Experimental demonstration of polarization encoding quantum key distribution system based on intrinsically stable polarization-modulated units.

PubMed

Wang, Jindong; Qin, Xiaojuan; Jiang, Yinzhu; Wang, Xiaojing; Chen, Liwei; Zhao, Feng; Wei, Zhengjun; Zhang, Zhiming

2016-04-18

A proof-of-principle demonstration of a one-way polarization encoding quantum key distribution (QKD) system is demonstrated. This approach can automatically compensate for birefringence and phase drift. This is achieved by constructing intrinsically stable polarization-modulated units (PMUs) to perform the encoding and decoding, which can be used with four-state protocol, six-state protocol, and the measurement-device-independent (MDI) scheme. A polarization extinction ratio of about 30 dB was maintained for several hours over a 50 km optical fiber without any adjustments to our setup, which evidences its potential for use in practical applications.

Inequalities in maintenance of health and performance between young adult women and men in higher education.

PubMed

Löve, Jesper; Dellve, Lotta; Eklöf, Mats; Hagberg, Mats

2009-04-01

Because of ageing populations, most high-income countries are facing an imminent scarcity of labour. Maintenance of health and performance in young adults therefore becomes a crucial prerequisite for sustainable societies. One major obstruction to this accomplishment is the striking health inequalities between young women and young men. Previously these inequalities have mainly been studied in a cross-sectional way, focusing on ill-health. In this study, we compared the prevalence of maintained health and performance between young adult women and men and the predictors for this outcome. The cohort consisted of 1266 participants from a homogenous sample of university students in Sweden. A combined assessment of self-rated 'very good' health and un-impaired performance took place at three time points (i.e. maintained health and performance). Potential predictors covered stable conditions in health-related behaviours, conditions at work/school and work-home interference. Young women had less maintained health and performance than young men. No major differences in predictors were found. However, there was a tendency for psychosocial factors to be the most important predictors, especially in women. That young women had less maintained health and performance in a homogenous sample beyond well-known differentiating factors suggests explanations other than observable structural differences between the sexes. This was also indicated by the importance attached to perceived demands, and work-home interference, especially in women. The combination of less scheduled, and more unscheduled, schoolwork (i.e. time-flexibility) negatively affected the maintenance of health and performance in our study population, suggesting a focus for future studies.

Chip Scale Ultra-Stable Clocks: Miniaturized Phonon Trap Timing Units for PNT of CubeSats

NASA Technical Reports Server (NTRS)

Rais-Zadeh, Mina; Altunc, Serhat; Hunter, Roger C.; Petro, Andrew

2016-01-01

The Chip Scale Ultra-Stable Clocks (CSUSC) project aims to provide a superior alternative to current solutions for low size, weight, and power timing devices. Currently available quartz-based clocks have problems adjusting to the high temperature and extreme acceleration found in space applications, especially when scaled down to match small spacecraft size, weight, and power requirements. The CSUSC project aims to utilize dual-mode resonators on an ovenized platform to achieve the exceptional temperature stability required for these systems. The dual-mode architecture utilizes a temperature sensitive and temperature stable mode simultaneously driven on the same device volume to eliminate ovenization error while maintaining extremely high performance. Using this technology it is possible to achieve parts-per-billion (ppb) levels of temperature stability with multiple orders of magnitude smaller size, weight, and power.

Bi-stable optical actuator

DOEpatents

Holdener, Fred R.; Boyd, Robert D.

2000-01-01

The present invention is a bi-stable optical actuator device that is depowered in both stable positions. A bearing is used to transfer motion and smoothly transition from one state to another. The optical actuator device may be maintained in a stable position either by gravity or a restraining device.

Historical overfishing and the recent collapse of coastal ecosystems

USGS Publications Warehouse

Jackson, J.B.C.; Kirby, M.X.; Berger, W.H.; Bjorndal, K.A.; Botsford, L.W.; Bourque, B.J.; Bradbury, R.; Cooke, R.; Erlandson, J.; Estes, J.A.; Hughes, T.P.; Kidwell, S.; Lange, C.B.; Lenihan, H.S.; Pandolfi, J.M.; Peterson, C.H.; Steneck, R.S.; Tegner, M.J.; Warner, R.

2001-01-01

A method for calculating parameters necessary to maintain stable populations is described and the management implications of the method are discussed. This method depends upon knowledge of the population mortality rate schedule, the age at which the species reaches maturity, and recruitment rates or age ratios in the population. Four approaches are presented which yield information about the status of the population: (1) necessary production for a stable population, (2) allowable mortality for a stable population, (3) annual rate of change in population size, and (4) age ratios in the population which yield a stable condition. General formulas for these relationships, and formulas for several special cases, are presented. Tables are also presented showing production required to maintain a stable population with the simpler (more common) mortality and fecundity schedules.

Transient analysis of gas transport in anode channel of a polymer electrolyte membrane fuel cell with dead-ended anode under pressure swing operation

NASA Astrophysics Data System (ADS)

Ichikawa, Yasushi; Oshima, Nobuyuki; Tabuchi, Yuichiro; Ikezoe, Keigo

2014-12-01

Further cost reduction is a critical issue for commercialization of fuel-cell electric vehicles (FCEVs) based on polymer electrolyte fuel cells (PEFCs). The cost of the fuel-cell system is driven by the multiple parts required to maximize stack performance and maintain durability and robustness. The fuel-cell system of the FCEV must be simplified while maintaining functionality. The dead-ended anode is considered as a means of simplification in this study. Generally, if hydrogen is supplied under constant pressure during dead-ended operation, stable power generation is impossible because of accumulation of liquid water produced by power generation and of nitrogen via leakage from the cathode through the membrane. Herein, pressure oscillation is applied to address this issue. Empirical and CFD data are employed to elucidate the mechanism of stable power generation using the pressure swing supply. Simultaneous and time-continuous measurements of the current distribution and gas concentration distribution are also conducted. The results demonstrate that the nitrogen concentration in the anode channel under pressure constant operation differs from that under pressure swing supply conditions. The transient two-dimensional CFD results indicate that oscillatory flow is generated by pressure swing supply, which periodically sweeps out nitrogen from the active area, resulting in stable power generation.

Highly stable, extremely high-temperature, nonvolatile memory based on resistance switching in polycrystalline Pt nanogaps

PubMed Central

Suga, Hiroshi; Suzuki, Hiroya; Shinomura, Yuma; Kashiwabara, Shota; Tsukagoshi, Kazuhito; Shimizu, Tetsuo; Naitoh, Yasuhisa

2016-01-01

Highly stable, nonvolatile, high-temperature memory based on resistance switching was realized using a polycrystalline platinum (Pt) nanogap. The operating temperature of the memory can be drastically increased by the presence of a sharp-edged Pt crystal facet in the nanogap. A short distance between the facet edges maintains the nanogap shape at high temperature, and the sharp shape of the nanogap densifies the electric field to maintain a stable current flow due to field migration. Even at 873 K, which is a significantly higher temperature than feasible for conventional semiconductor memory, the nonvolatility of the proposed memory allows stable ON and OFF currents, with fluctuations of less than or equal to 10%, to be maintained for longer than eight hours. An advantage of this nanogap scheme for high-temperature memory is its secure operation achieved through the assembly and disassembly of a Pt needle in a high electric field. PMID:27725705

Surface/interface effects on high-performance thin-film all-solid-state Li-ion batteries

DOE PAGES

Gong, Chen; Ruzmetov, Dmitry; Pearse, Alexander; ...

2015-10-05

The further development of all-solid-state batteries is still limited by the understanding/engineering of the interfaces formed upon cycling. Here, we correlate the morphological, chemical, and electrical changes of the surface of thin-film devices with Al negative electrodes. The stable Al–Li–O alloy formed at the stress-free surface of the electrode causes rapid capacity fade, from 48.0 to 41.5 μAh/cm 2 in two cycles. Surprisingly, the addition of a Cu capping layer is insufficient to prevent the device degradation. Furthermore, Si electrodes present extremely stable cycling, maintaining >92% of its capacity after 100 cycles, with average Coulombic efficiency of 98%.

Psychophysiological Tracking of a Female Physique Competitor through Competition Preparation

PubMed Central

ROHRIG, BRANDON J.; PETTITT, ROBERT W.; PETTITT, CHERIE D.; KANZENBACH, TODD L.

2017-01-01

Natural physique competitions are based on subjective judgments of how a competitor appears on show day. Prior to competition, there is a prolonged dieting phase referred to as contest preparation. The primary goal is to reduce body fat levels while maintaining skeletal muscle mass. The study tracked the physiological and psychological changes for a 24 year old female preparing for a physique competition. Purpose: The study was conducted to describe the physiological and psychological changes of a female physique competitor who engages in long-term contest preparation. Methods: Diet, body composition, blood work, energy expenditure, mood, and performance were evaluated through contest preparation. Results: The participant lost 10.1kg throughout contest preparation in a strong weekly linear pattern (R2=0.97). Body fat was reduced from 30.45% to 15.85% while fat free mass was maintained. Mood for the participant remained stable until month five, when an observed variation occurred, with performance maintaining. Conclusions: Contest preparation was successful in reducing the body fat in the participant while having a minimum effect on both performance and fat free mass. For athletes looking to lose large amounts of body fat with minimal performance decrements a prolonged diet period with moderate exercise and food restriction can be an effective solution. PMID:28344742

Psychophysiological Tracking of a Female Physique Competitor through Competition Preparation.

PubMed

Rohrig, Brandon J; Pettitt, Robert W; Pettitt, Cherie D; Kanzenbach, Todd L

2017-01-01

Natural physique competitions are based on subjective judgments of how a competitor appears on show day. Prior to competition, there is a prolonged dieting phase referred to as contest preparation. The primary goal is to reduce body fat levels while maintaining skeletal muscle mass. The study tracked the physiological and psychological changes for a 24 year old female preparing for a physique competition. The study was conducted to describe the physiological and psychological changes of a female physique competitor who engages in long-term contest preparation. Diet, body composition, blood work, energy expenditure, mood, and performance were evaluated through contest preparation. The participant lost 10.1kg throughout contest preparation in a strong weekly linear pattern (R 2 =0.97). Body fat was reduced from 30.45% to 15.85% while fat free mass was maintained. Mood for the participant remained stable until month five, when an observed variation occurred, with performance maintaining. Contest preparation was successful in reducing the body fat in the participant while having a minimum effect on both performance and fat free mass. For athletes looking to lose large amounts of body fat with minimal performance decrements a prolonged diet period with moderate exercise and food restriction can be an effective solution.

[The Contribution of Vascular Capacity and Blood Volume to Maintain Stable Blood Circulation during General Anesthesia].

PubMed

Shigemi, Kenji

2016-05-01

To maintain proper cardiac preload is one of the most effective procedures for the systemic circulation remaining stable. In particular, the balance between vascular capacity and total blood volume must be maintained within appropriate range by the administration of fluids, blood and/or vasoactive drugs with mean circulatory filling pressure (Pmcf), central venous pressure (CVP) or stroke volume variation (SVV). End-diastolic left ventricular volume (Ved) is theoretically the best index of cardiac preload; however, without transesophageal echocardbalanceiogram we cannot directly monitor Ved during anesthesia. The infused fluid volume remaining in intravascular space, the vascular capacity controlled by autonomic nervous system and/or vasoactive agents, and the unstressed blood volume properly mobilized to excess blood volume are the crucial factors to maintain cardiac output The knowledge of vascular physiology contribute the decision making to manipulate such factors to control blood circulation during general anesthesia. For example, CVP is usually maintained in the narrow range and seems to be stable; however, it must be changed just after the circulatory disturbances, such as acute bleeding, blood transfusion, and fluid infusion, and followed by gradual returning to initial value, because of the solid mechanism to preserve cardiac output

The String Stability of a Trajectory-Based Interval Management Algorithm in the Midterm Airspace

NASA Technical Reports Server (NTRS)

Swieringa, Kurt A.

2015-01-01

NASA's first Air Traffic Management (ATM) Technology Demonstration (ATD-1) was created to facilitate the transition of mature ATM technologies from the laboratory to operational use. The technologies selected for demonstration are the Traffic Management Advisor with Terminal Metering (TMA-TM), which provides precise time-based scheduling in the terminal airspace; Controller Managed Spacing (CMS), which provides terminal controllers with decision support tools enabling precise schedule conformance; and Interval Management (IM), which consists of flight deck automation that enables aircraft to achieve or maintain a precise spacing interval behind a target aircraft. As the percentage of IM equipped aircraft increases, controllers may provide IM clearances to sequences, or strings, of IM-equipped aircraft. It is important for these strings to maintain stable performance. This paper describes an analytic analysis of the string stability of the latest version of NASA's IM algorithm and a fast-time simulation designed to characterize the string performance of the IM algorithm. The analytic analysis showed that the spacing algorithm has stable poles, indicating that a spacing error perturbation will be reduced as a function of string position. The fast-time simulation investigated IM operations at two airports using constraints associated with the midterm airspace, including limited information of the target aircraft's intended speed profile and limited information of the wind forecast on the target aircraft's route. The results of the fast-time simulation demonstrated that the performance of the spacing algorithm is acceptable for strings of moderate length; however, there is some degradation in IM performance as a function of string position.

Towards colorless transparent organic transistors: potential of benzothieno[3,2-b]benzothiophene-based wide-gap semiconductors.

PubMed

Moon, Hanul; Cho, Hyunsu; Kim, Mincheol; Takimiya, Kazuo; Yoo, Seunghyup

2014-05-21

Colorless, highly transparent organic thin-film transistors (TOTFTs) with high performance are realized based on benzothieno[3,2-b]benzothiophene (BTBT) derivatives that simultaneously exhibit a wide energy gap and high transport properties. Multilayer transparent source/drain electrodes maintain the transparency, and ultrathin fluoropolymer dielectric layers enable stable, low-voltage operation of the proposed TOTFTs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Preparation of 3D Architecture Graphdiyne Nanosheets for High-Performance Sodium-Ion Batteries and Capacitors.

PubMed

Wang, Kun; Wang, Ning; He, Jianjiang; Yang, Ze; Shen, Xiangyan; Huang, Changshui

2017-11-22

Here, we apply three-dimensional (3D) architecture graphdiyne nanosheet (GDY-NS) as anode materials for sodium-ion storage devices achieving high energy and power performance along with excellent cyclic ability. The contribution of 3D architecture nanostructure and intramolecular pores of the GDY-NS can substantially optimize the sodium storage behavior through the accommodated intramolecular pore, 3D interconnective porous structure, and increased activity sites to facilitate a fast sodium-ion-diffusion channel. The contribution of butadiyne linkages and the formation of a stable solid electrolyte interface layer are directly confirmed through the in situ Raman measurement. The GDY-NS-based sodium-ion batteries exhibit a stable reversible capacity of approximately 812 mAh g -1 at a current density of 0.05 A g -1 ; they maintain more than 405 mAh g -1 over 1000 cycles at a current density of 1 A g -1 . Furthermore, the sodium-ion capacitors could deliver a capacitance more than 200 F g -1 over 3000 cycles at 1 A g -1 and display an initial specific energy as high as 182.3 Wh kg -1 at a power density of 300 W kg -1 and maintain specific energy of 166 Wh kg -1 even at a power density of 15 000 W kg -1 . The high energy and power density along with excellent cyclic performance based on the GDY-NS anode offers a great potential toward application on next-generation energy storage devices.

Relatedness predicts multiple measures of investment in cooperative nest construction in sociable weavers

PubMed Central

Leighton, Gavin M.; Echeverri, Sebastian; Heinrich, Dirk; Kolberg, Holger

2015-01-01

Although communal goods are often critical to society, they are simultaneously susceptible to exploitation and are evolutionarily stable only if mechanisms exist to curtail exploitation. Mechanisms such as punishment and kin selection have been offered as general explanations for how communal resources can be maintained. Evidence for these mechanisms comes largely from humans and social insects, leaving their generality in question. To assess how communal resources are maintained, we observed cooperative nest construction in sociable weavers (Philetairus socius). The communal nest of sociable weavers provides thermal benefits for all individuals but requires continual maintenance. We observed cooperative nest construction and also recorded basic morphological characteristics. We also collected blood samples, performed next-generation sequencing, and isolated 2358 variable single nucleotide polymorphisms (SNPs) to estimate relatedness. We find that relatedness predicts investment in cooperative nest construction, while no other morphological characters significantly explain cooperative output. We argue that indirect benefits are a critical fitness component for maintaining the cooperative behavior that maintains the communal good. PMID:26726282

Robust Pinhole-free Li3N Solid Electrolyte Grown from Molten Lithium

PubMed Central

2017-01-01

Lithium metal is the ultimate anode choice for high energy density rechargeable lithium batteries. However, it suffers from inferior electrochemical performance and safety issues due to its high reactivity and the growth of lithium dendrites. It has long been desired to develop a materials coating on Li metal, which is pinhole-free, mechanically robust without fracture during Li metal deposition and stripping, and chemically stable against Li metal and liquid electrolytes, all while maintaining adequate ionic conductivity. However, such an ideal material coating has yet to be found. Here we report a novel synthesis method by reacting clean molten lithium foil directly with pure nitrogen gas to generate instantaneously a pinhole-free and ionically conductive α-Li3N film directly bonded onto Li metal foil. The film consists of highly textured large Li3N grains (tens of μm) with (001) crystalline planes parallel to the Li metal surface. The bonding between textured grains is strong, resulting in a mechanically robust film which does not crack even when bent to a 0.8 cm curvature radius and is found to maintain pinhole-free coverage during Li metal deposition and stripping. The measured ionic conductivity is up to 5.2 × 10–4 S cm–1, sufficient for maintaining regular current densities for controllable film thicknesses ranging from 2 to 30 μm. This Li3N coating is chemically stable, isolating the reactive metallic lithium from liquid electrolyte, prevents continuous electrolyte consumption during battery cycling, and promotes dendrite-free uniform lithium plating/stripping underneath. We demonstrated Li|Li4Ti5O12 cells with stable and flat potential profiles for 500 cycles without capacity decay or an increase in potential hysteresis. PMID:29392181

Adaptive reliance on the most stable sensory predictions enhances perceptual feature extraction of moving stimuli.

PubMed

Kumar, Neeraj; Mutha, Pratik K

2016-03-01

The prediction of the sensory outcomes of action is thought to be useful for distinguishing self- vs. externally generated sensations, correcting movements when sensory feedback is delayed, and learning predictive models for motor behavior. Here, we show that aspects of another fundamental function-perception-are enhanced when they entail the contribution of predicted sensory outcomes and that this enhancement relies on the adaptive use of the most stable predictions available. We combined a motor-learning paradigm that imposes new sensory predictions with a dynamic visual search task to first show that perceptual feature extraction of a moving stimulus is poorer when it is based on sensory feedback that is misaligned with those predictions. This was possible because our novel experimental design allowed us to override the "natural" sensory predictions present when any action is performed and separately examine the influence of these two sources on perceptual feature extraction. We then show that if the new predictions induced via motor learning are unreliable, rather than just relying on sensory information for perceptual judgments, as is conventionally thought, then subjects adaptively transition to using other stable sensory predictions to maintain greater accuracy in their perceptual judgments. Finally, we show that when sensory predictions are not modified at all, these judgments are sharper when subjects combine their natural predictions with sensory feedback. Collectively, our results highlight the crucial contribution of sensory predictions to perception and also suggest that the brain intelligently integrates the most stable predictions available with sensory information to maintain high fidelity in perceptual decisions. Copyright © 2016 the American Physiological Society.

Functionally Stable and Phylogenetically Diverse Microbial Enrichments from Microbial Fuel Cells during Wastewater Treatment

PubMed Central

Ishii, Shun'ichi; Suzuki, Shino; Norden-Krichmar, Trina M.; Nealson, Kenneth H.; Sekiguchi, Yuji; Gorby, Yuri A.; Bretschger, Orianna

2012-01-01

Microbial fuel cells (MFCs) are devices that exploit microorganisms as biocatalysts to recover energy from organic matter in the form of electricity. One of the goals of MFC research is to develop the technology for cost-effective wastewater treatment. However, before practical MFC applications are implemented it is important to gain fundamental knowledge about long-term system performance, reproducibility, and the formation and maintenance of functionally-stable microbial communities. Here we report findings from a MFC operated for over 300 days using only primary clarifier effluent collected from a municipal wastewater treatment plant as the microbial resource and substrate. The system was operated in a repeat-batch mode, where the reactor solution was replaced once every two weeks with new primary effluent that consisted of different microbial and chemical compositions with every batch exchange. The turbidity of the primary clarifier effluent solution notably decreased, and 97% of biological oxygen demand (BOD) was removed after an 8–13 day residence time for each batch cycle. On average, the limiting current density was 1000 mA/m2, the maximum power density was 13 mW/m2, and coulombic efficiency was 25%. Interestingly, the electrochemical performance and BOD removal rates were very reproducible throughout MFC operation regardless of the sample variability associated with each wastewater exchange. While MFC performance was very reproducible, the phylogenetic analyses of anode-associated electricity-generating biofilms showed that the microbial populations temporally fluctuated and maintained a high biodiversity throughout the year-long experiment. These results suggest that MFC communities are both self-selecting and self-optimizing, thereby able to develop and maintain functional stability regardless of fluctuations in carbon source(s) and regular introduction of microbial competitors. These results contribute significantly toward the practical application of MFC systems for long-term wastewater treatment as well as demonstrating MFC technology as a useful device to enrich for functionally stable microbial populations. PMID:22347379

Implementation of an adaptive controller for the startup and steady-state running of a biomethanation process operated in the CSTR mode.

PubMed

Renard, P; Van Breusegem, V; Nguyen, M T; Naveau, H; Nyns, E J

1991-10-20

An adaptive control algorithm has been implemented on a biomethanation process to maintain propionate concentration, a stable variable, at a given low value, by steering the dilution rate. It was thereby expected to ensure the stability of the process during the startup and during steady-state running with an acceptable performance. The methane pilot reactor was operated in the completely mixed, once-through mode and computer-controlled during 161 days. The results yielded the real-life validation of the adaptive control algorithm, and documented the stability and acceptable performance expected.

ASDTIC: A feedback control innovation

NASA Technical Reports Server (NTRS)

Lalli, V. R.; Schoenfeld, A. D.

1972-01-01

The ASDTIC (Analog Signal to Discrete Time Interval Converter) control subsystem provides precise output control of high performance aerospace power supplies. The key to ASDTIC operation is that it stably controls output by sensing output energy change as well as output magnitude. The ASDTIC control subsystem and control module were developed to improve power supply performance during static and dynamic input voltage and output load variations, to reduce output voltage or current regulation due to component variations or aging, to maintain a stable feedback control with variations in the loop gain or loop time constants, and to standardize the feedback control subsystem for power conditioning equipment.

ASDTIC - A feedback control innovation.

NASA Technical Reports Server (NTRS)

Lalli, V. R.; Schoenfeld, A. D.

1972-01-01

The ASDTIC (analog signal to discrete time interval converter) control subsystem provides precise output control of high performance aerospace power supplies. The key to ASDTIC operation is that it stably controls output by sensing output energy change as well as output magnitude. The ASDTIC control subsystem and control module were developed to improve power supply performance during static and dynamic input voltage and output load variations, to reduce output voltage or current regulation due to component variations or aging, to maintain a stable feedback control with variations in the loop gain or loop time constants, and to standardize the feedback control subsystem for power conditioning equipment.

Long-Term Stability of Motor Cortical Activity: Implications for Brain Machine Interfaces and Optimal Feedback Control.

PubMed

Flint, Robert D; Scheid, Michael R; Wright, Zachary A; Solla, Sara A; Slutzky, Marc W

2016-03-23

The human motor system is capable of remarkably precise control of movements--consider the skill of professional baseball pitchers or surgeons. This precise control relies upon stable representations of movements in the brain. Here, we investigated the stability of cortical activity at multiple spatial and temporal scales by recording local field potentials (LFPs) and action potentials (multiunit spikes, MSPs) while two monkeys controlled a cursor either with their hand or directly from the brain using a brain-machine interface. LFPs and some MSPs were remarkably stable over time periods ranging from 3 d to over 3 years; overall, LFPs were significantly more stable than spikes. We then assessed whether the stability of all neural activity, or just a subset of activity, was necessary to achieve stable behavior. We showed that projections of neural activity into the subspace relevant to the task (the "task-relevant space") were significantly more stable than were projections into the task-irrelevant (or "task-null") space. This provides cortical evidence in support of the minimum intervention principle, which proposes that optimal feedback control (OFC) allows the brain to tightly control only activity in the task-relevant space while allowing activity in the task-irrelevant space to vary substantially from trial to trial. We found that the brain appears capable of maintaining stable movement representations for extremely long periods of time, particularly so for neural activity in the task-relevant space, which agrees with OFC predictions. It is unknown whether cortical signals are stable for more than a few weeks. Here, we demonstrate that motor cortical signals can exhibit high stability over several years. This result is particularly important to brain-machine interfaces because it could enable stable performance with infrequent recalibration. Although we can maintain movement accuracy over time, movement components that are unrelated to the goals of a task (such as elbow position during reaching) often vary from trial to trial. This is consistent with the minimum intervention principle of optimal feedback control. We provide evidence that the motor cortex acts according to this principle: cortical activity is more stable in the task-relevant space and more variable in the task-irrelevant space. Copyright © 2016 the authors 0270-6474/16/363623-10$15.00/0.

Soviet Relations with Japan: Poor Treatment of a Valuable Trade Partner

DTIC Science & Technology

1977-01-01

Thus, Japan has repeatedly been urged to take better advantage of the "international division of labor Ŗ since the *stable socialist foreign trade...some of the problems of the seventies, including the absence of abundant reserves of labor with which to maintain a high growth rate. An already high...and a concurrent decrease in the growth of total output (expected for a more mature economy at high performance levels). 7 must improve overall labor

Utilization of MRI for Cerebral White Matter Injury in a Hypobaric Swine Model-Validation of Technique

DTIC Science & Technology

2017-05-23

study demonstrates high reproducibility of quantitative noninvasive MRI, suggesting MRI is an appropriate assessment tool for TBI and hypobaric-induced...propofol/ketamine adjusted to maintain stable physiological parameters and anesthesia. On study day 1, baseline imaging was performed. Exposure episodes...began on study day 3 with three subject animals exposed six times to 9,144 meters (ascent/descent time 15 minutes) over 12 days, one exposed five times

Evaluation of working conditions of workers engaged in tending horses.

PubMed

Nowakowicz-Dębek, Bożena; Pawlak, Halina; Wlazło, Łukasz; Kuna-Broniowska, Izabela; Bis-Wencel, Hanna; Buczaj, Agnieszka; Maksym, Piotr

2014-01-01

A growing interest in the horse business has resulted in the increased engagement of many people in this area, and the health problems occurring among workers create the need to search for prophylactic measures. The objective of the study was evaluation of the level of exposure to air pollution in a stable, and estimation of the degree of work load among workers engaged in tending horses. The study was conducted twice, during the winter season, in a stable maintaining race horses, and in a social room. In order to evaluate workers' exposure, air samples were collected by the aspiration method. After the incubation of material, the total number of bacteria and fungi in the air was determined, as well as the number of aerobic mesophilic and thermophilic bacteria, expressed as the number of colony forming units per cubic meter of air (CFU/m3). The measurement of total dust concentration in the air was also performed, simultaneously with the measurement of microclimatic parameters. The study of work load also covered the measurement of energy expenditure, evaluation of static physical load, and monotony of movements performed. The stable may be considered as a workplace with considerable risk of the occurrence of unfavourable health effects.

Investigation of grafted ETFE-based polymer membranes as alternative electrolyte for direct methanol fuel cells

NASA Astrophysics Data System (ADS)

Aricò, A. S.; Baglio, V.; Cretı̀, P.; Di Blasi, A.; Antonucci, V.; Brunea, J.; Chapotot, A.; Bozzi, A.; Schoemans, J.

Low cost ethylene-tetrafluoroethylene (ETFE)-based grafted membranes have been prepared by a process based on electron beam irradiation, subsequent grafting, cross-linking and sulfonation procedure. Two different grafted membranes varying by their grafting and cross-linking levels have been investigated for applications in direct methanol fuel cells (DMFCs) operating between 90 and 130 °C. DMFC assemblies based on these membranes showed cell resistance and performance values comparable to Nafion 117. Stable electrochemical performance was recorded during 1 month of cycled operation. Tailoring of grafting and cross-linking properties allows a significant reduction of methanol cross-over while maintaining suitable conductivity and performance levels.

Surface tiny grain-dependent enhanced rate performance of MoO3 nanobelts with pseudocapacitance contribution for lithium-ion battery anode

NASA Astrophysics Data System (ADS)

Cao, Liyun; He, Juju; Li, Jiayin; Yan, Jingwen; Huang, Jianfeng; Qi, Ying; Feng, Liangliang

2018-07-01

In order to improve the rate performance of MoO3, a novel MoO3 nanobelt with tiny grains on surface (named as d-MoO3) is fabricated via one-step facile hydrothermal method with citric acid adding, in which citric acid (CA) serves as a weak reductant as well as surface modification agent. When tested as an anode in LIBs, d-MoO3 displays an improved discharge capacity of 787 mAh·g-1 at 0.1 A g-1 over 100 cycles with capacity retention of ∼91% while MoO3 decays to 50 mAh·g-1 in the 100th cycle. Notably, d-MoO3 delivers enhanced rate capability (536 and 370 mAh·g-1 at high rates of 5 and 10 A g-1 respectively). We consider these excellent electrochemical properties of d-MoO3 electrode are associated with the tiny grains on MoO3 surface, which effectively maintains the electrode's structural integrity. Even though d-MoO3 nanobelt suffers from a degree of in-situ pulverization after several cycles, these pulverized active particles can still maintain stable electrochemical contact and are highly exposed to electrolyte, realizing ultrahigh e-/Li+ diffusion kinetics. In addition, part extrinsic pseudocapacitance contribution to the Li+ storage also explains the high-rate performance. Combining all these merits, d-MoO3 is potentially a high-energy, high-power and well-stable anode material for Li ion batteries (LIBs).

[Establishment and characterization of a new carcinoma cell line from uterine cervix of Uyghur women].

PubMed

Zhang, Lu; Aerziguli, Tursun; Guzalnur, Abliz

2012-04-01

To establish a uterine cervical carcinoma cell line of Uyghur ethnical background and to evaluate the related biological characteristics for future biomedical investigations of diseases in the Uyghur population. Poorly-differentiated squamous cell carcinoma specimens of Uyghur patients were obtained and cultured in vitro by enzymatic digestion method, followed by continuous passaging to reach a stable growth determined by cell viability and growth curve. Morphological study, cell cycling and chromosomal analysis were performed. Tumorigenesis study was conducted by inoculation of nude mice. Biomarker (CK17, CD44, Ki-67, CK14 and vimentin) expression was detected by immunofluorescence and immunocytochemical techniques. A cervical carcinoma cell line was successfully established and maintained for 12 months through 70 passages. The cell line had a stable growth with a population doubling time of 51.9 h. Flask method and double agar-agar assay showed that the cell line had colony-forming rates of 32.5% and 15.6%, respectively. Ultrastructural evaluation demonstrated numerous cell surface protrusions or microvilli, a large number of rod-shape structures in cytoplasm, typical desmosomes and nuclear atypia. Chromosomal analysis revealed human karyotype with the number of chromosomes per cell varying from 32 - 97 with a majority of 54 - 86 (60.3%). Xenogeneic tumors formed in nude mice showed histological structures identical to those of the primary tumor. The cells had high expression of CK17, CD44, Ki-67 and vimentin but no CK14 expression. A cervical carcinoma cell line from a female Uyghur patient is successfully established. The cell line has the characteristics of human cervical squamous cell carcinoma, and it is stable with maintaining the characteristic biological and morphological features in vitro for more than 12 months, therefore, qualified as a stable cell line for further biomedical research.

Compiler-assisted static checkpoint insertion

NASA Technical Reports Server (NTRS)

Long, Junsheng; Fuchs, W. K.; Abraham, Jacob A.

1992-01-01

This paper describes a compiler-assisted approach for static checkpoint insertion. Instead of fixing the checkpoint location before program execution, a compiler enhanced polling mechanism is utilized to maintain both the desired checkpoint intervals and reproducible checkpoint 1ocations. The technique has been implemented in a GNU CC compiler for Sun 3 and Sun 4 (Sparc) processors. Experiments demonstrate that the approach provides for stable checkpoint intervals and reproducible checkpoint placements with performance overhead comparable to a previously presented compiler assisted dynamic scheme (CATCH) utilizing the system clock.

Ultra-stable long distance optical frequency distribution using the Internet fiber network.

PubMed

Lopez, Olivier; Haboucha, Adil; Chanteau, Bruno; Chardonnet, Christian; Amy-Klein, Anne; Santarelli, Giorgio

2012-10-08

We report an optical link of 540 km for ultrastable frequency distribution over the Internet fiber network. The stable frequency optical signal is processed enabling uninterrupted propagation on both directions. The robustness and the performance of the link are enhanced by a cost effective fully automated optoelectronic station. This device is able to coherently regenerate the return optical signal with a heterodyne optical phase locking of a low noise laser diode. Moreover the incoming signal polarization variation are tracked and processed in order to maintain beat note amplitudes within the operation range. Stable fibered optical interferometer enables optical detection of the link round trip phase signal. The phase-noise compensated link shows a fractional frequency instability in 10 Hz bandwidth of 5 × 10(-15) at one second measurement time and 2 × 10(-19) at 30,000 s. This work is a significant step towards a sustainable wide area ultrastable optical frequency distribution and comparison network.

Sub-100 fs pulses from an all-polarization maintaining Yb-fiber oscillator with an anomalous dispersion higher-order-mode fiber.

PubMed

Verhoef, A J; Zhu, L; Israelsen, S Møller; Grüner-Nielsen, L; Unterhuber, A; Kautek, W; Rottwitt, K; Baltuška, A; Fernández, A

2015-10-05

We present an Yb-fiber oscillator with an all-polarization-maintaining cavity with a higher-order-mode fiber for dispersion compensation. The polarization maintaining higher order mode fiber introduces not only negative second order dispersion but also negative third order dispersion in the cavity, in contrast to dispersion compensation schemes used in previous demonstrations of all-polarization maintaining Yb-fiber oscillators. The performance of the saturable absorber mirror modelocked oscillator, that employs a free space scheme for coupling onto the saturable absorber mirror and output coupling, was investigated for different settings of the intracavity dispersion. When the cavity is operated with close to zero net dispersion, highly stable 0.5-nJ pulses externally compressed to sub-100-fs are generated. These are to our knowledge the shortest pulses generated from an all-polarization-maintaining Yb-fiber oscillator. The spectral phase of the output pulses is well behaved and can be compensated such that wing-free Fourier transform limited pulses can be obtained. Further reduction of the net intracavity third order dispersion will allow generating broader output spectra and consequently shorter pulses, without sacrificing pulse fidelity.

The role of moisture in the nest thermoregulation of social wasps.

PubMed

Klingner, R; Richter, K; Schmolz, E; Keller, B

2005-09-01

Paper nests of social wasps are intriguing constructions for both, biologists and engineers. We demonstrate that moisture and latent heat significantly influence the thermal performance of the nest construction. Two colonies of the hornet Vespa crabro were investigated in order to clarify the relation of the temperature and the moisture regime inside the nest. Next to fairly stable nest temperatures the hornets maintain a high relative humidity inside the nest. We found that in consequence a partial vapor-pressure gradient between nest and ambient drives a constant vapor flux through the envelope. The vapor flux is limited by the diffusion resistance of the envelope. The driving force of vapor flux is heat, which is consumed through evaporation inside the nest. The colony has to compensate this loss with metabolic heat production in order to maintain a stable nest temperature. However, humidity fluctuations inside the nest induce circadian adsorption and desorption cycles, which stabilize the nest temperature and thus contribute significantly to temperature homeostasis. Our study demonstrates that both mechanisms influence nest thermoregulation and need to be considered to understand the thermodynamic behavior of nests of wasps and social insects in general.

Monolithic amplifier with stable, high resistance feedback element and method for fabricating the same

DOEpatents

O'Connor, Paul

1998-08-11

A monolithic amplifier includes a stable, high resistance feedback circuit and a dynamic bias circuit. The dynamic bias circuit is formed with active elements matched to those in the amplifier and feedback circuit to compensate for variations in the operating and threshold voltages thereby maintaining a stable resistance in the feedback circuit.

Producing High-Performance, Stable, Sheared-Flow Z-Pinches in the FuZE project

NASA Astrophysics Data System (ADS)

Golingo, R. P.; Shumlak, U.,; Nelson, B. A.; Claveau, E. L.; Forbes, E. G.; Stepanov, A. D.; Weber, T. R.; Zhang, Y.; McLean, H. S.; Tummel, K. K.; Higginson, D. P.; Schmidt, A. E.; University of Washington (UW) Collaboration; Lawrence Livermore National Laboratory (LLNL) Collaboration

2017-10-01

The Fusion Z-Pinch Experiment (FuZE) has made significant strides towards generating high-performance, stable Z-pinch plasmas with goals of ne = 1018 cm-3 and T =1 keV. The Z-pinch plasmas are stabilized with a sheared axial flow that is driven by a coaxial accelerator. The new FuZE device has been constructed and reproduces the major scientific achievements the ZaP project at the University of Washington; ne = 1016 cm-3,T = 100 eV, r<1 cm, and tstable >20 μs. These parameters are measured with an array of magnetic field probes, spectroscopy, and fast framing cameras. The plasma parameters are achieved using a small fraction of the maximum energy storage and gas injection capability of the FuZE device. Higher density, ne = 5×1017 cm-3, and temperature, T = 500 eV, Z-pinch plasmas are formed by increasing the pinch current. At the higher voltages and currents, the ionization rates in the accelerator increase. By modifying the neutral gas profile in the accelerator, the plasma flow from the accelerator is maintained, driving the flow shear. Formation and sustainment of the sheared-flow Z-pinch plasma will be discussed. Experimental data demonstrating high performance plasmas in a stable Z-pinches will be shown. This work is supported by an award from US ARPA-E.

Exploiting nonlinear properties of pure and Sn-doped Bi2Te2Se for passive Q-switching of all-polarization maintaining ytterbium- and erbium-doped fiber lasers.

PubMed

Bogusławski, Jakub; Kowalczyk, Maciej; Iwanowski, Przemysław; Hruban, Andrzej; Diduszko, Ryszard; Piotrowski, Kazimierz; Dybko, Krzysztof; Wojciechowski, Tomasz; Aleszkiewicz, Marta; Sotor, Jarosław

2017-08-07

Due to their broadband nonlinear optical properties, low-dimensional materials are widely used for pulse generation in fiber and solid-state lasers. Here we demonstrate novel materials, Bi 2 Te 2 Se (BTS) and Sn-doped Bi 2 Te 2 Se (BSTS), which can be used as a universal saturable absorbers for distinct spectral regimes. The material was mechanically exfoliated from a bulk single-crystal and deposited onto a side-polished fiber. We have performed characterization of the fabricated devices and employed them in polarization-maintaining ytterbium- and erbium-doped fiber lasers. This enabled us to obtain self-starting passively Q-switched regime at 1 µm and 1.56 µm. The oscillators emitted stable, linearly polarized radiation with the highest single pulse energy approaching 692 nJ. Both lasers are characterized by the best performance observed in all-polarization maintaining Q-switched fiber lasers with recently investigated new saturable absorbers, which was enabled by a very high damage threshold of the devices. This demonstrates the great potential of the investigated materials for the ultrafast photonics community.

Effects of organic composition on mesophilic anaerobic digestion of food waste.

PubMed

Li, Yangyang; Jin, Yiying; Borrion, Aiduan; Li, Hailong; Li, Jinhui

2017-11-01

Anaerobic digestion of food waste (FW) has been widely investigated, however, little is known about the influence of organic composition on the FW digestion process. This study aims to identify the optimum composition ratios of carbohydrate (CA), protein (CP) and lipid (EE) for maintaining high methane yield and process stability. The results show that the CA-CP-EE ratio was significantly correlated with performance and degradability parameters. Controlling the CA-CP-EE ratio higher than 1.89 (CA higher than 8.3%, CP lower than 5.0%, and EE lower than 5.6%) could be an effective way to maintain stable digestion and achieve higher methane production (385-627mL/gVS) and shorter digestion retention (196-409h). The CA-CP-EE ratio could be used as an important indicator for digestion performance. To effectively evaluate organic reduction, the concentration and removal efficiency of organic compositions in both solid phases and total FW should be considered. Copyright © 2017. Published by Elsevier Ltd.

Monolithic amplifier with stable, high resistance feedback element and method for fabricating the same

DOEpatents

O`Connor, P.

1998-08-11

A monolithic amplifier includes a stable, high resistance feedback circuit and a dynamic bias circuit. The dynamic bias circuit is formed with active elements matched to those in the amplifier and feedback circuit to compensate for variations in the operating and threshold voltages thereby maintaining a stable resistance in the feedback circuit. 11 figs.

Hydroponic system design with real time OS based on ARM Cortex-M microcontroller

NASA Astrophysics Data System (ADS)

Atmadja, Wiedjaja; Liawatimena, Suryadiputra; Lukas, Jonathan; Nata, Eka Putra Leo; Alexander, Ivan

2017-12-01

Hydroponic is the process of growing plants without soil, plant root flooded or moist with nutrient-rich solutions in inert material. Hydroponics has become a reality for greenhouse growers in virtually all climates. Large hydroponic installations exist throughout the world for growing flowers, vegetables and some short period fruit like tomato and cucumber. In soilless culture, we must maintain stable pH and conductivity level of nutrient solution to make plant grow well, large variation of pH of certain time will poisoned plant. This paper describes development complete automation hydroponic system, from maintaining stable nutrient composition (conductivity and pH), grow light, and monitor plant environment such as CO2, temperature and humidity. The heart of our automation is ARM Cortex-M4 from ST Microelectronic running ARM mbed OS, the official Real Time Operating System (RTOS) for ARM Cortex-M microcontroller. Using RTOS gives us flexibility to have multithreaded process. Results show that system capable to control desired concentration level with variation of less than 3%, pH sensor show good accuracy 5.83% from pH value 3.23-10. Growing light intensity measurement show result 105 μmol/m2/s therefore we need turn on the light at least 17 hours/day to fulfil plant light requirement. RTOS give good performance with latency and jitter less than 15 us, system overall show good performance and accuracy for automating hydroponic plant in vegetative phase of growth.

Performance and microbial community composition dynamics of aerobic granular sludge from sequencing batch bubble column reactors operated at 20 degrees C, 30 degrees C, and 35 degrees C.

PubMed

Ebrahimi, Sirous; Gabus, Sébastien; Rohrbach-Brandt, Emmanuelle; Hosseini, Maryam; Rossi, Pierre; Maillard, Julien; Holliger, Christof

2010-07-01

Two bubble column sequencing batch reactors fed with an artificial wastewater were operated at 20 degrees C, 30 degrees C, and 35 degrees C. In a first stage, stable granules were obtained at 20 degrees C, whereas fluffy structures were observed at 30 degrees C. Molecular analysis revealed high abundance of the operational taxonomic unit 208 (OTU 208) affiliating with filamentous bacteria Leptothrix spp. at 30 degrees C, an OTU much less abundant at 20 degrees C. The granular sludge obtained at 20 degrees C was used for the second stage during which one reactor was maintained at 20 degrees C and the second operated at 30 degrees C and 35 degrees C after prior gradual increase of temperature. Aerobic granular sludge with similar physical properties developed in both reactors but it had different nutrient elimination performances and microbial communities. At 20 degrees C, acetate was consumed during anaerobic feeding, and biological phosphorous removal was observed when Rhodocyclaceae-affiliating OTU 214 was present. At 30 degrees C and 35 degrees C, acetate was mainly consumed during aeration and phosphorous removal was insignificant. OTU 214 was almost absent but the Gammaproteobacteria-affiliating OTU 239 was more abundant than at 20 degrees C. Aerobic granular sludge at all temperatures contained abundantly the OTUs 224 and 289 affiliating with Sphingomonadaceae indicating that this bacterial family played an important role in maintaining stable granular structures.

Pilot plant demonstration of stable and efficient high rate biological nutrient removal with low dissolved oxygen conditions.

PubMed

Keene, Natalie A; Reusser, Steve R; Scarborough, Matthew J; Grooms, Alan L; Seib, Matt; Santo Domingo, Jorge; Noguera, Daniel R

2017-09-15

Aeration in biological nutrient removal (BNR) processes accounts for nearly half of the total electricity costs at many wastewater treatment plants. Even though conventional BNR processes are usually operated to have aerated zones with high dissolved oxygen (DO) concentrations, recent research has shown that nitrification can be maintained using very low-DO concentrations (e.g., below 0.2 mg O 2 /L), and therefore, it may be possible to reduce energy use and costs in BNR facilities by decreasing aeration. However, the effect of reduced aeration on enhanced biological phosphorus removal (EBPR) is not understood. In this study, we investigated, at the pilot-scale level, the effect of using minimal aeration on the performance of an EBPR process. Over a 16-month operational period, we performed stepwise decreases in aeration, reaching an average DO concentration of 0.33 mg O 2 /L with stable operation and nearly 90% phosphorus removal. Under these low-DO conditions, nitrification efficiency was maintained, and nearly 70% of the nitrogen was denitrified, without the need for internal recycling of high nitrate aeration basin effluent to the anoxic zone. At the lowest DO conditions used, we estimate a 25% reduction in energy use for aeration compared to conventional BNR operation. Our improved understanding of the efficiency of low-DO BNR contributes to the global goal of reducing energy consumption during wastewater treatment operations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Stability and Structure of Star-Shape Granules

NASA Astrophysics Data System (ADS)

Zhao, Yuchen; Bares, Jonathan; Zheng, Matthew; Dierichs, Karola; Menges, Achim; Behringer, Robert

2015-11-01

Columns are made of convex non-cohesive grains like sand collapse after being released from initial positions. On the other hand, various architectures built by concave grains can maintain stability. We explore why these structures are stable, and how stable they can be. We performed experiments by randomly pouring identical star-shape particles into hollow cylinders left on glass and a rough base, and observed stable granular columns after lifting the cylinders. Particles have six 9 mm arms, which extend symmetrically in the xyz directions. Both the probability of creating a stable column and mechanical stability aspects have been investigated. We define r as the weight fraction of particles that fall out of the column after removing confinement. r gradually increases as the column height increases, or the column diameter decreases. We also explored different experiment conditions such as vibration of columns with confinement, or large basal friction. We also consider different stability measures such as the maximum inclination angle or maximum weight a column can support. In order to understand structure leading to stability, 3D CT scan reconstructions of columns have been done and coordination number and packing density will be discussed. We acknowledge supports from W.M.Keck Foundation and Research Triangle MRSEC.

Driving performance of stable outpatients with depression undergoing real-world treatment.

PubMed

Miyata, Akemi; Iwamoto, Kunihiro; Kawano, Naoko; Aleksic, Branko; Ando, Masahiko; Ebe, Kazutoshi; Fujita, Kiyoshi; Yokoyama, Motonori; Akiyama, Tsuyoshi; Igarashi, Yoshio; Ozaki, Norio

2018-06-01

Although the effects of psychotropics on driving ability have received much attention, little research is available on driving performance of stable outpatients with depression undergoing real-world treatment. This observational study investigated driving performance, cognitive functions, and depressive symptomatology of partly remitted outpatients with depression under daily-practice psychopharmacologic treatment. Seventy stable outpatients with depression and 67 healthy volunteers were enrolled. Patients' prescriptions were not controlled in order to capture the real-world treatment environment. Participants underwent three driving tasks - road-tracking, car-following, and harsh-braking - using a driving simulator, and three cognitive tasks - Continuous Performance Test, Wisconsin Card Sorting Test, and Trail-Making Test. The Symptom Assessment Scale - Structured Interview Guide for the Hamilton Depression Rating Scale, Beck Depression Inventory-II, Social Adaptation Self-Evaluation Scale, and Stanford Sleepiness Scale were also completed. Although many patients received various pharmacologic treatments, there were no significant differences in the three driving tasks between outpatients with depression and healthy controls. Difficulty of maintaining set in the Wisconsin Card Sorting Test was significantly increased in patients with depression. Results on the Social Adaptation Self-Evaluation Scale were significantly associated with road-tracking and car-following performance, in contrast to results on the Hamilton Depression Rating Scale and the Beck Depression Inventory-II. We conclude that partly remitted depressive patients under steady-state pharmacologic treatment do not differ from healthy controls with respect to driving performance, which seems to be more affected by psychosocial functioning than by pharmacologic agents. This, however, should be investigated systematically in an off/on study. © 2018 The Authors. Psychiatry and Clinical Neurosciences © 2018 Japanese Society of Psychiatry and Neurology.

Effect of protein and energy intakes on body composition in non-diabetic maintenance-hemodialysis patients.

PubMed

Ichikawa, Yoko; Hiramatsu, Fumie; Hamada, Hisayo; Sakai, Atsuko; Hara, Keiko; Kogirima, Miho; Kawahara, Kazuhiko; Minakuchi, Jun; Kawashima, Shu; Yamamoto, Shigeru

2007-10-01

This cross sectional study was performed to find the adequate amount and combination of dietary protein and energy for maintaining better nutritional status for stable non-diabetic maintenance hemodialysis (MHD) patients. The body composition including body fat, total body water, body cell mass and body protein were measured by multi-frequency bioelectrical impedance analysis in 200 stable MHD patients without diabetes (124 men, 76 women). Dietary energy intake (DEI) and dietary protein intake (DPI) were assessed by a brief self-administered diet history questionnaire (BDHQ), the DPI value being confirmed by calculating the normalized protein equivalent of total nitrogen appearance (nPNA). The nutritional status and the body composition were compared among 4 groups of patients in each gender that were divided by the combination of DEI and DPI; high energy (HE)/high protein (HP), HE/low protein (LP), low energy (LE)/HP and LE/LP groups. The mean DPI ranged between 1.17-1.23 and 0.89-0.95 g/kg IBW/d in the HP and LP groups, respectively for both genders, and the mean DEI was 35-37 and 24-25 kcal/kg IBW/d in HE and LE groups, respectively. BMI and serum albumin concentration were not different among the 4 groups. Body cell mass index (BCMI) was maintained in the HE groups regardless of DPI, and it was significantly higher in the HE/HP group than in the LE/LP group. Multiple regression analysis also showed that the BCMI was more greatly affected by DEI than DPI. These results indicated that a DPI of 0.89-0.95 g/kg IBW/d could be sufficient for maintaining BCMI, if DEI is kept over 35 kcal/kg IBW/d in stable non-diabetic MHD patients. This DPI level is lower than the recommended DPI proposed by dietary guidelines in the US and Japan.

An intermittent control model of flexible human gait using a stable manifold of saddle-type unstable limit cycle dynamics

PubMed Central

Fu, Chunjiang; Suzuki, Yasuyuki; Kiyono, Ken; Morasso, Pietro; Nomura, Taishin

2014-01-01

Stability of human gait is the ability to maintain upright posture during walking against external perturbations. It is a complex process determined by a number of cross-related factors, including gait trajectory, joint impedance and neural control strategies. Here, we consider a control strategy that can achieve stable steady-state periodic gait while maintaining joint flexibility with the lowest possible joint impedance. To this end, we carried out a simulation study of a heel-toe footed biped model with hip, knee and ankle joints and a heavy head-arms-trunk element, working in the sagittal plane. For simplicity, the model assumes a periodic desired joint angle trajectory and joint torques generated by a set of feed-forward and proportional-derivative feedback controllers, whereby the joint impedance is parametrized by the feedback gains. We could show that a desired steady-state gait accompanied by the desired joint angle trajectory can be established as a stable limit cycle (LC) for the feedback controller with an appropriate set of large feedback gains. Moreover, as the feedback gains are decreased for lowering the joint stiffness, stability of the LC is lost only in a few dimensions, while leaving the remaining large number of dimensions quite stable: this means that the LC becomes saddle-type, with a low-dimensional unstable manifold and a high-dimensional stable manifold. Remarkably, the unstable manifold remains of low dimensionality even when the feedback gains are decreased far below the instability point. We then developed an intermittent neural feedback controller that is activated only for short periods of time at an optimal phase of each gait stride. We characterized the robustness of this design by showing that it can better stabilize the unstable LC with small feedback gains, leading to a flexible gait, and in particular we demonstrated that such an intermittent controller performs better if it drives the state point to the stable manifold, rather than directly to the LC. The proposed intermittent control strategy might have a high affinity for the inverted pendulum analogy of biped gait, providing a dynamic view of how the step-to-step transition from one pendular stance to the next can be achieved stably in a robust manner by a well-timed neural intervention that exploits the stable modes embedded in the unstable dynamics. PMID:25339687

An intermittent control model of flexible human gait using a stable manifold of saddle-type unstable limit cycle dynamics.

PubMed

Fu, Chunjiang; Suzuki, Yasuyuki; Kiyono, Ken; Morasso, Pietro; Nomura, Taishin

2014-12-06

Stability of human gait is the ability to maintain upright posture during walking against external perturbations. It is a complex process determined by a number of cross-related factors, including gait trajectory, joint impedance and neural control strategies. Here, we consider a control strategy that can achieve stable steady-state periodic gait while maintaining joint flexibility with the lowest possible joint impedance. To this end, we carried out a simulation study of a heel-toe footed biped model with hip, knee and ankle joints and a heavy head-arms-trunk element, working in the sagittal plane. For simplicity, the model assumes a periodic desired joint angle trajectory and joint torques generated by a set of feed-forward and proportional-derivative feedback controllers, whereby the joint impedance is parametrized by the feedback gains. We could show that a desired steady-state gait accompanied by the desired joint angle trajectory can be established as a stable limit cycle (LC) for the feedback controller with an appropriate set of large feedback gains. Moreover, as the feedback gains are decreased for lowering the joint stiffness, stability of the LC is lost only in a few dimensions, while leaving the remaining large number of dimensions quite stable: this means that the LC becomes saddle-type, with a low-dimensional unstable manifold and a high-dimensional stable manifold. Remarkably, the unstable manifold remains of low dimensionality even when the feedback gains are decreased far below the instability point. We then developed an intermittent neural feedback controller that is activated only for short periods of time at an optimal phase of each gait stride. We characterized the robustness of this design by showing that it can better stabilize the unstable LC with small feedback gains, leading to a flexible gait, and in particular we demonstrated that such an intermittent controller performs better if it drives the state point to the stable manifold, rather than directly to the LC. The proposed intermittent control strategy might have a high affinity for the inverted pendulum analogy of biped gait, providing a dynamic view of how the step-to-step transition from one pendular stance to the next can be achieved stably in a robust manner by a well-timed neural intervention that exploits the stable modes embedded in the unstable dynamics.

Scalable 96-well Plate Based iPSC Culture and Production Using a Robotic Liquid Handling System.

PubMed

Conway, Michael K; Gerger, Michael J; Balay, Erin E; O'Connell, Rachel; Hanson, Seth; Daily, Neil J; Wakatsuki, Tetsuro

2015-05-14

Continued advancement in pluripotent stem cell culture is closing the gap between bench and bedside for using these cells in regenerative medicine, drug discovery and safety testing. In order to produce stem cell derived biopharmaceutics and cells for tissue engineering and transplantation, a cost-effective cell-manufacturing technology is essential. Maintenance of pluripotency and stable performance of cells in downstream applications (e.g., cell differentiation) over time is paramount to large scale cell production. Yet that can be difficult to achieve especially if cells are cultured manually where the operator can introduce significant variability as well as be prohibitively expensive to scale-up. To enable high-throughput, large-scale stem cell production and remove operator influence novel stem cell culture protocols using a bench-top multi-channel liquid handling robot were developed that require minimal technician involvement or experience. With these protocols human induced pluripotent stem cells (iPSCs) were cultured in feeder-free conditions directly from a frozen stock and maintained in 96-well plates. Depending on cell line and desired scale-up rate, the operator can easily determine when to passage based on a series of images showing the optimal colony densities for splitting. Then the necessary reagents are prepared to perform a colony split to new plates without a centrifugation step. After 20 passages (~3 months), two iPSC lines maintained stable karyotypes, expressed stem cell markers, and differentiated into cardiomyocytes with high efficiency. The system can perform subsequent high-throughput screening of new differentiation protocols or genetic manipulation designed for 96-well plates. This technology will reduce the labor and technical burden to produce large numbers of identical stem cells for a myriad of applications.

The motion control of a statically stable biped robot on an uneven floor.

PubMed

Shih, C L; Chiou, C J

1998-01-01

This work studies the motion control of a statically stable biped robot having seven degrees of freedom. Statically stable walking of the biped robot is realized by maintaining the center-of-gravity inside the convex region of the supporting foot and/or feet during both single-support and double-support phases. The main points of this work are framing the stability in an easy and correct way, the design of a bipedal statically stable walker, and walking on sloping surfaces and stairs.

Remembering to learn: independent place and journey coding mechanisms contribute to memory transfer.

PubMed

Bahar, Amir S; Shapiro, Matthew L

2012-02-08

The neural mechanisms that integrate new episodes with established memories are unknown. When rats explore an environment, CA1 cells fire in place fields that indicate locations. In goal-directed spatial memory tasks, some place fields differentiate behavioral histories ("journey-dependent" place fields) while others do not ("journey-independent" place fields). To investigate how these signals inform learning and memory for new and familiar episodes, we recorded CA1 and CA3 activity in rats trained to perform a "standard" spatial memory task in a plus maze and in two new task variants. A "switch" task exchanged the start and goal locations in the same environment; an "altered environment" task contained unfamiliar local and distal cues. In the switch task, performance was mildly impaired, new firing maps were stable, but the proportion and stability of journey-dependent place fields declined. In the altered environment, overall performance was strongly impaired, new firing maps were unstable, and stable proportions of journey-dependent place fields were maintained. In both tasks, memory errors were accompanied by a decline in journey codes. The different dynamics of place and journey coding suggest that they reflect separate mechanisms and contribute to distinct memory computations. Stable place fields may represent familiar relationships among environmental features that are required for consistent memory performance. Journey-dependent activity may correspond with goal-directed behavioral sequences that reflect expectancies that generalize across environments. The complementary signals could help link current events with established memories, so that familiarity with either a behavioral strategy or an environment can inform goal-directed learning.

REMEMBERING TO LEARN: INDEPENDENT PLACE AND JOURNEY CODING MECHANISMS CONTRIBUTE TO MEMORY TRANSFER

PubMed Central

Bahar, Amir S.; Shapiro, Matthew L.

2012-01-01

The neural mechanisms that integrate new episodes with established memories are unknown. When rats explore an environment, CA1 cells fire in place fields that indicate locations. In goal-directed spatial memory tasks, some place fields differentiate behavioral histories (journey-dependent place fields) while others do not (journey-independent place fields). To investigate how these signals inform learning and memory for new and familiar episodes, we recorded CA1 and CA3 activity in rats trained to perform a standard spatial memory task in a plus maze and in two new task variants. A switch task exchanged the start and goal locations in the same environment; an altered environment task contained unfamiliar local and distal cues. In the switch task, performance was mildly impaired, new firing maps were stable, but the proportion and stability of journey-dependent place fields declined. In the altered environment, overall performance was strongly impaired, new firing maps were unstable, and stable proportions of journey-dependent place fields were maintained. In both tasks, memory errors were accompanied by a decline in journey codes. The different dynamics of place and journey coding suggest that they reflect separate mechanisms and contribute to distinct memory computations. Stable place fields may represent familiar relationships among environmental features that are required for consistent memory performance. Journey-dependent activity may correspond with goal directed behavioral sequences that reflect expectancies that generalize across environments. The complementary signals could help link current events with established memories, so that familiarity with either a behavioral strategy or an environment can inform goal-directed learning. PMID:22323731

Ideal MHD stability and performance of ITER steady-state scenarios with ITBs

NASA Astrophysics Data System (ADS)

Poli, F. M.; Kessel, C. E.; Chance, M. S.; Jardin, S. C.; Manickam, J.

2012-06-01

Non-inductive steady-state scenarios on ITER will need to operate with internal transport barriers (ITBs) in order to reach adequate fusion gain at typical currents of 9 MA. The large pressure gradients at the location of the internal barrier are conducive to the development of ideal MHD instabilities that may limit the plasma performance and may lead to plasma disruptions. Fully non-inductive scenario simulations with five combinations of heating and current drive sources are presented in this work, with plasma currents in the range 7-10 MA. For each configuration the linear, ideal MHD stability is analysed for variations of the Greenwald fraction and of the pressure peaking factor around the operating point, aiming at defining an operational space for stable, steady-state operations at optimized performance. It is shown that plasmas with lower hybrid heating and current drive maintain the minimum safety factor above 1.5, which is desirable in steady-state operations to avoid neoclassical tearing modes. Operating with moderate ITBs at 2/3 of the minor radius, these plasmas have a minimum safety factor above 2, are ideal MHD stable and reach Q ≳ 5 operating above the ideal no-wall limit.

U.S. Geological Survey Standard Reference Sample Project: Performance Evaluation of Analytical Laboratories

USGS Publications Warehouse

Long, H. Keith; Daddow, Richard L.; Farrar, Jerry W.

1998-01-01

Since 1962, the U.S. Geological Survey (USGS) has operated the Standard Reference Sample Project to evaluate the performance of USGS, cooperator, and contractor analytical laboratories that analyze chemical constituents of environmental samples. The laboratories are evaluated by using performance evaluation samples, called Standard Reference Samples (SRSs). SRSs are submitted to laboratories semi-annually for round-robin laboratory performance comparison purposes. Currently, approximately 100 laboratories are evaluated for their analytical performance on six SRSs for inorganic and nutrient constituents. As part of the SRS Project, a surplus of homogeneous, stable SRSs is maintained for purchase by USGS offices and participating laboratories for use in continuing quality-assurance and quality-control activities. Statistical evaluation of the laboratories results provides information to compare the analytical performance of the laboratories and to determine possible analytical deficiences and problems. SRS results also provide information on the bias and variability of different analytical methods used in the SRS analyses.

Flood replenishment: a new method of processor control.

PubMed

Frank, E D; Gray, J E; Wilken, D A

1980-01-01

In mechanized radiographic film processors that process medium to low volumes of film, roll films, and those that process single-emulsion films from nuclear medicine scans, computed tomography, and ultrasound, it is difficult to maintain the developer solution at a stable processing level. We describe our experience using flood replenishment, which is a method in which developer replenisher containing starter solution is introduced in the processor at timed intervals, independent of the number of films being processed. By this process, a stable level of developer activity is maintained in a processor used to develop a medium to low volume of single-emulsion film.

Revisiting and Extending Interface Penalties for Multi-Domain Summation-by-Parts Operators

NASA Technical Reports Server (NTRS)

Carpenter, Mark H.; Nordstrom, Jan; Gottlieb, David

2007-01-01

General interface coupling conditions are presented for multi-domain collocation methods, which satisfy the summation-by-parts (SBP) spatial discretization convention. The combined interior/interface operators are proven to be L2 stable, pointwise stable, and conservative, while maintaining the underlying accuracy of the interior SBP operator. The new interface conditions resemble (and were motivated by) those used in the discontinuous Galerkin finite element community, and maintain many of the same properties. Extensive validation studies are presented using two classes of high-order SBP operators: 1) central finite difference, and 2) Legendre spectral collocation.

Visual attention and stability

PubMed Central

Mathôt, Sebastiaan; Theeuwes, Jan

2011-01-01

In the present review, we address the relationship between attention and visual stability. Even though with each eye, head and body movement the retinal image changes dramatically, we perceive the world as stable and are able to perform visually guided actions. However, visual stability is not as complete as introspection would lead us to believe. We attend to only a few items at a time and stability is maintained only for those items. There appear to be two distinct mechanisms underlying visual stability. The first is a passive mechanism: the visual system assumes the world to be stable, unless there is a clear discrepancy between the pre- and post-saccadic image of the region surrounding the saccade target. This is related to the pre-saccadic shift of attention, which allows for an accurate preview of the saccade target. The second is an active mechanism: information about attended objects is remapped within retinotopic maps to compensate for eye movements. The locus of attention itself, which is also characterized by localized retinotopic activity, is remapped as well. We conclude that visual attention is crucial in our perception of a stable world. PMID:21242140

An isopropanol-assisted fabrication strategy of pinhole-free perovskite films in air for efficient and stable planar perovskite solar cells

NASA Astrophysics Data System (ADS)

Ren, Ziqiu; Zhu, Menghua; Li, Xin; Dong, Cunku

2017-09-01

As a promising photovoltaic device, perovskite solar cells have attracted numerous attention in recent years, where forming a compact and pinhole-free perovskite film in air is of great importance. Herein, we evaluate highly efficient and air stable planar perovskite solar cells in air (relative humidity over 50%) with the modified two-step sequential deposition method by adjusting the CH3NH3I (MAI) concentrations and regulating the crystallization process of the perovskite film. The optimum MAI concentration is 60 mg mL-1 in isopropanol. With a planar structure of FTO/TiO2/MAPbI3/spiro-OMeTAD/Au, the efficient devices composed of compact and pinhole-free perovskite films are constructed in air, achieving a high efficiency of up to 15.10% and maintaining over 80% after 20 days storing without any encapsulation in air. With a facile fabrication process and high photovoltaic performance, this work represents a promising method for fabricating low-cost, highly efficient and stable photovoltaic device.

Stable olfactory sensory neuron in vivo physiology during normal aging.

PubMed

Kass, Marley D; Czarnecki, Lindsey A; McGann, John P

2018-05-08

Normal aging is associated with a number of smell impairments that are paralleled by age-dependent changes in the peripheral olfactory system, including decreases in olfactory sensory neurons (OSNs) and in the regenerative capacity of the epithelium. Thus, an age-dependent degradation of sensory input to the brain is one proposed mechanism for the loss of olfactory function in older populations. Here, we tested this hypothesis by performing in vivo optical neurophysiology in 6-, 12-, 18-, and 24-month-old mice. We visualized odor-evoked neurotransmitter release from populations of OSNs into olfactory bulb glomeruli, and found that these sensory inputs are actually quite stable during normal aging. Specifically, the magnitude and number of odor-evoked glomerular responses were comparable across all ages, and there was no effect of age on the sensitivity of OSN responses to odors or on the neural discriminability of different sensory maps. These results suggest that the brain's olfactory bulbs do not receive deteriorated input during aging and that local bulbar circuitry might adapt to maintain stable nerve input. Copyright © 2018 Elsevier Inc. All rights reserved.

Frequency-Dependent Selection: The High Potential for Permanent Genetic Variation in the Diallelic, Pairwise Interaction Model

PubMed Central

Asmussen, M. A.; Basnayake, E.

1990-01-01

A detailed analytic and numerical study is made of the potential for permanent genetic variation in frequency-dependent models based on pairwise interactions among genotypes at a single diallelic locus. The full equilibrium structure and qualitative gene-frequency dynamics are derived analytically for a symmetric model, in which pairwise fitnesses are chiefly determined by the genetic similarity of the individuals involved. This is supplemented by an extensive numerical investigation of the general model, the symmetric model, and nine other special cases. Together the results show that there is a high potential for permanent genetic diversity in the pairwise interaction model, and provide insight into the extent to which various forms of genotypic interactions enhance or reduce this potential. Technically, although two stable polymorphic equilibria are possible, the increased likelihood of maintaining both alleles, and the poor performance of protected polymorphism conditions as a measure of this likelihood, are primarily due to a greater variety and frequency of equilibrium patterns with one stable polymorphic equilibrium, in conjunction with a disproportionately large domain of attraction for stable internal equilibria. PMID:2341034

Longitudinal changes in quantitative and qualitative indicators of word and story recall in young-old and old-old adults.

PubMed

Small, B J; Dixon, R A; Hultsch, D F; Hertzog, C

1999-03-01

The present study examined longitudinal changes in quantitative and qualitative measures of episodic memory. The sample, taken from the Victoria Longitudinal Study, consisted of 158 young-old adults (initially 55 to 70 years old) and 84 old-old adults (initially 71 to 86 years old) who were tested three times over six years. Average word and text recall, as well as five indicators of qualitative aspects of word recall (e.g., number of categories recalled) and one indicator of structure of text recall (i.e., levels of information) were used. For word recall, although both age groups exhibited negative longitudinal changes in quantitative performance, overall qualitative performance was generally stable. Two qualitative indicators (number of categories and intrusions) showed modest decline and one (organization at recall) showed improvement. Results for overall text recall showed significant performance increments for the young-old group, whereas the old-old group exhibited slight declines in overall performance. Analyses of qualitative measures showed stable structure of hierarchical recall, with the old-old being impaired at all levels of detail in the stories. Overall results suggest that some underlying structural characteristics of word and text recall may be maintained into late life even when significant overall decline is observed.

A Temperature-Stable Cryo-System for High-Temperature Superconducting MR In-Vivo Imaging

PubMed Central

Lin, In-Tsang; Yang, Hong-Chang; Chen, Jyh-Horng

2013-01-01

To perform a rat experiment using a high-temperature superconducting (HTS) surface resonator, a cryostat is essential to maintain the rat's temperature. In this work, a compact temperature-stable HTS cryo-system, keeping animal rectal temperature at 37.4°C for more than 3 hours, was successfully developed. With this HTS cryo-system, a 40-mm-diameter Bi2Sr2Ca2Cu3Ox (Bi-2223) surface resonator at 77 K was demonstrated in a 3-Tesla MRI system. The proton resonant frequency (PRF) method was employed to monitor the rat's temperature. Moreover, the capacity of MR thermometry in the HTS experiments was evaluated by correlating with data from independent fiber-optic sensor temperature measurements. The PRF thermal coefficient was derived as 0.03 rad/°C and the temperature-monitoring architecture can be implemented to upgrade the quality and safety in HTS experiments. The signal-to-noise ratio (SNR) of the HTS surface resonator at 77 K was higher than that of a professionally made copper surface resonator at 300 K, which has the same geometry, by a 3.79-fold SNR gain. Furthermore, the temperature-stable HTS cryo-system we developed can obtain stable SNR gain in every scan. A temperature-stable HTS cryo-system with an external air-blowing circulation system is demonstrated. PMID:23637936

Lie group model neuromorphic geometric engine for real-time terrain reconstruction from stereoscopic aerial photos

NASA Astrophysics Data System (ADS)

Tsao, Thomas R.; Tsao, Doris

1997-04-01

In the 1980's, neurobiologist suggested a simple mechanism in primate visual cortex for maintaining a stable and invariant representation of a moving object. The receptive field of visual neurons has real-time transforms in response to motion, to maintain a stable representation. When the visual stimulus is changed due to motion, the geometric transform of the stimulus triggers a dual transform of the receptive field. This dual transform in the receptive fields compensates geometric variation in the stimulus. This process can be modelled using a Lie group method. The massive array of affine parameter sensing circuits will function as a smart sensor tightly coupled to the passive imaging sensor (retina). Neural geometric engine is a neuromorphic computing device simulating our Lie group model of spatial perception of primate's primal visual cortex. We have developed the computer simulation and experimented on realistic and synthetic image data, and performed a preliminary research of using analog VLSI technology for implementation of the neural geometric engine. We have benchmark tested on DMA's terrain data with their result and have built an analog integrated circuit to verify the computational structure of the engine. When fully implemented on ANALOG VLSI chip, we will be able to accurately reconstruct a 3D terrain surface in real-time from stereoscopic imagery.

Characterization of dopamine releasable and reserve pools in Drosophila larvae using ATP/P2X2-mediated stimulation

PubMed Central

Xiao, Ning; Venton, B. Jill

2015-01-01

Dopaminergic signaling pathways are conserved between mammals and Drosophila, but the factors important for maintaining the functional pool of synaptic dopamine are not fully understood in Drosophila. In this study, we characterized the releasable and reserve dopamine pools in Drosophila larvae using ATP/ P2X2-mediated stimulation. Dopamine release was stable with stimulations performed at least every 5 min but decayed with stimulations performed 2 min apart or less, indicating the replenishment of the releasable pool occurred on a time scale between 2 and 5 min. Dopamine synthesis or uptake were pharmacologically inhibited with 3-iodotyrosine and cocaine, respectively, to evaluate their contributions to maintaining the releasable dopamine pool. We found that both synthesis and uptake were needed to maintain the releasable dopamine pool, with synthesis playing a major part in long-term replenishment and uptake being more important for short-term replenishment. These effects of synthesis and uptake on different time scales in Drosophila are analogous to mammals. However, unlike in mammals, cocaine did not activate a reserve pool of dopamine in Drosophila when using P2X2 stimulations. Our study shows that both synthesis and uptake replenish the releasable pool, providing a better understanding of dopamine regulation in Drosophila. PMID:25951875

Evolutionary performance of zero-determinant strategies in multiplayer games.

PubMed

Hilbe, Christian; Wu, Bin; Traulsen, Arne; Nowak, Martin A

2015-06-07

Repetition is one of the key mechanisms to maintain cooperation. In long-term relationships, in which individuals can react to their peers׳ past actions, evolution can promote cooperative strategies that would not be stable in one-shot encounters. The iterated prisoner׳s dilemma illustrates the power of repetition. Many of the key strategies for this game, such as ALLD, ALLC, Tit-for-Tat, or generous Tit-for-Tat, share a common property: players using these strategies enforce a linear relationship between their own payoff and their co-player׳s payoff. Such strategies have been termed zero-determinant (ZD). Recently, it was shown that ZD strategies also exist for multiplayer social dilemmas, and here we explore their evolutionary performance. For small group sizes, ZD strategies play a similar role as for the repeated prisoner׳s dilemma: extortionate ZD strategies are critical for the emergence of cooperation, whereas generous ZD strategies are important to maintain cooperation. In large groups, however, generous strategies tend to become unstable and selfish behaviors gain the upper hand. Our results suggest that repeated interactions alone are not sufficient to maintain large-scale cooperation. Instead, large groups require further mechanisms to sustain cooperation, such as the formation of alliances or institutions, or additional pairwise interactions between group members. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

Using Reinforcement Learning to Provide Stable Brain-Machine Interface Control Despite Neural Input Reorganization

PubMed Central

Pohlmeyer, Eric A.; Mahmoudi, Babak; Geng, Shijia; Prins, Noeline W.; Sanchez, Justin C.

2014-01-01

Brain-machine interface (BMI) systems give users direct neural control of robotic, communication, or functional electrical stimulation systems. As BMI systems begin transitioning from laboratory settings into activities of daily living, an important goal is to develop neural decoding algorithms that can be calibrated with a minimal burden on the user, provide stable control for long periods of time, and can be responsive to fluctuations in the decoder’s neural input space (e.g. neurons appearing or being lost amongst electrode recordings). These are significant challenges for static neural decoding algorithms that assume stationary input/output relationships. Here we use an actor-critic reinforcement learning architecture to provide an adaptive BMI controller that can successfully adapt to dramatic neural reorganizations, can maintain its performance over long time periods, and which does not require the user to produce specific kinetic or kinematic activities to calibrate the BMI. Two marmoset monkeys used the Reinforcement Learning BMI (RLBMI) to successfully control a robotic arm during a two-target reaching task. The RLBMI was initialized using random initial conditions, and it quickly learned to control the robot from brain states using only a binary evaluative feedback regarding whether previously chosen robot actions were good or bad. The RLBMI was able to maintain control over the system throughout sessions spanning multiple weeks. Furthermore, the RLBMI was able to quickly adapt and maintain control of the robot despite dramatic perturbations to the neural inputs, including a series of tests in which the neuron input space was deliberately halved or doubled. PMID:24498055

Cognitively Elite, Cognitively Normal, and Cognitively Impaired Aging: Neurocognitive Status and Stability Moderate Memory Performance

PubMed Central

Dixon, Roger A.; de Frias, Cindy M.

2014-01-01

Objective Although recent theories of brain and cognitive aging distinguish among normal, exceptional, and impaired groups, further empirical evidence is required. We adapted and applied standard procedures for classifying groups of cognitively impaired (CI) and cognitively normal (CN) older adults to a third classification, cognitively healthy, exceptional, or elite (CE) aging. We then examined concurrent and two-wave longitudinal performance on composite variables of episodic, semantic, and working memory. Method We began with a two-wave source sample from the Victoria Longitudinal Study (VLS) (source n=570; baseline age=53–90 years). The goals were to: (a) apply standard and objective classification procedures to discriminate three cognitive status groups, (b) conduct baseline comparisons of memory performance, (c) develop two-wave status stability and change subgroups, and (d) compare of stability subgroup differences in memory performance and change. Results As expected, the CE group performed best on all three memory composites. Similarly, expected status stability effects were observed: (a) stable CE and CN groups performed memory tasks better than their unstable counterparts and (b) stable (and chronic) CI group performed worse than its unstable (variable) counterpart. These stability group differences were maintained over two waves. Conclusion New data validate the expectations that (a) objective clinical classification procedures for cognitive impairment can be adapted for detecting cognitively advantaged older adults and (b) performance in three memory systems is predictably related to the tripartite classification. PMID:24742143

France's Administrative Tertiary: Stable Numbers for Occupations in Flux.

ERIC Educational Resources Information Center

Liaroutzos, Olivier; Meriot, Sylvie-Anne

1995-01-01

During the past decade, the number of jobs in France's administrative service sector has remained stable. General administrative work has become more infrequent; however, the basic occupations of secretary and accountancy have been maintained. Although the number of typists has declined, the number of "secretarial" jobs has increased…

The impact of phosphate-balanced crystalloid infusion on acid-base homeostasis (PALANCE study): study protocol for a randomized controlled trial.

PubMed

Pagel, Judith-Irina; Hulde, Nikolai; Kammerer, Tobias; Schwarz, Michaela; Chappell, Daniel; Burges, Alexander; Hofmann-Kiefer, Klaus; Rehm, Markus

2017-07-10

This study aims to investigate the effects of a modified, balanced crystalloid including phosphate in a perioperative setting in order to maintain a stable electrolyte and acid-base homeostasis in the patient. This is a single-centre, open-label, randomized controlled trial involving two parallel groups of female patients comparing a perioperative infusion regime with sodium glycerophosphate and Jonosteril® (treatment group) or Jonosteril® (comparator) alone. The primary endpoint is to maintain a stable concentration of weak acids [A - ] according to the Stewart approach of acid-base balance. Secondary endpoints are measurement of serum phosphate levels, other acid-base parameters such as the strong ion difference (SID), the onset and severity of postoperative nausea and vomiting (PONV), electrolyte levels and their excretion in the urine, monitoring of renal function and glycocalyx components, haemodynamics, amounts of catecholamines and other vasopressors used and the safety of the infusion regime. Perioperative fluid replacement with the use of currently available crystalloid preparations still fail to maintain a stable acid-base balance and experts agree that common balanced solutions are still not ideal. This study aims to investigate the effectivity and safety of a new crystalloid solution by adding sodium glycerophosphate to a standardized crystalloid preparation in order to maintain a balanced perioperative acid-base homeostasis. EudraCT number 201002422520 . Registered on 30 November 2010.

More than meets the eye: the role of language in binding and maintaining feature conjunctions.

PubMed

Dessalegn, Banchiamlack; Landau, Barbara

2008-02-01

We investigated the effects of language on vision by focusing on a well-known problem: the binding and maintenance of color-location conjunctions. Four-year-olds performed a task in which they saw a target (e.g., a split square, red on the left and green on the right) followed by a brief delay and then were asked to find the target in an array including the target, its reflection (e.g., red on the right and green on the left), and a square with a different geometric split. Errors were overwhelmingly reflections. This finding shows that the children failed to maintain color-location conjunctions. Performance improved when targets were accompanied by sentences specifying color and direction (e.g., "the red is on the left"), but not when the conjunction was highlighted using a nonlinguistic cue (e.g., flashing, pointing, changes in size), nor when sentences specified a nondirectional relationship (e.g., "the red is touching the green"). The relation between children's matching performance and their long-term knowledge of directional terms suggests two distinct mechanisms by which language can temporarily bridge delays, providing more stable representations.

Stable metal-organic frameworks containing single-molecule traps for enzyme encapsulation.

PubMed

Feng, Dawei; Liu, Tian-Fu; Su, Jie; Bosch, Mathieu; Wei, Zhangwen; Wan, Wei; Yuan, Daqiang; Chen, Ying-Pin; Wang, Xuan; Wang, Kecheng; Lian, Xizhen; Gu, Zhi-Yuan; Park, Jihye; Zou, Xiaodong; Zhou, Hong-Cai

2015-01-19

Enzymatic catalytic processes possess great potential in chemical manufacturing, including pharmaceuticals, fuel production and food processing. However, the engineering of enzymes is severely hampered due to their low operational stability and difficulty of reuse. Here, we develop a series of stable metal-organic frameworks with rationally designed ultra-large mesoporous cages as single-molecule traps (SMTs) for enzyme encapsulation. With a high concentration of mesoporous cages as SMTs, PCN-333(Al) encapsulates three enzymes with record-high loadings and recyclability. Immobilized enzymes that most likely undergo single-enzyme encapsulation (SEE) show smaller Km than free enzymes while maintaining comparable catalytic efficiency. Under harsh conditions, the enzyme in SEE exhibits better performance than free enzyme, showing the effectiveness of SEE in preventing enzyme aggregation or denaturation. With extraordinarily large pore size and excellent chemical stability, PCN-333 may be of interest not only for enzyme encapsulation, but also for entrapment of other nanoscaled functional moieties.

Stable metal-organic frameworks containing single-molecule traps for enzyme encapsulation

NASA Astrophysics Data System (ADS)

Feng, Dawei; Liu, Tian-Fu; Su, Jie; Bosch, Mathieu; Wei, Zhangwen; Wan, Wei; Yuan, Daqiang; Chen, Ying-Pin; Wang, Xuan; Wang, Kecheng; Lian, Xizhen; Gu, Zhi-Yuan; Park, Jihye; Zou, Xiaodong; Zhou, Hong-Cai

2015-01-01

Enzymatic catalytic processes possess great potential in chemical manufacturing, including pharmaceuticals, fuel production and food processing. However, the engineering of enzymes is severely hampered due to their low operational stability and difficulty of reuse. Here, we develop a series of stable metal-organic frameworks with rationally designed ultra-large mesoporous cages as single-molecule traps (SMTs) for enzyme encapsulation. With a high concentration of mesoporous cages as SMTs, PCN-333(Al) encapsulates three enzymes with record-high loadings and recyclability. Immobilized enzymes that most likely undergo single-enzyme encapsulation (SEE) show smaller Km than free enzymes while maintaining comparable catalytic efficiency. Under harsh conditions, the enzyme in SEE exhibits better performance than free enzyme, showing the effectiveness of SEE in preventing enzyme aggregation or denaturation. With extraordinarily large pore size and excellent chemical stability, PCN-333 may be of interest not only for enzyme encapsulation, but also for entrapment of other nanoscaled functional moieties.

Enhancing soil begins with soil biology and a stable soil microclimate

USDA-ARS?s Scientific Manuscript database

Protection of the soil resource from erosion requires reducing the surface impact from raindrop energy and maintaining soil structure and stability to allow more efficient infiltration of water into the soil column. These two processes are linked with practices associated with enhancing and maintain...

Recurrent Neural Networks With Auxiliary Memory Units.

PubMed

Wang, Jianyong; Zhang, Lei; Guo, Quan; Yi, Zhang

2018-05-01

Memory is one of the most important mechanisms in recurrent neural networks (RNNs) learning. It plays a crucial role in practical applications, such as sequence learning. With a good memory mechanism, long term history can be fused with current information, and can thus improve RNNs learning. Developing a suitable memory mechanism is always desirable in the field of RNNs. This paper proposes a novel memory mechanism for RNNs. The main contributions of this paper are: 1) an auxiliary memory unit (AMU) is proposed, which results in a new special RNN model (AMU-RNN), separating the memory and output explicitly and 2) an efficient learning algorithm is developed by employing the technique of error flow truncation. The proposed AMU-RNN model, together with the developed learning algorithm, can learn and maintain stable memory over a long time range. This method overcomes both the learning conflict problem and gradient vanishing problem. Unlike the traditional method, which mixes the memory and output with a single neuron in a recurrent unit, the AMU provides an auxiliary memory neuron to maintain memory in particular. By separating the memory and output in a recurrent unit, the problem of learning conflicts can be eliminated easily. Moreover, by using the technique of error flow truncation, each auxiliary memory neuron ensures constant error flow during the learning process. The experiments demonstrate good performance of the proposed AMU-RNNs and the developed learning algorithm. The method exhibits quite efficient learning performance with stable convergence in the AMU-RNN learning and outperforms the state-of-the-art RNN models in sequence generation and sequence classification tasks.

Simultaneous Independent Control of Tool Axial Force and Temperature in Friction Stir Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ross, Kenneth A.; Grant, Glenn J.; Darsell, Jens T.

Maintaining consistent tool depth relative to the part surface is a critical requirement for many Friction stir processing (FSP) applications. Force control is often used with the goal of obtaining a constant weld depth. When force control is used, if weld temperature decreases, flow stress increases and the tool is pushed up. If weld temperature increases, flow stress decreases and the tool dives. These variations in tool depth and weld temperature cause various types of weld defects. Robust temperature control for FSP maintains a commanded temperature through control of the spindle axis only. Robust temperature control and force control aremore » completely decoupled in control logic and machine motion. This results in stable temperature, force and tool depth despite the presence of geometric and thermal disturbances. Performance of this control method is presented for various weld paths and alloy systems.« less

Use of an elastic transarticular external fixator construct for immobilization of the elbow joint.

PubMed

Vedrine, Bertrand

2017-04-01

Transarticular external skeletal fixation usually involves rigid bars that result in a stable but stiff joint. This study describes the technique and the outcome of an elastic transarticular external fixator (ETEF) applied to the elbow joint. Four cases of elbow luxation with collateral ligament injuries were managed with closed reduction and application of an ETEF to maintain the reduction. A triceps tendon avulsion was surgically managed before applying an ETEF. The clinical outcome was considered excellent in 2 cats, good in 2 dogs (1 elbow luxation and the avulsion of the triceps tendon), and poor in 1 dog presented for elbow luxation and a permanent neurological defect. The procedure was rapid, easy to perform, and inexpensive. All animals except the one with a neurological defect had an early return to weight bearing. This method maintains extension of the joint while permitting its motion thereby promoting rehabilitation.

Use of an elastic transarticular external fixator construct for immobilization of the elbow joint

PubMed Central

Vedrine, Bertrand

2017-01-01

Transarticular external skeletal fixation usually involves rigid bars that result in a stable but stiff joint. This study describes the technique and the outcome of an elastic transarticular external fixator (ETEF) applied to the elbow joint. Four cases of elbow luxation with collateral ligament injuries were managed with closed reduction and application of an ETEF to maintain the reduction. A triceps tendon avulsion was surgically managed before applying an ETEF. The clinical outcome was considered excellent in 2 cats, good in 2 dogs (1 elbow luxation and the avulsion of the triceps tendon), and poor in 1 dog presented for elbow luxation and a permanent neurological defect. The procedure was rapid, easy to perform, and inexpensive. All animals except the one with a neurological defect had an early return to weight bearing. This method maintains extension of the joint while permitting its motion thereby promoting rehabilitation. PMID:28373726

Switchable single-longitudinal-mode dual-wavelength erbium-doped fiber laser based on one polarization-maintaining fiber Bragg grating incorporating saturable absorber

NASA Astrophysics Data System (ADS)

Feng, Suchun; Xu, Ou; Lu, Shaohua; Chen, Ming; Jian, Shuisheng

2009-08-01

Switchable single-longitudinal-mode (SLM) dual-wavelength erbium-doped fiber laser at room temperature is demonstrated. One fiber Bragg grating (FBG) directly written in a polarization-maintaining and photosensitive erbiumdoped fiber (PMPEDF) as the wavelength-selective component is used in a linear laser cavity. Due to the polarization hole burning (PHB) enhanced by the polarization-maintaining fiber Bragg grating (PMFBG), the laser can be designed to operate in stable dual-wavelength or wavelength-switching modes with a wavelength spacing of 0.202 nm by adjusting a polarization controller (PC). The stable SLM operation is guaranteed by a saturable absorber (SA). The optical signal-tonoise ratio (OSNR) of the laser is over 40 dB. The amplitude variation in nearly one and half an hour is less than 0.5 dB for both wavelengths.

Long-Lived Near-Earth Asteroid 2013 RB6

NASA Astrophysics Data System (ADS)

Emel'yanenko, V. V.; Emel'yanenko, N. Yu.

2018-01-01

The search for asteroids that maintain stable motion in the zone between the Earth and Mars has been performed. The near-Earth object 2013 RB6, which has avoided close encounters with the planets for a long period of time, has been found. Integration of the equations of motion of the object shows that its dynamical lifetime in the zone between the Earth and Mars significantly exceeds 100 Myr. 2013 RB6 moves away from orbital resonances with the planets, but is in the secular resonance ν5. Solving the question of its origin requires further observations.

Organic content influences sediment microbial fuel cell performance and community structure.

PubMed

Zhao, Qing; Li, Ruying; Ji, Min; Ren, Zhiyong Jason

2016-11-01

This study constructed sediment microbial fuel cells (SMFCs) with different organic loadings without the amendment of external substrates, and it investigated how such variation affects electricity generation and microbial community structure. Results found sediment characteristics significantly influenced SMFC performance and appropriate organic content is important to maintain stable power outputs. SMFCs with loss of ignition (LOI) of 5% showed the most reliable performance in this study, while high organic content (LOI 10-16%) led to higher but very unstable voltage output because of biogas accumulation and worm activities. SMFCs with low organic content (1-3%) showed low power output. Different bacterial communities were found in SMFCs shown various power generation performance even those with similar organic contents. Thermodesulfovibrionaceae was found closely related to the system startup and Desulfobulbaceae showed great abundance in SMFCs with high power production. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Body weight change and health outcomes in middle-aged men--a prospective study results].

PubMed

Kaleta, Dorota; Kwaśniewska, Magdalena; Bednarek-Gejo, Anna; Dziankowska-Zaborszczyk, Elzbieta; Jegier, Anna; Kostka, Tomasz; Drygas, Wojciech K

2005-01-01

In recent years more attention is paid to the role of body weight change and cardiovascular disease risk. The aim of the study was to evaluate correlation between body weight change and risk of ischaemic heart disease (IHD) and selected cardiovascular disease risk in middle-aged male during long-term surveillance. The study was conducted among group of healthy male volunteers (n=189) aged 30-49 years at baseline. Prevalence of disease due to cardiovascular causes was ascertained in study participants during an average follow-up of 17.7 +/- 4.4 years. Changes in weight were classified in three categories: stable weight (+/- 5 kg), weight gain (>5 kg) or weight loss (>5 kg). Logistic regression analysis was performed to study the correlation between weight change and Relative Risk (RR) of cardiovascular disease in the examined subjects. All analyses were adjusted for age, smoking and level of leisure-time physical activity. In this study 48.4% men maintained weight, 5.9% lowered weight and 45.7% gained weight. Ischaemic heart disease was diagnosed in 12.2% of men, including non fatal myocardial infarction in 5.3%, hypertension in 40.7%, and hyperchoesterolaemia in 62.4%, respectively. Among participants with weight gain of more than 5 kg total cardiovascular disease risk was 4 times higher (adjusted RR=4.07, 95% CI, 1.33-12.44), ischaemic heart disease 3 times higher (adjusted RR=3.27, 95% CI, 1.17-9.17), and hypercholesterolaemia 2 times higher (adjusted RR=2.15, 95% CI, 1.09-4.24) in comparison with those with stable weight. This study results suggests that maintaining stable weight during adulthood can be effective strategy for lowering cardiovascular disease risk.

Passive levitation in alternating magnetic fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romero, Louis; Christenson, Todd; Aronson, Eugene A.

2010-09-14

Stable levitation of an object in an alternating magnetic field can be achieved by eliminating coupling between the rotational and translational forces acting on the object. Stable levitation can also be achieved by varying the coupling between the rotational and translational forces acting on the object, while maintaining one or more of the rotational and translational forces steady in time.

Passive levitation in alternating magnetic fields

DOE Office of Scientific and Technical Information (OSTI.GOV)

Romero, Louis; Christenson, Todd; Aronson, Eugene A

2009-06-16

Stable levitation of an object in an alternating magnetic field can be achieved by eliminating coupling between the rotational and translational forces acting on the object. Stable levitation can also be achieved by varying the coupling between the rotational and translational forces acting on the object, while maintaining one or more of the rotational and translational forces steady in time.

Efficacy of knightstick traps and sticky wraps for attraction and capture of stable flies (Stomoxys calcitrans)

USDA-ARS?s Scientific Manuscript database

The stable fly, Stomoxys calcitrans, is known as a noxious pest of livestock, particularly cattle, in many countries of the world. However, this blood-feeding fly can also pestiferous around pets and companion animals maintained outdoors. Two groups of animals, dogs and horses, are major hosts for s...

Free-anchored Nb2O5@graphene networks for ultrafast-stable lithium storage.

PubMed

Deng, Qinglin; Li, Mengjiao; Wang, Junyong; Jiang, Kai; Hu, Zhigao; Chu, Junhao

2018-05-04

Orthorhombic Nb 2 O 5 (T-Nb 2 O 5 ) has structural merit but poor electrical conductivity, limiting their applications in energy storage. Although graphene is frequently adopted to effectively improve its electrochemical properties, the ordinary modified methods cannot meet the growing demands for high-performance. Here, we demonstrate that different graphene modified routes play a vital role in affecting the electrochemical performances of T-Nb 2 O 5 . By only manual shaking within one minute, Nb 2 O 5 nano-particles can be rapidly adsorbed onto graphene, then the free-anchored T-Nb 2 O 5 @graphene three-dimensional networks can be successfully prepared based on hydrogel method. As for the application in lithium-ion batteries, it performs outstanding rate character (129 mA h g -1 (25C rate), 110 mA h g -1 (50C rate) and 90 mA h g -1 (100C rate), correspond to 79%, 67% and 55% capacity of 0.5C rate, respectively) and excellent long-term cycling feature (∼70% capacity retention after 20000 cycles). Moreover, it still maintains similar ultrafast-stable lithium storage performances when Cu foil is substituted by Al foil as current collector. In addition, relevant kinetics mechanisms are also expounded. This work provides a versatile strategy for the preparation of graphene modified Nb 2 O 5 or other types of nanoparticles.

Free-anchored Nb2O5@graphene networks for ultrafast-stable lithium storage

NASA Astrophysics Data System (ADS)

Deng, Qinglin; Li, Mengjiao; Wang, Junyong; Jiang, Kai; Hu, Zhigao; Chu, Junhao

2018-05-01

Orthorhombic Nb2O5 (T-Nb2O5) has structural merit but poor electrical conductivity, limiting their applications in energy storage. Although graphene is frequently adopted to effectively improve its electrochemical properties, the ordinary modified methods cannot meet the growing demands for high-performance. Here, we demonstrate that different graphene modified routes play a vital role in affecting the electrochemical performances of T-Nb2O5. By only manual shaking within one minute, Nb2O5 nano-particles can be rapidly adsorbed onto graphene, then the free-anchored T-Nb2O5@graphene three-dimensional networks can be successfully prepared based on hydrogel method. As for the application in lithium-ion batteries, it performs outstanding rate character (129 mA h g-1 (25C rate), 110 mA h g-1 (50C rate) and 90 mA h g-1 (100C rate), correspond to 79%, 67% and 55% capacity of 0.5C rate, respectively) and excellent long-term cycling feature (˜70% capacity retention after 20000 cycles). Moreover, it still maintains similar ultrafast-stable lithium storage performances when Cu foil is substituted by Al foil as current collector. In addition, relevant kinetics mechanisms are also expounded. This work provides a versatile strategy for the preparation of graphene modified Nb2O5 or other types of nanoparticles.

Cell culture chamber with gas supply for prolonged recording of human neuronal cells on microelectrode array.

PubMed

Kreutzer, Joose; Ylä-Outinen, Laura; Mäki, Antti-Juhana; Ristola, Mervi; Narkilahti, Susanna; Kallio, Pasi

2017-03-15

Typically, live cell analyses are performed outside an incubator in an ambient air, where the lack of sufficient CO 2 supply results in a fast change of pH and the high evaporation causes concentration drifts in the culture medium. That limits the experiment time for tens of minutes. In many applications, e.g. in neurotoxicity studies, a prolonged measurement of extracellular activity is, however, essential. We demonstrate a simple cell culture chamber that enables stable culture conditions during prolonged extracellular recordings on a microelectrode array (MEA) outside an incubator. The proposed chamber consists of a gas permeable silicone structure that enables gas transfer into the chamber. We show that the culture chamber supports the growth of the human embryonic stem cell (hESC)-derived neurons both inside and outside an incubator. The structure provides very low evaporation, stable pH and osmolarity, and maintains strong signaling of hESC-derived neuronal networks over three-day MEA experiments. Existing systems are typically complex including continuous perfusion of medium or relatively large amount of gas to supply. The proposed chamber requires only a supply of very low flow rate (1.5ml/min) of non-humidified 5% CO 2 gas. Utilizing dry gas supply makes the proposed chamber simple to use. Using the proposed culture structure on top of MEA, we can maintain hESC-derived neural networks over three days outside an incubator. Technically, the structure requires very low flow rate of dry gas supporting, however, low evaporation and maintaining the pH of the culture. Copyright © 2017 Elsevier B.V. All rights reserved.

Aquatic Exercise Training is Effective in Maintaining Exercise Performance in Trained Heart Failure Patients: A Randomised Crossover Pilot Trial.

PubMed

Adsett, Julie; Morris, Norman; Kuys, Suzanne; Hwang, Rita; Mullins, Robert; Khatun, Mohsina; Paratz, Jennifer; Mudge, Alison

2017-06-01

Providing flexible models and a variety of exercise options are fundamental to supporting long-term exercise participation for patients with heart failure (HF). The aim of this pilot study was to determine the feasibility and efficacy of aquatic exercise training during a maintenance phase for a clinical heart failure population. In this 2 x 2 crossover design trial, individuals who had previously completed HF rehabilitation were randomised into either a land-based or aquatic training program once per week for six weeks, after which time they changed to the alternate exercise training protocol for an additional six weeks. Six-minute walk test (6MWT), grip strength, walk speed, and measures of balance were compared for the two training protocols. Fifty-one participants (43 males, mean age 69.2 yrs) contributed data for the analysis. Both groups maintained function during the follow-up period, however improvements in 6MWT were greater in the land-based training group (95% CI: 0.7, 22.5; p=0.038), by a mean difference of 10.8 metres. No significant difference was observed for other parameters when the two training protocols were compared. Attending an aquatic exercise program once per week is feasible for patients with stable HF and may provide a suitable option to maintain functional performance in select patients. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

Correlation between cerebral hemodynamic and perfusion pressure changes in non-human primates

NASA Astrophysics Data System (ADS)

Ruesch, A.; Smith, M. A.; Wollstein, G.; Sigal, I. A.; Nelson, S.; Kainerstorfer, J. M.

2017-02-01

The mechanism that maintains a stable blood flow in the brain despite changes in cerebral perfusion pressure (CPP), and therefore guaranties a constant supply of oxygen and nutrients to the neurons, is known as cerebral auto-regulation (CA). In a certain range of CPP, blood flow is mediated by a vasomotor adjustment in vascular resistance through dilation of blood vessels. CA is known to be impaired in diseases like traumatic brain injury, Parkinson's disease, stroke, hydrocephalus and others. If CA is impaired, blood flow and pressure changes are coupled and thee oxygen supply might be unstable. Lassen's blood flow auto-regulation curve describes this mechanism, where a plateau of stable blood flow in a specific range of CPP corresponds to intact auto-regulation. Knowing the limits of this plateau and maintaining CPP within these limits can improve patient outcome. Since CPP is influenced by both intracranial pressure and arterial blood pressure, long term changes in either can lead to auto-regulation impairment. Non-invasive methods for monitoring blood flow auto-regulation are therefore needed. We propose too use Near infrared spectroscopy (NIRS) too fill this need. NIRS is an optical technique, which measures microvascular changes in cerebral hemoglobin concentration. We performed experiments on non-human primates during exsanguination to demonstrate that thee limits of blood flow auto-regulation can be accessed with NIRS.

Employment and professional outcomes in 803 patients undergoing bariatric surgery in a French reference center for obesity.

PubMed

Durand-Moreau, Q; Gautier, A; Bécouarn, G; Topart, P; Rodien, P; Sallé, A

2015-04-01

Very few studies have been performed on small populations about the links between employment and bariatric surgery. To determine if rates of employment are increased among patients who have undergone bariatric surgery, to assess their post-operative health consequences (post-prandial weakness, diarrhea), and patients' ability to maintain post-operative advice (ie, 30 minutes of daily physical activity, 6 small meals daily) compared to non-employed post-surgical patients. This cross-sectional study was performed in the Regional Reference Centre for Obesity, which is a partnership between the University Hospital and a clinic in Angers, France during 2012 using a self-administrated questionnaire completed by patients hospitalized for post-operative follow-ups after bariatric surgery. Issues investigated were their professional situation before and after the surgery, compliancy to post-operative advice, and any postoperative side effects. Employment rates were 64.4% before and 64.7% after the surgery (p=0.94). Of these, 30.6% maintained 30 minutes of daily physical activity vs. 41.0% of non-workers (p=0.02). 50.5% of employed patients and 57.3% of non-workers maintained 6 small meals a day after surgery (p=0.09). 8% of working patients reported post-prandial weaknesses and 8% reported diarrhea that caused problems at work. Employment rate remained stable after surgery. Having a job seemed to be an obstacle to managing 30 minutes of daily exercise, especially among women, but not maintaining 6 small meals a day. Therefore, working environment needs to be assessed to improve job quality and retention for patients who have undergone bariatric surgery.

Highly efficient and stable white organic light emitting diode base on double recombination zones of phosphorescent blue/orange emitters.

PubMed

Lee, Seok Jae; Koo, Ja Ryong; Lim, Dong Hwan; Park, Hye Rim; Kim, Young Kwan; Ha, Yunkyoung

2011-08-01

We demonstrated efficient and stable white phosphorescent organic light-emitting diodes (OLEDs) with double-emitting layers (D-EMLs), which were comprised of two emissive layers with a hole transport-type host of N,N'-dicarbazolyl-3,5-benzene (mCP) and a electron transport-type host of 2,2',2"-(1,3,5-benzenetryl)tris(1-phenyl)-1H-benzimidazol (TPBi) with blue/orange emitters, respectively. We fabricated two type white devices with single emitting layer (S-EML) and D-EML of orange emitter, maintaining double recombination zone of blue emitter. In addition, the device architecture was developed to confine excitons inside the D-EMLs and to manage triplet excitons by controlling the charge injection. As a result, light-emitting performances of white OLED with D-EMLs were improved and showed the steady CIE coordinates compared to that with S-EML of orange emitter, which demonstrated the maximum luminous efficiency and external quantum efficiency were 21.38 cd/A and 11.09%. It also showed the stable white emission with CIE(x,y) coordinates from (x = 0.36, y = 0.37) at 6 V to (x = 0.33, y = 0.38) at 12 V.

High-Q Wafer Level Package Based on Modified Tri-Layer Anodic Bonding and High Performance Getter and Its Evaluation for Micro Resonant Pressure Sensor.

PubMed

Wang, Liying; Du, Xiaohui; Wang, Lingyun; Xu, Zhanhao; Zhang, Chenying; Gu, Dandan

2017-03-16

In order to achieve and maintain a high quality factor (high-Q) for the micro resonant pressure sensor, this paper presents a new wafer level package by adopting cross-layer anodic bonding technique of the glass/silicon/silica (GSS) stackable structure and integrated Ti getter. A double-layer structure similar to a silicon-on-insulator (SOI) wafer is formed after the resonant layer and the pressure-sensitive layer are bonded by silicon direct bonding (SDB). In order to form good bonding quality between the pressure-sensitive layer and the glass cap layer, the cross-layer anodic bonding technique is proposed for vacuum package by sputtering Aluminum (Al) on the combination wafer of the pressure-sensitive layer and the resonant layer to achieve electrical interconnection. The model and the bonding effect of this technique are discussed. In addition, in order to enhance the performance of titanium (Ti) getter, the prepared and activation parameters of Ti getter under different sputtering conditions are optimized and discussed. Based on the optimized results, the Ti getter (thickness of 300 nm to 500 nm) is also deposited on the inside of the glass groove by magnetron sputtering to maintain stable quality factor (Q). The Q test of the built testing system shows that the number of resonators with a Q value of more than 10,000 accounts for more than 73% of the total. With an interval of 1.5 years, the Q value of the samples remains almost constant. It proves the proposed cross-layer anodic bonding and getter technique can realize high-Q resonant structure for long-term stable operation.

Flight Simulation of ARES in the Mars Environment

NASA Technical Reports Server (NTRS)

Kenney, P. Sean; Croom, Mark A.

2011-01-01

A report discusses using the Aerial Regional- scale Environmental Survey (ARES) light airplane as an observation platform on Mars in order to gather data. It would have to survive insertion into the atmosphere, fly long enough to meet science objectives, and provide a stable platform. The feasibility of such a platform was tested using the Langley Standard Real- Time Simulation in C++. The unique features of LaSRS++ are: full, six-degrees- of-freedom flight simulation that can be used to evaluate the performance of the aircraft in the Martian environment; capability of flight analysis from start to finish; support of Monte Carlo analysis of aircraft performance; and accepting initial conditions from POST results for the entry and deployment of the entry body. Starting with a general aviation model, the design was tweaked to maintain a stable aircraft under expected Martian conditions. Outer mold lines were adjusted based on experience with the Martian atmosphere. Flight control was modified from a vertical acceleration control law to an angle-of-attack control law. Navigation was modified from a vertical acceleration control system to an alpha control system. In general, a pattern of starting with simple models with well-understood behaviors was selected and modified during testing.

Techniques for establishing schedules with wheel running as reinforcement in rats.

PubMed

Iversen, I H

1993-07-01

In three experiments, access to wheel running was contingent on lever pressing. In each experiment, the duration of access to running was reduced gradually to 4, 5, or 6 s, and the schedule parameters were expanded gradually. The sessions lasted 2 hr. In Experiment 1, a fixed-ratio 20 schedule controlled a typical break-and-run pattern of lever pressing that was maintained throughout the session for 3 rats. In Experiment 2, a fixed-interval schedule of 6 min maintained lever pressing throughout the session for 3 rats, and for 1 rat, the rate of lever pressing was positively accelerated between reinforcements. In Experiment 3, a variable-ratio schedule of 20 or 35 was in effect and maintained lever pressing at a very stable pace throughout the session for 2 of 3 rats; for 1 rat, lever pressing was maintained at an irregular rate. When the session duration was extended to successive 24-hr periods, with food and water accessible in Experiment 3, lever pressing settled into a periodic pattern occurring at a high rate at approximately the same time each day. In each experiment, the rats that developed the highest local rates of running during wheel access also maintained the most stable and highest rates of lever pressing.

Self-Recalibrating Surface EMG Pattern Recognition for Neuroprosthesis Control Based on Convolutional Neural Network

PubMed Central

Zhai, Xiaolong; Jelfs, Beth; Chan, Rosa H. M.; Tin, Chung

2017-01-01

Hand movement classification based on surface electromyography (sEMG) pattern recognition is a promising approach for upper limb neuroprosthetic control. However, maintaining day-to-day performance is challenged by the non-stationary nature of sEMG in real-life operation. In this study, we propose a self-recalibrating classifier that can be automatically updated to maintain a stable performance over time without the need for user retraining. Our classifier is based on convolutional neural network (CNN) using short latency dimension-reduced sEMG spectrograms as inputs. The pretrained classifier is recalibrated routinely using a corrected version of the prediction results from recent testing sessions. Our proposed system was evaluated with the NinaPro database comprising of hand movement data of 40 intact and 11 amputee subjects. Our system was able to achieve ~10.18% (intact, 50 movement types) and ~2.99% (amputee, 10 movement types) increase in classification accuracy averaged over five testing sessions with respect to the unrecalibrated classifier. When compared with a support vector machine (SVM) classifier, our CNN-based system consistently showed higher absolute performance and larger improvement as well as more efficient training. These results suggest that the proposed system can be a useful tool to facilitate long-term adoption of prosthetics for amputees in real-life applications. PMID:28744189

Self-Recalibrating Surface EMG Pattern Recognition for Neuroprosthesis Control Based on Convolutional Neural Network.

PubMed

Zhai, Xiaolong; Jelfs, Beth; Chan, Rosa H M; Tin, Chung

2017-01-01

Hand movement classification based on surface electromyography (sEMG) pattern recognition is a promising approach for upper limb neuroprosthetic control. However, maintaining day-to-day performance is challenged by the non-stationary nature of sEMG in real-life operation. In this study, we propose a self-recalibrating classifier that can be automatically updated to maintain a stable performance over time without the need for user retraining. Our classifier is based on convolutional neural network (CNN) using short latency dimension-reduced sEMG spectrograms as inputs. The pretrained classifier is recalibrated routinely using a corrected version of the prediction results from recent testing sessions. Our proposed system was evaluated with the NinaPro database comprising of hand movement data of 40 intact and 11 amputee subjects. Our system was able to achieve ~10.18% (intact, 50 movement types) and ~2.99% (amputee, 10 movement types) increase in classification accuracy averaged over five testing sessions with respect to the unrecalibrated classifier. When compared with a support vector machine (SVM) classifier, our CNN-based system consistently showed higher absolute performance and larger improvement as well as more efficient training. These results suggest that the proposed system can be a useful tool to facilitate long-term adoption of prosthetics for amputees in real-life applications.

Biochemical and Spectroscopic Characterization of Highly Stable Photosystem II Supercomplexes from Arabidopsis*

PubMed Central

Crepin, Aurelie; Santabarbara, Stefano; Caffarri, Stefano

2016-01-01

Photosystem II (PSII) is a large membrane supercomplex involved in the first step of oxygenic photosynthesis. It is organized as a dimer, with each monomer consisting of more than 20 subunits as well as several cofactors, including chlorophyll and carotenoid pigments, lipids, and ions. The isolation of stable and homogeneous PSII supercomplexes from plants has been a hindrance for their deep structural and functional characterization. In recent years, purification of complexes with different antenna sizes was achieved with mild detergent solubilization of photosynthetic membranes and fractionation on a sucrose gradient, but these preparations were only stable in the cold for a few hours. In this work, we present an improved protocol to obtain plant PSII supercomplexes that are stable for several hours/days at a wide range of temperatures and can be concentrated without degradation. Biochemical and spectroscopic properties of the purified PSII are presented, as well as a study of the complex solubility in the presence of salts. We also tested the impact of a large panel of detergents on PSII stability and found that very few are able to maintain the integrity of PSII. Such new PSII preparation opens the possibility of performing experiments that require room temperature conditions and/or high protein concentrations, and thus it will allow more detailed investigations into the structure and molecular mechanisms that underlie plant PSII function. PMID:27432883

Real-time inextensible surgical thread simulation.

PubMed

Xu, Lang; Liu, Qian

2018-03-27

This paper discusses a real-time simulation method of inextensible surgical thread based on the Cosserat rod theory using position-based dynamics (PBD). The method realizes stable twining and knotting of surgical thread while including inextensibility, bending, twisting and coupling effects. The Cosserat rod theory is used to model the nonlinear elastic behavior of surgical thread. The surgical thread model is solved with PBD to achieve a real-time, extremely stable simulation. Due to the one-dimensional linear structure of surgical thread, the direct solution of the distance constraint based on tridiagonal matrix algorithm is used to enhance stretching resistance in every constraint projection iteration. In addition, continuous collision detection and collision response guarantee a large time step and high performance. Furthermore, friction is integrated into the constraint projection process to stabilize the twining of multiple threads and complex contact situations. Through comparisons with existing methods, the surgical thread maintains constant length under large deformation after applying the direct distance constraint in our method. The twining and knotting of multiple threads correspond to stable solutions to contact and friction forces. A surgical suture scene is also modeled to demonstrate the practicality and simplicity of our method. Our method achieves stable and fast simulation of inextensible surgical thread. Benefiting from the unified particle framework, the rigid body, elastic rod, and soft body can be simultaneously simulated. The method is appropriate for applications in virtual surgery that require multiple dynamic bodies.

Humans as holobionts: implications for prevention and therapy.

PubMed

van de Guchte, Maarten; Blottière, Hervé M; Doré, Joël

2018-05-01

The human gut microbiota is increasingly recognized for its important or even decisive role in health. As it becomes clear that microbiota and host mutually affect and depend on each other in an intimate relationship, a holistic view of the gut microbiota-host association imposes itself. Ideally, a stable state of equilibrium, homeostasis, is maintained and serves health, but signs are that perturbation of this equilibrium beyond the limits of resilience can propel the system into an alternative stable state, a pre-disease state, more susceptible to the development of chronic diseases. The microbiota-host equilibrium of a large and growing proportion of individuals in Western society may represent such a pre-disease state and explain the explosive development of chronic diseases such as inflammatory bowel disease, obesity, and other inflammatory diseases. These diseases themselves represent other alternative stable states again and are therefore hard to cure. The holistic view of the microbiota-host association where feedback loops between microbiota and host are thought to maintain the system in a stable state-be it a healthy, pre-disease, or disease state-implies that integrated approaches, addressing host processes and microbiota, should be used to treat or prevent (pre-)disease.

A Dynamic Connectome Supports the Emergence of Stable Computational Function of Neural Circuits through Reward-Based Learning.

PubMed

Kappel, David; Legenstein, Robert; Habenschuss, Stefan; Hsieh, Michael; Maass, Wolfgang

2018-01-01

Synaptic connections between neurons in the brain are dynamic because of continuously ongoing spine dynamics, axonal sprouting, and other processes. In fact, it was recently shown that the spontaneous synapse-autonomous component of spine dynamics is at least as large as the component that depends on the history of pre- and postsynaptic neural activity. These data are inconsistent with common models for network plasticity and raise the following questions: how can neural circuits maintain a stable computational function in spite of these continuously ongoing processes, and what could be functional uses of these ongoing processes? Here, we present a rigorous theoretical framework for these seemingly stochastic spine dynamics and rewiring processes in the context of reward-based learning tasks. We show that spontaneous synapse-autonomous processes, in combination with reward signals such as dopamine, can explain the capability of networks of neurons in the brain to configure themselves for specific computational tasks, and to compensate automatically for later changes in the network or task. Furthermore, we show theoretically and through computer simulations that stable computational performance is compatible with continuously ongoing synapse-autonomous changes. After reaching good computational performance it causes primarily a slow drift of network architecture and dynamics in task-irrelevant dimensions, as observed for neural activity in motor cortex and other areas. On the more abstract level of reinforcement learning the resulting model gives rise to an understanding of reward-driven network plasticity as continuous sampling of network configurations.

A Dynamic Connectome Supports the Emergence of Stable Computational Function of Neural Circuits through Reward-Based Learning

PubMed Central

Habenschuss, Stefan; Hsieh, Michael

2018-01-01

Synaptic connections between neurons in the brain are dynamic because of continuously ongoing spine dynamics, axonal sprouting, and other processes. In fact, it was recently shown that the spontaneous synapse-autonomous component of spine dynamics is at least as large as the component that depends on the history of pre- and postsynaptic neural activity. These data are inconsistent with common models for network plasticity and raise the following questions: how can neural circuits maintain a stable computational function in spite of these continuously ongoing processes, and what could be functional uses of these ongoing processes? Here, we present a rigorous theoretical framework for these seemingly stochastic spine dynamics and rewiring processes in the context of reward-based learning tasks. We show that spontaneous synapse-autonomous processes, in combination with reward signals such as dopamine, can explain the capability of networks of neurons in the brain to configure themselves for specific computational tasks, and to compensate automatically for later changes in the network or task. Furthermore, we show theoretically and through computer simulations that stable computational performance is compatible with continuously ongoing synapse-autonomous changes. After reaching good computational performance it causes primarily a slow drift of network architecture and dynamics in task-irrelevant dimensions, as observed for neural activity in motor cortex and other areas. On the more abstract level of reinforcement learning the resulting model gives rise to an understanding of reward-driven network plasticity as continuous sampling of network configurations. PMID:29696150

Angular stable plates in proximal meta-epiphyseal tibial fractures: study of joint restoration and clinical and functional evaluation.

PubMed

Giannotti, S; Giovannelli, D; Dell'Osso, G; Bottai, V; Bugelli, G; Celli, F; Citarelli, C; Guido, G

2016-04-01

The tibial plateau fractures involve one of the main weight bearing joints of the human body. The goals of surgical treatment are anatomical reduction, articular surface reconstruction and high primary stability. The aim of this study was to evaluate the clinical and functional outcomes after internal plate fixation of this kind of fractures. From January 2009 to December 2012, we treated 75 cases of tibial plateau fracture with angular stable plates. We used Rasmussen Score and the Knee Society Score for the clinical and functional evaluation. Twenty-five cases that underwent hardware removal had arthroscopic and CT evaluation of the joint. No complications occurred. The clinical and functional evaluation, performed by the KSS and Rasmussen Score, highlighted the high percentage of good-to-excellent results (over 90 %). In every case, the range of motion was good with flexion >90°. Arthroscopy showed the presence of chondral damage in 100 % of patients. In all the cases, we found that X-ray images seem better than the CT images. Angular stable plates allow to obtain a good primary stability, permitting an early joint recovery with an excellent range of motion. Avoiding to perform a knee arthrotomy at the time of fracture reduction could prove to be an advantage in terms of functional recovery. The meniscus on the injured bone should be preserved in order to maintain good function of the joint. X-ray images remain the gold standard in checking the progression of post-traumatic osteoarthritis.

Heterosexual Male Carriers Could Explain Persistence of Homosexuality in Men: Individual-Based Simulations of an X-Linked Inheritance Model.

PubMed

Chaladze, Giorgi

2016-10-01

Homosexuality has been documented throughout history and is found in almost all human cultures. Twin studies suggest that homosexuality is to some extent heritable. However, from an evolutionary perspective, this poses a problem: Male homosexuals tend to have on average five times fewer children than heterosexual males, so how can a phenomenon associated with low reproductive success be maintained at relatively stable frequencies? Recent findings of increased maternal fecundity of male homosexuals suggest that the genes responsible for homosexuality in males increase fecundity in the females who carry them. Can an increase in maternal fecundity compensate for the fecundity reduction in homosexual men and produce a stable polymorphism? In the current study, this problem was addressed with an individual-based modeling (IBM) approach. IBM suggests that male homosexuality can be maintained in a population at low and stable frequencies if roughly more than half of the females and half of the males are carriers of genes that predispose the male to homosexuality.

Actuation of an Inertia-Coupled Rimless Wheel Model across Level Ground

NASA Astrophysics Data System (ADS)

Weeks, Seth Caleb

The inertia-coupled rimless wheel model is a passive dynamic walking device which is theoretically capable of achieving highly efficient motion with no energy losses. Under non-ideal circumstances, energy losses due to air drag require the use of actuation to maintain stable motions. The Actuated Inertia-coupled Rimless Wheel Across Flat Terrain (AIRWAFT) model provides actuation to an inertia-coupled rimless wheel model across level ground to compensate for energy losses by applying hip-torque between the frame and inertia wheel via a motor. Two methods of defining the open-loop actuation are presented. Position control defines the relative position of the drum relative to the frame. Torque control specifies the amount of torque between the frame and the drum. The performance of the model was evaluated with respect to changes in various geometrical and control parameters and initial conditions. This parameter study led to the discovery of a stable, periodic motion with a cost of transport of 0.33.

Design and Preparation of Carbon Based Composite Phase Change Material for Energy Piles.

PubMed

Yang, Haibin; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi; Li, Dongxu

2017-04-07

Energy piles-A fairly new renewable energy concept-Use a ground heat exchanger (GHE) in the foundation piles to supply heating and cooling loads to the supported building. Applying phase change materials (PCMs) to piles can help in maintaining a stable temperature within the piles and can then influence the axial load acting on the piles. In this study, two kinds of carbon-based composite PCMs (expanded graphite-based PCM and graphite nanoplatelet-based PCM) were prepared by vacuum impregnation for potential application in energy piles. Thereafter, a systematic study was performed and different characterization tests were carried out on two composite PCMs. The composite PCMs retained up to 93.1% of paraffin and were chemically compatible, thermally stable and reliable. The latent heat of the composite PCM was up to 152.8 J/g while the compressive strength of cement paste containing 10 wt % GNP-PCM was found to be 37 MPa. Hence, the developed composite PCM has potential for thermal energy storage applications.

Integration of aerobic granular sludge and mesh filter membrane bioreactor for cost-effective wastewater treatment.

PubMed

Li, Wen-Wei; Wang, Yun-Kun; Sheng, Guo-Ping; Gui, Yong-Xin; Yu, Lei; Xie, Tong-Qing; Yu, Han-Qing

2012-10-01

Conventional MBR has been mostly based on floc sludge and the use of costly microfiltration membranes. Here, a novel aerobic granule (AG)-mesh filter MBR (MMBR) process was developed for cost-effective wastewater treatment. During 32-day continuous operation, a predominance of granules was maintained in the system, and good filtration performance was achieved at a low trans-membrane pressure (TMP) of below 0.025 m. The granules showed a lower fouling propensity than sludge flocs, attributed to the formation of more porous biocake layer at mesh surface. A low-flux and low-TMP filtration favored a stable system operation. In addition, the reactor had high pollutant removal efficiencies, with a 91.4% chemical oxygen demand removal, 95.7% NH(4)(+) removal, and a low effluent turbidity of 4.1 NTU at the stable stage. This AG-MMBR process offers a promising technology for low-cost and efficient treatment of wastewaters. Copyright © 2012 Elsevier Ltd. All rights reserved.

Uncovering inherent cellular plasticity of multiciliated ependyma leading to ventricular wall transformation and hydrocephalus.

PubMed

Abdi, Khadar; Lai, Chun-Hsiang; Paez-Gonzalez, Patricia; Lay, Mark; Pyun, Joon; Kuo, Chay T

2018-04-25

Specialized, differentiated cells often perform unique tasks that require them to maintain a stable phenotype. Multiciliated ependymal cells (ECs) are unique glial cells lining the brain ventricles, important for cerebral spinal fluid circulation. While functional ECs are needed to prevent hydrocephalus, they have also been reported to generate new neurons: whether ECs represent a stable cellular population remains unclear. Via a chemical screen we found that mature ECs are inherently plastic, with their multiciliated state needing constant maintenance by the Foxj1 transcription factor, which paradoxically is rapidly turned over by the ubiquitin-proteasome system leading to cellular de-differentiation. Mechanistic analyses revealed a novel NF-κB-independent IKK2 activity stabilizing Foxj1 in mature ECs, and we found that known IKK2 inhibitors including viruses and growth factors robustly induced Foxj1 degradation, EC de-differentiation, and hydrocephalus. Although mature ECs upon de-differentiation can divide and regenerate multiciliated ECs, we did not detect evidence supporting EC's neurogenic potential.

Design and Preparation of Carbon Based Composite Phase Change Material for Energy Piles

PubMed Central

Yang, Haibin; Memon, Shazim Ali; Bao, Xiaohua; Cui, Hongzhi; Li, Dongxu

2017-01-01

Energy piles—A fairly new renewable energy concept—Use a ground heat exchanger (GHE) in the foundation piles to supply heating and cooling loads to the supported building. Applying phase change materials (PCMs) to piles can help in maintaining a stable temperature within the piles and can then influence the axial load acting on the piles. In this study, two kinds of carbon-based composite PCMs (expanded graphite-based PCM and graphite nanoplatelet-based PCM) were prepared by vacuum impregnation for potential application in energy piles. Thereafter, a systematic study was performed and different characterization tests were carried out on two composite PCMs. The composite PCMs retained up to 93.1% of paraffin and were chemically compatible, thermally stable and reliable. The latent heat of the composite PCM was up to 152.8 J/g while the compressive strength of cement paste containing 10 wt % GNP-PCM was found to be 37 MPa. Hence, the developed composite PCM has potential for thermal energy storage applications. PMID:28772752

Composite of K-doped (NH4)2V3O8/graphene as an anode material for sodium-ion batteries.

PubMed

Liu, Xin; Li, Zhiwei; Fei, Hailong; Wei, Mingdeng

2015-11-21

A layer structured K-doped (NH4)2V3O8/graphene (K-NVG) was prepared via a hydrothermal route and then used as an anode material for sodium-ion batteries for the first time. The K-NVG nanosheets have a diameter in the range of 200-500 nm. The K-NVG electrode exhibited stable cycling and a good rate performance with a reversible capacity of 235.4 mA h g(-1), which is much higher than the 90.5 mA h g(-1) value of the (NH4)2V3O8/graphene electrode after 100 cycles at a current density of 100 mA g(-1). Simultaneously, the retention rate was maintained at 82% even after 250 cycles at the current density of 300 mA g(-1). Such good electrochemical properties may be attributed to the K-NVG's stable layered structure.

Improving stability of regional numerical ocean models

NASA Astrophysics Data System (ADS)

Herzfeld, Mike

2009-02-01

An operational limited-area ocean modelling system was developed to supply forecasts of ocean state out to 3 days. This system is designed to allow non-specialist users to locate the model domain anywhere within the Australasian region with minimum user input. The model is required to produce a stable simulation every time it is invoked. This paper outlines the methodology used to ensure the model remains stable over the wide range of circumstances it might encounter. Central to the model configuration is an alternative approach to implementing open boundary conditions in a one-way nesting environment. Approximately 170 simulations were performed on limited areas in the Australasian region to assess the model stability; of these, 130 ran successfully with a static model parameterisation allowing a statistical estimate of the model’s approach toward instability to be determined. Based on this, when the model was deemed to be approaching instability a strategy of adaptive intervention in the form of constraint on velocity and elevation was invoked to maintain stability.

Long-term stable water vapor permeation barrier properties of SiN/SiCN/SiN nanolaminated multilayers grown by plasma-enhanced chemical vapor deposition at extremely low pressures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Bum Ho, E-mail: bhchoi@kitech.re.kr; Lee, Jong Ho

2014-08-04

We investigated the water vapor permeation barrier properties of 30-nm-thick SiN/SiCN/SiN nanolaminated multilayer structures grown by plasma enhanced chemical vapor deposition at 7 mTorr. The derived water vapor transmission rate was 1.12 × 10{sup −6} g/(m{sup 2} day) at 85 °C and 85% relative humidity, and this value was maintained up to 15 000 h of aging time. The X-ray diffraction patterns revealed that the nanolaminated film was composed of an amorphous phase. A mixed phase was observed upon performing high resolution transmission electron microscope analysis, which indicated that a thermodynamically stable structure was formed. It was revealed amorphous SiN/SiCN/SiN multilayer structures that are freemore » from intermixed interface defects effectively block water vapor permeation into active layer.« less

Long-term performance of anaerobic digestion for crop residues containing heavy metals and response of microbial communities.

PubMed

Lee, Jongkeun; Kim, Joonrae Roger; Jeong, Seulki; Cho, Jinwoo; Kim, Jae Young

2017-01-01

In order to investigate the long-term stability on the performance of the anaerobic digestion process, a laboratory-scale continuous stirred-tank reactor (CSTR) was operated for 1100 days with sunflower harvested in a heavy metal contaminated site. Changes of microbial communities during digestion were identified using pyrosequencing. According to the results, soluble heavy metal concentrations were lower than the reported inhibitory level and the reactor performance remained stable up to OLR of 2.0g-VS/L/day at HRT of 20days. Microbial communities commonly found in anaerobic digestion for cellulosic biomass were observed and stably established with respect to the substrate. Thus, the balance of microbial metabolism was maintained appropriately and anaerobic digestion seems to be feasible for disposal of heavy metal-containing crop residues from phytoremediation sites. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Nursing care time in a teaching hospital].

PubMed

Rogenski, Karin Emília; Fugulin, Fernanda Maria Togeiro; Gaidzinski, Raquel Rapone; Rogenski, Noemi Marisa Brunet

2011-03-01

This is a quantitative exploratory, descriptive study performed with the objective to identify and analyze the performance of the average time of nursing care delivered to patients of the Inpatient Units of the University Hospital at University of São Paulo (UH-USP), from 2001 to 2005. The average nursing care time delivered to patients of the referred units was identified by applying of a mathematical equation proposed in the literature, after surveying data from the Medical and Statistical Service and based on the monthly working shifts of the nursing professionals. Data analysis was performed using descriptive statistics. The average nursing care time observed in most units, despite some variations, remained stable during the analyzed period. Based on this observed stability, it is concluded that the nursing staff in the referred HU-USP units has been continuously evaluated with the purposes of maintaining the average time of assistance and, thus, the quality of the care being delivered.

High-precision buffer circuit for suppression of regenerative oscillation

NASA Technical Reports Server (NTRS)

Tripp, John S.; Hare, David A.; Tcheng, Ping

1995-01-01

Precision analog signal conditioning electronics have been developed for wind tunnel model attitude inertial sensors. This application requires low-noise, stable, microvolt-level DC performance and a high-precision buffered output. Capacitive loading of the operational amplifier output stages due to the wind tunnel analog signal distribution facilities caused regenerative oscillation and consequent rectification bias errors. Oscillation suppression techniques commonly used in audio applications were inadequate to maintain the performance requirements for the measurement of attitude for wind tunnel models. Feedback control theory is applied to develop a suppression technique based on a known compensation (snubber) circuit, which provides superior oscillation suppression with high output isolation and preserves the low-noise low-offset performance of the signal conditioning electronics. A practical design technique is developed to select the parameters for the compensation circuit to suppress regenerative oscillation occurring when typical shielded cable loads are driven.

Space shuttle maneuvering engine reusable thrust chamber program. Task 11: Low Epsilon stability test plan

NASA Technical Reports Server (NTRS)

Pauckert, R. P.

1974-01-01

The performance and heat transfer characteristics of a doublet element type injector for the space shuttle orbiter maneuvering engine thrust chamber were investigated. Ths stability characteristics were evaluated over a range of chamber pressures and mixture ratios. The specific objectives of the test were: (1) to determine whether stability has been influenced by injection of boundary layer coolant across the cavity entrance, (2) if the injector is stable, to determine the minimum cavity area required to maintain stability, and (3) if the injector is unstable, to determine the effects of entrance geometry and increased area on stability.

Investigation of micro burner performance during porous media combustion for surface and submerged flames

NASA Astrophysics Data System (ADS)

Janvekar, Ayub Ahmed; Abdullah, M. Z.; Ahmad, Z. A.; Abas, Aizat; Hussien, Ahmed A.; Kataraki, Pramod S.; Mohamed, Mazlan; Husin, Azmi; Fadzli, Khairil

2018-05-01

Porous media combustion is considered to be one of the popular choice due to its tremendous advantages. Such type of combustion liberates not only super stable flame but also maintains emissions parameters below thresholds level. Present study incorporates reaction and preheat layer with discrete and foam type of materials respectively. Burner was made to run in ultra-lean mode. Optimum equivalence ratio was found out to be 0.7 for surface flame, while 0.6 during submerged flame condition. Maximum thermal efficiency was noted to be 81%. Finally, emissions parameters where recorded continuously to measure NOx and CO, which were under global limits.

Sub-femtosecond timing jitter, all-fiber, CNT-mode-locked Er-laser at telecom wavelength.

PubMed

Kim, Chur; Bae, Sangho; Kieu, Khanh; Kim, Jungwon

2013-11-04

We demonstrate a 490-attosecond timing jitter (integration bandwidth: 10 kHz - 39.4 MHz) optical pulse train from a 78.7-MHz repetition rate, all-fiber soliton Er laser mode-locked by a fiber tapered carbon nanotube saturable absorber (ft-CNT-SA). To achieve this jitter performance, we searched for a net cavity dispersion condition where the Gordon-Haus jitter is minimized while maintaining stable soliton mode-locking. Our result shows that optical pulse trains with well below a femtosecond timing jitter can be generated from a self-starting and robust all-fiber laser operating at telecom wavelength.

Modeling of nitrogen transformation in an integrated multi-trophic aquaculture (IMTA)

NASA Astrophysics Data System (ADS)

Silfiana; Widowati; Putro, S. P.; Udjiani, T.

2018-03-01

The dynamic model of nitrogen transformation in IMTA (Integrated Multi-Trophic Aquaculture) is purposed. IMTA is a polyculture with several biotas maintained in it to optimize waste recycling as a food source. The purpose of this paper is to predict nitrogen decrease and nitrogen transformation in IMTA consisting of ammonia (NH3), Nitrite (NO2) and Nitrate (NO3). Nitrogen transformation of several processes, nitrification, assimilation, and volatilization. Numerical simulations are performed by providing initial parameters and values based on a review of previous research. The numerical results show that the rate of change in nitrogen concentration in IMTA decrease and reaches stable at different times.

Patterns of Change in Collaboration Are Associated with Baseline Characteristics and Predict Outcome and Dropout Rates in Treatment of Multi-Problem Families. A Validation Study

PubMed Central

Bachler, Egon; Fruehmann, Alexander; Bachler, Herbert; Aas, Benjamin; Nickel, Marius; Schiepek, Guenter K.

2017-01-01

Objective: The present study validates the Multi-Problem Family (MPF)-Collaboration Scale), which measures the progress of goal directed collaboration of patients in the treatment of families with MPF and its relation to drop-out rates and treatment outcome. Method: Naturalistic study of symptom and competence-related changes in children of ages 4–18 and their caregivers. Setting: Integrative, structural outreach family therapy. Measures: The data of five different groups of goal directed collaboration (deteriorating collaboration, stable low collaboration, stable medium collaboration, stable high collaboration, improving collaboration) were analyzed in their relation to treatment expectation, individual therapeutic goals (ITG), family adversity index, severity of problems and global assessment of a caregiver’s functioning, child, and relational aspects. Results: From N = 810 families, 20% displayed stable high collaboration (n = 162) and 21% had a pattern of improving collaboration. The families with stable high or improving collaboration rates achieved significantly more progress throughout therapy in terms of treatment outcome expectancy (d = 0.96; r = 0.43), reaching ITG (d = 1.17; r = 0.50), family adversities (d = 0.55; r = 0.26), and severity of psychiatric symptoms (d = 0.31; r = 0.15). Furthermore, families with stable high or improving collaboration maintained longer treatments and had a bigger chance of finishing the therapy as planned. The odds of having a stable low or deteriorating collaboration throughout treatment were significantly higher for subjects who started treatment with low treatment expectation or high family-related adversities. Conclusion: The positive outcomes of homebased interventions for multi-problem families are closely related to “stable high” and an “improving” collaboration as measured with the MPF-Collaboration Scale. Patients who fall into these groups have a high treatment outcome expectancy and reduce psychological stress. For therapeutic interventions with multi-problem families it seems beneficial to maintain a stable high collaboration or help the collaboration, e.g., by fostering treatment expectation. PMID:28785232

UV durable colour pigment doped SmA liquid crystal composites for outdoor trans-reflective bi-stable displays

NASA Astrophysics Data System (ADS)

Xu, H.; Davey, A. B.; Crossland, W. A.; Chu, D. P.

2012-10-01

High brightness trans-reflective bi-stable displays based on smectic A (SmA) liquid crystals (LCs) can have nearly perfect transparency in the clear state and very high reflection in the scattered state. Because the LC material in use is stable under UV radiation, this kind of displays can stand for strong day-light and therefore be ideal for outdoor applications from e-books to public signage and advertisement. However, the colour application has been limited because the traditional colourants in use are conventional dyes which are lack of UV stability and that their colours are easily photo bleached. Here we present a colour SmA display demonstrator using pigments as colourant. Mixing pigments with SmA LCs and maintain the desirable optical switching performance is not straightforward. We show here how it can be done, including how to obtain fine sized pigment nano-particles, the effects of particle size and size distribution on the display performance. Our optimized pigments/SmA compositions can be driven by a low frequency waveform (~101Hz) to a scattered state to exhibit colour while by a high frequency waveform (~103Hz) to a cleared state showing no colour. Finally, we will present its excellent UV life-time (at least <7.2 years) in comparison with that of dye composition (~2.4 years). The complex interaction of pigment nano-particles with LC molecules and the resulting effects on the LC electro-optical performances are still to be fully understood. We hope this work will not only demonstrate a new and practical approach for outdoor reflective colour displays but also provide a new material system for fundamental liquid crystal colloid research work.

Hydraulic performance of compacted clay liners under simulated daily thermal cycles.

PubMed

Aldaeef, A A; Rayhani, M T

2015-10-01

Compacted clay liners (CCLs) are commonly used as hydraulic barriers in several landfill applications to isolate contaminants from the surrounding environment and minimize the escape of leachate from the landfill. Prior to waste placement in landfills, CCLs are often exposed to temperature fluctuations which can affect the hydraulic performance of the liner. Experimental research was carried out to evaluate the effects of daily thermal cycles on the hydraulic performance of CCLs under simulated landfill conditions. Hydraulic conductivity tests were conducted on different soil specimens after being exposed to various thermal and dehydration cycles. An increase in the CCL hydraulic conductivity of up to one order of magnitude was recorded after 30 thermal cycles for soils with low plasticity index (PI = 9.5%). However, medium (PI = 25%) and high (PI = 37.2%) plasticity soils did not show significant hydraulic deviation due to their self-healing potential. Overlaying the CCL with a cover layer minimized the effects of daily thermal cycles, and maintained stable hydraulic performance in the CCLs even after exposure to 60 thermal cycles. Wet-dry cycles had a significant impact on the hydraulic aspect of low plasticity CCLs. However, medium and high plasticity CCLs maintained constant hydraulic performance throughout the test intervals. The study underscores the importance of protecting the CCL from exposure to atmosphere through covering it by a layer of geomembrane or an interim soil layer. Copyright © 2015 Elsevier Ltd. All rights reserved.

When Does Frequency-Independent Selection Maintain Genetic Variation?

PubMed

Novak, Sebastian; Barton, Nicholas H

2017-10-01

Frequency-independent selection is generally considered as a force that acts to reduce the genetic variation in evolving populations, yet rigorous arguments for this idea are scarce. When selection fluctuates in time, it is unclear whether frequency-independent selection may maintain genetic polymorphism without invoking additional mechanisms. We show that constant frequency-independent selection with arbitrary epistasis on a well-mixed haploid population eliminates genetic variation if we assume linkage equilibrium between alleles. To this end, we introduce the notion of frequency-independent selection at the level of alleles, which is sufficient to prove our claim and contains the notion of frequency-independent selection on haploids. When selection and recombination are weak but of the same order, there may be strong linkage disequilibrium; numerical calculations show that stable equilibria are highly unlikely. Using the example of a diallelic two-locus model, we then demonstrate that frequency-independent selection that fluctuates in time can maintain stable polymorphism if linkage disequilibrium changes its sign periodically. We put our findings in the context of results from the existing literature and point out those scenarios in which the possible role of frequency-independent selection in maintaining genetic variation remains unclear. Copyright © 2017 by the Genetics Society of America.

ATLAST ULE mirror segment performance analytical predictions based on thermally induced distortions

NASA Astrophysics Data System (ADS)

Eisenhower, Michael J.; Cohen, Lester M.; Feinberg, Lee D.; Matthews, Gary W.; Nissen, Joel A.; Park, Sang C.; Peabody, Hume L.

2015-09-01

The Advanced Technology Large-Aperture Space Telescope (ATLAST) is a concept for a 9.2 m aperture space-borne observatory operating across the UV/Optical/NIR spectra. The primary mirror for ATLAST is a segmented architecture with pico-meter class wavefront stability. Due to its extraordinarily low coefficient of thermal expansion, a leading candidate for the primary mirror substrate is Corning's ULE® titania-silicate glass. The ATLAST ULE® mirror substrates will be maintained at `room temperature' during on orbit flight operations minimizing the need for compensation of mirror deformation between the manufacturing temperature and the operational temperatures. This approach requires active thermal management to maintain operational temperature while on orbit. Furthermore, the active thermal control must be sufficiently stable to prevent time-varying thermally induced distortions in the mirror substrates. This paper describes a conceptual thermal management system for the ATLAST 9.2 m segmented mirror architecture that maintains the wavefront stability to less than 10 pico-meters/10 minutes RMS. Thermal and finite element models, analytical techniques, accuracies involved in solving the mirror figure errors, and early findings from the thermal and thermal-distortion analyses are presented.

The Core Gut Microbiome of the American Cockroach, Periplaneta americana, Is Stable and Resilient to Dietary Shifts.

PubMed

Tinker, Kara A; Ottesen, Elizabeth A

2016-11-15

The omnivorous cockroach Periplaneta americana hosts a diverse hindgut microbiota encompassing hundreds of microbial species. In this study, we used 16S rRNA gene sequencing to examine the effect of diet on the composition of the P. americana hindgut microbial community. Results show that the hindgut microbiota of P. americana exhibit a highly stable core microbial community with low variance in compositions between individuals and minimal community change in response to dietary shifts. This core hindgut microbiome is shared between laboratory-hosted and wild-caught individuals, although wild-caught specimens exhibited a higher diversity of low-abundance microbes that were lost following extended cultivation under laboratory conditions. This taxonomic stability strongly contrasts with observations of the gut microbiota of mammals, which have been shown to be highly responsive to dietary change. A comparison of P. americana hindgut samples with human fecal samples indicated that the cockroach hindgut community exhibited higher alpha diversity but a substantially lower beta diversity than the human gut microbiome. This suggests that cockroaches have evolved unique mechanisms for establishing and maintaining a diverse and stable core microbiome. The gut microbiome plays an important role in the overall health of its host. A healthy gut microbiota typically assists with defense against pathogens and the digestion and absorption of nutrients from food, while dysbiosis of the gut microbiota has been associated with reduced health. In this study, we examined the composition and stability of the gut microbiota from the omnivorous cockroach Periplaneta americana. We found that P. americana hosts a diverse core gut microbiome that remains stable after drastic long-term changes in diet. While other insects, notably ant and bee species, have evolved mechanisms for maintaining a stable association with specific gut microbiota, these insects typically host low-diversity gut microbiomes and consume specialized diets. In contrast, P. americana hosts a gut microbiota that is highly species rich and consumes a diverse solid diet, suggesting that cockroaches have evolved unique mechanisms for developing and maintaining a stable gut microbiota. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Reacting flow studies in a dump combustor: Enhanced volumetric heat release rates and flame anchorability

NASA Astrophysics Data System (ADS)

Behrens, Alison Anne

Reacting flow studies in a novel dump combustor facility focused on increasing volumetric heat release rates, under stable burning conditions, and understanding the physical mechanisms governing flame anchoring in an effort to extend range and maneuverability of compact, low drag, air-breathing engines. Countercurrent shear flow was enhanced within the combustor as the primary control variable. Experiments were performed burning premixed JP10/air and methane/air in a dump combustor using reacting flow particle image velocimetry (PIV) and chemiluminescence as the primary diagnostics. Stable combustion studies burning lean mixtures of JP10/air aimed to increase volumetric heat release rates through the implementation of countercurrent shear control. Countercurrent shear flow was produced by creating a suction flow from a low pressure cavity connected to the dump combustor via a gap directly below the trailing edge. Chemiluminescence measurements showed that enhancing countercurrent shear within the combustor doubles volumetric heat release rates. PIV measurements indicate that counterflow acts to increase turbulent kinetic energy while maintaining constant strain rates. This acts to increase flame surface area through flame wrinkling without disrupting the integrity of the flame. Flame anchorability is one of the most important fundamental aspects to understand when trying to enhance turbulent combustion in a high-speed engine without increasing drag. Studies burning methane/air mixtures used reacting flow PIV to study flame anchoring. The operating point with the most stable flame anchor exhibited a correspondingly strong enthalpy flux of products into reactants via a single coherent structure positioned downstream of the step. However, the feature producing a strong flame anchor, i.e. a single coherent structure, also is responsible for combustion instabilities, therefore making this operating point undesirable. Counterflow control was found to create the best flow features for stable, robust, compact combustion. Enhancing countercurrent shear flow within a dump combustor enhances burning rates, provides a consistent pump of reaction-initiating combustion products required for sustained combustion, while maintaining flow three dimensionality needed to disrupt combustion instabilities. Future studies will focus on geometric and control scenarios that further reduce drag penalties while creating these same flow features found with countercurrent shear thus producing robust operating points.

Stable radio frequency dissemination by simple hybrid frequency modulation scheme.

PubMed

Yu, Longqiang; Wang, Rong; Lu, Lin; Zhu, Yong; Wu, Chuanxin; Zhang, Baofu; Wang, Peizhang

2014-09-15

In this Letter, we propose a fiber-based stable radio frequency transfer system by a hybrid frequency modulation scheme. Creatively, two radio frequency signals are combined and simultaneously transferred by only one laser diode. One frequency component is used to detect the phase fluctuation, and the other one is the derivative compensated signal providing a stable frequency for the remote end. A proper ratio of the frequencies of the components is well maintained by parameter m to avoid interference between them. Experimentally, a stable 200 MHz signal is transferred over 100 km optical fiber with the help of a 1 GHz detecting signal, and fractional instability of 2×10(-17) at 10(5) s is achieved.

Plate-only open door laminoplasty maintains stable spinal canal expansion with high rates of hinge union and no plate failures.

PubMed

Rhee, John M; Register, Bradley; Hamasaki, Takahiko; Franklin, Betty

2011-01-01

Prospective clinical series. To evaluate the ability of plate-only laminoplasty to achieve stable laminar arch reconstruction and to determine the rate and time course with which bony healing occurs in such constructs. Reconstruction of a stable laminar arch with sufficient room for the decompressed spinal cord is a desired goal when performing cervical laminoplasty for myelopathy. Traditional forms of laminoplasty fixation, such as sutures, bone struts, and ceramic spacers, may be associated with complications including loss of fixation, dislodgement with neurologic compromise, and premature laminoplasty closure. Plates, in contrast, provide more rigid fixation. Plate-only laminoplasty is gaining popularity as a method of laminoplasty fixation, but there is little data on its effectiveness. Fifty-four patients who underwent open door laminoplasty for cervical myelopathy and had available postoperative computed tomography (CT) scans formed the basis of this study. In all cases, a 4-mm round burr was used to create the hinge at the junction of the lateral mass and lamina by completely removing the dorsal cortex and thinning the ventral cortex until a greenstick deformation of the hinge could be produced. Laminoplasty plates were used as the sole method of fixation. No supplemental bone graft struts were used on the plated side, and the hinge side was not bone grafted. Axial CT scans obtained at 3, 6, and 12 months postoperatively were assessed for plate complications and bony healing of the hinge. No plate failures, dislodgements, or premature closures occurred in any of the levels at any time postoperatively. Computed tomography scan review demonstrated that 55% of levels were healed at 3 months, 77% at 6 months, and 93% at 12 months. At each timepoint, C6 and C7 had the highest hinge healing rates. Laminar screw backout was seen in 5/217 (2.3%) of levels, but was not associated with plate dislodgement, laminoplasty closure, or neurologic consequences, and did not occur in any case in which 2 laminar screws had been placed. Plate-only laminoplasty provided stable reconstruction of an expanded laminar arch with no failures, dislodgements, adverse neurologic consequences, or premature closures in 217 levels. Ninety-three percent of hinges demonstrated radiographic union at 12 months, and even those that did not heal by CT scan criteria maintained patent expansion of the spinal canal without adverse neurologic consequences. Supplemental bone graft does not appear necessary when plated laminoplasty is performed.

PEMFC development at Asahi Glass Co., Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoshitake, M.; Yanagisawa, E.; Naganuma, T.

2000-07-01

Perfluorinated ion exchange membranes were studied and the membrane technology for PEMFC has been developed. Thermal stability, mechanical strength, water content, AC specific resistance and gas permeability were measured. The influence of membrane thickness on gas permeability and the influence of incorporation of cations on water content and AC specific resistance of Flemion{reg_sign} and Nafion{reg_sign}117 were estimated. Gas permeation rates of the membranes decreased in inverse proportion to the increase of the membrane thickness and gas permeability coefficients were nearly constant and independent of the thickness. Hydrogen permeation rates of Flemion S at 70 C were converted to 2.1 mA/cm{supmore » 2} as current density. Flemion R-electrode assembly showed to maintain stable performance for over 3,500 hr. Furthermore, it was found that usage of thinner membranes of one with higher ion-exchange capacity gave not only lower internal cell voltage but also higher IR-free cell voltage. PTFE-yarn embedded type membrane (Flemion Mc and Sc) and PTFE-fibril dispersed type (Flemion Rf2) was examined to afford improvement in mechanical strength at moist and high temperature atmosphere. Flemion Sc (80{micro}m) was examined to give high cell performance of 0.67V at 0.5A/cm2, 80 C, 1 ata. Flemion Mc-electrode assembly was examined to keep stable performance during the life test of over 1,500 hr.« less

Design and performance of a trickling air biofilter for chlorobenzene and o-dichlorobenzene vapors.

PubMed Central

Oh, Y S; Bartha, R

1994-01-01

From contaminated industrial sludge, two stable multistrain microbial enrichments (consortia) that were capable of rapidly utilizing chlorobenzene and o-dichlorobenzene, respectively, were obtained. These consortia were characterized as to their species composition, tolerance range, and activity maxima in order to establish and maintain the required operational parameters during their use in biofilters for the removal of chlorobenzene contaminants from air. The consortia were immobilized on a porous perlite support packed into filter columns. Metered airstreams containing the contaminant vapors were partially humidified and passed through these columns. The vapor concentrations prior to and after biofiltration were measured by gas chromatography. Liquid was circulated concurrently with the air, and the device was operated in the trickling air biofilter mode. The experimental arrangement allowed the independent variation of liquid flow, airflow, and solvent vapor concentrations. Bench-scale trickling air biofilters removed monochlorobenzene, o-dichlorobenzene, and their mixtures at rates of up to 300 g of solvent vapor h(-1) m(-3) filter volume. High liquid recirculation rates and automated pH control were critical for stable filtration performance. When the accumulating NaCl was periodically diluted, the trickling air biofilters continued to remove chlorobenzenes for several months with no loss of activity. The demonstrated high performance and stability of the described trickling air biofilters favor their use in industrial-scale air pollution control. PMID:8085815

High-Temperature Stable Anatase Titanium Oxide Nanofibers for Lithium-Ion Battery Anodes.

PubMed

Lee, Sangkyu; Eom, Wonsik; Park, Hun; Han, Tae Hee

2017-08-02

Control of the crystal structure of electrochemically active materials is an important approach to fabricating high-performance electrodes for lithium-ion batteries (LIBs). Here, we report a methodology for controlling the crystal structure of TiO 2 nanofibers by adding aluminum isopropoxide to a common sol-gel precursor solution utilized to create TiO 2 nanofibers. The introduction of aluminum cations impedes the phase transformation of electrospun TiO 2 nanofibers from the anatase to the rutile phase, which inevitably occurs in the typical annealing process utilized for the formation of TiO 2 crystals. As a result, high-temperature stable anatase TiO 2 nanofibers were created in which the crystal structure was well-maintained even at high annealing temperatures of up to 700 °C. Finally, the resulting anatase TiO 2 nanofibers were utilized to prepare LIB anodes, and their electrochemical performance was compared to pristine TiO 2 nanofibers that contain both anatase and rutile phases. Compared to the electrode prepared with pristine TiO 2 nanofibers, the electrode prepared with anatase TiO 2 nanofibers exhibited excellent electrochemical performances such as an initial Coulombic efficiency of 83.9%, a capacity retention of 89.5% after 100 cycles, and a rate capability of 48.5% at a current density of 10 C (1 C = 200 mA g -1 ).

Sustained attention performance during sleep deprivation: evidence of state instability

NASA Technical Reports Server (NTRS)

Doran, S. M.; Van Dongen, H. P.; Dinges, D. F.

2001-01-01

Nathaniel Kleitman was the first to observe that sleep deprivation in humans did not eliminate the ability to perform neurobehavioral functions, but it did make it difficult to maintain stable performance for more than a few minutes. To investigate variability in performance as a function of sleep deprivation, n = 13 subjects were tested every 2 hours on a 10-minute, sustained-attention, psychomotor vigilance task (PVT) throughout 88 hours of total sleep deprivation (TSD condition), and compared to a control group of n = 15 subjects who were permitted a 2-hour nap every 12 hours (NAP condition) throughout the 88-hour period. PVT reaction time means and standard deviations increased markedly among subjects and within each individual subject in the TSD condition relative to the NAP condition. TSD subjects also had increasingly greater performance variability as a function of time on task after 18 hours of wakefulness. During sleep deprivation, variability in PVT performance reflected a combination of normal timely responses, errors of omission (i.e., lapses), and errors of commission (i.e., responding when no stimulus was present). Errors of omission and errors of commission were highly intercorrelated across deprivation in the TSD condition (r = 0.85, p = 0.0001), suggesting that performance instability is more likely to include compensatory effort than a lack of motivation. The marked increases in PVT performance variability as sleep loss continued supports the "state instability" hypothesis, which posits that performance during sleep deprivation is increasingly variable due to the influence of sleep initiating mechanisms on the endogenous capacity to maintain attention and alertness, thereby creating an unstable state that fluctuates within seconds and that cannot be characterized as either fully awake or asleep.

Process control of laser conduction welding by thermal imaging measurement with a color camera.

PubMed

Bardin, Fabrice; Morgan, Stephen; Williams, Stewart; McBride, Roy; Moore, Andrew J; Jones, Julian D C; Hand, Duncan P

2005-11-10

Conduction welding offers an alternative to keyhole welding. Compared with keyhole welding, it is an intrinsically stable process because vaporization phenomena are minimal. However, as with keyhole welding, an on-line process-monitoring system is advantageous for quality assurance to maintain the required penetration depth, which in conduction welding is more sensitive to changes in heat sinking. The maximum penetration is obtained when the surface temperature is just below the boiling point, and so we normally wish to maintain the temperature at this level. We describe a two-color optical system that we have developed for real-time temperature profile measurement of the conduction weld pool. The key feature of the system is the use of a complementary metal-oxide semiconductor standard color camera leading to a simplified low-cost optical setup. We present and discuss the real-time temperature measurement and control performance of the system when a defocused beam from a high power Nd:YAG laser is used on 5 mm thick stainless steel workpieces.

Calibration of the head direction network: a role for symmetric angular head velocity cells.

PubMed

Stratton, Peter; Wyeth, Gordon; Wiles, Janet

2010-06-01

Continuous attractor networks require calibration. Computational models of the head direction (HD) system of the rat usually assume that the connections that maintain HD neuron activity are pre-wired and static. Ongoing activity in these models relies on precise continuous attractor dynamics. It is currently unknown how such connections could be so precisely wired, and how accurate calibration is maintained in the face of ongoing noise and perturbation. Our adaptive attractor model of the HD system that uses symmetric angular head velocity (AHV) cells as a training signal shows that the HD system can learn to support stable firing patterns from poorly-performing, unstable starting conditions. The proposed calibration mechanism suggests a requirement for symmetric AHV cells, the existence of which has previously been unexplained, and predicts that symmetric and asymmetric AHV cells should be distinctly different (in morphology, synaptic targets and/or methods of action on postsynaptic HD cells) due to their distinctly different functions.

Thermally stable, highly efficient, ultraflexible organic photovoltaics

PubMed Central

Xu, Xiaomin; Fukuda, Kenjiro; Karki, Akchheta; Park, Sungjun; Kimura, Hiroki; Jinno, Hiroaki; Watanabe, Nobuhiro; Yamamoto, Shuhei; Shimomura, Satoru; Kitazawa, Daisuke; Yokota, Tomoyuki; Umezu, Shinjiro; Nguyen, Thuc-Quyen; Someya, Takao

2018-01-01

Flexible photovoltaics with extreme mechanical compliance present appealing possibilities to power Internet of Things (IoT) sensors and wearable electronic devices. Although improvement in thermal stability is essential, simultaneous achievement of high power conversion efficiency (PCE) and thermal stability in flexible organic photovoltaics (OPVs) remains challenging due to the difficulties in maintaining an optimal microstructure of the active layer under thermal stress. The insufficient thermal capability of a plastic substrate and the environmental influences cannot be fully expelled by ultrathin barrier coatings. Here, we have successfully fabricated ultraflexible OPVs with initial efficiencies of up to 10% that can endure temperatures of over 100 °C, maintaining 80% of the initial efficiency under accelerated testing conditions for over 500 hours in air. Particularly, we introduce a low-bandgap poly(benzodithiophene-cothieno[3,4-b]thiophene) (PBDTTT) donor polymer that forms a sturdy microstructure when blended with a fullerene acceptor. We demonstrate a feasible way to adhere ultraflexible OPVs onto textiles through a hot-melt process without causing severe performance degradation. PMID:29666257

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

NASA Technical Reports Server (NTRS)

Micklow, Gerald J.; Dogra, Anju S.; Nguyen, H. Lee

1990-01-01

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

NASA Astrophysics Data System (ADS)

Micklow, Gerald J.; Dogra, Anju S.; Nguyen, H. Lee

1990-07-01

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Effect of vane twist on the performance of dome swirlers for gas turbine airblast atomizers

NASA Astrophysics Data System (ADS)

Micklow, Gerald J.; Dogra, Anju S.; Nguyen, H. Lee

1990-06-01

For advanced gas turbine engines, two combustor systems, the lean premixed/prevaporized (LPP) and the rich burn/quick quench/lean burn (RQL) offer great potential for reducing NO(x) emissions. An important consideration for either concept is the development of an advanced fuel injection system that will provide a stable, efficient, and very uniform combustion system over a wide operating range. High-shear airblast fuel injectors for gas turbine combustors have exhibited superior atomization and mixing compared with pressure-atomizing fuel injectors. This improved mixing has lowered NO(x) emissions and the pattern factor, and has enabled combustors to alternate fuels while maintaining a stable, efficient combustion system. The performance of high-shear airblast fuel injectors is highly dependent on the design of the dome swirl vanes. The type of swirl vanes most widely used in gas turbine combustors are usually flat for ease of manufacture, but vanes with curvature will, in general, give superior aerodynamic performance. The design and performance of high-turning, low-loss curved dome swirl vanes with twist along the span are investigated. The twist induces a secondary vortex flow pattern which will improve the atomization of the fuel, thereby producing a more uniform fuel-air distribution. This uniform distribution will increase combustion efficiency while lowering NO(x) emissions. A systematic swirl vane design system is presented based on one-, two-, and three-dimensional flowfield calculations, with variations in vane-turning angle, rate of turning, vane solidity, and vane twist as design parameters.

Exercise countermeasures for bed-rest deconditioning

NASA Technical Reports Server (NTRS)

Greenleaf, John (Editor)

1993-01-01

The purpose for this 30-day bed rest study was to investigate the effects of short-term, high intensity isotonic and isokinetic exercise training on maintenance of working capacity (peak oxygen uptake), muscular strength and endurance, and on orthostatic tolerance, posture and gait. Other data were collected on muscle atrophy, bone mineralization and density, endocrine analyses concerning vasoactivity and fluid-electrolyte balance, muscle intermediary metabolism, and on performance and mood of the subjects. It was concluded that: The subjects maintained a relatively stable mood, high morale, and high esprit de corps throughout the study. Performance improved in nearly all tests in almost all the subjects. Isotonic training, as opposed to isokinetic exercise training, was associated more with decreasing levels of psychological tension, concentration, and motivation; and improvement in the quality of sleep. Working capacity (peak oxygen uptake) was maintained during bed rest with isotonic exercise training; it was not maintained with isokinetic or no exercise training. In general, there was no significant decrease in strength or endurance of arm or leg muscles during bed rest, in spite of some reduction in muscle size (atrophy) of some leg muscles. There was no effect of isotonic exercise training on orthostasis, since tilt-table tolerance was reduced similarly in all three groups following bed rest. Bed rest resulted in significant decreases of postural stability and self-selected step length, stride length, and walking velocity, which were not influenced by either exercise training regimen. Most pre-bed rest responses were restored by the fourth day of recovery.

Performance and bacterial community structure of a 10-years old constructed mangrove wetland.

PubMed

Tian, Tingting; Tam, Nora F Y; Zan, Qijie; Cheung, S G; Shin, Paul K S; Wong, Y S; Zhang, Li; Chen, Zhanghe

2017-11-30

Constructed mangrove wetland has been used for wastewater treatment but its long-term performance has not been reported. One-year monitoring of a 10-years old horizontal subsurface-flow constructed mangrove wetland consisting of three belts, two with mangrove plants and one without, revealed that the system maintained high and stable removal percentages of organic matter and nutrients, and planted belts performed better than unplanted control. Substrates in belts planted with Aegiceras corniculatum or Kandelia obovata had higher abundance of ammonifiers, nitrifiers and denitrifiers but lower total heterotrophic bacteria than unplanted substrate. Denaturing gradient gel electrophoresis showed that microbial diversity in planted substrate was significantly lower than that in unplanted one. The bacteria in substrates, irrespective to belts, were phylogenetically related to Proteobacteria (most dominant), Acidobacteria, Firmicutes, Nitrospirae, Gemmatimonadetes, Chloroflexi and Cyanobacteria. The steady performance of this 10-year old constructed mangrove wetland was affected by the abundance and diversity of bacterial community in substrate. Copyright © 2017 Elsevier Ltd. All rights reserved.

Switchable single-longitudinal-mode dual-wavelength erbium-doped fiber ring laser based on one polarization-maintaining fiber Bragg grating incorporating saturable absorber and feedback fiber loop

NASA Astrophysics Data System (ADS)

Feng, Suchun; Xu, Ou; Lu, Shaohua; Ning, Tigang; Jian, Shuisheng

2009-06-01

Switchable single-longitudinal-mode (SLM) dual-wavelength erbium-doped fiber ring laser based on one polarization-maintaining fiber Bragg grating (PMFBG) is demonstrated. Due to the enhancement of the polarization hole burning (PHB) by the PMFBG, the laser can be designed to operate in stable dual-wavelength or wavelength-switching modes with a wavelength spacing of 0.336 nm at room temperature by adjusting a polarization controller (PC). The stable SLM operation is guaranteed by a compound-ring cavity and a saturable absorber (SA). The optical signal-to-noise ratio (OSNR) is over 45 dB. The amplitude variation in nearly one and half an hour is less than 0.2 dB.

Stable long-term indigo production by overexpression of dioxygenase genes using a chromosomal integrated cascade expression circuit.

PubMed

Royo, Jose Luis; Moreno-Ruiz, Emilia; Cebolla, Angel; Santero, Eduardo

2005-03-16

In our laboratory we have analyzed different factors to maximize the yield in heterologous protein expression for long-term cultivation, by combination of an efficient cascade expression system and stable integration in the bacterial chromosome. In this work, we have explored this system for the production of indigo dye as a model for biotechnological production, by expressing in Escherichia coli the thnA1A2A3A4 genes from Sphingomonas macrogolitabida strain TFA, which encode the components of a tetralin dioxygenase activity. We compared Ptac, and the Pm-based cascade expression circuit in a multicopy plasmid and stably integrated into the bacterial chromosome. Plasmid-based expression systems resulted in instability of indigo production when serially diluted batch experiments were performed without a selective pressure. This problem was solved by integrating the expression module in the chromosome. Despite the gene dosage reduction, the synergic effect of the cascade expression system produced comparable expression to the dioxygenase activity in the plasmid configuration but could be stably maintained for at least 5 days. Here, we show that the cascade amplification circuit integrated in the chromosome could be an excellent system for tight control and stable production of recombinant products.

Energy Efficient and Stable Weight Based Clustering for Mobile Ad Hoc Networks

NASA Astrophysics Data System (ADS)

Bouk, Safdar H.; Sasase, Iwao

Recently several weighted clustering algorithms have been proposed, however, to the best of our knowledge; there is none that propagates weights to other nodes without weight message for leader election, normalizes node parameters and considers neighboring node parameters to calculate node weights. In this paper, we propose an Energy Efficient and Stable Weight Based Clustering (EE-SWBC) algorithm that elects cluster heads without sending any additional weight message. It propagates node parameters to its neighbors through neighbor discovery message (HELLO Message) and stores these parameters in neighborhood list. Each node normalizes parameters and efficiently calculates its own weight and the weights of neighboring nodes from that neighborhood table using Grey Decision Method (GDM). GDM finds the ideal solution (best node parameters in neighborhood list) and calculates node weights in comparison to the ideal solution. The node(s) with maximum weight (parameters closer to the ideal solution) are elected as cluster heads. In result, EE-SWBC fairly selects potential nodes with parameters closer to ideal solution with less overhead. Different performance metrics of EE-SWBC and Distributed Weighted Clustering Algorithm (DWCA) are compared through simulations. The simulation results show that EE-SWBC maintains fewer average numbers of stable clusters with minimum overhead, less energy consumption and fewer changes in cluster structure within network compared to DWCA.

Production of stable, non-thermal atmospheric pressure rf capacitive plasmas using gases other than helium or neon

DOEpatents

Park, Jaeyoung; Henins, Ivars

2005-06-21

The present invention enables the production of stable, steady state, non-thermal atmospheric pressure rf capacitive .alpha.-mode plasmas using gases other than helium and neon. In particular, the current invention generates and maintains stable, steady-state, non-thermal atmospheric pressure rf .alpha.-mode plasmas using pure argon or argon with reactive gas mixtures, pure oxygen or air. By replacing rare and expensive helium with more readily available gases, this invention makes it more economical to use atmospheric pressure rf .alpha.-mode plasmas for various materials processing applications.

Radiation-grafted fluoropolymers soaked with imidazolium-based ionic liquids for high-performance ionic polymer-metal composite actuators.

PubMed

Lee, Jang Yeol; Wang, Hyuck Sik; Yoon, Bye Ri; Han, Man Jae; Jho, Jae Young

2010-11-01

On purpose to develop a polymer actuator with high stability in air-operation as well as large bending displacement, a series of ionic polymer-metal composites (IPMC) was constructed with poly(styrene sulfonate)-grafted fluoropolymers as ionomeric matrix and immidazolium-based ionic liquids (IL) as inner solvent. The prepared IPMC actuators exhibited greatly enhanced bending displacement compared to Nafion-based actuators. The actuators were stable in air-operation, maintaining initial displacement for up to 10(4) cycles or 24 h. Investigating the material parameters and morphology of the IPMCs, high ion exchange capacity of the ionomers resulted in high ion conductivity and robust electrode of IPMC, which synergistically contributed to the high bending performance. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Micromold methods for fabricating perforated substrates and for preparing solid polymer electrolyte composite membranes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mittelsteadt, Cortney; Argun, Avni; Laicer, Castro

In polymer electrolyte membrane (PEM) fuel cells and electrolyzes, attaining and maintaining high membrane conductivity and durability is crucial for performance and efficiency. The use of low equivalent weight (EW) perfluorinated ionomers is one of the few options available to improve membrane conductivity. However, excessive dimensional changes of low EW ionomers upon application of wet/dry or freeze/thaw cycles yield catastrophic losses in membrane integrity. Incorporation of ionomers within porous, dimensionally-stable perforated polymer electrolyte membrane substrates provides improved PEM performance and longevity. The present invention provides novel methods using micromolds to fabricate the perforated polymer electrolyte membrane substrates. These novel methodsmore » using micromolds create uniform and well-defined pore structures. In addition, these novel methods using micromolds described herein may be used in batch or continuous processing.« less

Within-farm variability in age structure of breeding-female pigs and reproductive performance on commercial swine breeding farms.

PubMed

Koketsu, Yuzo

2005-03-15

This study investigated relationships between herd age structure and herd productivity in breeding herds; it also investigated a pattern in parity proportions of females over 2 years and its relationship with herd productivity in commercial swine herds. This study was based on data from 148 commercial farms in North America stored in the swine database program at the University of Minnesota. The primary selection criterion was fluctuations in breeding-female pig (female) inventories over a 2-year interval. Productivity measurements and parity proportions of females were extracted from the database. A 24-month time-plot in proportions of Parity 0 and Parities 3-5 females (mid-parity) was charted for each farm. Using these charts, a change in proportions of Parity 0 and mid-parity for each farm was categorized into patterns: FLUCTUATE (Parity 0 and mid-parity proportion lines crossed) or STABLE (the two proportion lines never crossed). Higher proportions of mid-parity sows were correlated with greater pigs weaned per female per year (PWFY; P < 0.01). Farms with a FLUCTUATE (73% of the 148 farms) pattern had lower PWFY than those with a STABLE pattern (P < 0.01). The STABLE farms had higher proportions of mid-parity sows, higher parity at culling, higher frequency of gilt deliveries per year, and lower replacement rate than the FLUCTUATE farms (P < 0.01). In conclusion, maintaining stable subpopulations with mid-parity and Parity 0 are recommended to optimize herd productivity.

Culturing Protozoa.

ERIC Educational Resources Information Center

Stevenson, Paul

1980-01-01

Compares various nutrient media, growth conditions, and stock solutions used in culturing protozoa. A hay infusion in Chalkey's solution maintained at a stable temperature is recommended for producing the most dense and diverse cultures. (WB)

Rational design of Fe3O4@C yolk-shell nanorods constituting a stable anode for high-performance Li/Na-ion batteries.

PubMed

Wang, Beibei; Zhang, Xing; Liu, Xiaojie; Wang, Gang; Wang, Hui; Bai, Jintao

2018-05-24

In the current research project, we have prepared a novel Fe 3 O 4 @mesoporous carbon nanorod (denoted as Fe 3 O 4 @C) anode with yolk-shell structure for Li/Na-ion batteries via one-pot and surfactant-free synthesis strategy. The yolk-shell structure consists of Fe 3 O 4 nanorod yolk completely protected by a well-conductive mesoporous carbon shell. The substantial void space in the Fe 3 O 4 @C yolk-shell nanorod can not only accommodate the full volume expansion of inner Fe 3 O 4 nanorod, but also preserve the structural integrity of the Fe 3 O 4 @C anode and develop a stable SEI film on the outside mesoporous carbon shell during the repeated Li + /Na + insertion/extraction processes. As for lithium storage, the Fe 3 O 4 @C electrode exhibits a high specific capacity (1247 mAh g -1 ), stable cycling performance (a specific capacity of 954 mAh g -1 after 200 cycles at a current density of 0.5 A g -1 ) and excellent rate capability (specific capabilities of 1122, 958, 783, 577, and 374 mAh g -1 at 0.5, 1, 2, 4, and 8 A g -1 , respectively). As for sodium storage, the Fe 3 O 4 @C yolk-shell nanorods also maintain a reversible capacity of approximate 424 mAh g -1 at 0.1 A g -1 after 100 cycles. Copyright © 2018. Published by Elsevier Inc.

Periodontist-Dental Hygienist Collaboration in Periodontal Care for Chronic Periodontitis: An 11-year Case Report.

PubMed

Tomita, Sachiyo; Uekusa, Tomomi; Hosono, Meiko; Kigure, Takashi; Sugito, Hiroki; Saito, Atsushi

2016-01-01

We report a case of severe chronic periodontitis treated and longitudinally maintained by a periodontist and dental hygienists. The patient was a 45-year-old woman who presented with the chief complaint of gingival bleeding and tooth mobility. An initial examination revealed generalized gingival inflammation and subgingival calculus in the premolar and molar regions. Premature contact was observed in #14 and 45. Clinical examination revealed 42% of sites with a probing depth (PD) of ≥4 mm and 44% of sites with bleeding on probing. Radiographic examination revealed vertical bone resorption in #35, 36, and 45, and horizontal bone resorption in other regions. Based on a clinical diagnosis of severe chronic periodontitis, initial periodontal therapy consisting of plaque control, scaling and root planing, and removal of an ill-fitting prosthesis was performed. Following suppression of inflammation, occlusal adjustment of premature contact sites was performed. Open flap debridement was performed for teeth with a PD of ≥5 mm. After confirming the stability of the periodontal tissue, final prostheses were placed on #16, 35-37, and 46. Following re-evaluation, the patient was placed on supportive periodontal therapy. It has been 11 years since the patient's first visit, and the periodontal conditions have remained stable. Meticulous periodontal care maintained over a number of years by a periodontist and dental hygienist have yielded a clinically favorable outcome.

All-solid state symmetric supercapacitors based on compressible and flexible free-standing 3D carbon nanotubes (CNTs)/poly(3,4-ethylenedioxythiophene) (PEDOT) sponge electrodes

NASA Astrophysics Data System (ADS)

He, Xin; Yang, Wenyao; Mao, Xiling; Xu, Lu; Zhou, Yujiu; Chen, Yan; Zhao, Yuetao; Yang, Yajie; Xu, Jianhua

2018-02-01

Flexible supercapacitors that maintain electrochemical performance under deformation have attracted much attention for the potential application in the flexible electronics market. A compressible and flexible free-standing electrodes sponge and all-solid-state symmetric supercapacitors based on as-prepared electrodes are presented. The carbon nanotubes (CNTs) framework is synthesized by chemical vapor deposition (CVD) method, and then composited with poly (3,4-ethylenedioxythiophene) PEDOT by the electrodeposition. This CNTs/PEDOT sponge electrode shows highest mass-specific capacitance of 147 Fg-1 at 0.5 A g-1, tuned by the PEDOT mass loading, and exhibits good cyclic stability with the evidence that more than 95% of capacitance is remained after 3000 cycles. Furthermore, the symmetric supercapacitor shows the highest energy density of 12.6 Wh kg-1 under the power density of 1 kW kg-1 and highest power density of 10.2 kW kg-1 with energy density of 8 Wh kg-1, which exhibits both high energy density and power density. The electrochemical performance of composite electrode also indicates that the operate voltage of device could be extend to 1.4 V by the n-doping and p-doping process in different potential of PEDOT component. This flexible supercapacitor maintains stable electrochemical performance working on different bending condition, which shows promising prospect for wearable energy storage applications.

Sustainable Sulfur-rich Copolymer/Graphene Composite as Lithium-Sulfur Battery Cathode with Excellent Electrochemical Performance

PubMed Central

Ghosh, Arnab; Shukla, Swapnil; Khosla, Gaganpreet Singh; Lochab, Bimlesh; Mitra, Sagar

2016-01-01

A sulfur-rich copolymer, poly(S-r-C-a) has been synthesized via a sustainable route, showing the utility of two major industrial wastes- elemental sulfur (petroleum waste) and cardanol (agro waste), to explore its potential as cathode material for Li-S batteries. The sulfur-rich copolymer exhibited a reduction in the active material dissolution into the electrolyte and a low self-discharge rate behavior during the rest time compared to an elemental sulfur cathode, indicating the chemical confinement of sulfur units. The presence of organosulfur moieties in copolymer suppress the irreversible deposition of end-discharge products on electrode surfaces and thus improve the electrochemical performances of Li-S batteries. This sulfur copolymer offered a reversible capacity of 892 mA h g−1 at 2nd cycle and maintained the capacity of 528 mA h g−1 after 50 cycles at 200 mA g−1. Reduced graphene oxide (rGO) prepared via a sustainable route was used as a conductive filler to extract the better electrochemical performances from this sulfur copolymer. Such sustainable origin batteries prepared via economically viable showed an improved specific capacity of ~975 mA h g−1 after 100 cycles at 200 mA g−1 current rate with capacity fading of 0.15% per cycle and maintained a stable performance over 500 cycles at 2000 mA g−1. PMID:27121089

A sensitive high-performance liquid chromatographic method for the determination of 6-mercaptopurine in plasma using precolumn derivatization and fluorescence detection.

PubMed

Warren, D J; Slørdal, L

1993-02-01

A sensitive high-performance liquid chromatographic (HPLC) method for measuring plasma concentrations of 6-mercaptopurine (6-MP) is described. After protein precipitation with 5-sulfosalicylic acid, samples are subjected to precolumn derivatization using the thiol-reactive fluorophore monobromobimane (mBrB). The drug-mBrB adduct is then resolved by isocratic elution from a C18 reversed-phase support and quantified by fluorescence detection. Recovery of 6-MP after protein precipitation was consistently > 85% and the drug-mBrB adduct was found to be stable for at least 2 weeks at room temperature. With plasma samples containing 30 nM 6-MP, the assay displayed within-run (n = 6) and between-day (n = 6) coefficients of variation of 2.2 and 10.6%, respectively. The limit of detection for 6-MP in plasma was 3 nM (500 pg/ml) and the standard curve was linear up to 3 microM. Using this method, we have observed that 6-MP is stable in heparinized whole blood for at least 24 h provided samples are maintained on ice. Since this method requires few manipulations during sample preparation and is readily adaptable to automated techniques, it may prove useful in the routine clinical laboratory setting.

Intrinsically Stretchable and Conductive Textile by a Scalable Process for Elastic Wearable Electronics.

PubMed

Wang, Chunya; Zhang, Mingchao; Xia, Kailun; Gong, Xueqin; Wang, Huimin; Yin, Zhe; Guan, Baolu; Zhang, Yingying

2017-04-19

The prosperous development of stretchable electronics poses a great demand on stretchable conductive materials that could maintain their electrical conductivity under tensile strain. Previously reported strategies to obtain stretchable conductors usually involve complex structure-fabricating processes or utilization of high-cost nanomaterials. It remains a great challenge to produce stretchable and conductive materials via a scalable and cost-effective process. Herein, a large-scalable pyrolysis strategy is developed for the fabrication of intrinsically stretchable and conductive textile in utilizing low-cost and mass-produced weft-knitted textiles as raw materials. Due to the intrinsic stretchability of the weft-knitted structure and the excellent mechanical and electrical properties of the as-obtained carbonized fibers, the obtained flexible and durable textile could sustain tensile strains up to 125% while keeping a stable electrical conductivity (as shown by a Modal-based textile), thus ensuring its applications in elastic electronics. For demonstration purposes, stretchable supercapacitors and wearable thermal-therapy devices that showed stable performance with the loading of tensile strains have been fabricated. Considering the simplicity and large scalability of the process, the low-cost and mass production of the raw materials, and the superior performances of the as-obtained elastic and conductive textile, this strategy would contribute to the development and industrial production of wearable electronics.

Evaluation of innovative operation concept for flat sheet MBR filtration system.

PubMed

Weinrich, L; Grélot, A

2008-01-01

One of the most limiting factors for the extension and acceptance of MBR filtration systems for municipal and industrial wastewater is the impact of membrane fouling on maintenance, operation and cleaning efforts. One field of action in the European Research Project "AMEDEUS" is the development and testing of MBR module concepts with innovative fouling-prevention technology from three European module manufacturers. This article deals with the performances of the flat-sheet modules by A3 Water Solutions GmbH in double-deck configuration evaluated over 10 months in Anjou Recherche under typical biological operation conditions for MBR systems (MLSS = 10 g/l; SRT = 25 days). By using a double-deck configuration, it is possible to operate with a net flux of 25.5 l/m2.h at 20 degrees C, a membrane air flow rate of 0.21 Nm3/h.m2 of membrane to achieve a stable permeability of around 500-600 l/m2.h.bar. Additionally, it was observed that it is possible to recover the membrane performance after biofouling during operation without intensive cleaning and to maintain stable permeability during peak flows. The evaluated concepts for equipping and operating MBR systems will be applied to several full-scale plants constructed by A3 Water Solutions GmbH.

From Coordination Cages to a Stable Crystalline Porous Hydrogen-Bonded Framework

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ju, Zhanfeng; Liu, Guoliang; Chen, Yu-Sheng

2017-03-20

A stable framework has been constructed through multiple charge-assisted H-bonds between cationic coordination cages and chloride ions. The framework maintained its original structure upon desolvation, which has been established by single-crystal structure analysis. This is the first fully characterized stable porous framework based on coordination cages after desolvation, with a moderately high Brunauer–Emmett–Teller (BET) surface area of 1201 m2 g-1. This work will not only give a light to construct stable porous frameworks based on coordination cages and thus broaden their applications, but will also provide a new avenue to the assembly of other porous materials such as porous organicmore » cages and hydrogen-bonded organic frameworks (HOFs) through non covalent bonds.« less

Implementation and Operational Research: CD4 Count Monitoring Frequency and Risk of CD4 Count Dropping Below 200 Cells Per Cubic Millimeter Among Stable HIV-Infected Patients in New York City, 2007-2013.

PubMed

Myers, Julie E; Xia, Qiang; Torian, Lucia V; Irvine, Mary; Harriman, Graham; Sepkowitz, Kent A; Shepard, Colin W

2016-03-01

The evidence has begun to mount for diminishing the frequency of CD4 count testing. To determine whether these observations were applicable to an urban US population, we used New York City (NYC) surveillance data to explore CD4 testing among stable patients in NYC, 2007-2013. We constructed a population-based retrospective open cohort analysis of NYC HIV surveillance data. HIV+ patients aged ≥ 13 years with stable viral suppression (≥ 1 viral load the previous year; all <400 copies per milliliter) and immune status (≥ 1 CD4 the previous year; all ≥ 200 cells per cubic millimeter) entered the cohort the following year beginning January 1, 2007. Each subsequent year, eligible patients not previously included entered the cohort on January 1. Outcomes were annual frequency of CD4 monitoring and probability of maintaining CD4 ≥ 200 cells per cubic millimeter. A multivariable Cox model identified factors associated with maintaining CD4 ≥ 200 cells per cubic millimeter. During 1.9 years of observation (median), 62,039 patients entered the cohort. The mean annual number of CD4 measurements among stable patients was 2.8 and varied little by year or characteristic. Two years after entering, 93.4% and 97.8% of those with initial CD4 350-499 and CD4 ≥ 500 cells per cubic millimeter, respectively, maintained CD4 ≥ 200 cells per cubic millimeter. Compared to those with initial CD4 ≥ 500 cells per cubic millimeter, those with CD4 200-349 cells per cubic millimeter and CD4 350-499 cells per cubic millimeter were more likely to have a CD4 <200 cells per cubic millimeter, controlling for sex, race, age, HIV risk group, and diagnosis year. In a population-based US cohort with well-controlled HIV, the probability of maintaining CD4 ≥ 200 cells per cubic millimeter for ≥ 2 years was >90% among those with initial CD4 ≥ 350 cells per cubic millimeter, suggesting that limited CD4 monitoring in these patients is appropriate.

Multidigit force control during unconstrained grasping in response to object perturbations

PubMed Central

Haschke, Robert; Ritter, Helge; Santello, Marco; Ernst, Marc O.

2017-01-01

Because of the complex anatomy of the human hand, in the absence of external constraints, a large number of postures and force combinations can be used to attain a stable grasp. Motor synergies provide a viable strategy to solve this problem of motor redundancy. In this study, we exploited the technical advantages of an innovative sensorized object to study unconstrained hand grasping within the theoretical framework of motor synergies. Participants were required to grasp, lift, and hold the sensorized object. During the holding phase, we repetitively applied external disturbance forces and torques and recorded the spatiotemporal distribution of grip forces produced by each digit. We found that the time to reach the maximum grip force during each perturbation was roughly equal across fingers, consistent with a synchronous, synergistic stiffening across digits. We further evaluated this hypothesis by comparing the force distribution of human grasping vs. robotic grasping, where the control strategy was set by the experimenter. We controlled the global hand stiffness of the robotic hand and found that this control algorithm produced a force pattern qualitatively similar to human grasping performance. Our results suggest that the nervous system uses a default whole hand synergistic control to maintain a stable grasp regardless of the number of digits involved in the task, their position on the objects, and the type and frequency of external perturbations. NEW & NOTEWORTHY We studied hand grasping using a sensorized object allowing unconstrained finger placement. During object perturbation, the time to reach the peak force was roughly equal across fingers, consistently with a synergistic stiffening across fingers. Force distribution of a robotic grasping hand, where the control algorithm is based on global hand stiffness, was qualitatively similar to human grasping. This suggests that the central nervous system uses a default whole hand synergistic control to maintain a stable grasp. PMID:28228582

Successful prolonged ex vivo lung perfusion for graft preservation in rats.

PubMed

Noda, Kentaro; Shigemura, Norihisa; Tanaka, Yugo; Bhama, Jay K; D'Cunha, Jonathan; Luketich, James D; Bermudez, Christian A

2014-03-01

Ex vivo lung perfusion (EVLP) strategies represent a new frontier in lung transplantation technology, and there have been many clinical studies of EVLP in lung transplantation. The establishment of a reliable EVLP model in small animals is crucial to facilitating translational research using an EVLP strategy. The main objective of this study was to develop a reproducible rat EVLP (R-EVLP) model that enables prolonged evaluation of the explanted lung during EVLP and successful transplantation after EVLP. The donor heart-lung blocks were procured with cold low-potassium dextran solution and immersed in the solution for 1 h at 4 °C. And then, the heart-lung blocks were flushed retrogradely and warmed up to 37 °C in a circuit perfused antegradely with acellular perfusate. The perfusate was deoxygenated with a gas mixture (6% O2, 8% CO2, 86% N2). The perfusion flow was maintained at 20% of the entire cardiac output. At 37 °C, the lungs were mechanically ventilated and perfusion continued for 4 h. Every hour, the perfused lung was evaluated for gas exchange, dynamic lung compliance (Cdyn) and pulmonary vascular resistance (PVR). R-EVLP was performed for 4 h. Pulmonary oxygenation ability (pO2/pCO2) was stable for 4 h during EVLP. It was noted that Cdyn and PVR were also stable. After 4 h of EVLP, pO2 was 303 ± 19 mmHg, pCO2 was 39.6 ± 1.2 mmHg, PVR was 1.75 ± 0.10 mmHg/ml/min and Cdyn was 0.37 ± 0.03 ml/cmH2O. Lungs that were transplanted after 2 h of R-EVLP resulted in significantly better post-transplant oxygenation and compliance when compared with those after standard cold static preservation. Our R-EVLP model maintained stable lung oxygenation, compliance and vascular resistance for up to 4 h of perfusion duration. This reliable model should facilitate further advancement of experimental work using EVLP.

Nickel-foam-supported ruthenium oxide/graphene sandwich composite constructed via one-step electrodeposition route for high-performance aqueous supercapacitors

NASA Astrophysics Data System (ADS)

Li, Meng; He, Hanwei

2018-05-01

A high-performance supercapacitor both considered high power and high energy density is needed for its applications such as portable electronics and electric vehicles. Herein, we construct a high-performance ruthenium oxide/graphene (RuO2-ERG) composite directly grown on Ni foam through cyclic voltammetric deposition process. The RuO2-ERG composite with sandwich structure is achieved effectively from a mixed solution of graphene oxide and ruthenium trichloride in the -1.4 V to 1.0 V potential range at a scan rate of 5 mV s-1. The electrochemical performance is optimized by tuning the concentration of the ruthenium trichloride. This integrative RuO2-ERG composite electrode can effectively maintains the accessible surface for redox reaction and stable channels for electrolyte penetration, leading to an improved electrochemical performance. Symmetrical aqueous supercapacitors based on RuO2-ERG electrodes exhibit a wider operational voltage window of 1.5 V. The optimized RuO2-ERG electrode displays a superior specific capacitance with 89% capacitance retention upon increasing the current density by 50 times. A high energy density of 43.8 W h kg-1 at a power density of 0.75 kW kg-1 is also obtained, and as high as 39.1 W h kg-1 can be retained at a power density of 37.5 kW kg-1. In addition, the capacitance retention is still maintained at 92.8% even after 10,000 cycles. The excellent electrochemical performance, long-term cycle stability, and the ease of preparation demonstrate that this typical RuO2-ERG electrode has great potentialities to develop high-performance supercapacitors.

New Design for an Adjustable Cise Space Maintainer

PubMed Central

2018-01-01

Objective The aim of this study is to present a new adjustable Cise space maintainer for preventive orthodontic applications. Methods Stainless steel based new design consists of six main components. In order to understand the major displacement and stress fields, structural analysis for the design is considered by using finite element method. Results Similar to major displacement at y-axis, critical stresses σx and τxy possess a linear distribution with constant increasing. Additionally, strain energy density (SED) plays an important role to determine critical biting load capacity. Conclusion Structural analysis shows that the space maintainer is stable and is used for maintaining and/or regaining the space which arouses early loss of molar tooth. PMID:29854764

Understanding the role of nonlinearities in the transduction of vibratory energy harvesters

NASA Astrophysics Data System (ADS)

Masana, Ravindra Shiva Charan

The last two decades have witnessed several advances in micro-fabrication technologies and electronics, leading to the development of small, low-power devices for wireless sensing, data transmission, actuation, and medical implants. Unfortunately, the actual implementation of such devices in their respective environment has been hindered by the lack of scalable energy sources that are necessary to power and maintain them. Batteries, which remain the most commonly used power source, have not kept pace with the demands of these devices, especially in terms of energy density. In light of this challenge, the concept of vibratory energy harvesting has flourished in recent years as a possible alternative to power and maintain low-power electronics. While linear vibratory energy harvesters have received the majority of the literature's attention, a significant body of the current research activity is focused on the concept of purposeful inclusion of nonlinearities for broadband transduction. When compared to their linear resonant counterparts, nonlinear energy harvesters have a wider steady-state frequency bandwidth, leading to the common belief that they can be utilized to improve performance especially in random and non-stationary vibratory environments. This dissertation aims to critically investigate this belief by drawing a clearer picture of the role of nonlinearities in the transduction of energy harvesters and by defining the conditions under which nonlinearities can be used to enhance performance. To achieve this goal, the Thesis is divided into three parts. The first part investigates the performance of mono- and bi-stable energy harvesters under harmonic excitations and carries a detailed analysis of their relative performance. The second part investigates their response to broadband and narrowband random excitations and again analyzes their relative behavior. The third part exploits the super-harmonic resonance bands of bi-stable energy harvesters for the purpose of scavenging energy from low-frequency excitations. As a platform to achieve the Thesis objectives, a piezoelectric energy harvester consisting of an axially loaded clamped-clamped beam bi-morph is considered. The harvester can operate with mono- (pre-buckling) and bi-stable (post-buckling) characteristics with minimal alterations to the design. Theoretical and experimental studies performed on the proposed harvester are presented to delineate the influence of the nonlinearity on its performance, in particular, and nonlinear vibratory energy harvesters in general. It is demonstrated that the intentional inclusion of nonlinearities in energy harvesters makes these devices more tolerant to variations in the excitation and design parameters around their nominal values as compared to a linear device. However, the Thesis also pointed out many issues that can result from the complexity and non-uniqueness of solutions associated with nonlinear systems. It became apparent that the performance of a nonlinear energy harvester is very much dependent on the level and nature of the excitation in conjunction with the potential shape of the harvester. This makes developing direct performance metrics, similar to what has been done for linear harvesters, a challenging problem which should constitute a major avenue of future research efforts.

Fine pointing control for free-space optical communication

NASA Technical Reports Server (NTRS)

Portillo, A. A.; Ortiz, G. G.; Racho, C.

2000-01-01

Free-Space Optical Communications requires precise, stable laser pointing to maintain operating conditions. This paper also describes the software and hardware implementation of Fine Pointing Control based on the Optical Communications Demonstrator architecture.

The binding of histone deacetylases and the integrity of zinc finger-like motifs of the E7 protein are essential for the life cycle of human papillomavirus type 31.

PubMed

Longworth, Michelle S; Laimins, Laimonis A

2004-04-01

The E7 oncoprotein of high-risk human papillomaviruses (HPVs) binds to and alters the action of cell cycle regulatory proteins such as members of the retinoblastoma (Rb) family of proteins as well as the histone deacetylases (HDACs). To examine the significance of the binding of E7 to HDACs in the viral life cycle, a mutational analysis of the E7 open reading frame was performed in the context of the complete HPV type 31 (HPV-31) genome. Human foreskin keratinocytes were transfected with wild-type HPV-31 genomes or HPV-31 genomes containing mutations in HDAC binding sequences as well as in the C-terminal zinc finger-like domain, and stable cell lines were isolated. All mutant genomes, except those with E7 mutations in the HDAC binding site, were found to be stably maintained extrachromosomally at an early passage following transfection. Upon further passage in culture, genomes containing mutations to the Rb binding domain as well as the zinc finger-like region quickly lost the ability to maintain episomal genomes. Genomes containing mutations abolishing E7 binding to HDACs or to Rb or mutations to the zinc finger-like motifs failed to extend the life span of transfected keratinocytes and caused cells to arrest at the same time as the untransfected keratinocytes. When induced to differentiate by suspension in methylcellulose, cells maintaining genomes with mutations in the Rb binding domain or the zinc finger-like motifs were impaired in their abilities to activate late viral functions. This study demonstrates that the interaction of E7 with HDACs and the integrity of the zinc finger-like motifs are essential for extending the life span of keratinocytes and for stable maintenance of viral genomes.

Stability of Hydromorphone-Ketamine Solutions in Glass Bottles, Plastic Syringes, and IV Bags for Pediatric Use.

PubMed

Ensom, Mary H H; Decarie, Diane; Leung, Karen; Montgomery, Carolyne

2009-03-01

To evaluate the stability of mixtures of hydromorphone and ketamine in 0.9% sodium chloride (normal saline [NS]) after storage for up to 7 days at room temperature (25°C). The stability of 3 standard mixtures of hydromorphone and ketamine (hydromorphone 0.2 mg/mL + ketamine 0.2 mg/mL, hydromorphone 0.2 mg/mL + ketamine 0.6 mg/mL, and hydromorphone 0.2 mg/mL + ketamine 1.0 mg/mL) in NS was studied. Portions of each mixture were transferred to 3 brown glass bottles (100 mL), 3 plastic syringes (50 mL), and 3 IV bags (50 mL), which were then stored at room temperature (25°C). Physical characteristics, including pH, colour, and precipitation, were evaluated daily. Three 1.5-mL samples were collected from each bottle, syringe, and IV bag at baseline, at 24, 48, and 72 hours, and on day 7. Samples were analyzed in triplicate by a stability-indicating high-performance liquid chromatography method. Solutions were considered stable if they maintained 90% of the initial concentration of each drug. Samples from syringes and IV bags were subjected to standard sterility testing by incubation for 5 days in an enriched culture media. No notable changes in pH or colour were observed, and no precipitation occurred in any of the solutions. All formulations maintained more than 90% of the initial concentration of each drug on day 7. No bacterial growth was observed in any of the samples tested. Mixtures of hydromorphone and ketamine were stable for up 7 days at 25°C, and the sterility of the preparations was maintained. Because stability alone does not guarantee efficacy, it is recommended that clinical studies be conducted to evaluate the pharmacokinetics and pharmacodynamics of these formulations.

Continuous high-solids anaerobic co-digestion of organic solid wastes under mesophilic conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Dong-Hoon; Oh, Sae-Eun, E-mail: saeun@hanbat.ac.kr

2011-09-15

Highlights: > High-solids (dry) anaerobic digestion is attracting a lot of attention these days. > One reactor was fed with food waste (FW) and paper waste. > Maximum biogas production rate of 5.0 m{sup 3}/m{sup 3}/d was achieved at HRT 40 d and 40% TS. > The other reactor was fed with FW and livestock waste (LW). > Until a 40% LW content increase, the reactor exhibited a stable performance. - Abstract: With increasing concerns over the limited capacity of landfills, conservation of resources, and reduction of CO{sub 2} emissions, high-solids (dry) anaerobic digestion of organic solid waste (OSW) ismore » attracting a great deal of attention these days. In the present work, two dry anaerobic co-digestion systems fed with different mixtures of OSW were continuously operated under mesophilic conditions. Dewatered sludge cake was used as a main seeding source. In reactor (I), which was fed with food waste (FW) and paper waste (PW), hydraulic retention time (HRT) and solid content were controlled to find the maximum treatability. At a fixed solid content of 30% total solids (TS), stable performance was maintained up to an HRT decrease to 40 d. However, the stable performance was not sustained at 30 d HRT, and hence, HRT was increased to 40 d again. In further operation, instead of decreasing HRT, solid content was increased to 40% TS, which was found to be a better option to increase the treatability. The biogas production rate (BPR), CH{sub 4} production yield (MPY) and VS reduction achieved in this condition were 5.0 m{sup 3}/m{sup 3}/d, 0.25 m{sup 3} CH{sub 4}/g COD{sub added}, and 80%, respectively. Reactor (II) was fed with FW and livestock waste (LW), and LW content was increased during the operation. Until a 40% LW content increase, reactor (II) exhibited a stable performance. A BPR of 1.7 m{sup 3}/m{sup 3}/d, MPY of 0.26 m{sup 3} CH{sub 4}/g COD{sub added}, and VS reduction of 72% was achieved at 40% LW content. However, when the LW content was increased to 60%, there was a significant performance drop, which was attributed to free ammonia inhibition. The performances in these two reactors were comparable to the ones achieved in the conventional wet digestion and thermophilic dry digestion processes.« less

Flexible Fe3O4@Carbon Nanofibers Hierarchically Assembled with MnO2 Particles for High-Performance Supercapacitor Electrodes.

PubMed

Iqbal, Nousheen; Wang, Xianfeng; Babar, Aijaz Ahmed; Zainab, Ghazala; Yu, Jianyong; Ding, Bin

2017-11-09

Increasing use of wearable electronic devices have resulted in enhanced demand for highly flexible supercapacitor electrodes with superior electrochemical performance. In this study, flexible composite membranes with electrosprayed MnO 2 particles uniformly anchored on Fe 3 O 4 doped electrospun carbon nanofibers (Fe 3 O 4 @CNF Mn ) have been prepared as flexible electrodes for high-performance supercapacitors. The interconnected porous beaded structure ensures free movement of electrolyte within the composite membranes, therefore, the developed supercapacitor electrodes not only offer high specific capacitance of ~306 F/g, but also exhibit good capacitance retention of ~85% after 2000 cycles, which certify that the synthesized electrodes offer high and stable electrochemical performance. Additionally, the supercapacitors fabricated from our developed electrodes well maintain their performance under flexural stress and exhibit a very minute change in specific capacitance even up to 180° bending angle. The developed electrode fabrication strategy integrating electrospinning and electrospray techniques paves new insights into the development of potential functional nanofibrous materials for light weight and flexible wearable supercapacitors.

Tactility as a function of grasp force: Effects of glove, orientation, pressure, load, and handle

NASA Technical Reports Server (NTRS)

Bishu, Ram R.; Bronkema, Lisa A.; Garcia, Dishayne; Klute, Glenn; Rajulu, Sudhakar

1994-01-01

One of the reasons for reduction in performance when gloves are donned is the lack of tactile sensitivity. It was argued that grasping force for a weight to be grasped will be a function of the weight to be lifted and the hand conditions. It was further reasoned that the differences in grasping force for various hand conditions will be a correlate of the tactile sensitivity of the corresponding hand conditions. The objective of this experiment, therefore, was to determine the effects of glove type, pressure, and weight of load on the initial grasping force and stable grasping force. It was hypothesized that when a person grasps an object, he/she grasps very firmly initially and then releases the grasp slightly after realizing what force is needed to maintain a steady grasp. This would seem to be particularly true when a person is wearing a glove and has lost some tactile sensitivity and force feedback during the grasp. Therefore, the ratio of initial force and stable force and the stable force itself would represent the amount of tactile adjustment that is made when picking up an object, and this adjustment should vary with the use of gloves. A dynamometer was fabricated to measure the grasping force; the tests were performed inside a glove box. Four female and four male subjects participated in the study, which measured the effects of four variables: load effect, gender effect, glove type, and pressure variance. The only significant effects on the peak and stable force were caused by gender and the weight of the load lifted. Neither gloves nor pressure altered these forces when compared to a bare-handed condition, as was suspected before the test. It is possible that gloves facilitate in holding due to coefficient of friction while they deter in peak grasp strength.

Functional integrity of flexible n-channel metal-oxide-semiconductor field-effect transistors on a reversibly bistable platform

NASA Astrophysics Data System (ADS)

Alfaraj, Nasir; Hussain, Aftab M.; Torres Sevilla, Galo A.; Ghoneim, Mohamed T.; Rojas, Jhonathan P.; Aljedaani, Abdulrahman B.; Hussain, Muhammad M.

2015-10-01

Flexibility can bring a new dimension to state-of-the-art electronics, such as rollable displays and integrated circuit systems being transformed into more powerful resources. Flexible electronics are typically hosted on polymeric substrates. Such substrates can be bent and rolled up, but cannot be independently fixed at the rigid perpendicular position necessary to realize rollable display-integrated gadgets and electronics. A reversibly bistable material can assume two stable states in a reversible way: flexibly rolled state and independently unbent state. Such materials are used in cycling and biking safety wristbands and a variety of ankle bracelets for orthopedic healthcare. They are often wrapped around an object with high impulsive force loading. Here, we study the effects of cumulative impulsive force loading on thinned (25 μm) flexible silicon-based n-channel metal-oxide-semiconductor field-effect transistor devices housed on a reversibly bistable flexible platform. We found that the transistors have maintained their high performance level up to an accumulated 180 kN of impact force loading. The gate dielectric layers have maintained their reliability, which is evidenced by the low leakage current densities. Also, we observed low variation in the effective electron mobility values, which manifests that the device channels have maintained their carrier transport properties.

Mixed-Potential NO x and NH 3 Sensors Fabricated by Commercial Manufacturing Methods [Mixed-Potential Sensors NO x and NH 3 Fabricated by Commercial Manufacturing Methods

DOE PAGES

Kreller, Cortney R.; Spernjak, Dusan; Li, Wenxia; ...

2014-08-12

Meeting EPA Tier 3 emissions reduction requirements while simultaneously increasing fuel economy to meet new CAFE standards will require optimization of advanced combustion strategies and emissions control technologies. There is an immediate need for suitable exhaust gas sensor technologies to monitor internal combustion engine tailpipe emissions and to control and maintain efficient operation of the engine and exhaust after treatment systems. NH 3, NO x, and HC sensors could enable onboard diagnostics and combustion control in lean-burn engines, analogous to the role of O 2 sensors in stoichiometric burn engines. Commercial manufacturing methods have been used to fabricate self-heated mixed-potentialmore » sensors in a planar automotive configuration. By altering materials composition and operating conditions, we are able to obtain sensitivity/selectivity to each NH 3, NO x and HCs. In addition, these devices exhibit stable performance over months of testing as a result of the stable morphology of the electrode/electrolyte/gas three-phase interface.« less

Hybrid MF and membrane bioreactor process applied towards water and indigo reuse from denim textile wastewater.

PubMed

Couto, Carolina Fonseca; Marques, Larissa Silva; Balmant, Janine; de Oliveira Maia, Andreza Penido; Moravia, Wagner Guadagnin; Santos Amaral, Miriam Cristina

2018-03-01

This work investigates the application of a microfiltration (MF)-membrane bioreactor (MBR) hybrid process for textile dyeing process wastewater reclamation. The indigo blue dye was efficiently retained by the MF membrane (100%), which allows its recovery from the concentrate stream. MF promotes 100% of colour removal, and reduces the chemical oxygen demand (COD) and conductivity by about 65% and 25%, respectively, and improves the wastewater biodegradability. MF flux decline was mostly attributed to concentration polarization and the chemical cleaning was efficient enough to recover initial hydraulic resistance. The MBR provides to be a stable process maintaining its COD and ammonia removal efficiency (73% and 100%, respectively) mostly constant throughout and producing a permeate that meets the reuse criteria for some industry activities, such as washing-off and equipment washdown. The use of an MF or ultrafiltration (UF) membrane in the MBR does not impact the MBR performance in terms of COD removal. Although the membrane of MBR-UF shows permeability lower than MBR-MF membrane, the UF membrane contributes to a more stable operation in terms of permeability.

Experimental and simulation studies of hard contact in force reflecting teleoperation

NASA Technical Reports Server (NTRS)

Hannaford, Blake; Anderson, Robert

1988-01-01

Experiments and simulations of a single-axis force-reflecting teleoperation system have been conducted to investigate the problem of contacting a hard environment and maintaining a controlled force in teleoperation in which position is fed forward from the hand controller (master) to the manipulator (slave), and force is fed back to the human operator through motors in the master. The simulations, using an electrical circuit model, reproduce the behavior of the real system, including effects of human operator biomechanics. It is shown that human operator properties, which vary as a result of different types of grasp of the handle, affect the stability of the system in the hard-contact task. The effect of a heavier grasp on the handle is equivalent to increased hand-controller velocity damping in terms of the systems stability in the contact task, but control system damping sufficient to guarantee stable contact results in perceptible sluggishness of the control handle's response in free motion. These results suggest that human operator biomechanics must be taken into account to guarantee stable and ergonomic performance of advanced teleoperators.

Anaerobic digestion of alkaline bleaching wastewater from a kraft pulp and paper mill using UASB technique.

PubMed

Larsson, Madeleine; Truong, Xu-Bin; Björn, Annika; Ejlertsson, Jörgen; Bastviken, David; Svensson, Bo H; Karlsson, Anna

2015-01-01

Anaerobic digestion of alkaline kraft elemental chlorine-free bleaching wastewater in two mesophilic, lab-scale upflow anaerobic sludge bed reactors resulted in significantly higher biogas production (250±50 vs. 120±30 NmL g [Formula: see text]) and reduction of filtered total organic carbon (fTOC) (60±5 vs. 43±6%) for wastewater from processing of hardwood (HW) compared with softwood (SW). In all cases, the gas production was likely underestimated due to poor gas separation in the reactors. Despite changes in wastewater characteristics, a stable anaerobic process was maintained with hydraulic retention times (HRTs) between 7 and 14 h. Lowering the HRT (from 13.5 to 8.5 h) did not significantly affect the process, and the stable performance at 8.5 h leaves room for further decreases in HRT. The results show that this type of wastewater is suitable for a full-scale implementation, but the difference in methane potential between SW and HW is important to consider both regarding process dimensioning and biogas yield optimization.

The Dynamical Balance of the Brain at Rest

PubMed Central

Deco, Gustavo; Corbetta, Maurizio

2014-01-01

We review evidence that spontaneous, i.e. not stimulus- or task-driven, activity in the brain is not noise, but orderly organized at the level of large scale systems in a series of functional networks that maintain at all times a high level of coherence. These networks of spontaneous activity correlation or resting state networks (RSN) are closely related to the underlying anatomical connectivity, but their topography is also gated by the history of prior task activation. Network coherence does not depend on covert cognitive activity, but its strength and integrity relates to behavioral performance. Some RSN are functionally organized as dynamically competing systems both at rest and during tasks. Computational studies show that one of such dynamics, the anti-correlation between networks, depends on noise driven transitions between different multi-stable cluster synchronization states. These multi-stable states emerge because of transmission delays between regions that are modeled as coupled oscillators systems. Large-scale systems dynamics are useful for keeping different functional sub-networks in a state of heightened competition, which can be stabilized and fired by even small modulations of either sensory or internal signals. PMID:21196530

Robust dynamic inversion controller design and analysis (using the X-38 vehicle as a case study)

NASA Astrophysics Data System (ADS)

Ito, Daigoro

A new way to approach robust Dynamic Inversion controller synthesis is addressed in this paper. A Linear Quadratic Gaussian outer-loop controller improves the robustness of a Dynamic Inversion inner-loop controller in the presence of uncertainties. Desired dynamics are given by the dynamic compensator, which shapes the loop. The selected dynamics are based on both performance and stability robustness requirements. These requirements are straightforwardly formulated as frequency-dependent singular value bounds during synthesis of the controller. Performance and robustness of the designed controller is tested using a worst case time domain quadratic index, which is a simple but effective way to measure robustness due to parameter variation. Using this approach, a lateral-directional controller for the X-38 vehicle is designed and its robustness to parameter variations and disturbances is analyzed. It is found that if full state measurements are available, the performance of the designed lateral-directional control system, measured by the chosen cost function, improves by approximately a factor of four. Also, it is found that the designed system is stable up to a parametric variation of 1.65 standard deviation with the set of uncertainty considered. The system robustness is determined to be highly sensitive to the dihedral derivative and the roll damping coefficients. The controller analysis is extended to the nonlinear system where both control input displacements and rates are bounded. In this case, the considered nonlinear system is stable up to 48.1° in bank angle and 1.59° in sideslip angle variations, indicating it is more sensitive to variations in sideslip angle than in bank angle. This nonlinear approach is further extended for the actuator failure mode analysis. The results suggest that the designed system maintains a high level of stability in the event of aileron failure. However, only 35% or less of the original stability range is maintained for the rudder failure case. Overall, this combination of controller synthesis and robustness criteria compares well with the mu-synthesis technique. It also is readily accessible to the practicing engineer, in terms of understanding and use.

Effects of ethanol on Pavlovian autoshaping in rats.

PubMed

Tomie, A; Cunha, C; Mosakowski, E M; Quartarolo, N M; Pohorecky, L A; Benjamin, D

1998-09-01

Approach responses, consummatory behaviors, and directed motor responses maintained by food reward resemble autoshaping CRs and are increased by lower doses of ethanol. This study evaluated the effects of presession i.p. injections of ethanol doses (0.00, 0.25, 0.50, 0.70. or 1.00 g/kg) on the acquisition of lever-press autoshaping CR performance in groups of male Long-Evans hooded rats. Paired groups received 15 daily sessions of Pavlovian autoshaping procedures, wherein the insertion of a retractable lever for 5 s (CS) was followed by the response-independent presentation of food (US). Ethanol facilitated lever-press autoshaping CR acquisition, as revealed by dose-related increases in the number of trials on which CRs were performed. The form of the dose-effect curve was inverted U-shaped with maximal responding induced during sessions 1-5 by the 0.70 g/kg ethanol dose. A similar dose-effect curve was observed during sessions 11-15, revealing that the effects of ethanol on autoshaping CR performance were relatively stable. A pseudoconditioning control group injected presession with 0.50 g/kg ethanol received training wherein the food US was presented randomly with respect to the lever CS. Few lever-presses were performed by the Random 0.50 group, indicating that ethanol's effects on autoshaping CR acquisition and maintenance observed in the Paired 0.50 group were not due to its psychomotor activating effects. A non-injection control group performed more autoshaping CRs than did the control group injected presession with saline, indicating that daily presession i.p. injections per se suppress autoshaping CR performance. Results reveal that low doses of ethanol enhance Pavlovian conditioning of directed motor and consummatory-like responding maintained by food reward. Implications for autoshaping accounts of impulsivity and drug abuse are considered.

Continuous cognitive improvement 1 year following successful kidney transplant.

PubMed

Harciarek, Michał; Biedunkiewicz, Bogdan; Lichodziejewska-Niemierko, Monika; Dębska-Ślizień, Alicja; Rutkowski, Bolesław

2011-06-01

Successful kidney transplantation was recently shown to lead to improvement in the cognitive performance of patients on chronic dialysis. To examine whether the early cognitive benefits of transplantation continue to develop over time, along with the patients' ongoing recovery, we addressed these questions in a prospective controlled study of 27 dialyzed patients who subsequently received a kidney transplant, 18 dialyzed patients awaiting kidney transplant, and 30 matched controls without kidney disease. Overall, successful kidney transplant contributed to a statistically significant improvement in performance on tests of motor/psychomotor speed, visual planning, memory, and abstract reasoning tested 1 year later. We also studied whether the cognitive performance of patients maintained on dialysis is stable or declines over time and found that it actually declined over this time even in adequately dialyzed patients. Measures of memory functions were particularly affected. This study indicates that the early beneficial effects of transplantation are not transient and were still evident 1 year following transplantation.

High-Efficiency Plug-and-Play Source of Heralded Single Photons

NASA Astrophysics Data System (ADS)

Montaut, Nicola; Sansoni, Linda; Meyer-Scott, Evan; Ricken, Raimund; Quiring, Viktor; Herrmann, Harald; Silberhorn, Christine

2017-08-01

Reliable generation of single photons is of key importance for fundamental physical experiments and to demonstrate quantum protocols. Waveguide-based photon-pair sources have shown great promise in this regard due to their large spectral tunability, high generation rates, and long temporal coherence of the photon wave packet. However, integrating such sources with fiber-optic networks often results in a strong degradation of performance. We answer this challenge by presenting an alignment-free source of photon pairs in the telecommunications band that maintains heralding efficiency >50 % even after fiber pigtailing, photon separation, and pump suppression. The source combines this outstanding performance in heralding efficiency with a compact, stable, and easy-to-use "plug-and-play" package: one simply connects a laser to the input and detectors to the output, and the source is ready to use. This high performance can be achieved even outside the lab without the need for alignment which makes the source extremely useful for any experiment or demonstration needing heralded single photons.

Program for refan JT8D engine design, fabrication and test, phase 2

NASA Technical Reports Server (NTRS)

Glass, J. A.; Zimmerman, E. S.; Scaramella, V. M.

1975-01-01

The objective of the JT8D refan program was to design, fabricate, and test certifiable modifications of the JT8D engine which would reduce noise generated by JT8D powered aircraft. This was to be accomplished without affecting reliability and maintainability, at minimum retrofit cost, and with no performance penalty. The mechanical design, engine performance and stability characteristics at sea-level and altitude, and the engine noise characteristics of the test engines are documented. Results confirmed the structural integrity of the JT8D-109. Engine operation was stable throughout the airplane flight envelope. Fuel consumption of the test engines was higher than that required to meet the goal of no airplane performance penalty, but the causes were identified and corrected during a normal pre-certification engine development program. Compared to the baseline JT8D-109 engine, the acoustically treated JT8D-109 engine showed noise reductions of 6 PNdB at takeoff and 11 PNdB at a typical approach power setting.

Effects of extended lay-off periods on performance and operator trust under adaptable automation.

PubMed

Chavaillaz, Alain; Wastell, David; Sauer, Jürgen

2016-03-01

Little is known about the long-term effects of system reliability when operators do not use a system during an extended lay-off period. To examine threats to skill maintenance, 28 participants operated twice a simulation of a complex process control system for 2.5 h, with an 8-month retention interval between sessions. Operators were provided with an adaptable support system, which operated at one of the following reliability levels: 60%, 80% or 100%. Results showed that performance, workload, and trust remained stable at the second testing session, but operators lost self-confidence in their system management abilities. Finally, the effects of system reliability observed at the first testing session were largely found again at the second session. The findings overall suggest that adaptable automation may be a promising means to support operators in maintaining their performance at the second testing session. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Graphene-Encapsulated Nanosheet-Assembled Zinc-Nickel-Cobalt Oxide Microspheres for Enhanced Lithium Storage.

PubMed

Zhang, Qiaobao; Chen, Huixin; Han, Xiang; Cai, Junjie; Yang, Yong; Liu, Meilin; Zhang, Kaili

2016-01-01

The appropriate combination of hierarchical transition-metal oxide (TMO) micro-/nanostructures constructed from porous nanobuilding blocks with graphene sheets (GNS) in a core/shell geometry is highly desirable for high-performance lithium-ion batteries (LIBs). A facile and scalable process for the fabrication of 3D hierarchical porous zinc-nickel-cobalt oxide (ZNCO) microspheres constructed from porous ultrathin nanosheets encapsulated by GNS to form a core/shell geometry is reported for improved electrochemical performance of the TMOs as an anode in LIBs. By virtue of their intriguing structural features, the produced ZNCO/GNS core/shell hybrids exhibit an outstanding reversible capacity of 1015 mA h g(-1) at 0.1 C after 50 cycles. Even at a high rate of 1 C, a stable capacity as high as 420 mA h g(-1) could be maintained after 900 cycles, which suggested their great potential as efficient electrodes for high-performance LIBs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Performance of a completely autotrophic nitrogen removal over nitrite process for treating wastewater with different substrates at ambient temperature.

PubMed

Chang, Xiaoyan; Li, Dong; Liang, Yuhai; Yang, Zhuo; Cui, Shaoming; Liu, Tao; Zeng, Huiping; Zhang, Jie

2013-04-01

The stability and parameters of a bio-ceramic filter for completely autotrophic nitrogen removal were investigated. The completely autotrophic nitrogen removal over nitrite (CANON) reactor was fed with different concentrations of ammonia (400, 300, and 200 mg N/L) but constant influent ammonia load. The results showed that the CANON system can achieve good treatment performance at ambient temperature (15-23 degrees C). The average removal rate and removal loading of NH4(+)-N and TN was 83.90%, 1.26 kg N/(m3 x day), and 70.14%, 1.09 kg N/(m3 x day), respectively. Among the influencing factors like pH, dissolved oxygen and alkalinity, it was indicated that the pH was the key parameter of the performance of the CANON system. Observing the variation of pH would contribute to better control of the CANON system in an intuitive and fast way. Denaturing gradient gel electrophoresis analysis of microorganisms further revealed that there were some significant changes in the community structure of ammonium oxidizing bacteria, which had low diversity in different stages, while the species of anaerobic ammonium oxidizing (anammox) bacteria were fewer and the community composition was relatively stable. These observations showed that anaerobic ammonia oxidation was more stable than the aerobic ammonia oxidation, which could explain that why the CANON system maintained a good removal efficiency under the changing substrate conditions.

Multi-cycle operation of enhanced biological phosphorus removal (EBPR) with different carbon sources under high temperature.

PubMed

Shen, Nan; Chen, Yun; Zhou, Yan

2017-05-01

Many studies reported that it is challenging to apply enhanced biological phosphorus removal (EBPR) process at high temperature. Glycogen accumulating organisms (GAOs) could easily gain their dominance over poly-phosphate accumulating organisms (PAOs) when the operating temperature was in the range of 25 °C-30 °C. However, a few successful EBPR processes operated at high temperature have been reported recently. This study aimed to have an in-depth understanding on the impact of feeding strategy and carbon source types on EBPR performance in tropical climate. P-removal performance of two EBPR systems was monitored through tracking effluent quality and cyclic studies. The results confirmed that EBPR was successfully obtained and maintained at high temperature with a multi-cycle strategy. More stable performance was observed with acetate as the sole carbon source compared to propionate. Stoichiometric ratios of phosphorus and carbon transformation during both anaerobic and aerobic phases were higher at high temperature than low temperature (20±1 °C) except anaerobic PHA/C ratios within most of the sub-cycles. Furthermore, the fractions of PHA and glycogen in biomass were lower compared with one-cycle pulse feed operation. The microbial community structure was more stable in acetate-fed sequencing batch reactor (C2-SBR) than that in propionate-fed reactor (C3-SBR). Accumulibacter Clade IIC was found to be highly abundant in both reactors. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dyachenko, Sergey A.; Zlotnik, Anatoly; Korotkevich, Alexander O.

Here, we develop an operator splitting method to simulate flows of isothermal compressible natural gas over transmission pipelines. The method solves a system of nonlinear hyperbolic partial differential equations (PDEs) of hydrodynamic type for mass flow and pressure on a metric graph, where turbulent losses of momentum are modeled by phenomenological Darcy-Weisbach friction. Mass flow balance is maintained through the boundary conditions at the network nodes, where natural gas is injected or withdrawn from the system. Gas flow through the network is controlled by compressors boosting pressure at the inlet of the adjoint pipe. Our operator splitting numerical scheme ismore » unconditionally stable and it is second order accurate in space and time. The scheme is explicit, and it is formulated to work with general networks with loops. We test the scheme over range of regimes and network configurations, also comparing its performance with performance of two other state of the art implicit schemes.« less

Hierarchical porous poly (ether sulfone) membranes with excellent capacity retention for vanadium flow battery application

NASA Astrophysics Data System (ADS)

Chen, Dongju; Li, Dandan; Li, Xianfeng

2017-06-01

A hierarchical poly (ether sulfone) (PES) porous membrane is facilely fabricated via a hard template method for vanadium flow battery (VFB) application. The construction of this hierarchical porous membrane is prepared via removing templates (phenolphthalein). The pore size can be well controlled by optimizing the template content in the cast solution, ensuring the membrane conductivity and selectively. The prepared hierarchical porous membrane can combine high ion selectivity with high proton conductivity, which renders a good electrochemical performance in a VFB. The optimized hierarchical porous membrane shows a columbic efficiency of 94.52% and energy efficiency of 81.66% along with a superior ability to maintain stable capacity over extended cycling at a current density of 80 mA cm-2. The characteristics of low cost, proven chemical stability and high electrochemical performance afford the hierarchical PES porous membrane great prospect in VFB application.

Production and characterization of pure cryogenic inertial fusion targets

NASA Astrophysics Data System (ADS)

Boyd, B. A.; Kamerman, G. W.

An experimental cryogenic inertial fusion target generator and two optical techniques for automated target inspection are described. The generator produces 100 microns diameter solid hydrogen spheres at a rate compatible with fueling requirements of conceptual inertial fusion power plants. A jet of liquified hydrogen is disrupted into droplets by an ultrasonically excited nozzle. The droplets solidify into microspheres while falling through a chamber maintained below the hydrogen triple point pressure. Stable operation of the generator has been demonstrated for up to three hours. The optical inspection techniques are computer aided photomicrography and coarse diffraction pattern analysis (CDPA). The photomicrography system uses a conventional microscope coupled to a computer by a solid state camera and digital image memory. The computer enhances the stored image and performs feature extraction to determine pellet parameters. The CDPA technique uses Fourier transform optics and a special detector array to perform optical processing of a target image.

Genome accessibility is widely preserved and locally modulated during mitosis

PubMed Central

Hsiung, Chris C.-S.; Morrissey, Christapher S.; Udugama, Maheshi; Frank, Christopher L.; Keller, Cheryl A.; Baek, Songjoon; Giardine, Belinda; Crawford, Gregory E.; Sung, Myong-Hee; Hardison, Ross C.

2015-01-01

Mitosis entails global alterations to chromosome structure and nuclear architecture, concomitant with transient silencing of transcription. How cells transmit transcriptional states through mitosis remains incompletely understood. While many nuclear factors dissociate from mitotic chromosomes, the observation that certain nuclear factors and chromatin features remain associated with individual loci during mitosis originated the hypothesis that such mitotically retained molecular signatures could provide transcriptional memory through mitosis. To understand the role of chromatin structure in mitotic memory, we performed the first genome-wide comparison of DNase I sensitivity of chromatin in mitosis and interphase, using a murine erythroblast model. Despite chromosome condensation during mitosis visible by microscopy, the landscape of chromatin accessibility at the macromolecular level is largely unaltered. However, mitotic chromatin accessibility is locally dynamic, with individual loci maintaining none, some, or all of their interphase accessibility. Mitotic reduction in accessibility occurs primarily within narrow, highly DNase hypersensitive sites that frequently coincide with transcription factor binding sites, whereas broader domains of moderate accessibility tend to be more stable. In mitosis, proximal promoters generally maintain their accessibility more strongly, whereas distal regulatory elements tend to lose accessibility. Large domains of DNA hypomethylation mark a subset of promoters that retain accessibility during mitosis and across many cell types in interphase. Erythroid transcription factor GATA1 exerts site-specific changes in interphase accessibility that are most pronounced at distal regulatory elements, but has little influence on mitotic accessibility. We conclude that features of open chromatin are remarkably stable through mitosis, but are modulated at the level of individual genes and regulatory elements. PMID:25373146

Characterization and differentiation of human embryonic stem cells.

PubMed

Carpenter, M K; Rosler, E; Rao, M S

2003-01-01

Cell replacement therapies have been limited by the availability of sufficient quantities of cells for transplantation. Human ES (hES) cell lines have recently been generated by several laboratories. When maintained for over 1 year in vitro, they remain karyotypically and phenotypically stable and may therefore provide an excellent source material for cell therapies. Currently, data is available for 26 hES cell lines. Although limited characterization has been performed on most of these lines, there are remarkable similarities in expression of markers. hES cell lines derived in different laboratories show similar expression profiles of surface markers, including SSEA-4, Tra-1-60, and Tra-1-81. In addition, markers associated with pluripotent cells such as OCT-4 are expressed at in all cell lines tested. These cells express high levels of telomerase and appear to have indefinite growth potential. The generation of the large quantities of cells necessary for cell replacement therapies will require a cell population which is stable over long term culture. We have characterized the properties of multiple hES cell lines that have been maintained in culture for extended periods. Quantitative analyses demonstrate that all of the cell lines examined show consistent marker expression and retain a normal karyotype after long-term culture. hES cells have been differentiated into the derivatives of all three germ layers. Specifically this includes cardiomyocytes, neural cells, hepatocyte-like cells, endothelial cells and hematopoietic progenitor cells. These data demonstrating the karyotypic and phenotypic stability of hES cells and their extensive differentiative capacity indicate that they may be an appropriate source of cells for multiple regenerative medicine applications.

Use of motor abundance in old adults in the regulation of a narrow-based stance.

PubMed

Hsu, Wei-Li; Lin, Kwan-Hwa; Yang, Rong-Sen; Cheng, Chih-Hsiu

2014-02-01

The ability to maintain stable balance while standing decreases with age. The body must coordinate multiple joints using "freeze" or "free" strategy, or a combination of both to ensure balance stability. The purpose of this study was to examine age-related changes in the use of motor abundance during upright stance on a narrow base without visual input. Uncontrolled manifold (UCM) analysis was used to decompose the movement variability of joints into goal-equivalent variability (GEV) and non-goal-equivalent variability (NGEV). The ratio between GEV and NGEV (UCM(ratio)) quantifies the joint coordination related to postural stability, and a high UCM(ratio) value indicates flexible control of joints. To perform balance tests, participants in this study (healthy young and old adults, 20 each) were asked to stand on a flat platform and on narrow wooden blocks with their eyes open and then eyes closed. In upright balance tests, both old and young adults maintained postural stability. GEV was greater than NGEV across all participants and conditions. However, GEV was higher in the young adults than in the old adults, whereas NGEV was higher in the old adults than in the young adults. Therefore, the old adults exhibited a lower UCM(ratio) than the young adults. The old adults were unable to exploit motor abundance and used a less flexible multi-joint coordination pattern to achieve stable balance. The UCM(ratio) value reflects the quality of postural control and can be used for assessing joint coordination in balance disorders.

Fabrication of transparent conductive tri-composite film for electrochromic application

NASA Astrophysics Data System (ADS)

Choi, Dahyun; Lee, Minji; Kim, Hyungsub; Chu, Won-shik; Chun, Doo-man; Ahn, Sung-Hoon; Lee, Caroline Sunyong

2017-12-01

A transparent conductive electrode (TCE) based on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) was developed using a dry deposition method for application as an electrochromic (EC) device. To improve its electrical conductivity and stable EC performance, AgNW and TiO2 nanoparticles were included in the TCE film. The resulting TiO2/AgNW/PEDOT:PSS hybrid film showed electrical sheet resistivity of 23 Ω/sq., similar to that of a commercial TCE film. When +2.0 V was applied to the hybrid film, the response current was stable, maintaining a value of 2.0 mA. We found that the hybrid film could be used as an EC device, without using commercial TCE film. Antimony-doped tin oxide on indium-doped tin oxide-glass as an ion-storage layer was combined with the hybrid film, with 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM-TFSI) injected into the EC device as an ionic liquid electrolyte. The optical transmittance difference between the colored and bleached states was 23% at 630 nm; under applied voltages of -2.0 V and +2.0 V, the coloration efficiency was 127.83 cm2/C. Moreover, cyclic transmittance with switching voltage for 3 h showed stable optical transmittance of 31% at 630 nm. Cyclic voltammetry measurements indicated stable behavior over 50 cycles. Thus, the proposed TCE configuration (TiO2/AgNW/PEDOT:PSS) shows great potential as a substitute for commercial TCEs, the cost of which depends on the availability of rare-earth materials.

Stabilized Lanthanum Sulphur Compounds

NASA Technical Reports Server (NTRS)

Reynolds, George H. (Inventor); Elsner, Norbert B. (Inventor); Shearer, Clyde H. (Inventor)

1985-01-01

Lanthanum sulfide is maintained in the stable cubic phase form over a temperature range of from 500 C to 1500 C by adding to it small amounts of calcium, barium. or strontium. This novel compound is an excellent thermoelectric material.

Polymorphism in the two-locus Levene model with nonepistatic directional selection.

PubMed

Bürger, Reinhard

2009-11-01

For the Levene model with soft selection in two demes, the maintenance of polymorphism at two diallelic loci is studied. Selection is nonepistatic and dominance is intermediate. Thus, there is directional selection in every deme and at every locus. We assume that selection is in opposite directions in the two demes because otherwise no polymorphism is possible. If at one locus there is no dominance, then a complete analysis of the dynamical and equilibrium properties is performed. In particular, a simple necessary and sufficient condition for the existence of an internal equilibrium and sufficient conditions for global asymptotic stability are obtained. These results are extended to deme-independent degree of dominance at one locus. A perturbation analysis establishes structural stability within the full parameter space. In the absence of genotype-environment interaction, which requires deme-independent dominance at both loci, nongeneric equilibrium behavior occurs, and the introduction of arbitrarily small genotype-environment interaction changes the equilibrium structure and may destroy stable polymorphism. The volume of the parameter space for which a (stable) two-locus polymorphism is maintained is computed numerically. It is investigated how this volume depends on the strength of selection and on the dominance relations. If the favorable allele is (partially) dominant in its deme, more than 20% of all parameter combinations lead to a globally asymptotically stable, fully polymorphic equilibrium.

Long-term anaerobic digestion of food waste stabilized by trace elements

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang Lei, E-mail: wxzyfx@yahoo.com; Jahng, Deokjin, E-mail: djahng@mju.ac.kr

Highlights: Black-Right-Pointing-Pointer Korean food waste was found to contain low level of trace elements. Black-Right-Pointing-Pointer Stable anaerobic digestion of food waste was achieved by adding trace elements. Black-Right-Pointing-Pointer Iron played an important role in anaerobic digestion of food waste. Black-Right-Pointing-Pointer Cobalt addition further enhanced the process performance in the presence of iron. - Abstract: The purpose of this study was to examine if long-term anaerobic digestion of food waste in a semi-continuous single-stage reactor could be stabilized by supplementing trace elements. Contrary to the failure of anaerobic digestion of food waste alone, stable anaerobic digestion of food waste was achievedmore » for 368 days by supplementing trace elements. Under the conditions of OLR (organic loading rates) of 2.19-6.64 g VS (volatile solid)/L day and 20-30 days of HRT (hydraulic retention time), a high methane yield (352-450 mL CH{sub 4}/g VS{sub added}) was obtained, and no significant accumulation of volatile fatty acids was observed. The subsequent investigation on effects of individual trace elements (Co, Fe, Mo and Ni) showed that iron was essential for maintaining stable methane production. These results proved that the food waste used in this study was deficient in trace elements.« less

An electromyographic analysis of shoulder muscle activation during push-up variations on stable and labile surfaces.

PubMed

Sandhu, Jaspal S; Mahajan, Shruti; Shenoy, Shweta

2008-04-01

Numerous exercises are used to strengthen muscles around the shoulder joint including the push-up and the push-up plus. An important consideration is the addition of surface instability in the form of swiss ball for rehabilitation and strength. The justification for the use of the swiss ball is based on its potential for increasing muscular demand required to maintain postural stability and for improving joint proprioception. Evidence for this is lacking in literature. To compare the myoelectric amplitude of shoulder muscles during push-ups on labile and stable surface. Same subject experimental study. Thirty healthy male subjects in the age group 20-30 years with a mean height of 173.65 cm (+/- SD 2.56) and a mean weight of 69.9 kg (+/-SD 0.2) were taken. Surface electromyogram was recorded from triceps, pectoralis major, serratus anterior and upper trapezius while performing push-up and push-up plus exercises, both on labile and stable surface. Significant increase in muscle activity was observed in pectoralis major and triceps muscle (only during eccentric phase of elbow pushups), while serratus anterior and upper trapezius showed no change in activation level on swiss ball. The addition of a swiss ball is capable of influencing shoulder muscle activity during push-up variations, although the effect is task and muscle dependent.

Diversity, Productivity, and Stability of an Industrial Microbial Ecosystem

PubMed Central

Tang, Pei-Zhong; Becker, Scott; Hoang, Tony; Bilgin, Damla; Lim, Yan Wei; Peterson, Todd C.; Mayfield, Stephen; Haerizadeh, Farzad; Shurin, Jonathan B.; Bafna, Vineet; McBride, Robert

2016-01-01

Managing ecosystems to maintain biodiversity may be one approach to ensuring their dynamic stability, productivity, and delivery of vital services. The applicability of this approach to industrial ecosystems that harness the metabolic activities of microbes has been proposed but has never been tested at relevant scales. We used a tag-sequencing approach with bacterial small subunit rRNA (16S) genes and eukaryotic internal transcribed spacer 2 (ITS2) to measuring the taxonomic composition and diversity of bacteria and eukaryotes in an open pond managed for bioenergy production by microalgae over a year. Periods of high eukaryotic diversity were associated with high and more-stable biomass productivity. In addition, bacterial diversity and eukaryotic diversity were inversely correlated over time, possibly due to their opposite responses to temperature. The results indicate that maintaining diverse communities may be essential to engineering stable and productive bioenergy ecosystems using microorganisms. PMID:26896141

A hierarchy of strategies heroin-using mothers employ to reduce harm to their children.

PubMed

Richter, K P; Bammer, G

2000-12-01

The present paper explores strategies that drug-using women employ to protect their children from drug-related harm. Twenty-two mothers were recruited through word-of-mouth, field recruitment, and flyers. Semi-structured interviews were used to collect mother's views on parenting and heroin use. Analysis was conducted using a standard qualitative software package. A hierarchy of seven strategies was identified: (1) stop using; (2) go into treatment; (3) maintain a stable small habit; (4) shield children from drug-related activities; (5) keep the home environment stable, safe, and secure; (6) stay out of gaol; and, if the children's needs still cannot be met, (7) place them with a trusted caregiver and maintain as active a parental role as possible. These strategies, derived innovatively from mothers' experiences, provide progressive goals for treatment and can also serve as measures of success. In addition, they may determine how well children fare in drug-affected families.

Electrically Conductive and Protective Coating for Planar SOFC Stacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Jung-Pyung; Stevenson, Jeffry W.

Ferritic stainless steels are preferred interconnect materials for intermediate temperature SOFCs because of their resistance to oxidation, high formability and low cost. However, their protective oxide layer produces Cr-containing volatile species at SOFC operating temperatures and conditions, which can cause cathode poisoning. Electrically conducting spinel coatings have been developed to prevent cathode poisoning and to maintain an electrically conductive pathway through SOFC stacks. However, this coating is not compatible with the formation of stable, hermetic seals between the interconnect frame component and the ceramic cell. Thus, a new aluminizing process has been developed by PNNL to enable durable sealing, preventmore » Cr evaporation, and maintain electrical insulation between stack repeat units. Hence, two different types of coating need to have stable operation of SOFC stacks. This paper will focus on the electrically conductive coating process. Moreover, an advanced coating process, compatible with a non-electrically conductive coating will be« less

Diversity, Productivity, and Stability of an Industrial Microbial Ecosystem.

PubMed

Beyter, Doruk; Tang, Pei-Zhong; Becker, Scott; Hoang, Tony; Bilgin, Damla; Lim, Yan Wei; Peterson, Todd C; Mayfield, Stephen; Haerizadeh, Farzad; Shurin, Jonathan B; Bafna, Vineet; McBride, Robert

2016-04-01

Managing ecosystems to maintain biodiversity may be one approach to ensuring their dynamic stability, productivity, and delivery of vital services. The applicability of this approach to industrial ecosystems that harness the metabolic activities of microbes has been proposed but has never been tested at relevant scales. We used a tag-sequencing approach with bacterial small subunit rRNA (16S) genes and eukaryotic internal transcribed spacer 2 (ITS2) to measuring the taxonomic composition and diversity of bacteria and eukaryotes in an open pond managed for bioenergy production by microalgae over a year. Periods of high eukaryotic diversity were associated with high and more-stable biomass productivity. In addition, bacterial diversity and eukaryotic diversity were inversely correlated over time, possibly due to their opposite responses to temperature. The results indicate that maintaining diverse communities may be essential to engineering stable and productive bioenergy ecosystems using microorganisms. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Environmental Perturbations, Behavioral Change, and Population Response in a Long-Term Northern Elephant Seal Study

DTIC Science & Technology

2014-09-30

maintain either constant immigration or reproductive rates near 1.0 to maintain stable population growth. IMPACT/APPLICATIONS Using...Costa. 2013. Movement and diving patterns of juvenile male South American sea lions off the coast of central Chile . Marine Mammal Science:n/a-n/a...coast of central Chile . Marine Mammal Science 30:1175-1183. Jeglinski, J. W., K. T. Goetz, C. Werner, D. P. Costa, and F. Trillmich. 2013. Same

Behaviour of molecular weight distribution for the liquid fraction of pig slurry treated by anaerobic digestion.

PubMed

Rodríguez, D C; Belmonte, M; Peñuela, G; Campos, J L; Vidal, G

2011-01-01

Pig slurry was treated in an upflow anaerobic sludge blanket (UASB) reactor. To maintain a stable operation, the organic loading rate (OLR) applied to the system was increased stepwise by decreasing the dilution ratio of the pig slurry. Finally, during the last operational stage, no dilution was applied to the influent. The reactor maintained a soluble chemical oxygen demand (CODs) removal efficiency of 82% when OLRs lower than 1.73 g CODs l(-1) d(-1) were applied, although its efficiency fell to 55% when operated at 2.48 g CODs l(-1) d(-1). System performance was not affected by the presence of free ammonia (concentrations up to 375 mg NH3 l(-1)). The distribution of the different molecular weight fractions changed significantly during anaerobic digestion. Proteins contained in the fractions higher than 10,000 Daltons are less degraded than those belonging to the lower fractions. An important percentage of both COD and BOD5 in the effluent were observed in the lowest fraction, probably caused by the presence of volatile fatty acids (VFA).

Stability and the Evolvability of Function in a Model Protein

PubMed Central

Bloom, Jesse D.; Wilke, Claus O.; Arnold, Frances H.; Adami, Christoph

2004-01-01

Functional proteins must fold with some minimal stability to a structure that can perform a biochemical task. Here we use a simple model to investigate the relationship between the stability requirement and the capacity of a protein to evolve the function of binding to a ligand. Although our model contains no built-in tradeoff between stability and function, proteins evolved function more efficiently when the stability requirement was relaxed. Proteins with both high stability and high function evolved more efficiently when the stability requirement was gradually increased than when there was constant selection for high stability. These results show that in our model, the evolution of function is enhanced by allowing proteins to explore sequences corresponding to marginally stable structures, and that it is easier to improve stability while maintaining high function than to improve function while maintaining high stability. Our model also demonstrates that even in the absence of a fundamental biophysical tradeoff between stability and function, the speed with which function can evolve is limited by the stability requirement imposed on the protein. PMID:15111394

Ferroelectric nanostructure having switchable multi-stable vortex states

DOEpatents

Naumov, Ivan I [Fayetteville, AR; Bellaiche, Laurent M [Fayetteville, AR; Prosandeev, Sergey A [Fayetteville, AR; Ponomareva, Inna V [Fayetteville, AR; Kornev, Igor A [Fayetteville, AR

2009-09-22

A ferroelectric nanostructure formed as a low dimensional nano-scale ferroelectric material having at least one vortex ring of polarization generating an ordered toroid moment switchable between multi-stable states. A stress-free ferroelectric nanodot under open-circuit-like electrical boundary conditions maintains such a vortex structure for their local dipoles when subject to a transverse inhomogeneous static electric field controlling the direction of the macroscopic toroidal moment. Stress is also capable of controlling the vortex's chirality, because of the electromechanical coupling that exists in ferroelectric nanodots.

A low power cryocooled autonomous ultra-stable oscillator

NASA Astrophysics Data System (ADS)

Fluhr, C.; Dubois, B.; Grop, S.; Paris, J.; Le Tetû, G.; Giordano, V.

2016-12-01

We present the design and the preliminary evaluation of a cryostat equipped with a low power pulse-tube cryocooler intended to maintain near 5 K a high-Q factor sapphire microwave resonator. This cooled resonator constitutes the frequency reference of an ultra-stable oscillator presenting a short term fractional frequency stability of better than 1 ×10-15 . The proposed design enables to reach a state-of-the-art frequency stability with a cryogenic oscillator consuming only 3 kW of electrical power.

Evaluation of behaviour in stabled draught horse foals fed diets with two protein levels.

PubMed

Sartori, C; Guzzo, N; Normando, S; Bailoni, L; Mantovani, R

2017-01-01

The present work is aimed at evaluating the behaviour of Italian Heavy Draught Horse (IHDH) foals reared in semi-covered stables and fed two isoenergetic total mixed rations with different dietary protein levels (13.2% and 10.6% of CP on dry matter). The study was prompted by the restrictions for nitrate emissions in farms of the European Nitrate Directive. One suggested solution is to reduce dietary protein while maintaining normal performance and welfare, but there is a lack of literature in studies of horses. The behaviours of 20 foals of 437±60 kg of BW, aged 379±37 days and stabled in four pens by sex (S) and diet (D) were video recorded and analysed to build a suitable ethogram including 18 behaviours in six categories: ingestion, resting, maintenance, movement, social activities, other. The percentage of the daily time spent in each behavioural category and single behaviours was analysed via a single traits GLM including S, D and their interaction. Daily activity was consistent with existing literature: foals spent about 33% of the day in ingestion activities and 41% in resting, whereas social interactions constituted 8% of the time and individual maintenance <2%. Concerning diet, foals fed high protein spent more time in movement (19.62±0.73% of day v. 10.45±0.73% in low-protein (LP) foals; P⩽0.001), whereas the LP group increased resting (43.42±1.12% v. 38.02±1.12%; P⩽0.001). No stereotypies were found, and daily activity followed the typical values for draught breeds for foals in both dietary groups, a result that suggests the maintenance of well-being after dietary protein reduction. This result, together with the findings of a companion study showing no changes in growth performances of foals, showed that a reduction of CP in foal diet is reconcilable with the maintenance of performance and welfare.

Testbed-based Performance Evaluation of Attack Resilient Control for AGC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ashok, Aditya; Sridhar, Siddharth; McKinnon, Archibald D.

The modern electric power grid is a complex cyber-physical system whose reliable operation is enabled by a wide-area monitoring and control infrastructure. This infrastructure, supported by an extensive communication backbone, enables several control applications functioning at multiple time scales to ensure the grid is maintained within stable operating limits. Recent events have shown that vulnerabilities in this infrastructure may be exploited to manipulate the data being exchanged. Such a scenario could cause the associated control application to mis-operate, potentially causing system-wide instabilities. There is a growing emphasis on looking beyond traditional cybersecurity solutions to mitigate such threats. In this papermore » we perform a testbed-based validation of one such solution - Attack Resilient Control (ARC) - on Iowa State University's \\textit{PowerCyber} testbed. ARC is a cyber-physical security solution that combines domain-specific anomaly detection and model-based mitigation to detect stealthy attacks on Automatic Generation Control (AGC). In this paper, we first describe the implementation architecture of the experiment on the testbed. Next, we demonstrate the capability of stealthy attack templates to cause forced under-frequency load shedding in a 3-area test system. We then validate the performance of ARC by measuring its ability to detect and mitigate these attacks. Our results reveal that ARC is efficient in detecting stealthy attacks and enables AGC to maintain system operating frequency close to its nominal value during an attack. Our studies also highlight the importance of testbed-based experimentation for evaluating the performance of cyber-physical security and control applications.« less

Functional integration and self-template synthesis of hollow core-shell carbon mesoporous spheres/Fe3O4/nitrogen-doped graphene to enhance catalytic activity in DSSCs.

PubMed

Yao, Jixin; Zhang, Kang; Wang, Wen; Zuo, Xueqin; Yang, Qun; Tang, Huaibao; Wu, Mingzai; Li, Guang

2018-05-03

Excellent corrosion resistance is crucial for photovoltaic devices to acquire high and stable performance under high corrosive complicated environments. Creative inspiration comes from sandwich construction, whereby Fe3O4 nanoparticles were anchored onto hollow core-shell carbon mesoporous microspheres and wrapped by N-graphene nanosheets (HCCMS/Fe3O4@N-RGO) to obtain integrated high corrosive resistance and stability. The as-prepared multiple composite material possesses outstanding performance as a result of structure optimization, performance improvement, and interface synergy. Therefore, it can effectively suppress corrosion from the electrolyte in recycled tests many times, indicating the ultrahigh corrosion resistance life of this double carbon-based nanocomposite. Furthermore, the electrical conductivity and conversion efficiency of the composite are well maintained due to the triple synergistic interactions, which could serve as a guideline in establishing high-performance multifunctional HCCMS/Fe3O4@N-RGO with great prospects in energy devices, such as lithium batteries, supercapacitors and electrode materials, etc.

Application of quadratic optimization to supersonic inlet control

NASA Technical Reports Server (NTRS)

Lehtinen, B.; Zeller, J. R.

1971-01-01

The application of linear stochastic optimal control theory to the design of the control system for the air intake (inlet) of a supersonic air-breathing propulsion system is discussed. The controls must maintain a stable inlet shock position in the presence of random airflow disturbances and prevent inlet unstart. Two different linear time invariant control systems are developed. One is designed to minimize a nonquadratic index, the expected frequency of inlet unstart, and the other is designed to minimize the mean square value of inlet shock motion. The quadratic equivalence principle is used to obtain the best linear controller that minimizes the nonquadratic performance index. The two systems are compared on the basis of unstart prevention, control effort requirements, and sensitivity to parameter variations.

Cubic KTi2(PO4)3 as electrode materials for sodium-ion batteries.

PubMed

Han, Jin; Xu, Maowen; Niu, Yubin; Jia, Min; Liu, Ting; Li, Chang Ming

2016-12-01

A novel cubic KTi2(PO4)3 is successfully synthesized via a facile hydrothermal method combined with a subsequent annealing treatment and further used as electrode material for sodium-ion batteries for the first time. For comparison, carbon-coated KTi2(PO4)3 obtained by a normal cane sugar-assisted method reveals superior electrochemical performances in sodium-ion battery. Besides of the high coulombic efficiency of nearly 100% after 100 cycles, a stable capacity of 112mAhg(-1) can be achieved at 0.5C after 100 cycles, and still maintains to 105mAhg(-1) after 500 cycles with capacity retention of approximately 90%. Copyright © 2016 Elsevier Inc. All rights reserved.

Ilizarov ring fixator for a difficult case of ankle syndesmosis disruption.

PubMed

Relwani, Jaikumar; Lahoti, Om; Orakwe, Sam

2002-01-01

Syndesmotic stabilization is recommended for tibiofibular diastasis, a Maisonneuve fracture, or syndesmotic instability after fixation of distal tibia-fibula fractures. In the case presented, a syndesmotic stabilization was performed with a screw inserted 2 cm above the tibiotalar joint Subsequent failure occurred due to the weight of the patient and a lack of compliance with the necessary nonweight bearing protocol. The Ilizarov frame was used to reduce and maintain a stable syndesmosis with a simple two-ring construct which allowed the patient to bear weight on the injured limb while his syndesmosis healed. This is not recommend as a routine method of treatment, but is presented as an extended indication of the Ilizarov frame for difficult cases.

Compactly packaged monolithic four-wavelength VCSEL array with 100-GHz wavelength spacing for future-proof mobile fronthaul transport.

PubMed

Lee, Eun-Gu; Mun, Sil-Gu; Lee, Sang Soo; Lee, Jyung Chan; Lee, Jong Hyun

2015-01-12

We report a cost-effective transmitter optical sub-assembly using a monolithic four-wavelength vertical-cavity surface-emitting laser (VCSEL) array with 100-GHz wavelength spacing for future-proof mobile fronthaul transport using the data rate of common public radio interface option 6. The wavelength spacing is achieved using selectively etched cavity control layers and fine current adjustment. The differences in operating current and output power for maintaining the wavelength spacing of four VCSELs are <1.4 mA and <1 dB, respectively. Stable operation performance without mode hopping is observed, and error-free transmission under direct modulation is demonstrated over a 20-km single-mode fiber without any dispersion-compensation techniques.

Hydrologic modeling strategy for the Islamic Republic of Mauritania, Africa

USGS Publications Warehouse

Friedel, Michael J.

2008-01-01

The government of Mauritania is interested in how to maintain hydrologic balance to ensure a long-term stable water supply for minerals-related, domestic, and other purposes. Because of the many complicating and competing natural and anthropogenic factors, hydrologists will perform quantitative analysis with specific objectives and relevant computer models in mind. Whereas various computer models are available for studying water-resource priorities, the success of these models to provide reliable predictions largely depends on adequacy of the model-calibration process. Predictive analysis helps us evaluate the accuracy and uncertainty associated with simulated dependent variables of our calibrated model. In this report, the hydrologic modeling process is reviewed and a strategy summarized for future Mauritanian hydrologic modeling studies.

Dynamic electrical characteristics of low-power ring oscillators constructed with inorganic nanoparticles on flexible plastics.

PubMed

Yun, Junggwon; Cho, Kyoungah; Kim, Sangsig

2012-11-01

In this study, we demonstrate for the first time the low-power and stable performance of a ring oscillator constructed on a flexible plastic with solution-processable inorganic nanoparticles (NPs). Our flexible ring oscillator is composed of three inverters based on n- and p-type inorganic NP thin-film transistors. Each of the component inverters exhibits a gain of ∼80 at a voltage of 5 V. For the ring oscillator, the sine waves are generated with a frequency of up to 12 kHz. The waveforms are undistorted under strained conditions and maintained even after 5000 bending cycles. The frequency and waveform of the output waves obtained from our flexible ring oscillator are analyzed and discussed in detail.

Kleptothermy: an additional category of thermoregulation, and a possible example in sea kraits (Laticauda laticaudata, Serpentes).

PubMed

Brischoux, François; Bonnet, Xavier; Shine, Richard

2009-12-23

Lacking the capacity for thermogenesis, most ectotherms inhabiting thermally heterogeneous environments rely instead upon exploiting that ambient heterogeneity. In many cases they maintain body temperatures within a narrow range despite massive spatial and temporal variation in ambient conditions. Reliance on diverse thermal opportunities is reflected in specific terms for organisms that bask in sunlight to regulate their temperature (heliotherms), or that press their bodies against warm substrates to facilitate heat flow (thigmotherms), or that rely on large body mass to maintain thermal constancy (gigantothermy). We propose an additional category of thermoregulators: kleptotherms, which regulate their own temperature by 'stealing' heat from other organisms. This concept involves two major conditions: the thermal heterogeneity created by the presence of a warm organism in a cool environment and the selective use of that heterogeneity by another animal to maintain body temperatures at higher (and more stable) levels than would be possible elsewhere in the local area. Kleptothermy occurs in endotherms also, but is usually reciprocal (rather than unilateral as in ectotherms). Thermal monitoring on a small tropical island documents a possible example of kleptothermy, based on high stable temperatures of a sea snake (Laticauda laticaudata) inside a burrow occupied by seabirds.

C.E.R.A. administered once monthly corrects and maintains stable hemoglobin levels in chronic kidney disease patients not on dialysis: the observational study MICENAS II.

PubMed

Martínez-Castelao, Alberto; Cases, Aleix; Coll, Elisabeth; Bonal, Jordi; Galceran, Josep M; Fort, Joan; Moreso, Francesc; Torregrosa, Vicente; Guirado, Lluís; Ruiz, Pilar

2015-01-01

C.E.R.A. (continuous erythropoietin receptor activator, pegilated-rHuEPO ß) corrects and maintains stable hemoglobin levels in once-monthly administration in chronic kidney disease (CKD) patients. The aim of this study was to evaluate the management of anemia with C.E.R.A. in CKD patients not on dialysis in the clinical setting. Two hundred seventy two anemic CKD patients not on dialysis treated with C.E.R.A. were included in this retrospective, observational, multicentric study during 2010. Demographical characteristics, analytical parameters concerning anemia, treatment data and iron status were recorded. C.E.R.A. achieved a good control of anemia in both naïve patients (mean Hemoglobin 11.6g/dL) and patients converted from a previous ESA (mean Hemoglobin 11.7g/dL). Most naïve patients received C.E.R.A. once monthly during the correction phase and required a low monthly dose (median dose 75 µg/month). The same median dose was required in patients converted from a previous ESA, and it was lower than recommended in the Summary of Product Characteristics (SPC). Iron status was adequate in 75% of anemic CKD patients, but only 50% of anemic patients with iron deficiency received iron supplementation. C.E.R.A. corrects and maintains stable hemoglobin levels in anemic CKD patients not on dialysis, requiring conversion doses lower than those recommended by the SPC, and achieving target hemoglobin levels with once-monthly dosing frequency both in naïve and converted patients.

Histological findings in two renal transplants accomplishing operational tolerance criteria

PubMed Central

Azancot, M.A.; Cantarell, C.; Torres, I.B.; Serón, D.R.

2011-01-01

Operational tolerance is defined as stable renal function in transplants without immunosuppression for at least 1 year. We present histological assessments of two patients with operational tolerance. The first withdrew immunosuppression in 2005 and presents stable renal function (creatinine 1.5 mg/dL) without proteinuria. The biopsy showed mild chronic tubulointerstitial changes without inflammation. The second withdrew immunosuppression in 2009 and maintains stable renal function (creatinine 1.6 mg/dL) with mild proteinuria. Histology showed chronic humoural rejection and Class II anti-human leukocyte antigen antibodies were detected. These cases suggest that a renal biopsy may be useful to rule out subclinical pathology in patients with operational tolerance. PMID:25984157

Histological findings in two renal transplants accomplishing operational tolerance criteria.

PubMed

Azancot, M A; Moreso, F; Cantarell, C; Torres, I B; Serón, D R

2011-06-01

Operational tolerance is defined as stable renal function in transplants without immunosuppression for at least 1 year. We present histological assessments of two patients with operational tolerance. The first withdrew immunosuppression in 2005 and presents stable renal function (creatinine 1.5 mg/dL) without proteinuria. The biopsy showed mild chronic tubulointerstitial changes without inflammation. The second withdrew immunosuppression in 2009 and maintains stable renal function (creatinine 1.6 mg/dL) with mild proteinuria. Histology showed chronic humoural rejection and Class II anti-human leukocyte antigen antibodies were detected. These cases suggest that a renal biopsy may be useful to rule out subclinical pathology in patients with operational tolerance.

Improvement of sidestream dark field imaging with an image acquisition stabilizer.

PubMed

Balestra, Gianmarco M; Bezemer, Rick; Boerma, E Christiaan; Yong, Ze-Yie; Sjauw, Krishan D; Engstrom, Annemarie E; Koopmans, Matty; Ince, Can

2010-07-13

In the present study we developed, evaluated in volunteers, and clinically validated an image acquisition stabilizer (IAS) for Sidestream Dark Field (SDF) imaging. The IAS is a stainless steel sterilizable ring which fits around the SDF probe tip. The IAS creates adhesion to the imaged tissue by application of negative pressure. The effects of the IAS on the sublingual microcirculatory flow velocities, the force required to induce pressure artifacts (PA), the time to acquire a stable image, and the duration of stable imaging were assessed in healthy volunteers. To demonstrate the clinical applicability of the SDF setup in combination with the IAS, simultaneous bilateral sublingual imaging of the microcirculation were performed during a lung recruitment maneuver (LRM) in mechanically ventilated critically ill patients. One SDF device was operated handheld; the second was fitted with the IAS and held in position by a mechanic arm. Lateral drift, number of losses of image stability and duration of stable imaging of the two methods were compared. Five healthy volunteers were studied. The IAS did not affect microcirculatory flow velocities. A significantly greater force had to applied onto the tissue to induced PA with compared to without IAS (0.25 +/- 0.15 N without vs. 0.62 +/- 0.05 N with the IAS, p < 0.001). The IAS ensured an increased duration of a stable image sequence (8 +/- 2 s without vs. 42 +/- 8 s with the IAS, p < 0.001). The time required to obtain a stable image sequence was similar with and without the IAS. In eight mechanically ventilated patients undergoing a LRM the use of the IAS resulted in a significantly reduced image drifting and enabled the acquisition of significantly longer stable image sequences (24 +/- 5 s without vs. 67 +/- 14 s with the IAS, p = 0.006). The present study has validated the use of an IAS for improvement of SDF imaging by demonstrating that the IAS did not affect microcirculatory perfusion in the microscopic field of view. The IAS improved both axial and lateral SDF image stability and thereby increased the critical force required to induce pressure artifacts. The IAS ensured a significantly increased duration of maintaining a stable image sequence.

Human ESCs predisposition to karyotypic instability: Is a matter of culture adaptation or differential vulnerability among hESC lines due to inherent properties?

PubMed

Catalina, Puri; Montes, Rosa; Ligero, Gertru; Sanchez, Laura; de la Cueva, Teresa; Bueno, Clara; Leone, Paola E; Menendez, Pablo

2008-10-03

The use of human embryonic stem cells (hESCs) in research is increasing and hESCs hold the promise for many biological, clinical and toxicological studies. Human ESCs are expected to be chromosomally stable since karyotypic changes represent a pitfall for potential future applications. Recently, several studies have analysed the genomic stability of several hESC lines maintained after prolonged in vitro culture but controversial data has been reported. Here, we prompted to compare the chromosomal stability of three hESC lines maintained in the same laboratory using identical culture conditions and passaging methods. Molecular cytogenetic analyses performed in three different hESC lines maintained in parallel in identical culture conditions revealed significant differences among them in regard to their chromosomal integrity. In feeders, the HS181, SHEF-1 and SHEF-3 hESC lines were chromosomally stable up to 185 passages using either mechanical or enzymatic dissection methods. Despite the three hESC lines were maintained under identical conditions, each hESC line behaved differently upon being transferred to a feeder-free culture system. The two younger hESC lines, HS181 (71 passages) and SHEF-3 (51 passages) became chromosomally unstable shortly after being cultured in feeder-free conditions. The HS181 line gained a chromosome 12 by passage 17 and a marker by passage 21, characterized as a gain of chromosome 20 by SKY. Importantly, the mosaicism for trisomy 12 gradually increased up to 89% by passage 30, suggesting that this karyotypic abnormality provides a selective advantage. Similarly, the SHEF-3 line also acquired a trisomy of chromosome 14 as early as passage 10. However, this karyotypic aberration did not confer selective advantage to the genetically abnormal cells within the bulk culture and the level of mosaicism for the trisomy 14 remained overtime between 15%-36%. Strikingly, however, a much older hESC line, SHEF-1, which was maintained for 185 passages in feeders did not undergo any numerical or structural chromosomal change after 30 passages in feeder-free culture and over 215 passages in total. These results support the concept that feeder-free conditions may partially contribute to hESC chromosomal changes but also confirm the hypothesis that regardless of the culture conditions, culture duration or splitting methods, some hESC lines are inherently more prone than others to karyotypic instability.

Picometer resolution interferometric characterization of the dimensional stability of zero CTE CFRP

NASA Astrophysics Data System (ADS)

Cordero Machado, Jorge; Heinrich, Thomas; Schuldt, Thilo; Gohlke, Martin; Lucarelli, Stefano; Weise, Dennis; Johann, Ulrich; Peters, Achim; Braxmaier, Claus

2008-07-01

Highly stable but lightweight structural materials are essential for the realization of spaceborne optical instruments, for example telescopes. In terms of optical performance, usually tight tolerances on the absolute spacing between telescope mirrors have to be maintained from integration on ground to operation in final orbit. Furthermore, a certain stability of the telescope structure must typically be ensured in the measurement band. Particular challenging requirements have to be met for the LISA Mission (Laser Interferometer Space Antenna), where the spacing between primary and secondary mirror must be stable to a few picometers. Only few materials offer sufficient thermal stability to provide such performance. Candidates are for example Zerodur and Carbon-Fiber Reinforced Plastic (CFRP), where the latter is preferred in terms of mechanical stiffness and robustness. We are currently investigating the suitability of CFRP with respect to the LISA requirements by characterization of its dimensional stability with heterodyne laser interferometry. The special, highly symmetric interferometer setup offers a noise level of 2 pm/√Hz at 0.1Hz and above, and therefore represents a unique tool for this purpose. Various procedures for the determination of the coefficient of thermal expansion (CTE) have been investigated, both on a test sample with negative CTE, as well as on a CFRP tube specifically tuned to provide a theoretical zero expansion in the axial dimension.

Efficient high-harmonic generation from a stable and compact ultrafast Yb-fiber laser producing 100 μJ, 350 fs pulses based on bendable photonic crystal fiber

NASA Astrophysics Data System (ADS)

Feehan, James S.; Price, Jonathan H. V.; Butcher, Thomas J.; Brocklesby, William S.; Frey, Jeremy G.; Richardson, David J.

2017-01-01

The development of an Yb3+-fiber-based chirped-pulse amplification system and the performance in the generation of extreme ultraviolet (EUV) radiation by high-harmonic generation is reported. The fiber laser produced 100 μJ, 350 fs output pulses with diffraction-limited beam quality at a repetition rate of 16.7 kHz. The system used commercial single-mode, polarization maintaining fiber technology. This included a 40 μm core, easily packaged, bendable final amplifier fiber in order to enable a compact system, to reduce cost, and provide reliable and environmentally stable long-term performance. The system enabled the generation of 0.4 μW of EUV at wavelengths between 27 and 80 nm with a peak at 45 nm using xenon gas. The EUV flux of 1011 photons per second for a driving field power of 1.67 W represents state-of-the-art generation efficiency for single-fiber amplifier CPA systems, corresponding to a maximum calculated energy conversion efficiency of 2.4 × 10-7 from the infrared to the EUV. The potential for high average power operation at increased repetition rates and further suggested technical improvements are discussed. Future applications could include coherent diffractive imaging in the EUV, and high-harmonic spectroscopy.

Numerical Investigation of Hydrogen and Kerosene Combustion in Supersonic Air Streams

NASA Technical Reports Server (NTRS)

Taha, A. A.; Tiwari, S. N.; Mohieldin, T. O.

1999-01-01

The effect of mixing schemes on the combustion of both gaseous hydrogen and liquid kerosene is investigated. Injecting pilot gaseous hydrogen parallel to the supersonic incoming air tends to maintain the stabilization of the main liquid kerosene, which is normally injected. Also the maximum kerosene equivalence ratio that can maintain stable flame can be increased by increasing the pilot energy level. The wedge flame holding contributes to an increased kerosene combustion efficiency by the generation of shock-jet interaction.

Generation of stable PDX derived cell lines using conditional reprogramming.

PubMed

Borodovsky, Alexandra; McQuiston, Travis J; Stetson, Daniel; Ahmed, Ambar; Whitston, David; Zhang, Jingwen; Grondine, Michael; Lawson, Deborah; Challberg, Sharon S; Zinda, Michael; Pollok, Brian A; Dougherty, Brian A; D'Cruz, Celina M

2017-12-06

Efforts to develop effective cancer therapeutics have been hindered by a lack of clinically predictive preclinical models which recapitulate this complex disease. Patient derived xenograft (PDX) models have emerged as valuable tools for translational research but have several practical limitations including lack of sustained growth in vitro. In this study, we utilized Conditional Reprogramming (CR) cell technology- a novel cell culture system facilitating the generation of stable cultures from patient biopsies- to establish PDX-derived cell lines which maintain the characteristics of the parental PDX tumor. Human lung and ovarian PDX tumors were successfully propagated using CR technology to create stable explant cell lines (CR-PDX). These CR-PDX cell lines maintained parental driver mutations and allele frequency without clonal drift. Purified CR-PDX cell lines were amenable to high throughput chemosensitivity screening and in vitro genetic knockdown studies. Additionally, re-implanted CR-PDX cells proliferated to form tumors that retained the growth kinetics, histology, and drug responses of the parental PDX tumor. CR technology can be used to generate and expand stable cell lines from PDX tumors without compromising fundamental biological properties of the model. It offers the ability to expand PDX cells in vitro for subsequent 2D screening assays as well as for use in vivo to reduce variability, animal usage and study costs. The methods and data detailed here provide a platform to generate physiologically relevant and predictive preclinical models to enhance drug discovery efforts.

Coupling the Alkaline-Surfactant-Polymer Technology and The Gelation Technology to Maximize Oil Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malcolm Pitts; Jie Qi; Dan Wilson

2005-12-01

Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or reservoirs with different sand lenses with high permeability contrast. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more crude oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or reservoirs with high permeability contrast zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction withmore » different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium-polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses with the exception of the xanthan gum-chromium acetate gels. Aluminum-polyacrylamide flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9, either in linear corefloods or in dual separate radial core, common manifold corefloods. Chromium acetate-polyacrylamide flowing and rigid tonguing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid tonguing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Chromium acetate gels were stable to injection of alkaline-surfactant-polymer solutions at 72 F, 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetatexanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection at 72, 125, and 175 F. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid tonguing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid tonguing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. Aluminum citrate-polyacrylamide gels, chromium acetate-polyacrylamide gels, silicate-polymer, and chromium-xanthan gum gels did not alter an alkaline-surfactant-polymer solution's ability to produce incremental oil. Incremental oil was reduced with the resorcinol-formaldehyde gel system. Total waterflood plus chemical flood oil recovery sequence recoveries were generally similar. Performance and produced polymer evaluation of four alkaline-surfactant-polymer projects concluded that only one of the projects could have benefited from combining the alkaline-surfactant-polymer and gelation technologies. Cambridge, the 1993 Daqing, Mellott Ranch, and the Wardlaw alkaline-surfacant-polymer floods were studied. An initial gel treatment followed by an alkaline-surfactant-polymer flood in the Wardlaw field would have been a benefit due to reduction of fracture flow.« less

Response of a continuous anaerobic digester to temperature transitions: A critical range for restructuring the microbial community structure and function.

PubMed

Kim, Jaai; Lee, Changsoo

2016-02-01

Temperature is a crucial factor that significantly influences the microbial activity and so the methanation performance of an anaerobic digestion (AD) process. Therefore, how to control the operating temperature for optimal activity of the microbes involved is a key to stable AD. This study examined the response of a continuous anaerobic reactor to a series of temperature shifts over a wide range of 35-65 °C using a dairy-processing byproduct as model wastewater. During the long-term experiment for approximately 16 months, the reactor was subjected to stepwise temperature increases by 5 °C at a fixed HRT of 15 days. The reactor showed stable performance within the temperature range of 35-45 °C, with the methane production rate and yield being maximum at 45 °C (18% and 26% greater, respectively, than at 35 °C). However, the subsequent increase to 50 °C induced a sudden performance deterioration with a complete cessation of methane recovery, indicating that the temperature range between 45 °C and 50 °C had a critical impact on the transition of the reactor's methanogenic activity from mesophilic to thermophilic. This serious process perturbation was associated with a severe restructuring of the reactor microbial community structure, particularly of methanogens, quantitatively as well as qualitatively. Once restored by interrupted feeding for about two months, the reactor maintained fairly stable performance under thermophilic conditions until it was upset again at 65 °C. Interestingly, in contrast to most previous reports, hydrogenotrophs largely dominated the methanogen community at mesophilic temperatures while acetotrophs emerged as a major group at thermophilic temperature. This implies that the primary methanogenesis route of the reactor shifted from hydrogen- to acetate-utilizing pathways with the temperature shifts from mesophilic to thermophilic temperatures. Our observations suggest that a mesophilic digester may not need to be cooled at up to 45 °C in case of undesired temperature rise, for example, by excessive self-heating, which offers a possibility to reduce operating costs. Copyright © 2015 Elsevier Ltd. All rights reserved.

Time-on-task decrement in vigilance is modulated by inter-individual vulnerability to homeostatic sleep pressure manipulation

PubMed Central

Maire, Micheline; Reichert, Carolin F.; Gabel, Virginie; Viola, Antoine U.; Krebs, Julia; Strobel, Werner; Landolt, Hans-Peter; Bachmann, Valérie; Cajochen, Christian; Schmidt, Christina

2014-01-01

Under sleep loss, vigilance is reduced and attentional failures emerge progressively. It becomes difficult to maintain stable performance over time, leading to growing performance variability (i.e., state instability) in an individual and among subjects. Task duration plays a major role in the maintenance of stable vigilance levels, such that the longer the task, the more likely state instability will be observed. Vulnerability to sleep-loss-dependent performance decrements is highly individual and is also modulated by a polymorphism in the human clock gene PERIOD3 (PER3). By combining two different protocols, we manipulated sleep-wake history by once extending wakefulness for 40 h (high sleep pressure condition) and once by imposing a short sleep-wake cycle by alternating 160 min of wakefulness and 80 min naps (low sleep pressure condition) in a within-subject design. We observed that homozygous carriers of the long repeat allele of PER3 (PER35/5) experienced a greater time-on-task dependent performance decrement (i.e., a steeper increase in the number of lapses) in the Psychomotor Vigilance Task compared to the carriers of the short repeat allele (PER34/4). These genotype-dependent effects disappeared under low sleep pressure conditions, and neither motivation, nor perceived effort accounted for these differences. Our data thus suggest that greater sleep-loss related attentional vulnerability based on the PER3 polymorphism is mirrored by a greater state instability under extended wakefulness in the short compared to the long allele carriers. Our results undermine the importance of time-on-task related aspects when investigating inter-individual differences in sleep loss-induced behavioral vulnerability. PMID:24639634

Functional integrity of flexible n-channel metal–oxide–semiconductor field-effect transistors on a reversibly bistable platform

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alfaraj, Nasir; Hussain, Aftab M.; Torres Sevilla, Galo A.

Flexibility can bring a new dimension to state-of-the-art electronics, such as rollable displays and integrated circuit systems being transformed into more powerful resources. Flexible electronics are typically hosted on polymeric substrates. Such substrates can be bent and rolled up, but cannot be independently fixed at the rigid perpendicular position necessary to realize rollable display-integrated gadgets and electronics. A reversibly bistable material can assume two stable states in a reversible way: flexibly rolled state and independently unbent state. Such materials are used in cycling and biking safety wristbands and a variety of ankle bracelets for orthopedic healthcare. They are often wrappedmore » around an object with high impulsive force loading. Here, we study the effects of cumulative impulsive force loading on thinned (25 μm) flexible silicon-based n-channel metal–oxide–semiconductor field-effect transistor devices housed on a reversibly bistable flexible platform. We found that the transistors have maintained their high performance level up to an accumulated 180 kN of impact force loading. The gate dielectric layers have maintained their reliability, which is evidenced by the low leakage current densities. Also, we observed low variation in the effective electron mobility values, which manifests that the device channels have maintained their carrier transport properties.« less

Co-digestion of onion juice and wastewater sludge using an anaerobic mixed biofilm reactor.

PubMed

Romano, Rowena T; Zhang, Ruihong

2008-02-01

The co-digestion of onion juice and aerobic wastewater sludge produced from an onion processor using an anaerobic mixed biofilm reactor (AMBR) was investigated for biogas energy production potential and waste treatment. Two experiments were conducted to study the performance of an AMBR at different organic loading rates (OLRs) using different mixtures of onion juice and aerobic sludge. In the first experiment, the OLR was increased from 1.24 to 4.37 gVS/L/d by increasing the amount of onion juice in the feed mixture while maintaining a constant amount of aerobic sludge. When the OLR reached 4.37 gVS/L/d, the AMBR failed as indicated by decreased biogas production and pH. Increase of carbon to nitrogen ratio (C/N) from 13.7 to 20.3 and lack of proper alkalinity were suspected to be the causes for the failure. In the second experiment, the C/N of the feed mixture was maintained at about 15 while the OLR was increased from 1.40 to 3.60 gVS/L/d. The digester showed stable performance. The average biogas and methane yields of the two experiments were 0.62 +/- 0.05 L/gVS and 0.37 +/- 0.08 L/gVS, respectively. It was concluded that the C/N of about 15 was recommended for treating the mixture of onion juice and aerobic sludge.

The effect of passivation film in preparation 3D structural carbon paper/tin oxide@carbon as freestanding anode for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Deng, Chenfang; Liu, Yang; Lu, Zhongpei; Ma, Chao; Ge, Tao; Li, Weili; Yang, Gang

2018-03-01

Tin-based compounds are potential anode materials for high performance lithium-ion batteries (LIBs). Due to the low melting point of metallic Sn, it is hard to maintain the crystal morphology of Sn during the as-follow process of carbon coating for high performance anode. In this work, the core@shell composite of SnOx@carbon (SnOx@C) is successfully fabricated on the substrate of carbon paper (CP) through electrodeposition and carbonization based on the precursor of Sn nanoparticles. A passivation shell is essentially grown onto Sn particles to obtain a stable structure of SnOx@C, otherwise the Sn particles will be pulverized and fell off the substrate of CP during the subsequent process of carbonization. The as-produced CP/SnOx@C film has excellent flexibility and mechanical stability to be directly served as electrode for LIBs. Carbon shell prevents the detachment and agglomeration of the active particles during lithiation/delithiation processes and maintains the stability of the conductive network. After 100th cycles, CP/SnOx@C electrode delivers 0.8 mAh cm-2, much higher than the capacity 0.37 mAh cm-2 of CP/Sn electrode operated at the current density of 0.1 mA cm-2. These features enable the flexible film of CP/SnOx@C to be attractive applications in energy storage devices.

Intraspecific variation and species coexistence.

PubMed

Lichstein, Jeremy W; Dushoff, Jonathan; Levin, Simon A; Pacala, Stephen W

2007-12-01

We use a two-species model of plant competition to explore the effect of intraspecific variation on community dynamics. The competitive ability ("performance") of each individual is assigned by an independent random draw from a species-specific probability distribution. If the density of individuals competing for open space is high (e.g., because fecundity is high), species with high maximum (or large variance in) performance are favored, while if density is low, species with high typical (e.g., mean) performance are favored. If there is an interspecific mean-variance performance trade-off, stable coexistence can occur across a limited range of intermediate densities, but the stabilizing effect of this trade-off appears to be weak. In the absence of this trade-off, one species is superior. In this case, intraspecific variation can blur interspecific differences (i.e., shift the dynamics toward what would be expected in the neutral case), but the strength of this effect diminishes as competitor density increases. If density is sufficiently high, the inferior species is driven to extinction just as rapidly as in the case where there is no overlap in performance between species. Intraspecific variation can facilitate coexistence, but this may be relatively unimportant in maintaining diversity in most real communities.

Thermodynamic Vent System Performance Testing with Subcooled Liquid Methane and Gaseous Helium Pressurant

NASA Technical Reports Server (NTRS)

Flachbart, R. H.; Hastings, L. J.; Hedayat, A.; Nelson, S. L.; Tucker, S. P.

2007-01-01

Due to its high specific impulse and favorable thermal properties for storage, liquid methane (LCH4) is being considered as a candidate propellant for exploration architectures. In order to gain an -understanding of any unique considerations involving micro-gravity pressure control with LCH4, testing was conducted at the Marshall Space Flight Center using the Multipurpose Hydrogen Test Bed (MHTB) to evaluate the performance of a spray-bar thermodynamic vent system (TVS) with subcooled LCH4 and gaseous helium (GHe) pressurant. Thirteen days of testing were performed in November 2006, with total tank heat leak conditions of about 715 W and 420 W at a fill level of approximately 90%. The TVS system was used to subcool the LCH4 to a liquid saturation pressure of approximately 55.2 kPa before the tank was pressurized with GHe to a total pressure of 165.5 kPa. A total of 23 TVS cycles were completed. The TVS successfully controlled the ullage pressure within a prescribed control band but did not maintain a stable liquid saturation pressure. This was likely. due to a TVS design not optimized for this particular propellant and test conditions, and possibly due to a large artificially induced heat input directly into the liquid. The capability to reduce liquid saturation pressure as well as maintain it within a prescribed control band, demonstrated that the TVS could be used to seek and maintain a desired liquid inlet temperature for an engine (at a cost of propellant lost through the TVS vent). One special test was conducted at the conclusion of the planned test activities. Reduction of the tank ullage pressure by opening the Joule-Thomson valve (JT) without operating the pump was attempted. The JT remained open for over 9300 seconds, resulting in an ullage pressure reduction of 30 kPa. The special test demonstrated the feasibility of using the JT valve for limited ullage pressure reduction in the event of a pump failure.

A prospective, within-patient, crossover study of continuous intravenous and subcutaneous morphine for chronic cancer pain.

PubMed

Nelson, K A; Glare, P A; Walsh, D; Groh, E S

1997-05-01

The dose, efficacy, and side effects of continuous intravenous infusion (CIVI) of morphine were compared with continuous subcutaneous infusion (CSCI) of morphine in patients with chronic cancer pain. Eligible patients were referred to the Palliative Care Program and were receiving a stable dose of CIVI of morphine. The design was a within-patient, one-way crossover; in which each patient provided data before and after a switch from CIVI to CSCI of morphine. "Rescue" doses were 50% of the hourly dose given every 2 hours as needed. Morphine was infused intravenously (i.v.) and subcutaneously (s.c.) via a McGaw/AccuPro Volumetric Infusion Pump. After baseline data, including side effects and pain assessment, were obtained, patients were evaluated twice daily for toxicity and analgesic efficacy. Those who had a stable CIVI dose for 48 consecutive hr were crossed over to the CSCI at the same dose as the intravenous (i.v.) phase. A stable dose was defined as no dose change, four or less rescue doses in the previous 24 hr, and a pain rating of none or mild. CIVI was considered equal to CSCI if these criteria were maintained for 96 consecutive hr. Fifty-seven patients were entered, and 40 were evaluable (15 women and 25 men). The median age was 67 (range 30-83 years). All 40 participants, after maintaining a stable dose throughout the i.v. phase, crossed to the s.c. phase and remained on s.c. for at least 48 hr. Thirty-two patients maintained a stable dose throughout the i.v. and s.c. phases. The mean stable i.v. dose (day 2) was 5.05 mg/hr, and the mean stable s.c. dose (day 4) was 5.7 mg/hr (P = 0.01). The mean number of rescue doses on day 2 was 0.83 per 24 hr versus 0.80 per 24 hours on day 4 (P = 0.6). The mean categorical pain score on day 2 was 0.83, and on day 4, 0.85 (P = 0.7). The mean visual analogue scale (VAS) on day 2 was 22.9 mm versus 17.6 mm on day 4 (P = 0.1). The mean incidence of side effects on day 2 was 1.7, and on day 4, 2.0 (P = 0.2). No patient was withdrawn or had a dose reduction due to unacceptable toxicity. There were two reports of local toxicity (mild erythema) at the SC needle insertion point, which required a site change. All of our 40 patients had adequate pain control with CIVI and CSCI morphine. Of the eight participants who were not maintained on the same i.v. and s.c. dose, all had adequate pain control and a similar side-effect profile on a higher s.c. morphine dose. These data suggest that the i.v. and s.c. routes are equianalgesic for most patients when administered as a continuous infusion. Pain control and side-effect profiles are quite similar and acceptable. s.c. morphine is an excellent alternative to i.v. morphine in both inpatients and outpatients requiring parenteral morphine for pain.

Genome accessibility is widely preserved and locally modulated during mitosis.

PubMed

Hsiung, Chris C-S; Morrissey, Christapher S; Udugama, Maheshi; Frank, Christopher L; Keller, Cheryl A; Baek, Songjoon; Giardine, Belinda; Crawford, Gregory E; Sung, Myong-Hee; Hardison, Ross C; Blobel, Gerd A

2015-02-01

Mitosis entails global alterations to chromosome structure and nuclear architecture, concomitant with transient silencing of transcription. How cells transmit transcriptional states through mitosis remains incompletely understood. While many nuclear factors dissociate from mitotic chromosomes, the observation that certain nuclear factors and chromatin features remain associated with individual loci during mitosis originated the hypothesis that such mitotically retained molecular signatures could provide transcriptional memory through mitosis. To understand the role of chromatin structure in mitotic memory, we performed the first genome-wide comparison of DNase I sensitivity of chromatin in mitosis and interphase, using a murine erythroblast model. Despite chromosome condensation during mitosis visible by microscopy, the landscape of chromatin accessibility at the macromolecular level is largely unaltered. However, mitotic chromatin accessibility is locally dynamic, with individual loci maintaining none, some, or all of their interphase accessibility. Mitotic reduction in accessibility occurs primarily within narrow, highly DNase hypersensitive sites that frequently coincide with transcription factor binding sites, whereas broader domains of moderate accessibility tend to be more stable. In mitosis, proximal promoters generally maintain their accessibility more strongly, whereas distal regulatory elements tend to lose accessibility. Large domains of DNA hypomethylation mark a subset of promoters that retain accessibility during mitosis and across many cell types in interphase. Erythroid transcription factor GATA1 exerts site-specific changes in interphase accessibility that are most pronounced at distal regulatory elements, but has little influence on mitotic accessibility. We conclude that features of open chromatin are remarkably stable through mitosis, but are modulated at the level of individual genes and regulatory elements. © 2015 Hsiung et al.; Published by Cold Spring Harbor Laboratory Press.

Stability of extemporaneously compounded dexamethasone in glass and plastic bottles and plastic syringes.

PubMed

Ensom, Mary H H; Décarie, Diane

2014-07-01

Dexamethasone is widely used to treat rheumatic and endocrine disorders and chemotherapy-induced nausea and vomiting. A palatable, alcohol-free liquid formulation, with a suitable concentration to allow reasonable administration volume, is available only via extemporaneous compounding. To evaluate the stability of dexamethasone suspensions in commercially available vehicles (Oral Mix and Oral Mix SF) in various types of containers after storage at 25°C and 4°C for up to 91 days. Dexamethasone suspensions (1 mg/mL) were prepared in Oral Mix and Oral Mix SF and then transferred to amber glass and plastic prescription bottles and plastic oral syringes. Suspensions in all 3 types of containers were stored at 25°C; suspensions in glass and plastic bottles were also stored at 4°C. Samples were collected weekly from each container up to 28 days and then every 2 weeks up to 91 days. The samples were analyzed by a validated, stability-indicating high-performance liquid chromatography - ultraviolet detection method. A suspension was considered stable if it maintained at least 90% of its initial dexamethasone concentration. Changes in colour, taste, odour, precipitation (and ease of resuspension), and pH were used to assess physical compatibility. All suspensions maintained at least 96% of the original concentration for up to 91 days with storage at 25°C or at 4°C. No notable changes in colour, taste, odour, precipitation, or pH were observed over the 91-day period. Dexamethasone suspensions (1 mg/mL) in Oral Mix and Oral Mix SF, stored in amber glass or plastic bottles or plastic syringes at 25°C or in amber glass or plastic bottles at 4°C can be expected to remain stable for up to 91 days.

Risk of Porphyromonas gingivalis recolonization during the early period of periodontal maintenance in initially severe periodontitis sites.

PubMed

Fujise, Osamu; Miura, Mayumi; Hamachi, Takafumi; Maeda, Katsumasa

2006-08-01

Porphyromonas gingivalis is considered a critical pathogen of periodontal diseases including recurrent periodontitis. The profound effects of active periodontal treatment (APT) on P. gingivalis elimination were previously demonstrated and revealed that the subsequent P. gingivalis-free or -suppressed status seems to be maintained during early periodontal maintenance (PMT). The aim of the present study was to show the occurrence of microbial recolonization during this early PMT period. In total, 128 sites from 11 generalized chronic periodontitis patients and one generalized aggressive periodontitis patient underwent clinical and microbiologic examination at baseline (Exam-I), after APT (Exam-II), and in PMT (Exam-III). Exam-III was carried out an average of 4.5 +/- 3.5 months after Exam-II. Detection and quantification of putative pathogens were performed using a polymerase chain reaction-based method. The PMT used was effective in maintaining the clinical conditions improved by APT. However, in microbiological examinations, Exam-III showed higher detection frequency and levels of P. gingivalis than Exam-II. This suggests that a P. gingivalis recolonization started in the early PMT period. P. gingivalis-increased sites then showed significantly more severe signs of periodontitis in Exam-I than P. gingivalis-stable sites (bleeding on probing frequency: 76.7% versus 56.5%; suppuration frequency: 41.9% versus 12.9%). On the other hand, in Exam-II, no significant differences of clinical parameters were noted between P. gingivalis-increased and -stable sites. Severe periodontitis sites before APT seemed to place them at risk of P. gingivalis recolonization in the early PMT period, and this microbial restoration could be a cause of recurrent periodontitis.

LCL: (Locked Cheek Lift) Three-Dimensional Cheek Lift and Inferior Palpebral Rejuvenation.

PubMed

Divaris, Marc; Sabri, Ebaa; Cancemi, Gianfranco; Daury, Richard

2018-06-01

Many recent advances in face lift techniques have been made to reverse the aging process of the mid-face. In this study, we present a new technique by which mid-face rejuvenation can be achieved in double-angle vectors and allows adaption to the underlying bony structure. The locked cheek lift (LCL) allows effective, simple and rapid lifting of the malar fat pad in two planes. Correction of the curvature of the face and reduction of the height of lid cheek junction distance can be achieved without an incision at the lower eyelid. In total, 115 patients (77 females and 38 males) have been operated on using the LCL technique by a single surgeon; patient ages ranged between 37 and 71 years old (average = 51). Follow-up was performed by the same team for a year postoperatively. The facial expression and lid cheek distance have been evaluated during this period. After a year from the operation, the lid cheek distance correction was maintained in 95.7% of the cases, with stable position of the ascended malar fat pad. Postoperative edema and ecchymosis were limited. LCL is an effective, simple and rapid surgical technique, which is capable of correcting the cheek gravitational migration, reducing the lid cheek distance (LCD), maintaining the ascended stable malar fat pad for a long time with a short recovery period and minimal risk of complications. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Self-Efficacy as a Marker of Cardiac Function and Predictor of Heart Failure Hospitalization and Mortality in Patients With Stable Coronary Heart Disease: Findings From the Heart and Soul Study

PubMed Central

Sarkar, Urmimala; Ali, Sadia; Whooley, Mary A.

2009-01-01

Objective The authors sought to evaluate the association of self-efficacy with objective measures of cardiac function, subsequent hospitalization for heart failure (HF), and all-cause mortality. Design Observational cohort of ambulatory patients with stable CHD. The authors measured self-efficacy using a published, validated, 5-item summative scale, the Sullivan Self-Efficacy to Maintain Function Scale. The authors also performed a cardiac assessment, including an exercise treadmill test with stress echocardiography. Main Outcome Measures Hospitalizations for HF, as determined by blinded review of medical records, and all-cause mortality, with adjustment for demographics, medical history, medication use, depressive symptoms, and social support. Results Of the 1,024 predominately male, older CHD patients, 1013 (99%) were available for follow-up, 124 (12%) were hospitalized for HF, and 235 (23%) died during 4.3 years of follow-up. Mean cardiac self-efficacy score was 9.7 (SD 4.5, range 0–20), corresponding to responses between “not at all confident” and “somewhat confident” for ability to maintain function. Lower self-efficacy predicted subsequent HF hospitalization (OR per SD decrease = 1.4, p = 0006), and all-cause mortality (OR per SD decrease = 1.4, p < .0001). After adjustment, the association of cardiac self-efficacy with both HF hospitalization and mortality was explained by worse baseline cardiac function. Conclusion Among patients with CHD, self-efficacy was a reasonable proxy for predicting HF hospitalizations. The increased risk of HF associated with lower baseline self-efficacy was explained by worse cardiac function. These findings indicate that measuring cardiac self-efficacy provides a rapid and potentially useful assessment of cardiac function among outpatients with CHD. PMID:19290708

Fish bioconcentration studies with column-generated analyte concentrations of highly hydrophobic organic chemicals.

PubMed

Schlechtriem, Christian; Böhm, Leonard; Bebon, Rebecca; Bruckert, Hans-Jörg; Düring, Rolf-Alexander

2017-04-01

The performance of aqueous exposure bioconcentration fish tests according to Organisation for Economic Co-operation and Development (OECD) guideline 305 requires the possibility of preparing stable aqueous concentrations of the test substances. For highly hydrophobic organic chemicals (HOCs; octanol-water partition coefficient [log K OW ] > 5), testing via aqueous exposure may become increasingly difficult. A solid-phase desorption dosing system was developed to generate stable concentrations of HOCs without using solubilizing agents. The system was tested with hexachlorobenzene (HCB), o-terphenyl (oTP), polychlorinated biphenyl (PCB) 153, and dibenz[a,h]anthracene (DBA) (log K OW 5.5-7.8) in 2 flow-through fish tests with rainbow trout (Oncorhynchus mykiss). The analysis of the test media applied during the bioconcentration factor (BCF) studies showed that stable analyte concentrations of the 4 HOCs were maintained in the test system over an uptake period of 8 wk. Bioconcentration factors (L kg -1 wet wt) were estimated for HCB (BCF 35 589), oTP (BCF 12 040), and PCB 153 (BCF 18 539) based on total water concentrations. No bioconcentration could be determined for DBA, probably because of the rapid metabolism of the test item. The solid-phase desorption dosing system is suitable to provide stable aqueous concentrations of HOCs required to determine the bioconcentration in fish and represents a viable alternative to the use of solubilizing agents for the preparation of test solutions. Environ Toxicol Chem 2017;36:906-916. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC. © 2016 The Authors. Environmental Toxicology and Chemistry Published by Wiley Periodicals, Inc. on behalf of SETAC.

Highly stable maintenance of a mouse artificial chromosome in human cells and mice.

PubMed

Kazuki, Kanako; Takehara, Shoko; Uno, Narumi; Imaoka, Natsuko; Abe, Satoshi; Takiguchi, Masato; Hiramatsu, Kei; Oshimura, Mitsuo; Kazuki, Yasuhiro

2013-12-06

Human artificial chromosomes (HACs) and mouse artificial chromosomes (MACs) display several advantages as gene delivery vectors, such as stable episomal maintenance that avoids insertional mutations and the ability to carry large gene inserts including the regulatory elements. Previously, we showed that a MAC vector developed from a natural mouse chromosome by chromosome engineering was more stably maintained in adult tissues and hematopoietic cells in mice than HAC vectors. In this study, to expand the utility for a gene delivery vector in human cells and mice, we investigated the long-term stability of the MACs in cultured human cells and transchromosomic mice. We also investigated the chromosomal copy number-dependent expression of genes on the MACs in mice. The MAC was stably maintained in human HT1080 cells in vitro during long-term culture. The MAC was stably maintained at least to the F8 and F4 generations in ICR and C57BL/6 backgrounds, respectively. The MAC was also stably maintained in hematopoietic cells and tissues derived from old mice. Transchromosomic mice containing two or four copies of the MAC were generated by breeding. The DNA contents were comparable to the copy number of the MACs in each tissue examined, and the expression of the EGFP gene on the MAC was dependent on the chromosomal copy number. Therefore, the MAC vector may be useful not only for gene delivery in mammalian cells but also for animal transgenesis. Copyright © 2013 Elsevier Inc. All rights reserved.

Stable transformation of Pleurotus ostreatus to hygromycin B resistance using Lentinus edodes GPD expression signals.

PubMed

Irie, T; Honda, Y; Hirano, T; Sato, T; Enei, H; Watanabe, T; Kuwahara, M

2001-09-01

It was reported that Pleurotus ostreatus was transformed unstably using recombinant plasmids containing a hygromycin B phosphotransferase gene (hph) under the control of Aspergillus nidulans expression signals, and that the plasmids were maintained extrachromosomally in the transformants. Here we report a stable and integrative transformation of the fungus to hygromycin B resistance, using a recombinant hph fused with Lentinus edodes glyceraldehyde-3-phosphate dehydrogenase expression signals. Restriction-enzyme-mediated integration (REMI) was also tried and increased the transformation efficiency about ten-fold.

Ambient-Stable and Durable Conductive Ag-Nanowire-Network 2-D Films Decorated with a Ti Layer.

PubMed

Kim, Yoon-Mi; Hwang, Bu-Yeon; Lee, Ki-Wook; Kim, Jin-Yeol

2018-05-11

Highly stable and durable conductive silver nanowire (Ag NW) network electrode films were prepared through decoration with a 5-nm-thick Ti layer. The Ag NW network 2-D films showed sheet resistance values as low as 32 ohm/sq at 88% transparency when decorated with Ti. These 2-D films exhibited a 30% increase in electrical conductivity while maintaining good stability of the films through enhanced resistance to moisture and oxygen penetration as a result of the protective effect of the Ti layer.

Opting out against defection leads to stable coexistence with cooperation.

PubMed

Zhang, Bo-Yu; Fan, Song-Jia; Li, Cong; Zheng, Xiu-Deng; Bao, Jian-Zhang; Cressman, Ross; Tao, Yi

2016-10-24

Cooperation coexisting with defection is a common phenomenon in nature and human society. Previous studies for promoting cooperation based on kin selection, direct and indirect reciprocity, graph selection and group selection have provided conditions that cooperators outcompete defectors. However, a simple mechanism of the long-term stable coexistence of cooperation and defection is still lacking. To reveal the effect of direct reciprocity on the coexistence of cooperation and defection, we conducted a simple experiment based on the Prisoner's Dilemma (PD) game, where the basic idea behind our experiment is that all players in a PD game should prefer a cooperator as an opponent. Our experimental and theoretical results show clearly that the strategies allowing opting out against defection are able to maintain this stable coexistence.

Stable high absorption metamaterial for wide-angle incidence of terahertz wave

NASA Astrophysics Data System (ADS)

Du, Qiujiao; Zeng, Zuoxun; Xiang, Dong; Lv, Tao; Zhang, Guangyong; Yang, Hongwu

2014-04-01

We propose a metamaterial based on metallic Jerusalem cross and cross-wire structures for realizing relatively stable high absorption with respect to the wide angle incidence of both polarized terahertz (THz) waves. Numerical simulations are carried out to verify the proposed absorber. For both transverse electric and transverse magnetic polarizations, absorptions around 0.93 THz reach nearly up to unity under normal incidence and maintain above 97% over a wide incidence angle range. The THz absorber can be easily micro-fabricated due to a thickness about 40 times smaller than operating wavelength. The proposed metamaterial is a promising candidate as absorbing element in THz thermal imager, due to its wide angle, stable high absorption and very thin thickness.

MBE growth technology for high quality strained III-V layers

NASA Technical Reports Server (NTRS)

Grunthaner, Frank J. (Inventor); Liu, John K. (Inventor); Hancock, Bruce R. (Inventor)

1990-01-01

The III-V films are grown on large automatically perfect terraces of III-V substrates which have a different lattice constant, with temperature and Group III and V arrival rates chosen to give a Group III element stable surface. The growth is pulsed to inhibit Group III metal accumulation of low temperature, and to permit the film to relax to equilibrium. The method of the invention: (1) minimizes starting step density on sample surface; (2) deposits InAs and GaAs using an interrupted growth mode (0.25 to 2 monolayers at a time); (3) maintains the instantaneous surface stoichiometry during growth (As-stable for GaAs, In-stable for InAs); and (4) uses time-resolved RHEED to achieve aspects (1) through (3).

Why Excess Immigration Damages the Environment.

ERIC Educational Resources Information Center

Population-Environment Balance

1992-01-01

Explores the relationship between excessive immigration and environmental degradation. Explains the position that a stable United States population size is essential in prevention further deterioration of the natural resource base. Maintains that balancing immigration and emigration will be instrumental in balancing population with environment.…

Steady-state inductive spheromak operation

DOEpatents

Janos, A.C.; Jardin, S.C.; Yamada, M.

1985-02-20

The inductively formed spheromak configuration (S-1) can be maintained in a highly stable and controlled fashion. The method described eliminates the restriction to pulsed spheromak plasmas or the use of electrodes for steady-state operation, and, therefore, is a reactor-relevant formation and sustainment method.

Evaluation of Laser Stabilization and Imaging Systems for LCLS-II - Final Paper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barry, Matthew

2015-08-20

By combining the top performing commercial laser beam stabilization system with the most ideal optical imaging configuration, the beamline for the Linear Accelerator Coherent Light Source II (LCLS-II) will deliver the highest quality and most stable beam to the cathode. To determine the optimal combination, LCLS-II beamline conditions were replicated and the systems tested with a He-Ne laser. The Guidestar-II and MRC active laser beam stabilization systems were evaluated for their ideal positioning and stability. Both a two and four lens optical imaging configuration was then evaluated for beam imaging quality, magnification properties, and natural stability. In their best performancesmore » when tested over fifteen hours, Guidestar-II kept the beam stable over approximately 70-110um while the MRC system kept it stable over approximately 90-100um. During short periods of time, Guidestar-II kept the beam stable between 10-20um, but was more susceptible to drift over time, while the MRC system maintained the beam between 30-50um with less overall drift. The best optical imaging configuration proved to be a four lens system that images to the iris located in the cathode room and from there, imaged to the cathode. The magnification from the iris to the cathode was 2:1, within an acceptable tolerance to the expected 2.1:1 magnification. The two lens configuration was slightly more stable in small periods of time (less than 10 minutes) without the assistance of a stability system, approximately 55um compared to approximately 70um, but the four lens configurations beam image had a significantly flatter intensity distribution compared to the two lens configuration which had a Gaussian distribution. A final test still needs to be run with both stability systems running at the same time through the four lens system. With this data, the optimal laser beam stabilization system can be determined for the beamline of LCLS-II.« less

Emergence of Adaptive Computation by Single Neurons in the Developing Cortex

PubMed Central

Famulare, Michael; Gjorgjieva, Julijana; Moody, William J.

2013-01-01

Adaptation is a fundamental computational motif in neural processing. To maintain stable perception in the face of rapidly shifting input, neural systems must extract relevant information from background fluctuations under many different contexts. Many neural systems are able to adjust their input–output properties such that an input's ability to trigger a response depends on the size of that input relative to its local statistical context. This “gain-scaling” strategy has been shown to be an efficient coding strategy. We report here that this property emerges during early development as an intrinsic property of single neurons in mouse sensorimotor cortex, coinciding with the disappearance of spontaneous waves of network activity, and can be modulated by changing the balance of spike-generating currents. Simultaneously, developing neurons move toward a common intrinsic operating point and a stable ratio of spike-generating currents. This developmental trajectory occurs in the absence of sensory input or spontaneous network activity. Through a combination of electrophysiology and modeling, we demonstrate that developing cortical neurons develop the ability to perform nearly perfect gain scaling by virtue of the maturing spike-generating currents alone. We use reduced single neuron models to identify the conditions for this property to hold. PMID:23884925

Sea-Sponge-like Structure of Nano-Fe3O4 on Skeleton-C with Long Cycle Life under High Rate for Li-Ion Batteries.

PubMed

Chen, Shipei; Wu, Qingnan; Wen, Ming; Wu, Qingsheng; Li, Jiaqi; Cui, Yi; Pinna, Nicola; Fan, Yafei; Wu, Tong

2018-06-13

To meet the demands of long cycle life under high rate for lithium-ion batteries, the advancement of anode materials with stable structural properties is necessarily demanded. Such promotion needs to design reasonable structure to facilitate the transportation of electron and lithium ions (Li + ). Herein, a novel C/Fe 3 O 4 sea-sponge-like structure was synthesized by ultrasonic spray pyrolysis following thermal decomposition process. On the basis of sea-sponge carbon (SSC) excellences in electronic conductivity and short Li + diffusion pathway, nano-Fe 3 O 4 anchored on stable SSC skeleton can deliver high electrochemical performance with long cycle life under high rate. During electrochemical cycling, well-dispersed nano-Fe 3 O 4 in ∼6 nm not only averts excessive pulverization and is enveloped by solid electrolyte interphase film, but also increases Li + diffusion efficiency. The much improved electrochemical properties showed a capacity of around 460 mAh g -1 at a high rate of 1.5C with a retention rate of 93%, which is maintained without degradation up to 1000 cycles (1C = 1000 mA g -1 ).

Nickel Ferrite Nanoparticles Anchored onto Silica Nanofibers for Designing Magnetic and Flexible Nanofibrous Membranes.

PubMed

Hong, Feifei; Yan, Chengcheng; Si, Yang; He, Jianxin; Yu, Jianyong; Ding, Bin

2015-09-16

Many applications proposed for magnetic silica nanofibers require their assembly into a cellular membrane structure. The feature to keep structure stable upon large deformation is crucial for a macroscopic porous material which functions reliably. However, it remains a key issue to realize robust flexibility in two-dimensional (2D) magnetic silica nanofibrous networks. Here, we report that the combination of electrospun silica nanofibers with zein dip-coating can lead to the formation of flexible, magnetic, and hierarchical porous silica nanofibrous membranes (SNM). The 290 nm diameter silica nanofibers act as templates for the uniform anchoring of nickel ferrite nanoparticles (size of 50 nm). Benefiting from the homogeneous and stable nanofiber-nanoparticle composite structure, the resulting magnetic SNM can maintain their structure integrity under repeated bending as high as 180° and can facilely recover. The unique hierarchical structure also provides this new class of silica membrane with integrated properties of ultralow density, high porosity, large surface area, good magnetic responsiveness, robust dye adsorption capacity, and effective emulsion separation performance. Significantly, the synthesis of such fascinating membranes may provide new insight for further application of silica in a self-supporting, structurally adaptive, and 2D membrane form.

Switching Stable Kidney Transplant Recipients to a Generic Tacrolimus Is Feasible and Safe, but It Must Be Monitored

PubMed Central

López, René; Arriagada, Elizabeth; Carrasco, René; Gallardo, Natalia; Lorca, Eduardo

2017-01-01

Background. Tacrolimus is the primary immunosuppressive drug used in kidney transplant patients. Replacing brand name products with generics is a controversial issue that we studied after a Chilean Ministry of Health mandate to implement such a switch. Methods. Forty-one stable Prograf (Astellas) receiving kidney transplant patients were switched to a generic tacrolimus (Sandoz) in a 1 : 1 dose ratio and were followed up for up to 8 months. All other drugs were maintained as per normal practice. Results. Neither tacrolimus doses nor their trough blood levels changed significantly after the switch, but serum creatinine did: 1.62 ± 0.90 versus 1.75 ± 0.92 mg/dL (p < 0.001). At the same time, five graft biopsies were performed, and two of them showed cellular acute rejection. There were nine infectious episodes treated satisfactorily with proper therapies. No patient or graft was lost during the follow-up time period. Conclusion. Switching from brand name tacrolimus to a generic tacrolimus (Sandoz) is feasible and appears to be safe, but it must be monitored carefully by treating physicians. PMID:28246556

Switching Stable Kidney Transplant Recipients to a Generic Tacrolimus Is Feasible and Safe, but It Must Be Monitored.

PubMed

González, Fernando; López, René; Arriagada, Elizabeth; Carrasco, René; Gallardo, Natalia; Lorca, Eduardo

2017-01-01

Background . Tacrolimus is the primary immunosuppressive drug used in kidney transplant patients. Replacing brand name products with generics is a controversial issue that we studied after a Chilean Ministry of Health mandate to implement such a switch. Methods . Forty-one stable Prograf (Astellas) receiving kidney transplant patients were switched to a generic tacrolimus (Sandoz) in a 1 : 1 dose ratio and were followed up for up to 8 months. All other drugs were maintained as per normal practice. Results . Neither tacrolimus doses nor their trough blood levels changed significantly after the switch, but serum creatinine did: 1.62 ± 0.90 versus 1.75 ± 0.92 mg/dL ( p < 0.001). At the same time, five graft biopsies were performed, and two of them showed cellular acute rejection. There were nine infectious episodes treated satisfactorily with proper therapies. No patient or graft was lost during the follow-up time period. Conclusion . Switching from brand name tacrolimus to a generic tacrolimus (Sandoz) is feasible and appears to be safe, but it must be monitored carefully by treating physicians.

Design for performance enhancement in feedback control systems with multiple saturating nonlinearities. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Kapasouris, Petros

1988-01-01

A systematic control design methodology is introduced for multi-input/multi-output systems with multiple saturations. The methodology can be applied to stable and unstable open loop plants with magnitude and/or rate control saturations and to systems in which state limitations are desired. This new methodology is a substantial improvement over previous heuristic single-input/single-output approaches. The idea is to introduce a supervisor loop so that when the references and/or disturbances are sufficiently small, the control system operates linearly as designed. For signals large enough to cause saturations, the control law is modified in such a way to ensure stability and to preserve, to the extent possible, the behavior of the linear control design. Key benefits of this methodology are: the modified compensator never produces saturating control signals, integrators and/or slow dynamics in the compensator never windup, the directional properties of the controls are maintained, and the closed loop system has certain guaranteed stability properties. The advantages of the new design methodology are illustrated by numerous simulations, including the multivariable longitudinal control of modified models of the F-8 (stable) and F-16 (unstable) aircraft.

On the thermo-chemical origin of the stratified region at the top of the Earth's core

NASA Astrophysics Data System (ADS)

Nakagawa, Takashi

2018-03-01

I developed a combined model of the thermal and chemical evolution of the Earth's core and investigated its influence on a thermochemically stable region beneath the core-mantle boundary (CMB). The chemical effects of the growing stable region are caused by the equilibrium chemical reaction between silicate and the metallic core. The thermal effects can be characterized by the growth of the sub-isentropic shell, which may have a rapid growth rate compared to that of the chemically stable region. When the present-day CMB heat flow was varied, the origin of the stable region changed from chemical to thermochemical to purely thermal because the rapid growth of the sub-isentropic shell can replace the chemically stable region. Physically reasonable values of the present-day CMB heat flow that can maintain the geodynamo action over 4 billion years should be between 8 and 11 TW. To constrain the thickness of the thermochemically stable region beneath the CMB, the chemical diffusivity is important and should be ∼O(10-8) m2/s to obtain a thickness of the thermochemically stable region beneath the CMB consistent with that inferred from geomagnetic secular variations (140 km). However, the strength of the stable region found in this study is too high to be consistent with the constraint on the stability of the stable region inferred from geomagnetic secular variations.

Information dynamics in living systems: prokaryotes, eukaryotes, and cancer.

PubMed

Frieden, B Roy; Gatenby, Robert A

2011-01-01

Living systems use information and energy to maintain stable entropy while far from thermodynamic equilibrium. The underlying first principles have not been established. We propose that stable entropy in living systems, in the absence of thermodynamic equilibrium, requires an information extremum (maximum or minimum), which is invariant to first order perturbations. Proliferation and death represent key feedback mechanisms that promote stability even in a non-equilibrium state. A system moves to low or high information depending on its energy status, as the benefit of information in maintaining and increasing order is balanced against its energy cost. Prokaryotes, which lack specialized energy-producing organelles (mitochondria), are energy-limited and constrained to an information minimum. Acquisition of mitochondria is viewed as a critical evolutionary step that, by allowing eukaryotes to achieve a sufficiently high energy state, permitted a phase transition to an information maximum. This state, in contrast to the prokaryote minima, allowed evolution of complex, multicellular organisms. A special case is a malignant cell, which is modeled as a phase transition from a maximum to minimum information state. The minimum leads to a predicted power-law governing the in situ growth that is confirmed by studies measuring growth of small breast cancers. We find living systems achieve a stable entropic state by maintaining an extreme level of information. The evolutionary divergence of prokaryotes and eukaryotes resulted from acquisition of specialized energy organelles that allowed transition from information minima to maxima, respectively. Carcinogenesis represents a reverse transition: of an information maximum to minimum. The progressive information loss is evident in accumulating mutations, disordered morphology, and functional decline characteristics of human cancers. The findings suggest energy restriction is a critical first step that triggers the genetic mutations that drive somatic evolution of the malignant phenotype.

Performance of WCN diffusion barrier for Cu multilevel interconnects

NASA Astrophysics Data System (ADS)

Lee, Seung Yeon; Ju, Byeong-Kwon; Kim, Yong Tae

2018-04-01

The electrical and thermal properties of a WCN diffusion barrier have been studied for Cu multilevel interconnects. The WCN has been prepared using an atomic layer deposition system with WF6-CH4-NH3-H2 gases and has a very low resistivity of 100 µΩ cm and 96.9% step coverage on the high-aspect-ratio vias. The thermally stable WCN maintains an amorphous state at 800 °C and Cu/WCN contact resistance remains within a 10% deviation from the initial value after 700 °C. The mean time to failure suggests that the Cu/WCN interconnects have a longer lifetime than Cu/TaN and Cu/WN interconnects because WCN prevents Cu migration owing to the stress evolution from tensile to compressive.

A study of X-divertor in NSTX-U with SOLPS simulations

NASA Astrophysics Data System (ADS)

Chen, Zhong-Ping; Kotschenreuther, Mike; Mahajan, Swadesh; Gerhardt, Stefan

2018-03-01

The X-divertor (XD) geometry in NSTX-U is demonstrated, via SOLPS simulations, to perform better than the standard divertor (SD); in particular, it allows detachment at a lower upstream density and stabilizes the detachment front near the target, away from the main X-point. Consequently a stable detached operation becomes possible—the localization near the plate allows a vast reduction of heat fluxes without degrading the core plasma. Indeed, it is confirmed by our simulation that at similar states of detachment the XD outperforms the SD by reducing the heat fluxes to the target and maintaining higher upstream temperatures, resulting in scrape-off layers that are more favorable for advanced tokamak operation. These advantages are attributed to the unique geometric characteristics of XD—poloidal flaring near the target.

Maintaining space shuttle safety within an environment of change

NASA Astrophysics Data System (ADS)

Greenfield, Michael A.

1999-09-01

In the 10 years since the Challenger accident, NASA has developed a set of stable and capable processes to prepare the Space Shuttle for safe launch and return. Capitalizing on the extensive experience gained from a string of over 50 successful flights, NASA today is changing the way it does business in an effort to reduce cost. A single Shuttle Flight Operations Contractor (SFOC) has been chosen to operate the Shuttle. The Government role will change from direct "oversight" to "insight" gained through understanding and measuring the contractor's processes. This paper describes the program management changes underway and the NASA Safety and Mission Assurance (S&MA) organization's philosophy, role, and methodology for pursuing this new approach. It describes how audit and surveillance will replace direct oversight and how meaningful performance metrics will be implemented.

Soft-coupling suspension system for an intradural spinal cord stimulator: Biophysical performance characteristics

NASA Astrophysics Data System (ADS)

Oya, H.; Safayi, S.; Jeffery, N. D.; Viljoen, S.; Reddy, C. G.; Dalm, B. D.; Kanwal, J. K.; Gillies, G. T.; Howard, M. A.

2013-10-01

We have characterized the mechanical compliance of an improved version of the suspension system used to position the electrode-bearing membrane of an intradural neuromodulator on the dorsal pial surface of the spinal cord. Over the compression span of 5 mm, it exhibited a restoring force of 2.4 μN μm-1 and a mean pressure of 0.5 mm Hg (=66 Pa) on the surface below it, well within the range of normal intrathecal pressures. We have implanted prototype devices employing this suspension and a novel device fixation technique in a chronic ovine model of spinal cord stimulation and found that it maintains stable contact at the electrode-pia interface without lead fracture, as determined by measurement of the inter-contact impedances.

Advanced characterization of lithium battery materials with positrons

NASA Astrophysics Data System (ADS)

Barbiellini, Bernardo; Kuriplach, Jan

2017-01-01

Cathode materials are crucial to improved battery performance, in part because there are not yet materials that can maintain high power and stable cycling with a capacity comparable to that of anode materials. Our parameter-free, gradient-corrected model for electron-positron correlations predicts that spectroscopies based on positron annihilation can be deployed to study the effect of lithium intercalation in the oxide matrix of the cathode. The positron characteristics in oxides can be reliably computed using methods based on first-principles. Thus, we can enable a fundamental characterization of lithium battery materials involving positron annihilation spectroscopy and first-principles calculations. The detailed information one can extract from positron experiments could be useful for understanding and optimizing both battery materials and bi-functional catalysts for oxygen reduction and evolution.

Stability analysis of the phytoplankton effect model on changes in nitrogen concentration on integrated multi-trophic aquaculture systems

NASA Astrophysics Data System (ADS)

Widowati; Putro, S. P.; Silfiana

2018-05-01

Integrated Multi-Trophic Aquaculture (IMTA) is a polyculture with several biotas maintained in it to optimize waste recycling as a food source. The interaction between phytoplankton and nitrogen as waste in fish cultivation including ammonia, nitrite, and nitrate studied in the form of mathematical models. The form model is non-linear systems of differential equations with the four variables. The analytical analysis was used to study the dynamic behavior of this model. Local stability analysis is performed at the equilibrium point with the first step linearized model by using Taylor series, then determined the Jacobian matrix. If all eigenvalues have negative real parts, then the equilibrium of the system is locally asymptotic stable. Some numerical simulations were also demonstrated to verify our analytical result.

Reduction of Electrolyte Components on a Coated Si Anode of Lithium-Ion Batteries.

PubMed

Gomez-Ballesteros, Jose L; Balbuena, Perla B

2017-07-20

Surface modification of Si anodes in Li-ion batteries by deposition of a thin alucone coating has demonstrated an effective way to help maintain a stable anode/electrolyte interface and good battery performance. In this work, we investigate the interactions and reactivity of the film with electrolyte components using ab initio molecular dynamics simulations. Adsorption of solvent molecules (ethylene carbonate, EC) and salt (LiPF 6 ) and reduction by two mechanisms depending on the Li content of the film (yielding open EC adsorbed on the film or C 2 H 4 + CO 3 2- ) take place near the film/electrolyte and film/anode interfaces. Reaction products incorporate into the structure of the film and create a new kind of solid-electrolyte interphase layer.

Reduction of Electrolyte Components on a Coated Si Anode of Lithium-Ion Batteries

DOE PAGES

Gomez-Ballesteros, Jose L.; Balbuena, Perla B.

2017-07-07

Surface modification of Si anodes in Li-ion batteries by deposition of a thin alucone coating has demonstrated an effective way to help maintain a stable anode/electrolyte interface and good battery performance. In this paper, we investigate the interactions and reactivity of the film with electrolyte components using ab initio molecular dynamics simulations. Adsorption of solvent molecules (ethylene carbonate, EC) and salt (LiPF 6), and reduction by two mechanisms depending on the Li content of the film (yielding open EC adsorbed on the film or C 2H 4 + CO 3 2-) take place near the film/electrolyte and film/anode interfaces. Finally,more » reactions products incorporate to the structure of the film and create a new kind of solid-electrolyte interphase layer.« less

The Effect of COD Concentration Containing Leaves Litter, Canteen and Composite Waste to the Performance of Solid Phase Microbial Fuel Cell (SMFC)

NASA Astrophysics Data System (ADS)

Samudro, Ganjar; Syafrudin; Nugraha, Winardi Dwi; Sutrisno, Endro; Priyambada, Ika Bagus; Muthi'ah, Hilma; Sinaga, Glory Natalia; Hakiem, Rahmat Tubagus

2018-02-01

This research is conducted to analyze and determine the optimum of COD concentration containing leaves litter, canteen and composite waste to power density and COD removal efficiency as the indicator of SMFC performance. COD as the one of organic matter parameters perform as substrate, nutrient and dominating the whole process of SMFC. Leaves litter and canteen based food waste were obtained from TPST UNDIP in Semarang and treated in SMFC reactor. Its reactor was designed 2 liter volume and equipped by homemade graphene electrodes that were utilized at the surface of organic waste as cathode and in a half of reactor height as anode. COD concentration was initially characterized and became variations of initial COD concentration. Waste volume was maintained 2/3 of volume of reactor. Bacteria sources as the important process factor in SMFC were obtained from river sediment which contain bacteroides and exoelectrogenic bacteria. Temperature and pH were not maintained while power density and COD concentration were periodically observed and measured during 44 days. The results showed that power density up to 4 mW/m2 and COD removal efficiency performance up to 70% were reached by leaves litter, canteen and composite waste at days 11 up to days 44 days. Leaves litter contain 16,567 mg COD/l providing higher COD removal efficiency reached approximately 87.67%, more stable power density reached approximately 4.71 mW/m2, and faster optimum time in the third day than canteen based food waste and composite waste. High COD removal efficiency has not yet resulted in high power density.

Physiological and psychological effects of testosterone during severe energy deficit and recovery: A study protocol for a randomized, placebo-controlled trial for Optimizing Performance for Soldiers (OPS).

PubMed

Pasiakos, Stefan M; Berryman, Claire E; Karl, J Philip; Lieberman, Harris R; Orr, Jeb S; Margolis, Lee M; Caldwell, John A; Young, Andrew J; Montano, Monty A; Evans, William J; Vartanian, Oshin; Carmichael, Owen T; Gadde, Kishore M; Harris, Melissa; Rood, Jennifer C

2017-07-01

The physiological consequences of severe energy deficit include hypogonadism and the loss of fat-free mass. Prolonged energy deficit also impacts physical performance, mood, attentiveness, and decision-making capabilities. This study will determine whether maintaining a eugonadal state during severe, sustained energy deficit attenuates physiological decrements and maintains mental performance. This study will also assess the effects of normalizing testosterone levels during severe energy deficit and recovery on gut health and appetite regulation. Fifty physically active men will participate in a 3-phase, randomized, placebo-controlled study. After completing a 14-d, energy-adequate, diet acclimation phase (protein: 1.6g∙kg -1 ∙d -1 ; fat: 30% total energy intake), participants will be randomized to undergo a 28-d, 55% energy deficit phase with (DEF+TEST: 200mg testosterone enanthate per week) or without (DEF) exogenous testosterone. Diet and physical activity will be rigorously controlled. Recovery from the energy deficit (ad libitum diet, no testosterone) will be assessed until body mass has been recovered within ±2.5% of initial body mass. Body composition, stable isotope methodologies, proteomics, muscle biopsies, whole-room calorimetry, molecular biology, activity/sleep monitoring, personality and cognitive function assessments, functional MRI, and comprehensive biochemistries will be used to assess physiological and psychological responses to energy restriction and recovery feeding while volunteers are in an expected hypogonadal versus eugonadal state. The Optimizing Performance for Soldiers (OPS) study aims to determine whether preventing hypogonadism will mitigate declines in physical and mental function that typically occur during prolonged energy deficit, and the efficacy of testosterone replacement on recovery from severe underfeeding. NCT02734238. Copyright © 2017. Published by Elsevier Inc.

Identification of suitable reference genes for quantitative gene expression analysis in rat adipose stromal cells induced to trilineage differentiation.

PubMed

Santos, Bruno Paiva Dos; da Costa Diesel, Luciana Fraga; da Silva Meirelles, Lindolfo; Nardi, Nance Beyer; Camassola, Melissa

2016-12-15

This study was designed to (i) identify stable reference genes for the analysis of gene expression during in vitro differentiation of rat adipose stromal cells (rASCs), (ii) recommend stable genes for individual treatment conditions, and (iii) validate these genes by comparison with normalization results from stable and unstable reference genes. On the basis of a literature review, eight genes were selected: Actb, B2m, Hprt1, Ppia, Rplp0, Rpl13a, Rpl5, and Ywhaz. Genes were ranked according to their stability under different culture conditions as assessed using GenNorm, NormFinder, and RefFinder algorithms. Although the employed algorithms returned different rankings, the most frequently top-ranked genes were: B2m and/or Ppia for all 28day treatments (ALL28); Ppia and Hprt1 (adipogenic differentiation; A28), B2m (chondrogenic differentiation; C28), Rpl5 (controls maintained in complete culture medium; CCM), Rplp0 (osteogenic differentiation for 3days; O3), Rpl13a and Actb (osteogenic differentiation for 7days; O7), Rplp0 and Ppia (osteogenic differentiation for 14days; O14), Hprt1 and Ppia (osteogenic differentiation for 28days; O28), as well as Actb (all osteogenesis time points combined; ALLOSTEO). The obtained results indicate that the performance of reference genes depends on the differentiation protocol and on the analysis time, thus providing valuable information for the design of RT-PCR experiments. Copyright © 2016. Published by Elsevier B.V.

Performance of a novel baffled osmotic membrane bioreactor-microfiltration hybrid system under continuous operation for simultaneous nutrient removal and mitigation of brine discharge.

PubMed

Pathak, Nirenkumar; Chekli, Laura; Wang, Jin; Kim, Youngjin; Phuntsho, Sherub; Li, Sheng; Ghaffour, Noreddine; Leiknes, TorOve; Shon, Hokyong

2017-09-01

The present study investigated the performance of an integrated osmotic and microfiltration membrane bioreactor system for wastewater treatment employing baffles in the reactor. Thus, this reactor design enables both aerobic and anoxic processes in an attempt to reduce the process footprint and energy costs associated with continuous aeration. The process performance was evaluated in terms of water flux, salinity build up in the bioreactor, organic and nutrient removal and microbial activity using synthetic reverse osmosis (RO) brine as draw solution (DS). The incorporation of MF membrane was effective in maintaining a reasonable salinity level (612-1434mg/L) in the reactor which resulted in a much lower flux decline (i.e. 11.48-6.98LMH) as compared to previous studies. The stable operation of the osmotic membrane bioreactor-forward osmosis (OMBR-FO) process resulted in an effective removal of both organic matter (97.84%) and nutrient (phosphate 87.36% and total nitrogen 94.28%), respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Role of Carbohydrates at the Origin of Homochirality in Biosystems

NASA Astrophysics Data System (ADS)

Toxvaerd, Søren

2013-10-01

Pasteur has demonstrated that the chiral components in a racemic mixture can separate in homochiral crystals. But with a strong chiral discrimination the chiral components in a concentrated mixture can also phase separate into homochiral fluid domains, and the isomerization kinetics can then perform a symmetry breaking into one thermodynamical stable homochiral system. Glyceraldehyde has a sufficient chiral discrimination to perform such a symmetry breaking. The requirement of a high concentration of the chiral reactant(s) in an aqueous solution in order to perform and maintain homochirality; the appearance of phosphorylation of almost all carbohydrates in the central machinery of life; the basic ideas that the biochemistry and the glycolysis and gluconeogenesis contain the trace of the biochemical evolution, all point in the direction of that homochirality was obtained just after- or at a phosphorylation of the very first products of the formose reaction, at high concentrations of the reactants in phosphate rich compartments in submarine hydrothermal vents. A racemic solution of D,L-glyceraldehyde-3-phosphate could be the template for obtaining homochiral D-glyceraldehyde-3-phosphate(aq) as well as L-amino acids.

Anaerobic treatment of rice winery wastewater in an upflow filter packed with steel slag under different hydraulic loading conditions.

PubMed

Jo, Yeadam; Kim, Jaai; Hwang, Seokhwan; Lee, Changsoo

2015-10-01

Rice-washing drainage (RWD), a strong organic wastewater, was anaerobically treated using an upflow filter filled with blast-furnace slag. The continuous performance of the reactor was examined at varying hydraulic retention times (HRTs). The reactor achieved 91.7% chemical oxygen demand removal (CODr) for a 10-day HRT (0.6 g COD/Ld organic loading rate) and maintained fairly stable performance until the HRT was shortened to 2.2 days (CODr > 84%). Further decreases in HRT caused process deterioration (CODr < 50% and pH < 5.5 for a 0.7-day HRT). The methane production rate increased with decreasing HRT to reach the peak level for a 1.3-day HRT, whereas the yield was significantly greater for 3.4-day or longer HRTs. The substrate removal and methane production kinetics were successfully evaluated, and the generated kinetic models produced good performance predictions. The methanogenic activity of the reactor likely relies on the filter biofilm, with Methanosaeta being the main driver. Copyright © 2015 Elsevier Ltd. All rights reserved.

Akt Suppression of TGFβ Signaling Contributes to the Maintenance of Vascular Identity in Embryonic Stem Cell-Derived Endothelial Cells

PubMed Central

Israely, Edo; Ginsberg, Michael; Nolan, Daniel; Ding, Bi-Sen; James, Daylon; Elemento, Olivier; Rafii, Shahin; Rabbany, Sina Y

2016-01-01

The ability to generate and maintain stable in vitro cultures of mouse endothelial cells (EC) has great potential for genetic dissection of the numerous pathologies involving vascular dysfunction as well as therapeutic applications. However, previous efforts at achieving sustained cultures of primary stable murine vascular cells have fallen short, and the cellular requirements for EC maintenance in vitro remain undefined. In this study, we have generated vascular ECs from mouse embryonic stem (ES) cells, and show that active Akt is essential to their survival and propagation as homogeneous monolayers in vitro. These cells harbor the phenotypical, biochemical, and functional characteristics of ECs, and expand throughout long-term cultures, while maintaining their angiogenic capacity. Moreover, Akt-transduced embryonic ECs form functional perfused vessels in vivo that anastomose with host blood vessels. We provide evidence for a novel function of Akt in stabilizing EC identity, whereby the activated form of the protein protects mouse ES cell-derived ECs from TGFβ-mediated transdifferentiation by downregulating SMAD3. These findings identify a role for Akt in regulating the developmental potential of ES cell-derived ECs, and demonstrate that active Akt maintains endothelial identity in embryonic ECs by interfering with active TGFβ-mediated processes that would ordinarily usher these cells to alternate fates. PMID:23963623

Akt suppression of TGFβ signaling contributes to the maintenance of vascular identity in embryonic stem cell-derived endothelial cells.

PubMed

Israely, Edo; Ginsberg, Michael; Nolan, Daniel; Ding, Bi-Sen; James, Daylon; Elemento, Olivier; Rafii, Shahin; Rabbany, Sina Y

2014-01-01

The ability to generate and maintain stable in vitro cultures of mouse endothelial cells (ECs) has great potential for genetic dissection of the numerous pathologies involving vascular dysfunction as well as therapeutic applications. However, previous efforts at achieving sustained cultures of primary stable murine vascular cells have fallen short, and the cellular requirements for EC maintenance in vitro remain undefined. In this study, we have generated vascular ECs from mouse embryonic stem (ES) cells and show that active Akt is essential to their survival and propagation as homogeneous monolayers in vitro. These cells harbor the phenotypical, biochemical, and functional characteristics of ECs and expand throughout long-term cultures, while maintaining their angiogenic capacity. Moreover, Akt-transduced embryonic ECs form functional perfused vessels in vivo that anastomose with host blood vessels. We provide evidence for a novel function of Akt in stabilizing EC identity, whereby the activated form of the protein protects mouse ES cell-derived ECs from TGFβ-mediated transdifferentiation by downregulating SMAD3. These findings identify a role for Akt in regulating the developmental potential of ES cell-derived ECs and demonstrate that active Akt maintains endothelial identity in embryonic ECs by interfering with active TGFβ-mediated processes that would ordinarily usher these cells to alternate fates. © AlphaMed Press.

Kleptothermy: an additional category of thermoregulation, and a possible example in sea kraits (Laticauda laticaudata, Serpentes)

PubMed Central

Brischoux, François; Bonnet, Xavier; Shine, Richard

2009-01-01

Lacking the capacity for thermogenesis, most ectotherms inhabiting thermally heterogeneous environments rely instead upon exploiting that ambient heterogeneity. In many cases they maintain body temperatures within a narrow range despite massive spatial and temporal variation in ambient conditions. Reliance on diverse thermal opportunities is reflected in specific terms for organisms that bask in sunlight to regulate their temperature (heliotherms), or that press their bodies against warm substrates to facilitate heat flow (thigmotherms), or that rely on large body mass to maintain thermal constancy (gigantothermy). We propose an additional category of thermoregulators: kleptotherms, which regulate their own temperature by ‘stealing’ heat from other organisms. This concept involves two major conditions: the thermal heterogeneity created by the presence of a warm organism in a cool environment and the selective use of that heterogeneity by another animal to maintain body temperatures at higher (and more stable) levels than would be possible elsewhere in the local area. Kleptothermy occurs in endotherms also, but is usually reciprocal (rather than unilateral as in ectotherms). Thermal monitoring on a small tropical island documents a possible example of kleptothermy, based on high stable temperatures of a sea snake (Laticauda laticaudata) inside a burrow occupied by seabirds. PMID:19656862

Six questions about translational due diligence.

PubMed

Selinger, Evan

2010-04-28

To maintain stable respect and support, translational research must be guided by appropriate ethical, social, legal, and political concerns and carry out culturally competent practices. Considering six key questions concerning due diligence will enable the translational research community to examine critically how it approaches these endeavors.

Bechstein's bats maintain individual social links despite a complete reorganisation of their colony structure

NASA Astrophysics Data System (ADS)

Baigger, A.; Perony, N.; Reuter, M.; Leinert, V.; Melber, M.; Grünberger, S.; Fleischmann, D.; Kerth, G.

2013-09-01

Several social mammals, including elephants and some primates, whales and bats, live in multilevel societies that form temporary subgroups. Despite these fission-fusion dynamics, group members often maintain long-term bonds. However, it is unclear whether such individual links and the resulting stable social subunits continue to exist after a complete reorganisation of a society, e.g. following a population crash. Here, we employed a weighted network analysis on 7,109 individual roosting records collected over 4 years in a wild Bechstein's bat colony. We show that, in response to a strong population decline, the colony's two stable social subunits fused into a non-modular social network. Nevertheless, in the first year after the crash, long-term bonds were still detectable, suggesting that the bats remembered previous individual relationships. Our findings are important for understanding the flexibility of animal societies in the face of dramatic changes and for the conservation of social mammals with declining populations.

Bechstein's bats maintain individual social links despite a complete reorganisation of their colony structure.

PubMed

Baigger, A; Perony, N; Reuter, M; Leinert, V; Melber, M; Grünberger, S; Fleischmann, D; Kerth, G

2013-09-01

Several social mammals, including elephants and some primates, whales and bats, live in multilevel societies that form temporary subgroups. Despite these fission-fusion dynamics, group members often maintain long-term bonds. However, it is unclear whether such individual links and the resulting stable social subunits continue to exist after a complete reorganisation of a society, e.g. following a population crash. Here, we employed a weighted network analysis on 7,109 individual roosting records collected over 4 years in a wild Bechstein's bat colony. We show that, in response to a strong population decline, the colony's two stable social subunits fused into a non-modular social network. Nevertheless, in the first year after the crash, long-term bonds were still detectable, suggesting that the bats remembered previous individual relationships. Our findings are important for understanding the flexibility of animal societies in the face of dramatic changes and for the conservation of social mammals with declining populations.

Long-term stable production of monocyte-colony inhibition factor (M-CIF) from CHO microcarrier perfusion cultures.

PubMed

Kong, D; Gentz, R; Zhang, J

1998-03-01

Monocyte-colony inhibition factor (M-CIF) was produced in microcarrier perfusion cultures from engineered Chinese hamster ovary (CHO) cells. Three and fifteen liter microcarrier perfusion bioreactors equipped with internal spin filters were operated for over two months. Approximately 60 L and 300 L of culture filtrate were harvested from the 3L and 15L microcarrier perfusion bioreactors respectively. During the perfusion operation, cell density reached 2-6 × 10(6) cells/ml. Importantly, stable expression of M-CIF from the CHO cells under non-selection condition was maintained at a level of 4-10 mg/L. Specific productivity was maintained at 1.8-3.4 mg/billion cells/day. The ability of the recombinant CHO cells to migrate from microcarrier to microcarrier under our proprietary HGS-CHO-3 medium greatly facilitated microcarrier culture scale-up and microcarrier replenishment. Future directions for microcarrier perfusion system scale-up and process development are highlighted.

Effects of environmental and pharmacological manipulations on a novel delayed nonmatching-to-sample 'working memory' procedure in unrestrained rhesus monkeys.

PubMed

Hutsell, Blake A; Banks, Matthew L

2015-08-15

Working memory is a domain of 'executive function.' Delayed nonmatching-to-sample (DNMTS) procedures are commonly used to examine working memory in both human laboratory and preclinical studies. The aim was to develop an automated DNMTS procedure maintained by food pellets in rhesus monkeys using a touch-sensitive screen attached to the housing chamber. Specifically, the DNMTS procedure was a 2-stimulus, 2-choice recognition memory task employing unidimensional discriminative stimuli and randomized delay interval presentations. DNMTS maintained a delay-dependent decrease in discriminability that was independent of the retention interval distribution. Eliminating reinforcer availability during a single delay session or providing food pellets before the session did not systematically alter accuracy, but did reduce total choices. Increasing the intertrial interval enhanced accuracy at short delays. Acute Δ(9)-THC pretreatment produced delay interval-dependent changes in the forgetting function at doses that did not alter total choices. Acute methylphenidate pretreatment only decreased total choices. All monkeys were trained to perform NMTS at the 1s training delay within 60 days of initiating operant touch training. Furthermore, forgetting functions were reliably delay interval-dependent and stable over the experimental period (∼6 months). Consistent with previous studies, increasing the intertrial interval improved DNMTS performance, whereas Δ(9)-THC disrupted DNMTS performance independent of changes in total choices. Overall, the touchscreen-based DNMTS procedure described provides an efficient method for training and testing experimental manipulations on working memory in unrestrained rhesus monkeys. Copyright © 2015 Elsevier B.V. All rights reserved.

Operator splitting method for simulation of dynamic flows in natural gas pipeline networks

DOE PAGES

Dyachenko, Sergey A.; Zlotnik, Anatoly; Korotkevich, Alexander O.; ...

2017-09-19

Here, we develop an operator splitting method to simulate flows of isothermal compressible natural gas over transmission pipelines. The method solves a system of nonlinear hyperbolic partial differential equations (PDEs) of hydrodynamic type for mass flow and pressure on a metric graph, where turbulent losses of momentum are modeled by phenomenological Darcy-Weisbach friction. Mass flow balance is maintained through the boundary conditions at the network nodes, where natural gas is injected or withdrawn from the system. Gas flow through the network is controlled by compressors boosting pressure at the inlet of the adjoint pipe. Our operator splitting numerical scheme ismore » unconditionally stable and it is second order accurate in space and time. The scheme is explicit, and it is formulated to work with general networks with loops. We test the scheme over range of regimes and network configurations, also comparing its performance with performance of two other state of the art implicit schemes.« less

Modular reflector concept study

NASA Technical Reports Server (NTRS)

Vaughan, D. H.

1981-01-01

A study was conducted to evaluate the feasibility of space erecting a 100 meter paraboloidal radio frequency reflector by joining a number of individually deployed structural modules. Three module design concepts were considered: (1) the deployable cell module (DCM); (2) the modular paraboloidal erectable truss antenna (Mod-PETA); and (3) the modular erectable truss antenna (META). With the space shuttle (STS) as the launch system, the methodology of packaging and stowing in the orbiter, and of dispensing, deploying and joining, in orbit, were studied and the necessary support equipment identified. The structural performance of the completed reflectors was evaluated and their overall operational capability and feasibility were evaluated and compared. The potential of the three concepts to maintain stable shape in the space environment was determined. Their ability to operate at radio frequencies of 1 GHz and higher was assessed assuming the reflector surface to consist of a number of flat, hexagonal facets. A parametric study was performed to determine figure degradation as a function of reflector size, flat facet size, and f/D ratio.

Navigation Strategies for Primitive Solar System Body Rendezvous and Proximity Operations

NASA Technical Reports Server (NTRS)

Getzandanner, Kenneth M.

2011-01-01

A wealth of scientific knowledge regarding the composition and evolution of the solar system can be gained through reconnaissance missions to primitive solar system bodies. This paper presents analysis of a baseline navigation strategy designed to address the unique challenges of primitive body navigation. Linear covariance and Monte Carlo error analysis was performed on a baseline navigation strategy using simulated data from a· design reference mission (DRM). The objective of the DRM is to approach, rendezvous, and maintain a stable orbit about the near-Earth asteroid 4660 Nereus. The outlined navigation strategy and resulting analyses, however, are not necessarily limited to this specific target asteroid as they may he applicable to a diverse range of mission scenarios. The baseline navigation strategy included simulated data from Deep Space Network (DSN) radiometric tracking and optical image processing (OpNav). Results from the linear covariance and Monte Carlo analyses suggest the DRM navigation strategy is sufficient to approach and perform proximity operations in the vicinity of the target asteroid with meter-level accuracy.

A novel teaching system for industrial robots.

PubMed

Lin, Hsien-I; Lin, Yu-Hsiang

2014-03-27

The most important tool for controlling an industrial robotic arm is a teach pendant, which controls the robotic arm movement in work spaces and accomplishes teaching tasks. A good teaching tool should be easy to operate and can complete teaching tasks rapidly and effortlessly. In this study, a new teaching system is proposed for enabling users to operate robotic arms and accomplish teaching tasks easily. The proposed teaching system consists of the teach pen, optical markers on the pen, a motion capture system, and the pen tip estimation algorithm. With the marker positions captured by the motion capture system, the pose of the teach pen is accurately calculated by the pen tip algorithm and used to control the robot tool frame. In addition, Fitts' Law is adopted to verify the usefulness of this new system, and the results show that the system provides high accuracy, excellent operation performance, and a stable error rate. In addition, the system maintains superior performance, even when users work on platforms with different inclination angles.

A Novel Teaching System for Industrial Robots

PubMed Central

Lin, Hsien-I; Lin, Yu-Hsiang

2014-01-01

The most important tool for controlling an industrial robotic arm is a teach pendant, which controls the robotic arm movement in work spaces and accomplishes teaching tasks. A good teaching tool should be easy to operate and can complete teaching tasks rapidly and effortlessly. In this study, a new teaching system is proposed for enabling users to operate robotic arms and accomplish teaching tasks easily. The proposed teaching system consists of the teach pen, optical markers on the pen, a motion capture system, and the pen tip estimation algorithm. With the marker positions captured by the motion capture system, the pose of the teach pen is accurately calculated by the pen tip algorithm and used to control the robot tool frame. In addition, Fitts' Law is adopted to verify the usefulness of this new system, and the results show that the system provides high accuracy, excellent operation performance, and a stable error rate. In addition, the system maintains superior performance, even when users work on platforms with different inclination angles. PMID:24681669

Upgrade to the Birmingham Irradiation Facility

NASA Astrophysics Data System (ADS)

Dervan, P.; French, R.; Hodgson, P.; Marin-Reyes, H.; Parker, K.; Wilson, J.; Baca, M.

2015-10-01

The Birmingham Irradiation Facility was developed in 2013 at the University of Birmingham using the Medical Physics MC40 cyclotron. It can achieve High Luminosity LHC (HL-LHC) fluences of 1015 (1 MeV neutron equivalent (neq)) cm-2 in 80 s with proton beam currents of 1 μA and so can evaluate effectively the performance and durability of detector technologies and new components to be used for the HL-LHC. Irradiations of silicon sensors and passive materials can be carried out in a temperature controlled cold box which moves continuously through the homogenous beamspot. This movement is provided by a pre-configured XY-axis Cartesian robot scanning system. In 2014 the cooling system and cold box were upgraded from a recirculating glycol chiller system to a liquid nitrogen evaporative system. The new cooling system achieves a stable temperature of -50 °C in 30 min and aims to maintain sub-0 °C temperatures on the sensors during irradiations. This paper reviews the design, development, commissioning and performance of the new cooling system.

Performance of anaerobic fluidized membrane bioreactors using effluents of microbial fuel cells treating domestic wastewater.

PubMed

Kim, Kyoung-Yeol; Yang, Wulin; Ye, Yaoli; LaBarge, Nicole; Logan, Bruce E

2016-05-01

Anaerobic fluidized membrane bioreactors (AFMBRs) have been mainly developed as a post-treatment process to produce high quality effluent with very low energy consumption. The performance of an AFMBR was examined using the effluent from a microbial fuel cell (MFC) treating domestic wastewater, as a function of AFMBR hydraulic retention times (HRTs) and organic matter loading rates. The MFC-AFMBR achieved 89 ± 3% removal of the chemical oxygen demand (COD), with an effluent of 36 ± 6 mg-COD/L over 112 days operation. The AFMBR had very stable operation, with no significant changes in COD removal efficiencies, for HRTs ranging from 1.2 to 3.8h, although the effluent COD concentration increased with organic loading. Transmembrane pressure (TMP) was low, and could be maintained below 0.12 bar through solids removal. This study proved that the AFMBR could be operated with a short HRT but a low COD loading rate was required to achieve low effluent COD. Copyright © 2016 Elsevier Ltd. All rights reserved.

A recirculation aerosol wind tunnel for evaluating aerosol samplers and measuring particle penetration through protective clothing materials.

PubMed

Jaques, Peter A; Hsiao, Ta-Chih; Gao, Pengfei

2011-08-01

A recirculation aerosol wind tunnel was designed to maintain a uniform airflow and stable aerosol size distribution for evaluating aerosol sampler performance and determining particle penetration through protective clothing materials. The oval-shaped wind tunnel was designed to be small enough to fit onto a lab bench, have optimized dimensions for uniformity in wind speed and particle size distributions, sufficient mixing for even distribution of particles, and minimum particle losses. Performance evaluation demonstrates a relatively high level of spatial uniformity, with a coefficient of variation of 1.5-6.2% for wind velocities between 0.4 and 2.8 m s(-1) and, in this range, 0.8-8.5% for particles between 50 and 450 nm. Aerosol concentration stabilized within the first 5-20 min with, approximately, a count median diameter of 135 nm and geometric standard deviation of 2.20. Negligible agglomerate growth and particle loss are suggested. The recirculation design appears to result in unique features as needed for our research.

Propfan test assessment propfan propulsion system static test report

NASA Technical Reports Server (NTRS)

Orourke, D. M.

1987-01-01

The propfan test assessment (PTA) propulsion system successfully completed over 50 hours of extensive static ground tests, including a 36 hour endurance test. All major systems performed as expected, verifying that the large-scale 2.74 m diameter propfan, engine, gearbox, controls, subsystems, and flight instrumentation will be satisfactory with minor modifications for the upcoming PTA flight tests on the GII aircraft in early 1987. A test envelope was established for static ground operation to maintain propfan blade stresses within limits for propfan rotational speeds up to 105 percent and power levels up to 3880 kW. Transient tests verified stable, predictable response of engine power and propfan speed controls. Installed engine TSFC was better than expected, probably due to the excellent inlet performance coupled with the supercharging effect of the propfan. Near- and far-field noise spectra contained three dominant components, which were dependent on power, tip speed, and direction. The components were propfan blade tones, propfan random noise, and compressor/propfan interaction noise. No significant turbine noise or combustion noise was evident.

Applying Dynamical Systems Theory to Optimize Libration Point Orbit Stationkeeping Maneuvers for WIND

NASA Technical Reports Server (NTRS)

Brown, Jonathan M.; Petersen, Jeremy D.

2014-01-01

NASA's WIND mission has been operating in a large amplitude Lissajous orbit in the vicinity of the interior libration point of the Sun-Earth/Moon system since 2004. Regular stationkeeping maneuvers are required to maintain the orbit due to the instability around the collinear libration points. Historically these stationkeeping maneuvers have been performed by applying an incremental change in velocity, or (delta)v along the spacecraft-Sun vector as projected into the ecliptic plane. Previous studies have shown that the magnitude of libration point stationkeeping maneuvers can be minimized by applying the (delta)v in the direction of the local stable manifold found using dynamical systems theory. This paper presents the analysis of this new maneuver strategy which shows that the magnitude of stationkeeping maneuvers can be decreased by 5 to 25 percent, depending on the location in the orbit where the maneuver is performed. The implementation of the optimized maneuver method into operations is discussed and results are presented for the first two optimized stationkeeping maneuvers executed by WIND.

Anaerobic co-digestion of high-strength organic wastes pretreated by thermal hydrolysis.

PubMed

Choi, Gyucheol; Kim, Jaai; Lee, Seungyong; Lee, Changsoo

2018-06-01

Thermal hydrolysis (TH) pretreatment was investigated for the anaerobic digestion (AD) of a mixture of high-strength organic wastes (i.e., dewatered human feces, dewatered sewage sludge, and food wastewater) at laboratory scale to simulate a full-scale plant and evaluate its feasibility. The reactors maintained efficient and stable performance at a hydraulic retention time of 20 days, which may be not sufficient for the mesophilic AD of high-suspended-solid wastes, despite the temporal variations in organic load. The addition of FeCl 3 was effective in controlling H 2 S and resulted in significant changes in the microbial community structure, particularly the methanogens. The temporary interruption in feeding or temperature control led to immediate performance deterioration, but it recovered rapidly when normal operations were resumed. The overall results suggest that the AD process coupled with TH pretreatment can provide an efficient, robust, and resilient system to manage high-suspended-solid wastes, supporting the feasibility of its full-scale implementation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Control of robotic assistance using poststroke residual voluntary effort.

PubMed

Makowski, Nathaniel S; Knutson, Jayme S; Chae, John; Crago, Patrick E

2015-03-01

Poststroke hemiparesis limits the ability to reach, in part due to involuntary muscle co-activation (synergies). Robotic approaches are being developed for both therapeutic benefit and continuous assistance during activities of daily living. Robotic assistance may enable participants to exert less effort, thereby reducing expression of the abnormal co-activation patterns, which could allow participants to reach further. This study evaluated how well participants could perform a reaching task with robotic assistance that was either provided independent of effort in the vertical direction or in the sagittal plane in proportion to voluntary effort estimated from electromyograms (EMG) on the affected side. Participants who could not reach targets without assistance were enabled to reach further with assistance. Constant anti-gravity force assistance that was independent of voluntary effort did not reduce the quality of reach and enabled participants to exert less effort while maintaining different target locations. Force assistance that was proportional to voluntary effort on the affected side enabled participants to exert less effort and could be controlled to successfully reach targets, but participants had increased difficulty maintaining a stable position. These results suggest that residual effort on the affected side can produce an effective command signal for poststroke assistive devices.

Single-mode laser studies: Design and performance of a fixed-wave length source and coupling of lasers to thin-film optical waveguides

NASA Technical Reports Server (NTRS)

Ladany, I.; Hammer, J. M.

1980-01-01

A module developed for the generation of a stable single wavelength to be used for a fiber optic multiplexing scheme is described. The laser is driven with RZ pulses, and the temperature is stabilized thermoelectrically. The unit is capable of maintaining a fixed wavelength within about 6 A as the pulse duty cycle is changed between 0 and 100 percent. This is considered the most severe case, and much tighter tolerances are obtainable for constant input power coding schemes. Using a constricted double heterostructure laser, a wavelength shift of 0.083 A mA is obtained due to laser self-heating by a dc driving current. The thermoelectric unit is capable of maintaining a constant laser heat-sink temperature within 0.02 C. In addition, miniature lenses and couplers are described which allow efficient coupling of single wavelength modes of junction lasers to thin film optical waveguides. The design of the miniature cylinder lenses and the prism coupling techniques allow 2 mW of single wavelength mode junction laser light to b coupled into thin film waveguides using compact assemblies. Selective grating couplers are also studied.

Clinical, biochemical, and hygiene assessment of stabled horses provided continuous or intermittent access to drinking water.

PubMed

Freeman, D A; Cymbaluk, N F; Schott, H C; Hinchcliff, K; McDonnell, S M; Kyle, B

1999-11-01

To compare health, hydration status, and management of stabled pregnant mares provided drinking water continuously or via 1 of 3 intermittent delivery systems. 22 Quarter Horse (QH) or QH-crossbred mares and 18 Belgian or Belgian-crossbred mares (study 1); 24 QH or QH-crossbred mares and 18 Belgian or Belgian-crossbred mares (study 2). Stabled horses were provided water continuously or via 1 of 3 intermittent water delivery systems in 2 study periods during a 2-year period. Body temperature, attitude, appetite, water intake, and urine output were recorded daily. Hygiene of each horse and the stable were assessed weekly. Clinical and biochemical measures of hydration were determined 3 times during each study. Clinical measures of hydration included skin turgor, gum moisture, capillary refill time, and fecal consistency. Biochemical measures of hydration included PCV, plasma total protein concentration, serum osmolality, plasma vasopressin concentration, urine specific gravity, and urine osmolality. All horses remained healthy. Stable hygiene was worse when horses had continuous access to water. Clinical and biochemical measures of hydration did not differ among water delivery systems. Various continuous and intermittent water delivery systems provided adequate amounts of water to stabled horses to maintain health and hydration status. Providing intermittent access to water may be preferable on the basis of stable hygiene.

School Food Gardens: Fertile Ground for Education

ERIC Educational Resources Information Center

Beery, Moira; Adatia, Rachel; Segantin, Orsola; Skaer, Chantal-Fleur

2014-01-01

Purpose: The purpose of this paper is to respond to food insecurity and environmental sustainability through school food gardens in Johannesburg, South Africa. Design/Methodology/Approach: Permaculture is a method of organic agriculture where the garden design maintains a stable and productive ecosystem, mimicking natural processes and thereby…

Neurosurgical Management of Spina Bifida: Research Issues

ERIC Educational Resources Information Center

Bowman, Robin M.; McLone, David G.

2010-01-01

The neurosurgical goal when treating children with spina bifida (predominantly myelomeningocele) is to maintain stable neurological functioning throughout the patient's life time. Unfortunately, few long-term outcome studies are available to help direct the neurosurgical care of a child born with myelomeningocele and often treatment relies more…

Natural selection on thermal performance in a novel thermal environment

PubMed Central

Logan, Michael L.; Cox, Robert M.; Calsbeek, Ryan

2014-01-01

Tropical ectotherms are thought to be especially vulnerable to climate change because they are adapted to relatively stable temperature regimes, such that even small increases in environmental temperature may lead to large decreases in physiological performance. One way in which tropical organisms may mitigate the detrimental effects of warming is through evolutionary change in thermal physiology. The speed and magnitude of this response depend, in part, on the strength of climate-driven selection. However, many ectotherms use behavioral adjustments to maintain preferred body temperatures in the face of environmental variation. These behaviors may shelter individuals from natural selection, preventing evolutionary adaptation to changing conditions. Here, we mimic the effects of climate change by experimentally transplanting a population of Anolis sagrei lizards to a novel thermal environment. Transplanted lizards experienced warmer and more thermally variable conditions, which resulted in strong directional selection on thermal performance traits. These same traits were not under selection in a reference population studied in a less thermally stressful environment. Our results indicate that climate change can exert strong natural selection on tropical ectotherms, despite their ability to thermoregulate behaviorally. To the extent that thermal performance traits are heritable, populations may be capable of rapid adaptation to anthropogenic warming. PMID:25225361

Natural selection on thermal performance in a novel thermal environment.

PubMed

Logan, Michael L; Cox, Robert M; Calsbeek, Ryan

2014-09-30

Tropical ectotherms are thought to be especially vulnerable to climate change because they are adapted to relatively stable temperature regimes, such that even small increases in environmental temperature may lead to large decreases in physiological performance. One way in which tropical organisms may mitigate the detrimental effects of warming is through evolutionary change in thermal physiology. The speed and magnitude of this response depend, in part, on the strength of climate-driven selection. However, many ectotherms use behavioral adjustments to maintain preferred body temperatures in the face of environmental variation. These behaviors may shelter individuals from natural selection, preventing evolutionary adaptation to changing conditions. Here, we mimic the effects of climate change by experimentally transplanting a population of Anolis sagrei lizards to a novel thermal environment. Transplanted lizards experienced warmer and more thermally variable conditions, which resulted in strong directional selection on thermal performance traits. These same traits were not under selection in a reference population studied in a less thermally stressful environment. Our results indicate that climate change can exert strong natural selection on tropical ectotherms, despite their ability to thermoregulate behaviorally. To the extent that thermal performance traits are heritable, populations may be capable of rapid adaptation to anthropogenic warming.

Neuron-Inspired Fe3O4/Conductive Carbon Filament Network for High-Speed and Stable Lithium Storage.

PubMed

Hao, Shu-Meng; Li, Qian-Jie; Qu, Jin; An, Fei; Zhang, Yu-Jiao; Yu, Zhong-Zhen

2018-05-17

Construction of a continuous conductance network with high electron-transfer rate is extremely important for high-performance energy storage. Owing to the highly efficient mass transport and information transmission, neurons are exactly a perfect model for electron transport, inspiring us to design a neuron-like reaction network for high-performance lithium-ion batteries (LIBs) with Fe 3 O 4 as an example. The reactive cores (Fe 3 O 4 ) are protected by carbon shells and linked by carbon filaments, constituting an integrated conductance network. Thus, once the reaction starts, the electrons released from every Fe 3 O 4 cores are capable of being transferred rapidly through the whole network directly to the external circuit, endowing the nanocomposite with tremendous rate performance and ultralong cycle life. After 1000 cycles at current densities as high as 1 and 2 A g -1 , charge capacities of the as-synthesized nanocomposite maintain 971 and 715 mA h g -1 , respectively, much higher than those of reported Fe 3 O 4 -based anode materials. The Fe 3 O 4 -based conductive network provides a new idea for future developments of high-rate-performance LIBs.

Effect of Si in reactively sputtered Ti-Si-N films on structure and diffusion barrier performance

NASA Astrophysics Data System (ADS)

Sun, X.; Kolawa, E.; Im, S.; Garland, C.; Nicolet, M.-A.

Two ternary films about 100 nm thick, Ti34Si23N43 (b3) and Ti35Si13N52 (c3), are synthesized by reactively sputtering a Ti5Si3 or a Ti3Si target, respectively. The silicon-lean film (c3) has a columnar structure closely resembling that of TiN. As a diffusion barrier between a shallow Si n+p junction diode and a Cu overlayer, this material is effective up to 700 °C for 30 min annealing in vacuum, a performance similar to that for TiN. The silicon-rich (b3) film contains nanocrystals of TiN, randomly oriented and embedded in an amorphous matrix. A film of (b3) maintains the stability of the same diode structure up to 850 °C for 30 min in vacuum. This film (b3) is clearly superior to TiN or to (c3). Similar experiments performed with Al instead of Cu overlayers highlight the importance of the thermodynamic stability of a barrier layer and demonstrate convincingly that for stable barriers the microstructure is a parameter that directly determines the barrier performance.

Coupling the Alkaline-Surfactant-Polymer Technology and The Gelation Technology to Maximize Oil Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malcolm Pitts; Jie Qi; Dan Wilson

2005-10-01

Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or more efficient areal sweep efficiency for those with high permeability contrast ''thief zones''. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more oil than waterflooding from swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or those with thief zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. A priormore » fluid-fluid report discussed interaction of different gel chemical compositions and alkaline-surfactant-polymer solutions. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses. Aluminum-polyacrylamide, flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9. Chromium acetate-polyacrylamide flowing and rigid flowing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid flowing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid flowing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid flowing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. None of the gels tested appeared to alter alkaline-surfactant-polymer solution oil recovery. Total waterflood plus chemical flood oil recovery sequence recoveries were all similar. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetate gels that were stable to injection of alkaline-surfactant-polymer solutions at 72 F were stable to injection of alkaline-surfactant-polymer solutions at 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Xanthan gum-chromium acetate gels maintained gel integrity in linear corefloods after injection of an alkaline-surfactant-polymer solution at 125 F. At 175 F, Xanthan gum-chromium acetate gels were not stable either with or without subsequent alkaline-surfactant-polymer solution injection. Numerical simulation demonstrated that reducing the permeability of a high permeability zone of a reservoir with gel improved both waterflood and alkaline-surfactant-polymer flood oil recovery. A Minnelusa reservoir with both A and B sand production was simulated. A and B sands are separated by a shale layer. A sand and B sand waterflood oil recovery was improved by 196,000 bbls when a gel was placed in the B sand. A sand and B sand alkaline-surfactant-polymer flood oil recovery was improved by 596,000 bbls when a gel was placed in the B sand. Alkaline-surfactant-polymer flood oil recovery improvement over a waterflood was 392,000 bbls. Placing a gel into the B sand prior to an alkaline-surfactant-polymer flood resulted in 989,000 bbl more oil than only water injection.« less

Upstream capacity upgrade in TDM-PON using RSOA based tunable fiber ring laser.

PubMed

Yi, Lilin; Li, Zhengxuan; Dong, Yi; Xiao, Shilin; Chen, Jian; Hu, Weisheng

2012-04-23

An upstream multi-wavelength shared (UMWS) time division multiplexing passive optical network (TDM-PON) is presented by using a reflective semiconductor amplifier (RSOA) and tunable optical filter (TOF) based directly modulated fiber ring laser as upstream laser source. The stable laser operation is easily achieved no matter what the bandwidth and shape of the TOF is and it can be directly modulated when the RSOA is driven at its saturation region. In this UMWS TDM-PON system, an individual wavelength can be assigned to the user who has a high bandwidth demand by tuning the central wavelength of the TOF in its upgraded optical network unit (ONU), while others maintain their traditional ONU structure and share the bandwidth via time slots, which greatly and dynamically upgrades the upstream capacity. We experimentally demonstrated the bidirectional transmission of downstream data at 10-Gb/s and upstream data at 1.25-Gb/s per wavelength over 25-km single mode fiber (SMF) with almost no power penalty at both ends. A stable performance is observed for the upstream wavelength tuned from 1530 nm to 1595 nm. Moreover, due to the high extinction ratio (ER) of the upstream signal, the burst-mode transmitting is successfully presented and a better time-division multiplexing performance can be obtained by turning off the unused lasers thanks to the rapid formation of the laser in the fiber ring. © 2012 Optical Society of America

Toward a stable solid-electrolyte-interfaces on nickel-rich cathodes: LiPO2F2 salt-type additive and its working mechanism for LiNi0.5Mn0.25Co0.25O2 cathodes

NASA Astrophysics Data System (ADS)

Zhao, Weimin; Zheng, Guorui; Lin, Min; Zhao, Wengao; Li, Dongjiang; Guan, Xiaoyun; Ji, Yajuan; Ortiz, Gregorio F.; Yang, Yong

2018-03-01

Although the LiNi0.5Mn0.25Co0.25O2 holds the merits of high theoretical capacities and a relatively high operating voltage, the battery performance suffers from the severe cycling decay due to the unstable solid electrolyte interface on the cathode. Herein, we present LiPO2F2 as a salt-type electrolyte additive to enhance the cycling stability of large-size crystallite LiNi0.5Mn0.25Co0.25O2 cathodes. Results demonstrate that 1 wt% LiPO2F2 can significantly improve not only the initial coulombic efficiency by 3%, but also the cycling stability and rate capability at 25 °C. Furthermore, the discharge capacity of LiNi0.5Mn0.25Co0.25O2 cathodes still maintain 156 mAh g-1 after 100 cycles even when the temperature increases to 55 °C. In-depth experimental characterization and theoretical calculation indicate that a new stable and thin (e.g. 15-20 nm) film formed on the surface of the cathodes, with composition of LiPO2F2, LiF, etc., which significantly reduces charge transfer impedance of the electrodes, and therefore significantly improves the cycling and rate performance of LiNi0.5Mn0.25Co0.25O2.

Novel flight instrument display to minimize the risk of spatial disorientation

NASA Astrophysics Data System (ADS)

Braithwaite, Malcolm G.; Durnford, Simon J.

1997-06-01

This novel flight instrument display presents information to the pilot in a simple and easily comprehensible format by integrating the five orientational flight parameters. It allows the pilot to select specific orientation parameters and then follow a simple tracking task which ensures that these parameters are maintained or, if necessary, recovered. The pilot can at any time check any parameter he wishes, but is free from the requirement to continually sample and combine information from the traditional instruments to maintain stable flight. Cognitive workload to maintain orientation is thus reduced. Our assessment of the display in a UH-60 helicopter simulator showed that the novel display makes recovery from unusual aircraft attitudes and instrument flying easier than when using the standard instrument panel.

A bi-stable nanoelectromechanical non-volatile memory based on van der Waals force

NASA Astrophysics Data System (ADS)

Soon, Bo Woon; Jiaqiang Ng, Eldwin; Qian, You; Singh, Navab; Julius Tsai, Minglin; Lee, Chengkuo

2013-07-01

By using complementary-metal-oxide-semiconductor processes, a silicon based bi-stable nanoelectromechanical non-volatile memory is fabricated and characterized. The main feature of this device is an 80 nm wide and 3 μm high silicon nanofin (SiNF) of a high aspect ratio (1:35). The switching mechanism is realized by electrostatic actuation between two lateral electrodes, i.e., terminals. Bi-stable hysteresis behavior is demonstrated when the SiNF maintains its contact to one of the two terminals by leveraging on van der Waals force even after voltage bias is turned off. The compelling results indicate that this design is promising for realization of high density non-volatile memory application due to its nano-scale footprint and zero on-hold power consumption.

The effects of drafting on stroking variations during swimming in elite male triathletes.

PubMed

Chollet, D; Hue, O; Auclair, F; Millet, G; Chatard, J C

2000-08-01

The aim of this study was to determine the effects of drafting behind another swimmer on the metabolic response and stroke characteristics. Six highly trained male triathletes performed two maximal 400-m swims, one in a drafting (D) and one in a non-drafting condition (ND). Their metabolic response was assessed by measuring the oxygen uptake (VO2) and the blood lactate concentration at the end of each 400 m. Swimming velocity, stroke frequency, stroke length, and stroke index (velocity multiplied by stroke length) were recorded every 50 m. In the D and ND conditions, there was no difference in VO2 [66.7 (1.7) ml x kg(-1) x min(-1) vs 65.6 (1.2) ml x kg(-1) min(-1) respectively], however, the lactate concentrations were lower in D than in ND [9.6 (0.9) mM vs 10.8 (0.9) mM, respectively, P < 0.01]. In D, the performance [1.39 (0.02) m x s(-1) vs 1.34 (0.02) m x s(-1), respectively, P < 0.01] and the stroking parameters (i.e., stroke length and stroke index) increased significantly, while the stroke frequency remain unchanged. In D, a stable pace was maintained, while in ND, velocity decreased significantly throughout the 400 m. In D, the performance gains were related to the 400-m D velocity (r = 0.78, P < 0.05), and to the body fat mass (BFM, r = 0.99, P < 0.01). The stroke index in D was also related to BFM (r = 0.78, P < 0.05). Faster and leaner swimmers achieved greater performance gains and stroke index when drafting. Thus, drafting during swimming increases the performance and contributes to the maintenance of stable stroking parameters such as stroke frequency and stroke length during a 400-m swim.

Protected Natural Areas of Puerto Rico

Treesearch

William A. Gould; Maya Quinones; Mariano Solorzano; Waldemar Alcobas; Caryl Alarcon

2011-01-01

Protection of natural areas is essential to conserving biodiversity and maintaining ecosystem services. Benefits and services provided by natural areas are complex, interwoven, life-sustaining, and necessary for a healthy environment and a sustainable future (Daily et al. 1997). They include clean water and air, sustainable wildlife populations and habitats, stable...

Financing Facilities 101

ERIC Educational Resources Information Center

Sawyer, Thomas H.

2006-01-01

Successful sport entities have a variety of stable revenue sources to meet increasing expenses. There are three major categories of revenue sources: public, private, and a combination of public and private sources. It is extremely important for the sport manager to ensure that all varieties of revenue streams are maintained. The public sources of…

Ethnolinguistic Identification and Adaptation of Repatriates in Polycultural Kazakhstan

ERIC Educational Resources Information Center

Bokayev, Baurzhan; Zharkynbekova, Sholpan; Nurseitova, Khalida; Bokayeva, Ainash; Akzhigitova, Assel; Nurgalieva, Saniya

2012-01-01

The issues of social, cultural, and language adjustment and the integration of repatriates into the Kazakhstani society are crucial factors in maintaining a stable society. The complicated process of self-identification of ethnic Kazakhs is a major aspect of their sociolinguistic "penetration" into Kazakh society. In this work we…

The Future of Marriage and Family in Black America.

ERIC Educational Resources Information Center

Dickson, Lynda

1993-01-01

Explores reasons for the apparent difficulty that African-American males and females have in establishing and maintaining stable relationships. Data from the National Survey of Black Americans and other sources indicate numerous explanations for the situation, including economic factors. Trends for the future of African-American relationships and…

78 FR 2696 - Submission for OMB Review; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-14

... Securities and Exchange Commission (the ``Commission'') has submitted to the Office of Management and Budget... money market funds. Money market funds are open-end management investment companies that differ from other open-end management investment companies in that they seek to maintain a stable price per share...

Moving And Working On Space Structures

NASA Technical Reports Server (NTRS)

Mclaughlin, Pat B.

1992-01-01

Clawlike device attaches boots to rails. Memorandum presents, in sketches and brief text, concept for boot-toe clip helping astronaut move about outside on structures being built at Space Station. Clip also helps astronaut maintain stable position at worksite. Concept adaptable to underwater work on such structures as offshore oil rigs.

Quick, easy to prepare freeze-dried soups

NASA Technical Reports Server (NTRS)

Ramirez, R. V.; Larson, R. W.

1972-01-01

Major advantages of soups are that they totally rehydrate in less than five minutes in water at approximately 150 deg F, maintain flavor and quality stability for two weeks in a 100 F environment, and remain stable for considerably longer at ambient temperatures. They are suitable for either household or field use.

Steady-state inductive spheromak operation

DOEpatents

Janos, Alan C.; Jardin, Stephen C.; Yamada, Masaaki

1987-01-01

The inductively formed spheromak plasma can be maintained in a highly stable and controlled fashion. Steady-state operation is obtained by forming the plasma in the linked mode, then oscillating the poloidal and toroidal fields such that they have different phases. Preferably, the poloidal and magnetic fields are 90.degree. out of phase.

Stable Polyurethane Coatings for Electronic Circuits

NASA Technical Reports Server (NTRS)

Morris, D. E.

1983-01-01

Alkane-based polyurethanes resist deterioration while maintaining good dielectric properties. Weight loss after prolonged immersion in hot water far less for alkane-based polyurethanes than for more common ether based polyurethanes, at any given oxygen content. Major uses of polyurethanes are as connector potting materials and conformal coatings for printed circuit boards.

19 CFR 143.6 - Failure to maintain performance standards.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Failure to maintain performance standards. 143.6... maintain performance standards. ABI participants must adhere to the performance requirements and... maximum of 90 days, if the participant's performance remains below standard, but, except for immediate...

[Perioperative management of a child with central diabetes insipidus who underwent two surgeries before and after desmopressin administration].

PubMed

Kiriyama, Keiji; Tachibana, Kazuya; Nishimura, Nobuyuki; Takeuchi, Muneyuki; Kinouchi, Keiko

2013-03-01

A 14-year-old girl weighing 32 kg was diagnosed with suprasellar tumor causing hydrocephalus, hypothyroidism, adrenal dysfunction and central diabetes insipidus. She was treated with levothyroxine and hydrocortisone and urged to take fluid to replace urine. She was scheduled to undergo ventricular drainage to relieve hydrocephalus prior to tumor resection. For the first surgery, desmopressin was not started and urine output reached 4,000 to 6,000 ml x day(-1), urine osmolality 64 mOsm x l(-1) and urine specific gravity 1.002. Anesthesia was induced with sevoflurane and maintained with propofol and remifentanil. Maintenance fluid was with acetated Ringer's solution and urine loss was replaced with 5% dextrose. Bradycardia and hypotension occurred after intubation, which was treated with volume load. Infusion volume was 750 ml and urine output was 1100 ml during 133 min of anesthesia. Postoperative day 1 nasal desmopressin was started. Ten days later, partial tumor resection was performed. Anesthesia was induced with propofol and fentanyl and maintained with sevoflurane and remifentanil. Infusion volume was 610 ml, urine output 380 ml, and blood loss 151 ml during 344 min of anesthesia. Hemodynamic parameters were stable throughout the procedure. Pathology of the tumor was revealed to be germinoma. Bradycardia and hypotension experienced during the first surgery was suspected to be caused by preoperative hypovolemia brought by polyuria. Desmopressin was proved to be effective to treat excessive urine output and to maintain good perioperative water balance.

Performance assessment of a single-layer moisture store-and-release cover system at a mine waste rock pile in a seasonally humid region (Nova Scotia, Canada).

PubMed

Power, Christopher; Ramasamy, Murugan; Mkandawire, Martin

2018-03-03

Cover systems are commonly applied to mine waste rock piles (WRPs) to control acid mine drainage (AMD). Single-layer covers utilize the moisture "store-and-release" concept to first store and then release moisture back to the atmosphere via evapotranspiration. Although more commonly used in semi-arid and arid climates, store-and-release covers remain an attractive option in humid climates due to the low cost and relative simplicity of installation. However, knowledge of their performance in these climates is limited. The objective of this study was to assess the performance of moisture store-and-release covers at full-scale WRPs located in humid climates. This cover type was installed at a WRP in Nova Scotia, Canada, alongside state-of-the-art monitoring instrumentation. Field monitoring was conducted over 5 years to assess key components such as meteorological conditions, cover material water dynamics, net percolation, surface runoff, pore-gas, environmental receptor water quality, landform stability and vegetation. Water balances indicate small reductions in water influx to the waste rock (i.e., 34 to 28% of precipitation) with the diminished AMD release also apparent by small improvements in groundwater quality (increase in pH, decrease in sulfate/metals). Surface water quality analysis and field observations of vegetative/aquatic life demonstrate significant improvements in the surface water receptor. The WRP landform is stable and the vegetative cover is thriving. This study has shown that while a simple store-and-release cover may not be a highly effective barrier to water infiltration in humid climates, it can be used to (i) eliminate contaminated surface water runoff, (ii) minimize AMD impacts to surface water receptor(s), (iii) maintain a stable landform, and (iv) provide a sustainable vegetative canopy.

Influence of management of variables, sampling zones and land units on LR analysis for landslide spatial prevision

NASA Astrophysics Data System (ADS)

Greco, R.; Sorriso-Valvo, M.

2013-09-01

Several authors, according to different methodological approaches, have employed logistic Regression (LR), a multivariate statistical analysis adopted to assess the spatial probability of landslide, even though its fundamental principles have remained unaltered. This study aims at assessing the influence of some of these methodological approaches on the performance of LR, through a series of sensitivity analyses developed over a test area of about 300 km2 in Calabria (southern Italy). In particular, four types of sampling (1 - the whole study area; 2 - transects running parallel to the general slope direction of the study area with a total surface of about 1/3 of the whole study area; 3 - buffers surrounding the phenomena with a 1/1 ratio between the stable and the unstable area; 4 - buffers surrounding the phenomena with a 1/2 ratio between the stable and the unstable area), two variable coding modes (1 - grouped variables; 2 - binary variables), and two types of elementary land (1 - cells units; 2 - slope units) units have been tested. The obtained results must be considered as statistically relevant in all cases (Aroc values > 70%), thus confirming the soundness of the LR analysis which maintains high predictive capacities notwithstanding the features of input data. As for the area under investigation, the best performing methodological choices are the following: (i) transects produced the best results (0 < P(y) ≤ 93.4%; Aroc = 79.5%); (ii) as for sampling modalities, binary variables (0 < P(y) ≤ 98.3%; Aroc = 80.7%) provide better performance than ordinated variables; (iii) as for the choice of elementary land units, slope units (0 < P(y) ≤ 100%; Aroc = 84.2%) have obtained better results than cells matrix.

Output Feedback Adaptive Control of Non-Minimum Phase Systems Using Optimal Control Modification

NASA Technical Reports Server (NTRS)

Nguyen, Nhan; Hashemi, Kelley E.; Yucelen, Tansel; Arabi, Ehsan

2018-01-01

This paper describes output feedback adaptive control approaches for non-minimum phase SISO systems with relative degree 1 and non-strictly positive real (SPR) MIMO systems with uniform relative degree 1 using the optimal control modification method. It is well-known that the standard model-reference adaptive control (MRAC) cannot be used to control non-SPR plants to track an ideal SPR reference model. Due to the ideal property of asymptotic tracking, MRAC attempts an unstable pole-zero cancellation which results in unbounded signals for non-minimum phase SISO systems. The optimal control modification can be used to prevent the unstable pole-zero cancellation which results in a stable adaptation of non-minimum phase SISO systems. However, the tracking performance using this approach could suffer if the unstable zero is located far away from the imaginary axis. The tracking performance can be recovered by using an observer-based output feedback adaptive control approach which uses a Luenberger observer design to estimate the state information of the plant. Instead of explicitly specifying an ideal SPR reference model, the reference model is established from the linear quadratic optimal control to account for the non-minimum phase behavior of the plant. With this non-minimum phase reference model, the observer-based output feedback adaptive control can maintain stability as well as tracking performance. However, in the presence of the mismatch between the SPR reference model and the non-minimum phase plant, the standard MRAC results in unbounded signals, whereas a stable adaptation can be achieved with the optimal control modification. An application of output feedback adaptive control for a flexible wing aircraft illustrates the approaches.

Neuroimaging markers associated with maintenance of optimal memory performance in late-life.

PubMed

Dekhtyar, Maria; Papp, Kathryn V; Buckley, Rachel; Jacobs, Heidi I L; Schultz, Aaron P; Johnson, Keith A; Sperling, Reisa A; Rentz, Dorene M

2017-06-01

Age-related memory decline has been well-documented; however, some individuals reach their 8th-10th decade while maintaining strong memory performance. To determine which demographic and biomarker factors differentiated top memory performers (aged 75+, top 20% for memory) from their peers and whether top memory performance was maintained over 3 years. Clinically normal adults (n=125, CDR=0; age: 79.5±3.57 years) from the Harvard Aging Brain Study underwent cognitive testing and neuroimaging (amyloid PET, MRI) at baseline and 3-year follow-up. Participants were grouped into Optimal (n=25) vs. Typical (n=100) performers using performance on 3 challenging memory measures. Non-parametric tests were used to compare groups. There were no differences in age, sex, or education between Optimal vs. Typical performers. The Optimal group performed better in Processing Speed (p=0.016) and Executive Functioning (p<0.001). Optimal performers had larger hippocampal volumes at baseline compared with Typical Performers (p=0.027) but no differences in amyloid burden (p=0.442). Twenty-three of the 25 Optimal performers had longitudinal data and16 maintained top memory performance while 7 declined. Non-Maintainers additionally declined in Executive Functioning but not Processing Speed. Longitudinally, there were no hippocampal volume differences between Maintainers and Non-Maintainers, however Non-Maintainers exhibited higher amyloid burden at baseline in contrast with Maintainers (p=0.008). Excellent memory performance in late life does not guarantee protection against cognitive decline. Those who maintain an optimal memory into the 8th and 9th decades may have lower levels of AD pathology. Copyright © 2017. Published by Elsevier Ltd.

Ploidally antagonistic selection maintains stable genetic polymorphism.

PubMed

Immler, Simone; Arnqvist, Göran; Otto, Sarah Perin

2012-01-01

Understanding the maintenance of genetic variation in the face of selection remains a key issue in evolutionary biology. One potential mechanism for the maintenance of genetic variation is opposing selection during the diploid and haploid stages of biphasic life cycles universal among eukaryotic sexual organisms. If haploid and diploid gene expression both occur, selection can act in each phase, potentially in opposing directions. In addition, sex-specific selection during haploid phases is likely simply because male and female gametophytes/gametes tend to have contrasting life histories. We explored the potential for the maintenance of a stable polymorphism under ploidally antagonistic as well as sex-specific selection. Furthermore, we examined the role of the chromosomal location of alleles (autosomal or sex-linked). Our analyses show that the most permissible conditions for the maintenance of polymorphism occur under negative ploidy-by-sex interactions, where stronger selection for an allele in female than male diploids is coupled with weaker selection against the allele in female than male haploids. Such ploidy-by-sex interactions also promote allele frequency differences between the sexes. With constant fitness, ploidally antagonistic selection can maintain stable polymorphisms for autosomal and X-linked genes but not for Y-linked genes. We discuss the implications of our results and outline a number of biological settings where the scenarios modeled may apply. © 2011 The Author(s). Evolution © 2011 The Society for the Study of Evolution.

Evolutionary stability of mutualism: interspecific population regulation as an evolutionarily stable strategy.

PubMed

Holland, J Nathaniel; DeAngelis, Donald L; Schultz, Stewart T

2004-09-07

Interspecific mutualisms are often vulnerable to instability because low benefit : cost ratios can rapidly lead to extinction or to the conversion of mutualism to parasite-host or predator-prey interactions. We hypothesize that the evolutionary stability of mutualism can depend on how benefits and costs to one mutualist vary with the population density of its partner, and that stability can be maintained if a mutualist can influence demographic rates and regulate the population density of its partner. We test this hypothesis in a model of mutualism with key features of senita cactus (Pachycereus schottii)-senita moth (Upiga virescens) interactions, in which benefits of pollination and costs of larval seed consumption to plant fitness depend on pollinator density. We show that plants can maximize their fitness by allocating resources to the production of excess flowers at the expense of fruit. Fruit abortion resulting from excess flower production reduces pre-adult survival of the pollinating seed-consumer, and maintains its density beneath a threshold that would destabilize the mutualism. Such a strategy of excess flower production and fruit abortion is convergent and evolutionarily stable against invasion by cheater plants that produce few flowers and abort few to no fruit. This novel mechanism of achieving evolutionarily stable mutualism, namely interspecific population regulation, is qualitatively different from other mechanisms invoking partner choice or selective rewards, and may be a general process that helps to preserve mutualistic interactions in nature.

Design and synthesis of a novel multifunctional stabilizer for highly stable uc(dl)-tetrahydropalmatine nanosuspensions and in vitro study

NASA Astrophysics Data System (ADS)

Yan, Beibei; Wang, Yancai; Wang, Lulu; Zhou, Yuqi; Shang, Xueyun; Zhao, Juan; Liu, Yangyang; Du, Juan

2018-05-01

The present study aimed to prepare stable uc(dl)-tetrahydropalmatine (uc(dl)-THP) nanosuspensions of optimized formulation with PEGylated chitosan as a multifunctional stabilizer using the antisolvent precipitation method. A central composite design project of three factors and five-level full factorial (53) was applied to design the experimental program, and response surface methodology analysis was used to optimize the experimental conditions. The effects of critical influencing factors such as PEGylated chitosan concentration, operational temperature, and ultrasonic energy on particle size and zeta potential were investigated. Under the optimization nanosuspension formulation, the particle size was 269 nm and zeta potential was at 37.4 mV. Also, the uc(dl)-THP nanosuspensions maintained good physical stability after 2 months, indicating the potential ability of the multifunctional stabilizer for stable nanosuspension formulation. Hence, the present findings indicated that PEGylated chitosan could be used as the ideal stabilizer to form a physically stable nanosuspension formulation.

``Schooling'' of wing pairs in flapping flight

NASA Astrophysics Data System (ADS)

Ramananarivo, Sophie; Zhang, Jun; Ristroph, Leif; AML, Courant Collaboration; Physics NYU Collaboration

2015-11-01

The experimental setup implements two independent flapping wings swimming in tandem. Both are driven with the same prescribed vertical heaving motion, but the horizontal motion is free, which means that the swimmers can take up any relative position and forward speed. Experiments show however clearly coordinated motions, where the pair of wings `crystallize' into specific stable arrangements. The follower wing locks into the path of the leader, adopting its speed, and with a separation distance that takes on one of several discrete values. By systematically varying the kinematics and wing size, we show that the set of stable spacings is dictated by the wavelength of the periodic wake structure. The forces maintaining the pair cohesion are characterized by applying an external force to the follower to perturb it away from the `stable wells'. These results show that hydrodynamics alone is sufficient to induce cohesive and coordinated collective locomotion through a fluid, and we discuss the hypothesis that fish schools and bird flocks also represent stable modes of motion.

Golf Ball

NASA Technical Reports Server (NTRS)

1998-01-01

The Ultra 500 Series golf balls, introduced in 1995 by Wilson Sporting Goods Company, has 500 dimples arranged in a pattern of 60 spherical triangles. The design employs NASA's aerodynamics technology analysis of air loads of the tank and Shuttle orbiter that was performed under the Space Shuttle External Tank program. According to Wilson, this technology provides 'the most symmetrical ball surface available, sustaining initial velocity longer and producing the most stable ball flight for unmatched accuracy and distance.' The dimples are in three sizes, shapes and depths mathematically positioned for the best effect. The selection of dimples and their placement optimizes the interaction of opposing forces of lift and drag. Large dimples reduce air drag, enhance lift, and maintain spin for distance. Small dimples prevent excessive lift that destabilizes the ball flight and the medium size dimples blend the other two.

A miniature electronically tunable Fabry-Perot filter

NASA Astrophysics Data System (ADS)

O'Sullivan, B.; Pietraszewski, K. A. R.

A miniature electronically tunable, servo controlled Fabry-Perot filter for use in fiber optic sensors, spectroscopy, data and telecommunications, and laser tuning has been developed. The servo control system utilizes capacitance micrometry and piezo technology to maintain stable cavity mirror separations with a noise of less than 0.9nm rms while enabling random access tuning to any wavelength in the design range in less than 0.5ms. Free spectral ranges from 75,000GHz to 300GHz (560nm to 1.5nm at 1500nm wavelength) are typical with finesses between 3 and 300. At present the device has been made commercially available in two formats: fiber optically coupled, with single-mode or multimode fiber, or with a 3mm clear aperture. The design and performance of the instrument are presented along with some typical application examples.

Benefit from NASA

NASA Image and Video Library

1998-01-01

The Ultra 500 Series golf balls, introduced in 1995 by Wilson Sporting Goods Company, has 500 dimples arranged in a pattern of 60 spherical triangles. The design employs NASA's aerodynamics technology analysis of air loads of the tank and Shuttle orbiter that was performed under the Space Shuttle External Tank program. According to Wilson, this technology provides "the most symmetrical ball surface available, sustaining initial velocity longer and producing the most stable ball flight for unmatched accuracy and distance." The dimples are in three sizes, shapes and depths mathematically positioned for the best effect. The selection of dimples and their placement optimizes the interaction of opposing forces of lift and drag. Large dimples reduce air drag, enhance lift, and maintain spin for distance. Small dimples prevent excessive lift that destabilizes the ball flight and the medium size dimples blend the other two.

[Advanced Development for Space Robotics With Emphasis on Fault Tolerance Technology

NASA Technical Reports Server (NTRS)

Tesar, Delbert

1997-01-01

This report describes work developing fault tolerant redundant robotic architectures and adaptive control strategies for robotic manipulator systems which can dynamically accommodate drastic robot manipulator mechanism, sensor or control failures and maintain stable end-point trajectory control with minimum disturbance. Kinematic designs of redundant, modular, reconfigurable arms for fault tolerance were pursued at a fundamental level. The approach developed robotic testbeds to evaluate disturbance responses of fault tolerant concepts in robotic mechanisms and controllers. The development was implemented in various fault tolerant mechanism testbeds including duality in the joint servo motor modules, parallel and serial structural architectures, and dual arms. All have real-time adaptive controller technologies to react to mechanism or controller disturbances (failures) to perform real-time reconfiguration to continue the task operations. The developments fall into three main areas: hardware, software, and theoretical.

Gravitational wave content and stability of uniformly, rotating, triaxial neutron stars in general relativity.

PubMed

Tsokaros, Antonios; Ruiz, Milton; Paschalidis, Vasileios; Shapiro, Stuart L; Baiotti, Luca; Uryū, Kōji

2017-06-15

Targets for ground-based gravitational wave interferometers include continuous, quasiperiodic sources of gravitational radiation, such as isolated, spinning neutron stars. In this work, we perform evolution simulations of uniformly rotating, triaxially deformed stars, the compressible analogs in general relativity of incompressible, Newtonian Jacobi ellipsoids. We investigate their stability and gravitational wave emission. We employ five models, both normal and supramassive, and track their evolution with different grid setups and resolutions, as well as with two different evolution codes. We find that all models are dynamically stable and produce a strain that is approximately one-tenth the average value of a merging binary system. We track their secular evolution and find that all our stars evolve toward axisymmetry, maintaining their uniform rotation, rotational kinetic energy, and angular momentum profiles while losing their triaxiality.

Shadow Areas Robust Matching Among Image Sequence in Planetary Landing

NASA Astrophysics Data System (ADS)

Ruoyan, Wei; Xiaogang, Ruan; Naigong, Yu; Xiaoqing, Zhu; Jia, Lin

2017-01-01

In this paper, an approach for robust matching shadow areas in autonomous visual navigation and planetary landing is proposed. The approach begins with detecting shadow areas, which are extracted by Maximally Stable Extremal Regions (MSER). Then, an affine normalization algorithm is applied to normalize the areas. Thirdly, a descriptor called Multiple Angles-SIFT (MA-SIFT) that coming from SIFT is proposed, the descriptor can extract more features of an area. Finally, for eliminating the influence of outliers, a method of improved RANSAC based on Skinner Operation Condition is proposed to extract inliers. At last, series of experiments are conducted to test the performance of the approach this paper proposed, the results show that the approach can maintain the matching accuracy at a high level even the differences among the images are obvious with no attitude measurements supplied.

Relationship between accuracy and complexity when learning underarm precision throwing.

PubMed

Valle, Maria Stella; Lombardo, Luciano; Cioni, Matteo; Casabona, Antonino

2018-06-12

Learning precision ball throwing was mostly studied to explore the early rapid improvement of accuracy, with poor attention on possible adaptive processes occurring later when the rate of improvement is reduced. Here, we tried to demonstrate that the strategy to select angle, speed and height at ball release can be managed during the learning periods following the performance stabilization. To this aim, we used a multivariate linear model with angle, speed and height as predictors of changes in accuracy. Participants performed underarm throws of a tennis ball to hit a target on the floor, 3.42 m away. Two training sessions (S1, S2) and one retention test were executed. Performance accuracy increased over the S1 and stabilized during the S2, with a rate of changes along the throwing axis slower than along the orthogonal axis. However, both the axes contributed to the performance changes over the learning and consolidation time. A stable relationship between the accuracy and the release parameters was observed only during S2, with a good fraction of the performance variance explained by the combination of speed and height. All the variations were maintained during the retention test. Overall, accuracy improvements and reduction in throwing complexity at the ball release followed separate timing over the course of learning and consolidation.

Hierarchical cobalt poly-phosphide hollow spheres as highly active and stable electrocatalysts for hydrogen evolution over a wide pH range

NASA Astrophysics Data System (ADS)

Wu, Tianli; Pi, Mingyu; Wang, Xiaodeng; Guo, Weimeng; Zhang, Dingke; Chen, Shijian

2018-01-01

Exploring highly-efficient and low-cost non-noble metal electrocatalyst toward the hydrogen evolution reaction (HER) is highly desired for renewable energy system but remains challenging. In this work, three dimensional hierarchical porous cobalt poly-phosphide hollow spheres (CoP3 HSs) were prepared by topotactic phosphidation of the cobalt-based precursor via vacuum encapsulation technique. As a porous HER cathode, the CoP3 HSs delivers remarkable electrocatalytic performance over the wide pH range. It needs overpotentials of -69 mV and -118 mV with a small Tafel slope of 51 mV dec-1 to obtain current densities of 10 mA cm-2 and 50 mA cm-2, respectively, and maintains its electrocatalytic performance over 30 h in acidic solution. In addition, CoP3 also exhibit superior electrocatalytic performance and stability under neutral and alkaline conditions for the HER. Both experimental measurements and density functional theory (DFT) calculations are performed to explore the mechanism behind the excellent HER performance. The results of our study make the porous CoP3 HSs as a promising electrocatalyst for practical applications toward energy conversion system and present a new way for designing and fabricating HER electrodes through high degree of phosphorization and nano-porous architecture.

A comparison of dehydroepiandrosterone and 7-keto dehydroepiandrosterone with other drugs that modulate ethanol intake in rats responding under a multiple schedule

PubMed Central

Amato, Russell J.; Hulin, Mary W.; Winsauer, Peter J.

2012-01-01

Dehydroepiandrosterone (DHEA), 7-keto DHEA, and several comparison drugs (ethanol, chlordiazepoxide, rauwolscine, and RO15-4513) were administered to male rats responding under a multiple schedule of food and ethanol presentation to determine their selectively for decreasing ethanol-maintained responding. DHEA and 7-keto DHEA significantly decreased both ethanol- and food-maintained responding, compared to control, while also decreasing blood ethanol concentration (BEC). Acute ethanol administration also decreased responding for both food and ethanol; however, ethanol-maintained responding was more potently decreased than food-maintained responding. BEC remained relatively stable after increasing ethanol doses. Among the other drugs tested, RO15-4513 was the most selective for decreasing ethanol-maintained responding compared to food-maintained responding, and it decreased BECs as ethanol-maintained responding decreased. The largest dose of rauwolscine significantly decreased responding for food, while not affecting ethanol-maintained responding compared to control. Low to intermediate doses of rauwolscine produced small, non-significant increases in ethanol-maintained responding and BECs. Chlordiazepoxide produced significant decreases in food-maintained responding and the dose of ethanol presented, but only at the highest dose tested. Although DHEA and 7-keto DHEA did not decrease ethanol-maintained responding as selectively as ethanol or RO15-4513 under the multiple schedule, these neurosteroids may be valuable pharmacological tools in the development of new treatments for alcohol abuse and dependence. PMID:22473025

Pharmacogenetics-based warfarin dosing algorithm decreases time to stable anticoagulation and the risk of major hemorrhage: an updated meta-analysis of randomized controlled trials.

PubMed

Wang, Zhi-Quan; Zhang, Rui; Zhang, Peng-Pai; Liu, Xiao-Hong; Sun, Jian; Wang, Jun; Feng, Xiang-Fei; Lu, Qiu-Fen; Li, Yi-Gang

2015-04-01

Warfarin is yet the most widely used oral anticoagulant for thromboembolic diseases, despite the recently emerged novel anticoagulants. However, difficulty in maintaining stable dose within the therapeutic range and subsequent serious adverse effects markedly limited its use in clinical practice. Pharmacogenetics-based warfarin dosing algorithm is a recently emerged strategy to predict the initial and maintaining dose of warfarin. However, whether this algorithm is superior over conventional clinically guided dosing algorithm remains controversial. We made a comparison of pharmacogenetics-based versus clinically guided dosing algorithm by an updated meta-analysis. We searched OVID MEDLINE, EMBASE, and the Cochrane Library for relevant citations. The primary outcome was the percentage of time in therapeutic range. The secondary outcomes were time to stable therapeutic dose and the risks of adverse events including all-cause mortality, thromboembolic events, total bleedings, and major bleedings. Eleven randomized controlled trials with 2639 participants were included. Our pooled estimates indicated that pharmacogenetics-based dosing algorithm did not improve percentage of time in therapeutic range [weighted mean difference, 4.26; 95% confidence interval (CI), -0.50 to 9.01; P = 0.08], but it significantly shortened the time to stable therapeutic dose (weighted mean difference, -8.67; 95% CI, -11.86 to -5.49; P < 0.00001). Additionally, pharmacogenetics-based algorithm significantly reduced the risk of major bleedings (odds ratio, 0.48; 95% CI, 0.23 to 0.98; P = 0.04), but it did not reduce the risks of all-cause mortality, total bleedings, or thromboembolic events. Our results suggest that pharmacogenetics-based warfarin dosing algorithm significantly improves the efficiency of International Normalized Ratio correction and reduces the risk of major hemorrhage.

Epigenetic reprogramming in plant sexual reproduction.

PubMed

Kawashima, Tomokazu; Berger, Frédéric

2014-09-01

Epigenetic reprogramming consists of global changes in DNA methylation and histone modifications. In mammals, epigenetic reprogramming is primarily associated with sexual reproduction and occurs during both gametogenesis and early embryonic development. Such reprogramming is crucial not only to maintain genomic integrity through silencing transposable elements but also to reset the silenced status of imprinted genes. In plants, observations of stable transgenerational inheritance of epialleles have argued against reprogramming. However, emerging evidence supports that epigenetic reprogramming indeed occurs during sexual reproduction in plants and that it has a major role in maintaining genome integrity and a potential contribution to epiallelic variation.

Targeting Stable Rotors to Treat Atrial Fibrillation.

PubMed

Narayan, Sanjiv M; Krummen, David E

2012-09-01

Therapy for atrial fibrillation (AF) remains suboptimal, in large part because its mechanisms are unclear. While pulmonary vein ectopy may trigger AF, it remains uncertain how AF, once triggered, is actually sustained. Recent discoveries show that human AF is maintained by a small number of rotors or focal sources. AF sources are widely distributed in patient-specific locations, often remote from pulmonary veins and in the right atrium and stable for prolonged periods of time. In a multicentre experience, brief targeted ablation at sources (focal impulse and rotor modulation [FIRM]) terminated AF predominantly to sinus rhythm prior to pulmonary vein isolation and eliminated AF on rigorous followup. This review summarises the evidence for stable rotors and focal sources of human AF and their clinical role as ablation targets to eliminate paroxysmal, persistent and long-standing persistent AF.

Methanosarcinaceae and Acetate-Oxidizing Pathways Dominate in High-Rate Thermophilic Anaerobic Digestion of Waste-Activated Sludge

PubMed Central

Ho, Dang P.; Jensen, Paul D.

2013-01-01

This study investigated the process of high-rate, high-temperature methanogenesis to enable very-high-volume loading during anaerobic digestion of waste-activated sludge. Reducing the hydraulic retention time (HRT) from 15 to 20 days in mesophilic digestion down to 3 days was achievable at a thermophilic temperature (55°C) with stable digester performance and methanogenic activity. A volatile solids (VS) destruction efficiency of 33 to 35% was achieved on waste-activated sludge, comparable to that obtained via mesophilic processes with low organic acid levels (<200 mg/liter chemical oxygen demand [COD]). Methane yield (VS basis) was 150 to 180 liters of CH4/kg of VSadded. According to 16S rRNA pyrotag sequencing and fluorescence in situ hybridization (FISH), the methanogenic community was dominated by members of the Methanosarcinaceae, which have a high level of metabolic capability, including acetoclastic and hydrogenotrophic methanogenesis. Loss of function at an HRT of 2 days was accompanied by a loss of the methanogens, according to pyrotag sequencing. The two acetate conversion pathways, namely, acetoclastic methanogenesis and syntrophic acetate oxidation, were quantified by stable carbon isotope ratio mass spectrometry. The results showed that the majority of methane was generated by nonacetoclastic pathways, both in the reactors and in off-line batch tests, confirming that syntrophic acetate oxidation is a key pathway at elevated temperatures. The proportion of methane due to acetate cleavage increased later in the batch, and it is likely that stable oxidation in the continuous reactor was maintained by application of the consistently low retention time. PMID:23956388

Long-Term Stability of Tramadol and Ketamine Solutions for Patient-Controlled Analgesia Delivery.

PubMed

Gu, Junfeng; Qin, Wengang; Chen, Fuchao; Xia, Zhongyuan

2015-08-26

Subanesthetic doses of ketamine as an adjuvant to tramadol in patient-controlled analgesia (PCA) for postoperative pain have been shown to improve the quality of analgesia. However, there are no such commercially available drug mixtures, and the stability of the combination has rarely been assessed. Admixtures were assessed for periods of up to 14 days at 4°C and 25°C. Three different mixtures of tramadol and ketamine (tramadol 5.0 mg/mL + ketamine 0.5 mg/mL, tramadol 5.0 mg/mL + ketamine 1.0 mg/mL, and tramadol 5.0 mg/mL + ketamine 2.0 mg/mL) were prepared in polyolefin bags by combining these 2 drugs with 0.9% sodium chloride (normal saline [NS]). The chemical stability of the admixtures was evaluated by a validated high-performance liquid chromatography (HPLC) method and by measurement of pH values. Solution appearance and color were assessed by observing the samples against black and white backgrounds. Solutions were considered stable if they maintained 90% of the initial concentration of each drug. The percentages of initial concentration of tramadol and ketamine in the various solutions remained above 98% when stored at 4°C or 25°C over the testing period. No changes in color or turbidity were observed in any of the prepared solutions. Throughout this period, pH values remained stable. The results indicate that the drug mixtures of tramadol with ketamine in NS for PCA delivery systems were stable for 14 days when stored in polyolefin bags at 4°C or 25°C.

Force production during squats performed with a rotational resistance device under stable versus unstable conditions.

PubMed

Moras, Gerard; Vázquez-Guerrero, Jairo

2015-11-01

[Purpose] Force production during a squat action on a rotational resistance device (RRD) under stable and unstable conditions. [Subjects and Methods] Twenty-one healthy males were asked to perform six sets of six repetitions of squats on an RRD on either stable or unstable surfaces. The stable and unstable sets were performed on different days. Muscular outputs were obtained from a linear encoder and a strain gauge fixed to a vest. [Results] Overall, the results showed no significant differences for any of the dependent variables across exercise modes. Forcemean outputs were higher in the concentric phase than in the eccentric phase for each condition, but there were no differences in velocity, time or displacement. The forcepeak was similar in the eccentric and concentric phases of movement under both stable and unstable conditions. There were no significant differences in forcemean between sets per condition or between conditions. [Conclusion] These results suggest that performing squats with a RRD achieves similar forcemean and forcepeak under stable and unstable conditions. The forcepeak produced is also similar in concentric and eccentric phases.

Force production during squats performed with a rotational resistance device under stable versus unstable conditions

PubMed Central

Moras, Gerard; Vázquez-Guerrero, Jairo

2015-01-01

[Purpose] Force production during a squat action on a rotational resistance device (RRD) under stable and unstable conditions. [Subjects and Methods] Twenty-one healthy males were asked to perform six sets of six repetitions of squats on an RRD on either stable or unstable surfaces. The stable and unstable sets were performed on different days. Muscular outputs were obtained from a linear encoder and a strain gauge fixed to a vest. [Results] Overall, the results showed no significant differences for any of the dependent variables across exercise modes. Forcemean outputs were higher in the concentric phase than in the eccentric phase for each condition, but there were no differences in velocity, time or displacement. The forcepeak was similar in the eccentric and concentric phases of movement under both stable and unstable conditions. There were no significant differences in forcemean between sets per condition or between conditions. [Conclusion] These results suggest that performing squats with a RRD achieves similar forcemean and forcepeak under stable and unstable conditions. The forcepeak produced is also similar in concentric and eccentric phases. PMID:26696707

Conformation and Stability of Intramolecular Telomeric G-Quadruplexes: Sequence Effects in the Loops

PubMed Central

Sattin, Giovanna; Artese, Anna; Nadai, Matteo; Costa, Giosuè; Parrotta, Lucia; Alcaro, Stefano; Palumbo, Manlio; Richter, Sara N.

2013-01-01

Telomeres are guanine-rich sequences that protect the ends of chromosomes. These regions can fold into G-quadruplex structures and their stabilization by G-quadruplex ligands has been employed as an anticancer strategy. Genetic analysis in human telomeres revealed extensive allelic variation restricted to loop bases, indicating that the variant telomeric sequences maintain the ability to fold into G-quadruplex. To assess the effect of mutations in loop bases on G-quadruplex folding and stability, we performed a comprehensive analysis of mutant telomeric sequences by spectroscopic techniques, molecular dynamics simulations and gel electrophoresis. We found that when the first position in the loop was mutated from T to C or A the resulting structure adopted a less stable antiparallel topology; when the second position was mutated to C or A, lower thermal stability and no evident conformational change were observed; in contrast, substitution of the third position from A to C induced a more stable and original hybrid conformation, while mutation to T did not significantly affect G-quadruplex topology and stability. Our results indicate that allelic variations generate G-quadruplex telomeric structures with variable conformation and stability. This aspect needs to be taken into account when designing new potential anticancer molecules. PMID:24367632

Surface transformation by a “cocktail” solvent enables stable cathode materials for sodium ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mu, Linqin; Rahman, Muhammad Mominur; Zhang, Yan

Coating the surfaces of active materials has become an effective and indispensable path towards the stable operation of practical rechargeable batteries. Improving the affordability of coating processes can bring enormous manufacturing advantages to battery applications. Here in this paper, we report a cheap, simple and efficient method to create conformal coating layers on the primary particles of sodium layered oxide materials for improving battery performance. Mimicking the cathode–electrolyte interfacial reaction in practical cells, we create conformal coating layers via the spontaneous reaction between the oxidative cathode surfaces and a cocktail of reductive organic solvents. The conformal coating layers consist ofmore » metal–organic compounds with reduced transition metal cations, i.e., artificial cathode–electrolyte interphases (CEIs). The cells containing these coated cathode materials deliver much improved cycle life while maintaining reasonably high reversible capacity and rate capability. Furthermore, the structural stability and water resistance are enhanced, which can practically help simplify the storage protocol of cathode powders prior to battery manufacturing. The surfaces of most oxide cathode materials (e.g., lithium cathodes and sodium cathodes) are highly oxidative, and thus we expect that the present method, with tailored experimental parameters, can be readily applied to most battery systems.« less

Study of plasma-based stable and ultra-wideband electromagnetic wave absorption for stealth application

NASA Astrophysics Data System (ADS)

Xuyang, CHEN; Fangfang, SHEN; Yanming, LIU; Wei, AI; Xiaoping, LI

2018-06-01

A plasma-based stable, ultra-wideband electromagnetic (EM) wave absorber structure is studied in this paper for stealth applications. The stability is maintained by a multi-layer structure with several plasma layers and dielectric layers distributed alternately. The plasma in each plasma layer is designed to be uniform, whereas it has a discrete nonuniform distribution from the overall view of the structure. The nonuniform distribution of the plasma is the key to obtaining ultra-wideband wave absorption. A discrete Epstein distribution model is put forward to constrain the nonuniform electron density of the plasma layers, by which the wave absorption range is extended to the ultra-wideband. Then, the scattering matrix method (SMM) is employed to analyze the electromagnetic reflection and absorption of the absorber structure. In the simulation, the validation of the proposed structure and model in ultra-wideband EM wave absorption is first illustrated by comparing the nonuniform plasma model with the uniform case. Then, the influence of various parameters on the EM wave reflection of the plasma are simulated and analyzed in detail, verifying the EM wave absorption performance of the absorber. The proposed structure and model are expected to be superior in some realistic applications, such as supersonic aircraft.

Planned Pregnancy in a Chronic Myeloid Leukemia Patient in Molecular Remission

PubMed Central

Pavlovsky, Carolina; Giere, Isabel; Van Thillo, Germán

2012-01-01

Excellent response rates and a good quality of life have been observed since the introduction of tyrosine kinase inhibitors (TKIs) in chronic myeloid leukemia (CML) treatment. Consequently, some challenges began to appear in CML women in child-bearing age wishing to become pregnant. Currently, many women around the world are in stable major/complete molecular response MMR/CMR (MMR: <0.1% BCR-ABL/ABL and CMR: undetectable BCR-ABL mRNA by RQ-PCR transcript levels on the international scale). The condition of stable MMR/CMR is linked to a long-term virtual absence of progression to the accelerated and blastic phase and to the possibility of stopping the TKI treatment with the maintenance of a condition of CMR in a proportion of cases. Imatinib teratogenic and prescribing information prohibits the use of it during pregnancy. We describe the case of a 36-year-old female patient with CML in chronic phase who stopped imatinib after 2 years in major molecular response (MMR) to plan a pregnancy. Molecular monitoring by RQ-PCR was performed quarterly. She achieved a safe pregnancy and delivery maintaining an optimal molecular response throughout the pregnancy. Isolated literature reports have been described, but no formal advice has been described at present time. PMID:22928126

State diagram of a three-sphere microswimmer in a channel

NASA Astrophysics Data System (ADS)

Daddi-Moussa-Ider, Abdallah; Lisicki, Maciej; Mathijssen, Arnold J. T. M.; Hoell, Christian; Goh, Segun; Bławzdziewicz, Jerzy; Menzel, Andreas M.; Löwen, Hartmut

2018-06-01

Geometric confinements are frequently encountered in soft matter systems and in particular significantly alter the dynamics of swimming microorganisms in viscous media. Surface-related effects on the motility of microswimmers can lead to important consequences in a large number of biological systems, such as biofilm formation, bacterial adhesion and microbial activity. On the basis of low-Reynolds-number hydrodynamics, we explore the state diagram of a three-sphere microswimmer under channel confinement in a slit geometry and fully characterize the swimming behavior and trajectories for neutral swimmers, puller- and pusher-type swimmers. While pushers always end up trapped at the channel walls, neutral swimmers and pullers may further perform a gliding motion and maintain a stable navigation along the channel. We find that the resulting dynamical system exhibits a supercritical pitchfork bifurcation in which swimming in the mid-plane becomes unstable beyond a transition channel height while two new stable limit cycles or fixed points that are symmetrically disposed with respect to the channel mid-height emerge. Additionally, we show that an accurate description of the averaged swimming velocity and rotation rate in a channel can be captured analytically using the method of hydrodynamic images, provided that the swimmer size is much smaller than the channel height.

LIBS analysis of artificial calcified tissues matrices.

PubMed

Kasem, M A; Gonzalez, J J; Russo, R E; Harith, M A

2013-04-15

In most laser-based analytical methods, the reproducibility of quantitative measurements strongly depends on maintaining uniform and stable experimental conditions. For LIBS analysis this means that for accurate estimation of elemental concentration, using the calibration curves obtained from reference samples, the plasma parameters have to be kept as constant as possible. In addition, calcified tissues such as bone are normally less "tough" in their texture than many samples, especially metals. Thus, the ablation process could change the sample morphological features rapidly, and result in poor reproducibility statistics. In the present work, three artificial reference sample sets have been fabricated. These samples represent three different calcium based matrices, CaCO3 matrix, bone ash matrix and Ca hydroxyapatite matrix. A comparative study of UV (266 nm) and IR (1064 nm) LIBS for these three sets of samples has been performed under similar experimental conditions for the two systems (laser energy, spot size, repetition rate, irradiance, etc.) to examine the wavelength effect. The analytical results demonstrated that UV-LIBS has improved reproducibility, precision, stable plasma conditions, better linear fitting, and the reduction of matrix effects. Bone ash could be used as a suitable standard reference material for calcified tissue calibration using LIBS with a 266 nm excitation wavelength. Copyright © 2013 Elsevier B.V. All rights reserved.

Experimental technique for studying high-temperature phases in reactive molten metal based systems

NASA Astrophysics Data System (ADS)

Ermoline, A.; Schoenitz, M.; Hoffmann, V. K.; Dreizin, E. L.

2004-12-01

Containerless, microgravity experiments for studying equilibria in molten metal-gas systems have been designed and conducted onboard of a NASA KC-135 aircraft flying parabolic trajectories. An experimental apparatus enabling one to acoustically levitate, laser heat, and splat quench 1-3 mm metal and ceramic samples has been developed and equipped with computer-based controller and optical diagnostics. Normal-gravity testing determined the levitator operation parameters providing stable and adjustable sample positioning. A methodology for optimizing the levitator performance using direct observation of levitated samples was developed and found to be more useful than traditional pressure mapping of the acoustic field. In microgravity experiments, spherical specimens prepared of pressed, premixed powders of ZrO2, ZrN, and Zr, were acoustically levitated inside an argon-filled chamber at one atmosphere and heated by a CO2 laser up to 2800 K. Using a uniaxial acoustic levitator in microgravity, the location of the laser-heated samples could be maintained for about 1 s, so that local sample melting was achieved. Oscillations of the levitating samples in horizontal direction became pronounced in microgravity. These oscillations increased during the sample heating and eventually resulted in moving the sample out of the stable position and away from the laser beam.

Surface transformation by a “cocktail” solvent enables stable cathode materials for sodium ion batteries

DOE PAGES

Mu, Linqin; Rahman, Muhammad Mominur; Zhang, Yan; ...

2018-01-09

Coating the surfaces of active materials has become an effective and indispensable path towards the stable operation of practical rechargeable batteries. Improving the affordability of coating processes can bring enormous manufacturing advantages to battery applications. Here in this paper, we report a cheap, simple and efficient method to create conformal coating layers on the primary particles of sodium layered oxide materials for improving battery performance. Mimicking the cathode–electrolyte interfacial reaction in practical cells, we create conformal coating layers via the spontaneous reaction between the oxidative cathode surfaces and a cocktail of reductive organic solvents. The conformal coating layers consist ofmore » metal–organic compounds with reduced transition metal cations, i.e., artificial cathode–electrolyte interphases (CEIs). The cells containing these coated cathode materials deliver much improved cycle life while maintaining reasonably high reversible capacity and rate capability. Furthermore, the structural stability and water resistance are enhanced, which can practically help simplify the storage protocol of cathode powders prior to battery manufacturing. The surfaces of most oxide cathode materials (e.g., lithium cathodes and sodium cathodes) are highly oxidative, and thus we expect that the present method, with tailored experimental parameters, can be readily applied to most battery systems.« less

Use of reverse osmosis membranes to remove perfluorooctane sulfonate (PFOS) from semiconductor wastewater.

PubMed

Tang, Chuyang Y; Fu, Q Shiang; Robertson, A P; Criddle, Craig S; Leckie, James O

2006-12-01

Perfluorooctane sulfonate (PFOS) and related substances are persistent, bioaccumulative, and toxic, and thus of substantial environmental concern. PFOS is an essential photolithographic chemical in the semiconductor industry with no substitutes yet identified. The industry seeks effective treatment technologies. The feasibility of using reverse osmosis (RO) membranes for treating semiconductor wastewater containing PFOS has been investigated. Commercial RO membranes were characterized in terms of permeability, salt rejection, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and membrane surface zeta potential (streaming potential measurements). Filtration tests were performed to determine the membrane flux and PFOS rejection. Over a wide range of feed concentrations (0.5 - 1500 ppm), the RO membranes generally rejected 99% or more of the PFOS. Rejection was better for tighter membranes, but was not affected by membrane zeta potential. Flux decreased with increasing PFOS concentration. While the flux reduction was severe for a loose RO membrane probably due to its higher initial flux, very stable flux was maintained for tighter membranes. At a very high feed concentration (about 500 ppm), all the membranes exhibited an identical stable flux. Isopropyl alcohol, present in some semiconductor wastewaters, had a detrimental effect on membrane flux. Where present it needs to be removed from the wastewater prior to using RO membranes.

Purification of a Multidrug Resistance Transporter for Crystallization Studies

PubMed Central

Alegre, Kamela O.; Law, Christopher J.

2015-01-01

Crystallization of integral membrane proteins is a challenging field and much effort has been invested in optimizing the overexpression and purification steps needed to obtain milligram amounts of pure, stable, monodisperse protein sample for crystallography studies. Our current work involves the structural and functional characterization of the Escherichia coli multidrug resistance transporter MdtM, a member of the major facilitator superfamily (MFS). Here we present a protocol for isolation of MdtM to increase yields of recombinant protein to the milligram quantities necessary for pursuit of structural studies using X-ray crystallography. Purification of MdtM was enhanced by introduction of an elongated His-tag, followed by identification and subsequent removal of chaperonin contamination. For crystallization trials of MdtM, detergent screening using size exclusion chromatography determined that decylmaltoside (DM) was the shortest-chain detergent that maintained the protein in a stable, monodispersed state. Crystallization trials of MdtM performed using the hanging-drop diffusion method with commercially available crystallization screens yielded 3D protein crystals under several different conditions. We contend that the purification protocol described here may be employed for production of high-quality protein of other multidrug efflux members of the MFS, a ubiquitous, physiologically and clinically important class of membrane transporters. PMID:27025617

Rx for low cash yields.

PubMed

Tobe, Chris

2003-10-01

Certain strategies can offer not-for-profit hospitals potentially greater investment yields while maintaining stability and principal safety. Treasury inflation-indexed securities can offer good returns, low volatility, and inflation protection. "Enhanced cash" strategies offer liquidity and help to preserve capital. Stable value "wrappers" allow hospitals to pursue higher-yielding fixed-income securities without an increase in volatility.

CONCENTRATED ANIMAL FEEDING OPERATIONS AS A SOURCE OF EDCS AND THEIR MANAGEMENT

EPA Science Inventory

In the United States, there is an estimated 376,000 animal feed operations, generating approximately 128 billion pounds of waste each year. A facility is an animal feed operation (AFO) if animals are stabled/confined, or fed/maintained, for 45 days or more within any 12-month per...

Beyond Transcription Factors: The Role of Chromatin Modifying Enzymes in Regulating Transcription Required for Memory

ERIC Educational Resources Information Center

Barrett, Ruth M.; Wood, Marcelo A.

2008-01-01

One of the alluring aspects of examining chromatin modifications in the role of modulating transcription required for long-term memory processes is that these modifications may provide transient and potentially stable epigenetic marks in the service of activating and/or maintaining transcriptional processes. These, in turn, may ultimately…

The Contribution of Community and Family Contexts to African American Young Adults' Romantic Relationship Health: A Prospective Analysis

ERIC Educational Resources Information Center

Kogan, Steven M.; Lei, Man-Kit; Grange, Christina R.; Simons, Ronald L.; Brody, Gene H.; Gibbons, Frederick X.; Chen, Yi-fu

2013-01-01

Accumulating evidence suggests that African American men and women experience unique challenges in developing and maintaining stable, satisfying romantic relationships. Extant studies have linked relationship quality among African American couples to contemporaneous risk factors such as economic hardship and racial discrimination. Little research,…

Stable catalyst layers for hydrogen permeable composite membranes

DOEpatents

Way, J. Douglas; Wolden, Colin A

2014-01-07

The present invention provides a hydrogen separation membrane based on nanoporous, composite metal carbide or metal sulfide coated membranes capable of high flux and permselectivity for hydrogen without platinum group metals. The present invention is capable of being operated over a broad temperature range, including at elevated temperatures, while maintaining hydrogen selectivity.

75 FR 39168 - Special Regulations; Areas of the National Park System

Federal Register 2010, 2011, 2012, 2013, 2014

2010-07-08

... his death in 1972. During the closure, we completed four projects: installation of a new HVAC system... to either bulge or crack. The existing HVAC system installed in 1985 failed to maintain a stable...; Areas of the National Park System AGENCY: National Park Service. ACTION: Final Rule. SUMMARY: The...

Is It Hot in Here? Thermoregulation and Homeostasis through an Exercise Activity

ERIC Educational Resources Information Center

Dean, Lewis G.; Breslin, Angela; Ross, Emma Z.

2014-01-01

Homeostasis, the control of an internal environment to maintain stable, relatively constant conditions, is a key concept in physiology. In endothermic species, including humans ("Homo sapiens"), the control of body temperature is fundamental to the control of a suitable internal environment. To help regulate core body temperature, the…

Nano-sized Superlattice Clusters Created by Oxygen Ordering in Mechanically Alloyed Fe Alloys

NASA Astrophysics Data System (ADS)

Hu, Yong-Jie; Li, Jing; Darling, Kristopher A.; Wang, William Y.; Vanleeuwen, Brian K.; Liu, Xuan L.; Kecskes, Laszlo J.; Dickey, Elizabeth C.; Liu, Zi-Kui

2015-07-01

Creating and maintaining precipitates coherent with the host matrix, under service conditions is one of the most effective approaches for successful development of alloys for high temperature applications; prominent examples include Ni- and Co-based superalloys and Al alloys. While ferritic alloys are among the most important structural engineering alloys in our society, no reliable coherent precipitates stable at high temperatures have been found for these alloys. Here we report discovery of a new, nano-sized superlattice (NSS) phase in ball-milled Fe alloys, which maintains coherency with the BCC matrix up to at least 913 °C. Different from other precipitates in ferritic alloys, this NSS phase is created by oxygen-ordering in the BCC Fe matrix. It is proposed that this phase has a chemistry of Fe3O and a D03 crystal structure and becomes more stable with the addition of Zr. These nano-sized coherent precipitates effectively double the strength of the BCC matrix above that provided by grain size reduction alone. This discovery provides a new opportunity for developing high-strength ferritic alloys for high temperature applications.

Conditions sufficient for the production of oral cocaine or lidocaine self-administration in preference to water.

PubMed

Falk, J L; Siris, A; Lau, C E

1996-03-01

Groups of rats were given a chronic history of drinking cocaine solutions of different concentrations in daily, 3-h schedule induced polydipsia sessions. Animals failed to develop a preference for cocaine solution to concurrently presented water. Schedule-induction conditions were maintained, and the animals were divided into separate groups, drinking either cocaine or lidocaine placed in a highly acceptable vehicle (glucose-saccharin solution). Animals preferred their respective drug solutions to concurrently presented water, and these preferences remained stable after the glucose-saccharin vehicle was gradually faded to water, leaving only cocaine or lidocaine, respectively, in the solution. Thus a stable preference for drug solution to water could be instituted in rats for either cocaine or lidocaine solution (putative reinforcing and nonreinforcing agents, respectively) given an appropriate associative history, with high intakes maintained by schedule-induction. Conditions sufficient for the initiation of an oral preference and high intake for a putatively reinforcing drug cannot be assumed to occur owing to the drug's reinforcing property in the absence of demonstrating the ineffectiveness of an appropriate negative control substance.

1.5  μm polarization-maintaining dual-wavelength single-frequency distributed Bragg reflection fiber laser with 28  GHz stable frequency difference.

PubMed

Hou, Yubin; Zhang, Qian; Qi, Shuxian; Feng, Xian; Wang, Pu

2018-03-15

We demonstrate a polarization-maintaining (PM) dual-wavelength (DW) single-frequency Er-doped distributed Bragg reflection (DBR) fiber laser with 28 GHz stable frequency difference. A homemade PM low-reflectivity superimposed fiber Bragg grating (SFBG) is employed as the output port of the DBR fiber laser. The SFBG has two reflection wavelengths located in the same grating region. The reflectivity of both DWs is around 85%. The achieved linear polarization extinction ratio is more than 20 dB. The DWs of the laser output are located at 1552.2 nm and 1552.43 nm, respectively. The optical signal-to-noise ratio (SNR) is above 60 dB. For each wavelength, only one longitudinal mode exists. The beat frequency of the two longitudinal modes is measured to be 28.4474 GHz, with the SNR of more than 65 dB and the linewidth less than 300 Hz. During a 60-min-long measurement, the standard deviation of the frequency fluctuation is 58.592 kHz.

Advanced Sodium Ion Battery Anode Constructed via Chemical Bonding between Phosphorus, Carbon Nanotube, and Cross-Linked Polymer Binder.

PubMed

Song, Jiangxuan; Yu, Zhaoxin; Gordin, Mikhail L; Li, Xiaolin; Peng, Huisheng; Wang, Donghai

2015-12-22

Maintaining structural stability is a great challenge for high-capacity conversion electrodes with large volume change but is necessary for the development of high-energy-density, long-cycling batteries. Here, we report a stable phosphorus anode for sodium ion batteries by the synergistic use of chemically bonded phosphorus-carbon nanotube (P-CNT) hybrid and cross-linked polymer binder. The P-CNT hybrid was synthesized through ball-milling of red phosphorus and carboxylic group functionalized carbon nanotubes. The P-O-C bonds formed in this process help maintain contact between phosphorus and CNTs, leading to a durable hybrid. In addition, cross-linked carboxymethyl cellulose-citric acid binder was used to form a robust electrode. As a result, this anode delivers a stable cycling capacity of 1586.2 mAh/g after 100 cycles, along with high initial Coulombic efficiency of 84.7% and subsequent cycling efficiency of ∼99%. The unique electrode framework through chemical bonding strategy reported here is potentially inspirable for other electrode materials with large volume change in use.

Maintaining stable radiation pressure acceleration of ion beams via cascaded electron replenishment

NASA Astrophysics Data System (ADS)

Shen, X. F.; Qiao, B.; Chang, H. X.; Zhang, W. L.; Zhang, H.; Zhou, C. T.; He, X. T.

2017-03-01

A method to maintain ion stable radiation pressure acceleration (RPA) from laser-irradiated thin foils is proposed, where a series of high-Z nanofilms are placed behind to successively replenish co-moving electrons into the accelerating foil as electron charging stations (ECSs). Such replenishment of co-moving electrons, on the one hand, helps to keep a dynamic balance between the electrostatic pressure in the accelerating slab and the increasing laser radiation pressure with a Gaussian temporal profile at the rising front, i.e. dynamically matching the optimal condition of RPA; on the other hand, it aids in suppressing the foil Coulomb explosion due to loss of electrons induced by transverse instabilities during RPA. Two-dimensional and three-dimensional particle-in-cell simulations show that a monoenergetic Si14+ beam with a peak energy of 3.7 GeV and particle number 4.8× {10}9 (charge 11 nC) can be obtained at an intensity of 7 × 1021 W cm-2 and the conversion efficiency from laser to high energy ions is improved significantly by using the ECSs in our scheme.

Preparation and Relaxation of Very Stable Glassy States of a Simulated Liquid

NASA Astrophysics Data System (ADS)

Jack, Robert L.; Hedges, Lester O.; Garrahan, Juan P.; Chandler, David

2011-12-01

We prepare metastable glassy states in a model glass former made of Lennard-Jones particles by sampling biased ensembles of trajectories with low dynamical activity. These trajectories form an inactive dynamical phase whose “fast” vibrational degrees of freedom are maintained at thermal equilibrium by contact with a heat bath, while the “slow” structural degrees of freedom are located in deep valleys of the energy landscape. We examine the relaxation to equilibrium and the vibrational properties of these metastable states. The glassy states we prepare by our trajectory sampling method are very stable to thermal fluctuations and also more mechanically rigid than low-temperature equilibrated configurations.

Throat-bypass bleed systems for increasing the stable airflow range of a Mach 2.50 axisymmetric inlet with 40-percent internal contraction

NASA Technical Reports Server (NTRS)

Sanders, B. W.; Mitchell, G. A.

1973-01-01

The results of an experimental investigation to increase the stable airflow range of a super sonic mixed-compression inlet are presented. Various throat-bypass bleeds were located on the inlet cowl. The bleed types were distributed porous normal holes, a forward slanted slot, or distributed educated slots. Large inlet stability margins were obtained with the inlet throat bleed systems if a constant pressure was maintained in the throat-bypass bleed plenum. Stability limits were determined for steady-state and limited transient internal air flow changes. Limited unstart angle-of-attack data are presented.

Air-stable and freestanding lithium alloy/graphene foil as an alternative to lithium metal anodes

NASA Astrophysics Data System (ADS)

Zhao, Jie; Zhou, Guangmin; Yan, Kai; Xie, Jin; Li, Yuzhang; Liao, Lei; Jin, Yang; Liu, Kai; Hsu, Po-Chun; Wang, Jiangyan; Cheng, Hui-Ming; Cui, Yi

2017-10-01

Developing high-capacity anodes is a must to improve the energy density of lithium batteries for electric vehicle applications. Alloy anodes are one promising option, but without pre-stored lithium, the overall energy density is limited by the low-capacity lithium metal oxide cathodes. Recently, lithium metal has been revived as a high-capacity anode, but faces several challenges owing to its high reactivity and uncontrolled dendrite growth. Here, we show a series of Li-containing foils inheriting the desirable properties of alloy anodes and pure metal anodes. They consist of densely packed LixM (M = Si, Sn, or Al) nanoparticles encapsulated by large graphene sheets. With the protection of graphene sheets, the large and freestanding LixM/graphene foils are stable in different air conditions. With fully expanded LixSi confined in the highly conductive and chemically stable graphene matrix, this LixSi/graphene foil maintains a stable structure and cyclability in half cells (400 cycles with 98% capacity retention). This foil is also paired with high-capacity Li-free V2O5 and sulfur cathodes to achieve stable full-cell cycling.

Air-stable and freestanding lithium alloy/graphene foil as an alternative to lithium metal anodes

DOE PAGES

Zhao, Jie; Zhou, Guangmin; Yan, Kai; ...

2017-07-10

Developing high-capacity anodes is a must to improve the energy density of lithium batteries for electric vehicle applications. Alloy anodes are one promising option, but without pre-stored lithium, the overall energy density is limited by the low-capacity lithium metal oxide cathodes. Recently, lithium metal has been revived as a high-capacity anode, but faces several challenges owing to its high reactivity and uncontrolled dendrite growth. Here, we show a series of Li-containing foils inheriting the desirable properties of alloy anodes and pure metal anodes. They consist of densely packed Li xM (M = Si, Sn, or Al) nanoparticles encapsulated by largemore » graphene sheets. With the protection of graphene sheets, the large and freestanding Li xM/graphene foils are stable in different air conditions. With fully expanded Li xSi confined in the highly conductive and chemically stable graphene matrix, this LixSi/graphene foil maintains a stable structure and cyclability in half cells (400 cycles with 98% capacity retention). As a result, this foil is also paired with high-capacity Li-free V 2O 5 and sulfur cathodes to achieve stable full-cell cycling.« less

Air-stable and freestanding lithium alloy/graphene foil as an alternative to lithium metal anodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Jie; Zhou, Guangmin; Yan, Kai

Developing high-capacity anodes is a must to improve the energy density of lithium batteries for electric vehicle applications. Alloy anodes are one promising option, but without pre-stored lithium, the overall energy density is limited by the low-capacity lithium metal oxide cathodes. Recently, lithium metal has been revived as a high-capacity anode, but faces several challenges owing to its high reactivity and uncontrolled dendrite growth. Here, we show a series of Li-containing foils inheriting the desirable properties of alloy anodes and pure metal anodes. They consist of densely packed Li xM (M = Si, Sn, or Al) nanoparticles encapsulated by largemore » graphene sheets. With the protection of graphene sheets, the large and freestanding Li xM/graphene foils are stable in different air conditions. With fully expanded Li xSi confined in the highly conductive and chemically stable graphene matrix, this LixSi/graphene foil maintains a stable structure and cyclability in half cells (400 cycles with 98% capacity retention). As a result, this foil is also paired with high-capacity Li-free V 2O 5 and sulfur cathodes to achieve stable full-cell cycling.« less

Principles for computational design of binding antibodies

PubMed Central

Pszolla, M. Gabriele; Lapidoth, Gideon D.; Norn, Christoffer; Dym, Orly; Unger, Tamar; Albeck, Shira; Tyka, Michael D.; Fleishman, Sarel J.

2017-01-01

Natural proteins must both fold into a stable conformation and exert their molecular function. To date, computational design has successfully produced stable and atomically accurate proteins by using so-called “ideal” folds rich in regular secondary structures and almost devoid of loops and destabilizing elements, such as cavities. Molecular function, such as binding and catalysis, however, often demands nonideal features, including large and irregular loops and buried polar interaction networks, which have remained challenging for fold design. Through five design/experiment cycles, we learned principles for designing stable and functional antibody variable fragments (Fvs). Specifically, we (i) used sequence-design constraints derived from antibody multiple-sequence alignments, and (ii) during backbone design, maintained stabilizing interactions observed in natural antibodies between the framework and loops of complementarity-determining regions (CDRs) 1 and 2. Designed Fvs bound their ligands with midnanomolar affinities and were as stable as natural antibodies, despite having >30 mutations from mammalian antibody germlines. Furthermore, crystallographic analysis demonstrated atomic accuracy throughout the framework and in four of six CDRs in one design and atomic accuracy in the entire Fv in another. The principles we learned are general, and can be implemented to design other nonideal folds, generating stable, specific, and precise antibodies and enzymes. PMID:28973872

A mechanism that maintains alternative life histories in a loggerhead sea turtle population.

PubMed

Hatase, Hideo; Omuta, Kazuyoshi; Tsukamoto, Katsumi

2013-11-01

Intrapopulation variation in habitat use is commonly seen among mobile animals, yet the mechanisms maintaining it have rarely been researched among untrackable species. To investigate how alternative life histories are maintained in a population of the loggerhead sea turtle (Caretta caretta), cumulative reproductive output was evaluated and compared between small planktivores inhabiting oceanic areas (with water depths > 200 m) and large benthivores inhabiting neritic areas (depths < 200 m) that sympatrically nested at Yakushima Island, Japan, from 1986 to 2011. In total, 362 nesting females sampled in three different years were classified into the two foraging groups based on stable isotope ratios in egg yolks. There were significant differences between the two foraging groups in most recorded life history parameters (clutch size, clutch frequency, breeding frequency, and remigration intervals), with the exception of emergence success. We did not find evidence of life history trade-offs, nor age-related changes in fecundity. Over the 26-year study period, we calculated a 2.4-fold greater reproductive output for neritic foragers than for oceanic ones, accounting for breeding and clutch frequency. Temporal consistencies in stable isotope ratios and remigration intervals within females suggested that female Japanese loggerheads show fidelity to respective foraging habitats throughout the adult stage. The large difference in productivity between the two groups was unlikely to be offset by the difference in survival during the period from aboveground emergence to first reproduction, suggesting that oceanic foragers have a lower level of fitness than neritic ones. Together with an absence of genetic structure between foraging groups, we infer that alternative life histories in a loggerhead turtle population are maintained by a conditional strategy.

Physical activity and healthy weight maintenance from childhood to adulthood.

PubMed

Cleland, Verity J; Dwyer, Terence; Venn, Alison J

2008-06-01

The objective of this study was to determine whether change in physical activity was associated with maintaining a healthy weight from childhood to adulthood. This prospective cohort study examined 1,594 young Australian adults (48.9% female) aged 27-36 years who were first examined at age 9-15 years as part of a national health and fitness survey. BMI was calculated from measured height and weight, and physical activity was self-reported at both time points; pedometers were also used at follow-up. Change in physical activity was characterized by calculating the difference between baseline and follow-up z-scores. Change scores were categorized as decreasing (large, moderate), stable, or increasing (large, moderate). Healthy weight was defined in childhood as a BMI less than international overweight cutoff points, and in adulthood as BMI<25 kg/m(2). Healthy weight maintainers were healthy weight at both time points. Compared with those who demonstrated large relative decreases in physical activity, females in all other groups were 25-37% more likely to be healthy weight maintainers, although associations differed according to the physical activity measure used at follow-up and few reached statistical significance. Although younger males whose relative physical activity moderately or largely increased were 27-34% more likely to be healthy weight maintainers than those whose relative physical activity largely decreased, differences were not statistically significant. In conclusion, relatively increasing and stable physical activity from childhood to adulthood was only weakly associated with healthy weight maintenance. Examining personal, social, and environmental factors associated with healthy weight maintenance will be an important next step in understanding why some groups avoid becoming overweight.

[Population change and social organization].

PubMed

Tu, J C

1986-06-01

This paper, published in Taiwan in June, 1986, studies the impact of demographic changes on social organization through stable population theory as applied to the USA. The stable population model indicates a constant age differential between death ratio and birth ratio maintained for a period of time in a given population. Since the 1950's, the population growth rate in the US has been 1.5%; social security tax revenue should increase 50% to maintain equilibrium. According to the US Census Bureau, in 1940, 11 people in 100 were age 65 or over; in 1980, 19 per 100; and 1 estimate places 32 in 100 over 65 in the year 2030. In 90 years the proportion of senior citizens will increase 3 times; social security taxes should consequently also increase 3 times. The stable population model would mean that social security tax should double its current rate to maintain equilibrium. However, based on the actual change in the population's age structure, social security tax should in fact increase at least 3 times. From 1940 to the present, social security tax revenue has already increased 3 times. Turning to education, in 1961, 4.39 million babies were born in the US. By the mid-1970's, births had slowed to an annual average of 3 million. The decrease in number of university students and posts available to Ph.Ds follows the birth rate change of 20 years earlier. Many graduate institutions will be influenced by this decrease in births. From another perspective, the birth rate decrease has also reduced the educational burden on society, and should provide more opportunities and resources. However, in the American educational system, research opportunities are determined by teaching positions which are dependent upon university enrollment figures. The US Census Bureau predicts that enrollment rates must double in order to compensate for the decrease in university age population.

Design, fabrication and performance evaluation of an integrated reformed methanol fuel cell for portable use

NASA Astrophysics Data System (ADS)

Zhang, Shubin; Zhang, Yufeng; Chen, Junyu; Yin, Congwen; Liu, Xiaowei

2018-06-01

In this paper, an integrated reformed methanol fuel cell (RMFC) as a portable power source is designed, fabricated and tested. The RMFC consists of a methanol steam reformer (MSR), a high temperature proton exchange membrane fuel cell (HT-PEMFC) stack, a microcontroller unit (MCU) and other auxiliaries. First, a system model based on Matlab/Simulink is established to investigate the mass and energy transport characteristics within the whole system. The simulation results suggest a hydrogen flow rate of at least 670 sccm is needed for the system to output 30 W and simultaneously maintain thermal equilibrium. Second, a metallic MSR and an HT-PEMFC stack with 12 cells are fabricated and tested. The tests show that the RMFC system is able to function normally when the performances of all the components meet the minimum requirements. At last, in the experiment of successfully powering a laptop, the RMFC system exhibits a stable performance during the complete work flow of all the phases, namely start-up, output and shutdown. Moreover, with a conservative design of 20 W power rating, maximum energy conversion efficiency of the RMFC system can be achieved (36%), and good stability in long-term operation is shown.

Survey of Constellation-Era LOX/Methane Development Activities and Future Development Needs

NASA Technical Reports Server (NTRS)

Marshall, William M.; Stiegemeier, Benjamin; Greene, Sandra Elam; Hurlbert, Eric A.

2017-01-01

NASA formed the Constellation Program in 2005 to achieve the objectives of maintaining American presence in low-Earth orbit, returning to the moon for purposes of establishing an outpost, and laying the foundation to explore Mars and beyond in the first half of the 21st century. The Exploration Technology Development Program (ETDP) was formulated to address the technology needs to address Constellation architecture decisions. The Propellants and Cryogenic Advanced Development (PCAD) project was tasked with risk mitigation of specific propulsion related technologies to support ETDP. Propulsion systems were identified as critical technologies owing to the high gear-ratio of lunar Mars landers Cryogenic propellants offer performance advantage over storables (NTOMMH) Mass savings translate to greater payload capacity In-situ production of propellant an attractive feature; methane and oxygen identified as possible Martian in-situ propellants New technologies were required to meet more difficult missions High performance LOX/LH2 deep throttle descent engines High performance LOX/LCH4 ascent main and reaction control system (RCS) engines The PCAD project sought to provide those technologies through Reliable ignition pulse RCS Fast start High efficiency engines Stable deep throttling.

Synthesis and electrochemical characterization of Li 1.05RE xCr yMn 2- x- yO 4 spinel as cathode material for rechargeable Li-battery

NASA Astrophysics Data System (ADS)

Xie, Yanting; Yang, Rudong; Yan, Lan; Qi, Lu; Dai, Kehua; He, Ping

The spinel phases of Li 1.05RE xCr yMn 2- x- yO 4 (RE = Sc, Ce, Pr, Tb; 0 ≤ x ≤ 0.05; 0 ≤ y ≤ 0.1) were prepared by a soft chemical method. The structural and electrochemical properties of Li 1.05RE xCr yMn 2- x- yO 4 were investigated by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and charge-discharge experiments. Rare earth element-Sc and transition metal-Cr as co-substituents stabilize the spinel framework and improve charge-discharge performance. For Li 1.05Sc 0.01Cr 0.03Mn 1.96O 4, the capacity of the cell maintained 95% of the initial capacity at the 80th cycle. The rare earth elements of the variable valent metals such as Ce 3+/4+, Pr 3+/4+, Tb 3+/4+ with transition metal Cr 3+ as co-substituent do not stable framework of spinel or improve the cycling performance. Cyclic voltammetry (CV) were measured to provide clues for the improved cycling performance of cathode electrodes.

Testing the predictions of coping styles theory in threespined sticklebacks

PubMed Central

Bensky, Miles K.; Paitz, Ryan; Pereira, Laura; Bell, Alison M.

2017-01-01

Coping styles theory provides a framework for understanding individual variation in how animals respond to environmental change, and predicts how individual differences in stress responsiveness and behavior might relate to cognitive differences. According to coping styles theory, proactive individuals are bolder, less reactive to stressors, and more routinized than their reactive counterparts. A key tenet of coping styles theory is that variation in coping styles is maintained by tradeoffs with behavioral flexibility: proactive individuals excel in stable environments while more flexible, reactive individuals perform better in variable environments. Here, we assess evidence for coping styles within a natural population of threespined sticklebacks (Gasterosteus aculeatus). We developed a criterion-based learning paradigm to evaluate individual variation in initial and reversal learning. We observed strong individual differences in boldness, cortisol production, and learning performance. Consistent with coping styles, fish that released more cortisol were more timid in response to a predator attack and slower to learn a color discrimination task. However, there was no evidence that reactive individuals performed better when the environment changed (when the rewarded color was reversed). The failure to detect trade-offs between behavioral routinization and flexibility prompts other explanations for the maintenance of differing coping styles. PMID:28017848

Reliability over time of EEG-based mental workload evaluation during Air Traffic Management (ATM) tasks.

PubMed

Arico, Pietro; Borghini, Gianluca; Di Flumeri, Gianluca; Colosimo, Alfredo; Graziani, Ilenia; Imbert, Jean-Paul; Granger, Geraud; Benhacene, Railene; Terenzi, Michela; Pozzi, Simone; Babiloni, Fabio

2015-08-01

Machine-learning approaches for mental workload (MW) estimation by using the user brain activity went through a rapid expansion in the last decades. In fact, these techniques allow now to measure the MW with a high time resolution (e.g. few seconds). Despite such advancements, one of the outstanding problems of these techniques regards their ability to maintain a high reliability over time (e.g. high accuracy of classification even across consecutive days) without performing any recalibration procedure. Such characteristic will be highly desirable in real world applications, in which human operators could use such approach without undergo a daily training of the device. In this work, we reported that if a simple classifier is calibrated by using a low number of brain spectral features, between those ones strictly related to the MW (i.e. Frontal and Occipital Theta and Parietal Alpha rhythms), those features will make the classifier performance stable over time. In other words, the discrimination accuracy achieved by the classifier will not degrade significantly across different days (i.e. until one week). The methodology has been tested on twelve Air Traffic Controls (ATCOs) trainees while performing different Air Traffic Management (ATM) scenarios under three different difficulty levels.

Nickel-based anode with water storage capability to mitigate carbon deposition for direct ethanol solid oxide fuel cells.

PubMed

Wang, Wei; Su, Chao; Ran, Ran; Zhao, Bote; Shao, Zongping; Tade, Moses O; Liu, Shaomin

2014-06-01

The potential to use ethanol as a fuel places solid oxide fuel cells (SOFCs) as a sustainable technology for clean energy delivery because of the renewable features of ethanol versus hydrogen. In this work, we developed a new class of anode catalyst exemplified by Ni+BaZr0.4Ce0.4Y0.2O3 (Ni+BZCY) with a water storage capability to overcome the persistent problem of carbon deposition. Ni+BZCY performed very well in catalytic efficiency, water storage capability and coking resistance tests. A stable and high power output was well maintained with a peak power density of 750 mW cm(-2) at 750 °C. The SOFC with the new robust anode performed for seven days without any sign of performance decay, whereas SOFCs with conventional anodes failed in less than 2 h because of significant carbon deposition. Our findings indicate the potential applications of these water storage cermets as catalysts in hydrocarbon reforming and as anodes for SOFCs that operate directly on hydrocarbons. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Orbital management and design considerations for NiCd satellite power systems

NASA Technical Reports Server (NTRS)

Tausch, Benjamin J., II

1994-01-01

Several recently manufactured 50 and 60 ampere hour aerospace NiCd battery cell lots, produced by Gates Aerospace Batteries, are prone to premature on orbit performance degradation. The failure mechanism is cadmium migration, and the consequent development of soft shorts. A Martin Marietta Astronautics satellite program instituted an orbital management strategy for a set of these batteries that reduced the rate of degradation and brought the system to stable operation. This strategy involves: (1) minimizing the accumulated battery overcharge; (2) regular discharge exercises; and (3) periodic battery reconditioning. Because of changes in the NiCd cell manufacturing process, the actual performance of subsequent lots of NiCd cells is open to question. Future NiCd based power system designs should therefore allow for fine control of charge parameters, and an on orbit battery reconditioning capability. To minimize risk, it is much better to perform a full life test to qualify the cells before launch, rather than in parallel with orbital operations. If there are any changes in the manufacturing process of cells, it is extremely important to maintain very strong cognizance of secondary subcontractors, recognizing that the cell and battery manufacturing discipline is easily atrophied.

Carbon Cathodes in Rechargeable Lithium-Oxygen Batteries Based on Double-Lithium-Salt Electrolytes.

PubMed

Yoo, Eunjoo; Zhou, Haoshen

2016-06-08

The use of carbon materials as air electrodes in lithium-oxygen (Li-O2 ) batteries is known to be advantageous owing to their good conductivity and because they offer sites suitable for the reversible electrode reactions. However, the exact influence of carbon materials on the electrochemical performance of Li-O2 batteries is not clear. In this study the electrochemical performance of four different types of carbon materials (multiwalled carbon nanotubes (MWCNTs), CMK-3, graphene nanosheets (GNSs), and Ketjen Black (KB)) as air electrodes is examined. We find that a Li-O2 cell based on an electrode of multiwalled carbon nanotubes (MWCNTs) demonstrates good rate performance and cycle stability, when using LiNO3 -LiTFSI/DMSO as electrolyte. Li-O2 cells based on such MWCNT electrodes, with a cut-off capacity of 1000 mAh g(-1) at 500 mA g(-1) , can undergo around 90 cycles without obvious losses of capacity. Even when the discharge depth is increased to 2000 mA h g(-1) , stable cycling is maintained for 45 cycles at a charge potential below 4.0 V. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

EFFECTIVE INDICES FOR MONITORING MENTAL WORKLOAD WHILE PERFORMING MULTIPLE TASKS.

PubMed

Hsu, Bin-Wei; Wang, Mao-Jiun J; Chen, Chi-Yuan; Chen, Fang

2015-08-01

This study identified several physiological indices that can accurately monitor mental workload while participants performed multiple tasks with the strategy of maintaining stable performance and maximizing accuracy. Thirty male participants completed three 10-min. simulated multitasks: MATB (Multi-Attribute Task Battery) with three workload levels. Twenty-five commonly used mental workload measures were collected, including heart rate, 12 HRV (heart rate variability), 10 EEG (electroencephalography) indices (α, β, θ, α/θ, θ/β from O1-O2 and F4-C4), and two subjective measures. Analyses of index sensitivity showed that two EEG indices, θ and α/θ (F4-C4), one time-domain HRV-SDNN (standard deviation of inter-beat intervals), and four frequency-domain HRV: VLF (very low frequency), LF (low frequency), %HF (percentage of high frequency), and LF/HF were sensitive to differentiate high workload. EEG α/θ (F4-C4) and LF/HF were most effective for monitoring high mental workload. LF/HF showed the highest correlations with other physiological indices. EEG α/θ (F4-C4) showed strong correlations with subjective measures across different mental workload levels. Operation strategy would affect the sensitivity of EEG α (F4-C4) and HF.

Characterizing the Effective Bandwidth of Nonlinear Vibratory Energy Harvesters Possessing Multiple Stable Equilibria

NASA Astrophysics Data System (ADS)

Panyam Mohan Ram, Meghashyam

In the last few years, advances in micro-fabrication technologies have lead to the development of low-power electronic devices spanning critical fields related to sensing, data transmission, and medical implants. Unfortunately, effective utilization of these devices is currently hindered by their reliance on batteries. In many of these applications, batteries may not be a viable choice as they have a fixed storage capacity and need to be constantly replaced or recharged. In light of such challenges, several novel concepts for micro-power generation have been recently introduced to harness, otherwise, wasted ambient energy from the environment and maintain these low-power devices. Vibratory energy harvesting is one such concept which has received significant attention in recent years. While linear vibratory energy harvesters have been well studied in the literature and their performance metrics have been established, recent research has focused on deliberate introduction of stiffness nonlinearities into the design of these devices. It has been shown that, nonlinear energy harvesters have a wider steady-state frequency bandwidth as compared to their linear counterparts, leading to the premise that they can used to improve performance, and decrease sensitivity to variations in the design and excitation parameters. This dissertation aims to investigate this premise by developing an analytical framework to study the influence of stiffness nonlinearities on the performance and effective bandwidth of nonlinear vibratory energy harvesters. To achieve this goal, the dissertation is divided into three parts. The first part investigates the performance of bi-stable energy harvesters possessing a symmetric quartic potential energy function under harmonic excitations and carries out a detailed analysis to define their effective frequency bandwidth. The second part investigates the relative performance of mono- and bi-stable energy harvesters under optimal electric loading conditions. The third part investigates the response and performance of tri-stable energy harvesters possessing a symmetric hexic potential function under harmonic excitations and provides a detailed analysis to approximate their effective frequency bandwidth. As a platform to achieve these objectives, a piezoelectric nonlinear energy harvester consisting of a uni-morph cantilever beam is considered. Stiffness nonlinearities are introduced into the harvester's design by applying a static magnetic field near the tip of the beam. Experimental studies performed on the proposed harvester are presented to validate some of the theoretical findings. Since nonlinear energy harvesters exhibit complex and non-unique responses, it is demonstrated that a careful choice of the design parameters namely, the shape of the potential function and the electromechanical coupling is necessary to widen their effective frequency bandwidth. Specifically, it is shown that, decreasing the electromechanical coupling and/or designing the potential energy function to have shallow wells, widens the effective frequency bandwidth for a given excitation level. However, this comes at the expense of the output power which decreases under these design conditions. It is also shown that the ratio between the mechanical period and time constant of the harvesting circuit has negligible influence on the effective frequency bandwidth but has considerable effect on the associated magnitude of the output power.

Hydroxyapatite Nanowire-Based All-Weather Flexible Electrically Conductive Paper with Superhydrophobic and Flame-Retardant Properties.

PubMed

Chen, Fei-Fei; Zhu, Ying-Jie; Xiong, Zhi-Chao; Dong, Li-Ying; Chen, Feng; Lu, Bing-Qiang; Yang, Ri-Long

2017-11-15

How to survive under various harsh working conditions is a key challenge for flexible electronic devices because their performances are always susceptible to environments. Herein, we demonstrate the novel design and fabrication of a new kind of the all-weather flexible electrically conductive paper based on ultralong hydroxyapatite nanowires (HNs) with unique combination of the superhydrophobic surface, electrothermal effect, and flame retardancy. The superhydrophobic surface with water repellency stabilizes the electrically conductive performance of the paper in water. For example, the electrical current through the superhydrophobic paper onto which water droplets are deposited shows a little change (0.38%), and the electrical performance is steady as well even when the paper is immersed in water for 120 s (just 3.65% change). In addition, the intrinsic electrothermal effect of the electrically conductive paper can efficiently heat the paper to reach a high temperature, for example, 224.25 °C, within 10 s. The synergistic effect between the electrothermal effect and superhydrophobic surface accelerates the melting and removal of ice on the heated electrically conductive paper. Deicing efficiency of the heated superhydrophobic electrically conductive paper is ∼4.5 times that of the unheated superhydrophobic electrically conductive paper and ∼10.4 times that of the heated superhydrophilic paper. More importantly, benefiting from fire-resistant ultralong HNs, thermally stable Ketjen black, and Si-O backbone of poly(dimethylsiloxane), we demonstrate the stable and continuous service of the as-prepared electrically conductive paper in the flame for as long as 7 min. The electrical performance of the electrically conductive paper after flame treatment can maintain as high as 90.60% of the original value. The rational design of the electrically conductive paper with suitable building materials and structure demonstrated here will give an inspiration for the development of new kinds of all-weather flexible electronic devices that can work under harsh conditions.

Testing projected wild bee distributions in agricultural habitats: predictive power depends on species traits and habitat type.

PubMed

Marshall, Leon; Carvalheiro, Luísa G; Aguirre-Gutiérrez, Jesús; Bos, Merijn; de Groot, G Arjen; Kleijn, David; Potts, Simon G; Reemer, Menno; Roberts, Stuart; Scheper, Jeroen; Biesmeijer, Jacobus C

2015-10-01

Species distribution models (SDM) are increasingly used to understand the factors that regulate variation in biodiversity patterns and to help plan conservation strategies. However, these models are rarely validated with independently collected data and it is unclear whether SDM performance is maintained across distinct habitats and for species with different functional traits. Highly mobile species, such as bees, can be particularly challenging to model. Here, we use independent sets of occurrence data collected systematically in several agricultural habitats to test how the predictive performance of SDMs for wild bee species depends on species traits, habitat type, and sampling technique. We used a species distribution modeling approach parametrized for the Netherlands, with presence records from 1990 to 2010 for 193 Dutch wild bees. For each species, we built a Maxent model based on 13 climate and landscape variables. We tested the predictive performance of the SDMs with independent datasets collected from orchards and arable fields across the Netherlands from 2010 to 2013, using transect surveys or pan traps. Model predictive performance depended on species traits and habitat type. Occurrence of bee species specialized in habitat and diet was better predicted than generalist bees. Predictions of habitat suitability were also more precise for habitats that are temporally more stable (orchards) than for habitats that suffer regular alterations (arable), particularly for small, solitary bees. As a conservation tool, SDMs are best suited to modeling rarer, specialist species than more generalist and will work best in long-term stable habitats. The variability of complex, short-term habitats is difficult to capture in such models and historical land use generally has low thematic resolution. To improve SDMs' usefulness, models require explanatory variables and collection data that include detailed landscape characteristics, for example, variability of crops and flower availability. Additionally, testing SDMs with field surveys should involve multiple collection techniques.

Stereoselective quantification of methadone and a d(6)-labeled isotopomer using high performance liquid chromatography-atmospheric pressure chemical ionization mass-spectrometry: application to a pharmacokinetic study in a methadone maintained subject.

PubMed

Foster, David J R; Morton, Erin B; Heinkele, Georg; Mürdter, Thomas E; Somogyi, Andrew A

2006-08-01

There is evidence that the apparent oral clearance of rac-methadone is induced during the early phase of methadone maintenance treatment. However, it is not known if this is due to changes in bioavailability or if this phenomenon is stereoselective. This knowledge can be obtained by administering a dose of stable-labeled methadone at selected times during ongoing treatment. Therefore, the authors developed a stereoselective high performance liquid chromatography-atmospheric pressure chemical ionization mass-spectrometry assay for the quantification of the enantiomers of methadone and a d(6)-labeled isotopomer. The compounds were quantified in a single assay after liquid-liquid extraction and stereoselective high performance liquid chromatograph with atmospheric pressure chemical ionization-mass spectrometry detection. The following ions were monitored: m/z 310.15 for unlabeled methadone; m/z 316.15 for methadone-d(6); and m/z 313.15 for the methadone-d(3) (internal standard). Calibration curves ranged from 0.5 to 75 ng/mL for each compound. Extraction recovery was approximately 80% for all analytes, without evidence of differences between the unlabeled and stable-labeled compounds or concentration dependency. Minor ion promotion was observed (<15%) but this was identical for all analytes including the d(3)-labeled internal standard, with peak area ratios in extracted samples identical to control injections. The isotopomers did not alter each others' ionisation, even at 10:1 concentration ratios, and 10-fold diluted samples were within 10% of the nominal concentration. Assay performance was acceptable, with interassay and intra-assay bias and precision <10% for all compounds, including the upper and lower limits of quantitation. In conclusion, the assay was successfully applied to quantify the concentration of the methadone enantiomers of both orally administered unlabeled methadone and an intravenous 5 mg dose of methadone-d(6) in a patient receiving chronic oral methadone maintenance therapy.

Reciprocal Prioritization to Dietary Glycans by Gut Bacteria in a Competitive Environment Promotes Stable Coexistence.

PubMed

Tuncil, Yunus E; Xiao, Yao; Porter, Nathan T; Reuhs, Bradley L; Martens, Eric C; Hamaker, Bruce R

2017-10-10

When presented with nutrient mixtures, several human gut Bacteroides species exhibit hierarchical utilization of glycans through a phenomenon that resembles catabolite repression. However, it is unclear how closely these observed physiological changes, often measured by altered transcription of glycan utilization genes, mirror actual glycan depletion. To understand the glycan prioritization strategies of two closely related human gut symbionts, Bacteroides ovatus and Bacteroides thetaiotaomicron , we performed a series of time course assays in which both species were individually grown in a medium with six different glycans that both species can degrade. Disappearance of the substrates and transcription of the corresponding polysaccharide utilization loci (PULs) were measured. Each species utilized some glycans before others, but with different priorities per species, providing insight into species-specific hierarchical preferences. In general, the presence of highly prioritized glycans repressed transcription of genes involved in utilizing lower-priority nutrients. However, transcriptional sensitivity to some glycans varied relative to the residual concentration in the medium, with some PULs that target high-priority substrates remaining highly expressed even after their target glycan had been mostly depleted. Coculturing of these organisms in the same mixture showed that the hierarchical orders generally remained the same, promoting stable coexistence. Polymer length was found to be a contributing factor for glycan utilization, thereby affecting its place in the hierarchy. Our findings not only elucidate how B. ovatus and B. thetaiotaomicron strategically access glycans to maintain coexistence but also support the prioritization of carbohydrate utilization based on carbohydrate structure, advancing our understanding of the relationships between diet and the gut microbiome. IMPORTANCE The microorganisms that reside in the human colon fulfill their energy requirements mainly from diet- and host-derived complex carbohydrates. Members of this ecosystem possess poorly understood strategies to prioritize and compete for these nutrients. Based on direct carbohydrate measurements and corresponding transcriptional analyses, our findings showed that individual bacterial species exhibit different preferences for the same set of glycans and that this prioritization is maintained in a competitive environment, which may promote stable coexistence. Such understanding of gut bacterial glycan utilization will be essential to eliciting predictable changes in the gut microbiota to improve health through the diet. Copyright © 2017 Tuncil et al.

A Diffusive Homeostatic Signal Maintains Neural Heterogeneity and Responsiveness in Cortical Networks

PubMed Central

Sweeney, Yann; Hellgren Kotaleski, Jeanette; Hennig, Matthias H.

2015-01-01

Gaseous neurotransmitters such as nitric oxide (NO) provide a unique and often overlooked mechanism for neurons to communicate through diffusion within a network, independent of synaptic connectivity. NO provides homeostatic control of intrinsic excitability. Here we conduct a theoretical investigation of the distinguishing roles of NO-mediated diffusive homeostasis in comparison with canonical non-diffusive homeostasis in cortical networks. We find that both forms of homeostasis provide a robust mechanism for maintaining stable activity following perturbations. However, the resulting networks differ, with diffusive homeostasis maintaining substantial heterogeneity in activity levels of individual neurons, a feature disrupted in networks with non-diffusive homeostasis. This results in networks capable of representing input heterogeneity, and linearly responding over a broader range of inputs than those undergoing non-diffusive homeostasis. We further show that these properties are preserved when homeostatic and Hebbian plasticity are combined. These results suggest a mechanism for dynamically maintaining neural heterogeneity, and expose computational advantages of non-local homeostatic processes. PMID:26158556

Use of oxygen-18 and deuterium to assess the hydrology of groundwater-lake systems: Chapter 3: Advances in chemistry

USGS Publications Warehouse

Krabbenhoft, David P.; Bowser, Carl J.; Kendall, Carol; Gat, Joel

2009-01-01

A thorough understanding of a lake's hydrology is essential for many lake studies. In some situations the interactions between groundwater systems and lakes are complex; in other cases the hydrology of a multilake system needs to be quantified. In such places, stable isotopes offer an alternative to the more traditional piezometer networks, which are costly to install and time-consuming to maintain. The stable-isotope mass-balance relations presented here can be used to estimate groundwater exchange rates for individual lakes and geographically clustered lakes. These relations also can be used to estimate other hydrological factors, such as average relative humidity. In places where the groundwater system is unstable (e.g., where flow reversals occur), natural solute tracers may provide a better alternative than stable isotopes for estimating rates of groundwater flow to and from lakes.

Phase stable RF transport system

DOEpatents

Curtin, Michael T.; Natter, Eckard F.; Denney, Peter M.

1992-01-01

An RF transport system delivers a phase-stable RF signal to a load, such as an RF cavity of a charged particle accelerator. A circuit generates a calibration signal at an odd multiple frequency of the RF signal where the calibration signal is superimposed with the RF signal on a common cable that connects the RF signal with the load. Signal isolating diplexers are located at both the RF signal source end and load end of the common cable to enable the calibration to be inserted and extracted from the cable signals without any affect on the RF signal. Any phase shift in the calibration signal during traverse of the common cable is then functionally related to the phase shift in the RF signal. The calibration phase shift is used to control a phase shifter for the RF signal to maintain a stable RF signal at the load.

Achieving Stable Radiation Pressure Acceleration of Heavy Ions via Successive Electron Replenishment from Ionization of a High-Z Material Coating

NASA Astrophysics Data System (ADS)

Shen, X. F.; Qiao, B.; Zhang, H.; Kar, S.; Zhou, C. T.; Chang, H. X.; Borghesi, M.; He, X. T.

2017-05-01

A method to achieve stable radiation pressure acceleration (RPA) of heavy ions from laser-irradiated ultrathin foils is proposed, where a high-Z material coating in front is used. The coated high-Z material, acting as a moving electron repository, continuously replenishes the accelerating heavy ion foil with comoving electrons in the light-sail acceleration stage due to its successive ionization under laser fields with Gaussian temporal profile. As a result, the detrimental effects such as foil deformation and electron loss induced by the Rayleigh-Taylor-like and other instabilities in RPA are significantly offset and suppressed so that stable acceleration of heavy ions are maintained. Particle-in-cell simulations show that a monoenergetic Al13 + beam with peak energy 3.8 GeV and particle number 1 010 (charge >20 nC ) can be obtained at intensity 1 022 W /cm2 .

An In Situ One-Pot Synthetic Approach towards Multivariate Zirconium MOFs.

PubMed

Sun, Yujia; Sun, Lixian; Feng, Dawei; Zhou, Hong-Cai

2016-05-23

Chemically highly stable MOFs incorporating multiple functionalities are of great interest for applications under harsh environments. Herein, we presented a facile one-pot synthetic strategy to incorporate multiple functionalities into stable Zr-MOFs from mixed ligands of different geometry and connectivity. Via our strategy, tetratopic tetrakis(4-carboxyphenyl)porphyrin (TCPP) ligands were successfully integrated into UiO-66 while maintaining the crystal structure, morphology, and ultrahigh chemical stability of UiO-66. The amount of incorporated TCPP is controllable. Through various combinations of BDC derivatives and TCPP, 49 MOFs with multiple functionalities were obtained. Among them, MOFs modified with FeTCPPCl were demonstrated to be catalytically active for the oxidation of ABTS. We anticipate our strategy to provide a facile route to introduce multiple functionalities into stable Zr-MOFs for a wide variety of potential applications. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thermally Stable, Piezoelectric and Pyroelectric Polymeric Substrates and Method Relating Thereto

NASA Technical Reports Server (NTRS)

Simpson, Joycelyn O. (Inventor); St.Claire, Terry L. (Inventor)

2002-01-01

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared, This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers, acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors. in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches. adjustable fresnel lenses, speakers, tactile sensors, weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 100 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrates; heating the metal electrode coated polymeric substrate in a low dielectric medium; applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Thermally Stable, Piezoelectric and Pyroelectric Polymeric Substrates

NASA Technical Reports Server (NTRS)

Simpson, Joycely O. (Inventor); St.Clair, Terry L. (Inventor)

1999-01-01

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared. This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers. acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors, in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches, adjustable fresnel lenses, speakers, tactile sensors. weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 1000 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrate; heating the metal electrode coated polymeric substrate in a low dielectric medium; applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Method of Making Thermally Stable, Piezoelectric and Proelectric Polymeric Substrates

NASA Technical Reports Server (NTRS)

Simpson, Joycelyn O. (Inventor); St.Clair, Terry L. (Inventor)

1999-01-01

A thermally stable, piezoelectric and pyroelectric polymeric substrate was prepared. This thermally stable, piezoelectric and pyroelectric polymeric substrate may be used to prepare electromechanical transducers, thermomechanical transducers, accelerometers, acoustic sensors, infrared sensors, pressure sensors, vibration sensors, impact sensors. in-situ temperature sensors, in-situ stress/strain sensors, micro actuators, switches, adjustable fresnel lenses, speakers, tactile sensors, weather sensors, micro positioners, ultrasonic devices, power generators, tunable reflectors, microphones, and hydrophones. The process for preparing these polymeric substrates includes: providing a polymeric substrate having a softening temperature greater than 100 C; depositing a metal electrode material onto the polymer film; attaching a plurality of electrical leads to the metal electrode coated polymeric substrate; heating the metal electrode coated polymeric substrate in a low dielectric medium: applying a voltage to the heated metal electrode coated polymeric substrate to induce polarization; and cooling the polarized metal electrode coated polymeric electrode while maintaining a constant voltage.

Modeling hemoglobin at optical frequency using the unconditionally stable fundamental ADI-FDTD method.

PubMed

Heh, Ding Yu; Tan, Eng Leong

2011-04-12

This paper presents the modeling of hemoglobin at optical frequency (250 nm - 1000 nm) using the unconditionally stable fundamental alternating-direction-implicit finite-difference time-domain (FADI-FDTD) method. An accurate model based on complex conjugate pole-residue pairs is proposed to model the complex permittivity of hemoglobin at optical frequency. Two hemoglobin concentrations at 15 g/dL and 33 g/dL are considered. The model is then incorporated into the FADI-FDTD method for solving electromagnetic problems involving interaction of light with hemoglobin. The computation of transmission and reflection coefficients of a half space hemoglobin medium using the FADI-FDTD validates the accuracy of our model and method. The specific absorption rate (SAR) distribution of human capillary at optical frequency is also shown. While maintaining accuracy, the unconditionally stable FADI-FDTD method exhibits high efficiency in modeling hemoglobin.

Modeling hemoglobin at optical frequency using the unconditionally stable fundamental ADI-FDTD method

PubMed Central

Heh, Ding Yu; Tan, Eng Leong

2011-01-01

This paper presents the modeling of hemoglobin at optical frequency (250 nm – 1000 nm) using the unconditionally stable fundamental alternating-direction-implicit finite-difference time-domain (FADI-FDTD) method. An accurate model based on complex conjugate pole-residue pairs is proposed to model the complex permittivity of hemoglobin at optical frequency. Two hemoglobin concentrations at 15 g/dL and 33 g/dL are considered. The model is then incorporated into the FADI-FDTD method for solving electromagnetic problems involving interaction of light with hemoglobin. The computation of transmission and reflection coefficients of a half space hemoglobin medium using the FADI-FDTD validates the accuracy of our model and method. The specific absorption rate (SAR) distribution of human capillary at optical frequency is also shown. While maintaining accuracy, the unconditionally stable FADI-FDTD method exhibits high efficiency in modeling hemoglobin. PMID:21559129

Stability over Time of Different Methods of Estimating School Performance

ERIC Educational Resources Information Center

Dumay, Xavier; Coe, Rob; Anumendem, Dickson Nkafu

2014-01-01

This paper aims to investigate how stability varies with the approach used in estimating school performance in a large sample of English primary schools. The results show that (a) raw performance is considerably more stable than adjusted performance, which in turn is slightly more stable than growth model estimates; (b) schools' performance…

Metal-Organic Framework Derived Porous Hollow Co3O4/N-C Polyhedron Composite with Excellent Energy Storage Capability.

PubMed

Kang, Wenpei; Zhang, Yu; Fan, Lili; Zhang, Liangliang; Dai, Fangna; Wang, Rongming; Sun, Daofeng

2017-03-29

Metal-organic frameworks (MOFs) derived transition metal oxides exhibit enhanced performance in energy conversion and storage. In this work, porous hollow Co 3 O 4 with N-doped carbon coating (Co 3 O 4 /N-C) polyhedrons have been prepared using cobalt-based MOFs as a sacrificial template. Assembled from tiny nanoparticles and N-doped carbon coating, Co 3 O 4 /N-C composite shortens the diffusion length of Li + /Na + ions and possesses an enhanced conductivity. And the porous and hollow structure is also beneficial for tolerating volume changes in the galvanostatic discharge/charge cycles as lithium/sodium battery anode materials. As a result, it can exhibit impressive cycling and rating performance. At 1000 mA g -1 , the specific capacities maintaine stable values of ∼620 mAh g -1 within 2000 cycles as anodes in lithium ion battery, while the specific capacity keeps at 229 mAh g -1 within 150 cycles as sodium ion battery anode. Our work shows comparable cycling performance in lithium ion battery but even better high-rate cycling stability as sodium ion battery anode. Herein, we provide a facile method to construct high electrochemical performance oxide/N-C composite electrode using new MOFs as sacrificial template.

Evolutionary stability of mutualism: interspecific population regulation as an evolutionarily stable strategy

USGS Publications Warehouse

Holland, J. Nathaniel; DeAngelis, Donald L.; Schultz, Stewart T.

2004-01-01

Interspecific mutualisms are often vulnerable to instability because low benefit : cost ratios can rapidly lead to extinction or to the conversion of mutualism to parasite–host or predator–prey interactions. We hypothesize that the evolutionary stability of mutualism can depend on how benefits and costs to one mutualist vary with the population density of its partner, and that stability can be maintained if a mutualist can influence demographic rates and regulate the population density of its partner. We test this hypothesis in a model of mutualism with key features of senita cactus (Pachycereus schottii) – senita moth (Upiga virescens) interactions, in which benefits of pollination and costs of larval seed consumption to plant fitness depend on pollinator density. We show that plants can maximize their fitness by allocating resources to the production of excess flowers at the expense of fruit. Fruit abortion resulting from excess flower production reduces pre–adult survival of the pollinating seed–consumer, and maintains its density beneath a threshold that would destabilize the mutualism. Such a strategy of excess flower production and fruit abortion is convergent and evolutionarily stable against invasion by cheater plants that produce few flowers and abort few to no fruit. This novel mechanism of achieving evolutionarily stable mutualism, namely interspecific population regulation, is qualitatively different from other mechanisms invoking partner choice or selective rewards, and may be a general process that helps to preserve mutualistic interactions in nature.

Insights in connecting phenotypes in bacteria to coevolutionary information

NASA Astrophysics Data System (ADS)

Cheng, Ryan; Morcos, Faruck; Hayes, Ryan; Helm, Rodney; Levine, Herbert; Onuchic, Jose

It has long been known that protein sequences are far from random. These sequences have been evolutionarily selected to maintain their ability to fold into stable, three-dimensional folded structures as well as their ability to form macromolecular assemblies, perform catalytic functions, etc. For these reasons, there exist quantifiable mutational patterns in the collection of sequence data for a protein family arising from the need to maintain favorable residue-residue interactions to facilitate folding as well as cellular function. Here, we focus on studying the correlated mutational patterns that give rise to interaction specificity in bacterial two-component signaling (TCS) systems. TCS proteins have evolved to be able to preferentially bind and transfer a phosphate group to their signaling partner while avoiding phosphotransfer with non-partners. We infer a Potts model Hamiltonian governing the correlated mutational patterns that are observed in the sequence data of TCS partners and apply this model to recently published in vivo mutational data. Our findings further support the notion that statistical models built from sequence data can be used to predict bacterial phenotypes as well as engineer interaction specificity between non-partner TCS proteins. This research has been supported by the NSF INSPIRE Award (MCB-1241332) and by the CTBP sponsored by the NSF (Grant PHY- 1427654).

Opportunities and strategies to further reduce animal use for Leptospira vaccine potency testing.

PubMed

Walker, A; Srinivas, G B

2013-09-01

Hamsters are routinely infected with virulent Leptospira for two purposes in the regulation of biologics: the performance of Codified potency tests and maintenance of challenge culture for the Codified potency tests. Options for reducing animal use in these processes were explored in a plenary lecture at the "International Workshop on Alternative Methods for Leptospira Vaccine Potency Testing: State of the Science and the Way Forward" held at the Center for Veterinary Biologics in September 2012. The use of validated in vitro potency assays such as those developed by the U.S. Department of Agriculture for Leptospira (L.) canicola, Leptospira grippotyphosa, Leptospira pomona, and Leptospira icterohaemorrhagiae rather than the Codified hamster vaccination-challenge assay was encouraged. Alternatives such as reduced animal numbers in the hamster vaccination-challenge testing were considered for problematic situations. Specifically, the merits of sharing challenge controls, reducing group sizes, and eliminating animals for concurrent challenge dose titration were assessed. Options for maintaining virulent, stable cultures without serial passage through hamsters or with decreased hamster use were also discussed. The maintenance of virulent Leptospira without the use of live animals is especially difficult since a reliable means to maintain virulence after multiple in vitro passages has not yet been identified. Published by Elsevier Ltd.

Protein half-life determines expression of proteostatic networks in podocyte differentiation.

PubMed

Schroeter, Christina B; Koehler, Sybille; Kann, Martin; Schermer, Bernhard; Benzing, Thomas; Brinkkoetter, Paul T; Rinschen, Markus M

2018-04-25

Podocytes are highly specialized, epithelial, postmitotic cells, which maintain the renal filtration barrier. When adapting to considerable metabolic and mechanical stress, podocytes need to accurately maintain their proteome. Immortalized podocyte cell lines are a widely used model for studying podocyte biology in health and disease in vitro. In this study, we performed a comprehensive proteomic analysis of the cultured human podocyte proteome in both proliferative and differentiated conditions at a depth of >7000 proteins. Similar to mouse podocytes, human podocyte differentiation involved a shift in proteostasis: undifferentiated podocytes have high expression of proteasomal proteins, whereas differentiated podocytes have high expression of lysosomal proteins. Additional analyses with pulsed stable-isotope labeling by amino acids in cell culture and protein degradation assays determined protein dynamics and half-lives. These studies unraveled a globally increased stability of proteins in differentiated podocytes. Mitochondrial, cytoskeletal, and membrane proteins were stabilized, particularly in differentiated podocytes. Importantly, protein half-lives strongly contributed to protein abundance in each state. These data suggest that regulation of protein turnover of particular cellular functions determines podocyte differentiation, a paradigm involving mitophagy and, potentially, of importance in conditions of increased podocyte stress and damage.-Schroeter, C. B., Koehler, S., Kann, M., Schermer, B., Benzing, T., Brinkkoetter, P. T., Rinschen, M. M. Protein half-life determines expression of proteostatic networks in podocyte differentiation.

A Fuzzy Technique for Performing Lateral-Axis Formation Flight Navigation Using Wingtip Vortices

NASA Technical Reports Server (NTRS)

Hanson, Curtis E.

2003-01-01

Close formation flight involving aerodynamic coupling through wingtip vortices shows significant promise to improve the efficiency of cooperative aircraft operations. Impediments to the application of this technology include internship communication required to establish precise relative positioning. This report proposes a method for estimating the lateral relative position between two aircraft in close formation flight through real-time estimates of the aerodynamic effects imparted by the leading airplane on the trailing airplane. A fuzzy algorithm is developed to map combinations of vortex-induced drag and roll effects to relative lateral spacing. The algorithm is refined using self-tuning techniques to provide lateral relative position estimates accurate to 14 in., well within the requirement to maintain significant levels of drag reduction. The fuzzy navigation algorithm is integrated with a leader-follower formation flight autopilot in a two-ship F/A-18 simulation with no intership communication modeled. It is shown that in the absence of measurements from the leading airplane the algorithm provides sufficient estimation of lateral formation spacing for the autopilot to maintain stable formation flight within the vortex. Formation autopilot trim commands are used to estimate vortex effects for the algorithm. The fuzzy algorithm is shown to operate satisfactorily with anticipated levels of input uncertainties.

Estimating the economic benefits of maintaining residential lake levels at an irrigation reservoir: A contingent valuation study

NASA Astrophysics Data System (ADS)

Loomis, John; Smith, Adam; Huszar, Paul

2005-08-01

The contingent valuation method (CVM) was used to estimate homeowners' willingness to pay for water leasing to maintain stable lake levels at an irrigation reservoir in a residential neighborhood. A binary logit model was used to analyze households' voter referendum responses for maintaining the lake level. The median willingness to pay (WTP) was found to be $368 per year for lakefront residents and $59 per year for off-lake residents. The median WTP for lakefront residents was significantly different from off-lake residents at the 90% confidence level. Using the median WTP for lakefront and nonlakefront residents, we found that the increase in homeowner association fees would generate approximately $43,000, enough money to lease sufficient water to reach the target higher lake level in a normal water year.

Angle-stable and compressed angle-stable locking for tibiotalocalcaneal arthrodesis with retrograde intramedullary nails. Biomechanical evaluation.

PubMed

Mückley, Thomas; Hoffmeier, Konrad; Klos, Kajetan; Petrovitch, Alexander; von Oldenburg, Geert; Hofmann, Gunther O

2008-03-01

Retrograde intramedullary nailing is an established procedure for tibiotalocalcaneal arthrodesis. The goal of this study was to evaluate the effects of angle-stable locking or compressed angle-stable locking on the initial stability of the nails and on the behavior of the constructs under cyclic loading conditions. Tibiotalocalcaneal arthrodesis was performed in fifteen third-generation synthetic bones and twenty-four fresh-frozen cadaver legs with use of retrograde intramedullary nailing with three different locking modes: a Stryker nail with compressed angle-stable locking, a Stryker nail with angle-stable locking, and a statically locked Biomet nail. Analyses were performed of the initial stability of the specimens (range of motion) and the laxity of the constructs (neutral zone) in dorsiflexion/plantar flexion, varus/valgus, and external rotation/internal rotation. Cyclic testing up to 100,000 cycles was also performed. The range of motion and the neutral zone in dorsiflexion/plantar flexion at specific cycle increments were determined. In both bone models, the intramedullary nails with compressed angle-stable locking and those with angle-stable locking were significantly superior, in terms of a smaller range of motion and neutral zone, to the statically locked nails. The compressed angle-stable nails were superior to the angle-stable nails only in the synthetic bone model, in external/internal rotation. Cyclic testing showed the nails with angle-stable locking and those with compressed angle-stable locking to have greater stability in both models. In the synthetic bone model, compressed angle-stable locking was significantly better than angle-stable locking; in the cadaver bone model, there was no significant difference between these two locking modes. During cyclic testing, five statically locked nails in the cadaver bone model failed, whereas one nail with angle-stable locking and one with compressed angle-stable locking failed. Regardless of the bone model, the nails with angle-stable or compressed angle-stable locking had better initial stability and better stability following cycling than did the nails with static locking.

Suppression of persistent photo-conductance in solution-processed amorphous oxide thin-film transistors

NASA Astrophysics Data System (ADS)

Lee, Minkyung; Kim, Minho; Jo, Jeong-Wan; Park, Sung Kyu; Kim, Yong-Hoon

2018-01-01

This study offers a combinatorial approach for suppressing the persistent photo-conductance (PPC) characteristic in solution-processed amorphous oxide semiconductor (AOS) thin-film transistors (TFTs) in order to achieve rapid photo-recovery. Various analyses were used to examine the photo-instability of indium-gallium-zinc-oxide (IGZO) TFTs including negative-bias-illumination-stress (NBIS) and transient photo-response behaviors. It was found that the indium ratio in metallic components had a significant impact on their PPC and photo-recovery characteristics. In particular, when the indium ratio was low (51.5%), the PPC characteristic was significantly suppressed and achieving rapid photo-recovery was possible without significantly affecting the electrical performance of AOSs. These results imply that the optimization of the indium composition ratio may allow achieving highly photo-stable and near PPC-free characteristics while maintaining high electrical performance of AOSs. It is considered that the negligible PPC behavior and rapid photo-recovery observed in IGZO TFTs with a lower indium composition are attributed to the less activation energy required for the neutralization of ionized oxygen vacancies.

Production of biohythane from food waste via an integrated system of continuously stirred tank and anaerobic fixed bed reactors.

PubMed

Yeshanew, Martha M; Frunzo, Luigi; Pirozzi, Francesco; Lens, Piet N L; Esposito, Giovanni

2016-11-01

The continuous production of biohythane (mixture of biohydrogen and methane) from food waste using an integrated system of a continuously stirred tank reactor (CSTR) and anaerobic fixed bed reactor (AFBR) was carried out in this study. The system performance was evaluated for an operation period of 200days, by stepwise shortening the hydraulic retention time (HRT). An increasing trend of biohydrogen in the CSTR and methane production rate in the AFBR was observed regardless of the HRT shortening. The highest biohydrogen yield in the CSTR and methane yield in the AFBR were 115.2 (±5.3)L H2/kgVSadded and 334.7 (±18.6)L CH4/kgCODadded, respectively. The AFBR presented a stable operation and excellent performance, indicated by the increased methane production rate at each shortened HRT. Besides, recirculation of the AFBR effluent to the CSTR was effective in providing alkalinity, maintaining the pH in optimal ranges (5.0-5.3) for the hydrogen producing bacteria. Copyright © 2016 Elsevier Ltd. All rights reserved.

Nitrogen removal and intentional nitrous oxide production from reject water in a coupled nitritation/nitrous denitritation system under real feed-stream conditions.

PubMed

Weißbach, Max; Thiel, Paul; Drewes, Jörg E; Koch, Konrad

2018-05-01

A Coupled Aerobic-anoxic Nitrous Decomposition Operation (CANDO) was performed over five months to investigate the performance and dynamics of nitrogen elimination and nitrous oxide production from digester reject water under real feed-stream conditions. A 93% conversion of ammonium to nitrite could be maintained for adapted seed sludge in the first stage (nitritation). The second stage (nitrous denitritation), inoculated with conventional activated sludge, achieved a conversion of 70% of nitrite to nitrous oxide after only 12 cycles of operation. The development of an alternative feeding strategy and the addition of a coagulant (FeCl 3 ) facilitated stable operation and process intensification. Under steady-state conditions, nitrite was reliably eliminated and different nitrous oxide harvesting strategies were assessed. Applying continuous removal increased N 2 O yields by 16% compared to the application of a dedicated stripping phase. These results demonstrate the feasible application of the CANDO process for nitrogen removal and energy recovery from ammonia rich wastewater. Copyright © 2018 Elsevier Ltd. All rights reserved.

US Department of Energy Hybrid Electric Vehicle Battery and Fuel Economy Testing

NASA Astrophysics Data System (ADS)

Karner, Donald; Francfort, James

The advanced vehicle testing activity (AVTA), part of the US Department of Energy's FreedomCAR and Vehicle Technologies Program, has conducted testing of advanced technology vehicles since August 1995 in support of the AVTA goal to provide benchmark data for technology modelling, and research and development programs. The AVTA has tested over 200 advanced technology vehicles including full-size electric vehicles, urban electric vehicles, neighborhood electric vehicles, and internal combustion engine vehicles powered by hydrogen. Currently, the AVTA is conducting a significant evaluation of hybrid electric vehicles (HEVs) produced by major automotive manufacturers. The results are posted on the AVTA web page maintained by the Idaho National Laboratory. Through the course of this testing, the fuel economy of HEV fleets has been monitored and analyzed to determine the 'real world' performance of their hybrid energy systems, particularly the battery. The initial fuel economy of these vehicles has typically been less than that determined by the manufacturer and also varies significantly with environmental conditions. Nevertheless, the fuel economy and, therefore, battery performance, has remained stable over the life of a given vehicle (160 000 miles).

Microengineered Conductive Elastomeric Electrodes for Long-Term Electrophysiological Measurements with Consistent Impedance under Stretch

PubMed Central

Hu, Dinglong; Cheng, Tin Kei; Xie, Kai; Lam, Raymond H. W.

2015-01-01

In this research, we develop a micro-engineered conductive elastomeric electrode for measurements of human bio-potentials with the absence of conductive pastes. Mixing the biocompatible polydimethylsiloxane (PDMS) silicone with other biocompatible conductive nano-particles further provides the material with an electrical conductivity. We apply micro-replica mold casting for the micro-structures, which are arrays of micro-pillars embedded between two bulk conductive-PDMS layers. These micro-structures can reduce the micro-structural deformations along the direction of signal transmission; therefore the corresponding electrical impedance under the physical stretch by the movement of the human body can be maintained. Additionally, we conduct experiments to compare the electrical properties between the bulk conductive-PDMS material and the microengineered electrodes under stretch. We also demonstrate the working performance of these micro-engineered electrodes in the acquisition of the 12-lead electrocardiographs (ECG) of a healthy subject. Together, the presented gel-less microengineered electrodes can provide a more convenient and stable bio-potential measurement platform, making tele-medical care more achievable with reduced technical barriers for instrument installation performed by patients/users themselves. PMID:26512662

Evaluation of a direct injection nebulizer interface for flow injection analysis and high performance liquid chromatography with inductively coupled plasma-atomic emission spectroscopic detection

DOE Office of Scientific and Technical Information (OSTI.GOV)

LaFreniere, K.E.

A direct injection nebulizer (DIN) was designed, developed, and evaluated to determine its potential utilization as an effective interface for flow injection analysis (FIA) and high performance liquid chromatography (HPLC) coupled with inductively coupled plasma-atomic emission spectroscopic detection. The analytical figures of merit for the DIN when used as an interface for FIA-ICP-AES were found to be comparable to or better than those obtained with conventional pneumatic nebulization in terms of limits of detection (LODs), reproducibility, linearity, and interelement effects. Stable plasma operation was maintained for the DIN sample introduction of a variety of pure organic solvents, including acetonitrile, methanol,more » methylisobutylketone, and pyridine. The HPLC-DIN-ICP-AES facility was specifically applied for the speciation of inorganic and organometallic species contained in synthetic mixtures, vanilla extracts, and a variety of energy-related materials, such as shale oil process water, coal extracts, shale oil, crude oil, and an SRC II. Suggestions for future research are also considered. 227 refs., 44 figs., 15 tabs.« less

Na2.5Fe1.75(SO4)3/Ketjen/rGO: An advanced cathode composite for sodium ion batteries

NASA Astrophysics Data System (ADS)

Goñi, A.; Iturrondobeitia, A.; Gil de Muro, I.; Lezama, L.; Rojo, T.

2017-11-01

An advanced cathode composite Na2.5Fe1.75(SO4)3/Ketjen/rGO for sodium ion batteries has been prepared, joining together the excellent electrochemical properties of the three components: off stoichiometric iron sulfate alluaudite, Ketjen Black carbon and reduced graphene oxide (rGO). This electrode material has been exhaustively characterized by XRD, thermogravimetric analysis, Raman spectroscopy and SEM and TEM microscopy. The study has demonstrated that a high quality electrode material has been designed containing a porous sulfate core properly coated by interweaved rGO fibers and Ketjen Black nanoparticles. The electrochemical study has revealed an excellent performance providing specific capacities close to the theoretical one at 1C. Additionally, this composite has shown a very good rate capability and a great cycling stability for at least 200 cycles maintaining a coulombic efficiency of 96%. The post mortem analysis, which includes EPR and XPS measurements, has demonstrated that the carbonaceous coating on the composite generates a stable and protective SEI layer over the active material guaranteeing a successful performance during a long cycle life.

Performance Assessment of Model-Based Optimal Feedforward and Feedback Current Profile Control in NSTX-U using the TRANSP Code

NASA Astrophysics Data System (ADS)

Ilhan, Z.; Wehner, W. P.; Schuster, E.; Boyer, M. D.; Gates, D. A.; Gerhardt, S.; Menard, J.

2015-11-01

Active control of the toroidal current density profile is crucial to achieve and maintain high-performance, MHD-stable plasma operation in NSTX-U. A first-principles-driven, control-oriented model describing the temporal evolution of the current profile has been proposed earlier by combining the magnetic diffusion equation with empirical correlations obtained at NSTX-U for the electron density, electron temperature, and non-inductive current drives. A feedforward + feedback control scheme for the requlation of the current profile is constructed by embedding the proposed nonlinear, physics-based model into the control design process. Firstly, nonlinear optimization techniques are used to design feedforward actuator trajectories that steer the plasma to a desired operating state with the objective of supporting the traditional trial-and-error experimental process of advanced scenario planning. Secondly, a feedback control algorithm to track a desired current profile evolution is developed with the goal of adding robustness to the overall control scheme. The effectiveness of the combined feedforward + feedback control algorithm for current profile regulation is tested in predictive simulations carried out in TRANSP. Supported by PPPL.

Sorbents with high efficiency for CO2 capture based on amines-supported carbon for biogas upgrading.

PubMed

Pino, Lidia; Italiano, Cristina; Vita, Antonio; Fabiano, Concetto; Recupero, Vincenzo

2016-10-01

Sorbents for CO 2 capture have been prepared by wet impregnation of a commercial active carbon (Ketjen-black, Akzo Nobel) with two CO 2 -philic compounds, polyethylenimine (PEI) and tetraethylenepentamine (TEPA), respectively. The effects of amine amount (from 10 to 70wt.%), CO 2 concentration in the feed, sorption temperature and gas hourly space velocity on the CO 2 capture performance have been investigated. The sorption capacity has been evaluated using the breakthrough method, with a fixed bed reactor equipped with on line gas chromatograph. The samples have been characterized by N 2 adsorption-desorption, scanning electron microscopy and energy dispersive X-ray (SEM/EDX). A promising CO 2 sorption capacity of 6.90 mmol/g sorbent has been obtained with 70wt.% of supported TEPA at 70°C under a stream containing 80vol% of CO 2 . Sorption tests, carried out with simulated biogas compositions (CH 4 /CO 2 mixtures), have revealed an appreciable CO 2 separation selectivity; stable performance was maintained for 20 adsorption-desorption cycles. Copyright © 2016. Published by Elsevier B.V.

Coevolution Maintains Diversity in the Stochastic "Kill the Winner" Model

NASA Astrophysics Data System (ADS)

Xue, Chi; Goldenfeld, Nigel

2017-12-01

The "kill the winner" hypothesis is an attempt to address the problem of diversity in biology. It argues that host-specific predators control the population of each prey, preventing a winner from emerging and thus maintaining the coexistence of all species in the system. We develop a stochastic model for the kill the winner paradigm and show that the stable coexistence state of the deterministic kill the winner model is destroyed by demographic stochasticity, through a cascade of extinction events. We formulate an individual-level stochastic model in which predator-prey coevolution promotes the high diversity of the ecosystem by generating a persistent population flux of species.

Spatiotemporal Object History Affects the Selection of Task-Relevant Properties

ERIC Educational Resources Information Center

Schreij, Daniel; Olivers, Christian N. L.

2013-01-01

For stable perception, we maintain mental representations of objects across space and time. What information is linked to such a representation? In this study, we extended our work showing that the spatiotemporal history of an object affects the way the object is attended the next time it is encountered. Observers conducted a visual search for a…

9 CFR 318.309 - Finished product inspection.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Incubation of shelf stable canned product—(i) Incubator. The establishment shall provide incubation... incubator. (ii) Incubation temperature. The incubation temperature shall be maintained at 95±5 °F (35±2.8 °C). If the incubation temperature falls below 90 °F (or 32 °C) or exceeds 100 °F (or 38 °C) but does not...

9 CFR 318.309 - Finished product inspection.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Incubation of shelf stable canned product—(i) Incubator. The establishment shall provide incubation... incubator. (ii) Incubation temperature. The incubation temperature shall be maintained at 95±5 °F (35±2.8 °C). If the incubation temperature falls below 90 °F (or 32 °C) or exceeds 100 °F (or 38 °C) but does not...

9 CFR 318.309 - Finished product inspection.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Incubation of shelf stable canned product—(i) Incubator. The establishment shall provide incubation... incubator. (ii) Incubation temperature. The incubation temperature shall be maintained at 95±5 °F (35±2.8 °C). If the incubation temperature falls below 90 °F (or 32 °C) or exceeds 100 °F (or 38 °C) but does not...

New insights into the amphibious life of Biomphalaria glabrata and susceptibility of its egg masses to fungal infection

USDA-ARS?s Scientific Manuscript database

Egg masses of an aquatic snail, Biomphalaria glabrata, matured, and juveniles subsequently eclosed and were mobile in a stable water film of transitory habitats simulated by two different simple test devices described here. The viability of eggs maintained in an unstable film due to low ambient mois...

Visual impacts in the urban-wildland interface

Treesearch

Arthur W. Magill; Rowan A. Rowntree; Robert O. Brush

1979-01-01

The urban-wildland interface is treated as a place where extremes meet--where it is difficult to maintain a visually appealing transition from country to city. Problems are identified in relation to stable cities, urbanizing areas, and developing resorts in the wildlands. The visual problems of urbanization are also discussed in relation to physical impacts such as...

Unmanned Air Vehicle -Version 1.0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fred Oppel, SNL 06134

2013-04-17

This package contains modules that model the mobility of systems such as helicopters and fixed wing flying in the air. This package currently models first order physics - basically a velocity integrator. UAV mobility uses an internal clock to maintain stable, high-fidelity simulations over large time steps This package depends on interface that reside in the Mobility package.

Non-Toxic, Non-Flammable, -80 C Phase Change Materials

NASA Technical Reports Server (NTRS)

Cutbirth, J. Michael

2013-01-01

The objective of this effort was to develop a non-toxic, non-flammable, -80 C phase change material (PCM) to be used in NASA's ICEPAC capsules for biological sample preservation in flight to and from Earth orbit. A temperature of about -68 C or lower is a critical temperature for maintaining stable cell, tissue, and cell fragment storage.

Will We All Be Portfolio Workers? Trends and Issues Alerts.

ERIC Educational Resources Information Center

Kerka, Sandra

The world of stable, long-term employment is coming to an end. Part-time, contingent, and contract workers now account for more than 35% of the U.S. work force. It has been suggested that individuals will become "portfolio workers" with "portfolio careers." Individuals will maintain portfolios of their skills, abilities, and achievements and will…

1965 Oregon timber harvest.

Treesearch

Brian R. Wall

1966-01-01

Oregon maintained its high level of timber harvest in 1965 with an output of 9.4 billion board feet. This was the first time since 1926 that production remained unchanged in 2 consecutive years. The harvest from private lands remained stable at 4 billion feet, or 43 percent of the total. Forest industry's cut declined 2 percent (83 million board feet) from 1964,...

Multi-saline sample distillation apparatus for hydrogen isotope analyses : design and accuracy

USGS Publications Warehouse

Hassan, Afifa Afifi

1981-01-01

A distillation apparatus for saline water samples was designed and tested. Six samples may be distilled simultaneously. The temperature was maintained at 400 C to ensure complete dehydration of the precipitating salts. Consequently, the error in the measured ratio of stable hydrogen isotopes resulting from incomplete dehydration of hydrated salts during distillation was eliminated. (USGS)

Control of root system architecture by DEEPER ROOTING 1 increases rice yield under drought conditions.

PubMed

Uga, Yusaku; Sugimoto, Kazuhiko; Ogawa, Satoshi; Rane, Jagadish; Ishitani, Manabu; Hara, Naho; Kitomi, Yuka; Inukai, Yoshiaki; Ono, Kazuko; Kanno, Noriko; Inoue, Haruhiko; Takehisa, Hinako; Motoyama, Ritsuko; Nagamura, Yoshiaki; Wu, Jianzhong; Matsumoto, Takashi; Takai, Toshiyuki; Okuno, Kazutoshi; Yano, Masahiro

2013-09-01

The genetic improvement of drought resistance is essential for stable and adequate crop production in drought-prone areas. Here we demonstrate that alteration of root system architecture improves drought avoidance through the cloning and characterization of DEEPER ROOTING 1 (DRO1), a rice quantitative trait locus controlling root growth angle. DRO1 is negatively regulated by auxin and is involved in cell elongation in the root tip that causes asymmetric root growth and downward bending of the root in response to gravity. Higher expression of DRO1 increases the root growth angle, whereby roots grow in a more downward direction. Introducing DRO1 into a shallow-rooting rice cultivar by backcrossing enabled the resulting line to avoid drought by increasing deep rooting, which maintained high yield performance under drought conditions relative to the recipient cultivar. Our experiments suggest that control of root system architecture will contribute to drought avoidance in crops.

Why People Play: Artificial Lives Acquiring Play Instinct to Stabilize Productivity

PubMed Central

Tamura, Shinichi; Inabayashi, Shoji; Hayakawa, Waichi; Yokouchi, Takahiro; Mitsumoto, Hiroshi; Taketani, Hisashi

2012-01-01

We propose a model to generate a group of artificial lives capable of coping with various environments which is equivalent to a set of requested task, and likely to show that the plays or hobbies are necessary for the group of individuals to maintain the coping capability with various changes of the environment as a whole. This may be an another side of saying that the wide variety of the abilities in the group is necessary, and if the variety in a species decreased, its species will be extinguished. Thus, we show some simulation results, for example, in the world where more variety of abilities are requested in the plays, performance of the whole world becomes stable and improved in spite of being calculated only from job tasks, and can avoid the risk of extinction of the species. This is the good effect of the play. PMID:23304120

Why people play: artificial lives acquiring play instinct to stabilize productivity.

PubMed

Tamura, Shinichi; Inabayashi, Shoji; Hayakawa, Waichi; Yokouchi, Takahiro; Mitsumoto, Hiroshi; Taketani, Hisashi

2012-01-01

We propose a model to generate a group of artificial lives capable of coping with various environments which is equivalent to a set of requested task, and likely to show that the plays or hobbies are necessary for the group of individuals to maintain the coping capability with various changes of the environment as a whole. This may be an another side of saying that the wide variety of the abilities in the group is necessary, and if the variety in a species decreased, its species will be extinguished. Thus, we show some simulation results, for example, in the world where more variety of abilities are requested in the plays, performance of the whole world becomes stable and improved in spite of being calculated only from job tasks, and can avoid the risk of extinction of the species. This is the good effect of the play.

On-chip supercapacitors with ultrahigh volumetric performance based on electrochemically co-deposited CuO/polypyrrole nanosheet arrays

NASA Astrophysics Data System (ADS)

Qian, Tao; Zhou, Jinqiu; Xu, Na; Yang, Tingzhou; Shen, Xiaowei; Liu, Xuejun; Wu, Shishan; Yan, Chenglin

2015-10-01

We introduce a new method for fabricating unique on-chip supercapacitors based on CuO/polypyrrole core/shell nanosheet arrays by means of direct electrochemical co-deposition on interdigital-like electrodes. The prepared all-solid-state device demonstrates exceptionally high specific capacitance of 1275.5 F cm-3 (˜40 times larger than that of CuO-only supercapacitors) and high-energy-density of 28.35 mWh cm-3, which are both significantly greater than other solid-state supercapacitors. More importantly, the device maintains approximately 100% capacity retention at 2.5 A cm-3 after 3000 cycles. The in situ co-deposition of CuO/polypyrrole nanosheets on interdigital substrate enables effective charge transport, electrode fabrication integrity, and device integration. Because of their high energy, power density, and stable cycling stability, these newly developed on-chip supercapacitors permit fast, reliable applications in portable and miniaturized electronic devices.

Monitoring scale scores over time via quality control charts, model-based approaches, and time series techniques.

PubMed

Lee, Yi-Hsuan; von Davier, Alina A

2013-07-01

Maintaining a stable score scale over time is critical for all standardized educational assessments. Traditional quality control tools and approaches for assessing scale drift either require special equating designs, or may be too time-consuming to be considered on a regular basis with an operational test that has a short time window between an administration and its score reporting. Thus, the traditional methods are not sufficient to catch unusual testing outcomes in a timely manner. This paper presents a new approach for score monitoring and assessment of scale drift. It involves quality control charts, model-based approaches, and time series techniques to accommodate the following needs of monitoring scale scores: continuous monitoring, adjustment of customary variations, identification of abrupt shifts, and assessment of autocorrelation. Performance of the methodologies is evaluated using manipulated data based on real responses from 71 administrations of a large-scale high-stakes language assessment.

Bayesian network analysis revealed the connectivity difference of the default mode network from the resting-state to task-state

PubMed Central

Wu, Xia; Yu, Xinyu; Yao, Li; Li, Rui

2014-01-01

Functional magnetic resonance imaging (fMRI) studies have converged to reveal the default mode network (DMN), a constellation of regions that display co-activation during resting-state but co-deactivation during attention-demanding tasks in the brain. Here, we employed a Bayesian network (BN) analysis method to construct a directed effective connectivity model of the DMN and compared the organizational architecture and interregional directed connections under both resting-state and task-state. The analysis results indicated that the DMN was consistently organized into two closely interacting subsystems in both resting-state and task-state. The directed connections between DMN regions, however, changed significantly from the resting-state to task-state condition. The results suggest that the DMN intrinsically maintains a relatively stable structure whether at rest or performing tasks but has different information processing mechanisms under varied states. PMID:25309414

Design of Instantaneous High Power Supply System with power distribution management for portable military devices

NASA Astrophysics Data System (ADS)

Kwak, Kiho; Kwak, Dongmin; Yoon, Joohong

2015-08-01

A design of an Instantaneous High Power Supply System (IHPSS) with a power distribution management (PDM) for portable military devices is newly addressed. The system includes a power board and a hybrid battery that can not only supply instantaneous high power but also maintain stable operation at critical low temperature (-30 °C). The power leakage and battery overcharge are effectively prevented by the optimal PDM. The performance of the proposed system under the required pulse loads and the operating conditions of a Korean Advanced Combat Rifle employed in the battlefield is modeled with simulations and verified experimentally. The system with the IHPSS charged the fuse setter with 1.7 times higher voltage (8.6 V) than the one without (5.4 V) under the pulse discharging rate (1 A at 0.5 duty, 1 ms) for 500 ms.

Power plant I - Fused salt

NASA Astrophysics Data System (ADS)

Roche, M.

A solar thermal power plant using fused salt as the heat transfer fluid for steam power generation is analyzed for the feasibility of economic operation. The salt is also stored in a tank reservoir for maintaining the primary heat loop at temperatures high enough for the salts to remain liquid, and also to provide reserve power for the steam generator. Initial studies were with eutectic (hitec) salt comprising Na, KOH, and nitrites melting at 146 C, and further studies were performed employing draw salt, which has no nitrite, is more stable at high temperature, and melts at 225 C. The use of draw salt was found to allow a 5 percent reduction in storage capacity. Further examinations of the effects of the hitec salts on corrosion and composition degradation at high temperatures are indicated. The molten salt system is projected to offer an efficiency of 26 percent.

Multi person detection and tracking based on hierarchical level-set method

NASA Astrophysics Data System (ADS)

Khraief, Chadia; Benzarti, Faouzi; Amiri, Hamid

2018-04-01

In this paper, we propose an efficient unsupervised method for mutli-person tracking based on hierarchical level-set approach. The proposed method uses both edge and region information in order to effectively detect objects. The persons are tracked on each frame of the sequence by minimizing an energy functional that combines color, texture and shape information. These features are enrolled in covariance matrix as region descriptor. The present method is fully automated without the need to manually specify the initial contour of Level-set. It is based on combined person detection and background subtraction methods. The edge-based is employed to maintain a stable evolution, guide the segmentation towards apparent boundaries and inhibit regions fusion. The computational cost of level-set is reduced by using narrow band technique. Many experimental results are performed on challenging video sequences and show the effectiveness of the proposed method.

ITO Modification for Efficient Inverted Organic Solar Cells.

PubMed

Susarova, Diana K; Akkuratov, Alexander V; Kukharenko, Andrey I; Cholakh, Seif O; Kurmaev, Ernst Z; Troshin, Pavel A

2017-10-03

We demonstrate a facile approach to designing transparent electron-collecting electrodes by depositing thin layers of medium and low work function metals on top of transparent conductive metal oxides (TCOs) such as ITO and FTO. The modified electrodes were fairly stable for months under ambient conditions and maintained their electrical characteristics. XPS spectroscopy data strongly suggested integration of the deposited metal in the TCO structure resulting in additional doping of the conducting oxide at the interface. Kelvin probe microscopy measurements revealed a significant decrease in the ITO work function after modification. Organic solar cells based on three different conjugated polymers have demonstrated state of the art performances in inverted device geometry using Mg- or Yb-modified ITO as electron collecting electrode. The simplicity of the proposed approach and the excellent ambient stability of the modified ITO electrodes allows one to expect their wide utilization in research laboratories and electronic industry.

Osteo-odonto keratoprosthesis in Stevens-Johnson syndrome: a case report.

PubMed

Sc, Reddy; I, Tajunisah; T, Tan D

2011-01-01

To report a successful osteo-odonto keratoprosthesis (OOKP) procedure in a case of end stage of corneal blindness due to Stevens-Johnson syndrome (SJS). An interventional case report. We describe a 35-year-old Indian woman, a known case of SJS with bilateral dry eyes and corneal blindness (failed corneal graft with vascularised total corneal opacity in the right eye and non-healing corneal ulcer in the left eye). Vision was hand movement only in both eyes. The corneal ulcer healed with medical treatment resulting in vascularised total corneal opacity with no improvement in vision. OOKP was performed in the right eye and the vision was improved from hand movement to 6/6. The same vision was maintained in the right eye at the last follow-up 5 years after surgery. OOKP provides good visual rehabilitation with long-term anatomically stable prosthesis in patients with end-stage of ocular surface disorders and corneal blindness secondary to SJS.

Current Development in Treatment and Hydrogen Energy Conversion of Organic Solid Waste

NASA Astrophysics Data System (ADS)

Shin, Hang-Sik

2008-02-01

This manuscript summarized current developments on continuous hydrogen production technologies researched in Korea advanced institute of science and technology (KAIST). Long-term continuous pilot-scale operation of hydrogen producing processes fed with non-sterile food waste exhibited successful results. Experimental findings obtained by the optimization processes of growth environments for hydrogen producing bacteria, the development of high-rate hydrogen producing strategies, and the feasibility tests for real field application could contribute to the progress of fermentative hydrogen production technologies. Three major technologies such as controlling dilution rate depending on the progress of acidogenesis, maintaining solid retention time independently from hydraulic retention time, and decreasing hydrogen partial pressure by carbon dioxide sparging could enhance hydrogen production using anaerobic leaching beds reactors and anaerobic sequencing batch reactors. These findings could contribute to stable, reliable and effective performances of pilot-scale reactors treating organic wastes.

Interfacial stability of ultrathin films of magnetite Fe3O4 (111) on Al2O3(001) grown by ozone-assisted molecular-beam epitaxy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hong, Hawoong; Kim, Jongjin; Fang, Xinyue

Thin films of iron oxides including magnetite (Fe3O4) and hematite (α-Fe2O3) have many important applications. Both forms of oxide can occur naturally during film growth by iron deposition under various oxidation environment; an important issue is to understand and control the process resulting in a single-phase film. We have performed in-situ real-time studies using x-ray diffraction of such film growth on sapphire (001) under pure ozone by monitoring the (00L) rod. Stable magnetite growth can be maintained at growth temperatures below 600° C up to a certain critical film thickness, beyond which the growth becomes hematite. The results demonstrate themore » importance of interfacial interaction in stabilizing the magnetite phase.« less

On-chip supercapacitors with ultrahigh volumetric performance based on electrochemically co-deposited CuO/polypyrrole nanosheet arrays.

PubMed

Qian, Tao; Zhou, Jinqiu; Xu, Na; Yang, Tingzhou; Shen, Xiaowei; Liu, Xuejun; Wu, Shishan; Yan, Chenglin

2015-10-23

We introduce a new method for fabricating unique on-chip supercapacitors based on CuO/polypyrrole core/shell nanosheet arrays by means of direct electrochemical co-deposition on interdigital-like electrodes. The prepared all-solid-state device demonstrates exceptionally high specific capacitance of 1275.5 F cm(-3) (∼40 times larger than that of CuO-only supercapacitors) and high-energy-density of 28.35 mWh cm(-3), which are both significantly greater than other solid-state supercapacitors. More importantly, the device maintains approximately 100% capacity retention at 2.5 A cm(-3) after 3000 cycles. The in situ co-deposition of CuO/polypyrrole nanosheets on interdigital substrate enables effective charge transport, electrode fabrication integrity, and device integration. Because of their high energy, power density, and stable cycling stability, these newly developed on-chip supercapacitors permit fast, reliable applications in portable and miniaturized electronic devices.

The Adult Drosophila Malpighian Tubules Are Maintained by Pluripotent Stem Cells

PubMed Central

Singh, Shree Ram; Liu, Wei; Hou, Steven X.

2007-01-01

Summary All animals must excrete the waste products of metabolism. Excretion is performed by the kidney in vertebrates and by the Malpighian tubules in Drosophila. The mammalian kidney has an inherent ability for recovery and regeneration following ischemic injury. Stem cells and progenitor cells have been proposed to be responsible for repair and regeneration of injured renal tissue. In Drosophila, the Malpighian tubules are thought to be very stable, and no stem cells have been identified. We have identified pluripotent stem cells in the region of lower tubules and ureters of the Malpighian tubules. Using lineage tracing and molecular marker labeling, we demonstrated that several differentiated cells in the Malpighian tubules arise from the stem cells and an autocrine JAK-STAT signaling regulates the stem cells' self-renewal. Identifying adult kidney stem cells in Drosophila may provide important clues for understanding mammalian kidney repair and regeneration during injury. PMID:18371350

Protective role of salt in catalysis and maintaining structure of halophilic proteins against denaturation.

PubMed

Sinha, Rajeshwari; Khare, Sunil K

2014-01-01

Search for new industrial enzymes having novel properties continues to be a desirable pursuit in enzyme research. The halophilic organisms inhabiting under saline/ hypersaline conditions are considered as promising source of useful enzymes. Their enzymes are structurally adapted to perform efficient catalysis under saline environment wherein n0n-halophilic enzymes often lose their structure and activity. Haloenzymes have been documented to be polyextremophilic and withstand high temperature, pH, organic solvents, and chaotropic agents. However, this stability is modulated by salt. Although vast amount of information have been generated on salt mediated protection and structure function relationship in halophilic proteins, their clear understanding and correct perspective still remain incoherent. Furthermore, understanding their protein architecture may give better clue for engineering stable enzymes which can withstand harsh industrial conditions. The article encompasses the current level of understanding about haloadaptations and analyzes structural basis of their enzyme stability against classical denaturants.

Protective role of salt in catalysis and maintaining structure of halophilic proteins against denaturation

PubMed Central

Sinha, Rajeshwari; Khare, Sunil K.

2014-01-01

Search for new industrial enzymes having novel properties continues to be a desirable pursuit in enzyme research. The halophilic organisms inhabiting under saline/ hypersaline conditions are considered as promising source of useful enzymes. Their enzymes are structurally adapted to perform efficient catalysis under saline environment wherein n0n-halophilic enzymes often lose their structure and activity. Haloenzymes have been documented to be polyextremophilic and withstand high temperature, pH, organic solvents, and chaotropic agents. However, this stability is modulated by salt. Although vast amount of information have been generated on salt mediated protection and structure function relationship in halophilic proteins, their clear understanding and correct perspective still remain incoherent. Furthermore, understanding their protein architecture may give better clue for engineering stable enzymes which can withstand harsh industrial conditions. The article encompasses the current level of understanding about haloadaptations and analyzes structural basis of their enzyme stability against classical denaturants. PMID:24782853

The evolution of CELSS for lunar bases. [Controlled Ecological Life Support Systems

NASA Technical Reports Server (NTRS)

Macelroy, R. D.; Klein, H. P.; Averner, M. M.

1985-01-01

A bioregenerative life support system designed to address the fundamental requirements of a functioning independent lunar base is presented in full. Issues to be discussed are associated with CELSS weight, volume and cost of operation. The fundamental CELSS component is a small, highly automated module containing plants which photosynthesize and provide the crew with food, water and oxygen. Hydrogen, nitrogen and carbon dioxide will be initially brought in from earth, recycled and their waste products conserved. As the insufficiency of buffers necessitates stringent cybernetic control, a stable state will be maintained by computer control. Through genetic engineering and carbon dioxide, temperature, and nutrient manipulation, plant productivity can be increased, while the area necessary for growth and illumination energy decreased. In addition, photosynthetic efficiency can be enhanced through lamp design, fiber optics and the use of appropriate wavelengths. Crop maintenance will be performed by robotics, as a means of preventing plant ailments.

Once-Monthly Continuous Erythropoietin Receptor Activator (C.E.R.A.) in Patients with Hemodialysis-Dependent Chronic Kidney Disease: Pooled Data from Phase III Trials.

PubMed

Locatelli, Francesco; Choukroun, Gabriel; Truman, Matt; Wiggenhauser, Alfons; Fliser, Danilo

2016-04-01

Erythropoiesis-stimulating agents and iron are commonly used in patients with chronic kidney disease with the aim of correcting anemia and maintaining stable hemoglobin levels. We analyzed pooled data from 13 studies with similar designs included in the Umbrella Continuous Erythropoietin Receptor Activator (C.E.R.A.) program to investigate the effects of continuous erythropoiesis receptor activator in clinically relevant subgroups of patients with chronic kidney disease and to determine whether the efficacy and safety outcomes demonstrated in the overall chronic kidney disease population are maintained in specific subgroups. Data from 13 Phase III trials set up with similar design were retrospectively pooled for this analysis. Patients with chronic kidney disease who had previously been receiving epoetin or darbepoetin were switched to continuous erythropoiesis receptor activator once-monthly after a 4- to 8-week screening period. Patients entered a 16-week continuous erythropoiesis receptor activator dose-titration period followed by an 8-week evaluation period. In total, 2060 patients were included in the analysis. Subgroups were defined based on: hemoglobin target range [lower (10.0-12.0 g/dL)/upper (10.5-13.0 g/dL)], gender (female/male), age (<65/≥65), baseline N-terminal pro-B-type natriuretic peptide levels (<5000/≥5000), cardiovascular risk factors (diabetes/cardiac/vascular/none). Across all subgroups analyzed, switching from shorter-acting erythropoiesis-stimulating agents to continuous erythropoiesis receptor activator once-monthly maintained stable hemoglobin concentrations in a high proportion of patients (78%), with only moderate hemoglobin fluctuations and a low number of dose changes. The safety profile across subgroups was as expected based on pre-existing risk factors; observed increases in adverse events were attributable to underlying risk factors rather than study drug. This retrospective analysis of 13 trials showed that continuous erythropoiesis receptor activator once-monthly maintained stable hemoglobin levels across a number of clinically relevant patient subgroups, including those with higher inherent cardiovascular risk. The safety profile was consistent with that previously established in the chronic kidney disease population. CLINICALTRIALS. NCT00413894/NCT00545571/NCT00517413/NCT00560404/NCT00882713/NCT00550680/NCT00576303/NCT00660023/NCT00717821/NCT00642850/NCT00605293/NCT00661505/NCT00699348. F. Hoffmann-La Roche Ltd, Basel, Switzerland.

On the status of IAEA delta-13C stable isotope reference materials.

NASA Astrophysics Data System (ADS)

Assonov, Sergey; Groening, Manfred; Fajgelj, Ales

2016-04-01

For practical reasons all isotope measurements are performed on relative scales realized through the use of international, scale-defining primary standards. In fact these standards were materials (artefacts, similar to prototypes of meter and kg) selected based on their properties. The VPDB delta-13C scale is realised via two highest-level reference materials NBS19 and LSVEC, the first defining the scale and the second aimed to normalise lab-to-lab calibrations. These two reference materials (RMs) have been maintained and distributed by IAEA and NIST. The priority task is to maintain these primary RMs at the required uncertainty level, thus ensuring the long-term scale consistency. The second task is to introduce replacements when needed (currently for exhausted NBS19, work in progress). The next is to produce a family of lower level RMs (secondary, tertiary) addressing needs of various applications (with different delta values, in different physical-chemical forms) and their needs for the uncertainty; these RMs should be traceable to the highest level RMs. Presently three is a need for a range of RMs addressing existing and newly emerging analytical techniques (e.g. optical isotopic analysers) in form of calibrated CO2 gases with different delta-13C values. All that implies creating a family of delta-13C stable isotope reference materials. Presently IAEA works on replacement for NBS19 and planning new RMs. Besides, we found that LSVEC (introduced as second anchor for the VPDB scale in 2006) demonstrate a considerable scatter of its delta-13C value which implies a potential bias of the property value and increased value uncertainty which may conflict with uncertainty requirements for atmospheric monitoring. That is not compatible with the status of LSVEC, and therefore it should be replaced as soon as possible. The presentation will give an overview of the current status, the strategic plan of developments and the near future steps.

Internal combustion engine control for series hybrid electric vehicles by parallel and distributed genetic programming/multiobjective genetic algorithms

NASA Astrophysics Data System (ADS)

Gladwin, D.; Stewart, P.; Stewart, J.

2011-02-01

This article addresses the problem of maintaining a stable rectified DC output from the three-phase AC generator in a series-hybrid vehicle powertrain. The series-hybrid prime power source generally comprises an internal combustion (IC) engine driving a three-phase permanent magnet generator whose output is rectified to DC. A recent development has been to control the engine/generator combination by an electronically actuated throttle. This system can be represented as a nonlinear system with significant time delay. Previously, voltage control of the generator output has been achieved by model predictive methods such as the Smith Predictor. These methods rely on the incorporation of an accurate system model and time delay into the control algorithm, with a consequent increase in computational complexity in the real-time controller, and as a necessity relies to some extent on the accuracy of the models. Two complementary performance objectives exist for the control system. Firstly, to maintain the IC engine at its optimal operating point, and secondly, to supply a stable DC supply to the traction drive inverters. Achievement of these goals minimises the transient energy storage requirements at the DC link, with a consequent reduction in both weight and cost. These objectives imply constant velocity operation of the IC engine under external load disturbances and changes in both operating conditions and vehicle speed set-points. In order to achieve these objectives, and reduce the complexity of implementation, in this article a controller is designed by the use of Genetic Programming methods in the Simulink modelling environment, with the aim of obtaining a relatively simple controller for the time-delay system which does not rely on the implementation of real time system models or time delay approximations in the controller. A methodology is presented to utilise the miriad of existing control blocks in the Simulink libraries to automatically evolve optimal control structures.

Stability of Extemporaneously Compounded Dexamethasone in Glass and Plastic Bottles and Plastic Syringes

PubMed Central

Ensom, Mary H H; Décarie, Diane

2014-01-01

Background Dexamethasone is widely used to treat rheumatic and endocrine disorders and chemotherapy-induced nausea and vomiting. A palatable, alcohol-free liquid formulation, with a suitable concentration to allow reasonable administration volume, is available only via extemporaneous compounding. Objective: To evaluate the stability of dexamethasone suspensions in commercially available vehicles (Oral Mix and Oral Mix SF) in various types of containers after storage at 25°C and 4°C for up to 91 days. Methods: Dexamethasone suspensions (1 mg/mL) were prepared in Oral Mix and Oral Mix SF and then transferred to amber glass and plastic prescription bottles and plastic oral syringes. Suspensions in all 3 types of containers were stored at 25°C; suspensions in glass and plastic bottles were also stored at 4°C. Samples were collected weekly from each container up to 28 days and then every 2 weeks up to 91 days. The samples were analyzed by a validated, stability-indicating high-performance liquid chromatography − ultraviolet detection method. A suspension was considered stable if it maintained at least 90% of its initial dexamethasone concentration. Changes in colour, taste, odour, precipitation (and ease of resuspension), and pH were used to assess physical compatibility. Results: All suspensions maintained at least 96% of the original concentration for up to 91 days with storage at 25°C or at 4°C. No notable changes in colour, taste, odour, precipitation, or pH were observed over the 91-day period. Conclusion: Dexamethasone suspensions (1 mg/mL) in Oral Mix and Oral Mix SF, stored in amber glass or plastic bottles or plastic syringes at 25°C or in amber glass or plastic bottles at 4°C can be expected to remain stable for up to 91 days. PMID:25214658

Stability of Levothyroxine in Sodium Chloride for IV Administration.

PubMed

Strong, Dawn K; Decarie, Diane; Ensom, Mary H H

2010-11-01

Levothyroxine by IV administration is often prescribed in the intensive care unit for the management of potential solid organ donors, following declaration of brain death and provision of consent for organ donation. Published data on the stability of levothyroxine in IV solutions are limited. To evaluate the physical compatibility and chemical stability, over a 24-h period, of 2 concentrations of levothyroxine in 0.9% sodium chloride with storage at room temperature and with exposure to or protection from light. Levothyroxine solutions (0.4 μg/mL and 2.0 μg/mL) were prepared in 50-mL minibags of 0.9% NaCl and stored at room temperature (25°C) with exposure to or protection from light. Samples were collected from each minibag at time 0 and after 0.5, 1.0, 1.5, 2.0, 3.0, 4.0, 8.0, 12.0, and 24.0 h. The samples were analyzed in triplicate with a validated stability-indicating high-performance liquid chromatography method using ultraviolet detection. A solution was considered stable if it maintained 90% of its initial concentration of levothyroxine. Changes in colour, clarity, and pH were assessed to determine the physical compatibility of the solutions. All samples remained clear, colourless, and free of precipitate throughout the study, and there were no significant changes in pH. Based on the 95% confidence interval of the slope of the curve relating concentration to time determined by linear regression, solutions of levothyroxine with concentration 0.4 μg/mL would maintain at least 90% of the initial concentration for 16.9 h with exposure to light and for 18.0 h if kept in the dark. Solutions of levothyroxine with concentration 2.0 μg/mL would maintain at least 90% of the initial concentration for 6.5 h with exposure to light and for 12.0 h if kept in the dark, with 95% confidence. Extemporaneously prepared solutions of levothyroxine in 0.9% NaCl can be expected to remain stable for at least 6.5 h if stored without protection from light and at least 12 h if stored in the dark. Stability is related to concentration, with more dilute solutions having greater stability.

Impact of pretransplant renal function on survival after liver transplantation.

PubMed

Gonwa, T A; Klintmalm, G B; Levy, M; Jennings, L S; Goldstein, R M; Husberg, B S

1995-02-15

To determine the effect of pretransplant liver function on survival following orthotopic liver transplantation and to quantify the effects of cyclosporine administration on long-term renal function in patients undergoing liver transplant, we performed an analysis of a prospectively maintained database. Data from 569 consecutive patients undergoing liver transplantation alone who were treated with CsA for immunosuppression were used for this study. Actuarial graft and patient survival rates were calculated using Kaplan-Meier statistics. Glomerular filtration rates, serum creatinine, and the use of various immunosuppressives were analyzed for this study. The initial analysis demonstrated that patients presenting for liver transplant with hepatorenal syndrome have a significantly decreased acturial patient survival after liver transplant at 5 years compared with patients without hepatorenal syndrome (60% vs. 68%, P < 0.03). Patients with hepatorenal syndrome recovered their renal function after liver transplant. Patients who had hepatorenal syndrome were sicker and required longer stays in the intensive care unit, longer hospitalizations, and more dialysis treatments after transplantation compared with patients who did not have hepatorenal syndrome. The incidence of end-stage renal disease after liver transplantation in patients who had hepatorenal syndrome was 7%, compared with 2% in patients who did not have hepatorenal syndrome. To more fully examine the effect of pretransplant renal function on posttransplant survival, the non-hepatorenal syndrome patients were divided into quartiles depending upon their pretransplant renal function. The patients with the lowest pretransplant renal function had the same survival as the patients with the highest pretransplant renal function. In addition, there was no increased incidence of acute or chronic rejection in any of the groups. The patients with the lower pretransplant renal function were treated with more azathioprine to maintain renal function and had a negligible decrease in glomerular filtration rate following transplant. Conversely, patients with the highest level of renal function pretransplant had a 40% decline in renal function in the first year, but maintained stable renal function up to 4 years after transplant. We conclude that pretransplant renal function other than hepato-renal syndrome has no effect on patient survival after orthotopic liver transplant. Renal function after liver transplant is stable after an initial decline, despite continued administration of CsA.(ABSTRACT TRUNCATED AT 400 WORDS)

Comparison of different cooling regimes within a shortened liquid cooling/warming garment on physiological and psychological comfort during exercise

NASA Technical Reports Server (NTRS)

Leon, Gloria R.; Koscheyev, Victor S.; Coca, Aitor; List, Nathan

2004-01-01

The aim of this study was to compare the effectiveness of different cooling regime intensities to maintain physiological and subjective comfort during physical exertion levels comparable to that engaged in during extravehicular activities (EVA) in space. We studied eight subjects (six males, two females) donned in our newly developed physiologically based shortened liquid cooling/warming garment (SLCWG). Rigorous (condition 1) and mild (condition 2) water temperature cooling regimes were compared at physical exertion levels comparable to that performed during EVA to ascertain the effectiveness of a lesser intensity of cooling in maintaining thermal comfort, thus reducing energy consumption in the portable life support system. Exercise intensity was varied across stages of the session. Finger temperature, rectal temperature, and subjective perception of overall body and hand comfort were assessed. Finger temperature was significantly higher in the rigorous cooling condition and showed a consistent increase across exercise stages, likely due to the restriction of heat extraction because of the intensive cold. In the mild cooling condition, finger temperature exhibited an overall decline with cooling, indicating greater heat extraction from the body. Rectal temperature was not significantly different between conditions, and showed a steady increase over exercise stages in both rigorous and mild cooling conditions. Ratings of overall comfort were 30% higher (more positive) and more stable in mild cooling (p<0.001). The mild cooling regime was more effective than rigorous cooling in allowing the process of heat exchange to occur, thus maintaining thermal homeostasis and subjective comfort during physical exertion.

Nonlinear dynamics analysis of a low-temperature-differential kinematic Stirling heat engine

NASA Astrophysics Data System (ADS)

Izumida, Yuki

2018-03-01

The low-temperature-differential (LTD) Stirling heat engine technology constitutes one of the important sustainable energy technologies. The basic question of how the rotational motion of the LTD Stirling heat engine is maintained or lost based on the temperature difference is thus a practically and physically important problem that needs to be clearly understood. Here, we approach this problem by proposing and investigating a minimal nonlinear dynamic model of an LTD kinematic Stirling heat engine. Our model is described as a driven nonlinear pendulum where the motive force is the temperature difference. The rotational state and the stationary state of the engine are described as a stable limit cycle and a stable fixed point of the dynamical equations, respectively. These two states coexist under a sufficient temperature difference, whereas the stable limit cycle does not exist under a temperature difference that is too small. Using a nonlinear bifurcation analysis, we show that the disappearance of the stable limit cycle occurs via a homoclinic bifurcation, with the temperature difference being the bifurcation parameter.

Group living in squamate reptiles: a review of evidence for stable aggregations.

PubMed

Gardner, Michael G; Pearson, Sarah K; Johnston, Gregory R; Schwarz, Michael P

2016-11-01

How sociality evolves and is maintained remains a key question in evolutionary biology. Most studies to date have focused on insects, birds, and mammals but data from a wider range of taxonomic groups are essential to identify general patterns and processes. The extent of social behaviour among squamate reptiles is under-appreciated, yet they are a promising group for further studies. Living in aggregations is posited as an important step in the evolution of more complex sociality. We review data on aggregations among squamates and find evidence for some form of aggregations in 94 species across 22 families. Of these, 18 species across 7 families exhibited 'stable' aggregations that entail overlapping home ranges and stable membership in long-term (years) or seasonal aggregations. Phylogenetic analysis suggests that stable aggregations have evolved multiple times in squamates. We: (i) identify significant gaps in our understanding; (ii) outline key traits which should be the focus of future research; and (iii) outline the potential for utilising reproductive skew theory to provide insights into squamate sociality. © 2015 Cambridge Philosophical Society.

Effect of surface stability on core muscle activity for dynamic resistance exercises.

PubMed

Willardson, Jeffrey M; Fontana, Fabio E; Bressel, Eadric

2009-03-01

To compare core muscle activity during resistance exercises performed on stable ground vs. the BOSU Balance Trainer. Twelve trained men performed the back squat, dead lift, overhead press, and curl lifts. The activity of the rectus abdominis, external oblique abdominis, transversus abdominis/internal oblique abdominis, and erector spinae muscles was assessed. Subjects performed each lift under three separate conditions including standing on stable ground with 50% of a 1-RM, standing on a BOSU Balance Trainer with 50% of a 1-RM, and standing on stable ground with 75% of a 1-RM. Significant differences were noted between the stable 75% of 1-RM and BOSU 50% of 1-RM conditions for the rectus abdominis during the overhead press and transversus abdominis/internal oblique abdominis during the overhead press and curl (P < .05). Conversely, there were no significant differences between the stable 75% of 1-RM and BOSU 50% of 1-RM conditions for the external obliques and erector spinae across all lifts examined. Furthermore, there were no significant differences between the BOSU 50% of 1-RM and stable 50% of 1-RM conditions across all muscles and lifts examined. The current study did not demonstrate any advantage in utilizing the BOSU Balance Trainer. Therefore, fitness trainers should be advised that each of the aforementioned lifts can be performed while standing on stable ground without losing the potential core muscle training benefits.

Effect of a High-Fructose Weight-Maintaining Diet on Lipogenesis and Liver Fat

PubMed Central

Noworolski, Susan M.; Wen, Michael J.; Dyachenko, Artem; Prior, Jessica L.; Weinberg, Melissa E.; Herraiz, Laurie A.; Tai, Viva W.; Bergeron, Nathalie; Bersot, Thomas P.; Rao, Madhu N.; Schambelan, Morris; Mulligan, Kathleen

2015-01-01

Context: Consumption of high-fructose diets promotes hepatic fatty acid synthesis (de novo lipogenesis [DNL]) and an atherogenic lipid profile. It is unclear whether these effects occur independent of positive energy balance and weight gain. Objectives: We compared the effects of a high-fructose, (25% of energy content) weight-maintaining diet to those of an isocaloric diet with the same macronutrient distribution but in which complex carbohydrate (CCHO) was substituted for fructose. Design, Setting, and Participants: Eight healthy men were studied as inpatients for consecutive 9-day periods. Stable isotope tracers were used to measure fractional hepatic DNL and endogenous glucose production (EGP) and its suppression during a euglycemic-hyperinsulinemic clamp. Liver fat was measured by magnetic resonance spectroscopy. Results: Weight remained stable. Regardless of the order in which the diets were fed, the high-fructose diet was associated with both higher DNL (average, 18.6 ± 1.4% vs 11.0 ± 1.4% for CCHO; P = .001) and higher liver fat (median, +137% of CCHO; P = .016) in all participants. Fasting EGP and insulin-mediated glucose disposal did not differ significantly, but EGP during hyperinsulinemia was greater (0.60 ± 0.07 vs 0.46 ± 0.06 mg/kg/min; P = .013) with the high-fructose diet, suggesting blunted suppression of EGP. Conclusion: Short-term high-fructose intake was associated with increased DNL and liver fat in healthy men fed weight-maintaining diets. PMID:25825943

Seven Ventilators Challenged With Leaks During Neonatal Nasal CPAP: An Experimental Pilot Study.

PubMed

Drevhammar, Thomas; Nilsson, Kjell; Zetterström, Henrik; Jonsson, Baldvin

2015-07-01

Nasal CPAP is the most common respiratory support for neonates. Several factors are considered important for effective treatment, including leaks at the patient interface and the delivery of pressure-stable CPAP. Investigations of pressure stability during leaks should include both the change in the mean delivered CPAP and the pressure variation during each breath. The aim of this study was to examine the response of ventilators delivering nasal CPAP when challenged with leaks at the patient interface. Seven ventilators providing nasal CPAP at 4 cm H2O were challenged with leaks during simulated neonatal breathing. Leak was applied for 15 consecutive breaths at a constant level (1-4 L/min). The 2 aspects of pressure stability were evaluated by measuring the mean delivered CPAP and the amplitude of pressure swings before, during, and after leaks. The ability to maintain the delivered CPAP and the amplitude of pressure swings varied greatly among the 7 ventilators before, during, and after leaks. Four of the ventilators tested have built-in leak compensation. There was no simple relationship between maintaining delivered CPAP during leaks and providing CPAP with low pressure swing amplitude. Maintaining the delivered CPAP and providing this without pressure swings are 2 separate aspects of pressure stability, and investigations concerning the clinical importance of pressure stability should address both aspects. This study also shows that compensation for leaks does not necessarily provide pressure-stable CPAP. Copyright © 2015 by Daedalus Enterprises.

Bubble-free on-chip continuous-flow polymerase chain reaction: concept and application.

PubMed

Wu, Wenming; Kang, Kyung-Tae; Lee, Nae Yoon

2011-06-07

Bubble formation inside a microscale channel is a significant problem in general microfluidic experiments. The problem becomes especially crucial when performing a polymerase chain reaction (PCR) on a chip which is subject to repetitive temperature changes. In this paper, we propose a bubble-free sample injection scheme applicable for continuous-flow PCR inside a glass/PDMS hybrid microfluidic chip, and attempt to provide a theoretical basis concerning bubble formation and elimination. Highly viscous paraffin oil plugs are employed in both the anterior and posterior ends of a sample plug, completely encapsulating the sample and eliminating possible nucleation sites for bubbles. In this way, internal channel pressure is increased, and vaporization of the sample is prevented, suppressing bubble formation. Use of an oil plug in the posterior end of the sample plug aids in maintaining a stable flow of a sample at a constant rate inside a heated microchannel throughout the entire reaction, as compared to using an air plug. By adopting the proposed sample injection scheme, we demonstrate various practical applications. On-chip continuous-flow PCR is performed employing genomic DNA extracted from a clinical single hair root sample, and its D1S80 locus is successfully amplified. Also, chip reusability is assessed using a plasmid vector. A single chip is used up to 10 times repeatedly without being destroyed, maintaining almost equal intensities of the resulting amplicons after each run, ensuring the reliability and reproducibility of the proposed sample injection scheme. In addition, the use of a commercially-available and highly cost-effective hot plate as a potential candidate for the heating source is investigated.

Thermal protection for a self-sensing piezoelectric control system

NASA Astrophysics Data System (ADS)

Simmers, Garnett E., Jr.; Sodano, Henry A.; Park, Gyuhae; Inman, Daniel J.

2007-12-01

Piezoelectric materials exhibit high electromechanical coupling that allows them to both generate an electrical signal when strained and, conversely, to produce a strain under an applied electric field. This coupling has led to the use of these materials for a variety of sensing and actuation purposes. One unique application of these materials is their use as self-sensing actuators where both the sensing and actuation functions are performed by a single patch of material. Since the actuation and sensing voltages both exist simultaneously in the piezoelectric material, a specially designed electric circuit, referred to as a bridge circuit, is required to realize the concept. Configuration of the material in this manner is advantageous for control systems due to the enhanced stability associated when collocated control is applied. While certain advantages result from this type of system, precise equilibrium of the bridge circuit is required to achieve stability. This equilibrium is easy to achieve in theory, but difficult in practice due to the thermal dependence of the piezoelectric material's dielectric constant. This study will investigate a novel method of accounting for these changes through the use of thermal switches to passively adjust the bridge circuit and maintain a balanced state. The proposed concept will be theoretically modeled and simulated in a vibration control application to identify the thermal range for stability with and without the array of switches. It will be shown that, through the use of nine thermal switches, the stable operating range can be increased by 95 °C while maintaining vibration control performance.

Lack of supervision after residential cardiac rehabilitation increases cardiovascular risk factors.

PubMed

Berent, Robert; von Duvillard, Serge P; Auer, Johann; Sinzinger, Helmut; Schmid, Peter

2010-06-01

Cardiovascular rehabilitation (CR) is an important component of care for patients with cardiovascular disease (CVD) and has been well documented and promoted by various health organizations and position statements worldwide. The purpose of this study was to investigate whether patients readmitted to CR on average 16 months after their previous discharge, maintained the reduction in CVD risk factors, maintained or improved functional capacity, occurrence of adverse cardiovascular events, and possible modifications in prescribed medications. Five hundred and seventy patients (60+/-10 years) underwent cycle ergometry and blood sampling at the beginning, the end of 21+/-2 days of the previous CR, and again at readmission to CR. The CR consisted of cycling for 17+/-4 min at frequency of six times a week and daily walking for 45 min at 60-70% of the maximal individual heart rate. Blood total cholesterol, low-density lipoprotein-cholesterol, triglycerides, and body mass index decreased significantly during CR. Resting blood pressure, maximal performance (watts), maximal oxygen uptake, and heart rate recovery improved significantly in 1 min (P<0.001). At readmission, all traditional CVD risk factors increased significantly, although medication was unchanged and angiotensin-converting enzyme inhibitors were partly replaced by angiotensin II receptor antagonists. Exercise performance remained unchanged. At readmission, we observed an increase in CVD risk factors, although, physical fitness remained stable. Thus, failure of lifestyle modification after CR indicates the cause for concern. Reinforcement of home setting sessions of CR patients or other strategies to enhance long-term compliance to lifestyle changes could reduce the observed attrition in CR benefits.

The long-term effects of UV exclusion on the microbial composition and photosynthetic competence of bacteria in hot-spring microbial mats.

PubMed

Norris, Tracy B; McDermott, Timothy R; Castenholz, Richard W

2002-03-01

The primary objective of this study was to determine whether the long-term exclusion of ultraviolet (UV) radiation (UVR) from hot-spring microbial mats resulted in an alteration of microbial composition, such as a shift to more UV-sensitive species. Over a 1-3-month period, microbial mats in two alkaline geothermal streams in Yellowstone National Park were covered with filters that excluded or transmitted UVR. Over some, 25% transmission neutral density screens were also used. In the 40-47 degrees C range, there were no apparent changes in community composition during the summer with or without high or low UVR, as assessed by denaturing gradient gel electrophoresis (DGGE) profiles after polymerase chain reaction amplification of 16S-rRNA genes with general Bacteria and Cyanobacteria primers. Major bands were purified from the DGGE gels and sequenced. Only one of the cyanobacterial sequences matched known strains in the database; the others appear to be unique. Although the bacterial composition of these communities was apparently stable, surface layers of cyanobacteria protected from UVR were not as competent photosynthetically as those that had been maintained under UVR. This decrease in competence was expressed as a loss of the ability to perform at a maximum rate under full UVR plus visible irradiance. However, even +UV-maintained cyanobacteria performed better when UVR was excluded during the photosynthesis tests. It is probable that the large differences in photosynthetic competence observed reflect changes at the level of gene expression in the dominant species rather than changes in species composition.

No strategy is evolutionarily stable in the repeated prisoner's dilemma.

PubMed

Lorberbaum, J

1994-05-21

Following the influential work of Axelrod, the repeated Prisoner's Dilemma game has become the theoretical gold standard for understanding the evolution of co-operative behavior among unrelated individuals. Using the game, several authors have found that a reciprocal strategy known as Tit for Tat (TFT) has done quite well in a wide range of environments. TFT strategists start out co-operating and then do what the other player did on the previous move. Despite the success of TFT and similar strategies in experimental studies of the game, Boyd & Lorberbaum (1987, Nature, Lond. 327, 58) have shown that no pure strategy, including TFT, is evolutionarily stable in the sense that each can be invaded by the joint effect of two invading strategies when long-term interaction occurs in the repeated game and future moves are discounted. Farrell & Ware (1989, Theor. Popul. Biol. 36, 161) have since extended these results to include finite mixes of pure strategies as well. Here, it is proven that no strategy is evolutionarily stable when long-term relationships are maintained in the repeated Prisoner's Dilemma and future moves are discounted. Namely, it is shown each completely probabilistic strategy (i.e. one that both co-operates and defects with positive probability after every sequence of behavior) may be invaded by a single deviant strategy. This completes the proof started by Boyd and Lorberbaum and extended by Farrell and Ware. This paper goes on to prove that no reactive strategy with a memory restricted to the opponent's preceding move is evolutionarily stable when there is no discounting of future moves. This is true despite the success of a more forgiving variant of TFT called GTFT in a recent tournament among reactive strategies conducted by Nowak & Sigmund (1992, Nature 355, 250) where future moves were not discounted. GTFT, for example, may be invaded by a pair of reactive mutants. Since no strategy is evolutionarily stable when future moves are discounted in the repeated game, the restriction of strategy types to those actually maintained by mutation and phenotypic and environmental variability in natural populations may be the key to understanding the evolution of co-operation. However, the result presented here that the somewhat realistic reactive strategies are also not evolutionarily stable at least in the non-discounted game suggests something else may be going on. For one, the proof that no reactive strategy is evolutionarily stable ironically shows the robustness of TFT-like strategies.(ABSTRACT TRUNCATED AT 400 WORDS)

Conceptions of ability as stable and self-evaluative processes: a longitudinal examination.

PubMed

Pomerantz, E M; Saxon, J L

2001-01-01

It has generally been taken for granted that conceiving of ability as stable leads to negative self-evaluative processes, particularly in the face of failure. Yet, a close examination of the empirical findings suggests that the picture may be more complex. In this research, a three-wave longitudinal design spanning 12 months was employed. Older elementary school children (N = 932) indicated their conceptions of academic and social ability as stable to external forces and to internal forces. They also provided information about the importance they place on academic and social competence, their knowledge about academic and social performance, their preference for academic challenge, their perceptions of academic and social competence, and their attributions for academic and social performance. Children's grades in school and their acceptance by peers were obtained as indicators of performance. Over time, conceiving of ability as stable to external forces, particularly in the academic domain, appeared to heighten the importance placed on competence, performance knowledge, preference for challenge, perceptions of competence, and self-enhancing attributions. In contrast, conceptions of ability as stable to internal forces, particularly in the academic domain, appeared to be fostered by placing little importance on competence, a lack of performance knowledge, avoidance of challenge, negative perceptions of competence, self-deprecating attributions, and poor performance.

Coupling the Alkaline-Surfactant-Polymer Technology and the Gelation Technology to Maximize Oil Production

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malcolm Pitts; Jie Qi; Dan Wilson

2005-12-01

Gelation technologies have been developed to provide more efficient vertical sweep efficiencies for flooding naturally fractured oil reservoirs or reservoirs with different sand lenses with high permeability contrast. The field proven alkaline-surfactant-polymer technology economically recovers 15% to 25% OOIP more crude oil than waterflooding froin swept pore space of an oil reservoir. However, alkaline-surfactant-polymer technology is not amenable to naturally fractured reservoirs or reservoirs with high permeability contrast zones because much of injected solution bypasses target pore space containing oil. This work investigates whether combining these two technologies could broaden applicability of alkaline-surfactant-polymer flooding into these reservoirs. Fluid-fluid interaction withmore » different gel chemical compositions and alkaline-surfactant-polymer solution with pH values ranging from 9.2 to 12.9 have been tested. Aluminum-polyacrylamide gels are not stable to alkaline-surfactant-polymer solutions at any pH. Chromium-polyacrylamide gels with polymer to chromium ion ratios of 25 or greater were stable to alkaline-surfactant-polymer solutions if solution pH was 10.6 or less. When the polymer to chromium ion was 15 or less, chromium-polyacrylamide gels were stable to alkaline-surfactant-polymer solutions with pH values up to 12.9. Chromium-xanthan gum gels were stable to alkaline-surfactant-polymer solutions with pH values of 12.9 at the polymer to chromium ion ratios tested. Silicate-polyacrylamide, resorcinol-formaldehyde, and sulfomethylated resorcinol-formaldehyde gels were also stable to alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Iron-polyacrylamide gels were immediately destroyed when contacted with any of the alkaline-surfactant-polymer solutions with pH values ranging from 9.2 to 12.9. Gel solutions under dynamic conditions of linear corefloods showed similar stability to alkaline-surfactant-polymer solutions as in the fluid-fluid analyses with the exception of the xanthan gum-chromium acetate gels. Aluminum-polyacrylamide flowing gels are not stable to alkaline-surfactant-polymer solutions of either pH 10.5 or 12.9, either in linear corefloods or in dual separate radial core, common manifold corefloods. Chromium acetate-polyacrylamide flowing and rigid tonguing gels are stable to subsequent alkaline-surfactant-polymer solution injection. Rigid tonguing chromium acetate-polyacrylamide gels maintained permeability reduction better than flowing chromium acetate-polyacrylamide gels. Chromium acetate gels were stable to injection of alkaline-surfactant-polymer solutions at 72 F, 125 F and 175 F in linear corefloods. Chromium acetate-polyacrylamide gels maintained diversion capability after injection of an alkaline-surfactant-polymer solution in stacked; radial coreflood with a common well bore. Chromium acetate-polyacrylamide gel used to seal fractured core maintain fracture closure if followed by an alkaline-surfactant-polymer solution. Chromium acetate-xanthan gum rigid gels are not stable to subsequent alkaline-surfactant-polymer solution injection at 72, 125, and 175 F. Silicate-polyacrylamide gels are not stable with subsequent injection of either a pH 10.5 or a 12.9 alkaline-surfactant-polymer solution. Resorcinol-formaldehyde gels were stable to subsequent alkaline-surfactant-polymer solution injection. When evaluated in a dual core configuration, injected fluid flows into the core with the greatest effective permeability to the injected fluid. The same gel stability trends to subsequent alkaline-surfactant-polymer injected solution were observed. Aluminum citrate-polyacrylamide, resorcinol-formaldehyde, and the silicate-polyacrylamide gel systems did not produce significant incremental oil in linear corefloods. Both flowing and rigid tonguing chromium acetate-polyacrylamide gels and the xanthan gum-chromium acetate gel system produced incremental oil with the rigid tonguing gel producing the greatest amount. Higher oil recovery could have been due to higher differential pressures across cores. Aluminum citrate-polyacrylamide gels, chromium acetate-polyacrylamide gels, silicate-polymer, and chromium-xanthan guin gels did not alter an alkaline-surfactant-polymer solution's ability to produce incremental oil. Incremental oil was reduced with the resorcinol-formaldehyde gel system. Total waterflood plus chemical flood oil recovery sequence recoveries were generally similar.« less

Preparation of carbon-free TEM microgrids by metal sputtering.

PubMed

Janbroers, S; de Kruijff, T R; Xu, Q; Kooyman, P J; Zandbergen, H W

2009-08-01

A new method for preparing carbon-free, temperature-stable Transmission Electron Microscope (TEM) grids is presented. An 80% Au/20% Pd metal film is deposited onto a 'holey' microgrid carbon supported on standard mixed-mesh Au TEM grids. Subsequently, the carbon film is selectively removed using plasma cleaning. In this way, an all-metal TEM film is made containing the 'same' microgrid as the original carbon film. Although electron transparency of the foil is reduced significantly, the open areas for TEM inspection of material over these areas are maintained. The metal foil can be prepared with various thicknesses and ensures good electrical conductivity. The new Au/Pd grids are stable to at least 775K under vacuum conditions.

Engineering of a Stable Whole-Cell Biocatalyst Capable of (S)-Styrene Oxide Formation for Continuous Two-Liquid-Phase Applications

PubMed Central

Panke, Sven; de Lorenzo, Víctor; Kaiser, Arnë; Witholt, Bernard; Wubbolts, Marcel G.

1999-01-01

Recombinant strains of Pseudomonas putida KT2440 carrying genetic expression cassettes with xylene oxygenase- and styrene monooxygenase-encoding genes on their chromosomes could be induced in shaking-flask experiments to specific activities that rivaled those of multicopy-plasmid-based Escherichia coli recombinants. Such strains maintained the introduced styrene oxidation activity in continuous two-liquid-phase cultures for at least 100 generations, although at a lower level than in the shaking-flask experiments. The data suggest that placement of target genes on the chromosome might be a suitable route for the construction of segregationally stable and highly active whole-cell biocatalysts. PMID:10584030

Stable Satellite Orbits for Global Coverage of the Moon

NASA Technical Reports Server (NTRS)

Ely, Todd; Lieb, Erica

2006-01-01

A document proposes a constellation of spacecraft to be placed in orbit around the Moon to provide navigation and communication services with global coverage required for exploration of the Moon. There would be six spacecraft in inclined elliptical orbits: three in each of two orthogonal orbital planes, suggestive of a linked-chain configuration. The orbits have been chosen to (1) provide 99.999-percent global coverage for ten years and (2) to be stable under perturbation by Earth gravitation and solar-radiation pressure, so that no deterministic firing of thrusters would be needed to maintain the orbits. However, a minor amount of orbit control might be needed to correct for such unmodeled effects as outgassing of the spacecraft.

Survival and reversion of a stable L form in soil

NASA Technical Reports Server (NTRS)

Horwitz, A. H.; Casida, L. E., Jr.

1978-01-01

The stable L form of Agromyces ramosus reverted to a bacterial form when incubated in sterilized soil. The cellular and colonial morphology of this bacterial form resembled that of the original parent bacterial form. The two forms differed, however, in that the revertant maintained its bacterial form when transferred onto a low-salt (NaCl) medium but was virtually completely induced into the L-form state on a high-salt medium. The original parent bacterial form was not sensitive to salt. The possibility is discussed that an L-form - bacterial-form cycle for this bacterium might occur naturally in soil. This cycle would be mediated by fluctuations in local salt concentrations in the soil.

Stable gastric pentadecapeptide BPC 157-NO-system relation.

PubMed

Sikiric, Predrag; Seiwerth, Sven; Rucman, Rudolf; Turkovic, Branko; Rokotov, Dinko Stancic; Brcic, Luka; Sever, Marko; Klicek, Robert; Radic, Bozo; Drmic, Domagoj; Ilic, Spomenko; Kolenc, Danijela; Aralica, Gorana; Stupnisek, Mirjana; Suran, Jelena; Barisic, Ivan; Dzidic, Senka; Vrcic, Hrvoje; Sebecic, Bozidar

2014-01-01

We reviewed stable gastric pentadecapeptide BPC 157-NO-system-relation, its close participation in Moncada's (maintained vascular integrity, platelets control) homeostatic healing response of NO-system to injury. Namely, BPC 157's particular healing effect also affects all events after vascular integrity loss (dependent on circumstances, it reduces either thrombosis (abdominal aorta anastomosis) or bleeding/thrombocytopenia (amputation, heparin, warfarin, aspirin)) and in a series of different injurious models, acute and chronic, BPC 157 consistently advances healing after severe injuries in various tissues spontaneously unable to heal; stimulates egr-1 and naB2 genes; exhibits high safety (LD1 not achieved)). Hypothesis, that BPC 157 (since formed constitutively in the gastric mucosa, stable in human gastric juice, along with significance of NO-synthase and the basal formation of NO in stomach mucosa, greater than that seen in other tissues) exhibits a general, effective competing both with L-arginine analogues (i. e., L-NAME) and L-arginine, and that this has some physiologic importance (NO-generation), later, practically supports its beneficial effects illustrating BPC 157 and NOsystem mutual (with L-NAME/L-arginine; alone and together) relations in (i) gastric mucosa and mucosal protection, following alcohol lesions, in cytoprotection course, NO-generation, and blood pressure regulation; (ii) alcohol acute/chronic intoxication, and withdrawal; (iii) cardiovascular disturbances, chronic heart failure, pulmonary hypertension, and arrhythmias; (iv) disturbances after hypokalemia and hyperkalemia, and potassium-cell membrane dysfunction; and finally, in (v) complex healing failure, proved by the fistulas healing, colocutaneous and esophagocutaneous. However, how this advantage of modulating NO-system (i. e., particular effect on eNOS gene), may be practically translated into an enhanced clinical performance remains to be determined.

A physico-chemical assessment of the thermal stability of pneumococcal conjugate vaccine components

PubMed Central

Gao, Fang; Lockyer, Kay; Burkin, Karena; Crane, Dennis T; Bolgiano, Barbara

2014-01-01

Physico-chemical analysis of pneumococcal polysaccharide (PS)-protein conjugate vaccine components used for two commercially licensed vaccines was performed to compare the serotype- and carrier protein-specific stabilities of these vaccines. Nineteen different monovalent pneumococcal conjugates from commercial vaccines utilizing CRM197, diphtheria toxoid (DT), Protein D (PD) or tetanus toxoid (TT) as carrier proteins were incubated at temperatures up to 56°C for up to eight weeks or were subjected to freeze-thawing (F/T). Structural stability was evaluated by monitoring their size, integrity and carrier protein conformation. The molecular size of the vaccine components was well maintained for Protein D, TT and DT conjugates at -20°C, 4°C and F/T, and for CRM197 conjugates at 4°C and F/T. It was observed that four of the eight serotypes of Protein D conjugates tended to form high molecular weight complexes at 37°C or above. The other conjugated carrier proteins also appeared to form oligomers or ‘aggregates’ at elevated temperatures, but rarely when frozen and thawed. There was evidence of degradation in some of the conjugates as evidenced by the formation of lower molecular weight materials which correlated with measured free saccharide. In conclusion, pneumococcal-Protein D/TT/DT and most CRM197 bulk conjugate vaccines were stable when stored at 2–8°C, the recommended temperature. In common between the conjugates produced by the two manufacturers, serotypes 1, 5, and 19F were relatively less stable and 6B was the most stable, with types 7F and 23F also showing good stability. PMID:25483488

Guidance of Nonlinear Nonminimum-Phase Dynamic Systems

NASA Technical Reports Server (NTRS)

Devasia, Santosh

1996-01-01

The research work has advanced the inversion-based guidance theory for: systems with non-hyperbolic internal dynamics; systems with parameter jumps; and systems where a redesign of the output trajectory is desired. A technique to achieve output tracking for nonminimum phase linear systems with non-hyperbolic and near non-hyperbolic internal dynamics was developed. This approach integrated stable inversion techniques, that achieve exact-tracking, with approximation techniques, that modify the internal dynamics to achieve desirable performance. Such modification of the internal dynamics was used (a) to remove non-hyperbolicity which is an obstruction to applying stable inversion techniques and (b) to reduce large preactuation times needed to apply stable inversion for near non-hyperbolic cases. The method was applied to an example helicopter hover control problem with near non-hyperbolic internal dynamics for illustrating the trade-off between exact tracking and reduction of preactuation time. Future work will extend these results to guidance of nonlinear non-hyperbolic systems. The exact output tracking problem for systems with parameter jumps was considered. Necessary and sufficient conditions were derived for the elimination of switching-introduced output transient. While previous works had studied this problem by developing a regulator that maintains exact tracking through parameter jumps (switches), such techniques are, however, only applicable to minimum-phase systems. In contrast, our approach is also applicable to nonminimum-phase systems and leads to bounded but possibly non-causal solutions. In addition, for the case when the reference trajectories are generated by an exosystem, we developed an exact-tracking controller which could be written in a feedback form. As in standard regulator theory, we also obtained a linear map from the states of the exosystem to the desired system state, which was defined via a matrix differential equation.

Ambient stable quantitative PCR reagents for the detection of Yersinia pestis.

PubMed

Qu, Shi; Shi, Qinghai; Zhou, Lei; Guo, Zhaobiao; Zhou, Dongsheng; Zhai, Junhui; Yang, Ruifu

2010-03-09

Although assays for detecting Yersinia pestis using TaqMan probe-based real-time PCR have been developed for years, little is reported on room-temperature-stable PCR reagents, which will be invaluable for field epidemic surveillance, immediate response to public health emergencies, counter-bioterrorism investigation, etc. In this work, a set of real-time PCR reagents for rapid detection of Y. pestis was developed with extraordinary stability at 37 degrees C. TaqMan-based real-time PCR assays were developed using the primers and probes targeting the 3a sequence in the chromosome and the F1 antigen gene caf1 in the plasmid pMT1of Y. pestis, respectively. Then, carbohydrate mixtures were added to the PCR reagents, which were later vacuum-dried for stability evaluation. The vacuum-dried reagents were stable at 37 degrees C for at least 49 days for a lower concentration of template DNA (10 copies/microl), and up to 79 days for higher concentrations (> or =10(2) copies/microl). The reagents were used subsequently to detect soil samples spiked with Y. pestis vaccine strain EV76, and 5x10(4) CFU per gram of soil could be detected by both 3a- and caf1-based PCR reagents. In addition, a simple and efficient method for soil sample processing is presented here. The vacuum-dried reagents for real-time PCR maintain accuracy and reproducibility for at least 49 days at 37 degrees C, indicating that they can be easily transported at room temperature for field application if the machine for performing real-time PCR is available. This dry reagent is of great significance for routine plague surveillance.

Ambient Stable Quantitative PCR Reagents for the Detection of Yersinia pestis

PubMed Central

Zhou, Lei; Guo, Zhaobiao; Zhou, Dongsheng; Zhai, Junhui; Yang, Ruifu

2010-01-01

Background Although assays for detecting Yersinia pestis using TaqMan probe-based real-time PCR have been developed for years, little is reported on room-temperature-stable PCR reagents, which will be invaluable for field epidemic surveillance, immediate response to public health emergencies, counter-bioterrorism investigation, etc. In this work, a set of real-time PCR reagents for rapid detection of Y. pestis was developed with extraordinary stability at 37°C. Methods/Principal Findings TaqMan-based real-time PCR assays were developed using the primers and probes targeting the 3a sequence in the chromosome and the F1 antigen gene caf1 in the plasmid pMT1of Y. pestis, respectively. Then, carbohydrate mixtures were added to the PCR reagents, which were later vacuum-dried for stability evaluation. The vacuum-dried reagents were stable at 37°C for at least 49 days for a lower concentration of template DNA (10 copies/µl), and up to 79 days for higher concentrations (≥102 copies/µl). The reagents were used subsequently to detect soil samples spiked with Y. pestis vaccine strain EV76, and 5×104 CFU per gram of soil could be detected by both 3a- and caf1-based PCR reagents. In addition, a simple and efficient method for soil sample processing is presented here. Conclusions/Significance The vacuum-dried reagents for real-time PCR maintain accuracy and reproducibility for at least 49 days at 37°C, indicating that they can be easily transported at room temperature for field application if the machine for performing real-time PCR is available. This dry reagent is of great significance for routine plague surveillance. PMID:20231881

Long-Term Stability of Tramadol and Ketamine Solutions for Patient-Controlled Analgesia Delivery

PubMed Central

Gu, Junfeng; Qin, Wengang; Chen, Fuchao; Xia, Zhongyuan

2015-01-01

Background Subanesthetic doses of ketamine as an adjuvant to tramadol in patient-controlled analgesia (PCA) for postoperative pain have been shown to improve the quality of analgesia. However, there are no such commercially available drug mixtures, and the stability of the combination has rarely been assessed. Material/Methods Admixtures were assessed for periods of up to 14 days at 4°C and 25°C. Three different mixtures of tramadol and ketamine (tramadol 5.0 mg/mL + ketamine 0.5 mg/mL, tramadol 5.0 mg/mL + ketamine 1.0 mg/mL, and tramadol 5.0 mg/mL + ketamine 2.0 mg/mL) were prepared in polyolefin bags by combining these 2 drugs with 0.9% sodium chloride (normal saline [NS]). The chemical stability of the admixtures was evaluated by a validated high-performance liquid chromatography (HPLC) method and by measurement of pH values. Solution appearance and color were assessed by observing the samples against black and white backgrounds. Solutions were considered stable if they maintained 90% of the initial concentration of each drug. Results The percentages of initial concentration of tramadol and ketamine in the various solutions remained above 98% when stored at 4°C or 25°C over the testing period. No changes in color or turbidity were observed in any of the prepared solutions. Throughout this period, pH values remained stable. Conclusions The results indicate that the drug mixtures of tramadol with ketamine in NS for PCA delivery systems were stable for 14 days when stored in polyolefin bags at 4°C or 25°C. PMID:26306476

Production and certification of NIST Standard Reference Material 2372 Human DNA Quantitation Standard.

PubMed

Kline, Margaret C; Duewer, David L; Travis, John C; Smith, Melody V; Redman, Janette W; Vallone, Peter M; Decker, Amy E; Butler, John M

2009-06-01

Modern highly multiplexed short tandem repeat (STR) assays used by the forensic human-identity community require tight control of the initial amount of sample DNA amplified in the polymerase chain reaction (PCR) process. This, in turn, requires the ability to reproducibly measure the concentration of human DNA, [DNA], in a sample extract. Quantitative PCR (qPCR) techniques can determine the number of intact stretches of DNA of specified nucleotide sequence in an extremely small sample; however, these assays must be calibrated with DNA extracts of well-characterized and stable composition. By 2004, studies coordinated by or reported to the National Institute of Standards and Technology (NIST) indicated that a well-characterized, stable human DNA quantitation certified reference material (CRM) could help the forensic community reduce within- and among-laboratory quantitation variability. To ensure that the stability of such a quantitation standard can be monitored and that, if and when required, equivalent replacement materials can be prepared, a measurement of some stable quantity directly related to [DNA] is required. Using a long-established conventional relationship linking optical density (properly designated as decadic attenuance) at 260 nm with [DNA] in aqueous solution, NIST Standard Reference Material (SRM) 2372 Human DNA Quantitation Standard was issued in October 2007. This SRM consists of three quite different DNA extracts: a single-source male, a multiple-source female, and a mixture of male and female sources. All three SRM components have very similar optical densities, and thus very similar conventional [DNA]. The materials perform very similarly in several widely used gender-neutral assays, demonstrating that the combination of appropriate preparation methods and metrologically sound spectrophotometric measurements enables the preparation and certification of quantitation [DNA] standards that are both maintainable and of practical utility.

Childhood Family Structure and Intergenerational Income Mobility in the United States.

PubMed

Bloome, Deirdre

2017-04-01

The declining prevalence of two-parent families helped increase income inequality over recent decades. Does family structure also condition how economic (dis)advantages pass from parents to children? If so, shifts in the organization of family life may contribute to enduring inequality between groups defined by childhood family structure. Using National Longitudinal Survey of Youth data, I combine parametric and nonparametric methods to reveal how family structure moderates intergenerational income mobility in the United States. I find that individuals raised outside stable two-parent homes are much more mobile than individuals from stable two-parent families. Mobility increases with the number of family transitions but does not vary with children's time spent coresiding with both parents or stepparents conditional on a transition. However, this mobility indicates insecurity, not opportunity. Difficulties maintaining middle-class incomes create downward mobility among people raised outside stable two-parent homes. Regardless of parental income, these people are relatively likely to become low-income adults, reflecting a new form of perverse equality. People raised outside stable two-parent families are also less likely to become high-income adults than people from stable two-parent homes. Mobility differences account for about one-quarter of family-structure inequalities in income at the bottom of the income distribution and more than one-third of these inequalities at the top.

Development of Stable Liquid Glucagon Formulations for Use in Artificial Pancreas

PubMed Central

Li, Ming; Krasner, Alan; De Souza, Errol

2014-01-01

Background: A promising approach to treat diabetes is the development of fully automated artificial/bionic pancreas systems that use both insulin and glucagon to maintain euglycemia. A physically and chemically stable liquid formulation of glucagon does not currently exist. Our goal is to develop a glucagon formulation that is stable as a clear and gel-free solution, free of fibrils and that has the requisite long-term shelf life for storage in the supply chain, short-term stability for at least 7 days at 37°C, and pump compatibility for use in a bihormonal pump. Methods: We report the development of two distinct families of stable liquid glucagon formulations which utilize surfactant or surfactant-like excipients (LMPC and DDM) to “immobilize” the glucagon in solution potentially through the formation of micelles and prevention of interaction between glucagon molecules. Results: Data are presented that demonstrate long-term physical and chemical stability (~2 years) at 5°C, short-term stability (up to 1 month) under accelerated 37°C testing conditions, pump compatibility for up to 9 days, and adequate glucose responses in dogs and diabetic swine. Conclusions: These stable glucagon formulations show utility and promise for further development in artificial pancreas systems. PMID:25352634

Comparison of the Performance of the Warfarin Pharmacogenetics Algorithms in Patients with Surgery of Heart Valve Replacement and Heart Valvuloplasty.

PubMed

Xu, Hang; Su, Shi; Tang, Wuji; Wei, Meng; Wang, Tao; Wang, Dongjin; Ge, Weihong

2015-09-01

A large number of warfarin pharmacogenetics algorithms have been published. Our research was aimed to evaluate the performance of the selected pharmacogenetic algorithms in patients with surgery of heart valve replacement and heart valvuloplasty during the phase of initial and stable anticoagulation treatment. 10 pharmacogenetic algorithms were selected by searching PubMed. We compared the performance of the selected algorithms in a cohort of 193 patients during the phase of initial and stable anticoagulation therapy. Predicted dose was compared to therapeutic dose by using a predicted dose percentage that falls within 20% threshold of the actual dose (percentage within 20%) and mean absolute error (MAE). The average warfarin dose for patients was 3.05±1.23mg/day for initial treatment and 3.45±1.18mg/day for stable treatment. The percentages of the predicted dose within 20% of the therapeutic dose were 44.0±8.8% and 44.6±9.7% for the initial and stable phases, respectively. The MAEs of the selected algorithms were 0.85±0.18mg/day and 0.93±0.19mg/day, respectively. All algorithms had better performance in the ideal group than in the low dose and high dose groups. The only exception is the Wadelius et al. algorithm, which had better performance in the high dose group. The algorithms had similar performance except for the Wadelius et al. and Miao et al. algorithms, which had poor accuracy in our study cohort. The Gage et al. algorithm had better performance in both phases of initial and stable treatment. Algorithms had relatively higher accuracy in the >50years group of patients on the stable phase. Copyright © 2015 Elsevier Ltd. All rights reserved.

Generating mammalian stable cell lines by electroporation.

PubMed

A Longo, Patti; Kavran, Jennifer M; Kim, Min-Sung; Leahy, Daniel J

2013-01-01

Expression of functional, recombinant mammalian proteins often requires expression in mammalian cells (see Single Cell Cloning of a Stable Mammalian Cell Line). If the expressed protein needs to be made frequently, it can be best to generate a stable cell line instead of performing repeated transient transfections into mammalian cells. Here, we describe a method to generate stable cell lines via electroporation followed by selection steps. This protocol will be limited to the CHO dhfr-Urlaub et al. (1983) and LEC1 cell lines, which in our experience perform the best with this method. Copyright © 2013 Elsevier Inc. All rights reserved.

Increasing Resilience to Traumatic Stress: Understanding the Protective Role of Well-Being.

PubMed

Tory Toole, J; Rice, Mark A; Cargill, Jordan; Craddock, Travis J A; Nierenberg, Barry; Klimas, Nancy G; Fletcher, Mary Ann; Morris, Mariana; Zysman, Joel; Broderick, Gordon

2018-01-01

The brain maintains homeostasis in part through a network of feedback and feed-forward mechanisms, where neurochemicals and immune markers act as mediators. Using a previously constructed model of biobehavioral feedback, we found that in addition to healthy equilibrium another stable regulatory program supported chronic depression and anxiety. Exploring mechanisms that might underlie the contributions of subjective well-being to improved therapeutic outcomes in depression, we iteratively screened 288 candidate feedback patterns linking well-being to molecular signaling networks for those that maintained the original homeostatic regimes. Simulating stressful trigger events on each candidate network while maintaining high levels of subjective well-being isolated a specific feedback network where well-being was promoted by dopamine and acetylcholine, and itself promoted norepinephrine while inhibiting cortisol expression. This biobehavioral feedback mechanism was especially effective in reproducing well-being's clinically documented ability to promote resilience and protect against onset of depression and anxiety.

An extra-uterine system to physiologically support the extreme premature lamb

PubMed Central

Partridge, Emily A.; Davey, Marcus G.; Hornick, Matthew A.; McGovern, Patrick E.; Mejaddam, Ali Y.; Vrecenak, Jesse D.; Mesas-Burgos, Carmen; Olive, Aliza; Caskey, Robert C.; Weiland, Theodore R.; Han, Jiancheng; Schupper, Alexander J.; Connelly, James T.; Dysart, Kevin C.; Rychik, Jack; Hedrick, Holly L.; Peranteau, William H.; Flake, Alan W.

2017-01-01

In the developed world, extreme prematurity is the leading cause of neonatal mortality and morbidity due to a combination of organ immaturity and iatrogenic injury. Until now, efforts to extend gestation using extracorporeal systems have achieved limited success. Here we report the development of a system that incorporates a pumpless oxygenator circuit connected to the fetus of a lamb via an umbilical cord interface that is maintained within a closed ‘amniotic fluid' circuit that closely reproduces the environment of the womb. We show that fetal lambs that are developmentally equivalent to the extreme premature human infant can be physiologically supported in this extra-uterine device for up to 4 weeks. Lambs on support maintain stable haemodynamics, have normal blood gas and oxygenation parameters and maintain patency of the fetal circulation. With appropriate nutritional support, lambs on the system demonstrate normal somatic growth, lung maturation and brain growth and myelination. PMID:28440792

Spacecraft Radiator Freeze Protection Using a Regenerative Heat Exchanger

NASA Technical Reports Server (NTRS)

Ungar, Eugene K.; Schunk, Richard G.

2011-01-01

An active thermal control system architecture has been modified to include a regenerative heat exchanger (regenerator) inboard of the radiator. Rather than using a radiator bypass valve a regenerative heat exchanger is placed inboard of the radiators. A regenerator cold side bypass valve is used to set the return temperature. During operation, the regenerator bypass flow is varied, mixing cold radiator return fluid and warm regenerator outlet fluid to maintain the system setpoint. At the lowest heat load for stable operation, the bypass flow is closed off, sending all of the flow through the regenerator. This lowers the radiator inlet temperature well below the system set-point while maintaining full flow through the radiators. By using a regenerator bypass flow control to maintain system setpoint, the required minimum heat load to avoid radiator freezing can be reduced by more than half compared to a radiator bypass system.

Chm-1 gene-modified bone marrow mesenchymal stem cells maintain the chondrogenic phenotype of tissue-engineered cartilage.

PubMed

Chen, Zhuoyue; Wei, Jing; Zhu, Jun; Liu, Wei; Cui, Jihong; Li, Hongmin; Chen, Fulin

2016-05-05

Marrow mesenchymal stem cells (MSCs) can differentiate into specific phenotypes, including chondrocytes, and have been widely used for cartilage tissue engineering. However, cartilage grafts from MSCs exhibit phenotypic alternations after implantation, including matrix calcification and vascular ingrowth. We compared chondromodulin-1 (Chm-1) expression between chondrocytes and MSCs. We found that chondrocytes expressed a high level of Chm-1. We then adenovirally transduced MSCs with Chm-1 and applied modified cells to engineer cartilage in vivo. A gross inspection and histological observation indicated that the chondrogenic phenotype of the tissue-engineered cartilage graft was well maintained, and the stable expression of Chm-1 was detected by immunohistological staining in the cartilage graft derived from the Chm-1 gene-modified MSCs. Our findings defined an essential role for Chm-1 in maintaining chondrogenic phenotype and demonstrated that Chm-1 gene-modified MSCs may be used in cartilage tissue engineering.

An extra-uterine system to physiologically support the extreme premature lamb

NASA Astrophysics Data System (ADS)

Partridge, Emily A.; Davey, Marcus G.; Hornick, Matthew A.; McGovern, Patrick E.; Mejaddam, Ali Y.; Vrecenak, Jesse D.; Mesas-Burgos, Carmen; Olive, Aliza; Caskey, Robert C.; Weiland, Theodore R.; Han, Jiancheng; Schupper, Alexander J.; Connelly, James T.; Dysart, Kevin C.; Rychik, Jack; Hedrick, Holly L.; Peranteau, William H.; Flake, Alan W.

2017-04-01

In the developed world, extreme prematurity is the leading cause of neonatal mortality and morbidity due to a combination of organ immaturity and iatrogenic injury. Until now, efforts to extend gestation using extracorporeal systems have achieved limited success. Here we report the development of a system that incorporates a pumpless oxygenator circuit connected to the fetus of a lamb via an umbilical cord interface that is maintained within a closed `amniotic fluid' circuit that closely reproduces the environment of the womb. We show that fetal lambs that are developmentally equivalent to the extreme premature human infant can be physiologically supported in this extra-uterine device for up to 4 weeks. Lambs on support maintain stable haemodynamics, have normal blood gas and oxygenation parameters and maintain patency of the fetal circulation. With appropriate nutritional support, lambs on the system demonstrate normal somatic growth, lung maturation and brain growth and myelination.

An Army Force Structure for the Future

DTIC Science & Technology

1992-03-31

realization: deterring aggression; ensuring access to foreign markets , energy, mineral resources, the oceans, and space; maintaining stable regional...establish the optimum organisational mix for independent and highly flexible operational-level activity." 7 Two factors are driving this structural change...armored forces; and optimizing the force mix of the three. However, before describing the specific changes needed to shape the future Army, a delineation

Sirt1 Protects Stressed Adult Hematopoietic Stem Cells | Center for Cancer Research

Cancer.gov

The immune system relies on a stable pool of hematopoietic stem and progenitor cells (HSPCs) to respond properly to injury or stress. Maintaining genomic integrity and appropriate gene expression is essential for HSPC homeostasis, and dysregulation can result in myeloproliferative disorders or loss of immune function. Sirt1 is a histone deacetylase that can protect embryonic

Digitally-Enabled Organizational Routines at the Organization-Environment Boundary: Buffering and the Role of Technology

ERIC Educational Resources Information Center

Hillison, Derek William

2009-01-01

Boundary units of an organization uniquely experience the tension between adaptation to environmental variation and maintaining stable outcomes for the rest of the organization. In our world of just-in-time supply chain systems, lot-sizes of one, lean manufacturing and an increasing focus on services, traditional forms of buffering such as queuing…

Oil prospects attract workover dollars. [Rocky Mountains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stremel, K.

1983-12-01

Anticipating stable crude oil prices and low service costs, Rocky Mountain operators plan to maintain strong workover programs next year. Deflated service costs are allowing operators to complete more workovers without appropriating more capital, and they plan to take advantage of the bargain prices available in the oilpatch. Workover activity next year will be concentrated in major oil producing basins of the Rockies.

Tunable erbium-doped fiber laser based on optical fiber Sagnac interference loop with angle shift spliced polarization maintaining fibers

NASA Astrophysics Data System (ADS)

Ding, Zhenming; Wang, Zhaokun; Zhao, Chunliu; Wang, Dongning

2018-05-01

In this paper, we propose and experimentally demonstrate a tunable erbium-doped fiber laser (EDFL) with Sagnac interference loop with 45° angle shift spliced polarization maintaining fibers (PMFs). In the Sagnac loop, two PMFs with similar lengths. The Sagnac loop outputs a relatively complex interference spectrum since two beams transmitted in clockwise and counterclockwise encounter at the 3 dB coupler, interfere, and form two interference combs when the light transmitted in the Sagnac loop. The laser will excite and be stable when two interference lines in these two interference combs overlap together. Then by adjusting the polarization controller, the wide wavelength tuning is realized. Experimental results show that stable single wavelength laser can be realized in the wavelength range of 1585 nm-1604 nm under the pump power 157.1 mW. The side-mode suppression ratio is not less than 53.9 dB. The peak power fluctuation is less than 0.29 dB within 30 min monitor time and the side-mode suppression ratio is great than 57.49 dB when the pump power is to 222.7 mW.