CH3NH3PbI3 grain growth and interfacial properties in meso-structured perovskite solar cells fabricated by two-step deposition.

PubMed

Yao, Zhibo; Wang, Wenli; Shen, Heping; Zhang, Ye; Luo, Qiang; Yin, Xuewen; Dai, Xuezeng; Li, Jianbao; Lin, Hong

2017-01-01

Although the two-step deposition (TSD) method is widely adopted for the high performance perovskite solar cells (PSCs), the CH 3 NH 3 PbI 3 perovskite crystal growth mechanism during the TSD process and the photo-generated charge recombination dynamics in the mesoporous-TiO 2 (mp-TiO 2 )/CH 3 NH 3 PbI 3 /hole transporting material (HTM) system remains unexploited. Herein, we modified the concentration of PbI 2 ( C (PbI2) ) solution to control the perovskite crystal properties, and observed an abnormal CH 3 NH 3 PbI 3 grain growth phenomenon atop mesoporous TiO 2 film. To illustrate this abnormal grain growth mechanism, we propose that a grain ripening process is taking place during the transformation from PbI 2 to CH 3 NH 3 PbI 3 , and discuss the PbI 2 nuclei morphology, perovskite grain growing stage, as well as Pb:I atomic ratio difference among CH 3 NH 3 PbI 3 grains with different morphology. These C (PbI2) -dependent perovskite morphologies resulted in varied charge carrier transfer properties throughout the mp-TiO 2 /CH 3 NH 3 PbI 3 /HTM hybrid, as illustrated by photoluminescence measurement. Furthermore, the effect of CH 3 NH 3 PbI 3 morphology on light absorption and interfacial properties is investigated and correlated with the photovoltaic performance of PSCs.

Theoretical insights into aggregation-induced helicity modulation of a perylene bisimide derivative.

PubMed

Liang, Lijun; Li, Xin

2018-02-12

Formation of helical chiroptical self-assemblies via noncovalent interaction is a widely observed phenomenon in nature, the mechanism of which remains insufficiently understood. Employing an amphiphilic perylene-sugar dyad molecule (PBI-HAG) as an example, we report that the modulatable supramolecular helicity may emerge from an aggregating process that is dominated by competition between two types of noncovalent interaction: hydrogen bonding and π-π stacking. The interplay between these two driving forces, which is greatly affected by the solvent environment, determines the morphology the supramolecular assembly of PBI-HAGs. In particular, a non-layered supramolecular structure was formed in octane owing to stabilization effects of intermolecular hydrogen bonds, whereas a layered supramolecular structure was formed in water because of energetically favorable π-π stacking of aromatic rings. The formation of distinct supramolecular architectures in different solvents was reinforced by simulated circular dichroism spectra, which show opposite signals consistent with experimental observations. The results of this study could help us understand aggregation-induced supramolecular chirality of noncovalent self-assemblies. Graphical abstract Left Typical structures of amphiphilic perylene-sugar dyad (PBI-HAG) aggregates in different octane and water. Right Simulated CD and UV-Vis spectra of core PBIs aggregates in octane and water.

Polymer Fabric Protects Firefighters, Military, and Civilians

NASA Technical Reports Server (NTRS)

2008-01-01

In 1967, NASA contracted with Celanese Corporation, of New York, to develop a line of PBI textiles for use in space suits and vehicles. In 2005, the PBI fiber and polymer business was sold to PBI Performance Products Inc., of Charlotte, North Carolina, under the ownership of the InterTech Group, of North Charleston, South Carolina. PBI Performance Products now offers two distinct lines: PBI, the original heat and flame resistant fiber; and Celazole, a family of high-temperature PBI polymers available in true polymer form. PBI is now used in numerous firefighting, military, motor sports, and other applications.

Ventromedial prefrontal cortex modulates fatigue after penetrating traumatic brain injury

PubMed Central

Pardini, Matteo; Krueger, Frank; Raymont, Vanessa; Grafman, Jordan

2010-01-01

Background: Fatigue is a common and disabling symptom in neurologic disorders including traumatic penetrating brain injury (PBI). Despite fatigue's prevalence and impact on quality of life, its pathophysiology is not understood. Studies on effort perception in healthy subjects, animal behavioral paradigms, and recent evidence in different clinical populations suggest that ventromedial prefrontal cortex could play a significant role in fatigue pathophysiology in neurologic conditions. Methods: We enrolled 97 PBI patients and 37 control subjects drawn from the Vietnam Head Injury Study registry. Fatigue was assessed with a self-report questionnaire and a clinician-rated instrument; lesion location and volume were evaluated on CT scans. PBI patients were divided in 3 groups according to lesion location: a nonfrontal lesion group, a ventromedial prefrontal cortex lesion (vmPFC) group, and a dorso/lateral prefrontal cortex (d/lPFC) group. Fatigue scores were compared among the 3 PBI groups and the healthy controls. Results: Individuals with vmPFC lesions were significantly more fatigued than individuals with d/lPFC lesions, individuals with nonfrontal lesions, and healthy controls, while these 3 latter groups were equally fatigued. VmPFC volume was correlated with fatigue scores, showing that the larger the lesion volume, the higher the fatigue scores. Conclusions: We demonstrated that ventromedial prefrontal cortex lesion (vmPFC) plays a critical role in penetrating brain injury–related fatigue, providing a rationale to link fatigue to different vmPFC functions such as effort and reward perception. The identification of the anatomic and cognitive basis of fatigue can contribute to developing pathophysiology-based treatments for this disabling symptom. GLOSSARY AAL = Automated Anatomic Labeling; ANOVA = analysis of variance; BDI = Beck Depression Inventory; d/lPFC = dorso/lateral prefrontal cortex; DSM-IV = Diagnostic and Statistical Manual of Mental Disorders, 4th edition; NBRS = Neurobehavioral Rating Scale; NF = nonfrontal lesion; PBI = penetrating brain injury; ROI = region of interest; SCID-I = Structured Clinical Interview for DSM-IV, Axis I; VHIS = Vietnam Head Injury Study; vmPFC = ventromedial prefrontal cortex lesion. PMID:20194914

Patient Preferences and Physician Practice Patterns Regarding Breast Radiotherapy

DTIC Science & Technology

2011-01-01

breast irradiation (HF-WBI) 62%, partial breast irradiation ( PBI ) 28%, and conventionally fractionated whole breast irradiation (CF-WBI) 10%. By...comparison, 82% of physicians use CF-WBI for more than 2/3 of women and 56% never use HF-WBI. With respect to PBI , 62% of women preferred three...dimensional (3D)- PBI and 38% favor brachytherapy- PBI , whereas 36% of physicians offer 3D- PBI and 66% offer brachytherapy- PBI . 70% of women prefer once-daily

Electron–Rotor Interaction in Organic–Inorganic Lead Iodide Perovskites Discovered by Isotope Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, Jue; Yang, Mengjin; Ma, Xiangchao

We report on the carrier-rotor coupling effect in perovskite organic-inorganic hybrid lead iodide (CH3NH3PbI3) compounds discovered by isotope effects. Deuterated organic-inorganic perovskite compounds including CH3ND3PbI3, CD3NH3PbI3, and CD3ND3PbI3 were synthesized. Devices made from regular CH3NH3PbI3 and deuterated CH3ND3PbI3 exhibit comparable performance in band gap, current-voltage, carrier mobility, and power conversion efficiency. However, a time-resolved photoluminescence (TRPL) study reveals that CH3NH3PbI3 exhibits notably longer carrier lifetime than that of CH3ND3PbI3, in both thin-film and single crystal formats. Furthermore, the comparison in carrier lifetime between CD3NH3PbI3 and CH3ND3PbI3 single crystals suggests that vibrational modes in methylammonium (MA(+)) have little impact on carriermore » lifetime. In contrast, the fully deuterated compound CD3ND3PbI3 reconfirmed the trend of decreasing carrier lifetime upon the increasing moment of inertia of cationic MA(+). Polaron model elucidates the electron-rotor interaction.« less

Electron–Rotor Interaction in Organic–Inorganic Lead Iodide Perovskites Discovered by Isotope Effects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, Jue; Yang, Mengjin; Ma, Xiangchao

We report on the carrier-rotor coupling effect in perovskite organic-inorganic hybrid lead iodide (CH3NH3PbI3) compounds discovered by isotope effects. Deuterated organic-inorganic perovskite compounds including CH3ND3PbI3, CD3NH3PbI3, and CD3ND3PbI3 were synthesized. Devices made from regular CH3NH3PbI3 and deuterated CH3ND3PbI3 exhibit comparable performance in band gap, current-voltage, carrier mobility, and power conversion efficiency. However, a time-resolved photoluminescence (TRPL) study reveals that CH3NH3PbI3 exhibits notably longer carrier lifetime than that of CH3ND3PbI3, in both thin-film and single-crystal formats. Furthermore, the comparison in carrier lifetime between CD3NH3PbI3 and CH3ND3PbI3 single crystals suggests that vibrational modes in methylammonium (MA+) have little impact on carrier lifetime.more » In contrast, the fully deuterated compound CD3ND3PbI3 reconfirmed the trend of decreasing carrier lifetime upon the increasing moment of inertia of cationic MA+. Polaron model elucidates the electron-rotor interaction.« less

Electron-Rotor Interaction in Organic-Inorganic Lead Iodide Perovskites Discovered by Isotope Effects.

PubMed

Gong, Jue; Yang, Mengjin; Ma, Xiangchao; Schaller, Richard D; Liu, Gang; Kong, Lingping; Yang, Ye; Beard, Matthew C; Lesslie, Michael; Dai, Ying; Huang, Baibiao; Zhu, Kai; Xu, Tao

2016-08-04

We report on the carrier-rotor coupling effect in perovskite organic-inorganic hybrid lead iodide (CH3NH3PbI3) compounds discovered by isotope effects. Deuterated organic-inorganic perovskite compounds including CH3ND3PbI3, CD3NH3PbI3, and CD3ND3PbI3 were synthesized. Devices made from regular CH3NH3PbI3 and deuterated CH3ND3PbI3 exhibit comparable performance in band gap, current-voltage, carrier mobility, and power conversion efficiency. However, a time-resolved photoluminescence (TRPL) study reveals that CH3NH3PbI3 exhibits notably longer carrier lifetime than that of CH3ND3PbI3, in both thin-film and single-crystal formats. Furthermore, the comparison in carrier lifetime between CD3NH3PbI3 and CH3ND3PbI3 single crystals suggests that vibrational modes in methylammonium (MA(+)) have little impact on carrier lifetime. In contrast, the fully deuterated compound CD3ND3PbI3 reconfirmed the trend of decreasing carrier lifetime upon the increasing moment of inertia of cationic MA(+). Polaron model elucidates the electron-rotor interaction.

A simple fabrication of CH3NH3PbI3 perovskite for solar cells using low-purity PbI2

NASA Astrophysics Data System (ADS)

Guo, Nanjie; Zhang, Taiyang; Li, Ge; Xu, Feng; Qian, Xufang; Zhao, Yixin

2017-01-01

The CH3NH3PbI3 (MAPbI3) perovskite was usually prepared by high-purity PbI2 with high cost. The low cost and low-purity PbI2 was seldom reported for fabrication of MAPbI3 because it cannot even dissolve well in widely adopted solvent of DMF. We developed an easy method to adapt low-purity PbI2 for fabrication of high quality MAPbI3 just by the simple addition of some hydrochloric acid into the mixture of low-purity PbI2, MAI and DMF. This straightforward method can not only help dissolve the low quality PbI2 by reacting with some impurities in DMF, but also lead to a successful fabrication of high-quality perovskite solar cells with up to 14.80% efficiency comparable to the high quality PbI2 precursors. Project supported by the National Natural Science Foundation of China (Nos. 51372151, 21303103) and Houyingdong Grant (No. 151046).

CH3NH3PbI3 grain growth and interfacial properties in meso-structured perovskite solar cells fabricated by two-step deposition

NASA Astrophysics Data System (ADS)

Yao, Zhibo; Wang, Wenli; Shen, Heping; Zhang, Ye; Luo, Qiang; Yin, Xuewen; Dai, Xuezeng; Li, Jianbao; Lin, Hong

2017-12-01

Although the two-step deposition (TSD) method is widely adopted for the high performance perovskite solar cells (PSCs), the CH3NH3PbI3 perovskite crystal growth mechanism during the TSD process and the photo-generated charge recombination dynamics in the mesoporous-TiO2 (mp-TiO2)/CH3NH3PbI3/hole transporting material (HTM) system remains unexploited. Herein, we modified the concentration of PbI2 (C(PbI2)) solution to control the perovskite crystal properties, and observed an abnormal CH3NH3PbI3 grain growth phenomenon atop mesoporous TiO2 film. To illustrate this abnormal grain growth mechanism, we propose that a grain ripening process is taking place during the transformation from PbI2 to CH3NH3PbI3, and discuss the PbI2 nuclei morphology, perovskite grain growing stage, as well as Pb:I atomic ratio difference among CH3NH3PbI3 grains with different morphology. These C(PbI2)-dependent perovskite morphologies resulted in varied charge carrier transfer properties throughout the mp-TiO2/CH3NH3PbI3/HTM hybrid, as illustrated by photoluminescence measurement. Furthermore, the effect of CH3NH3PbI3 morphology on light absorption and interfacial properties is investigated and correlated with the photovoltaic performance of PSCs.

Spatial Distribution of Lead Iodide and Local Passivation on Organo-Lead Halide Perovskite.

PubMed

Chen, Sheng; Wen, Xiaoming; Yun, Jae S; Huang, Shujuan; Green, Martin; Jeon, Nam Joong; Yang, Woon Seok; Noh, Jun Hong; Seo, Jangwon; Seok, Sang Il; Ho-Baillie, Anita

2017-02-22

We identify nanoscale spatial distribution of PbI 2 on the (FAPbI 3 ) 0.85 (MAPbBr 3 ) 0.15 perovskite thin film and investigate the local passivation effect using confocal based optical microscopy of steady state and time-resolved photoluminescence (PL). Different from a typical scanning electron microscope (SEM) morphology study, confocal based PL spectroscopy and microscopy allow researchers to map the morphologies of both perovskite and PbI 2 grains simultaneously, by selectively detecting their characteristic fluorescent bands using band-pass filters. In this work, we compare the perovskite samples without and with excess PbI 2 incorporation and unambiguously reveal PbI 2 distribution for the PbI 2 -rich sample. In addition, using the nanoscale time-resolved PL technique we show that the PbI 2 -rich regions exhibit longer lifetime due to suppressed defect trapping, compared to the PbI 2 -poor regions. The measurement on the PbI 2 -rich sample indicates that the passivation effect of PbI 2 in perovskite film is effective, especially in localized regions. Hence, this finding is important for further improvement of the solar cells by considering the strategy of excess PbI 2 incorporation.

Blended polybenzimidazole and melamine-co-formaldehyde thermosets

DOE PAGES

Klaehn, John R.; Orme, Christopher J.; Peterson, Eric S.

2016-05-11

Polybenzimidazole [PBI; poly-2,2’(m-phenylene)-5,5’-bibenzimidazole] is known to have excellent high temperature stability (up to 450 ºC) and superb H 2/CO 2 selectivity compared to most high performance (HP) polymers. But, PBI has issues in thin-film formation compared to other HP polymers, due to challenging processing techniques. In this work, new blended thermosets were made with PBI and poly(melamine co-formaldehyde) [PMF] to produce stable thin-films after thermal processing at 220-250 ºC. PBI film formation is difficult, and the film tends to fracture and fissure due to loss of processing aids and stabilizers (salt/acid additives) that are found in PBI solutions above10 wtmore » %. The PBI-PMF blended thermosets we report do not have stabilizers, and can be made into dense thin-films. It is remarkable that these thermally processed PBI-PMF films were stable in deionized water for extended periods, whereas many PBI films that contain additives are not. The PBI-PMF films were analyzed using pure and mixed gas permeability measurement techniques. At 250 °C, the data show H 2/CO 2 gas selectivities greater than 13. Also, from the gas permeation data, the energy of activation (Ep) of a mixed gas stream for PBI-PMF shows that hydrogen permeates more easily than the other gases, while the permeabilities for the larger kinetic diameter gases are greatly diminished. The FT-IR spectra show that the PBI-PMF films have changed from parent PBI after thermal processing, and PMF dominates the spectra even in minor percent compositions. Altogether, the reported PBI-PMF thermoset films show good stability which can be used for high temperature gas separation.« less

Blended polybenzimidazole and melamine-co-formaldehyde thermosets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klaehn, John R.; Orme, Christopher J.; Peterson, Eric S.

Polybenzimidazole [PBI; poly-2,2’(m-phenylene)-5,5’-bibenzimidazole] is known to have excellent high temperature stability (up to 450 ºC) and superb H 2/CO 2 selectivity compared to most high performance (HP) polymers. But, PBI has issues in thin-film formation compared to other HP polymers, due to challenging processing techniques. In this work, new blended thermosets were made with PBI and poly(melamine co-formaldehyde) [PMF] to produce stable thin-films after thermal processing at 220-250 ºC. PBI film formation is difficult, and the film tends to fracture and fissure due to loss of processing aids and stabilizers (salt/acid additives) that are found in PBI solutions above10 wtmore » %. The PBI-PMF blended thermosets we report do not have stabilizers, and can be made into dense thin-films. It is remarkable that these thermally processed PBI-PMF films were stable in deionized water for extended periods, whereas many PBI films that contain additives are not. The PBI-PMF films were analyzed using pure and mixed gas permeability measurement techniques. At 250 °C, the data show H 2/CO 2 gas selectivities greater than 13. Also, from the gas permeation data, the energy of activation (Ep) of a mixed gas stream for PBI-PMF shows that hydrogen permeates more easily than the other gases, while the permeabilities for the larger kinetic diameter gases are greatly diminished. The FT-IR spectra show that the PBI-PMF films have changed from parent PBI after thermal processing, and PMF dominates the spectra even in minor percent compositions. Altogether, the reported PBI-PMF thermoset films show good stability which can be used for high temperature gas separation.« less

Polybenzimidazole compounds, polymeric media, and methods of post-polymerization modifications

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Wertsching, Alan K [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Luther, Thomas A [Idaho Falls, ID; Jones, Michael G [Pocatello, ID

2007-08-21

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with an organic-inorganic hybrid moiety. At least 85% of the imidazole nitrogens may be substituted. The organic-inorganic hybrid moiety may be an organosilane moiety, for example, (R)Me.sub.2SiCH.sub.2-- where R is selected from among methyl, phenyl, vinyl, and allyl. The PBI compound may exhibit similar thermal properties in comparison to the unsubstituted PBI. The PBI compound may exhibit a solubility in an organic solvent greater than the solubility of the unsubstituted PBI. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may occur at about room temperature and/or at about atmospheric pressure. Substituting may use at least 5 equivalents in relation to the imidazole nitrogens to be substituted or, preferably, about 15.

Polybenzimidazole compounds

DOEpatents

Klaehn, John R.; Peterson, Eric S.; Wertsching, Alan K.; Orme, Christopher J.; Luther, Thomas A.; Jones, Michael G.

2010-08-10

A PBI compound that includes imidazole nitrogens, at least a portion of which are substituted with an organic-inorganic hybrid moiety. At least 85% of the imidazole nitrogens may be substituted. The organic-inorganic hybrid moiety may be an organosilane moiety, for example, (R)Me.sub.2SiCH.sub.2--, where R is selected from among methyl, phenyl, vinyl, and allyl. The PBI compound may exhibit similar thermal properties in comparison to the unsubstituted PBI. The PBI compound may exhibit a solubility in an organic solvent greater than the solubility of the unsubstituted PBI. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may occur at about room temperature and/or at about atmospheric pressure. Substituting may use at least five equivalents in relation to the imidazole nitrogens to be substituted or, preferably, about fifteen equivalents.

A randomized trial evaluating a parent based intervention to reduce college drinking.

PubMed

Doumas, Diana M; Turrisi, Rob; Ray, Anne E; Esp, Susan M; Curtis-Schaeffer, Amy K

2013-07-01

This study evaluated the effectiveness of a parent based intervention (PBI) in reducing drinking among first year college students (N=443). Students were assigned to one of three conditions: PBI, PBI plus booster brochures (PBI-B), and an assessment only control group (CNT). At a 4-month post-intervention follow-up, results indicated students in the PBI-B group reported significantly less drinking to intoxication and peak drinking relative to the PBI group and CNT group. No significant differences were found between the PBI group and CNT group. Results provide further support for PBIs to reduce college student drinking and suggest that a booster brochure increases the effectiveness of PBIs. Copyright © 2013 Elsevier Inc. All rights reserved.

Breast Cancer Patients' Preferences for Adjuvant Radiotherapy Post Lumpectomy: Whole Breast Irradiation vs. Partial Breast Irradiation-Single Institutional Study.

PubMed

Bonin, Katija; McGuffin, Merrylee; Presutti, Roseanna; Harth, Tamara; Mesci, Aruz; Feldman-Stewart, Deb; Chow, Edward; Di Prospero, Lisa; Vesprini, Danny; Rakovitch, Eileen; Lee, Justin; Paszat, Lawrence; Doherty, Mary; Soliman, Hany; Ackerman, Ida; Cao, Xingshan; Kiss, Alex; Szumacher, Ewa

2018-02-01

This study was conducted to elucidate patients with early breast cancer preference for standard whole breast irradiation (WBI) or partial breast irradiation (PBI) following lumpectomy, as well as identify important factors for patients when making their treatment decisions. Based on relevant literature and ASTRO consensus statement guidelines, an educational tool and questionnaire were developed. Consenting, eligible women reviewed the educational tool and completed the trade-off questionnaire. Descriptive statistics were calculated, as well as chi-squares and a logistic regression model. Of the 90 patients who completed the study, 62 % preferred WBI, 30 % preferred PBI, 4 % required more information, and 3 % had no preferences. Of the patients who chose WBI, 58 % preferred hypofractionated RT, whereas 25 % preferred the conventional RT regimen. The majority of patients rated recurrence rate [WBI = 55/55 (100 %), PBI = 26/26 (100 %)] and survival [WBI = 54/55 (98 %), PBI = 26/26 (100 %)] as important factors contributing to their choice of treatment preference. Financial factors [WBI = 21/55 (38 %), PBI = 14/26 (53 %)] and convenience [WBI = 36/54 (67 %), PBI = 18/26 (69 %)] were rated as important less frequently. Significantly, more patients who preferred WBI also rated standard method of treatment as important when compared to patients who preferred PBI [WBI = 52/54 (96 %), PBI = 16/26 (61 %), χ 2  = 16.63, p = 0.001]. The majority of patients with early breast cancer who were surveyed for this study preferred WBI as an adjuvant treatment post lumpectomy, yet there was a sizeable minority who preferred PBI. This was associated with the importance patients place on standard treatment. These results will help medical professionals treat patients according to patient values.

Enhanced Performance of Perovskite CH3NH3PbI3 Solar Cell by Using CH3NH3I as Additive in Sequential Deposition.

PubMed

Xie, Yian; Shao, Feng; Wang, Yaoming; Xu, Tao; Wang, Deliang; Huang, Fuqiang

2015-06-17

Sequential deposition is a widely adopted method to prepare CH3NH3PbI3 on mesostructured TiO2 electrode for organic lead halide perovskite solar cells. However, this method often suffers from the uncontrollable crystal size, surface morphology, and residual PbI2 in the resulting CH3NH3PbI3, which are all detrimental to the device performance. We herein present an optimized sequential solution deposition method by introducing different amount of CH3NH3I in PbI2 precursor solution in the first step to prepare CH3NH3PbI3 absorber on mesoporous TiO2 substrates. The addition of CH3NH3I in PbI2 precursor solution can affect the crystallization and composition of PbI2 raw films, resulting in the variation of UV-vis absorption and surface morphology. Proper addition of CH3NH3I not only enhances the absorption but also improves the efficiency of CH3NH3PbI3 solar cells from 11.13% to 13.37%. Photoluminescence spectra suggest that the improvement of device performance is attributed to the decrease of recombination rate of carriers in CH3NH3PbI3 absorber. This current method provides a highly repeatable route for enhancing the efficiency of CH3NH3PbI3 solar cell in the sequential solution deposition method.

Test-retest reliability of the irrational performance beliefs inventory.

PubMed

Turner, M J; Slater, M J; Dixon, J; Miller, A

2018-02-01

The irrational performance beliefs inventory (iPBI) was developed to measure irrational beliefs within performance domains such as sport, academia, business, and the military. Past research indicates that the iPBI has good construct, concurrent, and predictive validity, but the test-retest reliability of the iPBI has not yet been examined. Therefore, in the present study the iPBI was administered to university sport and exercise students (n = 160) and academy soccer athletes (n = 75) at three-time points. Time point two occurred 7 days after time point one, and time point three occurred 21 days after time point two. In addition, social desirability was also measured. Repeated-measures MANCOVAs, intra-class coefficients, and Pearson's (r) correlations demonstrate that the iPBI has good test-retest reliability, with iPBI scores remaining stable across the three-time points. Pearson's correlation coefficients revealed no relationships between the iPBI and social desirability, indicating that the iPBI is not highly susceptible to response bias. The results are discussed with reference to the continued usage and development of the iPBI, and future research recommendations relating to the investigation of irrational performance beliefs are proposed.

Vanadium Redox Flow Batteries Using meta-Polybenzimidazole-Based Membranes of Different Thicknesses.

PubMed

Noh, Chanho; Jung, Mina; Henkensmeier, Dirk; Nam, Suk Woo; Kwon, Yongchai

2017-10-25

15, 25, and 35 μm thick meta-polybenzimidazole (PBI) membranes are doped with H 2 SO 4 and tested in a vanadium redox flow battery (VRFB). Their performances are compared with those of Nafion membranes. Immersed in 2 M H 2 SO 4 , PBI absorbs about 2 mol of H 2 SO 4 per mole of repeat unit. This results in low conductivity and low voltage efficiency (VE). In ex-situ tests, meta-PBI shows a negligible crossover of V 3+ and V 4+ ions, much lower than that of Nafion. This is due to electrostatic repulsive forces between vanadium cations and positively charged protonated PBI backbones, and the molecular sieving effect of PBI's nanosized pores. It turns out that charge efficiency (CE) of VRFBs using meta-PBI-based membranes is unaffected by or slightly increases with decreasing membrane thickness. Thick meta-PBI membranes require about 100 mV larger potentials to achieve the same charging current as thin meta-PBI membranes. This additional potential may increase side reactions or enable more vanadium ions to overcome the electrostatic energy barrier and to enter the membrane. On this basis, H 2 SO 4 -doped meta-PBI membranes should be thin to achieve high VE and CE. The energy efficiency of 15 μm thick PBI reaches 92%, exceeding that of Nafion 212 and 117 (N212 and N117) at 40 mA cm -2 .

Polymeric medium

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Jones, Michael G [Chubbuck, ID; Wertsching, Alan K [Idaho Falls, ID; Luther, Thomas A [Idaho Falls, ID; Trowbridge, Tammy L [Idaho Falls, ID

2012-03-06

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Polybenzimidazole compounds

DOEpatents

Klaehn, John R [Idaho Falls, ID; Peterson, Eric S [Idaho Falls, ID; Orme, Christopher J [Shelley, ID; Jones, Michael G [Chubbuck, ID; Wertsching, Alan K [Idaho Falls, ID; Luther, Thomas A [Idaho Falls, ID; Trowbridge, Tammy L [Idaho Falls, ID

2011-11-22

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Thin-Film Transformation of NH4 PbI3 to CH3 NH3 PbI3 Perovskite: A Methylamine-Induced Conversion-Healing Process.

PubMed

Zong, Yingxia; Zhou, Yuanyuan; Ju, Minggang; Garces, Hector F; Krause, Amanda R; Ji, Fuxiang; Cui, Guanglei; Zeng, Xiao Cheng; Padture, Nitin P; Pang, Shuping

2016-11-14

Methylamine-induced thin-film transformation at room-temperature is discovered, where a porous, rough, polycrystalline NH 4 PbI 3 non-perovskite thin film converts stepwise into a dense, ultrasmooth, textured CH 3 NH 3 PbI 3 perovskite thin film. Owing to the beneficial phase/structural development of the thin film, its photovoltaic properties undergo dramatic enhancement during this NH 4 PbI 3 -to-CH 3 NH 3 PbI 3 transformation process. The chemical origins of this transformation are studied at various length scales. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Polybenzimidazole compounds, polymeric media, and methods of post-polymerization modifications

DOEpatents

Klaehn, John R.; Peterson, Eric S.; Orme, Christopher J.; Jones, Michael G.; Wertsching, Alan K.; Luther, Thomas A.; Trowbridge, Tammy L.

2007-12-18

A PBI compound includes imidazole nitrogens at least a portion of which are substituted with a moiety containing a carbonyl group, the substituted imidazole nitrogens being bonded to carbon of the carbonyl group. At least 85% of the nitrogens may be substituted. The carbonyl-containing moiety may include RCO--, where R is alkoxy or haloalkyl. The PBI compound may exhibit a first temperature marking an onset of weight loss corresponding to reversion of the substituted PBI that is less than a second temperature marking an onset of decomposition of an otherwise identical PBI compound without the substituted moiety. The PBI compound may be included in separatory media. A substituted PBI synthesis method may include providing a parent PBI in a less than 5 wt % solvent solution. Substituting may use more than 5 equivalents in relation to the imidazole nitrogens to be substituted.

Optical and Atomic Force Microscopy Characterization of PbI2 Quantum Dots

NASA Technical Reports Server (NTRS)

Mu, R.; Tung, Y. S.; Ueda, A.; Henderson, D. O.

1997-01-01

Lead iodide (PbI2) clusters were synthesized from the chemical reaction of NaI (or KI) with Pb(NO3)2 in H2O, D2O, CH3OH, and C3H7OH media. The observation of the absorption features above 350 nm with the help of integrating sphere accessory strongly suggests the quantum dot formation of PbI2 in solution. Spectral comparison between the synthesized PbI2 clusters in solution and PbI2 nanophase by impregnation of PbI2 in four different pore-sized porous silica indicates that the PbI2 cluster size in solution is less than 2.5 nm in lateral dimension. Atomic force microscopy (AFM) measurements show that the PbL clusters deposited onto three different molecularly flat surfaces are single-layered. The measured height is 1.0 - 0.1 nm. The swollen layer thickness can be attributed to the intralayer contraction from the strong lateral interaction among PbI2 molecules, which is supported by ab initio calculation. Raman scattering measurement of LO and TO modes of PbI2 in bulk and in the confined state were also conducted in 50-150 cu cm region. The observed three bands at 74, %, 106 1/cm are assigned to TO2, LO2, and LO, mode, respectively. The relatively small red-shift in LO modes may be caused by the surface phonon polaritons of PbI2 nanophase in the porous silica.

Deep subcortical infarct burden in relation to apolipoprotein B/AI ratio in patients with intracranial atherosclerotic stenosis.

PubMed

Park, J-H; Hong, K-S; Lee, J; Kim, Y-J; Song, P

2013-04-01

Pre-existing brain infarct (PBI), frequently seen on magnetic resonance imaging and usually silent, is recognized as a risk factor for future stroke. Increased apolipoprotein B (apoB)/apoAI ratio is known to be a risk predictor of ischaemic stroke and is associated with intracranial atherosclerotic stenosis (ICAS). However, little is known about the association of apoB/apoAI ratio with PBI. A total of 522 statin-/fibrate-naïve Korean patients, who experienced acute ischaemic stroke, were categorized into three groups: ICAS (n=254), extracranial (n=51), and no cerebral atherosclerotic stenosis (n=217). We explored the association between apoB/apoAI ratio and PBI lesions according to atherosclerosis type (ICAS, ECAS, and NCAS), PBI location (deep subcortical [ds-PBI] versus hemispheric [h-PBI]), and symptomatic PBI (s-PBI) which was relevant to a prior clinical stroke event. Pre-existing brain infarct(+) patients showed a higher apoB/apoAI ratio than PBI(-) patients (0.81 ± 0.28 vs. 0.72 ± 0.23, P<0.001). In ICAS group, patients with higher apoB/apoAI ratio quartiles had more PBIs, ds-PBIs, and s-PBIs (P=0.020, P=0.025, and P=0.001, respectively). With multivariable analyses, the highest apoB/apoAI ratio quartile was associated with PBI (OR, 2.56; 95% CI, 1.39-4.73), ds-PBI (2.48; 1.33-4.62), and advanced (≥ 3) ds-PBIs (2.68; 1.27-5.63) in ICAS group, but not with h-PBI. s-PBI had a dose-response relationship with apoB/apoAI ratio quartiles (6.18; 1.31-29.13 for the second; 5.34; 1.06-26.83 for the third; and 12.17; 2.50-59.19 for the fourth quartile), when referenced to the first quartile. ApoB/apoAI ratio is associated with asymptomatic deep subcortical ischaemic burden as well as with symptomatic lesion in patients with ICAS. © 2012 The Author(s) European Journal of Neurology © 2012 EFNS.

Control of PbI2 nucleation and crystallization: towards efficient perovskite solar cells based on vapor-assisted solution process

NASA Astrophysics Data System (ADS)

Yang, Chongqiu; Peng, Yanke; Simon, Terrence; Cui, Tianhong

2018-04-01

Perovskite solar cells (PSC) have outstanding potential to be low-cost, high-efficiency photovoltaic devices. The PSC can be fabricated by numerous techniques; however, the power conversion efficiency (PCE) for the two-step-processed PSC falls behind that of the one-step method. In this work, we investigate the effects of relative humidity (RH) and dry air flow on the lead iodide (PbI2) solution deposition process. We conclude that the quality of the PbI2 film is critical to the development of the perovskite film and the performance of the PSC device. Low RH and dry air flow used during the PbI2 spin coating procedure can increase supersaturation concentration to form denser PbI2 nuclei and a more suitable PbI2 film. Moreover, airflow-assisted PbI2 drying and thermal annealing steps can smooth transformation from the nucleation stage to the crystallization stage.

Improved perovskite morphology and crystallinity using porous PbI2 layers for efficient planar heterojunction solar cells

NASA Astrophysics Data System (ADS)

Jia, Xianyu; Hu, Ziyang; Xu, Jie; Huang, Like; Zhang, Jing; Zhang, Jianjun; Zhu, Yuejin

2017-12-01

We demonstrate the flexible and facile use of porous PbI2 layers to fabricate high quality perovskite films with a dense surface and without residual PbI2. PbI2 precursor solutions by adding polystyrene pore-forming agents are first spin-coated to fabricate the wet film. A porous PbI2 layer is formed by washing off polystyrene using organic solvents. The porous PbI2 layer not only serves as a channel for transporting the CH3NH3I solution but also offers extremely enlarged contact areas, facilitating interfacial reaction with CH3NH3I. Shiny smooth perovskite films with excellent electronic quality and solar cells with an efficiency up to 17% are obtained.

Fabrication of CH3NH3PbI3/PVP Composite Fibers via Electrospinning and Deposition

PubMed Central

Chao, Li-Min; Tai, Ting-Yu; Chen, Yueh-Ying; Lin, Pei-Ying; Fu, Yaw-Shyan

2015-01-01

In our study, one-dimensional PbI2/polyvinylpyrrolidone (PVP) composition fibers have been prepared by using PbI2 and PVP as precursors dissolved in N,N-dimethylformamide via a electrospinning process. Dipping the fibers into CH3NH3I solution changed its color, indicating the formation of CH3NH3PbI3, to obtain CH3NH3PbI3/PVP composite fibers. The structure, morphology and composition of the all as-prepared fibers were characterized by using X-ray diffraction and scanning electron microscopy. PMID:28793517

Acid and alkali doped PBI electrolyte in electrochemical system

NASA Astrophysics Data System (ADS)

Xing, Baozhong

In this work the conductivity of blank PBI membrane, acid doped PBI and alkaline doped PBI was systematically studied. A new methodology for sorption kinetics study in electrolyte solution has been established by monitoring the conductivity change during the sorption process. The model of the doping process and mechanism of conductivity are proposed. The performance of PBI (doped under optimum conditions) in fuel cell as PEM was evaluated. The experimental results show that the blank PBI in acid solution is an ionic insulator. It clarified the long time confusion in this area. The acid doped PBI membrane is an ionic conductor. The conductivity increases with the concentration of the acid solution. In high concentration acid solution, the conductivity increases with the type of acid in the order: H2SO 4 > H3PO4 > HClO4 > HNO3 > HCl. The kinetics of the doping process was studied, by a continuous method. The ionic conductivity mechanism was established. The PBI membranes doped with H2SO4 and H3PO4 exhibit better performance than NafionRTM. The doped FBI has more resistance to CO poison. 3% CO in H2 has little effect on the H3PO 4 doped PBI membrane at 185°C. The conductivity of the alkali doped PBI membrane changes with the concentration of the alkaline solution and the type of the alkalis. The conductivity has a maximum in KOH and NaOH solution. The maximum conductivity in KOH is higher than in NaOH and LiOH. It is about 5 times of that of NafionRTM in alkaline solution. The two-step sorption process in alkaline solution was observed. The first step is the permeation process of the alkalis in the PBI membrane. The permeation is the results of diffusion and interaction. It is concluded that the permeation process is controlled by the rate of interaction between the alkali and PBI molecule. The second step is the relaxation process in the membrane. This step contributes more to the conductivity for the membrane than the first step. The ionic conductivity mechanism was established. In solution the cations and OH- all participate in the transport of current. It is the OH- that breaks the bonds between PBI molecules and enables the cations pass through the membrane. The performance of alkali doped PBI (doped under optimum conditions) in fuel cell as PEM is as good as NafionRTM.

Structure-activity relationships in cytotoxic Au(I)/Au(III) complexes derived from 2-(2'-pyridyl)benzimidazole.

PubMed

Maiore, Laura; Aragoni, Maria Carla; Deiana, Carlo; Cinellu, Maria Agostina; Isaia, Francesco; Lippolis, Vito; Pintus, Anna; Serratrice, Maria; Arca, Massimiliano

2014-04-21

Gold(I) and gold(III) complexes derived from 2-(2'-pyridyl)benzimidazole (pbiH) were proven to be a promising class of in vitro antitumor agents against A2780 human ovarian cancer cells. In this paper, a comparative electrochemical, UV-vis absorption, and emission spectroscopic investigation is reported on pbiH, the two mononuclear Au(III) complexes [(pbi)AuX2] (X = Cl (1), AcO (2)), the four mononuclear Au(I) derivatives [(pbiH)AuCl] (3), [(pbiH)Au(PPh3)]PF6 ((4(+))(PF6(-))), [(pbi)Au(PPh3)] (5), and [(pbi)Au(TPA)] (6), the three mixed-valence Au(III)/Au(I) complexes [(μ-pbi)Au2Cl3] (7), [(Ph3P)Au(μ-pbi)AuX2]PF6 (X = Cl ((8(+))(PF6(-))), AcO ((9(+))(PF6(-)))), and the binuclear Au(I)-Au(I) compound [(μ-pbi)Au2(PPh3)2]PF6 ((10(+))(PF6(-))). All complexes feature irreversible reduction processes related to the Au(III)/Au(I) or Au(I)/Au(0) processes and peculiar luminescent emission at about 360-370 nm in CH2Cl2, with quantum yields that are remarkably lower ((0.7-14.5) × 10(-2)) in comparison to that determined for the free pbiH ligand (31.5 × 10(-2)) in the same solvent. The spectroscopic and electrochemical properties of all complexes were interpreted on the grounds of time-dependent PBE0/DFT calculations carried out both in the gas phase and in CH2Cl2 implicitly considered within the IEF-PCM SCRF approach. The electronic structure of the complexes, and in particular the energy and composition of the Kohn-Sham LUMOs, can be related to the antiproliferative properties against the A2780 ovarian carcinoma cell line, providing sound quantitative structure-activity relationships and shedding a light on the role played by the global charge and nature of ancillary ligands in the effectiveness of Au-based antitumor drugs.

Polybenzimidazole block copolymers for fuel cell: synthesis and studies of block length effects on nanophase separation, mechanical properties, and proton conductivity of PEM.

PubMed

Maity, Sudhangshu; Jana, Tushar

2014-05-14

A series of meta-polybenzimidazole-block-para-polybenzimidazole (m-PBI-b-p-PBI), segmented block copolymers of PBI, were synthesized with various structural motifs and block lengths by condensing the diamine terminated meta-PBI (m-PBI-Am) and acid terminated para-PBI (p-PBI-Ac) oligomers. NMR studies and existence of two distinct glass transition temperatures (Tg), obtained from dynamical mechanical analysis (DMA) results, unequivocally confirmed the formation of block copolymer structure through the current polymerization methodology. Appropriate and careful selection of oligomers chain length enabled us to tailor the block length of block copolymers and also to make varieties of structural motifs. Increasingly distinct Tg peaks with higher block length of segmented block structure attributed the decrease in phase mixing between the meta-PBI and para-PBI blocks, which in turn resulted into nanophase segregated domains. The proton conductivities of proton exchange membrane (PEM) developed from phosphoric acid (PA) doped block copolymer membranes were found to be increasing substantially with increasing block length of copolymers even though PA loading of these membranes did not alter appreciably with varying block length. For example when molecular weight (Mn) of blocks were increased from 1000 to 5500 then the proton conductivities at 160 °C of resulting copolymers increased from 0.05 to 0.11 S/cm. Higher block length induced nanophase separation between the blocks by creating less morphological barrier within the block which facilitated the movement of the proton in the block and hence resulting higher proton conductivity of the PEM. The structural varieties also influenced the phase separation and proton conductivity. In comparison to meta-para random copolymers reported earlier, the current meta-para segmented block copolymers were found to be more suitable for PBI-based PEM.

Synthesis, structural, thermal and optical studies of inorganic-organic hybrid semiconductors, R-PbI4

NASA Astrophysics Data System (ADS)

Pradeesh, K.; Nageswara Rao, K.; Vijaya Prakash, G.

2013-02-01

Wide varieties of naturally self-assembled two-dimensional inorganic-organic (IO) hybrid semiconductors, (4-ClC6H4NH3)2PbI4, (C6H9C2H4NH3)2PbI4, (CnH2n+1NH3)2PbI4 (where n = 12, 16, 18), (CnH2n-1NH3)2PbI4 (where n = 3, 4, 5), (C6H5C2H4NH3)2PbI4, NH3(CH2)12NH3PbI4, and (C4H3SC2H4NH3)2PbI4, were fabricated by intercalating structurally diverse organic guest moieties into lead iodide perovskite structure. The crystal packing of all these fabricated IO-hybrids comprises of well-ordered organic and inorganic layers, stacked-up alternately along c-axis. Almost all these hybrids are thermally stable upto 200 °C and show strong room-temperature exciton absorption and photoluminescence features. These strongly confined optical excitons are highly influenced by structural deformation of PbI matrix due to the conformation of organic moiety. A systematic correlation of optical exciton behavior of IO-hybrids with the organic/inorganic layer thicknesses, intercalating organic moieties, and various structural disorders were discussed. This systematic study clearly suggests that the PbI layer crumpling is directly responsible for the tunability of optical exciton energy.

High-efficiency perovskite solar cells based on the black polymorph of HC(NH2)2 PbI3.

PubMed

Lee, Jin-Wook; Seol, Dong-Jin; Cho, An-Na; Park, Nam-Gyu

2014-08-06

Perovskite solar cells with power conversion efficiencies exceeding 16% at AM 1.5 G one sun illumination are developed using the black polymorph of formamidnium lead iodide, HC(NH2)2 PbI3 . Compared with CH3 NH3 PbI3 , HC(NH2 )2 PbI3 extends its absoprtion to 840 nm and shows no phase transition between 296 and 423 K. Moreover, a solar cell based on HC(NH2 )2 PbI3 exhibits photostability and little I-V hysteresis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

On the growth of CH3NH3PbI3-xClx single crystal and characterization

NASA Astrophysics Data System (ADS)

Su, J.; Wang, W. F.; Lei, Y.; Zhang, L.; Xu, L. H.; Wang, D.; Lu, D.; Bai, Y.

2018-05-01

In this paper, CH3NH3PbI3-xClx crystal was grown by solution cooling method with CH3NH3I and PbCl2 as raw materials. Lead compounds and CH3NH3PbI3-xClx crystal with size about 6 mm × 4 mm × 2 mm were obtained. The chemical reactions with different CH3NH3I/PbCl2 ratios were analyzed. XPS shows the content of chlorine in CH3NH3PbI3-xClx is about 0.91%. PXRD, FT-IR, Raman and absorbance spectra were used to study the structure and optical properties of CH3NH3PbI3-xClx by comparing with CH3NH3PbI3 crystal. The CH3NH3PbI3-xClx crystal grown is of tetragonal structure with the lattice constants a = b = 8.8165 Å, c = 12.7920 Å and the bandgap value of 1.57 eV.

Exciton versus free carrier photogeneration in organometal trihalide perovskites probed by broadband ultrafast polarization memory dynamics.

PubMed

Sheng, ChuanXiang; Zhang, Chuang; Zhai, Yaxin; Mielczarek, Kamil; Wang, Weiwei; Ma, Wanli; Zakhidov, Anvar; Vardeny, Z Valy

2015-03-20

We studied the ultrafast transient response of photoexcitations in two hybrid organic-inorganic perovskite films used for high efficiency photovoltaic cells, namely, CH(3)NH(3)PbI(3) and CH(3)NH(3)PbI(1.1)Br(1.9) using polarized broadband pump-probe spectroscopy in the spectral range of 0.3-2.7 eV with 300 fs time resolution. For CH(3)NH(3)PbI(3) with above-gap excitation we found both photogenerated carriers and excitons, but only carriers are photogenerated with below-gap excitation. In contrast, mainly excitons are photogenerated in CH(3)NH(3)PbI(1.1)Br(1.9). Surprisingly, we also discovered in CH(3)NH(3)PbI(3), but not in CH(3)NH(3)PbI(1.1)Br(1.9), transient photoinduced polarization memory for both excitons and photocarriers, which is also reflected in the steady state photoluminescence. From the polarization memory dynamics we obtained the excitons diffusion constant in CH(3)NH(3)PbI(3), D≈0.01  cm(2) s(-1).

Exciton versus Free Carrier Photogeneration in Organometal Trihalide Perovskites Probed by Broadband Ultrafast Polarization Memory Dynamics

NASA Astrophysics Data System (ADS)

Sheng, ChuanXiang; Zhang, Chuang; Zhai, Yaxin; Mielczarek, Kamil; Wang, Weiwei; Ma, Wanli; Zakhidov, Anvar; Vardeny, Z. Valy

2015-03-01

We studied the ultrafast transient response of photoexcitations in two hybrid organic-inorganic perovskite films used for high efficiency photovoltaic cells, namely, CH3NH3PbI3 and CH3NH3PbI1.1Br1.9 using polarized broadband pump-probe spectroscopy in the spectral range of 0.3-2.7 eV with 300 fs time resolution. For CH3NH3PbI3 with above-gap excitation we found both photogenerated carriers and excitons, but only carriers are photogenerated with below-gap excitation. In contrast, mainly excitons are photogenerated in CH3NH3PbI1.1Br1.9 . Surprisingly, we also discovered in CH3NH3PbI3 , but not in CH3NH3PbI1.1Br1.9 , transient photoinduced polarization memory for both excitons and photocarriers, which is also reflected in the steady state photoluminescence. From the polarization memory dynamics we obtained the excitons diffusion constant in CH3NH3PbI3 , D ≈0.01 cm2 s-1 .

Insight into the CH3NH3PbI3/C interface in hole-conductor-free mesoscopic perovskite solar cells

NASA Astrophysics Data System (ADS)

Li, Jiangwei; Niu, Guangda; Li, Wenzhe; Cao, Kun; Wang, Mingkui; Wang, Liduo

2016-07-01

Perovskite solar cells (PSCs) with hole-conductor-free mesoscopic architecture have shown superb stability and great potential in practical application. The printable carbon counter electrodes take full responsibility of extracting holes from the active CH3NH3PbI3 absorbers. However, an in depth study of the CH3NH3PbI3/C interface properties, such as the structural formation process and the effect of interfacial conditions on hole extraction, is still lacking. Herein, we present, for the first time, an insight into the spatial confinement induced CH3NH3PbI3/C interface formation by in situ photoluminescence observations during the crystallization process of CH3NH3PbI3. The derived reaction kinetics allows a quantitative description of the perovskite formation process. In addition, we found that the interfacial contact between carbon and perovskite was dominant for hole extraction efficiency and associated with the photovoltaic parameter of short circuit current density (JSC). Consequently, we conducted a solvent vapor assisted process of PbI2 diffusion to carefully control the CH3NH3PbI3/C interface with less unreacted PbI2 barrier. The improvement of interface conditions thereby contributes to a high hole extraction proved by the charge extraction resistance and PL lifetime change, resulting in the increased JSC valve.Perovskite solar cells (PSCs) with hole-conductor-free mesoscopic architecture have shown superb stability and great potential in practical application. The printable carbon counter electrodes take full responsibility of extracting holes from the active CH3NH3PbI3 absorbers. However, an in depth study of the CH3NH3PbI3/C interface properties, such as the structural formation process and the effect of interfacial conditions on hole extraction, is still lacking. Herein, we present, for the first time, an insight into the spatial confinement induced CH3NH3PbI3/C interface formation by in situ photoluminescence observations during the crystallization process of CH3NH3PbI3. The derived reaction kinetics allows a quantitative description of the perovskite formation process. In addition, we found that the interfacial contact between carbon and perovskite was dominant for hole extraction efficiency and associated with the photovoltaic parameter of short circuit current density (JSC). Consequently, we conducted a solvent vapor assisted process of PbI2 diffusion to carefully control the CH3NH3PbI3/C interface with less unreacted PbI2 barrier. The improvement of interface conditions thereby contributes to a high hole extraction proved by the charge extraction resistance and PL lifetime change, resulting in the increased JSC valve. Electronic supplementary information (ESI) available: Fig. S1-S11, Tables S1, S2 and details of the Avrami model for reaction kinetics. See DOI: 10.1039/c6nr03359h

Ultrasound-Based Guidance for Partial Breast Irradiation Therapy

DTIC Science & Technology

2011-01-01

and also are inexpensive. b. Collect US data from patient before the PBI treatment at the same time that CT is collected (months 2-14). We...introduces minimal divergence from the original workflow of PBI treatment. We have an approved institutional review board (IRB) protocol to obtain B...irradiation of only the in- volved area of the breast, partial breast irradiation ( PBI ), is as effective as whole breast irradiation [1]. Benefits of PBI

Surface supported gold-organic hybrids: on-surface synthesis and surface directed orientation.

PubMed

Zhang, Haiming; Franke, Jörn-Holger; Zhong, Dingyong; Li, Yan; Timmer, Alexander; Arado, Oscar Díaz; Mönig, Harry; Wang, Hong; Chi, Lifeng; Wang, Zhaohui; Müllen, Klaus; Fuchs, Harald

2014-04-09

The surface-assisted synthesis of gold-organic hybrids on Au (111) and Au (100) surfaces is repotred by thermally initiated dehalogenation of chloro-substituted perylene-3,4,9,10-tetracarboxylic acid bisimides (PBIs). Structures and surface-directed alignment of the Au-PBI chains are investigated by scanning tunnelling microscopy in ultra high vacuum conditions. Using dichloro-PBI as a model system, the mechanism for the formation of Au-PBI dimer is revealed with scanning tunnelling microscopy studies and density functional theory calculations. A PBI radical generated from the homolytic C-Cl bond dissociation can covalently bind a surface gold atom and partially pull it out of the surface to form stable PBI-Au hybrid species, which also gives rise to the surface-directed alignment of the Au-PBI chains on reconstructed Au (100) surfaces. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Building 9 ISS mock-ups and trainers

NASA Image and Video Library

1999-08-02

Photographic documentation showing the bldg. 9 ISS module mock-ups and trainers. Views include: various overall views of the configuration of the ISS module trainers on the floor of bldg. 9 (08445-46, 08449-51, 08458-61, 08464-65, 08469, 08471, 08476); various portions of the mock-ups (08447-48, 08470); views of the Node 2, Experiment Module and Logistics Module (08452); Node 2 (08453, 08466); Destiny and Node 2 (08454); Destiny, Unity and Airlock (08455); Zarya, Service Module and shuttle mock-ups (08456); Logistics Module and Experiment Module (08457, 08468); various views of Columbia, Node 2 and Destiny (08462-63); Columbus, Node 2, Experiment Module and Logistics Module (08467); U.S. Laboratory module (08472); Logistics Module (08473); module layout (08474); Logistics Module and Experiment Module (08475).

Screening Libraries of Semifluorinated Arylene Bisimides to Discover and Predict Thermodynamically Controlled Helical Crystallization.

PubMed

Ho, Ming-Shou; Partridge, Benjamin E; Sun, Hao-Jan; Sahoo, Dipankar; Leowanawat, Pawaret; Peterca, Mihai; Graf, Robert; Spiess, Hans W; Zeng, Xiangbing; Ungar, Goran; Heiney, Paul A; Hsu, Chain-Shu; Percec, Virgil

2016-12-12

Synthesis, structural, and retrostructural analysis of a library containing 16 self-assembling perylene (PBI), 1,6,7,12-tetrachloroperylene (Cl 4 PBI), naphthalene (NBI), and pyromellitic (PMBI) bisimides functionalized with environmentally friendly AB 3 chiral racemic semifluorinated minidendrons at their imide groups via m = 0, 1, 2, and 3 methylene units is reported. These semifluorinated compounds melt at lower temperatures than homologous hydrogenated compounds, permitting screening of all their thermotropic phases via structural analysis to discover thermodynamically controlled helical crystallization from propeller-like, cogwheel, and tilted molecules as well as lamellar-like structures. Thermodynamically controlled helical crystallization was discovered for propeller-like PBI, Cl 4 PBI and NBI with m = 0. Unexpectedly, assemblies of twisted Cl 4 PBIs exhibit higher order than those of planar PBIs. PBI with m = 1, 2, and 3 form a thermodynamically controlled columnar hexagonal 2D lattice of tilted helical columns with intracolumnar order. PBI and Cl 4 PBI with m = 1 crystallize via a recently discovered helical cogwheel mechanism, while NBI and PMBI with m = 1 form tilted helical columns. PBI, NBI and PMBI with m = 2 generate lamellar-like structures. 3D and 2D assemblies of PBI with m = 1, 2, and 3, NBI with m = 1 and PMBI with m = 2 exhibit 3.4 Å π-π stacking. The library approach applied here and in previous work enabled the discovery of six assemblies which self-organize via thermodynamic control into 3D and 2D periodic arrays, and provides molecular principles to predict the supramolecular structure of electronically active components.

Management of penetrating brain injury

PubMed Central

Kazim, Syed Faraz; Shamim, Muhammad Shahzad; Tahir, Muhammad Zubair; Enam, Syed Ather; Waheed, Shahan

2011-01-01

Penetrating brain injury (PBI), though less prevalent than closed head trauma, carries a worse prognosis. The publication of Guidelines for the Management of Penetrating Brain Injury in 2001, attempted to standardize the management of PBI. This paper provides a precise and updated account of the medical and surgical management of these unique injuries which still present a significant challenge to practicing neurosurgeons worldwide. The management algorithms presented in this document are based on Guidelines for the Management of Penetrating Brain Injury and the recommendations are from literature published after 2001. Optimum management of PBI requires adequate comprehension of mechanism and pathophysiology of injury. Based on current evidence, we recommend computed tomography scanning as the neuroradiologic modality of choice for PBI patients. Cerebral angiography is recommended in patients with PBI, where there is a high suspicion of vascular injury. It is still debatable whether craniectomy or craniotomy is the best approach in PBI patients. The recent trend is toward a less aggressive debridement of deep-seated bone and missile fragments and a more aggressive antibiotic prophylaxis in an effort to improve outcomes. Cerebrospinal fluid (CSF) leaks are common in PBI patients and surgical correction is recommended for those which do not close spontaneously or are refractory to CSF diversion through a ventricular or lumbar drain. The risk of post-traumatic epilepsy after PBI is high, and therefore, the use of prophylactic anticonvulsants is recommended. Advanced age, suicide attempts, associated coagulopathy, Glasgow coma scale score of 3 with bilaterally fixed and dilated pupils, and high initial intracranial pressure have been correlated with worse outcomes in PBI patients. PMID:21887033

Preparation for foam composites. [using polybenzimidazole for fireproofing panels

NASA Technical Reports Server (NTRS)

Maximovich, M. G.

1974-01-01

Methods were developed for the fabrication of fire resistant panels utilizing polybenzimidazole (PBI) and Kerimid 601 resins along with glass, quartz, and Kevlar reinforcements. Stitched truss structure, both unfilled and filled with PBI foam, were successfully fabricated and tested. Second generation structures were then selected, fabricated, and tested, with a PBI/glass skin/PBI foam sandwich structure emerging as the optimum panel concept. Mechanical properties, smoke generation, and fire resistance were determined for the candidate panels.

Validation of the Malay Version of the Parental Bonding Instrument among Malaysian Youths Using Exploratory Factor Analysis.

PubMed

Muhammad, Noor Azimah; Shamsuddin, Khadijah; Omar, Khairani; Shah, Shamsul Azhar; Mohd Amin, Rahmah

2014-01-01

Parenting behaviour is culturally sensitive. The aims of this study were (1) to translate the Parental Bonding Instrument into Malay (PBI-M) and (2) to determine its factorial structure and validity among the Malaysian population. The PBI-M was generated from a standard translation process and comprehension testing. The validation study of the PBI-M was administered to 248 college students aged 18 to 22 years. Participants in the comprehension testing had difficulty understanding negative items. Five translated double negative items were replaced with five positive items with similar meanings. Exploratory factor analysis showed a three-factor model for the PBI-M with acceptable reliability. Four negative items (items 3, 4, 8, and 16) and item 19 were omitted from the final PBI-M list because of incorrect placement or low factor loading (< 0.32). Out of the final 20 items of the PBI-M, there were 10 items for the care factor, five items for the autonomy factor and five items for the overprotection factor. All the items loaded positively on their respective factors. The Malaysian population favoured positive items in answering questions. The PBI-M confirmed the three-factor model that consisted of care, autonomy and overprotection. The PBI-M is a valid and reliable instrument to assess the Malaysian parenting style. Confirmatory factor analysis may further support this finding. Malaysia, parenting, questionnaire, validity.

Post-boosting of classification boundary for imbalanced data using geometric mean.

PubMed

Du, Jie; Vong, Chi-Man; Pun, Chi-Man; Wong, Pak-Kin; Ip, Weng-Fai

2017-12-01

In this paper, a novel imbalance learning method for binary classes is proposed, named as Post-Boosting of classification boundary for Imbalanced data (PBI), which can significantly improve the performance of any trained neural networks (NN) classification boundary. The procedure of PBI simply consists of two steps: an (imbalanced) NN learning method is first applied to produce a classification boundary, which is then adjusted by PBI under the geometric mean (G-mean). For data imbalance, the geometric mean of the accuracies of both minority and majority classes is considered, that is statistically more suitable than the common metric accuracy. PBI also has the following advantages over traditional imbalance methods: (i) PBI can significantly improve the classification accuracy on minority class while improving or keeping that on majority class as well; (ii) PBI is suitable for large data even with high imbalance ratio (up to 0.001). For evaluation of (i), a new metric called Majority loss/Minority advance ratio (MMR) is proposed that evaluates the loss ratio of majority class to minority class. Experiments have been conducted for PBI and several imbalance learning methods over benchmark datasets of different sizes, different imbalance ratios, and different dimensionalities. By analyzing the experimental results, PBI is shown to outperform other imbalance learning methods on almost all datasets. Copyright © 2017 Elsevier Ltd. All rights reserved.

Insight into the CH3NH3PbI3/C interface in hole-conductor-free mesoscopic perovskite solar cells.

PubMed

Li, Jiangwei; Niu, Guangda; Li, Wenzhe; Cao, Kun; Wang, Mingkui; Wang, Liduo

2016-08-07

Perovskite solar cells (PSCs) with hole-conductor-free mesoscopic architecture have shown superb stability and great potential in practical application. The printable carbon counter electrodes take full responsibility of extracting holes from the active CH3NH3PbI3 absorbers. However, an in depth study of the CH3NH3PbI3/C interface properties, such as the structural formation process and the effect of interfacial conditions on hole extraction, is still lacking. Herein, we present, for the first time, an insight into the spatial confinement induced CH3NH3PbI3/C interface formation by in situ photoluminescence observations during the crystallization process of CH3NH3PbI3. The derived reaction kinetics allows a quantitative description of the perovskite formation process. In addition, we found that the interfacial contact between carbon and perovskite was dominant for hole extraction efficiency and associated with the photovoltaic parameter of short circuit current density (JSC). Consequently, we conducted a solvent vapor assisted process of PbI2 diffusion to carefully control the CH3NH3PbI3/C interface with less unreacted PbI2 barrier. The improvement of interface conditions thereby contributes to a high hole extraction proved by the charge extraction resistance and PL lifetime change, resulting in the increased JSC valve.

High-performance air-stable n-channel organic thin film transistors based on halogenated perylene bisimide semiconductors.

PubMed

Schmidt, Rüdiger; Oh, Joon Hak; Sun, Ya-Sen; Deppisch, Manuela; Krause, Ana-Maria; Radacki, Krzysztof; Braunschweig, Holger; Könemann, Martin; Erk, Peter; Bao, Zhenan; Würthner, Frank

2009-05-06

The syntheses and comprehensive characterization of 14 organic semiconductors based on perylene bisimide (PBI) dyes that are equipped with up to four halogen substituents in the bay area of the perylene core and five different highly fluorinated imide substituents are described. The influence of the substituents on the LUMO level and the solid state packing of PBIs was examined by cyclic voltammetry and single crystal structure analyses of seven PBI derivatives, respectively. Top-contact/bottom-gate organic thin film transistor (OTFT) devices were constructed by vacuum deposition of these PBIs on SiO(2) gate dielectrics that had been pretreated with n-octadecyl triethoxysilane in vapor phase (OTS-V) or solution phase (OTS-S). The electrical characterization of all devices was accomplished in a nitrogen atmosphere as well as in air, and the structural features of thin films were explored by grazing incidence X-ray diffraction (GIXD) and atomic force microscopy (AFM). Several of those PBIs that bear only hydrogen or up to two fluorine substitutents at the concomitantly flat PBI core afforded excellent n-channel transistors, in particular, on OTS-S substrate and even in air (mu > 0.5 cm(2) V(-1) s(-1); I(on)/I(off) > 10(6)). The best OTFTs were obtained for 2,2,3,3,4,4,4-heptafluorobutyl-substituted PBI 1a ("PTCDI-C4F7") on OTS-S with n-channel field effect mobilities consistently >1 cm(2) V(-1) s(-1) and on-to-off current rations of 10(6) in a nitrogen atmosphere and in air. For distorted core-tetrahalogenated (fluorine, chlorine, or bromine) PBIs, less advantageous solid state packing properties were found and high performance OTFTs were obtained from only one tetrachlorinated derivative (2d on OTS-S). The excellent on-to-off current modulation combined with high mobility in air makes these PBIs suitable for a wide range of practical applications.

Unraveling surface and bulk trap states in lead halide perovskite solar cells using impedance spectroscopy

NASA Astrophysics Data System (ADS)

Han, Changfeng; Wang, Kai; Zhu, Xixiang; Yu, Haomiao; Sun, Xiaojuan; Yang, Qin; Hu, Bin

2018-03-01

Organic-inorganic hybrid perovskites (OIHPs) have been widely recognized as an excellent candidate for next-generation photovoltaic materials because of their highly efficient power conversion. Acquiring a complete understanding of trap states and dielectric properties in OIHP-based solar cells at the steady state is highly desirable in order to further explore and improve their optoelectronic functionalities and properties. We report CH3NH3PbI3-x Cl x -based planar solar cells with a power conversion efficiency (PCE) of 15.8%. The illumination intensity dependence of the current density-voltage (J-V) revealed the presence of trap-assisted recombination at low fluences. Non-destructive ac impedance spectroscopy (ac-IS) was applied to characterize the device at the steady state. The capacitance-voltage (C-V) spectra exhibited some distinct variations at a wide range of ac modulation frequencies with and without photo-excitations. Since the frequency-dependent chemical capacitance ({{C}μ }) is concerned with the surface and bulk related density of states (DOS) in CH3NH3PbI3-x Cl x , we verified this by fitting the corresponding DOS by a Gaussian distribution function. We ascertained that the electronic sub-gap trap states present in the solution processed CH3NH3PbI3-x Cl x and their distribution differs from the surface to the bulk. In fact, we demonstrated that both surfaces that were adjacent to the electron and hole transport layers featured analogous DOS. Despite this, photo- and bias-induced giant dielectric responses (i.e. both real and imaginary parts) were detected. A remarkable reduction of {{C}μ } at higher frequencies (i.e. more than 100 kHz) was ascribed to the effect of dielectric loss in CH3NH3PbI3-x Cl x .

Photoelectric characteristics of CH3NH3PbI3/p-Si heterojunction

NASA Astrophysics Data System (ADS)

Yamei, Wu; Ruixia, Yang; Hanmin, Tian; Shuai, Chen

2016-05-01

Organic-inorganic hybrid perovskite CH3NH3PbI3 film is prepared on p-type silicon substrate using the one-step solution method to form a CH3NH3PbI3/p-Si heterojunction. The film morphology and structure are characterized by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The photoelectric properties of the CH3NH3PbI3/p-Si heterojunction are studied by testing the current-voltage (I-V) with and without illumination and capacitance-voltage (C-V) characteristics. It turns out from the I-V curve without illumination that the CH3NH3PbI3/p-Si heterojunction has a rectifier feature with the rectification ratio over 70 at the bias of ±5 V. Also, there appears a photoelectric conversion phenomenon on this heterojunction with a short circuit current (Isc) of 0.16 μA and an open circuit voltage (Voc) of about 10 mV The high frequency C-V characteristic of the Ag/CH3NH3PbI3/p-Si heterojunction turns out to be similar to that of the metal-insulator-semiconductor (MIS) structure, and a parallel translation of the C-V curve along the forward voltage axis is found. This parallel translation means the existence of defects at the CH3NH3PbI3/p-Si interface and positive fixed charges in the CH3NH3PbI3 layer. The defects at the interface of the CH3NH3PbI3/p-Si heterojunction result in the dramatic decline of the Voc. Besides, the C-V test of CH3NH3PbI3 film shows a non-linear dielectric property and the dielectric value is about 4.64 as calculated. Project supported by the Hebei Province Natural Science Foundation of China (No. F2014202184) and the Tianjin Natural Science Foundation of China (No. 15JCZDJC37800).

Porous poly(benzimidazole) membrane for all vanadium redox flow battery

NASA Astrophysics Data System (ADS)

Luo, Tao; David, Oana; Gendel, Youri; Wessling, Matthias

2016-04-01

Porous poly(benzimidazole) (PBI) membranes of low vanadium ions permeability are described for an all vanadium redox flow battery (VRFB). The PBI membrane was prepared by a water vapour induced phase inversion process of a PBI polymer solution. The membrane has a symmetrical cross-sectional morphology. A low water permeability of 16.5 L (m2 h bar)-1 indicates the high hydraulic resistance stemming from a closed cell morphology with nanoporous characteristics. The PBI membrane doped with 2.5 M H2SO4 shows a proton conductivity of 16.6 mS cm-1 and VO2+ permeability as low as 4.5 × 10-8 cm2 min-1. The stability test of dense PBI membrane in VO2+ solution indicates good chemical stability. An all vanadium redox flow battery (VRFB) operated with the porous PBI membrane shows 98% coulombic efficiency and more than 10% higher energy efficiency compared to VRFB operated with Nafion 112 at applied current densities of 20-40 mA cm-2. High in situ stability of the porous PBI membrane was confirmed by about 50 cycles of continuous charge and discharge operation of the battery.

Bonding and expressed emotion: two interlinked concepts?

PubMed

Duclos, Jeanne; Maria, Anne-Solène; Dorard, Géraldine; Curt, Florence; Apfel, Alexandre; Vibert, Sarah; Rein, Zoé; Perdereau, Fabienne; Godart, Nathalie

2013-01-01

Bonding and expressed emotion (EE) are two concepts modeling family relationships. Two studies, with contradictory results, have explored whether these concepts and their corresponding instruments [the Parental Bonding Instrument (PBI) and the Camberwell Family Interview] do indeed measure the same aspects of family relationships. Our first objective was to compare the adolescents' perceptions of family relationships using the PBI, and the parental viewpoint using the Five-Minute Speech Sample (FMSS-EE). Secondly, we compared the PBI scores and EE levels of the parents. Sixty adolescent girls with anorexia nervosa completed the PBI. The FMSS and a modified version of the PBI were administered to parents separately. No significant link was identified between adolescent PBI scores and parental EE levels. However, a link between maternal 'modified' PBI scores and maternal EE was observed: when mothers registered a high Final EE, they were more likely to deny their daughter's psychological autonomy compared to mothers with lower EE. Our empirical results do not support the hypothesis of an overlap between the two concepts. Indeed bonding and EE measure the same object, i.e. the quality of family relationships, but time scales differ and so do the perspectives (patient vs. parental viewpoint). Copyright © 2012 S. Karger AG, Basel.

Hygrothermal behavior of polybenzimidazole

DOE PAGES

Liu, Peng; Mullins, Michael; Bremner, Tim; ...

2016-04-11

Poly[2,2’-(m-phenylene)-5,5’-bibenzimidazole] (PBI) is used in extremely high temperature harsh environment applications. It is a unique engineering material that is formed into parts by powder-sintering at temperatures as high as 500 °C. Recently, ever increasing demands for high temperature polymers have led to significant interest in PBI such that engineering guidelines could be established for its application in high temperature and highly humid environments. The goal of this work was to understand the material science of PBI in hot-wet environments at temperatures up to 288 °C. Thermal gravimetric analysis and mass spectrometry were employed to identify the degraded volatile products. Themore » molecular scale damping behavior of PBI was probed using dynamic mechanical analysis. The changes in tensile properties and fracture toughness due to environmental exposure were also characterized. Upon heating above 250 °C, moisture-containing PBI exhibits obvious molecular structure change. Evidence of crosslinking and degradation is observed. With 288 °C hot water treatment severe degradation of PBI is observed. As a result, fundamental structure-property relationships of PBI affected by these higher temperature, high moisture content environments are discussed.« less

Plasmid-mediated resistance to protein biosynthesis inhibitors in staphylococci.

PubMed

Schwarz, Stefan; Fessler, Andrea T; Hauschild, Tomasz; Kehrenberg, Corinna; Kadlec, Kristina

2011-12-01

Protein biosynthesis inhibitors (PBIs) represent powerful antimicrobial agents for the control of bacterial infections. In staphylococci, numerous resistance genes are known to be involved in resistance to PBIs, most of which mediate resistance to a specific class/subclass of PBIs, though a few genes do confer a multidrug resistance phenotype-up to five classes/subclasses of PBIs. Plasmids play a key role in the dissemination of PBI resistance among staphylococci, as they primarily carry plasmid-borne PBI resistance genes; however, plasmids also can be vectors for transposon-borne PBI resistance genes. Small plasmids that carry single PBI resistance genes are widespread among staphylococci of human and animal origin. Various mechanisms exist by which they can recombine, form cointegrates, or integrate into chromosomal DNA or larger plasmids. We provide an overview of the current knowledge of plasmid-mediated PBI resistance in staphylococci, with particular reference to the currently known PBI resistance genes, their association with mobile genetic elements, and the recombination/integration processes that control their mobility. © 2011 New York Academy of Sciences.

Copolymerization modification of poly (butylene itaconate)

NASA Astrophysics Data System (ADS)

Gao, Chuanhui; Wang, Jing; Han, Shijian; Hu, Zunfu; Liu, Yuetao

2017-08-01

A series of copolyesters-poly (butylene itaconate) (PBI) was synthesized by melt polycondensation from itaconic acid (IA) and 1,4-butanediol (BDO). On this basis, dimethyl terephthalate (DMT), adipic acid (AP) and sebacic acid (SA), respectively, was selected as the third comonomer component to modify PBI to poly (butylene itaconate-co-butylene terephthalate) (PBIT), poly (butylene itaconate-co-butylene adipate) (PBIA) and (butylene itaconate-co-butylene sebacate) (PBIS), of which structure and physical properties were characterized by FT-IR, 1H-NMR, GPC, DSC and TG. The results showed that PBI was amorphous material, and the molecular weight and the initial thermal decomposition temperature of PBI were 1108, 244°C, respectively. Compared to PBI, the molecular weight and the thermal stability of copolyesters (PBIA, PBIT and PBIS) could be increased by this treatment. Particularly, the molecular weight of PBIS was increased to 12,321, 12 times more than PBI, the initial thermal decomposition temperature was improved to 336°C, and PBIS had good crystallization performance.

Hexamethylenetetramine-mediated growth of grain-boundary-passivation CH3NH3PbI3 for highly reproducible and stable perovskite solar cells

NASA Astrophysics Data System (ADS)

Zheng, Yan-Zhen; Li, Xi-Tao; Zhao, Er-Fei; Lv, Xin-Ding; Meng, Fan-Li; Peng, Chao; Lai, Xue-Sen; Huang, Meilan; Cao, Guozhong; Tao, Xia; Chen, Jian-Feng

2018-02-01

Simultaneously achieving the long-term device stability and reproducibility has proven challenging in perovskite solar cells because solution-processing produced perovskite film with grain boundary is sensitive to moisture. Herein, we develop a hexamethylenetetramine (HMTA)-mediated one-step solution-processing deposition strategy that leads to the formation of high-purity and grain-boundary-passivation CH3NH3PbI3 film and thereby advances cell optoelectronic performance. Through morphological and structural characterizations and theoretical calculations, we demonstrate that HMTA fully occupies the moisture-exposed surface to build a bridge across grain boundary and coordinates with Pb ions to inhibit the formation of detrimental PbI2. Such HMTA-mediated grown CH3NH3PbI3 films achieves a decent augmentation of power conversion efficiency (PCE) from 12.70% to 17.87%. A full coverage of PbI2-free CH3NH3PbI3 surface on ZnO also boosts the device's stability and reproducibility.

Synergic solventing-out crystallization with subsequent time-delay thermal annealing of PbI2 precursor in mesostructured perovskite solar cells

NASA Astrophysics Data System (ADS)

Jia, Fujin; Guo, Yanqun; Che, Lijia; Liu, Zhiyong; Zeng, Zhigang; Cai, Chuanbing

2018-06-01

Although the two-step sequential deposition method provides an efficient route to fabricate high performance perovskite solar cells (PSSCs) with increasing reproducibility, the inefficient and incomplete conversion of PbI2 to perovskite is still quite a challenge. Following pioneering works, we found that the conversion process from PbI2 to perovskite mainly involves diffusion, infiltration, contact and reaction. In order to facilitate the conversion from PbI2 to perovskite, we demonstrate an effective method to regulate supersaturation level (the driving force to crystallization) of PbI2 by solventing-out crystallization combining with subsequent time-delay thermal annealing of PbI2 wet film. Enough voids and spaces in resulting porous PbI2 layer will be in favor of efficient diffusion, infiltration of CH3NH3I solution, and further enhance the contact and reaction between PbI2 and CH3NH3I in the whole film, leading to rapid, efficient and complete perovskite conversion with a conversion level of about 99.9%. Enhancement of light harvesting ranging from visible to near-IR region was achieved for the resultant high-quality perovskite. Upon this combined method, the fabricated mesostructured solar cells show tremendous power conversion efficiency (PCE) improvement from 3.2% to about 12.3% with less hysteresis owing to the simultaneous enhancement of short-circuit photocurrent density (J sc), open-circuit voltage (V oc) and fill factor (FF).

Validation of the Malay Version of the Parental Bonding Instrument among Malaysian Youths Using Exploratory Factor Analysis

PubMed Central

MUHAMMAD, Noor Azimah; SHAMSUDDIN, Khadijah; OMAR, Khairani; SHAH, Shamsul Azhar; MOHD AMIN, Rahmah

2014-01-01

Background: Parenting behaviour is culturally sensitive. The aims of this study were (1) to translate the Parental Bonding Instrument into Malay (PBI-M) and (2) to determine its factorial structure and validity among the Malaysian population. Methods: The PBI-M was generated from a standard translation process and comprehension testing. The validation study of the PBI-M was administered to 248 college students aged 18 to 22 years. Results: Participants in the comprehension testing had difficulty understanding negative items. Five translated double negative items were replaced with five positive items with similar meanings. Exploratory factor analysis showed a three-factor model for the PBI-M with acceptable reliability. Four negative items (items 3, 4, 8, and 16) and item 19 were omitted from the final PBI-M list because of incorrect placement or low factor loading (< 0.32). Out of the final 20 items of the PBI-M, there were 10 items for the care factor, five items for the autonomy factor and five items for the overprotection factor. All the items loaded positively on their respective factors. Conclusion: The Malaysian population favoured positive items in answering questions. The PBI-M confirmed the three-factor model that consisted of care, autonomy and overprotection. The PBI-M is a valid and reliable instrument to assess the Malaysian parenting style. Confirmatory factor analysis may further support this finding. Keywords: Malaysia, parenting, questionnaire, validity PMID:25977634

A two-layer structured PbI2 thin film for efficient planar perovskite solar cells.

PubMed

Ying, Chao; Shi, Chengwu; Wu, Ni; Zhang, Jincheng; Wang, Mao

2015-07-28

In this paper, a two-layer structured PbI2 thin film was constructed by the spin-coating procedure using a 0.80 M PbI2 solution in DMF and subsequent close-spaced vacuum thermal evaporation using PbI2 powder as a source. The bottom PbI2 thin film was compact with a sheet-like appearance, parallel to the FTO substrate, and can be easily converted to a compact perovskite thin film to suppress the charge recombination of the electrons of the TiO2 conduction band and the holes of the spiro-OMeTAD valence band. The top PbI2 thin film was porous with nano-sheet arrays, perpendicular to the FTO substrate, and can be easily converted to a porous perovskite thin film to improve the hole migration from the perovskite to spiro-OMeTAD and the charge separation at the perovskite/spiro-OMeTAD interface. The planar perovskite solar cells based on the two-layer structured PbI2 thin film exhibited a photoelectric conversion efficiency of 11.64%, along with an open-circuit voltage of 0.90 V, a short-circuit photocurrent density of 19.29 mA cm(-2) and a fill factor of 0.67.

Microstructures, optical and photovoltaic properties of CH3NH3PbI3(1‑x)Cl x perovskite films with CuSCN additive

NASA Astrophysics Data System (ADS)

Shirahata, Yasuhiro; Oku, Takeo

2018-05-01

Microstructures, optical and photovoltaic properties of CH3NH3PbI3(1‑x)Cl x perovskite films with copper(I) thiocyanate (CuSCN) additive were investigated. The CuSCN-added CH3NH3PbI3(1‑x)Cl x films were prepared by a hot air blow-assisted spin-coating method. Current density–voltage characteristics of the photovoltaic device using the CuSCN-added CH3NH3PbI3(1‑x)Cl x light-absorbing layer showed increases in short-circuit current density, open-circuit voltage, which resulted in increase in the conversion efficiency. Microstructure analysis showed that the crystal structure of the CuSCN-added CH3NH3PbI3(1‑x)Cl x was a pseudocubic system. From these results, partial substitutions of Pb2+ and anions (I‑ and Cl‑) by Cu ions (Cu+ and Cu2+) and SCN‑, respectively, are considered to occur in the CuSCN-added CH3NH3PbI3(1‑x)Cl x films. Based on the obtained results, reaction mechanisms of the CH3NH3PbI3(1‑x)Cl x films with and without CuSCN additive were discussed.

A Prospective Study of the Utility of Magnetic Resonance Imaging in Determining Candidacy for Partial Breast Irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorn, Paige L.; Al-Hallaq, Hania A.; Haq, Farah

2013-03-01

Purpose: Retrospective data have demonstrated that breast magnetic resonance imaging (MRI) may change a patient's eligibility for partial breast irradiation (PBI) by identifying multicentric, multifocal, or contralateral disease. The objective of the current study was to prospectively determine the frequency with which MRI identifies occult disease and to establish clinical factors associated with a higher likelihood of MRI prompting changes in PBI eligibility. Methods and Materials: At The University of Chicago, women with breast cancer uniformly undergo MRI in addition to mammography and ultrasonography. From June 2009 through May 2011, all patients were screened prospectively in a multidisciplinary conference formore » PBI eligibility based on standard imaging, and the impact of MRI on PBI eligibility according to National Surgical Adjuvant Breast and Bowel Project protocol B-39/Radiation Therapy Oncology Group protocol 0413 entry criteria was recorded. Univariable analysis was performed using clinical characteristics in both the prospective cohort and in a separate cohort of retrospectively identified patients. Pooled analysis was used to derive a scoring index predictive of the risk that MRI would identify additional disease. Results: A total of 521 patients were screened for PBI eligibility, and 124 (23.8%) patients were deemed eligible for PBI based on standard imaging. MRI findings changed PBI eligibility in 12.9% of patients. In the pooled univariable analysis, tumor size ≥2 cm on mammography or ultrasonography (P=.02), age <50 years (P=.01), invasive lobular histology (P=.01), and HER-2/neu amplification (P=.01) were associated with a higher likelihood of MRI changing PBI eligibility. A predictive score was generated by summing the number of significant risk factors. Patients with a score of 0, 1, 2, and 3 had changes to eligibility based on MRI findings in 2.8%, 13.2%, 38.1%, and 100%, respectively (P<.0001). Conclusions: MRI identified additional disease in a significant number of patients eligible for PBI, based on standard imaging. Clinical characteristics may be useful in directing implementation of MRI in the staging of PBI candidates.« less

Novel azepino-perylenebisimides: synthesis, structure, and properties.

PubMed

Mishra, Ruchika; Panini, Piyush; Sankar, Jeyaraman

2014-08-01

The first example of an azepine ring formation by counterintuitive nucleophilic participation of DBU was observed at the sterically crowded bay area of electron-deficient perylenebisimide (PBI). This is also a rare example of the formation of a seven-membered ring via two consecutive C-N bond formations in a single step. Azepino-PBIs reveal panchromatic absorption covering the whole visible region. Further novelty of these PBIs lies within the fact that their photophysical characteristics can easily be modulated by suitable substituents.

Benchtop evaluation of pressure barrier insufflator and standard insufflator systems.

PubMed

Nepple, Kenneth G; Kallogjeri, Dorina; Bhayani, Sam B

2013-01-01

Previous experimental research has reported minimal differences in pressure maintenance between different versions of standard insufflators (SI). However, a recent report identified potential clinical benefits with a valveless pressure barrier insufflator (PBI). We sought to perform a benchtop objective evaluation of SI and PBI systems. A rigid box system with continuous pressure manometry was used to evaluate a PBI (Surgiquest Airseal) and two SIs (SI1 = Stryker PneumoSure High Flow Insufflator and SI2 = Storz SCB Thermoflator). Pressure maintenance of 15 mmHg was evaluated during experimental conditions of leakage from a 5 mm port site, leakage from a 12 mm port site, and continuous suction. With leakage from the 5 mm port site, the PBI maintained pressure of >13 mmHg whereas the pressures dropped moderately with the SI1 (7-13 mmHg) and SI2 insufflators (3-7 mmHg) and did not regain goal pressure until leakage was stopped. With leakage from 12 mm port site, the PBI pressure decreased to 9-11 mmHg, whereas the SI1 and SI2 lost insufflation pressures completely. The PBI maintained pressure of >11 mmHg during continuous suction while the SI1 and SI2 lost pressure entirely, and actually showed negative pressure from air suction into the rigid box system. When evaluated statistically with the mixed model repeated measures ANOVA, the SI1 and SI2 performed similarly while the PBI maintained increased pressure. In the experimental rigid box system, the PBI more successfully maintained pressure in response to leakage and suction than SIs.

Polybenzimidazoles Via Aromatic Nucleophilic Displacement

NASA Technical Reports Server (NTRS)

Connell, John W.; Hergenrother, Paul M.; Smith, Joseph G.

1994-01-01

Soluble polybenzimidazoles (PBI's) synthesized by nucleophilic displacement reaction of di(hydroxyphenyl)-benzimidazole monomers with activated aromatic difluoride compounds in presence of anhydrous potassium carbonate. These polymers exhibit good thermal, thermo-oxidative, and chemical stability, and high mechanical properties. Using benzimidazole monomers, more economical, and new PBI's processed more easily than commercial PBI, without loss of desirable physical properties.

75 FR 49484 - Office of Postsecondary Education; Asian American and Native American Pacific Islander-Serving...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-13

...), Hispanic Serving Institutions-STEM and Articulation (HSI-STEM), and Predominantly Black Institutions (PBI... application for eligibility for AANAPISI, NASNTI, HSI-STEM, and PBI fiscal year (FY) 2010 competitions... competitions to be announced this fall under the AANAPISI, NASNTI, HSI- STEM, and PBI programs. This limited...

A Persian version of the parental bonding instrument: factor structure and psychometric properties.

PubMed

Behzadi, Behnaz; Parker, Gordon

2015-02-28

The Parental Bonding Instrument (PBI) is a widely used self-report measure for quantifying key parenting styles as perceived by the child during its first 16 years. While its development study identified two key parental dimensions, subsequent studies have variably confirmed those two or argued for one or more additional parental constructs. We developed a Persian translation of the PBI and administered it to a sample of 340 high school students. The construct validity of the Persian PBI was examined by Exploratory Factor Analysis while Confirmatory Factor Analysis was used to identify the most adequate model. Analyses of the Persian PBI favored a four-factor model for both parental forms. The Persian PBI has a factorial structure consistent with constructs identified in western cultures, as well as high internal consistency and test-retest reliability. Multivariate analyses indicated significant differences between boys and girls across some factors. The PBI appears an acceptable and appropriate measure for quantifying parent-child bonding in Iranian samples. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Homogeneous coating of ionomer on electrocatalyst assisted by polybenzimidazole as an adhesive layer and its effect on fuel cell performance

NASA Astrophysics Data System (ADS)

Yang, Zehui; Fujigaya, Tsuyohiko; Nakashima, Naotoshi

2015-12-01

The fabrication of homogeneous ionomer distribution in fuel cell catalyst layers is necessary and important to improve the platinum utilization as well as the power density. Here, we focus on the effect of poly[2,2‧-(2,6-pyridine)-5,5‧-bibenzimidazole] (PyPBI) wrapped on multi-walled carbon nanotubes (MWNTs) for anchoring Nafion ionomer to the electrocatalyst, in which PyPBI functions as the binding sites for platinum nanoparticles (Pt-NPs) used as a catalyst. Based on the result using a control composite without having PyPBI, a strong interaction of the Nafion onto the PyPBI layer is recognized. Importantly, we find that the membrane-electrode assembly (MEA) shows a much higher maximum power density than that of the MEA without PyPBI. A homogeneous coating of Nafion on the electrocatalyst using the PyPBI forms a long-range network of the ionomer, leading to an improved Pt-NP utilization efficiency as well as an enhanced power density of the MEA.

Highly Efficient Perovskite Solar Modules by Scalable Fabrication and Interconnection Optimization

DOE PAGES

Yang, Mengjin; Kim, Dong Hoe; Klein, Talysa R.; ...

2018-01-02

To push perovskite solar cell (PSC) technology toward practical applications, large-area perovskite solar modules with multiple subcells need to be developed by fully scalable deposition approaches. Here, we demonstrate a deposition scheme for perovskite module fabrication with spray coating of a TiO2 electron transport layer (ETL) and blade coating of both a perovskite absorber layer and a spiro-OMeTAD-based hole transport layer (HTL). The TiO2 ETL remaining in the interconnection between subcells significantly affects the module performance. Reducing the TiO2 thickness changes the interconnection contact from a Schottky diode to ohmic behavior. Owing to interconnection resistance reduction, the perovskite modules withmore » a 10 nm TiO2 layer show enhanced performance mainly associated with an improved fill factor. Finally, we demonstrate a four-cell MA0.7FA0.3PbI3 perovskite module with a stabilized power conversion efficiency (PCE) of 15.6% measured from an aperture area of ~10.36 cm2, corresponding to an active-area module PCE of 17.9% with a geometric fill factor of ~87.3%.« less

Highly Efficient Perovskite Solar Modules by Scalable Fabrication and Interconnection Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Mengjin; Kim, Dong Hoe; Klein, Talysa R.

To push perovskite solar cell (PSC) technology toward practical applications, large-area perovskite solar modules with multiple subcells need to be developed by fully scalable deposition approaches. Here, we demonstrate a deposition scheme for perovskite module fabrication with spray coating of a TiO2 electron transport layer (ETL) and blade coating of both a perovskite absorber layer and a spiro-OMeTAD-based hole transport layer (HTL). The TiO2 ETL remaining in the interconnection between subcells significantly affects the module performance. Reducing the TiO2 thickness changes the interconnection contact from a Schottky diode to ohmic behavior. Owing to interconnection resistance reduction, the perovskite modules withmore » a 10 nm TiO2 layer show enhanced performance mainly associated with an improved fill factor. Finally, we demonstrate a four-cell MA0.7FA0.3PbI3 perovskite module with a stabilized power conversion efficiency (PCE) of 15.6% measured from an aperture area of ~10.36 cm2, corresponding to an active-area module PCE of 17.9% with a geometric fill factor of ~87.3%.« less

CH3NH3PbI3 based solar cell: Modified by antisolvent treatment

NASA Astrophysics Data System (ADS)

Nandi, Pronoy; Giri, Chandan; Bansode, Umesh; Topwal, D.

2017-05-01

Solar cells based on new class of organic inorganic hybrid perovskite CH3NH3PbI3 were prepared by Ethyl acetate (EA); antisolvent treatment for the first time. This treatment results in new morphology for CH3NH3PbI3 thin film. FESEM image shows microrod type structures of CH3NH3PbI3 after EA antisolvent treatment. Energy band diagram was constructed using photoluminescence and photoemission studies. A better power conversion efficiency was achieved in EA treated film compare to without EA treated film.

Mesoscopic photosystems for solar light harvesting and conversion: facile and reversible transformation of metal-halide perovskites.

PubMed

Harms, Hauke Arne; Tétreault, Nicolas; Pellet, Norman; Bensimon, Michaël; Grätzel, Michael

2014-01-01

Recently, hybrid organic-inorganic metal halide perovskites have gained prominence as potent light harvesters in thin film solid-state photovoltaics. In particular the solar-to-electric power conversion efficiency (PCE) of devices using CH(3)NH(3)PbI(3) as sensitizer has increased from 3 to 20.1% within only a few years. This key material can be prepared by solution processing from PbI(2) and CH(3)NH(3)I in one step or by sequential deposition. In the latter case an electron capturing support such as TiO(2) is first covered with PbI(2), which upon exposure to a CH(3)NH(3)I solution is converted to the perovskite. Here we apply for the first time quartz crystal microbalance (QCMD) measurements in conjunction with X-ray diffraction and scanning electron microscopy to analyse the dynamics of the conversion of PbI(2) to CH(3)NH(3)PbI(3). Employing 200 nm thick PbI(2) films as substrates we discover that the CH(3)NH(3)I insertion in the PbI(2) is reversible, with the extraction into the solvent isopropanol occurring on the same time scale of seconds as the intercalation process. This offers an explanation for the strikingly rapid and facile exchange of halide ions in CH(3)NH(3)PbX(3) by solution processing at room temperature.

Current Challenges and Prospective Research for Upscaling Hybrid Perovskite Photovoltaics

DOE PAGES

Williams, Spencer T.; Rajagopal, Adharsh; Chueh, Chu-Chen; ...

2016-02-11

Organic-inorganic hybrid perovskite photovoltaics (PSCs) are poised to push toward technology translation, but significant challenges complicating commercialization remain. Though J-V hysteresis and ecotoxicity are uniquely imposing issues at scale, CH 3NH 3PbI 3 degradation is by far the sharpest limitation to the technology’s potential market contribution. Herein, we offer a perspective on the practical market potential of PSCs, the nature of fundamental PSC challenges at scale, and an outline of prospective solutions for achieving module scale PSC production tailored to intrinsic advantages of CH 3NH 3PbI 3. Although integrating PSCs into the energy grid is complicated by CH 3NH 3PbImore » 3 degradation, the ability of PSCs to contribute to consumer electronics and other niche markets like those organic photovoltaics have sought footing in rests primarily upon the technology’s price point. Thus, slot die, roll-to-roll processing has the greatest potential to enable PSC scale-up, and herein, we present a perspective on the research necessary to realize fully printable PSCs at scale.« less

One-Year stable perovskite solar cells by 2D/3D interface engineering

NASA Astrophysics Data System (ADS)

Grancini, G.; Roldán-Carmona, C.; Zimmermann, I.; Mosconi, E.; Lee, X.; Martineau, D.; Narbey, S.; Oswald, F.; de Angelis, F.; Graetzel, M.; Nazeeruddin, Mohammad Khaja

2017-06-01

Despite the impressive photovoltaic performances with power conversion efficiency beyond 22%, perovskite solar cells are poorly stable under operation, failing by far the market requirements. Various technological approaches have been proposed to overcome the instability problem, which, while delivering appreciable incremental improvements, are still far from a market-proof solution. Here we show one-year stable perovskite devices by engineering an ultra-stable 2D/3D (HOOC(CH2)4NH3)2PbI4/CH3NH3PbI3 perovskite junction. The 2D/3D forms an exceptional gradually-organized multi-dimensional interface that yields up to 12.9% efficiency in a carbon-based architecture, and 14.6% in standard mesoporous solar cells. To demonstrate the up-scale potential of our technology, we fabricate 10 × 10 cm2 solar modules by a fully printable industrial-scale process, delivering 11.2% efficiency stable for >10,000 h with zero loss in performances measured under controlled standard conditions. This innovative stable and low-cost architecture will enable the timely commercialization of perovskite solar cells.

One-Year stable perovskite solar cells by 2D/3D interface engineering

PubMed Central

Grancini, G.; Roldán-Carmona, C.; Zimmermann, I.; Mosconi, E.; Lee, X.; Martineau, D.; Narbey, S.; Oswald, F.; De Angelis, F.; Graetzel, M.; Nazeeruddin, Mohammad Khaja

2017-01-01

Despite the impressive photovoltaic performances with power conversion efficiency beyond 22%, perovskite solar cells are poorly stable under operation, failing by far the market requirements. Various technological approaches have been proposed to overcome the instability problem, which, while delivering appreciable incremental improvements, are still far from a market-proof solution. Here we show one-year stable perovskite devices by engineering an ultra-stable 2D/3D (HOOC(CH2)4NH3)2PbI4/CH3NH3PbI3 perovskite junction. The 2D/3D forms an exceptional gradually-organized multi-dimensional interface that yields up to 12.9% efficiency in a carbon-based architecture, and 14.6% in standard mesoporous solar cells. To demonstrate the up-scale potential of our technology, we fabricate 10 × 10 cm2 solar modules by a fully printable industrial-scale process, delivering 11.2% efficiency stable for >10,000 h with zero loss in performances measured under controlled standard conditions. This innovative stable and low-cost architecture will enable the timely commercialization of perovskite solar cells. PMID:28569749

One-Year stable perovskite solar cells by 2D/3D interface engineering.

PubMed

Grancini, G; Roldán-Carmona, C; Zimmermann, I; Mosconi, E; Lee, X; Martineau, D; Narbey, S; Oswald, F; De Angelis, F; Graetzel, M; Nazeeruddin, Mohammad Khaja

2017-06-01

Despite the impressive photovoltaic performances with power conversion efficiency beyond 22%, perovskite solar cells are poorly stable under operation, failing by far the market requirements. Various technological approaches have been proposed to overcome the instability problem, which, while delivering appreciable incremental improvements, are still far from a market-proof solution. Here we show one-year stable perovskite devices by engineering an ultra-stable 2D/3D (HOOC(CH 2 ) 4 NH 3 ) 2 PbI 4 /CH 3 NH 3 PbI 3 perovskite junction. The 2D/3D forms an exceptional gradually-organized multi-dimensional interface that yields up to 12.9% efficiency in a carbon-based architecture, and 14.6% in standard mesoporous solar cells. To demonstrate the up-scale potential of our technology, we fabricate 10 × 10 cm 2 solar modules by a fully printable industrial-scale process, delivering 11.2% efficiency stable for >10,000 h with zero loss in performances measured under controlled standard conditions. This innovative stable and low-cost architecture will enable the timely commercialization of perovskite solar cells.

Excited-State Vibrational Coherence in Perylene Bisimide Probed by Femtosecond Broadband Pump-Probe Spectroscopy.

PubMed

Son, Minjung; Park, Kyu Hyung; Yoon, Min-Chul; Kim, Pyosang; Kim, Dongho

2015-06-18

Broadband laser pulses with ultrashort duration are capable of triggering impulsive excitation of the superposition of vibrational eigenstates, giving rise to quantum beating signals originating from coherent wave packet motions along the potential energy surface. In this work, coherent vibrational wave packet dynamics of an N,N'-bis(2,6-dimethylphenyl)perylene bisimide (DMP-PBI) were investigated by femtosecond broadband pump-probe spectroscopy which features fast and balanced data acquisition with a wide spectral coverage of >200 nm. Clear modulations were observed in the envelope of the stimulated emission decay profiles of DMP-PBI with the oscillation frequencies of 140 and 275 cm(-1). Fast Fourier transform analysis of each oscillatory mode revealed characteristic phase jumps near the maxima of the steady-state fluorescence, indicating that the observed vibrational coherence originates from an excited-state wave packet motion. Quantum calculations of the normal modes at the low-frequency region suggest that low-frequency C-C (C═C) stretching motions accompanied by deformation of the dimethylphenyl substituents are responsible for the manifestation of such coherent wave packet dynamics.

Visible light response, electrical transport, and amorphization in compressed organolead iodine perovskites.

PubMed

Ou, Tianji; Yan, Jiejuan; Xiao, Chuanhai; Shen, Wenshu; Liu, Cailong; Liu, Xizhe; Han, Yonghao; Ma, Yanzhang; Gao, Chunxiao

2016-06-02

Recent scientific advances on organic-inorganic hybrid perovskites are mainly focused on the improvement of power conversion efficiency. So far, how compression tunes their electronic and structural properties remains less understood. By combining in situ photocurrent, impedance spectroscopy, and X-ray diffraction (XRD) measurements, we have studied the electrical transport and structural properties of compressed CH3NH3PbI3 (MAPbI3) nanorods. The visible light response of MAPbI3 remains robust below 3 GPa while it is suppressed when it becomes amorphous. Pressure-induced electrical transport properties of MAPbI3 including resistance, relaxation frequency, and relative permittivity have been investigated under pressure up to 8.5 GPa by in situ impedance spectroscopy measurements. These results indicate that the discontinuous changes of these physical parameters occur around the structural phase transition pressure. The XRD studies of MAPbI3 under high pressure up to 20.9 GPa show that a phase transformation below 0.7 GPa, could be attributed to the tilting and distortion of PbI6 octahedra. And pressure-induced amorphization is reversible at a low density amorphous state but irreversible at a relatively higher density state. Furthermore, the MAPbI3 nanorods crush into nanopieces around 0.9 GPa which helps us to explain why the mixed phase of tetragonal and orthorhombic was observed at 0.5 GPa. The pressure modulated changes of electrical transport and visible light response properties open up a new approach for exploring CH3NH3PbI3-based photo-electronic applications.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kowalchik, Kristin V.; Vallow, Laura A., E-mail: vallow.laura@mayo.edu; McDonough, Michelle

Purpose: To study the utility of preoperative breast MRI for partial breast irradiation (PBI) patient selection, using multivariable analysis of significant risk factors to create a classification rule. Methods and Materials: Between 2002 and 2009, 712 women with newly diagnosed breast cancer underwent preoperative bilateral breast MRI at Mayo Clinic Florida. Of this cohort, 566 were retrospectively deemed eligible for PBI according to the National Surgical Adjuvant Breast and Bowel Project Protocol B-39 inclusion criteria using physical examination, mammogram, and/or ultrasound. Magnetic resonance images were then reviewed to determine their impact on patient eligibility. The patient and tumor characteristics weremore » evaluated to determine risk factors for altered PBI eligibility after MRI and to create a classification rule. Results: Of the 566 patients initially eligible for PBI, 141 (25%) were found ineligible because of pathologically proven MRI findings. Magnetic resonance imaging detected additional ipsilateral breast cancer in 118 (21%). Of these, 62 (11%) had more extensive disease than originally noted before MRI, and 64 (11%) had multicentric disease. Contralateral breast cancer was detected in 28 (5%). Four characteristics were found to be significantly associated with PBI ineligibility after MRI on multivariable analysis: premenopausal status (P=.021), detection by palpation (P<.001), first-degree relative with a history of breast cancer (P=.033), and lobular histology (P=.002). Risk factors were assigned a score of 0-2. The risk of altered PBI eligibility from MRI based on number of risk factors was 0:18%; 1:22%; 2:42%; 3:65%. Conclusions: Preoperative bilateral breast MRI altered the PBI recommendations for 25% of women. Women who may undergo PBI should be considered for breast MRI, especially those with lobular histology or with 2 or more of the following risk factors: premenopausal, detection by palpation, and first-degree relative with a history of breast cancer.« less

Quantitative Assessment of Degenerative Cartilage and Subchondral Bony Lesions in a Preserved Cadaveric Knee: Propagation-Based Phase-Contrast CT Versus Conventional MRI and CT.

PubMed

Geith, Tobias; Brun, Emmanuel; Mittone, Alberto; Gasilov, Sergei; Weber, Loriane; Adam-Neumair, Silvia; Bravin, Alberto; Reiser, Maximilian; Coan, Paola; Horng, Annie

2018-06-01

The aim of this study was to quantitatively assess hyaline cartilage and subchondral bone conditions in a fully preserved cadaveric human knee joint using high-resolution x-ray propagation-based phase-contrast imaging (PBI) CT and to compare the performance of the new technique with conventional CT and MRI. A cadaveric human knee was examined using an x-ray beam of 60 keV, a detector with a 90-mm 2 FOV, and a pixel size of 46 × 46 μm 2 . PBI CT images were reconstructed with both the filtered back projection algorithm and the equally sloped tomography method. Conventional 3-T MRI and CT were also performed. Measurements of cartilage thickness, cartilage lesions, International Cartilage Repair Society scoring, and detection of subchondral bone changes were evaluated. Visual inspection of the specimen akin to arthroscopy was conducted and served as a standard of reference for lesion detection. Loss of cartilage height was visible on PBI CT and MRI. Quantification of cartilage thickness showed a strong correlation between the two modalities. Cartilage lesions appeared darker than the adjacent cartilage on PBI CT. PBI CT showed similar agreement to MRI for depicting cartilage substance defects or lesions compared with the visual inspection. The assessment of subchondral bone cysts showed moderate to strong agreement between PBI CT and CT. In contrast to the standard clinical methods of MRI and CT, PBI CT is able to simultaneously depict cartilage and bony changes at high resolution. Though still an experimental technique, PBI CT is a promising high-resolution imaging method to evaluate comprehensive changes of osteoarthritic disease in a clinical setting.

Improvement of photovoltaic performance of the inverted planar perovskite solar cells by using CH3NH3PbI3-xBrx films with solvent annealing

NASA Astrophysics Data System (ADS)

Wang, Shan; Zhang, Weijia; Ma, Denghao; Jiang, Zhaoyi; Fan, Zhiqiang; Ma, Qiang; Xi, Yilian

2018-01-01

In this paper, the CH3NH3PbI3-xBrx films with various Br-doping contents were successfully prepared by solution processed deposition and followed by annealing process. This method simultaneously modified the morphology and composition of the CH3NH3PbI3 film. The effects of annealing treatment of CH3NH3PbI3-xBrx films under N2 and DMSO conditions on the microstructure of films and photoelectric properties of the solar cells were systematically investigated. The relationship of the component ratio of RBr/I= CH3NH3PbI3-xBrx/CH3NH3PbI3 in the resulting perovskite versus CH3NH3Br concentration also was explored. The results revealed that the CH3NH3PbI3-xBrx films annealed under DMSO exhibited increased grain sizes, enhanced crystallinity, enlarged bandgap and reduced defect density compared with that of the N2 annealing. It also was found that the RBr/I linearly increased in the resulting perovskite with the increased of CH3NH3Br concentration in the methylammonium halide mixture solutions. Furthermore, the photovoltaic performances of devices fabricated using DMSO precursor solvent were worse than that of DMF under N2 annealing atmosphere. When CH3NH3Br concentration was 7.5 mg ml-1, the planar perovskite solar cell based on CH3NH3PbI3-xBrx annealed under DMSO showed the best efficiency of 13.7%.

Isolation of the endosperm-specific LPAAT gene promoter from coconut (Cocos nucifera L.) and its functional analysis in transgenic rice plants.

PubMed

Xu, Li; Ye, Rongjian; Zheng, Yusheng; Wang, Zhekui; Zhou, Peng; Lin, Yongjun; Li, Dongdong

2010-09-01

As one of the key tropical crops, coconut (Cocos nucifera L.) is a member of the monocotyledonous family Aracaceae (Palmaceae). In this study, we amplified the upstream region of an endosperm-specific expression gene, Lysophosphatidyl acyltransferase (LPAAT), from the coconut genomic DNA by chromosome walking. In this sequence, we found several types of promoter-related elements including TATA-box, CAAT-box and Skn1-motif. In order to further examine its function, three different 5'-deletion fragments were inserted into pBI101.3, a plant expression vector harboring the LPAAT upstream sequence, leading to pBI101.3-L1, pBI101.3-L2 and pBI101.3-L3, respectively. We obtained transgenic plants of rice by Agrobacterium-mediated callus transformation and plant regeneration and detected the expression of gus gene by histochemical staining and fluorometric determination. We found that gus gene driven by the three deletion fragments was specifically expressed in the endosperm of rice seeds, but not in the empty vector of pBI101.3 and other tissues. The highest expression level of GUS was at 15 DAF in pBI101.3-L3 and pBI101.3-L2 transgenic lines, while the same level was detected at 10 DAF in pBI101.3-L1. The expression driven by the whole fragment was up to 1.76- and 2.8-fold higher than those driven by the -817 bp and -453 bp upstream fragments, and 10.7-fold higher than that driven by the vector without the promoter. Taken together, our results strongly suggest that these promoter fragments from coconut have a significant potential in genetically improving endosperm in main crops.

Nanostructured poly(benzimidazole): from mesoporous networks to nanofibers.

PubMed

Weber, Jens

2010-02-22

Poly(benzimidazole)s (PBIs) are a class of high-performance polymers which have been receiving increasing interest during the last years due to their high potential as constituents of membrane materials in proton-exchange membrane fuel cells (PEMFCs). In addition to the importance of PBI in fuel-cell technology, there are a number of other applications (e.g., catalysis) that make use of the special properties of this material. The scope of this Minireview is to first give a short overview about the use of nanostructured, mesoporous PBI as a proton conductor. Secondly, the use of spirobifluorene derivatives as new monomers, which allow the synthesis of hierarchically structured PBI, is presented. Limitations of traditional synthetic methods will be discussed, and an ionothermal scheme towards PBI will be presented as a versatile tool for the synthesis of plain and spirobifluorene-based PBIs. Finally, the use of electrospinning as a powerful processing technique for PBI will be presented briefly.

Growth of PBI 2 single crystals from stoichiometric and Pb excess melts

NASA Astrophysics Data System (ADS)

Hayashi, T.; Kinpara, M.; Wang, J. F.; Mimura, K.; Isshiki, M.

2008-01-01

We have successfully grown high-purity and -quality PbI 2 single crystals by the vertical Bridgman method. The rocking curves of four-crystal X-ray diffraction (XRD) show 120 arcsec in full-width at half-maximum (FWHM). The photoluminescence (PL) spectra at 7.8 K show the resolved intensive exciton emission line and the weak DAP emission band. The deep-level emissions are not observed. The measurement of the electrical and radiographic properties show that Leadiodide (PbI 2) single crystal has a resistivity of 5×10 10 Ω cm and imager lag is 8 s, respectively. In order to improve the controllability of crystal growth, PbI 2 single crystals were also grown from a lead (Pb) excess PbI 2 source. The experimental results show very good reproducibility. In addition, the growth models of crystal are proposed, and the growth mechanism is discussed.

Modulation of PEDOT:PSS pH for efficient inverted perovskite solar cells with reduced potential loss and enhanced stability

DOE PAGES

Wang, Qin; Chueh, Chu -Chen; Eslamian, Morteza; ...

2016-11-02

Inverted p-i-n perovskite solar cells (PVSCs) using PEDOT:PSS as the hole-transporting layer (HTL) is one of the most widely adopted device structures thus far due to its facile processability and good compatibility for high throughput manufacturing processes. However, most of the PEDOT:PSS-based CH 3NH 3PbI 3 PVSCs reported to date suffered an inferior open-circuit voltage (V OC) (0.88-0.95 V) compared to that (1.05-1.12 V) obtained for common CH 3NH 3PbI 3 PVSCs, revealing a severe potential loss issue. Herein, we describe a simple method to alleviate this problem by tuning the pH value of PEDOT:PSS with a mild base, imidazole.more » Accompanied by the pH modulation, the blended imidazole concurrently tailors the surface texture and electronic properties of PEDOT:PSS to promote the quality and crystallization of the perovskite film deposited on top of it and enable better energy-level alignment at this corresponding interface. Consequently, the PVSC using this modified PEDOT:PSS HTL yields an enhanced power conversion efficiency (PCE) of 15.7% with an enlarged V OC of 1.06 V and improved long-term stability. Lastly, these outperform the pristine device showing a PCE of 12.7% with a much smaller V OC of 0.88 V and unsatisfactory environmental stability.« less

Negative Dielectric Constant Material Based on Ion Conducting Materials

NASA Technical Reports Server (NTRS)

Gordon, Keith L. (Inventor); Kang, Jin Ho (Inventor); Park, Cheol (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

2017-01-01

Metamaterials or artificial negative index materials (NIMs) have generated great attention due to their unique and exotic electromagnetic properties. One exemplary negative dielectric constant material, which is an essential key for creating the NIMs, was developed by doping ions into a polymer, a protonated poly (benzimidazole) (PBI). The doped PBI showed a negative dielectric constant at megahertz (MHz) frequencies due to its reduced plasma frequency and an induction effect. The magnitude of the negative dielectric constant and the resonance frequency were tunable by doping concentration. The highly doped PBI showed larger absolute magnitude of negative dielectric constant at just above its resonance frequency than the less doped PBI.

Negative Dielectric Constant Material Based on Ion Conducting Materials

NASA Technical Reports Server (NTRS)

Gordon, Keith L. (Inventor); Kang, Jin Ho (Inventor); Harrison, Joycelyn S. (Inventor); Park, Cheol (Inventor); Lillehei, Peter T. (Inventor)

2014-01-01

Metamaterials or artificial negative index materials (NIMs) have generated great attention due to their unique and exotic electromagnetic properties. One exemplary negative dielectric constant material, which is an essential key for creating the NIMs, was developed by doping ions into a polymer, a protonated poly(benzimidazole) (PBI). The doped PBI showed a negative dielectric constant at megahertz (MHz) frequencies due to its reduced plasma frequency and an induction effect. The magnitude of the negative dielectric constant and the resonance frequency were tunable by doping concentration. The highly doped PBI showed larger absolute magnitude of negative dielectric constant at just above its resonance frequency than the less doped PBI.

Novel hybrid membranes based on polybenzimidazole and ETS-10 titanosilicate type material for high temperature proton exchange membrane fuel cells: A comprehensive study on dense and porous systems

NASA Astrophysics Data System (ADS)

Eguizábal, A.; Lemus, J.; Urbiztondo, M.; Garrido, O.; Soler, J.; Blazquez, J. A.; Pina, M. P.

Novel hybrid membranes based on polybenzimidazole (PBI) and ETS-10 titanosilicate type materials functionalized with sulfonic groups have been developed for high temperature PEMFC applications. In particular, 45% porous ETS-10/PBI electrolyte membranes in porosity have been reported for the first time in this work. A clear conduction outperforming is shown by porous PBI + 3 wt.% SO 3H-ETS-10 doped at 50 °C, attaining "in-plane" conductivity values up to 74 mS cm -1 at 180 °C under dry N 2 flow. The transport selectivity of the as prepared dense and porous PBI based membranes has been evaluated by comparison of "in-plane" conductivity/methanol permeability values at 50 °C, 100 °C and 150 °C. Accounting from that, dense pure PBI membranes are preferred at 50 °C (4.7 × 10 6 S·s·bar mol -1); whereas at 150 °C, dense PBI + 3% SO 3H-ETS-10 counterparts exhibit the higher conductivity/methanol permeability ratio (2.5 × 10 8 S·s·bar mol -1).

Electronic structures and chemical states of methylammonium lead triiodide thin films and the impact of annealing and moisture exposure

NASA Astrophysics Data System (ADS)

Yamanaka, Soichiro; Hayakawa, Kei; Cojocaru, Ludmila; Tsuruta, Ryohei; Sato, Tomoya; Mase, Kazuhiko; Uchida, Satoshi; Nakayama, Yasuo

2018-04-01

Methylammonium lead triiodide (CH3NH3PbI3) is the fundamental material used in perovskite solar cells, and its electronic properties have, therefore, attracted a great deal of attention as a potential key to highly efficient solar cell performance. However, the deterioration of perovskite solar cells when exposed to high temperature and humidity remains a serious obstacle to the material's use, and the clarification of the degradation mechanisms has been keenly anticipated. In this study, the valence electronic structures and depth-dependence of the chemical states of CH3NH3PbI3 thin films are investigated using ultraviolet photoelectron spectroscopy and excitation energy dependent X-ray photoelectron spectroscopy. Additionally, the effects of high temperature and a moisture rich atmosphere on the CH3NH3PbI3 thin films are examined. It is confirmed that the high temperature and moist atmosphere facilitate the oxidation of CH3NH3PbI3, whereas the Pb:I stoichiometry of the CH3NH3PbI3 thin films is found to be preserved at its original ratio (1:3) after thermal annealing and exposure to a moist atmosphere.

Fast diffusion of native defects and impurities in perovskite solar cell material CH 3NH 3PbI 3

DOE PAGES

Yang, Dongwen; Ming, Wenmei; Shi, Hongliang; ...

2016-06-01

CH 3NH 3PbI 3-based solar cells have shown remarkable progress in recent years but have also suffered from structural, electrical, and chemical instabilities related to the soft lattices and the chemistry of these halides. One of the instabilities is ion migration, which may cause current–voltage hysteresis in CH 3NH 3PbI 3 solar cells. Significant ion diffusion and ionic conductivity in CH 3NH 3PbI 3 have been reported; their nature, however, remain controversial. In the literature, the use of different experimental techniques leads to the observation of different diffusing ions (either iodine or CH 3NH 3 ion); the calculated diffusion barriersmore » for native defects scatter in a wide range; the calculated defect formation energies also differ qualitatively. These controversies hinder the understanding and the control of the ion migration in CH 3NH 3PbI 3. In this paper, we show density functional theory calculations of both the diffusion barriers and the formation energies for native defects (V I +, MA i +, V MA –, and I i –) and the Au impurity in CH 3NH 3PbI 3. V I + is found to be the dominant diffusing defect due to its low formation energy and the low diffusion barrier. I i – and MA i + also have low diffusion barriers but their formation energies are relatively high. The hopping rate of V I + is further calculated taking into account the contribution of the vibrational entropy, confirming V I + as a fast diffuser. We discuss approaches for managing defect population and migration and suggest that chemically modifying surfaces, interfaces, and grain boundaries may be effective in controlling the population of the iodine vacancy and the device polarization. We further show that the formation energy and the diffusion barrier of Au interstitial in CH 3NH 3PbI 3 are both low. As a result, it is thus possible that Au can diffuse into CH3NH3PbI3 under bias in devices (e.g., solar cell, photodetector) with Au/CH 3NH 3PbI 3 interfaces and modify the electronic properties of CH 3NH 3PbI 3.« less

Fast diffusion of native defects and impurities in perovskite solar cell material CH 3NH 3PbI 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Dongwen; Ming, Wenmei; Shi, Hongliang

CH 3NH 3PbI 3-based solar cells have shown remarkable progress in recent years but have also suffered from structural, electrical, and chemical instabilities related to the soft lattices and the chemistry of these halides. One of the instabilities is ion migration, which may cause current–voltage hysteresis in CH 3NH 3PbI 3 solar cells. Significant ion diffusion and ionic conductivity in CH 3NH 3PbI 3 have been reported; their nature, however, remain controversial. In the literature, the use of different experimental techniques leads to the observation of different diffusing ions (either iodine or CH 3NH 3 ion); the calculated diffusion barriersmore » for native defects scatter in a wide range; the calculated defect formation energies also differ qualitatively. These controversies hinder the understanding and the control of the ion migration in CH 3NH 3PbI 3. In this paper, we show density functional theory calculations of both the diffusion barriers and the formation energies for native defects (V I +, MA i +, V MA –, and I i –) and the Au impurity in CH 3NH 3PbI 3. V I + is found to be the dominant diffusing defect due to its low formation energy and the low diffusion barrier. I i – and MA i + also have low diffusion barriers but their formation energies are relatively high. The hopping rate of V I + is further calculated taking into account the contribution of the vibrational entropy, confirming V I + as a fast diffuser. We discuss approaches for managing defect population and migration and suggest that chemically modifying surfaces, interfaces, and grain boundaries may be effective in controlling the population of the iodine vacancy and the device polarization. We further show that the formation energy and the diffusion barrier of Au interstitial in CH 3NH 3PbI 3 are both low. As a result, it is thus possible that Au can diffuse into CH3NH3PbI3 under bias in devices (e.g., solar cell, photodetector) with Au/CH 3NH 3PbI 3 interfaces and modify the electronic properties of CH 3NH 3PbI 3.« less

A process evaluation of performance-based incentives for village health workers in Kisoro district, Uganda

PubMed Central

2014-01-01

Background Designing effective incentive systems for village health workers (VHWs) represents a longstanding policy issue with substantial impact on the success and sustainability of VHW programs. Using performance-based incentives (PBI) for VHWs is an approach that has been proposed and implemented in some programs, but has not received adequate review and evaluation in the peer-reviewed literature. We conducted a process evaluation examining the use of PBI for VHWs in Kisoro, Uganda. In this system, VHWs are paid based on 20 indicators, divided among routine follow-up visits, health education activities, new patient identifications, sanitation coverage, and uptake of priority health services. Methods Surveys of VHWs (n = 30) and program supervisors (n = 7) were conducted to assess acceptability and feasibility. Interviews were conducted with all 8 program supervisors and with 6 purposively selected VHWs to gain a deeper understanding of their views on the PBI system. Program budget records were used to assess the costs of the program. Detailed payment records were used to assess the fairness of the PBI system with respect to VHWs’ gender, education level, and village location. Results In surveys and interviews, supervisors expressed high satisfaction with the PBI system, though some supervisors expressed concerns about possible negative effects from the variation in payments between VHWs and the uncertainty of reward for effort. VHWs perceived the system as generally fair, and preferred it to the previous payment system, but expressed a desire to be paid more. The annual program cost was $516 per VHW, with each VHW covering an average of 115 households. VHWs covering more households tended to earn more. There was some evidence that female gender was associated with higher earnings. Education level and proximity to the district hospital did not appear to be associated with earnings under the PBI system. Conclusions In a one-year pilot of PBI within a small VHW program, both VHWs and supervisors found the PBI system acceptable and motivating. VHWs with relatively limited formal education were able to master the PBI system. Further research is needed to determine the long-term effects and scalability of PBI, as well as the effects across varied contexts. PMID:24712405

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Yushan

In this work, multiple polymer backbones were screened for oxidation resistance and multiple chemistries were explored for tethering tris(2,4,6-trimethylphenyl)phosphonium (9MeTTP +) to the selected polymer backbones. A new tethering strategy through brominated 9MeTTP+ cation was developed and used to obtain the desired 9MeTTP +-functionalized polysulfone (PSf) and hexafluoro polybenzimidazole (F 6PBI) polymer. The crosslinked 9MeTTP+-functionalized hexafluoro polybenzimidazole (9MeTTP-F 6PBI) polymer demonstrated excellent oxidation stability that met the go-no-go milestone of the first year. However, large-scale bromination inevitably involved multi-bromination products, which led to polymer crosslinking in the next tethering. A new synthesis strategy with diiodobutane as linker was developed tomore » overcome the crosslinking problem. The prepared 9MeTTP +-F 6PBI membrane without crosslinking showed only 3.58% water uptake and less than 1 mS/cm OH - conductivity in water at 20°C, possibly due to the hydrophobic 9MeTTP + cation. In order to improve the conductivity, hydrophilic tris(2,4,6-trimethoxylphenyl)phosphonium (9MeOTTP+) cation was tethered to an F 6PBI backbone, and a 9MeOTTP +-F 6PBI PTFE reinforced membrane was prepared with 17.4% water uptake to increase the mechanical strength and durability in cerium (IV) solution. A 9MeOTTP+-F 6PBI PTFE reinforced membrane had less than 20% conductivity loss during an accelerated stability test in 0.5 M cerium (IV) and 1.3 M HClO 4 at 55°C for 100 hours. Moreover, a 9MeOTTP +-F 6PBI PTFE reinforced membrane had more than double the lifetime of commercial FAS-30 and FAB-PK-130 AEMs during an accelerated stability test in 0.5 M cerium (IV) and 1.3 M HClO 4 at 55°C. Low area specific resistance (ASR) of a 9MeOTTP +-F 6PBI PTFE reinforced membrane in the sulfuric acid system was also achieved due to the high acid doping ability of the polymer structure. The cationic 9MeOTTP +-F 6PBI PTFE reinforced membrane shows a cerium (IV) permeability that is 27-fold lower than that of Nafion 212. Excellent voltage and energy efficiencies with a 9MeOTTP +-F 6PBI PTFE reinforced membrane were demonstrated in an all-vanadium redox flow battery (VRFB).« less

Enhancing the Durability and Carrier Selectivity of Perovskite Solar Cells Using a Blend Interlayer.

PubMed

Sin, Dong Hun; Jo, Sae Byeok; Lee, Seung Goo; Ko, Hyomin; Kim, Min; Lee, Hansol; Cho, Kilwon

2017-05-31

A mechanically and thermally stable and electron-selective ZnO/CH 3 NH 3 PbI 3 interface is created via hybridization of a polar insulating polymer, poly(ethylene glycol) (PEG), into ZnO nanoparticles (NPs). PEG successfully passivates the oxygen defects on ZnO and prevents direct contact between CH 3 NH 3 PbI 3 and defects on ZnO. A uniform CH 3 NH 3 PbI 3 film is formed on a soft ZnO:PEG layer after dispersion of the residual stress from the volume expansion during CH 3 NH 3 PbI 3 conversion. PEG also increases the work of adhesion of the CH 3 NH 3 PbI 3 film on the ZnO:PEG layer and holds the CH 3 NH 3 PbI 3 film with hydrogen bonding. Furthermore, PEG tailors the interfacial electronic structure of ZnO, reducing the electron affinity of ZnO. As a result, a selective electron-collection cathode is formed with a reduced electron affinity and a deep-lying valence band of ZnO, which significantly enhances the carrier lifetime (473 μs) and photovoltaic performance (15.5%). The mechanically and electrically durable ZnO:PEG/CH 3 NH 3 PbI 3 interface maintains the sustainable performance of the solar cells over 1 year. A soft and durable cathodic interface via PEG hybridization in a ZnO layer is an effective strategy toward flexible electronics and commercialization of the perovskite solar cells.

Can Parental Bonding Be Assessed in Children? Factor Structure and Factorial Invariance of the Parental Bonding Instrument (PBI) between Adults and Children

ERIC Educational Resources Information Center

Tsaousis, Ioannis; Mascha, Katerina; Giovazolias, Theodoros

2012-01-01

This study examined the factorial structure of the Parental Bonding Instrument (PBI) in the Greek population. Using confirmatory factor analysis different proposed models of the basic dimensions of PBI were evaluated. The results indicated that Kendler's three-factor (i.e. care, protectiveness and authoritarianism) solution was found to be more…

Mid-infrared emission and Judd-Ofelt analysis of Dy3+-doped infrared Ga-Sb-S and Ga-Sb-S-PbI2 chalcohalide glasses

NASA Astrophysics Data System (ADS)

Guo, Jixiao; Jiao, Qing; He, Xiaolong; Guo, Hansong; Tong, Jianghao; Zhang, Zhihang; Jiang, Fuchao; Wang, Guoxiang

2018-03-01

Dy3+-doped Ga-Sb-S and Ga-Sb-S-PbI2 chalcohalide glasses were prepared by traditional melt quenching method. The effect of halide PbI2 on the physical and optical properties of Dy3+ ions was investigated. The density and ionic concentration of the host sample increased with the introduction of PbI2 halides, whereas the refractive index at 1.55 μm decreased. The Judd-Ofelt parameters showed that Ω2 increased in PbI2-modified glass, whereas the Ω6 value showed the opposite tendency. Infrared emission spectrum also showed that the intensity increased with PbI2 addition, and considerable enhancement at 2.8 μm was observed in the mid-infrared region. The halide PbI2 promoted the reduction of phonon energy of the host and the improvement of the laser pump efficiency, which led to the construction of optimized infrared glass materials for optical applications.

Thermodynamic origin of instability in hybrid halide perovskites

PubMed Central

Tenuta, E.; Zheng, C.; Rubel, O.

2016-01-01

Degradation of hybrid halide perovskites under the influence of environmental factors impairs future prospects of using these materials as absorbers in solar cells. First principle calculations can be used as a guideline in search of new materials, provided we can rely on their predictive capabilities. We show that the instability of perovskites can be captured using ab initio total energy calculations for reactants and products augmented with additional thermodynamic data to account for finite temperature effects. Calculations suggest that the instability of CH3NH3PbI3 in moist environment is linked to the aqueous solubility of the CH3NH3I salt, thus making other perovskite materials with soluble decomposition products prone to degradation. Properties of NH3OHPbI3, NH3NH2PbI3, PH4PbI3, SbH4PbI3, CsPbBr3, and a new hypothetical SF3PbI3 perovskite are studied in the search for alternative solar cell absorber materials with enhanced chemical stability. PMID:27883032

Parental bonding and vulnerability to adolescent suicide.

PubMed

Martin, G; Waite, S

1994-04-01

Part of a series of studies into early detection in adolescent suicide, this study investigated relationships between parenting style and suicidal thoughts, acts and depression. Students (mean age 15 years) from 4 randomly chosen high schools completed self-report questionnaires containing the Parental Bonding Instrument (PBI) and the Youth Self Report, which provided information about suicide ideation, deliberate self-harm and depression. Significant differences for mean scores on the PBI subscales were noted between cases and noncases of depression, suicidal thoughts and deliberate self-harm. Assignment by adolescents of their parents to the "affectionless control" quadrant of the PBI doubles the relative risk for suicidal thoughts, increases the relative risk for deliberate self-harm 3-fold and increases the relative risk for depression 5-fold. It seems that the PBI may play a role in identification of vulnerable adolescents; further, it both elucidates aspects of adolescent-parent interaction and points toward areas for intervention with at-risk adolescents. We recommend the use of the PBI in early detection studies of adolescent suicide.

High Temperature Polybenzimidazole Hollow Fiber Membranes for Hydrogen Separation and Carbon Dioxide Capture from Synthesis Gas

DOE PAGES

Singh, Rajinder P.; Dahe, Ganpat J.; Dudeck, Kevin W.; ...

2014-12-31

Sustainable reliance on hydrocarbon feedstocks for energy generation requires CO₂ separation technology development for energy efficient carbon capture from industrial mixed gas streams. High temperature H₂ selective glassy polymer membranes are an attractive option for energy efficient H₂/CO₂ separations in advanced power production schemes with integrated carbon capture. They enable high overall process efficiencies by providing energy efficient CO₂ separations at process relevant operating conditions and correspondingly, minimized parasitic energy losses. Polybenzimidazole (PBI)-based materials have demonstrated commercially attractive H₂/CO₂ separation characteristics and exceptional tolerance to hydrocarbon fuel derived synthesis (syngas) gas operating conditions and chemical environments. To realize a commerciallymore » attractive carbon capture technology based on these PBI materials, development of high performance, robust PBI hollow fiber membranes (HFMs) is required. In this work, we discuss outcomes of our recent efforts to demonstrate and optimize the fabrication and performance of PBI HFMs for use in pre-combustion carbon capture schemes. These efforts have resulted in PBI HFMs with commercially attractive fabrication protocols, defect minimized structures, and commercially attractive permselectivity characteristics at IGCC syngas process relevant conditions. The H₂/CO₂ separation performance of these PBI HFMs presented in this document regarding realistic process conditions is greater than that of any other polymeric system reported to-date.« less

Nanostructured polyurethane perylene bisimide ester assemblies with tuneable morphology and enhanced stability

NASA Astrophysics Data System (ADS)

Zhang, Xiaoxiao; Gong, Tingyuan; Chi, Hong; Li, Tianduo

2018-03-01

Size control has been successfully achieved in inorganic materials, but it remains a challenge in polymer nanomaterials due to their polydispersity. Here, we report a facile approach to tailor the diameters of polyurethane (PU) nanoparticles (490 nm, 820 nm and 2.1 µm) via perylene bisimide (PBI) assisted self-assembly. The formed morphologies such as spindle, spherical and core-shell structures depend on the ratio of PBI and polymer concentrations. It is shown that the formation of PU nanoparticles is directed by π-π stacking of PBI and the morphology transition is not only affected by the amount of PBI incorporated, but also influenced by solvent, which controls the initial evaporation balance. Furthermore, the prepared PUs exhibit retained optical stability and enhanced thermal stability. The PUs, designed to have conjugated PBI segments in backbones, were synthesized via ring-opening and condensation reactions. Compared with the neat PU, gel permeation chromatography shows narrower molecular weight distribution. Fluorescence spectra and ultraviolet-visible spectra indicate retained maximum emission wavelength of PBI at 574 nm and 5.2% quantum yields. Thermo-gravimetric analysis and differential scanning calorimetry reveal 79°C higher decomposition temperature and 22°C higher glass transition temperature. This study provides a new way to fabricate well-defined nanostructures of functionalized PUs.

MOVPE growth of Ga(PBi) on GaP and GaP on Si with Bi fractions up to 8%

NASA Astrophysics Data System (ADS)

Nattermann, L.; Beyer, A.; Ludewig, P.; Hepp, T.; Sterzer, E.; Volz, K.

2017-04-01

Dilute bismide containing materials can play an important role in addressing the issue of finding new highly efficient lasers for telecommunications as well as sensing applications. In the last several years a growing body of literature has emerged, particularly on the growth of Ga(AsBi). However, the metal organic vapor phase epitaxy growth of Ga(AsBi) with high amounts of Bi, which are necessary to overcome Auger recombination and reach telecommunications wavelengths, still remains a challenge. Ga(PBi) could be a promising alternative, but has not been deposited with significant amounts of Bi so far. A second argument for Ga(PBi) is that it could be grown on GaP, which was already deposited on Si. A number of researchers have reported theoretical calculations on the band structure of Ga(PBi), but experimental results are still lacking. In this work we present the first Ga(PBi) structures, grown by metal organic vapor phase epitaxy on GaP and on GaP on Si. By careful characterization with high resolution X-ray diffraction, atomic force microscopy, secondary ion mass spectrometry and scanning transmission electron microscopy, we will show that we have realized high quality Ga(PBi) with Bi fractions over 8%.

Band Tailing and Deep Defect States in CH 3NH 3Pb(I 1–xBr x) 3 Perovskites As Revealed by Sub-Bandgap Photocurrent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sutter-Fella, Carolin M.; Miller, D. Westley; Ngo, Quynh P.

Organometal halide perovskite semiconductors have emerged as promising candidates for optoelectronic applications because of the outstanding charge carrier transport properties, achieved with low-temperature synthesis. In this paper, we present highly sensitive sub-bandgap external quantum efficiency (EQE) measurements of Au/spiro-OMeTAD/CH 3NH 3Pb(I 1–xBr x) 3/TiO 2/FTO/glass photovoltaic devices. The room-temperature spectra show exponential band tails with a sharp onset characterized by low Urbach energies (E u) over the full halide composition space. The Urbach energies are 15–23 meV, lower than those for most semiconductors with similar bandgaps (especially with E g > 1.9 eV). Intentional aging of CH 3NH 3Pb(I 1–xBrmore » x) 3 for up to 2300 h, reveals no change in E u, despite the appearance of the PbI 2 phase due to decomposition, and confirms a high degree of crystal ordering. Moreover, sub-bandgap EQE measurements reveal an extended band of sub-bandgap electronic states that can be fit with one or two point defects for pure CH 3NH 3PbI 3 or mixed CH 3NH 3Pb(I 1–xBr x) 3 compositions, respectively. Finally, the study provides experimental evidence of defect states close to the midgap that could impact photocarrier recombination and energy conversion efficiency in higher bandgap CH 3NH 3Pb(I 1–xBr x) 3 alloys.« less

Band Tailing and Deep Defect States in CH 3NH 3Pb(I 1–xBr x) 3 Perovskites As Revealed by Sub-Bandgap Photocurrent

DOE PAGES

Sutter-Fella, Carolin M.; Miller, D. Westley; Ngo, Quynh P.; ...

2017-02-15

Organometal halide perovskite semiconductors have emerged as promising candidates for optoelectronic applications because of the outstanding charge carrier transport properties, achieved with low-temperature synthesis. In this paper, we present highly sensitive sub-bandgap external quantum efficiency (EQE) measurements of Au/spiro-OMeTAD/CH 3NH 3Pb(I 1–xBr x) 3/TiO 2/FTO/glass photovoltaic devices. The room-temperature spectra show exponential band tails with a sharp onset characterized by low Urbach energies (E u) over the full halide composition space. The Urbach energies are 15–23 meV, lower than those for most semiconductors with similar bandgaps (especially with E g > 1.9 eV). Intentional aging of CH 3NH 3Pb(I 1–xBrmore » x) 3 for up to 2300 h, reveals no change in E u, despite the appearance of the PbI 2 phase due to decomposition, and confirms a high degree of crystal ordering. Moreover, sub-bandgap EQE measurements reveal an extended band of sub-bandgap electronic states that can be fit with one or two point defects for pure CH 3NH 3PbI 3 or mixed CH 3NH 3Pb(I 1–xBr x) 3 compositions, respectively. Finally, the study provides experimental evidence of defect states close to the midgap that could impact photocarrier recombination and energy conversion efficiency in higher bandgap CH 3NH 3Pb(I 1–xBr x) 3 alloys.« less

The Role of Connectivity on Electronic Properties of Lead Iodide Perovskite-Derived Compounds

PubMed Central

2017-01-01

We use a layered solution crystal growth method to synthesize high-quality single crystals of two different benzylammonium lead iodide perovskite-like organic/inorganic hybrids. The well-known (C6H5CH2NH3)2PbI4 phase is obtained in the form of bright orange platelets, with a structure comprised of single ⟨100⟩-terminated sheets of corner-sharing PbI6 octahedra separated by bilayers of the organic cations. The presence of water during synthesis leads to formation of a novel minority phase that crystallizes in the form of nearly transparent, light yellow bar-shaped crystals. This phase adopts the monoclinic space group P21/n and incorporates water molecules, with structural formula (C6H5CH2NH3)4Pb5I14·2H2O. The crystal structure consists of ribbons of edge-sharing PbI6 octahedra separated by the organic cations. Density functional theory calculations including spin–orbit coupling show that these edge-sharing PbI6 octahedra cause the band gap to increase with respect to corner-sharing PbI6 octahedra in (C6H5CH2NH3)2PbI4. To gain systematic insight, we model the effect of the connectivity of PbI6 octahedra on the band gap in idealized lead iodide perovskite-derived compounds. We find that increasing the connectivity from corner-, via edge-, to face-sharing causes a significant increase in the band gap. This provides a new mechanism to tailor the optical properties in organic/inorganic hybrid compounds. PMID:28677956

Growing large columnar grains of CH3NH3PbI3 using the solid-state reaction method enhanced by less-crystallized nanoporous PbI2 films

NASA Astrophysics Data System (ADS)

Zheng, Huifeng; Wang, Weiqi; Liu, Yangqiao; Sun, Jing

2017-03-01

Compact, pinhole-free and PbI2-free perovskite films, are desirable for high-performance perovskite solar cells (PSCs), especially if large columnar grains are obtained in which the adverse effects of grain boundaries will be minimized. However, the conventional solid-state reaction methods, originated from the two-step method, failed to grow columnar grains of CH3NH3PbI3 in a facile way. Here, we demonstrate a strategy for growing large columnar grains of CH3NH3PbI3, by less-crystallized nanoporous PbI2 (ln-PbI2) film enhanced solid-state reaction method. We demonstrated columnar grains were obtainable only when ln-PbI2 films were applied. Therefore, the replacement of compact PbI2 by ln-PbI2 in the solid-sate reaction, leads to higher power conversion efficiency, better reproducibility, better stability and less hysteresis. Furthermore, by systematically investigating the effects of annealing temperature and duration, we found that an annealing temperature ≥120 °C was also critical for growing columnar grains. With the optimal process, a champion efficiency of 16.4% was obtained and the average efficiency reached 14.2%. Finally, the mechanism of growing columnar grains was investigated, in which a VPb″ -assisted hooping model was proposed. This work reveals the origins of grain growth in the solid-state reaction method, which will contribute to preparing high quality perovskite films with much larger columnar grains.

A Randomized Trial of a Parent-Based Intervention on Drinking Behavior Among Incoming College Freshmen*

PubMed Central

Ichiyama, Michael A.; Fairlie, Anne M.; Wood, Mark D.; Turrisi, Rob; Francis, Diane P.; Ray, Anne E.; Stanger, Louise A.

2009-01-01

Objective: Despite research suggesting that parental involvement can affect alcohol involvement among adolescents, few studies have focused on parent-based alcohol prevention strategies among college undergraduates. We report the results of a randomized trial of a parent-based intervention (PBI) in a sample of college freshmen. Method: Across two cohorts, 724 incoming freshman—parent dyads completed baseline assessments and were randomly assigned to PBI or intervention as usual (an alcohol fact sheet for parents). Student follow-up assessments were completed at 4 and 8 months. Results: Two-part latent growth curve modeling was used to test hypothesized intervention effects. Outcome variables were drinks per week (past month), heavy episodic drinking (past 2 weeks), and alcohol-related problems (past 3 months). Over the 8-month follow-up period, PBI had a significant effect on drinks per week but not heavy episodic drinking or alcohol-related problems. Specifically, compared with students in the intervention-as-usual condition, students receiving the PBI were significantly less likely to transition from nondrinker to drinker status and showed less growth in drinking over the freshman year. However, the direct PBI effect on growth was qualified by a PBI × Gender interaction, with probes indicating that the effect applied to women but not men in the PBI condition. Conclusions: This study extends previous research by demonstrating the potential utility for PBIs to decrease the likelihood of transitioning into drinker status and, at least for women, for slowing growth in drinking over the freshman year. PMID:19538914

Mixed-Organic-Cation (FA)x(MA)1-xPbI3 Planar Perovskite Solar Cells with 16.48% Efficiency via a Low-Pressure Vapor-Assisted Solution Process.

PubMed

Chen, Jing; Xu, Jia; Xiao, Li; Zhang, Bing; Dai, Songyuan; Yao, Jianxi

2017-01-25

Compared to that of methylammonium lead iodide perovskite (MAPbI 3 ), formamidinium lead iodide perovskite (FAPbI 3 ) has a smaller energy band gap and greater potential efficiency. To prevent the transformation of α-FAPbI 3 to δ-FAPbI 3 , preparation of (FA) x (MA) 1-x PbI 3 was regarded as an effective route. Usually, the planar (FA) x (MA) 1-x PbI 3 perovskite solar cells are fabricated by a solution process. Herein, we report a low-pressure vapor-assisted solution process (LP-VASP) for the growth of (FA) x (MA) 1-x PbI 3 perovskite solar cells that features improved electron transportation, uniform morphology, high power conversion efficiency (PCE), and better crystal stability. In LP-VASP, the (FA) x (MA) 1-x PbI 3 films were formed by the reaction between the PbI 2 film with FAI and MAI vapor in a very simple vacuum oven. LP-VASP is an inexpensive way to batch-process solar cells, avoiding the repeated deposition solution process for PbI 2 films, and the device had a low cost. We demonstrate that, with an increase in the MAI content, the (101) peak position of FAPbI 3 shifts toward the (110) peak position of MAPbI 3 , the (FA) x (MA) 1-x PbI 3 perovskites are stable, and no decomposition or phase transition is observed after 14 days. The photovoltaic performance was effectively improved by the introduction of MA + with the highest efficiency being 16.48% under conditions of 40 wt % MAI. The carrier lifetime of (FA) x (MA) 1-x PbI 3 perovskite films is approximately three times longer than that of pure FAPbI 3 . Using this process, solar cells with a large area of 1.00 cm 2 were fabricated with the PCE of 8.0%.

Perceived parenting behavior in the childhood of cocaine users: relationship with genotype and personality traits.

PubMed

Gerra, G; Zaimovic, A; Garofano, L; Ciusa, F; Moi, G; Avanzini, P; Talarico, E; Gardini, F; Brambilla, F; Manfredini, M; Donnini, C

2007-01-05

Low parental care during childhood, a pattern characteristic of an "affectionless control" rearing style was frequently reported in the history of addicted individuals. Parents' childrearing regimes and children's genetic predispositions, with their own behavioral characteristics, have been seen to be closely interwoven, probably affecting children's development and addictive behavior susceptibility. In the present study, parents care perception, aggressive personality traits, and genotype (serotonin transporter promoter gene--5-HTTLPR) have been investigated in cocaine users and healthy control subjects. PBI scores (maternal and paternal care) were lower and BDHI scores (aggressiveness) higher in cocaine users in comparison with controls and significant differences in the perception of either paternal or maternal care were observed between cocaine users and non-users. The short-short (SS) genotype frequency was significantly higher among cocaine users compared with control subjects (P = 0.04). Logistic regression proves that persons bearing the SS genotype have a risk of becoming cocaine user almost three times higher than those having the LL genotype. Estimations of the effects of other factors potentially affecting the risk of being cocaine addicted clearly prove the significant impact of aggressiveness: the highest the score, the highest the risk of becoming cocaine user. Moreover, paternal and maternal care perception significantly improve the fit of the model (the log likelihood decreases passing from -105.9 to -89.8, LR test = 32.17, P-value = 0.0000). Each unit increase in the PBI score yields a significant 12% and 10% decrease of the risk of becoming cocaine user, respectively for paternal and maternal care. Interestingly, once controlled for the PBI score, the relative risk associated to the SS genotype drops strikingly and becomes no longer statistically significant. On the whole, our preliminary data suggest that the association between 5-HT transporter polymorphism and psycho-stimulant use may be mediated by mother-child relationship and parental attachment perception, both being environmental and genetic factors involved in the proneness to substance use disorders, particularly in aggressive-antisocial individuals.

CH3 NH3 PbI3 and HC(NH2 )2 PbI3 Powders Synthesized from Low-Grade PbI2 : Single Precursor for High-Efficiency Perovskite Solar Cells.

PubMed

Zhang, Yong; Kim, Seul-Gi; Lee, Do-Kyoung; Park, Nam-Gyu

2018-05-09

High-efficiency perovskite solar cells are generally fabricated by using highly pure (>99.99 %) PbI 2 mixed with an organic iodide in polar aprotic solvents. However, the use of such an expensive chemical may impede progress toward large-scale industrial applications. Here, we report on the synthesis of perovskite powders by using inexpensive low-grade (99 %) PbI 2 and on the photovoltaic performance of perovskite solar cells prepared from a powder-based single precursor. Pure APbI 3 [A=methylammonium (MA) or formamidinium (FA)] perovskite powders were synthesized by treating low-grade PbI 2 with MAI or FAI in acetonitrile at ambient temperature. The structural phase purity was confirmed by X-ray diffraction. The solar cell with a MAPbI 3 film prepared from the synthesized perovskite powder demonstrated a power conversion efficiency (PCE) of 17.14 %, which is higher than the PCE of MAPbI 3 films prepared by using both MAI and PbI 2 as precursors (PCE=13.09 % for 99 % pure PbI 2 and PCE=16.39 % for 99.9985 % pure PbI 2 ). The synthesized powder showed better absorption and photoluminescence, which were responsible for the better photovoltaic performance. For the FAPbI 3 powder, a solution with a yellow non-perovskite δ-FAPbI 3 powder synthesized at room temperature was found to lead to a black perovskite film, whereas a solution with the black perovskite α-FAPbI 3 powder synthesized at 150 °C was not transformed into a black perovskite film. The α↔δ transition between the powder and film was assumed to correlate with the difference in the iodoplumbates in the powder-dissolved solution. An average PCE of 17.21 % along with a smaller hysteresis [ΔPCE=PCE reverse -PCE forward )=1.53 %] was demonstrated from the perovskite solar cell prepared by using δ-FAPbI 3 powder; this PCE is higher than the average PCE of 17.05 % with a larger hysteresis (ΔPCE=2.71 %) for a device based on a conventional precursor solution dissolving MAI with high-purity PbI 2 . The smaller hysteresis was indicative of fewer defects in the resulting FAPbI 3 film prepared by using the δ-FAPbI 3 powder. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Physical Security Against Explosive Threats: Standoff Magnetic and Electro-optical Sensing and Target Characterization

DTIC Science & Technology

2012-10-21

PBIEDS ). Coupled with recent suicide bomb events in unstable regions of Southwest Asia and Africa, long-standing Urgent Operation Need Statements for...explosives and shrapnel (metal screws, bolts, ball bearings). A PBIED detection capability is critically needed not only for operations during open...produce magnetic signals above a certain threshold. We have developed a simple and robust multi- modal sensing system to detect PBIEDs and metal

Tympanic membrane perforation after combat blast exposure in Iraq: a poor biomarker of primary blast injury.

PubMed

Harrison, Corey D; Bebarta, Vikhyat S; Grant, Gerald A

2009-07-01

The US military has reported over 10,000 improvised explosive device attacks attributing to over 400 deaths in Iraq in 2005. Otologic blast injury and tympanic membrane (TM) perforation have traditionally been used as a predictor, or biomarker, of serious or occult primary blast injury (PBI). Although combat injuries from the US-Iraq conflict have been described, the utility of TM perforation as a marker of PBI has not. The objective of this study is to determine the incidence of tympanic perforation in patients subject to blast exposures and describe its utility as a biomarker of more serious primary barotrauma, as observed at a US military hospital in Iraq. In our institutional review board-approved study, all patients during a 30-day period who arrived at a tertiary US military hospital in Iraq were evaluated. All patients with blast injures were identified on arrival to the hospital emergency department and were followed up through their hospital course and evacuation to the United States to assure they received proper otolaryngology evaluation and follow-up. Demographic data and manifestations of PBI (TM perforation, pneumothorax, pulmonary contusion, nonpenetrating facial sinus injury, and bowel perforation) and other combat injuries were recorded. The diagnostic tests and clinical examination findings used to identify these complications were also recorded. One hundred sixty-seven patients were enrolled over 30 days. All blast exposures resulted from primary or secondary explosions from munitions used in combat. This included both combatants and civilians. All patients were men. The mean patient age was 28 years (range, 12-55 years). Sixteen percent (27 of 167) of blast-exposed patients had TM perforation. Thirteen of 27 patients with perforations had bilateral perforations. Twelve of 167 patients (7%) had PBI. Six of 12 patients (50%) with PBI had TM perforation. The use of TM perforation as a biomarker for PBI resulted in a sensitivity of 50% (95% CI, 22-78%) and specificity of 87% (95% CI, 81-92%). Both TM perforation and PBI are rare with improvised explosive devices and other explosive devices in the current Iraqi-US conflict. Contrary to previous belief and management guidelines, TM perforation had low sensitivity for serious or occult PBI and was not a good biomarker. On the basis of the findings of this study, the absence of TM perforation does not appear to exclude other serious PBI.

Mobile, Multimodal, Label-Free Imaging Probe Analysis of Choroidal Oximetry and Retinal Hypoxia

DTIC Science & Technology

2017-12-01

these same eye injuries. Primary blast-induced injury (PBI), which can occur in eyes that are not punctured or ruptured by the blast, is correlated ...optimization. (1A-F) The component of our PBI- devices, output pressure detection sensor, amplifier, and input pressure panel. (1G) Correlation between...by changing the setting of blast generator. (2A-B) Correlation between output pressure and blast time duration. (2C) After PBI- treatment, the eyes of

Minorities and Women in Naval Aviation Training: A Look Back at a 1997 Study

DTIC Science & Technology

2011-02-28

Flight Aptitude Rating (FOFAR), the Pilot Biographical Inventory ( PBI ), the NFO Biographical Inventory (FOBI), and the Officer Aptitude Rating (OAR...Hiatt, et al., 1997). The AQR measures math and verbal skills, the FAR and PFAR assess mechanical and visual spatial abilities, and the PBI and FOBI...three composites: the AQR, the PFAR, and PBI for pilots; and a parallel composite for NFOs. Selection to the aviation program was made based on

Impact of Alkyl Spacer Length on Aggregation Pathways in Kinetically Controlled Supramolecular Polymerization.

PubMed

Ogi, Soichiro; Stepanenko, Vladimir; Thein, Johannes; Würthner, Frank

2016-01-20

We have investigated the kinetic and thermodynamic supramolecular polymerizations of a series of amide-functionalized perylene bisimide (PBI) organogelator molecules bearing alkyl spacers of varied lengths (ethylene to pentylene chains, PBI-1-C2 to PBI-1-C5) between the amide and PBI imide groups. These amide-functionalized PBIs form one-dimensional fibrous nanostructures as the thermodynamically favored states in solvents of low polarity. Our in-depth studies revealed, however, that the kinetic behavior of their supramolecular polymerization is dependent on the spacer length. Propylene- and pentylene-tethered PBIs follow a similar polymerization process as previously observed for the ethylene-tethered PBI. Thus, the monomers of these PBIs are kinetically trapped in conformationally restricted states through intramolecular hydrogen bonding between the amide and imide groups. In contrast, the intramolecularly hydrogen-bonded monomers of butylene-tethered PBI spontaneously self-assemble into nanoparticles, which constitute an off-pathway aggregate state with regard to the thermodynamically stable fibrous supramolecular polymers obtained. Thus, for this class of π-conjugated system, an unprecedented off-pathway aggregate with high kinetic stability could be realized for the first time by introducing an alkyl linker of optimum length (C4 chain) between the amide and imide groups. Our current system with an energy landscape of two competing nucleated aggregation pathways is applicable to the kinetic control over the supramolecular polymerization by the seeding approach.

Polybenzimidazole (PBI) functionalized nanographene as highly stable catalyst support for polymer Electrolyte membrane fuel cells (PEMFCs)

DOE PAGES

Xin, Le; Yang, Fan; Qiu, Yang; ...

2016-08-25

Nanoscale graphenes were used as cathode catalyst supports in proton exchange membrane fuel cells (PEMFCs). Surface-initiated polymerization that covalently bonds polybenzimidazole (PBI) polymer on the surface of graphene supports enables the uniform distribution of the Pt nanoparticles, as well as allows the sealing of the unterminated carbon bonds usually present on the edge of graphene from the chemical reduction of graphene oxide. The nanographene effectively shortens the length of channels and pores for O 2 diffusion/water dissipation and significantly increases the primary pore volume. Further addition of p-phenyl sulfonic functional graphitic carbon particles as spacers, increases the specific volume ofmore » the secondary pores and greatly improves O 2 mass transport within the catalyst layers. The developed composite cathode catalyst of Pt/PBI-nanographene (50 wt%) + SO 3H-graphitic carbon black demonstrates a higher beginning of life (BOL) PEMFC performance as compared to both Pt/PBI-nanographene (50 wt%) and Pt/PBI-graphene (50 wt%) + SO 3H-graphitic carbon black (GCB). Accelerated stress tests show excellent support durability compared to that of traditional Pt/Vulcan XC72 catalysts, when subjected to 10,000 cycles from 1.0 V to 1.5 V. As a result, this study suggests the promise of using PBI-nanographene + SO 3H-GCB hybrid supports in fuel cells to achieve the 2020 DOE targets for transportation applications.« less

[A Case of Transorbital Penetrating Brain Injury Caused by a Steel Wire Entirely Embedded in the Brain Parenchyma].

PubMed

Kin, Kyohei; Ono, Yasuhiro; Fujimori, Takeshi; Kuramoto, Satoshi; Katsumata, Atsushi; Goda, Yuji; Kawauchi, Masamitsu

2015-10-01

Penetrating brain injury(PBI)is very rare in Japan. Because there is a very wide variety of pathological condition of PBI, the guideline for the treatment of PBI has not been established yet. We report the unique case of PBI caused by a steel wire piece completely embedded in the brain parenchyma. A 75-year-old man was brought to the emergency department due to ocular injury caused by a steel wire piece. Neurological examination revealed only left visual disturbance. CT scan revealed a steel wire piece located intraparenchymally between the left frontal lobe and the ventricles, but digital subtraction angiography showed no significant vascular injury in the surrounding structures. We performed an open surgery and removed the steel wire piece. Because the steel wire piece was completely embedded in the brain, we used intraoperative X-ray fluoroscopy to choose a less invasive approach for the brain. The patient suffered no additional neurological deficit and no sign of cerebral infection or seizure after surgery. He was discharged after a 4-week administration of antibiotics. In most cases of PBI caused by low velocity injury, foreign bodies are not completely embedded in the brain except for remnants after surgical removal. This is the first report of low velocity PBI caused by a foreign body completely embedded in the brain.

High-performance perovskite CH3NH3PbI3 thin films for solar cells prepared by single-source physical vapour deposition

PubMed Central

Fan, Ping; Gu, Di; Liang, Guang-Xing; Luo, Jing-Ting; Chen, Ju-Long; Zheng, Zhuang-Hao; Zhang, Dong-Ping

2016-01-01

In this work, an alternative route to fabricating high-quality CH3NH3PbI3 thin films is proposed. Single-source physical vapour deposition (SSPVD) without a post-heat-treating process was used to prepare CH3NH3PbI3 thin films at room temperature. This new process enabled complete surface coverage and moisture stability in a non-vacuum solution. Moreover, the challenges of simultaneously controlling evaporation processes of the organic and inorganic sources via dual-source vapour evaporation and the heating process required to obtain high crystallization were avoided. Excellent composition with stoichiometry transferred from the powder material, a high level of tetragonal phase-purity, full surface coverage, well-defined grain structure, high crystallization and reproducibility were obtained. A PCE of approximately 10.90% was obtained with a device based on SSPVD CH3NH3PbI3. These initial results suggest that SSPVD is a promising method to significantly optimize perovskite CH3NH3PbI3 solar cell efficiency. PMID:27426686

Thermal stability and molecular ordering of organic semiconductor monolayers: effect of an anchor group.

PubMed

Jones, Andrew O F; Knauer, Philipp; Resel, Roland; Ringk, Andreas; Strohriegl, Peter; Werzer, Oliver; Sferrazza, Michele

2015-06-08

The thermal stability and molecular order in monolayers of two organic semiconductors, PBI-PA and PBI-alkyl, based on perylene derivatives with an identical molecular structure except for an anchor group for attachment to the substrate in PBI-PA, are reported. In situ X-ray reflectivity measurements are used to follow the stability of these monolayers in terms of order and thickness as temperature is increased. Films have thicknesses corresponding approximately to the length of one molecule; molecules stand upright on the substrate with a defined structure. PBI-PA monolayers have a high degree of order at room temperature and a stable film exists up to 250 °C, but decomposes rapidly above 300 °C. In contrast, stable physisorbed PBI-alkyl monolayers only exist up to 100 °C. Above the bulk melting point at 200 °C no more order exists. The results encourage using anchor groups in monolayers for various applications as it allows enhanced stability at the interface with the substrate. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhanced performance in perovskite solar cells via bromide ion substitution and ethanol treatment

NASA Astrophysics Data System (ADS)

Feng, Bingjie; Duan, Jinxia; Tao, Li; Zhang, Jun; Wang, Hao

2018-02-01

Mixed lead halide (Pb(I1-xBrx)2) as the seed layer was employed to prepare mixed lead-halide perovskite (MAPbI3-2xBr2x, MA = CH3NH3) films through two-step sequential deposition method. Ethanol treatment process was also introduced for the control of morphology and microstructure of Pb(I1-xBrx)2 films. The ethanol treatment accelerates the crystallization of Pb(I1-xBrx)2 and the resulted Pb(I1-xBrx)2 films exhibit a porous structure which facilitates more complete conversion of PbI2 at the same time. As a result, high purity and highly crystallized MAPbI3-2xBr2x films are obtained. The photovoltaic performance of assembled perovskite solar cells based on MAPbI3-2xBr2x films are improved upon ethanol treatment and a champion power conversion efficiency (PCE) of 15.53% is obtained with x = 0.2. After exposed in air condition for 14 days, a 86% of initial PCE remains in the champion device.

Interfacial Charge-Carrier Trapping in CH3NH3PbI3-Based Heterolayered Structures Revealed by Time-Resolved Photoluminescence Spectroscopy.

PubMed

Yamada, Yasuhiro; Yamada, Takumi; Shimazaki, Ai; Wakamiya, Atsushi; Kanemitsu, Yoshihiko

2016-06-02

The fast-decaying component of photoluminescence (PL) under very weak pulse photoexcitation is dominated by the rapid relaxation of the photoexcited carriers into a small number of carrier-trapping defect states. Here, we report the subnanosecond decay of the PL under excitation weaker than 1 nJ/cm(2) both in CH3NH3PbI3-based heterostructures and bare thin films. The trap-site density at the interface was evaluated on the basis of the fluence-dependent PL decay profiles. It was found that high-density defects determining the PL decay dynamics are formed near the interface between CH3NH3PbI3 and the hole-transporting Spiro-OMeTAD but not at the CH3NH3PbI3/TiO2 interface and the interior regions of CH3NH3PbI3 films. This finding can aid the fabrication of high-quality heterointerfaces, which are required improving the photoconversion efficiency of perovskite-based solar cells.

Psychometric Validation of the Parental Bonding Instrument in a U.K. Population-Based Sample: Role of Gender and Association With Mental Health in Mid-Late Life.

PubMed

Xu, Man K; Morin, Alexandre J S; Marsh, Herbert W; Richards, Marcus; Jones, Peter B

2016-08-01

The factorial structure of the Parental Bonding Instrument (PBI) has been frequently studied in diverse samples but no study has examined its psychometric properties from large, population-based samples. In particular, important questions have not been addressed such as the measurement invariance properties across parental and offspring gender. We evaluated the PBI based on responses from a large, representative population-based sample, using an exploratory structural equation modeling method appropriate for categorical data. Analysis revealed a three-factor structure representing "care," "overprotection," and "autonomy" parenting styles. In terms of psychometric measurement validity, our results supported the complete invariance of the PBI ratings across sons and daughters for their mothers and fathers. The PBI ratings were also robust in relation to personality and mental health status. In terms of predictive value, paternal care showed a protective effect on mental health at age 43 in sons. The PBI is a sound instrument for capturing perceived parenting styles, and is predictive of mental health in middle adulthood. © The Author(s) 2016.

Neuroimaging in adult penetrating brain injury: a guide for radiographers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Temple, Nikki; Donald, Cortny; Skora, Amanda

Penetrating brain injuries (PBI) are a medical emergency, often resulting in complex damage and high mortality rates. Neuroimaging is essential to evaluate the location and extent of injuries, and to manage them accordingly. Currently, a myriad of imaging modalities are included in the diagnostic workup for adult PBI, including skull radiography, computed tomography (CT), magnetic resonance imaging (MRI) and angiography, with each modality providing their own particular benefits. This literature review explores the current modalities available for investigating PBI and aims to assist in decision making for the appropriate use of diagnostic imaging when presented with an adult PBI. Basedmore » on the current literature, the authors have developed an imaging pathway for adult penetrating brain injury that functions as both a learning tool and reference guide for radiographers and other health professionals. Currently, CT is recommended as the imaging modality of choice for the initial assessment of PBI patients, while MRI is important in the sub-acute setting where it aids prognosis prediction and rehabilitation planning, Additional follow-up imaging, such as angiography, should be dependent upon clinical findings.« less

Exploring the Photovoltaic Performance of All-Inorganic Ag2PbI4/PbI2 Blends.

PubMed

Frolova, Lyubov A; Anokhin, Denis V; Piryazev, Alexey A; Luchkin, Sergey Yu; Dremova, Nadezhda N; Troshin, Pavel A

2017-04-06

We present an all-inorganic photoactive material composed of Ag 2 PbI 4 and PbI 2 , which shows unexpectedly good photovoltaic performance in planar junction solar cells delivering external quantum efficiencies of ∼60% and light power conversion efficiencies of ∼3.9%. The revealed characteristics are among the best reported to date for metal halides with nonperovskite crystal structure. Most importantly, the obtained results suggest a possibility of reaching high photovoltaic efficiencies for binary and, probably, also ternary blends of different inorganic semiconductor materials. This approach, resembling the bulk heterojunction concept guiding the development of organic photovoltaics for two decades, opens wide opportunities for rational design of novel inorganic and hybrid materials for efficient and sustainable photovoltaic technologies.

Interface architecture between TiO2/perovskite, perovskite/hole transport layer, and perovskite grain boundary(Conference Presentation)

NASA Astrophysics Data System (ADS)

Hayase, Shuzi; Hirotani, Daisuke; Moriya, Masahiro; Ogomi, Yuhei; Shen, Qing; Yoshino, Kenji; Toyoda, Taro

2016-09-01

In order to examine the interface structure of TiO2/perovskite layer, quartz crystal microbalance sensor (QCM) was used. On the QCM sensor, TiO2 layer was fabricated and the PbI2 solution in Dimethylformamide (DMF) was passed on the QCM sensor to estimate the adsorption density of the PbI2 on the titania2. The amount of PbI2 adsorption on TiO2 surface increased as the adsorption time and leveled off at a certain time. PbI2 still remained even after the solvent only (DMF) was passed on the TiO2 layer on QCM (namely rinsing with DMF), suggesting that the PbI2 was tightly bonded on the TiO2 surface. The bonding structure was found to be Ti-O-Pb linkage by XPS analysis. We concluded that the Ti-OH on the surface of TiO2 reacts with I-Pb-I to form Ti-O-Pb-I and HI (Fig.1 B). The surface trap density was measured by thermally stimulated current (TSC) method. Before the PbI2 passivation, the trap density of TiO2 was 1019 cm3. The trap density decreased to 1016/cm3 after the PbI2 passivation, suggesting that the TiO2 surface trap was passivated with I-Pb-I. The passivation density was tuned by the concentration of PbI2 in DMF, by which TiO2 layer was passivated. Perovskite solar cells were fabricated on the passivated TiO2 layer with various PbI2 passivation densities by one step process (mixture of PbI2 + MAI in DMF). It was found that Jsc increased with an increase in the Ti-O-Pb density. We concluded that the interface between TiO2 and perovskite layer has passivation structure consisting of Ti-O-Pb-I which decreases the trap density of the interfaces and supresses charge recombination. The effect of Cl anion on high efficiency is still controversial when perovskite layer is prepared by one step method from the mixture of MAI and PbCl2. It was found that adsorption density of PbCl2 on TiO2 surface was much higher than that of PbI2 from the experiment using QCM sensor. After the surface was washed with DMF, Cl and Pb were detected. These results suggest that the TiO2 surface was much more passivated by PbCl2 than by PbI2. This may explain partially the high efficiency when the perovskite layer was fabricated by one step process consisting of MAI and PbCl2 solution. We also observed that the crystal size increased with an increase in the amount of Cl anion which of course one of the explanation of the high efficiency. The interface of hole transport layer/perovskite layer, and between perovskite layer /perovskite layer (grain boundary) was passivated with organic amines. The passivation was also effective for increasing Voc and Jsc. This was explained by the results of transient absorption spectroscopy that the charge recombination time between hole transport payer/perovskite layer increased from 0.3 μsec to 60 μsec.

Crew/cargo and logistics module definition

NASA Technical Reports Server (NTRS)

1971-01-01

The logistics requirements for the space station cargo, the initial buildup, and the 90 day resupply are presented, along with the conceptual selection for the orbiter crew accommodations and the GSS logistics system. Various module configurations are outlined; structural/mechanical, environmental, temperature, voice communication, and data bus subsystems are also reviewed. Ground operations and module prelaunch and launch operations are discussed, as well as logistics system interfaces for space shuttles and stations.

Military Uniforms: Issues Related to the Supply of Flame Resistant Fibers for the Production of Military Uniforms

DTIC Science & Technology

2011-06-30

fibers. A variety of fibers may be used to create a fabric blend, including FR rayon, Nomex®, Twaron®, Kevlar®, FR cotton, polybenzimidazole ( PBI ...as meta-aramids (e.g., Nomex®), modacrylic, PBI , and FR-treated cotton. o For example, the Army is currently testing fabrics in an attempt to...considering fabric blends containing FR-treated cotton as a potential alternative. o The Marine Corps uses PBI fibers in its balaclava (a protective

Effect of Human and Sheep Lung Orientation on Primary Blast Injury Induced by Single Blast

DTIC Science & Technology

2010-09-01

may be injured by m ore than one of these mechanisms in any given event. Primary blast in juries ( PBI ) are exclusively caused by the blast...overpressure. A PBI usually affects air-containing organs such as t he lung, ears and gastrointestinal tract. Secon dary blast injuries are caused by...orientation on blast injuries predicted in human and sheep models. From th is study, it is predicted that the greatest reduction in lung PBI may be

Photodissociation of PbI2 in the ultraviolet: analysis of the A rightarrow X band of PbI

NASA Astrophysics Data System (ADS)

Rodriguez, G.; Herring, C. M.; Fraser, R. D.; Eden, J. G.

1996-07-01

Emission and absorption studies of lead moniodide (PbI) have been carried out by photodissociation of PbI2 vapor at one of several wavelengths (193, 248, 266, 308, and 351 nm) in the ultraviolet. Strong emission on the A \\rightarrow X2 Pi 1/2 band (14400-22800 cm -1 ; 440 \\similar-or-less lambda \\similar-or-less 695 nm) occurs when PbI2 is photodissociated at 248 or 266 nm. Also, absorption bands attributed to the B \\leftarrow X2 Pi 1/2,3/2 , D \\leftarrow X2 Pi 1/2,3/2 , and E \\leftarrow X2 Pi 1/2,3/2 transitions of the diatomic molecule have been observed at 290 and 380, 225 and 265, and 203 and 240 nm, respectively, as have emission bands peaking at 397.6, 531.6, 582.0, 595.1, 639.7, 685.9, and 707.9 nm that appear to arise from PbI2 itself. Analysis and computer simulations of the A \\rightarrow X2 Pi 1/2 emission spectra have resulted in identifications for virtually all (>120) of the observed vibrational bandheads. Several spectroscopic constants for the A and the X2 Pi 1/2 states of PbI have been determined to be Te(A)=20659+/-130 cm-1 , omega e\\prime =132.2+/-1.0cm -1 , omega e\\prime xe\\prime =1.91+/-0.06cm -1 , omega e\\prime \\prime=160.3+/-0.6cm-1 , and omega e\\prime \\primexe \\prime\\prime=0.24+/-0.03cm -1 . Also, the difference between the equilibrium internuclear separations for the X2 Pi 1/2 and the A states has been determined to be Delta Re=0.45+/-0.05 . The spontaneous-emission lifetime for the PbI(A) state and the rate constant for quenching of this state by PbI2 (in two-body collisions) have been measured to be (94.3+/-8.8) ns and (4.3+/-0.4) \\times 10-10 cm3s -1 , respectively.

Synthesis, purification and bulk crystal growth of radiation detector materials using melt growth technique

NASA Astrophysics Data System (ADS)

Surabhi, Raja Rahul Reddy

In the past decade, there has been new and increased usage of radiation-detection technologies for applications in homeland security, non-proliferation, and national defense. Most of these applications require a portable device with high gamma-ray energy resolution and detection efficiency, compact size, room-temperature operation, and low cost. Consequently, there is a renewed understanding of the material limitations for these technologies and a great demand to develop next-generation radiation-detection materials that can operate at room temperature. Mercuric iodide (HgI2), Lead iodide (PbI2), and CdZnTe (CZT) are the current leading candidates for radiation detector applications. This is because of their high atomic number and large band gap that makes them particularly well suited for fabrication of high resolution and high efficiency compact devices. PbI2 is a promising material for room temperature nuclear radiation detectors, characterized by its wide band gap (EG=2.32eV) and high-density (rho=6.2g/cm3). It has been reported that PbI2 crystal detectors are able to detect gamma-ray in the range of 1KeV-1MeV, with good energy resolution. However, PbI 2 detectors have not been studied in detail because of non-availability of high quality single crystals. This study presents the synthesis, purification, growth and characterization of PbI2 single crystals grown. In this research, solid-state synthesis technique has been utilized for obtaining PbI2 as a starting material. For the first time, a unique low-temperature purification technique has been developed to obtain high-purity starting material. The crystals were grown using 2-zone Bridgman-Stockbarger (B.S) technique wherein growth rate and temperature gradient at the solid-liquid interface were optimized. Single crystals of PbI2 were successfully grown in quartz glass ampoule under different growth conditions. Material purity was determined by measuring the elemental concentration using the Inductively coupled plasma-optical emission spectroscopy (ICP-OES). ICP-OES is utilized for estimating impurities present in the low-temperature purified material, zone refined material and melt grown PbI2 crystals. The zone-refined material contains no traceable amounts of impurities, whereas the low-temperature purified material and melt grown PbI2 crystals show very low concentration of K (potassium) and Na (sodium) impurities. Crystal characterization has been performed for determining optical properties by UV-VIS spectroscopy. The energy band gap (EG) is an important parameter for materials used for room temperature gamma-ray detector applications. The absorption peak at 530nm is a characteristic of PbI2 and corresponds to the onset of the transitions from the valence band to the exciton level. From this absorption spectrum the calculated indirect band gap of PbI 2 was 2.33+/-0.025 eV at room temperature. For measuring the electrical properties (Dielectric and I-V characteristics) of the crystal, Ag (silver) contacts are applied to both sides of the sample. Dielectric analysis on melt grown PbI2 showed that space charge polarization was dominant at lower frequencies but stabilizes at higher frequencies over different operating temperatures. On the other hand, dielectric analysis for zone-refined material space charge polarization was constant over the operating range resulting in fewer lattice defects. Therefore the low temperature purified material followed by zone-refined purification provides detector grade material with fewer lattice defects. The measured electrical resistivity for melt grown PbI2 and zone-refined material are 3.185 x 10 10 O-cm and 0.754 x 109 O-cm at room temperature along (001) plane respectively.

JEM Experiment Logistics Module Pressurized Section

NASA Image and Video Library

2007-04-02

In the Space Station Processing Facility, the JEM Experiment Logistics Module Pressurized Section is lowered onto a scale for weight and center-of-gravity measurements. The module will then be moved to a work stand. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

Perylene bisimide hydrogels and lyotropic liquid crystals with temperature-responsive color change.

PubMed

Görl, Daniel; Soberats, Bartolome; Herbst, Stefanie; Stepanenko, Vladimir; Würthner, Frank

2016-11-01

The self-assembly of perylene bisimide (PBI) dyes bearing oligo ethylene glycol (OEG) units in water affords responsive functional nanostructures characterized by their lower critical solution temperature (LCST). Tuning of the LCST is realized by a supramolecular approach that relies on two structurally closely related PBI-OEG molecules. The two PBIs socially co-assemble in water and the resulting nanostructures exhibit a single LCST in between the transition temperatures of the aggregates formed by single components. This permits to precisely tune the transition from a hydrogel to a lyotropic liquid crystal state at temperatures between 26 and 51 °C by adjusting the molar fraction of the two PBIs. Owing to concomitant changes in PBI-PBI interactions this phase transition affords a pronounced color change with "fluorescence-on" response that can be utilized as a smart temperature sensory system.

Shape-Evolution Control of hybrid perovskite CH3NH3PbI3 crystals via solvothermal synthesis

NASA Astrophysics Data System (ADS)

Zhang, Baohua; Guo, Fuqiang; Yang, Lianhong; Jia, Xiuling; Liu, Bin; Xie, Zili; Chen, Dunjun; Lu, Hai; Zhang, Rong; Zheng, Youdou

2017-02-01

We systematically synthesized CH3NH3PbI3 crystals using solvothermal process, and the reaction conditions such as concentration of the precursor, temperature, time, and lead source have been comprehensively investigated to obtain shape-controlled CH3NH3PbI3 crystals. The results showed that the CH3NH3PbI3 crystals exhibit tetragonal phase and the crystals change from nanoparticles to hopper-faced cuboids. Photoluminescence spectra of the crystals obtained with different lead sources show a blue shift due to the presence of defects in the crystals, and the peak intensity is very sensitive to the lead sources. Moreover, impurities (undesirable byproducts and excess components like HI or CH3NH2) presented during crystal growth can result in hopper growth.

Crystallization Dynamics of Organolead Halide Perovskite by Real-Time X-ray Diffraction.

PubMed

Miyadera, Tetsuhiko; Shibata, Yosei; Koganezawa, Tomoyuki; Murakami, Takurou N; Sugita, Takeshi; Tanigaki, Nobutaka; Chikamatsu, Masayuki

2015-08-12

We analyzed the crystallization process of the CH3NH3PbI3 perovskite by observing real-time X-ray diffraction immediately after combining a PbI2 thin film with a CH3NH3I solution. A detailed analysis of the transformation kinetics demonstrated the fractal diffusion of the CH3NH3I solution into the PbI2 film. Moreover, the perovskite crystal was found to be initially oriented based on the PbI2 crystal orientation but to gradually transition to a random orientation. The fluctuating characteristics of the crystallization process of perovskites, such as fractal penetration and orientational transformation, should be controlled to allow the fabrication of high-quality perovskite crystals. The characteristic reaction dynamics observed in this study should assist in establishing reproducible fabrication processes for perovskite solar cells.

Columnar Self-Assembly of Electron-Deficient Dendronized Bay-Annulated Perylene Bisimides.

PubMed

Gupta, Ravindra Kumar; Shankar Rao, Doddamane S; Prasad, S Krishna; Achalkumar, Ammathnadu S

2018-03-07

Three new heteroatom bay-annulated perylene bisimides (PBIs) have been synthesized by microwave-assisted synthesis in excellent yield. N-annulated and S-annulated perylene bisimides exhibited columnar hexagonal phase, whereas Se-annulated perylene bisimide exhibited low temperature columnar oblique phase in addition to the high temperature columnar hexagonal phase. The cup shaped bay-annulated PBIs pack into columns with enhanced intermolecular interactions. In comparison to PBI, these molecules exhibited lower melting and clearing temperature, with good solubility. A small red shift in the absorption was seen in the case of N-annulated PBI, whereas S- and Se-annulated PBIs exhibited blue-shifted absorption spectra. Bay-annulation increased the HOMO and LUMO levels of the N-annulated perylene bisimide, whereas a slight increase in the LUMO level and a decrease in the HOMO levels were observed in the case of S- and Se-annulated perylene bisimides, in comparison to the simple perylene bisimide. The band gaps of PBI and PBI-N were almost same, whereas an increase in the band gaps were observed in the case of S- and Se-annulated PBIs. The tendency to freeze in the ordered glassy columnar phase for PBI-N and PBI-S will help to overcome the charge traps due to crystallization, which are detrimental to one-dimensional charge carrier mobility. These solution processable electron deficient columnar semiconductors possessing good thermal stability may form an easily accessible promising class of n-type materials. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Gypsum (CaSO4·2H2O) Scaling on Polybenzimidazole and Cellulose Acetate Hollow Fiber Membranes under Forward Osmosis

PubMed Central

Chen, Si Cong; Su, Jincai; Fu, Feng-Jiang; Mi, Baoxia; Chung, Tai-Shung

2013-01-01

We have examined the gypsum (CaSO4·2H2O) scaling phenomena on membranes with different physicochemical properties in forward osmosis (FO) processes. Three hollow fiber membranes made of (1) cellulose acetate (CA), (2) polybenzimidazole (PBI)/polyethersulfone (PES) and (3) PBI-polyhedral oligomeric silsesquioxane (POSS)/polyacrylonitrile (PAN) were studied. For the first time in FO processes, we have found that surface ionic interactions dominate gypsum scaling on the membrane surface. A 70% flux reduction was observed on negatively charged CA and PBI membrane surfaces, due to strong attractive forces. The PBI membrane surface also showed a slightly positive charge at a low pH value of 3 and exhibited a 30% flux reduction. The atomic force microscopy (AFM) force measurements confirmed a strong repulsive force between gypsum and PBI at a pH value of 3. The newly developed PBI-POSS/PAN membrane had ridge morphology and a contact angle of 51.42° ± 14.85° after the addition of hydrophilic POSS nanoparticles and 3 min thermal treatment at 95 °C. Minimal scaling and an only 1.3% flux reduction were observed at a pH value of 3. Such a ridge structure may reduce scaling by not providing a locally flat surface to the crystallite at a pH value of 3; thus, gypsum would be easily washed away from the surface. PMID:24957062

Validity of the Parental Burnout Inventory Among Dutch Employees.

PubMed

Van Bakel, Hedwig J A; Van Engen, Marloes L; Peters, Pascale

2018-01-01

The purpose of this study was to validate the Parental Burnout Inventory (PBI) in a Dutch sample of working parents. The Dutch version of the PBI and questionnaires about work were administered to 627 working parents, with at least one child living at home. We investigated whether the tri-dimensional structure of the PBI held in a sample of male and female employed parents. Furthermore, we examined the relationships between PBI and the constructs work-related burnout, depressive mood, parenting stress and work-family conflict, which we assessed with widely used and validated instruments, i.e., emotional exhaustion [a subscale of the Dutch version of Maslach's Burnout Inventory], a Dutch Parental Stress Questionnaire and Work-Family Conflict. The results support the validity of a tri-dimensional parental burnout syndrome, including exhaustion, distancing and inefficacy. Low to moderate correlations between parents' burnout symptoms and professional exhaustion, parenting stress, depressive complaints and work-family conflict experiences were found, suggesting that the concept of PBI differs significantly from the concepts of job burnout, depression and stress, respectively. The current study confirms that some parents are extremely exhausted by their parental role. However, the number of Dutch employees reporting extreme parental burnout is rather low.

Validity of the Parental Burnout Inventory Among Dutch Employees

PubMed Central

Van Bakel, Hedwig J. A.; Van Engen, Marloes L.; Peters, Pascale

2018-01-01

The purpose of this study was to validate the Parental Burnout Inventory (PBI) in a Dutch sample of working parents. The Dutch version of the PBI and questionnaires about work were administered to 627 working parents, with at least one child living at home. We investigated whether the tri-dimensional structure of the PBI held in a sample of male and female employed parents. Furthermore, we examined the relationships between PBI and the constructs work-related burnout, depressive mood, parenting stress and work-family conflict, which we assessed with widely used and validated instruments, i.e., emotional exhaustion [a subscale of the Dutch version of Maslach’s Burnout Inventory], a Dutch Parental Stress Questionnaire and Work-Family Conflict. The results support the validity of a tri-dimensional parental burnout syndrome, including exhaustion, distancing and inefficacy. Low to moderate correlations between parents’ burnout symptoms and professional exhaustion, parenting stress, depressive complaints and work-family conflict experiences were found, suggesting that the concept of PBI differs significantly from the concepts of job burnout, depression and stress, respectively. The current study confirms that some parents are extremely exhausted by their parental role. However, the number of Dutch employees reporting extreme parental burnout is rather low. PMID:29875711

Ultrafast Exciton Delocalization, Localization, and Excimer Formation Dynamics in a Highly Defined Perylene Bisimide Quadruple π-Stack.

PubMed

Kaufmann, Christina; Kim, Woojae; Nowak-Król, Agnieszka; Hong, Yongseok; Kim, Dongho; Würthner, Frank

2018-03-28

An adequately designed, bay-tethered perylene bisimide (PBI) dimer Bis-PBI was synthesized by Pd/Cu-catalyzed Glaser-type oxidative homocoupling of the respective PBI building block. This newly synthesized PBI dimer self-assembles exclusively and with high binding constants of up to 10 6 M -1 into a discrete π-stack of four chromophores. Steady-state absorption and emission spectra show the signatures of H-type excitonic coupling among the dye units. Broadband fluorescence upconversion spectroscopy (FLUPS) reveals an ultrafast dynamics in the optically excited state. An initially coherent Frenkel exciton state that is delocalized over the whole quadruple stack rapidly (τ = ∼200 fs) loses its coherence and relaxes into an excimer state. Comparison with Frenkel exciton dynamics in PBI dimeric and oligomeric H-aggregates demonstrates that in the quadruple stack coherent exciton propagation is absent due to its short length of aggregates, thereby it has only one relaxation pathway to the excimer state. Furthermore, the absence of pump-power dependence in transient absorption experiments suggests that multiexciton cannot be generated in the quadruple stack, which is in line with time-resolved fluorescence measurements.

Light-trapping in perovskite solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du, Qing Guo; Shen, Guansheng; John, Sajeev

We numerically demonstrate enhanced light harvesting efficiency in both CH 3NH 3PbI 3 and CH(NH 2) 2PbI 3-based perovskite solar cells using inverted verticalcone photonic-crystal nanostructures. For CH 3NH 3PbI 3 perovskite solar cells, the maximum achievable photocurrent density (MAPD) reaches 25.1 mA/cm 2, corresponding to 92% of the total available photocurrent in the absorption range of 300 nm to 800 nm. Our cell shows 6% absorption enhancement compared to the Lambertian limit (23.7 mA/cm 2) and has a projected power conversion efficiency of 12.9%. Excellent solar absorption is numerically demonstrated over a broad angular range from 0 to 60more » degree for both S- and P- polarizations. For the corresponding CH(NH 2) 2PbI 3 based perovskite solar cell, with absorption range of 300 nm to 850 nm, we find a MAPD of 29.1 mA/cm 2, corresponding to 95.4% of the total available photocurrent. Furthermore, the projected power conversion efficiency of the CH(NH 2) 2PbI 3 based photonic crystal solar cell is 23.4%, well above the current world record efficiency of 20.1%.« less

Cytotoxic properties of a new organometallic platinum(II) complex and its gold(I) heterobimetallic derivatives.

PubMed

Serratrice, Maria; Maiore, Laura; Zucca, Antonio; Stoccoro, Sergio; Landini, Ida; Mini, Enrico; Massai, Lara; Ferraro, Giarita; Merlino, Antonello; Messori, Luigi; Cinellu, Maria Agostina

2016-01-14

A novel platinum(ii) organometallic complex, [Pt(pbi)(Me)(DMSO)], bearing the 2-(2'-pyridyl)-benzimidazole (pbiH) ligand, was synthesized and fully characterized. Interestingly, the reaction of this organometallic platinum(ii) complex with two distinct gold(i) phosphane compounds afforded the corresponding heterobimetallic derivatives with the pbi ligand bridging the two metal centers. The antiproliferative properties in vitro of [Pt(pbi)(Me)(DMSO)] and its gold(i) derivatives as well as those of the known coordination platinum(ii) and palladium(ii) complexes with the same ligand, of the general formula [MCl2(pbiH)], were comparatively evaluated against A2780 cancer cells, either sensitive or resistant to cisplatin. A superior biological activity of the organometallic compound clearly emerged compared to the corresponding platinum(ii) complex; the antiproliferative effects are further enhanced upon attaching the gold(i) triphenylphosphine moiety to the organometallic Pt compound. Remarkably, these novel metal species are able to overcome nearly complete resistance to cisplatin. Significant mechanistic insight into the study compounds was gained after investigating their reactions with a few representative biomolecules by electrospray mass spectrometry and X-ray crystallography. The obtained results are comprehensively discussed.

Light-trapping in perovskite solar cells

DOE PAGES

Du, Qing Guo; Shen, Guansheng; John, Sajeev

2016-06-01

We numerically demonstrate enhanced light harvesting efficiency in both CH 3NH 3PbI 3 and CH(NH 2) 2PbI 3-based perovskite solar cells using inverted verticalcone photonic-crystal nanostructures. For CH 3NH 3PbI 3 perovskite solar cells, the maximum achievable photocurrent density (MAPD) reaches 25.1 mA/cm 2, corresponding to 92% of the total available photocurrent in the absorption range of 300 nm to 800 nm. Our cell shows 6% absorption enhancement compared to the Lambertian limit (23.7 mA/cm 2) and has a projected power conversion efficiency of 12.9%. Excellent solar absorption is numerically demonstrated over a broad angular range from 0 to 60more » degree for both S- and P- polarizations. For the corresponding CH(NH 2) 2PbI 3 based perovskite solar cell, with absorption range of 300 nm to 850 nm, we find a MAPD of 29.1 mA/cm 2, corresponding to 95.4% of the total available photocurrent. Furthermore, the projected power conversion efficiency of the CH(NH 2) 2PbI 3 based photonic crystal solar cell is 23.4%, well above the current world record efficiency of 20.1%.« less

Ultrathin metallized PBI paper

NASA Technical Reports Server (NTRS)

Chenevey, E. C.

1978-01-01

A study to determine the feasibility of preparing ultrathin papers with a target weight of 3.5 g/m squared from polybenzimidazole (PBI) fibrids was undertaken. Small hand sheets of target weight were fabricated. They were light brown, low density materials with sufficient strength to be readily handleable. Characterization of these sheets included strength, fold endurance, thermal gravimetric analysis in air and nitrogen and photomicrographs. Two different batches of PBI fibrids were studied and differences in fabrication performance were noted. In neither case could target weight papers be prepared using conventional paper making techniques.

KSC-07pd0636

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- A flat bed truck hauls the container with the Experiment Logistics Module Pressurized Section inside away from the Trident wharf. The logistics module is part of the Japanese Experiment Module, known as Kibo. The logistics module is being transported to the Space Station Processing Facility at NASA's Kennedy Space Center. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0635

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- A flat bed truck hauls the container with the Experiment Logistics Module Pressurized Section inside away from the Trident wharf. The logistics module is part of the Japanese Experiment Module. The logistics module is being transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0632

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- At the Trident wharf, workers help guide the container with the Experiment Logistics Module Pressurized Section inside toward the dock. The logistics module is part of the Japanese Experiment Module. The logistics module will be transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

JEM Experiment Logistics Module Pressurized Section

NASA Image and Video Library

2007-04-02

An overhead crane moves the JEM Experiment Logistics Module Pressurized Section above the floor of the Space Station Processing Facility to a scale for weight and center-of-gravity measurements. The module will then be moved to a work stand. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

JEM Experiment Logistics Module Pressurized Section

NASA Image and Video Library

2007-04-02

In the Space Station Processing Facility, an overhead crane moves the JEM Experiment Logistics Module Pressurized Section toward a scale (at left) for weight and center-of-gravity measurements. The module will then be moved to a work stand. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

JEM Experiment Logistics Module Pressurized Section

NASA Image and Video Library

2007-04-02

The JEM Experiment Logistics Module Pressurized Section is lifted from its shipping crate in the Space Station Processing Facility. The module will be moved to a scale for weight and center-of-gravity measurements and then to a work stand. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

JEM Experiment Logistics Module Pressurized Section

NASA Image and Video Library

2007-04-02

In the Space Station Processing Facility, an overhead crane lifts the JEM Experiment Logistics Module Pressurized Section from its shipping container and moves it toward a scale for weight and center-of-gravity measurements. The module will then be moved to a work stand. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

The effect of porous lead iodide precursor film on perovskite film formation and its photovoltaic property after an effective pretreatment

NASA Astrophysics Data System (ADS)

Yan, Jian-Jun; Li, Yan; Chang, Yin; Jiang, Pan; Wang, Cheng-Wei

2016-06-01

An effective solvent sealed natural drying (SND) pretreatment was introduced for forming a satisfactory crystalline porous iodide (PbI2) precursor film, which could help to generate excellent CH3NH3PbI3 perovskite films for high performance of planar heterojunction perovskite solar cells. And the influence of SND pretreated time on the device performance was investigated in detail. We found that the PbI2 precursor film after 10 min pretreatment could make the perovskite device achieve the optimal power conversion efficiency (PCE) of 8.6%, significantly increased up to 95.5% and 28.4% compared to without pretreatment or traditional treatment. The results show that the time of SND pretreatment is critical to forming large grain size and good crystallinity for PbI2 precursor film, which would markedly improve the efficiency of planar heterojunction perovskite solar cells.

An ambient stable core-substituted perylene bisimide dianion: isolation and single crystal structure analysis† †Electronic supplementary information (ESI) available: Synthesis, spectroelectrochemistry, UV-vis, electrochemistry, X-ray diffraction, NMR and mass spectra. CCDC 1032959. For ESI and crystallographic data in CIF or other electronic format see DOI: 10.1039/c4sc03671a Click here for additional data file. Click here for additional data file.

PubMed Central

Seifert, Sabine; Schmidt, David

2015-01-01

Here we report the first example of an isolable, ambient stable perylene bisimide (PBI) dianion which was synthesized by catalytic reduction of a highly electron deficient PBI derivative. The remarkable stability of this unprecedented dianion in air for months facilitated its complete characterization by different methods, including single crystal X-ray analysis. Furthermore, solvent dependent cyclic and square wave voltammetry studies revealed that the formation of PBI dianions is preferred in more polar solvents, whereas the generation of PBI radical anions should be favoured in less polar solvents. PMID:28717450

Dibenzo[a,f]perylene bisimide: effects of introducing two fused rings.

PubMed

Chaolumen; Enno, Hiroki; Murata, Michihisa; Wakamiya, Atsushi; Murata, Yasujiro

2014-11-01

Perylene bisimides (PBIs) are fascinating dyes with various potential applications. To study the effects of introducing a dibenzo-fused structure to the perylene moiety, π-extended PBI derivatives with a dibenzo-fused structure at both of the a and f bonds were synthesized. The twisted structure was characterized by X-ray crystal structure analysis. In the cyclic voltammograms, the dibenzo[a,f]-fused PBI showed a reversible oxidation wave at much less positive potential, relative to a dibenzo[a,o]-fused PBI derivative. These data indicated that two ring fusions at both sides of a naphthalene moiety, which construct a tetracene core, effectively raise the HOMO level compared to fusion of one ring at each naphthalene moiety (two anthracene cores). The dibenzo[a,f]-fused PBI derivative showed an absorption band at 735 nm with a shoulder band reaching 900 nm. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Relationship between microstructure and optical properties of a novel perovskite C12PbI4 embedded in matrix of porous alumina

NASA Astrophysics Data System (ADS)

Zaghdoudi, W.; Bardaoui, A.; Khalifa, N.; Chtourou, R.

2013-01-01

In this study, organic-inorganic hybrid perovskite multiple quantum wells (PbI QWs) embedded in porous anodic alumina (PAA) thin films on glass and aluminum substrates are investigated in detail. The pore height and diameter of the nanoscale structure of porous anodic alumina (PAA) film produced by the anodization technique are controllable. The synthesized films are characterized morphologically using the atomic force microscopy (AFM). Scanning electron microscopy (SEM) study showed granular surface. The structural and optical properties were investigated by X-ray diffraction (XRD), photoluminescence (PL) and UV-Vis-NIR spectrophotometer. The effect of the two different substrates on the impregnation of the PbI QW in the PAA is presented. Both PL and AFM studies show a better penetration of the PbI QW in the case of the Al substrate providing a wider pore diameter. Remarkable enhancement of quantum confinement is demonstrated.

Japanese Experiment Module arrival

NASA Image and Video Library

2007-03-29

Several components for delivery to the International Space Station sit in test stands inside the Space Station Processing Facility highbay. To the right, from back to front, are the Japanese Experiment Module, the Raffaello multi-purpose logistics module, and the European Space Agency's Columbus scientific research module. To the left in front is the starboard truss segment S5. Behind it is the test stand that will hold the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

Japanese Experiment Module arrival

NASA Image and Video Library

2007-03-29

The Experiment Logistics Module Pressurized Section for the Japanese Experiment Module arrives at the Space Station Processing Facility. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

Japanese Experiment Module arrival

NASA Image and Video Library

2007-03-29

The Experiment Logistics Module Pressurized Section for the Japanese Experiment Module arrives at the Space Station Processing Facility for uncrating. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

A photoelectrochemical biosensor for fibroblast-like synoviocyte cell using visible light-activated NCQDs sensitized-ZnO/CH3NH3PbI3 heterojunction.

PubMed

Pang, Xuehui; Zhang, Yong; Pan, Jihong; Zhao, Yanxia; Chen, Yao; Ren, Xiang; Ma, Hongmin; Wei, Qin; Du, Bin

2016-03-15

Based on ZnO nanorods (NRs)/CH3NH3PbI3/nitrogen-doped carbon quantum dots (NCQDs) nanocomposites, the highly sensitive detection of fibroblast-like synoviocyte (FLS) cell was realized by a photoelectrochemical (PEC) biosensor. ZnO/CH3NH3PbI3/NCQDs nanocomposites were exploited as the photo-to-electron generator to produce the signal. CH3NH3PbI3 was spin-coated on ZnO surface after ZnO NRs grew on ITO electrode then by dropping on the modified electrode, NCQDs were diffused and adhered to the surface of ZnO and CH3NH3PbI3. In the presence of EDC/NHS, the combination of CH3NH3PbI3 and NCQDs was achieved by the carboxyl groups (-COOH) and amino groups (-NH2) in the preparation process. Furthermore, the capture probe of FLS cell, CD95 antibody, can be anchored by -COOH and -NH2 groups through EDC/NHS. The specific recognition between the antibody capture probes and cell targets gained high-sensitive detection for FLS cell for the first time. The developed biosensor showed a wide linear range from 1.0 × 10(4)cell/mL to 10 cell/mL and a low detection limit of 2 cell/mL. This kind of biosensor would provide a novel detection strategy for FLS cell. Copyright © 2015 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Qin; Chueh, Chu -Chen; Eslamian, Morteza

Inverted p-i-n perovskite solar cells (PVSCs) using PEDOT:PSS as the hole-transporting layer (HTL) is one of the most widely adopted device structures thus far due to its facile processability and good compatibility for high throughput manufacturing processes. However, most of the PEDOT:PSS-based CH 3NH 3PbI 3 PVSCs reported to date suffered an inferior open-circuit voltage (V OC) (0.88-0.95 V) compared to that (1.05-1.12 V) obtained for common CH 3NH 3PbI 3 PVSCs, revealing a severe potential loss issue. Herein, we describe a simple method to alleviate this problem by tuning the pH value of PEDOT:PSS with a mild base, imidazole.more » Accompanied by the pH modulation, the blended imidazole concurrently tailors the surface texture and electronic properties of PEDOT:PSS to promote the quality and crystallization of the perovskite film deposited on top of it and enable better energy-level alignment at this corresponding interface. Consequently, the PVSC using this modified PEDOT:PSS HTL yields an enhanced power conversion efficiency (PCE) of 15.7% with an enlarged V OC of 1.06 V and improved long-term stability. Lastly, these outperform the pristine device showing a PCE of 12.7% with a much smaller V OC of 0.88 V and unsatisfactory environmental stability.« less

KSC-07pd0897

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, journalists and photographers ask Japanese astronaut Takao Doi about the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module, or JEM, that he will accompany on mission STS-123 to the International Space Station. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the logistics module. The logistics module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

The NASA planetary biology internship experience

NASA Technical Reports Server (NTRS)

Hinkle, G.; Margulis, L.

1991-01-01

By providing students from around the world with the opportunity to work with established scientists in the fields of biogeochemistry, remote sensing, and origins of life, among others, the NASA Planetary Biology Internship (PBI) Program has successfully launched many scientific careers. Each year approximately ten interns participate in research related to planetary biology at NASA Centers, NASA-sponsored research in university laboratories, and private institutions. The PBI program also sponsors three students every year in both the Microbiology and Marine Ecology summer courses at the Marine Biological Laboratory. Other information about the PBI Program is presented including application procedure.

Incorporating C60 as Nucleation Sites Optimizing PbI2 Films To Achieve Perovskite Solar Cells Showing Excellent Efficiency and Stability via Vapor-Assisted Deposition Method.

PubMed

Chen, Hai-Bin; Ding, Xi-Hong; Pan, Xu; Hayat, Tasawar; Alsaedi, Ahmed; Ding, Yong; Dai, Song-Yuan

2018-01-24

To achieve high-quality perovskite solar cells (PSCs), the morphology and carrier transportation of perovskite films need to be optimized. Herein, C 60 is employed as nucleation sites in PbI 2 precursor solution to optimize the morphology of perovskite films via vapor-assisted deposition process. Accompanying the homogeneous nucleation of PbI 2 , the incorporation of C 60 as heterogeneous nucleation sites can lower the nucleation free energy of PbI 2 , which facilitates the diffusion and reaction between PbI 2 and organic source. Meanwhile, C 60 could enhance carrier transportation and reduce charge recombination in the perovskite layer due to its high electron mobility and conductivity. In addition, the grain sizes of perovskite get larger with C 60 optimizing, which can reduce the grain boundaries and voids in perovskite and prevent the corrosion because of moisture. As a result, we obtain PSCs with a power conversion efficiency (PCE) of 18.33% and excellent stability. The PCEs of unsealed devices drop less than 10% in a dehumidification cabinet after 100 days and remain at 75% of the initial PCE during exposure to ambient air (humidity > 60% RH, temperature > 30 °C) for 30 days.

Development and application of a general plasmid reference material for GMO screening.

PubMed

Wu, Yuhua; Li, Jun; Wang, Yulei; Li, Xiaofei; Li, Yunjing; Zhu, Li; Li, Jun; Wu, Gang

The use of analytical controls is essential when performing GMO detection through screening tests. Additionally, the presence of taxon-specific sequences is analyzed mostly for quality control during GMO detection. In this study, 11 commonly used genetic elements involving three promoters (P-35S, P-FMV35S and P-NOS), four marker genes (Bar, NPTII, HPT and Pmi), and four terminators (T-NOS, T-35S, T-g7 and T-e9), together with the reference gene fragments from six major crops of maize, soybean, rapeseed, rice, cotton and wheat, were co-integrated into the same single plasmid to construct a general reference plasmid pBI121-Screening. The suitability test of pBI121-Screening plasmid as reference material indicated that the non-target sequence on the pBI121-Screening plasmid did not affect the PCR amplification efficiencies of screening methods and taxon-specific methods. The sensitivity of screening and taxon-specific assays ranged from 5 to 10 copies of pBI121-Screening plasmid, meeting the sensitivity requirement of GMO detection. The construction of pBI121-Screening solves the lack of a general positive control for screening tests, thereby reducing the workload and cost of preparing a plurality of the positive control. Copyright © 2016 Elsevier B.V. All rights reserved.

KSC-07pd0633

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- At the Trident wharf, workers help guide the container with the Experiment Logistics Module Pressurized Section inside toward a flat bed on the dock. The logistics module is part of the Japanese Experiment Module. The logistics module will be transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0634

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- At the Trident wharf, workers help guide the container with the Experiment Logistics Module Pressurized Section inside onto a flat bed on the dock. The logistics module is part of the Japanese Experiment Module. The logistics module will be transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

Partial breast irradiation for early breast cancer.

PubMed

Hickey, Brigid E; Lehman, Margot; Francis, Daniel P; See, Adrienne M

2016-07-18

Breast-conserving therapy for women with breast cancer consists of local excision of the tumour (achieving clear margins) followed by radiotherapy (RT). RT is given to sterilize tumour cells that may remain after surgery to decrease the risk of local tumour recurrence. Most true recurrences occur in the same quadrant as the original tumour. Whole breast radiotherapy (WBRT) may not protect against the development of a new primary cancer developing in other quadrants of the breast. In this Cochrane review, we investigated the delivery of radiation to a limited volume of the breast around the tumour bed (partial breast irradiation (PBI)) sometimes with a shortened treatment duration (accelerated partial breast irradiation (APBI)). To determine whether PBI/APBI is equivalent to or better than conventional or hypo-fractionated WBRT after breast-conserving therapy for early-stage breast cancer. We searched the Cochrane Breast Cancer Group Specialized Register (4 May 2015), the Cochrane Central Register of Controlled Trials (CENTRAL) (2015, Issue 5), MEDLINE (January 1966 to 4 May 2015), EMBASE (1980 to 4 May 2015), CINAHL (4 May 2015) and Current Contents (4 May 2015). We searched the International Standard Randomised Controlled Trial Number Register (5 May 2015), the World Health Organization's International Clinical Trials Registry Platform (4 May 2015) and ClinicalTrials.gov (17 June 2015). We searched for grey literature: OpenGrey (17 June 2015), reference lists of articles, several conference proceedings and published abstracts, and applied no language restrictions. Randomized controlled trials (RCTs) without confounding, that evaluated conservative surgery plus PBI/APBI versus conservative surgery plus WBRT. Published and unpublished trials were eligible. Two review authors (BH and ML) performed data extraction and used Cochrane's 'Risk of bias' tool, and resolved any disagreements through discussion. We entered data into Review Manager 5 for analysis. We included seven RCTs and studied 7586 women of the 8955 enrolled.Local recurrence-free survival appeared worse for women receiving PBI/APBI compared to WBRT (hazard ratio (HR) 1.62, 95% confidence interval (CI) 1.11 to 2.35; six studies, 6820 participants, low-quality evidence). Cosmesis (physician-reported) appeared worse with PBI/APBI (odds ratio (OR) 1.51, 95% CI 1.17 to 1.95, five studies, 1720 participants, low-quality evidence). Overall survival did not differ with PBI/APBI (HR 0.90, 95% CI 0.74 to 1.09, five studies, 6718 participants, high-quality evidence).Late radiation toxicity (subcutaneous fibrosis) appeared worse with PBI/APBI (OR 6.58, 95% CI 3.08 to 14.06, one study, 766 participants, moderate-quality evidence). Acute skin toxicity appeared reduced with PBI/APBI (OR 0.04, 95% CI 0.02 to 0.09, two studies, 608 participants). Telangiectasia (OR 26.56, 95% CI 3.59 to 196.51, 1 study, 766 participants) and radiological fat necrosis (OR 1.58, 95% CI 1.02 to 2.43, three studies, 1319 participants) appeared worse with PBI/APBI. Late skin toxicity (OR 0.21, 95% CI 0.01 to 4.39, two studies, 608 participants) and breast pain (OR 2.17, 95% CI 0.56 to 8.44, one study, 766 participants) appeared not to differ with PBI/APBI.'Elsewhere primaries' (new primaries in the ipsilateral breast) appeared more frequent with PBI/APBI (OR 3.97, 95% CI 1.51 to 10.41, three studies, 3009 participants).We found no clear evidence of a difference for the comparison of PBI/APBI with WBRT for the outcomes of: cause-specific survival (HR 1.08, 95% CI 0.73 to 1.58, five studies, 6718 participants, moderate-quality evidence), distant metastasis-free survival (HR 0.94, 95% CI 0.65 to 1.37, four studies, 3267 participants, moderate-quality evidence), relapse-free survival (HR 1.36, 95% CI 0.88 to 2.09, three studies, 3811 participants), loco-regional recurrence-free survival (HR 1.80, 95% CI 1.00 to 3.25, two studies, 3553 participants) or mastectomy rates (OR 1.20, 95% CI 0.77 to 1.87, three studies, 4817 participants, low-quality evidence). Compliance was met: more than 90% of the women in all studies received the RT they were assigned to receive. We found no data for the outcomes of costs, quality of life or consumer preference. It appeared that local recurrence and 'elsewhere primaries' (new primaries in the ipsilateral breast) are increased with PBI/APBI (the difference was small), but we found no evidence of detriment to other oncological outcomes. It appeared that cosmetic outcomes and some late effects were worse with PBI/APBI but its use was associated with less acute skin toxicity. The limitations of the data currently available mean that we cannot make definitive conclusions about the efficacy and safety or ways to deliver of PBI/APBI. We await completion of ongoing trials.

Molecular cloning and characterization of satellite DNA sequences from constitutive heterochromatin of the habu snake (Protobothrops flavoviridis, Viperidae) and the Burmese python (Python bivittatus, Pythonidae).

PubMed

Matsubara, Kazumi; Uno, Yoshinobu; Srikulnath, Kornsorn; Seki, Risako; Nishida, Chizuko; Matsuda, Yoichi

2015-12-01

Highly repetitive DNA sequences of the centromeric heterochromatin provide valuable molecular cytogenetic markers for the investigation of genomic compartmentalization in the macrochromosomes and microchromosomes of sauropsids. Here, the relationship between centromeric heterochromatin and karyotype evolution was examined using cloned repetitive DNA sequences from two snake species, the habu snake (Protobothrops flavoviridis, Crotalinae, Viperidae) and Burmese python (Python bivittatus, Pythonidae). Three satellite DNA (stDNA) families were isolated from the heterochromatin of these snakes: 168-bp PFL-MspI from P. flavoviridis and 196-bp PBI-DdeI and 174-bp PBI-MspI from P. bivittatus. The PFL-MspI and PBI-DdeI sequences were localized to the centromeric regions of most chromosomes in the respective species, suggesting that the two sequences were the major components of the centromeric heterochromatin in these organisms. The PBI-MspI sequence was localized to the pericentromeric region of four chromosome pairs. The PFL-MspI and the PBI-DdeI sequences were conserved only in the genome of closely related species, Gloydius blomhoffii (Crotalinae) and Python molurus, respectively, although their locations on the chromosomes were slightly different. In contrast, the PBI-MspI sequence was also in the genomes of P. molurus and Boa constrictor (Boidae), and additionally localized to the centromeric regions of eight chromosome pairs in B. constrictor, suggesting that this sequence originated in the genome of a common ancestor of Pythonidae and Boidae, approximately 86 million years ago. The three stDNA sequences showed no genomic compartmentalization between the macrochromosomes and microchromosomes, suggesting that homogenization of the centromeric and/or pericentromeric stDNA sequences occurred in the macrochromosomes and microchromosomes of these snakes.

Facile hydrothermal synthesis and characterization of cesium-doped PbI2 nanostructures for optoelectronic, radiation detection and photocatalytic applications

NASA Astrophysics Data System (ADS)

Shkir, Mohd; AlFaify, S.; Yahia, I. S.; Hamdy, Mohamed S.; Ganesh, V.; Algarni, H.

2017-10-01

Low-temperature hydrothermal-assisted synthesis of pure and cesium (Cs) (1, 3, 5, 7 and 10 wt%) doped lead iodide (PbI2) nanorods and nanosheets have been achieved successfully for the first time. The structural and vibrational studies confirm the formation of a 2H-polytypic PbI2 predominantly. Scanning electron microscope analysis confirms the formation of well-aligned nanorods of average size 100 nm at low concentration and nanosheets of average thicknesses in the range of 20-40 nm at higher concentrations of Cs doping. The presence of Cs doping was confirmed by energy dispersive X-ray study. Ultra-violet-visible absorbance spectra were recorded, and energy gap was calculated in the range of 3.33 to 3.45 eV for pure and Cs-doped PbI2 nanostructures which is higher than the bulk value (i.e., 2.27 eV) due to quantum confinement effect. Dielectric constant, loss, and AC conductivity studies have been done. Enhancement in Gamma linear absorption coefficient due to Cs doping confirms the suitability of prepared nanostructures for radiation detection applications. Furthermore, the photocatalytic performance of the synthesized nanostructures was evaluated in the decolorization of methyl green (MG) and methyl orange (MO) under the illumination of visible light (λ > 420 nm). The observed photocatalytic activity for 5 and 7 wt% Cs-doped PbI2 was observed to be more than pure PbI2 and also > 10 times higher than the commercially available photocatalysts. The results suggest that the prepared nanostructures are highly applicable in optoelectronic, radiation detection and many other applications. [Figure not available: see fulltext.

Japanese Experiment Module arrival

NASA Image and Video Library

2007-03-29

Inside the Space Station Processing Facility, workers monitor progress as a huge crane is used to remove the top of the crate carrying the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

Japanese Experiment Module arrival

NASA Image and Video Library

2007-03-29

Inside the Space Station Processing Facility, the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module is revealed after the top of the crate is removed. The logistics module is one of the components of the Japanese Experiment Module or JEM, also known as Kibo, which means "hope" in Japanese. Kibo comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007.

Single crystalline CH 3NH 3PbI 3 self-grown on FTO/TiO 2 substrate for high efficiency perovskite solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Jinjin; Kong, Guoli; Chen, Shulin

In this work, we developed an innovative approach to self-grow single crystalline CH 3NH 3PbI 3 directly on polycrystalline FTO/TiO 2 substrate, with which n-i-p type of perovskite solar cells were fabricated. The single crystalline nature of CH 3NH 3PbI 3 has been confirmed by X-ray diffraction and high resolution transmission electron microscopy, and it is observed that they possess smaller optic band gap and longer carrier life time. Highly efficient charge extractions occur at the interface between electron collecting TiO 2 and photo-harvesting CH 3NH 3PbI 3, resulting in a maximum short-circuit current density of 24.40 mA/cm 2. Themore » champion cell possesses a photovoltaic conversion efficiency of 8.78%, and there are still substantial room for further improvement, making it promising for the perovskite solar cell applications.« less

Photoemission Spectroscopy Studies of Methylammonium Lead Iodide Perovskite Thin Films and Interfaces

NASA Astrophysics Data System (ADS)

Thibau, Emmanuel S.

Organometal halide perovskites have recently emerged as promising materials for fundamentally low-cost, high-performance optoelectronics. In this thesis, we utilize thermal co-evaporation of PbI2 and CH3NH 3 I to fabricate thin films of CH3NH3PbI 3. We first investigate the effect of stoichiometry on some of its structural, optical and electronic properties. Then, we study the energy level alignment of CH3NH3PbI3 with 6 organic semiconductors, revealing good agreement between the data and the theory of vacuum level alignment. Finally, the interface formed between CH3NH 3PbI3 and MoO3 is examined. The findings suggest migration of iodide species into the oxide layer, resulting in deterioration of its chemical and electronic properties. Insertion of an organic interlayer is shown to mitigate these undesirable effects. The results of this work could be of use in device engineering, where knowledge of such interfacial phenomena is of utmost importance in achieving optimized device structures.

Development of an improved coating for polybenzimidazole foam. [for space shuttle heat shields

NASA Technical Reports Server (NTRS)

Neuner, G. J.; Delano, C. B.

1976-01-01

An improved coating system was developed for Polybenzimidazole (PBI) foam to provide coating stability, ruggedness, moisture resistance, and to satisfy optical property requirements (alpha sub (s/epsilon) or = 0.4 and epsilon 0.8) for the space shuttle. The effort was performed in five tasks: Task 1 to establish material and process specifications for the PBI foam, and material specifications for the coatings; Task 2 to identify and evaluate promising coatings; Task 3 to establish mechanical and thermophysical properties of the tile components; Task 4 to determine by systems analysis the potential weight trade-offs associated with a coated PBI TPS; and Task 5 to establish a preliminary quality assurance program. The coated PBI tile was, through screening tests, determined to satisfy the design objectives with a reduced system weight over the baseline shuttle silica LRSI TPS. The developed tile provides a thermally stable, extremely rugged, low thermal conductivity insulator with a well characterized optical coating.

Single crystalline CH 3NH 3PbI 3 self-grown on FTO/TiO 2 substrate for high efficiency perovskite solar cells

DOE PAGES

Zhao, Jinjin; Kong, Guoli; Chen, Shulin; ...

2017-08-21

In this work, we developed an innovative approach to self-grow single crystalline CH 3NH 3PbI 3 directly on polycrystalline FTO/TiO 2 substrate, with which n-i-p type of perovskite solar cells were fabricated. The single crystalline nature of CH 3NH 3PbI 3 has been confirmed by X-ray diffraction and high resolution transmission electron microscopy, and it is observed that they possess smaller optic band gap and longer carrier life time. Highly efficient charge extractions occur at the interface between electron collecting TiO 2 and photo-harvesting CH 3NH 3PbI 3, resulting in a maximum short-circuit current density of 24.40 mA/cm 2. Themore » champion cell possesses a photovoltaic conversion efficiency of 8.78%, and there are still substantial room for further improvement, making it promising for the perovskite solar cell applications.« less

Superior Thermally Stable and Nonflammable Porous Polybenzimidazole Membrane with High Wettability for High-Power Lithium-Ion Batteries.

PubMed

Li, Dan; Shi, Dingqin; Xia, Yonggao; Qiao, Lin; Li, Xianfeng; Zhang, Huamin

2017-03-15

Separators with high security, reliability, and rate capacity are in urgent need for the advancement of high power lithium ion batteries. The currently used porous polyolefin membranes are critically hindered by their low thermal stability and poor electrolyte wettability, which further lead to low rate capacity. Here we present a novel promising porous polybenzimidazole (PBI) membrane with super high thermal stability and electrolyte wettability. The rigid structure and functional groups in the PBI chain enable membranes to be stable at temperature as high as 400 °C, and the unique flame resistance of PBI could ensure the high security of a battery as well. In particular, the prepared membrane owns 328% electrolyte uptake, which is more than two times higher than commercial Celgard 2325 separator. The unique combination of high thermal stability, high flame resistance and super high electrolyte wettability enable the PBI porous membranes to be highly promising for high power lithium battery.

Patterning and photoluminescent properties of perovskite-type organic/inorganic hybrid luminescent films by soft lithography

NASA Astrophysics Data System (ADS)

Cheng, Z. Y.; Wang, Z.; Xing, R. B.; Han, Y. C.; Lin, J.

2003-07-01

Perovskite-type organic/inorganic hybrid layered compound (C 6H 5C 2H 4NH 3) 2PbI 4 was synthesized. The patterning of (C 6H 5C 2H 4NH 3) 2PbI 4 thin films on silicon substrate was realized by the micromolding in capillaries (MIMIC) process, a kind of soft lithography. Bright green luminescent stripes with different widths (50, 15, 0.8 μm) have been obtained. The structure and optical properties of (C 6H 5C 2H 4NH 3) 2PbI 4 films were characterized by X-ray diffraction (XRD), UV/Vis absorption and photoluminescence excitation and emission spectra, respectively. It is shown that the organic-inorganic layered (C 6H 5C 2H 4NH 3) 2PbI 4 film was c-axis oriented, paralleling to the substrate plane. Green exciton emission at 525 nm was observed in the film, and the explanations for it were given.

CO2 Separation Using Thermally Optimized Membranes: A Comprehensive Project Report (2000 - 2007)

DOE Office of Scientific and Technical Information (OSTI.GOV)

J.R. Klaehn; C.J. Orme; E.S. Peterson

2008-03-01

This is a complete (Fiscal Years 2000–2006) collection of the Idaho National Laboratory’s (INL) research and development contributions to the project, “CO2 Separation Using Thermally Optimized Membranes.” The INL scientific contribution to the project has varied due to the fluctuations in funding from year to year. The focus of the project was polybenzimidazole (PBI) membranes and developing PBI compounds (both substitution and blends) that provide good film formation and gas separation membranes. The underlying problem with PBI is its poor solubility in common solvents. Typically, PBI is dissolved in “aggressive” solvents, like N,N-dimethylacetamide (DMAc) and N methylpyrrolidone (NMP). The INLmore » FY-03 research was directed toward making soluble N-substituted PBI polymers, where INL was very successful. Many different types of modified PBI polymers were synthesized; however, film formation proved to be a big problem with both unsubstituted and N-substituted PBIs. Therefore, INL researchers directed their attention to using plasticizers or additives to make the membranes more stable and workable. During the course of these studies, other high-performance polymers (like polyamides and polyimides) were found to be better materials, which could be used either by themselves or blends with PBI. These alternative high-performance polymers provided the best pathway forward for soluble high-temperature polymers with good stable film formation properties. At present, the VTEC polyimides (product of RBI, Inc.) are the best film formers that exhibit high-temperature resistance. INL’s gas testing results show VTEC polyimides have very good gas selectivities for both H2/CO2 and CO2/CH4. Overall, these high-performance polymers pointed towards new research areas where INL has gained a greater understanding of polymer film formation and gas separation. These studies are making possible a direct approach to stable polymer-based high-temperature gas separation membranes. This report is separated into several sections due to the complexity of the research and the variation with the development of better high-temperature, gas separation membranes. Several fiscal years are combined because the research and development efforts within those areas crossed fiscal year boundaries.« less

CO2 Separation Using Thermally Optimized Membranes: A Comprehensive Project Report (2000 - 2007)

DOE Office of Scientific and Technical Information (OSTI.GOV)

N /A

2008-03-04

This is a complete (Fiscal Years 2000–2006) collection of the Idaho National Laboratory’s (INL) research and development contributions to the project, “CO2 Separation Using Thermally Optimized Membranes.” The INL scientific contribution to the project has varied due to the fluctuations in funding from year to year. The focus of the project was polybenzimidazole (PBI) membranes and developing PBI compounds (both substitution and blends) that provide good film formation and gas separation membranes. The underlying problem with PBI is its poor solubility in common solvents. Typically, PBI is dissolved in “aggressive” solvents, like N,N-dimethylacetamide (DMAc) and N methylpyrrolidone (NMP). The INLmore » FY-03 research was directed toward making soluble N-substituted PBI polymers, where INL was very successful. Many different types of modified PBI polymers were synthesized; however, film formation proved to be a big problem with both unsubstituted and N-substituted PBIs. Therefore, INL researchers directed their attention to using plasticizers or additives to make the membranes more stable and workable. During the course of these studies, other high-performance polymers (like polyamides and polyimides) were found to be better materials, which could be used either by themselves or blends with PBI. These alternative high-performance polymers provided the best pathway forward for soluble high-temperature polymers with good stable film formation properties. At present, the VTEC polyimides (product of RBI, Inc.) are the best film formers that exhibit high-temperature resistance. INL’s gas testing results show VTEC polyimides have very good gas selectivities for both H2/CO2 and CO2/CH4. Overall, these high-performance polymers pointed towards new research areas where INL has gained a greater understanding of polymer film formation and gas separation. These studies are making possible a direct approach to stable polymer-based high-temperature gas separation membranes. This report is separated into several sections due to the complexity of the research and the variation with the development of better high-temperature, gas separation membranes. Several fiscal years are combined because the research and development efforts within those areas crossed fiscal year boundaries.« less

Evaluating complex health financing interventions: using mixed methods to inform further implementation of a novel PBI intervention in rural Malawi.

PubMed

McMahon, Shannon A; Brenner, Stephan; Lohmann, Julia; Makwero, Christopher; Torbica, Aleksandra; Mathanga, Don P; Muula, Adamson S; De Allegri, Manuela

2016-08-19

Gaps remain in understanding how performance-based incentive (PBI) programs affect quality of care and service quantity, whether programs are cost effective and how programs could be tailored to meet client and provider needs while remaining operationally viable. In 2014, Malawi's Ministry of Health launched the Service Delivery Integration-PBI (SSDI-PBI) program. The program is unique in that no portion of performance bonuses are paid to individual health workers, and it shifts responsibility for infrastructure and equipment procurement from facility staff to implementing partners. This protocol outlines an approach that analyzes processes and outcomes, considers expected and unexpected consequences of the program and frames the program's outputs relative to its costs. Findings from this evaluation will inform the intended future scale-up of PBI in Malawi. This study employs a prospective controlled before-and-after triangulation design to assess effects of the PBI program by analyzing quantitative and qualitative data from intervention and control facilities. Guided by a theoretical framework, the evaluation consists of four main components: service provision, health worker motivation, implementation processes and costing. Quality and access outcomes are assessed along four dimensions: (1) structural elements (related to equipment, drugs, staff); (2) process elements (providers' compliance with standards); (3) outputs (service utilization); (4) experiential elements (experiences of service delivery). The costing component includes costs related to start-up, ongoing management, and the cost of incentives themselves. The cost analysis considers costs incurred within the Ministry of Health, funders, and the implementing agency. The evaluation relies on primary data (including interviews and surveys) and secondary data (including costing and health management information system data). Through the lens of a PBI program, we illustrate how complex interventions can be evaluated via not only primary, mixed-methods data collection, but also through a wealth of secondary data from program implementers (including monitoring, evaluation and financial data), and the health system (including service utilization and service readiness data). We also highlight the importance of crafting a theory and using theory to inform the nature of data collected. Finally, we highlight the need to be responsive to stakeholders in order to enhance a study's relevance.

Polybenzimidazoles Via Aromatic Nucleophilic Displacement

NASA Technical Reports Server (NTRS)

Connell, John W. (Inventor); Hergerrother, Paul M. (Inventor); Smith, Joseph G., Jr. (Inventor)

1997-01-01

Novel molecular weight controlled and endcapped polybenzimidazoles (PBI) are prepared by the aromatic nucleophilic displacement reaction of di(hydroxyphenylbenzimidazole) monomers with activated aromatic dihalides or activated aromatic dinitro compounds. The PBI are endcapped with mono(hydroxyphenyl)benzimidazoles. The polymerizations are carried out in polar aprotic solvents such as N-methyl-2-pyrrolidinone or N,N-dimethylacetamide using alkali metal bases such as potassium carbonate at elevated temperatures under nitrogen. Mono(hydroxyphenyl)benzimidazoles are synthesized by reacting phenyl-4-hydroxybenzoate with aromatic (o-diamine)s in diphenylsulfone. Molecular weight controlled and endcapped PBI of new chemical structures are prepared that exhibit a favorable combination of physical and mechanical properties.

Polybenzimidazoles via aromatic nucleophilic displacement

NASA Technical Reports Server (NTRS)

Connell, John W. (Inventor); Hergenrother, Paul M. (Inventor); Smith, Joseph G., Jr. (Inventor)

1995-01-01

Novel molecular weight controlled and endcapped polybenzimidazoles (PBI) are prepared by the aromatic nucleophilic displacement reaction of di(hydroxyphenyl benzimidazole) monomers with activated aromatic dihalides or activated aromatic dinitro compounds. The PBI are endcapped with mono(hydroxyphenyl) benzimidazoles. The polymerizations are carried out in polar aprotic solvents such as N-methyl-2-pyrrolidinone or N,N-dimethylacetamide using alkali metal bases such as potassium carbonate at elevated temperatures under nitrogen. Mono(hydroxyphenyl) benzimidazoles are synthesizedby reacting phenyl-4-hydroxybenzoate with aromatic (o-diamine)s in diphenylsulfone. Molecular weight controlled and endcapped PBI of new chemical structures are prepared that exhibit a favorable combination of physical and mechanical properties.

Direct Observation of Excimer-Mediated Intramolecular Electron Transfer in a Cofacially-Stacked Perylene Bisimide Pair.

PubMed

Sung, Jooyoung; Nowak-Król, Agnieszka; Schlosser, Felix; Fimmel, Benjamin; Kim, Woojae; Kim, Dongho; Würthner, Frank

2016-07-27

We have elucidated excimer-mediated intramolecular electron transfer in cofacially stacked PBIs tethered by two phenylene-butadiynylene loops. The electron transfer between energetically equivalent PBIs is revealed by the simultaneous observation of the PBI radical anion and cation bands in the transient absorption spectra. The fluorescence decay time of the excimer states is in good agreement with the rise time of PBI radical bands in transient absorption spectra suggesting that the electron transfer dynamics proceed via the excimer state. We can conclude that the excimer state effectuates the efficient charge transfer in the cofacially stacked PBI dimer.

Flame retardant treatments of PBI fabric.

NASA Technical Reports Server (NTRS)

Temin, S. C.

1972-01-01

Fabrics knitted or woven from polybenzimidazole (PBI) fibers were treated to reduce flammability in oxygen atmospheres, particularly that of 5 psia oxygen. Bromination to approximately 15% weight gain of such fabrics led to markedly lower burning rates; samples brominated to over 80% weight gain were self-extinguishing in 5 psia oxygen. The loss in tensile strength of fabrics due to bromination was negligible although shrinkage was observed. Free fibers showed negligible losses on bromination. Treatment of PBI fabric with organophosphorus compounds also achieved self-extinguishing character in 5 psia oxygen but the enhanced flameproofing was largely lost on leaching. Reaction with POCl3 in pyridine led to a permanent reduction in flammability.

Enhanced photovoltaic performance of CH3NH3PbBrXI3-X-based perovskite solar cells via anti-solvent extraction

NASA Astrophysics Data System (ADS)

Jiang, Zhaoyi; Zhang, Weijia; Lu, Chaoqun; Ma, Denghao; Liu, Haixu; Yu, Wei; Zhang, Yu; Ma, Qiang; Zhang, Yulong

2018-06-01

In this paper, the two-step sequential deposition method was used to prepare the CH3NH3PbBrXI3-X films by introducing CH3NH3Br in the precursors. The surface morphology of the PbI2 films was controlled by anti-solvent extraction (ASE) to improve the microstructure and photo-physical properties of the perovskite films. It was noteworthy that, compared to the compact PbI2 films, the porous PbI2 films facilitated the growth of crystals and bromine incorporation in films, and the prepared perovskite films exhibited enlarged grain size, increased light absorption, enhanced Br incorporation and prolonged carrier lifetime, which resulted in excellent photo-electrical properties of the CH3NH3PbBrXI3-X films. With porous PbI2 templates, the inverted planar perovskite solar cells based on films with appropriate Br incorporation (CH3NH3Br/CH3NH3I mole ratio = 3/7) showed a photovoltaic conversion efficiency (PCE) of 14.9%, and the stability of the devices in air was elevated. Consequently, the high-quality CH3NH3PbBrXI3-X films can be obtained with porous PbI2 templates for improving the performance of the perovskite solar cells.

Tunable Crystallization and Nucleation of Planar CH3NH3PbI3 through Solvent-Modified Interdiffusion.

PubMed

Yao, Zhibo; Jones, Timothy W; Grigore, Mihaela; Duffy, Noel W; Anderson, Kenrick F; Dunbar, Ricky B; Feron, Krishna; Hao, Feng; Lin, Hong; Wilson, Gregory J

2018-05-02

A smooth and compact light absorption perovskite layer is a highly desirable prerequisite for efficient planar perovskite solar cells. However, the rapid reaction between CH 3 NH 3 I methylammonium iodide (MAI) and PbI 2 often leads to an inconsistent CH 3 NH 3 PbI 3 crystal nucleation and growth rate along the film depth during the two-step sequential deposition process. Herein, a facile solvent additive strategy is reported to retard the crystallization kinetics of perovskite formation and accelerate the MAI diffusion across the PbI 2 layer. It was found that the ultrasmooth perovskite thin film with narrow crystallite size variation can be achieved by introducing favorable solvent additives into the MAI solution. The effects of dimethylformamide, dimethyl sulfoxide, γ-butyrolactone, chlorobenzene, and diethyl ether additives on the morphological properties and cross-sectional crystallite size distribution were investigated using atomic force microscopy, X-ray diffraction, and scanning electron microscopy. Furthermore, the light absorption and band structure of the as-prepared CH 3 NH 3 PbI 3 films were investigated and correlated with the photovoltaic performance of the equivalent solar cell devices. Details of perovskite nucleation and crystal growth processes are presented, which opens new avenues for the fabrication of more efficient planar solar cell devices with these ultrasmooth perovskite layers.

Growth of CH3NH3PbI3 Perovskite on Stainless Steel Substrate Layered by ZnO Nanoparticles Using One-Step Spin Coating Route

NASA Astrophysics Data System (ADS)

Fuad, A.; Fibriyanti, A. A.; Mufti, N.; Taufiq, A.; Maryam, S.; Hidayat, N.

2018-04-01

In this work, we report the preparation of CH3NH3PbI3 perovskite using one-step spin coating route for solar cell application. CH3NH3I• PbI2•DMF•DMSO complexes were coated on stainless steel as a subtrate layered by ZnO nanoparticles as an electron transport layer. To obtain samples with a special performance, we annealed the samples at a temperature of 100, 120, and 140°C for 10 minutes. The samples were then characterized by means of XRD, SEM/EDX, and Spectroscopic Ellipsometry. The analysis of XRD data presented that the CH3NH3PbI3 perovskites were successfully prepared and crystallized in tetragonal structure confirming from crystalline planes (110) and (220). Meanwhile, the particle size of the samples prepared at a temperature of 100, 120, and 140°C presented 42.96, 54.73, and 55.19 nm, respectively with coincide with the SEM images. The results indicated that the increase in temperature during synthesis influenced the particle growth. Furthermore, the characterization using Spectroscopic Ellipsometry exhibited that the CH3NH3PbI3 successfully layered on the substrate sizing nano metric scale that open high opportunity to be applied to solar cells with high performance.

Perioperative Care for Pediatric Patients With Penetrating Brain Injury: A Review.

PubMed

Mikhael, Marco; Frost, Elizabeth; Cristancho, Maria

2017-05-19

Traumatic brain injury (TBI) continues to be the leading cause of death and acquired disability in young children and adolescents, due to blunt or penetrating trauma, the latter being less common but more lethal. Penetrating brain injury (PBI) has not been studied extensively, mainly reported as case reports or case series, due to the assumption that both types of brain injury have common pathophysiology and consequently common management. However, recommendations and guidelines for the management of PBI differ from those of blunt TBI in regards to neuroimaging, intracranial pressure (ICP) monitoring, and surgical management including those pertaining to vascular injury. PBI was one of the exclusion criteria in the second edition of guidelines for the acute medical management of severe TBI in infants, children, and adolescents that was published in 2012 (it is referred to as "pediatric guidelines" in this review). Many reviews of TBI do not differentiate between the mechanisms of injury. We present an overview of PBI, its presenting features, epidemiology, and causes as well as an analysis of case series and the conclusions that may be drawn from those and other studies. More clinical trials specific to penetrating head injuries in children, focusing mainly on pathophysiology and management, are needed. The term PBI is specific to penetrating injury only, whereas TBI, a more inclusive term, describes mainly, but not only, blunt injury.

Revealing the Self-Degradation Mechanisms in Methylammonium Lead Iodide Perovskites in Dark and Vacuum.

PubMed

Gunasekaran, Rajendra Kumar; Chinnadurai, Deviprasath; Selvaraj, Aravindha Raja; Rajendiran, Rajmohan; Senthil, Karuppanan; Prabakar, Kandasamy

2018-06-19

Organic-inorganic lead halide perovskite phases segregate (and their structures degrade) under illumination, exhibiting a poor stability with hysteresis and producing halide accumulation at the surface.In this work, we observed structural and interfacial dissociation in methylammonium lead iodide (CH 3 NH 3 PbI 3 ) perovskites even under dark and vacuum conditions. Here, we investigate the origin and consequences of self-degradation in CH 3 NH 3 PbI 3 perovskites stored in the dark under vacuum. Diffraction and photoelectron spectroscopic studies reveal the structural dissociation of perovskites into PbI 2 , which further dissociates into metallic lead (Pb 0 ) and I 2 - ions, collectively degrading the perovskite stability. Using TOF-SIMS analysis, AuI 2 - formation was directly observed, and it was found that an interplay between CH 3 NH 3 + , I 3 - , and mobile I - ions continuously regenerates more I 2 - ions, which diffuse to the surface even in the absence of light. Besides, halide diffusion causes a concentration gradient between Pb 0 and I 2 - and creates other ionic traps (PbI 2 - , PbI - ) that segregate as clusters at the perovskite/gold interface. A shift of the onset of the absorption band edge towards shorter wavelengths was also observed by absorption spectroscopy, indicating the formation of defect species upon aging in the dark under vacuum. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Variable sources for Cretaceous to recent HIMU and HIMU-like intraplate magmatism in New Zealand

NASA Astrophysics Data System (ADS)

van der Meer, Q. H. A.; Waight, T. E.; Scott, J. M.; Münker, C.

2017-07-01

Continental intraplate magmas with isotopic affinities similar to HIMU are identified worldwide. Involvement of an asthenospheric HIMU or HIMU-like source is contested because the characteristic radiogenic Pb compositions coupled with unradiogenic Sr and intermediate Nd and Hf compositions can also result from in-situ ingrowth in metasomatised lithospheric mantle. Sr-Nd-Pb-Hf isotopic compositions of late Cretaceous lamprophyre dikes from Westland, New Zealand, provide new insights into the formation of a HIMU-like alkaline intraplate magmatic province under the Zealandia continent. The oldest (102-100 Ma) calc-alkaline lamprophyres are compositionally similar to the preceding arc-magmatism (206Pb/204Pb(i) = 18.6, 207Pb/204Pb(i) = 15.62, 208Pb/204Pb(i) = 38.6, 87Sr/86Sr(i) = 0.7063-0.7074, εNd(i) = -2.1 - +0.1 and εHf(i) = -0.2 - +2.3) and are interpreted as melts originating from subduction-modified lithosphere. Alkaline dikes erupted on the inboard Gondwana margin shortly after cessation of subduction (92-84 Ma) have heterogeneous isotopic properties: 206Pb/204Pb(i) = 18.7 to 19.4, 207Pb/204Pb(i) = 15.60 to 15.65, 208Pb/204Pb(i) = 38.6 to 39.4, 87Sr/86Sr(i) = 0.7031 to 0.7068, εNd(i) = +4.5 to +8.0 and εHf(i) = +5.1 to +8.0. Melt compositions point to an amphibole-bearing spinel facies lithospheric mantle source enriched by metasomatism that introduced, amongst many elements, U + Th which lead to rapid ingrowth to HIMU-like compositions. Importantly, this HIMU-like source enrichment appears to have completely originated from the complex local subduction history. A coeval episode of alkaline magmatism (mainly 98-82 Ma) occurred outboard of Gondwana's former active margin and on the Hikurangi oceanic plateau (accreted to Zealandia in the Early Cretaceous) with compositions closer to true HIMU (206Pb/204Pb(i) ≈ 20.5, 207Pb/204Pb(i) ≈ 15.7, 208Pb/204Pb(i) ≈ 40.0, εNd(i) ≈ 4.5 and εHf(i) ≈ 4.0). In contrast to the inboard HIMU-like magmas, the radiogenic 207Pb/204Pb and relatively unradiogenic Nd and Hf require an ancient enriched source component. This magmatism is interpreted to represent melting of a fossilised HIMU source that resided under the Hikurangi Plateau. These genetically distinct but isotopically similar intraplate reservoirs were separated by the down-going slab under Gondwana's former active margin. Ancient HIMU magmatism was locally replaced by the young HIMU-like type which became dominant across Zealandia during the Late Cretaceous. Our research suggests that the sources for alkaline intraplate magmas with compositions similar to ocean island basalts can be formed either with or without the involvement of a plume-derived component.

Preservice Teachers' Conceptions and Enactments of Project-Based Instruction

ERIC Educational Resources Information Center

Marshall, Jill A.; Petrosino, Anthony J.; Martin, Taylor

2010-01-01

We present results of an investigation of preservice secondary mathematics and science teachers' conceptions of project-based instruction (PBI) and their enactments of PBI in apprentice (student) teaching. We evaluated their thinking and implementations within a composite framework based on the work of education researchers. We analyzed survey…

Training Bilingual Educators at a PBI

ERIC Educational Resources Information Center

Montes, Amanda Lira Gordenstein; Valenciano, Cynthia Kay; Fernandez, Miguel

2018-01-01

While Bilingual Education has traditionally been associated with linguistic diversity, the rise of the number of African-American teacher candidates in a Bilingual Education program at a mid-west Predominantly Black Institution (PBI) is causing the authors to reevaluate the input of this program's curriculum and the output of the candidates'…

An Instructional Theory for the Post-Industrial Age

ERIC Educational Resources Information Center

Reigeluth, Charles M.

2011-01-01

This article describes instructional theory that supports post-industrial education and training systems--ones that are customized and learner-centered, in which student progress is based on learning rather than time. The author discusses the importance of problem-based instruction (PBI), identifies some problems with PBI, overviews an…

Multi-Purpose Logistics Module Briefing

NASA Technical Reports Server (NTRS)

2001-01-01

Silvanna Rabbi, MPLM Program Manager, Italian Space Agency, gives an overview of the Multi-Purpose Logistics Module (MPLM) in a prelaunch press conference. She describes the objectives, construction, specifications, and purpose of the three Italian-built modules, Leonardo, Rafaello, and Donatello. Ms. Rabbi then answers questions from the press.

Physical punishment and signs of mental distress in normal adolescents.

PubMed

Bachar, E; Canetti, L; Bonne, O; DeNour, A K; Shalev, A Y

1997-01-01

Adolescents (375 males and 496 females) were administered the Brief Symptom Inventory (BSI), the General Well-Being Scale (GWB), the Parental Bonding Instrument (PBI), and two questions about each parent, supplementing the PBI, tapping violent punitive behavior. Signs of mental distress in adolescents and reported physical punishment from parents were analyzed. Results indicated that greater physical punishment was associated with higher levels of psychiatric symptoms and lower general well-being. These results persisted after controlling for parental attitudes, as quantified by the PBI, and socioeconomic status. The findings of this study can contribute to efforts to raise public awareness of the negative consequences of physical punishment on the mental health of children.

Enhanced Photovoltaic Performance of Perovskite Solar Cells by Copper Chloride (CuCl2) as an Additive in Single Solvent Perovskite Precursor

NASA Astrophysics Data System (ADS)

Emrul Kayesh, Md.; Matsuishi, Kiyoto; Chowdhury, Towhid H.; Kaneko, Ryuji; Noda, Takeshi; Islam, Ashraful

2018-05-01

In this letter, we have introduced copper chloride (CuCl2) as an additive in the CH3NH3PbI3 precursor solution to improve the surface morphology and crystallinity of CH3NH3PbI3 films in a single solvent system. Our optimized perovskite solar cells (PSCs) with 2.5 mol% CuCl2 additive showed best power conversion efficiency (PCE) of 15.22%. The PCE of the PSCs fabricated by CuCl2 (2.5 mol%) additive engineering was 56% higher than the PSC fabricated with pristine CH3NH3PbI3.

Multifunctional Diketopyrrolopyrrole-Based Conjugated Polymers with Perylene Bisimide Side Chains.

PubMed

Li, Cheng; Yu, Changshi; Lai, Wenbin; Liang, Shijie; Jiang, Xudong; Feng, Guitao; Zhang, Jianqi; Xu, Yunhua; Li, Weiwei

2017-11-24

Two conjugated polymers based on diketopyrrolopyrrole (DPP) in the main chain with different content of perylene bisimide (PBI) side chains are developed. The influence of PBI side chain on the photovoltaic performance of these DPP-based conjugated polymers is systematically investigated. This study suggests that the PBI side chains can not only alter the absorption spectrum and energy level but also enhance the crystallinity of conjugated polymers. As a result, such polymers can act as electron donor, electron acceptor, and single-component active layer in organic solar cells. These findings provide a new guideline for the future molecular design of multifunctional conjugated polymers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A Longitudinal Investigation of Project-Based Instruction and Student Achievement in High School Social Studies

ERIC Educational Resources Information Center

Summers, Emily J.; Dickinson, Gail

2012-01-01

This longitudinal study focused on how project-based instruction (PBI) influenced secondary social studies students' academic achievement and promoted College and Career Readiness (CCR). We explored and compared student achievement in a PBI high school versus a traditional instruction high school within the same rural school district. While…

Electron-acoustic phonon coupling in single crystal CH3NH3PbI3 perovskites revealed by coherent acoustic phonons

NASA Astrophysics Data System (ADS)

Mante, Pierre-Adrien; Stoumpos, Constantinos C.; Kanatzidis, Mercouri G.; Yartsev, Arkady

2017-02-01

Despite the great amount of attention CH3NH3PbI3 has received for its solar cell application, intrinsic properties of this material are still largely unknown. Mobility of charges is a quintessential property in this aspect; however, there is still no clear understanding of electron transport, as reported values span over three orders of magnitude. Here we develop a method to measure the electron and hole deformation potentials using coherent acoustic phonons generated by femtosecond laser pulses. We apply this method to characterize a CH3NH3PbI3 single crystal. We measure the acoustic phonon properties and characterize electron-acoustic phonon scattering. Then, using the deformation potential theory, we calculate the carrier intrinsic mobility and compare it to the reported experimental and theoretical values. Our results reveal high electron and hole mobilities of 2,800 and 9,400 cm2 V-1 s-1, respectively. Comparison with literature values of mobility demonstrates the potential role played by polarons in charge transport in CH3NH3PbI3.

Electroluminescence of organic light-emitting diodes consisting of an undoped (pbi)2Ir(acac) phosphorescent layer

NASA Astrophysics Data System (ADS)

Lei, Xia; Yu, Junsheng; Zhao, Juan; Jiang, Yadong

2011-11-01

The electroluminescence (EL) characteristics of phosphorescent organic light-emitting diodes (OLEDs) with an undoped bis(1,2-dipheny1-1H-benzoimidazole) iridium (acetylacetonate) [(pbi)2Ir(acac)] emissive layer (EML) of various film thicknesses were studied. The results showed that the intensity of green light emission decreased rapidly with the increasing thickness of (pbi)2Ir(acac), which was relevant to the triplet excimer emission. It suggested that the concentration quenching of monomer emission in the undoped (pbi)2Ir(acac) film was mainly due to the formation of triplet excimer and partly due to the triplet-triplet annihilation (TTA) and triplet-polaron annihilation (TPA). A green OLED with a maximum luminance of 26,531 cd/m2, a current efficiency of 36.2 cd/A, and a power efficiency of 32.4 lm/W was obtained, when the triplet excimer emission was eliminated. Moreover, the white OLED with low efficiency roll-off was realized due to the broadened recombination zone and reduced quenching effects in the EML when no electron blocking layer was employed.

Crack-free CH3NH3PbI3 layer via continuous dripping method for high-performance mesoporous perovskite solar cells

NASA Astrophysics Data System (ADS)

Chen, Guo; Zheng, Jianghui; Zheng, LingLing; Yan, Xin; Lin, Huangding; Zhang, Fengyan

2017-01-01

The past five years have witnessed the uniquely rapid emergence of the mixed organic-inorganic halide perovskite solar cells. Here, a modified deposition process, continuous dripping method, is reported for fabricating high-performance and reproducible perovskite solar cells. We have systematically investigated the impact of different molar ratio of lead iodide (PbI2) to dimethylsulfoxide (DMSO) on the growth, morphology and crystallinity of CH3NH3PbI3 (MAPbI3) films obtained via this process. The high power conversion efficiency (PCE) perovskite solar cell originates in crack-free and highly crystallographic perovskite films prepared with optimized ratio of PbI2 to DMSO in first precursor solution. The best PCE of 17.76% and an average PCE of 16.37 ± 0.51% were obtained via this process. Moreover, the conventional solution two steps method was also carried out as a comparison to this process. This work provides a new simple solution approach to obtain high quality of perovskite thin films for high-performance and reproducible PSCs.

Relationship between perceived body image and recorded body mass index among Kuwaiti female university students.

PubMed

Kabir, Yearul; Zafar, Tasleem A; Waslien, Carol

2013-01-01

The associations between body image and attitudes toward obesity and thinness and their associations with measured body mass index (BMI) among female students of Kuwait University (n = 137) was examined in 2008. The body image perceptions were assessed using nine female silhouettes figures. The difference between current perceived body image (PBI) and ideal body image (IBI) was used as a measure of body image dissatisfaction (BID). Students tended to have a bigger PBI and smaller IBI than would be expected from their BMI category, leading to high levels of BID in each BMI category. PBI, IBI, BID, RBI were highly correlated with each other, and BMI was significantly correlated with each of them. The coefficients of these associations were not significantly altered in multiple regression analysis by the addition of potential confounding variables, such as age, marital status, physical activity, dieting behavior, parental education, and family size. These results suggest that PBI and a desire to be thinner were strongly related to BID and that thinness is becoming more desired in Kuwaiti society than the plump body image of the past.

Role of organic cations on hybrid halide perovskite CH3NH3PbI3 surfaces

NASA Astrophysics Data System (ADS)

Teng, Qiang; Shi, Ting-Ting; Tian, Ren-Yu; Yang, Xiao-Bao; Zhao, Yu-Jun

2018-02-01

Organic-inorganic hybrid halide perovskite CH3NH3PbI3 (MAPbI3) has received rapid progress in power conversion efficiency as promising photovoltaic materials, yet the surface structures and the role of MA cations are not well understood. In this work, we investigated the structural stability and electronic properties of (001) surface of cubic, (001) and (110) surfaces of tetragonal and orthorhombic phases of MAPbI3 with considering the orientation of MA cations, by density functional theory calculations. We demonstrate that the orientation of MA cations has profound consequences on the structural stability and the electronic properties of the surfaces, in contrast to the bulk phases. Compared with the MA-I terminated surfaces, the Pb-I2 terminated ones generally have smaller band gaps and the advantage to enable the photo-excited holes to transfer to the hole-transport materials in both tetragonal and orthorhombic phases. Overall, we suggest that the films with Pb-I2 terminated surfaces would prevail in high performance solar energy absorbers.

Perovskite-based solar cells with inorganic inverted hybrid planar heterojunction structure

NASA Astrophysics Data System (ADS)

Lai, Wei-Chih; Lin, Kun-Wei; Guo, Tzung-Fang; Chen, Peter; Liao, Yuan-Yu

2018-01-01

We demonstrated the good performance of inorganic inverted CH3NH3PbI3 perovskite-based solar cells (SCs) with glass/ITO/NiOx/CH3NH3PbI3 perovskite/C60/ room temperature (RT)-sputtered ZnO/Al structure. We adopted spin coating and RT sputtering for the deposition of NiOx and ZnO, respectively. The inorganic hole and electron transport layer of NiOx and RT-sputtered ZnO, respectively, could improve the open-circuit voltage (VOC), short-circuit current density (JSC), and power conversion efficiency (η%) of the SCs. We obtained inorganic inverted CH3NH3PbI3 perovskite-based SCs with a JSC of 21.96 A/cm2, a VOC of 1.02 V, a fill factor (FF%) of 68.2%, and an η% of 15.3% despite the sputtering damage of the RT-sputtered ZnO deposition. Moreover, the RT-sputtered ZnO could function as a diffusion barrier for Al, moisture, and O2. The inorganic inverted CH3NH3PbI3 perovskite-based SCs demonstrated improved storage reliability.

Homogeneous Emission Line Broadening in the Organo Lead Halide Perovskite CH3NH3PbI3-xClx.

PubMed

Wehrenfennig, Christian; Liu, Mingzhen; Snaith, Henry J; Johnston, Michael B; Herz, Laura M

2014-04-17

The organic-inorganic hybrid perovskites methylammonium lead iodide (CH3NH3PbI3) and the partially chlorine-substituted mixed halide CH3NH3PbI3-xClx emit strong and broad photoluminescence (PL) around their band gap energy of ∼1.6 eV. However, the nature of the radiative decay channels behind the observed emission and, in particular, the spectral broadening mechanisms are still unclear. Here we investigate these processes for high-quality vapor-deposited films of CH3NH3PbI3-xClx using time- and excitation-energy dependent photoluminescence spectroscopy. We show that the PL spectrum is homogenously broadened with a line width of 103 meV most likely as a consequence of phonon coupling effects. Further analysis reveals that defects or trap states play a minor role in radiative decay channels. In terms of possible lasing applications, the emission spectrum of the perovskite is sufficiently broad to have potential for amplification of light pulses below 100 fs pulse duration.

Electron-hole diffusion lengths >175 μm in solution-grown CH 3NH 3PbI 3 single crystals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong, Qingfeng; Fang, Yanjun; Shao, Yuchuan

Long, balanced electron and hole diffusion lengths greater than 100 nanometers in the polycrystalline organolead trihalide compound CH 3NH 3PbI 3 are critical for highly efficient perovskite solar cells. We found that the diffusion lengths in CH 3NH 3PbI 3 single crystals grown by a solution-growth method can exceed 175 micrometers under 1 sun (100 mW cm –2) illumination and exceed 3 millimeters under weak light for both electrons and holes. The internal quantum efficiencies approach 100% in 3-millimeter-thick single-crystal perovskite solar cells under weak light. These long diffusion lengths result from greater carrier mobility, longer lifetime, and much smallermore » trap densities in the single crystals than in polycrystalline thin films. As a result, the long carrier diffusion lengths enabled the use of CH 3NH 3PbI 3 in radiation sensing and energy harvesting through the gammavoltaic effect, with an efficiency of 3.9% measured with an intense cesium-137 source.« less

Electron-hole diffusion lengths >175 μm in solution-grown CH 3NH 3PbI 3 single crystals

DOE PAGES

Dong, Qingfeng; Fang, Yanjun; Shao, Yuchuan; ...

2015-02-27

Long, balanced electron and hole diffusion lengths greater than 100 nanometers in the polycrystalline organolead trihalide compound CH 3NH 3PbI 3 are critical for highly efficient perovskite solar cells. We found that the diffusion lengths in CH 3NH 3PbI 3 single crystals grown by a solution-growth method can exceed 175 micrometers under 1 sun (100 mW cm –2) illumination and exceed 3 millimeters under weak light for both electrons and holes. The internal quantum efficiencies approach 100% in 3-millimeter-thick single-crystal perovskite solar cells under weak light. These long diffusion lengths result from greater carrier mobility, longer lifetime, and much smallermore » trap densities in the single crystals than in polycrystalline thin films. As a result, the long carrier diffusion lengths enabled the use of CH 3NH 3PbI 3 in radiation sensing and energy harvesting through the gammavoltaic effect, with an efficiency of 3.9% measured with an intense cesium-137 source.« less

Planar-Structure Perovskite Solar Cells with Efficiency beyond 21.

PubMed

Jiang, Qi; Chu, Zema; Wang, Pengyang; Yang, Xiaolei; Liu, Heng; Wang, Ye; Yin, Zhigang; Wu, Jinliang; Zhang, Xingwang; You, Jingbi

2017-12-01

Low temperature solution processed planar-structure perovskite solar cells gain great attention recently, while their power conversions are still lower than that of high temperature mesoporous counterpart. Previous reports are mainly focused on perovskite morphology control and interface engineering to improve performance. Here, this study systematically investigates the effect of precise stoichiometry, especially the PbI 2 contents on device performance including efficiency, hysteresis and stability. This study finds that a moderate residual of PbI 2 can deliver stable and high efficiency of solar cells without hysteresis, while too much residual PbI 2 will lead to serious hysteresis and poor transit stability. Solar cells with the efficiencies of 21.6% in small size (0.0737 cm 2 ) and 20.1% in large size (1 cm 2 ) with moderate residual PbI 2 in perovskite layer are obtained. The certificated efficiency for small size shows the efficiency of 20.9%, which is the highest efficiency ever recorded in planar-structure perovskite solar cells, showing the planar-structure perovskite solar cells are very promising. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fabrication of efficient planar perovskite solar cells using a one-step chemical vapor deposition method

PubMed Central

Tavakoli, Mohammad Mahdi; Gu, Leilei; Gao, Yuan; Reckmeier, Claas; He, Jin; Rogach, Andrey L.; Yao, Yan; Fan, Zhiyong

2015-01-01

Organometallic trihalide perovskites are promising materials for photovoltaic applications, which have demonstrated a rapid rise in photovoltaic performance in a short period of time. We report a facile one-step method to fabricate planar heterojunction perovskite solar cells by chemical vapor deposition (CVD), with a solar power conversion efficiency of up to 11.1%. We performed a systematic optimization of CVD parameters such as temperature and growth time to obtain high quality films of CH3NH3PbI3 and CH3NH3PbI3-xClx perovskite. Scanning electron microscopy and time resolved photoluminescence data showed that the perovskite films have a large grain size of more than 1 micrometer, and carrier life-times of 10 ns and 120 ns for CH3NH3PbI3 and CH3NH3PbI3-xClx, respectively. This is the first demonstration of a highly efficient perovskite solar cell using one step CVD and there is likely room for significant improvement of device efficiency. PMID:26392200

Origin of High Electronic Quality in Solar Cell Absorber CH3NH3PbI3

NASA Astrophysics Data System (ADS)

Yin, Wanjian; Shi, Tingting; Wei, Suhua; Yan, Yanfa

Thin-film solar cells based on CH3NH3PbI3 halide perovskites have recently shown remarkable performance. First-principle calculations and molecular dynamic simulations show that the structure of pristine CH3NH3PbI3 is much more disordered than the inorganic archetypal thin-film semiconductor CdTe. However, the structural disorders from thermal fluctuation, point defects and grain boundaries introduce rare deep defect states within the bandgaps; therefore, the material has high electronic quality. We have further shown that this unusually high electronic quality is attributed to the unique electronic structures of halide perovskite: the strong coupling between cation lone-pair Pb s orbitals and anion p orbitals and the large atomic size of constitute cation atoms. We further found that although CH3NH3PbI3 GBs do not introduce a deep gap state, the defect level close to the VBM can still act as a shallow hole trap state. Cl and O can spontaneously segregate into GBs and passivate those defect levels and deactivate the trap state.

Unveiling the irreversible performance degradation of organo-inorganic halide perovskite films and solar cells during heating and cooling processes.

PubMed

Mamun, Abdullah Al; Ava, Tanzila Tasnim; Byun, Hye Ryung; Jeong, Hyeon Jun; Jeong, Mun Seok; Nguyen, Loi; Gausin, Christine; Namkoong, Gon

2017-07-26

While organo-inorganic halide perovskite solar cells show great potential to meet future energy needs, their thermal instability raises serious questions about their commercialization viability. At present, the stability of perovskite solar cells has been studied under various environmental conditions including humidity and temperature. Nonetheless, understanding of the performance of CH 3 NH 3 PbI 3-x Cl x perovskite solar cells is limited. This study reports the irreversible performance degradation of CH 3 NH 3 PbI 3-x Cl x perovskite solar cells during the heating and cooling processes under AM 1.5 and unveils what triggers the irreversible performance degradation of solar cells. Particularly, the primary cause of the irreversible performance degradation of CH 3 NH 3 PbI 3-x Cl x is quantitatively analyzed by monitoring in real time the development of deteriorated crystallinity, charge trapping/detrapping, trap depth, and the PbI 2 phase, namely a critical signal of perovskite degradation while varying the temperature of the perovskite films and solar cells. Most surprisingly, it is revealed that the degradation of both perovskite films and solar cells was triggered at ∼70 °C. Remarkably, even after the device temperature cooled down to room temperature, the degraded performance of the solar cells persisted with increasing charge trapping and further development of the PbI 2 phase. Identification of the irreversible performance degradation of perovskite solar cells provides guidance for future development of more stable perovskite solar cells.

Preoperative single fraction partial breast radiotherapy for early-stage breast cancer.

PubMed

Palta, Manisha; Yoo, Sua; Adamson, Justus D; Prosnitz, Leonard R; Horton, Janet K

2012-01-01

Several recent series evaluating external beam accelerated partial breast irradiation (PBI) have reported adverse cosmetic outcomes, possibly related to large volumes of normal tissue receiving near-prescription doses. We hypothesized that delivery of external beam PBI in a single fraction to the preoperative tumor volume would be feasible and result in a decreased dose to the uninvolved breast compared with institutional postoperative PBI historical controls. A total of 17 patients with unifocal Stage T1 breast cancer were identified. Contrast-enhanced subtraction magnetic resonance images were loaded into an Eclipse treatment planning system and used to define the target volumes. A "virtual plan" was created using four photon beams in a noncoplanar beam arrangement and optimized to deliver 15 Gy to the planning target volume. The median breast volume was 1,713 cm(3) (range: 1,014-2,140), and the median clinical target volume was 44 cm(3) (range: 26-73). In all cases, 100% of the prescription dose covered 95% of the clinical target volume. The median conformity index was 0.86 (range: 0.70-1.12). The median percentage of the ipsilateral breast volume receiving 100% and 50% of the prescribed dose was 3.8% (range: 2.2-6.9) and 13.3% (range: 7.5-20.8) compared with 18% (range: 3-42) and 53% (range: 24-65) in the institutional historical controls treated with postoperative external beam PBI (p = .002). The median maximum skin dose was 9 Gy. The median dose to 1 and 10 cm(3) of skin was 6.7 and 4.9 Gy. The doses to the heart and ipsilateral lung were negligible. Preoperative PBI resulted in a substantial reduction in ipsilateral breast tissue dose compared with postoperative PBI. The skin dose appeared reasonable, given the small volumes. A prospective Phase I trial evaluating this technique is ongoing. Copyright © 2012 Elsevier Inc. All rights reserved.

Face and location processing in children with early unilateral brain injury.

PubMed

Paul, Brianna; Appelbaum, Mark; Carapetian, Stephanie; Hesselink, John; Nass, Ruth; Trauner, Doris; Stiles, Joan

2014-07-01

Human visuospatial functions are commonly divided into those dependent on the ventral visual stream (ventral occipitotemporal regions), which allows for processing the 'what' of an object, and the dorsal visual stream (dorsal occipitoparietal regions), which allows for processing 'where' an object is in space. Information about the development of each of the two streams has been accumulating, but very little is known about the effects of injury, particularly very early injury, on this developmental process. Using a set of computerized dorsal and ventral stream tasks matched for stimuli, required response, and difficulty (for typically-developing individuals), we sought to compare the differential effects of injury to the two systems by examining performance in individuals with perinatal brain injury (PBI), who present with selective deficits in visuospatial processing from a young age. Thirty participants (mean=15.1 years) with early unilateral brain injury (15 right hemisphere PBI, 15 left hemisphere PBI) and 16 matched controls participated. On our tasks children with PBI performed more poorly than controls (lower accuracy and longer response times), and this was particularly prominent for the ventral stream task. Lateralization of PBI was also a factor, as the dorsal stream task did not seem to be associated with lateralized deficits, with both PBI groups showing only subtle decrements in performance, while the ventral stream task elicited deficits from RPBI children that do not appear to improve with age. Our findings suggest that early injury results in lesion-specific visuospatial deficits that persist into adolescence. Further, as the stimuli used in our ventral stream task were faces, our findings are consistent with what is known about the neural systems for face processing, namely, that they are established relatively early, follow a comparatively rapid developmental trajectory (conferring a vulnerability to early insult), and are biased toward the right hemisphere. Copyright © 2014 Elsevier Inc. All rights reserved.

The influence of the utilization time of brush heads from different types of power toothbrushes on oral hygiene assessed over a 6-month observation period: A randomized clinical trial.

PubMed

Schmickler, Jan; Wurbs, Sabine; Wurbs, Susanne; Kramer, Katharina; Rinke, Sven; Hornecker, Else; Mausberg, Rainer F; Ziebolz, Dirk

2016-12-01

This randomized clinical trial investigated the influence of the utilization time of brush heads from different types of power toothbrushes [oscillating rotating (OR) and sonic action (SA)93; on oral hygiene (plaque accumulation and gingival inflammation) over a 6-month observation period. 49 participants were randomly allocated into two groups: use of the same brush head over 6 months (NR: non-replacement) or replacement of brush head every 4 weeks over 6 months (R: replacement). Each group was subdivided into two subgroups according to kind of toothbrush (TB) used (OR and SA). Modified Quigley-Hein plaque index (QHI), papilla bleeding index (PBI), and gingival index (GI) were recorded at baseline and 2, 8, 12, 16, and 24 weeks after baseline. After 24 weeks, participants of both groups (R and NR) received a new brush head. At week 26, final QHI, PBI, and GI were recorded. QHI decreased between baseline and follow-up visits in R groups (P< 0.05), with the exception of week 12 (P= 0.26). In NR groups, no significant decrease was detected (P> 0.05). There was no significant effect of time on PBI or GI in any of R subgroups (P> 0.05). In NR oscillating/rotating TB: significant increase in PBI and GI was detected 24 weeks after baseline (PBI: P= 0.02, GI: P= 0.03); sonic action TBs showed significant decrease in PBI at every follow-up visit (P< 0.05), except at 24 weeks after baseline (P= 0.73). GI was significantly decreased at 2 weeks after baseline only (P< 0.01). Six-month use of the same brush head reduced effectiveness in removing plaque, and gingival inflammation appeared to increase after a utilization time of over 4 months. Replacing brush heads is advised after 4 months.

KSC-07pd0626

NASA Image and Video Library

2007-03-12

KENNEDY SPACE CENTER, FLA. -- The ship carrying the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module arrives at the Trident wharf after departing from Yokohama, Japan, Feb. 7. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0628

NASA Image and Video Library

2007-03-12

KENNEDY SPACE CENTER, FLA. -- The ship carrying the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module arrives at the Trident wharf after departing from Yokohama, Japan, Feb. 7. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0627

NASA Image and Video Library

2007-03-12

KENNEDY SPACE CENTER, FLA. -- The ship carrying the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module arrives at the Trident wharf after departing from Yokohama, Japan, Feb. 7. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0629

NASA Image and Video Library

2007-03-12

KENNEDY SPACE CENTER, FLA. -- The ship carrying the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module is tied up at the Trident wharf after departing from Yokohama, Japan, Feb. 7. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

KSC-07pd0631

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- At the Trident wharf, workers in the hold of a ship attach a crane to the shipping container with the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module. The ship brought the module from Yokohama, Japan. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

The Impact of Different Instructions on Vietnamese EFL Students' Acquisition of Formulaic Sequences

ERIC Educational Resources Information Center

Ha, Do Thi

2017-01-01

The paper explores how various teaching methods, namely Phonology-Based Instruction (PBI) and Translation-Based Instruction (TBI), have an effect on students' acquisition of formulaic sequences. 20 multiword expressions were taught to 48 Vietnamese EFL students from three intact classes as 2 treatment groups (PBI and TBI) and 1 control group.…

Comprehension-Based versus Production-Based Grammar Instruction: A Meta-Analysis of Comparative Studies

ERIC Educational Resources Information Center

Shintani, Natsuko; Li, Shaofeng; Ellis, Rod

2013-01-01

This article reports a meta-analysis of studies that investigated the relative effectiveness of comprehension-based instruction (CBI) and production-based instruction (PBI). The meta-analysis only included studies that featured a direct comparison of CBI and PBI in order to ensure methodological and statistical robustness. A total of 35 research…

Species Boundaries and Interrelationships of Solanum Sect. Petota (Wild and Cultivated Potatoes) are Drastically Altered as a Result of PBI-Funded Research

USDA-ARS?s Scientific Manuscript database

In 1990, the latest comprehensive taxonomic monograph of Solanum section Petota Dumort, recognized 232 species partitioned into 21 series. PBI-sponsored research has drastically altered knowledge of their species boundaries and interrelationships. The series contains diploids (2n = 2x = 24), tetrapl...

Species Boundaries and Interrelationships of Solanum Sect. Petota (Wild and Cultivated Potatoes) are Drastically Altered as a Result of PBI-Funded Research

USDA-ARS?s Scientific Manuscript database

In 1990, the latest comprehensive taxonomic monograph of Solanum section Petota Dumort recognized 232 species partitioned into 21 series. PBI-sponsored research has drastically altered knowledge of their species boundaries and interrelationships. The series contains diploids (2n = 2x = 24), tetraplo...

Larger spontaneous polarization ferroelectric inorganic-organic hybrids: [PbI3](infinity) chains directed organic cations aggregation to Kagomé-shaped tubular architecture.

PubMed

Zhao, Hai-Rong; Li, Dong-Ping; Ren, Xiao-Ming; Song, You; Jin, Wan-Qin

2010-01-13

Four isostructural inorganic-organic hybrid ferroelectric compounds, assembled from achiral 3-R-benzylidene-1-aminopyridiniums (R = NO(2), Br, Cl, or F for 1-4, respectively) and [PbI(3)](-) anions with the chiral Kagomé-shaped tubular aggregating architecture, show larger spontaneous polarizations.

Ultrafine polybenzimidazole (PBI) fibers. [separators for alkaline batteries and dfuel cells

NASA Technical Reports Server (NTRS)

Chenevey, E. C.

1979-01-01

Mats were made from ultrafine polybenzimidazole (PBI) fibers to provide an alternate to the use of asbestos as separators in fuel cells and alkaline batteries. To minimize distortion during mat drying, a process to provide a dry fibrid was developed. Two fibrid types were developed: one coarse, making mats for battery separators; the other fine, making low permeability matrices for fuel cells. Eventually, it was demonstrated that suitable mat fabrication techniques yielded fuel cell separators from the coarser alkaline battery fibrids. The stability of PBI mats to 45% KOH at 123 C can be increased by heat treatment at high temperatures. Weight loss data to 1000 hours exposure show the alkali resistance of the mats to be superior to that of asbestos.

CH3NH3I treatment temperature of 70 °C in low-pressure vapor-assisted deposition for mesoscopic perovskite solar cells

NASA Astrophysics Data System (ADS)

Jin, Wenbin; Zou, Xiaoping; Bai, Xiao; Yang, Ying; Chen, Dan

2018-01-01

Herein, we report a modified vapor-assisted deposition method to fabricate CH3NH3PbI3 film at 70 °C in a vacuum drying oven. The modified method has excellent operability and expandability in preparing perovskite solar cells. The CH3NH3I treatment temperature is 130 °C or 150 °C in conventional method, but we reduced the temperature to 70 °C in the modified vapor-assisted method. Meanwhile, the quality of CH3NH3PbI3 films prepared via the modified method is superior to that of CH3NH3PbI3 films of solution-processed method.

An albumin nanocomplex-based endosomal pH-activatable on/off probe system.

PubMed

Lee, Changkyu; Lee, Seunghyun; Thao, Le Quang; Hwang, Ha Shin; Kim, Jong Oh; Lee, Eun Seong; Oh, Kyung Taek; Shin, Beom Soo; Choi, Han-Gon; Youn, Yu Seok

2016-08-01

Albumin has gained considerable interest as a material for fabricating nanoparticulate systems due to its biomedical advantages, such as biocompatibility and chemical functionality. Here, we report a new pH-sensitive albumin nanocomplex prototype with a zinc-imidazole coordination bond. Albumin was conjugated with 1-(3-aminopropyl)imidazole and mPEG10kDa-NHS, and the resulting albumin conjugate (PBI) was then modified with either Cy5.5 or BHQ-3. The newly formed albumin nanocomplex (C/BQ-PBI Zn NCs: ∼116nm) system was facilely self-assembled around pH 7.4 in the presence of Zn(2+), but it quickly disassembled in an acidic environment (∼pH 5.0). Based on this pH-sensitivity, C/BQ-PBI Zn NCs emitted strong near-infrared fluorescence and released Zn(2+), turning "off" at pH ∼7.4 (e.g., plasma) and "on" at pH ∼5.0 (e.g., endo/lysosomes in tumor cells) on account of fluorescence resonance energy transfer. C/BQ-PBI Zn NCs displayed significant cytotoxicity due to an increase in cellular Zn(2+) in response to endosomal pH (∼5.0) in breast cancer MCF-7 cells and lung adenocarcinoma A549 cells. Particularly, confocal laser scanning microscopic images showed a strong fluorescence signal caused by the disassembly of C/BQ-PBI Zn NCs in the endosomal region of MCF-7 cells. Based on these results, we believe that this albumin nanocomplex is an attractive biocompatible tumor targeting probe carrier for the theranostic purpose. Copyright © 2016 Elsevier B.V. All rights reserved.

Feasibility study of a lead(II) iodide-based dosimeter for quality assurance in therapeutic radiology

NASA Astrophysics Data System (ADS)

Heo, Y. J.; Kim, K. T.; Oh, K. M.; Lee, Y. K.; Ahn, K. J.; Cho, H. L.; Kim, J. Y.; Min, B. I.; Mun, C. W.; Park, S. K.

2017-09-01

The most widely used form of radiotherapy to treat tumors uses a linear accelerator, and the apparatus requires regular quality assurance (QA). QA for a linear accelerator demands accuracy throughout, from mock treatment and treatment planning, up to treatment itself. Therefore, verifying a radiation dose is essential to ensure that the radiation is being applied as planned. In current clinical practice, ionization chambers and diodes are used for QA. However, using conventional gaseous ionization chambers presents drawbacks such as complex analytical procedures, difficult measurement procedures, and slow response time. In this study, we discuss the potential of a lead(II) iodide (PbI2)-based radiation dosimeter for radiotherapy QA. PbI2 is a semiconductor material suited to measurements of X-rays and gamma rays, because of its excellent response properties to radiation signals. Our results show that the PbI2-based dosimeter offers outstanding linearity and reproducibility, as well as dose-independent characteristics. In addition, percentage depth dose (PDD) measurements indicate that the error at a fixed reference depth Dmax was 0.3%, very similar to the measurement results obtained using ionization chambers. Based on these results, we confirm that the PbI2-based dosimeter has all the properties required for radiotherapy: stable dose detection, dose linearity, and rapid response time. Based on the evidence of this experimental verification, we believe that the PbI2-based dosimeter could be used commercially in various fields for precise measurements of radiation doses in the human body and for measuring the dose required for stereotactic radiosurgery or localized radiosurgery.

Polarized Infrared Absorption of Dipole Centers in Cadmium Halide and PbI2 Crystals

NASA Astrophysics Data System (ADS)

Terakami, Mitsushi; Nakagawa, Hideyuki

2004-03-01

Polarized infrared (IR) absorption measurements on CN- or OH- centers in cadmium halide and PbI2 crystals were carried out at 6 K with a high spectral resolution of 0.025 cm-1 at 2000 cm-1 by using a FTIR spectrometer. Several sharp absorption lines with widths less than 0.1 cm-1 are observed in the energy region of the stretching vibration, i.e. 2000 to 2250 cm-1 for CN- and 2500 to 4500 cm-1 for OH-. These lines are classified into several groups attributed to (1) an isolated center simply substituted for a halogen ion, (2) an interstitial center located between the cadmium and halogen ion sheets and (3) a coupled center with an anion vacancy or a host metal ion. Almost all of the dipole axes (bond axes) of the CN- ions doped in MI2 (M = Cd or Pb) are parallel to the crystal c-axes, while those of the isolated and coupled CN- centers in CdX2 (X = Cl or Br) lean away from the direction of the c-axis. The most OH- ions doped in CdX2 (X = Cl, Br or I) and PbI2 are arranged in the halogen-ion planes with their dipole axes parallel to the crystal c-axes. The first overtone yields values of χe and ωeχe for CN- and OH- in CdX2 and PbI2. These values explain well the isotope shift of the main stretching band in CdX2 and PbI2.

DFT analysis and FDTD simulation of CH3NH3PbI3-x Cl x mixed halide perovskite solar cells: role of halide mixing and light trapping technique

NASA Astrophysics Data System (ADS)

Saffari, Mohaddeseh; Mohebpour, Mohammad Ali; Rahimpour Soleimani, H.; Bagheri Tagani, Meysam

2017-10-01

Since perovskite solar cells have attracted a great deal of attention over the past few years, the enhancement of their optical absorption and current density are among the basic upcoming challenges. For this reason, first, we have studied the structural and optical properties of organic-inorganic hybrid halide perovskite CH3NH3PbI3 and the compounds doped by chlorine halogen CH3NH3PbI3-x Cl x in the cubic phase by using a density functional theory (DFT). Then, we model a single-junction perovskite solar cell based on a full solution to Maxwell’s equations, using a finite difference time domain (FDTD) technique, which helps us to investigate the light absorption efficiency and optical current density of the cell with CH3NH3PbI3-x Cl x (x  =  0, 1, 2, 3) as the active layer. The results suggest that increasing the amount of chlorine in CH3NH3PbI3-x Cl x compound leads to an increase in the bandgap energy, as well as a decrease in the lattice constants and optical properties, like the refractive index and extinction coefficient of the structure. Also, the results obtained by the simulation express that by taking advantage of the light trapping techniques of SiO2, a remarkable increase of light absorption will be achieved to the magnitude of 83.13%, which is noticeable.

Abnormal eating attitudes and behaviours and perceived parental control: a study of white British and British-Asian school girls.

PubMed

Furnham, A; Adam-Saib, S

2001-09-01

Previous studies have found significantly higher scores on the Eating Attitudes Test (EAT-26) which measures eating disorders among second-generation British-Asian schoolgirls in comparison to their White counterparts. Further, high EAT-26 scores (an indication of unhealthy eating attitudes and behaviours) are positively associated with parental overprotection scores on the Parental Bonding Instrument (PBI). This study aimed to replicate and extend previous findings, comparing British-Asian schoolgirls to White schoolgirls and consider 'intra-Asian' differences on the same measures, including factor scores. Participants completed three questionnaires: EAT-26, PBI and BSS (Body Satisfaction Scale). There were 168 participants: 46 White, 40 Indian, 44 Pakistani and 38 Bengali. Previous findings were supported; the Asian scores were significantly higher than the White scores on the EAT-26 and PBI, but not the BSS. The Bengali sample had significantly higher EAT-26 total and 'oral control' scores than the other groups. There were no intra-Asian differences for the overprotection scores. PBI scores were not associated with EAT-26 scores. The BSS score was the only significant predictor of EAT scores, when entered into a regression along with PBI scores and the body mass index. Results demonstrated sociocultural factors in the development of eating disorders. The results suggest that there are important psychological differences between second-generation migrants from different countries on the Indian subcontinent. In line with previous studies, significant differences were found between the four ethnic groups, parenting styles, but these did not relate to actual eating disorders.

Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%.

PubMed

Kim, Hui-Seon; Lee, Chang-Ryul; Im, Jeong-Hyeok; Lee, Ki-Beom; Moehl, Thomas; Marchioro, Arianna; Moon, Soo-Jin; Humphry-Baker, Robin; Yum, Jun-Ho; Moser, Jacques E; Grätzel, Michael; Park, Nam-Gyu

2012-01-01

We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH(3)NH(3))PbI(3) as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI(2) and deposited onto a submicron-thick mesoscopic TiO(2) film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (J(SC)) exceeding 17 mA/cm(2), an open circuit photovoltage (V(OC)) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH(3)NH(3))PbI(3) NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO(2) film. The use of a solid hole conductor dramatically improved the device stability compared to (CH(3)NH(3))PbI(3) -sensitized liquid junction cells.

Polybenzimidazole/Mxene composite membranes for intermediate temperature polymer electrolyte membrane fuel cells.

PubMed

Fei, Mingming; Lin, Ruizhi; Deng, Yuming; Xian, Hongxi; Bian, Renji; Zhang, Xiaole; Cheng, Jigui; Xu, Chenxi; Cai, Dongyu

2018-01-19

This report demonstrated the first study on the use of a new 2D nanomaterial (Mxene) for enhancing membrane performance of intermediate temperature (>100 °C) polymer electrolyte membrane fuel cells (ITPEMFCs). In this study, a typical Ti 3 C 2 T x -MXene was synthesized and incorporated into polybenzimidazole (PBI)-based membranes by using a solution blending method. The composite membrane with 3 wt% Ti 3 C 2 T x -MXene showed the proton conductivity more than 2 times higher than that of pristine PBI membrane at the temperature range of 100 °C-170 °C, and led to substantial increase in maximum power density of fuel cells by ∼30% tested at 150 °C. The addition of Ti 3 C 2 T x -MXene also improved the mechanical properties and thermal stability of PBI membranes. At 3 wt% Ti 3 C 2 T x -MXene, the elongation at break of phosphoric acid doped PBI remained unaffected at 150 °C, and the tensile strength and Young's modulus was increased by ∼150% and ∼160%, respectively. This study pointed out promising application of MXene in ITPEMFCs.

Enhancing the Performance of Perovskite Solar Cells by Hybridizing SnS Quantum Dots with CH3 NH3 PbI3.

PubMed

Han, Jianhua; Yin, Xuewen; Nan, Hui; Zhou, Yu; Yao, Zhibo; Li, Jianbao; Oron, Dan; Lin, Hong

2017-08-01

The combination of perovskite solar cells and quantum dot solar cells has significant potential due to the complementary nature of the two constituent materials. In this study, solar cells (SCs) with a hybrid CH 3 NH 3 PbI 3 /SnS quantum dots (QDs) absorber layer are fabricated by a facile and universal in situ crystallization method, enabling easy embedding of the QDs in perovskite layer. Compared with SCs based on CH 3 NH 3 PbI 3 , SCs using CH 3 NH 3 PbI 3 /SnS QDs hybrid films as absorber achieves a 25% enhancement in efficiency, giving rise to an efficiency of 16.8%. The performance improvement can be attributed to the improved crystallinity of the absorber, enhanced photo-induced carriers' separation and transport within the absorber layer, and improved incident light utilization. The generality of the methods used in this work paves a universal pathway for preparing other perovskite/QDs hybrid materials and the synthesis of entire nontoxic perovskite/QDs hybrid structure. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Lead Iodide Perovskite Sensitized All-Solid-State Submicron Thin Film Mesoscopic Solar Cell with Efficiency Exceeding 9%

PubMed Central

Kim, Hui-Seon; Lee, Chang-Ryul; Im, Jeong-Hyeok; Lee, Ki-Beom; Moehl, Thomas; Marchioro, Arianna; Moon, Soo-Jin; Humphry-Baker, Robin; Yum, Jun-Ho; Moser, Jacques E.; Grätzel, Michael; Park, Nam-Gyu

2012-01-01

We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH3NH3)PbI3 as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI2 and deposited onto a submicron-thick mesoscopic TiO2 film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (JSC) exceeding 17 mA/cm2, an open circuit photovoltage (VOC) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH3NH3)PbI3 NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO2 film. The use of a solid hole conductor dramatically improved the device stability compared to (CH3NH3)PbI3 -sensitized liquid junction cells. PMID:22912919

Electron–acoustic phonon coupling in single crystal CH 3NH 3PbI 3 perovskites revealed by coherent acoustic phonons

DOE PAGES

Mante, Pierre-Adrien; Stoumpos, Constantinos C.; Kanatzidis, Mercouri G.; ...

2017-02-08

The intrinsic properties of CH 3NH 3PbI 3 are still largely unknown in spite of the great amount of attention it has received for its solar cell application. Mobility of charges is a quintessential property in this aspect; however, there is still no clear understanding of electron transport, as reported values span over three orders of magnitude. Here we develop a method to measure the electron and hole deformation potentials using coherent acoustic phonons generated by femtosecond laser pulses. Furthermore, we apply this method to characterize a CH 3NH 3PbI 3 single crystal.We measure the acoustic phonon properties and characterizemore » electron-acoustic phonon scattering. Then, using the deformation potential theory, we calculate the carrier intrinsic mobility and compare it to the reported experimental and theoretical values. These results reveal high electron and hole mobilities of 2,800 and 9,400 cm 2V -1 s -1 , respectively. Comparison with literature values of mobility demonstrates the potential role played by polarons in charge transport in CH 3NH 3PbI 3.« less

Two-dimensional inorganic-organic perovskite hexagonal nanosheets: growth and mechanism

NASA Astrophysics Data System (ADS)

Shakya, Suman; Prakash, G. Vijaya

2015-03-01

In this era of novel technological materials, inorganic-organic (IO) materials has emerged as new class of materials for their application in photonic materials, miniaturized sensors, optoelectronic devices, non-linear optical apparatus by exploiting the properties of both constituents in a single entity. Here we present the formation and growth mechanism of two dimensional Inorganic-organic (IO) perovskite structures from anisotropically grown PbO hexagonal nanosheets, in three steps: Fabrication of hexagonal PbO nanosheets by the versatile bottom-up electrochemical deposition technique, iodinization of PbO into PbI2, followed by conversion of PbI2 into IO hybrid by the intercalation of organic moiety. A systematic and detailed structural study reveals that PbO nanosheet formation is more likely to result from an oriented attachment mechanism, in which the sheets formed by the reduction in surface area that happens during aggregation of small nanoparticle that each has a net dipole moment, which tends to form a self-assembled structure. Intercalation of organic moiety into the PbI2 layers yielded a selfassembled quantum-wells system of one of the IO hybrid, i.e. (C6H9C2H4NH3)2PbI4 (CHPI), sustaining the hexagonal shape.

Self-sorted photoconductive xerogels† †Electronic supplementary information (ESI) available: Full experimental details, rheological data, pK a titrations, further NMR data, full details of the photoconductivity set-up, further photoconductivity measurements. See DOI: 10.1039/c6sc02644c Click here for additional data file.

PubMed Central

Draper, Emily R.; Lee, Jonathan R.; Wallace, Matthew; Jäckel, Frank; Cowan, Alexander J.

2016-01-01

We show that a perylene bisimide (PBI)-based gelator forms self-sorted mixtures with a stilbene-based gelator. To form the self-sorted gels, we use a slow pH change induced by the hydrolysis of glucono-δ-lactone (GdL) to gluconic acid. We prove that self-sorting occurs using NMR spectroscopy, UV-Vis spectroscopy, rheology, and viscometry. The corresponding xerogels are photoconductive. Importantly, the wavelength dependence of the photoconductive films is different to that of the films formed from the perylene bisimide alone. Transient absorption spectroscopy of the xerogels reveals changes in the spectrum of the PBI on the picosecond timescale in the presence of stilbene with a PBI radical anion being formed within 10 ps when the stilbene is present. The ability to form the PBI radical anion under visible light leads to the enhanced spectral response of the multicomponent gels. These systems therefore have potential as useful visible-active optoelectronics. PMID:28451108

Electron–acoustic phonon coupling in single crystal CH 3NH 3PbI 3 perovskites revealed by coherent acoustic phonons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mante, Pierre-Adrien; Stoumpos, Constantinos C.; Kanatzidis, Mercouri G.

The intrinsic properties of CH 3NH 3PbI 3 are still largely unknown in spite of the great amount of attention it has received for its solar cell application. Mobility of charges is a quintessential property in this aspect; however, there is still no clear understanding of electron transport, as reported values span over three orders of magnitude. Here we develop a method to measure the electron and hole deformation potentials using coherent acoustic phonons generated by femtosecond laser pulses. Furthermore, we apply this method to characterize a CH 3NH 3PbI 3 single crystal.We measure the acoustic phonon properties and characterizemore » electron-acoustic phonon scattering. Then, using the deformation potential theory, we calculate the carrier intrinsic mobility and compare it to the reported experimental and theoretical values. These results reveal high electron and hole mobilities of 2,800 and 9,400 cm 2V -1 s -1 , respectively. Comparison with literature values of mobility demonstrates the potential role played by polarons in charge transport in CH 3NH 3PbI 3.« less

Polybenzimidazole/Mxene composite membranes for intermediate temperature polymer electrolyte membrane fuel cells

NASA Astrophysics Data System (ADS)

Fei, Mingming; Lin, Ruizhi; Deng, Yuming; Xian, Hongxi; Bian, Renji; Zhang, Xiaole; Cheng, Jigui; Xu, Chenxi; Cai, Dongyu

2018-01-01

This report demonstrated the first study on the use of a new 2D nanomaterial (Mxene) for enhancing membrane performance of intermediate temperature (>100 °C) polymer electrolyte membrane fuel cells (ITPEMFCs). In this study, a typical Ti3C2T x -MXene was synthesized and incorporated into polybenzimidazole (PBI)-based membranes by using a solution blending method. The composite membrane with 3 wt% Ti3C2T x -MXene showed the proton conductivity more than 2 times higher than that of pristine PBI membrane at the temperature range of 100 °C-170 °C, and led to substantial increase in maximum power density of fuel cells by ˜30% tested at 150 °C. The addition of Ti3C2T x -MXene also improved the mechanical properties and thermal stability of PBI membranes. At 3 wt% Ti3C2T x -MXene, the elongation at break of phosphoric acid doped PBI remained unaffected at 150 °C, and the tensile strength and Young’s modulus was increased by ˜150% and ˜160%, respectively. This study pointed out promising application of MXene in ITPEMFCs.

Efficient luminescent solar cells based on tailored mixed-cation perovskites

PubMed Central

Bi, Dongqin; Tress, Wolfgang; Dar, M. Ibrahim; Gao, Peng; Luo, Jingshan; Renevier, Clémentine; Schenk, Kurt; Abate, Antonio; Giordano, Fabrizio; Correa Baena, Juan-Pablo; Decoppet, Jean-David; Zakeeruddin, Shaik Mohammed; Nazeeruddin, Mohammad Khaja; Grätzel, Michael; Hagfeldt, Anders

2016-01-01

We report on a new metal halide perovskite photovoltaic cell that exhibits both very high solar-to-electric power-conversion efficiency and intense electroluminescence. We produce the perovskite films in a single step from a solution containing a mixture of FAI, PbI2, MABr, and PbBr2 (where FA stands for formamidinium cations and MA stands for methylammonium cations). Using mesoporous TiO2 and Spiro-OMeTAD as electron- and hole-specific contacts, respectively, we fabricate perovskite solar cells that achieve a maximum power-conversion efficiency of 20.8% for a PbI2/FAI molar ratio of 1.05 in the precursor solution. Rietveld analysis of x-ray diffraction data reveals that the excess PbI2 content incorporated into such a film is about 3 weight percent. Time-resolved photoluminescence decay measurements show that the small excess of PbI2 suppresses nonradiative charge carrier recombination. This in turn augments the external electroluminescence quantum efficiency to values of about 0.5%, a record for perovskite photovoltaics approaching that of the best silicon solar cells. Correspondingly, the open-circuit photovoltage reaches 1.18 V under AM 1.5 sunlight. PMID:26767196

Highly durable polymer electrolyte membranes at elevated temperature: Cross-linked copolymer structure consisting of poly(benzoxazine) and poly(benzimidazole)

NASA Astrophysics Data System (ADS)

Kim, Sung-Kon; Kim, Ki-Hyun; Park, Jung Ock; Kim, Kihyun; Ko, Taeyun; Choi, Seong-Woo; Pak, Chanho; Chang, Hyuk; Lee, Jong-Chan

2013-03-01

For polymer electrolyte membrane fuel cell (PEMFC) applications at elevated temperature (>100 °C), a series of cross-linked benzoxazine-benzimidazole copolymer, P(HFa-co-BI), membranes are prepared by casting a solution of poly[2,2‧-(m-phenylene)-5,5‧-bibenzimidazole] (PBI) and di-functional benzoxazine monomer, 6,6‧-(hexafluoroisopropylidene)bis(3-phenyl-3,4-dihydro-2H-benzoxazine) (HFa), in N,N-dimethylacetamide prior to stepwise heating to 250 °C. The films are also viable to manufacture to large quantities and area by roll-to-roll coating. The resulting cross-linked copolymer, P(HFa-co-BI), membranes are found to be thermally and mechanically stable. Although the proton conductivity values of P(HFa-co-BI) membranes are smaller than that of the PBI membrane, their cell performance (0.68 V at 0.2 A cm-2 at 150 °C) is close to that of PBI membrane and their long-term durability (ca. 3116 cycles on in situ accelerated lifetime mode of load cycling testing) is found to be far superior to the PBI membrane.

Optimization of the Pressurized Logistics Module - A Space Station Freedom analytical study

NASA Technical Reports Server (NTRS)

Scallan, J. M.

1991-01-01

The analysis for determining the optimum cylindrical length of the Space Station Freedom (SSF) Pressurized Logistics Module, whose task is to transport the SSF pressurized cargo via the NSTS Shuttle Orbiter, is described. The major factors considered include the NSTS net launch lift capability, the pressurized cargo requirements, and the mass properties of the module structures, mechanisms, and subsystems.

KSC-07pd0630

NASA Image and Video Library

2007-03-13

KENNEDY SPACE CENTER, FLA. -- At the Trident wharf, the shipping container with the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module is ready for lifting out of the hold of the ship that brought it from Yokohama, Japan. The logistics module will be offloaded and transported to the Space Station Processing Facility at NASA's Kennedy Space Center. The Japanese Experiment Module is composed of three segments and is known as Kibo, which means "hope" in Japanese. Kibo consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. Kibo is Japan's first human space facility and its primary contribution to the station. Kibo will enhance the unique research capabilities of the orbiting complex by providing an additional environment in which astronauts can conduct science experiments. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the Space Shuttle Endeavour, targeted for launch in 2007. Photo credit: NASA/Kim Shiflett

6.5% efficient perovskite quantum-dot-sensitized solar cell.

PubMed

Im, Jeong-Hyeok; Lee, Chang-Ryul; Lee, Jin-Wook; Park, Sang-Won; Park, Nam-Gyu

2011-10-05

Highly efficient quantum-dot-sensitized solar cell is fabricated using ca. 2-3 nm sized perovskite (CH(3)NH(3))PbI(3) nanocrystal. Spin-coating of the equimolar mixture of CH(3)NH(3)I and PbI(2) in γ-butyrolactone solution (perovskite precursor solution) leads to (CH(3)NH(3))PbI(3) quantum dots (QDs) on nanocrystalline TiO(2) surface. By electrochemical junction with iodide/iodine based redox electrolyte, perovskite QD-sensitized 3.6 μm-thick TiO(2) film shows maximum external quantum efficiency (EQE) of 78.6% at 530 nm and solar-to-electrical conversion efficiency of 6.54% at AM 1.5G 1 sun intensity (100 mW cm(-2)), which is by far the highest efficiency among the reported inorganic quantum dot sensitizers.

Parental rearing style: examining for links with personality vulnerability factors for depression.

PubMed

Parker, G

1993-07-01

Recent research provides evidence of links between anomalous parenting experiences in childhood and subsequent depression. A study was designed to pursue the possibility that anomalous parenting effects a diathesis to depression by inducing a vulnerable cognitive style rather than by disposing directly to depression. Possible mediating personality style variables were explored in a study of 123 depressed subjects who scored their parents on the Parental Bonding Instrument (PBI), as well as completing a state depression and several relevant personality measures. Low self-esteem and a related dysfunction cognitive style were the personality variables most clearly linked with PBI scores, with links persisting after partialling out state levels of depression. Failure to find links between PBI scores and depression levels limited explication of the diathesis stress model.

The recollection of parental rearing styles in patients with panic disorder.

PubMed

Wiborg, I M; Dahl, A A

1997-07-01

Studies of the mental image of parents assessed by means of the Parental Bonding Instrument (PBI) in patients with panic disorder (according to DSM-III-R) have shown conflicting results. We examined 45 patients with panic disorder with and without agoraphobia and 116 controls using the PBI. As a group, patients with panic disorder reported significantly less care and more protection from parents than the controls. This difference was shown by the patients who had panic disorder with major agoraphobia, while those with minor agoraphobia did not differ from the controls. The present study supports the findings that low levels of care and high levels of protection, rather than affectionate constraint, were the predominant mental image reported by patients with panic disorder, using the PBI.

KSC-07pd0898

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, Scott Higginbotham, payload manager for the International Space Station, stands in front of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module. The module will be delivered to the space station on mission STS-123. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the logistics module. The module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

Organometal Halide Perovskite Solar Absorbers and Ferroelectric Nanocomposites for Harvesting Solar Energy

NASA Astrophysics Data System (ADS)

Hettiarachchi, Chaminda Lakmal

Organometal halide perovskite absorbers such as methylammonium lead iodide chloride (CH3NH3PbI3-xClx), have emerged as an exciting new material family for photovoltaics due to its appealing features that include suitable direct bandgap with intense light absorbance, band gap tunability, ultra-fast charge carrier generation, slow electron-hole recombination rates, long electron and hole diffusion lengths, microsecond-long balanced carrier mobilities, and ambipolarity. The standard method of preparing CH3NH3PbI3-xClx perovskite precursors is a tedious process involving multiple synthesis steps and, the chemicals being used (hydroiodic acid and methylamine) are quite expensive. This work describes a novel, single-step, simple, and cost-effective solution approach to prepare CH3NH3PbI3-xClx thin films by the direct reaction of the commercially available CH3NH 3Cl (or MACl) and PbI2. A detailed analysis of the structural and optical properties of CH3NH3PbI3-xCl x thin films deposited by aerosol assisted chemical vapor deposition is presented. Optimum growth conditions have been identified. It is shown that the deposited thin films are highly crystalline with intense optical absorbance. Charge carrier separation of these thin films can be enhanced by establishing a local internal electric field that can reduce electron-hole recombination resulting in increased photo current. The intrinsic ferroelectricity in nanoparticles of Barium Titanate (BaTiO3 -BTO) embedded in the solar absorber can generate such an internal field. A hybrid structure of CH3NH 3PbI3-xClx perovskite and ferroelectric BTO nanocomposite FTO/TiO2/CH3NH3PbI3-xClx : BTO/P3HT/Cu as a new type of photovoltaic device is investigated. Aerosol assisted chemical vapor deposition process that is scalable to large-scale manufacturing was used for the growth of the multilayer structure. TiO 2 and P3HT with additives were used as ETL and HTL respectively. The growth process of the solar absorber layer includes the nebulization of a mixture of PbI2 and CH3NH3Cl perovskite precursors and BTO nanoparticles dissolved in DMF, and injection of the aerosol into the growth chamber and subsequent deposition on TiO2. While high percentage of BTO in the film increases the carrier separation, it also leads to reduced carrier generation. A model was developed to guide the optimum BTO nanoparticle concentration in the nanocomposite films. Characterization of perovskite solar cells indicated that ferroelectric polarization of BTO nanoparticles leads to the increase of the width of depletion regions in the perovskite layer hence the photo current was increased by one order of magnitude after poling the devices. The ferroelectric polarization of BTO nanoparticles within the perovskite solar absorber provides a new perspective for tailoring the working mechanism and photovoltaic performance of perovskite solar cells.

Lewis Acid-Base Adduct Approach for High Efficiency Perovskite Solar Cells.

PubMed

Lee, Jin-Wook; Kim, Hui-Seon; Park, Nam-Gyu

2016-02-16

Since the first report on the long-term durable 9.7% solid-state perovskite solar cell employing methylammonium lead iodide (CH3NH3PbI3), mesoporous TiO2, and 2,2',7,7'-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9'-spirobifluorene (spiro-MeOTAD) in 2012, following the seed technologies on perovskite-sensitized liquid junction solar cells in 2009 and 2011, a surge of interest has been focused on perovskite solar cells due to superb photovoltaic performance and extremely facile fabrication processes. The power conversion efficiency (PCE) of perovskite solar cells reached 21% in a very short period of time. Such an unprecedentedly high photovoltaic performance is due to the intrinsic optoelectronic property of organolead iodide perovskite material. Moreover, a high dielectric constant, sub-millimeter scale carrier diffusion length, an underlying ferroelectric property, and ion migration behavior can make organolead halide perovskites suitable for multifunctionality. Thus, besides solar cell applications, perovskite material has recently been applied to a variety fields of materials science such as photodetectors, light emitting diodes, lasing, X-ray imaging, resistive memory, and water splitting. Regardless of application areas, the growth of a well-defined perovskite layer with high crystallinity is essential for effective utilization of its excellent physicochemical properties. Therefore, an effective methodology for preparation of high quality perovskite layers is required. In this Account, an effective methodology for production of high quality perovskite layers is described, which is the Lewis acid-base adduct approach. In the solution process to form the perovskite layer, the key chemicals of CH3NH3I (or HC(NH2)2I) and PbI2 are used by dissolving them in polar aprotic solvents. Since polar aprotic solvents bear oxygen, sulfur, or nitrogen, they can act as a Lewis base. In addition, the main group compound PbI2 is known to be a Lewis acid. Thus, PbI2 has a chance to form an adduct by reacting with the Lewis base. Crystal growth and morphology of perovskite can be controlled by taking advantage of the weak chemical interaction in the adduct. We have successfully fabricated highly reproducible CH3NH3PbI3 perovskite solar cells with PCE as high as 19.7% via adducts of PbI2 with oxygen-donor N,N'-dimethyl sulfoxide. This adduct approach has been found to be generally adopted, where formamidinium lead iodide perovskite, HC(NH2)2PbI3 (FAPbI3), with large grain, high crystallinity, and long-lived carrier lifetime was successfully fabricated via an adduct of PbI2 with sulfur-donor thiourea as Lewis base. The adduct approach proposed in this Account is a very promising methodology to achieve high quality perovskite films with high photovoltaic performance. Furthermore, single crystal growth on the conductive substrate is expected to be possible if we kinetically control the elimination of Lewis base in the adduct.

Logistics Enterprise Evaluation Model Based On Fuzzy Clustering Analysis

NASA Astrophysics Data System (ADS)

Fu, Pei-hua; Yin, Hong-bo

In this thesis, we introduced an evaluation model based on fuzzy cluster algorithm of logistics enterprises. First of all,we present the evaluation index system which contains basic information, management level, technical strength, transport capacity,informatization level, market competition and customer service. We decided the index weight according to the grades, and evaluated integrate ability of the logistics enterprises using fuzzy cluster analysis method. In this thesis, we introduced the system evaluation module and cluster analysis module in detail and described how we achieved these two modules. At last, we gave the result of the system.

KSC-07pd0902

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- The Experiment Logistics Module Pressurized Section of the Japanese Experiment Module sits on top of a stand in the Space Station Processing Facility. Earlier, NASA and Japanese Space Agency (JAXA) officials welcomed the arrival of the logistics module, which will be delivered to the space station on mission STS-123. The module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

KSC-07pd0901

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- After a welcoming ceremony for the Experiment Logistics Module Pressurized Section of the Japanese Experiment Module, STS-123 Commander Dominic Gorie talks to the media. Earlier, NASA and Japanese Space Agency (JAXA) officials welcomed the arrival of the logistics module, which will be delivered to the space station on mission STS-123. The module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

KSC-07pd0899

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, Scott Higginbotham and Chuong Nguyen, payload manager and deputy payload manager respectively for the International Space Station, stand in front of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the logistics module. The module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

Programmable Thermostat Module Upgrade for the Multipurpose Logistics Module

NASA Technical Reports Server (NTRS)

Clark, D. W.; Glasgow, S. d.; Reagan, S. E.; Presson, K. H.; Howard, D. E.; Smith, D. A.

2007-01-01

The STS-121/ULF 1.1 mission was the maiden flight of the programmable thermostat module (PTM) system used to control the 28 V shell heaters on the multi-purpose logistics module (MPLM). These PTMs, in conjunction with a data recorder module (DRM), provide continuous closed loop temperature control and data recording of MPLM on-orbit heater operations. This Technical Memorandum discusses the hardware design, development, test, and verification (DDT&V) activities performed at the Marshall Space Flight Center as well as the operational implementation and mission performance.

Programmable Thermostat Module Upgrade for the Multi-Purpose Logistics Module

NASA Technical Reports Server (NTRS)

Clark, Dallas; Glasgow, Shaun; Reagan, Shawn; Presson, Keith; Howard, David; Smith, Dennis

2007-01-01

The STS-121/ULF1.1 mission was the maiden flight of the Programmable Thermostat Module (PTM) system used to control the 28 V shell heaters on the Multi-Purpose Logistics Module (MPLM). These PTMs, in conjunction with a Data Recorder Module (DRM), provide continuous closed loop temperature control and data recording of MPLM on-orbit heater operations. This paper will discuss the hardware design, development, test and verification (DDT&V) activities performed at the Marshall Space Flight Center (MSFC) as well as the operational implementation and mission performance.

Preoperative Single-Fraction Partial Breast Radiation Therapy: A Novel Phase 1, Dose-Escalation Protocol With Radiation Response Biomarkers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horton, Janet K., E-mail: janet.horton@duke.edu; Blitzblau, Rachel C.; Yoo, Sua

Purpose: Women with biologically favorable early-stage breast cancer are increasingly treated with accelerated partial breast radiation (PBI). However, treatment-related morbidities have been linked to the large postoperative treatment volumes required for external beam PBI. Relative to external beam delivery, alternative PBI techniques require equipment that is not universally available. To address these issues, we designed a phase 1 trial utilizing widely available technology to 1) evaluate the safety of a single radiation treatment delivered preoperatively to the small-volume, intact breast tumor and 2) identify imaging and genomic markers of radiation response. Methods and Materials: Women aged ≥55 years with clinically node-negative,more » estrogen receptor–positive, and/or progesterone receptor–positive HER2−, T1 invasive carcinomas, or low- to intermediate-grade in situ disease ≤2 cm were enrolled (n=32). Intensity modulated radiation therapy was used to deliver 15 Gy (n=8), 18 Gy (n=8), or 21 Gy (n=16) to the tumor with a 1.5-cm margin. Lumpectomy was performed within 10 days. Paired pre- and postradiation magnetic resonance images and patient tumor samples were analyzed. Results: No dose-limiting toxicity was observed. At a median follow-up of 23 months, there have been no recurrences. Physician-rated cosmetic outcomes were good/excellent, and chronic toxicities were grade 1 to 2 (fibrosis, hyperpigmentation) in patients receiving preoperative radiation only. Evidence of dose-dependent changes in vascular permeability, cell density, and expression of genes regulating immunity and cell death were seen in response to radiation. Conclusions: Preoperative single-dose radiation therapy to intact breast tumors is well tolerated. Radiation response is marked by early indicators of cell death in this biologically favorable patient cohort. This study represents a first step toward a novel partial breast radiation approach. Preoperative radiation should be tested in future clinical trials because it has the potential to challenge the current treatment paradigm and provide a path forward to identify radiation response biomarkers.« less

Fireblocking Fibers

NASA Technical Reports Server (NTRS)

1986-01-01

PBI was originally developed for space suits. In 1980, the need for an alternative to asbestos and stricter government anti-pollution standards led to commercialization of the fire blocking fiber. PBI is used for auto racing driver suits and aircraft seat covers. The fiber does not burn in air, is durable and easily maintained. It has been specified by a number of airliners and is manufactured by Hoechst-Celanese Corporation.

Comparing the Effectiveness of Processing Instruction and Production-Based Instruction on L2 Grammar Learning: The Role of Explicit Information

ERIC Educational Resources Information Center

Soruç, Adem; Qin, Jingjing; Kim, YouJin

2017-01-01

This article reports on a study that investigated whether processing instruction(PI) or production-based instruction (PBI) is more effective for the teaching of regular past simple verb forms in English. In addition, this study examined whether explicit grammatical information (EI) mediates the effectiveness of PI or PBI. A total of 194 Turkish…

Preclinical Biodistribution and Safety Evaluation of a pbi-shRNA STMN1 Lipoplex after Subcutaneous Delivery.

PubMed

Wang, Zhaohui; Jay, Christopher M; Evans, Courtney; Kumar, Padmasini; Phalon, Connor; Rao, Donald D; Senzer, Neil; Nemunaitis, John

2017-02-01

Stathmin-1 (STMN1) is a microtubule-destabilizing protein which is overexpressed in cancer. Its overexpression is associated with poor prognosis and also serves as a predictive marker to taxane therapy. We have developed a proprietary bi-functional shRNA (bi-shRNA) platform to execute RNA interference (RNAi)-mediated gene silencing and a liposome-carrier complex to systemically deliver the pbi-shRNA plasmids. In vitro and in vivo testing demonstrated efficacy and specificity of pbi-shRNA plasmid in targeting STMN1 (Phadke, A. P., Jay, C. M., Wang, Z., Chen, S., Liu, S., Haddock, C., Kumar, P., Pappen, B. O., Rao, D. D., Templeton, N. S., et al. (2011). In vivo safety and antitumor efficacy of bifunctional small hairpin RNAs specific for the human Stathmin 1 oncoprotein. DNA Cell Biol. 30, 715-726.). Biodistribution and toxicology studies in bio-relevant Sprague Dawley rats with pbi-shRNA STMN1 lipoplex revealed that the plasmid DNA was delivered to a broad distribution of organs after a single subcutaneous injection. Specifically, plasmid was detected within the first week using QPCR (threshold 50 copies plasmid/1 µg genomic DNA) at the injection site, lung, spleen, blood, skin, ovary (limited), lymph nodes, and liver. It was not detected in the heart, testis or bone marrow. No plasmid was detected from any organ 30 days after injection. Treatment was well tolerated. Minimal inflammation/erythema was observed at the injection site. Circulating cytokine response was also examined by ELISA. The IL-6 levels were induced within 6 h then declined to the vehicle control level 72 h after the injection. TNFα induction was transiently observed 4 days after the DNA lipoplex treatment. In summary, the pbi-shRNA STMN1 lipoplex was well tolerated and displayed broad distribution after a single subcutaneous injection. The pre-clinical data has been filed to FDA and the pbi-shRNA STMN1 lipoplex is being investigated in a phase I clinical study. © The Author 2016. Published by Oxford University Press on behalf of the Society of Toxicology. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Reduced Mortality With Partial-Breast Irradiation for Early Breast Cancer: A Meta-Analysis of Randomized Trials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaidya, Jayant S., E-mail: jayant.vaidya@ucl.ac.uk; Department of Surgery, Royal Free Hospital, London; Department of Surgery, Whittington Health, London

Purpose: With earlier detection and more effective treatment, mortality from breast cancer continues to fall and it has become increasingly important to reduce the toxicity of treatments. Partial-breast radiation therapy, which focuses radiation to the tumor bed, may achieve this aim. We analyzed mortality differences in randomized trials of partial-breast irradiation (PBI). Methods and Materials: We included data from published randomized trials of PBI (alone or as part of a risk-adapted approach) versus whole-breast irradiation (WBI) for invasive breast cancer suitable for breast-conserving therapy. We identified trials using PubMed and Google searches with the terms “partial breast irradiation” OR “intraoperativemore » radiotherapy” OR “IMRT” OR (“accelerated” AND “radiation”) AND “randomised/randomized,” as well as through discussion with colleagues in the field. We calculated the proportion of patients who had events in each randomized arm at 5 years' follow-up and created a forest plot using Stata, version 14.1. Results: We identified 9 randomized trials of PBI versus WBI in invasive breast cancer; 5-year outcomes were available for non–breast cancer mortality in 5 trials (n=4489) and for breast cancer mortality in 4 trials (n=4231). The overall mortality was 4.9%. There was no detectable heterogeneity between the trials for any of the outcomes. There was no difference in the proportion of patients dying of breast cancer (difference, 0.000% [95% confidence interval (CI), −0.7 to +0.7]; P=.999). Non–breast cancer mortality with PBI was lower than with WBI (difference, 1.1% [95% CI, −2.1% to −0.2%]; P=.023). Total mortality with PBI was also lower than with WBI (difference, 1.3% [95% CI, −2.5% to 0.0%]; P=.05). Conclusions: Use of PBI instead of WBI in selected patients results in a lower 5-year non–breast cancer and overall mortality, amounting to a 25% reduction in relative terms. This information should be included when breast-conserving therapy is proposed to a patient.« less

Two-Dimensional Lead(II) Halide-Based Hybrid Perovskites Templated by Acene Alkylamines: Crystal Structures, Optical Properties, and Piezoelectricity.

PubMed

Du, Ke-Zhao; Tu, Qing; Zhang, Xu; Han, Qiwei; Liu, Jie; Zauscher, Stefan; Mitzi, David B

2017-08-07

A series of two-dimensional (2D) hybrid organic-inorganic perovskite (HOIP) crystals, based on acene alkylamine cations (i.e., phenylmethylammonium (PMA), 2-phenylethylammonium (PEA), 1-(2-naphthyl)methanammonium (NMA), and 2-(2-naphthyl)ethanammonium (NEA)) and lead(II) halide (i.e., PbX 4 2- , X = Cl, Br, and I) frameworks, and their corresponding thin films were fabricated and examined for structure-property relationship. Several new or redetermined crystal structures are reported, including those for (NEA) 2 PbI 4 , (NEA) 2 PbBr 4 , (NMA) 2 PbBr 4 , (PMA) 2 PbBr 4 , and (PEA) 2 PbI 4 . Non-centrosymmetric structures from among these 2D HOIPs were confirmed by piezoresponse force microscopy-especially noteworthy is the structure of (PMA) 2 PbBr 4 , which was previously reported as centrosymmetric. Examination of the impact of organic cation and inorganic layer choice on the exciton absorption/emission properties, among the set of compounds considered, reveals that perovskite layer distortion (i.e., Pb-I-Pb bond angle between adjacent PbI 6 octahedra) has a more global effect on the exciton properties than octahedral distortion (i.e., variation of I-Pb-I bond angles and discrepancy among Pb-I bond lengths within each PbI 6 octahedron). In addition to the characteristic sharp exciton emission for each perovskite, (PMA) 2 PbCl 4 , (PEA) 2 PbCl 4 , (NMA) 2 PbCl 4 , and (PMA) 2 PbBr 4 exhibit separate, broad "white" emission in the long wavelength range. Piezoelectric compounds identified from these 2D HOIPs may be considered for future piezoresponse-type energy or electronic applications.

Relativistic GW calculations on CH3NH3PbI3 and CH3NH3SnI3 perovskites for solar cell applications.

PubMed

Umari, Paolo; Mosconi, Edoardo; De Angelis, Filippo

2014-03-26

Hybrid AMX3 perovskites (A = Cs, CH3NH3; M = Sn, Pb; X = halide) have revolutionized the scenario of emerging photovoltaic technologies, with very recent results demonstrating 15% efficient solar cells. The CH3NH3PbI3/MAPb(I(1-x)Cl(x))3 perovskites have dominated the field, while the similar CH3NH3SnI3 has not been exploited for photovoltaic applications. Replacement of Pb by Sn would facilitate the large uptake of perovskite-based photovoltaics. Despite the extremely fast progress, the materials electronic properties which are key to the photovoltaic performance are relatively little understood. Density Functional Theory electronic structure methods have so far delivered an unbalanced description of Pb- and Sn-based perovskites. Here we develop an effective GW method incorporating spin-orbit coupling which allows us to accurately model the electronic, optical and transport properties of CH3NH3SnI3 and CH3NH3PbI3, opening the way to new materials design. The different CH3NH3SnI3 and CH3NH3PbI3 electronic properties are discussed in light of their exploitation for solar cells, and found to be dominantly due to relativistic effects. These effects stabilize the CH3NH3PbI3 material towards oxidation, by inducing a deeper valence band edge. Relativistic effects, however, also increase the material band-gap compared to CH3NH3SnI3, due to the valence band energy downshift (~0.7 eV) being only partly compensated by the conduction band downshift (~0.2 eV).

Fluorescent J-aggregates of core-substituted perylene bisimides: studies on structure-property relationship, nucleation-elongation mechanism, and sergeants-and-soldiers principle.

PubMed

Kaiser, Theo E; Stepanenko, Vladimir; Würthner, Frank

2009-05-20

A series of highly soluble and fluorescent, at core tetraaryloxy-substituted and in imide positions hydrogen atom containing perylene bisimide (PBI) dyes 1a-e with varying peripheral side chains have been synthesized and thoroughly characterized. The self-assembly of these PBIs has been studied in detail by UV/vis, linear dichroism (LD) and circular dichroism (CD) spectroscopy, and scanning probe microscopy (AFM, STM). These studies revealed that the present PBIs self-assemble into extended double string cables, which consist of two hydrogen-bonded supramolecular polymeric chains of densely packed and strongly excitonically coupled PBI chromophores, providing highly fluorescent J-aggregates. The aggregation strength ("melting" temperature) and the fluorescence properties of these J-aggregates are dependent on the number and chain length of the peripheral alkoxy substituents, thus revealing a structure-property relationship. In contrast to previously reported assemblies of PBIs, for which the aggregation process is described by the isodesmic (or equal K) model, a cooperative nucleation-elongation mechanism applies for the aggregation of the present assemblies as revealed by concentration-dependent UV/vis absorption studies with the chiral PBI 1e, providing equilibrium constants for dimerization (= nucleation) of K(2) = 13 +/- 11 L mol(-1) and for elongation of K = 2.3 +/- 0.1 x 10(6) L mol(-1) in methylcyclohexane (MCH). LD spectroscopic measurements have been performed to analyze the orientation of the monomers within the aggregates. The nonlinearity of chiral amplification in PBI aggregates directed by sergeants-and-soldiers principle has been elucidated by coaggregation experiments of different PBI dyes using CD spectroscopy. The dimensions as well as the molecular arrangement of the monomeric units in assemblies have been explored by atomic force microscopy (AFM) and scanning tunneling microscopy (STM).

High-efficiency perovskite solar cells prepared by using a sandwich structure MAI-PbI2-MAI precursor film.

PubMed

Zhang, Xuhui; Ye, Jiajiu; Zhu, Liangzheng; Zheng, Haiying; Liu, Guozhen; Liu, Xuepeng; Duan, Bin; Pan, Xu; Dai, Songyuan

2017-04-06

Two-step deposition has been widely used in the perovskite layer preparation for perovskite solar cells due to its attractive morphology controllability. However, the limited diffusivity of CH 3 NH 3 I (MAI) might cause some PbI 2 to remain in the perovskite film. The residual PbI 2 in the perovskite film would lead to inferior performance of devices, such as, low power conversion efficiency (PCE), poor reproducibility and weak air stability. In this work, we developed a sandwich structure MAI-PbI 2 -MAI precursor film to prepare a PbI 2 -free CH 3 NH 3 PbI 3 perovskite film. In comparison to the two-step approach, the MAI-PbI 2 -MAI precursor film with a typical sandwich structure formed a uniform and pinhole-free perovskite film without any PbI 2 residue, which could significantly improve the performance of the devices. Moreover, the bottom MAI layer of the MAI-PbI 2 -MAI precursor film could improve the interfacial contact of the porous TiO 2 layer, leading to the promotion of the charge transfer and reduction of the recombination rate. Therefore, the devices fabricated from the sandwich structure MAI-PbI 2 -MAI precursor films showed dramatic improvements of open-circuit voltage (V oc ), short-circuit current density (J sc ), fill factor (FF) and PCE. As a result, a promising PCE of 17.8% with good long-term air stability was achieved for the MAI-PbI 2 -MAI precursor film based PSC, which is better than that prepared by a two-step approach.

Relativistic GW calculations on CH3NH3PbI3 and CH3NH3SnI3 Perovskites for Solar Cell Applications

PubMed Central

Umari, Paolo; Mosconi, Edoardo; De Angelis, Filippo

2014-01-01

Hybrid AMX3 perovskites (A = Cs, CH3NH3; M = Sn, Pb; X = halide) have revolutionized the scenario of emerging photovoltaic technologies, with very recent results demonstrating 15% efficient solar cells. The CH3NH3PbI3/MAPb(I1−xClx)3 perovskites have dominated the field, while the similar CH3NH3SnI3 has not been exploited for photovoltaic applications. Replacement of Pb by Sn would facilitate the large uptake of perovskite-based photovoltaics. Despite the extremely fast progress, the materials electronic properties which are key to the photovoltaic performance are relatively little understood. Density Functional Theory electronic structure methods have so far delivered an unbalanced description of Pb- and Sn-based perovskites. Here we develop an effective GW method incorporating spin-orbit coupling which allows us to accurately model the electronic, optical and transport properties of CH3NH3SnI3 and CH3NH3PbI3, opening the way to new materials design. The different CH3NH3SnI3 and CH3NH3PbI3 electronic properties are discussed in light of their exploitation for solar cells, and found to be dominantly due to relativistic effects. These effects stabilize the CH3NH3PbI3 material towards oxidation, by inducing a deeper valence band edge. Relativistic effects, however, also increase the material band-gap compared to CH3NH3SnI3, due to the valence band energy downshift (~0.7 eV) being only partly compensated by the conduction band downshift (~0.2 eV). PMID:24667758

Is It Necessary to Achieve a Complete Box Isolation in the Case of Frequent Esophageal Temperature Rises? Feasibility of Shifting to a Partial Box Isolation Strategy for Patients With Non-Paroxysmal Atrial Fibrillation.

PubMed

Higuchi, Satoshi; Sohara, Hiroshi; Nakamura, Yoshinori; Ihara, Minoru; Yamaguchi, Yoshio; Shoda, Morio; Hagiwara, Nobuhisa; Satake, Shutaro

2016-08-01

There are some cases with frequent luminal esophageal temperature (LET) rises despite titrating the radiofrequency energy while creating a linear lesion for the Box isolation of atrial fibrillation (AF). Little is known about the feasibility of redesigning the ablation lines for a modified Box isolation strategy to prevent fatal esophageal injury in those cases. Two hundred and seventeen patients who underwent a Box isolation of non-paroxysmal AF were evaluated. We divided them into 2 groups, patients in whom a box lesion set of the entire posterior left atrium had been achieved (complete Box isolation [CBI]; n = 157) and those in whom 2 additional peri-esophageal vertical lines were created at both the right and left ends of the esophagus, and those areas were left with an incomplete isolation when frequent rapid LET rises above 39.0 °C were observed while creating the floor line (partial Box isolation [PBI]; n = 60). During 20.1 ± 13.9 months of follow-up, the arrhythmia-free rates were 54.1% in the CBI group versus 48.3% in the PBI group (P = 0.62). In the second session, a complete Box isolation was highly achieved even in the PBI group (94.3% vs. 83.3%, respectively; P = 0.17) and after 2 procedures, the arrhythmia-free rates increased to 75.2% vs. 68.3%, respectively (P = 0.34). There was no symptomatic esophageal injury in the PBI group. In the case of frequent LET rises while creating the linear lesions for the Box isolation strategy for non-paroxysmal AF, shifting to the PBI strategy was feasible. © 2016 Wiley Periodicals, Inc.

Technical Note: Partial body irradiation of mice using a customized PMMA apparatus and a clinical 3D planning/LINAC radiotherapy system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karagounis, Ilias V.; Koukourakis, Michael I., E-mail: targ@her.forthnet.gr, E-mail: mkoukour@med.duth.gr; Abatzoglou, Ioannis M., E-mail: abadzoglou@yahoo.gr

Purpose: In vivo radiobiology experiments involving partial body irradiation (PBI) of mice are of major importance because they allow for the evaluation of individual organ tolerance; overcoming current limitations of experiments using lower dose, whole body irradiation. In the current study, the authors characterize and validate an effective and efficient apparatus for multiple animal PBI, directed to the head, thorax, or abdomen of mice. Methods: The apparatus is made of polymethylmethacrylate and consists of a rectangular parallelepiped prism (40 cm × 16 cm × 8 cm), in which five holes were drilled to accomodate standard 60 ml syringes, each housingmore » an unanesthetized, fully immobilized mouse. Following CT-scanning and radiotherapy treatment planning, radiation fields were designed to irradiate the head, thorax, or abdomen of the animal. Thermoluminescent dosimeters (TLDs) were used to confirm the treatment planning dosimetry for primary beam and scattered radiation. Results: Mice are efficiently placed into 60 ml syringes and immobilized, without the use of anesthetics. Although partial rotational movement around the longitudinal axis and a minor 2 mm forward/backward movement are permitted, this does not compromise the irradiation of the chosen body area. TLDs confirmed the dose values predicted by the treatment planning dosimetry, both for primary beam and scattered radiation. Conclusions: The customized PMMA apparatus described and validated is cost-effective, convenient to use, and efficient in performing PBI without the use of anesthesia. The developed apparatus permits the isolated irradiation of the mouse head, thorax, and abdomen. Importantly, the apparatus allows the delivery of PBI to five mice, simultaneously, representing an efficient way to effectively expose a large number of animals to PBI through multiple daily fractions, simulating clinical radiotherapy treatment schedules.« less

Photovoltaic performance and the energy landscape of CH3NH3PbI3.

PubMed

Zhou, Yecheng; Huang, Fuzhi; Cheng, Yi-Bing; Gray-Weale, Angus

2015-09-21

Photovoltaic cells with absorbing layers of certain perovskites have power conversion efficiencies up to 20%. Among these materials, CH3NH3PbI3 is widely used. Here we use density-functional theory to calculate the energies and rotational energy barriers of a methylammonium ion in the α or β phase of CH3NH3PbI3 with differently oriented neighbouring methylammonium ions. Our results suggest the methylammonium ions in CH3NH3PbI3 prefer to rotate collectively, and to be parallel to their neighbours. Changes in polarization on rotation of methylammonium ions are two to three times larger than those on relaxation of the lead ion from the centre of its coordination shell. The preferences for parallel configuration and concerted rotation, with the polarisation changes, are consistent with ferroelectricity in the material, and indicate that this polarisation is governed by methylammonium orientational correlations. We show that the field due to this polarisation is strong enough to screen the field hindering charge transport, and find this screening field in agreement with experiment. We examine two possible mechanisms for the effect of methylammonium ion rotation on photovoltaic performance. One is that rearrangement of methylammoniums promotes the creation and transport of charge carriers. Some effective masses change greatly, but changes in band structure with methylammonium rotation are not large enough to explain current-voltage hysteresis behaviour. The second possible mechanism is that polarization screens the hindering electric field, which arises from charge accumulation in the transport layers. Polarization changes on methylammonium rotation favour this second mechanism, suggesting that collective reorientation of methylammonium ions in the bulk crystal are in significant part responsible for the hysteresis and power conversion characteristics of CH3NH3PbI3 photovoltaic cells.

CsI Pre-Intercalation in the Inorganic Framework for Efficient and Stable FA1-x Csx PbI3 (Cl) Perovskite Solar Cells.

PubMed

Zhou, Ning; Shen, Yiheng; Zhang, Yu; Xu, Ziqi; Zheng, Guanhaojie; Li, Liang; Chen, Qi; Zhou, Huanping

2017-06-01

Engineering the chemical composition of organic and inorganic hybrid perovskite materials is one of the most feasible methods to boost the efficiency of perovskite solar cells with improved device stability. Among the diverse hybrid perovskite family of ABX 3 , formamidinium (FA)-based mixed perovskite (e.g., FA 1- x Cs x PbI 3 ) possesses optimum bandgaps, superior optoelectronic property, as well as thermal- and photostability, which is proven to be the most promising candidate for advanced solar cell. Here, FA 0.9 Cs 0.1 PbI 3 (Cl) is implemented as the light-harvesting layer in planar devices, whereas a low temperature, two-step solution deposition method is employed for the first time in this materials system. This paper comprehensively exploits the role of Cs + in the FA 0.9 Cs 0.1 PbI 3 (Cl) perovskite that affects the precursor chemistry, film nucleation and grain growth, and defect property via pre-intercalation of CsI in the inorganic framework. In addition, the resultant FA 0.9 Cs 0.1 PbI 3 (Cl) films are demonstrated to exhibit an improved optoelectronic property with an elevated device power conversion efficiency (PCE) of 18.6%, as well as a stable phase with substantial enhancement in humidity and thermal stability, as compared to that of FAPbI 3 (Cl). The present method is able to be further extended to a more complicated (FA,MA,Cs)PbX 3 material system by delivering a PCE of 19.8%. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Technical Note: Partial body irradiation of mice using a customized PMMA apparatus and a clinical 3D planning/LINAC radiotherapy system.

PubMed

Karagounis, Ilias V; Abatzoglou, Ioannis M; Koukourakis, Michael I

2016-05-01

In vivo radiobiology experiments involving partial body irradiation (PBI) of mice are of major importance because they allow for the evaluation of individual organ tolerance; overcoming current limitations of experiments using lower dose, whole body irradiation. In the current study, the authors characterize and validate an effective and efficient apparatus for multiple animal PBI, directed to the head, thorax, or abdomen of mice. The apparatus is made of polymethylmethacrylate and consists of a rectangular parallelepiped prism (40 cm × 16 cm × 8 cm), in which five holes were drilled to accomodate standard 60 ml syringes, each housing an unanesthetized, fully immobilized mouse. Following CT-scanning and radiotherapy treatment planning, radiation fields were designed to irradiate the head, thorax, or abdomen of the animal. Thermoluminescent dosimeters (TLDs) were used to confirm the treatment planning dosimetry for primary beam and scattered radiation. Mice are efficiently placed into 60 ml syringes and immobilized, without the use of anesthetics. Although partial rotational movement around the longitudinal axis and a minor 2 mm forward/backward movement are permitted, this does not compromise the irradiation of the chosen body area. TLDs confirmed the dose values predicted by the treatment planning dosimetry, both for primary beam and scattered radiation. The customized PMMA apparatus described and validated is cost-effective, convenient to use, and efficient in performing PBI without the use of anesthesia. The developed apparatus permits the isolated irradiation of the mouse head, thorax, and abdomen. Importantly, the apparatus allows the delivery of PBI to five mice, simultaneously, representing an efficient way to effectively expose a large number of animals to PBI through multiple daily fractions, simulating clinical radiotherapy treatment schedules.

Brief Motivational and Parent Interventions For College Students: A Randomized Factorial Study

PubMed Central

Wood, Mark D.; Fairlie, Anne M.; Fernandez, Anne C.; Borsari, Brian; Capone, Christy; Laforge, Robert; Carmona-Barros, Rosa

2010-01-01

Objective Using a randomized factorial design, we examined the efficacy of a Brief Motivational Intervention (BMI) and Parent-based Intervention (PBI) as universal preventive interventions to reduce alcohol use among incoming college students. Method Participants (N = 1,014) were assessed prior to matriculation and at 10-months and 22-months post-baseline. Two-part latent growth modeling was used to simultaneously examine initiation and growth in heavy episodic drinking and alcohol-related consequences. Results This study retained 90.8% (n = 921) of randomized students at the 10 month follow-up and 84.0% (n = 852) at the 22-month follow-up. BMI participants were significantly less likely than non-BMI participants to initiate heavy episodic drinking and to begin experiencing alcohol-related consequences. Effect sizes were minimal at 10-months (Cohen’s h ranged from 0.02–0.07) and small at 22-months (h’s from 0.15–0.22). A significant BMI X PBI interaction revealed that students receiving both the BMI and PBI were significantly less likely to report the onset of consequences beyond the sum of the individual intervention effects (h = 0.08 at 10-month and 0.21 at 22-month). Hypothesized direct BMI effects for reductions in heavy episodic drinking and consequences were not observed. Significant mediated effects via changes in descriptive norms were present for both growth and initiation of heavy episodic drinking and consequences. Conclusions To our knowledge, the current study is the first to provide support for BMI as a universal preventive intervention for incoming college students. While hypothesized PBI main effects were not found, mediation analyses suggest future refinements could enhance PBI effectiveness. PMID:20515210

Precise Morphology Control and Continuous Fabrication of Perovskite Solar Cells Using Droplet-Controllable Electrospray Coating System.

PubMed

Hong, Seung Chan; Lee, Gunhee; Ha, Kyungyeon; Yoon, Jungjin; Ahn, Namyoung; Cho, Woohyung; Park, Mincheol; Choi, Mansoo

2017-03-08

Herein, we developed a novel electrospray coating system for continuous fabrication of perovskite solar cells with high performance. Our system can systemically control the size of CH 3 NH 3 PbI 3 precursor droplets by modulating the applied electrical potential, shown to be a crucial factor for the formation of perovskite films. As a result, we have obtained pinhole-free and large grain-sized perovskite solar cells, yielding the best PCE of 13.27% with little photocurrent hysteresis. Furthermore, the average PCE through the continuous coating process was 11.56 ± 0.52%. Our system demonstrates not only the high reproducibility but also a new way to commercialize high-quality perovskite solar cells.

ISS Expedition 18 Multi Purpose Logistics Module (MPLM) Interior

NASA Image and Video Library

2008-11-19

ISS018-E-009225 (18 Nov. 2008) --- Astronaut Shane Kimbrough, STS-126 mission specialist, floats in the Leonardo Multi-Purpose Logistics Module attached to the Earth-facing port of the International Space Station's Harmony node while Space Shuttle Endeavour is docked with the station.

ISS Expedition 18 Multi Purpose Logistics Module (MPLM) Interior

NASA Image and Video Library

2008-11-19

ISS018-E-009227 (18 Nov. 2008) --- Astronaut Donald Pettit, STS-126 mission specialist, floats in the Leonardo Multi-Purpose Logistics Module attached to the Earth-facing port of the International Space Station's Harmony node while Space Shuttle Endeavour is docked with the station.

Trace impurities analysis determined by neutron activation in the PbI 2 crystal semiconductor

NASA Astrophysics Data System (ADS)

Hamada, M. M.; Oliveira, I. B.; Armelin, M. J.; Mesquita, C. H.

2003-06-01

In this work, a methodology for impurity analysis of PbI 2 was studied to investigate the effectiveness of the purification. Commercial salts were purified by the multi passes zone refining and grown by the Bridgman method. To evaluate the purification efficiency, samples from the bottom, middle and upper sections of the ZR ingot were analyzed after 200, 300 and 500 purification passes, by measurements of the impurity concentrations, using the neutron activation analysis (NAA) technique. There was a significant reduction of the impurities according to the purification numbers. The reduction efficiency was different for each element, namely: Au>Mn>Co˜Ag>K˜Br. The impurity concentration of the crystals grown after 200, 300 and 500 passes and the PbI 2 starting material were analyzed by NAA and plasma optical emission spectroscopy.

Polybenzimidazole membranes for direct methanol fuel cell: Acid-doped or alkali-doped?

NASA Astrophysics Data System (ADS)

Li, Long-Yun; Yu, Bor-Chern; Shih, Chao-Ming; Lue, Shingjiang Jessie

2015-08-01

Polybenzimidazole (PBI) films immersed in 2 M phosphoric acid (H3PO4) or 6 M potassium hydroxide (KOH) solution form electrolytes for conducting proton or hydroxide, respectively. A direct methanol fuel cell (DMFC) with the alkali-KOH doped PBI gives 117.9 mW cm-2 of power output which is more than 2 times greater than the power density of 46.5 mW cm-2 with the H3PO4-doped PBI (vs.) when both of the DMFCs use a micro porous layer (MPL) in a gas-fed cathode and a MPL-free anode and are operated at 90 °C. When the MPL-free anode and cathode are used and the fuel flow rate is tripled, the peak power density of alkaline DMFC reaches 158.9 mW cm-2.

A power pack based on organometallic perovskite solar cell and supercapacitor.

PubMed

Xu, Xiaobao; Li, Shaohui; Zhang, Hua; Shen, Yan; Zakeeruddin, Shaik M; Graetzel, Michael; Cheng, Yi-Bing; Wang, Mingkui

2015-02-24

We present an investigation on a power pack combining a CH3NH3PbI3-based solar cell with a polypyrrole-based supercapacitor and evaluate its performance as an energy pack. The package achieved an energy storage efficiency of 10%, which is much higher than that of other systems combining a PV cell with a supercapacitor. We find a high output voltage of 1.45 V for the device under AM 1.5G illumination when the CH3NH3PbI3-based solar cell is connected in series with a polypyrrole-based supercapacitor. This system affords continuous output of electric power by using CH3NH3PbI3-based solar cell as an energy source mitigating transients caused by light intensity fluctuations or the diurnal cycle.

Phonon Mode Transformation across the Orthohombic-Tetragonal Phase Transition in a Lead-Iodide Perovskite CH3NH3PbI3: a Terahertz Time-Domain Spectroscopy Approach

NASA Astrophysics Data System (ADS)

Chia, Elbert E. M.; La-O-Vorakiat, Chan; Kadro, Jeannette; Salim, Teddy; Zhao, Daming; Ahmed, Towfiq; Lam, Yeng Ming; Zhu, Jian-Xin; Marcus, Rudolph; Michel-Beyerle, Maria-Elisabeth

Using terahertz time-domain spectroscopy (THz-TDS), we study the temperature-dependent phonon modes of the organometallic lead iodide perovskite CH3NH3PbI3 thin film across the terahertz (0.5-3 THz) and temperature (20-300 K) ranges. These modes are related to the vibration of the Pb-I bonds. We found that two phonon modes in the tetragonal phase at room temperature split into four modes in the low-temperature orthorhombic phase. By use of the Lorentz model fitting, we analyze the critical behavior of this phase transition. King Mongkut's University of Technology Thonburi (Grant No. SCI58-003), Singapore MOE Tier 1 (RG13/12, RG123/14), ONR, ARO, NTU Biophysics Center, LANL LDRD, LANL CINT.

Low density lipoprotein levels linkage with the periodontal status patients of coronary heart disease

NASA Astrophysics Data System (ADS)

Ahmad, Nafisah Ibrahim; Masulili, Sri Lelyati C.; Lessang, Robert; Radi, Basuni

2017-02-01

Studies found an association between periodontitis and coronary heart disease (CHD), but relationship between periodontal status CHD patients with LDL (Low Density Lipoprotein) levels, as risk factors for atherosclerosis, has not been studied. Objective: To analyze relationship between LDL and periodontal status CHD. Methods: Periodontal status of 60 CHD, 40 controls were examined (PBI, PPD, CAL) and their blood was taken to assess levels of LDL. Result: Found significant differences LDL (p=0.005), correlation between LDL with PPD (p=0.003) and CAL CHD (p=0.013), and PPD (p=0.001), CAL (p=0.008) non-CHD, but no significant correlation between LDL with PBI CAD (p=0.689) and PBI non-CHD (p=0.320). Conclusion: There is a correlation between the LDL levels with periodontal status.

Paternal and maternal bonding styles in childhood are associated with the prevalence of chronic pain in a general adult population: the Hisayama Study.

PubMed

Anno, Kozo; Shibata, Mao; Ninomiya, Toshiharu; Iwaki, Rie; Kawata, Hiroshi; Sawamoto, Ryoko; Kubo, Chiharu; Kiyohara, Yutaka; Sudo, Nobuyuki; Hosoi, Masako

2015-07-31

Previous research has suggested that extraordinary adverse experiences during childhood, such as abuse, are possible risk factors for the development of chronic pain. However, the relationship between the perceived parental bonding style during childhood and chronic pain has been much less studied. In this cross-sectional study, 760 community-dwelling Japanese adults were asked if they had pain that had been present for six months or more. They completed the Parental Bonding Instrument (PBI), a self-administrated questionnaire designed to assess perceived parental bonding, and the Patient Health Questionnaire-9 to assess current depressive symptoms. The PBI consists of care and overprotection subscales that are analyzed by assigning the parental bonding style to one of four quadrants: Optimal bonding (high care/low overprotection), neglectful parenting (low care/low overprotection), affectionate constraint (high care/high overprotection), and affectionless control (low care/high overprotection). Logistic regression analysis was done to estimate the contribution of the parental bonding style to the risk of chronic pain, controlling for demographic variables. Compared to the optimal bonding group, the odds ratios (ORs) for having chronic pain were significantly higher in the affectionless control group for paternal bonding (OR: 2.21, 95% CI: 1.50-3.27) and for maternal bonding (OR: 1.60, 95% CI: 1.09-2.36). After adjusting for depression, significance remained only for paternal bonding. The results demonstrate that the parental bonding style during childhood is associated with the prevalence of chronic pain in adults in the general population and that the association is more robust for paternal bonding than for maternal bonding.

KSC-07pd0900

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- After a welcoming ceremony for the Experiment Logistics Module Pressurized Section of the Japanese Experiment Module, astronaut Takao Doi (right) talks with Kumiko Tanabe, a public affairs representative of the Japanese Aerospace and Exploration Agency. The logistics module will be delivered to the space station on mission STS-123. Doi is a crew member on that mission.The module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

Development of Japanese experiment module remote manipulator system

NASA Technical Reports Server (NTRS)

Matsueda, Tatsuo; Kuwao, Fumihiro; Motohasi, Shoichi; Okamura, Ryo

1994-01-01

National Space Development Agency of Japan (NASDA) is developing the Japanese Experiment Module (JEM), as its contribution to the International Space Station. The JEM consists of the pressurized module (PM), the exposed facility (EF), the experiment logistics module pressurized section (ELM-PS), the experiment logistics module exposed section (ELM-ES) and the Remote Manipulator System (RMS). The JEMRMS services for the JEM EF, which is a space experiment platform, consists of the Main Arm (MA), the Small Fine Arm (SFA) and the RMS console. The MA handles the JEM EF payloads, the SFA and the JEM element, such as ELM-ES.

Monitoring a Silent Phase Transition in CH 3NH 3PbI 3 Solar Cells via Operando X-ray Diffraction

DOE PAGES

Schelhas, Laura T.; Christians, Jeffrey A.; Berry, Joseph J.; ...

2016-10-13

The relatively modest temperature of the tetragonal-to-cubic phase transition in CH 3NH 3PbI 3 perovskite is likely to occur during real world operation of CH 3NH 3PbI 3 solar cells. In this work, we simultaneously monitor the structural phase transition of the active layer along with solar cell performance as a function of the device operating temperature. The tetragonal to cubic phase transition is observed in the working device to occur reversibly at temperatures between 60.5 and 65.4 degrees C. In these operando measurements, no discontinuity in the device performance is observed, indicating electronic behavior that is insensitive to themore » structural phase transition. Here, this decoupling of device performance from the change in long-range order across the phase transition suggests that the optoelectronic properties are primarily determined by the local structure in CH 3NH 3PbI 3. That is, while the average crystal structure as probed by X-ray diffraction shows a transition from tetragonal to cubic, the local structure generally remains well characterized by uncorrelated, dynamic octahedral rotations that order at elevated temperatures but are unchanged locally.« less

Light-Independent Ionic Transport in Inorganic Perovskite and Ultrastable Cs-Based Perovskite Solar Cells.

PubMed

Zhou, Wenke; Zhao, Yicheng; Zhou, Xu; Fu, Rui; Li, Qi; Zhao, Yao; Liu, Kaihui; Yu, Dapeng; Zhao, Qing

2017-09-07

Due to light-induced effects in CH 3 NH 3 -based perovskites, such as ion migration, defects formation, and halide segregation, the degradation of CH 3 NH 3 -based perovskite solar cells under maximum power point is generally implicated. Here we demonstrated that the effect of light-enhanced ion migration in CH 3 NH 3 PbI 3 can be eliminated by inorganic Cs substitution, leading to an ultrastable perovskite solar cell. Quantitatively, the ion migration barrier for CH 3 NH 3 PbI 3 is 0.62 eV under dark conditions, larger than that of CsPbI 2 Br (0.45 eV); however, it reduces to 0.07 eV for CH 3 NH 3 PbI 3 under illumination, smaller than that for CsPbI 2 Br (0.43 eV). Meanwhile, photoinduced halide segregation is also suppressed in Cs-based perovskites. Cs-based perovskite solar cells retained >99% of the initial efficiency (10.3%) after 1500 h of maximum power point tracking under AM1.5G illumination, while CH 3 NH 3 PbI 3 solar cells degraded severely after 50 h of operation. Our work reveals an uncovered mechanism for stability improvement by inorganic cation substitution in perovskite-based optoelectronic devices.

Monitoring a Silent Phase Transition in CH 3NH 3PbI 3 Solar Cells via Operando X-ray Diffraction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schelhas, Laura T.; Christians, Jeffrey A.; Berry, Joseph J.

The relatively modest temperature of the tetragonal-to-cubic phase transition in CH 3NH 3PbI 3 perovskite is likely to occur during real world operation of CH 3NH 3PbI 3 solar cells. In this work, we simultaneously monitor the structural phase transition of the active layer along with solar cell performance as a function of the device operating temperature. The tetragonal to cubic phase transition is observed in the working device to occur reversibly at temperatures between 60.5 and 65.4 degrees C. In these operando measurements, no discontinuity in the device performance is observed, indicating electronic behavior that is insensitive to themore » structural phase transition. Here, this decoupling of device performance from the change in long-range order across the phase transition suggests that the optoelectronic properties are primarily determined by the local structure in CH 3NH 3PbI 3. That is, while the average crystal structure as probed by X-ray diffraction shows a transition from tetragonal to cubic, the local structure generally remains well characterized by uncorrelated, dynamic octahedral rotations that order at elevated temperatures but are unchanged locally.« less

Short-length and high-density TiO2 nanorod arrays for the efficient charge separation interface in perovskite solar cells

NASA Astrophysics Data System (ADS)

Xiao, Guannan; Shi, Chengwu; Zhang, Zhengguo; Li, Nannan; Li, Long

2017-05-01

The TiO2 nanorod arrays with the length of 70 nm, the diameter of 20 nm, and the areal density of 1000 μm-2 were firstly prepared by the hydrothermal method using the aqueous grown solution of 38 mM titanium isopropoxide and 6 M hydrochloric acid at 170 °C for 60 min. Over-500 nm-thickness CH3NH3PbI3-xBrx absorber layers were successfully obtained by sequential deposition routes using 1.7 M PbI2·DMSO complex precursor solution and 0.465 M isopropanol solution of the methylammonium halide mixture with the molar ratio of CH3NH3I/CH3NH3Br=85/15. The perovskite solar cells based on the TiO2 nanorod array and 560 nm-thickness CH3NH3PbI3-xBrx absorber layer exhibited the best photoelectric conversion efficiency (PCE) of 15.93%, while the corresponding planar perovskite solar cells without the TiO2 nanorod array and with 530 nm-thickness CH3NH3PbI3-xBrx absorber layer gave the best PCE of 12.82% at the relative humidity of 50-54%.

Age of drinking onset as a moderator of the efficacy of parent-based, brief motivational, and combined intervention approaches to reduce drinking and consequences among college students.

PubMed

Mallett, Kimberly A; Ray, Anne E; Turrisi, Rob; Belden, Calum; Bachrach, Rachel L; Larimer, Mary E

2010-07-01

The current study tested age of onset as a moderator of intervention efficacy on drinking and consequence outcomes among a high-risk population of college students (i.e., former high school athletes). Students were randomized to one of four conditions: assessment only control, combined parent-based intervention (PBI) and brief motivational intervention (BMI), PBI alone, and BMI alone. Participants (n = 1,275) completed web-administered measures at baseline (summer before starting college) and 10-month follow-up. Overall, the combined intervention demonstrated the strongest and most consistent reductions across all outcomes, particularly with the youngest initiators. Participants who initiated drinking at the youngest ages had significantly lower peak drinking, typical weekly drinking, and reported consequences at follow-up when they received the combined intervention when compared to the control group. The BMI and PBI groups, when examined independently, demonstrated significant effects across outcomes but were inconsistent across the different age groups. Results suggest the combination of a PBI and a peer-delivered BMI is an appropriate and efficacious way to reduce drinking and related consequences among individuals who initiated drinking earlier in adolescence and are at an increased risk of experiencing alcohol problems.

Connecting the solution chemistry of PbI2 and MAI: a cyclodextrin-based supramolecular approach to the formation of hybrid halide perovskites.

PubMed

Masi, Sofia; Aiello, Federica; Listorti, Andrea; Balzano, Federica; Altamura, Davide; Giannini, Cinzia; Caliandro, Rocco; Uccello-Barretta, Gloria; Rizzo, Aurora; Colella, Silvia

2018-03-28

The evolution from solvated precursors to hybrid halide perovskite films dictates most of the photophysical and optoelectronic properties of the final polycrystalline material. Specifically, the complex equilibria and the importantly different solubilities of lead iodide (PbI 2 ) and methylammonium iodide (MAI) induce inhomogeneous crystal growth, often leading to a defect dense film showing non-optimal optoelectronic properties and intrinsic instability. Here, we explore a supramolecular approach based on the use of cyclodextrins (CDs) to modify the underlying solution chemistry. The peculiar phenomenon demonstrated is a tunable complexation between different CDs and MA + cations concurrent to an out of cage PbI 2 intercalation, representing the first report of a connection between the solvation equilibria of the two perovskite precursors. The optimal conditions in terms of CD cavity size and polarity translate to a neat enhancement of PbI 2 solubility in the reaction media, leading to an equilibration of the availability of the precursors in solution. The macroscopic result of this is an improved nucleation process, leading to a perovskite material with higher crystallinity, better optical properties and improved moisture resistance. Remarkably, the use of CDs presents a great potential for a wide range of device-related applications, as well as for the development of tailored composite materials.

Multipurpose Logistics Module, Leonardo, Rests in Discovery's Payload Bay

NASA Technical Reports Server (NTRS)

2001-01-01

This in-orbit close up shows the Italian Space Agency-built multipurpose Logistics Module (MPLM), Leonardo, the primary cargo of the STS-102 mission, resting in the payload bay of the Space Shuttle Orbiter Discovery. The Leonardo MPLM is the first of three such pressurized modules that will serve as the International Space Station's (ISS') moving vans, carrying laboratory racks filled with equipment, experiments, and supplies to and from the Station aboard the Space Shuttle. The cylindrical module is approximately 21-feet long and 15- feet in diameter, weighing almost 4.5 tons. It can carry up to 10 tons of cargo in 16 standard Space Station equipment racks. Of the 16 racks the module can carry, 5 can be furnished with power, data, and fluid to support refrigerators or freezers. In order to function as an attached station module as well as a cargo transport, the logistics module also includes components that provide life support, fire detection and suppression, electrical distribution, and computer functions. The eighth station assembly flight and NASA's 103rd overall flight, STS-102 launched March 8, 2001 for an almost 13 day mission.

KENNEDY SPACE CENTER, FLA. - STS-120 Mission Specialists Piers Sellers and Michael Foreman look at the Japanese Experiment Module (JEM) Pressurized Module located in the Space Station Processing Facility. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the JEM, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

NASA Image and Video Library

2003-07-18

KENNEDY SPACE CENTER, FLA. - STS-120 Mission Specialists Piers Sellers and Michael Foreman look at the Japanese Experiment Module (JEM) Pressurized Module located in the Space Station Processing Facility. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the JEM, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-120 Mission Specialist Piers Sellers looks over the Japanese Experiment Module (JEM) Pressurized Module. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

NASA Image and Video Library

2003-07-18

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-120 Mission Specialist Piers Sellers looks over the Japanese Experiment Module (JEM) Pressurized Module. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-120 Mission Specialist Michael Foreman looks over the Japanese Experiment Module (JEM) Pressurized Module. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

NASA Image and Video Library

2003-07-18

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-120 Mission Specialist Michael Foreman looks over the Japanese Experiment Module (JEM) Pressurized Module. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. The STS-120 mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

Usachev in Raffaello Multi-Purpose Logistics Module (MPLM)

NASA Image and Video Library

2001-04-26

ISS002-E-5852 (26 April 2001) --- Yury V. Usachev of Rosaviakosmos, Expedtion Two mission commander, enjoys the extra space provided by the Multipurpose Logistics Module (MPLM) Raphaello which was mated to the International Space Station (ISS) during the STS-100 mission. The image was taken with a digital still camera.

Insulation Reformulation Development

NASA Technical Reports Server (NTRS)

Chapman, Cynthia; Bray, Mark

2015-01-01

The current Space Launch System (SLS) internal solid rocket motor insulation, polybenzimidazole acrylonitrile butadiene rubber (PBI-NBR), is a new insulation that replaced asbestos-based insulations found in Space Shuttle heritage solid rocket boosters. PBI-NBR has some outstanding characteristics such as an excellent thermal erosion resistance, low thermal conductivity, and low density. PBI-NBR also has some significant challenges associated with its use: Air entrainment/entrapment during manufacture and lay-up/cure and low mechanical properties such as tensile strength, modulus, and fracture toughness. This technology development attempted to overcome these challenges by testing various reformulated versions of booster insulation. The results suggest the SLS program should continue to investigate material alternatives for potential block upgrades or use an entirely new, more advanced booster. The experimental design was composed of a logic path that performs iterative formulation and testing in order to maximize the effort. A lab mixing baseline was developed and documented for the Rubber Laboratory in Bldg. 4602/Room 1178.

Efficient non-doped phosphorescent orange, blue and white organic light-emitting devices

NASA Astrophysics Data System (ADS)

Yin, Yongming; Yu, Jing; Cao, Hongtao; Zhang, Letian; Sun, Haizhu; Xie, Wenfa

2014-10-01

Efficient phosphorescent orange, blue and white organic light-emitting devices (OLEDs) with non-doped emissive layers were successfully fabricated. Conventional blue phosphorescent emitters bis [4,6-di-fluorophenyl]-pyridinato-N,C2'] picolinate (Firpic) and Bis(2,4-difluorophenylpyridinato) (Fir6) were adopted to fabricate non-doped blue OLEDs, which exhibited maximum current efficiency of 7.6 and 4.6 cd/A for Firpic and Fir6 based devices, respectively. Non-doped orange OLED was fabricated utilizing the newly reported phosphorescent material iridium (III) (pbi)2Ir(biq), of which manifested maximum current and power efficiency of 8.2 cd/A and 7.8 lm/W. The non-doped white OLEDs were achieved by simply combining Firpic or Fir6 with a 2-nm (pbi)2Ir(biq). The maximum current and power efficiency of the Firpic and (pbi)2Ir(biq) based white OLED were 14.8 cd/A and 17.9 lm/W.

Controlling Photoconductivity in PBI Films by Supramolecular Assembly.

PubMed

Draper, Emily R; Archibald, Lewis J; Nolan, Michael C; Schweins, Ralf; Zwijnenburg, Martijn A; Sproules, Stephen; Adams, Dave J

2018-03-15

Perylene bisimides (PBIs) self-assemble in solution. The solubility of the PBIs is commonly changed through the choice of substituents at the imide positions. It is generally assumed this substitution does not affect the electronic properties of the PBI, and that the properties of the self-assembled aggregate are essentially that of the isolated molecule. However, substituents do affect the self-assembly, resulting in potentially different packing in the formed aggregates. Here, we show that the photoconductivity of films formed from a library of substituted PBIs varies strongly with the substituent and demonstrate that this is due to the different ways in which they pack. Our results open the possibility for tuning the optoelectronic properties of self-assembled PBIs by controlling the aggregate structure through careful choice of substituent, as demonstrated by us here optimising the photoconductivity of PBI films in this way. © 2018 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Controlling Photoconductivity in PBI Films by Supramolecular Assembly

PubMed Central

Archibald, Lewis J.; Nolan, Michael C.; Schweins, Ralf; Zwijnenburg, Martijn A.; Sproules, Stephen

2018-01-01

Abstract Perylene bisimides (PBIs) self‐assemble in solution. The solubility of the PBIs is commonly changed through the choice of substituents at the imide positions. It is generally assumed this substitution does not affect the electronic properties of the PBI, and that the properties of the self‐assembled aggregate are essentially that of the isolated molecule. However, substituents do affect the self‐assembly, resulting in potentially different packing in the formed aggregates. Here, we show that the photoconductivity of films formed from a library of substituted PBIs varies strongly with the substituent and demonstrate that this is due to the different ways in which they pack. Our results open the possibility for tuning the optoelectronic properties of self‐assembled PBIs by controlling the aggregate structure through careful choice of substituent, as demonstrated by us here optimising the photoconductivity of PBI films in this way. PMID:29405458

Dealing with the Surgical and Medical Challenges of Penetrating Brain Injuries

PubMed Central

Syrmos, Nikolaos; Ganau, Mario; De Carlo, Antonella; Prisco, Lara; Ganau, Laura; Valadakis, Vasileios; Grigoriou, Kostantinos; Iliadis, Charalampos; Arvanitakis, Dimitrios

2013-01-01

Peacetime has reduced the overall incidence of penetrating brain injuries (PBI), and those related to missile penetration are not common anymore at least in western countries. Nevertheless, PBI still occur, and car crashes or work accidents are their main causes. The management of such cases is characterized by many challenges, not only from a surgical and medical point of view, but also for the different and sometimes bizarre dynamics by which they present. Herein we report an unusual deep penetrating brain injury, due to a high-energy crash against a metallic rod in a construction site, with a good surgical outcome despite dramatic clinical conditions on admission. A discussion of the surgical results and functional outcome related to PBI, as found in the English medical literature, is provided. Moreover the most common postoperative complications along with the diagnostic flow charts and therapeutic options useful to prevent inappropriate treatment are highlighted. PMID:23365777

Power generation from nanostructured PbTe-based thermoelectrics: comprehensive development from materials to modules

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hu, Xiaokai; Jood, Priyanka; Ohta, Michihiro

2016-01-01

In this work, we demonstrate the use of high performance nanostructured PbTe-based materials in high conversion efficiency thermoelectric modules. We fabricated the samples of PbTe-2% MgTe doped with 4% Na and PbTe doped with 0.2% PbI2 with high thermoelectric figure of merit (ZT) and sintered them with Co-Fe diffusion barriers for use as p- and n-type thermoelectric legs, respectively. Transmission electron microscopy of the PbTe legs reveals two shapes of nanostructures, disk-like and spherical. The reduction in lattice thermal conductivity through nanostructuring gives a ZT of similar to 1.8 at 810 K for p-type PbTe and similar to 1.4 atmore » 750 K for n-type PbTe. Nanostructured PbTe-based module and segmented-leg module using Bi2Te3 and nanostructured PbTe were fabricated and tested with hot-side temperatures up to 873 K in a vacuum. The maximum conversion efficiency of similar to 8.8% for a temperature difference (Delta T) of 570 K and B11% for a Delta T of 590 K have been demonstrated in the nanostructured PbTe-based module and segmented Bi2Te3/nanostructured PbTe module, respectively. Three-dimensional finite-element simulations predict that the maximum conversion efficiency of the nanostructured PbTe-based module and segmented Bi2Te3/nanostructured PbTe module reaches 12.2% for a Delta T of 570 K and 15.6% for a Delta T of 590 K respectively, which could be achieved if the electrical and thermal contact between the nanostructured PbTe legs and Cu interconnecting electrodes is further improved.« less

Work continues on Leonardo, the Multi-Purpose Logistics Module, in the Space Station Processing Faci

NASA Technical Reports Server (NTRS)

1999-01-01

Workers in the Space Station Processing Facility work on Leonardo, the Multipurpose Logistics Module (MPLM) built by the Agenzia Spaziale Italiana (ASI). The MPLM, a reusable logistics carrier, will be the primary delivery system used to resupply and return International Space Station cargo requiring a pressurized environment. Leonardo is the first of three MPLM carriers for the International Space Station. It is scheduled to be launched on Space Shuttle Mission STS-102, targeted for June 2000. Leonardo shares space in the SSPF with the Shuttle Radar Topography Mission (SRTM), targeted for launch in September 1999, and Destiny, the U.S. Lab module, targeted for mission STS-98 in late April 2000.

Cost and logistics of implementing a tissue-based American College of Surgeons/Association of Program Directors in Surgery surgical skills curriculum for general surgery residents of all clinical years.

PubMed

Henry, Brandon; Clark, Philip; Sudan, Ranjan

2014-02-01

The cost and logistics of deploying the American College of Surgeons (ACS)/Association of Program Directors in Surgery (APDS) National Technical Skills Curriculum across all training years are not known. This information is essential for residency programs choosing to adopt similar curricula. A task force evaluated the authors' institution's existing simulation curriculum and enhanced it by implementing the ACS/APDS modules. A 35-module curriculum was administered to 35 general surgery residents across all 5 clinical years. The costs and logistics were noted, and resident satisfaction was assessed. The annual operational cost was $110,300 ($3,150 per resident). Cost per module, per resident was $940 for the cadaveric module compared with $220 and $240 for dry simulation and animal tissue-based modules, respectively. Resident satisfaction improved from 2.45 to 4.78 on a 5-point, Likert-type scale after implementing the ACS/APDS modules. The ACS/APDS skills curriculum was implemented successfully across all clinical years. Cadaveric modules were the most expensive. Animal and dry simulation modules were equivalent in cost. The addition of tissue-based modules was associated with high satisfaction. Copyright © 2014 Elsevier Inc. All rights reserved.

Logistics Modeling for Lunar Exploration Systems

NASA Technical Reports Server (NTRS)

Andraschko, Mark R.; Merrill, R. Gabe; Earle, Kevin D.

2008-01-01

The extensive logistics required to support extended crewed operations in space make effective modeling of logistics requirements and deployment critical to predicting the behavior of human lunar exploration systems. This paper discusses the software that has been developed as part of the Campaign Manifest Analysis Tool in support of strategic analysis activities under the Constellation Architecture Team - Lunar. The described logistics module enables definition of logistics requirements across multiple surface locations and allows for the transfer of logistics between those locations. A key feature of the module is the loading algorithm that is used to efficiently load logistics by type into carriers and then onto landers. Attention is given to the capabilities and limitations of this loading algorithm, particularly with regard to surface transfers. These capabilities are described within the context of the object-oriented software implementation, with details provided on the applicability of using this approach to model other human exploration scenarios. Some challenges of incorporating probabilistics into this type of logistics analysis model are discussed at a high level.

[The effect of emotional stressors on thyroid gland function].

PubMed

Pastukhov, N A

1975-01-01

Response of the normal and goiterous thyroid gland to the information on the forthcoming operation was studied in 12 patients with varicose veins of the lower limbs and in 67 patients with thyrotoxicosis; this was done by determination of protein-bound iodine (PBI). PBI proved to increase before the operation in both groups of the patients. Due to undesirable hyperfunction of the thyroid gland prior to the operation in thyrotoxicosis, the psychodepressive premedication component should be increased.

Macleya cordata and Prunella vulgaris in oral hygiene products - their efficacy in the control of gingivitis.

PubMed

Adámková, Hana; Vicar, Jaroslav; Palasová, Jirina; Ulrichová, Jitka; Simánek, Vilím

2004-07-01

A double-blind, placebo-controlled clinical trial was performed to investigate the effectiveness of a herbal-based dentifrice in the control of gingivitis. Forty volunteers completed the 84-day study. All subjects were balanced for parameters measured - plaque index (PI), community periodontal index of treatment needs (CPITN) and papillary bleeding index (PBI). The dentifrice was effective in reducing symptoms of gingivitis as evaluated by the CPITN and PBI indexes.

Iridium-catalyzed direct tetraborylation of perylene bisimides.

PubMed

Teraoka, Takuro; Hiroto, Satoru; Shinokubo, Hiroshi

2011-05-20

Treatment of perylene bisimides (PBIs) with bis(pinacolato)diboron in the presence of an iridium catalyst provides tetraborylated PBIs at 2,5,8,11-positions in good yields with perfect regioselectivity. The planar structure of the perylene core has been confirmed by X-ray diffraction analysis. Oxidation of tetraborylated PBI with hydroxylamine hydrochloride affords tetrahydroxy PBI in excellent yield, which exhibits a substantially blue-shifted absorption spectrum due to an intramolecular hydrogenbonding interaction between carbonyl and hydroxy groups.

Defining the Operational Conditions for High Temperature Polymer Fuel Cells in Naval Environments

DTIC Science & Technology

2008-12-31

benefits of both Proton Exchange Membrane Fuel Cells ( PEMFCs ) and phosphoric acid fuel cell technologies: a solid polymer electrolyte, the PBI...membrane, but with higher temperature (160°C) operation. PBI membrane technology is far less developed than that for PEMFCs , but it is rapidly emerging as...how air contaminants affect the properties of proton exchange membrane fuel cells ( PEMFCs ). PEMFCs operate at 80 °C, and are the present choice of fuel

CH3NH3PbI3 and CsPbI3 Supramolecular Clusters in 1D: Do They Evolve with the Same Principle of Cooperative Binding?

NASA Astrophysics Data System (ADS)

Varadwaj, Arpita; Varadwaj, Pradeep R.; Yamashita, Koichi

Development of novel semiconductor-based photo-catalytic and -voltaic systems is a major area of research in nanoscience and technologies, and engineering. The process can be either direct or indirect in converting the light energy into electricity. Some of the photovoltaics include the organic, dye-sensitized, and halide perovskite solar cells, among others. Methylammonium lead iodide (CH3NH3PbI3) inorganic-organic hybrid perovskite is one among the many highly valued semiconductors reported till date, comparable with the inorganic cesium lead iodide (CsPbI3) perovskite. These are competitive candidates in the solar energy race. Nevertheless, this study was concentrated on the fundamental understanding of the rational designs of the CH3NH3PbI3 and CsPbI3 supramolecular materials using first-principles calculations, emerged though the self-assembly of the respective building blocks. It therefore addresses the question whether the (CH3NH3PbI3)n and (CsPbI3)n (n =1-10) supramolecular clusters are the consequences of additivity, or non-additive cooperative binding? For addressing this question, the supramolecular properties such as the polarizability, the intermolecular charge transfer, and the binding energy, etc., all w.r.t the cluster size n, are exploited. CREST-JST, 7 Gobancho, Chiyoda-ku, Tokyo, Japan 102-0076.

Inhibition of Zero Drift in Perovskite-Based Photodetector Devices via [6,6]-Phenyl-C61-butyric Acid Methyl Ester Doping.

PubMed

Liu, Yintao; Jia, Renxu; Wang, Yucheng; Hu, Ziyang; Zhang, Yuming; Pang, Tiqiang; Zhu, Yuejin; Luan, Suzhen

2017-05-10

Zero drift can severely deteriorate the stability of the light-dark current ratio, detectivity, and responsivity of photodetectors. In this paper, the effects of a [6,6]-phenyl-C61-butyric acid methyl ester (PCBM)-doped perovskite-based photodetector device on the inhibition of zero drift under dark state are discussed. Two kinds of photodetectors (Au/CH 3 NH 3 PbI x Cl 3-x /Au and Au/CH 3 NH 3 PbI x Cl 3-x :PCBM/Au) were prepared, and the materials and photodetector devices were measured by scanning electron microscopy, X-ray diffraction, photoluminescence, ultraviolet absorption spectra, and current-voltage and current-time measurements. It was found that similar merit parameters, including light-dark current ratio (∼10 2 ), detectivity (∼10 11 Jones), and responsivity were obtained for these two kinds of photodetectors. However, the drift of Au/CH 3 NH 3 PbI x Cl 3-x :PCBM/Au devices is negligible, while a drift of ∼0.2 V exists in Au/CH 3 NH 3 PbI x Cl 3-x /Au devices. A new model is proposed based on the hindering theory of ion (vacancy) migration, and it is believed that the dopant PCBM can hinder the ion (vacancy) migration of perovskite materials to suppress the phenomenon of zero drift in perovskite-based photodetectors.

Hierarchical Self-Organization of Perylene Bisimides into Supramolecular Spheres and Periodic Arrays Thereof.

PubMed

Sahoo, Dipankar; Peterca, Mihai; Aqad, Emad; Partridge, Benjamin E; Heiney, Paul A; Graf, Robert; Spiess, Hans W; Zeng, Xiangbing; Percec, Virgil

2016-11-09

Perylene bisimide derivatives (PBIs) are known to form only columnar or lamellar assemblies. There is no known example of a PBI self-assembling into a supramolecular sphere. Therefore, periodic and quasiperiodic arrays generated from spherical assemblies produced from PBIs are also not known. Here, a PBI functionalized at its imide groups with a second generation self-assembling dendron is reported to self-assemble into supramolecular spheres. These spheres self-organize in a body-centered cubic (BCC) periodic array, rarely encountered for self-assembling dendrons but often encountered in block copolymers. These supramolecular spheres also assemble into a columnar hexagonal array in which the supramolecular columns are unexpectedly and unprecedentedly made from spheres. At lower temperature, two additional columnar hexagonal phases consisting of symmetric and asymmetric tetrameric crowns of PBI are observed. Structural and retrostructural analysis via X-ray diffraction (XRD), molecular modeling, molecular simulation, and solid state NMR suggests that inversion of the symmetric tetrameric crowns at high temperature mediates their transformation into supramolecular spheres. The tetrameric crowns of PBIs are able to form an isotropic sphere in the cubic phase due to rapid molecular motion at high temperature, unobservable by XRD but demonstrated by solid state NMR studies. This mechanism of hierarchical self-organization of PBI into supramolecular spheres is most probably general and can be applied to other related planar molecules to generate new functions.

Efficiency enhancement of perovskite solar cells using structural and morphological improvement of CH3NH3PbI3 absorber layers

NASA Astrophysics Data System (ADS)

Alidaei, Maryam; Izadifard, Morteza; Ghazi, Mohammad E.; Ahmadi, Vahid

2018-01-01

Perovskite solar cells have been heavily investigated due to their unique properties such as high power conversion efficiency (PCE), low-cost fabrication by solution processes, high diffusion length, large absorption coefficient, and direct and tunable band gap. PCE of perovskite devices is strongly dependent on the absorber layer properties such as morphology, crystallinity, and compactness, which are required to be optimized. In this work, the CH3NH3PbI3 (170-480 nm) absorber layers with various methylammonium iodine (MAI) concentrations (7, 10, 20 and 40 mg ml-1) and perovskite solar cells with the fluorine-doped tin oxide (400 nm)/C-TiO2 (30 nm)/Meso-TiO2 (400 nm)/CH3NH3PbI3 (170-480 nm)/P3HT (30 nm)/Au (100 nm) structure were fabricated. A two-step solution process was used for deposition of the CH3NH3PbI3 absorber layers. The morphology, crystal structure, and optical properties of the perovskite layer grown on glass and also the photovoltaic properties of the fabricated solar cells were studied. The results obtained showed that by controlling the deposition conditions, due to the reduction in charge recombination, PCE enhancement of the perovskite solar cell (up to 11.6%) was accessible.

STS-102 Onboard Photograph-Multi-Purpose Logistics Module, Leonardo

NASA Technical Reports Server (NTRS)

2001-01-01

A crewmember of Expedition One, cosmonaut Yuri P. Gidzenko, is dwarfed by transient hardware aboard Leonardo, the Italian Space Agency-built Multi-Purpose Logistics Module (MPLM), a primary cargo of the STS-102 mission. The Leonardo MPLM is the first of three such pressurized modules that will serve as the International Space Station's (ISS's) moving vans, carrying laboratory racks filled with equipment, experiments and supplies to and from the Space Station aboard the Space Shuttle. The cylindrical module is approximately 21-feet long and 15- feet in diameter, weighing almost 4.5 tons. It can carry up to 10 tons of cargo into 16 standard Space Station equipment racks. Of the 16 racks the module can carry, 5 can be furnished with power, data, and fluid to support refrigerators or freezers. In order to function as an attached station module as well as a cargo transport, the logistics module also includes components that provide life support, fire detection and suppression, electrical distribution, and computer functions. The eighth Shuttle mission to visit the ISS, the STS-102 mission served as a crew rotation flight. It delivered the Expedition Two crew to the Station and returned the Expedition One crew back to Earth.

Broadband Emission in Two-Dimensional Hybrid Perovskites: The Role of Structural Deformation.

PubMed

Cortecchia, Daniele; Neutzner, Stefanie; Srimath Kandada, Ajay Ram; Mosconi, Edoardo; Meggiolaro, Daniele; De Angelis, Filippo; Soci, Cesare; Petrozza, Annamaria

2017-01-11

Only a selected group of two-dimensional (2D) lead-halide perovskites shows a peculiar broad-band photoluminescence. Here we show that the structural distortions of the perovskite lattice can determine the defectivity of the material by modulating the defect formation energies. By selecting and comparing two archetype systems, namely, (NBT) 2 PbI 4 and (EDBE)PbI 4 perovskites (NBT = n-butylammonium and EDBE = 2,2-(ethylenedioxy)bis(ethylammonium)), we find that only the latter, subject to larger deformation of the Pb-X bond length and X-Pb-X bond angles, sees the formation of V F color centers whose radiative decay ultimately leads to broadened PL. These findings highlight the importance of structural engineering to control the optoelectronic properties of this class of soft materials.

Optical cryoimaging for assessment of radiation-induced injury to rat kidney metabolic state

NASA Astrophysics Data System (ADS)

Mehrvar, Shima; Funding la Cour, Mette; Medhora, Meetha; Camara, Amadou K. S.; Ranji, Mahsa

2018-02-01

Objective: This study utilizes fluorescence cryoimaging to quantitatively assess the effect of a high dose of irradiation on rat renal metabolism through redox state. Introduction: Exposure to high doses of irradiation could lead to death, in part, due to renal dysfunction. The kidney is one of the most sensitive organs that exhibit delayed injuries in survivors of acute radiation syndrome. In this study, optical cryoimaging was utilized to examine the potential for renal mitochondrial dysfunction after partial-body irradiation (PBI) and the mitigating effect of lisinopril-treatment, an angiotensin converting enzyme inhibitor that is FDA-approved for other indications. Materials and methods: Rats were exposed to a single dose of 13 Gy leg-out partial body irradiation (PBI, by X-rays). Rats (n = 5/group) received no further treatment, or lisinopril started one week after irradiation and continued at 24 mg/m2 /day. The non-irradiated siblings were used as controls. After 150 days, the rats were sacrificed, and their kidneys harvested and snap frozen in liquid nitrogen for later cryoimaging. The 3D images of metabolic indices (NADH and FAD) were captured, and the redox ratio i.e. NADH/FAD was calculated. The mitochondrial redox state of three groups of rat kidneys were quantified by calculating the volumetric mean of redox ratio images (RR). Results: 3D cryoimaging revealed that in PBI only kidneys, the metabolic marker (RR) decreased significantly by 78% compared to non-irradiated controls. Treatment with lisinopril significantly improved the RR by 93% in groups exposed to PBI. Conclusion: This study aimed at quantifying the level of the mitochondrial redox state of irradiated rat kidneys compared to non-irradiated kidneys (controls) and the efficacy of lisinopril to preserve kidney metabolism after irradiation. PBI oxidized the metabolic state of kidneys and lisinopril mitigated the radiation-induced injury on renal mitochondria.

The Raffaello, a Multi-Purpose Logistics Module, arrives at KSC aboard a Beluga super transporter

NASA Technical Reports Server (NTRS)

1999-01-01

An Airbus Industrie A300-600ST 'Beluga' Super Transporter touches down at the Shuttle Landing Facility to deliver its cargo, the second Multi-Purpose Logistics Module (MPLM) for the International Space Station (ISS). One of Italy's major contributions to the ISS program, the MPLM, named Raffaello, is a reusable logistics carrier and the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Weighing nearly 4.5 tons, the module measures 21 feet long and 15 feet in diameter. Raffaello will join Leonardo, the first Italian-built MPLM, in the Space Station Processing Facility for testing. NASA, Boeing, the Italian Space Agency and Alenia Aerospazio will provide engineering support.

The Raffaello, a Multi-Purpose Logistics Module, arrives at KSC aboard a Beluga super transporter

NASA Technical Reports Server (NTRS)

1999-01-01

An Airbus Industrie A300-600ST 'Beluga' Super Transporter lands in the rain at the Shuttle Landing Facility to deliver its cargo, the second Multi-Purpose Logistics Module (MPLM) for the International Space Station (ISS). One of Italy's major contributions to the ISS program, the MPLM, named Raffaello, is a reusable logistics carrier and the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Weighing nearly 4.5 tons, the module measures 21 feet long and 15 feet in diameter. Raffaello will join Leonardo, the first Italian-built MPLM, in the Space Station Processing Facility for testing. NASA, Boeing, the Italian Space Agency and Alenia Aerospazio will provide engineering support.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Gang; Kong, Lingping; Gong, Jue

Bond length and bond angle exhibited by valence electrons is essential to the core of chemistry. Using lead-based organic–inorganic perovskite compounds as an exploratory platform, it is demonstrated that the modulation of valence electrons by compression can lead to discovery of new properties of known compounds. Yet, despite its unprecedented progress, further efficiency boost of lead-based organic–inorganic perovskite solar cells is hampered by their wider bandgap than the optimum value according to the Shockley–Queisser limit. By modulating the valence electron wavefunction with modest hydraulic pressure up to 2.1 GPa, the optimized bandgap for single-junction solar cells in lead-based perovskites, formore » the first time, is achieved by narrowing the bandgap of formamidinium lead triiodide (HC(NH 2) 2PbI 3) from 1.489 to 1.337 eV. Strikingly, such bandgap narrowing is partially retained after the release of pressure to ambient, and the bandgap narrowing is also accompanied with double-prolonged carrier lifetime. With First-principles simulation, this work opens a new dimension in basic chemical understanding of structural photonics and electronics and paves an alternative pathway toward better photovoltaic materials-by-design.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Gang; Kong, Lingping; Gong, Jue

Bond length and bond angle exhibited by valence electrons is essential to the core of chemistry. Using lead-based organic–inorganic perovskite compounds as an exploratory platform, it is demonstrated that the modulation of valence electrons by compression can lead to discovery of new properties of known compounds. Yet, despite its unprecedented progress, further efficiency boost of lead-based organic–inorganic perovskite solar cells is hampered by their wider bandgap than the optimum value according to the Shockley–Queisser limit. By modulating the valence electron wavefunction with modest hydraulic pressure up to 2.1 GPa, the optimized bandgap for single-junction solar cells in lead-based perovskites, formore » the first time, is achieved by narrowing the bandgap of formamidinium lead triiodide (HC(NH2)2PbI3) from 1.489 to 1.337 eV. Strikingly, such bandgap narrowing is partially retained after the release of pressure to ambient, and the bandgap narrowing is also accompanied with double-prolonged carrier lifetime. With First-principles simulation, this work opens a new dimension in basic chemical understanding of structural photonics and electronics and paves an alternative pathway toward better photovoltaic materials-by-design.« less

Stabilized wide bandgap MAPbBr xI 3-x perovskite by enhanced grain size and improved crystallinity

DOE PAGES

Hu, Miao; Bi, Cheng; Yuan, Yongbo; ...

2015-12-07

In this study, the light instability of CH 3NH 3PbI xBr 3–x has been raised one of the biggest challenges for its application in tandem solar cells. Here we show that an improved crystallinity and grain size of CH 3NH 3PbI xBr 3–x films could stabilize these materials under one sun illumination, improving both the efficiency and stability of the wide-bandgap perovskite solar cells.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Soichi Noguchi arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Soichi Noguchi arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Stephen Robinson arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Stephen Robinson arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Charles Camarda arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment,to the Space Station, and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Charles Camarda arrives at KSC aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment,to the Space Station, and the external stowage platform.

Performance-based Incentives to Improve Health Status of Mothers and Newborns: What Does the Evidence Show?

PubMed Central

Agarwal, Koki; Askew, Ian; Iriarte, Emma; Morgan, Lindsay; Watson, Julia

2013-01-01

Performance-based incentives (PBIs) aim to counteract weak providers’ performance in health systems of many developing countries by providing rewards that are directly linked to better health outcomes for mothers and their newborns. Translating funding into better health requires many actions by a large number of people. The actions span from community to the national level. While different forms of PBIs are being implemented in a number of countries to improve health outcomes, there has not been a systematic review of the evidence of their impact on the health of mothers and newborns. This paper analyzes and synthesizes the available evidence from published studies on the impact of supply-side PBIs on the quantity and quality of health services for mothers and newborns. This paper reviews evidence from published and grey literature that spans PBI for public-sector facilities, PBI in social insurance reforms, and PBI in NGO contracting. Some initiatives focus on safe deliveries, and others reward a broader package of results that include deliveries. The Evidence Review Team that focused on supply-side incentives for the US Government Evidence Summit on Enhancing Provision and Use of Maternal Health Services through Financial Incentives, reviewed published research reports and papers and added studies from additional grey literature that were deemed relevant. After collecting and reviewing 17 documents, nine studies were included in this review, three of which used before-after designs; four included comparison or control groups; one applied econometric methods to a five-year time series; and one reported results from a large-scale impact evaluation with randomly-assigned intervention and control facilities. The available evidence suggests that incentives that reward providers for institutional deliveries result in an increase in the number of institutional deliveries. There is some evidence that the content of antenatal care can improve with PBI. We found no direct evidence on the impact of PBI on neonatal health services or on mortality of mothers and newborns, although intention of the study was not to document impact on mortality. A number of studies describe approaches to rewarding quality as well as increases in the quantities of services provided, although how quality is defined and monitored is not always clear. Because incentives exist in all health systems, considering how to align the incentives of the many health workers and their supervisors so that they focus efforts on achieving health goals for mothers and newborns is critical if the health system is to perform more effectively and efficiently. A wide range of PBI models is being developed and tested, and there is still much to learn about what works best. Future studies should include a larger focus on rewarding quality and measuring its impact. Finally, more qualitative research to better understand PBI implementation and how various incentive models function in different settings is needed to help practitioners refine and improve their programmes.

Performance-based incentives to improve health status of mothers and newborns: what does the evidence show?

PubMed

Eichler, Rena; Agarwal, Koki; Askew, Ian; Iriarte, Emma; Morgan, Lindsay; Watson, Julia

2013-12-01

Performance-based incentives (PBIs) aim to counteract weak providers' performance in health systems of many developing countries by providing rewards that are directly linked to better health outcomes for mothers and their newborns. Translating funding into better health requires many actions by a large number of people. The actions span from community to the national level. While different forms of PBIs are being implemented in a number of countries to improve health outcomes, there has not been a systematic review of the evidence of their impact on the health of mothers and newborns. This paper analyzes and synthesizes the available evidence from published studies on the impact of supply-side PBIs on the quantity and quality of health services for mothers and newborns. This paper reviews evidence from published and grey literature that spans PBI for public-sector facilities, PBI in social insurance reforms, and PBI in NGO contracting. Some initiatives focus on safe deliveries, and others reward a broader package of results that include deliveries. The Evidence Review Team that focused on supply-side incentives for the US Government Evidence Summit on Enhancing Provision and Use of Maternal Health Services through Financial Incentives, reviewed published research reports and papers and added studies from additional grey literature that were deemed relevant. After collecting and reviewing 17 documents, nine studies were included in this review, three of which used before-after designs; four included comparison or control groups; one applied econometric methods to a five-year time series; and one reported results from a large-scale impact evaluation with randomly-assigned intervention and control facilities. The available evidence suggests that incentives that reward providers for institutional deliveries result in an increase in the number of institutional deliveries. There is some evidence that the content of antenatal care can improve with PBI. We found no direct evidence on the impact of PBI on neonatal health services or on mortality of mothers and newborns, although intention of the study was not to document impact on mortality. A number of studies describe approaches to rewarding quality as well as increases in the quantities of services provided, although how quality is defined and monitored is not always clear. Because incentives exist in all health systems, considering how to align the incentives of the many health workers and their supervisors so that they focus efforts on achieving health goals for mothers and newborns is critical if the health system is to perform more effectively and efficiently. A wide range of PBI models is being developed and tested, and there is still much to learn about what works best. Future studies should include a larger focus on rewarding quality and measuring its impact. Finally, more qualitative research to better understand PBI implementation and how various incentive models function in different settings is needed to help practitioners refine and improve their programmes.

Officials welcome the arrival of the Japanese Experiment Module

NASA Image and Video Library

2007-04-17

In the Space Station Processing Facility, astronaut Takao Doi (left) and Commander Dominic Gorie pose in front of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module, or JEM, that recently arrived at Kennedy. Doi and Gorie are crew members for mission STS-123 that will deliver the logistics module to the International Space Station. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the module. The new International Space Station component arrived at Kennedy March 12 to begin preparations for its future launch on mission STS-123. It will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module.

Hypofractionated whole breast radiation and partial breast radiation for early-stage breast cancers: an update on progress.

PubMed

McCormick, Beryl

2012-09-01

This article provides an update of recent progress using partial breast irradiation (PBI) for the treatment of early-stage breast cancer, rather than whole breast radiotherapy (WBRT), which is the standard of care. Several large, prospective, randomized trials are nearing target accrual or have been completed, including the NSABP/RTOG trial, the Milan-based intraoperative radiation trial, and the international TARGIT trial, and the status of each is discussed. The American Society for Radiation Oncology has also published a consensus statement to guide the use of PBI until some of the phase III trials are more mature. Finally, several articles have appeared recently, reporting unexpected adverse effects of PBI in small series, and this information is reviewed. Several recent prospective trials of WBRT are also discussed, with the theme of comparing the standard 25 fractions to a shortened, hypofractionated trial arm delivering equivalent doses of WBRT in approximately 15 treatments, another radiation strategy for a shortened course of treatment after breast-conserving surgery.

Simulation study on improving efficiencies of perovskite solar cell: Introducing nano textures on it

NASA Astrophysics Data System (ADS)

Xie, Ziang; Sun, Shuren; Wang, Wei; Qin, Laixiang; Yan, Yu; Hou, Ruixiang; Qin, G. G.

2018-03-01

We report that the power conversion efficiencies (PCEs) of the planar CH3NH3PbI3 solar cells (SCs) can be largely improved by fabricating nano textures on the SC surface. With the finite difference time domain (FDTD) method, the ultimate efficiencies of the planar CH3NH3PbI3 SCs with two types of nano textures are investigated: the column-shaped nano hollow (CLNH) array and the cone-shaped nano hollow (CNNH) array. For the nano textured CH3NH3PbI3 SCs with photovoltaic layer depth in the range of 125 nm ∼ 500 nm, when the array period and filling fraction of the nano textures are optimized, in comparison with the planar ones, their PCE increased 42% ∼ 84% for the CLNH textured ones, and 52% ∼ 63% for the CNNH textured ones. As a conclusion, introduction of nano textures on the SC surface is a promising route for improving the PCEs of the perovskite SCs.

Efficient non-doped phosphorescent orange, blue and white organic light-emitting devices.

PubMed

Yin, Yongming; Yu, Jing; Cao, Hongtao; Zhang, Letian; Sun, Haizhu; Xie, Wenfa

2014-10-24

Efficient phosphorescent orange, blue and white organic light-emitting devices (OLEDs) with non-doped emissive layers were successfully fabricated. Conventional blue phosphorescent emitters bis [4,6-di-fluorophenyl]-pyridinato-N,C(2')] picolinate (Firpic) and Bis(2,4-difluorophenylpyridinato) (Fir6) were adopted to fabricate non-doped blue OLEDs, which exhibited maximum current efficiency of 7.6 and 4.6 cd/A for Firpic and Fir6 based devices, respectively. Non-doped orange OLED was fabricated utilizing the newly reported phosphorescent material iridium (III) (pbi)₂Ir(biq), of which manifested maximum current and power efficiency of 8.2 cd/A and 7.8 lm/W. The non-doped white OLEDs were achieved by simply combining Firpic or Fir6 with a 2-nm (pbi)₂Ir(biq). The maximum current and power efficiency of the Firpic and (pbi)₂Ir(biq) based white OLED were 14.8 cd/A and 17.9 lm/W.

Surface Plasmon Resonance Effect in Inverted Perovskite Solar Cells.

PubMed

Cui, Jin; Chen, Cheng; Han, Junbo; Cao, Kun; Zhang, Wenjun; Shen, Yan; Wang, Mingkui

2016-03-01

This work reports on incorporation of spectrally tuned gold/silica (Au/SiO 2 ) core/shell nanospheres and nanorods into the inverted perovskite solar cells (PVSC). The band gap of hybrid lead halide iodide (CH 3 NH 3 PbI 3 ) can be gradually increased by replacing iodide with increasing amounts of bromide, which can not only offer an appreciate solar radiation window for the surface plasmon resonance effect utilization, but also potentially result in a large open circuit voltage. The introduction of localized surface plasmons in CH 3 NH 3 PbI 2.85 Br 0.15 -based photovoltaic system, which occur in response to electromagnetic radiation, has shown dramatic enhancement of exciton dissociation. The synchronized improvement in photovoltage and photocurrent leads to an inverted CH 3 NH 3 PbI 2.85 Br 0.15 planar PVSC device with power conversion efficiency of 13.7%. The spectral response characterization, time resolved photoluminescence, and transient photovoltage decay measurements highlight the efficient and simple method for perovskite devices.

Metal Halide Solid-State Surface Treatment for High Efficiency PbS and PbSe QD Solar Cells

PubMed Central

Crisp, Ryan W.; Kroupa, Daniel M.; Marshall, Ashley R.; Miller, Elisa M.; Zhang, Jianbing; Beard, Matthew C.; Luther, Joseph M.

2015-01-01

We developed a layer-by-layer method of preparing PbE (E = S or Se) quantum dot (QD) solar cells using metal halide (PbI2, PbCl2, CdI2, or CdCl2) salts dissolved in dimethylformamide to displace oleate surface ligands and form conductive QD solids. The resulting QD solids have a significant reduction in the carbon content compared to films treated with thiols and organic halides. We find that the PbI2 treatment is the most successful in removing alkyl surface ligands and also replaces most surface bound Cl- with I-. The treatment protocol results in PbS QD films exhibiting a deeper work function and band positions than other ligand exchanges reported previously. The method developed here produces solar cells that perform well even at film thicknesses approaching a micron, indicating improved carrier transport in the QD films. We demonstrate QD solar cells based on PbI2 with power conversion efficiencies above 7%. PMID:25910183

Parental representations in drug-dependent patients and their parents.

PubMed

Torresani, S; Favaretto, E; Zimmermann, C

2000-01-01

The Parental Bonding Instrument (PBI), a measure of perceived parental care and protection, was administered to drug-dependent patients and their parents with the aim to assess the reliability of the instrument in such samples and to compare the parental representations across generations. Ninety drug-dependent patients and 44 mothers and 35 fathers participated. Reliability indices were calculated, and parental representations of parents and their offspring were compared. Linear regression analyses were performed with the patient's PBI score as the dependent variable and the mother's and father's PBI scores as predictor variables. The reliability indices were highly satisfactory and varied between 0.61 and 0.91. The parental bonding of patients, fathers, and mothers was similar. All three groups reported high maternal and paternal control and low maternal care, a pattern characteristic of an "affectionless control" rearing style. Maternal care received by the fathers and paternal protection received by the mothers predicted the care and protection they themselves gave to their drug-dependent offspring.

Metal halide solid-state surface treatment for high efficiency PbS and PbSe QD solar cells.

PubMed

Crisp, Ryan W; Kroupa, Daniel M; Marshall, Ashley R; Miller, Elisa M; Zhang, Jianbing; Beard, Matthew C; Luther, Joseph M

2015-04-24

We developed a layer-by-layer method of preparing PbE (E = S or Se) quantum dot (QD) solar cells using metal halide (PbI2, PbCl2, CdI2, or CdCl2) salts dissolved in dimethylformamide to displace oleate surface ligands and form conductive QD solids. The resulting QD solids have a significant reduction in the carbon content compared to films treated with thiols and organic halides. We find that the PbI2 treatment is the most successful in removing alkyl surface ligands and also replaces most surface bound Cl(-) with I(-). The treatment protocol results in PbS QD films exhibiting a deeper work function and band positions than other ligand exchanges reported previously. The method developed here produces solar cells that perform well even at film thicknesses approaching a micron, indicating improved carrier transport in the QD films. We demonstrate QD solar cells based on PbI2 with power conversion efficiencies above 7%.

Metal Halide Solid-State Surface Treatment for High Efficiency PbS and PbSe QD Solar Cells

DOE PAGES

Crisp, R. W.; Kroupa, D. M.; Marshall, A. R.; ...

2015-04-24

We developed a layer-by-layer method of preparing PbE (E = S or Se) quantum dot (QD) solar cells using metal halide (PbI 2, PbCl 2, CdI 2, or CdCl 2) salts dissolved in dimethylformamide to displace oleate surface ligands and form conductive QD solids. The resulting QD solids have a significant reduction in the carbon content compared to films treated with thiols and organic halides. We find that the PbI 2 treatment is the most successful in removing alkyl surface ligands and also replaces most surface bound Cl- with I-. The treatment protocol results in PbS QD films exhibiting amore » deeper work function and band positions than other ligand exchanges reported previously. The method developed here produces solar cells that perform well even at film thicknesses approaching a micron, indicating improved carrier transport in the QD films. We demonstrate QD solar cells based on PbI 2 with power conversion efficiencies above 7%.« less

Room temperature solution processed low dimensional CH3NH3PbI3 NIR detector

NASA Astrophysics Data System (ADS)

Besra, N.; Paul, T.; Sarkar, P. K.; Thakur, S.; Sarkar, S.; Das, A.; Chanda, K.; Sardar, K.; Chattopadhyay, K. K.

2018-05-01

Metal halide perovskites have recently drawn immense research interests among the worldwide scientific community due to their excellent light harvesting capabilities and above all, cost effectiveness. These new class of materials have already been used as efficient optoelectronic devices e.g. solar cells, photo detectors, etc. Here in this work, room temperature NIR (near infra red) response of organic-inorganic lead halide perovskite CH3NH3PbI3 (Methylammonium lead tri iodide) nanorods has been studied. A very simple solution process technique has been adopted to synthesize CH3NH3PbI3 nanostructures at room temperature. The NIR exposure upon the sample resulted in a considerable hike in its dark current with very good responsivity (0.37 mA/W). Along with that, a good on-off ratio (41.8) was also obtained when the sample was treated under a pulsed NIR exposure with operating voltage of 2 V. The specific detectivity of the device came in the order of 1010 Jone.

A rack is installed in MPLM Leonardo

NASA Technical Reports Server (NTRS)

2000-01-01

Workers inside the Multi-Purpose Logistics Module Leonardo check installation of a laboratory rack inside the Multi-Purpose Logistics Module Leonardo. The pressurized module is the first of three that will serve as the International Space Station's '''moving vans,''' carrying laboratory racks filled with equipment, experiments and supplies to and from the Space Station aboard the Space Shuttle. Approximately 21 feet long and 15 feet in diameter, Leonardo will be launched on Shuttle mission STS-102 March 1, 2001. On that flight, Leonardo will be filled with equipment and supplies to outfit the U.S. laboratory module, being carried to the ISS on the Jan. 19, 2001, launch of STS-98.

Acetate Salts as Nonhalogen Additives To Improve Perovskite Film Morphology for High-Efficiency Solar Cells.

PubMed

Wu, Qiliang; Zhou, Pengcheng; Zhou, Weiran; Wei, Xiangfeng; Chen, Tao; Yang, Shangfeng

2016-06-22

A two-step method has been popularly adopted to fabricate a perovskite film of planar heterojunction organo-lead halide perovskite solar cells (PSCs). However, this method often generates uncontrollable film morphology with poor coverage. Herein, we report a facile method to improve perovskite film morphology by incorporating a small amount of acetate (CH3COO(-), Ac(-)) salts (NH4Ac, NaAc) as nonhalogen additives in CH3NH3I solution used for immersing PbI2 film, resulting in improved CH3NH3PbI3 film morphology. Under the optimized NH4Ac additive concentration of 10 wt %, the best power conversion efficiency (PCE) reaches 17.02%, which is enhanced by ∼23.2% relative to that of the pristine device without additive, whereas the NaAc additive does not lead to an efficiency enhancement despite the improvement of the CH3NH3PbI3 film morphology. SEM study reveals that NH4Ac and NaAc additives can both effectively improve perovskite film morphology by increasing the surface coverage via diminishing pinholes. The improvement on CH3NH3PbI3 film morphology is beneficial for increasing the optical absorption of perovskite film and improving the interfacial contact at the perovskite/spiro-OMeTAD interface, leading to the increase of short-circuit current and consequently efficiency enhancement of the PSC device for NH4Ac additive only.

Effects on motor development of kicking and stepping exercise in preterm infants with periventricular brain injury: a pilot study.

PubMed

Campbell, Suzann K; Gaebler-Spira, Deborah; Zawacki, Laura; Clark, April; Boynewicz, Kara; deRegnier, Raye-Ann; Kuroda, Maxine M; Bhat, Rama; Yu, Jinsheng; Campise-Luther, Rose; Kale, Dipti; Bulanda, Michelle; Zhou, Xiaohong Joe

2012-01-01

Preterm infants with periventricular brain injury (PBI) have a high incidence of atypical development and leg movements. Determine whether kicking and treadmill stepping intervention beginning at 2 months corrected age (CA) in children with PBI improves motor function at 12 months CA when compared with control subjects. In a multi-center pilot study for a controlled clinical trial, sixteen infants with PBI were randomly assigned to home exercise consisting of kicking and treadmill stepping or a no-training control condition. Development was assessed at 2, 4, 6, 10, and 12 months CA with the Alberta Infant Motor Scale (AIMS). At 12 months children were classified as normal, delayed, or with cerebral palsy (CP). At 12 months CA 3 of 7 (43%) of the exercise group children walked alone or with one hand held versus 1 of 9 (11%) in the control group (p=0.262), but no significant differences in AIMS scores were found at any age. Half of the subjects had CP or delay; the outcomes of these infants were not improved by exercise. Compliance with the home program was lower than requested and may have affected results. Although not statistically significant with a small sample size, self-produced kicking and treadmill exercise may lower age at walking in infants with normal development following PBI, but improvements of the protocol to increase and document compliance are needed before a larger study is implemented.

Effects on Motor Development of Kicking and Stepping Exercise in Preterm Infants with Periventricular Brain Injury: A Pilot Study

PubMed Central

Campbell, Suzann K.; Gaebler-Spira, Deborah; Zawacki, Laura; Clark, April; Boynewicz, Kara; deRegnier, Raye-Ann; Kuroda, Maxine M.; Bhat, Rama; Yu, Jinsheng; Campise-Luther, Rose; Kale, Dipti; Bulanda, Michelle; Zhou, Xiaohong Joe

2013-01-01

Background Preterm infants with periventricular brain injury (PBI) have a high incidence of atypical development and leg movements. Objective Determine whether kicking and treadmill stepping intervention beginning at 2 months corrected age (CA) in children with PBI improves motor function at 12 months CA when compared with control subjects. Method In a multi-center pilot study for a controlled clinical trial, sixteen infants with PBI were randomly assigned to home exercise consisting of kicking and treadmill stepping or a no-training control condition. Development was assessed at 2, 4, 6, 10, and 12 months CA with the Alberta Infant Motor Scale (AIMS). At 12 months children were classified as normal, delayed, or with cerebral palsy (CP). Results At 12 months CA 3 of 7 (43%) of the exercise group children walked alone or with one hand held versus 1 of 9 (11%) in the control group (p=.262), but no significant differences in AIMS scores were found at any age. Half of the subjects had CP or delay; the outcomes of these infants were not improved by exercise. Compliance with the home program was lower than requested and may have affected results. Conclusion Although not statistically significant with a small sample size, self-produced kicking and treadmill exercise may lower age at walking in infants with normal development following PBI, but improvements of the protocol to increase and document compliance are needed before a larger study is implemented. PMID:22543889

Empirical evidence for an invariant three-factor structure of the Parental Bonding Instrument in six European countries.

PubMed

Heider, Dirk; Matschinger, Herbert; Bernert, Sebastian; Vilagut, Gemma; Martínez-Alonso, Montserrat; Dietrich, Sandra; Angermeyer, Matthias C

2005-06-30

The objective of the present study was to test the Parental Bonding Instrument's (PBI) three-factor structure (care, overprotection, and authoritarianism) found by [Cox, B.J., Enns, M.W., Clara, I.P. 2000, The Parental Bonding Instrument: confirmatory evidence for a three-factor model in a psychiatric clinical sample and in the National Comorbidity Survey, Social Psychiatry and Psychiatric Epidemiology 35 (2000) 353-357.] on an eight-item short form of the scale. A total of 8813 respondents from the six European countries participating in the ESEMeD project (Belgium, France, Germany, Italy, The Netherlands, and Spain) completed either the PBI-paternal or the PBI-maternal scale. Maximum likelihood confirmatory factor analysis was used to compare the original factor model of Cox et al. with a three-factor solution that emerged from an exploration of the structure with principal component factor analysis. When gender and age subgroups, as well as different countries, were taken into account, the accuracy of the model was confirmed. The fit indices for the new model indicated a generally better model fit than the ones for the model originally developed by Cox et al. Further efforts should be directed to the modeling of the dimension authoritarianism. The results provide the opportunity to estimate the influence of the extracted factors on mental disorders in different countries. The application of the short form of the PBI seems suitable primarily for large epidemiological studies.

Sensing of Double-Stranded DNA/RNA Secondary Structures by Water Soluble Homochiral Perylene Bisimide Dyes.

PubMed

Gershberg, Jana; Radić Stojković, Marijana; Škugor, Marko; Tomić, Sanja; Rehm, Thomas H; Rehm, Stefanie; Saha-Möller, Chantu R; Piantanida, Ivo; Würthner, Frank

2015-05-18

A broad series of homochiral perylene bisimide (PBI) dyes were synthesized that are appended with amino acids and cationic side chains at the imide positions. Self-assembly behavior of these ionic PBIs has been studied in aqueous media by UV/Vis spectroscopy, revealing formation of excitonically coupled H-type aggregates. The interactions of these ionic PBIs with different ds-DNA and ds-RNA have been explored by thermal denaturation, fluorimetric titration and circular dichroism (CD) experiments. These PBIs strongly stabilized ds-DNA/RNA against thermal denaturation as revealed by high melting temperatures of the formed PBI/polynucleotide complexes. Fluorimetric titrations showed that these PBIs bind to ds-DNA/RNA with high binding constants depending on the number of the positive charges in the side chains. Thus, spermine-containing PBIs with six positive charges each showed higher binding constants (logKs =9.2-9.8) than their dioxa analogues (logKs =6.5-7.9) having two positive charges each. Induced circular dichroism (ICD) of PBI assemblies created within DNA/RNA grooves was observed. These ICD profiles are strongly dependent on the steric demand of the chiral substituents of the amino acid units and the secondary structure of the DNA or RNA. The observed ICD effects can be explained by non-covalent binding of excitonically coupled PBI dimer aggregates into the minor groove of DNA and major groove of RNA which is further supported by molecular modeling studies. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Recombination reduction on lead halide perovskite solar cells based on low temperature synthesized hierarchical TiO₂ nanorods.

PubMed

Jaramillo-Quintero, Oscar A; Solís de la Fuente, Mauricio; Sanchez, Rafael S; Recalde, Ileana B; Juarez-Perez, Emilio J; Rincón, Marina E; Mora-Seró, Iván

2016-03-28

Intensive research on the electron transport material (ETM) has been pursued to improve the efficiency of perovskite solar cells (PSCs) and decrease their cost. More importantly, the role of the ETM layer is not yet fully understood, and research on new device architectures is still needed. Here, we report the use of three-dimensional (3D) TiO2 with a hierarchical architecture based on rutile nanorods (NR) as photoanode material for PSCs. The proposed hierarchical nanorod (HNR) films were synthesized by a two-step low temperature (180 °C) hydrothermal method, and consist of TiO2 nanorod trunks with optimal lengths of 540 nm and TiO2 nanobranches with lengths of 45 nm. Different device configurations were fabricated with TiO2 structures (compact layer, NR and HNR) and CH3NH3PbI3, using different synthetic routes, as the active material. PSCs based on HNR-CH3NH3PbI3 achieved the highest power conversion efficiency compared to PSCs with other TiO2 structures. This result can be ascribed mainly to lower charge recombination as determined by impedance spectroscopy. Furthermore, we have observed that the CH3NH3PbI3 perovskite deposited by the two-step route shows higher efficiency, surface coverage and infiltration within the structure of 3D HNR than the one-step CH3NH3PbI(3-x)Cl(x) perovskite.

Interfacial electronic structures revealed at the rubrene/CH3NH3PbI3 interface.

PubMed

Ji, Gengwu; Zheng, Guanhaojie; Zhao, Bin; Song, Fei; Zhang, Xiaonan; Shen, Kongchao; Yang, Yingguo; Xiong, Yimin; Gao, Xingyu; Cao, Liang; Qi, Dong-Chen

2017-03-01

The electronic structures of rubrene films deposited on CH 3 NH 3 PbI 3 perovskite have been investigated using in situ ultraviolet photoelectron spectroscopy (UPS) and X-ray photoelectron spectroscopy (XPS). It was found that rubrene molecules interacted weakly with the perovskite substrate. Due to charge redistribution at their interface, a downward 'band bending'-like energy shift of ∼0.3 eV and an upward band bending of ∼0.1 eV were identified at the upper rubrene side and the CH 3 NH 3 PbI 3 substrate side, respectively. After the energy level alignment was established at the rubrene/CH 3 NH 3 PbI 3 interface, its highest occupied molecular orbital (HOMO)-valence band maximum (VBM) offset was found to be as low as ∼0.1 eV favoring the hole extraction with its lowest unoccupied molecular orbital (LUMO)-conduction band minimum (CBM) offset as large as ∼1.4 eV effectively blocking the undesired electron transfer from perovskite to rubrene. As a demonstration, simple inverted planar solar cell devices incorporating rubrene and rubrene/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) hole transport layers (HTLs) were fabricated in this work and yielded a champion power conversion efficiency of 8.76% and 13.52%, respectively. Thus, the present work suggests that a rubrene thin film could serve as a promising hole transport layer for efficient perovskite-based solar cells.

Direct Observation of Dynamic Symmetry Breaking above Room Temperature in Methylammonium Lead Iodide Perovskite

DOE PAGES

Beecher, Alexander N.; Semonin, Octavi E.; Skelton, Jonathan M.; ...

2016-09-21

Lead halide perovskites such as methylammonium lead triiodide (CH 3NH 3PbI 3) have outstanding optical and electronic properties for photovoltaic applications, yet a full understanding of how this solution-processable material works so well is currently missing. Previous research has revealed that CH 3NH 3PbI 3 possesses multiple forms of static disorder regardless of preparation method, which is surprising in light of its excellent performance. Using high energy resolution inelastic X-ray (HERIX) scattering, we measure phonon dispersions in CH 3NH 3PbI 3 and find direct evidence for another form of disorder in single crystals: large-amplitude anharmonic zone edge rotational instabilities ofmore » the PbI 6 octahedral that persist to room temperature and above, left over from structural phase transitions that take place tens to hundreds of degrees below. Phonon calculations show that the orientations of the methylammonium (CH 3NH 3 +) couple strongly and cooperatively to these modes. The result is a noncentrosymmetric, instantaneous local structure, which we observe in atomic pair distribution function (PDF) measurements. This local symmetry breaking is unobservable by Bragg diffraction but can explain key material properties such as the structural phase sequence, ultralow thermal transport, and large minority charge carrier lifetimes despite moderate carrier mobility. In conclusion, from the PDF we estimate the size of the fluctuating symmetry broken domains to be between 1 and 3 nm in diameter.« less

Effect of halide-mixing on the switching behaviors of organic-inorganic hybrid perovskite memory

NASA Astrophysics Data System (ADS)

Hwang, Bohee; Gu, Chungwan; Lee, Donghwa; Lee, Jang-Sik

2017-03-01

Mixed halide perovskite materials are actively researched for solar cells with high efficiency. Their hysteresis which originates from the movement of defects make perovskite a candidate for resistive switching memory devices. We demonstrate the resistive switching device based on mixed-halide organic-inorganic hybrid perovskite CH3NH3PbI3-xBrx (x = 0, 1, 2, 3). Solvent engineering is used to deposit the homogeneous CH3NH3PbI3-xBrx layer on the indium-tin oxide-coated glass substrates. The memory device based on CH3NH3PbI3-xBrx exhibits write endurance and long retention, which indicate reproducible and reliable memory properties. According to the increase in Br contents in CH3NH3PbI3-xBrx the set electric field required to make the device from low resistance state to high resistance state decreases. This result is in accord with the theoretical calculation of migration barriers, that is the barrier to ionic migration in perovskites is found to be lower for Br- (0.23 eV) than for I- (0.29-0.30 eV). The resistive switching may be the result of halide vacancy defects and formation of conductive filaments under electric field in the mixed perovskite layer. It is observed that enhancement in operating voltage can be achieved by controlling the halide contents in the film.

Optical Sensing of Aromatic Amino Acids and Dipeptides by a Crown-Ether-Functionalized Perylene Bisimide Fluorophore.

PubMed

Weißenstein, Annike; Saha-Möller, Chantu R; Würthner, Frank

2018-06-04

The host-guest binding properties of a fluorescent perylene bisimide (PBI) receptor equipped with crown ether were studied in detail with a series of aromatic amino acids and dipeptides by UV/Vis, fluorescence and NMR spectroscopy. Fluorescence titration experiments showed that electron-rich aromatic amino acids and dipeptides strongly quench the fluorescence of the electron-poor PBI host molecule. Benesi-Hildebrand plots of fluorescence titration data confirmed the formation of host-guest complexes with 1:2 stoichiometry. Binding constants determined by global analysis of UV/Vis and fluorescence titration experiments revealed values between 10 3  m -1 and 10 5  m -1 in acetonitrile/methanol (9:1) at 23 °C. These data showed that amino acid l-Trp having an indole group and dipeptides containing this amino acid bind to the PBI receptor more strongly than other amino acids and dipeptides investigated here. For dipeptides containing l-Trp or l-Tyr, the binding strength is dependent on the distance between the ammonium group and the aromatic unit of the amino acids and dipeptides leading to a strong sensitivity for Ala-Trp dipeptide. 1D and 2D NMR experiments also corroborated 1:2 host-guest complexation and indicated formation of two diastereomeric species of host-guest complexes. The studies have shown that a properly functionalized PBI fluorophore functions as a molecular probe for the optical sensing of aromatic amino acids and dipeptides. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Decorating unoxidized-carbon nanotubes with homogeneous Ni-Co spinel nanocrystals show superior performance for oxygen evolution/reduction reactions

NASA Astrophysics Data System (ADS)

Yang, Jun; Fujigaya, Tsuyohiko; Nakashima, Naotoshi

2017-03-01

We present a new concept for homogeneous spinel nanocrystal-coating on high crystalline pristine-carbon nanotubes (CNTs) for efficient and durable oxygen evolution reaction (OER) and oxygen reduction reaction (ORR). Oxidized CNTs have widely been used to functionalize with metal or metal oxides since the defect sites act as anchoring for metal oxide binding. However, such defects on the tubes cause the decrease in electrical conductivity and stability, leading to lower catalyst performance. In the present study, at first, pristine multi-walled carbon nanotubes (MWNTs) were wrapped by pyridine-based polybenzimidazole (PyPBI) to which uniform NixCo3-xO4 nanocrystals were homogeneously deposited by the solvothermal method without damaging the MWNTs, in which PyPBI acted as efficient anchoring sites for the deposition of spinel oxide nanocrystals with ~5 nm size. The obtained catalyst (MWNT-PyPBI-NixCo3-xO4) outperformed most state-of-the-art non-precious metal-based bifunctional catalysts; namely, for OER, the potential at 10 mA cm-2 and Tafel slope in 1 M KOH solution were 1.54 V vs. RHE and 42 mV dec-1, respectively. For ORR, the onset and half-wave potentials are 0.918 V and 0.811 V vs. RHE, respectively. Moreover, the MWNT-PyPBI-NixCo3-xO4 demonstrates an excellent durability for both ORR and OER.

STS-102 Onboard Photograph Inside Multipurpose Logistics Module, Leonardo

NASA Technical Reports Server (NTRS)

2001-01-01

Pilot James M. Kelly (left) and Commander James D. Wetherbee for the STS-102 mission, participate in the movement of supplies inside Leonardo, the Italian Space Agency built Multipurpose Logistics Module (MPLM). In this particular photograph, the two are handling a film magazine for the IMAX cargo bay camera. The primary cargo of the STS-102 mission, the Leonardo MPLM is the first of three such pressurized modules that will serve as the International Space Station's (ISS') moving vans, carrying laboratory racks filled with equipment, experiments, and supplies to and from the Station aboard the Space Shuttle. The cylindrical module is approximately 21-feet long and 15- feet in diameter, weighing almost 4.5 tons. It can carry up to 10 tons of cargo in 16 standard Space Station equipment racks. Of the 16 racks the module can carry, 5 can be furnished with power, data, and fluid to support refrigerators or freezers. In order to function as an attached station module as well as a cargo transport, the logistics module also includes components that provide life support, fire detection and suppression, electrical distribution, and computer functions. The eighth station assembly flight, the STS-102 mission also served as a crew rotation flight. It delivered the Expedition Two crew to the Station and returned the Expedition One crew back to Earth.

Android platform based smartphones for a logistical remote association repair framework.

PubMed

Lien, Shao-Fan; Wang, Chun-Chieh; Su, Juhng-Perng; Chen, Hong-Ming; Wu, Chein-Hsing

2014-06-25

The maintenance of large-scale systems is an important issue for logistics support planning. In this paper, we developed a Logistical Remote Association Repair Framework (LRARF) to aid repairmen in keeping the system available. LRARF includes four subsystems: smart mobile phones, a Database Management System (DBMS), a Maintenance Support Center (MSC) and wireless networks. The repairman uses smart mobile phones to capture QR-codes and the images of faulty circuit boards. The captured QR-codes and images are transmitted to the DBMS so the invalid modules can be recognized via the proposed algorithm. In this paper, the Linear Projective Transform (LPT) is employed for fast QR-code calibration. Moreover, the ANFIS-based data mining system is used for module identification and searching automatically for the maintenance manual corresponding to the invalid modules. The inputs of the ANFIS-based data mining system are the QR-codes and image features; the output is the module ID. DBMS also transmits the maintenance manual back to the maintenance staff. If modules are not recognizable, the repairmen and center engineers can obtain the relevant information about the invalid modules through live video. The experimental results validate the applicability of the Android-based platform in the recognition of invalid modules. In addition, the live video can also be recorded synchronously on the MSC for later use.

KSC-07pd2843

NASA Image and Video Library

2007-10-11

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility at NASA's Kennedy Space Center, members of the STS-123 crew learn more about the mission payload, the Kibo Experiment Logistics Module Pressurized Section. Crew members are Commander Dominic Gorie, Pilot Gregory Johnson and Mission Specialists Richard Linnehan, Takao Doi, Robert Behnken, Gerrett Reisman and Michael Foreman. Doi represents the Japan Aerospace Exploration Agency. Reisman will remain on the space station after the mission as a flight engineer for Expedition 16. STS-123 will carry and install one of the components of the Japanese Experiment Module, or JEM. Known as Kibo, the JEM comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. The various components of JEM will be assembled in space over the course of three space shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the space shuttle Endeavour, targeted for launch in February 2008. Photo credit: NASA/Dimitrios Gerondidakis

In-space propellant logistics. Volume 4: Project planning data

NASA Technical Reports Server (NTRS)

1972-01-01

The prephase A conceptual project planning data as it pertains to the development of the selected logistics module configuration transported into earth orbit by the space shuttle orbiter. The data represents the test, implementation, and supporting research and technology requirements for attaining the propellant transfer operational capability for early 1985. The plan is based on a propellant module designed to support the space-based tug with cryogenic oxygen-hydrogen propellants. A logical sequence of activities that is required to define, design, develop, fabricate, test, launch, and flight test the propellant logistics module is described. Included are the facility and ground support equipment requirements. The schedule of activities are based on the evolution and relationship between the R and T, the development issues, and the resultant test program.

The Raffaello, a Multi-Purpose Logistics Module, arrives at KSC aboard a Beluga super transporter

NASA Technical Reports Server (NTRS)

1999-01-01

An Airbus Industrie A300-600ST 'Beluga' Super Transporter is reflected in the rain puddles as it comes to a stop at the Shuttle Landing Facility. The Beluga is carrying the Raffaello, the second Multi-Purpose Logistics Module (MPLM) for the International Space Station (ISS). One of Italy's major contributions to the ISS program, the MPLM is a reusable logistics carrier and the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Weighing nearly 4.5 tons, the module measures 21 feet long and 15 feet in diameter. Raffaello will join Leonardo, the first Italian-built MPLM, in the Space Station Processing Facility for testing. NASA, Boeing, the Italian Space Agency and Alenia Aerospazio will provide engineering support.

The Raffaello, a Multi-Purpose Logistics Module, arrives at KSC aboard a Beluga super transporter

NASA Technical Reports Server (NTRS)

1999-01-01

An Airbus Industrie A300-600ST 'Beluga' Super Transporter is reflected in the rain puddles as it taxis toward the mate/demate tower at the Shuttle Landing Facility. The Beluga is carrying the Raffaello, the second Multi-Purpose Logistics Module (MPLM) for the International Space Station (ISS). One of Italy's major contributions to the ISS program, the MPLM is a reusable logistics carrier and the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Weighing nearly 4.5 tons, the module measures 21 feet long and 15 feet in diameter. Raffaello will join Leonardo, the first Italian-built MPLM, in the Space Station Processing Facility for testing. NASA, Boeing, the Italian Space Agency and Alenia Aerospazio will provide engineering support.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Soichi Noguchi is happy to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Soichi Noguchi is happy to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Commander Eileen Collins is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. She and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver to the Space Station the external stowage platform and the Multi-Purpose Logistics Module with supplies and equipment.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Commander Eileen Collins is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. She and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver to the Space Station the external stowage platform and the Multi-Purpose Logistics Module with supplies and equipment.

KENNEDY SPACE CENTER, FLA. - STS-114 Pilot Jim Kelly is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Pilot Jim Kelly is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Andrew Thomas is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver to the Space Station the external stowage platform and the Multi-Purpose Logistics Module with supplies and equipment.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Andrew Thomas is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. He and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver to the Space Station the external stowage platform and the Multi-Purpose Logistics Module with supplies and equipment.

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Wendy Lawrence is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. She and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

NASA Image and Video Library

2004-03-05

KENNEDY SPACE CENTER, FLA. - STS-114 Mission Specialist Wendy Lawrence is pleased to be back at KSC after arriving aboard a T-38 jet aircraft. She and other crew members are at the Center for familiarization activities with equipment. The mission is Logistics Flight 1, scheduled to deliver the Multi-Purpose Logistics Module carrying supplies and equipment to the Space Station and the external stowage platform.

Enhancement of the Logistics Battle Command Model: Architecture Upgrades and Attrition Module Development

DTIC Science & Technology

2017-01-05

module. 15. SUBJECT TERMS Logistics, attrition, discrete event simulation, Simkit, LBC 16. SECURITY CLASSIFICATION OF: Unclassified 17. LIMITATION...stochastics, and discrete event model programmed in Java building largely on the Simkit library. The primary purpose of the LBC model is to support...equations makes them incompatible with the discrete event construct of LBC. Bullard further advances this methodology by developing a stochastic

Logistics support of the Japanese Experiment Module by the H-II rocket

NASA Astrophysics Data System (ADS)

Shibato, Yoji; Eto, Takao; Fukushima, Yukio; Takatsuka, Hitoshi

1988-10-01

This paper describes salient design features of the Japanese Experiment Module (JEM), which will be attached to the Space Station. Special attention is given to the logistic support of the JEM (which is planned to become operational in 1990s) by the HOPE orbiter, which will be used for the resupply and the retrieval of the JEM, and the H-II rocket, which will be used to launch the HOPE. The concepts of HOPE and the H-II rocket are discussed together with the estimated logistics requirements of this system. Configuration diagrams are included.

Modular space station mass properties

NASA Technical Reports Server (NTRS)

1972-01-01

An update of the space station mass properties is presented. Included are the final status update of the Initial Space Station (ISS) modules and logistic module plus incorporation of the Growth Space Station (GSS) module additions.

High-Output-Power Densities from MBE-grown n- and p-Type PbTeSe-based Thermoelectrics via Improved Contact Metallization

DTIC Science & Technology

2011-10-19

is uncertain . . The results of these various studies seem consistent that the Fermi . level at the surface of PbTe or Pbi -xSnxTe is not inherently...Both sides: ~T=220"C n-type IS am P!!I~:Ii SE+l9 n++ 200 nm Til Device P=30W/cm2 1001!!!1 Pbi ~Se 3.5E+I8 a+ NDLS ISO am PI!I!::Bi SE+19 a++ 200nmNil

Perylene Bisimide Radicals and Biradicals: Synthesis and Molecular Properties.

PubMed

Schmidt, David; Son, Minjung; Lim, Jong Min; Lin, Mei-Jin; Krummenacher, Ivo; Braunschweig, Holger; Kim, Dongho; Würthner, Frank

2015-11-16

Unprecedented neutral perylene-3,4:9,10-tetracarboxylic acid bisimide (PBI) radicals and biradicals were synthesized by facile chemical oxidation of 4-hydroxyaryl-substituted PBIs. Subsequent characterization by optical and magnetic spectroscopic techniques, as well as quantum chemical calculations, revealed an open-shell singlet biradical ground state for the PBI biradical OS-2(..) (〈s(2)〉=1.2191) with a relatively small singlet-triplet energy gap of 0.041 eV and a large singlet biradical character of y=0.72. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Redox-Active Supramolecular Polymer Binders for Lithium–Sulfur Batteries That Adapt Their Transport Properties in Operando

DOE PAGES

Frischmann, Peter D.; Hwa, Yoon; Cairns, Elton J.; ...

2016-10-25

π-Stacked perylene bisimide (PBI) molecules are implemented here as highly networked, redox-active supramolecular polymer binders in sulfur cathodes for lightweight and energy-dense Li-S batteries. We show that the in operando reduction and lithiation of these PBI binders sustainably reduces Li-S cell impedance relative to nonredox active conventional polymer binders. This lower impedance enables high-rate cycling in Li-S cells with excellent durability, a critical step toward unlocking the full potential of Li-S batteries for electric vehicles and aviation.

Nickel oxide electrode interlayer in CH3 NH3 PbI3 perovskite/PCBM planar-heterojunction hybrid solar cells.

PubMed

Jeng, Jun-Yuan; Chen, Kuo-Cheng; Chiang, Tsung-Yu; Lin, Pei-Ying; Tsai, Tzung-Da; Chang, Yun-Chorng; Guo, Tzung-Fang; Chen, Peter; Wen, Ten-Chin; Hsu, Yao-Jane

2014-06-25

This study successfully demonstrates the application of inorganic p-type nickel oxide (NiOx ) as electrode interlayer for the fabrication of NiOx /CH3 NH3 PbI3 perovskite/PCBM PHJ hybrid solar cells with a respectable solar-to-electrical PCE of 7.8%. The better energy level alignment and improved wetting of the NiOx electrode interlayer significantly enhance the overall photovoltaic performance. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High-Performance Semitransparent Perovskite Solar Cells with 10% Power Conversion Efficiency and 25% Average Visible Transmittance Based on Transparent CuSCN as the Hole-Transporting Material

DOE PAGES

Jung, Jae Woong; Chueh, Chu-Chen; Jen, Alex K. -Y.

2015-07-06

High-performance planar heterojunction perovskite (CH3NH3PbI3) solar cell (PVSC) is demonstrated by utilizing CuSCN as a hole-transporting layer. Efficient hole-transport and hole-extraction at the CuSCN/CH3NH3PbI3 interface facilitate the PVSCs to reach 16% power conversion efficiency (PCE). In addition, excellent transparency of CuSCN enables high-performance semitransparent PVSC (10% PCE and 25% average visible transmittance) to be realized.

KSC-07pd0893

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, astronaut Takao Doi (left) and Commander Dominic Gorie pose in front of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module, or JEM, that recently arrived at Kennedy. Doi and Gorie are crew members for mission STS-123 that will deliver the logistics module to the International Space Station. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the module. The new International Space Station component arrived at Kennedy March 12 to begin preparations for its future launch on mission STS-123. It will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

KSC-07pd0894

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, astronaut Takao Doi (left) and Commander Dominic Gorie pose in front of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module, or JEM, that recently arrived at Kennedy. Doi and Gorie are crew members for mission STS-123 that will deliver the logistics module to the International Space Station. Earlier, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcomed the arrival of the module. The new International Space Station component arrived at Kennedy March 12 to begin preparations for its future launch on mission STS-123. It will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

SU-E-J-37: Feasibility of Utilizing Carbon Fiducials to Increase Localization Accuracy of Lumpectomy Cavity for Partial Breast Irradiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Y; Hieken, T; Mutter, R

2015-06-15

Purpose To investigate the feasibility of utilizing carbon fiducials to increase localization accuracy of lumpectomy cavity for partial breast irradiation (PBI). Methods Carbon fiducials were placed intraoperatively in the lumpectomy cavity following resection of breast cancer in 11 patients. The patients were scheduled to receive whole breast irradiation (WBI) with a boost or 3D-conformal PBI. WBI patients were initially setup to skin tattoos using lasers, followed by orthogonal kV on-board-imaging (OBI) matching to bone per clinical practice. Cone beam CT (CBCT) was acquired weekly for offline review. For the boost component of WBI and PBI, patients were setup with lasers,more » followed by OBI matching to fiducials, with final alignment by CBCT matching to fiducials. Using carbon fiducials as a surrogate for the lumpectomy cavity and CBCT matching to fiducials as the gold standard, setup uncertainties to lasers, OBI bone, OBI fiducials, and CBCT breast were compared. Results Minimal imaging artifacts were introduced by fiducials on the planning CT and CBCT. The fiducials were sufficiently visible on OBI for online localization. The mean magnitude and standard deviation of setup errors were 8.4mm ± 5.3 mm (n=84), 7.3mm ± 3.7mm (n=87), 2.2mm ± 1.6mm (n=40) and 4.8mm ± 2.6mm (n=87), for lasers, OBI bone, OBI fiducials and CBCT breast tissue, respectively. Significant migration occurred in one of 39 implanted fiducials in a patient with a large postoperative seroma. Conclusion OBI carbon fiducial-based setup can improve localization accuracy with minimal imaging artifacts. With increased localization accuracy, setup uncertainties can be reduced from 8mm using OBI bone matching to 3mm using OBI fiducial matching for PBI treatment. This work demonstrates the feasibility of utilizing carbon fiducials to increase localization accuracy to the lumpectomy cavity for PBI. This may be particularly attractive for localization in the setting of proton therapy and other scenarios in which metal clips are contraindicated.« less

Influence of Photobiomodulation Therapy on Gingivitis Induced by Multi-Bracket Appliances: A Split-Mouth Randomized Controlled Trial.

PubMed

Stein, Steffen; Schauseil, Michael; Hellak, Andreas; Korbmacher-Steiner, Heike; Braun, Andreas

2018-05-18

The objective of this split-mouth trial was to investigate the influence of photobiomodulation therapy (PBMT) on adjuvant treatment of gingivitis induced by multi-bracket appliances, after bracket debonding and professional tooth cleaning. Thirteen patients (mean age 16.15 years; standard deviation ±2.12 years) who had completed active orthodontic treatment with fixed orthodontic appliances in an orthodontic clinic were included on a randomized basis. At time point T0, after bracket debonding and professional tooth cleaning, the papilla bleeding index (PBI) and bleeding on probing (BOP) were assessed in the upper jaw by the blinded investigator (M.S.), who was not aware at any time of which quadrant received PBMT. The study was based on a patient-blinded split-mouth design. In each patient, PBMT was administered by a practitioner (S.S.) in one upper quadrant (wavelength: 660 nm; Power: 100 mW; Power density: 100 mW/cm 2 ; Energy density per application point = 2 J/cm 2 ; Energy per application point = 2 J; Total dose = 52 J/cm 2 ; Total energy = 52 J; Irradiation time: 26 × 20 sec), while the other upper quadrant received a simulated laser application with the laser system turned off. Randomized equal allocation of the sides was accomplished. The second PBI and BOP assessment followed 4-6 days after laser irradiation (T1) by M.S. No statistical differences were observed between the sides with regard to PBI and BOP values at T0 (p > 0.05). The PBI and BOP values decreased significantly between T0 and T1 on both sides (p < 0.05). At T1, the PBI and BOP values were significantly lower in the laser side in comparison with the control side (p < 0.05). On the basis of these results and study parameters, adjuvant PBMT is able to accelerate the healing process in patients with gingivitis induced by multi-bracket appliances.

High spatiotemporal resolution measurement of regional lung air volumes from 2D phase contrast x-ray images.

PubMed

Leong, Andrew F T; Fouras, Andreas; Islam, M Sirajul; Wallace, Megan J; Hooper, Stuart B; Kitchen, Marcus J

2013-04-01

Described herein is a new technique for measuring regional lung air volumes from two-dimensional propagation-based phase contrast x-ray (PBI) images at very high spatial and temporal resolution. Phase contrast dramatically increases lung visibility and the outlined volumetric reconstruction technique quantifies dynamic changes in respiratory function. These methods can be used for assessing pulmonary disease and injury and for optimizing mechanical ventilation techniques for preterm infants using animal models. The volumetric reconstruction combines the algorithms of temporal subtraction and single image phase retrieval (SIPR) to isolate the image of the lungs from the thoracic cage in order to measure regional lung air volumes. The SIPR algorithm was used to recover the change in projected thickness of the lungs on a pixel-by-pixel basis (pixel dimensions ≈ 16.2 μm). The technique has been validated using numerical simulation and compared results of measuring regional lung air volumes with and without the use of temporal subtraction for removing the thoracic cage. To test this approach, a series of PBI images of newborn rabbit pups mechanically ventilated at different frequencies was employed. Regional lung air volumes measured from PBI images of newborn rabbit pups showed on average an improvement of at least 20% in 16% of pixels within the lungs in comparison to that measured without the use of temporal subtraction. The majority of pixels that showed an improvement was found to be in regions occupied by bone. Applying the volumetric technique to sequences of PBI images of newborn rabbit pups, it is shown that lung aeration at birth can be highly heterogeneous. This paper presents an image segmentation technique based on temporal subtraction that has successfully been used to isolate the lungs from PBI chest images, allowing the change in lung air volume to be measured over regions as small as the pixel size. Using this technique, it is possible to measure changes in regional lung volume at high spatial and temporal resolution during breathing at much lower x-ray dose than would be required using computed tomography.

An assembly of proteins and lipid domains regulates transport of phosphatidylserine to phosphatidylserine decarboxylase 2 in Saccharomyces cerevisiae.

PubMed

Riekhof, Wayne R; Wu, Wen-I; Jones, Jennifer L; Nikrad, Mrinalini; Chan, Mallory M; Loewen, Christopher J R; Voelker, Dennis R

2014-02-28

Saccharomyces cerevisiae uses multiple biosynthetic pathways for the synthesis of phosphatidylethanolamine. One route involves the synthesis of phosphatidylserine (PtdSer) in the endoplasmic reticulum (ER), the transport of this lipid to endosomes, and decarboxylation by PtdSer decarboxylase 2 (Psd2p) to produce phosphatidylethanolamine. Several proteins and protein motifs are known to be required for PtdSer transport to occur, namely the Sec14p homolog PstB2p/Pdr17p; a PtdIns 4-kinase, Stt4p; and a C2 domain of Psd2p. The focus of this work is on defining the protein-protein and protein-lipid interactions of these components. PstB2p interacts with a protein encoded by the uncharacterized gene YPL272C, which we name Pbi1p (PstB2p-interacting 1). PstB2p, Psd2, and Pbi1p were shown to be lipid-binding proteins specific for phosphatidic acid. Pbi1p also interacts with the ER-localized Scs2p, a binding determinant for several peripheral ER proteins. A complex between Psd2p and PstB2p was also detected, and this interaction was facilitated by a cryptic C2 domain at the extreme N terminus of Psd2p (C2-1) as well the previously characterized C2 domain of Psd2p (C2-2). The predicted N-terminal helical region of PstB2p was necessary and sufficient for promoting the interaction with both Psd2p and Pbi1p. Taken together, these results support a model for PtdSer transport involving the docking of a PtdSer donor membrane with an acceptor via specific protein-protein and protein-lipid interactions. Specifically, our model predicts that this process involves an acceptor membrane complex containing the C2 domains of Psd2p, PstB2p, and Pbi1p that ligate to Scs2p and phosphatidic acid present in the donor membrane, forming a zone of apposition that facilitates PtdSer transfer.

Universal Approach toward Hysteresis-Free Perovskite Solar Cell via Defect Engineering.

PubMed

Son, Dae-Yong; Kim, Seul-Gi; Seo, Ja-Young; Lee, Seon-Hee; Shin, Hyunjung; Lee, Donghwa; Park, Nam-Gyu

2018-01-31

Organic-inorganic halide perovskite is believed to be a potential candidate for high efficiency solar cells because power conversion efficiency (PCE) was certified to be more than 22%. Nevertheless, mismatch of PCE due to current density (J)-voltage (V) hysteresis in perovskite solar cells is an obstacle to overcome. There has been much lively debate on the origin of J-V hysteresis; however, effective methodology to solve the hysteric problem has not been developed. Here we report a universal approach for hysteresis-free perovskite solar cells via defect engineering. A severe hysteresis observed from the normal mesoscopic structure employing TiO 2 and spiro-MeOTAD is almost removed or does not exist upon doping the pure perovskites, CH 3 NH 3 PbI 3 and HC(NH 2 ) 2 PbI 3 , and the mixed cation/anion perovskites, FA 0.85 MA 0.15 PbI 2.55 Br 0.45 and FA 0.85 MA 0.1 Cs 0.05 PbI 2.7 Br 0.3 , with potassium iodide. Substantial reductions in low-frequency capacitance and bulk trap density are measured from the KI-doped perovskite, which is indicative of trap-hysteresis correlation. A series of experiments with alkali metal iodides of LiI, NaI, KI, RbI and CsI reveals that potassium ion is the right element for hysteresis-free perovskite. Theoretical studies suggest that the atomistic origin of the hysteresis of perovskite solar cells is not the migration of iodide vacancy but results from the formation of iodide Frenkel defect. Potassium ion is able to prevent the formation of Frenkel defect since K + energetically prefers the interstitial site. A complete removal of hysteresis is more pronounced at mixed perovskite system as compared to pure perovskites, which is explained by lower formation energy of K interstitial (-0.65 V for CH 3 NH 3 PbI 3 vs -1.17 V for mixed perovskite). The developed KI doping methodology is universally adapted for hysteresis-free perovskite regardless of perovskite composition and device structure.

Android Platform Based Smartphones for a Logistical Remote Association Repair Framework

PubMed Central

Lien, Shao-Fan; Wang, Chun-Chieh; Su, Juhng-Perng; Chen, Hong-Ming; Wu, Chein-Hsing

2014-01-01

The maintenance of large-scale systems is an important issue for logistics support planning. In this paper, we developed a Logistical Remote Association Repair Framework (LRARF) to aid repairmen in keeping the system available. LRARF includes four subsystems: smart mobile phones, a Database Management System (DBMS), a Maintenance Support Center (MSC) and wireless networks. The repairman uses smart mobile phones to capture QR-codes and the images of faulty circuit boards. The captured QR-codes and images are transmitted to the DBMS so the invalid modules can be recognized via the proposed algorithm. In this paper, the Linear Projective Transform (LPT) is employed for fast QR-code calibration. Moreover, the ANFIS-based data mining system is used for module identification and searching automatically for the maintenance manual corresponding to the invalid modules. The inputs of the ANFIS-based data mining system are the QR-codes and image features; the output is the module ID. DBMS also transmits the maintenance manual back to the maintenance staff. If modules are not recognizable, the repairmen and center engineers can obtain the relevant information about the invalid modules through live video. The experimental results validate the applicability of the Android-based platform in the recognition of invalid modules. In addition, the live video can also be recorded synchronously on the MSC for later use. PMID:24967603

Connecting the solution chemistry of PbI2 and MAI: a cyclodextrin-based supramolecular approach to the formation of hybrid halide perovskites† †Electronic supplementary information (ESI) available: Experimental section; Section 1: solution characterization; Section 2: solar cell optimization and characterization; Section 3: thin film characterization; Section 4: advanced structural characterization. See DOI: 10.1039/c7sc05095j

PubMed Central

Masi, Sofia; Aiello, Federica; Listorti, Andrea; Balzano, Federica; Altamura, Davide; Giannini, Cinzia; Caliandro, Rocco; Uccello-Barretta, Gloria

2018-01-01

The evolution from solvated precursors to hybrid halide perovskite films dictates most of the photophysical and optoelectronic properties of the final polycrystalline material. Specifically, the complex equilibria and the importantly different solubilities of lead iodide (PbI2) and methylammonium iodide (MAI) induce inhomogeneous crystal growth, often leading to a defect dense film showing non-optimal optoelectronic properties and intrinsic instability. Here, we explore a supramolecular approach based on the use of cyclodextrins (CDs) to modify the underlying solution chemistry. The peculiar phenomenon demonstrated is a tunable complexation between different CDs and MA+ cations concurrent to an out of cage PbI2 intercalation, representing the first report of a connection between the solvation equilibria of the two perovskite precursors. The optimal conditions in terms of CD cavity size and polarity translate to a neat enhancement of PbI2 solubility in the reaction media, leading to an equilibration of the availability of the precursors in solution. The macroscopic result of this is an improved nucleation process, leading to a perovskite material with higher crystallinity, better optical properties and improved moisture resistance. Remarkably, the use of CDs presents a great potential for a wide range of device-related applications, as well as for the development of tailored composite materials. PMID:29732103

Do gingival soft tissues benefit from the application of a papilla preservation flap technique in endodontic surgery?

PubMed

Taschieri, Silvio; Corbella, Stefano; Del Fabbro, Massimo

2014-10-01

A healthy gingival condition after endodontic surgery may depend on adequate soft tissue management. The aim of this study was to compare 2 incision techniques, papilla base incision (PBI) and intrasulcular flap (IS), which are currently used in endodontic surgery. In the present nonrandomized controlled clinical trial, patients requiring endodontic surgery on a single tooth were enrolled. PBI was used in 1 group and IS was used in the other group. The primary outcomes were changes in periodontal probing depth, gingival recession, and height of the interproximal mesial and distal papillae. Outcome variables were assessed preoperatively and 6 months after surgery. Between-group differences were evaluated through appropriate statistical analysis, with significance set at a P value equal to .05. Each group was composed of 12 patients and the 2 groups were comparable at baseline. Two weeks after surgery, papilla height decreased significantly in the IS group (2.05 and 1.80 mm at the mesial and distal aspects, respectively), whereas no significant decrease in papilla height was observed in the PBI group (0.10 and 0.20 mm). No statistically significant difference between groups was observed after 6 months. No significant difference between groups was found for gingival recession or probing depth at any follow-up time. Better soft tissue preservation in the early postoperative period was achieved using the PBI approach compared with the IS approach. The PBI can be recommended for endodontic surgical procedures involving esthetic regions. Copyright © 2014 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Effect of Rubidium Incorporation on the Structural, Electrical, and Photovoltaic Properties of Methylammonium Lead Iodide-Based Perovskite Solar Cells.

PubMed

Park, Ik Jae; Seo, Seongrok; Park, Min Ah; Lee, Sangwook; Kim, Dong Hoe; Zhu, Kai; Shin, Hyunjung; Kim, Jin Young

2017-12-06

We report the electrical properties of rubidium-incorporated methylammonium lead iodide ((Rb x MA 1-x )PbI 3 ) films and the photovoltaic performance of (Rb x MA 1-x )PbI 3 film-based p-i-n-type perovskite solar cells (PSCs). The incorporation of a small amount of Rb + (x = 0.05) increases both the open circuit voltage (V oc ) and the short circuit photocurrent density (J sc ) of the PSCs, leading to an improved power conversion efficiency (PCE). However, a high fraction of Rb + incorporation (x = 0.1 and 0.2) decreases the J sc and thus the PCE, which is attributed to the phase segregation of the single tetragonal perovskite phase to a MA-rich tetragonal perovskite phase and a RbPbI 3 orthorhombic phase at high Rb fractions. Conductive atomic force microscopic and admittance spectroscopic analyses reveal that the single-phase (Rb 0.05 MA 0.95 )PbI 3 film has a high electrical conductivity because of a reduced deep-level trap density. We also found that Rb substitution enhances the diode characteristics of the PSC, as evidenced by the reduced reverse saturation current (J 0 ). The optimized (Rb x MA 1-x )PbI 3 PSCs exhibited a PCE of 18.8% with negligible hysteresis in the photocurrent-voltage curve. The results from this work enhance the understanding of the effect of Rb incorporation into organic-inorganic hybrid halide perovskites and enable the exploration of Rb-incorporated mixed perovskites for various applications, such as solar cells, photodetectors, and light-emitting diodes.

KENNEDY SPACE CENTER, FLA. - STS-120 Mission Specialists Piers Sellers and Michael Foreman are in the Space Station Processing Facility for hardware familiarization. The mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

NASA Image and Video Library

2003-07-18

KENNEDY SPACE CENTER, FLA. - STS-120 Mission Specialists Piers Sellers and Michael Foreman are in the Space Station Processing Facility for hardware familiarization. The mission will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility can be seen the U.S. Node 2 (at left) and the Japanese Experiment Module (JEM)’s Pressurized Module (at right). The Italian-built Node 2, the second of three Space Station connecting modules, attaches to the end of the U.S. Lab and will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and, later, Multipurpose Logistics Modules. It will provide the primary docking location for the Shuttle when a pressurized mating adapter is attached to Node 2. Installation of the module will complete the U.S. Core of the ISS. Node 2 is the designated payload for mission STS-120. No orbiter or launch date has been determined yet. The Pressurized Module is the first element of the JEM to be delivered to KSC. The JEM is Japan's primary contribution to the Station. It will enhance the unique research capabilities of the orbiting complex by providing an additional environment for astronauts to conduct science experiments. The JEM also includes an exposed facility (platform) for space environment experiments, a robotic manipulator system, and two logistics modules. The various JEM components will be assembled in space over the course of three Shuttle missions.

NASA Image and Video Library

2003-08-12

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility can be seen the U.S. Node 2 (at left) and the Japanese Experiment Module (JEM)’s Pressurized Module (at right). The Italian-built Node 2, the second of three Space Station connecting modules, attaches to the end of the U.S. Lab and will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and, later, Multipurpose Logistics Modules. It will provide the primary docking location for the Shuttle when a pressurized mating adapter is attached to Node 2. Installation of the module will complete the U.S. Core of the ISS. Node 2 is the designated payload for mission STS-120. No orbiter or launch date has been determined yet. The Pressurized Module is the first element of the JEM to be delivered to KSC. The JEM is Japan's primary contribution to the Station. It will enhance the unique research capabilities of the orbiting complex by providing an additional environment for astronauts to conduct science experiments. The JEM also includes an exposed facility (platform) for space environment experiments, a robotic manipulator system, and two logistics modules. The various JEM components will be assembled in space over the course of three Shuttle missions.

KSC-07pd2827

NASA Image and Video Library

2007-10-11

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility at NASA's Kennedy Space Center, members of the STS-123 crew get hands-on experience with the mission payload, the Kibo Experiment Logistics Module Pressurized Section. They are at the center for a crew equipment interface test, which allows familiarization with equipment they will use during the mission. Crew members are Commander Dominic Gorie, Pilot Gregory Johnson and Mission Specialists Richard Linnehan, Takao Doi, Robert Behnken, Gerrett Reisman and Michael Foreman. Doi represents the Japan Aerospace Exploration Agency. Reisman will remain on the space station after the mission as a flight engineer for Expedition 16. STS-123 will carry and install one of the components of the Japanese Experiment Module, or JEM. Known as Kibo, the JEM comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. The various components of JEM will be assembled in space over the course of three space shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the space shuttle Endeavour, targeted for launch in February 2008. Photo credit: NASA/Dimitrios Gerondidakis

KSC-07pd2828

NASA Image and Video Library

2007-10-11

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility at NASA's Kennedy Space Center, members of the STS-123 crew get hands-on experience with the mission payload, the Kibo Experiment Logistics Module Pressurized Section. They are at the center for a crew equipment interface test, which allows familiarization with equipment they will use during the mission. Crew members are Commander Dominic Gorie, Pilot Gregory Johnson and Mission Specialists Richard Linnehan, Takao Doi, Robert Behnken, Gerrett Reisman and Michael Foreman. Doi represents the Japan Aerospace Exploration Agency. Reisman will remain on the space station after the mission as a flight engineer for Expedition 16. STS-123 will carry and install one of the components of the Japanese Experiment Module, or JEM. Known as Kibo, the JEM comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. The various components of JEM will be assembled in space over the course of three space shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the space shuttle Endeavour, targeted for launch in February 2008. Photo credit: NASA/Dimitrios Gerondidakis

KSC-07pd2826

NASA Image and Video Library

2007-10-11

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility at NASA's Kennedy Space Center, members of the STS-123 crew learn more about the mission payload, the Kibo Experiment Logistics Module Pressurized Section. They are at the center for a crew equipment interface test, which allows familiarization with equipment they will use during the mission. Crew members are Commander Dominic Gorie, Pilot Gregory Johnson and Mission Specialists Richard Linnehan, Takao Doi, Robert Behnken, Gerrett Reisman and Michael Foreman. Doi represents the Japan Aerospace Exploration Agency. Reisman will remain on the space station after the mission as a flight engineer for Expedition 16. STS-123 will carry and install one of the components of the Japanese Experiment Module, or JEM. Known as Kibo, the JEM comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. The various components of JEM will be assembled in space over the course of three space shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the space shuttle Endeavour, targeted for launch in February 2008. Photo credit: NASA/Dimitrios Gerondidakis

Parental bonding and hoarding in obsessive-compulsive disorder.

PubMed

Chen, David; Bienvenu, O Joseph; Krasnow, Janice; Wang, Ying; Grados, Marco A; Cullen, Bernadette; Goes, Fernando S; Maher, Brion; Greenberg, Benjamin D; McLaughlin, Nicole C; Rasmussen, Steven A; Fyer, Abby J; Knowles, James A; McCracken, James T; Piacentini, John; Geller, Dan; Pauls, David L; Stewart, S Evelyn; Murphy, Dennis L; Shugart, Yin-Yao; Riddle, Mark A; Nestadt, Gerald; Samuels, Jack

2017-02-01

Hoarding behavior may indicate a clinically and possibly etiologically distinct subtype of obsessive-compulsive disorder (OCD). Empirical evidence supports a relationship between hoarding and emotional over-attachment to objects. However, little is known about the relationship between hoarding and parental attachment in OCD. The study sample included 894 adults diagnosed with DSM-IV OCD who had participated in family and genetic studies of OCD. Participants were assessed for Axis I disorders, personality disorders, and general personality dimensions. The Parental Bonding Instrument (PBI) was used to assess dimensions of perceived parental rearing (care, overprotection, and control). We compared parental PBI scores in the 334 hoarding and 560 non-hoarding participants, separately in men and women. We used logistic regression to evaluate the relationship between parenting scores and hoarding in women, adjusting for other clinical features associated with hoarding. In men, there were no significant differences between hoarding and non-hoarding groups in maternal or paternal parenting scores. In women, the hoarding group had a lower mean score on maternal care (23.4 vs. 25.7, p<0.01); a higher mean score on maternal protection (9.4 vs. 7.7, p<0.001); and a higher mean score on maternal control (7.0 vs. 6.2, p<0.05), compared to the non-hoarding group. The magnitude of the relationships between maternal bonding dimensions and hoarding in women did not change after adjustment for other clinical features. Women who reported low maternal care/high maternal protection had significantly greater odds of hoarding compared to women with high maternal care/low maternal protection (OR=2.54, 95% CI=1.60-4.02, p<0.001). Perceived poor maternal care, maternal overprotection, and maternal overcontrol are associated with hoarding in women with OCD. Parenting dimensions are not related to hoarding in men. These findings provide further support for a hoarding subtype of OCD and for sex-specific differences in etiologic pathways for hoarding in OCD. Copyright © 2016 Elsevier Inc. All rights reserved.

Parental bonding and hoarding in obsessive-compulsive disorder

PubMed Central

Chen, David; Bienvenu, O. Joseph; Krasnow, Janice; Wang, Ying; Grados, Marco A.; Cullen, Bernadette; Goes, Fernando S.; Maher, Brion; Greenberg, Benjamin D.; McLaughlin, Nicole C.; Rasmussen, Steven A.; Fyer, Abby J.; Knowles, James A.; McCracken, James T.; Piacentini, John; Geller, Dan; Pauls, David L.; Stewart, S. Evelyn; Murphy, Dennis L.; Shugart, Yin-Yao; Riddle, Mark A.; Nestadt, Gerald; Samuels, Jack

2017-01-01

Background Hoarding behavior may indicate a clinically and possibly etiologically distinct subtype of obsessive compulsive disorder (OCD). Empirical evidence supports a relationship between hoarding and emotional over-attachment to objects. However, little is known about the relationship between hoarding and parental attachment in OCD. Method The study sample included 894 adults diagnosed with DSM-IV OCD who had participated in family and genetic studies of OCD. Participants were assessed for Axis I disorders, personality disorders, and general personality dimensions. The Parental Bonding Instrument (PBI) was used to assess dimensions of perceived parental rearing (care, overprotection, and control). We compared parental PBI scores in the 334 hoarding and 560 non-hoarding participants, separately in men and women. We used logistic regression to evaluate the relationship between parenting scores and hoarding in women, adjusting for other clinical features associated with hoarding. Results In men, there were no significant differences between hoarding and non-hoarding groups in maternal or paternal parenting scores. In women, the hoarding group had a lower mean score on maternal care (23.4 vs. 25.7, p<0.01); a higher mean score on maternal protection (9.4 vs. 7.7, p<0.001); and a higher mean score on maternal control (7.0 vs. 6.2, p<0.05), compared to the non-hoarding group. The magnitude of the relationships between maternal bonding dimensions and hoarding in women did not change after adjustment for other clinical features. Women who reported low maternal care/high maternal protection had significantly greater odds of hoarding compared to women with high maternal care/low maternal protection (OR=2.54, 95% CI=1.60-4.02, p<0.001). Conclusions Perceived poor maternal care, maternal overprotection, and maternal overcontrol are associated with hoarding in women with OCD. Parenting dimensions are not related to hoarding in men. These findings provide further support for a hoarding subtype of OCD and for sex-specific differences in etiologic pathways for hoarding in OCD. PMID:27915218

Partial breast radiation for early-stage breast cancer.

PubMed

McCormick, Beryl

2012-02-01

This review is to provide an update on the current status of partial breast irradiation (PBI) for women presenting with early-stage breast cancer, as an alternate radiation technique to fractionated, whole breast radiation, following conservation surgery. As more women are asking for and receiving this treatment, both on and off protocols, understanding recent additions to the literature is important to physicians caring for this patient population. Newly published retrospective studies, with follow-up times out to 10 years and the status of both recently completed and still open large prospective phase III trials will be covered, with emphasis on unexpected side effects reported, and some hypothesis-generating radiobiology observations. A recent consensus treatment guideline for PBI use is also discussed. Selected retrospective studies continue to report outcomes matching those achieved with whole breast radiation; however, results from large prospective randomized trials comparing PBI to whole breast radiation have been reported only with short follow-up times, or in two studies, are still pending. A recent consensus guideline is useful at present in selecting patients for discussion of this treatment.

Controllable Growth of Perovskite Films by Room-Temperature Air Exposure for Efficient Planar Heterojunction Photovoltaic Cells.

PubMed

Yang, Bin; Dyck, Ondrej; Poplawsky, Jonathan; Keum, Jong; Das, Sanjib; Puretzky, Alexander; Aytug, Tolga; Joshi, Pooran C; Rouleau, Christopher M; Duscher, Gerd; Geohegan, David B; Xiao, Kai

2015-12-01

A two-step solution processing approach has been established to grow void-free perovskite films for low-cost high-performance planar heterojunction photovoltaic devices. A high-temperature thermal annealing treatment was applied to drive the diffusion of CH3NH3I precursor molecules into a compact PbI2 layer to form perovskite films. However, thermal annealing for extended periods led to degraded device performance owing to the defects generated by decomposition of perovskite into PbI2. A controllable layer-by-layer spin-coating method was used to grow "bilayer" CH3NH3I/PbI2 films, and then drive the interdiffusion between PbI2 and CH3NH3I layers by a simple air exposure at room temperature for making well-oriented, highly crystalline perovskite films without thermal annealing. This high degree of crystallinity resulted in a carrier diffusion length of ca. 800 nm and a high device efficiency of 15.6%, which is comparable to values reported for thermally annealed perovskite films. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Activity of the hypophyseal-thyroid gland system in relation to the funcitonal state of the sex glands. Report I].

PubMed

Babichev, V N; Samsonova, V M

1975-01-01

Experiments were conducted on intact female rats; it was revealed that the content of protein-bound iodine (PBI) in the blood depended on the stage of the estral cycle. It was decreased at the metestrus and diestrus stages. Castration produced an even greater reduction in the blood PBI content. The blood PBI content proved to elevate in administration of estradiol dipropionate (EDP) to castrated rats. The TSH content in the hypophysis increased at the metestrus and diestrus stages and decreased at the proestrus and estrus stages. The relationship was reverse in the case with the blood TTH content. Castration was followed by a marked increase in the TSH content in the hypophysis accompanied by a reduction in the blood hormone level. The TSH concentration in the hypophysis decreased and in the blood increased under the effect of EDP in castrated animals. The data obtained indicated that the interrelationship between the thyroid gland and the sex glands was realized at the level of the hypophysis, and possibly, of the hypothalamus.

Perylene bisimide hydrogels and lyotropic liquid crystals with temperature-responsive color change† †Electronic supplementary information (ESI) available: Detailed procedures and results for all reported experiments, along with synthetic details for PBI 1. See DOI: 10.1039/c6sc02249a Click here for additional data file.

PubMed Central

Görl, Daniel; Soberats, Bartolome; Herbst, Stefanie; Stepanenko, Vladimir

2016-01-01

The self-assembly of perylene bisimide (PBI) dyes bearing oligo ethylene glycol (OEG) units in water affords responsive functional nanostructures characterized by their lower critical solution temperature (LCST). Tuning of the LCST is realized by a supramolecular approach that relies on two structurally closely related PBI–OEG molecules. The two PBIs socially co-assemble in water and the resulting nanostructures exhibit a single LCST in between the transition temperatures of the aggregates formed by single components. This permits to precisely tune the transition from a hydrogel to a lyotropic liquid crystal state at temperatures between 26 and 51 °C by adjusting the molar fraction of the two PBIs. Owing to concomitant changes in PBI–PBI interactions this phase transition affords a pronounced color change with “fluorescence-on” response that can be utilized as a smart temperature sensory system. PMID:28451124

Planar structured perovskite solar cells by hybrid physical chemical vapor deposition with optimized perovskite film thickness

NASA Astrophysics Data System (ADS)

Wei, Xiangyang; Peng, Yanke; Jing, Gaoshan; Cui, Tianhong

2018-05-01

The thickness of perovskite absorber layer is a critical parameter to determine a planar structured perovskite solar cell’s performance. By modifying the spin coating speed and PbI2/N,N-dimethylformamide (DMF) solution concentration, the thickness of perovskite absorber layer was optimized to obtain high-performance solar cells. Using a PbI2/DMF solution of 1.3 mol/L, maximum power conversion efficiency (PCE) of a perovskite solar cell is 15.5% with a perovskite film of 413 nm at 5000 rpm, and PCE of 14.3% was also obtained for a solar cell with a perovskite film of 182 nm thick. It is derived that higher concentration of PbI2/DMF will result in better perovskite solar cells. Additionally, these perovskite solar cells are highly uniform. In 14 sets of solar cells, standard deviations of 11 sets of solar cells were less than 0.50% and the smallest standard deviation was 0.25%, which demonstrates the reliability and effectiveness of hybrid physical chemical vapor deposition (HPCVD) method.

Carrier injection and recombination processes in perovskite CH3NH3PbI3 solar cells studied by electroluminescence spectroscopy

NASA Astrophysics Data System (ADS)

Handa, Taketo; Okano, Makoto; Tex, David M.; Shimazaki, Ai; Aharen, Tomoko; Wakamiya, Atsushi; Kanemitsu, Yoshihiko

2016-02-01

Organic-inorganic hybrid perovskite materials, CH3NH3PbX3 (X = I and Br), are considered as promising candidates for emerging thin-film photovoltaics. For practical implementation, the degradation mechanism and the carrier dynamics during operation have to be clarified. We investigated the degradation mechanism and the carrier injection and recombination processes in perovskite CH3NH3PbI3 solar cells using photoluminescence (PL) and electroluminescence (EL) imaging spectroscopies. By applying forward bias-voltage, an inhomogeneous distribution of the EL intensity was clearly observed from the CH3NH3PbI3 solar cells. By comparing the PL- and EL-images, we revealed that the spatial inhomogeneity of the EL intensity is a result of the inhomogeneous luminescence efficiency in the perovskite layer. An application of bias-voltage for several tens of minutes in air caused a decrease in the EL intensity and the conversion efficiency of the perovskite solar cells. The degradation mechanism of perovskite solar cells under bias-voltage in air is discussed.

Evolution of Photoluminescence, Raman, and Structure of CH3NH3PbI3 Perovskite Microwires Under Humidity Exposure

NASA Astrophysics Data System (ADS)

Segovia, Rubén; Qu, Geyang; Peng, Miao; Sun, Xiudong; Shi, Hongyan; Gao, Bo

2018-03-01

Self-assembled organic-inorganic CH3NH3PbI3 perovskite microwires (MWs) upon humidity exposure along several weeks were investigated by photoluminescence (PL) spectroscopy, Raman spectroscopy, and X-ray diffraction (XRD). We show that, in addition to the common perovskite decomposition into PbI2 and the formation of a hydrated phase, humidity induced a gradual PL redshift at the initial weeks that is stabilized for longer exposure ( 21 nm over the degradation process) and an intensity enhancement. Original perovskite Raman band and XRD reflections slightly shifted upon humidity, indicating defects formation and structure distortion of the MWs crystal lattice. By correlating the PL, Raman, and XRD results, it is believed that the redshift of the MWs PL emission was originated from the structural disorder caused by the incorporation of H2O molecules in the crystal lattice and radiative recombination through moisture-induced subgap trap states. Our study provides insights into the optical and structural response of organic-inorganic perovskite materials upon humidity exposure.

Elucidating the Key Role of a Lewis Base Solvent in the Formation of Perovskite Films Fabricated from the Lewis Adduct Approach.

PubMed

Cao, Xiaobing; Zhi, Lili; Li, Yahui; Fang, Fei; Cui, Xian; Yao, Youwei; Ci, Lijie; Ding, Kongxian; Wei, Jinquan

2017-09-27

High-quality perovskite films can be fabricated from Lewis acid-base adducts through molecule exchange. Substantial work is needed to fully understand the formation mechanism of the perovskite films, which helps to further improve their quality. Here, we study the formation of CH 3 NH 3 PbI 3 perovskite films by introducing some dimethylacetamide into the PbI 2 /N,N-dimethylformamide solution. We reveal that there are three key processes during the formation of perovskite films through the Lewis acid-base adduct approach: molecule intercalation of solvent into the PbI 2 lattice, molecule exchange between the solvent and CH 3 NH 3 I, and dissolution-recrystallization of the perovskite grains during annealing. The Lewis base solvents play multiple functions in the above processes. The properties of the solvent, including Lewis basicity and boiling point, play key roles in forming smooth perovskite films with large grains. We also provide some rules for choosing Lewis base additives to prepare high-quality perovskite films through the Lewis adduct approach.

Penetrating brain injury with a metal bar and a knife: Report of two interesting cases.

PubMed

Tabibkhooei, Alireza; Taheri, Morteza; Rohani, Sadra; Chanideh, Iran; Rahatlou, Hessam

2018-04-01

Introduction Penetrating brain injury (PBI) is uncommon among the civilian population. Here, we report two interesting cases of PBI. Case presentation The first patient was a 20-year-old male who sustained a penetrating head injury with a metal bar during an accident at work. The patient underwent early surgical intervention, and related meningitis was treated with antibiotics. The patient was discharged 45 days later with no deficit. The second patient was a 34-year-old male who was the victim of a violence attack and was admitted to hospital. He was struck by a knife to his right temporal bone. A brain computed tomography scan and magnetic resonance imaging (MRI) demonstrated the tract of the knife within the brain parenchyma. The patient underwent conservative treatment. After several weeks, the patient was discharged in good health. Conclusion Although severe PBI has a poorer prognosis than a blunt brain injury, in treating of these patients, aggressive and timely surgical intervention, proper wide-spectrum antibiotic administration, stringent and diligent care in the intensive-care unit and careful management of the associated complications are mandated.

Positive attitudinal shifts with the Physics by Inquiry curriculum across multiple implementations

NASA Astrophysics Data System (ADS)

Lindsey, Beth A.; Hsu, Leonardo; Sadaghiani, Homeyra; Taylor, Jack W.; Cummings, Karen

2012-06-01

Recent publications have documented positive attitudinal shifts on the Colorado Learning Attitudes about Science Survey (CLASS) among students enrolled in courses with an explicit epistemological focus. We now report positive attitudinal shifts in classes using the Physics by Inquiry (PbI) curriculum, which has only an implicit focus on student epistemologies and nature of science issues. These positive shifts have occurred in several different implementations of the curriculum, across multiple institutions and multiple semesters. In many classes, students experienced significant attitudinal shifts in the problem-solving categories of the CLASS, despite the conceptual focus of most PbI courses.

Structural and thermodynamic aspects of organic-inorganic mixed halide (CH3NH3PbI3-xBrx) perovskite

NASA Astrophysics Data System (ADS)

Singh, Rajan Kumar; Kumar, Ranveer; Jain, Neha; Singh, Jai; Mishra, S. K.

2018-05-01

Mixed Bromine and iodine lead halide perovskite CH3NH3PbI3-xBrx have been synthesized by solution phase method using CH3NH3I and PbBr2 precursors in ambient conditions. X-ray diffraction indicates the formation of cubic perovskite at room temperature with space group of Pm3m. The mixed perovskite improved crystallanity and grain contour which may significant improve photovoltaic performance of perovskite devices. Thermodynamic behavior of such type of material also indicates energy absorption nature of materials.

Solid state perovskite solar modules by vacuum-vapor assisted sequential deposition on Nd:YVO₄ laser patterned rutile TiO₂ nanorods.

PubMed

Fakharuddin, Azhar; Palma, Alessandro L; Di Giacomo, Francesco; Casaluci, Simone; Matteocci, Fabio; Wali, Qamar; Rauf, Muhammad; Di Carlo, Aldo; Brown, Thomas M; Jose, Rajan

2015-12-11

The past few years have witnessed remarkable progress in solution-processed methylammonium lead halide (CH3NH3PbX3, X = halide) perovskite solar cells (PSCs) with reported photoconversion efficiency (η) exceeding 20% in laboratory-scale devices and reaching up to 13% in their large area perovskite solar modules (PSMs). These devices mostly employ mesoporous TiO2 nanoparticles (NPs) as an electron transport layer (ETL) which provides a scaffold on which the perovskite semiconductor can grow. However, limitations exist which are due to trap-limited electron transport and non-complete pore filling. Herein, we have employed TiO2 nanorods (NRs), a material offering a two-fold higher electronic mobility and higher pore-filing compared to their particle analogues, as an ETL. A crucial issue in NRs' patterning over substrates is resolved by using precise Nd:YVO4 laser ablation, and a champion device with η ∼ 8.1% is reported via a simple and low cost vacuum-vapor assisted sequential processing (V-VASP) of a CH3NH3PbI3 film. Our experiments showed a successful demonstration of NRs-based PSMs via the V-VASP technique which can be applied to fabricate large area modules with a pin-hole free, smooth and dense perovskite layer which is required to build high efficiency devices.

Highly Controlled Codeposition Rate of Organolead Halide Perovskite by Laser Evaporation Method.

PubMed

Miyadera, Tetsuhiko; Sugita, Takeshi; Tampo, Hitoshi; Matsubara, Koji; Chikamatsu, Masayuki

2016-10-05

Organolead-halide perovskites can be promising materials for next-generation solar cells because of its high power conversion efficiency. The method of precise fabrication is required because both solution-process and vacuum-process fabrication of the perovskite have problems of controllability and reproducibility. Vacuum deposition process was expected to achieve precise control; however, vaporization of amine compound significantly degrades the controllability of deposition rate. Here we achieved the reduction of the vaporization by implementing the laser evaporation system for the codeposition of perovskite. Locally irradiated continuous-wave lasers on the source materials realized the reduced vaporization of CH 3 NH 3 I. The deposition rate was stabilized for several hours by adjusting the duty ratio of modulated laser based on proportional-integral control. Organic-photovoltaic-type perovskite solar cells were fabricated by codeposition of PbI 2 and CH 3 NH 3 I. A power-conversion efficiency of 16.0% with reduced hysteresis was achieved.

Raffaello Multi-Purpose Logistics Module (MPLM) in the Endeavour payload bay prior to docking

NASA Image and Video Library

2001-04-21

ISS002-E-5815 (21 April 2001) --- The Raffaello Multi-Purpose Logistics Module (MPLM), built by the Italian Space Agency (ASI), sits in its berthed position in the cargo bay of the Space Shuttle Endeavour as the STS-100 crew eases the vehicle close to the International Space Station (ISS) for docking. The image was recorded with a digital still camera by one of the Expedition Two crew members aboard the Station.

ZnO-Assisted Growth of CH3NH3PbI3- xCl x Film and Efficient Planar Perovskite Solar Cells with a TiO2/ZnO/C60 Electron Transport Trilayer.

PubMed

Xu, Jia; Fang, Mingde; Chen, Jing; Zhang, Bing; Yao, Jianxi; Dai, Songyuan

2018-06-06

Appropriate electron transport layers (ETL) are essential in perovskite solar cells (PSCs) with high power conversion efficiency (PCE). Herein, a TiO 2 /ZnO/C 60 trilayer fabricated on a transparent fluorine-doped tin oxide (FTO) glass substrate is used as a compound ETL in planar PSCs. The trilayer shows positive effects on both perovskite synthesis and device performance. The ZnO layer assists growth of CH 3 NH 3 PbI 3- x Cl x ( x ≈ 0) annealed at a lower temperature and with a shorter time, which is due to a more rapid and easier decomposition of the intermediate CH 3 NH 3 PbCl 3 phase in the growth of CH 3 NH 3 PbI 3- x Cl x . All three materials in the trilayer are important for obtaining PSCs with a high PCE. ZnO is critical for enhancing the open circuit voltage by ensuring proper energy alignment with the TiO 2 and C 60 layers. C 60 enhances carrier extraction from the CH 3 NH 3 PbI 3- x Cl x layer. TiO 2 eliminates charge recombination at the FTO surface and ensures efficient electron collection. The best-performing PSC based on the TiO 2 /ZnO/C 60 electron transport trilayer features a PCE of 18.63% with a fill factor of 79.12%. These findings help develop an understanding of the effects of ZnO-containing ETLs on perovskite film synthesis and show promise for the future development of high-performance PSCs with compound ETLs.

Development of a tool for assessment and care planning for dementia-related problem behaviors in home and community-based services programs: the Problem Behavior Inventory.

PubMed

Phillips, V L; Diwan, Sadhna; Egner, Amanda

2002-01-01

To describe development, validity, and application of the Problem Behavior Inventory (PBI), a tool to assess dementia-related problem behaviors (DRPBs) in community-based populations. Demographic, contact, and disease-specific data were extracted from client files from a Medicaid-funded home and community-based services program. Primary caregivers completed standard surveys relating to the care recipients' memory, mood, and behaviors. The client (care recipient) completed the Mini-Mental Status Exam (MMSE). Cognitively impaired clients, enrolled in the Community Care Services Program (CCSP) during a reference month, and their primary caregivers, were identified by CCSP case managers for participation in the study. Primary caregivers completed the Revised Memory and Behavior Problem Checklist (RMBPC). Clients screening positive for the presence of DRPBs based on caregiver responses to the RMBPC were then assessed using the Problem Behavior Inventory (PBI). Within the CCSP sample, the most prevalent behavior was appearing sad or depressed (67%), while the most frequent behavior was seeking attention, occurring at least daily in 58% of the group. The most bothersome behaviors were being sexually inappropriate, wandering, and misbehaving in public. Examination by behavior category (physical, verbal, mood, etc.) revealed a strong relationship between level of bother and behavior frequency. Frequency of verbal behaviors was positively related to MMSE scores, whereas frequency of ADL-related behaviors was inversely related to MMSE scores. Bother scores were not associated with MMSE scores. This study documents that the PBI is a valid, useful, and feasible tool for assessing DRPBs in community populations. Case managers using the PBI can determine specific problem behavior areas among client populations and for individual clients and institute client-specific interventions to address each issue.

Journey of oocyte from metaphase-I to metaphase-II stage in mammals.

PubMed

Sharma, Alka; Tiwari, Meenakshi; Gupta, Anumegha; Pandey, Ashutosh N; Yadav, Pramod K; Chaube, Shail K

2018-08-01

In mammals, journey from metaphase-I (M-I) to metaphase-II (M-II) is important since oocyte extrude first polar body (PB-I) and gets converted into haploid gamete. The molecular and cellular changes associated with meiotic cell cycle progression from M-I to M-II stage and extrusion of PB-I remain ill understood. Several factors drive oocyte meiosis from M-I to M-II stage. The mitogen-activated protein kinase3/1 (MAPK3/1), signal molecules and Rho family GTPases act through various pathways to drive cell cycle progression from M-I to M-II stage. The down regulation of MOS/MEK/MAPK3/1 pathway results in the activation of anaphase-promoting complex/cyclosome (APC/C). The active APC/C destabilizes maturation promoting factor (MPF) and induces meiotic resumption. Several signal molecules such as, c-Jun N-terminal kinase (JNK2), SENP3, mitotic kinesin-like protein 2 (MKlp2), regulator of G-protein signaling (RGS2), Epsin2, polo-like kinase 1 (Plk1) are directly or indirectly involved in chromosomal segregation. Rho family GTPase is another enzyme that along with cell division cycle (Cdc42) to form actomyosin contractile ring required for chromosomal segregation. In the presence of origin recognition complex (ORC4), eccentrically localized haploid set of chromosomes trigger cortex differentiation and determine the division site for polar body formation. The actomyosin contractile activity at the site of division plane helps to form cytokinetic furrow that results in the formation and extrusion of PB-I. Indeed, oocyte journey from M-I to M-II stage is coordinated by several factors and pathways that enable oocyte to extrude PB-I. Quality of oocyte directly impact fertilization rate, early embryonic development, and reproductive outcome in mammals. © 2018 Wiley Periodicals, Inc.

Shallow halogen vacancies in halide optoelectronic materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Hongliang; Du, Mao -Hua

2014-11-05

Halogen vacancies (V H) are usually deep color centers (F centers) in halides and can act as major electron traps or recombination centers. The deep V H contributes to the typically poor carrier transport properties in halides. However, several halides have recently emerged as excellent optoelectronic materials, e.g., CH 3NH 3PbI 3 and TlBr. Both CH 3NH 3PbI 3 and TlBr have been found to have shallow V H, in contrast to commonly seen deep V H in halides. In this paper, several halide optoelectronic materials, i.e., CH 3NH 3PbI 3, CH 3NH 3SnI 3 (photovoltaic materials), TlBr, and CsPbBrmore » 3, (gamma-ray detection materials) are studied to understand the material chemistry and structure that determine whether V H is a shallow or deep defect in a halide material. It is found that crystal structure and chemistry of ns 2 ions both play important roles in creating shallow V H in halides such as CH 3NH 3PbI 3, CH 3NH 3SnI 3, and TlBr. The key to identifying halides with shallow V H is to find the right crystal structures and compounds that suppress cation orbital hybridization at V H, such as those with long cation-cation distances and low anion coordination numbers, and those with crystal symmetry that prevents strong hybridization of cation dangling bond orbitals at V H. Furthermore, the results of this paper provide insight and guidance to identifying halides with shallow V H as good electronic and optoelectronic materials.« less

Distinct Roles of Protein Disulfide Isomerase and P5 Sulfhydryl Oxidoreductases in Multiple Pathways for Oxidation of Structurally Diverse Storage Proteins in Rice[W][OA

PubMed Central

Onda, Yayoi; Nagamine, Ai; Sakurai, Mutsumi; Kumamaru, Toshihiro; Ogawa, Masahiro; Kawagoe, Yasushi

2011-01-01

In the rice (Oryza sativa) endosperm, storage proteins are synthesized on the rough endoplasmic reticulum (ER), in which prolamins are sorted to protein bodies (PBs) called type-I PB (PB-I). Protein disulfide isomerase (PDI) family oxidoreductase PDIL2;3, an ortholog of human P5, contains a conserved structural disulfide in the redox-inactive thioredoxin-like (TRX) domain and was efficiently targeted to the surface of PB-I in a redox active site–dependent manner, whereas PDIL1;1, an ortholog of human PDI, was localized in the ER lumen. Complementation analyses using PDIL1;1 knockout esp2 mutant indicated that the a and a′ TRX domains of PDIL1;1 exhibited similar redox activities and that PDIL2;3 was unable to perform the PDIL1;1 functions. PDIL2;3 knockdown inhibited the accumulation of Cys-rich 10-kD prolamin (crP10) in the core of PB-I. Conversely, crP10 knockdown dispersed PDIL2;3 into the ER lumen. Glutathione S-transferase-PDIL2;3 formed a stable tetramer when it was expressed in Escherichia coli, and the recombinant PDIL2;3 tetramer facilitated α-globulin(C79F) mutant protein to form nonnative intermolecular disulfide bonds in vitro. These results indicate that PDIL2;3 and PDIL1;1 are not functionally redundant in sulfhydryl oxidations of structurally diverse storage proteins and play distinct roles in PB development. We discuss PDIL2;3-dependent and PDIL2;3-independent oxidation pathways that sustain disulfide bonds of crP10 in PB-I. PMID:21278127

[Increasing the resolution of chromosome analysis using pyrido[1,2alpha]benzimidazoles].

PubMed

Rachinskaia, O A; Popov, K V; Ryzvanovich, G A; Bol'sheva, N L; Begunov, R S; Iurkevich, O Iu; Zelenin, A V; Muravlenko, O V

2012-10-01

We studied the influence of three derivatives of pyrido[1,2alpha]benzimidazoles (PBIs), which have DNA-intercalating properties, on plant mitotic chromosome condensation, in order to increase the resolution of chromosome analysis. The efficiency of the influence of these agents was assessed using the median chromosome length on chromosome slides, as well as by the number and size of chromosome DAPI bands. We used the third chromosome of Linum grandiflorum Desf. in these experiments. The chromosome was identified on the slides using its DAPI band pattern and a molecular marker, viz., the 5S rDNA site, which is located in the proximal region of the long arm of the chromosome. The influence of the well-known 9-aminoacridine (9-AMA) DNA intercalator, which is widely used in karyotype studies of short-chromosome organisms, was used as a control in all of the experiments. It was found that the influence of each of the three PBIs in the study on the root meristem of L. grandiflorum resulted in an increase in the median length of the third chromosome, the linear centromeric DAPI band size, and the number ofintercalary DAPI bands. All three PBIs acted more efficiently than 9-AMA. The median chromosome length was increased by 15-40% and the number of intercalary bands increased by 1.5-3 times after PBI treatment, as compared to 9-AMA treatment. At the same time, 7-CF3-PBI, in a similar manner to 9-AMA, did not change the relative size of the centromeric DAPI band, while 7-NH2-PBI and 7-CF3-9-NH2-PBI gradually increased this parameter. It is concluded that these substances can be used as intercalating agents in cytogenetic studies in order to increase the resolution of chromosome analysis.

Probabilistic images (PBIS): A concise image representation technique for multiple parameters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, L.C.; Yeh, S.H.; Chen, Z.

1984-01-01

Based on m parametric images (PIs) derived from a dynamic series (DS), each pixel of DS is regarded as an m-dimensional vector. Given one set of normal samples (pixels) N and another of abnormal samples A, probability density functions (pdfs) of both sets are estimated. Any unknown sample is classified into N or A by calculating the probability of its being in the abnormal set using the Bayes' theorem. Instead of estimating the multivariate pdfs, a distance ratio transformation is introduced to map the m-dimensional sample space to one dimensional Euclidean space. Consequently, the image that localizes the regional abnormalitiesmore » is characterized by the probability of being abnormal. This leads to the new representation scheme of PBIs. Tc-99m HIDA study for detecting intrahepatic lithiasis (IL) was chosen as an example of constructing PBI from 3 parameters derived from DS and such a PBI was compared with those 3 PIs, namely, retention ratio image (RRI), peak time image (TNMAX) and excretion mean transit time image (EMTT). 32 normal subjects and 20 patients with proved IL were collected and analyzed. The resultant sensitivity and specificity of PBI were 97% and 98% respectively. They were superior to those of any of the 3 PIs: RRI (94/97), TMAX (86/88) and EMTT (94/97). Furthermore, the contrast of PBI was much better than that of any other image. This new image formation technique, based on multiple parameters, shows the functional abnormalities in a structural way. Its good contrast makes the interpretation easy. This technique is powerful compared to the existing parametric image method.« less

Salivary markers of oxidative stress are related to age and oral health in adult non-smokers.

PubMed

Celecová, Viera; Kamodyová, Natália; Tóthová, Lubomíra; Kúdela, Matúš; Celec, Peter

2013-03-01

Salivary concentrations of thiobarbituric acid-reacting substances (TBARS) are associated with the periodontal status assessed as papillary bleeding index (PBI). Whether this association is age independent is currently unclear. Salivary concentrations of advanced oxidation protein products (AOPPs) and advanced glycation end products (AGEs) have not been assessed in relation to age or oral health yet. The aim of our study was to analyse salivary markers of oxidative stress in dental patients in relation to age, gender and oral health. Consecutive adult non-smoking dental patients were enrolled (n = 204; aged 19-83 years). PBI and the caries index (CI) were assessed. Markers of oxidative stress, such as TBARS, AOPPs and AGEs, and the total antioxidant capacity (TAC) were measured in saliva samples taken before clinical examination. Linear regression showed that salivary TBARS, AGEs and TAC significantly increase with age (r squared = 5.3%, 2.1% and 5%, respectively). PBI is an independent predictor of salivary TBARS (r squared = 5.5%), and the CI negatively affected AOPPs (r = 3.2%) and positively affected TBARS (r = 2.5%). Gender did not affect any of the analysed parameters. Age as a significant contributor to the variance should be taken into account in studies focusing on salivary markers of oxidative stress. The relationship between PBI and salivary TBARS confirms results from previous studies. In addition, our results show that the association is age independent. Negative association between the CI and AOPPs might be related to recent findings that AOPP might be actually a marker of non-enzymatic antioxidant status. © 2012 John Wiley & Sons A/S. All rights reserved.

Interfacial Interactions in Monolayer and Few-Layer SnS/CH3 NH3 PbI3 Perovskite van der Waals Heterostructures and Their Effects on Electronic and Optical Properties.

PubMed

Li, Jian-Cai; Wei, Zeng-Xi; Huang, Wei-Qing; Ma, Li-Li; Hu, Wangyu; Peng, Ping; Huang, Gui-Fang

2018-02-05

A high light-absorption coefficient and long-range hot-carrier transport of hybrid organic-inorganic perovskites give huge potential to their composites in solar energy conversion and environmental protection. Understanding interfacial interactions and their effects are paramount for designing perovskite-based heterostructures with desirable properties. Herein, we systematically investigated the interfacial interactions in monolayer and few-layer SnS/CH 3 NH 3 PbI 3 heterostructures and their effects on the electronic and optical properties of these structures by density functional theory. It was found that the interfacial interactions in SnS/CH 3 NH 3 PbI 3 heterostructures were van der Waals (vdW) interactions, and they were found to be insensitive to the layer number of 2D SnS sheets. Interestingly, although their band gap decreased upon increasing the layer number of SnS, the near-gap electronic states and optical absorption spectra of these heterostructures were found to be strikingly similar. This feature was determined to be critical for the design of 2D layered SnS-based heterostructures. Strong absorption in the ultraviolet and visible-light regions, type II staggered band alignment at the interface, and few-layer SnS as an active co-catalyst make 2D SnS/CH 3 NH 3 PbI 3 heterostructures promising candidates for photocatalysis, photodetectors, and solar energy harvesting and conversion. These results provide first insight into the nature of interfacial interactions and are useful for designing hybrid organic-inorganic perovskite-based devices with novel properties. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Gas Transport Properties of Polybenzimidazole and Poly(Phenylene Oxide) Mixed Matrix Membranes Incorporated with PDA-Functionalised Titanate Nanotubes

NASA Astrophysics Data System (ADS)

Giel, V.; Perchacz, M.; Kredatusová, J.; Pientka, Z.

2017-01-01

Functionalised titanate nanotubes (TiNTs) were incorporated to poly(5,5-bisbenzimidazole-2,2-diyl-1,3-phenylene) (PBI) or poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) for improving the interfacial compatibility between the polymer matrix and inorganic material and for altering the gas separation performance of the neat polymer membranes. Functionalisation consisted in oxidative polymerisation of dopamine-hydrochloride on the surface of non-functionalised TiNTs. Transmission electron microscopy (TEM) confirmed that a thin polydopamine (PDA) layer was created on the surface of TiNTs. 1.5, 3, 6, and 9 wt.% of PDA-functionalised TiNTs (PDA-TiNTs) were dispersed to each type of polymer matrix to create so-called mixed matrix membranes (MMMs). Infrared spectroscopy confirmed that -OH and -NH groups exist on the surface of PDA-TiNTs and that the nanotubes interact via H-bonding with PBI but not with PPO. The distribution of PDA-TiNTs in the MMMs was to some extent uniform as scanning electron microscope (SEM) studies showed. Beyond, PDA-TiNTs exhibit positive effect on gas transport properties, resulting in increased selectivities of MMMs. The addition of nanotubes caused a decrease in permeabilities but an increase in selectivities. It is shown that 9 wt.% of PDA-TiNTs in PBI gave a rise to CO2/N2 and CO2/CH4 selectivities of 112 and 63 %, respectively. In case of PPO-PDA-TiNT MMMs, CO2/N2 and CO2/CH4 selectivity increased about 25 and 17 %, respectively. Sorption measurement showed that the presence of PDA-TiNTs in PBI caused an increase in CO2 sorption, whereas the influence on other gases is less noticeable.

[Oral health status of women with normal and high-risk pregnancies].

PubMed

Chaloupka, P; Korečko, V; Turek, J; Merglová, V

2014-01-01

The aim of this study was to compare the oral health status of women with normal pregnancies and those with high-risk pregnancies. A total of 142 women in the third trimester of pregnancy were randomly selected for this study. The pregnant women were divided into two groups: a normal pregnancy group (group F, n = 61) and a high-risk pregnancy group (group R, n = 81). The following variables were recorded for each woman: age, general health status, DMF index, CPITN index, PBI index, amounts of Streptococcus mutans in the saliva and dental treatment needs. The data obtained were analysed statistically. The Mann-Whitney test, Kruskal-Wallis test and chi square test were used, and p-values less than 0.05 were considered statistically significant. The two-sided t-test was used to compare the two cohorts. Women with high-risk pregnancies showed increased values in all measured indices and tests, but there were no statistically significant differences between the two groups in the DMF index, CPITN index and amounts of Streptococcus mutans present in the saliva. Statistically significant differences were detected between the two groups for the PBI index and dental treatment needs. In group F, the maximum PBI index value was 2.9 in group F and 3.8 in group R. Significant differences were found also in mean PBI values. Out of the entire study cohort, 94 women (66.2%) required dental treatment, including 52% (n = 32) of the women with normal pregnancies and 77% (n = 62) of the women with high-risk pregnancies. This study found that women with complications during pregnancy had severe gingivitis and needed more frequent dental treatment than women with normal pregnancies.

Formation of Long-Lived Color Centers for Broadband Visible Light Emission in Low-Dimensional Layered Perovskites.

PubMed

Booker, Edward P; Thomas, Tudor H; Quarti, Claudio; Stanton, Michael R; Dashwood, Cameron D; Gillett, Alexander J; Richter, Johannes M; Pearson, Andrew J; Davis, Nathaniel J L K; Sirringhaus, Henning; Price, Michael B; Greenham, Neil C; Beljonne, David; Dutton, Siân E; Deschler, Felix

2017-12-27

We investigate the origin of the broadband visible emission in layered hybrid lead-halide perovskites and its connection with structural and photophysical properties. We study ⟨001⟩ oriented thin films of hexylammonium (HA) lead iodide, (C 6 H 16 N) 2 PbI 4 , and dodecylammonium (DA) lead iodide, (C 12 H 28 N) 2 PbI 4 , by combining first-principles simulations with time-resolved photoluminescence, steady-state absorption and X-ray diffraction measurements on cooling from 300 to 4 K. Ultrafast transient absorption and photoluminescence measurements are used to track the formation and recombination of emissive states. In addition to the excitonic photoluminescence near the absorption edge, we find a red-shifted, broadband (full-width at half-maximum of about 0.4 eV), emission band below 200 K, similar to emission from ⟨110⟩ oriented bromide 2D perovskites at room temperature. The lifetime of this sub-band-gap emission exceeds that of the excitonic transition by orders of magnitude. We use X-ray diffraction measurements to study the changes in crystal lattice with temperature. We report changes in the octahedral tilt and lattice spacing in both materials, together with a phase change around 200 K in DA 2 PbI 4 . DFT simulations of the HA 2 PbI 4 crystal structure indicate that the low-energy emission is due to interstitial iodide and related Frenkel defects. Our results demonstrate that white-light emission is not limited to ⟨110⟩ oriented bromide 2D perovskites but a general property of this class of system, and highlight the importance of defect control for the formation of low-energy emissive sites, which can provide a pathway to design tailored white-light emitters.

Raffaello Multi-Purpose Logistics Module (MPLM) in Discovery Cargo Bay

NASA Technical Reports Server (NTRS)

2005-01-01

Launched on July 26, 2005 from the Kennedy Space Center in Florida, STS-114 was classified as Logistics Flight 1. Among the Station-related activities of the mission were the delivery of new supplies and the replacement of one of the orbital outpost's Control Moment Gyroscopes (CMGs). STS-114 also carried the Raffaello Multi-Purpose Logistics Module (MPLM) and the External Stowage Platform-2. Back dropped by popcorn-like clouds, the MPLM can be seen in the cargo bay as Discovery undergoes rendezvous and docking operations. Cosmonaut Sergei K. Kriklev, Expedition 11 Commander, and John L. Phillips, NASA Space Station officer and flight engineer photographed the spacecraft from the International Space Station (ISS).

Raffaello Multi-Purpose Logistics Module (MPLM) in Discovery Cargo Bay

NASA Technical Reports Server (NTRS)

2005-01-01

Launched on July 26 2005 from the Kennedy Space Center in Florida, STS-114 was classified as Logistics Flight 1. Among the Station-related activities of the mission were the delivery of new supplies and the replacement of one of the orbital outpost's Control Moment Gyroscopes (CMGs). STS-114 also carried the Raffaello Multi-Purpose Logistics Module (MPLM) and the External Stowage Platform-2. Back dropped by popcorn-like clouds, the MPLM can be seen in the cargo bay as Discovery undergoes rendezvous and docking operations. Cosmonaut Sergei K. Kriklev, Expedition 11 Commander, and John L. Phillips, NASA Space Station officer and flight engineer photographed the spacecraft from the International Space Station (ISS).

Multi-Purpose Logistics Module (MPLM) Cargo Heat Exchanger

NASA Technical Reports Server (NTRS)

Zampiceni, John J.; Harper, Lon T.

2002-01-01

This paper describes the New Shuttle Orbiter's Multi- Purpose Logistics Modulo (MPLM) Cargo Heat Exchanger (HX) and associated MPLM cooling system. This paper presents Heat Exchanger (HX) design and performance characteristics of the system.

KSC-07pd0896

NASA Image and Video Library

2007-04-17

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility, NASA and Japanese Aerospace and Exploration Agency (JAXA) officials welcome the arrival of the Experiment Logistics Module Pressurized Section for the Japanese Experiment Module, or JEM, to the Kennedy Space Center. At the podium is Dr. Kichiro Imagawa, project manager of the JEM Development Project Team for JAXA. Seated at right are Russ Romanella, director of International Space Station and Spacecraft Processing; Bill Parsons, director of Kennedy Space Center; Melanie Saunders, associate manager of the International Space Station Program at Johnson Space Center; and Dominic Gorie, commander on mission STS-123 that will deliver the module to the space station. The logistics module will serve as an on-orbit storage area for materials, tools and supplies. It can hold up to eight experiment racks and will attach to the top of another larger pressurized module. Photo credit: NASA/George Shelton

KSC-07pd2829

NASA Image and Video Library

2007-10-11

KENNEDY SPACE CENTER, FLA. -- In the Space Station Processing Facility at NASA's Kennedy Space Center, STS-123 Mission Specialist Takao Doi (left) and Commander Dominic Gorie confer about the mission payload, the Kibo Experiment Logistics Module Pressurized Section, they are looking over. They are at the center for a crew equipment interface test, which allows familiarization with equipment they will use during the mission. Crew members are Commander Dominic Gorie, Pilot Gregory Johnson and Mission Specialists Richard Linnehan, Takao Doi, Robert Behnken, Gerrett Reisman and Michael Foreman. Doi represents the Japan Aerospace Exploration Agency. Reisman will remain on the space station after the mission as a flight engineer for Expedition 16. STS-123 will carry and install one of the components of the Japanese Experiment Module, or JEM. Known as Kibo, the JEM comprises six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. The various components of JEM will be assembled in space over the course of three space shuttle missions. The first of those three missions, STS-123, will carry the Experiment Logistics Module Pressurized Section aboard the space shuttle Endeavour, targeted for launch in February 2008. Photo credit: NASA/Dimitrios Gerondidakis

KENNEDY SPACE CENTER, FLA. - The U.S. Node 2 is undergoing a Multi-Element Integrated Test (MEIT) in the Space Station Processing Facility. Node 2 attaches to the end of the U.S. Lab on the ISS and provides attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and, eventually, Multipurpose Logistics Modules. It will provide the primary docking location for the Shuttle when a pressurized mating adapter is attached to Node 2. Installation of the module will complete the U.S. Core of the ISS.

NASA Image and Video Library

2003-08-27

KENNEDY SPACE CENTER, FLA. - The U.S. Node 2 is undergoing a Multi-Element Integrated Test (MEIT) in the Space Station Processing Facility. Node 2 attaches to the end of the U.S. Lab on the ISS and provides attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and, eventually, Multipurpose Logistics Modules. It will provide the primary docking location for the Shuttle when a pressurized mating adapter is attached to Node 2. Installation of the module will complete the U.S. Core of the ISS.

The International Space Station's Multi-Purpose Logistics Module, Thermal Performance of the First Five Flights

NASA Technical Reports Server (NTRS)

Holladay, Jon; Cho, Frank

2003-01-01

The Multi-Purpose Logistics Module is the primary carrier for transport of pressurized payload to the International Space Station. Performing five missions within a thirteen month span provided a unique opportunity to gather a great deal of information toward understanding and verifying the orbital performance of the vehicle. This paper will provide a brief overview of the hardware history and design capabilities followed by a summary of the missions flown, resource requirements and possibilities for the future.

KSC-08pd1842

NASA Image and Video Library

2008-06-26

CAPE CANAVERAL, Fla. – In the Space Station Processing Facility at NASA's Kennedy Space Center, STS-126 crew members check out the interior of the multi-purpose logistics module that will fly on the mission. Shuttle crews frequently visit Kennedy to get hands-on experience, called a crew equipment interface test, with hardware and equipment for their missions. On STS-126, Endeavour will deliver a multi-purpose logistics module to the International Space Station. Launch is targeted for Nov. 10. Photo credit: NASA/Kim Shiflett

KSC-02pd1843

NASA Image and Video Library

2002-11-08

KENNEDY SPACE CENTER, FLA. - At the SPACEHAB facility in Cape Canaveral, STS-114 Pilot James Kelly (left), Commander Eileen Collins (center) and a technician participate in familiarization activities on the module that will fly on the STS-114 mission. STS-114 is a utilization and logistics flight that will carry Multi-Purpose Logistics Module Raffaello and the External Stowage Platform (ESP-2), as well as the Expedition 7 crew, to the International Space Station. Launch of STS-114 is currently targeted for March 1, 2003.

Photovoltaic properties of Cu-doped CH3NH3PbI3 with perovskite structure

NASA Astrophysics Data System (ADS)

Shirahata, Yasuhiro; Oku, Takeo

2017-01-01

Photovoltaic properties of copper (Cu)-doped perovskite (CH3NH3PbCuxI3+x) photovoltaic devices with different Cu content were investigated. The CH3NH3PbCuxI3+x films were polycrystalline with a tetragonal system, and their lattice constants and crystallite size varied with Cu doping. Compared to conversion efficiencies of non-doped CH3NH3PbI3 photovoltaic device, those of CH3NH3PbCuxI3+x photovoltaic devises increased. The improvement of photovoltaic properties was attributed to partial substitution of Cu at the Pb sites.

Heterostructured WS2 /CH3 NH3 PbI3 Photoconductors with Suppressed Dark Current and Enhanced Photodetectivity.

PubMed

Ma, Chun; Shi, Yumeng; Hu, Weijin; Chiu, Ming-Hui; Liu, Zhixiong; Bera, Ashok; Li, Feng; Wang, Hong; Li, Lain-Jong; Wu, Tom

2016-05-01

Heterostructured photoconductors based on hybrid perovskites and 2D transition-metal dichalcogenides are fabricated and characterized. Due to the superior properties of CH3 NH3 PbI3 and WS2 , as well as the efficient interfacial charge transfer, such photoconductors show high performance with on/off ratio of ≈10(5) and responsivity of ≈17 A W(-1) . Furthermore, the response times of the heterostructured photoconductors are four orders of magnitude faster compared to the counterpart of a perovskite single layer. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Antiferroelectric Nature of CH3NH3PbI3-xClx Perovskite and Its Implication for Charge Separation in Perovskite Solar Cells

NASA Astrophysics Data System (ADS)

Sewvandi, Galhenage A.; Kodera, Kei; Ma, Hao; Nakanishi, Shunsuke; Feng, Qi

2016-07-01

Perovskite solar cells (PSCs) have been attracted scientific interest due to high performance. Some researchers have suggested anomalous behavior of PSCs to the polarizations due to the ion migration or ferroelectric behavior. Experimental results and theoretical calculations have suggested the possibility of ferroelectricity in organic-inorganic perovskite. However, still no studies have been concretely discarded the ferroelectric nature of perovskite absorbers in PSCs. Hysteresis of P-E (polarization-electric field) loops is an important evidence to confirm the ferroelectricity. In this study, P-E loop measurements, in-depth structural study, analyses of dielectric behavior and the phase transitions of CH3NH3PbI3-xClx perovskite were carried out and investigated. The results suggest that CH3NH3PbI3-xClx perovskite is in an antiferroelectric phase at room temperature. The antiferroelectric phase can be switched to ferroelectric phase by the poling treatment and exhibits ferroelectric-like hysteresis P-E loops and dielectric behavior around room temperature; namely, the perovskite can generate a ferroelectric polarization under PSCs operating conditions. Furthermore, we also discuss the implications of ferroelectric polarization on PSCs charge separation.

Qualification Status of Non-Asbestos Internal Insulation in the Reusable Solid Rocket Motor Program

NASA Technical Reports Server (NTRS)

Clayton, Louie

2011-01-01

This paper provides a status of the qualification efforts associated with NASA's RSRMV non-asbestos internal insulation program. For many years, NASA has been actively engaged in removal of asbestos from the shuttle RSRM motors due to occupation health concerns where technicians are working with an EPA banned material. Careful laboratory and subscale testing has lead to the downselect of a organic fiber known as Polybenzimidazol to replace the asbestos fiber filler in the existing synthetic rubber copolymer Nitrile Butadiene - now named PBI/NBR. Manufacturing, processing, and layup of the new material has been a challenge due to the differences in the baseline shuttle RSRM internal insulator properties and PBI/NBR material properties. For this study, data gathering and reduction procedures for thermal and chemical property characterization for the new candidate material are discussed. Difficulties with test procedures, implementation of properties into the Charring Material Ablator (CMA) codes, and results correlation with static motor fire data are provided. After two successful five segment motor firings using the PBI/NBR insulator, performance results for the new material look good and the material should eventually be qualified for man rated use in large solid rocket motor applications.

Antiferroelectric Nature of CH3NH3PbI3-xClx Perovskite and Its Implication for Charge Separation in Perovskite Solar Cells.

PubMed

Sewvandi, Galhenage A; Kodera, Kei; Ma, Hao; Nakanishi, Shunsuke; Feng, Qi

2016-07-29

Perovskite solar cells (PSCs) have been attracted scientific interest due to high performance. Some researchers have suggested anomalous behavior of PSCs to the polarizations due to the ion migration or ferroelectric behavior. Experimental results and theoretical calculations have suggested the possibility of ferroelectricity in organic-inorganic perovskite. However, still no studies have been concretely discarded the ferroelectric nature of perovskite absorbers in PSCs. Hysteresis of P-E (polarization-electric field) loops is an important evidence to confirm the ferroelectricity. In this study, P-E loop measurements, in-depth structural study, analyses of dielectric behavior and the phase transitions of CH3NH3PbI3-xClx perovskite were carried out and investigated. The results suggest that CH3NH3PbI3-xClx perovskite is in an antiferroelectric phase at room temperature. The antiferroelectric phase can be switched to ferroelectric phase by the poling treatment and exhibits ferroelectric-like hysteresis P-E loops and dielectric behavior around room temperature; namely, the perovskite can generate a ferroelectric polarization under PSCs operating conditions. Furthermore, we also discuss the implications of ferroelectric polarization on PSCs charge separation.

Perovskite Solar Cells with Near 100% Internal Quantum Efficiency Based on Large Single Crystalline Grains and Vertical Bulk Heterojunctions

DOE PAGES

Yang, Bin; Dyck, Ondrej; Poplawsky, Jonathan; ...

2015-07-09

Grain boundaries (GBs) as defects in the crystal lattice detrimentally impact the power conversion efficiency (PCE) of polycrystalline solar cells, particularly in recently emerging hybrid perovskites where non-radiative recombination processes lead to significant carrier losses. Here, the beneficial effects of activated vertical GBs are demonstrated by first growing large, vertically-oriented methylammonium lead tri-iodide (CH 3NH 3PbI 3) single-crystalline grains. We show that infiltration of p-type doped 2 -7,7 -tetrakis(N,Ndi-p-methoxyphenylamine)-9,9-spirobifluorene (Spiro-OMeTAD) into CH 3NH 3PbI 3 films along the GBs creates space charge regions to suppress non-radiative recombination and enhance carrier collection efficiency. Solar cells with such activated GBs yielded averagemore » PCE of 16.3 ± 0.9%, which are among the best solution-processed perovskite devices. As an important alternative to growing ideal CH 3NH 3PbI 3 single crystal films, which is difficult to achieve for such fast-crystallizing perovskites, activating GBs paves a way to design a new type of bulk heterojunction hybrid perovskite photovoltaics toward theoretical maximum PCE.« less

Energy transfer within self-assembled cyclic multichromophoric arrays based on orthogonally arranged donor-acceptor building blocks.

PubMed

Karakostas, Nikolaos; Kaloudi-Chantzea, Antonia; Martinou, Elisabeth; Seintis, Kostas; Pitterl, Florian; Oberacher, Herbert; Fakis, Mihalis; Kallitsis, Joannis K; Pistolis, George

2015-01-01

We herein present the coordination-driven supramolecular synthesis and photophysics of a [4+4] and a [2+2] assembly, built up by alternately collocated donor-acceptor chromophoric building blocks based, respectively, on the boron dipyrromethane (Bodipy) and perylene bisimide dye (PBI). In these multichromophoric scaffolds, the intensely absorbing/emitting dipoles of the Bodipy subunit are, by construction, cyclically arranged at the corners and aligned perpendicular to the plane formed by the closed polygonal chain comprising the PBI units. Steady-state and fs time-resolved spectroscopy reveal the presence of efficient energy transfer from the vertices (Bodipys) to the edges (PBIs) of the polygons. Fast excitation energy hopping - leading to a rapid excited state equilibrium among the low energy perylene-bisimide chromophores - is revealed by fluorescence anisotropy decays. The dynamics of electronic excitation energy hopping between the PBI subunits was approximated on the basis of a theoretical model within the framework of Förster energy transfer theory. All energy-transfer processes are quantitatively describable with Förster theory. The influence of structural deformations and orientational fluctuations of the dipoles in certain kinetic schemes is discussed.

Dynamic Stacking Pathway of Perylene Dimers in Aromatic and Nonaromatic Solvents.

PubMed

Hollfelder, Manuel; Gekle, Stephan

2015-08-13

Using molecular dynamics simulations, we elucidate in detail the dynamics of the π-π stacking process of a perylene bisimide (PBI) dimer solvated in toluene. Our calculations show that the transition from the open (unstacked) to the stacked configuration is hindered by a small free energy barrier of approximately 1kBT in toluene but not in the nonaromatic solvent hexane. A similar effect is observed tor two non-covalently linked monomers. The origin of this barrier is traced back to π-π interactions between perylene and the aromatic solvent which are very similar in nature to those between two PBI monomers. The stacking process proceeds in three phases via two well-defined transition states: (i) in the first phase, the two PBI molecules share part of their respective solvation shells forming the first transition state. Further approach needs to squeeze out the shared solvent layer, thus creating the energy barrier. (ii) After removal of the separating solvent, the two PBIs form a second transition state with one monomer located at a random position in the other's solvation shell. (iii) Finally, the two PBIs slide on top of each other into their final stacked position.

The pure rotational spectra of the open-shell diatomic molecules PbI and SnI

DOE Office of Scientific and Technical Information (OSTI.GOV)

Evans, Corey J., E-mail: cje8@le.ac.uk, E-mail: nick.walker@newcastle.ac.uk; Needham, Lisa-Maria E.; Walker, Nicholas R., E-mail: cje8@le.ac.uk, E-mail: nick.walker@newcastle.ac.uk

2015-12-28

Pure rotational spectra of the ground electronic states of lead monoiodide and tin monoiodide have been measured using a chirped pulsed Fourier transform microwave spectrometer over the 7-18.5 GHz region for the first time. Each of PbI and SnI has a X {sup 2}Π{sub 1/2} ground electronic state and may have a hyperfine structure that aids the determination of the electron electric dipole moment. For each species, pure rotational transitions of a number of different isotopologues and their excited vibrational states have been assigned and fitted. A multi-isotopologue Dunham-type analysis was carried out on both species producing values for Y{submore » 01}, Y{sub 02}, Y{sub 11}, and Y{sub 21}, along with Λ-doubling constants, magnetic hyperfine constants and nuclear quadrupole coupling constants. The Born-Oppenheimer breakdown parameters for Pb have been evaluated and the parameter rationalized in terms of finite nuclear field effects. Analysis of the bond lengths and hyperfine interaction indicates that the bonding in both PbI and SnI is ionic in nature. Equilibrium bond lengths have been evaluated for both species.« less

Investigation of the Interaction between Perovskite Films with Moisture via in Situ Electrical Resistance Measurement.

PubMed

Hu, Long; Shao, Gang; Jiang, Tao; Li, Dengbing; Lv, Xinlin; Wang, Hongya; Liu, Xinsheng; Song, Haisheng; Tang, Jiang; Liu, Huan

2015-11-18

Organometal halide perovskites have recently emerged as outstanding semiconductors for solid-state optoelectronic devices. Their sensitivity to moisture is one of the biggest barriers to commercialization. In order to identify the effect of moisture in the degradation process, here we combined the in situ electrical resistance measurement with time-resolved X-ray diffraction analysis to investigate the interaction of CH3NH3PbI(3-x)Cl(x) perovskite films with moisture. Upon short-time exposure, the resistance of the perovskite films decreased and it could be fully recovered, which were ascribed to a mere chemisorption of water molecules, followed by the reversible hydration into CH3NH3PbI(3-x)Cl(x)·H2O. Upon long-time exposure, however, the resistance became irreversible due to the decomposition into PbI2. The results demonstrated the formation of monohydrated intermediate phase when the perovskites interacted with moisture. The role of moisture in accelerating the thermal degradation at 85 °C was also demonstrated. Furthermore, our study suggested that the perovskite films with fewer defects may be more inherently resistant to moisture.

Coexistence of two electronic nano-phases on a CH 3NH 3PbI 3–xCl x surface observed in STM measurements

DOE PAGES

Yost, Andrew J.; Pimachev, Artem; Ho, Chun -Chih; ...

2016-10-10

Scanning tunneling microscopy is utilized to investigate the local density of states of a CH 3NH 3PbI 3-xCl x perovskite in cross-sectional geometry. Two electronic phases, 10-20 nm in size, with different electronic properties inside the CH 3NH 3PbI 3-xCl x perovskite layer are observed by the dI/ dV mapping and point spectra. A power law dependence of the dI/dV point spectra is revealed. In addition, the distinct electronic phases are found to have preferential orientations close to the normal direction of the film surface. Density functional theory calculations indicate that the observed electronic phases are associated with local deviationmore » of I/Cl ratio, rather than different orientations of the electric dipole moments in the ferroelectric phases. Furthermore, by comparing the calculated results with experimental data we conclude that phase A (lower contrast in dI/dV mapping at -2.0 V bias) contains a lower I/Cl ratio than that in phase B (higher contrast in dI/dV).« less

ZnO nanostructures as electron extraction layers for hybrid perovskite thin films

NASA Astrophysics Data System (ADS)

Nikolaidou, Katerina; Sarang, Som; Tung, Vincent; Lu, Jennifer; Ghosh, Sayantani

Optimum interaction between light harvesting media and electron transport layers is critical for the efficient operation of photovoltaic devices. In this work, ZnO layers of different morphologies are implemented as electron extraction and transport layers for hybrid perovskite CH3NH3PbI3 thin films. These include nanowires, nanoparticles, and single crystalline film. Charge transfer at the ZnO/perovskite interface is investigated and compared through ultra-fast characterization techniques, including temperature and power dependent spectroscopy, and time-resolved photoluminescence. The nanowires cause an enhancement in perovskite emission, which may be attributed to increased scattering and grain boundary formation. However, the ZnO layers with decreasing surface roughness exhibit better electron extraction, as inferred from photoluminescence quenching, reduction in the number of bound excitons, and reduced exciton lifetime in CH3NH3PbI3 samples. This systematic study is expected to provide an understanding of the fundamental processes occurring at the ZnO-CH3NH3PbI3 interface and ultimately, provide guidelines for the ideal configuration of ZnO-based hybrid Perovskite devices. This research was supported by National Aeronautics and Space administration (NASA) Grant No: NNX15AQ01A.

The effect of an oral hygiene program on oral levels of volatile sulfur compounds (VSC).

PubMed

Seemann, R; Passek, G; Zimmer, S; Roulet, J F

2001-01-01

Volatile sulfur compounds (VSCs) produced by bacteria in niches of the oral cavity play a major role in the etiology of bad breath, and can be easily detected by a portable sulfide monitor (Halimeter). To investigate the effect of an oral hygiene program on VSC levels, Halimeter readings were taken from 55 healthy dental students during a course in oral hygiene training, including instruction on brushing, flossing and professional tooth cleaning. Ten students who received no oral hygiene training served as a negative control. The oral hygiene status was measured using the papillary bleeding index (PBI). PBI and VSC values did not show significant changes during the study period of 10 weeks in the control group. In the test group, PBI values significantly decreased compared to baseline and the control, indicating that the oral hygiene program had a benefit on the oral hygiene status. The VSC values also decreased significantly during the study period compared to baseline and the control. It was concluded that in a group of dental students, a thorough oral hygiene training program was capable of reducing the oral level of VSC Halimeter readings.

Transparent and flexible photodetectors based on CH3NH3PbI3 perovskite nanoparticles

NASA Astrophysics Data System (ADS)

Jeon, Young Pyo; Woo, Sung Jun; Kim, Tae Whan

2018-03-01

Transparent and flexible photodetectors (PDs) based on CH3NH3PbI3 perovskite nanoparticles (NPs) were fabricated by using co-evaporation of methyl ammonium iodide and lead iodide. X-ray diffraction patterns and high-resolution transmission electron microscopy images demonstrated the formation of perovskite NPs. The optical transmittance of the perovskite NPs/glass was above 80% over the entire range of visible wavelengths, indicative of high transparency. The PDs based on CH3NH3PbI3 perovskite NPs were sensitive to a broad range of visible light from 450 to 650 nm. The currents in the PDs under exposure to red, green, and blue light-emitting diodes were enhanced to 5, 10, and 20 times that of the PD in the dark, respectively. The rise and the decay times of the PDs were 50 and 120 μs. The current in the perovskite NP PD on a polyethylene terephthalate substrate was enhanced by approximately 69% when the NP PD was exposed to a blue LED emitting at a wavelength of 459 nm. Despite multiple bending, the transparent and flexible PDs based on methyl ammonium iodide and lead iodide NPs showed reproducibility and high stability in performance.

CH3NH3PbI3 perovskites: Ferroelasticity revealed.

PubMed

Strelcov, Evgheni; Dong, Qingfeng; Li, Tao; Chae, Jungseok; Shao, Yuchuan; Deng, Yehao; Gruverman, Alexei; Huang, Jinsong; Centrone, Andrea

2017-04-01

Ferroelectricity has been proposed as a plausible mechanism to explain the high photovoltaic conversion efficiency in organic-inorganic perovskites; however, convincing experimental evidence in support of this hypothesis is still missing. Identifying and distinguishing ferroelectricity from other properties, such as piezoelectricity, ferroelasticity, etc., is typically nontrivial because these phenomena can coexist in many materials. In this work, a combination of microscopic and nanoscale techniques provides solid evidence for the existence of ferroelastic domains in both CH 3 NH 3 PbI 3 polycrystalline films and single crystals in the pristine state and under applied stress. Experiments show that the configuration of CH 3 NH 3 PbI 3 ferroelastic domains in single crystals and polycrystalline films can be controlled with applied stress, suggesting that strain engineering may be used to tune the properties of this material. No evidence of concomitant ferroelectricity was observed. Because grain boundaries have an impact on the long-term stability of organic-inorganic perovskite devices, and because the ferroelastic domain boundaries may differ from regular grain boundaries, the discovery of ferroelasticity provides a new variable to consider in the quest for improving their stability and enabling their widespread adoption.

A Comparative Study of Phosphoric Acid-doped m-PBI Membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perry, Kelly A; More, Karren Leslie; Payzant, E Andrew

2014-01-01

Phosphoric acid (PA)-doped m-polybenzimidazole (PBI) membranes used in high temperature fuel cells and hydrogen pumps were prepared by a conventional imbibing process and a sol-gel fabrication process. A comparative study was conducted to investigate the critical properties of PA doping levels, ionic conductivities, mechanical properties, and molecular ordering. This systematic study found that sol-gel PA-doped m-PBI membranes were able to absorb higher acid doping levels and to achieve higher ionic conductivities than conventionally imbibed membranes when treated in an equivalent manner. Even at similar acid loadings, the sol-gel membranes exhibited higher ionic conductivities. Heat treatment of conventionally imbibed membranes withmore » 29wt% solids caused a significant reduction in mechanical properties; conversely, sol-gel membranes exhibited an enhancement in mechanical properties. From X-ray structural studies and atomistic simulations, both conventionally imbibed and sol-gel membranes exhibited d-spacings of 3.5 and 4.6 , which were tentatively attributed to parallel ring stacking and staggered side-to-side packing, respectively, of the imidazole rings in these aromatic hetercyclic polymers. An anisotropic staggered side-to-side chain packing present in the conventional membranes may be root to the reduction in mechanical properties.« less

Nine-year follow-up of girls with anorexia nervosa and their siblings: retrospective perceptions of parental bonding and the influence of illness on their everyday life.

PubMed

Halvorsen, Inger; Rø, Øyvind; Heyerdahl, Sonja

2013-01-01

Few previous anorexia nervosa (AN) studies include siblings. To investigate if adolescents with AN retrospectively perceived their parents as less caring and more controlling than their siblings, whether perceived parenting was related to psychological problems, and how AN had influenced their everyday lives. Forty-six former patients (mean age 23.1 years) and 21 siblings participated in the study by completing the Parental Bonding Inventory (PBI) and a questionnaire on the influence of AN during the acute phase. Former patients and their siblings had similar PBI results. Better adaptive functioning and lower levels of internalising psychological problems were correlated with higher ratings of parental care in both patients and siblings. Both patients and siblings reported that the illness had created conflict and caused concern, but had also provided valuable experiences. Perceived parenting was associated with psychological problems in young adulthood but not with eating disorders. Our PBI results for both former patients and siblings were quite similar to non-clinical control groups. Health personnel treating adolescent AN should be aware of siblings' perspectives and needs. Copyright © 2012 John Wiley & Sons, Ltd and Eating Disorders Association.

Effects of Annealing Conditions on Mixed Lead Halide Perovskite Solar Cells and Their Thermal Stability Investigation.

PubMed

Yang, Haifeng; Zhang, Jincheng; Zhang, Chunfu; Chang, Jingjing; Lin, Zhenhua; Chen, Dazheng; Xi, He; Hao, Yue

2017-07-21

In this work, efficient mixed organic cation and mixed halide (MA 0.7 FA 0.3 Pb(I 0.9 Br 0.1 )₃) perovskite solar cells are demonstrated by optimizing annealing conditions. AFM, XRD and PL measurements show that there is a better perovskite film quality for the annealing condition at 100 °C for 30 min. The corresponding device exhibits an optimized PCE of 16.76% with V OC of 1.02 V, J SC of 21.55 mA/cm² and FF of 76.27%. More importantly, the mixed lead halide perovskite MA 0.7 FA 0.3 Pb(I 0.9 Br 0.1 )₃ can significantly increase the thermal stability of perovskite film. After being heated at 80 °C for 24 h, the PCE of the MA 0.7 FA 0.3 Pb(I 0.9 Br 0.1 )₃ device still remains at 70.00% of its initial value, which is much better than the control MAPbI₃ device, where only 46.50% of its initial value could be preserved. We also successfully fabricated high-performance flexible mixed lead halide perovskite solar cells based on PEN substrates.

A New Lead Iodide Perovskite based on Large Organic Cation for Solar Cell Application.

PubMed

Ma, Chunqing; Shen, Dong; Lo, Ming Fai; Lee, Chun-Sing

2018-06-06

Methylammonium (CH3NH3+) and formamidinium ((NH2)2CH+) based lead iodide perovskites are currently the two commonly used organic-inorganic lead iodide perovskites for solar cell application. Till now, there is still no alternative organic cations, which can produce perovskites with bandgaps spanning the visible spectrum (i.e. < 1.7 eV) for solar cell application. Here, a new perovskite using large propane-1,3-diammonium cation (n-Pr(NH3)22+) with a chemical structure of (n-Pr(NH3)2)0.5PbI3 is demonstrated. X-ray diffraction (XRD) result shows that the new perovskite exhibits a three-dimensional (3D), tetragonal phase. The bandgap of the new perovskite is ~ 1.6 eV, which is desirable for photovoltaic application. A (n-Pr(NH3)2)0.5PbI3 perovskite solar cell (PSC) yields a power conversion efficiency (PCE) of 5.1%. More importantly, this new perovskite is composed of larger hydrophobic cation that provides a better moisture resistance compared to CH3NH3PbI3 perovskite. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High Performance of Perovskite Solar Cells via Catalytic Treatment in Two-Step Process: The Case of Solvent Engineering.

PubMed

Li, Wenzhe; Fan, Jiandong; Li, Jiangwei; Niu, Guangda; Mai, Yaohua; Wang, Liduo

2016-11-09

Currently, the potential mechanism of the solvent-assisted crystallization for mixed cations perovskite thin film (FA x MA 1-x PbI 3 ) prepared via two-step solution-process still remains obscure. Here, we clarified the molecular-competing-reacted process of NH 2 CH═NH 2 I (FAI) and CH 3 NH 3 I (MAI) with PbI 2 (DMSO) x complex in dimethyl sulfoxide (DMSO) and diethyl ether (DE) catalytic solvent system in the sequential two-step solution-process. The microscopic dynamics was characterized via the characterizations of in situ photoluminescence spectra. In addition, we found that the thermal stability of the perovskite films suffered from the residual solvent with high boiling point, for example, DMSO. The further DE treatment could promote the volatility process of DMSO and accelerate the crystallization process of perovskite films. The highest PCE over 19% with slight hysteresis effect was eventually obtained with a reproducible FA 0.88 MA 0.12 PbI 3 solar cell, which displayed a constant power output within 100 s upon light soaking and stable PCE output within 30 d in the thermal stability test.

Electronic and Morphological Inhomogeneities in Pristine and Deteriorated Perovskite Photovoltaic Films

DOE PAGES

Berweger, Samuel; MacDonald, Gordon A.; Yang, Mengjin; ...

2017-02-02

We perform scanning microwave microscopy (SMM) to study the spatially varying electronic properties and related morphology of pristine and degraded methylammonium lead-halide (MAPI) perovskite films fabricated under different ambient humidity. Here, we find that higher processing humidity leads to the emergence of increased conductivity at the grain boundaries but also correlates with the appearance of resistive grains that contain PbI 2. Deteriorated films show larger and increasingly insulating grain boundaries as well as spatially localized regions of reduced conductivity within grains. These results suggest that while humidity during film fabrication primarily benefits device properties due to the passivation of trapsmore » at the grain boundaries and self-doping, it also results in the emergence of PbI 2-containing grains. We further establish that MAPI film deterioration under ambient conditions proceeds via the spatially localized breakdown of film conductivity, both at grain boundaries and within grains, due to local variations in susceptibility to deterioration. These results confirm that PbI 2 has both beneficial and adverse effects on device performance and provide new means for device optimization by revealing spatial variations in sample conductivity as well as morphological differences in resistance to sample deterioration.« less

The Effects of the Organic-Inorganic Interactions on the Thermal Transport Properties of CH3NH3PbI3.

PubMed

Hata, Tomoyuki; Giorgi, Giacomo; Yamashita, Koichi

2016-04-13

Methylammonium lead iodide perovskite (CH3NH3PbI3), the most investigated hybrid organic-inorganic halide perovskite, is characterized by a quite low thermal conductivity. The rotational motion of methylammonium cations is considered responsible for phonon transport suppression; however, to date, the specific mechanism of the process has not been clarified. In this study, we elucidate the role of rotations in thermal properties based on molecular dynamics simulations. To do it, we developed an empirical potential for CH3NH3PbI3 by fitting to ab initio calculations and evaluated its thermal conductivity by means of nonequilibrium molecular dynamics. Results are compared with model systems that include different embedded cations, and this comparison shows a dominant suppression effect provided by rotational motions. We also checked the temperature dependence of the vibrational density of states and specified the energy range in which anharmonic couplings occur. By means of phonon dispersion analysis, we were able to fully elucidate the suppression mechanism: the rotations are coupled with translational motions of cations, via which inorganic lattice vibrations are coupled and scatter each other.

Low-Pressure Vapor-Assisted Solution Process for Thiocyanate-Based Pseudohalide Perovskite Solar Cells.

PubMed

Chiang, Yu-Hsien; Cheng, Hsin-Min; Li, Ming-Hsien; Guo, Tzung-Fang; Chen, Peter

2016-09-22

In this report, we fabricated thiocyanate-based perovskite solar cells with low-pressure vapor-assisted solution process (LP-VASP) method. Photovoltaic performances are evaluated with detailed materials characterizations. Scanning electron microscopy images show that SCN-based perovskite films fabricated using LP-VASP have long-range uniform morphology and large grain sizes up to 1 μm. The XRD and Raman spectra were employed to observe the characteristic peaks for both SCN-based and pure CH 3 NH 3 PbI 3 perovskite. We observed that the Pb(SCN) 2 film transformed to PbI 2 before the formation of perovskite film. X-ray photoemission spectra (XPS) show that only a small amount of S remained in the film. Using LP-VASP method, we fabricated SCN-based perovskite solar cells and achieved a power conversion efficiency of 12.72 %. It is worth noting that the price of Pb(SCN) 2 is only 4 % of PbI 2 . These results demonstrate that pseudo-halide perovskites are promising materials for fabricating low-cost perovskite solar cells. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

STS-96 crew takes part in payload Interface Verification Test

NASA Technical Reports Server (NTRS)

1999-01-01

Posing on the platform next to the SPACEHAB Logistics Double Module in the SPACEHAB Facility are the STS-96 crew (from left) Mission Specialists Dan Barry, Tamara Jernigan, Valery Tokarev of Russia, and Julie Payette; Pilot Rick Husband; Mission Specialist Ellen Ochoa; and Commander Kent Rominger. The crew is at KSC for a payload Interface Verification Test for their upcoming mission to the International Space Station. Mission STS-96 carries the SPACEHAB Logistics Double Module, which will have equipment to further outfit the International Space Station service module and equipment that can be off-loaded from the early U.S. assembly flights. It carries internal logistics and resupply cargo for station outfitting, plus an external Russian cargo crane to be mounted to the exterior of the Russian station segment and used to perform space walking maintenance activities. The double module stowage provides capacity of up to 10,000 lbs. with the ability to accommodate powered payloads, four external rooftop stowage locations, four double-rack locations (two powered), up to 61 bulkhead-mounted middeck locker locations, and floor storage for large unique items and Soft Stowage. STS-96 is targeted to launch May 20 about 9:32 a.m.

Perceptions of parental bonding in freebase cocaine users versus non-illicit drug users

PubMed Central

Pettenon, Márcia; Kessler, Felix Henrique Paim; Guimarães, Luciano S. P.; Pedroso, Rosemeri Siqueira; Hauck, Simone; Pechansky, Flavio

2014-01-01

Background & objectives: Evidence has suggested that parenting styles have peculiar characteristics in families with drug-related issues. This study was undertaken to investigate the perception of crack (smoke cocaine) users and non-users about parental bonding quality regarding care and control in Brazil. Methods: A total of 198 hospitalized crack users and 104 users of any non-illicit drug were assessed using the Parental Bonding Instrument (PBI), the sixth version of the Addiction Severity Index (ASI) and Mini International Neuropsychiatric Interview (MINI). Results: Adjusted logistic regression analysis showed that crack users were more likely (ORadj = 9.68; 95% CI: 2.82, 33.20) to perceive neglectful mothers, as well as more likely (ORadj = 4.71, 95% CI: 2.17, 10.22) to perceive controlling and affectionless fathers in comparison with non-illicit drug users who were more likely to perceive optimal parenting. Interpretation & conclusions: Our findings indicate that the perception of neglectful mothers and affectionless controlling fathers may be associated with the tendency of the children to be less resilient when facing stressful events, leading them to a greater risk to use crack. PMID:25109717

Logistics Force Planner Assistant (Log Planner)

DTIC Science & Technology

1989-09-01

elements. The system is implemented on a MS-DOS based microcomputer, using the "Knowledge Pro’ software tool., 20 DISTRIBUTION/AVAILABILITY OF... service support structure. 3. A microcomputer-based knowledge system was developed and successfully demonstrated. Four modules of information are...combat service support (CSS) units planning process to Army Staff logistics planners. Personnel newly assigned to logistics planning need an

Logistics resupply and emergency crew return system for Space Station Freedom

NASA Technical Reports Server (NTRS)

Ahne, D.; Caldwell, D.; Davis, K.; Delmedico, S.; Heinen, E.; Ismail, S.; Sumner, C.; Bock, J.; Buente, B.; Gliane, R.

1989-01-01

Sometime in the late 1990's, if all goes according to plan, Space Station Freedom will allow the United States and its cooperating partners to maintain a permanent presence in space. Acting as a scientific base of operations, it will also serve as a way station for future explorations of the Moon and perhaps even Mars. Systems onboard the station will have longer lifetimes, higher reliability, and lower maintenance requirements than seen on any previous space flight vehicle. Accordingly, the station will have to be resupplied with consumables (air, water, food, etc.) and other equipment changeouts (experiments, etc.) on a periodic basis. Waste materials and other products will also be removed from the station for return to Earth. The availability of a Logistics Resupply Module (LRM), akin to the Soviet's Progress vehicle, would help to accomplish these tasks. Riding into orbit on an expendable launch vehicle, the LRM would be configured to rendezvous autonomously and dock with the space station. After the module is emptied of its cargo, waste material from the space station would be loaded back into it. The module would then begin its descent to a recovery point on Earth. Logistics Resupply Modules could be configured in a variety of forms depending on the type of cargo being transferred. If the LRM's were cycled to the space station in such a way that at least one vehicle remained parked at the station at all times, the modules could serve double duty as crew emergency return capsules. A pressurized LRM could then bring two or more crew-persons requiring immediate return (because of health problems, system failure, or unavoidable catastrophes) back to Earth. Large cost savings would be accrued by combining the crew return function with a logistics resupply system.

Power Extension Package (PEP) system definition extension, orbital service module systems analysis study. Volume 7: PEP logistics and training plan requirements

NASA Technical Reports Server (NTRS)

1979-01-01

Recommendations for logistics activities and logistics planning are presented based on the assumption that a system prime contractor will perform logistics functions to support all program hardware and will implement a logistics system to include the planning and provision of products and services to assure cost effective coverage of the following: maintainability; maintenance; spares and supply support; fuels; pressurants and fluids; operations and maintenance documentation training; preservation, packaging and packing; transportation and handling; storage; and logistics management information reporting. The training courses, manpower, materials, and training aids required will be identified and implemented in a training program.

Relationship of order and number of siblings to perceived parental attitudes in childhood.

PubMed

Kitamura, T; Sugawara, M; Shima, S; Toda, M A

1998-06-01

Despite the increasingly recognized link between perceived parenting behavior and the onset of psychopathology in adults, studies of the possible determinants of perceptions of parenting behavior are rare. In a sample of 1,145 pregnant Japanese women, correlations were examined between the numbers and sexes of siblings and perceived rearing practices, as rated by the Parental Bonding Instrument (PBI; Parker, Tupling, & Brown, 1979). The participants with more elder sisters viewed their parents' attitudes as less caring, whereas those with more brothers, particularly younger brothers, viewed their parents' attitudes as less overprotective. However, the proportion of the variance of all the PBI scores explained by different types of siblings was very small.

Boosting the power conversion efficiency of perovskite solar cells using self-organized polymeric hole extraction layers with high work function.

PubMed

Lim, Kyung-Geun; Kim, Hak-Beom; Jeong, Jaeki; Kim, Hobeom; Kim, Jin Young; Lee, Tae-Woo

2014-10-08

A self-organized hole extraction layer (SOHEL) with high work function (WF) is designed for energy level alignment with the ionization potential level of CH3 NH3 PbI3 . The SOHEL increases the built-in potential, photocurrent, and power conversion efficiency (PCE) of CH3 NH3 PbI3 perovskite solar cells. Thus, interface engineering of the positive electrode of solution-processed planar heterojunction solar cells using a high-WF SOHEL is a very effective way to achieve high device efficiency (PCE = 11.7% on glass). © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-114 Mission Specialist Wendy Lawrence manipulates part of a Multi-Purpose Logistics Module. Lawrence is a new addition to the mission crew. The STS-114 crew is at KSC to take part in crew equipment and orbiter familiarization.

NASA Image and Video Library

2003-10-30

KENNEDY SPACE CENTER, FLA. - In the Space Station Processing Facility, STS-114 Mission Specialist Wendy Lawrence manipulates part of a Multi-Purpose Logistics Module. Lawrence is a new addition to the mission crew. The STS-114 crew is at KSC to take part in crew equipment and orbiter familiarization.

Wartime Medical Requirements Models: A Comparison of MPM, MEPES, and LPX-MED.

DTIC Science & Technology

1996-10-01

theater-level models: • Medical Planning Module (MPM) • Medical Planning and Execution System (MEPES) • External Logistics Processor-Medical Module ...current plan is to modify LPX-MED to include a requirements calculator, there is no plan to link the require- ments calculation module and the...simulation module . We believe the simulation module (i.e., today’s LPX-MED) needs reasonable starting values, which a calculator model can pro- vide

Airlock Battery Charge module

NASA Image and Video Library

2008-06-06

S124-E-006858 (6 June 2008) --- Astronauts Greg Chamitoff, Expedition 17 flight engineer, and Karen Nyberg, STS-124 mission specialist, use the controls of the International Space Station's robotic Canadarm2 in the Destiny laboratory to maneuver the Kibo Japanese logistics module from atop the Harmony node to the top of the Kibo Japanese Pressurized Module.

KSC-06pd0924

NASA Image and Video Library

2006-05-23

KENNEDY SPACE CENTER, FLA. -- From inside the payload changeout room on the rotating service structure on Launch Pad 39B, the multi-purpose logistics module Leonardo is being moved into Space Shuttle Discovery's payload bay. The payload ground-handling mechanism (PGHM) is used to transfer the module into the payload bay. Leonardo is a reusable logistics carrier. It is the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Leonardo is part of the payload on mission STS-121. Other payloads include the integrated cargo carrier with the mobile transporter reel assembly and a spare pump module, and the lightweight multi-purpose experiment support structure carrier. Discovery is scheduled to launch in a window extending from July 1 through July 19. Photo credit: NASA/Jack Pfaller

KSC-06pd0927

NASA Image and Video Library

2006-05-23

KENNEDY SPACE CENTER, FLA. -- From inside the payload changeout room on the rotating service structure on Launch Pad 39B, the multi-purpose logistics module Leonardo is lowered into Space Shuttle Discovery's payload bay. The payload ground-handling mechanism (PGHM) is used to transfer the module into the payload bay. Leonardo is a reusable logistics carrier. It is the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Leonardo is part of the payload on mission STS-121. Other payloads include the integrated cargo carrier with the mobile transporter reel assembly and a spare pump module, and the lightweight multi-purpose experiment support structure carrier. Discovery is scheduled to launch in a window extending from July 1 through July 19. Photo credit: NASA/Jack Pfaller

International Space Station (ISS)

NASA Image and Video Library

2001-03-10

This in-orbit close up shows the Italian Space Agency-built multipurpose Logistics Module (MPLM), Leonardo, the primary cargo of the STS-102 mission, resting in the payload bay of the Space Shuttle Orbiter Discovery. The Leonardo MPLM is the first of three such pressurized modules that will serve as the International Space Station's (ISS') moving vans, carrying laboratory racks filled with equipment, experiments, and supplies to and from the Station aboard the Space Shuttle. The cylindrical module is approximately 21-feet long and 15- feet in diameter, weighing almost 4.5 tons. It can carry up to 10 tons of cargo in 16 standard Space Station equipment racks. Of the 16 racks the module can carry, 5 can be furnished with power, data, and fluid to support refrigerators or freezers. In order to function as an attached station module as well as a cargo transport, the logistics module also includes components that provide life support, fire detection and suppression, electrical distribution, and computer functions. The eighth station assembly flight and NASA's 103rd overall flight, STS-102 launched March 8, 2001 for an almost 13 day mission.

Chlorine Incorporation in the CH3NH3PbI3 Perovskite: Small Concentration, Big Effect.

PubMed

Quarti, Claudio; Mosconi, Edoardo; Umari, Paolo; De Angelis, Filippo

2017-01-03

The role of chlorine doping in CH 3 NH 3 PbI 3 represents an important open issue in the use of hybrid perovskites for photovoltaic applications. In particular, even if a positive role of chlorine doping on perovskite film formation and on material morphology has been demonstrated, an inherent positive effect on the electronic and photovoltaic properties cannot be excluded. Here we carried out periodic density functional theory and Car-Parrinello molecular dynamics simulations, going down to ∼1% doping, to investigate the effect of chlorine on CH 3 NH 3 PbI 3 . We found that such a small doping has important effects on the dynamics of the crystalline structure, both with respect to the inorganic framework and with respect to the cation libration motion. Together, we observe a dynamic spatial localization of the valence and conduction states in separated spatial material regions, which takes place in the 10 -1 ps time scale and which could be the key to ease of exciton dissociation and, likely, to small charge recombination in hybrid perovskites. Moreover, such localization is enhanced by chlorine doping, demonstrating an inherent positive role of chlorine doping on the electronic properties of this class of materials.

On dewetting of thin films due to crystallization (crystallization dewetting).

PubMed

Habibi, Mehran; Rahimzadeh, Amin; Eslamian, Morteza

2016-03-01

Drying and crystallization of a thin liquid film of an ionic or a similar solution can cause dewetting in the resulting thin solid film. This paper aims at investigating this type of dewetting, herein termed "crystallization dewetting", using PbI2 dissolved in organic solvents as the model solution. PbI2 solid films are usually used in X-ray detection and lead halide perovskite solar cells. In this work, PbI2 films are fabricated using spin coating and the effect of major parameters influencing the crystallization dewetting, including the type of the solvent, solution concentration, drying temperature, spin speed, as well as imposed vibration on the substrate are studied on dewetting, surface profile and coverage, using confocal scanning laser microscopy. Simplified hydrodynamic governing equations of crystallization in thin films are presented and using a mathematical representation of the process, it is phenomenologically demonstrated that crystallization dewetting occurs due to the absorption and consumption of the solution surrounding a growing crystal. Among the results, it is found that a low spin speed (high thickness), a high solution concentration and a low drying temperature promote crystal growth, and therefore crystallization dewetting. It is also shown that imposed vibration on the substrate can affect the crystal size and crystallization dewetting.

High-temperature passive direct methanol fuel cells operating with concentrated fuels

NASA Astrophysics Data System (ADS)

Zhao, Xuxin; Yuan, Wenxiang; Wu, Qixing; Sun, Hongyuan; Luo, Zhongkuan; Fu, Huide

2015-01-01

Conventionally, passive direct methanol fuel cells (DMFC) are fed with diluted methanol solutions and can hardly be operated at elevated temperatures (>120 °C) because the ionic conductivity of Nafion-type proton exchange membranes depends strongly on water content. Such a system design would limit its energy density and power density in mobile applications. In this communication, a passive vapor feed DMFC capable of operating with concentrated fuels at high temperatures is reported. The passive DMFC proposed in this work consists of a fuel reservoir, a perforated silicone sheet, a vapor chamber, two current collectors and a membrane electrode assembly (MEA) based on a phosphoric acid doped polybenzimidazole (PBI) membrane. The experimental results reveal that the methanol crossover through a PBI membrane is substantially low when compared with the Nafion membranes and the PBI-based passive DMFC can yield a peak power density of 37.2 mW cm-2 and 22.1 mW cm-2 at 180 °C when 16 M methanol solutions and neat methanol are used respectively. In addition, the 132 h discharge test indicates that the performance of this new DMFC is quite stable and no obvious performance degradation is observed after activation, showing its promising applications in portable power sources.

Antiferroelectric Nature of CH3NH3PbI3−xClx Perovskite and Its Implication for Charge Separation in Perovskite Solar Cells

PubMed Central

Sewvandi, Galhenage A.; Kodera, Kei; Ma, Hao; Nakanishi, Shunsuke; Feng, Qi

2016-01-01

Perovskite solar cells (PSCs) have been attracted scientific interest due to high performance. Some researchers have suggested anomalous behavior of PSCs to the polarizations due to the ion migration or ferroelectric behavior. Experimental results and theoretical calculations have suggested the possibility of ferroelectricity in organic-inorganic perovskite. However, still no studies have been concretely discarded the ferroelectric nature of perovskite absorbers in PSCs. Hysteresis of P-E (polarization-electric field) loops is an important evidence to confirm the ferroelectricity. In this study, P-E loop measurements, in-depth structural study, analyses of dielectric behavior and the phase transitions of CH3NH3PbI3−xClx perovskite were carried out and investigated. The results suggest that CH3NH3PbI3−xClx perovskite is in an antiferroelectric phase at room temperature. The antiferroelectric phase can be switched to ferroelectric phase by the poling treatment and exhibits ferroelectric-like hysteresis P-E loops and dielectric behavior around room temperature; namely, the perovskite can generate a ferroelectric polarization under PSCs operating conditions. Furthermore, we also discuss the implications of ferroelectric polarization on PSCs charge separation. PMID:27468802

Localization/delocalization of charges in bay-linked perylene bisimides.

PubMed

Jiang, Wei; Xiao, Chengyi; Hao, Linxiao; Wang, Zhaohui; Ceymann, Harald; Lambert, Christoph; Di Motta, Simone; Negri, Fabrizia

2012-05-29

The copper-mediated Ullmann coupling of 1,7-dibromoperylene bisimides afforded structurally perfect singly-linked perylene bisimide (PBI) arrays, whilst the homo-coupling of 1,12-dibromoperylene bisimides gave doubly-linked and triply-linked diperylene bisimides. The interactions of three bay-linked diperylene bisimides that differed in their linkage (singly, doubly, and triply) were investigated in their neutral and reduced forms (mono-anion to tetra-anion). UV/Vis absorption and fluorescence spectroscopy revealed different degrees of interaction, which was explained by exciton coupling and conjugation effects. The electrochemical properties and spectroelectrochemistry also showed quite-different degrees of PBI interactions in the reduced mixed-valence species, which was apparent by the observation of CT bands. The interpretation of the experimental findings was supported by spin-restricted and -unrestricted DFT and time-dependent TD-DFT calculations with the long-range-corrected CAM-B3LYP functional. Accordingly, the degree of interaction in both the neutral and reduced forms of the bay-linked PBIs was qualitatively in the order doubly linked

Density Functional Studies of Stoichiometric Surfaces of Orthorhombic Hybrid Perovskite CH3NH3PbI3

DOE PAGES

Wang, Yun; Huang, Jingsong; Sumpter, Bobby G.; ...

2014-12-19

Organic/inorganic hybrid perovskite materials are highly attractive for dye-sensitized solar cells as demonstrated by their rapid advances in energy conversion efficiency. In this work, the structures, energetics, and electronic properties for a range of stoichiometric surfaces of the orthorhombic perovskite CH3NH3PbI3 are theoretically studied using density functional theory. Various possible spatially and constitutionally isomeric surfaces are considered by diversifying the spatial orientations and connectivities of surface Pb-I bonds. The comparison of the surface energies for the most stable configurations identified for various surfaces shows that the stabilities of stoichiometric surfaces are mainly dictated by the coordination numbers of surface atoms,more » which are directly correlated with the numbers of broken bonds. Additionally, Coulombic interactions between I anions and organic countercations on the surface also contribute to the stabilization. Electronic properties are compared between the most stable (100) surface and the bulk phase, showing generally similar features except for the lifted band degeneracy and the enhanced bandgap energy for the surface. These studies on the stoichiometric surfaces serve as the first step toward gaining a fundamental understanding of the interfacial properties in the current structural design of perovskite based solar cells, in order to achieve further breakthroughs in solar conversion efficiencies.« less

Is Cu a stable electrode material in hybrid perovskite solar cells for a 30-year lifetime?

DOE PAGES

Zhao, Jingjing; Zheng, Xiaopeng; Deng, Yehao; ...

2016-10-28

One grand challenge for long-lived perovskite solar cells is that the common electrode materials in solar cells, such as silver and aluminum or even gold, strongly react with hybrid perovskites. Here we report the evaluation of the potential of copper (Cu) as the electrode material in perovskite solar cells for long-term stability. In encapsulated devices which limit exposure to oxygen and moisture, Cu in direct contact with CH 3NH 3PbI 3 showed no reaction at laboratory time scales, and is predicted to be stable for almost 170 years at room temperature and over 22 years at the nominal operating cellmore » temperature of 40 °C. No diffusion of Cu into CH 3NH 3PbI 3 has been observed after thermal annealing for over 100 hours at 80 °C, nor does Cu cause charge trap states in direct contact with CH 3NH 3PbI 3 after long-term thermal annealing or illumination. High performance devices with efficiency above 20% with Cu electrode retains 98% of the initial efficiency after 816 hours storage in ambient environment without encapsulation. Finally, the results indicate Cu is a promising low-cost electrode material for perovskite solar cells for long-term operation.« less

Controllable Growth of Perovskite Films by Room-Temperature Air Exposure for Efficient Planar Heterojunction Photovoltaic Cells

DOE PAGES

Yang, Bin; Dyck, Ondrej; Poplawsky, Jonathan; ...

2015-12-01

A two-step-solution-processing approach has been established to grow void-free perovskite films for low-cost and high-performance planar heterojunction photovoltaic devices. We generally applied a high-temperature thermal annealing treatment in order to drive the diffusion of CH 3NH 3I precursor molecules into the compact PbI 2 layer to form perovskite films. But, thermal annealing for extended periods would lead to degraded device performance due to the defects generated by decomposition of perovskite into PbI 2. In this work, we explored a controllable layer-by-layer spin-coating method to grow bilayer CH 3NH 3I/PbI 2 films, and then drive the interdiffusion between PbI 2 andmore » CH 3NH 3I layers by a simple room-temperature-air-exposure for making well-oriented, highly-crystalline perovskite films without thermal annealing. This high degree of crystallinity resulted in a carrier diffusion length of ~ 800 nm and high device efficiency of 15.6%, which is comparable to the reported values from thermally-annealed perovskite films based counterparts. Finally, the simplicity and high device performance of this processing approach is highly promising for direct integration into industrial-scale device manufacture.« less

Formation Dynamics of CH3NH3PbI3 Perovskite Following Two-Step Layer Deposition.

PubMed

Patel, Jay B; Milot, Rebecca L; Wright, Adam D; Herz, Laura M; Johnston, Michael B

2016-01-07

Hybrid metal-halide perovskites have emerged as a leading class of semiconductors for optoelectronic devices because of their desirable material properties and versatile fabrication methods. However, little is known about the chemical transformations that occur in the initial stages of perovskite crystal formation. Here we follow the real-time formation dynamics of MAPbI3 from a bilayer of lead iodide (PbI2) and methylammonium iodide (MAI) deposited through a two-step thermal evaporation process. By lowering the substrate temperature during deposition, we are able to initially inhibit intermixing of the two layers. We subsequently use infrared and visible light transmission, X-ray diffraction, and photoluminescence lifetime measurements to reveal the room-temperature transformations that occur in vacuum and ambient air, as MAI diffuses into the PbI2 lattice to form MAPbI3. In vacuum, the transformation to MAPbI3 is incomplete as unreacted MAI is retained in the film. However, exposure to moist air allows for conversion of the unreacted MAI to MAPbI3, demonstrating that moisture is essential in making MAI more mobile and thus aiding perovskite crystallization. These dynamic processes are reflected in the observed charge-carrier lifetimes, which strongly fluctuate during periods of large ion migration but steadily increase with improving crystallinity.

Effect of Green Tea Mouthwash on Oral Malodor

PubMed Central

Rassameemasmaung, Supanee; Phusudsawang, Pakkarada; Sangalungkarn, Vanida

2013-01-01

This study aimed to determine the effect of green tea mouthwash on oral malodor, plaque, and gingival inflammation. Gingivitis subjects who had over 80 parts per billion of volatile sulfur compounds (VSC) in the morning breath were randomly assigned into green tea or placebo mouthwash group. At baseline, VSC, Plaque Index (PI) and Papillary Bleeding Index (PBI) were recorded. Participants were rinsed with the assigned mouthwash, and VSC level was remeasured at 30 minutes and 3 hours postrinsing. For the following 4 weeks, participants were asked to rinse with the assigned mouthwash twice daily. VSC, PI and PBI were remeasured at day 28. It was found that, at 30 minutes and 3 hours postrinsing, VSC was reduced by 36.76% and 33.18% in the green tea group and 19.83% and 9.17% in the placebo group, respectively. At day 28, VSC was reduced by 38.61% in the green tea group and 10.86% in the placebo group. VSC level in the green tea group was significantly different when compared to the placebo. PI and PBI were significantly reduced in both groups. However, no significant difference was found between groups. In conclusion, green tea mouthwash could significantly reduce VSC level in gingivitis subjects after rinsing for 4 weeks. PMID:24977093

Effect of green tea mouthwash on oral malodor.

PubMed

Rassameemasmaung, Supanee; Phusudsawang, Pakkarada; Sangalungkarn, Vanida

2013-01-01

This study aimed to determine the effect of green tea mouthwash on oral malodor, plaque, and gingival inflammation. Gingivitis subjects who had over 80 parts per billion of volatile sulfur compounds (VSC) in the morning breath were randomly assigned into green tea or placebo mouthwash group. At baseline, VSC, Plaque Index (PI) and Papillary Bleeding Index (PBI) were recorded. Participants were rinsed with the assigned mouthwash, and VSC level was remeasured at 30 minutes and 3 hours postrinsing. For the following 4 weeks, participants were asked to rinse with the assigned mouthwash twice daily. VSC, PI and PBI were remeasured at day 28. It was found that, at 30 minutes and 3 hours postrinsing, VSC was reduced by 36.76% and 33.18% in the green tea group and 19.83% and 9.17% in the placebo group, respectively. At day 28, VSC was reduced by 38.61% in the green tea group and 10.86% in the placebo group. VSC level in the green tea group was significantly different when compared to the placebo. PI and PBI were significantly reduced in both groups. However, no significant difference was found between groups. In conclusion, green tea mouthwash could significantly reduce VSC level in gingivitis subjects after rinsing for 4 weeks.

Impact of Linear Alkyl Length on the Assembly of Twisted Perylene Bisimides: From Molecular Arrangement to Nanostructures.

PubMed

Guo, Zongxia; Wang, Kun; Yu, Ping; Wang, Xiangnan; Lan, Shusha; Sun, Kai; Yi, Yuanping; Li, Zhibo

2017-11-02

The effect of the length of linear alkyl chains substituted at imine positions on the assembly of tetrachlorinated perylene bisimides (1: PBI with -C 6 H 13 ; 2: PBI with -C 12 H 25 ) has been investigated. Solvent-induced assembly was performed in solutions of THF and methanol with varying volume ratios. Morphological (SEM, AFM, and TEM) and spectral (UV/Vis, fluorescence, FTIR, and XRD) methods were used to characterize the assembled nanostructures and the molecular arrangement in the aggregates. It was found that uniform structures could be obtained for both molecules in solutions with a high ratio of methanol. PBI 1 formed rigid nanosheets, whereas 2 assembled into longer nanostripes with a high ratio of length to width. On combining the morphological data with the spectral data, it was suggested that π-π stacking predominated in assemblies of 1, and the synergetic effect of van der Waals interactions from the long alkyl chains and π-π stacking between neighboring building blocks facilitated the growth of the long-range-ordered nanostructures of 2. By changing the linear chain length, the hierarchical assembly of PBIs modified on bay positions could be manipulated effectively. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

The effect of moisture on the structures and properties of lead halide perovskites: a first-principles theoretical investigation.

PubMed

Zhang, Lei; Ju, Ming-Gang; Liang, WanZhen

2016-08-17

With efficiencies exceeding 20% and low production costs, lead halide perovskite solar cells (PSCs) have become potential candidates for future commercial applications. However, there are serious concerns about their long-term stability and environmental friendliness, heavily related to their commercial viability. Herein, we present a theoretical investigation based on the ab initio molecular dynamics (AIMD) simulations and the first-principles density functional theory (DFT) calculations to investigate the effects of sunlight and moisture on the structures and properties of MAPbI3 perovskites. AIMD simulations have been performed to simulate the impact of a few water molecules on the structures of MAPbI3 surfaces terminated in three different ways. The evolution of geometric and electronic structures as well as the absorption spectra has been shown. It is found that the PbI2-terminated surface is the most stable while both the MAI-terminated and PbI2-defective surfaces undergo structural reconstruction, leading to the formation of hydrated compounds in a humid environment. The moisture-induced weakening of photoabsorption is closely related to the formation of hydrated species, and the hydrated crystals MAPbI3·H2O and MA4PbI6·2H2O scarcely absorb the visible light. The electronic excitation in the bare and water-absorbed MAPbI3 nanoparticles tends to weaken Pb-I bonds, especially those around water molecules, and the maximal decrease of photoexcitation-induced bond order can reach up to 20% in the excited state in which the water molecules are involved in the electronic excitation, indicating the accelerated decomposition of perovskites in the presence of sunlight and moisture. This work is valuable for understanding the mechanism of chemical or photochemical instability of MAPbI3 perovskites in the presence of moisture.

Enhanced Crystalline Phase Purity of CH3NH3PbI3-xClx Film for High-Efficiency Hysteresis-Free Perovskite Solar Cells.

PubMed

Yang, Yingguo; Feng, Shanglei; Xu, Weidong; Li, Meng; Li, Li; Zhang, Xingmin; Ji, Gengwu; Zhang, Xiaonan; Wang, Zhaokui; Xiong, Yimin; Cao, Liang; Sun, Baoquan; Gao, Xingyu

2017-07-12

Despite rapid successful developments toward promising perovskite solar cells (PSCs) efficiency, they often suffer significant hysteresis effects. Using synchrotron-based grazing incidence X-ray diffraction (GIXRD) with different probing depths by varying the incident angle, we found that the perovskite films consist of dual phases with a parent phase dominant in the interior and a child phase with a smaller (110) interplanar space (d (110) ) after rapid thermal annealing (RTA), which is a widely used post treatment to improve the crystallization of solution-processed perovskite films for high-performance planar PSCs. In particular, the child phase composition gradually increases with decreasing depth till it becomes the majority on the surface, which might be one of the key factors related to hysteresis in fabricated PSCs. We further improve the crystalline phase purity of the solution-processed CH 3 NH 3 PbI 3-x Cl x perovskite film (referred as g-perovskite) by using a facile gradient thermal annealing (GTA), which shows a uniformly distributed phase structure in pinhole-free morphology with less undercoordinated Pb and I ions determined by synchrotron-based GIXRD, grazing incidence small-angle X-ray scattering, scanning electron microscopy, and X-ray photoelectron spectroscopy. Regardless of device structures (conventional and inverted types), the planar heterojunction PSCs employing CH 3 NH 3 PbI 3-x Cl x g-perovskite films exhibit negligible hysteresis with a champion power conversion efficiency of 17.04% for TiO 2 -based conventional planar PSCs and 14.83% for poly(3,4-ethylenedioxythiophene:poly(styrenesulfonate) (PEDOT:PSS)-based inverted planar PSCs. Our results indicate that the crystalline phase purity in CH 3 NH 3 PbI 3-x Cl x perovskite film, especially in the surface region, plays a crucial role in determining the hysteresis effect and device performance.

Measuring the importance of health domains in psoriasis - discrete choice experiment versus rating scales.

PubMed

Gutknecht, Mandy; Schaarschmidt, Marthe-Lisa; Danner, Marion; Blome, Christine; Augustin, Matthias

2018-01-01

Psoriasis affects different aspects of health-related quality of life (eg, physical, psychological, and social impairments); these health domains can be of different importance for patients. The importance of domains can be measured with the Patient Benefit Index (PBI). This questionnaire weights the achievement of treatment goals by Likert scales (0, "not important at all" to 4, "very important") using the Patient Needs Questionnaire (PNQ). Treatment goals assessed with the PBI have been assigned to five health domains; the importance of each domain can be calculated as the average importance of the respective treatment goals. In this study, the PBI approach of deriving importance weights is contrasted to a discrete choice experiment (DCE), in order to determine the importance of health domains in psoriasis, and to find if the resulting weights will differ when derived from these two methods. Adult patients with psoriasis completed both questionnaires (PNQ, DCE). The PBI domains were used as attributes in the DCE with the levels "did not help at all", "helped moderately", and "helped a lot". Using DCE, "improving physical functioning" was the most important health domain, followed by "improving psychological well-being". Using PNQ, these domains were ranked in position two and three following "strengthening confidence in the therapy and in a possible healing". The latter was least important using DCE. The only agreement of ranking was shown in "reducing impairments due to therapy" (position four). "Improving social functioning" was ranked in position three (DCE) and five (PNQ). Health domains have different importance to patients with psoriasis. Using PNQ or DCE to determine the importance of domains results in markedly different rankings; both approaches can thus not be considered equivalent. However, in this study, importance was assessed at the domain level in DCE and at the single item level in PNQ, which may have added to the differences.

Two-types of Early Cretaceous adakitic porphyries from the Luxi terrane, eastern North China Block: Melting of subducted Paleo-Pacific slab and delaminated newly underplated lower crust

NASA Astrophysics Data System (ADS)

Wang, Hao; Xu, Zhaowen; Lu, Xiancai; Fu, Bin; Lu, Jianjun; Yang, Xiaonan; Zhao, Zengxia

2016-01-01

The origin and tectonic setting of Early Cretaceous adakitic rocks from the Luxi terrane in the eastern North China Block (NCB) remain debated. To resolve this issue, we determined whole-rock geochemistry, zircon U-Pb ages, and in situ Hf-O isotopes of the Mengyin and Liujing adakitic porphyries from the Luxi terrane. Zircon U-Pb dating results reveal that both the Mengyin and Liujing plutons were emplaced during the Early Cretaceous, with weighted mean 206Pb/238U ages of 130 ± 1 Ma (2σ) and 131 ± 2 Ma (2σ), respectively. In addition, abundant Neoarchean-Paleoproterozoic inherited zircon cores are identified in the Mengyin adakitic porphyry with 207Pb/206Pb ages ranging from 2.53 to 2.42 Ga. Rocks of both plutons are silicic (SiO2 = 65.4-70.2 wt.%), metaluminous, and alkaline in composition, comprising mainly quartz syenite porphyries. Samples from both plutons are enriched in large ion lithophile elements (LILEs) (e.g., Rb, Sr, and Ba), and light rare earth elements (LREEs), depleted in high field strength elements (HFSEs) (e.g., Nb, Ta, and Ti), and heavy rare earth elements (HREEs), and have either positive or no Eu anomalies. In addition, both adakitic porphyries have high Mg# values (51-64), high Sr and La contents, low Y and Yb contents, and high Sr/Y (Mengyin = 149-264; Liujing = 58-110) and (La/Yb)N (Mengyin = 32.4-45.3; Liujing = 43.8-53.1) ratios, similar to adakitic rocks worldwide. The Mengyin adakitic porphyry has higher whole-rock εNd(t) values (-5.8 to - 4.1), more radiogenic Pb [(206Pb/204Pb)i = 18.35-18.39, (207Pb/204Pb)i = 15.55-15.56, (208Pb/204Pb)i = 38.20-38.23], higher zircon rim εHf(t) values (+ 3.3 to + 8.8) and δ18O values (+ 6.5‰ to + 7.9‰), and lower (87Sr/86Sr)i ratios (0.7049-0.7050) than the Liujing adakitic porphyry [εNd(t) = - 12.4 to - 12.2, (206Pb/204Pb)i = 17.63-17.72, (207Pb/204Pb)i = 15.56-15.58, (208Pb/204Pb)i = 37.76-37.94, εHf(t) = - 14.8 to - 11.2, δ18O = + 5.9‰ to + 7.1‰, (87Sr/86Sr)i = 0.7090-0.7091]. The Mengyin adakitic porphyry was most likely derived from partial melting of subducted oceanic slab with some input of NCB Neoarchean-Paleoproterozoic lower crust components. The Liujing adakitic porphyry was probably derived from partial melting of delaminated newly underplated thick lower crust, which then interacted with above asthenospheric mantle peridotite. Slab rollback together with the ridge subduction of the Paleo-Pacific slab was the most likely geodynamic mechanism for formation of the Early Cretaceous Mengyin and Liujing adakitic porphyries.

Geochemical and Isotopic Features of Çaykara (Trabzon, NE Turkey) Intrusive Complex

NASA Astrophysics Data System (ADS)

Sen, Cuneyt; Aydınçakır, Emre; Aydin, Faruk; Dokuz, Abdurrahman; Karslı, Orhan; Yılmazer, Sinan; Dündar, Buket

2017-04-01

Çaykara (Trabzon) Intrusive Complex is located at the eastern part of the Kaçkar Batholith. In the complex, Gündoǧdu-Boǧalı Plutons is Upper Cretaceous in aged, and Uzundere and Eǧerler Plutons are Eocene in aged. Gündoǧdu-Boǧa Plutons crop out around Araklı-Bahçecik villages, and are represented by the granitic to granodioritic rocks in composition showing porphyritic-granular texture. These rocks contain dark coloured, semi-rounded to rounded, wedged, fine-grained diorite and monzodiorite anclaves. Uzuntarla Pluton extends at E-W from Köknar-Karaçam-Uzuntarla sub-districs to south of Çaykara towards Bahçecik sub-district of Araklı. The rocks of the Uzuntarla Pluton are generally diorite to granodiorite in composition with porphyritic in texture. Eǧerler Pluton exposes at southern of the Çaykara Intrusive Complex. It's mineralogical composition is changing from diorite to granite with medium-coarse grain granular texture. The Upper Cretaceous plutonic rocks are characterized by ɛNd(i) values range from -1.5 to -9.7, whereas 87Sr/86Sr(i) values range from 0.7052 to 0.7119. Nd model ages are between 0.94 and 1.52 Ga. 206Pb/204Pb(i), 207Pb/204Pb(i) and 208Pb/204Pb(i) contents of samples change from 18.24 to 18.72, 15.59 to 15.66 and 37.93-38.64, respectively. The δ18O values in the investigated samples range from 4.0 ‰ to 6.7 ‰ and have similar ratios to I-type granitoides.The Eocene plutonic rocks are characterized by ɛNd(i) values range from -0.4 to -6.0, whereas 87Sr/86Sr(i) values range from 0.7050 to 0.7143. Nd model ages are between 0.81 and 1.32 Ga. 206Pb/204Pb(i), 207Pb/204Pb(i) and 208Pb/204Pb(i) contents of samples change from 18.241to 18.57, 15.58 to 15.63 and 38.22-38.92, respectively. The δ18O values in the investigated samples range from 5.8 ‰ to 7.1 ‰ and have similar ratios to I-type granitoides. Upper Cretaceous and Eocene aged Plutons in the study area are high-K calc-alkaline in composition and display metaluminous to peraluminous characteristics. The primitive mantle normalized multi-element variation diagrams of the studied samples show enrichment in LILE relative to HFSE and also negative Nb, Ta, P, Ti and positive Pb anomalies. Chondrite-normalized rare earth element (REE) patterns are [(La/Lu)N=8-10] and display negative Eu anomalies. When obtained initial data is plotted on tectonic discrimination diagram, as expected the tectonic setting of the plutons in subject was observed representing island arc environment. This work was supported by the Scientific and Technological Research Council of Turkey (TUBITAK, grant 114Y219).

Rack Insertion End Effector (RIEE) guidance

NASA Technical Reports Server (NTRS)

Malladi, Narasimha S.

1994-01-01

NASA-KSC has developed a mechanism to handle and insert Racks into the Space Station Logistic Modules. This mechanism consists of a Base with 3 motorized degrees of freedom, a 3 section motorized Boom that goes from 15 to 44 feet in length, and a Rack Insertion End Effector (RIEE) with 5 hand wheels for precise alignment. During the 1993 NASA-ASEE Summer Faculty Fellowship Program at KSC, I designed an Active Vision (Camera) Arrangement and developed an algorithm to determine (1) the displacements required by the Room for its initial positioning and (2) the rotations required at the five hand-wheels of the RIEE, for the insertion of the Rack, using the centroids fo the Camera Images of the Location Targets in the Logistic Module. Presently, during the summer of '94, I completed the preliminary design of an easily portable measuring instrument using encoders to obtain the 3-Dimensional Coordinates of Location Targets in the Logistics Module relative to the RIEE mechanism frame. The algorithm developed in '93 can use the output of this instrument also. Simplification of the '93 work and suggestions for the future work are discussed.

KENNEDY SPACE CENTER, FLA. - Members of the STS-114 crew take a look at the Japanese Experiment Module (JEM) pressure module in the Space Station Processing Facility. A research laboratory, the pressurized module is the first element of the JEM, named "Kibo" (Hope), to be delivered to KSC. The National Space Development Agency of Japan (NASDA) developed the laboratory at the Tsukuba Space Center near Tokyo and is Japan's primary contribution to the Station. The JEM also includes an exposed facility (platform) for space environment experiments, a robotic manipulator system, and two logistics modules. The various JEM components will be assembled in space over the course of three Shuttle missions.

NASA Image and Video Library

2003-06-09

KENNEDY SPACE CENTER, FLA. - Members of the STS-114 crew take a look at the Japanese Experiment Module (JEM) pressure module in the Space Station Processing Facility. A research laboratory, the pressurized module is the first element of the JEM, named "Kibo" (Hope), to be delivered to KSC. The National Space Development Agency of Japan (NASDA) developed the laboratory at the Tsukuba Space Center near Tokyo and is Japan's primary contribution to the Station. The JEM also includes an exposed facility (platform) for space environment experiments, a robotic manipulator system, and two logistics modules. The various JEM components will be assembled in space over the course of three Shuttle missions.

Four-wave mixing response of solution-processed CH3NH3PbI3 thin films

NASA Astrophysics Data System (ADS)

March, Samuel A.; Riley, Drew B.; Clegg, Charlotte; Webber, Daniel; Todd, Seth; Hill, Ian G.; Hall, Kimberley C.

2017-02-01

The interest in perovskite-based solar cell absorber materials has skyrocketed in recent years due to the rapid rise in solar cell efficiency and the potential for cost reductions tied to solution-processed device fabrication. Due to complications associated with the presence of strong static and dynamic disorder in these organic-inorganic materials, the fundamental photophysical behavior of photo-excited charge carriers remains unclear. We apply four-wave mixing spectroscopy to study the charge carrier dynamics in CH3NH3PbI3 thin films. Our experiments reveal two discrete optical transitions below the band gap of the semiconductor with binding energies of 13 meV and 29 meV, attributed to free and defect-bound excitons respectively.

First principles study on mixed orthorhombic perovskite CH3NH3 Pb(I1-xBrx) 3

NASA Astrophysics Data System (ADS)

Fang, Zhou; Yi, Zhijun

2017-11-01

Chemically tuned inorganic-organic hybrid halide perovskites based on iodine and bromine halide anions have been studied using first-principles calculations. Firstly, our results show that the volume of CH3NH3 Pb(I1-xBrx) 3 decreases linearly with the concentration of Br ions, and the band gap can be tuned from 1.9 eV to 2.3 eV by substituting I with Br, resulting in the shift of absorption onset from 650 nm (1.9 eV) to 540 nm (2.3 eV). Secondly, our calculations show that the color of crystal can be tuned from wine to yellow by substituting I with Br.

Anorexia nervosa and parental bonding: the contribution of parent-grandparent relationships to eating disorder psychopathology.

PubMed

Canetti, Laura; Kanyas, Kyra; Lerer, Bernard; Latzer, Yael; Bachar, Eytan

2008-06-01

The present study adopted an intergenerational approach in examining the association between parental bonding and anorexia nervosa. Forty-three anorexic participants and 33 nonclinical comparison participants completed eating disorder questionnaires and the Parental Bonding Instrument (PBI). The participant's parents also completed the PBI. The anorexic participants perceived both parents as less caring and fathers as more controlling than nonclinical participants. Among anorexic participants, mother control and father care were associated with symptom severity. Intergenerational effects were present. Among anorexic participants, maternal grandmother care was associated with eating disorder psychopathology. The present findings suggest that parental characteristics of grandparents might play a role in the development of eating disorders in granddaughters. (c) 2008 Wiley Periodicals, Inc.

Fundamental x-ray interaction limits in diagnostic imaging detectors: frequency-dependent Swank noise.

PubMed

Hajdok, G; Battista, J J; Cunningham, I A

2008-07-01

A frequency-dependent x-ray Swank factor based on the "x-ray interaction" modulation transfer function and normalized noise power spectrum is determined from a Monte Carlo analysis. This factor was calculated in four converter materials: amorphous silicon (a-Si), amorphous selenium (a-Se), cesium iodide (CsI), and lead iodide (PbI2) for incident photon energies between 10 and 150 keV and various converter thicknesses. When scaled by the quantum efficiency, the x-ray Swank factor describes the best possible detective quantum efficiency (DQE) a detector can have. As such, this x-ray interaction DQE provides a target performance benchmark. It is expressed as a function of (Fourier-based) spatial frequency and takes into consideration signal and noise correlations introduced by reabsorption of Compton scatter and photoelectric characteristic emissions. It is shown that the x-ray Swank factor is largely insensitive to converter thickness for quantum efficiency values greater than 0.5. Thus, while most of the tabulated values correspond to thick converters with a quantum efficiency of 0.99, they are appropriate to use for many detectors in current use. A simple expression for the x-ray interaction DQE of digital detectors (including noise aliasing) is derived in terms of the quantum efficiency, x-ray Swank factor, detector element size, and fill factor. Good agreement is shown with DQE curves published by other investigators for each converter material, and the conditions required to achieve this ideal performance are discussed. For high-resolution imaging applications, the x-ray Swank factor indicates: (i) a-Si should only be used at low-energy (e.g., mammography); (ii) a-Se has the most promise for any application below 100 keV; and (iii) while quantum efficiency may be increased at energies just above the K edge in CsI and PbI2, this benefit is offset by a substantial drop in the x-ray Swank factor, particularly at high spatial frequencies.

Holistic Approach to Secondary Earth Science Teacher Professional Development: the Triad of Project-based Instruction, Earth Science Content, and GIS Technology

NASA Astrophysics Data System (ADS)

Rubino-Hare, L.; Sample, J. C.; Fredrickson, K.; Claesgens, J.; Bloom, N.; Henderson-Dahms, C.; Manone, M.

2011-12-01

We have provided two years of professional development for secondary and middle school teachers with a focus on project-based instruction (PBI) using GIS. The EYE-POD project (funded by NSF-ITEST) involved pairs of teachers from Arizona and the surrounding region in two-week institutes during Summer, 2010, and an advanced institute in Summer, 2011. The NAz-POD project (funded by Arizona Department of Education and administered by Science Foundation Arizona) provided similar PD experiences, but the institutes occurred during weekends in the academic year. The institutes were led by a team with expertise in Earth science content, professional development and pedagogy, and GIS. The teachers developed learning modules using the project based learning instructional model. Pedagogy, content, and GIS skills were combined throughout the professional development activities. Academic year follow up by NAU personnel included classroom observations and technical support. For assessing student work we provided a rubric, but learned that teachers were not prepared to assess GIS products in order to determine the level of student understanding. In year two of the project we incorporated strategies for assessment of student products into the professional development. Teacher-participants and their students completed several pre- and post- assessments. Teacher assessments included a geospatial performance assessment, classroom observations, and content tests. Student data collection included attitude and efficacy questionnaires, content tests, and authentic assessments including products using GIS. Content tests were the same for teachers and students and included spatial reasoning, data analysis, and Earth science content. Data was also collected on teacher perception of professional development delivery and self-reported confidence in teaching with PBI and geospatial technology. Student assessments show that improvement occurred in all areas on the content test. Possible factors resulting in this improvement will be shared, and placed in the context of other assessment results.

KSC-06pd0926

NASA Image and Video Library

2006-05-23

KENNEDY SPACE CENTER, FLA. -- From inside the payload changeout room on the rotating service structure on Launch Pad 39B, workers maneuver the multi-purpose logistics module Leonardo into Space Shuttle Discovery's payload bay (at left). The payload ground-handling mechanism (PGHM) is used to transfer the module into the payload bay. Leonardo is a reusable logistics carrier. It is the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Leonardo is part of the payload on mission STS-121. Other payloads include the integrated cargo carrier with the mobile transporter reel assembly and a spare pump module, and the lightweight multi-purpose experiment support structure carrier. Discovery is scheduled to launch in a window extending from July 1 through July 19. Photo credit: NASA/Jack Pfaller

KSC-06pd0925

NASA Image and Video Library

2006-05-23

KENNEDY SPACE CENTER, FLA. -- From inside the payload changeout room on the rotating service structure on Launch Pad 39B, the multi-purpose logistics module Leonardo is being moved into Space Shuttle Discovery's payload bay (at left). The payload ground-handling mechanism (PGHM) is used to transfer the module into the payload bay. Leonardo is a reusable logistics carrier. It is the primary delivery system used to resupply and return station cargo requiring a pressurized environment. Leonardo is part of the payload on mission STS-121. Other payloads include the integrated cargo carrier with the mobile transporter reel assembly and a spare pump module, and the lightweight multi-purpose experiment support structure carrier. Discovery is scheduled to launch in a window extending from July 1 through July 19. Photo credit: NASA/Jack Pfaller

International Space Station (ISS)

NASA Image and Video Library

2001-03-01

A crewmember of Expedition One, cosmonaut Yuri P. Gidzenko, is dwarfed by transient hardware aboard Leonardo, the Italian Space Agency-built Multi-Purpose Logistics Module (MPLM), a primary cargo of the STS-102 mission. The Leonardo MPLM is the first of three such pressurized modules that will serve as the International Space Station's (ISS's) moving vans, carrying laboratory racks filled with equipment, experiments and supplies to and from the Space Station aboard the Space Shuttle. The cylindrical module is approximately 21-feet long and 15- feet in diameter, weighing almost 4.5 tons. It can carry up to 10 tons of cargo into 16 standard Space Station equipment racks. Of the 16 racks the module can carry, 5 can be furnished with power, data, and fluid to support refrigerators or freezers. In order to function as an attached station module as well as a cargo transport, the logistics module also includes components that provide life support, fire detection and suppression, electrical distribution, and computer functions. The eighth Shuttle mission to visit the ISS, the STS-102 mission served as a crew rotation flight. It delivered the Expedition Two crew to the Station and returned the Expedition One crew back to Earth.

KSC-03PD-2142

NASA Technical Reports Server (NTRS)

2003-01-01

KENNEDY SPACE CENTER, FLA. In the Space Station Processing Facility, STS-120 Mission Specialists Michael Foreman (third from right) and STS-115 Mission Specialists Joseph Tanner (second from right) and Heidemarie Stefanyshyn-Piper (right) look over the Japanese Experiment Module (JEM) Pressurized Module. Known as Kibo, the JEM consists of six components: two research facilities -- the Pressurized Module and Exposed Facility; a Logistics Module attached to each of them; a Remote Manipulator System; and an Inter-Orbit Communication System unit. Kibo also has a scientific airlock through which experiments are transferred and exposed to the external environment of space. The various components of JEM will be assembled in space over the course of three Space Shuttle missions. STS-115 will deliver the second port truss segment, the P3/P4 Truss, to attach to the first port truss segment, the P1 Truss, as well as deploy solar array sets 2A and 4A.. STS-120 will deliver the second of three Station connecting modules, Node 2, which attaches to the end of U.S. Lab. It will provide attach locations for the Japanese laboratory, European laboratory, the Centrifuge Accommodation Module and later Multi-Purpose Logistics Modules. The addition of Node 2 will complete the U.S. core of the International Space Station.

Scaling behavior of moisture-induced grain degradation in polycrystalline hybrid perovskite thin films

DOE PAGES

Wang, Qi; Chen, Bo; Liu, Ye; ...

2017-01-01

The stability of perovskite solar cells has shown a huge variation with respect to the film process and film morphology, while the underlining mechanism for the morphology-dependent degradation of the perovskite film has remained elusive. Herein, we report a scaling behavior of moisture-induced grain degradation in polycrystalline CH 3NH 3PbI 3 films. The degradation rates of CH 3NH 3PbI 3 films in moisture were shown to be sensitive to the grain sizes. The duration that was needed for different films to degrade by the same percent showed a linear relationship with the grain size, despite the fact that the filmsmore » were formed by five different deposition methods. This scaling behavior can be explained by the degradation along the in-plane direction, which is initiated at the grain boundary (GB). The GBs of CH 3NH 3PbI 3 films consist of an amorphous intergranular layer, which allows quick diffusion of moisture into the perovskite films. It was found that thermal annealing induced surface self-passivation plays a critical role in stabilizing the surfaces of thin films and single crystals by reducing the moisture-sensitive methylammonium ions at the surface. Finally, the determination of the scaling behavior of grain degradation highlights the importance of stabilizing the GBs to improve the stability of perovskite solar cells.« less