andrea

2008-02-01

FTrees (FT) is a known chemoinformatic tool able to condense molecular descriptions into a graph object and to search for actives in large databases using graph similarity. The query graph is classically derived from a known active molecule, or a set of actives, for which a similar compound has to be found. Recently, FT similarity has been extended to fragment space, widening its capabilities. If a user were able to build a knowledge-based FT query from information other than a known active structure, the similarity search could be combined with other, normally separate, fields like de-novo design or pharmacophore searches. With this aim in mind, we performed a comprehensive analysis of several databases in terms of FT description and provide a basic statistical analysis of the FT spaces so far at hand. Vendors' catalogue collections and MDDR as a source of potential or known "actives", respectively, have been used. With the results reported herein, a set of ranges, mean values and standard deviations for several query parameters are presented in order to set a reference guide for the users. Applications on how to use this information in FT query building are also provided, using a newly built 3D-pharmacophore from 57 5HT-1F agonists and a published one which was used for virtual screening for tRNA-guanine transglycosylase (TGT) inhibitors.