Characterization of major lithologic units underlying the lower American River using water-borne continuous resistivity profiling, Sacramento, California, June 2008

USGS Publications Warehouse

Ball, Lyndsay B.; Teeple, Andrew

2013-01-01

The levee system of the lower American River in Sacramento, California, is situated above a mixed lithology of alluvial deposits that range from clay to gravel. In addition, sand deposits related to hydraulic mining activities underlie the floodplain and are preferentially prone to scour during high-flow events. In contrast, sections of the American River channel have been observed to be scour resistant. In this study, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, explores the resistivity structure of the American River channel to characterize the extent and thickness of lithologic units that may impact the scour potential of the area. Likely lithologic structures are interpreted, but these interpretations are non-unique and cannot be directly related to scour potential. Additional geotechnical data would provide insightful data on the scour potential of certain lithologic units. Additional interpretation of the resistivity data with respect to these results may improve interpretations of lithology and scour potential throughout the American River channel and floodplain. Resistivity data were collected in three profiles along the American River using a water-borne continuous resistivity profiling technique. After processing and modeling these data, inverted resistivity profiles were used to make interpretations about the extent and thickness of possible lithologic units. In general, an intermittent high-resistivity layer likely indicative of sand or gravel deposits extends to a depth of around 30 feet (9 meters) and is underlain by a consistent low-resistivity layer that likely indicates a high-clay content unit that extends below the depth of investigation (60 feet or 18 meters). Immediately upstream of the Watt Avenue Bridge, the high-resistivity layer is absent, and the low-resistivity layer extends to the surface where a scour-resistant layer has been previously observed in the river bed.

Geology of the surficial aquifer system, Dade County, Florida; lithologic logs

USGS Publications Warehouse

Causaras, C.R.

1986-01-01

The geologic framework of the surficial aquifer system in Dade County, Florida, was investigated as part of a longterm study by the USGS in cooperation with the South Florida Water Management District, to describe the geology, hydrologic characteristics, and groundwater quality of the surficial aquifer system. Thirty-three test wells were drilled completely through the surficial aquifer system and into the underlying, relatively impermeable units of the Tamiami and Hawthorn Formations. Detailed lithologic logs were made from microscopic examination of rock cuttings and cores obtained from these wells. The logs were used to prepare geologic sections that show the lithologic variations, thickness of the lithologic units, and different geologic formations that comprise the aquifers system. (Author 's abstract)

Landsat TM data processing for lithological discrimination in the Caraculo area (Namibe Province, SW Angola)

NASA Astrophysics Data System (ADS)

Alberti, A.; Alessandro, V.; Pieruccini, U.; Pranzini, E.

1993-10-01

Landsat TM data were used for lithological discrimination and mapping in the little-known, semiarid 900 km 2 area around Caraculo station and the middle course of the Rio Giraul (Namibe Province, SW Angola) following two main procedures. The first of these was based on visual evaluation of three-band composites, band-ratio composites and Principal Component Analysis. The second method relied on the extraction of spectral signatures, and their use to obtain automatic classifications. Satisfactory results were reached with the first procedure, thus allowing - with limited support of ground information — the draft of a lithological map, while the second method was not systematically efficient, even for confirmation of data acquired with the first procedure. Image interpretation suggests that an extensive but hithertoun differentiated metasedimentary complex consisting of a heterogeneous supracrustal sequence should be subdivided into at least two units. Field observations proved that one of these is marked by a notable frequency of marbles and the other is characterized by a widespread occurrence of amphibolitic bodies. Moreover, a belt of undetermined (thermally metamorphosed ?) metamorphic rocks is interposed between them. The distinction of so far unidentified units, though restricted to interpretation of processed Landsat TM data, has significant geological implications also in the regional context and will be helpful in guiding future work with conventional geological methods.

Overview of the magnetic signatures of the Palaeoproterozoic Rustenburg Layered Suite, Bushveld Complex, South Africa

USGS Publications Warehouse

Cole, Janine; Finn, Carol A.; Webb, Susan J.

2013-01-01

Aeromagnetic data clearly delineate the mafic rocks of the economically significant Bushveld Igneous Complex. This is mainly due to the abundance of magnetite in the Upper Zone of the Rustenburg Layered Suite of the Bushveld, but strongly remanently magnetised rocks in the Main Zone also contribute significantly in places. In addition to delineating the extent of the magnetic rocks in the complex, the magnetic anomalies also provide information about the dip and depth of these units. The presence of varying degrees of remanent magnetisation in most of the magnetic lithologies of the Rustenburg Layered Suite complicates the interpretation of the data. The combination of available regional and high resolution airborne magnetic data with published palaeomagnetic data reveals characteristic magnetic signatures associated with the different magnetic lithologies in the Rustenburg Layered Suite. As expected, the ferrogabbros of the Upper Zone cause the highest amplitude magnetic anomalies, but in places subtle features within the Main Zone can also be detected. A marker with strong remanent magnetisation located in the Main Zone close to the contact with the Upper Zone is responsible for very high amplitude negative anomalies in the southern parts of both the eastern and western lobes of the Bushveld Complex. Prominent anomalies are not necessarily related to a specific lithology, but can result from the interaction between anomalies caused by differently magnetised bodies.The magnetic data provided substantial information at different levels of detail, ranging from contacts between zones, and layering within zones, to magnetite pipes dykes and faults that can have an impact on mine planning. Finally, simple modelling of the magnetic data supports the concept of continuous mafic rocks between the western and eastern lobes.

Lithologic and ground-water data for monitoring sites in the Mojave River and Warren Valley basins, San Bernardino County, California, 1992-1998

USGS Publications Warehouse

Huff, Julia A.; Clark, Dennis A.; Martin, Peter

2002-01-01

Lithologic and ground-water data were collected at 85 monitoring sites constructed in the Mojave Water Agency Management area in San Bernardino County, California, as part of a series of cooperative studies between the U.S. Geological Survey and the Mojave Water Agency. The data are being used to evaluate and address water-supply and water-quality issues. This report presents a compilation of the data collected at these sites from 1992 through 1998, including location and design of the monitoring sites, lithologic data, geophysical logs, ground-water-level measurements, and water-quality analyses.One to five small (generally 2-inch) diameter wells were installed at each of the 85 monitoring sites to collect depth-dependent hydrologic data. Lithologic logs were compiled from descriptions of drill cuttings collected at each site and from observations recorded during the drilling of the borehole. Generalized stratigraphic columns were compiled by grouping similar lithologic units. Geophysical logs provide information on the character of the lithologic units and on the presence of ground water and the chemical characteristics of that water. Water-level and water-quality data were collected periodically from the sites during 1992 through 1998.

How steep are the Alps?

NASA Astrophysics Data System (ADS)

Robl, Jörg; Prasicek, Günther; Stüwe, Kurt; Hergarten, Stefan

2014-05-01

The topography of the European Alps reflects continental collision, crustal thickening and buoyancy driven surface uplift, overprinted by erosional processes. Topographic gradients generally steepen from the valley floors up to about 1500 m - 2000 m followed by an unexpected decrease in slope up to about 2900 m and a further increase to the highest summits of the range. Several studies have interpreted this pattern and the accompanied maximum in the hypsometric curve in terms of either the critical slope stability angle, the prematurity of the Alps caused by recent tectonic uplift, or the effect of the glacial "buzz saw" related to the Pleistocene glaciation cycles. There is consensus that the lithological inventory represents a first order parameter for the steepness of fluvial channels and the angle of hillslopes in steady state and that the response time of a transient landscape is controlled by lithology. In this study we systematically explore the slope-elevation distributions for several hundred continuous domains of the major structural units of the Alps. For this, we apply a novel numerical code to determine the predominant cause for the observed peculiar topography. We compare adjacent alpine domains with contrasting lithology to explore lithological effects on the limiting slope stability angle. We analyze domains with different lithology in the non-glaciated parts of the orogen to highlight the state of maturity related to a recent uplift event. We evaluate the glacial effects on the landscape by the comparison of areas belonging to the same structural units but affected by a variable amount of glacial imprint. The results show that lithology has a major impact on the morphometric characteristics of the European Alps. Adjacent but different structural units show a significant variability in their slope-elevation distributions although they have experienced the same uplift history and the same amount of glacial imprint. This suggests that the response time and process rates in transient landscapes are predominantly governed by the lithological inventory. Areas belonging to the same structural unit show similar characteristics in the slope-elevation distribution independent from their spatial position within the orogen (e.g. external massifs). These similarities are probably caused by the vertical position of the Pleistocene equilibrium line altitude - an observation well in line with the glacial "buzz saw" hypothesis. However, several non-glaciated regions at the eastern and south-western border of the Alps show a slope-elevation relation similar to formerly glaciated domains. However, in contrast to the glaciated realm, the inflection point in the slope-elevation distribution is located at various elevation levels and is consistent with a reported recent pulse of uplift with spatial and/or temporal variations in uplift rate and initiation. Therefore, we interpret the slope-elevation distribution of the European Alps to be mainly caused by glacial erosion. The morphological record of a recent uplift event in the Alps has probably been overprinted by Pleistocene glaciations and may therefore only be detectable in non-glaciated regions of the peripheral parts of the Alps and in subsurface structures.

Texture-Based Automated Lithological Classification Using Aeromagenetic Anomaly Images

USGS Publications Warehouse

Shankar, Vivek

2009-01-01

This report consists of a thesis submitted to the faculty of the Department of Electrical and Computer Engineering, in partial fulfillment of the requirements for the degree of Master of Science, Graduate College, The University of Arizona, 2004 Aeromagnetic anomaly images are geophysical prospecting tools frequently used in the exploration of metalliferous minerals and hydrocarbons. The amplitude and texture content of these images provide a wealth of information to geophysicists who attempt to delineate the nature of the Earth's upper crust. These images prove to be extremely useful in remote areas and locations where the minerals of interest are concealed by basin fill. Typically, geophysicists compile a suite of aeromagnetic anomaly images, derived from amplitude and texture measurement operations, in order to obtain a qualitative interpretation of the lithological (rock) structure. Texture measures have proven to be especially capable of capturing the magnetic anomaly signature of unique lithological units. We performed a quantitative study to explore the possibility of using texture measures as input to a machine vision system in order to achieve automated classification of lithological units. This work demonstrated a significant improvement in classification accuracy over random guessing based on a priori probabilities. Additionally, a quantitative comparison between the performances of five classes of texture measures in their ability to discriminate lithological units was achieved.

Lithological mapping using Landsat 8 OLI and Terra ASTER multispectral data in the Bas Drâa inlier, Moroccan Anti Atlas

NASA Astrophysics Data System (ADS)

Adiri, Zakaria; Harti, Abderrazak El; Jellouli, Amine; Maacha, Lhou; Bachaoui, El Mostafa

2016-01-01

Lithological mapping is a fundamental step in various mineral prospecting studies because it forms the basis of the interpretation and validation of retrieved results. Therefore, this study exploited the multispectral Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) and Landsat 8 Operational Land Imager (OLI) data in order to map lithological units in the Bas Drâa inlier, at the Moroccan Anti Atlas. This task was completed by using principal component analysis (PCA), band ratios (BR), and support vector machine (SVM) classification. Overall accuracy and the kappa coefficient of SVM based on ground truth in addition to the results of PCA and BR show an excellent correlation with the existing geological map of the study area. Consequently, the methodology proposed demonstrates a high potential of ASTER and Landsat 8 OLI data in lithological units discrimination.

Discrimination of lithologic units of the basis of botanical associations and Landsat TM spectral data in the Ridge and Valley province, Pennsylvania

NASA Technical Reports Server (NTRS)

Price, C. V.; Birnie, R. W.; Logan, T. L.; Rock, B. N.; Parrish, J.

1986-01-01

Data collected on November 2, 1982 by the Landsat 4 Thematic Mapper (TM) over 72 forested sites in the Ridge and Valley province in Pennsylvania were compared with corresponding botanical and site variable field data. The analysis revealed that both the TM and the botanical data sets can be divided into four groups based on lithology and aspect. Lithology, which is clearly the dominant controlling factor in both sets of data, determines elevation and slope. The aspect (essentially north- and south-facing slope) determines the intensity of solar illumination which affects both the moisture available to the vegetation and the intensity of reflected radiance. Each of the four lithologic/aspect units support unique forest associations, clearly separable both on the basis of ground-based 1/10-acre forest association surveys and on the basis of their TM spectral signatures.

Improved predictive mapping of indoor radon concentrations using ensemble regression trees based on automatic clustering of geological units.

PubMed

Kropat, Georg; Bochud, Francois; Jaboyedoff, Michel; Laedermann, Jean-Pascal; Murith, Christophe; Palacios Gruson, Martha; Baechler, Sébastien

2015-09-01

According to estimations around 230 people die as a result of radon exposure in Switzerland. This public health concern makes reliable indoor radon prediction and mapping methods necessary in order to improve risk communication to the public. The aim of this study was to develop an automated method to classify lithological units according to their radon characteristics and to develop mapping and predictive tools in order to improve local radon prediction. About 240 000 indoor radon concentration (IRC) measurements in about 150 000 buildings were available for our analysis. The automated classification of lithological units was based on k-medoids clustering via pair-wise Kolmogorov distances between IRC distributions of lithological units. For IRC mapping and prediction we used random forests and Bayesian additive regression trees (BART). The automated classification groups lithological units well in terms of their IRC characteristics. Especially the IRC differences in metamorphic rocks like gneiss are well revealed by this method. The maps produced by random forests soundly represent the regional difference of IRCs in Switzerland and improve the spatial detail compared to existing approaches. We could explain 33% of the variations in IRC data with random forests. Additionally, the influence of a variable evaluated by random forests shows that building characteristics are less important predictors for IRCs than spatial/geological influences. BART could explain 29% of IRC variability and produced maps that indicate the prediction uncertainty. Ensemble regression trees are a powerful tool to model and understand the multidimensional influences on IRCs. Automatic clustering of lithological units complements this method by facilitating the interpretation of radon properties of rock types. This study provides an important element for radon risk communication. Future approaches should consider taking into account further variables like soil gas radon measurements as well as more detailed geological information. Copyright © 2015 Elsevier Ltd. All rights reserved.

Statistical Stationarity of Sediment Interbed Thicknesses in a Basalt Aquifer, Idaho National Laboratory, Eastern Snake River Plain, Idaho

USGS Publications Warehouse

Stroup, Caleb N.; Welhan, John A.; Davis, Linda C.

2008-01-01

The statistical stationarity of distributions of sedimentary interbed thicknesses within the southwestern part of the Idaho National Laboratory (INL) was evaluated within the stratigraphic framework of Quaternary sediments and basalts at the INL site, eastern Snake River Plain, Idaho. The thicknesses of 122 sedimentary interbeds observed in 11 coreholes were documented from lithologic logs and independently inferred from natural-gamma logs. Lithologic information was grouped into composite time-stratigraphic units based on correlations with existing composite-unit stratigraphy near these holes. The assignment of lithologic units to an existing chronostratigraphy on the basis of nearby composite stratigraphic units may introduce error where correlations with nearby holes are ambiguous or the distance between holes is great, but we consider this the best technique for grouping stratigraphic information in this geologic environment at this time. Nonparametric tests of similarity were used to evaluate temporal and spatial stationarity in the distributions of sediment thickness. The following statistical tests were applied to the data: (1) the Kolmogorov-Smirnov (K-S) two-sample test to compare distribution shape, (2) the Mann-Whitney (M-W) test for similarity of two medians, (3) the Kruskal-Wallis (K-W) test for similarity of multiple medians, and (4) Levene's (L) test for the similarity of two variances. Results of these analyses corroborate previous work that concluded the thickness distributions of Quaternary sedimentary interbeds are locally stationary in space and time. The data set used in this study was relatively small, so the results presented should be considered preliminary, pending incorporation of data from more coreholes. Statistical tests also demonstrated that natural-gamma logs consistently fail to detect interbeds less than about 2-3 ft thick, although these interbeds are observable in lithologic logs. This should be taken into consideration when modeling aquifer lithology or hydraulic properties based on lithology.

Change in Sediment Provenance Near the Current Estuary of Yellow River Since the Holocene Transgression

NASA Astrophysics Data System (ADS)

Song, Sheng; Feng, Xiuli; Li, Guogang; Liu, Xiao; Xiao, Xiao; Feng, Li

2018-06-01

Sedimentary sequence and sediment provenance are important factors when it comes to the studies on marine sedimentation. This paper studies grain size distribution, lithological characteristics, major and rare earth elemental compositions, micropaleontological features and 14C ages in order to examine sedimentary sequence and sediment provenance of the core BH6 drilled at the mouth of the Yellow River in Bohai Sea. According to the grain size and the micropaleontological compositions, 4 sedimentary units have been identified. Unit 1 (0-8.08 mbsf) is of the delta sedimentary facies, Unit 2 (8.08-12.08 mbsf) is of the neritic shelf facies, Unit 3 (12.08-23.85 mbsf) is of near-estuary beach-tidal facies, and Unit 4 (23.85 mbsf-) is of the continental lake facies. The deposits from Unit 1 to Unit 3 have been found to be marine strata formed after the Holocene transgression at about 10 ka BP, while Unit 4 is continental lacustrine deposit formed before 10 ka BP. The provenances of core BH6 sediments show properties of the continental crust and vary in different sedimentary periods. For Unit 4 sediments, the source regions are dispersed while the main provenance is not clear, although the parent rock characteristics of a few samples are similar to the Luanhe River sediments. For Unit 3, sediments at 21.1-23.85 mbsf have been mainly transported from the Liaohe River, while sediments above 21.1 mbsf are mainly from the Yellow River and partially from the Liaohe River. For Unit 2, the sediments have been mainly transported from the Yellow River, with a small amount from other rivers. For Unit 1, the provenance is mainly the Yellow River catchment. These results help in better understanding the evolution of the Yellow River Delta.

Lithostratigraphy does not always equal lithology: lessons learned in communicating uncertainty from stochastic modelling glacial and post glacial deposits in Glasgow U.K.

NASA Astrophysics Data System (ADS)

Kearsey, Tim; Williams, John; Finlayson, Andrew; Williamson, Paul; Dobbs, Marcus; Kingdon, Andrew; Campbell, Diarmad

2014-05-01

Geological maps and 3D models usually depict lithostragraphic units which can comprise of many different types of sediment (lithologies). The lithostratigraphic units shown on maps and 3D models of glacial and post glacial deposits in Glasgow are substantially defined by the method of the formation and age of the unit rather than its lithological composition. Therefore, a simple assumption that the dominant lithology is the most common constituent of any stratigraphic unit is erroneous and is only 58% predictive of the actual sediment types seen in a borehole. This is problematic for non-geologist such as planners, regulators and engineers attempting to use these models to inform their decisions and can lead to such users viewing maps and models as of limited use in such decision making. We explore the extent to which stochastic modelling can help to make geological models more predictive of lithology in heterolithic units. Stochastic modelling techniques are commonly used to model facies variations in oil field models. The techniques have been applied to an area containing >4000 coded boreholes to investigate the glacial and fluvial deposits in the centre of the city of Glasgow. We test the predictions from this method by deleting percentages of the control data and re-running the simulations to determine how predictability varies with data density. We also explore the best way of displaying such stochastic models to and suggest that displaying the data as probability maps rather than a single definitive answer better illustrates the uncertainties inherent in the input data. Finally we address whether is it possible truly to be able to predict lithology in such geological facies. The innovative Accessing Subsurface Knowledge (ASK) network was recently established in the Glasgow are by the British Geological Survey and Glasgow City Council to deliver and exchange subsurface data and knowledge. This provides an idea opportunity to communicate and test a range of models and to assess their usefulness and impact on a vibrant community of public and private sector partners and decision makers.

A Brief Review of the Lithology and Petrology of the Tagish Lake Meteorite Type Specimen

NASA Astrophysics Data System (ADS)

Herd, R. K.

2009-05-01

The mineralogical and textural characteristics of the type specimen of the Tagish Lake meteorite were described previously [1,2]. These initial descriptions recognized two lithologies, one relatively carbonate-poor, and the other relatively carbonate-rich. In addition numerous lithic fragments within the main lithologies were noted, essentially brecciated fragments within brecciated fragments [2,3]. Most research on the meteorite has generally assumed that only two lithologies were present. Many preliminary mineral and organic analyses done on pristine and non-pristine samples cannot be related to a particular matrix -- neither to the two supposed to be present, nor to any others. Distinction has sometimes been made between chondrule-bearing lithologies or fragments, and non-chondrule-bearing, or so-called dark dusty, lithologies preserved in the pristine specimen suite. To aid in a systematic approach to understanding this unique meteorite, the main petrographic features of the type specimen polished section are reviewed, based on back-scattered electron (BSE) images and electron- microprobe (EM) analyses. What is still needed is a consortium study of the pristine and non-pristine samples, that would define all the lithologies present and their inter-relationships, within the complete specimen suite, as the context and framework for ongoing research. [1] Brown, P.G. et al. (2000) Science, 290, 320-325. [2] Herd, R.K. et al. (2001) LPS XXXII, Abstract 1928. [3] Herd, R.K. and Herd, C.D.K. (2007) LPS XXXVIII, Abstract 2347.

Maine Geological Survey Borehole Temperature Profiles

DOE Data Explorer

Marvinney, Robert

2013-11-06

This dataset includes temperature profiles from 30 boreholes throughout Maine that were selected for their depth, location, and lithologies encountered. Depths range from about 300 feet to 2,200 feet. Most of the boreholes selected for measurement were completed in granite because this lithology can be assumed to be nearly homogeneous over the depth of the borehole. Boreholes were also selected to address gaps in existing geothermal datasets. Temperature profiles were collected in October and November, 2012.

The rare earth element geochemistry on surface sediments, shallow cores and lithological units of Lake Acıgöl basin, Denizli, Turkey

NASA Astrophysics Data System (ADS)

Budakoglu, Murat; Abdelnasser, Amr; Karaman, Muhittin; Kumral, Mustafa

2015-11-01

The sediments in Lake Acıgöl, located in SW Anatolia, Turkey, were formed under tectono-sedimentary events. REE geochemical investigations of the Lake Acıgöl sediments, from surface and shallow core sediments at different depths (0-10 cm, 10-20 cm and 20-30 cm) are presented to clarify the characteristics of REE and the nature of source rocks in the lake sediments' and to deduce their paleoenvironmental proxies. The chondrite-normalized REE patterns of these sediments are shown as light enrichment in LREE and flat HREE with a negative Eu anomaly that is close to the continental collision basin (CCB) in its profile; this is not comparable with PAAS and UCC. Inorganic detrital materials control the REE characteristics of the Lake Acıgöl sediments and these sediments were accumulated in oxic and dysoxic depositional conditions and/or at passive margins derived from oceanic island arc rocks. They were affected by low chemical weathering, either at the original source or during transport, before deposition under arid or subtropical humid climatic conditions. In addition, we used GIS techniques (such as Inverse Distance Weighted (IDW) and Geographically Weighted Regression (GWR)) to investigate the spatial interpolation and spatial correlation of the REEs from the lake surface sediments in Lake Acıgöl and its surrounding lithological units. GIS techniques showed that the lithological units (e.g., Hayrettin Formation) north of Lake Acıgöl have high REE contents; however, Eu/Eu∗ values were higher in some lake surface sediments than in lithological units, and that refers to a negative Eu-anomaly. Therefore, Lake Acıgöl sediments are derived from the weathered products, mainly from local, highly basic bedrock around the lake from the Archean crust. The chronology of Lake Acıgöl sediment was conducted using the Constant Rate of Supply (CRS) model. Using the CRS methods for the calculation of sedimentation rate, we obtained a 0.012 g/cm2/year value which is an average value for the first 20 cm depth of this lake. The core activity profiles of 210Pb and 137Cs were measured to estimate the age of the sediments; we observed activities of 8.08 ± 5.5 Bq/kg for 210Pb and 0.86 ± 0.6 Bq/kg for 137Cs.

The StreamCat Dataset: Accumulated Attributes for NHDPlusV2 Catchments (Version 2.1) for the Conterminous United States: Surficial Lithology in Watershed

EPA Pesticide Factsheets

This dataset represents the density of 18 USGS lithology classes within individual, local NHDPlusV2 catchments and upstream, contributing watersheds(see Data Sources for links to NHDPlusV2 data and USGS). Attributes were calculated for every local NHDPlusV2 catchment and then accumulated to provide watershed-level metrics for USGS lithology data. This data set is derived from the USGS raster map of 18 lithology classes (categorical data type) for the conterminous USA. The map was produced based on texture, internal structure, thickness, and environment of deposition or formation of materials. These 18 lithology classes were summarized by local catchment and by watershed to produce 18 local catchment-level and watershed-level metrics as a categorical data type (see Data Structure and Attribute Information for a description of each metric).

Crystal fractionation in the SNC meteorites: Implications for sample selection

NASA Technical Reports Server (NTRS)

Treiman, Allan H.

1988-01-01

Almost all rock types in the SNC meteorites are cumulates, products of magma differentiation by crystal fractionation (addition or removal of crystals). If the SNC meteorites are from the surface of Mars or near subsurface, then most of the igneous units on Mars are differentiated. Basaltic units probably experienced minor to moderate differientation, but ultrabasic units probably experienced extreme differentiation. Products of this differentiation may include Fe-rich gabbro, pyroxenite, periodotite (and thus serpentine), and possibly massive sulfides. The SNC meteorites include ten lithologies (three in EETA79001), eight of which are crystal cumulates. The other lithologies, EETA79001 A and B are subophitic basalts.

Testing & Validating: 3D Seismic Travel Time Tomography (Detailed Shallow Subsurface Imaging)

NASA Astrophysics Data System (ADS)

Marti, David; Marzan, Ignacio; Alvarez-Marron, Joaquina; Carbonell, Ramon

2016-04-01

A detailed full 3 dimensional P wave seismic velocity model was constrained by a high-resolution seismic tomography experiment. A regular and dense grid of shots and receivers was use to image a 500x500x200 m volume of the shallow subsurface. 10 GEODE's resulting in a 240 channels recording system and a 250 kg weight drop were used for the acquisition. The recording geometry consisted in 10x20m geophone grid spacing, and a 20x20 m stagered source spacing. A total of 1200 receivers and 676 source points. The study area is located within the Iberian Meseta, in Villar de Cañas (Cuenca, Spain). The lithological/geological target consisted in a Neogen sedimentary sequence formed from bottom to top by a transition from gyspum to silstones. The main objectives consisted in resolving the underground structure: contacts/discontinuities; constrain the 3D geometry of the lithology (possible cavities, faults/fractures). These targets were achieved by mapping the 3D distribution of the physical properties (P-wave velocity). The regularly space dense acquisition grid forced to acquire the survey in different stages and with a variety of weather conditions. Therefore, a careful quality control was required. More than a half million first arrivals were inverted to provide a 3D Vp velocity model that reached depths of 120 m in the areas with the highest ray coverage. An extended borehole campaign, that included borehole geophysical measurements in some wells provided unique tight constraints on the lithology an a validation scheme for the tomographic results. The final image reveals a laterally variable structure consisting of four different lithological units. In this methodological validation test travel-time tomography features a high capacity of imaging in detail the lithological contrasts for complex structures located at very shallow depths.

Joint Inversion of Geochemical Data and Geophysical Logs for Lithology Identification in CCSD Main Hole

NASA Astrophysics Data System (ADS)

Deng, Chengxiang; Pan, Heping; Luo, Miao

2017-12-01

The Chinese Continental Scientific Drilling (CCSD) main hole is located in the Sulu ultrahigh-pressure metamorphic (UHPM) belt, providing significant opportunities for studying the metamorphic strata structure, kinetics process and tectonic evolution. Lithology identification is the primary and crucial stage for above geoscientific researches. To release the burden of log analyst and improve the efficiency of lithology interpretation, many algorithms have been developed to automate the process of lithology prediction. While traditional statistical techniques, such as discriminant analysis and K-nearest neighbors classifier, are incompetent in extracting nonlinear features of metamorphic rocks from complex geophysical log data; artificial intelligence algorithms are capable of solving nonlinear problems, but most of the algorithms suffer from tuning parameters to be global optimum to establish model rather than local optimum, and also encounter challenges in making the balance between training accuracy and generalization ability. Optimization methods have been applied extensively in the inversion of reservoir parameters of sedimentary formations using well logs. However, it is difficult to obtain accurate solution from the logging response equations of optimization method because of the strong overlapping of nonstationary log signals when applied in metamorphic formations. As oxide contents of each kinds of metamorphic rocks are relatively less overlapping, this study explores an approach, set in a metamorphic formation model and using the Broyden Fletcher Goldfarb Shanno (BFGS) optimization algorithm to identify lithology from oxide data. We first incorporate 11 geophysical logs and lab-collected geochemical data of 47 core samples to construct oxide profile of CCSD main hole by using backwards stepwise multiple regression method, which eliminates irrelevant input logs step by step for higher statistical significance and accuracy. Then we establish oxide response equations in accordance with the metamorphic formation model and employ BFGS algorithm to minimize the objective function. Finally, we identify lithology according to the composition content which accounts for the largest proportion. The results show that lithology identified by the method of this paper is consistent with core description. Moreover, this method demonstrates the benefits of using oxide content as an adhesive to connect logging data with lithology, can make the metamorphic formation model more understandable and accurate, and avoid selecting complex formation model and building nonlinear logging response equations.

Macrostrat and GeoDeepDive: A Platform for Geological Data Integration and Deep-Time Research

NASA Astrophysics Data System (ADS)

Husson, J. M.; Peters, S. E.; Ross, I.; Czaplewski, J. J.

2016-12-01

Characterizing the quantity, lithology, age, and properties of rocks and sediments in the upper crust is central to many questions in Earth science. Although a large number of geological maps, regional syntheses, and sample-based measurements have been published in a variety of formats, there is no system for integrating and accessing rock record-derived data or for facilitating the large-scale quantitative interrogation of the physical, chemical, and biological properties of Earth's crust. Here we describe two data resources that aim to overcome some of these limitations: 1) Macrostrat, a geospatial database and supporting cyberinfrastructure that is designed to enable quantitative analyses of the entire assemblage of surface and subsurface sedimentary, igneous and metamorphic rocks, and 2) GeoDeepDive, a digital library and high throughput computing system designed to facilitate the location and extraction of information and data from the published literature. Macrostrat currently contains general summaries of the age and lithology of rocks and sediments in the upper crust at 1,474 regions in North and Central America, the Caribbean, New Zealand, and the deep sea. Distributed among these geographic regions are nearly 34,000 lithologically and chronologically-defined geological units, many of which are linked to a bedrock geologic map database with more than 1.7 million globally distributed units. Sample-derived data, including fossil occurrences in the Paleobiology Database and more than 180,000 geochemical and outcrop-derived measurements are linked to Macrostrat units and/or lithologies within those units. The rock names, lithological terms, and geological time intervals that are applied to Macrostrat units define a hierarchical, spatially and temporally indexed vocabulary that is leveraged by GeoDeepDive in order to provide researchers access to data within the scientific literature as it is published and ingested into the infrastructure. All data in Macrostrat are accessible via an Application Programming Interface, which enables the development of mobile and analytical applications. The GeoDeepDive infrastructure also supports the development and execution of applications that are tailored to the specific, literature-based data location and extraction needs of geoscientists.

Estimating Last Glacial Maximum Ice Thickness Using Porosity and Depth Relationships: Examples from AND-1B and AND-2A Cores, McMurdo Sound, Antarctica

NASA Astrophysics Data System (ADS)

Hayden, T. G.; Kominz, M. A.; Magens, D.; Niessen, F.

2009-12-01

We have estimated ice thicknesses at the AND-1B core during the Last Glacial Maximum by adapting an existing technique to calculate overburden. As ice thickness at Last Glacial Maximum is unknown in existing ice sheet reconstructions, this analysis provides constraint on model predictions. We analyze the porosity as a function of depth and lithology from measurements taken on the AND-1B core, and compare these results to a global dataset of marine, normally compacted sediments compiled from various legs of ODP and IODP. Using this dataset we are able to estimate the amount of overburden required to compact the sediments to the porosity observed in AND-1B. This analysis is a function of lithology, depth and porosity, and generates estimates ranging from zero to 1,000 meters. These overburden estimates are based on individual lithologies, and are translated into ice thickness estimates by accounting for both sediment and ice densities. To do this we use a simple relationship of Xover * (ρsed/ρice) = Xice; where Xover is the overburden thickness, ρsed is sediment density (calculated from lithology and porosity), ρice is the density of glacial ice (taken as 0.85g/cm3), and Xice is the equalivant ice thickness. The final estimates vary considerably, however the “Best Estimate” behavior of the 2 lithologies most likely to compact consistently is remarkably similar. These lithologies are the clay and silt units (Facies 2a/2b) and the diatomite units (Facies 1a) of AND-1B. These lithologies both produce best estimates of approximately 1,000 meters of ice during Last Glacial Maximum. Additionally, while there is a large range of possible values, no combination of reasonable lithology, compaction, sediment density, or ice density values result in an estimate exceeding 1,900 meters of ice. This analysis only applies to ice thicknesses during Last Glacial Maximum, due to the overprinting effect of Last Glacial Maximum on previous ice advances. Analysis of the AND-2A core is underway, and results will be compared to those of AND-1B.

Hydrogeologic framework of the middle San Pedro watershed, southeastern Arizona

USGS Publications Warehouse

Dickinson, Jesse; Kennedy, Jeffrey R.; Pool, D.R.; Cordova, Jeffrey T.; Parker, John T.; Macy, J.P.; Thomas, Blakemore

2010-01-01

Water managers in rural Arizona are under increasing pressure to provide sustainable supplies of water despite rapid population growth and demands for environmental protection. This report describes the results of a study of the hydrogeologic framework of the middle San Pedro watershed. The components of this report include: (1) a description of the geologic setting and depositional history of basin fill sediments that form the primary aquifer system, (2) updated bedrock altitudes underlying basin fill sediments calculated using a subsurface density model of gravity data, (3) delineation of hydrogeologic units in the basin fill using lithologic descriptions in driller's logs and models of airborne electrical resistivity data, (4) a digital three-dimensional (3D) hydrogeologic framework model (HFM) that represents spatial extents and thicknesses of the hydrogeologic units (HGUs), and (5) description of the hydrologic properties of the HGUs. The lithologic interpretations based on geophysical data and unit thickness and extent of the HGUs included in the HFM define potential configurations of hydraulic zones and parameters that can be incorporated in groundwater-flow models. The hydrogeologic framework comprises permeable and impermeable stratigraphic units: (1) bedrock, (2) sedimentary rocks predating basin-and-range deformation, (3) lower basin fill, (4) upper basin fill, and (5) stream alluvium. The bedrock unit includes Proterozoic to Cretaceous crystalline rocks, sedimentary rocks, and limestone that are relatively impermeable and poor aquifers, except for saturated portions of limestone. The pre-basin-and-range sediments underlie the lower basin fill but are relatively impermeable owing to cementation. However, they may be an important water-bearing unit where fractured. Alluvium of the lower basin fill, the main water-bearing unit, was deposited in the structural trough between the uplifted ridges of bedrock and (or) pre-basin-and-range sediments. Alluvium of the upper basin fill may be more permeable than the lower basin fill, but it is generally unsaturated in the study area. The lower basin fill stratigraphic unit was delineated into three HGUs on the basis of lithologic descriptions in driller?s logs and one-dimensional (1D) electrical models of airborne transient electromagnetic (TEM) surveys. The interbedded lower basin fill (ILBF) HGU represents an upper sequence having resistivity values between 5 and 40 ohm-m identified as interbedded sand, gravel, and clay in driller?s logs. Below this upper sequence, fine-grained lower basin fill (FLBF) HGU represents a thick silt and clay sequence having resistivity values between 5 and 20 ohm-m. Within the coarse-grained lower basin fill (CLBF) HGU, which underlies the silt and clay of the FLBF, the resistivity values on logs and 1D models increase to several hundred ohm-m and are highly variable within sand and gravel layers. These sequences match distinct resistivity and lithologic layers identified by geophysical logs in the adjacent Sierra Vista subwatershed, suggesting that these sequences are laterally continuous within both the Benson and Sierra Vista subwatersheds in the Upper San Pedro Basin. A subsurface density model based on gravity data was constructed to identify the top of bedrock and structures that may affect regional groundwater flow. The subsurface density model contains six layers having uniform density values, which are assigned on the basis of geophysical logs. The density values for the layers range between 1.65 g/cm3 for unsaturated sediments near the land surface and 2.67 g/cm3 for bedrock. Major features include three subbasins within the study area, the Huachuca City subbasin, the Tombstone subbasin, and the Benson subbasin, which have no expression in surface topography or lithology. Bedrock altitudes from the subsurface density model defined top altitudes of the bedrock HGU. The HFM includes the following HGUs in ascending stratigr

Preliminary Integrated Geologic Map Databases for the United States: Connecticut, Maine, Massachusetts, New Hampshire, New Jersey, Rhode Island and Vermont

USGS Publications Warehouse

Nicholson, Suzanne W.; Dicken, Connie L.; Horton, John D.; Foose, Michael P.; Mueller, Julia A.L.; Hon, Rudi

2006-01-01

The rapid growth in the use of Geographic Information Systems (GIS) has highlighted the need for regional and national scale digital geologic maps that have standardized information about geologic age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. Although two digital geologic maps (Schruben and others, 1994; Reed and Bush, 2004) of the United States currently exist, their scales (1:2,500,000 and 1:5,000,000) are too general for many regional applications. Most states have digital geologic maps at scales of about 1:500,000, but the databases are not comparably structured and, thus, it is difficult to use the digital database for more than one state at a time. This report describes the result for a seven state region of an effort by the U.S. Geological Survey to produce a series of integrated and standardized state geologic map databases that cover the entire United States. In 1997, the United States Geological Survey's Mineral Resources Program initiated the National Surveys and Analysis (NSA) Project to develop national digital databases. One primary activity of this project was to compile a national digital geologic map database, utilizing state geologic maps, to support studies in the range of 1:250,000- to 1:1,000,000-scale. To accomplish this, state databases were prepared using a common standard for the database structure, fields, attribution, and data dictionaries. For Alaska and Hawaii new state maps are being prepared and the preliminary work for Alaska is being released as a series of 1:250,000 scale quadrangle reports. This document provides background information and documentation for the integrated geologic map databases of this report. This report is one of a series of such reports releasing preliminary standardized geologic map databases for the United States. The data products of the project consist of two main parts, the spatial databases and a set of supplemental tables relating to geologic map units. The datasets serve as a data resource to generate a variety of stratigraphic, age, and lithologic maps. This documentation is divided into four main sections: (1) description of the set of data files provided in this report, (2) specifications of the spatial databases, (3) specifications of the supplemental tables, and (4) an appendix containing the data dictionaries used to populate some fields of the spatial database and supplemental tables.

Effects of model layer simplification using composite hydraulic properties

USGS Publications Warehouse

Kuniansky, Eve L.; Sepúlveda, Nicasio; Elango, Lakshmanan

2011-01-01

Groundwater provides much of the fresh drinking water to more than 1.5 billion people in the world (Clarke et al., 1996) and in the United States more that 50 percent of citizens rely on groundwater for drinking water (Solley et al., 1998). As aquifer systems are developed for water supply, the hydrologic system is changed. Water pumped from the aquifer system initially can come from some combination of inducing more recharge, water permanently removed from storage, and decreased groundwater discharge. Once a new equilibrium is achieved, all of the pumpage must come from induced recharge and decreased discharge (Alley et al., 1999). Further development of groundwater resources may result in reductions of surface water runoff and base flows. Competing demands for groundwater resources require good management. Adequate data to characterize the aquifers and confining units of the system, like hydrologic boundaries, groundwater levels, streamflow, and groundwater pumping and climatic data for recharge estimation are to be collected in order to quantify the effects of groundwater withdrawals on wetlands, streams, and lakes. Once collected, three-dimensional (3D) groundwater flow models can be developed and calibrated and used as a tool for groundwater management. The main hydraulic parameters that comprise a regional or subregional model of an aquifer system are the hydraulic conductivity and storage properties of the aquifers and confining units (hydrogeologic units) that confine the system. Many 3D groundwater flow models used to help assess groundwater/surface-water interactions require calculating ?effective? or composite hydraulic properties of multilayered lithologic units within a hydrogeologic unit. The calculation of composite hydraulic properties stems from the need to characterize groundwater flow using coarse model layering in order to reduce simulation times while still representing the flow through the system accurately. The accuracy of flow models with simplified layering and hydraulic properties will depend on the effectiveness of the methods used to determine composite hydraulic properties from a number of lithologic units.

Aquifer-nomenclature guidelines

USGS Publications Warehouse

Laney, R.L.; Davidson, C.B.

1986-01-01

Guidelines and recommendations for naming aquifers are presented to assist authors of geohydrological reports in the United States Geological Survey, Water Resources Division. The hierarchy of terms that is used for water- yielding rocks from largest to smallest is aquifer system, aquifer, and zone. If aquifers are named, the names should be derived from lithologic terms, rock-stratigraphic units, or geographic names. The following items are not recommended as sources of aquifer names: time-stratigraphic names, relative position, alphanumeric designations, depositional environment, depth of occurrence, acronyms, and hydrologic conditions. Confining units should not be named unless doing so clearly promotes understanding of a particular aquifer system. Sources of names for confining units are similar to those for aquifer names, i.e. lithologic terms, rock-stratigraphic units or geographic names. Examples of comparison charts and tables that are used to define the geohydrologic framework are included. Aquifers are defined in 11 hypothetical examples that characterize geohydrologic settings throughout the country. (Author 's abstract)

Controls on Deep Seated Gravitational Slope Deformations in the European Alps

NASA Astrophysics Data System (ADS)

Crosta, Giovanni B.; Frattini, Paolo; Agliardi, Federico

2013-04-01

DSGSDs are very large, slow mass movements affecting entire high-relief valley slopes. The first orogen-scale inventory of such phenomena at has been recently presented for the European Alps (Crosta et al 2008, Agliardi et al 2012), and then further implemented. The inventory includes 1034 Deep Seated Gravitational Slope Deformations, widespread over the entire orogen and clustered along major valleys and in some specific sectors of the Alps. In this contribution we systematically explore lithological, structural and topographic controls on DSGSD distribution with the help of multivariate statistical techniques (Principal Component Analysis, Discriminant Analysis). Analysis units for statistical analysis were obtained by creating three square vector grids with 2.5 km, 5 km and 10 km grid cell size, respectively, covering the entire area (about 110,000 km2). For each grid cell, we calculated the density of DSGSD, and we assigned a value for each of the controlling variable considered in the analysis. From the NASA SRTM (Shuttle Radar Topography Mission) DEM we derived land surface parameters, such as relief, slope gradients, slope aspect, mean vertical distance from base level and ruggedness. The SRTM DEM was also used to extract the drainage density, with a threshold of 1 km2 and 10 km2. We also computer the stream power of the 1km2 river network Lithology was obtained by assembling different geological maps (1:200.000 map of Salzburg, 1:250.000 map of France, 1:500.000 maps of Switzerland and Austria, 1:1.000.000 map of Italy) and by reclassifying the geological units into 8 lithological classes (carbonate rocks, metapelites, sandstones and marls, paragneiss, ortogneiss, flysch-type rocks, granitoid/metabasite, Quaternary units, and volcanic rocks). To study the role of seismicity, we calculated the number of earthquakes (CPTI11 and USGS-NEIC database) within a distance dmax from the square cell, calculated adopting Keefer's (1984) equation, and the sum of Arias Intensities of all earthquakes lying within dmax. Fission-track ages on apatite have been collected from published sources, and interpolated over the entire Alps by using a natural-neighbour interpolator. Finally, the ice thickness during the Last Glacial Maximum, the modern rock uplift, and the mean annual rainfall have been used. Results of the multivariate statistical analysis confirm the results of the previous orogen-scale investigations (Crosta et al., 2008; Agliardi et al., 2012) and shed new light on the relative importance of the (positive or negative) contributions of different controlling factors. The most important controls on DSGSD distribution are: lithology, landscape morphology, LGM ice thickness, modern uplift rate and mean annual rainfall. Lithology is the dominant factor, with units highly favourable (chiefly metapelites, followed by paragneiss and flysch-type rocks) and other unfavourable (especially carbonates rocks) to DSGSD. Landscape morphology plays a role that is difficult to correctly evaluate because of the interplay between morphology and geological and hydrological parameters. DSGSDs are more frequent along main alpine valleys, where long and regular slopes can accommodate these large phenomena, but also where the action of glaciers and the presence of main tectonic lineaments are more important. Favourable landscape morphologies seem also controlled by exhumation and uplift rate. Mean annual rainfall is inversely correlated with DSGSD density. This can be interpreted as the long-term effects of climate in shaping large-scale topography and favouring other types of landslides as players of long-term erosion. Crosta, G.B., Agliardi, F., Frattini, P., Zanchi, A. (2008) Alpine inventory of Deep-Seated Gravitational Slope Deformations. Vol. 10, EGU2008-A-02709, 2008, SRef-ID: 1607-7962/gra/EGU2008-A-0270. Agliardi, F., Crosta, G., Frattini, P. (2012). Slow rock-slope deformation. In: Clague JJ;Stead D;(eds). Landslides Types, Mechanisms and Modeling. p. 207-221, Cambridge University Press, ISBN: 978-1-107-00206-7.

Remote sensing applied to geological mapping; comparative geomorphology and identification of mineral zones of zinc and lead in the region of Vazante, MG. [Brazil

NASA Technical Reports Server (NTRS)

Nascimento, F. S. D. (Principal Investigator); Nascimento, M. A. L. S. D.

1977-01-01

The author has identified the following significant results. Results showed that the black and white aerial photographs and the color infrared transparencies were efficient for mapping of three lithological units of the Paraopeba formation and for mineralized zones identification, respectively. Multispectral transparencies of I2S made it easier to separate dolomites, which were the rocks conditioning zinc and lead mineralization. Statistical analysis of morphometric indexes obtained from black and white photographs and topographic charts showed significant difference among three lithological units of Paraopeba formation which can be defined as Crest, Hilly, and Karstic reliefs.

Unsupervised learning on scientific ocean drilling datasets from the South China Sea

NASA Astrophysics Data System (ADS)

Tse, Kevin C.; Chiu, Hon-Chim; Tsang, Man-Yin; Li, Yiliang; Lam, Edmund Y.

2018-06-01

Unsupervised learning methods were applied to explore data patterns in multivariate geophysical datasets collected from ocean floor sediment core samples coming from scientific ocean drilling in the South China Sea. Compared to studies on similar datasets, but using supervised learning methods which are designed to make predictions based on sample training data, unsupervised learning methods require no a priori information and focus only on the input data. In this study, popular unsupervised learning methods including K-means, self-organizing maps, hierarchical clustering and random forest were coupled with different distance metrics to form exploratory data clusters. The resulting data clusters were externally validated with lithologic units and geologic time scales assigned to the datasets by conventional methods. Compact and connected data clusters displayed varying degrees of correspondence with existing classification by lithologic units and geologic time scales. K-means and self-organizing maps were observed to perform better with lithologic units while random forest corresponded best with geologic time scales. This study sets a pioneering example of how unsupervised machine learning methods can be used as an automatic processing tool for the increasingly high volume of scientific ocean drilling data.

Identification of critical sediment source areas at regional level

NASA Astrophysics Data System (ADS)

Fargas, D.; Casasnovas, J. A. Martínez; Poch, R.

In order to identify critical sediment sources in large catchments, using easily available terrain information at regional scale, a methodology has been developed to obtain a qualitative assessment necessary for further studies. The main objective of the model is to use basic terrain data related to the erosive processes which contribute to the production, transport and accumulation of sediments through the main water paths in the watershed. The model is based on the selection of homogeneous zones regarding drainage density and lithology, achieved by joining the spatial basic units by a rating system. The values of drainage density are rated according to an erosion class (Bucko & Mazurova, 1958). The lithology is rated by erosion indexes, adapted from FAO (1977). The combination and reclassification of the results brings about five qualitative classes of sediment emission risk. This methodology has been tested an validated for the watershed of the Joaquín Costa reservoir (NE Spain), with a surface of 1500 km 2. The mapping scale was 1:100.000 and the model was implemented through a vector GIS (Arc/Info). The prediction was checked by means of photo-interpretation and field work, which gave a accuracy of 78.5%. The proposed methodology has been proved useful as an initial approach for erosion assessment and soil conservation planning at the regional level, and also to select priority areas where further analyses can be developed.

Applicability of radon emanometry in lithologically discontinuous sites contaminated by organic chemicals.

PubMed

De Miguel, Eduardo; Barrio-Parra, Fernando; Elío, Javier; Izquierdo-Díaz, Miguel; García-González, Jerónimo Emilio; Mazadiego, Luis Felipe; Medina, Rafael

2018-06-02

The applicability of radon ( 222 Rn) measurements to delineate non-aqueous phase liquids (NAPL) contamination in subsoil is discussed at a site with lithological discontinuities through a blind test. Three alpha spectroscopy monitors were used to measure radon in soil air in a 25,000-m 2 area, following a regular sampling design with a 20-m 2 grid. Repeatability and reproducibility of the results were assessed by means of duplicate measurements in six sampling positions. Furthermore, three points not affected by oil spills were sampled to estimate radon background concentration in soil air. Data histograms, Q-Q plots, variograms, and cluster analysis allowed to recognize two data populations, associated with the possible path of a fault and a lithological discontinuity. Even though the concentration of radon in soil air was dominated by this discontinuity, the characterization of the background emanation in each lithological unit allowed to distinguish areas potentially affected by NAPL, thus justifying the application of radon emanometry as a screening technique for the delineation of NAPL plumes in sites with lithological discontinuities.

Cooling History of Almahata Sitta Ureilite as Inferred from Transmission Electron Microscopy of Iron Metal

NASA Technical Reports Server (NTRS)

Mikouchi, T.; Aoyagi, Y.; Goodrich, C. A.; Yubuta, K.; Sugiyama, K.; Zolensky, M. E.; Goldstein, J. I.

2013-01-01

Almahata Sitta (AS) is a polymict breccia mainly composed of various ureilite lithologies with lesser chondritic lithologies [1]. In the ureilite lithologies, Fe metal is a common accessory phase present either as large grain boundary grains or small particles formed by reduction of olivine and pyroxene. In our earlier studies on grain boundary metals in one of AS fragments (#44) we found unique features never seen in other ureilites [2,3]. In order to further characterize these metal grains, we performed a detailed TEM study on a FIB section prepared from one of AS #44 grain boundary metals and here discuss its thermal history.

Initial Isotopic Heterogeneities in ZAGAMI: Evidence of a Complex Magmatic History

NASA Technical Reports Server (NTRS)

Nyquist, L. E.; Shih, C.-Y.; Reese, Y. D.

2006-01-01

Interpretations of Zagami s magmatic history range from complex [1,2] to relatively simple [3]. Discordant radiometric ages led to a suggestion that the ages had been reset [4]. In an attempt to identify the mechanism, Rb-Sr isochrons were individually determined for both fine-grained and coarse-grained Zagami [5]. Ages of approx.180 Ma were obtained from both lithologies, but the initial Sr-87/Sr-86 (ISr) of the fine-grained lithology was higher by 8.6+/-0.4 e-units. Recently, a much older age of approx.4 Ga has been advocated [6]. Here, we extend our earlier investigation [5]. Rb-Sr Data: In [5] we applied identical, simplified, procedures to both lithologies to test whether a grain-size dependent process such as thermally-driven subsolidus isotopic reequilibration had caused age-resetting. Minerals were separated only by density. In the present experiment, purer mineral separates were analysed with improved techniques. Combined Rb-Sr results give ages (T) = 166+/-12 Ma and 177+/-9 Ma and I(subSr) = 0.72174+/-9 and 0.72227+/-7 for the coarse-grained and fine-grained lithologies, respectively. ISr in the fine-grained sample is thus higher than in the coarse-grained sample by 7.3+/-1.6 e-units. The results for the coarse-grained lithology are in close agreement with T = 166+/-6 Ma, ISr = 0.72157+/-8 for an adjacent sample [7] and T = 178+/-4 Ma, ISr = 0.72151+/-5 [4, adjusted] for a separate sample. Thus, fine-grained Zagami appears on average to be less typical of the bulk than coarse-grained Zagami.

Alteration minerals in impact-generated hydrothermal systems - Exploring host rock variability

NASA Astrophysics Data System (ADS)

Schwenzer, Susanne P.; Kring, David A.

2013-09-01

Impact-generated hydrothermal systems have been previously linked to the alteration of Mars’ crust and the production of secondary mineral assemblages seen from orbit. The sensitivity of the resultant assemblages has not yet been evaluated as a function of precursor primary rock compositions. In this work, we use thermochemical modeling to explore the variety of minerals that could be produced by altering several known lithologies based on martian meteorite compositions. For a basaltic host rock lithology (Dhofar 378, Humphrey) the main alteration phases are feldspar, zeolite, pyroxene, chlorite, clay (nontronite, kaolinite), and hematite; for a lherzolithic host rock lithology (LEW 88516) the main alteration phases are amphibole, serpentine, chlorite, clay (nontronite, kaolinite), and hematite; and for an ultramafic host rock lithology (Chassigny) the main minerals are secondary olivine, serpentine, magnetite, quartz, and hematite. These assemblages and proportions of phases in each of those cases depend on W/R and temperature. Integrating geologic, hydrologic and alteration mineral evidence, we have developed a model to illustrate the distribution of alteration assemblages that occur in different levels of an impact structure. At the surface, hot, hydrous alteration affects the ejecta and melt sheet producing clay and chlorite. Deeper in the subsurface and depending on the permeability of the rock, a variety of minerals - smectite, chlorite, serpentine, amphiboles and hematite - are produced in a circulating hydrothermal system. These modeled mineral distributions should assist with interpretation of orbital observations and help guide surface exploration by rovers and sample return assets.

Knickpoints and Hanging Valleys of Licus Vallis, Mars

NASA Astrophysics Data System (ADS)

Goudge, T. A.; Fassett, C.

2016-12-01

Licus Vallis is a 350 km long valley system located along the dichotomy boundary on Mars. The main trunk of the valley is incised 200-700 m into the surrounding terrain. The valley heads at an outlet breach of a shallow, 30 km diameter impact crater, and is also fed by a system of tributaries incised into the plateau surrounding Licus Vallis. Many of the tributary valleys, as well as the main stem of the valley fed by the paleolake outlet, have profiles that are not smoothly graded, but rather have distinct reaches with concave downward topography. These sections are either knickpoints or hanging valleys that develop in response to changes in the effective local base level, changes in climate conditions during incision of the valley, or lithologic boundaries in the substrate. Here we present remote sensing observations from images and topography to test these competing hypotheses and further characterize the evolution of this large valley system. Slope-watershed area relationships for the tributaries and main trunk valley are used to distinguish between knickpoints and hanging valleys. Analysis of orbital images does not reveal any distinct layer above which knickpoints develop, and the elevation of knickpoints show no systematic trends that might be expected of a regional lithologic unit(s). Our preliminary results suggest that the distance of knickpoint retreat is correlated with the position of the tributary valley and not the watershed area. Downstream valleys have retreated the most, suggesting they have had the most time to adjust to lowering of the local base level associated with incision of the main valley. These results are most consistent with a wave of incision sweeping up the valley system as it adjusts to a low base level in the northern plains. This conclusion is also consistent with observations of the incision depth of Licus Vallis, which increases approximately linearly downstream. Understanding this signature of base level control on the incision of valley network systems such as Licus Vallis provides a unique opportunity to develop predictions for the evolution of regional hydrology and the martian hydrologic cycle.

Igneous stratigraphy and rock-types from a deep transect of the gabbroic lower crust of the Atlantis Bank core complex (SW Indian Ridge): preliminary results from IODP Expedition 360

NASA Astrophysics Data System (ADS)

Sanfilippo, A.; France, L.; Ghosh, B.; Liu, C. Z.; Morishita, T.; Natland, J. H.; Dick, H. J.; MacLeod, C. J.; Expedition 360 Scientists, I.

2016-12-01

International Ocean Discovery Program (IODP) Expedition 360 represents the first leg of a multi-phase drilling programme ('SloMo' project) aimed at investigating the nature of the lower crust and Moho at slow spreading ridges. As an initial phase of the SloMo project, IODP Exp. 360 intended to recover a representative transect of the lower oceanic crust formed at Atlantis Bank, an oceanic core complex on the SW Indian Ridge. During this expedition, 89 cores of gabbroic rocks were recovered at Hole U1473A, drilled to 789.7 m below seafloor. This hole was subsequently deepened to 809.4 mbsf during transit Expedition 362T, which recovered additional 7 cores. The gabbroic section recovered at Hole U1473A consists of several types of gabbro, diabase, and felsic veins. The main lithology is dominated by olivine gabbro (76.5% in abundance), followed by gabbro containing 1-2% oxide (9.5%), gabbro with >2% oxide (7.4%), gabbro sensu stricto (5.1%), felsic veins (1.5%) and diabase (<0.5%). The different lithologies appear randomly distributed throughout the section, although oxide abundance seems to decrease slightly downhole, except for the lowermost intervals where oxide gabbros are more abundant. Based on changes in rock types, grain size, texture, and the occurrence of felsic material, we identified eight lithologic units, which locally define separate geochemical trends. Each unit is characterized by meter-scale heterogeneity which classically characterizes gabbros formed at slow spreading ridges. Reaction textures in olivine gabbros, crosscutting relationships between oxide gabbros and host rocks, the presence of intrusive to sutured contacts, igneous layering and the widespread occurrence of felsic veins and segregations indicate that the evolution of this section was controlled by complicated interactions of magmatic processes, e.g., fractional crystallization, melt-rock reaction, late-stage melt migration, which were active in a crystal mush formed by multiple injections of magma. This contribution describes the main features of these rocks and discusses the complexity of the igneous processes producing this 800 m-long transect of oceanic crust that was formed in a robust magmatic segment of an ultraslow spreading ridge.

Characterizing the natural radiation levels throughout the main geological units of Sabkhat al Jabboul area, northern Syria.

PubMed

Al-Hilal, Mohamed; Aissa, Mosa

2015-02-01

The concentrations of equivalent eU, eTh, and K% were determined together with soil gas radon values and carborne gamma-ray survey in order to define the natural radioactivity levels throughout main geological units of Sabkhat al Jabboul region. Forty five soil and rock samples were collected from various lithofacies in each geological unit, and analyzed by γ-ray spectrometric technique for determining the concentration values of major radioelements. Such radiometric data could be used to differentiate between various lithologies of the investigated rocks. Although no distinct radioactive anomalies were found in the area, the radiometric profiles showed some minor variations with slightly higher values than the normal level. Despite the low radioactivity and the lack of rocks diversity in the surveyed area, it was possible to classify some certain rock types based on their radiometric response. The relationships between eU, eTh and their ratios were discussed for the Quaternary, Neogene and Paleogene formations, in order to evaluate the degree of uranium distribution and remobilization. The overall results of this radiometric survey were generally low, and lying within the range of the normal background levels in Syrian. Copyright © 2014 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruno, C.; Eichenseer, H.; Calatayud, P.

The poster illustrates how the recent developments in genetic stratigraphy have contributed to constrain reservoir layering and to improve prediction of reservoir quality in the oil-bearing reservoir of N`KOSSA. The mixed lithology deposits formed during Albian times. Thanks to the excellent core coverage of the reservoir (4 cored wells over the entire reservoir interval), continuous sedimentological examination and interpretation of the facies succession have been carried out. The reservoir can be subdivided into composite sequences (50 to 150 in thick) which are made up of stacked metre-scale genetic units. Three different stacking patterns of genetic units have been identified; retrogradation,more » aggradation and progradation. These patterns reflect a gradual change of depositional regimes through time. Facies variations (texture, bio-association, geometry, spatial distribution) and early diagenetic overprints can be related to each type of stacking pattern. One additional model illustrates the depositional regime corresponding to low accomodation periods which mainly record siliciclastic input and extensive carbonate diagenesis by meteoric waters The resulting four models show the overall distribution of the main depositional units, the diagenetic zonations and the resulting overall reservoir qualities. This above approach have contributed to a more detailed reservoir architecture and a better delineation of reservoir heterogeneity due to both depositional and diagenetic regimes.« less

Lower crustal section of the Oman Ophiolite drilled in Hole GT1A, ICDP Oman Drilling Project

NASA Astrophysics Data System (ADS)

Umino, S.; Kelemen, P. B.; Matter, J. M.; Coggon, J. A.; Takazawa, E.; Michibayashi, K.; Teagle, D. A. H.

2017-12-01

Hole GT1A (22° 53.535'N, 58° 30.904'E) was drilled by the Oman Drilling Project (OmDP) into GT1A of the Samail ophiolite, Oman. OmDP is an international collaboration supported by the International Continental Scientific Drilling Program, the Deep Carbon Observatory, NSF, IODP, JAMSTEC, and the European, Japanese, German and Swiss Science Foundations, with in-kind support in Oman from the Ministry of Regional Municipalities and Water Resources, Public Authority of Mining, Sultan Qaboos University, and the German University of Technology. Hole GT1A was diamond cored in 22 Jan to 08 Feb 2017 to a total depth of 403.05 m. The outer surfaces of the cores were imaged and described on site before being curated, boxed and shipped to the IODP drill ship Chikyu, where they underwent comprehensive visual and instrumental analysis. Hole GT1A drilled the lower crustal section in the southern Oman Ophiolite and recovered 401.52 m of total cores (99.6% recovery). The main lithology is dominated by olivine gabbro (65.9%), followed in abundance by olivine-bearing gabbro (21.5%) and olivine melagabbro (3.9%). Minor rock types are orthopyroxene-bearing olivine gabbro (2.4%), oxide-bearing olivine gabbro (1.5%), gabbro (1.1%), anorthositic gabbro (1%), troctolitic gabbro (0.8%); orthopyroxene-bearing gabbro (0.5%), gabbronorite (0.3%); and dunite (0.3%). These rocks are divided into Lithologic Unit I to VII at 26.62 m, 88.16 m, 104.72 m, 154.04 m, 215.22 m, 306.94 m in Chikyu Curated Depth in descending order; Unit I and II consist of medium-grained olivine gabbro with lower olivine abundance in Unit II. Unit III is medium-grained olivine melagabbros, marked by an increase in olivine. Unit IV is relatively homogenous medium-grained olivine gabbros with granular textures. Unit V is identified by the appearance of fine-grained gabbros, but the major rocktypes are medium grained olivine gabbros. Unit VI is medium-grained olivine gabbro, marked by appearance of orthopyroxene. Unit VII is of fine- to medium-grained olivine gabbros with less olivine.

Analysis of ERTS-1 imagery of Wyoming and its application to evaluation of Wyoming's natural resources

NASA Technical Reports Server (NTRS)

Houston, R. S. (Principal Investigator); Marrs, R. W.

1972-01-01

The author has identified the following significant results. The major effort has been toward interpretation of the intermediate and high altitude aircraft data which was available. Project investigators were able to delineate various structures and lithologic units in well-exposed sedimentary sequences and in regions of Precambrian igneous and metamorphic rocks. In one area, the Precambrian lithologies, which were previously unmapped, include a taconite formation which might be economically important.

Geohydrology of the High Energy Laser System Test Facility site, White Sands Missile Range, Tularosa Basin, south-central New Mexico

USGS Publications Warehouse

Basabilvazo, G.T.; Nickerson, E.L.; Myers, R.G.

1994-01-01

The Yesum-HoHoman and Gypsum land (hummocky) soils at the High Energy Laser System Test Facility (HELSTF) represent wind deposits from recently desiccated lacustrine deposits and deposits from the ancestral Lake Otero. The upper 15-20 feet of the subsurface consists of varved gypsiferous clay and silt. Below these surfidai deposits the lithology consists of interbedded clay units, silty-clay units, and fine- to medium-grained quartz arenite units in continuous and discontinuous horizons. Clay horizons can cause perched water above the water table. Analyses of selected clay samples indicate that clay units are composed chiefly of kaolinire and mixed-layer illite/ smectite. The main aquifer is representative of a leaky-confined aquifer. Estimated aquifer properties are: transmissivity (T) = 780 feet squared per day, storage coefficient (S) = 3.1 x 10-3, and hydraulic conductivity (K) = 6.0 feet per day. Ground water flows south and southwest; the estimated hydraulic gradient is 5.3 feet per mile. Analyses of water samples indicate that ground water at the HELSTF site is brackish to slightly saline at the top of the main aquifer. Dissolved-solids concentration near the top of the main aquifer ranges from 5,940 to 11,800 milligrams per liter. Predominant ions are sodium and sulfate. At 815 feet below land surface, the largest dissolved-solids concentration measured is 111,000 milligrams per liter, which indicates increasing salinity with depth. Predominant ions are sodium and chloride.

Petrologic Characteristics of the Lunar Surface

NASA Astrophysics Data System (ADS)

Wang, Xianmin; Pedrycz, Witold

2015-11-01

Petrologic analysis of the lunar surface is critical for determining lunar formation and evolution. Here, we report the first global petrologic map that includes the five most important lunar lithological units: the Ferroan Anorthositic (FAN) Unit, the Magnesian Suite (MS) Unit, the Alkali Suite (AS) Unit, the KREEP Basalt (KB) Unit and the Mare Basalt (MB) Unit. Based on the petrologic map and focusing on four long-debated and important issues related to lunar formation and evolution, we draw the following conclusions from the new insights into the global distribution of the five petrologic units: (1) there may be no petrogenetic relationship between MS rocks and KB; (2) there may be no petrogenetic link between MS and AS rocks; (3) the exposure of the KREEP component on the lunar surface is likely not a result of MB volcanism but is instead mainly associated with the combined action of plutonic intrusion, KREEP volcanism and celestial collision; (4) the impact size of the South Pole-Aitken basin is constrained, i.e., the basin has been excavated through the whole crust to exhume a vast majority of lower-crustal material and a very limited mantle components to the lunar surface.

Petrologic Characteristics of the Lunar Surface

PubMed Central

Wang, Xianmin; Pedrycz, Witold

2015-01-01

Petrologic analysis of the lunar surface is critical for determining lunar formation and evolution. Here, we report the first global petrologic map that includes the five most important lunar lithological units: the Ferroan Anorthositic (FAN) Unit, the Magnesian Suite (MS) Unit, the Alkali Suite (AS) Unit, the KREEP Basalt (KB) Unit and the Mare Basalt (MB) Unit. Based on the petrologic map and focusing on four long-debated and important issues related to lunar formation and evolution, we draw the following conclusions from the new insights into the global distribution of the five petrologic units: (1) there may be no petrogenetic relationship between MS rocks and KB; (2) there may be no petrogenetic link between MS and AS rocks; (3) the exposure of the KREEP component on the lunar surface is likely not a result of MB volcanism but is instead mainly associated with the combined action of plutonic intrusion, KREEP volcanism and celestial collision; (4) the impact size of the South Pole-Aitken basin is constrained, i.e., the basin has been excavated through the whole crust to exhume a vast majority of lower-crustal material and a very limited mantle components to the lunar surface. PMID:26611148

Petrologic Characteristics of the Lunar Surface.

PubMed

Wang, Xianmin; Pedrycz, Witold

2015-11-27

Petrologic analysis of the lunar surface is critical for determining lunar formation and evolution. Here, we report the first global petrologic map that includes the five most important lunar lithological units: the Ferroan Anorthositic (FAN) Unit, the Magnesian Suite (MS) Unit, the Alkali Suite (AS) Unit, the KREEP Basalt (KB) Unit and the Mare Basalt (MB) Unit. Based on the petrologic map and focusing on four long-debated and important issues related to lunar formation and evolution, we draw the following conclusions from the new insights into the global distribution of the five petrologic units: (1) there may be no petrogenetic relationship between MS rocks and KB; (2) there may be no petrogenetic link between MS and AS rocks; (3) the exposure of the KREEP component on the lunar surface is likely not a result of MB volcanism but is instead mainly associated with the combined action of plutonic intrusion, KREEP volcanism and celestial collision; (4) the impact size of the South Pole-Aitken basin is constrained, i.e., the basin has been excavated through the whole crust to exhume a vast majority of lower-crustal material and a very limited mantle components to the lunar surface.

Geochemistry of sapphirine-apatite-calcite-bearing gabbroic dykes from the Finero Phlogopite Peridotite (Ivrea-Verbano Zone): evidence for multistage interaction with the ambient peridotite

NASA Astrophysics Data System (ADS)

Tommaso, Giovanardi; Alberto, Zanetti; Maurizio, Mazzucchelli; Tomoaki, Morishita; Antonio, Langone

2016-04-01

The Finero Phlogopite-Peridotite (FPP) is a mantle unit outcropping in the northernmost tip of the Ivrea-Verbano Zone (IVZ, Southern Alps). It shows a virtually complete recrystallization due to pervasive to channelled melt migration. The pervasive metasomatism formed a main lithologic association constituted by phlogopite harzburgites associated to phlogopite pyroxenites (mainly olivine-websterites, websterites and orthopyroxenites). These lithologies are also rich in amphibole and do not show significant chemical gradients among them (Zanetti et al., 1999). The channelled migration stages formed dunite bodies, which sometimes contain stratiform chromitites and, more rarely, pyroxenite layers similar to those associated to phlogopite harzburgite. The FPP also shows a discrete number of other, subordinate rock-types, which are characterised by the presence of apatite usually associated to carbonates (i.e. calcite or dolomite) and exhibit marked modal and chemical gradients with respect to the host phlogopite harzburgite. Examples of these lithologies are apatite-dolomite-bearing wehrlites and harzburgites (e.g. Zanetti et al. 1999; Morishita et al., 2008), apatite-calcite zircon-syenites and hornblendites. Ar-Ar amphibole analysis and U-Pb zircon and apatite data return Triassic ages for these rocks, which have been considered to document the time of melt/fluid injection. Notwithstanding the apparent mineralogical and chemical differences with the main lithologic sequences, apatite-carbonates-bearing rocks have been frequently interpreted as cogenetic to phlogopite harzburgites. To debate the petrogenesis of these rocks, a detailed field, petrological and geochemical investigation has been carried out on a swarm of apatite-calcite-bearing gabbroic veins that randomly cut the main lithologic association. Preliminary investigation evidenced as these veins show complex metasomatic haloes and a symmetric internal layering, characterised by crystallisation of magmatic sapphirine (Giovanardi et al., 2013). The mineral assemblage of the veins is dominated by titanian pargasite towards the host peridotite and by plagioclase at the vein centre. The veins also present phlogopite and spinel. Field and petrographic evidence, major and trace element data and the O isotopic composition of such gabbroic veins indicate that they formed at shallow mantle conditions by multistage fractional crystallisation of a migrating melt unrelated to those forming phlogopite harzburgites. Besides, local strong enrichments in LILE, LREE and 18O in vein minerals confirm that such melt was deeply modified by interaction with the host phlogopite peridotite. The genetic relationships with other intrusive events recorded by the FPP and the associated crustal sequence will be addressed with the aim of placing new constraints on the petrologic and geodynamic evolution of the IVZ. Giovanardi, T., Morishita, T., Zanetti, A., Mazzucchelli, M., Vannucci, R. (2013). Igneous sapphirine as a product of melt-peridotite interactions in the Finero Phlogopite-Peridotite Massif, Western Italian Alps. European Journal of Mineralogy 25, 17-31. Morishita, T., Hattori, K.H., Terada, K., Matsumoto, T., Yamamoto, K., Takebe, M., Ishida, Y., Tamura, A., Arai, S. (2008). Geochemistry of apatite-rich layers in the Finero phlogopite-peridotite massif (Italian Western Alps) and ion microprobe dating of apatite. Chemical Geology 251, 99-111. Zanetti, A., Mazzucchelli, M., Rivalenti, G., Vannucci, R. (1999). The Finero phlogopite-peridotite massif: an example of subduction-related metasomatism. Contributions to Mineralogy and Petrology 134, 107-122.

Regional Geological Mapping in the Graham Land of Antarctic Peninsula Using LANDSAT-8 Remote Sensing Data

NASA Astrophysics Data System (ADS)

Pour, A. B.; Hashim, M.; Park, Y.

2017-10-01

Geological investigations in Antarctica confront many difficulties due to its remoteness and extreme environmental conditions. In this study, the applications of Landsat-8 data were investigated to extract geological information for lithological and alteration mineral mapping in poorly exposed lithologies in inaccessible domains such in Antarctica. The north-eastern Graham Land, Antarctic Peninsula (AP) was selected in this study to conduct a satellite-based remote sensing mapping technique. Continuum Removal (CR) spectral mapping tool and Independent Components Analysis (ICA) were applied to Landsat-8 spectral bands to map poorly exposed lithologies at regional scale. Pixels composed of distinctive absorption features of alteration mineral assemblages associated with poorly exposed lithological units were detected by applying CR mapping tool to VNIR and SWIR bands of Landsat-8.Pixels related to Si-O bond emission minima features were identified using CR mapping tool to TIR bands in poorly mapped andunmapped zones in north-eastern Graham Land at regional scale. Anomaly pixels in the ICA image maps related to spectral featuresof Al-O-H, Fe, Mg-O-H and CO3 groups and well-constrained lithological attributions from felsic to mafic rocks were detectedusing VNIR, SWIR and TIR datasets of Landsat-8. The approach used in this study performed very well for lithological andalteration mineral mapping with little available geological data or without prior information of the study region.

Lithological architecture and petrography of the Mako Birimian greenstone belt, Kédougou-Kéniéba Inlier, eastern Senegal

NASA Astrophysics Data System (ADS)

Dabo, Moussa; Aïfa, Tahar; Gning, Ibrahima; Faye, Malick; Ba, Mamadou Fallou; Ngom, Papa Malick

2017-07-01

The new lithological and petrographic data obtained in the Mako sector are analyzed in the light of the geochemical data available in the literature. It consists of ultramaic, mafic rocks of tholeiitic affinities associated with intermediate and felsic rocks of calc-alkaline affinities and with intercalations of sedimentary rocks. The whole unit is intruded by Eburnean granitoids and affected by a greenschist to amphibolite facies metamorphism related to a high grade hydrothermalism. It consists of: (i) ultramafic rocks composed of a fractional crystallization succession of lherzolites, wehrlites and pyroxenites with mafic rock inclusions; (ii) layered, isotropic and pegmatitic metagabbros which gradually pass to metabasalts occur at the top; (iii) massive and in pillow metabasalts with locally tapered vesicles, completely or partially filled with quartzo-feldspathic minerals; (iv) quarzites locally overlying the mafic rocks and thus forming the top of the lower unit. This ultramafic-mafic lower unit presents a tholeiitic affinity near to the OIB or N-MORB. It represents the Mako Ophiolitic Complex (MOC), a lithospheric fragment of Birimian lithospheric crust. The upper unit is a mixed volcanic complex arranged in the tectonic corridors. From bottom to top it comprises the following: (i) andesitic, and (ii) rhyodacitic and rhyolitic lava flows and tuffs, respectively. They present a calc-alkaline affinity of the active margins. Three generations of Eburnean granitoids are recognized: (i) early (2215-2160 Ma); (ii) syn-tectonics (2150-2100 Ma) and post-tectonics (2090-2040 Ma). The lithological succession, geochemical and metamorphic characteristics of these units point to an ophiolitic supra-subduction zone.

HCMM: Soil moisture in relation to geologic structure and lithology, northern California. [Sacremento Valley

NASA Technical Reports Server (NTRS)

Rich, E. I. (Principal Investigator)

1979-01-01

The author has identified the following significant results. A preliminary analysis of the HCMM imagery of the project area indicated that locally some differentiation of lithologic units within the Northern Coast Range may be possible. Of significance, however, was a thermally cool linear area that appeared on the 30 May 1978 Nite-IR. This linear feature seemed to coincide with the Bear Mt. Fault and with the axis of the Chico Monocline along the eastern margin of the Sacramento Valley.

Fractures system within Qusaiba shale outcrop and its relationship to the lithological properties, Qasim area, Central Saudi Arabia

NASA Astrophysics Data System (ADS)

Ibrahim, Mohamed I. M.; Hariri, Mustafa M.; Abdullatif, Osman M.; Makkawi, Mohammad H.; Elzain, Hussam

2017-09-01

The basal Qusaiba hot shale member of Qalibah Formation is considered to be an important source rock in the Paleozoic petroleum system of Saudi Arabia and an exploration target for tight shale as one of the Unconventional resources of petroleum. This work has been carried out to understand the fractures network of Qusaiba shale member in outcrops located to the west of Qusayba' village in Al-Qasim area, Central Saudi Arabia. The main objective of this study is to understand the distribution of natural fractures over different lithological units. Description data sheets were used for the detailed lithological description of Qusaiba shale member on two outcrops. Spot-7 and Landsat ETM+ satellite images were used for lineament mapping and analyses on a regional scale in a GIS environment. Fractures characterization in outcrop-scale was conducted by using linear scanline method. Qusaiba shale member in the study area consists of 5 main lithofacies, divided based on their sedimentary structures and petrographical properties, from base to top in the outcrops, the lithofacies are; fissile shale, very fine-grained micaceous siltstone, bioturbated mudstone, very fine to fine-grained hummocky cross-stratified sandstone, and fine to medium-grained low/high angle cross-stratified sandstone lithofacies. Lineaments interpretation of the Spot-7 and Landsat ETM+ satellite images showed two major directions in the study area; 320° that could be related to Najd fault system and 20° that could be related to the extensional activities which took place after Amar collision. Fractures are much denser in the fissile shale and mudstone lithofacies than sandstones lithofacies, and average spacing is smaller in the fissile shale and mudstone lithofacies than sandstones lithofacies. Lineaments and large-scale fractures are Non-Stratabound fractures and they deal with the area as one big mechanical unit, but small-scale fractures are Stratabound fractures that propose different mechanical units within Qusaiba shale member in the study area. The fractures network in the study area has a wide range of properties related to fractures density, length, spacing, height, and termination degree. The conceptual multi-scale model divides the fractures in the study area into 4 orders depending on the available data that have been observed from satellite images and field. The multi-scale fractures model that was generated in this study could help to understand the distribution of stratigraphically controlled fractures when integrated with flow simulation models. Overall, this work could have a significant contribution to tight shale exploration plans in the subsurface by providing some knowledge about the fractures mechanical behavior of the lower part of Qusaiba shale member of Qalibah Formation.

Mapping urban geology of the city of Girona, Catalonia

NASA Astrophysics Data System (ADS)

Vilà, Miquel; Torrades, Pau; Pi, Roser; Monleon, Ona

2016-04-01

A detailed and systematic geological characterization of the urban area of Girona has been conducted under the project '1:5000 scale Urban geological map of Catalonia' of the Catalan Geological Survey (Institut Cartogràfic i Geològic de Catalunya). The results of this characterization are organized into: i) a geological information system that includes all the information acquired; ii) a stratigraphic model focused on identification, characterization and correlation of the geological materials and structures present in the area and; iii) a detailed geological map that represents a synthesis of all the collected information. The mapping project integrates in a GIS environment pre-existing cartographic documentation (geological and topographical), core data from compiled boreholes, descriptions of geological outcrops within the urban network and neighbouring areas, physico-chemical characterisation of representative samples of geological materials, detailed geological mapping of Quaternary sediments, subsurface bedrock and artificial deposits and, 3D modelling of the main geological surfaces. The stratigraphic model is structured in a system of geological units that from a chronostratigrafic point of view are structured in Palaeozoic, Paleogene, Neogene, Quaternary and Anthropocene. The description of the geological units is guided by a systematic procedure. It includes the main lithological and structural features of the units that constitute the geological substratum and represents the conceptual base of the 1:5000 urban geological map of the Girona metropolitan area, which is organized into 6 map sheets. These map sheets are composed by a principal map, geological cross sections and, several complementary maps, charts and tables. Regardless of the geological map units, the principal map also represents the main artificial deposits, features related to geohistorical processes, contours of outcrop areas, information obtained in stations, borehole data, and contour lines of the top of the pre-Quaternary basement surface. The most representative complementary maps are the quaternary map, the subsurface bedrock map and the isopach map of thickness of superficial deposits (Quaternary and anthropogenic). The map sheets also include charts and tables of relevant physic-chemical parameters of the geological materials, harmonized downhole lithological columns from selected boreholes, stratigraphic columns, and, photographs and figures illustrating the geology of the mapped area and how urbanization has changed the natural environment. The development of systematic urban geological mapping projects, such as the example of Girona's case, which provides valuable resources to address targeted studies related to urban planning, geoengineering works, soil pollution and other important environmental issues that society should deal with in the future.

[Lithology feature extraction of CASI hyperspectral data based on fractal signal algorithm].

PubMed

Tang, Chao; Chen, Jian-Ping; Cui, Jing; Wen, Bo-Tao

2014-05-01

Hyperspectral data is characterized by combination of image and spectrum and large data volume dimension reduction is the main research direction. Band selection and feature extraction is the primary method used for this objective. In the present article, the authors tested methods applied for the lithology feature extraction from hyperspectral data. Based on the self-similarity of hyperspectral data, the authors explored the application of fractal algorithm to lithology feature extraction from CASI hyperspectral data. The "carpet method" was corrected and then applied to calculate the fractal value of every pixel in the hyperspectral data. The results show that fractal information highlights the exposed bedrock lithology better than the original hyperspectral data The fractal signal and characterized scale are influenced by the spectral curve shape, the initial scale selection and iteration step. At present, research on the fractal signal of spectral curve is rare, implying the necessity of further quantitative analysis and investigation of its physical implications.

Lithologic and hydrologic controls of mixed alluvial-bedrock channels in flood-prone fluvial systems: bankfull and macrochannels in the Llano River watershed, central Texas, USA

USGS Publications Warehouse

Heitmuller, Frank T.; Hudson, Paul F.; Asquith, William H.

2015-01-01

The rural and unregulated Llano River watershed located in central Texas, USA, has a highly variable flow regime and a wide range of instantaneous peak flows. Abrupt transitions in surface lithology exist along the main-stem channel course. Both of these characteristics afford an opportunity to examine hydrologic, lithologic, and sedimentary controls on downstream changes in channel morphology. Field surveys of channel topography and boundary composition are coupled with sediment analyses, hydraulic computations, flood-frequency analyses, and geographic information system mapping to discern controls on channel geometry (profile, pattern, and shape) and dimensions along the mixed alluvial-bedrock Llano River and key tributaries. Four categories of channel classification in a downstream direction include: (i) uppermost ephemeral reaches, (ii) straight or sinuous gravel-bed channels in Cretaceous carbonate sedimentary zones, (iii) straight or sinuous gravel-bed or bedrock channels in Paleozoic sedimentary zones, and (iv) straight, braided, or multithread mixed alluvial–bedrock channels with sandy beds in Precambrian igneous and metamorphic zones. Principal findings include: (i) a nearly linear channel profile attributed to resistant bedrock incision checkpoints; (ii) statistically significant correlations of both alluvial sinuosity and valley confinement to relatively high f (mean depth) hydraulic geometry values; (iii) relatively high b (width) hydraulic geometry values in partly confined settings with sinuous channels upstream from a prominent incision checkpoint; (iv) different functional flow categories including frequently occurring events (< 1.5-year return periods) that mobilize channel-bed material and less frequent events that determine bankfull channel (1.5- to 3-year return periods) and macrochannel (10- to 40-year return periods) dimensions; (v) macrochannels with high f values (most ≤ 0.45) that develop at sites with unit stream power values in excess of 200 watts per square meter (W/m2); and (vi) downstream convergence of hydraulic geometry exponents for bankfull and macrochannels, explained by co-increases of flood magnitude and noncohesive sandy sediments that collectively minimize development of alluvial bankfull indicators. Collectively, these findings indicate that mixed alluvial–bedrock channels exhibit first-order lithologic controls (lithologic resistance and valley confinement) of channel geometry, second-order hydrologic (flow regime) control of channel dimensions, and third-order sedimentary controls that exert subsidiary influence on channel shape and bed configuration.

Hyperspectral analysis of the ultramafic complex and adjacent lithologies at Mordor, NT, Australia

USGS Publications Warehouse

Rowan, L.C.; Simpson, C.J.; Mars, J.C.

2004-01-01

The Mordor Complex consists of a series of potassic ultramafic rocks which were intruded into Proterozoic felsic gneisses and amphibolite and are overlain by quartzite and unconsolidated deposits. In situ and laboratory 0.4 to 2.5 ??m reflectance spectra show Al-OH absorption features caused by absorption in muscovite, kaolinite, and illite/smectite in syenite, granitic gneiss, quartzite and unconsolidated sedimentary deposits, and Fe,Mg-OH features due to phlogopite, biotite, epidote, and hornblende in the mafic and ultramafic rocks. Ferrous-iron absorption positioned near 1.05 ??m is most intense in peridotite reflectance spectra. Ferric-iron absorption is intense in most of the felsic lithologies. HyMap data were recorded in 126 narrow bands from 0.43 to 2.5 ??m along a 7-km-wide swath with approximately 6-m spatial resolution. Correction of the data to spectral reflectance was accomplished by reference to in situ measurements of an extensive, alluvial plain. Spectral classes for matched filter processing were selected by using the pixel purity index procedure and analysis of in situ and laboratory spectra. Considering the spatial distribution of the resulting 14 classes, some classes were combined, which produced eight classes characterized by Al-OH absorption features, and three Fe,Mg-OH absorption-feature classes. Comparison of the distribution of these 11 spectral classes to a generalized lithologic map of the study area shows that the spectral distinction among the eight Al-OH classes is related to variations in primary lithology, weathering products, and vegetation density. Quartzite is represented in three classes, syenite corresponds to a single scattered class, quartz-muscovite-biotite schist defines a single very coherent class, and unconsolidated sediments are portrayed in four classes. The three mafic-ultramafic classes are distinguished on the basis of generally intense Fe,Mg-OH and ferrous-iron absorption features. A single class represents the main Mordor ultramafic mass. Epidote-bearing rocks define another class, which corresponds to biotite gneiss and, in the southern part of the area, to fracture zones. The third class, which exhibits Al-OH, as well as Fe,Mg-OH features, represents hornblende gneiss and other mafic gneisses. These results indicate the importance of analyzing the VNIR and SWIR spectral shape and albedo, as well as analyzing specific spectral features, for mapping lithologic units in this weathered terrain. ?? 2004 Elsevier Inc. All rights reserved.

Mineralogy and petrography of C asteroid regolith: The Sutter's Mill CM meteorite

NASA Astrophysics Data System (ADS)

Zolensky, Michael; Mikouchi, Takashi; Fries, Marc; Bodnar, Robert; Jenniskens, Peter; Yin, Qing-zhu; Hagiya, Kenji; Ohsumi, Kazumasa; Komatsu, Mutsumi; Colbert, Matthew; Hanna, Romy; Maisano, Jessie; Ketcham, Richard; Kebukawa, Yoko; Nakamura, Tomoki; Matsuoka, Moe; Sasaki, Sho; Tsuchiyama, Akira; Gounelle, Matthieu; Le, Loan; Martinez, James; Ross, Kent; Rahman, Zia

2014-11-01

Based upon our characterization of three separate stones by electron and X-ray beam analyses, computed X-ray microtomography, Raman microspectrometry, and visible-IR spectrometry, Sutter's Mill is a unique regolith breccia consisting mainly of various CM lithologies. Most samples resemble existing available CM2 chondrites, consisting of chondrules and calcium-aluminum-rich inclusion (CAI) set within phyllosilicate-dominated matrix (mainly serpentine), pyrrhotite, pentlandite, tochilinite, and variable amounts of Ca-Mg-Fe carbonates. Some lithologies have witnessed sufficient thermal metamorphism to transform phyllosilicates into fine-grained olivine, tochilinite into troilite, and destroy carbonates. One finely comminuted lithology contains xenolithic materials (enstatite, Fe-Cr phosphides) suggesting impact of a reduced asteroid (E or M class) onto the main Sutter's Mill parent asteroid, which was probably a C class asteroid. One can use Sutter's Mill to help predict what will be found on the surfaces of C class asteroids such as Ceres and the target asteroids of the OSIRIS-REx and Hayabusa 2 sample return missions (which will visit predominantly primitive asteroids). C class asteroid regolith may well contain a mixture of hydrated and thermally dehydrated indigenous materials as well as a significant admixture of exogenous material would be essential to the successful interpretation of mineralogical and bulk compositional data.

Laboratory measurements of the seismic velocities and other petrophysical properties of the Outokumpu deep drill core samples, eastern Finland

NASA Astrophysics Data System (ADS)

Elbra, Tiiu; Karlqvist, Ronnie; Lassila, Ilkka; Høgström, Edward; Pesonen, Lauri J.

2011-01-01

Petrophysical, in particular seismic velocity, measurements of the Outokumpu deep drill core (depth 2.5 km) have been carried out to characterize the geophysical nature of the Paleoproterozoic crustal section of eastern Finland and to find lithological and geophysical interpretations to the distinct crustal reflectors as observed in seismic surveys. The results show that different lithological units can be identified based on the petrophysical data. The density of the samples remained nearly constant throughout the drilled section. Only diopside-tremolite skarns and black schists exhibit higher densities. The samples are dominated by the paramagnetic behaviour with occasional ferromagnetic signature caused by serpentinitic rocks. Large variations in seismic velocities, both at ambient pressure and under in situ crustal conditions are observed. The porosity of the samples, which is extremely low, is either intrinsic by nature or caused by decompaction related to fracturing during the core retrieval. It is noteworthy that these microfractures have dramatically lowered the VP and VS values. From the measured velocities and density data we have calculated the seismic impedances, Young's modulus and Poisson's ratios for the lithological units of the Outokumpu section and from these data the reflection coefficients for the major lithological boundaries, evident in the surveyed section, were determined. The data show that the strong and distinct reflections visible in wide-angle seismic surveys are caused by interfaces between diopside-tremolite skarn and either serpentinites, mica schist or black schist.

Nationwide lithological interpretation of cone penetration tests using neural networks

NASA Astrophysics Data System (ADS)

van Maanen, Peter-Paul; Schokker, Jeroen; Harting, Ronald; de Bruijn, Renée

2017-04-01

The Geological Survey of the Netherlands (GSN) systematically produces 3D stochastic geological models of the Dutch subsurface. These voxel models are regarded essential in answering subsurface-related questions on, for example, aggregate resource potential, groundwater flow, land subsidence hazard and the planning and realization of large-scale infrastructural works. GeoTOP is the most recent and detailed generation of 3D voxel models. This model describes 3D stratigraphical and lithological variability up to a depth of 50 m using voxels of 100 × 100 × 0.5 m. Currently, visually described borehole samples are the primary input of these large-scale 3D geological models, both when modeling architecture and composition. Although tens of thousands of cone penetration tests (CPTs) are performed each year, mainly in the reconnaissance phase of construction activities, these data are hardly used as geological model input. There are many reasons why it is of interest to utilize CPT data for geological and lithological modeling of the Dutch subsurface, such as: 1) CPTs are more abundant than borehole descriptions, 2) CPTs are cheaper and easier to gather, and 3) CPT data are more quantitative and uniform than visual sample descriptions. This study uses CPTs and the lithological descriptions of associated nearby undisturbed drilling cores collected by the GSN to establish a nationwide reference dataset for physical and chemical properties of the shallow subsurface. The 167 CPT-core pairs were collected at 160 locations situated in the North, West and South of the Netherlands. These locations were chosen to cover the full extent of geological units and lithological composition in the upper 30 to 40 m of the subsurface in these areas. The distance between the CPT location and associated borehole is small, varying between 0 and 30 m, with an average of 6 m. For each 2 cm CPT interval the data was automatically annotated with the lithoclass from the associated core using a lithological classification script that is also used in GeoTOP to classify the visual sample descriptions. Based on this data a three-layer feedforward neural network was trained containing 5 different inputs: cone resistance, friction ratio, coordinates x and y, and interval depth z. Previous training attempts showed an increased performance when using additional inputs such as pore water pressure, but since these variables are not measured in the majority of CPTs, these were left out in the training procedure. The Newton conjugate-gradient algorithm was applied to train the network. 20-Fold cross-validation yielded 20 different trained nets and independent performance outcomes. Significant performance increase was found as compared to performances of conventional lithological classification charts. A similar neural network was then applied to new CPT data from a pilot area in the city of Rotterdam. This area has a limited number of visual sample descriptions and therefore, additional lithological information of the subsurface is desirable. The results of an evaluation of the neural network's outcomes in this area by geological experts are positive, which paves the way for future nationwide application of this method.

Comparison of Different Machine Learning Algorithms for Lithological Mapping Using Remote Sensing Data and Morphological Features: A Case Study in Kurdistan Region, NE Iraq

NASA Astrophysics Data System (ADS)

Othman, Arsalan; Gloaguen, Richard

2015-04-01

Topographic effects and complex vegetation cover hinder lithology classification in mountain regions based not only in field, but also in reflectance remote sensing data. The area of interest "Bardi-Zard" is located in the NE of Iraq. It is part of the Zagros orogenic belt, where seven lithological units outcrop and is known for its chromite deposit. The aim of this study is to compare three machine learning algorithms (MLAs): Maximum Likelihood (ML), Support Vector Machines (SVM), and Random Forest (RF) in the context of a supervised lithology classification task using Advanced Space-borne Thermal Emission and Reflection radiometer (ASTER) satellite, its derived, spatial information (spatial coordinates) and geomorphic data. We emphasize the enhancement in remote sensing lithological mapping accuracy that arises from the integration of geomorphic features and spatial information (spatial coordinates) in classifications. This study identifies that RF is better than ML and SVM algorithms in almost the sixteen combination datasets, which were tested. The overall accuracy of the best dataset combination with the RF map for the all seven classes reach ~80% and the producer and user's accuracies are ~73.91% and 76.09% respectively while the kappa coefficient is ~0.76. TPI is more effective with SVM algorithm than an RF algorithm. This paper demonstrates that adding geomorphic indices such as TPI and spatial information in the dataset increases the lithological classification accuracy.

Three-Dimensional Geologic Model of Complex Fault Structures in the Upper Seco Creek Area, Medina and Uvalde Counties, South-Central Texas

USGS Publications Warehouse

Pantea, Michael P.; Cole, James C.; Smith, Bruce D.; Faith, Jason R.; Blome, Charles D.; Smith, David V.

2008-01-01

This multimedia report shows and describes digital three-dimensional faulted geologic surfaces and volumes of the lithologic units of the Edwards aquifer in the upper Seco Creek area of Medina and Uvalde Counties in south-central Texas. This geologic framework model was produced using (1) geologic maps and interpretations of depositional environments and paleogeography; (2) lithologic descriptions, interpretations, and geophysical logs from 31 drill holes; (3) rock core and detailed lithologic descriptions from one drill hole; (4) helicopter electromagnetic geophysical data; and (5) known major and minor faults in the study area. These faults were used because of their individual and collective effects on the continuity of the aquifer-forming units in the Edwards Group. Data and information were compared and validated with each other and reflect the complex relationships of structures in the Seco Creek area of the Balcones fault zone. This geologic framework model can be used as a tool to visually explore and study geologic structures within the Seco Creek area of the Balcones fault zone and to show the connectivity of hydrologic units of high and low permeability between and across faults. The software can be used to display other data and information, such as drill-hole data, on this geologic framework model in three-dimensional space.

Patterns of landscape form in the upper Rhône basin, Central Swiss Alps, predominantly show lithologic controls despite multiple glaciations and variations in rock uplift rates

NASA Astrophysics Data System (ADS)

Stutenbecker, L. A.; Costa, A.; Schlunegger, F.

2015-10-01

The development of topography is mainly dependent on the interplay of uplift and erosion, which are in term controlled by various factors including climate, glaciers, lithology, seismic activity and short-term variables such as anthropogenic impact. While most studies have focused on the role of tectonics and climate on the landscape form and underlying processes, less attention has been paid on exploring the controls of lithology on erosion. The Central European Alps are characterized by a large spatial variability in exposed lithologies and as such offer an ideal laboratory to investigate the lithological controls on erosion and landscape form. Here, we focus on the ca. 5400 km2-large upper Rhône basin situated in the Central Swiss Alps to explore how the lithological architecture of the bedrock conditions the Alpine landscape. To this extent, we extract geomorphological parameters along the channels of ca. 50 tributary basins, whose catchments are located in either granitic basement rocks (External massifs), oceanic meta-sedimentary and ophiolitic rocks (Penninic nappes) or fine-grained continental-margin sediments (Helvetic nappes). The analysis of longitudinal river profiles show that all tributary rivers within the Rhône basin are in topographic transient state as testified by mainly convex or concave-convex longitudinal stream channel profiles with several knickpoints of either tectonic or glacial origin. In addition, although the entire Rhône basin shows a strong glacial inheritance (and is still partly glaciated) and some of the highest uplift rates recently measured in the Alps, the river network has responded differently to those perturbations as revealed by the morphometric data. In particular, tributary basins in the Helvetic nappes are the most equilibrated (concave river profiles, overall lower elevations, less steep slope gradients and lowest hypsometric integrals), while the tributaries located in the External massifs are least equilibrated, where streams yield strong convex long profiles, and where the tributary basins have the highest hypsometric integral and reveal the steepest hillslopes. We interpret this pattern to reflect differences in response times of the fluvial erosion in tributary streams towards glacial and tectonic perturbations, where the corresponding lengths strongly depend on the lithology and therefore on the bedrock erodibility.

Rim Structure, Stratigraphy, and Aqueous Alteration Exposures Along Opportunity Rover's Traverse of the Noachian Endeavour Crater

NASA Technical Reports Server (NTRS)

Crumpler, L.S.; Arvidson, R. E.; Golombek, M.; Grant, J. A.; Jolliff, B. L.; Mittlefehldt, D. W.

2017-01-01

The Mars Exploration Rover Opportunity has traversed 10.2 kilometers along segments of the west rim of the 22-kilometer-diameter Noachian Endeavour impact crater as of sol 4608 (01/09/17). The stratigraphy, attitude of units, lithology, and degradation state of bedrock outcrops exposed on the crater rim have been examined in situ and placed in geologic context. Structures within the rim and differences in physical properties of the identified lithologies have played important roles in localizing outcrops bearing evidence of aqueous alteration.

Use of induced polarization to characterize the hydrogeologic framework of the zone of surface‐water/groundwater exchange at the Hanford 300 Area, WA

USGS Publications Warehouse

Slater, Lee; Ntarlagiannis, Dimitrios; Day-Lewis, Frederick D.; Mwakanyamale, Kisa; Lane, John W.; Ward, Andy; Versteeg, Roelof J.

2010-01-01

An extensive continuous waterborne electrical imaging (CWEI) survey was conducted along the Columbia River corridor adjacent to the U.S. Department of Energy (DOE) Hanford 300 Area, WA, in order to improve the conceptual model for exchange between surface water and U‐contaminated groundwater. The primary objective was to determine spatial variability in the depth to the Hanford‐Ringold (H‐R) contact, an important lithologic boundary that limits vertical transport of groundwater along the river corridor. Resistivity and induced polarization (IP) measurements were performed along six survey lines parallel to the shore (each greater than 2.5 km in length), with a measurement recorded every 0.5–3.0 m depending on survey speed, resulting in approximately 65,000 measurements. The H‐R contact was clearly resolved in images of the normalized chargeability along the river corridor due to the large contrast in surface area (hence polarizability) of the granular material between the two lithologic units. Cross sections of the lithologic structure along the river corridor reveal a large variation in the thickness of the overlying Hanford unit (the aquifer through which contaminated groundwater discharges to the river) and clearly identify locations along the river corridor where the underlying Ringold unit is exposed to the riverbed. Knowing the distribution of the Hanford and Ringold units along the river corridor substantially improves the conceptual model for the hydrogeologic framework regulating U exchange between groundwater and Columbia River water relative to current models based on projections of data from boreholes on land into the river.

Blueschist preservation in a retrograded, high-pressure, low-temperature metamorphic terrane, Tinos, Greece: Implications for fluid flow paths in subduction zones

NASA Astrophysics Data System (ADS)

Breeding, Christopher M.; Ague, Jay J.; BröCker, Michael; Bolton, Edward W.

2003-01-01

The preservation of high-pressure, low-temperature (HP-LT) mineral assemblages adjacent to marble unit contacts on the Cycladic island of Tinos in Greece was investigated using a new type of digital outcrop mapping and numerical modeling of metamorphic fluid infiltration. Mineral assemblage distributions in a large blueschist outcrop, adjacent to the basal contact of a 150-meter thick marble horizon, were mapped at centimeter-scale resolution onto digital photographs using a belt-worn computer and graphics editing software. Digital mapping reveals that while most HP-LT rocks in the outcrop were pervasively retrograded to greenschist facies, the marble-blueschist contact zone underwent an even more intense retrogression. Preservation of HP-LT mineral assemblages was mainly restricted to a 10-15 meter zone (or enclave) adjacent to the intensely retrograded lithologic contact. The degree and distribution of the retrograde overprint suggests that pervasively infiltrating fluids were channelized into the marble-blueschist contact and associated veins and flowed around the preserved HP-LT enclave. Numerical modeling of Darcian flow, based on the field observations, suggests that near the marble horizon, deflections in fluid flow paths caused by flow channelization along the high-permeability marble-blueschist contact zone likely resulted in very large fluid fluxes along the lithologic contact and significantly smaller fluxes (as much as 8 times smaller than the input flux) within the narrow, low-flux regions where HP-LT minerals were preserved adjacent to the contact. Our results indicate that lithologic contacts are important conduits for metamorphic fluid flow in subduction zones. Channelization of retrograde fluids into these discrete flow conduits played a critical role in the preservation of HP-LT assemblages.

Diverse Lithologies on a Crater Floor

NASA Image and Video Library

2018-04-16

This image from NASA's Mars Reconnaissance Orbiter (MRO) shows bedrock units with diverse colors indicating different mineral concentrations. More information is available at https://photojournal.jpl.nasa.gov/catalog/PIA22434

Lithological and Surface Geometry Joint Inversions Using Multi-Objective Global Optimization Methods

NASA Astrophysics Data System (ADS)

Lelièvre, Peter; Bijani, Rodrigo; Farquharson, Colin

2016-04-01

Geologists' interpretations about the Earth typically involve distinct rock units with contacts (interfaces) between them. In contrast, standard minimum-structure geophysical inversions are performed on meshes of space-filling cells (typically prisms or tetrahedra) and recover smoothly varying physical property distributions that are inconsistent with typical geological interpretations. There are several approaches through which mesh-based minimum-structure geophysical inversion can help recover models with some of the desired characteristics. However, a more effective strategy may be to consider two fundamentally different types of inversions: lithological and surface geometry inversions. A major advantage of these two inversion approaches is that joint inversion of multiple types of geophysical data is greatly simplified. In a lithological inversion, the subsurface is discretized into a mesh and each cell contains a particular rock type. A lithological model must be translated to a physical property model before geophysical data simulation. Each lithology may map to discrete property values or there may be some a priori probability density function associated with the mapping. Through this mapping, lithological inverse problems limit the parameter domain and consequently reduce the non-uniqueness from that presented by standard mesh-based inversions that allow physical property values on continuous ranges. Furthermore, joint inversion is greatly simplified because no additional mathematical coupling measure is required in the objective function to link multiple physical property models. In a surface geometry inversion, the model comprises wireframe surfaces representing contacts between rock units. This parameterization is then fully consistent with Earth models built by geologists, which in 3D typically comprise wireframe contact surfaces of tessellated triangles. As for the lithological case, the physical properties of the units lying between the contact surfaces are set to a priori values. The inversion is tasked with calculating the geometry of the contact surfaces instead of some piecewise distribution of properties in a mesh. Again, no coupling measure is required and joint inversion is simplified. Both of these inverse problems involve high nonlinearity and discontinuous or non-obtainable derivatives. They can also involve the existence of multiple minima. Hence, one can not apply the standard descent-based local minimization methods used to solve typical minimum-structure inversions. Instead, we are applying Pareto multi-objective global optimization (PMOGO) methods, which generate a suite of solutions that minimize multiple objectives (e.g. data misfits and regularization terms) in a Pareto-optimal sense. Providing a suite of models, as opposed to a single model that minimizes a weighted sum of objectives, allows a more complete assessment of the possibilities and avoids the often difficult choice of how to weight each objective. While there are definite advantages to PMOGO joint inversion approaches, the methods come with significantly increased computational requirements. We are researching various strategies to ameliorate these computational issues including parallelization and problem dimension reduction.

Characterization of geologic deposits in the vicinity of US Ecology, Amargosa Basin, southern Nevada

USGS Publications Warehouse

Taylor, Emily M.

2010-01-01

Multiple approaches have been applied to better understand the characteristics of geologic units exposed at the surface and buried at depth in the vicinity of US Ecology (USE), a low-level commercial waste site in the northern Amargosa Desert, Nevada. Techniques include surficial geologic mapping and interpretation of the subsurface using borehole data. Dated deposits at depth were used to estimate rates of sediment accumulation. The subsurface lithologies have been modeled in three dimensions. Lithologic cross sections have been created from the three-dimensional model and have been compared to resistivity data at the same location. Where deposits appear offset, a fault was suspected. Global Positioning System elevation transects were measured and trenches were excavated to locate a strand of the Carrara Fault. The presence of the fault helps to better understand the shape of the potentiometric surface. These data will be used to better understand the hydrologic parameters controlling the containment of the waste at US Ecology.Quaternary geologic units exposed at the surface, in the vicinity of US Ecology, are derived from the alluvium shed off the adjacent range front and the Amargosa River. These deposits vary from modern to early Pleistocene in age. At depth, heterogeneous sands and gravel occur. Observed in deep trenches and boreholes, the subsurface deposits are characterized as fining-upward sequence of sediment from 5- to 8-meters thick. No volcanic units or fine-grained playa deposits were described in the boreholes to a depth of 200 meters. Based on Infrared Stimulated Luminescence dated core samples, short-term rates of sediment accumulation (<70,000 years) are an average of 2.7 millimeters per year, however, long-term rates (<3,900,000 years) are orders of magnitude less. Resistivity data, when compared to lithologic cross sections, generally are consistent with lithology grain size and probable soil carbonate accumulations. Surface resistivity displays a fining-upward sequence of sediments at the surface with a soil carbonate imprint. Finally, trenching north of US Ecology successfully exposed offset Quaternary deposits on a splay of the Carrara Fault. Holocene deposits do not appear to be faulted, however, a fault zone does intersect middle and late Pleistocene aged units.

Prediction of acid mine drainage generation potential of various lithologies using static tests: Etili coal mine (NW Turkey) as a case study.

PubMed

Yucel, Deniz Sanliyuksel; Baba, Alper

2016-08-01

The Etili neighborhood in Can County (northwestern Turkey) has large reserves of coal and has been the site of many small- to medium-scale mining operations since the 1980s. Some of these have ceased working while others continue to operate. Once activities cease, the mining facilities and fields are usually abandoned without rehabilitation. The most significant environmental problem is acid mine drainage (AMD). This study was carried out to determine the acid generation potential of various lithological units in the Etili coal mine using static test methods. Seventeen samples were selected from areas with high acidic water concentrations: from different alteration zones belonging to volcanic rocks, from sedimentary rocks, and from coals and mine wastes. Static tests (paste pH, standard acid-base accounting, and net acid generation tests) were performed on these samples. The consistency of the static test results showed that oxidation of sulfide minerals, especially pyrite-which is widely found not only in the alteration zones of volcanic rocks but also in the coals and mine wastes-is the main factor controlling the generation of AMD in this mine. Lack of carbonate minerals in the region also increases the occurrence of AMD.

Geochemical Models of Water-Quality Changes During Aquifer Storage Recovery (ASR) Cycle Tests, Phase 1: Geochemical Models Using Existing Data

DTIC Science & Technology

2006-09-01

Richardson, in review). Figure 1 shows the lithostratigraphic setting for Eocene through Miocene strata, and the occurrence of hydrostratigraphic units of...basal Haw- thorn unit lies unconformably on lithologies informally called “ Eocene limestones,” which consist of Suwannee Limestone, Ocala Limestone

Three-dimensional trend mapping from wire-line logs

USGS Publications Warehouse

Doveton, J.H.; Ke-an, Z.

1985-01-01

Mapping of lithofacies and porosities of stratigraphic units is complicated because these properties vary in three dimensions. The method of moments was proposed by Krumbein and Libby (1957) as a technique to aid in resolving this problem. Moments are easily computed from wireline logs and are simple statistics which summarize vertical variation in a log trace. Combinations of moment maps have proved useful in understanding vertical and lateral changes in lithology of sedimentary rock units. Although moments have meaning both as statistical descriptors and as mechanical properties, they also define polynomial curves which approximate lithologic changes as a function of depth. These polynomials can be fitted by least-squares methods, partitioning major trends in rock properties from finescale fluctuations. Analysis of variance yields the degree of fit of any polynomial and measures the proportion of vertical variability expressed by any moment or combination of moments. In addition, polynomial curves can be differentiated to determine depths at which pronounced expressions of facies occur and to determine the locations of boundaries between major lithologic subdivisions. Moments can be estimated at any location in an area by interpolating from log moments at control wells. A matrix algebra operation then converts moment estimates to coefficients of a polynomial function which describes a continuous curve of lithologic variation with depth. If this procedure is applied to a grid of geographic locations, the result is a model of variability in three dimensions. Resolution of the model is determined largely by number of moments used in its generation. The method is illustrated with an analysis of lithofacies in the Simpson Group of south-central Kansas; the three-dimensional model is shown as cross sections and slice maps. In this study, the gamma-ray log is used as a measure of shaliness of the unit. However, the method is general and can be applied, for example, to suites of neutron, density, or sonic logs to produce three-dimensional models of porosity in reservoir rocks. ?? 1985 Plenum Publishing Corporation.

Chemistry of Stream Sediments and Surface Waters in New England

USGS Publications Warehouse

Robinson, Gilpin R.; Kapo, Katherine E.; Grossman, Jeffrey N.

2004-01-01

Summary -- This online publication portrays regional data for pH, alkalinity, and specific conductance for stream waters and a multi-element geochemical dataset for stream sediments collected in the New England states of Connecticut, Maine, Massachusetts, New Hampshire, Rhode Island, and Vermont. A series of interpolation grid maps portray the chemistry of the stream waters and sediments in relation to bedrock geology, lithology, drainage basins, and urban areas. A series of box plots portray the statistical variation of the chemical data grouped by lithology and other features.

Quantitative lithologic mapping in spectral ratio feature space - Volcanic, sedimentary and metamorphic terrains

NASA Technical Reports Server (NTRS)

Campos-Marquetti, Raul, Jr.; Rockwell, Barnaby

1990-01-01

The nature of spectral lithologic mapping is studied utilizing ratios centered around the wavelength means of TM imagery. Laboratory-derived spectra are analyzed to determine the two-dimensional relationships and distributions visible in spectral ratio feature space. The spectral distributions of various rocks and minerals in ratio feature space are found to be controlled by several spectrally dominant molecules. Three study areas were examined: Rawhide Mining District, Nevada; Manzano Mountains, New Mexico; and the Sevilleta Long Term Ecological Research site in New Mexico. It is shown that, in the comparison of two ratio plots of laboratory reflectance spectra, i.e., 0.66/0.485 micron versus 1.65/2.22 microns with those derived from TM data, several molecules spectrally dominate the reflectance characteristic of surface lithologic units. Utilizing the above ratio combination, two areas are successfully mapped based on their distribution in spectral ratio feature space.

Sedimentology of the Pennsylvanian and Permian Strathearn Formation, Northern Carlin Trend, Nevada; with a section on microfossil controls on the age of the Strathearn Formation

USGS Publications Warehouse

Berger, Vladimir I.; Singer, Donald A.; Theodore, Ted G.; Harris, Anita G.; Stevens, Calvin H.

2001-01-01

Two framework-supported, poorly bedded conglomerate units of the middle Upper Pennsylvanian and middle Lower Permian Strathearn Formation belonging to the overlap assemblage of the Antler orogen are prominent in the northern Carlin trend. These horizons stratigraphically and temporally bracket thrust emplacement of a major allochthonous thrust plate of mainly quartzarenite of the Ordovician Vinini Formation. Lithologic and shape-ratio data from approximately 4,200 pebbles and cobbles at 17 sites as well as biostratigraphic data in the Strathearn, and their geologic implications, are included in this report. Conodont biofacies throughout the Strathearn Formation are normal marine and suggest middle shelf or deeper depositional environments. The conglomerate units roughly are similar in that they contain only chert and quartzarenite pebbles, but they differ in compositional proportions of the two lithologies. The relative proportion of quartzarenite pebbles increases sixfold in the middle Lower Permian upper conglomerate unit versus its content in the middle Upper Pennsylvanian lower unit, whereas chert pebbles predominate in both units. Various roundness categories of chert pebbles in both conglomerate units of the Strathearn show that the equant pebble class (B/A) = 1 clearly is represented strongly even in the subangular category, the lowest roundness categories for the pebbles. Thus, development of equant pebbles cannot be ascribed totally to a rounding process during predeposition transport. The equant character of many pebbles might, in part, be an original feature inherited from pre-erosion rock fractures and (or) bedding that control overall form of the fragments prior to their release to the transport environment. The allochthon of the Coyote thrust has been thrust above the lower conglomerate unit of the Strathearn during a regionally extensive contractional event in the late Paleozoic. The middle Lower Permian upper conglomerate unit, highest unit recognized in the Strathearn Formation, as well as similarly-aged dolomitic siltstone, onlap directly onto quartzarenite that comprises the allochthon of the Coyote thrust. The conglomerate units thus represent submarine fanglomerates whose quartz grains and quartzarenite fragments of variable roundness and shape were derived from a sedimentologically restored largely southeastward advancing late Paleozoic allochthonous lobe of mostly quartzarenite of the Ordovician Vinini Formation. Chert fragments in the conglomerates probably were derived mostly from Devonian Slaven Chert, including a widespread thick melange unit of the Slaven in the footwall of the Coyote thrust. Some chert pebbles may have been derived from the Ordovician Vinini Formation.

Implementation of magnetic, gravity and resistivity data in identifying groundwater occurrences in El Qaa Plain area, Southern Sinai, Egypt

NASA Astrophysics Data System (ADS)

Selim, El Sayed; Abdel-Raouf, Osama; Mesalam, Mohamed

2016-10-01

El Qaa plain is one of the areas that have been proved to be promising as to its soil and groundwater resources in the southwestern part of Sinai. This study was carried out to study the lateral and vertical variations in the subsurface lithologic properties in El Qaa plain area and delineating the subsurface structure that affecting El Qaa plain depression. Gravity, magnetic data, fifty-one (51) vertical electrical sounding (Ves's) and Digital Elevation Model (DEM) map were used. Two-dimensional density modeling, analytical signal, tilt derivatives, Euler deconvolution techniques and interpretation of the resistivity data were applied on potential data. This study concluded that, El Qaa plain is a NE-SW depression confined by two normal faults and subdivided into five sedimentary units. Rock fragments and boulders derived to the plain from the surrounding highlands are the main components of the first surface unit that characterized by high resistivity values. This layer is overly another unit composed of gravelly sand with thickness ranging between 10 and 140 m. The third unit is composed mainly of sand with intercalations of clay with thickness ranging from 2 to 152 m. A Reefal limestone unit is a fourth unit interpreted from this study. The fifth unit is composed of clay. The water bearing formations in El Qaa Plain area are located principally in the second and the third layers. Finally, the depth to the basement surface ranges from 400 m to more than 1.5 km below sea level. Also, there are many minor structural trends interpreted from this study and affecting the El Qaa plain are striking in N-S, E-W and NE-SW directions.

Preliminary data on boulders at station 6, Apollo 17 landing site

NASA Technical Reports Server (NTRS)

Heiken, G. H.; Butler, P., Jr.; Simonds, C. H.; Phinney, W. C.; Warner, J.; Schmitt, H. H.; Bogard, D. D.; Pearce, W. G.

1973-01-01

A cluster of boulders at Station 6 (Apollo 17 landing site) consists of breccias derived from the North Massif. Three preliminary lithologic units were established, on the basis of photogeologic interpretations; all lithologies identified photogeologically were sampled. Breccia clasts and matrices studied petrographically and chemically fall into two groups by modal mineralogy: (1) low-K Fra Mauro or high basalt composition, consisting of 50-60% modal feldspar, approximately 45% orthopyroxene and 1-7% Fe-Ti oxide; (2) clasts consisting of highland basalt composition, consisting of 70% feldspar, 30% orthopyroxene and olivine and a trace of Fe-Ti oxide.

Origin and development of inland notches in the Classical Karst (NE Adriatic)

NASA Astrophysics Data System (ADS)

Furlani, Stefano; Biolchi, Sara; Devoto, Stefano; Raad, Fadl

2017-04-01

Karst landscapes show morphological features that are different compared to other lithological settings. Inland notches, sub-horizontal indentations extending along carbonate cliffs, are common in the Mediterranean area, in tropical, alpine and semi-arid environments, and develop because of higher erosion rates in correspondence of lithological differences. They can be extended over maximum some hundreds of meters, with an amplitude ranging from 0.5 to 3 m. There is a lack of quantitative data on inland notches with respect to marine notches. We aim at discussing their genesis and evolution by means of morphometric, thermal lithological and micro erosion meter data collected in the Classical Karst area. Rock type is thought to be important in the development of inland notches. Thin sections show that the central part of inland notches are made of more soluble limestones, so lowering rates are higher inside notches rather than outside. Preliminary data on mean lowering rates support the idea that small differences in limestone texture produce differences up to 5 μm/year in lowering rates. For this purpose, their formation is usually associated with limestone beds, although the role and magnitude of karst processes is not completely known. Thermal data show that inland notches are always warmer than the surrounding slopes, with maximum measured differences of 7.5°C. The difference in temperature is higher during the day with respect to the night mainly because of insolation. Data support the hypothesis that inland notches are presently carved in correspondence of even very small differences in lowering rates mainly along bedding planes and, secondly, along geological weakness, such as joints or fractures, as long as lithological differences occur. We assess present understanding of the roles of climate, structural and lithological conditions in inland notches development by new data collected in the Classical Karst area.

Context of ancient aqueous environments on Mars from in situ geologic mapping at Endeavour Crater

USGS Publications Warehouse

Crumpler, L.S.; Arvidson, R. E.; Bell, J.; Clark, B. C.; Cohen, B. A.; Farrand, W. H.; Gellert, Ralf; Golombek, M.; Grant, J. A.; Guinness, E.; Herkenhoff, Kenneth E.; Johnson, J. R.; Jolliff, B.; Ming, D. W.; Mittlefehldt, D. W.; Parker, T.; Rice, J. W.; Squyres, S. W.; Sullivan, R.; Yen, A. S.

2015-01-01

Using the Mars Exploration Rover Opportunity, we have compiled one of the first field geologic maps on Mars while traversing the Noachian terrain along the rim of the 22 km diameter Endeavour Crater (Latitude −2°16′33″, Longitude −5°10′51″). In situ mapping of the petrographic, elemental, structural, and stratigraphic characteristics of outcrops and rocks distinguishes four mappable bedrock lithologic units. Three of these rock units predate the surrounding Burns formation sulfate-rich sandstones and one, the Matijevic Formation, represents conditions on early Mars predating the formation of Endeavour Crater. The stratigraphy assembled from these observations includes several geologic unconformities. The differences in lithologic units across these unconformities record changes in the character and intensity of the Martian aqueous environment over geologic time. Water circulated through fractures in the oldest rocks over periods long enough that texturally and elementally significant alteration occurred in fracture walls. These oldest pre-Endeavour rocks and their network of mineralized and altered fractures were preserved by burial beneath impact ejecta and were subsequently exhumed and exposed. The alteration along joints in the oldest rocks and the mineralized veins and concentrations of trace metals in overlying lithologic units is direct evidence that copious volumes of mineralized and/or hydrothermal fluids circulated through the early Martian crust. The wide range in intensity of structural and chemical modification from outcrop to outcrop along the crater rim shows that the ejecta of large (>8 km in diameter) impact craters is complex. These results imply that geologic complexity is to be anticipated in other areas of Mars where cratering has been a fundamental process in the local and regional geology and mineralogy.

Lithologic controls on AIRSAR signatures of bedrock and alluvium, at Lunar Crater, Nevada

NASA Technical Reports Server (NTRS)

Rivard, Benoit; Diorio, Marc; Budkewitsch, Paul

1995-01-01

Radar backscatter intensity as measured by calibrated synthetic aperture radar (SAR) systems is primarily controlled by three factors: local incidence angle, wavelength-scale roughness, and dielectric permittivity of surface materials. In order to make adequate use of radar observations for geological investigations of surface type, the relationships between lithology and the above characteristics must be adequately understood. In arid terrains weathering signatures (e.g. fracturing, debris grain size and shape, slope characteristics) are controlled to some extent by lithologic characteristics of the parent bedrock. These textural features of outcrops and their associated debris control radar backscatter to varying degrees. The quad-polarization JPL AIRSAR system allows sampling of textures at three distinct wavelength scales: C-band (5.66 cm), L-band (23.98 cm), and P-band (68.13 cm). This paper presents a discussion of AIRSAR data using recent field observations of weathered felsic and basaltic volcanic rock units exposed in the southern part of the Lunar Crater Volcanic Field, in the Pancake Range of central Nevada. The focus is on the relationship of radar backscatter at multiple wavelengths to weathering style and parent bedrock lithology.

Anciet marble quarries in Lesvos island Greece

NASA Astrophysics Data System (ADS)

Mataragkas, M.; Mataragkas, D.

2009-04-01

ANCIENT MARBLE QUARRIES IN LESBOS ISLAND, GREECE Varti- Matarangas M.1 & Matarangas D. 1 Institute of Geological and Mining Exploration (IGME), Olympic Village, Entrance C, ACHARNAE 13677, GREECE myrsini@igme.gr , myrsini@otenet.g r A B S T R A C T Ten ancient marble quarries of Lesbos Island, most of them previously unknown, have been studied, in the frame of the research study on the ancient marble quarries in the Aegean Sea. In the present paper the geological, petrological and morphological features of the aforementioned quarries are examined. Concerning the six ancient quarries located in the areas of Tarti, Agia Paraskevi (Tsaf), Mageiras, Loutra, Latomi (Plomari) and Thermi, the authochthonous neopaleozoic unit constitutes their geological formation, while their hosting lithological formations are the included crystalline limestone lens like beds. In two ancient quarries in the areas Moria and Alyfanta, the geological formation is the authochthonous upper Triassic series and the hosting lithological formation the upper Triassic carbonate sequence, while in the areas of Akrasi-Abeliko and Karyni, the geological formation is the thrust Triassic unit and the lithological hosting formations are the included strongly deformed or not crystalline limestone lenticular beds. Furthermore, the petrographic features were also determined permitting the identification of the building stones that have been used.

Heat and mass transport during a groundwater replenishment trial in a highly heterogeneous aquifer

NASA Astrophysics Data System (ADS)

Seibert, Simone; Prommer, Henning; Siade, Adam; Harris, Brett; Trefry, Mike; Martin, Michael

2014-12-01

Changes in subsurface temperature distribution resulting from the injection of fluids into aquifers may impact physiochemical and microbial processes as well as basin resource management strategies. We have completed a 2 year field trial in a hydrogeologically and geochemically heterogeneous aquifer below Perth, Western Australia in which highly treated wastewater was injected for large-scale groundwater replenishment. During the trial, chloride and temperature data were collected from conventional monitoring wells and by time-lapse temperature logging. We used a joint inversion of these solute tracer and temperature data to parameterize a numerical flow and multispecies transport model and to analyze the solute and heat propagation characteristics that prevailed during the trial. The simulation results illustrate that while solute transport is largely confined to the most permeable lithological units, heat transport was also affected by heat exchange with lithological units that have a much lower hydraulic conductivity. Heat transfer by heat conduction was found to significantly influence the complex temporal and spatial temperature distribution, especially with growing radial distance and in aquifer sequences with a heterogeneous hydraulic conductivity distribution. We attempted to estimate spatially varying thermal transport parameters during the data inversion to illustrate the anticipated correlations of these parameters with lithological heterogeneities, but estimates could not be uniquely determined on the basis of the collected data.

Sm-Nd Age and Nd- and Sr- Isotopic Evidence for the Petrogenesis of Dhofar 378

NASA Technical Reports Server (NTRS)

Nyquist, L. E.; Ikeda, Y.; Shih, C.-Y.; Reese, Y. D.; Nakamura, N.; Takeda, H.

2006-01-01

Dhofar 378 (hereafter Dho 378) is one of the most ferroan lithologies among martian meteorites, resembling the Los Angeles basaltic shergottite in lithology and mineral chemistry, although it is more highly shocked than Los Angeles. All plagioclase (Pl) grains in the original lithology were melted by an intense shock in the range 55-75 GPa. Clinopyroxenes (Cpx) sometimes show mosaic extinction under a microscope showing that they, too, experienced intense shock. Nevertheless, they zone from magnesian cores to ferroan rims, reflecting the original lithology. Cpx grains also often contain exsolution lamellae, showing that the original lithology cooled slowly enough for the lamellae to form. Because all plagioclase grains were melted by the intense shock and subsequently quenched, the main plagioclase component is glass (Pl-glass) rather than maskelynite. Like Los Angeles, but unlike most basaltic shergottites, Dho 378 contains approximately equal modal abundances of Cpx and Pl-glass. The grain sizes of the original minerals were comparatively large (approximately 1 mm). The original plagioclase zoning has been severely modified. Following shock melting, the plagioclase melts crystallized from the outside inward, first forming outer rims of Cpx-Pl intergrowths (approximately 10 micrometers) followed by inner rims (10's to 100 micrometers) of An(sub 40-50) feldspar, and finally Pl-gl cores of compositions An(sub 33-50) with orthoclase compositions up to Or(sub 12).

Mechanisms for landscape evolution: Correlations between topography, lithology, erosion, and rock uplift in the central Nepalese Himalaya

NASA Astrophysics Data System (ADS)

Walsh, L. S.; Martin, A. J.; Ojha, T. P.; Fedenczuk, T.

2009-12-01

To investigate feedbacks between tectonics and erosion in the Himalaya-Tibet orogen we compare high resolution digital topography with detailed geologic maps of the Modi Khola valley in central Nepal. We examine the influence of lithologic contacts and structures on river steepness and concavity. The trace of the Bhanuwa fault, a large normal fault in Greater Himalayan rocks, coincides with the steepest location on the river profile where river steepness (ksn) reaches 884 m0.9. Transitions in ksn also occur at 1) the Romi fault, another normal fault, 2) within the Kuncha formation, 3) within Greater Himalayan rocks at the Formation I - Formation II boundary, and 4) between quartzite- and phyllite-rich parts of the Fagfog Formation. We assess mechanisms for ksn transitions on the Modi Khola by examining the influence of precipitation variability, glacial and landslide dams, tributary junctions, changes in lithology, and rock uplift on the topography. Although changes in lithology and/or landslide dams potentially explain all ksn extrema and transitions, these changes in river steepness consistently occur at normal faults suggesting possible recent motion on some of them. In detail, the Main Central thrust appears not to be the location of a major steepness change. Correlations of ksn with normal faults and lithologic contacts exhibit an important component of the landscape evolution process occurring in central Nepal and potentially other mountain belts.

Lithologic boundaries from gravity and magnetic anomalies over Proterozoic Dalma volcanics

NASA Astrophysics Data System (ADS)

Yadav, Pramod Kumar; Adhikari, P. K.; Srivastava, Shalivahan; Maurya, Ved P.; Tripathi, Anurag; Singh, Shailendra; Singh, Roshan K.; Bage, Ashish K.

2018-03-01

Dalma volcanics (DVs) has intruded the older Singhbhum Group of Metapelites. Despite DVs being rich in mineralisation, its boundaries are not clearly demarcated. Gravity and magnetic surveys have been attempted for mapping the boundaries in DVs. These surveys were made in the northern fringe of the DVs over an area of ˜ 0.70 km2 along 13 parallel lines at 50 m spacing. The data was acquired at ˜ 25 m spacing. The surveys were taken for determination of lithological boundaries, depths and nature of causative source using Euler depth solutions and radially averaged power spectrum (RAPS). Residual anomaly maps of gravity and magnetic intensity show the same trend as that of Bouguer gravity anomaly and total magnetic intensity anomaly map indicating towards shallow sources. The magnetic map in general follows the same pattern as that of gravity anomaly maps. The map shows coincident high gravity and magnetic anomalies. These anomalies together with resistivity signatures confirm that the northern fringe of DVs hosts volcanogenic massive sulphide settings. The Euler depth solution delineated the lateral boundaries and nature of the source. It seems that the source is of spherical nature lying within a depth range of 25-40 m. The obtained lithological (vertical) units from RAPS are between Lower DVs, Upper DVs and Singhbhum Group Metapelites at depths of ˜ 15, ˜ 25 and ˜ 40 m, respectively. The metallogeny is associated with the Upper DVs and the corresponding delineated lithological (vertical) unit is indicative of the top of the ore body. Good agreement is observed with the geological succession from the drilling data and resistivity data. The findings suggest that the northern fringe of DVs could be a preferred target for drilling.

Inverse geothermal modelling applied to Danish sedimentary basins

NASA Astrophysics Data System (ADS)

Poulsen, Søren E.; Balling, Niels; Bording, Thue S.; Mathiesen, Anders; Nielsen, Søren B.

2017-10-01

This paper presents a numerical procedure for predicting subsurface temperatures and heat-flow distribution in 3-D using inverse calibration methodology. The procedure is based on a modified version of the groundwater code MODFLOW by taking advantage of the mathematical similarity between confined groundwater flow (Darcy's law) and heat conduction (Fourier's law). Thermal conductivity, heat production and exponential porosity-depth relations are specified separately for the individual geological units of the model domain. The steady-state temperature model includes a model-based transient correction for the long-term palaeoclimatic thermal disturbance of the subsurface temperature regime. Variable model parameters are estimated by inversion of measured borehole temperatures with uncertainties reflecting their quality. The procedure facilitates uncertainty estimation for temperature predictions. The modelling procedure is applied to Danish onshore areas containing deep sedimentary basins. A 3-D voxel-based model, with 14 lithological units from surface to 5000 m depth, was built from digital geological maps derived from combined analyses of reflection seismic lines and borehole information. Matrix thermal conductivity of model lithologies was estimated by inversion of all available deep borehole temperature data and applied together with prescribed background heat flow to derive the 3-D subsurface temperature distribution. Modelled temperatures are found to agree very well with observations. The numerical model was utilized for predicting and contouring temperatures at 2000 and 3000 m depths and for two main geothermal reservoir units, the Gassum (Lower Jurassic-Upper Triassic) and Bunter/Skagerrak (Triassic) reservoirs, both currently utilized for geothermal energy production. Temperature gradients to depths of 2000-3000 m are generally around 25-30 °C km-1, locally up to about 35 °C km-1. Large regions have geothermal reservoirs with characteristic temperatures ranging from ca. 40-50 °C, at 1000-1500 m depth, to ca. 80-110 °C, at 2500-3500 m, however, at the deeper parts, most likely, with too low permeability for non-stimulated production.

Geology of the surficial aquifer system, Broward County, Florida; lithologic logs

USGS Publications Warehouse

Causaras, C.R.

1985-01-01

The geologic framework of the surficial aquifer system, of which the Biscayne aquifer is the major component in Broward County, Florida, is presented in eight geologic cross sections. The cross sections are based on detailed lithologic logs of 27 test wells that were drilled, in the summer of 1981, through the sediments overlying the relatively impermeable units of the Hawthorn Formation, of Miocene age. The cross sections show the aquifer system as a wedge-shaped sequence of Cenozoic sediments. The aquifer thickness gradually decreases from more than 400 feet along the coast to about 160 feet in the west and southwest parts of Broward County. The sediments that comprise the aquifer system range in age from Pliocene to Pleistocene and are assigned to the following stratigraphic units from bottom to top: Tamiami Formation, Caloosahatchee Marl, Fort Thompson Formation, Key Largo Limestone, Anastasia Formation, Miami Oolite, and Pamlico Sand. (USGS)

A new species of Dyoros (Brachiopoda; Chonetoidea) from Nevada (United States) and stratigraphic implications for the Pennsylvanian and Permian Antler Overlap assemblage [Une nouvelle espèce de Dyoros (Brachiopoda; Chonetoidea) du Nevada (États-Unis) et implications stratigraphiques pour le Complexe chevauchant d'Antler (Pennsylvanien et Permien)

USGS Publications Warehouse

Racheboeuf, Patrick R.; Moore, Thomas E.; Blodgett, Robert B.

2004-01-01

Newly discovered fossil localities in coarse-grained deposits of the Pennsylvanian and Permian Antler overlap assemblage in the southern Shoshone Range, north-central Nevada have yielded a low-diversity assemblage consisting chiefly of a new species of chonetoidean brachiopod: Dyoros (Lissosia) nevadaensis nov. sp. The subgenus Dyoros (Lissosia), is known from Leonardian and lower Guadalupian strata in North America, mainly in Texas. The coarse-grained lithology of the host strata, their unconformable relation on deformed lower Paleozoic rocks, and the Leonardian and(or) lower Guadalupian age indicated by Dyoros (Lissosia) provide evidence that host strata are younger than strata of the Antler overlap assemblage in nearby areas of the southern Shoshone Range and suggest that an unconformity of local extent may be present within the overlap assemblage. The fossil age ranges and lithologic data suggest that the host strata may be correlative with the Guadalupian Edna Mountain Formation, an unconformity-bounded unit that forms the upper part of the Antler sequence in the Battle Mountain area to the north. This correlation suggests that the unconformity beneath these strata may have regional extent in north-central Nevada. The origin of the inferred regional unconformity is unknown and may have resulted from relative changes of sea level or regional extensional or contractional tectonism in the area of the former Antler highlands, which forms the substrate for the Antler overlap assemblage. ?? 2004 Elsevier SAS. All rights reserved.

A continental scale model for dissolved silica mobilization in North America

NASA Astrophysics Data System (ADS)

Jansen, N.; Lauerwald, R.; Hartmann, J.; Dürr, H. H.; Loos, S.; Kempe, S.; Middelkoop, H.

2009-04-01

Silicon is one of the few elements that link to both the organic and inorganic carbon cycles. Dissolved silicon (DSi) is an important nutrient in terrestrial and aquatic ecosystems. Cations accompanying the release of DSi by chemical silicate rock weathering are generally balanced by soil/atmospheric CO2. Chemical weathering is the major source of "new" bioavailable DSi for continental aquatic systems to compensate for the loss of DSi by outflow or organic precipitation and burial. We use river water chemistry data from 164 monitoring stations from the conterminous United States (WQN and NAWQA networks). Selected stations are characterized by low population density and low influence of water bodies to minimize human and DSi retention impact. Observed DSi yield in these catchments is assumed to represent natural DSi mobilization by chemical weathering. The catchments have an average size of 4400 km2 (Median: 991 km2) with a discharge weighted average DSi yield of 4.34 t SiO2 km-2a-1. To predict mobilization of DSi from chemical weathering a lumped non-linear empirical model is developed, considering control factors such as climate, morphology, hydrology, land cover, soil and lithology. A multi-lithological model approach is chosen because only very few mono-lithological catchments were identified in the dataset. The model is then extrapolated to the conterminous United States to regionally quantify the amount of DSi that is released into the river systems by chemical weathering. Small outcrops of certain lithological classes characterized by a high DSi yield are not represented on previously available small scale lithological maps. Because such localities may have a major influence on DSi fluxes from small catchments (Hartmann et al., 2009) a new high resolution lithological vector-map for North America is developed and applied in the introduced model. In accordance with previous studies, runoff and lithology are identified as the major predictors for specific DSi flux (Bluth and Kump, 1994; Hartmann et al., 2009). Only in relation to some lithological classes, temperature and terrain slope constitute significant predictors. An influence of land cover, soil properties or other predictors is not observed. This is partly attributed to geodata resolution and classification. Lithological classes "Basic Volcanics and Pyroclastics" and "Basic and Intermediate Plutonics" show the highest DSi yields, with respect to a given discharge. The lithological class "Siliciclastic Sedimentary Rocks" is characterized by the lowest DSi yield. The model explains 89% of the DSi yield variance; the average yield of catchments employed in model calibration is 4.32 t SiO2 km-2a-1, somewhat above the global average yield of 3.3 t SiO2 km-2a-1 (Dürr et al., 2009). The model quantifies DSi fluxes from the terrestrial into the continental aquatic systems. This helps to estimate DSi retention within fluvial systems (Lauerwald et al., submitted) and improves understanding of this part of the silicon cycle. References: Bluth, G.J.S., and Kump, L.R., 1994, Lithologic and Climatologic Controls of River Chemistry: Geochimica Cosmochimica Acta, 58, 2341-2359. Dürr, H.H., Meybeck, M., Hartmann, J., Laruelle, G.G., and Roubeix, V., 2009, Global Spatial distribution of natural riverine silica inputs to the coastal zone: Biogeosciences, (in review), bgd-2008-0173. Hartmann, J., Jansen, N., Dürr, H.H., Harashima, A., Okubo, K., and Kempe, S., 2009, Predicting riverine dissolved silica fluxes into coastal zones from a hyperactive region and analysis of their first order controls: International Journal of Earth Sciences, (DOI 10.1007/s00531-008-0381-5). Lauerwald, R., Jansen N., Hartmann, J., Dürr, H.H., Loos, S., Kempe, S., Middelkoop, H., submitted, Modeling dissolved silica retention in the limnic system of North America. (Submitted to this session).

Lithogeochemical character of the near-surface bedrock in the Connecticut, Housatonic, and Thames River Basins

USGS Publications Warehouse

Robinson, Gilpin R.; Peper, John D.; Steeves, Peter A.; Desimone, Leslie A.

1999-01-01

This data layer shows the generalized lithologic and geochemical (lithogeochemical) character of near-surface bedrock in the Connecticut, Housatonic, and Thames River Basins and several other small basins that drain into Long Island Sound from Connecticut. The area includes most of Connecticut, western Massachusetts, eastern Vermont, western New Hampshire, and small parts of Rhode Island, New York, and Quebec, Canada.Bedrock geologic rock units are classified into 29 lithogeochemical rock units, on the basis of the relative reactivity of their constituent minerals to dissolution and other weathering reactions and the presence of carbonate or sulfide minerals. The 29 lithogeochemical units (28 of which can be found in the study area) can be grouped into 6 major categories: (1) carbonate-rich rocks, (2) carbonate-poor, clastic sedimentary rocks restricted to distinct depositional basins, (3) metamorphosed, clastic sedimentary rocks (primarily noncalcareous), (4) mafic igneous rocks and their metamorphic equivalents, (5) ultramafic rocks, and (6) felsic igneous and plutonic rocks and their metamorphic equivalents. The lithogeochemical rock units also are grouped into nine lithologic and physiographic provinces (lithophysiographic domains), which can be further grouped into three major regions: (1) western highlands and lowlands, (2) central lowlands, and (3) eastern highlands.

Analysis of deep seismic reflection and other data from the southern Washington Cascades

NASA Astrophysics Data System (ADS)

Stanley, W. D.; Johnson, S. Y.

Limited possibilities exist for new hydrocarbon exploration regimes in the Pacific Northwest. Extensive geophysical studies have been used to outline a proposed sedimentary basin hidden beneath volcanic rocks of the Cascades region of southwestern Washington (Stanley et. al, 1992, AAPG Bull. 76, 1569-1585). Electrical geophysical imaging using the magnetotelluric (MT) method first detected thick, electrically conductive sequences believed to represent late Cretaceous to Oligocene marine sedimentary rocks. The conductive section occurs at depths from about 1 km to 10 km in the area west of a line between Mt. Rainier and Mt. Adams, extending westward to a line between Mt. St. Helens and just west of Morton, WA. The conductive rocks reaches thicknesses as great as 10 km. The anomalous rocks appear to be very near the surface in the axis of anticanes that bring Eocene marine shales to shallow depths. Careful consideration of physical properties and the correspondence of the morphology of the units to known fold sets suggests that the high conductivities are related to lithologic/stratigraphic units rather than to variations in physical properties. Our preference for the lithology of the anomalous section, based upon a study of regional geology and structure, is one dominated by marine shales of Eocene and older age. Other possible lithologies that have been evaluated for the conductive section include nonmarine sedimentary units of Tertiary age, highly altered volcanic flows, and pre-Tertiary metasedimentary rocks with large percentages of graphite. We refer to this anomalously conductive region as the southern Washington Cascades conductor (SWCC).

Three-dimensional geologic model of the southeastern Espanola Basin, Santa Fe County, New Mexico

USGS Publications Warehouse

Pantea, Michael P.; Hudson, Mark R.; Grauch, V.J.S.; Minor, Scott A.

2011-01-01

This multimedia model and report show and describe digital three-dimensional faulted surfaces and volumes of lithologic units that confine and constrain the basin-fill aquifers within the Espanola Basin of north-central New Mexico. These aquifers are the primary groundwater resource for the cities of Santa Fe and Espanola, six Pueblo nations, and the surrounding areas. The model presented in this report is a synthesis of geologic information that includes (1) aeromagnetic and gravity data and seismic cross sections; (2) lithologic descriptions, interpretations, and geophysical logs from selected drill holes; (3) geologic maps, geologic cross sections, and interpretations; and (4) mapped faults and interpreted faults from geophysical data. Modeled faults individually or collectively affect the continuity of the rocks that contain the basin aquifers; they also help define the form of this rift basin. Structure, trend, and dip data not previously published were added; these structures are derived from interpretations of geophysical information and recent field observations. Where possible, data were compared and validated and reflect the complex relations of structures in this part of the Rio Grande rift. This interactive geologic framework model can be used as a tool to visually explore and study geologic structures within the Espanola Basin, to show the connectivity of geologic units of high and low permeability between and across faults, and to show approximate dips of the lithologic units. The viewing software can be used to display other data and information, such as drill-hole data, within this geologic framework model in three-dimensional space.

Macrostrat: A Platform for Geological Data Integration and Deep-Time Earth Crust Research

NASA Astrophysics Data System (ADS)

Peters, Shanan E.; Husson, Jon M.; Czaplewski, John

2018-04-01

Characterizing the lithology, age, and physical-chemical properties of rocks and sediments in the Earth's upper crust is necessary to fully assess energy, water, and mineral resources and to address many fundamental questions. Although a large number of geological maps, regional geological syntheses, and sample-based measurements have been produced, there is no openly available database that integrates rock record-derived data, while also facilitating large-scale, quantitative characterization of the volume, age, and material properties of the upper crust. Here we describe Macrostrat, a relational geospatial database and supporting cyberinfrastructure that is designed to enable quantitative spatial and geochronological analyses of the entire assemblage of surface and subsurface sedimentary, igneous, and metamorphic rocks. Macrostrat contains general, comprehensive summaries of the age and properties of 33,903 lithologically and chronologically defined geological units distributed across 1,474 regions in North and South America, the Caribbean, New Zealand, and the deep sea. Sample-derived data, including fossil occurrences in the Paleobiology Database, more than 180,000 geochemical and outcrop-derived measurements, and more than 2.3 million bedrock geologic map units from over 200 map sources, are linked to specific Macrostrat units and/or lithologies. Macrostrat has generated numerous quantitative results and its infrastructure is used as a data platform in several independently developed mobile applications. It is necessary to expand geographic coverage and to refine age models and material properties to arrive at a more precise characterization of the upper crust globally and test fundamental hypotheses about the long-term evolution of Earth systems.

Remote sensing detection of gold related alteration zones in Um Rus area, Central Eastern Desert of Egypt

NASA Astrophysics Data System (ADS)

Amer, Reda; Kusky, Timothy; El Mezayen, Ahmed

2012-01-01

Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) and Phased Array L-band Synthetic Aperture Radar (PALSAR) images covering the Um Rus area in the Central Eastern Desert of Egypt were evaluated for mapping geologic structure, lithology, and gold-related alteration zones. The study area is covered by Pan-African basement rocks including gabbro and granodiorite intruded into a variable mixture of metavolcanics and metasediments. The first three principal component analyses (PCA1, PCA2, PCA3) in a Red-Green-Blue (RGB) of the visible through shortwave-infrared (VNIR + SWIR) ASTER bands enabled the discrimination between lithological units. The results show that ASTER band ratios ((2 + 4)/3, (5 + 7)/6, (7 + 9)/8) in RGB identifies the lithological units and discriminates the granodiorite very well from the adjacent rock units.The granodiorites are dissected by gold-bearing quartz veins surrounded by alteration zones. The microscopic examination of samples collected from the alteration zones shows sericitic and argillic alteration zones. The Spectral Angle Mapper (SAM) and Spectral Information Divergence (SID) supervised classification methods were applied using the reference spectra of the USGS spectral library. The results show that these classification methods are capable of mapping the alteration zones as indicated by field verification work. The PALSAR image was enhanced for fracture mapping using the second moment co-occurrence filter. Overlying extracted faults and alteration zone classification images show that the N30E and N-S fractures represent potential zones for gold exploration. It is concluded that the proposed methods can be used as a powerful tool for ore deposit exploration.

Nature and origin of upper crustal seismic velocity fluctuations and associated scaling properties: Combined stochastic analyses of KTB velocity and lithology logs

USGS Publications Warehouse

Goff, J.A.; Holliger, K.

1999-01-01

The main borehole of the German Continental Deep Drilling Program (KTB) extends over 9000 m into a crystalline upper crust consisting primarily of interlayered gneiss and metabasite. We present a joint analysis of the velocity and lithology logs in an effort to extract the lithology component of the velocity log. Covariance analysis of lithology log, approximated as a binary series, indicates that it may originate from the superposition of two Brownian stochastic processes (fractal dimension 1.5) with characteristic scales of ???2800 m and ???150 m, respectively. Covariance analysis of the velocity fluctuations provides evidence for the superposition of four stochastic process with distinct characteristic scales. The largest two scales are identical to those derived from the lithology, confirming that these scales of velocity heterogeneity are caused by lithology variations. The third characteristic scale, ???20 m, also a Brownian process, is probably related to fracturing based on correlation with the resistivity log. The superposition of these three Brownian processes closely mimics the commonly observed 1/k decay (fractal dimension 2.0) of the velocity power spectrum. The smallest scale process (characteristic scale ???1.7 m) requires a low fractal dimension, ???1.0, and accounts for ???60% of the total rms velocity variation. A comparison of successive logs from 6900-7140 m depth indicates that such variations are not repeatable and thus probably do not represent true velocity variations in the crust. The results of this study resolve disparity between the differing published estimates of seismic heterogeneity based on the KTB sonic logs, and bridge the gap between estimates of crustal heterogeneity from geologic maps and borehole logs. Copyright 1999 by the American Geophysical Union.

Parameters controlling mechanical stratification of gas-bearing shale complexes: integration of wellbore logging and core profiling (Peri-Baltic Basin, Poland).

NASA Astrophysics Data System (ADS)

Pachytel, Radomir; Jarosiński, Marek; Bobek, Kinga; Roszkowska-Remin, Joanna; Roman, Michał

2016-04-01

In our study of mechanical properties of gas-bearing shale complexes from exploration wells in Pomerania, we take advantage from having access to continuous, several hundred meters long core profiles which are supplemented with complete sets of geophysical logging from the same shale intervals. We are focused on different approaches to discriminate the Consistent Mechanical Units (CMUs). Such units are essential for mechanical modeling of stress and strain in shales and their scale is highly dependent on the purpose of analyses. We have done a precise lithological and structural core profiling, which results in distinguishing Consistent Lithological Units (CLUs) at a centimeter scale. The geophysical logs, essential for mechanical studies, exhibit resolution from tens of centimeters to a meter. The meter resolution we have found appropriate for consideration of mechanics of hydraulic fracture propagation and therefore we have used it in CMUs analysis. The first challenge we have faced is to switch between scales of analyses without significant losses of information coming from the lower level of observation. The next challenge, is to find the mechanical parameter which is able to discriminate CMUs most efficiently. Brittleness Indexes (BIs) are commonly used parameters in order to characterize mechanical shale units, but at the same time these indexes are arbitrary defined to match individual requirements of the users. In our study, we have determined the BIs in several ways, based either on mineral composition or on elastic modules, both supplemented with pore volume. The gamma ray (GR), Young modulus (YM), Poisson Ratio (ν) interpretation from acoustic logging, bulk density (RHOB), porosity interpretation (ø) and mineralogical profile (ULTRA, GEM) from spectral logging were computed. Detailed comparison of lithological profile and discriminated CLUs with above logs led us to conclusions about geophysical representation of dolomite and silica lithified shale, organic matter enrichment tuffite layers or disturbances in lamination, which are important for mechanical differentiation of shale complexes. Finally, we have checked which of the calculated BIs matches best the lithological differentiation and the natural fracture density profile that allowed us for selection of the BI which, in our opinion, represents the potential for hydraulic fracture propagation. Our study in the frame of ShaleMech Project (Blue Gas Program) is in progress and the results are preliminary.

Lithologic mapping in the Mountain Pass, California area using Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data

USGS Publications Warehouse

Rowan, L.C.; Mars, J.C.

2003-01-01

Evaluation of an Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) image of the Mountain Pass, California area indicates that several important lithologic groups can be mapped in areas with good exposure by using spectral-matching techniques. The three visible and six near-infrared bands, which have 15-m and 30-m resolution, respectively, were calibrated by using in situ measurements of spectral reflectance. Calcitic rocks were distinguished from dolomitic rocks by using matched-filter processing in which image spectra were used as references for selected spectral categories. Skarn deposits and associated bright coarse marble were mapped in contact metamorphic zones related to intrusion of Mesozoic and Tertiary granodioritic rocks. Fe-muscovite, which is common in these intrusive rocks, was distinguished from Al-muscovite present in granitic gneisses and Mesozoic granite. Quartzose rocks were readily discriminated, and carbonate rocks were mapped as a single broad unit through analysis of the 90-m resolution, five-band surface emissivity data, which is produced as a standard product at the EROS Data Center. Three additional classes resulting from spectral-angle mapper processing ranged from (1) a broad granitic rock class (2) to predominately granodioritic rocks and (3) a more mafic class consisting mainly of mafic gneiss, amphibolite and variable mixtures of carbonate rocks and silicate rocks. ?? 2002 Elsevier Science Inc. All rights reserved.

Interpretation of borehole geophysical logs, aquifer-isolation tests, and water quality, supply wells 1 and 2, Willow Grove Naval Air Station/Joint Reserve Base, Horsham Township, Montgomery County, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.; Goode, Daniel J.; Frasch, Steven M.

2002-01-01

Ground water pumped from supply wells 1 and 2 on the Willow Grove Naval Air Station/Joint Reserve Base (NAS/JRB) provides water for use at the base, including potable water for drinking. The supply wells have been contaminated by volatile organic compounds (VOC's), particularly trichloroethylene (TCE) and tetrachloroethylene (PCE), and the water is treated to remove the VOC's. The Willow Grove NAS/JRB and surrounding area are underlain by sedimentary rocks of the Triassic-age Stockton Formation, which form a complex, heterogeneous aquifer.The ground-water-flow system for the supply wells was characterized by use of borehole geophysical logs and heatpulse-flowmeter measurements. The heatpulse-flowmeter measurements showed upward and downward borehole flow under nonpumping conditions in both wells. The hydraulic and chemical properties of discrete water-bearing fractures in the supply wells were characterized by isolating each water-bearing fracture with straddle packers. Eight fractures in supply well 1 and five fractures in supply well 2 were selected for testing on the basis of the borehole geophysical logs and borehole television surveys. Water samples were collected from each isolated fracture and analyzed for VOC?s and inorganic constituents.Fractures at 50–59, 79–80, 196, 124–152, 182, 241, 256, and 350–354 ft btoc (feet below top of casing) were isolated in supply well 1. Specific capacities ranged from 0.26 to 5.7 (gal/min)/ft (gallons per minute per foot) of drawdown. The highest specific capacity was for the fracture isolated at 179.8–188 ft btoc. Specific capacity and depth of fracture were not related in either supply well. The highest concentrations of PCE were in water samples collected from fractures isolated at 236.8–245 and 249.8–258 ft btoc, which are hydraulically connected. The concentration of PCE generally increased with depth to a maximum of 39 mg/L (micrograms per liter) at a depth of 249.8? 258 ft btoc and then decreased to 21 mg/L at a depth of 345.3–389 ft btoc.Fractures at 68–74, 115, 162, 182, 205, and 314 ft btoc were isolated in supply well 2. Specific capacities ranged from 0.08 to less than 2.9 (gal/ min)/ft. The highest specific capacity was for the fracture isolated at 157–165.2 ft btoc. Concentrations of detected VOC's in water samples were 3.6 mg/L or less.Lithologic units penetrated by both supply wells were determined by correlating naturalgamma and single-point-resistance borehole geophysical logs. All lithologic units are not continuous water-bearing units because water-bearing fractures are not necessarily present in the same lithologic units in each well. Although the wells penetrate the same lithologic units, the lithologic location of only three water-bearing fractures are common to both wells. The same lithologic unit may have different hydraulic properties in each well.A regional ground-water divide is southeast of the supply wells. From this divide, ground water flows northwest toward Park Creek, a tributary to Little Neshaminy Creek. Potentiometric-surface maps were prepared from water levels measured in shallow and deep wells. For both depth intervals, the direction of ground-water flow is toward the northwest. For most well clusters, the vertical head gradient is downward from the shallow to the deeper part of the aquifer. Pumping of the supply wells at times can cause the vertical flow direction to reverse.

Use of spectral gamma ray as a lithology guide for fault rocks: A case study from the Wenchuan Earthquake Fault Scientific Drilling project Borehole 4 (WFSD-4).

PubMed

Amara Konaté, Ahmed; Pan, Heping; Ma, Huolin; Qin, Zhen; Guo, Bo; Yevenyo Ziggah, Yao; Kounga, Claude Ernest Moussounda; Khan, Nasir; Tounkara, Fodé

2017-10-01

The main purpose of the Wenchuan Earthquake Fault Scientific drilling project (WFSD) was to produce an in-depth borehole into the Yingxiu-Beichuan (YBF) and Anxian-Guanxian faults in order to gain a much better understanding of the physical and chemical properties as well as the mechanical faulting involved. Five boreholes, namely WFSD-1, WFSD-2, WFSD-3P, WFSD-3 and WFSD-4, were drilled during the project entirety. This study, therefore, presents first-hand WFSD-4 data on the lithology (original rocks) and fault rocks that have been obtained from the WFSD project. In an attempt to determine the physical properties and the clay minerals of the lithology and fault rocks, this study analyzed the spectral gamma ray logs (Total gamma ray, Potassium, Thorium and Uranium) recorded in WFSD-4 borehole on the Northern segment of the YBF. The obtained results are presented as cross-plots and statistical multi log analysis. Both lithology and fault rocks show a variability of spectral gamma ray (SGR) logs responses and clay minerals. This study has shown the capabilities of the SGR logs for well-logging of earthquake faults and proves that SGR logs together with others logs in combination with drill hole core description is a useful method of lithology and fault rocks characterization. Copyright © 2017 Elsevier Ltd. All rights reserved.

Chemical composition of sedimentary rocks in California and Hawaii

USGS Publications Warehouse

Hill, Thelma P.

1981-01-01

A compilation of published chemical analyses of sedimentary rocks of the United States was undertaken by the U.S. Geological Survey in 1952 to make available scattered data that are needed for a wide range of economic and scientific uses. About 20,000-25,000 chemical analyses of sedimentary rocks in the United States have been published. This report brings together 2,312 of these analyses from California and Hawaii. The samples are arranged by general lithologic characteristics and locality. Indexes of stratigraphy, rock name, commercial uses, and minor elements are provided. The sedimentary rocks are classified into groups and into categories according to the chemical analyses. The groups (A through F2) are defined by a system similar to that proposed by Brian Mason in 1952, in which the main parameters are the three major components of sedimentary rocks: (1) uncombined silica, (2) clay (R203 ? 3Si02 ? nH20), and (3) calcium-magnesium carbonate. The categories are based on the degree of admixture of these three major components with other components, such as sulfate, phos- phate, and iron oxide. Common-rock, mixed-rock, and special-rock categories apply to rocks consisting of 85 percent or more, 50-84 percent, and less than 49 percent, respectively, of the three major components combined. Maps show distribution of sample localities by States; triangular diagrams show the lithologic characteristics and classification groups. Cumulative-frequency curves of each constituent in each classification group of the common-rock and mixed-rock categories are also included. The numerous analyses may not adequately represent the geochemical nature of the rock types and formations of the region because of sampling bias. Maps showing distribution of sample localities indicate that many of the localities are in areas where, for economic or other reasons, special problems attracted interest. Most of the analyzed rocks tended to be fairly simple in composition - mainly mixtures of just two of the three major components or a mixture of these and a fourth component such as phosphate, gypsum, or iron oxide.

Digital Tabulation of Geologic and Hydrologic Data from Water Wells in the Northern San Francisco Bay Region, Northern California

USGS Publications Warehouse

Sweetkind, D.S.; Taylor, E.M.

2010-01-01

Downhole lithologic information and aquifer pumping test data are reported from 464 wells from a broad area of the northern part of the Coast Ranges in California. These data were originally published in paper form as numerous tables within three USGS Water-Supply Papers describing geology and groundwater conditions in Napa and Sonoma Valleys, the Santa Rosa and Petaluma Valley areas, and in the Russian River Valley and areas in Sonoma and Mendocino Counties, Calif. The well data are compiled in this report in digital form suitable for use in a digital mapping environment. These data, although mostly from relatively shallow water wells, provide important subsurface information that displays the disposition and facies transition of lithologic units throughout this broad area. Well lithologic data themselves and simple three-dimensional interpolation of those data show distinct spatial patterns that are linked to subsurface stratigraphy and structure and can be used to aid in the assessment of the groundwater resources.

Notes on Lithology, Mineralogy, and Production for Lunar Simulants

NASA Technical Reports Server (NTRS)

Rickman, D. L.; Stoeser, D. B.; Benzel, W. M.; Schrader, C. M.; Edmunson, J. E.

2011-01-01

The creation of lunar simulants requires a very broad range of specialized knowledge and information. This document covers several topic areas relevant to lithology, mineralogy, and processing of feedstock materials that are necessary components of the NASA lunar simulant effort. The naming schemes used for both terrestrial and lunar igneous rocks are discussed. The conflict between the International Union of Geological Sciences standard and lunar geology is noted. The rock types known as impactites are introduced. The discussion of lithology is followed by a brief synopsis of pyroxene, plagioclase, and olivine, which are the major mineral constituents of the lunar crust. The remainder of the text addresses processing of materials, particularly the need for separation of feedstock minerals. To illustrate this need, the text includes descriptions of two norite feedstocks for lunar simulants: the Stillwater Complex in Montana, United States, and the Bushveld Complex in South Africa. Magnetic mineral separations, completed by Hazen Research, Inc. and Eriez Manufacturing Co. for the simulant task, are discussed.

Selected Ground-Water Data for Yucca Mountain Region, Southern Nevada and Eastern California, January 2000-December 2002

DTIC Science & Technology

2003-01-01

Thordarson and others (1967). Contributing units: Saturated lithologic interval yielding water to well. C, carbonate rock; F, valley fill; S, undifferentiated...AD-6, AD-8, and AM-4. Thordarson and others (1967) describe the contributing unit at site RV-1. Dudley and Larson (1976) describe the contributing...and measurements of depth to water. Contributing units for springs indicate sources of water discharged at the sites. Winograd and Thordarson

Mechanical-Stratigraphic Characterization of the Eagle Ford Formation in Outcrop and Core, McMullen and Terrell Counties, Texas

NASA Astrophysics Data System (ADS)

Xu, G.; Chester, J. S.; Chester, F. M.

2017-12-01

The objective of this project is to characterize the geomechanical properties of individual and composite lithologic units over length scales of decimeter to tens of meters. We have characterized the stratigraphy and lithology of the Eagle Ford Formation in outcrops at Lozier and Antonio Canyons of West TX, and in core taken at 3.2 km depth in McMullen County, TX. Dominant lithologies examined include reworked ash layers, argillaceous mudstone, organic-rich mudstone, foraminifera wackestone, packstone, pyritic packstone, and foraminifera/dolomitic packstone-grainstone. Samples of these units are deformed in triaxial compression at 1- 40 MPa confining pressure (Pc), and room temperature and humidity. The elastic properties, pre-fracture yielding (ductility), and fracture strength are primarily a function of particle size, texture (degree of mud versus grain support), and composition. Young's Modulus (YM) and Poison's Ratio (PR) increase similarly with an increase in grain-support and carbonate content, and a decrease in organic matter and clay. The greatest change occurs at the transition from mud-supported to grain-supported textures where YM and PR increase by a factor of 3 and 1.5, respectively. Both YM and PR can display anisotropy with directional variation of 30%, most notably in micro-laminated units, but also in the more massive pyritic packstones. Overall, pre-fracture ductility decreases with an increase in carbonate content; ductile strain in the argillaceous- and organic-rich-mudstones is 1.4%, 3-4 times greater than that in the packstone/grainstone. Fracture strength increases with an increase in carbonate content and a decrease in clay content. The organic rich mudstone fails at 130 MPa, is nearly 2 times stronger than argillaceous mudstones, and 50% weaker than packstone/grainstones at 1 MPa Pc. The angle of internal friction is 45 degrees for all lithologies, consistent with a transition in fracture from opening- to shear-mode between 1 to 15 MPa Pc. These data indicate that the Eagle Ford Formation is mechanically anisotropic at all length scales, and although elastic and inelastic properties correlate overall, significant variations between properties reflect differences in dependence on composition and texture.

Oxygen and carbon isotope compositions of carbonates in a prominent lithologically mixed unit in the central South Norwegian Caledonides

NASA Astrophysics Data System (ADS)

Jakob, Johannes; Boulvais, Philippe; Andersen, Torgeir B.

2018-06-01

A prominent pre-Scandian lithologically mixed unit in the central South Norwegian Caledonides contains more than 100 partly carbonated and hydrated metaperidotite bodies and locally fossiliferous detrital serpentinites. The lateral consistency of this mixed unit was not fully appreciated in the past. Therefore, parts of the mixed unit along strike were interpreted to belong to several different tectonostratigraphic levels. Here, we present new carbonate stable isotope data that suggest that the carbonates of the mixed unit between Bergen and Otta (re-)equilibrated at unit-wide similar peak metamorphic conditions. The isotope compositions are characteristic for this unit and indicate that it represented one single tectonic unit during the Scandian Orogeny. The carbonates in the mélange are characterized by a narrow range of δ18O (SMOW) values between + 11 and + 15.5‰ and three groups of δ13C (PDB) values: (I) + 1.6 to + 0.3‰, (II) - 1.8 to - 3.9‰, and (III) - 6 to - 8.6‰. Carbonates of group III probably were affected by decarbonation or by a fluid containing organic carbon, whereas carbonates of group I and II overlap with δ13C values typical for Ediacaran-Silurian marine carbonates and may have retained their initial δ13C imprint. We suggest that the δ18O values (re-)equilibrated with unit-wide released metamorphic fluids during Scandian metamorphism. An outcrop-scale homogenisation of the δ13C values reflects the local carbon isotope signature of the released metamorphic fluids that circulated channelized through the mélange unit.

Oxygen and carbon isotope compositions of carbonates in a prominent lithologically mixed unit in the central South Norwegian Caledonides

NASA Astrophysics Data System (ADS)

Jakob, Johannes; Boulvais, Philippe; Andersen, Torgeir B.

2017-11-01

A prominent pre-Scandian lithologically mixed unit in the central South Norwegian Caledonides contains more than 100 partly carbonated and hydrated metaperidotite bodies and locally fossiliferous detrital serpentinites. The lateral consistency of this mixed unit was not fully appreciated in the past. Therefore, parts of the mixed unit along strike were interpreted to belong to several different tectonostratigraphic levels. Here, we present new carbonate stable isotope data that suggest that the carbonates of the mixed unit between Bergen and Otta (re-)equilibrated at unit-wide similar peak metamorphic conditions. The isotope compositions are characteristic for this unit and indicate that it represented one single tectonic unit during the Scandian Orogeny. The carbonates in the mélange are characterized by a narrow range of δ18O (SMOW) values between + 11 and + 15.5‰ and three groups of δ13C (PDB) values: (I) + 1.6 to + 0.3‰, (II) - 1.8 to - 3.9‰, and (III) - 6 to - 8.6‰. Carbonates of group III probably were affected by decarbonation or by a fluid containing organic carbon, whereas carbonates of group I and II overlap with δ13C values typical for Ediacaran-Silurian marine carbonates and may have retained their initial δ13C imprint. We suggest that the δ18O values (re-)equilibrated with unit-wide released metamorphic fluids during Scandian metamorphism. An outcrop-scale homogenisation of the δ13C values reflects the local carbon isotope signature of the released metamorphic fluids that circulated channelized through the mélange unit.

Assembling the Anthropocene: deep-time perspective on the development of a lithostratigraphic classification of Anthropogenic deposits and excavations

NASA Astrophysics Data System (ADS)

Waters, C. N.; Ford, J. R.; Price, S.; Cooper, A. H.

2012-12-01

Human modification of the Earth's surface/subsurface is associated with artificial deposits (anthropogenic sedimentary units) and excavated ground (anthropogenic unconformities), analogous to ancient depositional systems. This study examines how artificial ground can be classified by the procedures used for natural deposits. Anthropogenic deposits have different characteristics to other parts of the stratigraphic column: 1) they vary greatly in lateral and vertical extent; 2) they are strictly allostratigraphic, i.e. defined and identified by bounding discontinuities, either unconformities (e.g. artificial deposits resting directly upon bedrock), disconformities (e.g. a time-gap between parallel artificial strata associated with non-deposition or reworking) or the present-day land surface; 3) many units have no overlying strata or bounding surface; 4) they are often poorly exposed, though associated landforms/geomorphology may show characteristic features that can aid definition. Artificial deposits comprise modified geologic materials, e.g. sand, clay, coal and novel anthropogenic materials, e.g. plastic, brick, glass. Such deposits are typically heterogeneous, the lithology determined for practical purposes by current/former landuse activity. BGS maps for the UK use a five-fold morpho-stratigraphic subdivision with no lithological attribution. An enhanced BGS scheme (Price et al. 2011) uses a three-tier hierarchy to describe the origin and landform of the deposit or excavation with lithology and age treated as additional attributes. Though based largely on geomorphlogical expression and genetic origin, the scheme can be used for classifying subsurface deposits lacking landform expression. Anthropogenic modification ('anthropoturbation') of rock and natural sediments, e.g. boreholes, tunnels and mineshafts, may extend to significant depths. Although indicating the extent of human influence they do not affect the classification of the stratigraphy; analogous to post-depositional tectonics not resulting in renamed lithostratigraphic units. However, it may be necessary to classify large non-stratiform bodies, i.e. underground infilled cavities, as lithodemic units in a manner applicable to igneous intrusive rocks. A lithostratigraphic scheme for the Anthropocene should conform to international stratigraphic principles (Salvador 1994), each unit named after an appropriate geographic location and defined by a stratotype. Inclusion of a lithologic term is discouraged by Salvador (1994) and because of the inherent heterogeneity of artificial deposits would be unsuitable. However, additional morphologic/genetic epithets could be included for low ranking units. PRICE, S.J., FORD, J.R., COOPER, A.H. & NEAL, C. 2011. Humans as major geological and geomorphological agents in the Anthropocene: the significance of artificial ground in Great Britain. Philosophical Transactions of the Royal Society, A2011 369, 1056-1084. SALVADOR, A. 1994. International Stratigraphic Guide. A guide to stratigraphic classification, terminology, and procedure. 2nd Edition. The International Union of Geological Sciences and The Geological Society of America (Colorado). 214 pp.

Geological and physicochemical controls of the spatial distribution of partition coefficients for radionuclides (Sr-90, Cs-137, Co-60, Pu-239,240 and Am-241) at a site of nuclear reactors and radioactive waste disposal (St. Petersburg region, Russian Federation).

PubMed

Rumynin, Vyacheslav G; Nikulenkov, Anton M

2016-10-01

The paper presents a study of the sorption properties of sediments of different geological ages and lithological types, governing radionuclide retention in the subsurface (up to 160 m beneath the surface) within the area of potential influence of the Northwestern Center of Atomic Energy (NWCAE), St. Petersburg region, RF. The focus of this work is mostly on the sedimentary rocks of two types, i.e., weakly cemented sandstone and lithified clay formations of Cambrian and Vendian series. The first lithological unit is associated with a groundwater reservoir (Lomonosov aquifer), and the second one, with both a relative aquitard in the upper part of the Vendian formation (Kotlin clay) and a regional aquifer (Gdov aquifer) in the lower part of the formation. The main mechanisms responsible for the variability of the sorption distribution coefficient (Kd, defined as the ratio of the concentration of solute on solid phase to its concentration in solution at equilibrium) was identified for radionuclides such as Sr-90, Cs-137, Co-60, Pu-239,240, and Am-241. It was shown that the main factors contributing to the chemical heterogeneity of the Cambrian sandstone were related to the presence of secondary minerals (iron and magnesium oxides and hydroxides produced by the weathering process) in trace amounts, forming correlated layer structures. The statistical analysis of nonlinear isotherms confirmed this conclusion. For the Vendian formation, a determinate trend was established in the Kd change over depth as a result of temporal trends in the sedimentation process and pore-water chemistry. The geostatistical characteristics and the spatial correlation models for describing linear sorption of different radionuclides are not identical, and the exhibition of chemical heterogeneity of sedimentary rock of a particular lithological type depends on radionuclide chemistry. Moreover, variogram analysis for some Kd data sets (both in Cambrian and Vendian formations) demonstrates the total absence of auto-correlation (pure nugget effect). It can be supposed that sampling distances did not allow the evaluation of small-scale variability in sediment sorption properties. Copyright © 2016 Elsevier Ltd. All rights reserved.

Facies analysis of Tertiary basin-filling rocks of the Death Valley regional ground-water system and surrounding areas, Nevada and California

USGS Publications Warehouse

Sweetkind, Donald S.; Fridrich, Christopher J.; Taylor, Emily

2001-01-01

Existing hydrologic models of the Death Valley region typically have defined the Cenozoic basins as those areas that are covered by recent surficial deposits, and have treated the basin-fill deposits that are concealed under alluvium as a single unit with uniform hydrologic properties throughout the region, and with depth. Although this latter generalization was known to be flawed, it evidently was made because available geologic syntheses did not provide the basis for a more detailed characterization. As an initial attempt to address this problem, this report presents a compilation and synthesis of existing and new surface and subsurface data on the lithologic variations between and within the Cenozoic basin fills of this region. The most permeable lithologies in the Cenozoic basin fills are freshwater limestones, unaltered densely welded tuffs, and little-consolidated coarse alluvium. The least permeable lithologies are playa claystones, altered nonwelded tuffs, and tuffaceous and clay-matrix sediments of several types. In all but the youngest of the basin fills, permeability probably decreases strongly with depth owing to a typically increasing abundance of volcanic ash or clay in the matrices of the clastic sediments with increasing age (and therefore with increasing depth in general), and to increasing consolidation and alteration (both hydrothermal and diagenetic) with increasing depth and age. This report concludes with a categorization of the Cenozoic basins of the Death Valley region according to the predominant lithologies in the different basin fills and presents qualitative constraints on the hydrologic properties of these major lithologic categories.

Lithogeochemical character of near-surface bedrock in the New England coastal basins

USGS Publications Warehouse

Robinson, Gilpin R.; Ayotte, Joseph D.; Montgomery, Denise L.; DeSimone, Leslie A.

2002-01-01

This geographic information system (GIS) data layer shows the generalized lithologic and geochemical, termed lithogeochemical, character of near-surface bedrock in the New England Coastal Basin (NECB) study area of the U.S. Geological Survey's National Water Quality Assessment (NAWQA) Program. The area encompasses 23,000 square miles in western and central Maine, eastern Massachusetts, most of Rhode Island, eastern New Hampshire and a small part of eastern Connecticut. The NECB study area includes the Kennebec, Androscoggin, Saco, Merrimack, Charles, and Blackstone River Basins, as well as all of Cape Cod. Bedrock units in the NECB study area are classified into lithogeochemical units based on the relative reactivity of their constituent minerals to dissolution and the presence of carbonate or sulfide minerals. The 38 lithogeochemical units are generalized into 7 major groups: (1) carbonate-bearing metasedimentary rocks; (2) primarily noncalcareous, clastic sedimentary rocks with restricted deposition in discrete fault-bounded sedimentary basins of Mississipian or younger age; (3) primarily noncalcareous, clastic sedimentary rocks at or above biotite-grade of regional metamorphism; (4) mafic igneous rocks and their metamorphic equivalents; (5) ultramafic rocks; (6) felsic igneous rocks and their metamorphic equivalents; and (7) unconsolidated and poorly consolidated sediments.

Criteria for the recognition and correlation of sandstone units in the Precambrian and Paleozoic-Mesozoic clastic sequence in the near east

NASA Astrophysics Data System (ADS)

Weissbrod, T.; Perath, I.

A systematic study of the Precambrian and Paleozoic-Mesozoic clastic sequences (Nubian Sandstone) in Israel and Sinai, and a comparative analysis of its stratigraphy in neighbouring countries, has shown that besides the conventional criteria of subdivision (lithology, field appearance, photogeological features, fossil content), additional criteria can be applied, which singly or in mutual conjuction enable the recognition of widespread units and boundaries. These criteria show lateral constancy, and recurrence of a similar vertical sequence over great distances, and are therefore acceptable for the identification of synchronous, region-wide sedimentary units (and consequently, major unconformities). They also enable, once the units are established, to identify detached (not in situ) samples, samples from isolated or discontinous outcrops, borehole material or archive material. The following rock properties were tested and found to be usefuls in stratigraphic interpretation, throughout large distribution areas of the clastic sequence: Landscape, which is basically the response of a particular textural-chemic al aggregate to atmospheric weathering. Characteristic outcrop feature — styles of roundness or massivity, fissuring or fliatin, slope profile, bedding — express a basic uniformity of these platform-type clastics. Colors are often stratigraphically constant over hundreds of kilometers, through various climates and topographies, and express some intrinsic unity of the rock bodies. Grain size and sorting, when cross-plotted, enable to differentiate existing unit. The method requires the analysis of representative numbers of samples. Vertical trends of median grain size and sorting show reversals, typically across unconformities. Feldstar content diminishes from 15-50% in Precambrian-Paleozoic rocks to a mere 5% or less in Mesozoic sandstones — a distinctive regionwide time trend. Dominance of certain feldstar types characterizes Precambrian and Paleozoic units. Clay minerals, though subordinate, characterize certain units. Illite is usually the dominant clay mineral in the Precambrain-Paleozoic sediments, showing different degress of crystallization in different units. Kaolinite is the main, often the only clay mineral in Mesozoic units. Heavy minerals, whose species spectra reflect on parent rock and provenance terrain and whose differential response to degradation points to the sedimentary history of the deposit, show certain vertical regularities, such as the abrupt disappearance of species or whole assemblages at certain levels, indicating unconformities. Trace metals, which in places reach ore concentrations (e.g. copper), are often extensive, though of well-defined vertical distribution. They express adsorptive capacity of specific widespread lithologies, enabling the discrimination of units. Even though each of these criteria is not always by itself diagnostic, they may in conjuction with one or more other criteria amount to a petrographic fingerprint that enables fairly accurate identification of the age interval of the unit, and its relation both to the regional and the local stratigraphic sequence.

Dust deposition in southern Nevada and California, 1984-1989: Relations to climate, source area, and source lithology

NASA Astrophysics Data System (ADS)

Reheis, Marith C.; Kihl, Rolf

1995-05-01

Dust samples collected annually for 5 years from 55 sites in southern Nevada and California provide the first regional source of information on modern rates of dust deposition, grain size, and mineralogical and chemical composition relative to climate and to type and lithology of dust source. The average silt and clay flux (rate of deposition) in southern Nevada and southeastern California ranges from 4.3 to 15.7 g/m2/yr, but in southwestern California the average silt and clay flux is as high as 30 g/m2/yr. The climatic factors that affect dust flux interact with each other and with the factors of source type (playas versus alluvium), source lithology, geographic area, and human disturbance. Average dust flux increases with mean annual temperature but is not correlated to decreases in mean annual precipitation because the regional winds bring dust to relatively wet areas. In contrast, annual dust flux mostly reflects changes in annual precipitation (relative drought) rather than temperature. Although playa and alluvial sources produce about the same amount of dust per unit area, the total volume of dust from the more extensive alluvial sources is much larger. In addition, playa and alluvial sources respond differently to annual changes in precipitation. Most playas produce dust that is richer in soluble salts and carbonate than that from alluvial sources (except carbonate-rich alluvium). Gypsum dust may be produced by the interaction of carbonate dust and anthropogenic or marine sulfates. The dust flux in an arid urbanizing area may be as much as twice that before disturbance but decreases when construction stops. The mineralogic and major-oxide composition of the dust samples indicates that sand and some silt is locally derived and deposited, whereas clay and some silt from different sources can be far-traveled. Dust deposited in the Transverse Ranges of California by the Santa Ana winds appears to be mainly derived from sources to the north and east.

Geometry, structure, and concealed lithology of the San Rafael Basin, southeastern Arizona

USGS Publications Warehouse

Bultman, Mark W.

1999-01-01

The contiguous United States has been well explored for exposed conventional mineral deposits. Therefore, it is likely that many economically viable and strategically significant conventional undiscovered mineral deposits will be found in bedrock concealed beneath basin sediments. Mineral resource assessments must incorporate an understanding of the geometry, structure, and concealed lithology of basins in order to be accurate. This report presents an analysis of the basin geometry and structure of the San Rafael basin in southeastern Arizona. In addition, a new methodology for inferring concealed lithology is presented and applied in the San Rafael basin. Gravity data is used to model the geometry of the basin using recent models of sediment density vs. depth developed in the region. This modeling indicates that the basin has a maximum depth of approximately 1.05 km plus or minus 0.10 km. In the southern portion, the basin can be modeled as an asymmetric graben faulted on the western margin. The northern portion of the basin is structurally more complex and may have high angle faults on the western, northern, and eastern margin. Near-ground closely spaced Earth’s total intensity magnetic field data is used to locate concealed faults within the basin. This data is also used to infer lithology concealed by shallow basin sediments. Airborne Earth’s total intensity magnetic field data is used to help infer concealed lithology in deep portions of the basin. The product of integrating all data and interpretations is a map which presents the geometry of the basin, faults and contacts concealed by basin sediments, and an estimate of the bedrock lithology concealed by basin sediment. Based on basin geometry and concealed lithology, the San Rafael basin has a high potential for concealed mineral deposits on its western and northern margin. In particular, a newly discovered magnetic anomaly in the northern portion of the basin can be modeled as a granitic intrusion with highly altered margins and may represent a potential mineral resource target. Based on the permeability and porosity of upper basin fill found in nearby basins, the San Rafael basin may contain an aquifer up to 300 meters thick over a substantial area of the basin.

Upper Neoproterozoic-Lower Cambrian sedimentary successions in the Central Iberian Zone (Spain): sequence stratigraphy, petrology and chemostratigraphy. Implications for other European zones

NASA Astrophysics Data System (ADS)

Valladares, M. I.; Barba, P.; Ugidos, J. M.; Colmenero, J. R.; Armenteros, I.

The Upper Neoproterozoic-Lower Cambrian sedimentary succession in the central areas of the Central Iberian Zone has been subdivided into 12 mostly siliciclastic lithostratigraphic units, ranging in thickness between 1800 and 3900m. The lithology and facies of each unit are described and the facies associations are interpreted. The facies resulted mainly from turbidity currents and debris flows and, to a lesser extent, from submarine slides and traction flows. The facies associations suggest that sedimentation took place in slope and base-of-slope environments. Two depositional sequences are recognized, separated by a type-1 unconformity. The lower sequence is of Late Neoproterozoic age (units I-IV) and exhibits lowstand, transgressive, and highstand systems tracts. Most of the upper sequence is probably of Early Cambrian age (units V-XII). It begins at the base of unit V and possibly ends with the Tamames Limestone Formation. The upper sequence records a lowstand systems tract and minor-order sea-level oscillations. In the Cambrian units there are higher amounts of feldspar and smaller quantities of intrabasinal clasts than in the Neoproterozoic units. The modal data plot close to the Q-L and Qm-Lt sides of Q-F-L and Qm-F-Lt triangular diagrams, suggesting a provenance from a recycled orogen evolving into a provenance from a craton interior towards the top of the succession. The chemical results, based mainly on Al2O3, TiO2, Zr, and Nb abundances in shales from all the units, strongly suggest a gradual compositional change within this sedimentary succession. Together with the petrological data, the chemical results do not reveal any obvious coeval volcanic contribution to the sediments. On the basis of the chemical data, a comparison is made with other European zones containing detrital sediments composed of reworked crustal components.

Selected Ground-Water Data for Yucca Mountain Region, Southern Nevada and Eastern California, Through December 1999

DTIC Science & Technology

2001-01-01

R, Robison and others (1988); T, Thordarson and others (1967). Contributing units: Saturated lithologic interval yielding water to well: C...13. McKinley and others (1991) describe the contributing units for sites J-11, J-12, MV-1, AD-4a, AD-5, AD-6, AD-8, and AM-4. Thordarson and...COLLECTION SITES 9 Contributing units for springs (fig. 1) indicate sources of water discharged at the sites. Winograd and Thordarson (1975, p

Map showing depth to bedrock in the Seattle 30' by 60' Quadrangle, Washington

USGS Publications Warehouse

Yount, J.C.; Dembroff, G.R.; Barats, G.M.

1985-01-01

Bedrock throughout the Seattle quadrangle is presumed to be volcanic rock, conglomerate, Sandstone, or Shale and is Tertiary in age. With the exception of a few reports of age or lithology collected from oil wells (Livingston, 1958), the subsurface information used for this map sheds little light on the nature and distribution of the various Tertiary rocks in the subsurface. It is assumed, on the basis of pronounced lithologic differences in drill holes and widespread unconformable relationships with underlying bedrock units seen in marine seismic reflection profiles, that the deposits overlying bedrock are Quaternary in age, but no direct dating of materials has been done to confirm this assumption.

Lithologic mapping of mafic intrusions in East Greenland using Landsat Thematic Mapper data

NASA Technical Reports Server (NTRS)

Naslund, H. Richard; Birnie, R. W.; Parr, J. T.

1989-01-01

The East Greenland Tertiary Igneous Province contains a variety of intrusive and extrusive rock types. The Skaergaard complex is the most well known of the intrusive centers. Landsat thematic mapping (TM) was used in conjunction with field spectrometer data to map these mafic intrusions. These intrusions are of interest as possible precious metal ore deposits. They are spectrally distinct from the surrounding Precambrian gneisses. However, subpixel contamination by snow, oxide surface coatings, lichen cover and severe topography limit the discrimination of lithologic units within the gabbro. Imagery of the Skaergaard and surrounding vicinity, and image processing and enhancement techniques are presented. Student theses and other publications resulting from this work are also listed.

Mobility of rare earth elements in mine drainage: Influence of iron oxides, carbonates, and phosphates.

PubMed

Edahbi, Mohamed; Plante, Benoît; Benzaazoua, Mostafa; Ward, Matthew; Pelletier, Mia

2018-05-01

The geochemical behavior of rare earth elements (REE) was investigated using weathering cells. The influence of sorption and precipitation on dissolved REE mobility and fractionation is evaluated using synthetic iron-oxides, carbonates, and phosphates. Sorption cell tests are conducted on the main lithologies of the expected waste rocks from the Montviel deposit. The sorbed materials are characterized using a scanning electron microscope (SEM) equipped with a microanalysis system (energy dispersive spectroscopy EDS) (SEM-EDS), X-ray diffraction (XRD), and X-ray absorption near edge structure (XANES) in order to understand the effect of the synthetic minerals on REE mobility. The results confirm that sorption and precipitation control the mobility and fractionation of REE. The main sorbent phases are the carbonates, phosphates (present as accessory minerals in the Montviel waste rocks), and iron oxides (main secondary minerals generated upon weathering of the Montviel lithologies). The XANES results show that REE are present as trivalent species after weathering. Thermodynamic equilibrium calculations results using Visual Minteq suggest that REE could precipitate as secondary phosphates (REEPO 4 ). Copyright © 2018 Elsevier Ltd. All rights reserved.

[Prediction of regional soil quality based on mutual information theory integrated with decision tree algorithm].

PubMed

Lin, Fen-Fang; Wang, Ke; Yang, Ning; Yan, Shi-Guang; Zheng, Xin-Yu

2012-02-01

In this paper, some main factors such as soil type, land use pattern, lithology type, topography, road, and industry type that affect soil quality were used to precisely obtain the spatial distribution characteristics of regional soil quality, mutual information theory was adopted to select the main environmental factors, and decision tree algorithm See 5.0 was applied to predict the grade of regional soil quality. The main factors affecting regional soil quality were soil type, land use, lithology type, distance to town, distance to water area, altitude, distance to road, and distance to industrial land. The prediction accuracy of the decision tree model with the variables selected by mutual information was obviously higher than that of the model with all variables, and, for the former model, whether of decision tree or of decision rule, its prediction accuracy was all higher than 80%. Based on the continuous and categorical data, the method of mutual information theory integrated with decision tree could not only reduce the number of input parameters for decision tree algorithm, but also predict and assess regional soil quality effectively.

Tectonic geomorphology of the Safeen Anticline (Northern Iraq)

NASA Astrophysics Data System (ADS)

Bartl, N.; Grasemann, B.; Faber, R.; Lockhart, D.

2009-04-01

The Zagros Fold- and Thrust Belt extends over 1800 km from Kurdistan in N-Iraq to the Strait of Hormuz in Iran and is one of the world most promising regions for the future hydrocarbon exploration. The Zagros Mountains are the result of the collision of the Eurasian and the Arabian Plates starting in the Late Cretaceous. Recent GPS measurements in have shown that the shortening between these two plates is about 2.5 cm/a most of which is distributed within the Zagros collision orogen. Whereas the tectonic structure and the geomorphological response to active deformation is thoroughly studied in the SE part of the Zagros in Iran, there are almost no modern field based studies of the NW part of the Zagros in Iraq. Here we present the first structural field studies, the mechanical stratigraphy and geomorphological investigations of the Safeen anticline in the NE of the city of Erbil in the Kurdistan region, which is a province of Northern Iraq. The sub-cylindrical part of the anticline strikes for about 65 km NW-SE and has a dominant wavelength of about 6 km. Perpendicular to the strike of the anticline Cretaceous to Tertiary sediments are exposed consisting mainly of bedded to massif limestones and sandstones (competent lithologies), intercalated with marl and claystones (incompetent lithologies). Whereas deformation in the competent lithologies is accommodated by diffusive mass transfer processes and mainly fracturing, the incompetent lithologies record distributed plastic deformation. Along the investigated section, the limbs of the anticline dip with 55° towards NE (backlimb) and 60° towards SW (forelimb). Interestingly the drainage pattern of the forelimb differs significantly to the erosional signature along the backlimb. Both limbs are dominated by transverse river segments. The backlimb records straight almost perpendicular to the fold axis with a spacing of the segments of about 200 m. The forelimb, however, is dominated by a more irregular pattern with a wider spacing of the main segments of about 600m. We use an ASTER digital elevation model in combination with the geological map in order to quantify the differences in geomorphological signal along the different limbs of the Safeen anticline.

Determining the depositional pattern by resistivity-seismic inversion for the aquifer system of Maira area, Pakistan.

PubMed

Akhter, Gulraiz; Farid, Asim; Ahmad, Zulfiqar

2012-01-01

Velocity and density measured in a well are crucial for synthetic seismic generation which is, in turn, a key to interpreting real seismic amplitude in terms of lithology, porosity and fluid content. Investigations made in the water wells usually consist of spontaneous potential, resistivity long and short normal, point resistivity and gamma ray logs. The sonic logs are not available because these are usually run in the wells drilled for hydrocarbons. To generate the synthetic seismograms, sonic and density logs are required, which are useful to precisely mark the lithology contacts and formation tops. An attempt has been made to interpret the subsurface soil of the aquifer system by means of resistivity to seismic inversion. For this purpose, resistivity logs and surface resistivity sounding were used and the resistivity logs were converted to sonic logs whereas surface resistivity sounding data transformed into seismic curves. The converted sonic logs and the surface seismic curves were then used to generate synthetic seismograms. With the utilization of these synthetic seismograms, pseudo-seismic sections have been developed. Subsurface lithologies encountered in wells exhibit different velocities and densities. The reflection patterns were marked by using amplitude standout, character and coherence. These pseudo-seismic sections were later tied to well synthetics and lithologs. In this way, a lithology section was created for the alluvial fill. The cross-section suggested that the eastern portion of the studied area mainly consisted of sandy fill and the western portion constituted clayey part. This can be attributed to the depositional environment by the Indus and the Kabul Rivers.

Lithologic influences on groundwater recharge through incised glacial till from profile to regional scales: Evidence from glaciated Eastern Nebraska

USGS Publications Warehouse

Gates, John B.; Steele, Gregory V.; Nasta, Paolo; Szilagyi, Jozsef

2014-01-01

Variability in sediment hydraulic properties associated with landscape depositional and erosional features can influence groundwater recharge processes by affecting soil-water storage and transmission. This study considers recharge to aquifers underlying river-incised glaciated terrain where the distribution of clay-rich till is largely intact in upland locations but has been removed by alluvial erosion in stream valleys. In a stream-dissected glacial region in eastern Nebraska (Great Plains region of the United States), recharge estimates were developed for nested profile, aquifer, and regional scales using unsaturated zone profile measurements (matric potentials, Cl- and 3H), groundwater tracers (CFC-12 and SF6), and a remote sensing-assisted water balance model. Results show a consistent influence of till lithology on recharge rates across nested spatial scales despite substantial uncertainty in all recharge estimation methods, suggesting that minimal diffuse recharge occurs through upland glacial till lithology whereas diffuse recharge occurs in river valleys where till is locally absent. Diffuse recharge is estimated to account for a maximum of 61% of total recharge based on comparison of diffuse recharge estimated from the unsaturated zone (0-43 mm yr-1) and total recharge estimated from groundwater tracers (median 58 mm yr-1) and water balance modeling (median 56 mm yr-1). The results underscore the importance of lithologic controls on the distributions of both recharge rates and mechanisms.

Soil nutrients and stoichiometric ratios as affected by land use and lithology at county scale in a karst area, southwest China.

PubMed

Wang, Miaomiao; Chen, Hongsong; Zhang, Wei; Wang, Kelin

2018-04-01

Soil carbon (C), nitrogen (N), and phosphorus (P) are the main soil nutrients required for plant development and their stoichiometric ratios are important indicators of ecosystem functions. However, there have been few studies on the effects of land use and lithology on soil nutrients and stoichiometric ratios, especially in karst areas with extremely fragile geology and intensive human disturbance. To evaluate the synergistic effect of land use and lithology, soil samples at depth of 0-15cm were collected from five land-use types (arable land, plantation forest, grassland, shrubland, and secondary forest) over three lithologies (karst dolomite and limestone and non-karst clasolite) in a typical karst area in southwest China. For natural succession, grassland, shrubland, and secondary forest corresponded to the early, middle, and late successional stage after agricultural abandonment, while from arable land to plantation forest can be treated as a manual reversion after agricultural abandonment. The results showed that, in dolomite, soil organic C (SOC) and total N (TN) increased continuously with natural succession and increased in plantation forest compared to arable land. Total P (TP) continued to decrease from arable land to grassland and then to shrubland. In limestone, SOC and TN did not follow the same pattern because SOC and TN were slightly higher in grassland than shrubland, while TN was slightly lower in plantation forest compared to arable land. TP was remarkably higher in arable land than the other land-use types. For clasolite, SOC was highest in grassland, while TN was not significantly different among land-use types. Compared to arable land, TP was lower in other types of land use. These soil nutrient characteristics led to various stoichiometric ratios under the five land-use types over different lithologies. Therefore, ecological restoration projects based on land use conversion should consider differences in regional lithology and human disturbance. Copyright © 2017 Elsevier B.V. All rights reserved.

Soil nutrient-landscape relationships in a lowland tropical rainforest in Panama

USGS Publications Warehouse

Barthold, F.K.; Stallard, R.F.; Elsenbeer, H.

2008-01-01

Soils play a crucial role in biogeochemical cycles as spatially distributed sources and sinks of nutrients. Any spatial patterns depend on soil forming processes, our understanding of which is still limited, especially in regards to tropical rainforests. The objective of our study was to investigate the effects of landscape properties, with an emphasis on the geometry of the land surface, on the spatial heterogeneity of soil chemical properties, and to test the suitability of soil-landscape modeling as an appropriate technique to predict the spatial variability of exchangeable K and Mg in a humid tropical forest in Panama. We used a design-based, stratified sampling scheme to collect soil samples at 108 sites on Barro Colorado Island, Panama. Stratifying variables are lithology, vegetation and topography. Topographic variables were generated from high-resolution digital elevation models with a grid size of 5 m. We took samples from five depths down to 1 m, and analyzed for total and exchangeable K and Mg. We used simple explorative data analysis techniques to elucidate the importance of lithology for soil total and exchangeable K and Mg. Classification and Regression Trees (CART) were adopted to investigate importance of topography, lithology and vegetation for the spatial distribution of exchangeable K and Mg and with the intention to develop models that regionalize the point observations using digital terrain data as explanatory variables. Our results suggest that topography and vegetation do not control the spatial distribution of the selected soil chemical properties at a landscape scale and lithology is important to some degree. Exchangeable K is distributed equally across the study area indicating that other than landscape processes, e.g. biogeochemical processes, are responsible for its spatial distribution. Lithology contributes to the spatial variation of exchangeable Mg but controlling variables could not be detected. The spatial variation of soil total K and Mg is mainly influenced by lithology. ?? 2007 Elsevier B.V. All rights reserved.

Geochemistry of surface-waters in mineralized and non-mineralized areas of the Yukon-Tanana Uplands

USGS Publications Warehouse

Wang, B.; Wanty, R.B.; Vohden, J.

2005-01-01

The U.S. Geological Survey (USGS) and Alaska Department of Natural Resources (ADNR) are continuing investigations on element mobility in mineralized and non-mineralized areas of the Yukon-Tanana Upland in east-central Alaska. The chemistry of stream water is evaluated in the context of regional bedrock geology and geologic structure. Sampling sites were located in the Big Delta B2 quadrangle, which includes the mineralized areas of the Pogo claim block. The area is typified by steep, subarctic-alpine, boreal forest catchment basins. Samples were collected from catchments that either cross structural features and lithologic contacts, or are underlain by a single lithology. Waters are generally dilute (< 213 mg/L TDS), and are classified as Ca2+ and Mg2+-HCO3- to Ca2+ and Mg2+-SO42- waters. Gneissic lithologies are more SO42- dominated than the intrusive units. The major-ion chemistry of the waters reflects a rock-dominated aqueous system. Trace-element concentrations in water are generally low; however, As and Sb are detected near mineralized areas but in most cases rapidly attenuated downstream and processes other than simple dilution are controlling the concentrations of these trace elements. There is a tendency toward increasing SO42- concentrations downstream in waters both proximal and distal to mineralized areas. More work is necessary to determine what proportion of the increase in SO42- could be derived from the oxidation of sulfide minerals as opposed to water influenced by the underlying gneissic units.

Alternatives for the source of the exotic green clasts from Moldavian Nappes (East Carpathians, Romania)

NASA Astrophysics Data System (ADS)

Tatu, M.

2009-04-01

Important segment of the Carpathian chain, the East Carpathians consists of several tectonic units build up during the Mesozoic and Cenozoic closure of the Tethyan Ocean. These tectonic units are composed by crystalline basements and sedimentary covers, or only by sedimentary piles and they represent a result of two compressional phases of Alpine orogenesis: one during Late Cretaceous that was responsible for thrusting of Central East Carpathian Nappes and Outher Dacian Nappes, and a second phase during Early and Middle Miocene interval that involved the Moldavian Nappes as the external nappes (Sandulescu, 1988). The Moldavian Nappes consist of cover nappes tectonically detached from the basement upon which it was deposited. From inside towards outside several units occur: Convolute Flysch Nappe, Macla Nappe, Audia Nappe, Tarcau Nappe, Marginal Folds Nappe and Subcarpathian Nappe (Sãndulescu et al., 1981). If the internal units (up to Audia Nappe) are represented by the Cretaceous sediment piles, in the external units, especially in the Tarcau Nappe and also in the Marginal Folds Nappe the lithology is dominated by the Paleogene deposits, especially by the Oligocene formations. The most particular for these units are the presence of heterogeneous composition induced by the wildflysch type sedimentation. Previous researchers have considered the piles of the both units as flyschoid deposits, and for a minor central part (Slon Facies) they accepted a wildflysch scenario. Based on our field studies between Prahova valley (Romania) and Tisa upper stream basin (Ukraine), the different sedimentary strata (the Oligocene Tarcau, Fusaru, Kliwa sandstones, dysodilic and menilitic rocks, polymictic conglomerates, marls and argillaceous deposits together with Upper Cretaceous polymictic conglomerates and green-reddish argillaceous deposits) are tectonically mixed during the late-Oligocene - Middle Miocene events. The mechanism of sedimentary mélange is supposed to be related to submarine landslide initiated by huge earthquake activity. In this way the velocity of landslide sedimentation was high and as result the spatial distribution of different rock types is inhomogeneous. On the other hand, high velocity of syn-sedimentary deformation generates synchronous shear zones. The stress field in this environment is influenced by the lithological amalgamation and local discontinuities. After sedimentary deposition and syn - deformation processes in all the area, suborizontal shear zones (SSZ) are formed along the borders of sandstone olistoliths embedded in fine-grained sand-argillaceous sediments; they are related to the Miocene tectogenesis. Taking into account that are not lithological differences in the Tarcau and the Marginal Folds units, the contact between them as all major SSZ represent the intra-formational thrusts (Sandulescu, 1984). An important characteristic of the Moldavian Nappes is the presence of the exotic rocks as clasts in conglomerates that are very different in nature (igneous, metamorphic and sedimentary), volume and size and generally green in colour. Many authors who studied this lithological aspect have suggested that a Cumanian ridge was their source. The ridge was active since Upper Creataceous till Miocene widespread from Central Dobrogea to Poland and mainly composed by "dobrogean green schist" rocks. This ridge was placed between Audia and Macla sedimentation areas, or between Audia and Tarcau sedimentation areas. According to our studies, the green clasts from various conglomerates with igneous (intrusive and extrusive aspects), metamorphic (medium to low grade) and sedimentary nature present a variable participation. The green clasts are apparently similar with the central dobrogean green schist rocks and are less than 10% in participation in all Moldavian units. For this reason we suggest that the Central Dobrogean domain wasn't the source area for the discussed clasts. After Oszczypko (2006), in the Polish Carpathians, between the Magura and Silesian basins during the Upper Cretaceous - Miocene interval the Silesian Ridge was active. Probably, the same structure was active from Polish Carpathians to the south-western end of Romanian East Carpathians also responsible for the presence of the exotic pebbles from external units of East Carpathians. Isotopic ages of exotic clasts from Polish Carpathian Flysch display the values characteristics for the late Neoproterozoic-Cambrian and the late Carboniferous - Permian intervals (Poprawa et al., 2004) which may suggests that the active ridge was a part of the Tornquist - Teisseyre Zone exhumation. Refernces Oszczypko N. 2006. Geol. Quart., 50 (1): 169-194. Poprawa P., Malata T., Pécskay Z., Bana? M., Skulich J., Paszkowski M., Kusiak M. 2004. Min. Soc. Pol. - Spec. Papers, 24: 329-332. Sandulescu M. 1984. Ed. Tehnica, Bucuresti, 336 Sandulescu, M. 1988. AAPG Memoir, vol. 45, pp. 17- 25.

Geologic framework of oil and gas genesis in main sedimentary basins from Romania Oprea Dicea

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ionescu, N.; Morariu, C.D.

1991-03-01

Oil and gas fields located in Moldavic nappes are encompassed in Oligocene and lower Miocene formations, mostly in the marginal folds nappe, where Kliwa Sandstone sequences have high porosity, and in the Black Sea Plateau. The origin of the hydrocarbon accumulations from the Carpathian foredeep seems to be connected to the Oligocene-lower Miocene bituminous formations of the marginal folds and sub-Carpathian nappes. In the Gethic depression, the hydrocarbon accumulations originate in Oligocene and Miocene source rocks and host in structural, stratigraphical, and lithological traps. The accumulations connected with tectonic lines that outline the areal extension of the Oligocene, Miocene, andmore » Pliocene formations are in the underthrusted Moesian platform. The hydrocarbon accumulations related to the Carpathian foreland represent about 40% of all known accumulations in Romania. Most of them are located in the Moesian platform. In this unit, the oil and gas fields present a vertical distribution at different stratigraphic levels, from paleozoic to Neogene, and in all types of reservoirs, suggesting multicycles of oleogenesis, migration, accumulation, and sealing conditions. The hydrocarbon deposits known so far on the Black Sea continental plateau are confined in the Albian, Cenomanian, Turonian-Senonian, and Eocene formations. The traps are of complex type structural, lithologic, and stratigraphic. The reservoirs are sandstones, calcareous sandstones, limestones, and sands. The hydrocarbon source rocks are pelitic and siltic Oligocene formations. Other older source rocks are probably Cretaceous.« less

Using Geophysics to Define Hydrostratigraphic Units in the Edwards and Trinity Aquifers, Texas

NASA Astrophysics Data System (ADS)

Smith, B. D.; Blome, C. D.; Clark, A. K.; Kress, W.; Smith, D. V.

2007-05-01

Airborne and ground geophysical surveys conducted in Uvalde, Medina, and northern Bexar counties, Texas, can be used to define and characterize hydrostratigraphic units of the Edwards and Trinity aquifers. Airborne magnetic surveys have defined numerous Cretaceous intrusive stocks and laccoliths, mainly in Uvalde County, that influence local hydrology and perhaps regional ground-water flow paths. Depositional environments in the aquifers can be classified as shallow water platforms (San Marcos Platform, Edwards Group), shoal and reef facies (Devils River Trend, Devils River Formation), and deeper water basins (Maverick Basin, West Nueces, McKnight, and Salmon Peak Formations). Detailed airborne and ground electromagnetic surveys have been conducted over the Edwards aquifer catchment zone (exposed Trinity aquifer rocks), recharge zone (exposed Edwards aquifer rocks), and artesian zone (confined Edwards) in the Seco Creek area (northeast Uvalde and Medina Counties; Devils River Trend). These geophysical survey data have been used to divide the Edwards exposed within the Balcones fault zone into upper and lower hydrostratigraphic units. Although both units are high electrical resistivity, the upper unit has slightly lower resistivity than the lower unit. The Georgetown Formation, at the top of the Edwards Group has a moderate resistivity. The formations that comprise the upper confining units to the Edwards aquifer rocks have varying resistivities. The Eagleford and Del Rio Groups (mainly clays) have very low resistivities and are excellent electrical marker beds in the Seco Creek area. The Buda Limestone is characterized by high resistivities. Moderate resistivities characterize the Austin Group rocks (mainly chalk). The older Trinity aquifer, underlying the Edwards aquifer rocks, is characterized by less limestone (electrically resistive or low conductivity units) and greater quantities of mudstones (electrically conductive or low resistivity units). In the western area (Devils River Trend and Maverick Basin) of the Trinity aquifer system there are well-defined collapse units and features that are marked by moderate resistivities bracketed by resistive limestone and conductive mudstone of the Glen Rose Limestone. In the central part of the aquifer (San Marcos Platform) the Trinity's lithologies are divided into upper and lower units with further subdivisions into hydrostratigraphic units. These hydrostratigraphic units are well mapped by an airborne electromagnetic survey in Bexar County. Electrical properties of the Edwards aquifer also vary across the fresh-saline water interface where ground and borehole electrical surveys have been conducted. The saline- saturated Edwards is predictably more conductive than the fresh-water saturated rocks. Similar fresh-saline water interfaces exist within the upper confining units of the Edwards aquifer (Carrizo-Wilcox aquifer) and the Trinity aquifer rocks.

The influence of spatial variability of lithological and morphometric characters on drainage network arrangement

NASA Astrophysics Data System (ADS)

Coco, Laura; Buccolini, Marcello

2015-04-01

Several factors control the spatial setting and temporal development of the drainage systems: climate, sea level changes, lithology, tectonics, morphometry, land use and land cover. The present work deals with the role of spatial variability of lithology and morphometry on drainage networks arrangement and presents some preliminary evaluations. The test area was the Periadriatic belt of central Italy, composed of Plio-Pleistocene foredeep succession (clay, sands and conglomerate) arranged in a northeastern vergence monocline. We analyzed 37 small basins directly flowing in the Adriatic Sea (18 in Abruzzi and 19 in Marche Region) that have homogenous climatic, eustatic, tectonic, land use and land cover features. For this reason, we could focus our research on lithology and morphometry. We used 10 m cell-size Italian DEM (TINITALY) supplying by INGV (National Institute of Geophysics and Volcanology) [from http://tinitaly.pi.ingv.it/] as source of morphometric data, and extracted watersheds and stream networks through an automatic procedure included in TauDEM toolbox within ArcGIS 9.3 [freely downloaded from http://hydrology.usu.edu/taudem/taudem5/index.html]. For each drainage basin, we reconstructed the topography prior to the inception of fluvial incision through the Topo-to-Raster interpolation tool, considering the heights of the watershed divide as elevation points and obtaining the pre-incision DEM in which the fluvial valleys resulted filled. On this DEM, we calculated the Morphometric Slope Index (MSI), developed by Buccolini et al. (2012), using the formula M SI = Rc -L -Ar/A2D in which Rc is circularity ratio, L is slope length, A2D and Ar are plane and surface area, respectively. In particular, Ar represents the three-dimensional area calculated on the pre-incision DEM. This index is a unique reference index for basin morphometry including both areal and linear features, such as size, shape, inclination, length and width. As drainage network parameter we calculated drainage density (D) computed by the ratio between total drainage length and basin area. We used National and Regional Geological Map as source of lithological characters. The data were analyzed via statistics in terms of average trend and fluctuations. We split the basins into two groups according to the prevalent lithology. The first group included the basins prevalently made up of clays and sandy clays, the second includes the ones mainly constituted by conglomerates on surface. A Regression Analysis revealed that the influence of MSI on D was driven by the lithology. Indeed, we individuated two logarithmic trends of the MSI-D interpolators corresponding to the lithological groups. This finding demonstrated the great influence of lithology not only on D and MSI, but especially on their relation, depending on the different lithotechnical properties of the lithologies under study. Further enhancements will focus on evaluating the influence of spatial variability of lithology and morphology on the evolution of the current drainage network. We intend to investigate the future development of the fluvial dynamic starting from the current DEM (instead of the pre-incision one) and considering other variables that are generally deemed as drivers of the fluvial dynamic (e.g. land use, land cover).

The impact of mixing lithologies in clast shape measurements on its discriminatory power - a case study from a temperate Alpine glacier

NASA Astrophysics Data System (ADS)

Lukas, S.; Coray, S.; Graf, A.; Schlüchter, C.

2009-04-01

Clast shape measurements have become a standard tool in the reconstruction of transport histories in a variety of depositional settings (Demir et al., 2009). In glacial environments, the combined use of clast form and roundness has become an established tool in the past 15 years or so, and environments where this tool has been used range from temperate and polythermal to cold-based glaciers. In addition, the method has been transferred to palaeo-environments where the knowledge gained in aforementioned studies has taken the degree of accuracy in sedimentological investigations to a higher level (cf. Lukas et al., 2009, and references therein). All of these studies use the approach originally advocated by Benn and Ballantyne (1994), but perhaps the most notable difference is that some researchers mix different lithologies within their samples of 50 clasts. However, the role of lithology on clast shape in a glacial environment has never been systematically analysed, except for one pilot study (Bennett et al., 1997). Likewise, some previous studies have highlighted the problem of distinguishing between fluvial and subglacially-transported clasts using co-variance plots, and thus, more work is needed in both these respects. We here present a set of clast shape data gathered from the foreland and surrounding slopes of temperate Findelengletscher, Switzerland, to (a) test the versatility of clast shape in distinguishing of populations of clasts transported along different paths and (b) assess the role of lithology on the discriminatory potential of the method, most notably using co-variance plots. The main result of this pilot study is that the sampled lithology has a marked effect on clast shape results within the same control group. This is manifest in an overlap of envelopes in both RA- or RWR-C40-covariance plots. If kept separate, all three lithologies display separate control envelopes, in this case in RWR-C40-co-variance plots, thus keeping their discriminatory power. Therefore, at each locality 50 clasts of the same lithology should be measured to allow a clear distinction of different transport paths. References Benn DI, Ballantyne CK. 1994. Reconstructing the transport history of glacigenic sediments: a new approach based on the co-variance of clast shape indices. Sedimentary Geology 91: 215-227. Bennett MR, Hambrey MJ, Huddart D. 1997. Modification of clast shape in high-arctic glacial environments. Journal of Sedimentary Research 67(3): 550-559. Demir T, Lukas S, Warburton J, Bridgland DR. 2009. A review of clast shape analysis. In: Bridgland DR. (ed). Clast lithological analysis. Technical Guide. Quaternary Research Association: London, in press. Lukas S, Coray S, Graf A, Schlüchter S. 2009. The influence of clast lithology and fluvial reworking on the reliability of clast shape measurements in glacial environments - a case study from a temperate Alpine glacier. In: Bridgland DR. (ed). Clast lithological analysis. Technical Guide. Quaternary Research Association: London, in press.

Geophysical framework of the southwestern Nevada volcanic field and hydrogeologic implications

USGS Publications Warehouse

Grauch, V.J.; Sawyer, David A.; Fridrich, Chris J.; Hudson, Mark R.

1999-01-01

Gravity and magnetic data, when integrated with other geophysical, geological, and rock-property data, provide a regional framework to view the subsurface geology in the southwestern Nevada volcanic field. The region has been loosely divided into six domains based on structural style and overall geophysical character. For each domain, the subsurface tectonic and magmatic features that have been inferred or interpreted from previous geophysical work has been reviewed. Where possible, abrupt changes in geophysical fields as evidence for potential structural lithologic control on ground-water flow has been noted. Inferred lithology is used to suggest associated hydrogeologic units in the subsurface. The resulting framework provides a basis for investigators to develop hypotheses from regional ground-water pathways where no drill-hole information exists.

Some aspects of geological information contained in LANDSAT images

NASA Technical Reports Server (NTRS)

Dejesusparada, N. (Principal Investigator); Liu, C. C.; Vitorello, I.; Meneses, P. R.

1980-01-01

The characteristics of MSS images and methods of interpretation are analyzed from a geological point of view. The supportive role of LANDSAT data are illustrated in several examples of surface expressions of geological features, such as synclines and anticlines, spectral characteristics of lithologic units, and circular impact structures.

A model of precambrian geology of Kansas derived from gravity and magnetic data

NASA Astrophysics Data System (ADS)

Xia, Jianghai; Sprowl, Donald R.; Steeples, Don W.

1996-10-01

The fabric of the Precambrian geology of Kansas is revealed through inversion of gravity and magnetic data to pseudo-lithology. There are five main steps in the inversion process: (1) reduction of potential-field data to a horizontal plane in the wavenumber domain; (2) separation of the residual anomaly of interest from the regional background, where an assumption is made that the regional anomaly could be represented by some order of polynomial; (3) subtraction of the signal due to the known topography on the Phanerozoic/Precambrian boundary from the residual anomaly (we assume what is left at this stage are the signals due to lateral variation in the Precambrian lithology); (4) inversion of the residual anomaly in the wavenumber domain to density and magnetization distribution in the top part of the Precambrian constrained by the known geologic information; (5) derivation of pseudo-lithology by characterization of density and magnetization. The boundary between the older Central Plains Province to the north and the Southern Granite-Rhyolite Province to the south is clearly delineated. The Midcontinent Rift System appears to widen in central Kansas and involve a considerable portion of southern Kansas. Lithologies in southwestern Kansas appear to change over fairly small areas and include mafic rocks which have not been encountered in drill holes. The texture of the potential field data from southwestern Kansas suggests a history of continental growth by broad extension.

Stratigraphy of the cambo-ordovician succession in Illnois

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lasemi, Yaghoob; Khorasgani, Zohreh; Leetaru, Hannes

2014-09-30

The Upper Cambrian through Lower Ordovician succession (Sauk II-III sequences) in the Illinois Basin covers the entire state of Illinois and most of the states of Indiana and Kentucky. To determine lateral and vertical lithologic variations of the rocks within the Cambro-Ordovician deposits that could serve as reservoir or seal for CO2 storage, detailed subsurface stratigraphic evaluation of the succession in Illinois was conducted. The Cambro-Ordovician succession in the Illinois Basin consists of mixed carbonate-siliciclastic deposits. Its thickness ranges from nearly 800 feet in the extreme northwest to nearly 8000 feet in the Reelfoot Rift in the extreme southeastern partmore » of the state. In northern and central Illinois, the Cambro-Ordovician rocks are classified as the Cambrian Knox and the Ordovician Prairie du Chien Groups, which consist of alternating dolomite and siliciclastic units. In the southern and deeper part of the Illinois Basin, the Cambro-Ordovician deposits consist chiefly of fine to coarsely crystalline dolomite capped by the Middle Ordovician Everton Formation. Detailed facies analysis indicates that the carbonate units consist mainly of mudstone to grainstone facies (fossiliferous/oolitic limestone and dolomite) with relics of bioclasts, ooids, intraclasts and peloids recording deposition on a shallow marine ramp setting. The dominant lithology of the Knox and the overlying Prairie du Chien Group is fine to coarsely crystalline, dense dolomite. However, porous and permeable vugular or fractured/cavernous dolomite intervals that grade to dense fine to coarsely crystalline dolomite are present within the dolomite units. Several hundred barrels of fluid were lost in some of these porous intervals during drilling, indicating high permeability. The sandstone intervals are porous and permeable and are texturally and compositionally mature. The permeable sandstone and porous dolomite intervals are laterally extensive and could serve as important reservoirs to store natural gas, CO2 or hazardous waste material. Results of this study show that the Cambro-Ordovician Knox Group in the Illinois Basin and adjacent Midwestern regions may be an attractive target for CO2 sequestration because these rocks are 1) laterally extensive, 2) consist of some porous and permeable dolomite and sandstone intervals, and 3) contain abundant impermeable shale and carbonate seals.« less

The Messinian evaporites in the Levant Basin: lithology, deformation and its evolution

NASA Astrophysics Data System (ADS)

Feng, Ye; Steinberg, Josh; Reshef, Moshe

2017-04-01

The lithological composition of the Messinian evaporite in the Levant Basin remains controversial and salt deformation mechanisms are still not fully understood, due to the lack of high resolution 3D depth seismic data and well logs that record the entire evaporite sequence. We demonstrate how 3D Pre-stack depth migration (PSDM) and intra-salt tomography can lead to improved salt imaging. Using 3D PSDM seismic data with great coverage and deepwater well log data from recently drilled boreholes, we reveal intra-salt reflective units associated with thin clastic layers and a seismic transparent background consisting of uniform pure halite. Structural maps of all internal reflectors are generated for stratigraphy and attributes analysis. High amplitude fan structures in the lowermost intra-salt reflector are observed, which may indicate the source of the clastic formation during the Messinian Salinity Crisis (MSC). The Messinian evaporite in the Levant Basin comprises six units; the uppermost unit thickens towards the northwest, whereas the other units are uniform in thickness. The top of salt (TS) horizon is relatively horizontal, while all other intra-salt reflectors and base of salt (BS) dip towards the northwest. Different seismic attributes are used for identification of intra-salt deformation patterns. Maximum curvature maps show NW-striking thrust faults on the TS and upper intra-salt units, and dip azimuth maps are used to show different fold orientations between the TS and intra-salt units, which indicate a two-phase deformation mechanism: basin NW tilting as syn-depositional phase and NNE spreading of Plio-Pleistocene overburden as post-depositional phase. RMS amplitude maps are used to identify a channelized system on the TS. An evaporite evolution model during the MSC of the Levant Basin is therefore established based on all the observations. Finally the mechanical properties of the salts will be utilized to explore salt deformation in the Levant Basin. Feng, Y. E., & Reshef, M. (2016). The Eastern Mediterranean Messinian salt-depth imaging and velocity analysis considerations. Petroleum Geoscience, 22(4), 2-19. doi:http://dx.doi.org/10.1144/petgeo2015-088 Feng, Y. E., Yankelzon, A., Steinberg, J., & Reshef, M. (2016). Lithology and characteristics of the Messinian evaporite sequence of the deep Levant Basin, eastern Mediterranean. Marine Geology, 376, 118-131. doi:http://dx.doi.org/10.1016/j.margeo.2016.04.004

Overview of Hole GT2A: Drilling middle gabbro in Wadi Tayin massif, Oman ophiolite

NASA Astrophysics Data System (ADS)

Takazawa, E.; Kelemen, P. B.; Teagle, D. A. H.; Coggon, J. A.; Harris, M.; Matter, J. M.; Michibayashi, K.

2017-12-01

Hole GT2A (UTM: 40Q 655960.7E / 2529193.5N) was drilled by the Oman Drilling Project (OmDP) into Wadi Gideah of Wadi Tayin massif in the Samail ophiolite, Oman. OmDP is an international collaboration supported by the International Continental Scientific Drilling Program, the Deep Carbon Observatory, NSF, IODP, JAMSTEC, and the European, Japanese, German and Swiss Science Foundations, with in-kind support in Oman from the Ministry of Regional Municipalities and Water Resources, Public Authority of Mining, Sultan Qaboos University, and the German University of Technology. Hole GT2A was diamond cored in 25 Dec 2016 to 18 Jan 2017 to a total depth of 406.77 m. The outer surfaces of the cores were imaged and described on site before being curated, boxed and shipped to the IODP drill ship Chikyu, where they underwent comprehensive visual and instrumental analysis. 33 shipboard scientists were divided into six teams (Igneous, Alteration, Structural, Geochem, Physical Properties, Paleomag) to describe and analyze the cores. Hole GT2A drilled through the transition between foliated and layered gabbro. The transition zone occurs between 50 and 150 m curation corrected depth (CCD). The top 50 m of Hole GT2A is foliated gabbro whereas the bottom 250 m consists of layered gabbro. Brittle fracture is observed throughout the core. Intensity of alteration vein decreases from the top to the bottom of the hole. On the basis of changes in grain size and/or modal abundance and/or appearance/disappearance of igneous primary mineral(s) five lithological units are defined in Hole GT2A (Unit I to V). The uppermost part of Hole GT2A (Unit I) is dominated by fine-grained granular olivine gabbro intercalated with less dominant medium-grained granular olivine gabbro and rare coarse-grained varitextured gabbro. The lower part of the Hole (Units II, III and V) is dominated by medium-grained olivine gabbro, olivine melagabbro and olivine-bearing gabbro. Modally-graded rhythmic layering with olivine melagabbro and olivine-bearing gabbro is well conspicuous in the bottom part of Unit II. The Unit IV occurs between 284.25 m and 293.92 m CCD from the top of the hole and is characterized by orthopyroxene-bearing lithologies such as fine-grained gabbronorite and coarse-grained troctolite. Discrete orthopyroxene crystals occur in these lithologies.

Reinterpretation of the palynology and age of Laramide syntectonic deposits, southwestern Montana, and revision of the Beaverhead Group

NASA Astrophysics Data System (ADS)

Nichols, D. J.; Perry, W. J., Jr.; Haley Johns, J. C.

1985-02-01

New palynological data from syntectonic deposits in southwestern Montana have major temporal implications for Laramide structural relations in the northern Rocky Mountains. Conglomerate and associated sandstones representing the bulk of material eroded from the thrust-faulted margin of the Blacktail-Snowcrest foreland massif are middle Campanian (Aquilapollenites senonicus Interval Zone; estimated absolute age 78 81 Ma). As a major consequence, the foreland buttress responsible for the shape of the southwestern Montana recess of the Cordilleran thrust belt was uplifted and in place by middle Campanian time. Palynomorph assemblages from the Campanian deposits include reworked spores of Paleozoic age that are evidence of provenance. Other less precisely dated syntectonic units in the area differ in age and provenance as well as lithology. Formerly, all these deposits were assigned to the Beaverhead Formation, which is raised to group status herein. The stratigraphic unit shed from the Blacktail-Snowcrest uplift is raised to formation status as the Lima Conglomerate. The term “Beaverhead Group” is restricted to the Lima Conglomerate and to contemporaneous and younger conglomeratic units that differ in lithology and probably in provenance; older sandstone units are removed from the Beaverhead Group. Deposits at the original type section of the Beaverhead Formation are not precisely dated but are no older than Campanian and probably no younger than early Maestrichtian.

Seismics-electrics Joint Interpretation in a gypsiferous context.

NASA Astrophysics Data System (ADS)

Marzan, Ignacio; Marti, David; Lobo, Agustin; Alvarez-Marron, Joaquina; Carbonell, Ramon

2016-04-01

The main objective of this study is to improve the geophysical characterization resulting from a shallow 3D high resolution travel-time tomography survey (500x500m). This survey was acquired in Villar de Cañas (Cuenca, Spain) in late 2013 and early 2014. Lithology down to 150 m depth in this site is characterized by endorheic sediments, mainly siltstone and gypsum. After processing the tomography data, the velocity model showed a good correlation with geology models and borehole data except for the siltstone-gypsum transition. The model involves two lithological limits: the "transition layer - massive gypsum layer" (well resolved by a relatively high velocity contrast) and the "siltstone layer - transition layer" (constrained only in the central part of the model by a relatively low velocity contrast). As electrical resistivity is able to characterize shale-gypsum transitions, we complemented the seismic data with results from a collection of 2D ERT surveys, for which we build a new 3D grid with 2 parameters by node: velocity and resistivity. In order to derive a geological interpretation, we apply a statistical classification method (Linear Discriminant Analysis) to the new bi-parametric grid, using reference classes from well logs. This process results on a final 3D lithological model with less ambiguity and thus with a better definition of the two limits under discussion. Our study shows that the integration of seismic and electric methods significantly improves geological characterization in a gypsiferous context.

Prediction of Exploration Target Areas for GEM Deposits in Mogok Stone Tract, Northern Myanmar by Integrating Remote Sensing and Geoscience Data

NASA Astrophysics Data System (ADS)

Oo, Tin Ko

2011-07-01

The Mogok Stone Tract area has long been known for world famous finest ruby since 1597. The Mogok area lies in northern Myanmar and is located at about 205.99km northeast from Mandalay, the second largest city of Myanmar. The Mogok Group of metasedimentary rocks is divided into four units: (1) Wabyudaung Marble, (2) Ayenyeinchantha Calc-silicate, (3) Gwebin Quartzite, and (4) Kabe Gneiss. Igneous rocks in the Mogok area are classified into two units: (1) Kabaing Granite and (2) Pingutaung Leucogranite. The Mogok area has a complex structure involving several folds and faults. Using marbles and calc-silicates as marker horizons, a series of anticline and syncline can be identified such as Mogok syncline, Ongaing anticline, Bawpadan syncline, and Kyatpyin anticline. All the foldings show a low-angle plunge to the south. The main precious stones of the Mogok area are ruby and sapphire; and the other important semi-precious stones are spinel, topaz, peridot, garnet, apatite, beryl, tourmaline (rubellite), quartz, diopside, fluorite, and enstatite. Geological and remote sensing data are processed to extract the indicative features of gem mineralized areas: lithology, structure, and hydrothermal alteration. Density slice version of Landsat ETM band ratios 5/7 is used to map clay alterations. Filtering Landsat ETM band 5 by using edge detection filter is applied for lineament mapping. Spatial integration of various geoscience and remote sensing data sets such as geological maps, Landsat ETM images, and the location map of gem mines show the distribution of alteration zones associated with the gem mineralization in the study area. Geographic Information System (GIS) model has been designed and implemented by ARCVIEW software package based on the overlay of lithologic, lineament, and alteration vector maps. This process has resulted in delineation of most promising areas of probable gem mineralized zones as on the output map.

Outcrop-scale imaging spectroscopy of the Haughton impact structure, Canada

NASA Astrophysics Data System (ADS)

Greenberger, R. N.; Ehlmann, B. L.; Osinski, G. R.; Tornabene, L. L.; Green, R. O.

2016-12-01

Field-portable imaging spectrometers are a novel tool to study heterogeneous deposits such as those found at impact structures. Laboratory imaging spectroscopy of samples from the Haughton impact structure, Devon Island, Nunavut, Canada, detects and maps a variety of minerals within hand samples including calcite, dolomite, hydrated silica, gypsum, garnet, and iron oxides and sulfates. Many of these minerals originate from the target rock lithologies (e.g., limestone, dolostone, sandstone, gneiss) that have been shocked, altered, and displaced. An intimate mixture of quenched melts of calcite and hydrated silica is indicative of the melt rock matrix and is a byproduct of the impact process. Based on these preliminary results, we conducted a field campaign in Summer 2016 at the Haughton structure using imaging spectroscopy on the ground to study and quantify outcrops of impact-disrupted materials around the structure. Key questions addressed include (1) to what extent are the different impact-disrupted/exposed target lithologies from discrete stratigraphic units homogenized during impact processes, (2) what single or mixed lithologies are we able to detect, and (3) is variability within the target lithologies observable within the impactites? The Haughton impact structure is an ideal location to address these questions due to its excellent preservation and the nearly flat-lying, undeformed target rocks. We will present results from the field campaign along with supporting laboratory analyses. The results have implications for our understanding of impact processes and interpretation of planetary remote sensing datasets.

Naturally occurring contaminants in the Piedmont and Blue Ridge crystalline-rock aquifers and Piedmont Early Mesozoic basin siliciclastic-rock aquifers, eastern United States, 1994–2008

USGS Publications Warehouse

Chapman, Melinda J.; Cravotta, Charles A.; Szabo, Zoltan; Lindsay, Bruce D.

2013-01-01

Groundwater quality and aquifer lithologies in the Piedmont and Blue Ridge Physiographic Provinces in the eastern United States vary widely as a result of complex geologic history. Bedrock composition (mineralogy) and geochemical conditions in the aquifer directly affect the occurrence (presence in rock and groundwater) and distribution (concentration and mobility) of potential naturally occurring contaminants, such as arsenic and radionuclides, in drinking water. To evaluate potential relations between aquifer lithology and the spatial distribution of naturally occurring contaminants, the crystalline-rock aquifers of the Piedmont and Blue Ridge Physiographic Provinces and the siliciclastic-rock aquifers of the Early Mesozoic basin of the Piedmont Physiographic Province were divided into 14 lithologic groups, each having from 1 to 16 lithochemical subgroups, based on primary rock type, mineralogy, and weathering potential. Groundwater-quality data collected by the U.S. Geological Survey (USGS) National Water-Quality Assessment (NAWQA) Program from 1994 through 2008 from 346 wells and springs in various hydrogeologic and land-use settings from Georgia through New Jersey were compiled and analyzed for this study. Analyses for most constituents were for filtered samples, and, thus, the compiled data consist largely of dissolved concentrations. Concentrations were compared to criteria for protection of human health, such as U.S. Environmental Protection Agency (USEPA) drinking water maximum contaminant levels and secondary maximum contaminant levels or health-based screening levels developed by the USGS NAWQA Program in cooperation with the USEPA, the New Jersey Department of Environmental Protection, and Oregon Health & Science University. Correlations among constituent concentrations, pH, and oxidation-reduction (redox) conditions were used to infer geochemical controls on constituent mobility within the aquifers. Of the 23 trace-element constituents evaluated, arsenic, manganese, and zinc were detected in one or more water samples at concentrations greater than established human health-based criteria. Arsenic concentrations typically were less than 1 microgram per liter (µg/L) in most groundwater samples; however, concentrations of arsenic greater than 1 µg/L frequently were detected in groundwater from clastic lacustrine sedimentary rocks of the Early Mesozoic basin aquifers and from metamorphosed clastic sedimentary rocks of the Piedmont and Blue Ridge crystalline rock aquifers. Groundwater from these rock units had elevated pH compared to other rock units evaluated in this study. Of the nine samples for which arsenic concentration was greater than 10 µg/L, six were classified as oxic and three as anoxic, and seven had pH of 7.2 or greater. Manganese concentrations typically were less than 10 µg/L in most samples; however, 8.3 percent of samples from the Piedmont and Blue Ridge crystalline-rock aquifers and 3.0 percent of samples from the Early Mesozoic basin siliciclastic rock aquifers had manganese concentrations greater than the 300-µg/L health-based screening level. The positive correlation of manganese with iron and ammonia and the negative correlation of manganese with dissolved oxygen and nitrate are consistent with the reductive dissolution of manganese oxides in the aquifer. Zinc concentrations typically were less than 10 µg/L in the groundwater samples considered in the study, but 0.4 percent and 5.5 percent of the samples had concentrations greater than the health-based screening level of 2,000 µg/L and one-tenth of the health-based screening level, respectively. The mean rank concentration of zinc in groundwater from the quartz-rich sedimentary rock lithologic group was greater than that for other lithologic groups even after eliminating samples collected from wells constructed with galvanized casing. Approximately 90 percent of 275 groundwater samples had radon-222 concentrations that were greater than the proposed alternative maximum contaminant level of 300 picocuries per liter. In contrast, only 2.0 percent of 98 samples had combined radium (radium-226 plus radium-228) concentrations greater than the maximum contaminant level of 5.0 picocuries per liter, and 0.6 percent of 310 samples had uranium concentrations greater than the maximum contaminant level of 30 µg/L. Radon concentrations were highest in the Piedmont and Blue Ridge crystalline-rock aquifers, especially in granite, and elevated median concentrations were noted in the Piedmont Early Mesozoic basin aquifers, but without the extreme maximum concentrations found in the crystalline rocks (granites). Although the siliciclastic lithologies had a greater frequency of elevated uranium concentrations, radon and radium were commonly detected in water from both siliciclastic and crystalline lithologies. Uranium concentrations in groundwater from clastic sedimentary and clastic lacustrine/evaporite sedimentary lithologic groups within the Early Mesozoic basin aquifers, which had median concentrations of 3.6 and 3.1 µg/L, respectively, generally were higher than concentrations for other siliciclastic lithologic groups, which had median concentrations less than 1 µg/L. Although 89 percent of the 260 samples from crystalline-rock aquifers had uranium concentrations less than 1 µg/L, 0.8 percent had uranium concentrations greater than the 30-µg/L maximum contaminant level, and 6.5 percent had concentrations greater than 3 µg/L.

New Insights into the Geology of the Mars Pathfinder Landing Site from Spectral and Morphologic Analysis of the 12-Color Superpan Panorama

NASA Technical Reports Server (NTRS)

Murchie, S.; Barnouin-Jha, O.; Barnouin-Jha, K.; Bishop, J.; Johnson, J.; McSween, H.; Morris, R.

2003-01-01

New analyses of rocks and soils at the Mars Pathfinder landing site have been completed using the full Imager for Mars Pathfinder (IMP) 12- color SuperPan panorama. These revise early conclusions that rocks at the landing site are a single lithology coated only by windblown dust. We conclude instead that there is also a second lithology in addition to the dominant gray rock, and that it is consistent with highlands material excavated from beneath a thin veneer of northern plains; that many rocks have cemented coatings that formed during an early, probably wetter climate; and that young rocks excavated after coating formation ceased are mainly breccias or conglomerates.

3D geological to geophysical modelling and seismic wave propagation simulation: a case study from the Lalor Lake VMS (Volcanogenic Massive Sulphides) mining camp

NASA Astrophysics Data System (ADS)

Miah, Khalid; Bellefleur, Gilles

2014-05-01

The global demand for base metals, uranium and precious metals has been pushing mineral explorations at greater depth. Seismic techniques and surveys have become essential in finding and extracting mineral rich ore bodies, especially for deep VMS mining camps. Geophysical parameters collected from borehole logs and laboratory measurements of core samples provide preliminary information about the nature and type of subsurface lithologic units. Alteration halos formed during the hydrothermal alteration process contain ore bodies, which are of primary interests among geologists and mining industries. It is known that the alteration halos are easier to detect than the ore bodies itself. Many 3D geological models are merely projection of 2D surface geology based on outcrop inspections and geochemical analysis of a small number of core samples collected from the area. Since a large scale 3D multicomponent seismic survey can be prohibitively expensive, performance analysis of such geological models can be helpful in reducing exploration costs. In this abstract, we discussed challenges and constraints encountered in geophysical modelling of ore bodies and surrounding geologic structures from the available coarse 3D geological models of the Lalor Lake mining camp, located in northern Manitoba, Canada. Ore bodies in the Lalor lake VMS camp are rich in gold, zinc, lead and copper, and have an approximate weight of 27 Mt. For better understanding of physical parameters of these known ore bodies and potentially unknown ones at greater depth, we constructed a fine resolution 3D seismic model with dimensions: 2000 m (width), 2000 m (height), and 1500 m (vertical depth). Seismic properties (P-wave, S-wave velocities, and density) were assigned based on a previous rock properties study of the same mining camp. 3D finite-difference elastic wave propagation simulation was performed in the model using appropriate parameters. The generated synthetic 3D seismic data was then compared to the 3D multicomponent field survey data. Main features of the geological models, especially boundaries of main ore bodies were comparable in both data sets. This shows that the 3D geophysical model based on local geology and limited core samples is in fair agreement with the lithologic units confirmed from the field seismic survey data.

Migmatization and low-pressure overprinting metamorphism as record of two pre-Cretaceous tectonic episodes in the Santander Massif of the Andean basement in northern Colombia (NW South America)

NASA Astrophysics Data System (ADS)

Zuluaga, C. A.; Amaya, S.; Urueña, C.; Bernet, M.

2017-03-01

The core of the Santander Massif in the northern Andes of Colombia is dominated by migmatitic gneisses with a < 1.71 Ga protolith and was affected by continuous interactions of oceanic plates to the west and the northwestern corner of the South American continental plate. The exposed metamorphic core of the massif offers a unique opportunity to understand the tectonic evolution of northwestern South America. We present new metamorphic petrology and geochemistry data from the Bucaramanga Gneiss in the Santander Massif to document part of this tectonic evolution from late Proterozoic to Jurassic times. Metapelitic migmatite gneiss, quartz-feldspathic gneiss, and amphibolite from the Bucaramanga Gneiss recorded metamorphic peak conditions in the range of 660-850 °C at pressures of > 7.5 kbar. Lithologies are overprinted by low-pressure metamorphism, related to extensive Jurassic intrusions and linked with growth of cordierite and equilibration of low-pressure mineral assemblages, recorded metamorphic conditions are < 750 °C and < 6.5 kbar. Observed leucosomes display significant compositional variations and can be grouped in three groups: i) Group One leucosomes with high total REE content, high LREE/HREE, and negative Eu anomaly, ii) Group Two leucosomes with low total REE, low LREE/HREE, and positive Eu anomalies, and iii) Group Three leucosomes with relatively low LREE/HREE and strong positive Eu anomaly. Geochemical data support the interpretation that Group Two leucosomes crystallized from melts originated in a partial melting event affecting mostly pelitic and quartz-feldspathic lithologies with fluid-present melting reactions. The evaluation of mesosomes (amphibolite, pelitic and quartz-feldspathic rocks) as potential protoliths or restites indicates that at least two pelitic samples of the analyzed lithologies have characteristics consistent with the occurrence of fluid-present melting reactions involving quartz and feldspar. The leucosomes produced by crystallization of modified partial melts contrast with several other leucosomes that were injected; however, in some cases the melts crystallized as injected leucosomes show consistent geochemistry with partial melting of lithologies geochemically similar to the ones observed in the unit. The migmatization and the low pressure metamorphic overprint are related here to two main tectonic events: an early Paleozoic tectonic pulse produced by subduction of the oceanic crust of the Iapetus Ocean beneath northwestern Gondwana, and an Upper Triassic to Lower Jurassic tectonic pulse produced by subduction of oceanic crust of the proto-Pacific ocean beneath western Pangaea.

Geologic map and map database of parts of Marin, San Francisco, Alameda, Contra Costa, and Sonoma counties, California

USGS Publications Warehouse

Blake, M.C.; Jones, D.L.; Graymer, R.W.; digital database by Soule, Adam

2000-01-01

This digital map database, compiled from previously published and unpublished data, and new mapping by the authors, represents the general distribution of bedrock and surficial deposits in the mapped area. Together with the accompanying text file (mageo.txt, mageo.pdf, or mageo.ps), it provides current information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:62,500 or smaller general distribution of bedrock and surficial deposits in the mapped area. Together with the accompanying text file (mageo.txt, mageo.pdf, or mageo.ps), it provides current information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:62,500 or smaller.

Ordovician "sphinctozoan" sponges from Prince of Wales Island, southeastern Alaska

USGS Publications Warehouse

Rigby, J.K.; Karl, Susan M.; Blodgett, R.B.; Baichtal, J.F.

2005-01-01

A faunule of silicified hypercalcified "sphinctozoan" sponges has been recovered from a clast of Upper Ordovician limestone out of the Early Devonian Karheen Formation on Prince of Wales Island in southeastern Alaska. Included in the faunule are abundant examples of the new genus Girtyocoeliana, represented by Girtyocoeliana epiporata (Rigby and Potter), and Corymbospongia adnata Rigby and Potter, along with rare Corymbospongia amplia n. sp., and Girtyocoelia(?) sp., plus common Amblysiphonella sp. 1 and rare Amblysiphonella(?) sp. 2. The assemblage is similar to that from Ordovician clasts from the eastern Klamath Mountains of northern California. This indicates that the Alexander terrane of southeastern Alaska is related paleogeographically to the lithologically and paleontologically similar terrane of the eastern Klamath Mountains. This lithology and fossil assemblage of the clast cannot be tied to any currently known local rock units on Prince of Wales Island. Other clasts in the conglomerate appear to have been locally derived, so it is inferred that the limestone clasts were also locally derived, indicating the presence of a previously undocumented Ordovician limestone unit on northern Prince of Wales Island. 

Lithologic mapping of the Mordor, NT, Australia ultramafic complex by using the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER)

USGS Publications Warehouse

Rowan, L.C.; Mars, J.C.; Simpson, C.J.

2005-01-01

Spectral measurements made in the Mordor Pound, NT, Australia study area using the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), in the laboratory and in situ show dominantly Al-OH and ferric-iron VNIR-SWIR absorption features in felsic rock spectra and ferrous-iron and Fe,Mg-OH features in the mafic-ultramafic rock spectra. ASTER ratio images, matched-filter, and spectral-angle mapper processing (SAM) were evaluated for mapping the lithologies. Matched-filter processing in which VNIR + SWIR image spectra were used for reference resulted in 4 felsic classes and 4 mafic-ultramafic classes based on Al-OH or Fe,Mg-OH absorption features and, in some, subtle reflectance differences related to differential weathering and vegetation. These results were similar to those obtained by match-filter analysis of HyMap data from a previous study, but the units were more clearly demarcated in the HyMap image. ASTER TIR spectral emittance data and laboratory emissivity measurements document a wide wavelength range of Si-O spectral features, which reflect the lithological diversity of the Mordor ultramafic complex and adjacent rocks. SAM processing of the spectral emittance data distinguished 2 classes representing the mafic-ultramafic rocks and 4 classes comprising the quartzose to intermediate composition rocks. Utilization of the complementary attributes of the spectral reflectance and spectral emittance data resulted in discrimination of 4 mafic-ultramafic categories; 3 categories of alluvial-colluvial deposits; and a significantly more completely mapped quartzite unit than could be accomplished by using either data set alone. ?? 2005 Elsevier Inc. All rights reserved.

Regional geology mapping using satellite-based remote sensing approach in Northern Victoria Land, Antarctica

NASA Astrophysics Data System (ADS)

Pour, Amin Beiranvand; Park, Yongcheol; Park, Tae-Yoon S.; Hong, Jong Kuk; Hashim, Mazlan; Woo, Jusun; Ayoobi, Iman

2018-06-01

Satellite remote sensing imagery is especially useful for geological investigations in Antarctica because of its remoteness and extreme environmental conditions that constrain direct geological survey. The highest percentage of exposed rocks and soils in Antarctica occurs in Northern Victoria Land (NVL). Exposed Rocks in NVL were part of the paleo-Pacific margin of East Gondwana during the Paleozoic time. This investigation provides a satellite-based remote sensing approach for regional geological mapping in the NVL, Antarctica. Landsat-8 and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) datasets were used to extract lithological-structural and mineralogical information. Several spectral-band ratio indices were developed using Landsat-8 and ASTER bands and proposed for Antarctic environments to map spectral signatures of snow/ice, iron oxide/hydroxide minerals, Al-OH-bearing and Fe, Mg-OH and CO3 mineral zones, and quartz-rich felsic and mafic-to-ultramafic lithological units. The spectral-band ratio indices were tested and implemented to Level 1 terrain-corrected (L1T) products of Landsat-8 and ASTER datasets covering the NVL. The surface distribution of the mineral assemblages was mapped using the spectral-band ratio indices and verified by geological expeditions and laboratory analysis. Resultant image maps derived from spectral-band ratio indices that developed in this study are fairly accurate and correspond well with existing geological maps of the NVL. The spectral-band ratio indices developed in this study are especially useful for geological investigations in inaccessible locations and poorly exposed lithological units in Antarctica environments.

The rock components and structures of Archean greenstone belts: An overview

NASA Technical Reports Server (NTRS)

Lowe, D. R.; Byerly, G. R.

1986-01-01

Knowledge of the character and evolution of the Earth's early crust is derived from the studies of the rocks and structures in Archean greenstone belts. Ability to resolve the petrologic, sedimentological and structural histories of greenstone belts, however, hinges first on an ability to apply the concepts and procedures of classical stratigraphy. Unfortunately, early Precambrian greenstone terrains present particular problems to stratigraphic analysis. Many current controversies of greenstone belt petrogenesis, sedimentology, tectonics and evolution arise more from an inability to develop a clear stratigraphic picture of the belts than from ambiguities in interpretation. Four particular stratigraphic problems that afflict studies of Archean greenstone belts are considered: determination of facing directions, correlation of lithologic units, identification of primary lithologies and discrimination of stratigraphic versus structural contacts.

Multiseasonal variables in digital image enhancements for geological applications

NASA Technical Reports Server (NTRS)

Parada, N. D. J. (Principal Investigator); Vitorello, I.; Almeidafilho, R.

1984-01-01

Examples of enhanced multiseasonal orbital imagery illustrate the influence of multiseasonal changes in their spatial and spectral attributes, and consequently in their application to structural geology and lithological discrimination. Shadow effects associated with appropriate solar elevation and azimuth effects enhance the spatial attributes but not the spectral. In this case, variations in illumination conditions should be minimized by selecting images with high solar elevation and by the use of techniques that minimize illumination conditions. Multiseasonal imagery should be used in the identification of spectral contrast changes of rock-soil-vegetation associations which can provide evidences of related lithological units and structural features. The extraction of maximum geological information requires, at least, a fall/winter and a spring/summer scene from which spatial, spectral and multiseasonal attributes can be adequately explored.

Utilizing ERTS-1 imagery for tectonic analysis through study of the Bighorn Mountains region

NASA Technical Reports Server (NTRS)

Hoppin, R. A. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Comparisons of imagery of three seasons, late summer-fall, winter, and spring indicate that for this region fall imagery is the best for overall geologic analysis. Winter scenes with light to moderate snow cover provide excellent topographic detail owing to snow enhancement, lower sun angle, and clarity of the atmosphere. Spring imagery has considerable reduction of tonal contrast owing to the low reflecting heavy green grass cover which subdues lithologic effects; heavy snow cover in the uplands masks topography. Mapping of geologic formations is impractical in most cases. Separation into tonal units can provide some general clues on structure. A given tonal unit can include parts of several geologic formations and different stratigraphic units can have the same tonal signature. Drainage patterns and anomalies provide the most consistent clues for detecting folds, monoclines, and homoclines. Vegetation only locally reflects lithology and structure. False color infrared 9 x 9 transparencies are the most valuable single imagery. Where these can be supplemented by U-2 color infrared for more detailed work, a tremendous amount of information is available. Adequately field checking such a large area just in one scene is the major logistic problem even in a fairly well known region.

GIS-based landslide hazard evaluation at the regional scale: some critical points in the permanent displacement approach for seismically-induced landslide maps

NASA Astrophysics Data System (ADS)

Vessia, Giovanna; Parise, Mario

2013-04-01

Landslide susceptibility and hazard are commonly developed by means of GIS (Geographic Information Systems) tools. Many products such as DTM (Digital Terrain Models), and geological, morphological and lithological layers (often, to be downloaded for free and integrated within GIS) are nowadays available on the web and ready to be used for urban planning purposes. The multiple sources of public information enable the local authorities to use these products for predicting hazards within urban territories by limited investments on technological infrastructures. On the contrary, the necessary expertise required for conducting pertinent hazard analyses is high, and rarely available at the level of the local authorities. In this respect, taking into account the production of seismically-induced landslide hazard maps at regional scale drawn by GIS tool, these can be performed according to the permanent displacement approach derived by Newmark's sliding block method (Newmark, 1965). Some simplified assumptions are considered for occurrence of a seismic mass movement, listed as follows: (1) the Mohr-Coulomb criterion is used for the plastic displacement of the rigid block; (2) only downward movements are accounted for; (3) a translative sliding mechanism is assumed. Under such conditions, several expressions have been proposed for predicting permanent displacements of slopes during seismic events (Ambresys and Menu, 1988; Luzi and Pergalani 2000; Romeo 2000; Jibson 2007, among the others). These formulations have been provided by researchers for different ranges of seismic magnitudes, and for indexes describing the seismic action, such as peak ground acceleration, peak ground velocity, Arias Intensity, and damage potential. With respect to the resistant properties of the rock units, the critical acceleration is the relevant strength variable in every expressions; it is a function of local slope, groundwater level, unit weight shear resistance of the surficial sediments, and the assumed depth of the sliding surface. Thus, it is of paramount relevance to correctly understand and describe the dynamic behavior of the lithologies affected by the earthquake. Accordingly, we put here in evidence some critical points in the application of the permanent displacement formulations by considering the case study of Santa Susana Mountains (California, USA) shaken by the Northridge earthquake in 1994. During this earthquake, a high number of registrations has been collected, whilst soon after a careful inventory of the mass movements triggered by the shaking has been produced, together with analysis of the related failure mechanisms. Hence, these data allow to perform a back analysis in order to verify the reliability of some numerical expressions, such as those proposed by Ambraseys and Menu (1988), Romeo (2000), and Jibson (2007), with respect to the possible dynamic behavior of the lithologies affected by landslides. In this sector of California, the following lithologies crop out, that were involved in shallow landslides: (1) Quaternay deposits; (2) Saugus Formation; (3) Towsley Formation; (4) Pico Formation; (5) Topanga Formation; (6) Modelo Formation; (7) Simi Conglomerate; (8) Santa Susana Formation; (9) Llajas and Chatsworth Formations. The surveys carried out after the Northridge earthquake (Harp and Jibson, 1995), and the analysis of landslide distribution (Parise and Jibson 2000) pointed out that the strongest formations with slopes higher than 50° mainly suffered toppling or fall failures: thus, our hazard maps based on permanent displacements did not take into account such range of slopes. Further, areas with slopes lower than 10° were not affected by relevant mass movements. Thus, a limited range of slopes (between 10° and 45°) was considered in the analyses, with depth of the sliding surface varying between 1 and 3 m, and using the resistance parameters of involved lithologies obtained from in situ and laboratory tests performed by local practitioners. Seismically-induced landslide hazard maps have been drawn using the aforementioned three expressions. The preliminary results show Quaternary deposits (including alluvium deposits, slope wash, and terrace deposits) as the lithologies most affected by permanent displacement. Moreover, Towsley and Modelo formations, that are stiffer than the previous rock units, and consist mostly of shales, siltstones and subordinate sandstones, show high hazard value where the slopes increase. The relevant role of local slope in permanent displacement extent is evident where lithologies are characterized by both cohesive and frictional resistance components. Finally, a comparison among the maps produced by using the three expressions for permanent displacements is discussed. References Ambraseys N.N. and Menu J.M. (1988) Earthquake-induced ground displacements. Earthquake Engineering and Structural Dynamics, 16: 985-1006. Harp E.L. and Jibson R.W. (1995) Inventory of landslides triggered by the 1994 Northridge, California earthquake. US Geol. Surv. Open-File Rep. 95-213 17 pp. Jibson R. (2007) Regression models for estimating coseismic landslide displacement. Engineering Geology, 91: 209-218. Luzi L. and Pergalani F. (2000) A correlation between slope failures and accelerometric parameters: the 26 September 1997 earthquake (Umbria-Marche, Italy). Soil Dynamics and Earthquake Engineering, 20: 301-313. Newmark N.M. (1965) Effects of earthquakes on dams and embankments. Geotechnique 965, 15(2): 139-160. Parise M. and Jibson R.W. (2000) A seismic landslide susceptibility rating of geologic units based on analysis of characteristics of landslides triggered by the 17 January, 1994 Northridge, California earthquake. Engineering Geology, 58: 251-270. Romeo R. (2000) Seismically induced landslide displacements: a predictive model. Engineering Geology, 58: 337-351.

A new multi-scale geomorphological landscape GIS for the Netherlands

NASA Astrophysics Data System (ADS)

Weerts, Henk; Kosian, Menne; Baas, Henk; Smit, Bjorn

2013-04-01

At present, the Cultural Heritage Agency of the Netherlands is developing a nationwide landscape Geographical Information System (GIS). In this new conceptual approach, the Agency puts together several multi-scale landscape classifications in a GIS. The natural physical landscapes lie at the basis of this GIS, because these landscapes provide the natural boundary conditions for anthropogenic. At the local scale a nationwide digital geomorphological GIS is available in the Netherlands. This map, that was originally mapped at 1:50,000 from the late 1970's to the 1990's, is based on geomorphometrical (observable and measurable in the field), geomorphological and, lithological and geochronological criteria. When used at a national scale, the legend of this comprehensive geomorphological map is very complex which hampers use in e.g. planning practice or predictive archaeology. At the national scale several landscape classifications have been in use in the Netherlands since the early 1950's, typically ranging in the order of 10 -15 landscape units for the entire country. A widely used regional predictive archaeological classification has 13 archaeo-landscapes. All these classifications have been defined "top-down" and their actual content and boundaries have only been broadly defined. Thus, these classifications have little or no meaning at a local scale. We have tried to combine the local scale with the national scale. To do so, we first defined national physical geographical regions based on the new 2010 national geological map 1:500,000. We also made sure there was a reference with the European LANMAP2 classification. We arrived at 20 landscape units at the national scale, based on (1) genesis, (2) large-scale geomorphology, (3) lithology of the shallow sub-surface and (4) age. These criteria that were chosen because the genesis of the landscape largely determines its (scale of) morphology and lithology that in turn determine hydrological conditions. All together, they define the natural boundary conditions for anthropogenic use. All units have been defined, mapped and described based on these criteria. This enables the link with the European LANMAP2 GIS. The unit "Till-plateau sand region" for instance runs deep into Germany and even Poland. At the local scale, the boundaries of the national units can be defined and precisely mapped by linking them to the 1:50,000 geomorphological map polygons. Each national unit consists of a typical assemblage of local geomorphological units. So, the newly developed natural physical landscape map layer can be used from the local to the European scale.

Preliminary three-dimensional geohydrologic framework of the San Antonio Creek Groundwater Basin, Santa Barbara County, California

NASA Astrophysics Data System (ADS)

Cromwell, G.; Sweetkind, D. S.; O'leary, D. R.

2017-12-01

The San Antonio Creek Groundwater Basin is a rural agricultural area that is heavily dependent on groundwater to meet local water demands. The U.S. Geological Survey (USGS) is working cooperatively with Santa Barbara County and Vandenberg Air Force Base to assess the quantity and quality of the groundwater resources within the basin. As part of this assessment, an integrated hydrologic model that will help stakeholders to effectively manage the water resources in the basin is being developed. The integrated hydrologic model includes a conceptual model of the subsurface geology consisting of stratigraphy and variations in lithology throughout the basin. The San Antonio Creek Groundwater Basin is a relatively narrow, east-west oriented valley that is structurally controlled by an eastward-plunging syncline. Basin-fill material beneath the valley floor consists of relatively coarse-grained, permeable, marine and non-marine sedimentary deposits, which are underlain by fine-grained, low-permeability, marine sedimentary rocks. To characterize the system, surficial and subsurface geohydrologic data were compiled from geologic maps, existing regional geologic models, and lithology and geophysical logs from boreholes, including two USGS multiple-well sites drilled as part of this study. Geohydrologic unit picks and lithologic variations are incorporated into a three-dimensional framework model of the basin. This basin (model) includes six geohydrologic units that follow the structure and stratigraphy of the area: 1) Bedrock - low-permeability marine sedimentary rocks; 2) Careaga Formation - fine to coarse grained near-shore sandstone; 3) Paso Robles Formation, lower portion - sandy-gravely deposits with clay and limestone; 4) Paso Robles Formation, middle portion - clayey-silty deposits; 5) Paso Robles Formation, upper portion - sandy-gravely deposits; and 6) recent Quaternary deposits. Hydrologic data show that the upper and lower portions of the Paso Robles Formation are the primary grou­ndwater-bearing units within the basin, and that the fine-grained layer within this Formation locally restricts vertical groundwater flow.

Igneous activity, metamorphism, and deformation in the Mount Rogers area of SW Virginia and NW North Carolina: A geologic record of Precambrian tectonic evolution of the southern Blue Ridge Province

USGS Publications Warehouse

Tollo, Richard P.; Aleinikoff, John N.; Mundil, Roland; Southworth, C. Scott; Cosca, Michael A.; Rankin, Douglas W.; Rubin, Allison E.; Kentner, Adrienne; Parendo, Christopher A.; Ray, Molly S.

2012-01-01

Mesoproterozoic basement in the vicinity of Mount Rogers is characterized by considerable lithologic variability, including major map units composed of gneiss, amphibolite, migmatite, meta-quartz monzodiorite and various types of granitoid. SHRIMP U-Pb geochronology and field mapping indicate that basement units define four types of occurrences, including (1) xenoliths of ca. 1.33 to ≥1.18 Ga age, (2) an early magmatic suite including meta-granitoids of ca. 1185–1140 Ma age that enclose or locally intrude the xenoliths, (3) metasedimentary rocks represented by layered granofels and biotite schist whose protoliths were likely deposited on the older meta-granitoids, and (4) a late magmatic suite composed of younger, ca. 1075–1030 Ma intrusive rocks of variable chemical composition that intruded the older rocks. The magmatic protolith of granofels constituting part of a layered, map-scale xenolith crystallized at ca. 1327 Ma, indicating that the lithology represents the oldest, intact crust presently recognized in the southern Appalachians. SHRIMP U-Pb data indicate that periods of regional Mesoproterozoic metamorphism occurred at 1170–1140 and 1070–1020 Ma. The near synchroneity in timing of regional metamorphism and magmatism suggests that magmas were emplaced into crust that was likely at near-solidus temperatures and that melts might have contributed to the regional heat budget. Much of the area is cut by numerous, generally east- to northeast-striking Paleozoic fault zones characterized by variable degrees of ductile deformation and recrystallization. These high-strain fault zones dismember the terrane, resulting in juxtaposition of units and transformation of basement lithologies to quartz- and mica-rich tectonites with protomylonitic and mylonitic textures. Mineral assemblages developed within such zones indicate that deformation and recrystallization likely occurred at greenschist-facies conditions at ca. 340 Ma.

Structural lineaments of Gaspe from ERTS imagery

NASA Technical Reports Server (NTRS)

Steffensen, R.

1973-01-01

A test study was conducted to assess the value of ERTS images for mapping geologic features of the Gaspe Peninsula, Quebec. The specific objectives of the study were: 1) to ascertain the best procedure to follow in order to obtain valuable geologic data as a result of interpretation; and 2) to indicate in which way these data could relate to mineral exploration. Of the four spectral bands of the Multispectral scanner, the band from 700 to 800 nanometers, which seems to possess the best informational content for geologic study, was selected for analysis. The original ERTS image at a scale of 1:3,700,000 was enlarged about 15 times and reproduced on film. Geologically meaningful lines, called structural lineaments, were outlined and classified according to five categories: morpho-lithologic boundaries, morpho-lithologic lineaments, fault traces, fracture zones and undefined lineaments. Comparison with the geologic map of Gaspe shows that morpho-lithologic boundaries correspond to contacts between regional stratigraphic units. Morpholithologic lineaments follow bedding trends, whereas fracture traces appear as sets of parallel lineaments, intersecting at high angles the previous category of lineaments. Fault traces mark more precisely the location of faults already mapped and spot the presence of presumable faults, not indicated on the geologic map.

Sediment classification using neural networks: An example from the site-U1344A of IODP Expedition 323 in the Bering Sea

NASA Astrophysics Data System (ADS)

Ojha, Maheswar; Maiti, Saumen

2016-03-01

A novel approach based on the concept of Bayesian neural network (BNN) has been implemented for classifying sediment boundaries using downhole log data obtained during Integrated Ocean Drilling Program (IODP) Expedition 323 in the Bering Sea slope region. The Bayesian framework in conjunction with Markov Chain Monte Carlo (MCMC)/hybrid Monte Carlo (HMC) learning paradigm has been applied to constrain the lithology boundaries using density, density porosity, gamma ray, sonic P-wave velocity and electrical resistivity at the Hole U1344A. We have demonstrated the effectiveness of our supervised classification methodology by comparing our findings with a conventional neural network and a Bayesian neural network optimized by scaled conjugate gradient method (SCG), and tested the robustness of the algorithm in the presence of red noise in the data. The Bayesian results based on the HMC algorithm (BNN.HMC) resolve detailed finer structures at certain depths in addition to main lithology such as silty clay, diatom clayey silt and sandy silt. Our method also recovers the lithology information from a depth ranging between 615 and 655 m Wireline log Matched depth below Sea Floor of no core recovery zone. Our analyses demonstrate that the BNN based approach renders robust means for the classification of complex lithology successions at the Hole U1344A, which could be very useful for other studies and understanding the oceanic crustal inhomogeneity and structural discontinuities.

A model of Precambrian geology of Kansas derived from gravity and magnetic data

USGS Publications Warehouse

Xia, J.; Sprowl, D.R.; Steeples, D.W.

1996-01-01

The fabric of the Precambrian geology of Kansas is revealed through inversion of gravity and magnetic data to pseudo-lithology. There are five main steps in the inversion process: (1) reduction of potential-field data to a horizontal plane in the wavenumber domain; (2) separation of the residual anomaly of interest from the regional background, where an assumption is made that the regional anomaly could be represented by some order of polynomial; (3) subtraction of the signal due to the known topography on the Phanerozoic/Precambrian boundary from the residual anomaly (we assume what is left at this stage are the signals due to lateral variation in the Precambrian lithology); (4) inversion of the residual anomaly in the wavenumber domain to density and magnetization distribution in the top part of the Precambrian constrained by the known geologic information; (5) derivation of pseudo-lithology by characterization of density and magnetization. The boundary between the older Central Plains Province to the north and the Southern Granite-Rhyolite Province to the south is clearly delineated. The Midcontinent Rift System appears to widen in central Kansas and involve a considerable portion of southern Kansas. Lithologies in southwestern Kansas appear to change over fairly small areas and include mafic rocks which have not been encountered in drill holes. The texture of the potential field data from southwestern Kansas suggests a history of continental growth by broad extension. Copyright ?? 1996 Elsevier Science Ltd.

Initial Lithologic Mapping Results Using Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) Data

NASA Astrophysics Data System (ADS)

Rowan, L. C.; Mars, J. C.

2001-05-01

Initial analysis of ASTER data of selected areas in the Western United States shows that many important lithologic units can be mapped on the basis of spectral reflectance and spectral emittance. ASTER's most important attributes are 9 bands which record reflected-solar energy with 15 meter- and 30 meter-resolution; 5 bands of emitted energy at 90 meter- resolution; 15 meter-resolution stereoscopic images; and repetitive coverage. Particularly useful 'on-demand' ASTER data products include surface reflectance and surface emissivity images, and digital elevation models (DEM). In the solar-reflected wavelength region (0.4 to 2.5 micrometers), clays, carbonates, hydrous sulphate, and iron-oxide minerals exhibit diagnostic absorption features, whereas the emitted wavelength region (8 to 14 micrometers) provides critical information about anhydrous rock-forming minerals, such as quartz and feldspars, which lack diagnostic absorption features in the solar-reflected region. The Mountain Pass, Calf., Goldfield, Nev., and Virginia Range, Nev. study areas comprise a wide range of lithologic types for evaluating ASTER data. Calibration of the 3 bands recorded in the 0.52 to 0.86 micrometer wavelength region and the 6 bands in the 1.60 to 2.43 micrometer region was improved beyond the 'on-demand' surface reflectance standard product by using in situ spectral reflectance measurements of homogeneous field sites. Validation of this calibration was based on comparisons with spectra from calibrated AVIRIS data, and with additional field measurements. Lithologic mapping based on ASTER bands 1-9 was conducted by using endmember spectra from the image as reference spectra in matched-filter processing. The results were thresholded to display the pixels with the best match for each endmember. The results in these study areas show that Muscovite Group minerals (muscovite, illite, kaolinite) can be mapped over broad reasonably well exposed areas, and that the most intense absorption features occur in hydrothermally altered rocks. In the Mountain Pass area a few exposures containing Fe-muscovite were distinguished from the more extensive Al-mucovite-bearing rocks and soils. Advanced-argillic alteration minerals (alunite, dickite) were detected in the Goldfield mining district and in the Virginia Range. Carbonate Group minerals (calcite, dolomite) were mapped in extensive exposures in the thrust belt of the Mountain Pass area, and well exposed dolomite was distinguished from limestone in several areas. Although skarn deposits consist mainly of calcite and dolomite, their spectral shape in ASTER bands 1-9 is significantly different than typical limestone and dolomite spectra because of the presence of epidote, garnet and chrysotile in the skarn deposits. Mg-OH-bearing minerals (chlorite, biotite, hornblende) proved to be more difficult to map, although generally they were not confused with minerals of the Carbonate Group. Ferric-iron Group minerals were mapped by using a band2/band1 ratio image. Analysis of the surface emissivity standard image products relied on identification of endmember-image spectra by using the pixel-purity index procedure in the ENVI software package, and matched-filter processing. Silica-rich rocks and silica-poor rocks were recognized readily in decorrelation-stretch images, as well as matched-filter endmember images, and 2 intermediate categories were distinguished in most areas.

Application of Remote Sensing in Geological Mapping, Case Study al Maghrabah Area - Hajjah Region, Yemen

NASA Astrophysics Data System (ADS)

Al-Nahmi, F.; Saddiqi, O.; Hilali, A.; Rhinane, H.; Baidder, L.; El arabi, H.; Khanbari, K.

2017-11-01

Remote sensing technology plays an important role today in the geological survey, mapping, analysis and interpretation, which provides a unique opportunity to investigate the geological characteristics of the remote areas of the earth's surface without the need to gain access to an area on the ground. The aim of this study is achievement a geological map of the study area. The data utilizes is Sentinel-2 imagery, the processes used in this study, the OIF Optimum Index Factor is a statistic value that can be used to select the optimum combination of three bands in a satellite image. It's based on the total variance within bands and correlation coefficient between bands, ICA Independent component analysis (3, 4, 6) is a statistical and computational technique for revealing hidden factors that underlie sets of random variables, measurements, or signals, MNF Minimum Noise Fraction (1, 2, 3) is used to determine the inherent dimensionality of image data to segregate noise in the data and to reduce the computational requirements for subsequent processing, Optimum Index Factor is a good method for choosing the best band for lithological mapping. ICA, MNF, also a practical way to extract the structural geology maps. The results in this paper indicate that, the studied area can be divided into four main geological units: Basement rocks (Meta volcanic, Meta sediments), Sedimentary rocks, Intrusive rocks, volcanic rocks. The method used in this study offers great potential for lithological mapping, by using Sentinel-2 imagery, the results were compared with existing geologic maps and were superior and could be used to update the existing maps.

First-order shallow aquifer characteristics across Europe: The International Hydrogeological Map of Europe at scale 1:1.5 Million (IHME1500)

NASA Astrophysics Data System (ADS)

Günther, Andreas; Duscher, Klaus; Broda, Stefan; Clos, Patrick; Reichling, Jörg

2017-04-01

Since the mid of the last century, pan-European hydrogeological overview-mapping is conducted at the scale 1 : 1.5 Million following common standards and guidelines to interpret suitable geologic mapping units in terms of potential uppermost aquifer (or non-aquifer) characteristics. These comprises potential aquifer productivities and general hydrogeological aquifer conditions (fissured vs. porous). The printed IHME1500 dataset successively elaborated and published from 1970 - 2013 consists of 25 individual map sheets. Besides the potential aquifer characterization grouped in six classes, IHME1500 offers a complete coverage of lithological material properties of potential shallow aquifer assemblages, and tracelines of major fault structures. Regional information on groundwater surfaces, aquifer thicknesses and depths, locations and characteristics of groundwater springs and other punctual information related to European groundwater resources is present for some areas in selected map sheets, however not digitally available. Synoptic IHME1500 vector data consists of a topographically corrected, seamless and harmonized polygon layer with attribute information on potential aquifer productivity and lithology. While the standardized aquifer-classification is relatively easy to harmonize across the entire mapped area, the lithological information of IHME1500 is presented using sheet-specific legend information resulting in more than 1000 aquifer lithology classes. An attempt was made to harmonize this information utilizing a specifically developed taxonomic scheme, treating consolidated, partly consolidated and unconsolidated materials separately. The translation of the original lithological information into this scheme allows for a hierarchical grouping of the mapping units into five generalization levels, where the highest aggregation level displays a ternary map showing the distribution of consolidated, partially consolidated and unconsolidated aquifer materials. The harmonized and hierarchically structured IHME1500 information based on the published map sheet data also allows for the extension of the mapped area in regions where only incomplete, unpublished IHME1500 draft information is available. IHME1500 now covers the entire European continent up to the Urals, the Caucasus region, and parts of the Middle East (Turkey, Cyprus, parts of Syria and Iraq). IHME1500 represents the only digitally available coherent overview information on potential groundwater resources and shallow aquifer characteristics across Europe. The data is therefore of great use for European policy support in terms of e.g. transboundary aquifer identification and characterization, the harmonization of regional European groundwater bodies, and the delineation of hot spot regions for aquifer systems under potential environmental stress with respect to climate change, natural hazards or migratory flows. Additionally, the lithological information of IHME1500 represents the only harmonized pan-European dataset on shallow subsurface geologic materials available and can used for the spatial delineation of soil parent materials and as a spatial predictor for the evaluation of geomorphological hazards at overview scales. IHME1500 GIS data can be downloaded through BGŔs product centre (http://produktcenter.bgr.de).

Probability distributions of hydraulic conductivity for the hydrogeologic units of the Death Valley regional ground-water flow system, Nevada and California

USGS Publications Warehouse

Belcher, Wayne R.; Sweetkind, Donald S.; Elliott, Peggy E.

2002-01-01

The use of geologic information such as lithology and rock properties is important to constrain conceptual and numerical hydrogeologic models. This geologic information is difficult to apply explicitly to numerical modeling and analyses because it tends to be qualitative rather than quantitative. This study uses a compilation of hydraulic-conductivity measurements to derive estimates of the probability distributions for several hydrogeologic units within the Death Valley regional ground-water flow system, a geologically and hydrologically complex region underlain by basin-fill sediments, volcanic, intrusive, sedimentary, and metamorphic rocks. Probability distributions of hydraulic conductivity for general rock types have been studied previously; however, this study provides more detailed definition of hydrogeologic units based on lithostratigraphy, lithology, alteration, and fracturing and compares the probability distributions to the aquifer test data. Results suggest that these probability distributions can be used for studies involving, for example, numerical flow modeling, recharge, evapotranspiration, and rainfall runoff. These probability distributions can be used for such studies involving the hydrogeologic units in the region, as well as for similar rock types elsewhere. Within the study area, fracturing appears to have the greatest influence on the hydraulic conductivity of carbonate bedrock hydrogeologic units. Similar to earlier studies, we find that alteration and welding in the Tertiary volcanic rocks greatly influence hydraulic conductivity. As alteration increases, hydraulic conductivity tends to decrease. Increasing degrees of welding appears to increase hydraulic conductivity because welding increases the brittleness of the volcanic rocks, thus increasing the amount of fracturing.

Geologic evolution of the lower Connecticut River valley: Influence of bedrock geology, glacial deposits, and sea level

USGS Publications Warehouse

Stone, Janet R.; Lewis, Ralph S.

2016-01-01

This fieldtrip illustrates the character of the lower Connecticut River bedrock valley, in particular its depth, and the lithology and structure of bedrock units it crosses. It examines the character and distribution of the glaciodeltaic terraces that partially fill the valley and discusses the depth of postglacial incision into them.

Developing a thermal characteristic index for lithology identification using thermal infrared remote sensing data

NASA Astrophysics Data System (ADS)

Wei, Jiali; Liu, Xiangnan; Ding, Chao; Liu, Meiling; Jin, Ming; Li, Dongdong

2017-01-01

In remote sensing petrology fields, studies have mainly concentrated on spectroscopy remote sensing research, and methods to identify minerals and rocks are mainly based on the analysis and enhancement of spectral features. Few studies have reported the application of thermodynamics for lithology identification. This paper aims to establish a thermal characteristic index (TCI) to explore rock thermal behavior responding to defined environmental systems. The study area is located in the northern Qinghai Province, China, on the northern edge of the Qinghai-Tibet Plateau, where mafic-ultramafic rock, quartz-rich rock, alkali granite rock and carbonate rock are well exposed; the pixel samples of these rocks and vegetation were obtained based on relevant indices and geological maps. The scatter plots of TCI indicate that mafic-ultramafic rock and quartz-rich rock can be well extracted from other surface objects when interference from vegetation is lower. On account of the complexity of environmental systems, three periods of TCI were used to construct a three-dimensional scatter plot, named the multi-temporal thermal feature space (MTTFS) model. Then, the Bayes discriminant analysis algorithm was applied to the MTTFS model to extract rocks quantitatively. The classification accuracy of mafic-ultramafic rock is more than 75% in both training data and test data, which suggests TCI can act as a sensitive indicator to distinguish rocks and the MTTFS model can accurately extract mafic-ultramafic rock from other surface objects. We deduce that the use of thermodynamics is promising in lithology identification when an effective index is constructed and an appropriated model is selected.

Hydrologic, lithologic, and chemical data for sediment in the shallow alluvial aquifer at two sites near Fallon, Churchill County, Nevada, 1984-85

USGS Publications Warehouse

Lico, M.S.; Welch, A.H.; Hughes, J.L.

1986-01-01

The U.S. Geological Survey collected an extensive amount of hydrogeologic data from the shallow alluvial aquifer at two study sites near Fallon, Nevada, from 1984 though 1985. These data were collected as part of a study to determine the geochemical controls on the mobility of arsenic and other trace elements in shallow groundwater systems. The main study area is approximately 7 miles south of Fallon. A subsidiary study area is about 8 miles east of Fallon. The data collected include lithologic logs and water level altitudes for the augered sampling wells and piezometers, and determinations of arsenic and selenium content, grain size, porosity, hydraulic conductivity, and mineralogy for sediment samples from cores. (USGS)

Subdivision of the Cambrian-Ordovician Upper Sandstone Aquifer'' in the Fox Cities area, east-central Wisconsin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Erikson, K.A.; Smith, G.L.

The informally-named Upper Sandstone Aquifer,'' a lithologically heterogeneous unit, has been subdivided into three thinner hydrostratigraphic units, the Upper Cambrian Jordan Formation (sandstone), the Lower Ordovician Prairie du Chien Group (dolomite), and the Middle Ordovician St. Peter Formation (mostly sandstone). Reevaluation of the Upper Sandstone Aquifer'' in the Fox Cities area (Appleton, Neenah, Menasha) was based on detailed analysis of 125 geologic well logs and 200 well-construction reports. Isopach maps and geologic cross-sections of these units in the Fox Cities area show extreme variations in thickness over short lateral distances. Although the Jordan Formation has a uniform thickness of 13more » m (40 ft), the Prairie du Chien Group varies from 0--88 m (0--275 ft). The St. Peter Formation varies in thickness from 0--108 m (0--335 ft). The Prairie du Chien Group is relatively thin or absent in the Fox Cities area in locations where the overlying St. Peter Formation is relatively thick. St Peter can be further subdivided into Readstown, Tonti, and Glenwood Members. The Readstown Member is a lithologically heterogeneous unit of variable thickness and distribution. The Tonti Member is a poorly cemented, fine-medium quartz arenite with which is lumped the Glenwood Member, a conglomeratic, silty medium-coarse sandstone. Maximum St. Peter thicknesses represent filled paleokarst depressions developed on top of the Prairie du Chien Group, with profound implications for estimates of hydraulic conductivity.« less

Using Outcrop Exposures on the Road to Yellowknife Bay to Build a Stratigraphic Column, Gale Crater, Mars

NASA Technical Reports Server (NTRS)

Stack, K. M.; Grotzinger, J. P.; Sumner, D.; Ehlmann, B. L.; Milliken, R. E.; Eigenbrode, J. L.; Gupta, S.; Williams, R. M. E.; Kah, L. C.; Lewis, K. W.

2013-01-01

Since landing in Gale Crater on August 5, 2012, the Curiosity rover has driven 450 m east, descending approximately 15 m in elevation from the Bradbury landing site to Yellowknife Bay. Outcrop exposure along this drive has been discontinuous, but isolated outcrops may represent windows into underlying inplace stratigraphy. This study presents an inventory of outcrops targeted by Curiosity (Figs. 1-2), grouped by lithological properties observed in Mastcam and Navcam imagery. Outcrop locations are placed in a stratigraphic context using orbital imagery and first principles of stratigraphy. The stratigraphic models presented here represent an essential first step in understanding the relative age relationships of lithological units encountered at the Curiosity landing site. Such observations will provide crucial context for assessing habitability potential of ancient Gale crater environments and organic matter preservation.

The depositional setting of the Late Quaternary sedimentary fill in southern Bannu basin, Northwest Himalayan fold and thrust belt, Pakistan.

PubMed

Farid, Asam; Khalid, Perveiz; Jadoon, Khan Zaib; Jouini, Mohammed Soufiane

2014-10-01

Geostatistical variogram and inversion techniques combined with modern visualization tools have made it possible to re-model one-dimensional electrical resistivity data into two-dimensional (2D) models of the near subsurface. The resultant models are capable of extending the original interpretation of the data to depict alluvium layers as individual lithological units within the 2D space. By tuning the variogram parameters used in this approach, it is then possible to visualize individual lithofacies and geomorphological features for these lithologic units. The study re-examines an electrical resistivity dataset collected as part of a groundwater study in an area of the Bannu basin in Pakistan. Additional lithological logs from boreholes throughout the area have been combined with the existing resistivity data for calibration. Tectonic activity during the Himalayan orogeny uplifted and generated significant faulting in the rocks resulting in the formation of a depression which subsequently has been filled with clay-silt and dirty sand facies typical of lacustrine and flood plain environments. Streams arising from adjacent mountains have reworked these facies which have been eroded and replaced by gravel-sand facies along channels. It is concluded that the sediments have been deposited as prograding fan shaped bodies, flood plain, and lacustrine deposits. Clay-silt facies mark the locations of paleo depressions or lake environments, which have changed position over time due to local tectonic activity and sedimentation. The Lakki plain alluvial system has thus formed as a result of local tectonic activity with fluvial erosion and deposition characterized by coarse sediments with high electrical resistivities near the mountain ranges and fine sediments with medium to low electrical resistivities towards the basin center.

Granulite-facies rocks in the Whatley Mill gneiss, Pine Mountain basement massif, Eastern Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniell, N.; Salpas, P.A.

1993-03-01

The Pine Mountain basement massif is a granulite terrane exposed in a tectonic window through the Inner Piedmont of western Georgia and eastern Alabama. Investigations of the westernmost extent of the massif, the Whatley Mill Gneiss, have revealed four distinct lithologies: (1) an augen gneiss, the type lithology; (2) mylonite that develops in the shear zones cutting the unit; (3) a phaneritic rock showing weak to no foliation; (4) enclaves of biotite gneiss within the weakly-foliated rock. Additionally, the weakly-foliated rock comprises two distinct phases which are in sharp contact along curved and undulating boundaries: phase 1 is a coarser-grainedmore » rock; phase 2 is a finer-grained rock of the same mineralogy as phase 1 except it contains rare hypersthene. This first recorded observation of hypersthene unequivocally confirms the granulite-facies origin of the unit. Major and trace element compositions of the phase 1 rock are identical to those of the augen gneiss. The phase 2 rock, has a distinct composition with higher SiO[sub 2] and lower incompatible trace elements than the phase 1 rock. The enclaves display a range in major elements but higher incompatible elements than the other lithologies. Geochemical and petrologic relationships leads one to interpret: (1) the weakly-foliated rock retains many of its primary igneous features including its two phases and enclaves; (2) the two phases of the weakly-foliated rock arose as a result of injection of one magma (phase 2) into a cooler, crystal mush solidifying from another magma (phase 1); (3) the enclaves represent either autoliths of xenoliths; (4) the augen gneiss arose by isochemical deformation of the phase 1 rock.« less

Utilizing borehole electrical images to interpret lithofacies of fan-delta: A case study of Lower Triassic Baikouquan Formation in Mahu Depression, Junggar Basin, China

NASA Astrophysics Data System (ADS)

Yuan, Rui; Zhang, Changmin; Tang, Yong; Qu, Jianhua; Guo, Xudong; Sun, Yuqiu; Zhu, Rui; Zhou, Yuanquan (Nancy)

2017-11-01

Large-scale conglomerate fan-delta aprons were typical deposits on the slope of Mahu Depression during the Early Triassic. Without outcrops, it is difficult to study the lithofacies only by examining the limited cores from the main oil-bearing interval of the Baikouquan Formation. Borehole electrical imaging log provides abundant high-resolution geologic information that is obtainable only from real rocks previously. Referring to the lithology and sedimentary structure of cores, a case study of fan-deltas in the Lower Triassic Baikouquan Formation of the Mahu Depression presents a methodology for interpreting the complicated lithofacies utilizing borehole electrical images. Eleven types of lithologies and five types of sedimentary structures are summarized in borehole electrical images. The sediments are fining upward from gravel to silt and clay in the Baikouquan Formation. Fine-pebbles and granules are the main deposits in T1b1 and T1b2, but sandstones, siltstones and mudstones are more developed in T1b3. The main sedimentary textures are massive beddings, cross beddings and scour-and-fill structures. Parallel and horizontal beddings are more developed in T1b3 relatively. On integrated analysis of the lithology and sedimentary structure, eight lithofacies from electrical images, referred to as image lithofacies, is established for the fan-deltas. Granules to coarse-pebbles within massive beddings, granules to coarse-pebbles within cross and parallel beddings, siltstones within horizontal and massive beddings are the most developed lithofacies respectively in T1b1, T1b2 and T1b3. It indicates a gradual rise of the lake level of Mahu depression during the Early Triassic, with the fan-delta aprons retrograding towards to the margin of the basin. Therefore, the borehole electrical imaging log compensate for the limitation of cores of the Baikouquan Formation, providing an effective new approach to interpret the lithofacies of fan-delta.

Fault-zone structure and weakening processes in basin-scale reverse faults: The Moonlight Fault Zone, South Island, New Zealand

NASA Astrophysics Data System (ADS)

Alder, S.; Smith, S. A. F.; Scott, J. M.

2016-10-01

The >200 km long Moonlight Fault Zone (MFZ) in southern New Zealand was an Oligocene basin-bounding normal fault zone that reactivated in the Miocene as a high-angle reverse fault (present dip angle 65°-75°). Regional exhumation in the last c. 5 Ma has resulted in deep exposures of the MFZ that present an opportunity to study the structure and deformation processes that were active in a basin-scale reverse fault at basement depths. Syn-rift sediments are preserved only as thin fault-bound slivers. The hanging wall and footwall of the MFZ are mainly greenschist facies quartzofeldspathic schists that have a steeply-dipping (55°-75°) foliation subparallel to the main fault trace. In more fissile lithologies (e.g. greyschists), hanging-wall deformation occurred by the development of foliation-parallel breccia layers up to a few centimetres thick. Greyschists in the footwall deformed mainly by folding and formation of tabular, foliation-parallel breccias up to 1 m wide. Where the hanging-wall contains more competent lithologies (e.g. greenschist facies metabasite) it is laced with networks of pseudotachylyte that formed parallel to the host rock foliation in a damage zone extending up to 500 m from the main fault trace. The fault core contains an up to 20 m thick sequence of breccias, cataclasites and foliated cataclasites preserving evidence for the progressive development of interconnected networks of (partly authigenic) chlorite and muscovite. Deformation in the fault core occurred by cataclasis of quartz and albite, frictional sliding of chlorite and muscovite grains, and dissolution-precipitation. Combined with published friction and permeability data, our observations suggest that: 1) host rock lithology and anisotropy were the primary controls on the structure of the MFZ at basement depths and 2) high-angle reverse slip was facilitated by the low frictional strength of fault core materials. Restriction of pseudotachylyte networks to the hanging-wall of the MFZ further suggests that the wide, phyllosilicate-rich fault core acted as an efficient hydrological barrier, resulting in a relatively hydrous footwall and fault core but a relatively dry hanging-wall.

Idea of Identification of Copper Ore with the Use of Process Analyser Technology Sensors

NASA Astrophysics Data System (ADS)

Jurdziak, Leszek; Kaszuba, Damian; Kawalec, Witold; Król, Robert

2016-10-01

The Polish resources of the copper ore exploited by the KGHM S.A. underground mines are considered as one of the most complex in the world and - consequently - the most difficult to be processed. The ore consists of three lithology forms: dolomites, shales and sandstones but in different proportions which has a significant impact on the effectiveness of the grinding and flotation processes. The lithological composition of the ore is generally recognised in-situ but after being mined it is blended on its long way from various mining fields to the processing plant by the complex transportation system consisting of belt conveyors with numerous switching points, ore bunkers and shafts. Identification of the lithological composition of the ore being supplied to the processing plant should improve the adjustments of the ore processing machinery equipment aiming to decrease the specific processing (mainly grinding) energy consumption as well as increase the metal recovery. The novel idea of Process Analyser Technology (PAT) sensors - information carrying pellets, dropped into the transported or processed bulk material which can be read directly when needed - is investigated for various applications within the DISIRE project (a part of the SPIRE initiative, acting under the Horizon2020 framework program) and here is adopted for implementing the annotation the transported copper ore for the needs of ore processing plants control. The identification of the lithological composition of ore blended on its way to the processing plant can be achieved by an information system consisting of pellets that keep the information about the original location of the portions of conveyed ore, the digital, geological database keeping the data of in-situ lithology and the simulation models of the transportation system, necessary to evaluate the composition of the blended ore. The assumptions of the proposed solution and the plan of necessary in-situ tests (with the special respect to harsh environment of

Palaeogeographic, palaeoclimatic, palaeohydrological and chemical/biochemical controls on accumulation of late Eocene coastal lacustrine-palustrine limestones, Southern England

NASA Astrophysics Data System (ADS)

Armenteros, Ildefonso; Edwards, Nicholas

2012-12-01

The shallow-lacustrine to palustrine Hatherwood Limestone Member of the late Eocene Headon Hill Formation, Southern England, is in a succession of fluvio-estuarine and laguno-lacustrine siliciclastic sediments. It is up to 8.0 m thick and is subdivided by metric-scale palaeotopographic erosion surfaces, one of which underlies lenticular humic siliciclastic mudstones. The limestone lithologies are (1) biocalcilutites/biocalcisiltites, (2) biocalcarenites, (3) calcirudites, and (4) laterally-discontinuous laminar and fenestral crusts. Lithology (1) accumulated in a low-energy shallow-lacustrine depositional environment, indicated by the predominance of pulmonate pond-snails in the mollusc assemblage. In contrast, lithologies (2) and (3) are the coarse-grained fills of shallow palaeotopographic lows, and also form basal lags and palaeokarst-fills. Lithology (3) comprises remnant autochthonous lags that resulted from selective erosion during lacustrine transgressions. Brecciation and proto-intraclast to nodular differentiation in lithology (2) suggests derivation of the intraclasts from subaerially- and pedogenically-modified shallow-lacustrine muds. Laminar crusts (4), 0.5-6.0 cm in thickness, display irregularly undulose and anastamosing laminations 150-400 μm thick, that display differential staining by iron oxide. The abundance of rootlet traces and calcitised parenchymatic root tissues in the fenestral crusts suggests a palustrine depositional environment for these lithologies. The siliciclastic mudstone lithologies are (1) black humic muds and (2) blue-green silty muds and marls. The high C/N molar ratio of the black muds suggests derivation of the humic content mainly from vascular plants in local wetlands. The mollusc assemblage of the blue-green siliciclastic muds resembles floodplain lake assemblages from the regional Palaeogene succession. Mean stable isotopic values for limestone samples, of - 4.75 ± 1.53 for δ13C and - 2.77 ± 1.47 for δ18O, indicate a relatively heavy tendency within published spectra for Tertiary lacustrine carbonates. The δ18O isotope results agree with published subtropical surface-water palaeotemperatures for this succession. The total characteristics of the Member therefore suggest a shallow-lacustrine to palustrine depositional environment. Pedogenic overprinting and mechanical reworking displayed by the limestones are attributable to seasonal fluctuations of water level during lake highstands, but in this marine-influenced setting, major long-term lake lowstands, resulting in deep erosion and palaeokarsting of the limestones, may be attributable to falls in relative sea-level. The biocalcilutites and humic muds accumulated during the ensuing lake transgressions.

Transformation of Serpentinite to Listvenite as Recorded in the Vein History of Rocks From Oman Drilling Project Hole BT1B

NASA Astrophysics Data System (ADS)

Manning, C. E.; Kelemen, P. B.; Michibayashi, K.; Harris, M.; Urai, J. L.; de Obeso, J. C.; Jesus, A. P. M.; Zeko, D.

2017-12-01

Oman Drilling Project Hole BT1B intersected 191 m of listvenite (magnesite + quartz rock) and serpentinite in the hanging wall of the basal thrust of the Oman ophiolite. Recovery was 100%. Listvenite is the dominant lithology in the upper plate rocks (166 m). Its shows wide color and textural variation, including pseudomorphic replacement of serpentinized peridotite. Serpentinite was encountered in two main contiguous intervals totaling 25 m. In light of the strongly metasomatic nature for the origin of listvenite, a substantial portion of the core description effort was dedicated to characterization of the complex veining history recorded in the hole. Dense veining is recorded in both lithologies. The density of <1 mm veins is >200/m. The density of veins >1 mm was 50-100/m, with somewhat higher densities recorded in serpentinite than in listvenite. In order of oldest to youngest, the main vein types in serpentinite are microscopic mesh-textured serpentine veins, macroscopic serpentine veins, carbonate-oxide veins, and carbonate veins. The vein paragenesis in listvenite is: early carbonate-oxide veins, followed by carbonate and carbonate-quartz veins, then late carbonate veins. The carbonate-oxide and carbonate veins are shared by the lithologies and hold clues to the transformation of ultramafic rocks to listvenite. Carbonate-oxide veins form a distinctive set that is interpreted to be the earliest record of carbonate formation in serpentinite. They contain Fe-oxide, usually hematite, on a medial line, with antitaxial magnesite crystals growing outward and showing terminations against wall rock minerals. Antitaxial textures may be evidence of positive reaction volumes. In serpentinite, secondary serpentine after earlier serpentine is common at vein margins. Carbonate-oxide veins are the earliest observed in listvenite, where they may form isolated veins to dense, aligned networks that impart a foliated texture. In some cases, they appear to predate replacement of serpentine by microcrystalline quartz. Both lithologies record later, coarser, through going carbonate ± quartz veins. Preliminary vein petrology in BT1B rocks indicates that fracture formation and filling by secondary minerals is integral to the metasomatic replacement of altered peridotite by listvenite.

Magmatic activity at Islas Marias Archipelago, Gulf of California: Oceanic lithosphere with gabbroic sills versus Jurassic-Cretaceous arc components.

NASA Astrophysics Data System (ADS)

Schaaf, P. E. G.; Solis-Pichardo, G.; Hernandez-Trevino, T.; Villanueva, D.; Arrieta, G. F.; Rochin, H.; Rodriguez, L. F.; Bohnel, H.; Weber, B.

2015-12-01

Islas Marias Archipelago consists of four islands located in the mouth of the Gulf of California. Lithologically three of them (Maria Madre, San Juanito, and Maria Cleofas) are quite similar with a 165-170 Ma metamorphic basement, 75-85 Ma intrusive and extrusive rocks, and a sedimentary sandstone cover, which according to its foraminiferous content recorded multiple uplift and subsidence events related to the opening of the Gulf. However, these units are absent on Maria Magdalena island which is positioned between the other islands. Here, instead, oceanic lithosphere with pillow lavas and gabbroic sills, intercalated with sandstones form the dominant outcrops. Their geochemical and isotopic characteristics are similar to N-MORB with epsilon Nd values around +10 and 87Sr/86Sr of 0.70290. The gabbros are not older than 22 Ma. Magdalena island was obviously uplifted separately from the other islands of the archipelago, probably along a now hidden transform fault system along the East Pacific Rise. Metamorphic and igneous rocks of the other islands can be correlated to lithologically similar units in the Los Cabos Block, Baja California, or to the continental margin units in Sinaloa, Nayarit and Jalisco states when looking at their geochemical and geochronological signatures. Paleomagnetic studies on 35 sampling sites from all 4 islands give evidence for relatively small scale tectonic movements.

Quaternary Geologic Map of the Regina 4 Degrees x 6 Degrees Quadrangle, United States and Canada

USGS Publications Warehouse

Fullerton, David S.; Christiansen, Earl A.; Schreiner, Bryan T.; Colton, Roger B.; Clayton, Lee; Bush, Charles A.; Fullerton, David S.

2007-01-01

For scientific purposes, the map differentiates Quaternary surficial deposits and materials on the basis of clast lithology or composition, matrix texture or particle size, structure, genesis, stratigraphic relations, engineering geologic properties, and relative age, as shown on the correlation diagram and indicated in the 'Description of Map Units'. Deposits of some constructional landforms, such as end moraines, are distinguished as map units. Deposits of erosional landforms, such as outwash terraces, are not distinguished, although glaciofluvial, ice-contact, fluvial, and lacustrine deposits that are mapped may be terraced. Differentiation of sequences of fluvial and glaciofluvial deposits at this scale is not possible. For practical purposes, the map is a surficial materials map. Materials are distinguished on the basis of lithology or composition, texture or particle size, and other physical, chemical, and engineering characteristics. It is not a map of soils that are recognized and classified in pedology or agronomy. Rather, it is a generalized map of soils as recognized in engineering geology, or of substrata or parent materials in which pedologic or agronomic soils are formed. As a materials map, it serves as a base from which a variety of maps for use in planning engineering, land-use planning, or land-management projects can be derived and from which a variety of maps relating to earth surface processes and Quaternary geologic history can be derived.

Urban land-use study plan for the National Water-Quality Assessment Program

USGS Publications Warehouse

Squillace, P.J.; Price, C.V.

1996-01-01

This study plan is for Urban Land-Use Studies initiated as part of the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) Program. There are two Urban Land-Use Study objectives: (1) Define the water quality in recharge areas of shallow aquifers underlying areas of new residential and commercial land use in large metropolitan areas, and (2) determine which natural and human factors most strongly affect the occurrence of contaminants in these shallow aquifers. To meet objective 1, each NAWQA Study Unit will install and collect water samples from at least 30 randomly located monitoring wells in a metropolitan area. To meet objective 2, aquifer characteristics and land-use information will be documented. This includes particle-size analysis of each major lithologic unit both in the unsaturated zone and in the aquifer near the water table. The percentage of organic carbon also will be determined for each lithologic unit. Geographic information system coverages will be created that document existing land use around the wells. These data will aid NAWQA personnel in relating natural and human factors to the occurrence of contaminants. Water samples for age dating also will be collected from all monitoring wells, but the samples will be stored until the occurrence of contaminants has been determined. Age-date analysis will be done only on those samples that have no detectable concentrations of anthropogenic contaminants.

Geologic Map and Cross Sections of the McGinness Hills Geothermal Area - GIS Data

DOE Data Explorer

Faulds, James E.

2013-12-31

Geologic map data in shapefile format that includes faults, unit contacts, unit polygons, attitudes of strata and faults, and surficial geothermal features. 5 cross‐sections in Adobe Illustrator format. Comprehensive catalogue of drill‐hole data in spreadsheet, shapefile, and Geosoft database formats. Includes XYZ locations of well heads, year drilled, type of well, operator, total depths, well path data (deviations), lithology logs, and temperature data. 3D model constructed with EarthVision using geologic map data, cross‐sections, drill‐hole data, and geophysics.

Relations between extensional tectonics and magmatism within the Southern Oklahoma aulacogen

NASA Technical Reports Server (NTRS)

Mcconnell, D. A.; Gilbert, M. C.

1985-01-01

Variations in the geometry, distribution and thickness of Cambrian igneous and sedimentary units within southwest Oklahoma are related to a late Proterozoic - early Paleozoic rifting event which formed the Southern Oklahoma aulacogen. These rock units are exposed in the Wichita Mountains, southwest Olkahoma, located on the northern margin of a Proterozoic basin, identified in the subsurface by COCORP reflection data. Overprinting of the Cambrian extensional event by Pennyslvanian tectonism obsured the influence of pre-existing basement structures and contrasting basement lithologies upon the initial development of the aulacogen.

Mapping groundwater reserves in northwestern Cambodia with the combined use of data from lithologs and time-domain-electromagnetic and magnetic-resonance soundings

NASA Astrophysics Data System (ADS)

Valois, Remi; Vouillamoz, Jean-Michel; Lun, Sambo; Arnout, Ludovic

2018-06-01

Lack of access to water is the primary constraint to development in rural areas of northwestern Cambodia. Communities lack water for both domestic and irrigation purposes. To provide access to drinking water, governmental and aid agencies have focused on drilling shallow boreholes but they have not had a clear understanding of groundwater potential. The goal of this study has been to improve hydrogeological knowledge of two districts in Oddar Meanchey Province by analyzing borehole lithologs and geophysical data sets. The comparison of 55 time-domain electromagnetic (TEM) soundings and lithologs, as well as 66 magnetic-resonance soundings (MRS) with TEM soundings, allows a better understanding of the links between geology, electrical resistivity and hydrogeological parameters such as the specific yield ( S y) derived from MRS. The main findings are that water inflow and S y are more related to electrical resistivity and elevation than to the litholog description. Indeed, conductive media are associated with a null value of S y, whereas resistive rocks at low elevation are always linked to strictly positive S y. A new methodology was developed to create maps of groundwater reserves based on 612 TEM soundings and the observed relationship between resistivity and S y. TEM soundings were inverted using a quasi-3D modeling approach called `spatially constrained inversion'. Such maps will, no doubt, be very useful for borehole siting and in the economic development of the province because they clearly distinguish areas of high groundwater-reserves potential from areas that lack reserves.

Substrate controls on the longitudinal profile of bedrock channels: Implications for reach-scale roughness

Treesearch

Jaime R. Goode; Ellen Wohl

2010-01-01

In this paper we examine the relationships among bedrock properties and hydraulics in shaping bedrock channel morphology at the reach scale. The Ocoee River and four other bedrock streams in the Blue Ridge province of the southeastern United States, which have reach scale differences in bedrock erodibility controlled by lithologic and structural variation, are the...

Late Quaternary environmental changes inferred from n-alkane evidence in coastal area of southern Hainan Island, China

NASA Astrophysics Data System (ADS)

Wang, Mengyuan; Zheng, Zhuo

2016-04-01

The studied core was a coastal core in Hainan Island, China. It is in length of 49.01m and divided into four Units (MIS 1~MIS 6) according to lithology description. The Optically Stimulated Luminescence (OSL) attributes the sediments from Unit 3 to the Oxygen Isotope Stage of MIS 5e (Unit 3b and 3c) and 5d (Unit 3a). To interpret the origination of organic carbons and to reconstruct paleovegetation changes, n-alkane, δ13C and TOC have been used in the present research. The result of n-alkanes distribution indicates a series of changes of sedimentary environment and terrestrial input. The shallow water facies at Unit 2, 3a and 4 is mainly characterized by short carbon chain n-alkanes and relatively low concentration. Contrasting with that of deep-water marine facies of MIS 5e (Unit 3b), the n-alkane pattern is typical bimodal and the main peaks are both in short and long carbon chains. During Unit 3b-1 (MIS 5e), more terrestrial original n-alkanes contribute to the concentration of TOC than oceanic. Organic matter source is mainly terrestrial origination. Total organic matter input mechanism of TLG-01 correlates with sediment grain size (average grain size). Total organic carbon input is enhanced with the increasing of fine grain size component. The variation of CPI (25-33) value in this study correlates with hydrological energy. The highest CPI (25-33) value is shown in the high sea level period of MIS 5e, comparing with that in MIS 5d and MIS 1. High CPI value corresponds to high TOC and average grain size (Φ) value. In the weak hydrological energy sedimentary environment, more terrestrial organic matter, together with TOC, deposit in the study area. ACL (25-33) index display higher values in the interglacial period (MIS 5 and MIS 1) than MIS 3 (sediments weathered during MIS 2) and MIS 6. Paq proxy, together with δ13C, estimates the mangrove growing depth in MIS 5e. The correlation between δ13C and each carbon chain alkane state stabilize and turbulence of sedimentary environment in MIS 5e. Sediments deposit in stable weak hydrological energy environment show order and grouped alkanes distribution (Unit 3b-2). High and positive correlation coefficients of δ13C and each carbon chain alkane show the dominant alkanes contributed to organic carbon (δ13C).

Evaluation of criteria for selecting the spectral attributes of digital LANDSAT MSS imagery for discriminating lithological units in the lower Curaca River Valley, Bahia. [Brazil

NASA Technical Reports Server (NTRS)

Paradella, W. R. (Principal Investigator)

1984-01-01

The use of spectral attributes criteria was investigated, based on measures of statistical distance of separability between thematic classes in MSS digital LANDSAT imagery, in order to select the best subsets of channels in composite colors for the detection and discrimination of lithological units in the lower valley of Curaca River, State of Bahia, Brazil. Three situations were investigated: (1) selection of the three best channels, considering all of the original bands (channels 4, 5, 6, and 7); (2) selection of the three best bands, considering the six MSS band-ratios (channels 4/5, 4/6. 4/7, 5/6, 5/7, and 6/7); and (3) selection of the three best bands in a hybrid approach (the four original bands and the six ratios). A visual analysis was done on color composite images using the selected sets. Results show that the hybrid product (bands 4, 5/7, and 7 with green, blue, and red respectively) and the Normal Color Composite (bands 4, 5, and 7 with blue, green, and red colors respectively) had the best performance.

Nature and origin of mineral coatings on volcanic rocks of the Black Mountain, Stonewall Mountain, and Kane Springs, Wash volcanic centers, Southern Nevada

NASA Technical Reports Server (NTRS)

Taranik, James V.; Noble, Donald C.; Hsu, Liang C.; Spatz, David M.

1987-01-01

LANDSAT Thematic Mapper imagery was evaluated over 3 Tertiary calderas in southern Nevada. Each volcanic center derived from a highly evolved silici magmatic system represented today by well exposed diverse lithologies. Distinctive imagery contrast between some of the late ash flows and earlier units follows from the high relative reflectance in longer wavelength bands (bands 5 and 7) of the former. Enhancement techniques provide color composite images which highlight some of the units in remarkable color contrast. Inasmuch as coatings on the tuffs are incompletely developed and apparently largely dependent spectrally on rock properties independent of petrochemistry, it is felt that the distinctive imagery characteristics are more a function of primary lithologic or petrochemical properties. Any given outcrop is backdrop for a variety of cover types, of which coatings, at various stages of maturity, are one. Petrographic and X-ray diffraction analysis of the outer air-interface zone of coatings reveal they are composed chiefly of amorphous compounds, probably with varying proportions of iron and manganese. Observations support an origin for some outer (air-interface) coating constituents exogenous to the underlying host.

Geologic controls on gas hydrate occurrence in the Mount Elbert prospect, Alaska North Slope

USGS Publications Warehouse

Boswell, R.; Rose, K.; Collett, T.S.; Lee, M.; Winters, W.; Lewis, K.A.; Agena, W.

2011-01-01

Data acquired at the BPXA-DOE-USGS Mount Elbert Gas Hydrate Stratigraphic Test Well, drilled in the Milne Point area of the Alaska North Slope in February, 2007, indicates two zones of high gas hydrate saturation within the Eocene Sagavanirktok Formation. Gas hydrate is observed in two separate sand reservoirs (the D and C units), in the stratigraphically highest portions of those sands, and is not detected in non-sand lithologies. In the younger D unit, gas hydrate appears to fill much of the available reservoir space at the top of the unit. The degree of vertical fill with the D unit is closely related to the unit reservoir quality. A thick, low-permeability clay-dominated unit serves as an upper seal, whereas a subtle transition to more clay-rich, and interbedded sand, silt, and clay units is associated with the base of gas hydrate occurrence. In the underlying C unit, the reservoir is similarly capped by a clay-dominated section, with gas hydrate filling the relatively lower-quality sands at the top of the unit leaving an underlying thick section of high-reservoir quality sands devoid of gas hydrate. Evaluation of well log, core, and seismic data indicate that the gas hydrate occurs within complex combination stratigraphic/structural traps. Structural trapping is provided by a four-way fold closure augmented by a large western bounding fault. Lithologic variation is also a likely strong control on lateral extent of the reservoirs, particularly in the D unit accumulation, where gas hydrate appears to extend beyond the limits of the structural closure. Porous and permeable zones within the C unit sand are only partially charged due most likely to limited structural trapping in the reservoir lithofacies during the period of primary charging. The occurrence of the gas hydrate within the sands in the upper portions of both the C and D units and along the crest of the fold is consistent with an interpretation that these deposits are converted free gas accumulations formed prior to the imposition of gas hydrate stability conditions. ?? 2009.

A lithology identification method for continental shale oil reservoir based on BP neural network

NASA Astrophysics Data System (ADS)

Han, Luo; Fuqiang, Lai; Zheng, Dong; Weixu, Xia

2018-06-01

The Dongying Depression and Jiyang Depression of the Bohai Bay Basin consist of continental sedimentary facies with a variable sedimentary environment and the shale layer system has a variety of lithologies and strong heterogeneity. It is difficult to accurately identify the lithologies with traditional lithology identification methods. The back propagation (BP) neural network was used to predict the lithology of continental shale oil reservoirs. Based on the rock slice identification, x-ray diffraction bulk rock mineral analysis, scanning electron microscope analysis, and the data of well logging and logging, the lithology was divided with carbonate, clay and felsic as end-member minerals. According to the core-electrical relationship, the frequency histogram was then used to calculate the logging response range of each lithology. The lithology-sensitive curves selected from 23 logging curves (GR, AC, CNL, DEN, etc) were chosen as the input variables. Finally, the BP neural network training model was established to predict the lithology. The lithology in the study area can be divided into four types: mudstone, lime mudstone, lime oil-mudstone, and lime argillaceous oil-shale. The logging responses of lithology were complicated and characterized by the low values of four indicators and medium values of two indicators. By comparing the number of hidden nodes and the number of training times, we found that the number of 15 hidden nodes and 1000 times of training yielded the best training results. The optimal neural network training model was established based on the above results. The lithology prediction results of BP neural network of well XX-1 showed that the accuracy rate was over 80%, indicating that the method was suitable for lithology identification of continental shale stratigraphy. The study provided the basis for the reservoir quality and oily evaluation of continental shale reservoirs and was of great significance to shale oil and gas exploration.

L'aquifère du bassin de la Mamora, Maroc: geometrie et ecoulements souterrainsThe aquifer of the Mamora Basin, Morocco: geometry and groundwater flow

NASA Astrophysics Data System (ADS)

Zouhri, L.

2001-05-01

The Mamora aquifer, in the northern Moroccan Meseta, constitutes the main regional water resource. Its impermeable basement is mostly composed of blue marls. The lithostratigraphy of the basin aquifer is characterised by a sequence of sandstones, sandy limestones, conglomerates and sandy clays. The structure of the basement of the Mamora aquifer, deduced from electrical resistivity measurements, allowed the hydrogeological behaviour of the reservoir, and the direction of the groundwater flow, to be established. The combination of the lithological, morphological, piezometric, geophysical and structural investigations revealed a northward thickening of the substrate with groundwater flow towards the Rharb (to the north) and towards the Atlantic Ocean (northwest). This 'multicriteria' approach enabled a structural model to be defined, which correlated well with the aquifer geometry and the groundwater flow. The variability of the hydrogeological units, and the northward thickening of the sedimentary facies, were controlled by northeast-southwest orientated faults, which affect their impermeability.

Estimation of Lithological Classification in Taipei Basin: A Bayesian Maximum Entropy Method

NASA Astrophysics Data System (ADS)

Wu, Meng-Ting; Lin, Yuan-Chien; Yu, Hwa-Lung

2015-04-01

In environmental or other scientific applications, we must have a certain understanding of geological lithological composition. Because of restrictions of real conditions, only limited amount of data can be acquired. To find out the lithological distribution in the study area, many spatial statistical methods used to estimate the lithological composition on unsampled points or grids. This study applied the Bayesian Maximum Entropy (BME method), which is an emerging method of the geological spatiotemporal statistics field. The BME method can identify the spatiotemporal correlation of the data, and combine not only the hard data but the soft data to improve estimation. The data of lithological classification is discrete categorical data. Therefore, this research applied Categorical BME to establish a complete three-dimensional Lithological estimation model. Apply the limited hard data from the cores and the soft data generated from the geological dating data and the virtual wells to estimate the three-dimensional lithological classification in Taipei Basin. Keywords: Categorical Bayesian Maximum Entropy method, Lithological Classification, Hydrogeological Setting

Islas Marias Archipelago, Mexico. A Missing Piece to Reconstruct the Paleoposition of Baja California

NASA Astrophysics Data System (ADS)

Schaaf, P. E.; Pompa, V.; Hernandez, T.; Weber, B.; Solis, G.; Villanueva, D.; Perez-Venzor, J.

2011-12-01

Paleopositions for southern Baja California peninsula have yielded controversial models over the past 30 years. Mainly based on paleomagnetic data many hypotheses place Baja at lower paleolatitudes in front of southern Mexico or Central America with subsequent northward translations. Other models suggest minor, if any, northward displacements with respect to continental Mexico combined with clockwise rotations. Lithological, geochemical, and geochronological similarities for southern Baja California and Puerto Vallarta (western Mexico Pacific margin) igneous rocks seem to confirm the latter model. To further prove this model we have mapped and collected rocks from Maria Madre, the largest island of the Islas Marias archipelago, located in the mouth of the Gulf of California. In an area of only 145 square kilometers, metamorphic basements rocks (ortho and migmatitic gneisses), highly deformed metasediments, granitoids, acid to intermediate volcanic sequences, and a cover with gently folded marine sediments are exposed. The basement complex with gneisses and metasediments, including garnet-bearing paragneiss and calc silicates, as well as the granodioritic-tonalitic intrusives display an extraordinary accordance with similar units observed in the Los Cabos Block (LCB) of Baja California Sur. Furthermore, U-Pb zircon ages of 162 and 170 Ma for the basement gneisses and of 80 Ma for the granitoids have been reported also from the LCB. Additionally, upper Cretaceous intrusive ages are well known from the Puerto Vallarta batholith in Jalisco and Nayarit, mainland Mexico. Geochemical and isotopic data as well as Nd model ages confirm a magmatic consanguinity of LCB, Islas Marias, and Puerto Vallarta granitoids. The volcanic units of Maria Madre Island include ignimbrites and effusive dacitic-rhyolithic rocks, which can be correlated to the Sierra Madre Occidental province and the Comundú Formation of Baja California. Age determinations are under work to confirm this hypothesis. Finally, the sedimentary cover record several subsidence and uplift events, possibly related to the opening of the Gulf of California. Micropaleontological investigations on Neogene deposits give evidence for an above sea level position of the islands since the late Pleistocene. In summary, our new lithological, geochemical, and geochronological investigations on the Isla María Madre rock suite confirm a common magmatic arc parenthood of these units with respect to mainland Mexico at latitudes of Puerto Vallarta and with the LCB of Baja California Sur. Large paleolatitudal displacements of Baja can be discarded from these results.

Early cretaceous rift sediments of the Gabon-Congo margin: lithology and organic matter; tectonic and paleogeothermal evolution

NASA Astrophysics Data System (ADS)

Robert, P.; Yapaudjian, L.

The active troughs of the western Gabon-Congo margin which are part of the South Atlantic rift contain a Neocomian to barremian-aged fluvial-lacustrine series. The lithological sequence of interbedded clastic and pelitic formations constitutes a well-defined cycle. This cycle is divided into: a fluvial or piedmont stage, a lacustrine turbidite-stage corresponding to the distension paroxysm of the basin, and finally, a lacustrine deltaic stage of infilling and tectonic quiescence. The organic matter included in the shale layers is abundant and originates mainly from lacustrine Botryococcus algae and their alteration and secretion products. The geothermal history of the basin, demonstrated by the evolution of the organic matter indicates a strong hyperthermy located in the active, more subsiding part of the basin, and contemporaneous with sedimentation.

The Shaw meteorite - History of a chondrite consisting of impact-melted and metamorphic lithologies

NASA Technical Reports Server (NTRS)

Taylor, G. J.; Keil, K.; Berkley, J. L.; Lange, D. E.; Fodor, R. V.

1979-01-01

Three intermingled lithologies are identified in the Shaw L-group chondrite: a light-colored lithology with a poikilitic texture, consisting of olivine and augite crystals surrounded by larger orthopyroxene grains; a dark-colored lithology containing remnant chondrules and exhibiting a microgranular texture; and a gray lithology which appears to be intermediate between the other two. Contrary to published opinions, the Shaw meteorite contains normal L-group chondrite abundances of metal and troilite, though these phases are irregularly distributed. The lithological analyses suggest that 4.52 Byr ago an impact took place on the L-group chondrite parent object of Shaw.

Automated lithology prediction from PGNAA and other geophysical logs.

PubMed

Borsaru, M; Zhou, B; Aizawa, T; Karashima, H; Hashimoto, T

2006-02-01

Different methods of lithology predictions from geophysical data have been developed in the last 15 years. The geophysical logs used for predicting lithology are the conventional logs: sonic, neutron-neutron, gamma (total natural-gamma) and density (backscattered gamma-gamma). The prompt gamma neutron activation analysis (PGNAA) is another established geophysical logging technique for in situ element analysis of rocks in boreholes. The work described in this paper was carried out to investigate the application of PGNAA to the lithology interpretation. The data interpretation was conducted using the automatic interpretation program LogTrans based on statistical analysis. Limited test suggests that PGNAA logging data can be used to predict the lithology. A success rate of 73% for lithology prediction was achieved from PGNAA logging data only. It can also be used in conjunction with the conventional geophysical logs to enhance the lithology prediction.

Mineralogy, Reflectance Spectra, and Physical Properties of the Chelyabinsk LL5 Chondrite - Insight Into Shock Induced Changes in Asteroid Regoliths

NASA Astrophysics Data System (ADS)

Gritsevich, Maria; Muinonen, Karri; Kohout, Tomas; Grokhovsky, Victor; Yakovlev, Grigoriy; Haloda, Jakub; Halodova, Patricie; Michallik, Radoslaw; Penttilä, Antti

On February 15, 2013, at 9:22 am, an exceptionally bright and long duration fireball was observed by many eyewitnesses in the Chelyabinsk region, Russia. Two days later the first fragments of the Chelyabinsk meteorite were reported to be found in the area, located approximately 40 km south of Chelyabinsk. We have examined a large number of the recovered Chelyabinsk meteorite fragments. Three lithologies, the light-colored, dark-colored, and impact melt, were found within the recovered meteorites. The light colored lithology is a LL5 ordinary chondrite (Fa 28, Fs 23) shocked to S4 level. The dark colored lithology is of identical LL5 composition (Fa 28, Fs 23). However, it is shocked to higher level (shock-darkened) with fine grained metal and sulfide-rich melt forming a dense network of fine veins impregnating the inter- and intra-granular pore space within crushed silicate grains. The impact melt lithology is a whole-rock melt derived from the same LL5 source material and is present within the light-colored and dark-colored lithology as inter-granular veins. The measured bulk and grain densities and the porosity closely resemble other LL chondrites. Based on the magnetic susceptibility, the Chelyabinsk meteorites are richer in metallic iron as compared to database of other LL chondrites. All three Chelyabinsk lithologies are of identical LL5 composition and origin. Both impact melting and shock darkening cause a decrease in reflectance and a suppression of the silicate absorption bands in the reflectance spectra. Such spectral changes are similar to the space weathering effects observed on asteroids. However, space weathering of chondritic materials is often accompanied with a significant spectral slope change (reddening). In our case, only negligible to minor change in the spectral slope is observed. Thus, it is possible that some dark asteroids with invisible silicate absorption bands may be composed of relatively fresh shock-darkened chondritic material. The main spectral difference of chondritic asteroid surfaces dominated by impact melt, shock darkening, or space weathering, is a significant spectral slope change in the latter case. Thus, shock does not have significant effect on meteorite properties, but causes spectral darkening and suppression of silicate absorption bands.

Preliminary development of the LBL/USGS three-dimensional site-scale model of Yucca Mountain, Nevada

USGS Publications Warehouse

1995-01-01

A three-dimensional model of moisture flow within the unsaturated zone at Yucca Mountain is being developed at Lawrence Berkeley Laboratory (LBL) in cooperation with the U.S. Geological Survey (USGS). This site-scale model covers and area of about 34 km2 and is bounded by major faults to the north, east and west. The model geometry is defined (1) to represent the variations of hydrogeological units between the ground surface and the water table; (2) to be able to reproduce the effect of abrupt changes in hydrogeological parameters at the boundaries between hyrdogeological units; and (3) to include the influence of major faults. A detailed numerical grid has been developed based on the locations of boreholes, different infiltration zones, hydrogeological units and their outcrops, major faults, and water level data. Contour maps and isopatch maps are presented defining different types of infiltration zones, and the spatial distribution of Tiva Canyon, Paintbrush, and Topopah Spring hydrogeological units. The grid geometry consists of seventeen non-uniform layers which represent the lithological variations within the four main welded and non-welded hydrogeological units. Matrix flow is approximated using the van Genuchten model, and the equivalent continuum approximation is used to account for fracture flow in the welded units. The fault zones are explicitly modeled as porous medium using various assumptions regarding their permeabilities and characteristic curves. One-, two-, and three-dimensional simulations are conducted using the TOUGH2 computer program. Steady-state simulations are performed with various uniform and non-uniform infiltration rates. The results are interpreted in terms of the effect of fault characteristics on the moisture flow distribution, and on location and formation of preferential pathways.

Hydrostratigraphic mapping of the Milford-Souhegan glacial drift aquifer, and effects of hydrostratigraphy on transport of PCE, Operable Unit 1, Savage Superfund Site, Milford, New Hampshire

USGS Publications Warehouse

Harte, Philip T.

2010-01-01

The Savage Municipal Well Superfund site in the Town of Milford, New Hampshire, was underlain by a 0.5-square mile plume (as mapped in 1994) of volatile organic compounds (VOCs), most of which consisted of tetrachloroethylene (PCE). The plume occurs mostly within highly transmissive stratified-drift deposits but also extends into underlying till and bedrock. The plume has been divided into two areas called Operable Unit 1 (OU1), which contains the primary source area, and Operable Unit 2 (OU2), which is defined as the extended plume area outside of OU1. The OU1 remedial system includes a low-permeability barrier wall that encircles the highest detected concentrations of PCE and a series of injection and extraction wells to contain and remove contaminants. The barrier wall likely penetrates the full thickness of the sand and gravel; in many places, it also penetrates the full thickness of the underlying basal till and sits atop bedrock.From 1998 to 2004, PCE concentrations decreased by an average of 80 percent at most wells outside the barrier wall. However, inside the barrier, PCE concentrations greater than 10,000 micrograms per liter (μg/L) still exist (2008). The remediation of these areas of recalcitrant PCE presents challenges to successful remediation.The U.S. Geological Survey (USGS), in cooperation with the New Hampshire Department of Environmental Services (NHDES) and the U.S. Environmental Protection Agency (USEPA), Region 1, is studying the solute transport of VOCs (primarily PCE) in contaminated groundwater in the unconsolidated sediments (overburden) of the Savage site and specifically assisting in the evaluation of the effectiveness of remedial operations in the OU1 area. As part of this effort, the USGS analyzed the subsurface stratigraphy to help understand hydrostratigraphic controls on remediation.A combination of lithologic, borehole natural gamma-ray and electromagnetic (EM) induction logging, and test drilling has identified 11 primary hydrostratigraphic units in OU1. These 11 units consist of several well-sorted sandy layers with some gravel that are separated by poorly sorted cobble layers with a fine-grained matrix. Collectively these units represent glacial sediments deposited by localized ice-margin fluctuations. For the most part, the units are semi-planar, particularly the cobble units, and truncated by an undulating bedrock surface. The lowermost unit is a basal till that ranges in thickness from zero to greater than 10 feet and mantles the bedrock surface.The 11 units have different lithologic and hydraulic characteristics. The hydraulic conductivity of the well-sorted sand and gravel units is typically greater than the conductivity of the poorly sorted cobble units and the basal till. The hydraulic conductivity ranges from 5 to greater than 500 feet per day. Lateral and vertical variation in lithology and hydraulic conductivity are inferred by variations in borehole natural gamma-ray counts and estimates of hydraulic conductivity.The comparison of hydrostratigraphic units with the spatial distribution of PCE concentrations suggests that solute transport away from source areas is primarily lateral within the permeable sandy units in the middle to lower parts of the aquifer. Along the centerline of the interior barrier area, highest PCE concentrations are in the sandy units to the east of suspected source areas.

Discriminating the Mineralogical Composition in Drill Cuttings Based on Absorption Spectra in the Terahertz Range.

PubMed

Miao, Xinyang; Li, Hao; Bao, Rima; Feng, Chengjing; Wu, Hang; Zhan, Honglei; Li, Yizhang; Zhao, Kun

2017-02-01

Understanding the geological units of a reservoir is essential to the development and management of the resource. In this paper, drill cuttings from several depths from an oilfield were studied using terahertz time domain spectroscopy (THz-TDS). Cluster analysis (CA) and principal component analysis (PCA) were employed to classify and analyze the cuttings. The cuttings were clearly classified based on CA and PCA methods, and the results were in agreement with the lithology. Moreover, calcite and dolomite have stronger absorption of a THz pulse than any other minerals, based on an analysis of the PC1 scores. Quantitative analyses of minor minerals were also realized by building a series of linear and non-linear models between contents and PC2 scores. The results prove THz technology to be a promising means for determining reservoir lithology as well as other properties, which will be a significant supplementary method in oil fields.

Feldspathic Clasts in Yamato 86032: Remnants of the Lunar Crust with Implications for its Formation and Impact History

NASA Technical Reports Server (NTRS)

Nyquist, L.; Bogard, D.; Yamaguchi, A.; Shih, C.-Y.; Ebihara, M.; Reese, Y.; Garrison, D.; Takeda, H.

2006-01-01

Yamato (Y)-86032 is a relatively large, feldspathic lunar highlands meteorite composed of a variety of highland lithologies. Low bulk contents of Th and Fe indicated that it came from a region of the moon far distant from the Procellarum KREEP Terrain (PKT) and the Apollo landing sites, perhaps from the farside. A large (5.2 x 3.6 cm) slab was cut from Y-86032 . We report results from coordinated textural, mineralogical-petrological, chemical, and isotopic studies of lithologies identified in the slab, emphasizing the results of Ar-39/Ar-40, Rb-Sr, and Sm-Nd chronological studies as well as Sm-isotopic studies. These studies characterize the history of Y-86032 and its precursors in the farside mega-regolith, leading to inferences about the formation and evolution of the lunar crust. Textural studies establish that the Y-86032 breccia is composed of a variety of highland components including feldspathic breccias, and other components, such as possible VLT mare basalts. Impact melt veins smoothly abut the other lithologies. Thus, Y-86032 experienced at least two impact events. These impacts occurred on a predominantly feldspathic protolith, which formed 4.43+/-0.03 Ga ago as determined from a Sm-Nd isochron for mineral clasts separated from the two dominant lithologies. Initial Nd-143/Nd-144 in the protolith at that time was -0.64+/-0.13 epsilon-units below Nd-143/Nd-144 in reservoirs having chondritic Sm/Nd ratios, consistent with prior fractionation of mafic cumulates from the LMO. Although the mineral chemistry of these clasts differs in detail from that of minerals in Apollo 16 Ferroan Anorthosites (FANs), the Rb-Sr studies establish that the initial Sr-87/Sr-86 in them was the same as in the FANs.

Hydrochemical and water quality assessment of groundwater in Doon Valley of Outer Himalaya, Uttarakhand, India.

PubMed

Dudeja, Divya; Bartarya, Sukesh Kumar; Biyani, A K

2011-10-01

The present study discusses ion sources and assesses the chemical quality of groundwater of Doon Valley in Outer Himalayan region for drinking and irrigational purposes. Valley is almost filled with Doon gravels that are main aquifers supplying water to its habitants. Recharged only by meteoric water, groundwater quality in these aquifers is controlled essentially by chemical processes occurring between water and lithology and locally altered by human activities. Seventy-six water samples were collected from dug wells, hand pumps and tube wells and were analysed for their major ion concentrations. The pH is varying from 5.6 to 7.4 and electrical conductivity from 71 to 951 μmho/cm. Groundwater of Doon valley is dominated by bicarbonate contributing 83% in anionic abundance while calcium and magnesium dominate in cationic concentrations with 88%. The seasonal and spatial variation in ionic concentration, in general, is related to discharge and lithology. The high ratio of (Ca + Mg)/(Na + K), i.e. 10, low ratio of (Na + K)/TZ+, i.e.0.2 and also the presence of carbonate lithology in the northern part of valley, is indicative of carbonate dissolution as the main controlling solute acquisition process in the valley. The low abundance of silica content and high HCO₃/H₄SiO₄ ratio also supports carbonate dissolution and less significant role of silicate weathering as the major source for dissolved ions in Doon Valley. The analytical results computed for various indices show that water is of fairly good quality, although, hard but have moderate dissolved solid content. It is free from sodium hazard lying in C₁-S₁ and C₂-S₁ class of USSL diagram and in general suitable for drinking and irrigation except few locations having slightly high salinity hazard.

Geologic map of the Valjean Hills 7.5' quadrangle, San Bernardino County, California

USGS Publications Warehouse

Calzia, J.P.; Troxel, Bennie W.; digital database by Raumann, Christian G.

2003-01-01

FGDC-compliant metadata for the ARC/INFO coverages. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Geologic Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Even though this is an Open-File Report and includes the standard USGS Open-File disclaimer, the report closely adheres to the stratigraphic nomenclature of the U.S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3 above) or plotting the postscript file (2 above).

Contributions to the geology of uranium and thorium by the United States Geological Survey and Atomic Energy Commission for the United Nations International Conference on Peaceful Uses of Atomic Energy, Geneva, Switzerland, 1955

USGS Publications Warehouse

Page, Lincoln R.; Stocking, Hobart E.; Smith, Harriet B.

1956-01-01

Within the boundaries of the United States abnormal amounts of uranium have been found in rocks of nearly all geologic ages and lithologic types. Distribution of ore is more restricted. On the Colorado Plateau, the Morrison formation of Jurassic age yields 61.4 percent of the ore produced in the United States, and the Chinle conglomerate and Shinarump formation of Triassic age contribute 26.0 and 5.8 percent, respectively. Clastic, carbonaceous, and carbonate sedimentary rocks of Tertiary, Mesozoic, and Paleozoic ages and veins of Tertiary age are the source of the remaining 6.8 percent.

Recommended procedures and techniques for the petrographic description of bituminous coals

USGS Publications Warehouse

Chao, E.C.T.; Minkin, J.A.; Thompson, C.L.

1982-01-01

Modern coal petrology requires rapid and precise description of great numbers of coal core or bench samples in order to acquire the information required to understand and predict vertical and lateral variation of coal quality for correlation with coal-bed thickness, depositional environment, suitability for technological uses, etc. Procedures for coal description vary in accordance with the objectives of the description. To achieve our aim of acquiring the maximum amount of quantitative information within the shortest period of time, we have adopted a combined megascopic-microscopic procedure. Megascopic analysis is used to identify the distinctive lithologies present, and microscopic analysis is required only to describe representative examples of the mixed lithologies observed. This procedure greatly decreases the number of microscopic analyses needed for adequate description of a sample. For quantitative megascopic description of coal microlithotypes, microlithotype assemblages, and lithotypes, we use (V) for vitrite or vitrain, (E) for liptite, (I) for inertite or fusain, (M) for mineral layers or lenses other than iron sulfide, (S) for iron sulfide, and (X1), (X2), etc. for mixed lithologies. Microscopic description is expressed in terms of V representing the vitrinite maceral group, E the exinite group, I the inertinite group, and M mineral components. volume percentages are expressed as subscripts. Thus (V)20(V80E10I5M5)80 indicates a lithotype or assemblage of microlithotypes consisting of 20 vol. % vitrite and 80% of a mixed lithology having a modal maceral composition V80E10I5M5. This bulk composition can alternatively be recalculated and described as V84E8I4M4. To generate these quantitative data rapidly and accurately, we utilize an automated image analysis system (AIAS). Plots of VEIM data on easily constructed ternary diagrams provide readily comprehended illustrations of the range of modal composition of the lithologic units making up a given coal bed. The use of bulk-specific-gravity determinations is alo recommended for identification and characterization of the distinctive lithologic units. The availability of an AIAS also enhances the capability to acquire textural information. Ranges of size of maceral and mineral grains can be quickly and precisely determined by use of an AIAS. We assume that shape characteristics of coal particles can also be readily evaluated by automated image analysis, although this evaluation has not yet been attempted in our laboratory. Definitive data on the particulate mineral content of coal constitute another important segment of petrographic description. Characterization of mineral content may be accomplished by optical identification, electron microprobe analysis, X-ray diffraction, and scanning and transmission electron microscopy. Individual mineral grains in place in polished blocks or polished this sections, or separated from the coal matrix by sink-float methods are studied by analytical techniques appropriate to the conditions of sampling. Finally, whenever possible, identification of the probable genus or plant species from which a given coal component is derived will add valuable information and meaning to the petrographic description. ?? 1982.

The bedrock electrical conductivity structure of Northern Ireland

NASA Astrophysics Data System (ADS)

Beamish, David

2013-08-01

An airborne geophysical survey of the whole of Northern Ireland has provided over 4.8 M estimates of the bedrock conductivity over the wide range of geological formations present. This study investigates how such data can be used to provide additional knowledge in relation to existing digital geological map information. A by-product of the analysis is a simplification of the spatially aggregated information obtained in such surveys. The methodology used is a GIS-based attribution of the conductivity estimates using a lithological classification of the bedrock formations. A 1:250k geological classification of the data is performed leading to a 56 unit lithological and geostatistical analysis of the conductivity information. The central moments (medians) of the classified data are used to provide a new digital bedrock conductivity map of Northern Ireland with values ranging from 0.32 to 41.36 mS m-1. This baseline map of conductivities displays a strong correspondence with an existing 4 quadrant, chrono-geological description of Northern Ireland. Once defined, the baseline conductivity map allows departures from the norm to be assessed across each specific lithological unit. Bulk electrical conductivity is controlled by a number of petrophysical parameters and it is their variation that is assessed by the procedures employed. The igneous rocks are found to display the largest variability in conductivity values and many of the statistical distributions are multi-modal. A sequence of low-value modes in these data are associated with intrusives within volcanic complexes. These and much older Neoproterzoic rocks appear to represent very low porosity formations that may be the product of rapid cooling during emplacement. By way of contrast, extensive flood basalts (the Antrim lavas) record a well-defined and much higher median value (12.24 mS m-1) although they display complex spatial behaviour in detail. Sedimentary rocks appear to follow the broad behaviours anticipated by standard theoretical descriptions of rock electrical properties that allow for a term due to grain surface conduction (e.g. the presence of clay). Single lithology sedimentary rocks are represented by an increasing set of conductivities through the sequence sandstone (4.91 mS m-1), limestone (8.41 mS m-1) and mudstone (17.85 mS m-1) with argillaceous rocks providing a conductivity of 41.1 mS m-1. In the case of both sandstone and limestone, the single lithology conductivities are significantly less than their mixed lithology counterparts. Mudrocks display a bimodal statistical distribution and an extended analysis of these rocks is carried out across a Carboniferous basin. The results clearly indicate that non-shale mudstones are distinctly less conductive than their shale counterparts. Shale formations display rapid and large movements in conductivity and it is suggested that the observed sensitivity may be due to competing surface conduction effects due to clay and organic material. A study of the variation of conductivity with geological period is also performed. Both a decreasing trend with age and a modulation that peaks in the Triassic period are observed.

Estimation and mapping of uranium content of geological units in France.

PubMed

Ielsch, G; Cuney, M; Buscail, F; Rossi, F; Leon, A; Cushing, M E

2017-01-01

In France, natural radiation accounts for most of the population exposure to ionizing radiation. The Institute for Radiological Protection and Nuclear Safety (IRSN) carries out studies to evaluate the variability of natural radioactivity over the French territory. In this framework, the present study consisted in the evaluation of uranium concentrations in bedrocks. The objective was to provide estimate of uranium content of each geological unit defined in the geological map of France (1:1,000,000). The methodology was based on the interpretation of existing geochemical data (results of whole rock sample analysis) and the knowledge of petrology and lithology of the geological units, which allowed obtaining a first estimate of the uranium content of rocks. Then, this first estimate was improved thanks to some additional information. For example, some particular or regional sedimentary rocks which could present uranium contents higher than those generally observed for these lithologies, were identified. Moreover, databases on mining provided information on the location of uranium and coal/lignite mines and thus indicated the location of particular uranium-rich rocks. The geological units, defined from their boundaries extracted from the geological map of France (1:1,000,000), were finally classified into 5 categories based on their mean uranium content. The map obtained provided useful data for establishing the geogenic radon map of France, but also for mapping countrywide exposure to terrestrial radiation and for the evaluation of background levels of natural radioactivity used for impact assessment of anthropogenic activities. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fault geometries and deformation mechanisms in the evolution of low-angle normal faults (Kea, Greece)

NASA Astrophysics Data System (ADS)

Iglseder, C.; Grasemann, B.; Schneider, D.; Rice, A. H. N.; Stöckli, D.; Rockenschaub, M.

2009-04-01

The overall tectonic regime in the Cyclades since the Oligocene has been characterized by crustal extension, accommodated by movements on low-angle normal faults (LANFs). On Kea, structural investigations have demonstrated the existence of an island-wide LANF within a large-scale ductile-brittle shear-zone traceable over a distance of 19.5 km parallel to the stretching lineation. The tectonostratigraphy comprises Attic-Cycladic Crystalline lithologies with a shallowly-dipping schist-calcite marble unit overlain by calcitic and dolomitic fault rocks. Notably, the calcitic marbles have been mylonitized, with a mean NNE/NE-SSW/SW trending, pervasive stretching lineation and intense isoclinal folding with fold axes parallel to the stretching lineation. Numerous SC-SCĆ-fabrics and monoclinic clast-geometries show a consistent top-to-SSW shear-sense. Recorded within all lithologies is a consistent WNW/NW-ESE/SE and NNE/NE-SSW/SW striking network of conjugated brittle, brittle-ductile high-angle faults perpendicular and (sub)parallel to the main stretching direction. Field evidence and microstructural investigations indicate high-angle normal faults formed synchronously with movement on LANFs. This interplay of LANFs with high-angle structures, initiated and evolved from brittle-ductile to brittle conditions, indicates initial stages of movement below the calcite brittle-ductile transition but above the dolomite transition. Weakening processes related to syntectonic fluid-rock interactions highlight these observations. In particular, grain-size reduction and strain localisation in fine-grained (ultra)-cataclasites and fine-grained aggregates of phyllosilicate-rich fault-rocks promoted fluid-flow and pressure-solution-accommodated ‘frictional-viscous' creep. These mechanisms show the importance for LANF slip and movement in the progressive development and interaction between contemporaneous active normal faults in the Andersonian-Byerlee frictional mechanics.

Discrimination of Sedimentary Lithologies Through Unmixing of EO-1 Hyperion Data: Melville Island, Canadian High Arctic

NASA Astrophysics Data System (ADS)

Leverington, D. W.

2008-12-01

The use of remote-sensing techniques in the discrimination of rock and soil classes in northern regions can help support a diverse range of activities including environmental characterization, mineral exploration, and the study of Quaternary paleoenvironments. Images of low spectral resolution can commonly be used in the mapping of lithological classes possessing distinct spectral characteristics, but hyperspectral databases offer greater potential for discrimination of materials distinguished by more subtle reflectance properties. Orbiting sensors offer an especially flexible and cost-effective means for acquisition of data to workers unable to conduct airborne surveys. In an effort to better constrain the utility of hyperspectral datasets in northern research, this study undertook to investigate the effectiveness of EO-1 Hyperion data in the discrimination and mapping of surface classes at a study area on Melville Island, Nunavut. Bedrock units in the immediate study area consist of late-Paleozoic clastic and carbonate sequences of the Sverdrup Basin. Weathered and frost-shattered felsenmeer, predominantly taking the form of boulder- to pebble-sized clasts that have accumulated in place and that mantle parent bedrock units, is the most common surface material in the study area. Hyperion data were converted from at-sensor radiance to reflectance, and were then linearly unmixed on the basis of end-member spectra measured from field samples. Hyperion unmixing results effectively portray the general fractional cover of six end members, although the fraction images of several materials contain background values that in some areas overestimate surface exposure. The best separated end members include the snow, green vegetation, and red-weathering sandstone classes, whereas the classes most negatively affected by elevated fraction values include the mudstone, limestone, and 'other' sandstone classes. Local overestimates of fractional cover are likely related to the shared lithological and weathering characteristics of several clastic and carbonate units, and may also be related to the lower radiometric precision characteristic of Hyperion data. Despite these issues, the databases generated in this study successfully provide useful complementary information to that provided by maps of local bedrock geology.

Lithology and mineralogy recognition from geochemical logging tool data using multivariate statistical analysis.

PubMed

Konaté, Ahmed Amara; Ma, Huolin; Pan, Heping; Qin, Zhen; Ahmed, Hafizullah Abba; Dembele, N'dji Dit Jacques

2017-10-01

The availability of a deep well that penetrates deep into the Ultra High Pressure (UHP) metamorphic rocks is unusual and consequently offers a unique chance to study the metamorphic rocks. One such borehole is located in the southern part of Donghai County in the Sulu UHP metamorphic belt of Eastern China, from the Chinese Continental Scientific Drilling Main hole. This study reports the results obtained from the analysis of oxide log data. A geochemical logging tool provides in situ, gamma ray spectroscopy measurements of major and trace elements in the borehole. Dry weight percent oxide concentration logs obtained for this study were SiO 2 , K 2 O, TiO 2 , H 2 O, CO 2 , Na 2 O, Fe 2 O 3 , FeO, CaO, MnO, MgO, P 2 O 5 and Al 2 O 3 . Cross plot and Principal Component Analysis methods were applied for lithology characterization and mineralogy description respectively. Cross plot analysis allows lithological variations to be characterized. Principal Component Analysis shows that the oxide logs can be summarized by two components related to the feldspar and hydrous minerals. This study has shown that geochemical logging tool data is accurate and adequate to be tremendously useful in UHP metamorphic rocks analysis. Copyright © 2017 Elsevier Ltd. All rights reserved.

High-Resolution Physical Properties Logging of the AND-1B Sediment Core - Opportunity for Detecting High-Frequency Signals of Paleoenvironmental Changes

NASA Astrophysics Data System (ADS)

Niessen, F.; Magens, D.; Kuhn, G.; Helling, D.

2008-12-01

Within the ANDRILL-MIS Project, a more than 1200 m long sediment core, dating back to about 13 Ma, was drilled beneath McMurdo Ice Shelf near Ross Island (Antarctica) in austral summer 2006/07 with the purpose of contributing to a better understanding of the Late Cenozoic history of the Antarctic Ice Sheet. One way to approach past ice dynamics and changes in the paleoenvironment quantitatively, is the analysis of high- resolution physical properties obtained from whole-core multi-sensor core logger measurements in which lithologic changes are expressed numerically. This is especially applicable for the repeating sequences of diatomites and diamictites in the upper half of the core with a prominent cyclicity between 140-300 mbsf. Rather abrupt high-amplitude variations in wet-bulk density (WBD) and magnetic susceptibility (MS) reflect a highly dynamic depositional system, oscillating between two main end-member types: a grounded ice sheet and open marine conditions. For the whole core, the WBD signal, ranging from 1.4 kg/cu.m in the diatomites to 2.3 kg/cu.m in diamictites from the lower part of the core, represents the influence of three variables: (i) the degree of compaction seen as reduction of porosities with depth of about 30 % from top to bottom, (ii) the clast content with clasts being almost absent in diatomite deposits and (iii) the individual grain density (GD). GD itself strongly reflects the variety of lithologies as well as the influence of cement (mainly pyrite and carbonate) on the matrix grain density. The calculation of residual porosities demonstrates the strong imprint of glacial loading for especially diamictites from the upper 150 m, pointing to a significant thickness of the overriding Pleistocene ice sheet. MS on the other hand mainly documents a marine vs. terrestrial source of sediments where the latter can be divided into younger local material from the McMurdo Volcanic Province and basement clasts from the Transantarctic Mountains. Values range over several orders of magnitude from <10 (10-5 SI) in the diatomites to 8000 (10-5 SI) in single clasts (mainly dolerite). Synchronous minima and maxima in both WBD and MS support dramatic changes in the depositional environment, driven by oscillations in ice extent in response to global climate fluctuations on orbital timescales. Superimposed on this, small-amplitude variations of high frequency are found within diatomite units. A rhythmic pattern of probably millennial to centennial pacing proposes an additional non-orbital forcing as control on system dynamics, at least during interglacials.

3-D-Observation of Matrix of MIL 090657 Meteorite by Absorption-Phase Tomography

NASA Technical Reports Server (NTRS)

Miyama, Sugimoto; Tsuchiyama, Akira; Matsuno, Junya; Miyake, Akira; Nakano, Tsukasa; Uesugi, Kentaro; Takeuchi, Akihisa; Takigawa, Aki; Takayama, Akiko; Nakamura-Messenger, Keiko;

Origin and mechanisms of high salinity in Hombolo Dam and groundwater in Dodoma municipality Tanzania, revealed

NASA Astrophysics Data System (ADS)

Shemsanga, Ceven; Muzuka, Alfred Nzibavuga Nyarubakula; Martz, Lawrance; Komakech, Hans Charles; Elisante, Eliapenda; Kisaka, Marry; Ntuza, Cosmas

2017-10-01

The Hombolo dam (HD), in central Tanzania, is a shallow reservoir characterized by high salinity that limits its use for human activities. The origin of the salinity, mechanisms of reaching and concentrating in the dam remain unclear. These were assessed using hydrogeochemical facies, water type evolutions and mapping. The source of HD salinity was identified to be shallow groundwater (SG) and runoff from a seasonal floodplain with NaCl-rich lithological materails, along Little Kinyasungwe River that feeds the dam. The NaCl-rich lithological units, about 5-7 km upstream of the dam, were highly concentrated with NaCl to the extent that the local community was commercially separating table salt from them. The physicochemical parameters from these NaCl-rich lithological materials were well represented in HD and nearby groundwater sources, which suggests active water interactions. Water type evolution and surface hydrology assessments clearly showed that SG in the salty-floodplain was influenced by evaporation (ET) and was periodically carried to the HD. Clearly; HD water had high chemical similarity with the nearby SG. This agrees with previous studies that HD is partly fed by the local aquifer. However, this is the first attempt at mapping its physical origin. The origin of HD salinity was further supported by the spatial distribution of electrical conductivity (EC), where very high EC (up to 21,230 μScm-1) was recorded in SG within the NaCl-rich lithological unit while water sources far away from the NaCl-rich materials had much lower EC values. Thus, the study disagrees with previous conclusions that HD salinity was sorely due to high dam surface ET but is primarily due to geological reasons. Comparisons of HD with a nearby Matumbulu dam (MD), another earthen dam in climatologically similar settings, reveals that MD water was less saline/mineralised. This further shows that HD high salinity is most likely a geologic phenomenon, but local climatic factors, namely high ET, decreasing rainfall and warming trends are likely to have concentrated the salts further. Although HD is widely/ideally used for grape vine irrigation, it was clearly revealed that its prolonged usage would potentially affect the soil and grape productivity due to high salinity.

Geological Features Mapping Using PALSAR-2 Data in Kelantan River Basin, Peninsular Malaysia

NASA Astrophysics Data System (ADS)

Pour, A. B.; Hashim, M.

2016-09-01

In this study, the recently launched Phased Array type L-band Synthetic Aperture Radar-2 (PALSAR-2) onboard the Advanced Land Observing Satellite-2 (ALOS-2), remote sensing data were used to map geologic structural and topographical features in the Kelantan river basin for identification of high potential risk and susceptible zones for landslides and flooding areas. A ScanSAR and two fine mode dual polarization level 3.1 images cover Kelantan state were processed for comprehensive analysis of major geological structures and detailed characterizations of lineaments, drainage patterns and lithology at both regional and district scales. Red-Green-Blue (RGB) colour-composite was applied to different polarization channels of PALSAR-2 data to extract variety of geological information. Directional convolution filters were applied to the data for identifying linear features in particular directions and edge enhancement in the spatial domain. Results derived from ScanSAR image indicate that lineament occurrence at regional scale was mainly linked to the N-S trending of the Bentong-Raub Suture Zone (BRSZ) in the west and Lebir Fault Zone in the east of the Kelantan state. Combination of different polarization channels produced image maps contain important information related to water bodies, wetlands and lithological units for the Kelantan state using fine mode observation data. The N-S, NE-SW and NNE-SSW lineament trends were identified in the study area using directional filtering. Dendritic, sub-dendritic and rectangular drainage patterns were detected in the Kelantan river basin. The analysis of field investigations data indicate that many of flooded areas were associated with high potential risk zones for hydro-geological hazards such as wetlands, urban areas, floodplain scroll, meander bend, dendritic and sub-dendritic drainage patterns, which are located in flat topograghy regions. Numerous landslide points were located in rectangular drainage system that associated with topographic slope of metamorphic and Quaternary rock units. Some large landslides were associated with N-S, NNE-SSW and NE-SW trending fault zones. Consequently, structural and topographical geology maps were produced for Kelantan river basin using PALSAR-2 data, which could be broadly applicable for landslide hazard mapping and identification of high potential risk zone for hydro-geological hazards.

Preliminary geologic map of the Piru 7.5' quadrangle, southern California: a digital database

USGS Publications Warehouse

Yerkes, R.F.; Campbell, Russell H.

1995-01-01

This Open-File report is a digital geologic map database. This pamphlet serves to introduce and describe the digital data. There is no paper map included in the Open-File report. This digital map database is compiled from previously published sources combined with some new mapping and modifications in nomenclature. The geologic map database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U. S. Geological Survey. For detailed descriptions of the units, their stratigraphic relations and sources of geologic mapping consult Yerkes and Campbell (1995). More specific information about the units may be available in the original sources.

[Chemical composition and daily variation of melt water during ablation season in monsoonal temperate Glacier region: a case study of Baishui Glacier No. 1].

PubMed

Zhu, Guo-Feng; Pu, Tao; He, Yuan-Qing; Wang, Pei-Zhen; Kong, Jian-Long; Zhang, Ning-Ning; Xin, Hui-Juan

2012-12-01

Melt water samples collected continuously from 29 August to 3 September 2009 in the Baishui Glacier No. 1 at elevation of 4750 m were analyzed for pH, conductivity, delta18O and inorganic ions. The results showed that the pH had obvious diurnal variations and was increased slightly by the influence of precipitation. The dissolution of alkaline soluble salts in the dust was the main reason for the increase of melt water conductivity; the value of delta18O was relatively low in strong ablation period and high in slight ablation period. Different from other research areas, the concentrations of Na+, K+, which were influenced by lithological and marine water vapor, were higher than that of Mg2+ in the study area; HCO3- and Ca2+ accounted for more than 80% of total ions in snow and ice melt water, indicating that the ions mainly came from limestone and the melt water was a typical carbonate solution; The content of melt water had an obvious daily change with temperature change, but the response amplitudes were different; Monsoon transport, local rock lithology, human industrial and agricultural activities were the main sources of inorganic ions and the deciding factors of the ion composition in the Baishui Glacier No. 1.

A Cabonaceous Chondrite Dominated Lithology from the HED Parent; PRA 04401

NASA Technical Reports Server (NTRS)

Herrin, Jason S.; Zolensky, M. E.; Mittlefehldt, David W.

2010-01-01

The paired howardite breccias Mt. Pratt (PRA) 04401 and PRA 04402 are notable for their high proportion of carbonaceous chondrite clasts [1]. They consist predominantly of coarse (0.1-7 mm) diogenite (orthopyroxene), eucrite (plagioclase + pyroxene), and carbonaceous chondrite clasts set in a finer grained matrix of these same materials. Coarse C-chondrite clasts up to 7 mm are composed mainly of fine-grained phyllosilicates with lesser sulfides and high-mg# anhydrous magnesian silicates. Most of these clasts appear to be texturally consistent with CM2 classification [1] and some contain relict chondrules. The clasts are angular and reaction or alteration textures are not apparent in the surrounding matrix. PRA 04401 contains about 70 modal% C-chondrite clasts while PRA 04402 contains about 7%. Although many howardites are known to contain abundant C-chondrite clasts [2,3,4], PRA 04401 is, to our knowledge, the most chondrite-rich howardite lithology identified to date. Low EPMA totals from CM2-type clasts in other howardites suggest that they frequently contain 10 wt% or more water [2], a figure consistent with their mineralogy. PRA 04401, therefore, demonstrates the potential for hydrous lithologies with greater than 5 wt% water to occur locally within the nominally anhydrous HED parent body. Since the origin of this water is xenogenic, it might therefore be concentrated in portions of the asteroid surface where it would be more readily observable by remote sensing techniques. We plan to further examine C-chondrite clasts in PRA 04401/2 with the intent of establishing firm chemical classification, estimating water content, and evaluating their relationship with the host breccia. To help place them in context of the HED parent, we will also compare these breccias with other howardites to evaluate which lithologies are likely to be more prevalent on the asteroid surface.

Evaluation of the ground-water resources of parts of Lancaster and Berks Counties, Pennsylvania

USGS Publications Warehouse

Gerhart, J.M.; Lazorchick, G.J.

1984-01-01

Secondary openings in bedrock are the avenues for virtually all ground-water flow in a 626-sqare-mile area in Lancaster and Berks Counties, Pennsylvania. The number, size, and interconnection of secondary openings are functions of lithology, depth, and topography. Ground water actively circulates to depths of 150 to 300 feet below land surface. Total average annual ground-water recharge for the area is 388 million gallons per day, most of which discharges to streams from local, unconfined flow systems. A digital ground-water flow model was developed to simulate unconfined flow under several different recharge and withdrawal scenarios. On the basis of lithologic and hydrologic differences, the modeled area was sub-divided into 22 hydrogeologic units. A finite-difference grid with rectangular blocks, each 2,015 by 2,332 feet, was used. The model was calibrated under steady-state and transient conditions. The steady-state calibration was used to determine hydraulic conductivities and stream leakage coefficients and the transient calibration was used to determine specific yields. The 22 hydrogeologic units fall into four general lithologies: Carbonate rocks, metamorphic rocks, Paleozoic sedimentary rocks, and Triassic sedimentary rocks. Average hydraulic conductivity ranges from about 8.8 feet per day in carbonate units to about .5 feet per day in metamorphic units. The Stonehenge Formation (limestone) has the greatest average hydraulic conductivity--85.2 feet per day in carbonate units to about 0.11 feet per day in the greatest gaining-strem leakage coefficient--16.81 feet per day. Specific yield ranges from 0.06 to 0.09 in carbonate units, and is 0.02 to 0.015, and 0.012 in metamorphic, Paleozoic sedimentary, and Triassic sedimentary units, respectively. Transient simulations were made to determine the effects of four different combinations of natural and artificial stresses. Natural aquifer conditions (no ground-water withdrawals) and actual aquifer conditions (current ground-water withdrawals) were simulated for two years under normal seasonal and hypothetical drought (60-percent reduction in winter-spring recharge) conditions. In October, 6 months after the hypothetical drought, simulated declines in water-table altitude due to the drought occurred everywhere and ranged from a median of 3.6 feet in carbonate units to 8.7 feet in carbonate units. Simulated base flows for five major streams were reduced by 33 to 51 percent during the hypothetical drought. Also in October, maximum simulated declines in water-table altitude due to ground-water withdrawls ranged from 33 feet in carbonate units to 79 feet in Triassic sedimentary units. Simulated base flows for five major streams were reduced by the amount of ground water withdrawn. Finally, again in October, maximum simulated declines in water-table altitude due to the combination of hypothetical drought and ground-water withdrawls ranged from 38 feet in carbonate units to 109 feet in Triassic sedimentary units. Due to aquifer dewatering, simulated declines were as much as 24 feet greater than the sum of the separate simulated declines that were caused by hypothetical drought and ground-water withdrawals. Some of the greatest simulated declines were in well fields, operated by three municipalities that experienced water-supply problems during the 1980-81 drought.

Mixing and mingling in Iceland: The origin of a diverse suite of Tertiary lavas

NASA Astrophysics Data System (ADS)

Jordan, B. T.

2006-12-01

A sequence of intermediate and silicic volcanic units occurs within a stratigraphic package dominated by moderately evolved tholeiitic basalts in the mountains Laxardalsfjoll and Langadalsfjall in the southern Skagi Peninsula of north-central Iceland. This sequence consists of several minor rhyolite and dacite lavas directly overlain by a voluminous (>3 km3) litholigically diverse andesite to rhyolite lava flow Above this flow is a basaltic andesite to dacite lava, or lavas (mapping not complete), and the sequence is capped by an extensive rhyolite lava. Pyroclastic deposits, including one welded tuff, occur within the sequence. The sequence was erupted at 7.8 Ma, not long before the abandonment of the Skagi-Snaefellsnes rift zone in which it was erupted. The rhyolite lavas are generally aphyric. The lower rhyolites are of variable composition (71-75% SiO2) and the upper is a high-silica rhyolite (75-76% SiO2). The lower dacite and upper basaltic andesite to dacite lava(s) are aphyric and plot on a linear mixing trend between well defined end-members, a moderately evolved basalt and a high-silica rhyolite. The most anomalous unit is the andesite-rhyolite lava. It is lithologically heterogeneous with <<1% to 20% coarse (up to 3 cm) nearly equant plagioclase phenocrysts. Lithologies commonly vary across sharp borders within the flow, with domains of different lithologies being up to 10s of m in extent. The coarse plagioclase phenocrysts are calcic, up to An87 indicating an origin in basaltic magma. The whole rock composition varies from andesite (58% SiO2) to rhyolite (70% SiO2). Silica content is inversely correlated with phenocryst abundance, but can not be explained by phenocrysts alone. A wide range of mixing and mingling textures are observed at mesoscopic and microscopic scales. Major and trace element variations are quite distinct from the other mixed unit and indicate that the end members of mixing are a plagioclase-rich basalt and a range of silicic compositions from dacite to low-silica rhyolite. A candidate for the mafic end member of mixing is a plagioclase-ultraphyric basalt mapped in Vatnsdalsfjall (~10 km away). It has similar coarse equant plagioclase phenocrysts (up to 35%), with identical An-contents and distinctive patterns of inclusions. I propose that a dike that fed this lava also propagated at depth into a zoned dacite-rhyolite magma chamber, similar to the AD 1480 propagation of the Veidivotn fissure into the Torfajokull caldera. This triggered a large eruption from the zone of mingling/mixing, followed by a significant eruption from the evolved upper portion of the magma chamber. The diverse underlying small-volume rhyolites had been the normal products erupted from the zoned silicic magma chamber. The origin of the second, basaltic andesite to dacite, mixing trend is equivocal. The lavas constituting this trend occur immediately below and above the porphyritic lava suggesting that mixing between normal tholeiite and high-silica rhyolite magmas was ongoing in the upper part of the magma chamber at the time of the main eruption.

Quality of water from crystalline rock aquifers in New England, New Jersey, and New York, 1995-2007

USGS Publications Warehouse

Flanagan, Sarah M.; Ayotte, Joseph D.; Robinson, Gilpin R.

2012-06-25

Crystalline bedrock aquifers in New England and parts of New Jersey and New York (NECR aquifers) are a major source of drinking water. Because the quality of water in these aquifers is highly variable, the U.S. Geological Survey (USGS) statistically analyzed chemical data on samples of untreated groundwater collected from 117 domestic bedrock wells in New England, New York, and New Jersey, and from 4,775 public-supply bedrock wells in New England to characterize the quality of the groundwater. The domestic-well data were from samples collected by the USGS National Water-Quality Assessment (NAWQA) Program from 1995 through 2007. The public-supply-well data were from samples collected for the U.S. Environmental Protection Agency (USEPA) Safe Drinking Water Act (SDWA) Program from 1997 through 2007. Chemical data compiled from the domestic wells include pH, specific conductance, dissolved oxygen, alkalinity, and turbidity; 6 nitrogen and phosphorus compounds, 14 major ions, 23 trace elements, 222radon gas (radon), 48 pesticide compounds, and 82 volatile organic compounds (VOCs). Additional samples were collected from the domestic wells for the analysis of gross alpha- and gross beta-particle radioactivity, radium isotopes, chlorofluorocarbon isotopes, and the dissolved gases methane, carbon dioxide, nitrogen, and argon. Chemical data compiled from the public-supply wells include pH, specific conductance, nitrate, iron, manganese, sodium, chloride, fluoride, arsenic, uranium, radon, combined radium (226radium plus 228radium), gross alpha-particle radioactivity, and methyl tert-butyl ether (MtBE).Patterns in fluoride, arsenic, uranium, and radon distributions were discernable when the data were compared to lithology groupings of the bedrock, indicating that the type of bedrock has an effect on the quality of groundwater from NECR aquifers. Fluoride concentrations were significantly higher in groundwater samples from the alkali granite, peraluminous granite, and metaluminous granite lithology groups than from samples in the other lithology groups. Water samples from 1.4 percent of 2,167 studied wells had fluoride concentrations that were equal to or greater than the maximum contaminant level (MCL) of 4 milligrams per liter (mg/L) and 7.5 percent of the wells had fluoride concentrations that were equal to or greater than the secondary MCL of 2 mg/L. For arsenic, groundwater samples from the calcareous metasedimentary rocks in the New Hampshire-Maine geologic province, peraluminous granite, and pelitic rocks lithology groups had higher concentrations than did samples from the other lithology groups. Water samples from 13.3 percent of 2,054 studied wells had arsenic concentrations that were equal to or greater than the MCL of 10 micrograms per liter (μg/L), about double the national rate of occurrence in community-supply systems and in domestic wells of the United States. Uranium concentrations were significantly higher in groundwater samples from the peraluminous granite, alkali granite, and calcareous metasedimentary rocks in the New Hampshire-Maine geologic province lithology groups than from samples in the other lithology groups. Water samples from 14.2 percent of 556 studied wells had uranium concentrations equal to or greater than the MCL of 30 μg/L. Radon activities were equal to or greater than the proposed MCL of 300 picocuries per liter (pCi/L) in 95 percent of 943 studied wells, and 33 percent of the wells had radon activities were equal to or greater than the proposed alternative maximum contaminant level (AMCL) of 4,000 pCi/L. Radon activities exceeded the proposed AMCL in 20 percent or more of groundwater samples in each of the studied lithology groups with a minimum of 9 samples, but radon activities were significantly higher in groundwater samples from the alkali granite, peraluminous granite, and Narragansett basin metasedimentary rocks lithology groups. Water samples from 3.2 percent of 564 studied wells had combined radium activities equal to or greater than the MCL of 5 pCi/L; however, combined radium activities were not significantly different among the studied lithology groups.Land use and population density also were evaluated to explain patterns in water quality. Concentrations of nitrate, sodium, chloride, and MtBE from the studied wells were significantly greater in areas of high population density (≥50 persons per square kilometer) than in areas of low population density (<50 persons per square kilometer). Concentrations of sodium, chloride, and MtBE from the studied wells were significantly greater in areas classified as developed (urban lands) than in areas classified as undeveloped (forested), agricultural, or mixed (no dominant land use). Nitrate concentrations from the public-supply wells were not significantly different among the four land use categories, but nitrate concentrations from the domestic wells were significantly greater in areas classified as developed than in areas classified as undeveloped, agricultural, or mixed.Chloride to bromide mass ratios in the domestic well samples indicate that the groundwater was probably affected by at least three halogen sources: local precipitation and recharge waters, remnant seawater and connate waters evolved from seawater, and recharge waters affected by road salt. The groundwater in the NECR aquifers generally contained low concentrations of nitrate, VOCs, and pesticides. Less than 1 percent of water samples from 4,781 studied wells had concentrations of nitrate greater than the MCL of 10 mg/L. Less than 1 percent of water samples from 1,299 studied wells exceeded the USEPA advisory level of 20 to 40 μg/L for MtBE. None of the other studied VOCs exceeded a human health benchmark. MtBE (36 percent frequency detection) and chloroform (32.9 percent frequency detection) were the most frequently detected (>0.02 μg/L) VOCs in the domestic wells. MtBE was detected more often in water samples with apparent ages of less than 25 years than in water samples with apparent ages greater than 25 years. This finding is consistent with the time period of high MtBE use in areas in the United States where reformulated gasoline was mandated. The largest pesticide concentration was an estimated concentration of 0.06 μg/L for the herbicide metolachlor. Deethylatrazine, a degradate of atrazine, (18 percent frequency detection) and atrazine (8 percent frequency detection) were the only pesticide compounds detected (>0.001 μg/L) in more than 3 percent of the domestic wells. None of the detected pesticide compounds exceeded human health benchmarks.Concentrations of nitrate and gross alpha-particle activities were significantly greater in the water samples from the domestic wells than in samples from the public-supply wells. Concentrations of sodium, chloride, iron, manganese, and uranium were significantly greater in the water samples from the public-supply wells than in the samples from the domestic wells. One possible explanation may be related to differences in field processing (filtered samples from the domestic wells compared to unfiltered samples from the public-supply wells).The high frequency of detections for a wide variety of manmade and naturally occurring contaminants in both domestic and public-supply wells shows the vulnerability of NECR aquifers to contamination. The highly variable water quality and the association with highly variable lithology of crystalline bedrock underscores the importance of testing individual wells to determine if concentrations for the most commonly detected contaminants exceed human health benchmarks.

Near-surface structure of the Central Scandinavian Caledonides in northern Trøndelag, Norway, from correlation of seismic and MT profiles using gravity and magnetic data

NASA Astrophysics Data System (ADS)

Ebbing, J.; Goerigk, L.; Nasuti, A.; Roberts, D.; Korja, T. J.; Smirnov, M.

2014-12-01

The deep geology of northern Trøndelag is somewhat speculative as the Central Scandinavian Caledonides are intersected by the Møre-Trøndelag Fault Complex (MTFC) and only a few depth-penetrating geophysical profiles exist. Here, we correlate the mapped geological units and faults between a seismic-reflection profile and a MT profile. The seismic-reflection data were acquired in 5 segments over the period 1986-1990. The westernmost section of the seismic profile is dominated by a complex pattern of reflections and diffractions. This type of pattern is typical of polydeformed terranes with a mixture of contrasting felsic and mafic lithologies. The two steeply-dipping strands of the MTFC (Hitra-Snåsa and Verran faults) that transect the profile do not show any distinctive signature in the seismic data. The MT data were acquired in 2007 from the Swedish border to the Norwegian coast. The conductivity profile shows some distinct vertical changes as well as changes from the near-surface to shallow depths. The strands of the MTFC show especially a distinctive change in conductivity. The two profiles are almost parallel but separated by 100 km. To correlate the structures seen on both profiles, we have applied lineament analysis and 3D modelling of the gravity and magnetic field. The tilt derivative of the magnetic and isostatic gravity anomaly clearly allows us to identify and link the main geological boundaries between the profiles and to trace the strands of the MTFC from one profile to the other. This trend analysis indicates that at least the Verran Fault visibly modifies the pattern of seismic reflections. However, the main change in crustal lithology occurs farther to the west, almost at the coast where the Tarva Fault intersects the MT profile. This integrated analysis shows the benefit of combining gravity and magnetic interpretations with MT and seismic data to enable us to understand the near-surface geology and structure in more detail.

The stratigraphic utility of the trace fossil Pteridichnites biseriatus in the Upper Devonian of eastern West Virginia and western Virginia, USA

USGS Publications Warehouse

McDowell, R.R.; Avary, K.L.; Matchen, D.L.; Britton, J.Q.

2007-01-01

Similar lithologies and lithofacies are present in two Upper Devonian siliciclastic units, the Brallier and Foreknobs formations, in eastern West Virginia and western Virginia, USA. Specimens of an unusual trace fossil, Pteridichnites biseriatus, occur in variable numbers throughout both stratigraphic units. P. biseriatus is present in abundance in the lowermost Brallier and this abundance-zone serves as a local stratigraphic marker for the Brallier. The trace fossil, originally suggested as an indication of polychaete or arthropod locomotion, is herein proposed as the locomotion trace of an unidentified ophiuroid.

Aquifer susceptibility to perchlorate contamination in a highly urbanized environment

USGS Publications Warehouse

Woolfenden, Linda R.; Trefly, Michael G.

2007-01-01

Perchlorate contamination from anthropogenic sources has been released into the Rialto-Colton, California, USA, groundwater flow system since the 1940s during its production, distribution, storage, and use. Preliminary analysis of lithological, geophysical, and water-chemistry data provided new understanding of the pathways of perchlorate migration that aid in assessing the susceptibility of drinking-water supplies to contamination within the Rialto-Colton basin. Vertical migration of perchlorate into the main water-producing aquifers is restricted by an areally extensive old soil surface; however, perchlorate data indicate contamination below this soil surface. Possible pathways for the downward migration of the contaminated water include wellbore flow and discontinuities in the old soil surface. Horizontal migration of perchlorate is influenced by lithology and faults within the basin. The basin fill is a heterogeneous mixture of boulders, gravel, sand, silt, and clay, and internal faults may restrict perchlorate migration in some areas.

Remote sensing studies and morphotectonic investigations in an arid rift setting, Baja California, Mexico

NASA Astrophysics Data System (ADS)

El-Sobky, Hesham Farouk

The Gulf of California and its surrounding land areas provide a classic example of recently rifted continental lithosphere. The recent tectonic history of eastern Baja California has been dominated by oblique rifting that began at ˜12 Ma. Thus, extensional tectonics, bedrock lithology, long-term climatic changes, and evolving surface processes have controlled the tectono-geomorphological evolution of the eastern part of the peninsula since that time. In this study, digital elevation data from the Shuttle Radar Topography Mission (SRTM) from Baja California were corrected and enhanced by replacing artifacts with real values that were derived using a series of geostatistical techniques. The next step was to generate accurate thematic geologic maps with high resolution (15-m) for the entire eastern coast of Baja California. The main approach that we used to clearly represent all the lithological units in the investigated area was objectoriented classification based on fuzzy logic theory. The area of study was divided into twenty-two blocks; each was classified independently on the basis of its own defined membership function. Overall accuracies were 89.6%, indicating that this approach was highly recommended over the most conventional classification techniques. The third step of this study was to assess the factors that affected the geomorphologic development along the eastern side of Baja California, where thirty-four drainage basins were extracted from a 15-m-resolution absolute digital elevation model (DEM). Thirty morphometric parameters were extracted; these parameters were then reduced using principal component analysis (PCA). Cluster analysis classification defined four major groups of basins. We extracted stream length-gradient indices, which highlight the differential rock uplift that has occurred along fault escarpments bounding the basins. Also, steepness and concavity indices were extracted for bedrock channels within the thirty-four drainage basins. The results were highly correlated with stream length-gradient indices for each basin. Nine basins, exhibiting steepness index values greater than 0.07, indicated a strong tectonic signature and possible higher uplift rates in these basins. Further, our results indicated that drainage basins in the eastern rift province of Baja California could be classified according to the dominant geomorphologic controlling factors (i.e., fault-controlled, lithology-controlled, or hybrid basins).

Lithologies of the basement complex (Devonian and older) in the National Petroleum Reserve - Alaska

USGS Publications Warehouse

Dumoulin, Julie A.; Houseknecht, David W.

2001-01-01

Rocks of the basement complex (Devonian and older) were encountered in at least 30 exploratory wells in the northern part of the NPRA. Fine-grained, variably deformed sedimentary rocks deposited in a slope or basinal setting predominate and include varicolored (mainly red and green) argillite in the Simpson area, dark argillite and chert near Barrow, and widespread gray argillite. Chitinozoans of Middle-Late Ordovician and Silurian age occur in the dark argillite and chert unit. Sponge spicules and radiolarians establish a Phanerozoic age for the varicolored and gray argillite units, both of which contain local interbeds of chert-rich sandstone and silt-stone. Conglomerate and sandstone, also chert-rich but interbedded with mudstone and coal and of Early-Middle Devonian age, occur in the Topagoruk area; these strata formed in a fluvial environment. At East Teshekpuk, granite of probable Devonian age was penetrated. Brecciated, quartz-veined rock of uncertain protolith that may be part of the basement complex was encountered in the Ikpikpuk well. Seismic data indicate that angular unconformities truncate all sedimentary units of the basement complex in NPRA. Rocks correlative in age and lithofacies with the dark argillite and chert unit occur in the subsurface near Prudhoe Bay. Other argillite units in NPRA have similarities to basement rocks in the subsurface adjacent to ANWR and the Ordovician-Silurian Iviagik Group at Cape Lisburne, but lack the interbedded limestones found in the ANWR strata, and are less metamorphosed than, and compositionally distinct from, the Iviagik. The Topagoruk conglomerate and the East Teshekpuk granite resemble the Ulungarat formation and the Okpilak batholith, respectively, in the northeastern Brooks Range.

Mapping Post-Fire Vegetation Recovery at Different Lithologies of Taygetos mt (greece) with Multi-Temporal Remote Sensing Data

NASA Astrophysics Data System (ADS)

Vassilakis, Emmanuel; Mallinis, George; Christopoulou, Anastasia; Farangitakis, Georgios-Pavlos; Papanikolaou, Ioannis; Arianoutsou, Margarita

2017-04-01

Mt Taygetos (2407m), located at southern Peloponnese (Greece) suffered a large fire during the summer of 2007. The fire burned approximately 45% of the area covered by the endemic Greek fir (Abies cephalonica) and Black Pine (Pinus nigra) forest ecosystems. The aim of the current study is to examine the potential differences on post-fire vegetation recovery imposed by the lithology as well as the geomorphology of the given area over sites of the same climatic and landscape conditions (elevation, aspect, slope etc.). The main lithologies consist of carbonate, permeable, not easily erodible formations (limestones and marbles) and clastic, impermeable (schists, slate and flysch) erodible ones. A time-series of high spatial resolution satellite images were interpreted, analyzed and compared in order to detect changes in vegetation coverage which could prioritize areas of interest for fieldwork campaigns. The remote sensing datasets were acquired before (Ikonos-2), a few months after (Quickbird-2) and some years after (Worldview-3) the 2007 fire. High resolution Digital Elevation Model was used for the ortho-rectification and co-registration of the remote sensing data, but also for the extraction of the mountainous landscape characteristics. The multi-temporal image dataset was analyzed through GEographic-Object Based Image Analysis (GEOBIA). Objects corresponding to different vegetation types through time were identified through spectral and textural features. The classification results were combined with basic layers such as lithological outcrops, pre-fire vegetation, landscape morphology etc., supplementing a spatial geodatabase used for classifying burnt areas with varying post-fire plant community recovery. We validated the results of the classification during fieldwork and found that at a local scale, where the landscape features are quite similar, the bedrock type proves to be an important factor for vegetation recovery, as it clearly defines the soil generation along with its properties. Plant species recovery seems to be controlled by the local lithology as it was found weaker in plots overlying limestones and marbles, comparing to that observed over schists, even for the same species. In conclusion, post-fire vegetation recovery seems to be a complex process controlled not only from species biology, but also from the geological features.

Lithology, age and structure of early proterozoic greenstone belts, West African shield

NASA Technical Reports Server (NTRS)

Attoh, K.

1986-01-01

Lithologic and chemical data have been compiled for belts in the Proterozoic terrane. Available stratigraphic information from geologic maps of these areas indicate that a typical sequence is comprised of predominately mafic lava flows (basalt-andesite) at the base, which are overlain by felsic volcanic rocks including pyroclastic rocks and lavas. Lithostratigraphic data indicate the volcanic succession is 6-8 km thick. This is followed by 3-4 km of basaltic lava flows which are locally pillowed, the top of the unit is marked by a distinctive manganese formation (MF) consisting of Mn-Fe rich cherts up to 200 m thick. The youngest volcanic unit consists of mafic tuffs and breccia with a distinctive fragmental texture. Of about 100 chemical analyses reported calc-alkaline rocks constitute 55% and tholeiites 45%. Quartz-normative basalt constitutes 99% of the rock type in the tholeiitic suite. In the calc-alkaline suite, 9% of the analyses is basalt, 45% andesite and the rest is dacite and rhyodacite. The available data lead to the conclusion that the minimum age for the volcanic activity must be between 2200 and 2100 million years. It is significant that Archean ages have not been reported from any of the volcanic belts (1-10).

Mapping of lithologic and structural units using multispectral imagery. [Afar-Triangle/Ethiopia and adjacent areas (Ethiopian Plateau, Somali Plateau, and parts of Yemen and Saudi Arabia)

NASA Technical Reports Server (NTRS)

Kronberg, P. (Principal Investigator)

1974-01-01

The author has identified the following significant results. ERTS-1 MSS imagery covering the Afar-Triangle/Ethiopia and adjacent regions (Ethiopian Plateau, Somali Plateau, and parts of Yemen and Saudi Arabi) was applied to the mapping of lithologic and structural units of the test area at a scale 1:1,000,000. Results of the geological evaluation of the ERTS-1 imagery of the Afar have proven the usefullness of this type of satellite data for regional geological mapping. Evaluation of the ERTS images also resulted in new aspects of the structural setting and tectonic development of the Afar-Triangle, where three large rift systems, the oceanic rifts of the Red Sea and Gulf of Aden and the continental East African rift system, seem to meet each other. Surface structures mapped by ERTS do not indicate that the oceanic rift of the Gulf of Aden (Sheba Ridge) continues into the area of continental crust west of the Gulf of Tadjura. ERTS data show that the Wonji fault belt of the African rift system does not enter or cut through the central Afar. The Aysha-Horst is not a Horst but an autochthonous spur of the Somali Plateau.

Ash-flow tuffs of the Galiuro Volcanics in the northern Galiuro Mountains, Pinal County, Arizona

USGS Publications Warehouse

Krieger, Medora Louise Hooper

1979-01-01

The upper Oligocene and lower Miocene Galiuro Volcanics in the northern part of the Galiuro Mountains contains two distinctive major ash-flow tuff sheets, the Holy Joe and Aravaipa Members. These major ash-flows illustrate many features of ash-flow geology not generally exposed so completely. The Holy Joe Member, composed of a series of densely welded flows of quartz latite composition that make up a simple cooling unit. is a rare example of a cooling unit that has a vitrophyre at the top as well as at the base. The upper vitrophyre does not represent a cooling break. The Aravaipa Member. a rhyolite, is completely exposed in Aravaipa and other canyons and on Table Mountain. Remarkable exposures along Whitewash Canyon exhibit the complete change from a typical stacked-up interior zonation of an ash flow to a non welded distal margin. Vertical and horizontal changes in welding, crystallization, specific gravity, and lithology are exposed. The ash flow can be divided into six lithologic zones. The Holy Joe and Aravaipa Members of the Galiuro Volcanics are so well exposed and so clearly show characteristic features of ash-flow tuffs that they could be a valuable teaching aid and a source of theses for geology students.

An analysis of the lithology to resistivity relationships using airborne EM and boreholes

NASA Astrophysics Data System (ADS)

Barfod, Adrian A. S.; Christiansen, Anders V.; Møller, Ingelise

2014-05-01

We present a study of the relationship between dense airborne SkyTEM resistivity data and sparse lithological borehole data. Understanding the geological structures of the subsurface is of great importance to hydrogeological surveys. Large scale geological information can be gathered directly from boreholes or indirectly from large geophysical surveys. Borehole data provides detailed lithological information only at the position of the borehole and, due to the sparse nature of boreholes, they rarely provide sufficient information needed for high-accuracy groundwater models. Airborne geophysical data, on the other hand, provide dense spatial coverage, but are only indirectly bearing information on lithology through the resistivity models. Hitherherto, the integration of the geophysical data into geological and hydrogeological models has been often subjective, largely un-documented and painstakingly manual. This project presents a detailed study of the relationships between resistivity data and lithological borehole data. The purpose is to objectively describe the relationships between lithology and geophysical parameters and to document these relationships. This project has focused on utilizing preexisting datasets from the Danish national borehole database (JUPITER) and national geophysical database (GERDA). The study presented here is from the Norsminde catchment area (208 sq. km), situated in the municipality of Odder, Denmark. The Norsminde area contains a total of 758 boreholes and 106,770 SkyTEM soundings. The large amounts of data make the Norsminde area ideal for studying the relationship between geophysical data and lithological data. The subsurface is discretized into 20 cm horizontal sampling intervals from the highest elevation point to the depth of the deepest borehole. For each of these intervals a resistivity value is calculated at the position of the boreholes using a kriging formulation. The lithology data from the boreholes are then used to categorize the interpolated resistivity values according to lithology. The end result of this comparison is resistivity distributions for different lithology categories. The distributions provide detailed objective information of the resistivity properties of the subsurface and are a documentation of the resistivity imaging of the geological lithologies. We show that different lithologies are mapped at distinctively different resistivities but also that the geophysical inversion strategies influences the resulting distributions significantly.

Phosphate-Silicate Inclusions in Chaunskij: How Diverse are They?

NASA Astrophysics Data System (ADS)

Petaev, M. I.; Clarke, R. S., Jr.; Jarosewich, E.; Lipschutz, M. E.; Wang, M.-S.; Davis, A. M.; Steele, I. M.; Olsen, E. J.; Wood, J. A.

1993-07-01

The Chaunskij meteorite was found in 1985 and was recently classified as the most highly metamorphosed, shock-modified, and metal-rich mesosiderite [1]. It contains ~10 vol% mono- and polymineralic troilite-phosphate-silicate inclusions, micrometers to centimeters in size. Metal in Chaunskij displays a mesosiderite structure and is described in some detail in an accompanying paper [2]. Here we present new data on polymineralic inclusions that shed additional light on their origin. Two dominant silicate lithologies have been found in the inclusions. One, making up the largest inclusion (2.2 x 1.7 cm), consists of a fine-grained (20-30 micrometers) aggregate of anhedral pyroxene, subhedral plagioclase laths, and silica, with larger poikilitic grains of the first two minerals. Whitlockite is minor. Textures vary from microophitic to xenoblastic. This lithology, called "igneous," also contains rare primary clasts enriched in pyroxene, whose boundaries are almost unresolvable from the ground mass in transmitted light. The second, "metamorphic" lithology occurs as separate small inclusions and as larger areas in intimate contact with the "igneous" lithology in the largest inclusion. This lithology is a fine-grained (typically 30-50 micrometers) xenoblastic intergrowth of low-Ca pyroxene, whitlockite, and cordierite, with rare larger porphyritic grains of the first two minerals. Porphyritic pyroxene grain edges are generally irregular, indicative of reaction with the ground mass. Plagioclase is present only as a rare accessory mineral. Minor minerals in both lithologies are silica, kamacite, taenite, troilite, chromite, ilmenite, and rutile. Rare grains of pyrophanite, zircon, alabandite, stanfieldite, and a graftonite-farringtonite mineral are also present in the inclusions. Mineral compositions of small inclusions are more diverse than those characteristic of the "igneous" and "metamorphic" lithologies. Many of them consist of cordierite, pyroxene, and whitlockite intergrowths, with or without silica and opaque minerals. However, some inclusions do not match the mineralogies of "igneous" or "metamorphic" lithologies. They consist of cordierite only (inclusion #1-10); cordierite and silica (#1-18); silica, whitlockite, and troilite with minor Al-rich chromite and rare pyroxene (#4- 5A); plagioclase and whitlockite (#4-5D); and silica and whitlockite (#4-6E). Mineral compositions vary considerably both between and within all inclusions. No systematic differences between separate inclusions were found. Compositions of pyroxene and plagioclase match those of mesosideritic minerals. The chromite and ilmenite display systematic variations in MgO, MnO, Al(sub)2O(sub)3 and V(sub)2O(sub)3 contents, suggestive of a precursor material consisting of a series of basaltic rocks. The bulk chemical composition of the largest silicate inclusion, recalculated to the silicate fraction only, is very close to that of eucrites and mesosiderites except for a large enrichment in P and volatile chalcophiles. Major-element and REE chemistry and bulk mineralogy point to cumulate eucrites as the precursor of the silicate inclusions. This precursor was apparently slightly fractionated during the remelting event inferred by the structure of the "igneous" lithology. The "metamorphic" lithology apparently was formed due to reaction between silicates and phosphorus dissolved in the metal: Px + An + P + O --> Cord + Q + Whit. This reaction took place under ~700 degrees C and ~4 kbar [3] in the interior of the Chaunskij parent body. Compositions and textures of small inclusions suggest that the metamorphic reaction took place before the incorporation of the inclusions into the piece of metal making up the Chaunskij main mass. References: [1] Petaev M. I. et al. (1993) LPS XXIV, 1131-1132. [2] Clarke R. S. Jr. et al., this volume. [3] Petaev M. I. et al. (1992) Meteoritics, 27, 276-277.

Structural control on the emplacement of contemporaneous Sn-Ta-Nb mineralized LCT pegmatites and Sn bearing quartz veins: Insights from the Musha and Ntunga deposits of the Karagwe-Ankole Belt, Rwanda

NASA Astrophysics Data System (ADS)

Hulsbosch, Niels; Van Daele, Johanna; Reinders, Nathan; Dewaele, Stijn; Jacques, Dominique; Muchez, Philippe

2017-10-01

The Nb-Ta-Sn pegmatites and Sn quartz veins of the Rwamagana-Musha-Ntunga area in eastern Rwanda are part of the Mesoproterozoic Karagwe-Ankole Belt. These commodities are on a regional scale spatiotemporally associated to the early Neoproterozoic fertile G4-granite generation. Although a transition from the lithium-cesium-tantalum pegmatites to cassiterite-microcline-quartz veins has been observed in the Rwamagana-Musha-Ntunga area, the structural control and the paragenetic relationship between the mineralized pegmatites and the Sn bearing quartz veins is largely unknown. Consequently, this study investigates the occurrence of pegmatites and quartz veins and the structural and lithological controls on their emplacement. The metasediments in the area are affected by a regional compressional regime with a shortening direction oriented N70E, which resulted in a N20W-oriented fold sequence. The Lake Muhazi granite is present in center of the Karehe anticline. The structural orientations of pegmatites and quartz veins show that two important factors control their emplacement. The first control is the reactivation of pre-existing discontinuities such as the bedding, bedding-parallel joints or strike-slip fault planes. In view of the regional structural grain in the Rwamagana-Musha-Ntunga area, this corresponds with abundant N20W-oriented pegmatites and quartz veins. The reactivation is strongly related to the lithology of the host rocks. The Musha Formation, which mainly consists of decimeter- to meter-scale lithological alternations of metapelite, metasiltstone and metasandstone, represents the most suitable environment for bedding reactivation. This is reflected in the predominance of bedding-parallel pegmatites and quartz veins hosted by the Musha Formation. Strike-parallel joints were mainly observed in the competent lithologies. The second controlling factor is related to the regional post-compressional stress regime. New joints initiated upon emplacement of the pegmatites and quartz veins. The orientations of these joints are influenced by the regional stress regime and resulted in steep EW-oriented pegmatites and quartz veins in the Rwamagana-Musha-Ntunga area. The pegmatites and quartz veins are interpreted as being initiated upon emplacement under influence of the prevailing regional stress regime. This post-compressional stress regime is characterized by a subvertical maximum compressive stress.

Positive feedback between strain localization and fluid flow at the ductile-brittle transition leading to Pb-Zn-Fe-Cu-Ag ore deposits in Lavrion (Greece)

NASA Astrophysics Data System (ADS)

Scheffer, Christophe; Tarantola, Alexandre; Vanderhaeghe, Olivier

2016-04-01

At the crustal scale, the ductile-brittle transition (DBT) might correspond to a physical barrier that separates a deep reservoir of metamorphic and magmatic fluids from a shallow reservoir of surficial fluids. Rock rheology, and thus the location of the DBT, is mainly governed by lithology, temperature and the presence/absence of fluids. Accordingly, the position of the DBT potentially evolves during orogenic evolution owing to thermal evolution and fluid circulation. In turn rocks are transferred across it during burial and exhumation. These processes induce connections between fluid reservoirs which might play a role on ore deposition. In this contribution, we discuss the impact of lithological heterogeneities on deformation, fluid flow and ore deposition based on the example of the Lavrion low-angle top-to-the-SSW detachment accommodating gravitational collapse of the Hellenides orogenic belt in Greece. The Lavrion peninsula, localized along the western boundary of the Attic-Cycladic Metamorphic Core Complex, is characterized by Pb-Zn-Fe-Cu-Ag ore mineralization mainly concentrated along a lithological contact (marble/schists) below and within a detachment shear zone. The mylonitic marble below the detachment shear zone is composed of white layers of pure marble alternating with blue layers containing impurities (SiO2, Al2O3, organic matter…). Development of the mylonitic fabric in competent impure blue marble is associated with its preferred dolomitization related to focused fluid infiltration. This mylonitic marble is cross-cut by several cataclastic horizons preferentially developed within the more competent impure blue marble and newly-crystallized dolomitic horizon. These cataclasites are invaded by fluorite and calcite gangue minerals showing locally Mn, Pb, Zn, Fe oxides and/or hydroxides, sphalerite, Ag-galena, Ag-sulfur and native Ag. Oxygen and carbon stable isotopes performed on marble sections point out decarbonation with magmatic contribution and fluid-rock interactions including organic matter present in the whole-rock during ore precipitation. These features show the positive feedback between localization of ductile-brittle deformation-recrystallization, fluid circulation and ore deposition. Accordingly, during orogenic gravitational collapse, the activation of mylonitic-cataclastic low-angle detachments, controlled at first order by temperature, are, at second order, influenced by lithologic heterogeneities that are determinant at localizing fluid circulation, allowing thus a multi-localization of the DBT and ore deposition.

Late Neoproterozoic basement rocks of Meatiq area, Central Eastern Desert, Egypt: Petrography and remote sensing characterizations

NASA Astrophysics Data System (ADS)

Hassan, Safaa M.; El kazzaz, Yahiya A.; Taha, Maysa M. N.; Mohammad, Abdullah T.

2017-07-01

Meatiq dome is one of the mysteries of the basement rocks in Central Eastern Desert (CED) of Egypt. Its mode of formation, and tectonic evolution are still controversial and not fully understood. Satellite remote sensing is a powerful tool for geologic applications, especially in inaccessible regions of the Earth's surface. In this study, three proposed Landsat-8 band ratios (6/2, 6/7, (6/4*4/3)), (6/7, 6/4, 4/2), and (7/5, 7/6, 5/3) are successfully used for detailed geological mapping of the different lithological rock units exposed in Meatiq dome area in the CED. Landsat-8 Principal component (PC) images is also used for refinement the boundaries between the widely-exposed rock units in the study area. Fourteen spectral bands of Advanced Space borne Thermal Emission and Reflection Radiometer (ASTER) data are successfully used to emphasize the distribution of some rock forming minerals (i.e. muscovite, quartz, ferrous oxides, ferrous silicates and hydroxyl-bearing minerals) in the lithological rock units of Meatiq dome area. ASTER muscovite index (B7/B6) and quartz index (B14/B12), ferrous iron index (B5/B3), ferrous silicates index (B5/B4), mafic index (B12/B13) and hydroxyl-bearing minerals index ((B7/B6)*(B4/B6)) discriminate muscovite bearing rocks, Granitoids, and other felsic rocks, amphibolite and other mafic rocks. The proposed image processing methods effectively discriminates between four granitic varieties existed in Meatiq area. They are namely; Abu Ziran, Ariki, Fawakhir and Atalla Plutons. This study reveals that the applied data of ASTER and Landsat-8 enhanced images produced a modified geological map with well emphasized rock units which are verified with field observations, and petrographic study.

Late-Pleistocene evolution of the continental shelf of central Israel, a case study from Hadera

NASA Astrophysics Data System (ADS)

Shtienberg, Gilad; Dix, Justin; Waldmann, Nicolas; Makovsky, Yizhaq; Golan, Arik; Sivan, Dorit

2016-05-01

Sea-level fluctuations are a dominant mechanism that control coastal environmental changes through time. This is especially the case for the successive regressions and transgressions over the last interglacial cycle, which have shaped the deposition, preservation and erosion patterns of unconsolidated sediments currently submerged on continental shelves. The current study focuses on creating an integrated marine and terrestrial geophysical and litho-stratigraphic framework of the coastal zone of Hadera, north-central Israel. This research presents a case study, investigating the changing sedimentological units in the study area. Analysis suggest these represent various coastal environments and were deposited during times of lower than present sea level and during the later stages of the Holocene transgression. A multi-disciplinary approach was applied by compiling existing elevation raster grids, bathymetric charts, one hundred lithological borehole data-sets, and a 110 km-long sub-bottom geophysical survey. Based on seismic stratigraphic analysis, observed geometries, and reflective appearances, six bounding surfaces and seven seismic units were identified and characterized. These seismic units have been correlated with the available borehole data to produce a chronologically constrained lithostratigraphy for the area. This approach allowed us to propose a relationship between the lithological units and sea-level change and thus enable the reconstruction of Hadera coastal evolution over the last 100 ka. This reconstruction suggests that the stratigraphy is dominated by lowstand aeolian and fluvial terrestrial environments, subsequently transgressed during the Holocene. The results of this study provide a valuable framework for future national strategic shallow-water infrastructure construction and also for the possible locations of past human settlements in relation to coastal evolution through time.

A new locality of palygorskite-rich clay from the southeastern Yucatán: a potential material source for environmental applications

NASA Astrophysics Data System (ADS)

Krekeler, Mark P. S.; Kearns, Lance E.

2009-08-01

A palygorskite unit was discovered in a road cut of undifferentiated Tertiary limestone between the villages of El Pariso and San Roman (18°49.309N, 88°37.861W) in the southeastern Yucatán Peninsula, Mexico. This is the southern most locality of a clay-rich sedimentary unit reported in the literature for the Tertiary carbonates of the Yucatán Peninsula. This occurrence indicates a much wider range of palygorskite-rich clay deposition than previously recognized. The lithology is 99% clay and 1% sand to silt size diagenetic quartz grains. The clay consists of approximately 85% palygorskite, 15% montmorillonite and trace amounts of titanium oxides. EDS analyses on palygorskite are largely consistent with sedimentary palygorskites from other coastal marine settings, however palygorskite has a low total Fe content (average = 0.40 wt% expressed as Fe2O3) compared to many other sedimentary palygorskites. Montmorillonite chemical compositions are typical and compared to the palygorskite have substantially higher Fe2O3 concentrations (average = 3.90 wt%). The low percentage of coarse grains in the lithology combined with a high proportion of palygorskite and lack of detrimental trace minerals suggest the deposit is of industrial grade; however, it has limited reserves (6,000 m3). The unit could be potentially used in a wide array of environmental applications which are needed in the region including liners for landfills and constructed wetlands. The unit is in a geographic location which would serve the expanding economy of the region. This resource has the potential to have great impact on the quality of the local environment and the economy of a region under great environmental threat.

Sedimentology of the Upper Triassic-Lower Jurassic (?) Mosolotsane Formation (Karoo Supergroup), Kalahari Karoo Basin, Botswana

NASA Astrophysics Data System (ADS)

Bordy, Emese M.; Segwabe, Tebogo; Makuke, Bonno

2010-08-01

The Mosolotsane Formation (Lebung Group, Karoo Supergroup) in the Kalahari Karoo Basin of Botswana is a scantly exposed, terrestrial red bed succession which is lithologically correlated with the Late Triassic to Early Jurassic Molteno and Elliot Formations (Karoo Supergroup) in South Africa. New evidence derived from field observations and borehole data via sedimentary facies analysis allowed the assessment of the facies characteristics, distribution and thickness variation as well as palaeo-current directions and sediment composition, and resulted in the palaeo-environmental reconstruction of this poorly known unit. Our results show that the Mosolotsane Formation was deposited in a relatively low-sinuosity meandering river system that drained in a possibly semi-arid environment. Sandstone petrography revealed mainly quartz-rich arenites that were derived from a continental block provenance dominated by metamorphic and/or igneous rocks. Palaeo-flow measurements indicate reasonably strong, unidirectional current patterns with mean flow directions from southeast and east-southeast to northwest and west-northwest. Regional thickness and facies distributions as well as palaeo-drainage indicators suggest that the main depocenter of the Mosolotsane Formation was in the central part of the Kalahari Karoo Basin. Separated from this main depocenter by a west-northwest - east-southeast trending elevated area, an additional depocenter was situated in the north-northeast part of the basin and probably formed part of the Mid-Zambezi Karoo Basin. In addition, data also suggests that further northeast-southwest trending uplands probably existed in the northwest and east, the latter separating the main Kalahari Karoo depocenter from the Tuli Basin.

Integrating borehole logs and aquifer tests in aquifer characterization

USGS Publications Warehouse

Paillet, Frederick L.; Reese, R.S.

2000-01-01

Integration of lithologic logs, geophysical logs, and hydraulic tests is critical in characterizing heterogeneous aquifers. Typically only a limited number of aquifer tests can be performed, and these need to be designed to provide hydraulic properties for the principle aquifers in the system. This study describes the integration of logs and aquifer tests in the development of a hydrostratigraphic model for the surficial aquifer system in and around Big Cypress National Preserve in eastern Collier County, Florida. Borehole flowmeter tests provide qualitative permeability profiles in most of 26 boreholes drilled in the Study area. Flow logs indicate the depth of transmissive units, which are correlated across the study area. Comparison to published studies in adjacent areas indicates that the main limestone aquifer of the 000000Tamiami Formation in the study area corresponds with the gray limestone aquifer in western Dade County and the water table and lower Tamiami Aquifer in western Collier County. Four strategically located, multiwell aquifer tests are used to quantify the qualitative permeability profiles provided by the flowmeter log analysis. The hydrostratigraphic model based on these results defines the main aquifer in the central part of the study area as unconfined to semiconfined with a transmissivity as high as 30,000 m2/day. The aquifer decreases in transmissivity to less than 10,000 m2/day in some parts of western Collier County, and becomes confined to the east and northeast of the study area, where transmissivity decreases to below 5000 m2/day.Integration of lithologic logs, geophysical logs, and hydraulic tests is critical in characterizing heterogeneous aquifers. Typically only a limited number of aquifer tests can be performed, and these need to be designed to provide hydraulic properties for the principle aquifers in the system. This study describes the integration of logs and aquifer tests in the development of a hydrostratigraphic model for the surficial aquifer system in and around Big Cypress National Preserve in eastern Collier County, Florida. Borehole flowmeter tests provide qualitative permeability profiles in most of 26 boreholes drilled in the study area. Flow logs indicate the depth of transmissive units, which are correlated across the study area. Comparison to published studies in adjacent areas indicates that the main limestone aquifer of the Tamiami Formation in the study area corresponds with the gray limestone aquifer in western Dade County and the water table and lower Tamiami Aquifer in western Collier County. Four strategically located, multiwell aquifer tests are used to quantify the qualitative permeability profiles provided by the flowmeter log analysis. The hydrostratigraphic model based on these results defines the main aquifer in the central part of the study area as unconfined to semiconfined with a transmissivity as high as 30,000 m2/day. The aquifer decreases in transmissivity to less than 10,000 m2/day in some parts of western Collier County, and becomes confined to the east and northeast of the study area, where transmissivity decreases to below 5000 m2/day.

Geophysical expression of a buried niobium and rare earth element deposit: the Elk Creek carbonatite, Nebraska, USA

USGS Publications Warehouse

Drenth, Benjamin J.

2014-01-01

The lower Paleozoic Elk Creek carbonatite is a 6–8-km-diameter intrusive complex buried under 200 m of sedimentary rocks in southeastern Nebraska. It hosts the largest known niobium deposit in the U.S. and a rare earth element (REE) deposit. The carbonatite is composed of several lithologies, the relations of which are poorly understood. Niobium mineralization is most enriched within a magnetite beforsite (MB) unit, and REE oxides are most concentrated in a barite beforsite unit. The carbonatite intrudes Proterozoic country rocks. Efforts to explore the carbonatite have used geophysical data and drilling. A high-resolution airborne gravity gradient and magnetic survey was flown over the carbonatite in 2012. The carbonatite is associated with a roughly annular vertical gravity gradient high and a subdued central low and a central magnetic high surrounded by magnetic field values lower than those over the country rocks. Geophysical, borehole, and physical property data are combined for an interpretation of these signatures. The carbonatite is denser than the country rocks, explaining the gravity gradient high. Most carbonatite lithologies have weaker magnetic susceptibilities than those of the country rocks, explaining why the carbonatite does not produce a magnetic high at its margin. The primary source of the central magnetic high is interpreted to be mafic rocks that are strongly magnetized and are present in large volumes. MB is very dense (mean density 3200  kg/m3) and strongly magnetized (median 0.073 magnetic susceptibility), producing a gravity gradient high and contributing to the aeromagnetic high. Barite beforsite has physical properties similar to most of the carbonatite volume, making it a poor geophysical target. Geophysical anomalies indicate the presence of dense and strongly magnetized rocks at depths below existing boreholes, either a large volume of MB or another unknown lithology.

Preliminary lithogeochemical map showing near-surface rock types in the Chesapeake Bay watershed, Virginia and Maryland

USGS Publications Warehouse

Peper, John D.; McCartan, Lucy; Horton, J. Wright; Reddy, James E.

2001-01-01

This preliminary experimental lithogeochemical map shows the distribution of rock types in the Virginia and Maryland parts of the Chesapeake Bay watershed. The map was produced digitally by classifying geologic-map units according to composition, mineralogy, and texture; rather than by age and stratigraphic relationships as shown on traditional geologic maps. This map differs from most lithologic maps in that the lithogeochemical unit classification distinguishes those rock units having key water-reactive minerals that may induce acid neutralization, or reduction, of hosted water at the weathering interface. The validity of these rock units, however, is independent of water chemistry, because the rock units are derived from geologic maps and rock descriptions. Areas of high soil carbon content, and sulfide metal deposits are also shown. Water-reactive minerals and their weathering reactions yield five lithogeochemical unit classes: 1) carbonate rock and calcareous rocks and sediments, the most acid-neutralizing; 2)carbonaceous-sulfidic rocks and sediments, oxygen-depleting and reducing; 3) quartzofeldspathic rocks and siliciclastic sediments, relatively weakly reactive with water; 4) mafic silicate rocks/sediments, oxygen consuming and high solute-load delivering; and, 5) the rarer calcareous-sulfidic (carbonaceous) rocks, neutralizing and reducing. Earlier studies in some parts of the map area have related solute loads in ground and stream waters to some aspects of bedrock lithology. More recent preliminary tests of relationships between four of the classes of mapped lithogeochemical units and ground water chemistry, in the Mid-Atlantic area using this map, have focused on and verified the nitrate-reducing and acid-neutralizing properties of some bedrock and unconsolidated aquifer rock types. Sulfide mineral deposits and their mine-tailings effects on waters are beginning to be studied by others. Additional testing of relationships among the lithogeochemical units and aspects of ground and surface water chemistry could help to refine the lithogeochemical classification, and this map. The testing could also improve the usefulness of the map for assessing aquifer reactivity and the transport properties of reactive contaminants such as acid rain, and nitrate from agricultural sources, in the Chesapeake Bay watershed.

Magnetic Hysteresis of Deep-Sea Sediments in Korea Deep Ocean Study(KODOS) Area, NE Pacific

NASA Astrophysics Data System (ADS)

Kim, K.; Park, C.; Yoo, C.

2001-12-01

The KODOS area within the Clarion-Clipperton fracture zone (C-C zone) is surrounded by the Hawaiian and Line Island Ridges to the west and the central American continent to the east. Topography of the seafloor consists of flat-topped abyssal hills and adjacent abyssal troughs, both of which run parallel in N-S direction. Sediments from the study area consist mainly of biogenic sediments. Latitudinal zonation of sedimentary facies was caused by the accumulation of biogenic materials associated with the equatorial current system and movement of the Pacific plate toward the north or northwest. The KODOS area belongs to the latitudinal transition zone having depositional characteristics between non-fossiliferous pelagic clay-dominated zone and calcareous sediment-dominated zone. The box core sediments of the KODOS area are analyzed in an attempt to obtain magnetic hysteresis information and to elucidate the relationship between hysteresis property and lithological facies. Variations in magnetic hysteresis parameters with unit layers reflect the magnetic grain-size and concentrations within the sediments. The ratios of remanant coercivity/coercive force (Hcr/Hc) and saturation remnance/saturation magnetization (Mrs/Ms) indicate that coarse magnetic grains are mainly distributed in dark brown sediments (lower part of the sediment core samples) reflecting high Hcr/Hc and low Mrs/Ms ratios. These results are mainly caused by dissolution differences with core depth. From the plotting of the ratios of hyteresis parameters, it is indicated that magnetic minerals in cubic samples are in pseudo-single domain (PSD) state.

Petrophysical evaluation of the hydrocarbon potential of the Lower Cretaceous Kharita clastics, North Qarun oil field, Western Desert, Egypt

NASA Astrophysics Data System (ADS)

Teama, Mostafa A.; Nabawy, Bassem S.

2016-09-01

Based on the available well log data of six wells chosen in the North Qarun oil field in the Western Desert of Egypt, the petrophysical evaluation for the Lower Cretaceous Kharita Formation was accomplished. The lithology of Kharita Formation was analyzed using the neutron porosity-density and the neutron porosity-gamma ray crossplots as well as the litho-saturation plot. The petrophysical parameters, include shale volume, effective porosity, water saturation and hydrocarbon pore volume, were determined and traced laterally in the studied field through the iso-parametric maps. The lithology crossplots of the studied wells show that the sandstone is the main lithology of the Kharita Formation intercalated with some calcareous shale. The cutoff values of shale volume, porosity and water saturation for the productive hydrocarbon pay zones are defined to be 40%, 10% and 50%, respectively, which were determined, based on the applied crossplots approach and their limits. The iso-parametric contour maps for the average reservoir parameters; such as net-pay thickness, average porosity, shale volume, water saturation and the hydrocarbon pore volume were illustrated. From the present study, it is found that the Kharita Formation in the North Qarun oil field has promising reservoir characteristics, particularly in the northwestern part of the study area, which is considered as a prospective area for oil accumulation.

Synthrusting deposition of the Pennsylvanian and Permian Strathearn Formation, Northern Carlin Trend, Nevada

USGS Publications Warehouse

Theodore, T.G.; Berger, V.I.; Singer, D.A.; Harris, A.G.; Stevens, C.H.

2004-01-01

The middle Upper Pennsylvanian and middle Lower Permian Strathearn Formation belongs to the overlap assemblage of the Antler orogen in Nevada. At Beaver Peak, near the Carlin Trend of gold deposits, it contains synorogenic conglomerate deposits associated with emplacement of a regionally extensive, 1-km-thick tectonic wedge that is floored by the Coyote thrust. Normal marine conodont biofacies throughout the Strathearn Formation suggest middle shelf or deeper, depositional environments. The allochthon floored by the Coyote thrust has been thrust above a middle Upper Pennsylvanian, lower conglomerate unit of the Strathearn Formation. A middle Lower Permian upper conglomerate unit, the highest unit recognized in the Strathearn Formation, as well as similarly aged dolomitic siltstone, onlap directly onto Ordovician quartzarenite of the Vinini Formation that makes up most of the Coyote allochthon. Quartz grains and quartzarenite fragments of variable roundness and shape in the conglomerate units were derived from the presently adjoining tectonic lobe of mostly quartzarenite that advanced southeast (present geographic coordinates) during the late Paleozoic into the developing Strathearn basin. Chert fragments in the conglomerates probably were derived mostly from Devonian Slaven Chert, including a widespread thick me??lange unit of the Slaven Chert in the footwall of the Coyote thrust.Lithologic and shape ratio data from approximately 4200 clasts at 17 sites of the two major conglomerate units in the Strathearn Formation at Beaver Peak are roughly similar in that they contain only chert and quartzarenite clasts, and chert clasts predominate in both units. They differ in the relative proportion of the two lithologies whereby quartzarenite clasts increase sixfold in the upper unit (middle Lower Permian) versus its content in the lower conglomerate unit. Relations at the unconformity between the upper conglomerate unit and its underlying quartzarenite shows quartzarenite fragments actually breaking away from an immediately subjacent source. Ordovocian quartzarenite, which forms a tectonically uplifted wedge with the Coyote thrust at its base, became a source region for much of the quartzarenite detritus deposited preferentially in the upper parts of the Strathearn Formation. The conglomerate units of the Strathearn Formation temporally bracket emplacement of the Coyote thrust. Thrusting related to contractional reactivation of the Robert Mountains thrust system largely was completed by middle Early Permian. ?? 2004 Published by Elsevier B.V.

Unconventional Hydrocarbon Development Hazards Within the Central United States. Report 1: Overview and Potential Risk to Infrastructure

DTIC Science & Technology

2015-08-01

of the injection purpose, i.e., secondary oil and gas recovery, disposal of waste fluids, geothermal energy, and/or UHP hydraulic fracturing...activities such as reservoir impoundment, mining, wastewater injection, geothermal systems and CO2 capture have been linked directly to induced...activities, e.g., deep fluid injection, geothermal injection, and/or UHP wells, that critically affect deep lithologies and alter the existing mechanical

Geologic map of Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Hults, Chad P.; Mull, Charles G.; Karl, Susan M.

2015-12-31

This Alaska compilation is unique in that it is integrated with a rich database of information provided in the spatial datasets and standalone attribute databases. Within the spatial files every line and polygon is attributed to its original source; the references to these sources are contained in related tables, as well as in stand-alone tables. Additional attributes include typical lithology, geologic setting, and age range for the map units. Also included are tables of radiometric ages.

Petrographic and geochemical characteristics of a section through the Tiva Canyon Tuff at Antler Ridge, Yucca Mountain, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singer, F.R.; Widmann, B.L.; Dickerson, R.P.

1994-12-31

The Tiva Canyon Tuff of the Paintbrush Group of Miocene age caps much of Yucca Mountain, Nevada and is a compositionally zoned, compound cooling, pyroclastic flow that ranges from a dominantly high-silica rhyolitic base to a quartz-latitic caprock. Petrographic and geochemical studies have focused on rigorously defining the internal stratigraphy of this unit to support the detailed mapping of the Ghost Dance fault and other structures in the central fault block of Yucca Mountain. This study shows that devitrification textures and vapor phase mineralogy, in addition to other physical attributes such as pumice variability (flattening) and crystal content, can bemore » used as distinguishing criteria to better define lithologic zones within the Tiva Canyon Tuff. In addition, the study also shows that the petrographic textures and chemistry of the groundmass vary systematically within recognizable lithologic zones and may be used to characterize and vertically divide litho-stratigraphic zones within the Tiva Canyon Tuff.« less

Prospectivity Modeling of Karstic Groundwater Using a Sequential Exploration Approach in Tepal Area, Iran

NASA Astrophysics Data System (ADS)

Sharifi, Fereydoun; Arab-Amiri, Ali Reza; Kamkar-Rouhani, Abolghasem; Yousefi, Mahyar; Davoodabadi-Farahani, Meysam

2017-09-01

The purpose of this study is water prospectivity modeling (WPM) for recognizing karstic water-bearing zones by using analyses of geo-exploration data in Kal-Qorno valley, located in Tepal area, north of Iran. For this, a sequential exploration method applied on geo-evidential data to delineate target areas for further exploration. In this regard, two major exploration phases including regional and local scales were performed. In the first phase, indicator geological features, structures and lithological units, were used to model groundwater prospectivity as a regional scale. In this phase, for karstic WPM, fuzzy lithological and structural evidence layers were generated and combined using fuzzy operators. After generating target areas using WPM, in the second phase geophysical surveys including gravimetry and geoelectrical resistivity were carried out on the recognized high potential zones as a local scale exploration. Finally the results of geophysical analyses in the second phase were used to select suitable drilling locations to access and extract karstic groundwater in the study area.

A comparison of helicopter-borne electromagnetic systems for hydrogeologic studies

USGS Publications Warehouse

Bedrosian, Paul A.; Schamper, Cyril; Auken, Esben

2016-01-01

The increased application of airborne electromagnetic surveys to hydrogeological studies is driving a demand for data that can consistently be inverted for accurate subsurface resistivity structure from the near surface to depths of several hundred metres. We present an evaluation of three commercial airborne electromagnetic systems over two test blocks in western Nebraska, USA. The selected test blocks are representative of shallow and deep alluvial aquifer systems with low groundwater salinity and an electrically conductive base of aquifer. The aquifer units show significant lithologic heterogeneity and include both modern and ancient river systems. We compared the various data sets to one another and inverted resistivity models to borehole lithology and to ground geophysical models. We find distinct differences among the airborne electromagnetic systems as regards the spatial resolution of models, the depth of investigation, and the ability to recover near-surface resistivity variations. We further identify systematic biases in some data sets, which we attribute to incomplete or inexact calibration or compensation procedures.

HCMM imagery for the discrimination of rock types, the detection of geothermal energy sources and the assessment of soil moisture content in western Queensland and adjacent parts of New South Wales and South Australia

NASA Technical Reports Server (NTRS)

Cole, M. M. (Principal Investigator)

1980-01-01

The author has identified the following significant results. Day-visible and day-IR imagery of northwest Queensland show that large scale geological features like the Mitakoodi anticlinorium, which involves rocks of contrasting lithological type, can be delineated. North of Cloncurry, the contrasting lithological units of the Knapdale quartzite and bedded argillaceous limestones within the Proterozoic Corella sequence are clearly delineated in the area of the Dugald River Lode. Major structural features in the Mount Isa area are revealed on the day-visible cover. Which provides similar but less detailed information than the LANDSAT imagery. The day-IR cover provides less additional information for areas of outcropping bedrock than had been expected. Initial studies of the day-IR and night-IR cover for parts of South Australia suggest that they contain additional information on geology compared with day-visible cover.

Harmonic Analysis of Sedimentary Cyclic Sequences in Kansas, Midcontinent, USA

USGS Publications Warehouse

Merriam, D.F.; Robinson, J.E.

1997-01-01

Several stratigraphic sequences in the Upper Carboniferous (Pennsylvanian) in Kansas (Midcontinent, USA) were analyzed quantitatively for periodic repetitions. The sequences were coded by lithologic type into strings of datasets. The strings then were analyzed by an adaptation of a one-dimensional Fourier transform analysis and examined for evidence of periodicity. The method was tested using different states in coding to determine the robustness of the method and data. The most persistent response is in multiples of 8-10 ft (2.5-3.0 m) and probably is dependent on the depositional thickness of the original lithologic units. Other cyclicities occurred in multiples of the basic frequency of 8-10 with persistent ones at 22 and 30 feet (6.5-9.0 m) and large ones at 80 and 160 feet (25-50 m). These levels of thickness relate well to the basic cyclothem and megacyclothem as measured on outcrop. We propose that this approach is a suitable one for analyzing cyclic events in the stratigraphic record.

Compiling a national resistivity atlas of Denmark based on airborne and ground-based transient electromagnetic data

NASA Astrophysics Data System (ADS)

Barfod, Adrian A. S.; Møller, Ingelise; Christiansen, Anders V.

2016-11-01

We present a large-scale study of the petrophysical relationship of resistivities obtained from densely sampled ground-based and airborne transient electromagnetic surveys and lithological information from boreholes. The overriding aim of this study is to develop a framework for examining the resistivity-lithology relationship in a statistical manner and apply this framework to gain a better description of the large-scale resistivity structures of the subsurface. In Denmark very large and extensive datasets are available through the national geophysical and borehole databases, GERDA and JUPITER respectively. In a 10 by 10 km grid, these data are compiled into histograms of resistivity versus lithology. To do this, the geophysical data are interpolated to the position of the boreholes, which allows for a lithological categorization of the interpolated resistivity values, yielding different histograms for a set of desired lithological categories. By applying the proposed algorithm to all available boreholes and airborne and ground-based transient electromagnetic data we build nation-wide maps of the resistivity-lithology relationships in Denmark. The presented Resistivity Atlas reveals varying patterns in the large-scale resistivity-lithology relations, reflecting geological details such as available source material for tills. The resistivity maps also reveal a clear ambiguity in the resistivity values for different lithologies. The Resistivity Atlas is highly useful when geophysical data are to be used for geological or hydrological modeling.

Using seismic derived lithology parameters for hydrocarbon indication

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Riel, P.; Sisk, M.

1996-08-01

The last two decades have shown a strong increase in the use of seismic amplitude information for direct hydrocarbon indication. However, working with seismic amplitudes (and seismic attributes) has several drawbacks: tuning effects must be handled; quantitative analysis is difficult because seismic amplitudes are not directly related to lithology; and seismic amplitudes are reflection events, making it is unclear if amplitude changes relate to lithology variations above or below the interface. These drawbacks are overcome by working directly on seismic derived lithology data, lithology being a layer property rather than an interface property. Technology to extract lithology from seismic datamore » has made great strides, and a large range of methods are now available to users including: (1) Bandlimited acoustic impedance (AI) inversion; (2) Reconstruction of the low AI frequencies from seismic velocities, from spatial well log interpolation, and using constrained sparse spike inversion techniques; (3) Full bandwidth reconstruction of multiple lithology properties (porosity, sand fraction, density etc.,) in time and depth using inverse modeling. For these technologies to be fully leveraged, accessibility by end users is critical. All these technologies are available as interactive 2D and 3D workstation applications, integrated with seismic interpretation functionality. Using field data examples, we will demonstrate the impact of these different approaches on deriving lithology, and in particular show how accuracy and resolution is increased as more geologic and well information is added.« less

Magnetic Properties of the Chelyabinsk meteorite

NASA Astrophysics Data System (ADS)

Bezaeva, N. S.; Badyukov, D. D.; Nazarov, M. A.; Rochette, P.; Feinberg, J. M.

2013-12-01

The Chelyabinsk meteorite (the fall of February 15, 2013; Russia) is a LL5 ordinary chondrite. Numerous (thousands) stones fell as a shower to the south and the south-west of the city of Chelyabinsk. The stones consist of two intermixed lithologies, with the majority (2/3) being a light lithology with a typical chondritic texture and shock stage S4 (~30 GPa). The second lithology (1/3) is an impact melt breccia (IMB) consisting of blackened chondrite fragments embedded in a fine-grained matrix. We investigated the magnetic properties of the meteorite stones collected immediately after the fall by the expedition of the Vernadsky Institute, Moscow. The low-field magnetic susceptibility (χ0) of 174 fragments (135 chondritic and 39 IMB) weighing >3 g was measured. Each sample was measured three times in mutually perpendicular directions to average anisotropy. Also hysteresis loops (saturation magnetization Ms, coercivity Bc) and back-field remanence demagnetization curves (coercivity of remanence Bcr) in the temperature range from 10K to 700°C and other characteristics of some pieces (NRM, SIRM with their thermal and alternating field demagnetization spectra) were acquired. The mean logχ0 is 4.57×0.09 (s.d.) for the light lithology and 4.65×0.09 (s.d.) (×10-9 m3/kg) for the IMB, indicating that IMB is slightly richer in metal than the light chondritic lithology. According to [1], Chelyabinsk is three times more magnetic than the average LL5 fall, but similar to other metal-rich LL5 (e.g., Paragould, Aldsworth, Bawku, Richmond), as well as L/LL chondrites (e.g., Glanerbrug, Knyahinya, Qidong). The estimation of metal content from the Ms value gives 3.7 wt.% for the light fragments and 4.1 wt.% for IMB whereas the estimation from χ0 yields overestimated contents, e.g., 6.9 wt.% for the light lithology. Thermomagnetic curves Ms(T) up to 800°C identify the main magnetic carriers at room temperature (T0) and above as taenite and kamacite (no tetrataenite found), in accordance with mineralogical data. Additional magnetic analyses [2] confirm the absence of tetrataenite and show that metal grains are primarily multidomain and magnetically soft (Bc<2 mT and Bcr<23 mT) at T0. However, at temperatures <75 K, the magnetic remanence of the Chelyabinsk chondrite is dominated by high coercivity chromite with much higher Bcr (606 mT for the light lithology and 157 mT for IMB). These results are consistent with previously published data on ordinary chondrites [3]. Acknowledgments: This research was funded by a U.S. National Science Foundation IRM Visiting Fellowship. References: [1] Rochette P. et al. 2003. MAPS 38: 251-268. [2] Bezaeva N.S. et al. 2013. Geochem. Int. 51(7): 568-574. [3] Gattacceca J. et al. 2011. Geoph. Res. Lett. 38: L10203.

Diagenetic gypsum related to sulfur deposits in evaporites (Libros Gypsum, Miocene, NE Spain)

NASA Astrophysics Data System (ADS)

Ortí, Federico; Rosell, Laura; Anadón, Pere

2010-07-01

The Libros Gypsum is the thickest evaporite unit of the Miocene infill of the Teruel Basin in NE Spain. During the deposition of this unit, intense bacterial sulfate-reducing (BSR) activity in the lake depocenter generated a native sulfur deposit. Diagenetic gypsum resulted from subsequent sulfur oxidation. The different processes involved in these transformations were first investigated by Anadón et al. (1992). The present paper is concerned with this diagenetic gypsum from the stratigraphic, petrographic, isotopic and genetic points of view. Diagenetic gypsum occurs mainly as continuous or discontinuous layers, individual levels or lenses, irregular masses, nodules and micronodules, and veins. Its main textures are coarse-crystalline anhedral and fine-grained (alabastrine), both of which can replace any former lithology (carbonate, gypsum, and sulfur). The following sequence of processes and mineral/textural transformations is deduced: primary gypsum deposition — BSR and biodiagenetic carbonate/H 2S production — growth of native sulfur — growth of diagenetic gypsum — partial recrystallization of the diagenetic gypsum textures. The gypsification of the native sulfur generated two types of banded structures in the diagenetic gypsum: (1) concentric structures of centripetal growth, and (2) expansive, roughly concentric structures. In the first type, the gypsification operated from the outer boundaries towards the inner parts. In the second type, part of the carbonate hosting the sulfur was also gypsified (replaced/cemented). In the diagenetic gypsum, the δ34S values are in agreement with a native sulfur and H 2S provenance. The δ18O sulfate values, however, enable us to differentiate two main groups of values: one with positive values and the other with negative values. In the group of positive values, interstitial (evaporated) solutions participated in the sulfur oxidation; this process presumably occurred in a first oxidation stage during shallow-to-deeper burial of the Libros Gypsum unit. In the group of negative values, however, only meteoric waters participated in the oxidation, which presumably occurred in a second oxidation stage during the final exhumation of the unit. A third group of values is characterized by very high sulfur and oxygen values, suggesting that BSR residual solutions also participated in the oxidation processes locally. During the two oxidation stages, both the textural characteristics and the isotopic composition of the diagenetic gypsum indicate that gypsification operated as a multistadic process.

Isopach and structure contour maps of the Burro Canyon(?) Formation in the Chama-El Vado Area, Chama Basin, New Mexico

USGS Publications Warehouse

Ridgley, Jennie L.

1983-01-01

In the Chama Basin a wequence of conglomerate, sandstone, and red, gray-green, and pale-purple mudstone occurs stratigraphically between the Upper Jurassic Morrison Formation and Upper Cretaceous Dakota Sandstone. This stratigraphic interval has been called the Burro Canyon Formation by several workers (Craig and others, 1959; Smith and others, 1961; Saucier, 1974). Although similarities in lithology and stratigraphic position exist between this unit and the Burro Canyon Formation in Colorado, no direct correlation has been made between the two. For this reason the unit in the Chama Basin is called the Burro Canyon(?) Formation. 

Unified Ecoregions of Alaska: 2001

USGS Publications Warehouse

Nowacki, Gregory J.; Spencer, Page; Fleming, Michael; Brock, Terry; Jorgenson, Torre

2003-01-01

Major ecosystems have been mapped and described for the State of Alaska and nearby areas. Ecoregion units are based on newly available datasets and field experience of ecologists, biologists, geologists and regional experts. Recently derived datasets for Alaska included climate parameters, vegetation, surficial geology and topography. Additional datasets incorporated in the mapping process were lithology, soils, permafrost, hydrography, fire regime and glaciation. Thirty two units are mapped using a combination of the approaches of Bailey (hierarchial), and Omernick (integrated). The ecoregions are grouped into two higher levels using a 'tri-archy' based on climate parameters, vegetation response and disturbance processes. The ecoregions are described with text, photos and tables on the published map.

Estimation of Leakage Potential of Selected Sites in Interstate and Tri-State Canals Using Geostatistical Analysis of Selected Capacitively Coupled Resistivity Profiles, Western Nebraska, 2004

USGS Publications Warehouse

Vrabel, Joseph; Teeple, Andrew; Kress, Wade H.

2009-01-01

With increasing demands for reliable water supplies and availability estimates, groundwater flow models often are developed to enhance understanding of surface-water and groundwater systems. Specific hydraulic variables must be known or calibrated for the groundwater-flow model to accurately simulate current or future conditions. Surface geophysical surveys, along with selected test-hole information, can provide an integrated framework for quantifying hydrogeologic conditions within a defined area. In 2004, the U.S. Geological Survey, in cooperation with the North Platte Natural Resources District, performed a surface geophysical survey using a capacitively coupled resistivity technique to map the lithology within the top 8 meters of the near-surface for 110 kilometers of the Interstate and Tri-State Canals in western Nebraska and eastern Wyoming. Assuming that leakage between the surface-water and groundwater systems is affected primarily by the sediment directly underlying the canal bed, leakage potential was estimated from the simple vertical mean of inverse-model resistivity values for depth levels with geometrically increasing layer thickness with depth which resulted in mean-resistivity values biased towards the surface. This method generally produced reliable results, but an improved analysis method was needed to account for situations where confining units, composed of less permeable material, underlie units with greater permeability. In this report, prepared by the U.S. Geological Survey in cooperation with the North Platte Natural Resources District, the authors use geostatistical analysis to develop the minimum-unadjusted method to compute a relative leakage potential based on the minimum resistivity value in a vertical column of the resistivity model. The minimum-unadjusted method considers the effects of homogeneous confining units. The minimum-adjusted method also is developed to incorporate the effect of local lithologic heterogeneity on water transmission. Seven sites with differing geologic contexts were selected following review of the capacitively coupled resistivity data collected in 2004. A reevaluation of these sites using the mean, minimum-unadjusted, and minimum-adjusted methods was performed to compare the different approaches for estimating leakage potential. Five of the seven sites contained underlying confining units, for which the minimum-unadjusted and minimum-adjusted methods accounted for the confining-unit effect. Estimates of overall leakage potential were lower for the minimum-unadjusted and minimum-adjusted methods than those estimated by the mean method. For most sites, the local heterogeneity adjustment procedure of the minimum-adjusted method resulted in slightly larger overall leakage-potential estimates. In contrast to the mean method, the two minimum-based methods allowed the least permeable areas to control the overall vertical permeability of the subsurface. The minimum-adjusted method refined leakage-potential estimation by additionally including local lithologic heterogeneity effects.

Avoiding the Pitfalls of Anisotropy in Paleomagnetic Correlation of Snake River Plain Ignimbrites

NASA Astrophysics Data System (ADS)

Finn, D. R.; Coe, R. S.; Kelly, H.; Murphy, J.; Reichow, M. K.; Knott, T.; Branney, M.

2013-12-01

Migration of the Yellowstone hotspot center tracks northeast along the central Snake River Plain (cSRP), leaving a succession of calderas, bimodal rhyolitic and basaltic volcanism, and crustal deformation. Large-scale explosive volcanism common to this province between 12.5-8 Ma is characterized by unusually high-temperature, intensely welded, rheomorphic rhyolitic ignimbrites, typical of what is now known as ';Snake River (SR)-type volcanism'. Individual eruption volumes likely exceed 450 km3 but are poorly known due to the difficulty of correlating units between widely spaced (50-200 km) exposures along the north and south of the plain. Radiometric dating does not have the resolution to identify the eruptive units. Our goal is to use a combination of paleomagnetic, petrographic, chemical and field characterization to establish robust correlations and better constrain eruption volumes and frequencies. Paleomagnetic correlation using the stable remanence, which is the focus of this presentation, has the advantage of very high temporal resolution of the order of centuries. This is due to the geologically rapid rate of geomagnetic secular variation and high accuracy to which extrusive rocks may record the instantaneous direction of the magnetic field. We have collected more than 1200 paleomagnetic samples from over 90 sites to help build a regional stratigraphy between the dozens of known ignimbrite units in the cSRP. During this process, however, we have found that the use of paleomagnetism is complicated by the large variation in the paleomagnetic direction that sometimes exists both within and between sub-lithologies of the same flow. Individual SR-type ignimbrite cooling-units have an upper and lower glassy margin (vitrophyre) enclosing a lithoidal (microcrystalline) zone. These vitrophyre lithologies often have a shallow paleomagnetic direction compared to the lithoidal lithologies. Here we present preliminary results from a detailed paleomagnetic and rock magnetic study of one cooling unit and its thermal contact zone to better understand the source of discrepant directions. We found a relationship between anisotropy of thermal remanent magnetization (ATRM), coercivity, natural remanent magnetization intensity, and deflection of remanence direction. A strong lineation in the ATRM anisotropy suggests contemporaneous rheomorphic shear strain of the welding fabric during early stages of emplacement plays a key role in generating magnetic anisotropy. The low anisotropy of the lithoidal zone and its correlation with the magnetic direction of the underlying baked soil implies that crystallization somehow helps anneal this anisotropy prior to cooling below the unblocking temperature of the constituent magnetic minerals. We hypothesize that the glassy margins retain an anisotropic fabric related to emplacement which affects their ability to accurately record the magnetic field during cooling. The anisotropic fabric in the lithoidal zone is overprinted by continued grain growth and/or alteration and, therefore, more accurately records the paleomagnetic field direction.

Application of Landsat-8 and ALOS-2 data for structural and landslide hazard mapping in Kelantan, Malaysia

NASA Astrophysics Data System (ADS)

Beiranvand Pour, Amin; Hashim, Mazlan

2017-07-01

Identification of high potential risk and susceptible zones for natural hazards of geological origin is one of the most important applications of advanced remote sensing technology. Yearly, several landslides occur during heavy monsoon rainfall in Kelantan River basin, Peninsular Malaysia. Flooding and subsequent landslide occurrences generated significant damage to livestock, agricultural produce, homes and businesses in the Kelantan River basin. In this study, remote sensing data from the recently launched Landsat-8 and Phased Array type L-band Synthetic Aperture Radar-2 (PALSAR-2) on board the Advanced Land Observing Satellite-2 (ALOS-2) were used to map geologic structural and topographical features in the Kelantan River basin for identification of high potential risk and susceptible zones for landslides and flooding areas. The data were processed for a comprehensive analysis of major geological structures and detailed characterizations of lineaments, drainage patterns and lithology at both regional and district scales. The analytical hierarchy process (AHP) approach was used for landslide susceptibility mapping. Several factors such as slope, aspect, soil, lithology, normalized difference vegetation index (NDVI), land cover, distance to drainage, precipitation, distance to fault and distance to the road were extracted from remote sensing satellite data and fieldwork to apply the AHP approach. Directional convolution filters were applied to ALOS-2 data for identifying linear features in particular directions and edge enhancement in the spatial domain. Results indicate that lineament occurrence at regional scale was mainly linked to the N-S trending of the Bentong-Raub Suture Zone (BRSZ) in the west and Lebir Fault Zone in the east of the Kelantan state. The combination of different polarization channels produced image maps that contain important information related to water bodies, wetlands and lithological units. The N-S, NE-SW and NNE-SSW lineament trends and dendritic, sub-dendritic and rectangular drainage patterns were detected in the Kelantan River basin. The analysis of field investigation data indicates that many of flooded areas were associated with high potential risk zones for hydrogeological hazards such as wetlands, urban areas, floodplain scroll, meander bend, dendritic and sub-dendritic drainage patterns, which are located in flat topographic regions. Numerous landslide points were located in a rectangular drainage system that is associated with a topographic slope of metamorphic and quaternary rock units. Consequently, structural and topographical geology maps were produced for Kelantan River basin using PALSAR-2 data, which could be broadly applicable for landslide hazard mapping and identification of high potential risk zone for hydrogeological hazards. Geohazard mitigation programs could be conducted in the landslide recurrence regions and flooded areas to reduce natural catastrophes leading to loss of life and financial investments in the Kelantan River basin. In this investigation, Landsat-8 and ALOS-2 have proven to successfully provide advanced Earth observation satellite data for disaster monitoring in tropical environments.

Geomorphological response of a landscape to long-term tectonic and glacial processes: the upper Rhône basin, Central Swiss Alps

NASA Astrophysics Data System (ADS)

Stutenbecker, Laura; Schlunegger, Fritz

2015-04-01

The Rhône River in the Central Swiss Alps drains a 5380 km2 large basin that shows a high spatial variability of bedrock lithology, exhumation rate, glacial conditioning and climate. All of these factors were recently discussed to control erosion rates in orogenic settings in general, and particularly in the Alps (e.g. Wittmann et al. 2007, Vernon et al. 2008, Norton et al. 2010a). Thanks to various and densely distributed data, the upper Rhône basin located between the Aar massif and Lake Geneva is a suitable natural laboratory to analyze the landscape's geomorphological state and controlling factors at a basin-scale. In this study, we extract geomorphological parameters along the channels of ca. 50 tributary basins of various sizes that contribute to the sediment budget of the Rhône River either through sediment supply by torrents or debris flows. Their catchments are located in either granitic basement rocks (External Massifs), oceanic meta-sedimentary and ophiolitic rocks (Penninic nappes) or fine-grained continental-margin sediments (Helvetic nappes). The analysis of longitudinal river profiles from DEMs and slope/area relationships show that all tributary rivers within the Rhône basin are in topographic transient state that is expressed by mainly convex or concave-convex channel shapes with several knickpoints of either tectonic-lithological or glacial origin. Furthermore, the frequency distribution of elevations (hypsometry) along the river channel allows identifying glacially inherited morphologies and the recent erosional front. The combination of those different geomorphological data yields to a categorization of the tributary rivers into three endmember groups: (1) streams with highly convex profiles, testifying to a strong glacial inheritance, (2) concave-convex channels with several knickzones and inherited morphologies of past glaciations, (3) predominantly concave, relatively steep rivers with minor knickpoints and inner gorges. Assuming that increasing concavity is an expression of advancing topographic equilibration (Wobus et al. 2006, and others), tributaries within the Rhône basin are in different states of equilibrium. Interestingly, the three groups correspond with distinct litho-tectonic units: Tributaries of group 1 are frequently found in the External Massifs, whereas channels of group 2 and 3 are located in the Penninic and Helvetic nappes, respectively. Fission-track data from the Alps (Vernon et al. 2008) also suggest a spatially variable exhumation history closely related to the different litho-tectonic units, ranging from youngest exhumation in the External Massifs, intermediate in the Helvetic units and oldest in the Penninic units. Non-equilibrated river profiles in the External Massifs can be explained by a combination of recent glaciation and exhumation. In contrast, river profiles in the Helvetic nappes appear to be closer to topographic steady state. Rivers located in the Penninic nappes, which show much older exhumation ages, were probably perturbed mainly by multiple glaciations and have not equilibrated yet. These observations suggest that differences in response times of river channels are probably conditioned by the differences in lithologies and tectonic histories of the three litho-tectonic domains. Norton, K.P., Abbühl, L.M. and Schlunegger, F., 2010a, Glacial conditioning as an erosional driving force in the Central Alps: Geology, v.38, p. 655-658 Vernon, A.J., van der Beek, P.A., Sinclair, H.D., Rahn, M.K., 2008, Increase in late Neogene denudation of the European Alps confirmed by analysis of a fission-track thermochronology database. EPSL, v. 270, p. 316-329. Wittmann, H., von Blanckenburg, F., Kruesmann, T., Norton, K.P., and Kubik, P.W., 2007, Relation between rock uplift and denudation from cosmogenic nuclides in river sediment in the Central Alps of Switzerland: J. Geophys. Res., v. 112, p. F04010 Wobus, C., Whipple, K.X, Kirby, E., Snyder, E., Johnson, J., Spyropolou, K., Crosby, B., and Sheehan, D., 2006, Tectonics from topography: Procedures, promise, and pitfalls, in Willett, S.D. et al., eds., Tectonics, climate, and landscape evolution: GSA Spec. Paper 398, p. 55-74

Origin of marls from the Polish Outer Carpathians: lithological and sedimentological aspects

NASA Astrophysics Data System (ADS)

Górniak, Katarzyna

2012-10-01

Outcrops of marls, occurring within the sandstone-shaly flysch deposits of the Polish part of Outer Carpathians, considered to be locus typicus of these rocks, were described, measured and sampled. Lithologic features of marls, representing 15 complexes of different age and occurring in 15 complexes of various tectonic units, are presented (Fig. 1, 2). The present studies were concerning Jurassic marls from the Silesian Unit (Goleszów Marls), Upper Cretaceous marls from the Skole and Sub-Silesian Units (Siliceous-Fucoid and Węgierka Marls and Węglowka, Frydek, Jasienica and Zegocina Marls respectively), and Eocene-Oligocene marls from the Magura, Fore-Magura and Skole Units (Łącko, Zembrzyce, Budzów, Leluchów and Niwa, as well as Grybów and Sub-Cergowa and Dynów Marls respectively). The former opinions on lithology, age, formal subdivision, sedimentation conditions and genesis of these rocks are discussed (Table 1, 2; Fig. 1). Detailed description of the above mentioned marl-bearing complexes are presented and for each of them the typical lithological features are determined (Tables 3 - 20). The results of profiling are presented against the background of geological studies of the Carpathian marls. The results of lithologic studies are compared to form a classification scheme and are used as the basis of distinguishing genetic types of marls. Moreover, the interpretation of the conditions of sedimentation of these rocks is presented. According to the present author’s studies, in the outcrops of marls considered to be locus typicus of the above mentioned rocks, there are both monolithic and polylithic complexes exposed. The polylithic complexes contain apart from marls intercalations of arenaceous-shaly flysch (Table 19). Event sedimentation of marly facies, appearing at different times and in various parts of the Carpathian basin is the result of periodically repeating conditions favouring the sedimentation of marls. Carpathian marls seem to be lithologically diversified. This is a natural for these rocks, uniting in variable proportions the features of limestones, clays, siliceous and clastic rocks. Depending on the proportions of these components, they display the features of the dominant one. The lithologies of Carpathian marls do not depend on their age and position in the sedimentation basin. Nevertheless, apart from visible differentiation of marls they show many common lithologic features: fine grain size, in general corresponding to silty-clayey fraction, variable but usually considerable thickness of beds of nonarenaceous variety of marls (0.5 - 1000 cm) and small thickness of arenaceous one (2 - 62 cm). In the majority of marly complexes, the arenaceous variety, starved ripplemarks, thin sandstone beds and sandy lamines occur in bottom parts of marly beds. The majority of marls display variably developed lamination and the occurrence of burrows (Table 19). Taking into account the Ghibaudo’s (1992) classification it was estimated that the marls in question can be assigned to three finest grained lithofacies: M (mud beds), MT (mud-silty couplets) and MS (mud-sand couplets) as well as to the MyG facies (muddy gravel). These lithofacies appear in marly complexes in various proportions (Table 20). Internal structures of beds are evidence of settling grains from suspension (depositional interval e2), interrupted with different intensity by deposition from traction (depositional intervals b, d and e1), and reworking of sediments by weak bottom currents (depositional intervals c and c0). The occurrence of similar lithologic features in marls of different age that come from different tectonic units is evidence of the repeating of similar sedimentation conditions, favouring the development of marly facies, at different times and in different parts of sedimentation basin of the Outer Carpathians. According to the present author’s analysis, there is a distinct relationship between the appearance of marls and tectonic evolution of the Outer Carpathian basin. Marls initiate sedimentation, indicate reconstruction stages and are closing the deposition in the Outer Carpathian basin (Fig. 1). Marls appear in the Polish part of Outer Carpathians in Upper Jurassic, initiating sedimentation in the northern Tethyan domain. Subsequently, they occur within Upper Cretaceous sandy-shaly flysch, indicating the reconstitution stage of Outer Carpathian basin and from Eocene to Oligocene are completing the deposition in successively closing basins (Fig. 1). The appearance of marls indicates the stages of tectonic evolution of the Outer Carpathians. The opening and reconstitution of a basin is accompanied by appearance of marls distinguished as preorogenic (Goleszów, Siliceous-Fucoid, Węgierka. Frydek and Żegocina Marls), their closing - synorogenic marls (Lącko, Budzów, Zembrzyce, Leluchów, Niwa, Grybów, Sub-Cergowa and Dynów Marls). Marls represent sediments redeposited from shelves to deeper parts of basins in the form of muds (M, MT and MS facies) and as olistostromes and olistoliths (MyG facies) (Tables 19, 20). Marls redeposited in the form of olistoliths appear in the stage of opening of the Outer Carpathian basin on the boundary of the Jurassic/Cretaceous period (Goleszow Marls) and in the stage of its Upper Cretaceous reconstitution (Baculite and Zegocina? Marls). In the complexes containing redeposited marls in the form of muds, submarine slumps occur (Table 19). These features indicate tectonic disquiet accompanying deposition of marls. Among the marls studied, dark coloured rocks appear (black, bluish-gray, greenish-gray) and olive and light- coloured (creamy, beige), as well as variegated and red (Table 19). The differentiation of colours indicates sedimentation of Carpathian marls both in oxygenated environments and those that are oxygen-depleted. The analysis of evolution of the Carpathian basins indicates that they were starved basins during sedimentation of marls. Limited supply of clastic material in such basins suggests the discussion on the source of the clay minerals - one of essential components of marls. The occurrence of pyroclastic strata in sediments of the same age (Fig. 1) suggests their origin to be related to volcanic material. The data of other authors, and the detailed profiling by the present author of outcrops that are considered to be locus typicus of marls and the appearance of which indicates a distinct correlation to tectonics of the Outer Carpathians, allowed to the present author to systematize and broaden the geological knowledge concerning the evolution of the marly facies in the northern part of the Tethyan Ocean. The conditions of sedimentation of marls deduced from the analysis of evolution of sedimentation basin of the Outer Carpathians and from lithologic data can be summarized as follows: - marls appear episodically in the Outer-Carpathian basin (mono- and polylithic complexes) and determine the stages of its tectonic evolution; they initiate the stages of opening and indicate the reconstitution of basins (preorogenic marls) and closing sedimentation cycle (synorogenic marls); - marls were deposited under conditions of tectonic disquiet (the presence of MyG facies), accompanied by volcanic activity (occurrence if pyroclastic rocks within chronostratigraphic equivalents of the marls studied); - marly deposits were formed both under oxidizing and oxygen-depleted conditions, i.e. when the availability of oxygen in the bottom sediments was limited (variable colouration); - marls represent the deposits of debris flows (MyG facies) redeposited from shelves in lithified form into zones that are situated close to the basin margins (olistoliths) and as resuspensed shelf muds accumulating within basinal sediments in the seafloor depressions (trap sediments) by suspension settling mechanism and periodically reworked by currents (M, MT, and MS facies).

Geologic aspects of the surficial aquifer in the upper East Coast planning area, Southeast Florida

USGS Publications Warehouse

Miller, Wesley L.

1980-01-01

The Upper East Coast Planning Area, as designated by the South Florida Water Management District, consists of St. Lucie County, Martin County, and eastern Okeechobee County. The surficial aquifer is the main source of freshwater for agricultural and urban uses in the area. The geologic framework of the aquifer is displayed by contour mapping and lithologic cross sections to provide water managers with a better understanding of the natural restraints that may be imposed on future development. The surficial aquifer is primarily sand, limestone, shell, silt, and clay deposited during the Pleistocene and Pliocene Epochs. The aquifer is unconfined and under water-table conditions in most of the area, but locally, artesian conditions exits where discontinuous clay layers act as confining units. Impermeable and semipermeable clays and marls of the Tamiami (lower Pliocene) and Hawthorn Formations (Miocene) unconformably underlie the surficial aquifer and form its base. Contour lines showing the altitude of the base of the aquifer indicate extensive erosion of the Miocene sediments prior to deposition of the aquifer materials. (USGS)

Mg-Spinel-rich lithology at crater Endymion in the lunar nearside

NASA Astrophysics Data System (ADS)

Bhattacharya, Satadru; Chauhan, Prakash; Ajai, A.

2012-07-01

The recent discovery of a Mg-Spinel-rich lithology at the inner ring of Mare Moscoviense (a farside mare) by [1, 2] based on the analysis of high-resolution Moon Mineralogy Mapper (M3) data from Chandrayaan-1, has stimulated interest in studying and identifying more and more such rock types across the lunar surface as spinel-rich lithologies and OOS (Orthopyroxene-Olivine-Spinel) suites of rocks hold the key to understand the deeper crustal composition and processes of the Moon. The genesis of this spinel-rich rare and unusual lithology on the lunar surface is yet to be understood by the lunar scientists. [3-6] has reported the occurrence of Mg-Spinel-rich lithology at the central peaks of crater Theophilus. The Mg-spinel-rich lithology at Theophilus is found to occur in association with mafic-free plagioclase and associated with lesser exposures of pyroxene and olivine-bearing materials. In a very recent work, [7] has identified Mg-spinel rich lithology at the floor of crater Copernicus. Very recently [8] has reported presence of Mg-spinel-rich lithology at the central peak of crater Tycho in association with olivine, crystalline plagioclase and high-Ca pyroxenes. All these detections are restricted within very small areal extents. Here, we report a new identification of this Mg-spinel-rich lithology at the rim of crater Endymion situated near the northeast limb of the Moon at the nearside using high-resolution M3 data. In Endymion, Mg-spinel-rich lithology occurs in close association with orthopyroxene-olivine assemblages and therefore represent OOS lithological suite of rocks. Spectral signature of Mg-spinel-rich lithology at the rim of crater Endymion: Spectra of Mg-spinel lacks 1000-nm absorption feature and is characterised by a strong absorption near 2000 nm arising due to the small amounts of Fe2+ in the tetrahedral crystallographic site of the mineral. Spectral signature of Mg-spinel-rich lithology, as obtained from the southern rim of crater Endymion, shows this distinct diagnostic absorption feature. It occurs in close association with orthopyroxene and orthopyroxene-olivine-rich lithologies. Olivine mostly occurs as a mixture with orthopyroxene and/or spinel as olivine spectra shows a prominent absorption near 2000 nm which is typical of pyroxene and/or spinel. Exposure sizes of Mg-spinel-rich lithology are very small and comprises of maximum 5-10 M3 pixels. Geological Setting: Endymion is a 125-km diameter crater situated near the northeast limb of the Moon and is characterised by concentric faluted rim structure. It is located to the east of Mare Frigoris and north of Lacus Temporis. The crater floor has been flooded by low-albedo basaltic lava. The floor appears smooth and featureless having very few tiny craterlets located within the rim. A string of three secondary craters lie near the northwestern inner wall. Mg-Spinel-rich lithology is mostly concentrated along the southern rim of crater Endymion and mosty occur along the flanks of faluted rims. Integrated Band Depth (IBD) images have been generated to analyse the relative strength of the absorption features near 1000 nm and 2000 nm respectively. In the IBD-2000 image, Mg-spinel-rich lithology appears as a bright spot in an otherwise dark surrounding. Implications for the occurrence of Mg-spinel-rich lithology: The occurrences of Mg-spinel-rich lithology at the southern rim of crater Endymion in close association with orthopyroxenes and orthopyroxene-olivine mixtures has a similarity with that of the OOS lithology reported from the Mare Moscoviense in terms of their geological settings. This kind of geological setting hint towards the deep seated origin for this Mg-spinel-rich lithology as the faulted rims of the impact basins associated with large hypervelocity impacts are believed to have excavated materials from great depths. References. [1] Pieters, C.M. et al. (2010) LPSC XXXXI, #1854. [2] Pieters, C.M. et al. (2011) JGR, 116, E00G08. [3] Lal, D. et al. (2011) LPSC XXXXII, #1339. [4] Dhingra, D. et al. (2011) LPSC XXXXII, #2388. [5]. Dhingra, D. et al. (2011) GRL, 38, L11201. [6] Lal, D. et al. (2012) Accepted in Jour. Earth System Science, January, 2012. [7] Dhingra, D. and Pieters, C.M. (2011) Annual meeting of Lunar Exploration Analysis Group (LEAG), #2024. [8] Kaur, P. et al. (2012) LPSC XXXXIII, #1434. }

Lithological and textural controls on radar and diurnal thermal signatures of weathered volcanic deposits, Lunar Crater region, Nevada

NASA Technical Reports Server (NTRS)

Plaut, Jeffrey J.; Rivard, Benoit

1992-01-01

Radar backscatter intensity as measured by calibrated synthetic aperture radar (SAR) systems is primarily controlled by three factors: local incidence angle, wavelength-scale roughness, and dielectric permittivity of surface materials. Radar observations may be of limited use for geological investigations of surface composition, unless the relationships between lithology and the above characteristics can be adequately understood. In arid terrains, such as the Southwest U.S., weathering signatures (e.g. soil development, fracturing, debris grain size and shape, and hill slope characteristics) are controlled to some extent by lithologic characteristics of the parent bedrock. These textural features of outcrops and their associated debris will affect radar backscatter to varying degrees, and the multiple-wavelength capability of the JPL Airborne SAR (AIRSAR) system allows sampling of textures at three distinct scales. Diurnal temperature excursions of geologic surfaces are controlled primarily by the thermal inertia of surface materials, which is a measure of the resistance of a material to a change in temperature. Other influences include albedo, surface slopes affecting insolation, local meteorological conditions and surface emissivity at the relevant thermal wavelengths. To first order, thermal inertia variations on arid terrain surfaces result from grain size distribution and porosity differences, at scales ranging from micrometers to tens of meters. Diurnal thermal emission observations, such as those made by the JPL Thermal Infrared Multispectral Scanner (TIMS) airborne instrument, are thus influenced by geometric surface characteristics at scales comparable to those controlling radar backscatter. A preliminary report on a project involving a combination of field, laboratory and remote sensing observations of weathered felsic-to basaltic volcanic rock units exposed in the southern part of the Lunar Crater Volcanic Field, in the Pancake Range of central Nevada is presented. Focus is on the relationship of radar backscatter cross sections at multiple wavelengths, apparent diurnal temperature excursions identified in multi-temporal TIMS images, surface geometries related to weathering style, and parent bedrock lithology.

The discovery and geophysical response of the Atlántida Cu-Au porphyry deposit, Chile

NASA Astrophysics Data System (ADS)

Hope, Matthew; Andersson, Steve

2016-03-01

The discovery of the Atlántida Cu-Au-Mo porphyry deposit, which is unconformably overlain by 25-80 m of gravels, is a recent example of exploration success under cover in a traditional mining jurisdiction. Early acquisition of geophysics was a key tool in the discovery, and in later guiding further exploration drilling throughout the life of the project. Detailed review of the geophysical response of the deposit, with respect to the distribution of lithologies and alteration, coupled with their petrophysical properties has allowed full characterisation, despite no exposure at the surface of host rock nor porphyry-style mineralisation. Data acquired over the project include induced polarisation, magnetotellurics, ground and airborne magnetics, ground-based gravimetry, and petrophysical sampling. The distribution of the key geological features of the deposit has been inferred via acquisition of petrophysical properties and interpretation of surface geophysical datasets. Magnetic susceptibility is influenced strongly by both alteration and primary lithology, whilst density variations are dominated by primary lithological control. Several studies have shown that electrical properties may map the footprint of the hydrothermal system and associated mineralisation, via a combination of chargeability and resistivity. These properties are observed in geophysical datasets acquired at surface and allow further targeting and sterilisation at the deposit and project scale. By understanding these geophysical characteristics in a geological context, these data can be used to infer distribution of lithological units, depth to exploration targets and the potential for high grade mineralisation. Future exploration will likely be increasingly reliant on the understanding of the surface manifestations of buried deposits in remotely acquired data. This review summarises the application and results of these principles at the Atlántida project of northern Chile. Geophysical data can be used to improve the chances of discovery beneath post-mineral cover, and also improve drilling results throughout the advanced exploration of the program. The process of data review against geological control information is essential.

Discrimination of iron ore deposits of granulite terrain of Southern Peninsular India using ASTER data

NASA Astrophysics Data System (ADS)

Rajendran, Sankaran; Thirunavukkarasu, A.; Balamurugan, G.; Shankar, K.

2011-04-01

This work describes a new image processing technique for discriminating iron ores (magnetite quartzite deposits) and associated lithology in high-grade granulite region of Salem, Southern Peninsular India using visible, near-infrared and short wave infrared reflectance data of Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER). Image spectra show that the magnetite quartzite and associated lithology of garnetiferrous pyroxene granulite, hornblende biotite gneiss, amphibolite, dunite, and pegmatite have absorption features around spectral bands 1, 3, 5, and 7. ASTER band ratios ((1 + 3)/2, (3 + 5)/4, (5 + 7)/6) in RGB are constructed by summing the bands representing the shoulders of absorption features as a numerator, and the band located nearest the absorption feature as a denominator to map iron ores and band ratios ((2 + 4)/3, (5 + 7)/6, (7 + 9)/8) in RGB for associated lithology. The results show that ASTER band ratios ((1 + 3)/2, (3 + 5)/4, (5 + 7)/6) in a Red-Green-Blue (RGB) color combination identifies the iron ores much better than previously published ASTER band ratios analysis. A Principal Component Analysis (PCA) is applied to reduce redundant information in highly correlated bands. PCA (3, 2, and 1 for iron ores and 5, 4, 2 for granulite rock) in RGB enabled the discrimination between the iron ores and garnetiferrous pyroxene granulite rock. Thus, this image processing technique is very much suitable for discriminating the different types of rocks of granulite region. As outcome of the present work, the geology map of Salem region is provided based on the interpretation of ASTER image results and field verification work. It is recommended that the proposed methods have great potential for mapping of iron ores and associated lithology of granulite region with similar rock units of granulite regions of Southern Peninsular India. This work also demonstrates the ability of ASTER's to provide information on iron ores, which is valuable for mineral prospecting and exploration activities.

Lithologic Controls on Structure Highlight the Role of Fluids in Failure of a Franciscan Complex Accretionary Prism Thrust Fault

NASA Astrophysics Data System (ADS)

Bartram, H.; Tobin, H. J.; Goodwin, L. B.

2015-12-01

Plate-bounding subduction zone thrust systems are the source of major earthquakes and tsunamis, but their mechanics and internal structure remain poorly understood and relatively little-studied compared to faults in continental crust. Exposures in exhumed accretionary wedges present an opportunity to study seismogenic subduction thrusts in detail. In the Marin Headlands, a series of thrusts imbricates mechanically distinct lithologic units of the Mesozoic Franciscan Complex including pillow basalt, radiolarian chert, black mudstone, and turbidites. We examine variations in distribution and character of structure and vein occurrence in two exposures of the Rodeo Cove thrust, a fossil plate boundary exposed in the Marin Headlands. We observe a lithologic control on the degree and nature of fault localization. At Black Sand Beach, deformation is localized in broad fault cores of sheared black mudstone. Altered basalts, thrust over greywacke, mudstone, and chert, retain their coherence and pillow structures. Veins are only locally present. In contrast, mudstone is virtually absent from the exposure 2 km away at Rodeo Beach. At this location, deformation is concentrated in the altered basalts, which display evidence of extensive vein-rock interaction. Altered basalts exhibit a pervasive foliation, which is locally disrupted by both foliation-parallel and cross-cutting carbonate-filled veins and carbonate cemented breccia. Veins are voluminous (~50%) at this location. All the structures are cut by anastomosing brittle shear zones of foliated cataclasite or gouge. Analyses of vein chemistry will allow us to compare the sources of fluids that precipitated the common vein sets at Rodeo Beach to the locally developed veins at Black Sand Beach. These observations lead us to hypothesize that in the absence of a mechanically weak lithology, elevated pore fluid pressure is required for shear failure. If so, the vein-rich altered basalt at Rodeo Beach may record failure of an igneous basement asperity.

Relationship between geohydrology and Upper Pleistocene-Holocene evolution of the eastern region of the Province of Buenos Aires, Argentina

NASA Astrophysics Data System (ADS)

Capítulo, Leandro Rodrigues; Kruse, Eduardo E.

2017-07-01

The Upper Pleistocene-Holocene geological evolution, which is characterized by its landscape-forming energy and is related to geological and geomorphological complexity, has an impact on the groundwater dynamics of coastal aquifers. The geological configuration of a sector of the east coast of the Province of Buenos Aires was analyzed, as well as its connection with the geological and geomorphological history of the region during the Late Pleistocene and Holocene, and its influence on the regional and local geohydrological behaviour. This analysis was based on the application of the concept of hydrofacies. Boreholes were drilled and sampled (with depths of up to 40 m), and vertical electrical sounding, electrical tomography and pumping tests were undertaken. The description of the cutting samples by means of a stereo microscope, the interpretation of satellite images, and the construction of lithological and hydrogeological profiles and flow charts were carried out in the laboratory, and then integrated in a GIS. The identification of the lithological units and their distribution in the area allowed the construction of an evolutionary geological model for the Late Pleistocene and Holocene. Three aquifer units can be recognized: one of Late Pleistocene age (hydrofacies E) and the other two of Holocene age (hydrofacies A and C); their hydraulic connection depends on the occurrence and thickness variation of the aquitard units (hydrofacies B and D). The approach adopted allows the examination of the possibilities for groundwater exploitation and constitutes an applied conceptual framework to be taken into consideration when developing conceptual and numerical models at the local and regional scales.

Geology of the Smythii and Marginis Region of the Moon: Using Integrated Remotely Sensed Data

NASA Technical Reports Server (NTRS)

Gillis, Jeffrey J.; Spudis, Paul D.

2000-01-01

We characterized the diverse and complex geology of the eastern limb region of the Moon using a trio of remote-sensing data sets: Clementine, Lunar Prospector, and Apollo. On the basis of Clementine-derived iron and titanium maps we classify the highlands into low-iron (3-6 wt % FeO) and high-iron (6-9 wt % FeO) units. The association of the latter with basalt deposits west of Smythii basin suggests that the highland chemical variation is the result of mixing between basalt and highland lithologies. Mare Smythii and Mare Marginis soils are compositionally similar, containing moderate iron (15-18 wt % FeO) and titanium (2.5-3.5 wt % TiO2). Smythii basin, in addition to the basalt deposits, contains an older, moderate-albedo plains unit. Our investigation reveals that the dark basin plains unit has a distinct albedo, chemistry, and surface texture and formed as a result of impact-mixing between highland and mare lithologies in approximately equal proportions. Clementine iron and maturity maps show that swirls along the northern margin of Mare Marginis have the same iron composition as the surrounding nonswirl material and indicate that the swirl material is bright because of its low agglutinate content. Gravity data for the eastern limb show high, positive Bouguer gravity anomalies for areas of thin basalt cover (e.g., Smythii basin and complex craters Joliot, Lomonosov, and Neper). We deduce that the uplift of dense mantle material is the primary (and mare basaltic fill the secondary) source for generating the concentration of mass beneath large craters and basins.

Sedimentary features of the Blackhawk formation (Cretaceous) at Sunnyside, Carbon County, Utah

USGS Publications Warehouse

Maberry, John O.

1968-01-01

The Blackhawk Formation at Sunnyside, Utah, was deposited along the western margin of the Western Interior Cretaceous sea during southeastward withdrawal of the sea. Sand was the dominant type of land-derived sediment deposited in the Sunnyside district during the regressive phases. Sand bodies prograded seaward in response to changing sediment supply from a source west of Sunnyside. Where conditions were favorable for the accumulation of vegetable material, peat deposits formed and were later changed to bituminous Coal by diagenesis. Studies of the coal bed show that the coals were formed from accumulation of small, low-growing plants and plant debris that was transported into the area of accumulation. Remains of large plants in the coals are rare. Trace fossils, which are tracks, trails and burrows formed by organisms and preserved in the rock, are extremely abundant in the Blackhawk rocks. These biogenic sedimentary structures are common in Cretaceous deposits throughout the western United States. Trace fossil distribution in the rocks is controlled by the depositional environment preferred by their creators. A study of the trace fossils of a. locality allows a more precise determination of the conditions during deposition of the sediments. Water depth, bottom conditions, salinity, current velocity and amount of suspended nutrients in the water are some of the environmental factors that may be reconstructed by studying trace fossils. The Blackhawk Formation at Sunnyside comprises the members, the Kenilworth Member and the Sunnyside Member. Field studies show that the formation may be further subdivided in the Sunnyside district., according to the precepts of units of mappable thickness and similar lithologic characteristics. The Blackhawk pinches out eastward and north. ward into the Mancos Shale, and names for submembers become meaningless. Names are of value in the region of interest, however, because of the prominence of the named units. Coal mining is the main industry of the Book Cliffs region. Mines of the Sunnyside district are plagued by coal mine bumps, which are sudden, catastrophic releases of stress in the coal. Bumps cause loss of life, property age, and loss of profit to mining companies. Bumps occur when shear stress built up in the coal exceeds the shear Strength of the coal. Differential overburden pressure, faulting and tectonic activity, and lithology and structure of roof rocks are factors which influence bumps. Petroleum and natural gas (methane), which occur locally in pockets in the roof rocks above coal beds, may be diagenetic products of organic-rich sediments.

Integrating geologic and satellite radar data for mapping dome-and-basin patterns in the In Ouzzal Terrane, Western Hoggar, Algeria

NASA Astrophysics Data System (ADS)

Deroin, Jean-Paul; Djemai, Safouane; Bendaoud, Abderrahmane; Brahmi, Boualem; Ouzegane, Khadidja; Kienast, Jean-Robert

2014-11-01

The In Ouzzal Terrane (IOT) located in the north-western part of the Tuareg Shield forms an elongated N-S trending block, more than 400 km long and 80 km wide. It involves an Archaean crust remobilized during a very high-temperature metamorphic event related to the Palaeoproterozoic orogeny. The IOT largely crops out in the rocky and sandy desert of Western Hoggar. It corresponds mainly to a flat area with some reliefs composed of Late Panafrican granites, dyke networks or Cambrian volcanic rocks. These flat areas are generally covered by thin sand veneers. They are favorable for discriminating bedrock geological units using imaging radar, backscattering measurements, and field checking, because the stony desert is particularly sensitive to the radar parameters such as wavelength or polarization. The main radar data used are those obtained with the ALOS-PALSAR sensor (L-band), in ScanSAR mode (large swath) and Fine Beam modes. The PALSAR sensor has been also compared to ENVISAT-ASAR and to optical imagery. Detailed mapping of some key areas indicates extensive Archaean dome-and-basin patterns. In certain parts, the supracrustal synforms and orthogneiss domes exhibit linear or circular features corresponding to shear zones or rolling structures, respectively. The geological mapping of these dome-and-basin structures, and more generally of the Archaean and Proterozoic lithological units, is more accurate with the SAR imagery, particularly when using the L-band, than with the optical imagery. A quantitative approach is carried out in order to estimate the backscatter properties of the main rock types. Due to the large variety of configurations, radar satellite imagery such as ALOS PALSAR represents a key tool for geological mapping in arid region at different scales from the largest (e.g., 1:500,000) to the smallest (e.g., 1:50,000).

Cell Based Associations: A procedure for considering scarce and mixed mineral occurrences in predictive mapping

NASA Astrophysics Data System (ADS)

Tourlière, Bruno; Pakyuz-Charrier, Evren; Cassard, Daniel; Barbanson, Luc; Gumiaux, Charles

2015-05-01

Cell Based Association is an innovative mineral favorability procedure designed to answer special needs of the mining industry in data wise critical situations where usual favorability methods may not yield satisfactory results. Those situations relate to input data quality (e.g. clustered points, mixed and scarce data, approximate location) or some assumptions that are considered unreasonable (e.g. map areas relevance, conditional independence). The principle of CBA consists in replacing polygons of geological units with a square cell grid (hence the 'cell-based'). Each cell contains a range of units ('association') that are binary coded in terms of their presence (1) or absence (0) within study area. The loss of resolution inherent to this procedure is compensated by the enriched information contained in each cell owing to the notion of (lithological) association. Lithological associations are considered as binary spectra and as such are classified using Ascendant Hierarchical Clustering (AHC) thus obtaining a synthetic map of lithological associations. The prospectivity map shows as favourable the cells of the same AHC classes that the ones including mineral occurrences. It was observed that CBA can distinguish between different ore deposit varieties from a blended mineral occurrences data set. CBA can theoretically include any spatialized data (e.g. geophysics, structural data) as an extra variable to specify classification and narrow favourable areas. Doing so would make it an independent favorability mapping procedure and is still under development. Cell size in a grid is a critical parameter of the procedure; it must be compatible with the looked-for phenomena and should have a sufficient lithological variability. In addition to its use for producing favorability maps, a CBA-derived map could help in understanding the background information contained in geological maps. CBA can also be applied to other fields, such as agriculture and urban planning. Modelling of mineral prospectivity is a regional- or district scale mapping activity, whether field based or GIS based, which aims to delineate prospective areas for further exploration at the next higher scales of mapping. Notwithstanding the scale of mapping, mineral prospectivity is related to the degrees of presence and degrees of importance of individual pieces of spatial evidence of occurrence of mineral deposits of the type sought. That is, in a region or district under investigation, if there are more important pieces of spatial evidence in an area than in another area, then the former is considered to have higher prospectivity than the latter".

Assessment of lithogenic radioactivity in the Euganean Hills magmatic district (NE Italy).

PubMed

Tositti, Laura; Cinelli, Giorgia; Brattich, Erika; Galgaro, Antonio; Mostacci, Domiziano; Mazzoli, Claudio; Massironi, Matteo; Sassi, Raffaele

2017-01-01

The Euganean Hills of North East Italy have long been recognised as an area characterized by a higher than average natural radiation background. This is due to two main reasons: a) primary lithogenic radiation due to rhyolitic and trachytic outcrops, which are "acidic alkaline" magmatic rocks potentially enriched in uranium and thorium; b) secondary sources related to a geothermal field - widely exploited for spa tourism in the area since the Roman age - producing surface release of radon-enriched fluids. Though radioactivity levels in the Euganean district have been often investigated in the past - including recent works aimed at assessing the radiation doses from radon and/or total gamma radiation - no effort has been put so far into producing a thorough assessment linking radiation protection data to geological-structural features (lithology, faults, water, organic matter content, etc.). This work represents the first part of the interdisciplinary project "Geological and geochemical control on Radon occurrence and natural radioactivity in the Euganean Hills district (North-Eastern Italy)", aimed at producing detailed results of the actual radiation levels in connection mainly with lithological parameters. A detailed sampling strategy, based on lithostratigraphy, petrology and mineralogy, has been adopted. The 151 rock samples collected were analyzed by high resolution γ-ray spectrometry with ex situ HPGe detectors. Statistical and geostatistical analyses were performed, and outlier values of U and Th - possibly associated with anomalies in the geological formation - were identified. U, Th and K concentration maps were developed using both the entire database and then again after expunging the outliers; the two were then compared. In all maps the highest values can be associated to trachyte and rhyolite lithologies, and the lowest ones to sedimentary formations. The external dose due to natural radionuclides in the soil - the so called terrestrial gamma dose rate - has been calculated using the U, Th and K distribution measured in the bedrock samples. Copyright © 2016 Elsevier Ltd. All rights reserved.

Spatio-temporal variation in the hydrochemistry of Tawa River, Central India: effect of natural and anthropogenic factors.

PubMed

Mehto, Ashwini; Chakrapani, G J

2013-12-01

Tawa River is the biggest left bank tributary of the Narmada, the largest west-flowing river of the Indian peninsula. Central India enjoys a tropical climate, is highly urbanized, and the river flow is mostly controlled by monsoon; a large part of the population depend on rivers for their livelihood. Spatial and temporal variations in the hydrochemistry of the Tawa River were studied based on seasonal sampling along the course of the river and its tributaries. The study is important because not much data exist on small size rivers and the river processes spell out correctly in smaller basins. The monsoon season accounts for more than 70% of river water flow. The basin is characterized by silicate lithology; however, water chemistry is controlled by carbonate-rich soils and other weathering products of the silicate rocks, as indicated by the high (Ca + Mg)/(Na + K) ratios (>3.8). The values of the Na-normalized ratios of Ca(2+), Mg(2+), and HCO₃(-) suggest that both the carbonate and silicate lithology contribute to the hydrochemistry. On average, 42% of HCO₃(-) in the Tawa River water is contributed by silicate weathering and 58% from carbonate lithology. The water remains undersaturated with respect to calcite during the monsoon and post-monsoon seasons and supersaturated during the pre-monsoon season. A significant influence of mining in the basin and other industrial units is observed in water chemical composition.

A composite lithology log while drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tannenbaum, E.; Sutcliffe, B.; Franks, A.

A new method for producing a computerized composite lithology log (CLL) while drilling by integrating MWD (measurement while drilling) and surface data is described. At present, lithology logs are produced at the well site by mud loggers. They provide basic description and relative amounts of lithologies. Major difficulties are encountered in relating the cuttings to their original formations due to mixing in the drilling mud while transporting to the surface, sloughing shales, flawed sampling, etc. This results in a poor control on the stratigraphic sequence and on the depth of formation boundaries. A composite log can be produced after drillingmore » this additional inputs such as wireline, petrography, and paleontology. This process is labor intensive and expensive. The CLL integrates three types of data (MWD mechanical, MWD geophysical, and surface cuttings) acquired during drilling, in three time stages: (1) Real Time. MWD drilling mechanical data including the rate of penetration and the downhole torque. This stage would provide bed boundaries and some inferred lithology. This would assist the driller with immediate drilling decisions and determine formation tops for coring, casing point, and correlation. (2) MWD Time. Recomputation of the above by adding MWD geophysical data (gamma-ray, resistivity, neutron-density). This stage would upgrade the lithology inference, and give higher resolution to bed boundaries, (3) Lag Time. Detailed analysis of surface cuttings to confirm the inferred lithologies. This last input results in a high-quality CLL with accurate lithologies and bed boundaries.« less

Formation of ore minerals in metamorphic rocks of the German continental deep drilling site (KTB)

NASA Astrophysics Data System (ADS)

Kontny, A.; Friedrich, G.; Behr, H. J.; de Wall, H.; Horn, E. E.; Möller, P.; Zulauf, G.

1997-08-01

The German Continental Deep Drilling Program (KTB) drilled a 9.1 km deep profile through amphibolite facies metamorphic rocks and reached in situ temperatures of 265°C. Each lithologic unit is characterized by typical ore mineral assemblages related to the regional metamorphic conditions. Paragneisses contain pyrrhotite + rutile + ilmenite ± graphite, metabasic units bear ilmenite + rutile + pyrrhotite ± pyrite, and additionally, the so-called variegated units yield pyrrhotite + titanite assemblages. In the latter unit, magnetite + ilmenite + rutile + titanite assemblages related to the lower amphibolite facies breakdown of ilmenite-hematite solid solution also occur locally. Retrograde hydrothermal mineralization which commenced during Upper Carboniferous times is characterized by the following geochemical conditions: (1) low saline Na-K-Mg-Cl fluids with sulfur and oxygen fugacities at the pyrite-pyrrhotite buffer and temperatures of 400-500°C, (2) fluids with CO2, CH4±N2, andpH, Eh, sulfur, and oxygen fugacity in the stability field of graphite + pyrite at temperatures of 280-350° and (3) moderate to high saline Ca-Na-Cl fluids with CH4+ N2; sulfur and oxygen fugacity are in the stability field of pyrrhotite at temperatures <300°C. The latter environment is confirmed by in situ conditions found at the bottom of the deep drilling. Monoclinic, ferrimagnetic pyrrhotite is the main carrier of magnetization which disappears below about 8.6 km, corresponding to in situ temperatures of about 250°C. Below this depth, hexagonal antiferromagnetic pyrrhotite with a Curie temperature of 260°C is the stable phase. Temperature-dependent transformation of pyrrhotite and the reaching of its Curie isotherm within the Earth crust are one of the striking results of the KTB deep drilling project.

Geochemistry of Archean Mafic Amphibolites from the Amsaga Area, West African Craton, Mauritania: What Is the Message?

NASA Astrophysics Data System (ADS)

El Atrassi, F.; Debaille, V.; Mattielli, N. D. C.; Berger, J.

2014-12-01

While Archean terrains are mainly composed of a TTG (Tonalite-trondhjemite-granodiorite) suite, more mafic lithologies such as amphibolites are also a typical component of those ancient terrains. Although mafic rocks represent only ~10% of the Archean cratons, they may provide key evidence of the role and nature of basaltic magmatism in the formation of the Archean crust as well as the evolution of the Archean mantle. This study focuses on the Archean crust from the West African Craton in Mauritania (Amsaga area). The Amsaga Archean Crust mainly consists of TTG and thrust-imbricated slices of mafic volcanic rocks, which have been affected by polymetamorphic events from the amphibolite to granulite facies. Our main objectives aim to the identification of the mafic lithology origin and a better understanding of their role in the continental crust emplacement. Our petrological observations show that these amphibolites have fine to medium granoblastic and nematoblastic textures. The amphibolites are dominated by amphibolite-facies mineral assemblages (mainly amphibole and plagioclase), but garnet and clinopyroxene occur in a few samples. Two groups are distinct in their geochemical characteristics (major and trace elements), although both have tholeiitic basalt composition. The first group show LREE-enriched patterns and negative Nb-Ta anomalies. The second group is characterized by near-flat LREE patterns and flat HREE patterns. This second group clearly shows no Nb-Ta anomalies. The first group could be related to arc-like basalts, as it is many similarities with some Archean amphibolites probably formed in a supra-subduction zone, for instance the volcanic rocks from the southern edge of the Isua Supracrustal Belt. On the contrary, the second group has a MORB-like signature which is more unusual during the Archean. Different scenarios will be discussed regards to the Archean geodynamics.

Geology and mineral deposits of the Carlile quadrangle, Crook County, Wyoming

USGS Publications Warehouse

Bergendahl, M.H.; Davis, R.E.; Izett, G.A.

1961-01-01

The Carlile quadrangle-is along the northwestern flank of the Black Hills uplift in Crook County, Wyo. The area-is primarily one of canyons and divides that are a result of downcutting by the Belle Fourche River and its tributaries through an alternating succession of sandstone, siltstone, and mudstone or shale beds. The present topography is also influenced by the regional structure, as reflected by the beds that dip gently westward and by the local structural features such as anticlines, domes, synclines, basins, and terraces, which are superimposed upon the regional setting. Rocks exposed include shale and thin limestone and sandstone beds belonging to the Redwater shale member of the Sundance formation and to the Morrison formation, both of Late Jurassic age; sandstone, siltstone, and mudstone of the Lakota and Fall River formations of Early Cretaceous age; and shale and sandstone of the Skull Creek shale, Newcastle sandstone, and Mowry shale, also of Early Cretaceous age. In the southwestern part of the quadrangle rocks of the Upper Cretaceous series are exposed. These include the Belle Fourche shale, Greenhorn formation, and Carlile shale. Gravel terraces, landslide debris, and stream alluvium comprise the surficial deposits. The Lakota and Fall River formations, which make up the Iriyan Kara group, contain uranium deposits locally in the northern Black Hills. These formations were informally subdivided in order to show clearly the vertical and lateral distribution of the sandstone, siltstone, and mudstone facies within them.The Lakota was subdivided into a sandstone unit and an overlying mudstone unit; the Fall River was subdivided, in ascending order, into a siltstone unit, a mudstone unit, a sandstone unit, and an upper unit. The lithologic character of the Lakota changes abruptly locally, and the units are quite inconsistent with respect to composition, thickness, and extent. This is in contrast to a notable consistency in the lithologic character and thickness among all the Fall River units, with the exception of the upper unit. Petrographic studies on selected samples of units from both formations show differences in composition between Lakota and Fall River rocks.The Carlile quadrangle lies immediately east of the monocline that marks the outer limit of the Black Hills uplift, and the rocks in this area have a regional dip of less than 2° outward from the center of the uplift. Superimposed upon the regional uplift are many subordinate structural features anticlines, synclines, domes, basins, and terraces which locally modify the regional features. The most pronounced of these subordinate structural features are the doubly-plunging Pine Ridge, Oil Butte, and Dakota Divide anticlines, and the Eggie Creek syncline. Stress throughout the area was relieved almost entirely through folding; only a few small nearly vertical normal faults were found within the quadrangle.Uranium has been mined from the Carlile deposit, owned by the Homestake Mining Co. The ore minerals, carnotite and tyuyamnuite occur in a sandstone lens that is enclosed within relatively impermeable clayey beds in the mudstone unit of the Lakota formation. The ore also includes unidentified black vanadium minerals and possibly coffinite. Uranium minerals are more abundant in and adjacent to thicker carbonaceous and silty seams in the sandstone lens. A mixture of fine-grained calcium carbonate and calcium sulfate fills the interstices between detrital quartz grains in mineralized sandstone. Selenium and arsenic are more abundant in samples that are high in uranium. Drilling on Thorn Divide about 1 mile west of the Carlile mine has roughly outlined concentrations of a sooty black uranium mineral associated with pyrite In two stratigraphic intervals of the Lakota formation. One is in the same sandstone lens that contains the ore at the Carlile mine; the other is in conglomeratic sandstone near the base of the Lakota. These deposits are relatively deep, and no mining has been attempted. The mineralogy of the Carlile deposits and the lithologic features of the sandstone host rock suggest that uranium and vanadium were transported in the high-valent state by carbonate or sulfate solutions, were extracted from solution by organic material, and were reduced to low-valent states to form an original assemblage of oxides and silicates. These primary minerals were oxidized in place, and the present carnotite-tyuyamunite assemblage was formed. In general, radioactivity analyses correspond fairly closely with chemical analyses of uranium, thus it is believed that only minor solution and migration of uranium has occurred since the present suite of oxidized minerals was formed. The factors responsible for ore localization are not clear, but probably a combination of three lithologic and structural elements contributed to provide a favorable environment for precipitating uranium from aqueous solutions: abundant carbonaceous material or pyrite in a thin, permeable sandstone enclosed within relatively thick impermeable clays; local structural basins; and a regional structural setting involving a broad syncline between two anticlines. The structural features controlled the regional flow of ground water and the lithologic features controlled the local rate of flow and provided the proper chemical environment for uranium deposition. Bentonite has been mined from an opencut in the Mowry shale in the southwest part of the quadrangle. A bentonite bed in the Newcastle sandstone also seems to be of minable thickness and quality. Exploration for petroleum has been unsuccessful within the quadrangle; however, some wells that yielded oil were recently drilled on small anticlines to the west and southeast. It is possible that similar structural features in the Carlile area, that were previously overlooked, may be equally productive.

Structural investigations in the Massif-Central, France

NASA Technical Reports Server (NTRS)

Scanvic, J. Y.

1974-01-01

This survey covered the French Massif-Central (where crystalline and volcanic rocks outcrop) and its surrounding sedimentaries, Bassin de Paris, Bassin d'Aquitaine and Rhodanian valley. One objective was the mapping of fracturing and the surveying of its relationship with known ore deposits. During this survey it was found that ERTS imagery outlines lithology in some sedimentary basins. On the other hand, in a basement area, under temperature climate conditions, lithology is rarely expressed. These observations can be related to the fact that band 5 gives excellent results above sedimentary basins in France and generally band 7 is the most useful in a basement area. Several examples show clearly the value of ERTS imagery for mapping linear features and circular structures. All the main fractures are identified with the exception of new ones found both in sedimentaries and basement areas. Other interesting findings concern sun elevation which, stereoscopic effect not being possible, simulates relief in a better way under certain conditions.

Reasons of different colors in the ignimbrite lithology: micro-XRF and confocal Raman spectrometry method.

PubMed

Koralay, Tamer; Kadioglu, Yusuf Kagan

2008-03-01

Medium to large volume ignimbrites usually show vertical changes in terms of color, mineral components, texture and geochemistry. Determination of vertical changes in single extensive ignimbrite flow unit is difficult and requires careful studies. Color changes in ignimbrite flow units are very important for earth scientists. This may cause to identify the same ignimbrite series with different definition. Incesu ignimbrite has a wide distribution in the Central Anatolian Volcanic Province (CAVP). It is classified into three levels as lower, middle and upper according to color and welding degree. There is a sharp contact between the lower and middle level. The lower level is dark brown to black in color and the middle level has pinkish red to red color. The present paper focuses on the investigation of color changes between the ignimbrite levels by using micro-XRF and confocal Raman spectrometry. Micro-XRF and Raman spectrometry studies were performed on the polished thin sections of the lower and middle levels with different compositions. These differences were because of the compositional changes of K and slightly Fe elements distribution within the matrix. The dark brown to black color of the lower level was related to the high concentration of the K and Fe relatively to the middle level. Confocal Raman spectrometry investigations exhibited the matrix of the lower level mainly composed of anorthoclase, supporting the results of the micro-XRF.

Biostratigraphic data from Upper Cretaceous formations-eastern Wyoming, central Colorado, and northeastern New Mexico

USGS Publications Warehouse

Merewether, E.A.; Cobban, W.A.; Obradovich, J.D.

2011-01-01

Lithological and paleontological studies of outcrops of Upper Cretaceous formations were conducted at 12 localities in eastern Wyoming, central Colorado, and northeastern New Mexico. The sequence extends upward from the top of the Mowry Shale, or age-equivalent rocks, through the Graneros Shale, Greenhorn Limestone, Carlile Shale, Niobrara Formation, Pierre Shale, and Fox Hills Sandstone, or age-equivalent formations, to the top of the Laramie Formation, or laterally equivalent formations. The strata are mainly siliciclastic and calcareous, with thicknesses ranging from about 3,300 ft in northeastern New Mexico to as much as 13,500 ft in eastern Wyoming. Deposition was mainly in marine environments and molluscan fossils of Cenomanian through Maastrichtian ages are common. Radiometric ages were determined from beds of bentonite that are associated with fossil zones. The Upper Cretaceous formations at the 12 study localities are herein divided into three informal time-stratigraphic units based on fossil content and contact relations with adjacent strata. The basal unit in most places extends from the base of the Graneros to the top of the Niobrara, generally to the horizon of the fossil Scaphites hippocrepis, and spans a period of about 14 million years. The middle unit generally extends from the top of the Niobrara to the approximate middle of the Pierre, the horizon of the fossil Baculites gregoryensis, and represents a period of about 5 million years. The upper unit includes strata between the middle of the Pierre and the top of the Upper Cretaceous Series, which is the top of the Laramie Formation or of laterally equivalent formations; it represents a period of deposition of as much as 11 million years. Comparisons of the collections of fossils from each outcrop with the complete sequence of Upper Cretaceous index fossils can indicate disconformable contacts and lacunae. Widespread disconformities have been found within the Carlile Shale and between the Carlile Shale and the Niobrara Formation. Less extensive disconformities are within the Greenhorn Formation, the Niobrara Formation, and the Pierre Shale.

Chelyabinsk - a rock with many different (stony) faces: An infrared study

NASA Astrophysics Data System (ADS)

Morlok, Andreas; Bischoff, Addi; Patzek, Markus; Sohn, Martin; Hiesinger, Harald

2017-03-01

In order to provide spectral ground truth data for remote sensing applications, we have measured mid-infrared spectra (2-18 μm) of three typical, well-defined lithologies from the Chelyabinsk meteorite that fell on February 15, 2013, near the city of Chelyabinsk, southern Urals, Russia. These lithologies are classified as (a) moderately shocked, light lithology, (b) shock-darkened lithology, and (c) impact melt lithology. Analyses were made from bulk material in four size fractions (0-25 μm, 25-63 μm, 63-125 μm, and 125-250 μm), and from additional thin sections. Characteristic infrared features in the powdered bulk material of the moderately shocked, light lithology, dominated by olivine, pyroxene and feldspathic glass, are a Christiansen feature (CF) between 8.5 and 8.8 μm; a transparency feature (TF) in the finest size fraction at ∼13 μm, and strong reststrahlen bands (RB) at ∼9.1 μm, 9.5 μm, 10.3 μm, 10.8 μm, 11.2-11.3 μm, 12 μm, and between 16 and 17 μm. The ranges of spectral features for the micro-FTIR spots show a wider range than those obtained in diffuse reflectance, but are generally similar. With increasing influence of impact shock from 'pristine' LL5 (or LL6) material (which have a low or moderate degree of shock) to the shock-darkened lithology and the impact melt lithology as endmembers, we observe the fading/disappearing of spectral features. Most prominent is the loss of a 'twin peak' feature between 10.8 and 11.3 μm, which turns into a single peak. In addition, in the 'pure' impact melt "endmember lithology" features at ∼9.6 μm and ∼9.1 μm are also lost. These losses are most likely correlated with decreasing amounts of crystal structure as the degree of shock melting increases. These changes could connect mid-infrared features with stages for shock metamorphism (Stöffler et al., 1991): Changes up to shock stage S4 would be minor, the shock darkened lithology could represent S5 and the impact melt lithology S6 and higher. Similarities of the Chelyabinsk spectra to those of other LL chondrites indicate that the findings of this study could be related to this group of meteorites in general.

Lithological and land-use based assessment of heavy metal pollution in soils surrounding a cement plant in SW Europe.

PubMed

Cutillas-Barreiro, Laura; Pérez-Rodríguez, Paula; Gómez-Armesto, Antía; Fernández-Sanjurjo, María José; Álvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino; Arias-Estévez, Manuel; Nóvoa-Muñoz, Juan Carlos

2016-08-15

We study the influence of phasing out a cement plant on the heavy metal (Hg, Pb and Cr) content in the surrounding soils, taking into account factors often neglected, such as contributions due to local lithology or land use. The range of total Hg was 10-144µg kg(-1), reaching up to 41 and 145mgkg(-1) for total contents of Pb and Cr, respectively. Forest soils showed higher concentration of Hg than prairie soils, indicating the importance of land use on the accumulation of volatile heavy metals in soils. In forest soils, total Hg showed a trend to decrease with soil depth, whereas in prairie soils the vertical pattern of heavy metal concentrations was quite homogeneous. In most cases, the distance to the cement plant was not a factor of influence in the soils content of the analyzed heavy metals. Total Pb and Cr contents in soils nearby the cement plant were quite similar to those found in the local lithology, resulting in enrichment factor values (EF's) below 2. This suggests that soil parent material is the main source of these heavy metals in the studied soils, while the contribution of the cement plant to Pb and Cr soil pollution was almost negligible. On the contrary, the soils surrounding the cement plant accumulate a significant amount of Hg, compared to the underlying lithology. This was especially noticeable in forest soils, where Hg EF achieved values up to 36. These results are of relevance, bearing in mind that Hg accumulation in soils may be an issue of environmental concern, particularly in prairie soils, where temporal flooding can favor Hg transformation to highly toxic methyl-Hg. In addition, the concurrence of acid soils and total-Cr concentrations in the range of those considered phytotoxic should be also stressed. Copyright © 2016 Elsevier B.V. All rights reserved.

Geochemical and Geophysical Analysis of Holocene-aged Sediments from Southeastern Tulare Lake, CA

NASA Astrophysics Data System (ADS)

Prosser, L.; Jackson, B.; Roza, J.

2015-12-01

Tulare Lake is located in the San Joaquin Valley of California west of the Sierra Nevada mountains (Preston, 1981). The Poso Canal trench locality is located in the southeastern portion of Tulare Lake in the Ton Tachi lake plane south of the Atwell Island sand spit. This area was chosen because these sediments lie beneath a road bed that predates agricultural tilling, preserving late-Holocene lake sediments. Sediments from trench TL13-7C were sampled for geophysical and geochemical analyses in order to create a higher resolution lake-level history during the late-Holocene than had been possible using only lithologic descriptions. The new record is comprised of grain size, clay percentage, carbon/nitrogen (C/N) ratios, total inorganic carbon (TIC), total organic carbon (TOC), and nitrogen (N) analyses taken at 2-cm intervals over 181-cm of section comprising four lithologic units. From oldest to youngest, Unit 1A consists of relatively equal and steady percentages of clay, silt, and sand, and relatively low C/N ratios, TIC, TOC, and N, suggesting an unproductive lake and relatively deep lake levels at this high elevation site. Fluctuating C/N ratios, a steady decrease in clay percentage, and a steady increase in sand percentage in Unit 1B suggests periods of flooding and fluctuating lake levels and eventually shallow evaporative lake conditions, as evidenced by a considerable and sudden increase in TIC (to 4.51%) in Unit 2. In addition to the drastic change in TIC, Unit 2 shows evidence of a large influx of terrestrial organic matter perhaps transported by floods by an increase in sand percentage and two pronounced spikes in C/N ratios to 38 and 65 (Meyers and Lallier-Verges, 1999). Unit 3 shows low but steady levels of clay and sand percentages, and higher but steady levels of silt. Levels of TIC, TOC, C/N, and N are all steady, with relatively higher levels of TOC and N, which are indicators of high lake level and productivity (Cohen, 2003). Unit 4 is very similar to Unit 3, however toward the upper region of the unit, sand percentages increased with a slight increase in TIC, suggesting a relatively shallower lake. This record will be used to test lake-level models for Tulare Lake put forth by Blunt and Negrini (in press) and Jackson (2015).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Potter, P.E.; Maynard, J.B.; Pryor, W.A.

Studies of shales in the Appalachian area are reported (mainly in the form of abstracts of reports or manuscripts). They discuss the geology, lithology, stratigraphy, radioactivity, organic matter, the isotopic abundance of carbon and sulfur isotopes, etc. of shales in this area with maps. One report discusses Devonian paliocurrents in the central and northern Appalachian basin. Another discusses sedimentology of the Brallier Formation. The stratigraphy of upper Devonian shales along the southern shore of Lake Erie was also studied. (LTN)

Influence of Climate and Lithology on Soil Phosphorus

NASA Astrophysics Data System (ADS)

Wilson, S. G.; Margenot, A. J.; O'Geen, A. T.; Dahlgren, R. A.

2016-12-01

Climate and lithology are master variables of pedogenesis. We hypothesize that differences in parent material composition will influence the outcome of soil P fractionation, in concert with climate and the relative degree of chemical weathering. Here, we investigate a novel climo-lithosequence to elucidate the influence of lithology and climate on P dynamics. Three climosequences (elevational transects) spanning four climatic zones (Blue-Oak, Ponderosa Pine, White fir and Red fir), and three bedrock lithologies (basalt, andesite and granodiorite) were investigated across the Sierra Nevada and southern Cascades. Replicate soil samples were collected by genetic horizon at twelve sites (4 climate zones x 3 lithologies) and characterized by a modified Hedley P fractionation method to quantify P into operationally defined pools. Initial results from the fractionation of andesite and basalt transects (granodiorite forthcoming) show large climatic and lithologic effects on soil P fractions, suggesting that the distribution of soil P and the trajectory of P transformations are significantly influenced by lithology as well as climate. For example, in the climatic zone of least weathering (Red fir), all soil P fractions showed significant lithologic effects. In contrast, with increased weathering, parent material effects on soil P fractions become progressively muted, so that in the zone of most intense weathering (Ponderosa Pine), soil P fractions such as Ca-Pi (1 M HCl-Pi) and labile-Pi (Resin Pi + NaHCO3-Pi), no longer show an influence from lithology. Additionally, significant climatic effects were noted for labile-Pi, Ca-Pi and Fe/Al-Pi (0.1 M NaOH-Pi). A strong positive correlation was observed between poorly crystalline Fe/Al-(hydr)oxides (oxalate extractable Fe and Al) and Fe/Al-Pi (p<0.0001). Conversely, a strong negative correlation was observed between crystalline Fe-oxides (inferred by citrate-dithionite extractable Fe) and Fe/Al-Pi (p<0.0001). Results suggest that P dynamics in soils are strongly influenced not only by climate and the relative degree of chemical weathering, but also lithology, especially during the early stages of pedogenesis. Therefore, parent material and climate may interact more strongly than previously thought to regulate P biogeochemistry.

Digital geologic map and GIS database of Venezuela

USGS Publications Warehouse

Garrity, Christopher P.; Hackley, Paul C.; Urbani, Franco

2006-01-01

The digital geologic map and GIS database of Venezuela captures GIS compatible geologic and hydrologic data from the 'Geologic Shaded Relief Map of Venezuela,' which was released online as U.S. Geological Survey Open-File Report 2005-1038. Digital datasets and corresponding metadata files are stored in ESRI geodatabase format; accessible via ArcGIS 9.X. Feature classes in the geodatabase include geologic unit polygons, open water polygons, coincident geologic unit linework (contacts, faults, etc.) and non-coincident geologic unit linework (folds, drainage networks, etc.). Geologic unit polygon data were attributed for age, name, and lithologic type following the Lexico Estratigrafico de Venezuela. All digital datasets were captured from source data at 1:750,000. Although users may view and analyze data at varying scales, the authors make no guarantee as to the accuracy of the data at scales larger than 1:750,000.

Conditioning geostatistical simulations of a heterogeneous paleo-fluvial bedrock aquifer using lithologs and pumping tests

NASA Astrophysics Data System (ADS)

Niazi, A.; Bentley, L. R.; Hayashi, M.

2016-12-01

Geostatistical simulations are used to construct heterogeneous aquifer models. Optimally, such simulations should be conditioned with both lithologic and hydraulic data. We introduce an approach to condition lithologic geostatistical simulations of a paleo-fluvial bedrock aquifer consisting of relatively high permeable sandstone channels embedded in relatively low permeable mudstone using hydraulic data. The hydraulic data consist of two-hour single well pumping tests extracted from the public water well database for a 250-km2 watershed in Alberta, Canada. First, lithologic models of the entire watershed are simulated and conditioned with hard lithological data using transition probability - Markov chain geostatistics (TPROGS). Then, a segment of the simulation around a pumping well is used to populate a flow model (FEFLOW) with either sand or mudstone. The values of the hydraulic conductivity and specific storage of sand and mudstone are then adjusted to minimize the difference between simulated and actual pumping test data using the parameter estimation program PEST. If the simulated pumping test data do not adequately match the measured data, the lithologic model is updated by locally deforming the lithology distribution using the probability perturbation method and the model parameters are again updated with PEST. This procedure is repeated until the simulated and measured data agree within a pre-determined tolerance. The procedure is repeated for each well that has pumping test data. The method creates a local groundwater model that honors both the lithologic model and pumping test data and provides estimates of hydraulic conductivity and specific storage. Eventually, the simulations will be integrated into a watershed-scale groundwater model.

Mineralogy of iron sulfides in CM1 and CI1 lithologies of the Kaidun breccia: Records of extreme to intense hydrothermal alteration

NASA Astrophysics Data System (ADS)

Harries, Dennis; Zolensky, Michael E.

2016-06-01

The polymict Kaidun microbreccia contains lithologies of C-type chondrites with euhedral iron sulfide crystals of hydrothermal origin. Our FIB-TEM study reveals that acicular sulfides in a CM1 lithology are composed of Fe-rich pyrrhotite with nonintegral vacancy superstructures (NC-pyrrhotite), troilite, and pentlandite, all showing distinct exsolution textures. Based on phase relations in the Fe-Ni-S system, we constrain the temperature of formation of the originally homogeneous monosulfide solid solution to the range of 100-300 °C. In some crystals the exsolution of pentlandite and the microtextural equilibration was incomplete, probably due to rapid cooling. We use thermodynamic modeling to constrain the physicochemical conditions of the extreme hydrothermal alteration in this lithology. Unless the CM1 lithology was sourced from a large depth in the parent body (internal pressure >85 bar) or the temperatures were in the lower range of the interval determined, the water was likely present as vapor. Previously described light δ34S compositions of sulfides in Kaidun's CM1 lithology are likely due to the loss of 34S-enriched H2S during boiling. Platy sulfide crystals in an adjacent, intensely altered CI1 lithology are composed of Fe-poor, monoclinic 4C-pyrrhotite and NC-pyrrhotite and probably formed at lower temperatures and higher fS2 relative to the CM1 lithology. However, a better understanding of the stability of Fe-poor pyrrhotites at temperatures below 300 °C is required to better constrain these conditions.

Lithological mapping of Kanjamalai hill using hyperspectral remote sensing tools in Salem district, Tamil Nadu, India

NASA Astrophysics Data System (ADS)

Arulbalaji, Palanisamy; Balasubramanian, Gurugnanam

2017-07-01

This study uses advanced spaceborne thermal emission and reflection radiometer (ASTER) hyperspectral remote sensing techniques to discriminate rock types composing Kanjamalai hill located in the Salem district of Tamil Nadu, India. Kanjamalai hill is of particular interest because it contains economically viable iron ore deposits. ASTER hyperspectral data were subjected to principal component analysis (PCA), independent component analysis (ICA), and minimum noise fraction (MNF) to improve identification of lithologies remotely and to compare these digital data results with published geologic maps. Hyperspectral remote sensing analysis indicates that PCA (R∶G∶B=2∶1∶3), MNF (R∶G∶B=3∶2∶1), and ICA (R∶G∶B=1∶3∶2) provide the best band combination for effective discrimination of lithological rock types composing Kanjamalai hill. The remote sensing-derived lithological map compares favorably with a published geological map from Geological Survey of India and has been verified with ground truth field investigations. Therefore, ASTER data-based lithological mapping provides fast, cost-effective, and accurate geologic data useful for lithological discrimination and identification of ore deposits.

A composite lithology log while drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tannenbaum, E.; Sutcliffe, B.; Franks, A.

A new method for producing a computerized composite lithology log (CLL) while drilling by integrating MWD (measurement while drilling) and surface data is described. The CLL integrates three types of data (MWD mechanical, MWD geophysical, and surface cuttings) acquired during drilling, in three time stages: (1) Real Time. MWD drilling mechanical data including the rate of penetration and the downhole torque. This stage would provide bed boundaries and some inferred lithology. This would assist the driller with immediate drilling decisions and determine formation tops for coring, casing point, and correlation. (2) MWD Time. Recomputation of the above by adding MWDmore » geophysical data (gamma-ray, resistivity, neutron-density). This stage would upgrade the lithology inference, and give higher resolution of bed boundaries. (3) Lag Time. Detailed analysis of surface cuttings to confirm the inferred lithologies. This last input will result in a high-quality CLL with accurate lithologies and bed boundaries. The log will serve the geologist as well as the driller, petrophysicist, and reservoir engineer. It will form the basis for more comprehensive formation evaluation while drilling by adding hydrocarbon and MWD log data.« less

The role of rock anisotropy in developing non-Andersonian faults: staircase trajectories for strike-slip faults

NASA Astrophysics Data System (ADS)

Barchi, M. R.; Collettini, C.; Lena, G.

2012-04-01

Thrust and normal faults affecting mechanically heterogeneous multilayers often show staircase trajectories, where flat segments follow less competent units. Within flat segments the initiation/reactivation angle, θ, which is the angle that the fault makes with the σ1 direction, is different from that predicted by the Andersonian theory. This suggests that fault trajectory is mainly controlled by rock anisotropy instead of frictional properties of the material. Our study areas are located in the Umbria-Marche fold-thrust belt, within the Northern Apennines of Italy. The area is characterized by a lithologically complex multilayer, about 2000 m thick, consisting of alternated competent (mainly calcareous) and less competent (marls or evaporites) units. At the outcrop scale, some units show a significant mechanical layering, consisting of alternated limestones and shales. Due to the complex tectonic evolution of the Apennines, well developed sets of conjugate normal, thrust and strike-slip faults are exposed in the region. The study outcrop, Candigliano Gourge, is characterized by steep (dip > 60°) NE dipping beds, affected by conjugate sets of strike-slip faults, exposed in the eastern limb of a NE verging anticline. The faults develop within the Marne a Fucoidi Fm., a Cretaceous sedimentary unit, about 70 m thick, made of competent calcareous beds (about 20 cm thick), separated by marly beds (1-20 cm thick). The conjugate strike-slip faults are formed after the major folding phase: in fact the strike-slip faults cut both minor folds and striated bedding surfaces, related to syn-folding flexural slip. Faults show marked staircase trajectories, with straight segments almost parallel to the marly horizons and ramps cutting through the calcareous layers. Slip along these faults induces local block rotation of the competent strata, dilational jogs (pull-aparts), extensional duplexes and boudinage of the competent layers, while marly levels are strongly laminated. In order to reconstruct the σ1 direction, calcite veins syntectonic to strike-slip faulting, have been used to constrain the σ1-σ2 plane: fixing the σ2 direction at the conjugate fault intersection, the σ1 is oriented N15°, forming an angle of about 70° with the bedding direction. Once constrained the σ1 direction, we have calculated the θ angle that is comprised between 40° and 55°, resulting therefore larger than expected from Andersonian theory, i.e. 22°-32° for friction coefficient in the range of 0.5-1.0. Initiation/reactivation angles, θ, as a function of the different lithologies, are less than 35° for calcareous beds, 50°-70° for the marly and clayey layers, and around 60° for the black shales. Our studies, focused on strike-slip small displacement faults, show that: 1) irrespective of the σ1 orientation, ramp and flat form along competent and less competent material respectively and 2) the overall fault orientation/initiation is at high-angle to the σ1 direction. Our results suggest that rock anisotropy and layering are one of the possible causes for faulting at high angle to the σ1 direction, i.e. fault weakness. Further studies are required to up-scale the results of our outcrop-based study to crustal scale structures.

A nationwide classification of New Zealand aquifer properties

NASA Astrophysics Data System (ADS)

Westerhoff, Rogier; Tschritter, Constanze; Rawlinson, Zara; White, Paul

2017-04-01

Groundwater plays an essential role in water provision for domestic, industrial and agricultural use. Groundwater is also vital for ecology and environment, since it provides baseflow to many streams, rivers and wetlands. As groundwater is a 'hidden' resource that is typically poorly understood by the public, simple and informative maps can assist to enhance awareness for understanding groundwater and associated environmental issues. The first national aquifer map for New Zealand (2001) identified 200 aquifers at a scale of approximately 1:5 Million. Subsequently, regional councils and unitary authorities have updated their aquifer boundaries using a variety of methods. However, with increasing demand of groundwater in New Zealand and drought impacts expected to be more significant in the future, more consistent and more advanced aquifer characterisation and mapping techniques are needed to improve our understanding of the available resources. Significant resources have gone into detailed geological mapping in recent years, and the New Zealand 1:250,000 Geological Map (QMAP) was developed and released as a seamless GIS database in 2014. To date, there has been no national assessment of this significant data set for aquifer characterisation purposes. This study details the use of the QMAP lithological and chrono-stratigraphic information to develop a nationwide assessment of hydrogeological units and their properties. The aim of this study is to map hydrogeological units in New Zealand, with a long-term goal to use this as a basis for a nationally-consistent map of aquifer systems and aquifer properties (e.g., hydraulic conductivity estimates). Internationally accepted aquifer mapping studies were reviewed and a method was devised that classifies hydrogeological units based on the geological attributes of the QMAP ArcGIS polygons. The QMAP attributes used in this study were: main rock type; geological age; and secondary rock type. The method was mainly based on values of permeability after global, continental and New Zealand studies. The classification followed a tiered workflow. Tier 1 ('Hydrolithological units') consisted of the classification of only the main rock type, based on median permeability value. Tier 2 ('Hydrogeological units') consisted of a combined classification of main rock type and age, assuming that permeability shows an exponential decay over geological age. Tier 3 ('Hydrogeological units') included all three attributes, where the permeabilities of main and secondary rock types were averaged with weighting. Tier 4 was a simplification of the 10 classes in Tier 3 to four 'Aquifer Potential' classes, i.e., 'Poor', 'Low', 'Medium', and 'High'. The results show a good match with existing overlaying maps of aquifer boundaries The map is capable of refining aquifer boundaries at the regional scale where these boundaries have not been updated since 2001. Additionally, the map provides a quick and simple way to communicate hydrogeological information. This fundamental dataset is essential for future studies of the impact of climate and humans on groundwater in New Zealand. Future work will include categorising geological system knowledge (e.g., depositional environment) to allow for 3D mapping and characterisation, compilation and incorporation of nation-wide measured hydraulic conductivity values, including uncertainty, and linking with other national data sets.

Altitudes and thicknesses of hydrogeologic units of the Ozark Plateaus aquifer system in Arkansas, Kansas, Missouri, and Oklahoma

USGS Publications Warehouse

Westerman, Drew A.; Gillip, Jonathan A.; Richards, Joseph M.; Hays, Phillip D.; Clark, Brian R.

2016-09-29

A hydrogeologic framework was constructed to represent the altitudes and thicknesses of hydrogeologic units within the Ozark Plateaus aquifer system as part of a regional groundwater-flow model supported by the U.S. Geological Survey Water Availability and Use Science Program. The Ozark Plateaus aquifer system study area is nearly 70,000 square miles and includes parts of Arkansas, Kansas, Missouri, and Oklahoma. Nine hydrogeologic units were selected for delineation within the aquifer system and include the Western Interior Plains confining system, the Springfield Plateau aquifer, the Ozark confining unit, the Ozark aquifer, which was divided into the upper, middle, and lower Ozark aquifers to better capture the spatial variation in the hydrologic properties, the St. Francois confining unit, the St. Francois aquifer, and the basement confining unit. Geophysical and well-cutting logs, along with lithologic descriptions by well drillers, were compiled and interpreted to create hydrologic altitudes for each unit. The final compiled dataset included more than 23,000 individual altitude points (excluding synthetic points) representing the nine hydrogeologic units within the Ozark Plateaus aquifer system.

Isopach and structure contour maps of the Burro Canyon(?) Formation in the Mesa Golondrina and Mesa de los Viejos areas, Chama Basin, New Mexico

USGS Publications Warehouse

Ridgley, Jennie L.

1983-01-01

In the Chama Basin a wequence of conglomerate, sandstone, and red, gray-green, and pale-purple mudstone occurs stratigraphically between the Upper Jurassic Morrison Formation and Upper Cretaceous Dakota Sandstone. This stratigraphic interval has been called the Burro Canyon Formation by several workers (Craig and others, 1959; Smith and others, 1961; Saucier, 1974). Although similarities in lithology and stratigraphic position exist between this unit and the Burro Canyon Formation in Colorado, no direct correlation has been made between the two. For this reason the unit in the Chama Basin is called the Burro Canyon(?) Formation. 

Hydrocarbon potential of pre-Pennsylvanian rocks in Roosevelt County, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pitt, W.D.

The hydrocarbon potential of pre-Pennsylvanian rocks in Roosevelt County was appraised from data available in published reports, scout tickets, lithology logs, and other well data at the log libraries in Roswell and Socorro, New Mexico, and Midland, Texas. Elevations from lithology logs were used when differing from scout tickets or other sources. Thickness and data other than lithology logs were assumed to be sufficiently accurate if they fitted the control obtained by contouring. The lithology and reservoir potential of the systems of rock that subcrop beneath the Pennsylvanian System in Roosevelt County are summarized.

The Triassic upwelling system of Arctic Alaska

NASA Astrophysics Data System (ADS)

Yurchenko, I.; Graham, S. A.

2017-12-01

The Middle to Upper Triassic Shublik Formation of Arctic Alaska is a laterally and vertically heterogeneous rock unit that has been analyzed both in outcrop and in the subsurface. The Shublik Formation sediments are distinguished by a characteristic set of lithologies that include glauconitic, phosphatic, organic-rich, and cherty facies consistent with a coastal upwelling zone deposition interpretation. It is often recognized by abundance of impressions and shells of distinctive Triassic bivalves. To understand main controls on lithofacies distributions, this study reviews and refines lithologic and paleoenvironmental interpretations of the Shublik Formation, and incorporates the newly acquired detailed geochemical analyses of two complete Shublik cores. This work focuses on organic geochemistry (analyses of biomarkers and diamondoids), chemostratigraphy (hand-held XRF), and iron speciation analysis to reconstruct paleoproductivity and redox conditions. Based on the available evidence, during Shublik deposition, an upwelling-influenced open shelf resulted in high nutrient supply that stimulated algal blooms leading to high net organic productivity, reduced water transparency, oxygen deficiency, and water column stratification. Evidence of such eutrophic conditions is indicated by the lack of photic benthic organisms, bioturbation and trace fossils, and dominance of the monospecific light-independent epibenthic bivalves. The flat, subcircular, thin shells of these carbonate-secreting organisms allowed them to adapt to dysoxic conditions, and float on soft, soupy, muddy substrate. The distinctive clay- and organic-rich facies with abundant bivalves occurred on the mid to outer stable broad shelf, and were deposited when organic productivity at times overlapped with periods of increased siliciclastic input controlled by sea level and changes in local sediment dispersal systems, and therefore are more spatially and temporally localized than the widespread clay-poor facies. The overall lithofacies distribution in the Shublik Formation can therefore be described by the interplay of sea level, detrital sediment input, local bathymetry and hydrodynamic conditions without requiring changes in organic sources input or redox conditions.

Investigation of the influence of lineaments, lineament intersections and geology on groundwater yield in the basement complex terrain of Ondo State, Southwestern Nigeria

NASA Astrophysics Data System (ADS)

Akinluyi, Francis O.; Olorunfemi, Martins O.; Bayowa, Oyelowo G.

2018-03-01

The influence of lineaments, lineament intersections and geology on the groundwater yield of the basement terrain of Ondo State was investigated using optical remote sensing data, Aster DEM, geology, and borehole yield data. Landsat-7 ETM+ and Aster DEM were processed to generate composite lineament map. The study area was traversed by five (5) main lineament populations trending N-S, NE-SW, E-W, ENE-WSW, NNW-SSE. Boreholes sited on lineament exhibited a yield range of between 0.8 and 1.28 l/s with an average yield of 1.04 l/s. Boreholes sited close to lineament gave groundwater yield values of between 0.5 and 1.28 l/s and an average yield of 1 l/s, while boreholes located outside lineament gave groundwater yield range of between 0.2 and 1.26 l/s with an average yield of 0.98 l/s. The investigation of the hydrogeological characteristics of the lithologies by superimposing the yield data showed average yield of 0.98 l/s for migmatite gneiss biotite granite undifferentiated (M), 1.01 l/s for porphyritic granite (OGp), 1.03 l/s for medium- to coarse-grained (OGe), 1.17 l/s for pelitic schist undifferentiated (Su), 1.24 l/s for quartz schist and quartzite (Eq), 1.12 l/s for older granite undifferentiated (OGu), 0.5 l/s for slightly migmatised medium-grained granite-gneiss (gg) and 1.23 l/s for fine-grained flaggy quartzite and schists (Sf). The study concluded that borehole data located on or near lineaments or at intersection of lineaments gave higher yields more than those located before lineaments or outside lineaments, while quartz schist and quartzite exhibited the highest average groundwater yield of all the lithological units.

Spatial thermal radiometry contribution to the Massif armoricain and the Massif central (France) litho-structural study

NASA Technical Reports Server (NTRS)

Scanvic, J. Y. (Principal Investigator)

1980-01-01

The author has identified the following significant results. Although the limited number of images received did not permit construction of a thermal inertia map, important geological details were obtained in the areas of lithology and tectonics. Interpretation of day, night, and seasonal imagery resulted in differentiating broad calcareous and dolomitic units in the Causse Plateau. In the Massif amoricain, some granite massifs were delineated which were not observed by LANDSAT. Neotectonic faults were also revealed.

Regional geology subprogram: Geological interpretation of ERTS imagery of the occidental region of Bolivia

NASA Technical Reports Server (NTRS)

Brockmann, C. E. (Principal Investigator); Ayllon, R. B.

1973-01-01

The author has identified the following significant results. Using ERTS-1 imagery, it is possible to delimit great lithological units, folds, lineaments, faults, and in lesser degree unconformities. In the morphological aspect, the images show clearly the relief necessary for geological interpretation. The ERTS-1 images are important for the preparation of the geological and tectonic map of Bolivia, on a 1:1 million scale, if conventional methods of work are used as a base.

Explosives Washout Lagoons Soils Operable Unit Supplemental Investigation Technical and Environmental Management Support of Installation Restoration Technology Development Program Umatilla Depot Activity Hermiston, Oregon

DTIC Science & Technology

1992-04-15

an ofcial endorsement or approval of the use of such commercial products. This report may not be cited for purposes of advertisement . "EngineersM M7...Logs Appendix C. Laboratory Results of Soil Samples Appendix D. Concentration of Contaminants vs . Depth in Soils Appendix E. Lithologic Profiles of...dramatic difference in concentrations of explosives in areas outside the lagoons vs . concentrations beneath the lagoons. The results confirm that ES-I

The role of detachment and interlayer shear zones in the structural evolution of the southern Espinhaço range, eastern Brazil

NASA Astrophysics Data System (ADS)

Kuchenbecker, Matheus; Sanglard, Júlio Carlos Destro

2018-07-01

Sedimentary rocks usually show a significant mechanical anisotropy due to its layered nature. Because of this, they play an important role controlling rock deformation and the study of the deformation partitioning caused by rheological heterogeneities becomes a crucial step to understand the inversion of sedimentary basins. The detachment and interlayer shear zones, described at southern Espinhaço range, correspond to part of the structural collection that records the compressive deformation which is associated to the Brazilian-Pan African orogeny during Gondwana amalgamation. The mechanical contrast between lithological units is the main parameter of control for the occurrence of these zones which can be found with variable thickness from millimeter interlayer shear zones to regional-sized basement-cover detachment zones. The phyllitic layers are the most incompetent lithotype among metasedimentary rocks and they play an important role in the ductile-brittle regional deformation by accommodating much of the deformation during faulting and/or folding. Even though being a more competent rock, internal interlayer shear zones and other shear structures can be found in quartzite when in contact with weaker rocks. These structures accommodate a significant amount of deformation at the southern Espinhaço range and, because of this, they are of great value in understanding the inversion of the Espinhaço basins during West Gondwana assembly. The focus of the present paper is to discuss the main situations where interlayer shear occurs, to present a brief compendium of the main structures associated to this process and to add parameters to its recognition and interpretation.

Upper Cretaceous to Lower Miocene of the Subsilesian Unit (Western Carpathians, Czech Republic): stratotypes of formations revised

NASA Astrophysics Data System (ADS)

Bubík, Miroslav; Franců, Juraj; Gilíková, Helena; Otava, Jiří; Švábenická, Lilian

2016-06-01

Type sections/areas for all four formations distinguished in the sedimentary succession of the Subsilesian Unit on Czech territory were revisited and described. New data on lithology, sedimentology, fossil record, biostratigraphy, heavy-minerals and geochemical proxies are based on observations and analysis of these sections. The historical type section of the Frýdek Formation was destroyed during railway construction in 19th century. Outcrops of Campanian to Maastrichtian marls and sandstones on the southwestern slope of "Castle hill" at Frýdek, are proposed as a new type section. The Ostravice riverbed in Frýdlant nad Ostravicí was originally designated as the type area, not mentioning the particular section. This area, even when supplemented with Sibudov Creek, does not show all typical facies of the formation. The outcrops range from lowermost Eocene to Eocene-Oligocene transition. In the original description of the Menilite Formation Glocker mentioned several localities in the area covering the Ždanice, Subsilesian and Silesian units, not mentioning the principal one. The single sections, each not exceeding a thickness of 2 m, are not sufficient to be a type section. Instead of that, we propose the area between Paršovice and Bystřice pod Hostýnem, covering the historical localities, as the type area. The type locality of the Ženklava Formation is an outcrop in an unnamed creek in Ženklava according to the original definition. It seems to be reasonable to extend the type section to the whole 500 m long section of the creek with the outcrops that better illustrate the lithological variability of the formation. New biostratigraphic data allow assignment to late Egerian (Eggenburgian?).

Construction of 3-D geologic framework and textural models for Cuyama Valley groundwater basin, California

USGS Publications Warehouse

Sweetkind, Donald S.; Faunt, Claudia C.; Hanson, Randall T.

2013-01-01

Groundwater is the sole source of water supply in Cuyama Valley, a rural agricultural area in Santa Barbara County, California, in the southeasternmost part of the Coast Ranges of California. Continued groundwater withdrawals and associated water-resource management concerns have prompted an evaluation of the hydrogeology and water availability for the Cuyama Valley groundwater basin by the U.S. Geological Survey, in cooperation with the Water Agency Division of the Santa Barbara County Department of Public Works. As a part of the overall groundwater evaluation, this report documents the construction of a digital three-dimensional geologic framework model of the groundwater basin suitable for use within a numerical hydrologic-flow model. The report also includes an analysis of the spatial variability of lithology and grain size, which forms the geologic basis for estimating aquifer hydraulic properties. The geologic framework was constructed as a digital representation of the interpreted geometry and thickness of the principal stratigraphic units within the Cuyama Valley groundwater basin, which include younger alluvium, older alluvium, and the Morales Formation, and underlying consolidated bedrock. The framework model was constructed by creating gridded surfaces representing the altitude of the top of each stratigraphic unit from various input data, including lithologic and electric logs from oil and gas wells and water wells, cross sections, and geologic maps. Sediment grain-size data were analyzed in both two and three dimensions to help define textural variations in the Cuyama Valley groundwater basin and identify areas with similar geologic materials that potentially have fairly uniform hydraulic properties. Sediment grain size was used to construct three-dimensional textural models that employed simple interpolation between drill holes and two-dimensional textural models for each stratigraphic unit that incorporated spatial structure of the textural data.

Tectonic control of complex slope failures in the Ameka River Valley (Lower Gibe Area, central Ethiopia): Implications for landslide formation

NASA Astrophysics Data System (ADS)

Kycl, Petr; Rapprich, Vladislav; Verner, Kryštof; Novotný, Jan; Hroch, Tomáš; Mišurec, Jan; Eshetu, Habtamu; Tadesse Haile, Ezra; Alemayehu, Leta; Goslar, Tomasz

2017-07-01

Even though major faults represent important landslide controlling factors, the role the tectonic setting in actively spreading rifts plays in the development of large complex landslides is seldom discussed. The Ameka complex landslide area is located on the eastern scarp of the Gibe Gorge, approximately 45 km to the west of the Main Ethiopian Rift and 175 km to the southwest of Addis Ababa. Investigation of the complex landslide failures required a combination of satellite and airborne data-based geomorphology, geological field survey complemented with structural analysis, radiocarbon geochronology and vertical electric sounding. The obtained observations confirmed the multiphase evolution of the landslide area. We have documented that, apart from climatic and lithological conditions, the main triggering factor of the Ameka complex landslide is the tectonic development of this area. The E-W extension along the NNE-SSW trending Main Ethiopian Rift is associated with the formation of numerous parallel normal faults, such as the Gibe Gorge fault and the almost perpendicular scissor faults. The geometry of the slid blocks of coherent lithology have inherited the original tectonic framework, which suggests the crucial role tectonics play in the fragmentation of the compact rock-masses, and the origin and development of the Ameka complex landslide area. Similarly, the main scarps were also parallel to the principal tectonic features. The local tectonic framework is dominated by faults of the same orientation as the regional structures of the Main Ethiopian Rift. Such parallel tectonic frameworks display clear links between the extension of the Main Ethiopian Rift and the tectonic development of the landslide area. The Ameka complex landslide developed in several episodes over thousands of years. According to the radiocarbon data, the last of the larger displaced blocks (representing only 2% of the total area) most likely slid down in the seventh century AD. The main scarps, namely the high scarps in the western part, are unstable over the long term and toppling and falling-type slope movements can be expected here in the future.

Linking descriptive geology and quantitative machine learning through an ontology of lithological concepts

NASA Astrophysics Data System (ADS)

Klump, J. F.; Huber, R.; Robertson, J.; Cox, S. J. D.; Woodcock, R.

2014-12-01

Despite the recent explosion of quantitative geological data, geology remains a fundamentally qualitative science. Numerical data only constitute a certain part of data collection in the geosciences. In many cases, geological observations are compiled as text into reports and annotations on drill cores, thin sections or drawings of outcrops. The observations are classified into concepts such as lithology, stratigraphy, geological structure, etc. These descriptions are semantically rich and are generally supported by more quantitative observations using geochemical analyses, XRD, hyperspectral scanning, etc, but the goal is geological semantics. In practice it has been difficult to bring the different observations together due to differing perception or granularity of classification in human observation, or the partial observation of only some characteristics using quantitative sensors. In the past years many geological classification schemas have been transferred into ontologies and vocabularies, formalized using RDF and OWL, and published through SPARQL endpoints. Several lithological ontologies were compiled by stratigraphy.net and published through a SPARQL endpoint. This work is complemented by the development of a Python API to integrate this vocabulary into Python-based text mining applications. The applications for the lithological vocabulary and Python API are automated semantic tagging of geochemical data and descriptions of drill cores, machine learning of geochemical compositions that are diagnostic for lithological classifications, and text mining for lithological concepts in reports and geological literature. This combination of applications can be used to identify anomalies in databases, where composition and lithological classification do not match. It can also be used to identify lithological concepts in the literature and infer quantitative values. The resulting semantic tagging opens new possibilities for linking these diverse sources of data.

Metamorphic reactions in the Chaunskij mesosiderite

NASA Astrophysics Data System (ADS)

Petaev, M. I.; Brearley, A. J.

1994-07-01

The Chaunskij meteorite, found in 1985, recently has been found to be the most highly metamorphosed, shock-modified, and metal-rich mesosiderite. It contains approximately 10 vol% mono- and polymineralic troilite-phosphate-silicate inclusions, micrometers to centimeters in size. Two dominant silicate lithologies have been found in the inclusions. The primary 'igneous' lithology, making up the largest inclusion studied, is generally a microophitic fine-grained aggregate of pyroxene, plagioclase, and minor silica, with scattered coarser-grained granoblastic spots enriched in silica and troilite. The secondary 'metamorphic' lithology occurs as separate small inclusions and as larger areas in intimate contact with the 'igneous' lithology, separated by highly irregular boundaries from each other, in the largest inclusion. In small inclusions the metamorphic lithology consists of a fine-grained hornfelsic to granoblastic aggregate of cordierite, orthopyroxene, quartz, and whitlockite with variable amounts of opaque minerals. In the largest inclusion the metamorphic lithology is a generally granoblastic to poikiloblastic aggregate of cordierite and quartz with minor amounts of other minerals. The Opx-Chr mineral thermometer and the Cord-Sp barometer have been applied to estimate the conditions of Chaunskij metamorphism. The data for 16 Opx-Chr pairs from different inclusions and lithologies correspond to a temperature of 590 +/- 30 C. The data for 9 Cord-Chr pairs from different inclusions correspond to a pressure of 6.0 +/- 0.2 kbar. While the composition of spinel in Chaunskij much richer in Cr than were the spinels used to calibrate Cord-Sp barometer the estimated pressure is consistent with the occurrence in the igneous lithology of two small pyroxene grains enriched in the CaAl2SiO6 molecule, coexisting with quartz and plagioclase. This mineral assemblage is unstable below approximately 5 kbar at 600 C.

3.1 Ga crystallization age for magnesian and ferroan gabbro lithologies in the Northwest Africa 773 clan of lunar meteorites

NASA Astrophysics Data System (ADS)

Shaulis, B. J.; Righter, M.; Lapen, T. J.; Jolliff, B. L.; Irving, A. J.

2017-09-01

The Northwest Africa (NWA) 773 clan of meteorites is a group of paired and/or petrogenetically related stones that contain at least six different lithologies: magnesian gabbro, ferroan gabbro, anorthositic gabbro, olivine phyric basalt, regolith breccia, and polymict breccia. Uranium-lead dates of baddeleyite in the magnesian gabbro, ferroan gabbro, and components within breccia lithologies of paired lunar meteorites NWA 773, NWA 3170, NWA 6950, and NWA 7007 indicate a chronologic link among the meteorites and their components. A total of 50 baddeleyite grains were analyzed and yielded weighted average 207Pb-206Pb dates of 3119.4 ± 9.4 (n = 27), 3108 ± 20 (n = 13), and 3113 ± 15 (n = 10) Ma for the magnesian gabbro, ferroan gabbro, and polymict breccia lithologies, respectively. A weighted average date of 3115.6 ± 6.8 Ma (n = 47/50) was calculated from the baddeleyite dates for all lithologies. A single large zircon grain found in a lithic clast in the polymict breccia of NWA 773 yielded a U-Pb concordia date of 3953 ± 18 Ma, indicating a much more ancient source for some of the components within the breccia. A U-Pb concordia date of apatite and merrillite grains from the magnesian gabbro and polymict breccia lithologies in NWA 773 is 3112 ± 33 Ma, identical to the baddeleyite dates. Magnesian and ferroan gabbros, as well as the dated baddeleyite and Ca-phosphate-bearing detritus in the breccia lithologies, formed during the same igneous event at about 3115 Ma. These data also strengthen proposed petrogenetic connections between magnesian and ferroan gabbro lithologies, which represent some of the youngest igneous rocks known from the Moon.

Composition and Maturity of Apollo 16 Regolith Core 60013/14

NASA Technical Reports Server (NTRS)

Korotev, Randy T.; Morris, Richard V.

1993-01-01

Samples from every half-centimeter dissection interval of double drive tube 60013/14 (sections 60013 and 60014) were analyzed by magnetic techniques for Fe concentration and surface maturity parameter I(sub s)/ Fe(O), and by neutron activation for concentrations of 25 lithophile and siderophile elements. Core 60013/14 is one of three regolith cores taken in a triangular array 40-50 m apart on the Cayley plains during Apollo 16 mission to the Moon. The core can be divided into three zones based both on I(sub s)/FeO and composition. Unit A (0-44 cm depth) is compositionally similar to other soils from the surface of the central region of the site and is mature throughout, although maturity decreases with depth. Unit B (44-59 cm) is submature and compositionally more feldspathic than Unit A. Regions of lowest maturity in Unit B are characterized by lower Sm/Sc ratios than any soil obtained from the Cayley plains as a result of some unidentified lithologic component with low surface maturity. The component is probably some type of mafic anorthosite that does not occur in such high abundance in any of the other returned soils. Unit C (59-62 cm) is more mature than Unit B and compositionally equivalent to an 87: 13 mixture of soil such as that from Unit A and plagioclase such as found in ferroan anorthosite. Similar soils, but containing greater abundances of anorthosite (plagioclase), are found at depth in the other two cores of the array. These units of immature to submature soil enriched to varying degrees (compared to the mature surface soil) in ferroan anorthosite consisting of approx. 99% plagioclase are the only compositionally distinct subsurface similarities among the three cores. Each of the cores contains other units that are compositionally dissimilar to any soil unit in the other two cores. These compositionally distinct units probably derive from local subsurface blocks deposited by the event(s) that formed the Cayley plains. The ferroan anorthosite with approx. 99% plagioclase, however, must represent some subsurface lithology that is significant on the scale of tens of meters. The compositional uniformity of the surface soil (0-10 cm depth) over distances of kilometers reflects the large-scale uniformity of the plains deposits; the fine- structure reflects small-scale nonuniformity and the inefficiency of the impact-mixing process at depths as shallow as even one meter.

A record of astronomically forced climate change in a late Ordovician (Sandbian) deep marine sequence, Ordos Basin, North China

NASA Astrophysics Data System (ADS)

Fang, Qiang; Wu, Huaichun; Hinnov, Linda A.; Wang, Xunlian; Yang, Tianshui; Li, Haiyan; Zhang, Shihong

2016-07-01

The late Ordovician Pingliang Formation on the southwestern margin of the Ordos Basin, North China, consists of rhythmic alternations of shale, limestone, and siliceous beds. To explore the possible astronomical forcing preserved in this lithological record, continuous lithological rank and magnetic susceptibility (MS) stratigraphic series were obtained from a 34 m thick section of the Pingliang Formation at Guanzhuang. Power spectral analysis of the MS and rank series reveal 85.5 cm to 124 cm, 23 cm to 38 cm, and 15 cm to 27 cm thick sedimentary cycles that in ratio match that of late Ordovician short eccentricity, obliquity and precession astronomical cycles. The power spectrum of the MS time series, calibrated to interpreted short orbital eccentricity cycles, aligns with spectral peaks to astronomical parameters, including 95 kyr short orbital eccentricity, 35.3 kyr and 30.6 kyr obliquity, and 19.6 kyr and 16.3 kyr precession cycles. The 15 cm to 27 cm thick limestone-shale couplets mainly represent precession cycles, and siliceous bed deposition may be related to both precession and obliquity forcing. We propose that precession-forced sea-level fluctuations mainly controlled production of lime mud in a shallow marine environment, and transport to the basin. Precession and obliquity controlled biogenic silica productivity, and temperature-dependent preservation of silica may have been influenced by obliquity forcing.

Fault geometry and mechanics of marly carbonate multilayers: An integrated field and laboratory study from the Northern Apennines, Italy

NASA Astrophysics Data System (ADS)

Giorgetti, C.; Collettini, C.; Scuderi, M. M.; Barchi, M. R.; Tesei, T.

2016-12-01

Sealing layers are often represented by sedimentary sequences characterized by alternating strong and weak lithologies. When involved in faulting processes, these mechanically heterogeneous multilayers develop complex fault geometries. Here we investigate fault initiation and evolution within a mechanical multilayer by integrating field observations and rock deformation experiments. Faults initiate with a staircase trajectory that partially reflects the mechanical properties of the involved lithologies, as suggested by our deformation experiments. However, some faults initiating at low angles in calcite-rich layers (θi = 5°-20°) and at high angles in clay-rich layers (θi = 45°-86°) indicate the important role of structural inheritance at the onset of faulting. With increasing displacement, faults develop well-organized fault cores characterized by a marly, foliated matrix embedding fragments of limestone. The angles of fault reactivation, which concentrate between 30° and 60°, are consistent with the low friction coefficient measured during our experiments on marls (μs = 0.39), indicating that clay minerals exert a main control on fault mechanics. Moreover, our integrated analysis suggests that fracturing and faulting are the main mechanisms allowing fluid circulation within the low-permeability multilayer, and that its sealing integrity can be compromised only by the activity of larger faults cutting across its entire thickness.

Lithofacies, Age, and Sequence Stratigraphy of the Carboniferous Lisburne Group in the Skimo Creek Area, Central Brooks Range

USGS Publications Warehouse

Dumoulin, Julie A.; Whalen, Michael T.; Harris, Anita G.

2008-01-01

The Lisburne Group, a mainly Carboniferous carbonate succession that is widely distributed across northern Alaska, contains notable amounts of oil and gas at Prudhoe Bay. Detailed studies of the Lisburne in the Skimo Creek area, central Brooks Range, delineate its lithofacies, age, conodont biofacies, depositional environments, and sequence stratigraphy and provide new data on its hydrocarbon source-rock and reservoir potential, as well as its thermal history, in this area. We have studied the Lisburne Group in two thrust sheets of the Endicott Mountains allochthon, herein called the Skimo and Tiglukpuk thrust sheets. The southern, Skimo Creek section, which is >900 m thick, is composed largely of even-bedded to nodular lime mudstone and wackestone intercalated with intervals of thin- to thick-bedded bioclastic packstone and grainstone. Some parts of the section are partially to completely dolomitized and (or) replaced by chert. A distinctive, 30-m-thick zone of black, organic-rich shale, lime mudstone, and phosphorite is exposed 170 m below the top of the Lisburne. The uppermost 40 m of section is also distinctive and made up of dark shale, lime mudstone, spiculite, and glauconitic grainstone. The northern, Tiglukpuk Creek section, which is similar to the Skimo Creek section but only ~760 m thick, includes more packstone and grainstone and less organic-rich shale. Analyses of conodonts and foraminifers indicate that both sections range in age from late Early Mississippian (Osagean) through Early Pennsylvanian (early Morrowan) and document a hiatus of at least 15 m.y. at the contact between the Lisburne and the overlying Siksikpuk Formation. No evidence of subaerial exposure was observed along this contact, which may represent a submarine erosional surface. Lithofacies and biofacies imply that the Lisburne Group in the study area was deposited mainly in midramp to outer-ramp settings. Deepest water strata are mud rich and formed below storm or fair-weather wave base on the outer ramp to outer midramp; shallowest facies are storm, sand-wave, and shoal deposits of the inner midramp to inner ramp. A relatively diverse, open-marine fauna occurs throughout much of the Lisburne in the study area, but some beds also contain clasts typical of more restricted, shallow-water environments that were likely transported seaward by storms and currents. Radiolarians are abundant in the shale and phosphorite unit at Skimo Creek and also occur in equivalent strata at Tiglukpuk Creek; high gamma-ray response and elevated total organic-carbon contents (max 5?8 weight percent) also characterize this unit at Skimo Creek. Lithologic, faunal, and geochemical data all suggest that these rocks formed mainly in an outer-ramp to basinal setting with low sedimentation rates, high productivity, and poorly oxygenated bottom water. Shale and mudstone at the top of the Lisburne Group accumulated in a similarly sediment starved, mainly outer ramp environment but lack comparable evidence for high nutrient and low oxygen levels during deposition. Vertical shifts in rock types and faunas delineate numerous parasequences and six probable third-order sequences in the study area; the same sequences are also recognized in the Lisburne Group to the east. Transgressive-system tracts in these sequences generally fine upward, whereas highstand-system tracts coarsen upward. Sequences in the Tiglukpuk Creek section are mostly thinner, contain thinner and more numerous parasequences, and accumulated in somewhat shallower settings than those in the Skimo Creek section. These differences reflect the more seaward position and, thus, increased accommodation space of the Skimo Creek section relative to the Tiglukpuk Creek section during deposition. Organic-rich calcareous shale in the shale and phosphorite unit has a cumulative thickness of at least 15 m and a lateral extent of >50 km; this lithology is the best potential hydrocarbon source rock in the Lisburne Group

Microbial biogeography of arctic streams: exploring influences of lithology and habitat.

PubMed

Larouche, Julia R; Bowden, William B; Giordano, Rosanna; Flinn, Michael B; Crump, Byron C

2012-01-01

Terminal restriction fragment length polymorphism and 16S rRNA gene sequencing were used to explore the community composition of bacterial communities in biofilms on sediments (epipssamon) and rocks (epilithon) in stream reaches that drain watersheds with contrasting lithologies in the Noatak National Preserve, Alaska. Bacterial community composition varied primarily by stream habitat and secondarily by lithology. Positive correlations were detected between bacterial community structure and nutrients, base cations, and dissolved organic carbon. Our results showed significant differences at the stream habitat, between epipssamon and epilithon bacterial communities, which we expected. Our results also showed significant differences at the landscape scale that could be related to different lithologies and associated stream biogeochemistry. These results provide insight into the bacterial community composition of little known and pristine arctic stream ecosystems and illustrate how differences in the lithology, soils, and vegetation community of the terrestrial environment interact to influence stream bacterial taxonomic richness and composition.

Microbial Biogeography of Arctic Streams: Exploring Influences of Lithology and Habitat

PubMed Central

Larouche, Julia R.; Bowden, William B.; Giordano, Rosanna; Flinn, Michael B.; Crump, Byron C.

2012-01-01

Terminal restriction fragment length polymorphism and 16S rRNA gene sequencing were used to explore the community composition of bacterial communities in biofilms on sediments (epipssamon) and rocks (epilithon) in stream reaches that drain watersheds with contrasting lithologies in the Noatak National Preserve, Alaska. Bacterial community composition varied primarily by stream habitat and secondarily by lithology. Positive correlations were detected between bacterial community structure and nutrients, base cations, and dissolved organic carbon. Our results showed significant differences at the stream habitat, between epipssamon and epilithon bacterial communities, which we expected. Our results also showed significant differences at the landscape scale that could be related to different lithologies and associated stream biogeochemistry. These results provide insight into the bacterial community composition of little known and pristine arctic stream ecosystems and illustrate how differences in the lithology, soils, and vegetation community of the terrestrial environment interact to influence stream bacterial taxonomic richness and composition. PMID:22936932

O, Mg, and Si isotope distributions in the complex ultrarefractory CAI Efremovka 101.1: Assimilation of ultrarefractory, FUN, and regular CAI precursors

NASA Astrophysics Data System (ADS)

Aléon, Jérôme; Marin-Carbonne, Johanna; McKeegan, Kevin D.; El Goresy, Ahmed

2018-07-01

Oxygen, magnesium, and silicon isotopic compositions in the mineralogically complex, ultrarefractory (UR) calcium-aluminum-rich inclusion (CAI) E101.1 from the reduced CV3 chondrite Efremovka confirm that E101.1 is a compound CAI composed of several lithological units that were once individual CAIs, free-floating in the solar protoplanetary disk. Each precursor unit was found to have had its own thermal history prior to being captured and incorporated into the partially molten host CAI. Four major lithological units can be distinguished on the basis of their isotopic compositions. (1) Al-diopside-rich sinuous fragments, hereafter sinuous pyroxene, are 16O-rich (Δ17O ≤ -20‰) and have light Mg and Si isotopic compositions with mass fractionation down to -3.5‰/amu for both isotopic systems. We attribute these peculiar isotopic compositions to kinetic effects during condensation out of thermal equilibrium. (2) Spinel clusters are 16O-rich (Δ17O ∼ -22‰) and have Mg isotope systematics consistent with extensive equilibration with the host melt. This includes (i) δ25Mg values varying between + 2.6‰ and + 6.5‰ close to the typical value of host melilite at ∼+5‰, and (ii) evidence for exchange of radiogenic 26Mg with adjacent melilite as indicated by Al/Mg systematics. The spinel clusters may represent fine-grained spinel-rich proto-CAIs captured, partially melted, and recrystallized in the host melt. Al/Mg systematics indicate that both the sinuous pyroxene fragments and spinel clusters probably had canonical or near-canonical 26Al contents before partial equilibration. (3) The main CAI host (Δ17O ≤ -2‰) had a complex thermal history partially obscured by subsequent capture and assimilation events. Its formation, referred to as the "cryptic" stage, could have resulted from the partial melting and crystallization of a 16O-rich precursor that underwent 16O-depletion and a massive evaporation event characteristic of F and FUN CAIs (Fractionated with Unknown Nuclear effects). Alternatively, a 16O-rich UR precursor may have coagulated with a 16O-poor FUN CAI having 48Ca anomalies, as indicated by perovskite, before subsequent extensive melting. The Al/Mg systematics (2.4 × 10-5 ≤ (26Al/27Al)0‧ ≤ 5.4 × 10-5, where (26Al/27Al)0‧ is a model initial 26Al/27Al ratio per analysis spot) are best understood if the FUN component was 26Al-poor, as are many FUN CAIs. (4) A complete Wark-Lovering rim (WLR) surrounds E101.1. Its Mg and Si isotopic compositions indicate that it formed by interaction of the evaporated interior CAI with an unfractionated 16O-rich condensate component. Heterogeneities in 26Al content in WLR spinels (3.7 × 10-5 ≤ (26Al/27Al)0‧ ≤ 5.7 × 10-5) suggest that the previously reported age difference of as much as 300,000 years between interior CAIs and their WLRs may be an artifact resulting from Mg isotopic perturbations, possibly by solid state diffusion or mixing between the interior and condensate components. The isotopic systematics of E101.1 imply that 16O-rich and 16O-poor reservoirs co-existed in the earliest solar protoplanetary disk and that igneous CAIs experienced a 16O-depletion in an early high temperature stage. The coagulation of various lithological units in E101.1 and their partial assimilation supports models of CAI growth by competing fragmentation and coagulation in a partially molten state. Our results suggest that chemical and isotopic heterogeneities of unclear origin in regular CAIs may result from such a complex aggregation history masked by subsequent melting and recrystallization.

ERS-2 SAR and IRS-1C LISS III data fusion: A PCA approach to improve remote sensing based geological interpretation

NASA Astrophysics Data System (ADS)

Pal, S. K.; Majumdar, T. J.; Bhattacharya, Amit K.

Fusion of optical and synthetic aperture radar data has been attempted in the present study for mapping of various lithologic units over a part of the Singhbhum Shear Zone (SSZ) and its surroundings. ERS-2 SAR data over the study area has been enhanced using Fast Fourier Transformation (FFT) based filtering approach, and also using Frost filtering technique. Both the enhanced SAR imagery have been then separately fused with histogram equalized IRS-1C LISS III image using Principal Component Analysis (PCA) technique. Later, Feature-oriented Principal Components Selection (FPCS) technique has been applied to generate False Color Composite (FCC) images, from which corresponding geological maps have been prepared. Finally, GIS techniques have been successfully used for change detection analysis in the lithological interpretation between the published geological map and the fusion based geological maps. In general, there is good agreement between these maps over a large portion of the study area. Based on the change detection studies, few areas could be identified which need attention for further detailed ground-based geological studies.

Lithological and hydrochemical controls on distribution and speciation of uranium in groundwaters of hard-rock granitic aquifers of Madurai District, Tamil Nadu (India).

PubMed

Thivya, C; Chidambaram, S; Keesari, Tirumalesh; Prasanna, M V; Thilagavathi, R; Adithya, V S; Singaraja, C

2016-04-01

Uranium is a radioactive element normally present in hexavalent form as U(VI) in solution and elevated levels in drinking water cause health hazards. Representative groundwater samples were collected from different litho-units in this region and were analyzed for total U and major and minor ions. Results indicate that the highest U concentration (113 µg l(-1)) was found in granitic terrains of this region and about 10 % of the samples exceed the permissible limit for drinking water. Among different species of U in aqueous media, carbonate complexes [UO2(CO3)(2)(2-)] are found to be dominant. Groundwater with higher U has higher pCO2 values, indicating weathering by bicarbonate ions resulting in preferential mobilization of U in groundwater. The major minerals uraninite and coffinite were found to be supersaturated and are likely to control the distribution of U in the study area. Nature of U in groundwater, the effects of lithology on hydrochemistry and factors controlling its distribution in hard rock aquifers of Madurai district are highlighted in this paper.

Stable isotope study of antimony deposits in the Muratdagi region, western Turkey

NASA Astrophysics Data System (ADS)

Gokçe, A.; Spiro, B.

1994-09-01

The Muratdagi region is rich in antimony deposits having the following common characteristics: post Miocene age, location on the down-thrown blocks next to normal faults, in the vicinity of active or fossil thermal springs, and in contact with carbonate rocks. The isotopic composition of — 7‰. SMOW of the mineralizing fluid calculated from the measured ° 18O of quartz and the fluid inclusion microthermometry, is indicative of meteoric water origin. The ° 13C of the inclusion CO2 of — 19.1 to — 25.4‰ PDB is indicative of interaction with organic material-graphite. The ° 34S of stibnite — 3.6 to — 0.7‰ is, in view of the mineral assemblage, indicative of magmatic origin of the sulphur. A tightly confined set of structural, lithological, hydrological and geochemical features define a sequence of geochemical processes; formation of acid and reducing fluid, leaching and transport of antimony complexes and precipitation of stibnite within defined lithological units. The set of processes seems to have taken place within a space of 5000 m lateral and 1000 m vertical extension.

Statistical robustness of machine-learning estimates for characterizing a groundwater-surface water system, Southland, New Zealand

NASA Astrophysics Data System (ADS)

Friedel, M. J.; Daughney, C.

2016-12-01

The development of a successful surface-groundwater management strategy depends on the quality of data provided for analysis. This study evaluates the statistical robustness when using a modified self-organizing map (MSOM) technique to estimate missing values for three hypersurface models: synoptic groundwater-surface water hydrochemistry, time-series of groundwater-surface water hydrochemistry, and mixed-survey (combination of groundwater-surface water hydrochemistry and lithologies) hydrostratigraphic unit data. These models of increasing complexity are developed and validated based on observations from the Southland region of New Zealand. In each case, the estimation method is sufficiently robust to cope with groundwater-surface water hydrochemistry vagaries due to sample size and extreme data insufficiency, even when >80% of the data are missing. The estimation of surface water hydrochemistry time series values enabled the evaluation of seasonal variation, and the imputation of lithologies facilitated the evaluation of hydrostratigraphic controls on groundwater-surface water interaction. The robust statistical results for groundwater-surface water models of increasing data complexity provide justification to apply the MSOM technique in other regions of New Zealand and abroad.

Cenozoic stratigraphy and geologic history of the Tucson Basin, Pima County, Arizona

USGS Publications Warehouse

Anderson, S.R.

1987-01-01

This report was prepared as part of a geohydrologic study of the Tucson basin conducted by the U.S. Geological Survey in cooperation with the city of Tucson. Geologic data from more than 500 water supply and test wells were analyzed to define characteristics of the basin sediments that may affect the potential for land subsidence induced by groundwater withdrawal. The Tucson basin is a structural depression within the Basin and Range physiographic province. The basin is 1,000 sq mi in units area and trends north to northwest. Three Cenozoic stratigraphic unit--the Pantano Formation of Oligocene age, the Tinaja beds (informal usage) of Miocene and Pliocene age, and the Fort Lowell Formation of Pleistocene age--fill the basin. The Tinaja beds include lower, middle, and upper unconformable units. A thin veneer of stream alluvium of late Quaternary age overlies the Fort Lowell Formation. The Pantano Formation and the lower Tinaja beds accumulated during a time of widespread continental sedimentation, volcanism, plutonism, uplift, and complex faulting and tilting of rock units that began during the Oligocene and continued until the middle Miocene. Overlying sediments of the middle and upper Tinaja beds were deposited in response to two subsequent episodes of post-12-million-year block faulting, the latter of which was accompanied by renewed uplift. The Fort Lowell Formation accumulated during the Quaternary development of modern through-flowing the maturation of the drainage. The composite Cenozoic stratigraphic section of the Tucson basin is at least 20,000 ft thick. The steeply tilted to flat-lying section is composed of indurated to unconsolidated clastic sediments, evaporites, and volcanic rocks that are lithologically and structurally complex. The lithology and structures of the section was greatly affected by the uplift and exhumation of adjacent metamorphic core-complex rocks. Similar Cenozoic geologic relations have been identified in other parts of southern Arizona. (Author 's abstract)

Preliminary integrated geologic map databases for the United States: Digital data for the geology of southeast Alaska

USGS Publications Warehouse

Gehrels, George E.; Berg, Henry C.

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set of 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Use of remote sensing techniques for geological hazard surveys in vegetated urban regions. [multispectral imagery for lithological mapping

NASA Technical Reports Server (NTRS)

Stow, S. H.; Price, R. C.; Hoehner, F.; Wielchowsky, C.

1976-01-01

The feasibility of using aerial photography for lithologic differentiation in a heavily vegetated region is investigated using multispectral imagery obtained from LANDSAT satellite and aircraft-borne photography. Delineating and mapping of localized vegetal zones can be accomplished by the use of remote sensing because a difference in morphology and physiology results in different natural reflectances or signatures. An investigation was made to show that these local plant zones are affected by altitude, topography, weathering, and gullying; but are controlled by lithology. Therefore, maps outlining local plant zones were used as a basis for lithologic map construction.

Additional Sr Isotopic Heterogeneity in Zagami Olivine-Rich Lithology

NASA Technical Reports Server (NTRS)

Misawa, K.; Niihara, T.; Shih, C.-Y; Reese, Y. D.; Nyquist, L. E.; Yoneda, S.; Yamashita, H.

2012-01-01

Prior isotopic analyses of Zagami have established differing initial Sr-87/Sr-86 (ISr) ratios of among Zagami lithologies, fine-grained (FG), coarse-grained (CG), and dark mottled lithologies (DML)]. The Zagami sample (KPM-NLH000057) newly allocated from the Kanagawa Prefectural Museum of Natural History contained DML and the Ol-rich lithology which included more ferroan olivines (Ol-rich: Fa(sub 97- 99) vs late-stage melt pockets: Fa(sub 90-97)]). We have combined mineralogy-petrology and Rb-Sr isotopic studies on the Kanagawa Zagami sample, which will provide additional clues to the genesis of enriched shergottites and to the evolution of Martian crust and mantle

Environmental magnetism of Kucukcekmece Lagoon sediments (Istanbul): paleoclimate records for the last 3800 years in northwest Anatolia

NASA Astrophysics Data System (ADS)

Makaroglu, O.; Nowaczyk, N. R.; Cagatay, M. N.; Acar, D.; Akcer On, S.; Orbay, N.

2016-12-01

We present the results of high resolution mineral magnetic and geochemical analyses from the 512 cm long Core KCL12P2, recovered from the deepest basin of Küçükçekmece Lagoon (40.98° N, 28.76° E), located north of the Sea of Marmara. According to the age-depth model based on radiocarbon, paleomagnetic and global proxy correlation, the core sedimentary section covers the last 3800 years and consists of three different lithologies, based on lithological variations and down core mineral magnetic composition. Lithology A is composed of grey to brown laminated sediment that is siderite-rich as evidenced by the thermomagnetic analysis. It has low to intermediate Ca and Sr, low Ca/Ti and high Br (organic carbon). This lithology was deposited during relatively humid periods with high organic productivity and high terrigeneous input, which occurred during 3150-1700 a BP, 3600-3350 a and 1500 a BP-present. Lithology B consists of homogeneous black sediments characterized by the predominance of single magnetic domain (SD) and the highest magnetic susceptibility (100-2200x10-6), S-ratios (0.95 - 0.99), HIRM (100-2400) and SIRM/κLF (58-100kAm-1) values producing distinct peaks. The thickness of this lithology varies in thickness between 5 and 10 cm in the core. The thermomagnetic and mineral magnetic parameters indicate the predominance of greigite in lithology B, which occurred during 1500, 3200 and 3600 a BP some decadal periods after each seawater intrusion and establishment of high sulphate concentrations in the lagoon following each dry period represented by lithology C in the sequence. Lithology C is a homogeneous grey mud with low S-ratio, high κLF and high HIRM values indicating an increase in the content of high coercivity magnetic minerals. It is also characterized by high Ca, Sr and Ca/Ti and low Br (low organic carbon). The magnetic and geochemical composition of lithology C indicate that it was deposited during dry periods with low fresh water, nutrient and terrigenous inputs. Such dry periods occurred during 1500-1700 a BP, 3200-3400 a BP and 3600-3800 a BP. Latest archaeological findings with discovery of the water supply canals in the catchment area of the Küçükçekmece Lagoon corresponding to the dry periods support our climate records.

Northwest Africa 773: Lunar Mare Breccia with a Shallow-formed Olivine-Cumulate Component, Very-Low-Ti Heritage, and a KREEP Connection

NASA Technical Reports Server (NTRS)

Jolliff, B. L.; Korotev, R. L.; Zeigler, R. A.; Floss, C.; Haskin, L. A.

2003-01-01

Northwest Africa 773 is one of the more unusual lunar meteorites found in recent years because it contains a prominent clast lithology, which appears to be an olivine-rich cumulate and because it is a very-low-Ti (VLT) mare breccia with relatively high incompatible-trace-element concentrations and LREE/HREE enrichment. A lunar origin was verified by Fagan and coworkers on the basis of noble-gas contents, oxygen isotopes, and mineral compositions. Fagan et al. described two lithologies: (1) heterolithic impact breccia with a regolith component and (2) cumulus olivine gabbronorite. Here, we refer to these as the breccia (Bx) lithology and the olivine-cumulate (OC) lithology. The impact breccia components are predominantly volcanic (basaltic), and, in this context, the occurrence of the cumulus lithology is especially significant: is it related to the volcanic components or does it represent a deep-seated rock entrained by the basaltic magma as it rose to the surface? Elevated incompatible-element concentrations with more or less KREEP-like inter-element ratios and very-low-Ti concentrations distinguish both lithologies of this meteorite from Apollo mare basalts. Here, we summarize key compositional information (bulk and mineral), especially related to the OC lithology, to show that it formed at shallow depth and comes from a VLT ultramafic precursor that mixed with a KREEP-like trace-element component deep in the crust or upper mantle.

Petrophysical analysis of geophysical logs of the National Drilling Company-U.S. Geological Survey ground-water research project for Abu Dhabi Emirate, United Arab Emirates

USGS Publications Warehouse

Jorgensen, Donald G.; Petricola, Mario

1994-01-01

A program of borehole-geophysical logging was implemented to supply geologic and geohydrologic information for a regional ground-water investigation of Abu Dhabi Emirate. Analysis of geophysical logs was essential to provide information on geohydrologic properties because drill cuttings were not always adequate to define lithologic boundaries. The standard suite of logs obtained at most project test holes consisted of caliper, spontaneous potential, gamma ray, dual induction, microresistivity, compensated neutron, compensated density, and compensated sonic. Ophiolitic detritus from the nearby Oman Mountains has unusual petrophysical properties that complicated the interpretation of geophysical logs. The density of coarse ophiolitic detritus is typically greater than 3.0 grams per cubic centimeter, porosity values are large, often exceeding 45 percent, and the clay fraction included unusual clays, such as lizardite. Neither the spontaneous-potential log nor the natural gamma-ray log were useable clay indicators. Because intrinsic permeability is a function of clay content, additional research in determining clay content was critical. A research program of geophysical logging was conducted to determine the petrophysical properties of the shallow subsurface formations. The logging included spectral-gamma and thermal-decay-time logs. These logs, along with the standard geophysical logs, were correlated to mineralogy and whole-rock chemistry as determined from sidewall cores. Thus, interpretation of lithology and fluids was accomplished. Permeability and specific yield were calculated from geophysical-log data and correlated to results from an aquifer test. On the basis of results from the research logging, a method of lithologic and water-resistivity interpretation was developed for the test holes at which the standard suite of logs were obtained. In addition, a computer program was developed to assist in the analysis of log data. Geohydrologic properties were estimated, including volume of clay matrix, volume of matrix other than clay, density of matrix other than clay, density of matrix, intrinsic permeability, specific yield, and specific storage. Geophysical logs were used to (1) determine lithology, (2) correlate lithologic and permeable zones, (3) calibrate seismic reprocessing, (4) calibrate transient-electromagnetic surveys, and (5) calibrate uphole-survey interpretations. Logs were used at the drill site to (1) determine permeability zones, (2) determine dissolved-solids content, which is a function of water resistivity, and (3) design wells accordingly. Data and properties derived from logs were used to determine transmissivity and specific yield of aquifer materials.

An interpretation of the 1996 aeromagnetic data for the Santa Cruz basin, Tumacacori Mountains, Santa Rita Mountains, and Patagonia Mountains, south-central Arizona

USGS Publications Warehouse

Gettings, Mark E.

2002-01-01

High resolution aeromagnetic survey data flown at 250 m above the terrain and 250 m line spacing over the Santa Cruz Valley and the surrounding Tumacacori, Patagonia, and Santa Rita Mountains has been interpreted by correlation of the magnetic anomaly field and various derivative maps with geologic maps. Measurements of in-situ magnetic properties of several of the map units determined whether or not mapped lithologies were responsible for observed anomalies. Correlation of the magnetic anomaly field with mapped geology shows that numerous map units of volcanic and intrusive rocks from Jurassic Middle Tertiary in age are reversely polarized, some of which have not been previously reported. Trends derived from the magnetic anomaly data correlate closely with structures from major tectonic events in the geologic history of the area including Triassic-Jurassic crustal accretion and magmatism, Laramide magmatism and tectonism, northeast-southwest Mid-Tertiary extension, and east-west Basin and Range extension. Application of two textural measures to the magnetic anomaly data, number of peaks and troughs per km (a measure of roughness) and Euclidean length per km (a measure of amplitude), delineated areas of consistent magnetic anomaly texture. These measures were successful at the delineation of areas of consistent magnetic lithology both on the surface and in the subsurface beneath basin fill. Several areas of basement prospective for mineral resources beneath basin fill were identified.

The influence of geology and land use on arsenic in stream sediments and ground waters in New England, USA

USGS Publications Warehouse

Robinson, G.R.; Ayotte, J.D.

2006-01-01

Population statistics for As concentrations in rocks, sediments and ground water differ by geology and land use features in the New England region, USA. Significant sources of As in the surficial environment include both natural weathering of rocks and anthropogenic sources such as arsenical pesticides that were commonly applied to apple, blueberry and potato crops during the first half of the 20th century in the region. The variation of As in bedrock ground water wells has a strong positive correlation with geologic features at the geologic province, lithology group, and bedrock map unit levels. The variation of As in bedrock ground water wells also has a positive correlation with elevated stream sediment and rock As chemistry. Elevated As concentrations in bedrock wells do not correlate with past agricultural areas that used arsenical pesticides on crops. Stream sediments, which integrate both natural and anthropogenic sources, have a strong positive correlation of As concentrations with rock chemistry, geologic provinces and ground water chemistry, and a weaker positive correlation with past agricultural land use. Although correlation is not sufficient to demonstrate cause-and-effect, the statistics favor rock-based As as the dominant regional source of the element in stream sediments and ground water in New England. The distribution of bedrock geology features at the geologic province, lithology group and map unit level closely correlate with areas of elevated As in ground water, stream sediments, and rocks. ?? 2006 Elsevier Ltd. All rights reserved.

Yucatán subsurface stratigraphy: Implications and constraints for the Chicxulub impact

NASA Astrophysics Data System (ADS)

Ward, W. C.; Keller, G.; Stinnesbeck, W.; Adatte, T.

1995-10-01

Much of the discussion about the effects of an end-of-Cretaceous impact by a large extraterrestrial body in northwestern Yucatán has been done in the context of limited and partly erroneous published data on the Mesozoic stratigraphy of that area. Reexamination of cores and geophysical logs taken in several Pemex wells has produced improved lithologic and biostratigraphic correlation of the Jurassic to Maastrichtian section across the northern Yucatán peninsula. These data suggest that major disturbance of strata by an impact would have been confined to within about 100 km of the proposed impact center near Chicxulub. The only unusual lithologic unit is polymict breccia, which apparently was penetrated at or near the top of the Cretaceous section in all the deep wells of northern Yucatán. This breccia in Pemex wells Yucatán 1, 2, 4, 5A, and 6 is composed predominantly of detrital dolomite, limestone, and anhydrite clasts set in dolomitized carbonate mud matrix, which contains upper Maastrichtian foraminifers. These constituents, mixed with fragments of altered glass or melt rock, shocked quartz and feldspar, and basement rock, suggest an impact as the most likely origin for the breccia. The timing of brecciation is poorly constrained by biostratigraphic data. There is some evidence, however, that the breccia unit is overlain by about 18 m of uppermost Maastrichtian marls, suggesting an impact before the Cretaceous-Tertiary boundary. In addition, there may have been more than one episode of breccia deposition.

The geologic structure of part of the southern Franklin Mountains, El Paso County, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, W.R.; Julian, F.E.

1993-02-01

The Franklin Mountains are a west tilted fault block mountain range which extends northwards from the city of El Paso, Texas. Geologic mapping in the southern portion of the Franklin Mountains has revealed many previously unrecognized structural complexities. Three large high-angle faults define the boundaries of map. Twenty lithologic units are present in the field area, including the southernmost Precambrian meta-sedimentary rocks in the Franklin Mountains (Lanoria Quartzite and Thunderbird group conglomerates). The area is dominated by Precambrian igneous rocks and lower Paleozoic carbonates, but Cenozoic ( ) intrusions are also recognized. Thin sections and rock slabs were used tomore » describe and identify many of the lithologic units. The Franklin Mountains are often referred to as a simple fault block mountain range related to the Rio Grande Rift. Three critical regions within the study area show that these mountains contain structural complexities. In critical area one, Precambrian granites and rhyolites are structurally juxtaposed, and several faults bisecting the area affect the Precambrian/Paleozoic fault contact. Critical area two contains multiple NNW-trending faults, three sills and a possible landslide. This area also shows depositional features related to an island of Precambrian rock exposed during deposition of the lower Paleozoic rocks. Critical area three contains numerous small faults which generally trend NNE. They appear to be splays off of one of the major faults bounding the area. Cenozoic kaolinite sills and mafic intrusion have filled many of the fault zones.« less

Fresh and Salt Water Distribution in Passive Margin Sediments: Insights from Iodp Expedition 313 ON the New Jersey Margin

NASA Astrophysics Data System (ADS)

Lofi, J.; Inwood, J.; Proust, J.; Monteverde, D.; Loggia, D.; Basile, C.; Hayashi, T.; Stadler, S.; Fehr, A.; Pezard, P.

2012-12-01

For the first time in the history of international scientific drillings, the Integrated Ocean Drilling Program (IODP) mission-specific platform (MSP) Expedition 313 drilled three 631-755 m-deep boreholes on the middle shelf of a clastic passive margin. This expedition gathered a full set of geophysical data tied to drillcores with 80% of recovery. It offers a unique opportunity to access the internal structure of a siliciclastic system, at scales ranging from the matrix to the margin, and to correlate the geological skeleton with the spatial distribution and salinity of saturating fluids. In addition to the discovery of very low salinity pore water (<3g/l) at depths exceeding 400 m below the middle shelf, this expedition provides evidence for a multi-layered reservoir, with fresh/brackish water intervals alternating vertically with salty intervals. Our observations suggest that the processes controlling salinity distribution are strongly influenced by lithology, porosity and permeability. Saltier pore waters are recovered in less porous, more permeable, intervals whereas fresher pore waters are recovered in more porous, less permeable, intervals. Pore water concentrations are inversely correlated to the Thorium content, with high salinities in low Th intervals (i.e. sandy formations). The transition from fresher to saltier intervals is often marked by cemented horizons acting as permeability barrier. In the lower part of some holes, the salinity varies independently of lithology, suggesting different mechanisms and/or sources of salinity. We have developed a 2D model of permeability distribution along a dip transect of the margin, extrapolated from combined clinoform geometries observed on seismic data and sedimentary facies described on cores. This model clearly illustrates the importance of taking into account the spatial heterogeneity of geological system at several scales. Lithology reflects permeability at a small scale whereas seismic facies and system tracts can be used to infer the reservoir geometry at a larger scale. Four main reservoirs (R1 to R4) that are relatively disconnected have been identified. These are essentially developed in coarse-grained deposits observed either in some clinoform topsets (R4), in upper foresets (R2, R3), or in both of them (R1). R2 to R4 contain salty water while the most proximal reservoir R1, located close to the coastline, is saturated with fresh water, and may form the seaward extension of onshore aquifers. Each of these four reservoirs is separated by confining units of varied thicknesses and of relatively broad spatial extension. At the Expedition 313 drilling sites, the fresh waters stored in confining units have a post-deposition age and may have a fossil origin (Pleistocene low-stands?), whereas saltier water recovered in distal reservoirs (R2 to R4) penetrated at a later stage. Further work must be done to clarify the emplacement mechanisms. Future studies should focus on the inclusion of our 2D permeability model in a groundwater model, in order to examine the specific flow processes that are active in this environment. This research used samples and data provided by the Integrated Ocean Drilling Program (IODP) and the International Continental Scientific Drilling Program (ICDP).

The nappes of the Lepontine dome: the influence of tectonic inheritance on their deformation style

NASA Astrophysics Data System (ADS)

Schenker, Filippo Luca; Ambrosi, Christian; Scapozza, Cristian; Czerki, Dorota; Castelletti, Claudio; Maino, Matteo; Gouffon, Yves

2017-04-01

The Lepontine dome exposes the tectonostratigraphy of the Central Alps, from bottom-to-top, the subpenninic gneissic nappes of the Leventina, Simano, Adula/Cima-Lunga and Maggia. These units were part of a post-Variscan gneissic crust, which was intensely intruded by several generations of granitoids forming laccoliths and dikes of different shapes and sizes within paragneisses, augengneisses and amphibolites. During the Alpine orogenic cycle this initial and complex geological architecture was reshaped into a fold and thrust belt. We present the effect of these initial rheological anomalies along the Leventina, Simano and Adula/Cima-Lunga units through the geological map of the Osogna sheet (Swiss National Map no. 1293,1:25'000) together with structural and metamorphic data. The geological map shows that the Simano and Adula/Cima-Lunga units have an internal and lateral lithological variation at different scales as illustrated by the geological cross-sections. All lithologies present a penetrative amphibolite-facies foliation, which can vary in intensity among the rock-types. On the foliation plane a mineral and stretching lineation is visible dipping NW or SE, depending on the plane dip direction. The kinematic analysis indicates a top-to-the NW shearing. Despite this consistent structural data showing a regional dominant fabric, the folds (generally with a fold-axis parallel to the lineation) show different styles, depending on the thickness and the rock-type of the folded horizon and matrix, do not form laterally continuous structures and often are not cylindrical. As a consequence, such structures are interpreted as local perturbation rather than structures of regional importance. Furthermore, the Leventina and the Simano boundary is locally incongruent with the tectonic contact of the published maps. The amphibolite and paragneisses, used in the past as nappe divider, result to be deformed magmatic xenoliths. Therefore we present evidence (i) of a bottom-to-top top-to-the-foreland deformation gradient between the Leventina and Adula/Cima-Lunga units, (ii) within this shearing, the inherited rheological heterogeneities in the units lead to non-coaxial ductile deformation complicating the tectonic understanding and (iii) the boundary between the Leventina and the Simano units was a magmatic contact, questioning the allochthonous character of the Simano unit.

Kinderhookian (Lower Mississippian) calcareous rocks of the Howard Pass quadrangle, western Brooks Range: A section in Geologic studies in Alaska by the U.S. Geological Survey, 1995

USGS Publications Warehouse

Dumoulin, Julie A.; Harris, Anita G.

1997-01-01

Calcareous rocks of Kinderhookian (early Early Mississippian) age are widely distributed across the Howard Pass quadrangle in the western Brooks Range. Most occur in the lower part of the Lisburne Group (herein called the Rough Mountain Creek unit) and the upper part of the Endicott Group (Kayak Shale) in two sequences (Key Creek and Aniuk River) of the Endicott Mountains allochthon. Kinderhookian strata are also found in the Kelly River allochthon (Utukok Formation?) and in sections of uncertain stratigraphic affinity and structural level spatially associated with mafic volcanic rocks.Predominant Kinderhookian lithologies in the Lisburne Group are skeletal supportstone (rich in pelmatozoans, bryozoans, and brachiopods) and lesser spiculite; skeletal supportstone and calcarenite are the chief calcareous rock types in the Kayak Shale. Conodont and brachiopod faunas indicate that all of the Rough Mountain Creek unit and much of the Kayak Shale in the study area are of late Kinderhookian age. Lithologic and paleontologic data suggest that Kinderhookian strata in the Howard Pass quadrangle were deposited largely in inner- and middle-shelf settings with normal marine salinity and locally high energy. Overall, calcareous beds in the Rough Mountain Creek unit accumulated in a wider range of environments, less subject to siliciclastic input, than did calcareous beds in the Kayak, and Kinderhookian beds of both units in the Key Creek sequence formed in less diverse, somewhat shallower environments than correlative rocks in the Aniuk River sequence. Lithofacies patterns and contact relations imply that decreased siliciclastic influx, perhaps accompanied by relative sea-level rise, initiated deposition of the Rough Mountain Creek unit; relative sea-level rise and concurrent circulatory restriction most likely ended its deposition.Kinderhookian calcareous rocks in the Howard Pass quadrangle have several implications for middle Paleozoic paleogeography of the western Brooks Range. First, sequences of the Endicott Mountains allochthon that contain the Rough Mountain Creek unit contrast sharply with other sequences included in this allochthon that contain thicker and younger Carboniferous platform carbonate successions. These differences in stratigraphic succession suggest significant shortening within the Endicott Mountains allochthon. Second, Kinderhookian calcareous rocks in the Howard Pass quadrangle may have been a secondary source for carbonate turbidites of the Rim Butte unit (Ipnavik allochthon).

In-Situ Oxygen Isotopic Composition of Tagish Lake: An Ungrouped Type 2 Carbonaceous Chondrite

NASA Technical Reports Server (NTRS)

Zolensky, Michael E.; Engrand, Cecile; Gounelle, Matthieu; Zolensky, Mike E.

2001-01-01

We have measured the oxygen isotopic composition of several components of Tagish Lake by ion microprobe. This meteorite constitutes the best preserved sample of C2 matter presently available for study. It presents two different lithologies (carbonate-poor and -rich) which have fairly comparable oxygen isotopic composition, with regard to both the primary or secondary minerals. For the olivine and pyroxene grains, their delta O-18 values range from - 10.5% to + 7.4% in the carbonate-poor lithology, with a mean Delta O-17 value of - 3.7 2.4%. In the carbonate-rich lithology, delta O-18 varies from - 7.9% to + 3.3%, and the mean Delta O-17 value is - 4.7 +/- 1.4%. Olivine inclusions (Fo(sub >99)) with extreme O-16-enrichment were found in both lithologies: delta O-18 = - 46.1 %, delta O-187= - 48.3% and delta O-18 = - 40.6%, delta O-17 = - 41.2% in the carbonate-rich lithology; delta O-18 = - 41.5%, delta O-17 = -43.4%0 in the carbonate-poor lithology. Anhydrous minerals in the carbonate-poor lithology are slightly more O-16-rich than in the carbonate-rich one. Four low-iron manganese-rich (LIME) olivine grains do not have an oxygen isotopic composition distinct from the other "normal" olivines. The phyllosilicate matrix presents the same range of oxygen isotopic compositions in both lithologies: delta O-18 from approximately 11 % to approximately 6%, with an average Delta. O-17 approximately 0%. Because the bulk Tagish Lake oxygen isotopic composition given by Brown et al. is on the high end of our matrix analyses, we assume that this "bulk Tagish Lake" composition probably only represents that of the carbonate-rich lithology. Calcium carbonates have delta O-18 values up to 35%, with Delta O-17 approximately 0.5%0. Magnetite grains present very high Delta O-17 values approximately + 3.4%0 +/- 1.2%. Given our analytical uncertainties and our limited carbonate data, the matrix and the carbonate seem to have formed in isotopic equilibrium. In that case, their large isotopic fractionation would argue for a low temperature (CM-like, T approximately 0 deg) formation. Magnetite probably formed during a separate event. Tagish Lake magnetite data is surprisingly compatible with that of R-chondrites and unequilibrated ordinary (LL3) chondrites. Our oxygen isotope data strongly supports the hypothesis of a single precursor for both lithologies. Drastic mineralogical changes between the two lithologies not being accompanied with isotopic fractionation seem compatible with the alteration model presented by Young et aI. Tagish Lake probably represents the first well preserved large sample of the C2 matter that dominates interplanetary matter since the formation of the solar system.

AR-40 AR-39 Age of an Impact-Melt Lithology in DHOFAR 961

NASA Technical Reports Server (NTRS)

Frasl, B.; Cohen, B. A.; Li, Z.-H.; Jolliff, B.; Korotev, R.; Zeigler, R.

2016-01-01

The South Pole-Aitken (SPA) basin is the stratigraphically oldest identifiable lunar basin and is therefore one of the most important targets for absolute age-dating to help understand whether ancient lunar bombardment history smoothly declined or was punctuated by a cataclysm. The SPA basin also has another convenient property, a geochemically distinct interior, unobscured by extensive mare basalt fill. A case has been made for the possible origin of the Dhofar 961 lunar meteorite in the South Pole-Aitken (SPA) basin, based on comparing its composition with Lunar Prospector gamma-ray data for the interior of the SPA basin. Dhofar 961 contains several different impact-melt (IM) lithologies. Jolliff et al. described two classes of mafic impact-melt lithologies, one dominated by olivine (Lithology A) and the other by plagioclase (An 95-96.5) (Lithology B). Broad-beam analyses of these lithologies yielded (is) approximately 14.0 wt% FeO, 11.7 wt% MgO, and 15.4 wt% Al2O3. Lithologies A and B differ by approximately 2.5% Al2O3, 1.5% FeO and 1.5% MgO, consistent with the occurrence of olivine phenocrysts in A and plagioclase clasts in B. Both lithologies are considerably more mafic than the Apollo mafic impact-melt breccias, corresponding to olivine gabbronorite. Joy et al. used U-Pb dating to investigate phosphate fragments in the Dhofar 961 matrix and impact-melt clasts. Matrix phosphates have 4.34 to 4 Ga ages, consistent with ancient KREEP-driven magmatic episodes and Pre-Nectarian ((is) greater than 3.92 Ga). Phosphates found within Dhofar 961 crystalline impact melt breccia clasts range from 4.26 to 3.89 Ga, potentially recording events throughout the basin forming epoch of lunar history. The youngest reset ages in the Dhofar 961 sample represent an upper limit for the time of formation of the meteorite. Joy et al suggested this age represents the final impact that mixed and consolidated several generations of precursor rocks into the Dhofar meteorite group, although they note that further age dating of all the stones is required to test this hypothesis. We received a split of Dhofar 961 from R. Zeigler consisting of a large clast of IM Lithology B, with some light-colored, friable matrix clinging to the external margins of the impact-melt clast. This lithology was not present in the samples investigated by Joy et al. and thus does not have corresponding U-Pb ages on it. We created multiple subsplits of both the IM and matrix lithologies, each weighing several tens of micrograms. We conducted Ar-40 Ar-39 dating of this candidate SPA material by high-resolution step heating and comparing it with the regolith that surrounds it.

Regional analysis of tertiary volcanic Calderas (western U.S.) using Landsat Thematic Mapper imagery

NASA Technical Reports Server (NTRS)

Spatz, David M.; Taranik, James V.

1989-01-01

The Landsat Thematic Mapper (TM) imagery of the Basin and Range province of southern Nevada was analyzed to identify and map volcanic rock assemblages at three Tertiary calderas. It was found that the longer-wavelength visible and the NIR TM Bands 3, 5, and 7 provide more effective lithologic discrimination than the shorter-wavelength bands, due partly to deeper penetration of the longer-wavelength bands, resulting in more lithologically driven radiances. Shorter-wavelength TM Bands 1 and 2 are affected more by surficial weathering products including desert varnish which may or may not provide an indirect link to lithologic identity. Guidelines for lithologic analysis of volcanic terrains using Landsat TM imagery are outlined.

Source-to-Sink System Evolution as Recorded in Clastic Facies in Two New Zealand Examples: the Bounty System of South Island and the Waipaoa System of North Island

NASA Astrophysics Data System (ADS)

Marsaglia, K. M.

2010-12-01

New Zealand river sources and their submarine sinks are excellent examples for modeling source-to-sink systems. In particular, the sand fractions of these systems can be used as tracers to document links and/or disconnects between fluvial, shelf, slope, and bathyal components. Within any given system, the ability to use sand as a tracer depends on the nature of the rocks exposed in source river drainage basins. In evolving systems, the potential for erosional unroofing, change of outcrop lithology through time, can be important. Additionally, the ability of a given lithology to generate sediment of a certain size may also vary. For example in the New Zealand examples, Cenozoic mudstones generate mostly mud but can liberate recycled sand grains (if present), as well as a smaller proportion of mudstone lithic fragments depending on degree of mudstone induration; schist generates copious sand and quartz-vein pebbles; and thin-bedded sandy turbidites can generate significant gravel, as well as mud and sand. Sediment production mode also comes into play with glacial processes (South Island) generating rock flour, as well as coarser debris. The major outcropping unit across both islands is a sedimentary to metasedimentary forearc succession, the Torlesse Terrane. It served as the protolith of the Otago schist (South Island) and the source of detritus for Cretaceous and Cenozoic sedimentary units on both islands. Local magmatism also supplied sand-sized material: intraplate (South Island) volcanism produced intrabasinal epiclastic debris and magmatic arc (North Island) volcanism produced extrabasinal pyroclastic debris. Various lithologies have characteristic detrital signatures. For example, in the Cenozoic units of the Waipaoa system, Pliocene calcareous mudstone fragments are key lithic components in tracing sediment transport from source-to sink, whereas the major fingerprint of Otago schist input into the Bounty System of South Island is mica. Critical to defining sedimentary budgets in both New Zealand systems is defining the net proportion of dip-fed vs. strike-fed clastic components. The former are supplied directly to the system by coast-perpendicular rivers, and the latter are transported into or out of the system by coast-parallel currents (e.g., longshore, shelf, slope). Tectonic events in the fluvial drainage basin can also have major influences on the supply of sediment to offshore basins. There is evidence for lacustrine sediment traps in each New Zealand system and evidence, in at least one case, that they modified sediment input to the marine part of the system (Bounty Fan).

Geologic map of Yosemite National Park and vicinity, California

USGS Publications Warehouse

Huber, N.K.; Bateman, P.C.; Wahrhaftig, Clyde

1989-01-01

This digital map database represents the general distribution of bedrock and surficial deposits of the Yosemite National Park vicinity. It was produced directly from the file used to create the print version in 1989. The Yosemite National Park region is comprised of portions of 15 7.5 minute quadrangles. The original publication of the map in 1989 included the map, described map units and provided correlations, as well as a geologic summary and references, all on the same sheet. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:125,000 or smaller.

Aeromagnetic survey over U.S. to advance geomagnetic research

NASA Astrophysics Data System (ADS)

Hildenbrand, Thomas G.; Blakely, Richard J.; Hinze, William J.; Keller, G. Randy; Langel, Robert A.; Nabighian, Misac; Roest, Walter

A proposed high-altitude survey of the United States offers an exciting and cost effective opportunity to collect magnetic-anomaly data. Lockheed Martin Missile and Space Company is considering funding a reimbursable ER-2 aircraft (Figure 1) mission to collect synthetic aperture radar (SAR) imagery at an altitude of about 21 km over the conterminous United States and Alaska. The collection of total and vector magnetic field data would be a secondary objective of the flight. Through this “piggyback approach,” the geomagnetic community would inherit invaluable magnetic data at a nominal cost. These data would provide insight on fundamental tectonic and thermal processes and give a new view of the structural and lithologic framework of the crust and upper mantle.

Qualitatively Modeling solute fate and transport across scales in an agricultural catchment with diverse lithology

NASA Astrophysics Data System (ADS)

Wayman, C. R.; Russo, T. A.; Li, L.; Forsythe, B.; Hoagland, B.

2017-12-01

As part of the Susquehanna Shale Hills Critical Zone Observatory (SSHCZO) project, we have collected geochemical and hydrological data from several subcatchments and four monitoring sites on the main stem of Shaver's Creek, in Huntingon county, Pennsylvania. One subcatchment (0.43 km2) is under agricultural land use, and the monitoring locations on the larger Shaver's Creek (up to 163 km2) drain watersheds with 0 to 25% agricultural area. These two scales of investigation, coupled with advances made across the SSHCZO on multiple lithologies allow us to extrapolate from the subcatchment to the larger watershed. We use geochemical surface and groundwater data to estimate the solute and water transport regimes within the catchment, and to show how lithology and land use are major controls on ground and surface water quality. One area of investigation includes the transport of nutrients between interflow and regional groundwater, and how that connectivity may be reflected in local surface waters. Water and nutrient (Nitrogen) isotopes, will be used to better understand the relative contributions of local and regional groundwater and interflow fluxes into nearby streams. Following initial qualitative modeling, multiple hydrologic and nutrient transport models (e.g. SWAT and CYCLES/PIHM) will be evaluated from the subcatchment to large watershed scales. We will evaluate the ability to simulate the contributions of regional groundwater versus local groundwater, and also impacts of agricultural land management on surface water quality. Improving estimations of groundwater contributions to stream discharge will provide insight into how much agricultural development can impact stream quality and nutrient loading.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hohn, M.E.; Patchen, D.G.; Heald, M.

Non-uniform composition and permeability of a reservoir, commonly referred to as reservoir heterogeneity, is recognized as a major factor in the efficient recovery of oil during primary production and enhanced recovery operations. Heterogeneities are present at various scales and are caused by various factors, including folding and faulting, fractures, diagenesis and depositional environments. Thus, a reservoir consists of a complex flow system, or series of flow systems, dependent on lithology, sandstone genesis, and structural and thermal history. Ultimately, however, fundamental flow units are controlled by the distribution and type of depositional environments. Reservoir heterogeneity is difficult to measure and predict,more » especially in more complex reservoirs such as fluvial-deltaic sandstones. The Appalachian Oil and Natural Gas Research Consortium (AONGRC), a partnership of Appalachian basin state geological surveys in Kentucky, Ohio, Pennsylvania, and West Virginia, and West Virginia University, studied the Lower Mississippian Big Injun sandstone in West Virginia. The Big Injun research was multidisciplinary and designed to measure and map heterogeneity in existing fields and undrilled areas. The main goal was to develop an understanding of the reservoir sufficient to predict, in a given reservoir, optimum drilling locations versus high-risk locations for infill, outpost, or deeper-pool tests.« less

Experiment to evaluate feasibility of utilizing Skylab-EREP remote sensing data for tectonic analysis of the Bighorn Mountains region, Wyoming-Montana

NASA Technical Reports Server (NTRS)

Hoppin, R. A. (Principal Investigator)

1973-01-01

The author has identified the following significant results. Excellent imagery has been obtained from SL-3 along track 5 across the Bighorn Mountains and track 19 across the northern Black Hills. The red band is by far the best of the four black and white films of S-190A. Excellent detail is visible of topography, structure, resistant lithologies, and culture with good resolution obtainable at high magnification (30X). The infrared bands do not have as good resolution and are grainy at high magnification. They are of use as a complement to the red band particularly for relief enhancement in areas of heavy green grass and forest cover. S-190B high definition black and white is comparable to the red band (S-190A) in detail. Its main advantage is larger initial scale and slightly better resolution. High resolution color transparencies along track 19 allow detailed delineation of cultivated land and strip mining. A group of folds northwest of Billings stand out clearly. Light colored units in northwestern Black Hills and in the badlands can be mapped in great detail.

A regional groundwater-flow model for sustainable groundwater-resource management in the south Asian megacity of Dhaka, Bangladesh

NASA Astrophysics Data System (ADS)

Islam, Md Bayzidul; Firoz, A. B. M.; Foglia, Laura; Marandi, Andres; Khan, Abidur Rahman; Schüth, Christoph; Ribbe, Lars

2017-05-01

The water resources that supply most of the megacities in the world are under increased pressure because of land transformation, population growth, rapid urbanization, and climate-change impacts. Dhaka, in Bangladesh, is one of the largest of 22 growing megacities in the world, and it depends on mainly groundwater for all kinds of water needs. The regional groundwater-flow model MODFLOW-2005 was used to simulate the interaction between aquifers and rivers in steady-state and transient conditions during the period 1981-2013, to assess the impact of development and climate change on the regional groundwater resources. Detailed hydro-stratigraphic units are described according to 150 lithology logs, and a three-dimensional model of the upper 400 m of the Greater Dhaka area was constructed. The results explain how the total abstraction (2.9 million m3/d) in the Dhaka megacity, which has caused regional cones of depression, is balanced by recharge and induced river leakage. The simulated outcome shows the general trend of groundwater flow in the sedimentary Holocene aquifers under a variety of hydrogeological conditions, which will assist in the future development of a rational and sustainable management approach.

Structure, stratigraphy, and origin of Husband Hill, Columbia Hills, Gusev Crater, Mars

USGS Publications Warehouse

McCoy, T.J.; Sims, M.; Schmidt, M.E.; Edwards, L.; Tornabene, L.L.; Crumpler, L.S.; Cohen, B. A.; Soderblom, L.A.; Blaney, D.L.; Squyres, S. W.; Arvidson, R. E.; Rica, J.W.; Treguier, E.; d'Uston, C.; Grant, J. A.; McSween, H.Y.; Golombek, M.P.; Haldemann, A.F.C.; de Souza, P.A.

2008-01-01

The strike and dip of lithologic units imaged in stereo by the Spirit rover in the Columbia Hills using three-dimensional imaging software shows that measured dips (15-32??) for bedding on the main edifice of the Columbia Hill are steeper than local topography (???8-10??). Outcrops measured on West Spur are conformable in strike with shallower dips (7-15??) than observed on Husband Hill. Dips are consistent with observed strata draping the Columbia Hills. Initial uplift was likely related either to the formation of the Gusev Crater central peak or ring or through mutual interference of overlapping crater rims. Uplift was followed by subsequent draping by a series of impact and volcaniclastic materials that experienced temporally and spatially variable aqueous infiltration, cementation, and alteration episodically during or after deposition. West Spur likely represents a spatially isolated depositional event. Erosion by a variety of processes, including mass wasting, removed tens of meters of materials and formed the Tennessee Valley primarily after deposition. This was followed by eruption of the Adirondack-class plains basalt lava flows which embayed the Columbia Hills. Minor erosion, impact, and aeolian processes have subsequently modified the Columbia Hills. Copyright 2008 by the American Geophysical Union.

Opaque-rich lithology in the Divnoe achondrite: Petrology and origin

NASA Technical Reports Server (NTRS)

Petaev, M. I.

1993-01-01

An opaque-rich lithology (ORL) makes up to approximately 9 vol. percent of the Divnoe achondrite. It is characterized by enrichment of troilite and pyroxene, compared to the bulk Divnoe, and by the presence of tiny remnants of olivine in low-CA pyroxene and low minor element concentrations in pyroxene. The ORL was formed by local reaction between gaseous sulfur and olivine in the Divnoe. The Divnoe meteorite is an olivine-rich achondrite with subchondritic chemistry and mineralogy. It has a granoblastic coarse-grained olivine groundmass (CGL: coarse-grained lithology) with relatively large (2-10 mm) poikilitic patches (PP) of pyroxene and, rarely, plagioclase. The groundmass also contains an opaque-rich fine-grained lithology (ORL) which comprises approximately 9 vol. percent of the meteorite, displays reaction boundaries with the groundmass, and differs in mineral chemistry from it. Numerous micron- to mm-thick veins of troilite and, rarely, metal cross all the lithologies found in the meteorite. The Divnoe itself appears to represent a sample of an igneous source region.

Complex Formation History of Highly Evolved Basaltic Shergottite, Zagami

NASA Technical Reports Server (NTRS)

Niihara, T.; Misawa, K.; Mikouchi, T.; Nyquist, L. E.; Park, J.; Hirata, D.

2012-01-01

Zagami, a basaltic shergottite, contains several kinds of lithologies such as Normal Zagami consisting of Fine-grained (FG) and Coarse-grained (CG), Dark Mottled lithology (DML), and Olivine-rich late-stage melt pocket (DN). Treiman and Sutton concluded that Zagami (Normal Zagami) is a fractional crystallization product from a single magma. It has been suggested that there were two igneous stages (deep magma chamber and shallow magma chamber or surface lava flow) on the basis of chemical zoning features of pyroxenes which have homogeneous Mg-rich cores and FeO, CaO zoning at the rims. Nyquist et al. reported that FG has a different initial Sr isotopic ratio than CG and DML, and suggested the possibility of magma mixing on Mars. Here we report new results of petrology and mineralogy for DML and the Olivine-rich lithology (we do not use DN here), the most evolved lithology in this rock, to understand the relationship among lithologies and reveal Zagami s formation history

Mineralogical, Chemical, and Isotopic Heterogeneity in Zagami: Evidence for a Complex Petrogenesis

NASA Technical Reports Server (NTRS)

Nyquist, L. E.; Misawa, K.; Shih, C-Y.; Niihara, T.; Park, J.

2013-01-01

Textural variations in the shergottite Zagami were initially interpreted as evidence that it formed in a heterogeneous lava flow. Variations in initial Sr-87/Sr-86 ratios between a Coarse Grained (CG) and a Fine Grained (FG) lithology and evidence for more extensive fractionation of the Rb/Sr ratio in a Dark Mottled Lithology (DML) are consistent with such an interpretation. More recently, Niihara et al. and Misawa et al. have reported the mineralogy and Sr-isotopic systematics of an Olivine Rich Lithology (ORL) found in association with the coarse-grained DML lithology in the Kanagawa Zagami specimen [6,7]. Here we call this lithology DML(Ka) to maintain a distinction with DML(USNM) as studied. An Ar-Ar study by Park et al. of a late stage K-rich melt enriched in K2O to approx 7% and intruded into ORL yielded an Ar-Ar age of 202+/0 7 Ma. The present work extends the study of Kanagawa Zagami to Nd-isotopes.

Geometric description and analysis of metamorphic tectonites (Pelagonian Zone, Internal Hellenides, Northern Greece)

NASA Astrophysics Data System (ADS)

Diamantopoulos, A.

2009-04-01

An assortment of alpine and pre-Permian metamorphic tectonites, belonging to the Pelagonian Zone of the Internal Hellenides, are analyzed from Askion, Vernon and Vorras mountains. They in fact compose the Upper plate of the Western Macedonia core complex, overlying Late Tertiary high-P rocks through large-scale detachment fautls (Diamantopoulos et al. 2007). This work wants to determine the architecture and the kinematic path of rocks in a 3D assumption. Field analysis concludes: a) Meta-sedimentary lithologies and amphibolites, meta-igneous lithologies, granitoid mylonites composed of augen fieldspar gneisses, Permo-Triassic fossiliferous rocks, meta-carbonates of Triassic-Jurassic age, a Jurassic mélange including meta-sedimentary lithologies, serpentinites and carbonate tectonic blocks, Mesozoic Ophiolites, Cretaceous limestones and conglomerates as well as flysch sediments compose the architecture of the study area, b) Multiple high and low-angle cataclastic zones of intense non-coaxial strain separate distinct pre-Permian lithologies, alpine from pre-alpine rocks, Triassic-Jurassic rocks from Permo-Triassic rocks, Jurassic mélange from flysch sediments, Jurassic mélange from Triassic-Jurassic rocks, Cretaceous rocks from the Jurassic mélange, Cretaceous limestones from flysch lithologies and Cretaceous rocks from serpentinites, c) Geometric analysis and description of asymmetric structures found in fault cores, damage zones and in the footwall-related rocks showed a prominent kinematic direction towards WSW in low-T conditions affected all the rock lithologies, d) Multiple S- and L- shape fabric elements in the pre-Permian and Permo-Triassic rocks appear an intricate orientation, produced by intense non-coaxial syn-metamorphic deformation, e) Sheath and isoclinal folds oriented parallel to the L-shape fabric elements as well as a major S-shape fabric element, producing macroscopic fold-like structures compose the main syn-metamorphic fabric elements in the pre-alpine tectonites, f) Discrete and distributed strain along the former boundaries and within footwall- and hangingwall rocks is connoted to control the bulk kinematic path of the involved sequences, g) Field evaluation of the structural geology and the tectonics connote the conjugate character of the cataclastically-deformed boundaries, causing overprinting of the pre-existed ductile-related geometries, h) For the age of the inferred WSW kinematic direction of the involved rocks we believe that it is closely associated with the tectonic superimposition of the Pelagonian Zone onto the Olympos tectonic window during post-Late Eocene times. Miocene to Quaternary faulting activity in all the scales overprint the above Late Tertiary perturbation, resulting a real complicated structural feature (Diamantopoulos 2006). Diamantopoulos A., 2006. Plio-Quaternary geometry and Kinematics of Ptolemais basin (Northern Greece). Implications for the intra-plate tectonics in Western Macedonia. Geologica Croatica 59/1, pages 85-96. Diamantopoulos A., Krohe A., Mposkos E., 2007. Structural asymmetry and distributed strain of low-T shear planes inducing evidence for orogen-scale kinematic partitioning during denudation of high-P rocks (Pelagonian Zone, Greece). Geophysical Research Abstracts, Vol. 9, 03622.

A Hydrostratigraphic System for Modeling Groundwater Flow and Radionuclide Migration at the Corrective Action Unit Scale, Nevada Test Site and Surrounding Areas, Clark, Lincoln, and Nye Counties, Nevada

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prothro, Lance; Drellack Jr., Sigmund; Mercadante, Jennifer

2009-01-31

Underground Test Area (UGTA) corrective action unit (CAU) groundwater flow and contaminant transport models of the Nevada Test Site (NTS) and vicinity are built upon hydrostratigraphic framework models (HFMs) that utilize the hydrostratigraphic unit (HSU) as the fundamental modeling component. The delineation and three-dimensional (3-D) modeling of HSUs within the highly complex geologic terrain that is the NTS requires a hydrostratigraphic system that is internally consistent, yet flexible enough to account for overlapping model areas, varied geologic terrain, and the development of multiple alternative HFMs. The UGTA CAU-scale hydrostratigraphic system builds on more than 50 years of geologic and hydrologicmore » work in the NTS region. It includes 76 HSUs developed from nearly 300 stratigraphic units that span more than 570 million years of geologic time, and includes rock units as diverse as marine carbonate and siliciclastic rocks, granitic intrusives, rhyolitic lavas and ash-flow tuffs, and alluvial valley-fill deposits. The UGTA CAU-scale hydrostratigraphic system uses a geology-based approach and two-level classification scheme. The first, or lowest, level of the hydrostratigraphic system is the hydrogeologic unit (HGU). Rocks in a model area are first classified as one of ten HGUs based on the rock’s ability to transmit groundwater (i.e., nature of their porosity and permeability), which at the NTS is mainly a function of the rock’s primary lithology, type and degree of postdepositional alteration, and propensity to fracture. The second, or highest, level within the UGTA CAU-scale hydrostratigraphic system is the HSU, which is the fundamental mapping/modeling unit within UGTA CAU-scale HFMs. HSUs are 3-D bodies that are represented in the finite element mesh for the UGTA groundwater modeling process. HSUs are defined systematically by stratigraphically organizing HGUs of similar character into larger HSUs designations. The careful integration of stratigraphic information in the development of HSUs is important to assure individual HSUs are internally consistent, correlatable, and mappable throughout all the model areas.« less

Possible petrogenetic associations among igneous components in North Massif soils: Evidence in 2-4 mm soil particles from 76503

NASA Technical Reports Server (NTRS)

Jolliff, Bradley L.; Bishop, Kaylynn M.; Haskin, Larry A.

1992-01-01

Studies of Apollo 17 highland igneous rocks and clasts in breccias from the North and South Massifs have described magnesian troctolite, norite, anorthositic gabbro, dunite, spinel cataclasites, and granulitic lithologies that may have noritic anothosite or anorthositic norite/gabbro as igneous precursors, and have speculated on possible petrogenetic relationships among these rock types. Mineral compositions and relative proportions of plagioclase and plagioclase-olivine particles in samples 76503 indicate that the precursor lithology of those particles were troctolitic anorthosite, not troctolite. Mineral and chemical compositions of more pyroxene-rich, magnesian breccias and granulites in 76503 indicate that their precursor lithology was anorthositic norite/gabbro. The combination of mineral compositions and whole-rock trace-element compositional trends supports a genetic relationship among these two groups as would result from differentiation of a single pluton. Although highland igneous lithologies in Apollo 17 materials have been described previously, the proportions of different igneous lithologies present in the massifs, their frequency of association, and how they are related are not well known. We consider the proportions of, and associations among, the igneous lithologies found in a North Massif soil, which may represent those of the North Massif or a major part of it.

Lithologic Effects on Landscape Response to Base Level Changes: A Modeling Study in the Context of the Eastern Jura Mountains, Switzerland

NASA Astrophysics Data System (ADS)

Yanites, Brian J.; Becker, Jens K.; Madritsch, Herfried; Schnellmann, Michael; Ehlers, Todd A.

2017-11-01

Landscape evolution is a product of the forces that drive geomorphic processes (e.g., tectonics and climate) and the resistance to those processes. The underlying lithology and structural setting in many landscapes set the resistance to erosion. This study uses a modified version of the Channel-Hillslope Integrated Landscape Development (CHILD) landscape evolution model to determine the effect of a spatially and temporally changing erodibility in a terrain with a complex base level history. Specifically, our focus is to quantify how the effects of variable lithology influence transient base level signals. We set up a series of numerical landscape evolution models with increasing levels of complexity based on the lithologic variability and base level history of the Jura Mountains of northern Switzerland. The models are consistent with lithology (and therewith erodibility) playing an important role in the transient evolution of the landscape. The results show that the erosion rate history at a location depends on the rock uplift and base level history, the range of erodibilities of the different lithologies, and the history of the surface geology downstream from the analyzed location. Near the model boundary, the history of erosion is dominated by the base level history. The transient wave of incision, however, is quite variable in the different model runs and depends on the geometric structure of lithology used. It is thus important to constrain the spatiotemporal erodibility patterns downstream of any given point of interest to understand the evolution of a landscape subject to variable base level in a quantitative framework.

A preliminary bioavailable strontium isotope soil map of Europe.

NASA Astrophysics Data System (ADS)

Hoogewerff, Jurian; Reimann, Clemens; Ueckermann, Henriette; Frei, Robert; Frei, Karin; van Aswegen, Thalita; Stirling, Claudine; Reid, Malcolm; Clayton, Aaron; Gemas Project Team

2017-04-01

The GEMAS project collected samples from grazing land (n=2118, 0-20cm depth) and agricultural soil (n=2211, 0-10cm depth) at a scale of 1 site/2500km2 in most of Europe1. Elemental analysis using different extractions (Aqua Regia and MMI), whole soil XRF data and Q-ICPMS lead isotope data have been published1. Here we report high-precision 87Sr/86Sr results for the first 1000+ samples. To best represent Sr in plants and animals an ammonium nitrate soil extraction was chosen2. Samples were measured in three laboratories and shared QC samples demonstrated the robustness of the complete extraction and measurement protocol. Observed 87Sr/86Sr values range from 0.7038 to 0.7597 with the majority of samples centring about the median of 0.7092. Spatial interpolation of the data shows some major trends over Europe with high 87Sr/86Sr in known old intrusive terrains in Scandinavia, Iberia and the Alps. To improve the spatial resolution we investigated relations between measured 87Sr/86Sr values and other parameters for which higher spatial density (interpolated) data exists in geological and lithological databases like IGME50003 and GLiM4. For each sampling site matching geological age data and lithology were obtained by overlaying sampling locations on the IGME5000 and GLiM maps and extracting age and lithology information. All statistical and geospatial manipulations were performed using the R statistical package. Overall the 87Sr/86Sr values show a moderate correlation (Pearson R=0.54) with age but demonstrate varying homogeneity in different lithological units. Within the GEMAS dataset the strontium isotope ratios correlate most strongly with the lead isotope results,206Pb/208Pb (R=0.56) indicating a combined age and "crustalinity" effect. Whole soil Rb (XRF) is slightly higher correlated (R=0.26) with 87Sr/86Sr than extracted Rb (AR) at R=0.12 indicating some influence of the long term Rb signal in the soil parent material. Sodium is the highest correlated whole soil (XRF) element (R=0.33), which initially might hint at the influence of seaspray as it is often hypothesized that seaspray is a major source of 87Sr/86Sr variation in coastal regions. To test this hypothesis the distances to the coast in the major north-westerly wind direction in Europe and the shortest distance to any coast were calculated. Neither distance measure provided any significant correlation with 87Sr/86Sr values, indicating that the cause of the Na-Sr correlation is not likely to be seaspray, which would agree with poor correlation with presumably mobile Na in the Aqua Regia extracts. In concordance with observations of other authors5 modeling accuracy is improved by creating separate models for contrasting lithologies; igneous, marine limestones and other types. Igneous parent material provided the most convincing model using parameters like age, Rb/Sr ratio and 206Pb/208Pb. Attempts to model 87Sr/86Sr of soil on marine limestones with the LOWESS version 36 87Sr/86Sr vs. age curve were not convincing although some pattern similarity could be observed. Uranium and sodium content combined with pH are reasonable predictors of 87Sr/86Sr in soils on marine limestone parent material. The 87Sr/86Sr dataset with coordinates and models will be available from the main author after publication later in 2017. Reimann, C., et al., (2014). Geologisches Jahrbuch (Reihe B 102), Schweizerbarth, Hannover. Voerkelius S. et al., (2010). Food Chemistry. 118 (4), pp. 933-940. Asch, K., (2003). Geologisches Jahrbuch, SA 3, Schweizerbarth. Hannover. Hartmann, J., and N. Moosdorf (2012), Geochem. Geophys. Geosyst., 13, Q12004. Bataille, C. P. and G. J. Bowen. 2012. Chemical Geology 304-305:39- 52. J. M. McArthur, et al., Journal of Geology, 2001, volume 109, p. 155-170

Pliocene episodic exhumation and the significance of the Munsiari thrust in the northwestern Himalaya

NASA Astrophysics Data System (ADS)

Stübner, Konstanze; Grujic, Djordje; Dunkl, István; Thiede, Rasmus; Eugster, Patricia

2018-01-01

The Himalayan thrust belt comprises three in-sequence foreland-propagating orogen-scale faults, the Main Central thrust, the Main Boundary thrust, and the Main Frontal thrust. Recently, the Munsiari-Ramgarh-Shumar thrust system has been recognized as an additional, potentially orogen-scale shear zone in the proximal footwall of the Main Central thrust. The timing of the Munsiari, Ramgarh, and Shumar thrusts and their role in Himalayan tectonics are disputed. We present 31 new zircon (U-Th)/He ages from a profile across the central Himachal Himalaya in the Beas River area. Within a ∼40 km wide belt northeast of the Kullu-Larji-Rampur window, ages ranging from 2.4 ± 0.4 Ma to 5.4 ± 0.9 Ma constrain a distinct episode of rapid Pliocene to Present exhumation; north and south of this belt, zircon (U-Th)/He ages are older (7.0 ± 0.7 Ma to 42.2 ± 2.1 Ma). We attribute the Pliocene rapid exhumation episode to basal accretion to the Himalayan thrust belt and duplex formation in the Lesser Himalayan sequence including initiation of the Munsiari thrust. Pecube thermokinematic modelling suggests exhumation rates of ∼2-3 mm/yr from 4-7 to 0 Ma above the duplex contrasting with lower (<0.3 mm/yr) middle-late Miocene exhumation rates. The Munsiari thrust terminates laterally in central Himachal Pradesh. In the NW Indian Himalaya, the Main Central thrust zone comprises the sheared basal sections of the Greater Himalayan sequence and the mylonitic 'Bajaura nappe' of Lesser Himalayan affinity. We correlate the Bajaura unit with the Ramgarh thrust sheet in Nepal based on similar lithologies and the middle Miocene age of deformation. The Munsiari thrust in the central Himachal Himalaya is several Myr younger than deformation in the Bajaura and Ramgarh thrust sheets. Our results illustrate the complex and segmented nature of the Munsiari-Ramgarh-Shumar thrust system.

Investigation of the structure and lithology of bedrock concealed by basin fill, using ground-based magnetic-field-profile data acquired in the San Rafael Basin, southeastern Arizona

USGS Publications Warehouse

Bultman, Mark W.

2013-01-01

Data on the Earth’s total-intensity magnetic field acquired near ground level and at measurement intervals as small as 1 m include information on the spatial distribution of nearsurface magnetic dipoles that in many cases are unique to a specific lithology. Such spatial information is expressed in the texture (physical appearance or characteristics) of the data at scales of hundreds of meters to kilometers. These magnetic textures are characterized by several descriptive statistics, their power spectrum, and their multifractal spectrum. On the basis of a graphical comparison and textural characterization, ground-based magnetic-field profile data can be used to estimate bedrock lithology concealed by as much as 100 m of basin fill in some cases, information that is especially important in assessing and exploring for concealed mineral deposits. I demonstrate that multifractal spectra of ground-based magnetic-field-profile data can be used to differentiate exposed lithologies and that the shape and position of the multifractal spectrum of the ground-based magnetic-field-profile of concealed lithologies can be matched to the upward-continued multifractal spectrum of an exposed lithology to help distinguish the concealed lithology. In addition, ground-based magnetic-field-profile data also detect minute differences in the magnetic susceptibility of rocks over small horizontal and vertical distances and so can be used for precise modeling of bedrock geometry and structure, even when that bedrock is concealed by 100 m or more of nonmagnetic basin fill. Such data contain valuable geologic information on the bedrock concealed by basin fill that may not be so visible in aeromagnetic data, including areas of hydrothermal alteration, faults, and other bedrock structures. Interpretation of these data in the San Rafael Basin, southeastern Arizona, has yielded results for estimating concealed lithologies, concealed structural geology, and a concealed potential mineral-resource target.

Lithology identification of aquifers from geophysical well logs and fuzzy logic analysis: Shui-Lin Area, Taiwan

NASA Astrophysics Data System (ADS)

Hsieh, Bieng-Zih; Lewis, Charles; Lin, Zsay-Shing

2005-04-01

The purpose of this study is to construct a fuzzy lithology system from well logs to identify formation lithology of a groundwater aquifer system in order to better apply conventional well logging interpretation in hydro-geologic studies because well log responses of aquifers are sometimes different from those of conventional oil and gas reservoirs. The input variables for this system are the gamma-ray log reading, the separation between the spherically focused resistivity and the deep very-enhanced resistivity curves, and the borehole compensated sonic log reading. The output variable is groundwater formation lithology. All linguistic variables are based on five linguistic terms with a trapezoidal membership function. In this study, 50 data sets are clustered into 40 training sets and 10 testing sets for constructing the fuzzy lithology system and validating the ability of system prediction, respectively. The rule-based database containing 12 fuzzy lithology rules is developed from the training data sets, and the rule strength is weighted. A Madani inference system and the bisector of area defuzzification method are used for fuzzy inference and defuzzification. The success of training performance and the prediction ability were both 90%, with the calculated correlation of training and testing equal to 0.925 and 0.928, respectively. Well logs and core data from a clastic aquifer (depths 100-198 m) in the Shui-Lin area of west-central Taiwan are used for testing the system's construction. Comparison of results from core analysis, well logging and the fuzzy lithology system indicates that even though the well logging method can easily define a permeable sand formation, distinguishing between silts and sands and determining grain size variation in sands is more subjective. These shortcomings can be improved by a fuzzy lithology system that is able to yield more objective decisions than some conventional methods of log interpretation.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barber, A.J.; Tjokrosapoetro, S.; Charlton, T.R.

In Timor, eastern Indonesia, where the northern margin of the Australian continent is colliding with the Banda Arc, Australian continental margin sediments are being incorporated into an imbricate wedge, which passes northward into a foreland fold and thrust belt. Field mapping in Timor has shown that scale clays, containing irregularly shaped or phacoidal blocks (up to several meters long) and composed of a wide range of lithologies derived from local stratigraphic units, occur in three environments: along wrench faults, as crosscutting shale diapirs, and associated with mud volcanoes. A model is proposed linking these phenomena. Shales become overpressured as amore » result of overthrusting; this overpressure is released along vertical wrench faults, which cut through the overthrust units; overpressured shales containing blocks of consolidated units rise along the fault zones as shale diapirs; and escaping water, oil, and gas construct mud volcanoes at the surface. 6 figures, 1 table.« less

Quantitative characterization and modeling of lithologic heterogeneity

NASA Astrophysics Data System (ADS)

Deshpande, Anil

The fundamental goal of this thesis is to gain a better understanding of the vertical and lateral stratigraphic heterogeneities in sedimentary deposits. Two approaches are taken: Statistical characterization of lithologic variation recorded by geophysical data such as reflection seismic and wireline logs, and stochastic forward modeling of sediment accumulation in basins. Analysis of reflection seismic and wireline log data from Pleistocene fluvial and deltaic deposits in the Eugene Island 330 field, offshore Gulf of Mexico reveal scale-invariant statistics and strong anisotropy in rock properties. Systematic quantification of lateral lithologic heterogeneity within a stratigraphic framework, using reflection seismic data, indicates that fluvial and deltaic depositional systems exhibit statistical behavior related to stratigraphic fabric. Well log and seismic data profiles show a decay in power spectra with wavenumber, k, according to ksp{-beta} with beta between 1 and 2.3. The question of how surface processes are recorded in bed thickness distributions as a function of basin accommodation space is addressed with stochastic sedimentation model. In zones of high accommodation, random, uncorrelated, driving events produce a range of spatially correlated lithology fields. In zones of low accommodation, bed thickness distributions deviate from the random forcing imposed (an exponential thickness distribution). Model results are similar to that of a shallowing upward parasequence recorded in 15 meters of offshore Gulf of Mexico Pleistocene core. These data record a deviation from exponentially distributed bed thicknesses from the deeper water part of the cycle to the shallow part of the cycle where bed amalgamation dominates. Finally, a stochastic basin-fill model is used to explore the primary controls on stratigraphic architecture of turbidite channel-fill in the South Timbalier 295 field, offshore Louisiana Gulf Coast. Spatial and temporal changes in topography and subsidence rate are shown to be the main controls on turbidite channel stacking pattern within this basin. The model predicts the deposition of thick, amalgamated turbidite channel sands in the basin during a period of high initial subsidence followed by deposition of thinner, less connected sands when basin subsidence rate and accommodation space are low.

Age Distribution of Lunar Impact-Melt Rocks in Apollo Drive-Tube 68001/2

NASA Technical Reports Server (NTRS)

Curran, N. M.; Bower, D. M.; Frasl, B.; Cohen, B. A.

2018-01-01

Apollo 16 double-drive tube 68001 /68002 provides impact and volcanic materials along a depth of approximately 60 cm in five compositional distinct units. 68001 /2 offers the potential to study distinct populations of impact melts with depth to understand how 'gardening' affects these samples. We will use unbiased major-element chemistry, mineralogy, and age to understand the impact history of Apollo 16 landing site. The study demonstrates the techniques that landed missions require to identify lithologies of interest (e.g., impact melts).

Regulatory Guidance for Permeable Reactive Barriers Designed to Remediate Chlorinated Solvents

DTIC Science & Technology

1999-12-01

Polyethylene 4ºC 48h Alkalinity 310.1 100mL Polyethylene 4ºC 14d Other TDS 160.2 100 mL Glass, Plastic 4ºC 7d TSS 160.1 100 mL Glass, Plastic 4ºC 7d TOC 415.1...Resource Conservation and Recovery Act SO4 sulfate TBD to be determined TCE trichloroethene, trichloroethylene TDS total dissolved solids TOC total organic...Center ( DFC ) funnel-and-gate system. The aquifer at DFC consists of three lithologic units of decreasing permeability with depth: alluvium, weathered

Generalized thickness of the confining bed overlying the Floridan Aquifer, Southwest Florida Water Management District

USGS Publications Warehouse

Buono, Anthony; Spechler, R.M.; Barr, G.L.; Wolansky, R.M.

1979-01-01

This map presents the thickness of the confining bed overlying the Floridan aquifer in the Southwest Florida Water Management District and adjacent areas. The bed separates the surficial aquifer from the underlying Floridan aquifer. Lithologic logs and information from quarries were used in conjunction with an unpublished map to compile this map at 1:250,000 scale. Units included in the confining bed are: clay, sandy clay and marl, undifferentiated with respect to age, the Hawthorn Formation, and the unconsolidated sections of the Tampa Limestone. (Kosco-USGS)

Altitude, depth, and thickness of the Galena-Platteville Bedrock Unit in the subcrop area of Illinois and Wisconsin

USGS Publications Warehouse

Brown, Timothy A.; Dunning, Charles P.; Sharpe, Jennifer B.

2000-01-01

The report series will enable investigators involved in site-specific studies within the subcrop area to understand the regional geologic framework of the unit and to find additional reference sources. This report consists of four sheets that show the altitude (sheet 1), depth from land surface (sheet 2), total thickness (sheet 3), and location of altitude data (sheet 4) of the lithologic units that constitute the Galena-Platteville bedrock unit within the subcrop area. The sheets also show major known geologic features within the Galena-Platteville study area in Illinois and Wisconsin. A geographic information system (GIS) was used to generate data layers (coverages) from point data and from published and unpublished contour maps at various scales and detail. Standard GIS procedures were used to change the coverages into the maps shown on the sheets presented in this report. A list of references for the data used to prepare the maps is provided. 

Lithologic distribution and geologic history of the Apollo 17 site: The record in soils and small rock particles from the highland massifs

NASA Astrophysics Data System (ADS)

Jolliff, Bradley L.; Rockow, Kaylynn M.; Korotev, Randy L.; Haskin, Larry A.

1996-01-01

Through analysis by instrumental neutron activation (INAA) of 789 individual lithic fragments from the 2 mm-4 mm grain-size fractions of five Apollo 17 soil samples (72443, 72503, 73243, 76283, and 76503) and petrographic examination of a subset, we have determined the diversity and proportions of rock types recorded within soils from the highland massifs. The distribution of rock types at the site, as recorded by lithic fragments in the soils, is an alternative to the distribution inferred from the limited number of large rock samples. The compositions and proportions of 2 mm-4 mm fragments provide a bridge between compositions of <1 mm fines, and types and proportions of rocks observed in large collected breccias and their clasts. The 2 mm-4 mm fraction of soil from South Massif, represented by an unbiased set of lithic fragments from station-2 samples 72443 and 72503, consists of 71% noritic impact-melt breccia, 7% incompatible-trace-element-(ITE)-poor highland rock types (mainly granulitic breccias), 19% agglutinates and regolith breccias, 1% high-Ti mare basalt, and 2% others (very-low-Ti (VLT) basalt, monzogabbro breccia, and metal). In contrast, the 2 mm-4 mm fraction of a soil from the North Massif, represented by an unbiased set of lithic fragments from station-6 sample 76503, has a greater proportion of ITE-poor highland rock types and mare-basalt fragments: it consists of 29% ITE-poor highland rock types (mainly granulitic breccias and troctolitic anorthosite), 25% impact-melt breccia, 13% high-Ti mare basalt, 31% agglutinates and regolith breccias, 1% orange glass and related breccia, and 1% others. Based on a comparison of mass-weighted mean compositions of the lithic fragments with compositions of soil fines from all Apollo 17 highland stations, differences between the station-2 and station-6 samples are representative of differences between available samples from the two massifs. From the distribution of different rock types and their compositions, we conclude the following: (1) North-Massif and South-Massif soil samples differ significantly in types and proportions of ITE-poor highland components and ITE-rich impact-melt-breccia components. These differences reflect crudely layered massifs and known local geology. The greater percentage of impact-melt breccia in the South-Massif light-mantle soil stems from derivation of the light mantle from the top of the massif, which apparently is richer in noritic impact-melt breccia than are lower parts of the massifs. (2) At station 2, the 2 mm-4 mm grain-size fraction is enriched in impact-melt breccias compared to the <1 mm fraction, suggesting that the <1 mm fraction within the light mantle has a greater proportion of lithologies such as granulitic breccias which are more prevalent lower in the massifs and which we infer to be older (pre-basin) highland components. (3) Soil from station 6, North Massif, contains magnesian troctolitic anorthosite, which is a component that is rare in station-2 South-Massif soils. (4) Compositional differences between poikilitic impact-melt breccias from the two massifs suggest broad-scale heterogeneity in impact-melt breccia interpreted by most investigators to be ejecta from the Serenitatis basin. We have found rock types not previously recognized or uncommon at the Apollo 17 site. These include (1) ITE-rich impact-melt breccias that are compositionally distinct from previously recognized "aphanitic" and "poikilitic" groups at Apollo 17; (2) regolith breccias that are free of mare components and poor in impact melt of the types associated with the main melt-breccia groups, and that, if those groups derive from the Serenitatis impact, may represent the pre-Serenitatis surface; (3) several VLT basalts, including an unusual very-high-K basaltic breccia; (4) orange-glass regolith breccias; (5) aphanitic-matrix melt breccias at station 6; (6) fragments of alkali-rich composition, including alkali anorthosite, and monzogabbro; (7) one fragment of 72275-type KREEP basalt from station 3; (8) seven lithic fragments of ferroan-anorthositic-suite rocks; and (9) a fragment of metal, possibly from an L chondrite. Some of these lithologies have been found only as lithic fragments in the soils and not among the large rock samples. In contrast, we have not found among the 2 mm-4 mm lithic fragments individual samples of certain lithologies that have been recognized as clasts in breccias (e.g., dunite and spinel troctolite). The diversity of lithologic information contained in the lithic fragments of these soils nearly equals that found among large rock samples, and most information bearing on petrographic relationships is maintained, even in such small samples. Given a small number of large samples for "petrologic ground truth," small lithic fragments contained in soil "scoop" samples can provide the basis for interpreting the diversity of rock types and their proportions in remotely sensed geologic units. They should be considered essential targets for future automated sample-analysis and sample-return missions.

The relationship of lithology and watershed characteristics to fine sediment deposition in streams of the Oregon coast range.

PubMed

Sable, K A; Wohl, E

2006-05-01

Lithology is one of many factors influencing the amount, grain size distribution, and location of fine sediment deposition on the bed of mountain stream channels. In the Oregon Coast Range, 18 pool-riffle stream reaches with similar slope and intact riparian area and relatively unaffected by logjams were surveyed for assessment of fine sediment deposition. Half of the streams were in watersheds underlain by relatively erodible sandstone. The other half were underlain by a more resistant basalt. Channel morphology, hydraulic variables, particle size, relative pool volume of fine sediment (V*), and wood characteristics were measured in the streams. A significantly higher amount of fine sediment was deposited in the sandstone channels than in the basalt channels, as indicated by V*. Grab samples of sediment from pools also were significantly finer grained in the sandstone channels. Geographic information systems (GIS) software was used to derive several variables that might correlate with fine sediment deposition. These variables were combined with those derived from field data to create multiple linear regression models to be used for further exploration of the type and relative influence of factors affecting fine sediment deposition. Lithology appeared to be significant in some of these models, but usually was not the primary driver. The results from these models indicate that V* at the reach scale is best explained by stream power per unit area and by the volume of wood perpendicular to the flow per channel area (R(2) = 0.46). Findings show that V* is best explained using only watershed scale variables, including negative correlations with relief ratio and basin precipitation index, and positive correlations with maximum slope and circularity.

Petrology and isotopic geochemistry of the Archaean basement lithologies near Gardiner, Montana

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guy, R.E.; Sinha, A.K.

1985-01-01

In an attempt to recognize potential source rocks for some of the rhyolites of the Yellowstone Rhyolite Plateau, four major exposures of Precambrian rocks have been analyzed for major and trace elements and isotopic composition. The terrain is characterized by granitic gneisses with subordinant mica schist, quartzite, amphibolite, and two-mica granite. The gneiss units from the northern (Yankee Jim Canyon) and eastern (Lamar Canyon) outcrops are characterized by k-feldspar augen in a gneissic groundmass of two-feldspar--quartz--mica--epidote. The feldspar compositions are Or/sub 95/ and An/sub 5-15/ indicating metamorphic re-equilibration. Mafic phases are iron-rich with Fe:Mg of 1.0 in epidote, 0.7 inmore » pyroxene, and 0.5 in biotite. Sr isotopic analyses yield present day values of 0.7201-0.7519 for Lamar Canyon, 0.7157-0.7385 for Yankee Jam Canyon, and 0.7200-0.7679 for mica schist from the western and northern outcrops. Rb-Sr whole-rock data indicate a complicated isotopic history with ages ranging from 2800 to 3600 my. The 2800 my ages are consistent with ages for the Tobacco Root and Ruby Mountains to the NW (James and Hedge, 1980) and the Beartooth Range to the NE (Nunes and Tilton, 1971) while the 3600 my age may be related to the formation of the protolith. The rhyolites of the northern Yellowstone Rhyolite Plateau (Sr/sub I/=0.7100) cannot be derived from the exposed Archaean rocks based on Sr isotopic and whole-rock chemistry, and must be derived from lithologies not exposed in the area. This study shows that care must be taken when using surface lithologies to model potential sources materials for volcanic rocks in an associated terrain.« less

Field and petrological study of metasomatism and high-pressure carbonation from lawsonite eclogite-facies terrains, Alpine Corsica

NASA Astrophysics Data System (ADS)

Piccoli, Francesca; Vitale Brovarone, Alberto; Ague, Jay J.

2018-04-01

This study presents new field and petrological data on carbonated metasomatic rocks from the lawsonite-eclogite units of Alpine Corsica. These rocks form along major, slab-scale lithological boundaries of the subducted Alpine Tethys plate. Our results indicate that a large variety of rocks ranging from metamafic/ultramafic to metafelsic can react with carbon-bearing fluids, leading to carbon sequestration at high-pressure conditions. The process of carbonation includes both replacement of silicates by high-pressure carbonate, and carbonate veining. The field, microstructural and mineralogical data strongly suggest that the metasomatism was mediated by the infiltration of external fluids of mixed origin, including both mafic/ultramafic and metasedimentary sources. Our results support the following three-step evolution: (i) Release of aqueous fluids by lawsonite and/or antigorite breakdown at depth; (ii) Fluid channelization along the base of the metasedimentary pile of the subducted lithospheric plate and related reactive fluid flow leading to carbonate mineral dissolution; (iii) Further interactions of the resulting carbon-bearing fluids with slab-forming rocks at depths of ca. 70 km and carbonation of pre-existing silicate-rich lithologies. This study highlights the importance of carbonate-bearing fluids evolving along down-T, down-P paths, such as along slab-parallel lithological boundaries, for the sequestration of carbon in subduction zones, and suggests that similar processes may also operate in collisional settings. Fig. S2: Petrogenetic grid in the CaFMASH+CO2 system for the antigorite and clinopyroxene carbonation reactions, together with grossular forming reaction during decarbonation. Reactions are written with the high T assemblage to the right of the = sign.

Comparative study of Wenner and Schlumberger electrical resistivity method for groundwater investigation: a case study from Dhule district (M.S.), India

NASA Astrophysics Data System (ADS)

Vasantrao, Baride Mukund; Bhaskarrao, Patil Jitendra; Mukund, Baride Aarti; Baburao, Golekar Rushikesh; Narayan, Patil Sanjaykumar

2017-12-01

The area chosen for the present study is Dhule district, which belongs to the drought prone area of Maharashtra State, India. Dhule district suffers from water problem, and therefore, there is no extra water available to supply for the agricultural and industrial growth. To understand the lithological characters in terms of its hydro-geological conditions, it is necessary to understand the geology of the area. It is now established fact that the geophysical method gives a better information of subsurface geology. Geophysical electrical surveys with four electrodes configuration, i.e., Wenner and Schlumberger method, were carried out at the same selected sites to observe the similarity and compared both the applications in terms of its use and handling in the field. A total 54 VES soundings were carried out spread over the Dhule district and representing different lithological units. The VES curves are drawn using inverse slope method for Wenner configuration, IPI2 win Software, and curve matching techniques were used for Schlumberger configuration. Regionwise lithologs are prepared based on the obtained resistivity and thickness for Wenner method. Regionwise curves were prepared based on resistivity layers for Schlumberger method. Comparing the two methods, it is observed that Wenner and Schlumberger methods have merits or demerits. Considering merits and demerits from the field point of view, it is suggested that Wenner inverse slope method is more handy for calculation and interpretation, but requires lateral length which is a constrain. Similarly, Schlumberger method is easy in application but unwieldy for their interpretation. The work amply proves the applicability of geophysical techniques in the water resource evaluation procedure. This technique is found to be suitable for the areas with similar geological setup elsewhere.

ASTER, ALI and Hyperion sensors data for lithological mapping and ore minerals exploration.

PubMed

Beiranvand Pour, Amin; Hashim, Mazlan

2014-01-01

This paper provides a review of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), Advanced Land Imager (ALI), and Hyperion data and applications of the data as a tool for ore minerals exploration, lithological and structural mapping. Spectral information extraction from ASTER, ALI, and Hyperion data has great ability to assist geologists in all disciplines to map the distribution and detect the rock units exposed at the earth's surface. The near coincidence of Earth Observing System (EOS)/Terra and Earth Observing One (EO-1) platforms allows acquiring ASTER, ALI, and Hyperion imagery of the same ground areas, resulting accurate information for geological mapping applications especially in the reconnaissance stages of hydrothermal copper and gold exploration, chromite, magnetite, massive sulfide and uranium ore deposits, mineral components of soils and structural interpretation at both regional and district scales. Shortwave length infrared and thermal infrared bands of ASTER have sufficient spectral resolution to map fundamental absorptions of hydroxyl mineral groups and silica and carbonate minerals for regional mapping purposes. Ferric-iron bearing minerals can be discriminated using six unique wavelength bands of ALI spanning the visible and near infrared. Hyperion visible and near infrared bands (0.4 to 1.0 μm) and shortwave infrared bands (0.9 to 2.5 μm) allowed to produce image maps of iron oxide minerals, hydroxyl-bearing minerals, sulfates and carbonates in association with hydrothermal alteration assemblages, respectively. The techniques and achievements reviewed in the present paper can further introduce the efficacy of ASTER, ALI, and Hyperion data for future mineral and lithological mapping and exploration of the porphyry copper, epithermal gold, chromite, magnetite, massive sulfide and uranium ore deposits especially in arid and semi-arid territory.

Seamount subduction at seismogenic depths: structural and metamorphic evidence from the Zagros suture zone

NASA Astrophysics Data System (ADS)

Bonnet, G.; Agard, P.; Angiboust, S.; Fournier, M.; Omrani, J.

2017-12-01

Large-scale seafloor topographic features, such as seamounts, are for the most part subducted with the downgoing oceanic plate. They are expected to critically impact the seismogenic and mechanic behavior of subduction zones, but their exact role is strongly debated (i.e., as to whether they represent barriers to propagation or asperities promoting nucleation). Rare natural examples of metamorphosed seamounts, which got sliced off the slab along the plate interface and escaped recycling into the mantle, are therefore precious witnesses to document processes operating at depths of 0-30 km. We herein report the existence of a large-scale oceanic topographic structure sandwiched in the Zagros suture zone (Siah Kuh - SK - unit), most probably a former seamount, along with other blueschist units (Angiboust et al., EPSL 2016). The main criteria for identifying this seamount are its: (1) shape: the SK unit is a 1.5-2 km thick, rounded-shaped body with a 15-20 km diameter, (2) lithologies: it is made mainly of a regular succession of massive basaltic flows, commonly as pillow basalts, minor ophiolite-type gabbros and serpentinite, together with subordinate more differenciated volcanic and plutonic rocks. (3) sedimentary cover: basalts are overlain by shallowly deposited reef limestone and deepening-up sediments with the occurrence of cherts and pelagic limestones (which points to possible subsidence). Basalts have been analyzed for trace elements and have usually a N-MORB to OIB signature, which might be explained by its potential origin as a mid-oceanic ridge seamount. HP-LT minerals (lawsonite, aragonite, blue amphiboles) found across the whole structure, particularly in zones of localized compressive deformation, indicate that this seamount was shallowly subducted at 20 km. This deformation, interpreted to be syn-subduction, is assisted by a décollement rooting in serpentinite and/or oceanic metasediments and is associated with rare cataclase in magmatic rocks. We interpret these structures as related to the internal slicing of the seamount in subduction. The presence of these soft layers may prevent seismogenic deformation, since no pseudotachylites have been found.

Effects of land-use changes on landslides in a landslide-prone area (Ardesen, Rize, NE Turkey).

PubMed

Karsli, F; Atasoy, M; Yalcin, A; Reis, S; Demir, O; Gokceoglu, C

2009-09-01

Various natural hazards such as landslides, avalanches, floods and debris flows can result in enormous property damages and human casualties in Eastern Black Sea region of Turkey. Mountainous topographic character and high frequency of heavy rain are the main factors for landslide occurrence in Ardesen, Rize. For this reason, the main target of the present study is to evaluate the landslide hazards using a sequence of historical aerial photographs in Ardesen (Rize), Turkey, by Photogrammetry and Geographical Information System (GIS). Landslide locations in the study area were identified by interpretation of aerial photographs dated in 1973 and 2002, and by field surveys. In the study, the selected factors conditioning landslides are lithology, slope gradient, slope aspect, vegetation cover, land class, climate, rainfall and proximity to roads. These factors were considered as effective on the occurrence of landslides. The areas under landslide threat were analyzed and mapped considering the landslide conditioning factors. Some of the conditioning factors were investigated and estimated by employing visual interpretation of aerial photos and topographic data. The results showed that the slope, lithology, terrain roughness, proximity to roads, and the cover type played important roles on landslide occurrence. The results also showed that degree of landslides was affected by the number of houses constructed in the region. As a consequence, the method employed in the study provides important benefits for landslide hazard mitigation efforts, because a combination of both photogrammetric techniques and GIS is presented.

Using pebble lithology and roundness to interpret gravel provenance in piedmont fluvial systems of the Rocky Mountains, USA

USGS Publications Warehouse

Lindsey, D.A.; Langer, W.H.; Van Gosen, B. S.

2007-01-01

Clast populations in piedmont fluvial systems are products of complex histories that complicate provenance interpretation. Although pebble counts of lithology are widely used, the information provided by a pebble count has been filtered by a potentially large number of processes and circumstances. Counts of pebble lithology and roundness together offer more power than lithology alone for the interpretation of provenance. In this study we analyze pebble counts of lithology and roundness in two contrasting fluvial systems of Pleistocene age to see how provenance varies with drainage size. The two systems are 1) a group of small high-gradient incised streams that formed alluvial fans and terraces and 2) a piedmont river that formed terraces in response to climate-driven cycles of aggradation and incision. We first analyze the data from these systems within their geographic and geologic context. After this is done, we employ contingency table analysis to complete the interpretation of pebble provenance. Small tributary streams that drain rugged mountains on both sides of the Santa Cruz River, southeast Arizona, deposited gravel in fan and terrace deposits of Pleistocene age. Volcanic, plutonic and, to a lesser extent, sedimentary rocks are the predominant pebble lithologies. Large contrasts in gravel lithology are evident among adjacent fans. Subangular to subrounded pebbles predominate. Contingency table analysis shows that hard volcanic rocks tend to remain angular and, even though transport distances have been short, soft tuff and sedimentary rocks tend to become rounded. The Wind River, a major piedmont stream in Wyoming, drains rugged mountains surrounding the northwest part of the Wind River basin. Under the influence of climate change and glaciation during the Pleistocene, the river deposited an extensive series of terrace gravels. In contrast to Santa Cruz tributary gravel, most of the Wind River gravel is relatively homogenous in lithology and is rounded to well-rounded. Detailed analysis reveals a multitude of sources in the headwaters and the basin itself, but lithologies from these sources are combined downstream. Well-rounded volcanic and recycled quartzite clasts were derived from the headwaters. Precambrian igneous and metamorphic clasts were brought down tributary valleys to the Wind River by glaciers, and sandstone was added where the river enters the Wind River structural basin.

Differing response of soil microbial biomass phosphorus and phosphatase activities to lithology and climate in the Sierra Nevada of California

NASA Astrophysics Data System (ADS)

Margenot, A. J.; Wilson, S. G.

2016-12-01

Soil phosphorus (P) availability in ecosystems can be strongly reflected by microbial biomass P (MBP) and phosphatase activities. However, it is not known how MBP and phosphatases relate across variability in soil P engendered by parent material and climate. To evaluate this, we sampled surface soils (0-5 cm and 5-15 cm depth) at four climate zones (dominated by blue oak, ponderosa pine, white fir, and red fir, respectively) across three lithologies (granite, andesite, basalt) in the Sierra Nevada of California. This allowed for a unique study of both the influence of climate and lithology on microbial and enzymatic P dynamics. Soils were measured for MBP and potential activities of acid phosphomonoesterase (ACP), alkaline phosphomonoesterase (ALP), and phosphodiesterase (PDE), as well as available and organic P (Po). Across soils there were substantial differences in soil C (14-235 mg g-1), available P (0.6-111 µg g-1), and Po (53-1120 µg g-1), though soil pH was relatively constrained (pH 5.3-7.3). MBP responded more strongly to lithology than climate, and responded only to lithology at 5-15 cm depth. In contrast, phosphatase potential activities responded more strongly to climate than lithology, with greater response at 5-15 cm depth, and were positively correlated with soil C:Po (ACP p = 0.001, ALP and PDE p < 0.0001). MBP and phosphatase potential activities were not correlated, though both positively associated with soil C. Significant divergence of phosphatase activities in soils developed on andesite compared to granite and/or basalt in colder climates (white and red fir) did not reflect peak MBP at the rain-snow transition (ponderosa pine-white fir). PDE, but not ACP, ALP and MBP, was associated inversely with Po (p = 0.02) and tended to increase with available P (p = 0.059). Additionally, PDE varied most of measured indicators of P status across lithology and climate. The greater sensitivity of phosphatases to climate and of MBP to lithology, and the lack of association between MBP and phosphatase activities suggest that these (1) reflect different aspects of soil P status, and (2) are more responsive to soil C than soil P, which may explain observed trends across lithology and climate.

Examination of Multiple Lithologies Within the Primitive Ordinary Chondrite NWA 5717

NASA Technical Reports Server (NTRS)

Cato, M. J.; Simon, J. I.; Ross, D. K.; Morris, R. V.

2017-01-01

Northwest Africa 5717 is a primitive (subtype 3.05) ungrouped ordinary chondrite which contains two apparently distinct lithologies. In large cut meteorite slabs, the darker of these, lithology A, looks to host the second, much lighter in color, lithology B (upper left, Fig. 1). The nature of the boundary between the two is uncertain, ranging from abrupt to gradational and not always following particle boundaries. The distinction between the lithologies, beyond the obvious color differences, has been supported by a discrepancy in oxygen isotopes and an incongruity in the magnesium contents of chondrule olivine. Here, quantitative textural analysis and mineralogical methods have been used to investigate the two apparent lithologies within NWA 5717. Olivine grains contained in a thin section from NWA 7402, thought to be paired to 5717, were also measured to re-examine the distinct compositional range among the light and dark areas. Procedure: Particles from a high-resolution mosaic image of a roughly 13x15cm slice of NWA 5717 were traced in Adobe Photoshop. Due to the large size of the sample, visually representative regions of each lithology were chosen to be analyzed. The resulting layers of digitized particles were imported into ImageJ, which was used to measure their area, along with the axes, the angle from horizontal, and the centroid coordinates of ellipses fitted to each particle following the approach. Resulting 2D pixel areas were converted to spherical diameters employing the unfolding algorithm, which outputs a 3D particle size distribution based on digitized 2D size frequency data. Spatstat was used to create kernel density plots of the centroid coordinates for each region. X-ray compositional maps, microprobe analyses, and Mossbauer spectroscopy was conducted on a thin section of NWA 7402, tentatively paired to NWA 5717.

Late-Pleistocene evolution of the East Mediterranean shallow continental shelf of north-central Israel

NASA Astrophysics Data System (ADS)

Shtienberg, Gilad; Dix, Justin; Waldmann, Nicolas; Makovsky, Yizhaq; Bookman, Revital; Roskin, Joel; Bialik, Or; Golan, Arik; Sivan, Dorit

2016-04-01

Sea-level fluctuations are a dominant and dynamic mechanism that control coastal environmental through time. This is especially the case for the successive regressions and transgressions over the last interglacial cycle, which have shaped the deposition, preservation and erosion patterns of unconsolidated sediments currently submerged on continental shelves. The current study focuses on an integrated high-resolution marine and terrestrial litho-stratigraphic and geophysical framework of the north-central Mediterranean coastal zone of Israel. The interpretation enabled the reconstruction of the coastal evolution over the last ˜130 ka. A multi-disciplinary approach was applied by compiling existing elevation raster grids, bathymetric charts, detailed lithological borehole data-sets, a dense 110 km long sub-bottom geophysical survey and seven continuous boreholes sediment records. Based on seismic stratigraphic analysis, observed geometries, and reflective appearances, six bounding surfaces and seven seismic units were identified and characterized. Meanwhile, the chronostratigraphy of the terrestrial side was constructed through integration of magnetic susceptibility, sedimentological and geochemical analysis with 17 new OSL ages. The seismic units were correlated with the available terrestrial borehole data and then associated to the retrieved terrestrial chronostratigraphy to produce a 4D reconstruction model of the paleo-landscape. The entire unconsolidated sequence overlies a calcareous aeolianite (locally named Kurkar unit) dated from ˜131 - ˜104 ka, which represents the top of the last interglacial cycle dune sediments. The lower unconsolidated unit consists of a red silty loam dated to ˜71 ka. This Red-Paleosol unit is overlaid by a dark brown clayey silty loam This Brown-Paleosol unit dates to ˜58 - ˜36 ka and is overlaid by a dark silty clay wetland deposit dated to ˜21 - ˜10 ka. The wetland unit is topped by a quartz sand dated to ˜6.6 - 0.1 ka. This approach allowed us to investigate the relationship between the lithological units and sea-level change and thus enable the reconstruction of the coastal evolution over the last ˜130 ka. This reconstruction suggests that the stratigraphy is dominated by a sea level lowstand during which aeolian, fluvial and paleosol sediments were deposited in a terrestrial environment. The coastal-terrestrial landscape was flooded by the early to middle Holocene transgression. The results of this study provide a valuable framework for future national strategic shallow-water infrastructure construction and also for the possible locations of past human settlements in relation to coastal evolution through time.

Assessment of computer techniques for processing digital LANDSAT MSS data for lithological discrimination of Serra do Ramalho, State of Bahia

NASA Technical Reports Server (NTRS)

Paradella, W. R. (Principal Investigator); Vitorello, I.; Monteiro, M. D.

1984-01-01

Enhancement techniques and thematic classifications were applied to the metasediments of Bambui Super Group (Upper Proterozoic) in the Region of Serra do Ramalho, SW of the state of Bahia. Linear contrast stretch, band-ratios with contrast stretch, and color-composites allow lithological discriminations. The effects of human activities and of vegetation cover mask and limit, in several ways, the lithological discrimination with digital MSS data. Principal component images and color composite of linear contrast stretch of these products, show lithological discrimination through tonal gradations. This set of products allows the delineations of several metasedimentary sequences to a level superior to reconnaissance mapping. Supervised (maximum likelihood classifier) and nonsupervised (K-Means classifier) classification of the limestone sequence, host to fluorite mineralization show satisfactory results.

Producing landslide susceptibility maps by utilizing machine learning methods. The case of Finikas catchment basin, North Peloponnese, Greece.

NASA Astrophysics Data System (ADS)

Tsangaratos, Paraskevas; Ilia, Ioanna; Loupasakis, Constantinos; Papadakis, Michalis; Karimalis, Antonios

2017-04-01

The main objective of the present study was to apply two machine learning methods for the production of a landslide susceptibility map in the Finikas catchment basin, located in North Peloponnese, Greece and to compare their results. Specifically, Logistic Regression and Random Forest were utilized, based on a database of 40 sites classified into two categories, non-landslide and landslide areas that were separated into a training dataset (70% of the total data) and a validation dataset (remaining 30%). The identification of the areas was established by analyzing airborne imagery, extensive field investigation and the examination of previous research studies. Six landslide related variables were analyzed, namely: lithology, elevation, slope, aspect, distance to rivers and distance to faults. Within the Finikas catchment basin most of the reported landslides were located along the road network and within the residential complexes, classified as rotational and translational slides, and rockfalls, mainly caused due to the physical conditions and the general geotechnical behavior of the geological formation that cover the area. Each landslide susceptibility map was reclassified by applying the Geometric Interval classification technique into five classes, namely: very low susceptibility, low susceptibility, moderate susceptibility, high susceptibility, and very high susceptibility. The comparison and validation of the outcomes of each model were achieved using statistical evaluation measures, the receiving operating characteristic and the area under the success and predictive rate curves. The computation process was carried out using RStudio an integrated development environment for R language and ArcGIS 10.1 for compiling the data and producing the landslide susceptibility maps. From the outcomes of the Logistic Regression analysis it was induced that the highest b coefficient is allocated to lithology and slope, which was 2.8423 and 1.5841, respectively. From the estimation of the mean decrease in Gini coefficient performed during the application of Random Forest and the mean decrease in accuracy the most important variable is slope followed by lithology, aspect, elevation, distance from river network, and distance from faults, while the most used variables during the training phase were the variable aspect (21.45%), slope (20.53%) and lithology (19.84%). The outcomes of the analysis are consistent with previous studies concerning the area of research, which have indicated the high influence of lithology and slope in the manifestation of landslides. High percentage of landslide occurrence has been observed in Plio-Pleistocene sediments, flysch formations, and Cretaceous limestone. Also the presences of landslides have been associated with the degree of weathering and fragmentation, the orientation of the discontinuities surfaces and the intense morphological relief. The most accurate model was Random Forest which identified correctly 92.00% of the instances during the training phase, followed by the Logistic Regression 89.00%. The same pattern of accuracy was calculated during the validation phase, in which the Random Forest achieved a classification accuracy of 93.00%, while the Logistic Regression model achieved an accuracy of 91.00%. In conclusion, the outcomes of the study could be a useful cartographic product to local authorities and government agencies during the implementation of successful decision-making and land use planning strategies. Keywords: Landslide Susceptibility, Logistic Regression, Random Forest, GIS, Greece.

SHRIMP U-Pb detrital zircon dating to check subdivisions in metamorphic complexes: a case of study in the Nevado-Filábride complex (Betic Cordillera, Spain)

NASA Astrophysics Data System (ADS)

Santamaría-López, Ángel; Sanz de Galdeano, Carlos

2018-04-01

U-Pb dating on inherited detrital zircons has been applied to obtain the probable maximum age of deposition of the detrital protolith of the Nevado-Filábride complex (Betic Cordillera, Spain). Five of eight samples correspond to the lower part of the lithologic sequence of this complex, where radiometric dating of metasediments has not been presented till the present. The youngest age populations in the majority of samples are Carboniferous. The estimation of the maximum age of deposition in the lower and upper units is 349.1 ± 1.6 and 334.6 ± 2.9 Ma, respectively. In addition, samples show common age populations at ca. 490-630 and ca. 910-1010 Ma. Observations agree with the Carboniferous to early Permian U-Pb ages previously obtained in orthogneisses levels which are situated in the upper part of the complex. Combination of the minimum age of deposition deducible from the orthogneisses studies and the maximum ages of deposition obtained from the detrital zircons of this work, allow establishing the deposition of de studied lithological succession comprised between ca. 282 and 349 Ma or a shorter period.

An internally consistent pressure calibration of geobarometers applicable to the Earth’s upper mantle using in situ XRD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beyer, Christopher; Rosenthal, Anja; Myhill, Robert

We have performed an experimental cross calibration of a suite of mineral equilibria within mantle rock bulk compositions that are commonly used in geobarometry to determine the equilibration depths of upper mantle assemblages. Multiple barometers were compared simultaneously in experimental runs, where the pressure was determined using in-situ measurements of the unit cell volumes of MgO, NaCl, Re and h-BN between 3.6 and 10.4 GPa, and 1250 and 1500 °C. The experiments were performed in a large volume press (LVPs) in combination with synchrotron X-ray diffraction. Noble metal capsules drilled with multiple sample chambers were loaded with a range ofmore » bulk compositions representative of peridotite, eclogite and pyroxenite lithologies. By this approach, we simultaneously calibrated the geobarometers applicable to different mantle lithologies under identical and well determined pressure and temperature conditions. We identified discrepancies between the calculated and experimental pressures for which we propose simple linear or constant correction factors to some of the previously published barometric equations. As a result, we establish internally-consistent cross-calibrations for a number of garnet-orthopyroxene, garnet-clinopyroxene, Ca-Tschermaks-in-clinopyroxene and majorite geobarometers.« less

Delineating Heavy Metal Sources with Environmental Magnetism, X-Ray Fluorescence, and Geospatial Analysis: Baton Rouge, Louisiana

NASA Astrophysics Data System (ADS)

Taylor, Delmetria

The objective of this study is to detect the presence of anthropogenic magnetic particles by measuring the magnetic signature of soil samples in Baton Rouge, LA. Baton Rouge is currently ranked third among the Unites States' most polluted cities, so it is necessary to locate the sources of the problem and find solutions (U.S. Environmental Protection Agency [EPA], 2014). Magnetic susceptibility is a property that is easily, quickly, and inexpensively determined. It provides a highly-sensitive measurement of the compositional changes of minerals in soil. Magnetic susceptibility is influenced both anthropogenically and naturally by lithological and pedological heavy metal content. In this study, roughly 260 km2 (110 mi2) were sampled within the Baton Rouge, Louisiana area, and multiple environmental settings were covered. Geospatial and x-ray fluorescence analysis (XRF) were used to correlate magnetic susceptibility measurements and indicate increased anthropogenic activity near major industrial areas and interstates. Soil samples were analyzed, and isothermal remanent magnetization (IRM) acquisition curves indicate the presence of high- and low coercivity minerals, presumably magnetite and hematite. Enhanced susceptibility measurements do not appear to be dominated by lithology or soil in this particular area.

The ICDP Dead Sea deep drill cores: records of climate change and tectonics in the Levant

NASA Astrophysics Data System (ADS)

Goldstein, S. L.; Stein, M.; Ben-Avraham, Z.; Agnon, A.; Ariztegui, D.; Brauer, A.; Haug, G. H.; Ito, E.; Kitagawa, H.; Torfstein, A.

2012-12-01

The Dead Sea drainage basin sits at the boundary of the Mediterranean and the Saharan climate zones, and the basin is formed by the Dead Sea transform fault. The ICDP-funded Dead Sea Deep Drilling Project recovered the longest and most complete paleo-environmental and paleo-seismic record in the Middle East, drilling holes of ~450 and ~350 meters in deep (~300 m below the lake level) and shallow sites (~3 m), respectively, and. The sediments record the evolving environmental conditions (e.g. droughts, rains, floods, dust-storms), as well as tectonics (earthquake layers). The core can be dated using 14C on organic materials, U-Th on inorganic aragonite, stable isotopes, and layer counting. They were opened, described, and XRF-scanned during June to November 2011, the first sampling party took place in July 2012, and study is now underway. Some important conclusions can already be drawn. The stratigraphy reflects the climate conditions. During wet climate intervals the lithology is typically varve-like laminated aragonite and detritus (aad), reflecting summer and winter seasons, respectively, and sequences of mud. Gypsum layers reflect more arid climate, and salt (halite) indicates extreme aridity. The Dead Sea expands during glacials, and the portion of the core that corresponds to the last glacial Lisan Formation above the shoreline is easily recognized in the core based on the common lithological sequence, and this allows us to infer a broad scale age model. Interglacials show all the lithologic facies (aad, mud, gypsum, salt), reflecting extreme climate variability, while glacials contain the aad, mud, and gypsum but lack salt layers. Thus we estimate that the deep site hole extends into MIS 7 (to ~200,000 years). Thin (up to several cm thick) seismic layers occur throughout the core, but thick (up to several meters) landslide deposits only occur during glacial intervals. The most dramatic discovery is evidence of an extreme dry interval during MIS 5 at the deep site. There is a ~40 cm thick interval of partly rounded pebbles in the core at ~235 m below the lake floor. It is the only clean pebbly unit in the core, and resembles a beach deposit. Below the layer there is ~45 meters of mainly salt. These observations indicate a severe dry interval during MIS 5. This observation has implications for the Middle East today, where the Dead Sea level is dropping at rates >1m/year, as all the countries in the area are using all the runoff. GCM models indicate a more arid future in the region. The core shows that the runoff nearly stopped during the last interglacial without human intervention. Dating is underway to constrain the timing of the extreme drydown.

Ontological Encoding of GeoSciML and INSPIRE geological standard vocabularies and schemas: application to geological mapping

NASA Astrophysics Data System (ADS)

Lombardo, Vincenzo; Piana, Fabrizio; Mimmo, Dario; Fubelli, Giandomenico; Giardino, Marco

2016-04-01

Encoding of geologic knowledge in formal languages is an ambitious task, aiming at the interoperability and organic representation of geological data, and semantic characterization of geologic maps. Initiatives such as GeoScience Markup Language (last version is GeoSciML 4, 2015[1]) and INSPIRE "Data Specification on Geology" (an operative simplification of GeoSciML, last version is 3.0 rc3, 2013[2]), as well as the recent terminological shepherding of the Geoscience Terminology Working Group (GTWG[3]) have been promoting information exchange of the geologic knowledge. There have also been limited attempts to encode the knowledge in a machine-readable format, especially in the lithology domain (see e.g. the CGI_Lithology ontology[4]), but a comprehensive ontological model that connect the several knowledge sources is still lacking. This presentation concerns the "OntoGeonous" initiative, which aims at encoding the geologic knowledge, as expressed through the standard vocabularies, schemas and data models mentioned above, through a number of interlinked computational ontologies, based on the languages of the Semantic Web and the paradigm of Linked Open Data. The initiative proceeds in parallel with a concrete case study, concerning the setting up of a synthetic digital geological map of the Piemonte region (NW Italy), named "GEOPiemonteMap" (developed by the CNR Institute of Geosciences and Earth Resources, CNR IGG, Torino), where the description and classification of GeologicUnits has been supported by the modeling and implementation of the ontologies. We have devised a tripartite ontological model called OntoGeonous that consists of: 1) an ontology of the geologic features (in particular, GeologicUnit, GeomorphologicFeature, and GeologicStructure[5], modeled from the definitions and UML schemata of CGI vocabularies[6], GeoScienceML and INSPIRE, and aligned with the Planetary realm of NASA SWEET ontology[7]), 2) an ontology of the Earth materials (as defined by the SimpleLithology CGI vocabulary and aligned as a subclass of the Substance class in NASA SWEET ontology), and 3) an ontology of the MappedFeatures (as defined in the Representation sub-taxonomy of the NASA SWEET ontology). The latter correspond to the concrete elements of the map, with their geometry (polygons, lines) and geographical coordinates. The ontology model has been developed by taking into account applications primarily concerning the needs of geological mapping; nevertheless, the model is general enough to be applied to other contexts. In particular, we show how the automatic reasoning capabilities of the ontology system can be employed in tasks of unit definition and input filling of the map database and for supporting geologists in thematic re-classification of the map instances (e.g. for coloring tasks). ---------------------------------------- [1] http://www.geosciml.org [2] http://inspire.jrc.ec.europa.eu/documents/Data_Specifications/INSPIRE_DataSpecification_GE_v3.0rc3.pdf [3] http://www.cgi-iugs.org/tech_collaboration/geoscience_terminology_working_group.html [4] https://www.seegrid.csiro.au/subversion/CGI_CDTGVocabulary/trunk/OwlWork/CGI_Lithology.owl [5] We are currently neglecting the encoding of the geologic events, left as a future work. [6] http://resource.geosciml.org/vocabulary/cgi/201211/ [7] Web site: https://sweet.jpl.nasa.gov, Di Giuseppe et al., 2013, SWEET ontology coverage for earth system sciences, http://www.ics.uci.edu/~ndigiuse/Nicholas_DiGiuseppe/Research_files/digiuseppe14.pdf; S. Barahmand et al. 2009, A Survey on SWEET Ontologies and their Applications, http://www-scf.usc.edu/~taheriya/reports/csci586-report.pdf

Structural and Lithologic Characterization of the SAFOD Pilot Hole and Phase One Main Hole

NASA Astrophysics Data System (ADS)

Barton, D. C.; Bradbury, K.; Solum, J. G.; Evans, J. P.

2005-12-01

Petrological and microstructural analyses of drill cuttings were conducted for the San Andreas Fault Observatory at Depth (SAFOD) Pilot Hole and Main Hole projects. Grain mounts were produced at ~30 m (100 ft) intervals from drill cuttings collected from the Pilot Hole to a depth of 2164 m (7100 ft) and from Phase 1 of the SAFOD main hole to a depth of 3067 m (10062 ft). . Thin-section grain mount analysis included identification of mineral composition, alteration, and deformation within individual grains, measured at .5 mm increments on an equally spaced, 300 point grid pattern. Lithologic features in the Quaternary/Tertiary deposits from 30 - 640 m (100-2100 ft) in the Pilot Hole, and 670 - 792 m (2200 - 2600 ft) in the Phase 1 main hole, include fine-grained, thinly bedded sediments with clasts of fine-grained volcanic groundmass. Preliminary grain mount analysis from 1920 - 3067 m (6300 - 10062) in the Phase 1 main hole, indicates a sedimentary sequence consisting of fine-grained lithic fragments of very fine-grained shale. Deformation mechanisms observed within the cuttings of granitic rocks from 914 - 1860 m (3000 - 6100 ft.) include intracrystalline plasticity and cataclasis. Intracrystalline plastic deformation within quartz and feldspar grains is indicated by undulatory extinction, ribbon grains, chessboard patterns, and deformation twins and lamellae. Cataclastic deformation is characterized by intra- and intergranular microfractures, angular grains, gouge zones, iron-oxide banding, and comminution. Mineral and cataclasite abundances were plotted as a function of weight percent vs. depth. Plots of quartz and feldspar abundances are also correlated with XRD weight percent data from 1160 - 1890 m (3800 - 6200 ft.) in the granitic and granodioritic sequences of the Phase 1 main hole. Regions of the both of the drill holes with cataclasite abundances ranging from 20 - 30 wt% are interpreted as shear zones. Shear zones identified in this study from 1150 - 1420 m (3773 - 4659 ft.) in the Pilot Hole occur in the same location as shear zones recognized by Boness and Zoback (2004) using borehole geophysical data. These shear zones may possibly be correlated to shear zones identified in the Phase I main hole from 1615 - 2012 m (5300 - 6600 ft). If this is the case, it can be explained by steeply dipping subsidiary fault zones, likely associated with the San Andreas Fault system.

Field test results--a new logging tool for formation density and lithology measurements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Borai, A.M.; Muhsin, M.A.

1983-03-01

The formation porosity can be determined from borehole density measurements if the density of the rock is known. Generally, this is determined from the lithology. The Litho-Density Tool, LDT, provides an improved measurement of the formation density and a new measurement of lithology. Field tests of LDT proved that the tool could be run alone in a wide range of formations to provide porosity values comparable to those obtained by running a density log combined with a neutron log.

Sediment provenance in contractional orogens: The detrital zircon record from modern rivers in the Andean fold-thrust belt and foreland basin of western Argentina

NASA Astrophysics Data System (ADS)

Capaldi, Tomas N.; Horton, Brian K.; McKenzie, N. Ryan; Stockli, Daniel F.; Odlum, Margaret L.

2017-12-01

This study analyzes detrital zircon U-Pb age populations from Andean rivers to assess whether active synorogenic sedimentation accurately records proportional contributions from varied bedrock source units across different drainage areas. Samples of modern river sand were collected from west-central Argentina (28-33°S), where the Andes are characterized by active uplift and deposition in diverse contractional provinces, including (1) hinterland, (2) wedge-top, (3) proximal foreland, and (4) distal broken foreland basin settings. Potential controls on sediment provenance were evaluated by comparing river U-Pb age distributions with predicted age spectra generated by a sediment mixing model weighted by relative catchment exposure (outcrop) areas for different source units. Several statistical measures (similarity, likeness, and cross-correlation) are employed to compare how well the area-weighted model predicts modern river age populations. (1) Hinterland basin provenance is influenced by local relief generated along thrust-bounded ranges and high zircon fertility of exposed crystalline basement. (2) Wedge-top (piggyback) basin provenance is controlled by variable lithologic durability among thrust-belt bedrock sources and recycled basin sediments. (3) Proximal foreland (foredeep) basin provenance of rivers and fluvial megafans accurately reflect regional bedrock distributions, with limited effects of zircon fertility and lithologic durability in large (>20,000 km2) second-order drainage systems. (4) In distal broken segments of the foreland basin, regional provenance signatures from thrust-belt and hinterland areas are diluted by local contributions from foreland basement-cored uplifts.

Evaluating the competing effects of lithology and sediment supply on the erosional dynamics of rivers crossing active faults.

NASA Astrophysics Data System (ADS)

Whittaker, Alex; Boulton, Sarah; Kent, Emiko; Zondervan, Jesse; Hann, Madeleine; Watkins, Stephen; Bell, Rebecca; Brooke, Sam

2017-04-01

Lithology and sediment supply influence the erosional dynamics of rivers crossing active faults and together these effects govern the style, timescale and means by which landscapes respond to their tectono-climatic boundary conditions. Here, for transient bedrock catchments in the Gediz Graben, Turkey, and the Gulf of Corinth, Greece, for which the timing and rate of active faulting is known, we quantify the relative importance of rock strength and sediment supply on models of fluvial incision. We determine rock type, strength and erodibility using a Schmidt hammer and structural measurements of joint density and size. We evaluate the downstream distribution of channel width and stream power and calculate the extent to which the latter scales with tectonic rates and rock strength. Sediment supply is constrained using estimates of bedrock exposure, transport capacities and erosional fluxes. For the Turkish examples, stream powers in the metamorphic rocks are four times greater than in the Neogene sediment units, indicating a four-fold difference in bedrock erodibility, K, for a two-fold variation in in Schmidt hammer hardness. In the Gulf of Corinth examples, we interpret differences in stream powers near the active faults to represent order of magnitude differences in bedrock erodibility between carbonate and sandstone/conglomerate units. We also observe that in both cases, significant along-strike variation in fault slip rate is not associated with an increase in stream power for the sedimentary rocks and we assess the extent to which this stream power deficit may also represent the effects of sediment-flux-dependent incision.

Evidence for the importance of ductile shear in regional fabric development in Grenville-age gneisses of the Beaver Creek region, Northwest Lowlands, New York State

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tewksbury, B.; Culbertson, H.; Marcoline, J.

1993-03-01

In the Beaver Creek region of the Northwest Lowlands, Brown (1989) has described Grenville-age metasedimentary and metaigneous rocks as showing a prominent regional foliation, early southeastward emplacement of a nappe complex (the North Gouverneur Nappe), 2 subsequent generations of folds, and late regional faulting along the Beaver Creek, Pleasant Lake, and Hickory-Mud Lakes faults. The authors examined a variety of units across the Beaver Creek region, including a granitic augen gneiss immediately west of the Beaver Creek Fault Zone, an alaskitic gneiss immediately below Brown's (1989) North Gouverneur Nappe Sole Fault, a biotitic granitic gneiss within the body of Brown'smore » North Gouverneur Nappe, and hornblende augen gneisses and metasediments adjacent to the granitic gneisses. Each of the granitic units has moderately well-developed to extremely well-developed quartz ribbon lineations, and all show at least 2 ductile shear fabrics. Shear fabrics are present as well in the hornblende augen gneisses but are essentially absent in most of the metasedimentary lithologies, even those immediately adjacent to well-lineated, sheared granitic gneiss. The earliest shear fabrics exhibit spectacular quartz ribbon lineations, sigma grains, and, in the hornblende augen gneiss, shear bands. Granitic gneisses in the Beaver Creek Region show shear fabrics in addition to the main fabric in the rock. A second, variably-recovered shear fabric with quartz ribbons and well-developed sigma grains with core and mantle structure overprints the main shear fabric and shows largely the same sense of shear. The authors suggest further that a regional kinematic model for the Beaver Creek region must take into account significant, protracted regional shear, perhaps including formation of sheath folds, as in the Hyde School Gneiss at Payne Lake and Dobbs Creek.« less

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

40 CFR 146.22 - Construction requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Director may consider information on: (i) Nature of formation fluids; (ii) Lithology of injection and... underground sources of drinking water in areas where the lithology has not been determined: (A) Electric and...

High-resolution hydro- and geo-stratigraphy at Atlantic Coastal Plain drillhole CR-622 (Strat 8)

USGS Publications Warehouse

Wrege, B.M.; Isely, J.J.

2009-01-01

We interpret borehole geophysical logs in conjunction with lithology developed from continuous core to produce high-resolution hydro- and geo-stratigraphic profiles for the drillhole CR-622 (Strat 8) in the Atlantic Coastal Plain of North Carolina. The resulting hydrologic and stratigraphic columns show a generalized relation between hydrologic and geologic units. Fresh-water aquifers encountered are the surficial, Yorktown, Pungo River and Castle Hayne. Geologic units present are of the middle and upper Tertiary and Quaternary periods, these are the Castle Hayne (Eocene), Pungo River (Miocene), Yorktown (Pliocene), James City and Flanner Beach (Pleistocene), and the topsoil (Holocene). The River Bend Formation (Oligocene) is missing as a distinct unit between the Pungo River Formation and the Castle Hayne Formation. The confining unit underlying the Yorktown Aquifer corresponds to the Yorktown Geologic Unit. The remaining hydrologic units and geologic units are hydrologically transitional and non-coincident. The lower Pungo River Formation serves as the confining unit for the Castle Hayne Aquifer, rather than the River Bend Aquifer, and separates the Pungo River Aquifer from the upper Castle Hayne Aquifer. All geologic formations were bound by unconformities. All aquifers were confined by the anticipated hydrologic units. We conclude that CR-622 (Strat 8) represents a normal sequence in the Atlantic Coastal Plain.

Calculation of elastic properties in lower part of the Kola borehole from bulk chemical compositions of core samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babeyko, A.Yu.; Sobolev, S.V.; Sinelnikov, E.D.

1994-09-01

In-situ elastic properties in deep boreholes are controlled by several factors, mainly by lithology, petrofabric, fluid-filled cracks and pores. In order to separate the effects of different factors it is useful to extract lithology-controlled part from observed in-situ velocities. For that purpose we calculated mineralogical composition and isotropic crack-free elastic properties in the lower part of the Kola borehole from bulk chemical compositions of core samples. We use a new technique of petrophysical modeling based on thermodynamic approach. The reasonable accuracy of the modeling is confirmed by comparison with the observations of mineralogical composition and laboratory measurements of density andmore » elastic wave velocities in upper crustal crystalline rocks at high confining pressure. Calculations were carried out for 896 core samples from the depth segment of 6840-10535m. Using these results we estimate density and crack-free isotropic elastic properties of 554 lithology-defined layers composing this depth segment. Average synthetic P-wave velocity appears to be 2.7% higher than the velocity from Vertical Seismic Profiling (VSP), and 5% higher than sonic log velocity. Average synthetic S-wave velocity is 1.4% higher than that from VSP. These differences can be explained by superposition of effects of fabric-related anisotropy, cracks aligned parallel to the foliation plain, and randomly oriented cracks, with the effects of cracks being the predominant control. Low sonic log velocities are likely caused by drilling-induced cracking (hydrofractures) in the borehole walls. The calculated synthetic density and velocity cross-sections can be used for much more detailed interpretations, for which, however, new, more detailed and reliable seismic data are required.« less

Use of structural geology in exploration for and mining of sedimentary rock-hosted Au deposits

USGS Publications Warehouse

Peters, Stephen G.

2001-01-01

Structural geology is an important component in regional-, district- and orebody-scale exploration and development of sedimentary rock-hosted Au deposits.Identification of timing of important structural events in an ore district allows analysis and classification of fluid conduits and construction of genetic models for ore formation.The most practical uses of structural geology deal with measurement and definition of various elements that comprise orebodies, which can then be directly applied to ore-reserve estimation,ground control,grade control, safety issues,and mine planning.District- and regional-scale structural studies are directly applicable to long-term strategic planning,economic analysis,and land ownership. Orebodies in sedimentary rock-hosted Au deposits are discrete, hypogene, epigenetic masses usually hosted in a fault zone,breccia mass, or lithologic bed or unit. These attributes allow structural geology to be directly applied to the mining and exploration of sedimentary rock-hosted Au deposits. Internal constituents in orebodies reflect unique episodes relating to ore formation.The main internal constituents in orebodies are ore minerals, gangue, and alteration minerals that usually are mixed with one another in complex patterns, the relations among which may be used to interpret the processes of orebody formation and control.Controls of orebody location and shape usually are due to structural dilatant zones caused by changes in attitude, splays, lithologic contacts,and intersections of the host conduit or unit.In addition,conceptual parameters such as district fabric,predictable distances, and stacking also are used to understand the geometry of orebodies.Controls in ore districts and location and geometry of orebodies in ore districts can be predicted to various degrees by using a number of qualitative concepts such as internal and external orebody plunges,district plunge, district stacking, conduit classification, geochemical, geobarometric and geothermal gradients, and tectonic warps. These concepts have practical and empirical application in most mining districts where they are of use in the exploration for ore, but are of such broad and general application that they may not represent known or inferred ore formation processes. Close spatial relation among some sedimentary rock- hosted Au deposits and their host structures suggests that the structures and the orebodies are genetically linked because they may have shared the same developmental history. Examples of probable syn-deformational genesis and structural control of sedimentary rock-hosted Au deposits are in the large Betze deposit in the Carlin trend, Nevada and in the Lannigou, Jinlongshan, and Maanqiao Au deposits, China.

Le Viséen supérieur d'Azarhare (Maroc central) : environnements de dépôt, datation et évolution diagánótique

NASA Astrophysics Data System (ADS)

Karim, Atika; Berkhli, Mostafa; Vachard, Daniel; Tribovillard, Nicolas; Orberger, Beate

2005-04-01

The unexplored area of Azarhare in central Morocco is studied thanks to three sections composed of five lithological facies Main biostratigraphical and sedimentological results concern (1) the identification of Late Visean biozones, with important presence of problematic algae Ungdarella, (2) the regional extension of deposit sequences SD5, SD6 and SD7 previously defined, (3) and an analysis of the diagenetic kaolinite. To cite this article: A. Karim et al., C. R. Geoscience 337 (2005).

MAGSAT project

NASA Technical Reports Server (NTRS)

1981-01-01

Programs for the conversion of MAGSAT tapes (both CHRONICLE and CHRONINT formats) from IBM binary to DEC 10 binary were developed in ASSEMBLY language) and programs for selection of only a particular part of CHRONICLE tape (e.g., passes over the Indian subcontinent) were also prepared. Data on a few selected quiet and disturbed days were studied by substracting the main field, and the anomalies over the Indian region were partly identified on few of the passes. A national Workshop on MAGSAT was arranged. The potentialities and usefulness of MAGSAT data particularly in the study of crustal lithology was discussed.

Litho- and chemostratigraphy of the Flatreef PGE deposit, northern Bushveld Complex

NASA Astrophysics Data System (ADS)

Grobler, D. F.; Brits, J. A. N.; Maier, W. D.; Crossingham, A.

2018-05-01

The Flatreef is a world-class platinum-group element (PGE) deposit recently discovered down-dip from existing mining and exploration operations on the northern limb of the Bushveld Complex. Current indicated resources stand at 42 Moz PGE (346 Mt with 3.8 g/t Pt+Pd+Rh+Au, 0.32% Ni and 0.16% Cu) which, in the case of Pt, is equivalent to 10 years global annual production, making it one of the largest PGE deposits on earth. The grade and thickness of the Flatreef mineralised interval is highly unusual, with some drill core intersections containing up to 4.5 g/t Pt+Pd+Rh+Au over 90 m in drill core. Here, we document the down-dip and along-strike litho- and chemostratigraphy of the Flatreef and its footwall and hanging wall rocks, based on a diamond drill core database totalling > 720 km. At the base of the sequence intersected in the drill cores are up to 700-m-thick sills of ultramafic rocks (dunite, harzburgite, pyroxenite) emplaced into pelitic, dolomitic, and locally quartzitic and evaporitic rocks belonging to the Duitschland Formation of the Transvaal Supergroup. Next is an approximately 100-200-m sequence of low-grade-sulphide-mineralised, layered mafic-ultramafic rocks containing abundant sedimentary xenoliths and, in places, several chromite seams or stringers. This is overlain by a 100-m-thick sequence of well-mineralised mafic-ultramafic rocks (the Flatreef sensu strictu), overlain by a laterally persistent mottled compositional analogies at the base of > 1 km of homogenous Main Zone gabbronorite. Based on stratigraphic, lithological and compositional alanalogies to the layered rocks in the eastern and western Bushveld Complex, we correlate the Flatreef and its chromite bearing footwall rocks with the Upper Critical Zone, notably the interval between the UG2 chromitite and the Bastard Reef as found elsewhere in the Bushveld Complex. This includes recognition of a Merensky Reef correlative. The ultramafic rocks below the main chromitite seam (UG2 correlative) in the Flatreef footwall are correlated with the Lower Critical and Lower zones. However, compared to the western and eastern Bushveld limbs, the studied sequence is strongly enriched in sulphide and PGE, many of the rocks show elevated CaO, K2O, Rb and Zr contents, and lateral continuity of layers between drill cores is less pronounced than elsewhere in the Bushveld, whereas ultramafic units are locally considerably thickened. These compositional and lithological traits are interpreted to result from a range of processes which include contamination with calcsilicate and hornfels, intrusion of granitic magmas, and the influence of multiple structural events such as pre- to syn-emplacement regional-scale open folding and growth faults. Evidence for the existence of potholes also exists. In the shallow, up-dip portions of the project area, the entire magmatic sequence below the Main Zone becomes increasingly contaminated to the extent that individual units are somewhat more difficult to correlate between drill cores. This package represents the Platreef as exposed in outcrop and shallow bore holes across much of the northern limb of the Bushveld Complex. The new data presented here thus indicate that the Platreef is a relatively more contaminated up-dip extension of parts of the Critical and Lower zones.

Soil Components in Heterogeneous Impact Glass in Martian Meteorite EETA79001

NASA Technical Reports Server (NTRS)

Schrader, C. M.; Cohen, B. A.; Donovan, J. J.; Vicenzi, E. P.

2010-01-01

Martian soil composition can illuminate past and ongoing near-surface processes such as impact gardening [2] and hydrothermal and volcanic activity [3,4]. Though the Mars Exploration Rovers (MER) have analyzed the major-element composition of Martian soils, no soil samples have been returned to Earth for detailed chemical analysis. Rao et al. [1] suggested that Martian meteorite EETA79001 contains melted Martian soil in its impact glass (Lithology C) based on sulfur enrichment of Lithology C relative to the meteorite s basaltic lithologies (A and B) [1,2]. If true, it may be possible to extract detailed soil chemical analyses using this meteoritic sample. We conducted high-resolution (0.3 m/pixel) element mapping of Lithology C in thin section EETA79001,18 by energy dispersive spectrometry (EDS). We use these data for principal component analysis (PCA).

An olivine-free mantle lithology as a source for mantle-derived magmas: the role of metasomes in the Ethiopian-Arabian large igneous province.

NASA Astrophysics Data System (ADS)

Rooney, T. O.; Nelson, W. R.; Ayalew, D.; Yirgu, G.; Herzberg, C. T.; Hanan, B. B.

2014-12-01

Peridotite constitutes most of the Earth's upper mantle, and it is therefore unsurprising that most mantle-derived magmas exhibit evidence of past equilibrium with olivine-dominated source. There is mounting evidence, however, for the role of pyroxenite in magma generation within upwelling mantle plumes; a less documented non-peridotite source of melts are metasomatic veins (metasomes) within the lithospheric mantle. Melts derived from metasomes may exhibit extreme enrichment or depletion in major and trace elements. We hypothesize that phenocrysts such as olivine, which are commonly used to probe basalt source lithology, will reflect these unusual geochemical signals. Here we present preliminary major and trace element analyses of 60 lavas erupted from a small Miocene shield volcano located within the Ethiopian flood basalt province. Erupted lavas are intercalated with lahars and pyroclastic horizons that are overlain by a later stage of activity manifested in small cinder cones and flows. The lavas form two distinctive petrographic and geochemical groups: (A) an olivine-phyric, low Ti group (1.7-2.7 wt. % TiO2; 4.0-13.6 wt. % MgO), which geochemically resembles most of the basalts in the region. These low Ti lavas are the only geochemical unit identified in the later cinder cones and associated lava flows. (B) a clinopyroxene-phyric high Ti group (1-6.7 wt. % TiO2; 1.0-9.5 wt. % MgO), which resembles the Oligocene HT-2 flood basalts. This unit is found intercalated with low Ti lavas within the Miocene shield. In comparison to the low Ti group, the high Ti lavas exhibit a profound depletion in Ni, Cr, Al, and Si, and significant enrichment in Ca, Fe, V, and the most incompatible trace elements. When combined with a diagnostic negative K anomaly in primitive-mantle normalized diagrams and Na2O>K2O, the geochemical data point towards a source which is rich in amphibole, devoid of olivine, and perhaps containing some carbonate. Our preliminary results have identified a large suite of primitive lavas derived from a nominally olivine-free mantle source. Consequently, our future work will examine olivine geochemical characteristics and constrain the compositional space for these unusual mantle lithologies.

Comparison of lithological mapping results from airborne hyperspectral VNIR-SWIR, LWIR and combined data

NASA Astrophysics Data System (ADS)

Feng, Jilu; Rogge, Derek; Rivard, Benoit

2018-02-01

This study investigates using the Airborne Hyperspectral Imaging Systems (AISA) visible and short-wave infrared (SWIR) and Spatially Enhanced Broadband Array Spectrograph System (SEBASS) longwave infrared (LWIR) (2 and 4 m spatial resolution, respectively) imagery independently and in combination to produce detailed lithologic maps in a subarctic region (Cape Smith Belt, Nunavik, Canada) where regionally metamorphosed lower greenschist mafic, ultramafic and sedimentary rocks are exposed in the presence of lichen coatings. We make use of continuous wavelet analysis (CWA) to improve the radiometric quality of the imagery through the minimization of random noise and the enhancement of spectral features, the minimization of residual errors in the ISAC radiometric correction and target temperature estimation in the case of the LWIR data, the minimization of line to line residual calibration effects that lead to inconsistencies in data mosaics, and the reduction in variability of the spectral continuum introduced by variable illumination and topography. The use of CWA also provides a platform to directly combine the wavelet scale spectral profiles of the SWIR and LWIR after applying a scalar correction factor to the LWIR such that the dynamic range of two data sets have equal weight. This is possible using CWA as the datasets are normalized to a zero mean allowing spectra from different spectral regions to be adjoined. Lithologic maps are generated using an iterative spectral unmixing approach with image spectral endmembers extracted from the SWIR and LWIR imagery based on locations defined from previous work of the study area and field mapping information. Unmixing results of the independent SWIR and LWIR data, and the combined data show clear benefits to using the CWA combined imagery. The analysis showed SWIR and LWIR imagery highlight similar regions and spatial distributions for the three ultramafic units (dunite, peridotite, pyroxenite). However, significant differences are observed for quartz-rich sediments, with the SWIR overestimating the distribution of these rocks whereas the LWIR provided more consistent results compared with existing maps. Both SWIR and LWIR imagery were impacted by the pervasive lichen coatings on the mafic rocks (basalts and gabbros), although the SWIR provided better results than the LWIR. Limitations observed for the independent data sets were removed using the combined spectral data resulting in all geologically meaningful units mapped correctly in comparison with existing geological maps.

Carbonate rocks of Cambrian and Ordovician age in the Lancaster quadrangle, Pennsylvania

USGS Publications Warehouse

Meisler, Harold; Becher, Albert E.

1968-01-01

Detailed mapping has shown that the carbonate rocks of Cambrian and Ordovician age in the Lancaster quadrangle, Pennsylvania, can be divided into 14 rock-stratigraphic units. These units are defined primarily by their relative proportions of limestone and dolomite. The oldest units, the Vintage, Kinzers, and Ledger Formations of Cambrian age, and the Conestoga Limestone of Ordovician age are retained in this report. The Zooks Corner Formation, of Cambrian age, a dolomite unit overlying the Ledger Dolomite, is named here for exposures along Conestoga Creek near the village of Zooks Corner. The Conococheague (Cambrian) and Beekmantown (Ordovician) Limestones, as mapped by earlier workers, have been elevated to group rank and subdivided into formations that are correlated with and named for geologic units in Lebanon and Berks Counties, Pa. These formations, from oldest to youngest, are the Buffalo Springs, Snitz Creek, Millbach, and Richland Formations of the Conococheague Group, and the Stonehenge, Bpler, and Ontelaunee Formations of the Beekmantown Group. The Annville and Myerstown Limestones, which are named for lithologically similar units in Dauphin and Lebanon Counties, Pa., overlie the Beekmantown Group in one small area in the quadrangle.

Sequence stratigraphy of the lower Upper Cretaceous Elbtal Group (Saxony, Germany): new data from Middle Cenomanian-Upper Turonian outcrops and boreholes

NASA Astrophysics Data System (ADS)

Richardt, Nadine; Wilmsen, Markus

2013-04-01

The formations of the Saxonian Cretaceous have been combined in the so-called Elbtal Group. Their sedimentation took place in a terrestrial to neritic environment palaeogeographically located between the Mid-European Island (MEI) in the SW and the Lusatian Massif in the NE. The through extended from the narrow marine strait of Saxony into the broad Bohemian Cretaceous Basin (Czech Republic) further to the SE. Deposition has been dominated by marine siliciclastics that accumulated on a graded shelf with basically three main facies zones: the coarse-grained nearshore zone ("Küstensandsteinzone"), the transitional zone ("Faziesübergangszone") and the fine-grained marly offshore facies zone ("Plänerfazies"). In general, transgression proceeded in late Early Cenomanian times from the N. Relictic remains of these marine bioclastic conglomerates (Meißen Formation) only occur in the northwesternmost area of the basin around Meißen and are related to the highstand of the depositional sequence Cenomanian 3 (DS Ce 3). After a short stratigraphic gap, onlap continued in the Middle Cenomanian with the following Niederschöna Formation consisting of coarse-grained braided river deposits at the base grading via carbonaceous point-bar cycles of a meandering river system into bioturbated, partly cross-bedded estuarine sediments toward the top. These sediments record DS Ce 4 and are capped by a paleosol. Sedimentation of DS Ce 5 started with a renewed transgressional pulse initiating the Late Cenomanian. The strata consist of bioturbated, cross-bedded predominantly fine- to medium-grained quartz sandstones with some shell-rich horizons corresponding to the Oberhäslich Formation. The unconformably overlying DS Tu 1 comprises the uppermost Cenomanian Dölzschen Formation and the Lower Turonian part of the Schmilka Formation. The onset of this depositional sequence is marked by a major transgression ("plenus Transgression) drowning the remaining pre-transgression topography (onlap of Dölzschen Formation onto basement highs). The lowermost Turonian "Lohmgrund Marl" defines the base of the Schmilka Formation changing gradually into strongly bioturbated, silty Pläner and coarsening upward into moderately bioturbated, thick-bedded-massive, mainly fine-grained quartz sandstones with occasional clayey or silty layers, shell-rich horizons and sparse wood remains. After an interruption in sedimentation indicated by a root horizon or a conspicuous erosional surface, the Schmilka Formation continues with similar lithology into the early Middle Turonian. It is replaced up-section by the overlying Middle-Upper Turonian Postelwitz Formation, characterized by decreasing thickness of bedding and stronger sedimentary variability (grain size, bioturbation, glauconite and fossil content), including the intercalation of thick units of silty Pläner. The lithological variations of sandy and Pläner intervals nicely reflect the Middle-Late Turonian sea-level changes of DS Tu 2 (early Middle Turonian), DS Tu 3 (late Middle-earliest Late Turonian) and DS Tu 4 (early Late-mid-Late Turonian): Pläner units represent transgressive and highstand conditions, sand packages late highstand as well as falling and lowstand systems tracts. A major mid-Late Turonian sea-level fall is indicated in the upper Postelwitz Formation, initiating DS Tu 5 (Late Turonian) with a strongly basin-ward prograding unit of coarse-grained sandstone. The following transgression culminated in a prominent maximum flooding interval represented by the intercalation of a clayey-fine-grained regional marker bed, forming the base of the Schrammstein Formation (thick-bedded, unfossiliferous medium- to coarse-grained quartz sandstones). In conclusion, all depositional sequences of Middle Cenomanian-Late Turonian age and their bounding unconformities (sequence boundaries SB Ce 4 and 5, SB Tu 1-4) reported from coeval sections around the MEI (e. g., Münsterland Creatceous Basin, Lower Saxonian and Danubian Cretaceous) and other Cretaceous basins in the Tethyan region (e. g., Egypt) are also developed in the Saxonian Cretaceous, supporting eustatic sea-level changes as main triggers for the sequence stratigraphic architecture of the Elbtal Group.

Digital Data for the reconnaissance geologic map for the Kuskokwim Bay Region of Southwest Alaska

USGS Publications Warehouse

Wilson, Frederic H.; Hults, Chad P.; Mohadjer, Solmaz; Coonrad, Warren L.; Shew, Nora B.; Labay, Keith A.

2008-01-01

INTRODUCTION The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Multi-scale strain localization within orthogneiss during subduction and exhumation (Tenda unit, Alpine Corsica)

NASA Astrophysics Data System (ADS)

Beaudoin, Alexandre; Augier, Romain; Jolivet, Laurent; Raimbourg, Hugues; Jourdon, Anthony; Scaillet, Stéphane; Cardello, Giovanni Luca

2016-04-01

Strain localization depends upon scale-related factors resulting in a gap between small-scale studies of deformation mechanisms and large-scale numerical and tectonic models. The former often ignore the variations in composition and water content across tectonic units, while the latter oversimplify the role of the deformation mechanisms. This study aims to heal this gap, by considering microstructures and strain localization not only at a single shear zone-scale but across a 40km-wide tectonic unit and throughout its complex polyphased evolution. The Tenda unit (Alpine Corsica) is an external continental unit mainly composed of granites, bounded by the East Tenda Shear Zone (ETSZ) that separates it from the overlying oceanic-derived HP tectonic units. Previous studies substantially agreed on (1) the burial of the Tenda unit down to blueschist-facies conditions associated with top-to-the-west shearing (D1) and (2) subsequent exhumation accommodated by a localized top-to-the-east shear zone (D2). Reaction-softening is the main localizing mechanism proposed in the literature, being associated with the transformation of K-feldspar into white-mica. In this work, the Tenda unit is reviewed through (1) the construction of a new field-based strain map accompanied by cross-sections representing volumes of rock deformed at different grades related to large-scale factors of strain localization and (2) the structural study of hand-specimens and thin-sections coupled with EBSD analysis in order to target the deformation processes. We aim to find how softening and localization are in relation to the map-scale distribution of strain. The large-scale study shows that the whole Tenda unit is affected by the two successive stages of deformation. However, a more intense deformation is observed along the eastern margin, which originally led to the definition of the ETSZ, with a present-day anastomosed geometry of deformation. Strain localization is clearly linked to rheological/lithological contrasts as it concentrates either along preexisting intrusive and tectonic contacts. As K-feldspar-poor granites remain relatively undeformed, reaction-softening seems to be a major mechanism during D1. However, evidences suggest that this mechanism is in competition with dynamic recrystallization: at outcrop and hand-specimen scale, the correlation between localized structures such as C-planes and phengite-rich zones is not always observed. This same competition remains active during D2 where top-to-the-east C-planes are common in phengite-rich layers, but an overall grain-size reduction is also observed across the different strain grades, suggesting that dynamic recrystallization remains active during the whole story. Final localization is sometimes observed in phengite-poor aplitic ultramylonites characterized by a very fine quartz-albite matrix suggesting that grain-size sensitive flow would be the major mechanism involved in the final rheology of the ETSZ.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance bedrock geologic map for the northern Alaska peninsula area, southwest Alaska

USGS Publications Warehouse

,

2006-01-01

he growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance geologic map of the western Aleutian Islands, Alaska

USGS Publications Warehouse

,

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO Exportfiles/ and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the generalized bedrock geologic map, Yukon Flats region, east-central Alaska

USGS Publications Warehouse

Till, Alison B.; Dumoulin, Julie A.; Phillips, Jeffrey D.; Stanley, Richard G.; Crews, Jessie

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Preliminary integrated geologic map databases for the United States: Digital data for the reconnaissance geologic map of the lower Yukon River region, Alaska

USGS Publications Warehouse

,

2006-01-01

The growth in the use of Geographic Information Systems (GIS) has highlighted the need for digital geologic maps that have been attributed with information about age and lithology. Such maps can be conveniently used to generate derivative maps for manifold special purposes such as mineral-resource assessment, metallogenic studies, tectonic studies, and environmental research. This report is part of a series of integrated geologic map databases that cover the entire United States. Three national-scale geologic maps that portray most or all of the United States already exist; for the conterminous U.S., King and Beikman (1974a,b) compiled a map at a scale of 1:2,500,000, Beikman (1980) compiled a map for Alaska at 1:2,500,000 scale, and for the entire U.S., Reed and others (2005a,b) compiled a map at a scale of 1:5,000,000. A digital version of the King and Beikman map was published by Schruben and others (1994). Reed and Bush (2004) produced a digital version of the Reed and others (2005a) map for the conterminous U.S. The present series of maps is intended to provide the next step in increased detail. State geologic maps that range in scale from 1:100,000 to 1:1,000,000 are available for most of the country, and digital versions of these state maps are the basis of this product. The digital geologic maps presented here are in a standardized format as ARC/INFO export files and as ArcView shape files. Data tables that relate the map units to detailed lithologic and age information accompany these GIS files. The map is delivered as a set 1:250,000-scale quadrangle files. To the best of our ability, these quadrangle files are edge-matched with respect to geology. When the maps are merged, the combined attribute tables can be used directly with the merged maps to make derivative maps.

Upper Cenozoic sediments of the lower Delaware Valley and the northern Delmarva Peninsula, New Jersey, Pennsylvania, Delaware, and Maryland

USGS Publications Warehouse

Owens, James Patrick; Minard, James Pierson

1979-01-01

The 'yellow gravels' referred to by R. D. Salisbury in 1898 and the 'Trenton gravel,' as defined by H. C. Lewis in 1880, were investigated along the inner edge of the New Jersey Coastal Plain in southern New Jersey and in the northern Delmarva Peninsula. The highest level deposits, the Beacon Hill gravel, are found on only the highest hills in the New Jersey Coastal Plain. Their distribution suggests deposition from north to south across the plain. After deposition of the Beacon Hill, probably in middle or late Miocene time, a narrow valley was formed paralleling the inner edge of the New Jersey Coastal Plain between Raritan Bay and Camden. South of Camden, the valley broadened, covering much of southern New Jersey. The deposits in this valley are largely the Bridgeton Formation as we have redefined it. A second narrow valley was entrenched through the Bridgeton between Trenton and Salem, N.J. This valley broadens and covers much of the northern Delmarva Peninsula west of the Delaware River. The fill in the valley is largely the Pensauken Formation, as we have redefined it in our report. Collectively, the Beacon Hill, the Bridgeton, and the Pensauken were originally the 'yellow gravels' of Salisbury. These deposits are all fluviatile in origin and were largely formed as a series of step like downcutting channels. The Delaware Valley between Trenton and the lower Delaware Bay region is occupied by the 'Trenton gravel,' which is below the average level of the 'yellow gravels.' Two units recognized throughout the area and informally named the Spring Lake beds and the Van Sciver Lake beds are lithologically distinct from the 'yellow gravel' formations. The lithologies of the Spring Lake beds and the Van Sciver Lake beds are much more heterogeneous than those of the older formations. These two units, particularly, contain much greater amounts of silt and clay, often in thick beds. The depositional environments associated with the two units include fluviatile, estuarine, and marginal marine. Both these units are interpreted to be late Pleistocene (Sangamonian) in age.

Terrestrial Ecosystems of the Conterminous United States

USGS Publications Warehouse

Sayre, Roger G.; Comer, Patrick; Cress, Jill; Warner, Harumi

2010-01-01

The U.S. Geological Survey (USGS), with support from NatureServe, has modeled the potential distribution of 419 terrestrial ecosystems for the conterminous United States using a comprehensive biophysical stratification approach that identifies distinct biophysical environments and associates them with known vegetation distributions (Sayre and others, 2009). This standardized ecosystem mapping effort used an ecosystems classification developed by NatureServe (Comer and others, 2003). The ecosystem mapping methodology was developed for South America (Sayre and others, 2008) and is now being implemented globally (Sayre and others, 2007). The biophysical stratification approach is based on mapping the major structural components of ecosystems (land surface forms, topographic moisture potential, surficial lithology, isobioclimates and biogeographic regions) and then spatially combining them to produce a set of unique biophysical environments. These physically distinct areas are considered as the fundamental structural units ('building blocks') of ecosystems, and are subsequently aggregated and labeled using the NatureServe classification. The structural footprints were developed from the geospatial union of several base layers including biogeographic regions, isobioclimates (Cress and others, 2009a), land surface forms (Cress and others, 2009b), topographic moisture potential (Cress and others, 2009c), and surficial lithology (Cress and others, in press). Among the 49,168 unique structural footprint classes that resulted from the union, 13,482 classes met a minimum pixel count threshold (20,000 pixels) and were aggregated into 419 NatureServe ecosystems using a semiautomated labeling process based on rule-set formulations for attribution of each ecosystem. The resulting ecosystems are those that are expected to occur based on the combination of the bioclimate, biogeography, and geomorphology. Where land use by humans has not altered land cover, natural vegetation assemblages are expected to occur, and these are described in the ecosystems classification. The map does not show the distribution of urban and agricultural areas - these will be masked out in subsequent analyses to depict the current land cover in addition to the potential distribution of natural ecosystems. This map depicts the smoothed and generalized image of the terrestrial ecosystems dataset. Additional information about this map and any data developed for the ecosystems modeling of the conterminous United States is available online at: http://rmgsc.cr.usgs.gov/ecosystems/.

Geology of the Side Crater of the Erebus volcano, Antarctica

NASA Astrophysics Data System (ADS)

Panter, Kurt S.; Winter, Brian

2008-11-01

The summit cone of the Erebus volcano contains two craters. The Main crater is roughly circular (˜ 500 m diameter) and contains an active persistent phonolite lava lake ˜ 200 m below the summit rim. The Side Crater is adjacent to the southwestern rim of the Main Crater. It is a smaller spoon-shaped Crater (250-350 m diameter, 50-100 m deep) and is inactive. The floor of the Side Crater is covered by snow/ice, volcanic colluvium or weakly developed volcanic soil in geothermal areas (a.k.a. warm ground). But in several places the walls of the Side Crater provide extensive vertical exposure of rock which offers an insight into the recent eruptive history of Erebus. The deposits consist of lava flows with subordinate volcanoclastic lithologies. Four lithostratigraphic units are described: SC 1 is a compound lava with complex internal flow fabrics; SC 2 consists of interbedded vitric lavas, autoclastic and pyroclastic breccias; SC 3 is a thick sequence of thin lavas with minor autoclastic breccias; SC 4 is a pyroclastic fall deposit containing large scoriaceous lava bombs in a matrix composed primarily of juvenile lapilli-sized pyroclasts. Ash-sized pyroclasts from SC 4 consist of two morphologic types, spongy and blocky, indicating a mixed strombolian-phreatomagmatic origin. All of the deposits are phonolitic and contain anorthoclase feldspar. The stratigraphy and morphology of the Side Crater provides a record of recent volcanic activity at the Erebus volcano and is divided into four stages. Stage I is the building of the main summit cone and eruption of lavas (SC 1 and SC 3) from Main Crater vent(s). A secondary cone was built during Stage II by effusive and explosive activity (SC 2) from the Side Crater vent. A mixed strombolian and phreatomagmatic eruption (SC 4) delimits Stage III. The final stage (IV) represents a period of erosion and enlargement of the Side Crater.

Proposal for MSW contaminant classification applied to a tropical aquifer.

PubMed

de Faria, Gabriel Messias Moura; Mondelli, Giulliana

2018-04-01

Groundwater is a natural resource exploited worldwide causing danger due to the lixiviation of waste deposited, which presents high potential degradation. Internationally, regulation aims for the maintenance of the quality of this resource. But the local lithology, mainly in countries with tropical weather, was not considered. This paper has an objective to propose two methodologies of contaminant identification of municipal solid waste (MSW) considering the Brazilian regulation, the local lithology and the temporal aspect. The study site is located in the midwest of São Paulo, at the Marília Formation, Bauru Aquifer, which presents sandstone rich in calcite. At first, the historic monitoring data accumulated between 2002 and 2015 were statistically organized. Then, methodologies of classification of major constituents and contamination method were developed. After these analyses, the compounds that possibly cause anomaly in the local environment are Al, As, Ba, Ca, Cd, Co, Cr, Cu, phosphatic, nitrogenous, and sulfated compounds, Fe, K, Mn, Ni, and Pb. Some of these have lithogenic genesis typical of tropical environment, and others come from the disposed waste. Despite different approaches, both methods demonstrate efficiency in identifying the pollutants presenting distinctions among themselves in conjunction with actual local regulation and the lithogenic source of certain compounds.

Porosity Development in a Coastal Setting: A Reactive Transport Model to Assess the Influence of Heterogeneity of Hydrological, Geochemical and Lithological Conditions

NASA Astrophysics Data System (ADS)

Maqueda, A.; Renard, P.; Cornaton, F. J.

2014-12-01

Coastal karst networks are formed by mineral dissolution, mainly calcite, in the freshwater-saltwater mixing zone. The problem has been approached first by studying the kinetics of calcite dissolution and then coupling ion-pairing software with flow and mass transport models. Porosity development models require high computational power. A workaround to reduce computational complexity is to assume the calcite dissolution reaction is relatively fast, thus equilibrium chemistry can be used to model it (Sanford & Konikow, 1989). Later developments allowed the full coupling of kinetics and transport in a model. However kinetics effects of calcite dissolution were found negligible under the single set of assumed hydrological and geochemical boundary conditions. A model is implemented with the coupling of FeFlow software as the flow & transport module and PHREEQC4FEFLOW (Wissmeier, 2013) ion-pairing module. The model is used to assess the influence of heterogeneities in hydrological, geochemical and lithological boundary conditions on porosity evolution. The hydrologic conditions present in the karst aquifer of Quintana Roo coast in Mexico are used as a guide for generating inputs for simulations.

New bulk and in situ isotopic and elemental geochemistry of shallow drill core from Atlantis Massif: insights into the sources and paths of fluids and clasts

NASA Astrophysics Data System (ADS)

Bilenker, L.; Weis, D.; Scoates, J. S.

2017-12-01

We present stable Fe and radiogenic isotope and complementary trace element data for samples from Atlantis Massif. This oceanic core complex is located at 30°N where the Atlantis Transform Fault intersects the Mid-Atlantic Ridge (MAR) and is associated with the Lost City Hydrothermal Field (LCHF). It is a unique place to investigate the abiotic and biotic geochemical processes that play a role in the alteration of both crustal and mantle seafloor rocks. The samples analyzed represent a shallow (<15 m) survey of five drill sites (IODP Expedition 357) within Atlantis Massif, varying in distance from the LCHF and MAR. Analyses were performed on a sample set spanning a wide range in degree of alteration and lithology. Bulk measurements involved dissolving whole rock powders, whereas in situ analyses were performed on digested microdrilled samples or by laser ablation. Bulk rock Fe isotope values (n = 34) are correlated with loss-on-ignition (LOI) by sample lithology and location relative to LCHF. Using LOI as a proxy for degree of alteration, this observation indicates that the Fe isotope systematics of seafloor crustal and mantle rocks preserve indicators of fluid flow and source. The Hf and Nd isotope compositions for various lithologies form all analyzed sites are homogeneous, indicating minimal alteration of these isotopic systems. Bulk Sr values provide insight into elemental exchange between seawater and the surface of Atlantis Massif and bulk Pb isotopes allow for fingerprinting of the source of basalt breccias through comparison with published Pb isotope values of MAR basalts. The new results cluster around the Pb, Hf, Nd isotopic composition of mid-ocean ridge basalt from 30.68°N and do not match samples north or south of that location. In situ Fe isotope data within three altered samples reflect varying degrees of hydrothermal and seawater interaction, where the Fe isotope ratios within each sample are likely correlated with extent of exchange or redox. Laser trace element and Pb isotope data in progress will allow us to investigate this further. This study contributes to our understanding of element mobility and mass transfer during chemical reactions within the seafloor, provides insight into the source of the lithological units and fluid flow, and allows for quantification of alteration processes.

The nature and origin of mineral coatings on volcanic rocks of the Black Mountain, Stonewall Mountain and Kane Springs Wash volcanic centers in southern Nevada

NASA Technical Reports Server (NTRS)

Taranik, J. V.; Noble, D. D.; Hsu, L. C.; Hutsinpiller, A.

1986-01-01

Four LANDSAT thematic mapping scenes in southern Nevada were requested at two different acquisition times in order to assess the effect of vegetation on the signature of the volcanic units. The remote sensing data acquisition and analysis portion are nearly completed. The LANDSAT thematic mapping data is of good quality, and image analysis techniques are so far successful in delineating areas with distinct spectral characteristics. Spectrally distinct areas were correlated with variations in surface coating and lithologies of the volcanic rocks.

Geologic map of the Grand Canyon 30' x 60' quadrangle, Coconino and Mohave Counties, northwestern Arizona

USGS Publications Warehouse

Billingsley, G.H.

2000-01-01

This digital map database, compiled from previously published and unpublished data as well as new mapping by the author, represents the general distribution of bedrock and surficial deposits in the map area. Together with the accompanying pamphlet, it provides current information on the geologic structure and stratigraphy of the Grand Canyon area. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:100,000 or smaller.

Geochemical results from stream-water and stream-sediment samples collected in Colorado and New Mexico

USGS Publications Warehouse

Hageman, Philip L.; Todd, Andrew S.; Smith, Kathleen S.; DeWitt, Ed; Zeigler, Mathew P.

2013-01-01

Scientists from the U.S. Geological Survey are studying the relationship between watershed lithology and stream-water chemistry. As part of this effort, 60 stream-water samples and 43 corresponding stream-sediment samples were collected in 2010 and 2011 from locations in Colorado and New Mexico. Sample sites were selected from small to midsize watersheds composed of a high percentage of one rock type or geologic unit. Stream-water and stream-sediment samples were collected, processed, preserved, and analyzed in a consistent manner. This report releases geochemical data for this phase of the study.

Lithology and Bedrock Geotechnical Properties in Controlling Rock and Ice Mass Movements in Mountain Cryosphere

NASA Astrophysics Data System (ADS)

Karki, A.; Kargel, J. S.

2017-12-01

Landslides and ice avalanches kill >5000 people annually (D. Petley, 2012, Geology http://dx.doi.org/10.1130/G33217.1); destroy or damage homes and infrastructure; and create secondary hazards, such as flooding due to blocked rivers. Critical roles of surface slope, earthquake shaking, soil characteristics and saturation, river erosional undercutting, rainfall intensity, snow loading, permafrost thaw, freeze-thaw and frost shattering, debuttressing of unstable masses due to glacier thinning, and vegetation burn or removal are well-known factors affecting landslides and avalanches. Lithology-dependent bedrock physicochemical-mechanical properties—especially brittle elastic and shear strength, and chemical weathering properties that affect rock strength, are also recognized controls on landsliding and avalanching, but are not commonly considered in detail in landslide susceptibility assessment. Lithology controls the formation of weakened, weathered bedrock; the formation and accumulation of soils; soil saturation-related properties of grain size distribution, porosity, and permeability; and soil creep related to soil wetting-drying and freeze-thaw. Lithology controls bedrock abrasion and glacial erosion and debris production rates, the formation of rough or smoothed bedrock surface by glaciation, fluvial, and freeze-thaw processes. Lithologic variability (e.g., bedding; fault and joint structure) affects contrasts in chemical weathering rates, porosity, and susceptibility to frost shattering and chemical weathering, hence formation of overhanging outcrops and weakened slip planes. The sudden failure of bedrock or sudden slip of ice on bedrock, and many other processes depend on rock lithology, microstructure (porosity and permeability), and macrostructure (bedding; faults). These properties are sometimes considered in gross terms for landslide susceptibility assessment, but in detailed applications to specific development projects, and in detailed mapping over large areas, the details of rock lithology, weathering state, and structure are rarely considered. We have initiated a geological and rock mechanical properties approach to landslide susceptibility assessments in areas of high concern for human and infrastructure safety.

Combining sediment fingerprinting and a conceptual model for erosion and sediment transfer to explore sediment sources in an Alpine catchment

NASA Astrophysics Data System (ADS)

Costa, A.; Stutenbecker, L.; Anghileri, D.; Bakker, M.; Lane, S. N.; Molnar, P.; Schlunegger, F.

2017-12-01

In Alpine basins, sediment production and transfer is increasingly affected by climate change and human activities, specifically hydropower exploitation. Changes in sediment sources and pathways significantly influence basin management, biodiversity and landscape evolution. We explore the dynamics of sediment sources in a partially glaciated and highly regulated Alpine basin, the Borgne basin, by combining geochemical fingerprinting with the modelling of erosion and sediment transfer. The Borgne basin in southwest Switzerland is composed of three main litho-tectonic units, which we characterised following a tributary-sampling approach from lithologically characteristic sub-basins. We analysed bulk geochemistry using lithium borate fusion coupled with ICP-ES, and we used it to discriminate the three lithologic sources using statistical methods. Finally, we applied a mixing model to estimate the relative contributions of the three sources to the sediment sampled at the outlet. We combine results of the sediment fingerprinting with simulations of a spatially distributed conceptual model for erosion and transport of fine sediment. The model expresses sediment erosion by differentiating the contributions of erosional processes driven by erosive rainfall, snowmelt, and icemelt. Soil erodibility is accounted for as function of land-use and sediment fluxes are linearly convoluted to the outlet by sediment transfer rates for hillslope and river cells, which are a function of sediment connectivity. Sediment connectivity is estimated on the basis of topographic-hydraulic connectivity, flow duration associated with hydropower flow abstraction and permanent storage in hydropower reservoirs. Sediment fingerprinting at the outlet of the Borgne shows a consistent dominance (68-89%) of material derived from the uppermost, highly glaciated reaches, while contributions of the lower part (10-25%) and middle part (1-16%), where rainfall erosion is predominant, are minor. This result is confirmed by the model simulation which shows that, despite the large flow abstraction (about 90%), the upstream reaches contribute the most of the sediments. This study shows how combining geochemical techniques and sediment erosion models provides insight in the dynamics of sediment sources.

Mississippian Barnett Shale, Fort Worth basin, north-central Texas: Gas-shale play with multi-trillion cubic foot potential

USGS Publications Warehouse

Montgomery, S.L.; Jarvie, D.M.; Bowker, K.A.; Pollastro, R.M.

2005-01-01

The Mississippian Barnett Shale serves as source, seal, and reservoir to a world-class unconventional natural-gas accumulation in the Fort Worth basin of north-central Texas. The formation is a lithologically complex interval of low permeability that requires artificial stimulation to produce. At present, production is mainly confined to a limited portion of the northern basin where the Barnett Shale is relatively thick (>300 ft; >92 m), organic rich (present-day total organic carbon > 3.0%), thermally mature (vitrinite reflectance > 1.1%), and enclosed by dense limestone units able to contain induced fractures. The most actively drilled area is Newark East field, currently the largest gas field in Texas. Newark East is 400 mi2 (1036 km2) in extent, with more than 2340 producing wells and about 2.7 tcf of booked gas reserves. Cumulative gas production from Barnett Shale wells through 2003 was about 0.8 tcf. Wells in Newark East field typically produce from depths of 7500 ft (2285 m) at rates ranging from 0.5 to more than 4 mmcf/day. Estimated ultimate recoveries per well range from 0.75 to as high as 7.0 bcf. Efforts to extend the current Barnett play beyond the field limits have encountered several challenges, including westward and northward increases in oil saturation and the absence of lithologic barriers to induced fracture growth. Patterns of oil and gas occurrence in the Barnett, in conjunction with maturation and burial-history data, indicate a complex, multiphased thermal evolution, with episodic expulsion of hydrocarbons and secondary cracking of primary oils to gas in portions of the basin where paleotemperatures were especially elevated. These and other data imply a large-potential Barnett resource for the basin as a whole (possibly > 200 tcf gas in place). Recent assessment by the U.S. Geological Survey suggests a mean volume of 26.2 tcf of undiscovered, technically recoverable gas in the central Fort Worth basin. Recovery of a significant portion of this undiscovered resource will require continued improvements in geoscientific characterization and approaches to stimulation of the Barnett reservoirs. Copyright ?? 2005. The American Association of Petroleum Geologists. All rights reserved.

Lithology of the long sediment record recovered by the ICDP Dead Sea Deep Drilling Project (DSDDP)

NASA Astrophysics Data System (ADS)

Neugebauer, Ina; Brauer, Achim; Schwab, Markus J.; Waldmann, Nicolas D.; Enzel, Yehouda; Kitagawa, Hiroyuki; Torfstein, Adi; Frank, Ute; Dulski, Peter; Agnon, Amotz; Ariztegui, Daniel; Ben-Avraham, Zvi; Goldstein, Steven L.; Stein, Mordechai

2014-10-01

The sedimentary sections that were deposited from the Holocene Dead Sea and its Pleistocene precursors are excellent archives of the climatic, environmental and seismic history of the Levant region. Yet, most of the previous work has been carried out on sequences of lacustrine sediments exposed at the margins of the present-day Dead Sea, which were deposited only when the lake surface level rose above these terraces (e.g. during the Last Glacial period) and typically are discontinuous due to major lake level variations in the past. Continuous sedimentation can only be expected in the deepest part of the basin and, therefore, a deep drilling has been accomplished in the northern basin of the Dead Sea during winter of 2010-2011 within the Dead Sea Deep Drilling Project (DSDDP) in the framework of the ICDP program. Approximately 720 m of sediment cores have been retrieved from two deep and several short boreholes. The longest profile (5017-1), revealed at a water depth of ˜300 m, reaches 455 m below the lake floor (blf, i.e. to ˜1175 m below global mean sea level) and comprises approximately the last 220-240 ka. The record covers the upper part of the Amora (penultimate glacial), the Last Interglacial Samra, the Last Glacial Lisan and the Holocene Ze'elim Formations and, therewith, two entire glacial-interglacial cycles. Thereby, for the first time, consecutive sediments deposited during the MIS 6/5, 5/4 and 2/1 transitions were recovered from the Dead Sea basin, which are not represented in sediments outcropping on the present-day lake shores. In this paper, we present essential lithological data including continuous magnetic susceptibility and geochemical scanning data and the basic stratigraphy including first chronological data of the long profile (5017-1) from the deep basin. The results presented here (a) focus on the correlation of the deep basin deposits with main on-shore stratigraphic units, thus providing a unique comprehensive stratigraphic framework for regional paleoenvironmental reconstruction, and (b) highlight the outstanding potential of the Dead Sea deep sedimentary archive to record hydrological changes during interglacial, glacial and transitional intervals.

Geochronological study of zircons from continental crust rocks in the Frido Unit (southern Apennines)

NASA Astrophysics Data System (ADS)

Laurita, Salvatore; Prosser, Giacomo; Rizzo, Giovanna; Langone, Antonio; Tiepolo, Massimo; Laurita, Alessandro

2015-01-01

Zircon crystals have been separated from gneisses and metagranitoids of the Pollino area (southern Apennines) in order to unravel the origin of these crustal slices within the ophiolite-bearing Frido Unit. The morphology of the zircon has been investigated by SEM, and the internal structure was revealed by cathodoluminescence. Data obtained by U/Pb dating have been used to deduce the age and significance of the different crystallization stages of zircon, connected to the evolutionary stages of the continental crust (Late Paleozoic-Early Mesozoic). Zircons in gneisses are characterized by inherited cores of magmatic origin, bordered by metamorphic rims. Inherited zircons generally show Paleoproterozoic to Ordovician ages, indicating the provenance of the sedimentary protolith from different sources. The exclusive presence of Late Neoproterozoic zircon cores in leucocratic gneisses may suggest a different magmatic source possibly connected to Pan-African events. Late Carboniferous-Early Permian ages are found mainly in zircon rims of metamorphic origin. These are similar to the emplacement ages of protolith of the metagranites in the middle crust portion. Late Carboniferous-Early Permian metamorphism and magmatism testify the extensional collapse of the Hercynian belt, recorded in European, particularly, in the Corsica-Sardinia block and in Calabria. Late Permian-Triassic ages have been detected in zircon rims from gneisses and metagranitoids. These younger ages appear related to deformation and emplacement of albite-quartz veins in both lithologies, and are related to an extensional episode predating the Middle Triassic to Middle Jurassic rifting in the Tethyan domain, followed by Middle to Late Jurassic spreading.

Hurricane Mountain Formation melange: history of Cambro-Ordovician accretion of the Boundary Mountains terrane within the northern Appalachian orthotectonic zone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boone, G.M.; Boudette, E.L.

1985-01-01

The Hurricane Mountain Formation (HMF) melange and associated ophiolitic and volcanogenic formations of Cambrian and lowermost Ordovician age bound the SE margin of the Precambrian Y (Helikian) Chain Lakes Massif in western Maine. HMF melange matrix, though weakly metamorphosed, contains a wide variety of exotic greenschist to amphibolite facies blocks as components of its polymictic assemblage, but blocks of high-grade cratonal rocks such as those of Chain Lakes or Grenville affinity are lacking. Formations of melange exposed in structural culminations of Cambrian and Ordovician rocks NE of the HMF in Maine and in the Fournier Group in New Brunswick aremore » lithologically similar and probably tectonically correlative with the HMF; taken together, they may delineate a common pre-Middle Ordovician tectonic boundary. The authors infer that the Hurricane Mountain and St. Daniel melange belts define the SE and NW margins of the Boundary Mountains accreted terrane (BMT), which may consist of cratonal basement of Chain Lakes affinity extending from eastern Gaspe (deBroucker and St. Julien, 1985) to north-central New Hampshire. The Laurentian continental margin, underlain by Grenville basement, underplated the NW margin of this terrane, marked by the SDF suture zone, in late Cambrian to early Ordovician time, while terranes marked by Cambrian to Tremadocian (.) lithologies dissimilar to the Boundary Mountains terrane were accreted to its outboard margin penecontemporaneously. The docking of the Boundary Mountains terrane and the initiation of its peripheral melanges are equated to the Penobscottian disturbance.« less

Defining Lithological Units by Cuttings, Core and Logging Data at Site C0009A in the Nankai Trough, Japan: IODP Expedition 319

NASA Astrophysics Data System (ADS)

Efimenko, N.; Schleicher, A. M.; Buchs, D. M.; Buret, C.; Kawabata, K.; Boutt, D. F.; Underwood, M.; Araki, E.; Byrne, T. B.; McNeill, L. C.; Saffer, D. M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Scientists, E.

2009-12-01

The use of cuttings as an alternative or addition to core material is broadly debated in on-shore and off-shore drilling expeditions. Expedition 319 is the first IODP based Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) project using the riser-drilling method to collect cutting and core samples for scientific studies. One major scientific objective for this site was to characterise the lithology and deformation history of the Kumano forearc basin sediments and its underlying units through comparison of (i) cuttings, (ii) core, (iii) measurements while drilling, and (iv) wireline logging data. Cuttings were retrieved from each 5 m intervals from 703.9 to 1604 m, and cores were recovered from 1509.7 to 1593.9 m below sea floor. As core availability was limited, the study of cuttings was a crucial step in improving our understanding of their potential and limits for lithostratigraphical interpretations compared to core. Mineralogical and chemical analysis of cuttings and core, wireline logging data, and gamma ray data from MWD were available to define four lithostratigraphic units. These units are composed of mud and mudstone with coarser silty and sandy interbeds, and volcanic ash/tuff. Consistency between unit boundaries determined from cuttings and those determined from log data is good in terms of depth, with typical mismatches of less than 10m. Three significant problems affecting the preservation of cuttings were (1) mixing of cuttings as they travel from the drill face to the surface, (2) alteration of natural mineral and structure signatures, and (3) possible contamination from natural clay minerals with the polymer/bentonite drill mud. These difficulties can be overcome in part through the analysis of cuttings of similar sizes (1-4 mm), guided by the analyses of bulk cuttings. A more accurate quantitative characterisation of cuttings through the use of digital imaging might improve the description of lithofacies. Although the quality of cuttings is affected by caving and drilling mud contamination, our results clearly indicate that cuttings retrieval is a viable alternative to coring in ocean drilling. However, to improve the precision of lithostratigraphical observations and interpretations in critical intervals, the study of cores is needed.

[High Precision Identification of Igneous Rock Lithology by Laser Induced Breakdown Spectroscopy].

PubMed

Wang, Chao; Zhang, Wei-gang; Yan, Zhi-quan

2015-09-01

In the field of petroleum exploration, lithology identification of finely cuttings sample, especially high precision identification of igneous rock with similar property, has become one of the geological problems. In order to solve this problem, a new method is proposed based on element analysis of Laser-Induced Breakdown Spectroscopy (LIBS) and Total Alkali versus Silica (TAS) diagram. Using independent LIBS system, factors influencing spectral signal, such as pulse energy, acquisition time delay, spectrum acquisition method and pre-ablation are researched through contrast experiments systematically. The best analysis conditions of igneous rock are determined: pulse energy is 50 mJ, acquisition time delay is 2 μs, the analysis result is integral average of 20 different points of sample's surface, and pre-ablation has been proved not suitable for igneous rock sample by experiment. The repeatability of spectral data is improved effectively. Characteristic lines of 7 elements (Na, Mg, Al, Si, K, Ca, Fe) commonly used for lithology identification of igneous rock are determined, and igneous rock samples of different lithology are analyzed and compared. Calibration curves of Na, K, Si are generated by using national standard series of rock samples, and all the linearly dependent coefficients are greater than 0.9. The accuracy of quantitative analysis is investigated by national standard samples. Element content of igneous rock is analyzed quantitatively by calibration curve, and its lithology is identified accurately by the method of TAS diagram, whose accuracy rate is 90.7%. The study indicates that LIBS can effectively achieve the high precision identification of the lithology of igneous rock.

Combined natural gamma ray spectral/litho-density measurements applied to complex lithologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quirein, J.A.; Gardner, J.S.; Watson, J.T.

1982-09-01

Well log data has long been used to provide lithological descriptions of complex formations. Historically, most of the approaches used have been restrictive because they assumed fixed, known, and distinct lithologies for specified zones. The approach described in this paper attempts to alleviate this restriction by estimating the ''probability of a model'' for the models suggested as most likely by the reservoir geology. Lithological variables are simultaneously estimated from response equations for each model and combined in accordance with the probability of each respective model. The initial application of this approach has been the estimation of calcite, quartz, and dolomitemore » in the presence of clays, feldspars, anhydrite, or salt. Estimations were made by using natural gamma ray spectra, photoelectric effect, bulk density, and neutron porosity information. For each model, response equations and parameter selections are obtained from the thorium vs potassium crossplot and the apparent matrix density vs apparent volumetric photoelectric cross section crossplot. The thorium and potassium response equations are used to estimate the volumes of clay and feldspar. The apparent matrix density and volumetric cross section response equations can then be corrected for the presence of clay and feldspar. A test ensures that the clay correction lies within the limits for the assumed lithology model. Results are presented for varying lithologies. For one test well, 6,000 feet were processed in a single pass, without zoning and without adjusting more than one parameter pick. The program recognized sand, limestone, dolomite, clay, feldspar, anhydrite, and salt without analyst intervention.« less

GIS representation of coal-bearing areas in Antarctica

USGS Publications Warehouse

Merrill, Matthew D.

2016-03-11

Understanding the distribution of coal-bearing geologic units in Antarctica provides information that can be used in sedimentary, geomorphological, paleontological, and climatological studies. This report is a digital compilation of information on Antarctica’s coal-bearing geologic units found in the literature. It is intended to be used in small-scale spatial geographic information system (GIS) investigations and as a visual aid in the discussion of Antarctica’s coal resources or in other coal-based geologic investigations. Instead of using spatially insignificant point markers to represent large coal-bearing areas, this dataset uses polygons to represent actual coal-bearing lithologic units. Specific locations of coal deposits confirmed from the literature are provided in the attribution for the coal-bearing unit polygons. Coal-sample-location data were used to confirm some reported coal-bearing geology. The age and extent of the coal deposits indicated in the literature were checked against geologic maps ranging from local scale at 1:50,000 to Antarctic continental scale at 1:5,000,000; if satisfactory, the map boundaries were used to generate the polygons for the coal-bearing localities.

Geologic map of the Cucamonga Peak 7.5' quadrangle, San Bernardino County, California

USGS Publications Warehouse

Morton, D.M.; Matti, J.C.; Digital preparation by Koukladas, Catherine; Cossette, P.M.

2001-01-01

a. This Readme; includes in Appendix I, data contained in fif_met.txt b. The same graphic as plotted in 2 above. (Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat pagesize setting influences map scale.) The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Miscellaneous Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U. S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially forest roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Cucamonga Peak 7.5’ topographic quadrangle in conjunction with the geologic map.

Geologic map of the Telegraph Peak 7.5' quadrangle, San Bernardino County, California

USGS Publications Warehouse

Morton, D.M.; Woodburne, M.O.; Foster, J.H.; Morton, Gregory; Cossette, P.M.

2001-01-01

a. This Readme; includes in Appendix I, data contained in fif_met.txt b. The same graphic as plotted in 2 above. Test plots have not produced 1:24,000-scale map sheets. Adobe Acrobat pagesize setting influences map scale. The Correlation of Map Units and Description of Map Units is in the editorial format of USGS Miscellaneous Investigations Series (I-series) maps but has not been edited to comply with I-map standards. Within the geologic map data package, map units are identified by standard geologic map criteria such as formation-name, age, and lithology. Even though this is an author-prepared report, every attempt has been made to closely adhere to the stratigraphic nomenclature of the U. S. Geological Survey. Descriptions of units can be obtained by viewing or plotting the .pdf file (3b above) or plotting the postscript file (2 above). If roads in some areas, especially forest roads that parallel topographic contours, do not show well on plots of the geologic map, we recommend use of the USGS Telegraph Peak 7.5’ topographic quadrangle in conjunction with the geologic map.

Big data integration for regional hydrostratigraphic mapping

NASA Astrophysics Data System (ADS)

Friedel, M. J.

2013-12-01

Numerical models provide a way to evaluate groundwater systems, but determining the hydrostratigraphic units (HSUs) used in devising these models remains subjective, nonunique, and uncertain. A novel geophysical-hydrogeologic data integration scheme is proposed to constrain the estimation of continuous HSUs. First, machine-learning and multivariate statistical techniques are used to simultaneously integrate borehole hydrogeologic (lithology, hydraulic conductivity, aqueous field parameters, dissolved constituents) and geophysical (gamma, spontaneous potential, and resistivity) measurements. Second, airborne electromagnetic measurements are numerically inverted to obtain subsurface resistivity structure at randomly selected locations. Third, the machine-learning algorithm is trained using the borehole hydrostratigraphic units and inverted airborne resistivity profiles. The trained machine-learning algorithm is then used to estimate HSUs at independent resistivity profile locations. We demonstrate efficacy of the proposed approach to map the hydrostratigraphy of a heterogeneous surficial aquifer in northwestern Nebraska.

THERMAL-INERTIA MAPPING IN VEGETATED TERRAIN FROM HEAT CAPACITY MAPPING MISSION SATELLITE DATA.

USGS Publications Warehouse

Watson, Ken; Hummer-Miller, Susanne

1984-01-01

Thermal-inertia data, derived from the Heat Capacity Mapping Mission (HCMM) satellite, were analyzed in areas of varying amounts of vegetation cover. Thermal differences which appear to correlate with lithologic differences have been observed previously in areas of substantial vegetation cover. However, the energy exchange occurring within the canopy is much more complex than that used to develop the methods employed to produce thermal-inertia images. Because adequate models are lacking at present, the interpretation is largely dependent on comparison, correlation, and inference. Two study areas were selected in the western United States: the Richfield, Utah and the Silver City, Arizona-New Mexico, 1 degree multiplied by 2 degree quadrangles. Many thermal-inertia highs were found to be associated with geologic-unit boundaries, faults, and ridges. Lows occur in valleys with residual soil cover.

La Peligrosa caldera (47° 15‧S, 71° 40‧W): A key event during the Jurassic ignimbrite flare-up in Southern Patagonia, Argentina

NASA Astrophysics Data System (ADS)

Sruoga, P.; Japas, M. S.; Salani, F. M.; Kleiman, L. E.

2014-01-01

Pyroclastic and lava vent-facies, from the Late Jurassic El Quemado Complex, are described at the southern Lake Ghío, in the Cordillera Patagónica Austral. Based on the comprehensive study of lithology and structures, the reconstruction of the volcanic architecture has been carried out. Four ignimbrites and one rhyolitic lava unit, affected by oblique-slip normal faults have been recognized. The evolution of La Peligrosa Caldera has been modeled in three different stages:1) initial collapse, consisting of a precursory downsag subsidence, related to a dilatational zone, which controlled the location of the caldera, 2) main collapse, with the emplacement of large volume crystal-rich ignimbrites and megabreccias, under a progressive subsidence controlled by a pull-apart structure related to a transtensional regime and 3) post-collapse, in which lava flows and associated domes were emplaced under an oblique-extensional regime. The caldera records a remarkable change from transtension to oblique extension, which may represent an important variation in regional deformation conditions during Jurassic times. La Peligrosa Caldera may be considered a key event to understand the eruptive mechanisms of the flare-up volcanism in the Chon Aike Silicic Province.

Geometry of miocene extensional deformation, lower Colorado River Region, Southeastern California and Southwestern Arizona: Evidence for the presence of a regional low-angle normal fault

NASA Technical Reports Server (NTRS)

Tosdal, R. M.; Sherrod, D. R.

1985-01-01

The geometry of Miocene extensional deformation, which changes along a 120 km-long, northeast-trending transect from the southestern Chocolate Mountains, southeastern California, to the Trigo and southern Dome Rock Mountains, southwestern Arizona is discussed. Based upon regional differences in the structural response to extension and estimated extensional strain, the transet can be divided into three northwesterly-trending structural domains. From southwest to northeast, these domains are: (1) southestern Chocolate-southernmost Trigo Mountains; (2) central to northern Trigo Mountains; and (3) Trigo Peaks-southern Dome Rock Mountains. All structures formed during the deformation are brittle in style; fault rocks are composed of gouge, cohesive gouge, and local microbreccia. In each structural domain, exposed lithologic units are composed of Mesozoic crystalline rocks unconformably overlain by Oligocene to Early Miocene volcanic and minor interbedded sedimentary rocks. Breccia, conglomerate, and sandstone deposited synchronously with regional extension locally overlie the volcanic rocks. Extensional deformation largely postdated the main phase of volcanic activity, but rare rhyolitic tuff and flows interbedded with the syndeformational clastic rocks suggest that deformation began during the waning stages of valcanism. K-Ar isotopic ages indicate that deformation occurred in Miocene time, between about 22 and m.y. ago.

Marine petroleum source rocks and reservoir rocks of the Miocene Monterey Formation, California, U.S.A

USGS Publications Warehouse

Isaacs, C.M.

1988-01-01

The Miocene Monterey Formation of California, a biogenous deposit derived mainly from diatom debris, is important both as a petroleum source and petroleum reservoir. As a source, the formation is thought to have generated much of the petroleum in California coastal basins, which are among the most prolific oil provinces in the United States. Oil generated from the Monterey tends to be sulfur-rich and heavy (<20° API), and has chemical characteristics that more closely resemble immature source extracts than "normal" oil. Thermal-maturity indicators in Monterey kerogens appear to behave anomalously, and several lines of evidence indicate that the oil is generated at lower than expected levels of organic metamorphism. As a reservoir, the Monterey is important due both to conventional production from permeable sandstone beds and to fracture production from fine-grained rocks with low matrix permeability. Fractured reservoirs are difficult to identify, and conventional well-log analysis has not proven to be very useful in exploring for and evaluating these reservoirs. Lithologically similar rocks are broadly distributed throughout the Circum-Pacific region, but their petroleum potential is unlikely to be realized without recognition of the distinctive source and reservoir characteristics of diatomaceous strata and their diagenetic equivalents.

Fractal density modeling of crustal heterogeneity from the KTB deep hole

NASA Astrophysics Data System (ADS)

Chen, Guoxiong; Cheng, Qiuming

2017-03-01

Fractal or multifractal concepts have significantly enlightened our understanding of crustal heterogeneity. Much attention has focused on 1/f scaling natures of physicochemical heterogeneity of Earth crust from fractal increment perspective. In this study, fractal density model from fractal clustering point of view is used to characterize the scaling behaviors of heterogeneous sources recorded at German Continental Deep Drilling Program (KTB) main hole, and of special contribution is the local and global multifractal analysis revisited by using Haar wavelet transform (HWT). Fractal density modeling of mass accumulation generalizes the unit of rock density from integer (e.g., g/cm3) to real numbers (e.g., g/cmα), so that crustal heterogeneities with respect to source accumulation are quantified by singularity strength of fractal density in α-dimensional space. From that perspective, we found that the bulk densities of metamorphic rocks exhibit fractal properties but have a weak multifractality, decreasing with the depth. The multiscaling natures of chemical logs also have been evidenced, and the observed distinct fractal laws for mineral contents are related to their different geochemical behaviors within complex lithological context. Accordingly, scaling distributions of mineral contents have been recognized as a main contributor to the multifractal natures of heterogeneous density for low-porosity crystalline rocks. This finally allows us to use de Wijs cascade process to explain the mechanism of fractal density. In practice, the proposed local singularity analysis based on HWT is suggested as an attractive high-pass filtering to amplify weak signatures of well logs as well as to delineate microlithological changes.

The deeper structure of the southern Dead Sea basin derived from neural network analysis of velocity and attenuation tomography

NASA Astrophysics Data System (ADS)

Braeuer, Benjamin; Haberland, Christian; Bauer, Klaus; Weber, Michael

2014-05-01

The Dead Sea basin is a pull-apart basin at the Dead Sea transform fault, the boundary between the African and the Arabian plates. Though the DSB has been studied for a long time, the available knowledge - based mainly on surface geology, drilling and seismic reflection surveys - gives only a partial picture of its shallow structure. Therefore, within the framework of the international DESIRE (DEad Sea Integrated REsearch) project, a dense temporary local seismological network was operated in the southern Dead Sea area. Within 18 month of recording 650 events were detected. In addition to an already published tomography study revealing the distribution of P velocities and the Vp/Vs ratios a 2D P-wave attenuation tomography (parameter Qp) was performed. The neural network technique of Self-organizing maps (SOM) is used for the joint interpretation of these three parameters (Vp, Vp/Vs, Qp). The resulting clusters in the petrophysical parameter space are assigned to the main lithological units below the southern part of the Dead Sea basin: (1) The basin sediments characterized by strong attenuation, high vp/vs ratios and low P velocities. (2) The pre-basin sediments characterized by medium to strong attenuation, low Vp/Vs ratios and medium P velocities. (3) The basement characterized by low to moderate attenuation, medium vp/vs ratios and high P velocities. Thus, the asymmetric southern Dead Sea basin is filled with basin sediments down to depth of 7 to 12 km. Below the basin sediments, the pre-basin sediments are extending to a depth between 13 and 18 km.

HCMM: Soil moisture in relation to geologic structure and lithology, northern California. [Sacramento Valley, California

NASA Technical Reports Server (NTRS)

Rich, E. I. (Principal Investigator)

1980-01-01

The author has identified the following significant results. Empirical observations on the ground and examination of aerial color IR photographs indicate that in grassland terrain, the vegetation overlying sandstone tends to become less vigorous sooner in the late spring season than does the area overlain by an adjacent shale unit. The reverse relationship obtains in the fall. These relationships are thought to be a reflection of the relative porosity of each of the units and hence of their ability to retain or lose soil moisture. A comparison of the optically enlarged day and nite IR imagery of the Late Mesozoic interbedded sandstone and shale units along the western margin of the Sacramento Valley, California, taken at seasonally critical times of the year (late spring/early summer and late fall/early winter) reveals subtle seasonal variations of graytone which tend to support the empirical observations after consideration of Sun angle and azimuth, and the internal consistency of the data on each set of satellite imagery.

Preliminary geologic map of the Oat Mountain 7.5' quadrangle, Southern California: a digital database

USGS Publications Warehouse

Yerkes, R.F.; Campbell, Russell H.

1995-01-01

This database, identified as "Preliminary Geologic Map of the Oat Mountain 7.5' Quadrangle, southern California: A Digital Database," has been approved for release and publication by the Director of the USGS. Although this database has been reviewed and is substantially complete, the USGS reserves the right to revise the data pursuant to further analysis and review. This database is released on condition that neither the USGS nor the U. S. Government may be held liable for any damages resulting from its use. This digital map database is compiled from previously published sources combined with some new mapping and modifications in nomenclature. The geologic map database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U. S. Geological Survey. For detailed descriptions of the units, their stratigraphic relations and sources of geologic mapping consult Yerkes and Campbell (1993). More specific information about the units may be available in the original sources.

Thoughts Regarding the Dimensions of Faults at Rainier and Aqueduct Mesas, Nye County, Nevada, Based on Surface and Underground Mapping

DOE Office of Scientific and Technical Information (OSTI.GOV)

Drellack, S.L.; Prothro, L.B.; Townsend, M.J.

2011-02-01

The geologic setting and history, along with observations through 50 years of detailed geologic field work, show that large-displacement (i.e., greater than 30 meters of displacement) syn- to post-volcanic faults are rare in the Rainier Mesa area. Faults observed in tunnels and drill holes are mostly tight, with small displacements (most less than 1.5 meters) and small associated damage zones. Faults are much more abundant in the zeolitized tuffs than in the overlying vitric tuffs, and there is little evidence that faults extend downward from the tuff section through the argillic paleocolluvium into pre-Tertiary rocks. The differences in geomechanical characteristicsmore » of the various tuff lithologies at Rainier Mesa suggest that most faults on Rainer Mesa are limited to the zeolitic units sandwiched between the overlying vitric bedded tuffs and the underlying pre-Tertiary units (lower carbonate aquifer–3, lower clastic confining unit–1, and Mesozoic granite confining unit).« less

Characterization of Stream Channel Evolution Due to Extensional Tectonics Along the Western Margin of North Boulder Basin (Bull Mountain), SW Montana with the Use of Geologic Mapping and Thermochronologic (U-Th/He) Dating.

NASA Astrophysics Data System (ADS)

Cataldo, K.; Douglas, B. J.; Yanites, B.

2017-12-01

Landscape response to active tectonics, such as fault motion or regional uplift, can be recorded in river profiles as changes in slope (i.e. knickpoints) or topography. North Boulder basin region (SW Montana), experienced two separate phases of extension, from 45 - 35 Ma and again beginning 14 Ma to the present, producing basin-and-range style fault-blocks. Focusing on the Bull Mountain region, located on the western margin of the North Boulder basin, data is collected to test the hypothesis that Bull Mountain is located on the hanging wall of a half-graben. Our objective is to elucidate the active tectonics of the study area within a regional context by utilizing river profile analysis and thermochronometric data. High-resolution (< 5cm) river profile data is obtained from five of the main tributaries of Bull Mountain. Comprehensive geologic mapping along the main tributaries and topographic highs of the region allowed for the identification and measurement of knickpoints, composition of detailed lithologic descriptions, and analysis of key structural features. The absence of knickpoints within the four tributaries mapped on east Bull Mountain are consistent with a lack of tectonic activity. In contrast, Dearborn Creek, on western Bull Mountain, is located along an active normal fault and presents several knickpoints. Geologic mapping confirms that the primary lithologies of the region belong to the Elkhorn Mountain Volcanics. At lower elevations, there are massive plutonic intrusions of Quartz Monzonite and Diorite, both constituents of the Boulder batholith. These lithologies contain minerals suited for low-temperature thermochronology (U-Th/He) to constrain the timing of tectonic activity (i.e. uplift and exhumation) and erosion rates in the region. High-resolution stream profiles and a 10m DEM are used to delineate watersheds and produce steepness and concavity maps of major tributaries to investigate changes in slope or topography. The effects of extensional tectonic events can reshape drainage patterns of streams and their distribution of water, which is an important commodity in SW Montana for ranchers and farmers. Thus, the ability to discern the probability of recurring tectonic events and the effects on the regional watersheds, could help facilitate solutions before these events take place.

New data on the lithology of coastal facies of the Turtas formation (Upper Oligocene, Southwestern Siberia)

NASA Astrophysics Data System (ADS)

Smirnov, P. V.; Konstantinov, A. O.; Aleksandrova, G. N.; Kuzmina, O. B.; Shurygin, B. N.

2017-08-01

Peculiarities of the material composition and microstructure of coastal facies of Turtas Lake-Sea were studied in its marginal southwestern part for the first time. Interpretation of the lithological data showed that the deposits considered were formed under the conditions of a slightly saline basin and nearby full-flow river network. Based on the lithological, geochemical, and micropaleontological studies of clay-siliceous rocks of the Lower Turtas Formation (the boundary zone between the Tyumen and Sverdlovsk regions), additional support for the freshwater lake regime of the Late Oligocene Turtas basin is given.

Apollo 16 Evolved Lithology Sodic Ferrogabbro

NASA Technical Reports Server (NTRS)

Zeigler, Ryan; Jolliff, B. L.; Korotev, R. L.

2014-01-01

Evolved lunar igneous lithologies, often referred to as the alkali suite, are a minor but important component of the lunar crust. These evolved samples are incompatible-element rich samples, and are, not surprisingly, most common in the Apollo sites in (or near) the incompatible-element rich region of the Moon known as the Procellarum KREEP Terrane (PKT). The most commonly occurring lithologies are granites (A12, A14, A15, A17), monzogabbro (A14, A15), alkali anorthosites (A12, A14), and KREEP basalts (A15, A17). The Feldspathic Highlands Terrane is not entirely devoid of evolved lithologies, and rare clasts of alkali gabbronorite and sodic ferrogabbro (SFG) have been identified in Apollo 16 station 11 breccias 67915 and 67016. Curiously, nearly all pristine evolved lithologies have been found as small clasts or soil particles, exceptions being KREEP basalts 15382/6 and granitic sample 12013 (which is itself a breccia). Here we reexamine the petrography and geochemistry of two SFG-like particles found in a survey of Apollo 16 2-4 mm particles from the Cayley Plains 62283,7-15 and 62243,10-3 (hereafter 7-15 and 10-3 respectively). We will compare these to previously reported SFG samples, including recent analyses on the type specimen of SFG from lunar breccia 67915.

Mineral and Lithology Mapping of Drill Core Pulps Using Visible and Infrared Spectrometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, G. R., E-mail: G.Taylor@unsw.edu.au

2000-12-15

A novel approach for using field spectrometry for determining both the mineralogy and the lithology of drill core pulps (powders) is developed and evaluated. The methodology is developed using material from a single drillhole through a mineralized sequence of rocks from central New South Wales. Mineral library spectra are used in linear unmixing routines to determine the mineral abundances in drill core pulps that represent between 1 m and 3 m of core. Comparison with X-Ray Diffraction (XRD) analyses shows that for most major constituents, spectrometry provides an estimate of quantitative mineralogy that is as reliable as that provided bymore » XRD. Confusion between the absorption features of calcite and those of chlorite causes the calcite contents determined by spectrometry to be unreliable. Convex geometry is used to recognize the spectra of those samples that are extreme and are representative of unique lithologies. Linear unmixing is used to determine the abundance of these lithologies in each drillhole sample and these abundances are used to interpret the geology of the drillhole. The interpreted geology agrees well with conventional drillhole logs of the visible geology and photographs of the split core. The methods developed provide a quick and cost-effective way of determining the lithology and alteration mineralogy of drill core pulps.« less

AnalyzeHOLE - An Integrated Wellbore Flow Analysis Tool

USGS Publications Warehouse

Halford, Keith

2009-01-01

Conventional interpretation of flow logs assumes that hydraulic conductivity is directly proportional to flow change with depth. However, well construction can significantly alter the expected relation between changes in fluid velocity and hydraulic conductivity. Strong hydraulic conductivity contrasts between lithologic intervals can be masked in continuously screened wells. Alternating intervals of screen and blank casing also can greatly complicate the relation between flow and hydraulic properties. More permeable units are not necessarily associated with rapid fluid-velocity increases. Thin, highly permeable units can be misinterpreted as thick and less permeable intervals or not identified at all. These conditions compromise standard flow-log interpretation because vertical flow fields are induced near the wellbore. AnalyzeHOLE, an integrated wellbore analysis tool for simulating flow and transport in wells and aquifer systems, provides a better alternative for simulating and evaluating complex well-aquifer system interaction. A pumping well and adjacent aquifer system are simulated with an axisymmetric, radial geometry in a two-dimensional MODFLOW model. Hydraulic conductivities are distributed by depth and estimated with PEST by minimizing squared differences between simulated and measured flows and drawdowns. Hydraulic conductivity can vary within a lithology but variance is limited with regularization. Transmissivity of the simulated system also can be constrained to estimates from single-well, pumping tests. Water-quality changes in the pumping well are simulated with simple mixing models between zones of differing water quality. These zones are differentiated by backtracking thousands of particles from the well screens with MODPATH. An Excel spreadsheet is used to interface the various components of AnalyzeHOLE by (1) creating model input files, (2) executing MODFLOW, MODPATH, PEST, and supporting FORTRAN routines, and (3) importing and graphically displaying pertinent results.

Geochemical provenance of Florida basement components

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heatherington, A.L.; Mueller, P.A.; Dallmeyer, R.D.

1993-03-01

The pre-Cretaceous basement of Florida is generally considered to be exotic with respect to Proterozoic Laurentia. Paleontologic and paleomagnetic evidence have suggested a Gondwanan provenance for the Floridan basement, as either a peri-Gondwanide terrane or as a rifted block of the West African craton. The report of generally similar lithologic sequences and a record of similar Ar-Ar cooling ages in some Floridan and West African lithologic units has led to very specific correlations between these units. U-Pb, Sm-Nd, and Rb-Sr geochronologic studies as well as isotopic and elemental abundance data have been used to evaluate the validity of these correlations.more » Results indicate: (1) geochemical similarities between volcanic rocks of northeastern Florida and a Pan-African metavolcanic sequence (Niokola-Koba group) exposed in Senegal; (2) an absence of a Grenvillian-age (i.e., Laurentian) component in zircons separated from a Paleozoic Suwanee basin sandstone; and (3) whole-rock Sm-Nd and U-Pb zircon evidence for an Archean ([approximately]3.0 Ga) component in the neo-Proterozoic Osceola granitoid(s). Although silicic rocks from throughout Florida have Nd model ages (T[sub DM]) that are predominantly Grenvillian (1.1--1.4 Ga), the absence of a Grenvillian component in zircons separated from granite and sandstone suggests that the model ages represent a mixture of older and younger components. Overall, the evidence for Birimian ([approximately]2.1 Ga) and Liberian ([approximately]3.0 Ga) age components in the Florida basement are consistent with its origin as a rifted block of cratonic Gondwana. In addition to demonstrating a strong affinity between the Florida basement and cratonic West Africa/northern South America, these data provide a basis for comparison with other circum-Atlantic terranes traditionally described as Avalonian/Cadomian, etc.« less

Periglacial morphogenesis in the Paris basin: insight from geophysical survey and consequences for the fate of soil pollution

NASA Astrophysics Data System (ADS)

Thiry, Médard; van Oort, Folkert; Thiesson, Julien; Van Vliet-Lanoe, Brigitte

2013-09-01

Geophysical survey by Automatic Resistivity Profiling (ARP©) system of the Pierrelaye-Bessancourt area revealed remarkable conductive polygon patterns of 20- to 30-m diameter detected between 0.5- and 1.7-m depth. Trenches dug down to the limestone substrate allowed detailing of the pedological and lithological units that compose such polygonal features. The patterns are formed by greenish glauconite and carbonated sand hollows where clay-rich pedological horizons bend downward, forming narrow tongs extending up to 2- to 3-m depth. Such structures were interpreted as a buried polygonal ice-wedge network (thermokarst depressions). Geometrical relationships between the lithological units and consecutive erosional surfaces allowed the identification of successive landscape events and a landscape chronology. The sequence started during the Saalian glaciation with (1) the development of patterned grounds by thermokarstic cryoturbation; (2) the consecutive deflation/erosion during post-permafrost aridity; (3) the loess and eolian sand deposits; (4) the weathering of the former deposits with development of pedogenic horizons during the Eemian interglacial; (5) the recurrent cryoturbation and thermal cracking leading to infolding of the pedogenic horizons during the Pleniglacial optimum (Weichselian); and finally (5) the erosion that levelled the periglacial microreliefs, most probably during the last glacial stage (Weichselian), leading to the modern landscape. In this agricultural area, urban waste water has been spread for more than 100 years by flooding irrigation for food crop production and has led to high levels of metal pollution in the surface horizons of the soils. The polygonal cryogenic structures have major impacts on soil hydrology and dispersion/distribution of heavy metals toward the geological substrate. Such structures are essential to consider when conceiving proposals for future soil management of this polluted area.

Ejecta distribution patterns at Meteor Crater, Arizona: On the applicability of lithologic end-member deconvolution for spaceborne thermal infrared data of Earth and Mars

NASA Astrophysics Data System (ADS)

Ramsey, Michael S.

2002-08-01

A spectral deconvolution using a constrained least squares approach was applied to airborne thermal infrared multispectral scanner (TIMS) data of Meteor Crater, Arizona. The three principal sedimentary units sampled by the impact were chosen as end-members, and their spectra were derived from the emissivity images. To validate previous estimates of the erosion of the near-rim ejecta, the model was used to identify the areal extent of the reworked material. The outputs of the algorithm reveal subtle mixing patterns in the ejecta, identified larger ejecta blocks, and were used to further constrain the volume of Coconino Sandstone present in the vicinity of the crater. The availability of the multialtitude data set also provided a means to examine the effects of resolution degradation and quantify the subsequent errors on the model. These data served as a test case for the use of image-derived lithologic end-members at various scales, which is critical for examining thermal infrared data of planetary surfaces. The model results indicate that the Coconino Ss. reworked ejecta is detectable over 3 km from the crater. This was confirmed by field sampling within the primary ejecta field and wind streak. The areal distribution patterns of this unit imply past erosion and subsequent sediment transport that was low to moderate compared with early studies and therefore places further constraints on the ejecta degradation of Meteor Crater. It also provides an important example of the analysis that can be performed on thermal infrared data currently being returned from Earth orbit and expected from Mars in 2002.

Wellsite, laboratory, and mathematical techniques for determining sorbed gas content of coals and gas shales utilizing well cuttings

USGS Publications Warehouse

Newell, K.D.

2007-01-01

Drill cuttings can be used for desorption analyses but with more uncertainty than desorption analyses done with cores. Drill cuttings are not recommended to take the place of core, but in some circumstances, desorption work with cuttings can provide a timely and economic supplement to that of cores. The mixed lithologic nature of drill cuttings is primarily the source of uncertainty in their analysis for gas content, for it is unclear how to apportion the gas generated from both the coal and the dark-colored shale that is mixed in usually with the coal. In the Western Interior Basin Coal Basin in eastern Kansas (Pennsylvanian-age coals), dark-colored shales with normal (??? 100 API units) gamma-ray levels seem to give off minimal amounts of gas on the order of less than five standard cubic feet per ton (scf/ton). In some cuttings analyses this rule of thumb for gas content of the shale is adequate for inferring the gas content of coals, but shales with high-gamma-ray values (>150 API units) may yield several times this amount of gas. The uncertainty in desorption analysis of drill cuttings can be depicted graphically on a diagram identified as a "lithologic component sensitivity analysis diagram." Comparison of cuttings desorption results from nearby wells on this diagram, can sometimes yield an unique solution for the gas content of both a dark shale and coal mixed in a cuttings sample. A mathematical solution, based on equating the dry, ash-free gas-contents of the admixed coal and dark-colored shale, also yields results that are correlative to data from nearby cores. ?? 2007 International Association for Mathematical Geology.

Application of logistic regression for landslide susceptibility zoning of Cekmece Area, Istanbul, Turkey

NASA Astrophysics Data System (ADS)

Duman, T. Y.; Can, T.; Gokceoglu, C.; Nefeslioglu, H. A.; Sonmez, H.

2006-11-01

As a result of industrialization, throughout the world, cities have been growing rapidly for the last century. One typical example of these growing cities is Istanbul, the population of which is over 10 million. Due to rapid urbanization, new areas suitable for settlement and engineering structures are necessary. The Cekmece area located west of the Istanbul metropolitan area is studied, because the landslide activity is extensive in this area. The purpose of this study is to develop a model that can be used to characterize landslide susceptibility in map form using logistic regression analysis of an extensive landslide database. A database of landslide activity was constructed using both aerial-photography and field studies. About 19.2% of the selected study area is covered by deep-seated landslides. The landslides that occur in the area are primarily located in sandstones with interbedded permeable and impermeable layers such as claystone, siltstone and mudstone. About 31.95% of the total landslide area is located at this unit. To apply logistic regression analyses, a data matrix including 37 variables was constructed. The variables used in the forwards stepwise analyses are different measures of slope, aspect, elevation, stream power index (SPI), plan curvature, profile curvature, geology, geomorphology and relative permeability of lithological units. A total of 25 variables were identified as exerting strong influence on landslide occurrence, and included by the logistic regression equation. Wald statistics values indicate that lithology, SPI and slope are more important than the other parameters in the equation. Beta coefficients of the 25 variables included the logistic regression equation provide a model for landslide susceptibility in the Cekmece area. This model is used to generate a landslide susceptibility map that correctly classified 83.8% of the landslide-prone areas.

Bulk Oxygen-Isotope Compositions of Different Lithologies in Sutter's Mill

NASA Astrophysics Data System (ADS)

Ziegler, K.; Garvie, L. A. J.

2013-09-01

We correlate mineralogy data with bulk oxygen-isotope data of the clay-rich and the ol-rich lithologies in order to assess the possibility of more than one parent material, and the possibility of different alteration environments on the parent body.

Lithologic characterization of active ITD aggregate sources and implications for aggregate quality.

DOT National Transportation Integrated Search

2014-03-01

Aggregate from 40 material sources across Idaho were sampled and the lithologies identified quantitatively. Aggregate compositions are compared with commercial AASHTO T 303 and ASTM C1293 results and the geologic map of Idaho to identify those rock t...

Adjustment of geochemical background by robust multivariate statistics

USGS Publications Warehouse

Zhou, D.

1985-01-01

Conventional analyses of exploration geochemical data assume that the background is a constant or slowly changing value, equivalent to a plane or a smoothly curved surface. However, it is better to regard the geochemical background as a rugged surface, varying with changes in geology and environment. This rugged surface can be estimated from observed geological, geochemical and environmental properties by using multivariate statistics. A method of background adjustment was developed and applied to groundwater and stream sediment reconnaissance data collected from the Hot Springs Quadrangle, South Dakota, as part of the National Uranium Resource Evaluation (NURE) program. Source-rock lithology appears to be a dominant factor controlling the chemical composition of groundwater or stream sediments. The most efficacious adjustment procedure is to regress uranium concentration on selected geochemical and environmental variables for each lithologic unit, and then to delineate anomalies by a common threshold set as a multiple of the standard deviation of the combined residuals. Robust versions of regression and RQ-mode principal components analysis techniques were used rather than ordinary techniques to guard against distortion caused by outliers Anomalies delineated by this background adjustment procedure correspond with uranium prospects much better than do anomalies delineated by conventional procedures. The procedure should be applicable to geochemical exploration at different scales for other metals. ?? 1985.

Increased river alkalinization in the Eastern U.S.

PubMed

Kaushal, Sujay S; Likens, Gene E; Utz, Ryan M; Pace, Michael L; Grese, Melissa; Yepsen, Metthea

2013-09-17

The interaction between human activities and watershed geology is accelerating long-term changes in the carbon cycle of rivers. We evaluated changes in bicarbonate alkalinity, a product of chemical weathering, and tested for long-term trends at 97 sites in the eastern United States draining over 260,000 km(2). We observed statistically significant increasing trends in alkalinity at 62 of the 97 sites, while remaining sites exhibited no significant decreasing trends. Over 50% of study sites also had statistically significant increasing trends in concentrations of calcium (another product of chemical weathering) where data were available. River alkalinization rates were significantly related to watershed carbonate lithology, acid deposition, and topography. These three variables explained ~40% of variation in river alkalinization rates. The strongest predictor of river alkalinization rates was carbonate lithology. The most rapid rates of river alkalinization occurred at sites with highest inputs of acid deposition and highest elevation. The rise of alkalinity in many rivers throughout the Eastern U.S. suggests human-accelerated chemical weathering, in addition to previously documented impacts of mining and land use. Increased river alkalinization has major environmental implications including impacts on water hardness and salinization of drinking water, alterations of air-water exchange of CO2, coastal ocean acidification, and the influence of bicarbonate availability on primary production.

Cyclicity in Upper Mississippian Bangor Limestone, Blount County, Alabama

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bronner, R.L.

1988-01-01

The Upper Mississippian (Chesterian) Bangor Limestone in Alabama consists of a thick, complex sequence of carbonate platform deposits. A continuous core through the Bangor on Blount Mountain in north-central Alabama provides the opportunity to analyze the unit for cyclicity and to identify controls on vertical facies sequence. Lithologies from the core represent four general environments of deposition: (1) subwave-base, open marine, (2) shoal, (3) lagoon, and (4) peritidal. Analysis of the vertical sequence of lithologies in the core indicates the presence of eight large-scale cycles dominated by subtidal deposits, but defined on the basis of peritidal caps. These large-scale cyclesmore » can be subdivided into 16 small-scale cycles that may be entirely subtidal but illustrate upward shallowing followed by rapid deepening. Large-scale cycles range from 33 to 136 ft thick, averaging 68 ft; small-scale cycles range from 5 to 80 ft thick and average 34 ft. Small-scale cycles have an average duration of approximately 125,000 years, which is compatible with Milankovitch periodicity. The large-scale cycles have an average duration of approximately 250,000 years, which may simply reflect variations in amplitude of sea level fluctuation or the influence of tectonic subsidence along the southeastern margin of the North American craton.« less

Feast to famine: Sediment supply control on Laramide basin fill

NASA Astrophysics Data System (ADS)

Carroll, Alan R.; Chetel, Lauren M.; Elliot Smith, M.

2006-03-01

Erosion of Laramide-style uplifts in the western United States exerted an important first-order influence on Paleogene sedimentation by controlling sediment supply rates to adjacent closed basins. During the latest Cretaceous through Paleocene, these uplifts exposed thick intervals of mud-rich Upper Cretaceous foreland basin fill, which was quickly eroded and redeposited. Cretaceous sedimentary lithologies dominate Paleocene conglomerate clast compositions, and the volume of eroded foreland basin strata is approximately twice the volume of preserved Paleocene basin fill. As a result of this sediment oversupply, clastic alluvial and paludal facies dominate Paleocene strata, and are associated with relatively shallow and ephemeral freshwater lake facies. In contrast, large, long-lived, carbonate-producing lakes occupied several of the basins during the Eocene. Basement-derived clasts (granite, quartzite, and other metamorphic rocks) simultaneously became abundant in lower Eocene conglomerate. We propose that Eocene lakes developed primarily due to exposure of erosion-resistant lithologies within cores of Laramide uplifts. The resultant decrease in erosion rate starved adjacent basins of sediment, allowing the widespread and prolonged deposition of organic-rich lacustrine mudstone. These observations suggest that geomorphic evolution of the surrounding landscape should be considered as a potentially important influence on sedimentation in many other interior basins, in addition to more conventionally interpreted tectonic and climatic controls.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huntsman, J.R.

Eastern slate belt lithologies in the central Flowers quadrangle consist of metavolcanic and metasedimentary rocks. Very fine-grained quartz-white mica phyllite containing narrow, discontinuous layers of thinly laminated chlorite-rich rock and fine-grained, thinly layered, feldspar crystal felsic metatuff comprise the dominant, mappable units consistent across the quadrangle. An increase in grain size accompanied by a replacement of chlorite-rich lithologies with biotite [+-] garnet assemblages suggest metamorphic grade increases towards the western half of the quadrangle (quartz-muscovite schist and biotite-quartz-muscovite-feldspar gneiss). An early, northeast-trending foliation (050[degree] to 060[degree]) dipping moderately to steeply southeast persists across the quadrangle and is axial planar tomore » tight to isoclinal, recumbent to moderately inclined folds. Later non-coaxial folding produced steeply plunging, northerly trending (000[degree] to 020[degree]), open, asymmetric structures verging towards the east/southeast. Shear zones formed locally along the axial trend of these later folds and produced protomylonitic to mylonitic ( ) fabrics. Map patterns and cross-sectional interpretations are best explained by modification of zig-zag fold interference patterns. Thin section examination reveals garnets growing across the early axial planar foliation. The observed increase in metamorphic grade across the quadrangle matches the regional Alleghanian prograde event and constrains relative timing of observed deformational fabrics. Noticeably absent are regional, late-stage upright folds.« less

Landslides susceptibility mapping at Gunung Ciremai National Park

NASA Astrophysics Data System (ADS)

Faizin; Nur, Bambang Azis

2018-02-01

In addition to agriculture, tourism became one of primary economic income for communities around Mount Ciremai, West, Java. Unfortunately, the landscape of West Java has many potential causes to disasters, mainly landslides. Mapping of disaster susceptibility area is needed as a consideration of tourism planning. The study was conducted in Gunung Ciremai National Park, West Java. This paper propose a methodology to map landslides susceptibilities based on spatial data. Using Geographic Information System tools, several environmental parameters such as slope, land use, elevation, and lithology are scored to build a landslide susceptibility map. Then, susceptibility map is overlaid with Utilization Zone.

Geologic Structures in Crater Walls on Vesta

NASA Technical Reports Server (NTRS)

Mittlefehldt, David W.; Beck, A. W.; Ammannito, E.; Carsenty, U.; DeSanctis, M. C.; LeCorre, L.; McCoy, T. J.; Reddy, V.; Schroeder, S. E.

2012-01-01

The Framing Camera (FC) on the Dawn spacecraft has imaged most of the illuminated surface of Vesta with a resolution of apporpx. 20 m/pixel through different wavelength filters that allow for identification of lithologic units. The Visible and Infrared Mapping Spectrometer (VIR) has imaged the surface at lower spatial resolution but high spectral resolution from 0.25 to 5 micron that allows for detailed mineralogical interpretation. The FC has imaged geologic structures in the walls of fresh craters and on scarps on the margin of the Rheasilvia basin that consist of cliff-forming, competent units, either as blocks or semi-continuous layers, hundreds of m to km below the rims. Different units have different albedos, FC color ratios and VIR spectral characteristics, and different units can be juxtaposed in individual craters. We will describe different examples of these competent units and present preliminary interpretations of the structures. A common occurrence is of blocks several hundred m in size of high albedo (bright) and low albedo (dark) materials protruding from crater walls. In many examples, dark material deposits lie below coherent bright material blocks. In FC Clementine color ratios, bright material is green indicating deeper 1 m pyroxene absorption band. VIR spectra show these to have deeper and wider 1 and 2 micron pyroxene absorption bands than the average vestan surface. The associated dark material has subdued pyroxene absorption features compared to the average vestan surface. Some dark material deposits are consistent with mixtures of HED materials with carbonaceous chondrites. This would indicate that some dark material deposits in crater walls are megabreccia blocks. The same would hold for bright material blocks found above them. Thus, these are not intact crustal units. Marcia crater is atypical in that the dark material forms a semi-continuous, thin layer immediately below bright material. Bright material occurs as one or more layers. In one region, there is an apparent angular unconformity between the bright material and the dark material where bright material layers appear to be truncated against the underlying dark layer. One crater within the Rheasilvia basin contains two distinct types of bright materials outcropping on its walls, one like that found elsewhere on Vesta and the other an anomalous block 200 m across. This material has the highest albedo; almost twice that of the vestan average. Unlike all other bright materials, this block has a subdued 1 micron pyroxene absorption band in FC color ratios. These data indicate that this block represents a distinct vestan lithology that is rarely exposed.

Contingency table analysis of pebble lithology and roundness: A case study of Huangshui River, China and comparison to rivers in the Rocky Mountains, USA

USGS Publications Warehouse

Miao, X.; Lindsey, D.A.; Lai, Z.; Liu, Xiuying

2010-01-01

Contingency table analysis of pebble lithology and roundness is an effective way to identify the source terrane of a drainage basin and to distinguish changes in basin size, piracy, tectonism, and other events. First, the analysis to terrace gravel deposited by the Huangshui River, northeastern Tibet Plateau, China, shows statistically contrasting pebble populations for the oldest terrace (T7, Dadongling, 1.2. Ma) and the youngest terraces (T0-T3, ?. 0.15. Ma). Two fluvial processes are considered to explain the contrast in correlation between lithology and roundness in T7 gravel versus T0-T3 gravel: 1) reworking of T7 gravel into T0-T3 gravel and 2) growth in the size of the river basin between T7 and T0-T3 times. We favor growth in basin size as the dominant process, from comparison of pebble counts and contingency tables. Second, comparison of results from Huangshui River of China to three piedmont streams of the Rocky Mountains, USA highlights major differences in source terrane and history. Like Rocky Mountain piedmont gravel from Colorado examples, the Huangshui gravels show a preference (observed versus expected frequency) for rounded granite. But unlike Rocky Mountain gravel, Huangshui gravel shows a preference for angular quartzite and for rounded sandstone. In conclusion, contrasting behavior of lithologies during transport, not always apparent in raw pebble counts, is readily analyzed using contingency tables to identify the provenance of individual lithologies, including recycled clasts. Results of the analysis may help unravel river history, including changes in basin size and lithology. ?? 2009.

Experimental Constraints on the Cr Content, Oxygen Fugacity, and Petrogenesis of EETA79001 Lithology A

NASA Technical Reports Server (NTRS)

Herd, C. D. K.; Jones, J. H.; Papike, J. J.

2000-01-01

Experiments involving the composition of the groundmass of EETA79001 Lithology A constrain the Cr content of the melt and the oxygen fugacity, and suggest that overgrowth of olivine and pyroxene from the groundmass onto xenocrysts has occurred.

Soda Lake Well Lithology Data and Geologic Cross-Sections

DOE Data Explorer

Faulds, James E.

2013-12-31

Comprehensive catalogue of drill‐hole data in spreadsheet, shapefile, and Geosoft database formats. Includes XYZ locations of well heads, year drilled, type of well, operator, total depths, well path data (deviations), lithology logs, and temperature data. Plus, 13 cross‐sections in Adobe Illustrator format.

Fallon FORGE Well Lithologies

DOE Data Explorer

Doug Blankenship

2016-03-01

x,y,z text file of the downhole lithologic interpretations in the wells in and around the Fallon FORGE site. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

Multiseasonal and geobotanical approach in remote detection of greisenization areas in the Serra da Pedra Branca Granite, Goias State, Brazil

NASA Technical Reports Server (NTRS)

Parada, N. D. J. (Principal Investigator); Almeidafilho, R.

1983-01-01

Multiseasonal analysis of LANDSAT multispectral images in CCT format permitted the mapping of lithologic facies in the Pedra Branca Granite, using geobotanical associations, which occur in the form of variations in the density of cerrado vegetation, as well as the predominance of certain distinctive vegetation species. Dry season images did not show very good results in lithological differentiation due to anomalous illumination conditions related to the low solar elevation and the homogeneity in the vegetation cover, specially the grasses that become dry during this season. Rainy season image, on the other hand, allowed the separation of the lithological types, a fact that can be attributed to a greater differentiation among the geobotanical associations. As a result of this study, the muscovite-granite facies with greisenization zones, which are lithological indicators of important tin mineralization within the Serra da Pedra Branca Granite, were mapped. This methodology can be sucessfully applied to similar known granite bodies elsewhere in the Tin Province of Goias.

Distinguishing between tectonic and lithologic controls on bedrock channel longitudinal profiles using cosmogenic 10Be erosion rates and channel steepness index

USGS Publications Warehouse

Cyr, Andrew J.; Granger, Darryl E.; Olivetti, Valerio; Molin, Paola

2014-01-01

Knickpoints in fluvial channel longitudinal profiles and channel steepness index values derived from digital elevation data can be used to detect tectonic structures and infer spatial patterns of uplift. However, changes in lithologic resistance to channel incision can also influence the morphology of longitudinal profiles. We compare the spatial patterns of both channel steepness index and cosmogenic 10Be-determined erosion rates from four landscapes in Italy, where the geology and tectonics are well constrained, to four theoretical predictions of channel morphologies, which can be interpreted as the result of primarily tectonic or lithologic controls. These data indicate that longitudinal profile forms controlled by unsteady or nonuniform tectonics can be distinguished from those controlled by nonuniform lithologic resistance. In each landscape the distribution of channel steepness index and erosion rates is consistent with model predictions and demonstrates that cosmogenic nuclide methods can be applied to distinguish between these two controlling factors.

Frictional melting experiments investigate coseismic behaviour of pseudotachylyte-bearing faults in the Outer Hebrides Fault Zone, UK.

NASA Astrophysics Data System (ADS)

Campbell, L.; De Paola, N.; Nielsen, S. B.; Holdsworth, R.; Lloyd, G. E. E.; Phillips, R. J.; Walcott, R.

2015-12-01

Recent experimental studies, performed at seismic slip rates (≥ 1 m/s), suggest that the friction coefficient of seismic faults is significantly lower than at sub-seismic (< 1 mm/s) speeds. Microstructural observations, integrated with theoretical studies, suggest that the weakening of seismic faults could be due to a range of thermally-activated mechanisms (e.g. gel, nanopowder and melt lubrication, thermal pressurization, viscous flow), triggered by frictional heating in the slip zone. The presence of pseudotachylyte within both exhumed fault zones and experimental slip zones in crystalline rocks suggests that lubrication plays a key role in controlling dynamic weakening during rupture propagation. The Outer Hebrides Fault Zone (OHFZ), UK contains abundant pseudotachylyte along faults cutting varying gneissic lithologies. Our field observations suggest that the mineralogy of the protolith determines volume, composition and viscosity of the frictional melt, which then affects the coseismic weakening behaviour of the fault and has important implications for the magnitudes and distribution of stress drops during slip episodes. High velocity friction experiments at 18 MPa axial load, 1.3 ms-1 and up to 10 m slip were run on quartzo-feldspathic, metabasic and mylonitic samples, taken from the OHFZ in an attempt to replicate its coseismic frictional behaviour. These were configured in cores of a single lithology, or in mixed cores with two rock types juxtaposed. All lithologies produce a general trend of frictional evolution, where an initial peak followed by transient weakening precedes a second peak which then decays to a steady state. Metabasic and felsic single-lithology samples both produce sharper frictional peaks, at values of μ = 0.19 and μ= 0.37 respectively, than the broader and smaller (μ= 0.15) peak produced by a mixed basic-felsic sample. In addition, both single-lithology peaks occur within 0.2 m slip, whereas the combined-lithology sample displays a slower transition to the steady state, with the peak occurring after almost 2 m. Our results show that the frictional behaviour of faults in crystalline rocks, where different lithologies are in contact, is complex. Protolith composition determines the physical properties of the melt, which controls the evolution of coseismic friction.

Geochemical variability of the Yucatan basement: Constraints from crystalline clasts in Chicxulub impactites

NASA Astrophysics Data System (ADS)

Kettrup, B.; Deutsch, A.

2003-07-01

The 65 Ma old Chicxulub impact structure with a diameter of about 180 km is again in the focus of the geosciences because of the recently commenced drilling of the scientific well Yaxcopoil- 1. Chicxulub is buried beneath thick post-impact sediments, yet samples of basement lithologies in the drill cores provide a unique insight into age and composition of the crust beneath Yucatan. This study presents major element, Sr, and Nd isotope data for Chicxulub impact melt lithologies and clasts of basement lithologies in impact breccias from the PEMEX drill cores C-1 and Y-6, as well as data for ejecta material from the K/T boundaries at La Lajilla, Mexico, and Furlo, Italy. The impact melt lithologies have an andesitic composition with significantly varying contents of Al, Ca, and alkali elements. Their present day 87Sr/86Sr ratios cluster at about 0.7085, and 143Nd/144Nd ratios range from 0.5123 to 0.5125. Compared to the melt lithologies that stayed inside the crater, data for ejecta material show larger variations. The 87Sr/86Sr ratios range from 0.7081 for chloritized spherules from La Lajilla to 0.7151 for sanidine spherules from Furlo. The 143Nd/144Nd ratio is 0.5126 for La Lajilla and 0.5120 for the Furlo spherules. In an tCHUR(Nd)-tUR(Sr) diagram, the melt lithologies plot in a field delimited by Cretaceous platform sediments, various felsic lithic clasts and a newly found mafic fragment from a suevite. Granite, gneiss, and amphibolite have been identified among the fragments from crystalline basement gneiss. Their 87Sr/86Sr ratios range from 0.7084 to 0.7141, and their 143Nd/144Nd ratios range from 0.5121 to 0.5126. The TNdDM model ages vary from 0.7 to 1.4 Ga, pointing to different source terranes for these rocks. This leads us to believe that the geological evolution and the lithological composition of the Yucatàn basement is probably more complex than generally assumed, and Gondwanan as well as Laurentian crust may be present in the Yucatàn basement.

Systematic Lithologic Calibration of Neogene Mass-Transport Deposits Seismic Character in Mississippi Canyon of the Northern Gulf of Mexico, USA.

NASA Astrophysics Data System (ADS)

Gutierrez, M. A.; Snedden, J.

2017-12-01

Few publications have attempted detailed lithologic calibration of Mass Transport Deposits, usually as a byproduct of mud log descriptions. While the principal motivation for further understanding these slope failure deposits are driven by the economics of deep-water hydrocarbon exploration, the geohazard-related risks of storm-wave loading, and the shallow gas, also provide a driving concern for these deposits. Such risks can be mitigated and prevented by in depth analysis of slope stability and failure. The Mississippi Canyon of the Northern Gulf of Mexico is one of the few basins to contain enough available density of seismic and well data to provide a well-constrained lithologic characterization throughout a MTD-rich continental margin. The proposed hypothesis evaluates: 1) the differences between attached and detached MTDs in the Neogene Northern Gulf of Mexico through seismic characterization and well log analysis, 2) variations of MTD dimensions and map geometries in relation to depositional age throughout the northeastern and northcentral Gulf of Mexico, and 3) the differentiation between sand-prone and shale-prone MTD's in relation to associated depositional mechanisms. This study will attempt lithologic calibration of MTDs in Pleistocene -Miocene strata of the study area through integration of seismic observations (focused in supra-salt basins, which have the highest seismic data quality) and lithologic related information extracted from logs, mud logs (cuttings), and available core data to further constrain the distribution of MTD types, lithology, and geometries. Initial interpretations reflect a variance of seismic character responses to the presence of sandstone and shale (constrained by wells) throughout different regions and salt tectonic domains of the MTD geobodies. Further analysis will relate different seismic facies throughout MTDs to improve the understanding of seismic character and related lithologic facies throughout the deposits, in addition to also constraining the potential reservoir quality and seal integrity uncertainties of selected MTDs. Additionally, this approach can stand as an analog to other similar areas with much less well control, such as the southern Gulf of Mexico.

Geophysically inferred structural and lithologic map of the precambrian basement in the Joplin 1 degree by 2 degrees Quadrangle, Kansas and Missouri

USGS Publications Warehouse

McCafferty, Anne E.; Cordell, Lindrith E.

1992-01-01

This report is an analysis of regional gravity and aeromagnetic data that was carried out as part of a Conterminuous United States Mineral Assessment Program (CUSMAP) study of the Joplin 1° X 2° quadrangle, Kansas and Missouri. It is one in a series of reports representing a cooperative effort between the U.S. Geological Survey, Kansas Geological Survey, and Missouri Department of Natural Resources, Division of Geology and Land Survey. The work presented here is part of a larger project whose goal is to assess the mineral resource potential of the Paleozoic sedimentary section and crystalline basement within the quadrangle. Reports discussing geochemical, geological, and various other aspects of the study area are included in this Miscellaneous Field Studies Map series as MF-2125-A through MF-2125-E. Geophysical interpretation of Precambrian crystalline basement lithology and structure is the focus of this report. The study of the crystalline basement is complicated by the lack of exposures due to the presence of a thick sequence of Phanerozoic sedimentary cover. In areas where there are no outcrops, the geologist must turn to other indirect methods to assist in an understanding of the basement. Previous investigations of the buried basement in this region used available drill hole data, isotope age information, and regional geophysical data (Sims, 1990; Denison and others, 1984; Bickford and others, 1986). These studies were regional in scope and were presented at state and multistate scales. The work documented here used recently collected detailed gravity and aeromagnetic data to enhance the regional geologic knowledge of the area. Terrace-density and terrace-magnetization maps were calculated from the gravity and aeromagnetic data, leading directly to inferred physical-property (density and magnetization) maps. Once these maps were produced, the known geology and drill-hole data were reconciled with the physical-property maps to form a refined structural and lithologic map of the crystalline basement.

A High Resolution Microprobe Study of EETA79001 Lithology C

NASA Technical Reports Server (NTRS)

Schrader, Christian M.; Cohen, B. A.; Donovan, J. J.; Vicenzi, E. P.

2010-01-01

Antarctic meteorite EETA79001 has received substantial attention for possibly containing a component of Martian soil in its impact glass (Lithology C) [1]. The composition of Martian soil can illuminate near-surface processes such as impact gardening [2] and hydrothermal and volcanic activity [3,4]. Impact melts in meteorites represent our most direct samples of Martian regolith. We present the initial findings from a high-resolution electron microprobe study of Lithology C from Martian meteorite EETA79001. As this study develops we aim to extract details of a potential soil composition and to examine Martian surface processes using elemental ratios and correlations.

Rb-Sr and Sm-Nd Ages of Zagami DML and SR Isotopic Heterogeneity in Zagami

NASA Technical Reports Server (NTRS)

Nyquist, L.aurenceE.; Shih, C.-Y.; Reese, Y. D.

2010-01-01

Zagami contains lithologic heterogeneity suggesting that it did not form in a homogeneous, thick lava flow [1]. We have previously investigated the Sr and Nd isotopic systematics of Coarse-Grained (CG) and Fine-Grained (FG) lithologies described by [2]. Both appear to belong to Normal Zagami (NZ) [1,3], but their initial Sr-isotopic compositions differ [4,5]. Here we report new analyses of the Dark Mottled Lithology (DML, [3]) that show its age and initial Sr and Nd isotopic compositions to be identical within error limits with those of CG, but Sr initial isotopic compositions differ from those of FG.

Marquette Island: A Distinct Mafic Lithology Discovered by Opportunity

NASA Technical Reports Server (NTRS)

Mittlefehldt, David W.; Gellert, R.; Herkenhoff, K. E.; Clark, B. C.; Cohen, B. A.; Fleischer, I.; Jolliff, B. L.; Klingelhoefer, G.; Ming, D. W.; Yingst, R. A.

2010-01-01

While rolling over the Meridiani Planum sedimentary terrane, the rover Opportunity has occasionally discovered large, > 10 cm erratics. Most of these have proven to be meteorites [1], but one - Bounce Rock - is a martian basaltic rock similar in composition to the meteorite EETA79001 lithology B [2]. Presently, Opportunity is intensively investigating an --30 cm tall rock named Marquette Island that may be a distinct type of martian mafic lithology. We report the results of its continuing investigation using the Microscopic Imager (MI); Mossbauer Spectrometer (MB) and Alpha Particle X-ray Spectrometer (APXS). A companion abstract discusses the results of Panoramic Camera (Pancam) imaging of the rock [3].

Effect of lithological heterogeneity of bitumen sandstones on SAGD reservoir development

NASA Astrophysics Data System (ADS)

Korolev, E. A.; Usmanov, S. A.; Nikolaev, D. S.; Gabdelvaliyeva, R. R.

2018-05-01

The article describes the heavy oil field developed by the SAGD method. While development planning all the heterogeneity of the reservoir is must be taken into account. The objective of this work is to identify the distribution of lithological heterogeneities and their influence on oil production. For this reason, the studies of core samples were conducted and the heterogeneity was identified. Then properties and approximate geometry of lithological objects were studied. Also the effect of the heterogeneity on the heat propagation and production of fluid were analyzed. In the end, recommendations were made for the study of such heterogeneities on other deposits with similar geology

Geologic map and map database of the Palo Alto 30' x 60' quadrangle, California

USGS Publications Warehouse

Brabb, E.E.; Jones, D.L.; Graymer, R.W.

2000-01-01

This digital map database, compiled from previously published and unpublished data, and new mapping by the authors, represents the general distribution of bedrock and surficial deposits in the mapped area. Together with the accompanying text file (pamf.ps, pamf.pdf, pamf.txt), it provides current information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:62,500 or smaller.

Palaeoecology and sedimentology of the dysaerobic Bedford fauna (late Devonian), Ohio and Kentucky (USA)

USGS Publications Warehouse

Pashin, J.C.; Ettensohn, F.R.

1992-01-01

Oxygen-deficient biofacies models rely on lithologic and paleontologic attributes to identify distinctive biofacies interpreted to reflect levels of oxygenation in anaerobic, dysaerobic, and aerobic parts of a stratified water column. This study of the Bedford fauna from the Bedford Shale of Ohio and Kentucky and from adjacent black-shale units reports faunal distributions different from those predicted by the accepted models. This study suggests that, although oxygenation was an important factor that determined the taxonomic makeup of the fauna, bacterially mediated nutrient recycling and substrate characteristics were more important than oxygenation in determining faunal distribution in the dysaerobic zone. ?? 1992.

Geologic map and map database of western Sonoma, northernmost Marin, and southernmost Mendocino counties, California

USGS Publications Warehouse

Blake, M.C.; Graymer, R.W.; Stamski, R.E.

2002-01-01

This digital map database, compiled from previously published and unpublished data, and new mapping by the authors, represents the general distribution of bedrock and surficial deposits in the mapped area. Together with the accompanying text file (wsomf.ps, wsomf.pdf, wsomf.txt), it provides current information on the geologic structure and stratigraphy of the area covered. The database delineates map units that are identified by general age and lithology following the stratigraphic nomenclature of the U.S. Geological Survey. The scale of the source maps limits the spatial resolution (scale) of the database to 1:62,500 or smaller.

Simplified stratigraphic cross sections of the Eocene Green River Formation in the Piceance Basin, northwestern Colorado

USGS Publications Warehouse

Dietrich, John D.; Johnson, Ronald C.

2013-01-01

Thirteen stratigraphic cross sections of the Eocene Green River Formation in the Piceance Basin of northwestern Colorado are presented in this report. Originally published in a much larger and more detailed form by Self and others (2010), they are shown here in simplified, page-size versions that are easily accessed and used for presentation purposes. Modifications to the original versions include the elimination of the detailed lithologic columns and oil-yield histograms from Fischer assay data and the addition of ground-surface lines to give the depth of the various oil shale units shown on the cross section.

Determination of fluoride source in ground water using petrographic studies in Dashtestan area, south of Iran

NASA Astrophysics Data System (ADS)

Battaleb-Looie, Sedigheh; Moore, Farid, ,, Dr.

2010-05-01

The groundwater occurs in Dashtestan area, contains a high level of fluoride. Since groundwater is vastly used for drinking and irrigation purposes, the local residents are at high risk of fluoride toxicity, as already evidenced by the occurrence of dental Fluorosis in many residents. 35 surface and groundwater samples were collected in September, 2009. The results show that in 23 samples the fluoride concentration is above the permissible level (1.5ppm). Petrographic study of lithological units in the catchment area indicates that mica minerals are the most probable source of fluoride content in the study area.

Diapiric origin of the Blytheville and Pascola arches in the Reelfoot rift, east-central United States: Relation to New Madrid seismicity

DOE Office of Scientific and Technical Information (OSTI.GOV)

McKeown, F.A.; Diehl, S.F.; Glick, E.E.

1990-11-01

Most of the earthquakes in the New Madrid seismic zone correlate spatially with the Blytheville arch and part of the Pascoal arch, which are interpreted to be the same structure. Both arches may have formed by diapirism along the axis of the Reelfoot rift. Seismic, geophysical, and drill-hole data indicate that the rocks in the arches are highly deformed and fractured and have gross lithologic properties that make them weaker than rocks adjacent to the arches. The weaker rocks are inferred to fail seismically more readily than the stronger rocks adjacent to the arches.

Chronostratigraphic cross section of Cretaceous formations in western Montana, western Wyoming, eastern Utah, northeastern Arizona, and northwestern New Mexico, U.S.A.

USGS Publications Warehouse

Merewether, E. Allen; McKinney, Kevin C.

2015-01-01

In this transect for time-stratigraphic units of the Cretaceous, lateral changes in lithologies, regional differences in thicknesses, and the abundance of associated disconformities possibly reflect local and regional tectonic events. Examples of evidence of those events follow: (1) Disconformities and the absence of strata of lowest Cretaceous age in western Montana, western Wyoming, and northern Utah indicate significant tectonism and erosion probably during the Late Jurassic and earliest Cretaceous; ( 2) stages of Upper Cretaceous deposition in the transect display major lateral changes in thickness, which probably reflect regional and local tectonism.

Evaluation of repeated measurements of radon-222 concentrations in well water sampled from bedrock aquifers of the Piedmont near Richmond, Virginia, USA: effects of lithology and well characteristics.

PubMed

Harris, Shelley A; Billmeyer, Ernest R; Robinson, Michael A

2006-07-01

Radon (222Rn) concentrations in 26 ground water wells of two distinct lithologies in the Piedmont of Virginia were measured to assess variation in ground water radon concentrations (GWRC), to evaluate differences in concentrations related to well characteristics, lithology, and spatial distributions, and to assess the feasibility of predicting GWRC. Wells were sampled in accordance with American Public Health Association Method 7500 Rn-B, with modifications to include a well shaft profile analysis that determined the minimum purge time sufficient to remove the equivalent of one column of water from each well. Statistically significant differences in GWRC were found in the Trssu (1482 +/- 1711 pCi/L) and Mpg (7750 +/- 5188 pCi/L) lithologies, however, no significant differences were found among GWRC at each well over time. Using multiple regression, 86% of the variability (R2) in the GWRC was explained by the lithology, latitudinal class, and water table elevation of the wells. The GWRC in a majority of the wells studied exceed US Environmental Protection Agency designated maximum contaminant level and AMCL. Results support modifications to sampling procedures and indicate that, in previous studies, variations in GWRC concentrations over time may have been due in part to differences in sampling procedures and not in source water.

Evaluation of repeated measurements of radon-222 concentrations in well water sampled from bedrock aquifers of the Piedmont near Richmond, Virginia, USA: Effects of lithology and well characteristics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, Shelley A.; Billmeyer, Ernest R.; Robinson, Michael A.

Radon ({sup 222}Rn) concentrations in 26 ground water wells of two distinct lithologies in the Piedmont of Virginia were measured to assess variation in ground water radon concentrations (GWRC), to evaluate differences in concentrations related to well characteristics, lithology, and spatial distributions, and to assess the feasibility of predicting GWRC. Wells were sampled in accordance with American Public Health Association Method 7500 Rn-B, with modifications to include a well shaft profile analysis that determined the minimum purge time sufficient to remove the equivalent of one column of water from each well. Statistically significant differences in GWRC were found in themore » Trssu (1482{+-}1711 pCi/L) and Mpg (7750{+-}5188 pCi/L) lithologies, however, no significant differences were found among GWRC at each well over time. Using multiple regression, 86% of the variability (R {sup 2}) in the GWRC was explained by the lithology, latitudinal class, and water table elevation of the wells. The GWRC in a majority of the wells studied exceed US Environmental Protection Agency designated maximum contaminant level and AMCL. Results support modifications to sampling procedures and indicate that, in previous studies, variations in GWRC concentrations over time may have been due in part to differences in sampling procedures and not in source water.« less

Along-strike thickness variations of décollement levels controlling lateral changes in fold-and-thrust belts: the Barbastro-Balaguer Anticline (Southern Pyrenees)

NASA Astrophysics Data System (ADS)

Santolaria, Pablo; Calvín, Pablo; Pueyo, Emilio L.; Soto, Ruth; Ayala, Concepción; Casas, Antonio; Oliván, Carlota; Luzón, Aránzazu

2017-04-01

The subsurface vertical and lateral distribution of two evaporitic levels (Middle-Upper Triassic and Eocene) is here studied to better understand their role as a controlling factor on the geometry and kinematics of the central part of the South Pyrenean deformation front. Field work with hundreds of bedding attitudes, 5 exploration boreholes (up to 5000 m deep), the residual Bouguer anomaly and the interpretation of 27 seismic reflection profiles (approximately 440 km of sections) crossing the different allochthonous units and the adjacent Ebro foreland basin have been analysed in this work. Subsoil information is crucial because part of the studied area is extensively covered by the Oligocene-Miocene molasse that prevents any direct observation of the structure underneath to be done. Interpreted key horizons and faults have been identified from the lithological description of partially reinterpreted lithological well data and surface geology. Lithological well data has been anchored to seismic profiles by means of sonic log data. Kingdom software has been used to perform the 2D interpretation of seismic reflection profiles, supported by 2.5D gravity modelling, in a georeferenced workspace and then, surfaces of key horizons and faults were built and assembled together in a 3D model. The studied area is characterized from north to south by several minor thrust sheets, detached on the Middle-Upper Triassic décollement, which represents the basal décollement of the Pyrenees. Some of them can be linked with the South Pyrenean Frontal Thrust (SPFT) and others have structural continuation towards the NW. The SPFT displays a N160E trend and its hanging wall progressively deepens towards the west. To the east, this structure locally crops out. On the other hand, the footwall geometry of the SPBT shows very distinct features; the western part (External Sierras sector) displays a single ramp with moderate-high angle (20-30°) while the eastern part (linking zone to the Marginal Ranges) depicts mainly a ramp-flat geometry. Southwards, on the autochthonous deformation zone, the Barbastro-Balaguer Anticline (BBA) structure, which core is constituted by Eocene evaporites, seems to mimic the geometry of the SPFT. It displays a lateral change, from east to west, in both its orientation (N110E to N160E) and geometry (anticline to backthrust structure) probably linked to an important lateral thickness variation (as deduce from the residual anomaly map) of the Eocene evaporites that display a significant accumulation in the east and thin drastically and even disappear to the west. There, its distal pinch out is interpreted to promote the nucleation of the BBA backthrust. The distribution of the Eocene evaporites in the subsurface and the lateral changes in thickness are suggested to be significant factors during the late stages of the emplacement of the SPFT and associated structures.

Spatial association between dissection density and environmental factors over the entire conterminous United States

NASA Astrophysics Data System (ADS)

Luo, Wei; Jasiewicz, Jaroslaw; Stepinski, Tomasz; Wang, Jinfeng; Xu, Chengdong; Cang, Xuezhi

2016-01-01

Previous studies of land dissection density (D) often find contradictory results regarding factors controlling its spatial variation. We hypothesize that the dominant controlling factors (and the interactions between them) vary from region to region due to differences in each region's local characteristics and geologic history. We test this hypothesis by applying a geographical detector method to eight physiographic divisions of the conterminous United States and identify the dominant factor(s) in each. The geographical detector method computes the power of determinant (q) that quantitatively measures the affinity between the factor considered and D. Results show that the factor (or factor combination) with the largest q value is different for physiographic regions with different characteristics and geologic histories. For example, lithology dominates in mountainous regions, curvature dominates in plains, and glaciation dominates in previously glaciated areas. The geographical detector method offers an objective framework for revealing factors controlling Earth surface processes.

Chemical composition, stratigraphy, and depositional environments of the Black River Group (Middle Ordovician), southwestern Ohio.

USGS Publications Warehouse

Stith, David A.

1981-01-01

The chemical composition and stratigraphy of the Black River Group in southwestern Ohio were studied. Chemical analyses were done on two cores of the Black River from Adams and Brown Counties, Ohio. These studies show that substantial reserves of high-carbonate rock are present in the Black River at depths of less than 800 ft, in proximity to Cincinnati and the Ohio River. Stratigraphic studies show that the Black River Group has eight marker beds in its middle and upper portions and three distinct lithologic units in its lower portion; these marker beds and units are present throughout southwestern Ohio. The Black River Group correlates well with the High Bridge Group of Kentucky. Depositional environments of the Black River are similar to those of the High Bridge and to present-day tidal flats in the Bahamas.-Author

Sediment provenance in the Laxmi Basin of the Arabian Sea during the last 800 kyrs

NASA Astrophysics Data System (ADS)

Khim, B. K.; Horikawa, K.; Asahara, Y.; Kim, J. E.; Ikehara, M.; Lee, J.

2017-12-01

International Ocean Discovery Program Expedition 355 conducted to drill 1109.4 m penetration at Site U1456 in the Laxmi Basin of the Arabian Sea. Four lithologic units are defined onboard at Site U1456 (Pandey et al., 2016). Unit I is 121 m long, consisting mostly of pelagic carbonates (nannofossil ooze and/or foraminifera-rich nannofossil ooze) interbedded with thin terrigenous (clay, silt, and sand) turbidite layers. The age model of Unit I was determined by the correlation of δ18O fluctuations of planktonic foraminifera (Globigerinoides ruber) to LR04 stacks, estimating 1.2 Ma. A total of 60 samples, collected in the context of magnetic susceptibility (MS) changes at a discrete interval from a composite section (Holes U1456A and U1456C) of Unit I, were analyzed to measure Nd and Sr isotopes of detrital fraction. Based on Nd and Sr isotopes, the sediment provenance in the Laxmi Basin during the last 800 kyrs was traced in response to the monsoon activity between the interglacial and glacial periods. ɛNd and 87Sr/86Sr vary in a range from -12.4 to -8.0 and from 0.712 to 0.727, respectively. The correlation between ɛNd and 87Sr/86Sr is quite linear, indicating that the sediments were provided mainly by two dominant sources. Considering the ɛNd and 87Sr/86Sr end-members of sediment sources (i.e., river sediments), the Tapi River and Narmada River are the main contributors of sediments to Site U1456 with a little influence by the modern Indus River. However, the glacial sediments from the Indus River and the Mahi River may supply an additional fraction, leading to less ɛNd and more 87Sr/86Sr at Site U1456. Judged by the sediment sources, the sediments in the Laxmi Basin are characterized by the mixture of different provenances. In addition, it should be noted that the low ɛNd and high 87Sr/86Sr values coincide largely with high MS and vice versa, irrespectively of the glacial-interglacial change. Thus, rather than the sediment provenances, ɛNd and 87Sr/86Sr values of the detrital fraction in the Laxmi Basin of the Arabian Sea have been more controlled by the sedimentary processes (pelagic, hemi-pelagic and turbidite) and depositional conditions related with the sea level changes in response to the Arabian Sea monsoon activity between the glacial and interglacial periods during the last 800 kyrs.

Development of a Coupled Framework for Simulating Interactive Effects of Frozen Soil Hydrological Dynamics in Permafrost Regions

DTIC Science & Technology

2013-11-01

Permafrost Input Database Geology, Lithologic Data, Snow Cover, Air Temperature, Ground Temperatures, Vegetation Precipitation Soil Properties GIPL...be found in Nicolsky et al. (2007). Required input data include climate data, snow cover, soil thermal properties, lithological data, and vegetative

INFLUENCE OF SEDIMENT SUPPLY, LITHOLOGY, AND WOOD DEBRIS ON THE DISTRIBUTION OF BEDROCK AND ALLUVIAL CHANNELS

EPA Science Inventory

Field surveys in the Willapa River basin, Washington State, indicate that the drainage area?channel slope threshold describing the distribution of bedrock and alluvial channels is influenced by the underlying lithology and that local variations in sediment supply can overwhelm ba...

An application of the geophysical methods and ALS DTM for the identification of the geological structure in the Kraśnik region - Lublin Upland, Poland

NASA Astrophysics Data System (ADS)

Kamiński, Mirosław

2017-11-01

The purpose of the study was the assessment of the viability of selected geophysical methods and the Airborne Laser Scanning (ALS) for the identification and interpretation of the geological structure. The studied area is covered with a dense forest. For this reason, the ALS numerical terrain model was applied for the analysis of the topography. Three geophysical methods were used: gravimetric, in the form of a semi-detailed gravimetric photograph, Vertical Electrical Sounding (VES), and Electrical Resistivity Tomography (ERT). The numerical terrain model enabled the identification of Jurassic limestone outcrops and interpretation of the directions of the faults network. The geological interpretation of the digitally processed gravimetric data enabled the determination of the spatial orientation of the synclines and anticlines axes and of the course directions of main faults. Vertical Electrical Sounding carried along the section line perpendicular to the Gościeradów anticline axis enabled the interpretation of the lithology of this structure and identification of its complex tectonic structure. The shallow geophysical surveys using the ERT method enabled the estimation of the thickness of Quaternary formations deposited unconformably on the highly eroded Jurassic limestone outcrop. The lithology of Quaternary, Cretaceous and Jurassic rocks was also interpreted.

Investigating the scale of structural controls on chlorinated hydrocarbon distributions in the fractured-porous unsaturated zone of a sandstone aquifer in the UK

NASA Astrophysics Data System (ADS)

Lawrence, Adrian; Stuart, Marianne; Cheney, Colin; Jones, Neil; Moss, Richard

2006-12-01

Contaminant migration behaviour in the unsaturated zone of a fractured porous aquifer is discussed in the context of a study site in Cheshire, UK. The site is situated on gently dipping sandstones, adjacent to a linear lagoon historically used to dispose of industrial wastes containing chlorinated solvents. Two cores of more than 100 m length were recovered and measurements of chlorinated hydrocarbons (CHCs), inorganic chemistry, lithology, fracturing and aquifer properties were made. The results show that selecting an appropriate vertical sampling density is crucial both to providing an understanding of contaminant pathways and distinguishing whether CHCs are present in the aqueous or non-aqueous phase. The spacing of such sampling should be on a similar scale to the heterogeneity that controls water and contaminant movement. For some sections of the Permo-Triassic aquifer, significant changes in lithology and permeability occur over vertical distances of less than 1 m and samples need to be collected at this interval, otherwise considerable resolution is lost, potentially leading to erroneous interpretation of data. At this site, although CHC concentrations were high, the consistent ratio of the two main components of the plume (tetrachloroethene and trichloroethene) provided evidence of movement in the aqueous phase rather than in dense non-aqueous phase liquid (DNAPL).

Investigation of the foundations of a Byzantine church by three-dimensional seismic tomography

NASA Astrophysics Data System (ADS)

Polymenakos, L.; Papamarinopoulos, S.; Miltiadou, A.; Charkiolakis, N.

2005-02-01

Byzantine public buildings are of high historical and cultural value. Churches, in particular, are of high architectural and artistic value because they are built using various materials and construction techniques and may contain significant frescoes and mosaics. The knowledge of the state of foundations and ground material conditions is important for their proper restoration and preservation. Seismic tomography is employed to investigate the foundation structure and ground material of a Byzantine church. Energy sources are placed across the floor of the church and surrounding courts, while recorders are placed in a subterranean crypt. Travel time data are analyzed and processed with a three-dimensional (3D) tomographic inversion software in order to construct seismic velocity images at the foundation and below foundation level. Velocity variations are known to correlate well with the lithological character of the earth materials, thus providing important structural and lithological information. A case study from a Byzantine church of 11th c. A.D. in the suburbs of Athens, Greece, is presented. The objective of this research is the nondestructive investigation of unknown underground structures or void spaces, mainly under the floor of the building. The results are interpreted in terms of the foundation elements as well as of significant variations in the earth material character.

Controls on drainage divide migration in the northern Sierras Pampeanas assessed through morphometric indicators

NASA Astrophysics Data System (ADS)

Seagren, E. G.; Schoenbohm, L. M.

2017-12-01

Drainage reorganization, primarily through progressive divide migration leading to discrete stream captures, is increasingly recognized as a common phenomenon during mountain-building events. This drainage rearrangement reflects complex interactions between tectonics, climate, and lithology, and can fundamentally change erosion and sedimentation patterns; therefore, determining the spatial extent and potential controls of divide migration is vital to understanding the topographic evolution of orogenic landscapes. Both geomorphic and morphometric evidence can be used to identify such drainage reorganization. The northern Sierras Pampeanas is an ideal location in which to study divide migration as limited glaciation and low out-of-channel erosion rates preserve evidence of reorganization. Additionally, several ranges in the region, such as Sierra de las Planchadas, exhibit geomorphic evidence of drainage rearrangement, including wind gaps and hairpin turns. Using ArcGIS, LSDTopoTools, and TopoToolbox, we conducted a systematic analysis of the spatial distribution of three morphometric indicators of divide migration: χ, Mx, and local headwater relief. Local `hotspots' undergoing drainage divide migration were identified using spatial autocorrelation and clustering methods - Gi* and Moran's I. Using spatial regression analysis, we assessed the potential controls of lithology, modern TRMM precipitation rates, and tectonics over divide migration. Preliminary results suggest broad westward migration of main drainage divides, following both the orographic precipitation gradient and regional slope.