Work stress of women in sewing machine operation.

PubMed

Nag, A; Desai, H; Nag, P K

1992-06-01

The study examined the work stresses of 107 women who were engaged in sewing machine operation in small garment manufacturing units. Of the three types of sewing machines (motor-operated, full and half shuttle foot-operated), 74% of the machines were foot-operated, where throttle action of the lower limb is required to move the shuttle of the machine. The motor-operated machines were faster than the foot-operated machines. The short cycle sewing work involves repetitive action of hand and feet. The women had to maintain a constant seated position on a stool without backrest and the body inclined forward. Long-term sewing work had a cumulative load on the musculo-skeletal structures, including the vertebral column and reflected in the form of high prevalence of discomfort and pain in different body parts. About 68% of the women complained of back pain, among whom 35% reported a persistent low back pain. Common sewing work accident is piercing of the needle through the fingers, particularly the right forefingers. Unsatisfactory man-machine incompatibility, work posture and fatigue, improper coordination of eye, leg and hand are the major problems of the operators. The design mis-match of the work place may be significantly improved by taking women's anthropometric dimensions in modifying the workplace, i.e. the seat surface, seat height, work height, backrest, etc.

Improving machine operation management efficiency via improving the vehicle park structure and using the production operation information database

NASA Astrophysics Data System (ADS)

Koptev, V. Yu

2017-02-01

The work represents the results of studying basic interconnected criteria of separate equipment units of the transport network machines fleet, depending on production and mining factors to improve the transport systems management. Justifying the selection of a control system necessitates employing new methodologies and models, augmented with stability and transport flow criteria, accounting for mining work development dynamics on mining sites. A necessary condition is the accounting of technical and operating parameters related to vehicle operation. Modern open pit mining dispatching systems must include such kinds of the information database. An algorithm forming a machine fleet is presented based on multi-variation task solution in connection with defining reasonable operating features of a machine working as a part of a complex. Proposals cited in the work may apply to mining machines (drilling equipment, excavators) and construction equipment (bulldozers, cranes, pile-drivers), city transport and other types of production activities using machine fleet.

MACHINE TOOL OPERATOR--GENERAL, ENTRY, SUGGESTED GUIDE FOR A TRAINING COURSE.

ERIC Educational Resources Information Center

RONEY, MAURICE W.; AND OTHERS

THE PURPOSE OF THIS CURRICULUM GUIDE IS TO ASSIST THE ADMINISTRATOR AND INSTRUCTOR IN PLANNING AND DEVELOPING MANPOWER DEVELOPMENT AND TRAINING PROGRAMS TO PREPARE MACHINE TOOL OPERATORS FOR ENTRY-LEVEL POSITIONS. THE COURSE OUTLINE PROVIDES UNITS IN -- (1) ORIENTATION, (2) BENCH WORK, (3) SHOP MATHEMATICS, (4) BLUEPRINT READING AND SKETCHING, (5)…

The determination of effective injury controls for metal-cutting lathe operators.

PubMed

Etherton, J R; Trump, T R; Jensen, R C

1981-01-01

Operators of metal-working lathes are one of the largest manufacturing machine worker populations in the United States. Machines (other than vehicular) account for over 10% of occupational injuries each year. An estimated 3,400 operators of metal-working lathes suffer lost-time injuries annually in the United States. Some of these are fatal. Therefore an investigation was undertaken to determine methods for reducing injuries to lathe operators. Three methods were used: (i) review of injury reports, (ii) human factors analysis, and (iii) fault-tree procedures. The investigation followed the man-machine systems approach of looking for injury-producing dysfunctions between the lathe and the lathe operator. The major sources of injury were found to be chips and workholding devices. Secondary tasks were found to be more hazardous than is generally recognized. The use of three methods for approaching the problem was found to be useful in that injury controls were identified which are likely to be adopted because of their potential for improving safety without adversely affecting productivity.

Machine Shop. Module 8: CNC (Computerized Numerical Control). Instructor's Guide.

ERIC Educational Resources Information Center

Crosswhite, Dwight

This document consists of materials for a five-unit course on the following topics: (1) safety guidelines; (2) coordinates and dimensions; (3) numerical control math; (4) programming for numerical control machines; and (5) setting and operating the numerical control machine. The instructor's guide begins with a list of competencies covered in the…

Sewing Skills for Home and Community Services. Student Material.

ERIC Educational Resources Information Center

Sharpton, James L.

These student learning materials deal with basic sewing skills. The following topics are covered in the individual units: the principal parts of a sewing machine and their purposes; procedures for caring for a sewing machine (putting it away, lubricating it, and changing the needle); operation of an unthreaded sewing machine (maintaining correct…

Superconducting Coil Winding Machine Control System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nogiec, J. M.; Kotelnikov, S.; Makulski, A.

The Spirex coil winding machine is used at Fermilab to build coils for superconducting magnets. Recently this ma-chine was equipped with a new control system, which al-lows operation from both a computer and a portable remote control unit. This control system is distributed between three layers, implemented on a PC, real-time target, and FPGA, providing respectively HMI, operational logic and direct controls. The system controls motion of all mechan-ical components and regulates the cable tension. Safety is ensured by a failsafe, redundant system.

Light-operated machines based on threaded molecular structures.

PubMed

Credi, Alberto; Silvi, Serena; Venturi, Margherita

2014-01-01

Rotaxanes and related species represent the most common implementation of the concept of artificial molecular machines, because the supramolecular nature of the interactions between the components and their interlocked architecture allow a precise control on the position and movement of the molecular units. The use of light to power artificial molecular machines is particularly valuable because it can play the dual role of "writing" and "reading" the system. Moreover, light-driven machines can operate without accumulation of waste products, and photons are the ideal inputs to enable autonomous operation mechanisms. In appropriately designed molecular machines, light can be used to control not only the stability of the system, which affects the relative position of the molecular components but also the kinetics of the mechanical processes, thereby enabling control on the direction of the movements. This step forward is necessary in order to make a leap from molecular machines to molecular motors.

Upgrading the fuel-handling machine of the Novovoronezh nuclear power plant unit no. 5

NASA Astrophysics Data System (ADS)

Terekhov, D. V.; Dunaev, V. I.

2014-02-01

The calculation of safety parameters was carried out in the process of upgrading the fuel-handling machine (FHM) of the Novovoronezh nuclear power plant (NPP) unit no. 5 based on the results of quantitative safety analysis of nuclear fuel transfer operations using a dynamic logical-and-probabilistic model of the processing procedure. Specific engineering and design concepts that made it possible to reduce the probability of damaging the fuel assemblies (FAs) when performing various technological operations by an order of magnitude and introduce more flexible algorithms into the modernized FHM control system were developed. The results of pilot operation during two refueling campaigns prove that the total reactor shutdown time is lowered.

Fluid Power Systems Maintenance and Operation. Instructor's Guide.

ERIC Educational Resources Information Center

Paule, Bob A.

Written to complement the Fluid Power/Basic Hydraulic and Basic Pneumatics guides, this curriculum guide contains materials for a seven-unit course in fluid power systems maintenance and operation. Units, which consist of one to eight lessons, cover these topics: preventive maintenance, repair machine malfunctions, overhaul/recondition hydraulic…

Automated solar panel assembly line

NASA Technical Reports Server (NTRS)

Somberg, H.

1981-01-01

The initial stage of the automated solar panel assembly line program was devoted to concept development and proof of approach through simple experimental verification. In this phase, laboratory bench models were built to demonstrate and verify concepts. Following this phase was machine design and integration of the various machine elements. The third phase was machine assembly and debugging. In this phase, the various elements were operated as a unit and modifications were made as required. The final stage of development was the demonstration of the equipment in a pilot production operation.

Learning Activity Packets for Milling Machines. Unit II--Horizontal Milling Machines.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) outlines the study activities and performance tasks covered in a related curriculum guide on milling machines. The course of study in this LAP is intended to help students learn to set up and operate a horizontal mill. Tasks addressed in the LAP include mounting style "A" or "B" arbors and adjusting arbor…

Development of a kolanut peeling device.

PubMed

Kareem, I; Owolarafe, O K; Ajayi, O A

2014-10-01

A kolanut peeling machine was designed, constructed and evaluated for the postharvest processing of the seed. The peeling machine consists of a standing frame, peeling unit and hopper. The peeling unit consists of a special paddle, which mixes the kolanut, rubs them against one another and against the wall of the barrel and also conveys the kolanut to the outlet. The performance of the kolanut peeling machine was evaluated for its peeling efficiency at different moisture content (53.0, 57.6, 61.4 % w.b.) and speeds of operation of the machine. The result of the analysis of variance shows that the main factors and their interaction had significant effects (p < 0.05) on the peeling efficiency of the machine. The result also shows that the peeling efficiency of the machine increased as the moisture content increase and decreased with increase in machine speed. The highest efficiency of the machine was 60.3 % at a moisture content of 61.4 % w.b. and speed of 40 rpm.

40 CFR 63.5830 - What are my options for meeting the standards for pultrusion operations subject to the 60 weight...

Code of Federal Regulations, 2011 CFR

2011-07-01

... pultrusion machines that meet the criteria in paragraphs (b)(1) through (10) of this section. (1) The... openings to allow material to enter and exit the enclosure. (2) For open bath pultrusion machines with a... entrance of the die. (3) For open bath pultrusion machines without a radio frequency pre-heat unit, the...

40 CFR 63.5830 - What are my options for meeting the standards for pultrusion operations subject to the 60 weight...

Code of Federal Regulations, 2014 CFR

2014-07-01

... pultrusion machines that meet the criteria in paragraphs (b)(1) through (10) of this section. (1) The... openings to allow material to enter and exit the enclosure. (2) For open bath pultrusion machines with a... entrance of the die. (3) For open bath pultrusion machines without a radio frequency pre-heat unit, the...

40 CFR 63.5830 - What are my options for meeting the standards for pultrusion operations subject to the 60 weight...

Code of Federal Regulations, 2013 CFR

2013-07-01

... pultrusion machines that meet the criteria in paragraphs (b)(1) through (10) of this section. (1) The... openings to allow material to enter and exit the enclosure. (2) For open bath pultrusion machines with a... entrance of the die. (3) For open bath pultrusion machines without a radio frequency pre-heat unit, the...

Model for Assembly Line Re-Balancing Considering Additional Capacity and Outsourcing to Face Demand Fluctuations

NASA Astrophysics Data System (ADS)

Samadhi, TMAA; Sumihartati, Atin

2016-02-01

The most critical stage in a garment industry is sewing process, because generally, it consists of a number of operations and a large number of sewing machines for each operation. Therefore, it requires a balancing method that can assign task to work station with balance workloads. Many studies on assembly line balancing assume a new assembly line, but in reality, due to demand fluctuation and demand increased a re-balancing is needed. To cope with those fluctuating demand changes, additional capacity can be carried out by investing in spare sewing machine and paying for sewing service through outsourcing. This study develops an assembly line balancing (ALB) model on existing line to cope with fluctuating demand change. Capacity redesign is decided if the fluctuation demand exceeds the available capacity through a combination of making investment on new machines and outsourcing while considering for minimizing the cost of idle capacity in the future. The objective of the model is to minimize the total cost of the line assembly that consists of operating costs, machine cost, adding capacity cost, losses cost due to idle capacity and outsourcing costs. The model develop is based on an integer programming model. The model is tested for a set of data of one year demand with the existing number of sewing machines of 41 units. The result shows that additional maximum capacity up to 76 units of machine required when there is an increase of 60% of the average demand, at the equal cost parameters..

Cold Saw Operator (iron & steel) 6-88.651; Cold Sizing Mill Operator (iron & steel) 4-88.315; Decambering Mill Operator (iron & steel) 6-88.346; Flying Cut-Off Machine Operator (iron & steel) 6-88.655; Rotary Straightener Operator (iron & steel) 6-88.346; Straightener Machine Operator (iron & steel) 6-88.354; Tube Straightener Operator (iron & steel) 6-88.346; Welder (iron & steel) 4-88.343; Welder, Assistant (iron & steel) 4-88.344--Technical

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Control and protection system for an installation for the combined production of electrical and thermal energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Agazzone, U.; Ausiello, F.P.

1981-06-23

A power-generating installation comprises a plurality of modular power plants each comprised of an internal combustion engine connected to an electric machine. The electric machine is used to start the engine and thereafter operates as a generator supplying power to an electrical network common to all the modular plants. The installation has a control and protection system comprising a plurality of control modules each associated with a respective plant, and a central unit passing control signals to the modules to control starting and stopping of the individual power plants. Upon the detection of abnormal operation or failure of its associatedmore » power plant, each control module transmits an alarm signal back to the central unit which thereupon stops, or prevents the starting, of the corresponding power plant. Parameters monitored by each control module include generated current and inter-winding leakage current of the electric machine.« less

Condition monitoring of a prototype turbine. Description of the system and main results

NASA Astrophysics Data System (ADS)

Valero, C.; Egusquiza, E.; Presas, A.; Valentin, D.; Egusquiza, M.; Bossio, M.

2017-04-01

The fast change in new renewable energy is affecting directly the required operating range of hydropower plants. According to the present demand of electricity, it is necessary to generate different levels of power. Because of its ease to regulate and its huge storage capacity of energy, hydropower is the unique energy source that can adapt to the demand. Today, the required operating range of turbine units is expected to extend from part load to overload. These extreme operations points can cause several pressure pulsations, cavitation and vibrations in different parts of the machine. To determine the effects on the machine, vibration measurements are necessary in actual machines. Vibrations can be used for machinery protection and to identify problems in the machine (diagnosis). In this paper, some results obtained in a hydropower plant are presented. The variation of global levels and vibratory signatures has been analysed as function as gross head, transducer location and operating points.

Single phase space laundry development

NASA Technical Reports Server (NTRS)

Colombo, Gerald V.; Putnam, David F.; Lunsford, Teddie D.; Streech, Neil D.; Wheeler, Richard R., Jr.; Reimers, Harold

1993-01-01

This paper describes a newly designed, 2.7 Kg (6 pound) capacity, laundry machine called the Single Phase Laundry (SPSL). The machine was designed to wash and dry crew clothing in a micro-gravity environment. A prototype unit was fabricated for NASA-JSC under a Small Business Innovated Research (SBIR) contract extending from September 1990 to January 1993. The unit employs liquid jet agitation, microwave vacuum drying, and air jet tumbling, which was perfected by KC-135 zero-g flight testing. Operation is completely automated except for loading and unloading clothes. The unit uses about 20 percent less power than a conventional household appliance.

Advanced Aircraft Interfaces: The Machine Side of the Man-Machine Interface (Les Interfaces sur les Avions de Pointe: L’Aspect Machine de l’Interface Homme-Machine)

DTIC Science & Technology

1992-10-01

Manager , Advanced Transport Operating Systems Program Office Langley Research Center Mail Stop 265 Hampton, VA 23665-5225 United States Programme Committee...J.H.Lind, and C.G.Burge Advanced Cockpit - Mission and Image Management 4 by J. Struck Aircrew Acceptance of Automation in the Cockpit 5 by M. Hicks and I...DESIGN CONCEPTS AND TOOLS A Systems Approach to the Advanced Aircraft Man-Machine Interface 23 by F. Armogida Management of Avionics Data in the Cockpit

PUP: An Architecture to Exploit Parallel Unification in Prolog

DTIC Science & Technology

1988-03-01

environment stacking mo del similar to the Warren Abstract Machine [23] since it has been shown to be super ior to other known models (see [21]). The storage...execute in groups of independent operations. Unifications belonging to different group s may not overlap. Also unification operations belonging to the...since all parallel operations on the unification units must complete before any of the units can star t executing the next group of parallel

Experimental Design and Analysis of M1A1 Commander/Gunner Performance during CONOPS (Continuous Operations) Using the U-COFT (Unit Conduct of Fire Trainer)

DTIC Science & Technology

1989-09-01

gun b. 7.62-mm coax manchine gun c. Commander’s weapon station caliber .50 machine gun d. M250 grenade launchers 2. Ammunition Simulation a. 105-mm...7.62-mm machine gun f. M250 smoke grenades 3. Normal Mode Simulation a. Stabilized coax machine gun b. Stabilized main gun c. Commander’s weapon d

THRESHOLD LOGIC SYNTHESIS OF SEQUENTIAL MACHINES.

DTIC Science & Technology

The application of threshold logic to the design of sequential machines is the subject of this research. A single layer of threshold logic units in...advantages of fewer components because of the use of threshold logic, along with very high-speed operation resulting from the use of only a single layer of...logic. In some instances, namely for asynchronous machines, the only delay need be the natural delay of the single layer of threshold elements. It is

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yale, S H

A survey was conducted of x-ray facilities in 2000 dental offices under actual operating conditions. Each of 10 dental schools in the United States collected data on 200 local dental offices to implement geographic analysis of the status of radiation hygiene in the offices. The data provided records of roentgen (r) output of each machine, relative r dose to patient, and dose to operator. In addition, specific information relating to both operator and machine was coiiected and evaluated. Some dentists were found to be operating under unsafe conditions, but the average dentist covered in the survey was statistically safe. Onmore » the basis of the survey, it was concluded that the probiem of radiation hazards in dentistry will be resolved when all dental x-ray machines are properly filtered and collimated and high-speed dental x-ray film is used. (P.C.H.)« less

A Methodology for Protective Vibration Monitoring of Hydropower Units Based on the Mechanical Properties.

PubMed

Nässelqvist, Mattias; Gustavsson, Rolf; Aidanpää, Jan-Olov

2013-07-01

It is important to monitor the radial loads in hydropower units in order to protect the machine from harmful radial loads. Existing recommendations in the standards regarding the radial movements of the shaft and bearing housing in hydropower units, ISO-7919-5 (International Organization for Standardization, 2005, "ISO 7919-5: Mechanical Vibration-Evaluation of Machine Vibration by Measurements on Rotating Shafts-Part 5: Machine Sets in Hydraulic Power Generating and Pumping Plants," Geneva, Switzerland) and ISO-10816-5 (International Organization for Standardization, 2000, "ISO 10816-5: Mechanical Vibration-Evaluation of Machine Vibration by Measurements on Non-Rotating Parts-Part 5: Machine Sets in Hydraulic Power Generating and Pumping Plants," Geneva, Switzerland), have alarm levels based on statistical data and do not consider the mechanical properties of the machine. The synchronous speed of the unit determines the maximum recommended shaft displacement and housing acceleration, according to these standards. This paper presents a methodology for the alarm and trip levels based on the design criteria of the hydropower unit and the measured radial loads in the machine during operation. When a hydropower unit is designed, one of its design criteria is to withstand certain loads spectra without the occurrence of fatigue in the mechanical components. These calculated limits for fatigue are used to set limits for the maximum radial loads allowed in the machine before it shuts down in order to protect itself from damage due to high radial loads. Radial loads in hydropower units are caused by unbalance, shape deviations, dynamic flow properties in the turbine, etc. Standards exist for balancing and manufacturers (and power plant owners) have recommendations for maximum allowed shape deviations in generators. These standards and recommendations determine which loads, at a maximum, should be allowed before an alarm is sent that the machine needs maintenance. The radial bearing load can be determined using load cells, bearing properties multiplied by shaft displacement, or bearing bracket stiffness multiplied by housing compression or movement. Different load measurement methods should be used depending on the design of the machine and accuracy demands in the load measurement. The methodology presented in the paper is applied to a 40 MW hydropower unit; suggestions are presented for the alarm and trip levels for the machine based on the mechanical properties and radial loads.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

1995-12-05

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other mineral particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

1995-01-01

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

1997-02-11

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

Flotation machine and process for removing impurities from coals

DOEpatents

Szymocha, Kazimierz; Ignasiak, Boleslaw; Pawlak, Wanda; Kulik, Conrad; Lebowitz, Howard E.

1997-01-01

The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other minerals particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal.

Government review of the Mod-2 wind turbine (as-built)

NASA Technical Reports Server (NTRS)

Johnson, W. R.; Birchenough, A. G.; Linscott, B. S.; Reagan, J. R.; Sirocky, P. J.; Sizemore, R. L.; Sullivan, T. L.; Holeman, R. H.

1985-01-01

The findings and recommendations of the Government committee formed to conduct an as-built review of the three Mod-2 wind turbine units at Goldendale, Washington are given. The purpose of the review was to identify any critical deficiencies in machine components that could result in failure, and to recommend any necessary corrective action before resuming safe machine operation. The review concluded that one of the deficiencies identified would preclude planned attended or unattended operation, provided that certain corrective actions were implemented.

Effective Dust Control Systems on Concrete Dowel Drilling Machinery

PubMed Central

Echt, Alan S.; Sanderson, Wayne T.; Mead, Kenneth R.; Feng, H. Amy; Farwick, Daniel R.; Farwick, Dawn Ramsey

2016-01-01

Rotary-type percussion dowel drilling machines, which drill horizontal holes in concrete pavement, have been documented to produce respirable crystalline silica concentrations above recommended exposure criteria. This places operators at potential risk for developing health effects from exposure. United States manufacturers of these machines offer optional dust control systems. The effectiveness of the dust control systems to reduce respirable dust concentrations on two types of drilling machines was evaluated under controlled conditions with the machines operating inside large tent structures in an effort to eliminate secondary exposure sources not related to the dowel-drilling operation. Area air samples were collected at breathing zone height at three locations around each machine. Through equal numbers of sampling rounds with the control systems randomly selected to be on or off, the control systems were found to significantly reduce respirable dust concentrations from a geometric mean of 54 mg per cubic meter to 3.0 mg per cubic meter on one machine and 57 mg per cubic meter to 5.3 mg per cubic meter on the other machine. This research shows that the dust control systems can dramatically reduce respirable dust concentrations by over 90% under controlled conditions. However, these systems need to be evaluated under actual work conditions to determine their effectiveness in reducing worker exposures to crystalline silica below hazardous levels. PMID:27074062

Mountain Plains Learning Experience Guide: Appliance Repair. Course: Motor-Operated Appliances.

ERIC Educational Resources Information Center

Ziller, T.

One of two individualized courses included in an appliance repair curriculum, this course is designed to prepare students to operate, diagnose malfunctions, repair, and service motor operated appliances. The course is comprised of seven units: (1) Mixers and Blenders, (2) Vacuum Cleaners and Floor Polishers, (3) Washing Machines, (4) Garbage…

77 FR 30501 - Uncovered Innerspring Units From the People's Republic of China: Initiation of Anticircumvention...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... type of assembly operation (i.e., manual or semi-automated) are low. Petitioner asserts that in the... low if Reztec relies on a semi-automated assembly operation where a machine is used to assemble the... States.\\29\\ Petitioner believes Reztec's assembly operations likely rely on relatively unskilled, low...

Secure Autonomous Automated Scheduling (SAAS). Rev. 1.1

NASA Technical Reports Server (NTRS)

Walke, Jon G.; Dikeman, Larry; Sage, Stephen P.; Miller, Eric M.

2010-01-01

This report describes network-centric operations, where a virtual mission operations center autonomously receives sensor triggers, and schedules space and ground assets using Internet-based technologies and service-oriented architectures. For proof-of-concept purposes, sensor triggers are received from the United States Geological Survey (USGS) to determine targets for space-based sensors. The Surrey Satellite Technology Limited (SSTL) Disaster Monitoring Constellation satellite, the UK-DMC, is used as the space-based sensor. The UK-DMC's availability is determined via machine-to-machine communications using SSTL's mission planning system. Access to/from the UK-DMC for tasking and sensor data is via SSTL's and Universal Space Network's (USN) ground assets. The availability and scheduling of USN's assets can also be performed autonomously via machine-to-machine communications. All communication, both on the ground and between ground and space, uses open Internet standards

Soil disturbances from horse/mule logging operations coupled with machines in the Southern United States

Treesearch

Suraj P. Shrestha; Bobby L. Lanford; Robert Rummer; Mark Dubois

2008-01-01

Forest harvesting with animals is a labor-intensive operation. While mechanized logging is very efficient for large tracts of timber, it is often disruptive to the soil. Small logging operations using animals may be less environmentally disruptive. To better understand horse/mule logging performances for soil disturbance, five different horse/mule harvesting operations...

21 CFR 1141.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-04-01

.... Required warning means the combination of one of the textual warning statements and its accompanying color... operates a facility where vending machines or self-service displays of cigarettes are permitted. United...

Low-cost boring mill

NASA Technical Reports Server (NTRS)

Hibdon, R. A.

1979-01-01

Portable unit and special fixture serve as boring mill. Machine, fabricated primarily from scrap metal, was designed and set up in about 12 working days. It has reduced setup and boring time by 66 percent as compared with existing boring miles, thereby making latter available for other jobs. Unit can be operated by one man.

Position error compensation via a variable reluctance sensor applied to a Hybrid Vehicle Electric machine.

PubMed

Bucak, Ihsan Ömür

2010-01-01

In the automotive industry, electromagnetic variable reluctance (VR) sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV) system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion.

Position Error Compensation via a Variable Reluctance Sensor Applied to a Hybrid Vehicle Electric Machine

PubMed Central

Bucak, İhsan Ömür

2010-01-01

In the automotive industry, electromagnetic variable reluctance (VR) sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV) system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion. PMID:22294906

Digital controller for a Baum folding machine. [providing automatic counting and machine shutoff

NASA Technical Reports Server (NTRS)

Bryant, W. H. (Inventor)

1974-01-01

A digital controller for controlling the operation of a folding machine enables automatic folding of a desired number of sheets responsive to entry of that number into a selector. The controller includes three decade counter stages for corresponding rows of units, tens and hundreds push buttons. Each stage including a decimal-to-BCD encoder, a buffer register, and a digital or binary counter. The BCD representation of the selected count for each digit is loaded into the respective decade down counters. Pulses generated by a sensor and associated circuitry are used to decrease the count in the decade counters. When the content of the decade counter reaches either 0 or 1, a solenoid control valve is actuated which interrupts operation of the machine. A repeat switch, when actuated, prevents clearing of the buffer registers so that multiple groups of the same number of sheets can be folded without reentering the number into the selector.

Effective dust control systems on concrete dowel drilling machinery.

PubMed

Echt, Alan S; Sanderson, Wayne T; Mead, Kenneth R; Feng, H Amy; Farwick, Daniel R; Farwick, Dawn Ramsey

2016-09-01

Rotary-type percussion dowel drilling machines, which drill horizontal holes in concrete pavement, have been documented to produce respirable crystalline silica concentrations above recommended exposure criteria. This places operators at potential risk for developing health effects from exposure. United States manufacturers of these machines offer optional dust control systems. The effectiveness of the dust control systems to reduce respirable dust concentrations on two types of drilling machines was evaluated under controlled conditions with the machines operating inside large tent structures in an effort to eliminate secondary exposure sources not related to the dowel-drilling operation. Area air samples were collected at breathing zone height at three locations around each machine. Through equal numbers of sampling rounds with the control systems randomly selected to be on or off, the control systems were found to significantly reduce respirable dust concentrations from a geometric mean of 54 mg per cubic meter to 3.0 mg per cubic meter on one machine and 57 mg per cubic meter to 5.3 mg per cubic meter on the other machine. This research shows that the dust control systems can dramatically reduce respirable dust concentrations by over 90% under controlled conditions. However, these systems need to be evaluated under actual work conditions to determine their effectiveness in reducing worker exposures to crystalline silica below hazardous levels.

Multi-parameter monitoring of electrical machines using integrated fibre Bragg gratings

NASA Astrophysics Data System (ADS)

Fabian, Matthias; Hind, David; Gerada, Chris; Sun, Tong; Grattan, Kenneth T. V.

2017-04-01

In this paper a sensor system for multi-parameter electrical machine condition monitoring is reported. The proposed FBG-based system allows for the simultaneous monitoring of machine vibration, rotor speed and position, torque, spinning direction, temperature distribution along the stator windings and on the rotor surface as well as the stator wave frequency. This all-optical sensing solution reduces the component count of conventional sensor systems, i.e., all 48 sensing elements are contained within the machine operated by a single sensing interrogation unit. In this work, the sensing system has been successfully integrated into and tested on a permanent magnet motor prototype.

Dose rate evaluation of workers on the operation floor in Fukushima-Daiichi Unit 3

NASA Astrophysics Data System (ADS)

Matsushita, Kaoru; Kurosawa, Masahiko; Shirai, Keisuke; Matsuoka, Ippei; Mukaida, Naoki

2017-09-01

At Fukushima Daiichi Nuclear Power Plant Unit 3, installation of a fuel handling machine is planned to support the removal of spent fuel. The dose rates at the workplace were calculated based on the source distribution measured using a collimator in order to confirm that the dose rates on the operation floor were within a manageable range. It was confirmed that the accuracy of the source distribution was C/M = 1.0-2.4. These dose rates were then used to plan the work on the operation floor.

Design for multipurpose use: an application of DfE concept in a developing economy

NASA Astrophysics Data System (ADS)

Dunmade, Israel

2004-12-01

Design for Environment (DfE) has been defined as the systematic integration of environmental considerations into product and process design. And it has been discovered that material and space can be saved when several functions are integrated into a single product by taking advantage of common components. In this design and development project, a multipurpose thresher was designed based on an integrated concept of design for modularity, disassembly, demanufacturing and remanufacturing. The machine can be used to thresh various types of farm produce such as rice, sorghum, cowpea and rye by changing the concave and the cylinder (threshing drum). The configuration of the machine enables access to most of the component parts without changing the tools needed for disassembly because the same type of fasteners was used. Furthermore, the functional units (the shelling unit, the separation unit and the grading unit) were assembled into modules such that only the faulty part needs to be replaced if necessary. The design was so simplified that the operator can make the changes for different uses without any difficulty. The machine has been successfully tested with a number of these products and it is scheduled for tests with other produce like corn and peanuts. The modularity of the functional unit will facilitate multi-lifecycle use of machine and/or its component parts. The uniformity of the liaisons and simplification of the configuration will reduce both the disassembly times and maintenance cost. By this integration, the material requirements for four different machines are conserved, environmental emissions that would be associated with the manufacture, transportation and disposal of four machines are eliminated while the capital requirements by farmers for machinery are reduced to about a quarter. Consequently the total lifecycle cost is kept minimum while the eco-efficiency is maximized.

Machine vision inspection of railroad track

DOT National Transportation Integrated Search

2011-01-10

North American Railways and the United States Department of Transportation : (US DOT) Federal Railroad Administration (FRA) require periodic inspection of railway : infrastructure to ensure the safety of railway operation. This inspection is a critic...

Influence of forces acting on side of machine on precision machining of large diameter holes

NASA Astrophysics Data System (ADS)

Fedorenko, M. A.; Bondarenko, J. A.; Sanina, T. M.

2018-03-01

One of the most important factors that increase efficiency, durability and reliability of rotating units is precision installation, preventive maintenance work, timely replacing of a failed or worn components and assemblies. These works should be carried out in the operation of the equipment, as the downtime in many cases leads to large financial losses. Stop of one unit of an industrial enterprise can interrupt the technological chain of production, resulting in a possible stop of the entire equipment. Improving the efficiency and optimization of the repair process increases accuracy of installation work when installing equipment, conducting restoration under operating conditions relevant for enterprises of different industries because it eliminates dismantling the equipment, sending it to maintenance, the expectation of equipment return, the new installation with the required quality and accuracy of repair.

Evaluation of application for approval of alternative methodology for compliance with the NESHAP for shipbuilding and ship repair and recommended requirements for compliance (application submitted by Metro Machine Corporation, Norfolk, Virginia). Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serageldin, M.A.

1999-07-01

The US Environmental Protection Agency is providing background information that supports the use of Metro Machine Corporation`s (MMC) compliant all position enclosure (CAPE) plus air management system and regenerative thermal oxidizer (RTO) (CAPE + RTO System) as an alternative means of limiting the emissions of volatile organic hazardous air pollutants per volume of applied solids (nonvolatiles). This document also explains how the authors arrived at the operating, recordkeeping, and reporting conditions that MMC must meet for approval. The add-on control system they used consists of a pollution capture unit operation (CAPE) plus air management system and a destruction unit operationmore » (RTO). When operated according to the specified procedures, it will control emissions to a level no greater than that from using coatings which comply with the limits in Table 2 of 40 CFR Part 63, Subpart II.« less

Architecture and data processing alternatives for Tse computer. Volume 1: Tse logic design concepts and the development of image processing machine architectures

NASA Technical Reports Server (NTRS)

Rickard, D. A.; Bodenheimer, R. E.

1976-01-01

Digital computer components which perform two dimensional array logic operations (Tse logic) on binary data arrays are described. The properties of Golay transforms which make them useful in image processing are reviewed, and several architectures for Golay transform processors are presented with emphasis on the skeletonizing algorithm. Conventional logic control units developed for the Golay transform processors are described. One is a unique microprogrammable control unit that uses a microprocessor to control the Tse computer. The remaining control units are based on programmable logic arrays. Performance criteria are established and utilized to compare the various Golay transform machines developed. A critique of Tse logic is presented, and recommendations for additional research are included.

Washing machine usage in remote aboriginal communities.

PubMed

Lloyd, C R

1998-10-01

The use of washing machines was investigated in two remote Aboriginal communities in the Anangu Pitjantjatjara homelands. The aim was to look both at machine reliability and to investigate the health aspect of washing clothes. A total of 39 machines were inspected for wear and component reliability every three months over a one-year period. Of these, 10 machines were monitored in detail for water consumption, hours of use and cycles of operation. The machines monitored were Speed Queen model EA2011 (7 kg washing load) commercial units. The field survey results suggested a high rate of operation of the machines with an average of around 1,100 washing cycles per year (range 150 and 2,300 cycles per year). The results were compared with available figures for the average Australian household. A literature survey, to ascertain the health outcomes relating to washing clothes and bedding, confirmed that washing machines are efficient at removal of bacteria from clothes and bedding but suggested that recontamination of clothing after washing often negated the prior removal. High temperature washing (> 60 degrees C) appeared to be advantageous from a health perspective. With regards to larger organisms, while dust mites and body lice transmission between people would probably be decreased by washing clothes, scabies appeared to be mainly transmitted by body contact and thus transmission would be only marginally decreased by the use of washing machines.

Troubleshooting of an Electromechanical System (Westinghouse PLC Controlling a Pneumatic Robot). High-Technology Training Module.

ERIC Educational Resources Information Center

Tucker, James D.

This training module on the troubleshooting of an electromechanical system, The Westinghouse Programmable Logic Controller (PLC) controlling a pneumatic robot, is used for a troubleshooting unit in an electromechanical systems/robotics and automation systems course. In this unit, students locate and repair a defect in a PLC-operated machine. The…

The Joint Operating Agreement: A Marvelous Machine with Damned Tight Steering.

ERIC Educational Resources Information Center

Pilgrim, Tim A.; Simpson, Roger

The Newspaper Preservation Act of 1970 is frequently viewed as a legislative device for averting the failure of a competing metropolitan daily newspaper and is said to create, for the formerly competing newspapers, a monolithic management unit which enjoys advantages over the two publishing units it replaces. A study examined one of those…

Wear resistance of machine tools' bionic linear rolling guides by laser cladding

NASA Astrophysics Data System (ADS)

Wang, Yiqiang; Liu, Botao; Guo, Zhengcai

2017-06-01

In order to improve the rolling wear resistance (RWR) of linear rolling guides (LRG) as well as prolong the life of machine tools, various shape samples with different units spaces ranged from 1 to 5 mm are designed through the observation of animals in the desert and manufactured by laser cladding. Wear resistance tests reproducing closely the real operational condition are conducted by using a homemade linear reciprocating wear test machine, and wear resistance is evaluated by means of weight loss measurement. Results indicate that the samples with bionic units have better RWR than the untreated one, of which the reticulate treated sample with unit space 3 mm present the best RWR. More specifically, among the punctuate treated samples, the mass loss increases with the increase of unit space; among the striate treated samples, the mass loss changes slightly with the increase of unit space, attaining a minimum at the unit space of 4 mm; among the reticulate treated samples, with the increase of unit space, the mass loss initially decreases, but turns to increase after reaching a minimum at the unit space of 3 mm. Additionally, the samples with striate shape perform better wear resistance than the other shape groups on the whole. From the ratio value of laser treated area to contacted area perspective, that the samples with ratio value between 0.15 and 0.3 possess better wear resistance is concluded.

Machine protection system for rotating equipment and method

DOEpatents

Lakshminarasimha, Arkalgud N.; Rucigay, Richard J.; Ozgur, Dincer

2003-01-01

A machine protection system and method for rotating equipment introduces new alarming features and makes use of full proximity probe sensor information, including amplitude and phase. Baseline vibration amplitude and phase data is estimated and tracked according to operating modes of the rotating equipment. Baseline vibration and phase data can be determined using a rolling average and variance and stored in a unit circle or tracked using short term average and long term average baselines. The sensed vibration amplitude and phase is compared with the baseline vibration amplitude and phase data. Operation of the rotating equipment can be controlled based on the vibration amplitude and phase.

Performance Assessment of Flashed Steam Geothermal Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alt, Theodore E.

1980-12-01

Five years of operating experience at the Comision Federal de Electricidad (CFE) Cerro Prieto flashed steam geothermal power plant are evaluated from the perspective of U. S. utility operations. We focus on the design and maintenance of the power plant that led to the achievement of high plant capacity factors for Units No. 1 and 2 since commercial operation began in 1973. For this study, plant capacity factor is the ratio of the average load on the machines or equipment for the period of time considered to the capacity rating of the machines or equipment. The plant capacity factor ismore » the annual gross output in GWh compared to 657 GWh (2 x 37.5 MW x 8760 h). The CFE operates Cerro Prieto at base load consistent with the system connected electrical demand of the Baja California Division. The plant output was curtailed during the winter months of 1973-1975 when the system electric demand was less than the combined output capability of Cerro Prieto and the fossil fuel plant near Tijuana. Each year the system electric demand has increased and the Cerro Prieto units now operate at full load all the time. The CFE added Units 3 and 4 to Cerro Prieto in 1979 which increased the plant name plate capacity to 150 MW. Part of this additional capacity will supply power to San Diego Gas and Electric Company through an interconnection across the border. The achievement of a high capacity factor over an extensive operating period was influenced by operation, design, and maintenance of the geothermal flash steam power plant.« less

Failure detection in high-performance clusters and computers using chaotic map computations

DOEpatents

Rao, Nageswara S.

2015-09-01

A programmable media includes a processing unit capable of independent operation in a machine that is capable of executing 10.sup.18 floating point operations per second. The processing unit is in communication with a memory element and an interconnect that couples computing nodes. The programmable media includes a logical unit configured to execute arithmetic functions, comparative functions, and/or logical functions. The processing unit is configured to detect computing component failures, memory element failures and/or interconnect failures by executing programming threads that generate one or more chaotic map trajectories. The central processing unit or graphical processing unit is configured to detect a computing component failure, memory element failure and/or an interconnect failure through an automated comparison of signal trajectories generated by the chaotic maps.

The Efficiency and the Scalability of an Explicit Operator on an IBM POWER4 System

NASA Technical Reports Server (NTRS)

Frumkin, Michael; Biegel, Bryan A. (Technical Monitor)

2002-01-01

We present an evaluation of the efficiency and the scalability of an explicit CFD operator on an IBM POWER4 system. The POWER4 architecture exhibits a common trend in HPC architectures: boosting CPU processing power by increasing the number of functional units, while hiding the latency of memory access by increasing the depth of the memory hierarchy. The overall machine performance depends on the ability of the caches-buses-fabric-memory to feed the functional units with the data to be processed. In this study we evaluate the efficiency and scalability of one explicit CFD operator on an IBM POWER4. This operator performs computations at the points of a Cartesian grid and involves a few dozen floating point numbers and on the order of 100 floating point operations per grid point. The computations in all grid points are independent. Specifically, we estimate the efficiency of the RHS operator (SP of NPB) on a single processor as the observed/peak performance ratio. Then we estimate the scalability of the operator on a single chip (2 CPUs), a single MCM (8 CPUs), 16 CPUs, and the whole machine (32 CPUs). Then we perform the same measurements for a chache-optimized version of the RHS operator. For our measurements we use the HPM (Hardware Performance Monitor) counters available on the POWER4. These counters allow us to analyze the obtained performance results.

Development of an Electric Motor Powered Low Cost Coconut Deshelling Machine

NASA Astrophysics Data System (ADS)

Mondal, Imdadul Hoque; Prasanna Kumar, G. V.

2016-06-01

An electric motor powered coconut deshelling machine was developed in line with the commercially available unit, but with slight modifications. The machine worked on the principle that the coconut shell can be caused to fail in shear and compressive forces. It consisted of a toothed wheel, a deshelling rod, an electric motor, and a compound chain drive. A bevelled 16 teeth sprocket with 18 mm pitch was used as the toothed wheel. Mild steel round bar of 18 mm diameter was used as the deshelling rod. The sharp edge tip of the deshelling rod was inserted below the shell to apply shear force on the shell, and the fruit was tilted toward the rotary toothed wheel to apply the compressive force on the shell. The speed of rotation of the toothed wheel was set at 34 ± 2 rpm. The output capacity of the machine was found to be 24 coconuts/h with 95 % of the total time effectively used for deshelling. The labour requirement was found to be 43 man-h/1000 nuts. About 13 % of the kernels got scraped and about 7 % got sliced during the operation. The developed coconut deshelling machine was recommended for the minimum annual use of 200 h or deshelling of 4700 coconuts per year. The cost of operation for 200 h of annual use was found to be about ` 47/h. The developed machine was found to be simple, easy to operate, energy efficient, safe and reduce drudgery involved in deshelling by conventional methods.

Description of photovoltaic village power systems in the United States and Africa

NASA Technical Reports Server (NTRS)

Ratajczak, A. F.; Bifano, W. J.

1979-01-01

Photovoltaic power systems in remote villages in the United States and Africa are described. These projects were undertaken to demonstrate that existing photovoltaic system technology is capable of providing electrical power for basic domestic services for the millions of small, remote communities in both developed and developing countries. One system is located in the Papago Indian Village of Schuchuli in southwest Arizona (U. S.) and became operational 16 December 1978. The other system is located in Tangaye, a rural village in Upper Volta, Africa. It became operational 1 March 1979. The Schuchuli system has a 3.5 kW (peak) solar array which provides electric power for village water pumping, a refrigerator for each family, lights in the village buildings, and a community washing machine and sewing machine. The 1.8 kW (peak) Tangaye system provides power for community water pumping, flour milling and lights in the milling building. These are both stand-alone systems (i.e., no back-up power source) which are being operated and maintained by local personnel. Both systems are instrumented. Systems operations are being monitored by NASA to measure design adequacy and to refine designs for future systems.

Investigation of Combined Motor/Magnetic Bearings for Flywheel Energy Storage Systems

NASA Technical Reports Server (NTRS)

Hofmann, Heath

2003-01-01

Dr. Hofmann's work in the summer of 2003 consisted of two separate projects. In the first part of the summer, Dr. Hofmann prepared and collected information regarding rotor losses in synchronous machines; in particular, machines with low rotor losses operating in vacuum and supported by magnetic bearings, such as the motor/generator for flywheel energy storage systems. This work culminated in a presentation at NASA Glenn Research Center on this topic. In the second part, Dr. Hofmann investigated an approach to flywheel energy storage where the phases of the flywheel motor/generator are connected in parallel with the phases of an induction machine driving a mechanical actuator. With this approach, additional power electronics for driving the flywheel unit are not required. Simulations of the connection of a flywheel energy storage system to a model of an electromechanical actuator testbed at NASA Glenn were performed that validated the proposed approach. A proof-of-concept experiment using the D1 flywheel unit at NASA Glenn and a Sundstrand induction machine connected to a dynamometer was successfully conducted.

Cutting sound enhancement system for mining machines

DOEpatents

Leigh, Michael C.; Kwitowski, August J.

1992-01-01

A cutting sound enhancement system (10) for transmitting an audible signal from the cutting head (101) of a piece of mine machinery (100) to an operator at a remote station (200), wherein, the operator using a headphone unit (14) can monitor the difference in sounds being made solely by the cutting head (101) to determine the location of the roof, floor, and walls of a coal seam (50).

One-Piece Force-Transducer Body

NASA Technical Reports Server (NTRS)

Meyer, R. A.

1986-01-01

Rugged unit designed to operate in severe environment. Forcetransducer body designed for measurement of loads on specimens tested in hydrogen gas at temperatures up to 2,000 degree F (1,090 degree C). Body has symmetrical radial-shear-beam configuration and machined in one piece from bar stock.

Fabrication of Flex Joint Utilizing Additively Manufactured Parts

NASA Technical Reports Server (NTRS)

Eddleman, David; Richard, Jim

2015-01-01

The Selective Laser Melting (SLM) manufacturing technique has been utilized in the manufacture of a flex joint typical of those found in rocket engine and main propulsion system ducting. The SLM process allowed for the combination of parts that are typically machined separately and welded together. This resulted in roughly a 65% reduction of the total number of parts, roughly 70% reduction in the total number of welds, and an estimated 60% reduction in the number of machining operations. The majority of the new design was in three SLM pieces. These pieces, as well as a few traditionally fabricated parts, were assembled into a complete unit, which has been pressure tested. The design and planned cryogenic testing of the unit will be presented.

Salad Machine - A vegetable production unit for long duration space missions

NASA Technical Reports Server (NTRS)

Kliss, M.; Macelroy, R. D.

1990-01-01

A review of NASA CELSS development specific to vegetable cultivation during space missions is presented in terms of enhancing the quality of life for space crews. A cultivation unit is being developed to permit the production of 600 grams of edible salad vegetables per week, thereby allowing one salad per crew member three times weekly. Plant-growth requirements are set forth for the specific vegetables, and environmental subsystems are listed. Several preprototype systems are discussed, and one particular integrated-systems design concept is presented in detail with views of the proposed rack configuration. The Salad Machine is developed exclusively from CELSS-derived technology, and the major challenge is the mitigation of the effects of plant-growth requirements on other space-mission facility operations.

Modification of a Superficial X-Ray Therapy Machine for Rectal Contact Therapy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barish, Robert J.; Donohue, Karen Episcopia

2015-01-15

X-ray therapy of superficial rectal cancers using a hand-held 50 kV contact unit (Philips RT-50) in a technique first described by Papillon had reached a point of widening clinical acceptability when the manufacturer of this equipment discontinued its production. To pursue this endocavitary approach to rectal therapy, technical modifications have to be made to conventional superficial x-ray therapy machines. Advantages over the original Papillon method include remote viewing of the lesion through the proctoscopic cone and a lower radiation exposure for the operator. We have evaluated a Bucky Combination Therapy Unit under conditions in which the operating voltage (65 kV),more » target skin distance (23.6 cm), and added filtration (0.39 mm Al) were selected in order to match as closely as possible the beam penetration characteristics of the “standard” (Papillon) technique. With this equipment, the thermal characteristics of the tube anode and housing limit the amount of radiation that can be delivered before a “rest period” for the machine is needed. In practice, 3 minutes of irradiation at an exposure rate of 500 R/min can be performed followed by an interval of 3 minutes before irradiation can be resumed.« less

Traction sheave elevator, hoisting unit and machine space

DOEpatents

Hakala, Harri; Mustalahti, Jorma; Aulanko, Esko

2000-01-01

Traction sheave elevator consisting of an elevator car moving along elevator guide rails, a counterweight moving along counterweight guide rails, a set of hoisting ropes (3) on which the elevator car and counterweight are suspended, and a drive machine unit (6) driving a traction sheave (7) acting on the hoisting ropes (3) and placed in the elevator shaft. The drive machine unit (6) is of a flat construction. A wall of the elevator shaft is provided with a machine space with its open side facing towards the shaft, the essential parts of the drive machine unit (6) being placed in the space. The hoisting unit (9) of the traction sheave elevator consists of a substantially discoidal drive machine unit (6) and an instrument panel (8) mounted on the frame (20) of the hoisting unit.

Feasibility Study of Jupiter Icy Moons Orbiter Permanent Magnet Alternator Start Sequence

NASA Technical Reports Server (NTRS)

Kenny, Barbara H.; Tokars, Roger P.

2006-01-01

The Jupiter Icy Moons Orbiter (JIMO) mission was a proposed, (recently cancelled) long duration science mission to study three moons of Jupiter: Callisto, Ganymede, and Europa. One design of the JIMO spacecraft used a nuclear heat source in conjunction with a Brayton rotating machine to generate electrical power for the electric thrusters and the spacecraft bus. The basic operation of the closed cycle Brayton system was as follows. The working fluid, a heliumxenon gas mixture, first entered a compressor, then went through a recuperator and hot-side heat exchanger, then expanded across a turbine that drove an alternator, then entered the cold-side of the recuperator and heat exchanger and finally returned to the compressor. The spacecraft was to be launched with the Brayton system off-line and the nuclear reactor shut down. Once the system was started, the helium-xenon gas would be circulated into the heat exchangers as the nuclear reactors were activated. Initially, the alternator unit would operate as a motor so as to drive the turbine and compressor to get the cycle started. This report investigated the feasibility of the start up sequence of a permanent magnet (PM) machine, similar in operation to the alternator unit, without any position or speed feedback sensors ("sensorless") and with a variable load torque. It is found that the permanent magnet machine can start with sensorless control and a load torque of up to 30 percent of the rated value.

Maximizing the Potential of the Special Operations Forces and General Purpose Forces

DTIC Science & Technology

2014-05-22

States (Washington, DC: Government Printing Office, 2013), I-15). 8David Tucker and Christopher J. Lamb , United States Special Operations Forces...functionally it was a messy misapplication of forces, that got the job done in a highly inefficient manner. 59Mets, 114. 60Chris Lamb , “Belief Systems and...Taking out the planes was a standoff operation, a job for a three-man team equipped with AT-4s ( shoulder -fired rockets) and machine guns,’ he

Connectionist models of conditioning: A tutorial

PubMed Central

Kehoe, E. James

1989-01-01

Models containing networks of neuron-like units have become increasingly prominent in the study of both cognitive psychology and artificial intelligence. This article describes the basic features of connectionist models and provides an illustrative application to compound-stimulus effects in respondent conditioning. Connectionist models designed specifically for operant conditioning are not yet widely available, but some current learning algorithms for machine learning indicate that such models are feasible. Conversely, designers for machine learning appear to have recognized the value of behavioral principles in producing adaptive behavior in their creations. PMID:16812604

Concept and design engineering: endourology operating room.

PubMed

Sabnis, Ravindra; Ganesamoni, Raguram; Mishra, Shashikant; Sinha, Lokesh; Desai, Mahesh R

2013-03-01

A dedicated operating room with fluoroscopic imaging capability and adequate data connectivity is important to the success of any endourology program. Proper understanding of the recent developments in technology in relation to operating room is necessary before planning an endourology operating room. An endourology operating room is a fluorocompatible operating room with enough space to accommodate equipment like multiple flat monitors to display video, C-arm with its monitor, ultrasonography machine, laser machine, intracorporeal lithotripsy unit, irrigation pumps and two large trolleys with instruments. This operating room is integrated with devices to continuously record and archive data from endovision and surface cameras, ultrasound and fluoroscopy. Moreover, advances made in data relay systems have created seamless two-way communication between the operating room and electronic medical records, radiological picture archiving and communication system, classroom, auditorium and literally anywhere in the world. A dedicated endourology operating room is required for any hospital, which has a significant amount of endourology procedures. A custom-made integrated endourology operating room will facilitate endourology procedures, smoothen the workflow in operating room and improve patient outcomes. Meticulous planning and involving experts in the field are critical for the success of the project.

Robots Are Taking Over--Who Does What.

ERIC Educational Resources Information Center

Garrison, H. Don

Robots are machines designed to replace human labor. A fear of vast unemployment due to robots seems unfounded, however, since industrialization creates many more jobs and automation requires technologists to build, program, maintain, and operate sophisticated equipment. Robots possess an intelligence unit, a manipulator, and an end effector.…

Methods of Cost Reduction for United States Coast Guard Telephone Systems.

DTIC Science & Technology

1981-03-01

System (’FTS) for a single low utilization command is questionable. Small FAX machines such as EXXON’s QWIP /FAX can be purchased at approxi- mately...unsatisfactory operating condi- tion. Electrical faults, such as leakage or poor insulation, noise induction, crosstalk, or poor transmission

Competency Based Curriculum for Clothing Services and Production Sewing.

ERIC Educational Resources Information Center

Blake, Charlotte

Designed to meet individual needs and learning levels of high school and postsecondary students enrolled in vocational training for occupations in clothing services and production sewing, this competency-based curriculum teaches skills in alterations, dressmaking, and power sewing machine operations. Skills are organized into 13 units: Awareness…

Mountain Plains Learning Experience Guide: Carpentry. Course: Finish.

ERIC Educational Resources Information Center

Leland, Lyle

One of two individualized courses included in a carpentry curriculum, this course is structured to provide the information, procedures, and experiences to complete the carpentry requirements following the framing operation. The course is comprised of five units: (1) Machine Processes, (2) Exterior Wall Coverings and Cornice, (3) Windows and Trim,…

Computing at the speed limit (supercomputers)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernhard, R.

1982-07-01

The author discusses how unheralded efforts in the United States, mainly in universities, have removed major stumbling blocks to building cost-effective superfast computers for scientific and engineering applications within five years. These computers would have sustained speeds of billions of floating-point operations per second (flops), whereas with the fastest machines today the top sustained speed is only 25 million flops, with bursts to 160 megaflops. Cost-effective superfast machines can be built because of advances in very large-scale integration and the special software needed to program the new machines. VLSI greatly reduces the cost per unit of computing power. The developmentmore » of such computers would come at an opportune time. Although the US leads the world in large-scale computer technology, its supremacy is now threatened, not surprisingly, by the Japanese. Publicized reports indicate that the Japanese government is funding a cooperative effort by commercial computer manufacturers to develop superfast computers-about 1000 times faster than modern supercomputers. The US computer industry, by contrast, has balked at attempting to boost computer power so sharply because of the uncertain market for the machines and the failure of similar projects in the past to show significant results.« less

National Ignition Facility Control and Information System Operational Tools

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marshall, C D; Beeler, R G; Bowers, G A

The National Ignition Facility (NIF) in Livermore, California, is the world's highest-energy laser fusion system and one of the premier large scale scientific projects in the United States. The system is designed to setup and fire a laser shot to a fusion ignition or high energy density target at rates up to a shot every 4 hours. NIF has 192 laser beams delivering up to 1.8 MJ of energy to a {approx}2 mm target that is planned to produce >100 billion atm of pressure and temperatures of >100 million degrees centigrade. NIF is housed in a ten-story building footprint themore » size of three football fields as shown in Fig. 1. Commissioning was recently completed and NIF will be formally dedicated at Lawrence Livermore National Laboratory on May 29, 2009. The control system has 60,000 hardware controls points and employs 2 million lines of control system code. The control room has highly automated equipment setup prior to firing laser system shots. This automation has a data driven implementation that is conducive to dynamic modification and optimization depending on the shot goals defined by the end user experimenters. NIF has extensive facility machine history and infrastructure maintenance workflow tools both under development and deployed. An extensive operational tools suite has been developed to support facility operations including experimental shot setup, machine readiness, machine health and safety, and machine history. The following paragraphs discuss the current state and future upgrades to these four categories of operational tools.« less

Stirling machine operating experience

NASA Technical Reports Server (NTRS)

Ross, Brad; Dudenhoefer, James E.

1991-01-01

Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that Stirling machines are capable of reliable and lengthy lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and were not expected to operate for any lengthy period of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered.

Hard permanent magnet development trends and their application to A.C. machines

NASA Technical Reports Server (NTRS)

Mildrum, H. F.

1981-01-01

The physical and magnetic properties of Mn-Al-C, Fe-Cr-Co, and RE-TM (rare earth-transition metal intermetallics) in polymer and soft metal bonded or sintered form are considered for ac circuit machine usage. The manufacturing processes for the magnetic materials are reviewed, and the mechanical and electrical properties of the magnetic materials are compared, with consideration given to the reference Alnico magnet. The Mn-Al-C magnets have the same magnetic properties and costs as Alnico units, operate well at low temperatures, but have poor high temperature performance. Fe-Cr-Co magnets also have comparable cost to Alnico magnets, and operate at high or low temperature, but are brittle, expensive, and contain Co. RE-Co magnets possess a high energy density, operate well in a wide temperature range, and are expensive. Recommendation for exploring the rare-earth alternatives are offered.

Washing machine related injuries in children: a continuing threat

PubMed Central

Warner, B; Kenney, B; Rice, M

2003-01-01

Objective: To describe washing machine related injuries in children in the United States. Methods: Injury data for 496 washing machine related injuries documented by the Consumer Product Safety Commission's National Electronic Injury Surveillance System and death certificate data files were analyzed. Gender, age, diagnosis, body part injured, disposition, location and mechanism of injury were considered in the analysis of data. Results: The upper extremities were most frequently injured in washing machine related injuries, especially with wringer machines. Fewer than 10% of patients required admission, but automatic washers accounted for most of these and for both of the deaths. Automatic washer injuries involved a wider range of injury mechanism, including 23 children who fell from the machines while in baby seats. Conclusions: Though most injuries associated with washing machines are minor, some are severe and devastating. Many of the injuries could be avoided with improvements in machine design while others suggest a need for increased education of potential dangers and better supervision of children if they are allowed access to areas where washing machines are operating. Furthermore, washing machines should only be used for their intended purpose. Given the limitations of educational efforts to prevent injuries, health professionals should have a major role in public education regarding these seemingly benign household appliances. PMID:14693900

Sensor-Based Optimized Control of the Full Load Instability in Large Hydraulic Turbines

PubMed Central

Presas, Alexandre; Valero, Carme; Egusquiza, Eduard

2018-01-01

Hydropower plants are of paramount importance for the integration of intermittent renewable energy sources in the power grid. In order to match the energy generated and consumed, Large hydraulic turbines have to work under off-design conditions, which may lead to dangerous unstable operating points involving the hydraulic, mechanical and electrical system. Under these conditions, the stability of the grid and the safety of the power plant itself can be compromised. For many Francis Turbines one of these critical points, that usually limits the maximum output power, is the full load instability. Therefore, these machines usually work far away from this unstable point, reducing the effective operating range of the unit. In order to extend the operating range of the machine, working closer to this point with a reasonable safety margin, it is of paramount importance to monitor and to control relevant parameters of the unit, which have to be obtained with an accurate sensor acquisition strategy. Within the framework of a large EU project, field tests in a large Francis Turbine located in Canada (rated power of 444 MW) have been performed. Many different sensors were used to monitor several working parameters of the unit for all its operating range. Particularly for these tests, more than 80 signals, including ten type of different sensors and several operating signals that define the operating point of the unit, were simultaneously acquired. The present study, focuses on the optimization of the acquisition strategy, which includes type, number, location, acquisition frequency of the sensors and corresponding signal analysis to detect the full load instability and to prevent the unit from reaching this point. A systematic approach to determine this strategy has been followed. It has been found that some indicators obtained with different types of sensors are linearly correlated with the oscillating power. The optimized strategy has been determined based on the correlation characteristics (linearity, sensitivity and reactivity), the simplicity of the installation and the acquisition frequency necessary. Finally, an economic and easy implementable protection system based on the resulting optimized acquisition strategy is proposed. This system, which can be used in a generic Francis turbine with a similar full load instability, permits one to extend the operating range of the unit by working close to the instability with a reasonable safety margin. PMID:29601512

Sensor-Based Optimized Control of the Full Load Instability in Large Hydraulic Turbines.

PubMed

Presas, Alexandre; Valentin, David; Egusquiza, Mònica; Valero, Carme; Egusquiza, Eduard

2018-03-30

Hydropower plants are of paramount importance for the integration of intermittent renewable energy sources in the power grid. In order to match the energy generated and consumed, Large hydraulic turbines have to work under off-design conditions, which may lead to dangerous unstable operating points involving the hydraulic, mechanical and electrical system. Under these conditions, the stability of the grid and the safety of the power plant itself can be compromised. For many Francis Turbines one of these critical points, that usually limits the maximum output power, is the full load instability. Therefore, these machines usually work far away from this unstable point, reducing the effective operating range of the unit. In order to extend the operating range of the machine, working closer to this point with a reasonable safety margin, it is of paramount importance to monitor and to control relevant parameters of the unit, which have to be obtained with an accurate sensor acquisition strategy. Within the framework of a large EU project, field tests in a large Francis Turbine located in Canada (rated power of 444 MW) have been performed. Many different sensors were used to monitor several working parameters of the unit for all its operating range. Particularly for these tests, more than 80 signals, including ten type of different sensors and several operating signals that define the operating point of the unit, were simultaneously acquired. The present study, focuses on the optimization of the acquisition strategy, which includes type, number, location, acquisition frequency of the sensors and corresponding signal analysis to detect the full load instability and to prevent the unit from reaching this point. A systematic approach to determine this strategy has been followed. It has been found that some indicators obtained with different types of sensors are linearly correlated with the oscillating power. The optimized strategy has been determined based on the correlation characteristics (linearity, sensitivity and reactivity), the simplicity of the installation and the acquisition frequency necessary. Finally, an economic and easy implementable protection system based on the resulting optimized acquisition strategy is proposed. This system, which can be used in a generic Francis turbine with a similar full load instability, permits one to extend the operating range of the unit by working close to the instability with a reasonable safety margin.

76 FR 46853 - International Business Machines Corporation, ITD Business Unit, Division 7, E-mail and...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-03

...] International Business Machines Corporation, ITD Business Unit, Division 7, E-mail and Collaboration Group... Business Machines Corporation (IBM), ITD Business Unit, Division 7, E- mail and Collaboration Group... Business Unit, Division 7, E-mail and Collaboration [[Page 46854

A performance comparison of the IBM RS/6000 and the Astronautics ZS-1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, W.M.; Abraham, S.G.; Davidson, E.S.

1991-01-01

Concurrent uniprocessor architectures, of which vector and superscalar are two examples, are designed to capitalize on fine-grain parallelism. The authors have developed a performance evaluation method for comparing and improving these architectures, and in this article they present the methodology and a detailed case study of two machines. The runtime of many programs is dominated by time spent in loop constructs - for example, Fortran Do-loops. Loops generally comprise two logical processes: The access process generates addresses for memory operations while the execute process operates on floating-point data. Memory access patterns typically can be generated independently of the data inmore » the execute process. This independence allows the access process to slip ahead, thereby hiding memory latency. The IBM 360/91 was designed in 1967 to achieve slip dynamically, at runtime. One CPU unit executes integer operations while another handles floating-point operations. Other machines, including the VAX 9000 and the IBM RS/6000, use a similar approach.« less

Analysis of total productive maintenance (TPM) implementation using overall equipment effectiveness (OEE) and six big losses: A case study

NASA Astrophysics Data System (ADS)

Martomo, Zenithia Intan; Laksono, Pringgo Widyo

2018-02-01

In improving the productivity of the machine, the management of the decision or maintenance policy must be appropriate. In Spinning II unit at PT Apac Inti Corpora, there are 124 ring frame machines that often have breakdown and cause a high downtime so that the production target is not achieved, so this research was conducted on the ring frame machine. This study aims to measure the value of equipment effectiveness, find the root cause of the problem and provide suggestions for improvement. This research begins with measuring the achievement of overall equipment effectiveness (OEE) value, then identifying the six big losses that occur. The results show that the average value of OEE in the ring frame machine is 79.96%, the effectiveness value is quite low because the standard of OEE value for world class company ideally is 85%. The biggest factor that influences the low value of OEE is performance rate with percentage factor six big losses at reduced speed losses of 17.303% of all time loss. Proposed improvement actions are the application of autonomous maintenance, providing training for operators and maintenance technicians and supervising operators in the workplace.

Contributions a l'etude et a l'application industrielle de la machine asynchrone

NASA Astrophysics Data System (ADS)

Ouhrouche, Mohand-Ameziane

The work presented in this thesis, done in the Electrical Drives Laboratory of Electrical and Computer Engineering Department, deals with the industrial applications of a three-phase induction machine (electrical drives and electricity generation). This thesis, characterized by its multidisciplinary content, has two major parts. The first one deals with the on-line and off-line parametric identification of the induction machine model necessary to achieve accurate vector control strategy. The second part, which is a resume of a research work sponsored by Hydro-Quebec, deals with the application of an induction machine in Asynchronous Non Utility Generators units (ANUG). As it is shown in the following, major scientific contributions are made in both two parts. In the first part of our research work, we propose a new speed sensorless vector control strategy for an induction machine, which is adaptive to the rotor resistance variations. The proposed control strategy is based on the Extended Kalman Filter approach and a decoupling controller which takes into account the rotor resistance variations. The consideration of coupled electrical and mechanical modes leads to a fifth order nonlinear model of the induction machine. The load torque is taken as a function of the rotor angular speed. The Extended Kalman Filter, based on the process's nonlinear (bilinear) model, estimate simultaneously the rotor resistance, angular speed and the flux vector from the startup to the steady state equilibrium point. The machine-converter-control system is implemented in MATLAB/SIMULINK environment and the obtained results confirm the robustness of the proposed scheme. As in the electrical drives erea, the induction machine is now widely used by small to medium power Non Utility Generator units (NUG) to produce electricity. In Quebec, these NUGs units are integrated into the Hydro-Quebec 25 kV distribution system via transformer which exhibit nonlinear characteristics. We have shown by using the ElectroMagnetic Program (EMTP) that, in some islanding scenarios, i.e. that the NUG unit is disconnected from the power grid, in addition to frequency variations, appearence of high an abnormal overvoltages, ferroresonance should occur. As a consequence, normal protective devices could fail to securely operate, which could cause serious damages to the equipment and the maintenance staff. This result, established for the first time , can be useful to improve the reliability of the NUGs units and is considered important by the power engineering community. This has led to a publication in the John Wiley & Sons Encyclopedia of Electrical and Electronics Engineering which will be available in February 1999 ( http://www.engr.wisc.edu/ ece/ece).

Single instruction computer architecture and its application in image processing

NASA Astrophysics Data System (ADS)

Laplante, Phillip A.

1992-03-01

A single processing computer system using only half-adder circuits is described. In addition, it is shown that only a single hard-wired instruction is needed in the control unit to obtain a complete instruction set for this general purpose computer. Such a system has several advantages. First it is intrinsically a RISC machine--in fact the 'ultimate RISC' machine. Second, because only a single type of logic element is employed the entire computer system can be easily realized on a single, highly integrated chip. Finally, due to the homogeneous nature of the computer's logic elements, the computer has possible implementations as an optical or chemical machine. This in turn suggests possible paradigms for neural computing and artificial intelligence. After showing how we can implement a full-adder, min, max and other operations using the half-adder, we use an array of such full-adders to implement the dilation operation for two black and white images. Next we implement the erosion operation of two black and white images using a relative complement function and the properties of erosion and dilation. This approach was inspired by papers by van der Poel in which a single instruction is used to furnish a complete set of general purpose instructions and by Bohm- Jacopini where it is shown that any problem can be solved using a Turing machine with one entry and one exit.

Detection and analysis of part load and full load instabilities in a real Francis turbine prototype

NASA Astrophysics Data System (ADS)

Presas, Alexandre; Valentin, David; Egusquiza, Eduard; Valero, Carme

2017-04-01

Francis turbines operate in many cases out of its best efficiency point, in order to regulate their output power according to the instantaneous energy demand of the grid. Therefore, it is of paramount importance to analyse and determine the unstable operating points for these kind of units. In the framework of the HYPERBOLE project (FP7-ENERGY-2013-1; Project number 608532) a large Francis unit was investigated numerically, experimentally in a reduced scale model and also experimentally and numerically in the real prototype. This paper shows the unstable operating points identified during the experimental tests on the real Francis unit and the analysis of the main characteristics of these instabilities. Finally, it is shown that similar phenomena have been identified on previous research in the LMH (Laboratory for Hydraulic Machines, Lausanne) with the reduced scale model.

[Effect of manual cleaning and machine cleaning for dental handpiece].

PubMed

Zhou, Xiaoli; Huang, Hao; He, Xiaoyan; Chen, Hui; Zhou, Xiaoying

2013-08-01

Comparing the dental handpiece' s cleaning effect between manual cleaning and machine cleaning. Eighty same contaminated dental handpieces were randomly divided into experimental group and control group, each group contains 40 pieces. The experimental group was treated by full automatic washing machine, and the control group was cleaned manually. The cleaning method was conducted according to the operations process standard, then ATP bioluminescence was used to test the cleaning results. Average relative light units (RLU) by ATP bioluminescence detection were as follows: Experimental group was 9, control group was 41. The two groups were less than the recommended RLU value provided by the instrument manufacturer (RLU < or = 45). There was significant difference between the two groups (P < 0.05). The cleaning quality of the experimental group was better than that of control group. It is recommended that the central sterile supply department should clean dental handpieces by machine to ensure the cleaning effect and maintain the quality.

Knitting-Machine Operator (knit goods) 4-14.061--Technical Report.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Machine Shop. Module 5: Lathes. Instructor's Guide.

ERIC Educational Resources Information Center

Nobles, Jack

This document consists of materials for a 10-unit course on the following topics: (1) types and parts of lathes; (2) lathe accessories, maintenance, and safety; (3) lathe operations and tooling; (4) lathe calculations; (5) lathe taper and thread applications; (6) planning considerations; (7) cutting fluids, lathe center alignment, and lathe gaps;…

United States Air Force F-35A Operational Basing Environmental Impact Statement. Appendix E: Comments

DTIC Science & Technology

2013-09-01

Nicholas M Civ USAF HQ ACC/A7NS No F-35s in Burlington, Vermont, please! Wherever I go, when people hear I am from Vermont, they wax enthusiastic...them to upkeep a machine that’s sole purpose i s to fly cross t he ocean (or too wherever) and t ake the l ives of many others? Even i f we except this...monstrosi t y of a machine , can we really entrust it to the care of an organization that appears to be unable to write an accurate report? We may

Disease model: a simplified approach for analysis and management of human error: a quality improvement study.

PubMed

Ahmad-Sabry, Mohammad H I

2015-04-01

During 6 weeks, we had 4 incidents of echocardiography machine malfunction. There were 3 in the operating room, which were damaged due to intravenous (IV) fluid spillage over the keyboard of the machine leading to burning of the keyboard electric connection, and 1 in the cardiology department, which was damagaed due to spillage of coffee on it. The malfunction had an economic impact on the hospital (about $ 20,000) in addition to the nonavailability of the ultrasound (US) machine for the cardiac patient after the incident till the end of the case and for consequent cases till the fixation of the machine. We undertook an analysis of the incidents using simplified approach. The first incident happened when changing an empty IV fluid bag for a full one led to spillage of some fluid onto the keyboard. The second incidence was due to the use of needle to depressurize a medication bottle for continuous IV drip, and the third event was due to disconnection of the IV set from the bottle during transfer of the patient from operation room to intensive care unit. The fundamental problem is of course that fluid is harmful to the US machine. In addition, the machines are in a position between the patient bed and anesthesia machine. This means that IV pulls are on each side of the patient bed, which makes the machine vulnerable to fluid spillage. We considered a machine modification, to create a protective cover, but this was hindered by complexity of keyboard of the US machine, technical and financial challenges, and the time it would take to achieve. Second, we considered the creation of a protocol, with putting the machine in a position where no IV pulls are around and transferring the machine out of the room when transferring the patient will endanger the machine by the IV fluid. Third, changing of human behavior; to do this, we announced the protocol in our anesthesia conference to make it known to each and every one. We taught residents, fellows, and staff about the new protocol.Our simplified approach was effective for the prevention of fluid spillage over the US machine.

Assessing a Novel Method to Reduce Anesthesia Machine Contamination: A Prospective, Observational Trial.

PubMed

Biddle, Chuck J; George-Gay, Beverly; Prasanna, Praveen; Hill, Emily M; Davis, Thomas C; Verhulst, Brad

2018-01-01

Anesthesia machines are known reservoirs of bacterial species, potentially contributing to healthcare associated infections (HAIs). An inexpensive, disposable, nonpermeable, transparent anesthesia machine wrap (AMW) may reduce microbial contamination of the anesthesia machine. This study quantified the density and diversity of bacterial species found on anesthesia machines after terminal cleaning and between cases during actual anesthesia care to assess the impact of the AMW. We hypothesized reduced bioburden with the use of the AMW. In a prospective, experimental research design, the AMW was used in 11 surgical cases (intervention group) and not used in 11 control surgical cases. Cases were consecutively assigned to general surgical operating rooms. Seven frequently touched and difficult to disinfect "hot spots" were cultured on each machine preceding and following each case. The density and diversity of cultured colony forming units (CFUs) between the covered and uncovered machines were compared using Wilcoxon signed-rank test and Student's t -tests. There was a statistically significant reduction in CFU density and diversity when the AMW was employed. The protective effect of the AMW during regular anesthetic care provides a reliable and low-cost method to minimize the transmission of pathogens across patients and potentially reduces HAIs.

Assessment of microwave-based clinical waste decontamination unit.

PubMed

Hoffman, P N; Hanley, M J

1994-12-01

A clinical waste decontamination unit that used microwave-generated heat was assessed for operator safety and efficacy. Tests with loads artificially contaminated with aerosol-forming particles showed that no particles were detected outside the machine provided the seals and covers were correctly seated. Thermometric measurement of a self-generated steam decontamination cycle was used to determine the parameters needed to ensure heat disinfection of the waste reception hopper, prior to entry for maintenance or repair. Bacterial and thermometric test pieces were passed through the machine within a full load of clinical waste. These test pieces, designed to represent a worst case situation, were enclosed in aluminium foil to shield them from direct microwave energy. None of the 100 bacterial test pieces yielded growth on culture and all 100 thermal test pieces achieved temperatures in excess of 99 degrees C during their passage through the decontamination unit. It was concluded that this method may be used to render safe the bulk of of ward-generated clinical waste.

Computer network defense system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Urias, Vincent; Stout, William M. S.; Loverro, Caleb

A method and apparatus for protecting virtual machines. A computer system creates a copy of a group of the virtual machines in an operating network in a deception network to form a group of cloned virtual machines in the deception network when the group of the virtual machines is accessed by an adversary. The computer system creates an emulation of components from the operating network in the deception network. The components are accessible by the group of the cloned virtual machines as if the group of the cloned virtual machines was in the operating network. The computer system moves networkmore » connections for the group of the virtual machines in the operating network used by the adversary from the group of the virtual machines in the operating network to the group of the cloned virtual machines, enabling protecting the group of the virtual machines from actions performed by the adversary.« less

The Transatlantic Essay Contest and the Planning Principles of the North African Campaign

DTIC Science & Technology

2013-05-23

Miracle of Dunkirk (New York: Viking Press, 1982), ix. 69Winston Churchill, "We Shall Fight on the Beaches" http://www.winstonchurchill.org/learn... Dunkirk , France to the United Kingdom from May 27, 1940 to June 4, 1940. GYMNAST Plan for the British invasion of North Africa. Later SUPER...Walter. The Miracle of Dunkirk . New York: Viking Press, 1982. Machin, Mark A. "Rommel, Operational Art and the Battle of El Alamien." Newport, RI: United

Crystalline molecular machines: Encoding supramolecular dynamics into molecular structure

PubMed Central

Garcia-Garibay, Miguel A.

2005-01-01

Crystalline molecular machines represent an exciting new branch of crystal engineering and materials science with important implications to nanotechnology. Crystalline molecular machines are crystals built with molecules that are structurally programmed to respond collectively to mechanic, electric, magnetic, or photonic stimuli to fulfill specific functions. One of the main challenges in their construction derives from the picometric precision required for their mechanic operation within the close-packed, self-assembled environment of crystalline solids. In this article, we outline some of the general guidelines for their design and apply them for the construction of molecular crystals with units intended to emulate macroscopic gyroscopes and compasses. Recent advances in the preparation, crystallization, and dynamic characterization of these interesting systems offer a foothold to the possibilities and help highlight some avenues for future experimentation. PMID:16046543

A centerless grinding unit used for precisely processing ferrules of optical fiber connector

NASA Astrophysics Data System (ADS)

Wu, Yongbo; Kondo, Takahiro; Kato, Masana

2005-02-01

This paper describes the development of a centerless grinding unit used for precisely processing ferrules, a key component of optical fiber connectors. In conventional processing procedure, the outer diameter of a ferrule is ground by employing a special machine tool, i.e., centerless grinder. However, in the case of processing small amount of ferrules, introducing a centerless grinder leads to high processing cost. Therefore, in order to take measures against this problem, the present authors propose a new centerless grinding technique where a compact centerless grinding unit, which is composed of an ultrasonic elliptic-vibration shoe, a workrest blade, and their respective holders, is installed on a popular surface grinder to perform the centerless grinding operations for outer diameter machining of ferrules. In this work, a unit is designed and constructed, and is installed on a surface grinder equipped with a diamond grinding wheel. Then, the performance of the unit is examined experimentally followed by grinding tests of ferrule"s outer diameter. As a result, the roundness of the ferrule"s outer diameter improved from the original value of around 3μm to the final value of around 0.5 μm, confirming the validity of the new technique.

Life cycle costing as a decision making tool for technology acquisition in radio-diagnosis

PubMed Central

Chakravarty, Abhijit; Debnath, Jyotindu

2014-01-01

Background Life cycle costing analysis is an emerging conceptual tool to validate capital investment in healthcare. Methods A preliminary study was done to analyze the long-term cost impact of acquiring a new 3 T MRI system when compared to technological upgradation of the existing 1.5 T MRI system with a view to evolve a decision matrix for correct investment planning and technology management. Operating costing method was utilized to estimate cost per unit MRI scan, costing inputs were considered for the existing 1.5 T and the proposed 3 T machine. Cost for each expected year in the life span of both 1.5 T and 3 T MRI scan options were then discounted to its Net Present Value. Net Present Value thus calculated for both the alternative options of 1.5 T and 3 T MRI machine was charted along with various intangible but critical Figures of Merit (FOM) to create a decision matrix for capital investment planning. Result Considering all fixed and variable costs contributing towards assumed operation, unit cost per MRI procedure was found to be Rs. 4244.58 for the 1.5 T upgrade and Rs. 6059.37 for the new 3 T MRI machine. Life Cycle Cost Analysis of the proposed 1.5 T upgrade and new 3 T machine showed a Net Present Value of Rs. 42,148,587.80 and Rs. 27,587,842.38 respectively. Conclusion The utility of life cycle costing as a strategic decision making tool towards evaluating alternative options for capital investment planning in health care environment is reiterated. PMID:25609862

Investigation on Main Radiation Source at Operation Floor of Fukushima Daiichi Nuclear Power Station Unit 4

NASA Astrophysics Data System (ADS)

Hirayama, Hideo; Kondo, Kenjiro; Suzuki, Seishiro; Hamamoto, Shimpei; Iwanaga, Kohei

2017-09-01

Pulse height distributions were measured using a LaBr3 detector set in a 1 cm lead collimator to investigate main radiation source at the operation floor of Fukushima Daiichi Nuclear Power Station Unit 4. It was confirmed that main radiation source above the reactor well was Co-60 from the activated steam dryer in the DS pool (Dryer-Separator pool) and that at the standby area was Cs-134 and Cs-137 from contaminated buildings and debris at the lower floor. Full energy peak count rate of Co-60 was reduced about 1/3 by 12mm lead sheet placed on the floor of the fuel handling machine.

Carding Machine Operator 8-27.77 -- Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Synthesis and identification of parameters of regenerative device for reversing link with increasing speed

NASA Astrophysics Data System (ADS)

Dubinin, N. N.; Mikhailichenko, S. A.; Goncharov, S. I.

2018-03-01

The article shows the problem of modeling the flow of fibrous suspension in the working bodies of mixing machines. A mathematical model describing the motion of a suspension with fibrous inclusions in a wet-type disintegrator, depending on the design of the accelerating unit and the operating device is obtained.

Machine Shop. Module 3: Bench Work and Material Science. Instructor's Guide.

ERIC Educational Resources Information Center

Walden, Charles H.; Nobles, Jack

This document consists of materials for an 11-unit course on the following topics: (1) hacksawing; (2) filing and deburring; (3) locating centers for drilling; (4) cutting threads with tap and die; (5) using a hand reamer; (6) pedestal/bench grinder operation; (7) whetting, polishing, and lapping; (8) screw, drill, and tap extraction; (9) arbor…

Development of a Low Cost 10kW Tubular SOFC Power System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bessette, Norman; Litka, Anthony; Rawson, Jolyon

The DOE program funded from 2003 through early 2013 has brought the Acumentrics SOFC program from an early stage R&D program to an entry level commercial product offering. The development work started as one of the main core teams under the DOE Solid State Energy Conversion Alliance (SECA) program administered by the National Energy Technology Laboratory (NETL) of the DOE. During the first phase of the program, lasting approximately 3-4 years, a 5kW machine was designed, manufactured and tested against the specification developed by NETL. This unit was also shipped to NETL for independent verification testing which validated all ofmore » the results achieved while in the laboratory at Acumentrics. The Acumentrics unit passed all criteria established from operational stability, efficiency, and cost projections. Passing of the SECA Phase I test allowed the program to move into Phase II of the program. During this phase, the overall objective was to further refine the unit meeting a higher level of performance stability as well as further cost reductions. During the first year of this new phase, the NETL SECA program was refocused towards larger size units and operation on coal gasification due to the severe rise in natural gas prices and refocus on the US supply of indigenous coal. At this point, the program was shifted to the U.S. DOE’s Energy Efficiency and Renewable Energy (EERE) division located in Golden, Colorado. With this shift, the focus remained on smaller power units operational on gaseous fuels for a variety of applications including micro combined heat and power (mCHP). To achieve this goal, further enhancements in power, life expectancy and reductions in cost were necessary. The past 5 years have achieved these goals with machines that can now achieve over 40% electrical efficiency and field units that have now operated for close to a year and a half with minimal maintenance. The following report details not only the first phase while under the SECA program and the key achievements but also the results while under EERE’s leadership and the transition to an early commercial product offering.« less

Alternator control for battery charging

DOEpatents

Brunstetter, Craig A.; Jaye, John R.; Tallarek, Glen E.; Adams, Joseph B.

2015-07-14

In accordance with an aspect of the present disclosure, an electrical system for an automotive vehicle has an electrical generating machine and a battery. A set point voltage, which sets an output voltage of the electrical generating machine, is set by an electronic control unit (ECU). The ECU selects one of a plurality of control modes for controlling the alternator based on an operating state of the vehicle as determined from vehicle operating parameters. The ECU selects a range for the set point voltage based on the selected control mode and then sets the set point voltage within the range based on feedback parameters for that control mode. In an aspect, the control modes include a trickle charge mode and battery charge current is the feedback parameter and the ECU controls the set point voltage within the range to maintain a predetermined battery charge current.

Combined Grinding and Drying of Biomass in One Operation Phase I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sokhansanj, S

2008-06-26

First American Scientific Corporation (FASC) has developed a unique and innovative grinder/dryer called KDS Micronex. The KS (Kinetic Disintegration System) combines two operations of grinding and drying into a single operation which reduces dependence on external heat input. The machine captures the heat of comminution and combines it will centrifugal forces to expedite moisture extraction from wet biomass. Because it uses mechanical forces rather than providing direct heat to perform the drying operation, it is a simpler machine and uses less energy than conventional grinding and drying operations which occur as two separate steps. The entire compact unit can bemore » transported on a flatbed trailer to the site where biomass is available. Hence, the KDS Micronex is a technology that enables inexpensive pretreatment of waste materials and biomass. A well prepared biomass can be used as feed, fuel or fertilizer instead of being discarded. Electricity and chemical feedstock produced from such biomass would displace the use of fossil fuels and no net greenhouse gas emissions would result from such bio-based operations. Organic fertilizers resulting from the KS Micronex grinding/drying process will be pathogen-free unlike raw animal manures. The feasibility tests on KS during Phase I showed that a prototype machine can be developed, field tested and the technology demonstrated for commercial applications. The present KDS machine can remove up to 400 kg/h of water from a wet feed material. Since biomass processors demand a finished product that is only 10% moist and most raw materials like corn stover, bagasse, layer manure, cow dung, and waste wood have moisture contents of the order of 50%, this water removal rate translates to a production rate of roughly half a ton per hour. this is too small for most processors who are unwilling to acquire multiple machines because of the added complexity to the feed and product removal systems. The economics suffer due to small production rates, because the labor costs are a much larger fraction of the production cost. The goal for further research and development work is to scale up the KDS technology incorporating findings from Phase I into a machine that has superior performance characteristics.« less

Variability in the skin exposure of machine operators exposed to cutting fluids.

PubMed

Wassenius, O; Järvholm, B; Engström, T; Lillienberg, L; Meding, B

1998-04-01

This study describes a new technique for measuring skin exposure to cutting fluids and evaluates the variability of skin exposure among machine operators performing cyclic (repetitive) work. The technique is based on video recording and subsequent analysis of the video tape by means of computer-synchronized video equipment. The time intervals at which the machine operator's hand was exposed to fluid were registered, and the total wet time of the skin was calculated by assuming different evaporation times for the fluid. The exposure of 12 operators with different work methods was analyzed in 6 different workshops, which included a range of machine types, from highly automated metal cutting machines (ie, actual cutting and chip removal machines) requiring operator supervision to conventional metal cutting machines, where the operator was required to maneuver the machine and manually exchange products. The relative wet time varied between 0% and 100%. A significant association between short cycle time and high relative wet time was noted. However, there was no relationship between the degree of automatization of the metal cutting machines and wet time. The study shows that skin exposure to cutting fluids can vary considerably between machine operators involved in manufacturing processes using different types of metal cutting machines. The machine type was not associated with dermal wetness. The technique appears to give objective information about dermal wetness.

76 FR 54800 - International Business Machines (IBM), Software Group Business Unit, Quality Assurance Group, San...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... Machines (IBM), Software Group Business Unit, Quality Assurance Group, San Jose, California; Notice of... workers of International Business Machines (IBM), Software Group Business Unit, Optim Data Studio Tools QA... February 2, 2011 (76 FR 5832). The subject worker group supplies acceptance testing services, design...

49 CFR 214.355 - Training and qualification in on-track safety for operators of roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... operators of roadway maintenance machines. 214.355 Section 214.355 Transportation Other Regulations Relating... operators of roadway maintenance machines. (a) The training and qualification of roadway workers who operate roadway maintenance machines shall include, as a minimum: (1) Procedures to prevent a person from being...

49 CFR 214.355 - Training and qualification in on-track safety for operators of roadway maintenance machines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... operators of roadway maintenance machines. 214.355 Section 214.355 Transportation Other Regulations Relating... operators of roadway maintenance machines. (a) The training and qualification of roadway workers who operate roadway maintenance machines shall include, as a minimum: (1) Procedures to prevent a person from being...

R&D of high reliable refrigeration system for superconducting generators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hosoya, T.; Shindo, S.; Yaguchi, H.

1996-12-31

Super-GM carries out R&D of 70 MW class superconducting generators (model machines), refrigeration system and superconducting wires to apply superconducting technology to electric power apparatuses. The helium refrigeration system for keeping field windings of superconducting generator (SCG) in cryogenic environment must meet the requirement of high reliability for uninterrupted long term operation of the SCG. In FY 1992, a high reliable conventional refrigeration system for the model machines was integrated by combining components such as compressor unit, higher temperature cold box and lower temperature cold box which were manufactured utilizing various fundamental technologies developed in early stage of the projectmore » since 1988. Since FY 1993, its performance tests have been carried out. It has been confirmed that its performance was fulfilled the development target of liquefaction capacity of 100 L/h and impurity removal in the helium gas to < 0.1 ppm. Furthermore, its operation method and performance were clarified to all different modes as how to control liquefaction rate and how to supply liquid helium from a dewar to the model machine. In addition, the authors have made performance tests and system performance analysis of oil free screw type and turbo type compressors which greatly improve reliability of conventional refrigeration systems. The operation performance and operational control method of the compressors has been clarified through the tests and analysis.« less

Method and system for fault accommodation of machines

NASA Technical Reports Server (NTRS)

Goebel, Kai Frank (Inventor); Subbu, Rajesh Venkat (Inventor); Rausch, Randal Thomas (Inventor); Frederick, Dean Kimball (Inventor)

2011-01-01

A method for multi-objective fault accommodation using predictive modeling is disclosed. The method includes using a simulated machine that simulates a faulted actual machine, and using a simulated controller that simulates an actual controller. A multi-objective optimization process is performed, based on specified control settings for the simulated controller and specified operational scenarios for the simulated machine controlled by the simulated controller, to generate a Pareto frontier-based solution space relating performance of the simulated machine to settings of the simulated controller, including adjustment to the operational scenarios to represent a fault condition of the simulated machine. Control settings of the actual controller are adjusted, represented by the simulated controller, for controlling the actual machine, represented by the simulated machine, in response to a fault condition of the actual machine, based on the Pareto frontier-based solution space, to maximize desirable operational conditions and minimize undesirable operational conditions while operating the actual machine in a region of the solution space defined by the Pareto frontier.

Aspects of image recognition in Vivid Technologies' dual-energy x-ray system for explosives detection

NASA Astrophysics Data System (ADS)

Eilbert, Richard F.; Krug, Kristoph D.

1993-04-01

The Vivid Rapid Explosives Detection Systems is a true dual energy x-ray machine employing precision x-ray data acquisition in combination with unique algorithms and massive computation capability. Data from the system's 960 detectors is digitally stored and processed by powerful supermicro-computers organized as an expandable array of parallel processors. The algorithms operate on the dual energy attenuation image data to recognize and define objects in the milieu of the baggage contents. Each object is then systematically examined for a match to a specific effective atomic number, density, and mass threshold. Material properties are determined by comparing the relative attenuations of the 75 kVp and 150 kVp beams and electronically separating the object from its local background. Other heuristic algorithms search for specific configurations and provide additional information. The machine automatically detects explosive materials and identifies bomb components in luggage with high specificity and throughput, X-ray dose is comparable to that of current airport x-ray machines. The machine is also configured to find heroin, cocaine, and US currency by selecting appropriate settings on-site. Since January 1992, production units have been operationally deployed at U.S. and European airports for improved screening of checked baggage.

Dose inspection and risk assessment on radiation safety for the use of non-medical X-ray machines in Taiwan

NASA Astrophysics Data System (ADS)

Hsu, Fang-Yuh; Hsu, Shih-Ming; Chao, Jiunn-Hsing

2017-11-01

The subject of this study is the on-site visits and inspections of facilities commissioned by the Atomic Energy Council (AEC) in Taiwan. This research was conducted to evaluate the possible dose and dose rate of cabinet-type X-ray equipment with nominal voltages of 30-150 kV and open-beam (portable or handheld) equipment, taking both normal operation and possibly abnormal operation conditions into account. Doses and dose rates were measured using a plastic scintillation survey meter and an electronic personal dosimeter. In total, 401 X-ray machines were inspected, including 139 units with nominal voltages of 30-50 kV X-ray equipment, 140 units with nominal voltages of 50-150 kV, and 122 open-beam (portable or handheld) X-ray equipment. The investigated doses for radiation workers and non-radiation workers operating cabinet-type X-ray equipment under normal safety conditions were all at the background dose level. Several investigated dose rates at the position of 10 cm away from the surface of open-beam (portable or handheld) X-ray equipment were very high, such X-ray machines are used by aeronautical police for the detection of suspected explosives, radiation workers are far away (at least 10 m away) from the X-ray machine during its operation. The doses per operation in X-ray equipment with a 30-50 kV nominal voltage were less than 1 mSv in all cases of abnormal use. Some doses were higher than 1 mSv per operation for X-ray equipment of 50-150 kV nominal voltage X-ray. The maximum dose rates at the beam exit have a very wide range, mostly less than 100 μSv/s and the largest value is about 3.92 mSv/s for open-beam (portable or handheld) X-ray devices. The risk induced by operating X-ray devices with nominal voltages of 30-50 kV is extremely low. The 11.5 mSv dose due to one operation at nominal voltage of 50-150 kV X-ray device is equivalent to the exposure of taking 575 chest X-rays. In the abnormal use of open-beam (portable or handheld) X-ray equipment, the effective dose of 3.92 mSv/s is equivalent to taking 196 chest radiographs within 1 s. This work assessed the annual doses (equivalent and effective doses) and risks of X-ray operator staff as reasonably as possible. The results of this research are helpful to the AEC (competent authority of ionization radiation) to improve the management and perform the safe control of X-ray equipment.

Industrial machine systems risk assessment: a critical review of concepts and methods.

PubMed

Etherton, John R

2007-02-01

Reducing the risk of work-related death and injury to machine operators and maintenance personnel poses a continuing occupational safety challenge. The risk of injury from machinery in U.S. workplaces is high. Between 1992 and 2001, there were, on average, 520 fatalities per year involving machines and, on average, 3.8 cases per 10,000 workers of nonfatal caught-in-running-machine injuries involving lost workdays. A U.S. task group recently developed a technical reference guideline, ANSI B11 TR3, "A Guide to Estimate, Evaluate, & Reduce Risks Associated with Machine Tools," that is intended to bring machine tool risk assessment practice in the United States up to or above the level now required by the international standard, ISO 14121. The ANSI guideline emphasizes identifying tasks and hazards not previously considered, particularly those associated with maintenance; and it further emphasizes teamwork among line workers, engineers, and safety professionals. The value of this critical review of concepts and methods resides in (1) its linking current risk theory to machine system risk assessment and (2) its exploration of how various risk estimation tools translate into risk-informed decisions on industrial machine system design and use. The review was undertaken to set the stage for a field evaluation study on machine risk assessment among users of the ANSI B11 TR3 method.

Prevalence and associated factors of work related musculoskeletal disorders among commercial milling machine operators in South-Eastern Nigerian markets.

PubMed

Ojukwu, Chidiebele Petronilla; Anyanwu, Godson Emeka; Nwabueze, Augustine Chijindu; Anekwu, Emelie Morris; Chukwu, Sylvester Caesar

2017-01-01

Milling machine operators perform physically demanding tasks that can lead to work related musculoskeletal disorders (WRMSDs), but literature on WRMSDs among milling machine operators is scarce. Knowledge of prevalence and risk factors of WRMSDs can be an appropriate base for planning and implementing ergonomics intervention programs in the workplace. This study aimed to determine the prevalence, pattern and associated factors of WRMSDs among commercial milling machine operators in Enugu, Nigeria. This cross-sectional survey involved 148 commercial milling machine operators (74 hand-operated milling machine operators (HOMMO) and 74 electrically-operated milling machine operators (EOMMO)), within the age range of 18-65 years, who were conveniently selected from four markets in Enugu, Nigeria. A standard Nordic questionnaire was used to assess the prevalence of WRMSDs among the participants. Data were summarized using descriptive statistics. There was a significant difference (p = 0.001) related to prevalence of WRMSDs between HOMMOs (77%) and EOMMOs (50%). All body parts were affected in both groups and shoulders (85.1%) and lower back (46%) had the highest percentage of prevalence. Working in awkward and same postures, working with injury, poor workplace design, repetition of tasks, vibratory working equipments, reduced rest, high job demand and heavy lifting were significantly associated with the prevalence of WRMSDs. WRMSDs are prevalent among commercial milling machine operators with higher occurrence in HOMMOs. Ergonomic interventions, including the re-design of milling machines and appropriate work posture education of machine operators are recommended in the milling industry.

Hands-free human-machine interaction with voice

NASA Astrophysics Data System (ADS)

Juang, B. H.

2004-05-01

Voice is natural communication interface between a human and a machine. The machine, when placed in today's communication networks, may be configured to provide automation to save substantial operating cost, as demonstrated in AT&T's VRCP (Voice Recognition Call Processing), or to facilitate intelligent services, such as virtual personal assistants, to enhance individual productivity. These intelligent services often need to be accessible anytime, anywhere (e.g., in cars when the user is in a hands-busy-eyes-busy situation or during meetings where constantly talking to a microphone is either undersirable or impossible), and thus call for advanced signal processing and automatic speech recognition techniques which support what we call ``hands-free'' human-machine communication. These techniques entail a broad spectrum of technical ideas, ranging from use of directional microphones and acoustic echo cancellatiion to robust speech recognition. In this talk, we highlight a number of key techniques that were developed for hands-free human-machine communication in the mid-1990s after Bell Labs became a unit of Lucent Technologies. A video clip will be played to demonstrate the accomplishement.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dehoff, Ryan R.; List, III, Frederick Alyious; Carver, Keith

ORNL Manufacturing Demonstration Facility worked with ECM Technologies LLC to investigate the use of precision electro-chemical machining technology to polish the surface of parts created by Arcam electron beam melting. The goals for phase one of this project have been met. The project goal was to determine whether electro-chemical machining is a viable method to improve the surface finish of Inconel 718 parts fabricated using the Arcam EBM method. The project partner (ECM) demonstrated viability for parts of both simple and complex geometry. During the course of the project, detailed process knowledge was generated. This project has resulted in themore » expansion of United States operations for ECM Technologies.« less

Machine-related injuries in the US mining industry and priorities for safety research.

PubMed

Ruff, Todd; Coleman, Patrick; Martini, Laura

2011-03-01

Researchers at the National Institute for Occupational Safety and Health studied mining accidents that involved a worker entangled in, struck by, or in contact with machinery or equipment in motion. The motivation for this study came from the large number of severe accidents, i.e. accidents resulting in a fatality or permanent disability, that are occurring despite available interventions. Accident descriptions were taken from an accident database maintained by the United States Department of Labor, Mine Safety and Health Administration, and 562 accidents that occurred during 2000-2007 fit the search criteria. Machine-related accidents accounted for 41% of all severe accidents in the mining industry during this period. Machinery most often involved in these accidents included conveyors, rock bolting machines, milling machines and haulage equipment such as trucks and loaders. The most common activities associated with these accidents were operation of the machine and maintenance and repair. The current methods to safeguard workers near machinery include mechanical guarding around moving components, lockout/tagout of machine power during maintenance and backup alarms for mobile equipment. To decrease accidents further, researchers recommend additional efforts in the development of new control technologies, training materials and dissemination of information on best practices.

Power Supply Changes for NSTX Resistive Wall Mode Coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramakrishnan, S S.

The National Spherical Torus Experiment (NSTX) has been designed and installed in the existing facilities at Princeton Plasma Physics Laboratory (PPPL). Most of the hardware, plant facilities, auxiliary sub-systems, and power systems originally used for the Tokamak Fusion Test Reactor (TFTR) have been used with suitable modifications to reflect NSTX needs. Prior to 2004, the NSTX power system was feeding twelve (12) circuits in the machine. In 2004 the Resistive Wall Mode (RWM) Coils were installed on the machine to correct error fields. There are six of these coils installed around the machine in the mid-plane. Since these coils needmore » fast and accurate controls, a Switching Power Amplifier (SPA) with three sub-units was procured, installed and commissioned along with other power loop components. Two RWM Coils were connected in series and fed from one SPA sub-unit. After the initial RWM campaign, operational requirements evolved such that each of the RWM coils now requires separate power and control. Hence a second SPA with three sub-units has been procured and installed. The second unit is of improved design and has the controls and power components completely isolated. The existing thyristor rectifier is used as DC Link to both of the Switching Power Amplifiers. The controls for the RWM are integrated into the overall computer control of the DC Power systems for NSTX. This paper describes the design changes in the RWM Power system for NSTX.« less

Performance Analysis of the NAS Y-MP Workload

NASA Technical Reports Server (NTRS)

Bergeron, Robert J.; Kutler, Paul (Technical Monitor)

1997-01-01

This paper describes the performance characteristics of the computational workloads on the NAS Cray Y-MP machines, a Y-MP 832 and later a Y-MP 8128. Hardware measurements indicated that the Y-MP workload performance matured over time, ultimately sustaining an average throughput of 0.8 GFLOPS and a vector operation fraction of 87%. The measurements also revealed an operation rate exceeding 1 per clock period, a well-balanced architecture featuring a strong utilization of vector functional units, and an efficient memory organization. Introduction of the larger memory 8128 increased throughput by allowing a more efficient utilization of CPUs. Throughput also depended on the metering of the batch queues; low-idle Saturday workloads required a buffer of small jobs to prevent memory starvation of the CPU. UNICOS required about 7% of total CPU time to service the 832 workloads; this overhead decreased to 5% for the 8128 workloads. While most of the system time went to service I/O requests, efficient scheduling prevented excessive idle due to I/O wait. System measurements disclosed no obvious bottlenecks in the response of the machine and UNICOS to the workloads. In most cases, Cray-provided software tools were- quite sufficient for measuring the performance of both the machine and operating, system.

Space shuttle orbiter auxiliary power unit development challenges

NASA Technical Reports Server (NTRS)

Lance, R.; Weary, D.

1985-01-01

When the flying spacecraft was approved for development, a power unit for the hydraulic system had to be developed. Unlike other systems on the orbiter, there was no precedent in earlier spacecraft for a hydraulic system nor for the power unit to drive the hydraulic pumps. The only prototypes available were airplane auxiliary power units (APU), which were not required to operate in the severe environments of a spacecraft nor to have the longevity of an orbiter hydraulic power unit. The challenge was to build a hydraulic power unit which could operate in 0g or 3g, in a vacuum or at sea level pressure, and at -65 F or 225 F, which would be capable of restarting while hot, and which would be capable of sustaining the hydraulic loads for the life of the orbiter. The basic approach to providing hydraulic power for the orbiter was to use a small, high speed, monopropellant fueled turbine power unit to drive a conventional aircraft type hydraulic pump. The stringent requirements imposed on the orbiter APU quickly made this machine different from existing aircraft APUs.

A consideration of the operation of automatic production machines.

PubMed

Hoshi, Toshiro; Sugimoto, Noboru

2015-01-01

At worksites, various automatic production machines are in use to release workers from muscular labor or labor in the detrimental environment. On the other hand, a large number of industrial accidents have been caused by automatic production machines. In view of this, this paper considers the operation of automatic production machines from the viewpoint of accident prevention, and points out two types of machine operation - operation for which quick performance is required (operation that is not permitted to be delayed) - and operation for which composed performance is required (operation that is not permitted to be performed in haste). These operations are distinguished by operation buttons of suitable colors and shapes. This paper shows that these characteristics are evaluated as "asymmetric on the time-axis". Here, in order for workers to accept the risk of automatic production machines, it is preconditioned in general that harm should be sufficiently small or avoidance of harm is easy. In this connection, this paper shows the possibility of facilitating the acceptance of the risk of automatic production machines by enhancing the asymmetric on the time-axis.

A consideration of the operation of automatic production machines

PubMed Central

HOSHI, Toshiro; SUGIMOTO, Noboru

2015-01-01

At worksites, various automatic production machines are in use to release workers from muscular labor or labor in the detrimental environment. On the other hand, a large number of industrial accidents have been caused by automatic production machines. In view of this, this paper considers the operation of automatic production machines from the viewpoint of accident prevention, and points out two types of machine operation − operation for which quick performance is required (operation that is not permitted to be delayed) − and operation for which composed performance is required (operation that is not permitted to be performed in haste). These operations are distinguished by operation buttons of suitable colors and shapes. This paper shows that these characteristics are evaluated as “asymmetric on the time-axis”. Here, in order for workers to accept the risk of automatic production machines, it is preconditioned in general that harm should be sufficiently small or avoidance of harm is easy. In this connection, this paper shows the possibility of facilitating the acceptance of the risk of automatic production machines by enhancing the asymmetric on the time-axis. PMID:25739898

Composite material impregnation unit

NASA Technical Reports Server (NTRS)

Wilkinson, S. P.; Marchello, J. M.; Johnston, N. J.

1993-01-01

This memorandum presents an introduction to the NASA multi-purpose prepregging unit which is now installed and fully operational at the Langley Research Center in the Polymeric Materials Branch. A description of the various impregnation methods that are available to the prepregger are presented. Machine operating details and protocol are provided for its various modes of operation. These include, where appropriate, the related equations for predicting the desired prepreg specifications. Also, as the prepregger is modular in its construction, each individual section is described and discussed. Safety concerns are an important factor and a chapter has been included that highlights the major safety features. Initial experiences and observations for fiber impregnation are described. These first observations have given great insight into the areas of future work that need to be addressed. Future memorandums will focus on these individual processes and their related problems.

The Critical Compression Load for a Universal Testing Machine When the Specimen Is Loaded Through Knife Edges

NASA Technical Reports Server (NTRS)

Lundquist, Eugene E; Schwartz, Edward B

1942-01-01

The results of a theoretical and experimental investigation to determine the critical compression load for a universal testing machine are presented for specimens loaded through knife edges. The critical load for the testing machine is the load at which one of the loading heads becomes laterally instable in relation to the other. For very short specimens the critical load was found to be less than the rated capacity given by the manufacturer for the machine. A load-length diagram is proposed for defining the safe limits of the test region for the machine. Although this report is particularly concerned with a universal testing machine of a certain type, the basic theory which led to the derivation of the general equation for the critical load, P (sub cr) = alpha L can be applied to any testing machine operated in compression where the specimen is loaded through knife edges. In this equation, L is the length of the specimen between knife edges and alpha is the force necessary to displace the upper end of the specimen unit horizontal distance relative to the lower end of the specimen in a direction normal to the knife edges through which the specimen is loaded.

Tricot-Knitting-Machine Operator (knit goods) 685.885--Technical Report on Development of USTES Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Blown Plastic Container Machine Operator (fabric. plastic prod.) 556.885--Technical Report on Development of USES Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

The Use of Skinnerian Teaching Machines and Programmed Instruction in the United States, 1960-1970.

ERIC Educational Resources Information Center

Casas, Martha

B.F. Skinner applied his concept of operant conditioning to education. Skinner believed that people acted the way they did because they had been reinforced for behaving in a certain manner. His orientation to pedagogy was predicated upon the notion that a student's behavior could be modified by guiding the student through the learning process…

Peeling-and-Coring-Machine Operator 529.886 -- Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Tube-Machine Operator (elec. equip.) 7-00.216--Technical Report on Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Braiding-Machine Operator (cot. small wares; textiles) 6-19.986--Standardization of the General Aptitude Test Battery.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Training and Employment Service.

The United States Training and Employment Service General Aptitude Test Battery (GATB), first published in 1947, has been included in a continuing program of research to validate the tests against success in many different occupations. The GATB consists of 12 tests which measure nine aptitudes: General Learning Ability; Verbal Aptitude; Numerical…

Hazard perception and occupational injuries in the welders and lathe machine operators of Rawalpindi and Islamabad.

PubMed

Shaikh, M A

2001-02-01

To study the prevalence of occupational injuries in the welders and lathe machine operators and their hazard perception. This study was conducted in the welders and lathe machine operators working in the welding and metal working shops in Rawalpindi and Islamabad. A cross-sectional survey was conducted by two trained health interviewers using uniform questionnaire with both close and open-ended questions. Two hundred and eight welders and 104 lathe machine operators were interviewed. Thirty nine (18.7%) welders and 27 (26%) lathe machine operators reported an injury in the past three months, while 63 (30.3%) welders and 76 (73.8%) lathe machine operators reported sustaining an injury in the past twelve months. However, only half of the welders and 31 (29.8%) lathe machine operators believed that their occupation was hazardous for health. For effective public health policy there is a need preventive education and enforcement of safety regulations for the informal occupational sector in Pakistan.

A study experiment of auto idle application in the excavator engine performance

NASA Astrophysics Data System (ADS)

Purwanto, Wawan; Maksum, Hasan; Putra, Dwi Sudarno; Azmi, Meri; Wahyudi, Retno

2016-03-01

The purpose of this study was to analyze the effect of applying auto idle to excavator engine performance, such as machine unitization and fuel consumption in Excavator. Steps to be done are to modify the system JA 44 and 67 in Vehicle Electronic Control Unit (V-ECU). The modifications will be obtained from the pattern of the engine speed. If the excavator attachment is not operated, the engine speed will return to the idle speed automatically. From the experiment results the auto idle reduces fuel consumption in excavator engine.

A study experiment of auto idle application in the excavator engine performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Purwanto, Wawan, E-mail: wawan5527@gmail.com; Maksum, Hasan; Putra, Dwi Sudarno, E-mail: dwisudarnoputra@ft.unp.ac.id

2016-03-29

The purpose of this study was to analyze the effect of applying auto idle to excavator engine performance, such as machine unitization and fuel consumption in Excavator. Steps to be done are to modify the system JA 44 and 67 in Vehicle Electronic Control Unit (V-ECU). The modifications will be obtained from the pattern of the engine speed. If the excavator attachment is not operated, the engine speed will return to the idle speed automatically. From the experiment results the auto idle reduces fuel consumption in excavator engine.

Operation of micro and molecular machines: a new concept with its origins in interface science.

PubMed

Ariga, Katsuhiko; Ishihara, Shinsuke; Izawa, Hironori; Xia, Hong; Hill, Jonathan P

2011-03-21

A landmark accomplishment of nanotechnology would be successful fabrication of ultrasmall machines that can work like tweezers, motors, or even computing devices. Now we must consider how operation of micro- and molecular machines might be implemented for a wide range of applications. If these machines function only under limited conditions and/or require specialized apparatus then they are useless for practical applications. Therefore, it is important to carefully consider the access of functionality of the molecular or nanoscale systems by conventional stimuli at the macroscopic level. In this perspective, we will outline the position of micro- and molecular machines in current science and technology. Most of these machines are operated by light irradiation, application of electrical or magnetic fields, chemical reactions, and thermal fluctuations, which cannot always be applied in remote machine operation. We also propose strategies for molecular machine operation using the most conventional of stimuli, that of macroscopic mechanical force, achieved through mechanical operation of molecular machines located at an air-water interface. The crucial roles of the characteristics of an interfacial environment, i.e. connection between macroscopic dimension and nanoscopic function, and contact of media with different dielectric natures, are also described.

Modeling of Particle Emission During Dry Orthogonal Cutting

NASA Astrophysics Data System (ADS)

Khettabi, Riad; Songmene, Victor; Zaghbani, Imed; Masounave, Jacques

2010-08-01

Because of the risks associated with exposure to metallic particles, efforts are being put into controlling and reducing them during the metal working process. Recent studies by the authors involved in this project have presented the effects of cutting speeds, workpiece material, and tool geometry on particle emission during dry machining; the authors have also proposed a new parameter, named the dust unit ( D u), for use in evaluating the quantity of particle emissions relative to the quantity of chips produced during a machining operation. In this study, a model for predicting the particle emission (dust unit) during orthogonal turning is proposed. This model, which is based on the energy approach combined with the microfriction and the plastic deformation of the material, takes into account the tool geometry, the properties of the worked material, the cutting conditions, and the chip segmentation. The model is validated using experimental results obtained during the orthogonal turning of 6061-T6 aluminum alloy, AISI 1018, AISI 4140 steels, and grey cast iron. A good agreement was found with experimental results. This model can help in designing strategies for reducing particle emission during machining processes, at the source.

[A new machinability test machine and the machinability of composite resins for core built-up].

PubMed

Iwasaki, N

2001-06-01

A new machinability test machine especially for dental materials was contrived. The purpose of this study was to evaluate the effects of grinding conditions on machinability of core built-up resins using this machine, and to confirm the relationship between machinability and other properties of composite resins. The experimental machinability test machine consisted of a dental air-turbine handpiece, a control weight unit, a driving unit of the stage fixing the test specimen, and so on. The machinability was evaluated as the change in volume after grinding using a diamond point. Five kinds of core built-up resins and human teeth were used in this study. The machinabilities of these composite resins increased with an increasing load during grinding, and decreased with repeated grinding. There was no obvious correlation between the machinability and Vickers' hardness; however, a negative correlation was observed between machinability and scratch width.

Prediction of Francis Turbine Prototype Part Load Pressure and Output Power Fluctuations with Hydroelectric Model

NASA Astrophysics Data System (ADS)

Alligné, S.; Nicolet, C.; Béguin, A.; Landry, C.; Gomes, J.; Avellan, F.

2017-04-01

The prediction of pressure and output power fluctuations amplitudes on Francis turbine prototype is a challenge for hydro-equipment industry since it is subjected to guarantees to ensure smooth and reliable operation of the hydro units. The European FP7 research project Hyperbole aims to setup a methodology to transpose the pressure fluctuations induced by the cavitation vortex rope from the reduced scale model to the prototype generating units. A Francis turbine unit of 444MW with a specific speed value of ν = 0.29, is considered as case study. A SIMSEN model of the power station including electrical system, controllers, rotating train and hydraulic system with transposed draft tube excitation sources is setup. Based on this model, a frequency analysis of the hydroelectric system is performed for all technologies to analyse potential interactions between hydraulic excitation sources and electrical components. Three technologies have been compared: the classical fixed speed configuration with Synchronous Machine (SM) and the two variable speed technologies which are Doubly Fed Induction Machine (DFIM) and Full Size Frequency Converter (FSFC).

Pre-use anesthesia machine check; certified anesthesia technician based quality improvement audit.

PubMed

Al Suhaibani, Mazen; Al Malki, Assaf; Al Dosary, Saad; Al Barmawi, Hanan; Pogoku, Mahdhav

2014-01-01

Quality assurance of providing a work ready machine in multiple theatre operating rooms in a tertiary modern medical center in Riyadh. The aim of the following study is to keep high quality environment for workers and patients in surgical operating rooms. Technicians based audit by using key performance indicators to assure inspection, passing test of machine worthiness for use daily and in between cases and in case of unexpected failure to provide quick replacement by ready to use another anesthetic machine. The anesthetic machines in all operating rooms are daily and continuously inspected and passed as ready by technicians and verified by anesthesiologist consultant or assistant consultant. The daily records of each machines were collected then inspected for data analysis by quality improvement committee department for descriptive analysis and report the degree of staff compliance to daily inspection as "met" items. Replaced machine during use and overall compliance. Distractive statistic using Microsoft Excel 2003 tables and graphs of sums and percentages of item studied in this audit. Audit obtained highest compliance percentage and low rate of replacement of machine which indicate unexpected machine state of use and quick machine switch. The authors are able to conclude that following regular inspection and running self-check recommended by the manufacturers can contribute to abort any possibility of hazard of anesthesia machine failure during operation. Furthermore in case of unexpected reason to replace the anesthesia machine in quick maneuver contributes to high assured operative utilization of man machine inter-phase in modern surgical operating rooms.

Precedent approach to the formation of programs for cyclic objects control

NASA Astrophysics Data System (ADS)

Kulakov, S. M.; Trofimov, V. B.; Dobrynin, A. S.; Taraborina, E. N.

2018-05-01

The idea and procedure for formalizing the precedent method of formation of complex control solutions (complex control programs) is discussed with respect to technological or organizational objects, the operation of which is organized cyclically. A typical functional structure of the system of precedent control by complex technological unit is developed, including a subsystem of retrospective optimization of actually implemented control programs. As an example, the problem of constructing replaceable planograms for the operation of the link of a heading-and-winning machine on the basis of precedents is considered.

Use of machine-learning classifiers to predict requests for preoperative acute pain service consultation.

PubMed

Tighe, Patrick J; Lucas, Stephen D; Edwards, David A; Boezaart, André P; Aytug, Haldun; Bihorac, Azra

2012-10-01

  The purpose of this project was to determine whether machine-learning classifiers could predict which patients would require a preoperative acute pain service (APS) consultation.   Retrospective cohort.   University teaching hospital.   The records of 9,860 surgical patients posted between January 1 and June 30, 2010 were reviewed.   Request for APS consultation. A cohort of machine-learning classifiers was compared according to its ability or inability to classify surgical cases as requiring a request for a preoperative APS consultation. Classifiers were then optimized utilizing ensemble techniques. Computational efficiency was measured with the central processing unit processing times required for model training. Classifiers were tested using the full feature set, as well as the reduced feature set that was optimized using a merit-based dimensional reduction strategy.   Machine-learning classifiers correctly predicted preoperative requests for APS consultations in 92.3% (95% confidence intervals [CI], 91.8-92.8) of all surgical cases. Bayesian methods yielded the highest area under the receiver operating curve (0.87, 95% CI 0.84-0.89) and lowest training times (0.0018 seconds, 95% CI, 0.0017-0.0019 for the NaiveBayesUpdateable algorithm). An ensemble of high-performing machine-learning classifiers did not yield a higher area under the receiver operating curve than its component classifiers. Dimensional reduction decreased the computational requirements for multiple classifiers, but did not adversely affect classification performance.   Using historical data, machine-learning classifiers can predict which surgical cases should prompt a preoperative request for an APS consultation. Dimensional reduction improved computational efficiency and preserved predictive performance. Wiley Periodicals, Inc.

The Knife Machine. Module 15.

ERIC Educational Resources Information Center

South Carolina State Dept. of Education, Columbia. Office of Vocational Education.

This module on the knife machine, one in a series dealing with industrial sewing machines, their attachments, and operation, covers one topic: performing special operations on the knife machine (a single needle or multi-needle machine which sews and cuts at the same time). These components are provided: an introduction, directions, an objective,…

A Delphi Study of Additive Manufacturing Applicability for United States Air Force Civil Engineer Contingency Operations

DTIC Science & Technology

2015-03-26

10 Table 2. Additive Manufacturing Categories (ASTM International , 2012) ..................... 14 Table 3. Delphi... flexibility in the design and structure of manufactured parts. It also allows for the creation of thousands of possible parts or tools from a single...machine. These benefits of 3 precision and flexibility in design and manufacturing show promising possibilities for addressing the general nature of

A new slash bundling concept for use in a Southern U.S

Treesearch

Steven Meadows; Tom Gallagher; Dana Mitchell

2011-01-01

John Deere’s biomass bundler unit is an effective machine for harvesting forest residues, which can be used as a source of fuelwood and/or a feedstock for biofuel production. This project explored an avenue that could supply a promising source of readily available energy in southeastern forested lands. Typical southern harvesting operations consist of whole-tree...

Enhancing understanding and improving prediction of severe weather through spatiotemporal relational learning.

PubMed

McGovern, Amy; Gagne, David J; Williams, John K; Brown, Rodger A; Basara, Jeffrey B

Severe weather, including tornadoes, thunderstorms, wind, and hail annually cause significant loss of life and property. We are developing spatiotemporal machine learning techniques that will enable meteorologists to improve the prediction of these events by improving their understanding of the fundamental causes of the phenomena and by building skillful empirical predictive models. In this paper, we present significant enhancements of our Spatiotemporal Relational Probability Trees that enable autonomous discovery of spatiotemporal relationships as well as learning with arbitrary shapes. We focus our evaluation on two real-world case studies using our technique: predicting tornadoes in Oklahoma and predicting aircraft turbulence in the United States. We also discuss how to evaluate success for a machine learning algorithm in the severe weather domain, which will enable new methods such as ours to transfer from research to operations, provide a set of lessons learned for embedded machine learning applications, and discuss how to field our technique.

Evaluation of the eZono 4000 with eZGuide for ultrasound-guided procedures.

PubMed

Gadsden, Jeff; Latmore, Malikah; Levine, Daniel M

2015-05-01

Ultrasound-guided procedures are increasingly common in a variety of acute care settings, such as the operating room, critical care unit and emergency room. However, accurate judgment of needle tip position using traditional ultrasound technology is frequently difficult, and serious injury can result from inadvertently advancing beyond or through the target. Needle navigation is a recent innovation that allows the clinician to visualize the needle position and trajectory in real time as it approaches the target. A novel ultrasound machine has recently been introduced that is portable and designed for procedural guidance. The eZono 4000™ features an innovative needle navigation technology that is simple to use and permits the use of a wide range of commercially available needles, avoiding the inconvenience and cost of proprietary equipment. This article discusses this new ultrasound machine in the context of other currently available ultrasound machines featuring needle navigation.

A Parallel Vector Machine for the PM Programming Language

NASA Astrophysics Data System (ADS)

Bellerby, Tim

2016-04-01

PM is a new programming language which aims to make the writing of computational geoscience models on parallel hardware accessible to scientists who are not themselves expert parallel programmers. It is based around the concept of communicating operators: language constructs that enable variables local to a single invocation of a parallelised loop to be viewed as if they were arrays spanning the entire loop domain. This mechanism enables different loop invocations (which may or may not be executing on different processors) to exchange information in a manner that extends the successful Communicating Sequential Processes idiom from single messages to collective communication. Communicating operators avoid the additional synchronisation mechanisms, such as atomic variables, required when programming using the Partitioned Global Address Space (PGAS) paradigm. Using a single loop invocation as the fundamental unit of concurrency enables PM to uniformly represent different levels of parallelism from vector operations through shared memory systems to distributed grids. This paper describes an implementation of PM based on a vectorised virtual machine. On a single processor node, concurrent operations are implemented using masked vector operations. Virtual machine instructions operate on vectors of values and may be unmasked, masked using a Boolean field, or masked using an array of active vector cell locations. Conditional structures (such as if-then-else or while statement implementations) calculate and apply masks to the operations they control. A shift in mask representation from Boolean to location-list occurs when active locations become sufficiently sparse. Parallel loops unfold data structures (or vectors of data structures for nested loops) into vectors of values that may additionally be distributed over multiple computational nodes and then split into micro-threads compatible with the size of the local cache. Inter-node communication is accomplished using standard OpenMP and MPI. Performance analyses of the PM vector machine, demonstrating its scaling properties with respect to domain size and the number of processor nodes will be presented for a range of hardware configurations. The PM software and language definition are being made available under unrestrictive MIT and Creative Commons Attribution licenses respectively: www.pm-lang.org.

A method to identify the main mode of machine tool under operating conditions

NASA Astrophysics Data System (ADS)

Wang, Daming; Pan, Yabing

2017-04-01

The identification of the modal parameters under experimental conditions is the most common procedure when solving the problem of machine tool structure vibration. However, the influence of each mode on the machine tool vibration in real working conditions remains unknown. In fact, the contributions each mode makes to the machine tool vibration during machining process are different. In this article, an active excitation modal analysis is applied to identify the modal parameters in operational condition, and the Operating Deflection Shapes (ODS) in frequencies of high level vibration that affect the quality of machining in real working conditions are obtained. Then, the ODS is decomposed by the mode shapes which are identified in operational conditions. So, the contributions each mode makes to machine tool vibration during machining process are got by decomposition coefficients. From the previous steps, we can find out the main modes which effect the machine tool more significantly in working conditions. This method was also verified to be effective by experiments.

Design Control Systems of Human Machine Interface in the NTVS-2894 Seat Grinder Machine to Increase the Productivity

NASA Astrophysics Data System (ADS)

Ardi, S.; Ardyansyah, D.

2018-02-01

In the Manufacturing of automotive spare parts, increased sales of vehicles is resulted in increased demand for production of engine valve of the customer. To meet customer demand, we carry out improvement and overhaul of the NTVS-2894 seat grinder machine on a machining line. NTVS-2894 seat grinder machine has been decreased machine productivity, the amount of trouble, and the amount of downtime. To overcome these problems on overhaul the NTVS-2984 seat grinder machine include mechanical and programs, is to do the design and manufacture of HMI (Human Machine Interface) GP-4501T program. Because of the time prior to the overhaul, NTVS-2894 seat grinder machine does not have a backup HMI (Human Machine Interface) program. The goal of the design and manufacture in this program is to improve the achievement of production, and allows an operator to operate beside it easier to troubleshoot the NTVS-2894 seat grinder machine thereby reducing downtime on the NTVS-2894 seat grinder machine. The results after the design are HMI program successfully made it back, machine productivity increased by 34.8%, the amount of trouble, and downtime decreased 40% decrease from 3,160 minutes to 1,700 minutes. The implication of our design, it could facilitate the operator in operating machine and the technician easer to maintain and do the troubleshooting the machine problems.

Research on ARM Numerical Control System

NASA Astrophysics Data System (ADS)

Wei, Xu; JiHong, Chen

Computerized Numerical Control (CNC) machine tools is the foundation of modern manufacturing systems, whose advanced digital technology is the key to solve the problem of sustainable development of machine tool manufacturing industry. The paper is to design CNC system embedded on ARM and indicates the hardware design and the software systems supported. On the hardware side: the driving chip of the motor control unit, as the core of components, is MCX314AL of DSP motion control which is developed by NOVA Electronics Co., Ltd. of Japan. It make convenient to control machine because of its excellent performance, simple interface, easy programming. On the Software side, the uC/OS-2 is selected as the embedded operating system of the open source, which makes a detailed breakdown of the modules of the CNC system. Those priorities are designed according to their actual requirements. The ways of communication between the module and the interrupt response are so different that it guarantees real-time property and reliability of the numerical control system. Therefore, it not only meets the requirements of the current social precision machining, but has good man-machine interface and network support to facilitate a variety of craftsmen use.

Dynamic modeling of brushless dc motors for aerospace actuation

NASA Technical Reports Server (NTRS)

Demerdash, N. A.; Nehl, T. W.

1980-01-01

A discrete time model for simulation of the dynamics of samarium cobalt-type permanent magnet brushless dc machines is presented. The simulation model includes modeling of the interaction between these machines and their attached power conditioners. These are transistorized conditioner units. This model is part of an overall discrete-time analysis of the dynamic performance of electromechanical actuators, which was conducted as part of prototype development of such actuators studied and built for NASA-Johnson Space Center as a prospective alternative to hydraulic actuators presently used in shuttle orbiter applications. The resulting numerical simulations of the various machine and power conditioner current and voltage waveforms gave excellent correlation to the actual waveforms collected from actual hardware experimental testing. These results, numerical and experimental, are presented here for machine motoring, regeneration and dynamic braking modes. Application of the resulting model to the determination of machine current and torque profiles during closed-loop actuator operation were also analyzed and the results are given here. These results are given in light of an overall view of the actuator system components. The applicability of this method of analysis to design optimization and trouble-shooting in such prototype development is also discussed in light of the results at hand.

Fuzzy logic controller optimization

DOEpatents

Sepe, Jr., Raymond B; Miller, John Michael

2004-03-23

A method is provided for optimizing a rotating induction machine system fuzzy logic controller. The fuzzy logic controller has at least one input and at least one output. Each input accepts a machine system operating parameter. Each output produces at least one machine system control parameter. The fuzzy logic controller generates each output based on at least one input and on fuzzy logic decision parameters. Optimization begins by obtaining a set of data relating each control parameter to at least one operating parameter for each machine operating region. A model is constructed for each machine operating region based on the machine operating region data obtained. The fuzzy logic controller is simulated with at least one created model in a feedback loop from a fuzzy logic output to a fuzzy logic input. Fuzzy logic decision parameters are optimized based on the simulation.

Man/Machine Interaction Dynamics And Performance (MMIDAP) capability

NASA Technical Reports Server (NTRS)

Frisch, Harold P.

1991-01-01

The creation of an ability to study interaction dynamics between a machine and its human operator can be approached from a myriad of directions. The Man/Machine Interaction Dynamics and Performance (MMIDAP) project seeks to create an ability to study the consequences of machine design alternatives relative to the performance of both machine and operator. The class of machines to which this study is directed includes those that require the intelligent physical exertions of a human operator. While Goddard's Flight Telerobotic's program was expected to be a major user, basic engineering design and biomedical applications reach far beyond telerobotics. Ongoing efforts are outlined of the GSFC and its University and small business collaborators to integrate both human performance and musculoskeletal data bases with analysis capabilities necessary to enable the study of dynamic actions, reactions, and performance of coupled machine/operator systems.

[Research on infrared safety protection system for machine tool].

PubMed

Zhang, Shuan-Ji; Zhang, Zhi-Ling; Yan, Hui-Ying; Wang, Song-De

2008-04-01

In order to ensure personal safety and prevent injury accident in machine tool operation, an infrared machine tool safety system was designed with infrared transmitting-receiving module, memory self-locked relay and voice recording-playing module. When the operator does not enter the danger area, the system has no response. Once the operator's whole or part of body enters the danger area and shades the infrared beam, the system will alarm and output an control signal to the machine tool executive element, and at the same time, the system makes the machine tool emergency stop to prevent equipment damaged and person injured. The system has a module framework, and has many advantages including safety, reliability, common use, circuit simplicity, maintenance convenience, low power consumption, low costs, working stability, easy debugging, vibration resistance and interference resistance. It is suitable for being installed and used in different machine tools such as punch machine, pour plastic machine, digital control machine, armor plate cutting machine, pipe bending machine, oil pressure machine etc.

10. Credit USAF, 1945. Original housed in the Muroc Flight ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. Credit USAF, 1945. Original housed in the Muroc Flight Test Base, Unit History, 1 September 1942 30 June 1945. Alfred F. Simpson Historical Research Agency. United States Air Force. Maxwell AFB, Alabama. View of jet engine rotor balancing machine with engine rotor in place for balancing operations. Original caption reads "Balancing bucket wheel of jet engine, Muroc Flight Test Base, Oct. 1945"; personnel not identified. Location where photograph was taken not determined, but presumed to be in shops of Building 4505. - Edwards Air Force Base, North Base, Hangar, End of North Base Road, Boron, Kern County, CA

Design and optimize of 3-axis filament winding machine

NASA Astrophysics Data System (ADS)

Quanjin, Ma; Rejab, M. R. M.; Idris, M. S.; Bachtiar, B.; Siregar, J. P.; Harith, M. N.

2017-10-01

Filament winding technique is developed as the primary process for composite cylindrical structures fabrication at low cost. Fibres are wound on a rotating mandrel by a filament winding machine where resin impregnated fibres pass through a pay-out eye. This paper aims to develop and optimize a 3-axis, lightweight, practical, efficient, portable filament winding machine to satisfy the customer demand, which can fabricate pipes and round shape cylinders with resins. There are 3 main units on the 3-axis filament winding machine, which are the rotary unit, the delivery unit and control system unit. Comparison with previous existing filament winding machines in the factory, it has 3 degrees of freedom and can fabricate more complex shape specimens based on the mandrel shape and particular control system. The machine has been designed and fabricated on 3 axes movements with control system. The x-axis is for movement of the carriage, the y-axis is the rotation of mandrel and the z-axis is the movement of the pay-out eye. Cylindrical specimens with different dimensions and winding angles were produced. 3-axis automated filament winding machine has been successfully designed with simple control system.

A Novel Application of Machine Learning Methods to Model Microcontroller Upset Due to Intentional Electromagnetic Interference

NASA Astrophysics Data System (ADS)

Bilalic, Rusmir

A novel application of support vector machines (SVMs), artificial neural networks (ANNs), and Gaussian processes (GPs) for machine learning (GPML) to model microcontroller unit (MCU) upset due to intentional electromagnetic interference (IEMI) is presented. In this approach, an MCU performs a counting operation (0-7) while electromagnetic interference in the form of a radio frequency (RF) pulse is direct-injected into the MCU clock line. Injection times with respect to the clock signal are the clock low, clock rising edge, clock high, and the clock falling edge periods in the clock window during which the MCU is performing initialization and executing the counting procedure. The intent is to cause disruption in the counting operation and model the probability of effect (PoE) using machine learning tools. Five experiments were executed as part of this research, each of which contained a set of 38,300 training points and 38,300 test points, for a total of 383,000 total points with the following experiment variables: injection times with respect to the clock signal, injected RF power, injected RF pulse width, and injected RF frequency. For the 191,500 training points, the average training error was 12.47%, while for the 191,500 test points the average test error was 14.85%, meaning that on average, the machine was able to predict MCU upset with an 85.15% accuracy. Leaving out the results for the worst-performing model (SVM with a linear kernel), the test prediction accuracy for the remaining machines is almost 89%. All three machine learning methods (ANNs, SVMs, and GPML) showed excellent and consistent results in their ability to model and predict the PoE on an MCU due to IEMI. The GP approach performed best during training with a 7.43% average training error, while the ANN technique was most accurate during the test with a 10.80% error.

30 CFR 48.27 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., drilling machine operators, haulage and conveyor systems operators, ground control machine operators, AMS... practice in the assigned tasks, and the performance of work duties at times or places where production is..., while under direct and immediate supervision and production is in progress, operation of the machine or...

30 CFR 48.27 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., drilling machine operators, haulage and conveyor systems operators, ground control machine operators, AMS... practice in the assigned tasks, and the performance of work duties at times or places where production is..., while under direct and immediate supervision and production is in progress, operation of the machine or...

30 CFR 48.27 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., drilling machine operators, haulage and conveyor systems operators, ground control machine operators, AMS... practice in the assigned tasks, and the performance of work duties at times or places where production is..., while under direct and immediate supervision and production is in progress, operation of the machine or...

30 CFR 48.27 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., drilling machine operators, haulage and conveyor systems operators, ground control machine operators, AMS... practice in the assigned tasks, and the performance of work duties at times or places where production is..., while under direct and immediate supervision and production is in progress, operation of the machine or...

Fine pitch thermosonic wire bonding: analysis of state-of-the-art manufacturing capability

NASA Astrophysics Data System (ADS)

Cavasin, Daniel

1995-09-01

A comprehensive process characterization was performed at the Motorola plastic package assembly site in Selangor, Malaysia, to document the current fine pitch wire bond process capability, using state-of-the-art equipment, in an actual manufacturing environment. Two machines, representing the latest technology from two separate manufacturers, were operated one shift per day for five days, bonding a 132 lead Plastic Quad Flat Pack. Using a test device specifically designed for fine pitch wire bonding, the bonding programs were alternated between 107 micrometers and 92 micrometers pad pitch, running each pitch for a total of 1600 units per machine. Wire, capillary type, and related materials were standardized and commercially available. A video metrology measurement system, with a demonstrated six sigma repeatability band width of 0.51 micrometers , was utilized to measure the bonded units for bond dimensions and placement. Standard Quality Assurance (QA) metrics were also performed. Results indicate that state-of-the-art thermosonic wire bonding can achieve acceptable assembly yields at these fine pad pitches.

Modelling daily dissolved oxygen concentration using least square support vector machine, multivariate adaptive regression splines and M5 model tree

NASA Astrophysics Data System (ADS)

Heddam, Salim; Kisi, Ozgur

2018-04-01

In the present study, three types of artificial intelligence techniques, least square support vector machine (LSSVM), multivariate adaptive regression splines (MARS) and M5 model tree (M5T) are applied for modeling daily dissolved oxygen (DO) concentration using several water quality variables as inputs. The DO concentration and water quality variables data from three stations operated by the United States Geological Survey (USGS) were used for developing the three models. The water quality data selected consisted of daily measured of water temperature (TE, °C), pH (std. unit), specific conductance (SC, μS/cm) and discharge (DI cfs), are used as inputs to the LSSVM, MARS and M5T models. The three models were applied for each station separately and compared to each other. According to the results obtained, it was found that: (i) the DO concentration could be successfully estimated using the three models and (ii) the best model among all others differs from one station to another.

Method and apparatus for monitoring machine performance

DOEpatents

Smith, Stephen F.; Castleberry, Kimberly N.

1996-01-01

Machine operating conditions can be monitored by analyzing, in either the time or frequency domain, the spectral components of the motor current. Changes in the electric background noise, induced by mechanical variations in the machine, are correlated to changes in the operating parameters of the machine.

Design of a large magnetic-bearing turbomolecular pump for NET

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernhardt, K.H.; Conrad, A.; Dinner, P.J.

1988-09-01

The feasibility of development of large vacuum components for operation in fusion machines have been investigated in the framework of the European Fusion Technology Programme. The requirements and the results of the feasibility study for the large turbomolecular pump units (TMP) are presented. Design parameters for single flow 50.000 l/s TMP and a double flow 15.000 and a 50.000 l/s TMP have been compared.

Distributed communications and control network for robotic mining

NASA Technical Reports Server (NTRS)

Schiffbauer, William H.

1989-01-01

The application of robotics to coal mining machines is one approach pursued to increase productivity while providing enhanced safety for the coal miner. Toward that end, a network composed of microcontrollers, computers, expert systems, real time operating systems, and a variety of program languages are being integrated that will act as the backbone for intelligent machine operation. Actual mining machines, including a few customized ones, have been given telerobotic semiautonomous capabilities by applying the described network. Control devices, intelligent sensors and computers onboard these machines are showing promise of achieving improved mining productivity and safety benefits. Current research using these machines involves navigation, multiple machine interaction, machine diagnostics, mineral detection, and graphical machine representation. Guidance sensors and systems employed include: sonar, laser rangers, gyroscopes, magnetometers, clinometers, and accelerometers. Information on the network of hardware/software and its implementation on mining machines are presented. Anticipated coal production operations using the network are discussed. A parallelism is also drawn between the direction of present day underground coal mining research to how the lunar soil (regolith) may be mined. A conceptual lunar mining operation that employs a distributed communication and control network is detailed.

Fun with Physics in the Elementary School.

ERIC Educational Resources Information Center

Ediger, Marlow

Primary grade pupils can become fascinated with simple machines. This paper suggests that teachers have simple machines in the classroom for a unit of study. It proposes some guidelines to create a unit of study for six simple machines that include the fulcrum, inclined plane, pulley, wheel and axle, wedge, and screw. Friction, gravity, force, and…

76 FR 5832 - International Business Machines (IBM), Software Group Business Unit, Optim Data Studio Tools QA...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-02

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,554] International Business Machines (IBM), Software Group Business Unit, Optim Data Studio Tools QA, San Jose, CA; Notice of... determination of the TAA petition filed on behalf of workers at International Business Machines (IBM), Software...

Machine Shop. Instructor Key. Supplementary Units.

ERIC Educational Resources Information Center

Walden, Charles; Cole, Phyllis

These supplementary units are designed to help students with special needs learn and apply machine shop skills. Nine competencies that are difficult for special needs students to grasp or that would help them get a future job in the field were chosen from the regular machine shop curriculum. Specific objectives for these competencies are listed at…

Specialized operating room for cesarean section in the perinatal care unit: a review of the opening process and operating room management.

PubMed

Kasagi, Yoshihiro; Okutani, Ryu; Oda, Yutaka

2015-02-01

We have opened an operating room in the perinatal care unit (PNCU), separate from our existing central operating rooms, to be used exclusively for cesarean sections. The purpose is to meet the increasing need for both emergency cesarean sections and non-obstetric surgeries. It is equipped with the same surgical instruments, anesthesia machine, monitoring system, rapid infusion system and airway devices as the central operating rooms. An anesthesiologist and a nurse from the central operating rooms trained the nurses working in the new operating room, and discussed solutions to numerous problems that arose before and after its opening. Currently most of the elective and emergency cesarean sections carried out during the daytime on weekdays are performed in the PNCU operating room. A total of 328 and 347 cesarean sections were performed in our hospital during 2011 and 2012, respectively, of which 192 (55.5 %) and 254 (73.2 %) were performed in the PNCU operating room. The mean occupancy rate of the central operating rooms also increased from 81 % in 2011 to 90 % in 2012. The PNCU operating room was built with the support of motivated personnel and multidisciplinary teamwork, and has been found to be beneficial for both surgeons and anesthesiologists, while it also contributes to hospital revenue.

75 FR 48955 - Arbitration Panel Decision Under the Randolph-Sheppard Act

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-12

... vending machine facility operated by a blind vendor at the USPS's Chicago Processing and Distribution... cafeteria operations are exempt from the Act and whether the vending machines operated by a private vendor at the Chicago Processing and Distribution Center are in direct competition with the vending machines...

Modal identification of spindle-tool unit in high-speed machining

NASA Astrophysics Data System (ADS)

Gagnol, Vincent; Le, Thien-Phu; Ray, Pascal

2011-10-01

The accurate knowledge of high-speed motorised spindle dynamic behaviour during machining is important in order to ensure the reliability of machine tools in service and the quality of machined parts. More specifically, the prediction of stable cutting regions, which is a critical requirement for high-speed milling operations, requires the accurate estimation of tool/holder/spindle set dynamic modal parameters. These estimations are generally obtained through Frequency Response Function (FRF) measurements of the non-rotating spindle. However, significant changes in modal parameters are expected to occur during operation, due to high-speed spindle rotation. The spindle's modal variations are highlighted through an integrated finite element model of the dynamic high-speed spindle-bearing system, taking into account rotor dynamics effects. The dependency of dynamic behaviour on speed range is then investigated and determined with accuracy. The objective of the proposed paper is to validate these numerical results through an experiment-based approach. Hence, an experimental setup is elaborated to measure rotating tool vibration during the machining operation in order to determine the spindle's modal frequency variation with respect to spindle speed in an industrial environment. The identification of natural frequencies of the spindle under rotating conditions is challenging, due to the low number of sensors and the presence of many harmonics in the measured signals. In order to overcome these issues and to extract the characteristics of the system, the spindle modes are determined through a 3-step procedure. First, spindle modes are highlighted using the Frequency Domain Decomposition (FDD) technique, with a new formulation at the considered rotating speed. These extracted modes are then analysed through the value of their respective damping ratios in order to separate the harmonics component from structural spindle natural frequencies. Finally, the stochastic properties of the modes are also investigated by considering the probability density of the retained modes. Results show a good correlation between numerical and experiment-based identified frequencies. The identified spindle-tool modal properties during machining allow the numerical model to be considered as representative of the real dynamic properties of the system.

30 CFR 70.220 - Status change reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... to all miners expected to wear a CPDM. The training shall be completed prior to a miner wearing a... cutting machine. On the cutting machine operator or on the cutting machine within 36 inches inby the normal working position; (2) Conventional section blasting off the solid. On the loading machine operator...

Electric motor-transformer aggregate in hermetic objects of transport vehicles

NASA Astrophysics Data System (ADS)

Zabora, Igor

2017-10-01

The construction and features of operation for new electrical unit - electric motor-transformer aggregate (DTA) are considered. Induction motors are intended for operation in hermetic plants with extreme conditions surrounding gas, steam-to-gas and liquid environment at a high temperature (to several hundred of degrees). Main objective of spent researches is the substantiation of possibility reliable and effective electric power transform with electric machine means directly in hermetic objects with extreme conditions environment by means of new DTA. The principle and job analysis of new disk induction motors of block-module type are observed.

Process improvement of knives production in a small scale industry

NASA Astrophysics Data System (ADS)

Ananto, Gamawan; Muktasim, Irfan

2017-06-01

Small scale industry that produces several kinds of knive should increase its capacity due to the demand from the market. Qualitatively, this case study consisted of formulating the problems, collecting and analyzing the necessary data, and determining the possible recommendations for the improvement. While the current capacity is only 9 (nine), it is expected that 20 units of knife will produced per month. The processes sequence are: profiling (a), truing (b), beveling (c), heat treatment (d), polishing (e), assembly (f), sharpening (g) and finishing (h). The first process (a) is held by out-house vendor company while other steps from (b) to (g) are executed by in-house vendor. However, there is a high dependency upon the high skilled operator who executes the in -house processes that are mostly held manually with several unbalance successive tasks, where the processing time of one or two tasks require longer duration than others since the operation is merely relied on the operator's skill. The idea is the improvement or change of the profiling and beveling process. Due to the poor surface quality and suboptimal hardness resulted from the laser cut machine for profiling, it is considered to subst itute this kind of process with wire cut that is capable to obtain good surface quality with certain range levels of roughness. Through simple cutting experiments on the samples, it is expected that the generated surface quality is adequate to omit the truing process (b). In addition, the cutting experiments on one, two, and four test samples resulted the shortest time that was obtained through four pieces in one cut. The technical parameters were set according to the recommendation of machine standard as referred to samples condition such as thickness and path length that affect ed the rate of wear. Meanwhile, in order to guarantee the uniformity of knife angles that are formed through beveling process (c), a grinding fixture was created. This kind of tool diminishes the dependency upon the operator's skill as well. The main conclusions are: the substitution of laser cut with wire cut machine for the first task (a) could reduce the operation time from 60 to 39.26 minutes with good result of surface quality and the truing process (b) could be omitted; the additional grinding fixture in beveling process (c) is required and two workstations have to be assigned instead of one as in previous condition. They lead to improvements including the guarantee of the uniformity of knifes' angle, the reduction on the operators' skills dependency, the shortening of cycle time from 855 to 420 minutes, and the higher number of productivity from 9 units/month into 20units/month.

An industrial sewing machine variable speed controller

NASA Technical Reports Server (NTRS)

Estes, Christa; Spiggle, Charles; Swift, Shannon; Vangeffen, Stephen; Youngner, Frank

1992-01-01

The apparel industry is attempting to move in a new direction in the coming decade. Since the invention of an electrically powered sewing machine, the operator has been seated. Today, companies are switching from a sit down operation to a stand up operation involving modular stations. The old treadle worked well with the sitting operator, but problems have been found when trying to use the same treadle with a standing operator. This report details a new design for a treadle to operate an industrial sewing machine that has a standing operator. Emphasis is placed on the ease of use by the operator, as well as the ergonomics involved. Procedures for testing the design are included along with possible uses for the treadle in other applications besides an industrial sewing machine.

An industrial sewing machine variable speed controller

NASA Astrophysics Data System (ADS)

Estes, Christa; Spiggle, Charles; Swift, Shannon; Vangeffen, Stephen; Youngner, Frank

The apparel industry is attempting to move in a new direction in the coming decade. Since the invention of an electrically powered sewing machine, the operator has been seated. Today, companies are switching from a sit down operation to a stand up operation involving modular stations. The old treadle worked well with the sitting operator, but problems have been found when trying to use the same treadle with a standing operator. This report details a new design for a treadle to operate an industrial sewing machine that has a standing operator. Emphasis is placed on the ease of use by the operator, as well as the ergonomics involved. Procedures for testing the design are included along with possible uses for the treadle in other applications besides an industrial sewing machine.

Control system for, and a method of, heating an operator station of a work machine

DOEpatents

Baker, Thomas M.; Hoff, Brian D.; Akasam, Sivaprasad

2005-04-05

There are situations in which an operator remains in an operator station of a work machine when an engine of the work machine is inactive. The present invention includes a control system for, and a method of, heating the operator station when the engine is inactive. A heating system of the work machine includes an electrically-powered coolant pump, a power source, and at least one piece of warmed machinery. An operator heat controller is moveable between a first and a second position, and is operable to connect the electrically-powered coolant pump to the power source when the engine is inactive and the operator heat controller is in the first position. Thus, by deactivating the engine and then moving the operator heat controller to the first position, the operator may supply electrical energy to the electrically-powered coolant pump, which is operably coupled to heat the operator station.

Hardware support for software controlled fast multiplexing of performance counters

DOEpatents

Salapura, Valentina; Wisniewski, Robert W

2013-10-01

Performance counters may be operable to collect one or more counts of one or more selected activities, and registers may be operable to store a set of performance counter configurations. A state machine may be operable to automatically select a register from the registers for reconfiguring the one or more performance counters in response to receiving a first signal. The state machine may be further operable to reconfigure the one or more performance counters based on a configuration specified in the selected register. The state machine yet further may be operable to copy data in selected one or more of the performance counters to a memory location, or to copy data from the memory location to the counters, in response to receiving a second signal. The state machine may be operable to store or restore the counter values and state machine configuration in response to a context switch event.

Hardware support for software controlled fast multiplexing of performance counters

DOEpatents

Salapura, Valentina; Wisniewski, Robert W.

2013-01-01

Performance counters may be operable to collect one or more counts of one or more selected activities, and registers may be operable to store a set of performance counter configurations. A state machine may be operable to automatically select a register from the registers for reconfiguring the one or more performance counters in response to receiving a first signal. The state machine may be further operable to reconfigure the one or more performance counters based on a configuration specified in the selected register. The state machine yet further may be operable to copy data in selected one or more of the performance counters to a memory location, or to copy data from the memory location to the counters, in response to receiving a second signal. The state machine may be operable to store or restore the counter values and state machine configuration in response to a context switch event.

Large robotized turning centers described

NASA Astrophysics Data System (ADS)

Kirsanov, V. V.; Tsarenko, V. I.

1985-09-01

The introduction of numerical control (NC) machine tools has made it possible to automate machining in series and small series production. The organization of automated production sections merged NC machine tools with automated transport systems. However, both the one and the other require the presence of an operative at the machine for low skilled operations. Industrial robots perform a number of auxiliary operations, such as equipment loading-unloading and control, changing cutting and auxiliary tools, controlling workpieces and parts, and cleaning of location surfaces. When used with a group of equipment they perform transfer operations between the machine tools. Industrial robots eliminate the need for workers to form auxiliary operations. This underscores the importance of developing robotized manufacturing centers providing for minimal human participation in production and creating conditions for two and three shift operation of equipment. Work carried out at several robotized manufacturing centers for series and small series production is described.

Learning Activity Packets for Grinding Machines. Unit I--Grinding Machines.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) is one of three that accompany the curriculum guide on grinding machines. It outlines the study activities and performance tasks for the first unit of this curriculum guide. Its purpose is to aid the student in attaining a working knowledge of this area of training and in achieving a skilled or moderately…

Performance analysis of single stage libr-water absorption machine operated by waste thermal energy of internal combustion engine: Case study

NASA Astrophysics Data System (ADS)

Sharif, Hafiz Zafar; Leman, A. M.; Muthuraman, S.; Salleh, Mohd Najib Mohd; Zakaria, Supaat

2017-09-01

Combined heating, cooling, and power is also known as Tri-generation. Tri-generation system can provide power, hot water, space heating and air -conditioning from single source of energy. The objective of this study is to propose a method to evaluate the characteristic and performance of a single stage lithium bromide-water (LiBr-H2O) absorption machine operated with waste thermal energy of internal combustion engine which is integral part of trigeneration system. Correlations for computer sensitivity analysis are developed in data fit software for (P-T-X), (H-T-X), saturated liquid (water), saturated vapor, saturation pressure and crystallization temperature curve of LiBr-H2O Solution. Number of equations were developed with data fit software and exported into excel work sheet for the evaluation of number of parameter concerned with the performance of vapor absorption machine such as co-efficient of performance, concentration of solution, mass flow rate, size of heat exchangers of the unit in relation to the generator, condenser, absorber and evaporator temperatures. Size of vapor absorption machine within its crystallization limits for cooling and heating by waste energy recovered from exhaust gas, and jacket water of internal combustion engine also presented in this study to save the time and cost for the facilities managers who are interested to utilize the waste thermal energy of their buildings or premises for heating and air conditioning applications.

Evaluating open-source cloud computing solutions for geosciences

NASA Astrophysics Data System (ADS)

Huang, Qunying; Yang, Chaowei; Liu, Kai; Xia, Jizhe; Xu, Chen; Li, Jing; Gui, Zhipeng; Sun, Min; Li, Zhenglong

2013-09-01

Many organizations start to adopt cloud computing for better utilizing computing resources by taking advantage of its scalability, cost reduction, and easy to access characteristics. Many private or community cloud computing platforms are being built using open-source cloud solutions. However, little has been done to systematically compare and evaluate the features and performance of open-source solutions in supporting Geosciences. This paper provides a comprehensive study of three open-source cloud solutions, including OpenNebula, Eucalyptus, and CloudStack. We compared a variety of features, capabilities, technologies and performances including: (1) general features and supported services for cloud resource creation and management, (2) advanced capabilities for networking and security, and (3) the performance of the cloud solutions in provisioning and operating the cloud resources as well as the performance of virtual machines initiated and managed by the cloud solutions in supporting selected geoscience applications. Our study found that: (1) no significant performance differences in central processing unit (CPU), memory and I/O of virtual machines created and managed by different solutions, (2) OpenNebula has the fastest internal network while both Eucalyptus and CloudStack have better virtual machine isolation and security strategies, (3) Cloudstack has the fastest operations in handling virtual machines, images, snapshots, volumes and networking, followed by OpenNebula, and (4) the selected cloud computing solutions are capable for supporting concurrent intensive web applications, computing intensive applications, and small-scale model simulations without intensive data communication.

Study of an Audio Playback Machine Storage, Distribution, and Repair System. Options for Machine Operation. Study II, Part 1, Phase 2, Final Report.

ERIC Educational Resources Information Center

ManTech Technical Services Corp., Fairfax, VA.

This report presents the results of a management study of audio playback equipment operations conducted by the National Library Service, Library of Congress, its associated network of state and local machine lending agencies (MLA), and other parties that play a role in current operations. The objectives were to document current operations,…

Alternative Models of Service, Centralized Machine Operations. Phase II Report. Volume II.

ERIC Educational Resources Information Center

Technology Management Corp., Alexandria, VA.

A study was conducted to determine if the centralization of playback machine operations for the national free library program would be feasible, economical, and desirable. An alternative model of playback machine services was constructed and compared with existing network operations considering both cost and service. The alternative model was…

Discomfort analysis in computerized numeric control machine operations.

PubMed

Muthukumar, Krishnamoorthy; Sankaranarayanasamy, Krishnasamy; Ganguli, Anindya Kumar

2012-06-01

The introduction of computerized numeric control (CNC) technology in manufacturing industries has revolutionized the production process, but there are some health and safety problems associated with these machines. The present study aimed to investigate the extent of postural discomfort in CNC machine operators, and the relationship of this discomfort to the display and control panel height, with a view to validate the anthropometric recommendation for the location of the display and control panel in CNC machines. The postural discomforts associated with CNC machines were studied in 122 male operators using Corlett and Bishop's body part discomfort mapping, subject information, and discomfort level at various time intervals from starting to end of a shift. This information was collected using a questionnaire. Statistical analysis was carried out using ANOVA. Neck discomfort due to the positioning of the machine displays, and shoulder and arm discomfort due to the positioning of controls were identified as common health issues in the operators of these machines. The study revealed that 45.9% of machine operators reported discomfort in the lower back, 41.8% in the neck, 22.1% in the upper-back, 53.3% in the shoulder and arm, and 21.3% of the operators reported discomfort in the leg. Discomfort increased with the progress of the day and was highest at the end of a shift; subject age had no effect on patient tendency to experience discomfort levels.

Discomfort Analysis in Computerized Numeric Control Machine Operations

PubMed Central

Sankaranarayanasamy, Krishnasamy; Ganguli, Anindya Kumar

2012-01-01

Objectives The introduction of computerized numeric control (CNC) technology in manufacturing industries has revolutionized the production process, but there are some health and safety problems associated with these machines. The present study aimed to investigate the extent of postural discomfort in CNC machine operators, and the relationship of this discomfort to the display and control panel height, with a view to validate the anthropometric recommendation for the location of the display and control panel in CNC machines. Methods The postural discomforts associated with CNC machines were studied in 122 male operators using Corlett and Bishop's body part discomfort mapping, subject information, and discomfort level at various time intervals from starting to end of a shift. This information was collected using a questionnaire. Statistical analysis was carried out using ANOVA. Results Neck discomfort due to the positioning of the machine displays, and shoulder and arm discomfort due to the positioning of controls were identified as common health issues in the operators of these machines. The study revealed that 45.9% of machine operators reported discomfort in the lower back, 41.8% in the neck, 22.1% in the upper-back, 53.3% in the shoulder and arm, and 21.3% of the operators reported discomfort in the leg. Conclusion Discomfort increased with the progress of the day and was highest at the end of a shift; subject age had no effect on patient tendency to experience discomfort levels. PMID:22993720

Translations on USSR Science and Technology, Physical Sciences and Technology, Number 16

DTIC Science & Technology

1977-08-05

34INVESTIGATION OF SPLITTING OF LIGHT NUCLEI WITH HIGH-ENERGY y -RAYS WITH THE METHOD OF WILSON’S CHAMBER OPERATING IN POWERFUL BEAMS OF ELECTRONIC...boast high reliability, high speed, and extremely modest power requirements. Information oh the Screen Visual display devices greatly facilitate...area of application of these units Includes navigation, control of power systems, machine tools, and manufac- turing processes. Th» ^»abilities of

10 CFR 431.295 - Units to be tested.

Code of Federal Regulations, 2011 CFR

2011-01-01

... EQUIPMENT Refrigerated Bottled or Canned Beverage Vending Machines Test Procedures § 431.295 Units to be tested. For each basic model of refrigerated bottled or canned beverage vending machine selected for...

MagLIF scaling on Z and future machines

NASA Astrophysics Data System (ADS)

Slutz, Stephen; Stygar, William; Gomez, Matthew; Campbell, Edward; Peterson, Kyle; Sefkow, Adam; Sinars, Daniel; Vesey, Roger

2015-11-01

The MagLIF (Magnetized Liner Inertial Fusion) concept [S.A. Slutz et al Phys. Plasmas 17, 056303, 2010] has demonstrated [M.R. Gomez et al., PRL 113, 155003, 2014] fusion-relevant plasma conditions on the Z machine. We present 2D numerical simulations of the scaling of MagLIF on Z indicating that deuterium/tritium (DT) fusion yields greater than 100 kJ could be possible on Z when operated at a peak current of 25 MA. Much higher yields are predicted for MagLIF driven with larger peak currents. Two high performance pulsed-power machines (Z300 and Z800) have been designed based on Linear Transformer Driver (LTD) technology. The Z300 design would provide approximately 48 MA to a MagLIF load, while Z800 would provide about 66 MA. We used a parameterized Thevenin equivalent circuit to drive a series of 1D and 2D numerical simulations with currents between and beyond these two designs. Our simulations indicate that 5-10 MJ yields may be possible with Z300, while yields of about 1 GJ may be possible with Z800. Sandia is a multiprogram laboratory operated by Sandia Corporation, a Lockheed Martin Company, for the United States Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Analysis of electric energy consumption of automatic milking systems in different configurations and operative conditions.

PubMed

Calcante, Aldo; Tangorra, Francesco M; Oberti, Roberto

2016-05-01

Automatic milking systems (AMS) have been a revolutionary innovation in dairy cow farming. Currently, more than 10,000 dairy cow farms worldwide use AMS to milk their cows. Electric consumption is one of the most relevant and uncontrollable operational cost of AMS, ranging between 35 and 40% of their total annual operational costs. The aim of the present study was to measure and analyze the electric energy consumption of 4 AMS with different configurations: single box, central unit featuring a central vacuum system for 1 cow unit and for 2 cow units. The electrical consumption (daily consumption, daily consumption per cow milked, consumption per milking, and consumption per 100L of milk) of each AMS (milking unit + air compressor) was measured using 2 energy analyzers. The measurement period lasted 24h with a sampling frequency of 0.2Hz. The daily total energy consumption (milking unit + air compressor) ranged between 45.4 and 81.3 kWh; the consumption per cow milked ranged between 0.59 and 0.99 kWh; the consumption per milking ranged between 0.21 and 0.33 kWh; and the consumption per 100L of milk ranged between 1.80 to 2.44 kWh according to the different configurations and operational contexts considered. Results showed that AMS electric consumption was mainly conditioned by farm management rather than machine characteristics/architectures. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Design and manufacture of the integrated field unit for the NIRSpec spectrometer on JWST

NASA Astrophysics Data System (ADS)

Lobb, Daniel; Robertson, David; Closs, Martin; Barnes, Andy

2008-09-01

The NIRSpec imaging spectrometer, which forms part of the James Webb Space Telescope instrumentation, will include an integrated field unit (IFU). The IFU will be tasked specifically with efficient analysis of extended objects, including galaxies; it will accept a square image area at the spectrometer entrance field, dissect this area into 30 parallel sub-slits, and image the sub-slits end-to-end, forming a single virtual entrance slit. The IFU, uses all-mirror optics to operate over the spectral range 700nm to 5000nm. 95 mirrors and the main support structure are made in a common aluminium alloy, to achieve athermal performance down to an operating temperature of around 30K. Relatively complex mirror surface shapes are produced by diamond machining. The IFU has been designed and constructed by SSTL, with optics produced by CfAI; the unit is currently undergoing performance tests. This paper describes the IFU optical design and performance, and outlines the mirror manufacturing methods and alignment procedures.

Transient performance of fan engine with water ingestion

NASA Technical Reports Server (NTRS)

Murthy, S. N. B.; Mullican, A.

1993-01-01

In a continuing investigation on developing and applying codes for prediction of performance of a turbine jet engine and its components with water ingestion during flight operation, including power settings, and flight altitudes and speed changes, an attempt was made to establish the effects of water ingestion through simulation of a generic high bypass ratio engine with a generic control. In view of the large effects arising in the air compression system and the prediffuser-combustor unit during water ingestion, attention was focused on those effects and the resulting changes in engine performance. Under all conditions of operation, whether ingestion is steady or not, it became evident that water ingestion causes a fan-compressor unit to operate in a time-dependent fashion with periodic features, particularly with respect to the state of water in the span and the film in the casing clearance space, at the exit of the machine. On the other hand, the aerodynamic performance of the unit may be considered as quasi-steady once the distribution of water has attained an equilibrium state with respect to its distribution and motion. For purposes of engine simulation, the performance maps for the generic fan-compressor unit were generated based on the attainment of a quasi-steady state (meaning steady except for long-period variations in performance) during ingestion and operation over a wide enough range of rotational speeds.

Measuring the usefulness of hidden units in Boltzmann machines with mutual information.

PubMed

Berglund, Mathias; Raiko, Tapani; Cho, Kyunghyun

2015-04-01

Restricted Boltzmann machines (RBMs) and deep Boltzmann machines (DBMs) are important models in deep learning, but it is often difficult to measure their performance in general, or measure the importance of individual hidden units in specific. We propose to use mutual information to measure the usefulness of individual hidden units in Boltzmann machines. The measure is fast to compute, and serves as an upper bound for the information the neuron can pass on, enabling detection of a particular kind of poor training results. We confirm experimentally that the proposed measure indicates how much the performance of the model drops when some of the units of an RBM are pruned away. We demonstrate the usefulness of the measure for early detection of poor training in DBMs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Efficacy of Code Optimization on Cache-based Processors

NASA Technical Reports Server (NTRS)

VanderWijngaart, Rob F.; Chancellor, Marisa K. (Technical Monitor)

1997-01-01

The current common wisdom in the U.S. is that the powerful, cost-effective supercomputers of tomorrow will be based on commodity (RISC) micro-processors with cache memories. Already, most distributed systems in the world use such hardware as building blocks. This shift away from vector supercomputers and towards cache-based systems has brought about a change in programming paradigm, even when ignoring issues of parallelism. Vector machines require inner-loop independence and regular, non-pathological memory strides (usually this means: non-power-of-two strides) to allow efficient vectorization of array operations. Cache-based systems require spatial and temporal locality of data, so that data once read from main memory and stored in high-speed cache memory is used optimally before being written back to main memory. This means that the most cache-friendly array operations are those that feature zero or unit stride, so that each unit of data read from main memory (a cache line) contains information for the next iteration in the loop. Moreover, loops ought to be 'fat', meaning that as many operations as possible are performed on cache data-provided instruction caches do not overflow and enough registers are available. If unit stride is not possible, for example because of some data dependency, then care must be taken to avoid pathological strides, just ads on vector computers. For cache-based systems the issues are more complex, due to the effects of associativity and of non-unit block (cache line) size. But there is more to the story. Most modern micro-processors are superscalar, which means that they can issue several (arithmetic) instructions per clock cycle, provided that there are enough independent instructions in the loop body. This is another argument for providing fat loop bodies. With these restrictions, it appears fairly straightforward to produce code that will run efficiently on any cache-based system. It can be argued that although some of the important computational algorithms employed at NASA Ames require different programming styles on vector machines and cache-based machines, respectively, neither architecture class appeared to be favored by particular algorithms in principle. Practice tells us that the situation is more complicated. This report presents observations and some analysis of performance tuning for cache-based systems. We point out several counterintuitive results that serve as a cautionary reminder that memory accesses are not the only factors that determine performance, and that within the class of cache-based systems, significant differences exist.

29 CFR 570.62 - Occupations involved in the operation of bakery machines (Order 11).

Code of Federal Regulations, 2010 CFR

2010-07-01

... dough mixer; batter mixer; bread dividing, rounding, or molding machine; dough brake; dough sheeter... cookie or cracker machine. (b) Exceptions. (1) This section shall not apply to the operation, including... as prohibited by § 570.61(a)(4). (2) This section shall not apply to the operation of pizza-dough...

29 CFR 570.55 - Occupations involved in the operation of power-driven woodworking machines (Order 5).

Code of Federal Regulations, 2011 CFR

2011-07-01

... woodworking machines (Order 5). 570.55 Section 570.55 Labor Regulations Relating to Labor (Continued) WAGE AND... woodworking machines (Order 5). (a) Finding and declaration of fact. The following occupations involved in the operation of power-driven wood-working machines are particularly hazardous for minors between 16 and 18...

Mobile machine hazardous working zone warning system

DOEpatents

Schiffbauer, William H.; Ganoe, Carl W.

1999-01-01

A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation thereof. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine.

Mobile machine hazardous working zone warning system

DOEpatents

Schiffbauer, W.H.; Ganoe, C.W.

1999-08-17

A warning system is provided for a mobile working machine to alert an individual of a potentially dangerous condition in the event the individual strays into a hazardous working zone of the machine. The warning system includes a transmitter mounted on the machine and operable to generate a uniform magnetic field projecting beyond an outer periphery of the machine in defining a hazardous working zone around the machine during operation. A receiver, carried by the individual and activated by the magnetic field, provides an alarm signal to alert the individual when he enters the hazardous working zone of the machine. 3 figs.

Advanced Motor Control Test Facility for NASA GRC Flywheel Energy Storage System Technology Development Unit

NASA Technical Reports Server (NTRS)

Kenny, Barbara H.; Kascak, Peter E.; Hofmann, Heath; Mackin, Michael; Santiago, Walter; Jansen, Ralph

2001-01-01

This paper describes the flywheel test facility developed at the NASA Glenn Research Center with particular emphasis on the motor drive components and control. A four-pole permanent magnet synchronous machine, suspended on magnetic bearings, is controlled with a field orientation algorithm. A discussion of the estimation of the rotor position and speed from a "once around signal" is given. The elimination of small dc currents by using a concurrent stationary frame current regulator is discussed and demonstrated. Initial experimental results are presented showing the successful operation and control of the unit at speeds up to 20,000 rpm.

GT200 getting better than 34% efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farmer, R.

1980-01-01

Design features are described for the GT200, a 50-Hz machine blend of high temperature advanced aircraft rotating components and heavy frame industrial gas turbine structure. It includes a twin spool as generator with a two-stage power turbine giving nominal performance of 85,000 kW ISO peak output with a 10,120 Btu per kW-h heat rate on LHV distillate. It is desgined for base, intermediate, or peak load operation simple or combined cycle. Stal-Laval in Sweden developed it and sold the first unit to the Swedish State Power Board in July 1977. The unit was installed at the Stallbocka Station.

Electromagnetic Signal Feedback Control for Proximity Detection Systems

NASA Astrophysics Data System (ADS)

Smith, Adam K.

Coal is the most abundant fossil fuel in the United States and remains an essential source of energy. While more than half of coal production comes from surface mining, nearly twice as many workers are employed by underground operations. One of the key pieces of equipment used in underground coal mining is the continuous mining machine. These large and powerful machines are operated in confined spaces by remote control. Since 1984, 40 mine workers in the U. S. have been killed when struck or pinned by a continuous mining machine. It is estimated that a majority of these accidents could have been prevented with the application of proximity detection systems. While proximity detection systems can significantly increase safety around a continuous mining machine, there are some system limitations. Commercially available proximity warning systems for continuous mining machines use magnetic field generators to detect workers and establish safe work areas around the machines. Several environmental factors, however, can influence and distort the magnetic fields. To minimize these effects, a control system has been developed using electromagnetic field strength and generator current to stabilize and control field drift induced by internal and external environmental factors. A laboratory test set-up was built using a ferrite-core magnetic field generator to produce a stable magnetic field. Previous work based on a field-invariant magnetic flux density model, which generically describes the electromagnetic field, is expanded upon. The analytically established transferable shell-based flux density distribution model is used to experimentally validate the control system. By controlling the current input to the ferrite-core generator, a more reliable and consistent magnetic field is produced. Implementation of this technology will improve accuracy and performance of existing commercial proximity detection systems. These research results will help reduce the risk of traumatic injuries and improve overall safety in the mining workplace.

The SED Machine: A Robotic Spectrograph for Fast Transient Classification

NASA Astrophysics Data System (ADS)

Blagorodnova, Nadejda; Neill, James D.; Walters, Richard; Kulkarni, Shrinivas R.; Fremling, Christoffer; Ben-Ami, Sagi; Dekany, Richard G.; Fucik, Jason R.; Konidaris, Nick; Nash, Reston; Ngeow, Chow-Choong; Ofek, Eran O.; O’ Sullivan, Donal; Quimby, Robert; Ritter, Andreas; Vyhmeister, Karl E.

2018-03-01

Current time domain facilities are finding several hundreds of transient astronomical events a year. The discovery rate is expected to increase in the future as soon as new surveys such as the Zwicky Transient Facility (ZTF) and the Large Synoptic Sky Survey (LSST) come online. Presently, the rate at which transients are classified is approximately one order or magnitude lower than the discovery rate, leading to an increasing “follow-up drought”. Existing telescopes with moderate aperture can help address this deficit when equipped with spectrographs optimized for spectral classification. Here, we provide an overview of the design, operations and first results of the Spectral Energy Distribution Machine (SEDM), operating on the Palomar 60-inch telescope (P60). The instrument is optimized for classification and high observing efficiency. It combines a low-resolution (R ∼ 100) integral field unit (IFU) spectrograph with “Rainbow Camera” (RC), a multi-band field acquisition camera which also serves as multi-band (ugri) photometer. The SEDM was commissioned during the operation of the intermediate Palomar Transient Factory (iPTF) and has already lived up to its promise. The success of the SEDM demonstrates the value of spectrographs optimized for spectral classification.

34 CFR 395.32 - Collection and distribution of vending machine income from vending machines on Federal property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... department, agency, or instrumentality of the United States, in accordance with established procedures of... each property managing department, agency or instrumentality of the United States, subject to the..., agencies, or instrumentalities of the United States, under which blind vendors or State licensing agencies...

29 CFR 570.55 - Occupations involved in the operation of power-driven woodworking machines (Order 5).

Code of Federal Regulations, 2010 CFR

2010-07-01

... woodworking machines (Order 5). 570.55 Section 570.55 Labor Regulations Relating to Labor (Continued) WAGE AND... woodworking machines (Order 5). Link to an amendment published at 75 FR 28455, May 20, 2010. (a) Finding and declaration of fact. The following occupations involved in the operation of power-driven wood-working machines...

Mississippi Curriculum Framework for Machine Tool Operation/Machine Shop and Tool and Die Making Technology Cluster (Program CIP: 48.0507--Tool and Die Maker/Technologist) (Program CIP: 48.0503--Machine Shop Assistant). Postsecondary Programs.

ERIC Educational Resources Information Center

Mississippi Research and Curriculum Unit for Vocational and Technical Education, State College.

This document, which is intended for use by community and junior colleges throughout Mississippi, contains curriculum frameworks for the course sequences in the machine tool operation/machine tool and tool and die making technology programs cluster. Presented in the introductory section are a framework of courses and programs, description of the…

10 CFR 431.292 - Definitions concerning refrigerated bottled or canned beverage vending machines.

Code of Federal Regulations, 2010 CFR

2010-01-01

... beverage vending machines. 431.292 Section 431.292 Energy DEPARTMENT OF ENERGY ENERGY CONSERVATION ENERGY... Vending Machines § 431.292 Definitions concerning refrigerated bottled or canned beverage vending machines. Basic model means, with respect to refrigerated bottled or canned beverage vending machines, all units...

High-performance dynamic quantum clustering on graphics processors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wittek, Peter, E-mail: peterwittek@acm.org

2013-01-15

Clustering methods in machine learning may benefit from borrowing metaphors from physics. Dynamic quantum clustering associates a Gaussian wave packet with the multidimensional data points and regards them as eigenfunctions of the Schroedinger equation. The clustering structure emerges by letting the system evolve and the visual nature of the algorithm has been shown to be useful in a range of applications. Furthermore, the method only uses matrix operations, which readily lend themselves to parallelization. In this paper, we develop an implementation on graphics hardware and investigate how this approach can accelerate the computations. We achieve a speedup of up tomore » two magnitudes over a multicore CPU implementation, which proves that quantum-like methods and acceleration by graphics processing units have a great relevance to machine learning.« less

Insights for the Third Offset: Addressing Challenges of Autonomy and Artificial Intelligence in Military Operations

DTIC Science & Technology

2017-09-01

third-offset/. 33 Sydney J . Freedberg Jr., “Carter, Roper Unveil Army’s New Ship-Killer Missile: ATACMS Upgrade,” Breaking Defense, October 28, 2016...39 For example, human-machine collaboration to improve the quality and speed of decision making. Sydney J . Freedberg Jr., “Centaur...unpublished thesis), United States Marine Corps Command and Staff College, 2000. 47 Stephen Anno and William E. Einspahr, “The Grenada Invasion,” in

ELECTROSTATIC ACCELERATORS (in French)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gerbier, R.

1962-04-01

The various methods presently in use for producing the continuous high voltage necessary for the operation of electrostatic accelerators are reviewed. The methods considered are voltage multiplier units (Greinacher and Morganstern types) and electrostatic instruments (Van de Graaff and Trump machines and Felici rotnting cylinder instruments). The electrostatic accelerators used at Grenoble which give currents of several milliamperes at voltages up to 1.2 Mv are described. In this energy region electron accelerators and neutron generators offer very interesting possibilities. (auth)

The Research and Implementation of MUSER CLEAN Algorithm Based on OpenCL

NASA Astrophysics Data System (ADS)

Feng, Y.; Chen, K.; Deng, H.; Wang, F.; Mei, Y.; Wei, S. L.; Dai, W.; Yang, Q. P.; Liu, Y. B.; Wu, J. P.

2017-03-01

It's urgent to carry out high-performance data processing with a single machine in the development of astronomical software. However, due to the different configuration of the machine, traditional programming techniques such as multi-threading, and CUDA (Compute Unified Device Architecture)+GPU (Graphic Processing Unit) have obvious limitations in portability and seamlessness between different operation systems. The OpenCL (Open Computing Language) used in the development of MUSER (MingantU SpEctral Radioheliograph) data processing system is introduced. And the Högbom CLEAN algorithm is re-implemented into parallel CLEAN algorithm by the Python language and PyOpenCL extended package. The experimental results show that the CLEAN algorithm based on OpenCL has approximately equally operating efficiency compared with the former CLEAN algorithm based on CUDA. More important, the data processing in merely CPU (Central Processing Unit) environment of this system can also achieve high performance, which has solved the problem of environmental dependence of CUDA+GPU. Overall, the research improves the adaptability of the system with emphasis on performance of MUSER image clean computing. In the meanwhile, the realization of OpenCL in MUSER proves its availability in scientific data processing. In view of the high-performance computing features of OpenCL in heterogeneous environment, it will probably become the preferred technology in the future high-performance astronomical software development.

The Photon Shell Game and the Quantum von Neumann Architecture with Superconducting Circuits

NASA Astrophysics Data System (ADS)

Mariantoni, Matteo

2012-02-01

Superconducting quantum circuits have made significant advances over the past decade, allowing more complex and integrated circuits that perform with good fidelity. We have recently implemented a machine comprising seven quantum channels, with three superconducting resonators, two phase qubits, and two zeroing registers. I will explain the design and operation of this machine, first showing how a single microwave photon | 1 > can be prepared in one resonator and coherently transferred between the three resonators. I will also show how more exotic states such as double photon states | 2 > and superposition states | 0 >+ | 1 > can be shuffled among the resonators as well [1]. I will then demonstrate how this machine can be used as the quantum-mechanical analog of the von Neumann computer architecture, which for a classical computer comprises a central processing unit and a memory holding both instructions and data. The quantum version comprises a quantum central processing unit (quCPU) that exchanges data with a quantum random-access memory (quRAM) integrated on one chip, with instructions stored on a classical computer. I will also present a proof-of-concept demonstration of a code that involves all seven quantum elements: (1), Preparing an entangled state in the quCPU, (2), writing it to the quRAM, (3), preparing a second state in the quCPU, (4), zeroing it, and, (5), reading out the first state stored in the quRAM [2]. Finally, I will demonstrate that the quantum von Neumann machine provides one unit cell of a two-dimensional qubit-resonator array that can be used for surface code quantum computing. This will allow the realization of a scalable, fault-tolerant quantum processor with the most forgiving error rates to date. [4pt] [1] M. Mariantoni et al., Nature Physics 7, 287-293 (2011.)[0pt] [2] M. Mariantoni et al., Science 334, 61-65 (2011).

Development of a wearable measurement and control unit for personal customizing machine-supported exercise.

PubMed

Wang, Zhihui; Tamura, Naoki; Kiryu, Tohru

2005-01-01

Wearable technology has been used in various health-related fields to develop advanced monitoring solutions. However, the monitoring function alone cannot meet all the requirements of personal customizing machine-supported exercise that have biosignal-based controls. In this paper, we propose a new wearable unit design equipped with measurement and control functions to support the personal customization process. The wearable unit can measure the heart rate and electromyogram signals during exercise and output workload control commands to the exercise machines. We then applied a prototype of the wearable unit to an Internet-based cycle ergometer system. The wearable unit was examined using twelve young people to check its feasibility. The results verified that the unit could successfully adapt to the control of the workload and was effective for continuously supporting gradual changes in physical activities.

The Body of Knowledge & Content Framework. Identifying the Important Knowledge Required for Productive Performance of a Plastics Machine Operator. Blow Molding, Extrusion, Injection Molding, Thermoforming.

ERIC Educational Resources Information Center

Society of the Plastics Industry, Inc., Washington, DC.

Designed to guide training and curriculum development to prepare machine operators for the national certification exam, this publication identifies the important knowledge required for productive performance by a plastics machine operator. Introductory material discusses the rationale for a national standard, uses of the Body of Knowledge,…

Review of the energy check of an electron-only linear accelerator over a 6 year period: sensitivity of the technique to energy shift.

PubMed

Biggs, Peter J

2003-04-01

The calibration and monthly QA of an electron-only linear accelerator dedicated to intra-operative radiation therapy has been reviewed. Since this machine is calibrated prior to every procedure, there was no necessity to adjust the output calibration at any time except, perhaps, when the magnetron is changed, provided the machine output is reasonably stable. This gives a unique opportunity to study the dose output of the machine per monitor unit, variation in the timer error, flatness and symmetry of the beam and the energy check as a function of time. The results show that, although the dose per monitor unit varied within +/- 2%, the timer error within +/- 0.005 MU and the asymmetry within 1-2%, none of these parameters showed any systematic change with time. On the other hand, the energy check showed a linear drift with time for 6, 9, and 12 MeV (2.1, 3.5, and 2.5%, respectively, over 5 years), while at 15 and 18 MeV, the energy check was relatively constant. It is further shown that based on annual calibrations and RPC TLD checks, the energy of each beam is constant and that therefore the energy check is an exquisitely sensitive one. The consistency of the independent checks is demonstrated.

Development of an Organic Rankine Cycle system for exhaust energy recovery in internal combustion engines

NASA Astrophysics Data System (ADS)

Cipollone, Roberto; Bianchi, Giuseppe; Gualtieri, Angelo; Di Battista, Davide; Mauriello, Marco; Fatigati, Fabio

2015-11-01

Road transportation is currently one of the most influencing sectors for global energy consumptions and CO2 emissions. Nevertheless, more than one third of the fuel energy supplied to internal combustion engines is still rejected to the environment as thermal waste at the exhaust. Therefore, a greater fuel economy might be achieved recovering the energy from exhaust gases and converting it into useful power on board. In the current research activity, an ORC-based energy recovery system was developed and coupled with a diesel engine. The innovative feature of the recovery power unit relies upon the usage of sliding vane rotary machines as pump and expander. After a preliminary exhaust gas mapping, which allowed to assess the magnitude of the thermal power to be recovered, a thermodynamic analysis was carried out to design the ORC system and the sliding vane machines using R236fa as working fluid. An experimental campaign was eventually performed at different operating regimes according to the ESC procedure and investigated the recovery potential of the power unit at design and off-design conditions. Mechanical power recovered ranged from 0.7 kW up to 1.9 kW, with an overall cycle efficiency from 3.8% up to 4.8% respectively. These results candidate sliding vane machines as efficient and reliable devices for waste heat recovery applications.

Cluster: Metals. Course: Machine Shop. Research Project.

ERIC Educational Resources Information Center

Sanford - Lee County Schools, NC.

The set of 13 units is designed for use with an instructor in actual machine shop practice and is also keyed to audio visual and textual materials. Each unit contains a series of task packages which: specify prerequisites within the series (minimum is Unit 1); provide a narrative rationale for learning; list both general and specific objectives in…

21 CFR 870.4220 - Cardiopulmonary bypass heart-lung machine console.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Cardiopulmonary bypass heart-lung machine console... Cardiopulmonary bypass heart-lung machine console. (a) Identification. A cardiopulmonary bypass heart-lung machine... heart-lung machine. The console is designed to interface with the basic units used in a gas exchange...

21 CFR 870.4220 - Cardiopulmonary bypass heart-lung machine console.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Cardiopulmonary bypass heart-lung machine console... Cardiopulmonary bypass heart-lung machine console. (a) Identification. A cardiopulmonary bypass heart-lung machine... heart-lung machine. The console is designed to interface with the basic units used in a gas exchange...

21 CFR 870.4220 - Cardiopulmonary bypass heart-lung machine console.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Cardiopulmonary bypass heart-lung machine console... Cardiopulmonary bypass heart-lung machine console. (a) Identification. A cardiopulmonary bypass heart-lung machine... heart-lung machine. The console is designed to interface with the basic units used in a gas exchange...

21 CFR 870.4220 - Cardiopulmonary bypass heart-lung machine console.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Cardiopulmonary bypass heart-lung machine console... Cardiopulmonary bypass heart-lung machine console. (a) Identification. A cardiopulmonary bypass heart-lung machine... heart-lung machine. The console is designed to interface with the basic units used in a gas exchange...

21 CFR 870.4220 - Cardiopulmonary bypass heart-lung machine console.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Cardiopulmonary bypass heart-lung machine console... Cardiopulmonary bypass heart-lung machine console. (a) Identification. A cardiopulmonary bypass heart-lung machine... heart-lung machine. The console is designed to interface with the basic units used in a gas exchange...

National Machine Guarding Program: Part 1. Machine safeguarding practices in small metal fabrication businesses.

PubMed

Parker, David L; Yamin, Samuel C; Brosseau, Lisa M; Xi, Min; Gordon, Robert; Most, Ivan G; Stanley, Rodney

2015-11-01

Metal fabrication workers experience high rates of traumatic occupational injuries. Machine operators in particular face high risks, often stemming from the absence or improper use of machine safeguarding or the failure to implement lockout procedures. The National Machine Guarding Program (NMGP) was a translational research initiative implemented in conjunction with two workers' compensation insures. Insurance safety consultants trained in machine guarding used standardized checklists to conduct a baseline inspection of machine-related hazards in 221 business. Safeguards at the point of operation were missing or inadequate on 33% of machines. Safeguards for other mechanical hazards were missing on 28% of machines. Older machines were both widely used and less likely than newer machines to be properly guarded. Lockout/tagout procedures were posted at only 9% of machine workstations. The NMGP demonstrates a need for improvement in many aspects of machine safety and lockout in small metal fabrication businesses. © 2015 The Authors. American Journal of Industrial Medicine published by Wiley Periodicals, Inc.

Methods, systems and apparatus for controlling operation of two alternating current (AC) machines

DOEpatents

Gallegos-Lopez, Gabriel [Torrance, CA; Nagashima, James M [Cerritos, CA; Perisic, Milun [Torrance, CA; Hiti, Silva [Redondo Beach, CA

2012-06-05

A system is provided for controlling two alternating current (AC) machines via a five-phase PWM inverter module. The system comprises a first control loop, a second control loop, and a current command adjustment module. The current command adjustment module operates in conjunction with the first control loop and the second control loop to continuously adjust current command signals that control the first AC machine and the second AC machine such that they share the input voltage available to them without compromising the target mechanical output power of either machine. This way, even when the phase voltage available to either one of the machines decreases, that machine outputs its target mechanical output power.

Switching Circuit for Shop Vacuum System

NASA Technical Reports Server (NTRS)

Burley, R. K.

1987-01-01

No internal connections to machine tools required. Switching circuit controls vacuum system draws debris from grinders and sanders in machine shop. Circuit automatically turns on vacuum system whenever at least one sander or grinder operating. Debris safely removed, even when operator neglects to turn on vacuum system manually. Pickup coils sense alternating magnetic fields just outside operating machines. Signal from any coil or combination of coils causes vacuum system to be turned on.

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2014 CFR

2014-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor systems operators, roof and ground control machine operators, and those in blasting operations shall not... duties at times or places where production is not the primary objective; on (ii) Supervised operation...

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2012 CFR

2012-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor systems operators, roof and ground control machine operators, and those in blasting operations shall not... duties at times or places where production is not the primary objective; on (ii) Supervised operation...

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2011 CFR

2011-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor systems operators, roof and ground control machine operators, and those in blasting operations shall not... duties at times or places where production is not the primary objective; on (ii) Supervised operation...

30 CFR 48.7 - Training of miners assigned to a task in which they have had no previous experience; minimum...

Code of Federal Regulations, 2013 CFR

2013-07-01

... to new work tasks as mobile equipment operators, drilling machine operators, haulage and conveyor systems operators, roof and ground control machine operators, and those in blasting operations shall not... duties at times or places where production is not the primary objective; on (ii) Supervised operation...

Modelling of a mecanum wheel taking into account the geometry of road rollers

NASA Astrophysics Data System (ADS)

Hryniewicz, P.; Gwiazda, A.; Banaś, W.; Sękala, A.; Foit, K.

2017-08-01

During the process planning in a company one of the basic factors associated with the production costs is the operation time for particular technological jobs. The operation time consists of time units associated with the machining tasks of a workpiece as well as the time associated with loading and unloading and the transport operations of this workpiece between machining stands. Full automation of manufacturing in industry companies tends to a maximal reduction in machine downtimes, thereby the fixed costs simultaneously decreasing. The new construction of wheeled vehicles, using Mecanum wheels, reduces the transport time of materials and workpieces between machining stands. These vehicles have the ability to simultaneously move in two axes and thus more rapid positioning of the vehicle relative to the machining stand. The Mecanum wheel construction implies placing, around the wheel free rollers that are mounted at an angle 450, which allow the movement of the vehicle not only in its axis but also perpendicular thereto. The improper selection of the rollers can cause unwanted vertical movement of the vehicle, which may cause difficulty in positioning of the vehicle in relation to the machining stand and the need for stabilisation. Hence the proper design of the free rollers is essential in designing the whole Mecanum wheel construction. It allows avoiding the disadvantageous and unwanted vertical vibrations of a whole vehicle with these wheels. In the article the process of modelling the free rollers, in order to obtain the desired shape of unchanging, horizontal trajectory of the vehicle is presented. This shape depends on the desired diameter of the whole Mecanum wheel, together with the road rollers, and the width of the drive wheel. Another factor related with the curvature of the trajectory shape is the length of the road roller and its diameter decreases depending on the position with respect to its centre. The additional factor, limiting construction of the road rollers, is their bearings. Depending on the load, carried by the vehicle and the rotational speed of the drive wheel, the bearings themselves can greatly affect the diameter of the rollers and the whole Mecanum wheels. The solution of this problem is presented in the paper. It is illustrated with virtual models elaborated in advanced program of the CAE class.

49 CFR 214.503 - Good-faith challenges; procedures for notification and resolution.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Roadway Maintenance Machines and Hi-Rail Vehicles § 214.503 Good-faith challenges; procedures for notification and resolution. (a) An employee operating an on-track roadway maintenance machine or hi-rail.... (b) Any employee charged with operating an on-track roadway maintenance machine or hi-rail vehicle...

77 FR 4288 - Arbitration Panel Decision Under the Randolph-Sheppard Act

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-27

... February 5, 2009, permit application to operate vending machines at the Southern Oregon Rehabilitation... Blind for a permit to operate the Clinic vending machines.'' Arbitration Panel Decision After reviewing... vending machines are part and parcel of that facility. The panel noted that the parties' differing...

Ergonomic risk factor identification for sewing machine operators through supervised occupational therapy fieldwork in Bangladesh: A case study.

PubMed

Habib, Md Monjurul

2015-01-01

Many sewing machine operators are working with high risk factors for musculoskeletal health in the garments industries in Bangladesh. To identify the physical risk factors among sewing machine operators in a Bangladeshi garments factory. Sewing machine operators (327, 83% female), were evaluated. The mean age of the participants was 25.25 years. Six ergonomic risk factors were determined using the Musculoskeletal Disorders risk assessment. Data collection included measurements of sewing machine table and chair heights; this data was combined with information from informal interviews. Significant ergonomic risk factors found included the combination of awkward postures of the neck and back, repetitive hand and arm movements, poor ergonomic workstations and prolonged working hours without adequate breaks; these risk factors resulted in musculoskeletal complaints, sick leave, and switching jobs. One aspect of improving worker health in garment factories includes addressing musculoskeletal risk factors through ergonomic interventions.

Characteristics and treatability of oil-bearing wastes from aluminum alloy machining operations.

PubMed

Chen, Luke; Hsieh, Chueh-Chen; Wetherbee, John; Yang, Chen-Lu

2008-04-15

Enomoto Industry Co., exclusively uses water-based cutting fluids in its aluminum alloy machining operations. Since the cost of disposal can be much greater than the cost of purchase, the treatability of spent cutting fluids is becoming a major criterion for cutting fluid selection. Samples were collected from the machining lines at Enomoto's facility to determine their characteristics and evaluate their treatability with centrifugation, chemical coagulation and electrochemical coagulation. As expected, oil and grease (O&G) and total suspended solids (TSS) are the main reasons that spent cutting fluids are prohibited from being discharged into local swage systems. The average O&G found in the spent cutting fluids is 87,354 mg/L with TSS of more than 70,000 mg/L. Both O&G and TSS are the major contributors to the high turbidity of these waste effluents. A centrifuge with a relative centrifugal force of 1318 x g, was able to reduce 60% of the turbidity. By adding the coagulant aluminum chloride, the oil-water emulsion was destabilized, and the turbidity was reduced from 3249 Formazin Attenuation Units (FAU) to around 314 FAU. With freshly generated aluminum ions in the spent cutting fluid, the electrochemical process destabilized the oil-water emulsion system. The coalesced oil droplets were adsorbed onto the highly dispersed aluminum coagulant. The oil-rich sludge that was generated in the operation was then floated to the surface, forming a blanket that was removed by skimming. The electrochemical treatment was able to reduce the turbidity to less than 14 FAU, which is the detection limit of the Hach DR/4000 UV-vis spectrophotometer.

Control Demonstration of Multiple Doubly-Fed Induction Motors for Hybrid Electric Propulsion

NASA Technical Reports Server (NTRS)

Sadey, David J.; Bodson, Marc; Csank, Jeffrey T.; Hunker, Keith R.; Theman, Casey J.; Taylor, Linda M.

2017-01-01

The Convergent Aeronautics Solutions (CAS) High Voltage-Hybrid Electric Propulsion (HVHEP) task was formulated to support the move into future hybrid-electric aircraft. The goal of this project is to develop a new AC power architecture to support the needs of higher efficiency and lower emissions. This proposed architecture will adopt the use of the doubly-fed induction machine (DFIM) for propulsor drive motor application.The Convergent Aeronautics Solutions (CAS) High Voltage-Hybrid Electric Propulsion (HVHEP) task was formulated to support the move into future hybrid-electric aircraft. The goal of this project is to develop a new AC power architecture to support the needs of higher efficiency and lower emissions. This proposed architecture will adopt the use of the doubly-fed induction machine (DFIM) for propulsor drive motor application. DFIMs are attractive for several reasons, including but not limited to the ability to self-start, ability to operate sub- and super-synchronously, and requiring only fractionally rated power converters on a per-unit basis depending on the required range of operation. The focus of this paper is based specifically on the presentation and analysis of a novel strategy which allows for independent operation of each of the aforementioned doubly-fed induction motors. This strategy includes synchronization, soft-start, and closed loop speed control of each motor as a means of controlling output thrust; be it concurrently or differentially. The demonstration of this strategy has recently been proven out on a low power test bed using fractional horsepower machines. Simulation and hardware test results are presented in the paper.

Technical Report on Occupations in Numerically Controlled Metal-Cutting Machining.

ERIC Educational Resources Information Center

Manpower Administration (DOL), Washington, DC. U.S. Employment Service.

At the present time, only 5 percent of the short-run metal-cutting machining in the United States is done by numerically controlled machined tools, but within the next decade it is expected to increase by 50 percent. Numerically controlled machines use taped data which is changed into instructions and directs the machine to do certain steps…

Units of Instruction for Vocational Office Education. Volume 1. Filing, Office Machines, and General Office Clerical Occupations. Teacher's Guide.

ERIC Educational Resources Information Center

East Texas State Univ., Commerce. Occupational Curriculum Lab.

Nineteen units on filing, office machines, and general office clerical occupations are presented in this teacher's guide. The unit topics include indexing, alphabetizing, and filing (e.g., business names); labeling and positioning file folders and guides; establishing a correspondence filing system; utilizing charge-out and follow-up file systems;…

Capability in Decline: A Historical Analysis of the Post-World War II Degradation of Domestic Railroads and the Impact on the United States Military

DTIC Science & Technology

2006-12-15

military was the logistics operations of the country, now poised to transition to more peaceful activities. The men, machines , and lines of communication...Transportation Corps to peacetime levels was underway; however, changes in missions for the Transportation Corps resulting from the lessons learned during...highways and commercial airports began their explosive growth. The risk to the military came from the learning how to incorporate the many new

Method of calculating gas dynamics and heat transfer in single stage refrigeration units

NASA Technical Reports Server (NTRS)

Zhitomirskiy, I. S.; Popolskiy, A. B.

1974-01-01

A generalized mathematical model of gas-dynamic and heat transfer processes in single-stage regenerative installations operating in Stirling, MacMahon, Gifford-MacMahon, and pulsating tube cycles is proposed. A numerical method os solving initial equations on a digital computer is given. This makes it possible to calculate the change in the thermodynamic parameters in the working cycle in different machine components, as well as the dependence of cold productivity on the temperature level in the steady regime.

Data Systems Task Analysis.

DTIC Science & Technology

1979-08-01

WHAT YOU DO IN YOUR PRESENT JOB. IdiS IS hQ A E&T. NEITHER YCU, YOUR CCMMANDER, NOR YOUR UNIT WILL BE EVALUATED , IN ANY WAY, CN THE INFORMATICN YCU...ACCOLNTING MACHINE (PCAM) OPERATOR 336. EAM/PCAM SUPERVISOR 231. EAM/PCAM WIRING TECI-NICIAN )38. EQUIPMENT MANAGEMENT TECFNICIAN 339. EVALUATION AND...R RAMO .4 12. BUNKER RAMC 13) 13. BUNKER RAMO 2)) 14. aJNKER RAMU 1563 15. BUhROdGHS 263 16. BuRROUGHS B d)) 17. BURROUGHS b35 .J 18. BjRROUGHS 847

Validation and performance of the LHC cryogenic system through commissioning of the first sector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serio, L.; Bouillot, A.; Casas-Cubillos, J.

2007-12-01

The cryogenic system [1] for the Large Hadron Collider accelerator is presently in its final phase of commissioning at nominal operating conditions. The refrigeration capacity for the LHC is produced using eight large cryogenic plants and eight 1.8 K refrigeration units installed on five cryogenic islands. Machine cryogenic equipment is installed in a 26.7-km circumference ring deep underground tunnel and are maintained at their nominal operating conditions via a distribution system consisting of transfer lines, cold interconnection boxes at each cryogenic island and a cryogenic distribution line. The functional analysis of the whole system during all operating conditions was establishedmore » and validated during the first sector commissioning in order to maximize the system availability. Analysis, operating modes, main failure scenarios, results and performance of the cryogenic system are presented.« less

Food labeling; calorie labeling of articles of food in vending machines. Final rule.

PubMed

2014-12-01

To implement the vending machine food labeling provisions of the Patient Protection and Affordable Care Act of 2010 (ACA), the Food and Drug Administration (FDA or we) is establishing requirements for providing calorie declarations for food sold from certain vending machines. This final rule will ensure that calorie information is available for certain food sold from a vending machine that does not permit a prospective purchaser to examine the Nutrition Facts Panel before purchasing the article, or does not otherwise provide visible nutrition information at the point of purchase. The declaration of accurate and clear calorie information for food sold from vending machines will make calorie information available to consumers in a direct and accessible manner to enable consumers to make informed and healthful dietary choices. This final rule applies to certain food from vending machines operated by a person engaged in the business of owning or operating 20 or more vending machines. Vending machine operators not subject to the rules may elect to be subject to the Federal requirements by registering with FDA.

The Data Egg: A new solution to text entry barriers

NASA Technical Reports Server (NTRS)

Friedman, Gary L.

1993-01-01

A unit that allows text entry with only one hand has been developed, and holds the promise of allowing computers to be truly portable. It is unique in that it allows operation in any position, freeing the user from the traditional constraints of having to be seated near a desk. This hand held, chord-key-based unit can be used either autonomously for idea capturing, or tethered to a personal computer and used as an auxiliary keyboard. Astronauts, journalists, the bedridden, and anyone else normally barred from using a computer while on the job could also benefit from this form of man-machine interface, which has been dubbed the 'Data Egg'.

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Astrophysics Data System (ADS)

Shaltens, R. K.; Birchenough, A. G.

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Operational results for the experimental DOE/NASA Mod-OA wind turbine project

NASA Technical Reports Server (NTRS)

Shaltens, R. K.; Birchenough, A. G.

1983-01-01

The Mod-OA wind turbine project which was to gain early experience in the operation of large wind turbines in a utility environment is discussed. The Mod-OA wind turbines were a first generation design, and even though not cost effective, the operating experience and performance characteristics had a significant effect on the design and development of the second and third generation machines. The Mod-OA machines were modified as a result of the operational experience, particularly the blade development and control system strategy. The results of study to investigate the interaction of a Mod-OA wind turbine with an isolated diesel generation system are discussed. The machine configuration, its advantages and disadvantages and the machine performance and availability are discussed.

Analytical expressions for maximum wind turbine average power in a Rayleigh wind regime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carlin, P.W.

Average or expectation values for annual power of a wind turbine in a Rayleigh wind regime are calculated and plotted as a function of cut-out wind speed. This wind speed is expressed in multiples of the annual average wind speed at the turbine installation site. To provide a common basis for comparison of all real and imagined turbines, the Rayleigh-Betz wind machine is postulated. This machine is an ideal wind machine operating with the ideal Betz power coefficient of 0.593 in a Rayleigh probability wind regime. All other average annual powers are expressed in fractions of that power. Cases consideredmore » include: (1) an ideal machine with finite power and finite cutout speed, (2) real machines operating in variable speed mode at their maximum power coefficient, and (3) real machines operating at constant speed.« less

Software platform virtualization in chemistry research and university teaching

PubMed Central

2009-01-01

Background Modern chemistry laboratories operate with a wide range of software applications under different operating systems, such as Windows, LINUX or Mac OS X. Instead of installing software on different computers it is possible to install those applications on a single computer using Virtual Machine software. Software platform virtualization allows a single guest operating system to execute multiple other operating systems on the same computer. We apply and discuss the use of virtual machines in chemistry research and teaching laboratories. Results Virtual machines are commonly used for cheminformatics software development and testing. Benchmarking multiple chemistry software packages we have confirmed that the computational speed penalty for using virtual machines is low and around 5% to 10%. Software virtualization in a teaching environment allows faster deployment and easy use of commercial and open source software in hands-on computer teaching labs. Conclusion Software virtualization in chemistry, mass spectrometry and cheminformatics is needed for software testing and development of software for different operating systems. In order to obtain maximum performance the virtualization software should be multi-core enabled and allow the use of multiprocessor configurations in the virtual machine environment. Server consolidation, by running multiple tasks and operating systems on a single physical machine, can lead to lower maintenance and hardware costs especially in small research labs. The use of virtual machines can prevent software virus infections and security breaches when used as a sandbox system for internet access and software testing. Complex software setups can be created with virtual machines and are easily deployed later to multiple computers for hands-on teaching classes. We discuss the popularity of bioinformatics compared to cheminformatics as well as the missing cheminformatics education at universities worldwide. PMID:20150997

Software platform virtualization in chemistry research and university teaching.

PubMed

Kind, Tobias; Leamy, Tim; Leary, Julie A; Fiehn, Oliver

2009-11-16

Modern chemistry laboratories operate with a wide range of software applications under different operating systems, such as Windows, LINUX or Mac OS X. Instead of installing software on different computers it is possible to install those applications on a single computer using Virtual Machine software. Software platform virtualization allows a single guest operating system to execute multiple other operating systems on the same computer. We apply and discuss the use of virtual machines in chemistry research and teaching laboratories. Virtual machines are commonly used for cheminformatics software development and testing. Benchmarking multiple chemistry software packages we have confirmed that the computational speed penalty for using virtual machines is low and around 5% to 10%. Software virtualization in a teaching environment allows faster deployment and easy use of commercial and open source software in hands-on computer teaching labs. Software virtualization in chemistry, mass spectrometry and cheminformatics is needed for software testing and development of software for different operating systems. In order to obtain maximum performance the virtualization software should be multi-core enabled and allow the use of multiprocessor configurations in the virtual machine environment. Server consolidation, by running multiple tasks and operating systems on a single physical machine, can lead to lower maintenance and hardware costs especially in small research labs. The use of virtual machines can prevent software virus infections and security breaches when used as a sandbox system for internet access and software testing. Complex software setups can be created with virtual machines and are easily deployed later to multiple computers for hands-on teaching classes. We discuss the popularity of bioinformatics compared to cheminformatics as well as the missing cheminformatics education at universities worldwide.

A Catalog of Performance Objectives, Performance Conditions, and Performance Guides for Machine Tool Operations.

ERIC Educational Resources Information Center

Stadt, Ronald; And Others

This catalog provides performance objectives, tasks, standards, and performance guides associated with current occupational information relating to the job content of machinists, specifically tool grinder operators, production lathe operators, and production screw machine operators. The catalog is comprised of 262 performance objectives, tool and…

Rapid Communication: Effect of machine, anatomical location, and replication on instrumental color of boneless pork loins.

PubMed

Barkley, K E; Fields, B; Dilger, A C; Boler, D D

2018-06-07

The objective was to determine the effect of machine, anatomical location and replication (multiple readings) on instrumental color and to characterize the amount of variation each factor contributed to overall color. Instrumental color was measured 3 times on the anterior and 3 times on the posterior end of 250 pork loins with 2 different Minolta CR-400 Chroma meter devices. Each Minolta was programed to use a D65 illuminant, 2º observer with an 8 mm aperture, and calibrated with white tiles specific to each machine. Therefore, a total of 12 instrumental color measurements were collected on each loin. The VARCOMP procedure in SAS was used to estimate the proportion of variation contributed by each factor to CIE L*, a*, b*, chroma and hue. Based on previous research, the average untrained consumer is able to distinguish between 3-L* units, 0.4-a* units, and 0.9-hue angle units. Loins evaluated with machine 1 were 0.71 L* units darker (P < 0.01), 1.09 b* units more yellow (P < 0.01), 0.47 chroma units more saturated (P < 0.01), and had a hue angle 5.12 units greater (P < 0.01) than when evaluated with machine 2 but did not differ (P = 0.24) in redness. The anterior portion of the loin was lighter, less red, more yellow, more saturated and had a greater hue angle than the posterior end (P < 0.01). All color trait values decreased (P < 0.01) as replication number increased. Inherent color differences among loins contributed the greatest proportion of variability for lightness (58%), redness (57%), yellowness (70%), saturation (70%) and hue angle (49%). Machine contributed 1% variability to lightness 3% to saturation, 23% to yellowness and 31% to hue angle (31%) but did not contribute to variability for redness. Anatomical location contributed 41% to lightness, 43% to redness, 7% to yellowness, 27% to saturation and 31% to hue angle. Replication did not contribute to total variation for any color traits, even though it did differ among measurements. Overall, there were differences in instrumental color values between the two machines tested but those differences were likely less than the threshold for detection by a consumer. Even so, inherent color differences between loins were a greater contributor to total variability than the differences between the 2 machines. Therefore, it is more important to define the location of measurements than replication or machine when using a Minolta CR-400 when performing color evaluations, assuming the settings are the same.

Analysis of Generator Oscillation Characteristics Based on Multiple Synchronized Phasor Measurements

NASA Astrophysics Data System (ADS)

Hashiguchi, Takuhei; Yoshimoto, Masamichi; Mitani, Yasunori; Saeki, Osamu; Tsuji, Kiichiro

In recent years, there has been considerable interest in the on-line measurement, such as observation of power system dynamics and evaluation of machine parameters. On-line methods are particularly attractive since the machine’s service need not be interrupted and parameter estimation is performed by processing measurements obtained during the normal operation of the machine. Authors placed PMU (Phasor Measurement Unit) connected to 100V outlets in some Universities in the 60Hz power system and examine oscillation characteristics in power system. PMU is synchronized based on the global positioning system (GPS) and measured data are transmitted via Internet. This paper describes an application of PMU for generator oscillation analysis. The purpose of this paper is to show methods for processing phase difference and to estimate damping coeffcient and natural angular frequency from phase difference at steady state.

Machine cost analysis using the traditional machine-rate method and ChargeOut!

Treesearch

E. M. (Ted) Bilek

2009-01-01

Forestry operations require ever more use of expensive capital equipment. Mechanization is frequently necessary to perform cost-effective and safe operations. Increased capital should mean more sophisticated capital costing methodologies. However the machine rate method, which is the costing methodology most frequently used, dates back to 1942. CHARGEOUT!, a recently...

An Analysis of the Billing and Bookkeeping Machine Operator Occupation.

ERIC Educational Resources Information Center

Six, Joseph E., Jr.

The general purpose of the occupational analysis is to provide workable, basic information dealing with the many and varied duties performed in the billing and bookkeeping machine operating occupation. The analysis was written in general terms due to the diversity in bookkeeping machines on the market, increasing number and variation of the tasks…

New developments in operator protection for forest machines

Treesearch

Robert B. Rummer; S. Taylor; M. Veal

2003-01-01

Mechanization of forest operations ha greatly improved saftey of woods work. However, increasing use of machines has introduced new hazards that must be addressed. Two of these hazards are rollover of swing-type forestry machines (currently excluded from standard protection) and the hazard of thrown objects from cutting devices. Ongoing research projects are developing...

33 CFR 157.138 - Crude Oil Washing Operations and Equipment Manual.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Revolutions, number of cycles, and length of cycles of each COW machine. (iii) Pressure and flow of the... COW machines. (ii) Revolutions, number of cycles, and length of cycles of each COW machine. (iii... § 157.140. (10) The volume of water used for water rinsing recorded during COW operations when passing...

33 CFR 157.138 - Crude Oil Washing Operations and Equipment Manual.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Revolutions, number of cycles, and length of cycles of each COW machine. (iii) Pressure and flow of the... COW machines. (ii) Revolutions, number of cycles, and length of cycles of each COW machine. (iii... § 157.140. (10) The volume of water used for water rinsing recorded during COW operations when passing...

33 CFR 157.138 - Crude Oil Washing Operations and Equipment Manual.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Revolutions, number of cycles, and length of cycles of each COW machine. (iii) Pressure and flow of the... COW machines. (ii) Revolutions, number of cycles, and length of cycles of each COW machine. (iii... § 157.140. (10) The volume of water used for water rinsing recorded during COW operations when passing...

40 CFR 63.322 - Standards.

Code of Federal Regulations, 2013 CFR

2013-07-01

... at each opening at all times that the machine is operating. (b) The owner or operator of each new dry... articles to or from the machine, and shall keep the door closed at all other times. (d) The owner or... existing dry cleaning system and of each new transfer machine system and its ancillary equipment installed...

40 CFR 63.322 - Standards.

Code of Federal Regulations, 2012 CFR

2012-07-01

... at each opening at all times that the machine is operating. (b) The owner or operator of each new dry... articles to or from the machine, and shall keep the door closed at all other times. (d) The owner or... existing dry cleaning system and of each new transfer machine system and its ancillary equipment installed...

Machine learning algorithms based on signals from a single wearable inertial sensor can detect surface- and age-related differences in walking.

PubMed

Hu, B; Dixon, P C; Jacobs, J V; Dennerlein, J T; Schiffman, J M

2018-04-11

The aim of this study was to investigate if a machine learning algorithm utilizing triaxial accelerometer, gyroscope, and magnetometer data from an inertial motion unit (IMU) could detect surface- and age-related differences in walking. Seventeen older (71.5 ± 4.2 years) and eighteen young (27.0 ± 4.7 years) healthy adults walked over flat and uneven brick surfaces wearing an inertial measurement unit (IMU) over the L5 vertebra. IMU data were binned into smaller data segments using 4-s sliding windows with 1-s step lengths. Ninety percent of the data were used as training inputs and the remaining ten percent were saved for testing. A deep learning network with long short-term memory units was used for training (fully supervised), prediction, and implementation. Four models were trained using the following inputs: all nine channels from every sensor in the IMU (fully trained model), accelerometer signals alone, gyroscope signals alone, and magnetometer signals alone. The fully trained models for surface and age outperformed all other models (area under the receiver operator curve, AUC = 0.97 and 0.96, respectively; p ≤ .045). The fully trained models for surface and age had high accuracy (96.3, 94.7%), precision (96.4, 95.2%), recall (96.3, 94.7%), and f1-score (96.3, 94.6%). These results demonstrate that processing the signals of a single IMU device with machine-learning algorithms enables the detection of surface conditions and age-group status from an individual's walking behavior which, with further learning, may be utilized to facilitate identifying and intervening on fall risk. Copyright © 2018 Elsevier Ltd. All rights reserved.

Data analysis on physical and mechanical properties of cassava pellets.

PubMed

Oguntunde, Pelumi E; Adejumo, Oluyemisi A; Odetunmibi, Oluwole A; Okagbue, Hilary I; Adejumo, Adebowale O

2018-02-01

In this data article, laboratory experimental investigation results carried out at National Centre for Agricultural Mechanization (NCAM) on moisture content, machine speed, die diameter of the rig, and the outputs (hardness, durability, bulk density, and unit density of the pellets) at different levels of cassava pellets were observed. Analysis of variance using randomized complete block design with factorial was used to perform analysis for each of the outputs: hardness, durability, bulk density, and unit density of the pellets. A clear description on each of these outputs was considered separately using tables and figures. It was observed that for all the output with the exception of unit density, their main factor effects as well as two and three ways interactions is significant at 5% level. This means that the hardness, bulk density and durability of cassava pellets respectively depend on the moisture content of the cassava dough, the machine speed, the die diameter of the extrusion rig and the combinations of these factors in pairs as well as the three altogether. Higher machine speeds produced more quality pellets at lower die diameters while lower machine speed is recommended for higher die diameter. Also the unit density depends on die diameter and the three-way interaction only. Unit density of cassava pellets is neither affected by machine parameters nor moisture content of the cassava dough. Moisture content of cassava dough, speed of the machine and die diameter of the extrusion rig are significant factors to be considered in pelletizing cassava to produce pellets. Increase in moisture content of cassava dough increase the quality of cassava pellets.

Development of Energy Models for Production Systems and Processes to Inform Environmentally Benign Decision-Making

NASA Astrophysics Data System (ADS)

Diaz-Elsayed, Nancy

Between 2008 and 2035 global energy demand is expected to grow by 53%. While most industry-level analyses of manufacturing in the United States (U.S.) have traditionally focused on high energy consumers such as the petroleum, chemical, paper, primary metal, and food sectors, the remaining sectors account for the majority of establishments in the U.S. Specifically, of the establishments participating in the Energy Information Administration's Manufacturing Energy Consumption Survey in 2006, the non-energy intensive" sectors still consumed 4*109 GJ of energy, i.e., one-quarter of the energy consumed by the manufacturing sectors, which is enough to power 98 million homes for a year. The increasing use of renewable energy sources and the introduction of energy-efficient technologies in manufacturing operations support the advancement towards a cleaner future, but having a good understanding of how the systems and processes function can reduce the environmental burden even further. To facilitate this, methods are developed to model the energy of manufacturing across three hierarchical levels: production equipment, factory operations, and industry; these methods are used to accurately assess the current state and provide effective recommendations to further reduce energy consumption. First, the energy consumption of production equipment is characterized to provide machine operators and product designers with viable methods to estimate the environmental impact of the manufacturing phase of a product. The energy model of production equipment is tested and found to have an average accuracy of 97% for a product requiring machining with a variable material removal rate profile. However, changing the use of production equipment alone will not result in an optimal solution since machines are part of a larger system. Which machines to use, how to schedule production runs while accounting for idle time, the design of the factory layout to facilitate production, and even the machining parameters --- these decisions affect how much energy is utilized during production. Therefore, at the facility level a methodology is presented for implementing priority queuing while accounting for a high product mix in a discrete event simulation environment. A baseline case is presented and alternative factory designs are suggested, which lead to energy savings of approximately 9%. At the industry level, the majority of energy consumption for manufacturing facilities is utilized for machine drive, process heating, and HVAC. Numerous studies have characterized the energy of manufacturing processes and HVAC equipment, but energy data is often limited for a facility in its entirety since manufacturing companies often lack the appropriate sensors to track it and are hesitant to release this information for confidentiality purposes. Without detailed information about the use of energy in manufacturing sites, the scope of factory studies cannot be adequately defined. Therefore, the breakdown of energy consumption of sectors with discrete production is presented, as well as a case study assessing the electrical energy consumption, greenhouse gas emissions, their associated costs, and labor costs for selected sites in the United States, Japan, Germany, China, and India. By presenting energy models and assessments of production equipment, factory operations, and industry, this dissertation provides a comprehensive assessment of energy trends in manufacturing and recommends methods that can be used beyond these case studies and industries to reduce consumption and contribute to an energy-efficient future.

Image quality assessment and medical physics evaluation of different portable dental X-ray units.

PubMed

Pittayapat, Pisha; Oliveira-Santos, Christiano; Thevissen, Patrick; Michielsen, Koen; Bergans, Niki; Willems, Guy; Debruyckere, Deborah; Jacobs, Reinhilde

2010-09-10

Recently developed portable dental X-ray units increase the mobility of the forensic odontologists and allow more efficient X-ray work in a disaster field, especially when used in combination with digital sensors. This type of machines might also have potential for application in remote areas, military and humanitarian missions, dental care of patients with mobility limitation, as well as imaging in operating rooms. To evaluate radiographic image quality acquired by three portable X-ray devices in combination with four image receptors and to evaluate their medical physics parameters. Images of five samples consisting of four teeth and one formalin-fixed mandible were acquired by one conventional wall-mounted X-ray unit, MinRay 60/70 kVp, used as a clinical standard, and three portable dental X-ray devices: AnyRay 60 kVp, Nomad 60 kVp and Rextar 70 kVp, in combination with a phosphor image plate (PSP), a CCD, or a CMOS sensor. Three observers evaluated images for standard image quality besides forensic diagnostic quality on a 4-point rating scale. Furthermore, all machines underwent tests for occupational as well as patient dosimetry. Statistical analysis showed good quality imaging for all system, with the combination of Nomad and PSP yielding the best score. A significant difference in image quality between the combination of the four X-ray devices and four sensors was established (p<0.05). For patient safety, the exposure rate was determined and exit dose rates for MinRay at 60 kVp, MinRay at 70 kVp, AnyRay, Nomad and Rextar were 3.4 mGy/s, 4.5 mGy/s, 13.5 mGy/s, 3.8 mGy/s and 2.6 mGy/s respectively. The kVp of the AnyRay system was the most stable, with a ripple of 3.7%. Short-term variations in the tube output of all the devices were less than 10%. AnyRay presented higher estimated effective dose than other machines. Occupational dosimetry showed doses at the operator's hand being lowest with protective shielding (Nomad: 0.1 microGy). It was also low while using remote control (distance>1m: Rextar <0.2 microGy, MinRay <0.1 microGy). The present study demonstrated the feasibility of three portable X-ray systems to be used for specific indications, based on acceptable image quality and sufficient accuracy of the machines and following the standard guidelines for radiation hygiene. Copyright 2010 Elsevier Ireland Ltd. All rights reserved.

Machine vision for real time orbital operations

NASA Technical Reports Server (NTRS)

Vinz, Frank L.

1988-01-01

Machine vision for automation and robotic operation of Space Station era systems has the potential for increasing the efficiency of orbital servicing, repair, assembly and docking tasks. A machine vision research project is described in which a TV camera is used for inputing visual data to a computer so that image processing may be achieved for real time control of these orbital operations. A technique has resulted from this research which reduces computer memory requirements and greatly increases typical computational speed such that it has the potential for development into a real time orbital machine vision system. This technique is called AI BOSS (Analysis of Images by Box Scan and Syntax).

Development of a plan for automating integrated circuit processing

NASA Technical Reports Server (NTRS)

1971-01-01

The operations analysis and equipment evaluations pertinent to the design of an automated production facility capable of manufacturing beam-lead CMOS integrated circuits are reported. The overall plan shows approximate cost of major equipment, production rate and performance capability, flexibility, and special maintenance requirements. Direct computer control is compared with supervisory-mode operations. The plan is limited to wafer processing operations from the starting wafer to the finished beam-lead die after separation etching. The work already accomplished in implementing various automation schemes, and the type of equipment which can be found for instant automation are described. The plan is general, so that small shops or large production units can perhaps benefit. Examples of major types of automated processing machines are shown to illustrate the general concepts of automated wafer processing.

Method and system for controlling a synchronous machine over full operating range

DOEpatents

Walters, James E.; Gunawan, Fani S.; Xue, Yanhong

2002-01-01

System and method for controlling a synchronous machine are provided. The method allows for calculating a stator voltage index. The method further allows for relating the magnitude of the stator voltage index against a threshold voltage value. An offset signal is generated based on the results of the relating step. A respective state of operation of the machine is determined. The offset signal is processed based on the respective state of the machine.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lumsdaine, A.; Bjorholm, T.; Harris, J.

The Wendelstein 7-X stellarator is in final stages of commissioning, and will begin operation in late 2015. In the first phase, the machine will operate with a limiter, and will be restricted to low power and short pulse. But in 2019, plans are for an actively cooled divertor to be installed, and the machine will operate in steady state at full power. Recently, plasma simulations have indicated that, in this final operational phase, a bootstrap current will evolve in certain scenarios. This will cause the sensitive ends of the divertor target to be overloaded beyond their qualified limit. A highmore » heat flux scraper element (HHF-SE) has been proposed in order to take up some of the convective flux and reduce the load on the divertor. In order to examine whether the HHF-SE will be able to effectively reduce the plasma flux in the divertor region of concern, and to determine how the pumping effectiveness will be affected by such a component, it is planned to include a test divertor unit scraper element (TDU-SE) in 2017 during an earlier operational phase. Several U.S. fusion energy science laboratories have been involved in the design, analysis (structural and thermal finite element, as well as computational fluid dynamics), plasma simulation, planning, prototyping, and diagnostic development around the scraper element program (both TDU-SE and HHF-SE). As a result, this paper presents an overview of all of these activities and their current status.« less

Overview of design and analysis activities for the W7-X scraper element

DOE PAGES

Lumsdaine, A.; Bjorholm, T.; Harris, J.; ...

2016-08-18

The Wendelstein 7-X stellarator is in final stages of commissioning, and will begin operation in late 2015. In the first phase, the machine will operate with a limiter, and will be restricted to low power and short pulse. But in 2019, plans are for an actively cooled divertor to be installed, and the machine will operate in steady state at full power. Recently, plasma simulations have indicated that, in this final operational phase, a bootstrap current will evolve in certain scenarios. This will cause the sensitive ends of the divertor target to be overloaded beyond their qualified limit. A highmore » heat flux scraper element (HHF-SE) has been proposed in order to take up some of the convective flux and reduce the load on the divertor. In order to examine whether the HHF-SE will be able to effectively reduce the plasma flux in the divertor region of concern, and to determine how the pumping effectiveness will be affected by such a component, it is planned to include a test divertor unit scraper element (TDU-SE) in 2017 during an earlier operational phase. Several U.S. fusion energy science laboratories have been involved in the design, analysis (structural and thermal finite element, as well as computational fluid dynamics), plasma simulation, planning, prototyping, and diagnostic development around the scraper element program (both TDU-SE and HHF-SE). As a result, this paper presents an overview of all of these activities and their current status.« less

Predictive Surface Roughness Model for End Milling of Machinable Glass Ceramic

NASA Astrophysics Data System (ADS)

Mohan Reddy, M.; Gorin, Alexander; Abou-El-Hossein, K. A.

2011-02-01

Advanced ceramics of Machinable glass ceramic is attractive material to produce high accuracy miniaturized components for many applications in various industries such as aerospace, electronics, biomedical, automotive and environmental communications due to their wear resistance, high hardness, high compressive strength, good corrosion resistance and excellent high temperature properties. Many research works have been conducted in the last few years to investigate the performance of different machining operations when processing various advanced ceramics. Micro end-milling is one of the machining methods to meet the demand of micro parts. Selecting proper machining parameters are important to obtain good surface finish during machining of Machinable glass ceramic. Therefore, this paper describes the development of predictive model for the surface roughness of Machinable glass ceramic in terms of speed, feed rate by using micro end-milling operation.

Creation of operation algorithms for combined operation of anti-lock braking system (ABS) and electric machine included in the combined power plant

NASA Astrophysics Data System (ADS)

Bakhmutov, S. V.; Ivanov, V. G.; Karpukhin, K. E.; Umnitsyn, A. A.

2018-02-01

The paper considers the Anti-lock Braking System (ABS) operation algorithm, which enables the implementation of hybrid braking, i.e. the braking process combining friction brake mechanisms and e-machine (electric machine), which operates in the energy recovery mode. The provided materials focus only on the rectilinear motion of the vehicle. That the ABS task consists in the maintenance of the target wheel slip ratio, which depends on the tyre-road adhesion coefficient. The tyre-road adhesion coefficient was defined based on the vehicle deceleration. In the course of calculated studies, the following operation algorithm of hybrid braking was determined. At adhesion coefficient ≤0.1, driving axle braking occurs only due to the e-machine operating in the energy recovery mode. In other cases, depending on adhesion coefficient, the e-machine provides the brake torque, which changes from 35 to 100% of the maximum available brake torque. Virtual tests showed that values of the wheel slip ratio are close to the required ones. Thus, this algorithm makes it possible to implement hybrid braking by means of the two sources creating the brake torque.

Calculating with light using a chip-scale all-optical abacus.

PubMed

Feldmann, J; Stegmaier, M; Gruhler, N; Ríos, C; Bhaskaran, H; Wright, C D; Pernice, W H P

2017-11-02

Machines that simultaneously process and store multistate data at one and the same location can provide a new class of fast, powerful and efficient general-purpose computers. We demonstrate the central element of an all-optical calculator, a photonic abacus, which provides multistate compute-and-store operation by integrating functional phase-change materials with nanophotonic chips. With picosecond optical pulses we perform the fundamental arithmetic operations of addition, subtraction, multiplication, and division, including a carryover into multiple cells. This basic processing unit is embedded into a scalable phase-change photonic network and addressed optically through a two-pulse random access scheme. Our framework provides first steps towards light-based non-von Neumann arithmetic.

Automatic soldering machine

NASA Technical Reports Server (NTRS)

Stein, J. A.

1974-01-01

Fully-automatic tube-joint soldering machine can be used to make leakproof joints in aluminum tubes of 3/16 to 2 in. in diameter. Machine consists of temperature-control unit, heater transformer and heater head, vibrator, and associated circuitry controls, and indicators.

Automated visual imaging interface for the plant floor

NASA Astrophysics Data System (ADS)

Wutke, John R.

1991-03-01

The paper will provide an overview of the challenges facing a user of automated visual imaging (" AVI" ) machines and the philosophies that should be employed in designing them. As manufacturing tools and equipment become more sophisticated it is increasingly difficult to maintain an efficient interaction between the operator and machine. The typical user of an AVI machine in a production environment is technically unsophisticated. Also operator and machine ergonomics are often a neglected or poorly addressed part of an efficient manufacturing process. This paper presents a number of man-machine interface design techniques and philosophies that effectively solve these problems.

Deep Restricted Kernel Machines Using Conjugate Feature Duality.

PubMed

Suykens, Johan A K

2017-08-01

The aim of this letter is to propose a theory of deep restricted kernel machines offering new foundations for deep learning with kernel machines. From the viewpoint of deep learning, it is partially related to restricted Boltzmann machines, which are characterized by visible and hidden units in a bipartite graph without hidden-to-hidden connections and deep learning extensions as deep belief networks and deep Boltzmann machines. From the viewpoint of kernel machines, it includes least squares support vector machines for classification and regression, kernel principal component analysis (PCA), matrix singular value decomposition, and Parzen-type models. A key element is to first characterize these kernel machines in terms of so-called conjugate feature duality, yielding a representation with visible and hidden units. It is shown how this is related to the energy form in restricted Boltzmann machines, with continuous variables in a nonprobabilistic setting. In this new framework of so-called restricted kernel machine (RKM) representations, the dual variables correspond to hidden features. Deep RKM are obtained by coupling the RKMs. The method is illustrated for deep RKM, consisting of three levels with a least squares support vector machine regression level and two kernel PCA levels. In its primal form also deep feedforward neural networks can be trained within this framework.

Development and Demonstration of Adanced Tooling Alloys for Molds and Dies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kevin M. McHugh; Enrique J. Lavernia

2006-01-01

This report summarizes research results in the project Development and Demonstration of Advanced Tooling Alloys for Molds and Dies. Molds, dies and related tooling are used to manufacture most of the plastic and metal products we use every day. Conventional fabrication of molds and dies involves a multiplicity of machining, benching and heat treatment unit operations. This approach is very expensive and time consuming. Rapid Solidifcation Process (RSP) Tooling is a spray-forming technology tailored for producing molds and dies. The appraoch combines rapid solidifcation processing and net-shape materials processing in a single step. An atomized spray of a tool-forming alloy,more » typically a tool steel, is deposited onto an easy-to-form tool pattern to replicate the pattern's shape and surface features. By so doing, the approach eliminates many machining operations in conventional mold making, significantly reducing cost, lead time and energy. Moreover, rapid solidification creates unique microstructural features by suppressing carbide precipitation and growth, and creating metastable phases. This can result in unique material properties following heat treatment. Spray-formed and aged tool steel dies have exhibited extended life compared to conventional dies in many forming operations such as forging, extrusion and die casting. RSP Tooling technolocy was commercialized with the formation of RSP Tooling, LLC in Solon, Oh.« less

The reduction methods of operator's radiation dose for portable dental X-ray machines.

PubMed

Cho, Jeong-Yeon; Han, Won-Jeong

2012-08-01

This study was aimed to investigate the methods to reduce operator's radiation dose when taking intraoral radiographs with portable dental X-ray machines. Two kinds of portable dental X-ray machines (DX3000, Dexcowin and Rextar, Posdion) were used. Operator's radiation dose was measured with an 1,800 cc ionization chamber (RadCal Corp.) at the hand level of X-ray tubehead and at the operator's chest and waist levels with and without the backscatter shield. The operator's radiation dose at the hand level was measured with and without lead gloves and with long and short cones. The backscatter shield reduced operator's radiation dose at the hand level of X-ray tubehead to 23 - 32%, the lead gloves to 26 - 31%, and long cone to 48 - 52%. And the backscatter shield reduced operator's radiation dose at the operator's chest and waist levels to 0.1 - 37%. When portable dental X-ray systems are used, it is recommended to select X-ray machine attached with a backscatter shield and a long cone and to wear the lead gloves.

Efficient forced vibration reanalysis method for rotating electric machines

NASA Astrophysics Data System (ADS)

Saito, Akira; Suzuki, Hiromitsu; Kuroishi, Masakatsu; Nakai, Hideo

2015-01-01

Rotating electric machines are subject to forced vibration by magnetic force excitation with wide-band frequency spectrum that are dependent on the operating conditions. Therefore, when designing the electric machines, it is inevitable to compute the vibration response of the machines at various operating conditions efficiently and accurately. This paper presents an efficient frequency-domain vibration analysis method for the electric machines. The method enables the efficient re-analysis of the vibration response of electric machines at various operating conditions without the necessity to re-compute the harmonic response by finite element analyses. Theoretical background of the proposed method is provided, which is based on the modal reduction of the magnetic force excitation by a set of amplitude-modulated standing-waves. The method is applied to the forced response vibration of the interior permanent magnet motor at a fixed operating condition. The results computed by the proposed method agree very well with those computed by the conventional harmonic response analysis by the FEA. The proposed method is then applied to the spin-up test condition to demonstrate its applicability to various operating conditions. It is observed that the proposed method can successfully be applied to the spin-up test conditions, and the measured dominant frequency peaks in the frequency response can be well captured by the proposed approach.

National machine guarding program: Part 1. Machine safeguarding practices in small metal fabrication businesses

PubMed Central

Yamin, Samuel C.; Brosseau, Lisa M.; Xi, Min; Gordon, Robert; Most, Ivan G.; Stanley, Rodney

2015-01-01

Background Metal fabrication workers experience high rates of traumatic occupational injuries. Machine operators in particular face high risks, often stemming from the absence or improper use of machine safeguarding or the failure to implement lockout procedures. Methods The National Machine Guarding Program (NMGP) was a translational research initiative implemented in conjunction with two workers' compensation insures. Insurance safety consultants trained in machine guarding used standardized checklists to conduct a baseline inspection of machine‐related hazards in 221 business. Results Safeguards at the point of operation were missing or inadequate on 33% of machines. Safeguards for other mechanical hazards were missing on 28% of machines. Older machines were both widely used and less likely than newer machines to be properly guarded. Lockout/tagout procedures were posted at only 9% of machine workstations. Conclusions The NMGP demonstrates a need for improvement in many aspects of machine safety and lockout in small metal fabrication businesses. Am. J. Ind. Med. 58:1174–1183, 2015. © 2015 The Authors. American Journal of Industrial Medicine published by Wiley Periodicals, Inc. PMID:26332060

Energy: Machines, Science (Experimental): 5311.03.

ERIC Educational Resources Information Center

Castaldi, June P.

This unit of instruction was designed as an introductory course in energy involving six simple machines, electricity, magnetism, and motion. The booklet lists the relevant state-adopted texts and states the performance objectives for the unit. It provides an outline of the course content and suggests experiments, demonstrations, field trips, and…

Effect of Carbon in the Dielectric Fluid and Workpieces on the Characteristics of Recast Layers Machined by Electrical Discharge Machining

NASA Astrophysics Data System (ADS)

Muttamara, Apiwat; Kanchanomai, Chaosuan

2016-06-01

Electrical discharge machining (EDM) is a popular non-traditional machining technique that is usually performed in kerosene. Carbon from the kerosene is mixed into the recast layer during EDM, increasing its hardness. EDM can be performed in deionized water, which causes decarburization. We studied the effects of carbon in the dielectric fluid and workpiece on the characteristics of recast layers. Experiments were conducted using gray cast iron and mild steel workpieces in deionized water or kerosene under identical operating conditions. Scanning electron microscopy revealed that the recast layer formed on gray iron was rougher than that produced on mild steel. Moreover, the dispersion of graphite flakes in the gray iron seemed to cause subsurface cracks, even when EDM was performed in deionized water. Dendritic structures and iron carbides were found in the recast layer of gray iron treated in deionized water. Kerosene caused more microcracks to form and increased surface roughness compared with deionized water. The microcrack length per unit area of mild steel treated in deionized water was greater than that treated in kerosene, but the cracks formed in kerosene were wider. The effect of the diffusion of carbon during cooling on the characteristics of the recast layer was discussed.

Comprehensive experimental and numerical analysis of instability phenomena in pump turbines

NASA Astrophysics Data System (ADS)

Gentner, Ch; Sallaberger, M.; Widmer, Ch; Bobach, B.-J.; Jaberg, H.; Schiffer, J.; Senn, F.; Guggenberger, M.

2014-03-01

The changes in the electricity market have led to changed requirements for the operation of pump turbines. Utilities need to change fast and frequently between pumping and generating modes and increasingly want to operate at off-design conditions for extended periods. Operation of the units in instable areas of the machine characteristic is not acceptable and may lead to self-excited vibration of the hydraulic system. In turbine operation of pump turbines unstable behaviour can occur at low load off-design operation close to runaway conditions (S-shape of the turbine characteristic). This type of instability may impede the synchronization of the machine in turbine mode and thus increase start-up and switch over times. A pronounced S-shaped instability can also lead to significant drop of discharge in the event of load rejection. Low pressure on the suction side and in the tail-race tunnel could cause dangerous separation of the water column. Understanding the flow features that lead to the instable behaviour of pump turbines is a prerequisite to the design of machines that can fulfil the growing requirements relating to operational flexibility. Flow simulation in these instability zones is demanding due to the complex and highly unsteady flow patterns. Only unsteady simulation methods are able to reproduce the governing physical effects in these operating regions. ANDRITZ HYDRO has been investigating the stability behaviour of pump turbines in turbine operation in cooperation with several universities using simulation and measurements. In order to validate the results of flow simulation of unstable operating points, the Graz University of Technology (Austria) performed detailed experimental investigations. Within the scope of a long term research project, the operating characteristics of several pump turbine runners have been measured and flow patterns in the pump turbine at speed no load and runaway have been examined by 2D Laser particle image velocimetry (PIV). For several wicket gate positions, the flow fields in the vane-less space at runner inlet observed in the experiment are compared with the results of unsteady CFD flow simulations. Physical phenomena are visualized and insight to flow phenomena is given. Analyses using both results of simulation and measurement allow deriving a consistent explanation of the fluid mechanical mechanisms leading to the S-shaped instability of pump turbines.

32 CFR 701.53 - FOIA fee schedule.

Code of Federal Regulations, 2014 CFR

2014-07-01

... human time) and machine time. (1) Human time. Human time is all the time spent by humans performing the...) Machine time. Machine time involves only direct costs of the central processing unit (CPU), input/output... exist to calculate CPU time, no machine costs can be passed on to the requester. When CPU calculations...

32 CFR 701.53 - FOIA fee schedule.

Code of Federal Regulations, 2012 CFR

2012-07-01

... human time) and machine time. (1) Human time. Human time is all the time spent by humans performing the...) Machine time. Machine time involves only direct costs of the central processing unit (CPU), input/output... exist to calculate CPU time, no machine costs can be passed on to the requester. When CPU calculations...

32 CFR 701.53 - FOIA fee schedule.

Code of Federal Regulations, 2013 CFR

2013-07-01

... human time) and machine time. (1) Human time. Human time is all the time spent by humans performing the...) Machine time. Machine time involves only direct costs of the central processing unit (CPU), input/output... exist to calculate CPU time, no machine costs can be passed on to the requester. When CPU calculations...

Design, evaluation and recommedation effort relating to the modification of a residential 3-ton absorption cycle cooling unit for operation with solar energy

NASA Technical Reports Server (NTRS)

Merrick, R. H.; Anderson, P. P.

1973-01-01

The possible use of solar energy powered absorption units to provide cooling and heating of residential buildings is studied. Both, the ammonia-water and the water-lithium bromide cycles, are considered. It is shown that the air cooled ammonia water unit does not meet the criteria for COP and pump power on the cooling cycle and the heat obtained from it acting as a heat pump is at too low a temperature. If the ammonia machine is water cooled it will meet the design criteria for cooling but can not supply the heating needs. The water cooled lithium bromide unit meets the specified performance for cooling with appreciably lower generator temperatures and without a mechanical solution pump. It is recommeded that in the demonstration project a direct expansion lithium bromide unit be used for cooling and an auxiliary duct coil using the solar heated water be employed for heating.

Future of Mechatronics and Human

NASA Astrophysics Data System (ADS)

Harashima, Fumio; Suzuki, Satoshi

This paper mentions circumstance of mechatronics that sustain our human society, and introduces HAM(Human Adaptive Mechatronics)-project as one of research projects to create new human-machine system. The key point of HAM is skill, and analysis of skill and establishment of assist method to enhance total performance of human-machine system are main research concerns. As study of skill is an elucidation of human itself, analyses of human higher function are significant. In this paper, after surveying researches of human brain functions, an experimental analysis of human characteristic in machine operation is shown as one example of our research activities. We used hovercraft simulator as verification system including observation, voluntary motion control and machine operation that are needed to general machine operation. Process and factors to become skilled were investigated by identification of human control characteristics with measurement of the operator's line-of sight. It was confirmed that early switching of sub-controllers / reference signals in human and enhancement of space perception are significant.

Modelling of human-machine interaction in equipment design of manufacturing cells

NASA Astrophysics Data System (ADS)

Cochran, David S.; Arinez, Jorge F.; Collins, Micah T.; Bi, Zhuming

2017-08-01

This paper proposes a systematic approach to model human-machine interactions (HMIs) in supervisory control of machining operations; it characterises the coexistence of machines and humans for an enterprise to balance the goals of automation/productivity and flexibility/agility. In the proposed HMI model, an operator is associated with a set of behavioural roles as a supervisor for multiple, semi-automated manufacturing processes. The model is innovative in the sense that (1) it represents an HMI based on its functions for process control but provides the flexibility for ongoing improvements in the execution of manufacturing processes; (2) it provides a computational tool to define functional requirements for an operator in HMIs. The proposed model can be used to design production systems at different levels of an enterprise architecture, particularly at the machine level in a production system where operators interact with semi-automation to accomplish the goal of 'autonomation' - automation that augments the capabilities of human beings.

Operating System For Numerically Controlled Milling Machine

NASA Technical Reports Server (NTRS)

Ray, R. B.

1992-01-01

OPMILL program is operating system for Kearney and Trecker milling machine providing fast easy way to program manufacture of machine parts with IBM-compatible personal computer. Gives machinist "equation plotter" feature, which plots equations that define movements and converts equations to milling-machine-controlling program moving cutter along defined path. System includes tool-manager software handling up to 25 tools and automatically adjusts to account for each tool. Developed on IBM PS/2 computer running DOS 3.3 with 1 MB of random-access memory.

A review on prognostic techniques for non-stationary and non-linear rotating systems

NASA Astrophysics Data System (ADS)

Kan, Man Shan; Tan, Andy C. C.; Mathew, Joseph

2015-10-01

The field of prognostics has attracted significant interest from the research community in recent times. Prognostics enables the prediction of failures in machines resulting in benefits to plant operators such as shorter downtimes, higher operation reliability, reduced operations and maintenance cost, and more effective maintenance and logistics planning. Prognostic systems have been successfully deployed for the monitoring of relatively simple rotating machines. However, machines and associated systems today are increasingly complex. As such, there is an urgent need to develop prognostic techniques for such complex systems operating in the real world. This review paper focuses on prognostic techniques that can be applied to rotating machinery operating under non-linear and non-stationary conditions. The general concept of these techniques, the pros and cons of applying these methods, as well as their applications in the research field are discussed. Finally, the opportunities and challenges in implementing prognostic systems and developing effective techniques for monitoring machines operating under non-stationary and non-linear conditions are also discussed.

Human factors model concerning the man-machine interface of mining crewstations

NASA Technical Reports Server (NTRS)

Rider, James P.; Unger, Richard L.

1989-01-01

The U.S. Bureau of Mines is developing a computer model to analyze the human factors aspect of mining machine operator compartments. The model will be used as a research tool and as a design aid. It will have the capability to perform the following: simulated anthropometric or reach assessment, visibility analysis, illumination analysis, structural analysis of the protective canopy, operator fatigue analysis, and computation of an ingress-egress rating. The model will make extensive use of graphics to simplify data input and output. Two dimensional orthographic projections of the machine and its operator compartment are digitized and the data rebuilt into a three dimensional representation of the mining machine. Anthropometric data from either an individual or any size population may be used. The model is intended for use by equipment manufacturers and mining companies during initial design work on new machines. In addition to its use in machine design, the model should prove helpful as an accident investigation tool and for determining the effects of machine modifications made in the field on the critical areas of visibility and control reach ability.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Angers, Crystal Plume; Bottema, Ryan; Buckley, Les

Purpose: Treatment unit uptime statistics are typically used to monitor radiation equipment performance. The Ottawa Hospital Cancer Centre has introduced the use of Quality Control (QC) test success as a quality indicator for equipment performance and overall health of the equipment QC program. Methods: Implemented in 2012, QATrack+ is used to record and monitor over 1100 routine machine QC tests each month for 20 treatment and imaging units ( http://qatrackplus.com/ ). Using an SQL (structured query language) script, automated queries of the QATrack+ database are used to generate program metrics such as the number of QC tests executed and themore » percentage of tests passing, at tolerance or at action. These metrics are compared against machine uptime statistics already reported within the program. Results: Program metrics for 2015 show good correlation between pass rate of QC tests and uptime for a given machine. For the nine conventional linacs, the QC test success rate was consistently greater than 97%. The corresponding uptimes for these units are better than 98%. Machines that consistently show higher failure or tolerance rates in the QC tests have lower uptimes. This points to either poor machine performance requiring corrective action or to problems with the QC program. Conclusions: QATrack+ significantly improves the organization of QC data but can also aid in overall equipment management. Complimenting machine uptime statistics with QC test metrics provides a more complete picture of overall machine performance and can be used to identify areas of improvement in the machine service and QC programs.« less

Computer Associates International, CA-ACF2/VM Release 3.1

DTIC Science & Technology

1987-09-09

Associates CA-ACF2/VM Bibliography International Business Machines Corporation, IBM Virtual Machine/Directory Maintenance Program Logic Manual...publication number LY20-0889 International Business Machines International Business Machines Corporation, IBM System/370 Principles of Operation...publication number GA22-7000 International Business Machines Corporation, IBM Virtual Machine/Directory Maintenance Installation and System Administrator’s

34 CFR 395.1 - Terms.

Code of Federal Regulations, 2014 CFR

2014-07-01

... machine or a vending facility on the same premises as a vending facility operated by a blind vendor, except that vending machines or vending facilities operated in areas serving employees the majority of... time required to patronize the vending facility) to the vending facility operated by a blind vendor...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

34 CFR 395.1 - Terms.

Code of Federal Regulations, 2013 CFR

2013-07-01

... machine or a vending facility on the same premises as a vending facility operated by a blind vendor, except that vending machines or vending facilities operated in areas serving employees the majority of... time required to patronize the vending facility) to the vending facility operated by a blind vendor...

32 CFR 260.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... operations. Direct competition. The presence and operation of a DoD Component vending machine or a vending... machines or vending facilities operated in areas serving employees, the majority of whom normally do not have access (in terms of uninterrupted ease of approach and the amount of time required to patronize...

32 CFR 260.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... operations. Direct competition. The presence and operation of a DoD Component vending machine or a vending... machines or vending facilities operated in areas serving employees, the majority of whom normally do not have access (in terms of uninterrupted ease of approach and the amount of time required to patronize...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

32 CFR 260.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operations. Direct competition. The presence and operation of a DoD Component vending machine or a vending... machines or vending facilities operated in areas serving employees, the majority of whom normally do not have access (in terms of uninterrupted ease of approach and the amount of time required to patronize...

40 CFR 63.1542 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... materials are introduced into a sinter machine, blast furnace, or dross furnace. Dross furnace means any... which material is prepared for charging to a sinter machine or smelting furnace or other lead processing operation. Operating time means the period of time in hours that an affected source is in operation...

34 CFR 395.1 - Terms.

Code of Federal Regulations, 2012 CFR

2012-07-01

... machine or a vending facility on the same premises as a vending facility operated by a blind vendor, except that vending machines or vending facilities operated in areas serving employees the majority of... time required to patronize the vending facility) to the vending facility operated by a blind vendor...

Method of fabricating a micro machine

DOEpatents

Stalford, Harold L

2014-11-11

A micro machine may be in or less than the micrometer domain. The micro machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft is operable to be driven by the micro actuator. A tool is coupled to the micro shaft and is operable to perform work in response to at least motion of the micro shaft.

Methods and systems for micro machines

DOEpatents

Stalford, Harold L.

2018-03-06

A micro machine may be in or less than the micrometer domain. The micro machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft is operable to be driven by the micro actuator. A tool is coupled to the micro shaft and is operable to perform work in response to at least motion of the micro shaft.

Methods and systems for micro machines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stalford, Harold L.

2017-04-11

A micro machine may be in or less than the micrometer domain. The micro machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft is operable to be driven by the micro actuator. A tool is coupled to the micro shaft and is operable to perform work in response to at least motion of the micro shaft.

Methods and systems for micro machines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stalford, Harold L.

A micro machine may be in or less than the micrometer domain. The micro machine may include a micro actuator and a micro shaft coupled to the micro actuator. The micro shaft is operable to be driven by the micro actuator. A tool is coupled to the micro shaft and is operable to perform work in response to at least motion of the micro shaft.

Accessible engineering drawings for visually impaired machine operators.

PubMed

Ramteke, Deepak; Kansal, Gayatri; Madhab, Benu

2014-01-01

An engineering drawing provides manufacturing information to a machine operator. An operator plans and executes machining operations based on this information. A visually impaired (VI) operator does not have direct access to the drawings. Drawing information is provided to them verbally or by using sample parts. Both methods have limitations that affect the quality of output. Use of engineering drawings is a standard practice for every industry; this hampers employment of a VI operator. Accessible engineering drawings are required to increase both independence, as well as, employability of VI operators. Today, Computer Aided Design (CAD) software is used for making engineering drawings, which are saved in CAD files. Required information is extracted from the CAD files and converted into Braille or voice. The authors of this article propose a method to make engineering drawings information directly accessible to a VI operator.

Deep learning based classification of breast tumors with shear-wave elastography.

PubMed

Zhang, Qi; Xiao, Yang; Dai, Wei; Suo, Jingfeng; Wang, Congzhi; Shi, Jun; Zheng, Hairong

2016-12-01

This study aims to build a deep learning (DL) architecture for automated extraction of learned-from-data image features from the shear-wave elastography (SWE), and to evaluate the DL architecture in differentiation between benign and malignant breast tumors. We construct a two-layer DL architecture for SWE feature extraction, comprised of the point-wise gated Boltzmann machine (PGBM) and the restricted Boltzmann machine (RBM). The PGBM contains task-relevant and task-irrelevant hidden units, and the task-relevant units are connected to the RBM. Experimental evaluation was performed with five-fold cross validation on a set of 227 SWE images, 135 of benign tumors and 92 of malignant tumors, from 121 patients. The features learned with our DL architecture were compared with the statistical features quantifying image intensity and texture. Results showed that the DL features achieved better classification performance with an accuracy of 93.4%, a sensitivity of 88.6%, a specificity of 97.1%, and an area under the receiver operating characteristic curve of 0.947. The DL-based method integrates feature learning with feature selection on SWE. It may be potentially used in clinical computer-aided diagnosis of breast cancer. Copyright © 2016 Elsevier B.V. All rights reserved.

Oil-Free Rotor Support Technologies for Long Life, Closed Cycle Brayton Turbines

NASA Technical Reports Server (NTRS)

Lucero, John M.; DellaCorte, Christopher

2004-01-01

The goal of this study is to provide technological support to ensure successful life and operation of a 50-300 kW dynamic power conversion system specifically with response to the rotor support system. By utilizing technical expertise in tribology, bearings, rotordynamic, solid lubricant coatings and extensive test facilities, valuable input for mission success is provided. A discussion of the history of closed cycle Brayton turboalternators (TA) will be included. This includes the 2 kW Mini-Brayton Rotating Unit (Mini-BRU), the 10kW Brayton Rotating Unit (BRU) and the 125 kW turboalternator-compressor (TAC) designed in mid 1970's. Also included is the development of air-cycle machines and terrestrial oil-free gas turbine power systems in the form of microturbines, specifically Capstone microturbines. A short discussion of the self-acting compliant surface hydrodynamic fluid film bearings, or foil bearings, will follow, including a short history of the load capacity advances, the NASA coatings advancements as well as design model advances. Successes in terrestrial based machines will be noted and NASA tribology and bearing research test facilities will be described. Finally, implementation of a four step integration process will be included in the discussion.

5 CFR 532.217 - Appropriated fund survey jobs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... agency shall survey the following required jobs: Job title Job grade Janitor (Light) 1 Janitor (Heavy) 2... Equipment Operator 5 Truckdriver (Medium) 6 Truckdriver (Heavy) 7 Machine Tool Operator II 8 Machine Tool Operator I 9 Carpenter 9 Electrician 10 Automotive Mechanic 10 Sheet Metal Mechanic 10 Pipefitter 10 Welder...

76 FR 30200 - Forging Machines; Extension of the Office of Management and Budget's (OMB) Approval of...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-24

...: 187,264. Estimated Cost (Operation and Maintenance): $0. IV. Public Participation--Submission of... ensures that information is in the desired format, reporting burden (time and costs) is minimal... operated valves and switches. Inspection of Forging Machines, Guards, and Point-of-Operation Protection...

Grid-connected in-stream hydroelectric generation based on the doubly fed induction machine

NASA Astrophysics Data System (ADS)

Lenberg, Timothy J.

Within the United States, there is a growing demand for new environmentally friendly power generation. This has led to a surge in wind turbine development. Unfortunately, wind is not a stable prime mover, but water is. Why not apply the advances made for wind to in-stream hydroelectric generation? One important advancement is the creation of the Doubly Fed Induction Machine (DFIM). This thesis covers the application of a gearless DFIM topology for hydrokinetic generation. After providing background, this thesis presents many of the options available for the mechanical portion of the design. A mechanical turbine is then specified. Next, a method is presented for designing a DFIM including the actual design for this application. In Chapter 4, a simulation model of the system is presented, complete with a control system that maximizes power generation based on water speed. This section then goes on to present simulation results demonstrating proper operation.

A Boltzmann machine for the organization of intelligent machines

NASA Technical Reports Server (NTRS)

Moed, Michael C.; Saridis, George N.

1989-01-01

In the present technological society, there is a major need to build machines that would execute intelligent tasks operating in uncertain environments with minimum interaction with a human operator. Although some designers have built smart robots, utilizing heuristic ideas, there is no systematic approach to design such machines in an engineering manner. Recently, cross-disciplinary research from the fields of computers, systems AI and information theory has served to set the foundations of the emerging area of the design of intelligent machines. Since 1977 Saridis has been developing an approach, defined as Hierarchical Intelligent Control, designed to organize, coordinate and execute anthropomorphic tasks by a machine with minimum interaction with a human operator. This approach utilizes analytical (probabilistic) models to describe and control the various functions of the intelligent machine structured by the intuitively defined principle of Increasing Precision with Decreasing Intelligence (IPDI) (Saridis 1979). This principle, even though resembles the managerial structure of organizational systems (Levis 1988), has been derived on an analytic basis by Saridis (1988). The purpose is to derive analytically a Boltzmann machine suitable for optimal connection of nodes in a neural net (Fahlman, Hinton, Sejnowski, 1985). Then this machine will serve to search for the optimal design of the organization level of an intelligent machine. In order to accomplish this, some mathematical theory of the intelligent machines will be first outlined. Then some definitions of the variables associated with the principle, like machine intelligence, machine knowledge, and precision will be made (Saridis, Valavanis 1988). Then a procedure to establish the Boltzmann machine on an analytic basis will be presented and illustrated by an example in designing the organization level of an Intelligent Machine. A new search technique, the Modified Genetic Algorithm, is presented and proved to converge to the minimum of a cost function. Finally, simulations will show the effectiveness of a variety of search techniques for the intelligent machine.

Proposed algorithm to improve job shop production scheduling using ant colony optimization method

NASA Astrophysics Data System (ADS)

Pakpahan, Eka KA; Kristina, Sonna; Setiawan, Ari

2017-12-01

This paper deals with the determination of job shop production schedule on an automatic environment. On this particular environment, machines and material handling system are integrated and controlled by a computer center where schedule were created and then used to dictate the movement of parts and the operations at each machine. This setting is usually designed to have an unmanned production process for a specified interval time. We consider here parts with various operations requirement. Each operation requires specific cutting tools. These parts are to be scheduled on machines each having identical capability, meaning that each machine is equipped with a similar set of cutting tools therefore is capable of processing any operation. The availability of a particular machine to process a particular operation is determined by the remaining life time of its cutting tools. We proposed an algorithm based on the ant colony optimization method and embedded them on matlab software to generate production schedule which minimize the total processing time of the parts (makespan). We test the algorithm on data provided by real industry and the process shows a very short computation time. This contributes a lot to the flexibility and timelines targeted on an automatic environment.

4. VIEW OF VERTICAL BORING MACHINE. (Bullard) Vertical turning lathe ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. VIEW OF VERTICAL BORING MACHINE. (Bullard) Vertical turning lathe (VTL). Machining the fixture for GE Turboshroud. G.S. O'Brien, operator. - Juniata Shops, Machine Shop No. 1, East of Fourth Avenue at Third Street, Altoona, Blair County, PA

Whole-body Vibration Exposure of Drill Operators in Iron Ore Mines and Role of Machine-Related, Individual, and Rock-Related Factors.

PubMed

Chaudhary, Dhanjee Kumar; Bhattacherjee, Ashis; Patra, Aditya Kumar; Chau, Nearkasen

2015-12-01

This study aimed to assess the whole-body vibration (WBV) exposure among large blast hole drill machine operators with regard to the International Organization for Standardization (ISO) recommended threshold values and its association with machine- and rock-related factors and workers' individual characteristics. The study population included 28 drill machine operators who had worked in four opencast iron ore mines in eastern India. The study protocol comprised the following: measurements of WBV exposure [frequency weighted root mean square (RMS) acceleration (m/s(2))], machine-related data (manufacturer of machine, age of machine, seat height, thickness, and rest height) collected from mine management offices, measurements of rock hardness, uniaxial compressive strength and density, and workers' characteristics via face-to-face interviews. More than 90% of the operators were exposed to a higher level WBV than the ISO upper limit and only 3.6% between the lower and upper limits, mainly in the vertical axis. Bivariate correlations revealed that potential predictors of total WBV exposure were: machine manufacturer (r = 0.453, p = 0.015), age of drill (r = 0.533, p = 0.003), and hardness of rock (r = 0.561, p = 0.002). The stepwise multiple regression model revealed that the potential predictors are age of operator (regression coefficient β = -0.052, standard error SE = 0.023), manufacturer (β = 1.093, SE = 0.227), rock hardness (β = 0.045, SE = 0.018), uniaxial compressive strength (β = 0.027, SE = 0.009), and density (β = -1.135, SE = 0.235). Prevention should include using appropriate machines to handle rock hardness, rock uniaxial compressive strength and density, and seat improvement using ergonomic approaches such as including a suspension system.

Whole-body Vibration Exposure of Drill Operators in Iron Ore Mines and Role of Machine-Related, Individual, and Rock-Related Factors

PubMed Central

Chaudhary, Dhanjee Kumar; Bhattacherjee, Ashis; Patra, Aditya Kumar; Chau, Nearkasen

2015-01-01

Background This study aimed to assess the whole-body vibration (WBV) exposure among large blast hole drill machine operators with regard to the International Organization for Standardization (ISO) recommended threshold values and its association with machine- and rock-related factors and workers' individual characteristics. Methods The study population included 28 drill machine operators who had worked in four opencast iron ore mines in eastern India. The study protocol comprised the following: measurements of WBV exposure [frequency weighted root mean square (RMS) acceleration (m/s2)], machine-related data (manufacturer of machine, age of machine, seat height, thickness, and rest height) collected from mine management offices, measurements of rock hardness, uniaxial compressive strength and density, and workers' characteristics via face-to-face interviews. Results More than 90% of the operators were exposed to a higher level WBV than the ISO upper limit and only 3.6% between the lower and upper limits, mainly in the vertical axis. Bivariate correlations revealed that potential predictors of total WBV exposure were: machine manufacturer (r = 0.453, p = 0.015), age of drill (r = 0.533, p = 0.003), and hardness of rock (r = 0.561, p = 0.002). The stepwise multiple regression model revealed that the potential predictors are age of operator (regression coefficient β = −0.052, standard error SE = 0.023), manufacturer (β = 1.093, SE = 0.227), rock hardness (β = 0.045, SE = 0.018), uniaxial compressive strength (β = 0.027, SE = 0.009), and density (β = –1.135, SE = 0.235). Conclusion Prevention should include using appropriate machines to handle rock hardness, rock uniaxial compressive strength and density, and seat improvement using ergonomic approaches such as including a suspension system. PMID:26929838

Applying Failure Modes, Effects, And Criticality Analysis And Human Reliability Analysis Techniques To Improve Safety Design Of Work Process In Singapore Armed Forces

DTIC Science & Technology

2016-09-01

an instituted safety program that utilizes a generic risk assessment method involving the 5-M (Mission, Man, Machine , Medium and Management) factor...the Safety core value is hinged upon three key principles—(1) each soldier has a crucial part to play, by adopting safety as a core value and making...it a way of life in his unit; (2) safety is an integral part of training, operations and mission success, and (3) safety is an individual, team and

An Operating Environment for the Jellybean Machine

DTIC Science & Technology

1988-05-01

MODEL 48 5.4.4 Restarting a Context The operating system provides one primitive message (RESTART-CONTEXT) and two system calls (XFERID and XFER.ADDR) to...efficient, powerful services is reqired to support this "stem. To provide this supportive operating environment, I developed an operating system kernel that...serves many of the initial needs of our machine. This Jellybean Operating System Software provides an object- based storage model, where typed

Development of E-Learning Materials for Machining Safety Education

NASA Astrophysics Data System (ADS)

Nakazawa, Tsuyoshi; Mita, Sumiyoshi; Matsubara, Masaaki; Takashima, Takeo; Tanaka, Koichi; Izawa, Satoru; Kawamura, Takashi

We developed two e-learning materials for Manufacturing Practice safety education: movie learning materials and hazard-detection learning materials. Using these video and sound media, students can learn how to operate machines safely with movie learning materials, which raise the effectiveness of preparation and review for manufacturing practice. Using these materials, students can realize safety operation well. Students can apply knowledge learned in lectures to the detection of hazards and use study methods for hazard detection during machine operation using the hazard-detection learning materials. Particularly, the hazard-detection learning materials raise students‧ safety consciousness and increase students‧ comprehension of knowledge from lectures and comprehension of operations during Manufacturing Practice.

An Unusual Complication With the Administration of a Volatile Anesthetic Agent for Status Asthmaticus in the Pediatric Intensive Care Unit: Case Report and Review of the Literature.

PubMed

Shutes, Brittany; Frazier, W Joshua; Tobias, Joseph D

2017-07-01

In severe cases of status asthmaticus, when conventional therapies fail, volatile anesthetic agents remain a therapeutic option. When delivered outside of the operating room setting, specialized delivery techniques are needed to ensure the safe and effective use of volatile anesthetic agents. We present a 16-year-old adolescent with status asthmaticus who required the therapeutic administration of the volatile anesthetic agent, sevoflurane, in the pediatric intensive care unit (PICU). Although initially effective in reducing bronchospasm, progressive hypercarbia developed due to defective functioning of the carbon dioxide absorber of the anesthesia machine. This failure occurred as the soda lime compartment filled with water accumulated from circuit humidification and continuous albuterol therapy. The role of volatile anesthetic agents in the treatment of status asthmaticus in the PICU is discussed, options for delivery outside of the operating room presented, and potential problems with delivery reviewed.

System and method for cooling a superconducting rotary machine

DOEpatents

Ackermann, Robert Adolf [Schenectady, NY; Laskaris, Evangelos Trifon [Schenectady, NY; Huang, Xianrui [Clifton Park, NY; Bray, James William [Niskayuna, NY

2011-08-09

A system for cooling a superconducting rotary machine includes a plurality of sealed siphon tubes disposed in balanced locations around a rotor adjacent to a superconducting coil. Each of the sealed siphon tubes includes a tubular body and a heat transfer medium disposed in the tubular body that undergoes a phase change during operation of the machine to extract heat from the superconducting coil. A siphon heat exchanger is thermally coupled to the siphon tubes for extracting heat from the siphon tubes during operation of the machine.

Graphite fiber reinforced structure for supporting machine tools

DOEpatents

Knight, Jr., Charles E.; Kovach, Louis; Hurst, John S.

1978-01-01

Machine tools utilized in precision machine operations require tool support structures which exhibit minimal deflection, thermal expansion and vibration characteristics. The tool support structure of the present invention is a graphite fiber reinforced composite in which layers of the graphite fibers or yarn are disposed in a 0/90.degree. pattern and bonded together with an epoxy resin. The finished composite possesses a low coefficient of thermal expansion and a substantially greater elastic modulus, stiffness-to-weight ratio, and damping factor than a conventional steel tool support utilized in similar machining operations.

Quantify work load and muscle functional activation patterns in neck-shoulder muscles of female sewing machine operators using surface electromyogram.

PubMed

Zhang, Fei-Ruo; He, Li-Hua; Wu, Shan-Shan; Li, Jing-Yun; Ye, Kang-Pin; Wang, Sheng

2011-11-01

Work-related musculoskeletal disorders (WMSDs) have high prevalence in sewing machine operators employed in the garment industry. Long work duration, sustained low level work and precise hand work are the main risk factors of neck-shoulder disorders for sewing machine operators. Surface electromyogram (sEMG) offers a valuable tool to determine muscle activity (internal exposure) and quantify muscular load (external exposure). During sustained and/or repetitive muscle contractions, typical changes of muscle fatigue in sEMG, as an increase in amplitude or a decrease as a shift in spectrum towards lower frequencies, can be observed. In this paper, we measured and quantified the muscle load and muscular activity patterns of neck-shoulder muscles in female sewing machine operators during sustained sewing machine operating tasks using sEMG. A total of 18 healthy women sewing machine operators volunteered to participate in this study. Before their daily sewing machine operating task, we measured the maximal voluntary contractions (MVC) and 20%MVC of bilateral cervical erector spinae (CES) and upper trapezius (UT) respectively, then the sEMG signals of bilateral UT and CES were monitored and recorded continuously during 200 minutes of sustained sewing machine operating simultaneously which equals to 20 time windows with 10 minutes as one time window. After 200 minutes' work, we retest 20%MVC of four neck-shoulder muscles and recorded the sEMG signals. Linear analysis, including amplitude probability distribution frequency (APDF), amplitude analysis parameters such as roof mean square (RMS) and spectrum analysis parameter as median frequency (MF), were used to calculate and indicate muscle load and muscular activity of bilateral CES and UT. During 200 minutes of sewing machine operating, the median load for the left cervical erector spinae (LCES), right cervical erector spinae (RCES), left upper trapezius (LUT) and right upper trapezius (RUT) were 6.78%MVE, 6.94%MVE, 6.47%MVE and 5.68%MVE, respectively. Work load of right muscles are significantly higher than that of the left muscles (P < 0.05); sEMG signal analysis of isometric contractions indicated that the amplitude value before operating was significantly higher than that of after work (P < 0.01), and the spectrum value of bilateral CES and UT were significantly lower than those of after work (P < 0.01); according to the sEMG signal data of 20 time windows, with operating time pass by, the muscle activity patterns of bilateral CES and UT showed dynamic changes, the maximal amplitude of LCES, RCES, LUT occurred at the 20th time window, RUT at 16th time window, spectrum analysis showed that the lower value happened at 7th, 16th, 20th time windows. Female sewing machine operators were exposed to high sustained static load on bilateral neck-shoulder muscles; left neck and shoulder muscles were held in more static positions; the 7th, 16th, and 20th time windows were muscle fatigue period that ergonomics intervention can protocol at these periods.

15 CFR 5.5 - Vending machines.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 15 Commerce and Foreign Trade 1 2011-01-01 2011-01-01 false Vending machines. 5.5 Section 5.5... machines. (a) The income from any vending machines which are located within reasonable proximity to and are... shall be assigned to the operator of such stand. (b) If a vending machine vends articles of a type...

15 CFR 5.5 - Vending machines.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Vending machines. 5.5 Section 5.5... machines. (a) The income from any vending machines which are located within reasonable proximity to and are... shall be assigned to the operator of such stand. (b) If a vending machine vends articles of a type...

Creating Situational Awareness in Spacecraft Operations with the Machine Learning Approach

NASA Astrophysics Data System (ADS)

Li, Z.

2016-09-01

This paper presents a machine learning approach for the situational awareness capability in spacecraft operations. There are two types of time dependent data patterns for spacecraft datasets: the absolute time pattern (ATP) and the relative time pattern (RTP). The machine learning captures the data patterns of the satellite datasets through the data training during the normal operations, which is represented by its time dependent trend. The data monitoring compares the values of the incoming data with the predictions of machine learning algorithm, which can detect any meaningful changes to a dataset above the noise level. If the difference between the value of incoming telemetry and the machine learning prediction are larger than the threshold defined by the standard deviation of datasets, it could indicate the potential anomaly that may need special attention. The application of the machine-learning approach to the Advanced Himawari Imager (AHI) on Japanese Himawari spacecraft series is presented, which has the same configuration as the Advanced Baseline Imager (ABI) on Geostationary Environment Operational Satellite (GOES) R series. The time dependent trends generated by the data-training algorithm are in excellent agreement with the datasets. The standard deviation in the time dependent trend provides a metric for measuring the data quality, which is particularly useful in evaluating the detector quality for both AHI and ABI with multiple detectors in each channel. The machine-learning approach creates the situational awareness capability, and enables engineers to handle the huge data volume that would have been impossible with the existing approach, and it leads to significant advances to more dynamic, proactive, and autonomous spacecraft operations.

Operator-coached machine vision for space telerobotics

NASA Technical Reports Server (NTRS)

Bon, Bruce; Wilcox, Brian; Litwin, Todd; Gennery, Donald B.

1991-01-01

A prototype system for interactive object modeling has been developed and tested. The goal of this effort has been to create a system which would demonstrate the feasibility of high interactive operator-coached machine vision in a realistic task environment, and to provide a testbed for experimentation with various modes of operator interaction. The purpose for such a system is to use human perception where machine vision is difficult, i.e., to segment the scene into objects and to designate their features, and to use machine vision to overcome limitations of human perception, i.e., for accurate measurement of object geometry. The system captures and displays video images from a number of cameras, allows the operator to designate a polyhedral object one edge at a time by moving a 3-D cursor within these images, performs a least-squares fit of the designated edges to edge data detected with a modified Sobel operator, and combines the edges thus detected to form a wire-frame object model that matches the Sobel data.

[Human machines--mechanical humans? The industrial arrangement of the relation between human being and machine on the basis of psychotechnik and Georg Schlesingers work with disabled soldiers].

PubMed

Patzel-Mattern, Katja

2005-01-01

The 20th Century is the century of of technical artefacts. With their existance and use they create an artificial reality, within which humans have to position themselves. Psychotechnik is an attempt to enable humans for this positioning. It gained importance in Germany after World War I and had its heyday between 1919 and 1926. On the basis of the activity of the engineer and supporter of Psychotechnik Georg Schlesinger, whose particular interest were disabled soldiers, the essay on hand will investigate the understanding of the body and the human being of Psychotechnik as an applied science. It turned out, that the biggest achievement of Psychotechnik was to establish a new view of the relation between human being and machine. Thus it helped to show that the human-machine-interface is a shapable unit. Psychotechnik sees the human body and its physique as the last instance for the design of machines. Its main concern is to optimize the relation between human being and machine rather than to standardize human beings according to the construction of machines. After her splendid rise during the Weimar Republic and her rapid decline since the late 1920s Psychotechnik nowadays gains scientifical attention as a historical phenomenon. The main attention in the current discourse lies on the aspects conserning philosophy of science: the unity of body and soul, the understanding of the human-machine-interface as a shapable unit and the human being as a last instance of this unit.

Learning Activity Packets for Grinding Machines. Unit II--Surface Grinding.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) is one of three that accompany the curriculum guide on grinding machines. It outlines the study activities and performance tasks for the second unit of this curriculum guide. Its purpose is to aid the student in attaining a working knowledge of this area of training and in achieving a skilled or moderately…

Learning Activity Packets for Grinding Machines. Unit III--Cylindrical Grinding.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) is one of three that accompany the curriculum guide on grinding machines. It outlines the study activities and performance tasks for the third unit of this curriculum guide. Its purpose is to aid the student in attaining a working knowledge of this area of training and in achieving a skilled or moderately…

A randomized controlled trial of chair interventions on back and hip pain among sewing machine operators: the los angeles garment study.

PubMed

Wang, Pin-Chieh; Ritz, Beate R; Janowitz, Ira; Harrison, Robert J; Yu, Fei; Chan, Jacqueline; Rempel, David M

2008-03-01

Determine whether an adjustable chair with a curved or a flat seat pan improved monthly back and hip pain scores in sewing machine operators. This 4-month intervention study randomized 293 sewing machine operators with back and hip pain. The participants in the control group received a placebo intervention, and participants in the intervention groups received the placebo intervention and one of the two intervention chairs. Compared with the control group, mean pain improvement for the flat chair intervention was 0.43 points (95% CI = 0.34, 0.51) per month, and mean pain improvement for the curved chair intervention was 0.25 points (95% CI = 0.16, 0.34) per month. A height-adjustable task chair with a swivel function can reduce back and hip pain in sewing machine operators. The findings may be relevant to workers who perform visual- and hand-intensive manufacturing jobs.

Thrown object testing of forest machine operator protective structures

Treesearch

S.E. Taylor; M.W. Veal; R.B. Rummer

2003-01-01

High-speed chains or rotating disks are commonly used to cut and process trees during forest harvesting operations. Mechanical failure or fatigue of these tools can lead to a potentially hazardous situation where fragments of chain or sawteeth are thrown through the operator enclosures on forest machines. This poster presentation discusses the development and...

Visual feedback system to reduce errors while operating roof bolting machines

PubMed Central

Steiner, Lisa J.; Burgess-Limerick, Robin; Eiter, Brianna; Porter, William; Matty, Tim

2015-01-01

Problem Operators of roof bolting machines in underground coal mines do so in confined spaces and in very close proximity to the moving equipment. Errors in the operation of these machines can have serious consequences, and the design of the equipment interface has a critical role in reducing the probability of such errors. Methods An experiment was conducted to explore coding and directional compatibility on actual roof bolting equipment and to determine the feasibility of a visual feedback system to alert operators of critical movements and to also alert other workers in close proximity to the equipment to the pending movement of the machine. The quantitative results of the study confirmed the potential for both selection errors and direction errors to be made, particularly during training. Results Subjective data confirmed a potential benefit of providing visual feedback of the intended operations and movements of the equipment. Impact This research may influence the design of these and other similar control systems to provide evidence for the use of warning systems to improve operator situational awareness. PMID:23398703

Means and method of balancing multi-cylinder reciprocating machines

DOEpatents

Corey, John A.; Walsh, Michael M.

1985-01-01

A virtual balancing axis arrangement is described for multi-cylinder reciprocating piston machines for effectively balancing out imbalanced forces and minimizing residual imbalance moments acting on the crankshaft of such machines without requiring the use of additional parallel-arrayed balancing shafts or complex and expensive gear arrangements. The novel virtual balancing axis arrangement is capable of being designed into multi-cylinder reciprocating piston and crankshaft machines for substantially reducing vibrations induced during operation of such machines with only minimal number of additional component parts. Some of the required component parts may be available from parts already required for operation of auxiliary equipment, such as oil and water pumps used in certain types of reciprocating piston and crankshaft machine so that by appropriate location and dimensioning in accordance with the teachings of the invention, the virtual balancing axis arrangement can be built into the machine at little or no additional cost.

Structural health monitoring of wind turbine blades

NASA Astrophysics Data System (ADS)

Rumsey, Mark A.; Paquette, Joshua A.

2008-03-01

As electric utility wind turbines increase in size, and correspondingly, increase in initial capital investment cost, there is an increasing need to monitor the health of the structure. Acquiring an early indication of structural or mechanical problems allows operators to better plan for maintenance, possibly operate the machine in a de-rated condition rather than taking the unit off-line, or in the case of an emergency, shut the machine down to avoid further damage. This paper describes several promising structural health monitoring (SHM) techniques that were recently exercised during a fatigue test of a 9 meter glass-epoxy and carbon-epoxy wind turbine blade. The SHM systems were implemented by teams from NASA Kennedy Space Center, Purdue University and Virginia Tech. A commercial off-the-shelf acoustic emission (AE) NDT system gathered blade AE data throughout the test. At a fatigue load cycle rate around 1.2 Hertz, and after more than 4,000,000 fatigue cycles, the blade was diagnostically and visibly failing at the out-board blade spar-cap termination point at 4.5 meters. For safety reasons, the test was stopped just before the blade completely failed. This paper provides an overview of the SHM and NDT system setups and some current test results.

Challenges in Special Steel Making

NASA Astrophysics Data System (ADS)

Balachandran, G.

2018-02-01

Special bar quality [SBQ] is a long steel product where an assured quality is delivered by the steel mill to its customer. The bars have enhanced tolerance to higher stress application and it is demanded for specialised component making. The SBQ bars are sought for component making processing units such as closed die hot forging, hot extrusion, cold forging, machining, heat treatment, welding operations. The final component quality of the secondary processing units depends on the quality maintained at the steel maker end along with quality maintained at the fabricator end. Thus, quality control is ensured at every unit process stages. The various market segments catered to by SBQ steel segment is ever growing and is reviewed. Steel mills need adequate infrastructure and technological capability to make these higher quality steels. Some of the critical stages of processing SBQ and the critical quality maintenance parameters at the steel mill in the manufacture has been brought out.

Influence of guide vane opening on the flow phenomena in a pump turbine during a fast transition from pump mode to generating mode

NASA Astrophysics Data System (ADS)

Stens, C.; Riedelbauch, S.

2017-04-01

Due to a more fluctuating energy production caused by renewable energies such as wind and solar power, the number of changes between operating points in pumped storage power plants has increased over the last years. To further increase available regulating power, it is desirable to speed up these changes of operation conditions in Hydro units. Previous studies showed that CFD is well capable of predicting the flow phenomena in the machine under unsteady conditions for a large guide vane opening angle. The present paper investigates the benefits of nearly closed guide vanes during the transition. Results are compared between the two different angles as well as between simulation and measurement.

Reactive Scheduling in Multipurpose Batch Plants

NASA Astrophysics Data System (ADS)

Narayani, A.; Shaik, Munawar A.

2010-10-01

Scheduling is an important operation in process industries for improving resource utilization resulting in direct economic benefits. It has a two-fold objective of fulfilling customer orders within the specified time as well as maximizing the plant profit. Unexpected disturbances such as machine breakdown, arrival of rush orders and cancellation of orders affect the schedule of the plant. Reactive scheduling is generation of a new schedule which has minimum deviation from the original schedule in spite of the occurrence of unexpected events in the plant operation. Recently, Shaik & Floudas (2009) proposed a novel unified model for short-term scheduling of multipurpose batch plants using unit-specific event-based continuous time representation. In this paper, we extend the model of Shaik & Floudas (2009) to handle reactive scheduling.

Comparison of spike-sorting algorithms for future hardware implementation.

PubMed

Gibson, Sarah; Judy, Jack W; Markovic, Dejan

2008-01-01

Applications such as brain-machine interfaces require hardware spike sorting in order to (1) obtain single-unit activity and (2) perform data reduction for wireless transmission of data. Such systems must be low-power, low-area, high-accuracy, automatic, and able to operate in real time. Several detection and feature extraction algorithms for spike sorting are described briefly and evaluated in terms of accuracy versus computational complexity. The nonlinear energy operator method is chosen as the optimal spike detection algorithm, being most robust over noise and relatively simple. The discrete derivatives method [1] is chosen as the optimal feature extraction method, maintaining high accuracy across SNRs with a complexity orders of magnitude less than that of traditional methods such as PCA.

Apparatus for electrical-assisted incremental forming and process thereof

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roth, John; Cao, Jian

A process and apparatus for forming a sheet metal component using an electric current passing through the component. The process can include providing an incremental forming machine, the machine having at least one arcuate tipped tool and at least electrode spaced a predetermined distance from the arcuate tipped tool. The machine is operable to perform a plurality of incremental deformations on the sheet metal component using the arcuate tipped tool. The machine is also operable to apply an electric direct current through the electrode into the sheet metal component at the predetermined distance from the arcuate tipped tool while themore » machine is forming the sheet metal component.« less

[Features of the maintenance of automated developing machines].

PubMed

Koveshnikov, A I

1999-01-01

Based on his long-term own experience the author gives recommendations on the assembly, adjustment, operation, and preventive maintenance of automatic developing machines. Procedures are presented for evaluating the quality of X-ray films and controlling the activity of operating qualities of a developer while machining photographic materials. Troubles and malfunction of equipment and procedures for their elimination are shown to affect the quality of development of films.

Virtual Planning, Control, and Machining for a Modular-Based Automated Factory Operation in an Augmented Reality Environment

PubMed Central

Pai, Yun Suen; Yap, Hwa Jen; Md Dawal, Siti Zawiah; Ramesh, S.; Phoon, Sin Ye

2016-01-01

This study presents a modular-based implementation of augmented reality to provide an immersive experience in learning or teaching the planning phase, control system, and machining parameters of a fully automated work cell. The architecture of the system consists of three code modules that can operate independently or combined to create a complete system that is able to guide engineers from the layout planning phase to the prototyping of the final product. The layout planning module determines the best possible arrangement in a layout for the placement of various machines, in this case a conveyor belt for transportation, a robot arm for pick-and-place operations, and a computer numerical control milling machine to generate the final prototype. The robotic arm module simulates the pick-and-place operation offline from the conveyor belt to a computer numerical control (CNC) machine utilising collision detection and inverse kinematics. Finally, the CNC module performs virtual machining based on the Uniform Space Decomposition method and axis aligned bounding box collision detection. The conducted case study revealed that given the situation, a semi-circle shaped arrangement is desirable, whereas the pick-and-place system and the final generated G-code produced the highest deviation of 3.83 mm and 5.8 mm respectively. PMID:27271840

Virtual Planning, Control, and Machining for a Modular-Based Automated Factory Operation in an Augmented Reality Environment.

PubMed

Pai, Yun Suen; Yap, Hwa Jen; Md Dawal, Siti Zawiah; Ramesh, S; Phoon, Sin Ye

2016-06-07

This study presents a modular-based implementation of augmented reality to provide an immersive experience in learning or teaching the planning phase, control system, and machining parameters of a fully automated work cell. The architecture of the system consists of three code modules that can operate independently or combined to create a complete system that is able to guide engineers from the layout planning phase to the prototyping of the final product. The layout planning module determines the best possible arrangement in a layout for the placement of various machines, in this case a conveyor belt for transportation, a robot arm for pick-and-place operations, and a computer numerical control milling machine to generate the final prototype. The robotic arm module simulates the pick-and-place operation offline from the conveyor belt to a computer numerical control (CNC) machine utilising collision detection and inverse kinematics. Finally, the CNC module performs virtual machining based on the Uniform Space Decomposition method and axis aligned bounding box collision detection. The conducted case study revealed that given the situation, a semi-circle shaped arrangement is desirable, whereas the pick-and-place system and the final generated G-code produced the highest deviation of 3.83 mm and 5.8 mm respectively.

Virtual Planning, Control, and Machining for a Modular-Based Automated Factory Operation in an Augmented Reality Environment

NASA Astrophysics Data System (ADS)

Pai, Yun Suen; Yap, Hwa Jen; Md Dawal, Siti Zawiah; Ramesh, S.; Phoon, Sin Ye

2016-06-01

This study presents a modular-based implementation of augmented reality to provide an immersive experience in learning or teaching the planning phase, control system, and machining parameters of a fully automated work cell. The architecture of the system consists of three code modules that can operate independently or combined to create a complete system that is able to guide engineers from the layout planning phase to the prototyping of the final product. The layout planning module determines the best possible arrangement in a layout for the placement of various machines, in this case a conveyor belt for transportation, a robot arm for pick-and-place operations, and a computer numerical control milling machine to generate the final prototype. The robotic arm module simulates the pick-and-place operation offline from the conveyor belt to a computer numerical control (CNC) machine utilising collision detection and inverse kinematics. Finally, the CNC module performs virtual machining based on the Uniform Space Decomposition method and axis aligned bounding box collision detection. The conducted case study revealed that given the situation, a semi-circle shaped arrangement is desirable, whereas the pick-and-place system and the final generated G-code produced the highest deviation of 3.83 mm and 5.8 mm respectively.

Accessing and operating agricultural machinery: Advancements in assistive technology for users with impaired mobility.

PubMed

Ehlers, Shawn G; Field, William E

2018-02-14

This research focused on the advancements made in enabling agricultural workers with impaired mobility to access and operate off-road agricultural machinery. Although not a new concept, technological advancements in remote-controlled lifts, electronic actuators, electric over hydraulic controllers, and various modes of hand controls have advanced significantly, allowing operators with limited mobility to resume a high level of productivity in agricultural-related enterprises. In the United States, approximately 1.7% of the population is living with some form of paralysis or significant mobility impairment. When paired with the 2012 USDA Agriculture Census of 3.2 million farmers, it can be extrapolated that these technologies could impact 54,000 agricultural workers who have encountered disabling injuries or disease, which inhibit their ability to access and operate tractors, combines, and other self-propelled agricultural machines. Advancements in agricultural-specific technologies can allow for many of these individuals to regain the ability to effectively operate machinery once more.

30 CFR 75.1723 - Stationary grinding machines; protective devices.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Stationary grinding machines; protective....1723 Stationary grinding machines; protective devices. (a) Stationary grinding machines other than... the wheel. (3) Safety washers. (b) Grinding wheels shall be operated within the specifications of the...

30 CFR 75.1723 - Stationary grinding machines; protective devices.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Stationary grinding machines; protective....1723 Stationary grinding machines; protective devices. (a) Stationary grinding machines other than... the wheel. (3) Safety washers. (b) Grinding wheels shall be operated within the specifications of the...

Machine Shop Lathes.

ERIC Educational Resources Information Center

Dunn, James

This guide, the second in a series of five machine shop curriculum manuals, was designed for use in machine shop courses in Oklahoma. The purpose of the manual is to equip students with basic knowledge and skills that will enable them to enter the machine trade at the machine-operator level. The curriculum is designed so that it can be used in…

7 CFR 3201.41 - Metalworking fluids.

Code of Federal Regulations, 2013 CFR

2013-01-01

... feedstock during grinding and machining operations involving unusually high temperatures or corrosion... prevention when applied to metal feedstock during normal grinding and machining operations. (iii) High... percent. (3) High performance soluble, semi-synthetic, and synthetic oils—40 percent. (c) Preference...

7 CFR 3201.41 - Metalworking fluids.

Code of Federal Regulations, 2012 CFR

2012-01-01

... feedstock during grinding and machining operations involving unusually high temperatures or corrosion... prevention when applied to metal feedstock during normal grinding and machining operations. (iii) High... percent. (3) High performance soluble, semi-synthetic, and synthetic oils—40 percent. (c) Preference...

7 CFR 3201.41 - Metalworking fluids.

Code of Federal Regulations, 2014 CFR

2014-01-01

... feedstock during grinding and machining operations involving unusually high temperatures or corrosion... prevention when applied to metal feedstock during normal grinding and machining operations. (iii) High... percent. (3) High performance soluble, semi-synthetic, and synthetic oils—40 percent. (c) Preference...

Optimization process planning using hybrid genetic algorithm and intelligent search for job shop machining.

PubMed

Salehi, Mojtaba; Bahreininejad, Ardeshir

2011-08-01

Optimization of process planning is considered as the key technology for computer-aided process planning which is a rather complex and difficult procedure. A good process plan of a part is built up based on two elements: (1) the optimized sequence of the operations of the part; and (2) the optimized selection of the machine, cutting tool and Tool Access Direction (TAD) for each operation. In the present work, the process planning is divided into preliminary planning, and secondary/detailed planning. In the preliminary stage, based on the analysis of order and clustering constraints as a compulsive constraint aggregation in operation sequencing and using an intelligent searching strategy, the feasible sequences are generated. Then, in the detailed planning stage, using the genetic algorithm which prunes the initial feasible sequences, the optimized operation sequence and the optimized selection of the machine, cutting tool and TAD for each operation based on optimization constraints as an additive constraint aggregation are obtained. The main contribution of this work is the optimization of sequence of the operations of the part, and optimization of machine selection, cutting tool and TAD for each operation using the intelligent search and genetic algorithm simultaneously.

Optimization process planning using hybrid genetic algorithm and intelligent search for job shop machining

PubMed Central

Salehi, Mojtaba

2010-01-01

Optimization of process planning is considered as the key technology for computer-aided process planning which is a rather complex and difficult procedure. A good process plan of a part is built up based on two elements: (1) the optimized sequence of the operations of the part; and (2) the optimized selection of the machine, cutting tool and Tool Access Direction (TAD) for each operation. In the present work, the process planning is divided into preliminary planning, and secondary/detailed planning. In the preliminary stage, based on the analysis of order and clustering constraints as a compulsive constraint aggregation in operation sequencing and using an intelligent searching strategy, the feasible sequences are generated. Then, in the detailed planning stage, using the genetic algorithm which prunes the initial feasible sequences, the optimized operation sequence and the optimized selection of the machine, cutting tool and TAD for each operation based on optimization constraints as an additive constraint aggregation are obtained. The main contribution of this work is the optimization of sequence of the operations of the part, and optimization of machine selection, cutting tool and TAD for each operation using the intelligent search and genetic algorithm simultaneously. PMID:21845020

Unitary Shaft-Angle and Shaft-Speed Sensor Assemblies

NASA Technical Reports Server (NTRS)

Alhorn, Dean C.; Howard, David E.; Smith, Dennis A.

2006-01-01

The figure depicts a unit that contains a rotary-position or a rotary-speed sensor, plus electronic circuitry necessary for its operation, all enclosed in a single housing with a shaft for coupling to an external rotary machine. This rotation sensor unit is complete: when its shaft is mechanically connected to that of the rotary machine and it is supplied with electric power, it generates an output signal directly indicative of the rotary position or speed, without need for additional processing by other circuitry. The incorporation of all of the necessary excitatory and readout circuitry into the housing (in contradistinction to using externally located excitatory and/or readout circuitry) in a compact arrangement is the major difference between this unit and prior rotation-sensor units. The sensor assembly inside the housing includes excitatory and readout integrated circuits mounted on a circular printed-circuit board. In a typical case in which the angle or speed transducer(s) utilize electromagnetic induction, the assembly also includes another circular printed-circuit board on which the transducer windings are mounted. A sheet of high-magnetic permeability metal ("mu metal") is placed between the winding board and the electronic-circuit board to prevent spurious coupling of excitatory signals from the transducer windings to the readout circuits. The housing and most of the other mechanical hardware can be common to a variety of different sensor designs. Hence, the unit can be configured to generate any of variety of outputs by changing the interior sensor assembly. For example, the sensor assembly could contain an analog tachometer circuit that generates an output proportional (in both magnitude and sign or in magnitude only) to the speed of rotation.

Compressor and Turbine Models of Brayton Units for Space Nuclear Power Systems

NASA Astrophysics Data System (ADS)

Gallo, Bruno M.; El-Genk, Mohamed S.; Tournier, Jean-Michel

2007-01-01

Closed Brayton Cycles with centrifugal flow, single-shaft turbo-machines are being considered, with gas cooled nuclear reactors, to provide 10's to 100's of electrical power to support future space exploration missions and Lunar and Mars outposts. Such power system analysis is typically based on the cycle thermodynamics, for given operating pressures and temperatures and assumed polytropic efficiencies of the compressor and turbine of the Brayton energy conversion units. Thus the analysis results not suitable for modeling operation transients such as startup and changes in the electric load. To simulate these transients, accurate models of the turbine and compressor in the Brayton rotating unit, which calculate the changes in the compressor and turbine efficiencies with system operation are needed. This paper presents flow models that account for the design and dimensions of the compressor impeller and diffuser, and the turbine stator and rotor blades. These models calculate the various enthalpy losses and the polytropic efficiencies along with the pressure ratios of the turbine and compressor. The predictions of these models compare well with reported performance data of actual hardware. In addition, the results of a parametric analysis to map the operations of the compressor and turbine, as functions of the rotating shaft speed and inlet Mach number of the gas working fluid, are presented and discussed. The analysis used a binary mixture of He-Xe with a molecular weight of 40 g/mole as the working fluid.

Towards a generalized energy prediction model for machine tools

PubMed Central

Bhinge, Raunak; Park, Jinkyoo; Law, Kincho H.; Dornfeld, David A.; Helu, Moneer; Rachuri, Sudarsan

2017-01-01

Energy prediction of machine tools can deliver many advantages to a manufacturing enterprise, ranging from energy-efficient process planning to machine tool monitoring. Physics-based, energy prediction models have been proposed in the past to understand the energy usage pattern of a machine tool. However, uncertainties in both the machine and the operating environment make it difficult to predict the energy consumption of the target machine reliably. Taking advantage of the opportunity to collect extensive, contextual, energy-consumption data, we discuss a data-driven approach to develop an energy prediction model of a machine tool in this paper. First, we present a methodology that can efficiently and effectively collect and process data extracted from a machine tool and its sensors. We then present a data-driven model that can be used to predict the energy consumption of the machine tool for machining a generic part. Specifically, we use Gaussian Process (GP) Regression, a non-parametric machine-learning technique, to develop the prediction model. The energy prediction model is then generalized over multiple process parameters and operations. Finally, we apply this generalized model with a method to assess uncertainty intervals to predict the energy consumed to machine any part using a Mori Seiki NVD1500 machine tool. Furthermore, the same model can be used during process planning to optimize the energy-efficiency of a machining process. PMID:28652687

Towards a generalized energy prediction model for machine tools.

PubMed

Bhinge, Raunak; Park, Jinkyoo; Law, Kincho H; Dornfeld, David A; Helu, Moneer; Rachuri, Sudarsan

2017-04-01

Energy prediction of machine tools can deliver many advantages to a manufacturing enterprise, ranging from energy-efficient process planning to machine tool monitoring. Physics-based, energy prediction models have been proposed in the past to understand the energy usage pattern of a machine tool. However, uncertainties in both the machine and the operating environment make it difficult to predict the energy consumption of the target machine reliably. Taking advantage of the opportunity to collect extensive, contextual, energy-consumption data, we discuss a data-driven approach to develop an energy prediction model of a machine tool in this paper. First, we present a methodology that can efficiently and effectively collect and process data extracted from a machine tool and its sensors. We then present a data-driven model that can be used to predict the energy consumption of the machine tool for machining a generic part. Specifically, we use Gaussian Process (GP) Regression, a non-parametric machine-learning technique, to develop the prediction model. The energy prediction model is then generalized over multiple process parameters and operations. Finally, we apply this generalized model with a method to assess uncertainty intervals to predict the energy consumed to machine any part using a Mori Seiki NVD1500 machine tool. Furthermore, the same model can be used during process planning to optimize the energy-efficiency of a machining process.

National Synchrotron Light Source annual report 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hulbert, S.L.; Lazarz, N.M.

1992-04-01

This report discusses the following research conducted at NSLS: atomic and molecular science; energy dispersive diffraction; lithography, microscopy and tomography; nuclear physics; UV photoemission and surface science; x-ray absorption spectroscopy; x-ray scattering and crystallography; x-ray topography; workshop on surface structure; workshop on electronic and chemical phenomena at surfaces; workshop on imaging; UV FEL machine reviews; VUV machine operations; VUV beamline operations; VUV storage ring parameters; x-ray machine operations; x-ray beamline operations; x-ray storage ring parameters; superconducting x-ray lithography source; SXLS storage ring parameters; the accelerator test facility; proposed UV-FEL user facility at the NSLS; global orbit feedback systems; and NSLSmore » computer system.« less

49 CFR 214.341 - Roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Roadway maintenance machines. 214.341 Section 214... Roadway maintenance machines. (a) Each employer shall include in its on-track safety program specific provisions for the safety of roadway workers who operate or work near roadway maintenance machines. Those...

Preliminary Development of Real Time Usage-Phase Monitoring System for CNC Machine Tools with a Case Study on CNC Machine VMC 250

NASA Astrophysics Data System (ADS)

Budi Harja, Herman; Prakosa, Tri; Raharno, Sri; Yuwana Martawirya, Yatna; Nurhadi, Indra; Setyo Nogroho, Alamsyah

2018-03-01

The production characteristic of job-shop industry at which products have wide variety but small amounts causes every machine tool will be shared to conduct production process with dynamic load. Its dynamic condition operation directly affects machine tools component reliability. Hence, determination of maintenance schedule for every component should be calculated based on actual usage of machine tools component. This paper describes study on development of monitoring system to obtaining information about each CNC machine tool component usage in real time approached by component grouping based on its operation phase. A special device has been developed for monitoring machine tool component usage by utilizing usage phase activity data taken from certain electronics components within CNC machine. The components are adaptor, servo driver and spindle driver, as well as some additional components such as microcontroller and relays. The obtained data are utilized for detecting machine utilization phases such as power on state, machine ready state or spindle running state. Experimental result have shown that the developed CNC machine tool monitoring system is capable of obtaining phase information of machine tool usage as well as its duration and displays the information at the user interface application.

Touchable Tornadoes

ERIC Educational Resources Information Center

Gilhousen, David

2004-01-01

In this article, the author discusses a tornado-producing machine that he used in teacher-led, student assisted demonstrations in order to reinforce concepts learned during a unit on weather. The machine, or simulator, was powered by a hair dryer, fan, and cool-mist humidifier. The machine consists of a demonstration table containing a plenum box,…

14 CFR 382.3 - What do the terms in this rule mean?

Code of Federal Regulations, 2014 CFR

2014-01-01

... devices and medications. Automated airport kiosk means a self-service transaction machine that a carrier... machine means a continuous positive airway pressure machine. Department or DOT means the United States..., emotional or mental illness, and specific learning disabilities. The term physical or mental impairment...

An In-Process Surface Roughness Recognition System in End Milling Operations

ERIC Educational Resources Information Center

Yang, Lieh-Dai; Chen, Joseph C.

2004-01-01

To develop an in-process quality control system, a sensor technique and a decision-making algorithm need to be applied during machining operations. Several sensor techniques have been used in the in-process prediction of quality characteristics in machining operations. For example, an accelerometer sensor can be used to monitor the vibration of…

Milling Machine Operator: Instructor's Guide for an Adult Course.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Bureau of Secondary Curriculum Development.

The instructor's guide is for a course expected to help meet the need for trained operators in metalworking. Students successfully completing the course will be qualified for an entry-level job as a milling machine operator. The course is suitable for use in adult education programs of school districts, or in manpower development and training…

Tempest gas turbine extends EGT product line

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chellini, R.

With the introduction of the 7.8 MW (mechanical output) Tempest gas turbine, ECT has extended the company`s line of its small industrial turbines. The new Tempest machine, featuring a 7.5 MW electric output and a 33% thermal efficiency, ranks above the company`s single-shaft Typhoon gas turbine, rated 3.2 and 4.9 MW, and the 6.3 MW Tornado gas turbine. All three machines are well-suited for use in combined heat and power (CHP) plants, as demonstrated by the fact that close to 50% of the 150 Typhoon units sold are for CHP applications. This experience has induced EGT, of Lincoln, England, tomore » announce the introduction of the new gas turbine prior to completion of the testing program. The present single-shaft machine is expected to be used mainly for industrial trial cogeneration. This market segment, covering the needs of paper mills, hospitals, chemical plants, ceramic industry, etc., is a typical local market. Cogeneration plants are engineered according to local needs and have to be assisted by local organizations. For this reason, to efficiently cover the world market, EGT has selected a number of associates that will receive from Lincoln completely engineered machine packages and will engineer the cogeneration system according to custom requirements. These partners will also assist the customer and dispose locally of the spares required for maintenance operations.« less

Recognition of Banknote Fitness Based on a Fuzzy System Using Visible Light Reflection and Near-infrared Light Transmission Images.

PubMed

Kwon, Seung Yong; Pham, Tuyen Danh; Park, Kang Ryoung; Jeong, Dae Sik; Yoon, Sungsoo

2016-06-11

Fitness classification is a technique to assess the quality of banknotes in order to determine whether they are usable. Banknote classification techniques are useful in preventing problems that arise from the circulation of substandard banknotes (such as recognition failures, or bill jams in automated teller machines (ATMs) or bank counting machines). By and large, fitness classification continues to be carried out by humans, and this can cause the problem of varying fitness classifications for the same bill by different evaluators, and requires a lot of time. To address these problems, this study proposes a fuzzy system-based method that can reduce the processing time needed for fitness classification, and can determine the fitness of banknotes through an objective, systematic method rather than subjective judgment. Our algorithm was an implementation to actual banknote counting machine. Based on the results of tests on 3856 banknotes in United States currency (USD), 3956 in Korean currency (KRW), and 2300 banknotes in Indian currency (INR) using visible light reflection (VR) and near-infrared light transmission (NIRT) imaging, the proposed method was found to yield higher accuracy than prevalent banknote fitness classification methods. Moreover, it was confirmed that the proposed algorithm can operate in real time, not only in a normal PC environment, but also in an embedded system environment of a banknote counting machine.

Recognition of Banknote Fitness Based on a Fuzzy System Using Visible Light Reflection and Near-infrared Light Transmission Images

PubMed Central

Kwon, Seung Yong; Pham, Tuyen Danh; Park, Kang Ryoung; Jeong, Dae Sik; Yoon, Sungsoo

2016-01-01

Fitness classification is a technique to assess the quality of banknotes in order to determine whether they are usable. Banknote classification techniques are useful in preventing problems that arise from the circulation of substandard banknotes (such as recognition failures, or bill jams in automated teller machines (ATMs) or bank counting machines). By and large, fitness classification continues to be carried out by humans, and this can cause the problem of varying fitness classifications for the same bill by different evaluators, and requires a lot of time. To address these problems, this study proposes a fuzzy system-based method that can reduce the processing time needed for fitness classification, and can determine the fitness of banknotes through an objective, systematic method rather than subjective judgment. Our algorithm was an implementation to actual banknote counting machine. Based on the results of tests on 3856 banknotes in United States currency (USD), 3956 in Korean currency (KRW), and 2300 banknotes in Indian currency (INR) using visible light reflection (VR) and near-infrared light transmission (NIRT) imaging, the proposed method was found to yield higher accuracy than prevalent banknote fitness classification methods. Moreover, it was confirmed that the proposed algorithm can operate in real time, not only in a normal PC environment, but also in an embedded system environment of a banknote counting machine. PMID:27294940

Parameter monitoring compensation system and method

DOEpatents

Barkman, William E.; Babelay, Edwin F.; DeMint, Paul D.; Hebble, Thomas L.; Igou, Richard E.; Williams, Richard R.; Klages, Edward J.; Rasnick, William H.

1995-01-01

A compensation system for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along preprogrammed path during a machining operation utilizes sensors for gathering information at a preselected stage of a machining operation relating to an actual condition. The controller compares the actual condition to a condition which the program presumes to exist at the preselected stage and alters the program in accordance with detected variations between the actual condition and the assumed condition. Such conditions may be related to process parameters, such as a position, dimension or shape of the cutting tool or workpiece or an environmental temperature associated with the machining operation, and such sensors may be a contact or a non-contact type of sensor or a temperature transducer.

Paging memory from random access memory to backing storage in a parallel computer

DOEpatents

Archer, Charles J; Blocksome, Michael A; Inglett, Todd A; Ratterman, Joseph D; Smith, Brian E

2013-05-21

Paging memory from random access memory (`RAM`) to backing storage in a parallel computer that includes a plurality of compute nodes, including: executing a data processing application on a virtual machine operating system in a virtual machine on a first compute node; providing, by a second compute node, backing storage for the contents of RAM on the first compute node; and swapping, by the virtual machine operating system in the virtual machine on the first compute node, a page of memory from RAM on the first compute node to the backing storage on the second compute node.

Block-Module Electric Machines of Alternating Current

NASA Astrophysics Data System (ADS)

Zabora, I.

2018-03-01

The paper deals with electric machines having active zone based on uniform elements. It presents data on disk-type asynchronous electric motors with short-circuited rotors, where active elements are made by integrated technique that forms modular elements. Photolithography, spraying, stamping of windings, pressing of core and combined methods are utilized as the basic technological approaches of production. The constructions and features of operation for new electric machine - compatible electric machines-transformers are considered. Induction motors are intended for operation in hermetic plants with extreme conditions surrounding gas, steam-to-gas and liquid environment at a high temperature (to several hundred of degrees).

Joint FAM/Line Management Assessment Report on LLNL Machine Guarding Safety Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armstrong, J. J.

2016-07-19

The LLNL Safety Program for Machine Guarding is implemented to comply with requirements in the ES&H Manual Document 11.2, "Hazards-General and Miscellaneous," Section 13 Machine Guarding (Rev 18, issued Dec. 15, 2015). The primary goal of this LLNL Safety Program is to ensure that LLNL operations involving machine guarding are managed so that workers, equipment and government property are adequately protected. This means that all such operations are planned and approved using the Integrated Safety Management System to provide the most cost effective and safest means available to support the LLNL mission.

Bacteriological quality of drinks from vending machines.

PubMed Central

Hunter, P. R.; Burge, S. H.

1986-01-01

A survey on the bacteriological quality of both drinking water and flavoured drinks from coin-operated vending machines is reported. Forty-four per cent of 25 drinking water samples examined contained coliforms and 84% had viable counts of greater than 1000 organisms ml at 30 degrees C. Thirty-one flavoured drinks were examined; 6% contained coliforms and 39% had total counts greater than 1000 organisms ml. It is suggested that the D.H.S.S. code of practice on coin-operated vending machines is not being followed. It is also suggested that drinking water alone should not be dispensed from such machines. PMID:3794325

Affine Transform to Reform Pixel Coordinates of EOG Signals for Controlling Robot Manipulators Using Gaze Motions

PubMed Central

Rusydi, Muhammad Ilhamdi; Sasaki, Minoru; Ito, Satoshi

2014-01-01

Biosignals will play an important role in building communication between machines and humans. One of the types of biosignals that is widely used in neuroscience are electrooculography (EOG) signals. An EOG has a linear relationship with eye movement displacement. Experiments were performed to construct a gaze motion tracking method indicated by robot manipulator movements. Three operators looked at 24 target points displayed on a monitor that was 40 cm in front of them. Two channels (Ch1 and Ch2) produced EOG signals for every single eye movement. These signals were converted to pixel units by using the linear relationship between EOG signals and gaze motion distances. The conversion outcomes were actual pixel locations. An affine transform method is proposed to determine the shift of actual pixels to target pixels. This method consisted of sequences of five geometry processes, which are translation-1, rotation, translation-2, shear and dilatation. The accuracy was approximately 0.86° ± 0.67° in the horizontal direction and 0.54° ± 0.34° in the vertical. This system successfully tracked the gaze motions not only in direction, but also in distance. Using this system, three operators could operate a robot manipulator to point at some targets. This result shows that the method is reliable in building communication between humans and machines using EOGs. PMID:24919013

Consumer Nutrition Environments of Hospitals: An Exploratory Analysis Using the Hospital Nutrition Environment Scan for Cafeterias, Vending Machines, and Gift Shops, 2012

PubMed Central

Sallis, James F.; Swartz, Michael D.; Hoelscher, Deanna M.; Peskin, Melissa F.

2013-01-01

Introduction Hospitals are the primary worksite of over 5 million adults in the United States, and millions of meals are procured and consumed in this setting. Because many worksite nutrition initiatives use an ecological framework to improve the dietary habits of employees, the nutrition values of foods served in hospitals is receiving attention. Methods This study used the Hospital Nutrition Environment Scan for Cafeterias, Vending Machines, and Gift Shops to quantitatively describe the consumer nutrition environments of 39 hospitals in Southern California. Data were collected by visiting each facility once from February 2012 through May 2012. Results On average, hospitals achieved only 29%, 33%, and less than 1% of the total possible points for their cafeteria, vending machines, and gift shops sections, respectively; overall, hospitals scored 25% of the total possible points. Large facility size and contracted food service operations were associated with some healthy practices in hospital cafeterias, but we found no association between these variables and the sectional or overall nutrition composite scores. Conclusion The average consumer nutrition environment of hospitals in this sample was minimally conducive to healthful eating. Nutrition-related interventions are warranted in hospital settings. PMID:23823699

Consumer nutrition environments of hospitals: an exploratory analysis using the Hospital Nutrition Environment Scan for Cafeterias, Vending Machines, and Gift Shops, 2012.

PubMed

Winston, Courtney P; Sallis, James F; Swartz, Michael D; Hoelscher, Deanna M; Peskin, Melissa F

2013-07-03

Hospitals are the primary worksite of over 5 million adults in the United States, and millions of meals are procured and consumed in this setting. Because many worksite nutrition initiatives use an ecological framework to improve the dietary habits of employees, the nutrition values of foods served in hospitals is receiving attention. This study used the Hospital Nutrition Environment Scan for Cafeterias, Vending Machines, and Gift Shops to quantitatively describe the consumer nutrition environments of 39 hospitals in Southern California. Data were collected by visiting each facility once from February 2012 through May 2012. On average, hospitals achieved only 29%, 33%, and less than 1% of the total possible points for their cafeteria, vending machines, and gift shops sections, respectively; overall, hospitals scored 25% of the total possible points. Large facility size and contracted food service operations were associated with some healthy practices in hospital cafeterias, but we found no association between these variables and the sectional or overall nutrition composite scores. The average consumer nutrition environment of hospitals in this sample was minimally conducive to healthful eating. Nutrition-related interventions are warranted in hospital settings.

Investigation of roughing machining simulation by using visual basic programming in NX CAM system

NASA Astrophysics Data System (ADS)

Hafiz Mohamad, Mohamad; Nafis Osman Zahid, Muhammed

2018-03-01

This paper outlines a simulation study to investigate the characteristic of roughing machining simulation in 4th axis milling processes by utilizing visual basic programming in NX CAM systems. The selection and optimization of cutting orientation in rough milling operation is critical in 4th axis machining. The main purpose of roughing operation is to approximately shape the machined parts into finished form by removing the bulk of material from workpieces. In this paper, the simulations are executed by manipulating a set of different cutting orientation to generate estimated volume removed from the machine parts. The cutting orientation with high volume removal is denoted as an optimum value and chosen to execute a roughing operation. In order to run the simulation, customized software is developed to assist the routines. Operations build-up instructions in NX CAM interface are translated into programming codes via advanced tool available in the Visual Basic Studio. The codes is customized and equipped with decision making tools to run and control the simulations. It permits the integration with any independent program files to execute specific operations. This paper aims to discuss about the simulation program and identifies optimum cutting orientations for roughing processes. The output of this study will broaden up the simulation routines performed in NX CAM systems.

Design and experiment on 2KF-15 type disc cutter and shallow fertilization machine in rubber plantation

NASA Astrophysics Data System (ADS)

Deng, Yiguo; Zhang, Yuan; Wang, Yeqin

2017-12-01

At present, the trenching and fertilization machine has a serious weed plug problem when trenching and fertilization operation in rubber plantation. So a disc cutter and shallow fertilization machine in rubber plantation named 2KF-15 was designed, the design scheme used the front disc cutter cutting the grass, while using the rear of the disc furrow to trenching, the prototype of a disc anti-plugging trenching and shallow fertilization machine was completed. Afterwards, a series of trenching and fertilization field experiments were carried out, and the results showed that the ditching depth of this machine could achieve from 131 to 176 mm, and the average depth could reach 156 mm, the ditching depth stability coefficient could achieve 90.3%; The fertilizer amount of this machine could achieve from 113.2 to 156.4 kg/hm2, the average fertilizer amount reach 134.2kg/hm2, the fertilizer amount stability coefficient could achieve 89.6%, the fertilizer broken rate was 0%, the fertilizer coverage rate of 98.4%;The situation of fertilizer accumulation occurred less by using this machine, and the fertilization performance was relatively stable. This new designed machine for trenching, fertilization and covering the soil were carried out at the same time. So the number of operations could be effectively reduced. This new designed machine does not only meet the agronomic requirements of rubber plantation fertilization, but also provides a reference for the trenching and fertilization operation in other.

Noise characteristics of grass-trimming machine engines and their effect on operators.

PubMed

Mallick, Zulquernain; Badruddin, Irfan Anjum; Khaleed Hussain, M T; Salman Ahmed, N J; Kanesan, Jeevan

2009-01-01

Over the last few years, interaction of humans with noisy power-driven agricultural tools and its possible adverse after effects have been realized. Grass-trimmer engine is the primary source of noise and the use of motorized cutter, spinning at high speed, is the secondary source of noise to which operators are exposed. In the present study, investigation was carried out to determine the effect of two types of grass-trimming machine engines (SUM 328 SE and BG 328) noise on the operators in real working environment. It was found that BG-328 and SUM-328 SE produced high levels of noise, of the order of 100 and 105 dB(A), respectively, to which operators are exposed while working. It was also observed that situation aggravates when a number of operators simultaneously operate resulting in still higher levels of noise. Operators should be separated 15 meters from each other in order to avoid the combined level of noise exposure while working with these machines. It was found that SPL, of the grass-trimmer machine engines (BG-328 and SUM-328 SE), were higher than the limit of noise recommended by ISO, NIOSH, and OSHA for an 8-hour workday. Such a high level of noise exposure may cause physiological and psychological problems to the operators in long run.

Design and Construction Multi Output Power Transmition with Single Prime Mover on Agricultural Products Machine

NASA Astrophysics Data System (ADS)

Koten, V. K.; Tanamal, C. E.

2017-03-01

Manufacturing agricultural products by the farmers, people or person who involve in medium industry, small industry, and households industry still be done in separately. Although the power on primemover is enough, in operations, primemover was only to move one of several agricultural products machine. This study attempts to design and construct power transmition multi output with single primemover; a single construction that allows primemover move some agricultur products machine in the same or not. This study begins with the determination of production capacity and the power to destroy products, the determination of resources and rotation, normalization of resources and rotation, the determination of the type material used, the size determination of each machine elements, construction machine elements, and assemble machine elements into a construction multi output power transmition with single primemover on agricultural products machine. The results show that with a input normalization 4 PK (2984 Watt), rotation 2000 rpm, the strength of material 60 kg/mm2, and several operating consideration, thus obtained size of machine elements through calculation. Based on the size, the machine elements is made through the use of some machine tools and assembled to form a multi output power transmition with single primemover.

41 CFR 101-25.106 - Servicing of office machines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... inventory in relation to operating needs; i.e., availability of reserve machine in case of breakdown; (9... machines. 101-25.106 Section 101-25.106 Public Contracts and Property Management Federal Property...-General Policies § 101-25.106 Servicing of office machines. (a) The determination as to whether office...

29 CFR 570.62 - Occupations involved in the operation of bakery machines (Order 11).

Code of Federal Regulations, 2013 CFR

2013-07-01

..., or cleaning any horizontal or vertical dough mixer; batter mixer; bread dividing, rounding, or molding machine; dough brake; dough sheeter; combination bread slicing and wrapping machine; or cake cutting band saw. (2) The occupation of setting up or adjusting a cookie or cracker machine. (b...

29 CFR 570.62 - Occupations involved in the operation of bakery machines (Order 11).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., or cleaning any horizontal or vertical dough mixer; batter mixer; bread dividing, rounding, or molding machine; dough brake; dough sheeter; combination bread slicing and wrapping machine; or cake cutting band saw. (2) The occupation of setting up or adjusting a cookie or cracker machine. (b...

29 CFR 570.62 - Occupations involved in the operation of bakery machines (Order 11).

Code of Federal Regulations, 2011 CFR

2011-07-01

..., or cleaning any horizontal or vertical dough mixer; batter mixer; bread dividing, rounding, or molding machine; dough brake; dough sheeter; combination bread slicing and wrapping machine; or cake cutting band saw. (2) The occupation of setting up or adjusting a cookie or cracker machine. (b...

29 CFR 570.62 - Occupations involved in the operation of bakery machines (Order 11).

Code of Federal Regulations, 2012 CFR

2012-07-01

..., or cleaning any horizontal or vertical dough mixer; batter mixer; bread dividing, rounding, or molding machine; dough brake; dough sheeter; combination bread slicing and wrapping machine; or cake cutting band saw. (2) The occupation of setting up or adjusting a cookie or cracker machine. (b...

Your Sewing Machine.

ERIC Educational Resources Information Center

Peacock, Marion E.

The programed instruction manual is designed to aid the student in learning the parts, uses, and operation of the sewing machine. Drawings of sewing machine parts are presented, and space is provided for the student's written responses. Following an introductory section identifying sewing machine parts, the manual deals with each part and its…

Failure study of helium-cooled tungsten divertor plasma-facing units tested at DEMO relevant steady-state heat loads

NASA Astrophysics Data System (ADS)

Ritz, G.; Hirai, T.; Norajitra, P.; Reiser, J.; Giniyatulin, R.; Makhankov, A.; Mazul, I.; Pintsuk, G.; Linke, J.

2009-12-01

Tungsten was selected as armor material for the helium-cooled divertor in future DEMO-type fusion reactors and fusion power plants. After realizing the design and testing of them under cyclic thermal loads of up to ~14 MW m-2, the tungsten divertor plasma-facing units were examined by metallography; they revealed failures such as cracks at the thermal loaded and as-machined surfaces, as well as degradation of the brazing layers. Furthermore, in order to optimize the machining processes, the quality of tungsten surfaces prepared by turning, milling and using a diamond cutting wheel were examined. This paper presents a metallographic examination of the tungsten plasma-facing units as well as technical studies and the characterization on machining of tungsten and alternative brazing joints.

State machine analysis of sensor data from dynamic processes

DOEpatents

Cook, William R.; Brabson, John M.; Deland, Sharon M.

2003-12-23

A state machine model analyzes sensor data from dynamic processes at a facility to identify the actual processes that were performed at the facility during a period of interest for the purpose of remote facility inspection. An inspector can further input the expected operations into the state machine model and compare the expected, or declared, processes to the actual processes to identify undeclared processes at the facility. The state machine analysis enables the generation of knowledge about the state of the facility at all levels, from location of physical objects to complex operational concepts. Therefore, the state machine method and apparatus may benefit any agency or business with sensored facilities that stores or manipulates expensive, dangerous, or controlled materials or information.

MULTIPLE SHAFT TOOL HEAD

DOEpatents

Colbert, H.P.

1962-10-23

An improved tool head arrangement is designed for the automatic expanding of a plurality of ferruled tubes simultaneously. A plurality of output shafts of a multiple spindle drill head are driven in unison by a hydraulic motor. A plurality of tube expanders are respectively coupled to the shafts through individual power train arrangements. The axial or thrust force required for the rolling operation is provided by a double acting hydraulic cylinder having a hollow through shaft with the shaft cooperating with an internally rotatable splined shaft slidably coupled to a coupling rigidly attached to the respectlve output shaft of the drill head, thereby transmitting rotary motion and axial thrust simultaneously to the tube expander. A hydraulic power unit supplies power to each of the double acting cylinders through respective two-position, four-way valves, under control of respective solenoids for each of the cylinders. The solenoids are in turn selectively controlled by a tool selection control unit which in turn is controlled by signals received from a programmed, coded tape from a tape reader. The number of expanders that are extended in a rolling operation, which may be up to 42 expanders, is determined by a predetermined program of operations depending upon the arrangement of the ferruled tubes to be expanded in the tube bundle. The tape reader also supplies dimensional information to a machine tool servo control unit for imparting selected, horizontal and/or vertical movement to the tool head assembly. (AEC)

4. Credit JPL. Original 4" x 5" black and white ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Credit JPL. Original 4" x 5" black and white negative housed in the JPL Archives, Pasadena, California. This interior view displays the machine shop in the Administration/Shops Building (the compass angle of the view is undetermined). Looking clockwise from the lower left, the machine tools in view are a power hacksaw, a heat-treatment oven (with white gloves on top), a large hydraulic press with a tool grinder at its immediate right; along the wall in the back of the view are various unidentified machine tool attachments and a vertical milling machine. In the background, a machinist is operating a radial drilling machine, to the right of which is a small drill press. To the lower right, another machinist is operating a Pratt & Whitney engine lathe; behind the operator stand a workbench and vertical bandsaw (JPL negative no. 384-10939, 29 July 1975). - Jet Propulsion Laboratory Edwards Facility, Administration & Shops Building, Edwards Air Force Base, Boron, Kern County, CA

Robotic edge machining using elastic abrasive tool

NASA Astrophysics Data System (ADS)

Sidorova, A. V.; Semyonov, E. N.; Belomestnykh, A. S.

2018-03-01

The article describes a robotic center designed for automation of finishing operations, and analyzes technological aspects of an elastic abrasive tool applied for edge machining. Based on the experimental studies, practical recommendations on the application of the robotic center for finishing operations were developed.

Behavioral Profiling of Scada Network Traffic Using Machine Learning Algorithms

DTIC Science & Technology

2014-03-27

BEHAVIORAL PROFILING OF SCADA NETWORK TRAFFIC USING MACHINE LEARNING ALGORITHMS THESIS Jessica R. Werling, Captain, USAF AFIT-ENG-14-M-81 DEPARTMENT...subject to copyright protection in the United States. AFIT-ENG-14-M-81 BEHAVIORAL PROFILING OF SCADA NETWORK TRAFFIC USING MACHINE LEARNING ...AFIT-ENG-14-M-81 BEHAVIORAL PROFILING OF SCADA NETWORK TRAFFIC USING MACHINE LEARNING ALGORITHMS Jessica R. Werling, B.S.C.S. Captain, USAF Approved

Performance Analyses of 38 kWe Turbo-Machine Unit for Space Reactor Power Systems

NASA Astrophysics Data System (ADS)

Gallo, Bruno M.; El-Genk, Mohamed S.

2008-01-01

This paper developed a design and investigated the performance of 38 kWe turbo-machine unit for space nuclear reactor power systems with Closed Brayton Cycle (CBC) energy conversion. The compressor and turbine of this unit are scaled versions of the NASA's BRU developed in the sixties and seventies. The performance results of turbo-machine unit are calculated for rotational speed up to 45 krpm, variable reactor thermal power and system pressure, and fixed turbine and compressor inlet temperatures of 1144 K and 400 K. The analyses used a detailed turbo-machine model developed at the University of New Mexico that accounts for the various energy losses in the compressor and turbine and the effect of compressibility of the He-Xe (40 mole/g) working fluid with increased flow rate. The model also accounts for the changes in the physical and transport properties of the working fluid with temperature and pressure. Results show that a unit efficiency of 24.5% is achievable at rotation speed of 45 krpm and system pressure of 0.75 MPa, assuming shaft and electrical generator efficiencies of 86.7% and 90%. The corresponding net electric power output of the unit is 38.5 kWe, the flow rate of the working fluid is 1.667 kg/s, the pressure ratio and polytropic efficiency for the compressor are 1.60 and 83.1%, and 1.51 and 88.3% for the turbine.

VML 3.0 Reactive Sequencing Objects and Matrix Math Operations for Attitude Profiling

NASA Technical Reports Server (NTRS)

Grasso, Christopher A.; Riedel, Joseph E.

2012-01-01

VML (Virtual Machine Language) has been used as the sequencing flight software on over a dozen JPL deep-space missions, most recently flying on GRAIL and JUNO. In conjunction with the NASA SBIR entitled "Reactive Rendezvous and Docking Sequencer", VML version 3.0 has been enhanced to include object-oriented element organization, built-in queuing operations, and sophisticated matrix / vector operations. These improvements allow VML scripts to easily perform much of the work that formerly would have required a great deal of expensive flight software development to realize. Autonomous turning and tracking makes considerable use of new VML features. Profiles generated by flight software are managed using object-oriented VML data constructs executed in discrete time by the VML flight software. VML vector and matrix operations provide the ability to calculate and supply quaternions to the attitude controller flight software which produces torque requests. Using VML-based attitude planning components eliminates flight software development effort, and reduces corresponding costs. In addition, the direct management of the quaternions allows turning and tracking to be tied in with sophisticated high-level VML state machines. These state machines provide autonomous management of spacecraft operations during critical tasks like a hypothetic Mars sample return rendezvous and docking. State machines created for autonomous science observations can also use this sort of attitude planning system, allowing heightened autonomy levels to reduce operations costs. VML state machines cannot be considered merely sequences - they are reactive logic constructs capable of autonomous decision making within a well-defined domain. The state machine approach enabled by VML 3.0 is progressing toward flight capability with a wide array of applicable mission activities.

Engineering of Impulse Mechanism for Mechanical Hander Power Tools

NASA Astrophysics Data System (ADS)

Nikolaevich Drozdov, Anatoliy

2018-03-01

The solution to the problem of human security in cities should be considered on the basis of an integrated and multidisciplinary approach, including issues of security and ecology in the application of technical means used to ensure the viability and development of technocracy. In this regard, an important task is the creation of a safe technique with improved environmental properties with high technological characteristics. This primarily relates to mechanised tool — the division of technological machines with built in engines is that their weight is fully or partially perceived by the operator’s hands, making the flow and control of the car. For this subclass of machines is characterized by certain features: a built-in motor, perception of at least part of their weight by the operator during the work, the implementation of feeding and management at the expense of the muscular power of the operator. Therefore, among the commonly accepted technical and economic characteristics, machines in this case, important ergonomic (ergonomics), regulation of levels which ensures the safety of the operator. To ergonomics include vibration, noise characteristics, mass, and force feeding machine operator. Vibration is a consequence of the dynamism of the system operator machine - processed object (environment) in which the engine energy is redistributed among all the structures, causing their instability. In the machine vibration caused by technological and constructive (transformative mechanisms) unbalance of individual parts of the drive, the presence of technological and design (impact mechanisms) clearances and other reasons. This article describes a new design of impulse mechanism for hander power tools (wrenches, screwdrivers) with enhanced torque. The article substantiates a simulation model of dynamic compression process in an operating chamber during impact, provides simulation results and outlines further lines of research.

Graphic Arts--Offset Press Operator/Duplicating Machine. TI-622. Instructor's Manual and Student Learning Activity Guide.

ERIC Educational Resources Information Center

Michelsen, Robert F.

This instructor's manual and student learning activity guide comprise a kit for a graphic arts activity on offset press operator/duplicating machine. Purpose stated for the activity is to provide the student with an understanding of the basic operation involved in the production of printed matter in the graphic communications industry through the…

Universal Tool Grinder Operator Instructor's Guide. Part of Single-Tool Skills Program Machine Industries Occupations.

ERIC Educational Resources Information Center

New York State Education Dept., Albany. Div. of Curriculum Development.

The document is an instructor's guide for a course on universal tool grinder operation. The course is designed to train people in making complicated machine setups and precision in the grinding operations and, although intended primarily for adult learners, it can be adapted for high school use. The guide is divided into three parts: (1) the…

TRUFLO GONDOLA, USED WITH THE HUNTER 10 MOLDING MACHINE, OPERATES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

TRUFLO GONDOLA, USED WITH THE HUNTER 10 MOLDING MACHINE, OPERATES THE SAME AS THE TWO LARGER TRUFLOS USED IN CONJUNCTION WITH THE TWO HUNTER 20S. EACH GONDOLA IS CONNECTED TO THE NEXT AND RIDES ON A SINGLE TRACK RAIL FROM MOLDING MACHINES THROUGH POURING AREAS CARRYING A MOLD AROUND TWICE BEFORE THE MOLD IS PUSHED OFF ONTO A VIBRATING SHAKEOUT CONVEYOR. - Southern Ductile Casting Company, Casting, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

Selecting a Benchmark Suite to Profile High-Performance Computing (HPC) Machines

DTIC Science & Technology

2014-11-01

architectures. Machines now contain central processing units (CPUs), graphics processing units (GPUs), and many integrated core ( MIC ) architecture all...evaluate the feasibility and applicability of a new architecture just released to the market . Researchers are often unsure how available resources will...architectures. Having a suite of programs running on different architectures, such as GPUs, MICs , and CPUs, adds complexity and technical challenges

Simple Machine Junk Cars

ERIC Educational Resources Information Center

Herald, Christine

2010-01-01

During the month of May, the author's eighth-grade physical science students study the six simple machines through hands-on activities, reading assignments, videos, and notes. At the end of the month, they can easily identify the six types of simple machine: inclined plane, wheel and axle, pulley, screw, wedge, and lever. To conclude this unit,…

Multicenter Comparison of Machine Learning Methods and Conventional Regression for Predicting Clinical Deterioration on the Wards.

PubMed

Churpek, Matthew M; Yuen, Trevor C; Winslow, Christopher; Meltzer, David O; Kattan, Michael W; Edelson, Dana P

2016-02-01

Machine learning methods are flexible prediction algorithms that may be more accurate than conventional regression. We compared the accuracy of different techniques for detecting clinical deterioration on the wards in a large, multicenter database. Observational cohort study. Five hospitals, from November 2008 until January 2013. Hospitalized ward patients None Demographic variables, laboratory values, and vital signs were utilized in a discrete-time survival analysis framework to predict the combined outcome of cardiac arrest, intensive care unit transfer, or death. Two logistic regression models (one using linear predictor terms and a second utilizing restricted cubic splines) were compared to several different machine learning methods. The models were derived in the first 60% of the data by date and then validated in the next 40%. For model derivation, each event time window was matched to a non-event window. All models were compared to each other and to the Modified Early Warning score, a commonly cited early warning score, using the area under the receiver operating characteristic curve (AUC). A total of 269,999 patients were admitted, and 424 cardiac arrests, 13,188 intensive care unit transfers, and 2,840 deaths occurred in the study. In the validation dataset, the random forest model was the most accurate model (AUC, 0.80 [95% CI, 0.80-0.80]). The logistic regression model with spline predictors was more accurate than the model utilizing linear predictors (AUC, 0.77 vs 0.74; p < 0.01), and all models were more accurate than the MEWS (AUC, 0.70 [95% CI, 0.70-0.70]). In this multicenter study, we found that several machine learning methods more accurately predicted clinical deterioration than logistic regression. Use of detection algorithms derived from these techniques may result in improved identification of critically ill patients on the wards.

National Synchrotron Light Source annual report 1991. Volume 1, October 1, 1990--September 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hulbert, S.L.; Lazarz, N.M.

1992-04-01

This report discusses the following research conducted at NSLS: atomic and molecular science; energy dispersive diffraction; lithography, microscopy and tomography; nuclear physics; UV photoemission and surface science; x-ray absorption spectroscopy; x-ray scattering and crystallography; x-ray topography; workshop on surface structure; workshop on electronic and chemical phenomena at surfaces; workshop on imaging; UV FEL machine reviews; VUV machine operations; VUV beamline operations; VUV storage ring parameters; x-ray machine operations; x-ray beamline operations; x-ray storage ring parameters; superconducting x-ray lithography source; SXLS storage ring parameters; the accelerator test facility; proposed UV-FEL user facility at the NSLS; global orbit feedback systems; and NSLSmore » computer system.« less

Position feedback control system

DOEpatents

Bieg, Lothar F.; Jokiel, Jr., Bernhard; Ensz, Mark T.; Watson, Robert D.

2003-01-01

Disclosed is a system and method for independently evaluating the spatial positional performance of a machine having a movable member, comprising an articulated coordinate measuring machine comprising: a first revolute joint; a probe arm, having a proximal end rigidly attached to the first joint, and having a distal end with a probe tip attached thereto, wherein the probe tip is pivotally mounted to the movable machine member; a second revolute joint; a first support arm serially connecting the first joint to the second joint; and coordinate processing means, operatively connected to the first and second revolute joints, for calculating the spatial coordinates of the probe tip; means for kinematically constraining the articulated coordinate measuring machine to a working surface; and comparator means, in operative association with the coordinate processing means and with the movable machine, for comparing the true position of the movable machine member, as measured by the true position of the probe tip, with the desired position of the movable machine member.

Parameter monitoring compensation system and method

DOEpatents

Barkman, W.E.; Babelay, E.F.; DeMint, P.D.; Hebble, T.L.; Igou, R.E.; Williams, R.R.; Klages, E.J.; Rasnick, W.H.

1995-02-07

A compensation system is described for a computer-controlled machining apparatus having a controller and including a cutting tool and a workpiece holder which are movable relative to one another along a preprogrammed path during a machining operation. It utilizes sensors for gathering information at a preselected stage of a machining operation relating to an actual condition. The controller compares the actual condition to a condition which the program presumes to exist at the preselected stage and alters the program in accordance with detected variations between the actual condition and the assumed condition. Such conditions may be related to process parameters, such as a position, dimension or shape of the cutting tool or workpiece or an environmental temperature associated with the machining operation, and such sensors may be a contact or a non-contact type of sensor or a temperature transducer. 7 figs.

Machine safety: proper safeguarding techniques.

PubMed

Martin, K J

1992-06-01

1. OSHA mandates certain safeguarding of machinery to prevent accidents and protect machine operators. OSHA specifies moving parts that must be guarded and sets criteria for the guards. 2. A 1989 OSHA standard for lockout/tagout requires locking the energy source during maintenance, periodically inspecting for power transmission, and training maintenance workers. 3. In an amputation emergency, first aid for cardiopulmonary resuscitation, shock, and bleeding are the first considerations. The amputated part should be wrapped in moist gauze, placed in a sealed plastic bag, and placed in a container of 50% water and 50% ice for transport. 4. The role of the occupational health nurse in machine safety is to conduct worksite analyses to identify proper safeguarding and to communicate deficiencies to appropriate personnel; to train workers in safe work practices and observe compliance in the use of machine guards; to provide care to workers injured by machines; and to reinforce safe work practices among machine operators.

Looking west at Machine Shop (Bldg. 163) south bay interior. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Looking west at Machine Shop (Bldg. 163) south bay interior. Note the Shaw 15-ton bridge crane. This portion of the building housed machine tools and locomotive component repair functions that supported the erecting shop operations - Atchison, Topeka, Santa Fe Railroad, Albuquerque Shops, Machine Shop, 908 Second Street, Southwest, Albuquerque, Bernalillo County, NM

29 CFR 570.61 - Occupations in the operation of power-driven meat-processing machines and occupations involving...

Code of Federal Regulations, 2011 CFR

2011-07-01

... machines. (3) All occupations involved in tankage or rendering of dead animals, animal offal, animal fats..., and hashing machines; and presses (except belly-rolling machines). Except, the provisions of this.... Rendering plants means establishments engaged in the conversion of dead animals, animal offal, animal fats...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

40 CFR 63.1543 - Standards for process and process fugitive sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... paragraphs (a)(1) through (9) of this section. (1) Sinter machine; (2) Blast furnace; (3) Dross furnace; (4... machine charging location; (7) Sinter machine discharge end; (8) Sinter crushing and sizing equipment; and (9) Sinter machine area. (b) No owner or operator of any existing, new, or reconstructed primary lead...

US Navy Littoral Combat Ship (LCS) Capabilities, Risks, Possible Missions, and Modules to Support Future USMC Operating Concepts

DTIC Science & Technology

2011-07-29

squad Armament: M60 7 .62mm machine gun , MK19 40mm, M2 .50 caL machine gun 61 "Spartan Scout Unmanned Surface Vehicle (USV)," Defense Industry...1) RQ-8B Fire Scout helicopter (VTUAV) a) EO/IR/LD sensor and datalink relay 2) MH-60R/S helicopters a) GAU 16/19 machine gun b) AGM-114 Hellfire...60Rhelicopter car1ies the a .50 caliber OAU 16/A machine gun , a crew-served, recoil operated, belt-fed, air cooled, percussion fired weapon, with a rate of fire

Numerical study on the variation of pressure on India Bhabha Atomic Research Center (BARC) and Imperial College plasma focus machines

NASA Astrophysics Data System (ADS)

Singh, Arwinder; Heoh, Saw Sor; Sing, Lee

2017-03-01

In this paper, we use Lee's 5 phase model code to configure both the India Bhabha Atomic Research Center (BARC) Plasma focus machine operating in the pressure (P0) range from 1 Torr to 14 Torr as well as the Imperial College Plasma Focus Machine operating in the pressure (P0) range from 0.5 Torr to 6 Torr to compare the computational neutron yield to the experimental neutron yield as well as to obtain the relationship between axial speed va, radial shock speed vs, piston speed vp and pinch temperature with P0 for these machines.

Diversity in the association between occupation and lung cancer among black and white men.

PubMed

Swanson, G M; Lin, C S; Burns, P B

1993-01-01

A population-based case comparison study of incident lung cancer and occupational risk factors was conducted in the tricounty Detroit metropolitan area. Nearly 6000 lung cancer cases and a comparison group of 3600 colon cancer cases were interviewed. This report includes 3792 white and black male lung cancer cases and 1966 black and white colon cancer referents. Cigarette smoking, age at diagnosis, and lifetime work history were assessed to determine the relationship between length of employment in specific occupations and industries and lung cancer. Diverse patterns of association between work history and lung cancer were observed for black and white men. Significant associations were seen between lung cancer and increasing length of employment in the following occupations: for white men, concrete and terrazzo finishers, grinding machine operators, heat treating machine operators, miscellaneous machine operators, truck drivers, driver sales, and laborers; for black men, farm workers, automobile mechanics, painting machine operators, furnace operators, and garbage collectors; for both black and white men, farmers, slicing and cutting machine operators, and garbage collectors. Distinct patterns for black and white men also were observed for length of employment by industry. This study clearly demonstrates the need to include black men in studies of occupational cancer etiology and to evaluate black and white men separately. It also indicates the necessity for cigarette smoking history to accurately assess workplace cancer risks. We propose guidelines for incorporating the use of biomarkers into further studies of occupational cancer epidemiology.

Impact of an engineering design-based curriculum compared to an inquiry-based curriculum on fifth graders' content learning of simple machines

NASA Astrophysics Data System (ADS)

Marulcu, Ismail; Barnett, Michael

2016-01-01

Background: Elementary Science Education is struggling with multiple challenges. National and State test results confirm the need for deeper understanding in elementary science education. Moreover, national policy statements and researchers call for increased exposure to engineering and technology in elementary science education. The basic motivation of this study is to suggest a solution to both improving elementary science education and increasing exposure to engineering and technology in it. Purpose/Hypothesis: This mixed-method study examined the impact of an engineering design-based curriculum compared to an inquiry-based curriculum on fifth graders' content learning of simple machines. We hypothesize that the LEGO-engineering design unit is as successful as the inquiry-based unit in terms of students' science content learning of simple machines. Design/Method: We used a mixed-methods approach to investigate our research questions; we compared the control and the experimental groups' scores from the tests and interviews by using Analysis of Covariance (ANCOVA) and compared each group's pre- and post-scores by using paired t-tests. Results: Our findings from the paired t-tests show that both the experimental and comparison groups significantly improved their scores from the pre-test to post-test on the multiple-choice, open-ended, and interview items. Moreover, ANCOVA results show that students in the experimental group, who learned simple machines with the design-based unit, performed significantly better on the interview questions. Conclusions: Our analyses revealed that the design-based Design a people mover: Simple machines unit was, if not better, as successful as the inquiry-based FOSS Levers and pulleys unit in terms of students' science content learning.

Test and demonstration of a 1-MW wellhead generator: helical screw expander power plant, Model 76-1. Final report to the International Energy Agency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1985-07-04

A 1-MW geothermal wellhead power plant incorporating a Lysholm or helical screw expander (HSE) was field tested between 1980 and 1983 by Mexico, Italy, and New Zealand with technical assistance from the United States. The objectives were to provide data on the reliability and performance of the HSE and to assess the costs and benefits of its use. The range of conditions under which the HSE was tested included loads up to 933 kW, mass flowrates of 14,600 to 395, 000 lbs/hr, inlet pressures of 64 to 220 psia, inlet qualities of 0 to 100%, exhaust pressures of 3.1 tomore » 40 psia, total dissolved solids up to 310,000 ppM, and noncondensible gases up to 38% of the vapor mass flow. Typical machine efficiencies of 40 to 50% were calculated. For most operations efficiency increased approximately logarithmically with shaft power, while inlet quality and rotor speed had only small effects. The HSE was designed with oversized internal clearances in the expectation that adherent scale would form during operation. Improvements in machine efficiency of 3.5 to 4 percentage points were observed over some test periods with some scale deposition. A comparison with a 1-MW back-pressure turbine showed that the HSE can compete favorably under certain conditions. The HSE was found to be a rugged energy conversion machine for geothermal applications, but some subsystems were found to require further development. 7 refs., 28 figs., 5 tabs.« less

AC Loss Analysis of MgB2-Based Fully Superconducting Machines

NASA Astrophysics Data System (ADS)

Feddersen, M.; Haran, K. S.; Berg, F.

2017-12-01

Superconducting electric machines have shown potential for significant increase in power density, making them attractive for size and weight sensitive applications such as offshore wind generation, marine propulsion, and hybrid-electric aircraft propulsion. Superconductors exhibit no loss under dc conditions, though ac current and field produce considerable losses due to hysteresis, eddy currents, and coupling mechanisms. For this reason, many present machines are designed to be partially superconducting, meaning that the dc field components are superconducting while the ac armature coils are conventional conductors. Fully superconducting designs can provide increases in power density with significantly higher armature current; however, a good estimate of ac losses is required to determine the feasibility under the machines intended operating conditions. This paper aims to characterize the expected losses in a fully superconducting machine targeted towards aircraft, based on an actively-shielded, partially superconducting machine from prior work. Various factors are examined such as magnet strength, operating frequency, and machine load to produce a model for the loss in the superconducting components of the machine. This model is then used to optimize the design of the machine for minimal ac loss while maximizing power density. Important observations from the study are discussed.

2011 International Infantry and Joint Services Small Arms Systems Symposium, Exhibition and Firing Demonstration

DTIC Science & Technology

2011-05-26

Machine Gun 24 12.7mm NATO Nominated Weapon United States – General Dynamics M2 Heavy Barrel Machine Gun 25...Explosively-Clad Refractory Barrel Liners for Small Caliber Machine Guns , Dr. Douglas Taylor, TPL, Inc. 12299 - The HAMR Project, Mr. Xavier Gavage, FN Herstal... Barrel Liners for Small Caliber Machine Guns Dr. Douglas Taylor, TPL, Inc. 12330 - 40mm Low Velocity Air-Burst Munitions System Mr.

Evaluation of shuttle turbopump bearings

NASA Technical Reports Server (NTRS)

Dufrane, K. F.; Kannel, J. W.

1978-01-01

Because the high pressure turbopumps used on the space shuttle main engine (SSME) are high speed machines and rotor dynamics analysis of these units is very complicated, it was considered necessary to verify calculated turbomachinery shaft bearing loads by analysis of ball bearing load tracks. This report presents the methods used and the results of load track analysis on one set of bearings removed from a high pressure liquid oxygen turbopump which had been subjected to SSME static firing tests. This type of analysis was found useful in determining bearing operating conditions and for verifying rotor dynamics computer models.

29 CFR 1926.300 - General requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... apply to concrete vibrators, concrete breakers, powered tampers, jack hammers, rock drills, and similar... guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points...

29 CFR 1926.300 - General requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... apply to concrete vibrators, concrete breakers, powered tampers, jack hammers, rock drills, and similar... guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points...

29 CFR 1926.300 - General requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... apply to concrete vibrators, concrete breakers, powered tampers, jack hammers, rock drills, and similar... guarding. One or more methods of machine guarding shall be provided to protect the operator and other employees in the machine area from hazards such as those created by point of operation, ingoing nip points...

Minimizing soil impacts from forest operations

Treesearch

Emily A. Carter

2011-01-01

Several studies were conducted by Forest Service researchers and University and Industrial collaborators that investigated the potential for lessening soil surface disturbances and compaction in forest operations through modifications of machine components or harvest systems. Specific machine modifications included change in tire size, use of dual tire systems,...

Regenerative flywheel storage system, volume 2

NASA Astrophysics Data System (ADS)

1980-06-01

A vehicle propulsion system was simulated on a digital computer in order to determine the optimum system operating strategies and to establish a calculated range improvement over a nonregenerative, all electric vehicle. Fabrication of the inductor motor, the flywheel, the power conditioner, and the system control are described. Test results of the system operating over the SAE J227a Schedule D driving cycle are given and are compared to the calculated value. The flywheel energy storage system consists of a solid rotor, synchronous, inductor type, flywheel drive machine electrically coupled to a dc battery electric propulsion system through a load commutated inverter. The motor/alternator unit is coupled mechanically to a small steel flywheel which provides a portion of the vehicle's accelerating energy and regenerates the vehicle's braking energy.

Impact of Healthy Vending Machine Options in a Large Community Health Organization.

PubMed

Grivois-Shah, Ravi; Gonzalez, Juan R; Khandekar, Shashank P; Howerter, Amy L; O'Connor, Patrick A; Edwards, Barbara A

2017-01-01

To determine whether increasing the proportion of healthier options in vending machines decreases the amount of calories, fat, sugar, and sodium vended, while maintaining total sales revenue. This study evaluated the impact of altering nutritious options to vending machines throughout the Banner Health organization by comparing vended items' sales and nutrition information over 6 months compared to the same 6 months of the previous year. Twenty-three locations including corporate and patient-care centers. Changing vending machine composition toward more nutritious options. Comparisons of monthly aggregates of sales, units vended, calories, fat, sodium, and sugar vended by site. A pre-post analysis using paired t tests comparing 6 months before implementation to the equivalent 6 months postimplementation. Significant average monthly decreases were seen for calories (16.7%, P = .002), fat (27.4%, P ≤ .0001), sodium (25.9%, P ≤ .0001), and sugar (11.8%, P = .045) vended from 2014 to 2015. Changes in revenue and units vended did not change from 2014 to 2015 ( P = .58 and P = .45, respectively). Increasing the proportion of healthier options in vending machines from 20% to 80% significantly lowered the amount of calories, sodium, fat, and sugar vended, while not reducing units vended or having a negative financial impact.

49 CFR 214.507 - Required safety equipment for new on-track roadway maintenance machines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... glass, or other material with similar properties, if the machine is designed with a windshield. Each new... wipers or suitable alternatives that provide the machine operator an equivalent level of vision if...

Quench monitoring and control system and method of operating same

DOEpatents

Ryan, David Thomas; Laskaris, Evangelos Trifon; Huang, Xianrui

2006-05-30

A rotating machine comprising a superconductive coil and a temperature sensor operable to provide a signal representative of superconductive coil temperature. The rotating machine may comprise a control system communicatively coupled to the temperature sensor. The control system may be operable to reduce electric current in the superconductive coil when a signal representative of a defined superconducting coil temperature is received from the temperature sensor.

Incidence of MSDs and neck and back pain among logging machine operators in the southern U.S.

PubMed

Lynch, S M; Smidt, M F; Merrill, P D; Sesek, R F

2014-07-01

There are limited data about the incidence and prevalence of musculoskeletal disorders (MSDs) among loggers in the southern U.S. despite the risk factors associated with these occupations. Risk factors are both personal (age, body mass index, etc.) and job-related (awkward postures, repetitive hand and foot movements, vibration, etc.). A survey was conducted to estimate the incidence of self-reported pain and diagnosed MSDs and to study the relationship with known risk factors. Respondents were loggers attending training and continuing education classes. Respondents were asked to identify personal attributes, machine use, awkward postures, repetitive movements, and recent incidence of pain and medical diagnoses. All were male with an average age of 44 (range of 19-67) and an average body mass index of 31.3. Most were machine operators (97%) who have worked in the logging industry for an average of 22.9 years. Most machines identified were manufactured within the past ten years (average machine age 6.7 years). For machine operators, 10.5% (16) reported an MSD diagnosis, 74.3% (113) reported at least mild back pain, and 71.7% (109) reported at least mild neck pain over the past year. Further analysis attempted to identify an association between personal attributes, machine use, posture, and pain. Risk factors related to machine use may be biased since most survey respondents had considerable choice or control in working conditions, as they were firm owners and/or supervisors.

Automated fiber pigtailing machine

DOEpatents

Strand, Oliver T.; Lowry, Mark E.

1999-01-01

The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectonic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems.

Mobile Landing Platform with Core Capability Set (MLP w/CCS): Combined Initial Operational Test and Evaluation and Live Fire Test and Evaluation Report

DTIC Science & Technology

2015-07-01

annex.   iii Self-defense testing was limited to structural test firing from each machine gun mount and an ammunition resupply drill. Robust self...provided in the classified annex. Self-   8 defense testing was limited to structural test firing from each machine gun mount and a single...Caliber Machine Gun Mount Structural Test Fire November 2014 San Diego, Offshore Ship Weapons Range Operating Independently       9 Section Three

Reverse time migration: A seismic processing application on the connection machine

NASA Technical Reports Server (NTRS)

Fiebrich, Rolf-Dieter

1987-01-01

The implementation of a reverse time migration algorithm on the Connection Machine, a massively parallel computer is described. Essential architectural features of this machine as well as programming concepts are presented. The data structures and parallel operations for the implementation of the reverse time migration algorithm are described. The algorithm matches the Connection Machine architecture closely and executes almost at the peak performance of this machine.

International Business Machines (IBM) Corporation Interim Agreement EPA Case No. 08-0113-00

EPA Pesticide Factsheets

On March 27, 2008, the United States Environmental Protection Agency (EPA), suspended International Business Machines (IBM) from receiving Federal Contracts, approved subcontracts, assistance, loans and other benefits.

Machine Shop. Module 1: Machine Shop Orientation and Math. Instructor's Guide.

ERIC Educational Resources Information Center

Curtis, Donna; Nobles, Jack

This document consists of materials for a six-unit course on employment in the machine shop setting, safety, basic math skills, geometric figures and forms, math applications, and right triangles. The instructor's guide begins with a list of competencies covered in the module, descriptions of the materials included, an explanation of how to use…

Machine grading of lumber : practical concerns for lumber producers

Treesearch

William L. Galligan; Kent A. McDonald

2000-01-01

Machine lumber grading has been applied in commercial operations in North America since 1963, and research has shown that machine grading can improve the efficient use of wood. However, industry has been reluctant to apply research findings without clear evidence that the change from visual to machine grading will be a profitable one. For instance, mill managers need...

Machine Tool Operation, Course Description.

ERIC Educational Resources Information Center

Denny, Walter E.; Anderson, Floyd L.

Prepared by an instructor and curriculum specialists, this course of study was designed to meet the individual needs of the dropout and/or hard-core unemployed youth by providing them skill training, related information, and supportive services knowledge in machine tool operation. The achievement level of each student is determined at entry, and…

Machine Repairers and Operators. Reprinted from the Occupational Outlook Handbook, 1978-79 Edition.

ERIC Educational Resources Information Center

Bureau of Labor Statistics (DOL), Washington, DC.

Focusing on machine repairers and operators, this document is one in a series of forty-one reprints from the Occupational Outlook Handbook providing current information and employment projections for individual occupations and industries through 1985. The specific occupations covered in this document include appliance repairers,…

32 CFR 286.29 - Collection of fees and fee rates.

Code of Federal Regulations, 2011 CFR

2011-07-01

... human time may be also assessed as computer search. The terms “programmer/operator” shall not be limited to the traditional programmers or operators. Rather, the terms shall be interpreted in their broadest... support, operator, programmer, database administrator, or action officer). (ii) Machine time. Machine time...

5 CFR 532.279 - Special wage schedules for printing positions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Opaquer 4 Offset Press Helper 5 Bindery Machine Operator (Helper) 5 Film Assembler-Stripper (Single Flat-Single Color) 5 Platemaker (Single Color) 5 Film Assembler-Stripper (Partial and Composite Flats) 7... Cutter) 8 Bindery Machine Operator (Power Folder) 8 Film Assembler-Stripper (Multiple Flat-Multiple Color...

5 CFR 532.279 - Special wage schedules for printing positions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Opaquer 4 Offset Press Helper 5 Bindery Machine Operator (Helper) 5 Film Assembler-Stripper (Single Flat-Single Color) 5 Platemaker (Single Color) 5 Film Assembler-Stripper (Partial and Composite Flats) 7... Cutter) 8 Bindery Machine Operator (Power Folder) 8 Film Assembler-Stripper (Multiple Flat-Multiple Color...

Machine Operator Training Program and Curriculum.

ERIC Educational Resources Information Center

St. Cyr, David; And Others

This curriculum contains materials for use in duplicating the 11-week course for machine operators that was implemented at New Hampshire Vocational-Technical College in Nashua, New Hampshire. Addressed in the course, which is designed to prepare entry-level employees, are the following topics: basic math, blueprint reading, layout tools and…

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP.

PubMed

Deng, Li; Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency.

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP

PubMed Central

Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency. PMID:26448740

49 CFR 236.772 - Machine, interlocking.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 4 2011-10-01 2011-10-01 false Machine, interlocking. 236.772 Section 236.772 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Machine, interlocking. An assemblage of manually operated levers or other devices for the control of...

49 CFR 236.772 - Machine, interlocking.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Machine, interlocking. 236.772 Section 236.772 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Machine, interlocking. An assemblage of manually operated levers or other devices for the control of...

A mechanical Turing machine: blueprint for a biomolecular computer

PubMed Central

Shapiro, Ehud

2012-01-01

We describe a working mechanical device that embodies the theoretical computing machine of Alan Turing, and as such is a universal programmable computer. The device operates on three-dimensional building blocks by applying mechanical analogues of polymer elongation, cleavage and ligation, movement along a polymer, and control by molecular recognition unleashing allosteric conformational changes. Logically, the device is not more complicated than biomolecular machines of the living cell, and all its operations are part of the standard repertoire of these machines; hence, a biomolecular embodiment of the device is not infeasible. If implemented, such a biomolecular device may operate in vivo, interacting with its biochemical environment in a program-controlled manner. In particular, it may ‘compute’ synthetic biopolymers and release them into its environment in response to input from the environment, a capability that may have broad pharmaceutical and biological applications. PMID:22649583

Optimization-based manufacturing scheduling with multiple resources and setup requirements

NASA Astrophysics Data System (ADS)

Chen, Dong; Luh, Peter B.; Thakur, Lakshman S.; Moreno, Jack, Jr.

1998-10-01

The increasing demand for on-time delivery and low price forces manufacturer to seek effective schedules to improve coordination of multiple resources and to reduce product internal costs associated with labor, setup and inventory. This study describes the design and implementation of a scheduling system for J. M. Product Inc. whose manufacturing is characterized by the need to simultaneously consider machines and operators while an operator may attend several operations at the same time, and the presence of machines requiring significant setup times. The scheduling problem with these characteristics are typical for many manufacturers, very difficult to be handled, and have not been adequately addressed in the literature. In this study, both machine and operators are modeled as resources with finite capacities to obtain efficient coordination between them, and an operator's time can be shared by several operations at the same time to make full use of the operator. Setups are explicitly modeled following our previous work, with additional penalties on excessive setups to reduce setup costs and avoid possible scraps. An integer formulation with a separable structure is developed to maximize on-time delivery of products, low inventory and small number of setups. Within the Lagrangian relaxation framework, the problem is decomposed into individual subproblems that are effectively solved by using dynamic programming with additional penalties embedded in state transitions. Heuristics is then developed to obtain a feasible schedule following on our previous work with new mechanism to satisfy operator capacity constraints. The method has been implemented using the object-oriented programming language C++ with a user-friendly interface, and numerical testing shows that the method generates high quality schedules in a timely fashion. Through simultaneous consideration of machines and operators, machines and operators are well coordinated to facilitate the smooth flow of parts through the system. The explicit modeling of setups and the associated penalties let parts with same setup requirements clustered together to avoid excessive setups.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Menczer, L.F.

A study of 41 x-ray machines in 31 private dental offices in the Greater Hartford area showed that every x-ray unit permitted gonadal radiation exposure, ranging from 8 to 88 Mr. With few exceptions, the timing devices on all units were inaccurate by as much as 1/2 sec. About 20% of the units needed some mechanical repair, and 7 units demonstrated excessive lealcage radiation. In 50% of the dental offices, x-ray film was purchased on a cost basis rather than on a quality basis. The average length of exposure per film ranged from 3/4 to 4 sec; the usual exposuremore » was from 12/4 to 21/4 sec. No x-ray unit was on an independent electrical supply. Timer cords were usually no more than 5 ft long and did not permit the operator to get into a more protected position when exposing dental roentgenograms. In several instances the x-ray unit was close to business offices or to treatment rooms. The attitude of the average dentist in the study toward the potential hazards of x-ray radiation to his office personnel and patients was poor or showed lack of concern. Recommendations for reduction of gonadal radiation exposure are given. (TCO)« less

Maximum-Likelihood Estimation With a Contracting-Grid Search Algorithm

PubMed Central

Hesterman, Jacob Y.; Caucci, Luca; Kupinski, Matthew A.; Barrett, Harrison H.; Furenlid, Lars R.

2010-01-01

A fast search algorithm capable of operating in multi-dimensional spaces is introduced. As a sample application, we demonstrate its utility in the 2D and 3D maximum-likelihood position-estimation problem that arises in the processing of PMT signals to derive interaction locations in compact gamma cameras. We demonstrate that the algorithm can be parallelized in pipelines, and thereby efficiently implemented in specialized hardware, such as field-programmable gate arrays (FPGAs). A 2D implementation of the algorithm is achieved in Cell/BE processors, resulting in processing speeds above one million events per second, which is a 20× increase in speed over a conventional desktop machine. Graphics processing units (GPUs) are used for a 3D application of the algorithm, resulting in processing speeds of nearly 250,000 events per second which is a 250× increase in speed over a conventional desktop machine. These implementations indicate the viability of the algorithm for use in real-time imaging applications. PMID:20824155

Apparatus to collect, classify, concentrate, and characterize gas-borne particles

DOEpatents

Rader, Daniel J.; Torczynski, John R.; Wally, Karl; Brockmann, John E.

2002-01-01

An aerosol lab-on-a-chip (ALOC) integrates one or more of a variety of aerosol collection, classification, concentration (enrichment), and characterization processes onto a single substrate or layered stack of such substrates. By taking advantage of modern micro-machining capabilities, an entire suite of discrete laboratory aerosol handling and characterization techniques can be combined in a single portable device that can provide a wealth of data on the aerosol being sampled. The ALOC offers parallel characterization techniques and close proximity of the various characterization modules helps ensure that the same aerosol is available to all devices (dramatically reducing sampling and transport errors). Micro-machine fabrication of the ALOC significantly reduces unit costs relative to existing technology, and enables the fabrication of small, portable ALOC devices, as well as the potential for rugged design to allow operation in harsh environments. Miniaturization also offers the potential of working with smaller particle sizes and lower pressure drops (leading to reduction of power consumption).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Levin, J.

A case is reported of a 39-yr-old dentist who realized that his dental x- ray machine had been on for about 90 min. During this time he was near the machine constantly, with his back usually toward the source of radiation. The estimated dose to the back of his head and upper torso was 180 r. The dentist saffered some anxiety, but no acute symptoms of radiation sickness. Physical examination gave negative results. There was no evidence of acute radiation damage. Study of temporal scalp hair revealed an estimated maximum dose received by the hair follicles of approximates 50 tomore » 75 r. The direct technical cause of the accident was a loose washer in the timer mechanism, making contact and completing the switching circuit, thereby causing the unit to go on. It is suggested that dentists and their assistants should wear radiation exposure badges at all times. In addition, equipment shouid be systcmatically and regularly checked so that maximum operating efficiency can be combined with minimum exposure. (P.C.H.)« less

Large space structures fabrication experiment. [on-orbit fabrication of graphite/thermoplastic beams

NASA Technical Reports Server (NTRS)

1978-01-01

The fabrication machine used for the rolltrusion and on-orbit forming of graphite thermoplastic (CTP) strip material into structural sections is described. The basic process was analytically developed parallel with, and integrated into the conceptual design of, a flight experiment machine for producing a continuous triangular cross section truss. The machine and its associated ancillary equipment are mounted on a Space Lab pallet. Power, thermal control, and instrumentation connections are made during ground installation. Observation, monitoring, caution and warning, and control panels and displays are installed at the payload specialist station in the orbiter. The machine is primed before flight by initiation of beam forming, to include attachment of the first set of cross members and anchoring of the diagonal cords. Control of the experiment will be from the orbiter mission specialist station. Normal operation is by automatic processing control software. Machine operating data are displayed and recorded on the ground. Data is processed and formatted to show progress of the major experiment parameters including stable operation, physical symmetry, joint integrity, and structural properties.

Start-up and control method and apparatus for resonant free piston Stirling engine

DOEpatents

Walsh, Michael M.

1984-01-01

A resonant free-piston Stirling engine having a new and improved start-up and control method and system. A displacer linear electrodynamic machine is provided having an armature secured to and movable with the displacer and having a stator supported by the Stirling engine housing in juxtaposition to the armature. A control excitation circuit is provided for electrically exciting the displacer linear electrodynamic machine with electrical excitation signals having substantially the same frequency as the desired frequency of operation of the Stirling engine. The excitation control circuit is designed so that it selectively and controllably causes the displacer electrodynamic machine to function either as a generator load to extract power from the displacer or the control circuit selectively can be operated to cause the displacer electrodynamic machine to operate as an electric drive motor to apply additional input power to the displacer in addition to the thermodynamic power feedback to the displacer whereby the displacer linear electrodynamic machine also is used in the electric drive motor mode as a means for initially starting the resonant free-piston Stirling engine.

Utility operational experience on the NASA/DOE MOD-0A 200-kW wind turbine

NASA Technical Reports Server (NTRS)

Glasgow, J. C.; Robbins, W. H.

1979-01-01

The Mod-0A 200 wind turbine was designed and fabricated as part of the Federal Wind Energy Program. Early wind turbine operation and performance data were obtained while gaining initial experience in the operation of large, horizontal axis wind turbines in typical utility environments. The Mod-0A wind turbine was turned over to the Town of Clayton Light and Water Plant, Clayton, NM, for utility operation and on December 31, 1978, the machine had completed ten months of utility operation. The machine is described and the recent operational experience at Clayton, NMis documented.

The Surge Capacity for People in Emergencies (SCOPE) study in Australasian hospitals.

PubMed

Traub, Matthias; Bradt, David A; Joseph, Anthony P

2007-04-16

To measure physical assets in Australasian hospitals required for the management of mass casualties as a result of terrorism or natural disasters. A cross-sectional survey of Australian and New Zealand hospitals. All emergency department directors of Australasian College for Emergency Medicine (ACEM)-accredited hospitals, as well as private and non-ACEM accredited emergency departments staffed by ACEM Fellows in metropolitan Sydney. Numbers of operating theatres, intensive care unit (ICU) beds and x-ray machines; state of preparedness using benchmarks defined by the Centers for Disease Control and Prevention in the United States. We found that 61%-82% of critically injured patients would not have immediate access to operative care, 34%-70% would have delayed access to an ICU bed, and 42% of the less critically injured would have delayed access to x-ray facilities. Our study demonstrates that physical assets in Australasian public hospitals do not meet US hospital preparedness benchmarks for mass casualty incidents. We recommend national agreement on disaster preparedness benchmarks and periodic publication of hospital performance indicators to enhance disaster preparedness.

Prediction and early detection of delirium in the intensive care unit by using heart rate variability and machine learning.

PubMed

Oh, Jooyoung; Cho, Dongrae; Park, Jaesub; Na, Se Hee; Kim, Jongin; Heo, Jaeseok; Shin, Cheung Soo; Kim, Jae-Jin; Park, Jin Young; Lee, Boreom

2018-03-27

Delirium is an important syndrome found in patients in the intensive care unit (ICU), however, it is usually under-recognized during treatment. This study was performed to investigate whether delirious patients can be successfully distinguished from non-delirious patients by using heart rate variability (HRV) and machine learning. Electrocardiography data of 140 patients was acquired during daily ICU care, and HRV data were analyzed. Delirium, including its type, severity, and etiologies, was evaluated daily by trained psychiatrists. HRV data and various machine learning algorithms including linear support vector machine (SVM), SVM with radial basis function (RBF) kernels, linear extreme learning machine (ELM), ELM with RBF kernels, linear discriminant analysis, and quadratic discriminant analysis were utilized to distinguish delirium patients from non-delirium patients. HRV data of 4797 ECGs were included, and 39 patients had delirium at least once during their ICU stay. The maximum classification accuracy was acquired using SVM with RBF kernels. Our prediction method based on HRV with machine learning was comparable to previous delirium prediction models using massive amounts of clinical information. Our results show that autonomic alterations could be a significant feature of patients with delirium in the ICU, suggesting the potential for the automatic prediction and early detection of delirium based on HRV with machine learning.

Executable Architecture of Net Enabled Operations: State Machine of Federated Nodes

DTIC Science & Technology

2009-11-01

verbal descriptions from operators) of the current Command and Control (C2) practices into model form. In theory these should be Standard Operating...faudra une grande quantité de données pour faire en sorte que le modèle reflète les processus véritables, les auteurs recommandent que la machine à...descriptions from operators) of the current C2 practices into model form. In theory these should be SOPs that execute as a thread from start to finish. The

Summary of the Optics, IR, Injection, Operations, Reliability and Instrumentation Working Group

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wienands, U.; /SLAC; Funakoshi, Y.

2012-04-20

The facilities reported on are all in a fairly mature state of operation, as evidenced by the very detailed studies and correction schemes that all groups are working on. First- and higher-order aberrations are diagnosed and planned to be corrected. Very detailed beam measurements are done to get a global picture of the beam dynamics. More than other facilities the high-luminosity colliders are struggling with experimental background issues, mitigation of which is a permanent challenge. The working group dealt with a very wide rage of practical issues which limit performance of the machines and compared their techniques of operations andmore » their performance. We anticipate this to be a first attempt. In a future workshop in this series, we propose to attempt more fundamental comparisons of each machine, including design parameters. For example, DAPHNE and KEKB employ a finite crossing angle. The minimum value of {beta}*{sub y} attainable at KEKB seems to relate to this scheme. Effectiveness of compensation solenoids and turn-by-turn BPMs etc. should be examined in more detail. In the near future, CESR-C and VEPP-2000 will start their operation. We expect to hear important new experiences from these machines; in particular VEPP-2000 will be the first machine to have adopted round beams. At SLAC and KEK, next generation B Factories are being considered. It will be worthwhile to discuss the design issues of these machines based on the experiences of the existing factory machines.« less

The Efficacy of Machine Learning Programs for Navy Manpower Analysis

DTIC Science & Technology

1993-03-01

This thesis investigated the efficacy of two machine learning programs for Navy manpower analysis. Two machine learning programs, AIM and IXL, were...to generate models from the two commercial machine learning programs. Using a held out sub-set of the data the capabilities of the three models were...partial effects. The author recommended further investigation of AIM’s capabilities, and testing in an operational environment.... Machine learning , AIM, IXL.

Pressure-Letdown Machine for a Coal Reactor

NASA Technical Reports Server (NTRS)

Perkins, G. S.; Mabe, W. B.

1986-01-01

Pumps operating in reverse generate power. Conceptual pressure-letdown machine for coal-liquefaction system extracts energy from expansion of product fluid. Mud pumps, originally intended for use in oil drilling, operated in reverse so their motors act as generators. Several pumps operated in alternating phase to obtain multiple stages of letdown from inlet pressure to outlet pressure. About 75 percent of work generates inlet pressure recoverable as electrical energy.

Some single-piston closed-cycle machines and Peter Tailer's thermal lag engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

West, C.D.

1993-01-01

Peter Tailer has devised, built, and operated a beautifully simple engine with a closed working gas cycle, external heating, and only a single piston. The aim of this paper is to cast some light on the possible modes of operation for his machine. The methods develops to analyze certain aspects of Stirling cycle engines, and especially the thermodynamic losses incurred in systems that are neither perfectly isothermal nor perfectly adiabatic, can be applied to Tailer's system. The results identify two idealized cycles fr such machines; relate those cycles to a single piston, ported cylinder machine proposed earlier; and offer amore » possible explanation for the success of the thermal lag engine.« less

Methods, systems and apparatus for adjusting duty cycle of pulse width modulated (PWM) waveforms

DOEpatents

Gallegos-Lopez, Gabriel; Kinoshita, Michael H; Ransom, Ray M; Perisic, Milun

2013-05-21

Embodiments of the present invention relate to methods, systems and apparatus for controlling operation of a multi-phase machine in a vector controlled motor drive system when the multi-phase machine operates in an overmodulation region. The disclosed embodiments provide a mechanism for adjusting a duty cycle of PWM waveforms so that the correct phase voltage command signals are applied at the angle transitions. This can reduce variations/errors in the phase voltage command signals applied to the multi-phase machine so that phase current may be properly regulated thus reducing current/torque oscillation, which can in turn improve machine efficiency and performance, as well as utilization of the DC voltage source.

Machine Learning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chikkagoudar, Satish; Chatterjee, Samrat; Thomas, Dennis G.

The absence of a robust and unified theory of cyber dynamics presents challenges and opportunities for using machine learning based data-driven approaches to further the understanding of the behavior of such complex systems. Analysts can also use machine learning approaches to gain operational insights. In order to be operationally beneficial, cybersecurity machine learning based models need to have the ability to: (1) represent a real-world system, (2) infer system properties, and (3) learn and adapt based on expert knowledge and observations. Probabilistic models and Probabilistic graphical models provide these necessary properties and are further explored in this chapter. Bayesian Networksmore » and Hidden Markov Models are introduced as an example of a widely used data driven classification/modeling strategy.« less

Safety illusion and error trap in a collectively-operated machine accident.

PubMed

de Almeida, Ildeberto Muniz; Nobre, Hildeberto; do Amaral Dias, Maria Dionísia; Vilela, Rodolfo Andrade Gouveia

2012-01-01

Workplace accidents involving machines are relevant for their magnitude and their impacts on worker health. Despite consolidated critical statements, explanation centered on errors of operators remains predominant with industry professionals, hampering preventive measures and the improvement of production-system reliability. Several initiatives were adopted by enforcement agencies in partnership with universities to stimulate production and diffusion of analysis methodologies with a systemic approach. Starting from one accident case that occurred with a worker who operated a brake-clutch type mechanical press, the article explores cognitive aspects and the existence of traps in the operation of this machine. It deals with a large-sized press that, despite being endowed with a light curtain in areas of access to the pressing zone, did not meet legal requirements. The safety devices gave rise to an illusion of safety, permitting activation of the machine when a worker was still found within the operational zone. Preventive interventions must stimulate the tailoring of systems to the characteristics of workers, minimizing the creation of traps and encouraging safety policies and practices that replace judgments of behaviors that participate in accidents by analyses of reasons that lead workers to act in that manner.

Expected load spectra of prototype Francis turbines in low-load operation using numerical simulations and site measurements

NASA Astrophysics Data System (ADS)

Eichhorn, M.; Taruffi, A.; Bauer, C.

2017-04-01

The operators of hydropower plants are forced to extend the existing operating ranges of their hydraulic machines to remain competitive on the energy market due to the rising amount of wind and solar power. Faster response times and a higher flexibility towards part- and low-load conditions enable a better electric grid control and assure therefore an economic operation of the power plant. The occurring disadvantage is a higher dynamic excitation of affected machine components, especially Francis turbine runners, due to pressure pulsations induced by unsteady flow phenomena (e.g. draft tube vortex ropes). Therefore, fatigue analysis becomes more important even in the design phase of the hydraulic machines to evaluate the static and dynamic load in different operating conditions and to reduce maintenance costs. An approach including a one-way coupled fluid-structure interaction has been already developed using unsteady CFD simulations and transient FEM computations. This is now applied on two Francis turbines with different specific speeds and power ranges, to obtain the load spectra of both machines. The results are compared to strain gauge measurements on the according Francis turbines to validate the overall procedure.

Integration of Machining and Inspection in Aerospace Manufacturing

NASA Astrophysics Data System (ADS)

Simpson, Bart; Dicken, Peter J.

2011-12-01

The main challenge for aerospace manufacturers today is to develop the ability to produce high-quality products on a consistent basis as quickly as possible and at the lowest-possible cost. At the same time, rising material prices are making the cost of scrap higher than ever so making it more important to minimise waste. Proper inspection and quality control methods are no longer a luxury; they are an essential part of every manufacturing operation that wants to grow and be successful. However, simply bolting on some quality control procedures to the existing manufacturing processes is not enough. Inspection must be fully-integrated with manufacturing for the investment to really produce significant improvements. The traditional relationship between manufacturing and inspection is that machining is completed first on the company's machine tools and the components are then transferred to dedicated inspection equipment to be approved or rejected. However, as machining techniques become more sophisticated, and as components become larger and more complex, there are a growing number of cases where closer integration is required to give the highest productivity and the biggest reductions in wastage. Instead of a simple linear progression from CAD to CAM to machining to inspection, a more complicated series of steps is needed, with extra data needed to fill any gaps in the information available at the various stages. These new processes can be grouped under the heading of "adaptive machining". The programming of most machining operations is based around knowing three things: the position of the workpiece on the machine, the starting shape of the material to be machined, and the final shape that needs to be achieved at the end of the operation. Adaptive machining techniques allow successful machining when at least one of those elements is unknown, by using in-process measurement to close the information gaps in the process chain. It also allows any errors to be spotted earlier in the manufacturing process, so helping the problems to be resolved more quickly and at lower cost.

Design of a Closed-Loop, Bidirectional Brain Machine Interface System With Energy Efficient Neural Feature Extraction and PID Control.

PubMed

Liu, Xilin; Zhang, Milin; Richardson, Andrew G; Lucas, Timothy H; Van der Spiegel, Jan

2017-08-01

This paper presents a bidirectional brain machine interface (BMI) microsystem designed for closed-loop neuroscience research, especially experiments in freely behaving animals. The system-on-chip (SoC) consists of 16-channel neural recording front-ends, neural feature extraction units, 16-channel programmable neural stimulator back-ends, in-channel programmable closed-loop controllers, global analog-digital converters (ADC), and peripheral circuits. The proposed neural feature extraction units includes 1) an ultra low-power neural energy extraction unit enabling a 64-step natural logarithmic domain frequency tuning, and 2) a current-mode action potential (AP) detection unit with time-amplitude window discriminator. A programmable proportional-integral-derivative (PID) controller has been integrated in each channel enabling a various of closed-loop operations. The implemented ADCs include a 10-bit voltage-mode successive approximation register (SAR) ADC for the digitization of the neural feature outputs and/or local field potential (LFP) outputs, and an 8-bit current-mode SAR ADC for the digitization of the action potential outputs. The multi-mode stimulator can be programmed to perform monopolar or bipolar, symmetrical or asymmetrical charge balanced stimulation with a maximum current of 4 mA in an arbitrary channel configuration. The chip has been fabricated in 0.18 μ m CMOS technology, occupying a silicon area of 3.7 mm 2 . The chip dissipates 56 μW/ch on average. General purpose low-power microcontroller with Bluetooth module are integrated in the system to provide wireless link and SoC configuration. Methods, circuit techniques and system topology proposed in this work can be used in a wide range of relevant neurophysiology research, especially closed-loop BMI experiments.

Biomimetic molecular design tools that learn, evolve, and adapt.

PubMed

Winkler, David A

2017-01-01

A dominant hallmark of living systems is their ability to adapt to changes in the environment by learning and evolving. Nature does this so superbly that intensive research efforts are now attempting to mimic biological processes. Initially this biomimicry involved developing synthetic methods to generate complex bioactive natural products. Recent work is attempting to understand how molecular machines operate so their principles can be copied, and learning how to employ biomimetic evolution and learning methods to solve complex problems in science, medicine and engineering. Automation, robotics, artificial intelligence, and evolutionary algorithms are now converging to generate what might broadly be called in silico-based adaptive evolution of materials. These methods are being applied to organic chemistry to systematize reactions, create synthesis robots to carry out unit operations, and to devise closed loop flow self-optimizing chemical synthesis systems. Most scientific innovations and technologies pass through the well-known "S curve", with slow beginning, an almost exponential growth in capability, and a stable applications period. Adaptive, evolving, machine learning-based molecular design and optimization methods are approaching the period of very rapid growth and their impact is already being described as potentially disruptive. This paper describes new developments in biomimetic adaptive, evolving, learning computational molecular design methods and their potential impacts in chemistry, engineering, and medicine.

Biomimetic molecular design tools that learn, evolve, and adapt

PubMed Central

2017-01-01

A dominant hallmark of living systems is their ability to adapt to changes in the environment by learning and evolving. Nature does this so superbly that intensive research efforts are now attempting to mimic biological processes. Initially this biomimicry involved developing synthetic methods to generate complex bioactive natural products. Recent work is attempting to understand how molecular machines operate so their principles can be copied, and learning how to employ biomimetic evolution and learning methods to solve complex problems in science, medicine and engineering. Automation, robotics, artificial intelligence, and evolutionary algorithms are now converging to generate what might broadly be called in silico-based adaptive evolution of materials. These methods are being applied to organic chemistry to systematize reactions, create synthesis robots to carry out unit operations, and to devise closed loop flow self-optimizing chemical synthesis systems. Most scientific innovations and technologies pass through the well-known “S curve”, with slow beginning, an almost exponential growth in capability, and a stable applications period. Adaptive, evolving, machine learning-based molecular design and optimization methods are approaching the period of very rapid growth and their impact is already being described as potentially disruptive. This paper describes new developments in biomimetic adaptive, evolving, learning computational molecular design methods and their potential impacts in chemistry, engineering, and medicine. PMID:28694872

49 CFR 214.341 - Roadway maintenance machines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY Roadway Worker Protection § 214.341 Roadway maintenance machines. (a) Each employer shall include in its on-track safety program specific provisions for the safety of roadway workers who operate or work near roadway maintenance machines. Those...

Limitations Of The Current State Space Modelling Approach In Multistage Machining Processes Due To Operation Variations

NASA Astrophysics Data System (ADS)

Abellán-Nebot, J. V.; Liu, J.; Romero, F.

2009-11-01

The State Space modelling approach has been recently proposed as an engineering-driven technique for part quality prediction in Multistage Machining Processes (MMP). Current State Space models incorporate fixture and datum variations in the multi-stage variation propagation, without explicitly considering common operation variations such as machine-tool thermal distortions, cutting-tool wear, cutting-tool deflections, etc. This paper shows the limitations of the current State Space model through an experimental case study where the effect of the spindle thermal expansion, cutting-tool flank wear and locator errors are introduced. The paper also discusses the extension of the current State Space model to include operation variations and its potential benefits.

A self-learning camera for the validation of highly variable and pseudorandom patterns

NASA Astrophysics Data System (ADS)

Kelley, Michael

2004-05-01

Reliable and productive manufacturing operations have depended on people to quickly detect and solve problems whenever they appear. Over the last 20 years, more and more manufacturing operations have embraced machine vision systems to increase productivity, reliability and cost-effectiveness, including reducing the number of human operators required. Although machine vision technology has long been capable of solving simple problems, it has still not been broadly implemented. The reason is that until now, no machine vision system has been designed to meet the unique demands of complicated pattern recognition. The ZiCAM family was specifically developed to be the first practical hardware to meet these needs. To be able to address non-traditional applications, the machine vision industry must include smart camera technology that meets its users" demands for lower costs, better performance and the ability to address applications of irregular lighting, patterns and color. The next-generation smart cameras will need to evolve as a fundamentally different kind of sensor, with new technology that behaves like a human but performs like a computer. Neural network based systems, coupled with self-taught, n-space, non-linear modeling, promises to be the enabler of the next generation of machine vision equipment. Image processing technology is now available that enables a system to match an operator"s subjectivity. A Zero-Instruction-Set-Computer (ZISC) powered smart camera allows high-speed fuzzy-logic processing, without the need for computer programming. This can address applications of validating highly variable and pseudo-random patterns. A hardware-based implementation of a neural network, Zero-Instruction-Set-Computer, enables a vision system to "think" and "inspect" like a human, with the speed and reliability of a machine.

[A field study on the work load and muscle fatigue at neck-shoulder in female sewing machine operators by using surface electromyography].

PubMed

Zhang, Fei-ruo; Wang, Sheng; He, Li-hua; Zhang, Ying; Wu, Shan-shan; Li, Jing-yun; Hu, Guang-yi; Ye, Kang-ping

2011-03-01

To study neck and shoulder work-related muscle fatigue of female sewing machine operators. 18 health female sewing machine operators without musculoskeletal disorders work in Beijing garment industry factory as volunteers in participate of this study. The maximal voluntary contraction (MVC) and 20% MVC of bilateral upper trapezium and cervical erectors spinae was tested before sewing operations, then the whole 20 time windows (1 time window = 10 min) sewing machine operations was monitored and the surface electromyography (sEMG) signals simultaneously was recorded after monitoring the 20%MVC was tested. Use amplitude analysis method to reduction recorded EMG signals. During work, the median load for the left cervical erector spinae (LCES), right cervical erector spinae (RCES), left upper trapezium (LUT) and right upper trapezium (RUT) respectively was 6.78 ± 1.05, 6.94 ± 1.12, 5.68 ± 2.56 and 6.47 ± 3.22, work load of right is higher than the left; static load analysis indicated the value of RMS(20%MVC) before work was higher than that value after work, the increase of right CES and UT RMS(20%MVC) was more; the largest 20%MVE of bilateral CES occurred at 20th time window, and that of bilateral UT happened at 16th. The work load of female sewing machine operators is sustained "static" load, and work load of right neck-shoulder is higher than left, right neck-shoulder muscle is more fatigable and much serious once fatigued.

A Guide for Planning Facilities for Occupational Preparation Programs in the Machine Trades. Interim Report. Research 24.

ERIC Educational Resources Information Center

Larson, Milton E.

This guide is designed for use by any person or groups of persons responsible for planning occupational programs in the machine trades. Its major purpose is to elicit the necessary information for the writing of educational specifications for facilities to house needed vocational programs in machine tool operation, machine shop, and tool and die…

Reversible micromachining locator

DOEpatents

Salzer, Leander J.; Foreman, Larry R.

2002-01-01

A locator with a part support is used to hold a part onto the kinematic mount of a tooling machine so that the part can be held in or replaced in exactly the same position relative to the cutting tool for machining different surfaces of the part or for performing different machining operations on the same or different surfaces of the part. The locator has disposed therein a plurality of steel balls placed at equidistant positions around the planar surface of the locator and the kinematic mount has a plurality of magnets which alternate with grooves which accommodate the portions of the steel balls projecting from the locator. The part support holds the part to be machined securely in place in the locator. The locator can be easily detached from the kinematic mount, turned over, and replaced onto the same kinematic mount or another kinematic mount on another tooling machine without removing the part to be machined from the locator so that there is no need to touch or reposition the part within the locator, thereby assuring exact replication of the position of the part in relation to the cutting tool on the tooling machine for each machining operation on the part.

Notes on a storage manager for the Clouds kernel

NASA Technical Reports Server (NTRS)

Pitts, David V.; Spafford, Eugene H.

1986-01-01

The Clouds project is research directed towards producing a reliable distributed computing system. The initial goal is to produce a kernel which provides a reliable environment with which a distributed operating system can be built. The Clouds kernal consists of a set of replicated subkernels, each of which runs on a machine in the Clouds system. Each subkernel is responsible for the management of resources on its machine; the subkernal components communicate to provide the cooperation necessary to meld the various machines into one kernel. The implementation of a kernel-level storage manager that supports reliability is documented. The storage manager is a part of each subkernel and maintains the secondary storage residing at each machine in the distributed system. In addition to providing the usual data transfer services, the storage manager ensures that data being stored survives machine and system crashes, and that the secondary storage of a failed machine is recovered (made consistent) automatically when the machine is restarted. Since the storage manager is part of the Clouds kernel, efficiency of operation is also a concern.

Diverse Effects, Complex Causes: Children Use Information about Machines' Functional Diversity to Infer Internal Complexity

ERIC Educational Resources Information Center

Ahl, Richard E.; Keil, Frank C.

2017-01-01

Four studies explored the abilities of 80 adults and 180 children (4-9 years), from predominantly middle-class families in the Northeastern United States, to use information about machines' observable functional capacities to infer their internal, "hidden" mechanistic complexity. Children as young as 4 and 5 years old used machines'…

Does Machine-Readable Documentation on Online Hosts and CD-ROMs Have a Role or Future?

ERIC Educational Resources Information Center

Harris, Stephen; Oppenheim, Charles

1996-01-01

Reports results of a United Kingdom-based mail survey of database users, CD-ROM producers, and hosts to assess trends and views concerning documentation in machine-readable form. Cost, convenience, and ease of use of print manuals are cited as reasons for the reluctance to switch to machine-readable documentation. Sample surveys are included.…

Telescoping magnetic ball bar test gage

DOEpatents

Bryan, J.B.

1982-03-15

A telescoping magnetic ball bar test gage for determining the accuracy of machine tools, including robots, and those measuring machines having non-disengagable servo drives which cannot be clutched out. Two gage balls are held and separated from one another by a telescoping fixture which allows them relative radial motional freedom but not relative lateral motional freedom. The telescoping fixture comprises a parallel reed flexure unit and a rigid member. One gage ball is secured by a magnetic socket knuckle assembly which fixes its center with respect to the machine being tested. The other gage ball is secured by another magnetic socket knuckle assembly which is engaged or held by the machine in such manner that the center of that ball is directed to execute a prescribed trajectory, all points of which are equidistant from the center of the fixed gage ball. As the moving ball executes its trajectory, changes in the radial distance between the centers of the two balls caused by inaccuracies in the machine are determined or measured by a linear variable differential transformer (LVDT) assembly actuated by the parallel reed flexure unit. Measurements can be quickly and easily taken for multiple trajectories about several different fixed ball locations, thereby determining the accuracy of the machine.

Nanometric edge profile measurement of cutting tools on a diamond turning machine

NASA Astrophysics Data System (ADS)

Asai, Takemi; Arai, Yoshikazu; Cui, Yuguo; Gao, Wei

2008-10-01

Single crystal diamond tools are used for fabrication of precision parts [1-5]. Although there are many types of tools that are supplied, the tools with round nose are popular for machining very smooth surfaces. Tools with small nose radii, small wedge angles and included angles are also being utilized for fabrication of micro structured surfaces such as microlens arrays [6], diffractive optical elements and so on. In ultra precision machining, tools are very important as a part of the machining equipment. The roughness or profile of machined surface may become out of desired tolerance. It is thus necessary to know the state of the tool edge accurately. To meet these requirements, an atomic force microscope (AFM) for measuring the 3D edge profiles of tools having nanometer-scale cutting edge radii with high resolution has been developed [7-8]. Although the AFM probe unit is combined with an optical sensor for aligning the measurement probe with the tools edge top to be measured in short time in this system, this time only the AFM probe unit was used. During the measurement time, that was attached onto the ultra precision turning machine to confirm the possibility of profile measurement system.