Assessment of Aerodynamic Challenges of a Variable-Speed Power Turbine for Large Civil Tilt-Rotor Application

NASA Technical Reports Server (NTRS)

Welch, Gerand E.

2010-01-01

The main rotors of the NASA Large Civil Tilt-Rotor notional vehicle operate over a wide speed-range (100% at take-off to 54% at cruise). The variable-speed power turbine, when coupled to a fixed-gear-ratio transmission, offers one approach to accomplish this speed variation. The key aero-challenges of the variable-speed power turbine are related to high work factors at cruise, where the power turbine operates at 54% of take-off speed, wide incidence variations into the vane, blade, and exit-guide-vane rows associated with the power-turbine speed change, and the impact of low aft-stage Reynolds number (transitional flow) at 28 kft cruise. Meanline and 2-D Reynolds-Averaged Navier- Stokes analyses are used to characterize the variable-speed power-turbine aerodynamic challenges and to outline a conceptual design approach that accounts for multi-point operation. Identified technical challenges associated with the aerodynamics of high work factor, incidence-tolerant blading, and low Reynolds numbers pose research needs outlined in the paper

Primary Hepatic Malignant Fibrous Histiocytoma on PET/CT.

PubMed

Liu, Yachao; Xu, Baixuan

2018-06-01

Malignant fibrous histiocytoma is mainly presented in extremities, less commonly in posterior peritoneum, but primary presented in liver is very rare and often with a poor prognosis because of its high aggression. The features of clinical presentations and images are variable and the pre-operative diagnosis is difficult. Here, we report a primary hepatic malignant fibrous histiocytoma patient with no distant metastasis showed on pre-operative F-FDG PET/CT, however with many metastases showed on the post-operative F-FDG PET/CT.

Software control program for 25 kW breadboard testing. [spacecraft power supplies; high voltage batteries

NASA Technical Reports Server (NTRS)

Pajak, J. A.

1981-01-01

A data acquisition software program developed to operate in conjunction with the automated control system of the 25 kW PM Electric Power System Breadboard Test facility is described. The proram provides limited interactive control of the breadboard test while acquiring data and monitoring parameters, allowing unattended continuous operation. The breadboard test facility has two positions for operating separate configurations. The main variable in each test setup is the high voltage Ni-Cd battery.

New approach for reduction of diesel consumption by comparing different mining haulage configurations.

PubMed

Rodovalho, Edmo da Cunha; Lima, Hernani Mota; de Tomi, Giorgio

2016-05-01

The mining operations of loading and haulage have an energy source that is highly dependent on fossil fuels. In mining companies that select trucks for haulage, this input is the main component of mining costs. How can the impact of the operational aspects on the diesel consumption of haulage operations in surface mines be assessed? There are many studies relating the consumption of fuel trucks to several variables, but a methodology that prioritizes higher-impact variables under each specific condition is not available. Generic models may not apply to all operational settings presented in the mining industry. This study aims to create a method of analysis, identification, and prioritization of variables related to fuel consumption of haul trucks in open pit mines. For this purpose, statistical analysis techniques and mathematical modelling tools using multiple linear regressions will be applied. The model is shown to be suitable because the results generate a good description of the fuel consumption behaviour. In the practical application of the method, the reduction of diesel consumption reached 10%. The implementation requires no large-scale investments or very long deadlines and can be applied to mining haulage operations in other settings. Copyright © 2016 Elsevier Ltd. All rights reserved.

Towards Improved Forecasts of Atmospheric and Oceanic Circulations over the Complex Terrain of the Eastern Mediterranean

NASA Technical Reports Server (NTRS)

Chronis, Themis; Case, Jonathan L.; Papadopoulos, Anastasios; Anagnostou, Emmanouil N.; Mecikalski, John R.; Haines, Stephanie L.

2008-01-01

Forecasting atmospheric and oceanic circulations accurately over the Eastern Mediterranean has proved to be an exceptional challenge. The existence of fine-scale topographic variability (land/sea coverage) and seasonal dynamics variations can create strong spatial gradients in temperature, wind and other state variables, which numerical models may have difficulty capturing. The Hellenic Center for Marine Research (HCMR) is one of the main operational centers for wave forecasting in the eastern Mediterranean. Currently, HCMR's operational numerical weather/ocean prediction model is based on the coupled Eta/Princeton Ocean Model (POM). Since 1999, HCMR has also operated the POSEIDON floating buoys as a means of state-of-the-art, real-time observations of several oceanic and surface atmospheric variables. This study attempts a first assessment at improving both atmospheric and oceanic prediction by initializing a regional Numerical Weather Prediction (NWP) model with high-resolution sea surface temperatures (SST) from remotely sensed platforms in order to capture the small-scale characteristics.

Engineering approach for cost effective operation of industrial pump systems

NASA Astrophysics Data System (ADS)

Krickis, O.; Oleksijs, R.

2017-10-01

Power plants operators are persuaded to operate the main equipment such as centrifugal pumps in economically effective way. The operation of pump sets of district heating network at power plants should be done according to prescriptions of the original equipment manufacturer with further implementation of these requirements to distributed control system of the plant. In order to operate industrial pump sets with a small number of malfunctions is necessary to control the duty point of pump sets in H-Q coordinates, which could be complex task in some installations. Alternatively, pump operation control could be organized in H-n (head vs rpm) coordinates, utilizing pressure transmitters in pressure pipeline and value of rpm from variable speed driver. Safe operation range of the pump has to be limited with system parabolas, which prevents the duty point location outside of the predefined operation area. The particular study demonstrates the engineering approach for pump’s safe operation control development in MATLAB/Simulink environment, which allows to simulate the operation of the pump at different capacities in hydraulic system with variable characteristic and to predefine the conditions for efficient simultaneous pump operation in parallel connection.

Adaptive EAGLE dynamic solution adaptation and grid quality enhancement

NASA Technical Reports Server (NTRS)

Luong, Phu Vinh; Thompson, J. F.; Gatlin, B.; Mastin, C. W.; Kim, H. J.

1992-01-01

In the effort described here, the elliptic grid generation procedure in the EAGLE grid code was separated from the main code into a subroutine, and a new subroutine which evaluates several grid quality measures at each grid point was added. The elliptic grid routine can now be called, either by a computational fluid dynamics (CFD) code to generate a new adaptive grid based on flow variables and quality measures through multiple adaptation, or by the EAGLE main code to generate a grid based on quality measure variables through static adaptation. Arrays of flow variables can be read into the EAGLE grid code for use in static adaptation as well. These major changes in the EAGLE adaptive grid system make it easier to convert any CFD code that operates on a block-structured grid (or single-block grid) into a multiple adaptive code.

A waste characterisation procedure for ADM1 implementation based on degradation kinetics.

PubMed

Girault, R; Bridoux, G; Nauleau, F; Poullain, C; Buffet, J; Steyer, J-P; Sadowski, A G; Béline, F

2012-09-01

In this study, a procedure accounting for degradation kinetics was developed to split the total COD of a substrate into each input state variable required for Anaerobic Digestion Model n°1. The procedure is based on the combination of batch experimental degradation tests ("anaerobic respirometry") and numerical interpretation of the results obtained (optimisation of the ADM1 input state variable set). The effects of the main operating parameters, such as the substrate to inoculum ratio in batch experiments and the origin of the inoculum, were investigated. Combined with biochemical fractionation of the total COD of substrates, this method enabled determination of an ADM1-consistent input state variable set for each substrate with affordable identifiability. The substrate to inoculum ratio in the batch experiments and the origin of the inoculum influenced input state variables. However, based on results modelled for a CSTR fed with the substrate concerned, these effects were not significant. Indeed, if the optimal ranges of these operational parameters are respected, uncertainty in COD fractionation is mainly limited to temporal variability of the properties of the substrates. As the method is based on kinetics and is easy to implement for a wide range of substrates, it is a very promising way to numerically predict the effect of design parameters on the efficiency of an anaerobic CSTR. This method thus promotes the use of modelling for the design and optimisation of anaerobic processes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Formulation development and optimization of a novel Cremophore EL-based nanoemulsion using ultrasound cavitation.

PubMed

Tang, Siah Ying; Manickam, Sivakumar; Wei, Tan Khang; Nashiru, Billa

2012-03-01

In the present study, response surface methodology (RSM) based on central composite design (CCD) was employed to investigate the influence of main emulsion composition variables, namely drug loading, oil content, emulsifier content as well as the effect of the ultrasonic operating parameters such as pre-mixing time, ultrasonic amplitude, and irradiation time on the properties of aspirin-loaded nanoemulsions. The two main emulsion properties studied as response variables were: mean droplet size and polydispersity index. The ultimate goal of the present work was to determine the optimum level of the six independent variables in which an optimal aspirin nanoemulsion with desirable properties could be produced. The response surface analysis results clearly showed that the variability of two responses could be depicted as a linear function of the content of main emulsion compositions and ultrasonic processing variables. In the present investigation, it is evidently shown that ultrasound cavitation is a powerful yet promising approach in the controlled production of aspirin nanoemulsions with smaller average droplet size in a range of 200-300 nm and with a polydispersity index (PDI) of about 0.30. This study proved that the use of low frequency ultrasound is of considerable importance in the controlled production of pharmaceutical nanoemulsions in the drug delivery system. Copyright © 2011 Elsevier B.V. All rights reserved.

Orbital Express Mission Operations Planning and Resource Management using ASPEN

NASA Technical Reports Server (NTRS)

Chouinard, Caroline; Knight, Russell; Jones, Grailing; Tran, Daniel

2008-01-01

As satellite equipment and mission operations become more costly, the drive to keep working equipment running with less man-power rises.Demonstrating the feasibility of autonomous satellite servicing was the main goal behind the Orbital Express (OE) mission. Planning the satellite mission operations for OE required the ability to create a plan which could be executed autonomously over variable conditions. The Automated-Scheduling and Planning Environment (ASPEN)tool, developed at the Jet Propulsion Laboratory, was used to create the schedule of events in each daily plan for the two satellites of the OE mission. This paper presents an introduction to the ASPEN tool, the constraints of the OE domain, the variable conditions that were presented within the mission, and the solution to operations that ASPEN provided. ASPEN has been used in several other domains, including research rovers, Deep Space Network scheduling research, and in flight operations for the ASE project's EO1 satellite. Related work is discussed, as are the future of ASPEN and the future of autonomous satellite servicing.

Valorisation of waste tyre by pyrolysis in a moving bed reactor.

PubMed

Aylón, E; Fernández-Colino, A; Murillo, R; Navarro, M V; García, T; Mastral, A M

2010-07-01

The aim of this work is to assess the behaviour of a moving bed reactor, based on a screw transporter design, in waste tyre pyrolysis under several experimental conditions. Waste tyre represents a significant problem in developed countries and it is necessary to develop new technology that could easily process big amounts of this potentially raw material. In this work, the influence of the main pyrolysis process variables (temperature, solid residence time, mass flow rate and inert gas flow) has been studied by a thorough analysis of product yields and properties. It has been found that regardless the process operational parameters, a total waste tyre devolatilisation is achieved, producing a pyrolytic carbon black with a volatile matter content under 5 wt.%. In addition, it has been proven that, in the range studied, the most influencing process variables are temperature and solid mass flow rate, mainly because both variables modify the gas residence time inside the reactor. In addition, it has been found that the modification of these variables affects to the chemical properties of the products. This fact is mainly associated to the different cracking reaction of the primary pyrolysis products. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

Cardiac surgery productivity and throughput improvements.

PubMed

Lehtonen, Juha-Matti; Kujala, Jaakko; Kouri, Juhani; Hippeläinen, Mikko

2007-01-01

The high variability in cardiac surgery length--is one of the main challenges for staff managing productivity. This study aims to evaluate the impact of six interventions on open-heart surgery operating theatre productivity. A discrete operating theatre event simulation model with empirical operation time input data from 2603 patients is used to evaluate the effect that these process interventions have on the surgery output and overtime work. A linear regression model was used to get operation time forecasts for surgery scheduling while it also could be used to explain operation time. A forecasting model based on the linear regression of variables available before the surgery explains 46 per cent operating time variance. The main factors influencing operation length were type of operation, redoing the operation and the head surgeon. Reduction of changeover time between surgeries by inducing anaesthesia outside an operating theatre and by reducing slack time at the end of day after a second surgery have the strongest effects on surgery output and productivity. A more accurate operation time forecast did not have any effect on output, although improved operation time forecast did decrease overtime work. A reduction in the operation time itself is not studied in this article. However, the forecasting model can also be applied to discover which factors are most significant in explaining variation in the length of open-heart surgery. The challenge in scheduling two open-heart surgeries in one day can be partly resolved by increasing the length of the day, decreasing the time between two surgeries or by improving patient scheduling procedures so that two short surgeries can be paired. A linear regression model is created in the paper to increase the accuracy of operation time forecasting and to identify factors that have the most influence on operation time. A simulation model is used to analyse the impact of improved surgical length forecasting and five selected process interventions on productivity in cardiac surgery.

A Methodological Approach for Training Analysts of Small Business Problems.

ERIC Educational Resources Information Center

Mackness, J. R.

1986-01-01

Steps in a small business analysis are discussed: understand how company activities interact internally and with markets and suppliers; know the relative importance of controllable management variables; understand the social atmosphere within the company; analyze the operations of the company; define main problem areas; identify possible actions…

Variant adrenal venous anatomy in 546 laparoscopic adrenalectomies.

PubMed

Scholten, Anouk; Cisco, Robin M; Vriens, Menno R; Shen, Wen T; Duh, Quan-Yang

2013-04-01

Knowing the types and frequency of adrenal vein variants would help surgeons identify and control the adrenal vein during laparoscopic adrenalectomy. To establish the surgical anatomy of the main vein and its variants for laparoscopic adrenalectomy and to analyze the relationship between variant adrenal venous anatomy and tumor size, pathologic diagnosis, and operative outcomes. In a retrospective review of patients at a tertiary referral hospital, 506 patients underwent 546 consecutive laparoscopic adrenalectomies between April 22, 1993, and October 21, 2011. Patients with variant adrenal venous anatomy were compared with patients with normal adrenal venous anatomy regarding preoperative variables (patient and tumor characteristics [size and location] and clinical diagnosis), intraoperative variables (details on the main adrenal venous drainage, any variant venous anatomy, duration of operation, rate of conversion to hand-assisted or open procedure, and estimated blood loss), and postoperative variables (transfusion requirement, reoperation for bleeding, duration of hospital stay, and histologic diagnosis). Laparoscopic adrenalectomy. Prevalence of variant adrenal venous anatomy and its relationship to tumor characteristics, pathologic diagnosis, and operative outcomes. Variant venous anatomy was encountered in 70 of 546 adrenalectomies (13%). Variants included no main adrenal vein identifiable (n = 18), 1 main adrenal vein with additional small veins (n = 11), 2 adrenal veins (n = 20), more than 2 adrenal veins (n = 14), and variants of the adrenal vein drainage to the inferior vena cava and hepatic vein or of the inferior phrenic vein (n = 7). Variants occurred more often on the right side than on the left side (42 of 250 glands [17%] vs. 28 of 296 glands [9%], respectively; P = .02). Patients with variant anatomy compared with those with normal anatomy had larger tumors (mean, 5.1 vs 3.3 cm, respectively; P < .001), more pheochromocytomas (24 of 70 [35%] vs. 100 of 476 [21%], respectively; P = .02), and more estimated blood loss (mean, 134 vs. 67 mL, respectively; P = .01). For patients with variant anatomy vs those with normal anatomy, the rates of transfusion requirement (2 of 70 [3%] vs. 10 of 476 [2%], respectively; P = .69) and reoperation for bleeding (1 of 70 [1%] vs. 3 of 476 [1%]; P = .46) were similar between groups. Understanding variant adrenal venous anatomy is important to avoid bleeding during laparoscopic adrenalectomy, particularly in patients with large tumors or pheochromocytomas. Surgeons should anticipate a higher probability of adrenal vein variants when operating on pheochromocytomas and larger adrenal tumors.

Digital sun sensor multi-spot operation.

PubMed

Rufino, Giancarlo; Grassi, Michele

2012-11-28

The operation and test of a multi-spot digital sun sensor for precise sun-line determination is described. The image forming system consists of an opaque mask with multiple pinhole apertures producing multiple, simultaneous, spot-like images of the sun on the focal plane. The sun-line precision can be improved by averaging multiple simultaneous measures. Nevertheless, the sensor operation on a wide field of view requires acquiring and processing images in which the number of sun spots and the related intensity level are largely variable. To this end, a reliable and robust image acquisition procedure based on a variable shutter time has been considered as well as a calibration function exploiting also the knowledge of the sun-spot array size. Main focus of the present paper is the experimental validation of the wide field of view operation of the sensor by using a sensor prototype and a laboratory test facility. Results demonstrate that it is possible to keep high measurement precision also for large off-boresight angles.

Characterization of Volatiles Loss from Soil Samples at Lunar Environments

NASA Technical Reports Server (NTRS)

Kleinhenz, Julie; Smith, Jim; Roush, Ted; Colaprete, Anthony; Zacny, Kris; Paulsen, Gale; Wang, Alex; Paz, Aaron

2017-01-01

Resource Prospector Integrated Thermal Vacuum Test Program A series of ground based dirty thermal vacuum tests are being conducted to better understand the subsurface sampling operations for RP Volatiles loss during sampling operations Hardware performance Sample removal and transfer Concept of operationsInstrumentation5 test campaigns over 5 years have been conducted with RP hardware with advancing hardware designs and additional RP subsystems Volatiles sampling 4 years Using flight-forward regolith sampling hardware, empirically determine volatile retention at lunar-relevant conditions Use data to improve theoretical predictions Determine driving variables for retention Bound water loss potential to define measurement uncertainties. The main goal of this talk is to introduce you to our approach to characterizing volatiles loss for RP. Introduce the facility and its capabilities Overview of the RP hardware used in integrated testing (most recent iteration) Summarize the test variables used thus farReview a sample of the results.

Multiparametric evaluation of risk factors associated to seroma formation in abdominal wall surgery.

PubMed

Licari, L; Salamone, G; Parinisi, Z; Campanella, S; Sabatino, C; Ciolino, G; De Marco, P; Falco, N; Boventre, S; Gulotta, G

2017-01-01

Incisional hernia is one of the main topics in the general surgery since there is not a unanimous consensus concerning to the best surgical methodology to adopt. It seems that prosthetic surgery is the best technique, even if responsible for the development of periprosthetic seroma. The aim of this study is to assess whether the preoperative abnormalities of the bio-humoral parameters may be considered as risk factors for seroma. From July 2016 to July 2017 at the "Policlinico Paolo Giaccone", Palermo, Department of Emergency Surgery, 56 patients included in this study, underwent laparotomic mesh repair. The inclusion criteria were: age > 18 years, incisional hernia W2R0 according to the Chevrel classification and a monoperator technique. The main variables were: sex, age, BMI, smoke, ASA score, and co-morbidities. Among the main serum-blood variables: natraemia, kalaemia, chloraemia, calcaemia, PCR, level of glucose, creatinine, albumin and proteins in the blood. The data were analyzed using SPSS software. Univariate analysis highlighted hypo- and hyper-natraemia, hyper-kalaemia, hypo-chloraemia, high levels of PCR, hyper-glycemia, low level of serum-blood albumin and proteins, as statistically significant variables. Multivariate analysis revealed a p<0.05 for PCR, hypo-albuminemia and total serum-blood-protein level. Alterations of pre-operative bio-humoral parameters could be associated to a greater risk of seroma development. A better understanding of such alterations may lead to more efficient risk stratification methods. This could be essential to better address the medical resources, reducing the post-operative complications and the outpatient controls as well as the risk associated to seroma.

Operator induced variability in left ventricular measurements with cardiovascular magnetic resonance is improved after training.

PubMed

Karamitsos, Theodoros D; Hudsmith, Lucy E; Selvanayagam, Joseph B; Neubauer, Stefan; Francis, Jane M

2007-01-01

Accurate and reproducible measurement of left ventricular (LV) mass and function is a significant strength of Cardiovascular Magnetic Resonance (CMR). Reproducibility and accuracy of these measurements is usually reported between experienced operators. However, an increasing number of inexperienced operators are now training in CMR and are involved in post-processing analysis. The aim of the study was to assess the interobserver variability of the manual planimetry of LV contours amongst two experienced and six inexperienced operators before and after a two months training period. Ten healthy normal volunteers (5 men, mean age 34+/-14 years) comprised the study population. LV volumes, mass, and ejection fraction were manually evaluated using Argus software (Siemens Medical Solutions, Erlangen, Germany) for each subject, once by the two experienced and twice by the six inexperienced operators. The mean values of experienced operators were considered the reference values. The agreement between operators was evaluated by means of Bland-Altman analysis. Training involved standardized data acquisition, simulated off-line analysis and mentoring. The trainee operators demonstrated improvement in the measurement of all the parameters compared to the experienced operators. The mean ejection fraction variability improved from 7.2% before training to 3.7% after training (p=0.03). The parameter in which the trainees showed the least improvement was LV mass (from 7.7% to 6.7% after training). The basal slice selection and contour definition were the main sources of errors. An intensive two month training period significantly improved the accuracy of LV functional measurements. Adequate training of new CMR operators is of paramount importance in our aim to maintain the accuracy and high reproducibility of CMR in LV function analysis.

Hydrodynamics of a Multistage Wet Scrubber Incineration Conditions

ERIC Educational Resources Information Center

Said, M. M.; Manyele, S. V.; Raphael, M. L.

2012-01-01

The objective of the study was to determine the hydrodynamics of the two stage counter-current cascade wet scrubbers used during incineration of medical waste. The dependence of the hydrodynamics on two main variables was studied: Inlet air flow rate and inlet liquid flow rate. This study introduces a new wet scrubber operating features, which are…

Construction and Operation Costs of Wastewater Treatment and Implications for the Paper Industry in China.

PubMed

Niu, Kunyu; Wu, Jian; Yu, Fang; Guo, Jingli

2016-11-15

This paper aims to develop a construction and operation cost model of wastewater treatment for the paper industry in China and explores the main factors that determine these costs. Previous models mainly involved factors relating to the treatment scale and efficiency of treatment facilities for deriving the cost function. We considered the factors more comprehensively by adding a regional variable to represent the economic development level, a corporate ownership factor to represent the plant characteristics, a subsector variable to capture pollutant characteristics, and a detailed-classification technology variable. We applied a unique data set from a national pollution source census for the model simulation. The major findings include the following: (1) Wastewater treatment costs in the paper industry are determined by scale, technology, degree of treatment, ownership, and regional factors; (2) Wastewater treatment costs show a large decreasing scale effect; (3) The current level of pollutant discharge fees is far lower than the marginal treatment costs for meeting the wastewater discharge standard. Key implications are as follows: (1) Cost characteristics and impact factors should be fully recognized when planning or making policies relating to wastewater treatment projects or technology development; (2) There is potential to reduce treatment costs by centralizing wastewater treatment via industrial parks; (3) Wastewater discharge fee rates should be increased; (4) Energy efficient technology should become the future focus of wastewater treatment.

Nomenclature and guideline to express the amount of a membrane protein synthesized in animal cells in view of bioprocess optimization and production monitoring.

PubMed

Augusto, Elisabeth F P; Moraes, Angela M; Piccoli, Rosane A M; Barral, Manuel F; Suazo, Cláudio A T; Tonso, Aldo; Pereira, Carlos A

2010-01-01

Studies of a bioprocess optimization and monitoring for protein synthesis in animal cells face a challenge on how to express in quantitative terms the system performance. It is possible to have a panel of calculated variables that fits more or less appropriately the intended goal. Each mathematical expression approach translates different quantitative aspects. We can basically separate them into two categories: those used for the evaluation of cell physiology in terms of product synthesis, which can be for bioprocess improvement or optimization, and those used for production unit sizing and for bioprocess operation. With these perspectives and based on our own data of kinetic S2 cells growth and metabolism, as well as on their synthesis of the transmembrane recombinant rabies virus glycoprotein, here indicated as P, we show and discuss the main characteristics of calculated variables and their recommended use. Mainly applied to a bioprocess improvement/optimization and that mainly used for operation definition and to design the production unit, we expect these definitions/recommendations would improve the quality of data produced in this field and lead to more standardized procedures. In turn, it would allow a better and easier comprehension of scientific and technological communications for specialized readers. Copyright 2009 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

Selection of labyrinth seals in steam turbines

NASA Astrophysics Data System (ADS)

Kostyuk, A. G.

2015-01-01

The efficiency, vibration stability, operational durability, and cost of the main types of peripheral seals used in steam turbines are considered. A comparison between the conventional and honeycomb seals is given. Conditions subject to which replacement of conventional seals by honeycomb ones can be justified are pointed out. The use of variable-pitch multicomb seals as the most promising ones is recommended.

VizieR Online Data Catalog: LMC OGLE-III Shallow Survey variable stars (Ulaczyk+, 2013)

NASA Astrophysics Data System (ADS)

Ulaczyk, K.; Szymanski, M. K.; Udalski, A.; Kubiak, M.; Pietrzynski, G.; Soszynski, I.; Wyrzykowski, L.; Poleski, R.; Gieren, W.; Walker, A. R.; Garcia-Varela, A.

2017-07-01

Photometric data were collected using the 1.3-m Warsaw Telescope located at Las Campanas Observatory, operated by the Carnegie Institution for Science. We used exactly the same photometric system as in the OGLE-III main survey. Detailed information about whole instrumentation can be found in Udalski (2003AcA....53..291U). (5 data files).

Hydrometallurgical separation of rare earth elements, cobalt and nickel from spent nickel-metal-hydride batteries

NASA Astrophysics Data System (ADS)

Rodrigues, Luiz Eduardo Oliveira Carmo; Mansur, Marcelo Borges

The separation of rare earth elements, cobalt and nickel from NiMH battery residues is evaluated in this paper. Analysis of the internal content of the NiMH batteries shows that nickel is the main metal present in the residue (around 50% in weight), as well as potassium (2.2-10.9%), cobalt (5.1-5.5%), rare earth elements (15.3-29.0%) and cadmium (2.8%). The presence of cadmium reveals that some Ni-Cd batteries are possibly labeled as NiMH ones. The leaching of nickel and cobalt from the NiMH battery powder with sulfuric acid is efficient; operating variables temperature and concentration of H 2O 2 has no significant effect for the conditions studied. A mixture of rare earth elements is separated by precipitation with NaOH. Finally, solvent extraction with D2EHPA (di-2-ethylhexyl phosphoric acid) followed by Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) can separate cadmium, cobalt and nickel from the leach liquor. The effect of the main operating variables of both leaching and solvent extraction steps are discussed aiming to maximize metal separation for recycling purposes.

Predictors of Operative Mortality for Coronary Bypass Grafting in Patients with Ischemic Heart Disease

PubMed Central

Langou, Rene A.; Wiles, John C.; Peduzzi, Peter N.; Hammond, Graeme; Cohen, Lawrence S.

1978-01-01

Predictors for operative mortality (OM) were studied in 172 consecutive patients (pts) undergoing coronary artery grafts (CAG) for angina pectoris. Seventy eight pts had Class IV angina; of the 147 patients given propranolol, 41 were gradually withdrawn from propranolol and finally discontinued 24 hours before surgery, and 106 were abruptly withdrawn from propranolol 24 hours before CAG; 20 pts had left main coronary disease; 156 pts had cardiopulmonary bypass (CPB) time shorter than 20 minutes, and 16 pts had a CPB longer than 120 minutes. The operative mortality was 5.2% (9/172) for the entire group. Class IV angina (OM 7%), abrupt propranolol withdrawal (OM 6.6%), left main coronary artery disease (OM 25%), and CPB longer than 120 minutes (OM 50%), all significantly increased OM. These variables were interdependent, however, as many pts belonged to several predictor categories, combinations of predictors were examined, in order to more accurately predict the risk of individual pts. The combination of left main coronary artery disease and CPB longer than 120 minutes; and Class IV angina and CPB longer than 120 minutes were significantly associated with higher operative mortality. We conclude that Class IV angina, abrupt propranolol withdrawal, left main coronary artery disease and prolonged CPB are potent, interdependent predictors of OM in pts undergoing CAG. Consideration of these predictors, alone and in combination, allows effective prediction of OM for CAG in patients with stable angina pectoris. PMID:307873

Measurement of strains at high temperatures by means of a portable holographic moire camera

NASA Astrophysics Data System (ADS)

Sciammarella, C. A.; Bhat, G.; Shao, Y.

Electronic holographic moire is utilized to measure strains at temperatures up to 1000 C. A CW laser operating at 50 mW and at the wavelength of 632.8 nm is used to illuminate the objects under study. The main variables influencing the fringe patterns visibility are discussed and measurements are performed to obtain the values of these variables in the performed experiments. The coefficient of expansion of an alloy is measured at temperatures ranging from 797 C to 986 C. Excellent agreement is found between the measured values and those provided by the manufacturer.

Measurement of strains at high temperatures by means of a portable holographic moire camera

NASA Technical Reports Server (NTRS)

Sciammarella, C. A.; Bhat, G.; Shao, Y.

1989-01-01

Electronic holographic moire is utilized to measure strains at temperatures up to 1000 C. A CW laser operating at 50 mW and at the wavelength of 632.8 nm is used to illuminate the objects under study. The main variables influencing the fringe patterns visibility are discussed and measurements are performed to obtain the values of these variables in the performed experiments. The coefficient of expansion of an alloy is measured at temperatures ranging from 797 C to 986 C. Excellent agreement is found between the measured values and those provided by the manufacturer.

[Is the stomach a main landmark on the abdominal circumference? Audit of 3 operators].

PubMed

Laurent, A-C; Blanc, J; Grangé, G

2016-05-01

The fetal weight estimation depends largely on the accuracy of abdominal circumference. The quality criteria are standardized to minimize variability and include visualization of the stomach. The objective of this study is to investigate the presence or absence of the stomach on the abdominal circumference for 3 different operators. We conducted re-reading of 204 ultrasound images in the second and third trimester of pregnancy, performed by three operators, at the maternity Port Royal in Paris in 2013. On these images, the presence of the stomach was sought and other quality criteria were verified. Among the 204 images, 166 included the stomach (81%). When studying for each of the three operators, there were 79%, 72% and 98% of the stomach into the abdominal circumference, a significant difference between operators (P=0.0029). Regarding the secondary criteria, the quality criteria found most often were the calipers and well placed ellipse (89%). According to the previous studies, the stomach seems to be a reference to search. Our study shows variability depending on the different operators. If a hierarchy of quality criteria is to be considered, the stomach does not seem to be the first criterion to search. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Cost accounting in a surgical unit in a teaching hospital--a pilot study.

PubMed

Malalasekera, A P; Ariyaratne, M H; Fernando, R; Perera, D; Deen, K I

2003-09-01

Economic constraints remain one of the major limitations on the quality of health care even in industrialised countries. Improvement of quality will require optimising facilities within available resources. Our objective was to determine costs of surgery and to identify areas where cost reduction is possible. 80 patients undergoing routine major and intermediate surgery during a period of 6 months were selected at random. All consumables used and procedures carried out were documented. A unit cost was assigned to each of these. Costing was based on 3 main categories: preoperative (investigations, blood product related costs), operative (anaesthetic charges, consumables and theatre charges) and post-operative (investigations, consumables, hospital stay). Theatre charges included two components: fixed (consumables) and variable (dependent on time per operation). The indirect costs (e.g. administration costs, 'hotel' costs), accounted for 30%, of the total and were lower than similar costs in industrialised nations. The largest contributory factors (median, range) towards total cost were, basic hospital charges (30%; 15 to 63%); theatre charges fixed (23%; 6 to 35%) and variable (14%; 8 to 27%); and anaesthetic charges (15%; 1 to 36%). Cost reduction in patients undergoing surgery should focus on decreasing hospital stay, operating theatre time and anaesthetic expenditure. Although definite measures can be suggested from the study, further studies on these variables are necessary to optimise cost effectiveness of surgical units.

Development of a heavy duty portable variable power supply (HPVPS)

NASA Astrophysics Data System (ADS)

Musa, Ahmad Zulfadli Bin; Lung, Chong Man; Abidin, Wan'Amirah Basyarah Binti Zainol

2017-08-01

This paper covers the innovation of a Heavy Duty Portable Variable Power Supply (HPVPS) in Jabatan Kejuruteraan Elektrik (JKE), Politeknik Mukah, Sarawak (PMU). This project consists of variable power supply which can vary the output from 1.2 V to 11.6V, AC pure wave inverter to convert DC to AC for the operation of low power home appliances and also used Li-on rechargeable batteries to store the electrical energy and additional feature that can be used to jump-start the batteries of the car. The main objective of this project is to make the user can operate the electronic devices anywhere whenever if no electricity while doing their lab activities. Most of the regulated power supply in JKE lab aged 9-10 years old and need periodical maintenance and need cost and also the unit can be used is not enough to support the whole class during lab activities. As a result, the P&P process will be facing the major problem in order to make the lab activities running smoothly. By development of the portable variable power supply, the P&P process is more efficient and very helpful.

Stellar Variability at the Main-sequence Turnoff of the Intermediate-age LMC Cluster NGC 1846

NASA Astrophysics Data System (ADS)

Salinas, R.; Pajkos, M. A.; Vivas, A. K.; Strader, J.; Contreras Ramos, R.

2018-04-01

Intermediate-age (IA) star clusters in the Large Magellanic Cloud (LMC) present extended main-sequence turn-offs (MSTO) that have been attributed to either multiple stellar populations or an effect of stellar rotation. Recently it has been proposed that these extended main sequences can also be produced by ill-characterized stellar variability. Here we present Gemini-S/Gemini Multi-Object Spectrometer (GMOS) time series observations of the IA cluster NGC 1846. Using differential image analysis, we identified 73 new variable stars, with 55 of those being of the Delta Scuti type, that is, pulsating variables close the MSTO for the cluster age. Considering completeness and background contamination effects, we estimate the number of δ Sct belonging to the cluster between 40 and 60 members, although this number is based on the detection of a single δ Sct within the cluster half-light radius. This amount of variable stars at the MSTO level will not produce significant broadening of the MSTO, albeit higher-resolution imaging will be needed to rule out variable stars as a major contributor to the extended MSTO phenomenon. Though modest, this amount of δ Sct makes NGC 1846 the star cluster with the highest number of these variables ever discovered. Lastly, our results present a cautionary tale about the adequacy of shallow variability surveys in the LMC (like OGLE) to derive properties of its δ Sct population. Based on observations obtained at the Gemini Observatory, which is operated by the Association of Universities for Research in Astronomy, Inc., under a cooperative agreement with the NSF on behalf of the Gemini partnership: the National Science Foundation (United States), the National Research Council (Canada), CONICYT (Chile), Ministerio de Ciencia, Tecnología e Innovación Productiva (Argentina), and Ministério da Ciência, Tecnologia e Inovação (Brazil).

Spares Management : Optimizing Hardware Usage for the Space Shuttle Main Engine

NASA Technical Reports Server (NTRS)

Gulbrandsen, K. A.

1999-01-01

The complexity of the Space Shuttle Main Engine (SSME), combined with mounting requirements to reduce operations costs have increased demands for accurate tracking, maintenance, and projections of SSME assets. The SSME Logistics Team is developing an integrated asset management process. This PC-based tool provides a user-friendly asset database for daily decision making, plus a variable-input hardware usage simulation with complex logic yielding output that addresses essential asset management issues. Cycle times on critical tasks are significantly reduced. Associated costs have decreased as asset data quality and decision-making capability has increased.

Culture as a variable in neuroscience and clinical neuropsychology: A comprehensive review

PubMed Central

Wajman, José Roberto; Bertolucci, Paulo Henrique Ferreira; Mansur, Letícia Lessa; Gauthier, Serge

2015-01-01

Culture is a dynamic system of bidirectional influences among individuals and their environment, including psychological and biological processes, which facilitate adaptation and social interaction. One of the main challenges in clinical neuropsychology involves cognitive, behavioral and functional assessment of people with different sociocultural backgrounds. In this review essay, examining culture from a historical perspective to ethical issues in cross-cultural research, including the latest significant and publications, the authors sought to explore the main features related to cultural variables in neuropsychological practice and to debate the challenges found regarding the operational methods currently in use. Literature findings suggest a more comprehensive approach in cognitive and behavioral neuroscience, including an interface between elementary disciplines and applied neuropsychology. Thus, as a basis for discussion on this issue, the authors analyzed key-topics related to the study of new trends in sociocultural neuroscience and the application of their concepts from a clinical perspective. PMID:29213964

Searches for electromagnetic signals from extraterrestrial beings

NASA Astrophysics Data System (ADS)

Zuckerman, B.

The techniques and rationale used in six radio-frequency surveys to detect possible signals from extraterrestrial beings (ETs) are reviewed. Reception attempts have been made by pointing antennas at the stars within 80 light years, toward F, G, K, andd M main sequence stars, and binary star systems with component separation less than one-third or more than three times the radius of the habitable zone around the main star. All of the searches explored narrow bandwidths, with attention given to rapid variability. Stars exhibiting variability were re-examined for longer periods, using the 21 cm bandwidth, which is not used for transmissions on earth. The best spectrum analyzer in operation for ET signal search purposes has a capacity of 200,000 channels. Further studies may be carried out at the 10 micron IR wavelength, which could detect planetary-size construction projects by ET civilizations.

Comparative Effects of Antihistamines on Aircrew Mission Effectiveness under Sustained Operations

DTIC Science & Technology

1992-06-01

measures consist mainly of process measures. Process measures are measures of activities used to accomplish the mission and produce the final results...They include task completion times and response variability, and information processing rates as they relate to unique task assignment. Performance...contains process measures that assess the Individual contributions of hardware/software and human components to overall system performance. Measures

Variability in large-scale wind power generation: Variability in large-scale wind power generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kiviluoma, Juha; Holttinen, Hannele; Weir, David

2015-10-25

The paper demonstrates the characteristics of wind power variability and net load variability in multiple power systems based on real data from multiple years. Demonstrated characteristics include probability distribution for different ramp durations, seasonal and diurnal variability and low net load events. The comparison shows regions with low variability (Sweden, Spain and Germany), medium variability (Portugal, Ireland, Finland and Denmark) and regions with higher variability (Quebec, Bonneville Power Administration and Electric Reliability Council of Texas in North America; Gansu, Jilin and Liaoning in China; and Norway and offshore wind power in Denmark). For regions with low variability, the maximum 1more » h wind ramps are below 10% of nominal capacity, and for regions with high variability, they may be close to 30%. Wind power variability is mainly explained by the extent of geographical spread, but also higher capacity factor causes higher variability. It was also shown how wind power ramps are autocorrelated and dependent on the operating output level. When wind power was concentrated in smaller area, there were outliers with high changes in wind output, which were not present in large areas with well-dispersed wind power.« less

Position error compensation via a variable reluctance sensor applied to a Hybrid Vehicle Electric machine.

PubMed

Bucak, Ihsan Ömür

2010-01-01

In the automotive industry, electromagnetic variable reluctance (VR) sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV) system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion.

Position Error Compensation via a Variable Reluctance Sensor Applied to a Hybrid Vehicle Electric Machine

PubMed Central

Bucak, İhsan Ömür

2010-01-01

In the automotive industry, electromagnetic variable reluctance (VR) sensors have been extensively used to measure engine position and speed through a toothed wheel mounted on the crankshaft. In this work, an application that already uses the VR sensing unit for engine and/or transmission has been chosen to infer, this time, the indirect position of the electric machine in a parallel Hybrid Electric Vehicle (HEV) system. A VR sensor has been chosen to correct the position of the electric machine, mainly because it may still become critical in the operation of HEVs to avoid possible vehicle failures during the start-up and on-the-road, especially when the machine is used with an internal combustion engine. The proposed method uses Chi-square test and is adaptive in a sense that it derives the compensation factors during the shaft operation and updates them in a timely fashion. PMID:22294906

Identifying Human Factors Issues in Aircraft Maintenance Operations

NASA Technical Reports Server (NTRS)

Veinott, Elizabeth S.; Kanki, Barbara G.; Shafto, Michael G. (Technical Monitor)

1995-01-01

Maintenance operations incidents submitted to the Aviation Safety Reporting System (ASRS) between 1986-1992 were systematically analyzed in order to identify issues relevant to human factors and crew coordination. This exploratory analysis involved 95 ASRS reports which represented a wide range of maintenance incidents. The reports were coded and analyzed according to the type of error (e.g, wrong part, procedural error, non-procedural error), contributing factors (e.g., individual, within-team, cross-team, procedure, tools), result of the error (e.g., aircraft damage or not) as well as the operational impact (e.g., aircraft flown to destination, air return, delay at gate). The main findings indicate that procedural errors were most common (48.4%) and that individual and team actions contributed to the errors in more than 50% of the cases. As for operational results, most errors were either corrected after landing at the destination (51.6%) or required the flight crew to stop enroute (29.5%). Interactions among these variables are also discussed. This analysis is a first step toward developing a taxonomy of crew coordination problems in maintenance. By understanding what variables are important and how they are interrelated, we may develop intervention strategies that are better tailored to the human factor issues involved.

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

NASA Astrophysics Data System (ADS)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

The variable magnetic baffle as a control device for Kaufman thrusters.

NASA Technical Reports Server (NTRS)

Poeschel, R. L.

1972-01-01

The variable magnetic baffle described in this paper aids in control of electron flow from the hollow cathode plasma into the main discharge region by augmenting the fringe magnetic field which impedes this electron flow in conventionally baffled Kaufman thrusters. A passive, low loss, and automatic control device is obtained by using the discharge current to excite the control winding. Used in conjunction with typical thruster control loops, stable operation has been obtained over a 10:1 throttling range with a 30 cm thruster. Discharge ignition and overcurrent recycling is also facilitated through use of this device in a permanent magnet thruster.

Design Considerations for a New Terminal Area Arrival Scheduler

NASA Technical Reports Server (NTRS)

Thipphavong, Jane; Mulfinger, Daniel

2010-01-01

Design of a terminal area arrival scheduler depends on the interrelationship between throughput, delay and controller intervention. The main contribution of this paper is an analysis of the above interdependence for several stochastic behaviors of expected system performance distributions in the aircraft s time of arrival at the meter fix and runway. Results of this analysis serve to guide the scheduler design choices for key control variables. Two types of variables are analyzed, separation buffers and terminal delay margins. The choice for these decision variables was tested using sensitivity analysis. Analysis suggests that it is best to set the separation buffer at the meter fix to its minimum and adjust the runway buffer to attain the desired system performance. Delay margin was found to have the least effect. These results help characterize the variables most influential in the scheduling operations of terminal area arrivals.

Multimode delta Scuti stars in the open cluster NGC 7062

NASA Astrophysics Data System (ADS)

Freyhammer, L. M.; Arentoft, T.; Sterken, C.

2001-03-01

The central field of NGC 7062 was observed intensively with the main goal of finding delta Scuti stars suitable for use in asteroseismological tests of stellar structure and evolution theory. BV time series photometry was obtained for this northern open cluster, which has a large population of stars inside the delta Scuti instability strip, making it a probable host of several such variables. We report findings of 15 pulsating stars, including at least 13 delta Scuti stars. Ten variables oscillate in two or more frequencies. Only one of these variables was known before, for which we detected 9 frequencies. Five probable variables are mentioned, and period analysis is given for all 20 stars. Based on observations obtained at the Nordic Optical Telescope, operated on the island of La Palma jointly by Denmark, Finland, Iceland, Norway, and Sweden, in the Spanish Observatorio del Roque de los Muchachos of the Instituto de Astrofisíca de Canarias.

Real-time measurement system for evaluation of the carotid intima-media thickness with a robust edge operator.

PubMed

Faita, Francesco; Gemignani, Vincenzo; Bianchini, Elisabetta; Giannarelli, Chiara; Ghiadoni, Lorenzo; Demi, Marcello

2008-09-01

The purpose of this report is to describe an automatic real-time system for evaluation of the carotid intima-media thickness (CIMT) characterized by 3 main features: minimal interobserver and intraobserver variability, real-time capabilities, and great robustness against noise. One hundred fifty carotid B-mode ultrasound images were used to validate the system. Two skilled operators were involved in the analysis. Agreement with the gold standard, defined as the mean of 2 manual measurements of a skilled operator, and the interobserver and intraobserver variability were quantitatively evaluated by regression analysis and Bland-Altman statistics. The automatic measure of the CIMT showed a mean bias +/- SD of 0.001 +/- 0.035 mm toward the manual measurement. The intraobserver variability, evaluated with Bland-Altman plots, showed a bias that was not significantly different from 0, whereas the SD of the differences was greater in the manual analysis (0.038 mm) than in the automatic analysis (0.006 mm). For interobserver variability, the automatic measurement had a bias that was not significantly different from 0, with a satisfactory SD of the differences (0.01 mm), whereas in the manual measurement, a little bias was present (0.012 mm), and the SD of the differences was noticeably greater (0.044 mm). The CIMT has been accepted as a noninvasive marker of early vascular alteration. At present, the manual approach is largely used to estimate CIMT values. However, that method is highly operator dependent and time-consuming. For these reasons, we developed a new system for the CIMT measurement that conjugates precision with real-time analysis, thus providing considerable advantages in clinical practice.

Power and energy ratios in mechanical CVT drive control

NASA Astrophysics Data System (ADS)

Balakin, P. D.; Stripling, L. O.

2017-06-01

Being based on the principle of providing the systems with adaptation property to the real parameters and operational condition, the mechanical system capable to control automatically the components of convertible power is offered and this allows providing stationary operation of the vehicle engine in the terms of variable external loading. This is achieved by drive control integrated in the power transmission, which implements an additional degree of freedom and operates on the basis of the laws of motion, with the energy of the main power flow by changing automatically the kinematic characteristics of the power transmission, this system being named CVT. The power and energy ratios found allow performing the necessary design calculations of the sections and the links of the mechanical CVT scheme.

Hybrid quantum computing with ancillas

NASA Astrophysics Data System (ADS)

Proctor, Timothy J.; Kendon, Viv

2016-10-01

In the quest to build a practical quantum computer, it is important to use efficient schemes for enacting the elementary quantum operations from which quantum computer programs are constructed. The opposing requirements of well-protected quantum data and fast quantum operations must be balanced to maintain the integrity of the quantum information throughout the computation. One important approach to quantum operations is to use an extra quantum system - an ancilla - to interact with the quantum data register. Ancillas can mediate interactions between separated quantum registers, and by using fresh ancillas for each quantum operation, data integrity can be preserved for longer. This review provides an overview of the basic concepts of the gate model quantum computer architecture, including the different possible forms of information encodings - from base two up to continuous variables - and a more detailed description of how the main types of ancilla-mediated quantum operations provide efficient quantum gates.

An Experts Survey on Sustainability Across Twenty-Seven Extensive European Systems of Grassland Management

NASA Astrophysics Data System (ADS)

Caballero, Rafael; Gil, Ángel; Fernández-Santos, Xavier

2008-08-01

European Large Scale Grazing Systems (LSGS) are at a crossroad with environmental, agronomic, and social factors interacting on their future viability. This research assesses the current environmental and socio-economic status of a wide range of European LSGS according to an agreed subset of sustainability criteria and indicators, which have been recognized by corresponding experts and privileged observers on their respective case-study system. A survey questionnaire was drafted containing five main criteria (pastoral use, environmental, economic, social, and market and development), with four conceptual-scored variables (indicators) within each criterion. Descriptive, analytical and clustering statistical techniques helped to draw a synthesis of the main result and to standardize sustainability variables across different biogeographical regions and management situations. The results show large multicollinearity among the 20 variables proposed. This dependence was revealed by the reduction to six main factor-components, which accounted for about 73% of the total variance in responses. Aggregation of point-score indicators across criteria to obtain a sustainability index can be of less policy relevance than responses to specific criteria or indicators. Affinity between case-study systems, as judged by collaborative-expert responses, was not related to biogeographical location, operating livestock sector, or population density in their areas. The results show larger weaknesses and constraints in the economic and social criteria than in the pastoral and environmental criteria, and the large heterogeneity of responses appears in the social criterion.

Technical aspects of virtual liver resection planning.

PubMed

Glombitza, G; Lamadé, W; Demiris, A M; Göpfert, M R; Mayer, A; Bahner, M L; Meinzer, H P; Richter, G; Lehnert, T; Herfarth, C

1998-01-01

Operability of a liver tumor is depending on its three dimensional relation to the intrahepatic vascular trees which define autonomously functioning liver (sub-)segments. Precise operation planning is complicated by anatomic variability, distortion of the vascular trees by the tumor or preceding liver resections. Because of the missing possibility to track the deformation of the liver during the operation an integration of the resection planning system into an intra-operative navigation system is not feasible. So the main task of an operation planning system in this domain is a quantifiable patient selection by exact prediction of post-operative liver function and a quantifiable resection proposal. The system quantifies the organ structures and resection volumes by means of absolute and relative values. It defines resection planes depending on security margins and the vascular trees and presents the data in visualized form as a 3D movie. The new 3D operation planning system offers quantifiable liver resection proposals based on individualized liver anatomy. The results are visualized in digital movies as well as in quantitative reports.

Factors that affect the permeability of commercial hollow-fibre membranes in a submerged anaerobic MBR (HF-SAnMBR) system.

PubMed

Robles, A; Ruano, M V; Ribes, J; Ferrer, J

2013-03-01

A demonstration plant with two commercial HF ultrafiltration membrane modules (PURON(®), Koch Membrane Systems, PUR-PSH31) was operated with urban wastewater. The effect of the main operating variables on membrane performance at sub-critical and supra-critical filtration conditions was tested. The physical operating variables that affected membrane performance most were gas sparging intensity and back-flush (BF) frequency. Indeed, low gas sparging intensities (around 0.23 Nm(3) h(-1) m(-2)) and low BF frequencies (30-s back-flush for every 10 basic filtration-relaxation cycles) were enough to enable membranes to be operated sub-critically even when levels of mixed liquor total solids were high (up to 25 g L(-1)). On the other hand, significant gas sparging intensities and BF frequencies were required in order to maintain long-term operating at supra-critical filtration conditions. After operating for more than two years at sub-critical conditions (transmembrane flux between 9 and 13.3 LMH at gas sparging intensities of around 0.23 Nm(3) h(-1) m(-2) and MLTS levels from around 10-30 g L(-1)) no significant irreversible/irrecoverable fouling problems were detected (membrane permeability remained above 100 LMH bar(-1) and total filtration resistance remained below 10(13) m(-1)), therefore no chemical cleaning was conducted. Membrane performance was similar to the aerobic HF membranes operated in full-scale MBR plants. Copyright © 2012 Elsevier Ltd. All rights reserved.

Exactly and quasi-exactly solvable 'discrete' quantum mechanics.

PubMed

Sasaki, Ryu

2011-03-28

A brief introduction to discrete quantum mechanics is given together with the main results on various exactly solvable systems. Namely, the intertwining relations, shape invariance, Heisenberg operator solutions, annihilation/creation operators and dynamical symmetry algebras, including the q-oscillator algebra and the Askey-Wilson algebra. A simple recipe to construct exactly and quasi-exactly solvable (QES) Hamiltonians in one-dimensional 'discrete' quantum mechanics is presented. It reproduces all the known Hamiltonians whose eigenfunctions consist of the Askey scheme of hypergeometric orthogonal polynomials of a continuous or a discrete variable. Several new exactly and QES Hamiltonians are constructed. The sinusoidal coordinate plays an essential role.

Prognostic scores in oesophageal or gastric variceal bleeding.

PubMed

Ohmann, C; Stöltzing, H; Wins, L; Busch, E; Thon, K

1990-05-01

Numerous scoring systems have been developed for the prediction of outcome of variceal bleeding; however, only a few have been evaluated adequately. The object of this study was to improve the classical Child-Pugh score (CPS) and to test other scores from the literature. Patients (n = 82) with endoscopically confirmed variceal bleeding and long-term sclerotherapy were included in the study. Linear logistic regression (LR) was applied to different sets of prognostic variables with regard to 30-day mortality. In addition, scores from the literature were evaluated on the data set. Performance was measured by the accuracy and receiver-operating characteristic curves. The application of LR to all five CPS variables (accuracy, 80%) was superior to the classical CPS (70%). LR with selection from the CPS variables or from other sets of variables resulted in no improvement. Compared with CPS only three scores from the literature, mainly based on subsets of the CPS variables, showed an improved accuracy. It is concluded that CPS is still a good scoring system; however, it can be improved by statistical analysis using the same variables.

Constraints, Trade-offs and the Currency of Fitness.

PubMed

Acerenza, Luis

2016-03-01

Understanding evolutionary trajectories remains a difficult task. This is because natural evolutionary processes are simultaneously affected by various types of constraints acting at the different levels of biological organization. Of particular importance are constraints where correlated changes occur in opposite directions, called trade-offs. Here we review and classify the main evolutionary constraints and trade-offs, operating at all levels of trait hierarchy. Special attention is given to life history trade-offs and the conflict between the survival and reproduction components of fitness. Cellular mechanisms underlying fitness trade-offs are described. At the metabolic level, a linear trade-off between growth and flux variability was found, employing bacterial genome-scale metabolic reconstructions. Its analysis indicates that flux variability can be considered as the currency of fitness. This currency is used for fitness transfer between fitness components during adaptations. Finally, a discussion is made regarding the constraints which limit the increase in the amount of fitness currency during evolution, suggesting that occupancy constraints are probably the main restrictions.

[Variables involved in the individual and collective practice of healthy habits].

PubMed

García-Ubaque, Juan C; García-Ubaque, César A; Vaca-Bohórquez, Martha L

2014-01-01

To conduct a descriptive review of the concepts related to the practice of healthy habits by identifying the main variables associated with their managment in terms of health promotion actions. In consultation with groups working in health promotion in the city of performed by consulting databases and documentary sources. The strategy and criteria for the selection of documents was previously defined. Finally, we proceeded to organizing and structuring the information. It was established that, to promote healthy habits, four groups of behavior are involved: a) consumption, b) phyisical activity and hygiene, c) safety, and d) social participation. All of these are reviewed in order to point out the main concepts contained in each. The promotion of healthy habits must involve not only the transmission of behaviors associated with them. It must also involve understanding and adapting these habits to the environments of life in which people operate, with consideration for the different roles that they perform and the psychological and cultural demands that each space implies.

Quantum hacking of two-way continuous-variable quantum key distribution using Trojan-horse attack

NASA Astrophysics Data System (ADS)

Ma, Hong-Xin; Bao, Wan-Su; Li, Hong-Wei; Chou, Chun

2016-08-01

We present a Trojan-horse attack on the practical two-way continuous-variable quantum key distribution system. Our attack mainly focuses on the imperfection of the practical system that the modulator has a redundancy of modulation pulse-width, which leaves a loophole for the eavesdropper inserting a Trojan-horse pulse. Utilizing the unique characteristics of two-way continuous-variable quantum key distribution that Alice only takes modulation operation on the received mode without any measurement, this attack allows the eavesdropper to render all of the final keys shared between the legitimate parties insecure without being detected. After analyzing the feasibility of the attack, the corresponding countermeasures are put forward. Project supported by the National Basic Research Program of China (Grant No. 2013CB338002) and the National Natural Science Foundation of China (Grant Nos. 11304397 and 61505261).

Dual stator winding variable speed asynchronous generator: optimal design and experiments

NASA Astrophysics Data System (ADS)

Tutelea, L. N.; Deaconu, S. I.; Popa, G. N.

2015-06-01

In the present paper is carried out a theoretical and experimental study of dual stator winding squirrel cage asynchronous generator (DSWA) behavior in the presence of saturation regime (non-sinusoidal) due to the variable speed operation. The main aims are the determination of the relations of calculating the equivalent parameters of the machine windings to optimal design using a Matlab code. Issue is limited to three phase range of double stator winding cage-induction generator of small sized powers, the most currently used in the small adjustable speed wind or hydro power plants. The tests were carried out using three-phase asynchronous generator having rated power of 6 [kVA].

Statistical analysis for understanding and predicting battery degradations in real-life electric vehicle use

NASA Astrophysics Data System (ADS)

Barré, Anthony; Suard, Frédéric; Gérard, Mathias; Montaru, Maxime; Riu, Delphine

2014-01-01

This paper describes the statistical analysis of recorded data parameters of electrical battery ageing during electric vehicle use. These data permit traditional battery ageing investigation based on the evolution of the capacity fade and resistance raise. The measured variables are examined in order to explain the correlation between battery ageing and operating conditions during experiments. Such study enables us to identify the main ageing factors. Then, detailed statistical dependency explorations present the responsible factors on battery ageing phenomena. Predictive battery ageing models are built from this approach. Thereby results demonstrate and quantify a relationship between variables and battery ageing global observations, and also allow accurate battery ageing diagnosis through predictive models.

Development of the integrated control system for the microwave ion source of the PEFP 100-MeV proton accelerator

NASA Astrophysics Data System (ADS)

Song, Young-Gi; Seol, Kyung-Tae; Jang, Ji-Ho; Kwon, Hyeok-Jung; Cho, Yong-Sub

2012-07-01

The Proton Engineering Frontier Project (PEFP) 20-MeV proton linear accelerator is currently operating at the Korea Atomic Energy Research Institute (KAERI). The ion source of the 100-MeV proton linac needs at least a 100-hour operation time. To meet the goal, we have developed a microwave ion source that uses no filament. For the ion source, a remote control system has been developed by using experimental physics and the industrial control system (EPICS) software framework. The control system consists of a versa module europa (VME) and EPICS-based embedded applications running on a VxWorks real-time operating system. The main purpose of the control system is to control and monitor the operational variables of the components remotely and to protect operators from radiation exposure and the components from critical problems during beam extraction. We successfully performed the operation test of the control system to confirm the degree of safety during the hardware performance.

Control Design for an Advanced Geared Turbofan Engine

NASA Technical Reports Server (NTRS)

Chapman, Jeffryes W.; Litt, Jonathan S.

2017-01-01

This paper describes the design process for the control system of an advanced geared turbofan engine. This process is applied to a simulation that is representative of a 30,000 lbf thrust class concept engine with two main spools, ultra-high bypass ratio, and a variable area fan nozzle. Control system requirements constrain the non-linear engine model as it operates throughout its flight envelope of sea level to 40,000 ft and from 0 to 0.8 Mach. The control architecture selected for this project was developed from literature and reflects a configuration that utilizes a proportional integral controller integrated with sets of limiters that enable the engine to operate safely throughout its flight envelope. Simulation results show the overall system meets performance requirements without exceeding system operational limits.

Transient thermal analysis for radioactive liquid mixing operations in a large-scaled tank

DOE PAGES

Lee, S. Y.; Smith, III, F. G.

2014-07-25

A transient heat balance model was developed to assess the impact of a Submersible Mixer Pump (SMP) on radioactive liquid temperature during the process of waste mixing and removal for the high-level radioactive materials stored in Savannah River Site (SRS) tanks. The model results will be mainly used to determine the SMP design impacts on the waste tank temperature during operations and to develop a specification for a new SMP design to replace existing longshaft mixer pumps used during waste removal. The present model was benchmarked against the test data obtained by the tank measurement to examine the quantitative thermalmore » response of the tank and to establish the reference conditions of the operating variables under no SMP operation. The results showed that the model predictions agreed with the test data of the waste temperatures within about 10%.« less

Optimization of Sinter Plant Operating Conditions Using Advanced Multivariate Statistics: Intelligent Data Processing

NASA Astrophysics Data System (ADS)

Fernández-González, Daniel; Martín-Duarte, Ramón; Ruiz-Bustinza, Íñigo; Mochón, Javier; González-Gasca, Carmen; Verdeja, Luis Felipe

2016-08-01

Blast furnace operators expect to get sinter with homogenous and regular properties (chemical and mechanical), necessary to ensure regular blast furnace operation. Blends for sintering also include several iron by-products and other wastes that are obtained in different processes inside the steelworks. Due to their source, the availability of such materials is not always consistent, but their total production should be consumed in the sintering process, to both save money and recycle wastes. The main scope of this paper is to obtain the least expensive iron ore blend for the sintering process, which will provide suitable chemical and mechanical features for the homogeneous and regular operation of the blast furnace. The systematic use of statistical tools was employed to analyze historical data, including linear and partial correlations applied to the data and fuzzy clustering based on the Sugeno Fuzzy Inference System to establish relationships among the available variables.

An Advanced Framework for Improving Situational Awareness in Electric Power Grid Operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Yousu; Huang, Zhenyu; Zhou, Ning

With the deployment of new smart grid technologies and the penetration of renewable energy in power systems, significant uncertainty and variability is being introduced into power grid operation. Traditionally, the Energy Management System (EMS) operates the power grid in a deterministic mode, and thus will not be sufficient for the future control center in a stochastic environment with faster dynamics. One of the main challenges is to improve situational awareness. This paper reviews the current status of power grid operation and presents a vision of improving wide-area situational awareness for a future control center. An advanced framework, consisting of parallelmore » state estimation, state prediction, parallel contingency selection, parallel contingency analysis, and advanced visual analytics, is proposed to provide capabilities needed for better decision support by utilizing high performance computing (HPC) techniques and advanced visual analytic techniques. Research results are presented to support the proposed vision and framework.« less

Installation of PMV Operation Program in DDC Controller and Air Conditioning Control Using PMV Directly as Set Point

NASA Astrophysics Data System (ADS)

Haramoto, Ken-Ichi

In general, air conditioning control in a building is operated mainly by indoor air temperature control. Although the operators of the machine in the building accepted a claim for indoor air temperature presented by the building inhabitants, the indoor conditions have been often too cool or warm. Therefore, in an attempt to create better thermal environments, the author paid attention to the PMV that is a thermal comfort index. And then, the possibility of air conditioning control using the PMV directly as the set point was verified by employing actual equipment in an air conditioning testing room and an office building. Prior to the execution of this control, the operation program of the PMV was installed in a DDC controller for the air conditioning control. And information from indoor sensors and so on was inputted to the controller, and the computed PMV was used as the feedback variable.

Pilot Perception of Electronic Flight Bags at Part 121 Air Carriers

NASA Astrophysics Data System (ADS)

Lytle, Donley

Electronic Flight Bags (EFBs) have been approved for use by pilots in flight operations at many Part 121 air carriers in the United States since 2010. As an automated device replacing paper in the cockpit, there are many human factor issues that relate to operation of the EFB. EFBs have been cited in accidents and incidents worldwide in large, transport category aircraft. While the EFB was not cited as the main cause of the accident/incident, it has been listed as a contributing factor. This study looks at pilot perception related to the safety aspect of the EFB in flight operations at Part 121 carriers in the United States. It surveys pilots that utilize the device in daily, routine flight operations to determine their perception of the EFB. The study is followed with a survey of a small group of pilots to help explain the results and any correlation between the variables.

Tacholess order-tracking approach for wind turbine gearbox fault detection

NASA Astrophysics Data System (ADS)

Wang, Yi; Xie, Yong; Xu, Guanghua; Zhang, Sicong; Hou, Chenggang

2017-09-01

Monitoring of wind turbines under variable-speed operating conditions has become an important issue in recent years. The gearbox of a wind turbine is the most important transmission unit; it generally exhibits complex vibration signatures due to random variations in operating conditions. Spectral analysis is one of the main approaches in vibration signal processing. However, spectral analysis is based on a stationary assumption and thus inapplicable to the fault diagnosis of wind turbines under variable-speed operating conditions. This constraint limits the application of spectral analysis to wind turbine diagnosis in industrial applications. Although order-tracking methods have been proposed for wind turbine fault detection in recent years, current methods are only applicable to cases in which the instantaneous shaft phase is available. For wind turbines with limited structural spaces, collecting phase signals with tachometers or encoders is difficult. In this study, a tacholess order-tracking method for wind turbines is proposed to overcome the limitations of traditional techniques. The proposed method extracts the instantaneous phase from the vibration signal, resamples the signal at equiangular increments, and calculates the order spectrum for wind turbine fault identification. The effectiveness of the proposed method is experimentally validated with the vibration signals of wind turbines.

Variable-Speed Power-Turbine Research at Glenn Research Center

NASA Technical Reports Server (NTRS)

Welch, Gerard E.; McVetta, Ashlie B.; Stevens, Mark A.; Howard, Samuel A.; Giel, Paul W.; Ameri, Ali, A.; To, Waiming; Skoch, Gary J.; Thurman, Douglas R.

2012-01-01

The main rotors of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle operate over a wide speed-range, from 100 percent at takeoff to 54 percent at cruise. The variable-speed power turbine (VSPT) offers one approach by which to effect this speed variation. VSPT aerodynamics challenges include high work factors at cruise, wide (40 to 60 ) incidence-angle variations in blade and vane rows over the speed range, and operation at low Reynolds numbers. Rotordynamics challenges include potential responsiveness to shaft modes within the 50 percent VSPT speed-range. A research effort underway at NASA Glenn Research Center, intended to address these key aerodynamic and rotordynamic challenges, is described. Conceptual design and 3-D multistage RANS and URANS analyses, conducted internally and under contract, provide expected VSPT sizing, stage-count, performance and operability information, and maps for system studies. Initial steps toward experimental testing of incidence-tolerant blading in a transonic linear cascade are described, and progress toward development/improvement of a simulation capability for multistage turbines with low Reynolds number transitional flow is summarized. Preliminary rotordynamics analyses indicate that viable concept engines with 50 percent VSPT shaft-speed range. Assessments of potential paths toward VSPT component-level testing are summarized.

Probabilistic structural analysis methods for improving Space Shuttle engine reliability

NASA Technical Reports Server (NTRS)

Boyce, L.

1989-01-01

Probabilistic structural analysis methods are particularly useful in the design and analysis of critical structural components and systems that operate in very severe and uncertain environments. These methods have recently found application in space propulsion systems to improve the structural reliability of Space Shuttle Main Engine (SSME) components. A computer program, NESSUS, based on a deterministic finite-element program and a method of probabilistic analysis (fast probability integration) provides probabilistic structural analysis for selected SSME components. While computationally efficient, it considers both correlated and nonnormal random variables as well as an implicit functional relationship between independent and dependent variables. The program is used to determine the response of a nickel-based superalloy SSME turbopump blade. Results include blade tip displacement statistics due to the variability in blade thickness, modulus of elasticity, Poisson's ratio or density. Modulus of elasticity significantly contributed to blade tip variability while Poisson's ratio did not. Thus, a rational method for choosing parameters to be modeled as random is provided.

Electronic magnification for astronomical camera tubes

NASA Technical Reports Server (NTRS)

Vine, J.; Hansen, J. R.; Pietrzyk, J. P.

1974-01-01

Definitions, test schemes, and analyses used to provide variable magnification in the image section of the television sensor for large space telescopes are outlined. Experimental results show a definite form of magnetic field distribution is necessary to achieve magnification in the range 3X to 4X. Coil systems to establish the required field shapes were built, and both image intensifiers and camera tubes were operated at high magnification. The experiments confirm that such operation is practical and can provide satisfactory image quality. The main problem with such a system was identified as heating of the photocathode due to concentration of coil power dissipation in that vicinity. Suggestions for overcoming this disadvantage are included.

[Occupational accidents in an oil refinery in Brazil].

PubMed

Souza, Carlos Augusto Vaz de; Freitas, Carlos Machado de

2002-10-01

Work in oil refineries involves the risk of minor to major accidents. National data show the impact of accidents on this industry. A study was carried out to describe accident profile and evaluate the adequacy of accident reporting system. Data on all accidents reported in an oil refinery in the state of Rio de Janeiro for the year 1997 were organized and analyzed. The study population consisted of 153 injury cases, 83 hired and 69 contracted workers. The variables were: type of accident, operation mode and position of the worker injured. Among hired workers, minor accidents predominated (54.2%) and they occurred during regular operation activities (62.9%). Among contracted workers, there also predominated minor accidents (75.5%) in a higher percentage, but they occurred mainly during maintenance activities (96.8%). The study results showed that there is a predominance of accidents in lower hierarchy workers, and these accidents occur mainly during maintenance activities. There is a need to improve the company's accident reporting system and accident investigation procedures.

Linear dynamical modes as new variables for data-driven ENSO forecast

NASA Astrophysics Data System (ADS)

Gavrilov, Andrey; Seleznev, Aleksei; Mukhin, Dmitry; Loskutov, Evgeny; Feigin, Alexander; Kurths, Juergen

2018-05-01

A new data-driven model for analysis and prediction of spatially distributed time series is proposed. The model is based on a linear dynamical mode (LDM) decomposition of the observed data which is derived from a recently developed nonlinear dimensionality reduction approach. The key point of this approach is its ability to take into account simple dynamical properties of the observed system by means of revealing the system's dominant time scales. The LDMs are used as new variables for empirical construction of a nonlinear stochastic evolution operator. The method is applied to the sea surface temperature anomaly field in the tropical belt where the El Nino Southern Oscillation (ENSO) is the main mode of variability. The advantage of LDMs versus traditionally used empirical orthogonal function decomposition is demonstrated for this data. Specifically, it is shown that the new model has a competitive ENSO forecast skill in comparison with the other existing ENSO models.

Artificial immune system via Euclidean Distance Minimization for anomaly detection in bearings

NASA Astrophysics Data System (ADS)

Montechiesi, L.; Cocconcelli, M.; Rubini, R.

2016-08-01

In recent years new diagnostics methodologies have emerged, with particular interest into machinery operating in non-stationary conditions. In fact continuous speed changes and variable loads make non-trivial the spectrum analysis. A variable speed means a variable characteristic fault frequency related to the damage that is no more recognizable in the spectrum. To overcome this problem the scientific community proposed different approaches listed in two main categories: model-based approaches and expert systems. In this context the paper aims to present a simple expert system derived from the mechanisms of the immune system called Euclidean Distance Minimization, and its application in a real case of bearing faults recognition. The proposed method is a simplification of the original process, adapted by the class of Artificial Immune Systems, which proved to be useful and promising in different application fields. Comparative results are provided, with a complete explanation of the algorithm and its functioning aspects.

Influence of the South-to-North Water Transfer and the Yangtze River Mitigation Projects on the water quality of Han River, China

NASA Astrophysics Data System (ADS)

Liu, W.; Kuo, Y. M.

2016-12-01

The Middle Route of China's South-to-North Water Transfer (MSNW) and Yangtze-Han River Water Diversion (YHWD) Projects have been operated since 2014, which may deteriorate water quality in Han River. The 11 water sampling sites distributed from the middle and down streams of Han River watershed were monitored monthly between July 2014 and December 2015. Factor analysis and cluster analysis were applied to investigate the major pollution types and main variables influencing water quality in Han River. The factor analysis distinguishes three main pollution types (agricultural nonpoint source, organic, and phosphorus point source pollution) affecting water quality of Han River. Cluster analysis classified all sampling sites into four groups and determined their pollution source for both Dry and Wet seasons. The sites located at central city receive point source pollution in both seasons. The water quality in downstream Han River (excluding central city sites) was influenced by nonpoint source pollution from Jianghan Plain. Variations of water qualities are associated with hydrological conditions varied from operations of engineering projects and seasonal variability especially in Dry season. Good water quality as Class III mainly occurred when flow rate is greater than 800 cms in Dry season. The low average flow rate below 583 cms will degrade water quality as Class V at almost all sites. Elevating the flow rate discharged from MSNW and YHWD Projects to Han River can avoid degrading water quality especially in low flow conditions and may decrease the probability of algal bloom occurrence in Han River. Increasing the flow rate from 400 cms to 700 cms in main Han River can obviously improve the water quality of Han River. The investigation of relationships between water quality and flow rate in both projects can provide management strategies of water quality for various flow conditions.

Variable Temperature Blackbodies via Variable Conductance: Thermal Design, Modelling and Testing

NASA Astrophysics Data System (ADS)

Melzack, N.; Jones, E.; Peters, D. M.; Hurley, J. G.; Watkins, R. E. J.; Fok, S.; Sawyer, C.; Marchetaux, G.; Acreman, A.; Winkler, R.; Lowe, D.; Theocharous, T.; Montag, V.; Gibbs, D.; Pearce, A. B.; Bishop, G.; Newman, E.; Keen, S.; Stokes, J.; Pearce, A.; Stamper, R.; Cantell-Hynes, A.

2017-02-01

This paper presents the overall design for large (˜ 400 mm aperture) reference blackbody cavities currently under development at the Science and Technology Facilities Council Rutherford Appleton Laboratory Space Department (STFC RAL Space), in collaboration with the National Physical Laboratory (NPL). These blackbodies are designed to operate in vacuum over a temperature range from 160 K to 370 K, with an additional capability to operate at ˜ 100 K as a point of near-zero radiance. This is a challenging problem for a single blackbody. The novel thermal design presented in this paper enables one target that can physically achieve and operate successfully at both thermal extremes, whilst also meeting stringent temperature gradient requirements. The overall blackbody design is based upon a helium gas-gap heat switch and modified to allow for variable thermal conductance. The blackbody design consists of three main concentric cylinder components—an inner cavity (aluminium alloy), a radiation shield (aluminium) and an outer liquid nitrogen (LN2) jacket (stainless steel). The internal surface of the cavity is the effective radiating surface. There is a helium gas interspace surrounding the radiation shield and enclosed by the LN2 jacket and the inner cavity. The blackbodies are now at a mature stage of development. In this paper, the overall design, focusing upon the thermal design solution, is detailed. This paper will also concern the full-scale prototype breadboard model, for which results on thermal stability, spatial gradients and other sensitivities will be presented.

Development of probabilistic operating rules for Hluhluwe Dam, South Africa

NASA Astrophysics Data System (ADS)

Ndiritu, J.; Odiyo, J.; Makungo, R.; Mwaka, B.; Mthethwa, N.; Ntuli, C.; Andanje, A.

2017-08-01

Hluhluwe Dam, with a 30 million m3 reservoir that supplies water for irrigation and Hluhluwe municipality in Kwa-Zulu Natal Province, South Africa, was consistently experiencing low storage levels over several non-drought years since 2001. The dam was operated by rules of thumb and there were no records of water releases for irrigation - the main user of the dam. This paper describes an assessment of the historic behaviour of the reservoir since its completion in 1964 and the development of operating rules that accounted for: i) the multiple and different levels of reliability at which municipal and irrigation demands need to be supplied, and ii) inter-annual and inter-decadal variability of climate and inflows into the dam. The assessment of the behaviour of the reservoir was done by simulation assuming trigonometric rule curves that were optimized to maximize both yield and storage state using the SCE-UA method. The resulting reservoir behaviour matched the observed historic trajectory reasonably well and indicated that the dam has mainly been operated at a demand of 10 million m3/year until 2000 when the demand suddenly rose to 25 million m3/year. Operating rules were developed from a statistical analysis of the base yields from 500 simulations of the reservoir each using 5 year-long stochastically generated sequences of inflows, rainfall and evaporation. After the implementation of the operating rules in 2009, the storage state of the dam improved and matched those of other reservoirs in the region that had established operating rules.

Inter Annual Variability of the California Current System and Associated Biochemical Characteristics from Prolonged Data Series

DTIC Science & Technology

2016-06-01

onto the eastern north Pacific circulation has been studied for years, the effect of El Nino Modoki in the region is still unclear. The CCS is...ready for combat. The main mission of Third Fleet is to provide safe, effective , relevant training to ensure Sailors have the essential skills to...Fleet. Understanding our environment and ocean currents with in the CCS improves the Navy’s ability to practice operating safely and effectively along

A retrospective analysis of laparoscopic partial nephrectomy with segmental renal artery clamping and factors that predict postoperative renal function.

PubMed

Li, Pu; Qin, Chao; Cao, Qiang; Li, Jie; Lv, Qiang; Meng, Xiaoxin; Ju, Xiaobing; Tang, Lijun; Shao, Pengfei

2016-10-01

To evaluate the feasibility and efficiency of laparoscopic partial nephrectomy (LPN) with segmental renal artery clamping, and to analyse the factors affecting postoperative renal function. We conducted a retrospective analysis of 466 consecutive patients undergoing LPN using main renal artery clamping (group A, n = 152) or segmental artery clamping (group B, n = 314) between September 2007 and July 2015 in our department. Blood loss, operating time, warm ischaemia time (WIT) and renal function were compared between groups. Univariable and multivariable linear regression analyses were applied to assess the correlations of selected variables with postoperative glomerular filtration rate (GFR) reduction. Volumetric data and estimated GFR of a subset of 60 patients in group B were compared with GFR to evaluate the correlation between these functional variables and preserved renal function after LPN. The novel technique slightly increased operating time, WIT and intra-operative blood loss (P < 0.001), while it provided better postoperative renal function (P < 0.001) compared with the conventional technique. The blocking method and tumour characteristics were independent factors affecting GFR reduction, while WIT was not an independent factor. Correlation analysis showed that estimated GFR presented better correlation with GFR compared with kidney volume (R(2) = 0.794 cf. R(2) = 0.199) in predicting renal function after LPN. LPN with segmental artery clamping minimizes warm ischaemia injury and provides better early postoperative renal function compared with clamping the main renal artery. Kidney volume has a significantly inferior role compared with eGFR in predicting preserved renal function. © 2016 The Authors BJU International © 2016 BJU International Published by John Wiley & Sons Ltd.

Computer experimental analysis of the CHP performance of a 100 kW e SOFC Field Unit by a factorial design

NASA Astrophysics Data System (ADS)

Calì, M.; Santarelli, M. G. L.; Leone, P.

Gas Turbine Technologies (GTT) and Politecnico di Torino, both located in Torino (Italy), have been involved in the design and installation of a SOFC laboratory in order to analyse the operation, in cogenerative configuration, of the CHP 100 kW e SOFC Field Unit, built by Siemens-Westinghouse Power Corporation (SWPC), which is at present (May 2005) starting its operation and which will supply electric and thermal power to the GTT factory. In order to take the better advantage from the analysis of the on-site operation, and especially to correctly design the scheduled experimental tests on the system, we developed a mathematical model and run a simulated experimental campaign, applying a rigorous statistical approach to the analysis of the results. The aim of this work is the computer experimental analysis, through a statistical methodology (2 k factorial experiments), of the CHP 100 performance. First, the mathematical model has been calibrated with the results acquired during the first CHP100 demonstration at EDB/ELSAM in Westerwoort. After, the simulated tests have been performed in the form of computer experimental session, and the measurement uncertainties have been simulated with perturbation imposed to the model independent variables. The statistical methodology used for the computer experimental analysis is the factorial design (Yates' Technique): using the ANOVA technique the effect of the main independent variables (air utilization factor U ox, fuel utilization factor U F, internal fuel and air preheating and anodic recycling flow rate) has been investigated in a rigorous manner. Analysis accounts for the effects of parameters on stack electric power, thermal recovered power, single cell voltage, cell operative temperature, consumed fuel flow and steam to carbon ratio. Each main effect and interaction effect of parameters is shown with particular attention on generated electric power and stack heat recovered.

Method of operating a thermoelectric generator

DOEpatents

Reynolds, Michael G; Cowgill, Joshua D

2013-11-05

A method for operating a thermoelectric generator supplying a variable-load component includes commanding the variable-load component to operate at a first output and determining a first load current and a first load voltage to the variable-load component while operating at the commanded first output. The method also includes commanding the variable-load component to operate at a second output and determining a second load current and a second load voltage to the variable-load component while operating at the commanded second output. The method includes calculating a maximum power output of the thermoelectric generator from the determined first load current and voltage and the determined second load current and voltage, and commanding the variable-load component to operate at a third output. The commanded third output is configured to draw the calculated maximum power output from the thermoelectric generator.

Bayesian hierarchical modelling of North Atlantic windiness

NASA Astrophysics Data System (ADS)

Vanem, E.; Breivik, O. N.

2013-03-01

Extreme weather conditions represent serious natural hazards to ship operations and may be the direct cause or contributing factor to maritime accidents. Such severe environmental conditions can be taken into account in ship design and operational windows can be defined that limits hazardous operations to less extreme conditions. Nevertheless, possible changes in the statistics of extreme weather conditions, possibly due to anthropogenic climate change, represent an additional hazard to ship operations that is less straightforward to account for in a consistent way. Obviously, there are large uncertainties as to how future climate change will affect the extreme weather conditions at sea and there is a need for stochastic models that can describe the variability in both space and time at various scales of the environmental conditions. Previously, Bayesian hierarchical space-time models have been developed to describe the variability and complex dependence structures of significant wave height in space and time. These models were found to perform reasonably well and provided some interesting results, in particular, pertaining to long-term trends in the wave climate. In this paper, a similar framework is applied to oceanic windiness and the spatial and temporal variability of the 10-m wind speed over an area in the North Atlantic ocean is investigated. When the results from the model for North Atlantic windiness is compared to the results for significant wave height over the same area, it is interesting to observe that whereas an increasing trend in significant wave height was identified, no statistically significant long-term trend was estimated in windiness. This may indicate that the increase in significant wave height is not due to an increase in locally generated wind waves, but rather to increased swell. This observation is also consistent with studies that have suggested a poleward shift of the main storm tracks.

Memristor-based neural networks: Synaptic versus neuronal stochasticity

NASA Astrophysics Data System (ADS)

Naous, Rawan; AlShedivat, Maruan; Neftci, Emre; Cauwenberghs, Gert; Salama, Khaled Nabil

2016-11-01

In neuromorphic circuits, stochasticity in the cortex can be mapped into the synaptic or neuronal components. The hardware emulation of these stochastic neural networks are currently being extensively studied using resistive memories or memristors. The ionic process involved in the underlying switching behavior of the memristive elements is considered as the main source of stochasticity of its operation. Building on its inherent variability, the memristor is incorporated into abstract models of stochastic neurons and synapses. Two approaches of stochastic neural networks are investigated. Aside from the size and area perspective, the impact on the system performance, in terms of accuracy, recognition rates, and learning, among these two approaches and where the memristor would fall into place are the main comparison points to be considered.

Dynamic modeling and adaptive vibration suppression of a high-speed macro-micro manipulator

NASA Astrophysics Data System (ADS)

Yang, Yi-ling; Wei, Yan-ding; Lou, Jun-qiang; Fu, Lei; Fang, Sheng; Chen, Te-huan

2018-05-01

This paper presents a dynamic modeling and microscopic vibration suppression for a flexible macro-micro manipulator dedicated to high-speed operation. The manipulator system mainly consists of a macro motion stage and a flexible micromanipulator bonded with one macro-fiber-composite actuator. Based on Hamilton's principle and the Bouc-Wen hysteresis equation, the nonlinear dynamic model is obtained. Then, a hybrid control scheme is proposed to simultaneously suppress the elastic vibration during and after the motor motion. In particular, the hybrid control strategy is composed of a trajectory planning approach and an adaptive variable structure control. Moreover, two optimization indices regarding the comprehensive torques and synthesized vibrations are designed, and the optimal trajectories are acquired using a genetic algorithm. Furthermore, a nonlinear fuzzy regulator is used to adjust the switching gain in the variable structure control. Thus, a fuzzy variable structure control with nonlinear adaptive control law is achieved. A series of experiments are performed to verify the effectiveness and feasibility of the established system model and hybrid control strategy. The excited vibration during the motor motion and the residual vibration after the motor motion are decreased. Meanwhile, the settling time is shortened. Both the manipulation stability and operation efficiency of the manipulator are improved by the proposed hybrid strategy.

Low Computational Signal Acquisition for GNSS Receivers Using a Resampling Strategy and Variable Circular Correlation Time

PubMed Central

Zhang, Yeqing; Wang, Meiling; Li, Yafeng

2018-01-01

For the objective of essentially decreasing computational complexity and time consumption of signal acquisition, this paper explores a resampling strategy and variable circular correlation time strategy specific to broadband multi-frequency GNSS receivers. In broadband GNSS receivers, the resampling strategy is established to work on conventional acquisition algorithms by resampling the main lobe of received broadband signals with a much lower frequency. Variable circular correlation time is designed to adapt to different signal strength conditions and thereby increase the operation flexibility of GNSS signal acquisition. The acquisition threshold is defined as the ratio of the highest and second highest correlation results in the search space of carrier frequency and code phase. Moreover, computational complexity of signal acquisition is formulated by amounts of multiplication and summation operations in the acquisition process. Comparative experiments and performance analysis are conducted on four sets of real GPS L2C signals with different sampling frequencies. The results indicate that the resampling strategy can effectively decrease computation and time cost by nearly 90–94% with just slight loss of acquisition sensitivity. With circular correlation time varying from 10 ms to 20 ms, the time cost of signal acquisition has increased by about 2.7–5.6% per millisecond, with most satellites acquired successfully. PMID:29495301

Low Computational Signal Acquisition for GNSS Receivers Using a Resampling Strategy and Variable Circular Correlation Time.

PubMed

Zhang, Yeqing; Wang, Meiling; Li, Yafeng

2018-02-24

For the objective of essentially decreasing computational complexity and time consumption of signal acquisition, this paper explores a resampling strategy and variable circular correlation time strategy specific to broadband multi-frequency GNSS receivers. In broadband GNSS receivers, the resampling strategy is established to work on conventional acquisition algorithms by resampling the main lobe of received broadband signals with a much lower frequency. Variable circular correlation time is designed to adapt to different signal strength conditions and thereby increase the operation flexibility of GNSS signal acquisition. The acquisition threshold is defined as the ratio of the highest and second highest correlation results in the search space of carrier frequency and code phase. Moreover, computational complexity of signal acquisition is formulated by amounts of multiplication and summation operations in the acquisition process. Comparative experiments and performance analysis are conducted on four sets of real GPS L2C signals with different sampling frequencies. The results indicate that the resampling strategy can effectively decrease computation and time cost by nearly 90-94% with just slight loss of acquisition sensitivity. With circular correlation time varying from 10 ms to 20 ms, the time cost of signal acquisition has increased by about 2.7-5.6% per millisecond, with most satellites acquired successfully.

Miniature Variable Pressure Scanning Electron Microscope for In-Situ Imaging and Chemical Analysis

NASA Technical Reports Server (NTRS)

Gaskin, Jessica A.; Jerman, Gregory; Gregory, Don; Sampson, Allen R.

2012-01-01

NASA Marshall Space Flight Center (MSFC) is leading an effort to develop a Miniaturized Variable Pressure Scanning Electron Microscope (MVP-SEM) for in-situ imaging and chemical analysis of uncoated samples. This instrument development will be geared towards operation on Mars and builds on a previous MSFC design of a mini-SEM for the moon (funded through the NASA Planetary Instrument Definition and Development Program). Because Mars has a dramatically different environment than the moon, modifications to the MSFC lunar mini-SEM are necessary. Mainly, the higher atmospheric pressure calls for the use of an electron gun that can operate at High Vacuum, rather than Ultra-High Vacuum. The presence of a CO2-rich atmosphere also allows for the incorporation of a variable pressure system that enables the in-situ analysis of nonconductive geological specimens. Preliminary testing of Mars meteorites in a commercial Environmental SEM(Tradmark) (FEI) confirms the usefulness of lowcurrent/low-accelerating voltage imaging and highlights the advantages of using the Mars atmosphere for environmental imaging. The unique capabilities of the MVP-SEM make it an ideal tool for pursuing key scientific goals of NASA's Flagship Mission Max-C; to perform in-situ science and collect and cache samples in preparation for sample return from Mars.

Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata

NASA Astrophysics Data System (ADS)

Roy, Anindya; Bhole, R. B.; Nandy, Partha P.; Yadav, R. C.; Pal, Sarbajit; Roy, Amitava

2015-03-01

The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A set of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system.

Using Central Composite Experimental Design to Optimize the Degradation of Tylosin from Aqueous Solution by Photo-Fenton Reaction

PubMed Central

Sarrai, Abd Elaziz; Hanini, Salah; Merzouk, Nachida Kasbadji; Tassalit, Djilali; Szabó, Tibor; Hernádi, Klára; Nagy, László

2016-01-01

The feasibility of the application of the Photo-Fenton process in the treatment of aqueous solution contaminated by Tylosin antibiotic was evaluated. The Response Surface Methodology (RSM) based on Central Composite Design (CCD) was used to evaluate and optimize the effect of hydrogen peroxide, ferrous ion concentration and initial pH as independent variables on the total organic carbon (TOC) removal as the response function. The interaction effects and optimal parameters were obtained by using MODDE software. The significance of the independent variables and their interactions was tested by means of analysis of variance (ANOVA) with a 95% confidence level. Results show that the concentration of the ferrous ion and pH were the main parameters affecting TOC removal, while peroxide concentration had a slight effect on the reaction. The optimum operating conditions to achieve maximum TOC removal were determined. The model prediction for maximum TOC removal was compared to the experimental result at optimal operating conditions. A good agreement between the model prediction and experimental results confirms the soundness of the developed model. PMID:28773551

Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata.

PubMed

Roy, Anindya; Bhole, R B; Nandy, Partha P; Yadav, R C; Pal, Sarbajit; Roy, Amitava

2015-03-01

The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A set of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system.

Mathematical modeling as a tool to investigate the design and operation of the zymotis packed-bed bioreactor for solid-state fermentation.

PubMed

Mitchell, D A; von Meien, O F

2000-04-20

Zymotis bioreactors for solid-state fermentation (SSF) are packed-bed bioreactors with internal cooling plates. This design has potential to overcome the problem of heat removal, which is one of the main challenges in SSF. In ordinary packed-bed bioreactors, which lack internal plates, large axial temperature gradients arise, leading to poor microbial growth in the end of the bed near the air outlet. The Zymotis design is suitable for SSF processes in which the substrate bed must be maintained static, but little is known about how to design and operate Zymotis bioreactors. We use a two-dimensional heat transfer model, describing the growth of Aspergillus niger on a starchy substrate, to provide guidelines for the optimum design and operation of Zymotis bioreactors. As for ordinary packed-beds, the superficial velocity of the process air is a key variable. However, the Zymotis design introduces other important variables, namely, the spacing between the internal cooling plates and the temperature of the cooling water. High productivities can be achieved at large scale, but only if small spacings between the cooling plates are used, and if the cooling water temperature is varied during the fermentation in response to bed temperatures. Copyright 2000 John Wiley & Sons, Inc.

Hybrid intelligent monironing systems for thermal power plant trips

NASA Astrophysics Data System (ADS)

Barsoum, Nader; Ismail, Firas Basim

2012-11-01

Steam boiler is one of the main equipment in thermal power plants. If the steam boiler trips it may lead to entire shutdown of the plant, which is economically burdensome. Early boiler trips monitoring is crucial to maintain normal and safe operational conditions. In the present work two artificial intelligent monitoring systems specialized in boiler trips have been proposed and coded within the MATLAB environment. The training and validation of the two systems has been performed using real operational data captured from the plant control system of selected power plant. An integrated plant data preparation framework for seven boiler trips with related operational variables has been proposed for IMSs data analysis. The first IMS represents the use of pure Artificial Neural Network system for boiler trip detection. All seven boiler trips under consideration have been detected by IMSs before or at the same time of the plant control system. The second IMS represents the use of Genetic Algorithms and Artificial Neural Networks as a hybrid intelligent system. A slightly lower root mean square error was observed in the second system which reveals that the hybrid intelligent system performed better than the pure neural network system. Also, the optimal selection of the most influencing variables performed successfully by the hybrid intelligent system.

The Regularities of Fatigue Crack Growth in Airframes Elements at Real Operation Conditions

NASA Astrophysics Data System (ADS)

Pavelko, Igors; Pavelko, Vitalijs

The results of analytical and experimental researches concerning predicting of fatigue crack growth in the operating conditions are presented. First of all the main factors causing a fatigue damage initiation and growth are analyzed and divided to two groups. Common conditions of fatigue damage precise predicting are established. The problem of fatigue crack growth at the stresses of variable amplitude was analyzed and an approach of description of this process is performed. Two examples present the efficiency of this approach. Theory of fatigue crack growth indication and the crack growth indicator (CGI) are developed. There is planned and executed a flight experiment using CGI located on two aircraft An-24 and An-26. Results of crack growth in CGI at operational load allowed to evaluate the parameters of generalized Paris-Erdogan law and statistical properties of crack increment per flight.

Control Design for an Advanced Geared Turbofan Engine

NASA Technical Reports Server (NTRS)

Chapman, Jeffryes W.; Litt, Jonathan S.

2017-01-01

This paper describes the design process for the control system of an advanced geared turbofan engine. This process is applied to a simulation that is representative of a 30,000 pound-force thrust class concept engine with two main spools, ultra-high bypass ratio, and a variable area fan nozzle. Control system requirements constrain the non-linear engine model as it operates throughout its flight envelope of sea level to 40,000 feet and from 0 to 0.8 Mach. The purpose of this paper is to review the engine control design process for an advanced turbofan engine configuration. The control architecture selected for this project was developed from literature and reflects a configuration that utilizes a proportional integral controller with sets of limiters that enable the engine to operate safely throughout its flight envelope. Simulation results show the overall system meets performance requirements without exceeding operational limits.

Short-term Operation of Multi-purpose Reservoir using Model Predictive Control

NASA Astrophysics Data System (ADS)

Uysal, Gokcen; Schwanenberg, Dirk; Alvarado Montero, Rodolfo; Sensoy, Aynur; Arda Sorman, Ali

2017-04-01

Operation of water structures especially with conflicting water supply and flood mitigation objectives is under more stress attributed to growing water demand and changing hydro-climatic conditions. Model Predictive Control (MPC) based optimal control solutions has been successfully applied to different water resources applications. In this study, Feedback Control (FBC) and MPC get combined and an improved joint optimization-simulation operating scheme is proposed. Water supply and flood control objectives are fulfilled by incorporating the long term water supply objectives into a time-dependent variable guide curve policy whereas the extreme floods are attenuated by means of short-term optimization based on MPC. A final experiment is carried out to assess the lead time performance and reliability of forecasts in a hindcasting experiment with imperfect, perturbed forecasts. The framework is tested in Yuvacık Dam reservoir where the main water supply reservoir of Kocaeli City in the northwestern part of Turkey (the Marmara region) and it requires a challenging gate operation due to restricted downstream flow conditions.

VR/LE engine with a variable R/L during a single cycle

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rychter, T.J.; Teodorczyk, A.

1985-01-01

A new concept of an engine, called a Variable R/L Engine (VR/LE) is presented. The main feature of the engine is the continuous change of the crank-radius to connecting-rod-length ratio (R/L) during the single engine cycle. The variations of the phase angle result in changes of all the engine stroke lengths and also-they are causing the changes of the thermodynamic cycle of the engine. Therefore the phase angle variations make it possible to regulate continuously the compression ratio and the displacement volume of the engine within the range which depends on the engine mechanism geometry. The presented concept can bemore » applied to all the types of the IC piston engines, independently of their size and operation principle.« less

14 CFR 119.47 - Maintaining a principal base of operations, main operations base, and main maintenance base...

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Maintaining a principal base of operations, main operations base, and main maintenance base; change of address. 119.47 Section 119.47 Aeronautics... Under Part 121 or Part 135 of This Chapter § 119.47 Maintaining a principal base of operations, main...

14 CFR 119.47 - Maintaining a principal base of operations, main operations base, and main maintenance base...

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Maintaining a principal base of operations, main operations base, and main maintenance base; change of address. 119.47 Section 119.47 Aeronautics... Under Part 121 or Part 135 of This Chapter § 119.47 Maintaining a principal base of operations, main...

14 CFR 119.47 - Maintaining a principal base of operations, main operations base, and main maintenance base...

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Maintaining a principal base of operations, main operations base, and main maintenance base; change of address. 119.47 Section 119.47 Aeronautics... Under Part 121 or Part 135 of This Chapter § 119.47 Maintaining a principal base of operations, main...

14 CFR 119.47 - Maintaining a principal base of operations, main operations base, and main maintenance base...

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Maintaining a principal base of operations, main operations base, and main maintenance base; change of address. 119.47 Section 119.47 Aeronautics... Under Part 121 or Part 135 of This Chapter § 119.47 Maintaining a principal base of operations, main...

Helicopter main-rotor speed effects on far-field acoustic levels

NASA Technical Reports Server (NTRS)

Mueller, Arnold W.; Childress, Otis S.; Hardesty, Mark

1987-01-01

The design of a helicopter is based on an understanding of many parameters and their interactions. For example, in the design stage of a helicopter, the weight, engine, and rotor speed must be considered along with the rotor geometry when considering helicopter operations. However, the relationship between the noise radiated from the helicopter and these parameters is not well understood, with only limited model and full-scale test data to study. In general, these data have shown that reduced rotor speeds result in reduced far-field noise levels. This paper reviews the status of a recent helicopter noise research project designed to provide experimental flight data to be used to better understand helicopter rotor-speed effects on far-field acoustic levels. Preliminary results are presented relative to tests conducted with a McDonnell Douglas model 500E helicopter operating with the rotor speed as the control variable over the range of 103% of the main-rotor speed (NR) to 75% NR, and with the forward speed maintained at a constant value of 80 knots.

Symmetry analysis of the high-order equations for the description of the Fermi - Pasta - Ulam problem

NASA Astrophysics Data System (ADS)

Kudryashov, N. A.; Volkov, A. K.

2017-01-01

Recently some new nonlinear equations for the description of the Fermi - Pasta - Ulam problem have been derived. The main aim of this work is to use the symmetry test to investigate these equations. We consider equations for the description of the α and α + β Fermi - Pasta - Ulam model. We find the infinitesimal operators and Lie groups, admitted by the equations. Using the groups we find the self-similar variables as well as the reductions to the ordinary differential equations. Some exact solutions are also constructed.

Orbital Express mission operations planning and resource management using ASPEN

NASA Astrophysics Data System (ADS)

Chouinard, Caroline; Knight, Russell; Jones, Grailing; Tran, Daniel

2008-04-01

As satellite equipment and mission operations become more costly, the drive to keep working equipment running with less labor-power rises. Demonstrating the feasibility of autonomous satellite servicing was the main goal behind the Orbital Express (OE) mission. Like a tow-truck delivering gas to a car on the road, the "servicing" satellite of OE had to find the "client" from several kilometers away, connect directly to the client, and transfer fluid (or a battery) autonomously, while on earth-orbit. The mission met 100% of its success criteria, and proved that autonomous satellite servicing is now a reality for space operations. Planning the satellite mission operations for OE required the ability to create a plan which could be executed autonomously over variable conditions. As the constraints for execution could change weekly, daily, and even hourly, the tools used create the mission execution plans needed to be flexible and adaptable to many different kinds of changes. At the same time, the hard constraints of the plans needed to be maintained and satisfied. The Automated Scheduling and Planning Environment (ASPEN) tool, developed at the Jet Propulsion Laboratory, was used to create the schedule of events in each daily plan for the two satellites of the OE mission. This paper presents an introduction to the ASPEN tool, an overview of the constraints of the OE domain, the variable conditions that were presented within the mission, and the solution to operations that ASPEN provided. ASPEN has been used in several other domains, including research rovers, Deep Space Network scheduling research, and in flight operations for the NASA's Earth Observing One mission's EO1 satellite. Related work is discussed, as are the future of ASPEN and the future of autonomous satellite servicing.

An examination of loads and responses of a wind turbine undergoing variable-speed operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, A.D.; Buhl, M.L. Jr.; Bir, G.S.

1996-11-01

The National Renewable Energy Laboratory has recently developed the ability to predict turbine loads and responses for machines undergoing variable-speed operation. The wind industry has debated the potential benefits of operating wind turbine sat variable speeds for some time. Turbine system dynamic responses (structural response, resonance, and component interactions) are an important consideration for variable-speed operation of wind turbines. The authors have implemented simple, variable-speed control algorithms for both the FAST and ADAMS dynamics codes. The control algorithm is a simple one, allowing the turbine to track the optimum power coefficient (C{sub p}). The objective of this paper is tomore » show turbine loads and responses for a particular two-bladed, teetering-hub, downwind turbine undergoing variable-speed operation. The authors examined the response of the machine to various turbulent wind inflow conditions. In addition, they compare the structural responses under fixed-speed and variable-speed operation. For this paper, they restrict their comparisons to those wind-speed ranges for which limiting power by some additional control strategy (blade pitch or aileron control, for example) is not necessary. The objective here is to develop a basic understanding of the differences in loads and responses between the fixed-speed and variable-speed operation of this wind turbine configuration.« less

An extended multivariate framework for drought monitoring in Mexico

NASA Astrophysics Data System (ADS)

Real-Rangel, Roberto; Pedrozo-Acuña, Adrián; Breña-Naranjo, Agustín; Alcocer-Yamanaka, Víctor

2017-04-01

Around the world, monitoring natural hazards, such as droughts, represents a critical task in risk assessment and management plans. A reliable drought monitoring system allows to identify regions affected by these phenomena so that early response measures can be implemented. In Mexico, this activity is performed using Mexico's Drought Monitor, which is based on a similar methodology as the United States Drought Monitor and the North American Drought Monitor. The main feature of these monitoring systems is the combination of ground-based and remote sensing observations that is ultimately validated by local experts. However, in Mexico in situ records of variables such as precipitation and streamflow are often scarce, or even null, in many regions of the country. Another issue that adds uncertainty in drought monitoring is the arbitrary weight given to each analyzed variable. This study aims at providing an operational framework for drought monitoring in Mexico, based on univariate and multivariate nonparametric standardized indexes proposed in recent studies. Furthermore, the framework has been extended by taking into account the Enhanced Vegetation Index (EVI) for the drought severity assessment. The analyzed variables used for computing the drought indexes are mainly derived from remote sensing (MODIS) and land surface models datasets (NASA MERRA-2). A qualitative evaluation of the results shows that the indexes used are capable of adequately describes the intensity and spatial distribution of past drought documented events.

WSES Jerusalem guidelines for diagnosis and treatment of acute appendicitis.

PubMed

Di Saverio, Salomone; Birindelli, Arianna; Kelly, Micheal D; Catena, Fausto; Weber, Dieter G; Sartelli, Massimo; Sugrue, Michael; De Moya, Mark; Gomes, Carlos Augusto; Bhangu, Aneel; Agresta, Ferdinando; Moore, Ernest E; Soreide, Kjetil; Griffiths, Ewen; De Castro, Steve; Kashuk, Jeffry; Kluger, Yoram; Leppaniemi, Ari; Ansaloni, Luca; Andersson, Manne; Coccolini, Federico; Coimbra, Raul; Gurusamy, Kurinchi S; Campanile, Fabio Cesare; Biffl, Walter; Chiara, Osvaldo; Moore, Fred; Peitzman, Andrew B; Fraga, Gustavo P; Costa, David; Maier, Ronald V; Rizoli, Sandro; Balogh, Zsolt J; Bendinelli, Cino; Cirocchi, Roberto; Tonini, Valeria; Piccinini, Alice; Tugnoli, Gregorio; Jovine, Elio; Persiani, Roberto; Biondi, Antonio; Scalea, Thomas; Stahel, Philip; Ivatury, Rao; Velmahos, George; Andersson, Roland

2016-01-01

Acute appendicitis (AA) is among the most common cause of acute abdominal pain. Diagnosis of AA is challenging; a variable combination of clinical signs and symptoms has been used together with laboratory findings in several scoring systems proposed for suggesting the probability of AA and the possible subsequent management pathway. The role of imaging in the diagnosis of AA is still debated, with variable use of US, CT and MRI in different settings worldwide. Up to date, comprehensive clinical guidelines for diagnosis and management of AA have never been issued. In July 2015, during the 3rd World Congress of the WSES, held in Jerusalem (Israel), a panel of experts including an Organizational Committee and Scientific Committee and Scientific Secretariat, participated to a Consensus Conference where eight panelists presented a number of statements developed for each of the eight main questions about diagnosis and management of AA. The statements were then voted, eventually modified and finally approved by the participants to The Consensus Conference and lately by the board of co-authors. The current paper is reporting the definitive Guidelines Statements on each of the following topics: 1) Diagnostic efficiency of clinical scoring systems, 2) Role of Imaging, 3) Non-operative treatment for uncomplicated appendicitis, 4) Timing of appendectomy and in-hospital delay, 5) Surgical treatment 6) Scoring systems for intra-operative grading of appendicitis and their clinical usefulness 7) Non-surgical treatment for complicated appendicitis: abscess or phlegmon 8) Pre-operative and post-operative antibiotics.

Comparison of environmental forcings affecting suspended sediments variability in two macrotidal, highly-turbid estuaries

NASA Astrophysics Data System (ADS)

Jalón-Rojas, Isabel; Schmidt, Sabine; Sottolichio, Aldo

2017-11-01

The relative contribution of environmental forcing frequencies on turbidity variability is, for the first time, quantified at seasonal and multiannual time scales in tidal estuarine systems. With a decade of high-frequency, multi-site turbidity monitoring, the two nearby, macrotidal and highly-turbid Gironde and Loire estuaries (west France) are excellent natural laboratories for this purpose. Singular Spectrum Analyses, combined with Lomb-Scargle periodograms and Wavelet Transforms, were applied to the continuous multiannual turbidity time series. Frequencies of the main environmental factors affecting turbidity were identified: hydrological regime (high versus low river discharges), river flow variability, tidal range, tidal cycles, and turbulence. Their relative influences show similar patterns in both estuaries and depend on the estuarine region (lower or upper estuary) and the time scale (multiannual or seasonal). On the multiannual time scale, the relative contribution of tidal frequencies (tidal cycles and range) to turbidity variability decreases up-estuary from 68% to 47%, while the influence of river flow frequencies increases from 3% to 42%. On the seasonal time scale, the relative influence of forcings frequencies remains almost constant in the lower estuary, dominated by tidal frequencies (60% and 30% for tidal cycles and tidal range, respectively); in the upper reaches, it is variable depending on hydrological regime, even if tidal frequencies are responsible for up 50% of turbidity variance. These quantifications show the potential of combined spectral analyses to compare the behavior of suspended sediment in tidal estuaries throughout the world and to evaluate long-term changes in environmental forcings, especially in a context of global change. The relevance of this approach to compare nearby and overseas systems and to support management strategies is discussed (e.g., selection of effective operation frequencies/regions, prediction of the most affected regions by the implementation of operational management plans).

Comparison between variable and constant rotor speed operation on WINDMEL-II

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sasamoto, Akira; Matsumiya, Hikaru; Kawamura, Shunji

1996-10-01

On a wind turbine control system for rotor revolution speed, it is believed that variable speed operation has the advantages over constant speed from a view point of both aerodynamics and mechanics. However, there is no experimental study which shows the differences. In this report, the authors intend to clarify the differences about shaft torque by using experimental data, from a new wind turbine system which has both variable and constant operation. The result in observation of the experimental data shows that variable speed operational shaft torque is lower than constant speed operational one.

Variability as a Subject Matter in a Science of Behavior: Reply to Commentaries

ERIC Educational Resources Information Center

Barba, Lourenco de Souza

2012-01-01

In his article, the author claimed that studies of operant variability that use a lag-"n" or threshold procedure and measure the obtained variability through the change in U value fail to provide direct evidence that variability is an operant dimension of behavior. To do so, he adopted Catania's (1973) concept of the operant, which takes the…

Uncertainties in discharge projections in consequence of climate change

NASA Astrophysics Data System (ADS)

Liebert, J.; Düthmann, D.; Berg, P.; Feldmann, H.; Ihringer, J.; Kunstmann, H.; Merz, B.; Ott, I.; Schädler, G.; Wagner, S.

2012-04-01

The fourth assessment report of the IPCC summarizes possible effects of the global climate change. For Europe an increasing variability of temperature and precipitation is expected. While the increasing temperature is projected almost uniformly for Europe, for precipitation the models indicate partly heterogeneous tendencies. In order to maintain current safety-standards in the infrastructure of our various water management systems, the possible future floods discharges are very often a central question. In the planning and operation of water infrastructure systems uncertainties considerations have an important function. In times of climate change the analyses of measured historical gauge data (normally 30 - 80 years) are not sufficient enough, because even significant trends are only valid in the analyzed time period and extrapolations are exceedingly difficult. Therefore combined climate and hydrological modeling for scenario based projections become more and more popular. Regarding that adaptation measures in water infrastructure are in general very time-consuming and cost intensive qualified questions to the variability and uncertainty of model based results are important as well. The CEDIM-Project "Flood hazards in a changing climate" is focusing on both: future changes in flood discharge and assess the uncertainties that are involved in such model based future predictions. In detail the study bases on an ensemble of hydrological model (HM) simulations in 3 representative small to medium sized German river catchments (Ammer, Mulde and Ruhr). The meteorological Input bases on 2 high resolution (7 km) regional climate models (RCM) driven by 2 global climate models (GCM) for the near future (2021 - 2050) following the A1B emission scenario (SRES). Two of the catchments (Ruhr and Mulde) have sub-mountainous and one (Ammer) has alpine character. Besides analyzing the future changes in discharge in the catchments, the describing and potential quantification of the variability of the results, based on the different driving data, regionalization methods, spatial resolutions and model types, is one main goal of the study and should stay in the focus of the poster. The general result is a large variability in the discharge projection. The identified variabilities are in the annual regime mainly attributable to different causes in the used model chain (GCM-RCM-HM). In winter the global climate models (GCM) bring the main uncertainties in the future projection. In summer the main variability refers to the meteorological downscaling to the regional scale (RCM) in combination with the hydrological modeling (HM). But with an appropriate ensemble statistic are despite the large variabilities mean future tendencies detectable. The Ruhr catchment shows tendencies to future higher flood discharges and in the Ammer and Mulde catchments are no significant changes expected.

Computational Assessment of the Aerodynamic Performance of a Variable-Speed Power Turbine for Large Civil Tilt-Rotor Application

NASA Technical Reports Server (NTRS)

Welch, Gerard E.

2011-01-01

The main rotors of the NASA Large Civil Tilt-Rotor notional vehicle operate over a wide speed-range, from 100% at take-off to 54% at cruise. The variable-speed power turbine offers one approach by which to effect this speed variation. Key aero-challenges include high work factors at cruise and wide (40 to 60 deg.) incidence variations in blade and vane rows over the speed range. The turbine design approach must optimize cruise efficiency and minimize off-design penalties at take-off. The accuracy of the off-design incidence loss model is therefore critical to the turbine design. In this effort, 3-D computational analyses are used to assess the variation of turbine efficiency with speed change. The conceptual design of a 4-stage variable-speed power turbine for the Large Civil Tilt-Rotor application is first established at the meanline level. The design of 2-D airfoil sections and resulting 3-D blade and vane rows is documented. Three-dimensional Reynolds Averaged Navier-Stokes computations are used to assess the design and off-design performance of an embedded 1.5-stage portion-Rotor 1, Stator 2, and Rotor 2-of the turbine. The 3-D computational results yield the same efficiency versus speed trends predicted by meanline analyses, supporting the design choice to execute the turbine design at the cruise operating speed.

Overview of Variable-Speed Power-Turbine Research

NASA Technical Reports Server (NTRS)

Welch, Gerard E.

2011-01-01

The vertical take-off and landing (VTOL) and high-speed cruise capability of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle is envisaged to enable increased throughput in the national airspace. A key challenge of the LCTR is the requirement to vary the main rotor speeds from 100% at take-off to near 50% at cruise as required to minimize mission fuel burn. The variable-speed power-turbine (VSPT), driving a fixed gear-ratio transmission, provides one approach for effecting this wide speed variation. The key aerodynamic and rotordynamic challenges of the VSPT were described in the FAP Conference presentation. The challenges include maintaining high turbine efficiency at high work factor, wide (60 deg.) of incidence variation in all blade rows due to the speed variation, and operation at low Reynolds numbers (with transitional flow). The PT -shaft of the VSPT must be designed for safe operation in the wide speed range required, and therefore poses challenges associated with rotordynamics. The technical challenges drive research activities underway at NASA. An overview of the NASA SRW VSPT research activities was provided. These activities included conceptual and preliminary aero and mechanical (rotordynamics) design of the VSPT for the LCTR application, experimental and computational research supporting the development of incidence tolerant blading, and steps toward component-level testing of a variable-speed power-turbine of relevance to the LCTR application.

Uroflowmetric changes, success rate and complications following Tension-free Vaginal Tape Obturator (TVT-O) operation in obese females.

PubMed

Fouad, Reham; El-Faissal, Yahia M; Hashem, Ahmed T; Gad Allah, Sherine H

2017-07-01

The goal of this study was to evaluate the outcome of Tension-free Vaginal Tape Obturator (TVT-O) operation in the treatment of urodynamic stress incontinence (USI) in obese females, with respect to uroflowmetric changes, success rate and postoperative complications. This prospective observational study included 26 patients with USI at the Obstetrics & Gynecology department-Cairo University hospital during the year 2015. The participants had body mass index (BMI)≥30. Patients underwent TVT-O operation. Follow up of the patients was performed by cough test and uroflowmetry after one week, one month, three months and six months. Postoperative complications such as groin pain, sense of incomplete emptying, need to strain to complete micturition and urinary tract infection were recorded. Comparisons between groups were done using Chi square, Phi-Cramer test for categorical variables. The mean age for the subjects was 43.58±9.01years. The mean BMI was 33.4±2.1. The success rate of TVT-O operation was 21 out of 26 patients (≈81%). Normal maximum flow rate was in 88% of patients at week one and was normal in 100% of patients at months three and six (p=0.101 & 0.101). Postoperative groin pain was the main complaint during the first week after operation and decreased significantly from week one to the 1st month postoperative (84.62% & 65.38%, P=0.041). TVT-O operation showed a high success rate in treatment of USI in obese patients without affecting the voiding function of the bladder as proven by the uroflowmetry. The main postoperative complaint was the groin pain which significantly improved after one month. Copyright © 2017 Elsevier B.V. All rights reserved.

The importance of scale-dependent ravine characteristics on breeding-site selection by the Burrowing Parrot, Cyanoliseus patagonus

PubMed Central

Rios, Rodrigo S.; Vargas-Rodriguez, Renzo; Novoa-Jerez, Jose-Enrique; Squeo, Francisco A.

2017-01-01

In birds, the environmental variables and intrinsic characteristics of the nest have important fitness consequences through its influence on the selection of nesting sites. However, the extent to which these variables interact with variables that operate at the landscape scale, and whether there is a hierarchy among the different scales that influences nest-site selection, is unknown. This interaction could be crucial in burrowing birds, which depend heavily on the availability of suitable nesting locations. One representative of this group is the burrowing parrot, Cyanoliseus patagonus that breeds on specific ravines and forms large breeding colonies. At a particular site, breeding aggregations require the concentration of adequate environmental elements for cavity nesting, which are provided by within ravine characteristics. Therefore, intrinsic ravine characteristics should be more important in determining nest site selection compared to landscape level characteristics. Here, we assess this hypothesis by comparing the importance of ravine characteristics operating at different scales on nest-site selection and their interrelation with reproductive success. We quantified 12 characteristics of 105 ravines in their reproductive habitat. For each ravine we quantified morphological variables, distance to resources and disturbance as well as nest number and egg production in order to compare selected and non-selected ravines and determine the interrelationship among variables in explaining ravine differences. In addition, the number of nests and egg production for each reproductive ravine was related to ravine characteristics to assess their relation to reproductive success. We found significant differences between non-reproductive and reproductive ravines in both intrinsic and extrinsic characteristics. The multidimensional environmental gradient of variation between ravines, however, shows that differences are mainly related to intrinsic morphological characteristics followed by extrinsic variables associated to human disturbance. Likewise, within reproductive ravines, intrinsic characteristics are more strongly related to the number of nests. The probability of producing eggs, however, was related only to distance to roads and human settlements. Patterns suggest that C. patagonus mainly selects nesting sites based on intrinsic morphological characteristics of ravines. Scale differences in the importance of ravine characteristics could be a consequence of the particular orography of the breeding habitat. The arrangement of resources is associated to the location of the gullies rather than to individual ravines, determining the spatial availability and disposition of resources and disturbances. Thus, nest selection is influenced by intrinsic characteristics that maximize the fitness of individuals. Scaling in nest-selection is discussed under an optimality approach that partitions patch selection based on foraging theory. PMID:28462019

Seasonal Variability Study of the Tropospheric Zenithal Delay in the South America using regional Numerical Weather Prediction model

NASA Astrophysics Data System (ADS)

Sapucci, L. F.; Monico, J. G.; Machado, L. T.

2007-05-01

In 2010 a new navigation and administration system of the air traffic, denominated CNS-ATM (Communication Navigation Surveillance - Air Traffic Management) should be running operationally in South America. This new system will basically employ the positioning techniques by satellites to the management and air traffic control. However, the efficiency of this new system demands the knowledge of the behavior of the atmosphere, consequently, an appropriated Zenithal Tropospheric Delay (ZTD) modeling in a regional scale. The predictions of ZTD values from Numeric Weather Prediction (NWP), denominated here dynamic modeling, is an alternative to model the atmospheric gases effects in the radio-frequency signals in real time. Brazilian Center for Weather Forecasting and Climate Studies (CPTEC) of the National Institute for Space Research (INPE), jointly with researchers from UNESP (Sao Paulo State University), has generated operationally prediction of ZTD values to South America Continent (available in the electronic address http:satelite.cptec.inpe.br/htmldocs/ztd/zenithal.htm). The available regional version is obtained using ETA model (NWP model with horizontal resolution of 20 km and 42 levels in the vertical). The application of NWP permit assess the temporal and spatial variation of ZTD values, which is an important characteristic of this techniques. The aim of the present paper is to investigate the ZTD seasonal variability over South America continent. A variability analysis of the ZTD components [hydrostatic(ZHD) and wet(ZWD)] is also presented, as such as discussion of main factors that influence this variation in this region. The hydrostatic component variation is related with atmospheric pressure oscillation, which is influenced by relief and high pressure centers that prevail over different region of the South America continent. The wet component oscillation is due to the temperature and humidity variability, which is also influenced by relief and by synoptic events like: the penetration the cold front from Antarctic pole into the continent and occurrence of humidity convergence zones. In South America there are two main convergence zones that has strong influence in the troposphere variability, the ITCZ (Inter Tropical Convergence Zone) and the SACZ (South Atlantic Convergence Zone) zones. These convergence zones are characterized by an extensive precipitation band and high nebulosity almost stationary. The physical processes associated with these convergence zones present strong impacts in the variability of ZWD values. This work aims to contribute with ZTD modeling over South America continent using NWP to identify where and when the ZTD values present lower predictability in this region, and consequently, minimizing the error in the GNSS positioning that apply this technique.

Transfer matrix spectrum for cyclic representations of the 6-vertex reflection algebra by quantum separation of variables

NASA Astrophysics Data System (ADS)

Pezelier, Baptiste

2018-02-01

In this proceeding, we recall the notion of quantum integrable systems on a lattice and then introduce the Sklyanin’s Separation of Variables method. We sum up the main results for the transfer matrix spectral problem for the cyclic representations of the trigonometric 6-vertex reflection algebra associated to the Bazanov-Stroganov Lax operator. These results apply as well to the spectral analysis of the lattice sine-Gordon model with open boundary conditions. The transfer matrix spectrum (both eigenvalues and eigenstates) is completely characterized in terms of the set of solutions to a discrete system of polynomial equations. We state an equivalent characterization as the set of solutions to a Baxter’s like T-Q functional equation, allowing us to rewrite the transfer matrix eigenstates in an algebraic Bethe ansatz form.

49 CFR 218.105 - Additional operational requirements for hand-operated main track switches.

Code of Federal Regulations, 2013 CFR

2013-10-01

...-operated main track switches. 218.105 Section 218.105 Transportation Other Regulations Relating to... PRACTICES Handling Equipment, Switches, and Fixed Derails § 218.105 Additional operational requirements for hand-operated main track switches. (a) Each railroad shall adopt and comply with an operating rule...

49 CFR 218.105 - Additional operational requirements for hand-operated main track switches.

Code of Federal Regulations, 2011 CFR

2011-10-01

...-operated main track switches. 218.105 Section 218.105 Transportation Other Regulations Relating to... PRACTICES Handling Equipment, Switches, and Fixed Derails § 218.105 Additional operational requirements for hand-operated main track switches. (a) Each railroad shall adopt and comply with an operating rule...

49 CFR 218.105 - Additional operational requirements for hand-operated main track switches.

Code of Federal Regulations, 2014 CFR

2014-10-01

...-operated main track switches. 218.105 Section 218.105 Transportation Other Regulations Relating to... PRACTICES Handling Equipment, Switches, and Fixed Derails § 218.105 Additional operational requirements for hand-operated main track switches. (a) Each railroad shall adopt and comply with an operating rule...

49 CFR 218.105 - Additional operational requirements for hand-operated main track switches.

Code of Federal Regulations, 2012 CFR

2012-10-01

...-operated main track switches. 218.105 Section 218.105 Transportation Other Regulations Relating to... PRACTICES Handling Equipment, Switches, and Fixed Derails § 218.105 Additional operational requirements for hand-operated main track switches. (a) Each railroad shall adopt and comply with an operating rule...

An anesthesia information system for monitoring and record keeping during surgical anesthesia.

PubMed

Klocke, H; Trispel, S; Rau, G; Hatzky, U; Daub, D

1986-10-01

We have developed an anesthesia information system (AIS) that supports the anesthesiologist in monitoring and recording during a surgical operation. In development of the system, emphasis was placed on providing an anesthesiologist-computer interface that can be adapted to typical situations during anesthesia and to individual user behavior. One main feature of this interface is the integration of the input and output of information. The only device for interaction between the anesthesiologist and the AIS is a touch-sensitive, high-resolution color display screen. The anesthesiologist enters information by touching virtual function keys displayed on the screen. A data window displays all data generated over time, such as automatically recorded vital signs, including blood pressure, heart rate, and rectal and esophageal temperatures, and manually entered variables, such as administered drugs, and ventilator settings. The information gathered by the AIS is presented on the cathode ray tube in several pages. A main distributor page gives an overall view of the content of every work page. A one-page record of the anesthesia is automatically plotted on a multicolor digital plotter during the operation. An example of the use of the AIS is presented from a field test of the system during which it was evaluated in the operating room without interfering with the ongoing operation. Medical staff who used the AIS imitated the anesthesiologist's recording and information search behavior but did not have responsibility for the conduct of the anesthetic.

30 CFR 57.22203 - Main fan operation (I-C mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation (I-C mines). 57.22203... Standards for Methane in Metal and Nonmetal Mines Ventilation § 57.22203 Main fan operation (I-C mines). Main fans shall be operated continuously while ore production is in progress. ...

Operator Variability in Scan Positioning is a Major Component of HR-pQCT Precision Error and is Reduced by Standardized Training

PubMed Central

Bonaretti, Serena; Vilayphiou, Nicolas; Chan, Caroline Mai; Yu, Andrew; Nishiyama, Kyle; Liu, Danmei; Boutroy, Stephanie; Ghasem-Zadeh, Ali; Boyd, Steven K.; Chapurlat, Roland; McKay, Heather; Shane, Elizabeth; Bouxsein, Mary L.; Black, Dennis M.; Majumdar, Sharmila; Orwoll, Eric S.; Lang, Thomas F.; Khosla, Sundeep; Burghardt, Andrew J.

2017-01-01

Introduction HR-pQCT is increasingly used to assess bone quality, fracture risk and anti-fracture interventions. The contribution of the operator has not been adequately accounted in measurement precision. Operators acquire a 2D projection (“scout view image”) and define the region to be scanned by positioning a “reference line” on a standard anatomical landmark. In this study, we (i) evaluated the contribution of positioning variability to in vivo measurement precision, (ii) measured intra- and inter-operator positioning variability, and (iii) tested if custom training software led to superior reproducibility in new operators compared to experienced operators. Methods To evaluate the operator in vivo measurement precision we compared precision errors calculated in 64 co-registered and non-co-registered scan-rescan images. To quantify operator variability, we developed software that simulates the positioning process of the scanner’s software. Eight experienced operators positioned reference lines on scout view images designed to test intra- and inter-operator reproducibility. Finally, we developed modules for training and evaluation of reference line positioning. We enrolled 6 new operators to participate in a common training, followed by the same reproducibility experiments performed by the experienced group. Results In vivo precision errors were up to three-fold greater (Tt.BMD and Ct.Th) when variability in scan positioning was included. Inter-operator precision errors were significantly greater than short-term intra-operator precision (p<0.001). New trained operators achieved comparable intra-operator reproducibility to experienced operators, and lower inter-operator reproducibility (p<0.001). Precision errors were significantly greater for the radius than for the tibia. Conclusion Operator reference line positioning contributes significantly to in vivo measurement precision and is significantly greater for multi-operator datasets. Inter-operator variability can be significantly reduced using a systematic training platform, now available online (http://webapps.radiology.ucsf.edu/refline/). PMID:27475931

A system dynamics approach for integrated management of the Jucar River Basin

NASA Astrophysics Data System (ADS)

Rubio-Martin, Adria; Macian-Sorribes, Hector; Pulido-Velazquez, Manuel

2017-04-01

System dynamics (SD) is a modelling approach that allows the analysis of complex systems through the mathematical definition of variables and their relationships. Based on systems thinking, SD is suitable for interdisciplinary studies of the management of complex systems. Over the past 50 years, SD tools have been applied to fields as diverse as economics, ecology, politics, sociology and resource management. Its application to the field of water resources has grown significantly over the last two decades, facilitating the enhancement of models by adding social, economic and ecological components. However, its application to the operation of complex multireservoir systems has been very limited so far. In this contribution, we have developed a SD model for the Jucar River Basin, one of the most vulnerable basins in the western Mediterranean region with regard to droughts. The system has three main reservoirs, which allows for a multiannual management of the storage that compensates the highly variable streamflow from upstream. Our SD model of the Jucar River Basin is able to capture the complexity of the water resource system. The model developed consists of five interlinked subsystems: a) Topology of the system network, including the 3 main reservoirs, water seepage and evaporation, inflows and catchments. b) Monthly operating rules of each reservoir. The rules were derived from the expert knowledge eluded from the operators of the reservoirs. c) Monthly urban, agricultural and environmental water demands. d) State index of the system and drought mitigation measures triggered depending on the state index. e) Mancha Oriental aquifer and stream-aquifer interaction with the Jucar River. The comparison between observed and simulated series showed that the model provides a good representation of the observed reservoir operation and total deficits. The interdisciplinary and open nature of the methodology allows to add new variables and dynamics to the model that are rooted on non-physical system components, including management (operating rules), political (drought mitigation measures), and social (population growth) aspects. The structure-behaviour link of SD models allows analysis of how changes in one part of the system might affect the behaviour of the system as a whole. This allows testing how the system will respond under varying sets of conditions, including climate change scenarios. ACKNOWLEDGEMENTS This study has been supported by the IMPADAPT project (CGL2013-48424-C2-1-R) with MINECO (Ministerio de Economía y Competitividad, España) and FEDER funds, the European Union's Horizon 2020 research and innovation programme under the IMPREX project (GA n. 641.811), and the Garantía Juvenil grants of the Ministerio Empleo y Seguridad Social, Spain.

30 CFR 75.311 - Main mine fan operation.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main mine fan operation. 75.311 Section 75.311... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Ventilation § 75.311 Main mine fan operation. (a) Main mine fans shall be continuously operated, except as otherwise approved in the ventilation plan, or when...

Regional Analysis of Long-term Local and Synoptic Effects on Wind Velocity and Energy Patterns in Complex Terrain

NASA Astrophysics Data System (ADS)

Belu, R.; Koracin, D. R.

2017-12-01

Investments in renewable energy are justified in both environmental and economic terms. Climate change risks call for mitigation strategies aimed to reduce pollutant emissions, while the energy supply is facing high uncertainty by the current or future global economic and political contexts. Wind energy is playing a strategic role in the efforts of any country for sustainable development and energy supply security. Wind energy is a weather and climate-dependent resource, having a natural spatio-temporal variability at time scales ranging from fraction of seconds to seasons and years, while at spatial scales is strongly affected by the topography and vegetation. Main objective of the study is to investigate spatio-temporal characteristics of the wind velocity in the Southwest U.S., that are relevant to wind energy assessment, analysis, development, operation, and grid integration, by using long-term multiple meteorological tower observations. Wind velocity data and other meteorological parameters from five towers, located near Tonopah, Nevada, operated between 2003 to 2008, and from three towers are located in Carson Valley, Nevada, operated between 2006 and 2014 were used in this study. Multi-annual wind speed data collected did not show significant increase trends with increasing elevation; the differences are mainly governed by the topographic complexity, including local atmospheric circulations. Auto- and cross-correlations show a strong coherence between the wind speed and direction with slowly decreasing amplitude of the multi-day periodicity with increasing lag periods. Besides pronounced diurnal periodicity at all locations, detrended fluctuation analysis also showed significant seasonal and annual periodicities, and long-memory persistence with similar characteristics. In spite of significant differences in mean wind speeds among the towers, due to location specifics, the relatively high auto- and cross-correlation coefficients among the towers indicate that the regional synoptic processes are dominant for wind variability.

Environmental links to interannual variability in shellfish toxicity in Cobscook Bay and eastern Maine, a strongly tidally mixed coastal region

NASA Astrophysics Data System (ADS)

Horecka, Hannah M.; Thomas, Andrew C.; Weatherbee, Ryan A.

2014-05-01

The Gulf of Maine experiences annual closures of shellfish harvesting due to the accumulation of toxins produced by dinoflagellates of the genus Alexandrium. Factors controlling the timing, location, and magnitude of these events in eastern Maine remain poorly understood. Previous work identified possible linkages between interannual variability of oceanographic variables and shellfish toxicity along the western Maine coastline but no such linkages were evident along the eastern Maine coast in the vicinity of Cobscook Bay, where strong tidal mixing tends to reduce seasonal variability in oceanographic properties. Using 21 years (1985-2005) of shellfish toxicity data, interannual variability in two metrics of annual toxicity, maximum magnitude and total annual toxicity, from stations in the Cobscook Bay region are examined for relationships to a suite of available environmental variables. Consistent with earlier work, no (or only weak) correlations were found between toxicity and oceanographic variables, even those very proximate to the stations such as local sea surface temperature. Similarly no correlations were evident between toxicity and air temperature, precipitation or relative humidity. The data suggest possible connections to local river discharge, but plausible mechanisms are not obvious. Correlations between toxicity and two variables indicative of local meteorological conditions, dew point and atmospheric pressure, both suggest a link between increased toxicity in these eastern Maine stations and weather conditions characterized by clearer skies/drier air (or less stormy/humid conditions). As no correlation of opposite sign was evident between toxicity and local precipitation, one plausible link is through light availability and its positive impact on phytoplankton production in this persistently foggy section of coast. These preliminary findings point to both the value of maintaining long-term shellfish toxicity sampling and a need for inclusion of weather variability in future modeling studies aimed at development of a more mechanistic understanding of factors controlling interannual differences in eastern Gulf of Maine shellfish toxicity.

Implementation of EPICS based vacuum control system for variable energy cyclotron centre, Kolkata

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roy, Anindya, E-mail: r-ani@vecc.gov.in; Bhole, R. B.; Nandy, Partha P.

2015-03-15

The vacuum system of the Room Temperature (K = 130) Cyclotron of Variable Energy Cyclotron Centre is comprised of vacuum systems of main machine and Beam Transport System. The vacuum control system is upgraded to a PLC based Automated system from the initial relay based Manual system. The supervisory control of the vacuum system is implemented in Experimental Physics and Industrial Control System (EPICS). An EPICS embedded ARM based vacuum gauge controller is developed to mitigate the requirement of vendor specific gauge controller for gauges and also for seamless integration of the gauge controllers with the control system. A setmore » of MS-Windows ActiveX components with embedded EPICS Channel Access interface are developed to build operator interfaces with less complex programming and to incorporate typical Windows feature, e.g., user authentication, file handling, better fonts, colors, mouse actions etc. into the operator interfaces. The control parameters, monitoring parameters, and system interlocks of the system are archived in MySQL based EPICS MySQL Archiver developed indigenously. In this paper, we describe the architecture, the implementation details, and the performance of the system.« less

Bimodal Nuclear Thermal Rocket Sizing and Trade Matrix for Lunar, Near Earth Asteroid and Mars Missions

NASA Astrophysics Data System (ADS)

McCurdy, David R.; Krivanek, Thomas M.; Roche, Joseph M.; Zinolabedini, Reza

2006-01-01

The concept of a human rated transport vehicle for various near earth missions is evaluated using a liquid hydrogen fueled Bimodal Nuclear Thermal Propulsion (BNTP) approach. In an effort to determine the preliminary sizing and optimal propulsion system configuration, as well as the key operating design points, an initial investigation into the main system level parameters was conducted. This assessment considered not only the performance variables but also the more subjective reliability, operability, and maintainability attributes. The SIZER preliminary sizing tool was used to facilitate rapid modeling of the trade studies, which included tank materials, propulsive versus an aero-capture trajectory, use of artificial gravity, reactor chamber operating pressure and temperature, fuel element scaling, engine thrust rating, engine thrust augmentation by adding oxygen to the flow in the nozzle for supersonic combustion, and the baseline turbopump configuration to address mission redundancy and safety requirements. A high level system perspective was maintained to avoid focusing solely on individual component optimization at the expense of system level performance, operability, and development cost.

Variable Order and Distributed Order Fractional Operators

NASA Technical Reports Server (NTRS)

Lorenzo, Carl F.; Hartley, Tom T.

2002-01-01

Many physical processes appear to exhibit fractional order behavior that may vary with time or space. The continuum of order in the fractional calculus allows the order of the fractional operator to be considered as a variable. This paper develops the concept of variable and distributed order fractional operators. Definitions based on the Riemann-Liouville definitions are introduced and behavior of the operators is studied. Several time domain definitions that assign different arguments to the order q in the Riemann-Liouville definition are introduced. For each of these definitions various characteristics are determined. These include: time invariance of the operator, operator initialization, physical realization, linearity, operational transforms. and memory characteristics of the defining kernels. A measure (m2) for memory retentiveness of the order history is introduced. A generalized linear argument for the order q allows the concept of "tailored" variable order fractional operators whose a, memory may be chosen for a particular application. Memory retentiveness (m2) and order dynamic behavior are investigated and applications are shown. The concept of distributed order operators where the order of the time based operator depends on an additional independent (spatial) variable is also forwarded. Several definitions and their Laplace transforms are developed, analysis methods with these operators are demonstrated, and examples shown. Finally operators of multivariable and distributed order are defined in their various applications are outlined.

Nonlinear dynamics of global atmospheric and earth system processes

NASA Technical Reports Server (NTRS)

Zhang, Taiping; Verbitsky, Mikhail; Saltzman, Barry; Mann, Michael E.; Park, Jeffrey; Lall, Upmanu

1995-01-01

During the grant period, the authors continued ongoing studies aimed at enhancing their understanding of the operation of the atmosphere as a complex nonlinear system interacting with the hydrosphere, biosphere, and cryosphere in response to external radiative forcing. Five papers were completed with support from the grant, representing contributions in three main areas of study: (1) theoretical studies of the interactive atmospheric response to changed biospheric boundary conditions measurable from satellites; (2) statistical-observational studies of global-scale temperature variability on interannual to century time scales; and (3) dynamics of long-term earth system changes associated with ice sheet surges.

Two-step digit-set-restricted modified signed-digit addition-subtraction algorithm and its optoelectronic implementation.

PubMed

Qian, F; Li, G; Ruan, H; Jing, H; Liu, L

1999-09-10

A novel, to our knowledge, two-step digit-set-restricted modified signed-digit (MSD) addition-subtraction algorithm is proposed. With the introduction of the reference digits, the operand words are mapped into an intermediate carry word with all digits restricted to the set {1, 0} and an intermediate sum word with all digits restricted to the set {0, 1}, which can be summed to form the final result without carry generation. The operation can be performed in parallel by use of binary logic. An optical system that utilizes an electron-trapping device is suggested for accomplishing the required binary logic operations. By programming of the illumination of data arrays, any complex logic operations of multiple variables can be realized without additional temporal latency of the intermediate results. This technique has a high space-bandwidth product and signal-to-noise ratio. The main structure can be stacked to construct a compact optoelectronic MSD adder-subtracter.

Chemometric study on the electrochemical incineration of diethylenetriaminepentaacetic acid using boron-doped diamond anode.

PubMed

Xian, Jiahui; Liu, Min; Chen, Wei; Zhang, Chunyong; Fu, Degang

2018-05-01

The electrochemical incineration of diethylenetriaminepentaacetic acid (DTPA) with boron-doped diamond (BDD) anode had been initially performed under galvanostatic conditions. The main and interaction effects of four operating parameters (flow rate, applied current density, sulfate concentration and initial DTPA concentration) on mineralization performance were investigated. Under similar experimental conditions, Doehlert matrix (DM) and central composite rotatable design (CCRD) were used as statistical multivariate methods in the optimization of the anodic oxidation processes. A comparison between DM model and CCRD model revealed that the former was more accurate, possibly due to its higher operating level numbers employed (7 levels for two variables). Despite this, these two models resulted in quite similar optimum operating conditions. The maximum TOC removal percentages at 180 min were 76.2% and 73.8% for case of DM and CCRD, respectively. In addition, with the aid of quantum chemistry calculation and LC/MS analysis, a plausible degradation sequence of DTPA on BDD anode was also proposed. Copyright © 2018 Elsevier Ltd. All rights reserved.

Modelling Concentrating Solar Power with Thermal Energy Storage for Integration Studies (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hummon, M.; Jorgenson, J.; Denholm, P.

2013-10-01

Concentrating solar power with thermal energy storage (CSP-TES) can provide multiple benefits to the grid, including low marginal cost energy and the ability to levelize load, provide operating reserves, and provide firm capacity. It is challenging to properly value the integration of CSP because of the complicated nature of this technology. Unlike completely dispatchable fossil sources, CSP is a limited energy resource, depending on the hourly and daily supply of solar energy. To optimize the use of this limited energy, CSP-TES must be implemented in a production cost model with multiple decision variables for the operation of the CSP-TES plant.more » We develop and implement a CSP-TES plant in a production cost model that accurately characterizes the three main components of the plant: solar field, storage tank, and power block. We show the effect of various modelling simplifications on the value of CSP, including: scheduled versus optimized dispatch from the storage tank and energy-only operation versus co-optimization with ancillary services.« less

Modelling Concentrating Solar Power with Thermal Energy Storage for Integration Studies: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hummon, M.; Denholm, P.; Jorgenson, J.

2013-10-01

Concentrating solar power with thermal energy storage (CSP-TES) can provide multiple benefits to the grid, including low marginal cost energy and the ability to levelize load, provide operating reserves, and provide firm capacity. It is challenging to properly value the integration of CSP because of the complicated nature of this technology. Unlike completely dispatchable fossil sources, CSP is a limited energy resource, depending on the hourly and daily supply of solar energy. To optimize the use of this limited energy, CSP-TES must be implemented in a production cost model with multiple decision variables for the operation of the CSP-TES plant.more » We develop and implement a CSP-TES plant in a production cost model that accurately characterizes the three main components of the plant: solar field, storage tank, and power block. We show the effect of various modelling simplifications on the value of CSP, including: scheduled versus optimized dispatch from the storage tank and energy-only operation versus co-optimization with ancillary services.« less

Initial Development of C.A.T.E.S.: A Simulation-Based Competency Assessment Instrument for Neonatal Nurse Practitioners.

PubMed

Cates, Leigh Ann; Bishop, Sheryl; Armentrout, Debra; Verklan, Terese; Arnold, Jennifer; Doughty, Cara

2015-01-01

Determine content validity of global statements and operational definitions and choose scenarios for Competency, Assessment, Technology, Education, and Simulation (C.A.T.E.S.), instrument in development to evaluate multidimensional competency of neonatal nurse practitioners (NNPs). Real-time Delphi (RTD) method to pursue four specific aims (SAs): (1) identify which cognitive, technical, or behavioral dimension of NNP competency accurately reflects each global statement; (2) map the global statements to the National Association of Neonatal Nurse Practitioners (NANNP) core competency domains; (3) define operational definitions for the novice to expert performance subscales; and (4) determine the essential scenarios to assess NNPs. Twenty-five NNPs and nurses with competency and simulation experience Main outcome variable: One hundred percent of global statements correct for competency dimension and all but two correct for NANNP domain. One hundred percent novice to expert operational definitions and eight scenarios chosen. Content validity determined for global statements and novice to expert definitions and essential scenarios chosen.

High-power broadband plasma maser with magnetic self-insulation

NASA Astrophysics Data System (ADS)

Litvin, Vitaliy O.; Loza, Oleg T.

2018-01-01

Presented in this paper are the results of a particle-in-cell modelling of a novel high-power microwave (HPM) source which combines the properties of two devices. The first prototype is a magnetically insulated transmission line oscillator (MILO), an HPM self-oscillator which does not need an external magnetic field and irradiates a narrow spectrum depending on its iris-loaded slow-wave structure. The second prototype is a plasma maser, a Cherenkov HPM amplifier driven by a high-current relativistic electron beam propagating in a strong external magnetic field in plasma which acts as a slow-wave structure. The radiation frequency of plasma masers mainly depends on an easily variable plasma concentration; hence, their spectrum may overlap a few octaves. The plasma-based HPM device described in this paper operates without an external magnetic field: it looks like an MILO in which the iris-loaded slow-wave structure is substituted by a hollow plasma tube. The small pulse duration of ˜1.5 ns prevents a feedback rise in the 20-cm long generation section so that the device operates as a noise amplifier. Unlike conventional ultra wideband generators, the spectrum depends not only on the pulse duration but mainly on plasma, so the operation frequency of the device ranges within 12 GHz. For irradiated frequencies above 2 GHz, the total pulse energy efficiency of 7% is demonstrated at the HPM power level ˜1 GW.

Demonstration of optically controlled data routing with the use of multiple-quantum-well bistable and electro-optical devices.

PubMed

Koppa, P; Chavel, P; Oudar, J L; Kuszelewicz, R; Schnell, J P; Pocholle, J P

1997-08-10

We present experimental results on a 1-to-64-channel free-space photonic switching demonstration system based on GaAs/GaAlAs multiple-quantum-well active device arrays. Two control schemes are demonstrated: data transparent optical self-routing usable in a packet-switching environment and direct optical control with potential signal amplification for circuit switching. The self-routing operation relies on the optical recognition of the binary destination address coded in each packet header. Address decoding is implemented with elementary optical bistable devices and modulator pixels as all-optical latches and electro-optical and gates, respectively. All 60 defect-free channels of the system could be operated one by one, but the simultaneous operation of only three channels could be achieved mainly because of the spatial nonhomogeneities of the devices. Direct-control operation is based on directly setting the bistable device reflectivity with a variable-control beam power. This working mode turned out to be much more tolerant of spatial noises: 37 channels of the system could be operated simultaneously. Further development of the system to a crossbar of N inputs and M outputs and system miniaturization are also considered.

Using Propensity Score Methods to Approximate Factorial Experimental Designs to Analyze the Relationship between Two Variables and an Outcome

ERIC Educational Resources Information Center

Dong, Nianbo

2015-01-01

Researchers have become increasingly interested in programs' main and interaction effects of two variables (A and B, e.g., two treatment variables or one treatment variable and one moderator) on outcomes. A challenge for estimating main and interaction effects is to eliminate selection bias across A-by-B groups. I introduce Rubin's causal model to…

Operational Assessment of Apollo Lunar Surface Extravehicular Activity

NASA Technical Reports Server (NTRS)

Miller, Matthew James; Claybrook, Austin; Greenlund, Suraj; Marquez, Jessica J.; Feigh, Karen M.

2017-01-01

Quantifying the operational variability of extravehicular activity (EVA) execution is critical to help design and build future support systems to enable astronauts to monitor and manage operations in deep-space, where ground support operators will no longer be able to react instantly and manage execution deviations due to the significant communication latency. This study quantifies the operational variability exhibited during Apollo 14-17 lunar surface EVA operations to better understand the challenges and natural tendencies of timeline execution and life support system performance involved in surface operations. Each EVA (11 in total) is individually summarized as well as aggregated to provide descriptive trends exhibited throughout the Apollo missions. This work extends previous EVA task analyses by calculating deviations between planned and as-performed timelines as well as examining metabolic rate and consumables usage throughout the execution of each EVA. The intent of this work is to convey the natural variability of EVA operations and to provide operational context for coping with the variability inherent to EVA execution as a means to support future concepts of operations.

3D facial landmarks: Inter-operator variability of manual annotation

PubMed Central

2014-01-01

Background Manual annotation of landmarks is a known source of variance, which exist in all fields of medical imaging, influencing the accuracy and interpretation of the results. However, the variability of human facial landmarks is only sparsely addressed in the current literature as opposed to e.g. the research fields of orthodontics and cephalometrics. We present a full facial 3D annotation procedure and a sparse set of manually annotated landmarks, in effort to reduce operator time and minimize the variance. Method Facial scans from 36 voluntary unrelated blood donors from the Danish Blood Donor Study was randomly chosen. Six operators twice manually annotated 73 anatomical and pseudo-landmarks, using a three-step scheme producing a dense point correspondence map. We analyzed both the intra- and inter-operator variability, using mixed-model ANOVA. We then compared four sparse sets of landmarks in order to construct a dense correspondence map of the 3D scans with a minimum point variance. Results The anatomical landmarks of the eye were associated with the lowest variance, particularly the center of the pupils. Whereas points of the jaw and eyebrows have the highest variation. We see marginal variability in regards to intra-operator and portraits. Using a sparse set of landmarks (n=14), that capture the whole face, the dense point mean variance was reduced from 1.92 to 0.54 mm. Conclusion The inter-operator variability was primarily associated with particular landmarks, where more leniently landmarks had the highest variability. The variables embedded in the portray and the reliability of a trained operator did only have marginal influence on the variability. Further, using 14 of the annotated landmarks we were able to reduced the variability and create a dense correspondences mesh to capture all facial features. PMID:25306436

The Impeller Exit Flow Coefficient As a Performance Map Variable for Predicting Centrifugal Compressor Off-Design Operation Applied to a Supercritical CO 2 Working Fluid

DOE PAGES

Liese, Eric; Zitney, Stephen E.

2017-06-26

A multi-stage centrifugal compressor model is presented with emphasis on analyzing use of an exit flow coefficient vs. an inlet flow coefficient performance parameter to predict off-design conditions in the critical region of a supercritical carbon dioxide (CO 2) power cycle. A description of the performance parameters is given along with their implementation in a design model (number of stages, basic sizing, etc.) and a dynamic model (for use in transient studies). A design case is shown for two compressors, a bypass compressor and a main compressor, as defined in a process simulation of a 10 megawatt (MW) supercritical COmore » 2 recompression Brayton cycle. Simulation results are presented for a simple open cycle and closed cycle process with changes to the inlet temperature of the main compressor which operates near the CO 2 critical point. Results showed some difference in results using the exit vs. inlet flow coefficient correction, however, it was not significant for the range of conditions examined. Here, this paper also serves as a reference for future works, including a full process simulation of the 10 MW recompression Brayton cycle.« less

Development of a Moisture-in-Solid-Insulation Sensor for Power Transformers

PubMed Central

García, Belén; García, Diego; Robles, Guillermo

2015-01-01

Moisture is an important variable that must be kept under control to guarantee a safe operation of power transformers. Because of the hydrophilic character of cellulose, water mainly remains in the solid insulation, while just a few parts per million are dissolved in oil. The distribution of moisture between paper and oil is not static, but varies depending on the insulation temperature, and thus, water migration processes take place continuously during transformers operation. In this work, a sensor is presented that allows the determination of the moisture content of the transformer solid insulation in the steady state and during the moisture migration processes. The main objective of the design is that the electrodes of the sensor should not obstruct the movement of water from the solid insulation to the oil, so the proposed prototype uses a metallic-mesh electrode to do the measurements. The measurement setup is based on the characterization of the insulation dielectric response by means of the frequency dielectric spectroscopy (FDS) method. The sensitivity of the proposed sensor has been tested on samples with a moisture content within 1% to 5%, demonstrating the good sensitivity and repeatability of the measurements. PMID:25658393

Development of a moisture-in-solid-insulation sensor for power transformers.

PubMed

García, Belén; García, Diego; Robles, Guillermo

2015-02-04

Moisture is an important variable that must be kept under control to guarantee a safe operation of power transformers. Because of the hydrophilic character of cellulose, water mainly remains in the solid insulation, while just a few parts per million are dissolved in oil. The distribution of moisture between paper and oil is not static, but varies depending on the insulation temperature, and thus, water migration processes take place continuously during transformers operation. In this work, a sensor is presented that allows the determination of the moisture content of the transformer solid insulation in the steady state and during the moisture migration processes. The main objective of the design is that the electrodes of the sensor should not obstruct the movement of water from the solid insulation to the oil, so the proposed prototype uses a metallic-mesh electrode to do the measurements. The measurement setup is based on the characterization of the insulation dielectric response by means of the frequency dielectric spectroscopy (FDS) method. The sensitivity of the proposed sensor has been tested on samples with a moisture content within 1% to 5%, demonstrating the good sensitivity and repeatability of the measurements.

The Impeller Exit Flow Coefficient As a Performance Map Variable for Predicting Centrifugal Compressor Off-Design Operation Applied to a Supercritical CO 2 Working Fluid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liese, Eric; Zitney, Stephen E.

A multi-stage centrifugal compressor model is presented with emphasis on analyzing use of an exit flow coefficient vs. an inlet flow coefficient performance parameter to predict off-design conditions in the critical region of a supercritical carbon dioxide (CO 2) power cycle. A description of the performance parameters is given along with their implementation in a design model (number of stages, basic sizing, etc.) and a dynamic model (for use in transient studies). A design case is shown for two compressors, a bypass compressor and a main compressor, as defined in a process simulation of a 10 megawatt (MW) supercritical COmore » 2 recompression Brayton cycle. Simulation results are presented for a simple open cycle and closed cycle process with changes to the inlet temperature of the main compressor which operates near the CO 2 critical point. Results showed some difference in results using the exit vs. inlet flow coefficient correction, however, it was not significant for the range of conditions examined. Here, this paper also serves as a reference for future works, including a full process simulation of the 10 MW recompression Brayton cycle.« less

Treatment of winery wastewater by physicochemical, biological and advanced processes: a review.

PubMed

Ioannou, L A; Li Puma, G; Fatta-Kassinos, D

2015-04-09

Winery wastewater is a major waste stream resulting from numerous cleaning operations that occur during the production stages of wine. The resulting effluent contains various organic and inorganic contaminants and its environmental impact is notable, mainly due to its high organic/inorganic load, the large volumes produced and its seasonal variability. Several processes for the treatment of winery wastewater are currently available, but the development of alternative treatment methods is necessary in order to (i) maximize the efficiency and flexibility of the treatment process to meet the discharge requirements for winery effluents, and (ii) decrease both the environmental footprint, as well as the investment/operational costs of the process. This review, presents the state-of-the-art of the processes currently applied and/or tested for the treatment of winery wastewater, which were divided into five categories: i.e., physicochemical, biological, membrane filtration and separation, advanced oxidation processes, and combined biological and advanced oxidation processes. The advantages and disadvantages, as well as the main parameters/factors affecting the efficiency of winery wastewater treatment are discussed. Both bench- and pilot/industrial-scale processes have been considered for this review. Copyright © 2014 Elsevier B.V. All rights reserved.

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP.

PubMed

Deng, Li; Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency.

Operating Comfort Prediction Model of Human-Machine Interface Layout for Cabin Based on GEP

PubMed Central

Wang, Guohua; Chen, Bo

2015-01-01

In view of the evaluation and decision-making problem of human-machine interface layout design for cabin, the operating comfort prediction model is proposed based on GEP (Gene Expression Programming), using operating comfort to evaluate layout scheme. Through joint angles to describe operating posture of upper limb, the joint angles are taken as independent variables to establish the comfort model of operating posture. Factor analysis is adopted to decrease the variable dimension; the model's input variables are reduced from 16 joint angles to 4 comfort impact factors, and the output variable is operating comfort score. The Chinese virtual human body model is built by CATIA software, which will be used to simulate and evaluate the operators' operating comfort. With 22 groups of evaluation data as training sample and validation sample, GEP algorithm is used to obtain the best fitting function between the joint angles and the operating comfort; then, operating comfort can be predicted quantitatively. The operating comfort prediction result of human-machine interface layout of driller control room shows that operating comfort prediction model based on GEP is fast and efficient, it has good prediction effect, and it can improve the design efficiency. PMID:26448740

Operant Variability: A Conceptual Analysis

ERIC Educational Resources Information Center

Barba, Lourenco de Souza

2012-01-01

Some researchers claim that variability is an operant dimension of behavior. The present paper reviews the concept of operant behavior and emphasizes that differentiation is the behavioral process that demonstrates an operant relation. Differentiation is conceived as change in the overlap between two probability distributions: the distribution of…

Visual aided pacing in respiratory maneuvers

NASA Astrophysics Data System (ADS)

Rambaudi, L. R.; Rossi, E.; Mántaras, M. C.; Perrone, M. S.; Siri, L. Nicola

2007-11-01

A visual aid to pace self-controlled respiratory cycles in humans is presented. Respiratory manoeuvres need to be accomplished in several clinic and research procedures, among others, the studies on Heart Rate Variability. Free running respiration turns to be difficult to correlate with other physiologic variables. Because of this fact, voluntary self-control is asked from the individuals under study. Currently, an acoustic metronome is used to pace respiratory frequency, its main limitation being the impossibility to induce predetermined timing in the stages within the respiratory cycle. In the present work, visual driven self-control was provided, with separate timing for the four stages of a normal respiratory cycle. This visual metronome (ViMet) was based on a microcontroller which power-ON and -OFF an eight-LED bar, in a four-stage respiratory cycle time series handset by the operator. The precise timing is also exhibited on an alphanumeric display.

Variability of the raindrop size distribution at small spatial scales

NASA Astrophysics Data System (ADS)

Berne, A.; Jaffrain, J.

2010-12-01

Because of the interactions between atmospheric turbulence and cloud microphysics, the raindrop size distribution (DSD) is strongly variable in space and time. The spatial variability of the DSD at small spatial scales (below a few km) is not well documented and not well understood, mainly because of a lack of adequate measurements at the appropriate resolutions. A network of 16 disdrometers (Parsivels) has been designed and set up over EPFL campus in Lausanne, Switzerland. This network covers a typical operational weather radar pixel of 1x1 km2. The question of the significance of the variability of the DSD at such small scales is relevant for radar remote sensing of rainfall because the DSD is often assumed to be uniform within a radar sample volume and because the Z-R relationships used to convert the measured radar reflectivity Z into rain rate R are usually derived from point measurements. Thanks to the number of disdrometers, it was possible to quantify the spatial variability of the DSD at the radar pixel scale and to show that it can be significant. In this contribution, we show that the variability of the total drop concentration, of the median volume diameter and of the rain rate are significant, taking into account the sampling uncertainty associated with disdrometer measurements. The influence of this variability on the Z-R relationship can be non-negligible. Finally, the spatial structure of the DSD is quantified using a geostatistical tool, the variogram, and indicates high spatial correlation within a radar pixel.

Concurrently adjusting interrelated control parameters to achieve optimal engine performance

DOEpatents

Jiang, Li; Lee, Donghoon; Yilmaz, Hakan; Stefanopoulou, Anna

2015-12-01

Methods and systems for real-time engine control optimization are provided. A value of an engine performance variable is determined, a value of a first operating condition and a value of a second operating condition of a vehicle engine are detected, and initial values for a first engine control parameter and a second engine control parameter are determined based on the detected first operating condition and the detected second operating condition. The initial values for the first engine control parameter and the second engine control parameter are adjusted based on the determined value of the engine performance variable to cause the engine performance variable to approach a target engine performance variable. In order to cause the engine performance variable to approach the target engine performance variable, adjusting the initial value for the first engine control parameter necessitates a corresponding adjustment of the initial value for the second engine control parameter.

Analysis of a Split-Plot Experimental Design Applied to a Low-Speed Wind Tunnel Investigation

NASA Technical Reports Server (NTRS)

Erickson, Gary E.

2013-01-01

A procedure to analyze a split-plot experimental design featuring two input factors, two levels of randomization, and two error structures in a low-speed wind tunnel investigation of a small-scale model of a fighter airplane configuration is described in this report. Standard commercially-available statistical software was used to analyze the test results obtained in a randomization-restricted environment often encountered in wind tunnel testing. The input factors were differential horizontal stabilizer incidence and the angle of attack. The response variables were the aerodynamic coefficients of lift, drag, and pitching moment. Using split-plot terminology, the whole plot, or difficult-to-change, factor was the differential horizontal stabilizer incidence, and the subplot, or easy-to-change, factor was the angle of attack. The whole plot and subplot factors were both tested at three levels. Degrees of freedom for the whole plot error were provided by replication in the form of three blocks, or replicates, which were intended to simulate three consecutive days of wind tunnel facility operation. The analysis was conducted in three stages, which yielded the estimated mean squares, multiple regression function coefficients, and corresponding tests of significance for all individual terms at the whole plot and subplot levels for the three aerodynamic response variables. The estimated regression functions included main effects and two-factor interaction for the lift coefficient, main effects, two-factor interaction, and quadratic effects for the drag coefficient, and only main effects for the pitching moment coefficient.

Comparative Study of Microstructure and Properties of Thermal Sprayed MCrAlY Bond Coatings

NASA Astrophysics Data System (ADS)

Inglima, Michael William

A series of experiments were performed in order to observe certain process-property trends in thermally sprayed MCrAlY bond coatings for thermal barrier coating (TBC) applications in gas-turbine engines. Firstly, the basis of gas-turbine operation and design is discussed with a focus on the Brayton cycle and basic thermodynamic properties with respect to both the thermal and fuel efficiency of the turbine. The high-temperature environment inside the gas-turbine engine creates an extremely corrosive medium in which the engineering components must operate with sufficient operating life times. These engineering constraints, both thermal/fuel efficiency and operating life, pose a serious problem during long operation as well as thermal cycling of a civil aerospace engine. The concept of a thermal barrier coating is introduced along with how these coatings protect the internal engineering components, mostly in the hot-section of the turbine, and increase both the efficiency as well as the operating life of the components. The method used to create TBC's is then introduced being thermal spray processing along with standard operating procedures (SOP) used during coating deposition. The main focus of the experiments was to quantify the process-property trends seen during thermal spray processing of TBC's with respect to the adhesion and thermally grown oxide (TGO) layer, as well as how sensitive these properties are to changing variables during coating deposition. The design of experiment (DOE) method was used in order to have sufficient statistical process control over the output as well as a standard method for quantifying the results. A total of three DOE's were performed using two main types of thermal spray processes being high-velocity oxygen fuel (HVOF) and atmospheric plasma spray (APS), with a total of five different types of torches which are categorized by liquid-fuel, gas-fuel, and single cathode plasma. The variables used in the proceeding experiments were mainly spray distance, air/fuel ratio, raster speed, powder feed rate, combustion pressure, current, primary and secondary gas flow, as well as three different powder chemistries. The results of the experiments showed very clear process-property trends with respect to mean bond strength of the coatings as well as TGO growth on the as-sprayed coating surface. The effect of either increasing/decreasing the melting index of the powder as well as increasing/decreasing the kinetic energy of the particles is shown with corresponding cross-sectional microstructures of the coating interfaces. The temperature and velocity of the particles were measured with spray diagnostic sensors as well as using an in-situ curvature property sensor (ICP) to monitor the stress-states of the coatings both during deposition as well as residual stresses, and how these might affect the bond strength. An SOP referred to as furnace cycling was used to quantify the TGO growth of the bond coatings by measuring the thickness via a scanning electron microscope (SEM) as well as performing energy dispersive x-ray spectroscopy (EDX) on the coatings to measure chemical changes.

Quality of blood pressure measurement in community health centres.

PubMed

Sandoya-Olivera, Edgardo; Ferreira-Umpiérrez, Augusto; Machado-González, Federico

To determine the quality of the blood pressure measurements performed during routine care in community health centres. An observational, cross-sectional study was conducted in 5 private and public health centres in Maldonado, Uruguay, in July-August 2015. The observations were made during the measurements performed by health personnel, using the requirements established by the American Heart Association. An analysis was made on 36 variables that were grouped in categories related to environment, equipment, interrogation, patient, and observer. Statistical analysis was performed using Chi 2 test or Fisher test. Statistical significance was considered to be less than 5% (p<.05). The measurements were made by a registered nurse or nurse in 71% of cases, physician in 20%, and student nurse in 9%. An aneroid sphygmomanometer was used in 89%, and mercury 11%. Satisfactory results were found in variables related to environment (93%), equipment (99%), and patient attitude (82%), and intermediate in the attitudes of the operator (64%), and poor in relation to the interrogation (18%), with the mean of correct variables per measurement being 69%. The main flaws in the procedure were the operator. The measurement of blood pressure is a manoeuvre that healthcare professionals perform thousands of times a year. If the measurement is used for the diagnosis and/or chronic management of arterial hypertension, not systematically applying the established recommendations leads to an inappropriate care of a very significant number of patients. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

Quality-by-Design approach to monitor the operation of a batch bioreactor in an industrial avian vaccine manufacturing process.

PubMed

Largoni, Martina; Facco, Pierantonio; Bernini, Donatella; Bezzo, Fabrizio; Barolo, Massimiliano

2015-10-10

Monitoring batch bioreactors is a complex task, due to the fact that several sources of variability can affect a running batch and impact on the final product quality. Additionally, the product quality itself may not be measurable on line, but requires sampling and lab analysis taking several days to be completed. In this study we show that, by using appropriate process analytical technology tools, the operation of an industrial batch bioreactor used in avian vaccine manufacturing can be effectively monitored as the batch progresses. Multivariate statistical models are built from historical databases of batches already completed, and they are used to enable the real time identification of the variability sources, to reliably predict the final product quality, and to improve process understanding, paving the way to a reduction of final product rejections, as well as to a reduction of the product cycle time. It is also shown that the product quality "builds up" mainly during the first half of a batch, suggesting on the one side that reducing the variability during this period is crucial, and on the other side that the batch length can possibly be shortened. Overall, the study demonstrates that, by using a Quality-by-Design approach centered on the appropriate use of mathematical modeling, quality can indeed be built "by design" into the final product, whereas the role of end-point product testing can progressively reduce its importance in product manufacturing. Copyright © 2015 Elsevier B.V. All rights reserved.

Design strategies for the International Space University's variable gravity research facility

NASA Technical Reports Server (NTRS)

Bailey, Sheila G.; Chiaramonte, Francis P.; Davidian, Kenneth J.

1990-01-01

A variable gravity research facility named 'Newton' was designed by 58 students from 13 countries at the International Space University's 1989 summer session at the Universite Louis Pasteur, Strasbourge, France. The project was comprehensive in scope, including a political and legal foundation for international cooperation, development and financing; technical, science and engineering issues; architectural design; plausible schedules; and operations, crew issues and maintenance. Since log-term exposure to zero gravity is known to be harmful to the human body, the main goal was to design a unique variable gravity research facility which would find a practical solution to this problem, permitting a manned mission to Mars. The facility would not duplicate other space-based facilities and would provide the flexibility for examining a number of gravity levels, including lunar and Martian gravities. Major design alternatives included a truss versus a tether based system which also involved the question of docking while spinning or despinning to dock. These design issues are described. The relative advantages or disadvantages are discussed, including comments on the necessary research and technology development required for each.

Method and apparatus for executing an asynchronous clutch-to-clutch shift in a hybrid transmission

DOEpatents

Demirovic, Besim; Gupta, Pinaki; Kaminsky, Lawrence A.; Naqvi, Ali K.; Heap, Anthony H.; Sah, Jy-Jen F.

2014-08-12

A hybrid transmission includes first and second electric machines. A method for operating the hybrid transmission in response to a command to execute a shift from an initial continuously variable mode to a target continuously variable mode includes increasing torque of an oncoming clutch associated with operating in the target continuously variable mode and correspondingly decreasing a torque of an off-going clutch associated with operating in the initial continuously variable mode. Upon deactivation of the off-going clutch, torque outputs of the first and second electric machines and the torque of the oncoming clutch are controlled to synchronize the oncoming clutch. Upon synchronization of the oncoming clutch, the torque for the oncoming clutch is increased and the transmission is operated in the target continuously variable mode.

Public hospitals in financial distress: Is privatization a strategic choice?

PubMed

Ramamonjiarivelo, Zo; Weech-Maldonado, Robert; Hearld, Larry; Menachemi, Nir; Epané, Josué Patien; O'Connor, Stephen

2015-01-01

As safety net providers, public hospitals operate in more challenging environments than private hospitals. Such environments put public hospitals at greater risk of financial distress, which may result in privatization and deterioration of the safety net. The purpose of this study was to investigate whether financial distress is associated with privatization among public hospitals. We used panel data merged from the American Hospital Association Annual Survey, Medicare Cost Reports, Area Resource File, and Local Area Unemployment Statistics. Our study population consisted of all U.S. nonfederal acute care public hospitals in 1997 tracked through 2009, resulting in 6,426 hospital-year observations. The dependent variable "privatization" was defined as conversion from public status to either private not-for-profit or private for-profit status. The main independent variable, "financial distress," was based on the Altman Z-score methodology. Control variables included market and organizational factors. Two random-effects logistic regression models with state and year fixed-effects were constructed. The independent and control variables were lagged by 1 year and 2 years for Models 1 and 2, respectively. Public hospitals in financial distress had greater odds of being privatized than public hospitals not in financial distress: (OR = 4.53, p < .001) for Model 1 and (OR = 3.05, p = .001) for Model 2. Privatization eases access to resources and may provide financial relief to government entities from the burden of continuously funding a hospital operating at a loss, which in turn may help keep the hospital open and preserve access to care for the community. Privatizing a financially distressed public hospital may be a better strategic alternative than closure. The Altman Z-score could be used as a managerial tool to monitor hospitals' financial condition and take corrective actions.

Design and Application of Drought Indexes in Highly Regulated Mediterranean Water Systems

NASA Astrophysics Data System (ADS)

Castelletti, A.; Zaniolo, M.; Giuliani, M.

2017-12-01

Costs of drought are progressively increasing due to the undergoing alteration of hydro-meteorological regimes induced by climate change. Although drought management is largely studied in the literature, most of the traditional drought indexes fail in detecting critical events in highly regulated systems, which generally rely on ad-hoc formulations and cannot be generalized to different context. In this study, we contribute a novel framework for the design of a basin-customized drought index. This index represents a surrogate of the state of the basin and is computed by combining the available information about the water available in the system to reproduce a representative target variable for the drought condition of the basin (e.g., water deficit). To select the relevant variables and combinatione thereof, we use an advanced feature extraction algorithm called Wrapper for Quasi Equally Informative Subset Selection (W-QEISS). W-QEISS relies on a multi-objective evolutionary algorithm to find Pareto-efficient subsets of variables by maximizing the wrapper accuracy, minimizing the number of selected variables, and optimizing relevance and redundancy of the subset. The accuracy objective is evaluated trough the calibration of an extreme learning machine of the water deficit for each candidate subset of variables, with the index selected from the resulting solutions identifying a suitable compromise between accuracy, cardinality, relevance, and redundancy. The approach is tested on Lake Como, Italy, a regulated lake mainly operated for irrigation supply. In the absence of an institutional drought monitoring system, we constructed the combined index using all the hydrological variables from the existing monitoring system as well as common drought indicators at multiple time aggregations. The soil moisture deficit in the root zone computed by a distributed-parameter water balance model of the agricultural districts is used as target variable. Numerical results show that our combined drought index succesfully reproduces the deficit. The index represents a valuable information for supporting appropriate drought management strategies, including the possibility of directly informing the lake operations about the drought conditions and improve the overall reliability of the irrigation supply system.

Coastal and rain-induced wind variability depicted by scatterometers

NASA Astrophysics Data System (ADS)

Portabella, M.; Lin, W.; Stoffelen, A.; Turiel, A.; Verhoef, A.; Verspeek, J.; Ballabrera, J.; Vogelzang, J.

2012-04-01

A detailed knowledge of local wind variability near the shore is very important since it strongly affects the weather and microclimate in coastal regions. Since coastal areas are densely populated and most activity at sea occurs near the shore, sea-surface wind field information is important for a number of applications. In the vicinity of land sea-breeze, wave fetch, katabatic and current effects are more likely than in the open ocean, thus enhancing air-sea interaction. Also very relevant for air-sea interaction are the rain-induced phenomena, such as downbursts and convergence. Relatively cold and dry air is effectively transported to the ocean surface and surface winds are enhanced. In general, both coastal and rain-induced wind variability are poorly resolved by Numerical Weather Prediction (NWP) models. Satellite real aperture radars (i.e., scatterometers) are known to provide accurate mesoscale (25-50 km resolution) sea surface wind field information used in a wide variety of applications. Nowadays, there are two operating scatterometers in orbit, i.e., the C-band Advanced Scatterometer (ASCAT) onboard Metop-A and the Ku-band scatterometer (OSCAT) onboard Oceansat-2. The EUMETSAT Ocean and Sea Ice Satellite Application Facility (OSI SAF) delivers several ASCAT level 2 wind products with 25 km and 12.5 km Wind Vector Cell (WVC) spacing, including a pre-operational coastal wind product as well as an OSCAT level 2 wind product with 50 km spacing in development status. Rain is known to both attenuate and scatter the microwave signal. In addition, there is a "splashing" effect. The roughness of the sea surface is increased because of splashing due to rain drops. The so-called "rain contamination" is larger for Ku-band scatterometer systems than for C-band systems. Moreover, the associated downdrafts lead to variable wind speeds and directions, further complicating the wind retrieval. The C-band ASCAT high resolution wind processing is validated under rainy conditions, using collocations with the Tropical Rainfall Measuring Mission's (TRMM) Microwave Imager (TMI) rain data, and the tropical moored buoy wind and precipitation data. It turns out that the effect of low and moderate rain appears mainly in increasing the wind variability near the surface and, unlike for Ku-band scatterometers, the rain rate itself does not appear clearly as a limiting factor in ASCAT wind quality. Moreover, the downburst patterns as observed by ASCAT are unique and have large implications for air-sea exchange. At the conference, the main progress in scatterometer wind data processing will be shown.

Development of a CCTV system for welder training and monitoring of Space Shuttle Main Engine welds

NASA Technical Reports Server (NTRS)

Gordon, S. S.; Flanigan, L. A.; Dyer, G. E.

1987-01-01

A Weld Operator's Remote Monitoring System (WORMS) for remote viewing of manual and automatic GTA welds has been developed for use in Space Shuttle Main Engine (SSME) manufacturing. This system utilizes fiberoptics to transmit images from a receiving lens to a small closed-circuit television (CCTV) camera. The camera converts the image to an electronic signal, which is sent to a videotape recorder (VTR) and a monitor. The overall intent of this system is to provide a clearer, more detailed view of welds than is available by direct observation. This system has six primary areas of application: (1) welder training; (2) viewing of joint penetration; (3) viewing visually inaccessible welds; (4) quality control and quality assurance; (5) remote joint tracking and adjustment of variables in machine welds; and (6) welding research and development. This paper describes WORMS and how it applies to each application listed.

Cheese whey management: a review.

PubMed

Prazeres, Ana R; Carvalho, Fátima; Rivas, Javier

2012-11-15

Cheese whey is simultaneously an effluent with nutritional value and a strong organic and saline content. Cheese whey management has been focused in the development of biological treatments without valorization; biological treatments with valorization; physicochemical treatments and direct land application. In the first case, aerobic digestion is reported. In the second case, six main processes are described in the literature: anaerobic digestion, lactose hydrolysis, fermentation to ethanol, hydrogen or lactic acid and direct production of electricity through microbial fuel cells. Thermal and isoelectric precipitation, thermocalcic precipitation, coagulation/flocculation, acid precipitation, electrochemical and membrane technologies have been considered as possible and attractive physicochemical processes to valorize or treat cheese whey. The direct land application is a common and longstanding practice, although some precautions are required. In this review, these different solutions are analyzed. The paper describes the main reactors used, the influence of the main operating variables, the microorganisms or reagents employed and the characterizations of the final effluent principally in terms of chemical oxygen demand. In addition, the experimental conditions and the main results reported in the literature are compiled. Finally, the comparison between the different treatment alternatives and the presentation of potential treatment lines are postulated. Copyright © 2012 Elsevier Ltd. All rights reserved.

Design and dynamic simulation of a fixed pitch 56 kW wind turbine drive train with a continuously variable transmission

NASA Technical Reports Server (NTRS)

Gallo, C.; Kasuba, R.; Pintz, A.; Spring, J.

1986-01-01

The dynamic analysis of a horizontal axis fixed pitch wind turbine generator (WTG) rated at 56 kW is discussed. A mechanical Continuously Variable Transmission (CVT) was incorporated in the drive train to provide variable speed operation capability. One goal of the dynamic analysis was to determine if variable speed operation, by means of a mechanical CVT, is capable of capturing the transient power in the WTG/wind environment. Another goal was to determine the extent of power regulation possible with CVT operation.

High Ethanol Fuel Endurance: A Study of the Effects of Running Gasoline with 15% Ethanol Concentration in Current Production Outboard Four-Stroke Engines and Conventional Two-Stroke Outboard Marine Engines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hilbert, D.

2011-10-01

Three Mercury Marine outboard marine engines were evaluated for durability using E15 fuel -- gasoline blended with 15% ethanol. Direct comparison was made to operation on E0 (ethanol-free gasoline) to determine the effects of increased ethanol on engine durability. Testing was conducted using a 300-hour wide-open throttle (WOT) test protocol, a typical durability cycle used by the outboard marine industry. Use of E15 resulted in reduced CO emissions, as expected for open-loop, non-feedback control engines. HC emissions effects were variable. Exhaust gas and engine operating temperatures increased as a consequence of leaner operation. Each E15 test engine exhibited some deteriorationmore » that may have been related to the test fuel. The 9.9 HP, four-stroke E15 engine exhibited variable hydrocarbon emissions at 300 hours -- an indication of lean misfire. The 300HP, four-stroke, supercharged Verado engine and the 200HP, two-stroke legacy engine tested with E15 fuel failed to complete the durability test. The Verado engine failed three exhaust valves at 285 endurance hours while the 200HP legacy engine failed a main crank bearing at 256 endurance hours. All E0-dedicated engines completed the durability cycle without incident. Additional testing is necessary to link the observed engine failures to ethanol in the test fuel.« less

Electro activation of persulfate using iron sheet as low-cost electrode: the role of the operating conditions.

PubMed

Silveira, Jefferson E; Cardoso, Tais O; Barreto-Rodrigues, Marcio; Zazo, Juan A; Casas, José A

2018-05-01

This work assesses the role of the operational conditions upon the electro-activation of persulfate (PS) using sacrificed iron electrode as a continuous low-cost Fe 2+ source. An aqueous phenol solution (100 mg L -1 ) was selected as model effluent. The studied variables include current density (1-10 mA cm -2 ), persulfate concentration (0.7-2.85 g L -1 ), temperature (30-90°C) and the solution conductivity (2.7-20.7 mS cm -1 ) using Na 2 SO 4 and NaCl as supporting electrolyte. A mineralization degree of around 80% with Na 2 SO 4 and 92% in presence of NaCl was achieved at 30°C using 2.15 g L -1 PS at the lowest current density tested (1 mA cm -2 ). Besides PS concentration, temperature was the main variable affecting the process. In the range of 30-70°C, it showed a positive effect, achieving TOC conversion above 95% (using Na 2 SO 4 under the previous conditions) along with a significant increase in iron sludge, which adversely affects the economy of the process. A lumped and simplified kinetic model based on persulfate consumption and TOC mineralization is suggested. The activation energy obtained for the TOC decay was 29 kJ mol -1 . An estimated operating cost of US$ 3.00 per m 3 was obtained, demonstrating the economic feasibility of this process.

Main components and characteristics of landslide early warning systems operational worldwide

NASA Astrophysics Data System (ADS)

Piciullo, Luca; Cepeda, José

2017-04-01

During the last decades the number of victims and economic losses due to natural hazards are dramatically increased worldwide. The reason can be mainly ascribed to climate changes and urbanization in areas exposed at high level of risk. Among the many mitigation measures available for reducing the risk to life related to natural hazards, early warning systems certainly constitute a significant cost-effective option available to the authorities in charge of risk management and governance. The aim is to help and protect populations exposed to natural hazards, reducing fatalities when major events occur. Landslide is one of the natural hazards addressed by early warning systems. Landslide early warning systems (LEWSs) are mainly composed by the following four components: set-up, correlation laws, decisional algorithm and warning management. Within this framework, the set-up includes all the preliminary actions and choices necessary for designing a LEWS, such as: the area covered by the system, the types of landslides and the monitoring instruments. The monitoring phase provides a series of important information on different variables, considered as triggering factors for landslides, in order to define correlation laws and thresholds. Then, a decisional algorithm is necessary for defining the: number of warning levels to be employed in the system, decision making procedures, and everything else system managers may need for issuing warnings in different warning zones. Finally the warning management is composed by: monitoring and warning strategy; communication strategy; emergency plan and, everything connected to the social sphere. Among LEWSs operational worldwide, two categories can be defined as a function of the scale of analysis: "local" and "territorial" systems. The scale of analysis influences several actions and aspects connected to the design and employment of the system, such as: the actors involved, the monitoring systems, type of landslide phenomena addressed and variables to be considered for correlations. The characteristics of LEWSs at local scale are strongly affected by numerous constraints and factors, from time to time different, related to the characteristics of the problem they address. Monitoring measures, variables and correlation laws considered for the design and employment of local LEWSs, strongly depends on the type of landslide to be addressed. On the other hand, territorial LEWSs mainly deals with rainfall-induced landslides characterized by fast slope movement. These systems have become a risk management approach, employed worldwide over areas of relevant extension. Before 2005 only few experiences of LEWSs at a regional scale were carried out, such as in: Hong Kong, China; Zhejiang Province, China; San Francisco Bay, California, USA; Appalachians, USA; Oregon, USA; Rio de Janeiro, Brazil. Since the beginning of the XXI century, increased knowledge on rainfall-landslide correlations and upgraded technologies in weather forecast have promoted the development and improvement of territorial LEWSs around the world.

Hydraulic Geometry Characteristics of Continuous-Record Streamflow-Gaging Stations on Four Urban Watersheds Along the Main Stem of Gwynns Falls, Baltimore County and Baltimore City, Maryland

USGS Publications Warehouse

Doheny, Edward J.; Fisher, Gary T.

2007-01-01

Four continuous-record streamflow-gaging stations are currently being operated by the U.S. Geological Survey on the main stem of Gwynns Falls in western Baltimore County and Baltimore City, Maryland. The four streamflow-gaging stations drain urban or suburban watersheds with significantly different drainage areas. In addition to providing continuous- record discharge data at these four locations, operation of these stations also provides a long-term record of channel geometry variables such as cross-sectional area, channel width, mean channel depth, and mean velocity that are obtained from physical measurement of the discharge at a variety of flow conditions. Hydraulic geometry analyses were performed using discharge-measurement data from four continuous-record streamflow-gaging stations on the main stem of Gwynns Falls. Simple linear regression was used to develop relations that (1) quantify changes in cross-sectional area, channel width, mean channel depth, and mean velocity with changes in discharge at each station, and (2) quantify changes in these variables in the Gwynns Falls watershed with changes in drainage area and annual mean discharge. Results of the hydraulic geometry analyses indicated that mean velocity is more responsive to changes in discharge than channel width and mean channel depth for all four streamflow-gaging stations on the main stem of Gwynns Falls. For the two largest and most developed watersheds, on Gwynns Falls at Villa Nova, and Gwynns Falls at Washington Boulevard at Baltimore, the slope of the regression lines, or hydraulic exponents, indicated that mean velocity was more responsive to changes in discharge than any of the other hydraulic variables that were analyzed. This was true even when considering changes in cross-sectional area with discharge, which incorporates the combined effects of channel width and mean channel depth. A comparison of hydraulic exponents for Gwynns Falls to average values from previous work indicated that the velocity exponents for all four stations on the Gwynns Falls are larger than the average value of 0.34. For stations 01589300 and 01589352, the exponents for mean velocity are about twice as large as the average value. Analyses of cross-sectional area, channel width, mean channel depth, and mean velocity in conjunction with changes in drainage area and annual mean discharge indicated that channel width is much more responsive to changes in drainage area and annual mean discharge than are mean channel depth or mean velocity. Cross-sectional area, which combines the effects of channel width and mean channel depth, was also found to be highly responsive to changes in drainage area and annual mean discharge.

Non-Asbestos Insulation Testing Using a Plasma Torch

NASA Technical Reports Server (NTRS)

Morgan, R. E.; Prince, A. S.; Selvidge, S. A.; Phelps, J.; Martin, C. L.; Lawrence, T. W.

2000-01-01

Insulation obsolescence issues are a major concern for the Reusable Solid Rocket Motor (RSRM). As old sources of raw materials disappear, new sources must be found and qualified. No simple, inexpensive test presently exists for predicting the erosion performance of a candidate insulation in the full-scale motor, Large motor tests cost million of dollars and therefore can only be used on a few very select candidates. There is a need for a simple, low cost method of screening insulation performance that can simulate some of the different erosion environments found in the RSRM. This paper describes a series of erosion tests on two different non-asbestos insulation formulations, a KEVLAR(registered) fiber-filled and a carbon fiber-filled insulation containing Ethylene-Propylene-Diene Monomer (EPDM) rubber as the binder. The test instrument was a plasma torch device. The two main variables investigated were heat flux and alumina particle impingement concentration. Statistical analysis revealed that the two different formulations had very different responses to the main variable. The results of this work indicate that there may be fundamental differences in how these insulation formulations perform in the motor operating environment. The plasma torch appears to offer a low-cost means of obtaining a fundamental understanding of insulation response to critical factors in a series of statistically designed experiments.

Machines that Go 'Ping': Medical Technology and Health Expenditures in OECD Countries.

PubMed

Willemé, Peter; Dumont, Michel

2015-08-01

Technology is believed to be a major determinant of increasing health spending. The main difficulty to quantify its effect is to find suitable proxies to measure medical technological innovation. This paper's main contribution is the use of data on approved medical devices and drugs to proxy for medical technology. The effects of these variables on total real per capita health spending are estimated using a panel model for 18 Organisation for Economic Co-operation and Development (OECD) countries covering the period 1981-2012. The results confirm the substantial cost-increasing effect of medical technology, which accounts for almost 50% of the explained historical growth of spending. Despite the overall net positive effect of technology, the effect of two subgroups of approvals on expenditure is significantly negative. These subgroups can be thought of as representing 'incremental medical innovation', whereas the positive effects are related to radically innovative pharmaceutical products and devices. A separate time series model was estimated for the USA because the FDA approval data in fact only apply to the USA, while they serve as proxies for the other OECD countries. Our empirical model includes an indicator of obesity, and estimations confirm the substantial contribution of this lifestyle variable to health spending growth in the countries studied. Copyright © 2014 John Wiley & Sons, Ltd.

Mesoscale structure of microplankton and mesoplankton assemblages under contrasting oceanographic conditions in the Catalan Sea (NW Mediterranean)

NASA Astrophysics Data System (ADS)

Villate, Fernando; Uriarte, Ibon; Olivar, M. Pilar; Maynou, Francesc; Emelianov, Mikhail; Ameztoy, Iban

2014-11-01

The abundance, composition and mesoscale variability of the microplankton (53-200 μm) and the mesoplankton (0.2-2 mm) fractions in relation to oceanographic factors and phytoplankton biomass were compared off the Catalan coast (NW Mediterranean) during the summer stratification (June) and autumn mixing (November) periods in 2005. This work aims to determine whether the two plankton fractions that more contribute to fish larval diet respond to a common variable environment, and this study constitutes the first attempt to analyse, in parallel, the spatial structure of both fractions in this area. From June to November microplankton abundance increased mainly by the increase of dinoflagellates, tintinnids and radiolarians, and mesoplankton decreased due mainly to the decrease of long-horned dinoflagellates, cladocerans, doliolids and appendicularians. Plankton mesoscale variability in relation to environmental variables showed higher complexity in June, where environmental horizontal and vertical gradients were more marked than in November. In June, the major mode of variability of the microplankton was mainly accounted by the patchy distribution of several tintinnid species dominated by Rhabdonella spiralis associated to the subsurface phytoplankton biomass. The main mode of variability of the mesoplankton was related to the intrusion of the Ebro river plume and the related aggregation of doliolids and cladocerans, dominated by Evadne spinifera. In November, the major variability pattern in both fractions was a combination of inshore-offshore and eastern-western gradients in taxa distributions shaped mainly by the course of the Catalan Current along the shelf-break. Spatial differences in planktonic food pathways in each period are discussed on the basis of literature on plankton feeding habits and types, and on the diet of fish larvae of the main species from the same surveys.

Surgeon and type of anesthesia predict variability in surgical procedure times.

PubMed

Strum, D P; Sampson, A R; May, J H; Vargas, L G

2000-05-01

Variability in surgical procedure times increases the cost of healthcare delivery by increasing both the underutilization and overutilization of expensive surgical resources. To reduce variability in surgical procedure times, we must identify and study its sources. Our data set consisted of all surgeries performed over a 7-yr period at a large teaching hospital, resulting in 46,322 surgical cases. To study factors associated with variability in surgical procedure times, data mining techniques were used to segment and focus the data so that the analyses would be both technically and intellectually feasible. The data were subdivided into 40 representative segments of manageable size and variability based on headers adopted from the common procedural terminology classification. Each data segment was then analyzed using a main-effects linear model to identify and quantify specific sources of variability in surgical procedure times. The single most important source of variability in surgical procedure times was surgeon effect. Type of anesthesia, age, gender, and American Society of Anesthesiologists risk class were additional sources of variability. Intrinsic case-specific variability, unexplained by any of the preceding factors, was found to be highest for shorter surgeries relative to longer procedures. Variability in procedure times among surgeons was a multiplicative function (proportionate to time) of surgical time and total procedure time, such that as procedure times increased, variability in surgeons' surgical time increased proportionately. Surgeon-specific variability should be considered when building scheduling heuristics for longer surgeries. Results concerning variability in surgical procedure times due to factors such as type of anesthesia, age, gender, and American Society of Anesthesiologists risk class may be extrapolated to scheduling in other institutions, although specifics on individual surgeons may not. This research identifies factors associated with variability in surgical procedure times, knowledge of which may ultimately be used to improve surgical scheduling and operating room utilization.

Multiagent Systems Based Modeling and Implementation of Dynamic Energy Management of Smart Microgrid Using MACSimJX.

PubMed

Raju, Leo; Milton, R S; Mahadevan, Senthilkumaran

The objective of this paper is implementation of multiagent system (MAS) for the advanced distributed energy management and demand side management of a solar microgrid. Initially, Java agent development environment (JADE) frame work is used to implement MAS based dynamic energy management of solar microgrid. Due to unstable nature of MATLAB, when dealing with multithreading environment, MAS operating in JADE is linked with the MATLAB using a middle ware called Multiagent Control Using Simulink with Jade Extension (MACSimJX). MACSimJX allows the solar microgrid components designed with MATLAB to be controlled by the corresponding agents of MAS. The microgrid environment variables are captured through sensors and given to agents through MATLAB/Simulink and after the agent operations in JADE, the results are given to the actuators through MATLAB for the implementation of dynamic operation in solar microgrid. MAS operating in JADE maximizes operational efficiency of solar microgrid by decentralized approach and increase in runtime efficiency due to JADE. Autonomous demand side management is implemented for optimizing the power exchange between main grid and microgrid with intermittent nature of solar power, randomness of load, and variation of noncritical load and grid price. These dynamics are considered for every time step and complex environment simulation is designed to emulate the distributed microgrid operations and evaluate the impact of agent operations.

Multiagent Systems Based Modeling and Implementation of Dynamic Energy Management of Smart Microgrid Using MACSimJX

PubMed Central

Raju, Leo; Milton, R. S.; Mahadevan, Senthilkumaran

2016-01-01

The objective of this paper is implementation of multiagent system (MAS) for the advanced distributed energy management and demand side management of a solar microgrid. Initially, Java agent development environment (JADE) frame work is used to implement MAS based dynamic energy management of solar microgrid. Due to unstable nature of MATLAB, when dealing with multithreading environment, MAS operating in JADE is linked with the MATLAB using a middle ware called Multiagent Control Using Simulink with Jade Extension (MACSimJX). MACSimJX allows the solar microgrid components designed with MATLAB to be controlled by the corresponding agents of MAS. The microgrid environment variables are captured through sensors and given to agents through MATLAB/Simulink and after the agent operations in JADE, the results are given to the actuators through MATLAB for the implementation of dynamic operation in solar microgrid. MAS operating in JADE maximizes operational efficiency of solar microgrid by decentralized approach and increase in runtime efficiency due to JADE. Autonomous demand side management is implemented for optimizing the power exchange between main grid and microgrid with intermittent nature of solar power, randomness of load, and variation of noncritical load and grid price. These dynamics are considered for every time step and complex environment simulation is designed to emulate the distributed microgrid operations and evaluate the impact of agent operations. PMID:27127802

Simulation of long-term influence from technical systems on permafrost with various short-scale and hourly operation modes in Arctic region

NASA Astrophysics Data System (ADS)

Vaganova, N. A.

2017-12-01

Technogenic and climatic influences have a significant impact on the degradation of permafrost. Long-term forecasts of such changes during long-time periods have to be taken into account in the oil and gas and construction industries in view to development the Arctic and Subarctic regions. There are considered constantly operating technical systems (for example, oil and gas wells) that affect changes in permafrost, as well as the technical systems that have a short-term impact on permafrost (for example, flare systems for emergency flaring of associated gas). The second type of technical systems is rather complex for simulation, since it is required to reserve both short and long-scales in computations with variable time steps describing the complex technological processes. The main attention is paid to the simulation of long-term influence on the permafrost from the second type of the technical systems.

Location of Opening-Out Cross-Cuts in Relation to Rockburst Hazard Conditions along the Face in the Light of Model Testing

NASA Astrophysics Data System (ADS)

Chlebowski, Dariusz; Zorychta, Andrzej; Burtan, Zbigniew; Cała, Marek

2017-03-01

The paper outlines the main objectives of the method used for assessment of rockburst hazard during longwall mining operations taking into account factors expressing the confined work conditions. Relying on analytical approach, the conditions are examined that are likely to trigger the rockburst occurrence along the face, with regards to the location of cross-cuts and taking into account the presence of past excavation and geological disorders in the overlying strata. Simulation data apply to three cases of model loading, representing the impacts of residual pillars, gobs surrounded by undisturbed blocks of coal and the presence of faults, whilst the procedure involves five possible locations of opening-out cross-cuts in relation to characteristic points in the model. Results are examined basing on variability patterns of stress concentration and energy density distribution in the proximity of the workface in the course of progressing mining operations.

Modeling biosorption of Cr(VI) onto Ulva compressa L. from aqueous solutions.

PubMed

Aid, Asma; Amokrane, Samira; Nibou, Djamel; Mekatel, Elhadj; Trari, Mohamed; Hulea, Vasile

2018-01-01

The marine biomass Ulva compressa L. (ECL) was used as a low-cost biosorbent for the removal of Cr(VI) from contaminated aqueous solutions. The operating variables were optimized: pH ∼ 2, initial concentration of 25 mg/L, solid/liquid ratio of 6 g/L and a temperature of 50 °C, leading to an uptake elimination of 96%. A full factorial experimental design technique enabled us to obtain a mathematical model describing the Cr(VI) biosorption and to study the main effects and interactions among operational parameters. The equilibrium isotherm was analyzed by the Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models; it has been found that the adsorption process follows well the Langmuir model. Kinetic studies showed that the pseudo-second order model describes suitably the experimental data. The thermodynamic parameters indicated an endothermic heat and a spontaneity of the Cr(VI) biosorption onto ECL.

Viscoplastic analysis of an experimental cylindrical thrust chamber liner

NASA Technical Reports Server (NTRS)

Arya, Vinod K.; Arnold, Steven M.

1991-01-01

A viscoplastic stress-strain analysis of an experimental cylindrical thrust chamber is presented. A viscoelastic constitutive model incorporating a single internal state variable that represents kinematic hardening was employed to investigate whether such a viscoplastic model could predict the experimentally observed behavior of the thrust chamber. Two types of loading cycles were considered: a short cycle of 3.5 sec. duration that corresponded to the experiments, and an extended loading cycle of 485.1 sec. duration that is typical of the Space Shuttle Main Engine (SSME) operating cycle. The analysis qualitatively replicated the deformation behavior of the component as observed in experiments designed to simulate SSME operating conditions. The analysis also showed that the mode and location in the component may depend on the loading cycle. The results indicate that using viscoplastic models for structural analysis can lead to a more realistic life assessment of thrust chambers.

Smart garments for safety improvement of emergency/disaster operators.

PubMed

Curone, Davide; Dudnik, Gabriela; Loriga, Giannicola; Luprano, Jean; Magenes, Giovanni; Paradiso, Rita; Tognetti, Alessandro; Bonfiglio, Annalisa

2007-01-01

The main purpose of the European project ProeTEX is to develop equipment to improve safety, coordination and efficiency of emergency disaster intervention personnel like fire-fighters or civil protection rescuers. The equipment consists of a new generation of "smart" garments, integrating wearable sensors which will allow monitoring physiological parameters, position and activity of the user, as like as environmental variables of the operating field in which rescuers are working: both commercial and newly developed textile and fibre based sensors will be included. The garments will also contain an electronic box to process data collected by the sensors and a communication system enabling the transmission of data to the other rescuers and to a monitoring station. Also a "smart" victim patch will be developed: a wearable garment which will allow monitoring physiological parameters of injured civilians involved in disasters, with the aim of optimizing their survival management.

Prediction of alpha factor values for fine pore aeration systems.

PubMed

Gillot, S; Héduit, A

2008-01-01

The objective of this work was to analyse the impact of different geometric and operating parameters on the alpha factor value for fine bubble aeration systems equipped with EPDM membrane diffusers. Measurements have been performed on nitrifying plants operating under extended aeration and treating mainly domestic wastewater. Measurements performed on 14 nitrifying plants showed that, for domestic wastewater treatment under very low F/M ratios, the alpha factor is comprised between 0.44 and 0.98. A new composite variable (the Equivalent Contact Time, ECT) has been defined and makes it possible for a given aeration tank, knowing the MCRT, the clean water oxygen transfer coefficient and the supplied air flow rate, to predict the alpha factor value. ECT combines the effect on mass transfer of all generally accepted factors affecting oxygen transfer performances (air flow rate, diffuser submergence, horizontal flow). (c) IWA Publishing 2008.

Density-Dependent Regulation of Brook Trout Population Dynamics along a Core-Periphery Distribution Gradient in a Central Appalachian Watershed

PubMed Central

Huntsman, Brock M.; Petty, J. Todd

2014-01-01

Spatial population models predict strong density-dependence and relatively stable population dynamics near the core of a species' distribution with increasing variance and importance of density-independent processes operating towards the population periphery. Using a 10-year data set and an information-theoretic approach, we tested a series of candidate models considering density-dependent and density-independent controls on brook trout population dynamics across a core-periphery distribution gradient within a central Appalachian watershed. We sampled seven sub-populations with study sites ranging in drainage area from 1.3–60 km2 and long-term average densities ranging from 0.335–0.006 trout/m. Modeled response variables included per capita population growth rate of young-of-the-year, adult, and total brook trout. We also quantified a stock-recruitment relationship for the headwater population and coefficients of variability in mean trout density for all sub-populations over time. Density-dependent regulation was prevalent throughout the study area regardless of stream size. However, density-independent temperature models carried substantial weight and likely reflect the effect of year-to-year variability in water temperature on trout dispersal between cold tributaries and warm main stems. Estimated adult carrying capacities decreased exponentially with increasing stream size from 0.24 trout/m in headwaters to 0.005 trout/m in the main stem. Finally, temporal variance in brook trout population size was lowest in the high-density headwater population, tended to peak in mid-sized streams and declined slightly in the largest streams with the lowest densities. Our results provide support for the hypothesis that local density-dependent processes have a strong control on brook trout dynamics across the entire distribution gradient. However, the mechanisms of regulation likely shift from competition for limited food and space in headwater streams to competition for thermal refugia in larger main stems. It also is likely that source-sink dynamics and dispersal from small headwater habitats may partially influence brook trout population dynamics in the main stem. PMID:24618602

Hurricane intensification along United States coast suppressed during active hurricane periods

NASA Astrophysics Data System (ADS)

Kossin, James P.

2017-01-01

The North Atlantic ocean/atmosphere environment exhibits pronounced interdecadal variability that is known to strongly modulate Atlantic hurricane activity. Variability in sea surface temperature (SST) is correlated with hurricane variability through its relationship with the genesis and thermodynamic potential intensity of hurricanes. Another key factor that governs the genesis and intensity of hurricanes is ambient environmental vertical wind shear (VWS). Warmer SSTs generally correlate with more frequent genesis and greater potential intensity, while VWS inhibits genesis and prevents any hurricanes that do form from reaching their potential intensity. When averaged over the main hurricane-development region in the Atlantic, SST and VWS co-vary inversely, so that the two factors act in concert to either enhance or inhibit basin-wide hurricane activity. Here I show, however, that conditions conducive to greater basin-wide Atlantic hurricane activity occur together with conditions for more probable weakening of hurricanes near the United States coast. Thus, the VWS and SST form a protective barrier along the United States coast during periods of heightened basin-wide hurricane activity. Conversely, during the most-recent period of basin-wide quiescence, hurricanes (and particularly major hurricanes) near the United States coast, although substantially less frequent, exhibited much greater variability in their rate of intensification, and were much more likely to intensify rapidly. Such heightened variability poses greater challenges to operational forecasting and, consequently, greater coastal risk during hurricane events.

Spatiotemporal variability in wildfire patterns and analysis of the main drivers in Honduras using GIS and MODIS data

NASA Astrophysics Data System (ADS)

Valdez Vasquez, M. C.; Chen, C. F.

2017-12-01

Wildfires are unrestrained fires in an area of flammable vegetation and they are one of the most frequent disasters in Honduras during the dry season. During this period, anthropogenic activity combined with the harsh climatic conditions, dry vegetation and topographical variables, cause a large amount of wildfires. For this reason, there is a need to identify the drivers of wildfires and their susceptibility variations during the wildfire season. In this study, we combined the wildfire points during the 2010-2016 period every 8 days with a series of variables using the random forest (RF) algorithm. In addition to the wildfire points, we randomly generated a similar amount of background points that we use as pseudo-absence data. To represent the human imprint, we included proximity to different types of roads, trails, settlements and agriculture sites. Other variables included are the Moderate Resolution Imaging Spectra-radiometer (MODIS)-derived 8-day composites of land surface temperature (LST) and the normalized multi-band drought index (NMDI), derived from the MODIS surface reflectance data. We also included monthly average precipitation, solar radiation, and topographical variables. The exploratory analysis of the variables reveals that low precipitation combined with the low NMDI and accessibility to non-paved roads were the major drivers of wildfires during the early months of the dry season. During April, which is the peak of the dry season, the explanatory variables of relevance also included elevation and LST in addition to the proximity to paved and non-paved roads. During May, proximity to crops becomes relevant, in addition to the aforesaid variables. The average estimated area with high and very high wildfire susceptibility was 22% of the whole territory located mainly in the central and eastern regions, drifting towards the northeast areas during May. We validated the results using the area under the receiver operating characteristic (ROC) curve (AUC) for each 8-day period, and the average AUC acquired was acceptable using an independent test data. We suggest that the 8-day frequency spatiotemporal mapping of wildfire patterns and the identification of the most relevant drivers can lead to localized prevention and control actions in specific time-frames in areas of high wildfire susceptibility.

Steady-state and dynamic performance of a gas-lubricated seal

NASA Technical Reports Server (NTRS)

Colsher, R.; Shapiro, W.

1972-01-01

Steady-state and dynamic performance of a gas-lubricated, self-acting face seal was determined using numerical methods based on a variable grid, finite-difference, time-transient procedure. Results were obtained for a gas turbine main shaft seal operating at 206.9 newton per square centimeter (300 psi) sealed air pressure and 152.4 meters per second (500 ft/sec) sliding velocity. Analysis of the seal dynamics revealed that the response of the seal nosepiece to runout of the seat face is markedly affected by secondary seal friction and by nosepiece inertia. The nosepiece response was determined for various levels of secondary seal friction and seat face runout magnitudes.

Research activities in the field of human factors: Evaluation and prospects

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larchier-Boulanger, J.; Grosdeva, T.

1988-01-01

The industrial systems are sociotechnical i.e., conceived, directed, checked, run, and repaired by individuals belonging to structured organizations for either individual or group work. Hence, a better understanding of how their behavior, competences, and know-how is a must. At the DER and ESF department human factors group is given the mission to enlarge, through a pluridisciplinary approach, the knowledge of human factors in complex systems. Human interventions are analyzed both for their positive aspects (competences and know-how to retrieve complex situations) and their negative aspects (human weaknesses). For safety reasons such analyses are mainly directed toward the nuclear plant operators,more » considered individually (intervening of one operator) or as a team (group behavior). The aims of the studies on human factors are various, and such studies justify the research in this field. They make it possible, through a better consideration of the variables specific to individuals, to bring to the enterprise means for: (1) increasing reliability and helping performance, (2) improving the adjustment of work demands to the real environment, and (3) creating a better energy between the individual and his/her enterprise. The variables specific to human factors that keep developing thus the perspectives for research, in this field, are to recenter and redefine the undertaken studies.« less

Navigating a Mobile Robot Across Terrain Using Fuzzy Logic

NASA Technical Reports Server (NTRS)

Seraji, Homayoun; Howard, Ayanna; Bon, Bruce

2003-01-01

A strategy for autonomous navigation of a robotic vehicle across hazardous terrain involves the use of a measure of traversability of terrain within a fuzzy-logic conceptual framework. This navigation strategy requires no a priori information about the environment. Fuzzy logic was selected as a basic element of this strategy because it provides a formal methodology for representing and implementing a human driver s heuristic knowledge and operational experience. Within a fuzzy-logic framework, the attributes of human reasoning and decision- making can be formulated by simple IF (antecedent), THEN (consequent) rules coupled with easily understandable and natural linguistic representations. The linguistic values in the rule antecedents convey the imprecision associated with measurements taken by sensors onboard a mobile robot, while the linguistic values in the rule consequents represent the vagueness inherent in the reasoning processes to generate the control actions. The operational strategies of the human expert driver can be transferred, via fuzzy logic, to a robot-navigation strategy in the form of a set of simple conditional statements composed of linguistic variables. These linguistic variables are defined by fuzzy sets in accordance with user-defined membership functions. The main advantages of a fuzzy navigation strategy lie in the ability to extract heuristic rules from human experience and to obviate the need for an analytical model of the robot navigation process.

System solution to improve energy efficiency of HVAC systems

NASA Astrophysics Data System (ADS)

Chretien, L.; Becerra, R.; Salts, N. P.; Groll, E. A.

2017-08-01

According to recent surveys, heating and air conditioning systems account for over 45% of the total energy usage in US households. Three main types of HVAC systems are available to homeowners: (1) fixed-speed systems, where the compressor cycles on and off to match the cooling load; (2) multi-speed (typically, two-speed) systems, where the compressor can operate at multiple cooling capacities, leading to reduced cycling; and (3) variable-speed systems, where the compressor speed is adjusted to match the cooling load of the household, thereby providing higher efficiency and comfort levels through better temperature and humidity control. While energy consumption could reduce significantly by adopting variable-speed compressor systems, the market penetration has been limited to less than 10% of the total HVAC units and a vast majority of systems installed in new construction remains single speed. A few reasons may explain this phenomenon such as the complexity of the electronic circuitry required to vary compressor speed as well as the associated system cost. This paper outlines a system solution to boost the Seasonal Energy Efficiency Rating (SEER) of a traditional single-speed unit through using a low power electronic converter that allows the compressor to operate at multiple low capacity settings and is disabled at high compressor speeds.

The Met Office Unified Model Global Atmosphere 6.0/6.1 and JULES Global Land 6.0/6.1 configurations

NASA Astrophysics Data System (ADS)

Walters, David; Boutle, Ian; Brooks, Malcolm; Melvin, Thomas; Stratton, Rachel; Vosper, Simon; Wells, Helen; Williams, Keith; Wood, Nigel; Allen, Thomas; Bushell, Andrew; Copsey, Dan; Earnshaw, Paul; Edwards, John; Gross, Markus; Hardiman, Steven; Harris, Chris; Heming, Julian; Klingaman, Nicholas; Levine, Richard; Manners, James; Martin, Gill; Milton, Sean; Mittermaier, Marion; Morcrette, Cyril; Riddick, Thomas; Roberts, Malcolm; Sanchez, Claudio; Selwood, Paul; Stirling, Alison; Smith, Chris; Suri, Dan; Tennant, Warren; Vidale, Pier Luigi; Wilkinson, Jonathan; Willett, Martin; Woolnough, Steve; Xavier, Prince

2017-04-01

We describe Global Atmosphere 6.0 and Global Land 6.0 (GA6.0/GL6.0): the latest science configurations of the Met Office Unified Model and JULES (Joint UK Land Environment Simulator) land surface model developed for use across all timescales. Global Atmosphere 6.0 includes the ENDGame (Even Newer Dynamics for General atmospheric modelling of the environment) dynamical core, which significantly increases mid-latitude variability improving a known model bias. Alongside developments of the model's physical parametrisations, ENDGame also increases variability in the tropics, which leads to an improved representation of tropical cyclones and other tropical phenomena. Further developments of the atmospheric and land surface parametrisations improve other aspects of model performance, including the forecasting of surface weather phenomena. We also describe GA6.1/GL6.1, which includes a small number of long-standing differences from our main trunk configurations that we continue to require for operational global weather prediction. Since July 2014, GA6.1/GL6.1 has been used by the Met Office for operational global numerical weather prediction, whilst GA6.0/GL6.0 was implemented in its remaining global prediction systems over the following year.

Management Control Systems and Clinical Experience of Managers in Public Hospitals

PubMed Central

Naranjo-Gil, David

2018-01-01

Healthcare authorities are encouraging managers in hospitals to acquire clinical experience and knowledge in order to better carry out and coordinate healthcare service delivery. The main objective of this paper is to analyse how the clinical experience of hospital managers is related to public health institutions’ performance. It is proposed that the effect of the clinical experience on operative and financial organizational performance is indirect through the mediating variables of perceived utility of management information and horizontal management control system. This paper analyses how these variables impact hospital performance through the data from a survey sent to 364 hospital managers in Brazil. The results show that managers’ clinical experience is related to higher perceived utility of historical, financial, short-term, and internal information, but not with horizontal control adoption in hospitals. Furthermore, our results show that, in hospitals, perceived utility of forecasted, non-financial, long-term, and external managerial information positively affects hospitals’ financial performance, while adoption of horizontal control management positively affects operational performance. Through showing evidence that clinical background could explain the differences not only in hospital service management but also in information capabilities and management control processes, this study offer meaningful implications for healthcare authorities and hospital managers involved in the development and implementation of strategies in the health sector. PMID:29673192

Management Control Systems and Clinical Experience of Managers in Public Hospitals.

PubMed

Lunkes, Rogério Joao; Naranjo-Gil, David; Lopez-Valeiras, Ernesto

2018-04-17

Healthcare authorities are encouraging managers in hospitals to acquire clinical experience and knowledge in order to better carry out and coordinate healthcare service delivery. The main objective of this paper is to analyse how the clinical experience of hospital managers is related to public health institutions’ performance. It is proposed that the effect of the clinical experience on operative and financial organizational performance is indirect through the mediating variables of perceived utility of management information and horizontal management control system. This paper analyses how these variables impact hospital performance through the data from a survey sent to 364 hospital managers in Brazil. The results show that managers’ clinical experience is related to higher perceived utility of historical, financial, short-term, and internal information, but not with horizontal control adoption in hospitals. Furthermore, our results show that, in hospitals, perceived utility of forecasted, non-financial, long-term, and external managerial information positively affects hospitals’ financial performance, while adoption of horizontal control management positively affects operational performance. Through showing evidence that clinical background could explain the differences not only in hospital service management but also in information capabilities and management control processes, this study offer meaningful implications for healthcare authorities and hospital managers involved in the development and implementation of strategies in the health sector.

Analysis of the Effects of a Flexible Ramping Ancillary Service Product on Power System Operations: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

2015-10-19

The recent increased interest in utilizing variable generation (VG) resources such as wind and solar in power systems has motivated investigations into new operating procedures. Although these resources provide desirable value to a system (e.g., no fuel costs or emissions), interconnecting them provides unique challenges. Their variable, non-controllable nature in particular requires significant attention, because it directly results in increased power system variability and uncertainty. One way to handle this is via new operating reserve schemes. Operating reserves provide upward and downward generation and ramping capacity to counteract uncertainty and variability prior to their realization. For instance, uncertainty and variabilitymore » in real-time dispatch can be accounted for in the hour-ahead unit commitment. New operating reserve methodologies that specifically account for the increased variability and uncertainty caused by VG are currently being investigated and developed by academia and industry. This paper examines one method inspired by the new operating reserve product being proposed by the California Independent System Operator. The method is based on examining the potential ramping requirements at any given time and enforcing those requirements via a reserve demand curve in the market-clearing optimization as an additional ancillary service product.« less

Water management to cope with and adapt to climate variability and change.

NASA Astrophysics Data System (ADS)

Hamdy, A.; Trisorio-Liuzzi, G.

2009-04-01

In many parts of the world, variability in climatic conditions is already resulting in major impacts. These impacts are wide ranging and the link to water management problems is obvious and profound. The know-how and the available information undoubtedly indicate that climate change will lead to an intensification of the global hydrological cycle and can have major impacts on regional water resources, affecting both ground and surface water supply for sectorial water uses and, in particular, the irrigation field imposing notable negative effects on food security and poverty alleviation programs in most arid and semi-arid developing countries. At the United Nations Millennium Summit, in September 2000, world leaders adopted the Millennium Development Declaration. From this declaration, the IWRM was recognised as the key concept the water sector should be using for water related development and measures and, hence, for achieving the water related MDG's. However, the potential impacts of climate change and increasing climate variability are not sufficiently addressed in the IWRM plans. Indeed, only a very limited IWRM national plans have been prepared, coping with climate variability and changes. This is mainly due to the lack of operational instruments to deal with climate change and climate variability issues. This is particularly true in developing countries where the financial, human and ecological impacts are potentially greatest and where water resources may be already highly stressed, but the capacity to cope and adapt is weakest. Climate change has now brought realities including mainly rising temperatures and increasing frequency of floods and droughts that present new challenges to be addressed by the IWRM practice. There are already several regional and international initiatives underway that focus on various aspects of water resources management those to be linked with climate changes and vulnerability issues. This is the way where the water resources management and climate scientist communities are engaged in a process for building confidence and understanding, identifying options and defining the water resources management strategies which to cope with impacts of climate variability and change.

Safety models incorporating graph theory based transit indicators.

PubMed

Quintero, Liliana; Sayed, Tarek; Wahba, Mohamed M

2013-01-01

There is a considerable need for tools to enable the evaluation of the safety of transit networks at the planning stage. One interesting approach for the planning of public transportation systems is the study of networks. Network techniques involve the analysis of systems by viewing them as a graph composed of a set of vertices (nodes) and edges (links). Once the transport system is visualized as a graph, various network properties can be evaluated based on the relationships between the network elements. Several indicators can be calculated including connectivity, coverage, directness and complexity, among others. The main objective of this study is to investigate the relationship between network-based transit indicators and safety. The study develops macro-level collision prediction models that explicitly incorporate transit physical and operational elements and transit network indicators as explanatory variables. Several macro-level (zonal) collision prediction models were developed using a generalized linear regression technique, assuming a negative binomial error structure. The models were grouped into four main themes: transit infrastructure, transit network topology, transit route design, and transit performance and operations. The safety models showed that collisions were significantly associated with transit network properties such as: connectivity, coverage, overlapping degree and the Local Index of Transit Availability. As well, the models showed a significant relationship between collisions and some transit physical and operational attributes such as the number of routes, frequency of routes, bus density, length of bus and 3+ priority lanes. Copyright © 2012 Elsevier Ltd. All rights reserved.

Combining Variables, Controlling Variables, and Proportions: Is There a Psychological Link?

ERIC Educational Resources Information Center

Lawson, Anton E.

1979-01-01

Investigated the degree of relationship among the performance of 28 seventh grade students on the following three formal operations tasks: chemical combinations, bending rods, and balance beam. Results show that task performance ranged widely from early concrete operational to fully operational. (HM)

Selection of optimal complexity for ENSO-EMR model by minimum description length principle

NASA Astrophysics Data System (ADS)

Loskutov, E. M.; Mukhin, D.; Mukhina, A.; Gavrilov, A.; Kondrashov, D. A.; Feigin, A. M.

2012-12-01

One of the main problems arising in modeling of data taken from natural system is finding a phase space suitable for construction of the evolution operator model. Since we usually deal with strongly high-dimensional behavior, we are forced to construct a model working in some projection of system phase space corresponding to time scales of interest. Selection of optimal projection is non-trivial problem since there are many ways to reconstruct phase variables from given time series, especially in the case of a spatio-temporal data field. Actually, finding optimal projection is significant part of model selection, because, on the one hand, the transformation of data to some phase variables vector can be considered as a required component of the model. On the other hand, such an optimization of a phase space makes sense only in relation to the parametrization of the model we use, i.e. representation of evolution operator, so we should find an optimal structure of the model together with phase variables vector. In this paper we propose to use principle of minimal description length (Molkov et al., 2009) for selection models of optimal complexity. The proposed method is applied to optimization of Empirical Model Reduction (EMR) of ENSO phenomenon (Kravtsov et al. 2005, Kondrashov et. al., 2005). This model operates within a subset of leading EOFs constructed from spatio-temporal field of SST in Equatorial Pacific, and has a form of multi-level stochastic differential equations (SDE) with polynomial parameterization of the right-hand side. Optimal values for both the number of EOF, the order of polynomial and number of levels are estimated from the Equatorial Pacific SST dataset. References: Ya. Molkov, D. Mukhin, E. Loskutov, G. Fidelin and A. Feigin, Using the minimum description length principle for global reconstruction of dynamic systems from noisy time series, Phys. Rev. E, Vol. 80, P 046207, 2009 Kravtsov S, Kondrashov D, Ghil M, 2005: Multilevel regression modeling of nonlinear processes: Derivation and applications to climatic variability. J. Climate, 18 (21): 4404-4424. D. Kondrashov, S. Kravtsov, A. W. Robertson and M. Ghil, 2005. A hierarchy of data-based ENSO models. J. Climate, 18, 4425-4444.

Spray-drying nanocapsules in presence of colloidal silica as drying auxiliary agent: formulation and process variables optimization using experimental designs.

PubMed

Tewa-Tagne, Patrice; Degobert, Ghania; Briançon, Stéphanie; Bordes, Claire; Gauvrit, Jean-Yves; Lanteri, Pierre; Fessi, Hatem

2007-04-01

Spray-drying process was used for the development of dried polymeric nanocapsules. The purpose of this research was to investigate the effects of formulation and process variables on the resulting powder characteristics in order to optimize them. Experimental designs were used in order to estimate the influence of formulation parameters (nanocapsules and silica concentrations) and process variables (inlet temperature, spray-flow air, feed flow rate and drying air flow rate) on spray-dried nanocapsules when using silica as drying auxiliary agent. The interactions among the formulation parameters and process variables were also studied. Responses analyzed for computing these effects and interactions were outlet temperature, moisture content, operation yield, particles size, and particulate density. Additional qualitative responses (particles morphology, powder behavior) were also considered. Nanocapsules and silica concentrations were the main factors influencing the yield, particulate density and particle size. In addition, they were concerned for the only significant interactions occurring among two different variables. None of the studied variables had major effect on the moisture content while the interaction between nanocapsules and silica in the feed was of first interest and determinant for both the qualitative and quantitative responses. The particles morphology depended on the feed formulation but was unaffected by the process conditions. This study demonstrated that drying nanocapsules using silica as auxiliary agent by spray drying process enables the obtaining of dried micronic particle size. The optimization of the process and the formulation variables resulted in a considerable improvement of product yield while minimizing the moisture content.

Within and between Individual Variability of Exposure to Work-Related Musculoskeletal Disorder Risk Factors.

PubMed

Zare, Mohsen; Sagot, Jean-Claude; Roquelaure, Yves

2018-05-17

Industrial companies indicate a tendency to eliminate variations in operator strategies, particularly following implementation of the lean principle. Companies believe when the operators perform the same prescribed tasks, they have to execute them in the same manner (completing the same gestures and being exposed to the same risk factors). They attempt to achieve better product quality by standardizing and reducing operational leeway. However, operators adjust and modify ways of performing tasks to balance between their abilities and the requirements of the job. This study aims to investigate the variability of exposure to physical risk factors within and between operators when executing the same prescribed tasks. The Ergonomic Standard method was used to evaluate two workstations. Seven operators were observed thirty times between repeated cycle times at those workstations. The results revealed the variability of exposure to risk factors between and within operators in the repeated execution of the same tasks. Individual characteristics and operators' strategies might generate the variability of exposure to risk factors that may be an opportunity to reduce the risks of work-related musculoskeletal disorders (WR-MSDs). However, sometimes operators' strategies may cause overexposure to risk factors; operators most often adopt such strategies to undertake their tasks while reducing the workload.

Plant Responses to Climate Change: The Case Study of Betulaceae and Poaceae Pollen Seasons (Northern Italy, Vignola, Emilia-Romagna)

PubMed Central

Mercuri, Anna Maria; Torri, Paola; Fornaciari, Rita; Florenzano, Assunta

2016-01-01

Aerobiological data have especially demonstrated that there is correlation between climate warming and the pollination season of plants. This paper focuses on airborne pollen monitoring of Betulaceae and Poaceae, two of the main plant groups with anemophilous pollen and allergenic proprieties in Northern Italy. The aim is to investigate plant responses to temperature variations by considering long-term pollen series. The 15-year aerobiological analysis is reported from the monitoring station of Vignola (located near Modena, in the Emilia-Romagna region) that had operated in the years 1990–2004 with a Hirst spore trap. The Yearly Pollen Index calculated for these two botanical families has shown contrasting trends in pollen production and release. These trends were well identifiable but fairly variable, depending on both meteorological variables and anthropogenic causes. Based on recent reference literature, we considered that some oscillations in pollen concentration could have been a main effect of temperature variability reflecting global warming. The duration of pollen seasons of Betulaceae and Poaceae, depending on the different species included in each family, has not unequivocally been determined. Phenological responses were particularly evident in Alnus and especially in Corylus as a general moving up of the end of pollination. The study shows that these trees can be affected by global warming more than other, more tolerant, plants. The research can be a contribution to the understanding of phenological plant responses to climate change and suggests that alder and hazelnut trees have to be taken into high consideration as sensible markers of plant responses to climate change. PMID:27929423

Plant Responses to Climate Change: The Case Study of Betulaceae and Poaceae Pollen Seasons (Northern Italy, Vignola, Emilia-Romagna).

PubMed

Mercuri, Anna Maria; Torri, Paola; Fornaciari, Rita; Florenzano, Assunta

2016-12-06

Aerobiological data have especially demonstrated that there is correlation between climate warming and the pollination season of plants. This paper focuses on airborne pollen monitoring of Betulaceae and Poaceae, two of the main plant groups with anemophilous pollen and allergenic proprieties in Northern Italy. The aim is to investigate plant responses to temperature variations by considering long-term pollen series. The 15-year aerobiological analysis is reported from the monitoring station of Vignola (located near Modena, in the Emilia-Romagna region) that had operated in the years 1990-2004 with a Hirst spore trap. The Yearly Pollen Index calculated for these two botanical families has shown contrasting trends in pollen production and release. These trends were well identifiable but fairly variable, depending on both meteorological variables and anthropogenic causes. Based on recent reference literature, we considered that some oscillations in pollen concentration could have been a main effect of temperature variability reflecting global warming. The duration of pollen seasons of Betulaceae and Poaceae, depending on the different species included in each family, has not unequivocally been determined. Phenological responses were particularly evident in Alnus and especially in Corylus as a general moving up of the end of pollination. The study shows that these trees can be affected by global warming more than other, more tolerant, plants. The research can be a contribution to the understanding of phenological plant responses to climate change and suggests that alder and hazelnut trees have to be taken into high consideration as sensible markers of plant responses to climate change.

Dynamics of Postcombustion CO2 Capture Plants: Modeling, Validation, and Case Study

PubMed Central

2017-01-01

The capture of CO2 from power plant flue gases provides an opportunity to mitigate emissions that are harmful to the global climate. While the process of CO2 capture using an aqueous amine solution is well-known from experience in other technical sectors (e.g., acid gas removal in the gas processing industry), its operation combined with a power plant still needs investigation because in this case, the interaction with power plants that are increasingly operated dynamically poses control challenges. This article presents the dynamic modeling of CO2 capture plants followed by a detailed validation using transient measurements recorded from the pilot plant operated at the Maasvlakte power station in the Netherlands. The model predictions are in good agreement with the experimental data related to the transient changes of the main process variables such as flow rate, CO2 concentrations, temperatures, and solvent loading. The validated model was used to study the effects of fast power plant transients on the capture plant operation. A relevant result of this work is that an integrated CO2 capture plant might enable more dynamic operation of retrofitted fossil fuel power plants because the large amount of steam needed by the capture process can be diverted rapidly to and from the power plant. PMID:28413256

Prevalence of cataract surgery and visual outcomes in Indian immigrants in Singapore: the Singapore Indian eye study.

PubMed

Gupta, Preeti; Zheng, Yingfeng; Ting, Tay Wan; Lamoureux, Ecosse L; Cheng, Ching-Yu; Wong, Tien-Yin

2013-01-01

To determine the prevalence of cataract surgery and factors associated with post-surgical visual outcomes in migrant Indians living in Singapore. We conducted a population-based study in 3,400 Indian immigrants residing in Singapore-the Singapore Indian Eye Study (SINDI). All participants underwent comprehensive medical eye examination and a standardized interview. Post-operative visual impairment (VI) was defined as best-corrected or presenting visual acuity (BCVA or PVA) of 20/60 or worse. The age- and gender-standardized prevalence of cataract surgery was 9.7% (95% confidence interval [CI]: 8.9%, 10.7%) in Singapore resident Indians. Post-operative VI defined by BCVA occurred in 10.9% eyes (87/795). The main causes of post-operative VI were diabetic retinopathy (20.7%), posterior capsular opacification (18.4%), and age-related macular degeneration (12.6%). Undercorrected refractive error doubled the prevalence of post-operative VI when PVA was used. The rate of cataract surgery is about 10% in Indian residents in Singapore. Socioeconomic variables and migration had no significant impact on the prevalence of cataract surgery. Diabetic retinopathy was a major cause of post-operative VI in migrant Indians living in Singapore. Uncorrected postoperative refractive error remains an efficient way to improve vision.

Basic principles of variable speed drives

NASA Technical Reports Server (NTRS)

Loewenthal, S. H.

1973-01-01

An understanding of the principles which govern variable speed drive operation is discussed for successful drive application. The fundamental factors of torque, speed ratio, and power as they relate to drive selection are discussed. The basic types of variable speed drives, their operating characteristics and their applications are also presented.

Pre-main sequence variables in young cluster Stock 18

NASA Astrophysics Data System (ADS)

Sinha, Tirthendu; Sharma, Saurabh; Pandey, Rakesh; Pandey, Anil Kumar

2018-04-01

We have carried out multi-epoch deep I band photometry of the open cluster Stock 18 to search for variable stars in star forming regions. In the present study, we identified 65 periodic and 217 non-periodic variable stars. The periods of most of the periodic variables are between 2 hours to 15 days and their magnitude varies between 0.05 to 0.6 mag. We have derived spectral energy distributions for 48 probable pre-main sequence variables. Their average age and mass are 2.7 ± 0.3 Myrs and 2.7 ± 0.2 Mo, respectively.

Thermoelectric power generator for variable thermal power source

DOEpatents

Bell, Lon E; Crane, Douglas Todd

2015-04-14

Traditional power generation systems using thermoelectric power generators are designed to operate most efficiently for a single operating condition. The present invention provides a power generation system in which the characteristics of the thermoelectrics, the flow of the thermal power, and the operational characteristics of the power generator are monitored and controlled such that higher operation efficiencies and/or higher output powers can be maintained with variably thermal power input. Such a system is particularly beneficial in variable thermal power source systems, such as recovering power from the waste heat generated in the exhaust of combustion engines.

Impact of the operation of cascade reservoirs in upper Yangtze River on hydrological variability of the mainstream

NASA Astrophysics Data System (ADS)

Changjiang, Xu; Dongdong, Zhang

2018-06-01

As the impacts by climate changes and human activities are intensified, variability may occur in river's annual runoff as well as flood and low water characteristics. In order to understand the characteristics of variability in hydrological series, diagnosis and identification must be conducted specific to the variability of hydrological series, i.e., whether there was variability and where the variability began to occur. In this paper, the mainstream of Yangtze River was taken as the object of study. A model was established to simulate the impounding and operation of upstream cascade reservoirs so as to obtain the runoff of downstream hydrological control stations after the regulation by upstream reservoirs in different level years. The Range of Variability Approach was utilized to analyze the impact of the operation of upstream reservoirs on the variability of downstream. The results indicated that the overall hydrologic alterations of Yichang hydrological station in 2010 level year, 2015 level year and the forward level year were 68.4, 72.5 and 74.3 % respectively, belonging to high alteration in all three level years. The runoff series of mainstream hydrological stations presented variability in different degrees, where the runoff series of the four hydrological stations including Xiangjiaba, Gaochang and Wulong belonged to high alteration in the three level years; and the runoff series of Beibei hydrological station in 2010 level year belonged to medium alteration, and high alteration in 2015 level year and the forward level year. The study on the impact of the operation of cascade reservoirs in Upper Yangtze River on hydrological variability of the mainstream had important practical significance on the sustainable utilization of water resources, disaster prevention and mitigation, safe and efficient operation and management of water conservancy projects and stable development of the economic society.

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

30 CFR 57.22204 - Main fan operation and inspection (I-A, II-A, III, and V-A mines).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Main fan operation and inspection (I-A, II-A, III, and V-A mines). 57.22204 Section 57.22204 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... Main fan operation and inspection (I-A, II-A, III, and V-A mines). Main fans shall be— (a) Provided...

Design of experiments applications in bioprocessing: concepts and approach.

PubMed

Kumar, Vijesh; Bhalla, Akriti; Rathore, Anurag S

2014-01-01

Most biotechnology unit operations are complex in nature with numerous process variables, feed material attributes, and raw material attributes that can have significant impact on the performance of the process. Design of experiments (DOE)-based approach offers a solution to this conundrum and allows for an efficient estimation of the main effects and the interactions with minimal number of experiments. Numerous publications illustrate application of DOE towards development of different bioprocessing unit operations. However, a systematic approach for evaluation of the different DOE designs and for choosing the optimal design for a given application has not been published yet. Through this work we have compared the I-optimal and D-optimal designs to the commonly used central composite and Box-Behnken designs for bioprocess applications. A systematic methodology is proposed for construction of the model and for precise prediction of the responses for the three case studies involving some of the commonly used unit operations in downstream processing. Use of Akaike information criterion for model selection has been examined and found to be suitable for the applications under consideration. © 2013 American Institute of Chemical Engineers.

Radiation effect on rocket engine performance

NASA Technical Reports Server (NTRS)

Chiu, Huei-Huang

1988-01-01

The effects of radiation on the performance of modern rocket propulsion systems operating at high pressure and temperature were recognized as a key issue in the design and operation of various liquid rocket engines of the current and future generations. Critical problem areas of radiation coupled with combustion of bipropellants are assessed and accounted for in the formulation of a universal scaling law incorporated with a radiation-enhanced vaporization combustion model. Numerical algorithms are developed and the pertaining data of the Variable Thrust Engine (VTE) and Space Shuttle Main Engine (SSME) are used to conduct parametric sensitivity studies to predict the principal intercoupling effects of radiation. The analysis reveals that low enthalpy engines, such as the VTE, are vulnerable to a substantial performance set back by the radiative loss, whereas the performance of high enthalpy engines such as the SSME, are hardly affected over a broad range of engine operation. Additionally, combustion enhancement by the radiative heating of the propellant has a significant impact in those propellants with high absorptivity. Finally, the areas of research related with radiation phenomena in bipropellant engines are identified.

A biometeorological procedure for weather forecast to assess the optimal outdoor clothing insulation.

PubMed

Morabito, Marco; Crisci, Alfonso; Cecchi, Lorenzo; Modesti, Pietro Amedeo; Maracchi, Giampiero; Gensini, Gian Franco; Orlandini, Simone

2008-09-01

Clothing insulation represents an important parameter strongly dependent on climate/weather variability and directly involved in the assessment of the human energy balance. Few studies tried to explore the influence of climate changes on the optimal clothing insulation for outdoor spaces. For this reason, the aim of this work was to investigate mainly the optimal outdoor minimum clothing insulation value required to reach the thermal neutrality (min_clo) related to climate change on a seasonal basis. Subsequently, we developed an example of operational biometeorological procedure to provide 72-hour forecast maps concerning the min_clo. Hourly meteorological data were provided by three Italian weather stations located in Turin, Rome and Palermo, for the period 1951-1995. Environmental variables and subjective characteristics referred to an average adult young male at rest and at a very high metabolic rate were used as input variables to calculate the min_clo by using a thermal index based on the human energy balance. Trends of min_clo were assessed by a non-parametric statistical method. Results showed a lower magnitude of trends in a subject at a very high metabolic rate than at rest. Turin always showed a decrease of min_clo during the study period and prevalently negative trends were also observed in Palermo. On the other hand, an opposite situation was observed in Rome, especially during the morning in all seasons. The development of a daily operational procedure to forecast customized min_clo could provide useful information for the outdoor clothing fitting that might help to reduce the weather-related human health risk.

Identification of the Critical Nontechnical Skills for Surgeons Needed for High Performance in a Variable-resource Context (NOTSS-VRC).

PubMed

Scott, John W; Lin, Yihan; Ntakiyiruta, Georges; Mutabazi, Zeta; Davis, William A; Morris, Megan A; Smink, Douglas S; Riviello, Robert; Yule, Steven

2018-05-17

To identify the critical nontechnical skills (NTS) required for high performance in variable-resource contexts (VRC). As surgical training and capacity increase in low- and middle-income countries (LMICs), new strategies for improving surgical education and care in these settings are required. NTS are critical for high performance in surgery around the world. However, the essential NTS used by surgeons operating in LMICs to overcome the challenges specific to their contexts have never been described. Using a constructivist grounded theory approach, 52 intraoperative team observations as well as 34 critical incident interviews with surgical providers (surgeons, anesthetists, and nurses) were performed at the 4 tertiary referral hospitals in Rwanda. Interview transcripts and field notes from observations were analyzed using line-by-line coding to identify emerging themes until thematic saturation was achieved. Four skill categories of situation awareness, decision-making, communication/teamwork, and leadership emerged. This provided the framework for a contextually informed skills taxonomy consisting of 12 skill elements with examples of specific behaviors indicative of high performance. While the main skill categories were consistent with those encountered in high-income countries, the specific behaviors associated with these skills often focused on overcoming the frequently encountered variability in resources, staff, systems support, and language in this context. This is the first description of the critical nontechnical skills, and associated example behaviors, used by surgeons in a VRC to overcome common challenges to safe and effective surgical patient care. Improvements in the NTS used by surgeons operating in VRCs have the potential to improve surgical care delivery worldwide.

Oscillations and trends of river discharge in the southern Central Andes and linkages with climate variability

NASA Astrophysics Data System (ADS)

Castino, Fabiana; Bookhagen, Bodo; Strecker, Manfred R.

2017-12-01

This study analyzes the discharge variability of small to medium drainage basins (102-104 km2) in the southern Central Andes of NW Argentina. The Hilbert-Huang Transform (HHT) was applied to evaluate non-stationary oscillatory modes of variability and trends, based on four time series of monthly-normalized discharge anomaly between 1940 and 2015. Statistically significant trends reveal increasing discharge during the past decades and document an intensification of the hydrological cycle during this period. An Ensemble Empirical Mode Decomposition (EEMD) analysis revealed that discharge variability in this region can be best described by five quasi-periodic statistically significant oscillatory modes, with mean periods varying from 1 to ∼20 y. Moreover, we show that discharge variability is most likely linked to the phases of the Pacific Decadal Oscillation (PDO) at multi-decadal timescales (∼20 y) and, to a lesser degree, to the Tropical South Atlantic SST anomaly (TSA) variability at shorter timescales (∼2-5 y). Previous studies highlighted a rapid increase in discharge in the southern Central Andes during the 1970s, inferred to have been associated with the global 1976-77 climate shift. Our results suggest that the rapid discharge increase in the NW Argentine Andes coincides with the periodic enhancement of discharge, which is mainly linked to a negative to positive transition of the PDO phase and TSA variability associated with a long-term increasing trend. We therefore suggest that variations in discharge in this region are largely driven by both natural variability and the effects of global climate change. We furthermore posit that the links between atmospheric and hydrologic processes result from a combination of forcings that operate on different spatiotemporal scales.

Predictors of Post-Operative Pain Relief in Patients with Chronic Pancreatitis Undergoing the Frey or Whipple Procedure.

PubMed

Sinha, Amitasha; Patel, Yuval A; Cruise, Michael; Matsukuma, Karen; Zaheer, Atif; Afghani, Elham; Yadav, Dhiraj; Makary, Martin A; Hirose, Kenzo; Andersen, Dana K; Singh, Vikesh K

2016-04-01

Post-operative pain relief in chronic pancreatitis (CP) is variable. Our objective was to determine clinical imaging or histopathologic predictor(s) of post-operative pain relief in CP patients undergoing the Whipple or Frey procedure. All patients who underwent a Whipple (n = 30) or Frey procedure (n = 30) for painful CP between January 2003 and September 2013 were evaluated. A toxic etiology was defined as a history of alcohol use and/or smoking. The pre-operative abdominal CT was evaluated for calcification(s) and main pancreatic duct (MPD) dilation (≥5 mm). The post-operative histopathology was evaluated for severe fibrosis. Clinical imaging and histopathologic features were evaluated as predictors of post-operative pain relief using univariable and multivariable regression analysis. A total of 60 patients (age 51.6 years, 53% males) were included in our study, of whom 42 (70%) reported post-operative pain relief over a mean follow-up of 1.1 years. There were 37 (62%) patients with toxic etiology, 36 (60%) each with calcification(s) and MPD dilation. A toxic etiology, calcifications, and severe fibrosis were associated with post-operative pain relief on univariable analysis (all p < 0.01). However, only a toxic etiology was an independent predictor of post-operative pain relief (OR 5.7, 95% CI 1.3, 24.5, p = 0.02). Only a toxic etiology, and not imaging or histopathologic findings, independently predicts post-operative pain relief in CP patients undergoing the Whipple or Frey procedure.

40 CFR 63.1207 - What are the performance testing requirements?

Code of Federal Regulations, 2010 CFR

2010-07-01

... operating conditions that are most likely to reflect daily maximum operating variability, similar to a... operating variability, similar to a dioxin/furan compliance test; (B) You have not changed the design or... document the temperature location measurement in the comprehensive performance test plan, as required by...

NOVEL CRYOGENIC ENGINEERING SOLUTIONS FOR THE NEW AUSTRALIAN RESEARCH REACTOR OPAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olsen, S. R.; Kennedy, S. J.; Kim, S.

In August 2006 the new 20MW low enriched uranium research reactor OPAL went critical. The reactor has 3 main functions, radio pharmaceutical production, silicon irradiation and as a neutron source. Commissioning on 7 neutron scattering instruments began in December 2006. Three of these instruments (Small Angle Neutron Scattering, Reflectometer and Time-of-flight Spectrometer) utilize cold neutrons.The OPAL Cold Neutron Source, located inside the reactor, is a 20L liquid deuterium moderated source operating at 20K, 330kPa with a nominal refrigeration capacity of 5 kW and a peak flux at 4.2meV (equivalent to a wavelength of 0.4nm). The Thermosiphon and Moderator Chamber aremore » cooled by helium gas delivered at 19.8K using the Brayton cycle. The helium is compressed by two 250kW compressors (one with a variable frequency drive to lower power consumption).A 5 Tesla BSCCO (2223) horizontal field HTS magnet will be delivered in the 2{sup nd} half of 2007 for use on all the cold neutron instruments. The magnet is cooled by a pulse tube cryocooler operating at 20K. The magnet design allows for the neutron beam to pass both axially and transverse to the field. Samples will be mounted in a 4K to 800K Gifford-McMahon (GM) cryofurnace, with the ability to apply a variable electric field in-situ. The magnet is mounted onto a tilt stage. The sample can thus be studied under a wide variety of conditions.A cryogen free 7.4 Tesla Nb-Ti vertical field LTS magnet, commissioned in 2005 will be used on neutron diffraction experiments. It is cooled by a standard GM cryocooler operating at 4.2K. The sample is mounted in a 2{sup nd} GM cryocooler (4K-300K) and a variable electric field can be applied.« less

Risk factors of prolonged mechanical ventilation following open heart surgery: what has changed over the last decade?

PubMed

Siddiqui, Muhammad-Mujtaba Ali; Paras, Iftikhar; Jalal, Anjum

2012-09-01

To identify the risk factors for prolonged invasive mechanical ventilation after open heart surgery in Pakistan. This study is based on retrospective analysis of database. We conducted study of all patients who underwent open heart surgery at CPE Institute of Cardiology, Multan from March 2009 to May 2011. The data was retrieved from the database in the form of electronic spreadsheet which was then analyzed using SPSS software. The patients with incomplete data entries were removed from the analysis resulting in a set of 1,617 patients. The data of each patient consisted of 65 preoperative, operative and postoperative variables. The data was summarized as means, medians and standard deviations for numeric variables and frequencies and percentages or categoric variables. These risk factors were compared using Chi-sqaure test. Their ODDs ratios and 95% confidence intervals of ODD's Ratios and P values were calculated. Out of a total of 1,617 patients, 77 patients (4.76%) had prolonged ventilation for a cumulated duration of more than over 24 hours. Preoperative renal failure, emphysema, low EF (<30%), urgent operation, preoperative critical state, prolonged bypass time, prolonged cross clamp time, complex surgical procedures and peri-operative myocardial infarction were found to be risk factors for PIMV. Old age, female gender, advanced ASA class, advanced NYHA class, diabetes mellitus, smoking, history of COPD, redo surgery, left main stenosis, obesity and use of intra-aortic balloon pump were not found to have significant ODDs ratios for PIMV. The patients with prolonged ventilation had significantly high mortality i.e. 32.47% while the normal ventilation group had 0.32% overall mortality. Many of the previously considered risk factors for prolonged ventilation after open heart study are no more significant risk factors. However, prolonged ventilation continues to be associated with very high mortality.

Improving fire season definition by optimized temporal modelling of daily human-caused ignitions.

PubMed

Costafreda-Aumedes, S; Vega-Garcia, C; Comas, C

2018-07-01

Wildfire suppression management is usually based on fast control of all ignitions, especially in highly populated countries with pervasive values-at-risk. To minimize values-at-risk loss by improving response time of suppression resources it is necessary to anticipate ignitions, which are mainly caused by people. Previous studies have found that human-ignition patterns change spatially and temporally depending on socio-economic activities, hence, the deployment of suppression resources along the year should consider these patterns. However, full suppression capacity is operational only within legally established fire seasons, driven by past events and budgets, which limits response capacity and increases damages out of them. The aim of this study was to assess the temporal definition of fire seasons from the perspective of human-ignition patterns for the case study of Spain, where people cause over 95% of fires. Humans engage in activities that use fire as a tool in certain periods within a year, and in locations linked to specific spatial factors. Geographic variables (population, infrastructures, physiography and land uses) were used as explanatory variables for human-ignition patterns. The changing influence of these geographic variables on occurrence along the year was analysed with day-by-day logistic regression models. Daily models were built for all the municipal units in the two climatic regions in Spain (Atlantic and Mediterranean Spain) from 2002 to 2014, and similar models were grouped within continuous periods, designated as ignition-based seasons. We found three ignition-based seasons in the Mediterranean region and five in the Atlantic zones, not coincidental with calendar seasons, but with a high degree of agreement with current legally designated operational fire seasons. Our results suggest that an additional late-winter-early-spring fire season in the Mediterranean area and the extension of this same season in the Atlantic zone should be re-considered for operational purposes in the future. Copyright © 2018 Elsevier Ltd. All rights reserved.

Variability in hand-arm vibration during grinding operations.

PubMed

Liljelind, Ingrid; Wahlström, Jens; Nilsson, Leif; Toomingas, Allan; Burström, Lage

2011-04-01

Measurements of exposure to vibrations from hand-held tools are often conducted on a single occasion. However, repeated measurements may be crucial for estimating the actual dose with good precision. In addition, knowledge of determinants of exposure could be used to improve working conditions. The aim of this study was to assess hand-arm vibration (HAV) exposure during different grinding operations, in order to obtain estimates of the variance components and to evaluate the effect of work postures. Ten experienced operators used two compressed air-driven angle grinders of the same make in a simulated work task at a workplace. One part of the study consisted of using a grinder while assuming two different working postures: at a standard work bench (low) and on a wall with arms elevated and the work area adjusted to each operator's height (high). The workers repeated the task three times. In another part of the study, investigating the wheel wear, for each grinder, the operators used two new grinding wheels and with each wheel the operator performed two consecutive 1-min grinding tasks. Both grinding tasks were conducted on weld puddles of mild steel on a piece of mild steel. Measurements were taken according to ISO-standard 5349 [the equivalent hand-arm-weighted acceleration (m s(-2)) averaged over 1 min]. Mixed- and random-effects models were used to investigate the influence of the fixed variables and to estimate variance components. The equivalent hand-arm-weighted acceleration assessed when the task was performed on the bench and at the wall was 3.2 and 3.3 m s(-2), respectively. In the mixed-effects model, work posture was not a significant variable. The variables 'operator' and 'grinder' together explained only 12% of the exposure variability and 'grinding wheel' explained 47%; the residual variability of 41% remained unexplained. When the effect of grinding wheel wear was investigated in the random-effects model, 37% of the variability was associated with the wheel while minimal variability was associated with the operator or the grinder and 37% was unexplained. The interaction effect of grinder and operator explained 18% of the variability. In the wheel wear test, the equivalent hand-arm-weighted accelerations for Grinder 1 during the first and second grinding minutes were 3.4 and 2.9 m s(-2), respectively, and for Grinder 2, they were 3.1 and 2.9 m s(-2), respectively. For Grinder 1, the equivalent hand-arm-weighted acceleration during the first grinding minute was significantly higher (P = 0.04) than during the second minute. Work posture during grinding operations does not appear to affect the level of HAV. Grinding wheels explained much of the variability in this study, but almost 40% of the variance remained unexplained. The considerable variability in the equivalent hand-arm-weighted acceleration has an impact on the risk assessment at both the group and the individual level.

Associations between pre-operative radiographic changes and outcomes after total knee joint replacement for osteoarthritis.

PubMed

Dowsey, M M; Nikpour, M; Dieppe, P; Choong, P F M

2012-10-01

To assess the influence of pre-operative X-ray changes on the response to total knee joint replacement (TKR). We included patients from one centre who underwent primary TKR (n = 478) for osteoarthritis in 2006 and 2007. The International Knee Society score (IKSS) and short form health survey were collected pre-operatively and at 1 and 2 years after surgery. Pre-operative radiographs were read to assess Kellgren and Lawrence (K-L) grading, individual radiographic features using the OARSI atlas, and subchondral bone attrition using the Ahlbach method. The main independent variable was a modified (K-L) grade. The outcome variables were the IKSS pain and function scores. Covariates included demographic features, co-morbidities, baseline pain and function, prosthesis type, and the use of patella resurfacing. Multivariable linear regression models were created to assess the relationships between pre-operative X-ray findings and pain and function outcomes. On average, pain and function improved greatly following surgery. However, pain relief was unsatisfactory in about 30%, and functional improvement suboptimal in about 50%. OR (95% CI) for ongoing moderate-severe pain at 12 months for modified K-L grades; <3: 5.39 (1.23-15.69), 3a: 2.62 (1.21-5.67), 3b: 1.81 (1.00-3.26), 4a: 2.06 (1.05-4.05) when compared to 4b. OR (95% CI) for poor function at 12 months were; 3a: 2.81 (1.23-6.39) and 4a: 2.45 (1.22-4.91), when compared to 4b. Patients with more severe radiographic knee damage at the time of surgery are most likely to have substantial gains in terms of both pain relief and improved function as a result of a TKR. Copyright © 2012 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Power partial-discard strategy to obtain improved performance for simulated moving bed chromatography.

PubMed

Chung, Ji-Woo; Kim, Kyung-Min; Yoon, Tae-Ung; Kim, Seung-Ik; Jung, Tae-Sung; Han, Sang-Sup; Bae, Youn-Sang

2017-12-22

A novel power partial-discard (PPD) strategy was developed as a variant of the partial-discard (PD) operation to further improve the separation performance of the simulated moving bed (SMB) process. The PPD operation varied the flow rates of discard streams by introducing a new variable, the discard amount (DA) as well as varying the reported variable, discard length (DL), while the conventional PD used fixed discard flow rates. The PPD operations showed significantly improved purities in spite of losses in recoveries. Remarkably, the PPD operation could provide more enhanced purity for a given recovery or more enhanced recovery for a given purity than the PD operation. The two variables, DA and DL, in the PPD operation played a key role in achieving the desired purity and recovery. The PPD operations will be useful for attaining high-purity products with reasonable recoveries. Copyright © 2017 Elsevier B.V. All rights reserved.

Operational Impacts of Operating Reserve Demand Curves on Production Cost and Reliability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind, solar, electric vehicles, and energy storage systems become more cost-effective and present in the system, traditional power system operating strategies will need to be reevaluated. The presence of wind and solar generation (commonly referred to as variable generation) may result in an increase in the variability and uncertainty of the net load profile. One mechanism to mitigate this is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increasedmore » variability and uncertainty occurring at finer temporal resolutions. A new operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this paper, and its implications on power system operations are analyzed.« less

Operational Impacts of Operating Reserve Demand Curves on Production Cost and Reliability: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind, solar, electric vehicles, and energy storage systems become more cost-effective and present in the system, traditional power system operating strategies will need to be reevaluated. The presence of wind and solar generation (commonly referred to as variable generation) may result in an increase in the variability and uncertainty of the net load profile. One mechanism to mitigate this is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increasedmore » variability and uncertainty occurring at finer temporal resolutions. A new operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this paper, and its implications on power system operations are analyzed.« less

The complete Einstein Observatory X-ray survey of the Orion Nebula region.

NASA Technical Reports Server (NTRS)

Gagne, Marc; Caillault, Jean-Pierre

1994-01-01

We have analyzed archival Einstein Observatory images of a roughly 4.5 square degree region centered on the Orion Nebula. In all, 245 distinct X-ray sources have been detected in six High Resolution Imager (HRI) and 17 Imaging Proportional Counter (IPC) observations. An optical database of over 2700 stars has been assembled to search for candidate counterparts to the X-ray sources. Roughly half the X-ray sources are identified with a single Orion Nebula cluster member. The 10 main-sequence O6-B5 cluster stars detected in Orion have X-ray activity levels comparable to field O and B stars. X-ray emission has also been detected in the direction of four main-sequence late-B and early-A type stars. Since the mechanisms producing X-rays in late-type coronae and early-type winds cannot operate in the late-B and early-A type atmospheres, we argue that the observed X-rays, with L(sub X) approximately = 3 x 10(exp 30) ergs/s, are probably produced in the coronae of unseen late-type binary companions. Over 100 X-ray sources have been associated with late-type pre-main sequence stars. The upper envelope of X-ray activity rises sharply from mid-F to late-G, with L(sub x)/L(sub bol) in the range 10(exp -4) to 2 x 10(exp -3) for stars later than approximately G7. We have looked for variability of the late-type cluster members on timescales of a day to a year and find that 1/4 of the stars show significantly variable X-ray emission. A handful of the late-type stars have published rotational periods and spectroscopic rotational velocities; however, we see no correlation between X-ray activity and rotation. Thus, for this sample of pre-main-sequence stars, the large dispersion in X-ray activity does not appear to be caused by the dispersion in rotation, in contrast with results obtained for low-mass main-sequence stars in the Pleiades and pre-main-sequence stars in Taurus-Auriga.

49 CFR 218.105 - Additional operational requirements for hand-operated main track switches.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Additional operational requirements for hand... hand-operated main track switches. (a) Each railroad shall adopt and comply with an operating rule... the requirements of this section. (b) Designating switch position. The normal position of a hand...

A QC approach to the determination of day-to-day reproducibility and robustness of LC-MS methods for global metabolite profiling in metabonomics/metabolomics.

PubMed

Gika, Helen G; Theodoridis, Georgios A; Earll, Mark; Wilson, Ian D

2012-09-01

An approach to the determination of day-to-day analytical robustness of LC-MS-based methods for global metabolic profiling using a pooled QC sample is presented for the evaluation of metabonomic/metabolomic data. A set of 60 urine samples were repeatedly analyzed on five different days and the day-to-day reproducibility of the data obtained was determined. Multivariate statistical analysis was performed with the aim of evaluating variability and selected peaks were assessed and validated in terms of retention time stability, mass accuracy and intensity. The methodology enables the repeatability/reproducibility of extended analytical runs in large-scale studies to be determined, allowing the elimination of analytical (as opposed to biological) variability, in order to discover true patterns and correlations within the data. The day-to-day variability of the data revealed by this process suggested that, for this particular system, 3 days continuous operation was possible without the need for maintenance and cleaning. Variation was generally based on signal intensity changes over the 7-day period of the study, and was mainly a result of source contamination.

Streamflow variability and optimal capacity of run-of-river hydropower plants

NASA Astrophysics Data System (ADS)

Basso, S.; Botter, G.

2012-10-01

The identification of the capacity of a run-of-river plant which allows for the optimal utilization of the available water resources is a challenging task, mainly because of the inherent temporal variability of river flows. This paper proposes an analytical framework to describe the energy production and the economic profitability of small run-of-river power plants on the basis of the underlying streamflow regime. We provide analytical expressions for the capacity which maximize the produced energy as a function of the underlying flow duration curve and minimum environmental flow requirements downstream of the plant intake. Similar analytical expressions are derived for the capacity which maximize the economic return deriving from construction and operation of a new plant. The analytical approach is applied to a minihydro plant recently proposed in a small Alpine catchment in northeastern Italy, evidencing the potential of the method as a flexible and simple design tool for practical application. The analytical model provides useful insight on the major hydrologic and economic controls (e.g., streamflow variability, energy price, costs) on the optimal plant capacity and helps in identifying policy strategies to reduce the current gap between the economic and energy optimizations of run-of-river plants.

Demographic Variables of Corruption in the Chinese Construction Industry: Association Rule Analysis of Conviction Records.

PubMed

Yu, Yao; Martek, Igor; Hosseini, M Reza; Chen, Chuan

2018-05-02

Corruption in the construction industry is a serious problem in China. As such, fighting this corruption has become a priority target of the Chinese government, with the main effort being to discover and prosecute its perpetrators. This study profiles the demographic characteristics of major incidences of corruption in construction. It draws on the database of the 83 complete recorded cases of construction related corruption held by the Chinese National Bureau of Corruption Prevention. Categorical variables were drawn from the database, and 'association rule mining analysis' was used to identify associations between variables as a means of profiling perpetrators. Such profiling may be used as predictors of future incidences of corruption, and consequently to inform policy makers in their fight against corruption. The results signal corruption within the Chinese construction industry to be correlated with age, with incidences rising as managers' approach retirement age. Moreover, a majority of perpetrators operate within government agencies, are department deputies in direct contact with projects, and extort the greatest amounts per case from second tier cities. The relatively lengthy average 6.4-year period before cases come to public attention corroborates the view that current efforts at fighting corruption remain inadequate.

Determining the effect of key climate drivers on global hydropower production

NASA Astrophysics Data System (ADS)

Galelli, S.; Ng, J. Y.; Lee, D.; Block, P. J.

2017-12-01

Accounting for about 17% of total global electrical power production, hydropower is arguably the world's main renewable energy source and a key asset to meet Paris climate agreements. A key component of hydropower production is water availability, which depends on both precipitation and multiple drivers of climate variability acting at different spatial and temporal scales. To understand how these drivers impact global hydropower production, we study the relation between four patterns of ocean-atmosphere climate variability (i.e., El Niño Southern Oscillation, Pacific Decadal Oscillation, North Atlantic Oscillation, and Atlantic Multidecadal Oscillation) and monthly time series of electrical power production for over 1,500 hydropower reservoirs—obtained via simulation with a high-fidelity dam model forced with 20th century climate conditions. Notably significant relationships between electrical power productions and climate variability are found in many climate sensitive regions globally, including North and South America, East Asia, West Africa, and Europe. Coupled interactions from multiple, simultaneous climate drivers are also evaluated. Finally, we highlight the importance of using these climate drivers as an additional source of information within reservoir operating rules where the skillful predictability of inflow exists.

Development of a Patient-Based Model for Estimating Operative Times for Robot-Assisted Radical Prostatectomy.

PubMed

Huben, Neil; Hussein, Ahmed; May, Paul; Whittum, Michelle; Kraswowki, Collin; Ahmed, Youssef; Jing, Zhe; Khan, Hijab; Kim, Hyung; Schwaab, Thomas; Underwood Iii, Willie; Kauffman, Eric; Mohler, James L; Guru, Khurshid A

2018-04-10

To develop a methodology for predicting operative times for robot-assisted radical prostatectomy (RARP) using preoperative patient, disease, procedural and surgeon variables to facilitate operating room (OR) scheduling. The model included preoperative metrics: BMI, ASA score, clinical stage, National Comprehensive Cancer Network (NCCN) risk, prostate weight, nerve-sparing status, extent and laterality of lymph node dissection, and operating surgeon (6 surgeons were included in the study). A binary decision tree was fit using a conditional inference tree method to predict operative times. The variables most associated with operative time were determined using permutation tests. The data was split at the value of the variable that results in the largest difference in means for surgical time across the split. This process was repeated recursively on the resultant data. 1709 RARPs were included. The variable most strongly associated with operative time was the surgeon (surgeons 2 and 4 - 102 minutes shorter than surgeons 1, 3, 5, and 6, p<0.001). Among surgeons 2 and 4, BMI had the strongest association with surgical time (p<0.001). Among patients operated by surgeons 1, 3, 5 and 6, RARP time was again most strongly associated with the surgeon performing RARP. Surgeons 1, 3, and 6 were on average 76 minutes faster than surgeon 5 (p<0.001). The regression tree output in the form of box plots showed operative time median and ranges according to patient, disease, procedural and surgeon metrics. We developed a methodology that can predict operative times for RARP based on patient, disease and surgeon variables. This methodology can be utilized for quality control, facilitate OR scheduling and maximize OR efficiency.

33 CFR 157.168 - Crew member: Main deck watch.

Code of Federal Regulations, 2010 CFR

2010-07-01

... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.168 Crew member: Main deck watch. During COW operations, the master shall ensure that at least one member of the crew with a designated responsibility for monitoring COW operations is on the main deck at all times. ...

Multiple and variable speed electrical generator systems for large wind turbines

NASA Technical Reports Server (NTRS)

Andersen, T. S.; Hughes, P. S.; Kirschbaum, H. S.; Mutone, G. A.

1982-01-01

A cost effective method to achieve increased wind turbine generator energy conversion and other operational benefits through variable speed operation is presented. Earlier studies of multiple and variable speed generators in wind turbines were extended for evaluation in the context of a specific large sized conceptual design. System design and simulation have defined the costs and performance benefits which can be expected from both two speed and variable speed configurations.

Intraindividual change and variability in daily stress processes: Findings from two measurement-burst diary studies

PubMed Central

Sliwinski, Martin J.; Almeida, David M.; Smyth, Joshua; Stawski, Robert S.

2010-01-01

There is little longitudinal information on aging-related changes in emotional responses to negative events. The present manuscript examined intraindividual change and variability in the within-person coupling of daily stress and negative affect (NA) using data from two-measurement burst daily diary studies. Three main findings emerged. First, average reactivity to daily stress increased longitudinally, and this increase was evident across most the adult lifespan. Second, individual differences in emotional reactivity to daily stress exhibited long-term temporal stability, but this stability was greatest in midlife and decreased in old age. And third, reactivity to daily stress varied reliably within-persons (across-time), with individual exhibiting higher levels of reactivity during times when reporting high levels of global subject stress in previous month. Taken together, the present results emphasize the importance of modeling dynamic psychosocial and aging processes that operate across different time scales for understanding age-related changes in daily stress processes. PMID:20025399

The Policy Formation Process: A Conceptual Framework for Analysis. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Fuchs, E. F.

1972-01-01

A conceptual framework for analysis which is intended to assist both the policy analyst and the policy researcher in their empirical investigations into policy phenomena is developed. It is meant to facilitate understanding of the policy formation process by focusing attention on the basic forces shaping the main features of policy formation as a dynamic social-political-organizational process. The primary contribution of the framework lies in its capability to suggest useful ways of looking at policy formation reality. It provides the analyst and the researcher with a group of indicators which suggest where to look and what to look for when attempting to analyze and understand the mix of forces which energize, maintain, and direct the operation of strategic level policy systems. The framework also highlights interconnections, linkage, and relational patterns between and among important variables. The framework offers an integrated set of conceptual tools which facilitate understanding of and research on the complex and dynamic set of variables which interact in any major strategic level policy formation process.

Method for assessing motor insulation on operating motors

DOEpatents

Kueck, John D.; Otaduy, Pedro J.

1997-01-01

A method for monitoring the condition of electrical-motor-driven devices. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques.

Structural Degradation of the Welded Joint of the Gas Main after a Long-Term Operation in Sub-Acid Soil

NASA Astrophysics Data System (ADS)

Maruschak, P. O.; Bishchak, R. T.; Maruschak, O. V.; Panin, S. V.

2018-01-01

The authors investigated the main regularities in the structural and mechanical degradation of steel and a welded joint of the “Soyuz” gas main in operation. It is established that the defect accumulation kinetics in welds are determined both by technological disruptions in their manufacture and by hydrogenation of the weld during a long operating time. A weakening of the mechanical properties of the weld after a prolonged operation is shown, which in some cases led to the appearance of cracks and fracture of the gas main.

Un formalisme de systemes a sauts pour la recirculation optimale des casses dans une machine a papier

NASA Astrophysics Data System (ADS)

Khanbaghi, Maryam

Increasing closure of white water circuits is making mill productivity and quality of paper produced increasingly affected by the occurrence of paper breaks. In this thesis the main objective is the development of white water and broke recirculation policies. The thesis consists of three main parts, respectively corresponding to the synthesis of a statistical model of paper breaks in a paper mill, the basic mathematical setup for the formulation of white water and broke recirculation policies in the mill as a jump linear quadratic regulation problem, and finally the tuning of the control law based on first passage-time theory, and its extension to the case of control sensitive paper break rates. More specifically, in the first part a statistical model of paper machine breaks is developed. We start from the hypothesis that the breaks process is a Markov chain with three states: the first state is the operational one, while the two others are associated with the general types of paper-breaks that can take place in the mill (wet breaks and dry breaks). The Markovian hypothesis is empirically validated. We also establish how paper-break rates are correlated with machine speed and broke recirculation ratio. Subsequently, we show how the obtained Markov chain model of paper-breaks can be used to formulate a machine operating speed parameter optimization problem. In the second part, upon recognizing that paper breaks can be modelled as a Markov chain type of process which, when interacting with the continuous mill dynamics, yields a jump Markov model, jump linear theory is proposed as a means of constructing white water and broke recirculation strategies which minimize process variability. Reduced process variability comes at the expense of relatively large swings in white water and broke tanks level. Since the linear design does not specifically account for constraints on the state-space, under the resulting law, damaging events of tank overflow or emptiness can occur. A heuristic simulation-based approach is proposed to choose the performance measure design parameters to keep the mean time between incidents of fluid in broke and white water tanks either overflowing, or reaching dangerously low levels, sufficiently long. In the third part, a methodology, mainly founded on the first passage-time theory of stochastic processes, is proposed to choose the performance measure design parameters to limit process variability while accounting for the possibility of undesirable tank overflows or tank emptiness. The heart of the approach is an approximation technique for evaluating mean first passage-times of the controlled tanks levels. This technique appears to have an applicability which largely exceeds the problem area it was designed for. Furthermore, the introduction of control sensitive break rates and the analysis of the ensuing control problem are presented. This is to account for the experimentally observed increase in breaks concomitant with flow rate variability.

Designing basin-customized combined drought indices via feature extraction

NASA Astrophysics Data System (ADS)

Zaniolo, Marta; Giuliani, Matteo; Castelletti, Andrea

2017-04-01

The socio-economic costs of drought are progressively increasing worldwide due to the undergoing alteration of hydro-meteorological regimes induced by climate change. Although drought management is largely studied in the literature, most of the traditional drought indexes fail in detecting critical events in highly regulated systems, which generally rely on ad-hoc formulations and cannot be generalized to different context. In this study, we contribute a novel framework for the design of a basin-customized drought index. This index represents a surrogate of the state of the basin and is computed by combining the available information about the water available in the system to reproduce a representative target variable for the drought condition of the basin (e.g., water deficit). To select the relevant variables and how to combine them, we use an advanced feature extraction algorithm called Wrapper for Quasi Equally Informative Subset Selection (W-QEISS). The W-QEISS algorithm relies on a multi-objective evolutionary algorithm to find Pareto-efficient subsets of variables by maximizing the wrapper accuracy, minimizing the number of selected variables (cardinality) and optimizing relevance and redundancy of the subset. The accuracy objective is evaluated trough the calibration of a pre-defined model (i.e., an extreme learning machine) of the water deficit for each candidate subset of variables, with the index selected from the resulting solutions identifying a suitable compromise between accuracy, cardinality, relevance, and redundancy. The proposed methodology is tested in the case study of Lake Como in northern Italy, a regulated lake mainly operated for irrigation supply to four downstream agricultural districts. In the absence of an institutional drought monitoring system, we constructed the combined index using all the hydrological variables from the existing monitoring system as well as the most common drought indicators at multiple time aggregations. The soil moisture deficit in the root zone computed by a distributed-parameter water balance model of the agricultural districts is used as target variable. Numerical results show that our framework succeeds in constructing a combined drought index that reproduces the soil moisture deficit. Moreover, this index represents a valuable information for supporting appropriate drought management strategies, including the possibility of directly informing the lake operations about the drought conditions and improve the overall reliability of the irrigation supply system.

The Role of Structural Dynamics and Testing in the Shuttle Flowliner Crack Investigation

NASA Technical Reports Server (NTRS)

Frady, Gregory P.

2005-01-01

During a normal inspection of the main propulsion system at Kennedy Space Center, small cracks were noticed near a slotted region of a gimbal joint flowliner located just upstream from one of the Space Shuttle Main Engines (SSME). These small cracks sparked an investigation of the entire Space Shuttle fleet main propulsion feedlines. The investigation was initiated to determine the cause of the small cracks and a repair method that would be needed to return the Shuttle fleet back to operation safely. The cracks were found to be initiated by structural resonance caused by flow fluctuations from the SSME low pressure fuel turbopump interacting with the flowliner. The pump induced backward traveling wakes that excited the liner and duct acoustics which also caused the liner to vibrate in complex mode shapes. The investigation involved an extensive effort by a team of engineers from the NASA civil servant and contractor workforce with the goal to characterize the root cause of the cracking behavior of the fuel side gimbal joint flowliners. In addition to working to identify the root cause, a parallel path was taken to characterize the material properties and fatigue capabilities of the liner material such that the life of the liners could be ascertained. As the characterization of the material and the most probable cause matured, the combination of the two with pump speed restrictions provided a means to return the Shuttle to flight in a safe manner. This paper traces the flowliner investigation results with respect to the structural dynamics analysis, component level testing and hot-fire flow testing on a static testbed. The paper will address the unique aspects of a very complex problem involving backflow from a high performance pump that has never been characterized nor understood to such detail. In addition, the paper will briefly address the flow phenomena that excited the liners, the unique structural dynamic modal characteristics and the variability of SSME operation which has ultimately ensured the safe and reliable operation of the shuttle main engines for each flight.

Partial discharge detection and analysis in low pressure environments

NASA Astrophysics Data System (ADS)

Liu, Xin

Typical aerospace vehicles (aircraft and spacecraft) experience a wide range of operating pressures during ascending and returning to earth. Compared to the sea-level atmospheric pressure (760 Torr), the pressure at about 60 km altitude is 2 Torr. The performance of the electric power system components of the aerospace vehicles must remain reliable even under such sub-atmospheric operating conditions. It is well known that the dielectric strength of gaseous insulators, while the electrode arrangement remains unchanged, is pressure dependent. Therefore, characterization of the performance and behavior of the electrical insulation in flight vehicles in low-pressure environments is extremely important. Partial discharge testing is one of the practical methods for evaluating the integrity of electrical insulation in aerospace vehicles. This dissertation describes partial discharge (PD) measurements performed mainly with 60 Hz ac energization in air, argon and helium, for pressures between 2 and 760 Torr. Two main electrode arrangements were used. One was a needle-plane electrode arrangement with a Teflon insulating barrier. The other one was a twisted pair of insulated conductors taken from a standard aircraft wiring harness. The measurement results are presented in terms of typical PD current pulse waveforms and waveform analysis for both main electrode arrangements. The evaluation criteria are the waveform polarity, magnitude, shape, rise time, and phase angle (temporal location) relative to the source voltage. Two-variable histograms and statistical averages of the PD parameters are presented. The PD physical mechanisms are analyzed. For PD pattern recognition, both statistical methods (such as discharge parameter dot pattern representation, discharge parameter phase distribution, statistical operator calculations, and PD fingerprint development) and wavelet transform applications are investigated. The main conclusions of the dissertation include: (1) The PD current pulse waveforms are dependent on the pressure. (2) The rise time of the waveform is another effective PD current pulse characteristic indicator. (3) PD fingerprint patterns that are already available for atmospheric pressure (760 Torr) conditions are inadequate for the evaluation of PD pulses at low pressures. (4) Various wavelet transform techniques can be used effectively for PD pulse signal denoising purposes, and for PD pulse waveform transient feature recognition.

Data Applicability of Heritage and New Hardware For Launch Vehicle Reliability Models

NASA Technical Reports Server (NTRS)

Al Hassan, Mohammad; Novack, Steven

2015-01-01

Bayesian reliability requires the development of a prior distribution to represent degree of belief about the value of a parameter (such as a component's failure rate) before system specific data become available from testing or operations. Generic failure data are often provided in reliability databases as point estimates (mean or median). A component's failure rate is considered a random variable where all possible values are represented by a probability distribution. The applicability of the generic data source is a significant source of uncertainty that affects the spread of the distribution. This presentation discusses heuristic guidelines for quantifying uncertainty due to generic data applicability when developing prior distributions mainly from reliability predictions.

Guidelines for the operation of variable message signs on state highways

DOT National Transportation Integrated Search

2004-06-01

A variable message sign (VMS) is a traffic control device whose message can be changed manually, electrically, mechanically, or electromechanically to provide motorists with information about traffic congestion, traffic crashes, maintenance operation...

Functional Quality Criterion of Rock Handling Mechanization at Open-pit Mines

NASA Astrophysics Data System (ADS)

Voronov, Yuri; Voronov, Artyoni

2017-11-01

Overburden and mining operations at open-pit mines are performed mainly by powerful shovel-truck systems (STSs). One of the main problems of the STSs is a rather low level of their operating quality, mainly due to unjustified over-trucking. In this article, a functional criterion for assessing the qualify of the STS operation at open-pit mines is formulated, derived and analyzed. We introduce the rationale and general principles for the functional criterion formation, its general form, as well as variations for various STS structures: a mixed truck fleet and a homogeneous shovel fleet, a mixed shove! fleet and a homogeneous truck fleet, mixed truck and shovel fleets. The possibility of assessing the quality of the STS operation is of great importance for identifying the main directions for improving their operational performance and operating quality, optimizing the main performance indicators by the qualify criterion, and. as a result, for possible saving of material and technical resources for open-pit mining. Improvement of the quality of the STS operation also allows increasing the mining safety and decreasing the atmosphere pollution - by means of possible reducing of the number of the operating trucks.

Dexamethasone in head and neck cancer patients with microvascular reconstruction: No benefit, more complications.

PubMed

Kainulainen, S; Törnwall, J; Koivusalo, A M; Suominen, A L; Lassus, P

2017-02-01

Glucocorticoids are widely used in association with major surgery of the head and neck to improve postoperative rehabilitation, shorten intensive care unit and hospital stay, and reduce neck swelling. This study aimed to clarify whether peri- and postoperative use of dexamethasone in reconstructive head and neck cancer surgery is associated with any advantages or disadvantages. This prospective double-blind randomized controlled trial comprised 93 patients. A total dose of 60mg of dexamethasone was administered to 51 patients over three days peri- and postoperatively. The remaining 42 patients served as controls. The main primary outcome variables were neck swelling, length of intensive care unit and hospital stay, duration of intubation or tracheostomy, and delay to start of possible radiotherapy. Complications were also recorded. No statistical differences emerged between the two groups in any of the main primary outcome variables. However, there were more major complications, especially infections, needing secondary surgery within three weeks of the operation in patients receiving dexamethasone than in control patients (27% vs. 7%, p=0.012). The use of dexamethasone in oral cancer patients with microvascular reconstruction did not provide a benefit. More major complications, especially infections, occurred in patients receiving dexamethasone. Our data thus do not support the use of peri- and postoperative dexamethasone in oropharyngeal cancer patients undergoing microvascular reconstruction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Downscaling ocean conditions with application to the Gulf of Maine, Scotian Shelf and adjacent deep ocean

NASA Astrophysics Data System (ADS)

Katavouta, Anna; Thompson, Keith

2017-04-01

A high resolution regional model (1/36 degree) of the Gulf of Maine, Scotian Shelf and adjacent deep ocean (GoMSS) is developed to downscale ocean conditions from an existing global operational system. First, predictions from the regional GoMSS model in a one-way nesting set up are evaluated using observations from multiple sources including satellite-borne sensors of surface temperature and sea level, CTDs, Argo floats and moored current meters. It is shown that on the shelf, the regional model predicts more realistic fields than the global system because it has higher resolution and includes tides that are absent from the global system. However, in deep water the regional model misplaces deep ocean eddies and meanders associated with the Gulf Stream. This is because of unrealistic internally generated variability (associated with the one-way nesting set up) that leads to decoupling of the regional model from the global system in the deep water. To overcome this problem, the large scales (length scales > 90 km) of the regional model are spectrally nudged towards the global system fields. This leads to more realistic predictions off the shelf. Wavenumber spectra show that even though spectral nudging constrains the large scales, it does not suppress the variability on small scales; on the contrary, it favours the formation of eddies with length scales below the cut-off wavelength of the spectral nudging.

The experimental studies of operating modes of a diesel-generator set at variable speed

NASA Astrophysics Data System (ADS)

Obukhov, S. G.; Plotnikov, I. A.; Surkov, M. A.; Sumarokova, L. P.

2017-02-01

A diesel generator set working at variable speed to save fuel is studied. The results of experimental studies of the operating modes of an autonomous diesel generator set are presented. Areas for regulating operating modes are determined. It is demonstrated that the transfer of the diesel generator set to variable speed of the diesel engine makes it possible to improve the energy efficiency of the autonomous generator source, as well as the environmental and ergonomic performance of the equipment as compared with general industrial analogues.

Optimal Operation of Variable Speed Pumping System in China's Eastern Route Project of S-to-N Water Diversion Project

NASA Astrophysics Data System (ADS)

Cheng, Jilin; Zhang, Lihua; Zhang, Rentian; Gong, Yi; Zhu, Honggeng; Deng, Dongsheng; Feng, Xuesong; Qiu, Jinxian

2010-06-01

A dynamic planning model for optimizing operation of variable speed pumping system, aiming at minimum power consumption, was proposed to achieve economic operation. The No. 4 Jiangdu Pumping Station, a source pumping station in China's Eastern Route of South-to-North Water Diversion Project, is taken as a study case. Since the sump water level of Jiangdu Pumping Station is affected by the tide of Yangtze River, the daily-average heads of the pumping system varies yearly from 3.8m to 7.8m and the tide level difference in one day up to 1.2m. Comparisons of operation electricity cost between optimized variable speed and fixed speed operations of pumping system were made. When the full load operation mode is adopted, whether or not electricity prices in peak-valley periods are considered, the benefits of variable speed operation cannot compensate the energy consumption of the VFD. And when the pumping system operates in part load and the peak-valley electricity prices are considered, the pumping system should cease operation or lower its rotational speed in peak load hours since the electricity price are much higher, and to the contrary the pumping system should raise its rotational speed in valley load hours to pump more water. The computed results show that if the pumping system operates in 80% or 60% loads, the energy consumption cost of specified volume of water will save 14.01% and 26.69% averagely by means of optimal variable speed operation, and the investment on VFD will be paid back in 2 or 3 years. However, if the pumping system operates in 80% or 60% loads and the energy cost is calculated in non peak-valley electricity price, the repayment will be lengthened up to 18 years. In China's S-to-N Water Diversion Project, when the market operation and peak-valley electricity prices are taken into effect to supply water and regulate water levels in regulation reservoirs as Hongzehu Lake, Luomahu Lake, etc. the economic operation of water-diversion pumping stations will be vital, and the adoption of VFDs to achieve optimal operation may be a good choice.

Improving preparedness of farmers to Climate Variability: A case study of Vidarbha region of Maharashtra, India

NASA Astrophysics Data System (ADS)

Swami, D.; Parthasarathy, D.; Dave, P.

2016-12-01

A key objective of the ongoing research is to understand the risk and vulnerability of agriculture and farming communities with respect to multiple climate change attributes, particularly monsoon variability and hydrology such as ground water availability. Climate Variability has always been a feature affecting Indian agriculture but the nature and characteristics of this variability is not well understood. Indian monsoon patterns are highly variable and most of the studies focus on larger domain such as Central India or Western coast (Ghosh et al., 2009) but district level analysis is missing i.e. the linkage between agriculture and climate variables at finer scale has not been investigated comprehensively. For example, Eastern Vidarbha region in Maharashtra is considered as one of the most agriculturally sensitive region in India, where every year a large number of farmers commit suicide. The main reasons for large number of suicides are climate related stressors such as droughts, hail storms, and monsoon variability aggravated with poor socio-economic conditions. Present study has tried to explore the areas in Vidarbha region of Maharashtra where famers and crop productivity, specifically cotton, sorghum, is highly vulnerable to monsoon variability, hydrological and socio-economic variables which are further modelled to determine the maximal contributing factor towards crops and farmers' vulnerability. After analysis using primary and secondary data, it will aid in decision making regarding field operations such as time of sowing, harvesting and irrigation requirements by optimizing the cropping pattern with climatic, hydrological and socio-economic variables. It also suggests the adaptation strategies to farmers regarding different types of cropping and water harvesting practices, optimized dates and timings for harvesting, sowing, water and nutrient requirements of particular crops according to the specific region. Primarily along with secondary analysis captured here can be highly beneficial for the farmers and policy makers while formulating agricultural policies related to climate change.

Method for assessing motor insulation on operating motors

DOEpatents

Kueck, J.D.; Otaduy, P.J.

1997-03-18

A method for monitoring the condition of electrical-motor-driven devices is disclosed. The method is achieved by monitoring electrical variables associated with the functioning of an operating motor, applying these electrical variables to a three phase equivalent circuit and determining non-symmetrical faults in the operating motor based upon symmetrical components analysis techniques. 15 figs.

Variable density management in riparian reserves: lessons learned from an operational study in managed forests of western Oregon, USA.

Treesearch

Samuel Chan; Paul Anderson; John Cissel; Larry Lateen; Charley Thompson

2004-01-01

A large-scale operational study has been undertaken to investigate variable density management in conjunction with riparian buffers as a means to accelerate development of late-seral habitat, facilitate rare species management, and maintain riparian functions in 40-70 year-old headwater forests in western Oregon, USA. Upland variable retention treatments include...

Increasing Vocal Variability in Children with Autism Using a Lag Schedule of Reinforcement

ERIC Educational Resources Information Center

Esch, John W.; Esch, Barbara E.; Love, Jessa R.

2009-01-01

Variability has been demonstrated to be an operant dimension of behavior (Neuringer, 2002; Page & Neuringer, 1985). Recently, lag schedules have been used to demonstrate operant variability of verbal behavior in persons with a diagnosis of autism (e.g., Lee, McComas, & Jawor, 2002). The current study evaluated the effects of a Lag 1 schedule on…

Somatotype in high performance female netball players may influence player position and the incidence of lower limb and back injuries

PubMed Central

Hopper, Diana M

1997-01-01

Aims To investigate the relation between somatotype, performance characteristics, and the incidence of injury during the Australian Netball Championships. Method Two hundred and forty high performance netball players competed at the Australian Netball Championships in which 213 (89%) were measured using the Heath-Carter somatotype scale. During these championships, in conjunction with the injury assessments, data analysis included a three factor analysis of variance (level of competition, playing position, and injury) for the dependent somatoype variables (endomorphy, mesomorphy, and ectopmorphy), and the level of significance was set at 0.05. Results For the three dependent somatotype variables, there were no main effects between endomorphy, mesomorphy, and ectopmorphy and the incidence of injury. However, for the mesomorphy and ectomorphy variables, significant main effects for the playing position were found. No main effects existed between the somatotype variables and levels of competition. Conclusion The somatotype variables did not influence the incidence of injury, but mesomorphy and ectopmorphy did influence the different playing positions. PMID:9298552

33 CFR 157.168 - Crew member: Main deck watch.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.168 Crew member: Main... designated responsibility for monitoring COW operations is on the main deck at all times. ...

33 CFR 157.168 - Crew member: Main deck watch.

Code of Federal Regulations, 2014 CFR

2014-07-01

... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.168 Crew member: Main... designated responsibility for monitoring COW operations is on the main deck at all times. ...

33 CFR 157.168 - Crew member: Main deck watch.

Code of Federal Regulations, 2013 CFR

2013-07-01

... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.168 Crew member: Main... designated responsibility for monitoring COW operations is on the main deck at all times. ...

33 CFR 157.168 - Crew member: Main deck watch.

Code of Federal Regulations, 2012 CFR

2012-07-01

... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.168 Crew member: Main... designated responsibility for monitoring COW operations is on the main deck at all times. ...

Subwavelength grating enabled on-chip ultra-compact optical true time delay line

PubMed Central

Wang, Junjia; Ashrafi, Reza; Adams, Rhys; Glesk, Ivan; Gasulla, Ivana; Capmany, José; Chen, Lawrence R.

2016-01-01

An optical true time delay line (OTTDL) is a basic photonic building block that enables many microwave photonic and optical processing operations. The conventional design for an integrated OTTDL that is based on spatial diversity uses a length-variable waveguide array to create the optical time delays, which can introduce complexities in the integrated circuit design. Here we report the first ever demonstration of an integrated index-variable OTTDL that exploits spatial diversity in an equal length waveguide array. The approach uses subwavelength grating waveguides in silicon-on-insulator (SOI), which enables the realization of OTTDLs having a simple geometry and that occupy a compact chip area. Moreover, compared to conventional wavelength-variable delay lines with a few THz operation bandwidth, our index-variable OTTDL has an extremely broad operation bandwidth practically exceeding several tens of THz, which supports operation for various input optical signals with broad ranges of central wavelength and bandwidth. PMID:27457024

Subwavelength grating enabled on-chip ultra-compact optical true time delay line.

PubMed

Wang, Junjia; Ashrafi, Reza; Adams, Rhys; Glesk, Ivan; Gasulla, Ivana; Capmany, José; Chen, Lawrence R

2016-07-26

An optical true time delay line (OTTDL) is a basic photonic building block that enables many microwave photonic and optical processing operations. The conventional design for an integrated OTTDL that is based on spatial diversity uses a length-variable waveguide array to create the optical time delays, which can introduce complexities in the integrated circuit design. Here we report the first ever demonstration of an integrated index-variable OTTDL that exploits spatial diversity in an equal length waveguide array. The approach uses subwavelength grating waveguides in silicon-on-insulator (SOI), which enables the realization of OTTDLs having a simple geometry and that occupy a compact chip area. Moreover, compared to conventional wavelength-variable delay lines with a few THz operation bandwidth, our index-variable OTTDL has an extremely broad operation bandwidth practically exceeding several tens of THz, which supports operation for various input optical signals with broad ranges of central wavelength and bandwidth.

Electric Motors Maintenance Planning From Its Operating Variables

NASA Astrophysics Data System (ADS)

Rodrigues, Francisco; Fonseca, Inácio; Farinha, José Torres; Ferreira, Luís; Galar, Diego

2017-09-01

The maintenance planning corresponds to an approach that seeks to maximize the availability of equipment and, consequently, increase the levels of competitiveness of companies by increasing production times. This paper presents a maintenance planning based on operating variables (number of hours worked, duty cycles, number of revolutions) to maximizing the availability of operation of electrical motors. The reading of the operating variables and its sampling is done based on predetermined sampling cycles and subsequently is made the data analysis through time series algorithms aiming to launch work orders before reaching the variables limit values. This approach is supported by tools and technologies such as logical applications that enable a graphical user interface for access to relevant information about their Physical Asset HMI (Human Machine Interface), including the control and supervision by acquisition through SCADA (Supervisory Control And data acquisition) data, also including the communication protocols among different logical applications.

Development and applications of various optimization algorithms for diesel engine combustion and emissions optimization

NASA Astrophysics Data System (ADS)

Ogren, Ryan M.

For this work, Hybrid PSO-GA and Artificial Bee Colony Optimization (ABC) algorithms are applied to the optimization of experimental diesel engine performance, to meet Environmental Protection Agency, off-road, diesel engine standards. This work is the first to apply ABC optimization to experimental engine testing. All trials were conducted at partial load on a four-cylinder, turbocharged, John Deere engine using neat-Biodiesel for PSO-GA and regular pump diesel for ABC. Key variables were altered throughout the experiments, including, fuel pressure, intake gas temperature, exhaust gas recirculation flow, fuel injection quantity for two injections, pilot injection timing and main injection timing. Both forms of optimization proved effective for optimizing engine operation. The PSO-GA hybrid was able to find a superior solution to that of ABC within fewer engine runs. Both solutions call for high exhaust gas recirculation to reduce oxide of nitrogen (NOx) emissions while also moving pilot and main fuel injections to near top dead center for improved tradeoffs between NOx and particulate matter.

Evaluation of a staged fuel combustor for turboprop engines

NASA Technical Reports Server (NTRS)

Verdouw, A. J.

1976-01-01

Proposed EPA emission regulations require emission reduction by 1979 for various gas turbine engine classes. Extensive combustion technology advancements are required to meet the proposed regulations. The T56 turboprop engine requires CO, UHC, and smoke reduction. A staged fuel combustor design was tested on a combustion rig to evaluate emission reduction potential in turboprop engines from fuel zoning. The can-type combustor has separately fueled-pilot and main combustion zones in series. The main zone fueling system was arranged for potential incorporation into the T56 with minor or no modifications to the basic engine. Three combustor variable geometry systems were incorporated to evaluate various airflow distributions. Emission results with fixed geometry operation met all proposed EPA regulations over the EPA LTO cycle. CO reduction was 82 percent, UHC reduction was 96 percent, and smoke reduction was 84 percent. NOx increased 14 percent over the LTO cycle. At high power, NOx reduction was 40 to 55 percent. This NOx reduction has potential application to stationary gas turbine powerplants which have different EPA regulations.

Comparison between direct and indirect methods to diagnose malnutrition and cardiometabolic risk in haemodialisys patients.

PubMed

Balbino, K P; Epifânio, A P S; Ribeiro, S M R; da Silva, L D M; Gouvea, M G; Hermsdorff, H H M

2017-10-01

The present study aimed to evaluate the nutritional status of patients undergoing haemodialysis (HD) by comparing nutritional risk scores with biochemical, anthropometric and body composition variables. Eighty-five individuals [65.9% male, mean (SD) age 62 (14) years] participated in a cross-sectional study. Global Objective Assessment (GOA) and Modified Global Subjective Assessment (mGSA) scores, as well as biochemical, anthropometric and body composition data, were collected using standardised procedures. The prevalence of malnutrition ranged from 20.0% (% body fat by electrical bioimpedance) to 95.3% (by GOA), depending on the indicator or score used. According to the waist circumference, 61.2% of the individuals presented abdominal obesity and visceral adipose tissue was excessive in 20% of them. Malnutrition diagnosis by GOA showed the relationship between the anthropometric and body composition indicators, as assessed by the extent that the ratings of risk nutritional/mild malnutrition and mainly moderate malnutrition were accompanied by a significant decrease in nutritional status and body composition variables. However, with respect to categories of mGSA, no statistically significant differences were observed for nutritional status and body composition variables. In the receiver operator characteristic curve analyses, mGSA and GOA were good indicators for diagnosing malnutrition because both achieved an AUC > 0.5. mGSA and GOA were more sensitive with respect to identifying individuals at nutritional risk compared to the isolated anthropometric indicators, thus indicating their utility in diagnostic malnutrition. However, individuals at high nutritional risk also presented cardiometabolic risk, as diagnosed mainly by central fat indicators, suggesting the application of both malnutrition and cardiometabolic risk markers in HD patients. © 2017 The British Dietetic Association Ltd.

O3 variability/trends in the troposphere from IASI observations in 2008-2017

NASA Astrophysics Data System (ADS)

Wespes, C.; Hurtmans, D.; Clerbaux, C.; Pierre-Francois, C.

2017-12-01

In this study, we describe the recent changes in the tropospheric ozone (O3) columns (TOCs) measured by the Infrared Atmospheric Sounding Interferometer (IASI) onboard the Metop satellites during the first ten years of the IASI operation (2008-2017). The instrument provides a unique dataset of vertically-resolved O3 profiles with a twice daily global coverage and a fairly good vertical resolution allowing us to monitor the year-to-year variability in the troposphere. The retrievals are performed using the FORLI software, a fast radiative transfer model based on the optimal estimation method, set up for near real time and large scale processing of IASI data. We differentiate trend characteristics from the seasonal and non-seasonal O3 variations captured by IASI in the troposphere by applying appropriate annual and seasonal multivariate regression models, which include important geophysical drivers of O3 variation (e.g. quasi biennial oscillations - QBO, El Niño/Southern Oscillation - ENSO, North Atlantic Oscillation-NAO) and a linear trend term, on time series of spatially gridded averaged O3. The performances of the regression models (annual vs seasonal) are first investigated. Given the large contribution of the interannual variability, we will then describe the effects of the main contributing O3 proxies (e.g. positive - or negatives - ENSO indexes measured during moderate to intense El Niño - or La Niña - episodes in the tropics) in addition to the adjusted O3 trend patterns. A special focus will be given over the Northern Hemisphere which is characterized by decreasing O3 precursor emissions (mainly over Europe and the US). FORLI O3-CO correlations patterns will also be discussed to evaluate the continental influence on the tropospheric O3 trends.

Profiles in fibromyalgia: algometry, auditory evoked potentials and clinical characterization of different subtypes.

PubMed

Triñanes, Yolanda; González-Villar, Alberto; Gómez-Perretta, Claudio; Carrillo-de-la-Peña, María T

2014-11-01

The heterogeneity found in fibromyalgia (FM) patients has led to the investigation of disease subgroups, mainly based on clinical features. The aim of this study was to test the hypothesis that clinical FM subgroups are associated with different underlying pathophysiological mechanisms. Sixty-three FM patients were classified in type I or type II, according to the Fibromyalgia Impact Questionnaire (FIQ), and in mild/moderate versus severe FM, according to the severity of three cardinal symptoms considered in the American College of Rheumatology (ACR) 2010 criteria (unrefreshed sleep, cognitive problems and fatigue). To validate the subgroups obtained by these two classifications, we calculated the area under the receiver operating characteristic curves for various clinical variables and for two potential biomarkers of FM: Response to experimental pressure pain (algometry) and the amplitude/intensity slopes of the auditory evoked potentials (AEPs) obtained to stimuli of increasing intensity. The variables that best discriminated type I versus type II were those related to depression, while the indices of clinical or experimental pain (threshold or tolerance) did not significantly differ between them. The variables that best discriminated the mild/moderate versus severe subgroups were those related to the algometry. The AEPs did not allow discrimination among the generated subsets. The FIQ-based classification allows the identification of subgroups that differ in psychological distress, while the index based on the ACR 2010 criteria seems to be useful to characterize the severity of FM mainly based on hyperalgesia. The incorporation of potential biomarkers to generate or validate classification criteria is crucial to advance in the knowledge of FM and in the understanding of pathophysiological pathways.

Near Stall Flow Analysis in the Transonic Fan of the RTA Propulsion System

NASA Technical Reports Server (NTRS)

Hah, Chunill

2010-01-01

Turbine-based propulsion systems for access to space have been investigated at NASA Glenn Research center. A ground demonstrator engine for validation testing has been developed as a part of the program. The demonstrator, the Revolutionary Turbine Accelerator (RTA-1), is a variable cycle turbofan ramjet designed to transition from an augmented turbofan to a ramjet that produces the thrust required to accelerate the vehicle to Mach 4. The RTA-1 is designed to accommodate a large variation in bypass ratio from sea level static to Mach 4 flight condition. A key component of this engine is a new fan stage that accommodates these large variations in bypass ratio and flow ranges. In the present study, unsteady flow behavior in the fan of the RTA-1 is studied in detail with large eddy simulation (LES) and the numerical results are compared with measured data. During the experimental study of the fan stage, humming sound was detected at 100 % speed near stall operation. The main purpose of the study is to investigate details of the unsteady flow behavior at near stall operation and to identify a possible cause of the hum. The large eddy simulation of the current flow field reproduces main features of the measured flow very well. The LES simulation indicates that non-synchronous flow instability develops as the fan operates toward the stall limit. The FFT analysis of the calculated wall pressure shows that the rotating flow instability has the characteristic frequency that is about 50% of the blade passing frequency.

High/variable mixture ratio O2/H2 engine

NASA Technical Reports Server (NTRS)

Adams, A.; Parsley, R. C.

1988-01-01

Vehicle/engine analysis studies have identified the High/Dual Mixture Ratio O2/H2 Engine cycle as a leading candidate for an advanced Single Stage to Orbit (SSTO) propulsion system. This cycle is designed to allow operation at a higher than normal O/F ratio of 12 during liftoff and then transition to a more optimum O/F ratio of 6 at altitude. While operation at high mixture ratios lowers specific impulse, the resultant high propellant bulk density and high power density combine to minimize the influence of atmospheric drag and low altitude gravitational forces. Transition to a lower mixture ratio at altitude then provides improved specific impulse relative to a single mixture ratio engine that must select a mixture ratio that is balanced for both low and high altitude operation. This combination of increased altitude specific impulse and high propellant bulk density more than offsets the compromised low altitude performance and results in an overall mission benefit. Two areas of technical concern relative to the execution of this dual mixture ratio cycle concept are addressed. First, actions required to transition from high to low mixture ratio are examined, including an assessment of the main chamber environment as the main chamber mixture ratio passes through stoichiometric. Secondly, two approaches to meet a requirement for high turbine power at high mixture ratio condition are examined. One approach uses high turbine temperature to produce the power and requires cooled turbines. The other approach incorporates an oxidizer-rich preburner to increase turbine work capability via increased turbine mass flow.

Enhanced Biennial Variability in the Pacific due to Atlantic Capacitor Effect after the Early 1990s

NASA Astrophysics Data System (ADS)

WANG, L.; Yu, J. Y.; Paek, H.

2016-12-01

The El Niño-Southern Oscillation (ENSO) and Pacific subtropical highs (PSHs) have major impacts on social and ecological systems through their influences on severe natural hazards including tropical storms, coastal erosions, droughts and floods. The ability to forecast ENSO and PSHs requires an understanding of the underlying physical mechanisms that drive their variability. Here we present an Atlantic capacitor effect mechanism to suggest the Atlantic as a key pacemaker of the biennial variability in the Pacific including ENSO and PSHs in recent decades, while the pacemaker was previously considered to be mainly lied within the Pacific or Indian Oceans. The "charging" (i.e., ENSO imprinting the North Tropical Atlantic (NTA) sea surface temperature (SST) via an atmospheric bridge mechanism) and "discharging" (i.e., the NTA SST triggering the following ENSO via a subtropical teleconnection mechanism) process works alternately, generating the biennial rhythmic changes in the Pacific. After the early-1990s, the positive phase of the Atlantic Multidecadal Oscillation and global warming provides more favorable background states over the NTA that enable the Atlantic capacitor effect to operate more efficiently, giving rise to enhanced biennial variability in the Pacific which may increase the occurrence frequency of severe natural hazard events. The results highlight the increasing important role of the Atlantic-Pacific coupling as an important pacemaker of the ENSO cycle in recent decades.

ACCURATE SOLUTION AND GRADIENT COMPUTATION FOR ELLIPTIC INTERFACE PROBLEMS WITH VARIABLE COEFFICIENTS

PubMed Central

LI, ZHILIN; JI, HAIFENG; CHEN, XIAOHONG

2016-01-01

A new augmented method is proposed for elliptic interface problems with a piecewise variable coefficient that has a finite jump across a smooth interface. The main motivation is not only to get a second order accurate solution but also a second order accurate gradient from each side of the interface. The key of the new method is to introduce the jump in the normal derivative of the solution as an augmented variable and re-write the interface problem as a new PDE that consists of a leading Laplacian operator plus lower order derivative terms near the interface. In this way, the leading second order derivatives jump relations are independent of the jump in the coefficient that appears only in the lower order terms after the scaling. An upwind type discretization is used for the finite difference discretization at the irregular grid points near or on the interface so that the resulting coefficient matrix is an M-matrix. A multi-grid solver is used to solve the linear system of equations and the GMRES iterative method is used to solve the augmented variable. Second order convergence for the solution and the gradient from each side of the interface has also been proved in this paper. Numerical examples for general elliptic interface problems have confirmed the theoretical analysis and efficiency of the new method. PMID:28983130

Does cost-benefit analysis or self-control predict involvement in two forms of aggression?

PubMed

Archer, John; Fernández-Fuertes, Andrés A; Thanzami, Van Lal

2010-01-01

The main aim of this research was to assess the relative association between physical aggression and (1) self-control and (2) cost-benefit assessment, these variables representing the operation of impulsive and reflective processes. Study 1 involved direct and indirect aggression among young Indian men, and Study 2 physical aggression to dating partners among Spanish adolescents. In Study 1, perceived benefits and costs but not self-control were associated with direct aggression at other men, and the association remained when their close association with indirect aggression was controlled. In Study 2, benefits and self-control showed significant and independent associations (positive for benefits, negative for self-control) with physical aggression at other-sex partners. Although being victimized was also correlated in the same direction with self-control and benefits, perpetration and being victimized were highly correlated, and there was no association between being victimized and these variables when perpetration was controlled. These results support the theory that reflective (cost-benefit analyses) processes and impulsive (self-control) processes operate in parallel in affecting aggression. The finding that male adolescents perceived more costs and fewer benefits from physical aggression to a partner than female adolescents did is consistent with findings indicating greater social disapproval of men hitting women than vice versa, rather than with the view that male violence to women is facilitated by internalized patriarchal values. (c) 2010 Wiley-Liss, Inc.

Repeatability of diagnostic ultrasonography in the assessment of the equine superficial digital flexor tendon.

PubMed

Pickersgill, C H; Marr, C M; Reid, S W

2001-01-01

A quantitative investigation of the variation that can occur during the course of ultrasonography of the equine superficial digital flexor tendons (SDFT) was undertaken. The aim of this investigation was to use an objective measure, namely the measurement of CSA, to quantify the variability occurring during the course of the ultrasonographic assessment of the equine SDFT. The effects of 3 variables on the CSA measurements were determined. 1) Image acquisition operator (IAc): two different operators undertaking the ultrasonographic examination; 2) image analysis operator (IAn): two different operators undertaking the calculation of CSA values from previously stored images; and 3) analytical equipment (used during CSA measurement) (IEq): the use of 2 different sets of equipment during calculation of CSA values. Tendon cross-sectional area (CSA) measurements were used as the comparative variable of 3 potential sources: interoperator, during image acquisition; interoperator, during CSA measurement; and intraoperator, when using different analytical equipment. Two operators obtained transverse ultrasonographic images from the forelimb SDFTs of 16 National Hunt (NH) Thoroughbred (TB) racehorses, each undertaking analysis of their own and the other operator's images. One operator undertook analysis of their images using 2 sets of equipment. There was no statistically significant difference in the results obtained when different operators undertook image acquisition (P>0.05). At all but the most distal level, there was no significant difference when different equipment was used during analysis (P>0.05). A significant difference (P<0.01) was reported when different operators undertook image analysis, one operator consistently returning larger measurements. Different operators undertaking different stages of an examination can result in significant variability. To reduce confounding during ultrasonographic investigations involving multiple persons, one operator should undertake image analysis, although different operators may undertake image acquisition.

Risk assessment of maintenance operations: the analysis of performing task and accident mechanism.

PubMed

Carrillo-Castrillo, Jesús A; Rubio-Romero, Juan Carlos; Guadix, Jose; Onieva, Luis

2015-01-01

Maintenance operations cover a great number of occupations. Most small and medium-sized enterprises lack the appropriate information to conduct risk assessments of maintenance operations. The objective of this research is to provide a method based on the concepts of task and accident mechanisms for an initial risk assessment by taking into consideration the prevalence and severity of the maintenance accidents reported. Data were gathered from 11,190 reported accidents in maintenance operations in the manufacturing sector of Andalusia from 2003 to 2012. By using a semi-quantitative methodology, likelihood and severity were evaluated based on the actual distribution of accident mechanisms in each of the tasks. Accident mechanisms and tasks were identified by using those variables included in the European Statistics of Accidents at Work methodology. As main results, the estimated risk of the most frequent accident mechanisms identified for each of the analysed tasks is low and the only accident mechanisms with medium risk are accidents when lifting or pushing with physical stress on the musculoskeletal system in tasks involving carrying, and impacts against objects after slipping or stumbling for tasks involving movements. The prioritisation of public preventive actions for the accident mechanisms with a higher estimated risk is highly recommended.

EMD-Based Methodology for the Identification of a High-Speed Train Running in a Gear Operating State.

PubMed

Bustos, Alejandro; Rubio, Higinio; Castejón, Cristina; García-Prada, Juan Carlos

2018-03-06

An efficient maintenance is a key consideration in systems of railway transport, especially in high-speed trains, in order to avoid accidents with catastrophic consequences. In this sense, having a method that allows for the early detection of defects in critical elements, such as the bogie mechanical components, is a crucial for increasing the availability of rolling stock and reducing maintenance costs. The main contribution of this work is the proposal of a methodology that, based on classical signal processing techniques, provides a set of parameters for the fast identification of the operating state of a critical mechanical system. With this methodology, the vibratory behaviour of a very complex mechanical system is characterised, through variable inputs, which will allow for the detection of possible changes in the mechanical elements. This methodology is applied to a real high-speed train in commercial service, with the aim of studying the vibratory behaviour of the train (specifically, the bogie) before and after a maintenance operation. The results obtained with this methodology demonstrated the usefulness of the new procedure and allowed for the disclosure of reductions between 15% and 45% in the spectral power of selected Intrinsic Mode Functions (IMFs) after the maintenance operation.

EMD-Based Methodology for the Identification of a High-Speed Train Running in a Gear Operating State

PubMed Central

García-Prada, Juan Carlos

2018-01-01

An efficient maintenance is a key consideration in systems of railway transport, especially in high-speed trains, in order to avoid accidents with catastrophic consequences. In this sense, having a method that allows for the early detection of defects in critical elements, such as the bogie mechanical components, is a crucial for increasing the availability of rolling stock and reducing maintenance costs. The main contribution of this work is the proposal of a methodology that, based on classical signal processing techniques, provides a set of parameters for the fast identification of the operating state of a critical mechanical system. With this methodology, the vibratory behaviour of a very complex mechanical system is characterised, through variable inputs, which will allow for the detection of possible changes in the mechanical elements. This methodology is applied to a real high-speed train in commercial service, with the aim of studying the vibratory behaviour of the train (specifically, the bogie) before and after a maintenance operation. The results obtained with this methodology demonstrated the usefulness of the new procedure and allowed for the disclosure of reductions between 15% and 45% in the spectral power of selected Intrinsic Mode Functions (IMFs) after the maintenance operation. PMID:29509690

Variable-Period Undulators For Synchrotron Radiation

DOEpatents

Shenoy, Gopal; Lewellen, John; Shu, Deming; Vinokurov, Nikolai

2005-02-22

A new and improved undulator design is provided that enables a variable period length for the production of synchrotron radiation from both medium-energy and high-energy storage rings. The variable period length is achieved using a staggered array of pole pieces made up of high permeability material, permanent magnet material, or an electromagnetic structure. The pole pieces are separated by a variable width space. The sum of the variable width space and the pole width would therefore define the period of the undulator. Features and advantages of the invention include broad photon energy tunability, constant power operation and constant brilliance operation.

Search for Variables in the Kepler Field on DASCH Plates

NASA Astrophysics Data System (ADS)

Tang, Sumin; Grindlay, J.; Los, E.; Servillat, M.

2011-01-01

The Digital Access to a Sky Century @ Harvard (DASCH) is a project to digitize the half a million glass photographic plates over the period 1880s-1980s. This 100 year coverage is a unique resource for studying temporal variations in the universe. Here we present our variable search algorithms and variable catalog in the Kepler fields based on 3000 scanned plates. We use the KIC spectral classifications to search for long-term variability of any main sequence stars, particularly M dwarfs. We apply a variability search technique developed for DASCH and set limits on the fraction of main sequence stars, by spectral type, which show detectable (>0.2mag) variability on timescales 10-100y. Such limits are of particular interest for M dwarfs given the recent discoveries of their planet systems.

Applications of variable speed control for contending with recurrent highway congestion.

DOT National Transportation Integrated Search

2014-07-01

This research project developed vital operational guidelines for design of a variable speed limit (VSL) system and its integrated operations with ramp metering control in contending with recurrent highway congestion. The developed guidelines can serv...

Variable speed generator technology options for wind turbine generators

NASA Technical Reports Server (NTRS)

Lipo, T. A.

1995-01-01

The electrical system options for variable speed operation of a wind turbine generator are treated in this paper. The key operating characteristics of each system are discussed and the major advantages and disadvantages of each are identified

Analysis of operating reserve demand curves in power system operations in the presence of variable generation

DOE PAGES

Krad, Ibrahim; Gao, David Wenzhong; Ela, Erik; ...

2017-06-07

The electric power industry landscape is continually evolving. As emerging technologies such as wind and solar generating systems become more cost effective, traditional power system operating strategies will need to be re-evaluated. The presence of wind and solar generation (commonly referred to as variable generation or VG) can increase variability and uncertainty in the net-load profile. One mechanism to mitigate this issue is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increased variability and uncertainty occurring at finer temporal resolutions. A newmore » operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this study, and its implications on power system operations are analyzed. Results show that flexibility reserve products can improve economic metrics, particularly in significantly reducing the number of scarcity pricing events, with minimal impacts on reliability metrics and production costs. Furthermore, the production costs increased due to increased VG curtailment - i.e. including the flexible ramping product in the commitment of excess thermal capacity that needed to remain online at the expense of VG output.« less

Analysis of operating reserve demand curves in power system operations in the presence of variable generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Gao, David Wenzhong; Ela, Erik

The electric power industry landscape is continually evolving. As emerging technologies such as wind and solar generating systems become more cost effective, traditional power system operating strategies will need to be re-evaluated. The presence of wind and solar generation (commonly referred to as variable generation or VG) can increase variability and uncertainty in the net-load profile. One mechanism to mitigate this issue is to schedule and dispatch additional operating reserves. These operating reserves aim to ensure that there is enough capacity online in the system to account for the increased variability and uncertainty occurring at finer temporal resolutions. A newmore » operating reserve strategy, referred to as flexibility reserve, has been introduced in some regions. A similar implementation is explored in this study, and its implications on power system operations are analyzed. Results show that flexibility reserve products can improve economic metrics, particularly in significantly reducing the number of scarcity pricing events, with minimal impacts on reliability metrics and production costs. Furthermore, the production costs increased due to increased VG curtailment - i.e. including the flexible ramping product in the commitment of excess thermal capacity that needed to remain online at the expense of VG output.« less

Power Supply for Variable Frequency Induction Heating Using MERS Soft-Switching High Frequency Inverter

NASA Astrophysics Data System (ADS)

Isobe, Takanori; Kitahara, Tadayuki; Fukutani, Kazuhiko; Shimada, Ryuichi

Variable frequency induction heating has great potential for industrial heating applications due to the possibility of achieving heating distribution control; however, large-scale induction heating with variable frequency has not yet been introduced for practical use. This paper proposes a high frequency soft-switching inverter for induction heating that can achieve variable frequency operation. One challenge of variable frequency induction heating is increasing power electronics ratings. This paper indicates that its current source type dc-link configuration and soft-switching characteristics can make it possible to build a large-scale system with variable frequency capability. A 90-kVA 150-1000Hz variable frequency experimental power supply for steel strip induction heating was developed. Experiments confirmed the feasibility of variable frequency induction heating with proposed converter and the advantages of variable frequency operation.

Precision Viticulture : is it relevant to manage the vineyard according to the within field spatial variability of the environment ?

NASA Astrophysics Data System (ADS)

Tisseyre, Bruno

2015-04-01

For more than 15 years, research projects are conducted in the precision viticulture (PV) area around the world. These research projects have provided new insights into the within-field variability in viticulture. Indeed, access to high spatial resolution data (remote sensing, embedded sensors, etc.) changes the knowledge we have of the fields in viticulture. In particular, the field which was until now considered as a homogeneous management unit, presents actually a high spatial variability in terms of yield, vigour an quality. This knowledge will lead (and is already causing) changes on how to manage the vineyard and the quality of the harvest at the within field scale. From the experimental results obtained in various countries of the world, the goal of the presentation is to provide figures on: - the spatial variability of the main parameters (yield, vigor, quality), and how this variability is organized spatially, - the temporal stability of the observed spatial variability and the potential link with environmental parameters like soil, topography, soil water availability, etc. - information sources available at a high spatial resolution conventionally used in precision agriculture likely to highlight this spatial variability (multi-spectral images, soil electrical conductivity, etc.) and the limitations that these information sources are likely to present in viticulture. Several strategies are currently being developed to take into account the within field variability in viticulture. They are based on the development of specific equipments, sensors, actuators and site specific strategies with the aim of adapting the vineyard operations at the within-field level. These strategies will be presented briefly in two ways : - Site specific operations (fertilization, pruning, thinning, irrigation, etc.) in order to counteract the effects of the environment and to obtain a final product with a controlled and consistent wine quality, - Differential harvesting with the objective to take advantage of the observed spatial variability to produce different quality of wines. These later approach tends to produce very different quality wines which will be blended to control the final quality and/or marketed differently. These applications show that the environment and its spatial variability can be valued with the goal of controlling the final quality of the wine produced. Technologies to characterize the spatial variability of vine fields are currently in rapid evolution. They will significantly impact production methods and management strategies of the vineyard. In its last part, the presentation will summarize the technologies likely to impact the knowledge and the vineyard management either at the field level, at the vineyard level or at the regional level. A brief overview of the needs in terms of information processing will be also performed. A reflection on the difficulties that might limit the adoption of precision viticulture technologies (PV) will be done. Indeed, although very informative, PV entails high costs of information acquisition and data processing. Cost is one of the major obstacles to the dissemination of these tools and services to the majority of wine producers. In this context, the pooling of investments is a choke point to make the VP accessible to the highest number of growers. Thus, to be adopted, the VP will necessarily satisfy the operational requirements at the field level, but also throughout the whole production area (at the regional level). This working scale raises new scientific questions to be addressed.

The high opening of the right bronchial artery with a non-typical course.

PubMed

Maciejewski, R; Madej, B; Anasiewicz, A

1995-01-01

Authors describing the bronchial vessels agree to the fact that they are characterised by a great variability in regard to their number and the place where they leave aorta (1, 2, 6). The characteristic feature of the right bronchial artery is that it often forms common trunks with other vessels (mainly with the first right aortic intercostal branch or with one of the upper oesophageal arteries). It can also have a common let-out trunk with the left upper bronchial artery (4). Bearing in mind that the operations on trachea and bronchi are difficult, and that it is very important to maintain the blood supply of the walls in the operated organs we have decided to publish our observations. They refer to a case, not described before, in which the right bronchial artery left the aortic arch in a high position making the vascular supply to the front lower half of the trachea and its bifurcation. Then, it went down to the membranous part of the right bronchus.

Emergent mechanics, quantum and un-quantum

NASA Astrophysics Data System (ADS)

Ralston, John P.

2013-10-01

There is great interest in quantum mechanics as an "emergent" phenomenon. The program holds that nonobvious patterns and laws can emerge from complicated physical systems operating by more fundamental rules. We find a new approach where quantum mechanics itself should be viewed as an information management tool not derived from physics nor depending on physics. The main accomplishment of quantum-style theory comes in expanding the notion of probability. We construct a map from macroscopic information as data" to quantum probability. The map allows a hidden variable description for quantum states, and efficient use of the helpful tools of quantum mechanics in unlimited circumstances. Quantum dynamics via the time-dependent Shroedinger equation or operator methods actually represents a restricted class of classical Hamiltonian or Lagrangian dynamics, albeit with different numbers of degrees of freedom. We show that under wide circumstances such dynamics emerges from structureless dynamical systems. The uses of the quantum information management tools are illustrated by numerical experiments and practical applications

Creation of Power Reserves Under the Market Economy Conditions

NASA Astrophysics Data System (ADS)

Mahnitko, A.; Gerhards, J.; Lomane, T.; Ribakov, S.

2008-09-01

The main task of the control over an electric power system (EPS) is to ensure reliable power supply at the least cost. In this case, requirements to the electric power quality, power supply reliability and cost limitations on the energy resources must be observed. The available power reserve in an EPS is the necessary condition to keep it in operation with maintenance of normal operating variables (frequency, node voltage, power flows via the transmission lines, etc.). The authors examine possibilities to create power reserves that could be offered for sale by the electric power producer. They consider a procedure of price formation for the power reserves and propose a relevant mathematical model for a united EPS, the initial data being the fuel-cost functions for individual systems, technological limitations on the active power generation and consumers' load. As the criterion of optimization the maximum profit for the producer is taken. The model is exemplified by a concentrated EPS. The computations have been performed using the MATLAB program.

An investigation on wireless sensors for asset management and health monitoring of civil structures

NASA Astrophysics Data System (ADS)

Furkan, Mustafa; Mao, Qiang; Mazzotti, Matteo; DeVitis, John; Sumitro, S. Paul; Faridazar, Fred; Aktan, A. Emin; Moon, Franklin; Bartoli, Ivan

2016-04-01

Application of wireless sensors and sensor networks for Structural Health Monitoring has been investigated for a long time. Key limitations for practical use are energy requirements, connectivity, and integration with existing systems. Current sensors and sensor networks mainly rely on wired connectivity for communication and external power source for energy. This paper presents a suite of wireless sensors that are low-cost, maintenance free, rugged, and have long service life. The majority of the sensors considered were designed by transforming existing, proven, and robust wired sensors into wireless units. In this study, the wireless sensors were tested in laboratory conditions for calibration and evaluation along with wired sensors. The experimental results were also compared to theoretical results. The tests mostly show satisfactory performance of the wireless units. This work is part of a broader Federal Highway Administration sponsored project intended to ultimately validate a wireless sensing system on a real, operating structure to account for all the uncertainties, environmental conditions and operational variability that are encountered in the field.

Assessment of the relationship of government spending on social assistance programs with Brazilian macroeconomic variables

NASA Astrophysics Data System (ADS)

de Senna, Viviane; Souza, Adriano Mendonça

2016-11-01

Since the 1988 Federal Constitution social assistance has become a duty of the State and a right to everyone, guaranteeing the population a dignified life. To ensure these rights federal government has created programs that can supply the main needs of people in extreme poverty. Among the programs that provide social assistance to the population, the best known are the ;Bolsa Família; Program - PBF and the Continuous Cash Benefit - Continuous Cash Benefit - BPC. This research's main purpose is to analyze the relationship between the main macroeconomic variables and the Federal government spending on social welfare policy in the period from January 2004 to August 2014. The used methodologies are the Vector auto regression model - VAR and Error Correction Vector - VEC. The conclusion, was that there is a meaningful relationship between macroeconomic variables and social assistance programs. This indicates that if the government takes a more abrupt resolution in changing the existing programs it will result in fluctuations in the main macroeconomic variables interfering with the stability of Brazilian domestic economy up to twelve months.

Value of Construction Company and its Dependence on Significant Variables

NASA Astrophysics Data System (ADS)

Vítková, E.; Hromádka, V.; Ondrušková, E.

2017-10-01

The paper deals with the value of the construction company assessment respecting usable approaches and determinable variables. The reasons of the value of the construction company assessment are different, but the most important reasons are the sale or the purchase of the company, the liquidation of the company, the fusion of the company with another subject or the others. According the reason of the value assessment it is possible to determine theoretically different approaches for valuation, mainly it concerns about the yield method of valuation and the proprietary method of valuation. Both approaches are dependant of detailed input variables, which quality will influence the final assessment of the company´s value. The main objective of the paper is to suggest, according to the analysis, possible ways of input variables, mainly in the form of expected cash-flows or the profit, determination. The paper is focused mainly on methods of time series analysis, regression analysis and mathematical simulation utilization. As the output, the results of the analysis on the case study will be demonstrated.

Energy management of a university campus utilizing short-term load forecasting with an artificial neural network

NASA Astrophysics Data System (ADS)

Palchak, David

Electrical load forecasting is a tool that has been utilized by distribution designers and operators as a means for resource planning and generation dispatch. The techniques employed in these predictions are proving useful in the growing market of consumer, or end-user, participation in electrical energy consumption. These predictions are based on exogenous variables, such as weather, and time variables, such as day of week and time of day as well as prior energy consumption patterns. The participation of the end-user is a cornerstone of the Smart Grid initiative presented in the Energy Independence and Security Act of 2007, and is being made possible by the emergence of enabling technologies such as advanced metering infrastructure. The optimal application of the data provided by an advanced metering infrastructure is the primary motivation for the work done in this thesis. The methodology for using this data in an energy management scheme that utilizes a short-term load forecast is presented. The objective of this research is to quantify opportunities for a range of energy management and operation cost savings of a university campus through the use of a forecasted daily electrical load profile. The proposed algorithm for short-term load forecasting is optimized for Colorado State University's main campus, and utilizes an artificial neural network that accepts weather and time variables as inputs. The performance of the predicted daily electrical load is evaluated using a number of error measurements that seek to quantify the best application of the forecast. The energy management presented utilizes historical electrical load data from the local service provider to optimize the time of day that electrical loads are being managed. Finally, the utilization of forecasts in the presented energy management scenario is evaluated based on cost and energy savings.

Decreased Radiation Exposure and Increased Efficacy in Extracorporeal Lithotripsy Using a New Ultrasound Stone Locking System.

PubMed

Abid, Nadia; Ravier, Emmanuel; Promeyrat, Xavier; Codas, Ricardo; Fehri, Hakim Fassi; Crouzet, Sebastien; Martin, Xavier

2015-11-01

To compare fluoroscopy duration, radiation dose, and efficacy of two ultrasound stone localization systems during extracorporeal shockwave lithotripsy (SWL) treatment. Monocentric prospective data were obtained from patients consecutively treated for renal stones using the Sonolith(®) i-sys (EDAP TMS) lithotripter, with fluoroscopy combined with ultrasound localization using an "outline" Automatic Ultrasound Positioning Support (AUPS) (group A), or the "free-line" Visio-Track (VT) (EDAP-TMS) hand-held three-dimensional ultrasound stone locking system (group B). Efficacy rate was defined as the within-groups proportion stone free or with partial stone fragmentation not needing additional procedures. Statistical analysis used Pearson chi-square tests for categoric variables, nonparametric Mann-Whitney tests for continuous variables, and linear regression for operator learning curve with VT. Continuous variables were reported as median (range) values. Patients in group A (n=73) and group B (n=81) were comparable in baseline characteristics (age, kidney stone size, others) and in SWL application (duration, number of shocks, energy [Joules]). During SWL, the median (range) duration (seconds) of radiation exposure was 159.5 (0-690) in group A and 3.5 (0-478) in group B (P<0.001) and irradiation dose (mGy.cm(2)), 10598 (0-54843) in group A and 163 (0-13926) in group B (P<0.001). Fluoroscopy time significantly decreased with operator experience using VT. The efficacy rate was 54.5% in group A and 79.5% in group B (P=0.001). VT significantly reduced fluoroscopy use during SWL and the duration and dose of patient exposure to ionizing radiation. Stone treatment efficacy was significantly greater with VT mainly because of a better real-time monitoring of the stone.

Factors predictive of obstructive sleep apnea in patients undergoing pre-operative evaluation for bariatric surgery and referred to a sleep laboratory for polysomnography

PubMed Central

Duarte, Ricardo Luiz de Menezes; Magalhães-da-Silveira, Flavio José

2015-01-01

Objective: To identify the main predictive factors for obtaining a diagnosis of obstructive sleep apnea (OSA) in patients awaiting bariatric surgery. Methods: Retrospective study of consecutive patients undergoing pre-operative evaluation for bariatric surgery and referred for in-laboratory polysomnography. Eight variables were evaluated: sex, age, neck circumference (NC), BMI, Epworth Sleepiness Scale (ESS) score, snoring, observed apnea, and hypertension. We employed ROC curve analysis to determine the best cut-off value for each variable and multiple linear regression to identify independent predictors of OSA severity. Results: We evaluated 1,089 patients, of whom 781 (71.7%) were female. The overall prevalence of OSA-defined as an apnea/hypopnea index (AHI) ≥ 5.0 events/h-was 74.8%. The best cut-off values for NC, BMI, age, and ESS score were 42 cm, 42 kg/m2, 37 years, and 10 points, respectively. All eight variables were found to be independent predictors of a diagnosis of OSA in general, and all but one were found to be independent predictors of a diagnosis of moderate/severe OSA (AHI ≥ 15.0 events/h), the exception being hypertension. We devised a 6-item model, designated the NO-OSAS model (NC, Obesity, Observed apnea, Snoring, Age, and Sex), with a cut-off value of ≥ 3 for identifying high-risk patients. For a diagnosis of moderate/severe OSA, the model showed 70.8% accuracy, 82.8% sensitivity, and 57.9% specificity. Conclusions: In our sample of patients awaiting bariatric surgery, there was a high prevalence of OSA. At a cut-off value of ≥ 3, the proposed 6-item model showed good accuracy for a diagnosis of moderate/severe OSA. PMID:26578136

Temporal variability of the bioaerosol background at a subway station: concentration level, size distribution, and diversity of airborne bacteria.

PubMed

Dybwad, Marius; Skogan, Gunnar; Blatny, Janet Martha

2014-01-01

Naturally occurring bioaerosol environments may present a challenge to biological detection-identification-monitoring (BIODIM) systems aiming at rapid and reliable warning of bioterrorism incidents. One way to improve the operational performance of BIODIM systems is to increase our understanding of relevant bioaerosol backgrounds. Subway stations are enclosed public environments which may be regarded as potential bioterrorism targets. This study provides novel information concerning the temporal variability of the concentration level, size distribution, and diversity of airborne bacteria in a Norwegian subway station. Three different air samplers were used during a 72-h sampling campaign in February 2011. The results suggested that the airborne bacterial environment was stable between days and seasons, while the intraday variability was found to be substantial, although often following a consistent diurnal pattern. The bacterial levels ranged from not detected to 10(3) CFU m(-3) and generally showed increased levels during the daytime compared to the nighttime levels, as well as during rush hours compared to non-rush hours. The airborne bacterial levels showed rapid temporal variation (up to 270-fold) on some occasions, both consistent and inconsistent with the diurnal profile. Airborne bacterium-containing particles were distributed between different sizes for particles of >1.1 μm, although ∼50% were between 1.1 and 3.3 μm. Anthropogenic activities (mainly passengers) were demonstrated as major sources of airborne bacteria and predominantly contributed 1.1- to 3.3-μm bacterium-containing particles. Our findings contribute to the development of realistic testing and evaluation schemes for BIODIM equipment by providing information that may be used to simulate operational bioaerosol backgrounds during controlled aerosol chamber-based challenge tests with biological threat agents.

Temporal Variability of the Bioaerosol Background at a Subway Station: Concentration Level, Size Distribution, and Diversity of Airborne Bacteria

PubMed Central

Dybwad, Marius; Skogan, Gunnar

2014-01-01

Naturally occurring bioaerosol environments may present a challenge to biological detection-identification-monitoring (BIODIM) systems aiming at rapid and reliable warning of bioterrorism incidents. One way to improve the operational performance of BIODIM systems is to increase our understanding of relevant bioaerosol backgrounds. Subway stations are enclosed public environments which may be regarded as potential bioterrorism targets. This study provides novel information concerning the temporal variability of the concentration level, size distribution, and diversity of airborne bacteria in a Norwegian subway station. Three different air samplers were used during a 72-h sampling campaign in February 2011. The results suggested that the airborne bacterial environment was stable between days and seasons, while the intraday variability was found to be substantial, although often following a consistent diurnal pattern. The bacterial levels ranged from not detected to 103 CFU m−3 and generally showed increased levels during the daytime compared to the nighttime levels, as well as during rush hours compared to non-rush hours. The airborne bacterial levels showed rapid temporal variation (up to 270-fold) on some occasions, both consistent and inconsistent with the diurnal profile. Airborne bacterium-containing particles were distributed between different sizes for particles of >1.1 μm, although ∼50% were between 1.1 and 3.3 μm. Anthropogenic activities (mainly passengers) were demonstrated as major sources of airborne bacteria and predominantly contributed 1.1- to 3.3-μm bacterium-containing particles. Our findings contribute to the development of realistic testing and evaluation schemes for BIODIM equipment by providing information that may be used to simulate operational bioaerosol backgrounds during controlled aerosol chamber-based challenge tests with biological threat agents. PMID:24162566

Variational Koopman models: Slow collective variables and molecular kinetics from short off-equilibrium simulations

NASA Astrophysics Data System (ADS)

Wu, Hao; Nüske, Feliks; Paul, Fabian; Klus, Stefan; Koltai, Péter; Noé, Frank

2017-04-01

Markov state models (MSMs) and master equation models are popular approaches to approximate molecular kinetics, equilibria, metastable states, and reaction coordinates in terms of a state space discretization usually obtained by clustering. Recently, a powerful generalization of MSMs has been introduced, the variational approach conformation dynamics/molecular kinetics (VAC) and its special case the time-lagged independent component analysis (TICA), which allow us to approximate slow collective variables and molecular kinetics by linear combinations of smooth basis functions or order parameters. While it is known how to estimate MSMs from trajectories whose starting points are not sampled from an equilibrium ensemble, this has not yet been the case for TICA and the VAC. Previous estimates from short trajectories have been strongly biased and thus not variationally optimal. Here, we employ the Koopman operator theory and the ideas from dynamic mode decomposition to extend the VAC and TICA to non-equilibrium data. The main insight is that the VAC and TICA provide a coefficient matrix that we call Koopman model, as it approximates the underlying dynamical (Koopman) operator in conjunction with the basis set used. This Koopman model can be used to compute a stationary vector to reweight the data to equilibrium. From such a Koopman-reweighted sample, equilibrium expectation values and variationally optimal reversible Koopman models can be constructed even with short simulations. The Koopman model can be used to propagate densities, and its eigenvalue decomposition provides estimates of relaxation time scales and slow collective variables for dimension reduction. Koopman models are generalizations of Markov state models, TICA, and the linear VAC and allow molecular kinetics to be described without a cluster discretization.

A Comprehensive Comparison of Current Operating Reserve Methodologies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Ibanez, Eduardo; Gao, Wenzhong

Electric power systems are currently experiencing a paradigm shift from a traditionally static system to a system that is becoming increasingly more dynamic and variable. Emerging technologies are forcing power system operators to adapt to their performance characteristics. These technologies, such as distributed generation and energy storage systems, have changed the traditional idea of a distribution system with power flowing in one direction into a distribution system with bidirectional flows. Variable generation, in the form of wind and solar generation, also increases the variability and uncertainty in the system. As such, power system operators are revisiting the ways in whichmore » they treat this evolving power system, namely by modifying their operating reserve methodologies. This paper intends to show an in-depth analysis on different operating reserve methodologies and investigate their impacts on power system reliability and economic efficiency.« less

Time-resolved photometry of the nova remnants DM Gem, CP Lac, GI Mon, V400 Per, CT Ser and XX Tau

NASA Astrophysics Data System (ADS)

Rodríguez-Gil, P.; Torres, M. A. P.

2005-02-01

We present the first results of a photometric survey of poorly studied nova remnants in the Northern Hemisphere. The main results are as follows: DM Gem shows a modulation at 0.123 d (probably linked to the orbit) and rapid variations at ˜ 22 min. A moderate resolution spectrum taken at the time of the photometric observations shows intense He II 4686 and Bowen emission, characteristic of an intermediate polar or a SW Sex star. Variability at 0.127 d and intense flickering (or quasi-periodic oscillations) are the main features of the light curve of CP Lac. A 0.1-mag dip lasting for ˜ 45 min is observed in GI Mon, which could be an eclipse. A clear modulation (probably related to the orbital motion) either at 0.179 d or 0.152 d is observed in the B-band light curve of V400 Per. The results for CT Ser point to an orbital period close to 0.16 d. Intense flickering is also characteristic of this old nova. Finally, XX Tau shows a possible periodic signal near 0.14 d and displays fast variability at ˜ 24 min. Its brightness seems to be modulated at ˜ 5 d. We relate this long periodicity to the motion of an eccentric/tilted accretion disc in the binary. Based in part on observations made with the Jacobus Kapteyn Telescope, which was operated on the island of La Palma by the Isaac Newton Group in the Spanish Observatorio del Roque de los Muchachos of the Instituto de Astrofísica de Canarias (IAC), and on observations made with the IAC80 telescope, operated on the island of Tenerife by the IAC in the Spanish Observatorio del Teide of the IAC. Observations were also obtained at the FLWO Observatory, a facility of the Smithsonian Institution.

Development of manuals for the effective use of variable message signs.

DOT National Transportation Integrated Search

1995-01-01

A comprehensive research effort to develop operator's manuals for variable message signs (VMSs) was undertaken to improve the operations of both portable and permanent (fixed-site) VMSs in Virginia. This report describes the development of two manual...

Fixed-speed and Variable-speed Pumped Storage Dispatch Model in Power Systems with High Renewable Penetration

NASA Astrophysics Data System (ADS)

Yuan, Bo; Zong, Jin; Xu, Zhicheng

2018-06-01

According to different operating characteristics of pumped storage fixed speed unit and variable speed unit, a joint dispatching model of pumped storage unit and other types of units based on mixed integer linear optimization is constructed. The model takes into account the operating conditions, reservoir capacity, cycle type and other pumped storage unit constraints, but also consider the frequent start and stop and the stability of the operation of the unit caused by the loss. Using the Cplex solver to solve the model, the empirical example of the provincial power grid shows that the model can effectively arrange the pumping storage speed and the dispatching operation of the variable speed unit under the precondition of economic life of the unit, and give full play to the function of peak shaving and accommodating new energy. Because of its more flexible regulation characteristics of power generation and pumping conditions, the variable speed unit can better improve the operating conditions of other units in the system and promote the new energy dissipation.

High Velocity Jet Noise Source Location and Reduction. Task 6. Supplement. Computer Programs: Engineering Correlation (M*S) Jet Noise Prediction Method and Unified Aeroacoustic Prediction Model (M*G*B) for Nozzles of Arbitary Shape.

DTIC Science & Technology

1979-03-01

LSPFIT 112 4.3.5 SLICE 112 4.3.6 CRD 113 4.3.7 OUTPUT 113 4.3.8 SHOCK 115 4.3.9 ATMOS 115 4.3.10 PNLC 115 4.4 Program Usage and Logic 116 4.5 Description...number MAIN, SLICE, OUTPUT F Intermediate variable LSPFIT FAC Intermediate variable PNLC FC Center frequency SLICE FIRSTU Flight velocity Ua MAIN, SLICE...Index CRD J211 Index CRD K Index, also wave number MAIN, SLICE, PNLC KN Surrounding boundary index MAIN KNCAS Case counter MAIN KNK Surrounding

Model for the techno-economic analysis of common work of wind power and CCGT power plant to offer constant level of power in the electricity market

NASA Astrophysics Data System (ADS)

Tomsic, Z.; Rajsl, I.; Filipovic, M.

2017-11-01

Wind power varies over time, mainly under the influence of meteorological fluctuations. The variations occur on all time scales. Understanding these variations and their predictability is of key importance for the integration and optimal utilization of wind in the power system. There are two major attributes of variable generation that notably impact the participation on power exchanges: Variability (the output of variable generation changes and resulting in fluctuations in the plant output on all time scales) and Uncertainty (the magnitude and timing of variable generation output is less predictable, wind power output has low levels of predictability). Because of these variability and uncertainty wind plants cannot participate to electricity market, especially to power exchanges. For this purpose, the paper presents techno-economic analysis of work of wind plants together with combined cycle gas turbine (CCGT) plant as support for offering continues power to electricity market. A model of wind farms and CCGT plant was developed in program PLEXOS based on real hourly input data and all characteristics of CCGT with especial analysis of techno-economic characteristics of different types of starts and stops of the plant. The Model analyzes the followings: costs of different start-stop characteristics (hot, warm, cold start-ups and shutdowns) and part load performance of CCGT. Besides the costs, the technical restrictions were considered such as start-up time depending on outage duration, minimum operation time, and minimum load or peaking capability. For calculation purposes, the following parameters are necessary to know in order to be able to economically evaluate changes in the start-up process: ramp up and down rate, time of start time reduction, fuel mass flow during start, electricity production during start, variable cost of start-up process, cost and charges for life time consumption for each start and start type, remuneration during start up time regarding expected or unexpected starts, the cost and revenues for balancing energy (important when participating in electricity market), and the cost or revenues for CO2-certificates. Main motivation for this analysis is to investigate possibilities to participate on power exchanges by offering continues guarantied power from wind plants by backing-up them with CCGT power plant.

Hydraulic Modeling and Evolutionary Optimization for Enhanced Real-Time Decision Support of Combined Sewer Overflows

NASA Astrophysics Data System (ADS)

Zimmer, A. L.; Minsker, B. S.; Schmidt, A. R.; Ostfeld, A.

2011-12-01

Real-time mitigation of combined sewer overflows (CSOs) requires evaluation of multiple operational strategies during rapidly changing rainfall events. Simulation models for hydraulically complex systems can effectively provide decision support for short time intervals when coupled with efficient optimization. This work seeks to reduce CSOs for a test case roughly based on the North Branch of the Chicago Tunnel and Reservoir Plan (TARP), which is operated by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC). The North Branch tunnel flows to a junction with the main TARP system. The Chicago combined sewer system alleviates potential CSOs by directing high interceptor flows through sluice gates and dropshafts to a deep tunnel. Decision variables to control CSOs consist of sluice gate positions that control water flow to the tunnel as well as a treatment plant pumping rate that lowers interceptor water levels. A physics-based numerical model is used to simulate the hydraulic effects of changes in the decision variables. The numerical model is step-wise steady and conserves water mass and momentum at each time step by iterating through a series of look-up tables. The look-up tables are constructed offline to avoid extensive real-time calculations, and describe conduit storage and water elevations as a function of flow. A genetic algorithm (GA) is used to minimize CSOs at each time interval within a moving horizon framework. Decision variables are coded at 15-minute increments and GA solutions are two hours in duration. At each 15-minute interval, the algorithm identifies a good solution for a two-hour rainfall forecast. Three GA modifications help reduce optimization time. The first adjustment reduces the search alphabet by eliminating sluice gate positions that do not influence overflow volume. The second GA retains knowledge of the best decision at the previous interval by shifting the genes in the best previous sequence to initialize search at the new interval. The third approach is a micro-GA with a small population size and high diversity. Current tunnel operations attempt to avoid dropshaft geysers by simultaneously closing all sluice gates when the downstream end of the deep tunnel pressurizes. In an effort to further reduce CSOs, this research introduces a constraint that specifies a maximum allowable tunnel flow to prevent pressurization. The downstream junction depth is bounded by two flow conditions: a low tunnel water level represents inflow from the main system only, while a higher level includes main system flow as well as all possible North Branch inflow. If the lower of the two tunnel levels is pressurized, no North Branch flow is allowed to enter the junction. If only the higher level pressurizes, a linear rating is used to restrict the total North Branch flow below the volume that pressurizes the boundary. The numerical model is successfully calibrated to EPA SWMM and efficiently portrays system hydraulics in real-time. Results on the three GA approaches as well as impacts of various policies for the downstream constraint will be presented at the conference.

Peak flow regression equations For small, ungaged streams in Maine: Comparing map-based to field-based variables

USGS Publications Warehouse

Lombard, Pamela J.; Hodgkins, Glenn A.

2015-01-01

Regression equations to estimate peak streamflows with 1- to 500-year recurrence intervals (annual exceedance probabilities from 99 to 0.2 percent, respectively) were developed for small, ungaged streams in Maine. Equations presented here are the best available equations for estimating peak flows at ungaged basins in Maine with drainage areas from 0.3 to 12 square miles (mi2). Previously developed equations continue to be the best available equations for estimating peak flows for basin areas greater than 12 mi2. New equations presented here are based on streamflow records at 40 U.S. Geological Survey streamgages with a minimum of 10 years of recorded peak flows between 1963 and 2012. Ordinary least-squares regression techniques were used to determine the best explanatory variables for the regression equations. Traditional map-based explanatory variables were compared to variables requiring field measurements. Two field-based variables—culvert rust lines and bankfull channel widths—either were not commonly found or did not explain enough of the variability in the peak flows to warrant inclusion in the equations. The best explanatory variables were drainage area and percent basin wetlands; values for these variables were determined with a geographic information system. Generalized least-squares regression was used with these two variables to determine the equation coefficients and estimates of accuracy for the final equations.

The 2009 A(H1N1) influenza pandemic in the French Armed Forces: epidemiological surveillance and operational management.

PubMed

Pohl, Jean-Baptiste; Mayet, Aurélie; Bédubourg, Gabriel; Duron, Sandrine; Michel, Rémy; Deparis, Xavier; Rapp, Christophe; Godart, Patrick; Migliani, René; Meynard, Jean-Baptiste

2014-02-01

The main objective of this study was to evaluate the contribution of a newly implemented daily surveillance system to the management of the 2009 A(H1N1) influenza pandemic by the military decision-makers at different levels in the French Department of Defence. The study sample included all medical advisors in the Ministry of Defence and the French Armed Forces Staff and also the members of the specific committee dedicated to flu pandemic control. The variables studied were mental representation of epidemiology, relevance, usefulness, and real-time use of surveillance data using quantitative questionnaires and qualitative face-to-face semistructured interviews. Among the risk managers of the flu pandemic in the Armed Forces, 84% responded. The data generated by epidemiological surveillance were considered relevant and useful, and were reported as effectively used. On the basis of the information produced, concrete actions were planned and implemented in the French Armed Forces. In a pandemic situation involving low mortality, the daily monitoring of the disease did not target public health issues, but it was mainly used to assess the availability of the Armed Forces in real time. For the military staff, epidemiological surveillance represents an essential information tool for the conduct of operations. Reprint & Copyright © 2014 Association of Military Surgeons of the U.S.

CSI 2264: Simultaneous optical and X-ray variability in pre-main sequence stars. I. Time resolved X-ray spectral analysis during optical dips and accretion bursts in stars with disks

NASA Astrophysics Data System (ADS)

Guarcello, M. G.; Flaccomio, E.; Micela, G.; Argiroffi, C.; Sciortino, S.; Venuti, L.; Stauffer, J.; Rebull, L.; Cody, A. M.

2017-06-01

Context. Pre-main sequence stars are variable sources. The main mechanisms responsible for their variability are variable extinction, unsteady accretion, and rotational modulation of both hot and dark photospheric spots and X-ray-active regions. In stars with disks, this variability is related to the morphology of the inner circumstellar region (≤0.1 AU) and that of the photosphere and corona, all impossible to be spatially resolved with present-day techniques. This has been the main motivation for the Coordinated Synoptic Investigation of NGC 2264, a set of simultaneous observations of NGC 2264 with 15 different telescopes. Aims: In this paper, we focus on the stars with disks. We analyze the X-ray spectral properties extracted during optical bursts and dips in order to unveil the nature of these phenomena. Stars without disks are studied in a companion paper. Methods: We analyze simultaneous CoRoT and Chandra/ACIS-I observations to search for coherent optical and X-ray flux variability in stars with disks. Then, stars are analyzed in two different samples. In stars with variable extinction, we look for a simultaneous increase of optical extinction and X-ray absorption during the optical dips; in stars with accretion bursts, we search for soft X-ray emission and increasing X-ray absorption during the bursts. Results: We find evidence for coherent optical and X-ray flux variability among the stars with variable extinction. In 9 of the 24 stars with optical dips, we observe a simultaneous increase of X-ray absorption and optical extinction. In seven dips, it is possible to calculate the NH/AV ratio in order to infer the composition of the obscuring material. In 5 of the 20 stars with optical accretion bursts, we observe increasing soft X-ray emission during the bursts that we associate to the emission of accreting gas. It is not surprising that these properties are not observed in all the stars with dips and bursts, since favorable geometric configurations are required. Conclusions: The observed variable absorption during the dips is mainly due to dust-free material in accretion streams. In stars with accretion bursts, we observe, on average, a larger soft X-ray spectral component not observed in non-accreting stars.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Belu, Radian; Koracin, Darko

The main objective of the study was to investigate spatial and temporal characteristics of the wind speed and direction in complex terrain that are relevant to wind energy assessment and development, as well as to wind energy system operation, management, and grid integration. Wind data from five tall meteorological towers located in Western Nevada, USA, operated from August 2003 to March 2008, used in the analysis. The multiannual average wind speeds did not show significant increased trend with increasing elevation, while the turbulence intensity slowly decreased with an increase were the average wind speed. The wind speed and direction weremore » modeled using the Weibull and the von Mises distribution functions. The correlations show a strong coherence between the wind speed and direction with slowly decreasing amplitude of the multiday periodicity with increasing lag periods. The spectral analysis shows significant annual periodicity with similar characteristics at all locations. The relatively high correlations between the towers and small range of the computed turbulence intensity indicate that wind variability is dominated by the regional synoptic processes. Knowledge and information about daily, seasonal, and annual wind periodicities are very important for wind energy resource assessment, wind power plant operation, management, and grid integration.« less

Maximizing the performance of a multiple-stage variable-throat venturi scrubber for particle collection

NASA Astrophysics Data System (ADS)

Muir, D. M.; Akeredolu, F.

The high collection efficiencies that are required nowadays to meet the stricter pollution control standards necessitate the use of high-energy scrubbers, such as the venturi scrubber, for the arrestment of fine particulate matter from exhaust gas streams. To achieve more energy-efficient particle collection, several venturi stages may be used in series. This paper is principally a theoretical investigation of the performance of a multiple-stage venturi scrubber, the main objective of the study being to establish the best venturi design configuration for any given set of operating conditions. A mathematical model is used to predict collection efficiency vs pressure drop relationships for particle sizes in the range 0.2-5.0 μm for one-, two-, three- and four-stage scrubbers. The theoretical predictions are borne out qualitatively by experimental work. The paper shows that the three-stage venturi produces the highest collection efficiencies over the normal operating range except for the collection of very fine particles at low pressure drops, when the single-stage venturi is best. The significant improvement in performance achieved by the three-stage venturi when compared with conventional single-stage operation increases as both the particle size and system pressure drop increase.

The hit problem for symmetric polynomials over the Steenrod algebra

NASA Astrophysics Data System (ADS)

Janfada, A. S.; Wood, R. M. W.

2002-09-01

We cite [18] for references to work on the hit problem for the polynomial algebra P(n) = [open face F]2[x1, ;…, xn] = [oplus B: plus sign in circle]d[gt-or-equal, slanted]0 Pd(n), viewed as a graded left module over the Steenrod algebra [script A] at the prime 2. The grading is by the homogeneous polynomials Pd(n) of degree d in the n variables x1, …, xn of grading 1. The present article investigates the hit problem for the [script A]-submodule of symmetric polynomials B(n) = P(n)[sum L: summation operator]n , where [sum L: summation operator]n denotes the symmetric group on n letters acting on the right of P(n). Among the main results is the symmetric version of the well-known Peterson conjecture. For a positive integer d, let [mu](d) denote the smallest value of k for which d = [sum L: summation operator]ki=1(2[lambda]i[minus sign]1), where [lambda]i [gt-or-equal, slanted] 0.

Autonomous Aerobraking Using Thermal Response Surface Analysis

NASA Technical Reports Server (NTRS)

Prince, Jill L.; Dec, John A.; Tolson, Robert H.

2007-01-01

Aerobraking is a proven method of significantly increasing the science payload that can be placed into low Mars orbits when compared to an all propulsive capture. However, the aerobraking phase is long and has mission cost and risk implications. The main cost benefit is that aerobraking permits the use of a smaller and cheaper launch vehicle, but additional operational costs are incurred during the long aerobraking phase. Risk is increased due to the repeated thermal loading of spacecraft components and the multiple attitude and propulsive maneuvers required for successful aerobraking. Both the cost and risk burdens can be significantly reduced by automating the aerobraking operations phase. All of the previous Mars orbiter missions that have utilized aerobraking have increasingly relied on onboard calculations during aerobraking. Even though the temperature of spacecraft components has been the limiting factor, operational methods have relied on using a surrogate variable for mission control. This paper describes several methods, based directly on spacecraft component maximum temperature, for autonomously predicting the subsequent aerobraking orbits and prescribing apoapsis propulsive maneuvers to maintain the spacecraft within specified temperature limits. Specifically, this paper describes the use of thermal response surface analysis in predicting the temperature of the spacecraft components and the corresponding uncertainty in this temperature prediction.

Adaptive multiresolution modeling of groundwater flow in heterogeneous porous media

NASA Astrophysics Data System (ADS)

Malenica, Luka; Gotovac, Hrvoje; Srzic, Veljko; Andric, Ivo

2016-04-01

Proposed methodology was originally developed by our scientific team in Split who designed multiresolution approach for analyzing flow and transport processes in highly heterogeneous porous media. The main properties of the adaptive Fup multi-resolution approach are: 1) computational capabilities of Fup basis functions with compact support capable to resolve all spatial and temporal scales, 2) multi-resolution presentation of heterogeneity as well as all other input and output variables, 3) accurate, adaptive and efficient strategy and 4) semi-analytical properties which increase our understanding of usually complex flow and transport processes in porous media. The main computational idea behind this approach is to separately find the minimum number of basis functions and resolution levels necessary to describe each flow and transport variable with the desired accuracy on a particular adaptive grid. Therefore, each variable is separately analyzed, and the adaptive and multi-scale nature of the methodology enables not only computational efficiency and accuracy, but it also describes subsurface processes closely related to their understood physical interpretation. The methodology inherently supports a mesh-free procedure, avoiding the classical numerical integration, and yields continuous velocity and flux fields, which is vitally important for flow and transport simulations. In this paper, we will show recent improvements within the proposed methodology. Since "state of the art" multiresolution approach usually uses method of lines and only spatial adaptive procedure, temporal approximation was rarely considered as a multiscale. Therefore, novel adaptive implicit Fup integration scheme is developed, resolving all time scales within each global time step. It means that algorithm uses smaller time steps only in lines where solution changes are intensive. Application of Fup basis functions enables continuous time approximation, simple interpolation calculations across different temporal lines and local time stepping control. Critical aspect of time integration accuracy is construction of spatial stencil due to accurate calculation of spatial derivatives. Since common approach applied for wavelets and splines uses a finite difference operator, we developed here collocation one including solution values and differential operator. In this way, new improved algorithm is adaptive in space and time enabling accurate solution for groundwater flow problems, especially in highly heterogeneous porous media with large lnK variances and different correlation length scales. In addition, differences between collocation and finite volume approaches are discussed. Finally, results show application of methodology to the groundwater flow problems in highly heterogeneous confined and unconfined aquifers.

Perturbing engine performance measurements to determine optimal engine control settings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Li; Lee, Donghoon; Yilmaz, Hakan

Methods and systems for optimizing a performance of a vehicle engine are provided. The method includes determining an initial value for a first engine control parameter based on one or more detected operating conditions of the vehicle engine, determining a value of an engine performance variable, and artificially perturbing the determined value of the engine performance variable. The initial value for the first engine control parameter is then adjusted based on the perturbed engine performance variable causing the engine performance variable to approach a target engine performance variable. Operation of the vehicle engine is controlled based on the adjusted initialmore » value for the first engine control parameter. These acts are repeated until the engine performance variable approaches the target engine performance variable.« less

Enhancing the Remote Variable Operations in NPSS/CCDK

NASA Technical Reports Server (NTRS)

Sang, Janche; Follen, Gregory; Kim, Chan; Lopez, Isaac; Townsend, Scott

2001-01-01

Many scientific applications in aerodynamics and solid mechanics are written in Fortran. Refitting these legacy Fortran codes with distributed objects can increase the code reusability. The remote variable scheme provided in NPSS/CCDK helps programmers easily migrate the Fortran codes towards a client-server platform. This scheme gives the client the capability of accessing the variables at the server site. In this paper, we review and enhance the remote variable scheme by using the operator overloading features in C++. The enhancement enables NPSS programmers to use remote variables in much the same way as traditional variables. The remote variable scheme adopts the lazy update approach and the prefetch method. The design strategies and implementation techniques are described in details. Preliminary performance evaluation shows that communication overhead can be greatly reduced.

Sleeve Gastrectomy: Correlation of Long-Term Results with Remnant Morphology and Eating Disorders.

PubMed

Tassinari, Daniele; Berta, Rossana D; Nannipieri, Monica; Giusti, Patrizia; Di Paolo, Luca; Guarino, Daniela; Anselmino, Marco

2017-11-01

Remnant dimension is considered one of the crucial elements determining the success of sleeve gastrectomy (SG), and dilation of the gastric fundus is often believed to be the main cause of failure. The main outcome of this study is to find correlations between remnant morphology in the immediate post-operative stage, its dilation in years, and the long-term results. The second purpose aims to correlate preoperative eating disorders, taste alteration, hunger perception, and early satiety with post-SG results. Remnant morphology was evaluated, in the immediate post-operative stage and over the years (≥2 years), through X-ray of the oesophagus-stomach-duodenum calculating the surface in anteroposterior (AP) and right anterior oblique projection (RAO). Presurgery diagnosis of eating disorders and their evaluation through "Eating Disorder Inventory-3" (EDI3) during follow-up were performed. Change in taste perception, sense of appetite, and early satiety were evaluated. Patients were divided into two groups: "failed SGs (EWL<50%) and "efficient SGs" (EWL >50%). There were a total of 50 patients (37 F, 13 M), with mean age 52 years, preoperative weight 131 ± 21.8 kg, and BMI 47.4 ± 6.8 kg/m 2 . Post-operative remnant mean dimensions overlapped between the two groups. On a long-term basis, an increase of 57.2 and 48.4% was documented in the AP and RAO areas respectively. In "failed" SGs, dilation was significantly superior to "efficient" SGs (AP area 70.2 vs 46.1%; RAO area 59.3 vs 39%; body width 102% vs 41.7%). Preoperative eating disorders were more present in efficient SGs than in failed SGs with the exception of sweet eating. There were no significant changes to taste perception during follow-up. Fifty-two percent of efficient SGs vs 26% of failed SGs reported a persistent lack of sense of hunger; similarly, 92.5 vs 78% declared the persistence of a sense of early satiety. The two groups did not statistically differ as far as all the variables of the EDI3 are concerned. On a long-term basis, the remnant mean dilation is around 50% compared to the immediate post-operative stage but failed SGs showed larger remnant dilation than efficient SGs and, in percentage, the more dilated portion is the body of the stomach. As far as all the EDI3 variables obtained are concerned, the two groups did not statistically differ. Of all eating disorders, sweet eating seems to be weakly connected to SG failure.

A one dimensional moving bed biofilm reactor model for nitrification of municipal wastewaters.

PubMed

Barry, Ugo; Choubert, Jean-Marc; Canler, Jean-Pierre; Pétrimaux, Olivier; Héduit, Alain; Lessard, Paul

2017-08-01

This work presents a one-dimensional model of a moving bed bioreactor (MBBR) process designed for the removal of nitrogen from raw wastewaters. A comprehensive experimental strategy was deployed at a semi-industrial pilot-scale plant fed with a municipal wastewater operated at 10-12 °C, and surface loading rates of 1-2 g filtered COD/m 2 d and 0.4-0.55 g NH 4 -N/m 2 d. Data were collected on influent/effluent composition, and on measurement of key variables or parameters (biofilm mass and maximal thickness, thickness of the limit liquid layer, maximal nitrification rate, oxygen mass transfer coefficient). Based on time-course variations in these variables, the MBBR model was calibrated at two time-scales and magnitudes of dynamic conditions, i.e., short-term (4 days) calibration under dynamic conditions and long-term (33 days) calibration, and for three types of carriers. A set of parameters suitable for the conditions was proposed, and the calibrated parameter set is able to simulate the time-course change of nitrogen forms in the effluent of the MBBR tanks, under the tested operated conditions. Parameters linked to diffusion had a strong influence on how robustly the model is able to accurately reproduce time-course changes in effluent quality. Then the model was used to optimize the operations of MBBR layout. It was shown that the main optimization track consists of the limitation of the aeration supply without changing the overall performance of the process. Further work would investigate the influence of the hydrodynamic conditions onto the thickness of the limit liquid layer and the "apparent" diffusion coefficient in the biofilm parameters.

Comparison of dissection with harmonic scalpel and conventional bipolar electrocautery in deep inferior epigastric perforator flap surgery: A consecutive cohort study.

PubMed

Lee, Yoon Jae; Kim, Hak Young; Han, Hyun Ho; Moon, Suk-Ho; Byeon, Jun Hee; Rhie, Jong Won; Ahn, Sang Tae; Oh, Deuk Young

2017-02-01

Reduced tissue damage is a theoretical advantage of using an ultrasonic harmonic scalpel. We hypothesized that the harmonic scalpel would outperform electrocautery in deep inferior epigastric perforator flap surgery, possibly resulting in a shorter operative time and reduced postoperative drainage and pain. Between January and August 2015, 24 consecutive patients were assigned to immediate deep inferior epigastric perforator flap elevation (12 for bipolar electrocautery and 12 for harmonic scalpel). The main outcome variables were total operative time, flap elevation time (starting from the fascia incision), and drainage volume. We compared the number of perforators isolated and the Moon and Taylor classification of the pedicle. Data were tested for normality using the Kolmogorov-Smirnov test before analysis. Continuous variables were compared by Wilcoxon rank-sum test. Data were analyzed using the statistical software SAS, version 9.3 (SAS Institute, Cary, NC, USA). Both groups were comparable with respect to clinical characteristics (mean age, body mass index, and flap weights). There was a statistically significant difference in the operative time between dissection with the harmonic scalpel and electrocautery (305.2 vs. 380.3 min, respectively, p = 0.002). The flap elevation time was reduced, particularly when using the harmonic scalpel where its usage seems crucial for dissecting deep inferior epigastric perforators (59.8 vs. 145.9 min, respectively, p < 0.0001). No statistical difference was observed in the drainage volume and length of hospital stay between the groups. We conclude that the harmonic scalpel may be more reliable and efficient as an alternative to electrocautery. Copyright © 2016 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Development of pre pre-driver amplifier stage for generator of SST-1 ICRH system

NASA Astrophysics Data System (ADS)

Kumar, Sunil; Sinh Makwana, Azad; Srinivas, Y. S. S.; Kulkarni, S. V.; ICRH-RF Group

2010-02-01

The Ion Cyclotron Resonance Heating (ICRH) system for SST1 consists mainly of the cwrf power generator to deliver 1.5MW for 1000sec duration at the frequencies 22.8, 24.3 and 45.6±1MHz, the transmission line and the antenna. This is planned to develop a independent and dedicated cwrf generator that consists of a oscillator, buffer, rf switch, modulator, rf attenuator, directional coupler, three stage solid state low power amplifier and four stage triode & tetrode based high power amplifier with specific performance at 45.6±1MHz including frequencies 22.8 and 24.3±1MHz. The pre pre-driver high power amplifier stage is fabricated about triode 3CX3000A7. The tube has sufficient margin in terms of plate dissipation and grid dissipation that makes it suitable to withstand momentarily load mismatch and to upgrade the source in terms of output power later. This indigenously developed amplifier is integrated inside a radiation resistant rack with all required biasing power supplies, cooling blower, controls, monitors and interlocks for manual or remote control operation. This grounded grid mode amplifier will be operated at plate with 3.8KV/ 800mA in class AB for 1.8KW cwrf output power rating. The input circuit is broadband and the output circuit is tunable with slide variable inductor and a vacuum variable capacitor in the frequency range of 22.8 to 45.6MHz. It is designed for a gain of about 12dB, fabrication completed and undergoing cwrf power testing. This paper presents specifications, design criteria, circuit used, operating parameters, tests conducted and the results obtained.

Improving seasonal forecasts of hydroclimatic variables through the state of multiple large-scale climate signals

NASA Astrophysics Data System (ADS)

Castelletti, A.; Giuliani, M.; Block, P. J.

2017-12-01

Increasingly uncertain hydrologic regimes combined with more frequent and intense extreme events are challenging water systems management worldwide, emphasizing the need of accurate medium- to long-term predictions to timely prompt anticipatory operations. Despite modern forecasts are skillful over short lead time (from hours to days), predictability generally tends to decrease on longer lead times. Global climate teleconnection, such as El Niño Southern Oscillation (ENSO), may contribute in extending forecast lead times. However, ENSO teleconnection is well defined in some locations, such as Western USA and Australia, while there is no consensus on how it can be detected and used in other regions, particularly in Europe, Africa, and Asia. In this work, we generalize the Niño Index Phase Analysis (NIPA) framework by contributing the Multi Variate Niño Index Phase Analysis (MV-NIPA), which allows capturing the state of multiple large-scale climate signals (i.e. ENSO, North Atlantic Oscillation, Pacific Decadal Oscillation, Atlantic Multi-decadal Oscillation, Indian Ocean Dipole) to forecast hydroclimatic variables on a seasonal time scale. Specifically, our approach distinguishes the different phases of the considered climate signals and, for each phase, identifies relevant anomalies in Sea Surface Temperature (SST) that influence the local hydrologic conditions. The potential of the MV-NIPA framework is demonstrated through an application to the Lake Como system, a regulated lake in northern Italy which is mainly operated for flood control and irrigation supply. Numerical results show high correlations between seasonal SST values and one season-ahead precipitation in the Lake Como basin. The skill of the resulting MV-NIPA forecast outperforms the one of ECMWF products. This information represents a valuable contribution to partially anticipate the summer water availability, especially during drought events, ultimately supporting the improvement of the Lake Como operations.

Is Reaction Time Variability in ADHD Mainly at Low Frequencies?

ERIC Educational Resources Information Center

Karalunas, Sarah L.; Huang-Pollock, Cynthia L.; Nigg, Joel T.

2013-01-01

Background: Intraindividual variability in reaction times (RT variability) has garnered increasing interest as an indicator of cognitive and neurobiological dysfunction in children with attention deficit hyperactivity disorder (ADHD). Recent theory and research has emphasized specific low-frequency patterns of RT variability. However, whether…

The motivating operation and negatively reinforced problem behavior: a systematic review.

PubMed

Langthorne, Paul; McGill, Peter; Oliver, Chris

2014-01-01

The concept of motivational operations exerts an increasing influence on the understanding and assessment of problem behavior in people with intellectual and developmental disability. In this systematic review of 59 methodologically robust studies of the influence of motivational operations in negative reinforcement paradigms in this population, we identify themes related to situational and biological variables that have implications for assessment, intervention, and further research. There is now good evidence that motivational operations of differing origins influence negatively reinforced problem behavior, and that these might be subject to manipulation to facilitate favorable outcomes. There is also good evidence that some biological variables warrant consideration in assessment procedures as they predispose the person's behavior to be influenced by specific motivational operations. The implications for assessment and intervention are made explicit with reference to variables that are open to manipulation or that require further research and conceptualization within causal models.

Identifying socioeconomic, epidemiological and operational scenarios for tuberculosis control in Brazil: an ecological study.

PubMed

Pelissari, Daniele Maria; Rocha, Marli Souza; Bartholomay, Patricia; Sanchez, Mauro Niskier; Duarte, Elisabeth Carmen; Arakaki-Sanchez, Denise; Dantas, Cíntia Oliveira; Jacobs, Marina Gasino; Andrade, Kleydson Bonfim; Codenotti, Stefano Barbosa; Andrade, Elaine Silva Nascimento; Araújo, Wildo Navegantes de; Costa, Fernanda Dockhorn; Ramalho, Walter Massa; Diaz-Quijano, Fredi Alexander

2018-06-06

To identify scenarios based on socioeconomic, epidemiological and operational healthcare factors associated with tuberculosis incidence in Brazil. Ecological study. The study was based on new patients with tuberculosis and epidemiological/operational variables of the disease from the Brazilian National Information System for Notifiable Diseases and the Mortality Information System. We also analysed socioeconomic and demographic variables. The units of analysis were the Brazilian municipalities, which in 2015 numbered 5570 but 5 were excluded due to the absence of socioeconomic information. Tuberculosis incidence rate in 2015. We evaluated as independent variables the socioeconomic (2010), epidemiological and operational healthcare indicators of tuberculosis (2014 or 2015) using negative binomial regression. Municipalities were clustered by the k-means method considering the variables identified in multiple regression models. We identified two clusters according to socioeconomic variables associated with the tuberculosis incidence rate (unemployment rate and household crowding): a higher socioeconomic scenario (n=3482 municipalities) with a mean tuberculosis incidence rate of 16.3/100 000 population and a lower socioeconomic scenario (2083 municipalities) with a mean tuberculosis incidence rate of 22.1/100 000 population. In a second stage of clusterisation, we defined four subgroups in each of the socioeconomic scenarios using epidemiological and operational variables such as tuberculosis mortality rate, AIDS case detection rate and proportion of vulnerable population among patients with tuberculosis. Some of the subscenarios identified were characterised by fragility in their information systems, while others were characterised by the concentration of tuberculosis cases in key populations. Clustering municipalities in scenarios allowed us to classify them according to the socioeconomic, epidemiological and operational variables associated with tuberculosis risk. This classification can support targeted evidence-based decisions such as monitoring data quality for improving the information system or establishing integrative social protective policies for key populations. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Comparative genomics of wild type yeast strains unveils important genome diversity

PubMed Central

Carreto, Laura; Eiriz, Maria F; Gomes, Ana C; Pereira, Patrícia M; Schuller, Dorit; Santos, Manuel AS

2008-01-01

Background Genome variability generates phenotypic heterogeneity and is of relevance for adaptation to environmental change, but the extent of such variability in natural populations is still poorly understood. For example, selected Saccharomyces cerevisiae strains are variable at the ploidy level, have gene amplifications, changes in chromosome copy number, and gross chromosomal rearrangements. This suggests that genome plasticity provides important genetic diversity upon which natural selection mechanisms can operate. Results In this study, we have used wild-type S. cerevisiae (yeast) strains to investigate genome variation in natural and artificial environments. We have used comparative genome hybridization on array (aCGH) to characterize the genome variability of 16 yeast strains, of laboratory and commercial origin, isolated from vineyards and wine cellars, and from opportunistic human infections. Interestingly, sub-telomeric instability was associated with the clinical phenotype, while Ty element insertion regions determined genomic differences of natural wine fermentation strains. Copy number depletion of ASP3 and YRF1 genes was found in all wild-type strains. Other gene families involved in transmembrane transport, sugar and alcohol metabolism or drug resistance had copy number changes, which also distinguished wine from clinical isolates. Conclusion We have isolated and genotyped more than 1000 yeast strains from natural environments and carried out an aCGH analysis of 16 strains representative of distinct genotype clusters. Important genomic variability was identified between these strains, in particular in sub-telomeric regions and in Ty-element insertion sites, suggesting that this type of genome variability is the main source of genetic diversity in natural populations of yeast. The data highlights the usefulness of yeast as a model system to unravel intraspecific natural genome diversity and to elucidate how natural selection shapes the yeast genome. PMID:18983662

EXAMINING THE TEMPORAL VARIABILITY OF AMMONIA AND NITRIC OXIDE EMISSIONS FROM AGRICULTURAL PROCESSES

EPA Science Inventory

This paper examines the temporal variability of airborne emissions of ammonia from livestock operations and fertilizer application and nitric oxide from soils. In the United States, the livestock operations and fertilizer categories comprise the majority of the ammonia emissions...

A Reserve-based Method for Mitigating the Impact of Renewable Energy

NASA Astrophysics Data System (ADS)

Krad, Ibrahim

The fundamental operating paradigm of today's power systems is undergoing a significant shift. This is partially motivated by the increased desire for incorporating variable renewable energy resources into generation portfolios. While these generating technologies offer clean energy at zero marginal cost, i.e. no fuel costs, they also offer unique operating challenges for system operators. Perhaps the biggest operating challenge these resources introduce is accommodating their intermittent fuel source availability. For this reason, these generators increase the system-wide variability and uncertainty. As a result, system operators are revisiting traditional operating strategies to more efficiently incorporate these generation resources to maximize the benefit they provide while minimizing the challenges they introduce. One way system operators have accounted for system variability and uncertainty is through the use of operating reserves. Operating reserves can be simplified as excess capacity kept online during real time operations to help accommodate unforeseen fluctuations in demand. With new generation resources, a new class of operating reserves has emerged that is generally known as flexibility, or ramping, reserves. This new reserve class is meant to better position systems to mitigate severe ramping in the net load profile. The best way to define this new requirement is still under investigation. Typical requirement definitions focus on the additional uncertainty introduced by variable generation and there is room for improvement regarding explicit consideration for the variability they introduce. An exogenous reserve modification method is introduced in this report that can improve system reliability with minimal impacts on total system wide production costs. Another potential solution to this problem is to formulate the problem as a stochastic programming problem. The unit commitment and economic dispatch problems are typically formulated as deterministic problems due to fast solution times and the solutions being sufficient for operations. Improvements in technical computing hardware have reignited interest in stochastic modeling. The variability of wind and solar naturally lends itself to stochastic modeling. The use of explicit reserve requirements in stochastic models is an area of interest for power system researchers. This report introduces a new reserve modification implementation based on previous results to be used in a stochastic modeling framework. With technological improvements in distributed generation technologies, microgrids are currently being researched and implemented. Microgrids are small power systems that have the ability to serve their demand with their own generation resources and may have a connection to a larger power system. As battery technologies improve, they are becoming a more viable option in these distributed power systems and research is necessary to determine the most efficient way to utilize them. This report will investigate several unique operating strategies for batteries in small power systems and analyze their benefits. These new operating strategies will help reduce operating costs and improve system reliability.

Analysis of the energy efficiency of an integrated ethanol processor for PEM fuel cell systems

NASA Astrophysics Data System (ADS)

Francesconi, Javier A.; Mussati, Miguel C.; Mato, Roberto O.; Aguirre, Pio A.

The aim of this work is to investigate the energy integration and to determine the maximum efficiency of an ethanol processor for hydrogen production and fuel cell operation. Ethanol, which can be produced from renewable feedstocks or agriculture residues, is an attractive option as feed to a fuel processor. The fuel processor investigated is based on steam reforming, followed by high- and low-temperature shift reactors and preferential oxidation, which are coupled to a polymeric fuel cell. Applying simulation techniques and using thermodynamic models the performance of the complete system has been evaluated for a variety of operating conditions and possible reforming reactions pathways. These models involve mass and energy balances, chemical equilibrium and feasible heat transfer conditions (Δ T min). The main operating variables were determined for those conditions. The endothermic nature of the reformer has a significant effect on the overall system efficiency. The highest energy consumption is demanded by the reforming reactor, the evaporator and re-heater operations. To obtain an efficient integration, the heat exchanged between the reformer outgoing streams of higher thermal level (reforming and combustion gases) and the feed stream should be maximized. Another process variable that affects the process efficiency is the water-to-fuel ratio fed to the reformer. Large amounts of water involve large heat exchangers and the associated heat losses. A net electric efficiency around 35% was calculated based on the ethanol HHV. The responsibilities for the remaining 65% are: dissipation as heat in the PEMFC cooling system (38%), energy in the flue gases (10%) and irreversibilities in compression and expansion of gases. In addition, it has been possible to determine the self-sufficient limit conditions, and to analyze the effect on the net efficiency of the input temperatures of the clean-up system reactors, combustion preheating, expander unit and crude ethanol as fuel.

Statistical strategy for anisotropic adventitia modelling in IVUS.

PubMed

Gil, Debora; Hernández, Aura; Rodriguez, Oriol; Mauri, Josepa; Radeva, Petia

2006-06-01

Vessel plaque assessment by analysis of intravascular ultrasound sequences is a useful tool for cardiac disease diagnosis and intervention. Manual detection of luminal (inner) and media-adventitia (external) vessel borders is the main activity of physicians in the process of lumen narrowing (plaque) quantification. Difficult definition of vessel border descriptors, as well as, shades, artifacts, and blurred signal response due to ultrasound physical properties trouble automated adventitia segmentation. In order to efficiently approach such a complex problem, we propose blending advanced anisotropic filtering operators and statistical classification techniques into a vessel border modelling strategy. Our systematic statistical analysis shows that the reported adventitia detection achieves an accuracy in the range of interobserver variability regardless of plaque nature, vessel geometry, and incomplete vessel borders.

Compact E x B mass separator for heavy ion beams.

PubMed

Wada, M; Hashino, T; Hirata, F; Kasuya, T; Sakamoto, Y; Nishiura, M

2008-02-01

A compact E x B mass separator that deflects beam by 30 degrees has been designed and built to prove its principle of operation. The main part of the separator is contained in a shielding box of 11 cm long, 9 cm wide, and 1.5 cm high. An electromagnet of 7 cm pole diameter produced variable magnetic field in the mass separation region instead of a couple of permanent magnets which is to be used in the final design. The experimental result agreed well with the theoretical prediction, and larger mass ions is bent with less magnetic field with the aid of the deflection electric field. The reduction in resolving power for mass separation due to the deflection electric field has been investigated experimentally.

Hybrid thrusters and reaction wheels strategy for large angle rapid reorientation with high precision

NASA Astrophysics Data System (ADS)

Ye, Dong; Sun, Zhaowei; Wu, Shunan

2012-08-01

The quaternion-based, high precision, large angle rapid reorientation of rigid spacecraft is the main problem investigated in this study. The operation is accomplished via a hybrid thrusters and reaction wheels strategy where thrusters are engaged in providing a primary maneuver torque in open loop, while reaction wheels provide fine control torque to achieve high precision in closed-loop control. The inaccuracy of thrusters is handled by a variable structure control (VSC). In addition, a signum function is mixed in the switching surface in VSC to produce a maneuver to the reference attitude trajectory in a shortest distance. Detailed proofs and numerical simulation examples are presented to illustrate all the technical aspects of this work.

Noise emission of civil and military aero-engines. Sources of generation and measures for attenuation

NASA Astrophysics Data System (ADS)

Grieb, H.; Heinig, K.

1986-09-01

It is shown that noise reduction on high bypass ratio turbofans for civil airliners is well established. The noise levels achieved meet the internationally agreed regulations (FAR 36). The same holds true for large military transport aircraft. Helicopter noise is caused essentially by the main and tail rotors. Noise reduction on afterburner and dry engines for combat and strike aircraft, which represent the major noise annoyance to the public, is very difficult because: high specific thrust is mandatory for aircraft performance and effectiveness; jet noise with and without afterburning is predominant; and the design of the reheat section and final (variable) nozzle in practice precludes the application of known concepts for jet noise attenuation in dry and reheated operation.

Radiation effect on rocket engine performance

NASA Technical Reports Server (NTRS)

Chiu, Huei-Huang; Kross, K. W.; Krebsbach, A. N.

1990-01-01

Critical problem areas involving the effect of radiation on the combustion of bipropellants are addressed by formulating a universal scaling law in combination with a radiation-enhanced vaporization combustion model. Numerical algorithms are developed and data pertaining to the Variable Thrust Engine (VTE) and the Space Shuttle Main Engine (SSME) are used to conduct parametric sensitivity studies to predict the principal intercoupling effects of radiation. The analysis reveals that low-enthalpy engines, such as the VTE, are vulnerable to a substantial performance setback due to radiative loss, whereas the performance of high-enthalpy engines such as the SSME are hardly affected over a broad range of engine operation. Combustion enhancement by radiative heating of the propellant has a significant impact on propellants with high absorptivity.

The theory and method of variable frequency directional seismic wave under the complex geologic conditions

NASA Astrophysics Data System (ADS)

Jiang, T.; Yue, Y.

2017-12-01

It is well known that the mono-frequency directional seismic wave technology can concentrate seismic waves into a beam. However, little work on the method and effect of variable frequency directional seismic wave under complex geological conditions have been done .We studied the variable frequency directional wave theory in several aspects. Firstly, we studied the relation between directional parameters and the direction of the main beam. Secondly, we analyzed the parameters that affect the beam width of main beam significantly, such as spacing of vibrator, wavelet dominant frequency, and number of vibrator. In addition, we will study different characteristics of variable frequency directional seismic wave in typical velocity models. In order to examine the propagation characteristics of directional seismic wave, we designed appropriate parameters according to the character of direction parameters, which is capable to enhance the energy of the main beam direction. Further study on directional seismic wave was discussed in the viewpoint of power spectral. The results indicate that the energy intensity of main beam direction increased 2 to 6 times for a multi-ore body velocity model. It showed us that the variable frequency directional seismic technology provided an effective way to strengthen the target signals under complex geological conditions. For concave interface model, we introduced complicated directional seismic technology which supports multiple main beams to obtain high quality data. Finally, we applied the 9-element variable frequency directional seismic wave technology to process the raw data acquired in a oil-shale exploration area. The results show that the depth of exploration increased 4 times with directional seismic wave method. Based on the above analysis, we draw the conclusion that the variable frequency directional seismic wave technology can improve the target signals of different geologic conditions and increase exploration depth with little cost. Due to inconvenience of hydraulic vibrators in complicated surface area, we suggest that the combination of high frequency portable vibrator and variable frequency directional seismic wave method is an alternative technology to increase depth of exploration or prospecting.

Variability of residual stresses and superposition effect in multipass grinding of high-carbon high-chromium steel

NASA Astrophysics Data System (ADS)

Karabelchtchikova, Olga; Rivero, Iris V.

2005-02-01

The distribution of residual stresses (RS) and surface integrity generated in heat treatment and subsequent multipass grinding was investigated in this experimental study to examine the source of variability and the nature of the interactions of the experimental factors. A nested experimental design was implemented to (a) compare the sources of the RS variability, (b) to examine RS distribution and tensile peak location due to experimental factors, and (c) to analyze the superposition relationship in the RS distribution due to multipass grinding technique. To characterize the material responses, several techniques were used, including microstructural analysis, hardness-toughness and roughness examinations, and retained austenite and RS measurements using x-ray diffraction. The causality of the RS was explained through the strong correlation of the surface integrity characteristics and RS patterns. The main sources of variation were the depth of the RS distribution and the multipass grinding technique. The grinding effect on the RS was statistically significant; however, it was mostly predetermined by the preexisting RS induced in heat treatment. Regardless of the preceding treatments, the effect of the multipass grinding technique exhibited similar RS patterns, which suggests the existence of the superposition relationship and orthogonal memory between the passes of the grinding operation.

Control Law Design for Propofol Infusion to Regulate Depth of Hypnosis: A Nonlinear Control Strategy

PubMed Central

Khaqan, Ali; Bilal, Muhammad; Ilyas, Muhammad; Ijaz, Bilal; Ali Riaz, Raja

2016-01-01

Maintaining the depth of hypnosis (DOH) during surgery is one of the major objectives of anesthesia infusion system. Continuous administration of Propofol infusion during surgical procedures is essential but increases the undue load of an anesthetist in operating room working in a multitasking setup. Manual and target controlled infusion (TCI) systems are not good at handling instabilities like blood pressure changes and heart rate variability arising due to interpatient variability. Patient safety, large interindividual variability, and less postoperative effects are the main factors to motivate automation in anesthesia. The idea of automated system for Propofol infusion excites the control engineers to come up with a more sophisticated and safe system that handles optimum delivery of drug during surgery and avoids postoperative effects. In contrast to most of the investigations with linear control strategies, the originality of this research work lies in employing a nonlinear control technique, backstepping, to track the desired hypnosis level of patients during surgery. This effort is envisioned to unleash the true capabilities of this nonlinear control technique for anesthesia systems used today in biomedical field. The working of the designed controller is studied on the real dataset of five patients undergoing surgery. The controller tracks the desired hypnosis level within the acceptable range for surgery. PMID:27293475

Control Law Design for Propofol Infusion to Regulate Depth of Hypnosis: A Nonlinear Control Strategy.

PubMed

Khaqan, Ali; Bilal, Muhammad; Ilyas, Muhammad; Ijaz, Bilal; Ali Riaz, Raja

2015-01-01

Maintaining the depth of hypnosis (DOH) during surgery is one of the major objectives of anesthesia infusion system. Continuous administration of Propofol infusion during surgical procedures is essential but increases the undue load of an anesthetist in operating room working in a multitasking setup. Manual and target controlled infusion (TCI) systems are not good at handling instabilities like blood pressure changes and heart rate variability arising due to interpatient variability. Patient safety, large interindividual variability, and less postoperative effects are the main factors to motivate automation in anesthesia. The idea of automated system for Propofol infusion excites the control engineers to come up with a more sophisticated and safe system that handles optimum delivery of drug during surgery and avoids postoperative effects. In contrast to most of the investigations with linear control strategies, the originality of this research work lies in employing a nonlinear control technique, backstepping, to track the desired hypnosis level of patients during surgery. This effort is envisioned to unleash the true capabilities of this nonlinear control technique for anesthesia systems used today in biomedical field. The working of the designed controller is studied on the real dataset of five patients undergoing surgery. The controller tracks the desired hypnosis level within the acceptable range for surgery.

Vorticity-divergence semi-Lagrangian global atmospheric model SL-AV20: dynamical core

NASA Astrophysics Data System (ADS)

Tolstykh, Mikhail; Shashkin, Vladimir; Fadeev, Rostislav; Goyman, Gordey

2017-05-01

SL-AV (semi-Lagrangian, based on the absolute vorticity equation) is a global hydrostatic atmospheric model. Its latest version, SL-AV20, provides global operational medium-range weather forecast with 20 km resolution over Russia. The lower-resolution configurations of SL-AV20 are being tested for seasonal prediction and climate modeling. The article presents the model dynamical core. Its main features are a vorticity-divergence formulation at the unstaggered grid, high-order finite-difference approximations, semi-Lagrangian semi-implicit discretization and the reduced latitude-longitude grid with variable resolution in latitude. The accuracy of SL-AV20 numerical solutions using a reduced lat-lon grid and the variable resolution in latitude is tested with two idealized test cases. Accuracy and stability of SL-AV20 in the presence of the orography forcing are tested using the mountain-induced Rossby wave test case. The results of all three tests are in good agreement with other published model solutions. It is shown that the use of the reduced grid does not significantly affect the accuracy up to the 25 % reduction in the number of grid points with respect to the regular grid. Variable resolution in latitude allows us to improve the accuracy of a solution in the region of interest.

Propellant Feed Subsystem for the X-34 Main Propulsion System

NASA Technical Reports Server (NTRS)

McDonald, J. P.; Minor, R. B.; Knight, K. C.; Champion, R. H., Jr.; Russell, F. J., Jr.

1998-01-01

The Orbital Sciences Corporation X-34 vehicle demonstrates technologies and operations key to future reusable launch vehicles. The general flight performance goal of this unmanned rocket plane is Mach 8 flight at an altitude of 250,000 feet. The Main Propulsion System supplies liquid propellants to the main engine, which provides the primary thrust for attaining mission goals. Major NMS design and operational goals are aircraft-like ground operations, quick turnaround between missions, and low initial/operational costs. This paper reviews major design and analysis aspects of the X-34 propellant feed subsystem of the X-34 Main Propulsion System. Topics include system requirements, system design, the integration of flight and feed system performance, propellant acquisition at engine start, and propellant tank terminal drain.

A new fractional operator of variable order: Application in the description of anomalous diffusion

NASA Astrophysics Data System (ADS)

Yang, Xiao-Jun; Machado, J. A. Tenreiro

2017-09-01

In this paper, a new fractional operator of variable order with the use of the monotonic increasing function is proposed in sense of Caputo type. The properties in term of the Laplace and Fourier transforms are analyzed and the results for the anomalous diffusion equations of variable order are discussed. The new formulation is efficient in modeling a class of concentrations in the complex transport process.

Advanced multivariable control of a turboexpander plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Altena, D.; Howard, M.; Bullin, K.

1998-12-31

This paper describes an application of advanced multivariable control on a natural gas plant and compares its performance to the previous conventional feed-back control. This control algorithm utilizes simple models from existing plant data and/or plant tests to hold the process at the desired operating point in the presence of disturbances and changes in operating conditions. The control software is able to accomplish this due to effective handling of process variable interaction, constraint avoidance and feed-forward of measured disturbances. The economic benefit of improved control lies in operating closer to the process constraints while avoiding significant violations. The South Texasmore » facility where this controller was implemented experienced reduced variability in process conditions which increased liquids recovery because the plant was able to operate much closer to the customer specified impurity constraint. An additional benefit of this implementation of multivariable control is the ability to set performance criteria beyond simple setpoints, including process variable constraints, relative variable merit and optimizing use of manipulated variables. The paper also details the control scheme applied to the complex turboexpander process and some of the safety features included to improve reliability.« less

Harmonic analysis of the precipitation in Greece

NASA Astrophysics Data System (ADS)

Nastos, P. T.; Zerefos, C. S.

2009-04-01

Greece is a country with a big variety of climates due to its geographical position, to the many mountain ranges and also to the multifarious and long coastline. The mountainous volumes are of such orientation that influences the distribution of the precipitation, having as a result, Western Greece to present great differentiations from Central and Eastern Greece. The application of harmonic analysis to the annual variability of precipitation is the goal of this study, so that the components, which compose the annual variability, be elicited. For this purpose, the mean monthly precipitation data from 30 meteorological stations of National Meteorological Service were used for the time period 1950-2000. The initial target is to reduce the number of variables and to detect structure in the relationships between variables. The most commonly used technique for this purpose is the application of Factor Analysis to a table having as columns the meteorological stations-variables and rows the monthly mean precipitation, so that 2 main factors were calculated, which explain the 98% of total variability of precipitation in Greece. Factor 1, representing the so-called uniform field and interpreting the most of the total variance, refers in fact to the Mediterranean depressions, affecting mainly the West of Greece and also the East Aegean and the Asia Minor coasts. In the process, the Fourier Analysis was applied to the factor scores extracted from the Factor Analysis, so that 2 harmonic components are resulted, which explain above the 98% of the total variability of each main factor, and are due to different synoptic and thermodynamic processes associated with Greece's precipitation construction. Finally, the calculation of the time of occurrence of the maximum precipitation, for each harmonic component of each one of the two main factors, gives the spatial distribution of appearance of the maximum precipitation in the Hellenic region.

System and method of modulating electrical signals using photoconductive wide bandgap semiconductors as variable resistors

DOEpatents

Harris, John Richardson; Caporaso, George J; Sampayan, Stephen E

2013-10-22

A system and method for producing modulated electrical signals. The system uses a variable resistor having a photoconductive wide bandgap semiconductor material construction whose conduction response to changes in amplitude of incident radiation is substantially linear throughout a non-saturation region to enable operation in non-avalanche mode. The system also includes a modulated radiation source, such as a modulated laser, for producing amplitude-modulated radiation with which to direct upon the variable resistor and modulate its conduction response. A voltage source and an output port, are both operably connected to the variable resistor so that an electrical signal may be produced at the output port by way of the variable resistor, either generated by activation of the variable resistor or propagating through the variable resistor. In this manner, the electrical signal is modulated by the variable resistor so as to have a waveform substantially similar to the amplitude-modulated radiation.

Dirac Operator in Several Variables and Combinatorial Identities

NASA Astrophysics Data System (ADS)

Damiano, Alberto; Souček, Vladimír

2007-09-01

The Dolbeault sequence is a fundamental tool for many problems in the function theory of several complex variables. A lot of attention was paid in the last decades to its analogue in the function theory of several Clifford variables. The first operator in this resolution is the Dirac operator in several variables. The complete description is known in dimension 4 (i.e., in the case of quaternionic variables, see [1, 6, 4]). Much less is known in higher dimensions. The case of three variables was described completely (see [18]). The full description of the complex for all dimensions is not known at present. Even the case of the stable range (i.e., when the number of variables is less or equal to the half of dimension) is still not fully understood. There are two different approaches to the stable range case, one based on classical algebraic geometry (the Hilbert syzygy theory, see [8]), the other one on representation theory (differential invariants in certain parabolic geometries, see [14, 20]). Differential operators in these resolutions are acting on vector-valued functions. Such spaces of functions are quite complicated in general and the first problem in the description of the resolution is to understand their dimensions. Both the approaches mentioned above suggest an answer to this question, although such answers look quite different. The aim of the paper is to compare these two results and to show that they lead to complicated combinatorial identities.

Dynamics and spatio-temporal variability of environmental factors in Eastern Australia using functional principal component analysis

USGS Publications Warehouse

Szabo, J.K.; Fedriani, E.M.; Segovia-Gonzalez, M. M.; Astheimer, L.B.; Hooper, M.J.

2010-01-01

This paper introduces a new technique in ecology to analyze spatial and temporal variability in environmental variables. By using simple statistics, we explore the relations between abiotic and biotic variables that influence animal distributions. However, spatial and temporal variability in rainfall, a key variable in ecological studies, can cause difficulties to any basic model including time evolution. The study was of a landscape scale (three million square kilometers in eastern Australia), mainly over the period of 19982004. We simultaneously considered qualitative spatial (soil and habitat types) and quantitative temporal (rainfall) variables in a Geographical Information System environment. In addition to some techniques commonly used in ecology, we applied a new method, Functional Principal Component Analysis, which proved to be very suitable for this case, as it explained more than 97% of the total variance of the rainfall data, providing us with substitute variables that are easier to manage and are even able to explain rainfall patterns. The main variable came from a habitat classification that showed strong correlations with rainfall values and soil types. ?? 2010 World Scientific Publishing Company.

Launch Vehicle Production and Operations Cost Metrics

NASA Technical Reports Server (NTRS)

Watson, Michael D.; Neeley, James R.; Blackburn, Ruby F.

2014-01-01

Traditionally, launch vehicle cost has been evaluated based on $/Kg to orbit. This metric is calculated based on assumptions not typically met by a specific mission. These assumptions include the specified orbit whether Low Earth Orbit (LEO), Geostationary Earth Orbit (GEO), or both. The metric also assumes the payload utilizes the full lift mass of the launch vehicle, which is rarely true even with secondary payloads.1,2,3 Other approaches for cost metrics have been evaluated including unit cost of the launch vehicle and an approach to consider the full program production and operations costs.4 Unit cost considers the variable cost of the vehicle and the definition of variable costs are discussed. The full program production and operation costs include both the variable costs and the manufacturing base. This metric also distinguishes operations costs from production costs, including pre-flight operational testing. Operations costs also consider the costs of flight operations, including control center operation and maintenance. Each of these 3 cost metrics show different sensitivities to various aspects of launch vehicle cost drivers. The comparison of these metrics provides the strengths and weaknesses of each yielding an assessment useful for cost metric selection for launch vehicle programs.

Revisiting tropical instability wave variability in the Atlantic ocean using SODA reanalysis

NASA Astrophysics Data System (ADS)

de Decco, Hatsue Takanaca; Torres Junior, Audalio Rebelo; Pezzi, Luciano Ponzi; Landau, Luiz

2018-03-01

The spatial and temporal variability of energy exchange in Tropical Instability Waves (TIWs) in the Atlantic Ocean were investigated. A spectral analysis was used to filter the 5-day mean results from Simple Ocean Data Assimilation (SODA) reanalysis spanning from 1958 to 2008. TIWs were filtered over periods of 15 to 60 days and between wavelengths of 4 and 20 longitude degrees. The main approach of this study was the use of bidirectionally filtered TIW time series as the perturbation fields, and the difference in these time series from the SODA total results was considered to be the basic state for energetics analysis. The main result was that the annual cycle (period of 360 days) was the main source of variability of the waves, and the semi-annual cycle (period of 180 days) was a secondary variation, which indicated that TIWs occurred throughout the year but with intensity that varies seasonally. In SODA, barotropic instability acts as the mechanism that feeds and extracts energy to/from TIWs at equatorial Atlantic. Baroclinic instability is the main mechanism that extracts energy from TIWs to the equatorial circulation north of the Equator. All TIW patterns of variability were observed western of 10° W. The present study reveals new evidences regarding TIW variability and suggests that future investigations should include a detailed description of TIW dynamics as part of Atlantic Ocean equatorial circulation.

Photometric search for variable stars in the young open cluster Berkeley 59

NASA Astrophysics Data System (ADS)

Lata, Sneh; Pandey, A. K.; Maheswar, G.; Mondal, Soumen; Kumar, Brijesh

2011-12-01

We present the time series photometry of stars located in the extremely young open cluster Berkeley 59. Using the 1.04-m telescope at Aryabhatta Research Institute of Observational Sciences (ARIES), Nainital, we have identified 42 variables in a field of ˜13 × 13 arcmin2 around the cluster. The probable members of the cluster have been identified using a (V, V-I) colour-magnitude diagram and a (J-H, H-K) colour-colour diagram. 31 variables have been found to be pre-main-sequence stars associated with the cluster. The ages and masses of the pre-main-sequence stars have been derived from the colour-magnitude diagram by fitting theoretical models to the observed data points. The ages of the majority of the probable pre-main-sequence variable candidates range from 1 to 5 Myr. The masses of these pre-main-sequence variable stars have been found to be in the range of ˜0.3 to ˜3.5 M⊙, and these could be T Tauri stars. The present statistics reveal that about 90 per cent T Tauri stars have period <15 d. The classical T Tauri stars are found to have a larger amplitude than the weak-line T Tauri stars. There is an indication that the amplitude decreases with an increase in mass, which could be due to the dispersal of the discs of relatively massive stars.

Quality of narrative operative reports in pancreatic surgery

PubMed Central

Wiebe, Meagan E.; Sandhu, Lakhbir; Takata, Julie L.; Kennedy, Erin D.; Baxter, Nancy N.; Gagliardi, Anna R.; Urbach, David R.; Wei, Alice C.

2013-01-01

Background Quality in health care can be evaluated using quality indicators (QIs). Elements contained in the surgical operative report are potential sources for QI data, but little is known about the completeness of the narrative operative report (NR). We evaluated the completeness of the NR for patients undergoing a pancreaticoduodenectomy. Methods We reviewed NRs for patients undergoing a pancreaticoduodenectomy over a 1-year period. We extracted 79 variables related to patient and narrator characteristics, process of care measures, surgical technique and oncology-related outcomes by document analysis. Data were coded and evaluated for completeness. Results We analyzed 74 NRs. The median number of variables reported was 43.5 (range 13–54). Variables related to surgical technique were most complete. Process of care and oncology-related variables were often omitted. Completeness of the NR was associated with longer operative duration. Conclusion The NRs were often incomplete and of poor quality. Important elements, including process of care and oncology-related data, were frequently missing. Thus, the NR is an inadequate data source for QI. Development and use of alternative reporting methods, including standardized synoptic operative reports, should be encouraged to improve documentation of care and serve as a measure of quality of surgical care. PMID:24067527

Quality of narrative operative reports in pancreatic surgery.

PubMed

Wiebe, Meagan E; Sandhu, Lakhbir; Takata, Julie L; Kennedy, Erin D; Baxter, Nancy N; Gagliardi, Anna R; Urbach, David R; Wei, Alice C

2013-10-01

Quality in health care can be evaluated using quality indicators (QIs). Elements contained in the surgical operative report are potential sources for QI data, but little is known about the completeness of the narrative operative report (NR). We evaluated the completeness of the NR for patients undergoing a pancreaticoduodenectomy. We reviewed NRs for patients undergoing a pancreaticoduodenectomy over a 1-year period. We extracted 79 variables related to patient and narrator characteristics, process of care measures, surgical technique and oncology-related outcomes by document analysis. Data were coded and evaluated for completeness. We analyzed 74 NRs. The median number of variables reported was 43.5 (range 13-54). Variables related to surgical technique were most complete. Process of care and oncology-related variables were often omitted. Completeness of the NR was associated with longer operative duration. The NRs were often incomplete and of poor quality. Important elements, including process of care and oncology-related data, were frequently missing. Thus, the NR is an inadequate data source for QI. Development and use of alternative reporting methods, including standardized synoptic operative reports, should be encouraged to improve documentation of care and serve as a measure of quality of surgical care.

Motivators and barriers to uptake of post-operative voluntary medical male circumcision follow-up in Yala division, Siaya County, Kenya

PubMed Central

Abunah, Bonface; Onkoba, Rueben; Nyagero, Josephat; Muhula, Samuel; Omondi, Edward; Guyah, Bernard; Omondi, Gregory Barnabas

2016-01-01

Introduction Follow-up visits are recommended to all voluntary medical male circumcision clients (VMMC), however, adherence is variable. High lost-to-follow-up cases limit knowledge about clinical status of clients and adverse events. This study sought to establish Motivators and Barriers to the Uptake of VMMC post-operative follow-up services in Siaya County, Kenya. Methods 277 clients from five VMMC sites in Yala were recruited immediately post-operation to participate in a telephone interview between the 21st and 31st day post-surgery during which a semi-structured questionnaire was administered. Descriptive and inferential statistics was used to analyse quantitative information using SPSS while responses from open ended questions were grouped into themes, sieved out, coded and analyzed. Results 137(49.5%) of the 277 participants utilized the follow-up services. Health education (31.4%) and emergency reviews/adverse events (24.1%) were the main motivation for returning for follow-up while occupational and other engagements (29.7%) and presumption of healing (24.6%) were the main barriers. Type of facility attended (p=0.0173), satisfaction with the discharge process (p=0.0150) and residency in Yala (p<0.001) were statistically significant to the respondents’ return for follow-up. 85(62.0%) of the participants returned on the 7th day, 9(6.6%) returned after 7 days, and 43(31.4%) returned before 7 days. Conclusion VMMC health education should include and emphasize the benefits of follow-up care to the clients and the providers should address the barriers to accessing follow-up services. Our results will inform the programme on areas identified to improve care for VMMC clients and reduce subsequent lost-to-follow-up cases. PMID:28439331

Motivators and barriers to uptake of post-operative voluntary medical male circumcision follow-up in Yala division, Siaya County, Kenya.

PubMed

Abunah, Bonface; Onkoba, Rueben; Nyagero, Josephat; Muhula, Samuel; Omondi, Edward; Guyah, Bernard; Omondi, Gregory Barnabas

2016-01-01

Follow-up visits are recommended to all voluntary medical male circumcision clients (VMMC), however, adherence is variable. High lost-to-follow-up cases limit knowledge about clinical status of clients and adverse events. This study sought to establish Motivators and Barriers to the Uptake of VMMC post-operative follow-up services in Siaya County, Kenya. 277 clients from five VMMC sites in Yala were recruited immediately post-operation to participate in a telephone interview between the 21st and 31st day post-surgery during which a semi-structured questionnaire was administered. Descriptive and inferential statistics was used to analyse quantitative information using SPSS while responses from open ended questions were grouped into themes, sieved out, coded and analyzed. 137(49.5%) of the 277 participants utilized the follow-up services. Health education (31.4%) and emergency reviews/adverse events (24.1%) were the main motivation for returning for follow-up while occupational and other engagements (29.7%) and presumption of healing (24.6%) were the main barriers. Type of facility attended (p=0.0173), satisfaction with the discharge process (p=0.0150) and residency in Yala (p<0.001) were statistically significant to the respondents' return for follow-up. 85(62.0%) of the participants returned on the 7th day, 9(6.6%) returned after 7 days, and 43(31.4%) returned before 7 days. VMMC health education should include and emphasize the benefits of follow-up care to the clients and the providers should address the barriers to accessing follow-up services. Our results will inform the programme on areas identified to improve care for VMMC clients and reduce subsequent lost-to-follow-up cases.

Learning Activity Package, Algebra 93-94, LAPs 12-22.

ERIC Educational Resources Information Center

Evans, Diane

A set of 11 teacher-prepared Learning Activity Packages (LAPs) in beginning algebra, these units cover sets, properties of operations, operations over real numbers, open expressions, solution sets of equations and inequalities, equations and inequalities with two variables, solution sets of equations with two variables, exponents, factoring and…

EFFECTS OF APPLIANCE TYPE AND OPERATING VARIABLES ON WOODSTOVE EMISSIONS: VOLUME II. APPENDICIES D-F.

EPA Science Inventory

The report gives results of a project, in support of the intergared Air Cancer Project (IACP), to provide data on the specific effects of appliance type and operating variables on woodstove emissions. samples of particulate material and volatile organic compounds (VOCs) were coll...

Three-stage variability-based reserve modifiers for enhancing flexibility reserve requirements under high variable generation penetrations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Krad, Ibrahim; Gao, David Wenzhong; Ibanez, Eduardo

2016-12-01

The electric power system has continuously evolved in order to accommodate new technologies and operating strategies. As the penetration of integrated variable generation in the system increases, it is beneficial to develop strategies that can help mitigate their effect on the grid. Historically, power system operators have held excess capacity during the commitment and dispatch process to allow the system to handle unforeseen load ramping events. As variable generation resources increase, sufficient flexibility scheduled in the system is required to ensure that system performance is not deteriorated in the presence of additional variability and uncertainty. This paper presents a systematicmore » comparison of various flexibility reserve strategies. Several of them are implemented and applied in a common test system, in order to evaluate their effect on the economic and reliable operations. Furthermore, a three stage reserve modifier algorithm is proposed and evaluated for its ability to improve system performance.« less

On-line identification of fermentation processes for ethanol production.

PubMed

Câmara, M M; Soares, R M; Feital, T; Naomi, P; Oki, S; Thevelein, J M; Amaral, M; Pinto, J C

2017-07-01

A strategy for monitoring fermentation processes, specifically, simultaneous saccharification and fermentation (SSF) of corn mash, was developed. The strategy covered the development and use of first principles, semimechanistic and unstructured process model based on major kinetic phenomena, along with mass and energy balances. The model was then used as a reference model within an identification procedure capable of running on-line. The on-line identification procedure consists on updating the reference model through the estimation of corrective parameters for certain reaction rates using the most recent process measurements. The strategy makes use of standard laboratory measurements for sugars quantification and in situ temperature and liquid level data. The model, along with the on-line identification procedure, has been tested against real industrial data and have been able to accurately predict the main variables of operational interest, i.e., state variables and its dynamics, and key process indicators. The results demonstrate that the strategy is capable of monitoring, in real time, this complex industrial biomass fermentation. This new tool provides a great support for decision-making and opens a new range of opportunities for industrial optimization.

Computational Study of the Impact of Unsteadiness on the Aerodynamic Performance of a Variable- Speed Power Turbine

NASA Technical Reports Server (NTRS)

Welch, Gerard E.

2012-01-01

The design-point and off-design performance of an embedded 1.5-stage portion of a variable-speed power turbine (VSPT) was assessed using Reynolds-Averaged Navier-Stokes (RANS) analyses with mixing-planes and sector-periodic, unsteady RANS analyses. The VSPT provides one means by which to effect the nearly 50 percent main-rotor speed change required for the NASA Large Civil Tilt-Rotor (LCTR) application. The change in VSPT shaft-speed during the LCTR mission results in blade-row incidence angle changes of as high as 55 . Negative incidence levels of this magnitude at takeoff operation give rise to a vortical flow structure in the pressure-side cove of a high-turn rotor that transports low-momentum flow toward the casing endwall. The intent of the effort was to assess the impact of unsteadiness of blade-row interaction on the time-mean flow and, specifically, to identify potential departure from the predicted trend of efficiency with shaft-speed change of meanline and 3-D RANS/mixing-plane analyses used for design.

Drivers of long-term precipitation and runoff variability in the southeastern USA

NASA Astrophysics Data System (ADS)

Engström, Johanna; Waylen, Peter

2018-02-01

The hydroclimatology of the southeastern USA (AL, GA, NC, SC, and TN) is analyzed from a holistic perspective, including multiple climate drivers. Monthly precipitation modeled by the PRISM group and runoff data (1952-2011) from 18 basins are analyzed using a single-field based principal component's analysis. Results indicate that the Atlantic Multidecadal Oscillation and El Niño-Southern Oscillation are the main atmospheric drivers of hydroclimate variability in the region, sometimes operating at several months' lag. Their influence is the strongest in the fall through spring, which corresponds with the dry season in the southern parts of the study area thereby increasing pressure on already limited water resources. The Arctic Oscillation, North Atlantic Oscillation, and Pacific-North American patterns vary on shorter-term bases, and also show a significant, but temporally more sporadic influence. Insight is also brought to the ongoing discussion, confirming the disassociation of the Arctic and North Atlantic Oscillation. Findings can be used in water resources forecasting, giving an indication of expected water volumes several months ahead.

Mobile measurements of air pollutants with an instrumented car in populated areas

NASA Astrophysics Data System (ADS)

Weber, Konradin; Scharifi, Emad; Fischer, Christian; Pohl, Tobias; Lange, Martin; Boehlke, Christoph

2017-04-01

Detailed mobile measurement of gases and fine particulate matter has been reported in the literature to be suitable to exhibit the air pollutants concentration in populated areas. This concentration is linked to the increase of number of cars, construction areas, industries and other emission sources. However, fixed measurement stations, mostly operated by environmental agencies, are limited in numbers and cannot cover a large area in monitoring. For this reason, to overcome this drawback, mobile measurements of the variability of gases (such as O3, NO, NO2) and particulate matter concentration were carried out during this study using an instrumented car. This car was able to deliver measurement results of all these compounds in a large area. The experimental results in this work demonstrate a large spatial variability of gases and fine particulate matters mainly depended on the traffic density and the location. These effects are especially obvious in the city core and the high traffic roads. In terms of fine particulate matter, this becomes evident for PM 10 and PM 2.5, where the mass and number concentration increases with arriving these zones.

Atmospheric form drag over Arctic sea ice derived from high-resolution IceBridge elevation data

NASA Astrophysics Data System (ADS)

Petty, A.; Tsamados, M.; Kurtz, N. T.

2016-02-01

Here we present a detailed analysis of atmospheric form drag over Arctic sea ice, using high resolution, three-dimensional surface elevation data from the NASA Operation IceBridge Airborne Topographic Mapper (ATM) laser altimeter. Surface features in the sea ice cover are detected using a novel feature-picking algorithm. We derive information regarding the height, spacing and orientation of unique surface features from 2009-2014 across both first-year and multiyear ice regimes. The topography results are used to explicitly calculate atmospheric form drag coefficients; utilizing existing form drag parameterizations. The atmospheric form drag coefficients show strong regional variability, mainly due to variability in ice type/age. The transition from a perennial to a seasonal ice cover therefore suggest a decrease in the atmospheric form drag coefficients over Arctic sea ice in recent decades. These results are also being used to calibrate a recent form drag parameterization scheme included in the sea ice model CICE, to improve the representation of form drag over Arctic sea ice in global climate models.

Balancing Area Coordination: Efficiently Integrating Renewable Energy Into the Grid, Greening the Grid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katz, Jessica; Denholm, Paul; Cochran, Jaquelin

2015-06-01

Greening the Grid provides technical assistance to energy system planners, regulators, and grid operators to overcome challenges associated with integrating variable renewable energy into the grid. Coordinating balancing area operation can promote more cost and resource efficient integration of variable renewable energy, such as wind and solar, into power systems. This efficiency is achieved by sharing or coordinating balancing resources and operating reserves across larger geographic boundaries.

The finite element method scheme for a solution of an evolution variational inequality with a nonlocal space operator

NASA Astrophysics Data System (ADS)

Glazyrina, O. V.; Pavlova, M. F.

2016-11-01

We consider the parabolic inequality with monotone with respect to a gradient space operator, which is depended on integral with respect to space variables solution characteristic. We construct a two-layer differential scheme for this problem with use of penalty method, semidiscretization with respect to time variable method and the finite element method (FEM) with respect to space variables. We proved a convergence of constructed mothod.

Integrating Solar Power onto the Electric Grid - Bridging the Gap between Atmospheric Science, Engineering and Economics

NASA Astrophysics Data System (ADS)

Ghonima, M. S.; Yang, H.; Zhong, X.; Ozge, B.; Sahu, D. K.; Kim, C. K.; Babacan, O.; Hanna, R.; Kurtz, B.; Mejia, F. A.; Nguyen, A.; Urquhart, B.; Chow, C. W.; Mathiesen, P.; Bosch, J.; Wang, G.

2015-12-01

One of the main obstacles to high penetrations of solar power is the variable nature of solar power generation. To mitigate variability, grid operators have to schedule additional reliability resources, at considerable expense, to ensure that load requirements are met by generation. Thus despite the cost of solar PV decreasing, the cost of integrating solar power will increase as penetration of solar resources onto the electric grid increases. There are three principal tools currently available to mitigate variability impacts: (i) flexible generation, (ii) storage, either virtual (demand response) or physical devices and (iii) solar forecasting. Storage devices are a powerful tool capable of ensuring smooth power output from renewable resources. However, the high cost of storage is prohibitive and markets are still being designed to leverage their full potential and mitigate their limitation (e.g. empty storage). Solar forecasting provides valuable information on the daily net load profile and upcoming ramps (increasing or decreasing solar power output) thereby providing the grid advance warning to schedule ancillary generation more accurately, or curtail solar power output. In order to develop solar forecasting as a tool that can be utilized by the grid operators we identified two focus areas: (i) develop solar forecast technology and improve solar forecast accuracy and (ii) develop forecasts that can be incorporated within existing grid planning and operation infrastructure. The first issue required atmospheric science and engineering research, while the second required detailed knowledge of energy markets, and power engineering. Motivated by this background we will emphasize area (i) in this talk and provide an overview of recent advancements in solar forecasting especially in two areas: (a) Numerical modeling tools for coastal stratocumulus to improve scheduling in the day-ahead California energy market. (b) Development of a sky imager to provide short term forecasts (0-20 min ahead) to improve optimization and control of equipment on distribution feeders with high penetration of solar. Leveraging such tools that have seen extensive use in the atmospheric sciences supports the development of accurate physics-based solar forecast models. Directions for future research are also provided.

Physician communication in the operating room: expanding application of face-negotiation theory to the health communication context.

PubMed

Kirschbaum, Kristin

2012-01-01

Communication variables that are associated with face-negotiation theory were examined in a sample of operating-room physicians. A survey was administered to anesthesiologists and surgeons at a teaching hospital in the southwestern United States to measure three variables commonly associated with face-negotiation theory: conflict-management style, face concern, and self-construal. The survey instrument that was administered to physicians includes items that measured these three variables in previous face-negotiation research with slight modification of item wording for relevance in the medical setting. The physician data were analyzed using confirmatory factor analysis, Pearson's correlations, and t-tests. Results of this initial investigation showed that variables associated with face-negotiation theory were evident in the sample physician population. In addition, the correlations were similar among variables in the medical sample as those found in previous face-negotiation research. Finally, t-tests suggest variance between anesthesiologists and surgeons on specific communication variables. These findings suggest three implications that warrant further investigation with expanded sample size: (1) An intercultural communication theory and instrument can be utilized for health communication research; (2) as applied in a medical context, face-negotiation theory can be expanded beyond traditional intercultural communication boundaries; and (3) theoretically based communication structures applied in a medical context could help explain physician miscommunication in the operating room to assist future design of communication training programs for operating-room physicians.

Breeding objectives for pigs in Kenya. I: bio-economic model development and application to smallholder production systems.

PubMed

Mbuthia, Jackson M; Rewe, Thomas O; Kahi, Alexander K

2015-02-01

A deterministic bio-economic model was developed and applied to evaluate biological and economic variables that characterize smallholder pig production systems in Kenya. Two pig production systems were considered namely, semi-intensive (SI) and extensive (EX). The input variables were categorized into biological variables including production and functional traits, nutritional variables, management variables and economic variables. The model factored the various sow physiological systems including gestation, farrowing, lactation, growth and development. The model was developed to evaluate a farrow to finish operation, but the results were customized to account for a farrow to weaner operation for a comparative analysis. The operations were defined as semi-intensive farrow to finish (SIFF), semi-intensive farrow to weaner (SIFW), extensive farrow to finish (EXFF) and extensive farrow to weaner (EXFW). In SI, the profits were the highest at KES. 74,268.20 per sow per year for SIFF against KES. 4026.12 for SIFW. The corresponding profits for EX were KES. 925.25 and KES. 626.73. Feed costs contributed the major part of the total costs accounting for 67.0, 50.7, 60.5 and 44.5 % in the SIFF, SIFW, EXFF and EXFW operations, respectively. The bio-economic model developed could be extended with modifications for use in deriving economic values for breeding goal traits for pigs under smallholder production systems in other parts of the tropics.

Determination of main fruits in adulterated nectars by ATR-FTIR spectroscopy combined with multivariate calibration and variable selection methods.

PubMed

Miaw, Carolina Sheng Whei; Assis, Camila; Silva, Alessandro Rangel Carolino Sales; Cunha, Maria Luísa; Sena, Marcelo Martins; de Souza, Scheilla Vitorino Carvalho

2018-07-15

Grape, orange, peach and passion fruit nectars were formulated and adulterated by dilution with syrup, apple and cashew juices at 10 levels for each adulterant. Attenuated total reflectance Fourier transform mid infrared (ATR-FTIR) spectra were obtained. Partial least squares (PLS) multivariate calibration models allied to different variable selection methods, such as interval partial least squares (iPLS), ordered predictors selection (OPS) and genetic algorithm (GA), were used to quantify the main fruits. PLS improved by iPLS-OPS variable selection showed the highest predictive capacity to quantify the main fruit contents. The selected variables in the final models varied from 72 to 100; the root mean square errors of prediction were estimated from 0.5 to 2.6%; the correlation coefficients of prediction ranged from 0.948 to 0.990; and, the mean relative errors of prediction varied from 3.0 to 6.7%. All of the developed models were validated. Copyright © 2018 Elsevier Ltd. All rights reserved.

Framework for a U.S. Geological Survey Hydrologic Climate-Response Program in Maine

USGS Publications Warehouse

Hodgkins, Glenn A.; Lent, Robert M.; Dudley, Robert W.; Schalk, Charles W.

2009-01-01

This report presents a framework for a U.S. Geological Survey (USGS) hydrologic climate-response program designed to provide early warning of changes in the seasonal water cycle of Maine. Climate-related hydrologic changes on Maine's rivers and lakes in the winter and spring during the last century are well documented, and several river and lake variables have been shown to be sensitive to air-temperature changes. Monitoring of relevant hydrologic data would provide important baseline information against which future climate change can be measured. The framework of the hydrologic climate-response program presented here consists of four major parts: (1) identifying homogeneous climate-response regions; (2) identifying hydrologic components and key variables of those components that would be included in a hydrologic climate-response data network - as an example, streamflow has been identified as a primary component, with a key variable of streamflow being winter-spring streamflow timing; the data network would be created by maintaining existing USGS data-collection stations and establishing new ones to fill data gaps; (3) regularly updating historical trends of hydrologic data network variables; and (4) establishing basins for process-based studies. Components proposed for inclusion in the hydrologic climate-response data network have at least one key variable for which substantial historical data are available. The proposed components are streamflow, lake ice, river ice, snowpack, and groundwater. The proposed key variables of each component have extensive historical data at multiple sites and are expected to be responsive to climate change in the next few decades. These variables are also important for human water use and (or) ecosystem function. Maine would be divided into seven climate-response regions that follow major river-basin boundaries (basins subdivided to hydrologic units with 8-digit codes or larger) and have relatively homogeneous climates. Key hydrologic variables within each climate-response region would be analyzed regularly to maintain up-to-date analyses of year-to-year variability, decadal variability, and longer term trends. Finally, one basin in each climate-response region would be identified for process-based hydrologic and ecological studies.

Bayesian spatio-temporal discard model in a demersal trawl fishery

NASA Astrophysics Data System (ADS)

Grazia Pennino, M.; Muñoz, Facundo; Conesa, David; López-Quílez, Antonio; Bellido, José M.

2014-07-01

Spatial management of discards has recently been proposed as a useful tool for the protection of juveniles, by reducing discard rates and can be used as a buffer against management errors and recruitment failure. In this study Bayesian hierarchical spatial models have been used to analyze about 440 trawl fishing operations of two different metiers, sampled between 2009 and 2012, in order to improve our understanding of factors that influence the quantity of discards and to identify their spatio-temporal distribution in the study area. Our analysis showed that the relative importance of each variable was different for each metier, with a few similarities. In particular, the random vessel effect and seasonal variability were identified as main driving variables for both metiers. Predictive maps of the abundance of discards and maps of the posterior mean of the spatial component show several hot spots with high discard concentration for each metier. We argue how the seasonal/spatial effects, and the knowledge about the factors influential to discarding, could potentially be exploited as potential mitigation measures for future fisheries management strategies. However, misidentification of hotspots and uncertain predictions can culminate in inappropriate mitigation practices which can sometimes be irreversible. The proposed Bayesian spatial method overcomes these issues, since it offers a unified approach which allows the incorporation of spatial random-effect terms, spatial correlation of the variables and the uncertainty of the parameters in the modeling process, resulting in a better quantification of the uncertainty and accurate predictions.

Joint control of terrestrial gross primary productivity by plant phenology and physiology

PubMed Central

Xia, Jianyang; Niu, Shuli; Ciais, Philippe; Janssens, Ivan A.; Chen, Jiquan; Ammann, Christof; Arain, Altaf; Blanken, Peter D.; Cescatti, Alessandro; Bonal, Damien; Buchmann, Nina; Curtis, Peter S.; Chen, Shiping; Dong, Jinwei; Flanagan, Lawrence B.; Frankenberg, Christian; Georgiadis, Teodoro; Gough, Christopher M.; Hui, Dafeng; Kiely, Gerard; Li, Jianwei; Lund, Magnus; Magliulo, Vincenzo; Marcolla, Barbara; Merbold, Lutz; Olesen, Jørgen E.; Piao, Shilong; Raschi, Antonio; Roupsard, Olivier; Suyker, Andrew E.; Vaccari, Francesco P.; Varlagin, Andrej; Vesala, Timo; Wilkinson, Matthew; Weng, Ensheng; Yan, Liming; Luo, Yiqi

2015-01-01

Terrestrial gross primary productivity (GPP) varies greatly over time and space. A better understanding of this variability is necessary for more accurate predictions of the future climate–carbon cycle feedback. Recent studies have suggested that variability in GPP is driven by a broad range of biotic and abiotic factors operating mainly through changes in vegetation phenology and physiological processes. However, it is still unclear how plant phenology and physiology can be integrated to explain the spatiotemporal variability of terrestrial GPP. Based on analyses of eddy–covariance and satellite-derived data, we decomposed annual terrestrial GPP into the length of the CO2 uptake period (CUP) and the seasonal maximal capacity of CO2 uptake (GPPmax). The product of CUP and GPPmax explained >90% of the temporal GPP variability in most areas of North America during 2000–2010 and the spatial GPP variation among globally distributed eddy flux tower sites. It also explained GPP response to the European heatwave in 2003 (r2 = 0.90) and GPP recovery after a fire disturbance in South Dakota (r2 = 0.88). Additional analysis of the eddy–covariance flux data shows that the interbiome variation in annual GPP is better explained by that in GPPmax than CUP. These findings indicate that terrestrial GPP is jointly controlled by ecosystem-level plant phenology and photosynthetic capacity, and greater understanding of GPPmax and CUP responses to environmental and biological variations will, thus, improve predictions of GPP over time and space. PMID:25730847

wayGoo recommender system: personalized recommendations for events scheduling, based on static and real-time information

NASA Astrophysics Data System (ADS)

Thanos, Konstantinos-Georgios; Thomopoulos, Stelios C. A.

2016-05-01

wayGoo is a fully functional application whose main functionalities include content geolocation, event scheduling, and indoor navigation. However, significant information about events do not reach users' attention, either because of the size of this information or because some information comes from real - time data sources. The purpose of this work is to facilitate event management operations by prioritizing the presented events, based on users' interests using both, static and real - time data. Through the wayGoo interface, users select conceptual topics that are interesting for them. These topics constitute a browsing behavior vector which is used for learning users' interests implicitly, without being intrusive. Then, the system estimates user preferences and return an events list sorted from the most preferred one to the least. User preferences are modeled via a Naïve Bayesian Network which consists of: a) the `decision' random variable corresponding to users' decision on attending an event, b) the `distance' random variable, modeled by a linear regression that estimates the probability that the distance between a user and each event destination is not discouraging, ` the seat availability' random variable, modeled by a linear regression, which estimates the probability that the seat availability is encouraging d) and the `relevance' random variable, modeled by a clustering - based collaborative filtering, which determines the relevance of each event users' interests. Finally, experimental results show that the proposed system contribute essentially to assisting users in browsing and selecting events to attend.

Interpreting operational altimetry signals in near-coastal areas using underwater autonomous vehicles and remotely sensed ocean colour data

NASA Astrophysics Data System (ADS)

Borrione, Ines; Oddo, Paolo; Russo, Aniello; Coelho, Emanuel

2017-04-01

During the LOGMEC16 (Long-Term Glider Mission for Environmental Characterization) sea trial carried out in the eastern Ligurian Sea (Northwestern Mediterranean Sea), two oceanographic gliders rated to a maximum depth of 1000m were operating continuously from 3 May to 27 June 2016. When possible, glider tracks were synchronized with the footprints of contemporaneous altimeters (i.e., Jason 2, Altika and Cryosat 2). Temperature and salinity measured by the gliders along the tracks that were co-localized with the altimeter passages, were used to calculate along-track dynamic heights. The latter were then compared with near-real time absolute sea level CMEMS-TAPAS (Copernicus Marine Environment Monitoring Service - Tailored Product for Data Assimilation) product. TAPAS provides along-track sea level anomaly (SLA) estimates together with all the terms used in the correction and the associated Mean Dynamic Topography. Where available, the CMEMS near-real time 1km resolution, Aqua-MODIS ocean colour data was also used as a tracer of the main oceanographic features of the region. Comparison between SLA derived from gliders and TAPAS along common transects, indicates that differences increase for larger sampling time lags between platforms and especially when time differences exceed 20 hrs. In fact, contemporaneous ocean color images reveal the presence of several mesoscale/sub-mesoscale structures (i.e., transient meanders and filaments), suggesting that the oceanographic variability of the region is likely the main cause for the differences observed between the glider and altimetry-based SLA. Results from this study provide additional evidence of the advantages on using a networked ocean observing system. In fact, the interpretation of in-situ observations obtained from a continuously operating sampling platform (also during ongoing experiments at sea) can be greatly improved when combined with other operational datasets, as the CMEMS SLA used here.

Twin-spool turbopumps for ''low'' net positive suction pressure operations

NASA Technical Reports Server (NTRS)

Bair, E. K.; Campbell, W. E.; Ford, O. I.

1970-01-01

Modified single-shaft turbopump incorporates inducer and main pump, each separately driven at different speeds through coaxial-shaft arrangement. Inducer operates at low speed for low net positive suction pressure, main pump operates at high speed to generate high pressure. This arrangement requires no external control for the inducer.

Preparation of Effective Operating Manuals to Support Waste Management Plant Operator Training

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, S. R.

2003-02-25

Effective plant operating manuals used in a formal training program can make the difference between a successful operation and a failure. Once the plant process design and control strategies have been fixed, equipment has been ordered, and the plant is constructed, the only major variable affecting success is the capability of plant operating personnel. It is essential that the myriad details concerning plant operation are documented in comprehensive operating manuals suitable for training the non-technical personnel that will operate the plant. These manuals must cover the fundamental principles of each unit operation including how each operates, what process variables aremore » important, and the impact of each variable on the overall process. In addition, operators must know the process control strategies, process interlocks, how to respond to alarms, each of the detailed procedures required to start up and optimize the plant, and every control loop-including when it is appropriate to take manual control. More than anything else, operating mistakes during the start-up phase can lead to substantial delays in achieving design processing rates as well as to problems with government authorities if environmental permit limits are exceeded. The only way to assure return on plant investment is to ensure plant operators have the knowledge to properly run the plant from the outset. A comprehensive set of operating manuals specifically targeted toward plant operators and supervisors written by experienced operating personnel is the only effective way to provide the necessary information for formal start-up training.« less

An Attempt To Estimate The Contribution Of Variability Of Wetland Extent On The Variability Of The Atmospheric Methane Growth Rate In The Years 1993-2000.

NASA Astrophysics Data System (ADS)

Ringeval, B.; de Noblet-Ducoudre, N.; Prigent, C.; Bousquet, P.

2006-12-01

The atmospheric methane growth rate presents lots of seasonal and year-to-year variations. Large uncertainties still exist in the relative part of differents sources and sinks on these variations. We have considered, in this study, the main natural sources of methane and the supposed main variable source, i.e. wetlands, and tried to simulate the variations of their emissions considering the variability of the wetland extent and of the climate. For this study, we use the methane emission model of Walter et al. (2001) and the quantification of the flooded areas for the years 1993-2000 obtained with a suite of satellite observations by Prigent et al. (2001). The data necessary to the Walter's model are obtained with simulation of a dynamic global vegetation model ORCHIDEE (Krinner et al. (2005)) constrained by the NCC climate data (Ngo-Duc et al. (2005)) and after imposing a water-saturated soil to approach productivity of wetlands. We calculate global annual methane emissions from wetlands to be 400 Tg per year, that is higher than previous results obtained with fixed wetland extent. Simulations are realised to estimate the part of variability in the emissions explained by the variability of the wetland extent. It seems that the year-to-year emission variability is mainly explained by the interannual variability of wetland extent. The seasonnal variability is explained for 75% in the tropics and only for 40% in the north of 30°N by variability of wetlands extend. Finally, we compare results with a top-down approach of Bousquet et al.(2006).

Deployment stressors and physical health among OEF/OIF veterans: the role of PTSD.

PubMed

Nillni, Yael I; Gradus, Jaimie L; Gutner, Cassidy A; Luciano, Matthew T; Shipherd, Jillian C; Street, Amy E

2014-11-01

There is a large body of literature documenting the relationship between traumatic stress and deleterious physical health outcomes. Although posttraumatic stress disorder (PTSD) symptoms have been proposed to explain this relationship, previous research has produced inconsistent results when moderating variables such as gender or type of traumatic stressor are considered. Within a large sample of Operation Enduring Freedom and Operation Iraqi Freedom (OEF/OIF) Veterans, the current study examined if deployment stressors (i.e., combat stress, harassment stress) contributed unique variance to the prediction of physical health symptoms (i.e., pain, nonpain) beyond the effects of PTSD symptoms. A total of 2,332 OEF/OIF Veterans, with equal representation of women and men, completed a series of self-report measures assessing deployment stressors, PTSD symptoms, and physical health symptoms. RESULTS revealed that harassment, but not combat stress, added unique variance in the prediction of pain and nonpain symptoms after accounting for PTSD symptoms. This study extends the existing literature by demonstrating the unique influence of harassment stress on physical health outcomes. Specifically, the relationship between combat stress and physical health symptoms appears to be explained mainly by an individual's experience of PTSD symptoms, whereas the relationship between harassment stress and physical health symptoms is not fully explained by PTSD symptoms, suggesting that other variables may be involved in the pathway from harassment stress to physical health symptoms. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Grassmann phase space methods for fermions. II. Field theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dalton, B.J., E-mail: bdalton@swin.edu.au; Jeffers, J.; Barnett, S.M.

In both quantum optics and cold atom physics, the behaviour of bosonic photons and atoms is often treated using phase space methods, where mode annihilation and creation operators are represented by c-number phase space variables, with the density operator equivalent to a distribution function of these variables. The anti-commutation rules for fermion annihilation, creation operators suggests the possibility of using anti-commuting Grassmann variables to represent these operators. However, in spite of the seminal work by Cahill and Glauber and a few applications, the use of Grassmann phase space methods in quantum-atom optics to treat fermionic systems is rather rare, thoughmore » fermion coherent states using Grassmann variables are widely used in particle physics. This paper presents a phase space theory for fermion systems based on distribution functionals, which replace the density operator and involve Grassmann fields representing anti-commuting fermion field annihilation, creation operators. It is an extension of a previous phase space theory paper for fermions (Paper I) based on separate modes, in which the density operator is replaced by a distribution function depending on Grassmann phase space variables which represent the mode annihilation and creation operators. This further development of the theory is important for the situation when large numbers of fermions are involved, resulting in too many modes to treat separately. Here Grassmann fields, distribution functionals, functional Fokker–Planck equations and Ito stochastic field equations are involved. Typical applications to a trapped Fermi gas of interacting spin 1/2 fermionic atoms and to multi-component Fermi gases with non-zero range interactions are presented, showing that the Ito stochastic field equations are local in these cases. For the spin 1/2 case we also show how simple solutions can be obtained both for the untrapped case and for an optical lattice trapping potential.« less

Nearest-neighbor guided evaluation of data reliability and its applications.

PubMed

Boongoen, Tossapon; Shen, Qiang

2010-12-01

The intuition of data reliability has recently been incorporated into the main stream of research on ordered weighted averaging (OWA) operators. Instead of relying on human-guided variables, the aggregation behavior is determined in accordance with the underlying characteristics of the data being aggregated. Data-oriented operators such as the dependent OWA (DOWA) utilize centralized data structures to generate reliable weights, however. Despite their simplicity, the approach taken by these operators neglects entirely any local data structure that represents a strong agreement or consensus. To address this issue, the cluster-based OWA (Clus-DOWA) operator has been proposed. It employs a cluster-based reliability measure that is effective to differentiate the accountability of different input arguments. Yet, its actual application is constrained by the high computational requirement. This paper presents a more efficient nearest-neighbor-based reliability assessment for which an expensive clustering process is not required. The proposed measure can be perceived as a stress function, from which the OWA weights and associated decision-support explanations can be generated. To illustrate the potential of this measure, it is applied to both the problem of information aggregation for alias detection and the problem of unsupervised feature selection (in which unreliable features are excluded from an actual learning process). Experimental results demonstrate that these techniques usually outperform their conventional state-of-the-art counterparts.

Anaerobic treatment of Tequila vinasses in a CSTR-type digester.

PubMed

Méndez-Acosta, Hugo Oscar; Snell-Castro, Raúl; Alcaraz-González, Víctor; González-Alvarez, Víctor; Pelayo-Ortiz, Carlos

2010-06-01

Tequila industries in general produce great volumes of effluents with high pollutant loads, which are discharged (untreated or partially treated) into natural receivers, thus causing severe environmental problems. In this contribution, we propose an integrated system as a first step to comply with the Mexican ecological norms and stabilize the anaerobic treatment of Tequila vinasses with main design criteria: simple and easy operation, reduce operating time and associated costs (maintenance), integrated and compact design, minimal cost of set-up, start-up, monitoring and control. This system is composed of a fully instrumented and automated lab-scale CSTR-type digester, on-line measuring devices of key variables (pH, temperature, flow rates, etc.), which are used along with off-line readings of chemical oxygen demand (COD), biogas composition, alkalinity and volatile fatty acids to guarantee the operational stability of the anaerobic digestion process. The system performance was evaluated for 200 days and the experimental results show that even under the influence of load disturbances, it is possible to reduce the COD concentration to 85% in the start-up phase and up to 95% during the normal operation phase while producing a biogas with a methane composition greater than 65%. It is also shown that in order to maintain an efficient treatment, the buffering capacity (given by the alkalinity ratio, alpha = intermediate alkalinity/total alkalinity) must be closely monitored.

Analysis 320 coal mine accidents using structural equation modeling with unsafe conditions of the rules and regulations as exogenous variables.

PubMed

Zhang, Yingyu; Shao, Wei; Zhang, Mengjia; Li, Hejun; Yin, Shijiu; Xu, Yingjun

2016-07-01

Mining has been historically considered as a naturally high-risk industry worldwide. Deaths caused by coal mine accidents are more than the sum of all other accidents in China. Statistics of 320 coal mine accidents in Shandong province show that all accidents contain indicators of "unsafe conditions of the rules and regulations" with a frequency of 1590, accounting for 74.3% of the total frequency of 2140. "Unsafe behaviors of the operator" is another important contributory factor, which mainly includes "operator error" and "venturing into dangerous places." A systems analysis approach was applied by using structural equation modeling (SEM) to examine the interactions between the contributory factors of coal mine accidents. The analysis of results leads to three conclusions. (i) "Unsafe conditions of the rules and regulations," affect the "unsafe behaviors of the operator," "unsafe conditions of the equipment," and "unsafe conditions of the environment." (ii) The three influencing factors of coal mine accidents (with the frequency of effect relation in descending order) are "lack of safety education and training," "rules and regulations of safety production responsibility," and "rules and regulations of supervision and inspection." (iii) The three influenced factors (with the frequency in descending order) of coal mine accidents are "venturing into dangerous places," "poor workplace environment," and "operator error." Copyright © 2016 Elsevier Ltd. All rights reserved.

Proposal of a Budget-Friendly Camera Holder for Endoscopic Ear Surgery.

PubMed

Ozturan, Orhan; Yenigun, Alper; Aksoy, Fadlullah; Ertas, Burak

2018-01-01

Endoscopic ear surgery (EES) is increasingly a preferred technique in otologic society. It offers excellent visualization of the anatomical structures directly and behind the corners with variable angled telescopes. It also provides reduced operative morbidity due to being able to perform surgical interventions with less invasive approaches. Operative preparation and setup time and cost of endoscopy system are less expensive compared with surgical microscopes. On the other hand, the main disadvantage of EES is that the surgery has to be performed with 1 single hand. It is certainly restrictive for an ear surgeon who has been operating with 2 hands under otologic microscopic views for years and certainly requires a learning period and perseverance. Holding the endoscope by a second surgeon is not executable because of insufficient surgical space.Endoscope/camera holders have been developed for those who need the comfort and convenience afforded by double-handed microscopic ear surgery. An ideal endoscope holder should be easy-to-set up, easily controlled, providing a variety of angled views, allowing the surgeon to operate with 2 hands and, budget-friendly. In this article, a commercially available 11-inch magic arm camera holder is proposed by the authors to be used in EES due to its versatile, convenient, and budget-friendly features. It allows 2-handed EES through existing technology and is affordable for surgeons looking for a low-cost and practical solution.

Wave Intensity Analysis of Right Ventricular Function during Pulsed Operation of Rotary Left Ventricular Assist Devices.

PubMed

Bouwmeester, J Christopher; Park, Jiheum; Valdovinos, John; Bonde, Pramod

2018-05-29

Changing the speed of left ventricular assist devices (LVADs) cyclically may be useful to restore aortic pulsatility; however, the effects of this pulsation on right ventricular (RV) function are unknown. This study investigates the effects of direct ventricular interaction by quantifying the amount of wave energy created by RV contraction when axial and centrifugal LVADs are used to assist the left ventricle. In 4 anesthetized pigs, pressure and flow were measured in the main pulmonary artery and wave intensity analysis was used to identify and quantify the energy of waves created by the RV. The axial pump depressed the intensity of waves created by RV contraction compared with the centrifugal pump. In both pump designs, there were only minor and variable differences between the continuous and pulsed operation on RV function. The axial pump causes the RV to contract with less energy compared with a centrifugal design. Diminishing the ability of the RV to produce less energy translates to less pressure and flow produced, which may lead to LVAD-induced RV failure. The effects of pulsed LVAD operation on the RV appear to be minimal during acute observation of healthy hearts. Further study is necessary to uncover the effects of other modes of speed modulation with healthy and unhealthy hearts to determine if pulsed operation will benefit patients by reducing LVAD complications.

Neutron Source Facility Training Simulator Based on EPICS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Young Soo; Wei, Thomas Y.; Vilim, Richard B.

A plant operator training simulator is developed for training the plant operators as well as for design verification of plant control system (PCS) and plant protection system (PPS) for the Kharkov Institute of Physics and Technology Neutron Source Facility. The simulator provides the operator interface for the whole plant including the sub-critical assembly coolant loop, target coolant loop, secondary coolant loop, and other facility systems. The operator interface is implemented based on Experimental Physics and Industrial Control System (EPICS), which is a comprehensive software development platform for distributed control systems. Since its development at Argonne National Laboratory, it has beenmore » widely adopted in the experimental physics community, e.g. for control of accelerator facilities. This work is the first implementation for a nuclear facility. The main parts of the operator interface are the plant control panel and plant protection panel. The development involved implementation of process variable database, sequence logic, and graphical user interface (GUI) for the PCS and PPS utilizing EPICS and related software tools, e.g. sequencer for sequence logic, and control system studio (CSS-BOY) for graphical use interface. For functional verification of the PCS and PPS, a plant model is interfaced, which is a physics-based model of the facility coolant loops implemented as a numerical computer code. The training simulator is tested and demonstrated its effectiveness in various plant operation sequences, e.g. start-up, shut-down, maintenance, and refueling. It was also tested for verification of the plant protection system under various trip conditions.« less

Temporal and spatial variations of polycyclic aromatic hydrocarbon concentrations around a coke oven plant.

PubMed

Stella, Anna; Piccardo, Maria Teresa; Pala, Mauro; Balducci, Daniele; Cipolla, Massimo; Ceppi, Marcello; Valerio, Federico

2012-09-01

From 1995 to 2004, in Genoa, Italy, daily concentrations of twelve polycyclic aromatic hydrocarbons (PAHs) were measured in particulate phase (PM10), around a coke oven plant in operation from the 1950s and closed in 2002. The study permitted to identify the coke oven as the main PAH source in Genoa, causing constant exceeding of benzo(a)pyrene (BaP) air quality target (1.0 ng/m3) in the urban area till 1,900 meters distance downwind the plant. For this reason the plant was closed. Distance and daily hours downwind the coke plant were the main sources of variability of toxic BaP equivalent (BaPeq) concentrations and equations that best fitted these variables were experimentally obtained. During full plant activity, annual average BaPeq concentrations, measured in the three sampling sites aligned downwind to the summer prevalent winds, were: 85 ng/m3 at 40 m (site 2, industrial area), 13.2 ng/m3 at 300 m (site 3, residential area) and 5.6 ng/m3 at 575 m (site 4, residential area). Soon after the coke oven's closure (February 2002) BaPeq concentrations (annual average) measured in residential area, decreased drastically: 0.2 ng/m3 at site 3, 0.4 ng/m3 at site 4. Comparing 1998 and 2003 data, BaPeq concentrations decreased 97.6% in site 3 and 92.8% in site 4. Samples collected at site 3, during the longest downwind conditions, provided a reliable PAH profile of fugitive coke oven emissions. This profile was significantly different from the PAH profile, contemporary found at site 5, near the traffic flow. This study demonstrates that risk assessment based only on distance of residences from a coke plant can be heavily inaccurate and confirmed that seasonal variability of BaPeq concentrations and high variability of fugitive emissions of PAHs during coke oven activities require at least one year of frequent and constant monitoring (10-15 samples each month). Around a coking plant, polycyclic aromatic hydrocarbons (PAHs), concentrations depend mainly on downwind hours and distance. Equations that best fit these variables were experimentally calculated. Fugitive emissions of an old coke oven did not comply with the threshold BAP air concentration proposed by the World Health Organization (WHO), up to 1,900 m distance. The study identified the PAH profile of fugitive emissions of a coke oven, statistically different from the profile of traffic emissions. During its activity, in the Genoa residential area, 575 m away from the plant, 92.8% of found PAHs was due to coke oven emission only.

Variable speed controller

NASA Technical Reports Server (NTRS)

Estes, Christa; Spiggle, Charles; Swift, Shannon; Vangeffen, Stephen; Younger, Frank

1992-01-01

This report details a new design for a variable speed controller which can be used to operate lunar machinery without the astronaut using his or her upper body. In order to demonstrate the design, a treadle for an industrial sewing machine was redesigned to be used by a standing operator. Since the invention of an electrically powered sewing machine, the operator has been seated. Today, companies are switching from sit down to stand up operation involving modular stations. The old treadle worked well with a sitting operator, but problems have been found when trying to use the same treadle with a standing operator. Emphasis is placed on the ease of use by the operator along with the ergonomics involved. Included with the design analysis are suggestions for possible uses for the speed controller in other applications.

Aspects of the inverse problem for the Toda chain

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kozlowski, K. K., E-mail: karol.kozlowski@u-bourgogne.fr

We generalize Babelon's approach to equations in dual variables so as to be able to treat new types of operators which we build out of the sub-constituents of the model's monodromy matrix. Further, we also apply Sklyanin's recent monodromy matrix identities so as to obtain equations in dual variables for yet other operators. The schemes discussed in this paper appear to be universal and thus, in principle, applicable to many models solvable through the quantum separation of variables.

Evaluation of SSME test data reduction methods

NASA Technical Reports Server (NTRS)

Santi, L. Michael

1994-01-01

Accurate prediction of hardware and flow characteristics within the Space Shuttle Main Engine (SSME) during transient and main-stage operation requires a significant integration of ground test data, flight experience, and computational models. The process of integrating SSME test measurements with physical model predictions is commonly referred to as data reduction. Uncertainties within both test measurements and simplified models of the SSME flow environment compound the data integration problem. The first objective of this effort was to establish an acceptability criterion for data reduction solutions. The second objective of this effort was to investigate the data reduction potential of the ROCETS (Rocket Engine Transient Simulation) simulation platform. A simplified ROCETS model of the SSME was obtained from the MSFC Performance Analysis Branch . This model was examined and tested for physical consistency. Two modules were constructed and added to the ROCETS library to independently check the mass and energy balances of selected engine subsystems including the low pressure fuel turbopump, the high pressure fuel turbopump, the low pressure oxidizer turbopump, the high pressure oxidizer turbopump, the fuel preburner, the oxidizer preburner, the main combustion chamber coolant circuit, and the nozzle coolant circuit. A sensitivity study was then conducted to determine the individual influences of forty-two hardware characteristics on fourteen high pressure region prediction variables as returned by the SSME ROCETS model.

Observation impact studies with the Mercator Ocean analysis and forecasting systems

NASA Astrophysics Data System (ADS)

Remy, E. D.; Le Traon, P. Y.; Lellouche, J. M.; Drevillon, M.; Turpin, V.; Benkiran, M.

2016-02-01

Mercator Ocean produces and delivers in real-time ocean analysis and forecasts on a daily basis. The quality of the analysis highly relies on the availability and quality of the assimilated observations.Tools are developed to estimate the impact of the present network and to help designing the future evolutions of the observing systems in the context of near real time production of ocean analysis and forecasts. OSE and OSSE are the main approaches used in this context. They allow the assessment of the efficiency of a given data set to constrain the ocean model circulation through the data assimilation process. Illustrations will mainly focus on the present and future evolution of the Argo observation network and altimetry constellation, including the potential impact of future SWOT data. Our systems show clear sensitivities to observation array changes, mainly depending on the specified observation error and regional dynamic. Impact on non observed variables can be important and are important to evaluate. Dedicated diagnostics has to be define to measure the improvements bring by each data set. Alternative approaches to OSE and OSSE are also explored: approximate computation of DFS will be presented and discussed. Limitations of each approach will be discussed in the context of real time operation.

[A study on the thermographic diagnosis of vibration disease of tie-tamper operators in the Japanese National Railways].

PubMed

Hirahata, H

1984-01-01

There have been many studies of thermographic diagnosis of vibration disease, but few of them seem to have discussed tie-tamping machines as a cause. This study focuses on thermographic diagnosis of vibration disease in tie-tamper operators of the Japanese National Railways. In the diagnosis the subject's both hands were immersed in water at 10 degrees C for 3 minutes before being examined. Variables such as season, age, type of vibration tool used and total operating time were considered. These were selected as outside variables and thermographic results as dependent variables, in Quantification Method II. Season and confirmation of vibration disease were found to have a relationship to thermographic scaling, but no such relationship was found for age, type of vibration tool used, or total operating time. A cross-analysis of variables confirmed the relationship with season, and revealed that there were fewer confirmed cases of vibration disease in spring and summer than in fall and winter. It was finally concluded that thermographic analysis is more reliable in colder weather.

Reservoirs performances under climate variability: a case study

NASA Astrophysics Data System (ADS)

Longobardi, A.; Mautone, M.; de Luca, C.

2014-09-01

A case study, the Piano della Rocca dam (southern Italy) is discussed here in order to quantify the system performances under climate variability conditions. Different climate scenarios have been stochastically generated according to the tendencies in precipitation and air temperature observed during recent decades for the studied area. Climate variables have then been filtered through an ARMA model to generate, at the monthly scale, time series of reservoir inflow volumes. Controlled release has been computed considering the reservoir is operated following the standard linear operating policy (SLOP) and reservoir performances have been assessed through the calculation of reliability, resilience and vulnerability indices (Hashimoto et al. 1982), comparing current and future scenarios of climate variability. The proposed approach can be suggested as a valuable tool to mitigate the effects of moderate to severe and persistent droughts periods, through the allocation of new water resources or the planning of appropriate operational rules.

Universal Quantum Computing with Arbitrary Continuous-Variable Encoding.

PubMed

Lau, Hoi-Kwan; Plenio, Martin B

2016-09-02

Implementing a qubit quantum computer in continuous-variable systems conventionally requires the engineering of specific interactions according to the encoding basis states. In this work, we present a unified formalism to conduct universal quantum computation with a fixed set of operations but arbitrary encoding. By storing a qubit in the parity of two or four qumodes, all computing processes can be implemented by basis state preparations, continuous-variable exponential-swap operations, and swap tests. Our formalism inherits the advantages that the quantum information is decoupled from collective noise, and logical qubits with different encodings can be brought to interact without decoding. We also propose a possible implementation of the required operations by using interactions that are available in a variety of continuous-variable systems. Our work separates the "hardware" problem of engineering quantum-computing-universal interactions, from the "software" problem of designing encodings for specific purposes. The development of quantum computer architecture could hence be simplified.

Universal Quantum Computing with Arbitrary Continuous-Variable Encoding

NASA Astrophysics Data System (ADS)

Lau, Hoi-Kwan; Plenio, Martin B.

2016-09-01

Implementing a qubit quantum computer in continuous-variable systems conventionally requires the engineering of specific interactions according to the encoding basis states. In this work, we present a unified formalism to conduct universal quantum computation with a fixed set of operations but arbitrary encoding. By storing a qubit in the parity of two or four qumodes, all computing processes can be implemented by basis state preparations, continuous-variable exponential-swap operations, and swap tests. Our formalism inherits the advantages that the quantum information is decoupled from collective noise, and logical qubits with different encodings can be brought to interact without decoding. We also propose a possible implementation of the required operations by using interactions that are available in a variety of continuous-variable systems. Our work separates the "hardware" problem of engineering quantum-computing-universal interactions, from the "software" problem of designing encodings for specific purposes. The development of quantum computer architecture could hence be simplified.

An EGO-like optimization framework for sensor placement optimization in modal analysis

NASA Astrophysics Data System (ADS)

Morlier, Joseph; Basile, Aniello; Chiplunkar, Ankit; Charlotte, Miguel

2018-07-01

In aircraft design, ground/flight vibration tests are conducted to extract aircraft’s modal parameters (natural frequencies, damping ratios and mode shapes) also known as the modal basis. The main problem in aircraft modal identification is the large number of sensors needed, which increases operational time and costs. The goal of this paper is to minimize the number of sensors by optimizing their locations in order to reconstruct a truncated modal basis of N mode shapes with a high level of accuracy in the reconstruction. There are several methods to solve sensors placement optimization (SPO) problems, but for this case an original approach has been established based on an iterative process for mode shapes reconstruction through an adaptive Kriging metamodeling approach so called efficient global optimization (EGO)-SPO. The main idea in this publication is to solve an optimization problem where the sensors locations are variables and the objective function is defined by maximizing the trace of criteria so called AutoMAC. The results on a 2D wing demonstrate a reduction of sensors by 30% using our EGO-SPO strategy.

Variable stars around selected open clusters in the VVV area: Young Stellar Objects

NASA Astrophysics Data System (ADS)

Medina, Nicolas; Borissova, Jura; Bayo, Amelia; Kurtev, Radostin; Lucas, Philip

2017-09-01

Time-varying phenomena are one of the most substantial sources of astrophysical information, and led to many fundamental discoveries in modern astronomy. We have developed an automated tool to search and analyze variable sources in the near infrared Ks band, using the data from the Vista Variables in the Vía Láctea (VVV) ESO Public Survey ([5, 8]). One of our main goals is to investigate the Young Stellar Objects (YSOs) in the Galactic star forming regions, looking for: •Variability. •New pre-main sequence star clusters. Here we present the newly discovered YSOs within some selected stellar clusters in our Galaxy.

The nature and use of prediction skills in a biological computer simulation

NASA Astrophysics Data System (ADS)

Lavoie, Derrick R.; Good, Ron

The primary goal of this study was to examine the science process skill of prediction using qualitative research methodology. The think-aloud interview, modeled after Ericsson and Simon (1984), let to the identification of 63 program exploration and prediction behaviors.The performance of seven formal and seven concrete operational high-school biology students were videotaped during a three-phase learning sequence on water pollution. Subjects explored the effects of five independent variables on two dependent variables over time using a computer-simulation program. Predictions were made concerning the effect of the independent variables upon dependent variables through time. Subjects were identified according to initial knowledge of the subject matter and success at solving three selected prediction problems.Successful predictors generally had high initial knowledge of the subject matter and were formal operational. Unsuccessful predictors generally had low initial knowledge and were concrete operational. High initial knowledge seemed to be more important to predictive success than stage of Piagetian cognitive development.Successful prediction behaviors involved systematic manipulation of the independent variables, note taking, identification and use of appropriate independent-dependent variable relationships, high interest and motivation, and in general, higher-level thinking skills. Behaviors characteristic of unsuccessful predictors were nonsystematic manipulation of independent variables, lack of motivation and persistence, misconceptions, and the identification and use of inappropriate independent-dependent variable relationships.

11. SAC command center, main operations area, underground structure, building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. SAC command center, main operations area, underground structure, building 501, undated - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Command Center, 901 SAC Boulevard, Bellevue, Sarpy County, NE

9. SAC command center, main operations area, underground structure, building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

9. SAC command center, main operations area, underground structure, building 501, undated - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Command Center, 901 SAC Boulevard, Bellevue, Sarpy County, NE

A new method for defining and managing process alarms and for correcting process operation when an alarm occurs.

PubMed

Brooks, Robin; Thorpe, Richard; Wilson, John

2004-11-11

A new mathematical treatment of alarms that considers them as multi-variable interactions between process variables has provided the first-ever method to calculate values for alarm limits. This has resulted in substantial reductions in false alarms and hence in alarm annunciation rates in field trials. It has also unified alarm management, process control and product quality control into a single mathematical framework so that operations improvement and hence economic benefits are obtained at the same time as increased process safety. Additionally, an algorithm has been developed that advises what changes should be made to Manipulable process variables to clear an alarm. The multi-variable Best Operating Zone at the heart of the method is derived from existing historical data using equation-free methods. It does not require a first-principles process model or an expensive series of process identification experiments. Integral with the method is a new format Process Operator Display that uses only existing variables to fully describe the multi-variable operating space. This combination of features makes it an affordable and maintainable solution for small plants and single items of equipment as well as for the largest plants. In many cases, it also provides the justification for the investments about to be made or already made in process historian systems. Field Trials have been and are being conducted at IneosChlor and Mallinckrodt Chemicals, both in the UK, of the new geometric process control (GPC) method for improving the quality of both process operations and product by providing Process Alarms and Alerts of much high quality than ever before. The paper describes the methods used, including a simple visual method for Alarm Rationalisation that quickly delivers large sets of Consistent Alarm Limits, and the extension to full Alert Management with highlights from the Field Trials to indicate the overall effectiveness of the method in practice.

Worker safety and injury severity analysis of earthmoving equipment accidents.

PubMed

Kazan, Emrah; Usmen, Mumtaz A

2018-06-01

Research on construction worker safety associated with construction equipment has mostly focused on accident type rather than injury severity and the embedded factor relationships. Significant variables and their effects on the degree of injury are examined for earthmoving equipment using data from OSHA. Four types of equipment, backhoe, bulldozer, excavator, and scraper are included in the study. Accidents involving on-foot workers and equipment operators are investigated collectively, as well as separately. Cross tabulation analysis was conducted to establish the associations between selected categorical variables, using degree of injury as a dichotomous dependent variable (fatal vs. nonfatal) and a number of independent variables having different values. Odds ratios were calculated to determine how much a certain variable/factor increases the odds of fatality in an accident, and the odds ratios were ranked to determine the relative impact of a given factor. It was found that twelve variables were significantly associated with injury severity. Rankings based on odds ratios showed that inadequate safety training (2.54), missing equipment protective system (2.38), being a non-union worker (2.26), being an equipment operator (1.93), and being on or around inadequately maintained equipment (1.58) produced higher odds for fatality. A majority of the earthmoving equipment accidents resulted in fatality. Backhoes were the most common equipment involved in accidents and fatalities. Struck-by accidents were the most prevalent and most fatal. Non-OSHA compliant safety training, missing seatbelt, operator not using seatbelt, malfunctioning back-up alarms, and poorly maintained equipment were factors contributing to accidents and fatalities. On-foot workers experienced a higher number of accidents than operators, while fatality odds were higher for the operators. Practical applications: Safety professionals should benefit from our findings in planning and delivering training and providing oversight to workers in earthmoving equipment operations. Copyright © 2018 National Safety Council and Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Z.; Liu, C.; Botterud, A.

Renewable energy resources have been rapidly integrated into power systems in many parts of the world, contributing to a cleaner and more sustainable supply of electricity. Wind and solar resources also introduce new challenges for system operations and planning in terms of economics and reliability because of their variability and uncertainty. Operational strategies based on stochastic optimization have been developed recently to address these challenges. In general terms, these stochastic strategies either embed uncertainties into the scheduling formulations (e.g., the unit commitment [UC] problem) in probabilistic forms or develop more appropriate operating reserve strategies to take advantage of advanced forecastingmore » techniques. Other approaches to address uncertainty are also proposed, where operational feasibility is ensured within an uncertainty set of forecasting intervals. In this report, a comprehensive review is conducted to present the state of the art through Spring 2015 in the area of stochastic methods applied to power system operations with high penetration of renewable energy. Chapters 1 and 2 give a brief introduction and overview of power system and electricity market operations, as well as the impact of renewable energy and how this impact is typically considered in modeling tools. Chapter 3 reviews relevant literature on operating reserves and specifically probabilistic methods to estimate the need for system reserve requirements. Chapter 4 looks at stochastic programming formulations of the UC and economic dispatch (ED) problems, highlighting benefits reported in the literature as well as recent industry developments. Chapter 5 briefly introduces alternative formulations of UC under uncertainty, such as robust, chance-constrained, and interval programming. Finally, in Chapter 6, we conclude with the main observations from our review and important directions for future work.« less

A New Variable Weighting and Selection Procedure for K-Means Cluster Analysis

ERIC Educational Resources Information Center

Steinley, Douglas; Brusco, Michael J.

2008-01-01

A variance-to-range ratio variable weighting procedure is proposed. We show how this weighting method is theoretically grounded in the inherent variability found in data exhibiting cluster structure. In addition, a variable selection procedure is proposed to operate in conjunction with the variable weighting technique. The performances of these…

The generic MESSy submodel TENDENCY (v1.0) for process-based analyses in Earth system models

NASA Astrophysics Data System (ADS)

Eichinger, R.; Jöckel, P.

2014-07-01

The tendencies of prognostic variables in Earth system models are usually only accessible, e.g. for output, as a sum over all physical, dynamical and chemical processes at the end of one time integration step. Information about the contribution of individual processes to the total tendency is lost, if no special precautions are implemented. The knowledge on individual contributions, however, can be of importance to track down specific mechanisms in the model system. We present the new MESSy (Modular Earth Submodel System) infrastructure submodel TENDENCY and use it exemplarily within the EMAC (ECHAM/MESSy Atmospheric Chemistry) model to trace process-based tendencies of prognostic variables. The main idea is the outsourcing of the tendency accounting for the state variables from the process operators (submodels) to the TENDENCY submodel itself. In this way, a record of the tendencies of all process-prognostic variable pairs can be stored. The selection of these pairs can be specified by the user, tailor-made for the desired application, in order to minimise memory requirements. Moreover, a standard interface allows the access to the individual process tendencies by other submodels, e.g. for on-line diagnostics or for additional parameterisations, which depend on individual process tendencies. An optional closure test assures the correct treatment of tendency accounting in all submodels and thus serves to reduce the model's susceptibility. TENDENCY is independent of the time integration scheme and therefore the concept is applicable to other model systems as well. Test simulations with TENDENCY show an increase of computing time for the EMAC model (in a setup without atmospheric chemistry) of 1.8 ± 1% due to the additional subroutine calls when using TENDENCY. Exemplary results reveal the dissolving mechanisms of the stratospheric tape recorder signal in height over time. The separation of the tendency of the specific humidity into the respective processes (large-scale clouds, convective clouds, large-scale advection, vertical diffusion and methane oxidation) show that the upward propagating water vapour signal dissolves mainly because of the chemical and the advective contribution. The TENDENCY submodel is part of version 2.42 or later of MESSy.

The generic MESSy submodel TENDENCY (v1.0) for process-based analyses in Earth System Models

NASA Astrophysics Data System (ADS)

Eichinger, R.; Jöckel, P.

2014-04-01

The tendencies of prognostic variables in Earth System Models are usually only accessible, e.g., for output, as sum over all physical, dynamical and chemical processes at the end of one time integration step. Information about the contribution of individual processes to the total tendency is lost, if no special precautions are implemented. The knowledge on individual contributions, however, can be of importance to track down specific mechanisms in the model system. We present the new MESSy (Modular Earth Submodel System) infrastructure submodel TENDENCY and use it exemplarily within the EMAC (ECHAM/MESSy Atmospheric Chemistry) model to trace process-based tendencies of prognostic variables. The main idea is the outsourcing of the tendency accounting for the state variables from the process operators (submodels) to the TENDENCY submodel itself. In this way, a record of the tendencies of all process-prognostic variable pairs can be stored. The selection of these pairs can be specified by the user, tailor-made for the desired application, in order to minimise memory requirements. Moreover a standard interface allows the access to the individual process tendencies by other submodels, e.g., for on-line diagnostics or for additional parameterisations, which depend on individual process tendencies. An optional closure test assures the correct treatment of tendency accounting in all submodels and thus serves to reduce the models susceptibility. TENDENCY is independent of the time integration scheme and therefore applicable to other model systems as well. Test simulations with TENDENCY show an increase of computing time for the EMAC model (in a setup without atmospheric chemistry) of 1.8 ± 1% due to the additional subroutine calls when using TENDENCY. Exemplary results reveal the dissolving mechanisms of the stratospheric tape recorder signal in height over time. The separation of the tendency of the specific humidity into the respective processes (large-scale clouds, convective clouds, large-scale advection, vertical diffusion and methane-oxidation) show that the upward propagating water vapour signal dissolves mainly because of the chemical and the advective contribution. The TENDENCY submodel is part of version 2.42 or later of MESSy.

Improving perioperative performance: the use of operations management and the electronic health record.

PubMed

Foglia, Robert P; Alder, Adam C; Ruiz, Gardito

2013-01-01

Perioperative services require the orchestration of multiple staff, space and equipment. Our aim was to identify whether the implementation of operations management and an electronic health record (EHR) improved perioperative performance. We compared 2006, pre operations management and EHR implementation, to 2010, post implementation. Operations management consisted of: communication to staff of perioperative vision and metrics, obtaining credible data and analysis, and the implementation of performance improvement processes. The EHR allows: identification of delays and the accountable service or person, collection and collation of data for analysis in multiple venues, including operational, financial, and quality. Metrics assessed included: operative cases, first case on time starts; reason for delay, and operating revenue. In 2006, 19,148 operations were performed (13,545 in the Main Operating Room (OR) area, and 5603, at satellite locations); first case on time starts were 12%; reasons for first case delay were not identifiable; and operating revenue was $115.8M overall, with $78.1M in the Main OR area. In 2010, cases increased to 25,856 (+35%); Main OR area increased to 13,986 (+3%); first case on time starts improved to 46%; operations outside the Main OR area increased to 11,870 (112%); case delays were ascribed to nurses 7%, anesthesiologists 22%, surgeons 33%, and other (patient, hospital) 38%. Five surgeons (7%) accounted for 29% of surgical delays and 4 anesthesiologists (8%) for 45% of anesthesiology delays; operating revenue increased to $177.3M (+53%) overall, and in the Main OR area rose to $101.5M (+30%). The use of operations management and EHR resulted in improved processes, credible data, promptly sharing the metrics, and pinpointing individual provider performance. Implementation of these strategies allowed us to shift cases between facilities, reallocate OR blocks, increase first case on time starts four fold and operative cases by 35%, and these changes were associated with a 53% increase in operating revenue. The fact that revenue increase was greater than case volume (53% vs. 35%) speaks for improved performance. Copyright © 2013 Elsevier Inc. All rights reserved.

Physical associations to spring phytoplankton biomass interannual variability in the U.S. Northeast Continental Shelf

NASA Astrophysics Data System (ADS)

Saba, Vincent S.; Hyde, Kimberly J. W.; Rebuck, Nathan D.; Friedland, Kevin D.; Hare, Jonathan A.; Kahru, Mati; Fogarty, Michael J.

2015-02-01

The continental shelf of the Northeast United States and Nova Scotia is a productive marine ecosystem that supports a robust biomass of living marine resources. Understanding marine ecosystem sensitivity to changes in the physical environment can start with the first-order response of phytoplankton (i.e., chlorophyll a), the base of the marine food web. However, the primary physical associations to the interannual variability of chlorophyll a in these waters are unclear. Here we used ocean color satellite measurements and identified the local and remote physical associations to interannual variability of spring surface chlorophyll a from 1998 to 2013. The highest interannual variability of chlorophyll a occurred in March and April on the northern flank of Georges Bank, the western Gulf of Maine, and Nantucket Shoals. Complex interactions between winter wind speed over the Shelf, local winter water levels, and the relative proportions of Atlantic versus Labrador Sea source waters entering the Gulf of Maine from the previous summer/fall were associated with the variability of March/April chlorophyll a in Georges Bank and the Gulf of Maine. Sea surface temperature and sea surface salinity were not robust correlates to spring chlorophyll a. Surface nitrate in the winter was not a robust correlate to chlorophyll a or the physical variables in every case suggesting that nitrate limitation may not be the primary constraint on the interannual variability of the spring bloom throughout all regions. Generalized linear models suggest that we can resolve 88% of March chlorophyll a interannual variability in Georges Bank using lagged physical data.

How Variables Uncorrelated with the Dependent Variable Can Actually Make Excellent Predictors: The Important Suppressor Variable Case.

ERIC Educational Resources Information Center

Woolley, Kristin K.

Many researchers are unfamiliar with suppressor variables and how they operate in multiple regression analyses. This paper describes the role suppressor variables play in a multiple regression model and provides practical examples that explain how they can change research results. A variable that when added as another predictor increases the total…

COST 734-CLIVAGRI: Impacts of Climate change and Variability on European Agriculture

NASA Astrophysics Data System (ADS)

Orlandini, S.; Nejedlik, P.; Eitzinger, J.; Alexandrov, V.; Toulios, L.; Kajfez Bogataj, L.; Calanca, P.; Trnka, M.; Olesen, J. E.

2009-09-01

COST is an intergovernmental framework for European Cooperation in Science and Technology, funded by its member countries through the EU Framework Programme. The objective of COST is to coordinate, integrate and synthesise results from ongoing national research within and between COST member countries to add value to research investment. COST Actions aim to deliver scientific syntheses and analyses of best available practice to aid problem identification, risk assessment, public utilities and policy development. During 2006, COST Action 734 (CLIVAGRI-Impacts of Climate Change and Variability on European Agriculture) was launched thanks to the coordinated activity of 15 EU countries. The main objective of the Action is the evaluation of possible impacts from climate change and variability on agriculture and the assessment of critical thresholds for various European areas (COST 734 MoU. www.cost.esf.org). Secondary objectives are: the collection and review of existing agroclimatic indices and simulation models, to assess hazard impacts on various European agricultural areas relating hazards to climatic conditions; building climate scenarios for the next few decades; the definition of harmonised criteria to evaluate the impacts of climate change and variability on agriculture; the definition of warning systems guidelines. Four working groups, with the integration of remote sensing sub working group 2.1 were created to address these aims: WG1 - Agroclimatic indices and simulation models WG2 - Evaluation of the current trends of agroclimatic indices and simulation model outputs describing agricultural impacts and hazard levels WG3 - Development and assessment of future regional and local scenarios of agroclimatic conditions WG4 - Risk assessment and foreseen impacts on agriculture The activity of WGs has been structured like a matrix, presenting on the rows the methods of analysis and on the columns the phenomena and the hazards. Each intersection point describes the evaluation of past, present and future trends of climate and thus the impacts on agriculture. Based on these results, possible actions (specific recommendations, suggestions, warning systems) will be elaborated and proposed to the end-users, depending on their needs. At present 28 countries join the Action with the collaboration of Agricultural Meteorology Division - Word Meteorology Organization and Ispra- IPSC- AGRIFISH UNIT - Joint Research Centre. Time schedule of activity includes three main phases: • Planning, operational arrangements, establishment of WGs and inventory. • Main scientific work to be conducted by each WG. • WGs activities to be concluded with emphasis on disseminations, reports and final publications.

Space Transportation Operations: Assessment of Methodologies and Models

NASA Technical Reports Server (NTRS)

Joglekar, Prafulla

2001-01-01

The systems design process for future space transportation involves understanding multiple variables and their effect on lifecycle metrics. Variables such as technology readiness or potential environmental impact are qualitative, while variables such as reliability, operations costs or flight rates are quantitative. In deciding what new design concepts to fund, NASA needs a methodology that would assess the sum total of all relevant qualitative and quantitative lifecycle metrics resulting from each proposed concept. The objective of this research was to review the state of operations assessment methodologies and models used to evaluate proposed space transportation systems and to develop recommendations for improving them. It was found that, compared to the models available from other sources, the operations assessment methodology recently developed at Kennedy Space Center has the potential to produce a decision support tool that will serve as the industry standard. Towards that goal, a number of areas of improvement in the Kennedy Space Center's methodology are identified.

Space Transportation Operations: Assessment of Methodologies and Models

NASA Technical Reports Server (NTRS)

Joglekar, Prafulla

2002-01-01

The systems design process for future space transportation involves understanding multiple variables and their effect on lifecycle metrics. Variables such as technology readiness or potential environmental impact are qualitative, while variables such as reliability, operations costs or flight rates are quantitative. In deciding what new design concepts to fund, NASA needs a methodology that would assess the sum total of all relevant qualitative and quantitative lifecycle metrics resulting from each proposed concept. The objective of this research was to review the state of operations assessment methodologies and models used to evaluate proposed space transportation systems and to develop recommendations for improving them. It was found that, compared to the models available from other sources, the operations assessment methodology recently developed at Kennedy Space Center has the potential to produce a decision support tool that will serve as the industry standard. Towards that goal, a number of areas of improvement in the Kennedy Space Center's methodology are identified.

Classification and ordination of main plant communities along an altitudinal gradient in the arid and temperate climates of northeastern Mexico.

PubMed

Castillón, Eduardo Estrada; Arévalo, José Ramón; Quintanilla, José Ángel Villarreal; Rodríguez, María Magdalena Salinas; Encina-Domínguez, Juan Antonio; Rodríguez, Humberto González; Ayala, César Martín Cantú

2015-10-01

Quantitative data on the ecology of the main plant communities along an altitudinal gradient in northeastern Mexico were obtained with the aim of identifying the most important environmental variables that affect plant distribution and composition. The main threats to these communities were also investigated. Importance value index (IVi) of the 39 most important species and 16 environmental variables were recorded at 35 altitudinal gradients each spaced at intervals of at least 100-m altitude. Classification and ordination of vegetation showed six well-differentiated but overlapping plant communities: alpine meadow, cold conifer forest, mesic mixed forest, xeric scrub, Tamaulipan piedmont scrub, and halophytic grassland. Altitude, minimum and average temperatures, and organic matter content are the main variables affecting the plant distribution in northeastern Mexico. Urban growth, mechanized agriculture, and changes in land use are the main threats in the short and medium term to plant communities in this area. Climate change also seems to be having an impact at present or in the near future as shown by the presence of exotic shrubs from warmer areas in mesic and temperate areas inhabited by oak and oak-pine forest.

Global Risk Score and Clinical SYNTAX Score as Predictors of Clinical Outcomes of Patients Undergoing Unprotected Left Main Percutaneous Catheter Intervention

PubMed Central

Cuenza, Lucky; Collado, Marianne P.; Ho Khe Sui, James

2017-01-01

Background Risk stratification is an important component of left main percutaneous catheter intervention (PCI) which has emerged as a feasible alternative to cardiac surgery. We sought to compare the clinical SYNTAX score and the global risk score in predicting outcomes of patients undergoing unprotected left main PCI in our institution. Methods Clinical, angiographic and procedural characteristics of 92 patients who underwent unprotected left main PCI (mean age 62 ± 12.1 years) were analyzed. Patients were risk stratified into tertiles of high, intermediate and low risk using the global risk score (GRS) and the clinical SYNTAX score (CSS) and were prospectively followed up at 1 year for the occurrence of major adverse cardiovascular events (MACEs), defined as a composite of all cause mortality, cardiac mortality, non-fatal myocardial infarction, stroke, coronary artery bypass, and target vessel revascularization. Results There were 26 (28.2%) who experienced MACEs, of which 10 (10.8%) patients died. Multivariable hazards analysis showed that the GRS (hazard ratio (HR) = 5.5, P = 0.001) and CSS (HR = 4.3, P = 0.001) were both independent predictors of MACEs. Kaplan-Meier analysis showed higher incidence of MACEs with the intermediate and higher risk categories compared to those classified as low risk. Receiver-operator characteristic analysis showed that the GRS has better discriminatory ability than the CSS in the prediction of 1 year MACEs (0.891 vs. 0.743, P = 0.007). Conclusion The GRS and CSS are predictive of outcomes after left main PCI. The GRS appears to have superior predictive and prognostic utility compared to the CSS. This study emphasizes the importance of combining both anatomic and clinical variables for optimum prognostication and management decisions in left main PCI. PMID:29317974

Mesospheric Simulations with the NOGAPS-ALPHA model: Applications to the Summer Polar Mesosphere and AIM data

NASA Astrophysics Data System (ADS)

Siskind, D. E.; Eckermann, S. D.; McCormack, J. P.; Hoppel, K. W.; Russell, J. M.; Bailey, S.; Hervig, M.; Rusch, D.

2007-12-01

The Navy Operational Global Atmospheric Prediction System (NOGAPS), the Department of Defense's global numerical weather prediction (NWP) system, consists of two main components: the Naval Research Laboratory (NRL) Atmospheric Variational Data Assimilation System (NAVDAS) and a global spectral general circulation model (GCM) for forecasting. NRL researchers are currently developing an Advanced-Level Physics High-Altitude (ALPHA) NOGAPS prototype that extends the currently operational 1 hPa upper boundary of NOGAPS through the mesosphere and lower thermosphere (MLT) to ~110 km. We report results of preliminary experiments with this NOGAPS-ALPHA system during May-June 2007, focused on the northern hemisphere (NH) summer mesosphere observed from the Aeronomy of Ice in the Mesosphere (AIM) satellite. These AIM-period NOGAPS-ALPHA experiments have two main goals: to provide global modeling support for AIM science and to allow objective validation of these new NOGAPS-ALPHA MLT fields using independent observations from AIM. We report results of runs which assimilate temperature and water vapor data from the SABER and MLS instruments up to ~0.01 hPa. We investigate the development of the cold NH summer mesopause in NOGAPS-ALPHA and its sensitivity to parameterized nonorographic gravity wave drag (GWD) and radiative heating/cooling by comparing with temperatures and water vapor measured by AIM's SOFIE instrument. We can also compare the variability in the NOGAPS-ALPHA temperature and water vapor fields with mesospheric cloud occurrence statistics measured by CIPS on AIM.

The upgraded data acquisition system for beam loss monitoring at the Fermilab Tevatron and Main Injector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baumbaugh, A.; Briegel, C.; Brown, B.C.

2011-11-01

A VME-based data acquisition system for beam-loss monitors has been developed and is in use in the Tevatron and Main Injector accelerators at the Fermilab complex. The need for enhanced beam-loss protection when the Tevatron is operating in collider-mode was the main driving force for the new design. Prior to the implementation of the present system, the beam-loss monitor system was disabled during collider operation and protection of the Tevatron magnets relied on the quench protection system. The new Beam-Loss Monitor system allows appropriate abort logic and thresholds to be set over the full set of collider operating conditions. Themore » system also records a history of beam-loss data prior to a beam-abort event for post-abort analysis. Installation of the Main Injector system occurred in the fall of 2006 and the Tevatron system in the summer of 2007. Both systems were fully operation by the summer of 2008. In this paper we report on the overall system design, provide a description of its normal operation, and show a number of examples of its use in both the Main Injector and Tevatron.« less

The upgraded data acquisition system for beam loss monitoring at the Fermilab Tevatron and Main Injector

NASA Astrophysics Data System (ADS)

Baumbaugh, A.; Briegel, C.; Brown, B. C.; Capista, D.; Drennan, C.; Fellenz, B.; Knickerbocker, K.; Lewis, J. D.; Marchionni, A.; Needles, C.; Olson, M.; Pordes, S.; Shi, Z.; Still, D.; Thurman-Keup, R.; Utes, M.; Wu, J.

2011-11-01

A VME-based data acquisition system for beam-loss monitors has been developed and is in use in the Tevatron and Main Injector accelerators at the Fermilab complex. The need for enhanced beam-loss protection when the Tevatron is operating in collider-mode was the main driving force for the new design. Prior to the implementation of the present system, the beam-loss monitor system was disabled during collider operation and protection of the Tevatron magnets relied on the quench protection system. The new Beam-Loss Monitor system allows appropriate abort logic and thresholds to be set over the full set of collider operating conditions. The system also records a history of beam-loss data prior to a beam-abort event for post-abort analysis. Installation of the Main Injector system occurred in the fall of 2006 and the Tevatron system in the summer of 2007. Both systems were fully operation by the summer of 2008. In this paper we report on the overall system design, provide a description of its normal operation, and show a number of examples of its use in both the Main Injector and Tevatron.

A Study of Three Phase and Single Phase High Frequency Distribution Systems

DTIC Science & Technology

1989-09-20

single Schwarz converter which operates in a variable frequency mode and acts as a regulated dc power supply . This mode of operation is used to maintain a...conditioning stages. The first stage contains a single Schwarz converter which operates in a variable frequency mode and acts as a regulated dc power supply ...dependent upon the amount of current ripple the capacitor must sink. This determines the capacitor heating since the power dissipated is equal to 2R

Inter-track interference mitigation with two-dimensional variable equalizer for bit patterned media recording

NASA Astrophysics Data System (ADS)

Wang, Yao; Vijaya Kumar, B. V. K.

2017-05-01

The increased track density in bit patterned media recording (BPMR) causes increased inter-track interference (ITI), which degrades the bit error rate (BER) performance. In order to mitigate the effect of the ITI, signals from multiple tracks can be equalized by a 2D equalizer with 1D target. Usually, the 2D fixed equalizer coefficients are obtained by using a pseudo-random bit sequence (PRBS) for training. In this study, a 2D variable equalizer is proposed, where various sets of 2D equalizer coefficients are predetermined and stored for different ITI patterns besides the usual PRBS training. For data detection, as the ITI patterns are unknown in the first global iteration, the main and adjacent tracks are equalized with the conventional 2D fixed equalizer, detected with Bahl-Cocke-Jelinek-Raviv (BCJR) detector and decoded with low-density parity-check (LDPC) decoder. Then using the estimated bit information from main and adjacent tracks, the ITI pattern for each island of the main track can be estimated and the corresponding 2D variable equalizers are used to better equalize the bits on the main track. This process is executed iteratively by feeding back the main track information. Simulation results indicate that for both single-track and two-track detection, the proposed 2D variable equalizer can achieve better BER and frame error rate (FER) compared to that with the 2D fixed equalizer.

Intelligence, Creativity, and Language: An Examination of the Interrelationships of Three Variables among Preschool, Disadvantaged Negro Children.

ERIC Educational Resources Information Center

Lichtman, Marilyn Vickman

The interrelationships among the three variables of intelligence, creativity, and language in a preschool, disadvantaged Negro sample were investigated. The two main hypotheses tested were: (1) The interrelationships among the three variables are lower than the interrelationships within each variable; and (2) A factor analysis indicates a factor…

Contributions of Motivation, Early Numeracy Skills, and Executive Functioning to Mathematical Performance. A Longitudinal Study.

PubMed

Mercader, Jessica; Miranda, Ana; Presentación, M Jesús; Siegenthaler, Rebeca; Rosel, Jesús F

2017-01-01

The main goal of this longitudinal study is to examine the power of different variables and its dynamic interactions in predicting mathematical performance. The model proposed in this study includes indicators of motivational constructs (learning motivation and attributions), executive functioning (inhibition and working memory), and early numeracy skills (logical operations, counting, and magnitude comparison abilities), assessed during kindergarten, and mathematical performance in the second year of Primary Education. The sample consisted of 180 subjects assessed in two moments (5-6 and 7-8 years old). The results showed an indirect effect of initial motivation on later mathematical performance. Executive functioning and early numeracy skills mediated the effect of motivation on later mathematic achievement. Practical implications of these findings for mathematics education are discussed.

Approaches to Evaluating Probability of Collision Uncertainty

NASA Technical Reports Server (NTRS)

Hejduk, Matthew D.; Johnson, Lauren C.

2016-01-01

While the two-dimensional probability of collision (Pc) calculation has served as the main input to conjunction analysis risk assessment for over a decade, it has done this mostly as a point estimate, with relatively little effort made to produce confidence intervals on the Pc value based on the uncertainties in the inputs. The present effort seeks to try to carry these uncertainties through the calculation in order to generate a probability density of Pc results rather than a single average value. Methods for assessing uncertainty in the primary and secondary objects' physical sizes and state estimate covariances, as well as a resampling approach to reveal the natural variability in the calculation, are presented; and an initial proposal for operationally-useful display and interpretation of these data for a particular conjunction is given.

Scaling Up Decision Theoretic Planning to Planetary Rover Problems

NASA Technical Reports Server (NTRS)

Meuleau, Nicolas; Dearden, Richard; Washington, Rich

2004-01-01

Because of communication limits, planetary rovers must operate autonomously during consequent durations. The ability to plan under uncertainty is one of the main components of autonomy. Previous approaches to planning under uncertainty in NASA applications are not able to address the challenges of future missions, because of several apparent limits. On another side, decision theory provides a solid principle framework for reasoning about uncertainty and rewards. Unfortunately, there are several obstacles to a direct application of decision-theoretic techniques to the rover domain. This paper focuses on the issues of structure and concurrency, and continuous state variables. We describes two techniques currently under development that address specifically these issues and allow scaling-up decision theoretic solution techniques to planetary rover planning problems involving a small number of goals.

Modeling a hierarchical structure of factors influencing exploitation policy for water distribution systems using ISM approach

NASA Astrophysics Data System (ADS)

Jasiulewicz-Kaczmarek, Małgorzata; Wyczółkowski, Ryszard; Gładysiak, Violetta

2017-12-01

Water distribution systems are one of the basic elements of contemporary technical infrastructure of urban and rural areas. It is a complex engineering system composed of transmission networks and auxiliary equipment (e.g. controllers, checkouts etc.), scattered territorially over a large area. From the water distribution system operation point of view, its basic features are: functional variability, resulting from the need to adjust the system to temporary fluctuations in demand for water and territorial dispersion. The main research questions are: What external factors should be taken into account when developing an effective water distribution policy? Does the size and nature of the water distribution system significantly affect the exploitation policy implemented? These questions have shaped the objectives of research and the method of research implementation.

Contributions of Motivation, Early Numeracy Skills, and Executive Functioning to Mathematical Performance. A Longitudinal Study

PubMed Central

Mercader, Jessica; Miranda, Ana; Presentación, M. Jesús; Siegenthaler, Rebeca; Rosel, Jesús F.

2018-01-01

The main goal of this longitudinal study is to examine the power of different variables and its dynamic interactions in predicting mathematical performance. The model proposed in this study includes indicators of motivational constructs (learning motivation and attributions), executive functioning (inhibition and working memory), and early numeracy skills (logical operations, counting, and magnitude comparison abilities), assessed during kindergarten, and mathematical performance in the second year of Primary Education. The sample consisted of 180 subjects assessed in two moments (5–6 and 7–8 years old). The results showed an indirect effect of initial motivation on later mathematical performance. Executive functioning and early numeracy skills mediated the effect of motivation on later mathematic achievement. Practical implications of these findings for mathematics education are discussed. PMID:29379462

Enhanced perceptual functioning in autism: an update, and eight principles of autistic perception.

PubMed

Mottron, Laurent; Dawson, Michelle; Soulières, Isabelle; Hubert, Benedicte; Burack, Jake

2006-01-01

We propose an "Enhanced Perceptual Functioning" model encompassing the main differences between autistic and non-autistic social and non-social perceptual processing: locally oriented visual and auditory perception, enhanced low-level discrimination, use of a more posterior network in "complex" visual tasks, enhanced perception of first order static stimuli, diminished perception of complex movement, autonomy of low-level information processing toward higher-order operations, and differential relation between perception and general intelligence. Increased perceptual expertise may be implicated in the choice of special ability in savant autistics, and in the variability of apparent presentations within PDD (autism with and without typical speech, Asperger syndrome) in non-savant autistics. The overfunctioning of brain regions typically involved in primary perceptual functions may explain the autistic perceptual endophenotype.

10. SAC command center, main operations area, underground structure, building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. SAC command center, main operations area, underground structure, building 501, circa 1980 - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Command Center, 901 SAC Boulevard, Bellevue, Sarpy County, NE

12. SAC command center, main operations area, underground structure, building ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. SAC command center, main operations area, underground structure, building 501, circa 1960 - Offutt Air Force Base, Strategic Air Command Headquarters & Command Center, Command Center, 901 SAC Boulevard, Bellevue, Sarpy County, NE

Unravelling the architecture of functional variability in wild populations of Polygonum viviparum L

PubMed Central

Boucher, Florian C.; Thuiller, Wilfried; Arnoldi, Cindy; Albert, Cécile H.; Lavergne, Sébastien

2014-01-01

SUMMARY Functional variability (FV) of populations can be decomposed into three main features: the individual variability of multiple traits, the strength of correlations between those traits and the main direction of these correlations, the latter two being known as ‘phenotypic integration’. Evolutionary biology has long recognized that FV in natural populations is key to determining potential evolutionary responses, but this topic has been little studied in functional ecology. Here we focus on the arctico-alpine perennial plant species Polygonum viviparum L.. We used a comprehensive sampling of seven functional traits in 29 wild populations covering the whole environmental niche of the species. The niche of the species was captured by a temperature gradient, which separated alpine stressful habitats from species-rich, competitive sub-alpine ones. We seeked to assess the relative roles of abiotic stress and biotic interactions in shaping different aspects of functional variation within and among populations, that is, the multi-trait variability, the strength of correlations between traits, and the main directions of functional trade-offs. Populations with the highest extent of functional variability were found in the warm end of the gradient whereas populations exhibiting the strongest degree of phenotypic integration were located in sites with intermediate temperatures. This could reveal both the importance of environmental filtering and population demography in structuring FV. Interestingly, we found that the main axes of multivariate functional variation were radically different within and across population. Although the proximate causes of FV structure remain uncertain, our study presents a robust methodology for the quantitative study of functional variability in connection with species’ niches. It also opens up new perspectives for the conceptual merging of intraspecific functional patterns with community ecology. PMID:24790285

3D FE simulation of semi-finishing machining of Ti6Al4V additively manufactured by direct metal laser sintering

NASA Astrophysics Data System (ADS)

Imbrogno, Stano; Rinaldi, Sergio; Raso, Antonio; Bordin, Alberto; Bruschi, Stefania; Umbrello, Domenico

2018-05-01

The Additive Manufacturing techniques are gaining more and more interest in various industrial fields due to the possibility of drastically reduce the material waste during the production processes, revolutionizing the standard scheme and strategies of the manufacturing processes. However, the metal parts shape produced, frequently do not satisfy the tolerances as well as the surface quality requirements. During the design phase, the finite element simulation results a fundamental tool to help the engineers in the correct decision of the most suitable process parameters, especially in manufacturing processes, in order to produce products of high quality. The aim of this work is to develop a 3D finite element model of semi-finishing turning operation of Ti6Al4V, produced via Direct Metal Laser Sintering (DMLS). A customized user sub-routine was built-up in order to model the mechanical behavior of the material under machining operations to predict the main fundamental variables as cutting forces and temperature. Moreover, the machining induced alterations are also studied by the finite element model developed.

Outdoor field experience with autonomous RPC based stations

NASA Astrophysics Data System (ADS)

Lopes, L.; Assis, P.; Blanco, A.; Carolino, N.; Cerda, M. A.; Conceição, R.; Cunha, O.; Ferreira, M.; Fonte, P.; Luz, R.; Mendes, L.; Pereira, A.; Pimenta, M.; Sarmento, R.; Tomé, B.

2016-09-01

In the last two decades Resistive Plate Chambers were employed in the Cosmic Ray Experiments COVER-PLASTEX and ARGO/YBJ. In both experiments the detectors were housed indoors, likely owing to gas distribution requirements and the need to control environment variables that directly affect RPCs operational stability. But in experiments where Extended Air Shower (EAS) sampling is necessary, large area arrays composed by dispersed stations are deployed, rendering this kind of approach impossible. In this situation, it would be mandatory to have detectors that could be deployed in small standalone stations, with very rare opportunities for maintenance, and with good resilience to environmental conditions. Aiming to meet these requirements, we started some years ago the development of RPCs for Autonomous Stations. The results from indoor tests and measurements were very promising, both concerning performance and stability under very low gas flow rate, which is the main requirement for Autonomous Stations. In this work we update the indoor results and show the first ones concerning outdoor stable operation. In particular, a dynamic adjustment of the high voltage is applied to keep gas gain constant.

High performance alloy electroforming

NASA Technical Reports Server (NTRS)

Malone, G. A.; Winkelman, D. M.

1989-01-01

Electroformed copper and nickel are used in structural applications for advanced propellant combustion chambers. An improved process has been developed by Bell Aerospace Textron, Inc. wherein electroformed nickel-manganese alloy has demonstrated superior mechanical and thermal stability when compared to previously reported deposits from known nickel plating processes. Solution chemistry and parametric operating procedures are now established and material property data is established for deposition of thick, large complex shapes such as the Space Shuttle Main Engine. The critical operating variables are those governing the ratio of codeposited nickel and manganese. The deposition uniformity which in turn affects the manganese concentration distribution is affected by solution resistance and geometric effects as well as solution agitation. The manganese concentration in the deposit must be between 2000 and 3000 ppm for optimum physical properties to be realized. The study also includes data regarding deposition procedures for achieving excellent bond strength at an interface with copper, nickel-manganese or INCONEL 718. Applications for this electroformed material include fabrication of complex or re-entry shapes which would be difficult or impossible to form from high strength alloys such as INCONEL 718.

Cross-cultural comparison of political leaders' operational codes.

PubMed

Dirilen-Gumus, Ozlem

2017-12-01

This study aims at comparing operational codes (namely, philosophical and instrumental beliefs about the political universe) of political leaders from different cultures. According to Schwartz (2004), cultures can be categorised into 3 dimensions: autonomy-embeddedness, egalitarianism-hierarchy and mastery-harmony. This study draws upon the 1st dimension (akin to the most popular cultural dimension of Hofstede: individualism-collectivism) and focuses on comparing the leaders of autonomous and embedded cultures based on how cooperative/conflictual they are. The main research hypothesis is as follows: the leaders of embedded cultures would be more cooperative than the leaders of autonomous cultures. For this purpose, 3 autonomous cultures (the UK, Canada and Australia) and embedded cultures (Singapore, South Africa and Malaysia) cultures were chosen randomly and the cooperativeness of the correspondent countries' leaders were compared after being profiled by Profiler Plus. The results indicated that the leaders of embedded cultures were significantly more cooperative than autonomous cultures after holding the control variables constant. The findings were discussed in the light of relevant literature. © 2016 International Union of Psychological Science.

Divertor tungsten tile melting and its effect on core plasma performance

NASA Astrophysics Data System (ADS)

Lipschultz, B.; Coenen, J. W.; Barnard, H. S.; Howard, N. T.; Reinke, M. L.; Whyte, D. G.; Wright, G. M.

2012-12-01

For the 2007 and 2008 run campaigns, Alcator C-Mod operated with a full toroidal row of tungsten tiles in the high heat flux region of the outer divertor; tungsten levels in the core plasma were below measurement limits. An accidental creation of a tungsten leading edge in the 2009 campaign led to this study of a melting tungsten source: H-mode operation with strike point in the region of the melting tile was immediately impossible due to some fraction of tungsten droplets reaching the main plasma. Approximately 15 g of tungsten was lost from the tile over ˜100 discharges. Less than 1% of the evaporated tungsten was found re-deposited on surfaces, the rest is assumed to have become dust. The strong discharge variability of the tungsten reaching the core implies that the melt layer topology is always varying. There is no evidence of healing of the surface with repeated melting. Forces on the melted tungsten tend to lead to prominences that extend further into the plasma. A discussion of the implications of melting a divertor tungsten monoblock on the ITER plasma is presented.

Microgrid Optimal Scheduling With Chance-Constrained Islanding Capability

DOE PAGES

Liu, Guodong; Starke, Michael R.; Xiao, B.; ...

2017-01-13

To facilitate the integration of variable renewable generation and improve the resilience of electricity sup-ply in a microgrid, this paper proposes an optimal scheduling strategy for microgrid operation considering constraints of islanding capability. A new concept, probability of successful islanding (PSI), indicating the probability that a microgrid maintains enough spinning reserve (both up and down) to meet local demand and accommodate local renewable generation after instantaneously islanding from the main grid, is developed. The PSI is formulated as mixed-integer linear program using multi-interval approximation taking into account the probability distributions of forecast errors of wind, PV and load. With themore » goal of minimizing the total operating cost while preserving user specified PSI, a chance-constrained optimization problem is formulated for the optimal scheduling of mirogrids and solved by mixed integer linear programming (MILP). Numerical simulations on a microgrid consisting of a wind turbine, a PV panel, a fuel cell, a micro-turbine, a diesel generator and a battery demonstrate the effectiveness of the proposed scheduling strategy. Lastly, we verify the relationship between PSI and various factors.« less

Design and performance of a rugged standard operative temperature thermometer for avian studies

USGS Publications Warehouse

Bakken, G.S.; Boysen, A.F.; Korschgen, C.E.; Kenow, K.P.; Lima, S.L.

2001-01-01

The lack of a truly satisfactory sensor which can characterize the thermal environment at the spatial scale experienced by small endotherms has hindered study of their thermoregulatory behavior. We describe a general design for a rugged, easily constructed sensor to measure standard operative temperature, Tes. We present specific designs for adult dark-eyed juncos (Junco hyemalis) and hatchling mallards (Anas platyrhynchos). Sensor response was stable and repeatable (??1.4%) over the course of several months. Over the range of conditions for which validation data were available (variable air temperature and wind with negligible net radiation), sensors predicted the mean net heat production of live animals to within ??0.023W (equivalent to ??1??C at Tes= 15??C). The main limit on accuracy was scatter in the data on metabolism and evaporative water loss in live animals. These sensors are far more rugged and easily constructed than the heated taxidermic mounts previously used to measure Tes. These characteristics facilitate the use of significant numbers of sensors in thermal mapping studies of endotherms. ?? 2001 Elsevier Science Ltd. All rights reserved.

PWV, Temperature and Wind Statistics at Sites Suitable For mm and Sub-mm Wavelengths Astronomy

NASA Astrophysics Data System (ADS)

Otarola, Angel; Travouillon, Tony; De Breuck, Carlos; Radford, Simon; Matsushita, Satoki; Pérez-Beaupuits, Juan P.

2018-01-01

Atmospheric water vapor is the main limiting factor of atmospheric transparency in the mm and sub-mm wavelength spectral windows. Thus, dry sites are needed for the installation and successful operation of radio astronomy observatories exploiting those spectral windows. Other parameters that play an important role in the mechanical response of radio telescopes exposed to the environmental conditions are: temperature, and in particular temperature gradients that induce thermal deformation of mechanical structures, as well as wind magnitude that induce pointing jitter affecting this way the required accuracy in the ability to point to a cosmic source during the observations. Temperature and wind are variables of special consideration when planning the installation and operations of large aperture radio telescopes. This work summarizes the statistics of precipitable water vapor (PWV), temperature and wind monitored at sites by the costal mountain range, as well as on t he west slope of the Andes mountain range in the region of Antofagasta, Chile. This information could prove useful for the planning of the Atacama Large-Aperture Submm/mm Telescope (AtLast).

Production of Copper as a Complex Mining and Metallurgical Processing System in Polish Copper Mines of the Legnica-Glogów Copper Belt

NASA Astrophysics Data System (ADS)

Malewski, Jerzy

2017-12-01

Geological and technological conditions of Cu production in the Polish copper mines of the Legnica-Glogów Copper Belt are presented. Cu production is recognized as a technological fractal consisting of subsystems for mineral exploration, ore extraction and processing, and metallurgical treatment. Qualitative and quantitative models of these operations have been proposed, including estimation of their costs of process production. Numerical calculations of such a system have been performed, which allow optimize the system parameters according to economic criteria under variable Cu mineralization in the ore deposit. The main objective of the study is to develop forecasting tool for analysis of production efficiency in domestic copper mines based on available sources of information. Such analyses are primarily of social value, allowing for assessment of the efficiency of management of local mineral resources in the light of current technological and market constraints. At the same time, this is a concept of the system analysis method to manage deposit exploitation on operational and strategic level.

Optimal design of solid oxide fuel cell, ammonia-water single effect absorption cycle and Rankine steam cycle hybrid system

NASA Astrophysics Data System (ADS)

Mehrpooya, Mehdi; Dehghani, Hossein; Ali Moosavian, S. M.

2016-02-01

A combined system containing solid oxide fuel cell-gas turbine power plant, Rankine steam cycle and ammonia-water absorption refrigeration system is introduced and analyzed. In this process, power, heat and cooling are produced. Energy and exergy analyses along with the economic factors are used to distinguish optimum operating point of the system. The developed electrochemical model of the fuel cell is validated with experimental results. Thermodynamic package and main parameters of the absorption refrigeration system are validated. The power output of the system is 500 kW. An optimization problem is defined in order to finding the optimal operating point. Decision variables are current density, temperature of the exhaust gases from the boiler, steam turbine pressure (high and medium), generator temperature and consumed cooling water. Results indicate that electrical efficiency of the combined system is 62.4% (LHV). Produced refrigeration (at -10 °C) and heat recovery are 101 kW and 22.1 kW respectively. Investment cost for the combined system (without absorption cycle) is about 2917 kW-1.

Permanent split capacitor single phase electric motor system

DOEpatents

Kirschbaum, Herbert S.

1984-01-01

A permanent split capacitor single phase electric motor achieves balanced operation at more than one operating point by adjusting the voltage supplied to the main and auxiliary windings and adjusting the capacitance in the auxiliary winding circuit. An intermediate voltage tap on an autotransformer supplies voltage to the main winding for low speed operation while a capacitive voltage divider is used to adjust the voltage supplied to the auxiliary winding for low speed operation.

Transferring Control of the Mand to the Motivating Operation in Children with Autism

ERIC Educational Resources Information Center

Sweeney-Kerwin, Emily J.; Carbone, Vincent J.; O'Brien, Leigh; Zecchin, Gina; Janecky, Marietta N.

2007-01-01

Few studies have made use of B. F. Skinner's (1957) behavioral analysis of language and precise taxonomy of verbal behavior when describing the controlling variables for the mand relation. Consequently, the motivating operation (MO) has not typically been identified as an independent variable and the nature of a spontaneous mand has been…

A variable-gain output feedback control design approach

NASA Technical Reports Server (NTRS)

Haylo, Nesim

1989-01-01

A multi-model design technique to find a variable-gain control law defined over the whole operating range is proposed. The design is formulated as an optimal control problem which minimizes a cost function weighing the performance at many operating points. The solution is obtained by embedding into the Multi-Configuration Control (MCC) problem, a multi-model robust control design technique. In contrast to conventional gain scheduling which uses a curve fit of single model designs, the optimal variable-gain control law stabilizes the plant at every operating point included in the design. An iterative algorithm to compute the optimal control gains is presented. The methodology has been successfully applied to reconfigurable aircraft flight control and to nonlinear flight control systems.

Justifying scale type for a latent variable: Formative or reflective?

NASA Astrophysics Data System (ADS)

Liu, Hao; Bahron, Arsiah; Bagul, Awangku Hassanal Bahar Pengiran

2015-12-01

The study attempted to explore the possibilities to create a procedure at the experimental level to double confirm whether manifest variables scale type is formative or reflective. Now, the criteria of making such a decision are heavily depended on researchers' judgment at the conceptual and operational level. The study created an experimental procedure that seems could double confirm the decisions from the conceptual and operational level judgments. The experimental procedure includes the following tests, Variance Inflation Factor (VIF), Tolerance (TOL), Ridge Regression, Cronbach's alpha, Dillon-Goldstein's rho, and first and second eigenvalue. The procedure considers manifest variables' both multicollinearity and consistency. As the result, the procedure received the same judgment with the carefully established decision making at the concept and operational level.

Remote sensing and avian influenza: A review of image processing methods for extracting key variables affecting avian influenza virus survival in water from Earth Observation satellites

NASA Astrophysics Data System (ADS)

Tran, Annelise; Goutard, Flavie; Chamaillé, Lise; Baghdadi, Nicolas; Lo Seen, Danny

2010-02-01

Recent studies have highlighted the potential role of water in the transmission of avian influenza (AI) viruses and the existence of often interacting variables that determine the survival rate of these viruses in water; the two main variables are temperature and salinity. Remote sensing has been used to map and monitor water bodies for several decades. In this paper, we review satellite image analysis methods used for water detection and characterization, focusing on the main variables that influence AI virus survival in water. Optical and radar imagery are useful for detecting water bodies at different spatial and temporal scales. Methods to monitor the temperature of large water surfaces are also available. Current methods for estimating other relevant water variables such as salinity, pH, turbidity and water depth are not presently considered to be effective.

Wind-tunnel Tests of the Fowler Variable-area Wing

NASA Technical Reports Server (NTRS)

Weick, Fred E; Platt, Robert C

1932-01-01

The lift, drag, and center of pressure characteristics of a model of the Fowler variable-area wing were measured in the NACA 7 by 10 foot wind tunnel. The Fowler wing consists of a combination of a main wing and an extension surface, also of airfoil section. The extension surface can be entirely retracted within the lower rear portion of the main wing or it can be moved to the rear and downward. The tests were made with the nose of the extension airfoil in various positions near the trailing edge of the main wing and with the surface at various angular deflections. The highest lift coefficient obtained was C(sub L) = 3.17 as compared with 1.27 for the main wing alone.

Statistical and Spectral Analysis of Wind Characteristics Relevant to Wind Energy Assessment Using Tower Measurements in Complex Terrain

DOE PAGES

Belu, Radian; Koracin, Darko

2013-01-01

The main objective of the study was to investigate spatial and temporal characteristics of the wind speed and direction in complex terrain that are relevant to wind energy assessment and development, as well as to wind energy system operation, management, and grid integration. Wind data from five tall meteorological towers located in Western Nevada, USA, operated from August 2003 to March 2008, used in the analysis. The multiannual average wind speeds did not show significant increased trend with increasing elevation, while the turbulence intensity slowly decreased with an increase were the average wind speed. The wind speed and direction weremore » modeled using the Weibull and the von Mises distribution functions. The correlations show a strong coherence between the wind speed and direction with slowly decreasing amplitude of the multiday periodicity with increasing lag periods. The spectral analysis shows significant annual periodicity with similar characteristics at all locations. The relatively high correlations between the towers and small range of the computed turbulence intensity indicate that wind variability is dominated by the regional synoptic processes. Knowledge and information about daily, seasonal, and annual wind periodicities are very important for wind energy resource assessment, wind power plant operation, management, and grid integration.« less

High-Performance Integrated Control of water quality and quantity in urban water reservoirs

NASA Astrophysics Data System (ADS)

Galelli, S.; Castelletti, A.; Goedbloed, A.

2015-11-01

This paper contributes a novel High-Performance Integrated Control framework to support the real-time operation of urban water supply storages affected by water quality problems. We use a 3-D, high-fidelity simulation model to predict the main water quality dynamics and inform a real-time controller based on Model Predictive Control. The integration of the simulation model into the control scheme is performed by a model reduction process that identifies a low-order, dynamic emulator running 4 orders of magnitude faster. The model reduction, which relies on a semiautomatic procedural approach integrating time series clustering and variable selection algorithms, generates a compact and physically meaningful emulator that can be coupled with the controller. The framework is used to design the hourly operation of Marina Reservoir, a 3.2 Mm3 storm-water-fed reservoir located in the center of Singapore, operated for drinking water supply and flood control. Because of its recent formation from a former estuary, the reservoir suffers from high salinity levels, whose behavior is modeled with Delft3D-FLOW. Results show that our control framework reduces the minimum salinity levels by nearly 40% and cuts the average annual deficit of drinking water supply by about 2 times the active storage of the reservoir (about 4% of the total annual demand).

Is urgent coronary artery bypass grafting a safe option in octogenarians? A developing country perspective.

PubMed

Luqman, Zubair; Ansari, Junaid; Siddiqui, Fahad Javaid; Sami, Shahid Ahmed

2009-09-01

Life expectancy has increased during recent decades leading to a growing number of older population. The objective of this study was to evaluate the outcomes of coronary artery bypass grafting (CABG) in octogenarians and to compare the outcomes of the emergent CABG with elective surgery. Prospectively collected data from 31 consecutive octogenarian patients who underwent CABG between 1 January 2006 and 31 December 2008 were analyzed. Main outcomes of interest included mortality, length of ICU stay, length of hospital stay, priority of surgery, postoperative complications and functional status on follow-up. Fifteen patients were operated on an urgent basis. Patients operated on an urgent basis were in NYHA class III or IV preoperatively (P=0.0016). There were no significant differences in operative and postoperative variables. There were three in-hospital deaths and 23 patients (82%) were alive on follow-up and 19 were in functional class I or II. Quality of life assessment was performed using Seattle Angina Questionnaire and patients reported remarkable improvement in quality of life. Overall, 90% patients were not or slightly disabled in their daily activity. Satisfaction with their current quality of life was reported by 95% of patients. CABG may be performed in octogenarians with remarkable outcomes and improvement in quality of life.

Comparative Evaluation of Immediate Post-Operative Sequelae after Surgical Removal of Impacted Mandibular Third Molar with or without Tube Drain - Split-Mouth Study.

PubMed

Kumar, Barun; Bhate, Kalyani; Dolas, R S; Kumar, Sn Santhosh; Waknis, Pushkar

2016-12-01

Third molar surgery is one of the most common surgical procedures performed in general dentistry. Post-operative variables such as pain, swelling and trismus are major concerns after impacted mandibular third molar surgery. Use of passive tube drain is supposed to help reduce these immediate post-operative sequelae. The current study was designed to compare the effect of tube drain on immediate post-operative sequelae following impacted mandibular third molar surgery. To compare the post-operative sequelae after surgical removal of impacted mandibular third molar surgery with or without tube drain. Thirty patients with bilateral impacted mandibular third molars were divided into two groups: Test (with tube drain) and control (without tube drain) group. In the test group, a tube drain was inserted through the releasing incision, and kept in place for three days. The control group was left without a tube drain. The post-operative variables like, pain, swelling, and trismus were calculated after 24 hours, 72 hours, 7 days, and 15 days in both the groups and analyzed statistically using chi-square and t-test analysis. The test group showed lesser swelling as compared to control group, with the swelling variable showing statistically significant difference at post-operative day 3 and 7 (p≤ 0.05) in both groups. There were no statistically significant differences in pain and trismus variables in both the groups. The use of tube drain helps to control swelling following impacted mandibular third molar surgery. However, it does not have much effect on pain or trismus.

An Extensive Census of Hubble Space Telescope Counterparts to Chandra X-Ray Sources in the Globular Cluster 47 Tucanae. I. Astrometry and Photometry

NASA Astrophysics Data System (ADS)

Edmonds, Peter D.; Gilliland, Ronald L.; Heinke, Craig O.; Grindlay, Jonathan E.

2003-10-01

We report in this study of 47 Tucanae the largest number of optical identifications of X-ray sources yet obtained in a single globular cluster. Using deep Chandra ACIS-I imaging and extensive Hubble Space Telescope studies with Wide Field Planetary Camera 2 (WFPC2; including a 120 orbit program giving superb V and I images), we have detected optical counterparts to at least 22 cataclysmic variables (CVs) and 29 chromospherically active binaries (BY Dra and RS CVn systems) in 47 Tuc. These identifications are all based on tight astrometric matches between X-ray sources and objects with unusual (non-main-sequence [non-MS]) optical colors and/or optical variability. Several other CVs and active binaries have likely been found, but these have marginal significance because of larger offsets between the X-ray and optical positions, or colors and variability that are not statistically convincing. These less secure optical identifications are not subsequently discussed in detail. In the U versus U-V color-magnitude diagram (CMD), where the U band corresponds to either F336W or F300W, the CVs all show evidence for blue colors compared with the MS, but most of them fall close to the main sequence in the V versus V-I CMD, showing that the secondary stars dominate the optical light. The X-ray-detected active binaries have magnitude offsets above the MS (in both the U versus U-V or V versus V-I CMDs) that are indistinguishable from those of the much larger sample of optical variables (eclipsing and contact binaries and BY Dra variables) detected in the recent WFPC2 studies of Albrow et al. We also present the results of a new, deeper search for optical companions to millisecond pulsars (MSPs). One possible optical companion to an MSP (47 Tuc T) was found, adding to the two optical companions already known. Finally, we study several blue stars with periodic variability from Albrow et al. that show little or no evidence for X-ray emission. The optical colors of these objects differ from those of 47 Tuc (and field) CVs. An accompanying paper will present time series results for these optical identifications and will discuss X-ray-to-optical flux ratios, spatial distributions, and an overall interpretation of the results. Based on observations with the NASA/ESA Hubble Space Telescope obtained at STScI, which is operated by AURA, Inc., under NASA contract NAS 5-26555.

Evaluation of solar irradiance models for climate studies

NASA Astrophysics Data System (ADS)

Ball, William; Yeo, Kok-Leng; Krivova, Natalie; Solanki, Sami; Unruh, Yvonne; Morrill, Jeff

2015-04-01

Instruments on satellites have been observing both Total Solar Irradiance (TSI) and Spectral Solar Irradiance (SSI), mainly in the ultraviolet (UV), since 1978. Models were developed to reproduce the observed variability and to compute the variability at wavelengths that were not observed or had an uncertainty too high to determine an accurate rotational or solar cycle variability. However, various models and measurements show different solar cycle SSI variability that lead to different modelled responses of ozone and temperature in the stratosphere, mainly due to the different UV variability in each model, and the global energy balance. The NRLSSI and SATIRE-S models are the most comprehensive reconstructions of solar irradiance variability for the period from 1978 to the present day. But while NRLSSI and SATIRE-S show similar solar cycle variability below 250 nm, between 250 and 400 nm SATIRE-S typically displays 50% larger variability, which is however, still significantly less then suggested by recent SORCE data. Due to large uncertainties and inconsistencies in some observational datasets, it is difficult to determine in a simple way which model is likely to be closer to the true solar variability. We review solar irradiance variability measurements and modelling and employ new analysis that sheds light on the causes of the discrepancies between the two models and with the observations.

Multi-pass amplifier architecture for high power laser systems

DOEpatents

Manes, Kenneth R; Spaeth, Mary L; Erlandson, Alvin C

2014-04-01

A main amplifier system includes a first reflector operable to receive input light through a first aperture and direct the input light along an optical path. The input light is characterized by a first polarization. The main amplifier system also includes a first polarizer operable to reflect light characterized by the first polarization state. The main amplifier system further includes a first and second set of amplifier modules. Each of the first and second set of amplifier modules includes an entrance window, a quarter wave plate, a plurality of amplifier slablets arrayed substantially parallel to each other, and an exit window. The main amplifier system additionally includes a set of mirrors operable to reflect light exiting the first set of amplifier modules to enter the second set of amplifier modules and a second polarizer operable to reflect light characterized by a second polarization state.

Statistical results on restorative dentistry experiments: effect of the interaction between main variables

PubMed Central

CAVALCANTI, Andrea Nóbrega; MARCHI, Giselle Maria; AMBROSANO, Gláucia Maria Bovi

2010-01-01

Statistical analysis interpretation is a critical field in scientific research. When there is more than one main variable being studied in a research, the effect of the interaction between those variables is fundamental on experiments discussion. However, some doubts can occur when the p-value of the interaction is greater than the significance level. Objective To determine the most adequate interpretation for factorial experiments with p-values of the interaction nearly higher than the significance level. Materials and methods The p-values of the interactions found in two restorative dentistry experiments (0.053 and 0.068) were interpreted in two distinct ways: considering the interaction as not significant and as significant. Results Different findings were observed between the two analyses, and studies results became more coherent when the significant interaction was used. Conclusion The p-value of the interaction between main variables must be analyzed with caution because it can change the outcomes of research studies. Researchers are strongly advised to interpret carefully the results of their statistical analysis in order to discuss the findings of their experiments properly. PMID:20857003

Time Resolved X-Ray Spectral Analysis of Class II YSOs in NGC 2264 During Optical Dips and Bursts

NASA Astrophysics Data System (ADS)

Guarcello, Mario Giuseppe; Flaccomio, Ettore; Micela, Giuseppina; Argiroffi, Costanza; Venuti, Laura

2016-07-01

Pre-Main Sequence stars are variable sources. The main mechanisms responsible for their variability are variable extinction, unsteady accretion, and rotational modulation of both hot and dark photospheric spots and X-ray active regions. In stars with disks this variability is thus related to the morphology of the inner circumstellar region (<0.1 AU) and that of photosphere and corona, all impossible to be spatially resolved with present day techniques. This has been the main motivations of the Coordinated Synoptic Investigation of NGC2264, a set of simultaneous observations of NGC2264 with 15 different telescopes.We analyze the X-ray spectral properties of stars with disks extracted during optical bursts and dips in order to unveil the nature of these phenomena. Stars are analyzed in two different samples. In stars with variable extinction a simultaneous increase of optical extinction and X-ray absorption is searched during the optical dips; in stars with accretion bursts we search for soft X-ray emission and increasing X-ray absorption during the bursts. In 9/33 stars with variable extinction we observe simultaneous increase of X-ray absorption and optical extinction. In seven dips it is possible to calculate the NH/AV ratio in order to infer the composition of the obscuring material. In 5/27 stars with optical accretion bursts, we observe soft X-ray emission during the bursts that we associate to the emission of accreting gas. It is not surprising that these properties are not observed in all the stars with dips and bursts since favorable geometric configurations are required. The observed variable absorption during the dips is mainly due to dust-free material in accretion streams. In stars with accretion bursts we observe in average a larger soft X-ray spectral component not observed in non accreting stars. This indicates that this soft X-ray emission arises from the accretion shocks.

77 FR 12909 - Eastern Maine Railway Company-Assignment of Trackage Rights Exemption-Montreal, Maine & Atlantic...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-02

.... (MMA) has agreed to assign its overhead trackage rights to the Eastern Maine Railway Company (EMR) over... from MMA and to operate 28.75 miles of rail line. MMA, the former owner of the Line, proposed to... operator.\\3\\ In anticipation of MNRC service, MMA acquired trackage rights over the Line to continue to...

Plankton Dynamics and Mesoscale Turbulence

DTIC Science & Technology

2010-06-29

transformation of inorganic materials and light into living matter by photosynthesis ) is operated mainly by small, unicellular algae that float freely in the...ecosystems, primary production (the transformation of inorganic materials and light into living matter by photosynthesis ) is operated mainly by small...them into biomass via photosynthesis . The main limiting factors for phytoplankton growth are light and nutrient availability; for this reason

The performance of integrated transconductance amplifiers as variable current sources for bio-electric impedance measurements.

PubMed

Smith, D N

1992-01-01

Multiple applied current impedance measurement systems require numbers of current sources which operate simultaneously at the same frequency and within the same phase but at variable amplitudes. Investigations into the performance of some integrated operational transconductance amplifiers as variable current sources are described. Measurements of breakthrough, non-linearity and common-mode output levels for LM13600, NE5517 and CA3280 were carried out. The effects of such errors on the overall performance and stability of multiple current systems when driving floating loads are considered.

Operation ranges and dynamic capabilities of variable-speed pumped-storage hydropower

NASA Astrophysics Data System (ADS)

Mercier, Thomas; Olivier, Mathieu; Dejaeger, Emmanuel

2017-04-01

The development of renewable and intermittent power generation creates incentives for the development of both energy storage solutions and more flexible power generation assets. Pumped-storage hydropower (PSH) is the most established and mature energy storage technology, but recent developments in power electronics have created a renewed interest by providing PSH units with a variable-speed feature, thereby increasing their flexibility. This paper reviews technical considerations related to variable-speed PSH in link with the provision of primary frequency control, also referred to as frequency containment reserves (FCRs). Based on the detailed characteristics of a scale model pump-turbine, the variable-speed operation ranges in pump and turbine modes are precisely assessed and the implications for the provision of FCRs are highlighted. Modelling and control for power system studies are discussed, both for fixed- and variable-speed machines and simulation results are provided to illustrate the high dynamic capabilities of variable-speed PSH.

From ASCAT to Sentinel-1: Soil Moisture Monitoring using European C-Band Radars

NASA Astrophysics Data System (ADS)

Wagner, Wolfgang; Bauer-Marschallinger, Bernhard; Hochstöger, Simon

2016-04-01

The Advanced Scatterometer (ASCAT) is a C-Band radar instrument flown on board of the series of three METOP satellites. Albeit not operating in one of the more favorable longer wavelength ranges (S, L or P-band) as the dedicated Soil Moisture and Ocean Salinity (SMOS) and Soil Moisture Active Passive (SMAP) missions, it is one of main microwave sensors used for monitoring of soil moisture on a global scale. Its attractiveness for soil moisture monitoring applications stems from its operational status, high radiometric accuracy and stability, short revisit time, multiple viewing directions and long heritage (Wagner et al. 2013). From an application perspective, its main limitation is its spatial resolution of about 25 km, which does not allow resolving soil moisture patterns driven by smaller-scale hydrometeorological processes (e.g. convective precipitation, runoff patterns, etc.) that are themselves related to highly variable land surface characteristics (soil characteristics, topography, vegetation cover, etc.). Fortunately, the technique of aperture synthesis allows to significantly improve the spatial resolution of spaceborne radar instruments up to the meter scale. Yet, past Synthetic Aperture Radar (SAR) missions had not yet been designed to achieve a short revisit time required for soil moisture monitoring. This has only changed recently with the development and launch of SMAP (Entekhabi et al. 2010) and Sentinel-1 (Hornacek et al. 2012). Unfortunately, the SMAP radar failed only after a few months of operations, which leaves Sentinel-1 as the only currently operational SAR mission capable of delivering high-resolution radar observations with a revisit time of about three days for Europe, about weekly for most crop growing regions worldwide, and about bi-weekly to monthly over the rest of the land surface area. Like ASCAT, Sentinel-1 acquires C-band backscatter data in VV polarization over land. Therefore, for the interpretation of both ASCAT and Sentinel-1 backscatter observation, the same physical processes and geophysical variables (e.g. vegetation optical depth, surface roughness, soil volume scattering, etc.) need to be considered. The difference lies mainly in the scaling, i.e. how prominently the different variables influence the C-band data at the different spatial (25 km versus 20 m) and temporal (daily versus 3-30 days repeat coverage) scales. Therefore, while the general properties of soil moisture retrievals schemes used for ASCAT and Sentinel-1 can be the same, the details of the algorithm and parameterization will be different. This presentation will review similarities and differences of soil moisture retrieval approaches used for ASCAT and Sentinel-1, with a focus on the change detection method developed by TU Wien. Some first comparisons of ASCAT and Sentinel-1 soil moisture data over Europe will also be shown. REFERENCES Entekhabi, D., Njoku, E.G., O'Neill, P.E., Kellog, K.H., Crow, W.T., Edelstein, W.N., Entin, J.K., Goodman, S.D., Jackson, T.J., Johnson, J., Kimball, J., Piepmeier, J.R., Koster, R., Martin, N., McDonald, K.C., Moghaddam, M., Moran, S., Reichle, R., Shi, J.C., Spencer, M.W., Thurman, S.W., Tsang, L., & Van Zyl, J. (2010). The Soil Moisture Active Passive (SMAP) mission. Proceedings of the IEEE, 98, 704-716 Hornacek, M., Wagner, W., Sabel, D., Truong, H.L., Snoeij, P., Hahmann, T., Diedrich, E., & Doubkova, M. (2012). Potential for High Resolution Systematic Global Surface Soil Moisture Retrieval via Change Detection Using Sentinel-1. IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing, 5, 1303-1311 Wagner, W., Hahn, S., Kidd, R., Melzer, T., Bartalis, Z., Hasenauer, S., Figa-Saldana, J., De Rosnay, P., Jann, A., Schneider, S., Komma, J., Kubu, G., Brugger, K., Aubrecht, C., Züger, C., Gangkofer, U., Kienberger, S., Brocca, L., Wang, Y., Blöschl, G., Eitzinger, J., Steinnocher, K., Zeil, P., & Rubel, F. (2013). The ASCAT soil moisture product: A review of its specifications, validation results, and emerging applications. Meteorologische Zeitschrift, 22, 5-33

Numerical Ergonomics Analysis in Operation Environment of CNC Machine

NASA Astrophysics Data System (ADS)

Wong, S. F.; Yang, Z. X.

2010-05-01

The performance of operator will be affected by different operation environments [1]. Moreover, poor operation environment may cause health problems of the operator [2]. Physical and psychological considerations are two main factors that will affect the performance of operator under different conditions of operation environment. In this paper, applying scientific and systematic methods find out the pivot elements in the field of physical and psychological factors. There are five main factors including light, temperature, noise, air flow and space that are analyzed. A numerical ergonomics model has been built up regarding the analysis results which can support to advance the design of operation environment. Moreover, the output of numerical ergonomic model can provide the safe, comfortable, more productive conditions for the operator.

Biogenic carbon in combustible waste: waste composition, variability and measurement uncertainty.

PubMed

Larsen, Anna W; Fuglsang, Karsten; Pedersen, Niels H; Fellner, Johann; Rechberger, Helmut; Astrup, Thomas

2013-10-01

Obtaining accurate data for the contents of biogenic and fossil carbon in thermally-treated waste is essential for determination of the environmental profile of waste technologies. Relations between the variability of waste chemistry and the biogenic and fossil carbon emissions are not well described in the literature. This study addressed the variability of biogenic and fossil carbon in combustible waste received at a municipal solid waste incinerator. Two approaches were compared: (1) radiocarbon dating ((14)C analysis) of carbon dioxide sampled from the flue gas, and (2) mass and energy balance calculations using the balance method. The ability of the two approaches to accurately describe short-term day-to-day variations in carbon emissions, and to which extent these short-term variations could be explained by controlled changes in waste input composition, was evaluated. Finally, the measurement uncertainties related to the two approaches were determined. Two flue gas sampling campaigns at a full-scale waste incinerator were included: one during normal operation and one with controlled waste input. Estimation of carbon contents in the main waste types received was included. Both the (14)C method and the balance method represented promising methods able to provide good quality data for the ratio between biogenic and fossil carbon in waste. The relative uncertainty in the individual experiments was 7-10% (95% confidence interval) for the (14)C method and slightly lower for the balance method.

Optimization of mucilage extraction from chia seeds (Salvia hispanica L.) using response surface methodology.

PubMed

Orifici, Stefania C; Capitani, Marianela I; Tomás, Mabel C; Nolasco, Susana M

2018-02-25

Chia mucilage has potential application as a functional ingredient; advances on maximizing its extraction yield could represent a significant technological and economic impact for the food industry. Thus, first, the effect of mechanical agitation time (1-3 h) on the exudation of chia mucilage was analyzed. Then, response surface methodology was used to determine the optimal combination of the independent variables temperature (15-85 °C) and seed: water ratio (1: 12-1: 40.8 w/v) for the 2 h exudation that give maximum chia mucilage yield. Experiments were designed according to central composite rotatable design. A second-order polynomial model predicted the variation in extraction mucilage yield with the variables temperature and seed: water ratio. The optimal operating conditions were found to be temperature 85 °C and a seed: water ratio of 1: 31 (w/v), reaching an experimental extraction yield of 116 ± 0.21 g kg -1 (dry basis). The mucilage obtained exhibited good functional properties, mainly in terms of water-holding capacity, emulsifying activity, and emulsion stability. The results obtained show that temperature, seed: water ratio, and exudation time are important variables of the process that affect the extraction yield and the quality of the chia mucilage, determined according to its physicochemical and functional properties. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Validity of Monod kinetics at different sludge ages--peptone biodegradation under aerobic conditions.

PubMed

Orhon, Derin; Cokgor, Emine Ubay; Insel, Guclu; Karahan, Ozlem; Katipoglu, Tugce

2009-12-01

The study presented an evaluation of the effect of culture history (sludge age) on the growth kinetics of a mixed culture grown under aerobic conditions. It involved an experimental setup where a lab-scale sequencing batch reactor was operated at steady-state at two different sludge ages (theta(X)) of 2 and 10 days. The system sustained a mixed culture fed with a synthetic substrate mainly consisting of peptone. The initial concentration of substrate COD was selected around 500 mg COD/L. Polyhydroxyalkanoate (PHA) storage occurred to a limited extent, around 30 mg COD/L for theta(X)=10 days and 15 mg COD/L for theta(X)=2 days. Evaluation of the experimental data based on calibration of two different models provided consistent and reliable evidence for a variable Monod kinetics where the maximum specific growth rate, was assessed as 6.1/day for theta(X)=2 days and 4.1/day for theta(X)=10 days. A similar variability was also applicable for the hydrolysis and storage kinetics. The rate of storage was significantly lower than the levels reported in the literature, exhibiting the ability of the microorganisms to regulate their metabolic mechanisms for adjusting the rate of microbial growth and storage competing for the same substrate. This adjustment evidently resulted in case-specific, variable kinetics both for microbial growth and substrate storage.

Permanent split capacitor single phase electric motor system

DOEpatents

Kirschbaum, H.S.

1984-08-14

A permanent split capacitor single phase electric motor achieves balanced operation at more than one operating point by adjusting the voltage supplied to the main and auxiliary windings and adjusting the capacitance in the auxiliary winding circuit. An intermediate voltage tap on an autotransformer supplies voltage to the main winding for low speed operation while a capacitive voltage divider is used to adjust the voltage supplied to the auxiliary winding for low speed operation. 4 figs.

76 FR 6575 - Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-07

.... One operator reported a crack in a pre-modification main fitting. Shot peening was not present, as... received additional reports of cracked NLG main fittings. One operator reported a crack in a... optional closing action of EASA AD 2010-0001-E is embodiment of M-D B 146-32-150 (polishing and shot...

Expressions Module for the Satellite Orbit Analysis Program

NASA Technical Reports Server (NTRS)

Edmonds, Karina

2008-01-01

The Expressions Module is a software module that has been incorporated into the Satellite Orbit Analysis Program (SOAP). The module includes an expressions- parser submodule built on top of an analytical system, enabling the user to define logical and numerical variables and constants. The variables can capture output from SOAP orbital-prediction and geometric-engine computations. The module can combine variables and constants with built-in logical operators (such as Boolean AND, OR, and NOT), relational operators (such as >, <, or =), and mathematical operators (such as addition, subtraction, multiplication, division, modulus, exponentiation, differentiation, and integration). Parentheses can be used to specify precedence of operations. The module contains a library of mathematical functions and operations, including logarithms, trigonometric functions, Bessel functions, minimum/ maximum operations, and floating- point-to-integer conversions. The module supports combinations of time, distance, and angular units and has a dimensional- analysis component that checks for correct usage of units. A parser based on the Flex language and the Bison program looks for and indicates errors in syntax. SOAP expressions can be built using other expressions as arguments, thus enabling the user to build analytical trees. A graphical user interface facilitates use.

Western Wind and Solar Integration Study Phase 2 (Presentation)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lew, D.; Brinkman, G.; Ibanez, E.

This presentation accompanies Phase 2 of the Western Wind and Solar Integration Study, a follow-on to Phase 1, which examined the operational impacts of high penetrations of variable renewable generation on the electric power system in the West and was one of the largest variable generation studies to date. High penetrations of variable generation can induce cycling of fossil-fueled generators. Cycling leads to wear-and-tear costs and changes in emissions. Phase 2 calculated these costs and emissions, and simulated grid operations for a year to investigate the detailed impact of variable generation on the fossil-fueled fleet. The presentation highlights the scopemore » of the study and results.« less

Development and Testing of a Variable Conductance Thermal Acquisition, Transport, and Switching System

NASA Technical Reports Server (NTRS)

Bugby, David C.; Farmer, Jeffery T.; Stouffer, Charles J.

2013-01-01

This paper describes the development and testing of a scalable thermal management architecture for instruments, subsystems, or systems that must operate in severe space environments with wide variations in sink temperature. The architecture involves a serial linkage of one or more hot-side variable conductance heat pipes (VCHPs) to one or more cold-side loop heat pipes (LHPs). The VCHPs provide wide area heat acquisition, limited distance thermal transport, modest against gravity pumping, concentrated LHP startup heating, and high switching ratio variable conductance operation. The LHPs provide localized heat acquisition, long distance thermal transport, significant against gravity pumping, and high switching ratio variable conductance operation. The single-VCHP, single-LHP system described herein was developed to maintain thermal control of a small robotic lunar lander throughout the lunar day-night thermal cycle. It is also applicable to other variable heat rejection space missions in severe environments. Operationally, despite a 60-70% gas blocked VCHP condenser during ON testing, the system was still able to provide 2-4 W/K ON conductance, 0.01 W/K OFF conductance, and an end-to-end switching ratio of 200-400. The paper provides a detailed analysis of VCHP condenser performance, which quantified the gas blockage situation. Future multi-VCHP/multi-LHP thermal management system concepts that provide power/transport length scalability are also discussed.

What is the Effect of Interannual Hydroclimatic Variability on Water Supply Reservoir Operations?

NASA Astrophysics Data System (ADS)

Galelli, S.; Turner, S. W. D.

2015-12-01

Rather than deriving from a single distribution and uniform persistence structure, hydroclimatic data exhibit significant trends and shifts in their mean, variance, and lagged correlation through time. Consequentially, observed and reconstructed streamflow records are often characterized by features of interannual variability, including long-term persistence and prolonged droughts. This study examines the effect of these features on the operating performance of water supply reservoirs. We develop a Stochastic Dynamic Programming (SDP) model that can incorporate a regime-shifting climate variable. We then compare the performance of operating policies—designed with and without climate variable—to quantify the contribution of interannual variability to standard policy sub-optimality. The approach uses a discrete-time Markov chain to partition the reservoir inflow time series into small number of 'hidden' climate states. Each state defines a distinct set of inflow transition probability matrices, which are used by the SDP model to condition the release decisions on the reservoir storage, current-period inflow and hidden climate state. The experimental analysis is carried out on 99 hypothetical water supply reservoirs fed from pristine catchments in Australia—all impacted by the Millennium drought. Results show that interannual hydroclimatic variability is a major cause of sub-optimal hedging decisions. The practical import is that conventional optimization methods may misguide operators, particularly in regions susceptible to multi-year droughts.

A study of commuter airline economics

NASA Technical Reports Server (NTRS)

Summerfield, J. R.

1976-01-01

Variables are defined and cost relationships developed that describe the direct and indirect operating costs of commuter airlines. The study focused on costs for new aircraft and new aircraft technology when applied to the commuter airline industry. With proper judgement and selection of input variables, the operating costs model was shown to be capable of providing economic insight into other commuter airline system evaluations.

Redesign and Test of an SSME Turbopump for the Large Throat Main Combustion Chamber

NASA Technical Reports Server (NTRS)

Lunde, K. J.; Lee, G. A.; Eastland, A. H.; Rojas, L.

1994-01-01

The preburner oxidizer turbopump for the Space Shuttle Main Engine (SSME) was successfully redesigned for use with the Large Throat Main Combustion Chamber (LTMCC) and tested in air utilizing rapid prototyping. The redesign increases the SSME's operating range with the current Main Combustion Chamber (MCC) while achieving full operational range with the LTMCC. The use of rapid prototyping and air testing to validate the redesign demonstrated the ability to design, fabricate and test designs rapidly and at a very low cost.

Engine lubrication circuit including two pumps

DOEpatents

Lane, William H.

2006-10-03

A lubrication pump coupled to the engine is sized such that the it can supply the engine with a predetermined flow volume as soon as the engine reaches a peak torque engine speed. In engines that operate predominately at speeds above the peak torque engine speed, the lubrication pump is often producing lubrication fluid in excess of the predetermined flow volume that is bypassed back to a lubrication fluid source. This arguably results in wasted power. In order to more efficiently lubricate an engine, a lubrication circuit includes a lubrication pump and a variable delivery pump. The lubrication pump is operably coupled to the engine, and the variable delivery pump is in communication with a pump output controller that is operable to vary a lubrication fluid output from the variable delivery pump as a function of at least one of engine speed and lubrication flow volume or system pressure. Thus, the lubrication pump can be sized to produce the predetermined flow volume at a speed range at which the engine predominately operates while the variable delivery pump can supplement lubrication fluid delivery from the lubrication pump at engine speeds below the predominant engine speed range.

Variable recruitment fluidic artificial muscles: modeling and experiments

NASA Astrophysics Data System (ADS)

Bryant, Matthew; Meller, Michael A.; Garcia, Ephrahim

2014-07-01

We investigate taking advantage of the lightweight, compliant nature of fluidic artificial muscles to create variable recruitment actuators in the form of artificial muscle bundles. Several actuator elements at different diameter scales are packaged to act as a single actuator device. The actuator elements of the bundle can be connected to the fluidic control circuit so that different groups of actuator elements, much like individual muscle fibers, can be activated independently depending on the required force output and motion. This novel actuation concept allows us to save energy by effectively impedance matching the active size of the actuators on the fly based on the instantaneous required load. This design also allows a single bundled actuator to operate in substantially different force regimes, which could be valuable for robots that need to perform a wide variety of tasks and interact safely with humans. This paper proposes, models and analyzes the actuation efficiency of this actuator concept. The analysis shows that variable recruitment operation can create an actuator that reduces throttling valve losses to operate more efficiently over a broader range of its force-strain operating space. We also present preliminary results of the design, fabrication and experimental characterization of three such bioinspired variable recruitment actuator prototypes.

Theoretical and experimental researches on the operating costs of a wastewater treatment plant

NASA Astrophysics Data System (ADS)

Panaitescu, M.; Panaitescu, F.-V.; Anton, I.-A.

2015-11-01

Purpose of the work: The total cost of a sewage plants is often determined by the present value method. All of the annual operating costs for each process are converted to the value of today's correspondence and added to the costs of investment for each process, which leads to getting the current net value. The operating costs of the sewage plants are subdivided, in general, in the premises of the investment and operating costs. The latter can be stable (normal operation and maintenance, the establishment of power) or variables (chemical and power sludge treatment and disposal, of effluent charges). For the purpose of evaluating the preliminary costs so that an installation can choose between different alternatives in an incipient phase of a project, can be used cost functions. In this paper will be calculated the operational cost to make several scenarios in order to optimize its. Total operational cost (fixed and variable) is dependent global parameters of wastewater treatment plant. Research and methodology: The wastewater treatment plant costs are subdivided in investment and operating costs. We can use different cost functions to estimate fixed and variable operating costs. In this study we have used the statistical formulas for cost functions. The method which was applied to study the impact of the influent characteristics on the costs is economic analysis. Optimization of plant design consist in firstly, to assess the ability of the smallest design to treat the maximum loading rates to a given effluent quality and, secondly, to compare the cost of the two alternatives for average and maximum loading rates. Results: In this paper we obtained the statistical values for the investment cost functions, operational fixed costs and operational variable costs for wastewater treatment plant and its graphical representations. All costs were compared to the net values. Finally we observe that it is more economical to build a larger plant, especially if maximum loading rates are reached. The actual target of operational management is to directly implement the presented cost functions in a software tool, in which the design of a plant and the simulation of its behaviour are evaluated simultaneously.

Continuous-variable measurement-device-independent quantum key distribution with photon subtraction

NASA Astrophysics Data System (ADS)

Ma, Hong-Xin; Huang, Peng; Bai, Dong-Yun; Wang, Shi-Yu; Bao, Wan-Su; Zeng, Gui-Hua

2018-04-01

It has been found that non-Gaussian operations can be applied to increase and distill entanglement between Gaussian entangled states. We show the successful use of the non-Gaussian operation, in particular, photon subtraction operation, on the continuous-variable measurement-device-independent quantum key distribution (CV-MDI-QKD) protocol. The proposed method can be implemented based on existing technologies. Security analysis shows that the photon subtraction operation can remarkably increase the maximal transmission distance of the CV-MDI-QKD protocol, which precisely make up for the shortcoming of the original CV-MDI-QKD protocol, and one-photon subtraction operation has the best performance. Moreover, the proposed protocol provides a feasible method for the experimental implementation of the CV-MDI-QKD protocol.

Spatio-temporal activity of lightnings over Greece

NASA Astrophysics Data System (ADS)

Nastos, P. T.; Matsangouras, I. T.; Chronis, T. G.

2012-04-01

Extreme precipitation events are always associated with convective weather conditions driving to intense lightning activity: Cloud to Ground (CG), Ground to Cloud (GC) and Cloud to Cloud (CC). Thus, the study of lightnings, which typically occur during thunderstorms, gives evidence of the spatio-temporal variability of intense precipitation. Lightning is a natural phenomenon in the atmosphere, being a major cause of storm related with deaths and main trigger of forest fires during dry season. Lightning affects the many electrochemical systems of the body causing nerve damage, memory loss, personality change, and emotional problems. Besides, among the various nitrogen oxides sources, the contribution from lightning likely represents the largest uncertainty. An operational lightning detection network (LDN) has been established since 2007 by HNMS, consisting of eight time-of-arrival sensors (TOA), spatially distributed across Greek territory. In this study, the spatial and temporal variability of recorded lightnings (CG, GC and CC) are analyzed over Greece, during the period from January 14, 2008 to December 31, 2009, for the first time. The data for retrieving the location and time-of-occurrence of lightning were acquired from Hellenic National Meteorological Service (HNMS). In addition to the analysis of spatio-temporal activity over Greece, the HNMS-LDN characteristics are also presented. The results of the performed analysis reveal the specific geographical sub-regions associated with lightnings incidence. Lightning activity occurs mainly during the autumn season, followed by summer and spring. Higher frequencies of flashes appear over Ionian and Aegean Sea than over land during winter period against continental mountainous regions during summer period.

Measurement variability error for estimates of volume change

Treesearch

James A. Westfall; Paul L. Patterson

2007-01-01

Using quality assurance data, measurement variability distributions were developed for attributes that affect tree volume prediction. Random deviations from the measurement variability distributions were applied to 19381 remeasured sample trees in Maine. The additional error due to measurement variation and measurement bias was estimated via a simulation study for...

Vehicle operating costs, fuel consumption, and pavement type condition factors

DOT National Transportation Integrated Search

1982-06-01

This report presents updated vehicle operating cost tables which may be used by a highway agency for estimation of vehicle operating costs as a function of operational and roadway variables. These results, partially based on fuel consumption tests on...

A Study of Interpersonal Conflict Among Operating Room Nurses.

PubMed

Chang, Tsui-Fen; Chen, Chung-Kuang; Chen, Ming-Jia

2017-12-01

Team collaboration is an important factor that affects the performance of the operating room (OR). Therefore, the ability of OR nurses to adapt to and manage interpersonal conflict incidents properly is very important. The aims of this study were to investigate the interpersonal conflict management capabilities of OR nursing staffs and to find the relationships among the demographics of OR nurses and the following: work-related variables, interpersonal conflict management style, and target of interpersonal conflict. This study investigated 201 OR nurses who had worked for more than 6 months at the target hospitals, which were located in the three counties of Changhua, Yunlin, and Chiayi. The questionnaire that was used to collect data included three components: a demographic and work-related variables survey, interpersonal conflict management factor analysis scale, and interpersonal conflict parties and frequency scale. Data were analyzed using independent t test, analysis of variance, Scheffe's test, and Pearson's correlation coefficient. The main findings were as follows: (a) Integration and arbitration were the major interpersonal conflict management strategies adopted by the participants; (b) medical doctor, OR nurses, and anesthetists were the primary targets of conflict for the participants; (c) the factors of educational background, job position, experience in other departments, seniority, attending courses in conflict management, and level of hospital significantly affected the strategies that participants used to manage interpersonal conflict; and (d) license level, experience in other departments, seniority, and inclination toward serving in the OR were each found to relate significantly to the target of interpersonal conflict and the frequency of interpersonal conflict incidents. The main implications of this study are as follows: (a) The environment for communication in the OR should be made more friendly to encourage junior OR nurses to adopt constructive interpersonal conflict management strategies; (b) prior experience in other departments should be one of the most important factors of consideration when recruiting new nurses for the OR; and (c) hospitals should provide more interpersonal conflict management training courses to support the capability of OR nursing staffs in terms of adopting cooperativeness strategies and coping effectively with all types of interpersonal conflicts.

Cooperative Coevolution with Formula-Based Variable Grouping for Large-Scale Global Optimization.

PubMed

Wang, Yuping; Liu, Haiyan; Wei, Fei; Zong, Tingting; Li, Xiaodong

2017-08-09

For a large-scale global optimization (LSGO) problem, divide-and-conquer is usually considered an effective strategy to decompose the problem into smaller subproblems, each of which can then be solved individually. Among these decomposition methods, variable grouping is shown to be promising in recent years. Existing variable grouping methods usually assume the problem to be black-box (i.e., assuming that an analytical model of the objective function is unknown), and they attempt to learn appropriate variable grouping that would allow for a better decomposition of the problem. In such cases, these variable grouping methods do not make a direct use of the formula of the objective function. However, it can be argued that many real-world problems are white-box problems, that is, the formulas of objective functions are often known a priori. These formulas of the objective functions provide rich information which can then be used to design an effective variable group method. In this article, a formula-based grouping strategy (FBG) for white-box problems is first proposed. It groups variables directly via the formula of an objective function which usually consists of a finite number of operations (i.e., four arithmetic operations "[Formula: see text]", "[Formula: see text]", "[Formula: see text]", "[Formula: see text]" and composite operations of basic elementary functions). In FBG, the operations are classified into two classes: one resulting in nonseparable variables, and the other resulting in separable variables. In FBG, variables can be automatically grouped into a suitable number of non-interacting subcomponents, with variables in each subcomponent being interdependent. FBG can easily be applied to any white-box problem and can be integrated into a cooperative coevolution framework. Based on FBG, a novel cooperative coevolution algorithm with formula-based variable grouping (so-called CCF) is proposed in this article for decomposing a large-scale white-box problem into several smaller subproblems and optimizing them respectively. To further enhance the efficiency of CCF, a new local search scheme is designed to improve the solution quality. To verify the efficiency of CCF, experiments are conducted on the standard LSGO benchmark suites of CEC'2008, CEC'2010, CEC'2013, and a real-world problem. Our results suggest that the performance of CCF is very competitive when compared with those of the state-of-the-art LSGO algorithms.

[Blood pressure variability: clinical interest or simple curiosity?].

PubMed

Ciaroni, Stefano

2007-03-14

Blood pressure variability is a physiological phenomenon influenced by many internal and external factors. This variability could be also influenced by pathological conditions such as arterial hypertension. Two forms must be mainly distinguished: the blood pressure variability at long and short-term. The latter could only be studied by continuous recordings. In this article will be analysed the interest of measuring blood pressure variability, its cardiovascular prognosis and the therapeutic tools when it is increased.

System properties, feedback control and effector coordination of human temperature regulation.

PubMed

Werner, Jürgen

2010-05-01

The aim of human temperature regulation is to protect body processes by establishing a relative constancy of deep body temperature (regulated variable), in spite of external and internal influences on it. This is basically achieved by a distributed multi-sensor, multi-processor, multi-effector proportional feedback control system. The paper explains why proportional control implies inherent deviations of the regulated variable from the value in the thermoneutral zone. The concept of feedback of the thermal state of the body, conveniently represented by a high-weighted core temperature (T (c)) and low-weighted peripheral temperatures (T (s)) is equivalent to the control concept of "auxiliary feedback control", using a main (regulated) variable (T (c)), supported by an auxiliary variable (T (s)). This concept implies neither regulation of T (s) nor feedforward control. Steady-states result in the closed control-loop, when the open-loop properties of the (heat transfer) process are compatible with those of the thermoregulatory processors. They are called operating points or balance points and are achieved due to the inherent property of dynamical stability of the thermoregulatory feedback loop. No set-point and no comparison of signals (e.g. actual-set value) are necessary. Metabolic heat production and sweat production, though receiving the same information about the thermal state of the body, are independent effectors with different thresholds and gains. Coordination between one of these effectors and the vasomotor effector is achieved by the fact that changes in the (heat transfer) process evoked by vasomotor control are taken into account by the metabolic/sweat processor.

VASP- VARIABLE DIMENSION AUTOMATIC SYNTHESIS PROGRAM

NASA Technical Reports Server (NTRS)

White, J. S.

1994-01-01

VASP is a variable dimension Fortran version of the Automatic Synthesis Program, ASP. The program is used to implement Kalman filtering and control theory. Basically, it consists of 31 subprograms for solving most modern control problems in linear, time-variant (or time-invariant) control systems. These subprograms include operations of matrix algebra, computation of the exponential of a matrix and its convolution integral, and the solution of the matrix Riccati equation. The user calls these subprograms by means of a FORTRAN main program, and so can easily obtain solutions to most general problems of extremization of a quadratic functional of the state of the linear dynamical system. Particularly, these problems include the synthesis of the Kalman filter gains and the optimal feedback gains for minimization of a quadratic performance index. VASP, as an outgrowth of the Automatic Synthesis Program, has the following improvements: more versatile programming language; more convenient input/output format; some new subprograms which consolidate certain groups of statements that are often repeated; and variable dimensioning. The pertinent difference between the two programs is that VASP has variable dimensioning and more efficient storage. The documentation for the VASP program contains a VASP dictionary and example problems. The dictionary contains a description of each subroutine and instructions on its use. The example problems include dynamic response, optimal control gain, solution of the sampled data matrix Riccati equation, matrix decomposition, and a pseudo-inverse of a matrix. This program is written in FORTRAN IV and has been implemented on the IBM 360. The VASP program was developed in 1971.

Parareal algorithms with local time-integrators for time fractional differential equations

NASA Astrophysics Data System (ADS)

Wu, Shu-Lin; Zhou, Tao

2018-04-01

It is challenge work to design parareal algorithms for time-fractional differential equations due to the historical effect of the fractional operator. A direct extension of the classical parareal method to such equations will lead to unbalance computational time in each process. In this work, we present an efficient parareal iteration scheme to overcome this issue, by adopting two recently developed local time-integrators for time fractional operators. In both approaches, one introduces auxiliary variables to localized the fractional operator. To this end, we propose a new strategy to perform the coarse grid correction so that the auxiliary variables and the solution variable are corrected separately in a mixed pattern. It is shown that the proposed parareal algorithm admits robust rate of convergence. Numerical examples are presented to support our conclusions.

Long-term dynamics of a floodplain shallow lake in the Pantanal wetland: Is it all about climate?

PubMed

Silio-Calzada, Ana; Barquín, José; Huszar, Vera L M; Mazzeo, Nestor; Méndez, Fernando; Álvarez-Martínez, Jose Manuel

2017-12-15

Hydrological variability over seasonal and multi-annual timescales strongly shapes the ecological structure and functioning of floodplain ecosystems. The current IPCC climate scenario foresees an increase in the frequency of extreme events. This, in conjunction with other anthropogenic disturbances (e.g., river regulation or land-use changes) poses a serious threat to the natural functioning of these ecosystems. In this study we aimed to i) evaluate the long-term variability of the flooded area of the third largest floodplain lake in the Brazilian Pantanal using remote sensing techniques, and ii) analyze the possible factors influencing this variability. Changes in open-water and riparian floodplain-wetland vegetation areas were mapped by applying an ad hoc-developed remote-sensing method (including a newly developed normalized water index, NWI) to 221 Landsat-Thematic Mapper (TM)/Enhanced Thematic Mapper Plus (ETM+) images, acquired between 1984 and 2011. Added to the lake's natural swing between riparian floodplain-wetland vegetation expansion and retraction, our analyses revealed large interannual changes, grouped into three main periods within the studied time interval. Moreover, our results indicate that this floodplain-lake system is losing open-water area, paired with an increase in riparian floodplain-wetland vegetation. The system's long-term dynamics are not all climate related, but are the result of a combination of drivers. The start of the Manso dam's operation upstream of the studied system, and the subsequent river regulation because of the dam operation, coupled with climatic oscillation appear to be responsible for the observed changes. However, other factors which were not considered in this study might also be important in this process and contributing to the reduction of the system's resilience to droughts (e.g., land-use changes). This study illustrates the serious conservation risks that the Pantanal faces in the near future, given the current climate-change scenario and the accumulation of dam building projects in this region. Copyright © 2017 Elsevier B.V. All rights reserved.

Risk factors for computer visual syndrome (CVS) among operators of two call centers in São Paulo, Brazil.

PubMed

Sa, Eduardo Costa; Ferreira Junior, Mario; Rocha, Lys Esther

2012-01-01

The aims of this study were to investigate work conditions, to estimate the prevalence and to describe risk factors associated with Computer Vision Syndrome among two call centers' operators in São Paulo (n = 476). The methods include a quantitative cross-sectional observational study and an ergonomic work analysis, using work observation, interviews and questionnaires. The case definition was the presence of one or more specific ocular symptoms answered as always, often or sometimes. The multiple logistic regression model, were created using the stepwise forward likelihood method and remained the variables with levels below 5% (p < 0.05). The operators were mainly female and young (from 15 to 24 years old). The call center was opened 24 hours and the operators weekly hours were 36 hours with break time from 21 to 35 minutes per day. The symptoms reported were eye fatigue (73.9%), "weight" in the eyes (68.2%), "burning" eyes (54.6%), tearing (43.9%) and weakening of vision (43.5%). The prevalence of Computer Vision Syndrome was 54.6%. Associations verified were: being female (OR 2.6, 95% CI 1.6 to 4.1), lack of recognition at work (OR 1.4, 95% CI 1.1 to 1.8), organization of work in call center (OR 1.4, 95% CI 1.1 to 1.7) and high demand at work (OR 1.1, 95% CI 1.0 to 1.3). The organization and psychosocial factors at work should be included in prevention programs of visual syndrome among call centers' operators.

Managing Sustainable Demand-side Infrastructure for Power System Ancillary Services

NASA Astrophysics Data System (ADS)

Parkinson, Simon Christopher

Widespread access to renewable electricity is seen as a viable method to mitigate carbon emissions, although problematic are the issues associated with the integration of the generation systems within current power system configurations. Wind power plants are the primary large-scale renewable generation technology applied globally, but display considerable short-term supply variability that is difficult to predict. Power systems are currently not designed to operate under these conditions, and results in the need to increase operating reserve in order to guarantee stability. Often, operating conventional generation as reserve is both technically and economically inefficient, which can overshadow positive benefits associated with renewable energy exploitation. The purpose of this thesis is to introduce and assess an alternative method of enhancing power system operations through the control of electric loads. In particular, this thesis focuses on managing highly-distributed sustainable demand-side infrastructure, in the form of heat pumps, electric vehicles, and electrolyzers, as dispatchable short-term energy balancing resources. The main contribution of the thesis is an optimal control strategy capable of simultaneously balancing grid- and demand-side objectives. The viability of the load control strategy is assessed through model-based simulations that explicitly track end-use functionality of responsive devices within a power systems analysis typically implemented to observe the effects of integrated wind energy systems. Results indicate that there is great potential for the proposed method to displace the need for increased reserve capacity in systems considering a high penetration of wind energy, thereby allowing conventional generation to operate more efficiently and avoid the need for possible capacity expansions.

Effect of tranexamic acid administration on bleeding in primary total hip arthroplasty.

PubMed

Fernández-Cortiñas, A B; Quintáns-Vázquez, J M; Gómez-Suárez, F; Murillo, O Simón; Sánchez-López, B R; Pena-Gracía, J M

To study the efficacy of tranexamic acid to decrease perioperative bleeding in patients who have undergone a total hip arthroplasty operation and to evaluate drug safety. Observational, prospective, controlled and randomized study on the efficacy of tranexamic acid as a method to reduce bleeding in primary hip replacement surgery. We included 134 patients operated during 2014 in our centre, who were divided into 2 groups according to whether or not they had received tranexamic acid. The main study variables were haemoglobin and haematocrit levels, the amount of blood collected from the post-operative drain in the first 12, 24 and 48hours and transfusion requirements. Post-operative haemoglobin and haematocrit levels were statistically higher (P<.001) in the group with treatment. During the first 48hours bleeding values from the group that did not receive TAX were higher compared to patients treated with tranexamic acid. Statistically significant differences (P=.001) were found as to the need for transfusion according to group, more transfusions were performed in the cohort that had not received tranexamic acid: 25.37% compared to 4.48% for the group with tranexamic acid. No adverse events related to administration of tranexamic acid were recorded. Administration of tranexamic acid has proved to be an effective and safe method to reduce peri-operative bleeding in patients who underwent total hip arthroplasty and avoids allogenic blood transfusion. Therefore, tranexamic acid treatment could entail a financial saving for the healthcare system and expose the patient to less risk. Copyright © 2017 SECOT. Publicado por Elsevier España, S.L.U. All rights reserved.

Two-D results on human operator perception

NASA Technical Reports Server (NTRS)

Siapkara, A. A.; Sheridan, T. B.

1981-01-01

The application of multidimensional scaling methodology in human factors engineering is presented. The nonorthogonality of internally perceived task variables is exhibited for first and second order plants with both dependent and independent task variables. Directions of operator preference are shown for actual performance, pilot opinion rating, and subjective measures of fatigue, adaptability, and system recognition. Improvement of performance in second order systems is exhibited by the use of bang-bang feedback information. Dissimilarity measures for system comparison are suggested in order to account for human operator rotations and subjective sense of time.

Laparoscopic Partial Nephrectomy with Diode Laser: A Promising Technique

PubMed Central

Knezevic, Nikola; Maric, Marjan; Grkovic, Marija Topalovic; Krhen, Ivan; Kastelan, Zeljko

2014-01-01

Abstract Objective: The aim of this study was to evaluate application of diode laser in laparoscopic partial nephrectomy (LPN), and to question this technique in terms of ease of tumor excision and reduction of warm ischemia time (WIT). Background data: LPN is the standard operative method for small renal masses. The benefits of LPN are numerous, including preserving renal function and prolonging overall survival. However, reduction of WIT remains main challenge in this operation. In order to shorten WIT, many techniques have been developed, with variable results. Patients and methods: We performed a prospective collection and analysis of health records for patients who were operated on between March 2011 and August 2012. Inclusion criteria were single tumor ≤4 cm, predominant exophytic growth and intraparenchymal depth ≤1.5 cm, with a minimum distance of 5 mm from the urinary collecting system. Results: We operated on 17 patients. Median operative time was 170 min. In all but two patients, we had to perform hilar clamping. Median duration of WIT was 16 min. Pathohistological evaluation revealed clear cell renal cancer and confirmed margins negative for tumor in all cases. Median size of the tumor was 3 cm. Median postoperative hospitalization was 5 days. Average follow up was 11.5 months. There were no intraoperative complications. One postoperative complication was noted: perirenal hematoma. Conclusions: Laser LPN is feasible, and offers the benefit of shorter WIT, with effective tissue coagulation and hemostasis. With operative experience and technical advances, WIT will be reduced or even eliminated, and a solution to some technical difficulties, such as significant smoke production, will be found. PMID:24460067

Surgical site infections following craniotomy focusing on possible post-operative acquisition of infection: prospective cohort study.

PubMed

Sneh-Arbib, O; Shiferstein, A; Dagan, N; Fein, S; Telem, L; Muchtar, E; Eliakim-Raz, N; Rubinovitch, B; Rubin, G; Rappaport, Z H; Paul, M

2013-12-01

Neurosurgery is characterized by a prolonged risk period for surgical site infection (SSI), mainly related to the presence of cerebrospinal fluid (CSF) drains. We aimed to examine factors associated with post-neurosurgical SSIs, focusing on post-operative factors. A prospective cohort study was conducted in a single center over a period of 18 months in Israel. Included were adult patients undergoing clean or clean-contaminated craniotomy, including craniotomies with external CSF drainage or shunts. SSIs were defined by the Centers for Disease Control and Prevention (CDC) criteria for healthcare-associated infections. All patients were followed up for 90 days and those with foreign body insertion for 1 year. We compared patients with and without SSI. A multivariable regression analysis for SSI was conducted including uncorrelated variables significantly associated with SSI. A total of 502 patients were included, with 138 (27.5%) undergoing emergent or urgent craniotomy. The overall SSI rate was 5.6% (28 patients), of which 3.2% (16 patients) were intracerebral. Non-elective surgery, external CSF drainage/monitoring devices, re-operation, and post-operative respiratory failure were independently associated with subsequent SSI. External CSF devices was the only significant risk factor for intracerebral SSIs (p < 0.001). Internal shunts or other foreign body insertions were not associated with SSIs. A phenotypically identical isolate to that causing the SSI was isolated from respiratory secretions prior to the SSI in 4/9 patients with microbiologically documented intracerebral SSIs. Patients with SSIs had longer hospital stay, poorer functional capacity on discharge, and higher 90-day mortality. We raise the possibility of post-operative infection acquisition through external CSF devices. Standard operating procedures for their maintenance are necessary.

Age and sex of surgeons and mortality of older surgical patients: observational study

PubMed Central

Jena, Anupam B; Orav, E John; Blumenthal, Daniel M; Tsai, Thomas C; Mehtsun, Winta T; Jha, Ashish K

2018-01-01

Abstract Objective To investigate whether patients’ mortality differs according to the age and sex of surgeons. Design Observational study. Setting US acute care hospitals. Participants 100% of Medicare fee-for-service beneficiaries aged 65-99 years who underwent one of 20 major non-elective surgeries between 2011 and 2014. Main outcome measure Operative mortality rate of patients, defined as death during hospital admission or within 30 days of the operative procedure, after adjustment for patients’ and surgeons’ characteristics and indicator variables for hospitals. Results 892 187 patients who were treated by 45 826 surgeons were included. Patients’ mortality was lower for older surgeons than for younger surgeons: the adjusted operative mortality rates were 6.6% (95% confidence interval 6.5% to 6.7%), 6.5% (6.4% to 6.6%), 6.4% (6.3% to 6.5%), and 6.3% (6.2% to 6.5%) for surgeons aged under 40 years, 40-49 years, 50-59 years, and 60 years or over, respectively (P for trend=0.001). There was no evidence that adjusted operative mortality differed between patients treated by female versus male surgeons (adjusted mortality 6.3% for female surgeons versus 6.5% for male surgeons; adjusted odds ratio 0.97, 95% confidence interval 0.93 to 1.01). After stratification by sex of surgeon, patients’ mortality declined with age of surgeon for both male and female surgeons (except for female surgeons aged 60 or older); female surgeons in their 50s had the lowest operative mortality. Conclusion Using national data on Medicare beneficiaries in the US, this study found that patients treated by older surgeons had lower mortality than patients treated by younger surgeons. There was no evidence that operative mortality differed between male and female surgeons. PMID:29695473

Schedule-Induced and Operant Mechanisms that Influence Response Variability: A Review and Implications for Future Investigations

ERIC Educational Resources Information Center

Lee, Ronald; Sturmey, Peter; Fields, Lanny

2007-01-01

Response variability, a fundamental characteristic of behavior, may be in some cases an induced effect of reinforcement schedules. Research on schedule-induced response variability has shown that continuous reinforcement results in less variability than intermittent reinforcement schedules. Studies on the effects of intermittency of reinforcement,…

PHARAO laser source flight model: Design and performances

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lévèque, T., E-mail: thomas.leveque@cnes.fr; Faure, B.; Esnault, F. X.

2015-03-15

In this paper, we describe the design and the main performances of the PHARAO laser source flight model. PHARAO is a laser cooled cesium clock specially designed for operation in space and the laser source is one of the main sub-systems. The flight model presented in this work is the first remote-controlled laser system designed for spaceborne cold atom manipulation. The main challenges arise from mechanical compatibility with space constraints, which impose a high level of compactness, a low electric power consumption, a wide range of operating temperature, and a vacuum environment. We describe the main functions of the lasermore » source and give an overview of the main technologies developed for this instrument. We present some results of the qualification process. The characteristics of the laser source flight model, and their impact on the clock performances, have been verified in operational conditions.« less

Economic optimization of operations for hybrid energy systems under variable markets

DOE PAGES

Chen, Jen; Garcia, Humberto E.

2016-05-21

We prosed a hybrid energy systems (HES) which is an important element to enable increasing penetration of clean energy. Our paper investigates the operations flexibility of HES, and develops a methodology for operations optimization for maximizing economic value based on predicted renewable generation and market information. A multi-environment computational platform for performing such operations optimization is also developed. In order to compensate for prediction error, a control strategy is accordingly designed to operate a standby energy storage element (ESE) to avoid energy imbalance within HES. The proposed operations optimizer allows systematic control of energy conversion for maximal economic value. Simulationmore » results of two specific HES configurations are included to illustrate the proposed methodology and computational capability. These results demonstrate the economic viability of HES under proposed operations optimizer, suggesting the diversion of energy for alternative energy output while participating in the ancillary service market. Economic advantages of such operations optimizer and associated flexible operations are illustrated by comparing the economic performance of flexible operations against that of constant operations. Sensitivity analysis with respect to market variability and prediction error, are also performed.« less